WorldWideScience

Sample records for lummus gin stand

  1. Pilot scale cotton gin trash energy recovery

    Energy Technology Data Exchange (ETDEWEB)

    Harp, S.L. [Oklahoma State Univ., Stillwater, OK (United States)

    1993-12-31

    During the summer of 1992 a 520,000 kcal/h (2,064,400 Btu/hr) biomass combustor was installed at a cotton gin in southwestern Oklahoma. The gin has a capacity of approximately 35 bales per hour. Each bale of cotton ginned weighs about 227 kg (500 lb) and produces about 68 kg (150 lb) of trash. Therefore, this gin produces about 52,360 kg (115,500 lb) of trash per day during a typical ginning season. Approximately 2 million kg (4 million lb) of gin trash are produced at this site each year. Cotton must first be dried to about 3-5% moisture content before the ginning process is begun. To accomplish this at this gin, two six million Btu/hour direct fired gas heaters are used to heat air for drying the cotton. The biomass combustor was installed to operate in parallel with one of the heaters to supply heated air for the drying process. A pneumatic conveying system was installed to intercept a portion of the gin trash and divert it to the burner. The burner was operated during the 1992 ginning season, which lasted from September through November, with few problems.

  2. Cotton gin electrical energy use trends and 2009 audit results

    Science.gov (United States)

    Cotton gin energy costs have risen more than other operating costs. Energy audits were conducted in twenty US cotton gins representing a range of capacities in six states. The average participating saw gin used 39.5 kWh to process a bale. The average roller gin used 62.6 kWh. Gins have become la...

  3. Energy usage for cotton ginning in Australia

    Energy Technology Data Exchange (ETDEWEB)

    Ismail, S.A. [MARA Univ. of Technology, Shah Alam (Malaysia). Faculty of Applied Sciences; Southern Queensland Univ., Toowoomba, QLD (Australia). National Centre for Engineering in Agriculture; Chen, G.; Baillie, C.; Symes, T. [Southern Queensland Univ., Toowoomba, QLD (Australia). National Centre for Engineering in Agriculture

    2010-07-01

    This paper reported on a study that evaluated the energy consumption of cotton gins used in Australia. The average electricity use is 52.3 kWh per bale. In practicality, the electricity consumption for different gins is correlated linearly with the bale numbers produced. The cost of electricity is therefore important in cotton ginning operations. The power factor in all the gins monitored in this study was greater than 0.85. The study showed that the use of gas dryers was highly influenced by the cotton moisture and regulated drying temperature. In general, electricity and gas consumption comprised 61 and 39 per cent of total energy use respectively. The study showed that 60.38 kg of carbon dioxide are emitted for ginning each bale of cotton. This paper described a newly developed method for monitoring the energy performance in cotton gins. Detailed monitoring and analysis carried out at 2 gin sites revealed that electricity consumption is not influenced much by changes in trash content in the module, degree of moisture and lint quality. However, the cotton variety influences the energy consumption. Cotton handling constituted nearly 50 per cent of the power used in both gins.

  4. The Cost of Ginning Cotton - 2007 Survey Results

    Science.gov (United States)

    The 2007 United States cotton crop was 18.7 million running bales, 11 percent below 2006 production. This crop was gathered from 10.2 million acres, which yielded a record high 879 pounds per acre and was ginned with 806 operating gins, averaging over 23,000 bales per gin. There has been a yearly ...

  5. Changes in cotton gin energy consumption apportioned by ten functions

    Science.gov (United States)

    The public is concerned about air quality and sustainability. Cotton producers, gin owners and plant managers are concerned about rising energy prices. Both have an interest in cotton gin energy consumption trends. Changes in cotton gins’ energy consumption over the past fifty years, a period of ...

  6. Economics of oversized cyclones in the cotton ginning industry

    Science.gov (United States)

    Cost of reducing pollution to meet increasingly stringent air quality standards particularly for the U.S. cotton ginning industry is rising overtime. Most industry participants use cyclones to control air pollutants. These cyclones have no moving parts and their initial investment costs are relative...

  7. Modernity rejected? Marketing schnapps gin in West Africa, 1945 ...

    African Journals Online (AJOL)

    During the 1950s and 1960s, advertising for a diverse range of products, ... why African consumers rejected the claim that schnapps gin was „modern‟, and why ... used and interpreted on a day-to-day level during the decolonisation era. ... on marketing and consumption of imported commodities in twentieth-century Africa.

  8. An OmpA Family Protein, a Target of the GinI/GinR Quorum-Sensing System in Gluconacetobacter intermedius, Controls Acetic Acid Fermentation▿ †

    Science.gov (United States)

    Iida, Aya; Ohnishi, Yasuo; Horinouchi, Sueharu

    2008-01-01

    Via N-acylhomoserine lactones, the GinI/GinR quorum-sensing system in Gluconacetobacter intermedius NCI1051, a gram-negative acetic acid bacterium, represses acetic acid and gluconic acid fermentation. Two-dimensional polyacrylamide gel electrophoretic analysis of protein profiles of strain NCI1051 and ginI and ginR mutants identified a protein that was produced in response to the GinI/GinR regulatory system. Cloning and nucleotide sequencing of the gene encoding this protein revealed that it encoded an OmpA family protein, named GmpA. gmpA was a member of the gene cluster containing three adjacent homologous genes, gmpA to gmpC, the organization of which appeared to be unique to vinegar producers, including “Gluconacetobacter polyoxogenes.” In addition, GmpA was unique among the OmpA family proteins in that its N-terminal membrane domain forming eight antiparallel transmembrane β-strands contained an extra sequence in one of the surface-exposed loops. Transcriptional analysis showed that only gmpA of the three adjacent gmp genes was activated by the GinI/GinR quorum-sensing system. However, gmpA was not controlled directly by GinR but was controlled by an 89-amino-acid protein, GinA, a target of this quorum-sensing system. A gmpA mutant grew more rapidly in the presence of 2% (vol/vol) ethanol and accumulated acetic acid and gluconic acid in greater final yields than strain NCI1051. Thus, GmpA plays a role in repressing oxidative fermentation, including acetic acid fermentation, which is unique to acetic acid bacteria and allows ATP synthesis via ethanol oxidation. Consistent with the involvement of gmpA in oxidative fermentation, its transcription was also enhanced by ethanol and acetic acid. PMID:18487322

  9. An OmpA family protein, a target of the GinI/GinR quorum-sensing system in Gluconacetobacter intermedius, controls acetic acid fermentation.

    Science.gov (United States)

    Iida, Aya; Ohnishi, Yasuo; Horinouchi, Sueharu

    2008-07-01

    Via N-acylhomoserine lactones, the GinI/GinR quorum-sensing system in Gluconacetobacter intermedius NCI1051, a gram-negative acetic acid bacterium, represses acetic acid and gluconic acid fermentation. Two-dimensional polyacrylamide gel electrophoretic analysis of protein profiles of strain NCI1051 and ginI and ginR mutants identified a protein that was produced in response to the GinI/GinR regulatory system. Cloning and nucleotide sequencing of the gene encoding this protein revealed that it encoded an OmpA family protein, named GmpA. gmpA was a member of the gene cluster containing three adjacent homologous genes, gmpA to gmpC, the organization of which appeared to be unique to vinegar producers, including "Gluconacetobacter polyoxogenes." In addition, GmpA was unique among the OmpA family proteins in that its N-terminal membrane domain forming eight antiparallel transmembrane beta-strands contained an extra sequence in one of the surface-exposed loops. Transcriptional analysis showed that only gmpA of the three adjacent gmp genes was activated by the GinI/GinR quorum-sensing system. However, gmpA was not controlled directly by GinR but was controlled by an 89-amino-acid protein, GinA, a target of this quorum-sensing system. A gmpA mutant grew more rapidly in the presence of 2% (vol/vol) ethanol and accumulated acetic acid and gluconic acid in greater final yields than strain NCI1051. Thus, GmpA plays a role in repressing oxidative fermentation, including acetic acid fermentation, which is unique to acetic acid bacteria and allows ATP synthesis via ethanol oxidation. Consistent with the involvement of gmpA in oxidative fermentation, its transcription was also enhanced by ethanol and acetic acid.

  10. Overflow system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  11. 1st stage mote system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts to characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was f...

  12. 2nd stage lint cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  13. 1st stage lint cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  14. Mote cleaner system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  15. Combined mote system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  16. Mote cyclone robber system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  17. Unloading system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  18. Mote trash system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  19. Combined lint cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  20. Cyclone robber system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  1. 2nd stage mote system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  2. Master trash system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  3. 7 CFR 319.8-9 - Hull fiber and gin trash.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 5 2010-01-01 2010-01-01 false Hull fiber and gin trash. 319.8-9 Section 319.8-9 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION... Importation and Entry of Cotton and Covers § 319.8-9 Hull fiber and gin trash. (a) Entry of hull fiber will be...

  4. Battery condenser system total particulate emission factors and rates for cotton gins: Method 17

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  5. Battery condenser system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that to characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study ...

  6. Battery condenser system total particulate emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  7. Characterization of cotton gin PM10 emissions based on EPA stack sampling methodologies and particle size distributions

    Science.gov (United States)

    A project to characterize cotton gin emissions in terms of stack sampling was conducted during the 2008 through 2011 ginning seasons. The impetus behind the project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. EPA AP-42 emission factors ar...

  8. Cotton gin trash in the western United States: Resource inventory and energy conversion characterization

    Energy Technology Data Exchange (ETDEWEB)

    Haase, S.G.; Quinn, M.W.; Whittier, J.P. [NEOS Corp., Lakewood, CO (United States); Cohen, T.M.; Lansford, R.R. [New Mexico State Univ., Las Cruces, NM (United States); Craig, J.D. [Cratech Inc., Tahoka, TX (United States); Swanson, D.S.; Morgan, G. [Western Regional Biomass Energy Program, Golden, CO (United States)

    1993-12-31

    The disposal of wastes associated with the processing of cotton is posing increasing problems for cotton gin operators in the western United States. Traditional disposal methods, such as open-air incineration and landfilling are no longer adequate due to increasing environmental concerns. This paper evaluates the technical, economic and environmental feasibility for cotton gin trash to serve as an energy resource. Cotton gin trash has been quantified, by county, in the five cotton-growing states of the western United States. The energy conversion technology that appears to offer the most promise is gasification. An economic evaluation model has been developed that will allow gin operators to analyze their own situation to determine the profitability of converting gin trash to energy.

  9. Hearing impairment among workers exposed to excessive levels of noise in ginning industries

    Directory of Open Access Journals (Sweden)

    Kamalesh J Dube

    2011-01-01

    Full Text Available Cotton ginning workers have a risk of hearing loss due to excessive noise levels at the workplace environment. In this study, estimates of typical sound levels prevailing at the workplace environment and its effects on hearing ability of the exposed workers were made among cotton ginning workers. Data on self-reported health status was collected by a questionnaire survey at 10 cotton ginning industries located at Jalgaon district of Maharashtra state, India. The cotton ginning workers were exposed to continuous noise levels between 89 and 106 dBA. The hearing ability of the subjects was accessed by pure tone audiometry. The results of audiometry show mild, moderate and moderately severe degree of hearing impairment among the cotton ginning workers. The data generated during the study show that hearing loss was significantly associated with period of exposure to the workplace noise (P <0.0001. The prevalence of audiometric hearing impairment defined as a threshold average greater than 25 dB hearing level was 96% for binaural low-frequency average, 97% for binaural mid frequency average and 94% for binaural high-frequency average in the cotton ginning workers. We recommend the compulsory use of personal protective equipment like ear plug by the cotton ginning workers at the workplace environment. A regular maintenance of ginning and pressing machineries will avoid the emission of excessive noise at the workplace environment of cotton gins. A regular periodic medical examination is necessary to measure the impact of workplace noise on the health of cotton ginning workers.

  10. Work health and safety in cotton ginning industry: a survey of practices in australia

    International Nuclear Information System (INIS)

    Soomro, N.

    2015-01-01

    This survey focuses on the WH and S (Work Health and Safety) practices in Australia and relates them with those in Pakistan. It also highlights the planned areas of work required on WH and S in cotton ginning industry of Pakistan. This article is one a series of research studies that will inform a broader approach development. The aim of the survey was to design a standardized health and safety Act for cotton ginning industry of Pakistan and to help ginners meet their due industry obligations under the model WH and S Act. The first component of the research study survey was to review the relevant Australian work and safety model as this provides a framework to protect the health, safety and welfare of all employees at work and of other people who might be affected by the job. The second aspect of the research study survey concerned site visits to cotton gins with the support of Australian Centre for Agricultural Health and Safety, Moree, NSW. During these visits the existing ginning process in terms of WH and S were reviewed. Informal interviews were also conducted with Gin Managers and Ginning Experts regarding WH and S in the Australian cotton ginning industry. (author)

  11. Drive Stands

    Data.gov (United States)

    Federal Laboratory Consortium — The Electrical Systems Laboratory (ESL)houses numerous electrically driven drive stands. A drive stand consists of an electric motor driving a gearbox and a mounting...

  12. 3rd stage seed-cotton cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  13. 2nd stage seed-cotton cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  14. 1st stage seed-cotton cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  15. Theoretical bases of rotation dynamics of raw materials poller with s ratify consideration for saw gin processing of cotton

    International Nuclear Information System (INIS)

    Saidov, Kh.; Babaeva, A.Kh.

    2005-01-01

    In this paper is examined motion of raw materials rollers on the base of a stratify models. Foe every layers of the rollers are determined dynamical influences for saw gin processing of cotton. It is noticed that in the gin processing of cotton the second layer of cotton roller plagues an important role

  16. Battery condenser system PM10 emission factors and rates for cotton gins: Method 201A PM10 sizing cyclones

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that to characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study ...

  17. GINS complex protein Sld5 recruits SIK1 to activate MCM helicase during DNA replication.

    Science.gov (United States)

    Joshi, Kiranmai; Shah, Varun Jayeshkumar; Maddika, Subbareddy

    2016-12-01

    In eukaryotes, proper loading and activation of MCM helicase at chromosomal origins plays a central role in DNA replication. Activation of MCM helicase requires its association with CDC45-GINS complex, but the mechanism of how this complex activates MCM helicase is poorly understood. Here we identified SIK1 (salt-inducible kinase 1), an AMPK related protein kinase, as a molecular link that connects GINS complex with MCM helicase activity. We demonstrated that Sld5 a component of GINS complex interacts with SIK1 and recruits it to the sites of DNA replication at the onset of S phase. Depletion of SIK1 leads to defective DNA replication. Further, we showed that SIK1 phosphorylates MCM2 at five conserved residues at its N-terminus, which is essential for the activation of MCM helicase. Collectively, our results suggest SIK1 as a novel integral component of CMG replicative helicase during eukaryotic DNA replication. Copyright © 2016 Elsevier Inc. All rights reserved.

  18. Ginásio Clube Português (GCP) : measuring customer satisfaction in services industry

    OpenAIRE

    Alves, Guilherme Fernandes Rito

    2015-01-01

    The objective of this thesis is to measure and analyze the customer satisfaction level in Ginásio Clube Português, by understanding the key determinants and consequences of customer satisfaction. After an exponential growth both in revenues and in number of clients between 1998 and 2011, Ginásio Clube Português is losing competitive edge due to the increasing competition in the high-end and low-cost markets as well as due to the effects of the economic downturn. Aiming to en...

  19. A microcultura de um ginásio de treinamento de ginástica artística feminina de alto rendimento

    OpenAIRE

    Mauricio dos Santos de Oliveira

    2014-01-01

    No esporte podemos identificar microculturas constituídas por um grupo de pessoas que compartilham valores, crenças, padrões de comportamentos e um sistema de símbolos, verbal e não verbal, que os distingue do meio cultural dominante. O ginásio é o espaço no qual as microculturas de Ginástica Artística (GA) estão resguardadas e mantém a preeminência das tradições que constituem, em âmbito maior, a macrocultura da modalidade. Nesse ambiente há uma teia de significados, supostamente compartilha...

  20. Development of cotton gin PM10 emission factors for EPA’s AP-42

    Science.gov (United States)

    The Compilation of Air Pollution Emission Factors (AP-42) emission factors are assigned ratings, from A (Excellent) to E (Poor), based on the quality of data used to develop them. All current PM10 cotton gin emission factors received quality ratings of D or lower. In an effort to improve these ratin...

  1. Update on the development of cotton gin PM10 emission factors for EPA's AP-42

    Science.gov (United States)

    A cotton ginning industry-supported project was initiated in 2008 to update the U.S. Environmental Protection Agency’s (EPA) Compilation of Air Pollution Emission Factors (AP-42) to include PM10 emission factors. This study develops emission factors from the PM10 emission factor data collected from ...

  2. Generalized INverse imaging (GIN): ultrafast fMRI with physiological noise correction.

    Science.gov (United States)

    Boyacioğlu, Rasim; Barth, Markus

    2013-10-01

    An ultrafast functional magnetic resonance imaging (fMRI) technique, called generalized inverse imaging (GIN), is proposed, which combines inverse imaging with a phase constraint-leading to a less underdetermined reconstruction-and physiological noise correction. A single 3D echo planar imaging (EPI) prescan is sufficient to obtain the necessary coil sensitivity information and reference images that are used to reconstruct standard images, so that standard analysis methods are applicable. A moving dots stimulus paradigm was chosen to assess the performance of GIN. We find that the spatial localization of activation for GIN is comparable to an EPI protocol and that maximum z-scores increase significantly. The high temporal resolution of GIN (50 ms) and the acquisition of the phase information enable unaliased sampling and regression of physiological signals. Using the phase time courses obtained from the 32 channels of the receiver coils as nuisance regressors in a general linear model results in significant improvement of the functional activation, rendering the acquisition of external physiological signals unnecessary. The proposed physiological noise correction can in principle be used for other fMRI protocols, such as simultaneous multislice acquisitions, which acquire the phase information sufficiently fast and sample physiological signals unaliased. Copyright © 2012 Wiley Periodicals, Inc.

  3. Battery condenser system particulate emission factors for cotton gins: Particle size distribution characteristics

    Science.gov (United States)

    This report is part of a project to characterize cotton gin emissions from the standpoint of total particulate stack sampling and particle size analyses. In 2013, the Environmental Protection Agency (EPA) published a more stringent standard for particulate matter with nominal diameter less than or e...

  4. Battery condenser system PM2.5 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that detail a project to characterize cotton gin emissions from the standpoint of stack and ambient sampling. The impetus behind the project was the 2006 EPA implementation of a more stringent standard for particulate matter less than or equal to 2....

  5. 100 Years of Cotton Production, Harvesting and Ginning Systems Engineering: 1907 - 2007

    Science.gov (United States)

    The American Society of Agricultural and Biological Engineers (ASABE) celebrated its centennial year during 2007. As part of the ASABE centennial, the authors were asked to describe agricultural engineering accomplishments in U.S. cotton production, harvesting and ginning over the past 100 years. ...

  6. 29 CFR 780.806 - Exempt ginning limited to first processing.

    Science.gov (United States)

    2010-07-01

    ... cottonseed, is not exempt under section 13(b)(15). It is not first processing of the seed cotton; rather, it... 29 Labor 3 2010-07-01 2010-07-01 false Exempt ginning limited to first processing. 780.806 Section... AGRICULTURE, PROCESSING OF AGRICULTURAL COMMODITIES, AND RELATED SUBJECTS UNDER THE FAIR LABOR STANDARDS ACT...

  7. Geosciences Information Network (GIN): A modular, distributed, interoperable data network for the geosciences

    Science.gov (United States)

    Allison, M.; Gundersen, L. C.; Richard, S. M.; Dickinson, T. L.

    2008-12-01

    A coalition of the state geological surveys (AASG), the U.S. Geological Survey (USGS), and partners will receive NSF funding over 3 years under the INTEROP solicitation to start building the Geoscience Information Network (www.geoinformatics.info/gin) a distributed, interoperable data network. The GIN project will develop standardized services to link existing and in-progress components using a few standards and protocols, and work with data providers to implement these services. The key components of this network are 1) catalog system(s) for data discovery; 2) service definitions for interfaces for searching catalogs and accessing resources; 3) shared interchange formats to encode information for transmission (e.g. various XML markup languages); 4) data providers that publish information using standardized services defined by the network; and 5) client applications adapted to use information resources provided by the network. The GIN will integrate and use catalog resources that currently exist or are in development. We are working with the USGS National Geologic Map Database's existing map catalog, with the USGS National Geological and Geophysical Data Preservation Program, which is developing a metadata catalog (National Digital Catalog) for geoscience information resource discovery, and with the GEON catalog. Existing interchange formats will be used, such as GeoSciML, ChemML, and Open Geospatial Consortium sensor, observation and measurement MLs. Client application development will be fostered by collaboration with industry and academic partners. The GIN project will focus on the remaining aspects of the system -- service definitions and assistance to data providers to implement the services and bring content online - and on system integration of the modules. Initial formal collaborators include the OneGeology-Europe consortium of 27 nations that is building a comparable network under the EU INSPIRE initiative, GEON, Earthchem, and GIS software company ESRI

  8. Archaeal orthologs of Cdc45 and GINS form a stable complex that stimulates the helicase activity of MCM.

    Science.gov (United States)

    Xu, Yuli; Gristwood, Tamzin; Hodgson, Ben; Trinidad, Jonathan C; Albers, Sonja-Verena; Bell, Stephen D

    2016-11-22

    The regulated recruitment of Cdc45 and GINS is key to activating the eukaryotic MCM(2-7) replicative helicase. We demonstrate that the homohexameric archaeal MCM helicase associates with orthologs of GINS and Cdc45 in vivo and in vitro. Association of these factors with MCM robustly stimulates the MCM helicase activity. In contrast to the situation in eukaryotes, archaeal Cdc45 and GINS form an extremely stable complex before binding MCM. Further, the archaeal GINS•Cdc45 complex contains two copies of Cdc45. Our analyses give insight into the function and evolution of the conserved core of the archaeal/eukaryotic replisome.

  9. Victory Gin Lane. Starvation and Beverages in Orwell’s Nineteen Eighty-Four

    Directory of Open Access Journals (Sweden)

    Paolo Caponi

    2015-05-01

    Full Text Available Gin is an ubiquitous presence in the domestic and urban scenery of Nineteen Eighty-Four (1949. For a population mercilessly hungered, it represents a handy and cheap commodity item providing a fluid opportunity for social aggregation. Victory Gin, served “in handless chine mugs” (53, is part of the workers’ staple diet at the Ministry of Truth, and is sold “at ten cents the large nip” from the small bar (actually, “a mere hole in the wall”, 51 in the canteen; served with cloves, it is the “speciality” (79 of that disreputable place which is the Chestnut Tree Café, where Winston Smith once spotted three fallen-out-of-favor members of the Inner Party – Jones, Aaronson and Rutherford – drink it silently after their release from Oceania prison camps (79. As is typical of the fate of spirits in literature, gin also serves as self-medication and can fuel a kind of inner escapism. It is to make the world “look more cheerful” that Winston gulps it down “like a dose of medicine”, and only after the “shock” of swallowing it can he squeeze himself into his alcove and begin his diary (7; gin clears out Winston’s stomach (53, and is the ultima ratio against that prescient “dull ache” in his belly (105; 106 that originates after bumping into “the girl with dark hair” (later: Julia one evening outside Mr. Charrington’s shop.

  10. Prospective systematic review registration: perspective from the Guidelines International Network (G-I-N

    Directory of Open Access Journals (Sweden)

    Van der Wees Philip

    2012-02-01

    Full Text Available Abstract Clinical practice and public health guidelines are important tools for translating research findings into practice with the aim of assisting health practitioners as well as patients and consumers in health behavior and healthcare decision-making. Numerous programs for guideline development exist around the world, with growing international collaboration to improve their quality. One of the key features in developing trustworthy guidelines is that recommendations should be based on high-quality systematic reviews of the best available evidence. The review process used by guideline developers to identify and grade relevant evidence for developing recommendations should be systematic, transparent and unbiased. In this paper, we provide an overview of current international developments in the field of practice guidelines and methods to develop guidelines, with a specific focus on the role of systematic reviews. The Guidelines International Network (G-I-N aims to stimulate collaboration between guideline developers and systematic reviewers to optimize the use of available evidence in guideline development and to increase efficiency in the guideline development process. Considering the significant benefit of systematic reviews for the guideline community, the G-I-N Board of Trustees supports the international prospective register of systematic reviews (PROSPERO initiative. G-I-N also recently launched a Data Extraction Resource (GINDER to present and share data extracted from individual studies in a standardized template. PROSPERO and GINDER are complementary tools to enhance collaboration between guideline developers and systematic reviewers to allow for alignment of activities and a reduction in duplication of effort.

  11. Prospective systematic review registration: perspective from the Guidelines International Network (G-I-N).

    Science.gov (United States)

    Van der Wees, Philip; Qaseem, Amir; Kaila, Minna; Ollenschlaeger, Guenter; Rosenfeld, Richard

    2012-02-09

    Clinical practice and public health guidelines are important tools for translating research findings into practice with the aim of assisting health practitioners as well as patients and consumers in health behavior and healthcare decision-making. Numerous programs for guideline development exist around the world, with growing international collaboration to improve their quality. One of the key features in developing trustworthy guidelines is that recommendations should be based on high-quality systematic reviews of the best available evidence. The review process used by guideline developers to identify and grade relevant evidence for developing recommendations should be systematic, transparent and unbiased. In this paper, we provide an overview of current international developments in the field of practice guidelines and methods to develop guidelines, with a specific focus on the role of systematic reviews. The Guidelines International Network (G-I-N) aims to stimulate collaboration between guideline developers and systematic reviewers to optimize the use of available evidence in guideline development and to increase efficiency in the guideline development process. Considering the significant benefit of systematic reviews for the guideline community, the G-I-N Board of Trustees supports the international prospective register of systematic reviews (PROSPERO) initiative. G-I-N also recently launched a Data Extraction Resource (GINDER) to present and share data extracted from individual studies in a standardized template. PROSPERO and GINDER are complementary tools to enhance collaboration between guideline developers and systematic reviewers to allow for alignment of activities and a reduction in duplication of effort.

  12. Ginés Pérez y su O Crux

    Directory of Open Access Journals (Sweden)

    Climent, José

    2002-12-01

    Full Text Available The exact names attributed to Ginés Pérez were never at all clear. His first appointment to the Cathedral in Valencia complicated matters even more when he was referred to with the Christian name of what appeared to be "Juan", which only added to the confusion as it lead us to believe that he was the only candidate to apply for that position. Today, however, we now know his true and full names: he was called Ginés Pérez de la Parra. We also know, for the first time, the exact date of his death. The quality of his compositions not only contributed to their popularity but gave rise to the works of other composers being attributed to him. The authorship of the majority of his compositions are considered anonymous, though they can be located in diverse archives. Even so, we cannot find a single copy of the O Crux attributed to his name, despite the numerous copies and their variants that abound in Region of Valencia.El nombre de Ginés Pérez nunca ha tenido la claridad de debía. Su primer nombramiento en la catedral de Valencia ya lo confunde añadiéndole el “Juan” lo que ya siembra confusión, además de sugerirnos que, posiblemente, fue llamado para ocupar el puesto sin oposición. Hoy conocemos toda su filiación: Ginés Pérez de la Parra, así como la fecha de su muerte, totalmente equivocada hasta ahora. La valía de sus composiciones motivó, además de la difusión de su obra, la atribución de composiciones de otros autores. La mayor parte de sus composiciones constan como "anónimos", si bien pueden encontrarse en distintos archivos. Del presente O crux, sin embargo, no hemos podido encontrar ninguna copia con su nombre, pese a las múltiples copias, con sus variantes, existentes en la Comunidad Valenciana.

  13. The GIN legal problems of multi-parties at the drill site

    International Nuclear Information System (INIS)

    Case, C.W.

    1991-01-01

    The presence of multiple parties working at a drilling site complicates the application of the environmental laws, rules and regulations. A critical decision prior to any physical activities needs to be made as to which person (i.e., company, partnership) will be charged with the obligation of being the designated Generator of hazardous waste for that site. This critical decision is dictated by the refusal of the EPA to assign more than one EPA Generator Identification Number (GIN) to a single drilling site. The decision as to which member of the multiple parties presence at the drill site will obtain the GIN has liability ramifications when a mistake is made in the cleanup of spilled hazardous waste or hazardous substances; an improper situation arises as to the transportation, storage, treatment and disposal of hazardous waste; the waste is improperly classified, or the biennial reporting of hazardous waste activities does not occur. Liability issues arise that go far beyond the ordinary contractual disputes seen in the past arising from drilling activities, with liability in some situations well in excess of any damage claims normally allowed under common law or statutory law in the State of Texas for non-environmental disputes. This paper reviews the liabilities and responsibilities of oil and gas drillers under the Resource Conservation and Recovery Act and the Comprehensive Environmental Response, Compensation and Liability Act

  14. Development of cotton gin PM10 emission factors for EPA’s AP-42-DUPLICATE DO NOT USE

    Science.gov (United States)

    The Compilation of Air Pollution Emission Factors (AP-42) emission factors are assigned ratings, from A (Excellent) to E (Poor), based on the quality of data used to develop them. All current PM10 cotton gin emission factors received quality ratings of D or lower. In an effort to improve these ratin...

  15. A simulated approach to estimating PM10 and PM2.5 concentrations downwind from cotton gins

    Science.gov (United States)

    Cotton gins are required to obtain operating permits from state air pollution regulatory agencies (SAPRA), which regulate the amount of particulate matter that can be emitted. Industrial Source Complex Short Term version 3 (ISCST3) is the Gaussian dispersion model currently used by some SAPRAs to pr...

  16. Biological control agent of larger black flour beetles (Coleoptera: Tenebrionidae): A nuisance pest developing in cotton gin trash piles.

    Science.gov (United States)

    Larger black flour beetles (LBFB), Cynaeus angustus, feed on saprophytic fungi found in gin trash piles, and become nuisance pests in homes and businesses. We examined the dose-response of three entomopathogenic nematode species (Steinernema carpocapsae, S. feltiae, and Heterorhabditis bacteriophora...

  17. A review of the effects of ginning practices on cotton fibre and yarn properties and processing performance

    CSIR Research Space (South Africa)

    Sanderson, KW

    1985-08-01

    Full Text Available Over the years, since the first formal cotton ginning experiments were conducted by the United State department of agriculture in 1962, a large volume of literature, from research papers to popular articles, has been published on the effect...

  18. Non-contact image processing for gin trash sensors in stripper harvested cotton with burr and fine trash correction

    Science.gov (United States)

    This study was initiated to provide the basis for obtaining online information as to the levels of the various types of gin trash. The objective is to provide the ginner with knowledge of the quantity of the various trash components in the raw uncleaned seed cotton. This information is currently not...

  19. Per preparare la ripresa: Progetto europeo GI-N2K, “Geographic Information – Need to Know”

    Directory of Open Access Journals (Sweden)

    Mauro Salvemini

    2014-02-01

    Full Text Available The GI-N2K project, coordinated by the Katholieke Universiteit Leuven, which began in October 2013, and formed by an international consortium of 31 partners (25  countries is funded by the Erasmus Lifelong Learning Programme, aims to reformulate  the Body of Knowledge in the field of Geographic Information Science and  Technology.

  20. EVALUATION OF GIN WASTE AS A GROWING SUBSTRATE, ENRICHED WITH DIFFERENT VOLUME PERCENTAGE OF THE WHEAT BRAN FOR CULTIVATION OF OYSTER MUSHROOM (PLEUROTUS OSTREATUS

    Directory of Open Access Journals (Sweden)

    M. M. Akhtar

    2016-08-01

    Full Text Available Pleurotusostreatus mushroom was cultivated on cotton gin waste amended with wheat bran in order to judge its growth potential. Two substrates (cotton gin waste and wheat bran were employed alone and with different combinations. Experiment consisted of four treatments T0 (100 % cotton gin waste, T1(97% cotton gin waste + 3% wheat bran, T2(94% cotton gin waste + 6% wheat bran and T3(91% cotton gin waste + 9% wheat bran. Data about time needed for commencement of spawn run, time needed for completion of mycelial growth, time needed for initiation of pinheads, time needed for harvesting of 1st, 2nd and 3rd flush, fresh weight of 1st, 2nd and 3rd flush harvested, total yield, pH of mushroom, total soluble solids of mushroom, acidity and ascorbic acid contents, reducing sugars, non-reducing sugars and total sugars of mushroom, total nitrogen, phosphorus and potassium contents of mushroom was recorded. T0 (100 % cotton gin waste performed better as compared to other treatments.

  1. Exposição a fungos dos trabalhadores dos ginásios com piscina

    OpenAIRE

    Viegas, Carla Sofia Costa

    2010-01-01

    RESUMO - Os trabalhadores dos ginásios com piscinas apresentam maior prevalência de lesões fúngicas, como a Tinea pedis e a onicomicose, devido às características intrínsecas da sua actividade profissional, pois apresentam mais horas por dia de exposição à contaminação fúngica das superfícies. Esta situação verifica-se não só por serem os que mais frequentam os locais possíveis de estarem contaminados, como é o caso de balneários, vestiários e zona envolvente às piscinas, mas t...

  2. “Ginasticando”: parcerias e possibilidades da Ginástica na comunidade

    Directory of Open Access Journals (Sweden)

    PRISCILA LOPES

    2016-06-01

    Full Text Available O Projeto de Extensão “Ginasticando” tem como meta disseminar a Ginástica em Diamantina, MG. Tendo início em 2011, teve seus objetivos e metodologias modificadas de acordo com as demandas da região, diagnosticadas por meio de estudos e pesquisas na área da Educação Física escolar. Os principais resultados alcançados até o momento apontam para a necessidade de continuidade do projeto no sentido de contribuir para a ampliação do repertório de práticas corporais vivenciadas no ambiente escolar.

  3. Standing footprint diagnostic method

    Science.gov (United States)

    Fan, Y. F.; Fan, Y. B.; Li, Z. Y.; Newman, T.; Lv, C. S.; Fan, Y. Z.

    2013-10-01

    Center of pressure is commonly used to evaluate standing balance. Even though it is incomplete, no better evaluation method has been presented. We designed our experiment with three standing postures: standing with feet together, standing with feet shoulder width apart, and standing with feet slightly wider than shoulder width. Our platform-based pressure system collected the instantaneous plantar pressure (standing footprint). A physical quantity of instantaneous standing footprint principal axis was defined, and it was used to construct an index to evaluate standing balance. Comparison between results from our newly established index and those from the center of pressure index to evaluate the stability of different standing postures revealed that the standing footprint principal axis index could better respond to the standing posture change than the existing one. Analysis indicated that the insensitive response to the relative position between feet and to the standing posture change from the center of pressure could be better detected by the standing footprint principal axis index. This predicts a wide application of standing footprint principal axis index when evaluating standing balance.

  4. Lesões desportivas na ginástica artística: estudo a partir de morbidade referida

    OpenAIRE

    Hoshi,Rosangela Akemi; Pastre,Carlos Marcelo; Vanderlei,Luiz Carlos Marques; Netto Júnior,Jayme; Bastos,Fábio do Nascimento

    2008-01-01

    INTRODUÇÃO: Os níveis de exigência biomecânica devidos ao alto grau de dificuldade na realização de gestos fazem da ginástica artística (GA) uma modalidade com elevado risco de lesões. Assim, é necessário que os aspectos a elas relacionados sejam controlados. OBJETIVO: Analisar a ocorrência de lesões na Ginástica Artística, associando-as a fatores de risco específicos da modalidade e do atleta, a partir de inquérito de morbidade referida. MÉTODOS: Foram entrevistados 54 ginastas, recrutados a...

  5. Inimhääle lummus ja topeltverism / Tiiu Levald

    Index Scriptorium Estoniae

    Levald, Tiiu, 1940-

    2008-01-01

    Birgitta festivali raames 10. ja 11. VIII Pirita kloostris toimunud etendustest - Mascagni "Talupoja au", Leoncavallo "Pajatsid" ja Donizetti "Maria Stuart" Moskva Novaja Opera esituses, dirigendid: Eri Klas, Valeri Kritskov ja Sergei Lõssenko

  6. Resolução temporal: desempenho de escolares no teste GIN - Gaps-in-noise Temporal resolution: performance of school-aged children in the GIN - Gaps-in-noise test

    Directory of Open Access Journals (Sweden)

    Maria Isabel Ramos do Amaral

    2010-12-01

    Full Text Available A habilidade auditiva denominada resolução temporal consiste no tempo mínimo necessário para resolver eventos acústicos, sendo fundamental para a compreensão de fala, e pode ser avaliada por testes de detecção de gaps, dentre eles o teste GIN - Gaps In Noise. OBJETIVO: Verificar o desempenho da resolução temporal em crianças sem queixas auditivas e/ou dificuldades escolares, no teste GIN, considerando-se o gênero masculino e feminino e a faixa etária de 8, 9 e 10 anos. FORMA DO ESTUDO: Coorte contemporânea com corte transversal prospectivo. MATERIAL E MÉTODO: O teste GIN foi aplicado em 75 escolares, reunidos em três grupos por faixa etária. RESULTADOS: Não foram encontradas diferenças significantes em relação às variáveis orelha e faixa etária. O gênero masculino obteve desempenho levemente melhor do que o feminino em relação apenas à porcentagem de acertos. CONCLUSÃO: A média do limiar de detecção de gaps e porcentagem de acertos foram calculados independente das variáveis orelha, gênero e faixa etária, sendo encontrados os valores de 4,7ms e 73,6%. Baseado no critério de intervalo de confiança 95% como corte para normalidade, os valores do limiar de detecção de gap e porcentagem de acertos foram 6,1ms e 60%, respectivamente.Time resolution hearing skill is the minimum time necessary to solve acoustic events, which is fundamental for speech understanding, and which may be assessed by gap-detection tests, such as the Gaps-in-noise test (GIN. AIM: the purpose of this study was to verify the performance of time processing ability in children with no hearing and/or education difficulties by applying the GIN test in both genders and ages from 8 to 10 years. STUDY DESIGN: a prospective cross-sectional contemporary cohort. MATERIAL AND METHOD: The GIN test was applied to 75 school-aged children separated into three groups by age. RESULTS: The findings showed no statistical differences among age groups or ears

  7. The Cdc45/RecJ-like protein forms a complex with GINS and MCM, and is important for DNA replication in Thermococcus kodakarensis.

    Science.gov (United States)

    Nagata, Mariko; Ishino, Sonoko; Yamagami, Takeshi; Ogino, Hiromi; Simons, Jan-Robert; Kanai, Tamotsu; Atomi, Haruyuki; Ishino, Yoshizumi

    2017-10-13

    The archaeal minichromosome maintenance (MCM) has DNA helicase activity, which is stimulated by GINS in several archaea. In the eukaryotic replicative helicase complex, Cdc45 forms a complex with MCM and GINS, named as CMG (Cdc45-MCM-GINS). Cdc45 shares sequence similarity with bacterial RecJ. A Cdc45/RecJ-like protein from Thermococcus kodakarensis shows a bacterial RecJ-like exonuclease activity, which is stimulated by GINS in vitro. Therefore, this archaeal Cdc45/RecJ is designated as GAN, from GINS-associated nuclease. In this study, we identified the CMG-like complex in T. kodakarensis cells. The GAN·GINS complex stimulated the MCM helicase, but MCM did not affect the nuclease activity of GAN in vitro. The gene disruption analysis showed that GAN was non-essential for its viability but the Δgan mutant did not grow at 93°C. Furthermore, the Δgan mutant showed a clear retardation in growth as compared with the parent cells under optimal conditions at 85°C. These deficiencies were recovered by introducing the gan gene encoding the nuclease deficient GAN protein back to the genome. These results suggest that the replicative helicase complex without GAN may become unstable and ineffective in replication fork progression. The nuclease activity of GAN is not related to the growth defects of the Δgan mutant cells. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

  8. Planter unit test stand

    Science.gov (United States)

    A planter test stand was developed to evaluate individual row-crop metering units in early 2013. This test stand provided the ability to quantify actual seed metering in terms of population, seed spacing, skips, and multiples over a range of meter RPMs and vacuum pressures. Preliminary data has been...

  9. Imagens da prática profissional em academias de ginástica na cidade do Rio de Janeiro

    Directory of Open Access Journals (Sweden)

    Carlos Alberto de Andrade Coelho Filho

    2010-05-01

    Full Text Available O objetivo deste estudo é fornecer subsídios aos cursos de educação física, aproximando a formação profissional do campo de atuação em academias de ginástica. Através da análise de discurso, descrevemos e interpretamos a maneira como o profissional apresenta a si mesmo e a sua prática às outras pessoas, os meios pelos quais dirige e regula a impressão que formam a seu respeito e as atividades que pode ou não realizar. Os resultados confirmam que a prática do profissional de ginástica em academia vive momentos de tensão e impasse, o que implica a urgência de reformular a formação para essa prática nos cursos de graduação e de pós-graduação em educação física

  10. Battery condenser system PM2.5 emission factors and rates for cotton gins: Method 201A combination PM10 and PM2.5 sizing cyclones

    Science.gov (United States)

    This report is part of a project to characterize cotton gin emissions from the standpoint of stack sampling. In 2006, EPA finalized and published a more stringent standard for particulate matter with nominal diameter less than or equal to 2.5 µm (PM2.5). This created an urgent need to collect additi...

  11. Variable Attitude Test Stand

    Data.gov (United States)

    Federal Laboratory Consortium — The Variable Attitude Test Stand designed and built for testing of the V-22 tilt rotor aircraft propulsion system, is used to evaluate the effect of aircraft flight...

  12. Where We Now Stand

    Science.gov (United States)

    Lumsden, Keith G.

    1969-01-01

    Noting the acceleration of scientific evaluation, the author focuses his attention on where we now stand in the evaluation of two methods of instruction: programed learning materials and television. (Editor)

  13. The Stimulus test stand

    International Nuclear Information System (INIS)

    Christofek, L.; Rapidis, P.; Reinhard, A.; Fermilab

    2005-01-01

    The Stimulus Test Stand was originally constructed and assembled for testing the SVX2 ASIC readout and then upgraded for SVX3 ASIC prototyping and testing. We have modified this system for SVX4 ASIC [1] prototype testing. We described the individual components below. Additional details for other hardware for SVX4 testing can be found in reference [2]. We provide a description of the Stimulus Test Stand used for prototype testing of the SVX4 chip

  14. System Simulation by Recursive Feedback: Coupling a Set of Stand-Alone Subsystem Simulations

    Science.gov (United States)

    Nixon, D. D.

    2001-01-01

    Conventional construction of digital dynamic system simulations often involves collecting differential equations that model each subsystem, arran g them to a standard form, and obtaining their numerical gin solution as a single coupled, total-system simultaneous set. Simulation by numerical coupling of independent stand-alone subsimulations is a fundamentally different approach that is attractive because, among other things, the architecture naturally facilitates high fidelity, broad scope, and discipline independence. Recursive feedback is defined and discussed as a candidate approach to multidiscipline dynamic system simulation by numerical coupling of self-contained, single-discipline subsystem simulations. A satellite motion example containing three subsystems (orbit dynamics, attitude dynamics, and aerodynamics) has been defined and constructed using this approach. Conventional solution methods are used in the subsystem simulations. Distributed and centralized implementations of coupling have been considered. Numerical results are evaluated by direct comparison with a standard total-system, simultaneous-solution approach.

  15. Economics of stand management

    Science.gov (United States)

    David K. Lewis

    1986-01-01

    This paper sets out to demonstrate the importance of considering the wealth represented by the growing stock in economic analyses of stand management alternatives, and to demonstrate the role of thinning in the manipulation of the efficiency of growing stock in the management of shortleaf pine (Pinus echinata Mill.). These goals are achieved through a demonstration of...

  16. Principles of managing stands

    Science.gov (United States)

    David A. Marquis; Rodney Jacobs

    1989-01-01

    Forest stands are managed to achieve some combination of desired products or values. These products or values may include income and tangible benefits from timber production or fees for hunting rights and other recreational activities. The values may be intangible, such as the enjoyment of seeing wildlife or flowering plants, or the simple satisfaction of knowing that...

  17. Reflexões sobre o trabalho do psicólogo do esporte em uma academia de ginástica

    Directory of Open Access Journals (Sweden)

    Livia Gomes Viana-Meireles

    2015-11-01

    Full Text Available http://dx.doi.org/10.5007/2175-8042.2015v27n46p171 O presente estudo buscou desenvolver uma reflexão sobre a prática do psicólogo do esporte dentro de uma academia de ginástica a partir do relato de experiência de estágio em psicologia. Foi realizada uma pesquisa com alunos e professores que possibilitou a contextualização do ambiente da academia e o planejamento das atividades a serem realizadas. A experiência de estágio possibilitou o início de uma reflexão sobre o campo de atuação do psicólogo do esporte nas academias de ginástica apontando ricas possibilidades para ações e intervenções em diferentes contextos que envolvam atividade física.

  18. Production cross sections and isomeric ratios for sup(110m)In/sup(110g)In formed in Cd (d,xn) reactions

    International Nuclear Information System (INIS)

    Herreros Usher, Oscar; Maceiras de Jefimowicz, Elena; De la Vega Vedoya, Mario; Jorge Nassiff, Sonia

    1980-01-01

    Excitation functions and isomeric cross sections ratios have been measured for the 110 Cd (d,2n) and 111 Cd (d,3n) reactions in which the isomeric pair sup(110m)In/sup(110g)In is produced. Activation method was employed and the irradiations were performed at the synchrocyclotron of the Comision Nacional de Energia Atomica, Argentina, with an incident energy of 27.MeV. (author) [es

  19. Take a Stand!

    DEFF Research Database (Denmark)

    Danquah, I. H.; Kloster, S.; Holtermann, A.

    2017-01-01

    workers in total) were cluster randomized for intervention or control. The intervention included the appointment of local ambassadors, management support, environmental changes, a lecture and a workshop. Sitting time was measured using an ActiGraph GT3X+ fixed on the thigh. Data were processed using Acti4......Background: Prolonged sitting time has been associated with adverse health outcomes. Interventions at work may contribute to reduced sitting. The objective was to test if a multicomponent work-based intervention can reduce sitting time and the number of prolonged sitting periods (> 30 min......), increase the number of sit-to-stand transitions and decrease waist circumference and body fat percentage among office workers. Primary outcomes were: change in sitting time, prolonged sitting periods and sit-to-stand transitions at followup 1 month later. Methods: At four workplaces, 19 offices (317...

  20. Stand-alone XLIF

    DEFF Research Database (Denmark)

    Hansen, E. J.; Simony, A.; Hummel, Stefan

    2015-01-01

    and clinical/radiological results in 22 patients treated with XLIF procedure for DS or degenerative disc disease (DDD). Material and methods: 22 consecutive patients with DS underwent surgery with the XLIF stand-alone procedure, with follow-up of 24 months. Clinical outcome scores were collected. Complications......Introduction: Adult thoracolumbar degeneration is an increasing challenge in the aging population. With age the progressive degeneration of the discs leads to an asymmetric collapse and a thoracolumbar coronal plane deformity, a degenerative scoliosis (DS). Aim: To evaluate the complication rate......-year follow-up, with a 31.8% revision rate. Due to the high revision rate we recommend supplementary posterior instrumentation, to achieve a higher fusion rate. When considering XLIF-stand-alone procedure for DS or DDD without supplemental posterior instrumentation, only single-level disease should...

  1. Standing wave accelerating structures

    International Nuclear Information System (INIS)

    Zavadtsev, A.A.; Zverev, B.V.; Sobepin, N.P.

    1984-01-01

    Accelerating ELA structures are considered and chosen for applied purposes of special designation. Accelerating structures with the standing wave are considered most effective for small size ELA. Designs and results of experimental investigation of two new accelerating structures are described. These are structures of the ''ring'' type with a decreased number of excitinq oscillation types and strucuture with transverse rods with a twice smaller transverse size as compared with the biperiodical structure with internal connection resonators. The accelerating biperiodical structures of the conventional type by the fact that the whole structure is not a linear chain of connected resonators, but a ring one. Model tests have shown that the homogeneous structure with transverse rods (STR) at the frequency of 2.8 GHz in the regime of the standing wave has an effective shunt resistance equalling 23 MOhm/m. It is shown that the small transverse size of biperiodic STR makes its application in logging linear electron accelerators

  2. Modelling and Predicting the Breaking Strength and Mass Irregularity of Cotton Rotor-Spun Yarns Containing Cotton Fiber Recovered from Ginning Process by Using Artificial Neural Network Algorithm

    Directory of Open Access Journals (Sweden)

    Mohsen Shanbeh

    2011-01-01

    Full Text Available One of the main methods to reduce the production costs is waste recycling which is the most important challenge for the future. Cotton wastes collected from ginning process have desirable properties which could be used during spinning process. The purpose of this study was to develop predictive models of breaking strength and mass irregularity (CV% of cotton waste rotor-spun yarns containing cotton waste collected from ginning process by using the artificial neural network trained with backpropagation algorithm. Artificial neural network models have been developed based on rotor diameter, rotor speed, navel type, opener roller speed, ginning waste proportion and yarn linear density as input parameters. The parameters of artificial neural network model, namely, learning, and momentum rate, number of hidden layers and number of hidden processing elements (neurons were optimized to get the best predictive models. The findings showed that the breaking strength and mass irregularity of rotor spun yarns could be predicted satisfactorily by artificial neural network. The maximum error in predicting the breaking strength and mass irregularity of testing data was 8.34% and 6.65%, respectively.

  3. Fluidized bed gasification of high tonnage sorghum, cotton gin trash and beef cattle manure: Evaluation of synthesis gas production

    International Nuclear Information System (INIS)

    Maglinao, Amado L.; Capareda, Sergio C.; Nam, Hyungseok

    2015-01-01

    Highlights: • High tonnage sorghum, cotton gin trash and beef cattle manure were characterized and gasified in a fluidized bed reactor. • Biomass gasification at 730 °C and ER = 0.35 produced synthesis gas with an average energy content of 4.19 MJ Nm −3 . • Synthesis gas heating value and yield were relatively constant at reaction temperatures from 730 °C to 800 °C. • Optimum hydrogen production on HTS gasification was achieved at 780 °C temperature and ER of 0.4. - Abstract: Fluidized bed gasification using high-tonnage sorghum, cotton gin trash and beef cattle manure was performed in a pilot scale bubbling fluidized bed reactor equipped with the necessary feedback control system. Characterization of biomass showed that the high-tonnage sorghum had the highest energy and carbon content of 19.58 MJ kg −1 and 42.29% wt , respectively among the three feed stocks. At 730 °C reaction temperature and equivalence ratio of 0.35, comparable yields of methane, nitrogen and carbon dioxide (within ± 1.4% vol ) were observed in all three feed stocks. The gasification system produced synthesis gas with an average heating value of 4.19 ± 0.09 MJ Nm −3 and an average yield of 1.98 ± 0.1 Nm 3 kg −1 of biomass. Carbon conversion and gasification efficiencies indicated that most of the carbon was converted to gaseous products (85% average ) while 48% average of the energy from the biomass was converted into combustible gas. The production of hydrogen was significantly affected by the biomass used during gasification. The synthesis gas heating value and yield were relatively constant at reaction temperatures from 730 °C to 800 °C. Utilizing high-tonnage sorghum, the optimum hydrogen production during gasification was achieved at a reaction temperature of 780 °C and an equivalence ratio of 0.40.

  4. Multi-Purpose Test Stand

    Data.gov (United States)

    Federal Laboratory Consortium — The Multi-Purpose Test Stand is used for a wide variety of tests. The Stand is designed to be rotated through a range of fixed yaw positions to allow engines to be...

