WorldWideScience

Sample records for low-medium power spallation

  1. Spallator: a new option for nuclear power

    Energy Technology Data Exchange (ETDEWEB)

    Steinberg, M.; Grand, P.; Takahashi, H.; Powell, J.R.; Kouts, H.J.

    1983-06-01

    The principles of the spallator reactor are reviewed. Advances in linear accelerator technology allow the design and construction of high current (hundreds of mA) continuous wave high energy (thousands of MeV) proton machines in the near term. Spallation neutronic calculations building on existing experimental results, indicate substantial neutron yields on uranium targets. Spallator target assembly designs based on water cooled reactor technology indicate operable efficient systems. Fuel cycles are presented which supply fissile material to thermal power reactors and reduce fission product waste. Preliminary comparative analysis indicates an economically competitive system in which a single purpose self-sufficient spallator supplies fuel to a number of LWRs. The spallator assures a long-term LWR power reactor economy. International interest in advancing the technology is indicated.

  2. Material issues relating to high power spallation neutron sources

    Science.gov (United States)

    Futakawa, M.

    2015-02-01

    Innovative researches using neutrons are being performed at the Materials and Life Science Experimental Facility (MLF) at the Japan Proton Accelerator Research Complex (J-PARC), in which a mercury target system is installed for MW-class pulse spallation neutron sources. In order to produce neutrons by the spallation reaction, proton beams are injected into the mercury target. At the moment, when the intense proton beam hits the target, pressure waves are generated in mercury because of the abrupt heat deposition. The pressure waves interact with the target vessel, leading to negative pressure that may cause cavitation along the vessel wall, i.e. on the interface between liquid and solid metals. On the other hand, the structural materials are subjected to irradiation damage due to protons and neutrons, very high cycle fatigue damages and so-called "liquid metal embrittlement". That is, the structural materials must be said to be exposed to the extremely severe environments. In the paper, research and development relating to the material issues in the high power spallation neutron sources that has been performed so far at J-PARC is summarized.

  3. Spallation Neutron Source High Power RF Installation and Commissioning Progress

    CERN Document Server

    McCarthy, Michael P; Bradley, Joseph T; Fuja, Ray E; Gurd, Pamela; Hardek, Thomas; Kang, Yoon W; Rees, Daniel; Roybal, William; Young, Karen A

    2005-01-01

    The Spallation Neutron Source (SNS) linac will provide a 1 GeV proton beam for injection into the accumulator ring. In the normal conducting (NC) section of this linac, the Radio Frequency Quadupole (RFQ) and six drift tube linac (DTL) tanks are powered by seven 2.5 MW, 402.5 MHz klystrons and the four coupled cavity linac (CCL) cavities are powered by four 5.0 MW, 805 MHz klystrons. Eighty-one 550 kW, 805 MHz klystrons each drive a single cavity in the superconducting (SC) section of the linac. The high power radio frequency (HPRF) equipment was specified and procured by LANL and tested before delivery to ensure a smooth transition from installation to commissioning. Installation of RF equipment to support klystron operation in the 350-meter long klystron gallery started in June 2002. The final klystron was set in place in September 2004. Presently, all RF stations have been installed and high power testing has been completed. This paper reviews the progression of the installation and testing of the HPRF Sys...

  4. High-Power Linac for the Spallation Neutron Source

    Science.gov (United States)

    Rej, D. J.

    2002-04-01

    The Spallation Neutron Source (SNS) will be the world’s most intense source of neutrons for fundamental science and industrial applications. Design and construction of this facility, located at Oak Ridge, is a joint venture between six DOE laboratories. Construction began in 1999 and is currently ahead of the scheduled 2006 completion date. Injecting a high-power, pulsed proton beam into a mercury target produces neutrons. In this talk, we review the physics requirements, design, and status of the construction of the 1-GeV, 1.4-MW average power RF linac for SNS. The accelerator consists of a drift tube linac (DTL), a coupled-cavity linac (CCL), and a superconducting rf (SRF) linac. The phase and quadrupole settings are set to avoid structure and parametric resonances, with coherent resonances posing minimal risk for emittance growth. The DTL is 37 m long and accelerates the ions to 87 MeV. The CCL is 55 m long and accelerates the ions to 186 MeV. The rf structure design and stability for both the DTL and CCL have been validated with scale models. The SRF linac has a modular design to accelerate ions to 1000 MeV, with a straightforward upgrade to 1.3 GeV at a later date. 3D particle-in-cell simulations of beam dynamics are performed to validate performance. The accelerator utilizes 93 MW of pulsed power operating continuously at 60-Hz with an 8factor. Approximately one hundred 402.5 or 805-MHz klystrons, with outputs between 0.55 and 5 MW, are used. The klystrons are powered by a novel converter-modulator that takes advantage of recent advances in IGBT switch plate assemblies and low-loss material cores for boost transformer. Beam diagnostics include position, phase, profile, and current monitors. They are designed to enable accurate beam steering and matching, and to minimize beam loss that would lead to activation and prevent hands-on maintenance.

  5. Disposal strategy of proton irradiated mercury from high power spallation sources

    Energy Technology Data Exchange (ETDEWEB)

    Chiriki, Suresh

    2010-07-01

    Large spallation sources are intended to be constructed in Europe (EURISOL: nuclear physics research facility and ESS: European Spallation Source). These facilities would accumulate more than 20 metric tons of irradiated mercury in the target, which has to be treated as highly radioactive and chemo-toxic waste. Liquid waste cannot be tolerated in European repositories. As part of this work on safety/decommissioning of high-power spallation sources, our investigations were focused mainly to study experimentally and theoretically the solidification of liquid mercury waste (selection of an adequate solid mercury form and of an immobilization matrix, chemical engineering process studies on solidification/stabilization and on encapsulating in a matrix). Based on experimental results and supported by literature Hg-chalcogens (HgS, HgSe) will be more stable in repositories than amalgams. Our irradiation experimental studies on mercury waste revealed that mercury sulfide is a reasonable solid for disposal and shows larger stability in possible accidents with water ingress in a repository. Additionally immobilization of mercury in a cement matrix and polysiloxane matrix were tested. HgS formation from liquid target mercury by a wet process is identified as a suitable formation procedure. These investigations reveal that an almost 99.9% elementary Hg conversion can be achieved and that wet process can be reasonably handled under hot cell conditions. (orig.)

  6. Safety aspects of high power targets for European spallation sources

    Energy Technology Data Exchange (ETDEWEB)

    Moormann, Rainer; Bongardt, Klaus; Chiriki, Suresh [Forschungszentrum Juelich, D 52425 Juelich (Germany)

    2008-07-01

    An overview on the safety of options for future European high power targets is given. More detailed the safety features of a mercury target are presented. The radio-toxic inventory is comparable to that of a research reactor. The conventional mercury toxicity of the whole target cannot be neglected in relation to its radiotoxicity but. As most relevant nuclides for safety considerations Iodine-isotopes, Sr-90, Gd-148 and Hg-194 were identified. Formation of HgI{sub 2} and FeI{sub 2} during operation reduces the volatility of Iodine. For waste disposal several very long-lived nuclides have to be considered, too. Because Hg-194 cannot be separated, the whole target has to disposed. This requires mercury solidification, because liquids are not permitted in a repository. Experimental and theoretical work on mercury disposal is shortly discussed. Mercury sulphide was found to be a suitable solid compound for disposal. Its formation from target mercury by a wet process is identified as a procedure, which can be reasonably handled under hot cell conditions. (authors)

  7. Neutronic performance of the MEGAPIE spallation target under high power proton beam

    Energy Technology Data Exchange (ETDEWEB)

    Michel-Sendis, F. [CEA - Saclay, Irfu/Service de Physique Nucleaire, F91191 Gif-sur-Yvette (France); Chabod, S. [LPSC, Universite Joseph Fourier Grenoble 1, CNRS/IN2P3, 38000 Grenoble (France); Letourneau, A. [CEA - Saclay, Irfu/Service de Physique Nucleaire, F91191 Gif-sur-Yvette (France); Panebianco, S., E-mail: stefano.panebianco@cea.f [CEA - Saclay, Irfu/Service de Physique Nucleaire, F91191 Gif-sur-Yvette (France); Zanini, L. [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland)

    2010-07-01

    The MEGAPIE project, aiming at the construction and operation of a megawatt liquid lead-bismuth spallation target, constitutes the first step in demonstrating the feasibility of liquid heavy metal target technologies as spallation neutron sources. In particular, MEGAPIE is meant to assess the coupling of a high power proton beam with a window-concept heavy liquid metal target. The experiment has been set at the Paul Scherrer Institute (PSI) in Switzerland and, after a 4-month long irradiation, has provided unique data for a better understanding of the behavior of such a target under realistic irradiation conditions. A complex neutron detector has been developed to provide an on-line measurement of the neutron fluency inside the target and close to the proton beam. The detector is based on micrometric fission chambers and activation foils. These two complementary detection techniques have provided a characterization of the neutron flux inside the target for different positions along its axis. Measurements and simulation results presented in this paper aim to provide important recommendations for future accelerator driven systems (ADS) and neutron source developments.

  8. Pressure and stress waves in a spallation neutron source mercury target generated by high-power proton pulses

    CERN Document Server

    Futakawa, M; Conrad, H; Stechemesser, H

    2000-01-01

    The international ASTE collaboration has performed a first series of measurements on a spallation neutron source target at the Alternating Gradient Synchrotron (AGS) in Brookhaven. The dynamic response of a liquid mercury target hit by high-power proton pulses of about 40 ns duration has been measured by a laser Doppler technique and compared with finite elements calculations using the ABAQUS code. It is shown that the calculation can describe the experimental results for at least the time interval up to 100 mu s after the pulse injection. Furthermore, it has been observed that piezoelectric pressure transducers cannot be applied in the high gamma-radiation field of a spallation target.

  9. Study of particle transport in a high power spallation target for an accelerator driven transmutation system

    OpenAIRE

    Shetty, Nikhil Vittal

    2013-01-01

    Transmutation of highly radioactive nuclear waste can be performed using an accelerator driven system (ADS), where high energy protons impinge on a spallation target to produce neutrons. These neutrons are multiplied in a subcritical core, while simultaneously fissioning the minor actinides into short lived or stable nuclides. AGATE is a project envisaged to demonstrate the feasibility of transmutation in a gas (helium) cooled ADS using solid spallation target. Development of the spallation t...

  10. Spallation Neutron Source (SNS)

    Data.gov (United States)

    Federal Laboratory Consortium — The SNS at Oak Ridge National Laboratory is a next-generation spallation neutron source for neutron scattering that is currently the most powerful neutron source in...

  11. The EURISOL Multi Megawatt Target Station, a liquid metal target for a High Power spallation source.

    CERN Document Server

    Kharoua, C; Blumenfeld, L; Milenkovich, R; Wagner, W; Thomsen, K; Dementjevs, S; Platacis, E; Kravalis, K; Zik, A

    The European Isotope Separation On-Line Radioactive Ion Beam Facility (EURISOL) is set to be the ‘next-generation’ European Isotope Separation On-Line (ISOL) Radioactive Ion Beam (RIB) facility. It will extend and amplify current research in nuclear physics, nuclear astrophysics and fundamental interactions beyond the year 2013.In EURISOL, four target stations are foreseen, three direct targets of approximately 100 kW of beam power and one multi-MW liquid metal proton-to-neutron converter, all driven by a high-power particle accelerator. In the aforementioned multi-MW target assembly, high-intensity RIBs of neutron-rich isotopes will be obtained by inducing fission in several actinide targets surrounding a liquid metal spallation neutron source.This presentation summarises the work carried out for the Multi Megawatt target station of the EURISOL Design Study with particular attention to the coupled neutronic of the liquid converter and the overall performance of the facility, which will sustain fast neutr...

  12. Technology and science at a high-power spallation source: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    These proceedings cover many aspects of the usefulness of spallation neutrons. Nine different areas are considered: surfaces and interfaces, engineering, materials science, polymers and complex fluids, chemistry, structural biology, nuclear engineering and radiation effects, condensed matter physics and fundamental physics.

  13. Measurement and analysis of turbulent liquid metal flow in a high-power spallation neutron source-EURISOL

    CERN Document Server

    Samec, K; Blumenfeld, L; Kharoua, C; Dementjevs, S; Milenkovic, R Z

    2011-01-01

    The European Isotope Separation On-Line (EURISOL) design study completed in 2009 examined means of producing exotic nuclei for fundamental research. One of the critical components identified in the study was a high-power neutron spallation source in which a target material is impacted by a proton beam producing neutrons by a process known as spallation. Due to the high heat power deposition, liquid metal, in this case mercury, is the only viable choice as target material. Complex issues arise from the use of liquid metal. It is characterised by an unusually low Prandtl number and a higher thermal expansivity than conventional fluids. The turbulence structure in LM is thereby affected and still an object of intense research, hampered in part by measurement difficulties. The use of Computational Fluid Dynamics (CFD) allowed a satisfactory design for the neutron source to be found rapidly with little iteration. However it was feared that the development of the boundary layer and associated turbulence would not b...

  14. Pulsed spallation Neutron Sources

    Energy Technology Data Exchange (ETDEWEB)

    Carpenter, J.M. [Argonne National Lab., IL (United States)

    1994-12-31

    This paper reviews the early history of pulsed spallation neutron source development at Argonne and provides an overview of existing sources world wide. A number of proposals for machines more powerful than currently exist are under development, which are briefly described. The author reviews the status of the Intense Pulsed Neutron Source, its instrumentation, and its user program, and provides a few examples of applications in fundamental condensed matter physics, materials science and technology.

  15. Study of particle transport in a high power spallation target for an accelerator-driven transmutation system

    Energy Technology Data Exchange (ETDEWEB)

    Shetty, Nikhil Vittal

    2013-01-31

    AGATE is a project envisaged to demonstrate the feasibility of transmutation in a gas (helium) cooled accelerator-driven system using solid spallation target. Development of the spallation target module and assessing its safety aspects are studied in this work. According to the AGATE concept parameters, 600 MeV protons are delivered on to the segmented tungsten spallation target. The Monte Carlo toolkit Geant4 has been used in the simulation of particle transport. Binary cascade is used to simulate intra-nuclear cascades, along with the G4NDL neutron data library for low energy neutrons (<20 MeV).

  16. High power operation of the polyphase resonant converter modulator system for the spallation neutron source linear accelerator

    CERN Document Server

    Reass, W A; Baca, D M; Doss, J D; Gonzáles, J M; Gribble, R F; Trujillo, P G

    2003-01-01

    The spallation neutron source (SNS) is a new 1.4 MW average power beam, 1 GeV accelerator being built at Oak Ridge national laboratory. The accelerator requires 15 "long-pulse" converter-modulator stations each providing a maximum of 11 MW pulses with a 1.1 MW average power. Two variants of the converter-modulator are utilized, an 80 kV and a 140 kV design, the voltage dependant on the type of klystron load. The converter-modulator can be described as a resonant zero-voltage- switching polyphase boost inverter. As noted in Figure 1, each converter modulator derives its buss voltage from a standard 13.8 kV to 2100 Y (1.5 MVA) substation cast-core transformer. The substation also contains harmonic traps and filters to accommodate IEEE 519 and 141 regulations. Each substation is followed by an SCR preregulator to accommodate system voltage changes from no load to full load, in addition to providing a soft-start function. Energy storage and filtering is provided by special low inductance self-clearing metallized ...

  17. Spallation reactions; Reactions de spallation

    Energy Technology Data Exchange (ETDEWEB)

    Cugon, J.

    1996-12-31

    Spallation reactions dominate the interactions of hadrons with nuclei in the GeV range (from {approx} 0.1 to {approx} 10 GeV). They correspond to a sometimes important ejection of light particles leaving most of the time a residue of mass commensurate with the target mass. The main features of the experimental data are briefly reviewed. The most successful theoretical model, namely the intranuclear cascade + evaporation model, is presented. Its physical content, results and possible improvements are critically discussed. Alternative approaches are shortly reviewed. (author). 84 refs.

  18. Construction and Power Test of the Extraction Kicker Magnet for the Spallation Neutron Source Accumulator Ring

    CERN Document Server

    Pai, Chien; Hseuh Hsiao Chaun; Meng, Wuzheng; Mi, Jian-Lin; Raparia, Deepak; Sandberg, Jon; Todd, Robert J; Tsoupas, Nicholaos; Tuozzolo, Joseph; Warburton, David S; Wei, Jie; Weiss, Daniel; Yung Lee, Yong; Zhang, Wu

    2005-01-01

    Two extraction kicker magnet assemblies that contain seven individual pulsed magnet modules each will kick the proton beam vertically out of the SNS accumulator ring into the aperture of the extraction lambertson septum magnet. The proton beam then travels to the 1.4 MW SNS target assembly. The 14 kicker magnets and major components of the kicker assembly have been fabricated in BNL. The inner surfaces of the kicker magnets were coated with TiN to reduce the secondary electron yield. All 14 PFN power supplies have been built, tested and delivered to ORNL. Before final installation, a partial assembly of the kicker system with three kicker magnets was assembled to test the functions of each critical component in the system. In this paper we report the progress of the construction of the kicker components, the TiN coating of the magnets, the installation procedure of the magnets and the full power test of the kicker with the PFN power supply.

  19. Decommissioning and safety issues of liquid-mercury waste generated from high power spallation sources with particle accelerators

    CERN Document Server

    Chiriki, S; Odoj, R; Moormann, R; Hinssen, H. K; Bukaemskiy, A

    2009-01-01

    Large spallation sources are intended to be constructed in Europe (EURISOL nuclear physics facility and ESS-European Spallation Source). These facilities accumulate more than 20 metric tons of irradiated mercury in the target, which has to be treated as highly radioactive and chemo-toxic waste. Because solids are the only appropriate (immobile) form for this radiotoxic and toxic type of waste solidification is required for irradiated mercury. Our irradiation experimental studies on mercury waste revealed that mercury sulfide is a reasonable solid for disposal and shows larger stability in assumed accidents with water ingress in a repository compared to amalgams. For preparation of mercury sulfide a wet process is more suitable than a dry one. It is easier to perform under hot cell conditions and allows complete Hg-conversion. Embedding HgS in a cementitious matrix increases its stability.

  20. Determination of the ¹⁴C content in activated steel components from a neutron spallation source and a nuclear power plant.

    Science.gov (United States)

    Schumann, Dorothea; Stowasser, Tanja; Volmert, Benjamin; Günther-Leopold, Ines; Linder, Hanspeter; Wieland, Erich

    2014-06-03

    The (14)C content in activated steel components from the Swiss Nuclear Power Plant (NPP) Gösgen and the Spallation Neutron Source SINQ at the Paul Scherrer Institute is determined using a wet chemistry digestion technique and liquid scintillation counting for (14)C activity measurements. The (14)C activity of an activated fuel assembly steel nut from the NPP is further compared with theoretical predictions made on the basis of a Monte Carlo reactor model for this NPP. Knowledge of the (14)C inventory in these activated steel materials is important in conjunction with future corrosion studies on these materials aimed at identifying the (14)C containing organic compounds possibly formed in the cement-based near field of a repository for radioactive waste.

  1. Physics and technology of spallation neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, G.S.

    1998-08-01

    Next to fission and fusion, spallation is an efficient process for releasing neutrons from nuclei. Unlike the other two reactions, it is an endothermal process and can, therefore, not be used per se in energy generation. In order to sustain a spallation reaction, an energetic beam of particles, most commonly protons, must be supplied onto a heavy target. Spallation can, however, play an important role as a source of neutrons whose flux can be easily controlled via the driving beam. Up to a few GeV of energy, the neutron production is roughly proportional to the beam power. Although sophisticated Monte Carlo codes exist to compute all aspects of a spallation facility, many features can be understood on the basis of simple physics arguments. Technically a spallation facility is very demanding, not only because a reliable and economic accelerator of high power is needed to drive the reaction, but also, and in particular, because high levels of radiation and heat are generated in the target which are difficult to cope with. Radiation effects in a spallation environment are different from those commonly encountered in a reactor and are probably even more temperature dependent than the latter because of the high gas production rate. A commonly favored solution is the use of molten heavy metal targets. While radiation damage is not a problem in this case, except for the container, a number of other issues are discussed. (author)

  2. Fundamental physics possibilities at the European Spallation Source

    DEFF Research Database (Denmark)

    Klinkby, Esben Bryndt; Soldner, Torsten

    2016-01-01

    The construction of the European Spallation Source ESS is ongoing in Lund, Sweden. This new high power spallation source with its long-pulse structure opens up new possibilities for fundamental physics experiments. This paper focusses on two proposals for fundamental physics at the ESS: The ANNI...

  3. Fundamental physics possibilities at the European Spallation Source

    DEFF Research Database (Denmark)

    Klinkby, Esben Bryndt; Soldner, Torsten

    The construction of the European Spallation Source ESS is ongoing in Lund, Sweden. This new high power spallation source with its long-pulse structure opens up new possibilities for fundamental physics experiments. This paper focusses on two proposals for fundamental physics at the ESS: The ANNI...

  4. In-situ structural integrity evaluation for high-power pulsed spallation neutron source - Effects of cavitation damage on structural vibration

    Science.gov (United States)

    Wan, Tao; Naoe, Takashi; Futakawa, Masatoshi

    2016-01-01

    A double-wall structure mercury target will be installed at the high-power pulsed spallation neutron source in the Japan Proton Accelerator Research Complex (J-PARC). Cavitation damage on the inner wall is an important factor governing the lifetime of the target-vessel. To monitor the structural integrity of the target vessel, displacement velocity at a point on the outer surface of the target vessel is measured using a laser Doppler vibrometer (LDV). The measured signals can be used for evaluating the damage inside the target vessel because of cyclic loading and cavitation bubble collapse caused by pulsed-beam induced pressure waves. The wavelet differential analysis (WDA) was applied to reveal the effects of the damage on vibrational cycling. To reduce the effects of noise superimposed on the vibration signals on the WDA results, analysis of variance (ANOVA) and analysis of covariance (ANCOVA), statistical methods were applied. Results from laboratory experiments, numerical simulation results with random noise added, and target vessel field data were analyzed by the WDA and the statistical methods. The analyses demonstrated that the established in-situ diagnostic technique can be used to effectively evaluate the structural response of the target vessel.

  5. New science at the European Spallation Source

    Energy Technology Data Exchange (ETDEWEB)

    Finney, J.L. [University Coll., London (United Kingdom). Dept. of Physics and Astronomy

    1996-05-01

    The European Spallation Source is a trans-European project aimed at the ultimate construction of a next-generation pulsed spallation neutron source that will deliver 30 times the beam power of ISIS. The reference design for the proposed source has been set, and work is in progress to develop an updated scientific case for the construction of the source early in the next century. Together with improvements in instrumentation, effective flux gains of over two orders of magnitude are likely in some areas, opening up major new opportunities for the exploitation of neutron studies in fundamental, strategic, and applied science. (author)

  6. Gas production in the MEGAPIE spallation target

    Energy Technology Data Exchange (ETDEWEB)

    Thiolliere, N. [SUBATECH, EMN-IN2P3/CNRS-Universite, Nantes, F-44307 (France); Zanini, L. [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland); David, J. C. [CEA Saclay, Irfu/SPhN, 91191 Gif Sur Yvette (France); Eikenberg, J. [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland); Guertin, A. [SUBATECH, EMN-IN2P3/CNRS-Universite, Nantes, F-44307 (France); Konobeyev, A. Y. [Institut fuer Reaktorsicherheit, FZK GmbH, 76021 Karlsruhe (Germany); Lemaire, S. [CEA Bruyeres-le-Chatel, DAM Ile de France, 91297 Arpajon Cedex (France); Panebianco, S. [CEA Saclay, Irfu/SPhN, 91191 Gif Sur Yvette (France)

    2011-07-01

    The Megawatt Pilot Experiment (MEGAPIE) project was started in 2000 to design, build and operate a liquid Lead-Bismuth Eutectic (LBE) spallation neutron target at the power level of 1 MW. The target was irradiated for four months in 2006 at the Paul Scherrer Inst. in Switzerland. Gas samples were extracted in various phases of operation and analyzed by {gamma} spectroscopy leading to the determination of the main radioactive isotopes released from the LBE. Comparison with calculations performed using several validated codes (MCNPX2.5.0/CINDER'90, FLUKA/ORIHET and SNT) yields the ratio between simulated in-target isotope production rates and experimental amount released at any given time. This work underlines the weak points of spallation models for some released isotopes. Also, results provide relevant information for safety and radioprotection in an Accelerator Driven System (ADS) and more particularly for the gas management in a spallation target dedicated to neutron production facilities. (authors)

  7. Spallation modeling in tantalum

    Energy Technology Data Exchange (ETDEWEB)

    Tonks, D.L.; Hixson, R.; Zurek, A.K.; Thissell, W.

    1997-09-01

    A gas gun plate impact spallation experiment has been performed on commercial purity rolled tantalum. The shock pressure achieved was about 7 Gpa and was sufficient to induce incipient spallation. The particle velocity was measured at the free surface of the spalled plate, and the spalled sample was recovered and examined metallographically using image analysis. The quantitative image analysis results are being used to develop a damage model. The model is micromechanically based and involves novel void growth and coalescence processes. The 1D characteristics code CHARADE has been used in a preliminary simulation of the VISAR free surface particle velocity record. Implications for ductile damage modeling will be discussed.

  8. A novel vacuum spectrometer for total reflection x-ray fluorescence analysis with two exchangeable low power x-ray sources for the analysis of low, medium, and high Z elements in sequence

    Energy Technology Data Exchange (ETDEWEB)

    Wobrauschek, P., E-mail: wobi@ati.ac.at; Prost, J.; Ingerle, D.; Kregsamer, P.; Streli, C. [Atominstitut, TU Wien, Stadionallee 2, 1020 Vienna (Austria); Misra, N. L. [Fuel Chemistry Division, Bhabha Atomic Research Centre (BARC), Mumbai 400085 (India)

    2015-08-15

    The extension of the detectable elemental range with Total Reflection X-ray Fluorescence (TXRF) analysis is a challenging task. In this paper, it is demonstrated how a TXRF spectrometer is modified to analyze elements from carbon to uranium. Based on the existing design of a vacuum TXRF spectrometer with a 12 specimen sample changer, the following components were renewed: the silicon drift detector with 20 mm{sup 2} active area and having a special ultra-thin polymer window allowing the detection of elements from carbon upwards. Two exchangeable X-ray sources guarantee the efficient excitation of both low and high Z elements. These X-ray sources were two light-weighted easily mountable 35 W air-cooled low-power tubes with Cr and Rh anodes, respectively. The air cooled tubes and the Peltier-cooled detector allowed to construct a transportable tabletop spectrometer with compact dimensions, as neither liquid nitrogen cooling for the detector nor a water cooling circuit and a bulky high voltage generator for the X-ray tubes are required. Due to the excellent background conditions as a result of the TXRF geometry, detection limits of 150 ng for C, 12 ng for F, and 3.3 ng for Na have been obtained using Cr excitation in vacuum. For Rh excitation, the detection limits of 90 pg could be achieved for Sr. Taking 10 to 20 μl of sample volume, extrapolated detection limits in the ng/g (ppb) range are resulting in terms of concentration.

  9. A novel vacuum spectrometer for total reflection x-ray fluorescence analysis with two exchangeable low power x-ray sources for the analysis of low, medium, and high Z elements in sequence.

    Science.gov (United States)

    Wobrauschek, P; Prost, J; Ingerle, D; Kregsamer, P; Misra, N L; Streli, C

    2015-08-01

    The extension of the detectable elemental range with Total Reflection X-ray Fluorescence (TXRF) analysis is a challenging task. In this paper, it is demonstrated how a TXRF spectrometer is modified to analyze elements from carbon to uranium. Based on the existing design of a vacuum TXRF spectrometer with a 12 specimen sample changer, the following components were renewed: the silicon drift detector with 20 mm(2) active area and having a special ultra-thin polymer window allowing the detection of elements from carbon upwards. Two exchangeable X-ray sources guarantee the efficient excitation of both low and high Z elements. These X-ray sources were two light-weighted easily mountable 35 W air-cooled low-power tubes with Cr and Rh anodes, respectively. The air cooled tubes and the Peltier-cooled detector allowed to construct a transportable tabletop spectrometer with compact dimensions, as neither liquid nitrogen cooling for the detector nor a water cooling circuit and a bulky high voltage generator for the X-ray tubes are required. Due to the excellent background conditions as a result of the TXRF geometry, detection limits of 150 ng for C, 12 ng for F, and 3.3 ng for Na have been obtained using Cr excitation in vacuum. For Rh excitation, the detection limits of 90 pg could be achieved for Sr. Taking 10 to 20 μl of sample volume, extrapolated detection limits in the ng/g (ppb) range are resulting in terms of concentration.

  10. Linac-driven spallation-neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Jason, A.J.

    1995-05-01

    Strong interest has arisen in accelerator-driven spallation-neutron sources that surpass existing facilities (such as ISIS at Rutherford or LANSCE at Los Alamos) by more than an order of magnitude in beam power delivered to the spallation target. The approach chosen by Los Alamos (as well as the European Spallation Source) provides the full beam energy by acceleration in a linac as opposed to primary acceleration in a synchrotron or other circular device. Two modes of neutron production are visualized for the source. A short-pulse mode produces 1 MW of beam power (at 60 pps) in pulses, of length less than 1 ms, by compression of the linac macropulse through multi-turn injection in an accumulator ring. A long-pulse mode produces a similar beam power with 1-ms-long pulses directly applied to a target. This latter mode rivals the performance of existing reactor facilities to very low neutron energies. Combination with the short-pulse mode addresses virtually all applications.

  11. Thermal features of spallation window targets

    Energy Technology Data Exchange (ETDEWEB)

    Abanades, Alberto; Sordo, Fernando; Lafuente, Antonio [E.T.S. Industriales, Madrid Polytechnic University, UPM, J. Gutierrez Abascal, 2, 28006 Madrid (Spain); Martinez-Val, Jose M. [E.T.S. Industriales, Madrid Polytechnic University, UPM, J. Gutierrez Abascal, 2, 28006 Madrid (Spain)], E-mail: mval@etsii.upm.es

    2008-07-15

    The spallation process is a cascade of nuclear reactions induced by medium-energy hadrons, notably protons, which impinge in a suitable material as accelerated particles. A main outcome of that cascade is a shower of medium and high-energy neutrons, which can be used for irradiation purposes or to feed a subcritical reactor. The neutron production is accompanied by the generation of a broad set of radioactive products, which presents specific problems of radiological protection and decay heat removal. The nominal heat load is another point of concern, because of the very high power densities produced in the proton beam energy deposition in the interaction region. All these phenomena are taken into account in this paper in order to set up an integral and coherent task flowchart in order to guide the design of spallation sources.

  12. On the Role of Laser Pulses on Spallation of Granite

    Science.gov (United States)

    Ndeda, Rehema; Sebusang, Sebusang E. M.; Marumo, Rapelang; Ogur, Erich O.

    2017-06-01

    Laser spallation is one of the thermal methods under study as an alternative to mechanical drilling mainly due to high power capabilities and non-contact nature. Spallation has been attributed to stress generated on the rock due to large temperature gradient and thermal expansion of the rock. It is necessary to determine the effect of pulsing of the laser as well as convective cooling on spallation, in a bid to increase the efficiency of laser spallation. In this paper, analysis of thermal stresses during pulsed laser spallation of granite is carried out. The effect of convective cooling at the end of the heating period on stress and crack propagation is also examined. A two dimensional finite element model is developed. It is observed that on cooling, tensile stresses generated during heating are inverted to compressive stresses, increasing the rate of spallation. Results also indicate that residual stresses on the rock due to pulsing are much higher. Finally, increased rate of crack propagation is observed when the rock is subjected to sudden cooling.

  13. Further considerations of spallation effects

    Science.gov (United States)

    Dyer, C.

    1973-01-01

    Trapped photon and cosmic ray effects on spallation in the UK-5 (hard X ray telescope) central crystal were measured. Both low dose and high dose effects were considered. Decay results are presented in tables.

  14. Fission, spallation or fusion-based neutron sources

    Indian Academy of Sciences (India)

    Kurt N Clausen

    2008-10-01

    In this paper the most promising technology for high power neutron sources is briefly discussed. The conclusion is that the route to high power neutron sources in the foreseeable future is spallation – short or long pulse or even CW – all of these sources will have areas in which they excel.

  15. Design Optimization and the path towards a 2 MW Spallation Neutron Source

    Energy Technology Data Exchange (ETDEWEB)

    M. Blaskiewicz; N. Catalan-Lasheras; D. Davino; A. Fedotov; Y. Lee; N. Malitsky; Y. Papaphilippou; D. Raparia; A. Shishlo; N. Tsoupas; J. Wei; W. Weng; S. Zhang; J. Billen; S. Kurennoy; S. Nath; J. Stovall; H. Takeda; L. Young; R. Keller; J. Staples; A. Aleksandrov; Y. Cho; P. Chu; S. Cousineau; V. Danilov; M. Doleans; J. Galambos; J. Holmes; N. Holtkamp; D. Jeon; S. Kim; R. Kustom; E. Tanke; W. Wan; R. Sundelin

    2001-08-01

    The Spallation Neutron Source (SNS) is designed to ultimately reach an average proton beam power of 2 MW for pulsed neutron production. The SNS physics groups analyze the machine performance within the hardware constraints, optimize the accelerator design, and establish the best path towards a 2 MW and higher spallation neutron source.

  16. Research activities on structure materials of spallation neutron source at SINQ

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, G.S.; Dai, Y. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-09-01

    With the growing interests on powerful spallation neutron sources, especially with liquid metal targets, and accelerator driven energy systems, spallation materials science and technology have been received wide attention. At SINQ, material research activities are focused on: a) liquid metal corrosion; b) radiation damage; and c) interaction of corrosion and radiation damage. (author) 1 fig., refs.

  17. GRAIN-SCALE FAILURE IN THERMAL SPALLATION DRILLING

    Energy Technology Data Exchange (ETDEWEB)

    Walsh, S C; Lomov, I; Roberts, J J

    2012-01-19

    Geothermal power promises clean, renewable, reliable and potentially widely-available energy, but is limited by high initial capital costs. New drilling technologies are required to make geothermal power financially competitive with other energy sources. One potential solution is offered by Thermal Spallation Drilling (TSD) - a novel drilling technique in which small particles (spalls) are released from the rock surface by rapid heating. While TSD has the potential to improve drilling rates of brittle granitic rocks, the coupled thermomechanical processes involved in TSD are poorly described, making system control and optimization difficult for this drilling technology. In this paper, we discuss results from a new modeling effort investigating thermal spallation drilling. In particular, we describe an explicit model that simulates the grain-scale mechanics of thermal spallation and use this model to examine existing theories concerning spalling mechanisms. We will report how borehole conditions influence spall production, and discuss implications for macro-scale models of drilling systems.

  18. Materials for spallation neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Sommer, W.F.; Daemen, L.L. [comps.

    1996-03-01

    The Workshop on Materials for Spallation Neutron Sources at the Los Alamos Neutron Science Center, February 6 to 10, 1995, gathered scientists from Department of Energy national laboratories, other federal institutions, universities, and industry to discuss areas in which work is needed, successful designs and use of materials, and opportunities for further studies. During the first day of the workshop, speakers presented overviews of current spallation neutron sources. During the next 3 days, seven panels allowed speakers to present information on a variety of topics ranging from experimental and theoretical considerations on radiation damage to materials safety issues. An attempt was made to identify specific problems that require attention within the context of spallation neutron sources. This proceedings is a collection of summaries from the overview sessions and the panel presentations.

  19. Neutron scattering instrumentation for biology at spallation neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Pynn, R. [Los Alamos National Laboratory, NM (United States)

    1994-12-31

    Conventional wisdom holds that since biological entities are large, they must be studied with cold neutrons, a domain in which reactor sources of neutrons are often supposed to be pre-eminent. In fact, the current generation of pulsed spallation neutron sources, such as LANSCE at Los Alamos and ISIS in the United Kingdom, has demonstrated a capability for small angle scattering (SANS) - a typical cold- neutron application - that was not anticipated five years ago. Although no one has yet built a Laue diffractometer at a pulsed spallation source, calculations show that such an instrument would provide an exceptional capability for protein crystallography at one of the existing high-power spoliation sources. Even more exciting is the prospect of installing such spectrometers either at a next-generation, short-pulse spallation source or at a long-pulse spallation source. A recent Los Alamos study has shown that a one-megawatt, short-pulse source, which is an order of magnitude more powerful than LANSCE, could be built with today`s technology. In Europe, a preconceptual design study for a five-megawatt source is under way. Although such short-pulse sources are likely to be the wave of the future, they may not be necessary for some applications - such as Laue diffraction - which can be performed very well at a long-pulse spoliation source. Recently, it has been argued by Mezei that a facility that combines a short-pulse spallation source similar to LANSCE, with a one-megawatt, long-pulse spallation source would provide a cost-effective solution to the global shortage of neutrons for research. The basis for this assertion as well as the performance of some existing neutron spectrometers at short-pulse sources will be examined in this presentation.

