The WATERMED field experiment: validation of the AATSR LST product with in situ measurements

Science.gov (United States)

Noyes, E.; Soria, G.; Sobrino, J.; Remedios, J.; Llewellyn-Jones, D.; Corlett, G.

The Advanced Along-Track Scanning Radiometer (AATSR) onboard ESA's Envisat Satellite, is the third in a series of a precision radiometers designed to measure Sea Surface Temperature (SST) with accuracies of better than ± 0.3 K (within 1-sigma limit). Since its launch in March 2001, a prototype AATSR Land Surface Temperature (LST) product has been produced for validation purposes only, with the product becoming operational from mid-2004. The (A)ATSR instrument design is unique in that it has both a nadir- and a forward-view, allowing the Earth's surface to be viewed along two different atmospheric path lengths, thus enabling an improved atmospheric correction to be made when retrieving surface temperature. It also uses an innovative and exceptionally stable on-board calibration system for its infrared channels, which, together with actively cooled detectors, gives extremely high radiometric sensitivity and precision. In this presentation, results from a comparison of the prototype LST product with ground-based measurements obtained at the WATERMED (WATer use Efficiency in natural vegetation and agricultural areas by Remote sensing in the MEDiterranean basin) field site near Marrakech, Morocco, are presented. The comparison shows that the AATSR has a positive bias of + 1.5 K, with a standard deviation of 0.7 K, indicating that the product is operating within the target specification (± 2.5 K) over the WATERMED field site. However, several anomalous validation points were observed during the analysis and we will discuss possible reasons for the occurrence of these data, including their coincidence with the presence of an Envisat blanking pulse (indicating the presence of a radar pulse at the time of AATSR pixel integration). Further investigation into this matter is required as previous investigations have always indicated that the presence of a payload radar pulse does not have any effect on (A)ATSR data quality.

NOAA JPSS Visible Infrared Imaging Radiometer Suite (VIIRS) Land Surface Temperature (LST) Environmental Data Record (EDR) from IDPS

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Land Surface Temperature (LST) from the Visible Infrared Imaging Radiometer Suite...

Satellite-derived NDVI, LST, and climatic factors driving the distribution and abundance of Anopheles mosquitoes in a former malarious area in northwest Argentina.

Science.gov (United States)

Dantur Juri, María Julia; Estallo, Elizabet; Almirón, Walter; Santana, Mirta; Sartor, Paolo; Lamfri, Mario; Zaidenberg, Mario

2015-06-01

Distribution and abundance of disease vectors are directly related to climatic conditions and environmental changes. Remote sensing data have been used for monitoring environmental conditions influencing spatial patterns of vector-borne diseases. The aim of this study was to analyze the effect of the Normalized Difference Vegetation Index (NDVI) and Land Surface Temperature (LST) obtained from the Moderate Resolution Imaging Spectroradiometer (MODIS), and climatic factors (temperature, humidity, wind velocity, and accumulated rainfall) on the distribution and abundance of Anopheles species in northwestern Argentina using Poisson regression analyses. Samples were collected from December, 2001 to December, 2005 at three localities, Aguas Blancas, El Oculto and San Ramón de la Nueva Orán. We collected 11,206 adult Anopheles species, with the major abundance observed at El Oculto (59.11%), followed by Aguas Blancas (22.10%) and San Ramón de la Nueva Orán (18.79%). Anopheles pseudopunctipennis was the most abundant species at El Oculto, Anopheles argyritarsis predominated in Aguas Blancas, and Anopheles strodei in San Ramón de la Nueva Orán. Samples were collected throughout the sampling period, with the highest peaks during the spring seasons. LST and mean temperature appear to be the most important variables determining the distribution patterns and major abundance of An. pseudopunctipennis and An. argyritarsis within malarious areas. © 2015 The Society for Vector Ecology.

Impacts of the Three Gorges Project on Local Climate

Science.gov (United States)

Song, Z.; Liang, S.; Feng, L.

2015-12-01

Three Gorges Project (TGP) is the largest hydroelectric project in the world and has led to significant land cover changes in Three Gorges Reservoir Area (TGRA). Since its construction the debates on its environmental and climatic impacts have never stopped, especially after the extreme drought and flood in Yangtze River Basin these years. TGP reached its final impounding water level in 2010. However, studies on systematically monitoring the long-term variations in surface and atmospheric parameters in TGRA are still lacking. In this study, three important surface parameters - surface albedo, land surface temperature (LST) and evapotranspiration (ET) and two climatic parameters - air temperature and precipitation were investigated from 2000 to 2013 by combining multiple remote sensing data and ground measurements. Results showed that along the reservoir albedo decreased significantly as a result of water impounding. Correspondingly, in the same region daytime LST decreased in spring and summer and nighttime LST increased in autumn and winter. In the western region of TGRA, albedo increased due to resettlement and LST also changed. The average ET increased by 20% in TGR but kept stable in the whole TGRA. In contrast to LST, air temperature showed less apparent spatial and temporal variability. Only in the region near the dam air temperature experienced a decrease at daytime and an increase at nighttime. Further analysis demonstrated precipitation revealed no apparent changes in TGRA and the precipitation anomaly in northwest of TGRA may not be connected with TGP. All of the findings provide a more substantial clues of local climate change caused by TGP.

Inversion of Land Surface Temperature (LST Using Terra ASTER Data: A Comparison of Three Algorithms

Directory of Open Access Journals (Sweden)

Milton Isaya Ndossi

2016-12-01

Full Text Available Land Surface Temperature (LST is an important measurement in studies related to the Earth surface’s processes. The Advanced Space-borne Thermal Emission and Reflection Radiometer (ASTER instrument onboard the Terra spacecraft is the currently available Thermal Infrared (TIR imaging sensor with the highest spatial resolution. This study involves the comparison of LSTs inverted from the sensor using the Split Window Algorithm (SWA, the Single Channel Algorithm (SCA and the Planck function. This study has used the National Oceanic and Atmospheric Administration’s (NOAA data to model and compare the results from the three algorithms. The data from the sensor have been processed by the Python programming language in a free and open source software package (QGIS to enable users to make use of the algorithms. The study revealed that the three algorithms are suitable for LST inversion, whereby the Planck function showed the highest level of accuracy, the SWA had moderate level of accuracy and the SCA had the least accuracy. The algorithms produced results with Root Mean Square Errors (RMSE of 2.29 K, 3.77 K and 2.88 K for the Planck function, the SCA and SWA respectively.

Landsat and Local Land Surface Temperatures in a Heterogeneous Terrain Compared to MODIS Values

Directory of Open Access Journals (Sweden)

Gemma Simó

2016-10-01

Full Text Available Land Surface Temperature (LST as provided by remote sensing onboard satellites is a key parameter for a number of applications in Earth System studies, such as numerical modelling or regional estimation of surface energy and water fluxes. In the case of Moderate Resolution Imaging Spectroradiometer (MODIS onboard Terra or Aqua, pixels have resolutions near 1 km 2 , LST values being an average of the real subpixel variability of LST, which can be significant for heterogeneous terrain. Here, we use Landsat 7 LST decametre-scale fields to evaluate the temporal and spatial variability at the kilometre scale and compare the resulting average values to those provided by MODIS for the same observation time, for the very heterogeneous Campus of the University of the Balearic Islands (Mallorca, Western Mediterranean, with an area of about 1 km 2 , for a period between 2014 and 2016. Variations of LST between 10 and 20 K are often found at the sub-kilometre scale. In addition, MODIS values are compared to the ground truth for one point in the Campus, as obtained from a four-component net radiometer, and a bias of 3.2 K was found in addition to a Root Mean Square Error (RMSE of 4.2 K. An indication of a more elaborated local measurement strategy in the Campus is given, using an array of radiometers distributed in the area.

Improving Soil Moisture Estimation with a Dual Ensemble Kalman Smoother by Jointly Assimilating AMSR-E Brightness Temperature and MODIS LST

Directory of Open Access Journals (Sweden)

Weijing Chen

2017-03-01

Full Text Available Uncertainties in model parameters can easily result in systematic differences between model states and observations, which significantly affect the accuracy of soil moisture estimation in data assimilation systems. In this research, a soil moisture assimilation scheme is developed to jointly assimilate AMSR-E (Advanced Microwave Scanning Radiometer-Earth Observing System brightness temperature (TB and MODIS (Moderate Resolution Imaging Spectroradiometer Land Surface Temperature (LST products, which also corrects model bias by simultaneously updating model states and parameters with a dual ensemble Kalman filter (DEnKS. Common Land Model (CoLM and a Radiative Transfer Model (RTM are adopted as model and observation operator, respectively. The assimilation experiment was conducted in Naqu on the Tibet Plateau from 31 May to 27 September 2011. The updated soil temperature at surface obtained by assimilating MODIS LST serving as inputs of RTM is to reduce the differences between the simulated and observed TB, then AMSR-E TB is assimilated to update soil moisture and model parameters. Compared with in situ measurements, the accuracy of soil moisture estimation derived from the assimilation experiment has been tremendously improved at a variety of scales. The updated parameters effectively reduce the states bias of CoLM. The results demonstrate the potential of assimilating AMSR-E TB and MODIS LST to improve the estimation of soil moisture and related parameters. Furthermore, this study indicates that the developed scheme is an effective way to retrieve downscaled soil moisture when assimilating the coarse-scale microwave TB.

Detecting geothermal anomalies and evaluating LST geothermal component by combining thermal remote sensing time series and land surface model data

NARCIS (Netherlands)

Romaguera, M.; Vaughan, R. G.; Ettema, J.; Izquierdo-Verdiguier, E.; Hecker, C. A.; van der Meer, F. D.

This paper explores for the first time the possibilities to use two land surface temperature (LST) time series of different origins (geostationary Meteosat Second Generation satellite data and Noah land surface modelling, LSM), to detect geothermal anomalies and extract the geothermal component of

Detecting geothermal anomalies and evaluating LST geothermal component by combining thermal remote sensing time series and land surface model data

NARCIS (Netherlands)

Romaguera, M.; Vaughan, R. G.; Ettema, J.; Izquierdo-Verdiguier, E.; Hecker, C. A.; van der Meer, F. D.

2017-01-01

This paper explores for the first time the possibilities to use two land surface temperature (LST) time series of different origins (geostationary Meteosat Second Generation satellite data and Noah land surface modelling, LSM), to detect geothermal anomalies and extract the geothermal component of

Development of a Global Evaporative Stress Index Based on Thermal and Microwave LST towards Improved Monitoring of Agricultural Drought

Science.gov (United States)

Hain, C.; Anderson, M. C.; Otkin, J.; Holmes, T. R.; Gao, F.

2017-12-01

This presentation will describe the development of a global agricultural monitoring tool, with a focus on providing early warning of developing vegetation stress for agricultural decision-makers and stakeholders at relatively high spatial resolution (5-km). The tool is based on remotely sensed estimates of evapotranspiration, retrieved via energy balance principals using observations of land surface temperature. The Evaporative Stress Index (ESI) represents anomalies in the ratio of actual-to-potential ET generated with the ALEXI surface energy balance model. The LST inputs to ESI have been shown to provide early warning information about the development of vegetation stress with stress-elevated canopy temperatures observed well before a decrease in greenness is detected in remotely sensed vegetation indices. As a diagnostic indicator of actual ET, the ESI requires no information regarding antecedent precipitation or soil moisture storage capacity - the current available moisture to vegetation is deduced directly from the remotely sensed LST signal. This signal also inherently accounts for both precipitation and non-precipitation related inputs/sinks to the plant-available soil moisture pool (e.g., irrigation) which can modify crop response to rainfall anomalies. Independence from precipitation data is a benefit for global agricultural monitoring applications due to sparseness in existing ground-based precipitation networks, and time delays in public reporting. Several enhancements to the current ESI framework will be addressed as requested from project stakeholders: (a) integration of "all-sky" MW Ka-band LST retrievals to augment "clear-sky" thermal-only ESI in persistently cloudy regions; (b) operational production of ESI Rapid Change Indices which provide important early warning information related to onset of actual vegetation stress; and (c) assessment of ESI as a predictor of global yield anomalies; initial studies have shown the ability of intra

Effects of post-fire wood management strategies on vegetation recovery and land surface temperature (LST) estimated from Landsat images

Science.gov (United States)

Vlassova, Lidia; Pérez-Cabello, Fernando

2016-02-01

The study contributes remote sensing data to the discussion about effects of post-fire wood management strategies on forest regeneration. Land surface temperature (LST) and Normalized Differenced Vegetation Index (NDVI), estimated from Landsat-8 images are used as indicators of Pinus halepensis ecosystem recovery after 2008 fire in areas of three post-fire treatments: (1) salvage logging with wood extraction from the site on skidders in suspended position (SL); (2) snag shredding in situ leaving wood debris in place (SS) performed two years after the event; and (3) non-intervention control areas (CL) where all snags were left standing. Six years after the fire NDVI values ∼0.5 estimated from satellite images and field radiometry indicate considerable vegetation recovery due to efficient regeneration traits developed by the dominant plant species. However, two years after management activities in part of the burnt area, the effect of SL and SS on ecosystem recovery is observed in terms of both LST and NDVI. Statistically significant differences are detected between the intervened areas (SL and SS) and control areas of non-intervention (CL); no difference is registered between zones of different intervention types (SL and SS). CL areas are on average 1 °C cooler and 10% greener than those corresponding to either SL or SS, because of the beneficial effects of burnt wood residuals, which favor forest recovery through (i) enhanced nutrient cycling in soils, (ii) avoidance of soil surface disturbance and mechanical damage of seedlings typical to the managed areas, and (iii) ameliorated microclimate. The results of the study show that in fire-resilient ecosystems, such as P. halepensis forests, NDVI is higher and LST is lower in areas with no management intervention, being an indication of more favorable conditions for vegetation regeneration.

Atmospheric dispersion characteristics of radioactive materials according to the local weather and emission conditions

Energy Technology Data Exchange (ETDEWEB)

An, Hye Yeon; Kang, Yoon Hee; Kim, Yoo Keun [Pusan National University, Busan (Korea, Republic of); Song, Sang Keun [Jeju National University, Jeju (Korea, Republic of)

2016-12-15

This study evaluated the atmospheric dispersion of radioactive material according to local weather conditions and emission conditions. Local weather conditions were defined as 8 patterns that frequently occur around the Kori Nuclear Power Plant and emission conditions were defined as 6 patterns from a combination of emission rates and the total number of particles of the {sup 137}Cs, using the WRF/HYSPLIT modeling system. The highest mean concentration of {sup 137}Cs occurred at 0900 LST under the ME4{sub 1} (main wind direction: SSW, daily average wind speed: 2.8 ms{sup -1}), with a wide region of its high concentration due to the continuous wind changes between 0000 and 0900 LST; under the ME3 (NE, 4.1 ms{sup -1}), the highest mean concentration of {sup 137}Cs occurred at 1500 and 2100 LST with a narrow dispersion along a strong northeasterly wind. In the case of ME4{sub 4} (S, 2.7 ms{sup -1}), the highest mean concentration of {sup 137}Cs occurred at 0300 LST because {sup 137}Cs stayed around the KNPP under low wind speed and low boundary layer height. As for the emission conditions, EM1{sub 3} and EM2{sub 3} that had the maximum total number of particles showed the widest dispersion of {sup 137}Cs, while its highest mean concentration was estimated under the EM1{sub 1} considering the relatively narrow dispersion and high emission rate. This study showed that even though an area may be located within the same radius around the Kori Nuclear Power Plant, the distribution and levels of {sup 137}Cs concentration vary according to the change in time and space of weather conditions (the altitude of the atmospheric boundary layer, the horizontal and vertical distribution of the local winds, and the precipitation levels), the topography of the regions where {sup 137}Cs is dispersed, the emission rate of {sup 137}Cs, and the number of emitted particles.

Amputations for extremity soft tissue sarcoma in an era of limb salvage treatment : Local control and survival

NARCIS (Netherlands)

Stevenson, Marc G; Musters, Annelie H; Geertzen, Jan H B; van Leeuwen, Barbara L; Hoekstra, Harald J; Been, Lukas B

2018-01-01

BACKGROUND: Despite multimodality limb salvage treatment (LST) for locally advanced extremity soft tissue sarcoma (ESTS), some patients still need an amputation. Indications for amputation and oncological outcome for these patients are described. METHODS: Between 1996 and 2016, all patients who

5 CFR 9901.332 - Standard and targeted local market supplements.

Science.gov (United States)

2010-01-01

... other appropriate factors; (2) A targeted local market supplement applies to an employee eligible for a... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Standard and targeted local market... DEFENSE NATIONAL SECURITY PERSONNEL SYSTEM (NSPS) Pay and Pay Administration Local Market Supplements...

Global corporate workplaces implementing new global workplace standards in a local context

CERN Document Server

Hodulak, Martin

2017-01-01

In recent years, multinational corporations were increasingly engaged in the development of standardized global workplace models. For their implementation and feasibility, it is decisive as how these standards fit the diverse regional workplace cultures. This topic was pursued in the course of a research project, comparing established workplaces in Germany, USA and Japan against global workplace standards of multinational corporations. The analysis confirmed the expected differences among local workplaces and on the other hand a predominant mainstream among global corporate workplace standards. Conspicuous however, are the fundamental differences between local models and corporate standards. For the implementation of global standards in local context, this implies multiple challenges on cultural, organizational and spatial level. The analysis findings provide information for assessing current projects and pinpointing optimization measures. The analysis framework further provides a tool to uncover and assess n...

Below regulatory concern standards: The limits of state and local authority

International Nuclear Information System (INIS)

Silverman, D.J.

1990-01-01

The paper discusses: (1) the scope of the Nuclear Regulatory Commission's authority to develop and implement below regulatory concern or BRC standards; and (2) the limitations on the legal authority of states and local governments to create impediments to full implementation of such standards. The paper demonstrates that the NRC is acting well within its statutory authority in developing BRC regulations and guidelines, and that the ability of state and local governments to impede generators' use of those regulations and guidelines on the basis of legal or regulatory initiatives is substantially circumscribed. While some generators may be reluctant, as a result of political factors, to utilize BRC standards, the decision whether or not to use such standards should not be made without careful consideration of the applicable legal and regulatory limitations on state and local authority

A comparison of radiometric correction techniques in the evaluation of the relationship between LST and NDVI in Landsat imagery.

Science.gov (United States)

Tan, Kok Chooi; Lim, Hwee San; Matjafri, Mohd Zubir; Abdullah, Khiruddin

2012-06-01

Atmospheric corrections for multi-temporal optical satellite images are necessary, especially in change detection analyses, such as normalized difference vegetation index (NDVI) rationing. Abrupt change detection analysis using remote-sensing techniques requires radiometric congruity and atmospheric correction to monitor terrestrial surfaces over time. Two atmospheric correction methods were used for this study: relative radiometric normalization and the simplified method for atmospheric correction (SMAC) in the solar spectrum. A multi-temporal data set consisting of two sets of Landsat images from the period between 1991 and 2002 of Penang Island, Malaysia, was used to compare NDVI maps, which were generated using the proposed atmospheric correction methods. Land surface temperature (LST) was retrieved using ATCOR3_T in PCI Geomatica 10.1 image processing software. Linear regression analysis was utilized to analyze the relationship between NDVI and LST. This study reveals that both of the proposed atmospheric correction methods yielded high accuracy through examination of the linear correlation coefficients. To check for the accuracy of the equation obtained through linear regression analysis for every single satellite image, 20 points were randomly chosen. The results showed that the SMAC method yielded a constant value (in terms of error) to predict the NDVI value from linear regression analysis-derived equation. The errors (average) from both proposed atmospheric correction methods were less than 10%.

Detecting geothermal anomalies and evaluating LST geothermal component by combining thermal remote sensing time series and land surface model data

Science.gov (United States)

Romaguera, Mireia; Vaughan, R. Greg; Ettema, J.; Izquierdo-Verdiguier, E.; Hecker, C. A.; van der Meer, F.D.

2018-01-01

This paper explores for the first time the possibilities to use two land surface temperature (LST) time series of different origins (geostationary Meteosat Second Generation satellite data and Noah land surface modelling, LSM), to detect geothermal anomalies and extract the geothermal component of LST, the LSTgt. We hypothesize that in geothermal areas the LSM time series will underestimate the LST as compared to the remote sensing data, since the former does not account for the geothermal component in its model.In order to extract LSTgt, two approaches of different nature (physical based and data mining) were developed and tested in an area of about 560 × 560 km2 centered at the Kenyan Rift. Pre-dawn data in the study area during the first 45 days of 2012 were analyzed.The results show consistent spatial and temporal LSTgt patterns between the two approaches, and systematic differences of about 2 K. A geothermal area map from surface studies was used to assess LSTgt inside and outside the geothermal boundaries. Spatial means were found to be higher inside the geothermal limits, as well as the relative frequency of occurrence of high LSTgt. Results further show that areas with strong topography can result in anomalously high LSTgt values (false positives), which suggests the need for a slope and aspect correction in the inputs to achieve realistic results in those areas. The uncertainty analysis indicates that large uncertainties of the input parameters may limit detection of LSTgt anomalies. To validate the approaches, higher spatial resolution images from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data over the Olkaria geothermal field were used. An established method to estimate radiant geothermal flux was applied providing values between 9 and 24 W/m2 in the geothermal area, which coincides with the LSTgt flux rates obtained with the proposed approaches.The proposed approaches are a first step in estimating LSTgt

Highly specific and rapid immuno-fluorescent visualization and detection of E. coli O104:H4 with protein-A coated magnetic beads based LST-MUG assay.

Science.gov (United States)

Barizuddin, Syed; Balakrishnan, Baskar; Stringer, R Cody; Dweik, Majed

2015-08-01

A method combining immunomagnetic separation and fluorescent sensing was developed to detect Escherichia coli (E. coli) O104:H4. The antibody specific to E. coli O104:H4 was immobilized on protein A-coated magnetic beads. This protein-A-anti E. coli O104:H4 complex was used to bind Fluorescein IsoThioCyanate (FITC) labeled E. coli O104:H4 antigen (whole cell) on it. The goal was to achieve a fluorescently detectable protein-A-anti E. coli O104:H4-E. coli O104:H4 complex on the magnetic beads. Fluorescent microscopy was used to image the magnetic beads. The resulting fluorescence on the beads was due to the FITC labeled antigen binding on the protein-A-anti E. coli O104:H4 immobilized magnetic beads. This visually proves the antigen-antibody binding. The fluorescent imaging results were obtained in 2 h if the minimum available bacteria in the sample were at least 10(5) CFU/ml. If no fluorescence was observed on the magnetic beads during fluorescent imaging, it indicates the bacterial concentration in the sample to be too low for it to have bound to the magnetic beads and hence no detection was possible. To detect bacterial concentration less than 10(5) CFU/ml in the sample, an additional step was required for detection. The magnetic bead complex was added to the LST-MUG (lauryl sulfate tryptose-4-methylumbelliferyl-β-D-glucuronide), a signaling reporter. The E. coli O104:H4 grows in LST-MUG and releases β-glucuronidase enzyme. This enzyme cleaves the MUG substrate that produces 4-methylumbelliferone, a highly fluorescent species. This fluorescence was detected using a spectrofluorometer. The emission peak in the fluorescent spectrum was found to be at 450 nm. The lower and upper detection range for this LST-MUG assay was found to be 2.05×10(5)-4.09×10(8) CFU/ml. The results for the LST-MUG assay for concentrations below 10(5) CFU/ml were ascertained in 8h. The advantages of this technique include the specific detection of bacteria without an enrichment step and

Consumers’ Perception on Standardized Advertizing and Localized Advertising of Multinational Companies in Smartphone Industry

Directory of Open Access Journals (Sweden)

Ran Liu

2014-10-01

Full Text Available This research analyzed the difference between standardized advertising and localized (adapted advertising based on the perception of consumers from China and the U.S. Both qualitative and quantitative analyses have been using to evaluate different marketing approaches in multiple international markets. The emphasis of this study focuses on evaluating the efficiency of advertising by assessing to what extent a standardized and localized commercial enhances brand preference and consumer’s likelihood to purchase. Quantitative analysis was conducted to identify the significance of the difference between the efficiency of standardized advertising and localized advertising in the smartphone industry, based on the perception of consumers from China and the United States in the smartphone industry. By testing the significance of the hypothesis on ad standardization and localization, some implications are suggested. The results show that it is more effective to implement a standardized ad rather than a localized ad in China.  Although the sample data of this study is collected from China and the U.S., qualitative analysis covers multiple nations from Asia to Europe and has meaningful empirical value for MNCs to develop business in those countries 

Testing of camera performance standards at steady and local overloading

International Nuclear Information System (INIS)

Keszthelyine Landori, S.; Adorjanne Farkas, M.; Csirik, J.

1983-01-01

Camera performance standards are usually given for low count rates and uniform irradiation. A conventional analog gamma camera system (Gamma MB 9100 manufactured under the know-how of Picker DC 4/12 in Hungary) was studied on the basis of the Picker test procedure and the NEMA standard system. Uniformity, linearity, spatial and energy resolution were measured at high count rates and uniform irradiation (steady overloading). Linearity was studied at local overloading. Linearity, spatial and energy resolution were measured by a 1024-channel analyzer-computer system of KFKI, Hungary. The data were evaluated on the basis of NEMA standards, while uniformity was measured by the Gamma data processing system and evaluated by special SEGAMS programs. Performance variations were studied between 7500 cps and 75.000 cps pulse rates. Spatial and energy resolution were influenced strongly, uniformity slightly by pulse rates, while linearity did not change at all. Linearity was not influenced even by local overloading. (author)

Aid conditionalities, international Good Manufacturing Practice standards and local production rights: a case study of local production in Nepal.

Science.gov (United States)

Brhlikova, Petra; Harper, Ian; Subedi, Madhusudan; Bhattarai, Samita; Rawal, Nabin; Pollock, Allyson M

2015-06-14

Local pharmaceutical production has been endorsed by the WHO as a means of addressing health priorities of developing countries. However, local producers of essential medicines must comply with international pharmaceutical standards in order to be eligible to compete in donor tenders. These standards determine production rights for on-patent and off-patent medicines, and guide international procurement of medicines. We reviewed the literature on the impact of Good Manufacturing Practice (GMP) on local production; a gap analysis from the literature review indicated a need for further research. Over sixty interviews were conducted with people involved in the Nepali pharmaceutical production and distribution chain from 2006 to 2009 on the GMP areas of relevance: regulatory capacity, staffing, funding and training, resourcing of GMP, inspectors' interpretation of the rules and compliance. Although Nepal producers have increased their overall share of the domestic market, only the public manufacturer, Royal Drugs, focuses on medicines for public health programmes; private producers engage mainly in brand competition for private markets, not essential medicines. Nepali regulators and producers state that implementation of GMP standards is hindered by low regulatory capacity, insufficient training of staff in the industry, financial constraints and lack of investment for upgrading capital. The transition period to mandatory compliance with WHO GMP rules is lengthy. Less than half of private producers had WHO GMP in 2013. Producers are not directly affected by international harmonisation of standards as they do not export medicines and the Nepali regulator does not enforce the WHO standards strictly. Without an international GMP certificate they cannot tender for donor dependent health programmes. In Nepal, local private manufacturers focus mainly on brand competition for private consumption not essential medicines, the government preferentially procures essential

Leishmania OligoC-TesT as a simple, rapid, and standardized tool for molecular diagnosis of cutaneous leishmaniasis in Peru.

Science.gov (United States)

Espinosa, Diego; Boggild, Andrea K; Deborggraeve, Stijn; Laurent, Thierry; Valencia, Cristian; Pacheco, Rosa; Miranda-Verástegui, César; Llanos-Cuentas, Alejandro; Leclipteux, Thierry; Dujardin, Jean-Claude; Büscher, Philippe; Arévalo, Jorge

2009-08-01

Molecular methods such as PCR have become attractive tools for diagnosis of cutaneous leishmaniasis (CL), both for their high sensitivity and for their specificity. However, their practical use in routine diagnosis is limited due to the infrastructural requirements and the lack of any standardization. Recently, a simplified and standardized PCR format for molecular detection of Leishmania was developed. The Leishmania OligoC-TesT is based on simple and rapid detection using a dipstick with PCR-amplified Leishmania DNA. In this study, we estimated the diagnostic accuracy of the Leishmania OligoC-TesT for 61 specimens from 44 CL-suspected patients presenting at the leishmaniasis clinic of the Instituto de Medicina Tropical Alexander von Humboldt, Peru. On the basis of parasitological detection and the leishmanin skin test (LST), patients were classified as (i) confirmed CL cases, (ii) LST-positive cases, and (iii) LST-negative cases. The sensitivities of the Leishmania OligoC-TesT was 74% (95% confidence interval (CI), 60.5% to 84.1%) for lesion aspirates and 92% (95% CI, 81.2% to 96.9%) for scrapings. A significantly higher sensitivity was observed with a conventional PCR targeting the kinetoplast DNA on the aspirates (94%) (P = 0.001), while there was no significant difference in sensitivity for the lesion scrapings (88%) (P = 0.317). In addition, the Leishmania OligoC-TesT was evaluated for 13 CL-suspected patients in two different peripheral health centers in the central jungle of Peru. Our findings clearly indicate the high accuracy of the Leishmania OligoC-TesT for lesion scrapings for simple and rapid molecular diagnosis of CL in Peru.

Leishmania OligoC-TesT as a Simple, Rapid, and Standardized Tool for Molecular Diagnosis of Cutaneous Leishmaniasis in Peru▿

Science.gov (United States)

Espinosa, Diego; Boggild, Andrea K.; Deborggraeve, Stijn; Laurent, Thierry; Valencia, Cristian; Pacheco, Rosa; Miranda-Verástegui, César; Llanos-Cuentas, Alejandro; Leclipteux, Thierry; Dujardin, Jean-Claude; Büscher, Philippe; Arévalo, Jorge

2009-01-01

Molecular methods such as PCR have become attractive tools for diagnosis of cutaneous leishmaniasis (CL), both for their high sensitivity and for their specificity. However, their practical use in routine diagnosis is limited due to the infrastructural requirements and the lack of any standardization. Recently, a simplified and standardized PCR format for molecular detection of Leishmania was developed. The Leishmania OligoC-TesT is based on simple and rapid detection using a dipstick with PCR-amplified Leishmania DNA. In this study, we estimated the diagnostic accuracy of the Leishmania OligoC-TesT for 61 specimens from 44 CL-suspected patients presenting at the leishmaniasis clinic of the Instituto de Medicina Tropical Alexander von Humboldt, Peru. On the basis of parasitological detection and the leishmanin skin test (LST), patients were classified as (i) confirmed CL cases, (ii) LST-positive cases, and (iii) LST-negative cases. The sensitivities of the Leishmania OligoC-TesT was 74% (95% confidence interval (CI), 60.5% to 84.1%) for lesion aspirates and 92% (95% CI, 81.2% to 96.9%) for scrapings. A significantly higher sensitivity was observed with a conventional PCR targeting the kinetoplast DNA on the aspirates (94%) (P = 0.001), while there was no significant difference in sensitivity for the lesion scrapings (88%) (P = 0.317). In addition, the Leishmania OligoC-TesT was evaluated for 13 CL-suspected patients in two different peripheral health centers in the central jungle of Peru. Our findings clearly indicate the high accuracy of the Leishmania OligoC-TesT for lesion scrapings for simple and rapid molecular diagnosis of CL in Peru. PMID:19553579

Novel hydrophilic nanostructured microtexture on direct metal laser sintered Ti-6Al-4V surfaces enhances osteoblast response in vitro and osseointegration in a rabbit model.

Science.gov (United States)

Hyzy, Sharon L; Cheng, Alice; Cohen, David J; Yatzkaier, Gustavo; Whitehead, Alexander J; Clohessy, Ryan M; Gittens, Rolando A; Boyan, Barbara D; Schwartz, Zvi

2016-08-01

The purpose of this study was to compare the biological effects in vivo of hierarchical surface roughness on laser sintered titanium-aluminum-vanadium (Ti-6Al-4V) implants to those of conventionally machined implants on osteoblast response in vitro and osseointegration. Laser sintered disks were fabricated to have micro-/nano-roughness and wettability. Control disks were computer numerical control (CNC) milled and then polished to be smooth (CNC-M). Laser sintered disks were polished smooth (LST-M), grit blasted (LST-B), or blasted and acid etched (LST-BE). LST-BE implants or implants manufactured by CNC milling and grit blasted (CNC-B) were implanted in the femurs of male New Zealand white rabbits. Most osteoblast differentiation markers and local factors were enhanced on rough LST-B and LST-BE surfaces in comparison to smooth CNC-M or LST-M surfaces for MG63 and normal human osteoblast cells. To determine if LST-BE implants were osteogenic in vivo, we compared them to implant surfaces used clinically. LST-BE implants had a unique surface with combined micro-/nano-roughness and higher wettability than conventional CNC-B implants. Histomorphometric analysis demonstrated a significant improvement in cortical bone-implant contact of LST-BE implants compared to CNC-B implants after 3 and 6 weeks. However, mechanical testing revealed no differences between implant pullout forces at those time points. LST surfaces enhanced osteoblast differentiation and production of local factors in vitro and improved the osseointegration process in vivo. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2086-2098, 2016. © 2016 Wiley Periodicals, Inc.

Catalyzing alignment processes - Impacts of local adaptations of EMS standards in Thailand

DEFF Research Database (Denmark)

Jørgensen, Ulrik; Lauridsen, Erik Hagelskjær

2004-01-01

ISO14000 as an EMS can be followed as a travelling standard that has to be adapted and domesticated in the local context, where it is applied. By following the processes of this adaptation and how it changes the coherence between the companies, the regulators and other stakeholders the role...... of the standard is identified. The article is based on a number of case-studies of implementation of EMS in Thai companies....

Association of localized hypersensitivity and in-stent neoatherosclerosis with the very late drug-eluting stent thrombosis.

Directory of Open Access Journals (Sweden)

Kyohei Yamaji

Full Text Available Localized hypersensitivity reaction, delayed arterial healing, and neoatherosclerosis inside the stent have been suggested as the underlying pathologic mechanisms of very late stent thrombosis (VLST of drug-eluting stent (DES. The present study sought to explore the prevalence of inflammatory cell infiltrates and evidence for fragments of atherosclerotic plaques in the aspirated thrombi in patients with DES VLST.From April 2004 to September 2012, 48 patients with stent thrombosis (ST of DES underwent thrombus aspiration with retrieved material sufficient for the histopathologic analysis; early ST (EST, within 30 days: N = 17, late ST (LST, between 31 and 365 days: N = 7, and very late ST (VLST, >1 year: N = 24. Eosinophil fraction in the aspirated thrombi was significantly higher in patients with VLST (8.2±5.7% as compared with those with EST (4.3±3.0% and LST (5.5±3.8% (P = 0.03. Eosinophil fraction in the aspirated thrombi was significantly higher in 12 VLST patients with angiographic peri-stent contrast staining (PSS and/or incomplete stent apposition (ISA by intravascular ultrasound than in 12 VLST patients without PSS or ISA (10.6±6.1% versus 5.8±4.1%, P = 0.03. Evidences for fragments of atherosclerotic plaques in the aspirated thrombi were observed only in 3 (13% out of 24 patients with DES VLST.Eosinophil fraction in the aspirated thrombi was significantly higher in patients with DES VLST as compared with those with EST and LST. Evidences for fragments of atherosclerotic plaques were relatively uncommon in patients with DES VLST.

Spatiotemporal Patterns of Ice Mass Variations and the Local Climatic Factors in the Riparian Zone of Central Valley, California

Science.gov (United States)

Inamdar, P.; Ambinakudige, S.

2016-12-01

Californian icefields are natural basins of fresh water. They provide irrigation water to the farms in the central valley. We analyzed the ice mass loss rates, air temperature and land surface temperature (LST) in Sacramento and San Joaquin basins in California. The digital elevation models from Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) were used to calculate ice mass loss rate between the years 2002 and 2015. Additionally, Landsat TIR data were used to extract the land surface temperature. Data from local weather stations were analyzed to understand the spatiotemporal trends in air temperature. The results showed an overall mass recession of -0.8 ± 0.7 m w.e.a-1. We also noticed an about 60% loss in areal extent of the glaciers in the study basins between 2000 and 2015. Local climatic factors, along with the global climate patterns might have influenced the negative trends in the ice mass loss. Overall, there was an increase in the air temperature by 0.07± 0.02 °C in the central valley between 2000 and 2015. Furthermore, LST increased by 0.34 ± 0.4 °C and 0.55± 0.1 °C in the Sacramento and San Joaquin basins. Our preliminary results show the decrease in area and mass of ice mass in the basins, and changing agricultural practices in the valley.

The adoption of ‘International Accounting Standard (IAS) 12 Income Taxes’: Convergence or divergence with local accounting standards in selected ASEAN countries?

OpenAIRE

Prem W.S. Yapa; Diane Kraal; Mahesh Joshi

2015-01-01

This article concerns inter-disciplinary research on questions about the socio-economic impact of the adoption and convergence of International Financial Reporting Standards (IFRS) with local standards in selected countries. The article approaches the research in two stages. The first stage concerns the findings and analysis relating to the general impact of the IFRS standards on Singapore and Malaysia. Findings reveal that respondents expressed reservations about cited IFRS adoption benefits...

[Consequences for labile blood products of leukocyte depletion by whole blood filtration using the Leucoflex LST1 in-line filter. Evaluation of the Leucoflex LST1 filter].

Science.gov (United States)

Janus, G; Samson, T; Faudon, R; Renaudeau, C; Joussemet, M; Fabre, G

1997-12-01

The aim of this study is to evaluate the effects of whole blood filtration after a storage time of 20-24 hours at laboratory temperature using the in line filter Leucoflex LST1. The study concerns 49 blood donations in which we studied leukocyte depletion, proteins (IgG, IgA, IgM, haptoglobin, C3, C4), coagulation factors (fibrinogen, factors XII, XI, IX, VIII, V, proteins S and C, plasminogen, tPA, D-Dimers, PDF) at day 1, the parameters of conservation (ATP, 2-3 DPG, extra cellular potassium, haemolysis, pH) of red blood cell concentrates (RCCs) and bacteriological sterility at day 1 and 42. Despite a correct leukocyte depletion (mean depletion of 3.96 log), a 10 fold higher mean level of residual leukocytes/unit than with buffy coat poor RCC filtration (0.514.10(6) vs 0.051.10(6)) is observed. Moreover a lot of concentrates are not in accordance with French regulations (7/42 with more than 1.10(6) leukocytes/unit). The variation of the rates of IgG, IgA, IgM, haptoglobin, C4 and protein C is not significant. For the others there is a slight decrease with a mean level remaining in a physiological range. No sign of activation is noted. The sterility assays remain negative and the RCC conservation is not altered. In conclusion, even if the quality of the leukocyte depletion is not satisfactory in our study and has to be stated more precisely by multicenter studies, the whole blood filtration does not alter the quality of the derived components and allows us obtain RCC in a bigger volume and containing more haemoglobin than with the classical procedure after removing the buffy-coat [10].

Impact of land cover and population density on land surface temperature: case study in Wuhan, China

Science.gov (United States)

Li, Lin; Tan, Yongbin; Ying, Shen; Yu, Zhonghai; Li, Zhen; Lan, Honghao

2014-01-01

With the rapid development of urbanization, the standard of living has improved, but changes to the city thermal environment have become more serious. Population urbanization is a driving force of residential expansion, which predominantly influences the land surface temperature (LST). We obtained the land covers and LST maps of Wuhan from Landsat-5 images in 2000, 2002, 2005, and 2009, and discussed the distribution of land use/cover change and LST variation, and we analyzed the correlation between population distribution and LST values in residential regions. The results indicated massive variation of land cover types, which was shown as a reduction in cultivatable land and the expansion of building regions. High-LST regions concentrated on the residential and industrial areas with low vegetation coverage. In the residential region, the population density (PD) had effects on the LST values. Although the area or variation of residential regions was close, lower PD was associated with lower mean LST or LST variation. Thus, decreasing the high-LST regions concentration by reducing the PD may alleviate the urban heat island effect on the residential area. Taken together, these results can provide supports for urban planning projects and studies on city ecological environments.

20 CFR 1001.123 - Performance standards governing the assignment and role of Local Veterans' Employment...

Science.gov (United States)

2010-04-01

... assignment and role of Local Veterans' Employment Representatives (LVERs). 1001.123 Section 1001.123... Veterans and Eligible Persons § 1001.123 Performance standards governing the assignment and role of Local... one member of each State agency staff, preferably an eligible veteran, shall be designated and...

Backpropagation Neural Ensemble for Localizing and Recognizing Non-Standardized Malaysia’s Car Plates

OpenAIRE

Chin Kim On; Teo Kein Yau; Rayner Alfred; Jason Teo; Patricia Anthony; Wang Cheng

2016-01-01

In this paper, we describe a research project that autonomously localizes and recognizes non-standardized Malaysian’s car plates using conventional Backpropagation algorithm (BPP) in combination with Ensemble Neural Network (ENN). We compared the results with the results obtained using simple Feed-Forward Neural Network (FFNN). This research aims to solve four main issues; (1) localization of car plates that has the same colour with the vehicle colour, (2) detection and recognition of car pla...

Local radiodiagnostics standards - the way to make fortune?

International Nuclear Information System (INIS)

Borek, P.

2009-01-01

An issue of local radiodiagnostics standards (LRS), the must for all workplaces practising x- ray diagnostics, has reached a next level of its life. While between 2004 and 2007 many workplaces were refusing introduction of LRS mainly due to the non-existence of the so called national radiodiagnostics standards (NRS) in 2008 some of these workplaces change their point of view and instead of waiting for publication of the NRS in the bulletin of the Ministry of Health they begin to work on their LRS not only to comply with the requirements of paragraph 63 para 1 regulation No. 307 /2002 Coll., on radiation protection. Some workplaces decided to cope with LRS by outscoring. The VF ,a.s. company is probably the first on the market with LRS tailored to fit the practice of the X-ray workplaces. The VF company takes the opportunity to deliver a presentation that covers its experience with supplying of LRS depicting the whole range of work a supplier may offer to the X-ray workplace. At the end of the presentation the question whether it is possible to make fortune on LRS is discussed. (author)

Local radiodiagnostics standards - the way to make fortune?

International Nuclear Information System (INIS)

Borek, P.

2008-01-01

An issue of local radiodiagnostics standards (LRS), the must for all workplaces practising x- ray diagnostics, has reached a next level of its life. While between 2004 and 2007 many workplaces were refusing introduction of LRS mainly due to the non-existence of the so called national radiodiagnostics standards (NRS) in 2008 some of these workplaces change their point of view and instead of waiting for publication of the NRS in the bulletin of the Ministry of Health they begin to work on their LRS not only to comply with the requirements of paragraph 63 para 1 regulation No. 307 /2002 Coll., on radiation protection. Some workplaces decided to cope with LRS by outscoring. The VF ,a.s. company is probably the first on the market with LRS tailored to fit the practice of the X-ray workplaces. The VF company takes the opportunity to deliver a presentation that covers its experience with supplying of LRS depicting the whole range of work a supplier may offer to the X-ray workplace. At the end of the presentation the question whether it is possible to make fortune on LRS will be discussed. (full paper) (authors)

Evaluation of China's local enforcement of energy efficiency standards and labeling programs for appliances and equipment

International Nuclear Information System (INIS)

Khanna, Nina Zheng; Zhou, Nan; Fridley, David; Fino-Chen, Cecilia

2013-01-01

Aims: This paper aims to evaluate local enforcement of China's mandatory appliance and equipment energy efficiency standards and labeling programs, two increasingly important policies for meeting national energy and carbon reduction targets. The expected energy savings of efficiency standards and labels can be fully realized only with strong enforcement to ensure compliance for all products sold. This paper provides comprehensive retrospective evaluation of the methodologies, results, progress and remaining challenges in pilot enforcement projects initiated in the absence of consistent national check-testing focused on energy efficiency. Scope: This paper's scope is focused on 2006–2009 pilot local check-tests conducted to verify appliance and equipment compliance with China's mandatory energy label and efficiency standards. Conclusions: This paper finds both improvement and some backsliding in compliance rates over time. Compared to earlier efforts, 2009 check-tests covered a wider regional and product scope but demonstrated greater variation in compliance rates. Labeling display and energy efficiency compliance was generally high across regions and most products, but lower compliance rates were observed in less economically developed regions and for lighting and industrial products. Based on these findings, areas for improvement in local awareness, product sampling methodology, check-testing tools and procedures are identified. - Highlights: • China's mandatory standards and labeling crucial to national energy saving goals. • China's 2006–2009 pilot efficiency check-testing for standards and labeling evaluated. • Wider geographic and product scope in 2009, but greater variation in compliance. • Generally high compliance, but lower rates for less economically developed region. • Local check-test capacity improving but methodological challenges remain

Comparison of two split-window methods for retrieving land surface temperature from MODIS data

Science.gov (United States)

Zhao, Shaohua; Qin, Qiming; Yang, Yonghui; Xiong, Yujiu; Qiu, Guoyu

2009-08-01

Land surface temperature (LST) is a key parameter in environment and earth science study, especially for monitoring drought. The objective of this work is a comparison of two split-window methods: Mao method and Sobrino method, for retrieving LST using MODIS (Moderate-resolution Imaging Spectroradiometer) data in North China Plain. The results show that the max, min and mean errors of Mao method are 1.33K, 1.54K and 0.13K lower than the standard LST product respectively; while those of Sobrino method are 0.73K, 1.46K and 1.50K higher than the standard respectively. Validation of the two methods using LST product based on weather stations shows a good agreement between the standard and Sobrino method, with RMSE of 1.17K, whereas RMSE of Mao method is 1.85K. Finally, the study introduces the Sobmao method, which is based on Sobrino method but simplifies the estimation of atmospheric water vapour content using Mao method. The Sobmao method has almost the same accuracy with Sobrino method. With high accuracy and simplification of water vapour content estimation, the Sobmao method is recommendable in LST inversion for good application in Ningxia region, the northwest China, with mean error of 0.33K and the RMSE value of 0.91K.

Improvement of least-squares collocation error estimates using local GOCE Tzz signal standard deviations

DEFF Research Database (Denmark)

Tscherning, Carl Christian

2015-01-01

outside the data area. On the other hand, a comparison of predicted quantities with observed values show that the error also varies depending on the local data standard deviation. This quantity may be (and has been) estimated using the GOCE second order vertical derivative, Tzz, in the area covered...... by the satellite. The ratio between the nearly constant standard deviations of a predicted quantity (e.g. in a 25° × 25° area) and the standard deviations of Tzz in smaller cells (e.g., 1° × 1°) have been used as a scale factor in order to obtain more realistic error estimates. This procedure has been applied...

Experience with local lymph node assay performance standards using standard radioactivity and nonradioactive cell count measurements.

Science.gov (United States)

Basketter, David; Kolle, Susanne N; Schrage, Arnhild; Honarvar, Naveed; Gamer, Armin O; van Ravenzwaay, Bennard; Landsiedel, Robert

2012-08-01

The local lymph node assay (LLNA) is the preferred test for identification of skin-sensitizing substances by measuring radioactive thymidine incorporation into the lymph node. To facilitate acceptance of nonradioactive variants, validation authorities have published harmonized minimum performance standards (PS) that the alternative endpoint assay must meet. In the present work, these standards were applied to a variant of the LLNA based on lymph node cell counts (LNCC) run in parallel as a control with the standard LLNA with radioactivity measurements, with threshold concentrations (EC3) being determined for the sensitizers. Of the 22 PS chemicals tested in this study, 21 yielded the same results from standard radioactivity and cell count measurements; only 2-mercaptobenzothiazole was positive by LLNA but negative by LNCC. Of the 16 PS positives, 15 were positive by LLNA and 14 by LNCC; methylmethacrylate was not identified as sensitizer by either of the measurements. Two of the six PS negatives tested negative in our study by both LLNA and LNCC. Of the four PS negatives which were positive in our study, chlorobenzene and methyl salicylate were tested at higher concentrations than the published PS, whereas the corresponding concentrations resulted in consistent negative results. Methylmethacrylate and nickel chloride tested positive within the concentration range used for the published PS. The results indicate cell counts and radioactive measurements are in good accordance within the same LLNA using the 22 PS test substances. Comparisons with the published PS results may, however, require balanced analysis rather than a simple checklist approach. Copyright © 2011 John Wiley & Sons, Ltd.

A Framework for Mapping Global Evapotranspiration using 375-m VIIRS LST

Science.gov (United States)

Hain, C.; Anderson, M. C.; Schull, M. A.; Neale, C. M. U.

2017-12-01

As the world's water resources come under increasing tension due to dual stressors of climate change and population growth, accurate knowledge of water consumption through evapotranspiration (ET) over a range in spatial scales will be critical in developing adaptation strategies. Remote sensing methods for monitoring consumptive water use are becoming increasingly important, especially in areas of food insecurity. One method to estimate ET from satellite-based methods, the Atmosphere Land Exchange Inverse (ALEXI) model uses the change in morning land surface temperature to estimate the partitioning of sensible/latent heat fluxes which are then used to estimate daily ET. This presentation will outline several recent enhancements to the ALEXI modeling system, with a focus on global ET and drought monitoring. Until recently, ALEXI has been limited to areas with high resolution temporal sampling of geostationary sensors. The use of geostationary sensors makes global mapping a complicated process, especially for real-time applications, as data from as many as five different sensors are required to be ingested and harmonized to create a global mosaic. However, our research team has developed a new and novel method of using twice-daily observations from polar-orbiting sensors such as MODIS and VIIRS to estimate the mid-morning rise in LST that is used to drive the energy balance estimations within ALEXI. This allows the method to be applied globally using a single sensor rather than a global compositing of all available geostationary data. Other advantages of this new method include the higher spatial resolution provided by MODIS and VIIRS and the increased sampling at high latitudes where oblique view angles limit the utility of geostationary sensors. Improvements to the spatial resolution of the thermal infrared wavelengths on the VIIRS instrument, as compared to MODIS (375-m VIIRS vs. 1-km MODIS), allows for a much higher resolution ALEXI product than has been

Comparisons of Satellite Soil Moisture, an Energy Balance Model Driven by LST Data and Point Measurements

Science.gov (United States)

Laiolo, Paola; Gabellani, Simone; Rudari, Roberto; Boni, Giorgio; Puca, Silvia

2013-04-01

Soil moisture plays a fundamental role in the partitioning of mass and energy fluxes between land surface and atmosphere, thereby influencing climate and weather, and it is important in determining the rainfall-runoff response of catchments; moreover, in hydrological modelling and flood forecasting, a correct definition of moisture conditions is a key factor for accurate predictions. Different sources of information for the estimation of the soil moisture state are currently available: satellite data, point measurements and model predictions. All are affected by intrinsic uncertainty. Among different satellite sensors that can be used for soil moisture estimation three major groups can be distinguished: passive microwave sensors (e.g., SSMI), active sensors (e.g. SAR, Scatterometers), and optical sensors (e.g. Spectroradiometers). The last two families, mainly because of their temporal and spatial resolution seem the most suitable for hydrological applications In this work soil moisture point measurements from 10 sensors in the Italian territory are compared of with the satellite products both from the HSAF project SM-OBS-2, derived from the ASCAT scatterometer, and from ACHAB, an operative energy balance model that assimilate LST data derived from MSG and furnishes daily an evaporative fraction index related to soil moisture content for all the Italian region. Distributed comparison of the ACHAB and SM-OBS-2 on the whole Italian territory are performed too.

Satellite-derived temperature data for monitoring water status in a floodplain forest of the Upper Sabine River, Texas

Science.gov (United States)

Lemon, Mary Grace T.; Allen, Scott T.; Edwards, Brandon L.; King, Sammy L.; Keim, Richard F.

2016-01-01

Decreased water availability due to hydrologic modifications, groundwater withdrawal, and climate change threaten bottomland hardwood (BLH) forest communities. We used satellite-derived (MODIS) land-surface temperature (LST) data to investigate spatial heterogeneity of canopy temperature (an indicator of plant-water status) in a floodplain forest of the upper Sabine River for 2008–2014. High LST pixels were generally further from the river and at higher topographic locations, indicating lower water-availability. Increasing rainfall-derived soil moisture corresponded with decreased heterogeneity of LST between pixels but there was weaker association between Sabine River stage and heterogeneity. Stronger dependence of LST convergence on rainfall rather than river flow suggests that some regions are less hydrologically connected to the river, and vegetation may rely on local precipitation and other contributions to the riparian aquifer to replenish soil moisture. Observed LST variations associated with hydrology encourage further investigation of the utility of this approach for monitoring forest stress, especially with considerations of climate change and continued river management.

Standard forms and entanglement engineering of multimode Gaussian states under local operations

International Nuclear Information System (INIS)

Serafini, Alessio; Adesso, Gerardo

2007-01-01

We investigate the action of local unitary operations on multimode (pure or mixed) Gaussian states and single out the minimal number of locally invariant parameters which completely characterize the covariance matrix of such states. For pure Gaussian states, central resources for continuous-variable quantum information, we investigate separately the parameter reduction due to the additional constraint of global purity, and the one following by the local-unitary freedom. Counting arguments and insights from the phase-space Schmidt decomposition and in general from the framework of symplectic analysis, accompany our description of the standard form of pure n-mode Gaussian states. In particular, we clarify why only in pure states with n ≤ 3 modes all the direct correlations between position and momentum operators can be set to zero by local unitary operations. For any n, the emerging minimal set of parameters contains complete information about all forms of entanglement in the corresponding states. An efficient state engineering scheme (able to encode direct correlations between position and momentum operators as well) is proposed to produce entangled multimode Gaussian resources, its number of optical elements matching the minimal number of locally invariant degrees of freedom of general pure n-mode Gaussian states. Finally, we demonstrate that so-called 'block-diagonal' Gaussian states, without direct correlations between position and momentum, are systematically less entangled, on average, than arbitrary pure Gaussian states

Efficient Linear and Non-Linear Finite Element Formulation using a New Local Enhancement of Displacement Fields for Triangular Elements

DEFF Research Database (Denmark)

Damkilde, Lars; Pedersen, Ronnie

2012-01-01

This paper describes a new triangular plane element which can be considered as a linear strain triangular element (LST) extended with incompatible displacement modes. The extended element will have a full cubic interpolation of strains and stresses. The extended LST-element is connected with other...... elements similar to the LST-element i.e. through three corner nodes and three mid-side nodes. The incompatible modes are associated with two displacement gradients at each mid-side node and displacements in the central node. The element passes the patch test and converges to the exact solution. The element...... often show a very slow convergence, and the numerical solutions will in general overestimate the bearing capacity and underestimate the displacements. The examples show that the extended incompatible element behaves much better than the corresponding compatible elements especially for coarse meshes....

Retrieval of Land Surface Temperature over the Heihe River Basin Using HJ-1B Thermal Infrared Data

Directory of Open Access Journals (Sweden)

Xiaoying Ouyang

2014-12-01

Full Text Available The reliable estimation of spatially distributed Land Surface Temperature (LST is useful for monitoring regional land surface heat fluxes. A single-channel method is developed to derive the LST over the Heihe River Basin in China using data from the infrared sensor (IRS onboard the Chinese “Environmental and Disaster Monitoring and Forecasting with a Small Satellite Constellation” (HJ-1B for short for one of the satellites, with ancillary water vapor information from Moderate Resolution Imaging Spectroradiometer (MODIS products (MOD05 and in situ automatic sun tracking photometer CE318 data for the first time. In situ LST data for the period from mid-June to mid-September 2012 were acquired from automatic meteorological stations (AMS that are part of Heihe Watershed Allied Telemetry Experimental Research (HiWATER project. MOD05-based LST and CE318-based LST are compared with in situ measurements at 16 AMS sites with land cover types of vegetable, maize and orchards. The results show that the use of the MOD05 product could achieve a comparable accuracy in LST retrieval with that achieved using the CE318 data. The largest difference between the MOD05-based LST and CE318-based LST is 0.84 K throughout the study period over the Heihe River Basin. The standard deviation (STD, root mean square error (RMSE, and correlation coefficient (R of HJ-1B/IRS vs. the in situ measurements are 2.45 K, 2.78 K, and 0.67, respectively, whereas those for the MODIS 1 km LST product vs. the in situ measurements are 4.07 K, 2.98 K, and 0.79, respectively. The spatial pattern of the HJ-1B/LST over the study area in the Heihe River Basin generally agreed well with the MODIS 1 km LST product and contained more detailed spatial textures.

AATSR land surface temperature product algorithm verification over a WATERMED site

Science.gov (United States)

Noyes, E. J.; Sòria, G.; Sobrino, J. A.; Remedios, J. J.; Llewellyn-Jones, D. T.; Corlett, G. K.

A new operational Land Surface Temperature (LST) product generated from data acquired by the Advanced Along-Track Scanning Radiometer (AATSR) provides the opportunity to measure LST on a global scale with a spatial resolution of 1 km2. The target accuracy of the product, which utilises nadir data from the AATSR thermal channels at 11 and 12 μm, is 2.5 K for daytime retrievals and 1.0 K at night. We present the results of an experiment where the performance of the algorithm has been assessed for one daytime and one night time overpass occurring over the WATERMED field site near Marrakech, Morocco, on 05 March 2003. Top of atmosphere (TOA) brightness temperatures (BTs) are simulated for 12 pixels from each overpass using a radiative transfer model, with the LST product and independent emissivity values and atmospheric data as inputs. We have estimated the error in the LST product over this biome for this set of conditions by applying the operational AATSR LST retrieval algorithm to the modelled BTs and comparing the results with the original AATSR LSTs input into the model. An average bias of -1.00 K (standard deviation 0.07 K) for the daytime data, and -1.74 K (standard deviation 0.02 K) for the night time data is obtained, which indicates that the algorithm is yielding an LST that is too cold under these conditions. While these results are within specification for daytime retrievals, this suggests that the target accuracy of 1.0 K at night is not being met within this biome.

Living Traditions--A Teacher's Guide: Teaching Local History Using State and National Learning Standards.

Science.gov (United States)

Skelding, Mark; Kemple, Martin; Kiefer, Joseph

This guide is designed to take teachers through a step-by-step process for developing an integrated, standards-based curriculum that focuses on the stories, history, folkways, and agrarian traditions of the local community. Such a place-based curriculum helps students to become culturally literate, makes learning relevant and engaging, draws on…

The adoption of ‘International Accounting Standard (IAS 12 Income Taxes’: Convergence or divergence with local accounting standards in selected ASEAN countries?

Directory of Open Access Journals (Sweden)

Prem W.S. Yapa

2015-09-01

Full Text Available This article concerns inter-disciplinary research on questions about the socio-economic impact of the adoption and convergence of International Financial Reporting Standards (IFRS with local standards in selected countries. The article approaches the research in two stages. The first stage concerns the findings and analysis relating to the general impact of the IFRS standards on Singapore and Malaysia. Findings reveal that respondents expressed reservations about cited IFRS adoption benefits, including increases of foreign investment and equity cost reductions; and stakeholder confidence has been eroded by the complex harmonising of principles-based ‘fair value’ requirements. Debate continues on the application of IFRS regarding standards on financial instruments, real estate and agriculture. Our qualitative research methodology of survey uses institutional theory and stakeholder theory for analysis. The second stage posits further research for IAS12 Income Taxes, given accounting standards are one starting point for tax compliance, and that income taxes form part of financial statements. A test questionnaire was prepared and industry respondents were asked questions on the extent of IAS12’s challenges to practitioners in Australia.

Thrombectomy approach using pediatric Foley catheter in lateral sinus thrombosis developed as a complication of chronic otitis media in a patient with sickle cell anemia

Directory of Open Access Journals (Sweden)

Ercan Akbay

2014-04-01

Full Text Available Lateral sinus thrombophlebitis (LST is a rarely seen intracranial complication of chronic otitis media. Even single case report may guide in this entity given the lack of larger series. In the present manuscript, we will discuss removal of infected thrombus localized in transverse sinus via Foley catheter in a 46-years old man with sickle cell anemia underwent surgery due to LST.

Status of Land Surface Temperature Product Development at NOAA/NESDIS/STAR for JPSS and GOES-R Missions

Science.gov (United States)

Yu, Yunyue; Liu, yuling; yu, peng; Casiszar, Ivan; Zhou, Lihang

2016-04-01

Land surface temperature (LST) is of fundamental importance to many aspects of the geosciences, e.g., net radiation budget at the Earth surface, monitoring state of crops and vegetation, as well as an important indicator of both the greenhouse effect and the physics of land-surface processes at local through global scales. Satellite LST measurements provide unique data sources for regional and global coverage in fairly good temporal, spatial resolution and time span. Therefore, LST is one of baseline products in both JPSS and GOES-R satellite missions. The Center for SaTellite Applications and Research (STAR) of NOAA/NESDIS is responsible for developing high quality LST products for a variety of satellite missions including JPSS and GOES-R. The JPSS LST data, which is produced for each swath of observations, has reached its beta, provisional and validated stage 1 status in October 2013, May 2014, and December 2015, respectively. A routine validation and monitoring toolkit has been developed and its results are available through a public web site. Our validation results against the U.S. SURFRAD ground stations show that uncertainty of the VIIRS LST is less than 2.35K (vs. the JPSS mission requirement of 2.5K). Improvement of the JPSS LST product is on-going, which counts surface emissive variation explicitly in retrieval algorithm. Further, a gridded daily global LST product will be available by end of 2016. In terms of the GOES-R LST product, we have evaluated the retrieval algorithm using SEVIRI and AHI data as proxies. The evaluation results show that the accuracy of GOES-R LST is expected to be less than 2.30K (GOES-R mission requirement). The validation toolkit developed for JPSS mission will be extended and applicable for the GOES-R mission as well. A detailed Readiness, Implementation and Management Plan (RIMP) of GOES-R LST beta and provisional validation has been developed for the GOES-R launch that is scheduled in October 2016.

Image contrast enhancement based on a local standard deviation model

International Nuclear Information System (INIS)

Chang, Dah-Chung; Wu, Wen-Rong

1996-01-01

The adaptive contrast enhancement (ACE) algorithm is a widely used image enhancement method, which needs a contrast gain to adjust high frequency components of an image. In the literature, the gain is usually inversely proportional to the local standard deviation (LSD) or is a constant. But these cause two problems in practical applications, i.e., noise overenhancement and ringing artifact. In this paper a new gain is developed based on Hunt's Gaussian image model to prevent the two defects. The new gain is a nonlinear function of LSD and has the desired characteristic emphasizing the LSD regions in which details are concentrated. We have applied the new ACE algorithm to chest x-ray images and the simulations show the effectiveness of the proposed algorithm

Asynchronous transfer mode and Local Area Network emulation standards, protocols, and security implications

OpenAIRE

Kirwin, John P.

1999-01-01

A complex networking technology called Asynchronous Transfer Mode (ATM) and a networking protocol called Local Area Network Emulation (LANE) are being integrated into many naval networks without any security-driven naval configuration guidelines. No single publication is available that describes security issues of data delivery and signaling relating to the transition of Ethernet to LANE and ATM. The thesis' focus is to provide: (1) an overview and security analysis of standardized protocols ...

A Spatio-Temporal Analysis of the Relationship Between Near-Surface Air Temperature and Satellite Land Surface Temperatures Using 17 Years of Data from the ATSR Series

Science.gov (United States)

Ghent, D.; Good, E.; Bulgin, C.; Remedios, J. J.

2017-12-01

Surface temperatures (ST) over land have traditionally been measured at weather stations. There are many parts of the globe with very few stations, e.g. across much of Africa, leading to gaps in ST datasets, affecting our understanding of how ST is changing, and the impacts of extreme events. Satellites can provide global ST data but these observations represent how hot the land ST (LST; including the uppermost parts of e.g. trees, buildings) is to touch, whereas stations measure the air temperature just above the surface (T2m). Satellite LST data may only be available in cloud-free conditions and data records are frequently climate studies. In this study, the relationship between clear-sky satellite LST and all-sky T2m is characterised in space and time using >17 years of data. The analysis uses a new monthly LST climate data record (CDR) based on the Along-Track Scanning Radiometer (ATSR) series, which has been produced within the European Space Agency GlobTemperature project. The results demonstrate the dependency of the global LST-T2m differences on location, land cover, vegetation and elevation. LSTnight ( 10 pm local solar time) is found to be closely coupled with minimum T2m (Tmin) and the two temperatures generally consistent to within ±5 °C (global median LSTnight- Tmin= 1.8 °C, interquartile range = 3.8 °C). The LSTday ( 10 am local time)-maximum T2m (Tmax) variability is higher because LST is strongly influenced by insolation and surface regime (global median LSTday-Tmax= -0.1 °C, interquartile range = 8.1 °C). Correlations for both temperature pairs are typically >0.9 outside of the tropics. A crucial aspect of this study is a comparison between the monthly global anomaly time series of LST and CRUTEM4 T2m. The time series agree remarkably well, with a correlation of 0.9 and 90% of the CDR anomalies falling within the T2m 95% confidence limits (see figure). This analysis provides independent verification of the 1995-2012 T2m anomaly time series

Quantifying Surface Energy Flux Estimation Uncertainty Using Land Surface Temperature Observations

Science.gov (United States)

French, A. N.; Hunsaker, D.; Thorp, K.; Bronson, K. F.