  5. Motivos de abandono na prática de ginástica artística no contexto extracurricular

    Directory of Open Access Journals (Sweden)

    Priscila LOPES

    Full Text Available Resumo O Esporte consiste na principal opção para a prática de atividades físicas entre as crianças e os jovens. Apesar do grande interesse desse público às práticas esportivas, a literatura aponta alto índice de abandono. Motivados por essa conjuntura, o objetivo desse estudo foi verificar o motivo de abandono, mais especificamente, na prática de Ginástica Artística (GA no contexto das atividades extracurriculares. Entrevistamos praticantes meninas de GA que apresentavam histórico de abandono dessa prática esportiva por determinado período de tempo. Para o tratamento dos dados, optamos pela Análise de Conteúdo proposta por BARDIN. Constatamos que fatores intrínsecos e extrínsecos estão vinculados ao processo de abandono da prática desse esporte. Entretanto, os fatores extrínsecos sobrepuseram àqueles intrínsecos, o que evidencia que o ambiente e as condições situacionais e interpessoais exercem maior influência sobre o afastamento das ginastas. Assim, ressaltamos a importância da atenção dos profissionais a esses aspectos para garantir que as atividades atendam às necessidades e aos anseios das ginastas.

  6. Ginástica Laboral: efeitos de um programa de ginástica laboral sobre a flexibilidade em trabalhadores de diversos setores de um hospital de ensino da região do Vale do Rio Pardo/RS

    Directory of Open Access Journals (Sweden)

    Andréa Mattos de Andrade

    2015-12-01

    Full Text Available A Ginástica Laboral (GL é uma atividade física realizada durante a jornada de trabalho, com exercício de compensação aos movimentos repetitivos, à ausência de movimentos, ou a posturas desconfortáveis assumidas durante o período de trabalho. Objetivo: verificar possíveis efeitos de um programa de GL sobre a flexibilidade em trabalhadores de diversos setores de um hospital de ensino da região do Vale do Rio Pardo/RS. Método: estudo semi-experimental realizado em diversos setores de um hospital, de março de 2014 a maio 2015, em que foram avaliados 42 indivíduos, do sexo feminino, com idade entre 22 e 58 anos, que participavam do programa de GL. Para a coleta de dados, foi aplicado o teste sentar e alcançar (sit and reach e o teste do manguito rotador (ombro direito e esquerdo em três momentos: 1 (antes da intervenção com GL; 2 (logo após o término da intervenção e 3 (quatro meses, após a intervenção. Resultados: a flexibilidade diferiu na comparação entre os momentos 1 e 2 e entre os momentos 1 e 3, em todos os testes aplicados, demonstrando que o programa de GL melhorou os níveis de flexibilidade dos trabalhadores. Não foi observada diferença significativa entre os momentos 2 e 3. Considerações finais: o programa de GL melhorou os níveis de flexibilidade dos trabalhadores, mantendo esses níveis semelhantes seis meses após o término da intervenção.

  7. ISSP Position Stand

    DEFF Research Database (Denmark)

    Ryba, Tatiana; Stambulova, Natalia; Si, Gangyan

    2013-01-01

    The multicultural landscape of contemporary sport sets a challenge to rethink sport and exercise psychology research and practice through a culturally re␣exive lens. This ISSP Position Stand provides a rigorous synthesis and engagement with existing scholarship to outline a roadmap for future work...... in the ␣eld. The shift to culturally competent sport and exercise psychology implies: (a) recognizing hidden ethnocentric philosophical assumptions permeating much of the current theory, research, and practice; (b) transitioning to professional ethics in which difference is seen as not inherent and ␣xed...... but as relational and ␣uid; and (c) focusing on meaning (instead of cause) in cross-cultural and cultural research projects, and cultural praxis work. In the paper, we ␣rst provide an overview of the concepts of cultural competence and ethics of difference. Second, we present a step-by-step approach for developing...

  8. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2009-01-01

    Ordinary Meeting on 11 May 2009 The meeting of the Standing Concertation Committee held on 11 May 2009 was entirely dedicated to the preparation of the TREF meeting on 19 & 20 May 2009. The Committee took note, discussed and agreed on some clarifications on a number of documents and presentations that the Management planned to submit and/or present to TREF on the following subjects: • Personnel statistics 2008: J. Purvis presented the Personnel Statistics for 2008 prepared by HR Department. In line with the previous year, key messages were firstly, a general reduction in staff (2544 to 2400, - 6%), secondly, a reduction in administrative services personnel (from 422 to 387, - 8%) and thirdly, a marked increase in the number of Users and Unpaid Associates (from 8369 to 9140, + 9%) • Five-Yearly Review 2010: A series of draft documents were submitted for discussion, comprising an introductory document explaining the statutory basis for the following four document...

  9. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2009-01-01

    The main items discussed at the meetings of the Standing Concertation Committee in the first quarter of 2009 included: Merit Appraisal and Recognition Scheme (MARS) 2009 exercise The committee took note of 2009 MARS ceiling guidelines giving the advancement budget by career path and amounting to approx 1.80% of the basic salary bill. To this will be added 250 steps CERN-wide, financed by savings from implementation of the international indemnity for 2007, 2008 and the first half of 2009. The specific Senior Staff Guidelines, including the proposed number of promotions from Career Path E to F, were also noted. The guidelines with respect to step distribution were also noted: the minima and maxima remain the same as in previous years. Compliance with the guidelines will continue to be monitored closely (more details, including a frequently asked questions section). It was also noted that Financial Awards (awards for extraordinary service and responsibility allowances) may b...

  10. Standing Concertation Committee

    CERN Document Server

    HR Department

    2010-01-01

    Main issues examined at the meeting of 2 October 2009 The October 2009 meeting of the Standing Concertation Committee was entirely devoted to preparation of TREF’s meeting on 21-22 October. The Committee took note of, discussed and agreed on clarifications needed to some of the documents and presentations that the Management intended to submit and/or present to TREF on the following subjects: Equal opportunities The Committee took note of a preliminary report on equal opportunities at CERN drawn up by D. Chromek-Burckhart, the Equal Opportunities Officer, and T. Smith, Chairman of the Equal Opportunities Advisory Panel, containing in particular a proposal for a new process for resolving harassment conflicts. Technical analysis of the CERN Health Insurance Scheme - Actuary’s Report The Committee took note of a presentation by P. Charpentier, Chairman of the CERN Health Insurance Supervisory Board (CHIS Board), on the 2009 actuarial report on the CERN Health Insurance Scheme (CHIS). Th...

  11. Standing Concertation Commmittee

    CERN Document Server

    HR Department

    2007-01-01

    Ordinary meeting on 2 november 2007 Extraordinary meeting on 12 November 2007 The main items discussed at the meetings of the Standing Concertation Committee on 2 November 2007 and 12 November included: Restaurants Supervisory Committee Report The committee took note of the report by the chairman of the Restaurants Supervisory Committee (RSC), T. Lagrange. In particular, it was recorded that, in Restaurant No. 1, the new kitchen and free flow arrangements had been inaugurated and all works had been commissioned on schedule in October 2007.The contractor, Novae, had taken over maintenance of the new kitchen. Some price increases were to be expected in the coming months due mainly to strong increases in the cost of basic ingredients. A problem with bad smells in the area of Restaurant No. 1 was being taken care of by tuning the ventilation system. The RSC wished to thank the management and staff of Restaurant No. 2 for their cooperation while Restaurant No 1 was ...

  12. STANDING CONCERTATION COMMMITTEE

    CERN Multimedia

    HR Department

    2008-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2008 The main items discussed at the meetings of the Standing Concertation Committee on 27 February 2008 included: Short-term Saved Leave Scheme The committee noted that, by the end of February 2008, some 600 staff had subscribed to the short-term saved leave scheme: approx 58% had subscribed 1 slice, 14% two slices, 5% three slices and 23% four slices. Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme The committee agreed to recommend Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme to the Director-General for approval. Administrative Circular No. 30 (Rev. 2) - Financial benefits upon taking up appointment and termination of contract The committee agreed to recommend Administrative Circular No. 30 (Rev. 2) - Financial Benefits upon taking up appointment and termination of contract to the Director-General for approval. Progressive Retirement Programme The Progressive Retirement Programme (PRP) was extended for a further year to 3...

  13. Standing Concertation Committee

    CERN Document Server

    HR Department

    2008-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2008 The main items discussed at the meetings of the Standing Concertation Committee on 27 February 2008 included: Short-term Saved Leave Scheme The Committee noted that, by the end of February 2008, some 600 staff had enrolled in the short-term saved leave scheme: approx. 58% had signed up for 1 slice, 14% for two slices, 5% for three slices and 23% for four slices. Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme The Committee agreed to recommend the Director-General to approve Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme. Administrative Circular No. 30 (Rev. 2) - Financial benefits upon taking up appointment and termination of contract The Committee agreed to recommend the Director-General to approve Administrative Circular No. 30 (Rev. 2) - Financial Benefits upon taking up appointment and termination of contract. Progressive Retirement Programme The Progressive Retirement Programme (PR...

  14. Food Irradiation. Standing legislation

    International Nuclear Information System (INIS)

    Verdejo S, M.

    1997-01-01

    The standing legislation in Mexico on food irradiation matter has its basis on the Constitutional Policy of the Mexican United States on the 4 Th. article by its refers to Secretary of Health, 27 Th. article to the Secretary of Energy and 123 Th. of the Secretary of Work and Social Security. The laws and regulations emanated of the proper Constitution establishing the general features which gives the normative frame to this activity. The general regulations of Radiological Safety expedited by the National Commission for Nuclear Safety and Safeguards to state the specifications which must be fulfill the industrial installations which utilizing ionizing radiations, between this line is founded, just as the requirements for the responsible of the radiological protection and the operation of these establishments. The project of Regulation of the General Health Law in matter of Sanitary Control of Benefits and Services, that in short time will be officialized, include a specific chapter on food irradiation which considers the International Organizations Recommendations and the pertaining harmonization stated for Latin America, which elaboration was in charge of specialized group where Mexico was participant. Additionally, the Secretary of Health has a Mexican Official Standard NOM-033-SSA1-1993 named 'Food irradiation; permissible doses in foods, raw materials and support additives' standing from the year 1995, where is established the associated requirements to the control registers, service constancies and dose limits for different groups of foods, moreover of the specific guidelines for its process. This standard will be adequate considering the updating Regulation of Benefits and Services and the limits established the Regulation for Latin America. The associated laws that cover in general terms it would be the requirements for food irradiation although such term is not manageable. (Author)

  15. Fluvial Export Variability Of Limiting Nutrient Fluxes To The Indian Ocean From Kelani, Kalu and Gin Rivers Of Sri Lanka

    Science.gov (United States)

    Ranasinghage, P. N.; Silva, A. N.; Vlahos, P.

    2016-12-01

    Inorganic `reactive' nutrients hold the highest importance in understanding the role of limiting nutrients in the ocean since they facilitate marine biological productivity and carbon sequestration that would eventually pave the way to regulate the biogeochemical climate feedbacks. Significant inorganic fractions are expected to be exported episodically to the ocean from fluvial fluxes though this is poorly understood. Thus, no considerable amounts of published work regarding the fluxes from Sri Lankan freshwater streams have ever been recorded. A study was carried out to quantify the contribution of Kelani, Kalu and Gin Rivers, three major rivers in the wet zone of Sri Lanka, in exporting major limiting nutrient fluxes to the Indian Ocean; to understand the significance of their variability patterns with rainfall and understand differences in their inputs. The study was conducted during the summer monsoonal period from late August to early November at two-three week intervals where water samples were collected for ammonia, nitrite, nitrate, orthophosphate, silica, sulfate and iron analysis by Colorimetric Spectroscopy. Discharge and rainfall data were retrieved from the Department of Irrigation and Department of Meteorology, Sri Lanka respectively. According to Two Way ANOVA, none of the individual fluxes showed significant differences (p>0.1) both in their temporal and spatial variability suggesting that studied rivers respond similarly in fluvial transportation owing to the similar rainfall intensities observed during the study period in the wet zone. Linear Regression Analysis indicates that only PO43- (p<0.01), SO42- (p<0.01) and NO2-(p<0.01 for Kelani and Kalu; 0.0.1Key words; nutrients, fluvial, fluxes, Redfield ratios

  16. Post-cultural stand dynamics in an abandoned chestnut coppice at its ecological border

    Directory of Open Access Journals (Sweden)

    2006-01-01

    Full Text Available Until the be­ginning of the last century, chestnut has played an important role as staple food and primary wood source. In many cases it was cultivated at the border of its ecological limits where it was planted by man in place of the original and more site-adapted tree species. However, with the abandonment of the rural activities, ma­nagement of chestnut forests was progressively left starting from more marginal areas, usually occupied by coppice stands. After the interruption of the traditional coppice management system (usual rotation periods of 10-25 years, natural intra- and interspecific competition dynamics have become the driving force of the stand evolution. This may lead to dramatic changes in both structure and species composition of the stands. The aim of this study is to analyse the post-cultural evolution of an abandoned chestnut coppice in the Pesio Valley (Piedmont, Italy in order to highlight the competition among different "basic silvi­cultural components" of the forest using a dendroecological approach. The "basic silvicultural components" are intended as the elements defined as groups of trees of the stand that have similar features such as silvi­culturally relevant attributes: species (chestnut, beech, fir, origin (seed, sprout and cultural age and function (standard/reserve, maiden, shoot, regeneration, dead tree. The mean growth curves of the compo­nents show the different fitness of each category. From a general point of view, the beech and fir components show a better competitive potential in comparison with chestnut. Among chestnut components, maidens from seeds reveal a better growth trend compared to coppice shoots and standards.

  17. Transtorno alimentar e variáveis comportamentais relacionadas ao excercício físico em academia de ginástica

    OpenAIRE

    Weis, Andréia

    2013-01-01

    Resumo: O objetivo do estudo foi analisar variáveis comportamentais relacionadas ao exercício físico (compromisso ao exercício físico, modalidades praticadas, objetivos para prática e características de treinamento) em pessoas com transtorno alimentar frenquentadoras de uma academia de ginástica de Balneário Camboriú - SC. Participaram da pesquisa 239 indivíduos, sendo 139 mulheres (32,2, ±11,0 anos) e 100 homens (31,4, ±13,1 anos). Os sujeitos responderam o Teste de Atitudes Alimentares (EAT...

  18. Hipotensão pós-exercício em idosas hipertensas controladas, após uma aula de ginástica localizada

    OpenAIRE

    Silva, Natal da

    2012-01-01

    O presente estudo teve como objetivo avaliar a Hipotensão pós-exercício em idosas hipertensas com pressão arterial controlada por medicamentos anti-hipertensivos, em uma aula de ginástica localizada de intensidade moderada de acordo com a escala de Borg. Para tanto, a amostra foi composta por 13 idosas ativas do CCI (Centro de Convivência do Idoso) do Recanto das Emas/DF, as quais foram aplicadas um questionário contendo 10 questões, com o intuito de conhecer a vida pregressa do indivíduo em ...

  19. Gerenciamento de custos para tomada de decisão - estudo em academia de musculação e ginástica

    OpenAIRE

    Góes, Dhiandra Amabille Simões

    2014-01-01

    Artigo – Trabalho de Conclusão de Curso apresentado à Fundação Universidade Federal de Rondônia – UNIR – Câmpus Prof. Francisco Gonçalves Quiles como requisito parcial para a obtenção do grau em Bacharel em Ciências Contábeis. Orientadora Profa. Me. Liliane Maria Nery Andrade o presente artigo apresenta os resultados de uma pesquisa de campo, exploratória e aplicada realizada em uma academia de ginástica localizada no município de Cacoal - RO. O objetivo da pesquisa foi identificar a deman...

  20. Standing Concertation Committee

    CERN Multimedia

    2007-01-01

    Ordinary meeting on 30 January 2007 The main items discussed at the meeting of the Standing Concertation Committee on 30 January 2007 included: Administrative Circular No. 26: with the introduction of the merit recognition system in the framework of the 5-yearly review of CERN employment conditions, Administrative Circular No. 26 has been revised. The committee took note of the revised document which is being finalized for submission to the Director-General for approval in the near future. Technical analysis of CERN Health Insurance Scheme: the Committee was informed that a group has been set up by the Director-General to analyse the financial situation of the CERN Health Insurance Scheme in the short and long term, and to propose measures to ensure that the Scheme remains in financial balance, with adequate cover, over the medium term. The group's terms of reference and membership were communicated. Voluntary programmes It was announced that the programmes: 'part-time work as a pre-retirement measure...

  1. Standing Concertation Committee

    CERN Multimedia

    2007-01-01

    ORDINARY MEETING ON 30 JANUARY 2007 The main items discussed at the meeting of the Standing Concertation Committee on 30 January 2007 included: Administrative Circular No. 26: with the introduction of the merit recognition system in the framework of the 5-yearly review of CERN employment conditions, Administrative Circular No. 26 has been revised. The Committee took note of the revised document which is being finalized for submission to the Director-General for approval in the near future. Technical analysis of CERN Health Insurance Scheme: the Committee was informed that a group has been set up by the Director-General to analyse the financial situation of the CERN Health Insurance Scheme in the short and long term, and to propose measures to ensure that the Scheme remains in financial balance, with adequate cover, over the medium term. The group's terms of reference and membership were communicated. Voluntary programmes It was announced that the programmes: 'part-time work as a pre-retirement mea...

  2. Standing Concertation Commmittee

    CERN Multimedia

    HR Department

    2007-01-01

    Ordinary meeting on 27 February 2007 The main items discussed at the meeting of the Standing Concertation Committee on 27 February 2007 included: Saved Leave Scheme (SLS): It was announced that a Management/Staff Association working group had been set up to discuss the Saved Leave Scheme (SLS): Members: M. Büttner, E. Chiaveri (chair), Ph. Defert, D. Klem, M. Vitasse, J.-M. Saint-Viteux. It was noted that the Staff Association was launching a questionnaire on SLS and distributed to all members of the personnel. Merit Recognition Guidelines : in the context of the new Merit Appraisal and Recognition Scheme (MARS), the committee took note of the CERN-wide 2007 Merit Recognition Guidelines, including the Frequently Asked Questions on HR Department's dedicated website. Information on CERN's medium and long-term plans (MTP-LTP)/Contract renewals/ External mobility The Committee took note of the information provided on CERN's MTP-LTP and of documentation distributed at the meeting by the Staff Associatio...

  3. Standing Concertation Committee

    CERN Document Server

    HR Department

    2007-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2007 The main items discussed at the meeting of the Standing Concertation Committee on 27 February 2007 included: Saved Leave Scheme (SLS): It was announced that a Management/Staff Association working group had been set up to discuss the Saved Leave Scheme (SLS): Members : M. Büttner, E. Chiaveri (chair), Ph. Defert, D. Klem, M. Vitasse, J.-M. Saint-Viteux. It was noted that the Staff Association was launching a questionnaire on SLS and distributed to all members of the personnel. Merit Recognition Guidelines: In the context of the new Merit Appraisal and Recognition Scheme (MARS), the committee took note of the CERN-wide 2007 Merit Recognition Guidelines, including the Frequently Asked Questions on HR Department's dedicated website. Information on CERN's medium and long-term plans (MTP-LTP)/Contract renewals/ External mobility The Committee took note of the information provided on CERN's MTP-LTP and of documentation distributed at the meeting by the Staff ...

  4. Stand-up physics

    CERN Multimedia

    2009-01-01

    A CMS physicist and amateur stand up comic was named the winner of NESTA FameLab 2009. Tom Whyntie battled it out with nine others young scientists from across the UK to win the contest to find the country’s next top science communicator. Tom Whyntie with his prize money after the NESTA Famelab final.Tom Whyntie, who is currently doing his PhD on the CMS experiment, managed to persuade his supervisor to give him a few days off on 5 June so he could fly back to the UK for the final of NESTA FameLab 2009. In the competition, which has been dubbed ‘the X Factor for scientists’, he had just three minutes to explain a complex scientific idea to a panel of judges made up of high-profile science professionals. During the final, he captivated the audience with his talk about how finding nothing at the LHC, far from being a waste of £5 billion, would actually catalyse the next scientific revolution. It Whyntie’s own words: "If the L...

  5. Standing concertation commmittee

    CERN Multimedia

    HR Department

    2009-01-01

    MEETINGS ON 2 AND 9 DECEMBER 2008 The main items discussed at the meetings of the Standing Concertation Committee on 2 and 9 December 2008 included: Medical Service Report 2007 The Committee took note of the report by Dr. E. Reymond (see http://sc-me.web.cern.ch/sc-me/fr/indexFR.htm) and of a number of points raised during the discussion. It was noted that the number of professional accidents declined in 2007 (361 accidents) in comparison with 2006 (483), as well as their gravity and frequency. The CERN Medical Service carried out a study on cancer prevalence (number of cases) and incidence (new cases per year per 100000 people), between 1993 and 2007, which identified some prostate, breast and colorectal cancers, though less than in the two Host States. Specific preventive actions will be promoted by the CERN CHISboard and the Medical Service in this context as well as in other areas. The committee expressed its thanks to all members of the Medical Service for their work i...

  6. Economic considerations of managing stands

    Science.gov (United States)

    Gary W. Miller

    1989-01-01

    Managing central hardwood stands involves making choices. Each year landowners face at least three alternatives for managing a stand: (1) allow it to grow undisturbed, (2) undertake a partial or complete commercial harvest, or (3) culture the timber crop through a precommercial investment. Each activity affects long-term monetary returns. The "best" choice in...

  7. Dynamics of Connecticut hemlock stands

    Science.gov (United States)

    Jeffrey S. Ward; David M. Smith

    2000-01-01

    The stand dynamics and production of two one-acre plots of eastern hemlock (Tsuga canadensis L) in Connecticut have been followed for more than six decades. Data were recorded for all individual trees. One plot (Saltonstall) was established in 1924 after the removal of a hardwood overstory. This stand had a nearly pure, almost fully closed understory...

  8. Solar Charged Stand Alone Inverter

    OpenAIRE

    M.Vasugi; Prof R.Jayaraman

    2014-01-01

    This paper deals with solar powered stand alone inverter which converts the variable dc output of a photovoltaic solar panel into ac that can be fed to loads. Stand alone inverters are used in systems where the inverter get its energy from batteries charged by photo voltaic arrays. A charge controller limits the rate at which electric current is added to or drawn from electric batteries. This charge discharge controller is needed to prevent the battery from being overcharged o...

  9. Teste GIN: detecção de gap em crianças com desvio fonológico Noise test: gap detection in children with phonological deviation

    Directory of Open Access Journals (Sweden)

    Elaine Feltre Assis

    2012-01-01

    Full Text Available OBJETIVO: investigar a resolução temporal: detecção de gaps em crianças com desvios fonológicos por meio do teste GIN e relacionar o grau do desvio fonológico com desempenho no teste GIN. MÉTODO: 6 indivíduos, de ambos os gêneros, 5 meninos e 1 menina, com idade entre 10 e 11 anos, com diagnóstico de desvio fonológico, em atendimento na clínica-escola do curso de Fonoaudiologia da FEAD de Belo Horizonte/MG, todos com ausência de perda auditiva e problemas neurológicos e/ou cognitivos. Os participantes foram submetidos ao Teste GIN, em intensidade de 50dB acima do limiar. RESULTADOS: das 06 crianças avaliadas, 5 (83,33% encontram-se alteradas e apenas 1 (16,67% obteve valores dentro do padrão de normalidade. Apesar da pequena amostra, viu-se que 83,33% das crianças com desvio fonológico tiveram limiares do GIN aquém do esperado para faixa etária. Porém não foi possível estabelecer uma relação direta entre grau de classificação do desvio fonológico e o baixo desempenho obtido no teste GIN, no qual apenas 1 criança com desvio médio moderado apresentou pior desempenho no teste GIN. CONCLUSÃO: crianças com desvio fonológico podem apresentar alteração no processamento temporal.PURPOSE: to investigate the temporal resolution, as for: gaps detection in children with phonological deviation through noise test and related with the degree of phonological performance in noise test. METHOD: 6 patients of both genders, five boys and one girl, aged between 10 and 11 year-old with phonological disorder' diagnosis in attendance at the school clinic of the Speech Therapy course (FEAD Belo Horizonte / MG, all with no hearing loss and no neurological and / or cognitive problems. The subjects underwent the GIN test at intensity of 50dB above the threshold. RESULTS: from the 6 evaluated children, 5 (83.33% had abnormal responses at gin test and only one (16.67% had values within the normal range. Despite the small sample, it was

  10. Teste GIN: detecção de gap em crianças com desvio fonológico Noise test: gap detection in children with phonological deviation

    Directory of Open Access Journals (Sweden)

    Elaine Feltre Assis

    2013-02-01

    Full Text Available OBJETIVO: investigar a resolução temporal: detecção de gaps em crianças com desvios fonológicos por meio do teste GIN e relacionar o grau do desvio fonológico com desempenho no teste GIN. MÉTODO: 6 indivíduos, de ambos os gêneros, 5 meninos e 1 menina, com idade entre 10 e 11 anos, com diagnóstico de desvio fonológico, em atendimento na clínica-escola do curso de Fonoaudiologia da FEAD de Belo Horizonte/MG, todos com ausência de perda auditiva e problemas neurológicos e/ou cognitivos. Os participantes foram submetidos ao Teste GIN, em intensidade de 50dB acima do limiar. RESULTADOS: das 06 crianças avaliadas, 5 (83,33% encontram-se alteradas e apenas 1 (16,67% obteve valores dentro do padrão de normalidade. Apesar da pequena amostra, viu-se que 83,33% das crianças com desvio fonológico tiveram limiares do GIN aquém do esperado para faixa etária. Porém não foi possível estabelecer uma relação direta entre grau de classificação do desvio fonológico e o baixo desempenho obtido no teste GIN, no qual apenas 1 criança com desvio médio moderado apresentou pior desempenho no teste GIN. CONCLUSÃO: crianças com desvio fonológico podem apresentar alteração no processamento temporal.PURPOSE: to investigate the temporal resolution, as for: gaps detection in children with phonological deviation through noise test and related with the degree of phonological performance in noise test. METHOD: 6 patients of both genders, five boys and one girl, aged between 10 and 11 year-old with phonological disorder' diagnosis in attendance at the school clinic of the Speech Therapy course (FEAD Belo Horizonte / MG, all with no hearing loss and no neurological and / or cognitive problems. The subjects underwent the GIN test at intensity of 50dB above the threshold. RESULTS: from the 6 evaluated children, 5 (83.33% had abnormal responses at gin test and only one (16.67% had values within the normal range. Despite the small sample, it was

  11. Avaliação da qualidade de vida em funcionários praticantes de ginástica holística em empresa

    OpenAIRE

    Fernanda Fonseca dos Santos Lopes; Zelia Zilda Lourenço de Camargo Bittencourt

    2012-01-01

    Introdução: A qualidade de vida na empresa é um importante recurso de promoção de saúde, e pode ser desenvolvida a partir da pratica de atividades físicas. O exercício físico é uma forma de lazer e de restaurar a saúde dos efeitos da rotina estressante do trabalho, proporcionando condições de melhor desempenho e produtividade. A Ginástica Holística atua através da sensibilização e da tomada de consciência, de modo a levar o sujeito a uma melhor utilização do seu potencial perceptivo, sensoria...

  12. Avaliação dos benefícios da ginástica localizada sobre a postura e a flexibilidade de mulheres na terceira idade

    OpenAIRE

    Lima,Hélia Cristina Oliveira; Aguiar,Jaina Bezerra de; Paredes,Paulo Fernando Machado; Gurgel,Luilma Albuquerque

    2010-01-01

    Desvios posturais e redução na flexibilidade são alterações observadas com o avançar da idade, podendo desencadear dor e dificuldades de movimentação. Este estudo buscou avaliar a influência de um programa de ginástica, de dois meses de duração, sobre a postura e flexibilidade de idosas institucionalizadas (n = 10, 60-75 anos). A postura foi avaliada através do uso de simetrógrafo, fotografias e do teste de equilíbrio sagital pélvico, e a flexibilidade através do teste de sentar e alcançar. C...

  13. Extensionando “saúdes”, produzindo sociabilidades: o projeto "ginástica para comunidade" da Universidade Federal do Rio Grande

    OpenAIRE

    Freitas, Gustavo da Silva; Nunes, Giovana Valente; Teixeira, Juliana Cotting

    2014-01-01

    Trabalho apresentado no 31º SEURS - Seminário de Extensão Universitária da Região Sul, realizado em Florianópolis, SC, no período de 04 a 07 de agosto de 2013 - Universidade Federal de Santa Catarina. O Projeto “Ginástica para a Comunidade” está em ação há mais de dezesseis anos tendo sido criado por iniciativa de professores de Educação Física da Universidade Federal do Rio Grande (FURG), motivados em se integrar à comunidade numa ação de extensão. Com diferentes propósitos e formatos ao ...

  14. Isotope separation by standing waves

    International Nuclear Information System (INIS)

    Altshuler, S.

    1984-01-01

    The separation of isotopes is accomplished by scattering a beam of particles from a standing electromagnetic wave. The particles may consist of either atoms or molecules, the beam having in either case a desired isotope and at least one other. The particle beam is directed so as to impinge on the standing electromagnetic wave, which may be a light wave. The particles, that is, the atomic or molecular quantum-mechanical waves, see basically a diffraction grating corresponding to the troughs and peaks of the electromagnetic wave. The frequency of the standing electromagnetic wave substantially corresponds to an internal energy level-transition of the desired isotope. Accordingly, the desired isotope is spatially separated by being scattered or diffracted. (author)

  15. Residual Liquefaction under Standing Waves

    DEFF Research Database (Denmark)

    Kirca, V.S. Ozgur; Sumer, B. Mutlu; Fredsøe, Jørgen

    2012-01-01

    This paper summarizes the results of an experimental study which deals with the residual liquefaction of seabed under standing waves. It is shown that the seabed liquefaction under standing waves, although qualitatively similar, exhibits features different from that caused by progressive waves....... The experimental results show that the buildup of pore-water pressure and the resulting liquefaction first starts at the nodal section and spreads towards the antinodal section. The number of waves to cause liquefaction at the nodal section appears to be equal to that experienced in progressive waves for the same...

  16. Burnout : de stand van zaken

    NARCIS (Netherlands)

    Taris, T.; Houtman, I.L.D.; Schaufeli, W.

    2013-01-01

    Dit artikel geeft een overzicht van de stand van zaken in het onderzoek naar burnout. Burnout is een syndroom van extreme vermoeidheid (uitputting), afstand nemen van het werk (distantie) en weinig vertrouwen in het eigen kunnen (verminderde competentie), waarbij de oorzaken voor deze aspecten

  17. Características sócio-culturais de práticas ginásticas e futebolísticas no sul do brasil ao final do século XX

    OpenAIRE

    BRUNO, Giancarlo Bazarele Machado; Universidade Federal de Pelotas

    2013-01-01

    Com entrevistas, observações, quantificações e metragens, estudou-se as academias de Ginástica e os locais de Futsal e de Soccer em Pelotas/RS. Um total de 1.570 praticantes, 44,8 alunos/academia, 97 % mulheres, praticavam principalmente Ginástica Localizada, Aeróbica e Step, em 35 locais, área média de 205,4 m2. Pertenciam à iniciativa privada 91,4%, e as restantes a clubes sociais. A maior freqüência era no período antes do verão e entrel7:00 e 22:00 horas. O custo médio, para exercitação d...

  18. Ninguém é de ferro: a construção da corporeidade em uma academia de ginástica feminina de um bairro popular em João Pessoa

    OpenAIRE

    Lira, Manuella Ribeiro Barbosa

    2014-01-01

    A pesquisa que se segue tem como eixo central a construção do corpo feminino na atual sociedade, a partir do desenvolvimento de uma experiência etnográfica em uma academia de ginástica só para mulheres, localizada em um bairro popular da cidade de João Pessoa, no período entre os meses de dezembro de 2012 a dezembro de 2013. Os objetivos do estudo são investigar de que maneira o corpo é construído nas práticas e nos discursos da academia de ginástica só para mulheres, quais os ...

  19. Avaliação do equilíbrio estático e dinâmico de idosas praticantes de hidroginástica e ginástica

    OpenAIRE

    Almeida, Ana Paula Pessoa Veloso de; Veras, Renato Peixoto; Doimo, Leonice Aparecida

    2010-01-01

    Este estudo avaliou o equilíbrio estático e dinâmico e valências motoras relacionadas em idosas praticantes de ginástica e hidroginástica. Participaram 31 mulheres na modalidade hidroginástica (GH, 69,32 ± 6,57 anos) e 28 na ginástica (GG; 65,57 ± 7,67 anos), com no mínimo seis meses de prática e frequência mínina de três vezes na semana. Foram realizadas medidas de estatura (cm), peso (kg) e circunferências de cintura, quadril e abdome (cm) e cálculos do índice de massa corporal (IMC) e rela...

  20. Stand up and move forward

    OpenAIRE

    de Jong, Johan; Shokoohi, Roya

    2017-01-01

    Insufficient physical activity or being inactive is one of the leading risk factors for non-communicable diseases worldwide. Globally between 6-10% of premature mortality, caused by non-communicable diseases, could be avoided if people adhered to general physical activity guidelines. Besides that, studies link sitting for prolonged periods of time with many serious health concerns. The solution seems simple: Stand up and move forward. However, human behavior is difficult to change – due to th...

  1. Ginástica geral na escola: uma proposta metodológica General gymnastics at school: A methodological propositon Gimnasia general en la escuela: Una propuesta metodológica

    Directory of Open Access Journals (Sweden)

    2006-11-01

    Full Text Available Este trabalho tem por objetivo discutir a Ginástica como conteúdo da Educação Física escolar, por meio da Ginástica geral como proposta metodológica. Tal proposta tem como perspectiva a integração das diversas manifestações gímnicas e os outros componentes da cultura corporal, sendo sua principal característica a ausência da competição. PALAVRAS-CHAVE: ginástica – ginástica geral – educação física escolar. This study aims at discussing gym classes as a part of school physical education, using General Gymnastics as a methodological approach. Such an approach has the perspective of integrating the several gymnastic manifestations to the other components of body culture, with the lack of competition as its main feature. KEY WORDS: gym – general gymnastics – physical education in schools. Este trabajo tiene por objetivo discutir la Gimnasia como contenido de la Educación Física escolar, por medio de la Gimnasia general como propuesta metodológica. Tal propuesta tiene como perspectiva la integración de diversas manifestaciones gímnicas y los otros componentes de la cultura corporal, siendo su principal característica la ausencia de la competencia. PALABRAS-CLAVE: gimnasia – gimnasia general – educación física escolar.

  2. Transpalpebral eye enucleation in the standing horse

    DEFF Research Database (Denmark)

    Christophersen, Mogens Teken

    Transpalpebral eye enucleation in the standing horse. The Nordic Equine Veterinary Conference, Proceedings, Copenhagen. Denmark. Nov. 2011.......Transpalpebral eye enucleation in the standing horse. The Nordic Equine Veterinary Conference, Proceedings, Copenhagen. Denmark. Nov. 2011....

  3. Compatible growth models and stand density diagrams

    International Nuclear Information System (INIS)

    Smith, N.J.; Brand, D.G.

    1988-01-01

    This paper discusses a stand average growth model based on the self-thinning rule developed and used to generate stand density diagrams. Procedures involved in testing are described and results are included

  4. A recepção da ginástica sueca em Portugal nas primeiras décadas do século XX: conformidades e dissensões culturais e políticas

    Directory of Open Access Journals (Sweden)

    Luís Miguel Carvalho

    2015-06-01

    Full Text Available O artigo aborda a presença persistente da "ginástica sueca" como referente principal da educação física em contexto escolar em Portugal, nas primeiras décadas do século XX, e as recepções distintas de que foi alvo. Numa primeira parte, o texto centra-se na compreensão da centralidade adquirida pela "ginástica sueca", em múltiplos contextos geopolíticos, no contexto da consolidação do projeto da escola de massas. Numa segunda parte, o texto documenta e analisa algumas deslocações interpretativas ocorridas na recepção da "ginástica sueca" em Portugal, entre 1920 e 1940, bem como os realinhamentos educativos, sociais e políticos que acompanharam esses conflitos sobre a sua "correta" mobilização para o contexto escolar português.

  5. El Manuscrito Cerramientos y trazas de montea de Ginés Martínez de Aranda

    Directory of Open Access Journals (Sweden)

    Calvo López, José

    2009-03-01

    Full Text Available Ginés Martínez de Aranda, master mason in the cathedrals of Cádiz and Santiago de Compostela during the late 16th century, wrote a manuscript, Cerramientos y trazas de montea, concerning geometrical problems in stone construction. This article deals with the copy of Cerramientos in the Servicio Histórico Militar (Madrid, its copyist, dating, the existence of an earlier version and whether or not Aranda intended to publish it. Also examined are the connections between Cerramientos and other Spanish stonecutting texts of the period, such as those by Alonso de Vandelvira, Cristóbal de Rojas, Alonso de Guardia or Juan de Portor y Castro. Finally, an assessment is made of Martínez de Aranda’s original contributions to European stonecutting literatura.

    El arquitecto y cantero baezano Ginés Martínez de Aranda, que trabajó a finales del siglo XVI y ejerció la maestría de las catedrales de Cádiz y Santiago de Compostela, compuso un manuscrito llamado Cerramientos y trazas de montea, que trata de los problemas geométricos de la construcción pétrea. El artículo analiza la copia del manuscrito conservada en el Servicio Histórico Militar de Madrid, la identidad del copista, la fecha de la primera redacción de la obra y la de la copia conservada, y el destino de la obra; a continuación, se estudia la relación del manuscrito con otras obras españolas de cantería, en especial las de Alonso de Vandelvira, Cristóbal de Rojas, Alonso de Guardia y Juan de Portor y Castro, para finalizar tratando diversas aportaciones originales de Aranda a la literatura europea de la cantería.

  6. Mägede vaikuses ja lumeväljade lummuses / Kristjan Erik Suurväli

    Index Scriptorium Estoniae

    Suurväli, Kristjan Erik

    2003-01-01

    MTÜ Freerider esindajatel Peeter Luigel ja Kristjan Erik Suurväljal avanes võimalus Russian Heliboarding Club kutsel käia tutvumas heliski võimalustega Kaukaasia, Usbekistani ja Kõrgõstani mägedes

  7. 24 CFR 206.37 - Credit standing.

    Science.gov (United States)

    2010-04-01

    ... CONVERSION MORTGAGE INSURANCE Eligibility; Endorsement Eligible Mortgagors § 206.37 Credit standing. Each mortgagor must have a general credit standing satisfactory to the Secretary. ... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Credit standing. 206.37 Section 206...

  8. The one-leg standing radiograph

    OpenAIRE

    Pinsornsak, P.; Naratrikun, K.; Kanitnate, S.; Sangkomkamhang, T.

    2016-01-01

    Objectives The purpose of this study was to compare the joint space width between one-leg and both-legs standing radiographs in order to diagnose a primary osteoarthritis of the knee. Methods Digital radiographs of 100 medial osteoarthritic knees in 50 patients were performed. The patients had undergone one-leg standing anteroposterior (AP) views by standing on the affected leg while a both-legs standing AP view was undertaken while standing on both legs. The severity of the osteoarthritis wa...

  9. Effects of Pyrolysis Temperature on Product Yields and Energy Recovery from Co-Feeding of Cotton Gin Trash, Cow Manure, and Microalgae: A Simulation Study

    Science.gov (United States)

    Hanif, Muhammad Usman; Capareda, Sergio C.; Iqbal, Hamid; Arazo, Renato Ortiz; Baig, Muhammad Anwar

    2016-01-01

    The intensive search of new and cleaner energy catches interest in recent years due to huge consumption of fossil fuels coupled with the challenge of energy and environmental sustainability. Production of renewable and environmentally benign energy from locally available raw materials is coming in the frontline. In this work, conversion of the combined biomass (cotton gin trash, cow manure, and Microalgae [Nannochloropsis oculata]) through batch pyrolysis has been investigated. The effect of temperature to the production of energy fuels such as bio-oil, char, and biogas have been simulated considering the yield and energy content as responses. Result of the investigation generally revealed that the proportions of the different biomass did not significantly affect the product yield and energy recovery. Significant effect of temperature is evident in the simulation result of energy recovery whereby maximum conversion was achieved at 400°C for char (91 wt%), 600°C for syngas (22 wt%), and 551°C for bio-oil (48 wt%). Overall energy conversion efficiency of 75.5% was obtained at 589°C in which 15.6 MJ/kg of mixed biomass will be elevated to pyrolysis products. PMID:27043929

  10. Efeitos do "feedback" autocontrolado na aprendizagem do lançamento da bola da ginástica rítmica

    Directory of Open Access Journals (Sweden)

    Anielle Lemos

    2013-09-01

    Full Text Available O objetivo do presente estudo foi investigar os efeitos da frequência autocontrolada de "feedback" na aprendizagem do lançamento da bola da ginástica rítmica. A amostra foi constituída de 24 crianças, de sete a 10 anos de idade, distribuídas em dois grupos em relação aos diferentes tipos de condições de "feedback": autocontrolado e externamente controlado. O estudo foi composto de uma fase de prática e um teste de retenção. Os resultados de um questionário revelaram que a maioria dos participantes do grupo autocontrolado solicitou "feedback" principalmente após as boas tentativas de prática, enquanto os participantes do grupo "yoked" indicaram ter recebido "feedback" nas tentativas em que o desejavam. Nenhuma diferença foi encontrada em relação ao desempenho ou aprendizagem. Conclui-se que a frequência autocontrolada de "feedback" é tão eficiente quanto a frequência externamente controlada na aprendizagem da habilidade motora específica lançamento do aparelho bola em crianças desta faixa etária.

  11. Desequilíbrio hormonal e disfunção menstrual em atletas de ginástica rítmica

    Directory of Open Access Journals (Sweden)

    Sabrina Macedo Hott Coelho

    2015-09-01

    Full Text Available ResumoObjetivou-se avaliar a magnitude das alterações de hormônios reguladores do ciclo menstrual (CM e testosterona de atletas de ginástica rítmica (GR de alto rendimento, em período pré-competitivo para a Olimpíada de Beijing. Foram realizadas coletas de sangue em 4 momentos, com intervalos de 7 dias. Os hormônios estrogênio, progesterona, luteinizante (LH, folículo estimulante (FSH e testosterona foram mensurados por quimioluminescência. As atletas (n = 7 relataram disfunção menstrual e houve expressiva variação hormonal intra e entre indivíduos. Das amostras de estrogênio, 65% ficaram abaixo do valor referencial clínico, enquanto que as concentrações de progesterona e LH ficaram próximas ao limite inferior. Para FSH e testosterona, 10% e 30% das amostras, respectivamente, ficaram abaixo do referencial. Conclui-se que atletas de alto rendimento em GR apresentam maior risco de desequilíbrio hormonal e disfunção menstrual, o que inspira necessidade de atenção clínica.

  12. Interação entre leptina, ginástica artística, puberdade e exercício em atletas do sexo feminino

    Directory of Open Access Journals (Sweden)

    Tatiana de Barros Meira

    2010-09-01

    Full Text Available Há evidências de que as atletas de ginástica artística (GA apresentam desregulações no sistema reprodutório em relação à média populacional. A interação entre alguns fatores pode explicar esse fato: genética, estresse do exercício, baixa porcentagem de gordura corporal, má nutrição e ação da leptina. Por meio de uma revisão de literatura, discutimos resultados de pesquisas que relacionam a ação do hormônio leptina e desregulações no sistema reprodutório durante a puberdade em atletas de GA do sexo feminino. Podemos afirmar que existe uma interação entre a seleção natural na modalidade, a baixa ingestão calórica e o estresse do treinamento, que ocasionaria a diminuição de leptina plasmática e causaria desregulações no sistema reprodutório durante a puberdade.

  13. Thinning in artificially regenerated young beech stands

    Directory of Open Access Journals (Sweden)

    Novák Jiří

    2015-12-01

    Full Text Available Although beech stands are usually regenerated naturally, an area of up to 5,000 ha year−1 is artificially regenerated by beech in the Czech Republic annually. Unfortunately, these stands often showed insufficient stand density and, consequently, lower quality of stems. Therefore, thinning methods developed for naturally regenerated beech stands are applicable with difficulties. The paper evaluates the data from two thinning experiments established in young artificially regenerated beech stands located in different growing conditions. In both experiments, thinning resulted in the lower amount of salvage cut in following years. Positive effect of thinning on periodic stand basal area increment and on periodic diameter increment of dominant trees was found in the beech stand located at middle elevations. On the other hand, thinning effects in mountain conditions were negligible. Thinning focusing on future stand quality cannot be commonly applied in artificially regenerated beech stands because of their worse initial quality and lower density. However, these stands show good growth and response to thinning, hence their management can be focused on maximising beech wood production.

  14. Refrigeration system having standing wave compressor

    Science.gov (United States)

    Lucas, Timothy S.

    1992-01-01

    A compression-evaporation refrigeration system, wherein gaseous compression of the refrigerant is provided by a standing wave compressor. The standing wave compressor is modified so as to provide a separate subcooling system for the refrigerant, so that efficiency losses due to flashing are reduced. Subcooling occurs when heat exchange is provided between the refrigerant and a heat pumping surface, which is exposed to the standing acoustic wave within the standing wave compressor. A variable capacity and variable discharge pressure for the standing wave compressor is provided. A control circuit simultaneously varies the capacity and discharge pressure in response to changing operating conditions, thereby maintaining the minimum discharge pressure needed for condensation to occur at any time. Thus, the power consumption of the standing wave compressor is reduced and system efficiency is improved.

  15. Reineke’s stand density index: a quantitative and non-unitless measure of stand density

    Science.gov (United States)

    Curtis L. VanderSchaaf

    2013-01-01

    When used as a measure of relative density, Reineke’s stand density index (SDI) can be made unitless by relating the current SDI to a standard density but when used as a quantitative measure of stand density SDI is not unitless. Reineke’s SDI relates the current stand density to an equivalent number of trees per unit area in a stand with a quadratic mean diameter (Dq)...

  16. The Stand-alone Heliostat

    International Nuclear Information System (INIS)

    Garcia Navajas, G. I.; Egea Gea, A.

    2000-01-01

    The first Autonomous Heliostat has been developed by CIEMAT at PSA facilities in Almeria. This heliostat is an innovative approach to reducing the civil engineering work costs in heliostat fields of central tower plants. Channels, cables and other electric elements have been eliminated in the new heliostat. Thus, one 70-nr, classical T glass/metal heliostat has been adapted to include all the new stand-alone concept components. A PV system is able to drive two sun-tracking DC motors between 5 and 24Vdc, 0 and 15A. The heliostat communicates with the control room 400-m away by using a radio-modem working at 9600 baud. An anemometer, a wind switcher, light and ambient temperature sensors have been installed on the heliostat for self-protection decision-making. A PV panel integrated into the heliostat reflecting surface, eliminates cabling and other elements required for a conventional power supply. Communication lines between master control and local control have been replaced by radio-modem. Testing has validated the technical feasibility of the prototype and quantified the real consumption and efficiencies of new elements. The extra costs produced.by the autonomous concepts are compared with the cost of civil work in conventional heliostat field. (Author) 8 refs

  17. Recensão crítica do livro 'Exposição a fungos dos trabalhadores dos ginásios com piscina', de Carla S. C. Viegas

    OpenAIRE

    Santos, Carlos Silva

    2012-01-01

    A amplitude e diversidade dos agentes micóticos, fatores de risco profissional de um grupo particular de trabalhadores, é claramente esplanada na revisão bibliográfica que, de uma forma pedagógica e descritiva, refere as características essenciais das espécies fúngicas patogénicas para o Homem, nomeadamente fungos dermatófilos, leveduras e fungos filamentosos não dermatófilos. A prevalência de Tínea pedis e onicomicose, os fatores predisponentes e o contexto profissional dos ginásios co...

  18. Desenvolvimento e avaliação da estabilidade de emulsões O/A com cristais líquidos acrescidas de xantina para tratamento da hidrolipodistrofia ginóide (celulite)

    OpenAIRE

    Gilsane Garcia Morais

    2006-01-01

    Atualmente, decorrente da cultura estética onde há o culto aos corpos esbeltos com aparência saudável e pele lisa, macia e viçosa, a hidrolipodistrofia ginóide, conhecida como celulite, tem sido um dos desafios para os dermatologistas e cirurgiões plásticos. Assim, temse testado diferentes formas de tratamentos entre as quais estão aplicações de cremes à base de xantinas visando a atenuação dos sintomas. O conhecimento das propriedades físicoquímicas de tais formulações é essencial para otimi...

  19. Metodologia do ensino de ginástica: novos olhares, novas perspectivas Gym teaching methodology: new approaches, new perspectives Metodología de enseñanza de la gimnasia: Nuevos horizontes, nuevas perspectivas

    Directory of Open Access Journals (Sweden)

    2006-11-01

    Full Text Available Este artigo busca sistematizar uma proposta metodológica para o ensino da Ginástica escolar e comunitária, que vem sendo construída a partir de experiências realizadas junto aos projetos de ensino, pesquisa e extensão vinculados ao Grupo de Estudo, Pesquisa e Experimentação em Ginástica(GEPEGIN, da Faculdade de Educação Física da UFG. A proposta indica alguns princípios, conteúdos e estratégias de ação que possam contribuir para o processo de formação humana crítica, na tentativa de apontar uma nova perspectiva para o ensino, a prática e o conhecimento da Ginástica. PALAVRAS-CHAVE: metodologia da ginástica – formação humana – linguagem corporal. This article aims at systematizing a methodological approach for the teaching of gym in schools and communities, which is being built from the experiences held with teaching, research, and extension (community-bound projects linked to GEPEGIN - the Study, Research, and Gym Experimentation Group, from the Physical Education Department at UFG - the Federal University of Goias. This approach indicates some principles, contents, and strategies for action that might contribute to the process of human education in a critical way, in an attempt to point towards a new perspective for the teaching, the practice, and the knowledge of Gymnastics. KEY-WORDS: gymnastics methodology – human education – body language. Este artículo busca sistematizar una propuesta metodológica para la enseñanza de la Gimnasia escolar y comunitaria, que viene siendo construida a partir de experiencias realizadas junto a los proyectos de enseñanza, pesquisa y extensión vinculados al Grupo de Estudio, Pesquisa y Experimentación en Gimnasia (GEPEGIN, de la Facultad de Educación Física de la UFG. La propuesta indica algunos principios, contenidos y estrategias de acción que puedan contribuir para el proceso de formación humana crítica, intenta señalar una nueva perspectiva para la ense

  20. SPEED ROLLER STAND MEASUREMENT SYSTEM CHECKING TECHNIQUE

    Directory of Open Access Journals (Sweden)

    Y. Zybtsev

    2011-01-01

    Full Text Available The study has shown that the accuracy of brakes checking by inertial stands depends upon the applied methods of measurement of braking parameters (stand slowing down, braking distance, brakes triggering time, current speed as well as the methods of metrological checking of measuring system canals.

  1. Evaluating growth performance of young stands

    Science.gov (United States)

    A. L. Roe; R. E. Benson

    1966-01-01

    A simple procedure for evaluating the diameter growth of young stands in relation to potential growth is described. A comparison technique is developed which contrasts relative diameter of crop trees to the relative diameter growth of the last decade to show the condition and trend of growth in the stand. The method is objective, easy to use, and has several...