  20. Status of spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Oyama, Yukio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-03-01

    Existing and planned facilities using proton accelerator driven spallation neutron source are reviewed. These include new project of neutron science proposed from Japan Atomic Energy Research Institute. The present status of facility requirement and accelerator technology leads us to new era of neutron science such as neutron scattering research and nuclear transmutation study using very intense neutron source. (author)

  1. The European scene regarding spallation neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, G.S. [Paul Scherrer Institut, Villigen (Austria)

    1996-06-01

    In Europe, a short pulse spallation neutron source, ISIS, has been operating for over 10 years, working its way up to a beam power level of 200 kW. A continuous source, SINQ, designed for a beam power of up to 1 MW, is scheduled to start operating at the end of 1996, and a detailed feasibility study has been completed for a 410 kW short pulse source, AUSTRON. Each of these sources seems to have settled for a target concept which is at or near the limits of its feasibility: The ISIS depleted uranium plate targets, heavy water cooled and Zircaloy clad, have so far not shown satisfactory service time and operation is likely to continue with a Ta-plate target, which, in the past has been used successfully for the equivalent of one full-beam-year before it was taken out of service due to degrading thermal properties. SINQ will initially use a rod target, made of Zircaloy only, but plans exist to move on to clad lead rods as quickly as possible. Apart from the not yet explored effect of hydrogen and helium production, there are also concerns about the generation of 7-Be in the cooling water from the spallation of oxygen, which might result in undesirably high radioactivity in the cooling plant room. A Liquid metal target, also under investigation for SINQ, would not only reduce this problem to a level of about 10 %, but would also minimize the risk of radiolytic corrosion in the beam interaction zone. Base on similar arguments, AUSTRON has been designed for edge cooled targets, but thermal and stress analyses show, that this concept is not feasible at higher power levels.

  2. Spallation radiation effects in materials

    Energy Technology Data Exchange (ETDEWEB)

    Mansur, L.K.; Farrell, K.; Wechsler, M.S. [Oak Ridge National Lab., TN (United States)

    1996-06-01

    Spallation refers to the process whereby particles (chiefly neutrons) are ejected from nuclei upon bombardment by high-energy protons. Spallation neutron sources (SNS`s) use these neutrons for neutron scattering and diffraction research, and SNS`s are proposed as the basis for systems for tritium production and transmutation of nuclear waste. Materials in SNS`s are exposed to the incident proton beam (energies typically about 1000 MeV) and to the spallation neutrons (spectrum of energies extending up to about 1000 MeV). By contrast the fission neutrons in nuclear reactors have an average energy of only about 2 MeV, and the neutrons in fusion reactors would have energies below about 14 MeV. Furthermore, the protons and neutrons in SNS`s for scattering and diffraction research are pulsed at frequencies of about 10 to 60 Hz, from which significant changes in the kinetics of point and extended defects may be expected. In addition, much higher transmutation rates occur in SNS-irradiated materials, On the whole, then, significant differences in microstructural development and macroscopic properties may result upon exposure in SNS systems, as compared with fission and fusion irradiations. In a more general sense, subjecting materials to new radiation environments has almost routinely led to new discoveries. To the extent that data are avaiable, however, the spallation environment appears to increase the degree of damage without introducing totally new effects. The first part of this presentation is an overview of radiation effects in materials, outlining essential concepts and property changes and their physical bases. This background is followed by a description of SNS irradiation environments and the effects on materials of exposure to these environments. A special discussion is given of the selection of target (e.g., liquid mercury), container (e.g., austenitic stainless steel or ferritic/martensitic steel), and structural materials in SNS systems.

  3. 30 CFR 75.511 - Low-, medium-, or high-voltage distribution circuits and equipment; repair.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Low-, medium-, or high-voltage distribution... Electrical Equipment-General § 75.511 Low-, medium-, or high-voltage distribution circuits and equipment; repair. No electrical work shall be performed on low-, medium-, or high-voltage distribution circuits or...

  4. Status of the AUSTRON spallation project

    Science.gov (United States)

    Rauch, H.; Regler, M.; Weber, H.

    2000-03-01

    The characteristic parameters of the present version of the planned AUSTRON neutron spallation source are: (a) 10 Hz repetition rate at the target, (b) 500 kW average beam power, (c) 1.6 GeV proton energy and (d) strongly dedicated to cold neutron research. The machine can be built based on existing techniques and would provide a performance gain between 3 and 10 compared to existing installations. Progress has been made in the planning of the instrumentation where an improved standard instrumentation and several new systems have been designed and evaluated by an international group of neutron scientists. A clean room area with vibration, temperature and humidity control provides new possibilities for neutron optics, neutron reflectometry and nuclear orientation experiments. A proposed magnetic focusing line with an active energy transfer system indicates the capability to achieve a further intensity gain by a factor of 10. The status of the ongoing internationalization process will be reported as well.

  5. Radiochemical aspects of liquid mercury spallation targets

    CERN Document Server

    Neuhausen, Joerg; Eichler, Bernd; Eller, Martin; Horn, Susanne; Schumann, Dorothea; Stora, Thierry

    2012-01-01

    Liquid metal spallation targets using mercury as target material are used in state-of-the-art high power pulsed neutron sources that have been constructed in the USA and Japan within the last decade. Similar target concepts were also proposed for next generation ISOL, beta-beam and neutrino facilities. A large amount of radioactivity will be induced in the liquid metal during operation caused by the interaction of the target material with the intense proton beam. This radioactivity - carried by a wide range of radioisotopes of all the elements of the periodic table from hydrogen up to thallium - must be considered for the assessment of safe operation and maintenance procedures as well as for a final disposal of the used target material and components. This report presents an overview on chemical investigations performed in our laboratory that deal with the behavior of radionuclides in proton irradiated mercury samples. The solubility of elements in mercury was calculated using thermodynamical data obtained by...

  6. Mercury purification in the megawatt liquid metal spallation target of EURISOL-DS

    CERN Document Server

    Neuhausen, Joerg; Eller, Martin; Schumann, Dorothea; Eichler, Bernd; Horn, Susanne

    High power spallation targets are going to be used extensively in future research and technical facilities such as spallation neutron sources, neutrino factories, radioactive beam facilities or accelerator driven systems for the transmutation of long-lived nuclear waste. Within EURISOL-DS, a 4 MW liquid metal spallation target is designed to provide neutrons for a fission target, where neutron rich radionuclides will be produced. For the spallation target, mercury is planned to be used as target material. A large amount of radionuclides ranging from atomic number Z=1 to 81 will be produced in the liquid metal during long term irradiation. It is planned to remove those radionuclides by chemical or physicochemical methods to reduce its radioactivity. For the development of a purification procedure, knowledge about the chemical state of the different elements present in the mixture is required. We present a general concept of applicable separation techniques in a target system and show some results of experiment...

  7. The Spallation Neutron Source accelerator system design

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, S., E-mail: stuarth@fnal.gov [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States); Abraham, W. [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Aleksandrov, A. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States); Allen, C. [Techsource, Inc., 1475 Central Avenue, Suite 250, Los Alamos, NM 87544-3291 (United States); Alonso, J. [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Anderson, D. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States); Arenius, D. [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Arthur, T. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States); Assadi, S. [Techsource, Inc., 1475 Central Avenue, Suite 250, Los Alamos, NM 87544-3291 (United States); Ayers, J.; Bach, P. [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Badea, V. [Brookhaven National Laboratory, P.O. Box 5000, Upton, NY 11973-5000 (United States); Battle, R. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States); Beebe-Wang, J. [Brookhaven National Laboratory, P.O. Box 5000, Upton, NY 11973-5000 (United States); Bergmann, B.; Bernardin, J.; Bhatia, T.; Billen, J.; Birke, T.; Bjorklund, E. [Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States); and others

    2014-11-01

    The Spallation Neutron Source (SNS) was designed and constructed by a collaboration of six U.S. Department of Energy national laboratories. The SNS accelerator system consists of a 1 GeV linear accelerator and an accumulator ring providing 1.4 MW of proton beam power in microsecond-long beam pulses to a liquid mercury target for neutron production. The accelerator complex consists of a front-end negative hydrogen-ion injector system, an 87 MeV drift tube linear accelerator, a 186 MeV side-coupled linear accelerator, a 1 GeV superconducting linear accelerator, a 248-m circumference accumulator ring and associated beam transport lines. The accelerator complex is supported by ∼100 high-power RF power systems, a 2 K cryogenic plant, ∼400 DC and pulsed power supply systems, ∼400 beam diagnostic devices and a distributed control system handling ∼100,000 I/O signals. The beam dynamics design of the SNS accelerator is presented, as is the engineering design of the major accelerator subsystems.

  8. The Spallation Neutron Source accelerator system design

    Science.gov (United States)

    Henderson, S.; Abraham, W.; Aleksandrov, A.; Allen, C.; Alonso, J.; Anderson, D.; Arenius, D.; Arthur, T.; Assadi, S.; Ayers, J.; Bach, P.; Badea, V.; Battle, R.; Beebe-Wang, J.; Bergmann, B.; Bernardin, J.; Bhatia, T.; Billen, J.; Birke, T.; Bjorklund, E.; Blaskiewicz, M.; Blind, B.; Blokland, W.; Bookwalter, V.; Borovina, D.; Bowling, S.; Bradley, J.; Brantley, C.; Brennan, J.; Brodowski, J.; Brown, S.; Brown, R.; Bruce, D.; Bultman, N.; Cameron, P.; Campisi, I.; Casagrande, F.; Catalan-Lasheras, N.; Champion, M.; Champion, M.; Chen, Z.; Cheng, D.; Cho, Y.; Christensen, K.; Chu, C.; Cleaves, J.; Connolly, R.; Cote, T.; Cousineau, S.; Crandall, K.; Creel, J.; Crofford, M.; Cull, P.; Cutler, R.; Dabney, R.; Dalesio, L.; Daly, E.; Damm, R.; Danilov, V.; Davino, D.; Davis, K.; Dawson, C.; Day, L.; Deibele, C.; Delayen, J.; DeLong, J.; Demello, A.; DeVan, W.; Digennaro, R.; Dixon, K.; Dodson, G.; Doleans, M.; Doolittle, L.; Doss, J.; Drury, M.; Elliot, T.; Ellis, S.; Error, J.; Fazekas, J.; Fedotov, A.; Feng, P.; Fischer, J.; Fox, W.; Fuja, R.; Funk, W.; Galambos, J.; Ganni, V.; Garnett, R.; Geng, X.; Gentzlinger, R.; Giannella, M.; Gibson, P.; Gillis, R.; Gioia, J.; Gordon, J.; Gough, R.; Greer, J.; Gregory, W.; Gribble, R.; Grice, W.; Gurd, D.; Gurd, P.; Guthrie, A.; Hahn, H.; Hardek, T.; Hardekopf, R.; Harrison, J.; Hatfield, D.; He, P.; Hechler, M.; Heistermann, F.; Helus, S.; Hiatt, T.; Hicks, S.; Hill, J.; Hill, J.; Hoff, L.; Hoff, M.; Hogan, J.; Holding, M.; Holik, P.; Holmes, J.; Holtkamp, N.; Hovater, C.; Howell, M.; Hseuh, H.; Huhn, A.; Hunter, T.; Ilg, T.; Jackson, J.; Jain, A.; Jason, A.; Jeon, D.; Johnson, G.; Jones, A.; Joseph, S.; Justice, A.; Kang, Y.; Kasemir, K.; Keller, R.; Kersevan, R.; Kerstiens, D.; Kesselman, M.; Kim, S.; Kneisel, P.; Kravchuk, L.; Kuneli, T.; Kurennoy, S.; Kustom, R.; Kwon, S.; Ladd, P.; Lambiase, R.; Lee, Y. Y.; Leitner, M.; Leung, K.-N.; Lewis, S.; Liaw, C.; Lionberger, C.; Lo, C. C.; Long, C.; Ludewig, H.; Ludvig, J.; Luft, P.; Lynch, M.; Ma, H.; MacGill, R.; Macha, K.; Madre, B.; Mahler, G.; Mahoney, K.; Maines, J.; Mammosser, J.; Mann, T.; Marneris, I.; Marroquin, P.; Martineau, R.; Matsumoto, K.; McCarthy, M.; McChesney, C.; McGahern, W.; McGehee, P.; Meng, W.; Merz, B.; Meyer, R.; Meyer, R.; Miller, B.; Mitchell, R.; Mize, J.; Monroy, M.; Munro, J.; Murdoch, G.; Musson, J.; Nath, S.; Nelson, R.; Nelson, R.; O`Hara, J.; Olsen, D.; Oren, W.; Oshatz, D.; Owens, T.; Pai, C.; Papaphilippou, I.; Patterson, N.; Patterson, J.; Pearson, C.; Pelaia, T.; Pieck, M.; Piller, C.; Plawski, T.; Plum, M.; Pogge, J.; Power, J.; Powers, T.; Preble, J.; Prokop, M.; Pruyn, J.; Purcell, D.; Rank, J.; Raparia, D.; Ratti, A.; Reass, W.; Reece, K.; Rees, D.; Regan, A.; Regis, M.; Reijonen, J.; Rej, D.; Richards, D.; Richied, D.; Rode, C.; Rodriguez, W.; Rodriguez, M.; Rohlev, A.; Rose, C.; Roseberry, T.; Rowton, L.; Roybal, W.; Rust, K.; Salazer, G.; Sandberg, J.; Saunders, J.; Schenkel, T.; Schneider, W.; Schrage, D.; Schubert, J.; Severino, F.; Shafer, R.; Shea, T.; Shishlo, A.; Shoaee, H.; Sibley, C.; Sims, J.; Smee, S.; Smith, J.; Smith, K.; Spitz, R.; Staples, J.; Stein, P.; Stettler, M.; Stirbet, M.; Stockli, M.; Stone, W.; Stout, D.; Stovall, J.; Strelo, W.; Strong, H.; Sundelin, R.; Syversrud, D.; Szajbler, M.; Takeda, H.; Tallerico, P.; Tang, J.; Tanke, E.; Tepikian, S.; Thomae, R.; Thompson, D.; Thomson, D.; Thuot, M.; Treml, C.; Tsoupas, N.; Tuozzolo, J.; Tuzel, W.; Vassioutchenko, A.; Virostek, S.; Wallig, J.; Wanderer, P.; Wang, Y.; Wang, J. G.; Wangler, T.; Warren, D.; Wei, J.; Weiss, D.; Welton, R.; Weng, J.; Weng, W.-T.; Wezensky, M.; White, M.; Whitlatch, T.; Williams, D.; Williams, E.; Wilson, K.; Wiseman, M.; Wood, R.; Wright, P.; Wu, A.; Ybarrolaza, N.; Young, K.; Young, L.; Yourd, R.; Zachoszcz, A.; Zaltsman, A.; Zhang, S.; Zhang, W.; Zhang, Y.; Zhukov, A.

    2014-11-01

    The Spallation Neutron Source (SNS) was designed and constructed by a collaboration of six U.S. Department of Energy national laboratories. The SNS accelerator system consists of a 1 GeV linear accelerator and an accumulator ring providing 1.4 MW of proton beam power in microsecond-long beam pulses to a liquid mercury target for neutron production. The accelerator complex consists of a front-end negative hydrogen-ion injector system, an 87 MeV drift tube linear accelerator, a 186 MeV side-coupled linear accelerator, a 1 GeV superconducting linear accelerator, a 248-m circumference accumulator ring and associated beam transport lines. The accelerator complex is supported by ~100 high-power RF power systems, a 2 K cryogenic plant, ~400 DC and pulsed power supply systems, ~400 beam diagnostic devices and a distributed control system handling ~100,000 I/O signals. The beam dynamics design of the SNS accelerator is presented, as is the engineering design of the major accelerator subsystems.

  9. Synchrotron based spallation neutron source concepts

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Y.

    1998-07-01

    During the past 20 years, rapid-cycling synchrotrons (RCS) have been used very productively to generate short-pulse thermal neutron beams for neutron scattering research by materials science communities in Japan (KENS), the UK (ISIS) and the US (IPNS). The most powerful source in existence, ISIS in the UK, delivers a 160-kW proton beam to a neutron-generating target. Several recently proposed facilities require proton beams in the MW range to produce intense short-pulse neutron beams. In some proposals, a linear accelerator provides the beam power and an accumulator ring compresses the pulse length to the required {approx} 1 {micro}s. In others, RCS technology provides the bulk of the beam power and compresses the pulse length. Some synchrotron-based proposals achieve the desired beam power by combining two or more synchrotrons of the same energy, and others propose a combination of lower and higher energy synchrotrons. This paper presents the rationale for using RCS technology, and a discussion of the advantages and disadvantages of synchrotron-based spallation sources.

  10. An overview of an accelerator-based neutron spallation source

    Energy Technology Data Exchange (ETDEWEB)

    Lessner, E.S.

    1996-06-01

    An overview of the feasibility study of a 1-MW pulsed spallation source is presented. The machine delivers 1 MW of proton beam power to spallation targets where slow neutrons are produced. The slow neutrons can be used for isotope production, materials irradiation, and neutron scattering research. The neutron source facility is based on a rapid cycling synchrotron (RCS) and consists of a 400-MeV linac, a 30-Hz RCS that accelerates the 400-MeV beam to 2 GeV, and two neutron-generating target stations. The RCS accelerates an average proton beam current of 0.5 mA, corresponding to 1.04 x 10{sup 14} protons per pulse. This intensity is about two times higher than that of existing machines. A key feature of this accelerator system design is that beam losses are minimized from injection to extraction, reducing activation to levels consistent with hands-on maintenance.

  11. Neutronic studies of the coupled moderators for spallation neutron sources

    Institute of Scientific and Technical Information of China (English)

    Yin Wen; Liang Jiu-Qing

    2005-01-01

    We investigate the neutronic performance of coupled moderators to be implemented in spallation neutron sources by Monte-Carlo simulation and give the slow neutron spectra for the cold and thermal moderators. CH4 moderator can provide slow neutrons with highly desirable characteristics and will be used in low-power spallation neutron soureces. The slow neutron intensity extracted from different angles has been calculated. The capability of moderation of liquid H2 is lower than H2O and liquid CH4 due to lower atomic number density of hydrogen but we can compensate for this disadvantage by using a premoderator. The H2O premoderator of 2cm thickness can reduce the heat deposition in the cold moderator by about 33% without spoiling the neutron pulse.

  12. Dose measurements around spallation neutron sources.

    Science.gov (United States)

    Fragopoulou, M; Stoulos, S; Manolopoulou, M; Krivopustov, M; Zamani, M

    2008-01-01

    Neutron dose measurements and calculations around spallation sources appear to be of great importance in shielding research. Two spallation sources were irradiated by high-energy proton beams delivered by the Nuclotron accelerator (JINR), Dubna. Neutrons produced by the spallation sources were measured by using solid-state nuclear track detectors. In addition, neutron dose was calculated after polyethylene and concrete, using a phenomenological model based on empirical relations applied in high-energy physics. The study provides an analytical and experimental neutron benchmark analysis using the transmission factor and a comparison between the experimental results and calculations.

  13. Target station shielding issues at the spallation neutron source.

    Science.gov (United States)

    Ferguson, P D; Gallmeier, F X; Iverson, E B; Popova, I I

    2005-01-01

    Recent spallation neutron source shielding activities in support of the neutron beam shutters and the hot cell walls are presented. Existing neutron beam shutters can be replaced with concrete at low power or with concrete and steel at approximately 500 kW of beam power. Potential voids in the hot cell walls are analysed to determine the impact on dose rates as a function of void size. A change in the type of shielding work is noted as the project moved from the early design stages as a 'green field' site to the current stage as a construction project nearing completion, where issues to be addressed are approaching retrofit-type analyses.

  14. Cooperative effort between Consorcio European Spallation Source--Bilbao and Oak Ridge National Laboratory spallation neutron source for manufacturing and testing of the JEMA-designed modulator system

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, David E [ORNL

    2017-01-02

    The JEMA modulator was originally developed for the European Spallation Source (ESS) when Spain was under consideration as a location for the ESS facility. Discussions ensued and the Spallation Neutron Source Research Accelerator Division agreed to form a collaboration with ESS-Bilbao (ESS-B) consortium to provide services for specifying the requirements for a version of the modulator capable of operating twelve 550 kW klystrons, monitoring the technical progress on the contract with JEMA, installing and commissioning the modulator at SNS, and performing a 30 day full power test. This work was recently completed, and this report discusses those activities with primary emphasis on the installation and testing activities.

  15. Cryogenic System for the Spallation Neutron Source

    Science.gov (United States)

    Arenius, D.; Chronis, W.; Creel, J.; Dixon, K.; Ganni, V.; Knudsen, P.

    2004-06-01

    The Spallation Neutron Source (SNS) is a neutron-scattering facility being built at Oak Ridge, TN for the US Department of Energy. The SNS accelerator linac consists of superconducting radio-frequency (SRF) cavities in cryostats (cryomodules). The linac cryomodules are cooled to 2.1 K by a 2300 watt cryogenic refrigeration system. As an SNS partner laboratory, Jefferson Lab is responsible for the installed integrated cryogenic system design for the SNS linac accelerator consisting of major subsystem equipment engineered and procured from industry. Jefferson Lab's work included developing the major vendor subsystem equipment procurement specifications, equipment procurement, and the integrated system engineering support of the field installation and commissioning. The major cryogenic system components include liquid nitrogen storage, gaseous helium storage, cryogen distribution transfer line system, 2.1-K cold box consisting of four stages of cold compressors, 4.5-K cold box, warm helium compressors with its associated oil removal, gas management, helium purification, gas impurity monitoring systems, and the supportive utilities of electrical power, cooling water and instrument air. The system overview, project organization, the important aspects, and the capabilities of the cryogenic system are described.

  16. Synchrotron-driven spallation sources

    CERN Document Server

    Bryant, P J

    1996-01-01

    The use of synchrotrons for pulsed neutron spallation sources is an example of scientific and technological spin-off from the accelerator development for particle physics. Accelerator-driven sources provide an alternative to the continuous-flux, nuclear reactors that currently furnish the majority of neutrons for research and development. Although the present demand for neutrons can be adequately met by the existing reactors, this situation is unlikely to continue due to the increasing severity of safety regulations and the declared policies of many countries to close down their reactors within the next decade or so. Since the demand for neutrons as a research tool is, in any case,expected to grow, there has been a corresponding interest in sources that are synchrotron-driven or linac-driven with a pulse compression ring and currently several design studies are being made. These accelerator-driven sources also have the advantage of a time structure with a high peak neutron flux. The basic requirement is for a...

  17. SPALLATION NEUTRON SOURCE RING-DESIGN AND CONSTRUCTION SUMMARY.

    Energy Technology Data Exchange (ETDEWEB)

    WEI,J.

    2005-05-16

    After six years, the delivery of components for the Spallation Neutron Source (SNS) accumulator ring (AR) and the transport lines was completed in Spring 2005. Designed to deliver 1.5 MW beam power (1.5 x 10{sup 14} protons of 1 GeV kinetic energy at a repetition rate of 60 Hz), stringent measures were implemented in the fabrication, test, and assembly to ensure the quality of the accelerator systems. This paper summarizes the design, R&D, and construction of the ring and transport systems.

  18. HPC simulations of grain-scale spallation to improve thermal spallation drilling

    Science.gov (United States)

    Walsh, S. D.; Lomov, I.; Wideman, T. W.; Potter, J.

    2012-12-01

    Thermal spallation drilling and related hard-rock hole opening techniques are transformative technologies with the potential to dramatically reduce the costs associated with EGS well drilling and improve the productivity of new and existing wells. In contrast to conventional drilling methods that employ mechanical means to penetrate rock, thermal spallation methods fragment rock into small pieces ("spalls") without contact via the rapid transmission of heat to the rock surface. State-of-the-art constitutive models of thermal spallation employ Weibull statistical failure theory to represent the relationship between rock heterogeneity and its propensity to produce spalls when heat is applied to the rock surface. These models have been successfully used to predict such factors as penetration rate, spall-size distribution and borehole radius from drilling jet velocity and applied heat flux. A properly calibrated Weibull model would permit design optimization of thermal spallation drilling under geothermal field conditions. However, although useful for predicting system response in a given context, Weibull models are by their nature empirically derived. In the past, the parameters used in these models were carefully determined from laboratory tests, and thus model applicability was limited by experimental scope. This becomes problematic, for example, if simulating spall production at depths relevant for geothermal energy production, or modeling thermal spallation drilling in new rock types. Nevertheless, with sufficient computational resources, Weibull models could be validated in the absence of experimental data by explicit small-scale simulations that fully resolve rock grains. This presentation will discuss how high-fidelity simulations can be used to inform Weibull models of thermal spallation, and what these simulations reveal about the processes driving spallation at the grain-scale - in particular, the role that inter-grain boundaries and micro-pores play in the

  19. Material selection for spallation neutron source windows

    Energy Technology Data Exchange (ETDEWEB)

    Sordo, F. [ETSII/Universidad Politecnica de Madrid, J. Gutierrez Abascal, 2-28006 Madrid (Spain); Abanades, A. [ETSII/Universidad Politecnica de Madrid, J. Gutierrez Abascal, 2-28006 Madrid (Spain)], E-mail: abanades@etsii.upm.es; Lafuente, A.; Martinez-Val, J.M. [ETSII/Universidad Politecnica de Madrid, J. Gutierrez Abascal, 2-28006 Madrid (Spain); Perlado, M. [Instituto de Fusion Nuclear (DENIM)/ETSII/Universidad Politecnica, Madrid, J. Gutierrez Abascal, 2-28006 Madrid (Spain)

    2009-11-15

    High performance neutron sources are being proposed for many scientific and industrial applications, ranging from material studies, hybrid reactors and transmutation of nuclear wastes. In the case of transmutation of nuclear wastes, accelerator driven systems (ADS) are considered as one of the main technical options for such purpose. In ADS a high performance spallation neutron source becomes an essential element for its operation and control. This spallation source must fulfil very challenging nuclear and thermo-mechanical requirements, because of the high neutron rates needed in ADS. The material selection for this key component becomes of paramount importance, particularly the source window that separates the vacuum accelerator tube from the spallation material where the accelerated protons impinge. In this paper, an integral analysis of spallation sources is done, taking as a reference the projects in this field proposal in the framework of European projects. Our analysis and calculations show that titanium and vanadium alloys are more suitable than steel as structural material for an industrial ADS beam window, mostly due to its irradiation damage resistance.

  20. The Spallation Neutron Source Beam Commissioning and Initial Operations

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, Stuart [Argonne National Lab. (ANL), Argonne, IL (United States); Aleksandrov, Alexander V. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Allen, Christopher K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Assadi, Saeed [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bartoski, Dirk [University of Texas, Houston, TX (United States). Anderson Cancer Center; Blokland, Willem [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Casagrande, F. [Michigan State Univ., East Lansing, MI (United States); Campisi, I. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Chu, C. [Michigan State Univ., East Lansing, MI (United States); Cousineau, Sarah M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Crofford, Mark T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Danilov, Viatcheslav [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Deibele, Craig E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Dodson, George W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Feshenko, A. [Inst. for Nuclear Research (INR), Moscow (Russian Federation); Galambos, John D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Han, Baoxi [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hardek, T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Holmes, Jeffrey A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Holtkamp, N. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Howell, Matthew P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jeon, D. [Inst. for Basic Science, Daejeon (Korea); Kang, Yoon W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kasemir, Kay [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kim, Sang-Ho [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kravchuk, L. [Institute for Nuclear Research (INR), Moscow (Russian Federation); Long, Cary D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); McManamy, T. [McManamy Consulting, Inc., Middlesex, MA (United States); Pelaia, II, Tom [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Piller, Chip [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Plum, Michael A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pogge, James R. [Tennessee Technological Univ., Cookeville, TN (United States); Purcell, John David [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shea, T. [European Spallation Source, Lund (Sweden); Shishlo, Andrei P [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sibley, C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stockli, Martin P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stout, D. [Michigan State Univ., East Lansing, MI (United States); Tanke, E. [European Spallation Source, Lund (Sweden); Welton, Robert F [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhang, Y. [Michigan State Univ., East Lansing, MI (United States); Zhukov, Alexander P [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-09-01

    The Spallation Neutron Source (SNS) accelerator delivers a one mega-Watt beam to a mercury target to produce neutrons used for neutron scattering materials research. It delivers ~ 1 GeV protons in short (< 1 us) pulses at 60 Hz. At an average power of ~ one mega-Watt, it is the highest-powered pulsed proton accelerator. The accelerator includes the first use of superconducting RF acceleration for a pulsed protons at this energy. The storage ring used to create the short time structure has record peak particle per pulse intensity. Beam commissioning took place in a staged manner during the construction phase of SNS. After the construction, neutron production operations began within a few months, and one mega-Watt operation was achieved within three years. The methods used to commission the beam and the experiences during initial operation are discussed.

  1. BEAM INSTRUMENTATION FOR THE SPALLATION NEUTRON SOURCE RING.

    Energy Technology Data Exchange (ETDEWEB)

    WITKOVER,R.L.; CAMERON,P.R.; SHEA,T.J.; CONNOLLY,R.C.; KESSELMAN,M.

    1999-03-29

    The Spallation Neutron Source (SNS) will be constructed by a multi-laboratory collaboration with BNL responsible for the transfer lines and ring. [1] The 1 MW beam power necessitates careful monitoring to minimize un-controlled loss. This high beam power will influence the design of the monitors in the high energy beam transport line (HEBT) from linac to ring, in the ring, and in the ring-to-target transfer line (RTBT). The ring instrumentation must cover a 3-decade range of beam intensity during accumulation. Beam loss monitoring will be especially critical since un-controlled beam loss must be kept below 10{sup -4}. A Beam-In-Gap (BIG) monitor is being designed to assure out-of-bucket beam will not be lost in the ring.

  2. Management of Tritium in European Spallation Source

    DEFF Research Database (Denmark)

    Ene, Daniela; Andersson, Kasper Grann; Jensen, Mikael

    2015-01-01

    The European Spallation Source (ESS) will produce tritium via spallation and activation processes during operational activities. Within the location of ESS facility in Lund, Sweden site it is mandatory to demonstrate that the management strategy of the produced tritium ensures the compliance...... with the country regulation criteria. The aim of this paper is to give an overview of the different aspects of the tritium management in ESS facility. Besides the design parameter study of the helium coolant purification system of the target the consequences of the tritium releasing into the environment were also...... analyzed. Calculations shown that the annual release of tritium during the normal operations represents a small fraction from the estimated total dose. However, more refined calculations of migration of activated-groundwater should be performed for higher hydraulic conductivities, with the availability...

  3. Neutronics of pulsed spallation neutron sources

    CERN Document Server

    Watanabe, N

    2003-01-01

    Various topics and issues on the neutronics of pulsed spallation neutron sources, mainly for neutron scattering experiments, are reviewed to give a wide circle of readers a better understanding of these sources in order to achieve a high neutronic performance. Starting from what neutrons are needed, what the spallation reaction is and how to produce slow-neutrons more efficiently, the outline of the target and moderator neutronics are explained. Various efforts with some new concepts or ideas have already been devoted to obtaining the highest possible slow-neutron intensity with desired pulse characteristics. This paper also reviews the recent progress of such efforts, mainly focused on moderator neutronics, since moderators are the final devices of a neutron source, which determine the source performance. Various governing parameters for neutron-pulse characteristics such as material issues, geometrical parameters (shape and dimensions), the target-moderator coupling scheme, the ortho-para-hydrogen ratio, po...

  4. Simulation of a beam rotation system for a spallation source

    Directory of Open Access Journals (Sweden)

    Tibor Reiss

    2015-04-01

    Full Text Available With a nominal beam power of nearly 1 MW on target, the Swiss Spallation Neutron Source (SINQ, ranks among the world’s most powerful spallation neutron sources. The proton beam transport to the SINQ target is carried out exclusively by means of linear magnetic elements. In the transport line to SINQ the beam is scattered in two meson production targets and as a consequence, at the SINQ target entrance the beam shape can be described by Gaussian distributions in transverse x and y directions with tails cut short by collimators. This leads to a highly nonuniform power distribution inside the SINQ target, giving rise to thermal and mechanical stresses. In view of a future proton beam intensity upgrade, the possibility of homogenizing the beam distribution by means of a fast beam rotation system is currently under investigation. Important aspects which need to be studied are the impact of a rotating proton beam on the resulting neutron spectra, spatial flux distributions and additional—previously not present—proton losses causing unwanted activation of accelerator components. Hence a new source description method was developed for the radiation transport code MCNPX. This new feature makes direct use of the results from the proton beam optics code TURTLE. Its advantage to existing MCNPX source options is that all phase space information and correlations of each primary beam particle computed with TURTLE are preserved and transferred to MCNPX. Simulations of the different beam distributions together with their consequences in terms of neutron production are presented in this publication. Additionally, a detailed description of the coupling method between TURTLE and MCNPX is provided.

  5. Decommissioning Plan for European Spallation Source

    Directory of Open Access Journals (Sweden)

    Ene Daniela

    2017-01-01

    Full Text Available This paper is a survey of the European Spallation Source initial decommissioning plan developed in compliance with Swedish Regulatory Authority requirements. The report outlines the decommissioning strategy selected and the baseline plan for decommissioning. Types and quantities of radioactive waste estimated to be generated at the final shut-down of the facility are further provided. The paper ends up with the analysis of the key elements of the decommissioning plan and the recommendations to the ESS management team..

  6. Outline of spallation neutron source engineering

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Noboru [Center for Neutron Science, Tokai Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan)

    2001-01-01

    Slow neutrons such as cold and thermal neutrons are unique probes which can determine structures and dynamics of condensed matter in atomic scale. The neutron scattering technique is indispensable not only for basic sciences such as condensed matter research and life science, but also for basic industrial technology in 21 century. It is believed that to survive in the science-technology competition in 21 century would be almost impossible without neutron scattering. However, the intensity of neutrons presently available is much lower than synchrotron radiation sources, etc. Thus, R and D of intense neutron sources become most important. The High-Intensity Proton Accelerator Project is now being promoted jointly by Japan Atomic Energy Research Institute and High Energy Accelerator Research Organization, but there has so far been no good text which covers all the aspects of pulsed spallation neutron sources. The present review was prepare aiming at giving a better understanding on pulsed spallation neutron sources not only to neutron source researchers but also more widely to neutron scattering researchers and accelerator scientists in this field. The contents involve, starting from what is neutron scattering and what neutrons are necessary for neutron scattering, what is the spallation reaction, how to produce neutrons required for neutron scattering more efficiently, target-moderator-reflector neutronics and its engineering, shielding, target station, material issues, etc. The author have engaged in R and D of pulsed apallation neutron sources and neutron scattering research using them over 30 years. The present review is prepared based on the author's experiences with useful information obtained through ICANS collaboration and recent data from the JSNS (Japanese Spallation Neutron Source) design team. (author)

  7. Decommissioning Plan for European Spallation Source

    Science.gov (United States)

    Ene, Daniela

    2017-09-01

    This paper is a survey of the European Spallation Source initial decommissioning plan developed in compliance with Swedish Regulatory Authority requirements. The report outlines the decommissioning strategy selected and the baseline plan for decommissioning. Types and quantities of radioactive waste estimated to be generated at the final shut-down of the facility are further provided. The paper ends up with the analysis of the key elements of the decommissioning plan and the recommendations to the ESS management team..

  8. INJECTION CHOICE FOR SPALLATION NEUTRON SOURCE RING.

    Energy Technology Data Exchange (ETDEWEB)

    WEI,J.; BEEBE-WANG,J.; BLASKIEWICZ,M.; BRODOWSKI,J.; FEDOTOV,A.; GARDNER,C.; LEE,Y.Y.; RAPARIA,D.; DANILOV,V.; HOLMES,J.; PRIOR,C.; REES,G.; MACHIDA,S.

    2001-06-18

    Injection is key in the low-loss design of high-intensity proton facilities like the Spallation Neutron Source (SNS). During the design of both the accumulator and the rapid-cycling-synchrotron version of the SNS, extensive comparison has been made to select injection scenarios that satisfy SNS's low-loss design criteria. This paper presents issues and considerations pertaining to the final choice of the SNS injection systems.