2015-12-01

Remote sensing with thermal infrared is widely recognized as good way to estimate surface heat fluxes, map crop water use, and detect water-stressed vegetation. When combined with net radiation and soil heat flux data, observations of sensible heat fluxes derived from surface temperatures (LST) are indicative of instantaneous evapotranspiration (ET). There are, however, substantial reasons LST data may not provide the best way to estimate of ET. For example, it is well known that observations and models of LST, air temperature, or estimates of transport resistances may be so inaccurate that physically based model nevertheless yield non-meaningful results. Furthermore, using visible and near infrared remote sensing observations collected at the same time as LST often yield physically plausible results because they are constrained by less dynamic surface conditions such as green fractional cover. Although sensitivity studies exist that help identify likely sources of error and uncertainty, ET studies typically do not provide a way to assess the relative importance of modeling ET with and without LST inputs. To better quantify model benefits and degradations due to LST observational inaccuracies, a Bayesian uncertainty study was undertaken using data collected in remote sensing experiments at Maricopa, Arizona. Visible, near infrared and thermal infrared data were obtained from an airborne platform. The prior probability distribution of ET estimates were modeled using fractional cover, local weather data and a Penman-Monteith mode, while the likelihood of LST data was modeled from a two-source energy balance model. Thus the posterior probabilities of ET represented the value added by using LST data. Results from an ET study over cotton grown in 2014 and 2015 showed significantly reduced ET confidence intervals when LST data were incorporated.

A spatiotemporal analysis of the relationship between near-surface air temperature and satellite land surface temperatures using 17 years of data from the ATSR series

Science.gov (United States)

Good, Elizabeth J.; Ghent, Darren J.; Bulgin, Claire E.; Remedios, John J.

2017-09-01

The relationship between satellite land surface temperature (LST) and ground-based observations of 2 m air temperature (T2m) is characterized in space and time using >17 years of data. The analysis uses a new monthly LST climate data record (CDR) based on the Along-Track Scanning Radiometer series, which has been produced within the European Space Agency GlobTemperature project (http://www.globtemperature.info/). Global LST-T2m differences are analyzed with respect to location, land cover, vegetation fraction, and elevation, all of which are found to be important influencing factors. LSTnight ( 10 P.M. local solar time, clear-sky only) is found to be closely coupled with minimum T2m (Tmin, all-sky) and the two temperatures generally consistent to within ±5°C (global median LSTnight-Tmin = 1.8°C, interquartile range = 3.8°C). The LSTday ( 10 A.M. local solar time, clear-sky only)-maximum T2m (Tmax, all-sky) variability is higher (global median LSTday-Tmax = -0.1°C, interquartile range = 8.1°C) because LST is strongly influenced by insolation and surface regime. Correlations for both temperature pairs are typically >0.9 outside of the tropics. The monthly global and regional anomaly time series of LST and T2m—which are completely independent data sets—compare remarkably well. The correlation between the data sets is 0.9 for the globe with 90% of the CDR anomalies falling within the T2m 95% confidence limits. The results presented in this study present a justification for increasing use of satellite LST data in climate and weather science, both as an independent variable, and to augment T2m data acquired at meteorological stations.

Local network assessment

Science.gov (United States)

Glen, D. V.

1985-04-01

Local networks, related standards activities of the Institute of Electrical and Electronics Engineers the American National Standards Institute and other elements are presented. These elements include: (1) technology choices such as topology, transmission media, and access protocols; (2) descriptions of standards for the 802 local area networks (LAN's); high speed local networks (HSLN's) and military specification local networks; and (3) intra- and internetworking using bridges and gateways with protocols Interconnection (OSI) reference model. The convergence of LAN/PBX technology is also described.

Tests of local Lorentz invariance violation of gravity in the standard model extension with pulsars.

Science.gov (United States)

Shao, Lijing

2014-03-21

The standard model extension is an effective field theory introducing all possible Lorentz-violating (LV) operators to the standard model and general relativity (GR). In the pure-gravity sector of minimal standard model extension, nine coefficients describe dominant observable deviations from GR. We systematically implemented 27 tests from 13 pulsar systems to tightly constrain eight linear combinations of these coefficients with extensive Monte Carlo simulations. It constitutes the first detailed and systematic test of the pure-gravity sector of minimal standard model extension with the state-of-the-art pulsar observations. No deviation from GR was detected. The limits of LV coefficients are expressed in the canonical Sun-centered celestial-equatorial frame for the convenience of further studies. They are all improved by significant factors of tens to hundreds with existing ones. As a consequence, Einstein's equivalence principle is verified substantially further by pulsar experiments in terms of local Lorentz invariance in gravity.

An Analysis of the Discrepancies between MODIS and INSAT-3D LSTs in High Temperatures

Directory of Open Access Journals (Sweden)

Seyed Kazem Alavipanah

2017-04-01

Full Text Available In many disciplines, knowledge on the accuracy of Land Surface Temperature (LST as an input is of great importance. One of the most efficient methods in LST evaluation is cross validation. Well-documented and validated polar satellites with a high spatial resolution can be used as references for validating geostationary LST products. This study attempted to investigate the discrepancies between a Moderate Resolution Imaging Spectro-radiometer (MODIS and Indian National Satellite (INSAT-3D LSTs for high temperatures, focusing on six deserts with sand dune land cover in the Middle East from 3 March 2015 to 24 August 2016. Firstly, the variability of LSTs in the deserts of the study area was analyzed by comparing the mean, Standard Deviation (STD, skewness, minimum, and maximum criteria for each observation time. The mean value of the LST observations indicated that the MYD-D observation times are closer to those of diurnal maximum and minimum LSTs. At all times, the LST observations exhibited a negative skewness and the STD indicated higher variability during times of MOD-D. The observed maximum LSTs from MODIS collection 6 showed higher values in comparison with the last versions of LSTs for hot spot regions around the world. After the temporal, spatial, and geometrical matching of LST products, the mean of the MODIS—INSAT LST differences was calculated for the study area. The results demonstrated that discrepancies increased with temperature up to +15.5 K. The slopes of the mean differences were relatively similar for all deserts except for An Nafud, suggesting an effect of View Zenith Angle (VZA. For modeling the discrepancies between two sensors in continuous space, the Diurnal Temperature Cycles (DTC of both sensors were constructed and compared. The sample DTC models approved the results from discrete LST subtractions and proposed the uncertainties within MODIS DTCs. The authors proposed that the observed LST discrepancies in high

Accounting for both local aquatic community composition and bioavailability in setting site-specific quality standards for zinc.

Science.gov (United States)

Peters, Adam; Simpson, Peter; Moccia, Alessandra

2014-01-01

Recent years have seen considerable improvement in water quality standards (QS) for metals by taking account of the effect of local water chemistry conditions on their bioavailability. We describe preliminary efforts to further refine water quality standards, by taking account of the composition of the local ecological community (the ultimate protection objective) in addition to bioavailability. Relevance of QS to the local ecological community is critical as it is important to minimise instances where quality classification using QS does not reconcile with a quality classification based on an assessment of the composition of the local ecology (e.g. using benthic macroinvertebrate quality assessment metrics such as River InVertebrate Prediction and Classification System (RIVPACS)), particularly where ecology is assessed to be at good or better status, whilst chemical quality is determined to be failing relevant standards. The alternative approach outlined here describes a method to derive a site-specific species sensitivity distribution (SSD) based on the ecological community which is expected to be present at the site in the absence of anthropogenic pressures (reference conditions). The method combines a conventional laboratory ecotoxicity dataset normalised for bioavailability with field measurements of the response of benthic macroinvertebrate abundance to chemical exposure. Site-specific QSref are then derived from the 5%ile of this SSD. Using this method, site QSref have been derived for zinc in an area impacted by historic mining activities. Application of QSref can result in greater agreement between chemical and ecological metrics of environmental quality compared with the use of either conventional (QScon) or bioavailability-based QS (QSbio). In addition to zinc, the approach is likely to be applicable to other metals and possibly other types of chemical stressors (e.g. pesticides). However, the methodology for deriving site-specific targets requires

Global Land Surface Temperature From the Along-Track Scanning Radiometers

Science.gov (United States)

Ghent, D. J.; Corlett, G. K.; Göttsche, F.-M.; Remedios, J. J.

2017-11-01

The Leicester Along-Track Scanning Radiometer (ATSR) and Sea and Land Surface Temperature Radiometer (SLSTR) Processor for LAnd Surface Temperature (LASPLAST) provides global land surface temperature (LST) products from thermal infrared radiance data. In this paper, the state-of-the-art version of LASPLAST, as deployed in the GlobTemperature project, is described and applied to data from the Advanced Along-Track Scanning Radiometer (AATSR). The LASPLAST retrieval formulation for LST is a nadir-only, two-channel, split-window algorithm, based on biome classification, fractional vegetation, and across-track water vapor dependences. It incorporates globally robust retrieval coefficients derived using highly sampled atmosphere profiles. LASPLAST benefits from appropriate spatial resolution auxiliary information and a new probabilistic-based cloud flagging algorithm. For the first time for a satellite-derived LST product, pixel-level uncertainties characterized in terms of random, locally correlated, and systematic components are provided. The new GlobTemperature GT_ATS_2P Version 1.0 product has been validated for 1 year of AATSR data (2009) against in situ measurements acquired from "gold standard reference" stations: Gobabeb, Namibia, and Evora, Portugal; seven Surface Radiation Budget stations, and the Atmospheric Radiation Measurement station at Southern Great Plains. These data show average absolute biases for the GT_ATS_2P Version 1.0 product of 1.00 K in the daytime and 1.08 K in the nighttime. The improvements in data provenance including better accuracy, fully traceable retrieval coefficients, quantified uncertainty, and more detailed information in the new harmonized format of the GT_ATS_2P product will allow for more significant exploitation of the historical LST data record from the ATSRs and a valuable near-real-time service from the Sea and Land Surface Temperature Radiometers (SLSTRs).

Enhanced

Directory of Open Access Journals (Sweden)

Martin I. Bayala

2014-06-01

Full Text Available Land Surface Temperature (LST is a key parameter in the energy balance model. However, the spatial resolution of the retrieved LST from sensors with high temporal resolution is not accurate enough to be used in local-scale studies. To explore the LST–Normalised Difference Vegetation Index relationship potential and obtain thermal images with high spatial resolution, six enhanced image sharpening techniques were assessed: the disaggregation procedure for radiometric surface temperatures (TsHARP, the Dry Edge Quadratic Function, the Difference of Edges (Ts∗DL and three models supported by the relationship of surface temperature and water stress of vegetation (Normalised Difference Water Index, Normalised Difference Infrared Index and Soil wetness index. Energy Balance Station data and in situ measurements were used to validate the enhanced LST images over a mixed agricultural landscape in the sub-humid Pampean Region of Argentina (PRA, during 2006–2010. Landsat Thematic Mapper (TM and Moderate Resolution Imaging Spectroradiometer (EOS-MODIS thermal datasets were assessed for different spatial resolutions (e.g., 960, 720 and 240 m and the performances were compared with global and local TsHARP procedures. Results suggest that the Ts∗DL technique is the most adequate for simulating LST to high spatial resolution over the heterogeneous landscape of a sub-humid region, showing an average root mean square error of less than 1 K.

Estimation of Diurnal Cycle of Land Surface Temperature at High Temporal and Spatial Resolution from Clear-Sky MODIS Data

Directory of Open Access Journals (Sweden)

Si-Bo Duan

2014-04-01

Full Text Available The diurnal cycle of land surface temperature (LST is an important element of the climate system. Geostationary satellites can provide the diurnal cycle of LST with low spatial resolution and incomplete global coverage, which limits its applications in some studies. In this study, we propose a method to estimate the diurnal cycle of LST at high temporal and spatial resolution from clear-sky MODIS data. This method was evaluated using the MSG-SEVIRI-derived LSTs. The results indicate that this method fits the diurnal cycle of LST well, with root mean square error (RMSE values less than 1 K for most pixels. Because MODIS provides at most four observations per day at a given location, this method was further evaluated using only four MSG-SEVIRI-derived LSTs corresponding to the MODIS overpass times (10:30, 13:30, 22:30, and 01:30 local solar time. The results show that the RMSE values using only four MSG-SEVIRI-derived LSTs are approximately two times larger than those using all LSTs. The spatial distribution of the modeled LSTs at the MODIS pixel scale is presented from 07:00 to 05:00 local solar time of the next day with an increment of 2 hours. The diurnal cycle of the modeled LSTs describes the temporal evolution of the LSTs at the MODIS pixel scale.

Mutations in the Arabidopsis Lst8 and Raptor genes encoding partners of the TOR complex, or inhibition of TOR activity decrease abscisic acid (ABA) synthesis.

Science.gov (United States)

Kravchenko, Alena; Citerne, Sylvie; Jéhanno, Isabelle; Bersimbaev, Rakhmetkazhi I; Veit, Bruce; Meyer, Christian; Leprince, Anne-Sophie

2015-11-27

The Target of Rapamycin (TOR) kinase regulates essential processes in plant growth and development by modulation of metabolism and translation in response to environmental signals. In this study, we show that abscisic acid (ABA) metabolism is also regulated by the TOR kinase. Indeed ABA hormone level strongly decreases in Lst8-1 and Raptor3g mutant lines as well as in wild-type (WT) Arabidopsis plants treated with AZD-8055, a TOR inhibitor. However the growth and germination of these lines are more sensitive to exogenous ABA. The diminished ABA hormone accumulation is correlated with lower transcript levels of ZEP, NCED3 and AAO3 biosynthetic enzymes, and higher transcript amount of the CYP707A2 gene encoding a key-enzyme in abscisic acid catabolism. These results suggest that the TOR signaling pathway is implicated in the regulation of ABA accumulation in Arabidopsis. Copyright © 2015 Elsevier Inc. All rights reserved.

Reproducibility of summertime diurnal precipitation over northern Eurasia simulated by CMIP5 climate models

Science.gov (United States)

Hirota, N.; Takayabu, Y. N.

2015-12-01

Reproducibility of diurnal precipitation over northern Eurasia simulated by CMIP5 climate models in their historical runs were evaluated, in comparison with station data (NCDC-9813) and satellite data (GSMaP-V5). We first calculated diurnal cycles by averaging precipitation at each local solar time (LST) in June-July-August during 1981-2000 over the continent of northern Eurasia (0-180E, 45-90N). Then we examined occurrence time of maximum precipitation and a contribution of diurnally varying precipitation to the total precipitation.The contribution of diurnal precipitation was about 21% in both NCDC-9813 and GSMaP-V5. The maximum precipitation occurred at 18LST in NCDC-9813 but 16LST in GSMaP-V5, indicating some uncertainties even in the observational datasets. The diurnal contribution of the CMIP5 models varied largely from 11% to 62%, and their timing of the precipitation maximum ranged from 11LST to 20LST. Interestingly, the contribution and the timing had strong negative correlation of -0.65. The models with larger diurnal precipitation showed precipitation maximum earlier around noon. Next, we compared sensitivity of precipitation to surface temperature and tropospheric humidity between 5 models with large diurnal precipitation (LDMs) and 5 models with small diurnal precipitation (SDMs). Precipitation in LDMs showed high sensitivity to surface temperature, indicating its close relationship with local instability. On the other hand, synoptic disturbances were more active in SDMs with a dominant role of the large scale condensation, and precipitation in SDMs was more related with tropospheric moisture. Therefore, the relative importance of the local instability and the synoptic disturbances was suggested to be an important factor in determining the contribution and timing of the diurnal precipitation. Acknowledgment: This study is supported by Green Network of Excellence (GRENE) Program by the Ministry of Education, Culture, Sports, Science and Technology

A physics-based algorithm for retrieving land-surface emissivity and temperature from EOS/MODIS data

International Nuclear Information System (INIS)

Wan, Z.; Li, Z.L.

1997-01-01

The authors have developed a physics-based land-surface temperature (LST) algorithm for simultaneously retrieving surface band-averaged emissivities and temperatures from day/night pairs of MODIS (Moderate Resolution Imaging Spectroradiometer) data in seven thermal infrared bands. The set of 14 nonlinear equations in the algorithm is solved with the statistical regression method and the least-squares fit method. This new LST algorithm was tested with simulated MODIS data for 80 sets of band-averaged emissivities calculated from published spectral data of terrestrial materials in wide ranges of atmospheric and surface temperature conditions. Comprehensive sensitivity and error analysis has been made to evaluate the performance of the new LST algorithm and its dependence on variations in surface emissivity and temperature, upon atmospheric conditions, as well as the noise-equivalent temperature difference (NEΔT) and calibration accuracy specifications of the MODIS instrument. In cases with a systematic calibration error of 0.5%, the standard deviations of errors in retrieved surface daytime and nighttime temperatures fall between 0.4--0.5 K over a wide range of surface temperatures for mid-latitude summer conditions. The standard deviations of errors in retrieved emissivities in bands 31 and 32 (in the 10--12.5 microm IR spectral window region) are 0.009, and the maximum error in retrieved LST values falls between 2--3 K

A comprehensive data set of lake surface water temperature over the Tibetan Plateau derived from MODIS LST products 2001-2015.

Science.gov (United States)

Wan, Wei; Li, Huan; Xie, Hongjie; Hong, Yang; Long, Di; Zhao, Limin; Han, Zhongying; Cui, Yaokui; Liu, Baojian; Wang, Cunguang; Yang, Wenting

2017-07-25

Lake surface water temperature (LSWT) is sensitive to long-term changes in thermal structure of lakes and regional air temperature. In the context of global climate change, recent studies showed a significant warming trend of LSWT based on investigating 291 lakes (71% are large lakes, ≥50 km 2 each) globally. However, further efforts are needed to examine variation in LSWT at finer regional spatial and temporal scales. The Tibetan Plateau (TP), known as 'the Roof of the World' and 'Asia's water towers', exerts large influences on and is sensitive to regional and even global climates. Aiming to examine detailed changing patterns and potential driven mechanisms for temperature variations of lakes across the TP region, this paper presents the first comprehensive data set of 15-year (2001-2015) nighttime and daytime LSWT for 374 lakes (≥10 km 2 each), using MODIS (Moderate Resolution Imaging Spectroradiometer) Land Surface Temperature (LST) products as well as four lake boundary shapefiles (i.e., 2002, 2005, 2009, and 2014) derived from Landsat/CBERS/GaoFen-1 satellite images. The data set itself reveals significant information on LSWT and its changes over the TP and is an indispensable variable for numerous applications related to climate change, water budget analysis (particularly lake evaporation), water storage changes, glacier melting and permafrost degradation, etc.

Pressure Drop Versus Flow Rate Analysis of the Limited Streamer Tube Gas System of the BaBar Muon Detector Upgrade

International Nuclear Information System (INIS)

Yi, M.

2004-01-01

It has been proposed that Limited Streamer Tubes (LST) be used in the current upgrade of the muon detector in the BaBar detector. An LST consists of a thin silver plated wire centered in a graphite-coated cell. One standard LST tube consists of eight such cells, and two or three such tubes form an LST module. Under operation, the cells are filled with a gas mixture of CO 2 , argon and isobutane. During normal operation of the detector, the gas will be flushed out of the system at a constant low rate of one volume change per day. During times such as installation, however, it is often desired to flush and change the LST gas volumes very rapidly, leading to higher than normal pressure which may damage the modules. This project studied this pressure as a function of flow rate and the number of modules that are put in series in search of the maximal safe flow rate at which to flush the modules. Measurements of pressure drop versus flow rate were taken using a flow meter and a pressure transducer on configurations of one to five modules put in series. Minimal Poly-Flo tubing was used for all connections between test equipment and modules. They contributed less than 25% to all measurements. A ratio of 0.00022 ± 0.00001 mmHg per Standard Cubic Centimeter per Minute (SCCM) per module was found, which was a slight overestimate since it included the contributions from the tubing connections. However, for the purpose of finding a flow rate at which the modules can be safely flushed, this overestimate acts as a safety cushion. For a standard module with a volume of 16 liters and a known safe overpressure of 2 inches of water, the ratio translates into a flow rate of 17000 ± 1000SCCM and a time requirement of 56 ± 5 seconds to flush an entire module

Geothermal Anomaly Mapping Using Landsat ETM+ Data in Ilan Plain, Northeastern Taiwan

Science.gov (United States)

Chan, Hai-Po; Chang, Chung-Pai; Dao, Phuong D.

2018-01-01

Geothermal energy is an increasingly important component of green energy in the globe. A prerequisite for geothermal energy development is to acquire the local and regional geothermal prospects. Existing geophysical methods of estimating the geothermal potential are usually limited to the scope of prospecting because of the operation cost and site reachability in the field. Thus, explorations in a large-scale area such as the surface temperature and the thermal anomaly primarily rely on satellite thermal infrared imagery. This study aims to apply and integrate thermal infrared (TIR) remote sensing technology with existing geophysical methods for the geothermal exploration in Taiwan. Landsat 7 (L7) Enhanced Thematic Mapper Plus (ETM+) imagery is used to retrieve the land surface temperature (LST) in Ilan plain. Accuracy assessment of satellite-derived LST is conducted by comparing with the air temperature data from 11 permanent meteorological stations. The correlation coefficient of linear regression between air temperature and LST retrieval is 0.76. The MODIS LST product is used for the cross validation of Landsat derived LSTs. Furthermore, Landsat ETM+ multi-temporal brightness temperature imagery for the verification of the LST anomaly results were performed. LST Results indicate that thermal anomaly areas appear correlating with the development of faulted structure. Selected geothermal anomaly areas are validated in detail by field investigation of hot springs and geothermal drillings. It implies that occurrences of hot springs and geothermal drillings are in good spatial agreement with anomaly areas. In addition, the significant low-resistivity zones observed in the resistivity sections are echoed with the LST profiles when compared with in the Chingshui geothermal field. Despite limited to detecting the surficial and the shallow buried geothermal resources, this work suggests that TIR remote sensing is a valuable tool by providing an effective way of mapping

Thermal anomalies detection before strong earthquakes (M > 6.0 using interquartile, wavelet and Kalman filter methods

Directory of Open Access Journals (Sweden)

M. Akhoondzadeh

2011-04-01

Full Text Available Thermal anomaly is known as a significant precursor of strong earthquakes, therefore Land Surface Temperature (LST time series have been analyzed in this study to locate relevant anomalous variations prior to the Bam (26 December 2003, Zarand (22 February 2005 and Borujerd (31 March 2006 earthquakes. The duration of the three datasets which are comprised of MODIS LST images is 44, 28 and 46 days for the Bam, Zarand and Borujerd earthquakes, respectively. In order to exclude variations of LST from temperature seasonal effects, Air Temperature (AT data derived from the meteorological stations close to the earthquakes epicenters have been taken into account. The detection of thermal anomalies has been assessed using interquartile, wavelet transform and Kalman filter methods, each presenting its own independent property in anomaly detection. The interquartile method has been used to construct the higher and lower bounds in LST data to detect disturbed states outside the bounds which might be associated with impending earthquakes. The wavelet transform method has been used to locate local maxima within each time series of LST data for identifying earthquake anomalies by a predefined threshold. Also, the prediction property of the Kalman filter has been used in the detection process of prominent LST anomalies. The results concerning the methodology indicate that the interquartile method is capable of detecting the highest intensity anomaly values, the wavelet transform is sensitive to sudden changes, and the Kalman filter method significantly detects the highest unpredictable variations of LST. The three methods detected anomalous occurrences during 1 to 20 days prior to the earthquakes showing close agreement in results found between the different applied methods on LST data in the detection of pre-seismic anomalies. The proposed method for anomaly detection was also applied on regions irrelevant to earthquakes for which no anomaly was detected

Afforestation in China cools local land surface temperature

OpenAIRE

Peng, Shu-Shi; Piao, Shilong; Zeng, Zhenzhong; Ciais, Philippe; Zhou, Liming; Li, Laurent Z. X.; Myneni, Ranga B.; Yin, Yi; Zeng, Hui

2014-01-01

International audience; China has the largest afforested area in the world (~62 million hectares in 2008), and these forests are carbon sinks. The climatic effect of these new forests depends on how radiant and turbulent energy fluxes over these plantations modify surface temperature. For instance, a lower albedo may cause warming, which negates the climatic benefits of carbon sequestration. Here, we used satellite measurements of land surface temperature (LST) from planted forests and adjace...

Estimating surface turbulent heat fluxes from land surface temperature and soil moisture using the particle batch smoother

Science.gov (United States)

Lu, Yang; Dong, Jianzhi; Steele-Dunne, Susan; van de Giesen, Nick

2016-04-01

This study is focused on estimating surface sensible and latent heat fluxes from land surface temperature (LST) time series and soil moisture observations. Surface turbulent heat fluxes interact with the overlying atmosphere and play a crucial role in meteorology, hydrology and other climate-related fields, but in-situ measurements are costly and difficult. It has been demonstrated that the time series of LST contains information of energy partitioning and that surface turbulent heat fluxes can be determined from assimilation of LST. These studies are mainly based on two assumptions: (1) a monthly value of bulk heat transfer coefficient under neutral conditions (CHN) which scales the sum of the fluxes, and (2) an evaporation fraction (EF) which stays constant during the near-peak hours of the day. Previous studies have applied variational and ensemble approaches to this problem. Here the newly developed particle batch smoother (PBS) algorithm is adopted to test its capability in this application. The PBS can be seen as an extension of the standard particle filter (PF) in which the states and parameters within a fix window are updated in a batch using all observations in the window. The aim of this study is two-fold. First, the PBS is used to assimilate only LST time series into the force-restore model to estimate fluxes. Second, a simple soil water transfer scheme is introduced to evaluate the benefit of assimilating soil moisture observations simultaneously. The experiments are implemented using the First ISLSCP (International Satellite Land Surface Climatology Project) (FIFE) data. It is shown that the restored LST time series using PBS agrees very well with observations, and that assimilating LST significantly improved the flux estimation at both daily and half-hourly time scales. When soil moisture is introduced to further constrain EF, the accuracy of estimated EF is greatly improved. Furthermore, the RMSEs of retrieved fluxes are effectively reduced at both

Quasinormal modes of brane-localized standard model fields. II. Kerr black holes

International Nuclear Information System (INIS)

Kanti, P.; Konoplya, R. A.; Zhidenko, A.

2006-01-01

This paper presents a comprehensive study of the fundamental quasinormal modes of all standard model fields propagating on a brane embedded in a higher-dimensional rotating black-hole spacetime. The equations of motion for fields with spin s=0, 1/2 and 1 propagating in the induced-on-the-brane background are solved numerically, and the dependence of their QN spectra on the black-hole angular momentum and dimensionality of spacetime is investigated. It is found that the brane-localized field perturbations are longer-lived when the higher-dimensional black hole rotates faster, while an increase in the number of transverse-to-the-brane dimensions reduces their lifetime. Finally, the quality factor Q, that determines the best oscillator among the different field perturbations, is investigated and found to depend on properties of both the particular field studied (spin, multipole numbers) and the gravitational background (dimensionality, black-hole angular momentum parameter)

Carbon finance and pro-poor co-benefits: The Gold Standard and Climate, Community and Biodiversity Standards

Energy Technology Data Exchange (ETDEWEB)

Wood, Rachel

2011-04-15

This paper assesses the practical contribution of the Gold Standard (GS) and Climate Community and Biodiversity (CCB) Standards to local development through the identification of high quality carbon offset projects and ensuring high standards of consultation with local communities during project development and implementation. It is based on desk research, involving analysis of the GS and CCB Standards' project databases, project design documents, and secondary literature. In addition, over 20 representatives of the two standards systems, project developers, NGO representatives, and researchers were interviewed. The paper concludes that both standard systems successfully reward high quality projects which have a demonstrated commitment to local consultations and sustainable development benefits. Moreover, they serve to give well-meaning project developers frameworks with which to ensure that a wide range of criteria are considered in planning and implementing projects. As voluntary standards, it is unrealistic to expect either the GS or CCB Standards to improve poor-quality or unsustainable projects.

Carbon finance and pro-poor co-benefits: The Gold Standard and Climate, Community and Biodiversity Standards

Energy Technology Data Exchange (ETDEWEB)

Wood, Rachel

2011-04-15

This paper assesses the practical contribution of the Gold Standard (GS) and Climate Community and Biodiversity (CCB) Standards to local development through the identification of high quality carbon offset projects and ensuring high standards of consultation with local communities during project development and implementation. It is based on desk research, involving analysis of the GS and CCB Standards' project databases, project design documents, and secondary literature. In addition, over 20 representatives of the two standards systems, project developers, NGO representatives, and researchers were interviewed. The paper concludes that both standard systems successfully reward high quality projects which have a demonstrated commitment to local consultations and sustainable development benefits. Moreover, they serve to give well-meaning project developers frameworks with which to ensure that a wide range of criteria are considered in planning and implementing projects. As voluntary standards, it is unrealistic to expect either the GS or CCB Standards to improve poor-quality or unsustainable projects.

An Improved Mono-Window Algorithm for Land Surface Temperature Retrieval from Landsat 8 Thermal Infrared Sensor Data

Directory of Open Access Journals (Sweden)

Fei Wang

2015-04-01

Full Text Available The successful launch of the Landsat 8 satellite with two thermal infrared bands on February 11, 2013, for continuous Earth observation provided another opportunity for remote sensing of land surface temperature (LST. However, calibration notices issued by the United States Geological Survey (USGS indicated that data from the Landsat 8 Thermal Infrared Sensor (TIRS Band 11 have large uncertainty and suggested using TIRS Band 10 data as a single spectral band for LST estimation. In this study, we presented an improved mono-window (IMW algorithm for LST retrieval from the Landsat 8 TIRS Band 10 data. Three essential parameters (ground emissivity, atmospheric transmittance and effective mean atmospheric temperature were required for the IMW algorithm to retrieve LST. A new method was proposed to estimate the parameter of effective mean atmospheric temperature from local meteorological data. The other two essential parameters could be both estimated through the so-called land cover approach. Sensitivity analysis conducted for the IMW algorithm revealed that the possible error in estimating the required atmospheric water vapor content has the most significant impact on the probable LST estimation error. Under moderate errors in both water vapor content and ground emissivity, the algorithm had an accuracy of ~1.4 K for LST retrieval. Validation of the IMW algorithm using the simulated datasets for various situations indicated that the LST difference between the retrieved and the simulated ones was 0.67 K on average, with an RMSE of 0.43 K. Comparison of our IMW algorithm with the single-channel (SC algorithm for three main atmosphere profiles indicated that the average error and RMSE of the IMW algorithm were −0.05 K and 0.84 K, respectively, which were less than the −2.86 K and 1.05 K of the SC algorithm. Application of the IMW algorithm to Nanjing and its vicinity in east China resulted in a reasonable LST estimation for the region. Spatial

An Algorithm for Retrieving Land Surface Temperatures Using VIIRS Data in Combination with Multi-Sensors

Science.gov (United States)

Xia, Lang; Mao, Kebiao; Ma, Ying; Zhao, Fen; Jiang, Lipeng; Shen, Xinyi; Qin, Zhihao

2014-01-01

A practical algorithm was proposed to retrieve land surface temperature (LST) from Visible Infrared Imager Radiometer Suite (VIIRS) data in mid-latitude regions. The key parameter transmittance is generally computed from water vapor content, while water vapor channel is absent in VIIRS data. In order to overcome this shortcoming, the water vapor content was obtained from Moderate Resolution Imaging Spectroradiometer (MODIS) data in this study. The analyses on the estimation errors of vapor content and emissivity indicate that when the water vapor errors are within the range of ±0.5 g/cm2, the mean retrieval error of the present algorithm is 0.634 K; while the land surface emissivity errors range from −0.005 to +0.005, the mean retrieval error is less than 1.0 K. Validation with the standard atmospheric simulation shows the average LST retrieval error for the twenty-three land types is 0.734 K, with a standard deviation value of 0.575 K. The comparison between the ground station LST data indicates the retrieval mean accuracy is −0.395 K, and the standard deviation value is 1.490 K in the regions with vegetation and water cover. Besides, the retrieval results of the test data have also been compared with the results measured by the National Oceanic and Atmospheric Administration (NOAA) VIIRS LST products, and the results indicate that 82.63% of the difference values are within the range of −1 to 1 K, and 17.37% of the difference values are within the range of ±2 to ±1 K. In a conclusion, with the advantages of multi-sensors taken fully exploited, more accurate results can be achieved in the retrieval of land surface temperature. PMID:25397919

Dynamics and controls of urban heat sink and island phenomena in a desert city: Development of a local climate zone scheme using remotely-sensed inputs

Science.gov (United States)

Nassar, Ahmed K.; Blackburn, G. Alan; Whyatt, J. Duncan

2016-09-01

This study aims to determine the dynamics and controls of Surface Urban Heat Sinks (SUHS) and Surface Urban Heat Islands (SUHI) in desert cities, using Dubai as a case study. A Local Climate Zone (LCZ) schema was developed to subdivide the city into different zones based on similarities in land cover and urban geometry. Proximity to the Gulf Coast was also determined for each LCZ. The LCZs were then used to sample seasonal and daily imagery from the MODIS thermal sensor to determine Land Surface Temperature (LST) variations relative to desert sand. Canonical correlation techniques were then applied to determine which factors explained the variability between urban and desert LST. Our results indicate that the daytime SUHS effect is greatest during the summer months (typically ∼3.0 °C) with the strongest cooling effects in open high-rise zones of the city. In contrast, the night-time SUHI effect is greatest during the winter months (typically ∼3.5 °C) with the strongest warming effects in compact mid-rise zones of the city. Proximity to the Arabian Gulf had the largest influence on both SUHS and SUHI phenomena, promoting daytime cooling in the summer months and night-time warming in the winter months. However, other parameters associated with the urban environment such as building height had an influence on daytime cooling, with larger buildings promoting shade and variations in airflow. Likewise, other parameters such as sky view factor contributed to night-time warming, with higher temperatures associated with limited views of the sky.

Validation of Land Surface Temperature from Sentinel-3

Science.gov (United States)

Ghent, D.

2017-12-01

One of the main objectives of the Sentinel-3 mission is to measure sea- and land-surface temperature with high-end accuracy and reliability in support of environmental and climate monitoring in an operational context. Calibration and validation are thus key criteria for operationalization within the framework of the Sentinel-3 Mission Performance Centre (S3MPC). Land surface temperature (LST) has a long heritage of satellite observations which have facilitated our understanding of land surface and climate change processes, such as desertification, urbanization, deforestation and land/atmosphere coupling. These observations have been acquired from a variety of satellite instruments on platforms in both low-earth orbit and in geostationary orbit. Retrieval accuracy can be a challenge though; surface emissivities can be highly variable owing to the heterogeneity of the land, and atmospheric effects caused by the presence of aerosols and by water vapour absorption can give a bias to the underlying LST. As such, a rigorous validation is critical in order to assess the quality of the data and the associated uncertainties. Validation of the level-2 SL_2_LST product, which became freely available on an operational basis from 5th July 2017 builds on an established validation protocol for satellite-based LST. This set of guidelines provides a standardized framework for structuring LST validation activities. The protocol introduces a four-pronged approach which can be summarised thus: i) in situ validation where ground-based observations are available; ii) radiance-based validation over sites that are homogeneous in emissivity; iii) intercomparison with retrievals from other satellite sensors; iv) time-series analysis to identify artefacts on an interannual time-scale. This multi-dimensional approach is a necessary requirement for assessing the performance of the LST algorithm for the Sea and Land Surface Temperature Radiometer (SLSTR) which is designed around biome

Impacts of land use and land cover on surface and air temperature in urban landscapes

Science.gov (United States)

Crum, S.; Jenerette, D.

2015-12-01

Accelerating urbanization affects regional climate as the result of changing land cover and land use (LCLU). Urban land cover composition may provide valuable insight into relationships among urbanization, air, and land-surface temperature (Ta and LST, respectively). Climate may alter these relationships, where hotter climates experience larger LULC effects. To address these hypotheses we examined links between Ta, LST, LCLU, and vegetation across an urban coastal to desert climate gradient in southern California, USA. Using surface temperature radiometers, continuously measuring LST on standardized asphalt, concrete, and turf grass surfaces across the climate gradient, we found a 7.2°C and 4.6°C temperature decrease from asphalt to vegetated cover in the coast and desert, respectively. There is 131% more temporal variation in asphalt than turf grass surfaces, but 37% less temporal variation in concrete than turf grass. For concrete and turf grass surfaces, temporal variation in temperature increased from coast to desert. Using ground-based thermal imagery, measuring LST for 24 h sequences over citrus orchard and industrial use locations, we found a 14.5°C temperature decrease from industrial to orchard land use types (38.4°C and 23.9°C, respectively). Additionally, industrial land use types have 209% more spatial variation than orchard (CV=0.20 and 0.09, respectively). Using a network of 300 Ta (iButton) sensors mounted in city street trees throughout the region and hyperspectral imagery data we found urban vegetation greenness, measured using the normalized difference vegetation index (NDVI), was negatively correlated to Ta at night across the climate gradient. Contrasting previous findings, the closest coupling between NDVI and Ta is at the coast from 0000 h to 0800 h (highest r2 = 0.6, P urbanized regions of southern California, USA decrease Ta and LST and spatial variation in LST, while built surfaces and land uses have the opposite effect. Furthermore

Globalization quickly increased need for moving from local to international standards

Energy Technology Data Exchange (ETDEWEB)

Cappelli, Cataldo

2005-07-01

'Standardization' quickly changed in the past few years, due to the market's globalization that needs international standards as important instruments in eliminating technical barriers to trade. The 'Petroleum Sector' chose moving to international standards jointly processed by the International Organization for Standardization (ISO) and the American Petroleum Institute (API) that played the role of historical reference. Taking into account that oil industry wants only one Standard worldwide used, also Europe decided for adopting these ISO Standards as European Standards. The result is much better considering that also Russia and China seem to adopt these ISO documents as their national standards. It is so becoming much more significant the 'motto' that ISO TC 67 'Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries' adopted for its standardization activities: 'Do it once, do it right, do it internationally'. Examples of such international Standards worldwide used as National Standards are: ISO 11960:2004 - 'Steel pipes for use as casing or tubing for wells' and; ISO/DIS 3183 - 'Steel pipe for pipeline transportation systems' (under preparation). Standardization has so grown from technical to management tool and countries are also moving, including standards in more areas of its legislations. (author)

The Elusive Standard of Care.

Science.gov (United States)

Cooke, Brian K; Worsham, Elizabeth; Reisfield, Gary M

2017-09-01

In medical negligence cases, the forensic expert must explain to a trier of fact what a defendant physician should have done, or not done, in a specific set of circumstances and whether the physician's conduct constitutes a breach of duty. The parameters of the duty are delineated by the standard of care. Many facets of the standard of care have been well explored in the literature, but gaps remain in a complete understanding of this concept. We examine the standard of care, its origins, and who determines the prevailing standard, beginning with an overview of the historical roots of the standard of care and, using case law, tracing its evolution from the 19th century through the early 21st century. We then analyze the locality rule and consider local, state, and national standards of care. The locality rule requires a defendant physician to provide the same degree of skill and care that is required of a physician practicing in the same or similar community. This rule remains alive in some jurisdictions in the United States. Last, we address the relationship between the standard of care and clinical practice guidelines. © 2017 American Academy of Psychiatry and the Law.

Globalization quickly increased need for moving from local to international standards

Energy Technology Data Exchange (ETDEWEB)

Cappelli, Cataldo

2005-07-01

'Standardization' quickly changed in the past few years, due to the market's globalization that needs international standards as important instruments in eliminating technical barriers to trade. The 'Petroleum Sector' chose moving to international standards jointly processed by the International Organization for Standardization (ISO) and the American Petroleum Institute (API) that played the role of historical reference. Taking into account that oil industry wants only one Standard worldwide used, also Europe decided for adopting these ISO Standards as European Standards. The result is much better considering that also Russia and China seem to adopt these ISO documents as their national standards. It is so becoming much more significant the 'motto' that ISO TC 67 'Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries' adopted for its standardization activities: 'Do it once, do it right, do it internationally'. Examples of such international Standards worldwide used as National Standards are: ISO 11960:2004 - 'Steel pipes for use as casing or tubing for wells' and; ISO/DIS 3183 - 'Steel pipe for pipeline transportation systems' (under preparation). Standardization has so grown from technical to management tool and countries are also moving, including standards in more areas of its legislations. (author)

Prediction equation for lower limbs lean soft tissue in circumpubertal boys using anthropometry and biological maturation.

Directory of Open Access Journals (Sweden)

João Valente-dos-Santos

Full Text Available Lean soft tissue (LST, a surrogate of skeletal muscle mass, is largely limited to appendicular body regions. Simple and accurate methods to estimate lower limbs LST are often used in attempts to partition out the influence of body size on performance outputs. The aim of the current study was to develop and cross-validate a new model to predict lower limbs LST in boys aged 10-13 years, using dual-energy X-ray absorptiometry (DXA as the reference method. Total body and segmental (lower limbs composition were assessed with a Hologic Explorer-W QDR DXA scanner in a cross-sectional sample of 75 Portuguese boys (144.8±6.4 cm; 40.2±9.0 kg. Skinfolds were measured at the anterior and posterior mid-thigh, and medial calf. Circumferences were measured at the proximal, mid and distal thigh. Leg length was estimated as stature minus sitting height. Current stature expressed as a percentage of attained predicted mature stature (PMS was used as an estimate of biological maturity status. Backward proportional allometric models were used to identify the model with the best statistical fit: ln (lower limbs LST  = 0.838× ln (body mass +0.476× ln (leg length - 0.135× ln (mid-thigh circumference - 0.053× ln (anterior mid-thigh skinfold - 0.098× ln (medial calf skinfold - 2.680+0.010× (percentage of attained PMS (R = 0.95. The obtained equation was cross-validated using the predicted residuals sum of squares statistics (PRESS method (R2PRESS = 0.90. Deming repression analysis between predicted and current lower limbs LST showed a standard error of estimation of 0.52 kg (95% limits of agreement: 0.77 to -1.27 kg. The new model accurately predicts lower limbs LST in circumpubertal boys.

Effects of Land Use/Cover Changes and Urban Forest Configuration on Urban Heat Islands in a Loess Hilly Region: Case Study Based on Yan’an City, China

Science.gov (United States)

Zhang, Xinping; Hao, Hongke; Zhang, Fangfang; Hu, Youning

2017-01-01

In this study Yan’an City, a typical hilly valley city, was considered as the study area in order to explain the relationships between the surface urban heat island (SUHI) and land use/land cover (LULC) types, the landscape pattern metrics of LULC types and land surface temperature (LST) and remote sensing indexes were retrieved from Landsat data during 1990–2015, and to find factors contributed to the green space cool island intensity (GSCI) through field measurements of 34 green spaces. The results showed that during 1990–2015, because of local anthropogenic activities, SUHI was mainly located in lower vegetation cover areas. There was a significant suburban-urban gradient in the average LST, as well as its heterogeneity and fluctuations. Six landscape metrics comprising the fractal dimension index, percentage of landscape, aggregation index, division index, Shannon’s diversity index, and expansion intensity of the classified LST spatiotemporal changes were paralleled to LULC changes, especially for construction land, during the past 25 years. In the urban area, an index-based built-up index was the key positive factor for explaining LST increases, whereas the normalized difference vegetation index and modified normalized difference water index were crucial factors for explaining LST decreases during the study periods. In terms of the heat mitigation performance of green spaces, mixed forest was better than pure forest, and the urban forest configuration had positive effects on GSCI. The results of this study provide insights into the importance of species choice and the spatial design of green spaces for cooling the environment. PMID:28933770

Effects of Land Use/Cover Changes and Urban Forest Configuration on Urban Heat Islands in a Loess Hilly Region: Case Study Based on Yan’an City, China

Directory of Open Access Journals (Sweden)

Xinping Zhang

2017-07-01

Full Text Available In this study Yan’an City, a typical hilly valley city, was considered as the study area in order to explain the relationships between the surface urban heat island (SUHI and land use/land cover (LULC types, the landscape pattern metrics of LULC types and land surface temperature (LST and remote sensing indexes were retrieved from Landsat data during 1990–2015, and to find factors contributed to the green space cool island intensity (GSCI through field measurements of 34 green spaces. The results showed that during 1990–2015, because of local anthropogenic activities, SUHI was mainly located in lower vegetation cover areas. There was a significant suburban-urban gradient in the average LST, as well as its heterogeneity and fluctuations. Six landscape metrics comprising the fractal dimension index, percentage of landscape, aggregation index, division index, Shannon’s diversity index, and expansion intensity of the classified LST spatiotemporal changes were paralleled to LULC changes, especially for construction land, during the past 25 years. In the urban area, an index-based built-up index was the key positive factor for explaining LST increases, whereas the normalized difference vegetation index and modified normalized difference water index were crucial factors for explaining LST decreases during the study periods. In terms of the heat mitigation performance of green spaces, mixed forest was better than pure forest, and the urban forest configuration had positive effects on GSCI. The results of this study provide insights into the importance of species choice and the spatial design of green spaces for cooling the environment.

Effects of Land Use/Cover Changes and Urban Forest Configuration on Urban Heat Islands in a Loess Hilly Region: Case Study Based on Yan'an City, China.

Science.gov (United States)

Zhang, Xinping; Wang, Dexiang; Hao, Hongke; Zhang, Fangfang; Hu, Youning

2017-07-26

In this study Yan'an City, a typical hilly valley city, was considered as the study area in order to explain the relationships between the surface urban heat island (SUHI) and land use/land cover (LULC) types, the landscape pattern metrics of LULC types and land surface temperature (LST) and remote sensing indexes were retrieved from Landsat data during 1990-2015, and to find factors contributed to the green space cool island intensity (GSCI) through field measurements of 34 green spaces. The results showed that during 1990-2015, because of local anthropogenic activities, SUHI was mainly located in lower vegetation cover areas. There was a significant suburban-urban gradient in the average LST, as well as its heterogeneity and fluctuations. Six landscape metrics comprising the fractal dimension index, percentage of landscape, aggregation index, division index, Shannon's diversity index, and expansion intensity of the classified LST spatiotemporal changes were paralleled to LULC changes, especially for construction land, during the past 25 years. In the urban area, an index-based built-up index was the key positive factor for explaining LST increases, whereas the normalized difference vegetation index and modified normalized difference water index were crucial factors for explaining LST decreases during the study periods. In terms of the heat mitigation performance of green spaces, mixed forest was better than pure forest, and the urban forest configuration had positive effects on GSCI. The results of this study provide insights into the importance of species choice and the spatial design of green spaces for cooling the environment.

Text localization using standard deviation analysis of structure elements and support vector machines

Directory of Open Access Journals (Sweden)

Zagoris Konstantinos

2011-01-01

Full Text Available Abstract A text localization technique is required to successfully exploit document images such as technical articles and letters. The proposed method detects and extracts text areas from document images. Initially a connected components analysis technique detects blocks of foreground objects. Then, a descriptor that consists of a set of suitable document structure elements is extracted from the blocks. This is achieved by incorporating an algorithm called Standard Deviation Analysis of Structure Elements (SDASE which maximizes the separability between the blocks. Another feature of the SDASE is that its length adapts according to the requirements of the application. Finally, the descriptor of each block is used as input to a trained support vector machines that classify the block as text or not. The proposed technique is also capable of adjusting to the text structure of the documents. Experimental results on benchmarking databases demonstrate the effectiveness of the proposed method.

Later Outcomes and Alpha/Beta Estimate From Hypofractionated Conformal Three-Dimensional Radiotherapy Versus Standard Fractionation for Localized Prostate Cancer

Energy Technology Data Exchange (ETDEWEB)

Leborgne, Felix [Department of Radiation Oncology, Hospital Italiano, Montevideo (Uruguay); Fowler, Jack, E-mail: jackfowlersbox@gmail.com [Department of Human Oncology, University of Wisconsin Medical School, Madison, WI (United States); Leborgne, Jose H.; Mezzera, Julieta [Department of Radiation Oncology, Hospital Italiano, Montevideo (Uruguay)

2012-03-01

Purpose: Now that the follow-up time has exceeded 5 years, an estimate of the {alpha}/{beta} ratio can be presented. The additional late outcomes in patients treated with three-dimensional conformal external beam radiotherapy for localized prostate cancer using a hypofractionated vs. a standard fractionation regimen are reported from this prospective nonrandomized contemporary comparison. Methods and Materials: A total of 114 nonrandomized patients chose hypofractionation delivered in 20 fractions of 3 Gy or 3.15 Gy (mean 3.06 Gy) for localized prostate cancer within a median overall time of 32 days (range, 29-49) using four fractions weekly. A total of 160 comparable patients were contemporarily treated within a median of 55 days (range 49-66). The median follow-up was 66 months (range, 24-95) for the hypofractionated arm and 63 months (range, 36-92) for the standard arm. The percentage of patients in the low-, medium-, and high-risk groups was 36%, 46%, and 18% in the hypofractionated arm and 44%, 50%, and 6% in standard arm (2 Gy), respectively. Results: The 5-year actuarial biochemical absence of disease (prostate-specific antigen nadir + 2 ng/mL) and disease-free survival rate was the same at 89% in both arms, making the {alpha}/{beta} calculation unambiguous. The point ratio of {alpha}/{beta} was 1.86 (95% confidence interval, 0.7-5.1 Gy). The 95% confidence interval was determined entirely by the binomial confidence limits in the numbers of patients. Rectal reactions of grade 3 and 4 occurred in 1 of 114 (hypofractionated) and 2 of 160 (standard) patients. Conclusions: The presented three-dimensional conformal regimen was acceptable, and the {alpha}/{beta} value was 1.8, in agreement with other very recent low meta-analyses (reviewed in the '' section).

Communications standards

CERN Document Server

Stokes, A V

1986-01-01

Communications Standards deals with the standardization of computer communication networks. This book examines the types of local area networks (LANs) that have been developed and looks at some of the relevant protocols in more detail. The work of Project 802 is briefly discussed, along with a protocol which has developed from one of the LAN standards and is now a de facto standard in one particular area, namely the Manufacturing Automation Protocol (MAP). Factors that affect the usage of networks, such as network management and security, are also considered. This book is divided into three se

Construction and Analysis of Long-Term Surface Temperature Dataset in Fujian Province

Science.gov (United States)

Li, W. E.; Wang, X. Q.; Su, H.

2017-09-01

Land surface temperature (LST) is a key parameter of land surface physical processes on global and regional scales, linking the heat fluxes and interactions between the ground and atmosphere. Based on MODIS 8-day LST products (MOD11A2) from the split-window algorithms, we constructed and obtained the monthly and annual LST dataset of Fujian Province from 2000 to 2015. Then, we analyzed the monthly and yearly time series LST data and further investigated the LST distribution and its evolution features. The average LST of Fujian Province reached the highest in July, while the lowest in January. The monthly and annual LST time series present a significantly periodic features (annual and interannual) from 2000 to 2015. The spatial distribution showed that the LST in North and West was lower than South and East in Fujian Province. With the rapid development and urbanization of the coastal area in Fujian Province, the LST in coastal urban region was significantly higher than that in mountainous rural region. The LST distributions might affected by the climate, topography and land cover types. The spatio-temporal distribution characteristics of LST could provide good references for the agricultural layout and environment monitoring in Fujian Province.

CONSTRUCTION AND ANALYSIS OF LONG-TERM SURFACE TEMPERATURE DATASET IN FUJIAN PROVINCE

Directory of Open Access Journals (Sweden)

W. E. Li

2017-09-01

Full Text Available Land surface temperature (LST is a key parameter of land surface physical processes on global and regional scales, linking the heat fluxes and interactions between the ground and atmosphere. Based on MODIS 8-day LST products (MOD11A2 from the split-window algorithms, we constructed and obtained the monthly and annual LST dataset of Fujian Province from 2000 to 2015. Then, we analyzed the monthly and yearly time series LST data and further investigated the LST distribution and its evolution features. The average LST of Fujian Province reached the highest in July, while the lowest in January. The monthly and annual LST time series present a significantly periodic features (annual and interannual from 2000 to 2015. The spatial distribution showed that the LST in North and West was lower than South and East in Fujian Province. With the rapid development and urbanization of the coastal area in Fujian Province, the LST in coastal urban region was significantly higher than that in mountainous rural region. The LST distributions might affected by the climate, topography and land cover types. The spatio-temporal distribution characteristics of LST could provide good references for the agricultural layout and environment monitoring in Fujian Province.

SPATIAL AND TEMPORAL VARIATION OF LAND SURFACE TEMPERATURE IN FUJIAN PROVINCE FROM 2001 TO 2015

Directory of Open Access Journals (Sweden)

Y. Li

2018-04-01

Full Text Available Land surface temperature (LST is an essential parameter in the physics of land surface processes. The spatiotemporal variations of LST on the Fujian province were studied using AQUA Moderate Resolution Imaging Spectroradiometer LST data. Considering the data gaps in remotely sensed LST products caused by cloud contamination, the Savitzky-Golay (S-G filter method was used to eliminate the influence of cloud cover and to describe the periodical signals of LST. Observed air temperature data from 27 weather stations were employed to evaluate the fitting performance of the S-G filter method. Results indicate that S-G can effectively fit the LST time series and remove the influence of cloud cover. Based on the S-G-derived result, Spatial and temporal Variations of LST in Fujian province from 2001 to 2015 are analysed through slope analysis. The results show that: 1 the spatial distribution of annual mean LST generally exhibits consistency with altitude in the study area and the average of LST was much higher in the east than in the west. 2 The annual mean temperature of LST declines slightly among 15 years in Fujian. 3 Slope analysis reflects the spatial distribution characteristics of LST changing trend in Fujian.Improvement areas of LST are mainly concentrated in the urban areas of Fujian, especially in the eastern urban areas. Apparent descent areas are mainly distributed in the area of Zhangzhou and eastern mountain area.

Spatial and Temporal Variation of Land Surface Temperature in Fujian Province from 2001 TO 2015

Science.gov (United States)

Li, Y.; Wang, X.; Ding, Z.

2018-04-01

Land surface temperature (LST) is an essential parameter in the physics of land surface processes. The spatiotemporal variations of LST on the Fujian province were studied using AQUA Moderate Resolution Imaging Spectroradiometer LST data. Considering the data gaps in remotely sensed LST products caused by cloud contamination, the Savitzky-Golay (S-G) filter method was used to eliminate the influence of cloud cover and to describe the periodical signals of LST. Observed air temperature data from 27 weather stations were employed to evaluate the fitting performance of the S-G filter method. Results indicate that S-G can effectively fit the LST time series and remove the influence of cloud cover. Based on the S-G-derived result, Spatial and temporal Variations of LST in Fujian province from 2001 to 2015 are analysed through slope analysis. The results show that: 1) the spatial distribution of annual mean LST generally exhibits consistency with altitude in the study area and the average of LST was much higher in the east than in the west. 2) The annual mean temperature of LST declines slightly among 15 years in Fujian. 3) Slope analysis reflects the spatial distribution characteristics of LST changing trend in Fujian.Improvement areas of LST are mainly concentrated in the urban areas of Fujian, especially in the eastern urban areas. Apparent descent areas are mainly distributed in the area of Zhangzhou and eastern mountain area.

Financial Accounting: Classifications and Standard Terminology for Local and State School Systems. State Educational Records and Reports Series: Handbook II, Revised.

Science.gov (United States)

Roberts, Charles T., Comp.; Lichtenberger, Allan R., Comp.

This handbook has been prepared as a vehicle or mechanism for program cost accounting and as a guide to standard school accounting terminology for use in all types of local and intermediate education agencies. In addition to classification descriptions, program accounting definitions, and proration of cost procedures, some units of measure and…

Quality Assessment of S-NPP VIIRS Land Surface Temperature Product

Directory of Open Access Journals (Sweden)

Yuling Liu

2015-09-01

Full Text Available The VIIRS Land Surface Temperature (LST Environmental Data Record (EDR has reached validated (V1 stage maturity in December 2014. This study compares VIIRS v1 LST with the ground in situ observations and with heritage LST product from MODIS Aqua and AATSR. Comparisons against U.S. SURFRAD ground observations indicate a similar accuracy among VIIRS, MODIS and AATSR LST, in which VIIRS LST presents an overall accuracy of −0.41 K and precision of 2.35 K. The result over arid regions in Africa suggests that VIIRS and MODIS underestimate the LST about 1.57 K and 2.97 K, respectively. The cross comparison indicates an overall close LST estimation between VIIRS and MODIS. In addition, a statistical method is used to quantify the VIIRS LST retrieval uncertainty taking into account the uncertainty from the surface type input. Some issues have been found as follows: (1 Cloud contamination, particularly the cloud detection error over a snow/ice surface, shows significant impacts on LST validation; (2 Performance of the VIIRS LST algorithm is strongly dependent on a correct classification of the surface type; (3 The VIIRS LST quality can be degraded when significant brightness temperature difference between the two split window channels is observed; (4 Surface type dependent algorithm exhibits deficiency in correcting the large emissivity variations within a surface type.

Estimation of the Land Surface Temperature over the Tibetan Plateau by Using Chinese FY-2C Geostationary Satellite Data.

Science.gov (United States)

Hu, Yuanyuan; Zhong, Lei; Ma, Yaoming; Zou, Mijun; Xu, Kepiao; Huang, Ziyu; Feng, Lu

2018-01-28

During the process of land-atmosphere interaction, one of the essential parameters is the land surface temperature (LST). The LST has high temporal variability, especially in its diurnal cycle, which cannot be acquired by polar-orbiting satellites. Therefore, it is of great practical significance to retrieve LST data using geostationary satellites. According to the data of FengYun 2C (FY-2C) satellite and the measurements from the Enhanced Observing Period (CEOP) of the Asia-Australia Monsoon Project (CAMP) on the Tibetan Plateau (CAMP/Tibet), a regression approach was utilized in this research to optimize the split window algorithm (SWA). The thermal infrared data obtained by the Chinese geostationary satellite FY-2C over the Tibetan Plateau (TP) was used to estimate the hourly LST time series. To decrease the effects of cloud, the 10-day composite hourly LST data were obtained through the approach of maximal value composite (MVC). The derived LST was used to compare with the product of MODIS LST and was also validated by the field observation. The results show that the LST retrieved through the optimized SWA and in situ data has a better consistency (with correlation coefficient (R), mean absolute error (MAE), mean bias (MB), and root mean square error (RMSE) values of 0.987, 1.91 K, 0.83 K and 2.26 K, respectively) than that derived from Becker and Li's SWA and MODIS LST product, which means that the modified SWA can be applied to achieve plateau-scale LST. The diurnal variation of the LST and the hourly time series of the LST over the Tibetan Plateau were also obtained. The diurnal range of LST was found to be clearly affected by the influence of the thawing and freezing process of soil and the summer monsoon evolution. The comparison between the seasonal and diurnal variations of LST at four typical underlying surfaces over the TP indicate that the variation of LST is closely connected with the underlying surface types as well. The diurnal variation of LST is

Survey Helps Class to See, Understand Local Standards.

Science.gov (United States)

Pasternack, Steve

1986-01-01

Presents an exercise in which students interview various groups of citizens--church leaders, school officials, government and business leaders--in order to give students a broader understanding of the definitions of obscenity and community standards. (HTH)

Cloud Tolerance of Remote-Sensing Technologies to Measure Land Surface Temperature

Science.gov (United States)

Holmes, Thomas R. H.; Hain, Christopher R.; Anderson, Martha C.; Crow, Wade T.

2016-01-01

Conventional methods to estimate land surface temperature (LST) from space rely on the thermal infrared(TIR) spectral window and is limited to cloud-free scenes. To also provide LST estimates during periods with clouds, a new method was developed to estimate LST based on passive microwave(MW) observations. The MW-LST product is informed by six polar-orbiting satellites to create a global record with up to eight observations per day for each 0.25resolution grid box. For days with sufficient observations, a continuous diurnal temperature cycle (DTC) was fitted. The main characteristics of the DTC were scaled to match those of a geostationary TIR-LST product. This paper tests the cloud tolerance of the MW-LST product. In particular, we demonstrate its stable performance with respect to flux tower observation sites (four in Europe and nine in the United States), over a range of cloudiness conditions up to heavily overcast skies. The results show that TIR based LST has slightly better performance than MW-LST for clear-sky observations but suffers an increasing negative bias as cloud cover increases. This negative bias is caused by incomplete masking of cloud-covered areas within the TIR scene that affects many applications of TIR-LST. In contrast, for MW-LST we find no direct impact of clouds on its accuracy and bias. MW-LST can therefore be used to improve TIR cloud screening. Moreover, the ability to provide LST estimates for cloud-covered surfaces can help expand current clear-sky-only satellite retrieval products to all-weather applications.

Temperature changes in Three Gorges Reservoir Area and linkage with Three Gorges Project

Science.gov (United States)

Song, Zhen; Liang, Shunlin; Feng, Lian; He, Tao; Song, Xiao-Peng; Zhang, Lei

2017-05-01

The Three Gorges Project (TGP) is one of the largest hydroelectric projects throughout the world. It has brought many benefits to the society but also led to endless debates about its environmental and climatic impacts. Monitoring the spatiotemporal variations of temperature in the Three Gorges Reservoir Area (TGRA) is important for understanding the climatic impacts of the TGP. In this study, we used remote sensing-based land surface temperature (LST) and ground-measured air temperature data to investigate temperature changes in the TGRA. Results showed that during the daytime in summer, LST exhibited significant cooling (1-5°C) in the downstream region of the reservoir, whereas LST during the nighttime in winter exhibited significant warming (1-5°C) across the entire reservoir. However, these cooling and warming effects were both locally constrained within 5 km buffer along the reservoir. The changes in air temperature were consistent with those in LST, with 0.67°C cooling in summer and 0.33°C warming in winter. The temperature changes along the reservoir not only resulted from the land-water conversion induced by the dam impounding but were also related to the increase of vegetation cover caused by the ecological restoration projects. Significant warming trends were also found in the upstream of TGRA, especially during the daytime in summer, with up to 5°C for LST and 0.52°C for air temperature. The warming was caused mainly by urban expansion, which was driven in part by the population resettlement of TGP. Based on satellite observations, we investigated the comprehensive climatic impacts of TGP caused by multiple factors.

Bicalutamide 150 mg plus standard care vs standard care alone for early prostate cancer

DEFF Research Database (Denmark)

McLeod, David G; Iversen, Peter; See, William A

2006-01-01

To evaluate, in the ongoing Early Prostate Cancer (EPC) trial programme, the efficacy and tolerability of bicalutamide 150 mg once daily in addition to standard care for localized or locally advanced, nonmetastatic prostate cancer....

Expansion of oil palm and other cash crops causes an increase of the land surface temperature in the Jambi province in Indonesia

Directory of Open Access Journals (Sweden)

C. R. Sabajo

2017-10-01

Full Text Available Indonesia is currently one of the regions with the highest transformation rate of land surface worldwide related to the expansion of oil palm plantations and other cash crops replacing forests on large scales. Land cover changes, which modify land surface properties, have a direct effect on the land surface temperature (LST, a key driver for many ecological functions. Despite the large historic land transformation in Indonesia toward oil palm and other cash crops and governmental plans for future expansion, this is the first study so far to quantify the impacts of land transformation on the LST in Indonesia. We analyze LST from the thermal band of a Landsat image and produce a high-resolution surface temperature map (30 m for the lowlands of the Jambi province in Sumatra (Indonesia, a region which suffered large land transformation towards oil palm and other cash crops over the past decades. The comparison of LST, albedo, normalized differenced vegetation index (NDVI and evapotranspiration (ET between seven different land cover types (forest, urban areas, clear-cut land, young and mature oil palm plantations, acacia and rubber plantations shows that forests have lower surface temperatures than the other land cover types, indicating a local warming effect after forest conversion. LST differences were up to 10.1 ± 2.6 °C (mean ± SD between forest and clear-cut land. The differences in surface temperatures are explained by an evaporative cooling effect, which offsets the albedo warming effect. Our analysis of the LST trend of the past 16 years based on MODIS data shows that the average daytime surface temperature in the Jambi province increased by 1.05 °C, which followed the trend of observed land cover changes and exceeded the effects of climate warming. This study provides evidence that the expansion of oil palm plantations and other cash crops leads to changes in biophysical variables, warming the land surface and thus

Melinda - A custom search engine that provides access to locally-developed content using the HL7 Infobutton standard.