  2. Introducing sit-stand desks increases classroom standing time among university students

    Directory of Open Access Journals (Sweden)

    Matthew Jerome

    2017-12-01

    Full Text Available Excessive sedentary behavior has been associated with many negative health outcomes. While an understudied health topic, there is evidence that university students are excessively sedentary. Sit-stand desks have been shown to reduce sedentary time among pre-university students (ages 5–18years and sedentary workers but have not been tested in university classrooms. This study tested the effects of introducing sit-stand desks into a university classroom on student's classroom sitting and standing behaviors. Using a cross-over design, students received access to both traditional seated desks and sit-stand desks for six weeks. Data were collected between September and December, 2016. We recruited 304 healthy undergraduate university students enrolled in one of two small (25 seats classrooms at a large Midwestern university during the fall of 2016. Average minutes of standing/hour/student, average percent class time spent standing, and the number of sit-stand transitions/student/hour were directly observed with video camera surveillance. Participants stood significantly more (p<0.001 when provided access to sit-stand desks (7.2min/h/student; 9.3% of class time spent standing compared to when they had access to seated desks (0.7min/h/student; 1.6% of class time spent standing but no differences were observed for the number of sit-stand transitions (p=0.47. Students reported high favorability for the sit-stand desks and improvements in several student engagement and affective outcomes while using the sit-stand desks. These findings support introducing sit-stand desks in university classrooms as an approach to reduce sedentary behaviors of university students. Keywords: Sedentary, University students, Sit-stand desk

  3. Juvenile offenders: competence to stand trial.

    Science.gov (United States)

    Soulier, Matthew

    2012-12-01

    This article details the legal background and assists the reader in the preparation and practical conduct of evaluations regarding juvenile adjudicative competency. The material is presented to be useful as a guide to direct questions of competency and covers aspects of evaluation that include: legal standard for competency to stand trial, developmental immaturity, current practice in juvenile competency to stand trial, forensic evaluation of juvenile competency to stand trial, organizing the evaluation, collateral sources of information, psychiatric evaluation of juvenile adjudicative competency, assessment of mental disorder and intellectual disability, assessment of developmental status, assessment of functional abilities for adjudicative competence, and reaching the forensic opinion. Copyright © 2012 Elsevier Inc. All rights reserved.

  4. Recent advances in standing equine orthopedic surgery.

    Science.gov (United States)

    O'Brien, Thomas; Hunt, Robert J

    2014-04-01

    In all surgeries with the patient standing under chemical and physical restraint, patient compliance is of the utmost importance. All fractures of the third metacarpal or metatarsal condyles and sagittal fracture of the first phalanx are not amenable to internal fixation with the horse standing, and young unhandled horses may not have a suitable disposition for standing surgical treatment of septic pedal osteitis, or implantation and removal of transphyseal screws. Previous operator experience in performing the procedure or technique under general anesthesia is beneficial. Appreciation of appropriate topographic anatomic landmarks is important, and intraoperative radiographic control is useful. Copyright © 2014 Elsevier Inc. All rights reserved.

  5. Insatisfação corporal de adolescentes atletas e não atletas de ginástica artística

    Directory of Open Access Journals (Sweden)

    Clara Mockdece Neves

    2016-03-01

    Full Text Available DOI: http://dx.doi.org/10.5007/1980-0037.2016v18n1p82   A avaliação de fatores psicológicos pode auxiliar na prevenção de transtornos alimentares em atletas. Objetivou-se verificar possíveis relações entre a insatisfação corporal e influência da mídia, perfeccionismo, estado de humor e comportamento de risco para transtorno alimentar, bem como comparar as variáveis de estudo entre praticantes de ginástica artística de base e de alto rendimento e não atletas. Participaram da pesquisa 413 adolescentes de ambos os sexos (atletas de alto rendimento e de base e não atletas, com idade entre 10 e 18 (média de 12,86±1,80 anos. Foram aplicados: BSQ, EAT-26, SATAQ-3, MPS e BRUMS para avaliar insatisfação corporal, comportamento de risco para transtorno alimentar, influência midiática, perfeccionismo e estado de humor, respectivamente. Foram coletados dados antropométricos para estimar o Índice de Massa Corporal (IMC e o Percentual de Gordura (%G. Foram realizadas análises estatísticas descritivas, comparativas e correlacionais. Somente o EAT-26 influenciou o BSQ nos três grupos avaliados. Em não atletas, IMC, BRUMS e SATAQ-3 acrescentaram explicação ao modelo. Para os atletas de base, %G, influência da mídia e estado de humor também foram preditores para a insatisfação corporal. Os atletas de alto rendimento tiveram menores valores de IMC e %G do que os demais. Os não atletas apresentaram menores escores para o perfeccionismo, enquanto os atletas de base menores pontuações para o estado de humor. Conclui-se que o comportamento de risco para transtorno alimentar é o fator que se relaciona mais fortemente com a insatisfação corporal em atletas de base, de alto rendimento e em não atletas.

  6. Pasiones políticas e imperialismo : la polémica entre Ginés de Sepúlveda y Bartolomé de las Casas

    Directory of Open Access Journals (Sweden)

    Sandra Chaparro

    2001-01-01

    Full Text Available Durante siglos el «amor» se ha venido considerando una virtud política, sostenedora de la vida comunitaria y fuente de la solidaridad social. Como tal, se trata de una pasión que se encuentra en la base de los sistemas simbólicos del pensamiento político occidental, si bien hoy, pasiones y política parecen dos conceptos alejados entre sí No obstante, en un mundo en vías de globalización resurgen con fuerza términos como solidaridad o cooperación, conceptos que implican una buena dosis de «amor político». El objeto de este trabajo es recurrir al ejemplo histórico como una buena manera de señalar los riesgos y limitaciones de esta estrategia. Así, en él se analizan los debates suscitados en el siglo xvi en torno a la forma correcta de cristianizar a las sociedades indígenas americanas a través de la polémica entre el «universalismo benevolente» de Bartolomé de las Casas y la idea de «cruzada como acto de amor» de Ginés de Sepúlveda. Esta polémica histórica resulta ser un magnifico ejemplo de la disputa en torno a la correcta utilización de las «pasiones políticas».For centuries, «love» as been a political virtue enhancing communitarism and social solidarity. As such, it as been a passion we find in the basis of the symbolic systems of wesern political thought, though nowadays passions and politics seem to be different realities. Nevertheless, in a worid in which globalization process take place, concepts based on «political love» like solidarity or cooperation recover their original force. The aim of this study is to appeal to an historical example to show the risks and limits of certain kinds of globalization strategies. This article is about the debates that took place in the sixteenth century, when jurists and theologians had to decide which was the right way of christianizing american natives. The historical debate between Bartolomé dse las Casas and his concept of «benevolent universalism» and Gines

  7. Influência de informações de saúde no estilo de vida de participantes de ginástica laboral

    Directory of Open Access Journals (Sweden)

    Raquel Suelen Brito Silva

    2014-09-01

    Full Text Available Objetivo: Verificar a influência que informações repassadas durante avaliação antropométrica teriam nos hábitos relacionados a exercícios físicos (ExF e alimentação de 14 participantes (fem=11; 51,07  8,17 anos do Programa de Ginástica Laboral da Universidade Federal da Paraíba (PGL da UFPB. Métodos: A pesquisa foi descritivo transversal, com abordagem quanti-qualitativa Foram aplicadas, entre março e maio de 2010, avaliação antropométrica e entrevista semiestruturada. Durante a avaliação foram providas informações e orientações sobre saúde. Resultados: Verificou-se que: a amostra indicou média de pré-obesidade, risco aumentado de desenvolvimento de doenças crônicas não transmissíveis e pré-hipertensão. Os discursos sugeriram que cinco trabalhadores adotaram ou aumentaram a prática de ExF, cinco pretendiam passar a se exercitar, três mantiveram a prática de ExF, um inclusive passou a realizar ExF com seu cônjuge e dos dois que começaram a se alimentar melhor, um não pretendia se exercitar. A caminhada foi praticada por seis indivíduos e a informação repassada na avaliação antropométrica considerada mais importante foi sobre massa corporal (n=5. Conclusão: As informações repassadas na avaliação antropométrica do PGL da UFPB podem ter sido eficientes em provocar mudanças positivas no estilo de vida dos trabalhadores estudados, evidenciando que essa transmissão de informações tem a capacidade de fomentar um estilo de vida fisicamente ativo e saudável. NCT01943734

  8. Impacto do beneficiamento sobre o número de neps e quantidade de impurezas da fibra do algodão Ginning impact on the number of neps and amount of cotton fiber contaminants

    Directory of Open Access Journals (Sweden)

    Odilon R. R. F. da Silva

    2010-01-01

    Full Text Available Objetivou-se, neste trabalho, estudar o efeito do beneficiamento sobre o conteúdo de impurezas, pó e o número de neps na pluma, em 12 algodoeiras do Estado de Mato Grosso. O experimento consistiu de uma combinação fatorial de cinco etapas de beneficiamento do algodão em 12 algodoeiras em delineamento inteiramente casualizado com quatro repetições. Amostras de algodão foram coletadas nas seguintes etapas: a no desmanche do fardão; b antes do descaroçamento; c logo após o descaroçamento; d na bica, sem o uso do limpador tipo serrilha; e na bica, após a limpeza da pluma, utilizando-se o limpador tipo serrilha. Em todas as etapas se retiraram quatro amostras padrão de pluma com massa de 350 g a fim de serem analisadas mediante o instrumento AFIS (Advanced Fiber Information System para determinação do conteúdo de impurezas e poeira e o número de neps da fibra. Os resultados indicam que os processos de prelimpeza do algodão em caroço e limpeza da pluma reduzem o conteúdo de impurezas e da poeira do algodão enquanto, juntamente com o descaroçamento, esses processos aumentaram o número de neps da fibra do algodão. A utilização do limpador de pluma tipo serrilha com manta contínua aumenta a eficiência de limpeza da pluma, porém ocasiona incrementos significativos no número de neps.The purpose of this work was to study the ginning effect on the amount of cotton contaminants, dust and neps in cotton fiber, in 12 industries in the Mato Grosso State. The experiment consisted of a factorial combination over five stages of ginning and 12 cotton industries using a randomized design with four replications. Some samples of cotton were collected in the following phases: a in the bale dismantling; b before the ginning; c right after ginning; d into the covered lint slide not using the saw lint cleaner; and e into the covered lint slide, after cleaning process using the saw lint cleaner system. Over all stages four standard samples of

  9. Basic Stand Alone Medicare Inpatient Claims PUF

    Data.gov (United States)

    U.S. Department of Health & Human Services — This release contains the Basic Stand Alone (BSA) Inpatient Public Use Files (PUF) named CMS 2008 BSA Inpatient Claims PUF with information from 2008 Medicare...

  10. Compressor Load Stand: Commissioning and Control Strategies

    National Research Council Canada - National Science Library

    Causey, Andrew

    1998-01-01

    .... The purpose of this research project was to commission this load stand, which includes setting up the hardware, setting up a control system, a data acquisition system, and an automatic test sequence system...

  11. Minnesota DNR Forest Stand Inventory Version 2

    Data.gov (United States)

    Minnesota Department of Natural Resources — This layer is a digital inventory of individual forest stands. The data is collected by DNR Foresters in each DNR Forestry Administrative Area, and is updated on a...

  12. Basic Stand Alone Carrier Line Items PUF

    Data.gov (United States)

    U.S. Department of Health & Human Services — This release contains the Basic Stand Alone (BSA) Carrier Line Items Public Use Files (PUF) with information from Medicare Carrier claims. The CMS BSA Carrier Line...

  13. Seismic design method of free standing rack

    International Nuclear Information System (INIS)

    Taniguchi, Katsuhiko; Okuno, Daisaku; Iwasaki, Akihisa; Nekomoto, Yoshitsugu; Matsuoka, Toshihiro

    2013-01-01

    For high earthquake resistance and ease of installation, free standing racks which are not anchored to the pool floor or walls has been adopted in many countries. Under the earthquake, the response of the free standing rack is highly nonlinear and involves a complex combination of motions (sliding, rocking, twisting, and turning) and impacts between the fuel assemblies and the fuel cell walls, rack-to-rack, and the pit floor and rack pedestals. We carried out seismic experiments on the full-scale rack model in water and dry conditions to obtain the fundamental data about free standing rack (sliding, rocking and turning motions). We have developed the nonlinear dynamic analysis method to predict seismic response for the free standing rack utilizing the full-scale test result and verified the analysis evaluation method of the rack by comparison of test result. (author)

  14. Lisa's Lemonade Stand: Exploring Algebraic Ideas.

    Science.gov (United States)

    Billings, Esther M. H.; Lakatos, Tracy

    2003-01-01

    Presents an activity, "Lisa's Lemonade Stand," that actively engages students in algebraic thinking as they analyze change by investigating relationships between variables and gain experience describing and representing these relationships graphically. (YDS)

  15. Three-dimensional instability of standing waves

    Science.gov (United States)

    Zhu, Qiang; Liu, Yuming; Yue, Dick K. P.

    2003-12-01

    We investigate the three-dimensional instability of finite-amplitude standing surface waves under the influence of gravity. The analysis employs the transition matrix (TM) approach and uses a new high-order spectral element (HOSE) method for computation of the nonlinear wave dynamics. HOSE is an extension of the original high-order spectral method (HOS) wherein nonlinear wave wave and wave body interactions are retained up to high order in wave steepness. Instead of global basis functions in HOS, however, HOSE employs spectral elements to allow for complex free-surface geometries and surface-piercing bodies. Exponential convergence of HOS with respect to the total number of spectral modes (for a fixed number of elements) and interaction order is retained in HOSE. In this study, we use TM-HOSE to obtain the stability of general three-dimensional perturbations (on a two-dimensional surface) on two classes of standing waves: plane standing waves in a rectangular tank; and radial/azimuthal standing waves in a circular basin. For plane standing waves, we confirm the known result of two-dimensional side-bandlike instability. In addition, we find a novel three-dimensional instability for base flow of any amplitude. The dominant component of the unstable disturbance is an oblique (standing) wave oriented at an arbitrary angle whose frequency is close to the (nonlinear) frequency of the original standing wave. This finding is confirmed by direct long-time simulations using HOSE which show that the nonlinear evolution leads to classical Fermi Pasta Ulam recurrence. For the circular basin, we find that, beyond a threshold wave steepness, a standing wave (of nonlinear frequency Omega) is unstable to three-dimensional perturbations. The unstable perturbation contains two dominant (standing-wave) components, the sum of whose frequencies is close to 2Omega. From the cases we consider, the critical wave steepness is found to generally decrease/increase with increasing radial

  16. Stand and within-stand factors influencing Golden-winged Warbler use of regenerating stands in the central Appalachian Mountains

    Directory of Open Access Journals (Sweden)

    Marja H. Bakermans

    2015-06-01

    Full Text Available The Golden-winged Warbler (Vermivora chrysoptera is currently being considered for protected status under the U.S. Endangered Species Act. The creation of breeding habitat in the Appalachian Mountains is considered a conservation priority for this songbird, which is dependent on extensively forested landscapes with adequate availability of young forest. We modeled abundance of Golden-winged Warbler males in regenerating harvested forest stands that were 0-17 years postharvest at both mid-Appalachian and northeast Pennsylvania regional scales using stand and within-stand characteristics of 222 regenerating stands, 2010-2011. Variables that were most influential at the mid-Appalachian scale were different than those in the northeast region. Across the mid-Appalachian ecoregion, the proportion of young forest cover, i.e., shrub/scrub cover, within 1 km of regenerating stands best explained abundance of Golden-winged Warblers. Golden-winged Warbler response was best explained by a concave quadratic relationship in which abundance was highest with 5-15% land in young forest cover. We also found evidence that the amount of herbaceous cover, i.e., the amount of grasses and forbs, within a regenerating stand positively influenced abundance of Golden-winged Warblers. In northeastern Pennsylvania, where young forest cover is found in high proportions, the distance to the nearest regenerating stand best explained variation in abundance of Golden-winged Warblers. Abundance of Golden-winged Warblers was 1500 m away. When modeling within-stand features in the northeast region, many of the models were closely ranked, indicating that multiple variables likely explained Golden-winged Warbler response to within-stand conditions. Based on our findings, we have proposed several management guidelines for land managers interested in creating breeding habitat for Golden-winged Warblers using commercial timber operations. For example, we recommend when managing for

  17. Management alternatives of energy wood thinning stands

    International Nuclear Information System (INIS)

    Heikkilae, Jani; Siren, Matti; Aeijaelae, Olli

    2007-01-01

    Energy wood thinning has become a feasible treatment alternative of young stands in Finland. Energy wood thinnings have been carried out mainly in stands where precommercial thinning has been neglected and the harvesting conditions for industrial wood thinning are difficult. Despite of its positive effects on harvesting costs and on renewable energy potential, whole-tree harvesting has been constantly criticized for causing growth loss. In this paper, the profitability of energy wood thinning was studied in 20 Scots pine-dominated stands where energy wood thinning was carried out. The growth of the stands after thinning was predicted with the help of Motti-stand simulator. Entire rotation time of the stands was simulated with different management alternatives. The intensity of first thinning and recovery level of logging residues varied between alternatives. In order to attain acceptable harvesting conditions, industrial wood thinning had to be delayed. The effect of energy wood thinning on subsequent stem wood growth was almost the same as in conventional thinning. Whole-tree harvesting for energy proved to be profitable alternative if the stumpage price is around 3EUR m -3 , the interest rate is 3% or 5% and the removal of pulpwood is less than 20 m 3 ha -1 . If the harvestable pulpwood yield is over 20 m 3 ha -1 , integrated harvesting of industrial and energy wood or delayed industrial wood harvesting becomes more profitable. (author)

  18. Development of prolonged standing strain index to quantify risk levels of standing jobs.

    Science.gov (United States)

    Halim, Isa; Omar, Abdul Rahman

    2012-01-01

    Many occupations in industry such as metal stamping workers, electronics parts assembly operators, automotive industry welders, and lathe operators require working in a standing posture for a long time. Prolonged standing can contribute to discomfort and muscle fatigue particularly in the back and legs. This study developed the prolonged standing strain index (PSSI) to quantify the risk levels caused by standing jobs, and proposed recommendations to minimize the risk levels. Risk factors associated with standing jobs, such as working posture, muscles activity, standing duration, holding time, whole-body vibration, and indoor air quality, were the basis for developing the PSSI. All risk factors were assigned multipliers, and the PSSI was the product of those multipliers. Recommendations for improvement are based on the PSSI; however, extensive studies are required to validate their effectiveness. multipliers, and the PSSI was the product of those multipliers. Recommendations for improvement are based on the PSSI; however, extensive studies are required to validate their effectiveness.

  19. Dictionary of cotton: Picking & ginning

    Science.gov (United States)

    Cotton is an essential commodity for textiles and has long been an important item of trade in the world’s economy. Cotton is currently grown in over 100 countries by an estimated 100 producers. The basic unit of the cotton trade is the cotton bale which consists of approximately 500 pounds of raw c...

  20. The Influence of Residual Stand Densities on Regeneration in Sugar Maple Stands

    Science.gov (United States)

    Carl H. Tubbs

    1968-01-01

    Studies of regeneration 2, 5, and 10 years after cutting mature and overmature sugar maple stands to several residual densities show that (1) sugar maple is still the predominant species under all stand densities (2) nearly all regeneration reaching larger size classes became established before cutting (3) heavier cuttings (30, 50, and 70 square feet) are more rapidly...

  1. Advance reproduction and other stand characteristics in Pennsylvania and French stands of northern red oak

    Science.gov (United States)

    Kim C. Steiner; Marc D. Abrams; Todd W. Bowersox

    1993-01-01

    The frequent scarcity of northern red oak (NRO) advance reproduction raises questions about its regeneration potential under prevailing stand conditions in eastern North America. In contrast, NRO plantations in France typically contain abundant advance reproduction. The purpose of this study was to document stand conditions in Pennsylvania (PA) and southwestern France...

  2. High-voltage test stand at Livermore

    International Nuclear Information System (INIS)

    Smith, M.E.

    1977-01-01

    This paper describes the present design and future capability of the high-voltage test stand for neutral-beam sources at Lawrence Livermore Laboratory. The stand's immediate use will be for testing the full-scale sources (120 kV, 65 A) for the Tokamak Fusion Test Reactor. It will then be used to test parts of the sustaining source system (80 kV, 85 A) being designed for the Magnetic Fusion Test Facility. Following that will be an intensive effort to develop beams of up to 200 kV at 20 A by accelerating negative ions. The design of the test stand features a 5-MVA power supply feeding a vacuum tetrode that is used as a switch and regulator. The 500-kW arc supply and the 100-kW filament supply for the neutral-beam source are battery powered, thus eliminating one or two costly isolation transformers

  3. Stand development of trembling aspen in Canaan Valley, West Virginia

    Science.gov (United States)

    James S. Rentch; James T. Anderson

    2008-01-01

    In wetlands of Canaan Valley, West Virginia, trembling aspen occurs as a disjunct population well south of its primary natural range. Based on sample data from 15 stands, we found that aspen occurs as nearly monospecific stands or clones. Eight stands had median ages between 30 and 40 yrs, and we suggest that stand initiation was related to changes in land use after...

  4. Future directions in standing-wave photoemission

    Energy Technology Data Exchange (ETDEWEB)

    Gray, Alexander X., E-mail: axgray@temple.edu

    2014-08-15

    Highlights: • Probing magnetic properties at the buried interface with SW-MCD. • Probing electronic structure at the buried interface with resonant SW-XPS and SW-HAXPES. • Probing momentum-resolved electronic structure at a buried interface with SWARPES. • Adding depth resolution to photoemission microscopy with standing-wave excitation. • Standing-wave localization, total reflection and waveguide effects. - Abstract: Over the past decade, standing-wave photoemission (SW-XPS) has evolved into a powerful and versatile non-destructive technique for probing element-specific electronic, magnetic, and structural properties of buried layers and interfaces with sub-nanometer depth resolution. In this article, I will discuss several promising future directions in this emergent field stemming from experimental and theoretical studies wherein SW-XPS is combined with other X-ray techniques, such as magnetic circular dichroism (MCD), hard X-ray photoemission spectroscopy (HAXPES), angle-resolved photoemission (ARPES), and photoemission microscopy (PEEM), adding extra dimensions to the measurement and thus widening the scope of scientific and technological questions accessible via the use of standing waves. I will further discuss examples of recently developed methods for X-ray standing-wave data analysis, which yield layer-resolved matrix-element-weighted densities of states at interfaces as well as Ångstrom-level changes in periodicity of synthetic superlattices. Finally, I will explore the possibility of localizing the standing waves near the surface and within a buried layer by the use of aperiodic superlattices, total reflection, and X-ray waveguide effects.

  5. Future directions in standing-wave photoemission

    International Nuclear Information System (INIS)

    Gray, Alexander X.

    2014-01-01

    Highlights: • Probing magnetic properties at the buried interface with SW-MCD. • Probing electronic structure at the buried interface with resonant SW-XPS and SW-HAXPES. • Probing momentum-resolved electronic structure at a buried interface with SWARPES. • Adding depth resolution to photoemission microscopy with standing-wave excitation. • Standing-wave localization, total reflection and waveguide effects. - Abstract: Over the past decade, standing-wave photoemission (SW-XPS) has evolved into a powerful and versatile non-destructive technique for probing element-specific electronic, magnetic, and structural properties of buried layers and interfaces with sub-nanometer depth resolution. In this article, I will discuss several promising future directions in this emergent field stemming from experimental and theoretical studies wherein SW-XPS is combined with other X-ray techniques, such as magnetic circular dichroism (MCD), hard X-ray photoemission spectroscopy (HAXPES), angle-resolved photoemission (ARPES), and photoemission microscopy (PEEM), adding extra dimensions to the measurement and thus widening the scope of scientific and technological questions accessible via the use of standing waves. I will further discuss examples of recently developed methods for X-ray standing-wave data analysis, which yield layer-resolved matrix-element-weighted densities of states at interfaces as well as Ångstrom-level changes in periodicity of synthetic superlattices. Finally, I will explore the possibility of localizing the standing waves near the surface and within a buried layer by the use of aperiodic superlattices, total reflection, and X-ray waveguide effects

  6. Free-Standing, Flexible, Superomniphobic Films.

    Science.gov (United States)

    Vahabi, Hamed; Wang, Wei; Movafaghi, Sanli; Kota, Arun K

    2016-08-31

    Fabrication of most superomniphobic surfaces requires complex process conditions or specialized and expensive equipment or skilled personnel. In order to circumvent these issues and make them end-user-friendly, we developed the free-standing, flexible, superomniphobic films. These films can be stored and delivered to the end-users, who can readily attach them to virtually any surface (even irregular shapes) and impart superomniphobicity. The hierarchical structure, the re-entrant texture, and the low solid surface energy render our films superomniphobic for a wide variety of liquids. We demonstrate that our free-standing, flexible, superomniphobic films have applications in enhanced chemical resistance and enhanced weight bearing.

  7. [Occupational standing vibration rate and vibrational diseases].

    Science.gov (United States)

    Karnaukh, N G; Vyshchipan, V F; Haumenko, B S

    2003-12-01

    Occupational standing vibration rate is proposed in evaluating a degree of impairment of an organism activity. It will allow more widely to introduce specification of quality and quantity in assessment of the development of vibrational disease. According out-patient and inpatient obtained data we have established criterial values of functional changes in accordance with accumulated occupational standing vibration rate. The nomogram was worked out for defining a risk of the development of vibrational disease in mine workers. This nomogram more objectively can help in diagnostics of the disease.

  8. Stand alone photovoltaic systems: guarantee of results

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    This study aims to provide a guarantee of results for system performance for users of stand-alone photovoltaic (PV) systems, which have no back-up generator. The appropriate main performance criterion for PV systems is that a specified load is supplied with power either continuously or intermittently whenever the load requires power. A methodology to evaluate the power availability of stand-alone PV systems has been developed as part of the project, which encompasses power losses due to weather variations. The guarantee of results produced allows users to compare system designs from different manufacturers. (UK)

  9. Detecção e seleção de talentos na ginástica artística feminina: a perspectiva dos técnicos brasileiros

    Directory of Open Access Journals (Sweden)

    Myrian Nunomura

    2014-04-01

    Full Text Available Este artigo tem por objetivo apresentar e discutir a detecção e a seleção de talentos na Ginástica Artística Feminina com enfoque para os aspectos que norteiam as condutas dos técnicos brasileiros. Entrevistamos 34 técnicos de 29 instituições distribuídas no Brasil. Observamos que os meios utilizados para detectar e selecionar os talentos na modalidade privilegiam a idade de ingresso, as características antropométricas e os testes físico-motores. Porém, sabemos que os determinantes do sucesso no esporte são multifatoriais e, por vezes, as avaliações transversais utilizadas não contemplam todos os fatores que contribuem para a obtenção de bons resultados no alto rendimento.

  10. Prática da ginástica laboral por trabalhadores das indústrias do Rio Grande do Sul, Brasil Stretching programs among industrial workers from the state of Rio Grande do Sul, Brazil

    Directory of Open Access Journals (Sweden)

    Luana Callegaro Rossato

    2013-03-01

    Full Text Available O presente estudo identificou a prevalência e os fatores associados à prática de ginástica laboral por trabalhadores da indústria no Estado do Rio Grande do Sul, Brasil. Realizou-se análise secundária dos dados de um estudo de delineamento transversal, com amostra probabilística de 2.265 trabalhadores, de ambos os sexos. O instrumento de pesquisa foi o questionário autoadministrado "Estilo de vida e hábitos de lazer dos trabalhadores das indústrias brasileiras", previamente validado. A variável dependente foi a prática de ginástica laboral, definida pela resposta positiva à questão: "Você participa do programa de ginástica na empresa (ginástica laboral?". Foram coletadas informações demográficas, socioeconômicas, comportamentais e relacionadas à saúde, como potenciais fatores associados. Na análise de dados, empregou-se o teste Qui-quadrado de Pearson e o modelo de regressão de Poisson com variância robusta, nas análises bruta e ajustada, respectivamente. A prática de ginástica laboral foi referida por 40,3% dos respondentes (IC95%: 38,2; 42,3, sendo mais prevalente nos trabalhadores do sexo feminino, com maiores níveis de escolaridade, naqueles mais ativos no lazer e que relatavam menores intensidades de esforço no trabalho. Não se observou associação da variável dependente com idade, estado civil, renda familiar bruta, tabagismo, autopercepção de saúde e autopercepção do nível de estresse. Programas de ginástica laboral devem desenvolver estratégias de promoção da saúde que priorizem subgrupos de trabalhadores menos envolvidos, em especial, indivíduos do sexo masculino e com menor escolaridade. Desse modo, será possível reduzir as disparidades, beneficiando trabalhadores, independentemente de suas características sociodemográficas, a melhores condições saúde e bem-estar no ambiente das indústrias.We evaluated the prevalence and factors associated with participation on stretching programs

  11. Introducing sit-stand desks increases classroom standing time among university students.

    Science.gov (United States)

    Jerome, Matthew; Janz, Kathleen F; Baquero, Barbara; Carr, Lucas J

    2017-12-01

    Excessive sedentary behavior has been associated with many negative health outcomes. While an understudied health topic, there is evidence that university students are excessively sedentary. Sit-stand desks have been shown to reduce sedentary time among pre-university students (ages 5-18 years) and sedentary workers but have not been tested in university classrooms. This study tested the effects of introducing sit-stand desks into a university classroom on student's classroom sitting and standing behaviors. Using a cross-over design, students received access to both traditional seated desks and sit-stand desks for six weeks. Data were collected between September and December, 2016. We recruited 304 healthy undergraduate university students enrolled in one of two small (25 seats) classrooms at a large Midwestern university during the fall of 2016. Average minutes of standing/hour/student, average percent class time spent standing, and the number of sit-stand transitions/student/hour were directly observed with video camera surveillance. Participants stood significantly more (p classrooms as an approach to reduce sedentary behaviors of university students.

  12. Learning to Stand: The Acceptability and Feasibility of Introducing Standing Desks into College Classrooms

    Directory of Open Access Journals (Sweden)

    Roberto M. Benzo

    2016-08-01

    Full Text Available Prolonged sedentary behavior is an independent risk factor for multiple negative health outcomes. Evidence supports introducing standing desks into K-12 classrooms and work settings to reduce sitting time, but no studies have been conducted in the college classroom environment. The present study explored the acceptability and feasibility of introducing standing desks in college classrooms. A total of 993 students and 149 instructors completed a single online needs assessment survey. This cross-sectional study was conducted during the fall semester of 2015 at a large Midwestern University. The large majority of students (95% reported they would prefer the option to stand in class. Most students (82.7% reported they currently sit during their entire class time. Most students (76.6% and instructors (86.6% reported being in favor of introducing standing desks into college classrooms. More than half of students and instructors predicted having access to standing desks in class would improve student’s “physical health”, “attention”, and “restlessness”. Collectively, these findings support the acceptability of introducing standing desks in college classrooms. Future research is needed to test the feasibility, cost-effectiveness and efficacy of introducing standing desks in college classrooms. Such studies would be useful for informing institutional policies regarding classroom designs.

  13. Long standing intra oral acid burn

    NARCIS (Netherlands)

    Kumar, V.V.; Ebenezer, S.; Lobbezoo, F.

    2015-01-01

    Oral burn due to ingestion of corrosive substances can bring about debilitating consequences. It often brings mortality, and the survivors can have severe impairment of functions, especially in relation to the stomatognathic and gastrointestinal systems. This article presents a long-standing case

  14. Estimating white trunk rot in aspen stands

    Science.gov (United States)

    Alan C. Jones; Michael E. Ostry

    1998-01-01

    Advanced decay caused by Phellinus tremulae was estimated in 295 trembling aspen on 30 plots in 2 Minnesota counties using existing inventory guides, and then measured by felling and sectioning the trees. In standing trees, decay volume was underestimated by 38% compared to measured decay volume in felled trees. The most reliable external indicator...

  15. Large optics inspection, tilting, and washing stand

    Science.gov (United States)

    Ayers, Marion Jay [Brentwood, CA; Ayers, Shannon Lee [Brentwood, CA

    2010-08-24

    A large optics stand provides a risk free means of safely tilting large optics with ease and a method of safely tilting large optics with ease. The optics are supported in the horizontal position by pads. In the vertical plane the optics are supported by saddles that evenly distribute the optics weight over a large area.

  16. Direct sampling for stand density index

    Science.gov (United States)

    Mark J. Ducey; Harry T. Valentine

    2008-01-01

    A direct method of estimating stand density index in the field, without complex calculations, would be useful in a variety of silvicultural situations. We present just such a method. The approach uses an ordinary prism or other angle gauge, but it involves deliberately "pushing the point" or, in some cases, "pulling the point." This adjusts the...

  17. Ranking Thinning Potential of Lodgepole Pine Stands

    OpenAIRE

    United States Department of Agriculture, Forest Service

    1987-01-01

    This paper presents models for predicting edge-response of dominant and codominant trees to clearing. Procedures are given for converting predictions to a thinning response index, for ranking stands for thinning priority. Data requirements, sampling suggestions, examples of application, and suggestions for management use are included to facilitate use as a field guide.

  18. IMS Learning Design: De stand van zaken

    NARCIS (Netherlands)

    Tattersall, Colin; Manderveld, Jocelyn

    2005-01-01

    Tattersall, C. & Manderveld, J. (2004) IMS Learning Design: De stand van zaken In: Gorissen, P., Manderveld, J., Benneker, F. & Cordewener, B. Leertechnologie in de Lage Landen (pp. 31-33). Utrecht, Stichting Surf. Ook beschikbaar in dspace: http://hdl.handle.net/1820/270

  19. Construction alternatives for free-standing facilities.

    Science.gov (United States)

    Brown, G

    1990-01-01

    Many hospitals are exploring free-standing facilities as an option for providing more efficient imaging services. Mr. Brown discusses the pros and cons of an emerging building technology, manufactured construction, in which building and site preparation are done simultaneously. He presents the criteria managers should use to make a knowledgeable decision.

  20. AA, wide quadrupole on measurement stand

    CERN Multimedia

    CERN PhotoLab

    1981-01-01

    Please look up 8101024 and 8103203 first. Wide quadrupole (QFW, QDW) with end-shims and shimming washers on the measurement stand. With the measurement coil one measured the harmonics of the magnetic field, determined the magnetic centre, and catalogued the effect of washer constellations.

  1. Standing waves in fiber-optic interferometers

    NARCIS (Netherlands)

    De Haan, V.; Santbergen, R.; Tijssen, M.; Zeman, M.

    2011-01-01

    A study is presented giving the response of three types of fiber-optic interferometers by which a standing wave through an object is investigated. The three types are a Sagnac, Mach–Zehnder and Michelson–Morley interferometer. The response of the Mach–Zehnder interferometer is similar to the Sagnac

  2. Standing stability evaluation using a triaxial accelerometer

    NARCIS (Netherlands)

    Mayagoitia, Ruth E.; Mayagoitia, R.E.; Lötters, Joost Conrad; Lotters, Joost Conrad; Veltink, Petrus H.

    1996-01-01

    A triaxial accelerometer is placed at the back of the subject at the height of the center of mass. Force plate data are collected simultaneously. Subjects stand in a comfortable position with eyes open, eyes closed and doing cognitive tasks; and with feet together with eyes open and closed. The

  3. Standing on the shoulders of giants.

    Science.gov (United States)

    Romanovsky, Andrej A

    2014-01-01

    In this editorial, the author explains that the journal Temperature stands on the shoulders of giants-prominent scientists of the past and current members of the Temperature community. Temperature also uses the best tools, such as Google Scholar profiles. The editorial includes a new puzzle: why does warm water freeze faster than cold water?

  4. The ambiguity of standing in standing devices: a qualitative interview study concerning children and parents experiences of the use of standing devices.

    Science.gov (United States)

    Nordström, Birgitta; Näslund, Annika; Ekenberg, Lilly; Zingmark, Karin

    2014-10-01

    The aim of this study was to describe children's and parents' experiences of the significance of standing in a standing device. Individual interviews were performed with six children/teenagers (aged 7-19 years) and 14 parents. The interviews were transcribed and analyzed using a qualitative content analysis. The analysis resulted in the major theme, the duality of uprightness and the related themes: (1) the instrumental dimension of standing; (2) the social dimension of standing; and (3) the ambivalent dimension of standing. Each of the themes comprised several subthemes. There is an inherent duality related to the use of a standing device. Standing in a standing device was seen as a treatment of body structures and functions, as well as a possible source of pain. Standing was considered to influence freedom in activities and participation both positively and negatively. The parents experienced that standing influenced other peoples' views of their child, while the children experienced standing as a way to extend the body and as something that gave them benefits in some activities. Physiotherapists working with children should take into account both the social and physical dimensions of using a standing device and consider both the child's and the parents' views.

  5. Transformation of solar radiation in Norway spruce stands into produced biomass - the effect of stand density

    International Nuclear Information System (INIS)

    Marková, I.; Marek, M.V.; Pokorný, R.

    2011-01-01

    The present paper is focused on the assessment of the effects of stand density and leaf area development on radiation use efficiency in the mountain cultivated Norway spruce stand. The young even-aged (17-years-old in 1998) plantation of Norway spruce was divided into two experimental plots differing in their stand density in 1995. During the late spring of 2001 next cultivating high-type of thinning of 15% intensity in a reduction of stocking density was performed. The PAR regime of investigated stands was continually measured since 1992. Total aboveground biomass (TBa) and TBa increment were obtained on the basis of stand inventory. The dynamic of LAI development showed a tendency to be saturated, i.e. the LAI value close to 11 seems to be maximal for the local conditions of the investigated mountain cultivated Norway spruce stand in the Beskids Mts. Remarkable stimuli (up to 17%) of LAI formation were started in 2002, i.e. as an immediate response to thinning. Thus, the positive effect of thinning on LAI increase was confirmed. The data set of absorbed PAR and produced TBa in the period 1998-2003 was processed by the linear regression of Monteith's model, which provided the values of the coefficient of solar energy conversion efficiency into biomass formation. The differences in biomass formation values between the dense and sparse plot after thinning amounted to 18%

  6. Residual liquefaction of seabed under standing waves

    DEFF Research Database (Denmark)

    Kirca, V.S. Ozgur; Sumer, B. Mutlu; Fredsøe, Jørgen

    2013-01-01

    This paper presents the results of an experimental study of the seabed liquefaction beneath standing waves. Silt (with d50 =0.070mm) was used in the experiments. Two kinds of measurements were carried out: pore water pressure measurements and water surface elevation measurements. These measurements...... were synchronized with video recording of the liquefaction process from the side. The ranges of the various quantities in the experiments were wave height H= 5.9-12.0 cm, wave period T= 1.09s, and water depth h=30 cm. The experiments show that the seabed liquefaction under standing waves, although...... qualitatively similar, show features different from that caused by progressive waves. The pore water pressure builds up (or accumulated) in the areas around the node and subsequently spreads out toward the antinodes. The experimental results imply that this transport is caused by a diffusion mechanism...

  7. Modeling natural regeneration biomass of Pinus stand

    Directory of Open Access Journals (Sweden)

    Rafael Cubas

    2016-09-01

    Full Text Available Reliable biomass data are very important in the evaluation of ecosystems, and help in understanding the contribution of forests in climate change. Variables that describe the size of the tree, like diameter and height are directly associated with biomass, which allows the use of regression models to estimate this element. Therefore, this study aimed to estimate by regression models, the biomass of different compartments of natural regeneration of trees of a Pinus taeda L. stand. The data were obtained through direct destructive method, using 100 randomly selected trees in the understory of a stand of Pinus taeda. We analyzed three arithmetical models, three logarithmic and two models developed by Stepwise process. Logarithmic equations developed by Stepwise procedure showed the best estimates of total and stems biomass. However, for needles and twigs compartments the best adjust was observed with Husch model and for root biomass Berkhout model proved to be the most suitable.

  8. The standing advisory group on safeguards implementation

    International Nuclear Information System (INIS)

    Jennekens, J.H.F.

    1982-09-01

    In 1975 the Director General of the IAEA called together ten persons from member states with nuclear programs at varying stages of development to form the Standing Advisory Group on Safeguards Implementation. The group was later expanded to twelve. The Director General asked the group to evaluate the technical objectives of Agency safeguards, assess the effectiveness and efficiency of specific safeguards operating methods in meeting these technical objectives, advise on techniques to be employed in safeguards operations, and recommend areas where further work is needed. This paper reviews the work of the Standing Advisory Group on Safeguards Implementation since its formation in 1975, summarizes the subjects that have been examined and the advice rendered, and outlines the problem areas requiring further study

  9. Nonlinear theory of localized standing waves

    OpenAIRE

    Denardo, Bruce; Larraza, Andrés; Putterman, Seth; Roberts, Paul

    1992-01-01

    An investigation of the nonlinear dispersive equations of continuum mechanics reveals localized standing-wave solutions that are domain walls between regions of different wave number. These states can appear even when the dispersion law is a single-valued function of the wave number. In addition, we calculate solutions for kinks in cutoff and noncutoff modes, as well as cutoff breather solitons. Division of Engineering and Geophysics of the Office of Basic Energy Science of U.S. DOE for su...

  10. Beam instrumentation for an ISOL test stand

    International Nuclear Information System (INIS)

    Mackenzie, G.H.; Dombsky, M.; Rawnsley, W.; Stanford, G.; Yin, Y.; Novikov, A.

    1995-09-01

    TRIUMF is constructing a test bed for the first stages of the proposed TISAC accelerated radioactive beam facility. The authors will present the requirements for the diagnostic system for this test stand and describe the design and development work underway. Scintillators, beamstops and a Faraday Cup have been tested using stable, mass analyzed, 12 keV beams of ions from mass 14 to 132. The design of a linear drive, with 10 microm resolution, for scanning wires and slits has begun

  11. Beam instrumentation for an ISOL test stand

    International Nuclear Information System (INIS)

    Mackenzie, G.H.; Dombsky, M.; Rawnsley, W.; Stanford, G.; Yin, Y.; Novikov, A.

    1995-09-01

    TRIUMF is constructing a test bed for the first stages of the proposed TISAC accelerated radioactive beam facility. We will present the requirements for the diagnostic system for this test stand and describe the design and development work underway. Scintillators, beamstops and Faraday Cup have been tested using stable, mass analyzed, 12 keV beams of ions from mass 14 to 132. The design of a linear drive, with 10 μm resolution, for scanning wires and slits has begun. (author)

  12. Down force calibration stand test report

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    The Down Force Calibration Stand was developed to provide an improved means of calibrating equipment used to apply, display and record Core Sample Truck (CST) down force. Originally, four springs were used in parallel to provide a system of resistance that allowed increasing force over increasing displacement. This spring system, though originally deemed adequate, was eventually found to be unstable laterally. For this reason, it was determined that a new method for resisting down force was needed

  13. Test Stand for Linear Induction Accelerator Optimization

    International Nuclear Information System (INIS)

    Ong, M; DeHope, B; Griffin, K; Goerz, D; Kihara, R; Vogtlin, G; Zentler, J M; Scarpetti, R

    2003-01-01

    Lawrence Livermore National Laboratory has designed and constructed a test stand to improve the voltage regulation in our Flash X-Ray (FXR) accelerator cell. The goal is to create a more mono-energetic electron beam that will create an x-ray source with a smaller spot size. Studying the interaction of the beam and pulse-power system with the accelerator cell will improve the design of high-current accelerators at Livermore and elsewhere. On the test stand, a standard FXR cell is driven by a flexible pulse-power system and the beam current is simulated with a switched center conductor. The test stand is fully instrumented with high-speed digitizers to document the effect of impedance mismatches when the cell is operated under various full-voltage conditions. A time-domain reflectometry technique was also developed to characterize the beam and cell interactions by measuring the impedance of the accelerator and pulse-power component. Computer models are being developed in parallel with the testing program to validate the measurements and evaluate different design changes. Both 3D transient electromagnetic and circuit models are being used

  14. O Modelo de Carga Externa em Ginástica Artística Feminina de Alto Rendimento. A estrutura e as tendências evolutivas dos exercícios de competiçãoem Paralelas Assimétricas.

    OpenAIRE

    Ferreirinha, José

    2011-01-01

    Embora a Ginástica Artística seja muitas vezes referida como uma modalidade associada a grandes volumes e intensidades de treino, são escassos os dados objectivamente mensurados que fundamentem tais referências. Ao nível da carga externa, apenas são feitas algumas referências que caracterizam as sessões de treino, na sua duração, frequência e quantidades de elementos e exercícios efectuados. A Federação Internacional de Ginástica também tem efectuado relatórios após as grandes competições int...

  15. Stand structure and regeneration of harvested Araucaria araucana ...

    African Journals Online (AJOL)

    Stand structure and regeneration of harvested Araucaria araucana–Nothofagus stands in central Chile. Rafael M Navarro-Cerrillo, Fernando Olave, Francisco Moreno, Sergio de Miguel, Margarita Clemente ...

  16. Forest evaporation models: Relationships between stand growth and evaporation

    CSIR Research Space (South Africa)

    Le Maitre, David C

    1997-06-01

    Full Text Available The relationships between forest stand structure, growth and evaporation were analysed to determine whether forest evaporation can be estimated from stand growth data. This approach permits rapid assessment of the potential impacts of afforestation...

  17. Tropical forest biomass estimation from truncated stand tables.

    Science.gov (United States)

    A. J. R. Gillespie; S. Brown; A. E. Lugo

    1992-01-01

    Total aboveground forest biomass may be estimated through a variety of techniques based on commercial inventory stand and stock tables. Stand and stock tables from tropical countries commonly omit trees bellow a certain commercial limit.

  18. 21 CFR 880.2700 - Stand-on patient scale.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Stand-on patient scale. 880.2700 Section 880.2700... Devices § 880.2700 Stand-on patient scale. (a) Identification. A stand-on patient scale is a device intended for medical purposes that is used to weigh a patient who is able to stand on the scale platform...

  19. Lesões desportivas na ginástica artística: estudo a partir de morbidade referida Sports injuries in artistic gymnastics: a study from referred morbidity

    Directory of Open Access Journals (Sweden)

    Rosangela Akemi Hoshi

    2008-10-01

    Full Text Available INTRODUÇÃO: Os níveis de exigência biomecânica devidos ao alto grau de dificuldade na realização de gestos fazem da ginástica artística (GA uma modalidade com elevado risco de lesões. Assim, é necessário que os aspectos a elas relacionados sejam controlados. OBJETIVO: Analisar a ocorrência de lesões na Ginástica Artística, associando-as a fatores de risco específicos da modalidade e do atleta, a partir de inquérito de morbidade referida. MÉTODOS: Foram entrevistados 54 ginastas, recrutados ao acaso, classificados segundo o nível competitivo em duas categorias: regional e nacional. Utilizou-se o inquérito de morbidade referida (IMR com a finalidade de reunir dados sobre a natureza da lesão, região corporal e aparelho ginástico. Os dados foram organizados e apresentados sob a forma de distribuição de freqüências e as variáveis, analisadas segundo nível de associação a partir do teste de Goodman para contrastes entre populações multinomiais, considerando significante o valor P INTRODUCTION: The levels of biomechanical demands due to the high level of difficulty in the gestures accomplishment make Artistic Gymnastics (AG a modality with high risk of injuries. Thus, it is necessary that the aspects concerned with them are controlled. OBJECTIVE: To analyze the occurrence of injuries in artistic gymnastics, associating them with specific risk factors of the modality and of the athlete from reported morbidity survey. METHODS: 54 gymnasts randomly recruited have been interviewed and classified according to their competitive level into two categories: regional and national. The reported morbidity questionnaire (RMQ was used with the purpose to collect data on the injury's nature, body region and gymnastic apparatus. Data were organized and presented under frequency distribution and analyzed variables. The variables were analyzed according to their level of association from the Goodmann's test for contrasts between

  20. Relationship of stand age to streamwater nitrate in New Hampshire

    Science.gov (United States)

    William B. Leak; C. Wayne Martin

    1975-01-01

    Streamwater nitrate content of six watersheds during spring and summer was apparently related to stand age or age since disturbance. Nitrate concentration averaged 10.3 ppm right after cutting, dropped to a trace in medium-aged stands, and then rose again to a maximum of 4.8 ppm as stands became overmature.

  1. Production economics of harvesting young hardwood stands in central Appalachia

    Science.gov (United States)

    Yaoxiang Li; Jingxin Wang; Gary W. Miller; Joe McNeel

    2004-01-01

    Three harvesting systems of chainsaw/cable skidder, fell-buncher/grapple skidder, and harvester/forwarder were simulated in harvesting three hardwood stands of 30 to 50 years old in central Appalachia. Stands were generated by using a stand generator and harvesting prescriptions included clearcut, shelterwood cut, selective cut, diameter limit cut, and crop tree...

  2. A 3D stand generator for central Appalachian hardwood forests

    Science.gov (United States)

    Jingxin Wang; Yaoxiang Li; Gary W. Miller

    2002-01-01

    A 3-dimensional (3D) stand generator was developed for central Appalachian hardwood forests. It was designed for a harvesting simulator to examine the interactions of stand, harvest, and machine. The Component Object Model (COM) was used to design and implement the program. Input to the generator includes species composition, stand density, and spatial pattern. Output...

  3. Effect of two Notebook stands on work posture and productivity

    NARCIS (Netherlands)

    Könemann, R.; Kuijt-Evers, L.F.M.; Lingen, P. van; Sauvage, S.; Hallbeck, S.

    2009-01-01

    The aim of this study was to investigate the effect of using a notebook stand on the physical load when working with a notebook in a home environment. Sixteen subjects evaluated working with a notebook by performing three different tasks using two notebook stands and without using a notebook stand.

  4. The zero inflation of standing dead tree carbon stocks

    Science.gov (United States)

    Christopher W. Woodall; David W. MacFarlane

    2012-01-01

    Given the importance of standing dead trees in numerous forest ecosystem attributes/processes such as carbon (C) stocks, the USDA Forest Service’s Forest Inventory and Analysis (FIA) program began consistent nationwide sampling of standing dead trees in 1999. Modeled estimates of standing dead tree C stocks are currently used as the official C stock estimates for the...

  5. Stocking equations for regeneration in mixed oak stands

    Science.gov (United States)

    Songlin Fei; Kim C. Steiner; James C. Finley

    2007-01-01

    Regeneration stocking equations for mixed-oak stands were developed based on data collected from nearly 14,000 plots in the central Appalachians. Maximum stand density was identified by plotting aggregate height against number of seedlings per plot, and was used as the reference level of the average maximum stand density (100 percent stocking or A-level stocking)....