  9. Decay heat calculations for a 500 kW W–Ta spallation target

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Quanzhi, E-mail: qzhyu@iphy.ac.cn [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Lu, Youlian; Hu, Zhiliang; Zhou, Bin [Dongguan Campus, Institute of High Energy Physics, Chinese Academy of Sciences, Dongguan 523800 (China); Dongguan Neutron Science Center, Dongguan 523800 (China); Yin, Wen; Liang, Tianjiao [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)

    2015-05-15

    The China Spallation Neutron Source (CSNS) is a short-pulsed neutron scattering facility. The beam power is designed to be 100 kW in Phase I, with the capability of upgrading to 500 kW. Tantalum (Ta)-cladded tungsten (W) was chosen as the spallation target due to its high neutron yield. Ta claddings can solve the problem of the corrosiveness of W plates, although they produce high decay heat after intense irradiation. This paper presents the decay heat distributions and evolutions for the future upgraded 500 kW W–Ta spallation target. The calculations are performed using the MCNPX2.5 Monte Carlo code and the CINDER’90 activation code. The decay heat distributions show that for the W plates, decay heat is mainly produced via the spallation reaction process, whereas for the Ta claddings, it is mainly produced via the neutron capture process. An effective method of reducing the decay heat in the W–Ta target is also presented and discussed.

  10. Spallation reactions studied with 4-detector arrays

    Indian Academy of Sciences (India)

    J Galin

    2001-07-01

    Recently there has been a renewed interest in the study of spallation reactions in basic nuclear physics as well as in potential applications. Spallation reactions induced by light projectiles (protons, antiprotons, pions, etc.) in the GeV range allow the formation of hot nuclei which do not suffer the collective excitations (compression, rotation, deformation) unavoidable when using massive projectiles. Such nuclei provide an ideal testbench for probing their decay as a function of excitation energy. In these investigations, 4-detector arrays for charged particles and neutrons play a major role in the event-by-event sorting according to the excitation energy of the nucleus. Spallation reactions induced on heavy nuclei allow the conversion of the incident GeV proton into several tens of evaporated neutrons. The neutron production in thick targets has been investigated in great detail thanks to the use of high efficiency neutron detector arrays. When scattered on samples of inert or biological materials, these neutrons can be used to study details of the material structure. They could also be utilized for the transmutation of long-lived nuclear wastes or for the feeding of sub-critical nuclear reactors. The role of different types of multi-detector arrays is highlighted in this paper. Several references are also given for different uses of high efficiency neutron detectors in other contexts.

  11. Establishment of quality, reliability and design standards for low, medium, and high power microwave hybrid microcircuits

    Science.gov (United States)

    Robinson, E. A.

    1973-01-01

    Quality, reliability, and design standards for microwave hybrid microcircuits were established. The MSFC Standard 85M03926 for hybrid microcircuits was reviewed and modifications were generated for use with microwave hybrid microcircuits. The results for reliability tests of microwave thin film capacitors, transistors, and microwave circuits are presented. Twenty-two microwave receivers were tested for 13,500 unit hours. The result of 111,121 module burn-in and operating hours for an integrated solid state transceiver module is reported.

  12. Room-temperature LINAC structures for the spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Billen, J. H. (James H.); Young, L. M. (Lloyd M.); Kurennoy, S. (Sergey); Crandall, K. R. (Kenneth R.)

    2001-04-01

    Los Alamos National Laboratory is building room-temperature rf accelerating structures for the Spallation Neutron Source (SNS). These structures, for H{sup -} ions, consist of six 402.5-MHz, 2-MW drift-tube linac (DTL) tanks from 2.5 to 87 MeV followed by four 805-MHz, 4-MW coupled-cavity linac (CCL) modules to 186 MeV. The DTL uses permanent magnet quadrupoles inside the drift tubes arranged in a 6{beta}{lambda} FFODDO lattice with every third drift tube available for diagnostics and steering. The CCL uses a 13{beta}{lambda} FODO electromagnetic quadrupole lattice. Diagnostics and magnets occupy the 2.5{beta}{lambda} spaces between 8-cavity segments. This paper discusses design of the rf cavities and low-power modeling work.

  13. The Effect of Beam Intensity on Temperature Distribution in ADS Windowless Lead-Bismuth Eutectic Spallation Target

    Directory of Open Access Journals (Sweden)

    Jie Liu

    2014-01-01

    Full Text Available The spallation target is the component coupling the accelerator and the reactor and is regarded as the “heart” of the accelerator driven system (ADS. Heavy liquid metal lead-bismuth eutectic (LBE is served as core coolant and spallation material to carry away heat deposition of spallation reaction and produce high flux neutron. So it is very important to study the heat transfer process in the target. In this paper, the steady-state flow pattern has been numerically obtained and taken as the input for the nuclear physics calculation, and then the distribution of the extreme large power density of the heat load is imported back to the computational fluid dynamics as the source term in the energy equation. Through the coupling, the transient and steady-state temperature distribution in the windowless spallation target is obtained and analyzed based on the flow process and heat transfer. Comparison of the temperature distribution with the different beam intensity shows that its shape is the same as broken wing of the butterfly. Nevertheless, the maximum temperature as well as the temperature gradient is different. The results play an important role and can be applied to the further design and optimization of the ADS windowless spallation target.

  14. Surface modification to prevent oxide scale spallation

    Science.gov (United States)

    Stephens, Elizabeth V; Sun, Xin; Liu, Wenning; Stevenson, Jeffry W; Surdoval, Wayne; Khaleel, Mohammad A

    2013-07-16

    A surface modification to prevent oxide scale spallation is disclosed. The surface modification includes a ferritic stainless steel substrate having a modified surface. A cross-section of the modified surface exhibits a periodic morphology. The periodic morphology does not exceed a critical buckling length, which is equivalent to the length of a wave attribute observed in the cross section periodic morphology. The modified surface can be created using at least one of the following processes: shot peening, surface blasting and surface grinding. A coating can be applied to the modified surface.

  15. Muon-induced spallation backgrounds in DUNE

    Science.gov (United States)

    Zhu, Guanying; Li, Shirley; Beacom, John

    2017-01-01

    Galactic supernovae are rare, just a few per century, so it is important to be prepared. If we are, then the long-baseline detector DUNE could detect thousands of events, compared to the tens from SN 1987A. An important question is backgrounds from muon-induced spallation reactions. We simulate particle energy-loss processes in liquid argon, and compare relevant isotope yields with those in the water-Cherenkov detector SuperK. Our approach will help optimize the design of DUNE and further benefit the study of supernova neutrinos. GZ, SWL, and JFB are supported by NSF Grant PHY-1404311.

  16. Spallation Source Modelling for an ADS Using the MCNPX and GEANT4 Packages for Sensitivity Analysis of Reactivity

    Science.gov (United States)

    Antolin, M. Q.; Marinho, F.; Palma, D. A. P.; Martinez, A. S.

    2014-04-01

    A simulation for the time evolution of the MYRRHA conceptual reactor was developed. The SERPENT code was used to simulate the nuclear fuel depletion and the spallation source which drives the system was simulated using both MCNPX and GEANT4 packages. The obtained results for the neutron energy spectrum from the spallation are coherent with each other and were used as input for the SERPENT code which simulated a constant power operation regime. The obtained results show that the criticality of the system is not sensitive to the spallation models employed and only relative small deviations with respect to the inverse kinetic model coming from the point kinetic equations proposed by Gandini were observed.

  17. Fundamental physics possibilities at the European Spallation Source

    DEFF Research Database (Denmark)

    Klinkby, Esben Bryndt; Batkov, Konstantin; Mezei, Ferenc;

    2016-01-01

    The construction of the European Spallation has recently started in Lund, Sweden.In addition to the neutron scattering instruments the ESS is designed to serve, the constructionof a new spallation source opens up new possibilities for fundamental physics experiments. Inthis paper some of the poss...

  18. The Beam Delivery System of the European Spallation Source

    DEFF Research Database (Denmark)

    Thomsen, Heine Dølrath; Møller, Søren Pape

    The European Spallation Source (ESS) will apply a fast beam scanning system to redistribute the proton beam transversely across the spallation target surface. The system operates at sweep frequencies of tens of kHz and efficiently evens out the time-averaged beam intensity within a nominal beam...

  19. QGSM development for spallation reactions modeling

    Directory of Open Access Journals (Sweden)

    Gudima K.K.

    2012-12-01

    Full Text Available The growing interest in spallation neutron sources, accelerator-driven systems, R&D of rare isotope beams, and development of external beam radiation therapy necessitated the improvement of nuclear reaction models for both stand-alone codes for the analysis of nuclear reactions and event generators within the Monte Carlo transport systems for calculations of interactions of high-energy particles with matter in a wide range of energy and in arbitrary 3D geometry of multicomponent targets. The exclusive approach to the description of nuclear reactions is the most effective for detailed calculation of inelastic interactions with atomic nuclei. It provides the correct description of particle production, single- and double-differential spectra, recoil, and fission product yields. This approach has been realized in the Quark Gluon String Model (QGSM for nuclear reactions induced by photons, hadrons, and high energy heavy ions. In this article, improved versions of the QGSM model and a corresponding code have been developed tested and bench marked against experimental data for neutron production in spallation reactions on thin and thick targets in the energy range from a few MeV to several GeV/nucleon.

  20. QGSM development for spallation reactions modeling

    Science.gov (United States)

    Baznat, M. I.; Chigrinov, S. E.; Gudima, K. K.

    2012-12-01

    The growing interest in spallation neutron sources, accelerator-driven systems, R&D of rare isotope beams, and development of external beam radiation therapy necessitated the improvement of nuclear reaction models for both stand-alone codes for the analysis of nuclear reactions and event generators within the Monte Carlo transport systems for calculations of interactions of high-energy particles with matter in a wide range of energy and in arbitrary 3D geometry of multicomponent targets. The exclusive approach to the description of nuclear reactions is the most effective for detailed calculation of inelastic interactions with atomic nuclei. It provides the correct description of particle production, single- and double-differential spectra, recoil, and fission product yields. This approach has been realized in the Quark Gluon String Model (QGSM) for nuclear reactions induced by photons, hadrons, and high energy heavy ions. In this article, improved versions of the QGSM model and a corresponding code have been developed tested and bench marked against experimental data for neutron production in spallation reactions on thin and thick targets in the energy range from a few MeV to several GeV/nucleon.

  1. Spallation studies on shock loaded uranium

    Energy Technology Data Exchange (ETDEWEB)

    Tonks, D.L.; Hixson, R.; Gustavsen, R.L.; Vorthman, J.E.; Kelly, A.; Zurek, A.K.; Thissel, W.R. [Los Alamos National Lab., NM (United States)

    1997-12-31

    Uranium samples at two different purity levels were used for spall strength measurements at three different stress levels. A 50 mm single-stage gas-gun was used to produce planar impact conditions using Z-cut quartz impactors. Samples of depleted uranium were taken from very high purity material and from material that had 300 ppm of carbon added. A pair of shots was done for each impact strength, one member of the pair with VISAR diagnostics and the second with soft recovery for metallographical examination. A series of increasing final stress states were chosen to effectively freeze the microstructural damage at three places in the development to full spall separation. This allowed determination of the dependence of spall mechanisms on stress level and sample purity. This report will discuss both the results of the metallurgical examination of soft recovered samples and the modeling of the free surface VISAR data. The micrographs taken from the recovered samples show brittle cracking as the spallation failure mechanism. Deformation induced twins are plentiful and obviously play a role in the spallation process. The twins are produced in the initial shock loading and, so, are present already before the fracture process begins. The 1 d characteristics code CHARADE has been used to model the free surface VISAR data.

  2. Studies Performed in Preparation for the Spallation Neutron Source Accumulator Ring Commissioning

    CERN Document Server

    Cousineau, Sarah M; Henderson, Stuart; Holmes, Jeffrey Alan; Plum, Michael

    2005-01-01

    The Spallation Neutron Source accumulator ring will compress 1.5?1014, 1 GeV protons from a 1 ms bunch train to a single 695 ns proton bunch for use in neutron spallation. Due to the high beam power, unprecedented control of beam loss will be required in order to control radiation and allow for hands-on maintenance in most areas of the ring. A number of detailed investigations have been performed to understand the primary sources of beam loss and to predict and mitigate problems associated with radiation hot spots in the ring. The ORBIT particle tracking code is used to perform realistic simulations of the beam accumulation in the ring, including detailed modeling of the injection system, transport through the measured magnet fields including higher order multipoles, and beam loss and collimation. In this paper we present the results of a number of studies performed in preparation for the 2006 commissioning of the accumulator ring.

  3. THERMAL HYDRAULIC ANALYSIS OF A LIQUID-METAL-COOLED NEUTRON SPALLATION TARGET

    Energy Technology Data Exchange (ETDEWEB)

    W. GREGORY; R. MARTIN; T. VALACHOVIC

    2000-07-01

    We have carried out numerical simulations of the thermal hydraulic behavior of a neutron spallation target where liquid metal lead-bismuth serves as both coolant and as a neutron spallation source. The target is one of three designs provided by the Institute of Physics and Power Engineering (IPPE) in Russia. This type of target is proposed for Accelerator-driven Transmutation of Waste (ATW) to eliminate plutonium from hazardous fission products. The thermal hydraulic behavior was simulated by use of a commercial CFD computer code called CFX. Maximum temperatures in the diaphragm window and in the liquid lead were determined. In addition the total pressure drop through the target was predicted. The results of the CFX analysis were close to those results predicted by IPPE in their preliminary analysis.

  4. Cost Optimisation of an Instrument Suite at an Accelerator-Driven Spallation Source

    CERN Document Server

    Bentley, P M

    2016-01-01

    This artcile presents an optimisation of performance and cost of neutron scattering instrumentation at the European Spallation Source. This is done by trading detailed cost functions against beam transmission functions in a multi-dimensional, yet simple, parameter space. On the one hand, the neutron guide cost increases as a power of the desired beam divergence, and inversely with the minimum wavelength, due to the supermirror coating needed. On the other hand, the more neutrons are transported to the instrument the greater are the shielding costs to deal with the gamma rays that result from the eventual absorption of the neutrons. There are additional factors in that many of the parameters defining the neutron guide geometry are continuous variables, and the straightness of the guide increases the transmission of high energy spallation products, which affect the specifications of particularly heavy hardware, such as heavy shutters and additional shielding, beam stops etc. Over the suite of 16 instruments, a ...

  5. ENGINEERING DESIGN OF THE EURISOL MULTI-MW SPALLATION TARGET

    CERN Document Server

    Adonai Herrera-Martinez*, Yacine Kadi, Morteza Ashrafi-Nik, Karel Samec, Janis Freibergs, Ernests Platacis

    The European Isotope Separation On-Line Radioactive Ion Beam project (EURISOL) is set to design the ‘next-generation’ European Isotope Separation On-Line (ISOL) Radioactive Ion Beam (RIB) facility. It will extend and amplify current research on nuclear physics, nuclear astrophysics and fundamental interactions beyond the year 2010. In EURISOL, four target stations are foreseen, three direct targets of approximately 100 kW of beam power and one multi-MW target assembly, all driven by a high-power particle accelerator. In this high power target station, high-intensity RIBs of neutron-rich isotopes will be obtained by inducing fission in several actinide targets surrounding a liquid metal spallation neutron source. This article summarises the work carried out within Task 2 of the EURISOL Design Study, with special attention to the coupled neutronics of the mercury proton-to-neutron converter and the fission targets. The overall performance of the facility, which will sustain fast neutron fluxes of the order ...

  6. rf improvements for Spallation Neutron Source H-ion source

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Yoon W [ORNL; Fuja, Raymond E [ORNL; Goulding, Richard Howell [ORNL; Hardek, Thomas W [ORNL; Lee, Sung-Woo [ORNL; McCarthy, Mike [ORNL; Piller, Chip [ORNL; Shin, Ki [ORNL; Stockli, Martin P [ORNL; Welton, Robert F [ORNL

    2010-01-01

    The Spallation Neutron Source at Oak Ridge National Laboratory is ramping up the accelerated proton beam power to 1.4 MW and just reached 1 MW. The rf-driven multicusp ion source that originates from the Lawrence Berkeley National Laboratory has been delivering 38 mA H beam in the linac at 60 Hz, 0.9 ms. To improve availability, a rf-driven external antenna multicusp ion source with a water-cooled ceramic aluminum nitride AlN plasma chamber is developed. Computer modeling and simulations have been made to analyze and optimize the rf performance of the new ion source. Operational statistics and test runs with up to 56 mA medium energy beam transport beam current identify the 2 MHz rf system as a limiting factor in the system availability and beam production. Plasma ignition system is under development by using a separate 13 MHz system. To improve the availability of the rf power system with easier maintenance, we tested a 70 kV isolation transformer for the 80 kW, 6% duty cycle 2 MHz amplifier to power the ion source from a grounded solid-state amplifier. 2010 American Institute of Physics.

  7. Engineering design of the EURISOL multi-MW spallation target

    CERN Document Server

    Herrera-Martínez, A; Ashrafi-Nik, M; Samec, K; Freibergs, J; Platacis, E

    2007-01-01

    The European Isotope Separation On-Line Radioactive Ion Beam project (EURISOL) is set to design the 'next-generation' European Isotope Separation On-Line (ISOL) Radioactive Ion Beam (RIB) facility. It will extend and amplify current research on nuclear physics, nuclear astrophysics and fundamental interactions beyond the year 2010. In EURISOL, four target stations are foreseen, three direct targets of approximately 100 kW of beam power and one multi-MW target assembly, all driven by a high-power particle accelerator. In this high power target station, high-intensity RIBs of neutron-rich isotopes will be obtained by inducing fission in several actinide targets surrounding a liquid metal spallation neutron source. This article summarises the work carried out within Task 2 of the EURISOL Design Study, with special attention to the coupled neutronics of the mercury proton-to-neutron converter and the fission targets. The overall performance of the facility, which will sustain fast neutron fluxes of the order of 1...

  8. High power neutron production targets

    Energy Technology Data Exchange (ETDEWEB)

    Wender, S. [Los Alamos National Lab., NM (United States)

    1996-06-01

    The author describes issues of concern in the design of targets and associated systems for high power neutron production facilities. The facilities include uses for neutron scattering, accelerator driven transmutation, accelerator production of tritium, short pulse spallation sources, and long pulse spallation sources. Each of these applications requires a source with different design needs and consequently different implementation in practise.

  9. Experimental measurement of surface temperatures during flame-jet induced thermal spallation

    Science.gov (United States)

    Wilkinson, M. A.; Tester, J. W.

    1993-01-01

    Thermal spallation is a method whereby the surface of a rock is rapidly heated causing small (100 1000 μm) flakes or spalls, to form. When applied to drilling, a supersonic, high temperature (2600 K) gas jet is directed at the rock to provide the heat source and sweep away the spalls. Previous studies of thermal spallation drilling indicate that penetration rates of up to 30 m/hr (100 ft/hr), approximately ten times greater than commonly obtained using conventional rotary mechanical methods, can be achieved in competent, non-fractured hard rock such as granite. A total direct operating cost for drilling in granite using a flame-jet spallation drill was estimated by Browning (1981) to be approximately 9/m in 1991 (about 3/ft) compared to “trouble-free” well drilling costs for conventional rotary methods in similar rock to depths of 3 to 7 km (10000 to 21000 ft) of 300 to 900/m (100 to 300/ft) (Tester and Herzog, 1990, 1992). The Browning estimates for spallation drilling are obviously optimistic in that they don't include capital costs for the rig and associated hardware. However, the substantially higher penetration rates, significantly reduced wear of downhole components, and the high efficiency of rock communition in comparison to rotary methods suggest that substantial cost reductions could be possible in deep drilling applications. For example, in the construction of hot dry rock geothermal power plants where rotary mechanical methods are used for well drilling to depths of (4 to 5 km), about half of the initial capital cost would be required for well drilling alone (Tester and Herzog, 1992). The current study has focused on gaining a better understanding of both the rock failure mechanism that occurs during thermal spallation and the heat transfer from the gas jet to the rock surface. Rock mechanics modeling leads to an expression for the surface temperature during spallation as a function of rock physical properties and the incident heat flux. Surface

  10. Estimation of thermochemical behavior of spallation products in mercury target

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, Kaoru; Kaminaga, Masanori; Haga, Katsuhiro; Kinoshita, Hidetaka; Aso, Tomokazu; Teshigawara, Makoto; Hino, Ryutaro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2002-02-01

    In order to examine the radiation safety of a spallation mercury target system, especially source term evaluation, it is necessary to clarify the chemical forms of spallation products generated by spallation reaction with proton beam. As for the chemical forms of spallation products in mercury that involves large amounts of spallation products, these forms were estimated by using the binary phase diagrams and the thermochemical equilibrium calculation based on the amounts of spallation product. Calculation results showed that the mercury would dissolve Al, As, B, Be, Bi, C, Co, Cr, Fe, Ga, Ge, Ir, Mo, Nb, Os, Re, Ru, Sb, Si, Ta, Tc, V and W in the element state, and Ag, Au, Ba, Br, Ca, Cd, Ce, Cl, Cs, Cu, Dy, Er, Eu, F, Gd, Hf, Ho, I, In, K, La, Li, Lu, Mg, Mn, Na, Nd, Ni, O, Pb, Pd, Pr, Pt, Rb, Rh, S, Sc, Se, Sm, Sn, Sr, Tb, Te, Ti, Tl, Tm, Y, Yb, Zn and Zr in the form of inorganic mercury compounds. As for As, Be, Co, Cr, Fe, Ge, Ir, Mo, Nb, Os, Pt, Re, Ru, Se, Ta, V, W and Zr, precipitation could be occurred when increasing the amounts of spallation products with operation time of the spallation target system. On the other hand, beryllium-7 (Be-7), which is produced by spallation reaction of oxygen in the cooling water of a safety hull, becomes the main factor of the external exposure to maintain the cooling loop. Based on the thermochemical equilibrium calculation to Be-H{sub 2}O binary system, the chemical forms of Be in the cooling water were estimated. Then the Be could exist in the form of cations such as BeOH{sup +}, BeO{sup +} and Be{sup 2+} under the condition of less than 10{sup -8} of the Be mole fraction in the cooling water. (author)

  11. Determination of spallation neutron flux through spectral adjustment techniques

    Energy Technology Data Exchange (ETDEWEB)

    Mosby, M.A., E-mail: mosbym@lanl.gov; Engle, J.W.; Jackman, K.R.; Nortier, F.M.; Birnbaum, E.R.

    2016-08-15

    The Los Alamos Isotope Production Facility (IPF) creates medical isotopes using a proton beam impinged on a target stack. Spallation neutrons are created in the interaction of the beam with target. The use of these spallation neutrons to produce additional radionuclides has been proposed. However, the energy distribution and magnitude of the flux is not well understood. A modified SAND-II spectral adjustment routine has been used with radioactivation foils to determine the differential neutron fluence for these spallation neutrons during a standard IPF production run.

  12. Determination of spallation neutron flux through spectral adjustment techniques

    Science.gov (United States)

    Mosby, M. A.; Engle, J. W.; Jackman, K. R.; Nortier, F. M.; Birnbaum, E. R.

    2016-08-01

    The Los Alamos Isotope Production Facility (IPF) creates medical isotopes using a proton beam impinged on a target stack. Spallation neutrons are created in the interaction of the beam with target. The use of these spallation neutrons to produce additional radionuclides has been proposed. However, the energy distribution and magnitude of the flux is not well understood. A modified SAND-II spectral adjustment routine has been used with radioactivation foils to determine the differential neutron fluence for these spallation neutrons during a standard IPF production run.

  13. Role of multifragmentation in spallation reactions

    CERN Document Server

    Botvina, A S

    2008-01-01

    In nuclear reactions induced by hadrons and ions of high energies, nuclei can disintegrate into many fragments during a short time (~100 fm/c). This phenomenon known as nuclear multifragmentation was under intensive investigation last 20 years. It was established that multifragmentation is an universal process taking place in all reactions when the excitation energy transferred to nuclei is high enough, more than 3 MeV per nucleon, independently on the initial dynamical stage of the reactions. Very known compound nucleus decay processes (sequential evaporation and fission), which are usual for low energies, disappear and multifragmentation dominates at high excitation energy. For this reason, calculation of multifragmentation must be carried on in all cases when production of highly excited nuclei is expected, including spallation reactions. From the other hand, one can consider multifragmentation as manifestation of the liquid-gas phase transition in finite nuclei. This gives way for studying nuclear matter ...

  14. Measurements of neutron spallation cross section. 2

    Energy Technology Data Exchange (ETDEWEB)

    Kim, E.; Nakamura, T. [Tohoku Univ., Sendai (Japan). Cyclotron and Radioisotope Center; Imamura, M.; Nakao, N.; Shibata, S.; Uwamino, Y.; Nakanishi, N.; Tanaka, Su.

    1997-03-01

    Neutron spallation cross section of {sup 59}Co(n,xn){sup 60-x}Co, {sup nat}Cu(n,sp){sup 56}Mn, {sup nat}Cu(n,sp){sup 58}Co, {sup nat}Cu(n,xn){sup 60}Cu, {sup nat}Cu(n,xn){sup 61}Cu and {sup nat}Cu(n,sp){sup 65}Ni was measured in the quasi-monoenergetic p-Li neutron fields in the energy range above 40 MeV which have been established at three AVF cyclotron facilities of (1) INS of Univ. of Tokyo, (2) TIARA of JAERI and (3) RIKEN. Our experimental data were compared with the ENDF/B-VI high energy file data by Fukahori and the calculated cross section data by Odano. (author)

  15. Mechanical Engineering of the Linac for the Spallation Neutron Source

    Energy Technology Data Exchange (ETDEWEB)

    Bultman, N.K.; Chen, Z.; Collier, M.; Erickson, J.L.; Guthrie, A.; Hunter, W.T.; Ilg, T.; Meyer, R.K.; Snodgrass, N.L.

    1999-03-29

    The linac for the Spallation Neutron Source (SNS) Project will accelerate an average current of 1 mA of H{sup {minus}} ions from 20 MeV to 1GeV for injection into an accumulator ring. The linac will be an intense source of H{sup {minus}} ions and as such requires advanced design techniques to meet project technical goals as well as to minimize costs. The DTL, CCDTL and CCL are 466m long and operate at 805 MHz with a maximum H{sup {minus}} input current of 28 mA and 7% rf duty factor. The Drift Tube Linac is a copper-plated steel structure using permanent magnetic quadrupoles. The Coupled-Cavity portions are brazed copper structures and use electromagnetic quads. RF losses in the copper are 80 MW, with total rf power supplied by 52 klystrons. Additionally, the linac is to be upgraded to the 2- and 4-MW beam power levels with no increase in duty factor. The authors give an overview of the linac mechanical engineering effort and discuss the special challenges and status of the effort.

  16. Strain rate effects for spallation of concrete

    Directory of Open Access Journals (Sweden)

    Häussler-Combe Ulrich

    2015-01-01

    Full Text Available Appropriate triaxial constitutive laws are the key for a realistic simulation of high speed dynamics of concrete. The strain rate effect is still an open issue within this context. In particular the question whether it is a material property – which can be covered by rate dependent stress strain relations – or mainly an effect of inertia is still under discussion. Experimental and theoretical investigations of spallation of concrete specimen in a Hopkinson Bar setup may bring some evidence into this question. For this purpose the paper describes the VERD model, a newly developed constitutive law for concrete based on a damage approach with included strain rate effects [1]. In contrast to other approaches the dynamic strength increase is not directly coupled to strain rate values but related to physical mechanisms like the retarded movement of water in capillary systems and delayed microcracking. The constitutive law is fully triaxial and implemented into explicit finite element codes for the investigation of a wide range of concrete structures exposed to impact and explosions. The current setup models spallation experiments with concrete specimen [2]. The results of such experiments are mainly related to the dynamic tensile strength and the crack energy of concrete which may be derived from, e.g., the velocity of spalled concrete fragments. The experimental results are compared to the VERD model and two further constitutive laws implemented in LS-Dyna. The results indicate that both viscosity and retarded damage are required for a realistic description of the material behaviour of concrete exposed to high strain effects [3].

  17. PREFACE: Neutrino physics at spallation neutron sources

    Science.gov (United States)

    Avignone, F. T.; Chatterjee, L.; Efremenko, Y. V.; Strayer, M.

    2003-11-01

    Unique because of their super-light masses and tiny interaction cross sections, neutrinos combine fundamental physics on the scale of the miniscule with macroscopic physics on the scale of the cosmos. Starting from the ignition of the primal p-p chain of stellar and solar fusion reactions that signal star-birth, these elementary leptons (neutrinos) are also critical players in the life-cycles and explosive deaths of massive stars and the production and disbursement of heavy elements. Stepping beyond their importance in solar, stellar and supernova astrophysics, neutrino interactions and properties influence the evolution, dynamics and symmetries of the cosmos as a whole. Further, they serve as valuable probes of its material content at various levels of structure from atoms and nuclei to valence and sea quarks. In the light of the multitude of physics phenomena that neutrinos influence, it is imperative to enhance our understanding of neutrino interactions and properties to the maximum. This is accentuated by the recent evidence of finite neutrino mass and flavour mixing between generations that reverberates on the plethora of physics that neutrinos influence. Laboratory experiments using intense neutrino fluxes would allow precision measurements and determination of important neutrino reaction rates. These can then complement atmospheric, solar and reactor experiments that have enriched so valuably our understanding of the neutrino and its repertoire of physics applications. In particular, intermediate energy neutrino experiments can provide critical information on stellar and solar astrophysical processes, along with advancing our knowledge of nuclear structure, sub-nuclear physics and fundamental symmetries. So where should we look for such intense neutrino sources? Spallation neutron facilities by their design are sources of intense neutrino pulses that are produced as a by-product of neutron spallation. These neutrino sources could serve as unique laboratories

  18. Benchmarking Geant4 for spallation neutron source calculations

    Science.gov (United States)

    DiJulio, Douglas D.; Batkov, Konstantin; Stenander, John; Cherkashyna, Nataliia; Bentley, Phillip M.

    2016-09-01

    Geant4 is becoming increasingly used for radiation transport simulations of spallation neutron sources and related components. Historically, the code has seen little usage in this field and it is of general interest to investigate the suitability of Geant4 for such applications. For this purpose, we carried out Geant4 calculations based on simple spallation source geometries and also with the the European Spallation Source Technical Design Report target and moderator configuration. The results are compared to calculations performed with the Monte Carlo N- Particle extended code. The comparisons are carried out over the full spallation neutron source energy spectrum, from sub-eV energies up to thousands of MeV. Our preliminary results reveal that there is generally good agreement between the simulations using both codes. Additionally, we have also implemented a general weight-window generator for Geant4 based applications and present some results of the method applied to the ESS target model.

  19. Proceedings of the international workshop on spallation materials technology

    Energy Technology Data Exchange (ETDEWEB)

    Mansur, L.K.; Ullmaier, H. [comps.

    1996-10-01

    This document contains papers which were presented at the International Workshop on Spallation Materials Technology. Topics included: overviews and thermal response; operational experience; materials experience; target station and component design; particle transport and damage calculations; neutron sources; and compatibility.

  20. Proceedings of the international workshop on spallation materials technology

    Energy Technology Data Exchange (ETDEWEB)

    Mansur, L.K.; Ullmaier, H. [comps.

    1996-10-01

    This document contains papers which were presented at the International Workshop on Spallation Materials Technology. Topics included: overviews and thermal response; operational experience; materials experience; target station and component design; particle transport and damage calculations; neutron sources; and compatibility.

  1. Spallation of Small Particles From Peristaltic Pump Tube Segments.

    Science.gov (United States)

    Liu, Yi; Faria, Monica; Leonard, Edward

    2017-07-01

    In most extracorporeal filtration devices such as hemodialysis a peristaltic pump is used to circulate blood. Pump function requires the repeated compression of an elastomeric tube from which particles may be shed into the circulatory system, a process called spallation. Earlier studies are likely to have missed the large number of small particles (particles down to 0.6 µm. As polyvinyl chloride (PVC) tubing is commonly used for this process, a series of studies was conducted on three different types to study its spallation characteristics, along with a co-extruded PVC/polyurethane tubing known for its enhanced biocompatibility properties. For all types of PVC tubes, the average size of the spallated particles was 0.83 ± 0.03 µm; for the PVC/polyurethane tubing the average size of the spallated particles was approximately twice that reported for PVC tubing. For PVC tubes with equal inner diameter, those with less plasticizer released fewer particles; for tubes with the same Shore hardness, tubes with larger internal diameters released fewer particles. It was also shown that PVC tubes operating at a slower flow rate does not reduce the total number of particles released per volume pumped. The total number of particles spallated from the PVC/polyurethane tubing was 10 times lower than from the lowest spallating PVC tubing. © 2017 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

  2. A High Intensity Linac for the National Spallation Neutron Source

    Science.gov (United States)

    Jason, A.; Bhatia, T.; Billen, J.; Schrage, D.; Kurennoy, S.; Krawczyk, F.; Lynch, M.; Nath, S.; Shafer, R.; Takeda, H.; Tallerico, P.; Wangler, T.; Wood, R.; Young, L.; Grand, P.; McKenzie-Wilson, R.

    1997-05-01

    The National Spallation Neutron Source to be constructed at Oak Ridge National Laboratory, requires a linac capable of delivering up to 5 MW of beam power to an accumulator ring with a nominal 6.2% duty factor and an energy of 1 GeV. Los Alamos, responsible for the linac design, has developed an appropriate room-temperature linac that consists of a drift-tube section from 2.5 to 20 MeV, a coupled-cavity drift-tube section to 100 MeV, and a coupled-cavity section to 1 GeV. The initial scenario requires an average 1.1-mA beam current with a corresponding 28 mA peak current and a 1.2-Mhz chopped time structure corresponding to the ring period. Upgrade to a 4.4 mA average current requires funneling with a peak current of 112 mA in the high-energy sections. Further parameters are presented along with beam dynamics and structure choices and mechanical and rf engineering considerations.

  3. Scattering effect in proton beam windows at spallation targets

    CERN Document Server

    Meng, C; Jing, H T

    2010-01-01

    Proton beam window (PBW) is a boundary wall between a high vacuum area in the proton beam line and the helium atmosphere in a helium vessel at a high beam power target. The thermal and mechanical problems of the PBW have been studied in other spallation neutron sources; however, the scattering effect in PBW is seldom reported in literature but it may pose serious problems for the target design if not well treated. This paper will report the simulation studies of the scattering effect in PBW. Different materials and different structures of PBW are discussed. Taking CSNS as an example, a thin single-layer aluminum alloy PBW with edge cooling has been chosen for CSNS-I and CSNS-II, and a sandwiched aluminum alloy PBW has been chosen for CSNS-III. Simulations results of the scattering effect in the presence of beam uniformization at target by using non-linear magnets at the different CSNS PBWs are presented. The simulations show that the scattering effect at PBW is very important in the beam loss and the beam dis...

  4. Deexcitation Modes in Spallation Nuclear Reactions

    Science.gov (United States)

    Velasco, F. G.; Guzmán, F.; Rodriguez, O.; Tumbarell, O.; Souza, D. A.; Samana, A. R.; Andrade-II, E.; Bernal Castillo, J. L.; Deppman, A.

    2016-08-01

    Spallation nuclear reactions in the range of 0.2 to 1.2 GeV are studied using the CRISP code. A new approach for the deexcitation stage of the compound nucleus was introduced. For the calculations of the level densities, this approach is based on the Back-shifted Fermi gas model (BSFG), which takes into account pairing effects and shell corrections, whereas the calculation of the fission barriers were performed by means of the Extended Thomas-Fermi plus Strutinsky Integral (ETFSI) method, which is a high-speed approximation to the Hartree-Fock method with pairing correlations treated as in the usual BCS plus blocking approach. This procedure is more appropriate to calculate level densities for exotic nuclei. Satisfactory results were obtained and compared with experimental data obtained in the GSI experiments. As another important result, we highlight some directions for the development of a qualitatively superior version of the CRISP code with the implementation of more realistic and suitable physical models to be applied in stable and exotic nuclei that participate in the process. This new version of the code includes several substantial changes in the decay of the hot compound nucleus which allow satisfactory agreement with the experimental data and a reduction of the adjustment parameters.