Science.gov (United States)

Wan, Yik-Ki J; Staes, Catherine J

2016-01-01

Healthcare organizations use care pathways to standardize care, but once developed, adoption rates often remain low. One challenge for usage concerns clinicians' difficulty in accessing guidance when it is most needed. Although the HL7 'Infobutton Standard' allows clinicians easier access to external references, access to locally-developed resources often requires clinicians to deviate from their normal electronic health record (EHR) workflow to use another application. To address this gap between internal and external resources, we reviewed the literature and existing practices at the University of Utah Health Care. We identify the requirements to meet the needs of a healthcare enterprise and clinicians, describe the design and development of a prototype to aggregate both internal and external resources from within or outside the EHR, and evaluated strengths and limitations of the prototype. The system is functional but not implemented in a live EHR environment. We suggest next steps and enhancements.

Late Outcomes Following Hypofractionated Conformal Radiotherapy vs. Standard Fractionation for Localized Prostate Cancer: A Nonrandomized Contemporary Comparison

International Nuclear Information System (INIS)

Leborgne, Felix; Fowler, Jack

2009-01-01

Purpose: To study retrospectively late complications and biochemical control in patients treated with three-dimensional conformal external-beam radiotherapy for localized prostate cancer administered using hypofractionation vs. a standard fractionation regimen. The hypofractionation regimen (Hypo) was designed to avoid more late rectal reactions and to be done in half as many treatment sessions. Methods and Materials: Eighty-nine nonrandomized patients chose Hypo delivered in 20 fractions of 3 Gy (n = 52) or 3.15 Gy (n = 37) for a median overall treatment time of 33 days. One hundred thirty comparable patients were contemporaneously treated with standard fractionation to a median dose of 78 Gy delivered over 55 days. The median follow-up time was 49 months (range, 24-73 months). Results: The 5-year actuarial biochemical control rates were 96%, 84%, and 85% for low-, medium-, and high-risk disease in the Hypo group, respectively. The respective rates in the standard fractionation group were 98%, 84%, and 87%, with no statistical difference between the two groups. The rate of rectal Grade 2-4 complications was 5.5% in both treatment groups and of urinary Grade 2-4 complications was 5.6% in the Hypo and 3% in the standard group (p = 0.36). Similarly, there were no statistical differences in the rate of late complications between patients treated with 3 Gy/fraction vs. 3.15 Gy/fraction. Conclusions: Our preliminary results showed that the Hypo regimen is feasible and does not reduce biochemical control compared with standard fractionation. The incidence of late complications was not increased when the tumor normalized total doses at 2Gy/fraction was increased from 77.1 to 83.7 Gy in patients treated with either 3 or 3.15 Gy/fraction in the Hypo group, respectively.

The Achievement Ideology and Top-Down National Standardized Exam Policy in Indonesia: Voices from Local English Teachers

Directory of Open Access Journals (Sweden)

Amirul Mukminin

2013-04-01

Full Text Available The purpose of this qualitative inquiry was to explore and describe the perspectives of local English teachers on the National Standardized Exam [NSE] policy as a high-stakes exam to gauge student performance nationally at four senior high schools in Jambi City, Indonesia. The theoretical framework of the ethics of critique, justice, and care was used to guide this study. Data for this study are collected through a demographic background survey and in-depth interviews with fifteen local English teachers. The demographic data were analyzed descriptively. The interviews data were analyzed using within-case and cross-case displays and analyses. Two salient themes with their subthemes that emerged were (1 negative perspectives on the practices and accuracy of the NSE policy and (2 unintended consequences the NSE policy (curriculum and instruction, teaching and learning, teacher motivation, student motivation, less attention to non-tested disciplines, and widespread cheating. This study provides information for policy makers, school leaders, researchers, and teacher educators to understand how the policy is implemented at the school level. Policy implications are discussed

Land surface temperature downscaling using random forest regression: primary result and sensitivity analysis

Science.gov (United States)

Pan, Xin; Cao, Chen; Yang, Yingbao; Li, Xiaolong; Shan, Liangliang; Zhu, Xi

2018-04-01

The land surface temperature (LST) derived from thermal infrared satellite images is a meaningful variable in many remote sensing applications. However, at present, the spatial resolution of the satellite thermal infrared remote sensing sensor is coarser, which cannot meet the needs. In this study, LST image was downscaled by a random forest model between LST and multiple predictors in an arid region with an oasis-desert ecotone. The proposed downscaling approach was evaluated using LST derived from the MODIS LST product of Zhangye City in Heihe Basin. The primary result of LST downscaling has been shown that the distribution of downscaled LST matched with that of the ecosystem of oasis and desert. By the way of sensitivity analysis, the most sensitive factors to LST downscaling were modified normalized difference water index (MNDWI)/normalized multi-band drought index (NMDI), soil adjusted vegetation index (SAVI)/ shortwave infrared reflectance (SWIR)/normalized difference vegetation index (NDVI), normalized difference building index (NDBI)/SAVI and SWIR/NDBI/MNDWI/NDWI for the region of water, vegetation, building and desert, with LST variation (at most) of 0.20/-0.22 K, 0.92/0.62/0.46 K, 0.28/-0.29 K and 3.87/-1.53/-0.64/-0.25 K in the situation of +/-0.02 predictor perturbances, respectively.

Online Global Land Surface Temperature Estimation from Landsat

Directory of Open Access Journals (Sweden)

David Parastatidis

2017-11-01

Full Text Available This study explores the estimation of land surface temperature (LST for the globe from Landsat 5, 7 and 8 thermal infrared sensors, using different surface emissivity sources. A single channel algorithm is used for consistency among the estimated LST products, whereas the option of using emissivity from different sources provides flexibility for the algorithm’s implementation to any area of interest. The Google Earth Engine (GEE, an advanced earth science data and analysis platform, allows the estimation of LST products for the globe, covering the time period from 1984 to present. To evaluate the method, the estimated LST products were compared against two reference datasets: (a LST products derived from ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer, as higher-level products based on the temperature-emissivity separation approach; (b Landsat LST data that have been independently produced, using different approaches. An overall RMSE (root mean square error of 1.52 °C was observed and it was confirmed that the accuracy of the LST product is dependent on the emissivity; different emissivity sources provided different LST accuracies, depending on the surface cover. The LST products, for the full Landsat 5, 7 and 8 archives, are estimated “on-the-fly” and are available on-line via a web application.

Data content standards in Africa

CSIR Research Space (South Africa)

Cooper, Antony K

2005-04-01

Full Text Available Data content standards tend to be more accessible. Easier to understand. Used directly by many end users. Immediately applicable to Africa. More susceptible to culture and language – Hence, more important to have local standards...

Standardized Flexibility: The Choreography of ICT in Standardization of Service Work

Directory of Open Access Journals (Sweden)

Maria Røhnebæk

2012-12-01

Full Text Available This article is based on a research project that explores the proliferation of infor-mation and communication technology (ICT in public services. Furthermore, the research explores how the enhanced presence of ICT relates to efforts to increas-ingly individualise the service delivery. It can be argued that enhanced individual-isation requires increased levels of discretion and flexibility. At the same time, this flexibility needs to be implemented within a standardized framework to ensure due process and to meet demands for efficiency. As local-level work practices in the public services are increasingly being enabled through ICT, the information systems can thus be seen to offer ‘standardized flexibility’. Hence, the information systems work as both enablers of flexibility and as controllers of the same. This research explores how this duality manifests empirically at the local-level of the Norwegian employment and welfare services (NAV. It focuses on the in-terface of the information systems and local-level employees. In this article, I por-tray the role of the information system, Arena, with regard to how the front-line employees structure and organize their work. This portrayal reveals that the in-formation system reflects an ideal world which is out of tune with local working conditions. The employees are thus facing gaps between the ideals of the system and their actual work context. The main purpose of the paper is to illustrate how the employees deal with this gap; I identify three types of responses and strate-gies. Moreover, I suggest that the relationship between the information systems and different kinds of local responses may be fruitfully analysed by drawing an analogy with choreography and dancing. The second purpose of this article is thus to outline how the metaphor of choreography may provide a suitable theoretical lens for analysing ICT-enabled standardization of work.

LAIT: a local ancestry inference toolkit.

Science.gov (United States)

Hui, Daniel; Fang, Zhou; Lin, Jerome; Duan, Qing; Li, Yun; Hu, Ming; Chen, Wei

2017-09-06

Inferring local ancestry in individuals of mixed ancestry has many applications, most notably in identifying disease-susceptible loci that vary among different ethnic groups. Many software packages are available for inferring local ancestry in admixed individuals. However, most of these existing software packages require specific formatted input files and generate output files in various types, yielding practical inconvenience. We developed a tool set, Local Ancestry Inference Toolkit (LAIT), which can convert standardized files into software-specific input file formats as well as standardize and summarize inference results for four popular local ancestry inference software: HAPMIX, LAMP, LAMP-LD, and ELAI. We tested LAIT using both simulated and real data sets and demonstrated that LAIT provides convenience to run multiple local ancestry inference software. In addition, we evaluated the performance of local ancestry software among different supported software packages, mainly focusing on inference accuracy and computational resources used. We provided a toolkit to facilitate the use of local ancestry inference software, especially for users with limited bioinformatics background.

Derivation and evaluation of land surface temperature from the geostationary operational environmental satellite series

Science.gov (United States)

Fang, Li

The Geostationary Operational Environmental Satellites (GOES) have been continuously monitoring the earth surface since 1970, providing valuable and intensive data from a very broad range of wavelengths, day and night. The National Oceanic and Atmospheric Administration's (NOAA's) National Environmental Satellite, Data, and Information Service (NESDIS) is currently operating GOES-15 and GOES-13. The design of the GOES series is now heading to the 4 th generation. GOES-R, as a representative of the new generation of the GOES series, is scheduled to be launched in 2015 with higher spatial and temporal resolution images and full-time soundings. These frequent observations provided by GOES Image make them attractive for deriving information on the diurnal land surface temperature (LST) cycle and diurnal temperature range (DTR). These parameters are of great value for research on the Earth's diurnal variability and climate change. Accurate derivation of satellite-based LSTs from thermal infrared data has long been an interesting and challenging research area. To better support the research on climate change, the generation of consistent GOES LST products for both GOES-East and GOES-West from operational dataset as well as historical archive is in great demand. The derivation of GOES LST products and the evaluation of proposed retrieval methods are two major objectives of this study. Literature relevant to satellite-based LST retrieval techniques was reviewed. Specifically, the evolution of two LST algorithm families and LST retrieval methods for geostationary satellites were summarized in this dissertation. Literature relevant to the evaluation of satellite-based LSTs was also reviewed. All the existing methods are a valuable reference to develop the GOES LST product. The primary objective of this dissertation is the development of models for deriving consistent GOES LSTs with high spatial and high temporal coverage. Proper LST retrieval algorithms were studied

18 CFR 415.42 - Technical standards.

Science.gov (United States)

2010-04-01

...) Standards used by state and local governments shall conform in principle to Commission standards but may.... Any significant difference shall be reviewed with and subject to approval by the Executive Director...

Seasonal Changing Effect on Airflow and Pollutant Dispersion Characteristics in Urban Street Canyons

Directory of Open Access Journals (Sweden)

Jingliang Dong

2017-02-01

Full Text Available In this study, the effect of seasonal variation on air flow and pollutant dispersion characteristics was numerically investigated. A three-dimensional urban canopy model with unit aspect ratio (H/D = 1 was used to calculate surface temperature distribution in the street canyon. Four representative time events (1000 LST, 1300 LST, 1600 LST and 2000 LST during typical clear summer and winter days were selected to examine the air flow diurnal variation. The results revealed the seasonal variation significantly altered the street canyon microclimate. Compared with the street canyon surface temperature distribution in summer, the winter case showed a more evenly distributed surface temperature. In addition, the summer case showed greater daily temperature fluctuation than that of the winter case. Consequently, distinct pollutant dispersion patterns were observed between summer and winter scenarios, especially for the afternoon (1600 LST and night (2000 LST events. Among all studied time events, the pollutant removal performance of the morning (1000 LST and the night (2000 LST events were more sensitive to the seasonal variation. Lastly, limited natural ventilation performance was found during the summer morning and the winter night, which induced relatively high pollutant concentration along the pedestrian height level.

Land surface temperature retrieval from MODIS and VIRR data in northwest China

International Nuclear Information System (INIS)

Wang, L J; Zuo, H C; Ren, P C; Qiang, B

2014-01-01

By using the Gulang Heterogeneous Underlying Surface Layer Experiment (GHUSLE) data, the accuracy of land surface temperature (LST) in Northwest China retrieved by the Moderate-Resolution Imaging Spectroradiometer(MODIS) and Visible and InfraRed Radiometer(VIRR) data is verified. Furthermore, a new LST algorithm for heterogeneous underlying surface is developed and the LST retrieved by the two remote sensing data using three algorithms are compared with the observed data. Results suggest that the new algorithm is the best one in the case of heterogeneous underlying surface, Kerr algorithm accuracy is not satisfying and Becker algorithm is ranked just ahead Kerr algorithm. Especially, the differences in retrieval accuracy among them are more obvious when using the VIRR data. Compared with the observed LST, the root mean square errors of the LST retrieved by MODIS and VIRR data are the least when using the new algorithm, the specific values are 2.55 K and 3.78 K, respectively. The LST retrieved by MODIS data are closer to observed values and higher than its counterpart retrieved by VIRR data. When the new LST retrieval algorithm used, the LST retrieved by MODIS and VIRR data are the closest

Interannual Variation of the Surface Temperature of Tropical Forests from Satellite Observations

Directory of Open Access Journals (Sweden)

Huilin Gao

2016-01-01

Full Text Available Land surface temperatures (LSTs within tropical forests contribute to climate variations. However, observational data are very limited in such regions. This study used passive microwave remote sensing data from the Special Sensor Microwave/Imager (SSM/I and the Special Sensor Microwave Imager Sounder (SSMIS, providing observations under all weather conditions, to investigate the LST over the Amazon and Congo rainforests. The SSM/I and SSMIS data were collected from 1996 to 2012. The morning and afternoon observations from passive microwave remote sensing facilitate the investigation of the interannual changes of LST anomalies on a diurnal basis. As a result of the variability of cloud cover and the corresponding reduction of solar radiation, the afternoon LST anomalies tend to vary more than the morning LST anomalies. The dominant spatial and temporal patterns for interseasonal variations of the LST anomalies over the tropical rainforest were analyzed. The impacts of droughts and El Niños on this LST were also investigated. Differences between early morning and late afternoon LST anomalies were identified by the remote sensing product, with the morning LST anomalies controlled by humidity (according to comparisons with the National Centers for Environmental Prediction (NCEP reanalysis data.

Insulinlike growth factor I affects ocular development: a study of untreated and treated patients with Laron syndrome.

Science.gov (United States)

Bourla, Dan Haim; Laron, Zvi; Snir, Moshe; Lilos, Pearl; Weinberger, Dov; Axer-Siegel, Ruth

2006-07-01

To evaluate the ocular dimensions in patients with primary growth hormone receptor insensitivity (Laron syndrome [LS]) and to study the effect of supplemental insulinlike growth factor I (IGF-I) on ocular growth. Retrospective case series. Twelve patients with LS, 8 untreated (LS group) and 4 treated (LS-T group) with supplemental IGF-I, and 30 healthy controls. Ocular dimensions and refraction were measured, and a full ophthalmologic examination was performed. Differences in the average ocular dimension data among IGF-I-treated patients, untreated ones, and controls. The average axial length of eyes in the LS group was 21.94 mm (standard deviation [SD], 0.81). Corresponding values for the LS-T and control group eyes were 22.53 mm (SD, 1.74) and 23.20 mm (SD, 1.35) respectively. The average anterior chamber depth of eyes in the LS group was 2.55 mm (SD, 0.26). Corresponding values for eyes in the LS-T and control groups were 3.48 mm (SD, 0.09) and 3.84 mm (SD, 0.16) respectively. The average lens thickness of eyes in the LS group was 4.56 mm (SD, 0.36). Corresponding values for the LS-T and control groups were 3.77 mm (SD, 0.23) and 3.51 mm (SD, 0.25), respectively. The average corneal curvature of eyes in the LS group was 46.9 diopters (D) (SD, 2.32). Corresponding values for the LS-T and control groups were 47.6 D (SD, 2.83) and 44.4 D (SD, 1.5), respectively. Insulinlike growth factor I seems to be an important regulator of ocular growth as documented in patients with primary growth hormone insensitivity. The mechanism of this observation should be investigated further.

Fusion of MODIS and landsat-8 surface temperature images: a new approach.

Science.gov (United States)

Hazaymeh, Khaled; Hassan, Quazi K

2015-01-01

Here, our objective was to develop a spatio-temporal image fusion model (STI-FM) for enhancing temporal resolution of Landsat-8 land surface temperature (LST) images by fusing LST images acquired by the Moderate Resolution Imaging Spectroradiometer (MODIS); and implement the developed algorithm over a heterogeneous semi-arid study area in Jordan, Middle East. The STI-FM technique consisted of two major components: (i) establishing a linear relationship between two consecutive MODIS 8-day composite LST images acquired at time 1 and time 2; and (ii) utilizing the above mentioned relationship as a function of a Landsat-8 LST image acquired at time 1 in order to predict a synthetic Landsat-8 LST image at time 2. It revealed that strong linear relationships (i.e., r2, slopes, and intercepts were in the range 0.93-0.94, 0.94-0.99; and 2.97-20.07) existed between the two consecutive MODIS LST images. We evaluated the synthetic LST images qualitatively and found high visual agreements with the actual Landsat-8 LST images. In addition, we conducted quantitative evaluations of these synthetic images; and found strong agreements with the actual Landsat-8 LST images. For example, r2, root mean square error (RMSE), and absolute average difference (AAD)-values were in the ranges 084-0.90, 0.061-0.080, and 0.003-0.004, respectively.

Estimation of Land Surface Temperature through Blending MODIS and AMSR-E Data with the Bayesian Maximum Entropy Method

Directory of Open Access Journals (Sweden)

Xiaokang Kou

2016-01-01

Full Text Available Land surface temperature (LST plays a major role in the study of surface energy balances. Remote sensing techniques provide ways to monitor LST at large scales. However, due to atmospheric influences, significant missing data exist in LST products retrieved from satellite thermal infrared (TIR remotely sensed data. Although passive microwaves (PMWs are able to overcome these atmospheric influences while estimating LST, the data are constrained by low spatial resolution. In this study, to obtain complete and high-quality LST data, the Bayesian Maximum Entropy (BME method was introduced to merge 0.01° and 0.25° LSTs inversed from MODIS and AMSR-E data, respectively. The result showed that the missing LSTs in cloudy pixels were filled completely, and the availability of merged LSTs reaches 100%. Because the depths of LST and soil temperature measurements are different, before validating the merged LST, the station measurements were calibrated with an empirical equation between MODIS LST and 0~5 cm soil temperatures. The results showed that the accuracy of merged LSTs increased with the increasing quantity of utilized data, and as the availability of utilized data increased from 25.2% to 91.4%, the RMSEs of the merged data decreased from 4.53 °C to 2.31 °C. In addition, compared with the filling gap method in which MODIS LST gaps were filled with AMSR-E LST directly, the merged LSTs from the BME method showed better spatial continuity. The different penetration depths of TIR and PMWs may influence fusion performance and still require further studies.

Analyzing land surface temperature variations during Fogo Island (Cape Verde) 2014-2015 eruption with Landsat 8 images

Science.gov (United States)

Vieira, D.; Teodoro, A.; Gomes, A.

2016-10-01

Land Surface Temperature (LST) is an important parameter related to land surface processes that changes continuously through time. Assessing its dynamics during a volcanic eruption has both environmental and socio-economical interest. Lava flows and other volcanic materials produced and deposited throughout an eruption transform the landscape, contributing to its heterogeneity and altering LST measurements. This paper aims to assess variations of satellite-derived LST and to detect patterns during the latest Fogo Island (Cape Verde) eruption, extending from November 2014 through February 2015. LST data was obtained through four processed Landsat 8 images, focused on the caldera where Pico do Fogo volcano sits. QGIS' plugin Semi-Automatic Classification was used in order to apply atmospheric corrections and radiometric calibrations. The algorithm used to retrieve LST values is a single-channel method, in which emissivity values are known. The absence of in situ measurements is compensated by the use of MODIS sensor-derived LST data, used to compare with Landsat retrieved measurements. LST data analysis shows as expected that the highest LST values are located inside the caldera. High temperature values were also founded on the south-facing flank of the caldera. Although spatial patterns observed on the retrieved data remained roughly the same during the time period considered, temperature values changed throughout the area and over time, as it was also expected. LST values followed the eruption dynamic experiencing a growth followed by a decline. Moreover, it seems possible to recognize areas affected by lava flows of previous eruptions, due to well-defined LST spatial patterns.

Environmental standards as strategic outcomes: A simple model

International Nuclear Information System (INIS)

Bhattacharya, Rabindra N.; Pal, Rupayan

2010-01-01

This paper analyses the strategic nature of choice of environmental standards considering both local and global pollution under alternative regimes of international trade. It also compares and contrasts the strategic equilibrium environmental standards and levels of pollution, local and global, with the world optimum levels. It shows that, in case of open economies, environmental standards can be either strategic substitutes or strategic complements. On the contrary, in case of closed economies, environmental standards are always strategic substitutes. It also shows that the strategic equilibrium environmental standards in case of open economies are higher than the world optimum in certain situations. Whereas, in absence of international trade, countries set, in equilibrium, lower environmental standards than the world optimum. (author)

Improvements of a COMS Land Surface Temperature Retrieval Algorithm Based on the Temperature Lapse Rate and Water Vapor/Aerosol Effect

Directory of Open Access Journals (Sweden)

A-Ra Cho

2015-02-01

Full Text Available The National Meteorological Satellite Center in Korea retrieves land surface temperature (LST by applying the split-window LST algorithm (CSW_v1.0 to Communication, Ocean, and Meteorological Satellite (COMS data. Considerable errors were detected under conditions of high water vapor content or temperature lapse rates during validation with Moderate Resolution Imaging Spectroradiometer (MODIS LST because of the too simplified LST algorithm. In this study, six types of LST retrieval equations (CSW_v2.0 were developed to upgrade the CSW_v1.0. These methods were developed by classifying “dry,” “normal,” and “wet” cases for day and night and considering the relative sizes of brightness temperature difference (BTD values. Similar to CSW_v1.0, the LST retrieved by CSW_v2.0 had a correlation coefficient of 0.99 with the prescribed LST and a slightly larger bias of −0.03 K from 0.00K; the root mean square error (RMSE improved from 1.41 K to 1.39 K. In general, CSW_v2.0 improved the retrieval accuracy compared to CSW_v1.0, especially when the lapse rate was high (mid-day and dawn and the water vapor content was high. The spatial distributions of LST retrieved by CSW_v2.0 were found to be similar to the MODIS LST independently of the season, day/night, and geographic locations. The validation using one year’s MODIS LST data showed that CSW_v2.0 improved the retrieval accuracy of LST in terms of correlations (from 0.988 to 0.989, bias (from −1.009 K to 0.292 K, and RMSEs (from 2.613 K to 2.237 K.

Distinct molecular features of different macroscopic subtypes of colorectal neoplasms.

Directory of Open Access Journals (Sweden)

Kenichi Konda

Full Text Available Colorectal adenoma develops into cancer with the accumulation of genetic and epigenetic changes. We studied the underlying molecular and clinicopathological features to better understand the heterogeneity of colorectal neoplasms (CRNs.We evaluated both genetic (mutations of KRAS, BRAF, TP53, and PIK3CA, and microsatellite instability [MSI] and epigenetic (methylation status of nine genes or sequences, including the CpG island methylator phenotype [CIMP] markers alterations in 158 CRNs including 56 polypoid neoplasms (PNs, 25 granular type laterally spreading tumors (LST-Gs, 48 non-granular type LSTs (LST-NGs, 19 depressed neoplasms (DNs and 10 small flat-elevated neoplasms (S-FNs on the basis of macroscopic appearance.S-FNs showed few molecular changes except SFRP1 methylation. Significant differences in the frequency of KRAS mutations were observed among subtypes (68% for LST-Gs, 36% for PNs, 16% for DNs and 6% for LST-NGs (P<0.001. By contrast, the frequency of TP53 mutation was higher in DNs than PNs or LST-Gs (32% vs. 5% or 0%, respectively (P<0.007. We also observed significant differences in the frequency of CIMP between LST-Gs and LST-NGs or PNs (32% vs. 6% or 5%, respectively (P<0.005. Moreover, the methylation level of LINE-1 was significantly lower in DNs or LST-Gs than in PNs (58.3% or 60.5% vs. 63.2%, P<0.05. PIK3CA mutations were detected only in LSTs. Finally, multivariate analyses showed that macroscopic morphologies were significantly associated with an increased risk of molecular changes (PN or LST-G for KRAS mutation, odds ratio [OR] 9.11; LST-NG or DN for TP53 mutation, OR 5.30; LST-G for PIK3CA mutation, OR 26.53; LST-G or DN for LINE-1 hypomethylation, OR 3.41.We demonstrated that CRNs could be classified into five macroscopic subtypes according to clinicopathological and molecular differences, suggesting that different mechanisms are involved in the pathogenesis of colorectal tumorigenesis.

All-weather Land Surface Temperature Estimation from Satellite Data

Science.gov (United States)

Zhou, J.; Zhang, X.

2017-12-01

Satellite remote sensing, including the thermal infrared (TIR) and passive microwave (MW), provides the possibility to observe LST at large scales. For better modeling the land surface processes with high temporal resolutions, all-weather LST from satellite data is desirable. However, estimation of all-weather LST faces great challenges. On the one hand, TIR remote sensing is limited to clear-sky situations; this drawback reduces its usefulness under cloudy conditions considerably, especially in regions with frequent and/or permanent clouds. On the other hand, MW remote sensing suffers from much greater thermal sampling depth (TSD) and coarser spatial resolution than TIR; thus, MW LST is generally lower than TIR LST, especially at daytime. Two case studies addressing the challenges mentioned previously are presented here. The first study is for the development of a novel thermal sampling depth correction method (TSDC) to estimate the MW LST over barren land; this second study is for the development of a feasible method to merge the TIR and MW LSTs by addressing the coarse resolution of the latter one. In the first study, the core of the TSDC method is a new formulation of the passive microwave radiation balance equation, which allows linking bulk MW radiation to the soil temperature at a specific depth, i.e. the representative temperature: this temperature is then converted to LST through an adapted soil heat conduction equation. The TSDC method is applied to the 6.9 GHz channel in vertical polarization of AMSR-E. Evaluation shows that LST estimated by the TSDC method agrees well with the MODIS LST. Validation is based on in-situ LSTs measured at the Gobabeb site in western Namibia. The results demonstrate the high accuracy of the TSDC method: it yields a root-mean squared error (RMSE) of 2 K and ignorable systematic error over barren land. In the second study, the method consists of two core processes: (1) estimation of MW LST from MW brightness temperature and (2

GlobTemperature

Science.gov (United States)

Ghent, Darren; Remedios, John; Bruniquel, Jerome; Sardou, Olivier; Trigo, Isabel; Merchant, Chris; Bulgin, Claire; Goettsche, Frank; Olesen, Folke; Prigent, Catherine; Pinnock, Simon

2014-05-01

Land surface temperature (LST) is the mean radiative skin temperature of an area of land resulting from the mean balance of solar heating and land-atmosphere cooling fluxes. It is a basic determinant of the terrestrial thermal behaviour, as it controls the effective radiating temperature of the Earth's surface. The sensitivity of LST to soil moisture and vegetation cover means it is an important component in numerous applications. For instance, LST is a key boundary condition in land surface models, which determine the surface to atmosphere fluxes of heat, water and carbon; thus influencing cloud cover, precipitation and atmospheric chemistry predictions within General Circulation Models. Changes in land-surface cover can affect global climate, and also can be identified by changes in their surface temperatures. With the demand of LST data from Earth Observation currently experiencing considerable growth it is important that the users of this data are appropriately engaged by the LST community. The GlobTemperature project under the Data User Element of ESA's 4th Earth Observation Envelope Programme (2013-2017) aims to promote the wider uptake of global-scale satellite LST by the research and operational user communities. As such, the programme of work is focussed on achieving some innovative milestones for LST data which include: detailed global merged geostationary (GEO) and low earth orbit (LEO) data sets with estimates of both clear-sky and under-cloud LST; a first Climate Data Record for LST for the ATSR series of instruments; and the provision of a globally representative and consistent in-situ validation and intercomparison matchup database. Furthermore, the strength of such a venture lies in the coherence and openness of the interactions with the LST and user communities. For instance: detailed user input into the specifications and subsequent testing of the LST data sets; sustained access to data in a user-friendly manner through common data formats; and

Standard deviation of local tallies in global Monte Carlo calculation of nuclear reactor core

International Nuclear Information System (INIS)

Ueki, Taro

2010-01-01

Time series methodology has been studied to assess the feasibility of statistical error estimation in the continuous space and energy Monte Carlo calculation of the three-dimensional whole reactor core. The noise propagation was examined and the fluctuation of track length tallies for local fission rate and power has been formally shown to be represented by the autoregressive moving average process of orders p and p-1 [ARMA(p,p-1)], where p is an integer larger than or equal to two. Therefore, ARMA(p,p-1) fitting was applied to the real standard deviation estimation of the power of fuel assemblies at particular heights. Numerical results indicate that straightforward ARMA(3,2) fitting is promising, but a stability issue must be resolved toward the incorporation in the distributed version of production Monte Carlo codes. The same numerical results reveal that the average performance of ARMA(3,2) fitting is equivalent to that of the batch method with a batch size larger than 100 and smaller than 200 cycles for a 1,100 MWe pressurized water reactor. (author)

Aktéři lokálního rozvoje a jejich vzájemná spolupráce

Czech Academy of Sciences Publication Activity Database

Bernard, Josef

2009-01-01

Roč. 7, č. 2 (2009), s. 8-10 ISSN 1214-1720 R&D Projects: GA MŠk 2D06006 Institutional research plan: CEZ:AV0Z70280505 Keywords : local development * urban sociology * social networks Subject RIV: AO - Sociology, Demography http://www.socioweb.cz/index.php?disp=teorie&shw=379&lst=106

7 CFR 225.17 - Procurement standards.

Science.gov (United States)

2010-01-01

...) Procurements by public sponsors comply with applicable State or local laws and the standards set forth in 7 CFR part 3016; and (2) Procurements by private nonprofit sponsors comply with standards set forth in 7 CFR... 7 Agriculture 4 2010-01-01 2010-01-01 false Procurement standards. 225.17 Section 225.17...

Analysis of the Relationship between Land Surface Temperature and Wildfire Severity in a Series of Landsat Images

Directory of Open Access Journals (Sweden)

Lidia Vlassova

2014-06-01

Full Text Available The paper assesses spatio-temporal patterns of land surface temperature (LST and fire severity in the Las Hurdes wildfire of Pinus pinaster forest, which occurred in July 2009, in Extremadura (Spain, from a time series of fifteen Landsat 5 TM images corresponding to 27 post-fire months. The differenced Normalized Burn Ratio (dNBR was used to evaluate burn severity. The mono-window algorithm was applied to estimate LST from the Landsat thermal band. The burned zones underwent a significant increase in LST after fire. Statistically significant differences have been detected between the LST within regions of burn severity categories. More substantial changes in LST are observed in zones of greater fire severity, which can be explained by the lower emissivity of combustion products found in the burned area and changes in the energy balance related to vegetation removal. As time progresses over the 27 months after fire, LST differences decrease due to vegetation regeneration. The differences in LST and Normalized Difference Vegetation Index (NDVI values between burn severity categories in each image are highly correlated (r = 0.84. Spatial patterns of severity and post-fire LST obtained from Landsat time series enable an evaluation of the relationship between these variables to predict the natural dynamics of burned areas.

Relationship among land surface temperature and LUCC, NDVI in typical karst area.

Science.gov (United States)

Deng, Yuanhong; Wang, Shijie; Bai, Xiaoyong; Tian, Yichao; Wu, Luhua; Xiao, Jianyong; Chen, Fei; Qian, Qinghuan

2018-01-12

Land surface temperature (LST) can reflect the land surface water-heat exchange process comprehensively, which is considerably significant to the study of environmental change. However, research about LST in karst mountain areas with complex topography is scarce. Therefore, we retrieved the LST in a karst mountain area from Landsat 8 data and explored its relationships with LUCC and NDVI. The results showed that LST of the study area was noticeably affected by altitude and underlying surface type. In summer, abnormal high-temperature zones were observed in the study area, perhaps due to karst rocky desertification. LSTs among different land use types significantly differed with the highest in construction land and the lowest in woodland. The spatial distributions of NDVI and LST exhibited opposite patterns. Under the spatial combination of different land use types, the LST-NDVI feature space showed an obtuse-angled triangle shape and showed a negative linear correlation after removing water body data. In summary, the LST can be retrieved well by the atmospheric correction model from Landsat 8 data. Moreover, the LST of the karst mountain area is controlled by altitude, underlying surface type and aspect. This study provides a reference for land use planning, ecological environment restoration in karst areas.

Why We Should Establish a National System of Standards.

Science.gov (United States)

Hennen, Thomas J., Jr.

2000-01-01

Explains the need to establish a national system of standards for public libraries. Discusses local standards, state standards, and international standards, and suggests adopting a tiered approach including three levels: minimum standards; target standards; and benchmarking standards, as found in total quality management. (LRW)

A Useful Tool for Atmospheric Correction and Surface Temperature Estimation of Landsat Infrared Thermal Data

Science.gov (United States)

Rivalland, Vincent; Tardy, Benjamin; Huc, Mireille; Hagolle, Olivier; Marcq, Sébastien; Boulet, Gilles

2016-04-01

implemented in LANDARTs and propose a local and spatial validation of the LST products from Landsat dataset archive over two climatically contrasted zones: south-west France and centre of Tunisia. In both sites, long term datasets of in-situ surface temperature measurements have been compared to LST obtained for Landsat data processed by LANDARTs and filtered from clouds. This temporal comparison presents RMSE between 1.84K and 2.55K. Then, Landsat LST products are compared to ASTER kinetic surface temperature products on two synchronous dates from both zones. This comparison presents satisfactory RMSE about 2.55K with a good correlation coefficient of 0.9. Finally, a sensibility analysis to the spatial variation of parameters presents a variability reaching 2K at the Landsat image scale and confirms the improved accuracy in Landsat LST estimation linked to our spatial approach.

Increased radiosensitivity of a subpopulation of T-lymphocyte progenitors from patients with Fanconi's anemia

International Nuclear Information System (INIS)

Knox, S.J.; Wilson, F.D.; Greenberg, B.R.; Shifrine, M.; Rosenblatt, L.S.; Reeves, J.D.; Misra, H.

1981-01-01

In vitro radiation survival of peripheral blood T lymphocytes was studied in 15 clinically normal adults and 4 patients with Fanconi's anemia. Tritiated thymidine incorporation in a whole blood lymphocyte stimulation test (LST) and a newly developed whole blood T-lymphocyte colony assay were used to measure lymphocyte blastogenesis and colony formation in response to phytohemagglutinin (PHA) or concanavalin-A (Con-A) stimulation. Lymphocyte colony formation was found to be consistently more sensitive than the LST for detection of low-level radiation effects using both normal cells and lymphocytes from Fanconi's anemia patients. Lymphocytes from patients with Fanconi's anemia were significantly more sensitive to in vitro x irradiation than lymphocytes from clinically normal individuals as measured by their ability to divide when stimulated by PHA in the LST and colony formation assay. No significant difference in the radiosensitivity of the Con-A response was observed between the two groups. The PHA-responsive T-lymphocyte subpopulation in Fanconi's anemia patients appears to be intrinsically defective. The nature of this defect, significance in the disease process, and relevancy of these findings to the establishment of radiation protection standards are discussed

Remote Sensing of Urban Land Cover/Land Use Change, Surface Thermal Responses, and Potential Meteorological and Climate Change Impacts

Science.gov (United States)

Quattrochi, Dale A.; Jedlovec, Gary; Meyer, Paul

2011-01-01

City growth influences the development of the urban heat island (UHI), but the effect that local meteorology has on the UHI is less well known. This paper presents some preliminary findings from a study that uses multitemporal Landsat TM and ASTER data to evaluate land cover/land use change (LULCC) over the NASA Marshall Space Flight Center (MFSC) and its Huntsville, AL metropolitan area. Landsat NLCD data for 1992 and 2001 have been used to evaluate LULCC for MSFC and the surrounding urban area. Land surface temperature (LST) and emissivity derived from NLCD data have also been analyzed to assess changes in these parameters in relation to LULCC. Additionally, LULCC, LST, and emissivity have been identified from ASTER data from 2001 and 2011 to provide a comparison with the 2001 NLCD and as a measure of current conditions within the study area. As anticipated, the multi-temporal NLCD and ASTER data show that significant changes have occurred in land covers, LST, and emissivity within and around MSFC. The patterns and arrangement of these changes, however, is significant because the juxtaposition of urban land covers within and outside of MSFC provides insight on what impacts at a local to regional scale, the inter-linkage of these changes potentially have on meteorology. To further analyze these interactions between LULCC, LST, and emissivity with the lower atmosphere, a network of eleven weather stations has been established across the MSFC property. These weather stations provide data at a 10 minute interval, and these data are uplinked for use by MSFC facilities operations and the National Weather Service. The weather data are also integrated within a larger network of meteorological stations across north Alabama. Given that the MSFC weather stations will operate for an extended period of time, they can be used to evaluate how the building of new structures, and changes in roadways, and green spaces as identified in the MSFC master plan for the future, will

Recent Upgrades to NASA SPoRT Initialization Datasets for the Environmental Modeling System

Science.gov (United States)

Case, Jonathan L.; Lafontaine, Frank J.; Molthan, Andrew L.; Zavodsky, Bradley T.; Rozumalski, Robert A.

2012-01-01

The NASA Short-term Prediction Research and Transition (SPoRT) Center has developed several products for its NOAA/National Weather Service (NWS) partners that can initialize specific fields for local model runs within the NOAA/NWS Science and Training Resource Center Environmental Modeling System (EMS). The suite of SPoRT products for use in the EMS consists of a Sea Surface Temperature (SST) composite that includes a Lake Surface Temperature (LST) analysis over the Great Lakes, a Great Lakes sea-ice extent within the SST composite, a real-time Green Vegetation Fraction (GVF) composite, and NASA Land Information System (LIS) gridded output. This paper and companion poster describe each dataset and provide recent upgrades made to the SST, Great Lakes LST, GVF composites, and the real-time LIS runs.

General Urban Warfare Amphibious Logistics Applications. Volume 1. Technical Report.

Science.gov (United States)

1983-06-23

condiments , tea, powdered milk, etc., but these will probably he available in the local economy. If not, and if a determination i. made to provide any of...March, 1978, pp. 78-83. Marsh, LtCol J.O., McCormick , lstLt M., et al. "Combat Support: Shore Party and Logistics; Engineer; Communications Air

HISTORICAL GIS DATA AND CHANGES IN URBAN MORPHOLOGICAL PARAMETERS FOR THE ANALYSIS OF URBAN HEAT ISLANDS IN HONG KONG

Directory of Open Access Journals (Sweden)

F. Peng

2016-06-01

Full Text Available Rapid urban development between the 1960 and 2010 decades have changed the urban landscape and pattern in the Kowloon Peninsula of Hong Kong. This paper aims to study the changes of urban morphological parameters between the 1985 and 2010 and explore their influences on the urban heat island (UHI effect. This study applied a mono-window algorithm to retrieve the land surface temperature (LST using Landsat Thematic Mapper (TM images from 1987 to 2009. In order to estimate the effects of local urban morphological parameters to LST, the global surface temperature anomaly was analysed. Historical 3D building model was developed based on aerial photogrammetry technique using aerial photographs from 1964 to 2010, in which the urban digital surface models (DSMs including elevations of infrastructures and buildings have been generated. Then, urban morphological parameters (i.e. frontal area index (FAI, sky view factor (SVF, vegetation fractional cover (VFC, global solar radiation (GSR, Normalized Difference Built-Up Index (NDBI, wind speed were derived. Finally, a linear regression method in Waikato Environment for Knowledge Analysis (WEKA was used to build prediction model for revealing LST spatial patterns. Results show that the final apparent surface temperature have uncertainties less than 1 degree Celsius. The comparison between the simulated and actual spatial pattern of LST in 2009 showed that the correlation coefficient is 0.65, mean absolute error (MAE is 1.24 degree Celsius, and root mean square error (RMSE is 1.51 degree Celsius of 22,429 pixels.

An Efficient Approach for Pixel Decomposition to Increase the Spatial Resolution of Land Surface Temperature Images from MODIS Thermal Infrared Band Data

Directory of Open Access Journals (Sweden)

Fei Wang

2014-12-01

Full Text Available Land surface temperature (LST images retrieved from the thermal infrared (TIR band data of Moderate Resolution Imaging Spectroradiometer (MODIS have much lower spatial resolution than the MODIS visible and near-infrared (VNIR band data. The coarse pixel scale of MODIS LST images (1000 m under nadir have limited their capability in applying to many studies required high spatial resolution in comparison of the MODIS VNIR band data with pixel scale of 250–500 m. In this paper we intend to develop an efficient approach for pixel decomposition to increase the spatial resolution of MODIS LST image using the VNIR band data as assistance. The unique feature of this approach is to maintain the thermal radiance of parent pixels in the MODIS LST image unchanged after they are decomposed into the sub-pixels in the resulted image. There are two important steps in the decomposition: initial temperature estimation and final temperature determination. Therefore the approach can be termed double-step pixel decomposition (DSPD. Both steps involve a series of procedures to achieve the final result of decomposed LST image, including classification of the surface patterns, establishment of LST change with normalized difference of vegetation index (NDVI and building index (NDBI, reversion of LST into thermal radiance through Planck equation, and computation of weights for the sub-pixels of the resulted image. Since the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER with much higher spatial resolution than MODIS data was on-board the same platform (Terra as MODIS for Earth observation, an experiment had been done in the study to validate the accuracy and efficiency of our approach for pixel decomposition. The ASTER LST image was used as the reference to compare with the decomposed LST image. The result showed that the spatial distribution of the decomposed LST image was very similar to that of the ASTER LST image with a root mean square error

An efficient approach for pixel decomposition to increase the spatial resolution of land surface temperature images from MODIS thermal infrared band data.

Science.gov (United States)

Wang, Fei; Qin, Zhihao; Li, Wenjuan; Song, Caiying; Karnieli, Arnon; Zhao, Shuhe

2014-12-25

Land surface temperature (LST) images retrieved from the thermal infrared (TIR) band data of Moderate Resolution Imaging Spectroradiometer (MODIS) have much lower spatial resolution than the MODIS visible and near-infrared (VNIR) band data. The coarse pixel scale of MODIS LST images (1000 m under nadir) have limited their capability in applying to many studies required high spatial resolution in comparison of the MODIS VNIR band data with pixel scale of 250-500 m. In this paper we intend to develop an efficient approach for pixel decomposition to increase the spatial resolution of MODIS LST image using the VNIR band data as assistance. The unique feature of this approach is to maintain the thermal radiance of parent pixels in the MODIS LST image unchanged after they are decomposed into the sub-pixels in the resulted image. There are two important steps in the decomposition: initial temperature estimation and final temperature determination. Therefore the approach can be termed double-step pixel decomposition (DSPD). Both steps involve a series of procedures to achieve the final result of decomposed LST image, including classification of the surface patterns, establishment of LST change with normalized difference of vegetation index (NDVI) and building index (NDBI), reversion of LST into thermal radiance through Planck equation, and computation of weights for the sub-pixels of the resulted image. Since the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) with much higher spatial resolution than MODIS data was on-board the same platform (Terra) as MODIS for Earth observation, an experiment had been done in the study to validate the accuracy and efficiency of our approach for pixel decomposition. The ASTER LST image was used as the reference to compare with the decomposed LST image. The result showed that the spatial distribution of the decomposed LST image was very similar to that of the ASTER LST image with a root mean square error (RMSE) of 2

Meteorological and sulphur dioxide dispersion modelling for an industrial complex near Mexico city metropolitan area

International Nuclear Information System (INIS)

Mora, V.R.; Sosa, G.; Molina, M.M.; Palmerin-ruiz, M.E.; Melgarejo-flores, L.E.

2009-01-01

Major sulphur dioxide emissions in Mexico are due largely to fuel of oil refining and coal combustion. In Tula-Vito-Apasco industrial corridor (TVA) are located two important sources of SO/sub 2/: the 'Miguel Hidalgo' refinery and the 'Francisco Perez Rios' power plant. Due to from March 25 to April 22 of 2006 a major field campaign took place as part of a collaborative research program called MILAGRO. Data collected around the Industrial Complex were used to: a) evaluate the air quality to local and regional scale; b) study the structure of the atmospheric boundary layer (BL); and c) validate meteorological and dispersion models. In this study we presented the behaviour of daytime BL, and the results of meteorological and dispersion modelling for selected episodes of high sulfur dioxide (SO/sub 2/). The Regional Atmospheric Modeling System (RAMS) and the Hybrid and Particle Concentration Transport Model (HYPACT) were used to evaluate the impact of SO/sub 2/ emissions to regional scale. For modelling, we selected the days where higher mean daily levels of SO/sub 2 /surface concentrations were observed, these corresponded to March 31 and April 6. The results indicate that: The daytime BL in TVA, exhibited a normal behavior, a stable layer or thermal inversion close to surface was observed at 0800 LST (up to 80% of the cases), then the mixing height (MH) growths, with a growth rate of 313 m h-1 (between 0800 to 1200 LST). The most rapid MH growth happened between 1200 to 1500 LST;. The maximum MH was observed at 1500 LST (90% of the cases); the mean maximum MH was close to 2794 m AGL; Potential temperature and humidity profiles showed a normal behavior; High persistence in wind direction (> 0.6) close to surface up to 500 m AGL, was observed at 1500, and 1800 LST, at the same time, a low level jet, penetrating from the NE, with wind speed between 6 to 8 m s/sup -1/ was observed. Meteorological modelling was used to determine the circulation patterns in the region

Seasonal Changing Effect on Airflow and Pollutant Dispersion Characteristics in Urban Street Canyons

OpenAIRE

Jingliang Dong; Zijing Tan; Yimin Xiao; Jiyuan Tu

2017-01-01

In this study, the effect of seasonal variation on air flow and pollutant dispersion characteristics was numerically investigated. A three-dimensional urban canopy model with unit aspect ratio (H/D = 1) was used to calculate surface temperature distribution in the street canyon. Four representative time events (1000 LST, 1300 LST, 1600 LST and 2000 LST) during typical clear summer and winter days were selected to examine the air flow diurnal variation. The results revealed the seasonal variat...

Terminally Ill Taiwanese Cancer Patients' and Family Caregivers' Agreement on Patterns of Life-Sustaining Treatment Preferences Is Poor to Fair and Declines Over a Decade: Results From Two Independent Cross-Sectional Studies.

Science.gov (United States)

Liu, Tsang-Wu; Wen, Fur-Hsing; Wang, Cheng-Hsu; Hong, Ruey-Long; Chow, Jyh-Ming; Chen, Jen-Shi; Chiu, Chang-Fang; Tang, Siew Tzuh

2017-07-01

Temporal changes have not been examined in patient-caregiver agreement on life-sustaining treatment (LST) preferences at end of life (EOL). We explored the extent of and changes in patient-caregiver agreement on LST-preference patterns for two independent cohorts of Taiwanese cancer patient-family caregiver dyads recruited a decade apart. We surveyed preferences for cardiopulmonary resuscitation, intensive care unit care, cardiac massage, intubation with mechanical ventilation, intravenous nutritional support, tube feeding, and dialysis among 1049 and 1901 dyads in 2003-2004 and 2011-2012, respectively. LST-preference patterns were examined by multi-group latent class analysis. Extent of patient-caregiver agreement on LST-preference patterns was determined by percentage agreement and kappa coefficients. For both patients and family caregivers, we identified seven distinct LST-preference classes. Patient-caregiver agreement on LST-preference patterns was poor to fair across both study cohorts, indicated by 24.4%-43.5% agreement and kappa values of 0.06 (95% CI: 0.04, 0.09) to 0.27 (0.23, 0.30), and declined significantly over time. Agreement on LST-preference patterns was most likely when both patients and caregivers uniformly rejected LSTs. When patients disagreed with caregivers on LST-preference patterns, discrepancies were most likely when patients totally rejected LSTs but caregivers uniformly preferred LSTs or preferred nutritional support but rejected other treatments. Patients and family caregivers had poor-to-fair agreement on LST-preference patterns, and agreement declined significantly over a decade. Encouraging an open dialogue between patients and their family caregivers about desired EOL care would facilitate patient-caregiver agreement on LST-preference patterns, thus honoring terminally ill cancer patients' wishes when they cannot make EOL-care decisions. Copyright © 2017 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc

MODELLING THE RELATIONSHIP BETWEEN LAND SURFACE TEMPERATURE AND LANDSCAPE PATTERNS OF LAND USE LAND COVER CLASSIFICATION USING MULTI LINEAR REGRESSION MODELS

Directory of Open Access Journals (Sweden)

A. M. Bernales

2016-06-01

Full Text Available The threat of the ailments related to urbanization like heat stress is very prevalent. There are a lot of things that can be done to lessen the effect of urbanization to the surface temperature of the area like using green roofs or planting trees in the area. So land use really matters in both increasing and decreasing surface temperature. It is known that there is a relationship between land use land cover (LULC and land surface temperature (LST. Quantifying this relationship in terms of a mathematical model is very important so as to provide a way to predict LST based on the LULC alone. This study aims to examine the relationship between LST and LULC as well as to create a model that can predict LST using class-level spatial metrics from LULC. LST was derived from a Landsat 8 image and LULC classification was derived from LiDAR and Orthophoto datasets. Class-level spatial metrics were created in FRAGSTATS with the LULC and LST as inputs and these metrics were analysed using a statistical framework. Multi linear regression was done to create models that would predict LST for each class and it was found that the spatial metric “Effective mesh size” was a top predictor for LST in 6 out of 7 classes. The model created can still be refined by adding a temporal aspect by analysing the LST of another farming period (for rural areas and looking for common predictors between LSTs of these two different farming periods.

On the sensitivity of Land Surface Temperature estimates in arid irrigated lands using MODTRAN

KAUST Repository

Rosas, Jorge

2015-11-29

Land surface temperature (LST) derived from thermal infrared (TIR) satellite data has been reliably used as a remote indicator of evapotranspiration (ET) and surface moisture status. However, in order to retrieve the ET with an accuracy approaching 10%, LST should be retrieved to within 1 ◦C or better, disregarding other elements of uncertainty. The removal of atmospheric effects is key towards achieving a precise estimation of LST and it requires detailed information on water vapor. The Thermal Infrared Sensor (TIRS) onboard Landsat 8 captures data in two long wave thermal bands with 100-meter resolution. However, the US Geological Survey has reported a calibration problem of TIRS bands caused by stray light, resulting in a higher bias in one of its two bands (4% in band 11, 2% in band 10). Therefore, split-window algorithms for the estimation of LST might not be reliable. Our work will focus on the impact of using different atmospheric profiles (e.g. weather prediction models, satellite) for the estimation of LST derived from MODTRAN by using one of the TIRS bands onboard Landsat 8 (band 10). Sites with in-situ measurements of LST are used as evaluation sources. Comparisons between the measured LST and LST derived based on different atmospheric profile inputs to MODTRAN are carried out from 2 Landsat-overpass days (DOY 153 and 160 2015). Preliminary results show a mean absolute error of around 3 ◦C between in-situ and estimated LST over two different crops (alfalfa and carrot) and bare soil.

Jak nejlépe vychovávat – „optimální výchova“

Czech Academy of Sciences Publication Activity Database

Vojtíšková, Kateřina

2011-01-01

Roč. 9, č. 4 (2011), s. 5-6 ISSN 1214-1720 R&D Projects: GA MŠk 2D06014 Institutional research plan: CEZ:AV0Z70280505 Keywords : parental style * history * expert standards Subject RIV: AO - Sociology, Demography http://www.socioweb.cz/index.php?disp=temata&shw=374&lst=116

A case of standardization?

DEFF Research Database (Denmark)

Rod, Morten Hulvej; Høybye, Mette Terp

2016-01-01

the ones envisioned by the makers of standards. In 2012, the Danish National Health Authorities introduced a set of health promotion guidelines that were meant to guide the decision making and priority setting of Denmark's 98 local governments. The guidelines provided recommendations for health promotion...... and standardization. It remains an open question whether or not the guidelines lead to more standardized policies and interventions, but we suggest that the guidelines promote a risk factor-oriented approach as the dominant frame for knowledge, reasoning, decision making and priority setting in health promotion. We...

Evaluation of Land Surface Temperature Operationally Retrieved from Korean Geostationary Satellite (COMS Data

Directory of Open Access Journals (Sweden)

A-Ra Cho

2013-08-01

Full Text Available We evaluated the precision of land surface temperature (LST operationally retrieved from the Korean multipurpose geostationary satellite, Communication, Ocean and Meteorological Satellite (COMS. The split-window (SW-type retrieval algorithm was developed through radiative transfer model simulations under various atmospheric profiles, satellite zenith angles, surface emissivity values and surface lapse rate conditions using Moderate Resolution Atmospheric Transmission version 4 (MODTRAN4. The estimation capabilities of the COMS SW (CSW LST algorithm were evaluated for various impacting factors, and the retrieval accuracy of COMS LST data was evaluated with collocated Moderate Resolution Imaging Spectroradiometer (MODIS LST data. The surface emissivity values for two SW channels were generated using a vegetation cover method. The CSW algorithm estimated the LST distribution reasonably well (averaged bias = 0.00 K, Root Mean Square Error (RMSE = 1.41 K, correlation coefficient = 0.99; however, the estimation capabilities of the CSW algorithm were significantly impacted by large brightness temperature differences and surface lapse rates. The CSW algorithm reproduced spatiotemporal variations of LST comparing well to MODIS LST data, irrespective of what month or time of day the data were collected from. The one-year evaluation results with MODIS LST data showed that the annual mean bias, RMSE and correlation coefficient for the CSW algorithm were −1.009 K, 2.613 K and 0.988, respectively.

Data converters for wireless standards

CERN Document Server

Shi, Chunlei

2002-01-01

Wireless communication is witnessing tremendous growth with proliferation of different standards covering wide, local and personal area networks (WAN, LAN and PAN). The trends call for designs that allow 1) smooth migration to future generations of wireless standards with higher data rates for multimedia applications, 2) convergence of wireless services allowing access to different standards from the same wireless device, 3) inter-continental roaming. This requires designs that work across multiple wireless standards, can easily be reused, achieve maximum hardware share at a minimum power consumption levels particularly for mobile battery-operated devices.

Control system architecture: The standard and non-standard models

International Nuclear Information System (INIS)

Thuot, M.E.; Dalesio, L.R.

1993-01-01

Control system architecture development has followed the advances in computer technology through mainframes to minicomputers to micros and workstations. This technology advance and increasingly challenging accelerator data acquisition and automation requirements have driven control system architecture development. In summarizing the progress of control system architecture at the last International Conference on Accelerator and Large Experimental Physics Control Systems (ICALEPCS) B. Kuiper asserted that the system architecture issue was resolved and presented a ''standard model''. The ''standard model'' consists of a local area network (Ethernet or FDDI) providing communication between front end microcomputers, connected to the accelerator, and workstations, providing the operator interface and computational support. Although this model represents many present designs, there are exceptions including reflected memory and hierarchical architectures driven by requirements for widely dispersed, large channel count or tightly coupled systems. This paper describes the performance characteristics and features of the ''standard model'' to determine if the requirements of ''non-standard'' architectures can be met. Several possible extensions to the ''standard model'' are suggested including software as well as the hardware architectural feature

The Relationship Between State and District Content Standards:Issues of Alignment, Influence and Utility

Directory of Open Access Journals (Sweden)

Elizabeth Dutro

2004-08-01

Full Text Available At the core of standards-based reform are content standards--statements about what students should know and be able to do. Although it is state standards that are the focus of much public attention and consume substantial resources, many local school districts have developed their own content standards in the major subject areas. However, we know very little about the role state standards have played in local standards efforts. In this article we report on a study of the relationship between state and local content standards in reading in four states and districts. Through interviews with key personnel in each state, and district and analyses of state and local content standards in reading, we explored the alignment between state and district content standards, the path of influence between the two, and the role of high-stakes tests in state and districts reform efforts. Our findings suggest that alignment had multiple meanings and that state standards had differential utility to districts, ranging from helpful to benign to nuisance. This wide variability was influenced by the nature of the standards themselves, the state vision of alignment and local control, districts’ own engagement and commitment to professional development, and student performance on high-stakes tests. We explore implications for the future of content standards as the cornerstone of standards-based reform and argue that states must promote district ownership and expand accountability if state content standards are to have any relevance for local efforts to reform teaching and learning.

The Langley Stability and Transition Analysis Code (LASTRAC) : LST, Linear and Nonlinear PSE for 2-D, Axisymmetric, and Infinite Swept Wing Boundary Layers

Science.gov (United States)

Chang, Chau-Lyan

2003-01-01

During the past two decades, our understanding of laminar-turbulent transition flow physics has advanced significantly owing to, in a large part, the NASA program support such as the National Aerospace Plane (NASP), High-speed Civil Transport (HSCT), and Advanced Subsonic Technology (AST). Experimental, theoretical, as well as computational efforts on various issues such as receptivity and linear and nonlinear evolution of instability waves take part in broadening our knowledge base for this intricate flow phenomenon. Despite all these advances, transition prediction remains a nontrivial task for engineers due to the lack of a widely available, robust, and efficient prediction tool. The design and development of the LASTRAC code is aimed at providing one such engineering tool that is easy to use and yet capable of dealing with a broad range of transition related issues. LASTRAC was written from scratch based on the state-of-the-art numerical methods for stability analysis and modem software technologies. At low fidelity, it allows users to perform linear stability analysis and N-factor transition correlation for a broad range of flow regimes and configurations by using either the linear stability theory (LST) or linear parabolized stability equations (LPSE) method. At high fidelity, users may use nonlinear PSE to track finite-amplitude disturbances until the skin friction rise. Coupled with the built-in receptivity model that is currently under development, the nonlinear PSE method offers a synergistic approach to predict transition onset for a given disturbance environment based on first principles. This paper describes the governing equations, numerical methods, code development, and case studies for the current release of LASTRAC. Practical applications of LASTRAC are demonstrated for linear stability calculations, N-factor transition correlation, non-linear breakdown simulations, and controls of stationary crossflow instability in supersonic swept wing boundary

Cloud tolerance of remote sensing technologies to measure land surface temperature

Science.gov (United States)

Conventional means to estimate land surface temperature (LST) from space relies on the thermal infrared (TIR) spectral window and is limited to cloud-free scenes. To also provide LST estimates during periods with clouds, a new method was developed to estimate LST based on passive microwave (MW) obse...

Validity of Standing Posture Eight-electrode Bioelectrical Impedance to Estimate Body Composition in Taiwanese Elderly

Directory of Open Access Journals (Sweden)

Ling-Chun Lee

2014-09-01

Conclusion: The results of this study showed that the impedance index and LST in the whole body, upper limbs, and lower limbs derived from DXA findings were highly correlated. The LST and BF% estimated by BIA8 in whole body and various body segments were highly correlated with the corresponding DXA results; however, BC-418 overestimates the participants' appendicular LST and underestimates whole body BF%. Therefore, caution is needed when interpreting the results of appendicular LST and whole body BF% estimated for elderly adults.

Causal quantum theory and the collapse locality loophole

International Nuclear Information System (INIS)

Kent, Adrian

2005-01-01

Causal quantum theory is an umbrella term for ordinary quantum theory modified by two hypotheses: state vector reduction is a well-defined process, and strict local causality applies. The first of these holds in some versions of Copenhagen quantum theory and need not necessarily imply practically testable deviations from ordinary quantum theory. The second implies that measurement events which are spacelike separated have no nonlocal correlations. To test this prediction, which sharply differs from standard quantum theory, requires a precise definition of state vector reduction. Formally speaking, any precise version of causal quantum theory defines a local hidden variable theory. However, causal quantum theory is most naturally seen as a variant of standard quantum theory. For that reason it seems a more serious rival to standard quantum theory than local hidden variable models relying on the locality or detector efficiency loopholes. Some plausible versions of causal quantum theory are not refuted by any Bell experiments to date, nor is it evident that they are inconsistent with other experiments. They evade refutation via a neglected loophole in Bell experiments--the collapse locality loophole--which exists because of the possible time lag between a particle entering a measurement device and a collapse taking place. Fairly definitive tests of causal versus standard quantum theory could be made by observing entangled particles separated by ≅0.1 light seconds

Double Compressions of Atmospheric Depth by Geopotential Tendency, Vorticity, and Atmospheric Boundary Layer Affected Abrupt High Particulate Matter Concentrations at a Coastal City for a Yellow Dust Period in October

Directory of Open Access Journals (Sweden)

Hyo Choi

2014-01-01

Full Text Available Using GRIMM-aerosol sampler, NOAA-HYSPLIT model, and 3D-WRF-3.3 model, the transportation of dusts from Gobi Desert toward Gangneung city, Korea was investigated from 09:00 LST October 27 to 04:00 LST October 28, 2003. Maximum PM10 (PM2.5, PM1 concentration was detected with 3.8 (3.4, 14.1 times higher magnitude than one in non-Yellow Dust period. The combination of dusts transported from the desert under westerly wind with particulate matters and gases from vehicles on the road of the city caused high PM concentrations near the ground surface at 09:00 LST and their maxima at 17:00 LST near sunset with further pollutants from heating boilers in the resident area. Positive geopotential tendency at the 500 hPa level of the city (∂Φ/∂t; m day−1 corresponding to negative vorticity of -4×10-5 sec−1 (-2.5×10-5 sec−1 at 0900 LST (21:00 LST; at night was +83 m day−1 (+30 m day−1 and it caused atmospheric depth between 500 hPa level and the ground surface to be vertically expanded. However, its net reduction to −53 m/12 hrs until 21:00 LST indicated synoptic-scale atmospheric layer to be vertical shrunken, resulting in the increase of PM concentrations at 17:00 LST. Simultaneously, much shallower microscale stable nocturnal surface inversion layer (NSIL than daytime thermal internal boundary layer induced particulate matters to be merged inside the NSIL, resulting in maximum PM concentrations at 17:00 LST.

ANALYSIS OF RELATIONSHIP BETWEEN URBAN HEAT ISLAND EFFECT AND LAND USE/COVER TYPE USING LANDSAT 7 ETM+ AND LANDSAT 8 OLI IMAGES

Directory of Open Access Journals (Sweden)

N. Aslan

2016-06-01

Full Text Available The main objectives of this study are (i to calculate Land Surface Temperature (LST from Landsat imageries, (ii to determine the UHI effects from Landsat 7 ETM+ (June 5, 2001 and Landsat 8 OLI (June 17, 2014 imageries, (iii to examine the relationship between LST and different Land Use/Land Cover (LU/LC types for the years 2001 and 2014. The study is implemented in the central districts of Antalya. Initially, the brightness temperatures are retrieved and the LST values are calculated from Landsat thermal images. Then, the LU/LC maps are created from Landsat pan-sharpened images using Random Forest (RF classifier. Normalized Difference Vegetation Index (NDVI image, ASTER Global Digital Elevation Model (GDEM and DMSP_OLS nighttime lights data are used as auxiliary data during the classification procedure. Finally, UHI effect is determined and the LST values are compared with LU/LC classes. The overall accuracies of RF classification results were computed higher than 88 % for both Landsat images. During 13-year time interval, it was observed that the urban and industrial areas were increased significantly. Maximum LST values were detected for dry agriculture, urban, and bareland classes, while minimum LST values were detected for vegetation and irrigated agriculture classes. The UHI effect was computed as 5.6 °C for 2001 and 6.8 °C for 2014. The validity of the study results were assessed using MODIS/Terra LST and Emissivity data and it was found that there are high correlation between Landsat LST and MODIS LST data (r2 = 0.7 and r2 = 0.9 for 2001 and 2014, respectively.