  6. Practical research of free standing rack. Seismic experiment study on full scale free standing rack

    International Nuclear Information System (INIS)

    Iwasaki, Akihisa; Nekomoto, Yoshitsugu; Morita, Hideyuki; Taniguchi, Katsuhiko; Okuno, Daisaku; Matsuoka, Toshihiro; Chigusa, Naoki

    2015-01-01

    The spent fuel taken out of a plant reactor is temporarily stored in a spent fuel rack. This fuel will often have to be stored in the rack for long periods before it can be moved to a reprocessing facility. Therefore, the spent fuel rack must have a high tolerance against big seismic loads. The free standing spent fuel rack has been developed as the optimal equipment meeting these requirements. It can be placed on the spent fuel pool floor without fixation to any support structure. Response of the free standing rack is reduced by the effect of the water and friction force on the spent fuel pool floor. For nuclear plant safety, it is necessary to understand the free standing rack behavior under earthquake in pools to verify the design of free standing racks and peripheral components. Several tests on a shaking table have been conducted on full-scale one free standing rack in air and in water, and sliding and rocking have been measured. The rack response is very complex and the study necessitates to take into account the sliding, the rocking, the effect of the water and of the arrangement of the fuel assemblies inside. (author)

  7. Desenvolvimento e avaliação de um descaroçador e prensa enfardadeira itinerantes para o beneficiamento do algodão Development of a mobile gin and baler press for cotton

    Directory of Open Access Journals (Sweden)

    Jeane F. Jerônimo

    2013-03-01

    Full Text Available Novas tecnologias vêm sendo incorporadas ao sistema produtivo da cotonicultura brasileira, visando verticalizar a produção por meio do beneficiamento do algodão em caroço possibilitando, aos produtores ou associações, a agregação de valor à sua produção. Objetivou-se então, com o presente trabalho, desenvolver e avaliar um equipamento de beneficiamento composto de descaroçador e prensa enfardadeira itinerantes. O descaroçador se compõe de: limpador, cilindro de serras, cilindro de escovas, condensador e rolo. A prensa enfardadeira é constituída de chapas de prensagem, cilindros hidráulicos, bomba hidráulica, válvula de controle de acionamento, dispositivos de filtragem do óleo hidráulico e manômetro. Esses equipamentos são montados sobre um reboque composto por chassi de cantoneiras em U, quatro rodas de aro 13, pontas de eixo, dois feixes de cinco molas, lastro em chapa de ferro e sistema de frenagem. Na avaliação e validação do conjunto pelos cotonicultores, este conjunto recebeu o conceito "muito bom" quanto ao rendimento do descaroçador, o peso do fardo e em relação à qualidade da fibra obtida. A qualidade da fibra obtida com o conjunto descaroçador e prensa enfardadeira atendeu aos padrões da indústria têxtil.New technologies have been incorporated into the Brazilian cotton production system, in order to verticalize the production through processing, allowing the producers or associations to add value to their production. Thus, the present study aimed to develop and evaluate processing equipment composed of mobile gin and baler press. The ginner consists of cleaner, saw cylinder, cylinder brushes, condenser and coil. The baler press is constituted of pressing sheets, hydraulic cylinders, hydraulic pump, control valve actuation, devices for filtering hydraulic oil and manometer. These devices are mounted on a trailer chassis composed of U-shaped angle iron chassis, four wheels (rim 13, shaft ends, two

  8. Stand-alone photovoltaic applications. Lessons learned

    International Nuclear Information System (INIS)

    Loois, G.; Van Hemert, B.

    1999-02-01

    The IEA Photovoltaic Power Systems Programme (PVPS) is one of the collaborative R and D agreements established within the IEA. The objective of Task III is to promote and facilitate the exchange of information and experiences in the field of PV Systems in Stand-alone and Island Applications (SAPV). The book focuses on the practical experiences gained, and does not aim to provide a complete manual on SAPV. When Task III started its activities in 1993, a collection of 50 'State of the art' projects was published in the book 'Examples of Stand-Alone Photovoltaic Systems'. This publication marked the base line for the work of the task. Now, in 1998, the showcases from each country demonstrate the lessons learned in five years of cooperation. The book consists of two parts. The first part contains eight chapters dealing with a specific aspect of stand-alone PV. The second part introduces 14 national showcase projects in a systematic presentation. Each chapter and showcase can be read independently from the rest of the book. Chapter 2, contributed by The Netherlands, analyses the market for stand-alone PV systems. It gives an overview of the 'traditional' application of stand-alone PV, which is the electrification of remote buildings and which has been addressed in depth in other publications. The focus is on the market niches of service applications that are also interesting for more densely populated areas, e.g. in industrialised countries. The United Kingdom illustrates the economic aspects in Chapter 3. Cost comparisons are made, but more important is the illustration of the non-financial considerations that make PV the preferred choice as a power source for many applications. Switzerland explores in Chapter 4 (financing aspects) different financing mechanisms, and financial policies used to overcome the initial cost barrier. Most of these approaches have been applied in developing countries rather than in the western world. Using various examples from all over the

  9. Stand development and yields of Appalachian hardwood stands managed with single-tree selection for at least 30 years

    Science.gov (United States)

    Neil I Lamson; H. Clay Smith; H. Clay Smith

    1991-01-01

    Appalachian hardwood stands in West Virginia were managed for 30 or more years using single-tree selection regeneration practices. Stand yield data suggest that current stand growth will provide economical harvest cuts for several future cutting cycles. This case study indicates that the single-tree selection practice has potential for landowners who want to maintain...

  10. Stand quality management in a late-rotation, red oak-sweetgum stand in east Mississippi: preliminary results following thinning

    Science.gov (United States)

    James S. Meadows; Daniel A. Skojac

    2012-01-01

    Stand quality management is a new management strategy in which thinning prescriptions are based solely on tree quality rather than a quantitative level of residual stand density. As long as residual density falls within fairly broad limits, prescriptions are based on tree quality alone. We applied four thinning prescriptions based on stand quality management, along...

  11. [Effects of crop tree release on stand growth and stand structure of Cunninghamia lanceolata plantation].

    Science.gov (United States)

    Wu, Jian-qiang; Wang, Yi-xiang; Yang, Yi; Zhu, Ting-ting; Zhu, Xu-dan

    2015-02-01

    Crop trees were selected in a 26-year-old even-aged Cunninghamia lanceolata plantation in Lin' an, and compared in plots that were released and unreleased to examine growth and structure responses for 3 years after thinning. Crop tree release significantly increased the mean increments of diameter and volume of individual tree by 1.30 and 1.25 times relative to trees in control stands, respectively. The increments of diameter and volume of crop trees were significantly higher than those of general trees in thinning plots, crop trees and general trees in control plots, which suggested that the responses from different tree types to crop tree release treatment were different. Crop tree release increased the average distances of crop trees to the nearest neighboring trees, reducing competition among crop trees by about 68.2%. 3-year stand volume increment for thinning stands had no significant difference with that of control stands although the number of trees was only 81.5% of the control. Crop trees in thinned plots with diameters over than 14 cm reached 18.0% over 3 years, compared with 12.0% for trees without thinning, suggesting that crop tree release benefited the larger individual trees. The pattern of tree locations in thinning plots tended to be random, complying with the rule that tree distribution pattern changes with growth. Crop tree release in C. lanceolata plantation not only promoted the stand growth, but also optimized the stand structure, benefiting crop trees sustained rapid growth and larger diameter trees production.

  12. Construction of an automated table standing

    International Nuclear Information System (INIS)

    Neira, R E; Barbero, M D; Di Giulio, E A; Folco, J F; Jiménez, G F

    2011-01-01

    In this paper, the construction of an upright stretcher designed for patients in rehabilitation. The standing back to patients' expectations of therapeutic improvement, allowing correct all the troubles of a passive long. It has been shown that this table favors not only physically but also has a psychological reach beyond the scope of physical therapy and strongly affects the recovery. At the same time, the use of an upright stretcher greatly decreases the biomechanical disorders of hospital staff in the process of recovery. Thus the problem of rehabilitation of trafficking in a comprehensive way which not only focuses on the patient's undivided attention but also includes medical and auxiliary personnel.

  13. The scientific dating of standing buildings.

    Science.gov (United States)

    Alcock, Nathaniel W

    2017-11-17

    The techniques of dendrochronology (tree-ring dating) and radiocarbon (14C) dating are described, as they are applied to historic buildings. Both rely on determining the felling dates of the trees used in their construction. For dendrochronology, the construction of master chronologies and the matching of individual ring-width sequences to them is described and, for radiocarbon dating, the use of tree-ring results in calibration. Results of dating are discussed, ranging from the cathedrals of Peterborough and Beauvais and the development of crown-post roof structures, to the dating and identification of standing medieval peasant houses, particularly those built using cruck construction.

  14. Glass temperatures in free-standing canisters

    International Nuclear Information System (INIS)

    Hardy, B.J.; Hensel, S.J.

    1993-01-01

    The waste-forms produced by the Defense Waste Processing Facility (DWPF) are subject to the requirements of the Waste Acceptance Product Specifications (WAPS). The WAPS sets the maximum post cooldown temperature of the waste-form glass at 400 degrees C. This criterion must be satisfied for the ambient conditions and heat generation rates expected for the waste-forms. As part of the work described in task plan, WSRC-RP-93-1177, Rev. 0, a computer model was used to calculate the maximum glass temperatures in free standing wasteforms for a variety of ambient temperatures and heat generation rates

  15. Construction of an automated table standing

    Science.gov (United States)

    Neira, R. E.; Barbero, M. D.; Di Giulio, E. A.; Folco, J. F.; Jiménez, G. F.

    2011-12-01

    In this paper, the construction of an upright stretcher designed for patients in rehabilitation. The standing back to patients' expectations of therapeutic improvement, allowing correct all the troubles of a passive long. It has been shown that this table favors not only physically but also has a psychological reach beyond the scope of physical therapy and strongly affects the recovery. At the same time, the use of an upright stretcher greatly decreases the biomechanical disorders of hospital staff in the process of recovery. Thus the problem of rehabilitation of trafficking in a comprehensive way which not only focuses on the patient's undivided attention but also includes medical and auxiliary personnel.

  16. SSRL photocathode RF gun test stand

    International Nuclear Information System (INIS)

    Hernandez, M.; Baltay, M.; Boyce, A.

    1995-01-01

    A photocathode RF gun test stand designed for the production and study of high brightness electron beams will be constructed at SSRL. The beam will be generated from a laser driven third generation photocathode RF gun being developed in collaboration with BNL, LBL, and UCLA. The 3-5 [MeV] beam from the gun will be accelerated using a SLAC three meter S-band accelerator section, in order to achieve the desired low emittance beam, emittance compensation with solenoidal focusing will be employed

  17. Droplets bouncing on a standing wave field

    Science.gov (United States)

    Pucci, Giuseppe; Tambasco, Lucas; Harris, Daniel; Bush, John

    2017-11-01

    A liquid bath subject to a vertical vibration becomes unstable to standing surface waves at a critical vibrational acceleration known as the Faraday threshold. We examine the behavior of a millimetric droplet bouncing on the surface of a quasi-one-dimensional fluid channel above the Faraday threshold. We identify a sequence of bifurcations that occurs as the vibrational acceleration is increased progressively, ultimately leading to the erratic, diffusive motion of the droplet along the length of the channel. A simple theoretical model is presented. This work was supported by the US National Science Foundation through Grants CMMI-1333242 and DMS-1614043.

  18. Numerical Investigation of Three-dimensional Instability of Standing Waves

    Science.gov (United States)

    Zhu, Qiang; Liu, Yuming; Yue, Dick K. P.

    2002-11-01

    We study the three-dimensional instability of finite-amplitude standing waves under the influence of gravity using the transition matrix method. For accurate calculation of the transition matrices, we apply an efficient high-order spectral element method for nonlinear wave dynamics in complex domain. We consider two types of standing waves: (a) plane standing waves; and (b) standing waves in a circular tank. For the former, in addition to the confirmation of the side-band-like instability, we find a new three-dimensional instability for arbitrary base standing waves. The dominant component of the unstable disturbance is an oblique standing wave, with an arbitrary angle relative to the base flow, whose frequency is approximately equal to that of the base standing wave. Based on direct simulations, we confirm such a three-dimensional instability and show the occurrence of the Fermi-Pasta-Ulam recurrence phenomenon during nonlinear evolution. For the latter, we find that beyond a threshold wave steepness, the standing wave with frequency Ω becomes unstable to a small three-dimensional disturbance, which contains two dominant standing-wave components with frequencies ω1 and ω_2, provided that 2Ω ω1 + ω_2. The threshold wave steepness is found to decrease/increase as the radial/azimuthal wavenumber of the base standing wave increases. We show that the instability of standing waves in rectangular and circular tanks is caused by third-order quartet resonances between base flow and disturbance.

  19. Science stand-up at CERN

    CERN Multimedia

    Stephanie McClellan

    2013-01-01

    Supported by host Helen Keen from BBC4’s "It is Rocket Science", six amateur performers from CERN (Sam Gregson, Alex Brown, Benjamin Frisch, Claire Lee, Hugo Day and Clara Nellist) were joined on stage by geek-pop sensation Jonny Berliner and comedians Pierre Novellie and Lieven Scheire for a night of science stand-up comedy.   Host Helen Keen starts off the comedy event. (Image: Piotr Traczyk). Like the genesis of most great things, the LHComedy event began as an idea. Sam Gregson, a PhD student at CERN, had been a regular at the Cambridge Bright Club. This public engagement event promotes scientists’ research through stand-up comedy. Sam thought, “If people came to watch Bright Club at Cambridge and enjoyed the research, why can’t we do it at the biggest scientific experiment in the world?” Sam’s idea gained momentum after being introduced to FameLab participants at CERN. Similar to Bright Club, FameLab is a com...

  20. Engineering design of vertical test stand cryostat

    International Nuclear Information System (INIS)

    Suhane, S.K.; Sharma, N.K.; Raghavendra, S.; Joshi, S.C.; Das, S.; Kush, P.K.; Sahni, V.C.; Gupta, P.D.; Sylvester, C.; Rabehl, R.; Ozelis, J.

    2011-01-01

    Under Indian Institutions and Fermilab collaboration, Raja Ramanna Centre for Advanced Technology and Fermi National Accelerator Laboratory are jointly developing 2K Vertical Test Stand (VTS) cryostats for testing SCRF cavities at 2K. The VTS cryostat has been designed for a large testing aperture of 86.36 cm for testing of 325 MHz Spoke resonators, 650 MHz and 1.3 GHz multi-cell SCRF cavities for Fermilab's Project-X. Units will be installed at Fermilab and RRCAT and used to test cavities for Project-X. A VTS cryostat comprises of liquid helium (LHe) vessel with internal magnetic shield, top insert plate equipped with cavity support stand and radiation shield, liquid nitrogen (LN 2 ) shield and vacuum vessel with external magnetic shield. The engineering design and analysis of VTS cryostat has been carried out using ASME B and PV Code and Finite Element Analysis. Design of internal and external magnetic shields was performed to limit the magnetic field inside LHe vessel at the cavity surface 2 shield has been performed to check the effectiveness of LN 2 cooling and for compliance with ASME piping code allowable stresses.

  1. Standing Stability in Knee Osteoarthritis Patients

    Directory of Open Access Journals (Sweden)

    M.T. Karimi

    2016-09-01

    Full Text Available Aims: Being prevalent in the more than 40 years old persons, the knee osteoarthritis is one of the main factors in the function system failure mainly affecting their life. There is a type of instability in the persons with knee osteoarthritis, which is an increase in the domain and frequency of body pressure center. The aim of the present study was to compare the standing stability parameters in persons with knee osteoarthritis and healthy persons. Instrument & Methods: In this case-control, 15 patients with knee osteoarthritis referred to the physiotherapy clinic of the rehabilitation center and Al-Zahra hospital were studied in the muscle-skeletal research center of Isfahan University of Medical Sciences in 2015. The subjects were selected via stratified sampling method. As control group, 15 healthy persons were also studied in Isfahan. Total path length and the domain and frequency of pressure center in different directions were measured to assess the stability. Data was analyzed by SPSS 19 software using descriptive statistics and paired T test. Findings: There were increases in the mean movement domain and the frequency of pressure center in the anterior-posterior and the internal-external directions, as well as in the total path proceeded by the pressure center in the internal-external direction, in the persons with knee osteoarthritis than the healthy persons (p0.05. Conclusion: Standing stability and balance in persons with knee osteoarthritis decreases compared to healthy persons.

  2. Rehabilitation of Understocked Loblolly-Shortleaf Pine Stands - I. Recently Cutover Natural Stands

    Science.gov (United States)

    James B. Baker; Michael G. Shelton

    1998-01-01

    A 1988 USDA Forest Service report indicated that 22% (40 million ac) of the commercial timberland in the South was understocked (less than 60% stocking) with desirable tree species for timber production (USDA Forest Service 1988). The understocked stands are usually the result of past har-vesting practices, natural catastrophes, or regeneration fail-ures. Understocked...

  3. Transmission components of solar radiation in pine stands in relation to climatic and stand variables

    Science.gov (United States)

    Robert A. Muller

    1971-01-01

    In a new approach, transmission was studied by relating to stand biomass the ratio of incoming solar radiation beneath tree crowns to that within the atmosphere. Several assumptions were used to estimate analytically the various ways in which solar radiation penetrates through crowns of three pine species in northern California. Sunflecks accounted for much of the...

  4. Stand characteristics of 65-year-old planted and naturally regenerated stands near Sequim, Washington.

    Science.gov (United States)

    Richard E. Miller; Harry W. Anderson

    1995-01-01

    Tree numbers, height, and volume were determined in six 63- to 66-year-old plantations of coast Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco var. menziesii) in northwest Washington. These stands resulted from the first extensive plantings of this species in the Pacific Northwest. Data from 0.25-acre plots in these...

  5. Blood pressure associates with standing balance in elderly outpatients.

    Directory of Open Access Journals (Sweden)

    Jantsje H Pasma

    Full Text Available OBJECTIVES: Assessment of the association of blood pressure measurements in supine and standing position after a postural change, as a proxy for blood pressure regulation, with standing balance in a clinically relevant cohort of elderly, is of special interest as blood pressure may be important to identify patients at risk of having impaired standing balance in routine geriatric assessment. MATERIALS AND METHODS: In a cross-sectional cohort study, 197 community-dwelling elderly referred to a geriatric outpatient clinic of a middle-sized teaching hospital were included. Blood pressure was measured intermittently (n = 197 and continuously (subsample, n = 58 before and after a controlled postural change from supine to standing position. The ability to maintain standing balance was assessed during ten seconds of side-by-side, semi-tandem and tandem stance, with both eyes open and eyes closed. Self-reported impaired standing balance and history of falls were recorded by questionnaires. Logistic regression analyses were used to examine the association between blood pressure and 1 the ability to maintain standing balance; 2 self-reported impaired standing balance; and 3 history of falls, adjusted for age and sex. RESULTS: Blood pressure decrease after postural change, measured continuously, was associated with reduced ability to maintain standing balance in semi-tandem stance with eyes closed and with increased self-reported impaired standing balance and falls. Presence of orthostatic hypotension was associated with reduced ability to maintain standing balance in semi-tandem stance with eyes closed for both intermittent and continuous measurements and with increased self-reported impaired standing balance for continuous measurements. CONCLUSION: Continuous blood pressure measurements are of additional value to identify patients at risk of having impaired standing balance and may therefore be useful in routine geriatric care.

  6. The stand prototype of minimum power NRE reactor

    International Nuclear Information System (INIS)

    Belogurov, A.I.; Grigorenko, L.N.; Mamontov, Yu.I.; Rachuk, V.S.; Stukalov, A.I.; Konyukhov, G.V.

    1995-01-01

    For ensuring of full-scale development of nuclear rocket engine (NRE) reactor was created stand prototype (reactor IRGIT?) The main differences of its are as follows: 1) Fasteners of technologies channels contents fuel assemblies in bottom are worked out the split. It is provides possibility a distance channels change without disassembly of reactor stand prototype from stand; 2) Cooling of the vessels, the moderator, the reflector and the barrel actuate is carried out by hydrogen; 3) The lower bottom modified for organization the hydrogen efflux in the form a reactor jet; 4) Radiation defence is introduced as part of stand prototype for ensuring of serviceability of stand accessories and tests routine service; 5) Each technology channels is provided of critical nozzle; 6) Control, regulation and defence of reactor has being carried out on stand system

  7. Stand model for upland forests of Southern Arkansas

    Energy Technology Data Exchange (ETDEWEB)

    Mielke, D.L.; Shugart, H.H.; West, D.C.

    1978-06-01

    A forest stand growth and composition simulator (FORAR) was developed by modifying a stand growth model by Shugart and West (1977). FORAR is a functional stand model which used ecological parameters to relate individual tree growth to environment rather than using Markov probability matrices or differential equations to determine single tree or species replacement rates. FORAR simulated tree growth and species composition of upland forests of Union County, Ark., by considering 33 tree species on a /sup 1///sub 12/ ha circular plot.

  8. Tilt table standing for reducing spasticity after spinal cord injury.

    Science.gov (United States)

    Bohannon, R W

    1993-10-01

    A patient with a T12 spinal cord injury and intractable extensor spasms of the lower extremities participated in tilt table standing trial on 5 nonconsecutive days to determine if the intervention would affect his spasticity and spasms. Each day's standing trial was followed by an immediate reduction in lower extremity spasticity (measured using the modified Ashworth scale and pendulum testing). Standing was also accompanied by a reduction in spasms that lasted until the following morning. The reduction of spasms was particularly advantageous to the performance of car transfers. Tilt table standing merits further examination as a physical treatment of spasms that accompany central nervous system lesions.

  9. Flexible integration of free-standing nanowires into silicon photonics.

    Science.gov (United States)

    Chen, Bigeng; Wu, Hao; Xin, Chenguang; Dai, Daoxin; Tong, Limin

    2017-06-14

    Silicon photonics has been developed successfully with a top-down fabrication technique to enable large-scale photonic integrated circuits with high reproducibility, but is limited intrinsically by the material capability for active or nonlinear applications. On the other hand, free-standing nanowires synthesized via a bottom-up growth present great material diversity and structural uniformity, but precisely assembling free-standing nanowires for on-demand photonic functionality remains a great challenge. Here we report hybrid integration of free-standing nanowires into silicon photonics with high flexibility by coupling free-standing nanowires onto target silicon waveguides that are simultaneously used for precise positioning. Coupling efficiency between a free-standing nanowire and a silicon waveguide is up to ~97% in the telecommunication band. A hybrid nonlinear-free-standing nanowires-silicon waveguides Mach-Zehnder interferometer and a racetrack resonator for significantly enhanced optical modulation are experimentally demonstrated, as well as hybrid active-free-standing nanowires-silicon waveguides circuits for light generation. These results suggest an alternative approach to flexible multifunctional on-chip nanophotonic devices.Precisely assembling free-standing nanowires for on-demand photonic functionality remains a challenge. Here, Chen et al. integrate free-standing nanowires into silicon waveguides and show all-optical modulation and light generation on silicon photonic chips.

  10. Relationship of Tree Stand Heterogeneity and Forest Naturalness

    Directory of Open Access Journals (Sweden)

    BARTHA, Dénes

    2006-01-01

    Full Text Available The aim of our study was to investigate if compositional (tree species richness andstructural (vertical structure, age-structure, patterns of canopy closure heterogeneity of the canopylayer is related to individual naturalness criteria and to overall forest naturalness at the stand scale. Thenaturalness values of the assessed criteria (tree species composition, tree stand structure, speciescomposition and structure of shrub layer and forest floor vegetation, dead wood, effects of game, sitecharacteristics showed similar behaviour when groups of stands with different heterogeneity werecompared, regardless of the studied aspect of canopy heterogeneity. The greatest difference was foundfor criteria describing the canopy layer. Composition and structure of canopy layer, dead wood andtotal naturalness of the stand differed significantly among the stand groups showing consistentlyhigher values from homogeneous to the most heterogeneous group. Naturalness of the compositionand structure of the shrub layer is slightly but significantly higher in stands with heterogeneous canopylayer. Regarding other criteria, significant differences were found only between the homogeneous andthe most heterogeneous groups, while groups with intermediate level of heterogeneity did not differsignificantly from one extreme. However, the criterion describing effects of game got lowernaturalness values in more heterogeneous stands. Naturalness of site characteristics did not differsignificantly among the groups except for when stands were grouped based on pattern of canopyclosure. From the practical viewpoint it is shown that purposeful forestry operations affecting thecanopy layer cause changes in compositional and structural characteristics of other layers as well as inoverall stand scale forest naturalness.

  11. The experiences of mastery of stand-by energy demand; Les experiences de MDE stand by

    Energy Technology Data Exchange (ETDEWEB)

    Schilken, P

    2001-07-01

    In the residential sector of the OECD countries, the electricity losses of domestic appliances in stand-by position represent 1.5% of the total electricity consumption. This study belongs to the SAVE project (pilot campaign of municipal utilities for an improved rational use of energy). Its aim is to observe the policies and experiments implemented by municipalities and municipal energy companies for the abatement of the electricity consumptions of stand-by origin. A working group consisting of the German Stadtwerke and some international partners have debated the possible actions and documents for an efficient information of the public. This document presents the brochures and local actions of this program. (J.S.)

  12. Validation of the VitaBit Sit–Stand Tracker: Detecting Sitting, Standing, and Activity Patterns

    Directory of Open Access Journals (Sweden)

    Nathalie M. Berninger

    2018-03-01

    Full Text Available Sedentary behavior (SB has detrimental consequences and cannot be compensated for through moderate-to-vigorous physical activity (PA. In order to understand and mitigate SB, tools for measuring and monitoring SB are essential. While current direct-to-customer wearables focus on PA, the VitaBit validated in this study was developed to focus on SB. It was tested in a laboratory and in a free-living condition, comparing it to direct observation and to a current best-practice device, the ActiGraph, on a minute-by-minute basis. In the laboratory, the VitaBit yielded specificity and negative predictive rates (NPR of above 91.2% for sitting and standing, while sensitivity and precision ranged from 74.6% to 85.7%. For walking, all performance values exceeded 97.3%. In the free-living condition, the device revealed performance of over 72.6% for sitting with the ActiGraph as criterion. While sensitivity and precision for standing and walking ranged from 48.2% to 68.7%, specificity and NPR exceeded 83.9%. According to the laboratory findings, high performance for sitting, standing, and walking makes the VitaBit eligible for SB monitoring. As the results are not transferrable to daily life activities, a direct observation study in a free-living setting is recommended.

  13. Using a stand-level model to predict light absorption in stands with vertically and horizontally heterogeneous canopies

    Directory of Open Access Journals (Sweden)

    David I Forrester

    2014-09-01

    Full Text Available Background Forest ecosystem functioning is strongly influenced by the absorption of photosynthetically active radiation (APAR, and therefore, accurate predictions of APAR are critical for many process-based forest growth models. The Lambert-Beer law can be applied to estimate APAR for simple homogeneous canopies composed of one layer, one species, and no canopy gaps. However, the vertical and horizontal structure of forest canopies is rarely homogeneous. Detailed tree-level models can account for this heterogeneity but these often have high input and computational demands and work on finer temporal and spatial resolutions than required by stand-level growth models. The aim of this study was to test a stand-level light absorption model that can estimate APAR by individual species in mixed-species and multi-layered stands with any degree of canopy openness including open-grown trees to closed canopies. Methods The stand-level model was compared with a detailed tree-level model that has already been tested in mixed-species stands using empirical data. Both models were parameterised for five different forests, including a wide range of species compositions, species proportions, stand densities, crown architectures and canopy structures. Results The stand-level model performed well in all stands except in the stand where extinction coefficients were unusually variable and it appears unlikely that APAR could be predicted in such stands using (tree- or stand-level models that do not allow individuals of a given species to have different extinction coefficients, leaf-area density or analogous parameters. Conclusion This model is parameterised with species-specific information about extinction coefficients and mean crown length, diameter, height and leaf area. It could be used to examine light dynamics in complex canopies and in stand-level growth models.

  14. Consumo de suplementos por alunos de academias de ginástica em São Paulo Supplement consumption among fitness center users in São Paulo, Brazil

    Directory of Open Access Journals (Sweden)

    Raquel Franzini Pereira

    2003-09-01

    Full Text Available O aumento do número de academias de ginástica na cidade de São Paulo, em conjunto com o aumento da oferta de diferentes suplementos no mercado, despertou interesse para o estudo do consumo de suplementos entre seus alunos. O uso de suplementos pelo público em geral não é bem quantificado e pouca informação sobre este assunto está publicada na literatura. O seu aparecimento no mercado tem sido mais rápido do que a elaboração de regulamentações e a realização de pesquisas científicas que comprovem seus efeitos na saúde dos consumidores e determinem a segurança de seu uso a longo prazo. Em uma amostra de 309 freqüentadores de sete academias de ginástica de São Paulo em 1999, 74 (23,9% consumiam algum tipo de suplemento, dos quais 77,0% eram do sexo masculino e 23,0% do sexo feminino. Os suplementos mais consumidos foram aminoácidos ou outros concentrados protéicos (38,9% e o consumo maior foi o diário (90,3%. A correlação entre gasto com suplemento e renda individual foi de 27,5% (p = 0,0483; n=52, sendo o gasto com suplementos maior entre homens do que entre mulheres; a correlação com renda familiar foi de 36,1% (p = 0,0137; n = 46 e com Índice de Massa Corporal foi de 17,1% (p = 0,1564; n = 70. Conclui-se que o uso de suplementos é significante no grupo analisado, ficando clara a necessidade de novos estudos sobre o consumo desses produtos e seus efeitos, enfocando aspectos de educação nutricional do consumidor de suplementos para aumentar o nível de informação sobre os mesmos e garantir segurança na sua utilização.The increase in the number of fitness centers in the city of São Paulo, together with the increase in the offering of different supplements, has raised interest in the study of the consumption of supplements among fitness center users. The consumption of supplements by the general public has not been well quantified yet, and little information has been published about this subject. The arrival of

  15. Harvesting budworm-damaged stands for fuel

    Energy Technology Data Exchange (ETDEWEB)

    Henley, S.G. (York, Sunbury, Charlotte Wood Products Marketing Board, (Canada))

    1985-01-01

    This project was initiated to demonstrate the economics and logistics of harvesting budworm-damaged stands for use as fuel. Dead spruce and balsam fir were to be harvested from small private woodlots in southwestern New Brunswick, using an integrated, full-tree harvesting system to produce wood chip fuel and other forest products. The overall objectives of the study are listed. The harvesting equipment and the selection of sites are discussed. The most efficient methods of finding candidate woodlots was found to be by advertising and word of mouth. Contact was made with 85 woodlot owners, and 45 woodlots were visited and evaluated for their suitability. A further 150 management plans were screened and rejected for various reasons. Only 2 woodlots were initially recognized as potential sites; however, after showing some interest, the owners decided not to participate. The reasons for the rejection of the various woodlots are listed. The fact that a number of owners were against clearcutting, and, in some cases, against any cutting, and that others showed no interest in the study, is attributed to the high percentage of white-collar workers owning woodlots. Other strategies for harvesting dead or scrap wood are suggested. 1 ref., 1 tab.

  16. Key processes from tree to stand level

    International Nuclear Information System (INIS)

    Hinckley, T.; Ford, D.; Segura, G.; Sprugel, D.

    1991-01-01

    Changes in six factors have been identified as having potential major future impacts on the productivity and survival of forest trees and stands. These factors are atmospheric carbon dioxide concentration, tropospheric ozone concentration, mean annual air temperature and precipitation, extremes in temperature and precipitation, and levels of ultraviolet radiation. Except for precipitation, all of these factors are expected to increase with climatic change. However, the likelihood of their increase or change ranges from the given to the unknown. The way in which one or more of these factors might individually or in combination affect the productivity and survival of trees is discussed, and particularly sensitive physiological processes are identified. For example, increases in winter temperature and a doubling of CO 2 will result in early budburst in many species and therefore increase the risk of frost damage. In other species or locations, warm winters may mean insufficient chilling hours and the requirements for release from bud dormancy may not be met. The interaction of these processes with current species distribution, genotype selection, and management alternatives is reviewed. 52 refs., 1 fig., 1 tab

  17. Developing a mobile stand alone photovoltaic generator

    International Nuclear Information System (INIS)

    Soler-Bientz, R.; Ricalde-Cab, L.O.; Solis-Rodriguez, L.E.

    2006-01-01

    This paper describes a recent work developed to create a mobile stand alone photovoltaic generator that can be easily relocated in remote areas to evaluate the feasibility of photovoltaic energy applications. A set of sensors were installed to monitor the electric current and voltage of the energy generated, the energy stored and the energy used by the loads that may be connected to the system. Other parameters like solar radiations (both on the horizontal and on the photovoltaic generation planes) and temperatures (of both the environment and the photovoltaic module) were monitored. This was done while considering the important role of temperature in the photovoltaic module performance. Finally, a measurement and communication hardware was installed to interface the system developed with a conventional computer. In this way, the performance of the overall system in real rural conditions could be evaluated efficiently. Visual software that reads, visualizes and saves the data generated by the system was also developed by means of the LabVIEW programming environment

  18. Visual evoked responses during standing and walking

    Directory of Open Access Journals (Sweden)

    Klaus Gramann

    2010-10-01

    Full Text Available Human cognition has been shaped both by our body structure and by its complex interactionswith its environment. Our cognition is thus inextricably linked to our own and others’ motorbehavior. To model brain activity associated with natural cognition, we propose recording theconcurrent brain dynamics and body movements of human subjects performing normal actions.Here we tested the feasibility of such a mobile brain/body (MoBI imaging approach byrecording high-density electroencephalographic (EEG activity and body movements of subjectsstanding or walking on a treadmill while performing a visual oddball response task. Independentcomponent analysis (ICA of the EEG data revealed visual event-related potentials (ERPs thatduring standing, slow walking, and fast walking did not differ across movement conditions,demonstrating the viability of recording brain activity accompanying cognitive processes duringwhole body movement. Non-invasive and relatively low-cost MoBI studies of normal, motivatedactions might improve understanding of interactions between brain and body dynamics leadingto more complete biological models of cognition.

  19. Brookhaven National Laboratory electron beam test stand

    International Nuclear Information System (INIS)

    Pikin, A.; Alessi, J.; Beebe, E.; Kponou, A.; Prelec, K.; Snydstrup, L.

    1998-01-01

    The main purpose of the electron beam test stand (EBTS) project at the Brookhaven National Laboratory is to build a versatile device to develop technologies that are relevant for a high intensity electron beam ion source (EBIS) and to study the physics of ion confinement in a trap. The EBTS will have all the main attributes of EBIS: a 1-m-long, 5 T superconducting solenoid, electron gun, drift tube structure, electron collector, vacuum system, ion injection system, appropriate control, and instrumentation. Therefore it can be considered a short prototype of an EBIS for a relativistic heavy ion collider. The drift tube structure will be mounted in a vacuum tube inside a open-quotes warmclose quotes bore of a superconducting solenoid, it will be at room temperature, and its design will employ ultrahigh vacuum technology to reach the 10 -10 Torr level. The first gun to be tested will be a 10 A electron gun with high emission density and magnetic compression of the electron beam. copyright 1998 American Institute of Physics

  20. RAMSES stands guard over the accelerator chain

    CERN Multimedia

    CERN Bulletin

    2010-01-01

    RAMSES, the system that is used to monitor radiation at the LHC, CNGS, CTF3 and n-TOF facilities, will soon be installed at strategic points in the accelerator chain, replacing the older monitoring system ARCON. The replacement programme has already begun.   RAMSES (which stands for “Radiation Monitoring System for the Environment and Safety”) is designed to protect workers, the general public and the environment, both on the Organization’s site and in the surrounding areas. It is currently operational on all the LHC sites and at CTF3, CNGS and n-TOF, while the remaining sites are still equipped with the ARCON (Area CONtroller) system. Daniel Perrin, head of the Instrumentation and Logistics Section of the HSE Unit's Radiation Protection Group, explains: “ARCON was designed for the old LEP accelerator and dates back to the early 1980s, while RAMSES is a much more recent design intended specifically for the LHC. With 389 detectors distributed across 124 mea...

  1. F-15B ACTIVE test stand

    Science.gov (United States)

    1995-01-01

    This November 13, 1995, photograph of the underside of the F-15 Advanced Controls Technology for Integrated Vehicles (ACTIVE) at NASA's Dryden Flight Research Center, Edwards, California, shows the thrust stand being used for ground testing of a new thrust-vectoring concept. The twin-engine F-15 research aircraft is equipped with new Pratt & Whitney nozzles that can turn up to 20 degrees in any direction. They give the aircraft thrust control in the pitch (up and down) and yaw (left and right) directions. This will reduce drag and increase fuel economy or range as compared with conventional aerodynamic controls, which increase the retarding forces (drag) acting upon the aircraft. Ground testing during the first two weeks of November 1995 went well, and flight tests began in March 1996. These tests could result in significant performance increases for military and commercial aircraft. The research program is the product of a collaborative effort by NASA, the Air Force's Wright Laboratory, Pratt & Whitney, and McDonnell Douglas Aerospace.

  2. Release of dissolved 85Kr by standing

    International Nuclear Information System (INIS)

    Ootsuka, Norikatsu; Yamamoto, Tadatoshi; Tsukui, Kohei

    1986-01-01

    The experiments on the release of dissolved 85 Kr by standing at room temperature were carried out to examine the influence of liquid level in a sampler and properties of solvent on the release efficiency. Six kinds of organic solvents as well as water were taken as solvents. The half-life period in case of the decrease in concentration of the dissolved 85 Kr which was used as an index of release efficiency, was proportional to the liquid level in the sampler and was inversely proportional to the diffusion coefficient of Kr gas in solvent. For organic solvents belonging to homologous series, the half-life period became longer with increasing the carbon number of solvent molecule. From the relationship between the half-life period and the carbon number, the release efficiency in the dissolved 85 Kr can be predicted for any commonly used solvent as a practical application. This method was found to be an effective means of removing the dissolved 85 Kr of low level though it takes rather long time. (author)

  3. Heavy thinning of ponderosa pine stands: An Arizona case study

    Science.gov (United States)

    Peter F. Ffolliott; Jr. Baker; Gerald J. Gottfried

    2000-01-01

    Growth and structural changes in a mosaic of even-aged ponderosa pine (Pinus ponderosa) stands were studied for 25 years to determine the long-term impacts of a heavy thinning treatment to a basal-area level of 25 ft2/acre. Basal area and volume growth of these stands has increased since thinning and likely will continue to...

  4. Flooding effects on stand development in cypress-tupelo

    Science.gov (United States)

    Richard F. Keim; Thomas J. Dean; Jim L. Chambers

    2013-01-01

    The effects of inundation on growth of cypress (Taxodium spp.) and tupelo (Nyssa spp.) trees have been extensively researched, but conclusions are often complicated by attendant effects on stand development. Flooding affects development of cypress-tupelo stands by limiting seedling germination and survival, truncating species...

  5. Simple Excitation of Standing Waves in Rubber Bands and Membranes

    Science.gov (United States)

    Cortel, Adolf

    2004-04-01

    Many methods to excite standing waves in strings, plates, membranes, rods, tubes, and soap bubbles have been described. Usually a loudspeaker or a vibrating reed is driven by the amplified output of an audio oscillator. A novel and simple method consists of using a tuning fork or a singing rod to excite transversal standing waves in stretched rubber membranes sprinkled with fine sand.

  6. The health of loblolly pine stands at Fort Benning, GA

    Science.gov (United States)

    Soung-Ryoul Ryu; G. Geoff Wang; Joan L. Walker

    2013-01-01

    Approximately two-thirds of the red-cockaded woodpecker (Picoides borealis) (RCW) groups at Fort Benning, GA, depend on loblolly pine (Pinus taeda) stands for nesting or foraging. However, loblolly pine stands are suspected to decline. Forest managers want to replace loblolly pine with longleaf pine (P. palustris...

  7. 39 CFR 122.2 - Stand-alone special services.

    Science.gov (United States)

    2010-07-01

    ... 39 Postal Service 1 2010-07-01 2010-07-01 false Stand-alone special services. 122.2 Section 122.2 Postal Service UNITED STATES POSTAL SERVICE POST OFFICE SERVICES [DOMESTIC MAIL] SERVICE STANDARDS FOR MARKET-DOMINANT SPECIAL SERVICES PRODUCTS § 122.2 Stand-alone special services. (a) The service standard...

  8. A whole stand basal area projection model for Appalachian hardwoods

    Science.gov (United States)

    John R. Brooks; Lichun Jiang; Matthew Perkowski; Benktesh Sharma

    2008-01-01

    Two whole-stand basal area projection models were developed for Appalachian hardwood stands. The proposed equations are an algebraic difference projection form based on existing basal area and the change in age, trees per acre, and/or dominant height. Average equation error was less than 10 square feet per acre and residuals exhibited no irregular trends.

  9. Stand, Harvest, and Equipment Interactions in Simulated Harvesting Prescriptions

    Science.gov (United States)

    Jingxin Wang; W. Dale Greene; Bryce J. Stokes

    1998-01-01

    We evaluated potential interactions of stand type, harvesting method, and equipment in an experiment using interactive simulation. We examined three felling methods (chain saw, feller-buncher, harvester) and two extraction methods (grapple skidder and forwarder) performing clearcuts, sheltenvood cuts, and single-tree selection cuts in both an uneven-aged natural stand...

  10. Natural disturbance and stand development principles for ecological forestry

    Science.gov (United States)

    Jerry F. Franklin; Robert J. Mitchell; Brian J. Palik

    2007-01-01

    Foresters use natural disturbances and stand development processes as models for silvicultural practices in broad conceptual ways. Incorporating an understanding of natural disturbance and stand development processes more fully into silvicultural practice is the basis for an ecological forestry approach. Such an approach must include 1) understanding the importance of...

  11. The importance of spatial accuracy in characterizing stand types ...

    African Journals Online (AJOL)

    This study assessed the potential use of Landsat 7 ETM+ (15 and 30 m spatial resolutions) images to estimate forest stand attributes such as development stages, crown closure and stand types. The study evaluates the performance of spatial and image classification accuracies between Landsat images (15 and 30 m ...

  12. XML/TEI Stand-off Markup. One step beyond.

    NARCIS (Netherlands)

    Spadini, E.; Turska, Magdalena

    2018-01-01

    Stand-off markup is widely considered as a possible solution for overcoming the limitation of inline XML markup, primarily dealing with multiple overlapping hierarchies. Considering previous contributions on the subject and implementations of stand-off markup, we propose a new TEI-based model for

  13. Harvesting systems for western stand health improvement cuttings

    Science.gov (United States)

    Bruce R. Hartsough; Bryce J. Stokes; Joseph F. McNeel; William F. Watson

    1995-01-01

    A significant percentage of the forested area in the western United States is comprised of stands that have been altered over time by human activities, especially fire suppression, and are now being damaged by droughts, insect attacks, and wildfires. These stands should be returned to a condition where "biotic and abiotic influences do not threaten resource...

  14. "Growing trees backwards": Description of a stand reconstruction model

    Science.gov (United States)

    Jonathan D. Bakker; Andrew J. Sanchez Meador; Peter Z. Fule; David W. Huffman; Margaret M. Moore

    2008-01-01

    We describe an individual-tree model that uses contemporary measurements to "grow trees backward" and reconstruct past tree diameters and stand structure in ponderosa pine dominated stands of the Southwest. Model inputs are contemporary structural measurements of all snags, logs, stumps, and living trees, and radial growth measurements, if available. Key...

  15. Direct measurement of the intrinsic ankle stiffness during standing

    NARCIS (Netherlands)

    Vlutters, Mark; Vlutters, M.; Boonstra, Tjitske; Schouten, Alfred Christiaan; van der Kooij, Herman

    2015-01-01

    Ankle stiffness contributes to standing balance, counteracting the destabilizing effect of gravity. The ankle stiffness together with the compliance between the foot and the support surface make up the ankle-foot stiffness, which is relevant to quiet standing. The contribution of the intrinsic

  16. Information Entropy Measures for Stand Structural Diversity:Joint Entropy

    Institute of Scientific and Technical Information of China (English)

    Lei Xiangdong; Lu Yuanchang

    2004-01-01

    Structural diversity is the key attribute of a stand. A set of biodiversity measures in ecology was introduced in forest management for describing stand structure, of which Shannon information entropy (Shannon index) has been the most widely used measure of species diversity. It is generally thought that tree size diversity could serve as a good proxy for height diversity. However, tree size diversity and height diversity for stand structure is not completely consistent. Stand diameter cannot reflect height information completely. Either tree size diversity or height diversity is one-dimensional information entropy measure. This paper discussed the method of multiple-dimensional information entropy measure with the concept of joint entropy. It is suggested that joint entropy is a good measure for describing overall stand structural diversity.

  17. The role of forest stand structure as biodiversity indicator

    DEFF Research Database (Denmark)

    Gao, Tian; Hedblom, Marcus; Emilsson, Tobias

    2014-01-01

    be achieved if indicators are derived from existing data. In this study, a model for classifying forest stand structures was developed and tested as an indicator of overall plant species diversity at stand level. The model combines four stand structure parameters: canopy coverage, age of canopy trees, tree...... species composition and canopy stratification. Using data from the National Inventory of Landscapes in Sweden and General Linear Mixed Model, plant species diversity (Shannon diversity index, SHDI) and composition (Sørensen-Dice index, SDI) were tested between 26 different stand structure types and nine...... soil classes. The results showed that mature stands with a stratified canopy had the highest plant species diversity across the soil classes, particularly if they comprised mixed coniferous and broadleaved species with a semi-open canopy. In contrast, young (...

  18. Effects of stand and inter-specific stocking on maximizing standing tree carbon stocks in the eastern United States

    Science.gov (United States)

    Christopher W. Woodall; Anthony W. D' Amato; John B. Bradford; Andrew O. Finley

    2011-01-01

    There is expanding interest in management strategies that maximize forest carbon (C) storage to mitigate increased atmospheric carbon dioxide. The tremendous tree species diversity and range of stand stocking found across the eastern United States presents a challenge for determining optimal combinations for the maximization of standing tree C storage. Using a...

  19. Converting partially-stocked aspen stands to fully-stocked stands in the Lake States: an economic analysis.

    Science.gov (United States)

    Jeffrey T. Olson; Allen L. Lundgren

    1978-01-01

    The 1968 Wisconsin Forest Survey showed large areas of aspen type that are not considered fully stocked. The economic feasibility of converting partially-stocked stands to full stocking is examined, and a rule presented for determining when a partially-stocked stand should be harvested to maximize its present value.

  20. Desk-based workers' perspectives on using sit-stand workstations: a qualitative analysis of the Stand@Work study

    NARCIS (Netherlands)

    Chau, J.Y.; Daley, M.; Srinivasan, A.; Dunn, S.; Bauman, A.E.; van der Ploeg, H.P.

    2014-01-01

    Background: Prolonged sitting time has been identified as a health risk factor. Sit-stand workstations allow desk workers to alternate between sitting and standing throughout the working day, but not much is known about their acceptability and feasibility. Hence, the aim of this study was to

  1. Multi-muscle electrical stimulation and stand training: Effects on standing.

    Science.gov (United States)

    Momeni, Kamyar; Ramanujam, Arvind; Garbarini, Erica L; Forrest, Gail F

    2018-02-15

    To examine the biomechanical and neuromuscular effects of a longitudinal multi-muscle electrical stimulation (submaximal intensities) training of the lower limbs combined with/without activity-based stand training, on the recovery of stability and function for one individual with spinal cord injury (SCI). Single-subject, longitudinal study. Neuroplasticity laboratory. A 34-year-old male, with sensory- and motor-complete SCI (C5/C6). Two consecutive interventions: 61 hours of supine, lower-limb ES (ES-alone) and 51 hours of ES combined with stand training using an overhead body-weight support system (ST + ES). Clinical measures, trunk stability, and muscle activity were assessed and compared across time points. Trunk Stability Limit (TSL) determined improvements in trunk independence. Functional clinical values increased after both interventions, with further increases post ST + ES. Post ES-alone, trunk stability was maintained at 81% body-weight (BW) loading before failure; post ST + ES, BW loading increased to 95%. TSL values decreased post ST + ES (TSL A/P =54.0 kg.cm, TSL M/L =14.5 kg.cm), compared to ES-alone (TSL A/P =8.5 kg.cm, TSL M/L =3.9 kg.cm). Trunk muscle activity decreased post ST + ES training, compared to ES-alone. Neuromuscular and postural trunk control dramatically improved following the multi-muscle ES of the lower limbs with stand training. Multi-muscle ES training paradigm of the lower limb, using traditional parameters, may contribute to the functional recovery of the trunk.

  2. Financial Village Standing in Indonesian Financial System

    Directory of Open Access Journals (Sweden)

    Herry Purnomo

    2015-12-01

    Full Text Available Financial resources of the village that are sourced from a country or a Regional Finance Financial based Law Number 6 Year 2014 of The Village is the mandate of the law that must be allocated to the village. The interconnectedness of the financial position of the village in the financial system of the country or Region concerned the Financial administrative and territorial relations, and there is no setting directly regarding the finances of the village as part of the financial system of the country or the financial area. In respect of the elements of the crime of corruption deeds against financial irregularities of the village there are still disagreements on the interpretation of the law in trapping the perpetrators of corruption on the village chief that implies not satisfy the principle of legality and legal certainty in the ruling of the matter of financial irregularities. In fact, many of the village chief or Councilor caught the criminal offence of corruption over the use of financial irregularities. This research analyzes How the financial position of the village in the financial system of the country or region, as well as whether the financial resources of the village is derived from the state budget or region budget managed in village budget belongs to the category of village finances and whether tort against the financial management of the village can be categorized as a criminal act corruption. How To Cite: Purnomo, H. (2015. Financial Village Standing in Indonesian Financial System. Rechtsidee, 2(2, 121-140. doi:http://dx.doi.org/10.21070/jihr.v2i2.81

  3. The experiences of MDE stand-by; Les experiences de MDE stand-by

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    The control of the electric power demand (MDE) is a worrying subject for many countries. The consumption of the electrical equipment in stand-by, is evaluated at 20 TWh/year for the ternary and residential sectors in Germany and 5,3 in France. Taking into account the SAVE project (Pilot campaign of municipal utilities for an improved rational use of energy), this study aims to observe the policies and the experiences of local governments in terms of energy consumption reduction. (A.L.B.)

  4. Isotope enrichment effect of gaseous mixtures in standing sound vibration

    International Nuclear Information System (INIS)

    Knesebeck, R.L.

    1984-01-01

    When standing acoustic waves are excited in a tube containing a mixture of two gases, a partial zonal fractioning of the components arises as consequence of mass transport by diffusion, driven by the thermal and pressure gradients which are associeted with the standing waves. This effect is present in each zone corresponding to a quarter wavelength, with the heavier component becoming enriched at the nodes fo the standing waves and deplected at the crests. The magnitude of the enrichment in one of the components of a binary gas mixture is given by Δω=ap 2 /lambda [b + (1-bω)] 2 . Where ω is the mass concentration of the component in the mixture, a and b are parameters which are related to molecular proprieties of the gases, p is the relative pressure amplitude of the standing wave and lambda is its wavelength. For a natural mixture of uranium hexafluorate, with 0.715% of the uranium isotope 340 an enrichment of about 2 x 10 -6 % in the concentration of this isotope is theorecticaly attainable per stage consisting of a quarter wavelenght, when a standing acoustical wave of relative pressure amplitude of 0,2 and wavelenght of 20 cm is used. Since standing acoustical waves are easely excited in gas columns, an isotope enrichment plant made of a cascade of tubes in which standing waves are excited, is presumably feasible with relatively low investment and operation costs. (Author) [pt

  5. StandsSIM-MD: a Management Driven forest SIMulator

    Energy Technology Data Exchange (ETDEWEB)

    Barreiro, S.; Rua, J.; Tomé, M.

    2016-07-01

    Aim of the study. The existing stand level forest simulators available in Portugal were not developed with the aim of including up-to-date model versions and were limited in terms of accounting for forest management. The simulators’ platform, sIMfLOR was recently created to implement different growth models with a common philosophy. The objective was developing one easily-updatable, user-friendly, forest management and climate change sensitive simulator capable of projecting growth for the main tree species in Portugal. Area of the study: Portugal. Material and methods: The new simulator was programmed in a modular form consisting of several modules. The growth module integrates different forest growth and yield models (empirical and process-based) for the main wood production tree species in Portugal (eucalypt, umbrella and maritime pines); whereas the management module drives the growth projections along the planning horizon according to a range of forest management approaches and climate (at present only available for eucalypt). Main results: The main result is the StandsSIM-MD Management Driven simulator that overcomes the limitations of the existing stand level simulators. It is a step forward when compared to the models currently available in the sIMfLOR platform covering more tree species, stand structures and stand compositions. It is focused on end-users and it is based on similar concepts regarding the generation of required inputs and generated outputs. Research highlights: Forest Management Driven simulations approach. Multiple Prescriptions-Per-Stand functionality. StandsSIM-MD can be used to support landowners decisions on stand forest management. StandsSIM-MD simulations at regional level can be combined with optimization routines. (Author)

  6. Stand for testing the electrical race car engine

    Science.gov (United States)

    Baier, M.; Franiasz, J.; Mierzwa, P.; Wylenzek, D.