  5. The spallation neutron source: New opportunities

    Indian Academy of Sciences (India)

    Ian S Anderson

    2008-11-01

    The spallation neutron source (SNS) facility became operational in the spring of 2006, and is now well on its way to become the world-leading facility for neutron scattering. Furthermore, the SNS and the HFIR reactor facility, newly outfitted with a brilliant cold source and guide hall, were brought together within a single Neutron Sciences Directorate at ORNL providing the opportunity to develop science and instrumentation programs which take advantage of the unique characteristics of each source. SNS and HFIR will both operate as scientific user facilities. Access to these facilities is being managed under an integrated proposal system, which also includes the Center for Nanophase Materials Sciences (CNMS) and the electron microscopes in the Shared Research Equipment (SHARE) program. Presently, SNS has three instruments operating in the user program and seven more will begin operations in 2008. When complete, the facility will accommodate 25 instruments enabling researchers from the United States and abroad to study materials science that forms the basis for new technologies in telecommunications, manufacturing, transportation, information technology, biotechnology, and health.

  6. European Spallation Source and Neutron Science

    Science.gov (United States)

    Yeck, James

    2014-03-01

    International collaborations in large-scale scientific projects can link Sciences and Society. Following this goal, the European Spallation Source (ESS) is a multi-disciplinary research centre under design and construction in Lund, Sweden. This new facility is funded by a collaboration of 17 European countries. Scandinavia is providing 50 percent of the construction cost whilst the other member states are providing financial support mainly via in-kind contribution from institutes, laboratories or industries of the given countries. Scientists and engineers from 35 different countries are members of the workforce in Lund who participate in its design and construction. The ESS will enable new opportunities for researchers in fields of life sciences, energy, environmental technology, cultural heritage and fundamental physics by producing very high flux neutrons to study condensed matter physics, chemistry, biology, nuclear physics and materials science. The ESS will be up to 30 times brighter than today's leading facilities and neutron sources. A tungsten target and a 5 MW long pulse proton accelerator, composed mainly of superconducting Radio-Frequency components, are used to achieve these goals.

  7. Development of nuclear design criteria for neutron spallation sources

    Energy Technology Data Exchange (ETDEWEB)

    Sordo, F.; Abanades, A. [E.T.S. Industriales, Madrid Polytechnic University, UPM, J.Gutierrez Abascal, 2 -28006 Madrid (Spain)

    2008-07-01

    Spallation neutron sources allow obtaining high neutronic flux for many scientific and industrial applications. In recent years, several proposals have been made about its use, notably the European Spallation Source (ESS), the Japanese Spallation Source (JSNS) and the projects of Accelerator-Driven Subcritical reactors (ADS), particularly in the framework of EURATOM programs. Given their interest, it seems necessary to establish adequate design basis for guiding the engineering analysis and construction projects of this kind of installations. In this sense, all works done so far seek to obtain particular solutions to a particular design, but there has not been any general development to set up an engineering methodology in this field. In the integral design of a spallation source, all relevant physical processes that may influence its behaviour must be taken into account. Neutronic aspects (emitted neutrons and their spectrum, generation performance..), thermomechanical (energy deposition, cooling conditions, stress distribution..), radiological (spallation waste activity, activation reactions and residual heat) and material properties alteration due to irradiation (atomic displacements and gas generation) must all be considered. After analysing in a systematic manner the different options available in scientific literature, the main objective of this thesis was established as making a significant contribution to determine the limiting factors of the main aspects of spallation sources, its application range and the criteria for choosing optimal materials. To achieve this goal, a series of general simulations have been completed, covering all the relevant physical processes in the neutronic and thermal-mechanical field. Finally, the obtained criteria have been applied to the particular case of the design of the spallation source of subcritical reactors PDX-ADS and XT-ADS. These two designs, developed under the European R and D Framework Program, represent nowadays

  8. Tagging Spallation Backgrounds with Showers in Water-Cherenkov Detectors

    CERN Document Server

    Li, Shirley Weishi

    2015-01-01

    Cosmic-ray muons and especially their secondaries break apart nuclei ("spallation") and produce fast neutrons and beta-decay isotopes, which are backgrounds for low-energy experiments. In Super-Kamiokande, these beta decays are the dominant background in 6--18 MeV, relevant for solar neutrinos and the diffuse supernova neutrino background. In a previous paper, we showed that these spallation isotopes are produced primarily in showers, instead of in isolation. This explains an empirical spatial correlation between a peak in the muon Cherenkov light profile and the spallation decay, which Super-Kamiokande used to develop a new spallation cut. However, the muon light profiles that Super-Kamiokande measured are grossly inconsistent with shower physics. We show how to resolve this discrepancy and how to reconstruct accurate profiles of muons and their showers from their Cherenkov light. We propose a new spallation cut based on these improved profiles and quantify its effects. Our results can significantly benefit ...

  9. Modeling of water radiolysis at spallation neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Daemen, L.L.; Kanner, G.S.; Lillard, R.S.; Butt, D.P.; Brun, T.O.; Sommer, W.F.

    1998-12-01

    In spallation neutron sources neutrons are produced when a beam of high-energy particles (e.g., 1 GeV protons) collides with a (water-cooled) heavy metal target such as tungsten. The resulting spallation reactions produce a complex radiation environment (which differs from typical conditions at fission and fusion reactors) leading to the radiolysis of water molecules. Most water radiolysis products are short-lived but extremely reactive. When formed in the vicinity of the target surface they can react with metal atoms, thereby contributing to target corrosion. The authors will describe the results of calculations and experiments performed at Los Alamos to determine the impact on target corrosion of water radiolysis in the spallation radiation environment. The computational methodology relies on the use of the Los Alamos radiation transport code, LAHET, to determine the radiation environment, and the AEA code, FACSIMILE, to model reaction-diffusion processes.

  10. On the role of secondary pions in spallation targets

    Energy Technology Data Exchange (ETDEWEB)

    Mancusi, Davide [Paris-Saclay Univ., Gif-sur-Yvette (France). Den-Service d' Etude des Reacteurs et de Mathematiques Appliquees (SERMA); Lo Meo, Sergio [ENEA, Research Centre ' ' Ezio Clementel' ' , Bologna (Italy); INFN, Bologna (Italy); Colonna, Nicola [INFN, Bari (Italy); Boudard, Alain; David, Jean-Christophe; Leray, Sylvie [Paris-Saclay Univ., Gif-sur-Yvette (France). IRFU, CEA; Cortes-Giraldo, Miguel Antonio; Lerendegui-Marco, Jorge [Sevilla Univ. (Spain). Facultad de Fisica; Cugnon, Joseph [Liege Univ. (Belgium). AGO Dept.; Massimi, Cristian [INFN, Bologna (Italy); Bologna Univ. (Italy). Physics and Astronomy Dept.; Vlachoudis, Vasilis [European Organization for Nuclear Research (CERN), Geneva (Switzerland)

    2017-05-15

    We use particle-transport simulations to show that secondary pions play a crucial role for the development of the hadronic cascade and therefore for the production of neutrons and photons from thick spallation targets. In particular, for the nTOF lead spallation target, irradiated with 20 GeV/c protons, neutral pions are involved in the production of ∝ 90% of the high-energy photons; charged pions participate in ∝ 40% of the integral neutron yield. Nevertheless, photon and neutron yields are shown to be relatively insensitive to large changes of the average pion multiplicity in the individual spallation reactions. We characterize this robustness as a peculiar property of hadronic cascades in thick targets. (orig.)

  11. Characterization of the radiation background at the Spallation Neutron Source

    Science.gov (United States)

    DiJulio, Douglas D.; Cherkashyna, Nataliia; Scherzinger, Julius; Khaplanov, Anton; Pfeiffer, Dorothea; Cooper-Jensen, Carsten P.; Fissum, Kevin G.; Kanaki, Kalliopi; Kirstein, Oliver; Ehlers, Georg; Gallmeier, Franz X.; Hornbach, Donald E.; Iverson, Erik B.; Newby, Robert J.; Hall-Wilton, Richard J.; Bentley, Phillip M.

    2016-09-01

    We present a survey of the radiation background at the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory, TN, USA during routine daily operation. A broad range of detectors was used to characterize primarily the neutron and photon fields throughout the facility. These include a WENDI-2 extended range dosimeter, a thermoscientific NRD, an Arktis 4He detector, and a standard NaI photon detector. The information gathered from the detectors was used to map out the neutron dose rates throughout the facility and also the neutron dose rate and flux profiles of several different beamlines. The survey provides detailed information useful for developing future shielding concepts at spallation neutron sources, such as the European Spallation Source (ESS), currently under construction in Lund, Sweden.

  12. Spallative ablation of dielectrics by X-ray laser

    CERN Document Server

    Inogamov, N A; Faenov, A Ya; Khokhlov, V A; Shepelev, V V; Skobelev, I Yu; Kato, Y; Tanaka, M; Pikuz, T A; Kishimoto, M; Ishino, M; Nishikino, M; Fukuda, Y; Bulanov, S V; Kawachi, T; Petrov, Yu V; Anisimov, S I; Fortov, V E

    2009-01-01

    Short laser pulse in wide range of wavelengths, from infrared to X-ray, disturbs electron-ion equilibrium and rises pressure in a heated layer. The case where pulse duration $\\tau_L$ is shorter than acoustic relaxation time $t_s$ is considered in the paper. It is shown that this short pulse may cause thermomechanical phenomena such as spallative ablation regardless to wavelength. While the physics of electron-ion relaxation on wavelength and various electron spectra of substances: there are spectra with an energy gap in semiconductors and dielectrics opposed to gapless continuous spectra in metals. The paper describes entire sequence of thermomechanical processes from expansion, nucleation, foaming, and nanostructuring to spallation with particular attention to spallation by X-ray pulse.

  13. On the role of secondary pions in spallation targets

    CERN Document Server

    Mancusi, Davide; Colonna, Nicola; Boudard, Alain; Cortés-Giraldo, Miguel Antonio; Cugnon, Joseph; David, Jean-Christophe; Leray, Sylvie; Lerendegui-Marco, Jorge; Massimi, Cristian; Vlachoudis, Vasilis

    2016-01-01

    We use particle-transport simulations to show that secondary pions play a crucial role for the development of the hadronic cascade and therefore for the production of neutrons and photons from thick spallation targets. In particular, for the n_TOF lead spallation target, irradiated with 20-GeV/c protons, neutral pions are involved in the production of ~90% of the high-energy photons; charged pions participate in ~40% of the integral neutron yield. Nevertheless, photon and neutron yields are shown to be relatively insensitive to large changes of the average pion multiplicity in the individual spallation reactions. We characterize this robustness as a peculiar property of hadronic cascades in thick targets.

  14. Status of the AGS experiment for mercury spallation target development

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, Yujiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2000-03-01

    An experimental endeavor for exploitation of a MW class spallation target has been conducted using the AGS accelerator at BN on the neutron production along with the shock wave characteristics in the target, which are induced by a high intensity proton incident. This paper reviews the experiments, which has been carried out since 1997 in an international collaborative framework, namely the ASTE (AGS Spallation Target Experiment) collaboration with an emphasis on neutronics measurement, and gives the current status of the results provided through the experiment. (author)

  15. Neutron scattering instruments for the Spallation Neutron Source (SNS)

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, R.K.; Fornek, T. [Argonne National Lab., IL (United States); Herwig, K.W. [Oak Ridge National Lab., TN (United States)

    1998-07-01

    The Spallation Neutron Source (SNS) is a 1 MW pulsed spallation source for neutron scattering planned for construction at Oak Ridge National Laboratory. This facility is being designed as a 5-laboratory collaboration project. This paper addresses the proposed facility layout, the process for selection and construction of neutron scattering instruments at the SNS, the initial planning done on the basis of a reference set of ten instruments, and the plans for research and development (R and D) to support construction of the first ten instruments and to establish the infrastructure to support later development and construction of additional instruments.

  16. 5 MW pulsed spallation neutron source, Preconceptual design study

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    This report describes a self-consistent base line design for a 5 MW Pulsed Spallation Neutron Source (PSNS). It is intended to establish feasibility of design and as a basis for further expanded and detailed studies. It may also serve as a basis for establishing project cost (30% accuracy) in order to intercompare competing designs for a PSNS not only on the basis of technical feasibility and technical merit but also on the basis of projected total cost. The accelerator design considered here is based on the objective of a pulsed neutron source obtained by means of a pulsed proton beam with average beam power of 5 MW, in {approx} 1 {mu}sec pulses, operating at a repetition rate of 60 Hz. Two target stations are incorporated in the basic facility: one for operation at 10 Hz for long-wavelength instruments, and one operating at 50 Hz for instruments utilizing thermal neutrons. The design approach for the proton accelerator is to use a low energy linear accelerator (at 0.6 GeV), operating at 60 Hz, in tandem with two fast cycling booster synchrotrons (at 3.6 GeV), operating at 30 Hz. It is assumed here that considerations of cost and overall system reliability may favor the present design approach over the alternative approach pursued elsewhere, whereby use is made of a high energy linear accelerator in conjunction with a dc accumulation ring. With the knowledge that this alternative design is under active development, it was deliberately decided to favor here the low energy linac-fast cycling booster approach. Clearly, the present design, as developed here, must be carried to the full conceptual design stage in order to facilitate a meaningful technology and cost comparison with alternative designs.

  17. MEGAPIE, a 1 MW pilot experiment for a liquid metal spallation target

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, G.S. [Paul Scherrer Institut, Spallation Neutron Source Division, Villigen-PSI (Switzerland); Salvatores, M. [CEA Cadarache, Direction des Reacteurs Nucleaires, Saint-Paul-lez-Durance Cedex (France); Heusener, G. [Forschungszentrum Karlsruhe, Projekt Nukleare Sicherheitsforschung, Karlsruhe (Germany)

    2001-03-01

    MEGAPIE (Megawatt Pilot Target Experiment) is an initiative launched by Commissariat a l'Energie Atomique, Cadarache (France) and Forschungszentrum Karlsruhe (Germany) in collaboration with Paul Scherrer Institut (Switzerland), to demonstrate, in an international collaboration, the feasibility of a liquid lead bismuth target for spallation facilities at a beam power level of 1 MW. Such a target is under consideration for various concepts of accelerator driven systems (ADS) to be used in transmutation of nuclear waste and other applications world-wide. It also has the potential of increasing significantly the thermal neutron flux available at the spallation neutron source (SINQ) for neutron scattering. SINQ's beam power being close to 1 MW already, this facility offers a unique opportunity to realize such an experiment with a reasonably small number of new ancillary systems. The paper describes the basic features of the experiment and its boundary conditions, the technical concept of the target and underlying research carried out at participating laboratories. (author)

  18. Waste heat recovery from the European Spallation Source cryogenic helium plants - implications for system design

    Science.gov (United States)

    Jurns, John M.; Bäck, Harald; Gierow, Martin

    2014-01-01

    The European Spallation Source (ESS) neutron spallation project currently being designed will be built outside of Lund, Sweden. The ESS design includes three helium cryoplants, providing cryogenic cooling for the proton accelerator superconducting cavities, the target neutron source, and for the ESS instrument suite. In total, the cryoplants consume approximately 7 MW of electrical power, and will produce approximately 36 kW of refrigeration at temperatures ranging from 2-16 K. Most of the power consumed by the cryoplants ends up as waste heat, which must be rejected. One hallmark of the ESS design is the goal to recycle waste heat from ESS to the city of Lund district heating system. The design of the cooling system must optimize the delivery of waste heat from ESS to the district heating system and also assure the efficient operation of ESS systems. This report outlines the cooling scheme for the ESS cryoplants, and examines the effect of the cooling system design on cryoplant design, availability and operation.

  19. Spallation reactions. A successful interplay between modeling and applications

    CERN Document Server

    David, J -C

    2015-01-01

    The spallation reactions are a type of nuclear reaction which occur in space by interaction of the cosmic rays with interstellar bodies. The first spallation reactions induced with an accelerator took place in 1947 at the Berkeley cyclotron (University of California) with 200 MeV deuterons and 400 MeV alpha beams. They highlighted the multiple emission of neutrons and charged particles and the production of a large number of residual nuclei far different from the target nuclei. The same year R. Serber describes the reaction in two steps: a first and fast one with high-energy particle emission leading to an excited remnant nucleus, and a second one, much slower, the de-excitation of the remnant. In 2010 IAEA organized a worskhop to present the results of the most widely used spallation codes within a benchmark of spallation models. If one of the goals was to understand the deficiencies, if any, in each code, one remarkable outcome points out the overall high-quality level of some models and so the great improv...

  20. Transuranics Transmutation Using Neutrons Spectrum from Spallation Reactions

    Directory of Open Access Journals (Sweden)

    Maurício Gilberti

    2015-01-01

    Full Text Available The aim is to analyse the neutron spectrum influence in a hybrid system ADS-fission inducing transuranics (TRUs transmutation. A simple model consisting of an Accelerator-Driven Subcritical (ADS system containing spallation target, moderator or coolant, and spheres of actinides, “fuel,” at different locations in the system was modelled. The simulation was performed using the MCNPX 2.6.0 particles transport code evaluating capture (n,γ and fission (n,f reactions, as well as the burnup of actinides. The goal is to examine the behaviour and influences of the hard neutron spectrum from spallation reactions in the transmutation, without the contribution or interference of multiplier subcritical medium, and compare the results with those obtained from the neutron fission spectrum. The results show that the transmutation efficiency is independent of the spallation target material used, and the neutrons spectrum from spallation does not contribute to increased rates of actinides transmutation even in the vicinity of the target.

  1. Study on induced radioactivity of China Spallation Neutron Source

    Institute of Scientific and Technical Information of China (English)

    吴青彪; 王庆斌; 吴靖民; 马忠剑

    2011-01-01

    China Spallation Neutron Source (CSNS) is the first High Energy Intense Proton Accelerator planned to be constructed in China during the State Eleventh Five-Year Plan period, whose induced radioactivity is very important for occupational disease hazard as

  2. Opportunities for Neutrino Physics at the Spallation Neutron Source (SNS)

    CERN Document Server

    Efremenko, Yu

    2008-01-01

    In this paper we discuss opportunities for a neutrino program at the Spallation Neutrons Source (SNS) being commissioning at ORNL. Possible investigations can include study of neutrino-nuclear cross sections in the energy rage important for supernova dynamics and neutrino nucleosynthesis, search for neutrino-nucleus coherent scattering, and various tests of the standard model of electro-weak interactions.

  3. Thermal-Hydraulic Analysis of PDS-XADS Spallation Target%PDS-XADS散裂靶热工水力分析

    Institute of Scientific and Technical Information of China (English)

    艾尼塞; 俞冀阳; 杨永伟

    2013-01-01

    本文对小型加速器驱动的次临界系统(ADS)-PDS-XADS散裂靶进行了热工水力分析.分析的XADS型实验堆基于欧洲PDS-XADS实验项目的设计,使用铅铋合金(LBE)作为冷却剂.散裂靶是ADS的核心部件之一,用以确保反应堆功率维持在指定水平.本文利用计算流体力学软件ANSYSCFX 11.0对散裂靶的下部区域进行热工水力分析.分析采用稳态计算、剪切应力输运(SST)湍流模型,在壁面边界条件处采用自动壁面函数法,针对不同的散裂靶设计进行计算流体力学(CFD)分析,最后根据散裂靶设计限值选择最优设计方案.%The thermal-hydraulic analysis of PDS-XADS spallation target for 80 MW reactor core power was studied. PDS-XADS is a small scale experimental accelerator driven sub-critical system (ADS). The analysis presented in this paper was based on lead bismuth eutectic (LBE) cooled XADS type experimental reactors, which are the designs of the European experimental PDS-XADS project. The spallation target is a very important component of ADS because it is responsible to keep the reactor power at the required level by spallation reactions. A high rate of neutron production by spallation reaction creates the problem of decay heat cooling. LBE flow is properly cooled, but the window is not properly cooled because of the stagnation point in the pole of the window. It would be very difficult to keep the window temperature below the design limit, which is an important design limit challenge. Thermal-hydraulic analysis of LBE spallation target was carried out by using ANSYS CFX 11.0. The detailed CFD analysis, which reveals thermal and hydraulic conditions in the window and spallation region, was carried out for different spallation target designs. Finally, the spallation target design limit was used to choose the best design.

  4. A spallation-based irradiation test facility for fusion and future fission materials

    CERN Document Server

    Samec, K; Kadi, Y; Luis, R; Romanets, Y; Behzad, M; Aleksan, R; Bousson, S

    2014-01-01

    The EU’s FP7 TIARA program for developing accelerator-based facilities has recently demonstrated the unique capabilities of a compact and powerful spallation source for irradiating advanced nuclear materials. The spectrum and intensity of the neutron flux produced in the proposed facility fulfils the requirements of the DEMO fusion reactor for ITER, ADS reactors and also Gen III / IV reactors. Test conditions can be modulated, covering temperature from 400 to 550°C, liquid metal corrosion, cyclical or static stress up to 500 MPa and neutron/proton irradiation damage of up to 25 DPA per annum. The entire “TMIF” facility fits inside a cube 2 metres on a side, and is dimensioned for an accelerator beam power of 100 kW, thus reducing costs and offering great versatility and flexibility.

  5. Optimized concept design of the target station of Chinese spallation neutron source

    Science.gov (United States)

    Yan, Q. W.; Yin, W.; Yu, B. L.

    2005-08-01

    CSNS (Chinese spallation neutron source) target station, with proton beam power of 100 kW, consists of Tungsten rectangular target surrounded by a beryllium/steel reflector, three wing-moderators and the shield having 18 beam tubes. The leakage neutron intensity from the target (with reflector) and heat deposition on the target, reflector and shield were calculated using Monte Carlo code NMTC/JAM respectively. It is reported that the target having rectangular section will produce more leakage neutron intensity than a square one for the same proton power. The temperature and thermal stress distribution in the target disks were calculated by the finite element method. The performances of moderators were calculated using MCNP-4A code.

  6. Computer simulations for rf design of a Spallation Neutron Source external antenna H ion source

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sung-Woo [ORNL; Goulding, Richard Howell [ORNL; Kang, Yoon W [ORNL; Shin, Ki [ORNL; Welton, Robert F [ORNL

    2010-01-01

    Electromagnetic modeling of the multicusp external antenna H ion source for the Spallation Neutron Source SNS has been performed in order to optimize high-power performance. During development of the SNS external antenna ion source, antenna failures due to high voltage and multicusp magnet holder rf heating concerns under stressful operating conditions led to rf characteristics analysis. In rf simulations, the plasma was modeled as an equivalent lossy metal by defining conductivity as . Insulation designs along with material selections such as ferrite and Teflon could be included in the computer simulations to compare antenna gap potentials, surface power dissipations, and input impedance at the operating frequencies, 2 and 13.56 MHz. Further modeling and design improvements are outlined in the conclusion.

  7. Spallation Neutron Source Drift Tube Linac Resonance Control Cooling System Modeling

    CERN Document Server

    Tang, Johnny Y; Champion, Marianne M; Feschenko, Alexander; Gibson, Paul; Kiselev, Yuri; Kovalishin, A S; Kravchuk, Leonid V; Kvasha, Adolf; Schubert, James P

    2005-01-01

    The Resonance Control Cooling System (RCCS) for the warm linac of the Spallation Neutron Source was designed by Los Alamos National Laboratory. The primary design focus was on water cooling of individual component contributions. The sizing the RCCS water skid was accomplished by means of a specially created SINDA/FLUINT model tailored to these system requirements. A new model was developed in Matlab Simulink and incorporates actual operational values and control valve interactions. Included is the dependence of RF input power on system operation, cavity detuning values during transients, time delays that result from water flows through the heat exchanger, the dynamic process of water warm-up in the cooling system due to dissipated RF power on the cavity surface, differing contributions on the cavity detuning due to drift tube and wall heating, and a dynamic model of the heat exchanger with characteristics in close agreement to the real unit. Because of the Matlab Simulink model, investigation of a wide range ...

  8. Thermal-hydraulic simulation of mercury target concepts for a pulsed spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Siman-Tov, M.; Wendel, M.; Haines, J. [Oak Ridge National Lab., TN (United States)

    1996-06-01

    The Oak Ridge Spallation Neutron Source (ORSNS) is a high-power, accelerator-based pulsed spallation neutron source being designed by a multi-laboratory team led by Oak Ridge National Laboratory to achieve very high fluxes of neutrons for scientific experiments. The ORSNS is projected to have a 1 MW proton beam upgradable to 5 MW. About 60% of the beam power (1-5 MW, 17-83 kJ/pulse in 0.5 microsec at 60 cps) is deposited in the liquid metal (mercury) target having the dimensions of 65x30x10 cm (about 19.5 liter). Peak steady state power density is about 150 and 785 MW/m{sup 3} for 1 MW and 5 MW beam respectively, whereas peak pulsed power density is as high as 5.2 and 26.1 GW/m{sup 3}, respectively. The peak pulse temperature rise rate is 14 million C/s (for 5 MW beam) whereas the total pulse temperature rise is only 7 C. In addition to thermal shock and materials compatibility, key feasibility issues for the target are related to its thermal-hydraulic performance. This includes proper flow distribution, flow reversals, possible {open_quotes}hot spots{close_quotes} and the challenge of mitigating the effects of thermal shock through possible injection of helium bubbles throughout the mercury volume or other concepts. The general computational fluid dynamics (CFD) code CFDS-FLOW3D was used to simulate the thermal and flow distribution in three preliminary concepts of the mercury target. Very initial CFD simulation of He bubbles injection demonstrates some potential for simulating behavior of He bubbles in flowing mercury. Much study and development will be required to be able to `predict`, even in a crude way, such a complex phenomena. Future direction in both design and R&D is outlined.

  9. Dissertation: Precompound Emission of Energetic Light Fragments in Spallation Reactions

    Energy Technology Data Exchange (ETDEWEB)

    Kerby, Leslie Marie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-08-04

    Emission of light fragments (LF) from nuclear reactions is an open question. Different reaction mechanisms contribute to their production; the relative roles of each, and how they change with incident energy, mass number of the target, and the type and emission energy of the fragments is not completely understood. None of the available models are able to accurately predict emission of LF from arbitrary reactions. However, the ability to describe production of LF (especially at energies ≳ 30 MeV) from many reactions is important for different applications, such as cosmic-ray-induced Single Event Upsets (SEUs), radiation protection, and cancer therapy with proton and heavy-ion beams, to name just a few. The Cascade-Exciton Model (CEM) version 03.03 and the Los Alamos version of the Quark-Gluon String Model (LAQGSM) version 03.03 event generators in Monte Carlo N-Particle Transport Code version 6 (MCNP6) describe quite well the spectra of fragments with sizes up to ⁴He across a broad range of target masses and incident energies (up to ~ 5 GeV for CEM and up to ~ 1 TeV/A for LAQGSM). However, they do not predict the high energy tails of LF spectra heavier than ⁴He well. Most LF with energies above several tens of MeV are emitted during the precompound stage of a reaction. The current versions of the CEM and LAQGSM event generators do not account for precompound emission of LF larger than ⁴He. The aim of our work is to extend the precompound model in them to include such processes, leading to an increase of predictive power of LF-production in MCNP6. This entails upgrading the Modified Exciton Model currently used at the preequilibrium stage in CEM and LAQGSM. It also includes expansion and examination of the coalescence and Fermi break-up models used in the precompound stages of spallation reactions within CEM and LAQGSM. Extending our models to include emission of fragments heavier than ⁴He at the precompound stage has indeed provided results that have much

  10. Overcoming High Energy Backgrounds at Pulsed Spallation Sources

    CERN Document Server

    Cherkashyna, Nataliia; DiJulio, Douglas D.; Khaplanov, Anton; Pfeiffer, Dorothea; Scherzinger, Julius; Cooper-Jensen, Carsten P.; Fissum, Kevin G.; Ansell, Stuart; Iverson, Erik B.; Ehlers, Georg; Gallmeier, Franz X.; Panzner, Tobias; Rantsiou, Emmanouela; Kanaki, Kalliopi; Filges, Uwe; Kittelmann, Thomas; Extegarai, Maddi; Santoro, Valentina; Kirstein, Oliver; Bentley, Phillip M.

    2015-01-01

    Instrument backgrounds at neutron scattering facilities directly affect the quality and the efficiency of the scientific measurements that users perform. Part of the background at pulsed spallation neutron sources is caused by, and time-correlated with, the emission of high energy particles when the proton beam strikes the spallation target. This prompt pulse ultimately produces a signal, which can be highly problematic for a subset of instruments and measurements due to the time-correlated properties, and different to that from reactor sources. Measurements of this background have been made at both SNS (ORNL, Oak Ridge, TN, USA) and SINQ (PSI, Villigen, Switzerland). The background levels were generally found to be low compared to natural background. However, very low intensities of high-energy particles have been found to be detrimental to instrument performance in some conditions. Given that instrument performance is typically characterised by S/N, improvements in backgrounds can both improve instrument pe...

  11. A non-equilibrium microscopic description of spallation

    CERN Document Server

    Napolitani, P

    2016-01-01

    We investigate the prompt emission of few intermediate-mass fragments in spallation reactions induced by protons and deuterons in the 1 GeV range. Such emission has a minor contribution to the total reaction cross section, but it may overcome evaporation and fission channels in the formation of light nuclides. The role of mean-field dynamics and phase-space fluctuations in these reactions is investigated through the Boltzmann-Langevin transport equation. We found that a process of frustrated fragmentation and re-aggregation is a prominent mechanism of production of IMFs which can not be assimilated to the statistical decay of a compound nucleus. Very interestingly, this process may yield a small number of IMF in the exit channel, which may even reduce to two, and be wrongly confused with ordinary asymmetric fission. This interpretation, inspired by nuclear-spallation experiments, can be generalised to heavy-ion collisions approaching the fragmentation threshold.

  12. Monte Carlo simulation of NSE at reactor and spallation sources

    Energy Technology Data Exchange (ETDEWEB)

    Zsigmond, G.; Wechsler, D.; Mezei, F. [Hahn-Meitner-Institut Berlin, Berlin (Germany)

    2001-03-01

    A MC (Monte Carlo) computation study of NSE (Neutron Spin Echo) has been performed by means of VITESS investigating the classic and TOF-NSE options at spallation sources. The use of white beams in TOF-NSE makes the flipper efficiency in function of the neutron wavelength an important issue. The emphasis was put on exact evaluation of flipper efficiencies for wide wavelength-band instruments. (author)

  13. Spallation and fracture resulting from reflected and intersecting stress waves.

    Science.gov (United States)

    Kinslow, R.

    1973-01-01

    Discussion of the effects of stress waves produced in solid by explosions or high-velocity impacts. These waves rebound from free surfaces in the form of tensile waves that are capable of causing internal fractures or spallation of the material. The high-speed framing camera is shown to be an important tool for observing the stress waves and fracture in transparent targets, and its photographs provide valuable information on the mechanics of fracture.

  14. Irradiation facilities at the spallation neutron source SINQ

    Energy Technology Data Exchange (ETDEWEB)

    Lehmann, E.; Ledermann, J.; Aebersold, H.; Kuehne, G.; Kohlik, K. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-09-01

    Four independent experiments for sample irradiation are under construction and in preparation for operational tests at the spallation source SINQ. Three of them are located inside a thermal beam port with end positions inside or near the moderator tank. The other experiment will be established at the end position of a super mirror lined neutron guide for applications with cold neutrons. (author) 3 figs., 1 tab., 6 refs.

  15. Spallation neutron source and other high intensity froton sources

    Energy Technology Data Exchange (ETDEWEB)

    Weiren Chou

    2003-02-06

    This lecture is an introduction to the design of a spallation neutron source and other high intensity proton sources. It discusses two different approaches: linac-based and synchrotron-based. The requirements and design concepts of each approach are presented. The advantages and disadvantages are compared. A brief review of existing machines and those under construction and proposed is also given. An R&D program is included in an appendix.

  16. The BLAIRR Irradiation Facility Hybrid Spallation Target Optimization

    Energy Technology Data Exchange (ETDEWEB)

    Simos N.; Hanson A.; Brown, D.; Elbakhshawn, M.

    2016-04-11

    BLAIRR STUDY STATUS OVERVIEW Beamline Complex Evaluation/Assessment and Adaptation to the Goals Facility Radiological Constraints ? Large scale analyses of conventional facility and integrated shield (concrete, soil)Target Optimization and Design: Beam-target interaction optimization Hadronic interaction and energy deposition limitations Single phase and Hybrid target concepts Irradiation Damage Thermo-mechanical considerations Spallation neutron fluence optimization for (a) fast neutron irradiation damage (b) moderator/reflector studies, (c) NTOF potential and optimization (d) mono-energetic neutron beam

  17. Astrophysical Li-7 as a product of big bang nucleosynthesis and galactic cosmic-ray spallation

    Science.gov (United States)

    Olive, Keith A.; Schramm, David N.

    1992-01-01

    The astrophysical Li-7 abundance is considered to be largely primordial, while the Be and B abundances are thought to be due to galactic cosmic ray (GCR) spallation reactions on top of a much smaller big bang component. But GCR spallation should also produce Li-7. As a consistency check on the combination of big bang nucleosynthesis and GCR spallation, the Be and B data from a sample of hot population II stars is used to subtract from the measured Li-7 abundance an estimate of the amount generated by GCR spallation for each star in the sample, and then to add to this baseline an estimate of the metallicity-dependent augmentation of Li-7 due to spallation. The singly reduced primordial Li-7 abundance is still consistent with big bang nucleosynthesis, and a single GCR spallation model can fit the Be, B, and corrected Li-7 abundances for all the stars in the sample.

  18. Spallation Process of Thermally Grown Oxides by In-Situ CCD Monitoring Technique

    Institute of Scientific and Technical Information of China (English)

    QI Yu-hong; Philippe Lours; Yannick Le Maoult

    2009-01-01

    In cooling process of Fe-Cr-AI alloy oxidized at 1 300 ℃, the effect of cooling speed and exposure time on oxide spalled area fraction and successive variety of the spalled region were studied by investigating evolvement of the thermally grown oxide using in-situ CCD monitoring technique. The results showed that oxide spallation can be re-strained by controlling cooling speed and the critical temperature drop of spallation initiation which is closely related to the oxide thickness or exposure time, and the spallation process of a little region may be described in more detail as two routes:from the oxide/substrate interface micro-decohesion, micro-buckles, buckle spreading, buckle crack to spallation and from the interface micro-decohesion, micro-buckles, buckle crack and spallation to the residual oxide decohesion and spallation.

  19. Integral measurements of neutron production in spallation targets; Mesure integrale de la production de neutrons dans des cibles de spallation

    Energy Technology Data Exchange (ETDEWEB)

    Frehaut, J.; Deneuville, D.; Ledoux, X.; Lochard, J.P.; Longuet, J.L.; Petibon, E.; Alrick, K.; Bownan, D.; Cverna, F.; King, N.S.P.; Morgan, G.L. [Los Alamos National Lab., NM (United States); Greene, G.; Hanson, A.; Snead, L. [Brookhaven National Lab., Upton, NY (United States); Thompson, R. [Bechtel Nevada Corp., Las Vegas, NV (United States); Ward, T

    1998-12-31

    Measurements of neutron production for thick iron, tungsten and lead targets of different diameter prototypic for spallation systems have been made at SATURNE in an incident proton energy range from 400 MeV to 2 GeV. TIERCE code system calculations are in good agreement with experiment for iron and large diameter tungsten and lead targets. They overestimate the measured neutron production for tungsten and lead targets for diameter {<=}20 cm. (author) 10 refs.

  20. Energy dependence of isotopic spectra from spallation residues; Dependance en energie des spectres isotopiques de residus de spallation

    Energy Technology Data Exchange (ETDEWEB)

    Audouin, L

    2003-09-01

    Spallation reactions are collisions between heavy nuclei and light particle with an energy of a few hundreds MeV. The y are considered as a suitable way to create high- flux neutrons sources, which may used for example for the transmutation of nuclear wastes (hybrid reactors). The study of the residues from such reactions is both a way to understand the physics of the spallation and to provide information required for the design of industrial targets. The residues from the spallation of lead by proton at 500 MeV have been measured using the inverse kinematics technique in the FRS (fragments recoil separator). spectrometer from GSI (Barmstadt). This low energy required the use of new technique, for the experimental setup as well as during the analysis. The fragments were identified in-flight, prior to {beta} decay. Complete isotopic distributions are obtained with an accuracy ranging between 10 and 30%. Detailed information on the reaction kinematics are also obtained. Data are in excellent agreement with radio-chemical measurements, and bring new insights about the spallation process. The comparison with data measured on the same system with an incident energy of 1 GeV allows to discuss the influence of the projectile energy on the residues formation. It is concluded that the independence of the shape of the isobaric production cross sections regarding mass and energy of the projectile is preserved at low incident energies. The behaviour of Monte-Carlo codes is discussed with respect to those sets of data. The calculations show an improving agreement with decreasing energy, indicating that high-energy phenomena, for which some common assumptions become questionable, are the main reason for the observed discrepancies. (author)

  1. CLUSTER: concept study and design of a low-medium {beta} accelerating structure

    Energy Technology Data Exchange (ETDEWEB)

    Amaldi, U. [TERA Foundation, Via Puccini 11, 28100 (Italy); Citterio, A. [TERA Foundation, Via Puccini 11, 28100 (Italy); University of Milano Bicocca (Italy); Crescenti, M.; Giuliacci, A. [TERA Foundation, Via Puccini 11, 28100 (Italy); Tronci, C. [TERA Foundation, Via Puccini 11, 28100 (Italy); Imperial College, London (United Kingdom); Zennaro, R. [TERA Foundation, Via Puccini 11, 28100 (Italy)

    2007-10-15

    A novel linear accelerating structure is proposed particularly suited for hadrontherapy applications. The main features are compactness, due to the high frequency and consequent large gradients, and good power efficiency, especially at low beam velocities, obtained by using coupled H-mode cavities. The structure is called CLUSTER which stands for 'Coupled cavity Linac USing Transverse Electric Radial field'. In order to compare the performances of this structure with other hadrontherapy linac designs operating at high frequencies, a conceptual study has been performed by choosing the frequency of 3 GHz. Moreover a proof of principle of the radiofrequency behaviour of the cavity has been obtained by RF measurements on a prototype running at 1 GHz.