Patient-related factors and circumstances surrounding decisions to forego life-sustaining treatment, including intensive care unit admission refusal.

Science.gov (United States)

Reignier, Jean; Dumont, Romain; Katsahian, Sandrine; Martin-Lefevre, Laurent; Renard, Benoit; Fiancette, Maud; Lebert, Christine; Clementi, Eva; Bontemps, Frederic

2008-07-01

To assess decisions to forego life-sustaining treatment (LST) in patients too sick for intensive care unit (ICU) admission, comparatively to patients admitted to the ICU. Prospective observational cohort study. A medical-surgical ICU. Consecutive patients referred to the ICU during a one-yr period. None. Of 898 triaged patients, 147 were deemed too well to benefit from ICU admission. Decisions to forego LST were made in 148 of 666 (22.2%) admitted patients and in all 85 patients deemed too sick for ICU admission. Independent predictors of decisions to forego LST at ICU refusal rather than after ICU admission were: age; underlying disease; living in an institution; preexisting cognitive impairment; admission for medical reasons; and acute cardiac failure, acute central neurologic illness, or sepsis. Hospital mortality after decisions to forego LST was not significantly different in refused and admitted patients (77.5% vs. 86.5%; p = .1). Decisions to forego LST were made via telephone in 58.8% of refused patients and none of the admitted patients. Nurses caring for the patient had no direct contact with the ICU physicians for 62.3% of the decisions in refused patients, whereas meetings between nurses and physicians occurred in 70.3% of decisions to forego LST in the ICU. Patients or relatives were involved in 28.2% of decisions to forego LST at ICU refusal compared with 78.4% of decisions to forego LST in ICU patients (p refused patients (vs. none of admitted patients) and were associated with less involvement of nurses and relatives compared with decisions in admitted patients. Further work is needed to improve decisions to forego LST made under the distinctive circumstances of triage.

Performance standard-based validation study for local lymph node assay: 5-bromo-2-deoxyuridine-flow cytometry method.

Science.gov (United States)

Ahn, Ilyoung; Kim, Tae-Sung; Jung, Eun-Sun; Yi, Jung-Sun; Jang, Won-Hee; Jung, Kyoung-Mi; Park, Miyoung; Jung, Mi-Sook; Jeon, Eun-Young; Yeo, Kyeong-Uk; Jo, Ji-Hoon; Park, Jung-Eun; Kim, Chang-Yul; Park, Yeong-Chul; Seong, Won-Keun; Lee, Ai-Young; Chun, Young Jin; Jeong, Tae Cheon; Jeung, Eui Bae; Lim, Kyung-Min; Bae, SeungJin; Sohn, Soojung; Heo, Yong

2016-10-01

Local lymph node assay: 5-bromo-2-deoxyuridine-flow cytometry method (LLNA: BrdU-FCM) is a modified non-radioisotopic technique with the additional advantages of accommodating multiple endpoints with the introduction of FCM, and refinement and reduction of animal use by using a sophisticated prescreening scheme. Reliability and accuracy of the LLNA: BrdU-FCM was determined according to OECD Test Guideline (TG) No. 429 (Skin Sensitization: Local Lymph Node Assay) performance standards (PS), with the participation of four laboratories. Transferability was demonstrated through successfully producing stimulation index (SI) values for 25% hexyl cinnamic aldehyde (HCA) consistently greater than 3, a predetermined threshold, by all participating laboratories. Within- and between-laboratory reproducibility was shown using HCA and 2,4-dinitrochlorobenzene, in which EC2.7 values (the estimated concentrations eliciting an SI of 2.7, the threshold for LLNA: BrdU-FCM) fell consistently within the acceptance ranges, 0.025-0.1% and 5-20%, respectively. Predictive capacity was tested using the final protocol version 1.3 for the 18 reference chemicals listed in OECD TG 429, of which results showed 84.6% sensitivity, 100% specificity, and 88.9% accuracy compared with the original LLNA. The data presented are considered to meet the performance criteria for the PS, and its predictive capacity was also sufficiently validated. Copyright © 2016 Elsevier Inc. All rights reserved.

Seasonal Variations of the Surface Urban Heat Island in a Semi-Arid City

Directory of Open Access Journals (Sweden)

Sirous Haashemi

2016-04-01

Full Text Available The process of the surface urban heat island (SUHI varies with latitude, climate, topography and meteorological conditions. This study investigated the seasonal variability of SUHI in the Tehran metropolitan area, Iran, with respect to selected surface biophysical variables. Terra Moderate Resolution Imaging Spectroradiometer (MODIS Land Surface Temperature (LST was retrieved as nighttime LST data, while daytime LST was retrieved from Landsat 8 Thermal Infrared Sensor (TIRS using the split-window algorithm. Both data covered the time period from September 2013 to September 2015. To assess SUHI intensity, we employed three SUHI indicators, i.e., the LST difference of urban-rural, that of urban-agriculture and that of urban-water. Physical and biophysical surface variables, including land use and land cover (LULC, elevation, impervious surface (IS, fractional vegetation cover (FVC and albedo, were selected to estimate the relationship between LST seasonal variability and the surface properties. Results show that an inversion of the SUHI phenomenon (i.e., surface urban cool island existed at daytime with the maximal value of urban-rural LST difference of −4 K in March; whereas the maximal value of SUHI at nighttime yielded 3.9 K in May. When using the indicators of urban-agriculture and urban-water LST differences, the maximal value of SUHI was found to be 8.2 K and 15.5 K, respectively. Both results were observed at daytime, suggesting the role of bare soils in the inversion of the SUHI phenomenon with the urban-rural indicator. Maximal correlation was observed in the relationship between night LST and elevation in spring (coefficient: −0.76, night LST and IS in spring (0.60, night LST and albedo in winter (−0.53 and day LST with fractional vegetation cover in summer (−0.41. The relationship between all surface properties with LST possessed large seasonal variations, and thus, using these relationships for SUHI modeling may not be

Chemical compatibility and properties of suspension plasma-sprayed SrTiO3-based anodes for intermediate-temperature solid oxide fuel cells

Science.gov (United States)

Zhang, Shan-Lin; Li, Cheng-Xin; Li, Chang-Jiu

2014-10-01

La-doped strontium titanate (LST) is a promising, redox-stable perovskite material for direct hydrocarbon oxidation anodes in intermediate-temperature solid oxide fuel cells (IT-SOFCs). In this study, nano-sized LST and Sm-doped ceria (SDC) powders are produced by the sol-gel and glycine-nitrate processes, respectively. The chemical compatibility between LST and electrolyte materials is studied. A LST-SDC composite anode is prepared by suspension plasma spraying (SPS). The effects of annealing conditions on the phase structure, microstructure, and chemical stability of the LST-SDC composite anode are investigated. The results indicate that the suspension plasma-sprayed LST-SDC anode has the same phase structure as the original powders. LST exhibits a good chemical compatibility with SDC and Mg/Sr-doped lanthanum gallate (LSGM). The anode has a porosity of ∼40% with a finely porous structure that provides high gas permeability and a long three-phase boundary for the anode reaction. Single cells assembled with the LST-SDC anode, La0.8Sr0.2Ga0.8Mg0.2O3 electrolyte, and La0.8Sr0.2CoO3-SDC cathode show a good performance at 650-800 °C. The annealing reduces the impedances due to the enhancement in the bonding between the particles in the anode and interface of anode and LSGM electrolyte, thus improving the output performance of the cell.

The urban heat island in Rio de Janeiro, Brazil, in the last 30 years using remote sensing data

Science.gov (United States)

Peres, Leonardo de Faria; Lucena, Andrews José de; Rotunno Filho, Otto Corrêa; França, José Ricardo de Almeida

2018-02-01

The aim of this work is to study urban heat island (UHI) in Metropolitan Area of Rio de Janeiro (MARJ) based on the analysis of land-surface temperature (LST) and land-use patterns retrieved from Landsat-5/Thematic Mapper (TM), Landsat-7/Enhanced Thematic Mapper Plus (ETM+) and Landsat-8/Operational Land Imager (OLI) and Thermal Infrared Sensors (TIRS) data covering a 32-year period between 1984 and 2015. LST temporal evolution is assessed by comparing the average LST composites for 1984-1999 and 2000-2015 where the parametric Student t-test was conducted at 5% significance level to map the pixels where LST for the more recent period is statistically significantly greater than the previous one. The non-parametric Mann-Whitney-Wilcoxon rank sum test has also confirmed at the same 5% significance level that the more recent period (2000-2015) has higher LST values. UHI intensity between ;urban; and ;rural/urban low density; (;vegetation;) areas for 1984-1999 and 2000-2015 was established and confirmed by both parametric and non-parametric tests at 1% significance level as 3.3 °C (5.1 °C) and 4.4 °C (7.1 °C), respectively. LST has statistically significantly (p-value analysis was also performed to identify the urban pixels within MARJ where UHI is more intense by subtracting the LST of these pixels from the LST mean value of ;vegetation; land-use class.

Quantifying the Trends in Land Surface Temperature and Surface Urban Heat Island Intensity in Mediterranean Cities in View of Smart Urbanization

Directory of Open Access Journals (Sweden)

Anastasios Polydoros

2018-02-01

Full Text Available Land Surface Temperature (LST is a key parameter for the estimation of urban fluxes as well as for the assessment of the presence and strength of the surface urban heat island (SUHI. In an urban environment, LST depends on the way the city has been planned and developed over time. To this end, the estimation of LST needs adequate spatial and temporal data at the urban scale, especially with respect to land cover/land use. The present study is divided in two parts: at first, satellite data from MODIS-Terra 8-day product (MOD11A2 were used for the analysis of an eighteen-year time series (2001–2017 of the LST spatial and temporal distribution in five major cities of the Mediterranean during the summer months. LST trends were retrieved and assessed for their statistical significance. Secondly, LST values and trends for each city were examined in relation to land cover characteristics and patterns in order to define the contribution of urban development and planning on LST; this information is important for the drafting of smart urbanization policies and measures. Results revealed (a positive LST trends in the urban areas especially during nighttime ranging from +0.412 °K in Marseille to +0.923 °K in Cairo and (b the SUHI has intensified during the last eighteen years especially during daytime in European Mediterranean cities, such as Rome (+0.332 °K and Barcelona (+0.307 °K.

A Standardized Generalized Dimensionality Discrepancy Measure and a Standardized Model-Based Covariance for Dimensionality Assessment for Multidimensional Models

Science.gov (United States)

Levy, Roy; Xu, Yuning; Yel, Nedim; Svetina, Dubravka

2015-01-01

The standardized generalized dimensionality discrepancy measure and the standardized model-based covariance are introduced as tools to critique dimensionality assumptions in multidimensional item response models. These tools are grounded in a covariance theory perspective and associated connections between dimensionality and local independence.…

Stability Analysis of Hypersonic Boundary Layer over a Cone at Small Angle of Attack

Directory of Open Access Journals (Sweden)

Feng Ji

2014-04-01

Full Text Available An investigation on the stability of hypersonic boundary layer over a cone at small angle of attack has been performed. After obtaining the steady base flow, linear stability theory (LST analysis has been made with local parallel assumption. The growth rates of the first mode and second mode waves at different streamwise locations and different azimuthal angles are obtained. The results show that the boundary layer stability was greatly influenced by small angles of attack. The maximum growth rate of the most unstable wave on the leeward is larger than that on the windward. Moreover, dominating second mode wave starts earlier on the leeward than that on the windward. The LST result also shows that there is a “valley” region around 120°~150° meridian in the maximum growth rates curve.

LEAST SQUARE APPROACH FOR ESTIMATING OF LAND SURFACE TEMPERATURE FROM LANDSAT-8 SATELLITE DATA USING RADIATIVE TRANSFER EQUATION

Directory of Open Access Journals (Sweden)

Y. Jouybari-Moghaddam

2017-09-01

Full Text Available Land Surface Temperature (LST is one of the significant variables measured by remotely sensed data, and it is applied in many environmental and Geoscience studies. The main aim of this study is to develop an algorithm to retrieve the LST from Landsat-8 satellite data using Radiative Transfer Equation (RTE. However, LST can be retrieved from RTE, but, since the RTE has two unknown parameters including LST and surface emissivity, estimating LST from RTE is an under the determined problem. In this study, in order to solve this problem, an approach is proposed an equation set includes two RTE based on Landsat-8 thermal bands (i.e.: band 10 and 11 and two additional equations based on the relation between the Normalized Difference Vegetation Index (NDVI and emissivity of Landsat-8 thermal bands by using simulated data for Landsat-8 bands. The iterative least square approach was used for solving the equation set. The LST derived from proposed algorithm is evaluated by the simulated dataset, built up by MODTRAN. The result shows the Root Mean Squared Error (RMSE is less than 1.18°K. Therefore; the proposed algorithm can be a suitable and robust method to retrieve the LST from Landsat-8 satellite data.

Least Square Approach for Estimating of Land Surface Temperature from LANDSAT-8 Satellite Data Using Radiative Transfer Equation

Science.gov (United States)

Jouybari-Moghaddam, Y.; Saradjian, M. R.; Forati, A. M.

2017-09-01

Land Surface Temperature (LST) is one of the significant variables measured by remotely sensed data, and it is applied in many environmental and Geoscience studies. The main aim of this study is to develop an algorithm to retrieve the LST from Landsat-8 satellite data using Radiative Transfer Equation (RTE). However, LST can be retrieved from RTE, but, since the RTE has two unknown parameters including LST and surface emissivity, estimating LST from RTE is an under the determined problem. In this study, in order to solve this problem, an approach is proposed an equation set includes two RTE based on Landsat-8 thermal bands (i.e.: band 10 and 11) and two additional equations based on the relation between the Normalized Difference Vegetation Index (NDVI) and emissivity of Landsat-8 thermal bands by using simulated data for Landsat-8 bands. The iterative least square approach was used for solving the equation set. The LST derived from proposed algorithm is evaluated by the simulated dataset, built up by MODTRAN. The result shows the Root Mean Squared Error (RMSE) is less than 1.18°K. Therefore; the proposed algorithm can be a suitable and robust method to retrieve the LST from Landsat-8 satellite data.

Diurnal and Seasonal Variation of Surface Urban Cool and Heat Islands in the Semi-Arid City of Erbil, Iraq

Directory of Open Access Journals (Sweden)

Azad Rasul

2016-09-01

Full Text Available The influence of land surface temperature (LST makes the near-surface layer of the troposphere a key driver of urban climate. This paper assesses the temporal formation of the daytime Surface Urban Cool Island (SUCI and night-time Surface Urban Heat Island (SUHI effect in Erbil, Iraq, situated in a semi-arid climate region. LST retrievals from the Moderate Resolution Imaging Spectroradiometer (MODIS Aqua and Terra and MODIS Normalized Difference Vegetation Index (NDVI from January 2003 to December 2014 are analysed. The relationships of LST with NDVI and the Normalized Multi-band Drought Index (NMDI are investigated in order to assess the influence of vegetation and moisture on the observed patterns of LST and the SUCI/SUHI. The results indicate that during the daytime, in summer, autumn and winter, densely built-up areas had lower LST acting as a SUCI compared to the non-urbanised area around the city. In contrast, at night-time, Erbil experienced higher LST and demonstrated a significant SUHI effect. The relationship between LST and NDVI is affected by seasonality and is strongly inverted during spring (r2 = 0.73; p < 0.01. Contrary to previous studies of semi-arid cities, a SUCI was detected, not only in the morning, but also during the afternoon.

Spatial Modeling of Urban Vegetation and Land Surface Temperature: A Case Study of Beijing

Directory of Open Access Journals (Sweden)

Chudong Huang

2015-07-01

Full Text Available The coupling relationship between urban vegetation and land surface temperature (LST has been heatedly debated in a variety of environmental studies. This paper studies the urban vegetation information and LST by utilizing a series of remote sensing imagery covering the period from 1990 to 2007. Their coupling relationship is analyzed, in order to provide the basis for ecological planning and environment protection. The results show that the normalized difference vegetation index (NDVI, urban vegetation abundance (UVA and urban forest abundance (UFA are negatively correlated with LST, which means that both urban vegetation and urban forest are capable in decreasing LST. The apparent influence of urban vegetation and urban forest on LST varies with the spatial resolution of the imagery, and peaks at the resolutions ranging from 90 m to 120 m.

A multistate examination of partnership activity among local public health systems using the National Public Health Performance Standards.

Science.gov (United States)

Barnes, Priscilla A; Curtis, Amy B; Hall-Downey, Laura; Moonesinghe, Ramal

2012-01-01

This study examines whether partnership-related measures in the second version of the National Public Health Performance Standards (NPHPS) are useful in evaluating level of activity as well as identifying latent constructs that exist among local public health systems (LPHSs). In a sample of 110 LPHSs, descriptive analysis was conducted to determine frequency and percentage of 18 partnership-related NPHPS measures. Principal components factor analysis was conducted to identify unobserved characteristics that promote effective partnerships among LPHSs. Results revealed that 13 of the 18 measures were most frequently reported at the minimal-moderate level (conducted 1%-49% of the time). Coordination of personal health and social services to optimize access (74.6%) was the most frequently reported measure at minimal-moderate levels. Optimal levels (conducted >75% of the time) were reported most frequently in 2 activities: participation in emergency preparedness coalitions and local health departments ensuring service provision by working with state health departments (67% and 61% of respondents, respectively) and the least optimally reported activity was review partnership effectiveness (4% of respondents). Factor analysis revealed categories of partnership-related measures in 4 domains: resources and activities contributing to relationship building, evaluating community leadership activities, research, and state and local linkages to support public health activities. System-oriented public health assessments may have questions that serve as proxy measures to examine levels of interorganizational partnerships. Several measures from the NPHPS were useful in establishing a national baseline of minimal and optimal activity levels as well as identifying factors to enhance the delivery of the 10 essential public health services among organizations and individuals in public health systems.

Local anesthetic effects of Lidocaine cream: randomized controlled trial using a standardized prick pain.

Science.gov (United States)

Herberger, Katharina; Krause, Karoline; Maier, Kristina; Zschocke, Ina; Radtke, Marc; Augustin, Matthias

2012-12-01

ELA-max (4% lidocaine) and EMLA cream (lidocaine-prilocaine 2.5%) are topicals used for superficial anesthesia. Only few studies have been published on their comparative effectiveness in close-to-practice pain models. (1) To evaluate the analgesic efficacy of lidocaine cream compared with lidocaine-prilocaine cream and placebo. (2) To assess the safety and tolerability. Randomized, three-arm, double-blind trial in 40 healthy volunteers comparing the anesthetic effects of Lidocaine and lidocaine-prilocaine cream to placebo at various time points (0-120 min). A standardized pain was induced by lancet pricks and measured by a visual analogue scale. Intra-individual comparison between the test areas was performed in a cross-over design. Lidocaine showed significantly reduced pain compared to placebo at all assessment points. Pain reduction was achieved significantly earlier using lidocaine occlusively (30 min). No significant differences were found concerning the anesthetic efficacy of lidocaine and lidocaine-prilocaine cream. There were no relevant adverse events. This study confirms that a topical preparation with 4% lidocaine is an effective and safe treatment option for superficial anesthesia. It supports the claim that an occlusive application is more rapid in action. 4% lidocaine is of value as a rapidly-acting local anesthetic for the treatment of minor surgical procedures.

Radical prostatectomy in the 21st century - the gold standard for localized and locally advanced prostate cancer.

Science.gov (United States)

Schostak, M; Miller, K; Schrader, M

2008-01-01

Radical prostatectomy for treatment of prostate cancer is a technically sophisticated operation. Simpler therapies have therefore been developed in the course of decades. The decisive advantage of a radical operation is the chance of a cure with minimal collateral damage. It is the only approach that enables precise tumor staging. The 10-year progression-free survival probability is approximately 85% for a localized tumor with negative resection margins. This high cure rate is unsurpassed by competitive treatment modalities. Nowadays, experienced surgeons achieve excellent functional results (for example, recovery of continence and erectile function) with minimum morbidity. Even in the locally advanced stage, results are very good compared to those obtained with other treatment modalities. Pathological staging enables stratified adjuvant therapy based on concrete information. The overall prognosis can thus be significantly improved.

Increased radiosensitivity of a subpopulation ot T-lymphocyte progenitors from patients with Fanconi's anemia

International Nuclear Information System (INIS)

Knox, S.J.; Wilson, F.D.; Greenberg, B.R.; Shifrine, M.; Rosenblatt, L.S.; Reeves, J.D.; Misra, H.

1981-01-01

In vitro radiation survival of peripheral blood T lymphocytes was studied in 15 clinically normal adults and 4 patients with Fanconi's anemia. Tritiated thymidine incorporation in a whole blood lymphocyte stimulation test (LST) and a newly developed whole blood T-lymphocyte colony assay were used to measure lymphocyte blastogenesis and colony formation in response to phytohemagglutinin (PHA) or concanavalin-A (Con-A) stimulation. Lymphocyte colony formation was found to be consistently more sensitive than the LST for detection of low-level radiation effects using both normal cells and lymphocytes from Fanconi's anemia patients. Lymphocytes from patients with Fanconi's anemia were significantly more sensitive to in vitro x-irradiation than lymphocytes from clinically normal individuals as measured by their ability to divide when stimulated by PHA in the LST (patients, D37 . 198 R; normals, D37 . 309 R, p . 0.057) and colony formation assay (patients, D37 . 53 R; normals, D37 . 109 R, p . 0.016). No significant difference in the radiosensitivity of the Con-A response was observed between the two groups. The PHA-responsive T-lymphocyte subpopulation in Fanconi's anemia patients appears to be intrinsically defective. The nature of this defect, significance in the disease process, and relevancy of these findings to the establishment of radiation protection standards are discussed

Binary trading relations and the limits of EDI standards

DEFF Research Database (Denmark)

Damsgaard, Jan; Truex, D.

2000-01-01

This paper provides a critical examination of electronic data interchange (EDI) standards and their application in different types of trading relationships. It argues that EDI standards are not directly comparable to more stable sets of technical standards in that they are dynamically tested...... and negotiated in use with each trading exchange. It takes the position that EDI standards are an emergent language form and must mean different things at the institutional and local levels. Using the lens of emergent linguistic analysis it shows how the institutional and local levels must always be distinct...... and yet can coexist. EDI standards can never represent the creation of an 'Esperanto of institutional communication'. Instead we believe that standards must be developed such that they support and accommodate general basic grammatical forms that can be customised to individual needs. The analysis...

40 CFR 35.6550 - Procurement system standards.

Science.gov (United States)

2010-07-01

... referred to the local, State, Tribal, or Federal authority having proper jurisdiction. (5) Selection... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Procurement system standards. 35.6550... ASSISTANCE STATE AND LOCAL ASSISTANCE Cooperative Agreements and Superfund State Contracts for Superfund...

Estimating Daily Maximum and Minimum Land Air Surface Temperature Using MODIS Land Surface Temperature Data and Ground Truth Data in Northern Vietnam

Directory of Open Access Journals (Sweden)

Phan Thanh Noi

2016-12-01

Full Text Available This study aims to evaluate quantitatively the land surface temperature (LST derived from MODIS (Moderate Resolution Imaging Spectroradiometer MOD11A1 and MYD11A1 Collection 5 products for daily land air surface temperature (Ta estimation over a mountainous region in northern Vietnam. The main objective is to estimate maximum and minimum Ta (Ta-max and Ta-min using both TERRA and AQUA MODIS LST products (daytime and nighttime and auxiliary data, solving the discontinuity problem of ground measurements. There exist no studies about Vietnam that have integrated both TERRA and AQUA LST of daytime and nighttime for Ta estimation (using four MODIS LST datasets. In addition, to find out which variables are the most effective to describe the differences between LST and Ta, we have tested several popular methods, such as: the Pearson correlation coefficient, stepwise, Bayesian information criterion (BIC, adjusted R-squared and the principal component analysis (PCA of 14 variables (including: LST products (four variables, NDVI, elevation, latitude, longitude, day length in hours, Julian day and four variables of the view zenith angle, and then, we applied nine models for Ta-max estimation and nine models for Ta-min estimation. The results showed that the differences between MODIS LST and ground truth temperature derived from 15 climate stations are time and regional topography dependent. The best results for Ta-max and Ta-min estimation were achieved when we combined both LST daytime and nighttime of TERRA and AQUA and data from the topography analysis.

Effect of land cover and green space on land surface temperature of a fast growing economic region in Malaysia

Science.gov (United States)

Sheikhi, A.; Kanniah, K. D.; Ho, C. H.

2015-10-01

Green space must be increased in the development of new cities as green space can moderate temperature in the cities. In this study we estimated the land surface temperature (LST) and established relationships between LST and land cover and various vegetation and urban surface indices in the Iskandar Malaysia (IM) region. IM is one of the emerging economic gateways of Malaysia, and is envisaged to transform into a metropolis by 2025. This change may cause increased temperature in IM and therefore we conducted a study by using Landsat 5 image covering the study region (2,217 km2) to estimate LST, classify different land covers and calculate spectral indices. Results show that urban surface had highest LST (24.49 °C) and the lowest temperature was recorded in, forest, rubber and water bodies ( 20.69 to 21.02°C). Oil palm plantations showed intermediate mean LST values with 21.65 °C. We further investigated the relationship between vegetation and build up densities with temperature. We extracted 1000 collocated pure pixels of Normalized Difference Vegetation Index (NDVI), Normalized Difference Water Index (NDWI), Normalized Difference Built-up Index (NDBI), Urban Index (UI) and LST in the study area. Results show a strong and significant negative correlation with (R2= -0.74 and -0.79) respectively between NDVI, NDWI and LST . Meanwhile a strong positive correlation (R2=0.8 and 0.86) exists between NDBI, UI and LST. These results show the importance of increasing green cover in urban environment to combat any adverse effects of climate change.

Establishment and characterization of a new cell line derived from human colorectal laterally spreading tumor

Science.gov (United States)

Wang, Xin-Ying; Lai, Zhou-Sheng; Yeung, Chung-Man; Wang, Ji-De; Deng, Wen; Li, Hoi Yee; Han, Yu-Jing; Kung, Hsiang-Fu; Jiang, Bo; Lin, Marie Chia-mi

2008-01-01

AIM: To study the molecular mechanism of laterally spreading tumor (LST), a cell line [Laterally Spreading Tumor-Rectum 1 (LST-R1)] was derived and the characteristics of this cell line were investigated. METHODS: A new cell line (LST-R1) originated from laterally spreading tumor was established. Properties of the cell line were characterized using scanning and transmission electron microscopy, immunohistochemistry method, cytogenetic analysis and nude mice xenograft experiments. In vitro invasion assay, cDNA microarray and Western blotting were used to compare the difference between the LST-R1 and other colorectal cancer cell lines derived from prudent colon cancer. RESULTS: Our study demonstrated that both epithelial special antigen (ESA) and cytokeratin-20 (CK20) were expressed in LST-R1. The cells presented microvilli and tight junction with large nuclei. The karyotypic analysis showed hyperdiploid features with structural chromosome aberrations. The in vivo tumorigenicity was also demonstrated in nude mice xenograft experiments. The invasion assay suggested this cell line has a higher invasive ability. cDNA microarray and Western blotting show the loss of the expression of E-cadherin in LST-R1 cells. CONCLUSION: We established and characterized a colorectal cancer cell line, LST-R1 and LST-R1 has an obvious malignant tendency, which maybe partially attributed to the changes of the expression of some adhesion molecules, such as E-cadherin. It is also a versatile tool for exploring the original and progressive mechanisms of laterally spreading tumor and the early colon cancer genesis. PMID:18300345

Local properties of analytic functions and non-standard analysis

International Nuclear Information System (INIS)

O'Brian, N.R.

1976-01-01

This is an expository account which shows how the methods of non-standard analysis can be applied to prove the Nullstellensatz for germs of analytic functions. This method of proof was discovered originally by Abraham Robinson. The necessary concepts from model theory are described in some detail and the Nullstellensatz is proved by investigating the relation between the set of infinitesimal elements in the complex n-plane and the spectrum of the ring of germs of analytic functions. (author)

Long Term Validation of Land Surface Temperature Retrieved from MSG/SEVIRI with Continuous in-Situ Measurements in Africa

Directory of Open Access Journals (Sweden)

Frank-M. Göttsche

2016-05-01

Full Text Available Since 2005, the Land Surface Analysis Satellite Application Facility (LSA SAF operationally retrieves Land Surface Temperature (LST for the Spinning Enhanced Visible and Infrared Imager (SEVIRI on board Meteosat Second Generation (MSG. The high temporal resolution of the Meteosat satellites and their long term availability since 1977 make their data highly valuable for climate studies. In order to ensure that the LSA SAF LST product continuously meets its target accuracy of 2 °C, it is validated with in-situ measurements from four dedicated LST validation stations. Three stations are located in highly homogenous areas in Africa (semiarid bush, desert, and Kalahari semi-desert and typically provide thousands of monthly match-ups with LSA SAF LST, which are used to perform seasonally resolved validations. An uncertainty analysis performed for desert station Gobabeb yielded an estimate of total in-situ LST uncertainty of 0.8 ± 0.12 °C. Ignoring rainy seasons, the results for the period 2009–2014 show that LSA SAF LST consistently meets its target accuracy: the highest mean root-mean-square error (RMSE for LSA SAF LST over the African stations was 1.6 °C while mean absolute bias was 0.1 °C. Nighttime and daytime biases were up to 0.7 °C but had opposite signs: when evaluated together, these partially compensated each other.

The evolution of a clinical database: from local to standardized clinical languages.

OpenAIRE

Prophet, C. M.

2000-01-01

For more than twenty years, the University of Iowa Hospitals and Clinics Nursing Informatics (UIHC NI) has been developing a clinical database to support patient care planning and documentation in the INFORMM NIS (Information Network for Online Retrieval & Medical Management Nursing Information System). Beginning in 1992, the database content was revised to standardize orders and to incorporate the Standardized Nursing Languages (SNLs) of the North American Nursing Diagnosis Association (NAND...

Withholding or withdrawing of life-sustaining therapy in older adults (≥ 80 years) admitted to the intensive care unit.

Science.gov (United States)

Guidet, Bertrand; Flaatten, Hans; Boumendil, Ariane; Morandi, Alessandro; Andersen, Finn H; Artigas, Antonio; Bertolini, Guido; Cecconi, Maurizio; Christensen, Steffen; Faraldi, Loredana; Fjølner, Jesper; Jung, Christian; Marsh, Brian; Moreno, Rui; Oeyen, Sandra; Öhman, Christina Agwald; Pinto, Bernardo Bollen; Soliman, Ivo W; Szczeklik, Wojciech; Valentin, Andreas; Watson, Ximena; Zafeiridis, Tilemachos; De Lange, Dylan W

2018-05-17

To document and analyse the decision to withhold or withdraw life-sustaining treatment (LST) in a population of very old patients admitted to the ICU. This prospective study included intensive care patients aged ≥ 80 years in 309 ICUs from 21 European countries with 30-day mortality follow-up. LST limitation was identified in 1356/5021 (27.2%) of patients: 15% had a withholding decision and 12.2% a withdrawal decision (including those with a previous withholding decision). Patients with LST limitation were older, more frail, more severely ill and less frequently electively admitted. Patients with withdrawal of LST were more frequently male and had a longer ICU length of stay. The ICU and 30-day mortality were, respectively, 29.1 and 53.1% in the withholding group and 82.2% and 93.1% in the withdrawal group. LST was less frequently limited in eastern and southern European countries than in northern Europe. The patient-independent factors associated with LST limitation were: acute ICU admission (OR 5.77, 95% CI 4.32-7.7), Clinical Frailty Scale (CFS) score (OR 2.08, 95% CI 1.78-2.42), increased age (each 5 years of increase in age had a OR of 1.22 (95% CI 1.12-1.34) and SOFA score [OR of 1.07 (95% CI 1.05-1.09 per point)]. The frequency of LST limitation was higher in countries with high GDP and was lower in religious countries. The most important patient variables associated with the instigation of LST limitation were acute admission, frailty, age, admission SOFA score and country. ClinicalTrials.gov (ID: NTC03134807).

Technical Review of Law Enforcement Standards and Guides Relative to Incident Management

Energy Technology Data Exchange (ETDEWEB)

Stenner, Robert D.; Salter, R.; Stanton, J. R.; Fisher, D.

2009-03-24

In an effort to locate potential law enforcement-related standards that support incident management, a team from the Pacific Northwest National Laboratory (PNNL) contacted representatives from the National Institute of Standards-Office of Law Enforcement Standards (NIST-OLES), National Institute of Justice (NIJ), Federal Bureau of Investigation (FBI), Secret Service, ASTM International committees that have a law enforcement focus, and a variety of individuals from local and regional law enforcement organizations. Discussions were held with various state and local law enforcement organizations. The NIJ has published several specific equipment-related law enforcement standards that were included in the review, but it appears that law enforcement program and process-type standards are developed principally by organizations that operate at the state and local level. Input is provided from state regulations and codes and from external non-government organizations (NGOs) that provide national standards. The standards that are adopted from external organizations or developed independently by state authorities are available for use by local law enforcement agencies on a voluntary basis. The extent to which they are used depends on the respective jurisdictions involved. In some instances, use of state and local disseminated standards is mandatory, but in most cases, use is voluntary. Usually, the extent to which these standards are used appears to depend on whether or not jurisdictions receive certification from a “governing” entity due to their use and compliance with the standards. In some cases, these certification-based standards are used in principal but without certification or other compliance monitoring. In general, these standards appear to be routinely used for qualification, selection for employment, and training. In these standards, the term “Peace Officer” is frequently used to refer to law enforcement personnel. This technical review of national law

Control system architecture: The standard and non-standard models

International Nuclear Information System (INIS)

Thuot, M.E.; Dalesio, L.R.

1993-01-01

Control system architecture development has followed the advances in computer technology through mainframes to minicomputers to micros and workstations. This technology advance and increasingly challenging accelerator data acquisition and automation requirements have driven control system architecture development. In summarizing the progress of control system architecture at the last International Conference on Accelerator and Large Experimental Physics Control Systems (ICALEPCS) B. Kuiper asserted that the system architecture issue was resolved and presented a open-quotes standard modelclose quotes. The open-quotes standard modelclose quotes consists of a local area network (Ethernet or FDDI) providing communication between front end microcomputers, connected to the accelerator, and workstations, providing the operator interface and computational support. Although this model represents many present designs, there are exceptions including reflected memory and hierarchical architectures driven by requirements for widely dispersed, large channel count or tightly coupled systems. This paper describes the performance characteristics and features of the open-quotes standard modelclose quotes to determine if the requirements of open-quotes non-standardclose quotes architectures can be met. Several possible extensions to the open-quotes standard modelclose quotes are suggested including software as well as the hardware architectural features

Land-Air Interactions over Urban-Rural Transects Using Satellite Observations: Analysis over Delhi, India from 1991–2016

Directory of Open Access Journals (Sweden)

Madhavi Jain

2017-12-01

Full Text Available Over the past four decades Delhi, India, has witnessed rapid urbanization and change in land use land cover (LULC pattern, with most of the cultivable areas and wasteland being converted into built-up areas. Presently around 40% land is under built-up area, a drastic rise of 30% from 1977. The effect of changing LULC, at a local scale, on various variables-land surface temperature (LST, normalized difference vegetation index (NDVI, emissivity, albedo, evaporation, Bowen ratio, and planetary boundary layer (PBL height, from 1991–2016, is investigated. To assess the spatio-temporal dynamics of land-air interactions, we select two different 100 km transects covering the NE-SW and NW-SE expanse of Delhi and its adjoining areas. High NDVI and emissivity is found for regions with green cover and drastic reduction is noted in built-up area clusters. In both of the transects, land surface variations manifest itself in patterns of LST variation. Parametric and non-parametric correlations are able to statistically establish the land-air interactions in the city. NDVI, an indirect indicator for LULC classes, significantly helps in understanding the modifications in LST and ultimately air temperature. Significant, strong positive relationships exist between skin temperature and evaporation, skin temperature and PBL height, and PBL height and evaporation, providing insights into the meteorological changes that are associated with urbanization.

Clinical Macrosystem Simulation Translates Between Organizations.

Science.gov (United States)

Bender, G Jesse; Maryman, James A

2018-04-01

Simulation has become an integral tool in healthcare facility redesign. Immersing clinical experts into their future environment has demonstrated benefits for transition planning. This study evaluates translation of a proven macrosystems testing protocol, TESTPILOT, to an organization with limited simulation experience. An experienced TESTPILOT team guided Woman's Hospital Baton Rouge's simulation preparation for their new neonatal intensive care unit. Metrics included participant evaluations, latent safety threats (LST), and clinician surveys. Latent safety threats recorded during debriefings were addressed by workflow committees. Clinicians were surveyed at four time points for readiness and preparedness on 24 key processes. The local team invested nearly 750 hours into learning and implementing seven simulations that participants rated positively. Most of the 305 LST were minor issues. Surveys at baseline (42% of staff), postsim (18%), pretransition (26%), and postmove (29%) demonstrated strong internal consistency. System readiness lagged behind staff preparedness (P structure, team coverage, and feedback were still evolving as of move day (P organizations with limited prior exposure. Woman's Hospital Baton Rouge accrued essential skills to model and orchestrate an immersive neonatal intensive care unit and then drive effective multidisciplinary debriefings. Staff immersed in the new environment began to articulate their jobs before moving in. The trajectory of system readiness improvement corroborated LST correction. Future research is needed to determine the extent of simulation required for different organizational structures.

Determination of Optimum Viewing Angles for the Angular Normalization of Land Surface Temperature over Vegetated Surface

Directory of Open Access Journals (Sweden)

Huazhong Ren

2015-03-01

Full Text Available Multi-angular observation of land surface thermal radiation is considered to be a promising method of performing the angular normalization of land surface temperature (LST retrieved from remote sensing data. This paper focuses on an investigation of the minimum requirements of viewing angles to perform such normalizations on LST. The normally kernel-driven bi-directional reflectance distribution function (BRDF is first extended to the thermal infrared (TIR domain as TIR-BRDF model, and its uncertainty is shown to be less than 0.3 K when used to fit the hemispheric directional thermal radiation. A local optimum three-angle combination is found and verified using the TIR-BRDF model based on two patterns: the single-point pattern and the linear-array pattern. The TIR-BRDF is applied to an airborne multi-angular dataset to retrieve LST at nadir (Te-nadir from different viewing directions, and the results show that this model can obtain reliable Te-nadir from 3 to 4 directional observations with large angle intervals, thus corresponding to large temperature angular variations. The Te-nadir is generally larger than temperature of the slant direction, with a difference of approximately 0.5~2.0 K for vegetated pixels and up to several Kelvins for non-vegetated pixels. The findings of this paper will facilitate the future development of multi-angular thermal infrared sensors.

Spring Soil Temperature Anomalies over Tibetan Plateau and Summer Droughts/Floods in East Asia

Science.gov (United States)

Xue, Y.; Li, W.; LI, Q.; Diallo, I.; Chu, P. C.; Guo, W.; Fu, C.

2017-12-01

Recurrent extreme climate events, such as droughts and floods, are important features of the climate of East Asia, especially over the Yangtze River basin. Many studies have attributed these episodes to variability and anomaly of global sea surface temperatures (SST) anomaly. In addition, snow in the Tibetan Plateau has also been considered as one of the factors affecting the Asian monsoon variability. However, studies have consistently shown that SST along is unable to explain the extreme climate events fully and snow has difficulty to use as a predictor. Remote effects of observed large-scale land surface temperature (LST) and subsurface temperature variability in Tibetan Plateau (TP) on East Asian regional droughts/floods, however, have been largely ignored. We conjecture that a temporally filtered response to snow anomalies may be preserved in the LST anomaly. In this study, evidence from climate observations and model simulations addresses the LST/SUBT effects. The Maximum Covariance Analysis (MCA) of observational data identifies that a pronounce spring LST anomaly pattern over TP is closely associated with precipitation anomalies in East Asia with a dipole pattern, i.e., negative/positive TP spring LST anomaly is associated with the summer drought/flood over the region south of the Yangtze River and wet/dry conditions to the north of the Yangtze River. Climate models were used to demonstrate a causal relationship between spring cold LST anomaly in the TP and the severe 2003 drought over the southern part of the Yangtze River in eastern Asia. This severe drought resulted in 100 x 106 kg crop yield losses and an economic loss of 5.8 billion Chinese Yuan. The modeling study suggests that the LST effect produced about 58% of observed precipitation deficit; while the SST effect produced about 32% of the drought conditions. Meanwhile, the LST and SST effects also simulated the observed flood over to the north of the Yangtze River. This suggests that inclusion of

The influence of the interactions between anthropogenic activities and multiple ecological factors on land surface temperatures of urban forests

Science.gov (United States)

Ren, Y.

2017-12-01

Context Land surface temperatures (LSTs) spatio-temporal distribution pattern of urban forests are influenced by many ecological factors; the identification of interaction between these factors can improve simulations and predictions of spatial patterns of urban cold islands. This quantitative research requires an integrated method that combines multiple sources data with spatial statistical analysis. Objectives The purpose of this study was to clarify urban forest LST influence interaction between anthropogenic activities and multiple ecological factors using cluster analysis of hot and cold spots and Geogdetector model. We introduced the hypothesis that anthropogenic activity interacts with certain ecological factors, and their combination influences urban forests LST. We also assumed that spatio-temporal distributions of urban forest LST should be similar to those of ecological factors and can be represented quantitatively. Methods We used Jinjiang as a representative city in China as a case study. Population density was employed to represent anthropogenic activity. We built up a multi-source data (forest inventory, digital elevation models (DEM), population, and remote sensing imagery) on a unified urban scale to support urban forest LST influence interaction research. Through a combination of spatial statistical analysis results, multi-source spatial data, and Geogdetector model, the interaction mechanisms of urban forest LST were revealed. Results Although different ecological factors have different influences on forest LST, in two periods with different hot spots and cold spots, the patch area and dominant tree species were the main factors contributing to LST clustering in urban forests. The interaction between anthropogenic activity and multiple ecological factors increased LST in urban forest stands, linearly and nonlinearly. Strong interactions between elevation and dominant species were generally observed and were prevalent in either hot or cold spots

Local hybrid functionals: An assessment for thermochemical kinetics

International Nuclear Information System (INIS)

Kaupp, Martin; Bahmann, Hilke; Arbuznikov, Alexei V.

2007-01-01

Local hybrid functionals with position-dependent exact-exchange admixture are a new class of exchange-correlation functionals in density functional theory that promise to advance the available accuracy in many areas of application. Local hybrids with different local mixing functions (LMFs) governing the position dependence are validated for the heats of formation of the extended G3/99 set, and for two sets of barriers of hydrogen-transfer and heavy-atom transfer reactions (HTBH38 and NHTBH38 databases). A simple local hybrid Lh-SVWN with only Slater and exact exchange plus local correlation and a one-parameter LMF, g(r)=b(τ W (r)/τ(r)), performs best and provides overall mean absolute errors for thermochemistry and kinetics that are a significant improvement over standard state-of-the-art global hybrid functionals. In particular, this local hybrid functional does not suffer from the systematic deterioration that standard functionals exhibit for larger molecules. In contrast, local hybrids based on generalized gradient approximation exchange tend to give rise to nonintuitive LMFs, and no improved functionals have been obtained along this route. The LMF is a real-space function and thus can be analyzed in detail. We use, in particular, graphical analyses to rationalize the performance of different local hybrids for thermochemistry and reaction barriers

Accelerating the Adoption of Second-Tier Reach Standards forApplicable Appliance Products in China

Energy Technology Data Exchange (ETDEWEB)

Lin, Jiang; Fridley, David

2007-03-01

The minimum energy efficiency standards program for household appliances in China was initiated in 1989. Since 1996, CLASP and its implementing partner, LBNL, have assisted China in developing 11 minimum energy performance standards (MEPS) for 9 products and endorsement labels for 11 products including: refrigerators; air conditioners; clothes washers; televisions; printers; computers; monitors; fax machines; copiers; DVD/VCD players; external power supplies; and set-top boxes (under development). Before 2003, China's traditional approach to standards development involved small increases in efficiency requirements for implementation within 6 months of a standard's approval. Since 2003, China has adopted a new approach in setting MEPS. This new approach involves the development of two tiers of standards--one for initial implementation and a second tier at a more aggressive level of energy efficiency for implementation three to five years later. The second-tier standard is also referred to as a 'reach standard'. Reach standards have now been developed in China for: color TVs; refrigerators; air conditioners; and external power supplies. This report is presented in five sections. After the introduction in Section 1, Section 2 analyzes the distribution of the efficiency of refrigerators and air-conditioners in China based on data collected by the China Energy Label Center for the mandatory energy information label program. The results provide an assessment of the adoption of reach standards for these two products. Section 3 summarizes on-going collaborations with Shanghai related to early local adoption of reach standards, and presents both the impact and an analysis of barriers to the local adoption of reach standard for air-conditioners. Section 4 offers suggestions for local governments on how to move forward in adopting reach standards in their localities and concludes with a summary of the results and a plan for developing local capacity in

A scientific operations plan for the large space telescope. [ground support system design

Science.gov (United States)

West, D. K.

1977-01-01

The paper describes an LST ground system which is compatible with the operational requirements of the LST. The goal of the approach is to minimize the cost of post launch operations without seriously compromising the quality and total throughput of LST science. Attention is given to cost constraints and guidelines, the telemetry operations processing systems (TELOPS), the image processing facility, ground system planning and data flow, and scientific interfaces.

Optimal use of land surface temperature data to detect changes in tropical forest cover

Science.gov (United States)

Van Leeuwen, T. T.; Frank, A. J.; Jin, Y.; Smyth, P.; Goulden, M.; van der Werf, G.; Randerson, J. T.

2011-12-01

Rapid and accurate assessment of global forest cover change is needed to focus conservation efforts and to better understand how deforestation is contributing to the build up of atmospheric CO2. Here we examined different ways to use remotely sensed land surface temperature (LST) to detect changes in tropical forest cover. In our analysis we used monthly 0.05×0.05 degree Terra MODerate Resolution Imaging Spectroradiometer (MODIS) observations of LST and PRODES (Program for the Estimation of Deforestation in the Brazilian Amazon) estimates of forest cover change. We also compared MODIS LST observations with an independent estimate of forest cover loss derived from MODIS and Landsat observations. Our study domain of approximately 10×10 degree included most of the Brazilian state of Mato Grosso. For optimal use of LST data to detect changes in tropical forest cover in our study area, we found that using data sampled during the end of the dry season (~1-2 months after minimum monthly precipitation) had the greatest predictive skill. During this part of the year, precipitation was low, surface humidity was at a minimum, and the difference between day and night LST was the largest. We used this information to develop a simple temporal sampling algorithm appropriate for use in pan-tropical deforestation classifiers. Combined with the normalized difference vegetation index (NDVI), a logistic regression model using day-night LST did moderately well at predicting forest cover change. Annual changes in day-night LST difference decreased during 2006-2009 relative to 2001-2005 in many regions within the Amazon, providing independent confirmation of lower deforestation levels during the latter part of this decade as reported by PRODES. The use of day-night LST differences may be particularly valuable for use with satellites that do not have spectral bands that allow for the estimation of NDVI or other vegetation indices.

Comparing and Combining Remotely Sensed Land Surface Temperature Products for Improved Hydrological Applications

Directory of Open Access Journals (Sweden)

Robert M. Parinussa

2016-02-01

Full Text Available Land surface temperature (LST is an important variable that provides a valuable connection between the energy and water budget and is strongly linked to land surface hydrology. Space-borne remote sensing provides a consistent means for regularly observing LST using thermal infrared (TIR and passive microwave observations each with unique strengths and weaknesses. The spatial resolution of TIR based LST observations is around 1 km, a major advantage when compared to passive microwave observations (around 10 km. However, a major advantage of passive microwaves is their cloud penetrating capability making them all-weather sensors whereas TIR observations are routinely masked under the presence of clouds and aerosols. In this study, a relatively simple combination approach that benefits from the cloud penetrating capacity of passive microwave sensors was proposed. In the first step, TIR and passive microwave LST products were compared over Australia for both anomalies and raw timeseries. A very high agreement was shown over the vast majority of the country with R2 typically ranging from 0.50 to 0.75 for the anomalies and from 0.80 to 1.00 for the raw timeseries. Then, the scalability of the passive microwave based LST product was examined and a pixel based merging approach through linear scaling was proposed. The individual and merged LST products were further compared against independent LST from the re-analysis model outputs. This comparison revealed that the TIR based LST product agrees best with the re-analysis data (R2 0.26 for anomalies and R2 0.76 for raw data, followed by the passive microwave LST product (R2 0.16 for anomalies and R2 0.66 for raw data and the combined LST product (R2 0.18 for anomalies and R2 0.62 for raw data. It should be noted that the drop in performance comes with an increased revisit frequency of approximately 20% compared to the revised frequency of the TIR alone. Additionally, this comparison against re

Microwave implementation of two-source energy balance approach for estimating evapotranspiration

Directory of Open Access Journals (Sweden)

T. R. H. Holmes

2018-02-01

Full Text Available A newly developed microwave (MW land surface temperature (LST product is used to substitute thermal infrared (TIR-based LST in the Atmosphere–Land Exchange Inverse (ALEXI modeling framework for estimating evapotranspiration (ET from space. ALEXI implements a two-source energy balance (TSEB land surface scheme in a time-differential approach, designed to minimize sensitivity to absolute biases in input records of LST through the analysis of the rate of temperature change in the morning. Thermal infrared retrievals of the diurnal LST curve, traditionally from geostationary platforms, are hindered by cloud cover, reducing model coverage on any given day. This study tests the utility of diurnal temperature information retrieved from a constellation of satellites with microwave radiometers that together provide six to eight observations of Ka-band brightness temperature per location per day. This represents the first ever attempt at a global implementation of ALEXI with MW-based LST and is intended as the first step towards providing all-weather capability to the ALEXI framework. The analysis is based on 9-year-long, global records of ALEXI ET generated using both MW- and TIR-based diurnal LST information as input. In this study, the MW-LST (MW-based LST sampling is restricted to the same clear-sky days as in the IR-based implementation to be able to analyze the impact of changing the LST dataset separately from the impact of sampling all-sky conditions. The results show that long-term bulk ET estimates from both LST sources agree well, with a spatial correlation of 92 % for total ET in the Europe–Africa domain and agreement in seasonal (3-month totals of 83–97 % depending on the time of year. Most importantly, the ALEXI-MW (MW-based ALEXI also matches ALEXI-IR (IR-based ALEXI very closely in terms of 3-month inter-annual anomalies, demonstrating its ability to capture the development and extent of drought conditions. Weekly ET output

Local recurrence risk after previous salvage mastectomy.

Science.gov (United States)

Tanabe, M; Iwase, T; Okumura, Y; Yoshida, A; Masuda, N; Nakatsukasa, K; Shien, T; Tanaka, S; Komoike, Y; Taguchi, T; Arima, N; Nishimura, R; Inaji, H; Ishitobi, M

2016-07-01

Breast-conserving surgery is a standard treatment for early breast cancer. For ipsilateral breast tumor recurrence (IBTR) after breast-conserving surgery, salvage mastectomy is the current standard surgical procedure. However, it is not rare for patients with IBTR who have received salvage mastectomy to develop local recurrence. In this study, we examined the risk factors of local recurrence after salvage mastectomy for IBTR. A total of 118 consecutive patients who had histologically confirmed IBTR without distant metastases and underwent salvage mastectomy without irradiation for IBTR between 1989 and 2008 were included from eight institutions in Japan. The risk factors of local recurrence were assessed. The median follow-up period from salvage mastectomy for IBTR was 4.6 years. Patients with pN2 or higher on diagnosis of the primary tumor showed significantly poorer local recurrence-free survival than those with pN0 or pN1 at primary tumor (p mastectomy for IBTR. Further research and validation studies are needed. (UMIN-CTR number UMIN000008136). Copyright © 2016 Elsevier Ltd. All rights reserved.

Preparation, characterization and efficacy of lysostaphin-chitosan gel against Staphylococcus aureus.

Science.gov (United States)

Nithya, Sai; Nimal, T R; Baranwal, Gaurav; Suresh, Maneesha K; C P, Anju; Anil Kumar, V; Gopi Mohan, C; Jayakumar, R; Biswas, Raja

2018-04-15

Lysostaphin (LST) is a bacteriocin that cleaves within the pentaglycine cross bridge of Staphylococcus aureus peptidoglycan. Previous studies have reported the high efficiency of LST even against multi drug resistant S. aureus including methicillin resistant S. aureus (MRSA). In this study, we have developed a new chitosan based hydrogel formulation of LST to exploit its anti-staphylococcal activity. The atomic interactions of LST with chitosan were studied by molecular docking studies. The rheology and the antibacterial properties of the developed LSTC gel were evaluated. The developed LST containing chitosan hydrogel (LSTC gel) was flexible, flows smoothly and remains stable at physiological temperature. The in vitro studies by agar well diffusion and ex vivo studies in porcine skin model exhibited a reduction in S. aureus survival by ∼3 Log 10 CFU/mL in the presence of LSTC gel. The cytocompatibility of the gel was tested in vitro using macrophage RAW 264.7 cell line and in vivo in Drosophila melanogaster. A gradual disruption of S. aureus biofilms with the increase of LST concentrations in the LSTC gel was observed which was confirmed by SEM analysis. We conclude that LSTC gel could be highly effectual and advantageous over antibiotics in treating staphylococcal-topical and biofilm infections. Copyright © 2018 Elsevier B.V. All rights reserved.

Neurological disease in wild loggerhead sea turtles Caretta caretta.

Science.gov (United States)

Jacobson, Elliott R; Homer, Bruce L; Stacy, Brian A; Greiner, Ellis C; Szabo, Nancy J; Chrisman, Cheryl L; Origgi, Francesco; Coberley, Sadie; Foley, Allen M; Landsberg, Jan H; Flewelling, Leanne; Ewing, Ruth Y; Moretti, Richie; Schaf, Susan; Rose, Corinne; Mader, Douglas R; Harman, Glenn R; Manire, Charles A; Mettee, Nancy S; Mizisin, Andrew P; Shelton, G Diane

2006-06-12

Beginning in October 2000, subadult loggerhead sea turtles Caretta caretta showing clinical signs of a neurological disorder were found in waters off south Florida, USA. Histopathology indicated generalized and neurologic spirorchiidiasis. In loggerhead sea turtles (LST) with neurospirorchiidiasis, adult trematodes were found in the meninges of the brain and spinal cord of 7 and 3 affected turtles respectively, and multiple encephalic intravascular or perivascular eggs were associated with granulomatous or mixed leukocytic inflammation, vasculitis, edema, axonal degeneration and occasional necrosis. Adult spirorchiids were dissected from meningeal vessels of 2 of 11 LST brains and 1 of 10 spinal cords and were identified as Neospirorchis sp. Affected LST were evaluated for brevetoxins, ciguatoxins, saxitoxins, domoic acid and palytoxin. While tissues from 7 of 20 LST tested positive for brevetoxins, the levels were not considered to be in a range causing acute toxicosis. No known natural (algal blooms) or anthropogenic (pollutant spills) stressors co-occurred with the turtle mortality. While heavy metal toxicosis and organophosphate toxicosis were also investigated as possible causes, there was no evidence for their involvement. We speculate that the clinical signs and pathologic changes seen in the affected LST resulted from combined heavy spirorchiid parasitism and possible chronic exposure to a novel toxin present in the diet of LST.

The Effect of IFRS Adoption on the Financial Reports of Local Government Entities

Directory of Open Access Journals (Sweden)

Kamran Ahmed

2012-09-01

Full Text Available This paper aims to analyse the changes in accounting surplus (loss, equity and assets, and liabilities as a result of accounting policy changes from the Australian Accounting Standards (AAS to the International Financial Reporting Standards (IFRS in Australian local government entities. Using the reconciliation notes disclosed by 117 local government entities, evidence is provided on the effects of IFRS adoption by identifying the key items that of difference between IFRS and AASB. The results show some differences between two sets of accounts prepared under these different accounting standards. While the average surplus (loss of local councils has decreased, their equities, assets and liabilities have increased, with no major significant changes in their overall financial position, except for liabilities. These results indicate the possible consequences of the adoption of IFRS by local government entities in other countries on performance indicators who have or are yet to implement these standards.

JJ1017 committee report: image examination order codes--standardized codes for imaging modality, region, and direction with local expansion: an extension of DICOM.

Science.gov (United States)

Kimura, Michio; Kuranishi, Makoto; Sukenobu, Yoshiharu; Watanabe, Hiroki; Tani, Shigeki; Sakusabe, Takaya; Nakajima, Takashi; Morimura, Shinya; Kabata, Shun

2002-06-01

The digital imaging and communications in medicine (DICOM) standard includes parts regarding nonimage data information, such as image study ordering data and performed procedure data, and is used for sharing information between HIS/RIS and modality systems, which is essential for IHE. To bring such parts of the DICOM standard into force in Japan, a joint committee of JIRA and JAHIS established the JJ1017 management guideline, specifying, for example, which items are legally required in Japan, while remaining optional in the DICOM standard. In Japan, the contents of orders from referring physicians for radiographic examinations include details of the examination. Such details are not used typically by referring physicians requesting radiographic examinations in the United States, because radiologists in the United States often determine the examination protocol. The DICOM standard has code tables for examination type, region, and direction for image examination orders. However, this investigation found that it does not include items that are detailed sufficiently for use in Japan, because of the above-mentioned reason. To overcome these drawbacks, we have generated the JJ1017 code for these 3 codes for use based on the JJ1017 guidelines. This report introduces the JJ1017 code. These codes (the study type codes in particular) must be expandable to keep up with technical advances in equipment. Expansion has 2 directions: width for covering more categories and depth for specifying the information in more detail (finer categories). The JJ1017 code takes these requirements into consideration and clearly distinguishes between the stem part as the common term and the expansion. The stem part of the JJ1017 code partially utilizes the DICOM codes to remain in line with the DICOM standard. This work is an example of how local requirements can be met by using the DICOM standard and extending it.

New phases of thermal SYM and LST from Kaluza-Klein black holes

DEFF Research Database (Denmark)

Harmark, Troels; Obers, Niels A.

2005-01-01

between phases of Kaluza-Klein black holes and the thermodynamic behavior of the non-gravitational theories dual to near-extremal branes on a circle. In particular, for the thermodynamics of strongly-coupled supersymmetric Yang-Mills theories on a circle we predict the existence of a new non-uniform phase......We review the recently found map that takes any static and neutral Kaluza-Klein black hole, i.e. any static and neutral black hole on Minkowski-space times a circle Md × S1, and maps it to a corresponding solution for a non- and near-extremal brane on a circle. This gives a precise connection...... and find new information about the localized phase. We also find evidence for the existence of a new stable phase of (2, 0) Little String Theory in the canonical ensemble for temperatures above its Hagedorn temperature....

Internationalization and Localization in Python

CERN Multimedia

CERN. Geneva

2016-01-01

Internationalization and Localization are increasingly important in an interconnected world. Regardless of that, developers tend to treat them as secondary issues, very often choosing to address them properly when it's already too late. The fact that most programming language standard libraries choose to ignore the matter doesn't help either. In this talk we will present some useful Python libraries and tools that can help you internationalize and localize your code with minimal effort. We will also describe some common pitfalls and problems.

Creating a seamless 1 km resolution daily land surface temperature dataset for urban and surrounding areas in the conterminous United States

Energy Technology Data Exchange (ETDEWEB)

Li, Xiaoma; Zhou, Yuyu; Asrar, Ghassem R.; Zhu, Zhengyuan

2018-03-01

High spatiotemporal land surface temperature (LST) datasets are increasingly needed in a variety of fields such as ecology, hydrology, meteorology, epidemiology, and energy systems. Moderate Resolution Imaging Spectroradiometer (MODIS) LST is one of such high spatiotemporal datasets that are widely used. But, it has large amount of missing values primarily because of clouds. Gapfilling the missing values is an important approach to create high spatiotemporal LST datasets. However current gapfilling methods have limitations in terms of accuracy and time required to assemble the data over large areas (e.g., national and continental levels). In this study, we developed a 3-step hybrid method by integrating a combination of daily merging, spatiotemporal gapfilling, and temporal interpolation methods, to create a high spatiotemporal LST dataset using the four daily LST observations from the two MODIS instruments on Terra and Aqua satellites. We applied this method in urban and surrounding areas for the conterminous U.S. in 2010. The evaluation of the gapfilled LST product indicates that its root mean squared error (RMSE) to be 3.3K for mid-daytime (1:30 pm) and 2.7K for mid-13 nighttime (1:30 am) observations. The method can be easily extended to other years and regions and is also applicable to other satellite products. This seamless daily (mid-daytime and mid-nighttime) LST product with 1 km spatial resolution is of great value for studying effects of urbanization (e.g., urban heat island) and the related impacts on people, ecosystems, energy systems and other infrastructure for cities.

Spatio-temporal Assessment of Land Use/ Land Cover Dynamics and Urban Heat Island of Jaipur City using Satellite Data

Science.gov (United States)

Jalan, S.; Sharma, K.

2014-11-01

Urban Heat Island (UHI) refers to the phenomena of higher surface temperature occurring in urban areas as compared to the surrounding countryside attributable to urbanization. Spatio-temporal changes in UHI can be quantified through Land Surface Temperature (LST) derived from satellite imageries. Spatial variations in LST occur due to complexity of land surface - combination of impervious surface materials, vegetation, exposed soils as well as water surfaces. Jaipur city has observed rapid urbanization over the last decade. Due to rising population pressure the city has expanded considerably in areal extent and has also observed substantial land use/land cover (LULC) changes. The paper aims to determine changes in the LST and UHI phenomena for Jaipur city over the period from 2000 to 2011 and analyzes the spatial distribution and temporal variation of LST in context of changes in LULC. Landsat 7 ETM+ (2000) and Landsat 5 TM (2011) images of summer season have been used. Results reveal that Jaipur city has witnessed considerable growth in built up area at the cost of greener patches over the last decade, which has had clear impact on variation in LST. There has been an average rise of 2.99 °C in overall summer temperature. New suburbs of the city record 2° to 4 °C increase in LST. LST change is inversely related to change in vegetation cover and positively related to extent of built up area. The study concludes that UHI of Jaipur city has intensified and extended over new areas.

Land surface temperature as potential indicator of burn severity in forest Mediterranean ecosystems

Science.gov (United States)

Quintano, C.; Fernández-Manso, A.; Calvo, L.; Marcos, E.; Valbuena, L.

2015-04-01

Forest fires are one of the most important causes of environmental alteration in Mediterranean countries. Discrimination of different degrees of burn severity is critical for improving management of fire-affected areas. This paper aims to evaluate the usefulness of land surface temperature (LST) as potential indicator of burn severity. We used a large convention-dominated wildfire, which occurred on 19-21 September, 2012 in Northwestern Spain. From this area, a 1-year series of six LST images were generated from Landsat 7 Enhanced Thematic Mapper (ETM+) data using a single channel algorithm. Further, the Composite Burn Index (CBI) was measured in 111 field plots to identify the burn severity level (low, moderate, and high). Evaluation of the potential relationship between post-fire LST and ground measured CBI was performed by both correlation analysis and regression models. Correlation coefficients were higher in the immediate post-fire LST images, but decreased during the fall of 2012 and increased again with a second maximum value in summer, 2013. A linear regression model between post-fire LST and CBI allowed us to represent spatially predicted CBI (R-squaredadj > 85%). After performing an analysis of variance (ANOVA) between post-fire LST and CBI, a Fisher's least significant difference test determined that two burn severity levels (low-moderate and high) could be statistically distinguished. The identification of such burn severity levels is sufficient and useful to forest managers. We conclude that summer post-fire LST from moderate resolution satellite data may be considered as a valuable indicator of burn severity for large fires in Mediterranean forest ecosytems.

Validation of the assert subchannel code: Prediction of CHF in standard and non-standard Candu bundle geometries

International Nuclear Information System (INIS)

Carver, M.B.; Kiteley, J.C.; Zhou, R.Q.N.; Junop, S.V.; Rowe, D.S.