    2015-11-01

    An engine test stand created especially for research of electrical race car is described in the paper. The car is an aim of Silesian Greenpower project whose participants build and test electrical vehicles to take part in international races in Great Britain. The engine test stand is used to test and measure the characteristics of vehicles and their engines. It has been designed particularly to test the electric cars engineered by students of Silesian Greenpower project. The article contains a description how the test stand works and shows its versatility in many areas. The paper presents both construction of the test stand, control system and sample results of conducted research. The engine test stand was designed and modified using PLM Siemens NX 8.5. The construction of the test stand is highly modular, which means it can be used both for testing the vehicle itself or for tests without the vehicle. The test stand has its own wheel, motor, powertrain and braking system with second engine. Such solution enables verifying various concepts without changing the construction of the vehicle. The control system and measurement system are realized by enabling National Instruments product myRIO (RIO - Reconfigurable Input/Output). This controller in combination with powerful LabVIEW environment performs as an advanced tool to control torque and speed simultaneously. It is crucial as far as the test stand is equipped in two motors - the one being tested and the braking one. The feedback loop is realized by an optical encoder cooperating with the rotor mounted on the wheel. The results of tests are shown live on the screen both as a chart and as single values. After performing several tests there is a report generated. The engine test stand is widely used during process of the Silesian Greenpower vehicle design. Its versatility enables powertrain testing, wheels and tires tests, thermal analysis and more.

  7. Sit to stand activity during stroke rehabilitation.

    Science.gov (United States)

    Kerr, Andy; Dawson, Jesse; Robertson, Chris; Rowe, Philip; Quinn, Terence J

    2017-12-01

    Objectives The sit to stand (STS) movement is key to independence and commonly affected by stroke. Repetitive practice is likely to improve STS ability during rehabilitation, however current practice levels are unknown. The objective of this study was simply to count the number of STS movements performed during the rehabilitation period of stroke patients using a physical activity monitor (PAM) and test whether being observed altered outcome. Methods Participants were medically stable patients referred for rehabilitation following stroke. Participants were randomly allocated to either wear or not wear the PAM for 14 days. STS ability and general mobility were recorded before and after. Results Sixty-one patients was recruited; aged 68.4 ± 13.15 years, weight 77.12 ± 22.73 Kg, Height 1.67 ± 0.1 m, within 9 ± 9 days of their stroke and an NIHSS score of 6.4 ± 3.3. The monitored group (n = 38) performed 25.00 ± 17.24 daily STS movements. Those requiring assistance achieved 14.29 ± 16.10 per day while those independent in the movement achieved 34.10 ± 12.44. There was an overall improvement in mobility (p = 0.002) but not STS performance (p = 0.053) neither outcome was affected by group allocation (p = 0.158). Cognition and mobility at baseline explained around 50% of daily STS variability. Discussion Low levels of STS activity were recorded during the rehabilitation period of stroke patient. The mean daily STS activity was lower than reports for frail older people receiving rehabilitation, and substantially below levels recorded by community living older adults. STS repetitions may represent general physical activity and these low levels support previous reports of sedentary behavior during rehabilitation.

  8. Electromagnetic calibration system for sub-micronewton torsional thrust stand

    Science.gov (United States)

    Lam, J. K.; Koay, S. C.; Cheah, K. H.

    2017-12-01

    It is critical for a micropropulsion system to be evaluated. Thrust stands are widely recognised as the instrument to complete such tasks. This paper presents the development of an alternative electromagnetic calibration technique for thrust stands. Utilising the commercially made voice coils and permanent magnets, the proposed system is able to generate repeatable and also consistent steady-state calibration forces at over four orders of magnitude (30 - 23000 μN). The system is then used to calibrate a custom-designed torsional thrust stand, where its inherent ability in ease of setup is well demonstrated.

  9. A Cryogenic Test Stand for Large Superconducting Solenoid Magnets

    Energy Technology Data Exchange (ETDEWEB)

    Rabehl, R. [Fermilab; Carcagno, R. [Fermilab; Nogiec, J. [Fermilab; Orris, D. [Fermilab; Soyars, W. [Fermilab; Sylvester, C. [Fermilab

    2013-01-01

    A new test stand for testing large superconducting solenoid magnets at the Fermilab Central Helium Liquifier (CHL) has been designed, and operated. This test stand has been used to test a coupling coil for the Muon Ionization Cooling Experiment (MICE), and future uses include solenoids for the Fermilab mu2e experiment. This paper describes the test stand design and operation including controlled cool-down and warm-up. Overviews of the process controls system and the quench management system are also included.

  10. Prevalência do uso e conhecimento de esteroides anabolizantes androgênicos por estudantes e professores de educação física que atuam em academias de ginástica

    Directory of Open Access Journals (Sweden)

    Odilon Salim Costa Abrahin

    2013-02-01

    Full Text Available INTRODUÇÃO: Os esteroides anabólicos androgênicos (EAA são substâncias, quimicamente semelhantes à testosterona, utilizadas para o tratamento/controle de diversas doenças. Contudo, tais substâncias estão sendo empregadas de forma não terapêutica e indiscriminada com finalidades de melhora da performance esportiva e principalmente estética. OBJETIVO: analisar a prevalência do uso e o conhecimento de EAA por estudantes e professores de educação física que atuam em academias de ginástica de Belém, PA. Utilizou-se para a coleta de dados um questionário fechado e anônimo, aplicado a 117 pesquisados. A comparação da prevalência do uso e o grau de conhecimento dos pesquisados sobre EAA foi realizada através de estatística não paramétrica, prova de X² (Qui-quadrado, considerando o intervalo de confiança de 95% e p < 0,05. A média de idade dos participantes da pesquisa foi de 28,0 ± 6,3 anos e a prevalência do uso de EAA foi de 31,6% do total de sujeitos pesquisados. A prevalência maior foi entre os profissionais especialistas (39,3%, tendo como principal motivação para o uso de EAA a estética com 75,6%. Em relação ao conhecimento, verificou-se que as drogas classificadas como EAA foram: Durateston®, Deca-Durabolin®, oxandrolona/Winstrol®. Entretanto, estes profissionais confundiram-se ao apontar outras substâncias como sendo EAA, entre elas: hormônio do crescimento e óleos localizados. Entre os efeitos colaterais, os mais citados foram: acne, engrossamento da voz e agressividade; contudo, efeitos colaterais mais prejudiciais como câncer e aromatização foram menos assinalados. RESULTADOS: Demonstraram que a prevalência de uso de EAA foi significativa (p < 0,03 entre os estudantes e professores de educação física que atuam em academias de Belém, PA, revelando assim prováveis desconhecimentos destes sobre alguns dos efeitos colaterais, podendo implicar no uso indiscriminado destas drogas.

  11. Sexuality educators: taking a stand by participating in research

    African Journals Online (AJOL)

    Sexuality educators: taking a stand by participating in research ... and Sexually Transmitted Infections (STIs) (United Nations Educational, Scientific, .... assimilates new ideas which could assist in keeping up with what learners need from.

  12. Litterfall and Nutrient Returns in Isolated Stands of Terminalia ...

    African Journals Online (AJOL)

    ... Stands of Terminalia catappa Trees in the Rainforest Area of Southern Nigeria. ... the adjoining rainforests produced the highest litter in the dry season months. ... Seasonal variation, Southern Nigeria, Terminalia catappa, Tropical rainforest.

  13. Free standing graphene oxide film for hydrogen peroxide sensing

    Science.gov (United States)

    Ranjan, Pranay; Balakrishnan, Jayakumar; Thakur, Ajay D.

    2018-05-01

    We report hydrogen peroxide (H2O2)sensing using free standing graphene oxide thin films prepared using a cost effective scalable approach. Such sensors may find application in pharmaceutical and food processing industries.

  14. Isopropyl alcohol tank installed at A-3 Test Stand

    Science.gov (United States)

    2009-01-01

    An isopropyl alcohol (IPA) tank is lifted into place at the A-3 Test Stand being built at NASA's John C. Stennis Space Center. Fourteen IPA, water and liquid oxygen (LOX) tanks are being installed to support the chemical steam generators to be used on the A-3 Test Stand. The IPA and LOX tanks will provide fuel for the generators. The water will allow the generators to produce steam that will be used to reduce pressure inside the stand's test cell diffuser, enabling operators to simulate altitudes up to 100,000 feet. In that way, operators can perform the tests needed on rocket engines being built to carry humans back to the moon and possibly beyond. The A-3 Test Stand is set for completion and activation in 2011.

  15. Stand-alone induction generators for small water power schemes

    Energy Technology Data Exchange (ETDEWEB)

    Harvey, Adam [Intermediate Technology Development Group, Rugby (United Kingdom); Smith, Nigel [Smith Associates, Nottingham (United Kingdom)

    1996-04-01

    Conventional technology for isolated power generation is the synchronous generator. Using stand-alone induction generators has proved to have tremendous advantages in remote regions of developing countries, where electricity has significant social benefits. (author)

  16. Basic Stand Alone Medicare DME Line Items PUF

    Data.gov (United States)

    U.S. Department of Health & Human Services — This release contains the Basic Stand Alone (BSA) Durable Medical Equipment (DME) Line Items Public Use Files (PUF) with information from Medicare DME claims. The...

  17. Impact of timber production and transport costs on stand management

    Science.gov (United States)

    Chris B. LeDoux; Chris B. LeDoux

    1988-01-01

    Evaluates the impact of cable logging technology, transportation network standards, and transport vehicles on stand management. Managers can use results to understand the impact of timber production costs on eastern hardwood management.

  18. Validation of Standing Wave Liner Impedance Measurement Method, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Hersh Acoustical Engineering, Inc. proposes to establish the feasibility and practicality of using the Standing Wave Method (SWM) to measure the impedance of...

  19. Basic Stand Alone Skilled Nursing Facility Beneficiary PUF

    Data.gov (United States)

    U.S. Department of Health & Human Services — This release contains the Basic Stand Alone (BSA) Skilled Nursing Facility (SNF) Beneficiary Public Use Files (PUF) with information from Medicare SNF claims. The...

  20. Structural attributes of stand overstory and light under the canopy

    Directory of Open Access Journals (Sweden)

    Alice Angelini

    2015-02-01

    Full Text Available  This paper reviews the literature relating to the relationship between light availability in the understory and the main qualitative and quantitative attributes of stand overstory usually considered in forest management and planning (species composition, density, tree sizes, etc. as well as their changes as consequences of harvesting. The paper is divided in two sections: the first one reviews studies which investigated the influence of species composition on understory light conditions; the second part examines research on the relationships among stand parameters determined from dendrometric field data and the radiation on understory layer. The objective was to highlight which are the most significant stand traits and management features to build more practical models for predicting light regimes in any forest stand and, in more general terms, to support forest managers in planning and designing silvicultural treatments that retain structure in different way in order to meet different objectives.

  1. Robot-supported assessment of balance in standing and walking

    NARCIS (Netherlands)

    Shirota, Camila; van Asseldonk, Edwin; Matjacic, Zlatko; Vallery, H.; Barralon, Pierre; Maggioni, Serena; Buurke, Jaap H.; Veneman, Jan F.

    2017-01-01

    Clinically useful and efficient assessment of balance during standing and walking is especially challenging in patients with neurological disorders. However, rehabilitation robots could facilitate assessment procedures and improve their clinical value. We present a short overview of balance

  2. Stationary Density Variation Produced by a Standing Plasma Wave

    DEFF Research Database (Denmark)

    Michelsen, Poul; Pécseli, Hans; Juul Rasmussen, Jens

    1977-01-01

    Measurements are presented of a stationary density modulation produced by a standing electron plasma wave. The experimental results are well explained by taking into account the ponderomotive forces on the electrons exerted by the high frequency field.......Measurements are presented of a stationary density modulation produced by a standing electron plasma wave. The experimental results are well explained by taking into account the ponderomotive forces on the electrons exerted by the high frequency field....

  3. Destroyed virgin longleaf pine stand lives-on digitally

    Science.gov (United States)

    John C. Gilbert; S. Kush; Rebecca J. Barlow

    2015-01-01

    The Flomaton Natural Area (FNA) once stood as one of the few remnant fragments of virgin, old-growth longleaf pine stands (Pinus palustris Mill.) in the Southeast. This 80-acre stand contained trees over 200 years old. A restoration effort began in 1994 to remove off-site trees and to reintroduce fire to the site after over 40 years of fire suppression. A geographic...

  4. Do Pine Trees in Aspen Stands Increase Bird Diversity

    OpenAIRE

    Rumble, Mark A; Mills, Todd R; Dystra, Brian L; Flake, Lester D

    2001-01-01

    In the Black Hills of South Dakota, quaking aspen (Populus tremuloides) is being replaced by conifers through fire suppression and successional processes. Al- though the Black Hills National forest is removing conifers (primarily ponderosa pine [Pinus ponderosa])toincreasetheaspencommunitiesinsomemixedstands,ForestPlan guidelines allow four conifers per hectare to remain to increase diversity in the remaining aspen stand. We compared bird species richness in pure ponderosa pine, mixed stands ...

  5. Long-standing temporomandibular joint dislocation: A rare experience

    Directory of Open Access Journals (Sweden)

    Kapil Malik

    2017-01-01

    Full Text Available Long-standing temporomandibular joint (TMJ dislocations persist for more than a month are most challenging to treat. The management of such condition varies widely, from closed reduction to complicated surgical procedures. The choice of an appropriate methodology is questionable. At present, there are no standard rules or conventions for the ideal strategy in different circumstances. This paper attempts to present the experience of managing two cases of long-standing TMJ dislocations.

  6. Normal distribution of standing balance for healthy Danish children

    DEFF Research Database (Denmark)

    Pedersen, Line Kjeldgaard; Ghasemi, Habib; Rahbek, Ole

    2013-01-01

    Title: Normal distribution of standing balance for healthy Danish children – Reproducibility of parameters of balance. Authors Line Kjeldgaard Pedersen Habib Ghasemi Ole Rahbek Bjarne Møller-Madsen 1800 characters incl. spaces Background Pedobarographic measurements are increasingly used in child......Title: Normal distribution of standing balance for healthy Danish children – Reproducibility of parameters of balance. Authors Line Kjeldgaard Pedersen Habib Ghasemi Ole Rahbek Bjarne Møller-Madsen 1800 characters incl. spaces Background Pedobarographic measurements are increasingly used...

  7. J-2 Engine ready to go into test stand

    Science.gov (United States)

    1965-01-01

    Two technicians watch carefully as cables prepare to lift a J-2 engine into a test stand. The J-2 powered the second stage and the third stage of the Saturn V moon rocket. The towering 363-foot Saturn V was a multi-stage, multi-engine launch vehicle standing taller than the Statue of Liberty. Altogether, the Saturn V engines produced as much power as 85 Hoover Dams.

  8. Standing Wave Field Distribution in Graded-Index Antireflection Coatings

    Directory of Open Access Journals (Sweden)

    Hongxiang Deng

    2018-01-01

    Full Text Available Standing wave field distributions in three classic types of graded-index antireflection coatings are studied. These graded-index antireflection coatings are designed at wavelengths from 200 nm to 1200 nm, which is the working wavelength range of high energy laser system for inertial-fusion research. The standing wave field distributions in these coatings are obtained by the numerical calculation of electromagnetic wave equation. We find that standing wave field distributions in these three graded-index anti-reflection coatings are quite different. For the coating with linear index distribution, intensity of standing wave field decreases periodically from surface to substrate with narrow oscillation range and the period is proportional to the incident wavelength. For the coating with exponential index distribution, intensity of standing wave field decreases periodically from surface to substrate with large oscillation range and the period is also proportional to the incident wavelength. Finally, for the coating with polynomial index, intensity of standing wave field is quickly falling down from surface to substrate without an obvious oscillation. We find that the intensity of standing wave field in the interface between coating and substrate for linear index, exponential index and polynomial index are about 0.7, 0.9 and 0.7, respectively. Our results indicate that the distributions of standing wave field in linear index coating and polynomial index coating are better than that in exponential index coating for the application in high energy laser system. Moreover, we find that the transmittance of linear index coating and polynomial index coating are also better than exponential index coating at the designed wavelength range. Present simulation results are useful for the design and application of graded-index antireflection coating in high energy laser system.

  9. Mixing Effects in Norway Spruce—European Beech Stands Are Modulated by Site Quality, Stand Age and Moisture Availability

    Directory of Open Access Journals (Sweden)

    Léa Houpert

    2018-02-01

    Full Text Available Although mixing tree species is considered an efficient risk-reduction strategy in the face of climate change, the conditions where mixtures are more productive than monocultures are under ongoing debate. Generalizations have been difficult because of the variety of methods used and due to contradictory findings regarding the effects of the species investigated, mixing proportions, and many site and stand conditions. Using data from 960 plots of the Swiss National Forest Inventory data, we assessed whether Picea abies (L. Karst–Fagus sylvatica L. mixed stands are more productive than pure stands, and whether the mixing effect depends on site- or stand-characteristics. The species proportions were estimated using species proportion by area, which depends on the maximum stand basal area of an unmanaged stand (BAmax. Four different alternatives were used to estimate BAmax and to investigate the effect of these differing alternatives on the estimated mixture effect. On average, the mixture had a negative effect on the growth of Picea abies. However, this effect decreased as moisture availability increased. Fagus sylvatica grew better in mixtures and this effect increased with site quality. A significant interaction between species proportions and quadratic mean diameter, a proxy for stand age, was found for both species: the older the stand, the better the growth of Fagus sylvatica and the lower the growth of Picea abies. Overyielding was predicted for 80% of the investigated sites. The alternative to estimate BAmax weakly modulated the estimated mixture effect, but it did not affect the way mixing effects changed with site characteristics.

  10. StandsSIM-MD: a Management Driven forest SIMulator

    Directory of Open Access Journals (Sweden)

    Susana Barreiro

    2016-07-01

    Full Text Available Aim of the study: The existing stand level forest simulators available in Portugal were not developed with the aim of including up-to-date model versions and were limited in terms of accounting for forest management. The simulators’ platform, sIMfLOR was recently created to implement different growth models with a common philosophy. The objective was developing one easily-updatable, user-friendly, forest management and climate change sensitive simulator capable of projecting growth for the main tree species in Portugal. Area of the study: Portugal. Material and methods: The new simulator was programmed in a modular form consisting of several modules. The growth module integrates different forest growth and yield models (empirical and process-based for the main wood production tree species in Portugal (eucalypt, umbrella and maritime pines; whereas the management module drives the growth projections along the planning horizon according to a range of forest management approaches and climate (at present only available for eucalypt. Main results: The main result is the StandsSIM-MD Management Driven simulator that overcomes the limitations of the existing stand level simulators. It is a step forward when compared to the models currently available in the sIMfLOR platform covering more tree species, stand structures and stand compositions. It is focused on end-users and it is based on similar concepts regarding the generation of required inputs and generated outputs. Research highlights: -          Forest Management Driven simulations approach -          Multiple Prescriptions-Per-Stand functionality -          StandsSIM-MD can be used to support landowners decisions on stand forest management -          StandsSIM-MD simulations at regional level can be combined with optimization routines Keywords: Forest simulator, Forest Management Approaches; StandsSIM-MD; forest management.

  11. Acoustic radiation force on a sphere in standing and quasi-standing zero-order Bessel beam tweezers

    International Nuclear Information System (INIS)

    Mitri, F.G.

    2008-01-01

    Starting from the exact acoustic scattering from a sphere immersed in an ideal fluid and centered along the propagation axis of a standing or quasi-standing zero-order Bessel beam, explicit partial-wave representations for the radiation force are derived. A standing or a quasi-standing acoustic field is the result of propagating two equal or unequal amplitude zero-order Bessel beams, respectively, along the same axis but in opposite sense. The Bessel beam is characterized by the half-cone angle β of its plane wave components, such that β = 0 represents a plane wave. It is assumed here that the half-cone angle β for each of the counter-propagating acoustic Bessel beams is equal. Fluid, elastic and viscoelastic spheres immersed in water are treated as examples. Results indicate the capability of manipulating spherical targets based on their mechanical and acoustical properties. This condition provides an impetus for further designing acoustic tweezers operating with standing or quasi-standing Bessel acoustic waves. Potential applications include particle manipulation in micro-fluidic lab-on-chips as well as in reduced gravity environments

  12. 2015 Space Radiation Standing Review Panel

    Science.gov (United States)

    Steinberg, Susan

    2015-01-01

    The 2015 Space Radiation Standing Review Panel (from here on referred to as the SRP) met for a site visit in Houston, TX on December 8 - 9, 2015. The SRP met with representatives from the Space Radiation Element and members of the Human Research Program (HRP) to review the updated research plan for the Risk of Radiation Carcinogenesis Cancer Risk. The SRP also reviewed the newly revised Evidence Reports for the Risk of Acute Radiation Syndromes Due to Solar Particle Events (SPEs) (Acute Risk), the Risk of Acute (In-flight) and Late Central Nervous System Effects from Radiation Exposure (CNS Risk), and the Risk of Cardiovascular Disease and Other Degenerative Tissue Effects from Radiation (Degen Risk), as well as a status update on these Risks. The SRP would like to commend Dr. Simonsen, Dr. Huff, Dr. Nelson, and Dr. Patel for their detailed presentations. The Space Radiation Element did a great job presenting a very large volume of material. The SRP considers it to be a strong program that is well-organized, well-coordinated and generates valuable data. The SRP commended the tissue sharing protocols, working groups, systems biology analysis, and standardization of models. In several of the discussed areas the SRP suggested improvements of the research plans in the future. These include the following: It is important that the team has expanded efforts examining immunology and inflammation as important components of the space radiation biological response. This is an overarching and important focus that is likely to apply to all aspects of the program including acute, CVD, CNS, cancer and others. Given that the area of immunology/inflammation is highly complex (and especially so as it relates to radiation), it warrants the expansion of investigators expertise in immunology and inflammation to work with the individual research projects and also the NASA Specialized Center of Research (NSCORs). Historical data on radiation injury to be entered into the Watson

  13. Stand diameter distribution modelling and prediction based on Richards function.

    Directory of Open Access Journals (Sweden)

    Ai-guo Duan

    Full Text Available The objective of this study was to introduce application of the Richards equation on modelling and prediction of stand diameter distribution. The long-term repeated measurement data sets, consisted of 309 diameter frequency distributions from Chinese fir (Cunninghamia lanceolata plantations in the southern China, were used. Also, 150 stands were used as fitting data, the other 159 stands were used for testing. Nonlinear regression method (NRM or maximum likelihood estimates method (MLEM were applied to estimate the parameters of models, and the parameter prediction method (PPM and parameter recovery method (PRM were used to predict the diameter distributions of unknown stands. Four main conclusions were obtained: (1 R distribution presented a more accurate simulation than three-parametric Weibull function; (2 the parameters p, q and r of R distribution proved to be its scale, location and shape parameters, and have a deep relationship with stand characteristics, which means the parameters of R distribution have good theoretical interpretation; (3 the ordinate of inflection point of R distribution has significant relativity with its skewness and kurtosis, and the fitted main distribution range for the cumulative diameter distribution of Chinese fir plantations was 0.4∼0.6; (4 the goodness-of-fit test showed diameter distributions of unknown stands can be well estimated by applying R distribution based on PRM or the combination of PPM and PRM under the condition that only quadratic mean DBH or plus stand age are known, and the non-rejection rates were near 80%, which are higher than the 72.33% non-rejection rate of three-parametric Weibull function based on the combination of PPM and PRM.

  14. Ginástica como atividade motivacional

    Directory of Open Access Journals (Sweden)

    Jaqueline Batista de Oliveira Costa

    2009-12-01

    Full Text Available This study analyzed whether the activities of occupational gymnastic promote the satisfaction of the worker, generate motivational stimuli for carrying out their tasks, induce sentiments of welfare and good interpersonal relationships at work and within the family. The group sharing this research was composed of a population of 24 women and 20 men aged 20 to 51 years, who practice occupational gymnastics on the premises of a factory in the city of Presidente Prudente, five times a week, from Mondays to Fridays, during the morning and afternoon. The instrument of data collection was a questionnaire containing nine questions that aimed to identify the level of satisfaction, motivation and welfare of workers in the context of work and family. The inquiry proved that the occupational gymnastics is capable to improve the satisfaction of the worker with his task, since it causes happier and reduce body pains. The subjects declared that the practice of occupational gymnastics raises the will to share the domestic tasks, improve the disposition to the family leisure and causes a substantial change in the mood. The study showed, ultimately, that the workers became more eager with their bodies and with their personal health conditions.

  15. Standing wave acoustic levitation on an annular plate

    Science.gov (United States)

    Kandemir, Mehmet Hakan; Çalışkan, Mehmet

    2016-11-01

    In standing wave acoustic levitation technique, a standing wave is formed between a source and a reflector. Particles can be attracted towards pressure nodes in standing waves owing to a spring action through which particles can be suspended in air. This operation can be performed on continuous structures as well as in several numbers of axes. In this study an annular acoustic levitation arrangement is introduced. Design features of the arrangement are discussed in detail. Bending modes of the annular plate, known as the most efficient sound generation mechanism in such structures, are focused on. Several types of bending modes of the plate are simulated and evaluated by computer simulations. Waveguides are designed to amplify waves coming from sources of excitation, that are, transducers. With the right positioning of the reflector plate, standing waves are formed in the space between the annular vibrating plate and the reflector plate. Radiation forces are also predicted. It is demonstrated that small particles can be suspended in air at pressure nodes of the standing wave corresponding to a particular bending mode.

  16. Relating P-band AIRSAR backscatter to forest stand parameters

    Science.gov (United States)

    Wang, Yong; Melack, John M.; Davis, Frank W.; Kasischke, Eric S.; Christensen, Norman L., Jr.

    1993-01-01

    As part of research on forest ecosystems, the Jet Propulsion Laboratory (JPL) and collaborating research teams have conducted multi-season airborne synthetic aperture radar (AIRSAR) experiments in three forest ecosystems including temperate pine forest (Duke, Forest, North Carolina), boreal forest (Bonanza Creek Experimental Forest, Alaska), and northern mixed hardwood-conifer forest (Michigan Biological Station, Michigan). The major research goals were to improve understanding of the relationships between radar backscatter and phenological variables (e.g. stand density, tree size, etc.), to improve radar backscatter models of tree canopy properties, and to develop a radar-based scheme for monitoring forest phenological changes. In September 1989, AIRSAR backscatter data were acquired over the Duke Forest. As the aboveground biomass of the loblolly pine forest stands at Duke Forest increased, the SAR backscatter at C-, L-, and P-bands increased and saturated at different biomass levels for the C-band, L-band, and P-band data. We only use the P-band backscatter data and ground measurements here to study the relationships between the backscatter and stand density, the backscatter and mean trunk dbh (diameter at breast height) of trees in the stands, and the backscatter and stand basal area.

  17. A Measurement System of Electric Signals on Standing Trees

    Directory of Open Access Journals (Sweden)

    Hao TIAN

    2014-01-01

    Full Text Available The standing tree electric signal (STES, defined as the electric potential difference between standing trees and the surrounding soil, can be utilized to reflect the biological nature of the trees. This signal should be measured precisely because it can also be collected and used as the electric power energy. In this paper, the automatic measurement system of standing tree biological electric signal based on MSP430 MCU. First of all, the basic structure of the presented system is introduced and it includes three modules: amplification module of the standing tree electric signal, the acquisition and processing of the signal module and the serial communication module. Then, the performances of the built system are respectively validated by the Poplar, Planetree, and Platanus in Beijing Forestry University. The result indicated that the relative error of this system is less than 2 %. The presented system can be considered as the foundation of the subsequent study on the mechanism of the biological electric signal and the application of the biological electric energy on standing trees.

  18. [Soil quality assessment of forest stand in different plantation esosystems].

    Science.gov (United States)

    Huang, Yu; Wang, Silong; Feng, Zongwei; Gao, Hong; Wang, Qingkui; Hu, Yalin; Yan, Shaokui

    2004-12-01

    After a clear-cutting of the first generation Cunninghamia lanceolata plantation in 1982, three plantation ecosystems, pure Michelia macclurei stand (PMS), pure Chinese-fir stand (PCS) and their mixed stand, were established in spring 1983, and their effects on soil characteristics were evaluated by measuring some soil physical, chemical, microbiological and biochemical parameters. After 20 years' plantation, all test indices showed differences among different forest management models. Both PMS and MCM had a favorable effect on soil fertility maintenance. Soil quality assessment showed that some soil functions, e.g., water availability, nutrient availability, root suitability and soil quality index were all in a moderate level under the mixed and pure PMS stands, whereas in a relatively lower level under successive PCS stand. The results also showed that there existed close correlations between soil total organic C (TOC), cation exchange capacity (CEC), microbial biomass-C (Cmic) and other soil physical, chemical and biological indices. Therefore, TOC, CEC and Cmic could be used as the indicators in assessing soil quality in this study area. In addition, there were also positive correlations between soil microbial biomass-C and TOC, soil microbial biomass-N and total N, and soil microbial biomass-P and total P in the present study.

  19. The role of stand history in assessing forest impacts

    Science.gov (United States)

    Dale, V.H.; Doyle, T.W.

    1987-01-01

    Air pollution, harvesting practices, and natural disturbances can affect the growth of trees and forest development. To make predictions about anthropogenic impacts on forests, we need to understand how these factors affect tree growth. In this study the effect of disturbance history on tree growth and stand structure was examined by using a computer model of forest development. The model was run under the climatic conditions of east Tennessee, USA, and the results compared to stand structure and tree growth data from a yellow poplar-white oak forest. Basal area growth and forest biomass were more accurately projected when rough approximations of the thinning and fire history typical of the measured plots were included in the simulation model. Stand history can influence tree growth rates and forest structure and should be included in any attempt to assess forest impacts.

  20. Standing phase angle reduction for power system restoration

    Energy Technology Data Exchange (ETDEWEB)

    Hazarika, D. [Assam Engineering College (India). Electrical Engineering Dept.; Sinha, A.K. [IIT Khargpur (India). Electrical Engineering Dept.

    1998-01-01

    The paper describes a methodology for the reduction of standing phase angle (SPA) difference between two buses of a power system, which is essential before interconnecting a line between two buses. This problem is encountered normally during restoration operations of a power system. For this purpose, the standing phase angle difference between two specific buses is represented in terms of sensitivity factors associated with the change in real power injections at the buses. To arrive at the desired standing phase angle difference between two buses, the modified contribution at generation/load buses have been evaluated based on 'higher the sensitivity higher the participation' logic. This methodology acts as a direct help to reduce excessive SPA difference between two buses to an acceptable limit, which otherwise requires regulation of various generation levels on a trial and error basis. (author)

  1. Management of black Locust (Robinia pseudoacacia L.) stands in Hungary

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Black locust (Robinia pseudoacacia L.) was the first forest tree species to be imported from North America to Europe at the beginning of the 17th century. It is the most important fast-growing stand-forming tree species in Hungary . Black locust plantations can be successfully established in response to arange of economic and ecological opportunities. Plantation survival and productivity are maximized by matching the species' growth characteristics with silvicultura l options and land management needs. In the paper the sequence of forest tending operations in black locust stands is proposed, based on results of long-term st and structure and forest yield trials. Implementing good silvicultural plans and models will lead to profitable black locust stands and greater acceptance of the species by land managers. Black locust would also beavery useful species for energy productions as the related research results have been shown in the paper .

  2. Análise comparativa do equilíbrio unipodal de atletas de ginástica rítmica Comparative analysis of one-foot balance in rhythmic gymnastics athletes

    Directory of Open Access Journals (Sweden)

    Leonardo Shigaki

    2013-04-01

    Full Text Available INTRODUÇÃO: A ginástica rítmica (GR requer alto nível de qualidade física; assim, o bom desempenho é dependente da força e resistência muscular, coordenação motora e equilíbrio postural. OBJETIVO: Desenvolver uma análise comparativa do equilíbrio unipodal de atletas de GR. MÉTODOS: Foram avaliadas dez atletas de GR, do sexo feminino, por meio de uma plataforma de força em apoio unipodal e testes funcionais de equilíbrio (Side Hop Test e Figure of Eight Hop Teste. Para a plataforma, os parâmetros do Centro de Pressão (COP nas direções anteroposterior e mediolateral foram utilizados para análise, enquanto para os testes funcionais, o tempo-segundos de performance. RESULTADOS: Diferença significativa (p = 0,01 foi encontrada entre os membros inferiores no parâmetro de frequência média na direção mediolateral, no qual o membro inferior não dominante apresentou maior estabilidade postural do que o dominante. Para os testes funcionais não houve diferença significativa entre os membros. CONCLUSÃO: A diferença encontrada no controle do equilíbrio na direção mediolateral pode estar relacionada às diferenças nas ações musculares da região do quadril, na qual durante a prática do esporte para estabilização, manutenção do tronco e execução de manobras com os membros inferiores estão presentes. Estes resultados indicam a necessidade de um programa de reequilíbrio e estabilização pélvica para as atletas analisadas no intuito de preservar a simetria muscular dos membros para o bom desempenho esportivo.INTRODUCTION: Rhythmic gymnastics requires a high level of physical quality; therefore, good performance depends on muscular strength and endurance, motor coordination and postural balance. OBJECTIVE: To develop a comparative analysis of postural balance in rhythmic gymnasts. METHODS: 10 female rhythmic gymnasts were evaluated by a force platform on one foot and balance functional tests (Side Hop Test and

  3. Stand tending and root rot in Norway spruce stands - economical effects caused by root rot at different thinning regimes

    International Nuclear Information System (INIS)

    Johansson, Mats

    1997-01-01

    This report is divided into three parts: 1) a literature study describing the most common fungi causing rot in wood and descriptions of various strategies to reduce economic loss from root rot, 2) a check of a model describing the development of butt rot in pure Norway spruce plantations in southern Sweden, and 3) simulated economic effects of root rot in stands with various stand tending. The rot model was used to estimate future rot frequencies in the economic calculations. In order to avoid overestimations of rot frequencies, the calculations were also executed when assuming slower growth of rot than shown in the model. When analysing the economical effects of rot, the following three thinning programmes were used: Program 1: thinning at the ages of 30- and 45 years. Final felling at the ages 50-, 55-, 60-, 65-, and 70 years. Program 2: thinning at the ages of 40- and 60- years. Final felling at the ages 65 and 75 years. Program 3: thinning at the ages of 30-, 40-, 55-, and 70 years. Final felling at the ages 80 and 90 years. With an interest rate of 3%, programme 2 (final felling at the age of 65 years) had the highest value at present. This result was valid when presuming butt rot in the stand as well as when presuming no butt rot in the stand. There was a small difference between the value at present in programme 1 (final felling at the age of 60 years) and in programme 3 (final felling at the age of 80 years). When presuming butt rot in the stand, the value at present in programme 3 decreased somewhat more in comparison to the value at present in programme 1. Compared to no butt rot in the stand, the optimal final felling time appeared five to ten years earlier when assuming butt rot in the stand. Stand tending programme 1 and an interest rate of 3% were used. Interest rates 2 and 4% did not indicate shorter rotation. The calculated optimal time of final felling appeared at the same stand age whether assuming rot preset or not. The results in this study

  4. Stand quality management of a water oak plantation in Louisiana: preliminary results following thinning

    Science.gov (United States)

    James S. Meadows; Daniel A., Jr. Skojac

    2010-01-01

    Stand quality management is a new guiding principle in which thinning prescriptions are based on tree quality rather than on residual stand density. We recently initiated a series of hardwood thinning studies to determine the effects of four stand quality management thinning prescriptions on both stand-level and individual-tree-level growth, quality, and value: (1) no...

  5. Regeneration in defoliated and thinned hardwood stands of north-central West Virginia

    Science.gov (United States)

    R. M. Muzika; M. J. Twery

    1995-01-01

    Overstory species regeneration was examined in 1989, prior to gypsy moth defoliation and thinnings, on 16 stands in the West Virginia University Forest. Three stands were thinned and defoliated while five were thinned only and three were defoliated only. Five stands were neither thinned nor defoliated. Data were collected from these stands for three years subsequent to...

  6. Regenerating mixed oak stands in Pennsylvania: a quarter-century retrospective

    Science.gov (United States)

    P. J. Gould; K. C. Steiner; J. C. Finley; M. E. McDill

    2003-01-01

    The outcomes of regeneration treatments in 90 oak-dominated stands in Pennsylvania are examined 20 to 33 years after treatment. Approximately one-quarter of the stands failed to reach 50 percent stocking after at least 20 years, but most stands regenerated successfully. Red maple is the most frequently observed species in the regenerated stands, followed by oak species...

  7. The effect of a hybrid assistive limb® on sit-to-stand and standing patterns of stroke patients

    Science.gov (United States)

    Kasai, Rie; Takeda, Sunao

    2016-01-01

    [Purpose] The Hybrid Assistive Limb® (HAL®) robot suit is a powered exoskeleton that can assist a user’s lower limb movement. The purpose of this study was to assess the effectiveness of HAL® in stroke rehabilitation, focusing on the change of the sit-to-stand (STS) movement pattern and standing posture. [Subjects and Methods] Five stroke patients participated in this study. Single leg HAL® was attached to each subject’s paretic lower limb. The subjects performed STS three times both with and without HAL® use. A tri-axial accelerometer was used to assess the STS movement pattern. Forward-tilt angle (FTA) and the time required for STS were measured with and without HAL® use. Surface electromyography (EMG) of STS and standing were recorded to assess the vastus medialis muscle activities of the paretic limb. [Results] The average FTA without HAL® use was 35° and it improved to 43° with HAL® use. The time required for STS was longer for all subjects with HAL® use (without HAL® use: 3.42 s, with HAL® use: 5.11 s). The integrated EMGs of HAL® use compared to those without HAL®, were 83.6% and 66.3% for STS and standing, respectively. [Conclusion] HAL® may be effective in improving STS and standing patterns of stroke patients. PMID:27390416

  8. Standing Up for Learning: A Pilot Investigation on the Neurocognitive Benefits of Stand-Biased School Desks

    Directory of Open Access Journals (Sweden)

    Ranjana K. Mehta

    2015-12-01

    Full Text Available Standing desks have proven to be effective and viable solutions to combat sedentary behavior among children during the school day in studies around the world. However, little is known regarding the potential of such interventions on cognitive outcomes in children over time. The purpose of this pilot study was to determine the neurocognitive benefits, i.e., improvements in executive functioning and working memory, of stand-biased desks and explore any associated changes in frontal brain function. 34 freshman high school students were recruited for neurocognitive testing at two time points during the school year: (1 in the fall semester and (2 in the spring semester (after 27.57 (1.63 weeks of continued exposure. Executive function and working memory was evaluated using a computerized neurocognitive test battery, and brain activation patterns of the prefrontal cortex were obtained using functional near infrared spectroscopy. Continued utilization of the stand-biased desks was associated with significant improvements in executive function and working memory capabilities. Changes in corresponding brain activation patterns were also observed. These findings provide the first preliminary evidence on the neurocognitive benefits of standing desks, which to date have focused largely on energy expenditure. Findings obtained here can drive future research with larger samples and multiple schools, with comparison groups that may in turn implicate the importance of stand-biased desks, as simple environmental changes in classrooms, on enhancing children’s cognitive functioning that drive their cognitive development and impact educational outcomes.

  9. Bilateral Posterior Native Hip Dislocations after Fall from Standing

    Directory of Open Access Journals (Sweden)

    Jane Xiao

    2017-10-01

    Full Text Available We present a case of bilateral posterior native hip dislocations after a fall from standing. This exceedingly rare diagnosis is classically associated with younger patients whose bones are strong enough to dislocate rather than fracture in the setting of a high-momentum collision. We present an unusual case of an 88-year-old male with native hips who sustained a low-energy collision after falling from standing and was found to have bilateral posterior hip dislocations without associated pelvis or femur fractures.

  10. The 5D Standing Wave Braneworld with Real Scalar Field

    OpenAIRE

    Merab Gogberashvili; Pavle Midodashvili

    2013-01-01

    We introduce the new 5D braneworld with the real scalar field in the bulk. The model represents the brane which bounds collective oscillations of gravitational and scalar field standing waves. These waves are out of phase; that is, the energy of oscillations passes back and forth between the scalar and gravitational waves. When the amplitude of the standing waves is small, the brane width and the size of the horizon in extra space are of a same order of magnitude, and matter fields are locali...

  11. Wavelength variation of a standing wave along a vertical spring

    Science.gov (United States)

    Welsch, Dylan; Baker, Blane

    2018-03-01

    Hand-driven resonance can be observed readily in a number of mechanical systems including thin boards, rods, strings, and springs. In order to show such behavior in the vertical spring pictured in Fig. 1, a section of spring is grasped at a location about one meter from its free end and driven by small, circular motions of the hand. At driving frequencies of a few hertz, a dramatic standing wave is generated. One of the fascinating features of this particular standing wave is that its wavelength varies along the length of the spring.

  12. Electron-phonon coupling in quasi free-standing graphene

    DEFF Research Database (Denmark)

    Christian Johannsen, Jens; Ulstrup, Søren; Bianchi, Marco

    2013-01-01

    Quasi free-standing monolayer graphene can be produced by intercalating species like oxygen or hydrogen between epitaxial graphene and the substrate crystal. If the graphene is indeed decoupled from the substrate, one would expect the observation of a similar electronic dispersion and many......-body effects, irrespective of the substrate and the material used to achieve the decoupling. Here we investigate the electron-phonon coupling in two different types of quasi free-standing monolayer graphene: decoupled from SiC via hydrogen intercalation and decoupled from Ir via oxygen intercalation. Both...

  13. Data acquisition system for PLT Neutral Beam Test Stand

    International Nuclear Information System (INIS)

    Francis, J.E. Jr.; Hammons, C.E.

    1977-01-01

    The PLT Neutral Beam Test Stand at Oak Ridge National Laboratory was constructed to test and condition powerful neutral beam sources for the Princeton Large Torus experiment at Princeton Plasma Physics Laboratory. The data acquisition system for the test stand monitors the beam characteristics and power output to determine if the beam is operating at its design specifications. The high speed of the computer system is utilized to provide near-real-time analysis of experimental data. The analysis of the data is presented as numerical tabulation and graphic display

  14. A FEW CONSIDERATIONS ABOUT TRADE FAIR STANDS DESIGN

    Directory of Open Access Journals (Sweden)

    NEIDONI Nadina

    2017-05-01

    Full Text Available The paper presents some aspects related to the design of a trade fair stand, advertising a company specialized in the fabrication of corrugated fibre board packaging. The first section reviews shortly the main features of the industrial design. The second section deals with the structural conception of successful trade shows. Further, the importance of the package in the marketing matters is addressed. In this context corrugated fibreboard, as secondary or tertiary material is essential. In the final section, a comparison between two trade fair stands, representing a corrugated fibreboard company are presented.

  15. Dynamics models and modeling of tree stand development

    Directory of Open Access Journals (Sweden)

    M. V. Rogozin

    2015-04-01

    Full Text Available Brief analysis of scientific works in Russia and in the CIS over the past 100 years. Logical and mathematical models consider the conceptual and show some of the results of their verification. It was found that the models include different laws and the parameters, the sum of which allows you to divide them into four categories: models of static states, development models, models of care for the natural forest and models of cultivation. Each category has fulfilled and fulfills its tasks in economic management. Thus, the model states in statics (table traverse growth played a prominent role in figuring out what may be the most productive (full stands in different regions of the country. However, they do not answer the question of what the initial states lead to the production of complete stands. In a study of the growth of stands used system analysis, and it is observed dominance of works studying static state, snatched from the biological time. Therefore, the real drama of the growth of stands remained almost unexplored. It is no accident there were «chrono-forestry» «plantation forestry» and even «non-traditional forestry», where there is a strong case of a number of new concepts of development stands. That is quite in keeping with Kuhn (Kuhn, 2009 in the forestry crisis began – there were alternative theories and coexist conflicting scientific schools. To develop models of stand development, it is proposed to use a well-known method of repeated observations within 10–20 years, in conjunction with the explanation of the history of the initial density. It mounted on the basis of studying the dynamics of its indicators: the trunk, crown overlap coefficient, the sum of volumes of all crowns and the relative length of the crown. According to these indicators, the researcher selects natural series of development stands with the same initial density. As a theoretical basis for the models it is possible to postulate the general properties of

  16. A New Standing Posture Detector to Enable People with Multiple Disabilities to Control Environmental Stimulation by Changing Their Standing Posture through a Commercial Wii Balance Board

    Science.gov (United States)

    Shih, Ching-Hsiang; Shih, Ching-Tien; Chiang, Ming-Shan

    2010-01-01

    This study assessed whether two persons with multiple disabilities would be able to control environmental stimulation using body swing (changing standing posture) and a Wii Balance Board with a newly developed standing posture detection program (i.e. a new software program turns a Wii Balance Board into a precise standing posture detector). The…

  17. The distribution of lumbar intervertebral angles in upright standing and extension is related to low back pain developed during standing.

    Science.gov (United States)

    Viggiani, Daniel; Gallagher, Kaitlin M; Sehl, Michael; Callaghan, Jack P

    2017-11-01

    Lumbar lordosis measures are poorly related to clinical low back pain, however using a controlled exposure such as prolonged standing to identify pain groups may clarify this relationship. The purpose of this study was to determine the distribution of lumbar intervertebral angles in asymptomatic persons who do (pain developers) and do not (non-pain developers) develop low back pain during standing. Sagittal plane lumbar spine radiographs of eight pain developers and eight non-pain developers were taken in three poses: upright standing, full extension and full flexion. Measures of vertebral end plate orientations from L1 to S1 were taken in each pose to compute: intervertebral angles, contribution of each level to the total curve, total lordosis, ranges of motion, relative pose positioning within the range of motion, vertebral shape, and lumbar spine recurve. Measures were compared between pain groups and lumbar levels. Pain group differences in intervertebral angles and level contributions were greatest in the full extension pose, with pain developers having greater contributions from higher lumbar levels and fewer contributions from lower levels than non-pain developers. Pain group differences in intervertebral angle distributions were less pronounced in upright standing and non-existent in full flexion. No other measures differentiated pain groups. Although participants had similar gross-lumbar spine curvature characteristics, non-pain developers have more curvature at lower levels in upright standing and full extension. These differences in regional vertebral kinematics may partially be responsible for standing-induced low back pain. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Step Prediction During Perturbed Standing Using Center Of Pressure Measurements

    Directory of Open Access Journals (Sweden)

    Milos R. Popovic

    2007-04-01

    Full Text Available The development of a sensor that can measure balance during quiet standing and predict stepping response in the event of perturbation has many clinically relevant applica- tions, including closed-loop control of a neuroprothesis for standing. This study investigated the feasibility of an algorithm that can predict in real-time when an able-bodied individual who is quietly standing will have to make a step to compensate for an external perturbation. Anterior and posterior perturbations were performed on 16 able-bodied subjects using a pul- ley system with a dropped weight. A linear relationship was found between the peak center of pressure (COP velocity and the peak COP displacement caused by the perturbation. This result suggests that one can predict when a person will have to make a step based on COP velocity measurements alone. Another important feature of this finding is that the peak COP velocity occurs considerably before the peak COP displacement. As a result, one can predict if a subject will have to make a step in response to a perturbation sufficiently ahead of the time when the subject is actually forced to make the step. The proposed instability detection algorithm will be implemented in a sensor system using insole sheets in shoes with minitur- ized pressure sensors by which the COPv can be continuously measured. The sensor system will be integrated in a closed-loop feedback system with a neuroprosthesis for standing in the near future.

  19. The stand-alone test and decreasing serial cost sharing

    DEFF Research Database (Denmark)

    Hougaard, Jens Leth; Thorlund-Petersen, Lars

    2000-01-01

    The rule of decreasing serial cost sharing defined in de Frutos [1] over the class of concave cost functions may violate the important stand-alone test. Sufficient conditions for the test to be satisfied are given, in terms of individual rationality as well as coalitional stability...

  20. Logging a roadside stand to protect scenic values

    Science.gov (United States)

    Philip M. McDonald; Raymond V. Whiteley

    1972-01-01

    A case study on the Challenge Experimental Forest, California, demonstrated that logging along roadsides need not despoil roadside stands. Nearly every tree was "viewed" before marking. Because of the "special-care" procedures followed, combined logging and slash-disposal cost was about twice that of a single-tree selection cut.

  1. The energy cost for balance control during upright standing

    NARCIS (Netherlands)

    Houdijk, J.H.P.; Fickert, R.; van Velzen, J.; van Bennekom, C.A.M.

    2009-01-01

    The aim of this study was to investigate whether balance control during a static upright standing task with and without balance perturbations elicits a significant and meaningful metabolic energy demand and to test whether this energy demand correlates with conventional posturography measures for

  2. Statistical sampling and modelling for cork oak and eucalyptus stands

    NARCIS (Netherlands)

    Paulo, M.J.

    2002-01-01

    This thesis focuses on the use of modern statistical methods to solve problems on sampling, optimal cutting time and agricultural modelling in Portuguese cork oak and eucalyptus stands. The results are contained in five chapters that have been submitted for publication

  3. stem and standing heights in bantu and white south africans

    African Journals Online (AJOL)

    1971-05-29

    May 29, 1971 ... Sitting and standing heights have been recorded for Bantu and Whites, males and females. It !Vas found that Bantu males and females have relatively longer lower extremities than White South African males and females. Anthropo- metric differences account for only about 15% of the actual observed ...

  4. 46 CFR Sec. 2 - Stand-by agreements.

    Science.gov (United States)

    2010-10-01

    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION B-CONTROL AND UTILIZATION OF PORTS OPERATING CONTRACT Sec. 2 Stand-by agreements. The Director NSA, Maritime Administration, in advance of an emergency, may negotiate... 1901) under the control of the Maritime Administration and allocated for long term exclusive use by the...

  5. 32 CFR 636.30 - Stopping, standing and parking.

    Science.gov (United States)

    2010-07-01

    ... ENFORCEMENT AND CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION (SPECIFIC INSTALLATIONS) Fort... which obstructs traffic. (g) No driver will stand or park a vehicle, whether occupied or not, except...) Within 20 feet upon the approach to any flashing signal, a stop sign, yield sign, or traffic control...

  6. Photosynthetic Characteristics of Five Hardwood Species in a Mixed Stand

    Science.gov (United States)

    Shi-Jean S. Sung; Paul P. Kormanik; Stanley J. Zarnoch

    1999-01-01

    In 1998, photosythesis (Pn) was measured in cherrybark oak, green ash, swamp chestnut oak, sweetgum, and water hickory in a mixed stand established in February 1994. Based on the apparent quantum yield obtained from light response curves, cherrybark oak had the lowest Pn in August whereas sweetgum, green ash, and water hickory were equally active in Pn. Daily August...

  7. The Relationship Between Foot and Pelvic Alignment While Standing

    Directory of Open Access Journals (Sweden)

    Khamis Sam

    2015-06-01

    Full Text Available A normal motion and segmental interrelationship has been determined as a significant factor in normal function. Yet, the relationship between distal segments and pelvic alignment needs further investigation. The aim of this study was to investigate the interrelationship between distal and proximal lower extremity segments while standing and during induced feet hyperpronation. Changes in alignment of the pelvis and lower extremities were measured at a gait laboratory using the VICON 612 computerized motion analysis system. Thirty-five healthy volunteer subjects were recruited. Four randomized repeated-measure standing modes were used: standing directly on the floor and then on three wedges angled at 10°, 15° and 20° to induce bilateral hyperpronation for 20 seconds. A significant (p<0.05 bi-variate relationship was found between the anterior pelvic tilt and thigh internal rotation, in all four standing positions (.41≤r≤.46, in all p<0.014. A combined effect of rotational alignment between segments and the cumulative effect of foot hyperpronation on pelvic tilt revealed that only the shank significantly affected pelvic alignment, acting as a mediator between a foot and a thigh with the thigh having a crude significant effect on the pelvis. When internal rotation of the shank occurs, calcaneal eversion couples with thigh internal rotation and anterior pelvic tilt. It can be concluded that in response to induced hyperpronation, the shank is a pivotal segment in postural adjustment.