  2. Spallation sources in support of technology

    Energy Technology Data Exchange (ETDEWEB)

    Pynn, R. [Los Alamos National Lab., NM (United States)

    1996-05-01

    In this contribution I summarize a number of recent experiments at the Los Alamos Neutron Science Center (LANSCE) that have contributed to strategic and applied research. A number of new tools have been developed to address these problems, including software that allows materials texture to be obtained during Rietveld refinement, Bragg-edge diffraction, resonant-neutron and proton radiography. These tools have the potential to impact basic as well as applied research. It is clear that a new, more powerful neutron source such as the planned Japanese Hadron Project will be able to use these and other techniques to contribute in a direct way to important industrial technologies. (author)

  3. R&D-needs and opportunities to broaden the data base on materials and technology for liquid metal spallation targets

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, G.S.

    1996-06-01

    Liquid metals have so far only been used to a very limited extent as spallation targets, notably at the ISOLDE-facility at CERN (Pb and La) to produce radioactive isotopes. Virtually no systematic studies have been carried out so far. The available data base is by no means sufficient to answer conclusively very important questions such as predicting reliably the service time of medium-to-high power target systems or determining precisely what technological measures are required and appropriate to maintain an optimum coolant quality, to mitigate the effects of pressure waves in short pulse sources and others. During the workshop several areas have been identified, where there exists an urgent need for improved knowledge and reliable data, and opportunities have been presented to acquire such knowledge and to generate such data. Opportunities to do such research and pertinent know-how, although scarce, are spread over institutions in several countries, and efforts to use these opportunities often require substantial resources both in man power and money. The workshop participants therefore unanimously supported the view that a coordinated and internationally concerted effort should be undertaken to make the best possible use of existing opportunities and available resources in order to develop the knowledge and technology necessary for the deployment and safe operation of target systems suitable for pulsed spallation neutron sources in the multi-megawatt range of beam power.

  4. Coupled fluid/structure analyses of the MEGAPIE spallation source target during transients

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Brian L. [Thermal-Hydraulics Laboratory, Nuclear Energy and Safety Dept., Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Waihung Leung [Spallation Neutron Source Division, Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Alberto Zucchini [UTS Tecnologie Fisiche Avanzate, Sezione Metodologie e Diagnostiche, ENEA, Bologna (Italy)

    2005-07-01

    Full text of publication follows: In the ADS (Accelerator Driven System) concept, neutrons generated from spallation reactions are used to initiate and maintain a continuous chain reaction in a sub-critical nuclear core. In some ADS designs, the spallation neutrons are generated from the proton bombardment of liquid lead bismuth eutectic (LBE). In this arrangement, the LBE acts both as the target material and the means by which heat is removed from the spallation region. A pilot facility at the Paul Scherrer Institute in Switzerland, supported by an international partnership, aims to demonstrate the feasibility of the LBE target concept. Efforts are coordinated under the project title MEGAPIE, and groups from Belgium, France, Germany, Italy, Japan, South Korea, Switzerland and the USA are involved in the design, manufacture and safety assessment of the target. As a consequence of the spallation reactions, about 700 kW of heat is deposited in the target, and considerable effort is being expended to ensure continuing coolability and structural integrity under a variety of operational and abnormal conditions. It is not possible to fully verify the cooling principle by means of mock-up experiments, because of the difficulty in reproducing the volumetric heating at the appropriate power density (at maximum, 1 GW/m{sup 3} for a beam power of 1 MW). Consequently, heavy reliance is placed on detailed, numerical analyses. This requires the simultaneous application of a system-analysis capability, in our case RELAP5, a Computational Fluid Dynamics (CFD) tool, in our case CFX-4, and a structural analysis code (ABAQUS). The paper gives three examples of transient analyses carried out as part of the safety assessment of the target: (1) a beamline trip; (2) failure of the primary electro-magnetic pump (EMP); and (3) failure of the secondary EMP. Beamline trips are expected to occur frequently as a consequence of accelerator problems and/or beam instabilities during the

  5. Nondiffractive applications of neutrons at the spallation source SINQ

    Energy Technology Data Exchange (ETDEWEB)

    Lehmann, E. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1996-11-01

    The paper delivers an overview about experiments with neutrons from the spallation source SINQ which are not especially devoted to neutron scattering. A total of six experimental facilities are under construction using thermal as well as cold neutrons. Starting with some general considerations about the interaction of neutrons with matter, the principles, boundary conditions and the experimental set up of these experiments are described briefly. Some more details are given for the neutron radiography facility NEUTRA as the author`s special interest and research field. (author) 7 figs., 2 tabs., 9 refs.

  6. VESPA: The vibrational spectrometer for the European Spallation Source

    Science.gov (United States)

    Fedrigo, Anna; Colognesi, Daniele; Bertelsen, Mads; Hartl, Monika; Lefmann, Kim; Deen, Pascale P.; Strobl, Markus; Grazzi, Francesco; Zoppi, Marco

    2016-06-01

    VESPA, Vibrational Excitation Spectrometer with Pyrolytic-graphite Analysers, aims to probe molecular excitations via inelastic neutron scattering. It is a thermal high resolution inverted geometry time-of-flight instrument designed to maximise the use of the long pulse of the European Spallation Source. The wavelength frame multiplication technique was applied to provide simultaneously a broad dynamic range (about 0-500 meV) while a system of optical blind choppers allows to trade flux for energy resolution. Thanks to its high flux, VESPA will allow the investigation of dynamical and in situ experiments in physical chemistry. Here we describe the design parameters and the corresponding McStas simulations.

  7. Numerical modelling of spallation in 2D hydrodynamics codes

    Science.gov (United States)

    Maw, J. R.; Giles, A. R.

    1996-05-01

    A model for spallation based on the void growth model of Johnson has been implemented in 2D Lagrangian and Eulerian hydrocodes. The model has been extended to treat complete separation of material when voids coalesce and to describe the effects of elevated temperatures and melting. The capabilities of the model are illustrated by comparison with data from explosively generated spall experiments. Particular emphasis is placed on the prediction of multiple spall effects in weak, low melting point, materials such as lead. The correlation between the model predictions and observations on the strain rate dependence of spall strength is discussed.

  8. Multiple-Scale Geomechanical Models for Thermal Spallation Drilling.

    Science.gov (United States)

    Lomov, I.; Walsh, S. D.; Roberts, J. J.

    2011-12-01

    Widespread adoption of geothermal energy will require access to deeply buried geothermal sources in granitic basement rocks at high temperatures and pressures. Exploiting these resources necessitates novel methods for drilling, stimulation, and maintenance, under operating conditions difficult or impossible to test in laboratory settings. Physically rigorous numerical modeling tools are vital to highlight potential risks, guide process optimization and reduce the uncertainties involved in these developing technologies. In this presentation, we discuss a numerical modeling effort investigating the multiscale mechanics of thermal spallation drilling (TSD) - a technique in which rock is fragmented into small flakes by a high temperature fluid jet. This process encompasses interconnected phenomena on several length and time scales: from system-scale fluid dynamics to grain-scale thermomechanics of spallation. Here we describe how these disperate scales are simulated using GEODYN, a parallel Eulerian compressible solid and fluid dynamics code with adaptive mesh refinement (AMR) capabilities. GEODYN is able to simulate materials under extremely large deformations, resolve details of wave propagation within grains, and uses a continuum damage mechanics approach to represent fracture. We will present results from both system- and grain-scale simulations describing the transfer of heat from the high temperature jet to the rock face, and the effect of grain-scale properties such as incipient flaw distribution, grain size and grain size distribution, heat flux, applied temperature and material heterogeneity on the onset of spallation. Detailed computer modeling helps to address several of the uncertainties surrounding TSD: 1) What rock compositions are drillable with TSD? 2) How do grain size and grain size distribution affect TSD and drilling rates? 3) What combination of macroscopic (Poisson ratio, heat capacity and thermal conductivity) and microscopic (flaw distribution

  9. Microstructure and mechanical properties of railway wheels manufactured with low-medium carbon Si-Mn-Mo-V steel

    Institute of Scientific and Technical Information of China (English)

    Mingru Zhang; Haicheng Gu

    2008-01-01

    The suitability of carbide-free bainite steel as railway wheel materials was investigated. The low-medium carbon Si-Mn-Mo-V steel was designed to make railway wheels by forging and rolling. The slack quenching with water was conducted on the tread of rim section by programmed control to simulate isothermal heat treatment after being austenitized. Microstructures and mechanical properties have been studied. The results indicate that the microstructure of the rim is mainly carbide-free bainite, and the mixed mi- crostructure of bainitic ferrite and granular bainite is observed in web and hub. The mechanical properties are superior to both the standard requirements and the commercial production, such as CL60 plain carbon. The Charpy impact energy is relatively high at room and/or subzero temperatures. The force-displacement curves and fractographies reveal the excellent ability of resistance to crack initiation and propagation.

  10. Oak Ridge Spallation Neutron Source (ORSNS) target station design integration

    Energy Technology Data Exchange (ETDEWEB)

    McManamy, T.; Booth, R.; Cleaves, J.; Gabriel, T. [and others

    1996-06-01

    The conceptual design for a 1- to 3-MW short pulse spallation source with a liquid mercury target has been started recently. The design tools and methods being developed to define requirements, integrate the work, and provide early cost guidance will be presented with a summary of the current target station design status. The initial design point was selected with performance and cost estimate projections by a systems code. This code was developed recently using cost estimates from the Brookhaven Pulsed Spallation Neutron Source study and experience from the Advanced Neutron Source Project`s conceptual design. It will be updated and improved as the design develops. Performance was characterized by a simplified figure of merit based on a ratio of neutron production to costs. A work breakdown structure was developed, with simplified systems diagrams used to define interfaces and system responsibilities. A risk assessment method was used to identify potential problems, to identify required research and development (R&D), and to aid contingency development. Preliminary 3-D models of the target station are being used to develop remote maintenance concepts and to estimate costs.

  11. Generic guide concepts for the European Spallation Source

    CERN Document Server

    Zendler, C; Bentley, P M

    2015-01-01

    The construction of the European Spallation Source (ESS) faces many challenges from the neutron beam transport point of view: The spallation source is specified as being driven by a 5 MW beam of protons, each with 2 GeV energy, and yet the requirements in instrument background suppression relative to measured signal vary between 10$^{-6}$ and 10$^{-8}$. The energetic particles, particularly above 20 MeV, which are expected to be produced in abundance in the target, have to be filtered in order to make the beamlines safe, operational and provide good quality measurements with low background. We present generic neutron guides of short and medium length instruments which are optimized for good performance at minimal cost. Direct line of sight to the source is avoided twice, with either the first point out of line of sight or both being inside the bunker (20\\,m) to minimize shielding costs. These guide geometries are regarded as a baseline to define standards for instruments to be constructed at ESS. They are use...

  12. A Very Intense Neutrino Super Beam Experiment for Leptonic CP Violation Discovery based on the European Spallation Source Linac: A Snowmass 2013 White Paper

    CERN Document Server

    Baussan, E; Bogomilov, M.; Bouquerel, E.; Cederkäll, J.; Christiansen, P.; Coloma, P.; Cupial, P.; Danared, H.; Densham, C.; Dracos, M.; Ekelöf, T.; Eshraqi, M.; Fernandez Martinez, E.; Gaudiot, G.; Hall-Wilton, R.; Koutchouk, J.P.; Lindroos, M.; Matev, R.; McGinnis, D.; Mezzetto, M.; Miyamoto, R.; Mosca, L.; Ohlsson, T.; Öhman, H.; Osswald, F.; Peggs, S.; Poussot, P.; Ruber, R.; Tang, J.Y.; Tsenov, R.; Vankova-Kirilova, G.; Vassilopoulos, N.; Wildner, E.; Wurtz, J.

    2014-01-01

    Very intense neutrino beams and large neutrino detectors will be needed in order to enable the discovery of CP violation in the leptonic sector. We propose to use the proton linac of the European Spallation Source currently under construction in Lund, Sweden to deliver, in parallel with the spallation neutron production, a very intense, cost effective and high performance neutrino beam. The baseline program for the European Spallation Source linac is that it will be fully operational at 5 MW average power by 2022, producing 2 GeV 2.86 ms long proton pulses at a rate of 14 Hz. Our proposal is to upgrade the linac to 10 MW average power and 28 Hz, producing 14 pulses/s for neutron production and 14 pulses/s for neutrino production. Furthermore, because of the high current required in the pulsed neutrino horn, the length of the pulses used for neutrino production needs to be compressed to a few $\\mu$s with the aid of an accumulator ring. A long baseline experiment using this Super Beam and a megaton underground ...

  13. EXPERIMENTAL ANALYSES OF SPALLATION NEUTRONS GENERATED BY 100 MEV PROTONS AT THE KYOTO UNIVERSITY CRITICAL ASSEMBLY

    Directory of Open Access Journals (Sweden)

    CHEOL HO PYEON

    2013-02-01

    Full Text Available Neutron spectrum analyses of spallation neutrons are conducted in the accelerator-driven system (ADS facility at the Kyoto University Critical Assembly (KUCA. High-energy protons (100 MeV obtained from the fixed field alternating gradient accelerator are injected onto a tungsten target, whereby the spallation neutrons are generated. For neutronic characteristics of spallation neutrons, the reaction rates and the continuous energy distribution of spallation neutrons are measured by the foil activation method and by an organic liquid scintillator, respectively. Numerical calculations are executed by MCNPX with JENDL/HE-2007 and ENDF/B-VI libraries to evaluate the reaction rates of activation foils (bismuth and indium set at the target and the continuous energy distribution of spallation neutrons set in front of the target. For the reaction rates by the foil activation method, the C/E values between the experiments and the calculations are found around a relative difference of 10%, except for some reactions. For continuous energy distribution by the organic liquid scintillator, the spallation neutrons are observed up to 45 MeV. From these results, the neutron spectrum information on the spallation neutrons generated at the target are attained successfully in injecting 100 MeV protons onto the tungsten target.

  14. Spallation occurrence from polyamide materials irradiated by thermal plasma with water absorption

    Science.gov (United States)

    Nakano, Tomoyuki; Tanaka, Yasunori; Nakagawa, T.; Shinsei, N.; Uesugi, Y.; Ishijima, T.

    2016-09-01

    This paper first describes the effect of water absorption in polyamide material irradiated by thermal plasmas on the occurrence of spallation phenomena. The interaction between polyamide materials and arc plasmas occurs particularly in the low voltage circuit breaker and aerospace fields. Spallation phenomena are those in which polymer particles are ejected from polymer bulk materials irradiated by high heat flux. To confirm the effect of water absorption into the polyamide material on spallation phenomena, polyamide specimens with and without water absorption were irradiated by Ar inductively coupled thermal plasma. The results show that the polyamide specimen with water absorption ejected spallation particles, whereas the polyamide specimen without water absorption were only slightly ejected, indicating that water absorption promotes the occurrence of spallation. The cooling effects of the spallation polyamide 66 (PA66) particles ablation were also estimated in hot air to assess the arc quenching ability from the spallation particle inclusion. This estimation showed that 10 and more PA66 particles inclusion might decrease the air temperature by 3000 K effectively, which can be useful to enhance arc quenching in circuit breakers working in air.

  15. Prototype Spallation Neutron Source Rotating Target Assembly Final Test Report

    Energy Technology Data Exchange (ETDEWEB)

    McManamy, Thomas J [ORNL; Graves, Van [Oak Ridge National Laboratory (ORNL); Garmendia, Amaia Zarraoa [IDOM Bilbao; Sorda, Fernando [ESS Bilbao; Etxeita, Borja [IDOM Bilbao; Rennich, Mark J [ORNL

    2011-01-01

    A full-scale prototype of an extended vertical shaft, rotating target assembly based on a conceptual target design for a 1 to 3-MW spallation facility was built and tested. Key elements of the drive/coupling assembly implemented in the prototype include high integrity dynamic face seals, commercially available bearings, realistic manufacturing tolerances, effective monitoring and controls, and fail-safe shutdown features. A representative target disk suspended on a 3.5 meter prototypical shaft was coupled with the drive to complete the mechanical tests. Successful operation for 5400 hours confirmed the overall mechanical feasibility of the extended vertical shaft rotating target concept. The prototype system showed no indications of performance deterioration and the equipment did not require maintenance or relubrication.

  16. Evolution of a spallation reaction: experiment and Monte Carlo simulation

    CERN Document Server

    Enke, M; Hilscher, D; Jahnke, U; Schapiro, O; Letourneau, A; Galin, J; Goldenbaum, F; Lott, B; Peghaire, A; Filges, D; Neef, R D; Nünnighoff, K; Paul, N; Schaal, H; Sterzenbach, G; Tietze, A; Pienkowski, L

    1999-01-01

    Reaction cross sections and production cross sections for neutrons, hydrogen, and helium have been measured for 1.2, 1.8 GeV p+Fe, Ni, Ag, Ta, W, Au, Pb and U and are compared with different intra-nuclear-cascade- combined with evaporation-models. Agreement for neutrons and considerable differences for light charged particles are observed between experiment and calculation as well as between different models. The discrepancies are associated with specific deficiencies in the models. The exclusive data measured with two 4 pi-detectors for neutron and charged particle detection allowed furthermore a systematic comparison of observables characteristic of different stages of the temporal evolution of a spallation reaction: inelastic collision probability, excitation energy distribution, pre-equilibrium emission, and inclusive production cross sections.

  17. The NNbar Experiment at the European Spallation Source

    CERN Document Server

    Frost, M J

    2016-01-01

    The observation of neutron to antineutron oscillation would be the first experimental evidence to show that baryon number is not a conserved quantity. It also provides an answer to the hypothesized post-sphaleron baryogenesis mechanism shortly after the Big Bang. The free oscillation time {\\tau_{n\\rightarrow\\bar{n}} has a lower limit at 8.7 x 10^7 seconds determined at ILL in 1994. Current beyond Standard Model theories of this oscillation time estimate the value to be on the order of 10^{10} seconds. A new experiment is proposed at the European Spallation Source that has 1000 times the sensitivity of the previous experiment, and would confirm the viability of those beyond Standard Model theories.

  18. Sulfur and Moisture Effects on Alumina Scale and TBC Spallation

    Science.gov (United States)

    Smialek, James L.

    2007-01-01

    It has been well established that a few ppmw sulfur impurity may segregate to the interface of thermally grown alumina scales and the underlying substrate, resulting in bond degradation and premature spallation. This has been shown for NiAl and NiCrAl-based alloys, bare single crystal superalloys, or coated superalloys. The role of reactive elements (especially Y) has been to getter the sulfur in the bulk and preclude interfacial segregation. Pt additions are also very beneficial, however a similar thermodynamic explanation does not apply. The purpose of the present discussion is to highlight some observations of these effects on Rene'142, Rene'N5, PWA1480, and PWA1484. For PWA1480, we have mapped cyclic oxidation and spallation in terms of potential sulfur interfacial layers and found that a cumulative amount of about one monolayer is sufficient to degrade long term adhesion. Depending on substrate thickness, optimum performance occurs if sulfur is reduced below about 0.2-0.5 ppmw. This is accomplished in the laboratory by hydrogen annealing or commercially by melt-fluxing. Excellent 1150 C cyclic oxidation is thus demonstrated for desulfurized Rene'142, Rene'N5, and PWA1484. Alternatively, a series of N5 alloys provided by GE-AE have shown that as little as 15 ppmw of Y dopant was effective in providing remarkable scale adhesion. In support of a Y-S gettering mechanism, hydrogen annealing was unable to desulfurize these alloys from their initial level of 5 ppmw S. This impurity and critical doping level corresponds closely to YS or Y2S3 stoichiometry. In many cases, Y-doped alloys or alloys with marginal sulfur levels exhibit an oxidative sensitivity to the ambient humidity called Moisture-Induced Delayed Spallation (MIDS). After substantial scale growth, coupled with damage from repeated cycling, cold samples may spall after a period of time, breathing on them, or immersing them in water. While stress corrosion arguments may apply, we propose that the underlying

  19. Thermal shock analysis of liquid-mercury spallation target

    CERN Document Server

    Ishikura, S; Futakawa, M; Hino, R; Date, H

    2002-01-01

    The developments of the neutron scattering facilities are carried out under the high-intensity proton accelerator project promoted by JAERI and KEK. To estimate the structural integrity of the heavy liquid-metal (Hg) target used as a spallation neutron source in a MW-class neutron scattering facility, dynamic stress behavior due to the incident of a 1 MW-pulsed proton beam was analyzed by using FEM code. Two-type target containers with semi-cylindrical type and flat-plate type window were used as models for analyses. As a result, it is confirmed that the stress (pressure wave) generated by dynamic thermal shock becomes the largest at the center of window, and the flat-plate type window is more advantageous from the structural viewpoint than the semi-cylindrical type window. It has been understood that the stress generated in the window by the pressure wave can be treated as the secondary stress. (author)

  20. Characteristics of the WNR: a pulsed spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Russell, G.J.; Lisowski, P.W.; Howe, S.D.; King, N.S.P.; Meier, M.M.

    1982-01-01

    The Weapons Neutron Research facility (WNR) is a pulsed spallation neutron source in operation at the Los Alamos National Laboratory. The WNR uses part of the 800-MeV proton beam from the Clinton P. Anderson Meson Physics Facility accelerator. By choosing different target and moderator configurations and varying the proton pulse structure, the WNR can provide a white neutron source spanning the energy range from a few MeV to 800 MeV. The neutron spectrum from a bare target has been measured and is compared with predictions using an Intranuclear Cascade model coupled to a Monte Carlo transport code. Calculations and measurements of the neutronics of WNR target-moderator assemblies are presented.

  1. Fundamental neutron physics at a 1 MW long pulse spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Greene, G.L.

    1995-12-31

    Modern neutron sources and modern neutron science share a common origin in mid twentieth century scientific investigations concerned with the study of the fundamental interactions between elementary particles. Since the time of that common origin, neutron science and the study of elementary particles have evolved into quite disparate disciplines. The neutron became recognized as a powerful tool for the study of condensed matter with modern neutron sources being primarily used (and primarily justified) as tools for condensed matter research. The study of elementary particles has, of course, led to the development of rather different tools and is now dominated by activities carried out at extremely high energies. Notwithstanding this trend, the study of fundamental interactions using neutrons has continued and remains a vigorous activity at many contemporary neutron sources. This research, like neutron scattering research, has benefited enormously by the development of modern high flux neutron facilities. Future sources, particularly high power spallation sources, offer exciting possibilities for the continuation of this program of research.

  2. Mercury target R&D for the Oak Ridge spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Haines, J.R.; DiStefano, J.; Farrell, K.; Gabriel, T.A. [Oak Ridge National Lab., TN (United States)] [and others

    1996-06-01

    The conceptual design for the Oak Ridge Spallation Neutron Source (ORSNS) incorporates liquid mercury as its reference target material. A flowing liquid target was selected mainly because of the increased power handling capability possible with the convective transport process. The major reasons for choosing mercury as the liquid target material are because it: (1) is a liquid at room temperature, (2) has good heat transport properties, and (3) has a high atomic number and mass density resulting in high neutron yield and source brightness. Since liquid targets are not widely utilized in presently operating accelerator targets and because of the challenges posed by the intense, pulsed thermal energy deposition ({approximately}20-100 kJ deposited during each 1-10 {mu}s pulse), considerable R&D is planned for the mercury target concept. The key feasibility issue that will be addressed in early R&D efforts are the effects of the thermal shock environment, which will include development and testing of approaches to mitigate these effects. Materials compatiblity and ES&H issues associated with the use of liquid mercury are also of major importance in early R&D efforts. A brief description of the mercury target design concept, results of initial evaluations of its performance characteristics, identification of its critical issues, and an outline of the R&D program aimed at addressing these issues will be presented.

  3. RF H-minus ion source development in China spallation neutron source

    Science.gov (United States)

    Chen, W.; Ouyang, H.; Xiao, Y.; Liu, S.; Lü, Y.; Cao, X.; Huang, T.; Xue, K.

    2017-08-01

    China Spallation Neutron Source (CSNS) phase-I project currently uses a Penning surface plasma H- ion source, which has a life time of several weeks with occasional sparks between high voltage electrodes. To extend the life time of the ion source and prepare for the CSNS phase-II, we are trying to develop a RF negative hydrogen ion source with external antenna. The configuration of the source is similar to the DESY external antenna ion source and SNS ion source. However several changes are made to improve the stability and the life time. Firstly, Si3N4 ceramic with high thermal shock resistance, and high thermal conductivity is used for plasma chamber, which can endure an average power of 2000W. Secondly, the water-cooled antenna is brazed on the chamber to improve the energy efficiency. Thirdly, cesium is injected directly to the plasma chamber if necessary, to simplify the design of the converter and the extraction. Area of stainless steel exposed to plasma is minimized to reduce the sputtering and degassing. Instead Mo, Ta, and Pt coated materials are used to face the plasma, which makes the self-cleaning of the source possible.

  4. Stripper foil failure modes and cures at the Oak Ridge Spallation Neutron Source

    Directory of Open Access Journals (Sweden)

    M. A. Plum

    2011-03-01

    Full Text Available The Oak Ridge Spallation Neutron Source comprises a 1 GeV, 1.5 MW linear accelerator followed by an accumulator ring and a liquid mercury target. To manage the beam loss caused by the H^{0} excited states created during the H^{-} charge-exchange injection into the accumulator ring, the stripper foil is located inside one of the chicane dipoles. This has some interesting consequences that were not fully appreciated until the beam power reached about 840 kW. One consequence was sudden failure of the stripper foil system due to convoy electrons stripped from the incoming H^{-} beam, which circled around to strike the foil bracket and cause bracket failure. Another consequence is that convoy electrons can reflect back up from the electron catcher and strike the foil and bracket. An additional contributor to foil system failure is vacuum breakdown due to the charge developed on the foil by secondary electron emission. In this paper we detail these and other interesting failure mechanisms and describe the improvements we have made to mitigate them.

  5. Device for Writing the Time Tail from Spallation Neutron Pulses

    Energy Technology Data Exchange (ETDEWEB)

    Langan, P. (Paul); Schoenborn, Benno P.; Langan, P. (Paul); Schoenborn, Benno P.; Daemen, L. L. (Luc L.)

    2001-01-01

    Recent work at Los Alamos Neutron Science Center (LANSCE), has shown that there are large gains in neutron beam intensity to be made by using coupled moderators at spallation neutron sources. Most of these gains result from broadening the pulse-width in time. However the accompanying longer exponential tail at large emission times can be a problem in that it introduces relatively large beam-related backgrounds at high resolutions. We have designed a device that can reshape the moderated neutron beam by cutting the time-tail so that a sharp time resolution can be re-established without a significant loss in intensity. In this work the basic principles behind the tail-cutter and some initial results of Monte Carlo simulations are described. Unwanted neutrons in the long time-tail are diffracted out of the transmitted neutron beam by a nested stack of aperiodic multi-layers, rocking at the same frequency as the source. Nested aperiodic multi-layers have recently been used at X-ray sources and as band-pass filters in quasi-Laue neutron experiments at reactor neutron sources. Optical devices that rock in synchronization with a pulsed neutron beam are relatively new but are already under construction at LANSCE. The tail-cutter described here is a novel concept that uses existing multi-layer technology in a new way for spallation neutrons. Coupled moderators in combination with beam shaping devices offer the means of increasing flux whilst maintaining a sharp time distribution. A prototype device is being constructed for the protein crystallography station at LANSCE. The protein crystallography station incorporates a water moderator that has been judiciously coupled in order to increase the flux over neutron energies that are important to structural biology (3-80meV). This development in moderator design is particularly important because protein crystallography is flux limited and because conventional ambient water and cold hydrogen moderators do not provide relatively

  6. The cold neutron chopper spectrometer at the Spallation Neutron Source—A review of the first 8 years of operation

    Science.gov (United States)

    Ehlers, G.; Podlesnyak, A. A.; Kolesnikov, A. I.

    2016-09-01

    The first eight years of operation of the Cold Neutron Chopper Spectrometer (CNCS) at the Spallation Neutron Source in Oak Ridge is being reviewed. The instrument has been part of the facility user program since 2009, and more than 250 individual user experiments have been performed to date. CNCS is an extremely powerful and versatile instrument and offers leading edge performance in terms of beam intensity, energy resolution, and flexibility to trade one for another. Experiments are being routinely performed with the sample at extreme conditions: T ≲ 0.05 K, p ≳ 2 GPa, and B = 8 T can be achieved individually or in combination. In particular, CNCS is in a position to advance the state of the art with inelastic neutron scattering under pressure, and some of the recent accomplishments in this area will be presented in more detail.

  7. Proceedings of the workshop on ion source issues relevant to a pulsed spallation neutron source: Part 1: Workshop summary

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, L.; Leung, K.N.; Alonso, J. [eds.

    1994-10-01

    The workshop reviewed the ion-source requirements for high-power accelerator-driven spallation neutron facilities, and the performance of existing ion sources. Proposals for new facilities in the 1- to 5-MW range call for a widely differing set of ion-source requirements. For example, the source peak current requirements vary from 40 mA to 150 mA, while the duty factor ranges from 1% to 9%. Much of the workshop discussion centered on the state-of-the-art of negative hydrogen ion source (H{sup {minus}}) technology and the present experience with Penning and volume sources. In addition, other ion source technologies, for positive ions or CW applications were reviewed. Some of these sources have been operational at existing accelerator complexes and some are in the source-development stage on test stands.

  8. The Cold Neutron Chopper Spectrometer at the Spallation Neutron Source - A Review of the first 8 Years of Operation

    CERN Document Server

    Ehlers, Georg; Kolesnikov, Alexander I

    2016-01-01

    The first eight years of operation of the Cold Neutron Chopper Spectrometer (CNCS) at the Spallation Neutron Source in Oak Ridge is being reviewed. The instrument has been part of the facility user program since 2009, and more than 250 individual user experiments have been performed to date. CNCS is an extremely powerful and versatile instrument and offers leading edge performance in terms of beam intensity, energy resolution, and flexibility to trade one for another. Experiments are being routinely performed with the sample at extreme conditions: T~0.05K, p>=2GPa and B=8T can be achieved individually or in combination. In particular, CNCS is in a position to advance the state of the art with inelastic neutron scattering under pressure, and some of the recent accomplishments in this area will be presented in more detail.

  9. Fission and spallation data evaluation using induced-activity method

    CERN Document Server

    Karapetyan, G S

    2015-01-01

    The induced-activity investigations in off-line analysis performed in different experiments, concerning pre-actinide and actinide nuclei, are here presented and discussed. Generalized expressions for the determination of independent yields/cross sections of radioactive nuclei, formed in the targets, are derived and analysed. The fragment mass distribution from U-238, Th-232 and Ta-181 photofission at the bremsstrahlung end-point energies of 50 and 3500 MeV, and from Am-241, U-238 and Np-237 fission induced by 660-MeV protons, are scrutinized from the point of view of the multimodal fission approach. The results of these studies are hence compared with theoretical model calculations using the CRISP code. We subsequently discuss the complex particle-induced reaction, such as heavy-ions and deuterons, by using the thick-target thick-catcher technique and the two-step vector model framework as well. This is accomplished in order to present the investigation of the main processes (fission, spallation and (multi)fr...

  10. The COHERENT Experiment at the Spallation Neutron Source

    CERN Document Server

    Akimov, D; Awe, C; Barbeau, P S; Barton, P; Becker, B; Below, V; Bolozdynya, A; Burenkov, A; Cabrera-Palmer, B; Collar, J I; Cooper, R J; Cooper, R L; Cuesta, C; Dean, D; Detwiler, J; Efremenko, Y; Elliott, S R; Fields, N; Fox, W; Galindo-Uribarri, A; Green, M; Heath, M; Hedges, S; Herman, N; Hornback, D; Iverson, E B; Kaufman, L; Klein, S R; Khromov, A; Konovalev, A; Kumpan, A; Leadbetter, C; Li, L; Lu, W; Melikyan, A; Markoff, D; Miller, K; Middlebrook, M; Mueller, P; Naumov, P; Newby, J; Parno, D; Penttila, S; Perumpilly, G; Radford, D; Ray, H; Raybern, J; Reyna, D; Rich, G C; Rimal, D; Rudik, D; Scholberg, K; Scholz, B; Snow, W M; Sosnovchev, A; Shakirov, A; Suchyta, S; Suh, B; Tayloe, R; Thornton, R T; Tolstukhin, A; Vetter, K; Yu, C H

    2015-01-01

    The COHERENT collaboration's primary objective is to measure coherent elastic neutrino-nucleus scattering (CEvNS) using the unique, high-quality source of tens-of-MeV neutrinos provided by the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL). In spite of its large cross section, the CEvNS process has never been observed, due to tiny energies of the resulting nuclear recoils which are out of reach for standard neutrino detectors. The measurement of CEvNS has now become feasible, thanks to the development of ultra-sensitive technology for rare decay and weakly-interacting massive particle (dark matter) searches. The CEvNS cross section is cleanly predicted in the standard model; hence its measurement provides a standard model test. It is relevant for supernova physics and supernova-neutrino detection, and enables validation of dark-matter detector background and detector-response models. In the long term, precision measurement of CEvNS will address questions of nuclear structure. COHERENT...

  11. Neutron diffractometers for structural biology at spallation neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Schoenborn, B.P.; Pitcher, E. [Los Alamos National Laboratory, NM (United States)

    1994-12-31

    Spallation neutron sources are ideal for diffraction studies of proteins and oriented molecular complexes. With spoliation neutrons and their time dependent wavelength structure, it is easy to electronically select data with an optimal wavelength bandwidth and cover the whole Laue spectrum as time (wavelength) resolved snapshots. This optimized data quality with best peak-to-background ratios and provides adequate spatial and energy resolution to eliminate peak overlaps. The application of this concept will use choppers to select the desired Laue wavelength spectrum and employ focusing optics and large cylindrical {sup 3}He detectors to optimize data collection rates. Such a diffractometer will cover a Laue wavelength range from 1 to 5{Angstrom} with a flight path length of 10m and an energy resolution of 0.25{Angstrom}. Moderator concepts for maximal flux distribution within this energy range will be discussed using calculated flux profiles. Since the energy resolution required for such timed data collection in this super Laue techniques is not very high, the use of a linac only (LAMPF) spoliation target is an exciting possibility with an order of magnitude increase in flux.

  12. Beam dynamics simulation of the Spallation Neutron Source linear accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, H.; Billen, J.H.; Bhatia, T.S.

    1998-12-31

    The accelerating structure for Spallation Neutron Source (SNS) consists of a radio-frequency-quadrupole-linac (RFQ), a drift-tube-linac (DTL), a coupled-cavity-drift-tube-linac (CCDTL), and a coupled-cavity-linac (CCL). The linac is operated at room temperature. The authors discuss the detailed design of linac which accelerates an H{sup {minus}} pulsed beam coming out from RFQ at 2.5 MeV to 1000 MeV. They show a detailed transition from 402.5 MHz DTL with a 4 {beta}{lambda} structure to a CCDTL operated at 805 MHz with a 12 {beta}{lambda} structure. After a discussion of overall feature of the linac, they present an end-to-end particle simulation using the new version of the PARMILA code for a beam starting from the RFQ entrance through the rest of the linac. At 1000 MeV, the beam is transported to a storage ring. The storage ring requires a large ({+-}500-keV) energy spread. This is accomplished by operating the rf-phase in the last section of the linac so the particles are at the unstable fixed point of the separatrix. They present zero-current phase advance, beam size, and beam emittance along the entire linac.