1993-01-01

The ASSERT code has been developed to address the three-dimensional computation of flow and phase distribution and fuel element surface temperatures within the horizontal subchannels of CANDU PHWR fuel channels, and to provide a detailed prediction of critical heat flux (CHF) distribution throughout the bundle. The ASSERT subchannel code has been validated extensively against a wide repertoire of experiments; its combination of three-dimensional prediction of local flow conditions with a comprehensive method of prediting CHF at these local conditions, makes it a unique tool for predicting CHF for situations outside the existing experimental data base. In particular, ASSERT is an appropriate tool to systematically investigate CHF under conditions of local geometric variations, such as pressure tube creep and fuel element strain. This paper discusses the numerical methodology used in ASSERT, the constitutive relationships incorporated, and the CHF assessment methodology. The evolutionary validation plan is discussed, and early validation exercises are summarized. The paper concentrates, however, on more recent validation exercises in standard and non-standard geometries

Standards development for the nuclear industry

International Nuclear Information System (INIS)

Domondon, D.B.

The ushering of nuclear era in the Philippines with the construction of the PNPP-I (Philippine Nuclear Power Plant) necessitates the evolvement and use of nuclear standards as a tool for safety evaluation in the licensing process. The Department of Nuclear Regulation and Safeguards under the Philippine Atomic Energy Commission has as one of its responsibilities the establishment of regulatory standards to ensure safe operation of nuclear facilities. This article points out the needs for nuclear standards and the steps in standard development which involve an enormous amount of resources in terms of manpower, expertise and money. The staff of the Department of Nuclear Regulations and Safeguards (DNRS) does not intend to engage in the original development of standards; rather, it reviews standards in use elsewhere, specifically in the U.S. and adopts to local conditions. (author)

MODIS Land Surface Temperature time series reconstruction with Open Source GIS: A new quality of temperature based ecological indicators in complex terrain (Invited)

Science.gov (United States)

Neteler, M.

2009-12-01

In complex terrain like the Central European Alps, meteorological stations and ground surveys are usually sparsely and/or irregularly distributed and often favor agricultural areas. The application of traditional geospatial interpolation methods in complex terrain remains challenging and difficult to optimize. An alternative data source is remote sensing: high temporal resolution satellite data are continuously gaining interest since these data are intrinsically spatialized: continuous field of observations is obtained with this tool instead of point data. The increasing data availability suggests using these time series as surrogate to certain measures from meteorological stations, especially for temperature and related derivatives. The Terra and Aqua satellites with the Moderate Resolution Imaging Spectroradiometer (MODIS) provide four Earth coverages per day at various resolutions. We analyzed 8 years (2000 to 2008) of daily land surface temperature (LST) data from MODIS in an area located in the Southern European Alps. A method was developed to reconstruct incomplete maps (cloud coverage, invalid pixels) based on image statistics and on a model that includes additional GIS layers. The original LST map resolution of 1000m could be improved to 200m in this process which renders the resulting LST maps applicable at regional scales. We propose the use of these reconstructed daily LST time series as surrogate to meteorological observations especially in the area of epidemiological modeling where data are typically aggregated to decadal indicators. From these daily LST map series, derivable indicators include: 1) temperatures minima, means and maxima for annual/monthly/decadal periods; 2) unusual hot summers;3) the calculation of growing degree days, and 4) spring temperature increase or autumnal temperature decrease. Since more than 8 years of MODIS LST data are available today, even preliminary gradients can be extracted to assess multi-annual temperature trends

Localization strategy for magnetic resonance coronary angiography

International Nuclear Information System (INIS)

Cheng Liuquan; Gao Yuangui; Sun Wei; Sheng Fugeng; Cai Youquan

2003-01-01

Objective: To develop a localization strategy for magnetic resonance coronary angiography (MRCA). Methods: In 89 subjects, the standard 4-chamber view and long-axis view of left and right ventricle were acquired using Fast-Imaging-Employing-Steady-State-Acquisition (FIESTA) sequence in CINE mode, and the trigger-delay time for mid-diastolic phase was determined. Coronary vessels including right coronary artery (RCA), left main (LM), left anterior descending (LAD), and left circumflex (LCX) were localized and imaged using 3- dimensional fat-suppressed FIESTA sequence during end-expiration. The reproducibility of the localization strategy was evaluated by taking the standard of coronary segmentation system recommended by American Heart Association. Results: Eighty-six subjects completed the examination with full respiratory co-operation and the indication ratio was 96.63%. Nine planes were optimized as the standard to target the main branches of coronary arteries, and a comprehensive reproducibility reached 100% in demonstrating the proximal and middle segment of RCA (AHA-18, 19), LM (AHA-1, 2), proximal and middle segment of LAD (AHA-3, 5, 7), and proximal LCX (AHA-10). The reproducibility for the demonstration of distal segments of LAD, LCX, and RCA (AHA-9, 14, 21) was 94.19%, 72.09%, and 96.51%, respectively. Conclusion: This is a simple and practical localization strategy for MRCA. It could image the proximal and middle segments of the coronary arteries with good reproducibility, which indicates the potential for clinical application

Changes in Local Public Health System Performance Before and After Attainment of National Accreditation Standards.

Science.gov (United States)

Ingram, Richard C; Mays, Glen P; Kussainov, Nurlan

The aim of this study is to investigate the impact of Public Health Accreditation Board (PHAB) accreditation on the delivery of public health services and on participation from other sectors in the delivery of public health services in local public health systems. This study uses a longitudinal repeated measures design to identify differences between a cohort of public health systems containing PHAB-accredited local health departments and a cohort of public health systems containing unaccredited local health departments. It uses data spanning from 2006 to 2016. This study examines a cohort of local public health systems that serves large populations and contains unaccredited and PHAB-accredited local health departments. Data in this study were collected from the directors of health departments that include local public health systems followed in the National Longitudinal Study of Public Health Systems. The intervention examined is PHAB accreditation. The study focuses on 4 areas: the delivery of core public health services, local health department contribution toward these services, participation in the delivery of these services by other members of the public health system, and public health system makeup. Prior to the advent of accreditation, public health systems containing local health departments that were later accredited by PHAB appear quite similar to their unaccredited peers. Substantial differences between the 2 cohorts appear to manifest themselves after the advent of accreditation. Specifically, the accredited cohort seems to offer a broader array of public health services, involve more partners in the delivery of those services, and enjoy a higher percentage of comprehensive public health systems. The results of this study suggest that accreditation may yield significant benefits and may help public health systems develop the public health system capital necessary to protect and promote the public's health.

Analysing Regional Land Surface Temperature Changes by Satellite Data, a Case Study of Zonguldak, Turkey

Science.gov (United States)

Sekertekin, A.; Kutoglu, S.; Kaya, S.; Marangoz, A. M.

2014-12-01

In recent years, climate change is one of the most important problems that the ecological system of the world has been encountering. Global warming and climate change have been studied frequently by all disciplines all over the world and Geomatics Engineering also contributes to such studies by means of remote sensing, global positioning system etc. Monitoring Land Surface Temperature (LST) via remote sensing satellites is one of the most important contributions to climatology. LST is an important parameter governing the energy balance on the Earth and there are lots of algorithms to obtain LST by remote sensing techniques. The most commonly used algorithms are split-window algorithm, temperature/emissivity separation method, mono-window algorithm and single channel method. Generally three algorithms are used to obtain LST by using Landsat 5 TM data. These algorithms are radiative transfer equation method, single channel method and mono-window algorithm. Radiative transfer equation method is not applicable because during the satellite pass, atmospheric parameters must be measured in-situ. In this research, mono window algorithm was implemented to Landsat 5 TM image. Besides, meteorological data such as humidity and temperature are used in the algorithm. Acquisition date of the image is 28.08.2011 and our study area is Zonguldak, Turkey. High resolution images are used to investigate the relationships between LST and land cover type. As a result of these analyses, area with vegetation cover has approximately 5 ºC lower temperature than the city center and arid land. Because different surface properties like reinforced concrete construction, green zones and sandbank are all together in city center, LST differs about 10 ºC in the city center. The temperature around some places in thermal power plant region Çatalağzı, is about 5 ºC higher than city center. Sandbank and agricultural areas have highest temperature because of land cover structure. Thanks to this

The life histories of endangered hammerhead sharks (Carcharhiniformes, Sphyrnidae) from the east coast of Australia.

Science.gov (United States)

Harry, A V; Macbeth, W G; Gutteridge, A N; Simpfendorfer, C A

2011-06-01

The life histories of two globally endangered hammerhead sharks, Sphyrna lewini and Sphyrna mokarran, were examined using samples collected from a range of commercial fisheries operating along the east coast of Australia. The catch of S. lewini was heavily biased towards males, and there were significant differences in von Bertalanffy growth parameters (L(∞) and k) and maturity [stretched total length (L(ST)) and age (A) at which 50% are mature, L(ST50) and A(50)] between those caught in the tropics (L(∞) = 2119 mm, k = 0·163, L(ST50) = 1471 mm, A(50) = 5·7 years) and those caught in temperate waters (L(∞) = 3199 mm, k = 0·093, L(ST50) = 2043 mm, A(50) = 8·9 years). The best-fit estimates for a three-parameter von Bertalanffy growth curve fit to both sexes were L(∞) = 3312 mm, L(0) = 584 mm and k = 0·076. Males attained a maximum age of 21 years and grew to at least 2898 mm L(ST). The longevity, maximum length and maturity of females could not be estimated as mature animals could not be sourced from any fishery. Length at birth inferred from neonates with open umbilical scars was 465-563 mm L(ST). There was no significant difference in length and age at maturity of male and female S. mokarran, which reached 50% maturity at 2279 mm L(ST) and 8·3 years. Sphyrna mokarran grew at a similar rate to S. lewini and the best-fit estimates for a two-parameter von Bertalanffy equation fit to length-at-age data for sexes combined with an assumed mean length-at-birth of 700 mm were L(∞) = 4027 mm and k = 0·079. Females attained a maximum age of 39·1 years and grew to at least 4391 mm L(ST). The oldest male S. mokarran was 31·7 years old and 3691 mm L(ST). Validation of annual growth-band deposition in S. mokarran was achieved through a mark, tag and recapture study. © 2011 The Authors. Journal of Fish Biology © 2011 The Fisheries Society of the British Isles.

Review of Welding Terminology

Directory of Open Access Journals (Sweden)

Angelika Petrėtienė

2011-04-01

Full Text Available The paper discusses welding terms in accordance with the Lithuanian standard LST EN 1792 „Welding. The multilingual list of welding terms and similar processes”, „The Russian–Lithuanian dictionary of the terms of mechanical engineering technology and welding“ and the examples from postgraduates‘ final works. It analyses the infringement of lexical, word-building and morphological rules. First-year students should already be familiar with the standardized terms of their speciality. More active propagation of the terms should help to avoid terminology mistakes in various scientific spheres.

Comparison of local metronidazole and a local antiseptic in the treatment of bacterial vaginosis.

Science.gov (United States)

Novakov Mikic, Aleksandra; Budakov, Dragan

2010-07-01

Bacterial vaginosis (BV) is characterized by a mixed flora of pathogenic anaerobic bacteria and associated with risks of pathologic conditions. In the present study, therapy with a local antiseptic spray (octenidine hydrochloride/phenoxyethanol, OHP) for 7 or 14 days is compared against the standard local therapy of BV (metronidazole) in a Serbian patient population. As much as 450 women were treated in groups with either 7 days metronidazole vaginal tablets, 7 days OHP, or 14 days OHP. Control smears were taken after each treatment period. In total, 63.2% of the women were without indications of BV after therapy (metronidazole: 61.0%, OHP 7 days: 57.6%, and OHP 14 days: 71.0%). Significantly fewer women were affected from infections after treatment with 14 days OHP compared to OHP for 7 days. Octenidine hydrochloride/phenoxyethanol spray was as effective as the standard therapy with metronidazole. Patients stated that OHP was more comfortable, easier to apply, and side effects were lesser.

75 FR 76397 - Effectiveness of Federal Agency Participation in Standardization in Select Technology Sectors for...

Science.gov (United States)

2010-12-08

.... Cyber Security. 4. Emergency Communications Interoperability. 5. Radioactivity Detectors and Radiation... development. State and local governments, standards-setting organizations, industry, consumers, manufacturers... agencies work with standards-setting organizations, industry, State and local governments, and consumers to...

Mobile localization in nonlinear Schroedinger lattices

International Nuclear Information System (INIS)

Gomez-Gardenes, J.; Falo, F.; Floria, L.M.

2004-01-01

Using continuation methods from the integrable Ablowitz-Ladik lattice, we have studied the structure of numerically exact mobile discrete breathers in the standard discrete nonlinear Schroedinger equation. We show that, away from that integrable limit, the mobile pulse is dressed by a background of resonant plane waves with wavevectors given by a certain selection rule. This background is seen to be essential for supporting mobile localization in the absence of integrability. We show how the variations of the localized pulse energy during its motion are balanced by the interaction with this background, allowing the localization mobility along the lattice

Noncommuting observables and local realism

International Nuclear Information System (INIS)

Malley, James D.; Fine, Arthur

2005-01-01

A standard approach in the foundations of quantum mechanics studies local realism and hidden variables models exclusively in terms of violations of Bell-like inequalities. Thus quantum nonlocality is tied to the celebrated no-go theorems, and these comprise a long list that includes the Kochen-Specker and Bell theorems, as well as elegant refinements by Mermin, Peres, Hardy, GHZ, and many others. Typically entanglement or carefully prepared multipartite systems have been considered essential for violations of local realism and for understanding quantum nonlocality. Here we show, to the contrary, that sharp violations of local realism arise almost everywhere without entanglement. The pivotal fact driving these violations is just the noncommutativity of quantum observables. We demonstrate how violations of local realism occur for arbitrary noncommuting projectors, and for arbitrary quantum pure states. Finally, we point to elementary tests for local realism, using single particles and without reference to entanglement, thus avoiding experimental loopholes and efficiency issues that continue to bedevil the Bell inequality related tests

45 CFR 2541.200 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 4 2010-10-01 2010-10-01 false Standards for financial management systems. 2541... STATE AND LOCAL GOVERNMENTS Post-Award Requirements § 2541.200 Standards for financial management... violation of the restrictions and prohibitions of applicable statutes. (b) The financial management systems...

Imposed Thermal Fatigue and Post-Thermal-Cycle Wear Resistance of Biomimetic Gray Cast Iron by Laser Treatment

Science.gov (United States)

Sui, Qi; Zhou, Hong; Zhang, Deping; Chen, Zhikai; Zhang, Peng

2017-08-01

The present study aims to create coupling biomimetic units on gray cast iron substrate by laser surface treatment (LST). LSTs for single-step (LST1) and two-step (LST2) processes, were carried out on gray cast iron in different media (air and water). Their effects on microstructure, thermal fatigue, and post-thermal-cycle wear (PTW) resistance on the specimens were studied. The tests were carried out to examine the influence of crack-resistance behavior as well as the biomimetic surface on its post-thermal-cycle wear behavior and different units, with different laser treatments for comparison. Results showed that LST2 enhanced the PTW behaviors of gray cast iron, which then led to an increase in its crack resistance. Among the treated cast irons, the one treated by LST2 in air showed the lowest residual stress, due to the positive effect of the lower steepness of the thermal gradient. Moreover, the same specimen showed the best PTW performance, due to its superior crack resistance and higher hardness as a result of it.

Automating data analysis during the inspection of boiler tubes using line scanning thermography

Science.gov (United States)

Ley, Obdulia; Momeni, Sepand; Ostroff, Jason; Godinez, Valery

2012-05-01

Failures in boiler waterwalls can occur when a relatively small amount of corrosion and loss of metal have been experienced. This study presents our efforts towards the application of Line Scanning Thermography (LST) for the analysis of thinning in boiler waterwall tubing. LST utilizes a line heat source to thermally excite the surface to be inspected and an infrared detector to record the transient surface temperature increase observed due to the presence of voids, thinning or other defects. In waterwall boiler tubes the defects that can be detected using LST correspond to corrosion pitting, hydrogen damage and wall thinning produced by inadequate burner heating or problems with the water chemistry. In this paper we discuss how the LST technique is implemented to determine thickness from the surface temperature data, and we describe our efforts towards developing a semiautomatic analysis tool to speed up the time between scanning, reporting and implementing repairs. We compare the density of data produced by the common techniques used to assess wall thickness and the data produced by LST.

Impact of Urban Climate Landscape Patterns on Land Surface Temperature in Wuhan, China

Directory of Open Access Journals (Sweden)

Yasha Wang

2017-09-01

Full Text Available Facing urban warming, mitigation and adaptation strategies are not efficient enough to tackle excessive urban heat, especially at the local scale. The local climate zone (LCZ classification scheme is employed to examine the diversity and complexity of the climate response within a city. This study suggests that zonal practice could be an efficient way to bridge the knowledge gap between climate research and urban planning. Urban surfaces classified by LCZ are designated as urban climate landscapes, which extends the LCZ concept to urban planning applications. Selecting Wuhan as a case study, we attempt to explore the climatic effect of landscape patterns. Thermal effects are compared across the urban climate landscapes, and the relationships between patch metrics and land surface temperature (LST are quantified. Results indicate that climate landscape layout is a considerable factor impacting local urban climate. For Wuhan, 500 m is an optimal scale for exploring landscape pattern-temperature relationships. Temperature contrast between surrounding landscape patches has a major influence on LST. Generally, fragmental landscape patches contribute to heat release. For most climate landscape types, patch metrics also have a significant effect on thermal response. When three metrics are included as predictive variables, 53.3% of the heating intensity variation can be explained for the Large Lowrise landscape, while 57.4% of the cooling intensity variation can be explained for the Water landscape. Therefore, this article claims that land-based layout optimization strategy at local scale, which conforms to planning manner, should be taken into account in terms of heat management.

Validation of the ASSERT subchannel code for prediction of CHF in standard and non-standard CANDU bundle geometries

International Nuclear Information System (INIS)

Kiteley, J.C.; Carver, M.B.; Zhou, Q.N.

1993-01-01

The ASSERT code has been developed to address the three-dimensional computation of flow and phase distribution and fuel element surface temperatures within the horizontal subchannels of CANDU PHWR fuel channels, and to provide a detailed prediction of critical heat flux distribution throughout the bundle. The ASSERT subchannel code has been validated extensively against a wide repertoire of experiments; its combination of three-dimensional prediction of local flow conditions with a comprehensive method of predicting critical heat flux (CHF) at these local conditions makes it a unique tool for predicting CHF for situations outside the existing experimental data base. In particular, ASSERT is the only tool available to systematically investigate CHF under conditions of local geometric variations, such as pressure tube creep and fuel element strain. This paper discusses the numerical methodology used in ASSERT, the constitutive relationships incorporated, and the CHF assessment methodology. The evolutionary validation plan is discussed, and early validation exercises are summarized. The paper concentrates, however, on more recent validation exercises in standard and non-standard geometries. 28 refs., 12 figs

Local government and utility firms’ debts

Directory of Open Access Journals (Sweden)

Marko Primorac

2011-12-01

Full Text Available The global financial crisis has affected the Croatian local public sector. In such circumstances, local government units’ debts and borrowing should be approached with caution. The highly interwoven financial operations of local government units and their utilities indicate the need for analysis of consolidated financial statements of local governments and utility companies in order to gain an insight into the real financial “health” of local units. Accordingly, the main aim of this paper is to analyze the size and the structure of the consolidated (local government and utility companies local public debt in Croatia. Accordingly, the paper presents the financial position of local government units supplemented with information on the financial operations of utility companies, with particular emphasis on the size and structure of their liabilities and gross and net debt. Although the current Budget Law does not require formal preparation of consolidated financial statements by local governments and their utility firms, consolidation is stipulated by International Public Sector Accounting Standards (IPSAS. The application of IPSAS regulations would be helpful in determining overall direct and indirect exposure of local government units arising from the financial operations of their utilities.

The role of entrainment in surface-atmosphere interactions over the boreal forest

Energy Technology Data Exchange (ETDEWEB)

Davis, K.J. [Minnesota Univ., St. Paul, MN (United States). Dept. of Soil Science; Lenschow, D.H.; Oncley, S.P. [National Center for Atmospheric Research, Boulder, Colorado (United States); Kiemle, C.; Ehret, G.; Giez, A. [Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Wessling (Germany). Inst. fuer Physik der Atmosphaere; Mann, J. [Risoe National Lab., Roskilde (Denmark)

1997-07-01

We present a description of the evolution of the convective boundary layer (CBL) over the boreal forests of Saskatchewan and Manitoba, as observed by the national center for atmospheric research (NCAR) Electra research aircraft during the 1994 boreal ecosystem-atmosphere study (BOREAS). All observations were made between 1530 and 2230 UT (0930-1630 local solar time, LST). We show that the CBL flux divergence often led to drying of the CBL over the course of the day, with the greatest drying (approaching 0.5 gkg{sup -1}hr{sup -1}) observed in the morning, 1000-1200 LST, and decreasing over time to nearly no drying (0 to 0.1 gkg{sup -1}hr{sup -1}) by midafternoon (1500-1600 LST). The maximum warming (0.45 Khr{sup -1}) also occurred in the morning and decreased slightly to about 0.4 Khr{sup -1} by midafternoon. The CBL vapor pressure deficit (VPD) increases over the course of the day. A significant portion of this increase can be explained by the vertical flux divergence, though horizontal advection also appears to be important. We suggest a linkage between boundary layer growth, the vertical flux divergences, and boundary layer cloud formation, with cloud activity peaking at midday in response to rapid CBL growth, then decreasing somewhat later in the day in response to CBL warming and decreased growth. We also see evidence of feedback between increasing VPD and stomatal control. (orig.) 39 refs.

A Multi-Temporal Analyses of Land Surface Temperature Using Landsat-8 Data and Open Source Software: The Case Study of Modena, Italy

Directory of Open Access Journals (Sweden)

Tommaso Barbieri

2018-05-01

Full Text Available The Urban Heat Island (UHI phenomenon, namely urban areas where the atmospheric temperature is significantly higher than in the surrounding rural areas, is currently a very well-known topic both in the scientific community and in public debates. Growing urbanization is one of the anthropic causes of UHI. The UHI phenomenon has a negative impact on the life quality of the local population (thermal discomfort, summer thermal shock, etc., thus investigations and analyses on this topic are really useful and important for correct and sustainable urban planning; this study is included in this context. A multi-temporal analysis was performed in the municipality of Modena (Italy to identify and estimate the Surface Urban Heat Island (SUHI, strictly correlated to the UHI phenomenon from 2014 to 2017. For this purpose, Landsat-8 satellite images were processed with Quantum Geographic Information System (QGIS to obtain the Land Surface Temperature (LST and the Normalized Difference Vegetation Index (NDVI. For every pixel, LST and NDVI values of three regions of interest (ROI, i.e., Countryside, Suburbs, and City Center were extracted and their correlations were investigated. A maximum variation of 6.4 °C in the LST values between City Center and Countryside was highlighted, confirming the presence of the SUHI phenomenon even in a medium-sized municipality like Modena. The implemented procedure demonstrates that satellite data are suitable for SUHI identification and estimation, therefore it could be a useful tool for public administration for urban planning policies.

Preferences for Life-Sustaining Treatments and Associations With Accurate Prognostic Awareness and Depressive Symptoms in Terminally Ill Cancer Patients' Last Year of Life.

Science.gov (United States)

Tang, Siew Tzuh; Wen, Fur-Hsing; Hsieh, Chia-Hsun; Chou, Wen-Chi; Chang, Wen-Cheng; Chen, Jen-Shi; Chiang, Ming-Chu

2016-01-01

The stability of life-sustaining treatment (LST) preferences at end of life (EOL) has been established. However, few studies have assessed preferences more than two times. Furthermore, associations of LST preferences with modifiable variables of accurate prognostic awareness, physician-patient EOL care discussions, and depressive symptoms have been investigated in cross-sectional studies only. To explore longitudinal changes in LST preferences and their associations with accurate prognostic awareness, physician-patient EOL care discussions, and depressive symptoms in terminally ill cancer patients' last year. LST preferences (cardiopulmonary resuscitation, intensive care unit [ICU] care, intubation, and mechanical ventilation) were measured approximately every two weeks. Changes in LST preferences and their associations with independent variables were examined by hierarchical generalized linear modeling with logistic regression. Participants (n = 249) predominantly rejected cardiopulmonary resuscitation, ICU care, intubation, and mechanical ventilation at EOL without significant changes as death approached. Patients with inaccurate prognostic awareness were significantly more likely than those with accurate understanding to prefer ICU care, intubation, and mechanical ventilation than to reject these LSTs. Patients with more severe depressive symptoms were less likely to prefer ICU care and to be undecided about wanting ICU care and mechanical ventilation than to reject such LSTs. LST preferences were not associated with physician-patient EOL care discussions, which were rare in our sample. LST preferences are stable in cancer patients' last year. Facilitating accurate prognostic awareness and providing adequate psychological support may counteract the increasing trend for aggressive EOL care and minimize emotional distress during EOL care decisions. Copyright © 2016 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights

Improving Land Surface Temperature Retrievals over Mountainous Regions

Directory of Open Access Journals (Sweden)

Virgílio A. Bento

2017-01-01

Full Text Available Algorithms for Land Surface Temperature (LST retrieval from infrared measurements are usually sensitive to the amount of water vapor present in the atmosphere. The Satellite Application Facilities on Climate Monitoring and Land Surface Analysis (CM SAF and LSA SAF are currently compiling a 25 year LST Climate data record (CDR, which uses water vapor information from ERA-Int reanalysis. However, its relatively coarse spatial resolution may lead to systematic errors in the humidity profiles with implications in LST, particularly over mountainous areas. The present study compares LST estimated with three different retrieval algorithms: a radiative transfer-based physical mono-window (PMW, a statistical mono-window (SMW, and a generalized split-windows (GSW. The algorithms were tested over the Alpine region using ERA-Int reanalysis data and relied on the finer spatial scale Consortium for Small-Scale Modelling (COSMO model data as a reference. Two methods were developed to correct ERA-Int water vapor misestimation: (1 an exponential parametrization of total precipitable water (TPW appropriate for SMW/GSW; and (2 a level reduction method to be used in PMW. When ERA-Int TPW was used, the algorithm missed the right TPW class in 87% of the cases. When the exponential parametrization was used, the missing class rate decreased to 9%, and when the level reduction method was applied, the LST corrections went up to 1.7 K over the study region. Overall, the correction for pixel orography in TPW leads to corrections in LST estimations, which are relevant to ensure that long-term LST records meet climate requirements, particularly over mountainous regions.

Modeling seasonal surface temperature variations in secondary tropical dry forests

Science.gov (United States)

Cao, Sen; Sanchez-Azofeifa, Arturo

2017-10-01

Secondary tropical dry forests (TDFs) provide important ecosystem services such as carbon sequestration, biodiversity conservation, and nutrient cycle regulation. However, their biogeophysical processes at the canopy-atmosphere interface remain unknown, limiting our understanding of how this endangered ecosystem influences, and responds to the ongoing global warming. To facilitate future development of conservation policies, this study characterized the seasonal land surface temperature (LST) behavior of three successional stages (early, intermediate, and late) of a TDF, at the Santa Rosa National Park (SRNP), Costa Rica. A total of 38 Landsat-8 Thermal Infrared Sensor (TIRS) data and the Surface Reflectance (SR) product were utilized to model LST time series from July 2013 to July 2016 using a radiative transfer equation (RTE) algorithm. We further related the LST time series to seven vegetation indices which reflect different properties of TDFs, and soil moisture data obtained from a Wireless Sensor Network (WSN). Results showed that the LST in the dry season was 15-20 K higher than in the wet season at SRNP. We found that the early successional stages were about 6-8 K warmer than the intermediate successional stages and were 9-10 K warmer than the late successional stages in the middle of the dry season; meanwhile, a minimum LST difference (0-1 K) was observed at the end of the wet season. Leaf phenology and canopy architecture explained most LST variations in both dry and wet seasons. However, our analysis revealed that it is precipitation that ultimately determines the LST variations through both biogeochemical (leaf phenology) and biogeophysical processes (evapotranspiration) of the plants. Results of this study could help physiological modeling studies in secondary TDFs.

Implementing necessary and sufficient standards for radioactive waste management at LLNL

International Nuclear Information System (INIS)

Sims, J.M.; Ladran, A.; Hoyt, D.

1995-01-01

Lawrence Livermore National Laboratory (LLNL) and the U.S. Department of Energy, Oakland Field Office (DOE/OAK), are participating in a pilot program to evaluate the process to develop necessary and sufficient sets of standards for contractor activities. This concept of contractor and DOE jointly and locally deciding on what constitutes the set of standards that are necessary and sufficient to perform work safely and in compliance with federal, state, and local regulations, grew out of DOE's Department Standards Committee (Criteria for the Department's Standards Program, August 1994, DOE/EH/-0416). We have chosen radioactive waste management activities as the pilot program at LLNL. This pilot includes low-level radioactive waste, transuranic (TRU) waste, and the radioactive component of low-level and TRU mixed wastes. Guidance for the development and implementation of the necessary and sufficient set of standards is provided in open-quotes The Department of Energy Closure Process for Necessary and Sufficient Sets of Standards,close quotes March 27, 1995 (draft)

Localized eigenvectors of the non-backtracking matrix

International Nuclear Information System (INIS)

Kawamoto, Tatsuro

2016-01-01

In the case of graph partitioning, the emergence of localized eigenvectors can cause the standard spectral method to fail. To overcome this problem, the spectral method using a non-backtracking matrix was proposed. Based on numerical experiments on several examples of real networks, it is clear that the non-backtracking matrix does not exhibit localization of eigenvectors. However, we show that localized eigenvectors of the non-backtracking matrix can exist outside the spectral band, which may lead to deterioration in the performance of graph partitioning. (paper: interdisciplinary statistical mechanics)

"Dark energy" in the Local Void

Science.gov (United States)

Villata, M.

2012-05-01

The unexpected discovery of the accelerated cosmic expansion in 1998 has filled the Universe with the embarrassing presence of an unidentified "dark energy", or cosmological constant, devoid of any physical meaning. While this standard cosmology seems to work well at the global level, improved knowledge of the kinematics and other properties of our extragalactic neighborhood indicates the need for a better theory. We investigate whether the recently suggested repulsive-gravity scenario can account for some of the features that are unexplained by the standard model. Through simple dynamical considerations, we find that the Local Void could host an amount of antimatter (˜5×1015 M ⊙) roughly equivalent to the mass of a typical supercluster, thus restoring the matter-antimatter symmetry. The antigravity field produced by this "dark repulsor" can explain the anomalous motion of the Local Sheet away from the Local Void, as well as several other properties of nearby galaxies that seem to require void evacuation and structure formation much faster than expected from the standard model. At the global cosmological level, gravitational repulsion from antimatter hidden in voids can provide more than enough potential energy to drive both the cosmic expansion and its acceleration, with no need for an initial "explosion" and dark energy. Moreover, the discrete distribution of these dark repulsors, in contrast to the uniformly permeating dark energy, can also explain dark flows and other recently observed excessive inhomogeneities and anisotropies of the Universe.

Variations in land surface temperature and cooling efficiency of green space in rapid urbanization

DEFF Research Database (Denmark)

Yu, Zhaowu; Guo, Xieying; Zeng, Yuxi

2018-01-01

understood. Additionally, a strategy to optimize the most significant decreased land cover type in order to maximize the cooling effect is still lacking. Therefore, in this study, we selected the rapidly urbanizing and ‘hottest’ city in China, Fuzhou, as a case study. Two algorithms were selected to compare....... This study extends the current understanding of LCC dynamics and LST variation. The concepts of the CE and TVoE are meaningful for landscape planning practice and can be used in other cases....... and obtain reliable LST data. A land use transfer matrix was used to detect critical contributions leading to the LST variations. The concept of cooling efficiency (CE) and the threshold value of efficiency (TVoE) are also proposed, defined, and calculated. The results show that LST values increased...

Least-squares reverse time migration with local Radon-based preconditioning

KAUST Repository

Dutta, Gaurav

2017-03-08

Least-squares migration (LSM) can produce images with better balanced amplitudes and fewer artifacts than standard migration. The conventional objective function used for LSM minimizes the L2-norm of the data residual between the predicted and the observed data. However, for field-data applications in which the recorded data are noisy and undersampled, the conventional formulation of LSM fails to provide the desired uplift in the quality of the inverted image. We have developed a leastsquares reverse time migration (LSRTM) method using local Radon-based preconditioning to overcome the low signal-tonoise ratio (S/N) problem of noisy or severely undersampled data. A high-resolution local Radon transform of the reflectivity is used, and sparseness constraints are imposed on the inverted reflectivity in the local Radon domain. The sparseness constraint is that the inverted reflectivity is sparse in the Radon domain and each location of the subsurface is represented by a limited number of geologic dips. The forward and the inverse mapping of the reflectivity to the local Radon domain and vice versa is done through 3D Fourier-based discrete Radon transform operators. The weights for the preconditioning are chosen to be varying locally based on the relative amplitudes of the local dips or assigned using quantile measures. Numerical tests on synthetic and field data validate the effectiveness of our approach in producing images with good S/N and fewer aliasing artifacts when compared with standard RTM or standard LSRTM.

An alternative to the standard model

International Nuclear Information System (INIS)

Baek, Seungwon; Ko, Pyungwon; Park, Wan-Il

2014-01-01

We present an extension of the standard model to dark sector with an unbroken local dark U(1) X symmetry. Including various singlet portal interactions provided by the standard model Higgs, right-handed neutrinos and kinetic mixing, we show that the model can address most of phenomenological issues (inflation, neutrino mass and mixing, baryon number asymmetry, dark matter, direct/indirect dark matter searches, some scale scale puzzles of the standard collisionless cold dark matter, vacuum stability of the standard model Higgs potential, dark radiation) and be regarded as an alternative to the standard model. The Higgs signal strength is equal to one as in the standard model for unbroken U(1) X case with a scalar dark matter, but it could be less than one independent of decay channels if the dark matter is a dark sector fermion or if U(1) X is spontaneously broken, because of a mixing with a new neutral scalar boson in the models

40 CFR 51.352 - Basic I/M performance standard.

Science.gov (United States)

2010-07-01

... following model I/M program inputs and local characteristics, such as vehicle mix and local fuel controls... current version of the EPA mobile source emission model, and shall meet the minimum performance standard... specified in 40 CFR part 85, subpart W. (8) Emission control device inspections. None. (9) Stringency. A 20...

Calculation methods' comparative analysis of monorail hoist crane local bending effects

Directory of Open Access Journals (Sweden)

Cvijović Goran M.

2016-01-01

Full Text Available The results of numerical and experimental researches of local bending problems, carried on classic and medium-wide I profiles, were a basis for the adoption of the current standards (EN 15011: 2014 which regulates the action of the local stress caused by the effect of cart wheels. Regarding the fact that IPB (HE-B wide flange profiles are largely used for production of the main carriers of monorail transport systems, this paper presents the results of the action of the local stress caused by the effect of cart wheels on the HE-A flange profile, using the methods and procedures of relevant researchers, the procedures prescribed by the standard EN 15011 as well as the results of calculations using finite element method. It has been revealed, based on comparative analysis of the results, that in the transition zone low flange / rib longitudinal local stress on the lower contour flange, determined using the above mentioned standards have tightening characteristic, while all other methods, including finite element method, give the pressing nature of the considered voltage. In addition, all of these procedures, except for the finite element method, adopt the assumption that absolute value of voltage, caused by local bending on upper and lower contour of the loaded flange, are the same, and there is no physical justification. Bearing in mind the fact that stress identification, caused by the flange local bending, is an extremely important phase proving the strength of monorail beams, we may conclude that the application of standard EN 15011 does not provide reliable results when it comes to wide flange profiles.

Conservative treatment of rectal cancer with local excision and postoperative radiation therapy

International Nuclear Information System (INIS)

Minsky, B.D.

1995-01-01

The conventional surgical treatment for patients with potentially curable transmural and/or node positive rectal cancer is a low anterior resection or abdominoperineal resection. Recently, there has been increasing interest in the use of local excision and postoperative radiation therapy as primary therapy for selected rectal cancers. The limited data suggest that the approach of local excision and postoperative radiation therapy should be limited to patients with either T 1 tumours with adverse pathological factors or T 2 tumours. Transmural tumours, which have a 24% local failure rate, are treated more effectively with standard surgery and pre- or postoperative therapy. The results of local excision and postoperative radiation therapy are encouraging, but more experience is needed to determine if this approach ultimately has similar local control and survival rates as standard surgery. (author)

Towards a test of non-locality without 'supplementary assumptions'

International Nuclear Information System (INIS)

Barbieri, M.; De Martini, F.; Di Nepi, G.; Mataloni, P.

2005-01-01

We have experimentally tested the non-local properties of the two-photon states generated by a high brilliance source of entanglement which virtually allows the direct measurement of the full set of photon pairs created by the basic QED process implied by the parametric quantum scattering. Standard Bell measurements and Bell's inequality violation test have been realized over the entire cone of emission of the degenerate pairs. By the same source we have verified Hardy's ladder theory up to the 20th step and the contradiction between the standard quantum theory and the local realism has been tested for 41% of entangled pairs

Motion and time study analysis of wooden locally manufactured ...

African Journals Online (AJOL)

Studies were carried out on time-and-motion-economy of wooden locally manufactured duplicating machines. Two versions of the machine were used for the study, viz: standard version and semi-mechanized version. Working with both auxiliary and routine operations, the standard duplicator produced printed paper at an ...

Conceptual Foundations of Improving the Living Standards of Territorial Community Based on the Introduction and Development of New Forms of Innovation and Investment Cooperation Between Regional Authorities and the Local Community

Directory of Open Access Journals (Sweden)

Popadynets, V.I.

2015-03-01

Full Text Available The main provisions have been formulated for elaboration, implementation and development of the regional target programs based on new methodological and financial resources and realization of sales of the most significant products of regional companies and organizations for the sustainable improvement of the local community living standards.

EEG source localization in full-term newborns with hypoxic-ischemia

NARCIS (Netherlands)

Jennekens, W.; Dankers, F.; Blijham, P.; Cluitmans, P.; van Pul, C.; Andriessen, P.

2013-01-01

The aim of this study was to evaluate EEG source localization by standardized weighted low-resolution brain electromagnetic tomography (swLORETA) for monitoring of fullterm newborns with hypoxic-ischemic encephalopathy, using a standard anatomic head model. Three representative examples of neonatal

Least-squares reverse time migration with local Radon-based preconditioning

KAUST Repository

Dutta, Gaurav; Giboli, Matteo; Agut, Cyril; Williamson, Paul; Schuster, Gerard T.

2017-01-01

amplitudes of the local dips or assigned using quantile measures. Numerical tests on synthetic and field data validate the effectiveness of our approach in producing images with good S/N and fewer aliasing artifacts when compared with standard RTM or standard

Effects of landscape composition and pattern on land surface temperature: An urban heat island study in the megacities of Southeast Asia.

Science.gov (United States)

Estoque, Ronald C; Murayama, Yuji; Myint, Soe W

2017-01-15

Due to its adverse impacts on urban ecological environment and the overall livability of cities, the urban heat island (UHI) phenomenon has become a major research focus in various interrelated fields, including urban climatology, urban ecology, urban planning, and urban geography. This study sought to examine the relationship between land surface temperature (LST) and the abundance and spatial pattern of impervious surface and green space in the metropolitan areas of Bangkok (Thailand), Jakarta (Indonesia), and Manila (Philippines). Landsat-8 OLI/TIRS data and various geospatial approaches, including urban-rural gradient, multiresolution grid-based, and spatial metrics-based techniques, were used to facilitate the analysis. We found a significant strong correlation between mean LST and the density of impervious surface (positive) and green space (negative) along the urban-rural gradients of the three cities, depicting a typical UHI profile. The correlation of impervious surface density with mean LST tends to increase in larger grids, whereas the correlation of green space density with mean LST tends to increase in smaller grids, indicating a stronger influence of impervious surface and green space on the variability of LST in larger and smaller areas, respectively. The size, shape complexity, and aggregation of the patches of impervious surface and green space also had significant relationships with mean LST, though aggregation had the most consistent strong correlation. On average, the mean LST of impervious surface is about 3°C higher than that of green space, highlighting the important role of green spaces in mitigating UHI effects, an important urban ecosystem service. We recommend that the density and spatial pattern of urban impervious surfaces and green spaces be considered in landscape and urban planning so that urban areas and cities can have healthier and more comfortable living urban environments. Copyright © 2016 Elsevier B.V. All rights reserved.

Spatial-temporal change of land surface temperature across 285 cities in China: An urban-rural contrast perspective.

Science.gov (United States)

Peng, Jian; Ma, Jing; Liu, Qianyuan; Liu, Yanxu; Hu, Yi'na; Li, Yingru; Yue, Yuemin

2018-09-01

As an important theme in global climate change and urban sustainable development, the changes of land surface temperature (LST) and surface urban heat island (SUHI) have been more and more focused by urban ecologists. This study used land-use data to identify the urban-rural areas in 285 cities in China and comparatively analyzed LST in urban-rural areas with the perspective of spatial-temporal dynamics heterogeneity. The results showed that, 98.9% of the cities exhibited SUHI effect in summer nighttime and the effect was stronger in northern cities than that in southern cities. In 2010, the mean SUHI intensity was the largest in summer daytime, with 4.6% of the cities having extreme SUHI of over 4°C. From 2001 to 2010, the nighttime LST of most cities increased more quickly in urban areas compared with rural areas, with an increasing tendency of the urban-rural LST difference. The difference in the urban- rural LST change rate was concentrated in the range of 0-0.1°C/year for 68.0% of cities in winter and 70.8% of cities in summer. For the higher LST increasing in urban areas compared with rural areas, there were more cities in summer than winter, indicating that the summer nighttime was the key temporal period for SUHI management. Based on the change slope of urban-rural LST, cities were clustered into four types and the vital and major zones for urban thermal environment management were identified in China. The vital zone included cities in Hunan, Hubei and other central rising provinces as well as the Beibu Gulf of Guangxi Province. The major zone included most of the cities in Central Plain Urban Agglomeration, Yangtze River Delta and Pearl River Delta. These results can provide scientific basis for SUHI adaptation in China. Copyright © 2018 Elsevier B.V. All rights reserved.

Does quality control matter? Surface urban heat island intensity variations estimated by satellite-derived land surface temperature products

Science.gov (United States)

Lai, Jiameng; Zhan, Wenfeng; Huang, Fan; Quan, Jinling; Hu, Leiqiu; Gao, Lun; Ju, Weimin

2018-05-01

The temporally regular and spatially comprehensive monitoring of surface urban heat islands (SUHIs) have been extremely difficult, until the advent of satellite-based land surface temperature (LST) products. However, these LST products have relatively higher errors compared to in situ measurements. This has resulted in comparatively inaccurate estimations of SUHI indicators and, consequently, may have distorted interpretations of SUHIs. Although reports have shown that LST qualities are important for SUHI interpretations, systematic investigations of the response of SUHI indicators to LST qualities across cities with dissimilar bioclimates are rare. To address this issue, we chose eighty-six major cities across mainland China and analyzed SUHI intensity (SUHII) derived from Moderate Resolution Imaging Spectroradiometer (MODIS) LST data. The LST-based SUHII differences due to inclusion or exclusion of MODIS quality control (QC) flags (i.e., ΔSUHII) were evaluated. Our major findings included, but are not limited to, the following four aspects: (1) SUHIIs can be significantly impacted by MODIS QC flags, and the associated QC-induced ΔSUHIIs generally accounted for 24.3% (29.9%) of the total SUHII value during the day (night); (2) the ΔSUHIIs differed between seasons, with considerable differences between transitional (spring and autumn) and extreme (summer and winter) seasons; (3) significant discrepancies also appeared among cities located in northern and southern regions, with northern cities often possessing higher annual mean ΔSUHIIs. The internal variations of ΔSUHIIs within individual cities also showed high heterogeneity, with ΔSUHII variations that generally exceeded 5.0 K (3.0 K) in northern (southern) cities; (4) ΔSUHIIs were negatively related to SUHIIs and cloud cover percentages (mostly in transitional seasons). No significant relationship was found in the extreme seasons. Our findings highlight the need to be extremely cautious when using LST

Geometrically engineering the standard model: Locally unfolding three families out of E8

International Nuclear Information System (INIS)

Bourjaily, Jacob L.

2007-01-01

This paper extends and builds upon the results of [J. L. Bourjaily, arXiv:0704.0444.], in which we described how to use the tools of geometrical engineering to deform geometrically engineered grand unified models into ones with lower symmetry. This top-down unfolding has the advantage that the relative positions of singularities giving rise to the many 'low-energy' matter fields are related by only a few parameters which deform the geometry of the unified model. And because the relative positions of singularities are necessary to compute the superpotential, for example, this is a framework in which the arbitrariness of geometrically engineered models can be greatly reduced. In [J. L. Bourjaily, arXiv:0704.0444.], this picture was made concrete for the case of deforming the representations of an SU 5 model into their standard model content. In this paper we continue that discussion to show how a geometrically engineered 16 of SO 10 can be unfolded into the standard model, and how the three families of the standard model uniquely emerge from the unfolding of a single, isolated E 8 singularity

NASA's MODIS/VIIRS Land Surface Temperature and Emissivity Products: Asssessment of Accuracy, Continuity and Science Uses

Science.gov (United States)

Hulley, G. C.; Malakar, N.; Islam, T.

2017-12-01

Land Surface Temperature and Emissivity (LST&E) are an important Earth System Data Record (ESDR) and Environmental Climate Variable (ECV) defined by NASA and GCOS respectively. LST&E data are key variables used in land cover/land use change studies, in surface energy balance and atmospheric water vapor retrieval models and retrievals, and in climate research. LST&E products are currently produced on a routine basis using data from the MODIS instruments on the NASA EOS platforms and by the VIIRS instrument on the Suomi-NPP platform that serves as a bridge between NASA EOS and the next-generation JPSS platforms. Two new NASA LST&E products for MODIS (MxD21) and VIIRS (VNP21) are being produced during 2017 using a new approach that addresses discrepancies in accuracy and consistency between the current suite of split-window based LST products. The new approach uses a Temperature Emissivity Separation (TES) algorithm, originally developed for the ASTER instrument, to physically retrieve both LST and spectral emissivity consistently for both sensors with high accuracy and well defined uncertainties. This study provides a rigorous assessment of accuracy of the MxD21/VNP21 products using temperature- and radiance-based validation strategies and demonstrates continuity between the products using collocated matchups over CONUS. We will further demonstrate potential science use of the new products with studies related to heat waves, monitoring snow melt dynamics, and land cover/land use change.

THE EFFECTS OF BUILT-UP AND GREEN AREAS ON THE LAND SURFACE TEMPERATURE OF THE KUALA LUMPUR CITY

Directory of Open Access Journals (Sweden)

N. A. Isa

2017-10-01

Full Text Available A common consequence of rapid and uncontrollable urbanization is Urban Heat Island (UHI. It occurs due to the negligence on climate behaviour which degrades the quality of urban climate condition. Recently, addressing urban climate in urban planning through mapping has received worldwide attention. Therefore, the need to identify the significant factors is a must. This study aims to analyse the relationships between Land Surface Temperature (LST and two urban parameters namely built-up and green areas. Geographical Information System (GIS and remote sensing techniques were used to prepare the necessary data layers required for this study. The built-up and the green areas were extracted from Landsat 8 satellite images either using the Normalized Difference Built-Up Index (NDBI, Normalized Difference Vegetation Index (NDVI or Modified Normalize Difference Water Index (MNDWI algorithms, while the mono-window algorithm was used to retrieve the Land Surface Temperature (LST. Correlation analysis and Multi-Linear Regression (MLR model were applied to quantitatively analyse the effects of the urban parameters. From the study, it was found that the two urban parameters have significant effects on the LST of Kuala Lumpur City. The built-up areas have greater influence on the LST as compared to the green areas. The built-up areas tend to increase the LST while green areas especially the densely vegetated areas help to reduce the LST within an urban areas. Future studies should focus on improving existing urban climatic model by including other urban parameters.

Downscaling Meteosat Land Surface Temperature over a Heterogeneous Landscape Using a Data Assimilation Approach

Directory of Open Access Journals (Sweden)

Rihab Mechri

2016-07-01

Full Text Available A wide range of environmental applications require the monitoring of land surface temperature (LST at frequent intervals and fine spatial resolutions, but these conditions are not offered nowadays by the available space sensors. To overcome these shortcomings, LST downscaling methods have been developed to derive higher resolution LST from the available satellite data. This research concerns the application of a data assimilation (DA downscaling approach, the genetic particle smoother (GPS, to disaggregate Meteosat 8 LST time series (3 km × 5 km at finer spatial resolutions. The methodology was applied over the Crau-Camargue region in Southeastern France for seven months in 2009. The evaluation of the downscaled LSTs has been performed at a moderate resolution using a set of coincident clear-sky MODIS LST images from Aqua and Terra platforms (1 km × 1 km and at a higher resolution using Landsat 7 data (60 m × 60 m. The performance of the downscaling has been assessed in terms of reduction of the biases and the root mean square errors (RMSE compared to prior model-simulated LSTs. The results showed that GPS allows downscaling the Meteosat LST product from 3 × 5 km2 to 1 × 1 km2 scales with a RMSE less than 2.7 K. Finer scale downscaling at Landsat 7 resolution showed larger errors (RMSE around 5 K explained by land cover errors and inter-calibration issues between sensors. Further methodology improvements are finally suggested.

The role of religious beliefs in ethics committee consultations for conflict over life-sustaining treatment.

Science.gov (United States)

Bandini, Julia I; Courtwright, Andrew; Zollfrank, Angelika A; Robinson, Ellen M; Cadge, Wendy

2017-06-01

Previous research has suggested that individuals who identify as being more religious request more aggressive medical treatment at end of life. These requests may generate disagreement over life-sustaining treatment (LST). Outside of anecdotal observation, however, the actual role of religion in conflict over LST has been underexplored. Because ethics committees are often consulted to help mediate these conflicts, the ethics consultation experience provides a unique context in which to investigate this question. The purpose of this paper was to examine the ways religion was present in cases involving conflict around LST. Using medical records from ethics consultation cases for conflict over LST in one large academic medical centre, we found that religion can be central to conflict over LST but was also present in two additional ways through (1) religious coping, including a belief in miracles and support from a higher power, and (2) chaplaincy visits. In-hospital mortality was not different between patients with religiously versus non-religiously centred conflict. In our retrospective cohort study, religion played a variety of roles and did not lead to increased treatment intensity or prolong time to death. Ethics consultants and healthcare professionals involved in these cases should be cognisant of the complex ways that religion can manifest in conflict over LST. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Remote sensing study of the impact of vegetation on thermal environment in different contexts

Science.gov (United States)

Xie, Qijiao; Wu, Yingjiao; Zhou, Zhixiang; Wang, Zhengxiang

2018-02-01

Satellite remote sensing technology provides informative data for detecting the land surface temperature (LST) distribution and urban heat island (UHI) effect remotely and regionally. In this study, two Landsat Thematic Mapper (TM) images acquired on September 26, 1987 and September 17, 2013 were used to derive LST and the normalized difference vegetation index (NDVI) values in Wuhan, China. The relationships between NDVI and LST were examined in different contexts, namely built-up area, farmland, grassland and forest. Results showed that negative correlations between the mean NDVI and LST were detected in all observed land covers, which meant that vegetation was efficient in decreasing surface temperatures and mitigating UHI effect. The cooling efficiency of vegetation on thermal environment varied with different contexts. As mean NDVI increased at each 0.1, the decreased LST values in built-up area, farmland, grassland and forest were 1.4 °C, 1.4 °C, 1.1 °C, 1.9 °C in 1987 and 1.4 °C, 1.7 °C, 1.3 °C, 1.8 °C in 2013, respectively. This finding encourages urban planners and greening designers to devote more efforts in protecting urban forests.

Landsat Science Team meeting: Winter 2015

Science.gov (United States)

Schroeder, Todd A.; Loveland, Thomas; Wulder, Michael A.; Irons, James R.

2015-01-01

The summer meeting of the joint U.S. Geological Survey (USGS)–NASA Landsat Science Team (LST) was held at the USGS’s Earth Resources Observation and Science (EROS) Center July 7-9, 2015, in Sioux Falls, SD. The LST co-chairs, Tom Loveland [EROS—Senior Scientist] and Jim Irons [NASA’s Goddard Space Flight Center (GSFC)—Landsat 8 Project Scientist], opened the three-day meeting on an upbeat note following the recent successful launch of the European Space Agency’s Sentinel-2 mission on June 23, 2015 (see image on page 14), and the news that work on Landsat 9 has begun, with a projected launch date of 2023.With over 60 participants in attendance, this was the largest LST meeting ever held. Meeting topics on the first day included Sustainable Land Imaging and Landsat 9 development, Landsat 7 and 8 operations and data archiving, the Landsat 8 Thermal Infrared Sensor (TIRS) stray-light issue, and the successful Sentinel-2 launch. In addition, on days two and three the LST members presented updates on their Landsat science and applications research. All presentations are available at landsat.usgs.gov/science_LST_Team_ Meetings.php.

STANDARDIZATION OR ADAPTATION IN COSMETICS WEBSITES MARKETING ? AN EMPIRICAL STUDY.

Directory of Open Access Journals (Sweden)

Anca Constantinescu-Dobra

2011-06-01

Full Text Available The websites marketing is becoming an important tool both for multinationals and SMEs, in their effort to internationalizing their business.This study focuses on the international opportunities that are present within the European markets. The paper aims at identifying the degree of websites marketing standardization vs. adaptation, as a marketing tool for cosmetic products. Moreover, the study examines in a comparative manner the standardization strategy of multinationals and small and medium enterprises (SMEs, leaders in European markets, for different cosmetic cathegories.The evaluation of online advertising standardization is based on the modified Model for Testing Advertising Standardization, developed by Whitelock and Chung. The web sites degree of localizations areanalyzed based upon 98 criteria, as resulted from an adapted methodology of ProfNet Institut fur Internet Marketing, Munster (Germany. The sample includes the 101 leaders from European markets.The research outcomes reflect a standardized websites marketing policy for SMEs and localized for multinationals. Also, for perfumes, dental care products and toiletry, European cosmetic leaders implementstandardized websites marketing policies and balanced for the other cosmetics categories. The hypothesis concerning a strong correlation between standardization and handling dimension was supported.

24 CFR 92.251 - Property standards.

Science.gov (United States)

2010-04-01

..., as applicable, one of three model codes: Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI); or the Council of American Building Officials (CABO) one or two...) Housing that is constructed or rehabilitated with HOME funds must meet all applicable local codes...

Nonlinear dynamics of the relativistic standard map

International Nuclear Information System (INIS)

Nomura, Y.; Ichikawa, Y.H.; Horton, W.

1991-04-01

Heating and acceleration of charged particles by RF fields have been extensively investigated by the standard map. The question arises as to how the relativistic effects change the nonlinear dynamical behavior described by the classical standard map. The relativistic standard map is a two parameter (K, Β = ω/kc) family of dynamical systems reducing to the standard map when Β → 0. For Β ≠ 0 the relativistic mass increase suppresses the onset of stochasticity. It shown that the speed of light limits the rate of advance of the phase in the relativistic standard map and introduces KAM surfaces persisting in the high momentum region. An intricate structure of mixing in the higher order periodic orbits and chaotic orbits is analyzed using the symmetry properties of the relativistic standard map. The interchange of the stability of the periodic orbits in the relativistic standard map is also observed and is explained by the local linear stability of the orbits. 12 refs., 16 figs

The Trends and Prospects of Health Information Standards : Standardization Analysis and Suggestions

International Nuclear Information System (INIS)

Kim, Chang Soo

2008-01-01

Ubiquitous health care system, which is one of the developing solution technologies of IT, BT and NT, could give us new medical environments in future. Implementing health information systems can be complex, expensive and frustrating. Healthcare professionals seeking to acquire or upgrade systems do not have a convenient, reliable way of specifying a level of adherence to communication standards sufficient to achieve truly efficient interoperability. Great progress has been made in establishing such standards-DICOM, IHE and HL7, notably, are now highly advanced. IHE has defined a common framework to deliver the basic interoperability needed for local and regional health information networks. It has developed a foundational set of standards-based integration profiles for information exchange with three interrelated efforts. HL7 is one of several ANSI-accredited Standards Developing Organizations operating in the healthcare arena. Most SDOs produce standards (protocols) for a particular healthcare domain such as pharmacy, medical devices, imaging or insurance transactions. HL7's domain is clinical and administrative data. HL7 is an international community of healthcare subject matter experts and information scientists collaborating to create standards for the exchange, management and integration of electronic healthcare information. The ASTM specification for Continuity of Care Record was developed by subcommittee E31.28 on electronic health records, which includes clinicians, provider institutions, administrators, patient advocates, vendors, and health industry. In this paper, there are suggestions that provide a test bed, demonstration and specification of how standards such a IHE, HL7, ASTM can be used to provide an integrated environment.

The Trends and Prospects of Health Information Standards : Standardization Analysis and Suggestions

Energy Technology Data Exchange (ETDEWEB)

Kim, Chang Soo [Dept. of Radiological Science, College of Health Science, Catholic University of Pusan, Pusan (Korea, Republic of)

2008-03-15

Ubiquitous health care system, which is one of the developing solution technologies of IT, BT and NT, could give us new medical environments in future. Implementing health information systems can be complex, expensive and frustrating. Healthcare professionals seeking to acquire or upgrade systems do not have a convenient, reliable way of specifying a level of adherence to communication standards sufficient to achieve truly efficient interoperability. Great progress has been made in establishing such standards-DICOM, IHE and HL7, notably, are now highly advanced. IHE has defined a common framework to deliver the basic interoperability needed for local and regional health information networks. It has developed a foundational set of standards-based integration profiles for information exchange with three interrelated efforts. HL7 is one of several ANSI-accredited Standards Developing Organizations operating in the healthcare arena. Most SDOs produce standards (protocols) for a particular healthcare domain such as pharmacy, medical devices, imaging or insurance transactions. HL7's domain is clinical and administrative data. HL7 is an international community of healthcare subject matter experts and information scientists collaborating to create standards for the exchange, management and integration of electronic healthcare information. The ASTM specification for Continuity of Care Record was developed by subcommittee E31.28 on electronic health records, which includes clinicians, provider institutions, administrators, patient advocates, vendors, and health industry. In this paper, there are suggestions that provide a test bed, demonstration and specification of how standards such a IHE, HL7, ASTM can be used to provide an integrated environment.

Open hemorrhoidectomy under local anesthesia for symptomatic ...

African Journals Online (AJOL)

standard treatment for prolapsed hemorrhoids. The procedure is commonly done under general or regional anesthesia. This study is aimed to assess the feasibility and tolerability of open – hemorrhoidectomy under local anaesthesia in our setting.

Further experience with the local lymph node assay using standard radioactive and nonradioactive cell count measurements.

Science.gov (United States)

Kolle, Susanne N; Basketter, David; Schrage, Arnhild; Gamer, Armin O; van Ravenzwaay, Bennard; Landsiedel, Robert

2012-08-01

In a previous study, the predictive capacity of a modified local lymph node assay (LLNA) based on cell counts, the LNCC, was demonstrated to be closely similar to that of the original assay. In addition, a range of substances, including some technical/commercial materials and a range of agrochemical formulations (n = 180) have also been assessed in both methods in parallel. The results in the LNCC and LLNA were generally consistent, with 86% yielding an identical classification outcome. Discordant results were associated with borderline data and were evenly distributed between the two methods. Potency information derived from each method also demonstrated good consistency (n = 101), with 93% of predictions being close. Skin irritation was observed only infrequently and was most commonly associated with positive results; it was not associated with the discordant results. Where different vehicles were used with the same test material, the effect on sensitizing activity was modest, consistent with historical data. Analysis of positive control data indicated that the LNCC and LLNA displayed similar levels of biological variation. When taken in combination with the previously published results on LLNA Performance Standard chemicals, it is concluded that the LNCC provides a viable non-radioactive alternative to the LLNA for the assessment of substances, including potency predictions, as well as for the evaluation of preparations. Copyright © 2012 John Wiley & Sons, Ltd.

Unmanned airborne thermal and mutilspectral imagery for estimating evapotranspiration in irrigated vineyards

Science.gov (United States)

Thermal-infrared remote sensing of land surface temperature (LST) provides valuable information for quantifying rootzone water availability, evapotranspiration (ET) and crop condition. This paper describes the most recent modifications applied to the robust but relatively simple LST-based energy bal...

Integração de imagens NOAA/AVHRR: rede de cooperação para monitoramento nacional da safra de soja Integration of NOAA/AVHRR images: cooperation network towards national soybean crop monitoring

Directory of Open Access Journals (Sweden)

Anibal Gusso

2013-04-01

Full Text Available Uma avaliação inicial das condições do desenvolvimento da safra nacional, enquanto as plantas ainda estão nos campos, é altamente necessária para o cálculo correto das projeções na tomada de decisão e políticas relacionadas com o planejamento governamental e segurança alimentar. O objetivo deste trabalho foi avaliar a adequação dos dados NOAA/AVHRR (National Oceanic and Atmospheric Administration / Advanced Very High Resolution Radiometer em detectar mudanças nas condições da vegetação, devidas à ocorrência de estresse hídrico, na soja, por meio de uma combinação do índice NDVI (Normalized Difference Vegetation Index e da LST (Land Surface Temperature. Os dados LST e NDVI foram combinados e comparados pixel a pixel, sobre uma área de cultivo de soja, no Rio Grande do Sul. A relação teórica inversa prevista na combinação de LST e NDVI foi detectada. Foi observado que ocorre um aumento médio na LST em uma safra de ciclo normal (de 301,02 K para 308,36 K, quando comparada a uma safra sob condição de estresse hídrico, no desenvolvimento da cultura. Uma redução média do NDVI foi observada no ciclo normal (de 0,65 para 0,53, comparada com uma safra sob efeitos ocasionados pela estiagem no desenvolvimento da cultura. Foi observado maior correlação da produtividade municipal com LST (R2=0,78 do que com o NDVI (R2 = 0,59. Os resultados obtidos indicam que a integração de imagens do sensor AVHRR, proveniente de diferentes instituições, proporciona a adequada combinação espacial e temporal dos dados LST e NDVI, a fim de detectar a ocorrência de estresse hídrico, bem como sua intensidade, caracterizando as condições do ciclo de desenvolvimento da soja.An early assessment of national crop development conditions while the plants are still in the fields is highly needed to calculate correctly projections for decision-making and policies related to government planning and food security. The aim of this study

Food Standards are Good– for Middle-class Farmers

DEFF Research Database (Denmark)

Hansen, Henrik; Trifkovic, Neda

results indicate that large returns can be accrued from food standards, but only for the upper middle-class farmers, i.e., those between the 50% and 85% quantiles of the expenditure distribution. Overall, our result points to an exclusionary impact of standards for the poorest farmers while the richest do......We estimate the causal effect of food standards on Vietnamese pangasius farmers’ wellbeing measured by per capita consumption expenditure. We estimate both the average effects and the local average treatment effects on poorer and richer farmers by instrumental variable quantile regression. Our...

GASB proposes new standards for financial reporting of postemployment benefits by state and local governments.

Science.gov (United States)

Johnson, Karl D

2003-03-01

GASB has proposed new standards that will affect the way in which governments report postemployment health care benefits in audited external financial statements, resulting in more complete and transparent reporting by employers and plans and more relevant and useful information for the users of governmental financial reports. This article provides an overview of current financial reporting standards and practice, the financial reporting objectives of the project, the proposed measurement approach, noteworthy specific proposals, and the projected timetable for completion of the project and implementation of the new standards.