  8. Free standing bulk metallic glass microcomponents: Tooling considerations

    DEFF Research Database (Denmark)

    Byrne, Cormac; Eldrup, Morten Mostgaard; Ohnuma, Masato

    2010-01-01

    Bulk metallic glasses have enormous potential for use in small-scale devices such as MEMS and biomedical components. Thermoplastic forging of free standing components poses challenges unlike those seen when forging crystalline materials. Central to these challenges is the simultaneous advantage/disadvantage...

  9. Localization Problem in the 5D Standing Wave Braneworld

    OpenAIRE

    Gogberashvili, Merab; Midodashvili, Pavle; Midodashvili, Levan

    2012-01-01

    We investigate the problem of pure gravitational localization of matter fields within the 5D standing wave braneworld generated by gravity coupled to a phantom-like scalar field. We show that in the case of increasing warp factor there exist normalizable zero modes of spin-0, -1/2, -1, and -2 fields on the brane.

  10. Assessment framework for standardisation activities ResiStand

    NARCIS (Netherlands)

    Stolk, D.J.; Lee, M.D.E. van der; Petiet, P.J.; Liedtke, C.; Lindner, R.; Zetten, J. van; Karppinen, A.; Anson, S.; Kroener, I.

    2017-01-01

    Standardisation is a powerful tool to achieve better interoperability. However, it needs to overcome a lack of interest and modest participation from stakeholders. Also, promising research results are not always used as the basis for new standards. The overall goal of ResiStand is to find new ways

  11. The standing of the curriculum for consumer studies as school ...

    African Journals Online (AJOL)

    ... systems that consistently perform well in international benchmarking tests. The findings of the research point to the standing of the current Consumer Studies curriculum and its perceived impact in the South African context. Recommendations are made regarding the strengthening of the curriculum and its implementation.

  12. Stand-alone solutions, computer networks and extern communications

    International Nuclear Information System (INIS)

    Tarschisch, H.

    1988-01-01

    The advantages of local networks over stand-alone solutions are presented. Of the local networks (LAN), two are presently at the center of attention: the bus and the ring. ETHERNET and the IBM-Token-Ring are described as typical examples. Access to public networks, especially TELEPAC and ISDN, is discussed. 12 figs

  13. Polarization-dependent ponderomotive gradient force in a standing wave

    NARCIS (Netherlands)

    Smorenburg, P.W.; Kanters, J.H.M.; Lassise, A.; Brussaard, G.J.H.; Kamp, L.P.J.; Luiten, O.J.

    2011-01-01

    The ponderomotive force is derived for a relativistic charged particle entering an electromagnetic standing wave with a general three-dimensional field distribution and a nonrelativistic intensity, using a perturbation expansion method. It is shown that the well-known ponderomotive gradient force

  14. Design of a quadrotor flight test stand for system identification

    CSIR Research Space (South Africa)

    Beharie, MM

    2015-01-01

    Full Text Available This paper presents the design, development and construction of a flight test stand for a quadrotor UAV. As opposed to alternate forms of UAV, the power plant in the case of the quadrotor serves a dual purpose of control and propulsion. Since...

  15. Microbial deterioration of stored water for users supplied by stand ...

    African Journals Online (AJOL)

    Two forms of water service delivery in peri-urban settlements in the eThekwini municipal region are communal stand-pipes and household ground-tanks. Water from these sources requires storage prior to use. Previous studies have shown that water quality tends to deteriorate during storage. This study was conducted ...

  16. Increasing cotton stand establishment in soils prone to soil crusting

    Science.gov (United States)

    Many factors can contribute to poor cotton stand establishment, and cotton is notorious for its weak seedling vigor. Soil crusting can be a major factor hindering cotton seedling emergence in many of the cotton production regions of the US and the world. Crusting is mainly an issue in silty soils ...

  17. Assessing the Economic and Environmental Prospects of Stand-By ...

    African Journals Online (AJOL)

    This paper presents an economic analysis of two stand-by power supply options for a typical Nigerian household namely diesel generator plant and solar powered systems. The analysis reveals that solar systems are the most economically viable. The environmental benefits associated with substituting diesel powered ...

  18. Generalized height-diameter models for Populus tremula L. stands

    African Journals Online (AJOL)

    USER

    2010-07-12

    Jul 12, 2010 ... and stand density) into the base height-diameter models increased the accuracy of prediction for P. tremula. .... parameter estimates compared with those obtained with ... using coefficient of determination for non-linear regression (. 2. R ), ..... stochastic height-diameter model for maritime pine ecoregions in.

  19. Compering and Comparing: Stand-Up Comedy and Pedagogy

    Science.gov (United States)

    McCarron, Kevin; Savin-Baden, Maggi

    2008-01-01

    The central argument of this paper is that adopting some of the techniques practised by stand-up comedians can help teachers in higher education challenge students in ways that will ultimately improve the student learning experience overall. It will suggest that developing co-dependent relationships and over-engaging with students is disabling…

  20. Fungal diseases of tree stands under urbanized conditions of Moscow

    Directory of Open Access Journals (Sweden)

    Smirnova Oksana G.

    2013-01-01

    Full Text Available Phytosanitary and ecological estimation of tree-stands has been con­ducted at the Forest Experimental Station of Moscow Agricultural Academy and parks of Northeast of Moscow in 2007-2011. Fomes fomentarius was proved to be a very serious pathogen of trees under conditions of Moscow, Piptoporus betulinus, Phellinus igniarius, and Fomitopsis pinicola also occurred and caused damage to trees. This rather bad phytosanitary situation depends on alarming ecological situation in Moscow. At the Forest Experimental Station of Moscow Agricultural Academy a number and cover of lichens decreased. In general, all trees in Moscow are in dynamic equilibrium with the urbanized environment. In connection with this, the following classification of tree-stands was proposed for the urbanized environment: 1 - healthy trees, 2 - affected trees which can be managed, 3 - dry woods, 3a - very diseased. Many tree-stands in investigated regions of Moscow are found to belong to the groups 2 and 3c. All tree-stands must be carefully monitored and managed in order to provide a well-timed decision on the support system for preservation of trees as ‘lungs of city’ and avoid unpredictable tree falling which put people and traffic at risk.

  1. Ophiostomatoid fungi associated with declined Pinus pinaster stands in Spain

    Directory of Open Access Journals (Sweden)

    Gonzalo Álvarez

    2015-04-01

    Full Text Available Aim of study: We studied the presence of fungi and distribution patterns in relation to the health status of declining Pinus pinaster trees. Area of study: Trees in two declining stands in Central Spain were allotted to three declining classes. Material and Methods: Trees in two declining stands in Central Spain were allotted to three declining classes (healthy, declining and recently dead and 3 trees of each class were felled in each stand. Wood slides (phloem and xylem were taken at six positions along the trees and samples collected from fungal identification. Main results: A total of 21 fungal taxa were isolated and identified; eleven of these species belonged to the Ophiostomatoid group. Ophiostoma minus was the most frequently isolated fungus and was identified in 22% of the samples, mainly associated to dead and diseased trees. Research highlights: Together these results suggest a putative association of O. minor with the decline in this area, and thus we suggest paying more attention to this fungus as a potential agent of decline in P. pinaster stands.

  2. Forest stand dynamics of shortleaf pine in the Ozarks

    Science.gov (United States)

    David R. Larsen

    2007-01-01

    Much has been written on the management of shortleaf pine in the Ozarks (Brinkman et al. 1965, Brinkman 1967, Brinkman and Smith 1968, Seidel and Rogers 1965, Seidel and Rogers 1966). In large portions of the Ozarks, shortleaf pine does not grow in pure stands but rather in mixes with various oak species. These mixes present unique challenges in finding the set of...

  3. Quantitative Analysis of Complex Tropical Forest Stands: A Review ...

    African Journals Online (AJOL)

    The importance of data analysis in quantitative assessment of natural resources remains significant in the sustainable management of complex tropical forest resources. Analyses of data from complex tropical forest stands have not been easy or clear due to improper data management. It is pivotal to practical researches ...

  4. Sit-to-stand at different periods of pregnancy.

    Science.gov (United States)

    Lou, S Z; Chou, Y L; Chou, P H; Lin, C J; Chen, U C; Su, F C

    2001-03-01

    This study was performed to determine the biomechanics of chair rising by pregnant women. Relative body joint position and ground reaction forces were measured by a motion analysis system and one force plate. Physiological and psychological changes during pregnancy impose postural demands and limit the performance of daily living activities such as rising from sitting to standing position. Twenty-four pregnant women, divided into three groups, were studied performing sit-to-stand transition from an armless and adjustable chair. By kinematic and kinetic analysis, the angles and moments of hip, knee and ankle joints were investigated. The chair height has great influence on knee joint and hip joint moments, but less on ankle joints. In the third trimester for all chair heights, because of a marked increase in abdominal depth, the maximum hip moment is significantly less than that in first trimester, while the maximum knee moment is significantly larger. Pregnant women in third trimester produced larger knee moment during sit-to-stand transition from lower chair height. The mechanism of sit-to-stand is affected by the physical changes of pregnant women at different periods of pregnancy, e.g. increased loading of knee joint and decreased hip joint moment, especially in the last trimester period of pregnancy.

  5. Computer programs for optical dendrometer measurements of standing tree profiles

    Science.gov (United States)

    Jacob R. Beard; Thomas G. Matney; Emily B. Schultz

    2015-01-01

    Tree profile equations are effective volume predictors. Diameter data for building these equations are collected from felled trees using diameter tapes and calipers or from standing trees using optical dendrometers. Developing and implementing a profile function from the collected data is a tedious and error prone task. This study created a computer program, Profile...

  6. Stand tests of the grader unit AKD-2

    Energy Technology Data Exchange (ETDEWEB)

    Kocheskhov, S.M.; Bagley, A.V.; Shalkov, A.V.

    1982-01-01

    Results are presented of stand tests of a static operating grader designed for unmanned extraction of deep beds with programmed control of the unit AKD-2 according to hypsometry of the seam occurrence. Malfunctions in a number of grader assemblies are revealed and eliminated. Parameters are defined which characterize the kinematics and dynamics of the grader mechanism.

  7. Shock stand off Calculations for Hemisphere in Hypersonic Flows

    International Nuclear Information System (INIS)

    Hanif, M.; Ghaffar, A.; Bilal, S.; Zahir, S.; Khan, M.A.

    2004-01-01

    The shape and location of shock has been studied by solving the axi symmetric Navier Stokes Equations for a hemisphere in hypersonic flow. The effect of Mach number on shock stand-off distance has been investigated. It is found that the shock location varies with Mach number and the free stream conditions at a given nose radius. (author)

  8. Standing Slow MHD Waves in Radiatively Cooling Coronal Loops ...

    Indian Academy of Sciences (India)

    The standing slow magneto-acoustic oscillations in cooling coronal loops ... turbation and, eventually, reduces the MHD equations to a 1D system modelling ..... where the function Q is expanded in power series with respect to ǫ, i.e.,. Q = Q0 + ...

  9. Method’s and Test Stand for Electronic PID Controller

    Directory of Open Access Journals (Sweden)

    Cristian Paul Chioncel

    2009-01-01

    Full Text Available The paper presents method’s and a testing stand for electronic controller using for this a signal generator and a digital oscilloscope respectively the virtual instrumentation and the signal acquisitions from the controllers input and output through an data acquisition board and an PC on that Lab View program runs.

  10. Evaluation of three classifiers in mapping forest stand types using ...

    African Journals Online (AJOL)

    EJIRO

    applied for classification of the image. Supervised classification technique using maximum likelihood algorithm is the most commonly and widely used method for land cover classification (Jia and Richards, 2006). In Australia, the maximum likelihood classifier was effectively used to map different forest stand types with high.

  11. Bat use of remnant old-growth redwood stands

    Science.gov (United States)

    William J. Zielinski; Steven T. Gellman

    1999-01-01

    Most of the old-growth redwood (Sequoia sempervirens) in Calfornia has been cut; regenerating forests will probably never resemble those that were harvested, and what old growth remains on private land occurs in small, isolated remnant patches. The landscapes in which these stands occur differ so markedly from their original condition that their...

  12. Ampere hour method of sizing a stand alone photovoltaic system ...

    African Journals Online (AJOL)

    Stand-alone photovoltaic power systems are natural options for application in electrification of remote areas which are not served by the grid electricity supply system. An ampere-hour ... Sizing of the balance-of-system were carefully handled to avoid undersizing or oversizing and subsequent variation in supply reliability.

  13. Economic evaluation of intermediate operations in oak stands

    Science.gov (United States)

    Henry H. Webster; John C., Jr. Meadows

    1971-01-01

    Economic evaluation of forest-management opportunities is a vital ingredient of effective forestry programs. Choices among management opportunities are necessary because opportunities inevitably exceed funds available, and they are important because opportunities commonly range from highly productive to decidedly unproductive. Economic evaluation in oak stands shows a...

  14. Log sampling methods and software for stand and landscape analyses.

    Science.gov (United States)

    Lisa J. Bate; Torolf R. Torgersen; Michael J. Wisdom; Edward O. Garton; Shawn C. Clabough

    2008-01-01

    We describe methods for efficient, accurate sampling of logs at landscape and stand scales to estimate density, total length, cover, volume, and weight. Our methods focus on optimizing the sampling effort by choosing an appropriate sampling method and transect length for specific forest conditions and objectives. Sampling methods include the line-intersect method and...

  15. Distribution and dynamics of hayscented fern following stand harvest

    Science.gov (United States)

    Songlin Fei; Peter J. Gould; Melanie J. Kaeser; Kim C. Steiner

    2008-01-01

    The distribution and dynamics of hayscented fern were examined as part of a large-scale study of oak regeneration in Pennsylvania. The study included 69 stands covering 3,333 acres in two physiographic provinces. Hayscented fern was more widely distributed and occurred at higher densities in the Allegheny Plateau physiographic provinces versus the Ridge and Valley...

  16. Standing in the Hallway Improves Students' Understanding of Conformity

    Science.gov (United States)

    Lawson, Timothy J.; Haubner, Richard R.; Bodle, James H.

    2013-01-01

    To help beginning psychology students understand how they are influenced by social pressures to conform, we developed a demonstration designed to elicit their conformity to a small group of students standing in the hallway before class. Results showed the demonstration increased students' recognition of their own tendency to conform, knowledge of…

  17. 48 CFR 13.103 - Use of standing price quotations.

    Science.gov (United States)

    2010-10-01

    ... quotations. 13.103 Section 13.103 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... price quotations. Authorized individuals do not have to obtain individual quotations for each purchase. Standing price quotations may be used if— (a) The pricing information is current; and (b) The Government...

  18. Acoustic evaluation of standing trees : recent research development

    Science.gov (United States)

    Xiping Wang; Robert J. Ross; Peter Carter

    2005-01-01

    This paper presents some research results from recent trial studies on measuring acoustic velocities on standing trees of five softwood species. The relationships between tree velocities measured by time of flight method and log velocities measured by resonance method were evaluated. Theoretical and empirical models were developed for adjusting observed tree velocity...

  19. Stand age and climate drive forest carbon balance recovery

    Science.gov (United States)

    Besnard, Simon; Carvalhais, Nuno; Clevers, Jan; Herold, Martin; Jung, Martin; Reichstein, Markus

    2016-04-01

    Forests play an essential role in the terrestrial carbon (C) cycle, especially in the C exchanges between the terrestrial biosphere and the atmosphere. Ecological disturbances and forest management are drivers of forest dynamics and strongly impact the forest C budget. However, there is a lack of knowledge on the exogenous and endogenous factors driving forest C recovery. Our analysis includes 68 forest sites in different climate zones to determine the relative influence of stand age and climate conditions on the forest carbon balance recovery. In this study, we only included forest regrowth after clear-cut stand replacement (e.g. harvest, fire), and afforestation/reforestation processes. We synthesized net ecosystem production (NEP), gross primary production (GPP), ecosystem respiration (Re), the photosynthetic respiratory ratio (GPP to Re ratio), the ecosystem carbon use efficiency (CUE), that is NEP to GPP ratio, and CUEclimax, where GPP is derived from the climate conditions. We implemented a non-linear regression analysis in order to identify the best model representing the C flux patterns with stand age. Furthermore, we showed that each C flux have a non-linear relationship with stand age, annual precipitation (P) and mean annual temperature (MAT), therefore, we proposed to use non-linear transformations of the covariates for C fluxes'estimates. Non-linear stand age and climate models were, therefore, used to establish multiple linear regressions for C flux predictions and for determining the contribution of stand age and climate in forest carbon recovery. Our findings depicted that a coupled stand age-climate model explained 33% (44%, average site), 62% (76%, average site), 56% (71%, average site), 41% (59%, average site), 50% (65%, average site) and 36% (50%, average site) of the variance of annual NEP, GPP, Re, photosynthetic respiratory ratio, CUE and CUEclimax across sites, respectively. In addition, we showed that gross fluxes (e.g. GPP and Re) are

  20. Atmospheric deposition in coniferous and deciduous tree stands in Poland

    Science.gov (United States)

    Kowalska, Anna; Astel, Aleksander; Boczoń, Andrzej; Polkowska, Żaneta

    2016-05-01

    The objective of this study was to assess the transformation of precipitation in terms of quantity and chemical composition following contact with the crown layer in tree stands with varied species composition, to investigate the effect of four predominant forest-forming species (pine, spruce, beech, and oak) on the amount and composition of precipitation reaching forest soils, and to determine the sources of pollution in atmospheric precipitation in forest areas in Poland. The amount and chemical composition (pH, electric conductivity, alkalinity, and chloride, nitrate, sulfate, phosphate, ammonium, calcium, magnesium, sodium, potassium, iron aluminum, manganese, zinc, copper, total nitrogen, and dissolved organic carbon contents) of atmospheric (bulk, BP) and throughfall (TF) precipitation were studied from January to December 2010 on twelve forest monitoring plots representative of Polish conditions. The study results provided the basis for the determination of the fluxes of pollutants in the forest areas of Poland and allowed the comparison of such fluxes with values provided in the literature for European forest areas. The transformation of precipitation in the canopy was compared for different tree stands. The fluxes of substances in an open field and under canopy were influenced by the location of the plot, including the regional meteorological conditions (precipitation amounts), vicinity of the sea (effect of marine aerosols), and local level of anthropogenic pollution. Differences between the plots were higher in TF than in BP. The impact of the vegetation cover on the chemical composition of precipitation depended on the region of the country and dominant species in a given tree stand. Coniferous species tended to cause acidification of precipitation, whereas deciduous species increased the pH of TF. Pine and oak stands enriched precipitation with components that leached from the canopy (potassium, manganese, magnesium) to a higher degree than spruce and

  1. Measuring Diagnostic Stand for Experimental Researches in Technology Machining

    Directory of Open Access Journals (Sweden)

    A. E. Dreval'

    2014-01-01

    Full Text Available The paper reviews applied techniques, methods, and structure of the control and measuring means to conduct experimental and scientific researches of cutting processes. Existing research methods in cutting the metals are divided by features, such as essence of methods, the number of records of physical indicators, the number of studied factors, duration of tests. The groups of methods are briefly characterized.The chair "Tool Engineering and Technologies" of BMSTU developed and made a diagnostic stand of control and measurements for conducting research activities in the field of materials processing technology by cutting to define rational technological decisions, when machining, and carry out an analysis of efficiency and economic feasibility of made decisions. The diagnostic stand contains modern the electronic equipment. Record of measuring parameters is made in real time with a possibility for visual representation of read results and mathematical and statistical processing of measurement results. The stand can be used in research laboratories of machine-building enterprises, laboratories of higher education institutions, and other scientific divisions.The paper presents a justification that the stand is reasonable to use for the following: completion and choice of rational cutting modes, workability assessment of new constructional materials, technical and operational characteristics of the processed surfaces, and operational properties of the cutting tools of various producers, choice of optimum geometrical parameters of the cutting tools and brands of the lubricant cooling technological means, as well as the energy consumption for the chosen machining process. The stand allows us to make an assessment of wear resistance and tribology-technical characteristics of tool materials, as well as an accuracy, rigidity, vibration stability of machines, both new and being in operation.

  2. Direct measurement of the intrinsic ankle stiffness during standing.

    Science.gov (United States)

    Vlutters, M; Boonstra, T A; Schouten, A C; van der Kooij, H

    2015-05-01

    Ankle stiffness contributes to standing balance, counteracting the destabilizing effect of gravity. The ankle stiffness together with the compliance between the foot and the support surface make up the ankle-foot stiffness, which is relevant to quiet standing. The contribution of the intrinsic ankle-foot stiffness to balance, and the ankle-foot stiffness amplitude dependency remain a topic of debate in the literature. We therefore developed an experimental protocol to directly measure the bilateral intrinsic ankle-foot stiffness during standing balance, and determine its amplitude dependency. By applying fast (40 ms) ramp-and-hold support surface rotations (0.005-0.08 rad) during standing, reflexive contributions could be excluded, and the amplitude dependency of the intrinsic ankle-foot stiffness was investigated. Results showed that reflexive activity could not have biased the torque used for estimating the intrinsic stiffness. Furthermore, subjects required less recovery action to restore balance after bilateral rotations in opposite directions compared to rotations in the same direction. The intrinsic ankle-foot stiffness appears insufficient to ensure balance, ranging from 0.93±0.09 to 0.44±0.06 (normalized to critical stiffness 'mgh'). This implies that changes in muscle activation are required to maintain balance. The non-linear stiffness decrease with increasing rotation amplitude supports the previous published research. With the proposed method reflexive effects can be ruled out from the measured torque without any model assumptions, allowing direct estimation of intrinsic stiffness during standing. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Silvicultural interpretation of natural vegetation dynamics in ageing Scots pine stands for their conversion into mixed broadleaved stands

    NARCIS (Netherlands)

    Kint, V.; Geudens, G.; Mohren, G.M.J.; Lust, N.

    2006-01-01

    In many West-European regions there is principal consensus on the conversion of homogeneous even-aged Scots pine plantations into mixed broadleaved stands. In recent years, interest is growing for conversion management in which managers try to maximise the use of natural processes by steering or

  4. Tree regeneration and future stand development after bark beetle infestation and harvesting in Colorado lodgepole pine stands

    Science.gov (United States)

    Byron J. Collins; Charles C. Rhoades; Robert M. Hubbard; Michael A. Battaglia

    2011-01-01

    In the southern Rocky Mountains, current mountain pine beetle (Dendroctonus ponderosae Hopkins) outbreaks and associated harvesting have set millions of hectares of lodgepole pine (Pinus contorta var. latifolia Engelm. ex Wats.) forest onto new stand development trajectories. Information about immediate, post-disturbance tree regeneration will provide insight on...

  5. Rehabilitation of Understocked Loblolly-Shortleaf Pine Stands - II. Development of Intermediate and Suppressed Trees Following Release in Natural Stands

    Science.gov (United States)

    James B. Baker; Michael G. Shelton

    1998-01-01

    Development of 86 intermediate and suppressed loblolly pine (Pinus taeda L.) trees, that had been recently released from overtopping pines and hardwoods, was monitored over a 15 year period. The trees were growing in natural stands on good sites (site index = 90 ft at 50 years) that had been recently cut to stocking levels ranging from 10 to 50 percent. At time of...

  6. Stand dynamics following gap-scale exogenous disturbance in a single cohort mixed species stand in Morgan County, Tennessee

    Science.gov (United States)

    Brian S. Hughett; Wayne K. Clatterbuck

    2014-01-01

    Differences in composition, structure, and growth under canopy gaps created by the mortality of a single stem were analyzed using analysis of variance under two scenarios, with stem removed or with stem left as a standing snag. There were no significant differences in composition and structure of large diameter residual stems within upper canopy strata. Some...

  7. Clinical ketosis and standing behavior in transition cows.

    Science.gov (United States)

    Itle, A J; Huzzey, J M; Weary, D M; von Keyserlingk, M A G

    2015-01-01

    Ketosis is a common disease in dairy cattle, especially in the days after calving, and it is often undiagnosed. The objective of this study was to compare the standing behavior of dairy cows with and without ketosis during the days around calving to determine if changes in this behavior could be useful in the early identification of sick cows. Serum β-hydroxybutyrate (BHBA) was measured in 184 cows on a commercial dairy farm twice weekly from 2 to 21d after calving. Standing behavior was measured from 7d before calving to 21d after calving using data loggers. Retrospectively, 15 cows with clinical ketosis (3 consecutive BHBA samples >1.2mmol/L and at least one sample of BHBA >2.9mmol/L) were matched with 15 nonketotic cows (BHBA ketosis occurred 4.5±2.1d after calving. Total daily standing time was longer for clinically ketotic cows compared with nonketotic cows during wk -1 (14.3±0.6 vs. 12.0±0.7h/d) and on d 0 (17.2±0.9 vs. 12.7±0.9h/d) but did not differ during the other periods. Clinically ketotic cows exhibited fewer standing bouts compared with nonketotic cows on d 0 only (14.6±1.9 vs. 20.9±1.8bouts/d). Average standing bout duration was also longer for clinically ketotic cows on d 0 compared with nonketotic cows [71.3min/bout (CI: 59.3 to 85.5) vs. 35.8min/bout (CI: 29.8 to 42.9)] but was not different during the other periods. Differences in standing behavior in the week before and on the day of calving may be useful for the early detection of clinical ketosis in dairy cows. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  8. Logging in hardwood stands established on farm land

    International Nuclear Information System (INIS)

    Bjoerheden, R.

    1992-01-01

    Performance and costs for different harvesting systems in broad leaf stands established on former tillage is presented. The calculations, combined with a forecast of the market development, shows that it is risky to aim production exclusively at bulk products as fibre or fibre/energy. The harvest of fibre or energy wood can, however, be used as a means to increase profitability of a silvicultural programme aimed at production of high quality hardwood lumber. Management and logging in these stands will be carried out with small scale technology, often by the private forest owner. Todays large scale systems are not competitive in these stands. The cost calculations show that we lack economically sound systems for harvesting stands in the interval up to 5 cm DBH. The lowest logging cost for these stands was calculated for motor manual felling and chipping with a chipper/dumper mounted on a farm tractor. This alternative is competitive also in the interval 5-10 cm DBH but there is a number of other feasible systems, e.g. off-road chippers processing motor manually felled and piled trees. Tree section systems with extraction by forwarder or a farm tractor with grapple loader and a bogic trailer operates at low costs to roadside but costs for processing and, maybe, a more expensive secondary transportation must then be added. For thinnings in the interval 10-25 cm DBH tree chipping is the most cost efficient if only energy assortments is to be harvested. However, at the current price relations between energy wood and pulpwood tree section systems are preferable also in stands over 10 cm since it allows a combined harvest of fibre and energy. For the same reason, the seemingly most interesting system in later thinnings is a system with differentiated processing. The term denotes a system where pulpwood is cut motor manually down to 12.5 cm and extracted by forwarder or farm tractor. The remaining tops and branches are processed by an off-road chipper. (36 refs., 11 figs.)

  9. Reproductive biology in monoecious and gynoecious cucumber cultivars as a result of IBA application Biologia reprodutiva de cultivares monóicas e ginóicas de pepino em função do uso de AIB

    Directory of Open Access Journals (Sweden)

    Valdir Diola

    2008-03-01

    concentration.A compreensão da biologia reprodutiva e da regulação da expressão sexual das flores do pepineiro (Cucumis sativus pode facilitar o manejo do cultivo e melhorar a produção e a qualidade dos frutos. O objetivo do presente estudo foi avaliar a resposta fisiológica dos verticilos florais à aplicação de AIB em pepino. O experimento foi conduzido em casa-de-vegetação, em blocos casualizados, com os tratamentos dispostos em fatorial 5 x 2 (AIB nas concentrações de 0, 50, 100, 200 e 500 ìmol, para as cultivares Wisconsin MR28, ginóica, e Caipira, monóica. Foram utilizadas quatro repetições, com quatro plantas por parcela. A cultivar Wisconsin MR28 produziu em média 7.636 grãos de pólen (GP por flor, com resposta linear positiva ao aumento nas concentrações de AIB. Já na cultivar Caipira (5.160 GP, todas as concentrações de AIB interferiram negativamente na produção de GP. As cultivares não diferiram entre si e em ambas houve efeito linear positivo da concentração de AIB sobre a viabilidade dos GP (germinação média in vitro de 75,4 e 79,9% para as cultivares Wisconsin MR28 e Caipira, respectivamente. As cultivares Wisconsin MR28 e Caipira apresentaram em média 71,6 e 70,6 sementes por fruto respectivamente, respondendo com aumento no número de sementes e melhoria do aspecto do fruto ao incremento da concentração de AIB. A relação de flores masculinas:femininas diferiu significativamente entre cultivares (4,2:1 e 3,5:1 respectivamente para as cultivares Wisconsin MR28 e Caipira e foi afetada de forma distinta nas duas cultivares pelas concentrações de AIB: concentrações próximas de 100 µmol aumentaram o número de flores masculinas na cultivar Caipira e reduziram na cultivar Wisconsin MR28. A quantidade de flores femininas foi semelhante entre as cultivares e relativamente constante na cultivar Caipira nas diferentes concentrações de AIB. Já na cultivar Wisconsin MR 28, houve aumento do número de flores femininas em fun

  10. Imaging height fluctuations in free-standing graphene membranes

    Science.gov (United States)

    Dorsey, Kyle; Miskin, Marc; Barnard, Arthur; Rose, Peter; Cohen, Itai; McEuen, Paul

    We present a technique based on multi-wavelength interference microscopy to measure the heights of observed ripples in free-standing graphene membranes. Graphene membranes released from a transparent substrate produce interference fringes when viewed in the reflection mode of an inverted microscope(Blees et. al. Nature 524 (7564): 204-207 (2015)). The fringes correspond to corrugation of the membrane as it floats near an interface. A single set of fringes is insufficient to uniquely determine the height profile, as a given fringe spacing can correspond to an increase or decrease in height by λ / 2 . Imaging at multiple wavelengths resolves the ambiguities in phase, and enables unique determination of the height profile of the membrane (Schilling et. al.Phys. Rev. E, 69:021901, 2004). We utilize this technique to map out the height fluctuations in free-standing graphene membranes to answer questions about fundamental mechanical properties of two-dimensional materials.

  11. Customizable nanotweezers for manipulation of free-standing nanostructures

    DEFF Research Database (Denmark)

    Bøggild, Peter; Hansen, Torben Mikael; Mølhave, Kristian

    2001-01-01

    We present a novel nanotweezer device for manipulation and measurement of free-standing nanostructures, where the shape of the tweezer tips can be customized for the application. Electrostatic actuators with submicron interelectrode spacings are fabricated on a batch level using silicon microfabr......We present a novel nanotweezer device for manipulation and measurement of free-standing nanostructures, where the shape of the tweezer tips can be customized for the application. Electrostatic actuators with submicron interelectrode spacings are fabricated on a batch level using silicon...... microfabrication techniques. The actuators are capable of opening and closing with respect to the neutral position, and the full range of actuation exceeds 330 nm. The nanotweezer tips are fabricated using electron beam induced deposition; an electron beam of a scanning electron microscope is focused at the ends...

  12. Modeling of SAR returns from a red pine stand

    Science.gov (United States)

    Lang, R. H.; Kilic, O.; Chauhan, N. S.; Ranson, J.

    1992-01-01

    Bright P-band radar returns from red pine forests have been observed on synthetic aperture radar (SAR) images in Bangor, Maine. A plot of red pine trees was selected for the characterization and modeling to understand the cause of the high P-band returns. The red pine stand under study consisted of mature trees. Diameter at breast height (DBH) measurements were made to determine stand density as a function of tree diameter. Soil moisture and bulk density measurements were taken along with ground rough surface profiles. Detailed biomass measurements of the needles, shoots, branches, and trunks were also taken. These site statistics have been used in a distorted Born approximation model of the forest. Computations indicate that the direct-reflected or the double-bounce contributions from the ground are responsible for the high observed P-band returns for HH polarization.

  13. Electrical conductivity of free-standing mesoporous silicon thin films

    International Nuclear Information System (INIS)

    Khardani, M.; Bouaicha, M.; Dimassi, W.; Zribi, M.; Aouida, S.; Bessais, B.

    2006-01-01

    The effective electrical conductivity of free-standing p + -type porous silicon layers having porosities ranging from 30% to 80% was studied at both experimental and theoretical sides. An Effective Medium Approximation (EMA) model was used as a theoretical support. The porous silicon (PS) films were prepared by the electrochemical etching method for different values of the anodic current density. In order to model the PS electrical conductivity, the free-standing porous layer was assumed to be formed of three phases; vacuum, oxide and Si nanocrystallites. The analytical expression of the electrical conductivity of the Si nanocrystallites was established using the quantum confinement theory. This enables us to correlate the electrical conductivity of the mesoporous film to the value of the effective band gap energy estimated from the absorption coefficient. A perfect agreement between the theoretical and the experimental electrical conductivity values was obtained for all prospected PS porosities

  14. Optimisation of the test policy of stand-by systems

    International Nuclear Information System (INIS)

    Signoret, J.P.; Muron, O.; Cohen, G.

    1980-09-01

    In a nuclear power plant there are several systems which are on stand-by position as, for instance, safety systems. These stand-by systems have to be ready to start as soon as any situation for which they have be designed occurs. A test policy is then necessary in order to know the state of such a system and repair the possible failures. The tests are normally performed at regular intervals of time according to a scheduled sequence. We have already shown during the 'IIIeme Congres National de Fiabilite' held in Perros-Guirec in 1976 how it is possible in this case to find the optimum test interval leading to the best mean availability of the system. It is, in fact, possible, to improve that by considering that if the test interval is fixed 'a priori' this does not allow to take into account information we have on the system state every time [fr

  15. Equipment for linking source stand and film holder carriage

    International Nuclear Information System (INIS)

    Fajt, P.; Zeman, M.

    1987-01-01

    A device is described for precision link-up of a source stand provided with a spring-loaded cam and a film holder carriage provided with an arm with catches. The catches are mechanically connected to a control device firmly connected to the bottom part of the film holder carriage arm. The cam whose extended part is slidably mounted in the cover guide is secured in position with springs fitted from both sides. The control device consists of an electromagnet with armature connected to the control device pull-rod. The pull-rod provides mechanical connection of the catches and the control device. Upon pressing the pushbutton, the catches automatically engage the film holder cariage arm so that the motorized source stand operates without connection to the carriage. This significantly facilitates the operation of the equipment and reduces physical effort of the technician. The most significant advantage is the possibility of immediate change in operation mode. (J.B.). 5 figs

  16. A Cryogenic Test Stand for LHC Quadrupole Magnets

    International Nuclear Information System (INIS)

    Carcagno, R.H.; Huang, Y.; Orris, D.F.; Peterson, T.J.; Rabehl, R.J.

    2004-01-01

    A new test stand for testing LHC interaction region (IR) quadrupole magnets at the Fermilab Magnet Test Facility has been designed and operated. The test stand uses a double bath system with a lambda plate to provide the magnet with a stagnant bath of pressurized He II at 1.9 K and 0.13 MPa. A cryostated magnet 0.91 m in diameter and up to 13 m in length can be accommodated. This paper describes the system design and operation. Issues related to both 4.5 K and 1.9 K operations and magnet quenching are highlighted. An overview of the data acquisition and cryogenics controls systems is also included

  17. Safe lengthening of a drillpipe string by stands

    Energy Technology Data Exchange (ETDEWEB)

    Karapetyan, K.V.; Khrennikov, S.B.; Voyevoda, A.N.

    1979-01-01

    In order to prevent dragging of the block and tackle under the ground block, each drilling rig is equipped with block and tackle lift limiter. However these devices reduce the useful height of the derricks. Studies were carried out to achieve safe conditions for lengthening drillpipe strings with stands and advance of the borehole with a set of drilling stands. The basic precepts of this research were used to design the new drilling rig Uralmash-3000 EUK. In addition an increase of derrick height by 2.5 m was recommended for effective use of production drilling rigs BU-80. In order to lengthen the derrick a special support under the crown block articulated to the upper sections of the feet of the derrick with a frame under the crown block should be used.

  18. [Optimal solution and analysis of muscular force during standing balance].

    Science.gov (United States)

    Wang, Hongrui; Zheng, Hui; Liu, Kun

    2015-02-01

    The present study was aimed at the optimal solution of the main muscular force distribution in the lower extremity during standing balance of human. The movement musculoskeletal system of lower extremity was simplified to a physical model with 3 joints and 9 muscles. Then on the basis of this model, an optimum mathematical model was built up to solve the problem of redundant muscle forces. Particle swarm optimization (PSO) algorithm is used to calculate the single objective and multi-objective problem respectively. The numerical results indicated that the multi-objective optimization could be more reasonable to obtain the distribution and variation of the 9 muscular forces. Finally, the coordination of each muscle group during maintaining standing balance under the passive movement was qualitatively analyzed using the simulation results obtained.

  19. Effect of Forcing Function on Nonlinear Acoustic Standing Waves

    Science.gov (United States)

    Finkheiner, Joshua R.; Li, Xiao-Fan; Raman, Ganesh; Daniels, Chris; Steinetz, Bruce

    2003-01-01

    Nonlinear acoustic standing waves of high amplitude have been demonstrated by utilizing the effects of resonator shape to prevent the pressure waves from entering saturation. Experimentally, nonlinear acoustic standing waves have been generated by shaking an entire resonating cavity. While this promotes more efficient energy transfer than a piston-driven resonator, it also introduces complicated structural dynamics into the system. Experiments have shown that these dynamics result in resonator forcing functions comprised of a sum of several Fourier modes. However, previous numerical studies of the acoustics generated within the resonator assumed simple sinusoidal waves as the driving force. Using a previously developed numerical code, this paper demonstrates the effects of using a forcing function constructed with a series of harmonic sinusoidal waves on resonating cavities. From these results, a method will be demonstrated which allows the direct numerical analysis of experimentally generated nonlinear acoustic waves in resonators driven by harmonic forcing functions.

  20. Models for a stand-alone PV system

    DEFF Research Database (Denmark)

    Hansen, A.D.; Sørensen, Poul Ejnar; Hansen, L.H.

    2001-01-01

    are based on the model descriptions found in the literature. The battery model is developed at UMASS and is known as the Kinetic Battery Model(KiBaM). The other component models in the PV system are based on simple electrical knowledge. The implementation is done using Matlab/Simulink, a simulation program......This report presents a number of models for modelling and simulation of a stand-alone photovoltaic (PV) system with a battery bank verified against a system installed at Risø National Laboratory. The work has been supported by the Danish Ministry ofEnergy, as a part of the activities in the Solar...... Energy Centre Denmark. The study is carried out at Risø National Laboratory with the main purpose to establish a library of simple mathematical models for each individual element of a stand-alone PVsystem, namely solar cells, battery, controller, inverter and load. The models for PV module and battery...

  1. Volatile monoterpenes in a stand of Picea abies (L.) Karst

    International Nuclear Information System (INIS)

    Schuermann, W.; Eichstaedter, G.; Steinbrecher, R.; Schoenwitz, R.; Gabriel, R.; Karbach, I.; Zufall, N.; Ziegler, H.

    1992-01-01

    Natural emissions of terpene and their fate in the atmosphere were investigated in a forest stand of the Bayerischer Wald mountains. Terpenes are volatile hydrocarbons whose relevance for air chemistry has increased considerably in the past few years. The investigation compared different sources of terpene in order to determine their strength as a function of meteorological, air-chemical and biological parameters. (orig./BBR) [de

  2. Optimal sizing method for stand-alone photovoltaic power systems

    Energy Technology Data Exchange (ETDEWEB)

    Groumpos, P P; Papageorgiou, G

    1987-01-01

    The total life-cycle cost of stand-alone photovoltaic (SAPV) power systems is mathematically formulated. A new optimal sizing algorithm for the solar array and battery capacity is developed. The optimum value of a balancing parameter, M, for the optimal sizing of SAPV system components is derived. The proposed optimal sizing algorithm is used in an illustrative example, where a more economical life-cycle cost has bene obtained. The question of cost versus reliability is briefly discussed.

  3. Quantifying the Lateral Bracing Provided by Standing Steam Roof Systems

    OpenAIRE

    Sorensen, Taylor J.

    2016-01-01

    One of the major challenges of engineering is finding the proper balance between economical and safe. Currently engineers at Nucor Corporation have ignored the additional lateral bracing provided by standing seam roofing systems to joists because of the lack of methods available to quantify the amount of bracing provided. Based on the results of testing performed herein, this bracing is significant, potentially resulting in excessively conservative designs and unnecessary costs. This proje...

  4. Climate-induced mortality of spruce stands in Belarus

    Science.gov (United States)

    Kharuk, Viacheslav I.; Im, Sergei T.; Dvinskaya, Maria L.; Golukov, Alexei S.; Ranson, Kenneth J.

    2015-12-01

    The aim of this work is an analysis of the causes of spruce (Picea abies L.) decline and mortality in Belarus. The analysis was based on forest inventory and Landsat satellite (land cover classification, climate variables (air temperature, precipitation, evaporation, vapor pressure deficit, SPEI drought index)), and GRACE-derived soil moisture estimation (equivalent of water thickness anomalies, EWTA). We found a difference in spatial patterns between dead stands and all stands (i.e., before mortality). Dead stands were located preferentially on relief features with higher water stress risk (i.e., higher elevations, steeper slopes, south and southwestern exposure). Spruce mortality followed a series of repeated droughts between 1990 and 2010. Mortality was negatively correlated with air humidity (r = -0.52), and precipitation (r = -0.57), and positively correlated with the prior year vapor pressure deficit (r = 0.47), and drought increase (r = 0.57). Mortality increased with the increase in occurrence of spring frosts (r = 0.5), and decreased with an increase in winter cloud cover (r = -0.37). Spruce mortality was negatively correlated with snow water accumulation (r = -0.81) and previous year anomalies in water soil content (r = -0.8). Weakened by water stress, spruce stands were attacked by pests and phytopathogens. Overall, spruce mortality in Belarussian forests was caused by drought episodes and drought increase in synergy with pest and phytopathogen attacks. Vast Picea abies mortality in Belarus and adjacent areas of Russia and Eastern Europe is a result of low adaptation of that species to increased drought. This indicates the necessity of spruce replacement by drought-tolerant indigenous (e.g., Pinus sylvestris, Querqus robur) or introduced (e.g., Larix sp. or Pseudotsuga menzieslii) species to obtain sustainable forest growth management.

  5. Abundance of juvenile eastern box turtles in manages forest stands

    Science.gov (United States)

    Z. Felix; Y. Wang; H. Czech; C. Schweitzer

    2008-01-01

    Between 2002 and 2005, we used drift fences and artificial pools to sample juvenile eastern box turtles (Terrapene carolina) in northeastern Alabama in forest stands experimentally treated to retain various amounts of overstory trees—clear-cuts and those with 25%–50% and 75%–100% of trees retained.We captured juvenile turtles only in clear-cut and 25%–50% retention...

  6. 1+-n+ ECR ION SOURCE DEVELOPMENT TEST STAND

    International Nuclear Information System (INIS)

    Donald P. May

    2006-01-01

    A test stand for the investigation of 1+-n+ charge boosting using an ECR ion sources is currently being assembled at the Texas A and M Cyclotron Institute. The ultimate goal is to relate the charge-boosting of ions of stable species to possible charge-boosting of ions of radioactive species extracted from the diverse, low-charge-state ion sources developed for radioactive ion beams

  7. X-ray radiography equipment for patients in standing position

    International Nuclear Information System (INIS)

    Snijder, J.G.N.

    1974-01-01

    X-ray radiography equipment suited for patients in standing position is described. The patient's body centre of mass is indicated by its vertical projection line appearing on the X-ray image. To that end, an X-ray absorbing wire is positioned through the centre of mass by means of an electrical signal acting on a servomotor and derived from the pressure on three non-colinear points in the foot plate through an analogue computer

  8. On the pressure field of nonlinear standing water waves

    Science.gov (United States)

    Schwartz, L. W.

    1980-01-01

    The pressure field produced by two dimensional nonlinear time and space periodic standing waves was calculated as a series expansion in the wave height. The high order series was summed by the use of Pade approximants. Calculations included the pressure variation at great depth, which was considered to be a likely cause of microseismic activity, and the pressure distribution on a vertical barrier or breakwater.

  9. Use of stand of climatic influences for radiobiology researches

    International Nuclear Information System (INIS)

    Nenakhov, A.N.; Senyuk, O.F.

    2005-01-01

    In the real life the ionizing radiations render influence on a man in a complex with other low-intensive factors - chemical contaminations, electromagnetic, noise, vibration, temperature influences, psycho-emotional tension and other. For the study of effects of imposition of microclimate and radiation factor influencing on a man it is suggested to use the stand of climatic influence, allowing to set and control the parameters of gamma- and the neutron fields, temperature and humidity of external environment

  10. Project of a test stand for cyclotron ion sources

    International Nuclear Information System (INIS)

    Buettig, H.; Dietrich, J.; Merker, H.; Odrich, H.; Preusche, S.; Weissig, J.

    1978-10-01

    In the work the construction of a test stand for testing and optimization of ion sources of the Rossendorf cyclotron U-120 is represented. The design procedure and the construction of the electromagnet, the vacuum chamber with monant, the vacuum system, the power supply and the detecting system are demonstrated. The results of calculations of the motion of ions in the magnetic field are presented. (author)

  11. Commissioning and First Results from the Fermilab Cryomodule Test Stand

    Energy Technology Data Exchange (ETDEWEB)

    Harms, Elvin; et al.

    2017-05-01

    A new test stand dedicated to SRF cryomodule testing, CMTS1, has been commissioned and is now in operation at Fermilab. The first device to be cooled down and powered in this facility is the prototype 1.3 GHz cryomodule assembled at Fermilab for LCLS-II. We describe the demonstrated capabilities of CMTS1, report on steps taken during commissioning, provide an overview of first test results, and survey future plans.

  12. Stand for visual ultrasonic testing of spent fuel

    International Nuclear Information System (INIS)

    Czajkowski, W.; Borek-Kruszewska, E.

    2001-01-01

    A stand for visual and ultrasonic testing of spent fuel, constructed under Strategic Governmental Programme for management of spent fuel and radioactive waste, is presented in the paper. The stand, named 'STEND-1', built up at the Institute of Atomic Energy in Swjerk, is appointed for underwater visual testing of spent fuel elements type MR6 and WWR by means of TV-CCD camera and image processing system and for ultrasonic scanning of external surface of these elements by means of video scan immersion transducer and straight UHT connector. 'STEND-1' is built using flexible in use, high-tensile, anodized aluminum profiles. All the profiles feature longitudinal grooves to accommodate connecting elements and for the attachment of accessories at any position. They are also characterised by straight-through core bores for use with standard fastening elements and to accommodate accessory components. Stand, equipped with automatic control and processing system based on personal computer, may be manually or automatically controlled. Control system of movements of the camera in the vertical axis and rotational movement of spent fuel element permits to fix chosen location of fuel element with accuracy better than 0.1 mm. High resolution of ultrasonic method allows to record damages of outer surface of order 0.1 mm. The results of visual testing of spent fuel are recorded on video tape and then may be stored on the hard disc of the personal computer and presented in shape of photo or picture. Only selected damage surfaces of spent fuel elements are tested by means of ultrasonic scanning. All possibilities of the stand and results of visual testing of spent fuel type WWR are presented in the paper. (author)

  13. Saturn V First Stage Leaves the Dynamic Test Stand

    Science.gov (United States)

    1967-01-01

    This photo shows the Saturn V first stage being lowered to the ground following a successful test to determine the effects of continual vibrations simulating the effects of an actual launch. The towering 363-foot Saturn V was a multi-stage, multi-engine launch vehicle standing taller than the Statue of Liberty. Altogether, the Saturn V engines produced as much power as 85 Hoover Dams.

  14. Penerapan Analisis Diskriminan dalam Pembedaan Kelas Umur Tegakan Pinus (Discriminant Analysist for Stand Class Age Distinction of Pine Stand

    Directory of Open Access Journals (Sweden)

    Priyanto .

    2011-01-01

    Full Text Available Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} This  study  describes the use of discriminant anylisis for pine (Pinus spp. stand class age distinction.    Aim of this  study were (1 to arrange stand age class based on variable of aerial photograph by non hierarchy cluster analysis,  and (2 to find out aerial  photograph variable contribute to stand age class distinction by discriminant analysis.    Data used in study was taken from  a  research  conducted by Adi (1998.   Pinus stand was located  in KPH Bandung Utara, West Java. The variable of aerial photograph that used in this analysis were tone, shape, texture, topography, pattern, crown, diameter and height. The result showed that validation analysis of discriminant function was significant.  Therefore, this function was applicable for grouping new object to stand age class based on discriminant score. Keywords: cluster analysis, discriminat analysis, stand age class, discriminant score

  15. Stand-off detection of chemicals by UV Raman spectroscopy

    International Nuclear Information System (INIS)

    Wu, Ming; Ray, Mark; Hang Fung, K.; Ruckman, Mark W.; Harder, David; Sedlacek, Arthur J. III

    2000-01-01

    Experimental results are reported on a mobile, stand-alone, solar-blind ultraviolet (UV) Raman lidar system for the stand-off detection and identification of liquid and solid targets at ranges of hundreds of meters. The lidar is a coaxial system capable of performing range-resolved measurements of gases and aerosols, as well as solids and liquids. The transmitter is a flash lamp pumped 30 Hz Nd:YAG laser with quadrupled output at 266 nm. The receiver subsystem is comprised of a 40 cm Cassegrain telescope, a holographic UV edge filter for suppressing the elastic channel, a 0.46 m Czerny-Turner spectrometer, and a time gated intensified charge-coupled device (CCD) detector. The rejection of elastic light scattering by the edge filter is better than one part in 10 5 , while the transmittance 500 cm-1 to the red of the laser line is greater than 50%. Raman data are shown for selected solids, neat liquids, and mixtures down to the level of 1% volume ratio. On the basis of the strength of the Raman returns, a stand-off detection limit of ∼500 g/m2 for liquid spills of common solvents at the range of one half of a kilometer is possible. (c) 2000 Society for Applied Spectroscopy

  16. Heat driven thermoacoustic cooler based on traveling-standing wave

    International Nuclear Information System (INIS)

    Kang Huifang; Zhou Gang; Li Qing

    2010-01-01

    This paper presents a heat driven thermoacoustic cooler system without any moving part. It consists of a thermoacoustic engine and a thermoacoustic cooler, and the former is the driving source of the latter. Both the engine and the cooler are located in one loop tube coupled with a resonator tube, and the acoustic power produced by the engine is used to drive the cooler directly. Both regenerators of the engine and the cooler are located in the near region of the pressure antinode, and operate in traveling-standing wave phase region. In the engine's regenerator, both components of the standing wave and the traveling wave realize the conversion from heat to acoustic energy. This improves the efficiency of the engine. In the cooler's regenerator, both components of the traveling wave and the standing wave pump heat from the cold end. This improves the efficiency of the cooler. At the operating point with a mean pressure of 22 bar, helium as working gas, a frequency of 234 Hz, and a heating power of 300 W, the experimental cooler provides a no-load temperature of -30 deg. C and a cooling power of 40 W at the cooling temperature of 0 deg. C. The total length of this cooler system is less than 1 m, which shows a good prospect for the domestic cooler system in room-temperature cooling such as food refrigeration and air-conditioning.

  17. Predicted stand volume for Eucalyptus plantations by spatial analysis

    Science.gov (United States)

    Latifah, Siti; Teodoro, RV; Myrna, GC; Nathaniel, CB; Leonardo, M. F.