  13. Analytical calculations and Monte-Carlo simulations of a high-resolution backscattering spectrometer for the long wavelength target station at the Spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Bordallo, H.N. E-mail: bordallo@hmi.de; Herwig, K.W.; Zsigmond, G

    2002-09-21

    Using the Monte-Carlo simulation programs McStas and VITESS, we present the design principles of the proposed high-resolution inverse geometry spectrometer on the Spallation neutron source (SNS) - long wavelength target station (LWTS). LWTS will enable the combination of large energy and momentum transfer ranges with energy resolution. Indeed the resolution of this spectrometer lie between that routinely achieved by spin echo techniques and the design goal of the high-power target station (HPTS) backscattering spectrometer. This niche of energy resolution is interesting for the study of slow motions of large objects and we are led to the domain of large molecules - polymers and biological molecules.

  14. Analytical calculations and Monte-Carlo simulations of a high-resolution backscattering spectrometer for the long wavelength target station at the Spallation neutron source

    CERN Document Server

    Bordallo, H N; Zsigmond, G

    2002-01-01

    Using the Monte-Carlo simulation programs McStas and VITESS, we present the design principles of the proposed high-resolution inverse geometry spectrometer on the Spallation neutron source (SNS) - long wavelength target station (LWTS). LWTS will enable the combination of large energy and momentum transfer ranges with energy resolution. Indeed the resolution of this spectrometer lie between that routinely achieved by spin echo techniques and the design goal of the high-power target station (HPTS) backscattering spectrometer. This niche of energy resolution is interesting for the study of slow motions of large objects and we are led to the domain of large molecules - polymers and biological molecules.

  15. Simulation of a suite of generic long-pulse neutron instruments to optimize the time structure of the European Spallation Source

    DEFF Research Database (Denmark)

    Lefmann, Kim; Klenø, Kaspar H.; Birk, Jonas Okkels;

    2013-01-01

    between 10 Hz and 25 Hz. The relative change in performance with time structure is given for each instrument, and an unweighted average is calculated. The performance of the instrument suite is proportional to (a) the peak flux and (b) the duty cycle to a power of approximately 0.3. This information......We here describe the result of simulations of 15 generic neutron instruments for the long-pulsed European Spallation Source. All instruments have been simulated for 20 different settings of the source time structure, corresponding to pulse lengths between 1 ms and 2 ms; and repetition frequencies...

  16. Conceptual moderator studies for the Spallation Neutron Source short-pulse second target station

    Science.gov (United States)

    Gallmeier, F. X.; Lu, W.; Riemer, B. W.; Zhao, J. K.; Herwig, K. W.; Robertson, J. L.

    2016-06-01

    Candidate moderator configurations for a short-pulse second target station (STS) at the Oak Ridge National Laboratory Spallation Neutron Source (SNS) have been identified using a global optimizer framework built around the MCNPX particle transport code. Neutron brightness metrics were selected as the figure-of-merit. We assumed that STS would use one out of six proton pulses produced by an SNS accelerator upgraded to operate at 1.3 GeV proton energy, 2.8 MW power and 60 Hz repetition rate. The simulations indicate that the peak brightness can be increased by a factor of 5 and 2.5 on a per proton pulse basis compared to the SNS first target station for both coupled and decoupled para-hydrogen moderators, respectively. Additional increases by factors of 3 and 2 were demonstrated for coupled and decoupled moderators, respectively, by reducing the area of neutron emission from 100 × 100 mm2 to 20 × 20 mm2. This increase in brightness has the potential to translate to an increase of beam intensity at the instruments' sample positions even though the total neutron emission of the smaller moderator is less than that of the larger. This is especially true for instruments with small samples (beam dimensions). The increased fluxes in the STS moderators come at accelerated poison and de-coupler burnout and higher radiation-induced material damage rates per unit power, which overall translate into lower moderator lifetimes. A first effort was undertaken to group decoupled moderators into a cluster collectively positioning them at the peak neutron production zone in the target and having a three-port neutron emission scheme that complements that of a cylindrical coupled moderator.

  17. Conceptual moderator studies for the Spallation Neutron Source short-pulse second target station.

    Science.gov (United States)

    Gallmeier, F X; Lu, W; Riemer, B W; Zhao, J K; Herwig, K W; Robertson, J L

    2016-06-01

    Candidate moderator configurations for a short-pulse second target station (STS) at the Oak Ridge National Laboratory Spallation Neutron Source (SNS) have been identified using a global optimizer framework built around the MCNPX particle transport code. Neutron brightness metrics were selected as the figure-of-merit. We assumed that STS would use one out of six proton pulses produced by an SNS accelerator upgraded to operate at 1.3 GeV proton energy, 2.8 MW power and 60 Hz repetition rate. The simulations indicate that the peak brightness can be increased by a factor of 5 and 2.5 on a per proton pulse basis compared to the SNS first target station for both coupled and decoupled para-hydrogen moderators, respectively. Additional increases by factors of 3 and 2 were demonstrated for coupled and decoupled moderators, respectively, by reducing the area of neutron emission from 100 × 100 mm(2) to 20 × 20 mm(2). This increase in brightness has the potential to translate to an increase of beam intensity at the instruments' sample positions even though the total neutron emission of the smaller moderator is less than that of the larger. This is especially true for instruments with small samples (beam dimensions). The increased fluxes in the STS moderators come at accelerated poison and de-coupler burnout and higher radiation-induced material damage rates per unit power, which overall translate into lower moderator lifetimes. A first effort was undertaken to group decoupled moderators into a cluster collectively positioning them at the peak neutron production zone in the target and having a three-port neutron emission scheme that complements that of a cylindrical coupled moderator.

  18. Design, status and first operations of the spallation neutron source polyphase resonant converter modulator system

    Energy Technology Data Exchange (ETDEWEB)

    Reass, W. A. (William A.); Apgar, S. E. (Sean E.); Baca, D. M. (David M.); Doss, James D.; Gonzales, J. (Jacqueline); Gribble, R. F. (Robert F.); Hardek, T. W. (Thomas W.); Lynch, M. T. (Michael T.); Rees, D. E. (Daniel E.); Tallerico, P. J. (Paul J.); Trujillo, P. B. (Pete B.); Anderson, D. E. (David E.); Heidenreich, D. A. (Dale A.); Hicks, J. D. (Jim D.); Leontiev, V. N.

    2003-01-01

    The Spallation Neutron Source (SNS) is a new 1.4 MW average power beam, 1 GeV accelerator being built at Oak Ridge National Laboratory. The accelerator requires 15 converter-modulator stations each providing between 9 and 11 MW pulses with up to a 1 .I MW average power. The converter-modulator can be described as a resonant 20 kHz polyphase boost inverter. Each converter modulator derives its buss voltage from a standard substation cast-core transformer. Each substation is followed by an SCR pre-regulator to accommodate voltage changes from no load to full load, in addition to providing a soft-start function. Energy storage is provided by self-clearing metallized hazy polypropylene traction capacitors. These capacitors do not fail short, but clear any internal anomaly. Three 'H-Bridge' IGBT transistor networks are used to generate the polyphase 20 kHz transformer primary drive waveforms. The 20 kHz drive waveforms are time-gated to generate the desired klystron pulse width. Pulse width modulation of the individual 20 lcHz pulses is utilized to provide regulated output waveforms with DSP based adaptive feedforward and feedback techniques. The boost transformer design utilizes nanocrystalline alloy that provides low core loss at design flux levels and switching frequencies. Capacitors are used on the transformer secondary networks to resonate the leakage inductance. The transformers are wound for a specific leakage inductance, not turns ratio. This design technique generates multiple secondary volts per turn as compared to the primary. With the appropriate tuning conditions, switching losses are minimized. The resonant topology has the added benefit of being deQed in a klystron fault condition, with little energy deposited in the arc. This obviates the need of crowbars or other related networks. A review of these design parameters, operational performance, production status, and OWL installation and performance to date will be presented.

  19. Conceptual moderator studies for the Spallation Neutron Source short-pulse second target station

    Energy Technology Data Exchange (ETDEWEB)

    Gallmeier, F. X., E-mail: gallmeierfz@ornl.gov; Lu, W.; Riemer, B. W.; Zhao, J. K.; Herwig, K. W.; Robertson, J. L. [Instrument and Source Division, Oak Ridge National Laboratory, P.O. Box 2008, MS6466, Oak Ridge, Tennessee 37831 (United States)

    2016-06-15

    Candidate moderator configurations for a short-pulse second target station (STS) at the Oak Ridge National Laboratory Spallation Neutron Source (SNS) have been identified using a global optimizer framework built around the MCNPX particle transport code. Neutron brightness metrics were selected as the figure-of-merit. We assumed that STS would use one out of six proton pulses produced by an SNS accelerator upgraded to operate at 1.3 GeV proton energy, 2.8 MW power and 60 Hz repetition rate. The simulations indicate that the peak brightness can be increased by a factor of 5 and 2.5 on a per proton pulse basis compared to the SNS first target station for both coupled and decoupled para-hydrogen moderators, respectively. Additional increases by factors of 3 and 2 were demonstrated for coupled and decoupled moderators, respectively, by reducing the area of neutron emission from 100 × 100 mm{sup 2} to 20 × 20 mm{sup 2}. This increase in brightness has the potential to translate to an increase of beam intensity at the instruments’ sample positions even though the total neutron emission of the smaller moderator is less than that of the larger. This is especially true for instruments with small samples (beam dimensions). The increased fluxes in the STS moderators come at accelerated poison and de-coupler burnout and higher radiation-induced material damage rates per unit power, which overall translate into lower moderator lifetimes. A first effort was undertaken to group decoupled moderators into a cluster collectively positioning them at the peak neutron production zone in the target and having a three-port neutron emission scheme that complements that of a cylindrical coupled moderator.

  20. Preparation and testing of corrosion and spallation-resistant coatings

    Energy Technology Data Exchange (ETDEWEB)

    Hurley, John P. [Univ. of North Dakota, Grand Forks, ND (United States); Cavalli, Matthew N. [Univ. of North Dakota, Grand Forks, ND (United States)

    2016-06-30

    its standard oxidation, spallation, and corrosion testing, which was scheduled for completion in the spring of 2016. However, because of commercial demands, the tests were not completed by the time of this report except some initial spallation tests at 1150°C. In those tests, several of the APMT plates separated from the CM247LC, likely because of the remaining aluminum oxide scale on the surface of the CM247LC. This implies that surface preparation may need to include machining to remove the oxide scale before bonding rather than just sandblasting. In previous tensile testing at 950°C, the breaks in the tensile samples always occurred in the APMT and not at the joints. Gasifier sampling was completed to determine what types of trace contaminants may occur in cleaned and combusted syngas and that could lead to corrosion or deposition in turbines firing coal syngas. The sampling was done from a pressurized fluidized-bed gasifier and a pressurized entrained-flow gasifier. The particles captured on a filter from syngas were typically 0.2 to 0.5 μm in diameter, whereas those captured from the combusted syngas were slightly larger and more spherical. X-ray photoelectron spectroscopy done at Oak Ridge National Laboratory showed that the particles do not contain any metals and have an atomic composition almost identical to that of the polycarbonate filter. This indicates that the particles are primarily soot-based and not formed from volatilization of metals in the gasifiers.

  1. The COHERENT Experiment at the Spallation Neutron Source

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, Steven Ray [Los Alamos National Laboratory (LANL), Los Alamos, NM (United States)

    2015-09-30

    The COHERENT collaboration's primary objective is to measure coherent elastic neutrino- nucleus scattering (CEvNS) using the unique, high-quality source of tens-of-MeV neutrinos provided by the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL). In spite of its large cross section, the CEvNS process has never been observed, due to tiny energies of the resulting nuclear recoils which are out of reach for standard neutrino detectors. The measurement of CEvNS has now become feasible, thanks to the development of ultra-sensitive technology for rare decay and weakly-interacting massive particle (dark matter) searches. The CEvNS cross section is cleanly predicted in the standard model; hence its measurement provides a standard model test. It is relevant for supernova physics and supernova-neutrino detection, and enables validation of dark-matter detector background and detector-response models. In the long term, precision measurement of CEvNS will address questions of nuclear structure. COHERENT will deploy multiple detector technologies in a phased approach: a 14-kg CsI[Na] scintillating crystal, 15 kg of p-type point-contact germanium detectors, and 100 kg of liquid xenon in a two-phase time projection chamber. Following an extensive background measurement campaign, a location in the SNS basement has proven to be neutron-quiet and suitable for deployment of the COHERENT detector suite. The simultaneous deployment of the three COHERENT detector subsystems will test the N=2 dependence of the cross section and ensure an unambiguous discovery of CEvNS. This document describes concisely the COHERENT physics motivations, sensitivity and plans for measurements at the SNS to be accomplished on a four-year timescale.

  2. Observation of fs-laser spallative ablation using soft X-ray laser probe

    Science.gov (United States)

    Nishikino, Masaharu; Hasegawa, Noboru; Tomita, Takuro; Minami, Yasuo; Eyama, Takashi; Kakimoto, Naoya; Izutsu, Rui; Baba, Motoyoshi; Kawachi, Tetsuya; Suemoto, Tohru

    2017-03-01

    The initial stages of femtosecond laser ablation of gold were observed by single-shot soft X-ray laser interferometer and reflectometer. The ablation front surface and the spallation shell dome structure were observed from the results of the soft X-ray interferogram, reflective image, and shadowgraph. The formation and evolution of soft X-ray Newton's rings (NRs) were found by reflective imaging at the early stages of the ablation dynamics. The soft X-ray NRs are caused by the interference between the bulk ablated surface and nanometer-scale thin spallation layer. The spallation layer was kept at the late timing of the ablation dynamics, and the height of that reached over 100 μm. The temporal evolution of the bulk ablated surface was observed in the ablation dynamics. From these results, we have succeeded in obtaining the temporal evolution of the ablation front exfoliated from the gold surface.

  3. Study of spallation by sub-picosecond laser driven shocks in metals

    Directory of Open Access Journals (Sweden)

    Combis P.

    2011-01-01

    Full Text Available Spallation induced by a laser driven shock has been studied for two decades on time scales of nanosecond order. The evolution of laser technologies now provides access to sources whose pulse duration is under the picosecond, corresponding to characteristic times of numerous microscopic phenomena. In this ultra-short irradiation regime, spallation experiments have been performed with time-resolved measurements of the free surface. In this solicitation type, damage occurs at small scale, leading to micrometric spalls. The VISAR measurements have been complemented with post-test observations and microtomography and compared with numerical simulations to check the models consistency of the laser-matter interaction, shock wave propagation and the dynamic damage criteria ability to reproduce spallation at this ultra-short time scale, inducing strong tensile stress states at very high strain rates.

  4. Quantitative measurement of the film interface strength by laser spallation technique

    Institute of Scientific and Technical Information of China (English)

    周明; 张永康; 蔡兰

    2001-01-01

    A novel laser spallation technique for quantitatively measuring the film interface strength is presented. Through the analysis of the physical procedure of the film spallation, a mathematical model is established based on the multiple reflections and transmissions of the stress waves within film, and a formula for calculating the interface strength and the strain rate is obtained. Using this method the interface strength of Cr stainless steel/TiN, Al/EPOXY and Fe/EPOXY are measured. A new method of wave-shape analysis is developed to judge the film spallation intuitionally, and to determine the spall moment, spall depth and spall strength directly. The film interface strength has been measured using single laser shock.

  5. Application of Origen2.1 in the decay photon spectrum calculation of spallation products

    CERN Document Server

    Hong, Shuang; Xu, Hu-Shan; Meng, Hai-Yan; Zhang, Lu; Liu, Zhao-Qing; Gao, Yu-Cui; Chen, Kang

    2016-01-01

    Origen2.1 is a widely used computer code for calculating the burnup, decay, and processing of radioactive materials. However, the nuclide library of Origen2.1 is used for existing reactors like pressurized water reactor, to calculate the photon spectrum released by the decay of spallation products, we have made specific libraries for the ADS tungsten spallation target, based on the results given by a Monte Carlo code: FLUKA. All the data used to make the Origen2.1 libraries is obtained from Nuclear structure & decay Data (NuDat2.6). The accumulated activity of spallation products and the contribution of nuclides to photon emission are given in this paper.

  6. Low/medium-Btu coal-gasification assessment program for specific sites of two New York utilities

    Energy Technology Data Exchange (ETDEWEB)

    1980-12-01

    The scope of this study is to investigate the technical and economic aspects of coal gasification to supply low- or medium-Btu gas to the two power plant boilers selected for study. This includes the following major studies (and others described in the text): investigate coals from different regions of the country, select a coal based on its availability, mode of transportation and delivered cost to each power plant site; investigate the effects of burning low- and medium-Btu gas in the selected power plant boilers based on efficiency, rating and cost of modifications and make recommendations for each; and review the technical feasibility of converting the power plant boilers to coal-derived gas. The following two coal gasification processes have been used as the basis for this Study: the Combustion Engineering coal gasification process produces a low-Btu gas at approximately 100 Btu/scf at near atmospheric pressure; and the Texaco coal gasification process produces a medium-Btu gas at 292 Btu/scf at 800 psig. The engineering design and economics of both plants are described. Both plants meet the federal, state, and local environmental requirements for air quality, wastewater, liquid disposal, and ground level disposal of byproduct solids. All of the synthetic gas alternatives result in bus bar cost savings on a yearly basis within a few years of start-up because the cost of gas is assumed to escalate at a lower rate than that of fuel oil, approximately 4 to 5%.

  7. The test beamline of the European Spallation Source - Instrumentation development and wavelength frame multiplication

    DEFF Research Database (Denmark)

    Woracek, R.; Hofmann, T.; Bulat, M.

    2016-01-01

    The European Spallation Source (ESS), scheduled to start operation in 2020, is aiming to deliver the most intense neutron beams for experimental research of any facility worldwide. Its long pulse time structure implies significant differences for instrumentation compared to other spallation sources...... which, in contrast, are all providing short neutron pulses. In order to enable the development of methods and technology adapted to this novel type of source well in advance of the first instruments being constructed at ESS, a test beamline (TBL) was designed and built at the BER II research reactor...

  8. Present status of spallation target development. JAERI/KEK Joint Project

    Energy Technology Data Exchange (ETDEWEB)

    Hino, R.; Kaminaga, M.; Haga, K. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment] [and others

    2001-03-01

    The Japan Atomic Energy Research Institute (JAERI) and the High Energy Accelerator Research Organization (KEK) are promoting a plan to construct a neutron scattering facility under the JAERI/KEK Joint Project. Design and R and D works are being carried out vigorously for realizing the mercury target system consisting of the mercury target, moderators and reflectors working as a spallation neutron source, as well as a remote handling system for exchanging such components which will be highly irradiated. This report introduces an outline of the present status of design and development activities on the spallation target system. (author)

  9. Application of Origen2.1 in the decay photon spectrum calculation of spallation products

    OpenAIRE

    Hong, Shuang; Yang, Yong-Wei; Xu, Hu-Shan; Meng, Hai-Yan; Zhang, Lu; Liu, Zhao-Qing; Gao, Yu-Cui; Chen, Kang

    2016-01-01

    Origen2.1 is a widely used computer code for calculating the burnup, decay, and processing of radioactive materials. However, the nuclide library of Origen2.1 is used for existing reactors like pressurized water reactor, to calculate the photon spectrum released by the decay of spallation products, we have made specific libraries for the ADS tungsten spallation target, based on the results given by a Monte Carlo code: FLUKA. All the data used to make the Origen2.1 libraries is obtained from N...

  10. R&D of A MW-class solid-target for a spallation neutron source

    Science.gov (United States)

    Kawai, Masayoshi; Furusaka, Michihiro; Kikuchi, Kenji; Kurishita, Hiroaki; Watanabe, Ryuzo; Li, Jing-Feng; Sugimoto, Katsuhisa; Yamamura, Tsutomu; Hiraoka, Yutaka; Abe, Katsunori; Hasegawa, Akira; Yoshiie, Masatoshi; Takenaka, Hiroyuki; Mishima, Katsuichiro; Kiyanagi, Yoshiaki; Tanabe, Tetsuo; Yoshida, Naoaki; Igarashi, Tadashi

    2003-05-01

    R&D for a MW-class solid target composed of tungsten was undertaken to produce a pulsed intense neutron source for a future neutron scattering-facility. In order to solve the corrosion of tungsten, tungsten target blocks were clad with tantalum by means of HIP'ing, brazing and electrolytic coating in a molten salt bath. The applicability of the HIP'ing method was tested through fabricating target blocks for KENS (spallation neutron source at KEK). A further investigation to certify the optimum HIP conditions was made with the small punch test method. The results showed that the optimum temperature was 1500 °C at which the W/Ta interface gave the strongest fracture strength. In the case of the block with a hole for thermocouple, it was found that the fabrication preciseness of a straight hole and a tantalum sheath influenced the results. The development of a tungsten stainless-steel alloy was tried to produce a bare tungsten target, using techniques in powder metallurgy. Corrosion tests for various tungsten alloys were made while varying the water temperature and velocity. The mass loss of tungsten in very slow water at 180 °C was as low as 0.022 mg/y, but increased remarkably with water velocity. Simulation experiments for radiation damage to supplement the STIP-III experiments were made to investigate material hardening by hydrogen and helium, and microstructures irradiated by electrons. Both experiments showed consistent results on the order of the dislocation numbers and irradiation hardness among the different tungsten materials. Thermal-hydraulic designs were made for two types of solid target system of tungsten: slab and rod geometry as a function of the proton beam power. The neutronic performance of a solid target system was compared with that of mercury target based on Monte Carlo calculations by using the MCNP code.

  11. Analysis of radiation environmental safety for China's Spallation Neutron Source (CSNS)

    Science.gov (United States)

    Wang, Qing-Bin; Wu, Qing-Biao; Ma, Zhong-Jian; Zhang, Qing-Jiang; Li, Nan; Wu, Jing-Min; Liu, Jian; Zhang, Gang

    2010-07-01

    The China Spallation Neutron Source (CSNS) is going to be located in Dalang Town, Dongguan City in the Guangdong Province. In this paper we report the results of the parameters related with environment safety based on experiential calculations and Monte Carlo simulations. The main project of the accelerator is an under ground construction. On top there is a 0.5 m concrete and 5.0 m soil covering for shielding, which can reduce the dose out of the tunnel's top down to 0.2 μSv/h. For the residents on the boundary of the CSNS, the dose produced by skyshine, which is caused by the penetrated radiation leaking from the top of the accelerator, is no more than 0.68 μSv/a. When CSNS is operating normally, the maximal annual effective dose due to the emission of gas from the tunnel is 2.40×10-3 mSv/a to the public adult, and 2.29×10-3 mSv/a to a child, both values are two orders of magnitude less than the limiting value for control and management. CSNS may give rise to an activation of the soil and groundwater in the nearest tunnels, where the main productions are 3H, 7Be, 22Na, 54Mn, etc. But the specific activity is less than the exempt specific activity in the national standard GB13376-92. So it is safe to say that the environmental impact caused by the activation of soil and groundwater is insignificant. To sum up, for CSNS, as a powerful neutron source device, driven by a high-energy high-current proton accelerator, a lot of potential factors affecting the environment exist. However, as long as effective shieldings for protection are adopted and strict rules are drafted, the environmental impact can be kept under control within the limits of the national standard.

  12. The spallation in reverse kinematics: what for a coincidence measurement?; La spallation en cinematique inverse: pourquoi faire une mesure en coincidence?

    Energy Technology Data Exchange (ETDEWEB)

    Ducret, J.E

    2006-07-15

    The Spaladin installation has been designed to study spallation reactions in reverse kinematics. Furthermore, the heavy and light fragments are detected by coincidence which allows us to get an instantaneous picture of the reaction at a level of accuracy better than that obtained through inclusive measurement. The first part is dedicated to the theoretical description of the different mechanisms involved in the spallation reactions. In the second part we describe the Spaladin installation and report some results on the reaction: Fe{sup 56} + p at an energy of 1 GeV/nucleon. In the third part we expose the performance of the installation through its simulation with the Geant-IV model. We present a study about the sensitivity of the Spaladin installation to theoretical predictions. The fourth part is dedicated to the future experiments that will be performed with the Spaladin installation. (A.C.)

  13. Preparation and Testing of Corrosion and Spallation-Resistant Coatings

    Energy Technology Data Exchange (ETDEWEB)

    Hurley, John

    2015-11-01

    with the Rene 80. One-inch-diameter buttons were machined from each of the bonded blocks and sent to Siemens for standard oxidation, spallation, and corrosion testing, which should be complete in the spring of 2016.

  14. A randomized, double blind, placebo-controlled, multicenter phase II trial of Allisartan Isoproxil in essential hypertensive population at low-medium risk.

    Science.gov (United States)

    Li, Ying; Li, Xiao-hui; Huang, Zhi-jun; Yang, Guo-ping; Zhang, Guo-gang; Zhao, Shui-ping; Guo, Ying; Lu, Shi-juan; Ma, Jian-lin; Meng, Fan-bo; Chen, Ping; Yuan, Hong

    2015-01-01

    Angiotensin II receptor blockers (ARBs) is a well-tolerated class of antihypertensive agents, exhibiting effective antihypertensive and cardiovascular protective function. The objective of the study was to examine the efficacy and safety of Allisartan Isoproxil, a newly developed, selective, nonpeptide blocker of the angiotensin II type 1 receptor (AT1R), in essential hypertensive patients at low-medium risk. A Phase II prospective, randomized, double-blind, placebo-controlled, multicenter trial comparing Allisartan Isoproxil 240mg versus placebo was conducted in essential hypertensive patients at low-medium risk at 8 sites in China. After a 2-week placebo baseline period, 275 patients received once-daily treatment with Allisartan Isoproxil 240mg or placebo randomly for 8 weeks. Systolic/diastolic blood pressure (SBP/DBP) was measured at week 2, 4 and 8. By the end of treatment, mean reductions from baseline of SBP and DBP in Allisartan Isoproxil and placebo groups were 14.5/10.4 and 8.3/7.7 mmHg, respectively (Psafety and tolerability, there were no report of death and serious adverse event (SAE) in all subjects. There was no difference of frequency between two groups in adverse event (AE) and adverse drug reaction (ADR) (P>0.05). No one withdraw because of an ADR in two groups. 124 patients received additional 56 weeks treatment with Allisartan Isoproxil and 84 of them completed the study. The rate of effective BP control kept up to 80% since week 24. No significant clinical change was observed and ADRs were generally mild or moderate during the long-term study. Allisartan Isoproxil 240mg was effective and safe for essential hypertension patients at low-medium risk. http://www.chictr.org/cn/ ChiCTR-TRC-10000886.

  15. A randomized, double blind, placebo-controlled, multicenter phase II trial of Allisartan Isoproxil in essential hypertensive population at low-medium risk.

    Directory of Open Access Journals (Sweden)

    Ying Li

    Full Text Available Angiotensin II receptor blockers (ARBs is a well-tolerated class of antihypertensive agents, exhibiting effective antihypertensive and cardiovascular protective function. The objective of the study was to examine the efficacy and safety of Allisartan Isoproxil, a newly developed, selective, nonpeptide blocker of the angiotensin II type 1 receptor (AT1R, in essential hypertensive patients at low-medium risk.A Phase II prospective, randomized, double-blind, placebo-controlled, multicenter trial comparing Allisartan Isoproxil 240mg versus placebo was conducted in essential hypertensive patients at low-medium risk at 8 sites in China. After a 2-week placebo baseline period, 275 patients received once-daily treatment with Allisartan Isoproxil 240mg or placebo randomly for 8 weeks. Systolic/diastolic blood pressure (SBP/DBP was measured at week 2, 4 and 8. By the end of treatment, mean reductions from baseline of SBP and DBP in Allisartan Isoproxil and placebo groups were 14.5/10.4 and 8.3/7.7 mmHg, respectively (P0.05. No one withdraw because of an ADR in two groups. 124 patients received additional 56 weeks treatment with Allisartan Isoproxil and 84 of them completed the study. The rate of effective BP control kept up to 80% since week 24. No significant clinical change was observed and ADRs were generally mild or moderate during the long-term study.Allisartan Isoproxil 240mg was effective and safe for essential hypertension patients at low-medium risk.http://www.chictr.org/cn/ ChiCTR-TRC-10000886.

  16. Production of Actinium-225 via High Energy Proton Induced Spallation of Thorium-232

    Energy Technology Data Exchange (ETDEWEB)

    Harvey, James T.; Nolen, Jerry; Vandergrift, George; Gomes, Itacil; Kroc, Tom; Horwitz, Phil; McAlister, Dan; Bowers, Del; Sullivan, Vivian; Greene, John

    2011-12-30

    The science of cancer research is currently expanding its use of alpha particle emitting radioisotopes. Coupled with the discovery and proliferation of molecular species that seek out and attach to tumors, new therapy and diagnostics are being developed to enhance the treatment of cancer and other diseases. This latest technology is commonly referred to as Alpha Immunotherapy (AIT). Actinium-225/Bismuth-213 is a parent/daughter alpha-emitting radioisotope pair that is highly sought after because of the potential for treating numerous diseases and its ability to be chemically compatible with many known and widely used carrier molecules (such as monoclonal antibodies and proteins/peptides). Unfortunately, the worldwide supply of actinium-225 is limited to about 1,000mCi annually and most of that is currently spoken for, thus limiting the ability of this radioisotope pair to enter into research and subsequently clinical trials. The route proposed herein utilizes high energy protons to produce actinium-225 via spallation of a thorium-232 target. As part of previous R and D efforts carried out at Argonne National Laboratory recently in support of the proposed US FRIB facility, it was shown that a very effective production mechanism for actinium-225 is spallation of thorium-232 by high energy proton beams. The base-line simulation for the production rate of actinium-225 by this reaction mechanism is 8E12 atoms per second at 200 MeV proton beam energy with 50 g/cm2 thorium target and 100 kW beam power. An irradiation of one actinium-225 half-life (10 days) produces {approx}100 Ci of actinium-225. For a given beam current the reaction cross section increases slightly with energy to about 400 MeV and then decreases slightly for beam energies in the several GeV regime. The object of this effort is to refine the simulations at proton beam energies of 400 MeV and above up to about 8 GeV. Once completed, the simulations will be experimentally verified using 400 MeV and 8 Ge

  17. Thermal-hydraulic analysis of LBE spallation target for accelerator-driven systems

    Indian Academy of Sciences (India)

    Aniseh Ahmed Atef Abdalla; Jiyang Yu; Yongwel Yang

    2013-01-01

    In an accelerator-driven subcritical system (ADS), a high-performance spallation neutron source is used to feed the subcritical reactor. Neutron generation depends on the proton beam intensity. If the beam intensity is increased by a given factor, the number of generated neutrons will increase. The mechanism yielding a high rate of neutron production per energy is the spallation process, and this mechanism produces very high-energy deposition in the spallation target material. Producing a high rate of neutrons is accompanied by creation of problems of decay heat cooling and radiological protection. As a first step in designing a full-scale industrial ADS, a small-scale experimental ADS, which is similar to the European experimental ADS (XADS) is analysed. The analysis presented in this paper is based on lead–bismuth eutectic (LBE) cooled XADS-type experimental reactors, designed during the European experimental (PDS-XADS) project. Computational fluid dynamics analysis has been carried out for the spallation target. Steady-state behaviour and shear stress transport turbulence model with the automatic wall treatment were applied in the present analysis.

  18. Study on target spallation reaction cross sections induced by high energy neutrons and heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Takashi [Tohoku Univ., Sendai (Japan). Cyclotron and Radioisotope Center

    1996-03-01

    The target spallation reaction cross sections of neutrons and heavy ions which have not been observed are determined in this paper. The object of this work is to make clear the differences between the spallation reaction cross section of neutron and that of proton by comparing the obtained value of neutron with the known value of proton. To this end, the quasi monochromatic neutron field of 20{approx}50 MeV was developed in 4 cyclotrons, INS, CYRIC, TIARA and RIKEN. The nuclear spallation reaction cross sections of C, Al and Bi were measured in the above field and the distribution of nuclear spallation reaction products in Cu determined by C ion beam of HIMAC. {sup 12}C(n,2n){sup 11}C reaction cross section shows the maximum value of about 20 mb at near 40{approx}50 MeV and then the value gradually decreased to 10 mb. The cross sections of {sup 209}Bi(n,Xn) are shown. The distribution of {sup 61}Cu is lower at the entrance and higher in the depth. (S.Y.)

  19. Stress and adhesion of chromia-rich scales on ferritic stainless steels in relation with spallation

    Directory of Open Access Journals (Sweden)

    A. Galerie

    2004-03-01

    Full Text Available The relation between chromia scale spallation during oxidation or cooling down of ferritic stainless steels is generally discussed in terms of mechanical stresses induced by volume changes or differential thermal expansion. In the present paper, growth and thermal stress measurements in scales grown on different ferritic steel grades have shown that the main stress accumulation occurs during isothermal scale growth and that thermal stresses are of minor importance. However, when spallation occurs, it is always during cooling down. Steel-oxide interface undulation seems to play a major role at this stage, thus relating spallation to the metal mechanical properties, thickness and surface preparation. A major influence on spallation of the minor stabilizing elements of the steels was observed which could not be related to any difference in stress state. Therefore, an original inverted blister test was developed to derive quantitative values of the metal-oxide adhesion energy. These values clearly confirmed that this parameter was influenced by scale thickness and by minor additions, titanium greatly increasing adhesion whereas niobium decreased it.

  20. Thermal hydraulic studies of lead–bismuth eutectic spallation target of CIADS

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Kang [Institute of Modern Physics, Chinese Academy of Sciences, 509 Nanchang Rd., Lanzhou, Gansu 730000 (China); University of Chinese Academy of Sciences, 19 A Yuquan Rd, Shijingshan District, Beijing 100049 (China); Yang, Yongwei, E-mail: yangyongwei@impcas.ac.cn [Institute of Modern Physics, Chinese Academy of Sciences, 509 Nanchang Rd., Lanzhou, Gansu 730000 (China); Fan, Deliang; Gao, Yucui [Institute of Modern Physics, Chinese Academy of Sciences, 509 Nanchang Rd., Lanzhou, Gansu 730000 (China)

    2016-08-15

    Highlights: • A 3-D fluid-solid coupling thermal-hydraulic analysis is made for the LBE target. • The reactor and the spallation target is coupled in thermal process. • The heat transfer between the inlet and outlet of the spallation target is taken into account. - Abstract: For the China Initiative Accelerator Driven System (CIADS), it includes three sub-systems: accelerator, spallation target, and sub-critical reactor. The sub-system of spallation target is an important component of the CIADS, which is coupled with the other two sub-systems. The proton beam from the accelerator with an energy of 250 MeV and a current intensity of 2 mA reacts with the nuclei of the lead–bismuth eutectic (LBE), approximately 0.5 MW of heat is deposited in the target zone, which must be removed by circulating the LBE. To reach the goal, we carried out the study by using the Computational Fluid Dynamics (CFD) software FLUENT, to study the flow patterns and temperature distribution in the target zone. For these simulations, the heat transferred from the sub-critical reactor was taken into account. The results indicated that the heat deposited in the target zone can be removed safely.

  1. Comparison of Different INC Physical Models of MCNPX to Compute Spallation Neutronics of LBE Target

    Science.gov (United States)

    Feghhi, Seyed Amir Hossein; Gholamzadeh, Zohreh; Tenreiro, Claudio; Alipoor, Zahra

    2015-04-01

    Spallation particles can utilize in different fields such as neutron scattering studies, external source for burning spent fuel as well as running subcritical reactors. Different computational particle transport codes are widely used to model spallation process into the heavy targets. Among these codes, MCNPX 2.6.0 comprises various intra nuclear cascade models for spallation calculations. Impact of different intra nuclear cascade models on calculation of neutronic parameters of LBE target has been evaluated in this work. Escaped neutron yield, energy deposition and residual nuclei production in the spallation target has been calculated using the physical models. A comparison between the computational and experimental has been carried out to validate the computational data. The simulation data showed there is a good conformity between the obtained data from Bertini/Drenser and Isabel/Drenser. The data achieved by Bertini/Abla and Isabel/Abla models are close to each other for the studied parameters as well. Among the studied models, CEM showed more discrepancies with experimental and other computational data. According to the obtained data, INCL4/Drenser, INCL4/Abla and Isabel/Drenser models can meet more agreements with experimental data.