Interrogating Social Sustainability in the Biofuels Sector in Latin America: Tensions Between Global Standards and Local Experiences in Mexico, Brazil, and Colombia

Science.gov (United States)

Selfa, Theresa; Bain, Carmen; Moreno, Renata; Eastmond, Amarella; Sweitz, Sam; Bailey, Conner; Pereira, Gustavo Simas; Souza, Tatiana; Medeiros, Rodrigo

2015-12-01

Across the Americas, biofuels production systems are diverse due to geographic conditions, historical patterns of land tenure, different land use patterns, government policy frameworks, and relations between the national state and civil society, all of which shape the role that biofuels play in individual nations. Although many national governments throughout the Americas continue to incentivize growth of the biofuels industry, one key challenge for biofuels sustainability has been concern about its social impacts. In this article, we discuss some of the key social issues and tensions related to the recent expansion of biofuels production in Mexico, Colombia, and Brazil. We argue that a process of "simplification" of ecological and cultural diversity has aided the expansion of the biofuels frontier in these countries, but is also undermining their viability. We consider the ability of governments and non-state actors in multi-stakeholder initiatives (MSI) to address social and environmental concerns that affect rural livelihoods as a result of biofuels expansion. We analyze the tensions between global sustainability standards, national level policies for biofuels development, and local level impacts and visions of sustainability. We find that both government and MSI efforts to address sustainability concerns have limited impact, and recommend greater incorporation of local needs and expertise to improve governance.

Interrogating Social Sustainability in the Biofuels Sector in Latin America: Tensions Between Global Standards and Local Experiences in Mexico, Brazil, and Colombia.

Science.gov (United States)

Selfa, Theresa; Bain, Carmen; Moreno, Renata; Eastmond, Amarella; Sweitz, Sam; Bailey, Conner; Pereira, Gustavo Simas; Souza, Tatiana; Medeiros, Rodrigo

2015-12-01

Across the Americas, biofuels production systems are diverse due to geographic conditions, historical patterns of land tenure, different land use patterns, government policy frameworks, and relations between the national state and civil society, all of which shape the role that biofuels play in individual nations. Although many national governments throughout the Americas continue to incentivize growth of the biofuels industry, one key challenge for biofuels sustainability has been concern about its social impacts. In this article, we discuss some of the key social issues and tensions related to the recent expansion of biofuels production in Mexico, Colombia, and Brazil. We argue that a process of "simplification" of ecological and cultural diversity has aided the expansion of the biofuels frontier in these countries, but is also undermining their viability. We consider the ability of governments and non-state actors in multi-stakeholder initiatives (MSI) to address social and environmental concerns that affect rural livelihoods as a result of biofuels expansion. We analyze the tensions between global sustainability standards, national level policies for biofuels development, and local level impacts and visions of sustainability. We find that both government and MSI efforts to address sustainability concerns have limited impact, and recommend greater incorporation of local needs and expertise to improve governance.

Characterizing the Spatio-Temporal Pattern of Land Surface Temperature through Time Series Clustering: Based on the Latent Pattern and Morphology

Directory of Open Access Journals (Sweden)

Huimin Liu

2018-04-01

Full Text Available Land Surface Temperature (LST is a critical component to understand the impact of urbanization on the urban thermal environment. Previous studies were inclined to apply only one snapshot to analyze the pattern and dynamics of LST without considering the non-stationarity in the temporal domain, or focus on the diurnal, seasonal, and annual pattern analysis of LST which has limited support for the understanding of how LST varies with the advancing of urbanization. This paper presents a workflow to extract the spatio-temporal pattern of LST through time series clustering by focusing on the LST of Wuhan, China, from 2002 to 2017 with a 3-year time interval with 8-day MODerate-resolution Imaging Spectroradiometer (MODIS satellite image products. The Latent pattern of LST (LLST generated by non-parametric Multi-Task Gaussian Process Modeling (MTGP and the Multi-Scale Shape Index (MSSI which characterizes the morphology of LLST are coupled for pattern recognition. Specifically, spatio-temporal patterns are discovered after the extraction of spatial patterns conducted by the incorporation of k -means and the Back-Propagation neural networks (BP-Net. The spatial patterns of the 6 years form a basic understanding about the corresponding temporal variances. For spatio-temporal pattern recognition, LLSTs and MSSIs of the 6 years are regarded as geo-referenced time series. Multiple algorithms including traditional k -means with Euclidean Distance (ED, shape-based k -means with the constrained Dynamic Time Warping ( c DTW distance measure, and the Dynamic Time Warping Barycenter Averaging (DBA centroid computation method ( k - c DBA and k -shape are applied. Ten external indexes are employed to evaluate the performance of the three algorithms and reveal k - c DBA as the optimal time series clustering algorithm for our study. The study area is divided into 17 geographical time series clusters which respectively illustrate heterogeneous temporal dynamics of LST

Study of Volcanic Activity at Different Time Scales Using Hypertemporal Land Surface Temperature Data

NARCIS (Netherlands)

Pavlidou, Efthymia; Hecker, Chris; van der Werff, Harald; van der Meijder, Mark

2017-01-01

We apply a method for detecting subtle spatiotemporal signal fluctuations to monitor volcanic activity. Whereas midwave infrared data are commonly used for volcanic hot spot detection, our approach utilizes hypertemporal longwave infrared-based land surface temperature (LST) data. Using LST data of

47 CFR 76.1717 - Compliance with technical standards.

Science.gov (United States)

2010-10-01

... with technical standards. Each system operator shall be prepared to show, on request by an authorized representative of the Commission or the local franchising authority, that the system does, in fact, comply with...

Necessary and Sufficient Process leading to Work Smart Standards. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-01

The Necessary and Sufficient Process leading to Work Smart Standards is a Department of Energy initiative to assure adequate protection for workers, the public, and the environment. The Work Smart Standards initiative directs the Laboratory to develop a set of ES and H standards based on the work performed at the Laboratory and the hazards associated with the work. Berkeley Lab`s set of Work Smart Standards includes required Federal, State and local laws and, additionally, national and international standards which represent the highest operating standards of industrial and commercial institutions.

Necessary and Sufficient Process leading to Work Smart Standards. Final report

International Nuclear Information System (INIS)

1996-11-01

The Necessary and Sufficient Process leading to Work Smart Standards is a Department of Energy initiative to assure adequate protection for workers, the public, and the environment. The Work Smart Standards initiative directs the Laboratory to develop a set of ES and H standards based on the work performed at the Laboratory and the hazards associated with the work. Berkeley Lab's set of Work Smart Standards includes required Federal, State and local laws and, additionally, national and international standards which represent the highest operating standards of industrial and commercial institutions

Refining Preoperative Therapy for Locally Advanced Rectal Cancer

Science.gov (United States)

In the PROSPECT trial, patients with locally advanced, resectable rectal cancer will be randomly assigned to receive either standard neoadjuvant chemoradiation therapy or neoadjuvant FOLFOX chemotherapy, with chemoradiation reserved for nonresponders.

[Applicability of traditional landscape metrics in evaluating urban heat island effect].

Science.gov (United States)

Chen, Ai-Lian; Sun, Ran-Hao; Chen, Li-Ding

2012-08-01

By using 24 landscape metrics, this paper evaluated the urban heat island effect in parts of Beijing downtown area. QuickBird (QB) images were used to extract the landscape type information, and the thermal bands from Landsat Enhanced Thematic Mapper Plus (ETM+) images were used to extract the land surface temperature (LST) in four seasons of the same year. The 24 landscape pattern metrics were calculated at landscape and class levels in a fixed window with 120 mx 120 m in size, with the applicability of these traditional landscape metrics in evaluating the urban heat island effect examined. Among the 24 landscape metrics, only the percentage composition of landscape (PLAND), patch density (PD), largest patch index (LPI), coefficient of Euclidean nearest-neighbor distance variance (ENN_CV), and landscape division index (DIVISION) at landscape level were significantly correlated with the LST in March, May, and November, and the PLAND, LPI, DIVISION, percentage of like adjacencies, and interspersion and juxtaposition index at class level showed significant correlations with the LST in March, May, July, and December, especially in July. Some metrics such as PD, edge density, clumpiness index, patch cohesion index, effective mesh size, splitting index, aggregation index, and normalized landscape shape index showed varying correlations with the LST at different class levels. The traditional landscape metrics could not be appropriate in evaluating the effects of river on LST, while some of the metrics could be useful in characterizing urban LST and analyzing the urban heat island effect, but screening and examining should be made on the metrics.

Development of local TDC model in core thermal hydraulic analysis

International Nuclear Information System (INIS)

Kwon, H.S.; Park, J.R.; Hwang, D.H.; Lee, S.K.

2004-01-01

The local TDC model consisting of natural mixing and forced mixing part was developed to obtain more realistic local fluid properties in the core subchannel analysis. To evaluate the performance of local TDC model, the CHF prediction capability was tested with the various CHF correlations and local fluid properties at CHF location which are based on the local TDC model. The results show that the standard deviation of measured to predicted CHF ratio (M/P) based on local TDC model can be reduced by about 7% compared to those based on global TDC model when the CHF correlation has no term to account for distance from the spacer grid. (author)

Standardization of 8-color flow cytometry across different flow cytometer instruments: A feasibility study in clinical laboratories in Switzerland.

Science.gov (United States)

Glier, Hana; Heijnen, Ingmar; Hauwel, Mathieu; Dirks, Jan; Quarroz, Stéphane; Lehmann, Thomas; Rovo, Alicia; Arn, Kornelius; Matthes, Thomas; Hogan, Cassandra; Keller, Peter; Dudkiewicz, Ewa; Stüssi, Georg; Fernandez, Paula

2017-07-29

The EuroFlow Consortium developed a fully standardized flow cytometric approach from instrument settings, through antibody panel, reagents and sample preparation protocols, to data acquisition and analysis. The Swiss Cytometry Society (SCS) promoted a study to evaluate the feasibility of using such standardized measurements of 8-color data across two different flow cytometry platforms - Becton Dickinson (BD) FACSCanto II and Beckman Coulter (BC) Navios, aiming at increasing reproducibility and inter-laboratory comparability of immunophenotypic data in clinical laboratories in Switzerland. The study was performed in two phases, i.e. a learning phase (round 1) and an analytical phase (rounds 2 and 3) consisting of a total of three rounds. Overall, 10 laboratories using BD FACSCanto II (n=6) or BC Navios (n=4) flow cytometers participated. Each laboratory measured peripheral blood samples from healthy donors stained with a uniform antibody panel of reagents - EuroFlow Lymphoid Screening Tube (LST) - applying the EuroFlow standardized protocols for instrument setup and sample preparation (www.EuroFlow.org). All data files were analyzed centrally and median fluorescence intensity (MedFI) values for individual markers on defined lymphocyte subsets were recorded; variability from reference MedFI values was assessed using performance scores. Data troubleshooting and discussion of the results with the participants followed after each round at SCS meetings. The results of the learning phase demonstrated that standardized instrument setup and data acquisition are feasible in routine clinical laboratories without previous experience with EuroFlow. During the analytical phase, highly comparable data were obtained at the different laboratories using either BD FACSCanto II or BC Navios. The coefficient of variation of MedFI for 7 of 11 markers performed repeatedly below 30%. In the last study round, 89% of participants scored over 90% MedFI values within the acceptance criteria

Angiofibroma Localized in the Sphenoid Sinus

Directory of Open Access Journals (Sweden)

Alper Yenigun

2017-01-01

Full Text Available Juvenile nasopharyngeal angiofibroma is the most common benign tumor of the nasopharynx with complaints of unilateral nasal obstruction and recurrent nosebleeds in the young male population. Despite being a benign tumor, it can be aggressively destructive in surrounding tissues and bones by acting locally. The gold standard treatment method is the surgical excision of the tumor. This case report is a case of angiofibroma, a 32-year-old asymptomatic male patient with no evidence of clinical signs and endoscopic examination, which is recognized as a localized vascular mass lesion in the right sphenoid sinus on the cranial MR imaging. We prepared this case report that may represent an angiofibroma localized only within the sphenoid sinus which is very rare in the literature.

Angiofibroma Localized in the Sphenoid Sinus

Science.gov (United States)

Aksoy, Fadlullah; Vural, Omer; Ozturan, Orhan

2017-01-01

Juvenile nasopharyngeal angiofibroma is the most common benign tumor of the nasopharynx with complaints of unilateral nasal obstruction and recurrent nosebleeds in the young male population. Despite being a benign tumor, it can be aggressively destructive in surrounding tissues and bones by acting locally. The gold standard treatment method is the surgical excision of the tumor. This case report is a case of angiofibroma, a 32-year-old asymptomatic male patient with no evidence of clinical signs and endoscopic examination, which is recognized as a localized vascular mass lesion in the right sphenoid sinus on the cranial MR imaging. We prepared this case report that may represent an angiofibroma localized only within the sphenoid sinus which is very rare in the literature. PMID:29359061

Local supersymmetry in non-relativistic systems

International Nuclear Information System (INIS)

Urrutia, L.F.; Zanelli, J.

1989-10-01

Classical and quantum non-relativistic interacting systems invariant under local supersymmetry are constructed by the method of taking square roots of the bosonic constraints which generate timelike reparametrization, leaving the action unchanged. In particular, the square root of the Schroedinger constraint is shown to be the non-relativistic limit of the Dirac constraint. Contact is made with the standard models of Supersymmetric Quantum Mechanics through the reformulation of the locally invariant systems in terms of their true degrees of freedom. Contrary to the field theory case, it is shown that the locally invariant systems are completely equivalent to the corresponding globally invariant ones, the latter being the Heisenberg picture description of the former, with respect to some fermionic time. (author). 14 refs

Treatment of locally advanced/locally recurrent breast cancer and inflammatory breast cancer

International Nuclear Information System (INIS)

Murakami, Masao

2000-01-01

This paper summarizes the treatment of locally advanced breast cancer, inflammatory breast cancer, and locally recurrent breast cancer. A multidisciplinary approach considering subclinical distant metastases is needed to treat these types of breast cancer. Subclinical distant metastasis is observed in about 80% of case of locally advanced cancer, and treatment of subclinical distant metastases, e.g., by endocrinotherapy and chemotherapy, is therefore essential to improving the prognosis. The standard therapy for unresectable locally advanced breast cancer consists of induction chemotherapy with anthracyclines and local treatment with mastectomy or irradiation. Previous reports have stated that induction chemotherapy was effective in 60-80% of the primary lesions or lymph node metastasis, and the CR rates were in the 10-20% range. Combination therapy with induction chemotherapy clearly improved the outcome over local treatment alone. The usual irradiation dose is 50 to 60 Gy/5 to 7 weeks to the whole breast or the thoracic wall. Boost irradiation at a dose of 10 to 25 Gy is performed in unresectable cases. The boost irradiation dose to the lymph node area is usually 45 to 50 Gy/5 to 6 weeks in cases without gross lesions and 10 to 15 Gy in cases with gross lesions. Combination therapy consisting of conservative pectoral mastectomy and postoperative adjuvant chemo- endocrino-therapy (i.e., adjuvant therapy) has become the standard regimen for treating resectable locally advanced breast cancer, because it significantly improves the recurrence rate and survival rate compared to local treatment alone. Some clinical have studies indicated that neoadjuvant therapy (i.e., induction chemotherapy + surgery/radiation therapy) is comparable or superior to adjuvant therapy in terms of improving the prognosis. However, the efficacy and most appropriate method of breast-conserving therapy after induction chemotherapy are still unclear. More clinical trials are needed. It has been

Hg(+) Frequency Standards

Science.gov (United States)

Prestage, John D.; Tjoelker, Robert L.; Maleki, Lute

2000-01-01

In this paper we review the development of Hg(+) microwave frequency standards for use in high reliability and continuous operation applications. In recent work we have demonstrated short-term frequency stability of 3 x 10(exp -14)/nu(sub tau) when a cryogenic oscillator of stability 2-3 x 10(exp 15) was used a the local oscillator. The trapped ion frequency standard employs a Hg-202 discharge lamp to optically pump the trapped Hg(+)-199 clock ions and a helium buffer gas to cool the ions to near room temperature. We describe a small Hg(+) ion trap based frequency standard with an extended linear ion trap (LITE) architecture which separates the optical state selection region from the clock resonance region. This separation allows the use of novel trap configurations in the resonance region since no optical pumping is carried out there. A method for measuring the size of an ion cloud inside a linear trap with a 12-rod trap is currently being investigated. At approx. 10(exp -12), the 2nd order Doppler shift for trapped mercury ion frequency standards is one of the largest frequency offsets and its measurement to the 1% level would represent an advance in insuring the very long-term stability of these standards to the 10(exp -14) or better level. Finally, we describe atomic clock comparison experiments that can probe for a time variation of the fine structure constant, alpha = e(exp 2)/2(pi)hc, at the level of 10(exp -20)/year as predicted in some Grand Unified String Theories.

2017 Landsat Science Team Summer Meeting Summary

Science.gov (United States)

Crawford, Christopher J.; Loveland, Thomas R.; Wulder, Michael A.; Irons, James R.

2018-01-01

The summer meeting of the U.S. Geological Survey (USGS)-NASA Landsat Science Team (LST) was held June 11-13, 2017, at the USGS’s Earth Resources Observation and Science (EROS) Center near Sioux Falls, SD. This was the final meeting of the Second (2012-2017) LST.1 Frank Kelly [EROS—Center Director] welcomed the attendees and expressed his thanks to the LST members for their contributions. He then introduced video-recorded messages from South Dakota’s U.S. senators, John Thune and Mike Rounds, in which they acknowledged the efforts of the team in advancing the societal impacts of the Landsat Program.

Numerical simulation of diurnally varying thermal environment in a street canyon under haze-fog conditions

Science.gov (United States)

Tan, Zijing; Dong, Jingliang; Xiao, Yimin; Tu, Jiyuan

2015-10-01

The impact of haze-fog on surface temperature, flow pattern, pollutant dispersion and pedestrian thermal comfort are investigated using computational fluid dynamics (CFD) approach based on a three-dimensional street canyon model under different haze-fog conditions. In this study, light extinction coefficient (Kex) is adopted to represent haze-fog pollution level. Numerical simulations are performed for different Kex values at four representative time events (1000 LST, 1300 LST, 1600 LST and 2000 LST). The numerical results suggest that the surface temperature is strongly affected by the haze-fog condition. Surface heating induced by the solar radiation is enhanced by haze-fog, as higher surface temperature is observed under thicker haze-fog condition. Moreover, the temperature difference between sunlit and shadow surfaces is reduced, while that for the two shadow surfaces is slightly increased. Therefore, the surface temperature among street canyon facets becomes more evenly distributed under heavy haze-fog conditions. In addition, flow patterns are considerably altered by different haze-fog conditions, especially for the afternoon (1600 LST) case, in which thermal-driven flow has opposite direction as that of the wind-driven flow direction. Consequently, pollutants such as vehicular emissions will accumulate at pedestrian level, and pedestrian thermal comfort may lower under thicker haze-fog condition.

Source localization of intermittent rhythmic delta activity in a patient with acute confusional migraine: cross-spectral analysis using standardized low-resolution brain electromagnetic tomography (sLORETA).

Science.gov (United States)

Kim, Dae-Eun; Shin, Jung-Hyun; Kim, Young-Hoon; Eom, Tae-Hoon; Kim, Sung-Hun; Kim, Jung-Min

2016-01-01

Acute confusional migraine (ACM) shows typical electroencephalography (EEG) patterns of diffuse delta slowing and frontal intermittent rhythmic delta activity (FIRDA). The pathophysiology of ACM is still unclear but these patterns suggest neuronal dysfunction in specific brain areas. We performed source localization analysis of IRDA (in the frequency band of 1-3.5 Hz) to better understand the ACM mechanism. Typical IRDA EEG patterns were recorded in a patient with ACM during the acute stage. A second EEG was obtained after recovery from ACM. To identify source localization of IRDA, statistical non-parametric mapping using standardized low-resolution brain electromagnetic tomography was performed for the delta frequency band comparisons between ACM attack and non-attack periods. A difference in the current density maximum was found in the dorsal anterior cingulated cortex (ACC). The significant differences were widely distributed over the frontal, parietal, temporal and limbic lobe, paracentral lobule and insula and were predominant in the left hemisphere. Dorsal ACC dysfunction was demonstrated for the first time in a patient with ACM in this source localization analysis of IRDA. The ACC plays an important role in the frontal attentional control system and acute confusion. This dysfunction of the dorsal ACC might represent an important ACM pathophysiology.

The standard model and beyond

CERN Document Server

Langacker, Paul

2017-01-01

This new edition of The Standard Model and Beyond presents an advanced introduction to the physics and formalism of the standard model and other non-abelian gauge theories. It provides a solid background for understanding supersymmetry, string theory, extra dimensions, dynamical symmetry breaking, and cosmology. In addition to updating all of the experimental and phenomenological results from the first edition, it contains a new chapter on collider physics; expanded discussions of Higgs, neutrino, and dark matter physics; and many new problems. The book first reviews calculational techniques in field theory and the status of quantum electrodynamics. It then focuses on global and local symmetries and the construction of non-abelian gauge theories. The structure and tests of quantum chromodynamics, collider physics, the electroweak interactions and theory, and the physics of neutrino mass and mixing are thoroughly explored. The final chapter discusses the motivations for extending the standard model and examin...

Local area networking handbook

OpenAIRE

O'Hara, Patricia A.

1990-01-01

Approved for public release; distribution is unlimited. This thesis provides Navy shore based commands with sufficient information on local area networking to (1) decide if they need a LAN, (2) determine what their networking requirements are, and (3) select a LAN that satisfies their requirements. LAN topologies, transmission media, and medium access methods are described. In addition, the OSI reference model for computer networking and the IEEE 802 LAN standards are explained in detail. ...

A Combination of TsHARP and Thin Plate Spline Interpolation for Spatial Sharpening of Thermal Imagery

Directory of Open Access Journals (Sweden)

Xuehong Chen

2014-03-01

Full Text Available There have been many studies and much attention paid to spatial sharpening for thermal imagery. Among them, TsHARP, based on the good correlation between vegetation index and land surface temperature (LST, is regarded as a standard technique because of its operational simplicity and effectiveness. However, as LST is affected by other factors (e.g., soil moisture in the areas with low vegetation cover, these areas cannot be well sharpened by TsHARP. Thin plate spline (TPS is another popular downscaling technique for surface data. It has been shown to be accurate and robust for different datasets; however, it has not yet been attempted in thermal sharpening. This paper proposes to combine the TsHARP and TPS methods to enhance the advantages of each. The spatially explicit errors of these two methods were firstly estimated in theory, and then the results of TPS and TsHARP were combined with the estimation of their errors. The experiments performed across various landscapes and data showed that the proposed combined method performs more robustly and accurately than TsHARP.

State and local safety program

Energy Technology Data Exchange (ETDEWEB)

Carlyle Thompson, G D [Utah State Division of Health, Salt Lake City, UT (United States)

1969-07-01

This paper will give emphasis to the need for an increasing role of the states, along with the Federal agencies, in the Plowshare Program in order to assure state and local confidence with respect to the safety of their residents as the Federal government seeks new methods to benefit society. First will be stressed the age-old principle of control at the source. Other factors to be discussed are monitoring; standards and their use; control action; public relations; predictions and the need to have certain advance knowledge of tests - even if security clearance is necessary for appropriate state representatives; the state and local government responsibility to their citizens; the isolation of national decision making from state and local concern and responsibility; cost assessments and their responsibility; and research as it relates to the ecological system as well a the direct short- or long-term effects of radioactivity on man. (author)

State and local safety program

International Nuclear Information System (INIS)

Carlyle Thompson, G.D.

1969-01-01

This paper will give emphasis to the need for an increasing role of the states, along with the Federal agencies, in the Plowshare Program in order to assure state and local confidence with respect to the safety of their residents as the Federal government seeks new methods to benefit society. First will be stressed the age-old principle of control at the source. Other factors to be discussed are monitoring; standards and their use; control action; public relations; predictions and the need to have certain advance knowledge of tests - even if security clearance is necessary for appropriate state representatives; the state and local government responsibility to their citizens; the isolation of national decision making from state and local concern and responsibility; cost assessments and their responsibility; and research as it relates to the ecological system as well a the direct short- or long-term effects of radioactivity on man. (author)

Nearshore waves and longshore sediment transport along Rameshwaram Island off the east coast of India

Directory of Open Access Journals (Sweden)

Rajamanickam Gowthaman

2015-11-01

Full Text Available Wave-induced Longshore Sediment Transport (LST play an important role in the dynamics of the Dhanushkodi sandspit located southeast of Rameshwaram. The LST along the Dhanushkodi coast is studied based on data collected simultaneously in Gulf of Mannar (GoM and Palk Bay (PB using directional waverider buoys. The numerical model REF/DIF1 was used to calculate the nearshore waves and the LST rate was estimated using three different formulae. The model validation was done based on the measured nearshore waves using InterOcean S4DW. Numerical model LITPACK was also used for simulating non-cohesive sediment transport and the LITLINE module was used to study the shoreline evolution over 5 years. Low net annual LST along PB (~0.01 × 106 m3 compared to the GoM region (0.3 × 106 m3 were due to the weak waves. Accretion in the region led to growth of the Dhanushkodi sandspit by 65 m during the period 2010-2015.

Evaluating Vegetation Type Effects on Land Surface Temperature at the City Scale

Science.gov (United States)

Wetherley, E. B.; McFadden, J. P.; Roberts, D. A.

2017-12-01

Understanding the effects of different plant functional types and urban materials on surface temperatures has significant consequences for climate modeling, water management, and human health in cities. To date, doing so at the urban scale has been complicated by small-scale surface heterogeneity and limited data. In this study we examined gradients of land surface temperature (LST) across sub-pixel mixtures of different vegetation types and urban materials across the entire Los Angeles, CA, metropolitan area (4,283 km2). We used AVIRIS airborne hyperspectral imagery (36 m resolution, 224 bands, 0.35 - 2.5 μm) to estimate sub-pixel fractions of impervious, pervious, tree, and turfgrass surfaces, validating them with simulated mixtures constructed from image spectra. We then used simultaneously imaged LST retrievals collected at multiple times of day to examine how temperature changed along gradients of the sub-pixel mixtures. Diurnal in situ LST measurements were used to confirm image values. Sub-pixel fractions were well correlated with simulated validation data for turfgrass (r2 = 0.71), tree (r2 = 0.77), impervious (r2 = 0.77), and pervious (r2 = 0.83) surfaces. The LST of pure pixels showed the effects of both the diurnal cycle and the surface type, with vegetated classes having a smaller diurnal temperature range of 11.6°C whereas non-vegetated classes had a diurnal range of 16.2°C (similar to in situ measurements collected simultaneously with the imagery). Observed LST across fractional gradients of turf/impervious and tree/impervious sub-pixel mixtures decreased linearly with increasing vegetation fraction. The slopes of decreasing LST were significantly different between tree and turf mixtures, with steeper slopes observed for turf (p < 0.05). These results suggest that different physiological characteristics and different access to irrigation water of urban trees and turfgrass results in significantly different LST effects, which can be detected at

Evolution: Its Treatment in K-12 State Science Curriculum Standards

Science.gov (United States)

Lerner, L. S.

2001-12-01

State standards are the basis upon which states and local schools build curricula. Usually taking the form of lists of what students are expected to learn at specified grades or clusters of grades, they influence statewide examinations, textbooks, teacher education and credentialing, and other areas in which states typically exercise control over local curriculum development. State science standards vary very widely in overall quality.1,2 This is especially true in their treatment of evolution, both in the life sciences and to a somewhat lesser extent in geology and astronomy. Not surprisingly, a detailed evaluation of the treatment of evolution in state science standards3 has evoked considerably more public interest than the preceding studies of overall quality. We here consider the following questions: What constitutes a good treatment of evolution in science standards and how does one evaluate the standards? Which states have done well, and which less well? What nonscientific influences have been brought to bear on standards, for what reasons, and by whom? What strategies have been used to obscure or distort the role of evolution as the central organizing principle of the historical sciences? What are the effects of such distortions on students' overall understanding of science? What can the scientific community do to assure the publication of good science standards and to counteract attacks on good science teaching? 1. Lerner, L. S., State Science Standards: An Appraisal of Science Standards in 36 States, The Thomas B. Fordham Foundation, Washington, D.C., March 1998. 2. Lerner, L. S. et al ., The State of State Standards 2000, ibid., January 2000. 3. Lerner, L. S., Good Science, Bad Science: Teaching Evolution In the States, ibid., September 2000.

Adapting standards to the site. Example of Seismic Base Isolation

International Nuclear Information System (INIS)

Viallet, Emmanuel

2014-01-01

Emmanuel Viallet, Civil Design Manager at EDF engineering center SEPTEN, concluded the morning's lectures with a presentation on how to adapt a standard design to site characteristics. He presented the example of the seismic isolation of the Cruas NPP for which the standard 900 MW design was indeed built on 'anti-seismic pads' to withstand local seismic load

Supersymmetric standard model from the heterotic string (II)

International Nuclear Information System (INIS)

Buchmueller, W.; Hamaguchi, K.; Tokyo Univ.; Lebedev, O.; Ratz, M.

2006-06-01

We describe in detail a Z 6 orbifold compactification of the heterotic E 8 x E 8 string which leads to the (supersymmetric) standard model gauge group and matter content. The quarks and leptons appear as three 16-plets of SO(10), two of which are localized at fixed points with local SO(10) symmetry. The model has supersymmetric vacua without exotics at low energies and is consistent with gauge coupling unification. Supersymmetry can be broken via gaugino condensation in the hidden sector. The model has large vacuum degeneracy. Certain vacua with approximate B-L symmetry have attractive phenomenological features. The top quark Yukawa coupling arises from gauge interactions and is of the order of the gauge couplings. The other Yukawa couplings are suppressed by powers of standard model singlet fields, similarly to the Froggatt-Nielsen mechanism. (Orig.)

On locality of Generalized Reed-Muller codes over the broadcast erasure channel

KAUST Repository

Alloum, Amira

2016-07-28

One to Many communications are expected to be among the killer applications for the currently discussed 5G standard. The usage of coding mechanisms is impacting broadcasting standard quality, as coding is involved at several levels of the stack, and more specifically at the application layer where Rateless, LDPC, Reed Slomon codes and network coding schemes have been extensively studied, optimized and standardized in the past. Beyond reusing, extending or adapting existing application layer packet coding mechanisms based on previous schemes and designed for the foregoing LTE or other broadcasting standards; our purpose is to investigate the use of Generalized Reed Muller codes and the value of their locality property in their progressive decoding for Broadcast/Multicast communication schemes with real time video delivery. Our results are meant to bring insight into the use of locally decodable codes in Broadcasting. © 2016 IEEE.

Food Standards are Good – for Middle-Class Farmers

DEFF Research Database (Denmark)

Hansen, Henrik; Trifkovic, Neda

2014-01-01

We estimate the causal effect of food standards on Vietnamese pangasius farmers’ wellbeing measured by per capita consumption expenditure. We estimate both the average effects and the local average treatment effects on poorer and richer farmers by instrumental variable quantile regression. Our...... results indicate that large returns can be accrued from food standards, but only for the upper middle-class farmers, i.e., those between the 50% and 85% quantiles of the expenditure distribution. Overall, our result points to an exclusionary impact of standards for the poorest farmers while the richest do...

Peer Evaluation Can Reliably Measure Local Knowledge

Science.gov (United States)

Reyes-García, Victoria; Díaz-Reviriego, Isabel; Duda, Romain; Fernández-Llamazares, Álvaro; Gallois, Sandrine; Guèze, Maximilien; Napitupulu, Lucentezza; Pyhälä, Aili

2016-01-01

We assess the consistency of measures of individual local ecological knowledge obtained through peer evaluation against three standard measures: identification tasks, structured questionnaires, and self-reported skills questionnaires. We collected ethnographic information among the Baka (Congo), the Punan (Borneo), and the Tsimane' (Amazon) to…

Characterising fire hazard from temporal sequences of thermal infrared modis measurements

NARCIS (Netherlands)

Maffei, C.; Alfieri, S.M.; Menenti, M.

2012-01-01

The objective of the present research was the characterisation of fire hazard using temporal sequences of land surface temperature (LST) derived from Terra-MODIS measurements. The investigation was based on a complete sequence of MODIS LST data from 2000 to 2006 on Campania (Italy) and on a dataset

Journal of Earth System Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Land surface temperature (LST) is a key parameter in environment and earth science study, especially for monitoring drought. The objective of this work is a comparison of two split-window methods: Mao method and Sobrino method, for retrieving LST using MODIS (Moderate-resolution Imaging Spectroradiometer) data in ...

Feasibility study on analogue cancellation of local interference in multimode transceivers

NARCIS (Netherlands)

Habibi, H.; Zamanifekri, A.; Janssen, E.J.G.; Wu, Y.; Baltus, P.G.M.; Bergmans, J.W.M.

2014-01-01

In multimode transceivers, the transmitter for one communication standard induces a strong local interference in the receiver for another standard. Such strong interference can severely affect the receiver, if it is not suppressed at an early stage of the receiver. A widely explored method to cancel

Multivariate localization methods for ensemble Kalman filtering

KAUST Repository

Roh, S.

2015-12-03

In ensemble Kalman filtering (EnKF), the small number of ensemble members that is feasible to use in a practical data assimilation application leads to sampling variability of the estimates of the background error covariances. The standard approach to reducing the effects of this sampling variability, which has also been found to be highly efficient in improving the performance of EnKF, is the localization of the estimates of the covariances. One family of localization techniques is based on taking the Schur (element-wise) product of the ensemble-based sample covariance matrix and a correlation matrix whose entries are obtained by the discretization of a distance-dependent correlation function. While the proper definition of the localization function for a single state variable has been extensively investigated, a rigorous definition of the localization function for multiple state variables that exist at the same locations has been seldom considered. This paper introduces two strategies for the construction of localization functions for multiple state variables. The proposed localization functions are tested by assimilating simulated observations experiments into the bivariate Lorenz 95 model with their help.

Multivariate localization methods for ensemble Kalman filtering

KAUST Repository

Roh, S.

2015-05-08

In ensemble Kalman filtering (EnKF), the small number of ensemble members that is feasible to use in a practical data assimilation application leads to sampling variability of the estimates of the background error covariances. The standard approach to reducing the effects of this sampling variability, which has also been found to be highly efficient in improving the performance of EnKF, is the localization of the estimates of the covariances. One family of localization techniques is based on taking the Schur (entry-wise) product of the ensemble-based sample covariance matrix and a correlation matrix whose entries are obtained by the discretization of a distance-dependent correlation function. While the proper definition of the localization function for a single state variable has been extensively investigated, a rigorous definition of the localization function for multiple state variables has been seldom considered. This paper introduces two strategies for the construction of localization functions for multiple state variables. The proposed localization functions are tested by assimilating simulated observations experiments into the bivariate Lorenz 95 model with their help.

Multivariate localization methods for ensemble Kalman filtering

KAUST Repository

Roh, S.; Jun, M.; Szunyogh, I.; Genton, Marc G.

2015-01-01

In ensemble Kalman filtering (EnKF), the small number of ensemble members that is feasible to use in a practical data assimilation application leads to sampling variability of the estimates of the background error covariances. The standard approach to reducing the effects of this sampling variability, which has also been found to be highly efficient in improving the performance of EnKF, is the localization of the estimates of the covariances. One family of localization techniques is based on taking the Schur (entry-wise) product of the ensemble-based sample covariance matrix and a correlation matrix whose entries are obtained by the discretization of a distance-dependent correlation function. While the proper definition of the localization function for a single state variable has been extensively investigated, a rigorous definition of the localization function for multiple state variables has been seldom considered. This paper introduces two strategies for the construction of localization functions for multiple state variables. The proposed localization functions are tested by assimilating simulated observations experiments into the bivariate Lorenz 95 model with their help.

Multivariate localization methods for ensemble Kalman filtering

Science.gov (United States)

Roh, S.; Jun, M.; Szunyogh, I.; Genton, M. G.

2015-12-01

In ensemble Kalman filtering (EnKF), the small number of ensemble members that is feasible to use in a practical data assimilation application leads to sampling variability of the estimates of the background error covariances. The standard approach to reducing the effects of this sampling variability, which has also been found to be highly efficient in improving the performance of EnKF, is the localization of the estimates of the covariances. One family of localization techniques is based on taking the Schur (element-wise) product of the ensemble-based sample covariance matrix and a correlation matrix whose entries are obtained by the discretization of a distance-dependent correlation function. While the proper definition of the localization function for a single state variable has been extensively investigated, a rigorous definition of the localization function for multiple state variables that exist at the same locations has been seldom considered. This paper introduces two strategies for the construction of localization functions for multiple state variables. The proposed localization functions are tested by assimilating simulated observations experiments into the bivariate Lorenz 95 model with their help.

The power of local action in occupational health: the adoption of local exhaust ventilation in the Chicago tuckpointing trade.

Science.gov (United States)

Weinstein, Marc; Susi, Pam; Goldberg, Mark

2016-04-01

Silica is a pervasive and potentially deadly occupational hazard in construction. The occupational risk posed by silica has long been known, but efforts to use engineering controls to minimize dust generation in tuckpointing operations, a masonry restoration specialty, have been slow. The objective of this study is to explore how local innovation in occupational safety and health may emerge, absent the establishment of national standards. This study uses a case study to explore the adoption of local exhaust ventilation in tuckpointing operations in the Chicago area. Sources of data for this research include interviews with a diverse range of key informants and the review of archival material. This case study found local unions, municipal regulators, contractors, and major public users of construction services played a central role in the events and milestones that led to the early adoption of local exhaust ventilation in Chicago. The adoption of local exhaust ventilation technology in Chicago demonstrates the potential for local actors to fill an important void when rulemaking in vital areas of occupational of health impedes effective national regulation.

Urban percent impervious surface and its relationship with land surface temperature in Yantai City, China

International Nuclear Information System (INIS)

Yu, Xinyang; Lu, Changhe

2014-01-01

This study investigated percent impervious surface area (PISA) extracted by a four-endmember normalized spectral mixture analysis (NSMA) method and evaluated the reliability of PISA as an indicator of land surface temperature (LST). Landsat Thematic Mapper (TM) and Enhanced Thematic Mapper Plus (ETM+) images for Yantai city, eastern China obtained from USGS were used as the main data source. The results demonstrated that four-endmember NSMA method performed better than the typical three-endmember one, and there was a strong linear relationship between LST and PISA for the two images, which suggest percent impervious surface area provides an alternative parameter for analyzing LST quantitatively in urban areas

Tribological Behavior of Oil-Lubricated Laser Textured Steel Surfaces in Conformal Flat and Non-Conformal Contacts

Energy Technology Data Exchange (ETDEWEB)

Kovalchenko, A. M. [Inst. for Problems of Materials Science, Dept. 7, 3 Krzhizhanovsky Street, Kyiv 03142, UA (Corresponding author), e-mail: andrii.kovalchenko@gatech.edu; Erdemir, A. [Argonne National Lab., Energy Systems Division, 9700 South Cass Avenue, Argonne, IL 60439 US; Ajayi, O. O. [Argonne National Lab., Energy Systems Division, 9700 South Cass Avenue, Argonne, IL 60439 US; Etsion, I. [Technion-Israel Inst. of Technology, Dept. of Mechanical Engineering, Haifa 32000, IL

2017-01-30

Changing the surface texture of sliding surfaces is an effective way to manipulate friction and wear of lubricated surfaces. Having realized its potential, we have done very extensive studies on the effects of laser surface texturing (LST, which involves the creation of an array of microdimples on a surface) on friction and wear behavior of oil-lubricated steel surfaces in the early 2000s. In this paper, we reviewed some of our research accomplishments and assessed future directions of the laser texturing field in many diverse industrial applications. Our studies specifically addressed the impact of laser texturing on friction and wear of both the flat conformal and initial non-conformal point contact configurations using a pin-on-disk test rig under fully-flooded synthetic oil lubricants with different viscosities. Electrical resistance measurement between pin and LST disks was also used to determine the operating lubrication regimes in relation to friction. In conformal contact, we confirmed that LST could significantly expand the operating conditions for hydrodynamic lubrication to significantly much higher loads and slower speeds. In particular, with LST and higher viscosity oils, the low-friction full hydrodynamic regime was shifted to the far left in the Stribeck diagram. Overall, the beneficial effects of laser surface texturing were more pronounced at higher speeds and loads and with higher viscosity oil. LST was also observed to reduce the magnitude of friction coefficients in the boundary regime. For the non-conformal contact configuration, we determined that LST would produce more abrasive wear on the rubbing counterface compared to the untreated surfaces due to a reduction in lubricant fluid film thickness, as well as the highly uneven and rough nature of the textured surfaces. However, this higher initial wear rate has led to faster generation of a conformal contact, and thus transition from the high-friction boundary to lower friction mixed

25 CFR 170.810 - To what standards must an IRR transportation facility be maintained?

Science.gov (United States)

2010-04-01

... WATER INDIAN RESERVATION ROADS PROGRAM BIA Road Maintenance § 170.810 To what standards must an IRR... standards; (b) AASHTO road and bridge maintenance manuals, latest edition; or (c) Other applicable Federal, State, tribal, or local government maintenance standards as may be negotiated in an ISDEAA road...

Life Skills Training: Preventing Substance Misuse by Enhancing Individual and Social Competence

Science.gov (United States)

Botvin, Gilbert J.; Griffin, Kenneth W.

2014-01-01

Research concerning the etiology and prevention of substance misuse has led to the development of preventive interventions that are theory-based and effective. One such approach, Life Skills Training (LST), targets key etiologic factors using a conceptual framework derived from social learning theory and problem behavior theory. LST has been…

77 FR 42367 - National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing...

Science.gov (United States)

2012-07-18

... and 63 National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing... Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry and Standards of... manufacturing plants. Federal government Not affected. State/local/tribal government.... Portland cement...

Local field theory on κ-Minkowski space, star products and noncommutative translations

International Nuclear Information System (INIS)

Kosinski, P.; Maslanka, P.; Lukierski, J.

2000-01-01

We consider local field theory on κ-deformed Minkowski space which is an example of solvable Lie-algebraic noncommutative structure. Using integration formula over κ-Minkowski space and κ-deformed Fourier transform, we consider for deformed local fields the reality conditions as well as deformation of action functionals in standard Minkowski space. We present explicit formulas for two equivalent star products describing CBH quantization of field theory on κ-Minkowski space. We express also via star product technique the noncommutative translations in κ-Minkowski space by commutative translations in standard Minkowski space. (author)

The Development of the Standard Lithuanian Language: Ecolinguistic Approach

Directory of Open Access Journals (Sweden)

Vaida Buivydienė

2014-06-01

Full Text Available The theory of standard languages is closely linked with the standardization policy and prevailing ideology. The language ideology comprises its value, experience and convictions related to language usage and its dis - course being influenced at institutional, local and global levels. Recently, in the last decades, foreign linguists have linked the theories of the development of standard lan- guages and their ideologies with an ecolinguistic approach towards language standardization phenomena. The article is based on Einar Haugen ’s theory about the development of standard languages and ecolinguistic statements and presents the stages of developing the standard language as well as the factors having an influ - ence on them. In conclusion, a strong political and social impact has been made on the development of the standard Lithuanian language. The stages of the progress of the standard Lithuanian language have rapidly changed each other, some have been held very close to one another and some still have been taken part.

Dynamic analysis and ecological evaluation of urban heat islands in Raipur city, India

Science.gov (United States)

Guha, Subhanil; Govil, Himanshu; Mukherjee, Sandip

2017-07-01

Spatial-temporal distribution of the urban heat islands (UHI) and their changes over Raipur city have been analyzed using multitemporal Landsat satellite data from 1995 to 2016. Land surface temperature (LST) was retrieved through a mono-window algorithm. Some selected land use/land cover (LU-LC) indices were analyzed with LST using linear regression. The urban thermal field variance index (UTFVI) was applied to measure the thermal comfort level of the city. Results show that during the observed period, the study area experienced a gradual increasing rate in mean LST (>1% per annum). The UHI developed especially along the north-western industrial area and south-eastern bare land of the city. A difference in mean LST between UHI and non-UHI for different time periods (2.6°C in 1995, 2.85°C in 2006, 3.42°C in 2009, and 3.63°C in 2016) reflects the continuous warming status of the city. The LST map also shows the existence of a few urban hot spots near the industrial areas, metal roofs, and high density transport parking lots, which are more abundant in the north-western part of the city. The UTFVI map associated with UHI indicates that the inner parts of the city are ecologically more comfortable than the outer peripheries.

ANALYSING THE EFFECTS OF DIFFERENT LAND COVER TYPES ON LAND SURFACE TEMPERATURE USING SATELLITE DATA

Directory of Open Access Journals (Sweden)

A. Şekertekin

2015-12-01

Full Text Available Monitoring Land Surface Temperature (LST via remote sensing images is one of the most important contributions to climatology. LST is an important parameter governing the energy balance on the Earth and it also helps us to understand the behavior of urban heat islands. There are lots of algorithms to obtain LST by remote sensing techniques. The most commonly used algorithms are split-window algorithm, temperature/emissivity separation method, mono-window algorithm and single channel method. In this research, mono window algorithm was implemented to Landsat 5 TM image acquired on 28.08.2011. Besides, meteorological data such as humidity and temperature are used in the algorithm. Moreover, high resolution Geoeye-1 and Worldview-2 images acquired on 29.08.2011 and 12.07.2013 respectively were used to investigate the relationships between LST and land cover type. As a result of the analyses, area with vegetation cover has approximately 5 ºC lower temperatures than the city center and arid land., LST values change about 10 ºC in the city center because of different surface properties such as reinforced concrete construction, green zones and sandbank. The temperature around some places in thermal power plant region (ÇATES and ZETES Çatalağzı, is about 5 ºC higher than city center. Sandbank and agricultural areas have highest temperature due to the land cover structure.

Analysing the Effects of Different Land Cover Types on Land Surface Temperature Using Satellite Data

Science.gov (United States)

Şekertekin, A.; Kutoglu, Ş. H.; Kaya, S.; Marangoz, A. M.

2015-12-01

Monitoring Land Surface Temperature (LST) via remote sensing images is one of the most important contributions to climatology. LST is an important parameter governing the energy balance on the Earth and it also helps us to understand the behavior of urban heat islands. There are lots of algorithms to obtain LST by remote sensing techniques. The most commonly used algorithms are split-window algorithm, temperature/emissivity separation method, mono-window algorithm and single channel method. In this research, mono window algorithm was implemented to Landsat 5 TM image acquired on 28.08.2011. Besides, meteorological data such as humidity and temperature are used in the algorithm. Moreover, high resolution Geoeye-1 and Worldview-2 images acquired on 29.08.2011 and 12.07.2013 respectively were used to investigate the relationships between LST and land cover type. As a result of the analyses, area with vegetation cover has approximately 5 ºC lower temperatures than the city center and arid land., LST values change about 10 ºC in the city center because of different surface properties such as reinforced concrete construction, green zones and sandbank. The temperature around some places in thermal power plant region (ÇATES and ZETES) Çatalağzı, is about 5 ºC higher than city center. Sandbank and agricultural areas have highest temperature due to the land cover structure.

Accounting standards for small and medium-sized entities. Evidence from Spain

OpenAIRE

Milanés Montero Patricia; Albarrán Lozano Irene; Texeira Quirós Joaquín; Esteban Pérez Calderón

2011-01-01

By approving Regulation 1606/2002, the European Commission entrusts the local European Union regulators with the difficult decision as to whether making the International Accounting Standards (IAS/IFRS) extensive for their Small and Medium sized Entities or not. International Financial Reporting Standard for Small and Medium-sizzed Entities (hereinafter IFRS for SMEs) was published in 2009, and the European Commission had also decided to seek the opinion of EU stakeholders on this Standard. W...

Effectiveness of a locally produced RUTF for the treatment of Acute Malnutrition in Vietnam

International Nuclear Information System (INIS)

Nguyen, Marie; Berger, Jacques; Wieringa, Frank; Tran, Thuy Nga; Do, Thi Bao Hoa; Nguyen, Hong Minh; Mathisen, Roger

2014-01-01

Full text: Background and Objectives: After an assessment of peanut-based RUTF in Cambodia found low acceptability rates, the National Institute of Nutrition Vietnam, UNICEF and the Institut de Recherche pour le Développement started in 2009 to work on a locally produced RUTF, adapted to local taste and preference for the treatment of severe acute malnutrition (SAM). In 2010, the newly developed product was found to be highly acceptable, but impact on weight gain needed to be proven. Therefore, this study was conducted to assess the effectiveness of the local RUTF on weight gain and recovery rate using the RUTF in a home based treatment of acute malnutrition. Methods and Design: The study was a randomized intervention trial in 150 children, aged 6-59 months, with SAM or moderate acute malnutrition (MAM) to test the effectiveness of the local RUTF (bar) against a standard RUTF (peanut-based paste). The study was done as a community-based intervention trial in Kon Tum province (Central Highlands region), Vietnam, where an Integrated Management of Acute Malnutrition programs (IMAM) program was just being introduced. Results: Children consumed 92% and 70% of the offered local RUTF and standard RUTF respectively, underlining the problems with a peanut-based RUTF in SE Asia. Nutritional status of the children was significantly improved after the 8 weeks intervention. Mean weight gain with the standard RUTF and the local RUTF was 2.97 (± 1.57) g/kg/d and 2.52 (± 1.23) g/kg/d respectively. Also, both RUTFs improved significantly height and HAZ-scores, with a mean height gain of 22.4 (±18.7) mm and 32.3 (±36.3) mm for respectively standard and local RUTF. The recovery rate from acute malnutrition with RUTFs as home treatment was 70.8%, and not different between the 2 interventions. Conclusions: The local RUTF was as effective as the standard RUTF on the treatment of acute malnutrition, whereas acceptability was higher. The local RUTF can be successfully used in the

Comparison of pituitary and recombinant human thyrotropin standards in an immunoradiometric system

International Nuclear Information System (INIS)

Blanca Fernandez, Silvia; Rodriguez Gonzalez, Julio Cesar; Nisembaum Alas, Amaparo; Sevy Gonzalez, O.

1998-01-01

Results of two standards of human thyrotropin of pituitaries (B) and recombinant (C) origen supplied by the Instituto of pesquisas Energeticas y Nucleares, Brazil, were compared in our immunoradiometric reference system that use an human thyrotropin pituitary standard of local production (A). This work was supported by the International Atomic Energy Agency for an inter-regional comparison and set up of a reference standard

The relationship between typhoons' peripheral circulation and ground-level ozone concentrations in central Taiwan.

Science.gov (United States)

Cheng, Wan-Li; Lai, Li-Wei; Den, Walter; Wu, Meng-Ting; Hsueh, Chao-An; Lin, Pay-Liam; Pai, Chueh-Ling; Yan, Yeou-Lih

2014-02-01

Surface data of meteorological parameters (wind speed, wind direction, and mixing height) and air pollutant concentrations (O3, NO, and NO2) were collected for a 92-day period associated with typhoon formation in 2005. The influence of typhoons on O3 concentration were defined by azimuth and distance from Taiwan, and Types A, B, and C correspond to typhoons less than 1,500 km from Taiwan and located between azimuths 45° and 135°, 135° and 225°, and 225° and 45°, respectively. Type D corresponds to typhoons more than 1,500 km from Taiwan. Titration reactions were conducted at three temporal phases: 2000-0700, 0800-1100, and 1200-1400 LST (Local Standard Time). The air pollution model (TAPM) was used to simulate wind fields and trajectories of air masses. It was determined that typhoon position affected O3 concentration, temporal and spatial patterns of O3 titration and vertical meteorological characteristics, which were not all at the statistically significant level.

Sensitivity of Landsat 8 Surface Temperature Estimates to Atmospheric Profile Data: A Study Using MODTRAN in Dryland Irrigated Systems

KAUST Repository

Rosas, Jorge; Houborg, Rasmus; McCabe, Matthew

2017-01-01

The land surface temperature (LST) represents a critical element in efforts to characterize global surface energy and water fluxes, as well as being an essential climate variable in its own right. Current satellite platforms provide a range of spatial and temporal resolution radiance data from which LST can be determined. One of the most complete records of data comes via the Landsat series of satellites, which provide a continuous sequence that extends back to 1982. However, for much of this time, Landsat thermal data were provided through a single broadband thermal channel, making surface temperature retrieval challenging. To fully exploit the valuable time-series of thermal information that is available from these satellites requires efforts to better describe and understand the accuracy of temperature retrievals. Here, we contribute to these efforts by examining the impact of atmospheric correction on the estimation of LST, using atmospheric profiles derived from a range of in-situ, reanalysis, and satellite data. Radiance data from the thermal infrared (TIR) sensor onboard Landsat 8 was converted to LST by using the MODTRAN version 5.2 radiative transfer model, allowing the production of an LST time series based upon 28 Landsat overpasses. LST retrievals were then evaluated against in-situ thermal measurements collected over an arid zone farmland comprising both bare soil and vegetated surface types. Atmospheric profiles derived from AIRS, MOD07, ECMWF, NCEP, and balloon-based radiosonde data were used to drive the MODTRAN simulations. In addition to examining the direct impact of using various profile data on LST retrievals, randomly distributed errors were introduced into a range of forcing variables to better understand retrieval uncertainty. Results indicated differences in LST of up to 1 K for perturbations in emissivity and profile measurements, with the analysis also highlighting the challenges in modeling aerosol optical depth (AOD) over arid lands and

Sensitivity of Landsat 8 Surface Temperature Estimates to Atmospheric Profile Data: A Study Using MODTRAN in Dryland Irrigated Systems

KAUST Repository

Rosas, Jorge

2017-09-26

The land surface temperature (LST) represents a critical element in efforts to characterize global surface energy and water fluxes, as well as being an essential climate variable in its own right. Current satellite platforms provide a range of spatial and temporal resolution radiance data from which LST can be determined. One of the most complete records of data comes via the Landsat series of satellites, which provide a continuous sequence that extends back to 1982. However, for much of this time, Landsat thermal data were provided through a single broadband thermal channel, making surface temperature retrieval challenging. To fully exploit the valuable time-series of thermal information that is available from these satellites requires efforts to better describe and understand the accuracy of temperature retrievals. Here, we contribute to these efforts by examining the impact of atmospheric correction on the estimation of LST, using atmospheric profiles derived from a range of in-situ, reanalysis, and satellite data. Radiance data from the thermal infrared (TIR) sensor onboard Landsat 8 was converted to LST by using the MODTRAN version 5.2 radiative transfer model, allowing the production of an LST time series based upon 28 Landsat overpasses. LST retrievals were then evaluated against in-situ thermal measurements collected over an arid zone farmland comprising both bare soil and vegetated surface types. Atmospheric profiles derived from AIRS, MOD07, ECMWF, NCEP, and balloon-based radiosonde data were used to drive the MODTRAN simulations. In addition to examining the direct impact of using various profile data on LST retrievals, randomly distributed errors were introduced into a range of forcing variables to better understand retrieval uncertainty. Results indicated differences in LST of up to 1 K for perturbations in emissivity and profile measurements, with the analysis also highlighting the challenges in modeling aerosol optical depth (AOD) over arid lands and

Local grand unification and string theory

International Nuclear Information System (INIS)

Nilles, Hans Peter; Vaudrevange, Patrick K.S.

2009-09-01

The low energy effective action of string theory depends strongly on the process of compactification and the localization of fields in extra dimensions. Explicit string constructions towards the minimal supersymmetric standard model (MSSM) reveal interesting results leading to the concept of local grand unification. Properties of the MSSM indicate that we might live at a special location close to an orbifold fixed point rather than a generic point in Calabi-Yau moduli space. We observe an enhancement of (discrete) symmetries that have various implications for the properties of the MSSM such as proton stability as well as solutions to the flavor problem, the m-problem and the strong CP-problem. (orig.)

Bicalutamide as immediate therapy either alone or as adjuvant to standard care of patients with localized or locally advanced prostate cancer: first analysis of the early prostate cancer program

DEFF Research Database (Denmark)

See, William A; Wirth, Manfred P; McLeod, David G

2002-01-01

We determine the efficacy and tolerability of bicalutamide as immediate therapy, either alone or as adjuvant to treatment of curative intent, in patients with clinically localized or locally advanced prostate cancer.......We determine the efficacy and tolerability of bicalutamide as immediate therapy, either alone or as adjuvant to treatment of curative intent, in patients with clinically localized or locally advanced prostate cancer....

Tibiofemoral wear in standard and non-standard squat: implication for total knee arthroplasty.

Science.gov (United States)

Fekete, Gusztáv; Sun, Dong; Gu, Yaodong; Neis, Patric Daniel; Ferreira, Ney Francisco; Innocenti, Bernardo; Csizmadia, Béla M

2017-01-01

Due to the more resilient biomaterials, problems related to wear in total knee replacements (TKRs) have decreased but not disappeared. In the design-related factors, wear is still the second most important mechanical factor that limits the lifetime of TKRs and it is also highly influenced by the local kinematics of the knee. During wear experiments, constant load and slide-roll ratio is frequently applied in tribo-tests beside other important parameters. Nevertheless, numerous studies demonstrated that constant slide-roll ratio is not accurate approach if TKR wear is modelled, while instead of a constant load, a flexion-angle dependent tibiofemoral force should be involved into the wear model to obtain realistic results. A new analytical wear model, based upon Archard's law, is introduced, which can determine the effect of the tibiofemoral force and the varying slide-roll on wear between the tibiofemoral connection under standard and non-standard squat movement. The calculated total wear with constant slide-roll during standard squat was 5.5 times higher compared to the reference value, while if total wear includes varying slide-roll during standard squat, the calculated wear was approximately 6.25 times higher. With regard to non-standard squat, total wear with constant slide-roll during standard squat was 4.16 times higher than the reference value. If total wear included varying slide-roll, the calculated wear was approximately 4.75 times higher. It was demonstrated that the augmented force parameter solely caused 65% higher wear volume while the slide-roll ratio itself increased wear volume by 15% higher compared to the reference value. These results state that the force component has the major effect on wear propagation while non-standard squat should be proposed for TKR patients as rehabilitation exercise.

Local air quality management: some evidence of current practices

Energy Technology Data Exchange (ETDEWEB)

Beattie, Clare; Newton, Alex; Longhurst, Jim [University of the West of England, Air Quality Research Group, Bristol (United Kingdom)

1998-12-01

The recent legislative changes, notably the Environment Act 1995 and resultant National Air Quality Strategy have brought new powers and obligations to local authorities to reach specified air quality standards and objectives. Initially this will involve local authorities carrying out a review and assessment of air quality in their locality by December 1999. This paper will outline a project currently being undertaken within the University of the West of England investigating how this legislation is being put into practice and present the results from a nation-wide questionnaire survey of environmental health officers. The study found that local authorities are still at an early stage of the process. It seems probable that one possible barrier to the implementation of Air Quality Management will be communication and cooperation within local authorities. (Author)

Sensitivity of some local isolates of Mycoplasma gallisepticum against antibiotics

Directory of Open Access Journals (Sweden)

Sutiastuti Wahyuwardani

1998-03-01

Full Text Available Sensitivity of five local isolates ofMycoplasma gallisepticum (MG strain and two standard MG isolates obtained from Australia were tested against antibiotics of oxytetracycline, doxycycline, erythromycin, bacitracin, vancomycin, methicillin and penicillin using antibiogram disc method. The result showed that one, 2 and 3 local MG isolates were resistent to doxycycline, erythromycin and oxytetracycline respectively . MG isolate of ADA7 from Australia was found to be resistent to all antibiotics tested. None ofthe local MG isolates were sensitive against bacitracin, vancomycin, methicillin and penicillin.

Comparison of local International Sensitivity Index calibration and 'Direct INR' methods in correction of locally reported International Normalized Ratios: an international study. On behalf of the European Action of Anticoagulation

DEFF Research Database (Denmark)

Poller, L; Keown, M; Ibrahim, S

2007-01-01

collaborative study at 77 centers has compared local INR correction using the two alternative methods recommended in the Scientific and Standardization Committee of the International Society on Thrombosis and Haemostasis guidelines: local ISI calibration and 'Direct INR'. METHODS: Success of INR correction...

Producing the Docile Body: Analysing Local Area Under-Performance Inspection (LAUI)

Science.gov (United States)

Clapham, Andrew

2015-01-01

Sir Michael Wilshaw, the head of the Office for Standards in Education (OfSTED), declared a "new wave" of Local Area Under-performance Inspections (LAUI) of schools "denying children the standard of education they deserve". This paper examines how the threat of LAUI played out over three mathematics lessons taught by a teacher…

Land surface temperature as an indicator of the unsaturated zone thickness: A remote sensing approach in the Atacama Desert.

Science.gov (United States)

Urqueta, Harry; Jódar, Jorge; Herrera, Christian; Wilke, Hans-G; Medina, Agustín; Urrutia, Javier; Custodio, Emilio; Rodríguez, Jazna

2018-01-15

Land surface temperature (LST) seems to be related to the temperature of shallow aquifers and the unsaturated zone thickness (∆Z uz ). That relationship is valid when the study area fulfils certain characteristics: a) there should be no downward moisture fluxes in an unsaturated zone, b) the soil composition in terms of both, the different horizon materials and their corresponding thermal and hydraulic properties, must be as homogeneous and isotropic as possible, c) flat and regular topography, and d) steady state groundwater temperature with a spatially homogeneous temperature distribution. A night time Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) image and temperature field measurements are used to test the validity of the relationship between LST and ∆Z uz at the Pampa del Tamarugal, which is located in the Atacama Desert (Chile) and meets the above required conditions. The results indicate that there is a relation between the land surface temperature and the unsaturated zone thickness in the study area. Moreover, the field measurements of soil temperature indicate that shallow aquifers dampen both the daily and the seasonal amplitude of the temperature oscillation generated by the local climate conditions. Despite empirically observing the relationship between the LST and ∆Z uz in the study zone, such a relationship cannot be applied to directly estimate ∆Z uz using temperatures from nighttime thermal satellite images. To this end, it is necessary to consider the soil thermal properties, the soil surface roughness and the unseen water and moisture fluxes (e.g., capillarity and evaporation) that typically occur in the subsurface. Copyright © 2017 Elsevier B.V. All rights reserved.

Building climate change into infrastructure codes and standards

International Nuclear Information System (INIS)

Auld, H.; Klaasen, J.; Morris, R.; Fernandez, S.; MacIver, D.; Bernstein, D.

2009-01-01

'Full text:' Building codes and standards and the climatic design values embedded within these legal to semi-legal documents have profound safety, health and economic implications for Canada's infrastructure systems. The climatic design values that have been used for the design of almost all of today's more than $5.5 Trillion in infrastructure are based on historical climate data and assume that the extremes of the past will represent future conditions. Since new infrastructure based on codes and standards will be built to survive for decades to come, it is critically important that existing climatic design information be as accurate and up-to-date as possible, that the changing climate be monitored to detect and highlight vulnerabilities of existing infrastructure, that forensic studies of climate-related failures be undertaken and that codes and standards processes incorporate future climates and extremes as much as possible. Uncertainties in the current climate change models and their scenarios currently challenge our ability to project future extremes regionally and locally. Improvements to the spatial and temporal resolution of these climate change scenarios, along with improved methodologies to treat model biases and localize results, will allow future codes and standards to better reflect the extremes and weathering conditions expected over the lifespan of structures. In the meantime, other information and code processes can be used to incorporate changing climate conditions into upcoming infrastructure codes and standards, to “bridge” the model uncertainty gap and to complement the state of existing projections. This presentation will outline some of the varied information and processes that will be used to incorporate climate change adaptation into the next development cycle of the National Building Code of Canada and numerous other national CSA infrastructure standards. (author)

Direct numerical simulations of mack-mode damping on porous coated cones

Science.gov (United States)

Lüdeke, H.; Wartemann, V.

2013-06-01

The flow field over a 3 degree blunt cone is investigated with respect to a hypersonic stability analysis of the boundary-layer flow at Mach 6 with porous as well as smooth walls by comparing local direct numerical simulations (DNS) and linear stability theory (LST) data. The original boundary-layer profile is generated by a finite volume solver, using shock capturing techniques to generate an axisymmetric flow field. Local boundary-layer profiles are extracted from this flow field and hypersonic Mack-modes are superimposed for cone-walls with and without a porous surface used as a passive transition-reduction device. Special care is taken of curvature effects of the wall on the mode development over smooth and porous walls.