    2018-03-01

    The main objective of the present study was to assess nonlinear models generated by integrating the stand volume growth rate to estimate the growth and yield of Eucalyptus. The primary data was done for point of interest (POI) of permanent sample plots (PSPs) and inventory sample plots, in Aek Nauli sector, Simalungun regency,North Sumatera Province,Indonesia. from December 2008- March 2009. Today,the demand for forestry information has continued to grow over recent years. Because many forest managers and decision makers face complex decisions, reliable information has become the necessity. In the assessment of natural resources including plantation forests have been widely used geospatial technology.The yield of Eucalyptus plantations represented by merchantable volume as dependent variable while factors affecting yield namely stands variables and the geographic variables as independent variables. The majority of the areas in the study site has stand volume class 0 - 50 m3/ha with 16.59 ha or 65.85 % of the total study site.

  18. Analysis of Human Standing Balance by Largest Lyapunov Exponent

    Directory of Open Access Journals (Sweden)

    Kun Liu

    2015-01-01

    Full Text Available The purpose of this research is to analyse the relationship between nonlinear dynamic character and individuals’ standing balance by the largest Lyapunov exponent, which is regarded as a metric for assessing standing balance. According to previous study, the largest Lyapunov exponent from centre of pressure time series could not well quantify the human balance ability. In this research, two improvements were made. Firstly, an external stimulus was applied to feet in the form of continuous horizontal sinusoidal motion by a moving platform. Secondly, a multiaccelerometer subsystem was adopted. Twenty healthy volunteers participated in this experiment. A new metric, coordinated largest Lyapunov exponent was proposed, which reflected the relationship of body segments by integrating multidimensional largest Lyapunov exponent values. By using this metric in actual standing performance under sinusoidal stimulus, an obvious relationship between the new metric and the actual balance ability was found in the majority of the subjects. These results show that the sinusoidal stimulus can make human balance characteristics more obvious, which is beneficial to assess balance, and balance is determined by the ability of coordinating all body segments.

  19. Robot-supported assessment of balance in standing and walking.

    Science.gov (United States)

    Shirota, Camila; van Asseldonk, Edwin; Matjačić, Zlatko; Vallery, Heike; Barralon, Pierre; Maggioni, Serena; Buurke, Jaap H; Veneman, Jan F

    2017-08-14

    Clinically useful and efficient assessment of balance during standing and walking is especially challenging in patients with neurological disorders. However, rehabilitation robots could facilitate assessment procedures and improve their clinical value. We present a short overview of balance assessment in clinical practice and in posturography. Based on this overview, we evaluate the potential use of robotic tools for such assessment. The novelty and assumed main benefits of using robots for assessment are their ability to assess 'severely affected' patients by providing assistance-as-needed, as well as to provide consistent perturbations during standing and walking while measuring the patient's reactions. We provide a classification of robotic devices on three aspects relevant to their potential application for balance assessment: 1) how the device interacts with the body, 2) in what sense the device is mobile, and 3) on what surface the person stands or walks when using the device. As examples, nine types of robotic devices are described, classified and evaluated for their suitability for balance assessment. Two example cases of robotic assessments based on perturbations during walking are presented. We conclude that robotic devices are promising and can become useful and relevant tools for assessment of balance in patients with neurological disorders, both in research and in clinical use. Robotic assessment holds the promise to provide increasingly detailed assessment that allows to individually tailor rehabilitation training, which may eventually improve training effectiveness.

  20. Developing silvicultural systems based on partial cutting in western hemlock–Sitka spruce stands of southeast Alaska.

    Science.gov (United States)

    Robert L. Deal; J.C. Tappeiner; Paul E. Hennon

    2002-01-01

    The effects of partial cutting on species composition, stand structure and growth, tree size distribution, and tree disease and mortality were evaluated on 73 plots in 18 stands that were harvested 12–96 years ago in southeast Alaska. Partially-cut stands had diverse and highly complex stand structures similar to uncut stands. Sitka spruce was maintained in mixed...

  1. Reliability of system identification techniques to assess standing balance in healthy elderly

    NARCIS (Netherlands)

    Pasma, Jantsje H.; Engelhart, Denise; Maier, Andrea B.; Aarts, Ronald G.K.M.; Van Gerven, Joop M.A.; Arendzen, J. Hans; Schouten, Alfred C.; Meskers, Carel G.M.; Van Kooij, Herman Der

    2016-01-01

    Objectives System identification techniques have the potential to assess the contribution of the underlying systems involved in standing balance by applying well-known disturbances. We investigated the reliability of standing balance parameters obtained with multivariate closed loop system

  2. Reliability of System Identification Techniques to Assess Standing Balance in Healthy Elderly

    NARCIS (Netherlands)

    Pasma, J.H.; Engelhart, D.; Maier, A.B.; Aarts, R.G.K.M.; Van Gerven, J.M.A.; Arendzen, J.H.; Schouten, A.C.; Meskers, C.G.M.; Van der Kooij, H.

    2016-01-01

    Objectives System identification techniques have the potential to assess the contribution of the underlying systems involved in standing balance by applying well-known disturbances. We investigated the reliability of standing balance parameters obtained with multivariate closed loop system

  3. The risk of varicose veins in standing female workers

    Directory of Open Access Journals (Sweden)

    Tony Hidayat

    2013-07-01

    Full Text Available AbstrakLatar belakang:Varises sering terjadi pada karyawan yang harus bekerja dalam posisi kerja berdiri. Tujuan penelitian ini untuk mengetahui beberapa faktor risiko terhadap varises tungkai dan atau kaki di antara pekerja perempuan. Metode:Penelitian potong lintang ini dilakukan pada Januari-Maret 2010. Sampel penelitian yang dipilih secara purposif yang memenuhi kriteria inklusi penelitian di antara pekerja perempuan perlu bekerja dalam  posisi  kerja  berdiri.  Data  dikumpulkan  dengan  wawancara,  pemeriksaan  fisik  dan  observasi posisi kerja berdiri. Pengolahan data untuk menentukan faktor dominan terhadap varises menggunakan pendekatan risiko relatif.Hasil:Dari 152 karyawan yang terdapat 111 yang bersedia mengikuti penelitian, dan yang menderita varises tungkai dan atau kaki sebanyak 52,3% (53 orang. Sebagian besar responden berusia 18-35 tahun, memiliki masa kerja 3-17 tahun, bekerja dalam posisi kerja banyak berdiri. Sebagian kecil responden memiliki riwayat varises di dalam keluarga (13,51%, memakai kontrasepsi oral (11,71%, memiliki kebiasaan olah raga (18,02% dan memakai sepatu hak tinggi (11,71%. Faktor umur, pemakaian kontrasepsi oral, pemakaian sepatu hak tinggi, kebiasaan olah raga, posisi kerja berdiri, tempat kerja, dan masa kerja tidak berhubungan dengan varises tungkai dan atau kaki. Karyawan yang mempunyai dibandingkan dengan yang tidak mempunyai riwayat keluarga varises, berisiko 69% lebih tinggi menderita varises [risiko relatif (RR = 1,69; P = 0.121]. Kesimpulan:Karyawan yang mempunyai riwayat keluarga varises berisiko lebih tinggi menderita varises. (Health Science Indones 2013;1:47-50 Kata kunci:varises, posisi kerja berdiriAbstractBackground: Varicose veins often occur in employees who have to work in a position of standing work. The purpose of this study to determine risk factors for varicose veins and leg or foot among women workers.Methods: In this cross-sectional study in January-March 2010 the

  4. AORN Ergonomic Tool 4: Solutions for Prolonged Standing in Perioperative Settings.

    Science.gov (United States)

    Hughes, Nancy L; Nelson, Audrey; Matz, Mary W; Lloyd, John

    2011-06-01

    Prolonged standing during surgical procedures poses a high risk of causing musculoskeletal disorders, including back, leg, and foot pain, which can be chronic or acute in nature. Ergonomic Tool 4: Solutions for Prolonged Standing in Perioperative Settings provides recommendations for relieving the strain of prolonged standing, including the use of antifatigue mats, supportive footwear, and sit/stand stools, that are based on well-accepted ergonomic safety concepts, current research, and access to new and emerging technology. Published by Elsevier Inc.

  5. Using a standing-tree acoustic tool to identify forest stands for the production of mechanically-graded lumber.

    Science.gov (United States)

    Paradis, Normand; Auty, David; Carter, Peter; Achim, Alexis

    2013-03-12

    This study investigates how the use of a Hitman ST300 acoustic sensor can help identify the best forest stands to be used as supply sources for the production of Machine Stress-Rated (MSR) lumber. Using two piezoelectric sensors, the ST300 measures the velocity of a mechanical wave induced in a standing tree. Measurements were made on 333 black spruce (Picea mariana (Mill.) BSP) trees from the North Shore region, Quebec (Canada) selected across a range of locations and along a chronosequence of elapsed time since the last fire (TSF). Logs were cut from a subsample of 39 trees, and sawn into 77 pieces of 38 mm × 89 mm cross-section before undergoing mechanical testing according to ASTM standard D-4761. A linear regression model was developed to predict the static modulus of elasticity of lumber using tree acoustic velocity and stem diameter at 1.3 m above ground level (R2 = 0.41). Results suggest that, at a regional level, 92% of the black spruce trees meet the requirements of MSR grade 1650Fb-1.5E, whilst 64% and 34% meet the 2100Fb-1.8E and 2400Fb-2.0E, respectively. Mature stands with a TSF < 150 years had 11 and 18% more boards in the latter two categories, respectively, and therefore represented the best supply source for MSR lumber.

  6. Can't Stand the Pressure: The Association Between Unprotected Standing, Walking, and Wound Healing in People With Diabetes.

    Science.gov (United States)

    Najafi, Bijan; Grewal, Gurtej S; Bharara, Manish; Menzies, Robert; Talal, Talal K; Armstrong, David G

    2017-07-01

    The objective was to report patterns of physical activity and their relationship to wound healing success in patients with diabetic foot ulcers protected with removable or irremovable offloading devices. Forty-nine people with diabetic foot ulcers were randomized to wear either a removable cast walker (RCW) or an irremovable instant total contact cast (iTCC). Primary outcome measures included change in wound size, physical activities including position (ie, sitting, standing, lying) and locomotion (speed, steps, etc). Outcomes parameters were assessed on weekly basis until wound healing or until 12 weeks. A higher proportion of patients healed at 12 weeks in the iTCC group ( P = .038). Significant differences in activity were observed between groups starting at week 4. RCW patients became more active than the iTCC group (75% higher duration of standing, 100% longer duration of walking, and 126% longer unbroken walking bout, P healing and number of steps taken per day ( r healing ( r = -.67, P healing at 12 weeks. The results from this study suggest significant differences in activity patterns between removable and irremovable offloading devices. These patterns appear to start diverging at week 4, which may indicate a decline in adherence to offloading. Results suggest that while walking may delay wound healing, unprotected standing might be an even more unrealized and sinister culprit.

  7. The Control of Posture in Newly Standing Infants is Task Dependent

    Science.gov (United States)

    Claxton, Laura J.; Melzer, Dawn K.; Ryu, Joong Hyun; Haddad, Jeffrey M.

    2012-01-01

    The postural sway patterns of newly standing infants were compared under two conditions: standing while holding a toy and standing while not holding a toy. Infants exhibited a lower magnitude of postural sway and more complex sway patterns when holding the toy. These changes suggest that infants adapt postural sway in a manner that facilitates…

  8. Test of four stand growth simulators for the northeastern United States

    Science.gov (United States)

    Thomas M. Schuler; David A. Marquis; Richard L. Ernst; Brian T. Simpson; Brian T. Simpson

    1993-01-01

    Evaluates SILVAH, FIBER, NE-TWIGS, and OAKSIM, simulators commonly used in the northeastern United States, by comparing predicted stand development with actual stand development records for periods ranging from 15 to 50 years. Results varied with stand parameter, forest type, projection length, and geographic area. Except in the spruce-fir forest type where FIBER...

  9. Standing down Straight: Jump Rhythm Technique's Rhythm-Driven, Community-Directed Approach to Dance Education

    Science.gov (United States)

    Siegenfeld, Billy

    2009-01-01

    "Standing down straight" means to stand on two feet with both stability and relaxation. Using standing down straight as the foundation of class work, Jump Rhythm Technique offers a fresh alternative to conventional systems of dance study. It bases its pedagogy on three behaviors: grounding the body so that it can move with power and efficiency,…

  10. Simulation of growth and competition in mixed stands of Douglas-fir and beech

    NARCIS (Netherlands)

    Bartelink, H.H.

    1998-01-01

    For a long time, the emphasis in silviculture in Western Europe was solely on even-aged, monospecific stands; many empirical stand-level growth models were developed and successfully used for managing such stands. In contrast, no generally accepted growth and yield approach has emerged so

  11. Production economics of harvesting small-diameter hardwood stands in central Appalachia

    Science.gov (United States)

    Yaoxiang Li; Jingxin Wang; Gary Miller; Joe McNeel

    2006-01-01

    Three harvesting systems of chainsaw/cable skidder, feller-buncher/grapple skidder, and harvester/forwarder were simulated in harvesting three hardwood stands 30 to 50 years old in central Appalachia. Stands were generated by using a 3D stand generator. Harvesting prescriptions included clearcut, shelterwood cut, selective cut, diameter limit cut, and crop tree release...

  12. Early development of postural adjustments in standing with and without support

    NARCIS (Netherlands)

    Hedberg, Asa; Schmitz, Christina; Forssberg, Hans; Hadders-Algra, Mijna

    This study investigates the early development of postural adjustments during external perturbations in two different standing positions: standing with support and standing without support. The aim of the study was to assess a group of 13 infants four times during the period in life when independent

  13. Age-Related Differences in Quality of Standing Balance Using a Composite Score

    NARCIS (Netherlands)

    Pasma, J.H.; Bijlsma, A.Y.; van der Bij, M.D.W.; Arendzen, J.H.; Meskers, C.G.M.; Maier, A.B.

    2014-01-01

    Background: Age-related differences in standing balance are not detected by testing the ability to maintain balance. Quality of standing balance might be more sensitive to detect age-related differences. Objective: To study age-related differences in quality of standing balance, center of pressure

  14. Basal area or stocking percent: which works best in controlling density in natural shortleaf pine stands

    Science.gov (United States)

    Ivan L. Sander

    1986-01-01

    Results from a shortleaf pine thinning study in Missouri show that continually thinning a stand to the same basal area will eventually create an understocked stand and reduce yields. Using stocking percent to control thinning intensity allows basal area to increase as stands get older. The best yield should occur when shortleaf pine is repeatedly thinned to 60 percent...

  15. Effects of intermediate-severity disturbance on composition and structure in mixed Pinus-hardwood stands

    Science.gov (United States)

    Benjamin Trammell; Justin Hart; Callie Schweitzer; Daniel C. Dey; Michael Steinberg

    2017-01-01

    Increasingly, forest managers intend to create or maintain mixed Pinus-hardwood stands. This stand assemblage may be driven by a variety of objectives but is often motivated by the desire to enhance native forest diversity and promote resilience to perturbations. Documenting the effects of natural disturbances on species composition and stand...

  16. Comparison of three sampling methods in the characterization of cork oak stands for management purpose

    NARCIS (Netherlands)

    Paulo, M.J.; Tomé, M.; Otten, A.; Stein, A.

    2005-01-01

    The cork oak (Quercus suber L.) is an evergreen oak that has the ability to produce a continuous layer of cork tissue which regenerates after being removed. Cork oak stands can be diverse in structure. Young stands are often regularly spaced, whereas older stands usually show clustering and can be

  17. NDE of logs and standing trees using new acoustic tools : technical application and results

    Science.gov (United States)

    Peter Carter; Xiping Wang; Robert J. Ross; David Briggs

    2005-01-01

    The new Director ST300 provides a means to efficiently assess stands for stiffness and related wood properties based on standing tree acoustic velocily measures, and can be easily integrated with pre-harvest and earlier stand assessments. This provides for effective valuation for forest sale, stumpage purchase, harvest planning, and ranking of progeny or clones in tree...

  18. Standing sedation in captive zebra (Equus grevyi and Equus burchellii).

    Science.gov (United States)

    Hoyer, Mark; de Jong, Sara; Verstappen, Frank; Wolters, Marno

    2012-03-01

    Nine Grevy's zebras (Equus grevyi) and three Burchell's zebras (Equus burchellii) were immobilized in a standing position a total of 70 times for minor, nonpainful procedures over a 9-yr period. Standing sedation was successfully obtained with a combination of detomidine and butorphanol on 47 occasions (67.1%). Detomidine i.m. (median 0.10 mg/kg; range: 0.07-0.21) was administered by dart, followed 10 min later by butorphanol i.m. (median 0.13 mg/kg; range 0.04-0.24). The dosages were varied depending on the initial demeanor of the animal. On 23 occasions (32.9%), small amounts of etorphine (median 2.5 microg/kg; range 1.1-12.3 microg/kg) plus acepromazine (median 10 microg/kg; range 4.4-50 microg/kg) (as in Large Animal-Immobilon) had to be administered i.m. to gain sufficient sedation. In these latter cases, the animals were either excited or known for their aggressive character. The zebras were sufficiently immobilized for the length of most procedures (<45 min) without supplementation. At the end of the procedure, the animals were given atipamezole (2 mg per 1 mg detomidine used) and naltrexone (0.1 mg/kg) to reverse the sedative effects, irrespective of whether etorphine was used or not. Standing sedation, using the combination of the alpha-2 agonist detomidine and the partial agonist-antagonist opioid butorphanol (in some cases supplemented with etorphine + acepromazine), proved to be a very efficacious and safe method to be used in zebras under zoo conditions for short-lasting, nonpainful procedures.

  19. Improvement of Stand Jig Sealer and Its Increased Production Capacity

    Science.gov (United States)

    Soebandrija, K. E. N.; Astuti, S. W. D.

    2014-03-01

    This paper has the objective to prove that improvement of Stand Jig Sealer can lead to the cycle time target as part of Improvement efforts and its Productivity. Prior researches through prior journals both classics journal such as Quesnay (1766) and Solow (1957) and updated journal such as Reikard (2011) researches, are mentioned and elaborated. Precisely, the research is narrowed down and specified into automotive industry and eventually the software related of SPSS and Structural Equation Modeling ( SEM ). The analysis and its method are conducted through the calculation working time. The mentioned calculation are reinforced with the hypothesis test using SPSS Version 19 and involve parameters of production efficiency, productivity calculation, and the calculation of financial investments. The results obtained are augmented achievement of cycle time target ≤ 80 seconds posterior to improvement stand jig sealer. The result from calculation of SPSS-19 version comprise the following aspects: the one-sided hypothesis test is rejection of Ho:μ≥80 seconds, the correlation rs=0.84, regression y = 0.159+0.642x, validity R table = 0.4438, reliability value of Cronbach's alpha = 0.885>0.70, independence (Chi Square) Asymp. Sig=0.028financial analysis (NPV 2,340,596>0, PI 2.04>1, IRR 45.56%>i=12.68%, PP=1.86). The Mentioned calculation results support the hypothesis and ultimately align with the objective of this paper to prove that improvement of Stand Jig Sealer and its relation toward the cycle time target. Precisely, the improvement of production capacity of PT. Astra Daihatsu Motor.

  20. Phenology and abundance of Enoicyla pusilla in conifer stands

    Directory of Open Access Journals (Sweden)

    M. J. Lombardero

    2013-07-01

    Full Text Available Aim of Study. We study the abundance of Enoicyla pusilla (Burmeister in pine plantations and the effects of silvicultural thinning on insect population. This species is considered a rare member of the order Trichoptera, reported as absent or occasional in conifer forests. It has been suggested that the proliferation of conifer plantations may be a threat for this species by favoring population isolation. Area of study. Plantations of native and non-native pines in Galicia (NW of Spain.Material and Methods. We used different traps systems, including 28 pitfall traps, to compared populations of insects in 14 thinned and unthinned plots of Pinus pinaster and P. radiata distributed across 3 forest stands. Traps were checked every 15 days during one year.Main results.  We caught 1.219 larvae of E. pusilla. It was the third most abundant species captured in pitfall traps. Larval activity extended from January to late July. They were more abundant in the stands of P. radiata, probably because the denser foliage produced limits sunlight and helped to maintain litter moisture. Additionally needles of P. radiata had lower toughness and higher nitrogen content, which probably makes it a higher quality resource for the detritivorous larvae. Thinning did not affect larvae population.Research highlights: Although managed forests cannot match the biodiversity value of native mixed species stands, if managed appropriately, they may provide habitat for native fauna while also allowing for forest productionKey words: caddisfly; Pinus pinaster; Pinus radiate; plantations; thinning.

  1. Analysis of the Heterogeneity of Weed Infestation in Cereal Stands

    Directory of Open Access Journals (Sweden)

    Jan Winkler

    2015-01-01

    Full Text Available The aim of this study was to evaluate the heterogeneity of the incidence of individual weed species on a selected experimental field. This field was situated in the cadastre of the village Žabčice (South Moravian Region, Czech Republic. To evaluate the intensity of weed infestation, a field experiment was established. In 2011, altogether 33 weed species were identified in a stand of spring barley. In the next year, the total number of weeds in a stand of winter wheat was 22. Basing on results of the evaluation of infestation heterogeneity it was possible to detect the following trends: The first one concerned the incidence of significantly dominant species Chenopodium album and Veronica hederifolia in stands of spring barley and winter wheat, respectively. The second one expressed the incidence of the so-called sub-dominant species. Regarding the character of the incidence of these weed species it would be suitable to kill them by means of a targeted application of herbicides. Finally, the third trend concerned the incidence of that group of weeds that occurred in the major part of the experimental plot but in low numbers only. The abundance of these species was minimal and the total number of weed plants did not exceed the limit of 100 specimens. This group of weeds involved also those species that were markedly more frequent on plots situated closer to the margin of the experimental field. The targeted application of herbicides can be performed on plots with a lower level of weed infestation; another possibility, however, seems to be a targeted intervention that helps to control the incidence of a certain weed species and/or that is performed along the margin of the field where the different weed species are more frequent.

  2. Standing Classrooms: Research and Lessons Learned from Around the World.

    Science.gov (United States)

    Hinckson, Erica; Salmon, Jo; Benden, Mark; Clemes, Stacey A; Sudholz, Bronwyn; Barber, Sally E; Aminian, Saeideh; Ridgers, Nicola D

    2016-07-01

    Children spend between 50 and 70 % of their time sitting while at school. Independent of physical activity levels, prolonged sitting is associated with poor health outcomes in adulthood. While there is mixed evidence of health associations among children and adolescents, public health guidelines in the USA, UK, Australia and Canada now recommend young people should break up long periods of sitting as frequently as possible. A potentially effective approach for reducing and breaking up sitting throughout the day is changing the classroom environment. This paper presents an overview of a relatively new area of research designed to reduce youth sitting time while at school by changing the classroom environment (n = 13 studies). Environmental changes included placement of height-adjustable or stand-biased standing desks/workstations with stools, chairs, exercise balls, bean bags or mats in the classroom. These 13 published studies suggest that irrespective of the approach, youth sitting time was reduced by between ~44 and 60 min/day and standing time was increased by between 18 and 55 min/day during classroom time at school. Other benefits include increased energy expenditure and the potential for improved management of students' behaviour in the classroom. However, few large trials have been conducted, and there remains little evidence regarding the impact on children's learning and academic achievement. Nevertheless, with an increasing demand placed on schools and teachers regarding students' learning outcomes, strategies that integrate moving throughout the school day and that potentially enhance the learning experience and future health outcomes for young people warrant further exploration.

  3. OPTIMIZATION OF HEMISPHERICAL RESONATOR GYROSCOPE STANDING WAVE PARAMETERS

    Directory of Open Access Journals (Sweden)

    Olga Sergeevna Khalyutina

    2017-01-01

    Full Text Available Traditionally, the problem of autonomous navigation is solved by dead reckoning navigation flight parameters (NFP of the aircraft (AC. With increasing requirements to accuracy of definition NFP improved the sensors of the prima- ry navigation information: gyroscopes and accelerometers. the gyroscopes of a new type, the so-called solid-state wave gyroscopes (SSVG are currently developed and put into practice. The work deals with the problem of increasing the accu- racy of measurements of angular velocity of the hemispherical resonator gyroscope (HRG. The reduction in the accuracy characteristics of HRG is caused by the presence of defects in the distribution of mass in the volume of its design. The syn- thesis of control system for optimal damping of the distortion parameters of the standing wave due to the influence of the mass defect resonator is adapted. The research challenge was: to examine and analytically offset the impact of the standing wave (amplitude and frequency parameters defect. Research was performed by mathematical modeling in the environment of SolidWorks Simulation for the case when the characteristics of the sensitive element of the HRG met the technological drawings of a particular type of resonator. The method of the inverse dynamics was chosen for synthesis. The research re- sults are presented in graphs the amplitude-frequency characteristics (AFC of the resonator output signal. Simulation was performed for the cases: the perfect distribution of weight; the presence of the mass defect; the presence of the mass defects are shown using the synthesized control action. Evaluating the effectiveness of the proposed control algorithm is deter- mined by the results of the resonator output signal simulation provided the perfect constructive and its performance in the presence of a mass defect in it. It is assumed that the excitation signals are standing waves in the two cases are identical in both amplitude and frequency. In this

  4. Cellular composition of long-standing gingivitis and periodontitis lesions.

    Science.gov (United States)

    Thorbert-Mros, S; Larsson, L; Berglundh, T

    2015-08-01

    Insufficient information on the cellular composition of long-standing gingivitis lesions without signs of attachment loss makes an understanding of differences in cellular composition between "destructive" and "nondestructive" periodontal lesions difficult. The aim of the current study was to analyze differences in cell characteristics between lesions representing long-standing gingivitis and severe periodontitis. Two groups of patients were recruited. One group consisted of 36 patients, 33-67 years of age, with severe generalized periodontitis (periodontitis group). The second group consisted of 28 patients, 41-70 years of age, with overt signs of gingival inflammation but no attachment loss (gingivitis group). From each patient a gingival biopsy was obtained from one selected diseased site and prepared for immunohistochemical analysis. Periodontitis lesions were twice as large and contained significantly larger proportions, numbers and densities of cells positive for CD138 (plasma cells) and CD68 (macrophages) than did gingivitis lesions. The proportion of B cells that expressed the additional CD5 marker (B-1a cells) was significantly larger in periodontitis lesions than in gingivitis lesions. The densities of T cells and B cells did not differ between periodontitis lesions and gingivitis lesions. T cells were not the dominating cell type in gingivitis lesions, as B cells together with their subset plasma cells comprised a larger number and proportion than T cells. Periodontitis lesions at teeth with advanced attachment and bone loss exhibit quantitative and qualitative differences in relation to gingivitis lesions at teeth with no attachment and bone loss. It is suggested that the large number and high density of plasma cells are the hallmarks of advanced periodontitis lesions and the most conspicuous difference in relation to long-standing gingivitis lesions. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  5. Models for a stand-alone PV system[Photovoltaic

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, A.D.; Soerensen, P.; Hansen, L.H.; Bindner, H.

    2000-12-01

    This report presents a number of models for modelling and simulation of a stand-alone photovoltaic (PV) system with a battery bank verified against a system installed at Risoe National Laboratory. The work has been supported by the Danish Ministry of Energy, as a part of the activities in the Solar Energy Centre Denmark. The study is carried out at Risoe National Laboratory with the main purpose to establish a library of simple mathematical models for each individual element of a stand-alone PV system, namely solar cells, battery, controller, inverter and load. The models for PV module and battery are based on the model descriptions found in the literature. The battery model is developed at UMASS and is known as the Kinetic Battery Model (KiBaM). The other component models in the PV system are based on simple electrical knowledge. The implementation is done using Matlab/Simulink, a simulation program that provides a graphical interface for building models as modular block diagrams. The non-linear behaviour of the battery, observed in the measurements, is investigated and compared to the KiBaM model's performance. A set of linear Black box models are estimated based on the battery measurements. The performance of the best linear Black box model is compared to the KiBaM model. A validation of each of the implemented mathematical model is performed by an interactive analysis and comparison between simulation results and measurements, acquired from the stand-alone PV system at Risoe. (au)

  6. Size-Prediction Analysis for Stand-Alone Photovoltaic System

    International Nuclear Information System (INIS)

    Erusiafe, N. E.; Chendo, M. A. C.

    2002-01-01

    The cost - effectiveness of photovoltaic (PV) generator depends, among others, on its ability to satisfy energy demand and the cost of achieving this. In this work a step - by - step procedure for predicting the size of the main components of a stand - alone PV system (array and storage) is presented. The results yield an expression which can he used lo determine the size of both components at optimum cost and desired reliability. The result from this work compare favourably with some earlier works in that, the system sizes shows some degree of agreement

  7. Availability model of stand-alone photovoltaic system

    Science.gov (United States)

    Mazurek, G.

    2017-08-01

    In this paper we present a simple, empirical model of stand-alone photovoltaic power system availability. The model is a final result of five-year long studies and ground measurements of solar irradiation carried out in Central Europe. The obtained results facilitate sizing of PV modules that have to be installed with taking into account system's availability level in each month of a year. The model can be extended to different geographical locations, with help of local meteorological data or solar irradiation datasets derived from satellite measurements.

  8. Radiation measurements during cavities conditioning on APS RF test stand

    International Nuclear Information System (INIS)

    Grudzien, D.M.; Kustom, R.L.; Moe, H.J.; Song, J.J.

    1993-01-01

    In order to determine the shielding structure around the Advanced Photon Source (APS) synchrotron and storage ring RF stations, the X-ray radiation has been measured in the near field and far field regions of the RF cavities during the normal conditioning process. Two cavity types, a prototype 352-MHz single-cell cavity and a 352-MHz five-cell cavity, are used on the APS and are conditioned in the RF test stand. Vacuum measurements are also taken on a prototype 352-MHz single-cell cavity and a 352-MHz five-cell cavity. The data will be compared with data on the five-cell cavities from CERN

  9. Future UK markets for stand-alone renewable energy systems

    International Nuclear Information System (INIS)

    Paish, O.

    1999-01-01

    A study to identify and quantify the market for stand-alone renewable energy supplies of power (photovoltaics, wind and micro-hydro electricity systems) was described. The study focused on small systems, generally less than a few kW installed capacity. It was suggested that in the UK, the emphasis on grid-connected renewable energy technologies (RETs) has blurred the fact that it is 'off-grid' renewable systems that can offer more immediate real commercial markets for the renewables business. With the likelihood of a significant increase in demand for renewables world wide over the next ten years, the UK needs to make a special effort to become involved

  10. Vibration transmission characteristics of the legs of freely standing honeybees

    DEFF Research Database (Denmark)

    Rohrseitz, Kristin; Kilpinen, Ole

    1997-01-01

    as the stimulator. This was also the case in freely standing honeybees, except around 400 Hz, where an average attenuation of approximately 6 dB was observed. In the fixed bee preparation, the vertical movements of the legs were also measured during horizontal stimulation. The vertical vibration amplitude...... of the legs was 15-20 dB lower than the horizontal stimulation amplitude. The electrophysiologically and behaviourally determined thresholds for vibration stimulation increased by approximately 10 dB, when the stimulus direction was changed from vertical to horizontal. These observations support the notion...

  11. 2014 Behavioral Health and Performance Standing Review Panel

    Science.gov (United States)

    Steinberg, Susan; Leon, Gloria; Dimsdale, Joel; Balkin, Thomas; Bono, Joyce; Caldwell, John; Joiner, Thomas; Paulus, Martin; Zaccaro, Stephen

    2015-01-01

    The 2014 Behavioral Health and Performance (BHP) Standing Review Panel (from here on referred to as the SRP) met for a site visit in Houston, TX on December 17 - 18, 2014. The SRP reviewed the updated research plan for the Risk of Performance Errors Due to Fatigue Resulting from Sleep Loss, Circadian Desynchronization, Extended Wakefulness, and Work Overload (Sleep Risk) and also received a status update on the Risk of Adverse Behavioral Conditions and Psychiatric Disorders (BMed Risk) and the Risk of Performance Decrements Due to Inadequate Cooperation, Coordination, Communication, and Psychosocial Adaptation within a Team (Team Risk).

  12. UV radiation emitted by selected sources at work stands

    International Nuclear Information System (INIS)

    Kozlowski, C.

    2001-01-01

    The paper presents the results of UV effective irradiance measurements at work stands for sources such as: welding arcs, gas blowpipes, exposure processes, printing machines and insecticide lamps. The irradiance measurements were performed using broad-band instruments with detector heads corrected to the Polish action spectra (erythematous and conjunctivitis). The obtained values of effective irradiance for above sources ranged from 0.2 to 8000 mW/m2. Safe exposure time corresponding to irradiance was calculated for the Polish threshold limit values. For welding processes the spectra of selected welding arcs are presented additionally. These spectra were measured using a fiber-optic spectrometer. (author)

  13. Benchmarking the Collocation Stand-Alone Library and Toolkit (CSALT)

    Science.gov (United States)

    Hughes, Steven; Knittel, Jeremy; Shoan, Wendy; Kim, Youngkwang; Conway, Claire; Conway, Darrel J.

    2017-01-01

    This paper describes the processes and results of Verification and Validation (VV) efforts for the Collocation Stand Alone Library and Toolkit (CSALT). We describe the test program and environments, the tools used for independent test data, and comparison results. The VV effort employs classical problems with known analytic solutions, solutions from other available software tools, and comparisons to benchmarking data available in the public literature. Presenting all test results are beyond the scope of a single paper. Here we present high-level test results for a broad range of problems, and detailed comparisons for selected problems.

  14. Modelling and Experiments of a Standing Wave Piezomotor

    DEFF Research Database (Denmark)

    Andersen, B.; Helbo, Jan; Blanke, Mogens

    The paper presents a new contact model for standing wave piezomotors. The contact model is based on the Hertz theory for normal contact deformations and elastic contact theory for tangential loads. The contact theory is simplified into a model with discrete springs for normal and tangential loads...... which allows the calculation of slip/stick transitions. Simulations show that tip trajectories in general cannot be prescribed. The paper presents the principle of a bending resonator. Experiments indicate that the bending vibrations are too small to generate rotor rotations. However, due to unintended...

  15. Modelling and Experiments of a Standing Wave Piezomotor

    DEFF Research Database (Denmark)

    Helbo, Jan; Andersen, Brian; Blanke, Mogens

    2002-01-01

    The paper presents a new contact model for standing wave piezomotors. The contact model is based on the Hertz theory for normal contact deformations and elastic contact theory for tangential loads. The contact theory is simplified into a model with discrete springs for normal and tangential loads...... which allows the calculation of slip/stick transitions. Simulations show that tip trajectories in general cannot be prescribed. The paper presents the principle of a bending resonator. Experiments indicate that the bending vibrations are too small to generate rotor rotations. However, due to unintended...

  16. Cryogenic System for the Cryomodule Test Stand at Fermilab

    Energy Technology Data Exchange (ETDEWEB)

    White, Michael J. [Fermilab; Hansen, Benjamin [Fermilab; Klebaner, Arkadiy [Fermilab

    2017-10-09

    This paper describes the cryogenic system for the Cryomodule Test Stand (CMTS) at the new Cryomodule Test Facility (CMTF) located at Fermilab. CMTS is designed for production testing of the 1.3 GHz and 3.9GHz cryomodules to be used in the Linac Coherent Light Source II (LCLSII), which is an upgrade to an existing accelerator at Stanford Linear Accelerator Laboratory (SLAC). This paper will focus on the cryogenic system that extends from the helium refrigeration plant to the CMTS cave. Topics covered will include component design, installation and commissioning progress, and operational plans. The paper will conclude with a description of the heat load measurement plan.

  17. Two anomalous cardiovascular responses to active standing in essential hypertension.

    Science.gov (United States)

    Bettencourt, M Joaquina; Pinto, Basílio Gomes; de Oliveira, E Infante; Silva-Carvalho, L

    2008-05-01

    In a previous work we studied, non-invasively, autonomic nervous system control of circulation in healthy subjects, observing the hemodynamic reaction to active standing. We now propose to extend this analysis to essential hypertension (EH), investigating possible autonomic dysfunction. The cardiovascular response to postural change from the supine position to active standing of 48 EH patients, of both sexes, with and without medication, was compared with that obtained for healthy subjects. We evaluated arterial systolic (SBP) and diastolic (DBP) blood pressure, stroke volume (SV), inotropic index (INOI), total vascular resistance (TVR), cardiac work (W), stroke work (SW), arterial compliance (AC) and heart rate (HR), using the entirely non-invasive BoMed NCCOM3 thoracic electrical bioimpedance monitor and sphygmomanometry. We found two patient groups characterized by different linear relationships between values of cardiovascular variables in active standing and in supine positions. Except for HR, in both groups these regression lines differed from normal. Compared to the supine position, in active standing, one group (EH-I) presented increased TVR, diminished SV, INOI, W, SW, and AC, and normal HR; the other group (EH-II) presented diminished TVR and HR and increased SV, INOI, W, SW and AC. The two patient groups could be separated on the basis of their age, but not on the basis of their systolic, diastolic and mean arterial blood pressures, gender or medication. The younger patient group (EH-I) included 28 subjects aged 24 to 69 years (50+/-10), of whom 11 were unmedicated, and the older patient group (EH-II) included 20 subjects aged 35 to 75 years (62+/-11), of whom 7 were unmedicated. Our results show a depressed response in postural change for older patients, which in the autonomic control of circulation expresses carotid baroreflex impairment, and conversely an enhanced response for younger patients, which can be caused by a maladjustment of the influence

  18. Enhanced current and voltage regulators for stand-alone applications

    DEFF Research Database (Denmark)

    Federico, de Bosio; Pastorelli, Michele; Antonio DeSouza Ribeiro, Luiz

    2016-01-01

    State feedback decoupling permits to achieve a better dynamic response for Voltage Source in stand-alone applications. The design of current and voltage regulators is performed in the discrete-time domain since it provides better accuracy and allows direct pole placement. As the attainable...... bandwidth of the current loop is mainly limited by computational and PWM delays, a lead compensator structure is proposed to overcome this limitation. The design of the voltage regulator is based on the Nyquist criterion, verifying to guarantee a high sensitivity peak. Discrete-time domain implementation...

  19. Do sit-to-stand performance changes during gait acquisition?

    OpenAIRE

    Bastos, Alana Maria Ferreira Guimarães; Costa, Carolina Souza Neves da; Rocha, Nelci Adriana Cicuto Ferreira

    2014-01-01

    In a child's daily routine, sit-to-stand (STS) is a prerequisite activity for many functional tasks. The relationship between gait and other abilities has been pointed out by many authors, but there is no study investigating the changes in STS during gait acquisition in children. The purpose of this study was to analyse, in healthy children, changes that occur in STS performance during gait acquisition. Five healthy children were initially assessed with an average age of 13.6 months. The kine...

  20. Ginástica rítmica – análise dos fatores competitivos motivadores e estressantes da Seleção Brasileira Juvenil =Rhythmical gymnastics – analysis of competitive, motivating and stress factors of the teenager Brazilian National Football Team

    Directory of Open Access Journals (Sweden)

    Lenamar Fiorese Vieira

    2005-07-01

    Full Text Available Este estudo objetivou investigar a trajetória de desenvolvimento das atletas de ginástica rítmica da Seleção Brasileira Juvenil, com foco na identificação dos fatores competitivos (motivadores e estressantes que ocorrem em diferentes fases da carreira esportiva. A população alvo foi de dez atletas. Como instrumentos de medida foramutilizados o Teste de Carga Psíquica de Frester e entrevista semi-estruturada. Para análise utilizou-se estatística descritiva e a análise de conteúdo do tipo categorial. Os resultados demonstraram que na ginástica rítmica o processo de especialização motora das atletas inicia aos 12 anos; os fatores motivadores evidenciados foram o gosto pelo esporte e ser o favorito; os fatores estressantes foram ser prejudicado pelos juizes e falta de tempo para divertimento.Concluindo em uma análise geral, as atletas perceberam o contexto esportivo competitivo como mais estressante do que motivador; esta afirmação acentuou-se a partir da fase de prática motora em que o estresse competitivo para o rendimento se intensificou.This study aimed to investigate the developmental trajectory of the Brazilian Rhythmic Gymnastics Youth Team, focusing on the identification of competitive factors (motivator and stressful thatoccurs in different sport’s career phases. The sample was composed ten athletes. As measure instruments were used the Frester’s Test Psychic Load and a semi-structured interview. The data were analyzed through the descriptive statistics and categorical type of content’s analysis. The results demonstrated that in the rhythmic gymnastics the process of the athletes’ motor specialization begins at 12 years; the motivator factors evidenced were fun for sport and being the favorite; the stressful factors were being harmed by the judges and not time for fun. Concluding in a general analysis the athletes perceived the competitive sporting context as more stressful than motivator; this affirmation

  1. Natural regeneration of trees in three types of afforested stands in the Taihang Mountains, China.

    Directory of Open Access Journals (Sweden)

    Xitian Yang

    Full Text Available Natural regeneration is the natural process by which plants replace themselves. It is a cost-effective way to re-establish vegetation, and it helps to preserve genetic identity and diversity. In this study, we investigated the natural regeneration of trees in three types of afforested stands in the Taihang Mountains, China, which were dominated by Robinia pseudoacacia (black locust, Quercus variabilis (Chinese cork oak and Platycladus orientalis (Chinese arborvitae respectively. A consistent pattern was found among the three types of stands, being that the density of seedlings was positively correlated with the overstory canopy cover and negatively correlated with the covers of shrub, herb and litter layers. While a positive correlation between the density of seedlings and stand age was found for the conifer stands, negative correlations were found for the two types of broadleaf stands. Correlations between the density of saplings and the stand attributes were not consistent among the three types of stands. The two types of broadleaf stands had higher densities of seedlings and saplings than the conifer stands. While the broadleaf stands had adequate recruits for regeneration, the conifer stands did not have enough recruits. Our findings suggest that the overstory canopy should be prevented from being disturbed, any reduction of the canopy cover will decrease the recruits and affect the regeneration.

  2. Transmittance of young Norway spruce stand canopy for photosynthetically active radiation during the growing season

    International Nuclear Information System (INIS)

    Markova, I.; Kubasek, J.

    2013-01-01

    Analysis of transmittance of young Norway spruce stand canopy for photosynthetically active radiation (PAR) was made at the study site of Bily Kriz (the Moravian-Silesian Beskids Mts., the Czech Republic) at different sky conditions during the growing season in 2010. For the description of PAR transmittance different phenological phases of the spruce stand development in clear and overcast days were chosen. The mean daily PAR transmittance of the spruce canopy was significantly higher in overcast days compared with clear ones. Diffuse PAR thus penetrated into lower parts of the canopy more efficiently than direct one. PAR transmittance of young Norway spruce stand canopy was different in individual phenological phases of the spruce stand canopy which was caused by changes in the stand structure during the growing season. Thus monitoring of transmittance of young Norway spruce stand canopy for PAR can help to describe the development of spruce stand canopy

  3. The effectiveness of sit-stand workstations for changing office workers' sitting time: results from the Stand@Work randomized controlled trial pilot

    NARCIS (Netherlands)

    Chau, J.Y.; Daley, M.; Dunn, S.; Srinivasan, A.; Do, A.; Bauman, A.E.; van der Ploeg, H.P.

    2014-01-01

    Prolonged sitting time is detrimental for health. Individuals with desk-based occupations tend to sit a great deal and sit-stand workstations have been identified as a potential strategy to reduce sitting time. Hence, the objective of the current study was to examine the effects of using sit-stand

  4. Planned Experiments on the Princeton Advanced Test Stand

    Science.gov (United States)

    Stepanov, A.; Gilson, E. P.; Grisham, L.; Kaganovich, I.; Davidson, R. C.

    2010-11-01

    The Princeton Advanced Test Stand (PATS) device is an experimental facility based on the STS-100 high voltage test stand transferred from LBNL. It consists of a multicusp RF ion source, a pulsed extraction system capable of forming high-perveance 100keV ion beams, and a large six-foot-long vacuum with convenient access for beam diagnostics. This results in a flexible system for studying high perveance ion beams relevant to NDCX-I/II, including experiments on beam neutralization by ferroelectric plasma sources (FEPS) being developed at PPPL. Research on PATS will concern the basic physics of beam-plasma interactions, such as the effects of volume neutralization on beam emittance, as well as optimizing technology of the FEPS. PATS combines the advantage of an ion beam source and a large-volume plasma source in a chamber with ample access for diagnostics, resulting in a robust setup for investigating and improving relevant aspects of neutralized drift. There are also plans for running the ion source with strongly electro-negative gases such as chlorine, making it possible to extract positive or negative ion beams.

  5. Key processes at the stand to landscape scale

    International Nuclear Information System (INIS)

    Perry, D.A.

    1991-01-01

    The smooth transition from one mature community type to another during climate change depends on the rate of climate change, the speed of migration, and the stability of extant communities as they become increasingly maladapted to local climates. The expected increase in natural disturbances will probably be the most important factor influencing forests over the next century, and has the potential to convert many forests to early successional, perhaps weedy vegetation. Protecting key structures and processes at both the stand and landscape scale will be critically important to easing the transition from one mature forest type to another and preventing site capture by weeds. Two general steps are necessary at the landscape scale: maintain migration corridors, and promote landscape patterns that dampen, rather than magnify, the spread of disturbances. At the stand level, it will be important to protect photosynthetic capacity and soil fertility. Steps to accomplish these goals include: protection of habitats required by natural enemies of forest pests; maintenance or restoration of natural biological diversity; maintenance or restoration of individual tree vigor through practices such as aggressive thinning; and moving from clearcutting to shelterwoods and/or group selections, thereby keeping some cover of mature green trees on sites at all times. 28 refs

  6. Thrust stand for vertically oriented electric propulsion performance evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Moeller, Trevor [University of Tennessee Space Institute, Tullahoma, Tennessee 37388 (United States); Polzin, Kurt A. [NASA, Marshall Space Flight Center, Huntsville, Alabama 35812 (United States)

    2010-11-15

    A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A noncontact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy-current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN level thrusts, while those tests conducted on a 200 lbm thruster yielded a resolution of roughly 2.5 mN at thrust levels of 0.5 N and greater.

  7. Acute alcohol intoxication impairs segmental body alignment in upright standing.

    Science.gov (United States)

    Hafstrom, A; Patel, M; Modig, F; Magnusson, M; Fransson, P A

    2014-01-01

    Balance control when standing upright is a complex process requiring input from several partly independent mechanisms such as coordination, feedback and feedforward control, and adaptation. Acute alcohol intoxication from ethanol is recognized as a major contributor to accidental falls requiring medical care. This study aimed to investigate if intoxication at 0.06 and 0.10% blood alcohol concentration affected body alignment. Mean angular positions of the head, shoulder, hip, and knee were measured with 3D-motion analysis and compared with the ankle position in 25 healthy adults during standing with or without perturbations, and with eyes open or closed. Alcohol intoxication had significant effects on body alignment during perturbed and unperturbed stance, and on adaptation to perturbations. It induced a significantly more posterior alignment of the knees and shoulders, and a tendency for a more posterior and left deviated head alignment in perturbed stance than when sober. The impact of alcohol intoxication was most apparent on the knee alignment, where availability of visual information deteriorated the adaptation to perturbations. Thus, acute alcohol intoxication resulted in inadequate balance control strategies with increased postural rigidity and impaired adaptation to perturbations. These factors probably contribute to the increased risk of falling when intoxicated with alcohol.

  8. Exchange anisotropy pinning of a standing spin-wave mode

    Science.gov (United States)

    Magaraggia, R.; Kennewell, K.; Kostylev, M.; Stamps, R. L.; Ali, M.; Greig, D.; Hickey, B. J.; Marrows, C. H.

    2011-02-01

    Standing spin waves in a thin film are used as sensitive probes of interface pinning induced by an antiferromagnet through exchange anisotropy. Using coplanar waveguide ferromagnetic resonance, pinning of the lowest energy spin-wave thickness mode in Ni80Fe20/Ir25Mn75 exchange-biased bilayers was studied for a range of Ir25Mn75 thicknesses. We show that pinning of the standing mode can be used to amplify, relative to the fundamental resonance, frequency shifts associated with exchange bias. The shifts provide a unique “fingerprint” of the exchange bias and can be interpreted in terms of an effective ferromagnetic film thickness and ferromagnet-antiferromagnet interface anisotropy. Thermal effects are studied for ultrathin antiferromagnetic Ir25Mn75 thicknesses, and the onset of bias is correlated with changes in the pinning fields. The pinning strength magnitude is found to grow with cooling of the sample, while the effective ferromagnetic film thickness simultaneously decreases. These results suggest that exchange bias involves some deformation of magnetic order in the interface region.

  9. Thrust Stand for Vertically Oriented Electric Propulsion Performance Evaluation

    Science.gov (United States)

    Moeller, Trevor; Polzin, Kurt A.

    2010-01-01

    A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally-stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A non-contact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational restoring force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN-level thrusts, while those tests conducted on 200 lbm thruster yielded a resolution of roughly 2.5 micro at thrust levels of 0.5 N and greater.

  10. Preliminary optimal configuration on free standing hybrid riser

    Directory of Open Access Journals (Sweden)

    Kyoung-Su Kim

    2018-05-01

    Full Text Available Free Standing Hybrid Riser (FSHR is comprised of vertical steel risers and Flexible Jumpers (FJ. They are jointly connected to a submerged Buoyancy Can (BC. There are several factors that have influence on the behavior of FSHR such as the span distance between an offshore platform and a foundation, BC up-lift force, BC submerged location and FJ length.An optimization method through a parametric study is presented. Firstly, descriptions for the overall arrangement and characteristics of FSHR are introduced. Secondly, a flowchart for optimization of FSHR is suggested. Following that, it is described how to select reasonable ranges for a parametric study and determine each of optimal configuration options. Lastly, numerical analysis based on this procedure is performed through a case study. In conclusion, the relation among those parameters is analyzed and non-dimensional parametric ranges on optimal arrangements are suggested. Additionally, strength analysis is performed with variation in the configuration. Keywords: Free standing hybrid riser, Hybrid riser system, Buoyancy can, Flexible jumper, Deepwater, Multi-body dynamics

  11. Thrust stand for vertically oriented electric propulsion performance evaluation

    International Nuclear Information System (INIS)

    Moeller, Trevor; Polzin, Kurt A.

    2010-01-01

    A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A noncontact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy-current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN level thrusts, while those tests conducted on a 200 lbm thruster yielded a resolution of roughly 2.5 mN at thrust levels of 0.5 N and greater.

  12. Methods for registration laser scanner point clouds in forest stands

    International Nuclear Information System (INIS)

    Bienert, A.; Pech, K.; Maas, H.-G.