  2. Effect of Substrate Thickness on Oxide Scale Spallation for Solid Oxide Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Wenning N.; Sun, Xin; Stephens, Elizabeth V.; Khaleel, Mohammad A.

    2011-07-01

    In this paper, the effect of the ferritic substrate's thickness on the delamination/spallation of the oxide scale was investigated experimentally and numerically. At the high-temperature oxidation environment of solid oxide fuel cells (SOFCs), a combination of growth stress with thermal stresses may lead to scale delamination/buckling and eventual spallation during SOFC stack cooling, even leading to serious degradation of cell performance. The growth stress is induced by the growth of the oxide scale on the scale/substrate interface, and thermal stress is induced by a mismatch of the coefficient of thermal expansion between the oxide scale and the substrate. The numerical results show that the interfacial shear stresses, which are the driving force of scale delamination between the oxide scale and the ferritic substrate, increase with the growth of the oxide scale and also with the thickness of the ferritic substrate; i.e., the thick ferritic substrate can easily lead to scale delamination and spallation. Experimental observation confirmed the predicted results of the delamination and spallation of the oxide scale on the ferritic substrate.

  3. Migration of radionuclides in a gas cooled solid state spallation target

    DEFF Research Database (Denmark)

    Jørgensen, Thomas; Severin, Gregory; Jensen, Mikael

    2015-01-01

    The current design of the ESS (European Spallation Source) program proposes a rotating solid tungsten target cooled by helium gas and a pulsed beam of protons. For safety reasons any design has to address whether or not the induced radionuclidic isotopes in the target migrate. In this paper we ha...

  4. Shielding examinations for the European Spallation Source ESS: Update for use by EURISOL

    CERN Document Server

    Rainer Moormann

    The Moyer model used in shielding design of the ESS accelerator is outlined in detail and relevant results are presented. General guidelines for shielding of a large spallation based system are presented, which take into account accidental beam losses and enhanced beam losses during start-up, too.

  5. Power

    DEFF Research Database (Denmark)

    Elmholdt, Claus Westergård; Fogsgaard, Morten

    2016-01-01

    In this chapter, we will explore the dynamics of power in processes of creativity, and show its paradoxical nature as both a bridge and a barrier to creativity in organisations. Recent social psychological experimental research (Slighte, de Dreu & Nijstad, 2011) on the relation between power...... and creativity suggests that when managers give people the opportunity to gain power and explicate that there is reason to be more creative, people will show a boost in creative behaviour. Moreover, this process works best in unstable power hierarchies, which implies that power is treated as a negotiable...... and floating source for empowering people in the organisation. We will explore and discuss here the potentials, challenges and pitfalls of power in relation to creativity in the life of organisations today. The aim is to demonstrate that power struggles may be utilised as constructive sources of creativity...

  6. Spallation Neutron Spectrum on a Massive Lead/Paraffin Target Irradiated with 1 GeV Protons

    CERN Document Server

    Adam, J; Barashenkov, V S; Brandt, R; Golovatiouk, V M; Kalinnikov, V G; Katovsky, K; Krivopustov, M I; Kumar, V; Kumawat, H; Odoj, R; Pronskikh, V S; Solnyshkin, A A; Stegailov, V I; Tsoupko-Sitnikov, V M; Westmeier, W

    2004-01-01

    The spectra of gamma-ray emitted by decaying residual nuclei, produced by spallation neutrons with (n, xn), (n,xnyp), (n,p), (n,gamma) reactions in activation threshold detectors - namely, ^{209}Bi, ^{197}Au, ^{59}Co, ^{115}In, ^{232}Th, were measured in the Laboratory of Nuclear Problems (LNP), JINR, Dubna, Russia. Spallation neutrons were generated by bombarding a 20 cm long cylindrical lead target, 8 cm in diameter, surrounded by a 6 cm thick layer of paraffin moderator, with a 1 GeV proton beam from the Nuclotron accelerator. Reaction rates and spallation neutron spectrum were measured and compared with CASCADE code calculations.

  7. Mechanisms of spallation of electron beam physical vapor deposited thermal barrier coatings with and without platinum aluminide bond coat ridges

    Energy Technology Data Exchange (ETDEWEB)

    Vaidyanathan, K.; Gell, M. [Connecticut Univ., Storrs, CT (United States). Dept. of Metallurgy; Jordan, E. [Dept. Mechanical Engineering, University of Connecticut, CT-06269, Storrs (United States)

    2000-11-01

    Grain boundary ridges, that form on the surface of platinum aluminide [(Ni,Pt)Al] bond coats prior to the deposition of the yttria stabilized zirconia ceramic layer by the electron beam physical vapor deposition (EB-PVD) process, were shown to be the sites for spallation damage initiation in (Ni,Pt)Al/EB-PVD thermal barrier coatings. When these ridges are removed prior to deposition of the ceramic layer, a 3 x life improvement is achieved. This study compares the spallation mechanisms in specimens with and without bond coat ridges, in order to explain the improvement in spallation life. (orig.)

  8. Low/medium Btu coal-gasification assessment program for potential users in New Jersey. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Bianco, J. [BRISC; Schavlan, S. [BRISC; Ku, W. S. [PSE& G; Piascik, T. M. [PSE& G; Hynds, J. A. [PSE& G; West, A. [SDC

    1981-01-01

    In order to evaluate the potential for coal utilization, a preliminary technical and economic assessment of district coal gasification in New Jersey was conducted. This evaluation addressed the possibility of installing a coal gasification plant to use a high sulfur eastern coal to produce a medium Btu content gas (MBG) having a heating value of approximately 300 Btu/SCF. In addition, the work also appraised the regulatory, environmental and marketing, and financial considerations of such a facility. The preliminary study evaluation has manifested an overall technical and economic feasibility for producing a medium Btu quality gas (MBG) from coal at PSE and G's Sewaren Generating Station in New Jersey. The production of MBG for use in on-site power plant boilers or for distribution to industrial customers appears to be economically attractive. The economic attractiveness of MBG is very dependent on the location of sufficient numbers of industrial customers near the gasification facilities and on high utilization of the gasification plant. The Sewaren Generating Station was identified as potentially the most suitable site for a gasification plant. The Texaco Coal Gasification Process was selected as the gasifier type due to a combination of efficiency and pilot plant experience. It is projected that a nominal 2000 tons-per-day coal gasification plant would supply supplemental utility boiler fuel, fuel grade methanol and some by-products.

  9. Development of a Equipment to Measure Gas Transport Properties: Application to Study Mixtures of Candidates Buffer Materials for Low-Medium Level Waste Repositories

    Energy Technology Data Exchange (ETDEWEB)

    Martin, P.L.; Barcala, J.M.; Oller, J.C.

    2002-07-01

    This report describes the design, the construction and a testing of a system set-up for the measurement of gas transport, created at CIEMAT, and its application to study mixtures of candidate buffer materials for Low-Medium Level Waste Repertories. The measure of the gas flows is carried on by mass flow meters of several ranges, white the pressure of the applied within the sample is controlled. Two National l Instrument's acquisition system that permits the control and recording of the parameters. A specific application developed for this test, with National Instruments LabWIEW DSC, permits to mange the system. A client interface lets to follow the experiment course from a remote location through Internet. (Author) 21 refs.

  10. The Proportion of Anemia Associated with Iron Deficiency in Low, Medium, and High Human Development Index Countries: A Systematic Analysis of National Surveys

    Directory of Open Access Journals (Sweden)

    Nicolai Petry

    2016-11-01

    Full Text Available Iron deficiency is commonly assumed to cause half of all cases of anemias, with hereditary blood disorders and infections such as hookworm and malaria being the other major causes. In countries ranked as low, medium, and high by the Human Development Index, we conducted a systematic review of nationally representative surveys that reported the prevalence of iron deficiency, iron deficiency anemia, and anemia among pre-school children and non-pregnant women of reproductive age. Using random effects meta-analyses techniques, data from 23 countries for pre-school children and non-pregnant women of reproductive age was pooled, and the proportion of anemia attributable to iron deficiency was estimated by region, inflammation exposure, anemia prevalence, and urban/rural setting. For pre-school children and non-pregnant women of reproductive age, the proportion of anemia associated with iron deficiency was 25.0% (95% CI: 18.0, 32.0 and 37.0% (95% CI: 28.0, 46.0, respectively. The proportion of anemia associated with iron deficiency was lower in countries where anemia prevalence was >40%, especially in rural populations (14% for pre-school children; 16% for non-pregnant women of reproductive age, and in countries with very high inflammation exposure (20% for pre-school children; 25% for non-pregnant women of reproductive age. Despite large heterogeneity, our analyses suggest that the proportion of anemia associated with iron deficiency is lower than the previously assumed 50% in countries with low, medium, or high Human Development Index ranking. Anemia-reduction strategies and programs should be based on an analysis of country-specific data, as iron deficiency may not always be the key determinant of anemia.

  11. The Proportion of Anemia Associated with Iron Deficiency in Low, Medium, and High Human Development Index Countries: A Systematic Analysis of National Surveys

    Science.gov (United States)

    Petry, Nicolai; Olofin, Ibironke; Hurrell, Richard F.; Boy, Erick; Wirth, James P.; Moursi, Mourad; Donahue Angel, Moira; Rohner, Fabian

    2016-01-01

    Iron deficiency is commonly assumed to cause half of all cases of anemias, with hereditary blood disorders and infections such as hookworm and malaria being the other major causes. In countries ranked as low, medium, and high by the Human Development Index, we conducted a systematic review of nationally representative surveys that reported the prevalence of iron deficiency, iron deficiency anemia, and anemia among pre-school children and non-pregnant women of reproductive age. Using random effects meta-analyses techniques, data from 23 countries for pre-school children and non-pregnant women of reproductive age was pooled, and the proportion of anemia attributable to iron deficiency was estimated by region, inflammation exposure, anemia prevalence, and urban/rural setting. For pre-school children and non-pregnant women of reproductive age, the proportion of anemia associated with iron deficiency was 25.0% (95% CI: 18.0, 32.0) and 37.0% (95% CI: 28.0, 46.0), respectively. The proportion of anemia associated with iron deficiency was lower in countries where anemia prevalence was >40%, especially in rural populations (14% for pre-school children; 16% for non-pregnant women of reproductive age), and in countries with very high inflammation exposure (20% for pre-school children; 25% for non-pregnant women of reproductive age). Despite large heterogeneity, our analyses suggest that the proportion of anemia associated with iron deficiency is lower than the previously assumed 50% in countries with low, medium, or high Human Development Index ranking. Anemia-reduction strategies and programs should be based on an analysis of country-specific data, as iron deficiency may not always be the key determinant of anemia. PMID:27827838

  12. The Proportion of Anemia Associated with Iron Deficiency in Low, Medium, and High Human Development Index Countries: A Systematic Analysis of National Surveys.

    Science.gov (United States)

    Petry, Nicolai; Olofin, Ibironke; Hurrell, Richard F; Boy, Erick; Wirth, James P; Moursi, Mourad; Donahue Angel, Moira; Rohner, Fabian

    2016-11-02

    Iron deficiency is commonly assumed to cause half of all cases of anemias, with hereditary blood disorders and infections such as hookworm and malaria being the other major causes. In countries ranked as low, medium, and high by the Human Development Index, we conducted a systematic review of nationally representative surveys that reported the prevalence of iron deficiency, iron deficiency anemia, and anemia among pre-school children and non-pregnant women of reproductive age. Using random effects meta-analyses techniques, data from 23 countries for pre-school children and non-pregnant women of reproductive age was pooled, and the proportion of anemia attributable to iron deficiency was estimated by region, inflammation exposure, anemia prevalence, and urban/rural setting. For pre-school children and non-pregnant women of reproductive age, the proportion of anemia associated with iron deficiency was 25.0% (95% CI: 18.0, 32.0) and 37.0% (95% CI: 28.0, 46.0), respectively. The proportion of anemia associated with iron deficiency was lower in countries where anemia prevalence was >40%, especially in rural populations (14% for pre-school children; 16% for non-pregnant women of reproductive age), and in countries with very high inflammation exposure (20% for pre-school children; 25% for non-pregnant women of reproductive age). Despite large heterogeneity, our analyses suggest that the proportion of anemia associated with iron deficiency is lower than the previously assumed 50% in countries with low, medium, or high Human Development Index ranking. Anemia-reduction strategies and programs should be based on an analysis of country-specific data, as iron deficiency may not always be the key determinant of anemia.

  13. Synthesis of neutron-rich transuranic nuclei in fissile spallation targets

    CERN Document Server

    Mishustin, Igor; Pshenichnov, Igor; Greiner, Walter

    2014-01-01

    A possibility of synthesizing neutron-reach super-heavy elements in spallation targets of Accelerator Driven Systems (ADS) is considered. A dedicated software called Nuclide Composition Dynamics (NuCoD) was developed to model the evolution of isotope composition in the targets during a long-time irradiation by intense proton and deuteron beams. Simulation results show that transuranic elements up to Bk-249 can be produced in multiple neutron capture reactions in macroscopic quantities. However, the neutron flux achievable in a spallation target is still insufficient to overcome the so-called fermium gap. Further optimization of the target design, in particular, by including moderating material and covering it by a reflector will turn ADS into an alternative source of transuranic elements in addition to nuclear fission reactors.

  14. Systematic neutron guide misalignment for an accelerator-driven spallation neutron source

    Science.gov (United States)

    Zendler, C.; Bentley, P. M.

    2016-08-01

    The European Spallation Source (ESS) is a long pulse spallation neutron source that is currently under construction in Lund, Sweden. A considerable fraction of the 22 planned instruments extend as far as 75-150 m from the source. In such long beam lines, misalignment between neutron guide segments can decrease the neutron transmission significantly. In addition to a random misalignment from installation tolerances, the ground on which ESS is built can be expected to sink with time, and thus shift the neutron guide segments further away from the ideal alignment axis in a systematic way. These systematic errors are correlated to the ground structure, position of buildings and shielding installation. Since the largest deformation is expected close to the target, even short instruments might be noticeably affected. In this study, the effect of this systematic misalignment on short and long ESS beam lines is analyzed, and a possible mitigation by overillumination of subsequent guide sections investigated.

  15. An apparatus for studying spallation neutrons in the Aberdeen Tunnel laboratory

    CERN Document Server

    Blyth, S C; Chen, X C; Chu, M C; Hahn, R L; Ho, T H; Hsiung, Y B; Hu, B Z; Kwan, K K; Kwok, M W; Kwok, T; Lau, Y P; Lee, K P; Leung, J K C; Leung, K Y; Lin, G L; Lin, Y C; Luk, K B; Luk, W H; Ngai, H Y; Ngan, S Y; Pun, C S J; Shih, K; Tam, Y H; Tsang, R H M; Wang, C H; Wong, C M; Wong, H L; Wong, H H C; Wong, K K; Yeh, M

    2013-01-01

    In this paper, we describe the design, construction and performance of an apparatus installed in the Aberdeen Tunnel laboratory in Hong Kong for studying spallation neutrons induced by cosmic-ray muons under a vertical rock overburden of 611 meter water equivalent (m.w.e.). The apparatus comprises of six horizontal layers of plastic-scintillator hodoscopes for determining the direction and position of the incident cosmic-ray muons. Sandwiched between the hodoscope planes is a neutron detector filled with 650 kg of liquid scintillator doped with about 0.06% of Gadolinium by weight for improving the e?ciency of detecting the spallation neutrons. Performance of the apparatus is also presented.

  16. SPALLATION ANALYSIS WITH A CLOSED TRANS-SCALE FORMULATION OF DAMAGE EVOLUTION

    Institute of Scientific and Technical Information of China (English)

    WANG Haiying; BAI Yilong; XIA Mengfen; KE Fujiu

    2004-01-01

    A closed, trans-scale formulation of damage evolution based on the statistical microdamage mechanics is summarized in this paper. The dynamic function of damage bridges the mesoscopic and macroscopic evolution of damage. The spallation in an aluminium plate is studied with this formulation. It is found that the damage evolution is governed by several dimensionless parameters,i.e., imposed Deborah numbers De* and De, Mach number M and damage number S. In particular,the most critical mode of the macroscopic damage evolution, i.e., the damage localization, is determined by Deborah number De*. Deborah number De* reflects the coupling and competition between the macroscopic loading and the microdamage growth. Therefore, our results reveal the multi-scale nature of spallation. In fact, the damage localization results from the nonlinearity of the microdamage growth. In addition, the dependence of the damage rate on imposed Deborah numbers De* and De,Mach number M and damage number S is discussed.

  17. Challenges and design solutions of the liquid hydrogen circuit at the European Spallation Source

    Science.gov (United States)

    Gallimore, S.; Nilsson, P.; Sabbagh, P.; Takibayev, A.; Weisend, J. G., II; Beßler, Y.; Klaus, M.

    2014-01-01

    The European Spallation Source (ESS), Lund, Sweden will be a 5MW long-pulse neutron spallation research facility and will enable new opportunities for researchers in the fields of life sciences, energy, environmental technology, cultural heritage and fundamental physics. Neutrons are produced by accelerating a high-energy proton beam into a rotating helium-cooled tungsten target. These neutrons pass through moderators to reduce their energy to an appropriate range (< 5 meV for cold neutrons); two of which will use liquid hydrogen at 17 K as the moderating and cooling medium. There are several technical challenges to overcome in the design of a robust system that will operate under such conditions, not least the 20 kW of deposited heat. These challenges and the associated design solutions will be detailed in this paper.

  18. Status of R&D on mitigating the effects of pressure waves for the Spallation Neutron Source mercury target

    Science.gov (United States)

    Riemer, Bernard W.; Wendel, Mark W.; Felde, David K.; Abdou, Ashraf A.; McClintock, David A.

    2012-12-01

    The Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory has been conducting R&D on mitigating the effects of pressure waves in mercury spallation targets since 2001. More precisely, cavitation damage of the target vessel caused by the short beam pulse threatens to limit its lifetime more severely than radiation damage as well as limit its ultimate power capacity - and hence its neutron intensity performance. The R&D program has moved from verification of the beam-induced damage phenomena to study of material and surface treatments for damage resistance to the current emphasis on gas injection techniques for damage mitigation. Two techniques are being worked on: injection of small dispersed gas bubbles that mitigate the pressure waves volumetrically; and protective gas walls that isolate the vessel from the damaging effects of collapsing cavitation bubbles. The latter has demonstrated good damage mitigation during in-beam testing with limited pulses, and adequate gas wall coverage at the beam entrance window has been demonstrated with the SNS mercury target flow configuration using a full scale mercury test loop. A question on the required area coverage remains which depends on results from SNS target post irradiation examination. The small gas bubble technique has been less effective during past in-beam tests but those results were with un-optimized and un-verified bubble populations. Another round of in-beam tests with small gas bubbles is planned for 2011. The first SNS target was removed from service in mid 2009 and samples were cut from two locations at the target's beam entrance window. Through-wall damage was observed at the innermost mercury vessel wall (not a containment wall). The damage pattern suggested correlation with the local mercury flow condition which is nearly stagnant at the peak damage location. Detailed post irradiation examination of the samples is under way that will assess the erosion and measure irradiation-induced changes

  19. Status of R and D on mitigating the effects of pressure waves for the Spallation Neutron Source mercury target

    Energy Technology Data Exchange (ETDEWEB)

    Riemer, Bernard W., E-mail: riemerbw@ornl.gov [Spallation Neutron Source/Oak Ride National Laboratory, P.O. Box 2008, Bldg. 8600, MS 6466, Oak Ridge, TN 37831 (United States); Wendel, Mark W.; Felde, David K.; Abdou, Ashraf A.; McClintock, David A. [Spallation Neutron Source/Oak Ride National Laboratory, P.O. Box 2008, Bldg. 8600, MS 6466, Oak Ridge, TN 37831 (United States)

    2012-12-15

    The Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory has been conducting R and D on mitigating the effects of pressure waves in mercury spallation targets since 2001. More precisely, cavitation damage of the target vessel caused by the short beam pulse threatens to limit its lifetime more severely than radiation damage as well as limit its ultimate power capacity - and hence its neutron intensity performance. The R and D program has moved from verification of the beam-induced damage phenomena to study of material and surface treatments for damage resistance to the current emphasis on gas injection techniques for damage mitigation. Two techniques are being worked on: injection of small dispersed gas bubbles that mitigate the pressure waves volumetrically; and protective gas walls that isolate the vessel from the damaging effects of collapsing cavitation bubbles. The latter has demonstrated good damage mitigation during in-beam testing with limited pulses, and adequate gas wall coverage at the beam entrance window has been demonstrated with the SNS mercury target flow configuration using a full scale mercury test loop. A question on the required area coverage remains which depends on results from SNS target post irradiation examination. The small gas bubble technique has been less effective during past in-beam tests but those results were with un-optimized and un-verified bubble populations. Another round of in-beam tests with small gas bubbles is planned for 2011. The first SNS target was removed from service in mid 2009 and samples were cut from two locations at the target's beam entrance window. Through-wall damage was observed at the innermost mercury vessel wall (not a containment wall). The damage pattern suggested correlation with the local mercury flow condition which is nearly stagnant at the peak damage location. Detailed post irradiation examination of the samples is under way that will assess the erosion and measure irradiation

  20. Status of R&D on Mitigating the Effects of Pressure Waves for the Spallation Neutron Source Mercury Target

    Energy Technology Data Exchange (ETDEWEB)

    Riemer, Bernie [ORNL; Wendel, Mark W [ORNL; Felde, David K [ORNL; Abdou, Ashraf A [ORNL; McClintock, David A [ORNL

    2012-01-01

    The Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory has been conducting R&D on mitigating the effects of pressure waves in mercury spallation targets since 2001. More precisely, cavitation damage of the target vessel caused by the short beam pulse threatens to limit its lifetime more severely than radiation damage as well as limit its ultimate power capacity and hence its neutron intensity performance. The R&D program has moved from verification of the beam-induced damage phenomena to study of material and surface treatments for damage resistance to the current emphasis on gas injection techniques for damage mitigation. Two techniques are being worked on: injection of small dispersed gas bubbles that mitigate the pressure waves volumetrically; and protective gas walls that isolate the vessel from the damaging effects of collapsing cavitation bubbles. The latter has demonstrated good damage mitigation during in-beam testing with limited pulses, and adequate gas wall coverage at the beam entrance window has been demonstrated with the SNS mercury target flow configuration using a full scale mercury test loop. A question on the required area coverage remains which depends on results from SNS target post irradiation examination. The small gas bubble technique has been less effective during past in-beam tests but those results were with un-optimized and un-verified bubble populations. Another round of in-beam tests with small gas bubbles is planned for 2011. The first SNS target was removed from service in mid 2009 and samples were cut from two locations at the target s beam entrance window. Through-wall damage was observed at the innermost mercury vessel wall (not a containment wall). The damage pattern suggested correlation with the local mercury flow condition which is nearly stagnant at the peak damage location. Detailed post irradiation examination of the samples is under way that will assess the erosion and measure irradiation-induced changes

  1. Spallation Fragment Investigation on Nb, Au and Pb by Using Many Stage Dynamical Model

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The formation cross section of the nuclides production of proton-induced nuclear reactions withintermediate energy is of importance for a variety of applications. For instance, the mass and chargedistribution of residual products produced in the spallation reactions needs to be studied, because it canprovide useful information for the disposal of nuclear waste and residual radioactivity generated by thespallation neutron target system. At present work, we developed the many stage dynamical model

  2. Process technology and effects of spallation products: Circuit components, maintenance, and handling

    Energy Technology Data Exchange (ETDEWEB)

    Sigg, B.; Haines, S.J.; Dressler, R.; McManamy, T.

    1996-06-01

    Working Session D included an assessment of the status of the technology and components required to: (1) remove impurities from the liquid metal (mercury or Pb-Bi) target flow loop including the effects of spallation products, (2) provide the flow parameters necessary for target operations, and (3) maintain the target system. A series of brief presentations were made to focus the discussion on these issues. The subjects of these presentations, and presenters were: (1) Spallation products and solubilities - R. Dressler; (2) Spallation products for Pb-Bi - Y. Orlov; (3) Clean/up/impurity removal components - B. Sigg; (4) {open_quotes}Road-Map{close_quotes} and remote handling needs - T. McManamy; (5) Remote handling issues and development - M. Holding. The overall conclusion of this session was that, with the exception of (i) spallation product related processing issues, (ii) helium injection and clean-up, and (iii) specialized remote handling equipment, the technology for all other circuit components (excluding the target itself) exists. Operating systems at the Institute of Physics in Riga, Latvia (O. Lielausis) and at Ben-Gurion University in Beer Shiva, Israel (S. Lesin) have demonstrated that other liquid metal circuit components including pumps, heat exchangers, valves, seals, and piping are readily available and have been reliably used for many years. In the three areas listed above, the designs and analysis are not judged to be mature enough to determine whether and what types of technology development are required. Further design and analysis of the liquid metal target system is therefore needed to define flow circuit processing and remote handling equipment requirements and thereby identify any development needs.

  3. Determination of spallation residues in thin target: toward an hybrid reactor lead target simulation

    Energy Technology Data Exchange (ETDEWEB)

    Audouin, L.; Tassan-Got, L.; Bernas, M.; Rejmund, F.; Stephan, C.; Taieb, J. [Paris-11 Univ., 91- Orsay (France). Inst. de Physique Nucleaire; Enqvist, T.; Armbruster, P.; Ricciardi, M.V.; Schmidt, K.H. [GSI, Planckstrasse 1, Darmstadt (Germany); Boudard, A.; Fernandez, B.; Legrain, R.; Leray, S.; Volant, C.; Wlazlo, W. [CEA Saclay, Dept. d' Astrophysique, de Physique des Particules, de Physique Nucleaire et de l' Instrumentation Associee, 91 - Gif sur Yvette (France); Benlliure, J.; Casajeros, E.; Pereira, J. [University of Santiago de Compostella (Spain); Czajkowski, S. [Centre d' Etudes Nucleaires de Bordeaux Gradignan, CENBG, CNRS-IN2P3, 33 - Gradignan (France)

    2001-07-01

    The production of spallation primary residual nuclei in thin target has been studied by measurement of isotopic yields distributions for several systems. Issues relevant for the design of accelerator-driven systems are presented. Monte-Carlo code abilities to reproduce data are studied in details; it is shown that calculations do not reproduce data in a satisfactory way. Future work orientations leading to an improvement of thin targets calculations and ultimately to a thick target simulation are discussed. (author)

  4. Coherent Scattering Investigations at the Spallation Neutron Source: a Snowmass White Paper

    Energy Technology Data Exchange (ETDEWEB)

    Akimov, D. [Moscow Engineering Physics Institute (MEPhI), Russia; Bernstein, A. [Lawrence Livermore National Laboratory (LLNL); BarbeauP., [Duke University; Barton, P. J. [Lawrence Berkeley National Laboratory (LBNL); Bolozdynya, A. [Moscow Engineering Physics Institute (MEPhI), Russia; Cabrera-Palmer, B. [Sandia National Laboratories (SNL); Cavanna, F. [Yale University; Cianciolo, Vince [ORNL; Collar, J. [University of Chicago, Enrico Fermi Institute; Cooper, R. J. [Indiana University; Dean, D. J. [Oak Ridge National Laboratory (ORNL); Efremenko, Yuri [University of Tennessee (UTK) and Oak Ridge National Laboratory (ORNL); Etenko, A. [Moscow Engineering Physics Institute (MEPhI), Russia; Fields, N. [University of Chicago, Enrico Fermi Institute; Foxe, M. [Pennsylvania State University, University Park, PA; Figueroa-Feliciano, E. [Massachusetts Institute of Technology (MIT); Fomin, N. [University of Tennessee, Knoxville (UTK); Gallmeier, F. [Oak Ridge National Laboratory (ORNL); Garishvili, I. [University of Tennessee, Knoxville (UTK); Gerling, M. [Sandia National Laboratories (SNL); Green, M. [University of North Carolina, Chapel Hill; Greene, Geoffrey [University of Tennessee, Knoxville (UTK); Hatzikoutelis, A. [University of Tennessee, Knoxville (UTK); Henning, Reyco [University of North Carolina, Chapel Hill; Hix, R. [University of Tennessee (UTK) and Oak Ridge National Laboratory (ORNL); Hogan, D. [University of California-Berkeley; Hornback, D. [University of Tennessee (UTK) and Oak Ridge National Laboratory (ORNL); Jovanovic, I. [Pennsylvania State University, University Park, PA; Hossbach, T. [Pacific Northwest National Laboratory (PNNL); Iverson, Erik B [ORNL; Klein, S. R. [Lawrence Berkeley National Laboratory (LBNL); Khromov, A. [Moscow Engineering Physics Institute (MEPhI), Russia; Link, J. [Virginia Polytechnic Institute and State University; Louis, W. [Los Alamos National Laboratory (LANL); Lu, W. [Oak Ridge National Laboratory (ORNL); Mauger, C. [Los Alamos National Laboratory (LANL); Marleau, P. [Sandia National Laboratories (SNL); Markoff, D. [North Carolina Central University, Durham; Martin, R. D. [University of South Dakota; Mueller, Paul Edward [ORNL; Newby, J. [Oak Ridge National Laboratory (ORNL); Orrell, John L. [Pacific Northwest National Laboratory (PNNL); O' Shaughnessy, C. [University of North Carolina, Chapel Hill; Penttila, Seppo [Oak Ridge National Laboratory (ORNL); Patton, K. [North Carolina State University, Raleigh; Poon, A. W. [Lawrence Berkeley National Laboratory (LBNL); Radford, David C [ORNL; Reyna, D. [Sandia National Laboratories (SNL); Ray, H. [University of Florida, Gainesville; Scholberg, K. [Duke University, North Carolina; Sosnovtsev, V. [Moscow Engineering Physics Institute (MEPhI), Russia; Tayloe, R. [Indiana University; Vetter, K. [Lawrence Berkeley National Laboratory (LBNL); Virtue, C. [Laurentian University, Canada; Wilkerson, J. [University of North Carolina, Chapel Hill; Yoo, J. [Fermi National Accelerator Laboratory (FNAL); Yu, Chang-Hong [ORNL

    2013-01-01

    The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory, Tennessee, provides an intense flux of neutrinos in the few tens-of-MeV range, with a sharply-pulsed timing structure that is beneficial for background rejection. In this white paper, we describe how the SNS source can be used for a measurement of coherent elastic neutrino-nucleus scattering (CENNS), and the physics reach of different phases of such an experimental program (CSI: Coherent Scattering Investigations at the SNS).

  5. Optimization by simulation of the coupling between a sub-critical reactor and its spallation source. Towards a pilot reactor; Optimisation par simulation du couplage entre un reacteur sous-critique et sa source de spallation. Application a un demonstrateur

    Energy Technology Data Exchange (ETDEWEB)

    Kerdraon, D

    2001-10-01

    Accelerator Driven Systems (ADS), based on a proton accelerator and a sub-critical core coupled with a spallation target, offer advantages in order to reduce the nuclear waste radiotoxicity before repository closure. Many studies carried out on the ADS should lead to the definition of an experimental plan which would federate the different works in progress. This thesis deals with the neutronic Monte Carlo simulations with the MCNPX code to optimize such a system in view of a pilot reactor building. First, we have recalled the main neutronic properties of an hybrid reactor. The concept of gas-cooled eXperimental Accelerator Driven System (XADS) chosen for our investigations comes from the preliminary studies done by the Framatome company. In order to transmute minor actinides, we have considered the time evolution of the main fuels which could be reasonably used for the demonstration phases. The neutronic parameters of the reactor, concerning minor actinide transmutation, are reported. Also, we have calculated the characteristic times and the transmutation rates in the case of {sup 99}Tc and {sup 129}I isotopes. We have identified some neutronic differences between an experimental and a power ADS according to the infinite multiplication coefficient, the shape factor and the level of flux to extend the demonstrator concept. We have proposed geometric solutions to keep the radial shape factor of a power ADS acceptable. In the last part, beyond the experimental XADS scope, we have examined the possible transition towards an uranium/thorium cycle based on Molten Salt Reactors using a power ADS in order to generate the required {sup 233}U proportion. (author)

  6. A new 2.5 MeV injector and beam test facility for the spallation neutron source

    Science.gov (United States)

    Welton, R. F.; Aleksandrov, A.; Han, B. X.; Kang, Y. W.; Middendorf, M. M.; Murray, S. N.; Piller, M.; Pennisi, T. R.; Peplov, V.; Saethre, R.; Santana, M.; Stinson, C.; Stockli, M. P.

    2017-08-01

    The U.S. Spallation Neutron Source (SNS) now operates with 1.2 MW of beam power on target with the near-term goal of delivering 1.4 MW and a longer-term goal of delivering >2 MW to support a planned second target station. Presently, H- beam pulses (50-60 mA, 1 ms, 60 Hz) from an RF-driven, Cs-enhanced, multi-cusp ion source are first accelerated to 2.5 MeV by a Radio Frequency Quadrupole (RFQ) accelerator, injected into a ˜1 GeV linac, compressed to research accelerator employing the original SNS RFQ. After validating the new RFQ with respect to energy, emittance and transmission, the initial applications of the BTF will be to conduct 6D beam dynamic studies, develop & demonstrate ion sources capable of meeting the current and future requirements of the SNS, and contribute to neutron moderator development. This report provides a facility update, description of the BTF ion source systems as well as a discussion of the first LEBT and RFQ beam current measurements performed at the BTF.

  7. Mechanism of spallation in platinum aluminide/electron beam physical vapor-deposited thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Gell, M.; Vaidyanathan, K.; Barber, B.; Cheng, J.; Jordan, E. [Univ. of Connecticut, Storrs, CT (United States)

    1999-02-01

    The spallation failure of a commercial thermal barrier coating (TBC), consisting of a single-crystal RENE N5 superalloy, a platinum aluminide (Pt-Al) bond coat, and an electron beam-deposited 7 wt pct yttria-stabilized zirconia ceramic layer (7YSZ), was studied following cyclic furnace testing. In the uncycled state and prior to deposition of the ceramic, the Pt-Al bond-coat surface contains a cellular network of ridges corresponding to the underlying bond-coat grain-boundary structure. With thermal cycling, the ridges and associated grain boundaries are the sites of preferential oxidation and cracking, which results in the formation of cavities that are partially filled with oxide. Using a fluorescent penetrant dye in conjunction with a direct-pull test, it is shown that, when specimens are cycled to about 80 pct of life, these grain-boundary regions show extensive debonding. The roles of oxidation and cyclic stress in localized grain boundary region spallation are discussed. The additional factors leading to large-scale TBC spallation are described.

  8. Heavy density liquid metal spallation target studies for Indian ADS programme

    Indian Academy of Sciences (India)

    P Sathamurthy; L M Gantayet; A K Ray

    2007-02-01

    Department of Atomic Energy, India has taken up the development of ADS in view of many attractive features like inherent safety, capability to transmute large quantities of nuclear waste, better utilization of thorium etc. A roadmap has been finalized for the development of ADS. One of the key components of the ADS is the spallation target. Considering the neutron yield, thermal-hydraulics and radiation damage issues, we are proposing to develop spallation target based on heavy density liquid metals like lead and lead-bismuth-eutectic (LBE). Both window and windowless target configurations are presently being studied. In view of the various advantages we are also studying liquid metal flow circulation based on gas lift mechanism. An R&D programme has been initiated to address various physics and technology issues of ADS target. Under this programme, mercury and LBE experimental facilities are presently being set up. Along with these facilities, computational tools related to spallation physics (FLUKA) and CFD are being developed, and the existing ones are utilized to design the entire target loop as well as sub-systems. In this presentation the details of these activities are presented.

  9. Experimental Study of the Phenomenology of Spallation Neutrons in a Large Lead Block

    CERN Multimedia

    Galvez Altamirano, J; Lopez, C; Perlado, J M; Perez-Navarro, A

    2002-01-01

    %PS211 %title \\\\ \\\\The purpose of PS211 is to determine how neutrons, produced by spallation inside a large Lead volume are slowed down by undergoing a very large number of scatterings, losing each time a small fraction ($\\sim$ 1\\%) of their kinetic energy. The focus is in determining the probability for a spallation neutron produced at an energy of several MeV or more, to survive capture on Lead resonances and to reach resonance energies of materials to be transmuted, such as 5.6 eV for $^{99}$Tc. This process, of Adiabatic Resonance Crossing, involves a subtle interplay between the capture resonances of the Lead medium and of selected impurities. This phenomenology of spallation neutrons in a large Lead volume, is the physics foundation of the Fast Energy Amplifier proposed by C. Rubbia, and could open up new possibilities in the incineration of long-lived nuclear waste such as Actinides or Fission Fragments (e.g. $^{99}$Tc, $^{129}$I, etc.).\\\\ \\\\334 tons of high purity Lead, installed in t7, are exposed to...