Application of La-Doped SrTiO3 in Advanced Metal-Supported Solid Oxide Fuel Cells

Directory of Open Access Journals (Sweden)

Sabrina Presto

2018-03-01

Full Text Available Composite materials frequently allow the drawbacks of single components to be overcome thanks to a synergistic combination of material- and structure-specific features, leading to enhanced and also new properties. This is the case of a metallic-ceramic composite, a nickel-chromium-aluminum (NiCrAl foam impregnated with La-doped Strontium Titanate (LST. This particular cermet has very interesting properties that can be used in different fields of application, namely: mechanical robustness provided by the metal foam; and chemical stability in harsh conditions of temperature and atmosphere by promotion of a thin protective layer of alumina (Al2O3; high electronic conductivity given by a percolating ceramic conducting phase, i.e., La-doped Strontium Titanate. In this paper, its application as a current collector in a metal-supported Solid Oxide Fuel Cells (SOFC was studied. Firstly, the electronic properties of different compositions, stoichiometric and under stoichiometric, of LST were analyzed to choose the best one in terms of conductivity and phase purity. Then, LST chemical stability was studied in the presence of Al2O3 at different temperatures, gas compositions and aging times. Finally, stability and conductivity of LST-impregnated NiCrAl foam composite materials were measured, and LST was found to be fully compatible with the NiCrAl foam, as no reactions were detected in oxidizing and reducing atmosphere after up to 300 h operation at 750 °C and 900 °C between the Al2O3 layer and LST. Results showed that the composite is suitable as a current collector in innovative designs of metal-supported SOFC, like the Evolve cell, in which the metallic part is supposed not only to provide the structural stability to the cell, but also to play the role of current collector due to the impregnation of ceramic material.

LAND SURFACE TEMPERATURES ESTIMATED ON GROUNDOBSERVED DATA AND SATELLITE IMAGES, DURING THE VEGETATION PERIOD IN THE OLTENIA PLAIN

Directory of Open Access Journals (Sweden)

ONŢEL IRINA

2015-03-01

Full Text Available The purpose of this study is to analyze the land surface temperatures by using climatological and remote sensing data during the vegetation period in the Oltenia Plain. The data used in this study refer both to climatological data (namely monthly and seasonal air and soil temperatures, and to remote sensing data delivered by MODIS Land Surface Temperature (LST, with a spatial resolution of 1 km. The analyzed period spans from 2000 to 2013 and the vegetation period considered is April-September. As main results, there were observed four years with high temperatures, namely 2000 (20.4oC-air T, 24.6oC soil T, and 26oC LST, 2003 (20.2oC air T, 23.9oC soil T and 24.5oC LST, 2007 (20.5oC air T, 24.3oC soil T and 25oC LST and 2012 (21.3oC air T, 25.7oC soil T and 26.5oC LST. The correlations between air temperature, soil temperature and LST were statisticaly significant. The diference between air temperature and soil temperature values ranked within 3-4oC, while the difference between soil temperature and land surface temperature obtained from MODIS images was about 0.8oC. Spatially, the highest temperatures were recorded on the Leu-Rotunda Field, the Caracal Plain and the Nedeia Field, and pretty high variations of observed temperatures seemed to depend on vegetation cover. The MODIS images represent one of the most important types of satellite data available for free, which can be successfully used in determining the climatic parameters and can help to predict the changes in plant activity, due to weather phenomena.

Associations of Low-Intensity Resistance Training with Body Composition and Lipid Profile in Obese Patients with Type 2 Diabetes.

Science.gov (United States)

Hamasaki, Hidetaka; Kawashima, Yu; Tamada, Yoshiki; Furuta, Masashi; Katsuyama, Hisayuki; Sako, Akahito; Yanai, Hidekatsu

2015-01-01

Resistance training to increase muscle mass and functional capacity is an integral part of diet and exercise programs for the management of obesity and type 2 diabetes. Low-intensity resistance training with slow movement and tonic force generation (LST) may be a practical and safe regimen for elderly obese individuals but the health benefits are uncertain. This study investigated the effects of LST on body composition and metabolic parameters in obese patients with type 2 diabetes. Twenty-six obese patients with type 2 diabetes engaged in LST training during hospitalization and were advised to maintain this regimen for 12 weeks after discharge. We compared lipid profile, arterial stiffness, and body composition before and after LST training. After 12 weeks of LST training, the ratio of lower extremity muscle mass to body weight increased significantly (0.176 ± 0.028 to 0.184 ± 0.023, mean ± SD), while body fat mass and body fat percentage decreased significantly (36.2 ± 10.9 kg to 34.3 ± 9.4 kg and 41.2 ± 8.6% to 40.1 ± 7.7%, respectively). Moreover, high-density lipoprotein cholesterol was significantly increased (42.2 ± 14 mg/dl to 46.3 ± 12.4 mg/dl) and both free fatty acids and lipoprotein(a) were decreased (665.2 ± 212.1 μEq/l to 525.4 ± 231.3 μEq/l and 15.4 ± 18 mg/dl to 13.8 ± 18 mg/dl, respectively). No significant change was observed in arterial stiffness. Although this study was a non-controlled investigation and some confounding factors including dietary intake, medication and compliance with training might affect the study result, a brief (12-week) LST training program may be a safe and effective strategy for the management of obesity and type 2 diabetes.

Associations of Low-Intensity Resistance Training with Body Composition and Lipid Profile in Obese Patients with Type 2 Diabetes.

Directory of Open Access Journals (Sweden)

Hidetaka Hamasaki

Full Text Available Resistance training to increase muscle mass and functional capacity is an integral part of diet and exercise programs for the management of obesity and type 2 diabetes. Low-intensity resistance training with slow movement and tonic force generation (LST may be a practical and safe regimen for elderly obese individuals but the health benefits are uncertain. This study investigated the effects of LST on body composition and metabolic parameters in obese patients with type 2 diabetes. Twenty-six obese patients with type 2 diabetes engaged in LST training during hospitalization and were advised to maintain this regimen for 12 weeks after discharge. We compared lipid profile, arterial stiffness, and body composition before and after LST training. After 12 weeks of LST training, the ratio of lower extremity muscle mass to body weight increased significantly (0.176 ± 0.028 to 0.184 ± 0.023, mean ± SD, while body fat mass and body fat percentage decreased significantly (36.2 ± 10.9 kg to 34.3 ± 9.4 kg and 41.2 ± 8.6% to 40.1 ± 7.7%, respectively. Moreover, high-density lipoprotein cholesterol was significantly increased (42.2 ± 14 mg/dl to 46.3 ± 12.4 mg/dl and both free fatty acids and lipoprotein(a were decreased (665.2 ± 212.1 μEq/l to 525.4 ± 231.3 μEq/l and 15.4 ± 18 mg/dl to 13.8 ± 18 mg/dl, respectively. No significant change was observed in arterial stiffness. Although this study was a non-controlled investigation and some confounding factors including dietary intake, medication and compliance with training might affect the study result, a brief (12-week LST training program may be a safe and effective strategy for the management of obesity and type 2 diabetes.

Prevalence of low testosterone levels in men with type 2 diabetes mellitus: a cross-sectional study

Directory of Open Access Journals (Sweden)

Ayman A Al Hayek

2013-01-01

Full Text Available Background: A high prevalence of low serum testosterone (LST in men with type 2 diabetes have been reported worldwide. The aim of this study was to determine the prevalence and associated factors of LST in men with type 2 diabetes. Materials and Methods: This was a cross-sectional study, conducted among 1,089 men (aged 30-70 years with type 2 diabetes who consecutively attended a major diabetes center in Amman, Jordan, between August 2008 and February 2009. The patients′ demographic characteristics were collected using a prestructured questionnaire. Duration of diabetes, smoking habits, presence of retinopathy, neuropathy, and nephropathy were collected from the medical records. All participants were asked to complete the Androgen Deficiency in Ageing Male (ADAM questionnaire. Venous blood sample was collected to test for total testosterone (TT, free testosterone (FT, sex hormone binding globulin (SHBG, follicle-stimulating hormone (FSH, luteinizing hormone (LH, prolactin (PRL, serum lipids, and glycosylated hemoglobin (HbA1c. LST was defined as TT <3 ng/ml. Results: Overall, 36.5% of patients with diabetes had TT level <3 ng/ml and 29% had symptoms of androgen deficiency. Of those with serum testosterone level <3 ng/ml, 80.2% had symptoms of androgen deficiency, 16.9% had primary hypogonadism (HG, and 83.1% had secondary HG. Univariate analysis showed a significant relationship between age, income, education, body mass index (BMI, smoking, duration of diabetes, diabetic nephropathy, diabetic neuropathy, and HbA1c. Multivariate logistic regression analysis indicated age, income, BMI, and diabetic neuropathy as the independent risk factors of LST. Conclusions: The prevalence of LST among men with type 2 diabetes is high. Age, income, BMI, and diabetic neuropathy were found to be the independent risk factors for LST.

A Standardized Method for 4D Ultrasound-Guided Peripheral Nerve Blockade and Catheter Placement

Directory of Open Access Journals (Sweden)

N. J. Clendenen

2014-01-01

Full Text Available We present a standardized method for using four-dimensional ultrasound (4D US guidance for peripheral nerve blocks. 4D US allows for needle tracking in multiple planes simultaneously and accurate measurement of the local anesthetic volume surrounding the nerve following injection. Additionally, the morphology and proximity of local anesthetic spread around the target nerve is clearly seen with the described technique. This method provides additional spatial information in real time compared to standard two-dimensional ultrasound.

Accuracy of colonoscopy in localizing colonic cancer.

Science.gov (United States)

Stanciu, C; Trifan, Anca; Khder, Saad Alla

2007-01-01

It is important to establish the precise localization of colonic cancer preoperatively; while colonoscopy is regarded as the diagnostic gold standard for colorectal cancer, its ability to localize the tumor is less reliable. To define the accuracy of colonoscopy in identifying the location of colonic cancer. All of the patients who had a colorectal cancer diagnosed by colonoscopy at the Institute of Gastroenterology and Hepatology, Iaşi and subsequently received a surgical intervention at three teaching hospitals in Iaşi, between January 2001 and December 2005, were included in this study. Endoscopic records and operative notes were carefully reviewed, and tumor localization was recorded. There were 161 patients (89 men, 72 women, aged 61.3 +/- 12.8 years) who underwent conventional surgery for colon cancer detected by colonoscopy during the study period. Twenty-two patients (13.66%) had erroneous colonoscopic localization of the tumors. The overall accuracy of preoperative colonoscopic localization was 87.58%. Colonoscopy is an accurate, reliable method for locating colon cancer, although additional techniques (i.e., endoscopic tattooing) should be performed at least for small lesions.

Local and nonlocal space-time singularities

International Nuclear Information System (INIS)

Konstantinov, M.Yu.

1985-01-01

The necessity to subdivide the singularities into two classes: local and nonlocal, each of them to be defined independently, is proved. Both classes of the singularities are defined, and the relation between the definitions introduced and the standard definition of singularities, based on space-time, incompleteness, is established. The relation between definitions introduced and theorems on the singularity existence is also established

Proton hexality in local grand unification

Energy Technology Data Exchange (ETDEWEB)

Foerste, Stefan; Nilles, Hans Peter [Bonn Univ. (Germany). Bethe Center for Theoretical Physics and Physikalisches Institut; Ramos-Sanchez, Saul [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Vaudrevange, Patrick K.S. [Muenchen Univ. (Germany). Arnold Sommerfeld Center for Theoretical Physics

2010-07-15

Proton hexality is a discrete symmetry that avoids the problem of too fast proton decay in the supersymmetric extension of the standard model. Unfortunately it is inconsistent with conventional grand unification. We show that proton hexality can be incorporated in the scheme of ''Local Grand Unification'' discussed in the framework of model building in (heterotic) string theory. (orig.)

A novel recursive Fourier transform for nonuniform sampled signals: application to heart rate variability spectrum estimation.

Science.gov (United States)

Holland, Alexander; Aboy, Mateo

2009-07-01

We present a novel method to iteratively calculate discrete Fourier transforms for discrete time signals with sample time intervals that may be widely nonuniform. The proposed recursive Fourier transform (RFT) does not require interpolation of the samples to uniform time intervals, and each iterative transform update of N frequencies has computational order N. Because of the inherent non-uniformity in the time between successive heart beats, an application particularly well suited for this transform is power spectral density (PSD) estimation for heart rate variability. We compare RFT based spectrum estimation with Lomb-Scargle Transform (LST) based estimation. PSD estimation based on the LST also does not require uniform time samples, but the LST has a computational order greater than Nlog(N). We conducted an assessment study involving the analysis of quasi-stationary signals with various levels of randomly missing heart beats. Our results indicate that the RFT leads to comparable estimation performance to the LST with significantly less computational overhead and complexity for applications requiring iterative spectrum estimations.

Development of the quality control system of the readout electronics for the large size telescope of the Cherenkov Telescope Array observatory

Energy Technology Data Exchange (ETDEWEB)

Konno, Y.; Kubo, H.; Masuda, S. [Department of Physics, Graduate School of Science, Kyoto University, Kyoto (Japan); Paoletti, R.; Poulios, S. [SFTA Department, Physics Section, University of Siena and INFN, Siena (Italy); Rugliancich, A., E-mail: andrea.rugliancich@pi.infn.it [SFTA Department, Physics Section, University of Siena and INFN, Siena (Italy); Saito, T. [Department of Physics, Graduate School of Science, Kyoto University, Kyoto (Japan)

2016-07-11

The Cherenkov Telescope Array (CTA) is the next generation VHE γ-ray observatory which will improve the currently available sensitivity by a factor of 10 in the range 100 GeV to 10 TeV. The array consists of different types of telescopes, called large size telescope (LST), medium size telescope (MST) and small size telescope (SST). A LST prototype is currently being built and will be installed at the Observatorio Roque de los Muchachos, island of La Palma, Canary islands, Spain. The readout system for the LST prototype has been designed and around 300 readout boards will be produced in the coming months. In this note we describe an automated quality control system able to measure basic performance parameters and quickly identify faulty boards. - Highlights: • The Dragon Board is part of the DAQ of the LST Cherenkov telescope prototype. • We developed an automated quality control system for the Dragon Board. • We check pedestal, linearity, pulse shape and crosstalk values. • The quality control test can be performed on the production line.

Current standard treatment for pediatric glioma patients

International Nuclear Information System (INIS)

Sonoda, Yukihiko; Kumabe, Toshihiro; Saito, Ryuta; Kanamori, Masayuki; Yamashita, Yoji; Tominaga, Teiji

2012-01-01

In this paper, we selected three representative disorders among pediatric gliomas and reviewed standard treatments for these diseases. The formation of this rare disease is involved with BRAF mutation as well as cerebellar pilocytic astrocytoma. Radical resection is not recommended as initial therapy due to high morbidity. Despite its good tumor control, radiotherapy is not a standard therapy due to neuroendocrine and neurocognitive dysfunction. Several papers have reported the effectiveness of platinum-based chemotherapy, which is a useful for induction therapy. Recent progress in molecular analyses has suggested that some markers might be used for staging ependymoma. While total resection is considered to be strongly correlated with patients' survival, the majority of recurrence occurs in the primary site. Despite many clinical trials, chemotherapeutic agents were not found to be effective for this disease. Since whole brain radiation cannot prevent dissemination, local radiation is recommended for adjuvant therapy. The prognosis of this disease is still dismal, and median survival time is within 1 year. Although clinical trials have been conducted to assess the efficacy of chemotherapy prior to, concomitantly with, or after radiotherapy, an effective regimen has not yet been established. Therefore, only conventional local radiotherapy is the standard regimen for this disease. A new therapeutic approach, such as convection-enhanced drug delivery, would be required for improved outcomes in patients with this disease. (author)

Land Surface Temperature- Comparing Data from Polar Orbiting and Geostationary Satellites

Science.gov (United States)

Comyn-Platt, E.; Remedios, J. J.; Good, E. J.; Ghent, D.; Saunders, R.

2012-04-01

Land Surface Temperature (LST) is a vital parameter in Earth climate science, driving long-wave radiation exchanges that control the surface energy budget and carbon fluxes, which are important factors in Numerical Weather Prediction (NWP) and the monitoring of climate change. Satellites offer a convenient way to observe LST consistently and regularly over large areas. A comparison between LST retrieved from a Geostationary Instrument, the Spinning Enhanced Visible and InfraRed Imager (SEVIRI), and a Polar Orbiting Instrument, the Advanced Along Track Scanning Radiometer (AATSR) is presented. Both sensors offer differing benefits. AATSR offers superior precision and spatial resolution with global coverage but given its sun-synchronous platform only observes at two local times, ~10am and ~10pm. SEVIRI provides the high-temporal resolution (every 15 minutes) required for observing diurnal variability of surface temperatures but given its geostationary platform has a poorer resolution, 3km at nadir, which declines at higher latitudes. A number of retrieval methods are applied to the raw satellite data: First order coefficient based algorithms provided on an operational basis by the LandSAF (for SEVIRI) and the University of Leicester (for AATSR); Second order coefficient based algorithms put forward by the University of Valencia; and an optimal estimation method using the 1DVar software provided by the NWP SAF. Optimal estimation is an iterative technique based upon inverse theory, thus is very useful for expanding into data assimilation systems. The retrievals are assessed and compared on both a fine scale using in-situ data from recognised validation sites and on a broad scale using two 100x100 regions such that biases can be better understood. Overall, the importance of LST lies in monitoring daily temperature extremes, e.g. for estimating permafrost thawing depth or risk of crop damage due to frost, hence the ideal dataset would use a combination of observations

122 evaluation of the quality of locally manufactured antimicrobial

African Journals Online (AJOL)

are not available. In order to provide some data, we evaluated the quality of three brands of locally manufactured ... careful control and standardization of the various ... Systems, in Enugu, Optudisc from MEDLABCOP, ... Briefly, a sterilized wire.

Local-field refinement of neutron scattering lengths

International Nuclear Information System (INIS)

Sears, V.F.

1985-01-01

We examine the way in which local field effects in the neutron refractive index affect the values of coherent scattering lengths determined by various kinds of neutron optical measurements. We find that under typical experimental conditions these effects are negligible for interferometry measurements but that they are significant for gravity refractometry measurements, producing changes in the effective scattering length of as much as two or three standard deviations in some cases. Refined values of the scattering length are obtained for the thirteen elements for which data are presently available. The special role of local field effects in neutron transmission is also discussed. (orig.)

Local-field refinement of neutron scattering lengths

Energy Technology Data Exchange (ETDEWEB)

Sears, V F

1985-06-01

We examine the way in which local field effects in the neutron refractive index affect the values of coherent scattering lengths determined by various kinds of neutron optical measurements. We find that under typical experimental conditions these effects are negligible for interferometry measurements but that they are significant for gravity refractometry measurements, producing changes in the effective scattering length of as much as two or three standard deviations in some cases. Refined values of the scattering length are obtained for the thirteen elements for which data are presently available. The special role of local field effects in neutron transmission is also discussed.

Study on the testing standards of quality assurance for CT image

International Nuclear Information System (INIS)

Liu Jingxin; Yang Haishan; Liu Gang; Wang Liyun

2000-01-01

Objective: To establish national testing standards of quality assurance for CT image. Methods: 104 sets of CT system were tested using quality assurance test phantoms and devices including American RMI 461A, RMI 463, MDH 1015 C with ION Chamber, Sweden UNF 9004 kvp meter. These CT were made from different manufacturers including out of date of CT and state-of-art spiral CT system. Thirteen kinds of standards on CT from different countries and 87 sets of technical specifications of CT were collected. The results of the test were compared using phantoms of RMI, Victoreen, Catphan on the same CT system (Siemens HQS). Results: Based on the test results of this study, with reference to the foreign standards and some of regulations in China, CT test items should include high contrast resolution, low contrast resolution, noise, uniformity, mean CT unit, dose slice thickness, localization light, positioning of patient support and gantry tilt. Standards including acceptance test, status test, and constancy test were made in specification. Among them, constancy test equals to IEC 122-2-6; items and results in acceptance test are stricter than in the status test; and low contrast resolution, uniformity, localization light accuracy and positioning of patient support in the acceptance test are even stricter than that in foreign standards. Conclusion: The testing standards of quality assurance for CT developed in this study shows practical and useful in China, which supplemented to the existing international standards

Impact of a product-specific reference standard for the measurement of a PEGylated rFVIII activity: the Swiss Multicentre Field Study.

Science.gov (United States)

Bulla, O; Poncet, A; Alberio, L; Asmis, L M; Gähler, A; Graf, L; Nagler, M; Studt, J-D; Tsakiris, D A; Fontana, P

2017-07-01

Measuring factor VIII (FVIII) activity can be challenging when it has been modified, such as when FVIII is pegylated to increase its circulating half-life. Use of a product-specific reference standard may help avoid this issue. Evaluate the impact of using a product-specific reference standard for measuring the FVIII activity of BAX 855 - a pegylated FVIII - in eight of Switzerland's main laboratories. Factor VIII-deficient plasma, spiked with five different concentrations of BAX 855, plus a control FVIII sample, was sent to the participating laboratories. They measured FVIII activity by using either with a one-stage (OSA) or the chromogenic assay (CA) against their local or a product-specific reference standard. When using a local reference standard, there was an overestimation of BAX 855 activity compared to the target concentrations, both with the OSA and CA. The use of a product-specific reference standard reduced this effect: mean recovery ranged from 127.7% to 213.5% using the OSA with local reference standards, compared to 110% to 183.8% with a product-specific reference standard, and from 146.3% to 182.4% using the CA with local reference standards compared to 72.7% to 103.7% with a product-specific reference standard. In this in vitro study, the type of reference standard had a major impact on the measurement of BAX 855 activity. Evaluation was more accurate and precise when using a product-specific reference standard. © 2017 John Wiley & Sons Ltd.

Setting a protective PM standard: A view from the frontline

Energy Technology Data Exchange (ETDEWEB)

John Paul; Eddie Terrill [Dayton Regional Air Pollution Control Agency, Dayton, OH (United States)

2006-06-15

Several aspects of the US EPA's recent proposal to revise the particulate matter (PM) standards deeply concern state and local air agencies and their representatives with the State and Territorial Air Pollution Program Administrators and the Association of Local Air Pollution Control Offices (STAPPA and ALAPCO). STAPPA and ALAPCO urge EPA to follow the recommendations of its appointed scientific experts and lower the annual average standard to 13 or 14 {mu}mg/m{sup 3} in addition to lowering the daily standard to 35 {mu}m/m{sup 3}. Unless EPA strengthens its proposal consistent with the recommendations of the Clean Air Scientific Advisory Committee (CASAC), STAPPA and ALAPCO are extremely concerned that we will continue to see significant increased premature mortality and adverse health effects throughout the country. For the reasons described in the article STAPPA and ALAPCO urge EPA to eliminate the exemptions for agriculture, mining and rural windblown dust. STAPPA and ALAPCO are troubled that EPA has ignored any commitment to funding the proposed coarse PM network scheduled for deployment in Fiscal Year (FY) 2008. EPA has estimated that the capital costs of this monitoring network could easily exceed US$ 14 million, with annual operating expenses of approximately US$ 13 million. State and local agencies will simply not be able to assume these significant costs. 33 refs.

Using Machine learning method to estimate Air Temperature from MODIS over Berlin

Science.gov (United States)

Marzban, F.; Preusker, R.; Sodoudi, S.; Taheri, H.; Allahbakhshi, M.

2015-12-01

Land Surface Temperature (LST) is defined as the temperature of the interface between the Earth's surface and its atmosphere and thus it is a critical variable to understand land-atmosphere interactions and a key parameter in meteorological and hydrological studies, which is involved in energy fluxes. Air temperature (Tair) is one of the most important input variables in different spatially distributed hydrological, ecological models. The estimation of near surface air temperature is useful for a wide range of applications. Some applications from traffic or energy management, require Tair data in high spatial and temporal resolution at two meters height above the ground (T2m), sometimes in near-real-time. Thus, a parameterization based on boundary layer physical principles was developed that determines the air temperature from remote sensing data (MODIS). Tair is commonly obtained from synoptic measurements in weather stations. However, the derivation of near surface air temperature from the LST derived from satellite is far from straight forward. T2m is not driven directly by the sun, but indirectly by LST, thus T2m can be parameterized from the LST and other variables such as Albedo, NDVI, Water vapor and etc. Most of the previous studies have focused on estimating T2m based on simple and advanced statistical approaches, Temperature-Vegetation index and energy-balance approaches but the main objective of this research is to explore the relationships between T2m and LST in Berlin by using Artificial intelligence method with the aim of studying key variables to allow us establishing suitable techniques to obtain Tair from satellite Products and ground data. Secondly, an attempt was explored to identify an individual mix of attributes that reveals a particular pattern to better understanding variation of T2m during day and nighttime over the different area of Berlin. For this reason, a three layer Feedforward neural networks is considered with LMA algorithm

Reynolds stress of localized toroidal modes

International Nuclear Information System (INIS)

Zhang, Y.Z.; Mahajan, S.M.

1995-02-01

An investigation of the 2D toroidal eigenmode problem reveals the possibility of a new consistent 2D structure, the dissipative BM-II mode. In contrast to the conventional ballooning mode, the new mode is poloidally localized at π/2 (or -π/2), and possesses significant radial asymmetry. The radial asymmetry, in turn, allows the dissipative BM-II to generate considerably larger Reynolds stress as compared to the standard slab drift type modes. It is also shown that a wide class of localized dissipative toroidal modes are likely to be of the dissipative BM-II nature, suggesting that at the tokamak edge, the fluctuation generated Reynolds stress (a possible source of poloidal flow) can be significant

Reynolds stress of localized toroidal modes

International Nuclear Information System (INIS)

Zhang, Y.Z.; Mahajan, S.M.

1995-01-01

An investigation of the 2D toroidal eigenmode problem reveals the possibility of a new consistent 2D structure, the dissipative BM-II mode. In contrast to the conventional ballooning mode, the new mode is poloidally localized at π/2 (or -π/2), and possesses significant radial asymmetry. The radial asymmetry, in turn, allows the dissipative BM-II to generate considerably larger Reynolds stress as compared to the standard slab drift type modes. It is also shown that a wide class of localized dissipative toroidal modes are likely to be of the dissipative BM-II nature, suggesting that at the tokamak edge, the fluctuation generated Reynolds stress (a possible source of poloidal flow) can be significant. (author). 15 refs

MONITORING SPATIOTEMPORAL CHANGES OF HEAT ISLAND IN BABOL CITY DUE TO LAND USE CHANGES

Directory of Open Access Journals (Sweden)

S. K. Alavi Panah

2017-09-01

Full Text Available Urban heat island is one of the most vital environmental risks in urban areas. The advent of remote sensing technology provides better visibility due to the integrated view, low-cost, fast and effective way to study and monitor environmental and humanistic changes. The aim of this study is a spatiotemporal evaluation of land use changes and the heat island in the time period of 1985-2015 for the studied area in the city of Babol. For this purpose, multi-temporal Landsat images were used in this study. For calculating the land surface temperature (LST, single-channel and maximum likelihood algorithms were used, to classify Images. Therefore, land use changes and LST were examined, and thereby the relationship between land-use changes was analyzed with the normalized LST. By using the average and standard deviation of normalized thermal images, the area was divided into five temperature categories, inter alia, very low, low, medium, high and very high and then, the heat island changes in the studied time period were investigated. The results indicate that land use changes for built-up lands increased by 92%, and a noticeable decrease was observed for agricultural lands. The Built-up land changes trend has direct relation with the trend of normalized surface temperature changes. Low and very low-temperature categories which follow a decreasing trend, are related to lands far away from the city. Also, high and very high-temperature categories whose areas increase annually, are adjacent to the city center and exit ways of the town. The results emphasize on the importance of attention of urban planners and managers to the urban heat island as an environmental risk.

Monitoring Spatiotemporal Changes of Heat Island in Babol City due to Land Use Changes

Science.gov (United States)

Alavi Panah, S. K.; Kiavarz Mogaddam, M.; Karimi Firozjaei, M.

2017-09-01

Urban heat island is one of the most vital environmental risks in urban areas. The advent of remote sensing technology provides better visibility due to the integrated view, low-cost, fast and effective way to study and monitor environmental and humanistic changes. The aim of this study is a spatiotemporal evaluation of land use changes and the heat island in the time period of 1985-2015 for the studied area in the city of Babol. For this purpose, multi-temporal Landsat images were used in this study. For calculating the land surface temperature (LST), single-channel and maximum likelihood algorithms were used, to classify Images. Therefore, land use changes and LST were examined, and thereby the relationship between land-use changes was analyzed with the normalized LST. By using the average and standard deviation of normalized thermal images, the area was divided into five temperature categories, inter alia, very low, low, medium, high and very high and then, the heat island changes in the studied time period were investigated. The results indicate that land use changes for built-up lands increased by 92%, and a noticeable decrease was observed for agricultural lands. The Built-up land changes trend has direct relation with the trend of normalized surface temperature changes. Low and very low-temperature categories which follow a decreasing trend, are related to lands far away from the city. Also, high and very high-temperature categories whose areas increase annually, are adjacent to the city center and exit ways of the town. The results emphasize on the importance of attention of urban planners and managers to the urban heat island as an environmental risk.

Nutrient requirements and low-cost balanced diets, based on seasonally available local feedstuffs, for local pigs on smallholder farms in Western Kenya.

Science.gov (United States)

Carter, Natalie Ann; Dewey, Catherine Elizabeth; Thomas, Lian Francesca; Lukuyu, Ben; Grace, Delia; de Lange, Cornelis

2016-02-01

Growth performance of pigs on smallholder farms in the tropics is low. Lack of feedstuffs, seasonal feed shortages, and feeding nutritionally unbalanced diets contribute to slow growth. Low-cost balanced diets are needed to improve pig performance. In this study, we estimated the nutrient requirements of local pigs on smallholder farms in Kenya and developed balanced low-cost diets using seasonally available local feedstuffs. Diets were formulated to provide pigs with 80 % of the nutrient density in corn and soybean meal-based (reference) diets to minimize the cost per unit of energy and other nutrients. Estimated requirements for starting and growing pigs (8 to 35 kg body weight) were as follows: digestible energy (DE) 2960 kcal/kg of dry matter (DM), standardized ileal digestibility (SID) lysine 5.8 g/kg of DM, calcium 2.8 g/kg of DM, standardized total tract digestible (STTD) phosphorous 1.4 g/kg of DM, and crude protein 85 g/kg of DM. Nutrient requirements of local pigs on smallholder farms in Kenya were lower than those of exotic breed pigs raised in commercial settings. Seasonally available local feedstuffs were used to develop low-cost balanced diets. Twenty-two diets are presented based on season, cost, and feedstuff availability. This study has broad applicability as a case study of an approach that could be applied in other tropical regions in which smallholder pig keeping is practiced and where local feedstuffs for pigs are available seasonally.

Analyzing the effects of urban expansion on land surface temperature patterns by landscape metrics: a case study of Isfahan city, Iran.

Science.gov (United States)

Madanian, Maliheh; Soffianian, Ali Reza; Koupai, Saeid Soltani; Pourmanafi, Saeid; Momeni, Mehdi

2018-03-03

Urban expansion can cause extensive changes in land use and land cover (LULC), leading to changes in temperature conditions. Land surface temperature (LST) is one of the key parameters that should be considered in the study of urban temperature conditions. The purpose of this study was, therefore, to investigate the effects of changes in LULC due to the expansion of the city of Isfahan on LST using landscape metrics. To this aim, two Landsat 5 and Landsat 8 images, which had been acquired, respectively, on August 2, 1985, and July 4, 2015, were used. The support vector machine method was then used to classify the images. The results showed that Isfahan city had been encountered with an increase of impervious surfaces; in fact, this class covered 15% of the total area in 1985, while this value had been increased to 30% in 2015. Then LST zoning maps were created, indicating that the bare land and impervious surfaces categories were dominant in high temperature zones, while in the zones where water was present or NDVI was high, LST was low. Then, the landscape metrics in each of the LST zones were analyzed in relation to the LULC changes, showing that LULC changes due to urban expansion changed such landscape properties as the percentage of landscape, patch density, large patch index, and aggregation index. This information could be beneficial for urban planners to monitor and manage changes in the LULC patterns.

Linking potential heat source and sink to urban heat island: Heterogeneous effects of landscape pattern on land surface temperature.

Science.gov (United States)

Li, Weifeng; Cao, Qiwen; Lang, Kun; Wu, Jiansheng

2017-05-15

Rapid urbanization has significantly contributed to the development of urban heat island (UHI). Regulating landscape composition and configuration would help mitigate the UHI in megacities. Taking Shenzhen, China, as a case study area, we defined heat source and heat sink and identified strong and weak sources as well as strong and weak sinks according to the natural and socioeconomic factors influencing land surface temperature (LST). Thus, the potential thermal contributions of heat source and heat sink patches were differentiated. Then, the heterogeneous effects of landscape pattern on LST were examined by using semiparametric geographically weighted regression (SGWR) models. The results showed that landscape composition has more significant effects on thermal environment than configuration. For a strong source, the percentage of patches has a positive impact on LST. Additionally, when mosaicked with some heat sink, even a small improvement in the degree of dispersion of a strong source helps to alleviate UHI. For a weak source, the percentage and density of patches have positive impacts on LST. For a strong sink, the percentage, density, and degree of aggregation of patches have negative impacts on LST. The effects of edge density and patch shape complexity vary spatially with the fragmentation of a strong sink. Similarly, the impacts of a weak sink are mainly exerted via the characteristics of percent, density, and shape complexity of patches. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluation of Three Parametric Models for Estimating Directional Thermal Radiation from Simulation, Airborne, and Satellite Data

Directory of Open Access Journals (Sweden)

Xiangyang Liu

2018-03-01

Full Text Available An appropriate model to correct thermal radiation anisotropy is important for the wide applications of land surface temperature (LST. This paper evaluated the performance of three published directional thermal radiation models—the Roujean–Lagouarde (RL model, the Bidirectional Reflectance Distribution Function (BRDF model, and the Vinnikov model—at canopy and pixel scale using simulation, airborne, and satellite data. The results at canopy scale showed that (1 the three models could describe directional anisotropy well and the Vinnikov model performed the best, especially for erectophile canopy or low leaf area index (LAI; (2 the three models reached the highest fitting accuracy when the LAI varied from 1 to 2; and (3 the capabilities of the three models were all restricted by the hotspot effect, plant height, plant spacing, and three-dimensional structure. The analysis at pixel scale indicated a consistent result that the three models presented a stable effect both on verification and validation, but the Vinnikov model had the best ability in the erectophile canopy (savannas and grassland and low LAI (barren or sparsely vegetated areas. Therefore, the Vinnikov model was calibrated for different land cover types to instruct the angular correction of LST. Validation with the Surface Radiation Budget Network (SURFRAD-measured LST demonstrated that the root mean square (RMSE of the Moderate Resolution Imaging Spectroradiometer (MODIS LST product could be decreased by 0.89 K after angular correction. In addition, the corrected LST showed better spatial uniformity and higher angular correlation.

Valorisation alimentaire et développement local Quality enhancement in food and local development: an example from the department of the Drôme

Directory of Open Access Journals (Sweden)

Anne-Emmanuelle Fiamor

2011-05-01

Full Text Available Cet article s’intéresse aux mécanismes de construction de la légitimité des productions alimentaires locales. Les données présentées sont issues d’une enquête qualitative portant sur les processus de valorisation dans le département de la Drôme. Nous présenterons la construction des normes internes au système d’action de valorisation repéré sur ce territoire à travers trois de ses fondements : l’adhésion à des normes de production, l’adhésion à des normes de distribution ainsi qu’à une inscription dans la vie culturelle locale. À travers ces trois aspects, nous verrons se profiler la logique de valorisation caractérisant ce système. Cette logique de valorisation transmet des valeurs spécifiques aux productions et participe ainsi à les légitimer. La mise en relief de cette forme de légitimité est l’objectif de la réflexion proposée.The aim of this article is to highlight the way in which local food products are given legitimacy, presenting qualitative data from a survey of product enhancement activities in the department of the Drôme. It describes the internal standards defined by three tenets underlying those activities: adherence to production standards; adherence to standards of distribution; and adherence to local cultural life. Our aim is to outline the rationale behind the system - a rationale that in conferring particular values to particular products also helps to give them legitimacy.

Quantification and visualization of carotid segmentation accuracy and precision using a 2D standardized carotid map

International Nuclear Information System (INIS)

Chiu, Bernard; Ukwatta, Eranga; Shavakh, Shadi; Fenster, Aaron

2013-01-01

This paper describes a framework for vascular image segmentation evaluation. Since the size of vessel wall and plaque burden is defined by the lumen and wall boundaries in vascular segmentation, these two boundaries should be considered as a pair in statistical evaluation of a segmentation algorithm. This work proposed statistical metrics to evaluate the difference of local vessel wall thickness (VWT) produced by manual and algorithm-based semi-automatic segmentation methods (ΔT) with the local segmentation standard deviation of the wall and lumen boundaries considered. ΔT was further approximately decomposed into the local wall and lumen boundary differences (ΔW and ΔL respectively) in order to provide information regarding which of the wall and lumen segmentation errors contribute more to the VWT difference. In this study, the lumen and wall boundaries in 3D carotid ultrasound images acquired for 21 subjects were each segmented five times manually and by a level-set segmentation algorithm. The (absolute) difference measures (i.e., ΔT, ΔW, ΔL and their absolute values) and the pooled local standard deviation of manually and algorithmically segmented wall and lumen boundaries were computed for each subject and represented in a 2D standardized map. The local accuracy and variability of the segmentation algorithm at each point can be quantified by the average of these metrics for the whole group of subjects and visualized on the 2D standardized map. Based on the results shown on the 2D standardized map, a variety of strategies, such as adding anchor points and adjusting weights of different forces in the algorithm, can be introduced to improve the accuracy and variability of the algorithm. (paper)

Use of Land Surface Temperature Observations in a Two-Source Energy Balance Model Towards Improved Monitoring of Evapotranspiration and Drought

Science.gov (United States)

Hain, C.; Anderson, M. C.; Otkin, J.; Semmens, K. A.; Zhan, X.; Fang, L.; Li, Z.

2014-12-01

As the world's water resources come under increasing tension due to the dual stressors of climate change and population growth, accurate knowledge of water consumption through evapotranspiration (ET) over a range in spatial scales will be critical in developing adaptation strategies. However, direct validation of ET models is challenging due to lack of available observations that are sufficiently representative at the model grid scale (10-100 km). Prognostic land-surface models require accurate information about observed precipitation, soil moisture storage, groundwater, and artificial controls on water supply (e.g., irrigation, dams, etc.) to reliably link rainfall to evaporative fluxes. In contrast, diagnostic estimates of ET can be generated, with no prior knowledge of the surface moisture state, by energy balance models using thermal-infrared remote sensing of land-surface temperature (LST) as a boundary condition. One such method, the Atmosphere Land Exchange Inverse (ALEXI) model provides estimates of surface energy fluxes through the use of mid-morning change in LST and radiation inputs. The LST inputs carry valuable proxy information regarding soil moisture and its effect on soil evaporation and canopy transpiration. Additionally, the Evaporative Stress Index (ESI) representing anomalies in the ratio of actual-to-potential ET has shown to be a reliable indicator of drought. ESI maps over the continental US show good correspondence with standard drought metrics and with patterns of precipitation, but can be generated at significantly higher spatial resolution due to a limited reliance on ground observations. Furthermore, ESI is a measure of actual stress rather than potential for stress, and has physical relevance to projected crop development. Because precipitation is not used in construction of the ESI, it provides an independent assessment of drought conditions and has particular utility for real-time monitoring in regions with sparse rainfall data or

Higher than standard radiation doses (≥72 Gy) with or without androgen deprivation in the treatment of localized prostate cancer

International Nuclear Information System (INIS)

Kupelian, Patrick A.; Mohan, Dasarahally S.; Lyons, Janice; Klein, Eric A.; Reddy, Chandana A.

2000-01-01

), iPSA (continuous variable), bGS (≤6 vs. ≥7), use of AD (yes vs. no), radiation technique (conformal versus standard), and radiation dose (continuous variable). T-stage (p < 0.001), iPSA (p < 0.001), bGS (p < 0.001), and RT dose (p < 0.001) were independent predictors of outcome. Age (p = 0.74), race (p = 0.96), radiation technique (p = 0.15), and use of AD (p = 0.31) were not. We observed 11% clinical failures (local, distant, or both) at 5 years and 15% at 8 years for the entire cohort. There was a statistically significant improvement with higher radiation doses (p 0.032). The 5-year clinical relapse rates for patients receiving ≥72 Gy versus <72 Gy were 5% and 12%, respectively. The 8-year clinical relapse rates for patients receiving radiation doses ≥72 Gy versus <72 Gy were 5% and 17%, respectively (p = 0.026). Conclusion: Patients receiving radiation doses exceeding 72 Gy had significantly better bRFS and clinical disease-free survival rates. Although results need to be confirmed with longer follow-up, these preliminary results are extremely encouraging. If these results are confirmed by other institutions and by longer follow-up, RT doses exceeding 72 Gy should be considered as standard of care

Source localization of rhythmic ictal EEG activity: a study of diagnostic accuracy following STARD criteria.

Science.gov (United States)

Beniczky, Sándor; Lantz, Göran; Rosenzweig, Ivana; Åkeson, Per; Pedersen, Birthe; Pinborg, Lars H; Ziebell, Morten; Jespersen, Bo; Fuglsang-Frederiksen, Anders

2013-10-01

Although precise identification of the seizure-onset zone is an essential element of presurgical evaluation, source localization of ictal electroencephalography (EEG) signals has received little attention. The aim of our study was to estimate the accuracy of source localization of rhythmic ictal EEG activity using a distributed source model. Source localization of rhythmic ictal scalp EEG activity was performed in 42 consecutive cases fulfilling inclusion criteria. The study was designed according to recommendations for studies on diagnostic accuracy (STARD). The initial ictal EEG signals were selected using a standardized method, based on frequency analysis and voltage distribution of the ictal activity. A distributed source model-local autoregressive average (LAURA)-was used for the source localization. Sensitivity, specificity, and measurement of agreement (kappa) were determined based on the reference standard-the consensus conclusion of the multidisciplinary epilepsy surgery team. Predictive values were calculated from the surgical outcome of the operated patients. To estimate the clinical value of the ictal source analysis, we compared the likelihood ratios of concordant and discordant results. Source localization was performed blinded to the clinical data, and before the surgical decision. Reference standard was available for 33 patients. The ictal source localization had a sensitivity of 70% and a specificity of 76%. The mean measurement of agreement (kappa) was 0.61, corresponding to substantial agreement (95% confidence interval (CI) 0.38-0.84). Twenty patients underwent resective surgery. The positive predictive value (PPV) for seizure freedom was 92% and the negative predictive value (NPV) was 43%. The likelihood ratio was nine times higher for the concordant results, as compared with the discordant ones. Source localization of rhythmic ictal activity using a distributed source model (LAURA) for the ictal EEG signals selected with a standardized method

Developing first time-series of land surface temperature from AATSR with uncertainty estimates

Science.gov (United States)

Ghent, Darren; Remedios, John

2013-04-01

Land surface temperature (LST) is the radiative skin temperature of the land, and is one of the key parameters in the physics of land-surface processes on regional and global scales. Earth Observation satellites provide the opportunity to obtain global coverage of LST approximately every 3 days or less. One such source of satellite retrieved LST has been the Advanced Along-Track Scanning Radiometer (AATSR); with LST retrieval being implemented in the AATSR Instrument Processing Facility in March 2004. Here we present first regional and global time-series of LST data from AATSR with estimates of uncertainty. Mean changes in temperature over the last decade will be discussed along with regional patterns. Although time-series across all three ATSR missions have previously been constructed (Kogler et al., 2012), the use of low resolution auxiliary data in the retrieval algorithm and non-optimal cloud masking resulted in time-series artefacts. As such, considerable ESA supported development has been carried out on the AATSR data to address these concerns. This includes the integration of high resolution auxiliary data into the retrieval algorithm and subsequent generation of coefficients and tuning parameters, plus the development of an improved cloud mask based on the simulation of clear sky conditions from radiance transfer modelling (Ghent et al., in prep.). Any inference on this LST record is though of limited value without the accompaniment of an uncertainty estimate; wherein the Joint Committee for Guides in Metrology quote an uncertainty as "a parameter associated with the result of a measurement that characterizes the dispersion of the values that could reasonably be attributed to the measurand that is the value of the particular quantity to be measured". Furthermore, pixel level uncertainty fields are a mandatory requirement in the on-going preparation of the LST product for the upcoming Sea and Land Surface Temperature (SLSTR) instrument on-board Sentinel-3

Does the individual adaption of standardized speech paradigmas for clinical functional Magnetic Resonance Imaging (fMRI) effect the localization of the language-dominant hemisphere and of Broca's and Wernicke's areas

International Nuclear Information System (INIS)

Konrad, F.; Nennig, E.; Kress, B.; Sartor, K.; Stippich, C.; Ochmann, H.

2005-01-01

Purpose: Functional magnetic resonance imaging (fMRI) localizes Broca's area (B) and Wernicke's area (W) and the hemisphere dominant for language. In clinical fMRI, adapting the stimulation paradigms to each patient's individual cognitive capacity is crucial for diagnostic success. To interpret clinical fMRI findings correctly, we studied the effect of varying frequency and number of stimuli on functional localization, determination of language dominance and BOLD signals. Materials and Methods: Ten volunteers (VP) were investigated at 1.5 Tesla during visually triggered sentence generation using a standardized block design. In four different measurements, the stimuli were presented to each VP with frequencies of (1/1)s, (1/2)s,(1/3)s and (1/6)s. Results: The functional localizations and the correlations of the measured BOLD signals to the applied hemodynamic reference function (r) were almost independent from frequency and number of the stimuli in both hemispheres, whereas the relative BOLD signal changes (ΔS) in B and W increased with the stimulation rate, which also changed the lateralization indices. The strongest BOLD activations were achieved with the highest stimulation rate or with the maximum language production task, respectively. Conclusion: The adaptation of language paradigms necessary in clinical fMRI does not alter the functional localizations but changes the BOLD signals and language lateralization which should not be attributed to the underlying brain pathology. (orig.)

[Does the individual adaptation of standardized speech paradigmas for clinical functional magnetic resonance imaging (fMRI) effect the localization of the language-dominant hemisphere and of Broca's and Wernicke's areas].

Science.gov (United States)

Konrad, F; Nennig, E; Ochmann, H; Kress, B; Sartor, K; Stippich, C

2005-03-01

Functional magnetic resonance imaging (fMRI) localizes Broca's area (B) and Wernicke's area (W) and the hemisphere dominant for language. In clinical fMRI, adapting the stimulation paradigms to each patient's individual cognitive capacity is crucial for diagnostic success. To interpret clinical fMRI findings correctly, we studied the effect of varying frequency and number of stimuli on functional localization, determination of language dominance and BOLD signals. Ten volunteers (VP) were investigated at 1.5 Tesla during visually triggered sentence generation using a standardized block design. In four different measurements, the stimuli were presented to each VP with frequencies of 1/1 s, (1/2) s, (1/3) s and (1/6) s. The functional localizations and the correlations of the measured BOLD signals to the applied hemodynamic reference function (r) were almost independent from frequency and number of the stimuli in both hemispheres, whereas the relative BOLD signal changes (DeltaS) in B and W increased with the stimulation rate, which also changed the lateralization indices. The strongest BOLD activations were achieved with the highest stimulation rate or with the maximum language production task, respectively. The adaptation of language paradigms necessary in clinical fMRI does not alter the functional localizations but changes the BOLD signals and language lateralization which should not be attributed to the underlying brain pathology.

Thermal behavior induced by vacuum polarization on causal horizons in comparison with the standard heat bath formalism

Energy Technology Data Exchange (ETDEWEB)

Schroer, Bert [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro, RJ (Brazil)]|[Institut fuer Theoretische Physik, Berlin (Germany); E-mail schroer@cbpf.br

2003-02-01

Modular theory of operator algebras and the associated K MS property are used to obtain a unified description for the thermal aspects of the standard heat bath situation and those caused by quantum vacuum fluctuations from localization. An algebraic variant of light front holography reveals that the vacuum polarization on wedge horizons is compressed into the light ray direction. Their absence in the transverse direction is the prerequisite to an area (generalized Banknotes-) behavior of entropy-like measures which reveal the loss of purity due to restrictions to wedges and their horizons. Besides the well-known fact that localization-induced (generalized Hawking-) temperature is fixed by the geometric aspects, this area behavior (versus the standard volume dependence) constitutes the main difference between localization-caused and standard thermal behavior. (author)

Optimizing radiation exposure for CT localizer radiographs

Energy Technology Data Exchange (ETDEWEB)

Bohrer, Evelyn; Maeder, Ulf; Fiebich, Martin [Univ. of Applied Sciences, Giessen (Germany). Inst. of Medical Physics and Radiation Protection-IMPS; Schaefer, Stefan; Krombach, Gabriele A. [Univ. Hospital Giessen (Germany). Dept. of Radiology; Noel, Peter B. [Technische Univ. Muenchen (Germany). Dept. of Diagnostic and Interventional Radiology

2017-08-01

The trend towards submillisievert CT scans leads to a higher dose fraction of localizer radiographs in CT examinations. The already existing technical capabilities make dose optimization of localizer radiographs worthwhile. Modern CT scanners apply automatic exposure control (AEC) based on attenuation data in such a localizer. Therefore not only this aspect but also the detectability of anatomical landmarks in the localizer for the desired CT scan range adjustment needs to be considered. The effective dose of a head, chest, and abdomen-pelvis localizer radiograph with standard factory settings and user-optimized settings was determined using Monte Carlo simulations. CT examinations of an anthropomorphic phantom were performed using multiple sets of acquisition parameters for the localizer radiograph and the AEC for the subsequent helical CT scan. Anatomical landmarks were defined to assess the image quality of the localizer. CTDI{sub vol} and effective mAs per slice of the helical CT scan were recorded to examine the impact of localizer settings on a helical CT scan. The dose of the localizer radiograph could be decreased by more than 90% while the image quality remained sufficient when selecting the lowest available settings (80 kVp, 20 mA, pa tube position). The tube position during localizer acquisition had a greater impact on the AEC than the reduction of tube voltage and tube current. Except for the use of a pa tube position, all changes of acquisition parameters for the localizer resulted in a decreased total radiation exposure. A dose reduction of CT localizer radiograph is necessary and possible. In the examined CT system there was no negative impact on the modulated helical CT scan when the lowest tube voltage and tube current were used for the localizer.

New standard on safety for hydrogen systems in spanish. Keys for understanding and use

Energy Technology Data Exchange (ETDEWEB)

Luis Aprea, Jose [CNEA, Argentine Atomic Energy Commission - AAH - IRAM - Comahue University, CC 805 - Neuquen (Argentina)

2008-07-15

The present paper approaches all the preliminary, normative and additional elements observed during the work carried out by the Argentine standardization board to count in the country with a normative document that covers the expectations of the local community of users and other Spanish-speaking user, about the integral safety for the hydrogen systems. The antecedents and the process of adoption of an international standard and its adaptation to the local media are analyzed. The result has been the Standard IRAM/ISO 15916 that intends to offer, to all the users and especially to those who are not familiar with the technology, a base to understand the subject of safety, thus enhancing the education of the general public in hydrogen safety matters. (author)

Malaysian made condoms sold locally as well as exported.

Science.gov (United States)

1979-01-01

Malaysia, famous for its natural rubber, is also producing condoms made from local rubber. About 40,000 gross of condoms a month are being produced by a factory with about 30 female workers. 30-40% of the production is exported to Europe, Middle East, Asia, Japan, Singapore and South America. The size of the condoms conform to international standards, 49 mm and 52 mm. As there is a greater demand for the 52 mm. condoms overseas, the company produces more of this than the 49 mm. condoms. In April 1975, the Standard Institution and Industrial Research of Malaysia gave its quality control approval to a condom which can hold 5 gallons of water and with thickness varying from 0.03 mm, 0.06 mm. and 0.05-0.07 mm. A 10% tax/piece and a 5% surtax are imposed on imported condoms to protect the local industry from foreign competition. Local condoms are sold tax-free. Pink and black colored condoms appear to be popular among consumers. Although complaints are few, 1 in 10,000 users may suffer from allergic problems because of the silicone oil treatment of the condoms. Another local condom factory which uses Malaysian rubber for condom manufacture is located in Klang, approximately 24 miles from Kuala Lumpur; the factory has 25 workers producing 12,000 gross of lubricated and non-lubricated condoms for local consumption only. There is increasing evidence that condoms are increasing in popularity in Malaysia and that the average consumer is now being more selective in choosing contraceptive methods.

swLORETA: a novel approach to robust source localization and synchronization tomography

International Nuclear Information System (INIS)

Palmero-Soler, Ernesto; Dolan, Kevin; Hadamschek, Volker; Tass, Peter A

2007-01-01

Standardized low-resolution brain electromagnetic tomography (sLORETA) is a widely used technique for source localization. However, this technique still has some limitations, especially under realistic noisy conditions and in the case of deep sources. To overcome these problems, we present here swLORETA, an improved version of sLORETA, obtained by incorporating a singular value decomposition-based lead field weighting. We show that the precision of the source localization can further be improved by a tomographic phase synchronization analysis based on swLORETA. The phase synchronization analysis turns out to be superior to a standard linear coherence analysis, since the latter cannot distinguish between real phase locking and signal mixing

An explicit local uniform large deviation bound for Brownian bridges

NARCIS (Netherlands)

Wittich, O.

2005-01-01

By comparing curve length in a manifold and a standard sphere, we prove a local uniform bound for the exponent in the Large Deviation formula that describes the concentration of Brownian bridges to geodesics.

Disordered locality as an explanation for the dark energy

International Nuclear Information System (INIS)

Prescod-Weinstein, Chanda; Smolin, Lee

2009-01-01

We discuss a novel explanation of the dark energy as a manifestation of macroscopic nonlocality coming from quantum gravity, as proposed by Markopoulou [F. Markopoulou (private communication)]. It has been previously suggested that in a transition from an early quantum geometric phase of the Universe to a low temperature phase characterized by an emergent spacetime metric, locality might have been 'disordered'. This means that there is a mismatch of micro-locality, as determined by the microscopic quantum dynamics and macro-locality as determined by the classical metric that governs the emergent low energy physics. In this paper we discuss the consequences for cosmology by studying a simple extension of the standard cosmological models with disordered locality. We show that the consequences can include a naturally small vacuum energy.

Improvement of Hungarian Joint Terminal Attack Program

Science.gov (United States)

2013-06-13

LST Laser Spot Tracker NVG Night Vision Goggle ROMAD Radio Operator Maintainer and Driver ROVER Remotely Operated Video Enhanced Receiver TACP...visual target designation. The other component consists of a laser spot tracker (LST), which identifies targets by tracking laser energy reflecting...capability for every type of night time missions, laser spot tracker for laser spot search missions, remotely operated video enhanced receiver

Synthesis of industrial applications of local approach to fracture models

International Nuclear Information System (INIS)

Eripret, C.

1993-03-01

This report gathers different applications of local approach to fracture models to various industrial configurations, such as nuclear pressure vessel steel, cast duplex stainless steels, or primary circuit welds such as bimetallic welds. As soon as models are developed on the basis of microstructural observations, damage mechanisms analyses, and fracture process, the local approach to fracture proves to solve problems where classical fracture mechanics concepts fail. Therefore, local approach appears to be a powerful tool, which completes the standard fracture criteria used in nuclear industry by exhibiting where and why those classical concepts become unvalid. (author). 1 tab., 18 figs., 25 refs

Localization and the interface between quantum mechanics, quantum field theory and quantum gravity I. (The two antagonistic localizations and their asymptotic compatibility)

International Nuclear Information System (INIS)

Schroer, Bert; Freie Universitaet, Berlin

2010-02-01

It is shown that there are significant conceptual differences between QM and QFT which make it difficult to view the latter as just a relativistic extension of the principles of QM. At the root of this is a fundamental distinction between Born localization in QM (which in the relativistic context changes its name to Newton- Wigner localization) and modular localization which is the localization underlying QFT, after one separates it from its standard presentation in terms of field coordinates. The first comes with a probability notion and projection operators, whereas the latter describes causal propagation in QFT and leads to thermal aspects of locally reduced finite energy states. The Born-Newton-Wigner localization in QFT is only applicable asymptotically and the covariant correlation between asymptotic in and out localization projectors is the basis of the existence of an invariant scattering matrix. In this first part of a two part essay the modular localization (the intrinsic content of field localization) and its philosophical consequences take the center stage. Important physical consequences of vacuum polarization will be the main topic of part II. The present division into two semi-autonomous essays is the result of a partition and extension of an originally one-part manuscript. (author)

Localization and the interface between quantum mechanics, quantum field theory and quantum gravity I (The two antagonistic localizations and their asymptotic compatibility)

International Nuclear Information System (INIS)

Schroer, Bert

2010-01-01

It is shown that there are significant conceptual differences between QM and QFT which make it difficult to view the latter as just a relativistic extension of the principles of QM. At the root of this is a fundamental distinction between Born-localization in QM (which in the relativistic context changes its name to Newton-Wigner localization) and modular localization which is the localization underlying QFT, after one separates it from its standard presentation in terms of field coordinates. The first comes with a probability notion and projection operators, whereas the latter describes causal propagation in QFT and leads to thermal aspects of locally reduced finite energy states. The Born-Newton-Wigner localization in QFT is only applicable asymptotically and the covariant correlation between asymptotic in and out localization projectors is the basis of the existence of an invariant scattering matrix. In this first part of a two part essay the modular localization (the intrinsic content of field localization) and its philosophical consequences take the center stage. Important physical consequences of vacuum polarization will be the main topic of part II. The present division into two semi-autonomous essays is the result of a partition and extension of an originally one-part manuscript. (author)

Localization and the interface between quantum mechanics, quantum field theory and quantum gravity I. (The two antagonistic localizations and their asymptotic compatibility)

Energy Technology Data Exchange (ETDEWEB)

Schroer, Bert [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro, RJ (Brazil); Freie Universitaet, Berlin (Germany). Inst. fuer Theoretische Physik

2010-02-15

It is shown that there are significant conceptual differences between QM and QFT which make it difficult to view the latter as just a relativistic extension of the principles of QM. At the root of this is a fundamental distinction between Born localization in QM (which in the relativistic context changes its name to Newton- Wigner localization) and modular localization which is the localization underlying QFT, after one separates it from its standard presentation in terms of field coordinates. The first comes with a probability notion and projection operators, whereas the latter describes causal propagation in QFT and leads to thermal aspects of locally reduced finite energy states. The Born-Newton-Wigner localization in QFT is only applicable asymptotically and the covariant correlation between asymptotic in and out localization projectors is the basis of the existence of an invariant scattering matrix. In this first part of a two part essay the modular localization (the intrinsic content of field localization) and its philosophical consequences take the center stage. Important physical consequences of vacuum polarization will be the main topic of part II. The present division into two semi-autonomous essays is the result of a partition and extension of an originally one-part manuscript. (author)

Humoral and In Vivo Cellular Immunity against the Raw Insect-Derived Recombinant Leishmania infantum Antigens KMPII, TRYP, LACK, and papLe22 in Dogs from an Endemic Area

Science.gov (United States)

Todolí, Felicitat; Solano-Gallego, Laia; de Juan, Rafael; Morell, Pere; del Carmen Núñez, Maria; Lasa, Rodrigo; Gómez-Sebastián, Silvia; Escribano, José M.; Alberola, Jordi; Rodríguez-Cortés, Alhelí

2010-01-01

Leishmania infantum causes visceral leishmaniasis, a severe zoonotic and systemic disease that is fatal if left untreated. Identification of the antigens involved in Leishmania-specific protective immune response is a research priority for the development of effective control measures. For this purpose, we evaluated, in 27 dogs from an enzootic zone, specific humoral and cellular immune response by delayed-type hypersensitivity (DTH) skin test both against total L. infantum antigen and the raw Trichoplusia ni insect-derived kinetoplastid membrane protein-11 (rKMPII), tryparedoxin peroxidase (rTRYP), Leishmania homologue of receptors for activated C kinase (rLACK), and 22-kDa potentially aggravating protein of Leishmania (rpapLe22) antigens from this parasite. rTRYP induced the highest number of positive DTH responses (55% of leishmanin skin test [LST]-positive dogs), showing that TRYP antigen is an important T cell immunogen, and it could be a promising vaccine candidate against this disease. When TRYP-DTH and KMPII-DTH tests were evaluated in parallel, 82% of LST-positive dogs were detected, suggesting that both antigens could be considered as components of a standardized DTH immunodiagnostic tool for dogs. PMID:21118936

The Impact Analysis of Water Body Landscape Pattern on Urban Heat Island: A Case Study of Wuhan City

Directory of Open Access Journals (Sweden)

Bohan Yang

2015-01-01

Full Text Available Based on the LST and the landscape metrics of water body with remote sensing technique and spatial analysis, the relationship between the mean LST and the attributes of water body was revealed via Pearson’s correlation analysis and multiple stepwise regression analysis. Result showed that, in 32 class-based metrics we selected, the proportion of water body, average water body size, the isolation and fragmentation of water body, and other eight metrics have high correlation with the LST. As a resultant force, the quantity, shape, and spatial distribution of water body affect the forming of temperature. We found that the quantity and spatial pattern of city water body could be allocated reasonably to maximize its cooling effect.

Derivation of Land Surface Temperature for Landsat-8 TIRS Using a Split Window Algorithm

Directory of Open Access Journals (Sweden)

Offer Rozenstein

2014-03-01

Full Text Available Land surface temperature (LST is one of the most important variables measured by satellite remote sensing. Public domain data are available from the newly operational Landsat-8 Thermal Infrared Sensor (TIRS. This paper presents an adjustment of the split window algorithm (SWA for TIRS that uses atmospheric transmittance and land surface emissivity (LSE as inputs. Various alternatives for estimating these SWA inputs are reviewed, and a sensitivity analysis of the SWA to misestimating the input parameters is performed. The accuracy of the current development was assessed using simulated Modtran data. The root mean square error (RMSE of the simulated LST was calculated as 0.93 °C. This SWA development is leading to progress in the determination of LST by Landsat-8 TIRS.

Development of the quality control system of the readout electronics for the large size telescope of the Cherenkov Telescope Array observatory

Science.gov (United States)

Konno, Y.; Kubo, H.; Masuda, S.; Paoletti, R.; Poulios, S.; Rugliancich, A.; Saito, T.

2016-07-01

The Cherenkov Telescope Array (CTA) is the next generation VHE γ-ray observatory which will improve the currently available sensitivity by a factor of 10 in the range 100 GeV to 10 TeV. The array consists of different types of telescopes, called large size telescope (LST), medium size telescope (MST) and small size telescope (SST). A LST prototype is currently being built and will be installed at the Observatorio Roque de los Muchachos, island of La Palma, Canary islands, Spain. The readout system for the LST prototype has been designed and around 300 readout boards will be produced in the coming months. In this note we describe an automated quality control system able to measure basic performance parameters and quickly identify faulty boards.

Flexibility First, Then Standardize: A Strategy for Growing Inter-Departmental Systems.

Science.gov (United States)

á Torkilsheyggi, Arnvør

2015-01-01

Any attempt to use IT to standardize work practices faces the challenge of finding a balance between standardization and flexibility. In implementing electronic whiteboards with the goal of standardizing inter-departmental practices, a hospital in Denmark chose to follow the strategy of "flexibility first, then standardization." To improve the local grounding of the system, they first focused on flexibility by configuring the whiteboards to support intra-departmental practices. Subsequently, they focused on standardization by using the white-boards to negotiate standardization of inter-departmental practices. This paper investigates the chosen strategy and finds: that super users on many wards managed to configure the whiteboard to support intra-departmental practices; that initiatives to standardize inter-departmental practices improved coordination of certain processes; and that the chosen strategy posed a challenge for finding the right time and manner to shift the balance from flexibility to standardization.

The Need for Standardization in SMEs Networks

Directory of Open Access Journals (Sweden)

Ivana Mijatovic

2014-05-01

Full Text Available Many SMEs networking initiatives failed because of the absence of trust among companies and between companies and government, leadership and management approaches as well as absence of entrepreneurial skills in managing business networks. Even though local governments or regional agencies have a capacity to mobilize actors from the public and private sectors, generic public initiatives are proved not to be enough. The private sector should also be supported in gathering around joint interests and solving their mutual problems, thus improving business and competitiveness. Research, management and policy instruments to support SMEs will need to have some other directions. Can standardization be one of the directions? The main objective of this paper is to present some aspects of need for standardization in SMEs networking initiatives. The solution to actual or potential matching problems (intended and expected to be used repeatedly or continuously, during a certain period, by a substantial number of parties for whom they are meant can be formalized as standard. The standard development process can serve as basis for building connections and trust among cluster members. Even though some researche emphasizes the role of ad hoc de facto standards as well as standardization in the contexts of achievement of the optimum degree of order in SMEs networks, specific experience is evident in all cases, but experience in design of ad hoc de facto standards and standardization management are still missing.