    2011-01-01

    Laser scanning is a fast and efficient 3-D measurement technique to capture surface points describing the geometry of a complex object in an accurate and reliable way. Besides airborne laser scanning, terrestrial laser scanning finds growing interest for forestry applications. These two different recording platforms show large differences in resolution, recording area and scan viewing direction. Using both datasets for a combined point cloud analysis may yield advantages because of their largely complementary information. In this paper, methods will be presented to automatically register airborne and terrestrial laser scanner point clouds of a forest stand. In a first step, tree detection is performed in both datasets in an automatic manner. In a second step, corresponding tree positions are determined using RANSAC. Finally, the geometric transformation is performed, divided in a coarse and fine registration. After a coarse registration, the fine registration is done in an iterative manner (ICP) using the point clouds itself. The methods are tested and validated with a dataset of a forest stand. The presented registration results provide accuracies which fulfill the forestry requirements [de

  13. Free-standing nanocomposites with high conductivity and extensibility

    International Nuclear Information System (INIS)

    Chun, Kyoung-Yong; Kim, Shi Hyeong; Shin, Min Kyoon; Kim, Seon Jeong; Kim, Youn Tae; Spinks, Geoffrey M; Aliev, Ali E; Baughman, Ray H

    2013-01-01

    The prospect of electronic circuits that are stretchable and bendable promises tantalizing applications such as skin-like electronics, roll-up displays, conformable sensors and actuators, and lightweight solar cells. The preparation of highly conductive and highly extensible materials remains a challenge for mass production applications, such as free-standing films or printable composite inks. Here we present a nanocomposite material consisting of carbon nanotubes, ionic liquid, silver nanoparticles, and polystyrene–polyisoprene–polystyrene having a high electrical conductivity of 3700 S cm −1 that can be stretched to 288% without permanent damage. The material is prepared as a concentrated dispersion suitable for simple processing into free-standing films. For the unstrained state, the measured thermal conductivity for the electronically conducting elastomeric nanoparticle film is relatively high and shows a non-metallic temperature dependence consistent with phonon transport, while the temperature dependence of electrical resistivity is metallic. We connect an electric fan to a DC power supply using the films to demonstrate their utility as an elastomeric electronic interconnect. The huge strain sensitivity and the very low temperature coefficient of resistivity suggest their applicability as strain sensors, including those that operate directly to control motors and other devices. (paper)

  14. Large source test stand for H-(D-) ion source

    International Nuclear Information System (INIS)

    Larson, R.; McKenzie-Wilson, R.

    1981-01-01

    The Brookhaven National Laboratory Neutral Beam Group has constructed a large source test stand for testing of the various source modules under development. The first objective of the BNL program is to develop a source module capable of delivering 10A of H - (D - ) at 25 kV operating in the steady state mode with satisfactory gas and power efficiency. The large source test stand contains gas supply and vacuum pumping systems, source cooling systems, magnet power supplies and magnet cooling systems, two arc power supplies rated at 25 kW and 50 kW, a large battery driven power supply and an extractor electrode power supply. Figure 1 is a front view of the vacuum vessel showing the control racks with the 36'' vacuum valves and refrigerated baffles mounted behind. Figure 2 shows the rear view of the vessel with a BNL Mk V magnetron source mounted in the source aperture and also shows the cooled magnet coils. Currently two types of sources are under test: a large magnetron source and a hollow cathode discharge source

  15. Ecosystem Responses to Partial Harvesting in Eastern Boreal Mixedwood Stands

    Directory of Open Access Journals (Sweden)

    Brian D. Harvey

    2013-05-01

    Full Text Available Partial harvesting has been proposed as a key aspect to implementing ecosystem management in the Canadian boreal forest. We report on a replicated experiment located in boreal mixedwoods of Northwestern Quebec. In the winter of 2000–2001, two partial harvesting treatments, one using a dispersed pattern, and a second, which created a (400 m2 gap pattern, were applied to a 90-year-old aspen-dominated mixed stand. The design also included a clear cut and a control. Over the course of the following eight years, live tree, coarse woody debris, regeneration and ground beetles were inventoried at variable intervals. Our results indicate that all harvesting treatments created conditions favorable to balsam fir (Abies balsamea sapling growth and trembling aspen (Populus tremuloides sapling recruitment. However, balsam fir and trembling aspen regeneration and ground beetles response to gap cuts were closer to patterns observed in clear cuts than in dispersed harvesting. The underlying reasons for these differing patterns can be linked to factors associated with the contrasting light regimes created by the two partial harvesting treatments. The study confirms that partially harvesting is an ecologically sound approach in boreal mixedwoods and could contribute to maintaining the distribution of stand ages at the landscape level.

  16. Thin film characterization by resonantly excited internal standing waves

    Energy Technology Data Exchange (ETDEWEB)

    Di Fonzio, S [SINCROTRONE TRIESTE, Trieste (Italy)

    1996-09-01

    This contribution describes how a standing wave excited in a thin film can be used for the characterization of the properties of the film. By means of grazing incidence X-ray reflectometry one can deduce the total film thickness. On the other hand in making use of a strong resonance effect in the electric field intensity distribution inside a thin film on a bulk substrate one can learn more about the internal structure of the film. The profile of the internal standing wave is proven by diffraction experiments. The most appropriate non-destructive technique for the subsequent thin film characterization is angularly dependent X-ray fluorescence analysis. The existence of the resonance makes it a powerful tool for the detection of impurities and of ultra-thin maker layers, for which the position can be determined with very high precision (about 1% of the total film thickness). This latter aspect will be discussed here on samples which had a thin Ti marker layer at different positions in a carbon film. Due to the resonance enhancement it was still possible to perform these experiments with a standard laboratory x-ray tube and with standard laboratory tool for marker or impurity detection in thin films.

  17. Electrical behavior of free-standing porous silicon layers

    International Nuclear Information System (INIS)

    Bazrafkan, I.; Dariani, R.S.

    2009-01-01

    The electrical behavior of porous silicon (PS) layers has been investigated on one side of p-type silicon with various anodization currents and electrolytes. The two contact I-V characteristic is assigned by the metal/porous silicon rectifying interface, whereas, by using the van der Pauw technique, a nonlinear dependence of the current vs voltage was found. By using Dimethylformamide (DMF) in electrolyte, regular structures and columns were formed and porosity increased. Our results showed that by using DMF, surface resistivity of PS samples increased and became double for free-standing porous silicon (FPS). The reason could be due to increasing surface area and adsorbing some more gas molecules. Activation energy of PS samples was also increased from 0.31 to 0.34 eV and became 0.35 eV for FPS. The changes induced by storage are attributed to the oxidation process of the internal surface of free-standing porous silicon layers.

  18. Multimode laser emission from free-standing cylindrical microcavities

    Energy Technology Data Exchange (ETDEWEB)

    Peter, Jaison, E-mail: jaisonpeter@cusat.ac.in; Radhakrishnan, P.; Nampoori, V.P.N.; Kailasnath, M.

    2014-05-01

    We report a well resolved whispering gallery mode (WGM) laser emission from a free-standing microring cavity based on a dye doped hollow polymer optical fiber (DDHPOF), which is transversely pumped by a pulsed Nd:YAG laser. The microring laser is characterized by a well-defined, low threshold pump power at which the emission spectral intensity dramatically increases and collapses into several dominant microcavity laser modes with reduced mode spacing and high Q-value. Resonant modes are excited inside the gain medium which is strongly confined along the radial direction so that the spacing of lasing modes is controlled by the diameter of the cylindrical microcavity. A variation in the free spectral range of WGM spectra from 0.23 to 0.09 nm coupled with a red-shift is observed with an increase in the diameter of DDHPOFs. - Highlights: • Different diameter free-standing cylindrical microcavity lasers have been fabricated and their performances have been evaluated. • The microring laser is characterized by a well-defined, low threshold pump power, with reduced mode spacing and high Q-value. • When the diameter of DDHPOF increases, the number of lasing peaks increases along with the decrease of the FSR as observed from our studies. • It is also found that whispering gallery lasing envelope is shifted from 559 to 571 nm (Stokes shift) with the diameter.

  19. The effect of a sit-stand workstation intervention on daily sitting, standing and physical activity: protocol for a 12 month workplace randomised control trial.

    Science.gov (United States)

    Hall, Jennifer; Mansfield, Louise; Kay, Tess; McConnell, Alison K

    2015-02-15

    A lack of physical activity and excessive sitting can contribute to poor physical health and wellbeing. The high percentage of the UK adult population in employment, and the prolonged sitting associated with desk-based office-work, make these workplaces an appropriate setting for interventions to reduce sedentary behaviour and increase physical activity. This pilot study aims to determine the effect of an office-based sit-stand workstation intervention, compared with usual desk use, on daily sitting, standing and physical activity, and to examine the factors that underlie sitting, standing and physical activity, within and outside, the workplace. A randomised control trial (RCT) comparing the effects of a sit-stand workstation only and a multi-component sit-stand workstation intervention, with usual desk-based working practice (no sit-stand workstation) will be conducted with office workers across two organisations, over a 12 month period (N = 30). The multicomponent intervention will comprise organisational, environmental and individual elements. Objective data will be collected at baseline, and after 2-weeks, 3-months, 6-months and 12-months of the intervention. Objective measures of sitting, standing, and physical activity will be made concurrently (ActivPAL3™ and ActiGraph (GT3X+)). Activity diaries, ethnographic participant observation, and interviews with participants and key organisational personnel will be used to elicit understanding of the influence of organisational culture on sitting, standing and physical activity behaviour in the workplace. This study will be the first long-term sit-stand workstation intervention study utilising an RCT design, and incorporating a comprehensive process evaluation. The study will generate an understanding of the factors that encourage and restrict successful implementation of sit-stand workstation interventions, and will help inform future occupational wellbeing policy and practice. Other strengths include the

  20. Association of unipedal standing time and bone mineral density in community-dwelling Japanese women.

    Science.gov (United States)

    Sakai, A; Toba, N; Takeda, M; Suzuki, M; Abe, Y; Aoyagi, K; Nakamura, T

    2009-05-01

    Bone mineral density (BMD) and physical performance of the lower extremities decrease with age. In community-dwelling Japanese women, unipedal standing time, timed up and go test, and age are associated with BMD while in women aged 70 years and over, unipedal standing time is associated with BMD. The aim of this study was to clarify whether unipedal standing time is significantly associated with BMD in community-dwelling women. The subjects were 90 community-dwelling Japanese women aged 54.7 years. BMD of the second metacarpal bone was measured by computed X-ray densitometry. We measured unipedal standing time as well as timed up and go test to assess physical performance of the lower extremities. Unipedal standing time decreased with increased age. Timed up and go test significantly correlated with age. Low BMD was significantly associated with old age, short unipedal standing time, and long timed up and go test. Stepwise regression analysis revealed that age, unipedal standing time, and timed up and go test were significant factors associated with BMD. In 21 participants aged 70 years and over, body weight and unipedal standing time, but not age, were significantly associated with BMD. BMD and physical performance of the lower extremities decrease with older age. Unipedal standing time, timed up and go test, and age are associated with BMD in community-dwelling Japanese women. In women aged 70 years and over, unipedal standing time is significantly associated with BMD.

  1. Chemodiversity in terpene emissions at a boreal Scots pine stand

    Science.gov (United States)

    Bäck, J.; Aalto, J.; Henriksson, M.; Hakola, H.; He, Q.; Boy, M.

    2011-10-01

    Atmospheric chemistry in background areas is strongly influenced by natural vegetation. Coniferous forests are known to produce large quantities of volatile vapors, especially terpenes to the surrounding air. These compounds are reactive in the atmosphere, and contribute to the formation and growth of atmospheric new particles. Our aim was to analyze the variability of mono- and sesquiterpene emissions between Scots pine trees, in order to clarify the potential errors caused by using emission data obtained from only a few trees in atmospheric chemistry models. We also aimed at testing if stand history and seed origin has an influence on the chemotypic diversity. The inherited, chemotypic variability in mono- and sesquiterpene emission was studied in a seemingly homogeneous 47-yr-old stand in Southern Finland, where two areas differing in their stand regeneration history could be distinguished. Sampling was conducted in August 2009. Terpene concentrations in the air had been measured at the same site for seven years prior to branch sampling for chemotypes. Two main compounds, α-pinene and Δ3-carene formed together 40-97% of the monoterpene proportions in both the branch emissions and in the air concentrations. The data showed a bimodal distribution in emission composition, in particular in Δ3-carene emission within the studied population. 10% of the trees emitted mainly α-pinene and no Δ3-carene at all, whereas 20% of the trees where characterized as high Δ3-carene emitters (Δ3-carene forming >80% of total emitted monoterpene spectrum). An intermediate group of trees emitted equal amounts of both α-pinene and Δ3-carene. The emission pattern of trees at the area established using seeding as the artificial regeneration method differed from the naturally regenerated or planted trees, being mainly high Δ3-carene emitters. Some differences were also seen in e.g. camphene and limonene emissions between chemotypes, but sesquiterpene emissions did not differ

  2. Age estimates for the late quaternary high sea-stands

    Science.gov (United States)

    Smart, Peter L.; Richards, David A.

    A database of more than 300 published alpha-counted uranium-series ages has been compiled for coral reef terraces formed by Late Pleistocene high sea-stands. The database was screened to eliminate unreliable age estimates ( {230Th }/{232Th } 5%) and those without quoted without quoted errors, and a distributed error frequency curve was produced. This curve can be considered as a finite mixture model comprising k component normal distributions each with a weighting α. By using an expectation maximising algorithm, the mean and standard deviation of the component distributions, each corresponding to a high sea level event, were estimated. Eight high sea-stands with mean and standard deviations of 129.0 ± 33.0, 123.0 ± 13.0, 102.5 ± 2.0, 81.5 ± 5.0, 61.5 ± 6.0, 50.0 ± 1.0, 40.5 ± 5.0 and 33.0 ± 2.5 ka were resolved. The standard deviations are generally larger than the values quoted for individual age estimates. Whilst this may be due to diagenetic effects, especially for the older corals, it is argued that in many cases geological evidence clearly indicates that the high stands are multiple events, often not resolvable at sites with low rates of uplift. The uranium-series dated coral-reef terrace chronology shows good agreement with independent chronologies derived for Antarctic ice cores, although the resolution for the latter is better. Agreement with orbitally-tuned deep-sea core records is also good, but it is argued that Isotope Stage 5e is not a single event, as recorded in the cores, but a multiple event spanning some 12 ka. The much earlier age for Isotope Stage 5e given by Winograd et al. (1988) is not supported by the coral reef data, but further mass-spectrometric uranium-series dating is needed to permit better chronological resolution.

  3. From a tree to a stand in Finnish boreal forests - biomass estimation and comparison of methods

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chunjiang

    2009-07-01

    There is an increasing need to compare the results obtained with different methods of estimation of tree biomass in order to reduce the uncertainty in the assessment of forest biomass carbon. In this study, tree biomass was investigated in a 30-year-old Scots pine (Pinus sylvestris) (Young-Stand) and a 130-year-old mixed Norway spruce (Picea abies)-Scots pine stand (Mature-Stand) located in southern Finland (61deg50' N, 24deg22' E). In particular, a comparison of the results of different estimation methods was conducted to assess the reliability and suitability of their applications. For the trees in Mature-Stand, annual stem biomass increment fluctuated following a sigmoid equation, and the fitting curves reached a maximum level (from about 1 kg yr-1 for understorey spruce to 7 kg yr-1 for dominant pine) when the trees were 100 years old). Tree biomass was estimated to be about 70 Mg ha-1 in Young-Stand and about 220 Mg ha-1 in Mature-Stand. In the region (58.00-62.13 degN, 14-34 degE, <= 300 m a.s.l.) surrounding the study stands, the tree biomass accumulation in Norway spruce and Scots pine stands followed a sigmoid equation with stand age, with a maximum of 230 Mg ha-1 at the age of 140 years. In Mature-Stand, lichen biomass on the trees was 1.63 Mg ha-1 with more than half of the biomass occurring on dead branches, and the standing crop of litter lichen on the ground was about 0.09 Mg ha-1. There were substantial differences among the results estimated by different methods in the stands. These results imply that a possible estimation error should be taken into account when calculating tree biomass in a stand with an indirect approach. (orig.)

  4. STANDING CONCERTATION COMMMITTEE - ORDINARY MEETING ON 26 JUNE 2007

    CERN Multimedia

    HR Department

    2007-01-01

    The main items discussed at the meeting of the Standing Concertation Committee on 26 June 2007 included: Mutual Aid Fund The Committee took note of the annual report for 2006 by the Chairman of the Mutual Aid Fund and approved contributions to the Fund’s budget from the Management and the Staff Association and thanked the members of the Fund for their work. Administrative Circular No. 12 A (Rev. 1) - Education Fees The Committee agreed to recommend Administrative Circular No. 12 A entitled "Education Fees" to the Director-General for approval. The circular is applicable to staff, fellows and scientific associates recruited from 1st January 2007 and to staff who were recruited as Local Staff before that date. Further details of reimbursement of school fees will shortly be available in the form of Frequently Asked Questions on the HR Department website. Administrative Circular No. 31 (Rev. 1) - International Indemnity and Non-Resident Allowance The Committee agreed to reco...

  5. Peer effects in unethical behavior: standing or reputation?

    Directory of Open Access Journals (Sweden)

    David Pascual-Ezama

    Full Text Available Recent empirical evidence shows that working in an unsupervised, isolated situation under competition, can increase dishonest behavior to achieve prestige. However, could working in a common space, in the presence of colleagues affect cheating? Here, we examine how familiar-peer influence, supervision and social incentives affect worker performance and dishonest behavior. First, we show that working in the presence of peers is an effective mechanism to constrain honest/dishonest behavior compared to an isolated work situation (experiment 1. Second, we demonstrate that the mere suspicion of dishonesty from another peer is not enough to affect individual cheating behavior (experiment 2, suggesting that reputation holds great importance in a worker's self-image acting as a strong social incentives. Third, we show that when the suspicion of dishonesty increases with multiple peers behaving dishonestly, the desire to increase standing is sufficient to nudge individuals' behavior back to cheating at the same levels as isolated situations (experiment 3.

  6. Standing Concertation Committee - Ordinary Meeting on 3 September 2008

    CERN Multimedia

    HR Department

    2008-01-01

    The main items discussed at the meeting of the Standing Concertation Committee on 3 September 2008 included: Education fees: Indexation of the amounts for accommodation and meals The Committee approved the indexation calculations for accommodation and meals for the academic year 2008-2009. With the indexation of the lump sum payments, accommodation costs for the academic year 2007-2008 will be reimbursed at 529 CHF per month (previously CHF 500). Meals will be reimbursed at 17.50 CHF per meal (unchanged). The ceiling for school transport has been increased from 600 CHF to 622 CHF. Administrative Circular No. 26 (Rev. 8) The Committee took note of the modifications to Administrative Circular No. 26 (Rev. 8) ‘Recognition of merit of staff members’, concerning provision for the award of exceptional advancement outside the annual advancement exercise to recognize, for example, the completion of a major project. HR Survey The Committee took note of the Head of HR Department...

  7. The electric field standing wave effect in infrared transflection spectroscopy

    Science.gov (United States)

    Mayerhöfer, Thomas G.; Popp, Jürgen

    2018-02-01

    We show that an electric field standing wave effect is responsible for the oscillations and the non-linear dependence of the absorbance on the layer thickness in thin layers on a reflective surface. This effect is connected to the occurrence of interference inside these layers. Consequently, the absorptance undergoes a maximum electric field intensity enhancement at spectral positions close to those where corresponding non-absorbing layers on a metal show minima in the reflectance. The effect leads to changes of peak maxima ratios with layer thickness and shows the same periodicity as oscillations in the peak positions. These peculiarities are fully based on and described by Maxwell's equations but cannot be understood and described if the strongly simplifying model centered on reflectance absorbance is employed.

  8. STANDING CONCERTATION COMMMITTEE - ORDINARY MEETING ON 28 AUGUST 2007

    CERN Multimedia

    HR Department

    2007-01-01

    The main items discussed at the meeting of the Standing Concertation Committee on 28 August 2007 included: Administrative Circular No. 12 A (Rev. 1) - Education Fees The Committee agreed to recommend Administrative Circular No. 12 A, "Education Fees", to the Director-General for approval. The circular is applicable to staff, fellows and scientific associates recruited before 1 January 2007 (except for local staff). Administrative Circular No. 12 B applies to those recruited from 1 January 2007 and was examined by the Committee in June 2007. It was noted that, at the initiative of HR Department, a number of important simplifications have been introduced. These cover, in particular, lump-sum payments to compensate for accommodation, meals and journey expenses. Further details of payment of education fees will shortly be available in the form of Frequently Asked Questions on the HR Department website. The Chairman thanked HR Department as well as "Team 7" members for init...

  9. STANDING CONCERTATION COMMMITTEE - ORDINARY MEETING ON 28 AUGUST 2007

    CERN Document Server

    HR Department

    2007-01-01

    The main items discussed at the meeting of the Standing Concertation Committee on 28 August 2007 included: Administrative Circular No. 12 A (Rev. 1) - Education Fees The committee agreed to recommend Administrative Circular No. 12 A, Education Fees, to the Director-General for approval. The circular is applicable to staff, fellows and scientific associates recruited before 1 January 2007 (except for local staff). Administrative Circular No. 12 B applies to those recruited from 1 January 2007 and was considered by the committee in June 2007. It was noted that, at the initiative of HR Department, a number of important simplifications have been introduced. These cover in particular lump sum payments to compensate for accommodation, meals and journey expenses. Further details of payment of education fees will shortly be available in the form of Frequently Asked Questions on the HR Department website. The Chairman thanked HR Department as well as "Team 7" members for initiating these simp...

  10. Psycholegal abilities and restoration of competence to stand trial.

    Science.gov (United States)

    Morris, Douglas R; Deyoung, Nathaniel J

    2012-01-01

    Criminal defendants adjudicated incompetent to stand trial are typically hospitalized for competence restoration in state institutions. Prolonged restoration hospitalizations involve civil rights concerns and increasing financial costs, and there remains interest in determining which individuals are likely to be successfully restored. We retrospectively reviewed hospital records of 455 male defendants admitted to a forensic treatment center for competence restoration in an effort to determine whether psychiatric diagnoses, demographic factors, or psycholegal abilities were predictive of successful or failed restoration. At varying stages of restoration efforts, psychotic disorder, mental retardation, and previous state hospitalization predicted unsuccessful restoration, while substance use and personality disorders were predictive of successful restoration. Psycholegal abilities were predictive of successful restoration and appeared to form a continuum, with basic behavior and outlook, factual legal understanding, and rational attorney assistance factors demonstrating progressively increased importance in successful restoration. Copyright © 2012 John Wiley & Sons, Ltd.

  11. Earthquake stand-by instruction device for nuclear power plant

    International Nuclear Information System (INIS)

    Nakagawa, Masaki; Ijima, Tadashi

    1998-01-01

    The magnitude of earthquakes is forecast at a high accuracy by disposing seismic detectors to a plurality of points distant from an object plant. The accuracy of the judgement for the magnitude of earthquakes can be improved by processing seismic movements by using seismic movements observed along with elapse of time. The measured seismic waveforms are always stored even during the processing time. With such procedures, when one processing is completed, processing can be conducted successively by using stored data, by which processing can be conducted by using all the data from the occurrence of the earthquakes. Then, the seismic movements can be estimated from an early stage of the occurrence of the earthquakes, and since the seismic movement can be judged based on a great amount of data with lapse of time, an appropriate stand-by instruction can be provided. (N.H.)

  12. FEATURES OF WTO DISPUTE SETTLEMENT. THE STANDING OF THE EU

    Directory of Open Access Journals (Sweden)

    Costin Horia Rogoveanu

    2010-09-01

    Full Text Available The WTO has an innovative system of dispute settlement, with the following features: sui-generis, integrated, resolving the disputes according to the WTO agreements, excluding unilateral solutions, interstate system. These features are detailed in the present article. Another level of analysis concerns the standing of the EU in the WTO, in general, and in the Geneva proceedings for dispute settlement, in particular. Generated by the quality of the European Communities statute as an original member of the Organisation, the EU has become one of the main users of the WTO dispute settlement system. One of the main challenges of the WTO dispute settlement mechanism is the implementation of decisions. In view of the cases assessed, while the execution record of the EU is a quite satisfactory one, it is apparent that implementation of decisions in more intricate cases creates difficulties at the Union level.

  13. Competency to stand trial: rationalism, "contextualism" and other modest theories.

    Science.gov (United States)

    Jan Brakel, S

    2003-01-01

    Determinations of competency to stand trial in criminal cases are complicated and rendered unpredictable by two sub-surface issues that are rarely articulated: (i) the place of the defendant's rationality in the substantive standard(s) for competency and (ii) the level or degree of incompetency required to stop the criminal process. The rare references to these issues, mostly indirect, that are made in the cases, commentary, and competency testing instruments devised (including those civil as well as criminal) are examined. The conclusion that emerges is that the level of capacity and rationality required of the defendant depends much on context-the type of case, its relative complexity, and the values and stakes implicated in the outcome. Copyright 2003 John Wiley & Sons, Ltd.

  14. Beam loading effects in a standing wave accelerator structure

    International Nuclear Information System (INIS)

    Arai, Shigeaki; Katayama, Takeshi; Tojyo, Eiki; Yoshida, Katsuhide.

    1978-11-01

    The steady-state beam loading effects on the accelerating field in the disk-loaded structure of a standing wave type have been systematically studied. The electron bunch from a 15 MeV electron linac is injected at arbitrary phase of the external driving field in the test structure. The change of the phase shift of the accelerating field and that of the stored energy are measured as a function of the phase on which the bunch rides. The former shows drastic change when the bunch is around the crest of the driving field and when the beam loading is heavy, whereas the latter varies sinusoidally for any beam loading. The resonant frequency shift of the structure due to beam loading is estimated by using the measured results. All the experimental results are well explained by the normal mode analysis of the microwave cavity theory. (author)

  15. Hydrogen Gas Production in a Stand-Alone Wind Farm

    Directory of Open Access Journals (Sweden)

    M. Naziry Kordkandy

    2017-04-01

    Full Text Available This paper is analyzing the operation of a stand-alone wind farm with variable speed turbines, permanent magnet synchronous generators (PMSG and a system for converting wind energy during wind speed variations. On this paper, the design and modeling of a wind system which uses PMSG’s to provide the required power of a hydrogen gas electrolyzer system, is discussed. This wind farm consists of three wind turbines, boost DC-DC converters, diode full bridge rectifiers, permanent magnet synchronous generators, MPPT control and a hydrogen gas electrolyzer system. The MPPT controller based on fuzzy logic is designed to adjust the duty ratio of the boost DC-DC converters to absorb maximum power. The proposed fuzzy logic controller assimilates, with (PSF MPPT algorithm which generally used to absorb maximum power from paralleled wind turbines and stores it in form of hydrogen gas. The system is modeled and its behavior is studied using the MATLAB software.

  16. Measurement by a cylinder test stand and tyre rolling resistance

    Directory of Open Access Journals (Sweden)

    A. Dávid

    2006-03-01

    Full Text Available Sometimes it is necessary to test how repair affects the properties of the car. These tests are carried out using a cylinder test stand. During the test the tyre is rolling between two cylinders of a small diameter. The question arises whether the rolling resistance of the tyre is the same as the rolling resistance when the wheel is rolling on the plane. If it is not the same what is the reliation between tyre resistances in these two cases? It is an important answer because the change of rolling resistance can affect consumption, the highest speed, engine power and other results of measurement. The paper gives the answer to these questions and describes the method of getting this information.

  17. Magnetic field measurements near stand-alone transformer stations.

    Science.gov (United States)

    Kandel, Shaiela; Hareuveny, Ronen; Yitzhak, Nir-Mordechay; Ruppin, Raphael

    2013-12-01

    Extremely low-frequency (ELF) magnetic field (MF) measurements around and above three stand-alone 22/0.4-kV transformer stations have been performed. The low-voltage (LV) cables between the transformer and the LV switchgear were found to be the major source of strong ELF MFs of limited spatial extent. The strong fields measured above the transformer stations support the assessment method, to be used in future epidemiological studies, of classifying apartments located right above the transformer stations as highly exposed to MFs. The results of the MF measurements above the ground around the transformer stations provide a basis for the assessment of the option of implementing precautionary procedures.

  18. Standing torsional waves in a fully saturated, porous, circular cylinder

    CERN Document Server

    Solorza, S; 10.1111/j.1365-246X.2004.02198.x

    2004-01-01

    For dynamic measurement of the elastic moduli of a porous material saturated with viscous fluid using the resonance-bar technique, one also observes attenuation. In this article we have carried out the solution of the boundary-value problem associated with standing torsional oscillations of a finite, poroelastic, circular cylinder cast in the framework of volume-averaged theory of poroelasticity. Analysing this solution by eigenvalue perturbation approach we are able to develop expressions for torsional resonance and temporal attenuation frequencies in which the dependence upon the material properties are transparent. It shows how the attenuation is controlled by the permeability and the fluid properties, and how the resonance frequency drops over its value for the dry solid-frame due to the drag effect of fluid mass. Based upon this work we have a firm basis to determine solid-frame shear modulus, permeability, and tortuosity factor from torsional oscillation experiments.

  19. Modeling higher education attractiveness to stand global environment

    Directory of Open Access Journals (Sweden)

    Leonel Cezar Rodrigues

    2016-04-01

    Full Text Available Inabilities to deal with the changing environment may lead Higher Education Institutions (HEI to loose institutional attractiveness. Digital transformation requires global insertion as essential feature to institutional attractiveness. Processes for international education seem to lack the links between real environmental trends and the internal capabilities to global education. HEI managers may approach endeavors to internationalize education combining ambidextrous strategy supported by consolidated resilience capabilities. The latest ones refer to building internal value attributes to increase institutional attractiveness assuring solid standing in the global environment. In this article, a theoretical essay, we approach the problem of creating resilience as a way of backing up ambidexterity to generate institutional attractiveness. The set of value attributes, on the other hand, may originate strategic routes to strengthen internal competences and to make the institution more attractive, as a dynamic capability.

  20. Standing Concertation Commmittee - Ordinary meeting on 10 May 2007

    CERN Multimedia

    2007-01-01

    At its meeting on 10 May 2007, the Standing Concertation Committee discussed the Management’s proposal for the revision of Annex A 1 of the Staff Rules and Regulations. Annex A 1 sets out the principles for future periodic reviews of the personnel’s financial and social conditions and the revision reflects the modifications to review methods decided by the CERN Council in December 2006. The aim is to simplify the processes involved and rationalize the use of resources. The data collection process will be outsourced to a greater extent. The new methods also aim to reduce the overall time required to complete future reviews. Details of procedure will be addressed in subsequent discussions. The Committee approved the document for submission to the Tripartite Employment Conditions Forum (TREF) at its meeting on 31 May and 1 June 2007.

  1. Standing Concertation Commmittee - Ordinary meeting on 27 March 2007

    CERN Multimedia

    HR Department

    2007-01-01

    The main items discussed at the meeting of the Standing Concertation Committee on 27 March 2007 included: Merit Recognition Guidelines In the context of the new Merit Appraisal and Recognition Scheme (MARS), the committee took note of the documents entitled 'MARS Guidelines 2007' and the 'Guidelines for Senior Staff Advancement 2007'. Follow-up of Finance Committee and Council meetings The Committee took note of the information provided by S. Lettow, the Director for Finance and Human Resources, including the possibility for a phased increase in Member State contributions from 2008. Registered partnerships It was agreed that staff members with registered partners should be reminded of the social cover available to their partners. Cover is limited to the CERN Health Insurance Scheme and partners may be covered by the Scheme only while the staff member is working. On the staff member's retirement or other change in status, or death, partners are no longer eligible for CHIS cover. Retirement semi...

  2. Standing Concertation Commmittee - Ordinary meeting on 27 March 2007

    CERN Multimedia

    HR Department

    2007-01-01

    The main items discussed at the meeting of the Standing Concertation Committee on 27 March 2007 included: Merit Recognition Guidelines : in the context of the new Merit Appraisal and Recognition Scheme (MARS), the committee took note of the documents entitled MARS Guidelines 2007 and the Guidelines for Senior Staff Advancement 2007. Follow-up of Finance Committee and Council meetings The Committee took note of the information provided by S. Lettow, the Director for Finance and Human Resources, including the possibility for a phased increase in Member State contributions from 2008. Registered partnerships It was agreed that staff members with registered partners should be reminded of the social cover available to their partners. Cover is limited to the CERN Health Insurance Scheme and partners may be covered by the Scheme only while the staff member is working. On the staff members retirement or other change in status, or death, partners are no longer eligible for CHIS cover. Retirement seminars It...

  3. Ethernet-based test stand for a CAN network

    Science.gov (United States)

    Ziebinski, Adam; Cupek, Rafal; Drewniak, Marek

    2017-11-01

    This paper presents a test stand for the CAN-based systems that are used in automotive systems. The authors propose applying an Ethernet-based test system that supports the virtualisation of a CAN network. The proposed solution has many advantages compared to classical test beds that are based on dedicated CAN-PC interfaces: it allows the physical constraints associated with the number of interfaces that can be simultaneously connected to a tested system to be avoided, which enables the test time for parallel tests to be shortened; the high speed of Ethernet transmission allows for more frequent sampling of the messages that are transmitted by a CAN network (as the authors show in the experiment results section) and the cost of the proposed solution is much lower than the traditional lab-based dedicated CAN interfaces for PCs.

  4. Cryomdoule Test Stand Reduced-Magnetic Support Design at Fermilab

    Energy Technology Data Exchange (ETDEWEB)

    McGee, Mike [Fermilab; Chandrasekaran, Saravan Kumar [Fermilab; Crawford, Anthony [Fermilab; Harms, Elvin [Fermilab; Leibfritz, Jerry [Fermilab; Wu, Genfa [Fermilab

    2016-06-01

    In a partnership with SLAC National Accelerator Laboratory (SLAC) and Jefferson Lab, Fermilab will assemble and test 17 of the 35 total 1.3 GHz cryomodules for the Linac Coherent Light Source II (LCLS-II) Project. These devices will be tested at Fermilab's Cryomodule Test Facility (CMTF) within the Cryomodule Test Stand (CMTS-1) cave. The problem of magnetic pollution became one of major issues during design stage of the LCLS-II cryomodule as the average quality factor of the accelerating cavities is specified to be 2.7 x 10¹⁰. One of the possible ways to mitigate the effect of stray magnetic fields and to keep it below the goal of 5 mGauss involves the application of low permeable materials. Initial permeability and magnetic measurement studies regarding the use of 316L stainless steel material indicated that cold work (machining) and heat affected zones from welding would be acceptable.

  5. Slot-coupled CW standing wave accelerating cavity

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shaoheng; Rimmer, Robert; Wang, Haipeng

    2017-05-16

    A slot-coupled CW standing wave multi-cell accelerating cavity. To achieve high efficiency graded beta acceleration, each cell in the multi-cell cavity may include different cell lengths. Alternatively, to achieve high efficiency with acceleration for particles with beta equal to 1, each cell in the multi-cell cavity may include the same cell design. Coupling between the cells is achieved with a plurality of axially aligned kidney-shaped slots on the wall between cells. The slot-coupling method makes the design very compact. The shape of the cell, including the slots and the cone, are optimized to maximize the power efficiency and minimize the peak power density on the surface. The slots are non-resonant, thereby enabling shorter slots and less power loss.

  6. Standing shocks in adiabatic black hole accretion of rotating matter

    International Nuclear Information System (INIS)

    Abramowicz, M.A.; Chakrabarti, S.K.

    1988-08-01

    We present all the solutions for stationary, axially symmetric, transonic, adiabatic flows with polytropic, rotating fluid configurations of small transverse thickness, in an arbitrarily chosen potential. Special attention is paid to the formation of the standing shocks in the case of black hole accretion and winds. We point out the possibility of three types of shocks depending upon three extreme physical conditions at the shocks. These are: Rankine-Hugoniot shocks, isentropic compression waves, and isothermal shocks. We write down the shock conditions for these three cases and discuss briefly the physical situations under which these shocks may form. A complete discussion on the properties of these shocks will be presented elsewhere. (author). 21 refs, 4 figs

  7. Standing Concertation Commmittee - Ordinary meeting on 10 May 2007

    CERN Multimedia

    HR Department

    2007-01-01

    At its meeting on 10 May 2007, the Standing Concertation Committee discussed the Management's proposal for the revision of Annex A 1 of the Staff Rules and Regulations. Annex A 1 sets out the principles for future periodic reviews of the personnel's financial and social conditions and the revision reflects the modifications to review methods decided by the CERN Council in December 2006. The aim is to simplify the processes involved and rationalize the use of resources. The data collection process will be outsourced to a greater extent. The new methods also aim to reduce the overall time required to complete future reviews. Details of procedure will be addressed in subsequent discussions. The Committee approved the document for submission to the Tripartite Employment Conditions Forum (TREF) at its meeting on 31 May and 1 June 2007.

  8. Food Irradiation. Standing legislation; Irradiacion de Alimentos. Legislacion Vigente

    Energy Technology Data Exchange (ETDEWEB)

    Verdejo S, M. [Secretaria de Salud. Subsecretaria de Regulacion y Fomento Sanitario. Direccion de Riesgos Radiologicos. Mariano Escobedo No. 366- 4o. Piso. Col. Nueva Anzures. Mexico D.F. (Mexico)

    1997-12-31

    The standing legislation in Mexico on food irradiation matter has its basis on the Constitutional Policy of the Mexican United States on the 4 Th. article by its refers to Secretary of Health, 27 Th. article to the Secretary of Energy and 123 Th. of the Secretary of Work and Social Security. The laws and regulations emanated of the proper Constitution establishing the general features which gives the normative frame to this activity. The general regulations of Radiological Safety expedited by the National Commission for Nuclear Safety and Safeguards to state the specifications which must be fulfill the industrial installations which utilizing ionizing radiations, between this line is founded, just as the requirements for the responsible of the radiological protection and the operation of these establishments. The project of Regulation of the General Health Law in matter of Sanitary Control of Benefits and Services, that in short time will be officialized, include a specific chapter on food irradiation which considers the International Organizations Recommendations and the pertaining harmonization stated for Latin America, which elaboration was in charge of specialized group where Mexico was participant. Additionally, the Secretary of Health has a Mexican Official Standard NOM-033-SSA1-1993 named `Food irradiation; permissible doses in foods, raw materials and support additives` standing from the year 1995, where is established the associated requirements to the control registers, service constancies and dose limits for different groups of foods, moreover of the specific guidelines for its process. This standard will be adequate considering the updating Regulation of Benefits and Services and the limits established the Regulation for Latin America. The associated laws that cover in general terms it would be the requirements for food irradiation although such term is not manageable. (Author)

  9. Integral type small PWR with stand-alone safety

    International Nuclear Information System (INIS)

    Makihara, Yoshiaki

    2001-01-01

    A feasibility study is achieved on an integral type small PWR with stand-alone safety. It is designed to have the following features. (1) The coolant does not leak out at any accidental condition. (2) The fuel failure does never occur while it is supposed on the large scale PWR at the design base accident. (3) At any accidental condition the safety is secured without any support from the outside (stand-alone safety secure). (4) It has self-regulating characteristics and easy controllability. The above features can be satisfied by integrate the steam generator and CRDM in the reactor vessel while the pipe line break has to be considered on the conventional PWR. Several counter measures are planned to satisfy the above features. The economy feature is also attained by several simplifications such as (1) elimination of main coolant piping and pressurizer by the integration of primary cooling system and self-pressurizing, (2) elimination of RCP by application of natural circulating system, (3) elimination of ECCS and accumulator by application of static safety system, (4) large scale volume reduction of the container vessel by application of integrated primary cooling system, (5) elimination of boric acid treatment by deletion of chemical shim. The long operation period such as 10 years can be attained by the application of Gd fuel in one batch refueling. The construction period can be shortened by the standardizing the design and the introduction of modular component system. Furthermore the applicability of the reduced modulation core is also considered. (K. Tsuchihashi)

  10. Photopatterned free-standing polyacrylamide gels for microfluidic protein electrophoresis.

    Science.gov (United States)

    Duncombe, Todd A; Herr, Amy E

    2013-06-07

    Designed for compatibility with slab-gel polyacrylamide gel electrophoresis (PAGE) reagents and instruments, we detail development of free-standing polyacrylamide gel (fsPAG) microstructures supporting electrophoretic performance rivalling that of microfluidic platforms. For the protein electrophoresis study described here, fsPAGE lanes are comprised of a sample reservoir and contiguous separation gel. No enclosed microfluidic channels are employed. The fsPAG devices (120 μm tall) are directly photopatterned atop of and covalently attached to planar polymer or glass surfaces. Leveraging the fast prototype-test cycle - significantly faster than mold based fabrication techniques - we optimize the fsPAG architecture to minimize injection dispersion for rapid (prototyping of the fsPAGE provides researchers a powerful tool for developing custom analytical assays. We highlight the utility of assay customization by fabricating a polyacrylamide gel with a spatial pore-size distribution and demonstrate the resulting enhancement in separation performance over a uniform gel. Further, we up-scale from a unit separation to an array of 96 concurrent fsPAGE assays in 10 min run time driven by one electrode pair. The fsPAG array layout matches that of a 96-well plate to facilitate integration of the planar free standing gel array with multi-channel pipettes while remaining compatible with conventional slab-gel PAGE reagents, such as staining for label-free protein detection. Notably, the entire fsPAGE workflow from fabrication, to operation, and readout uses readily available materials and instruments - making this technique highly accessible.

  11. Influence of real and virtual heights on standing balance.

    Science.gov (United States)

    Cleworth, Taylor W; Horslen, Brian C; Carpenter, Mark G

    2012-06-01

    Fear and anxiety induced by threatening scenarios, such as standing on elevated surfaces, have been shown to influence postural control in young adults. There is also a need to understand how postural threat influences postural control in populations with balance deficits and risk of falls. However, safety and feasibility issues limit opportunities to place such populations in physically threatening scenarios. Virtual reality (VR) has successfully been used to simulate threatening environments, although it is unclear whether the same postural changes can be elicited by changes in virtual and real threat conditions. Therefore, the purpose of this study was to compare the effects of real and virtual heights on changes to standing postural control, electrodermal activity (EDA) and psycho-social state. Seventeen subjects stood at low and high heights in both real and virtual environments matched in scale and visual detail. A repeated measures ANOVA revealed increases with height, independent of visual environment, in EDA, anxiety, fear, and center of pressure (COP) frequency, and decreases with height in perceived stability, balance confidence and COP amplitude. Interaction effects were seen for fear and COP mean position; where real elicited larger changes with height than VR. This study demonstrates the utility of VR, as simulated heights resulted in changes to postural, autonomic and psycho-social measures similar to those seen at real heights. As a result, VR may be a useful tool for studying threat related changes in postural control in populations at risk of falls, and to screen and rehabilitate balance deficits associated with fear and anxiety. Copyright © 2012 Elsevier B.V. All rights reserved.

  12. Abdominal muscle activity during a standing long jump.

    Science.gov (United States)

    Okubo, Yu; Kaneoka, Koji; Shiina, Itsuo; Tatsumura, Masaki; Miyakawa, Shumpei

    2013-08-01

    Experimental laboratory study. To measure the activation patterns (onset and magnitude) of the abdominal muscles during a standing long jump using wire and surface electromyography. Activation patterns of the abdominal muscles, especially the deep muscles such as the transversus abdominis (TrA), have yet to be examined during full-body movements such as jumping. Thirteen healthy men participated. Wire electrodes were inserted into the TrA with the guidance of ultrasonography, and surface electrodes were attached to the skin overlying the rectus abdominis (RA) and external oblique (EO). Electromyographic signals and video images were recorded while each subject performed a standing long jump. The jump task was divided into 3 phases: preparation, push-off, and float. For each muscle, activation onset relative to the onset of the RA and normalized muscle activation levels (percent maximum voluntary contraction) were analyzed during each phase. Comparisons between muscles and phases were assessed using 2-way analyses of variance. The onset times of the TrA and EO relative to the onset of the RA were -0.13 ? 0.17 seconds and -0.02 ? 0.07 seconds, respectively. Onset of TrA activation was earlier than that of the EO. The activation levels of all 3 muscles were significantly greater during the push-off phase than during the preparation and float phases. Consistent with previously published trunk-perturbation studies in healthy persons, the TrA was activated prior to the RA and EO. Additionally, the highest muscle activation levels were observed during the push-off phase.

  13. Woodland: dynamics of average diameters of coniferous tree stands of the principal forest types

    Directory of Open Access Journals (Sweden)

    R. A. Ziganshin

    2016-08-01

    Full Text Available The analysis of age dynamics of average diameters of deciduous tree stands of different forest types at Highland Khamar-Daban (natural woodland in South-East Baikal Lake region has been done. The aggregate data of average tree, the analysis of age dynamics of average diameters of a deciduous tree stands of stand diameters by age classes, as well as tree stand current periodic and overall average increment are presented and discussed in the paper. Forest management appraisal is done. The most representative forest types have been selected to be analyzed. There were nine of them including three Siberian stone pine Pinus sibirica Du Tour stands, three Siberian fir Abies sibirica Ledeb. stands, one Siberian spruce Picea obovata Ledeb. stand, and two dwarf Siberian pine Pinus pumila (Pallas Regel stands. The whole high-altitude range of mountain taiga has been evaluated. Mathematical and statistic indicators have been calculated for every forest type. Stone pine stands are the largest. Dynamics of mean diameters of forest stands have been examined by dominant species for every forest type. Quite a number of interesting facts have been elicited. Generally, all species have maximal values of periodic annual increment that is typical for young stands, but further decrease of increment is going on differently and connects to the different lifetime of wood species. It is curious that annual increment of the dwarf Siberian pine stands almost does not decrease with aging. As for mean annual increment, it is more stable than periodic annual increment. From the fifth age class (age of stand approaching maturity mean annual increment of cedar stands varies from 0.20 to 0.24 cm per year; from 0.12–0.15 to 0.18–0.21 cm per year – in fir stands; from 0.18 to 0.24 cm per year – in spruce stands; and from 0.02–0.03 to 0.05–0.06 cm per year – in draft pine stands. Mean annual increment of dwarf Siberian pine increases with aging and increment of other

  14. Research on levitation coupled with standing wave levitation and electromagnetic levitation:

    OpenAIRE

    Jiao, Xiao Yang; Li, Xinbo; Liu, GuoJun; Liu, JianFang; Liu, XiaoLun; Lu, Song

    2013-01-01

    In order to solve the problem caused by metal materials' inability to be cooled without contact with other materials after being heated by electromagnetic levitation, a new method is proposed: using a standing wave levitator to levitate the melted metal. The standing wave levitator adopts a concave spherical surface on the emitter and the reflector. Using ANSYS software, the transducer and the standing wave fields were simulated. Based on the simulation, the distribution and the maximum acous...

  15. In Depth Reporting of Perceptions on the Development of Stand Up Comedy in Indonesia

    OpenAIRE

    Trisnawati, Yeni

    2013-01-01

    Stand up comedy sebagai salah satu bentuk hiburan yang dikenal masyarakat luas telah mengalami perkembangan yang pesat. Namun perkembangan tersebut tidak selalu mendapat tanggapan yang baik. Setiap orang memiliki persepsi atau pandangan sendiri-sendiri mengenai suatu hal. Buku ini memaparkan penelitian akan bagaimana Stand up comedy berkembang baik dalam dunia Internasional maupun di Indonesia itu sendiri, serta tentang bagaimana munculnya dua persepsi berbeda terhadap perkembangan Stand Up C...

  16. A Motion Control of a Robotic Walker for Continuous Assistance during Standing, Walking and Seating Operation

    OpenAIRE

    Chugo, Daisuke; Takase, Kunikatsu

    2010-01-01

    In this paper, we develop an active walker system for standing, walking and seating operation continuously which cooperates the developed standing assistance system with safety and stability. For realizing these conditions, our walker coordinates the assisting position cooperating the standing assistance manipulator according to the posture of the patient. Furthermore, our walker adjusts a seating position when the patient sit down which has high risk for falling down. Using our proposed syst...

  17. Southern pine beetle in loblolly pine: simulating within stand interactions using the process model SPBLOBTHIN

    Science.gov (United States)

    Brian Strom; J. R. Meeker; J. Bishir; James Roberds; X. Wan

    2016-01-01

    Pine stand density is a key determinant of damage resulting from attacks by the southern pine beetle (SPB, Dendroctonus frontalis Zimm.). High-density stands of maturing loblolly pine (Pinus taeda L.) are at high risk for losses to SPB, and reducing stand density is the primary tool available to forest managers for preventing and mitigating damage. Field studies are...

  18. Features of secondary birch young stands in low mountain Pokuttya (Ukrainian Carpathian Mts. )

    OpenAIRE

    MILEVSKAYA S.Y.

    2015-01-01

    Forest landscapes of the region during the last 3–5 centuries undergone the profound anthropogenic transformation. Secondary young stands occupy 25% of the total forest area. The problem of derivatives is particularly relevant for the modern forest typology in the Carpathian region. It requires the reflection in its dynamic trends shaping the stands, especially mixed young stands. The aim of our study consisted in getting the knowledge of the structural features of the secondary phytocoenosis...

  19. Application of Lidar remote sensing to the estimation of forest canopy and stand structure

    Science.gov (United States)

    Lefsky, Michael Andrew

    A new remote sensing instrument, SLICER (Scanning Lidar Imager of Canopies by Echo Recovery), has been applied to the problem of remote sensing the canopy and stand structure of two groups of deciduous forests, Tulip Poplar-Oak stands in the vicinity of Annapolis, MD. and bottomland hardwood stands near Williamston, NC. The ability of the SLICER instrument to remotely sense the vertical distribution of canopy structure (Canopy Height Profile), bulk canopy transmittance, and several indices of canopy height has been successfully validated using twelve stands with coincident field and SLICER estimates of canopy structure. Principal components analysis has been applied to canopy height profiles from both field sites, and three significant factors were identified, each closely related to the amount of foliage in a recognizable layer of the forest, either understory, midstory, or overstory. The distribution of canopy structure to these layers is significantly correlated with the size and number of stems supporting them. The same layered structure was shown to apply to both field and SLICER remotely sensed canopy height profiles, and to apply to SLICER remotely sensed canopy profiles from both the bottomland hardwood stands in the coastal plain of North Carolina, and to mesic Tulip-Poplars stands in the upland coastal plain of Maryland. Linear regressions have demonstrated that canopy and stand structure are correlated to both a statistically significant and useful degree. Stand age and stem density is more highly correlated to stand height, while stand basal area and aboveground biomass are more closely related to a new measure of canopy structure, the quadratic mean canopy height. A geometric model of canopy structure has been shown to explain the differing relationships between canopy structure and stand basal area for stands of Eastern Deciduous Forest and Douglas Fir Forest.

  20. Characterization of free-standing InAs quantum membranes by standing wave hard x-ray photoemission spectroscopy

    Science.gov (United States)

    Conti, G.; Nemšák, S.; Kuo, C.-T.; Gehlmann, M.; Conlon, C.; Keqi, A.; Rattanachata, A.; Karslıoǧlu, O.; Mueller, J.; Sethian, J.; Bluhm, H.; Rault, J. E.; Rueff, J. P.; Fang, H.; Javey, A.; Fadley, C. S.

    2018-05-01

    Free-standing nanoribbons of InAs quantum membranes (QMs) transferred onto a (Si/Mo) multilayer mirror substrate are characterized by hard x-ray photoemission spectroscopy (HXPS) and by standing-wave HXPS (SW-HXPS). Information on the chemical composition and on the chemical states of the elements within the nanoribbons was obtained by HXPS and on the quantitative depth profiles by SW-HXPS. By comparing the experimental SW-HXPS rocking curves to x-ray optical calculations, the chemical depth profile of the InAs(QM) and its interfaces were quantitatively derived with ångström precision. We determined that (i) the exposure to air induced the formation of an InAsO4 layer on top of the stoichiometric InAs(QM); (ii) the top interface between the air-side InAsO4 and the InAs(QM) is not sharp, indicating that interdiffusion occurs between these two layers; (iii) the bottom interface between the InAs(QM) and the native oxide SiO2 on top of the (Si/Mo) substrate is abrupt. In addition, the valence band offset (VBO) between the InAs(QM) and the SiO2/(Si/Mo) substrate was determined by HXPS. The value of VBO = 0.2 ± 0.04 eV is in good agreement with literature results obtained by electrical characterization, giving a clear indication of the formation of a well-defined and abrupt InAs/SiO2 heterojunction. We have demonstrated that HXPS and SW-HXPS are non-destructive, powerful methods for characterizing interfaces and for providing chemical depth profiles of nanostructures, quantum membranes, and 2D layered materials.