The value of Standards and Labelling: an international cost-benefit analysis tool for Standards and Labelling programs with results for Central American countries

International Nuclear Information System (INIS)

Buskirk, Robert D. Van; McNeil, Michael A.; Letschert, Virginie E.

2005-01-01

We describe a cost-benefit spreadsheet analysis tool that provides an evaluation of the net impacts of an appliance standards and labelling (SandL) program. The tool is designed to provide a rough estimate at very low cost to local analysts, while allowing for a more accurate evaluation when detailed local data are available. The methodology takes a bottom-up engineering approach, beginning with appliance-specific engineering parameters relating efficiency improvement and incremental costs associated with specific design technologies. Efficiency improvement afforded by each potential policy option is combined with local appliance use patterns to estimate average annual energy consumption for each appliance. This information is combined with appliance lifetime data and local energy prices to provide a life cycle cost impact assessment at the household level. In addition to household level impacts, the analysis tool forecasts future appliance sales, in order to calculate potential energy savings, consumer financial impacts and carbon emissions reductions at the national level. In order to demonstrate the features of the policy model employed, this poster presents a regional analysis based on the most recent publicly available appliance data. In particular, a set of developing countries in Central America were chosen as an example. Taken as a whole, the Central American results demonstrate the general level of benefit which could be afforded in these countries. Comparison between the countries reveals the key parameters determining the benefit a given country can expect from a standards program

In their own time: the family experience during the process of withdrawal of life-sustaining therapy.

Science.gov (United States)

Wiegand, Debra

2008-10-01

Withdrawal of life-sustaining therapy (LST) occurs commonly in critical care units, yet little is known about the family experience with this process. The purpose of this study was to understand the lived experience of families participating in the process of withdrawal of LST from a family member with an unexpected, life-threatening illness or injury. A hermeneutic phenomenological approach was used as nineteen families were interviewed and observed. Within and across family analyses were conducted. Methodological rigor was established and redundancy was achieved. The categories that evolved from the data included: this happens to other families, time to understand the severity of the illness or injury, time to see if health would be restored, riding a roller coaster, family readiness: willingness to consider withdrawal of LST as a possible option, one step at a time, family readiness: time to make a decision, the family will go on, and waiting for a miracle. The family experience participating in the process of withdrawal of LST happened for families "in their own time." The results of this study have important implications for clinical practice and future research.

In Their Own Time: The Family Experience during the Process of Withdrawal of Life-Sustaining Therapy

Science.gov (United States)

2008-01-01

Abstract Withdrawal of life-sustaining therapy (LST) occurs commonly in critical care units, yet little is known about the family experience with this process. The purpose of this study was to understand the lived experience of families participating in the process of withdrawal of LST from a family member with an unexpected, life-threatening illness or injury. A hermeneutic phenomenological approach was used as nineteen families were interviewed and observed. Within and across family analyses were conducted. Methodological rigor was established and redundancy was achieved. The categories that evolved from the data included: this happens to other families, time to understand the severity of the illness or injury, time to see if health would be restored, riding a roller coaster, family readiness: willingness to consider withdrawal of LST as a possible option, one step at a time, family readiness: time to make a decision, the family will go on, and waiting for a miracle. The family experience participating in the process of withdrawal of LST happened for families “in their own time.” The results of this study have important implications for clinical practice and future research. PMID:18980452

Quantifying the Contributions of Environmental Parameters to Ceres Surface Net Radiation Error in China

Science.gov (United States)

Pan, X.; Yang, Y.; Liu, Y.; Fan, X.; Shan, L.; Zhang, X.

2018-04-01

Error source analyses are critical for the satellite-retrieved surface net radiation (Rn) products. In this study, we evaluate the Rn error sources in the Clouds and the Earth's Radiant Energy System (CERES) project at 43 sites from July in 2007 to December in 2007 in China. The results show that cloud fraction (CF), land surface temperature (LST), atmospheric temperature (AT) and algorithm error dominate the Rn error, with error contributions of -20, 15, 10 and 10 W/m2 (net shortwave (NSW)/longwave (NLW) radiation), respectively. For NSW, the dominant error source is algorithm error (more than 10 W/m2), particularly in spring and summer with abundant cloud. For NLW, due to the high sensitivity of algorithm and large LST/CF error, LST and CF are the largest error sources, especially in northern China. The AT influences the NLW error large in southern China because of the large AT error in there. The total precipitable water has weak influence on Rn error even with the high sensitivity of algorithm. In order to improve Rn quality, CF and LST (AT) error in northern (southern) China should be decreased.

Probability density function of a puff dispersing from the wall of a turbulent channel

Science.gov (United States)

Nguyen, Quoc; Papavassiliou, Dimitrios

2015-11-01

Study of dispersion of passive contaminants in turbulence has proved to be helpful in understanding fundamental heat and mass transfer phenomena. Many simulation and experimental works have been carried out to locate and track motions of scalar markers in a flow. One method is to combine Direct Numerical Simulation (DNS) and Lagrangian Scalar Tracking (LST) to record locations of markers. While this has proved to be useful, high computational cost remains a concern. In this study, we develop a model that could reproduce results obtained by DNS and LST for turbulent flow. Puffs of markers with different Schmidt numbers were released into a flow field at a frictional Reynolds number of 150. The point of release was at the channel wall, so that both diffusion and convection contribute to the puff dispersion pattern, defining different stages of dispersion. Based on outputs from DNS and LST, we seek the most suitable and feasible probability density function (PDF) that represents distribution of markers in the flow field. The PDF would play a significant role in predicting heat and mass transfer in wall turbulence, and would prove to be helpful where DNS and LST are not always available.

The Effect of Intellectual Property Standards on the Catch-Up Process Of Emerging Market Economies

DEFF Research Database (Denmark)

Darendeli, Izzet; Brandl, Kristin Martina; Hamilton, III, Robert D.

2014-01-01

The catch-up process of emerging market economies is dependent on multiple factors, such as local governmental regulations but also global industry developments. We investigate how intellectual property (IP) protection standards affect this catch-up process. The alignment of these standards...

The negotiation of fair trade standards within Ecuadorian flower plantations

Directory of Open Access Journals (Sweden)

Angus Lyall

2014-03-01

Full Text Available Fairtrade International (FLO applies requirements or “standards” for certification in agroindustries in order to channel resources to workers, improve their conditions, and “empower” them, even requiring freedom of association. Researchers have signaled a “dilution” (Jaffee, 2012 of standards in recent years. I take into account the case of the Ecuadorian cut-flower industry to show that FLO’s impacts on power relations ought to be analyzed not in terms of the standards, but rather in terms of the local negotiation of standards within territorial power relations. For this case, I point out that before FLO’s criticisms of conventional market mechanisms, standards generate better conditions, but also facilitate the re-consolidation of labor control.   

The effect of types of banner ad, Web localization, and customer involvement on Internet users' attitudes.

Science.gov (United States)

Chen, Jengchung Victor; Ross, William H; Yen, David C; Akhapon, Lerdsuwankij

2009-02-01

In this study, three characteristics of Web sites were varied: types of banner ad, Web localization, and involvement in purchasing a product. The dependent variable was attitude toward the site. In laboratory experiments conducted in Thailand and Taiwan, participants browsed versions of a Web site containing different types of banner ads and products. As a within-participants factor, each participant browsed both a standardized English-language Web site and a localized Web site. Results showed that animated (rather than static) banner ads, localized versions (rather than a standardized version) of Web sites, and high (rather than low) product involvement led to favorable attitudes toward the site.

Selecting International Standards for Accrual-Based Accounting in the Public Sector

DEFF Research Database (Denmark)

Pontoppidan, Caroline Aggestam

2011-01-01

The article discusses the definition of a government business enterprise (GBE), as provided in the International Public Sector Accounting Standards (IPSAS), as a determinant for applying IPSAS or the International Financial Reporting Standards (IFRS) for a public sector entity. The work...... of the IPSASB is focused on the accounting and financial reporting needs of national, regional and local governments, and related governmental agencies, while the IFRS serves the private sector....

Urban-hazard risk analysis: mapping of heat-related risks in the elderly in major Italian cities.

Science.gov (United States)

Morabito, Marco; Crisci, Alfonso; Gioli, Beniamino; Gualtieri, Giovanni; Toscano, Piero; Di Stefano, Valentina; Orlandini, Simone; Gensini, Gian Franco

2015-01-01

Short-term impacts of high temperatures on the elderly are well known. Even though Italy has the highest proportion of elderly citizens in Europe, there is a lack of information on spatial heat-related elderly risks. Development of high-resolution, heat-related urban risk maps regarding the elderly population (≥ 65). A long time-series (2001-2013) of remote sensing MODIS data, averaged over the summer period for eleven major Italian cities, were downscaled to obtain high spatial resolution (100 m) daytime and night-time land surface temperatures (LST). LST was estimated pixel-wise by applying two statistical model approaches: 1) the Linear Regression Model (LRM); 2) the Generalized Additive Model (GAM). Total and elderly population density data were extracted from the Joint Research Centre population grid (100 m) from the 2001 census (Eurostat source), and processed together using "Crichton's Risk Triangle" hazard-risk methodology for obtaining a Heat-related Elderly Risk Index (HERI). The GAM procedure allowed for improved daytime and night-time LST estimations compared to the LRM approach. High-resolution maps of daytime and night-time HERI levels were developed for inland and coastal cities. Urban areas with the hazardous HERI level (very high risk) were not necessarily characterized by the highest temperatures. The hazardous HERI level was generally localized to encompass the city-centre in inland cities and the inner area in coastal cities. The two most dangerous HERI levels were greater in the coastal rather than inland cities. This study shows the great potential of combining geospatial technologies and spatial demographic characteristics within a simple and flexible framework in order to provide high-resolution urban mapping of daytime and night-time HERI. In this way, potential areas for intervention are immediately identified with up-to-street level details. This information could support public health operators and facilitate coordination for heat

Urban-hazard risk analysis: mapping of heat-related risks in the elderly in major Italian cities.

Directory of Open Access Journals (Sweden)

Marco Morabito

Full Text Available Short-term impacts of high temperatures on the elderly are well known. Even though Italy has the highest proportion of elderly citizens in Europe, there is a lack of information on spatial heat-related elderly risks.Development of high-resolution, heat-related urban risk maps regarding the elderly population (≥ 65.A long time-series (2001-2013 of remote sensing MODIS data, averaged over the summer period for eleven major Italian cities, were downscaled to obtain high spatial resolution (100 m daytime and night-time land surface temperatures (LST. LST was estimated pixel-wise by applying two statistical model approaches: 1 the Linear Regression Model (LRM; 2 the Generalized Additive Model (GAM. Total and elderly population density data were extracted from the Joint Research Centre population grid (100 m from the 2001 census (Eurostat source, and processed together using "Crichton's Risk Triangle" hazard-risk methodology for obtaining a Heat-related Elderly Risk Index (HERI.The GAM procedure allowed for improved daytime and night-time LST estimations compared to the LRM approach. High-resolution maps of daytime and night-time HERI levels were developed for inland and coastal cities. Urban areas with the hazardous HERI level (very high risk were not necessarily characterized by the highest temperatures. The hazardous HERI level was generally localized to encompass the city-centre in inland cities and the inner area in coastal cities. The two most dangerous HERI levels were greater in the coastal rather than inland cities.This study shows the great potential of combining geospatial technologies and spatial demographic characteristics within a simple and flexible framework in order to provide high-resolution urban mapping of daytime and night-time HERI. In this way, potential areas for intervention are immediately identified with up-to-street level details. This information could support public health operators and facilitate coordination for heat

EFT for Vortices with Dilaton-dependent Localized Flux

CERN Document Server

Burgess, C P; Williams, M

2015-01-01

We study how codimension-two objects like vortices back-react gravitationally with their environment in theories (such as 4D or higher-dimensional supergravity) where the bulk is described by a dilaton-Maxwell-Einstein system. We do so both in the full theory, for which the vortex is an explicit classical `fat brane' solution, and in the effective theory of `point branes' appropriate when the vortices are much smaller than the scales of interest for their back-reaction (such as the transverse Kaluza-Klein scale). We extend the standard Nambu-Goto description to include the physics of flux-localization wherein the ambient flux of the external Maxwell field becomes partially localized to the vortex, generalizing the results of a companion paper to include dilaton-dependence for the tension and localized flux. In the effective theory, such flux-localization is described by the next-to-leading effective interaction, and the boundary conditions to which it gives rise are known to play an important role in how (and...

Mapping Surface Heat Fluxes by Assimilating SMAP Soil Moisture and GOES Land Surface Temperature Data

Science.gov (United States)

Lu, Yang; Steele-Dunne, Susan C.; Farhadi, Leila; van de Giesen, Nick

2017-12-01

Surface heat fluxes play a crucial role in the surface energy and water balance. In situ measurements are costly and difficult, and large-scale flux mapping is hindered by surface heterogeneity. Previous studies have demonstrated that surface heat fluxes can be estimated by assimilating land surface temperature (LST) and soil moisture to determine two key parameters: a neutral bulk heat transfer coefficient (CHN) and an evaporative fraction (EF). Here a methodology is proposed to estimate surface heat fluxes by assimilating Soil Moisture Active Passive (SMAP) soil moisture data and Geostationary Operational Environmental Satellite (GOES) LST data into a dual-source (DS) model using a hybrid particle assimilation strategy. SMAP soil moisture data are assimilated using a particle filter (PF), and GOES LST data are assimilated using an adaptive particle batch smoother (APBS) to account for the large gap in the spatial and temporal resolution. The methodology is implemented in an area in the U.S. Southern Great Plains. Assessment against in situ observations suggests that soil moisture and LST estimates are in better agreement with observations after assimilation. The RMSD for 30 min (daytime) flux estimates is reduced by 6.3% (8.7%) and 31.6% (37%) for H and LE on average. Comparison against a LST-only and a soil moisture-only assimilation case suggests that despite the coarse resolution, assimilating SMAP soil moisture data is not only beneficial but also crucial for successful and robust flux estimation, particularly when the uncertainties in the model estimates are large.

Diurnal Cycles of High Resolution Land Surface Temperatures (LSTs) Determined from UAV Platforms Across a Range of Surface Types

Science.gov (United States)

McCabe, M.; Rosas Aguilar, J.; Parkes, S. D.; Aragon, B.

2017-12-01

Observation of land surface temperature (LST) has many practical uses, from studying boundary layer dynamics and land-atmosphere coupling, to investigating surface properties such as soil moisture status, heat stress and surface heat fluxes. Typically, LST is observed via satellite based sensors such as LandSat or via point measurements using IR radiometers. These measurements provide either good spatial coverage and resolution or good temporal coverage. However, neither are able to provide the needed spatial and temporal resolution for many of the research applications described above. Technological developments in the use of Unmanned Aerial Vehicles (UAVs), together with small thermal frame cameras, has enabled a capacity to overcome this spatiotemporal constraint. Utilising UAV platforms to collect LST measurements across diurnal cycles provides an opportunity to study how meteorological and surface properties vary in both space and time. Here we describe the collection of LST data from a multi-rotor UAV across a study domain that is observed multiple times throughout the day. Flights over crops of Rhodes grass and alfalfa, along with a bare desert surface, were repeated with between 8 and 11 surveys covering the period from early morning to sunset. Analysis of the collected thermal imagery shows that the constructed LST maps illustrate a strong diurnal cycle consistent with expected trends, but with considerable spatial and temporal variability observed within and between the different domains. These results offer new insights into the dynamics of land surface behavior in both dry and wet soil conditions and at spatiotemporal scales that are unable to be replicated using traditional satellite platforms.

THE EFFECT OF LAND USE CHANGE ON LAND SURFACE TEMPERATURE IN THE NETHERLANDS

Directory of Open Access Journals (Sweden)

S. Youneszadeh

2015-12-01

Full Text Available The Netherlands is a small country with a relatively large population which experienced a rapid rate of land use changes from 2000 to 2008 years due to the industrialization and population increase. Land use change is especially related to the urban expansion and open agriculture reduction due to the enhanced economic growth. This research reports an investigation into the application of remote sensing and geographical information system (GIS in combination with statistical methods to provide a quantitative information on the effect of land use change on the land surface temperature. In this study, remote sensing techniques were used to retrieve the land surface temperature (LST by using the MODIS Terra (MOD11A2 Satellite imagery product. As land use change alters the thermal environment, the land surface temperature (LST could be a proper change indicator to show the thermal changes in relation with land use changes. The Geographical information system was further applied to extract the mean yearly land surface temperature (LST for each land use type and each province in the 2003, 2006 and 2008 years, by using the zonal statistic techniques. The results show that, the inland water and offshore area has the highest night land surface temperature (LST. Furthermore, the Zued (South-Holland province has the highest night LST value in the 2003, 2006 and 2008 years. The result of this research will be helpful tool for urban planners and environmental scientists by providing the critical information about the land surface temperature.

An Improved Single-Channel Method to Retrieve Land Surface Temperature from the Landsat-8 Thermal Band

Directory of Open Access Journals (Sweden)

Jordi Cristóbal

2018-03-01

Full Text Available Land surface temperature (LST is one of the sources of input data for modeling land surface processes. The Landsat satellite series is the only operational mission with more than 30 years of archived thermal infrared imagery from which we can retrieve LST. Unfortunately, stray light artifacts were observed in Landsat-8 TIRS data, mostly affecting Band 11, currently making the split-window technique impractical for retrieving surface temperature without requiring atmospheric data. In this study, a single-channel methodology to retrieve surface temperature from Landsat TM and ETM+ was improved to retrieve LST from Landsat-8 TIRS Band 10 using near-surface air temperature (Ta and integrated atmospheric column water vapor (w as input data. This improved methodology was parameterized and successfully evaluated with simulated data from a global and robust radiosonde database and validated with in situ data from four flux tower sites under different types of vegetation and snow cover in 44 Landsat-8 scenes. Evaluation results using simulated data showed that the inclusion of Ta together with w within a single-channel scheme improves LST retrieval, yielding lower errors and less bias than models based only on w. The new proposed LST retrieval model, developed with both w and Ta, yielded overall errors on the order of 1 K and a bias of −0.5 K validated against in situ data, providing a better performance than other models parameterized using w and Ta or only w models that yielded higher error and bias.

Paving the Way for Heat. Local Government Policies for Developing Bioenergy

Directory of Open Access Journals (Sweden)

Bente Johnsen Rygg

2014-06-01

Full Text Available Local governments play dual roles in developing renewable energy projects. They are the targets of many goals concerning energy and climate, set by national and international actors, and they are important actors in energy planning, regulation setting, and the development of infrastructure and residential areas. In this paper, I study how local governments’ technology policies affect the actual outcome of project development based on experiences from 14 local governments. Technology policies are studied from the perspective of Sørensen’s [1] four areas of concern: direct support of innovation, infrastructure, regulation (protection and standards and public engagement. I find that local governments use policy instruments within all four areas, and that the way local governments involves in the process of bioenergy development are surprisingly similar despite differences in location and size of both the local government and the project.

Moving beyond Compliance: Promoting Research-Based Professional Discretion in the Implementation of the Common Core State Standards in English Language Arts

Science.gov (United States)

Woodard, Rebecca; Kline, Sonia

2015-01-01

State- and local-level mandates are currently being implemented to ensure strict compliance to the new national Common Core State Standards for English Language Arts (CCSS for ELA) and related assessments. These standards provide many potential opportunities to improve literacy education nationally and locally. However, the CCSS for ELA will…

Local bone graft harvesting and volumes in posterolateral lumbar fusion: a technical report.

Science.gov (United States)

Carragee, Eugene J; Comer, Garet C; Smith, Micah W

2011-06-01

In lumbar surgery, local bone graft is often harvested and used in posterolateral fusion procedures. The volume of local bone graft available for posterolateral fusion has not been determined in North American patients. Some authors have described this as minimal, but others have suggested the volume was sufficient to be reliably used as a stand-alone bone graft substitute for single-level fusion. To describe the technique used and determine the volume of local bone graft available in a cohort of patients undergoing single-level primary posterolateral fusion by the authors harvesting technique. Technical description and cohort report. Consecutive patients undergoing lumbar posterolateral fusion with or without instrumentation for degenerative processes. Local bone graft volume. Consecutive patients undergoing lumbar posterolateral fusion with or without instrumentation for degenerative processes of were studied. Local bone graft was harvested by a standard method in each patient and the volume measured by a standard procedure. Twenty-five patients were studied, and of these 11 (44%) had a previous decompression. The mean volume of local bone graft harvested was measured to be 25 cc (range, 12-36 cc). Local bone graft was augmented by iliac crest bone in six of 25 patients (24%) if the posterolateral fusion bed was not well packed with local bone alone. There was a trend to greater local bone graft volumes in men and in patients without previous decompression. Large volumes of local bone can be harvested during posterolateral lumbar fusion surgery. Even in patients with previous decompression the volume harvested is similar to that reported harvested from the posterior iliac crest for single-level fusion. Copyright © 2011 Elsevier Inc. All rights reserved.

Localization--the revolution in consumer markets.

Science.gov (United States)

Rigby, Darrell K; Vishwanath, Vijay

2006-04-01

Standardization has been a powerful strategy in consumer markets, but it's reached the point of diminishing returns. And diversity is not the only chink in standardization's armor: Attempts to build stores in the remaining attractive locations often meet fierce resistance from community activists. From California to Florida to New Jersey, neighborhoods are passing ordinances that dictate the sizes and even architectural styles of new shops. Building more of the same--long the cornerstone of retailer growth--seems to be tapped out as a strategy. Of course, a company can't customize every element of its business in every location. Strategists have begun to use clustering techniques to simplify and smooth out decision making and to focus their efforts on the relatively small number of variables that usually drive the bulk of consumer purchases. The customization-by-clusters approach, which began as a strategy for grocery stores in 1995, has since proven effective in drugstores, department stores, mass merchants, big-box retailers, restaurants, apparel companies, and a variety of consumer goods manufacturers. Clustering sorts things into groups, so that the associations are strong between members of the same cluster and weak between members of different clusters. In fact, by centralizing data-intensive and scale-sensitive functions (such as store design, merchandise assortment, buying, and supply chain management), localization liberates store personnel to do what they do best: Test innovative solutions to local challenges and forge strong bonds with communities. Ultimately, all companies serving consumers will face the challenge of local customization. We are advancing to a world where the strategies of the most successful businesses will be as diverse as the communities they serve.

Dose-Effect Relationship in Chemoradiotherapy for Locally Advanced Rectal Cancer

DEFF Research Database (Denmark)

Jakobsen, Anders; Ploen, John; Vuong, Té

2012-01-01

PURPOSE: Locally advanced rectal cancer represents a major therapeutic challenge. Preoperative chemoradiation therapy is considered standard, but little is known about the dose-effect relationship. The present study represents a dose-escalation phase III trial comparing 2 doses of radiation...

Gauge unification, non-local breaking, open strings

International Nuclear Information System (INIS)

Trapletti, M.

2005-01-01

The issue of non-local GUT symmetry breaking is addressed in the context of open string model building. We study Z N xZ M ' orbifolds with all the GUT-breaking orbifold elements acting freely, as rotations accompanied by translations in the internal space. We consider open strings quantized on these backgrounds, distinguishing whether the translational action is parallel or perpendicular to the D-branes. GUT breaking is impossible in the purely perpendicular case, non-local GUT breaking is instead allowed in the purely parallel case. In the latter, the scale of breaking is set by the compactification moduli, and there are no fixed points with reduced gauge symmetry, where dangerous explicit GUT-breaking terms could be located. We investigate the mixed parallel+perpendicular case in a Z 2 xZ 2 ' example, having also a simplified field theory realization. It is a new S 1 /Z 2 xZ 2 ' orbifold-GUT model, with bulk gauge symmetry SU(5)xSU(5) broken locally to the Standard Model gauge group. In spite of the locality of the GUT symmetry breaking, there is no localized contribution to the running of the coupling constants, and the unification scale is completely set by the length of S 1

Airborne black carbon concentrations over an urban region in western India-temporal variability, effects of meteorology, and source regions.

Science.gov (United States)

Bapna, Mukund; Sunder Raman, Ramya; Ramachandran, S; Rajesh, T A

2013-03-01

This study characterizes over 5 years of high time resolution (5 min), airborne black carbon (BC) concentrations (July 2003 to December 2008) measured over Ahmedabad, an urban region in western India. The data were used to obtain different time averages of BC concentrations, and these averages were then used to assess the diurnal, seasonal, and annual variability of BC over the study region. Assessment of diurnal variations revealed a strong association between BC concentrations and vehicular traffic. Peaks in BC concentration were co-incident with the morning (0730 to 0830, LST) and late evening (1930 to 2030, LST) rush hour traffic. Additionally, diurnal variability in BC concentrations during major festivals (Diwali and Dushera during the months of October/November) revealed an increase in BC concentrations due to fireworks displays. Maximum half hourly BC concentrations during the festival days were as high as 79.8 μg m(-3). However, the high concentrations rapidly decayed suggesting that local meteorology during the festive season was favorable for aerosol dispersion. A multiple linear regression (MLR) model with BC as the dependent variable and meteorological parameters as independent variables was fitted. The variability in temperature, humidity, wind speed, and wind direction accounted for about 49% of the variability in measured BC concentrations. Conditional probability function (CPF) analysis was used to identify the geographical location of local source regions contributing to the effective BC measured (at 880 nm) at the receptor site. The east north-east (ENE) direction to the receptor was identified as a major source region. National highway (NH8) and two coal-fired thermal power stations (at Gandhinagar and Sabarmati) were located in the identified direction, suggesting that local traffic and power plant emissions were likely contributors to the measured BC.

The New York Head-A precise standardized volume conductor model for EEG source localization and tES targeting.

Science.gov (United States)

Huang, Yu; Parra, Lucas C; Haufe, Stefan

2016-10-15

In source localization of electroencephalograpic (EEG) signals, as well as in targeted transcranial electric current stimulation (tES), a volume conductor model is required to describe the flow of electric currents in the head. Boundary element models (BEM) can be readily computed to represent major tissue compartments, but cannot encode detailed anatomical information within compartments. Finite element models (FEM) can capture more tissue types and intricate anatomical structures, but with the higher precision also comes the need for semi-automated segmentation, and a higher computational cost. In either case, adjusting to the individual human anatomy requires costly magnetic resonance imaging (MRI), and thus head modeling is often based on the anatomy of an 'arbitrary' individual (e.g. Colin27). Additionally, existing reference models for the human head often do not include the cerebro-spinal fluid (CSF), and their field of view excludes portions of the head and neck-two factors that demonstrably affect current-flow patterns. Here we present a highly detailed FEM, which we call ICBM-NY, or "New York Head". It is based on the ICBM152 anatomical template (a non-linear average of the MRI of 152 adult human brains) defined in MNI coordinates, for which we extended the field of view to the neck and performed a detailed segmentation of six tissue types (scalp, skull, CSF, gray matter, white matter, air cavities) at 0.5mm(3) resolution. The model was solved for 231 electrode locations. To evaluate its performance, additional FEMs and BEMs were constructed for four individual subjects. Each of the four individual FEMs (regarded as the 'ground truth') is compared to its BEM counterpart, the ICBM-NY, a BEM of the ICBM anatomy, an 'individualized' BEM of the ICBM anatomy warped to the individual head surface, and FEMs of the other individuals. Performance is measured in terms of EEG source localization and tES targeting errors. Results show that the ICBM-NY outperforms

Development on advanced technology of local dosimetry for various radiation sources

International Nuclear Information System (INIS)

Odano, Naoteru; Ohnishi, Seiki; Ueki, Kohtaro

2004-01-01

The development aims at measuring local dose distribution accurately and handy and at enhancing precision of dose evaluation, so that personnel exposure can be reduced. A sheet type device and a sheet data reader were produced for trial and their performance testing were made under Sr-90 standard radiation and synchrotron radiation sources. Also a computer code was developed to analyze two-dimensional local dose distribution and to evaluate the precision of the sheet type dosimeter and data reader. The code enables to calculate local exposure doses of phantom quickly and simply for various beam irradiation conditions. (H. Yokoo)

Guidelines for standard and biuretic renogram in children

International Nuclear Information System (INIS)

Gordon, I.; Piepsz, A.; Colarinha, P.; Hahn, K.; Fischer, S.; Porn, U.; Sixt, R.; Velzen, J. van

2000-01-01

The guidelines are intended to help nuclear medical teams in their daily routine. The information given relates to aspects such as data acquisition, evaluation and interpretation, and indications for pediatric renal functional scintigraphy. The guidelines have been elaborated in response to a request of EANM and the American Society of Nuclear Medicine, who expressed the need for guidelines on recommended procedures for most of the standard nuclear medical examinations. The guidelines express the opinion of the Paediatric Committee of the EANM, and should be seen in the context of generally accepted basic principles in nuclear medicine, as well as local and national regulatory standards in radiation protection. (orig./CB) [de

Global, National, and Local Goals: English Language Policy Implementation in an Indonesian International Standard School

Directory of Open Access Journals (Sweden)

Eddy Haryanto

2012-12-01

Full Text Available The purpose of this study was to examine the achievement of students in math and science subjects as the impact of using English as a medium of instruction at an international standard school. A questionnaire was used as a research instrument to 190 students at one international standard school in Jambi Province, Indonesia. A focus group discussion (FGD approach was undertaken to validate and verify the data gathered through the questionnaire and clarify some issues raised in the questionnaire. Data were analyzed by using descriptive statistics and Pearson Product Moment Correlation. It was found that the students’ demographic profile, attitude toward English and grades in math and science subjects were significantly related with their academic achievement. However, students’ perception on methods and techniques was not significantly related with their academic achievement in English, math, and the science subjects. The result showed that the implementation of English as a medium of instruction was not done well in the international standard school. This is perhaps due to the difficulty of learning science and math in English. This study provided information for policy makers, school leaders, researchers, and teacher educators to understand how the policy is implemented at the school level. The challenges of attempting too ambitious linguistic and academic goals in the school were discussed as were policy implications and future research.

Chaos-assisted tunneling in the presence of Anderson localization.

Science.gov (United States)

Doggen, Elmer V H; Georgeot, Bertrand; Lemarié, Gabriel

2017-10-01

Tunneling between two classically disconnected regular regions can be strongly affected by the presence of a chaotic sea in between. This phenomenon, known as chaos-assisted tunneling, gives rise to large fluctuations of the tunneling rate. Here we study chaos-assisted tunneling in the presence of Anderson localization effects in the chaotic sea. Our results show that the standard tunneling rate distribution is strongly modified by localization, going from the Cauchy distribution in the ergodic regime to a log-normal distribution in the strongly localized case, for both a deterministic and a disordered model. We develop a single-parameter scaling description which accurately describes the numerical data. Several possible experimental implementations using cold atoms, photonic lattices, or microwave billiards are discussed.

Genetic structure among the local chicken ecotypes of Tanzania ...

African Journals Online (AJOL)

A study was conducted to evaluate the genetic structure of local chicken ecotypes of Tanzania using 20 polymorphic microsatellite DNA markers. A standard PCR was followed by manual genotyping (6% native polyacrylamide gel visualized by silver staining). Phylogenetic analysis of 13 individuals from each of the nine ...

A Comparison of Flood Control Standards for Reservoir Engineering for Different Countries

Directory of Open Access Journals (Sweden)

Minglei Ren

2017-02-01

Full Text Available Across the globe, flood control standards for reservoir engineering appear different due to various deciding factors such as flood features, society, economy, culture, morality, politics, and technology resources, etc. This study introduces an in-depth comparison of flood control standards for reservoir engineering for different countries. After the comparison and analysis, it is concluded that the determination of flood control standards is related to engineering grade, dam type, dam height, and the hazard to downstream after dam-breaking, etc. Each country should adopt practical flood control standards according to the characteristics of local reservoir engineering. The constitutive flood control standards should retain certain flexibility in the basis of constraint force. This review could offer a reference for developing countries in the enactment of flood control standards for reservoir engineering.

Hypothermic general cold adaptation induced by local cold acclimation.

Science.gov (United States)

Savourey, G; Barnavol, B; Caravel, J P; Feuerstein, C; Bittel, J H

1996-01-01

To study relationships between local cold adaptation of the lower limbs and general cold adaptation, eight subjects were submitted both to a cold foot test (CFT, 5 degrees C water immersion, 5 min) and to a whole-body standard cold air test (SCAT, 1 degree C, 2 h, nude at rest) before and after a local cold acclimation (LCA) of the lower limbs effected by repeated cold water immersions. The LCA induced a local cold adaptation confirmed by higher skin temperatures of the lower limbs during CFT and a hypothermic insulative general cold adaptation (decreased rectal temperature and mean skin temperature P adaptation was related to the habituation process confirmed by decreased plasma concentrations of noradrenaline (NA) during LCA (P general cold adaptation was unrelated either to local cold adaptation or to the habituation process, because an increased NA during SCAT after LCA (P syndrome" occurring during LCA.

Local discrete symmetries from superstring derived models

International Nuclear Information System (INIS)

Faraggi, A.E.

1996-10-01

Discrete and global symmetries play an essential role in many extensions of the Standard Model, for example, to preserve the proton lifetime, to prevent flavor changing neutral currents, etc. An important question is how can such symmetries survive in a theory of quantum gravity, like superstring theory. In a specific string model the author illustrates how local discrete symmetries may arise in string models and play an important role in preventing fast proton decay and flavor changing neutral currents. The local discrete symmetry arises due to the breaking of the non-Abelian gauge symmetries by Wilson lines in the superstring models and forbids, for example dimension five operators which mediate rapid proton decay, to all orders of nonrenormalizable terms. In the context of models of unification of the gauge and gravitational interactions, it is precisely this type of local discrete symmetries that must be found in order to insure that a given model is not in conflict with experimental observations

Local land-atmosphere feedbacks limit irrigation demand

Science.gov (United States)

Decker, Mark; Ma, Shaoxiu; Pitman, Andy

2017-05-01

Irrigation is known to influence regional climate but most studies forecast and simulate irrigation with offline (i.e. land only) models. Using south eastern Australia as a test bed, we demonstrate that irrigation demand is fundamentally different between land only and land-atmosphere simulations. While irrigation only has a small impact on maximum temperature, the semi-arid environment experiences near surface moistening in coupled simulations over the irrigated regions, a feedback that is prevented in offline simulations. In land only simulations that neglect the local feedbacks, the simulated irrigation demand is 25% higher and the standard deviation of the mean irrigation rate is 60% smaller. These local-scale irrigation-driven feedbacks are not resolved in coarse-resolution climate models implying that use of these tools will overestimate irrigation demand. Future studies of irrigation demand must therefore account for the local land-atmosphere interactions by using coupled frameworks, at a spatial resolution that captures the key feedbacks.

Interaction and activity coordination of territorial customs bodies of the State fiscal service of Ukraine with local state administrations and local self-government bodies

Directory of Open Access Journals (Sweden)

Олексій Павлович Федотов

2016-06-01

Based on the results of the study the author notes that the interaction of the Ukrainian SFS customs offices and local state administrations with local self-government bodies is an inherent quality, link and component of the Ukrainian SFS Customs offices functioning organization, which aims to improve the state customs service implementation standards by the Ukrainian SFS customs houses and to ensure the said implementation efficiency. However, in the course of interaction of the Ukrainian SFS customs with local state administrations and local self-government bodies each of the mentioned organizations specializes in solving their specific tasks in accordance with their subject expertise, and forms a clear organizational system. The complementarity of such kind helps to improve the state customs affairs conductance quality and is realized through the coordination of performance of the Ukrainian SFS customs offices, local state administrations and local self-government bodies as the interaction subjects through normative, informational and analytical provision for the interaction and concretization of the activities of each subject within the planned activities.

Improved Main Shaft Seal Life in Gas Turbines Using Laser Surface Texturing

Science.gov (United States)

McNickle, Alan D.; Etsion, Izhak

2002-10-01

This paper presents a general overview of the improved main shaft seal life in gas turbines using laser surface texturing (LST). The contents include: 1) Laser Surface Texturing System; 2) Seal Schematic with LST applied; 3) Dynamic Rig Tests; 4) Surface Finish Definitions; 5) Wear Test Rig; 6) Dynamic Test Rig; 7) Seal Cross Section-Rig Test; and 8) Typical Test Results. This paper is in viewgraph form.

Nontraditional Intelligence, Surveillance, and Reconnaissance: Making the Most of Airborne Assets

Science.gov (United States)

2015-10-01

on its targeting pod. The laser spot search (LSS) and laser spot tracker (LST) functions allow one air- craft to essentially drag the other...detection and ranging LNO liaison officer LOC line of communications LRIP low-rate initial production LSS laser spot search LST laser spot tracker NGA...other aircraft and the ground com- mander during night operations, as well. Its onboard laser allows the air- craft to obtain highly accurate

Analysis of Windward Side Hypersonic Boundary Layer Transition on Blunted Cones at Angle of Attack

Science.gov (United States)

2017-01-09

correlated with PSE/LST N-Factors. 15. SUBJECT TERMS boundary layer transition, hypersonic, ground test 16. SECURITY CLASSIFICATION OF: 17. LIMITATION ...Maccoll) solution e condition at boundary layer edge w condition at wall, viscous ∞ condition in freestream Conventions LST Linear Stability Theory PSE...STATES AIR FORCE AFRL-RQ-WP-TP-2017-0169 ANALYSIS OF WINDWARD SIDE HYPERSONIC BOUNDARY LAYER TRANSITION ON BLUNTED CONES AT ANGLE OF ATTACK Roger

LOCAL IDENTITY MEETING WITH CITY: CITTASLOW-SLOW CITIES

Directory of Open Access Journals (Sweden)

Tugba Ustun Topal

2016-09-01

Full Text Available Cities are characterised by local identities, which have been shaped by natural and cultural values. Constituting elements of local identity are settlement pattern bearing the traces of past, local music, traditional taste, handicrafts and life story. Besides, there has been a fast pace of life owing to globalization, and globally standardized cities, where local identities are ignored, have been emerged in planning-design-implementation process. From this viewpoint, Cittaslow movement has become a major turning point for liveable and sustainable cities that emphasize the local character. In this context, in the study, it is aimed to raise awareness about Cittaslow which is an example of an urban model for sustainability. In line with this purpose, the importance of Cittaslow approach and the criteria that are needed to be met for being a member of the Association of Cittaslow have been revealed. In line with these criteria Cittaslow cities in Turkey were discussed comparatively in terms of their features were considered. Examples from our country have been evaluated together with the international Cittaslow examples. In addition, proposals have been made by developing strategies in planning- designing and implementation process for the Cittaslow approach.

Special Education Professional Standards: How Important Are They in the Context of Teacher Performance Evaluation?

Science.gov (United States)

Woolf, Sara B.

2015-01-01

Teacher performance evaluation represents a high stakes issue as evidenced by its pivotal emphasis in national and local education reform initiatives and federal policy levers. National, state, and local education leaders continue to experience unprecedented pressure to adopt standardized benchmarks to reflect and link student achievement data to…

Statistical density modification using local pattern matching

International Nuclear Information System (INIS)

Terwilliger, Thomas C.

2003-01-01

Statistical density modification can make use of local patterns of density found in protein structures to improve crystallographic phases. A method for improving crystallographic phases is presented that is based on the preferential occurrence of certain local patterns of electron density in macromolecular electron-density maps. The method focuses on the relationship between the value of electron density at a point in the map and the pattern of density surrounding this point. Patterns of density that can be superimposed by rotation about the central point are considered equivalent. Standard templates are created from experimental or model electron-density maps by clustering and averaging local patterns of electron density. The clustering is based on correlation coefficients after rotation to maximize the correlation. Experimental or model maps are also used to create histograms relating the value of electron density at the central point to the correlation coefficient of the density surrounding this point with each member of the set of standard patterns. These histograms are then used to estimate the electron density at each point in a new experimental electron-density map using the pattern of electron density at points surrounding that point and the correlation coefficient of this density to each of the set of standard templates, again after rotation to maximize the correlation. The method is strengthened by excluding any information from the point in question from both the templates and the local pattern of density in the calculation. A function based on the origin of the Patterson function is used to remove information about the electron density at the point in question from nearby electron density. This allows an estimation of the electron density at each point in a map, using only information from other points in the process. The resulting estimates of electron density are shown to have errors that are nearly independent of the errors in the original map using

Standardized uptake value on positron emission tomography/computed tomography predicts prognosis in patients with locally advanced pancreatic cancer.

Science.gov (United States)

Wang, Si-Liang; Cao, Shuo; Sun, Yu-Nan; Wu, Rong; Chi, Feng; Tang, Mei-Yue; Jin, Xue-Ying; Chen, Xiao-Dong

2015-10-01

The aim of the present study was to investigate the use and value of maximum standardized uptake value (SUV max) on positron emission tomography/computed tomography (PET/CT) images as a prognostic marker for patients with locally advanced pancreatic cancer (LAPC). The medical records of all consecutive patients who underwent PET/CT examination in our institution were retrospectively reviewed. Inclusion criteria were histologically or cytologically proven LAPC. Patients with distant metastasis were excluded. For statistical analysis, the SUV max of primary pancreatic cancer was measured. Survival rates were calculated using the Kaplan-Meier method, and multivariable analysis was performed to determine the association of SUV max with overall survival (OS) and progression-free survival (PFS) using a Cox proportional hazards model. Between July 2006 and June 2013, 69 patients were enrolled in the present study. OS and PFS were 14.9 months [95% confidence interval (CI) 13.1-16.7] and 8.3 months (95% CI 7.1-9.5), respectively. A high SUV max (>5.5) was observed in 35 patients, who had significantly worse OS and PFS than the remaining patients with a low SUV max (P = 0.025 and P = 0.003). Univariate analysis showed that SUV max and tumor size were prognostic factors for OS, with a hazard ratio of 1.90 and 1.81, respectively. A high SUV max was an independent prognostic factor, with a hazard ratio of 1.89 (95% CI 1.015-3.519, P = 0.045). The present study suggests that increased SUV max is a predictor of poor prognosis in patients with LAPC.

The National Expert Standard Pressure Ulcer Prevention in Nursing and pressure ulcer prevalence in German health care facilities: a multilevel analysis.

Science.gov (United States)

Wilborn, Doris; Grittner, Ulrike; Dassen, Theo; Kottner, Jan

2010-12-01

The objective of this study was to describe the relationship between the German National Expert Standard Pressure Ulcer Prevention and the pressure ulcer prevalence in German nursing homes and hospitals. The patient outcome pressure ulcer does not only depend on individual characteristics of patients, but also on institutional factors. In Germany, National Expert Standards are evidence-based instruments that build the basis of continuing improvement in health care quality. It is expected that after having implemented the National Expert Standard Pressure Ulcer Prevention, the number of pressure ulcers should decrease in health care institutions. The analysed data were obtained from two cross-sectional studies from 2004-2005. A multilevel analysis was performed to show the impact of the National Expert Standard Pressure Ulcer Prevention on pressure ulcer prevalence. A total of 41.5% of hospitals and 38.8% of the nursing homes claimed to use the National Expert Standard in the process of developing their local protocols. The overall pressure ulcer prevalence grade 2-4 was 4.7%. Adjusted for hospital departments, survey year and individual characteristics, there was no significant difference in the prevalence of pressure ulcers between institutions that refer to the National Expert Standard or those referring to other sources in developing their local protocols (OR=1.14, 95% CI=0.90-1.44). There was no empirical evidence demonstrating that local protocols of pressure ulcer prevention based on the National Expert Standard were superior to local protocols which refer other sources of knowledge with regard to the pressure ulcer prevalence. The use of the National Expert Standard Pressure Ulcer Prevention can neither be recommended nor be refused. The recent definition of implementation of Expert Standards should be mandatory for all health care institutions which introduce Expert Standards. © 2010 Blackwell Publishing Ltd.

Locally advanced cervix carcinoma - innovation in combined modality therapy

International Nuclear Information System (INIS)

Swift, Patrick S.

1996-01-01

Locally advanced cervical carcinoma continues to be a challenge to the clinician due to local failure as well as systemic metastases. Standard intracavitary and external beam techniques result in local control rates of only 35-65%, with long term survival rates of 25-60% in patients with state IIIA-IVA disease, indicating the need to identify new treatment strategies. Optimization programs for remote-afterloading interstitial brachytherapy allow the delivery of higher local doses of radiation to volumes that more closely approximate tumor target volumes as identified on MR scans, leading to improved therapeutic ratios. Identification of subsets of patients more likely to fail standard therapy, either locally or systemically, may be possible through such techniques as in vivo measurements of hypoxia with Eppendorf oxygen electrodes, interstitial fluid pressure measurements, the Comet assay, and nitroimidazole binding methods. Traditional chemotherapies, administered in either a neoadjuvant role or concomitantly with radiation have been disappointing in prospective trials. A variety of new agents are being investigated to determine if they can increase the frequency or duration of complete response. The taxanes, with response rates of 17-23% by themselves, are being assessed as potential radiosensitizers. The camptotheicin CRT-11 (Irinotecan) has demonstrated activity in platinum resistant cervix cancer, with response rates of 24%. Bioradiotherapeutic approaches, using 13-cis-retinoic acid and interferon-2a, are undergoing phase II studies. Neoangiogenesis inhibitors and vaccines against HPV are also being examined. The aggressive pursuit of techniques that help identify those patients most likely to fail, that allow the delivery of higher radiation doses more safely to the target volume, and that incorporate the use of more effective systemic therapies is necessary to improve the outcome for this disease

INVOLVEMENT OF LOCAL PUBLIC ADMINISTRATION ON THE DEVELOPMENT OF RURAL TOURISM

Directory of Open Access Journals (Sweden)

Ionel Barbu

2014-12-01

Full Text Available In this paper we try to show the perception of the main stakeholder on the rural tourism field, local government, on the development of this economic activities. We believe that a revision of an important part of approaches that have appeared in the literature in terms of the concept of rural tourism, in terms of methods of analysis of tourism activities and, not least, requiring the use modern techniques for foresight indicators by which to make assessments on these activities.The local public administration is responsible for policy formulation, research and planning, development of basic infrastructure, the development of certain landmarks, establishing and managing service delivery standards, establishing management measures and recovery planning and environmental protection, setting standards for training and improving employment, setting standards for maintaining public health and safety.In this paper we try to show as well the main factors of the emergence and development of rural tourism in order to establish priorities in the joint action of local people, entrepreneurs, tourists and local and national administrations. In many countries, the tourism industry fall within government priority. Tourism has been identified as one of the primary industries with potential to support local communities in developing economic diversity. In this research, it was also used descriptive analysis of the variables and comparative analysis using Kruskal-Wallis H and Mann-Whitney U test.Kruskal-Wallis H test. The Kruskall-Wallis test aims at comparing several independent samples when, as is the case of our research, the dependent variable is ordinal. The test is based on rank and hierarchy of data analysis. Scores are ranked from lowest to highest, ignoring the groups they belong to, and then calculate the sum of ranks for each of the groups. The question refers to how much respondents considered that are due to the development of rural tourism

Correlating Remote Sensing Data with the Abundance of Pupae of the Dengue Virus Mosquito Vector, Aedes aegypti, in Central Mexico

Directory of Open Access Journals (Sweden)

Max J. Moreno-Madriñán

2014-05-01

Full Text Available Using a geographic transect in Central Mexico, with an elevation/climate gradient, but uniformity in socio-economic conditions among study sites, this study evaluates the applicability of three widely-used remote sensing (RS products to link weather conditions with the local abundance of the dengue virus mosquito vector, Aedes aegypti (Ae. aegypti. Field-derived entomological measures included estimates for the percentage of premises with the presence of Ae. aegypti pupae and the abundance of Ae. aegypti pupae per premises. Data on mosquito abundance from field surveys were matched with RS data and analyzed for correlation. Daily daytime and nighttime land surface temperature (LST values were obtained from Moderate Resolution Imaging Spectroradiometer (MODIS/Aqua cloud-free images within the four weeks preceding the field survey. Tropical Rainfall Measuring Mission (TRMM-estimated rainfall accumulation was calculated for the four weeks preceding the field survey. Elevation was estimated through a digital elevation model (DEM. Strong correlations were found between mosquito abundance and RS-derived night LST, elevation and rainfall along the elevation/climate gradient. These findings show that RS data can be used to predict Ae. aegypti abundance, but further studies are needed to define the climatic and socio-economic conditions under which the correlations observed herein can be assumed to apply.

IMI's teaching design, feedback system and its localization

Science.gov (United States)

Wen, Tingting; Zhang, Xuexin

2017-08-01

In Britain, the Institute of the Motor Industry (IMI) sets the National Occupational Standards for all sectors of the automotive industry. The IMI certificate and associated training programs are well recognized for its high quality both in the United Kingdom (UK) and internationally. Using China's first groups studying IMI Level 3 certificate for teachers and Level 2 certificate for students as a sample, we analyzed the seven central aspects in IMI teaching, namely, assessment standard, environment, method, content, procedure, quality control and feedback. We then proposed strategies and guidelines for its localization in China, which would be particularly important for the establishment and expansion of IMI centers.

On the connection between quantum fields and von Neumann algebras of local operators

International Nuclear Information System (INIS)

Driessler, W.; Summers, S.J.; Wichmann, E.H.

1986-01-01

The relationship between a standard local quantum field and a net of local von Neumann algebras is discussed. Two natural possibilities for such an association are identified, and conditions for these to obtain are found. It is shown that the local net can naturally be so chosen that it satisfies the Special Condition of Duality. The notion of an intrinsically local field operator is introduced, and it is shown that such an operator defines a local net with which the field is locally associated. A regularity condition on the field is formulated, and it is shown that if this condition holds, then there exists a unique local net with which the field is locally associated if and only if the field algebra contains at least one intrinsically local operator. Conditions under which a field and other fields in its Borchers class are associated with the same local net are found, in terms of the regularity condition mentioned. (orig.)

Medial canthal reconstruction with multiple local flaps

Directory of Open Access Journals (Sweden)

Akihiro Ogino

2018-03-01

Conclusion: This method is somewhat complicated compared to reconstruction with a single flap, but it is a combination of standard local flaps and is a simple reconstructive procedure. By adding additional resection, the suture line is consistent with the border of the facial unit, so postoperative scarring is inconspicuous. This technique is aesthetically useful because of the continuity of colour and texture resulting from the use of adjacent flaps.

Requirements, Science, and Measurements for Landsat 10 and Beyond: Perspectives from the Landsat Science Team

Science.gov (United States)

Crawford, C. J.; Masek, J. G.; Roy, D. P.; Woodcock, C. E.; Wulder, M. A.

2017-12-01

The U.S. Geological Survey (USGS) and NASA are currently prioritizing requirements and investing in technology options for a "Landsat 10 and beyond" mission concept as part of the Sustainable Land Imaging (SLI) architecture. Following the successful February 2013 launch of the Landsat 8, the Operational Land Imager (OLI) and Thermal Infrared Sensor (TIRS) have now added over 1 million images to the USGS Landsat archive. The USGS and NASA support and co-lead a Landsat Science Team made up largely of university and government experts to offer independent insight and guidance of program activities and directions. The rapid development of Landsat 9 reflects, in part, strong input from the 2012-2017 USGS Landsat Science Team (LST). During the last two years of the LST's tenure, individual LST members and within LST team working groups have made significant contributions to Landsat 10 and beyond's science traceability and future requirements justification. Central to this input, has been an effort to identify a trade space for enhanced measurement capabilities that maintains mission continuity with eight prior multispectral instruments, and will extend the Landsat Earth observation record beyond 55+ years with an approximate launch date of 2027. The trade space is framed by four fundamental principles in remote sensing theory and practice: (1) temporal resolution, (2) spatial resolution, (3) radiometric resolution, and (4) spectral coverage and resolution. The goal of this communication is to provide a synopsis of past and present 2012-2017 LST contributions to Landsat 10 and beyond measurement science and application priorities. A particular focus will be to document the links between new science and societal benefit areas with potential technical enhancements to the Landsat mission.

Validation of three-dimensional incompressible spatial direct numerical simulation code: A comparison with linear stability and parabolic stability equation theories for boundary-layer transition on a flat plate

Science.gov (United States)

Joslin, Ronald D.; Streett, Craig L.; Chang, Chau-Lyan

1992-01-01

Spatially evolving instabilities in a boundary layer on a flat plate are computed by direct numerical simulation (DNS) of the incompressible Navier-Stokes equations. In a truncated physical domain, a nonstaggered mesh is used for the grid. A Chebyshev-collocation method is used normal to the wall; finite difference and compact difference methods are used in the streamwise direction; and a Fourier series is used in the spanwise direction. For time stepping, implicit Crank-Nicolson and explicit Runge-Kutta schemes are used to the time-splitting method. The influence-matrix technique is used to solve the pressure equation. At the outflow boundary, the buffer-domain technique is used to prevent convective wave reflection or upstream propagation of information from the boundary. Results of the DNS are compared with those from both linear stability theory (LST) and parabolized stability equation (PSE) theory. Computed disturbance amplitudes and phases are in very good agreement with those of LST (for small inflow disturbance amplitudes). A measure of the sensitivity of the inflow condition is demonstrated with both LST and PSE theory used to approximate inflows. Although the DNS numerics are very different than those of PSE theory, the results are in good agreement. A small discrepancy in the results that does occur is likely a result of the variation in PSE boundary condition treatment in the far field. Finally, a small-amplitude wave triad is forced at the inflow, and simulation results are compared with those of LST. Again, very good agreement is found between DNS and LST results for the 3-D simulations, the implication being that the disturbance amplitudes are sufficiently small that nonlinear interactions are negligible.

Quality of Online Chat Reference Answers Differ between Local and Consortium Library Staff: Providing Consortium Staff with More Local Information Can Mitigate these Differences. A Review of: Meert, D.L., & Given, L.M. (2009. Measuring quality in chat reference consortia: A comparative analysis of responses to users’ queries.” College & Research Libraries, 70(1, 71‐84.

Directory of Open Access Journals (Sweden)

Laura Newton Miller

2010-03-01

Full Text Available Objective – To evaluate the quality of answers from a 24/7 online chat reference service by comparing the responses given by local and consortia library staff using in‐house reference standards, and by assessing whether or not the questions were answered in real time.Design – Comparative analysis of online chat reference transcripts.Setting – Large academic library in Alberta, Canada.Subjects – A total of online chat reference transcripts from the first year of consortium service were analyzed for this study. Of these, 252 were answered by local library staff and 226 from consortia (non‐local library staff.Methods – A stratified random sample of 1,402 transcripts were collected from the first year of consortium service (beginning of October to end of April. This method was then applied monthly, resulting in a sample size of 478 transcripts. In the first part of the study, responses were coded within the transcripts with a “yes” or “no” label to determine if they met the standards set by the local university library’s reference management. Reference transaction standards included questions regarding whether or not correct information or instructions were given and if not, whether the user was referred to an authoritative source for the correct information. The second part of the study coded transcripts with a “yes” or “no” designation as to whether the user received an answer from the staff member in “real time” and if not, was further analyzed to determine why the user did not receive a real‐time response. Each transcript was coded as reflecting one of four “question categories” that included library user information, request for instruction, request for academic information, and miscellaneous/non‐library questions.Main Results – When all question types were integrated, analysis revealed that local library staff met reference transaction standards 94% of the time. Consortia staff met these same

Predicting the nutritional health status of locally produced palm oil ...

African Journals Online (AJOL)

Three physical properties of locally produced palm oil – viscosity, thermal conductivity and density for varying temperatures were determined. The values obtained were compared with corresponding internationally stipulated standard values using statistics of mean and graphs. The purpose of the comparison was to predict ...

Impact of Vegetation Cover Fraction Parameterization schemes on Land Surface Temperature Simulation in the Tibetan Plateau

Science.gov (United States)

Lv, M.; Li, C.; Lu, H.; Yang, K.; Chen, Y.

2017-12-01

The parameterization of vegetation cover fraction (VCF) is an important component of land surface models. This paper investigates the impacts of three VCF parameterization schemes on land surface temperature (LST) simulation by the Common Land Model (CoLM) in the Tibetan Plateau (TP). The first scheme is a simple land cover (LC) based method; the second one is based on remote sensing observation (hereafter named as RNVCF) , in which multi-year climatology VCFs is derived from Moderate-resolution Imaging Spectroradiometer (MODIS) NDVI (Normalized Difference Vegetation Index); the third VCF parameterization scheme derives VCF from the LAI simulated by LSM and clump index at every model time step (hereafter named as SMVCF). Simulated land surface temperature(LST) and soil temperature by CoLM with three VCF parameterization schemes were evaluated by using satellite LST observation and in situ soil temperature observation, respectively, during the period of 2010 to 2013. The comparison against MODIS Aqua LST indicates that (1) CTL produces large biases for both four seasons in early afternoon (about 13:30, local solar time), while the mean bias in spring reach to 12.14K; (2) RNVCF and SMVCF reduce the mean bias significantly, especially in spring as such reduce is about 6.5K. Surface soil temperature observed at 5 cm depth from three soil moisture and temperature monitoring networks is also employed to assess the skill of three VCF schemes. The three networks, crossing TP from West to East, have different climate and vegetation conditions. In the Ngari network, located in the Western TP with an arid climate, there are not obvious differences among three schemes. In Naqu network, located in central TP with a semi-arid climate condition, CTL shows a severe overestimates (12.1 K), but such overestimations can be reduced by 79% by RNVCF and 87% by SMVCF. In the third humid network (Maqu in eastern TP), CoLM performs similar to Naqu. However, at both Naqu and Maqu networks

Appraisal of Phlebotomus argentipes habitat suitability using a remotely sensed index in the kala-azar endemic focus of Bihar, India

Directory of Open Access Journals (Sweden)

Shreekant Kesari

2013-04-01

Full Text Available Visceral leishmaniasis, or kala-azar, is recognised as a serious emerging public health problem in India. In this study, environmental parameters, such as land surface temperature (LST and renormalised difference vegetation indices (RDVI, were used to delineate the association between environmental variables and Phlebotomus argentipes abundance in a representative endemic region of Bihar, India. The adult P. argentipes were collected between September 2009-February 2010 using the hand-held aspirator technique. The distribution of P. argentipes was analysed with the LST and RDVI of the peak and lean seasons. The association between environmental covariates and P. argentipes density was analysed a multivariate linear regression model. The sandfly density at its maximum in September, whereas the minimum density was recorded in January. The regression model indicated that the season, minimum LST, mean LST and mean RDVI were the best environmental covariates for the P. argentipes distribution. The final model indicated that nearly 74% of the variance of sandfly density could be explained by these environmental covariates. This approach might be useful for mapping and predicting the distribution of P. argentipes, which may help the health agencies that are involved in the kala-azar control programme focus on high-risk areas.

Land Surface Temperature and Emissivity Separation from Cross-Track Infrared Sounder Data with Atmospheric Reanalysis Data and ISSTES Algorithm

Directory of Open Access Journals (Sweden)

Yu-Ze Zhang

2017-01-01

Full Text Available The Cross-track Infrared Sounder (CrIS is one of the most advanced hyperspectral instruments and has been used for various atmospheric applications such as atmospheric retrievals and weather forecast modeling. However, because of the specific design purpose of CrIS, little attention has been paid to retrieving land surface parameters from CrIS data. To take full advantage of the rich spectral information in CrIS data to improve the land surface retrievals, particularly the acquisition of a continuous Land Surface Emissivity (LSE spectrum, this paper attempts to simultaneously retrieve a continuous LSE spectrum and the Land Surface Temperature (LST from CrIS data with the atmospheric reanalysis data and the Iterative Spectrally Smooth Temperature and Emissivity Separation (ISSTES algorithm. The results show that the accuracy of the retrieved LSEs and LST is comparable with the current land products. The overall differences of the LST and LSE retrievals are approximately 1.3 K and 1.48%, respectively. However, the LSEs in our study can be provided as a continuum spectrum instead of the single-channel values in traditional products. The retrieved LST and LSEs now can be better used to further analyze the surface properties or improve the retrieval of atmospheric parameters.

Impact of vegetation growth on urban surface temperature distribution

International Nuclear Information System (INIS)

Buyadi, S N A; Mohd, W M N W; Misni, A

2014-01-01

Earlier studies have indicated that, the temperature distribution in the urban area is significantly warmer than its surrounding suburban areas. The process of urbanization has created urban heat island (UHI). As a city expands, trees are cut down to accommodate commercial development, industrial areas, roads, and suburban growth. Trees or green areas normally play a vital role in mitigating the UHI effects especially in regulating high temperature in saturated urban areas. This study attempts to assess the effects of vegetation growth on land surface temperature (LST) distribution in urban areas. An area within the City of Shah Alam, Selangor has been selected as the study area. Land use/land cover and LST maps of two different dates are generated from Landsat 5 TM images of the year 1991 and 2009. Only five major land cover classes are considered in this study. Mono-window algorithm is used to generate the LST maps. Landsat 5 TM images are also used to generate the NDVI maps. Results from this study have shown that there are significant land use changes within the study area. Although the conversion of green areas into residential and commercial areas significantly increase the LST, matured trees will help to mitigate the effects of UHI

Study on cavitation effect of mechanical seals with laser-textured porous surface

Science.gov (United States)

Liu, T.; Chen, H. l.; Liu, Y. H.; Wang, Q.; Liu, Z. B.; Hou, D. H.

2012-11-01

Study on the mechanisms underlying generation of hydrodynamic pressure effect associated with laser-textured porous surface on mechanical seal, is the key to seal and lubricant properties. The theory model of mechanical seals with laser-textured porous surface (LES-MS) based on cavitation model was established. The LST-MS was calculated and analyzed by using Fluent software with full cavitation model and non-cavitation model and film thickness was predicted by the dynamic mesh technique. The results indicate that the effect of hydrodynamic pressure and cavitation are the important reasons to generate liquid film opening force on LST-MS; Cavitation effect can enhance hydrodynamic pressure effect of LST-MS; The thickness of liquid film could be well predicted with the method of dynamic mesh technique on Fluent and it becomes larger as the increasing of shaft speed and the decreasing of pressure.

Study on cavitation effect of mechanical seals with laser-textured porous surface

International Nuclear Information System (INIS)

Liu, T; Chen, H l; Liu, Y H; Wang, Q; Liu, Z B; Hou, D H

2012-01-01

Study on the mechanisms underlying generation of hydrodynamic pressure effect associated with laser-textured porous surface on mechanical seal, is the key to seal and lubricant properties. The theory model of mechanical seals with laser-textured porous surface (LES-MS) based on cavitation model was established. The LST-MS was calculated and analyzed by using Fluent software with full cavitation model and non-cavitation model and film thickness was predicted by the dynamic mesh technique. The results indicate that the effect of hydrodynamic pressure and cavitation are the important reasons to generate liquid film opening force on LST-MS; Cavitation effect can enhance hydrodynamic pressure effect of LST-MS; The thickness of liquid film could be well predicted with the method of dynamic mesh technique on Fluent and it becomes larger as the increasing of shaft speed and the decreasing of pressure.

Evaluation of a Lagrangian Soot Tracking Method for the prediction of primary soot particle size under engine-like conditions

DEFF Research Database (Denmark)

Cai Ong, Jiun; Pang, Kar Mun; Walther, Jens Honore

2018-01-01

This paper reports the implementation and evaluation of a Lagrangian soot tracking (LST) method for the modeling of soot in diesel engines. The LST model employed here has the tracking capability of a Lagrangian method and the ability to predict primary soot particle sizing. The Moss-Brookes soot...... in predicting temporal soot cloud development, mean soot diameter and primary soot size distribution is evaluated using measurements of n-heptane and n-dodecane spray combustion obtained under diesel engine-like conditions. In addition, sensitivity studies are carried out to investigate the influence of soot....... A higher rate of soot oxidation due to OH causes the soot particles to be fully oxidized downstream of the flame. In general, the LST model performs better than the Eulerian method in terms of predicting soot sizing and accessing information of individual soot particles, both of which are shortcomings...

Study on the operation mode for indigenization and standardization of AP1000 technology

International Nuclear Information System (INIS)

Gao Zhihu; Cheng Huiping

2014-01-01

This paper describes the importance and necessity of developing standardized AP1000 technology, and analyzes the problems faced and measures to be taken. The operation mode, known as the Committee of AP1000 Standardized Design and Innovation Management, was first put forward in China. And the paper also discusses how to arouse the enthusiasm of the owners, designers, manufactures, as well as construction, installation, regulation and other parties, how to exploit the advantage of whole industry to promote the localization and standardization of AP1000 technology. (authors)