  10. Spallation Backgrounds in Super-Kamiokande Are Made in Muon-Induced Showers

    CERN Document Server

    Li, Shirley Weishi

    2015-01-01

    Crucial questions about solar and supernova neutrinos remain unanswered. Super-Kamiokande has the exposure needed for progress, but detector backgrounds are a limiting factor. A leading component is the beta decays of isotopes produced by cosmic-ray muons and their secondaries, which initiate nuclear spallation reactions. Cuts of events after and surrounding muon tracks reduce this spallation decay background by $\\simeq 90\\%$ (at a cost of $\\simeq 20\\%$ deadtime), but its rate at 6 -- 18 MeV is still dominant. A better way to cut this background was suggested in a Super-Kamiokande paper [Bays {\\it et al.}, Phys.~Rev.~D {\\bf 85}, 052007 (2012)] on a search for the diffuse supernova neutrino background. They found that spallation decays above 16 MeV were preceded near the same location by a peak in the apparent Cherenkov light profile from the muon; a more aggressive cut was applied to a limited section of the muon track, leading to decreased background without increased deadtime. We put their empirical discove...

  11. Safety techniques in the change of nuclear systems. Radiation protection at spallation neutron sources and transmutation facilities; Sicherheitstechnik im Wandel Nuklearer Systeme. Strahlenschutz bei Spallationsneutronenquellen und Transmutationsanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Nuenighoff, Kay

    2009-07-01

    To push the boundary towards higher neutron fluxes concepts based on spallation reactions have been discussed. Here neutrons are produced by bombarding a heavy metal target (e.g. mercury, tungsten, or tantalum) with high energetic protons. Up to now such facilities could not be realised because of the high power particle accelerators needed. Recent developments of the accelerator technology open the possibility of construction and operating proton accelerators in the MW region. This is demonstrated by construction and commissioning of two MW spallation neutron sources, namely SNS (Oak Ridge, Tennessee, USA) with a power of 1.4 MW and J-PARC (Japan) with 1 MW. The realisation of proton accelerators at this power level will open the way towards energy amplifiers, as proposed e.g. by Carlo Rubbia. Such a facility will not only produce electric power. Furthermore longliving radionuclides can be transmutated into shortlived or even stable nuclides by neutron induced nuclear reactions. A mitigation of the problem of nuclear waste disposal. The above discussed developments prove that accelerators are not only constructed for research, moreover application of these technology became state of the art. With the emergence of particle accelerators in the MW region, radiation protection is confronted with new kind of problems to be solved. Especially the higher kinetic energies of the primary beam particles requires modification and expansion of computer programs well known in nuclear engineering. In contrast to nuclear reactors with kinetic energies up to 2-3 MeV, in spallation reaction secondary particles up to the incident energy in the GeV region will be produced. Problems related to radiation protection have to be considered in an energy range three orders of magnitude higher than known from nuclear reactors. In this thesis existing computer codes are compared and validated with data from selected experiments. Questions concerning radiation protection covers a broad range

  12. Accelerator driven reactors, - the significance of the energy distribution of spallation neutrons on the neutron statistics

    Energy Technology Data Exchange (ETDEWEB)

    Fhager, V

    2000-01-01

    In order to make correct predictions of the second moment of statistical nuclear variables, such as the number of fissions and the number of thermalized neutrons, the dependence of the energy distribution of the source particles on their number should be considered. It has been pointed out recently that neglecting this number dependence in accelerator driven systems might result in bad estimates of the second moment, and this paper contains qualitative and quantitative estimates of the size of these efforts. We walk towards the requested results in two steps. First, models of the number dependent energy distributions of the neutrons that are ejected in the spallation reactions are constructed, both by simple assumptions and by extracting energy distributions of spallation neutrons from a high-energy particle transport code. Then, the second moment of nuclear variables in a sub-critical reactor, into which spallation neutrons are injected, is calculated. The results from second moment calculations using number dependent energy distributions for the source neutrons are compared to those where only the average energy distribution is used. Two physical models are employed to simulate the neutron transport in the reactor. One is analytical, treating only slowing down of neutrons by elastic scattering in the core material. For this model, equations are written down and solved for the second moment of thermalized neutrons that include the distribution of energy of the spallation neutrons. The other model utilizes Monte Carlo methods for tracking the source neutrons as they travel inside the reactor material. Fast and thermal fission reactions are considered, as well as neutron capture and elastic scattering, and the second moment of the number of fissions, the number of neutrons that leaked out of the system, etc. are calculated. Both models use a cylindrical core with a homogenous mixture of core material. Our results indicate that the number dependence of the energy

  13. Analytical calculations and Monte-Carlo simulations of a high-resolution backscattering spectrometer for the long wavelength target station at the Spallation neutron source

    Science.gov (United States)

    Bordallo, H. N.; Herwig, K. W.; Zsigmond, G.

    2002-09-01

    Using the Monte-Carlo simulation programs McStas and VITESS, we present the design principles of the proposed high-resolution inverse geometry spectrometer on the Spallation neutron source (SNS)—long wavelength target station (LWTS). LWTS will enable the combination of large energy and momentum transfer ranges with energy resolution. Indeed the resolution of this spectrometer lie between that routinely achieved by spin echo techniques and the design goal of the high-power target station (HPTS) backscattering spectrometer. This niche of energy resolution is interesting for the study of slow motions of large objects and we are led to the domain of large molecules—polymers and biological molecules.

  14. $^{206}$ Po sources for production and release studies relevant for high power spallation targets

    CERN Multimedia

    The knowledge of the evaporation behaviour of Po is of essential importance for several scientific and technological applications, like accelerator driven systems (ADS) or the LIEBE project at CERN-ISOLDE. Fundamental investigations on the experimental conditions for the formation of volatile Po species as well as on the chemical composition of the volatile compounds are necessary for a safe operation of such facilities. $^{206}$Po, a mainly $\\gamma$- ray-emitting Po isotope with a half-life of 8.8 d, is best suited for model studies, due to the lower radiation hazard compared to the longer-lived $\\alpha$-emitting isotopes $^{208-210}$Po as well as the easy-to-measure $\\gamma$-ray emission. We propose the production of $^{206}$Po samples in several matrices via the implantation of its precursor $^{210}$Fr into selected metal foils at CERN-ISOLDE. Using these samples, experiments will be carried out at PSI studying the volatilization of Po from different matrices under varying chemical conditions.

  15. European Spallation Source ESS. Spanish participation in the ESS Primary system design; Fuente Europea de Spallation ESS. Participacion espanola en el diseno del sistema primario de la ESS

    Energy Technology Data Exchange (ETDEWEB)

    Dominguez, M. T.; Albisu, F.

    2001-07-01

    Neutron scattering provides basic microscopic information on the structure and dynamics of materials which underpins our understanding of condensed matter in fields as diverse as biology, material science chemistry, earth sciences and physics. Europe is preeminent, in this field and the current proposal for a next generation neutron source, the European Spallation source (ESS), will ensure that neutron beams of the highest quality are available early next century to a broad spectrum of users from academia and industry. In the Large Facilities Report to the Commission of the European Community (CEC) in 1990, the Neutron Study Panel underlined the continuing need for neutron scattering and recognised that a major initiative was necessary to secure an effective on-going neutron science programme in Europe for the year 2000 and beyond. (Author)

  16. Monitoring method of neutron flux for the spallation target used in an accelerator driven sub-critical systems

    CERN Document Server

    Zhao, Qiang; Yang, Lei; Zhang, Xueying; Cui, Wenjuan; Chen, Zhiqiang; Xu, Hushan

    2015-01-01

    In this paper, we study the monitoring method of neutron flux for the spallation target used in an accelerator driven sub-critical (ADS) system, where the spallation target located vertically at the centre of a sub-critical core is bombarded vertically by the high-energy protons from an accelerator. First, by considering the characteristics in the spatial variation of neutron flux from the spallation target, we propose the following multi-point measurement technique, i.e. the spallation neutron flux should be measured at multiple vertical locations. To explain why the flux should be measured at multiple locations, we have studied the neutron production from tungsten target bombarded by a 250 MeV-proton beam with the Geant4-based Monte Carlo simulations. The simulation results have indicated that the neutron flux at the central location is up to three orders of magnitude higher than the flux at the lower locations. Secondly, we have developed an effective technique in order to measure the spallation neutron fl...

  17. Modelling of the spallation reaction: analysis and testing of nuclear models; Simulation de la spallation: analyse et test des modeles nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Toccoli, C

    2000-04-03

    The spallation reaction is considered as a 2-step process. First a very quick stage (10{sup -22}, 10{sup -29} s) which corresponds to the individual interaction between the incident projectile and nucleons, this interaction is followed by a series of nucleon-nucleon collisions (intranuclear cascade) during which fast particles are emitted, the nucleus is left in a strongly excited level. Secondly a slower stage (10{sup -18}, 10{sup -19} s) during which the nucleus is expected to de-excite completely. This de-excitation is performed by evaporation of light particles (n, p, d, t, {sup 3}He, {sup 4}He) or/and fission or/and fragmentation. The HETC code has been designed to simulate spallation reactions, this simulation is based on the 2-steps process and on several models of intranuclear cascades (Bertini model, Cugnon model, Helder Duarte model), the evaporation model relies on the statistical theory of Weiskopf-Ewing. The purpose of this work is to evaluate the ability of the HETC code to predict experimental results. A methodology about the comparison of relevant experimental data with results of calculation is presented and a preliminary estimation of the systematic error of the HETC code is proposed. The main problem of cascade models originates in the difficulty of simulating inelastic nucleon-nucleon collisions, the emission of pions is over-estimated and corresponding differential spectra are badly reproduced. The inaccuracy of cascade models has a great impact to determine the excited level of the nucleus at the end of the first step and indirectly on the distribution of final residual nuclei. The test of the evaporation model has shown that the emission of high energy light particles is under-estimated. (A.C.)

  18. Preequilibrium Emission of Light Fragments in Spallation Reactions

    CERN Document Server

    Kerby, Leslie M; Sierk, Arnold J

    2013-01-01

    The ability to describe production of light fragments (LF) is important for many applications, such as cosmic-ray-induced single event upsets (SEUs), radiation protection, and cancer therapy with proton and heavy-ion beams. The Cascade-Exciton Model (CEM) and the Los Alamos version of the Quark-Gluon String Model (LAQGSM) event generators in the LANL transport code MCNP6, describe quite well the spectra of fragments with sizes up to 4He across a broad range of target masses and incident energies (up to ~ 5 GeV for CEM and up to ~ 1 TeV/A for LAQGSM). However, they do not predict the high-energy tails of LF spectra heavier than 4He well. Most LF with energies above several tens of MeV are emitted during the precompound stage of a reaction. The current versions of our event generators do not account for precompound emission of LF larger than 4He. The aim of our work is to generalize the precompound model to include such processes, leading to increased predictive power of LF production. Extending the model in th...

  19. ALARA Review of the Spallation Neutron Source Accumulator Ring and Transfer Lines

    Energy Technology Data Exchange (ETDEWEB)

    Haire, M.J.

    2003-06-30

    The Spallation Neutron Source (SNS) is designed to meet the growing need for new tools that will deepen our understanding in materials science, life science, chemistry, fundamental and nuclear physics, earth and environmental sciences, and engineering sciences. The SNS is an accelerator-based neutron-scattering facility that when operational will produce an average beam power of 2 MW at a repetition rate of 60 Hz. The accelerator complex consists of the front-end systems, which will include an ion source; a 1-GeV full-energy linear accelerator; a single accumulator ring and its transfer lines; and a liquid mercury target. This report documents an as-low-as-reasonably-achievable (ALARA) review of the accumulator ring and transfer lines at their early design stage. An ALARA working group was formed and conducted a review of the SNS ring and transfer lines at the {approx}25% complete design stage to help ensure that ALARA principles are being incorporated into the design. The radiological aspects of the SNS design criteria were reviewed against regulatory requirements and ALARA principles. Proposed features and measures were then reviewed against the SNS design criteria. As part of the overall review, the working group reviewed the design manual; design drawings and process and instrumentation diagrams; the environment, safety, and health manual; and other related reports and literature. The group also talked with SNS design engineers to obtain explanations of pertinent subject matter. The ALARA group found that ALARA principles are indeed being incorporated into the early design stage. Radiation fields have been characterized, and shielding calculations have been performed. Radiological issues are being adequately addressed with regard to equipment selection, access control, confinement structure and ventilation, and contamination control. Radiation monitoring instrumentation for worker and environment protection are also being considered--a good practice at this

  20. First results of the new n-TOF spallation target commissioning

    Energy Technology Data Exchange (ETDEWEB)

    Berthoumieux, E.; Andriamonje, S.; Andrzejewski, J.; Audouin, L.; Becares, V.; Becvar, F.; Belloni, F.; Berthier, B.; Brugger, M.; Calviani, M.; Calvino, F.; Cano-Ott, D.; Carrapico, C.; Cennini, P.; Cerutti, F.; Chiaveri, E.; Chin, M.; Colonna, N.; Cortes, G.; Cortes-Giraldo, M.A.; Dillmann, I.; Domingo-Pardo, C.; Duran, I.; Fernandez-Ordonez, M.; Ferrari, A.; Ganesan, S.; Giubrone, G.; Gomez-Hornillos, M.B.; Goncalves, I.F.; Gonzalez-Romero, E.; Gramegna, F.; Guerrero, C.; Gunsing, F.; Harrisopulos, S.; Heil, M.; Ioannides, K.; Jericha, E.; Kadi, Y.; Kappeler, F.; Karadimos, D.; Krticka, M.; Lebbos, E.; Lederer, C.; Leeb, H.; Losito, R.; Lozano, M.; Marganiec, J.; Marrone, S.; Martinez, T.; Massimi, C.; Mastinu, P.F.; Meaze, M.; Mendoza, E.; Mengoni, A.; Milazzo, P.M.; Mosconi, M.; Nolte, R.; Paradela, C.; Pavlik, A.; Perkowski, J.; Plag, R.; Praena, J.; Quesada, J.M.; Rauscher, T.; Reifarth, R.; Roman, F.; Rubbia, C.; Sarmento, R.; Tagliente, G.; Tain, J.L.; Tarrio, D.; Tassan-Got, L.; Vannini, G.; Variale, V.; Vaz, P.; Ventura, A.; Vlachoudis, V.; Vlastou, R.; Vykydal, Z.; Wallner, A.; Weib, C.

    2009-07-01

    The Neutron Time of Flight facility n-TOF located at CERN started to take data in 2001. Due to an increase of radioactivity released in the cooling water the experiment was stopped by end of 2004. In 2008 a new spallation target has been installed. In 2009 the collaboration has performed the full commissioning of the facility, consisting in the determination of the fluence, the beam profile, and the energy resolution of the neutron beam. After a brief description of the new target assembly, very preliminary results concerning the shape of the neutron fluence and its absolute value will be given. Measurements of the neutron beam profile will also be shown. (authors)

  1. Opportunities for Neutrino Physics at the Spallation Neutron Source: A White Paper

    CERN Document Server

    Bolozdynya, A; Efremenko, Y; Garvey, G T; Gudkov, V; Hatzikoutelis, A; Hix, W R; Louis, W C; Link, J M; Markoff, D M; Mills, G B; Patton, K; Ray, H; Scholberg, K; Van de Water, R G; Virtue, C; White, D H; Yen, S; Yoo, J

    2012-01-01

    The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory, Tennessee, provides an intense flux of neutrinos in the few tens-of-MeV range, with a sharply-pulsed timing structure that is beneficial for background rejection. In this document, the product of a workshop at the SNS in May 2012, we describe this free, high-quality stopped-pion neutrino source and outline various physics that could be done using it. We describe without prioritization some specific experimental configurations that could address these physics topics.

  2. Mitigation and Prediction of Spallation of Oxide Scales on Ferritic Stainless Steel

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Y. S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stephens, Elizabeth V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Xu, Zhijie [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Xu, Wei [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Koeppel, Brian J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stevenson, Jeffry W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-02-04

    This report summarizes results from experimental and modeling studies performed by researchers at Pacific Northwest National Laboratory on behalf of the Solid-State Energy Conversion Alliance (SECA) Core Technology Program. The results indicate that application of physical surface modifications, such as surface blasting, prior to application of protective surface coatings can substantially increase oxide scale spallation resistance during long-term exposure to elevated temperatures (e.g., 800-850ºC). To better understand and predict the benefits of surface modification, an integrated modeling framework was developed and applied to the obtained experimental results.

  3. HYSPEC : A CRYSTAL TIME OF FLIGHT HYBRID SPECTROMETER FOR THE SPALLATION NEUTRON SOURCE.

    Energy Technology Data Exchange (ETDEWEB)

    SHAPIRO,S.M.; ZALIZNYAK,I.A.

    2002-12-30

    This document lays out a proposal by the Instrument Development Team (IDT) composed of scientists from leading Universities and National Laboratories to design and build a conceptually new high-flux inelastic neutron spectrometer at the pulsed Spallation Neutron Source (SNS) at Oak Ridge. This instrument is intended to supply users of the SNS and scientific community, of which the IDT is an integral part, with a platform for ground-breaking investigations of the low-energy atomic-scale dynamical properties of crystalline solids. It is also planned that the proposed instrument will be equipped with a polarization analysis capability, therefore becoming the first polarized beam inelastic spectrometer in the SNS instrument suite, and the first successful polarized beam inelastic instrument at a pulsed spallation source worldwide. The proposed instrument is designed primarily for inelastic and elastic neutron spectroscopy of single crystals. In fact, the most informative neutron scattering studies of the dynamical properties of solids nearly always require single crystal samples, and they are almost invariably flux-limited. In addition, in measurements with polarization analysis the available flux is reduced through selection of the particular neutron polarization, which puts even more stringent limits on the feasibility of a particular experiment. To date, these investigations have mostly been carried out on crystal spectrometers at high-flux reactors, which usually employ focusing Bragg optics to concentrate the neutron beam on a typically small sample. Construction at Oak Ridge of the high-luminosity spallation neutron source, which will provide intense pulsed neutron beams with time-averaged fluxes equal to those at medium-flux reactors, opens entirely new opportunities for single crystal neutron spectroscopy. Drawing upon experience acquired during decades of studies with both crystal and time-of-flight (TOF) spectrometers, the IDT has developed a conceptual

  4. Bond strength, bond stress and spallation mechanisms of thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Gell, M.; Krishnakumar, V.; McCarron, K.; Barber, B.; Sohn, Y.-H. [Connecticut Univ., Storrs, CT (United States). Dept. of Metall. and Mater. Eng.; Eric, J. [Connecticut Univ., Storrs, CT (United States). Dept. of Mechanical Engineering; Tolpygo, V.K.

    1999-11-01

    Five production thermal barrier coatings were thermally cycled between room temperature and 1121 C (2050 F) to determine relative spallation life. Bond strength measurements were made using a modified ASTM direct pull-test. Bond stress measurements were made in the thermally grown oxide using a laser photoluminescence technique. Bond strength and bond stress measurements were conducted on two electron beam physical vapor deposition coatings as a function of thermal cycling. Each coating showed characteristic values of as-coated strength and stress and changes in strength and stress with thermal cycling. These variations in strength and stress with thermal cycling are related to oxidation and micro-debonding effects. (orig.)

  5. Spallation Neutrons and Pressure SNAP DE-FG02-03ER46085 CLOSE-OUT MAY 2009

    Energy Technology Data Exchange (ETDEWEB)

    Parise, John B

    2009-05-22

    The purpose of the grant was to build a community of scientist and to draw upon their expertise to design and build the world's first dedicated high pressure beamline at a spallation source - the so called Spallation Neutron And Pressure (SNAP) beamline at the Spallation Neutron Source (SNS) at OAk Ridge NAtional LAboratory. . Key to this endeavor was an annual meeting attended by the instrument design team and the executive committee. The discussions at those meeting set an ambitious agenda for beamline design and construction and highlighted key science areas of interest for the community. This report documents in 4 appendices the deliberations at the annual SNAP meetings and the evolution of the beamline optics from concept to construction. The appendices also contain key science opportunities for extreme conditions research.

  6. Neutron time-of-flight spectrometer based on HIRFL for studies of spallation reactions related to ADS project

    Institute of Scientific and Technical Information of China (English)

    张苏雅拉吐; 罗飞; 陈志强; 韩瑞; 刘星泉; 林炜平; 刘建立; 石福栋; 任培培; 田国玉

    2015-01-01

    A Neutron Time-of-Flight (NTOF) spectrometer, based at the Heavy Ion Research Facility in Lanzhou (HIRFL) was developed for studies of neutron production of proton induced spallation reactions related to the ADS project. After the presentation of comparisons between calculated spallation neutron production double-differential cross sections and the available experimental data, a detailed description of the NTOF spectrometer is given. Test beam results show that the spectrometer works well and data analysis procedures are established. The comparisons of the test beam neutron spectra with those of GEANT4 simulations are presented.

  7. Proceedings of the workshop on ion source issues relevant to a pulsed spallation neutron source: Part 2 workshop presentations

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, L.; Leung, Ka-Ngo; Alonso, J. [eds.

    1994-10-01

    As part of the Lawrence Berkeley Laboratory Pulsed Spallation Source study, this Workshop was convened to address ion-source technology`s present status with respect to the next-generation Pulsed Spallation Source in the 1-5 MW range for the neutron scattering community. Considerations of Low Energy Beam Transport (LEBT) parameters and designs were included in the discussions throughout the Workshop. Ion-source requirements and actually-achieved performances were assessed, resulting in a determination of research and development requirements to bridge the gap. Part 1 of these Proceedings summarizes the Workshop; Part 2 contains viewgraphs of Workshop presentations.

  8. Quantum molecular dynamics approach to estimate spallation yield from + 208Pb reaction at 800 MeV

    Indian Academy of Sciences (India)

    P K Sarkar; Maitreyee Nandy

    2003-10-01

    The spallation yield of neutrons and other mass fragments produced in 800 MeV proton induced reaction on 208Pb have been calculated in the framework of quantum molecular dynamics (QMD) model. The energy spectra and angular distribution have been calculated. Also, multiplicity distributions of the emitted neutrons and kinetic energy carried away by them have been estimated and compared with the available experimental data. The agreement is satisfactory. A major contribution to the neutron emission comes from statistical decay of the fragments. For mass and charge distributions of spallation productsthe QMD process gives rise to target-like and projectile-like fragments only.

  9. Preliminary evaluation of cavitation-erosion resistance of Ti-alloys in mercury for the Spallation Neutron Source

    Science.gov (United States)

    Pawel, S. J.; Mansur, L. K.

    2010-03-01

    A number of Ti-based alloys in both the mill-annealed and 20% cold-worked conditions were subjected to sonication conditions in Hg using a vibratory horn to assess relative cavitation-erosion resistance. Weight loss as a function of exposure time decreased monotonically with increasing hardness for all alloys/conditions examined, with Ti-6Al-4V (Grade 5) and Ti-6Al-2Sn-4Zr-2Mo yielding the best resistance to cavitation-erosion as evidenced by low weight losses and little or no tendency to form pits on the exposed surface. Unalloyed Ti (Grade 4) and Ti-0.12Pd (Grade 7) exhibited greater weight losses by a factor of about two and about five, respectively, with Ti-0.12Pd particularly prone to pitting development. The mean erosion rates of the best two Ti-alloys examined were about a factor of three higher than identically tested 316LN stainless steel following a low temperature carburizing treatment, but this difference is considered minor given that the rate for both materials is very low/manageable and represents a through-thickness property for the Ti-alloys. A nitriding surface treatment was also evaluated as a potential method to further increase the cavitation-erosion resistance of these alloys in Hg, but the selected treatment proved largely ineffective as measured by rapid weight loss. Recommendations for further work to evaluate the efficacy of Ti-based alloys for use in high-powered targets for the Spallation Neutron Source are given.

  10. Opportunities for in-situ diffraction studies of advanced materials under extreme conditions at the US spallation neutron source

    Indian Academy of Sciences (India)

    J P Hodges

    2008-11-01

    The spallation neutron source (SNS) is an accelerator-based neutron source in Oak Ridge, Tennessee. Currently ramping up to 1.4 MW operating power, SNS will provide the most intense pulsed neutron beams in the world for scientific research and industrial development. Built by a partnership of six DOE laboratories SNS is operated as a user facility, open to scientists and engineers from universities, industry, and government laboratories in the United States and abroad. Eighteen dedicated beamline instruments are currently funded; four are completed and in operation, five are to be commissioned within a year and the others are at various stages of design and construction. All instruments at SNS have been designed to best in class and will provide unprecedented opportunities to explore the structure and dynamics of all materials. Amongst the funded instruments are a high-resolution very fast powder diffractometer (POWGEN3) optimized for parametric studies of materials under a wide range of conditions (, , and flowing gases), an ultrahigh-pressure diffractometer (SNAP) for materials under extreme conditions of pressure (up to 100 GPa) and temperature, an engineering materials diffractometer (VULCAN) for mapping strain, texture and fundamental aspects of materials behaviour of high performance materials under strain forces, a high flux disordered materials diffractometer (NOMAD) for liquids, glasses and disorder in crystalline materials, and a small angle scattering diffractometer (EQSANS) for investigating precipitates, crystallization, domains and nanoparticles in composite materials. ORNL/SNS is managed by UT-Battelle, LLC, for the U.S. Department of Energy under contract DE-AC05-00OR22725.

  11. Assessment of the neutron cross section database for mercury for the ORNL spallation source

    Energy Technology Data Exchange (ETDEWEB)

    Leal, L.C.; Spencer, R.R.; Ingersoll, D.T.; Gabriel, T.A. [Oak Ridge National Lab., TN (United States)

    1996-06-01

    Neutron source generation based on a high energy particle accelerator has been considered as an alternative to the canceled Advanced Neutron Source project at Oak Ridge National Laboratory. The proposed technique consists of a spallation neutron source in which neutrons are produced via the interaction of high-energy charged particles in a heavy metal target. Preliminary studies indicate that liquid mercury bombarded with GeV protons provides an excellent neutron source. Accordingly, a survey has been made of the available neutron cross-section data. Since it is expected that spectral modifiers, specifically moderators, will also be incorporated into the source design, the survey included thermal energy, resonance region, and high energy data. It was found that data of individual isotopes were almost non-existent and that the only evaluation found for the natural element had regions of missing data or discrepant data. Therefore, it appears that to achieve the desired degree of accuracy in the spallation source design it is necessary to re-evaluate the mercury database including making new measurements. During the presentation the currently available data will be presented and experiments proposed which can lead to design quality cross sections.

  12. Spallation radiation damage and dosimetry for accelerator transmutation of waste applications

    Energy Technology Data Exchange (ETDEWEB)

    Wechsler, M.S.; Lin, C. [North Carolina State Univ., Raleigh, NC (United States). Dept. of Nuclear Engineering; Ferguson, P.D. [Missouri Univ., Rolla, MO (United States). Dept. of Nuclear Engineering; Sommer, W.F. [Los Alamos National Lab., NM (United States)

    1993-10-01

    Proposals are currently being made for systems to treat radioactive waste based on the use of accelerator-driven neutron sources. A linear proton accelerator with energies as high as 1600 MeV and currents up to 250 ma are anticipated for the driver. The neutron fluxes may reach up to 10{sup 20} neutrons/m{sup 2}s as generated by the spallation reactions that occur when the protons strike target materials. Calculations are described to determine radiation fluxes and flux spectra inherent in such systems and to estimate likely radiation effects on system components. The calculations use LAHET, a Monte Carlo high-energy transport code, and MCNP, a generalized-geometry, coupled neutron-photon Monte Carlo transport code. Cross sections for displacement and helium production are presented for spallation neutrons of energies from 21 MeV to 1600 MeV for Inconel 718 (Ni plus 18.5, 18.5, 5.1, and 3 wt % of Cr, Fe, Nb, and Mo, respectively), an alloy that is used for the proton beam entry window in several accelerators. In addition, results for this alloy are presented for the primary knocked-on atom (PKA) spectrum and the transmutation yield for 1600 MeV incident neutrons.

  13. GEANT4 simulations of the n{sub T}OF spallation source and their benchmarking

    Energy Technology Data Exchange (ETDEWEB)

    Lo Meo, S. [Research Centre ' ' Ezio Clementel' ' , ENEA, Bologna (Italy); Section of Bologna, INFN, Bologna (Italy); Cortes-Giraldo, M.A.; Lerendegui-Marco, J.; Guerrero, C.; Quesada, J.M. [Universidad de Sevilla, Facultad de Fisica, Sevilla (Spain); Massimi, C.; Vannini, G. [Section of Bologna, INFN, Bologna (Italy); University of Bologna, Physics and Astronomy Dept. ' ' Alma Mater Studiorum' ' , Bologna (Italy); Barbagallo, M.; Colonna, N. [INFN, Section of Bari, Bari (Italy); Mancusi, D. [CEA-Saclay, DEN, DM2S, SERMA, LTSD, Gif-sur-Yvette CEDEX (France); Mingrone, F. [Section of Bologna, INFN, Bologna (Italy); Sabate-Gilarte, M. [Universidad de Sevilla, Facultad de Fisica, Sevilla (Spain); European Organization for Nuclear Research (CERN), Geneva (Switzerland); Vlachoudis, V. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Collaboration: The n_TOF Collaboration

    2015-12-15

    Neutron production and transport in the spallation target of the n{sub T}OF facility at CERN has been simulated with GEANT4. The results obtained with different models of high-energy nucleon-nucleus interaction have been compared with the measured characteristics of the neutron beam, in particular the flux and its dependence on neutron energy, measured in the first experimental area. The best agreement at present, within 20% for the absolute value of the flux, and within few percent for the energy dependence in the whole energy range from thermal to 1 GeV, is obtained with the INCL++ model coupled with the GEANT4 native de-excitation model. All other available models overestimate by a larger factor, of up to 70%, the n{sub T}OF neutron flux. The simulations are also able to accurately reproduce the neutron beam energy resolution function, which is essentially determined by the moderation time inside the target/moderator assembly. The results here reported provide confidence on the use of GEANT4 for simulations of spallation neutron sources. (orig.)

  14. Monte Carlo Modeling of Minor Actinide Burning in Fissile Spallation Targets

    Science.gov (United States)

    Malyshkin, Yury; Pshenichnov, Igor; Mishustin, Igor; Greiner, Walter

    2014-06-01

    Minor actinides (MA) present a harmful part of spent nuclear fuel due to their long half-lives and high radio-toxicity. Neutrons produced in spallation targets of Accelerator Driven Systems (ADS) can be used to transmute and burn MA. Non-fissile targets are commonly considered in ADS design. However, additional neutrons from fission reactions can be used in targets made of fissile materials. We developed a Geant4-based code MCADS (Monte Carlo model for Accelerator Driven Systems) for simulating neutron production and transport in different spallation targets. MCADS is suitable for calculating spatial distributions of neutron flux and energy deposition, neutron multiplication factors and other characteristics of produced neutrons and residual nuclei. Several modifications of the Geant4 source code described in this work were made in order to simulate targets containing MA. Results of MCADS simulations are reported for several cylindrical targets made of U+Am, Am or Am2O3 including more complicated design options with a neutron booster and a reflector. Estimations of Am burning rates are given for the considered cases.

  15. A neutron booster for spallation sources--application to accelerator driven systems and isotope production

    CERN Document Server

    Galy, J; Van Dam, H; Valko, J

    2002-01-01

    One can design a critical system with fissile material in the form of a thin layer on the inner surface of a cylindrical neutron moderator such as graphite or beryllium. Recently, we have investigated the properties of critical and near critical systems based on the use of thin actinide layers of uranium, plutonium and americium. The thickness of the required fissile layer depends on the type of fissile material, its concentration in the layer and on the geometrical arrangement, but is typically in the mu m-mm range. The resulting total mass of fissile material can be as low as 100 g. Thin fissile layers have a variety of applications in nuclear technology--for example in the design neutron amplifiers for medical applications and 'fast' islands in thermal reactors for waste incineration. In the present paper, we investigate the properties of a neutron booster unit for spallation sources and isotope production. In those applications a layer of fissile material surrounds the spallation source. Such a module cou...

  16. Surface Laser Scanning Measurements for the n_TOF spallation target

    CERN Document Server

    Vlachoudis, V; Cennini, P; Lebbos, E; Lettry, J

    2010-01-01

    The n_TOF spallation target is made of pure lead immersed into cooling water. The target was operating normally from 2001 until august 2004, when an increased transfer of radioactive products from the spallation target to the cooling circuit has been observed. The target was considered damaged by the safety commission (SC/RP), and an investigation campaign started to verify the actual status of the target. According to FLUKA and Ansys calculations the target was working in the elastoplastic regime of the lead material, therefore a deformation might be expected. The present paper describes a laser photographic method and the results of a possible such deformation. The target had a surface activity of the order of 20 mSv/h, therefore we were forced to perform the measurement from distance. The used method, is based on a linelaser and a high resolution digital camera for retrieving the 3D position of the surface of the lead target. Similar methods are used in the film industry and animation studios for scanning ...

  17. Study of the Production of Radioactive Isotopes through Cosmic Muon Spallation in KamLAND

    Energy Technology Data Exchange (ETDEWEB)

    KamLAND Collaboration; Abe, S.; Enomoto, S.; Furuno, K.; Gando, Y.; Ikeda, H.; Inoue, K.; Kibe, Y.; Kishimoto, Y.; Koga, M.; Minekawa, Y.; Mitsui, T.; Nakajima, K.; Nakajima, K.; Nakamura, K.; Nakamura, M.; Shimizu, I.; Shimizu, Y.; Shirai, J.; Suekane, F.; Suzuki, A.; Takemoto, Y.; Tamae, K.; Terashima, A.; Watanabe, H.; Yonezawa, E.; Yoshida, S.; Kozlov, A.; Murayama, H.; Busenitz, J.; Classen, T.; Grant, C.; Keefer, G.; Leonard, D. S.; McKee, D.; Piepke, A.; Banks, T. I.; Bloxham, T.; Detwiler, J. A.; Freedman, S. J.; Fujikawa, B. K.; Gray, F.; Guardincerri, E.; Hsu, L.; Ichimura, K.; Kadel, R.; Lendvai, C.; Luk, K.-B.; O' Donnell, T.; Steiner, H. M.; Winslow, L. A.; Dwyer, D. A.; Jillings, C.; Mauger, C.; McKeown, R. D.; Vogel, P.; Zhang, C.; Berger, B. E.; Lane, C. E.; Maricic, J.; Miletic, T.; Batygov, M.; Learned, J. G.; Matsuno, S.; Pakvasa, S.; Foster, J.; Horton-Smith, G. A.; Tang, A.; Dazeley, S.; Downum, K. E.; Gratta, G.; Tolich, K.; Bugg, W.; Efremenko, Y.; Kamyshkov, Y.; Perevozchikov, O.; Karwowski, H. J.; Markoff, D. M.; Tornow, W.; Heeger, K. M.; Piquemal, F.; Ricol, J.-S.; Decowski, M. P.

    2009-06-30

    Radioactive isotopes produced through cosmic muon spallation are a background for rare event detection in {nu} detectors, double-beta-decay experiments, and dark-matter searches. Understanding the nature of cosmogenic backgrounds is particularly important for future experiments aiming to determine the pep and CNO solar neutrino fluxes, for which the background is dominated by the spallation production of {sup 11}C. Data from the Kamioka Liquid scintillator Anti-Neutrino Detector (KamLAND) provides valuable information for better understanding these backgrounds, especially in liquid scintillator, and for checking estimates from current simulations based upon MUSIC, FLUKA, and Geant4. Using the time correlation between detected muons and neutron captures, the neutron production yield in the KamLAND liquid scintillator is measured to be (2.8 {+-} 0.3) x 10{sup -4} n/({mu} {center_dot} (g/cm{sup 2})). For other isotopes, the production yield is determined from the observed time correlation related to known isotope lifetimes. We find some yields are inconsistent with extrapolations based on an accelerator muon beam experiment.

  18. A drabkin energy filter for experiments at a spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Parizzi, A.A.; Klose, F. [Spallation Neutron Source, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Felcher, G.P. [Materials Science Division, Argonne National Laboratory, Argonne, IL (United States)

    2001-03-01

    We present a new approach for dynamic monochromatization of neutrons suitable for time-of-flight experiments at spallation neutron sources. The method requires polarized neutrons and is based on the Drabkin energy filter. In its initial application, this magnetic resonator device, consisting of a polarizer/analyzer system and a wavelength-dependent spin flipper, was proposed for extracting a narrow bandwidth from a broad bandwidth polarized neutron beam. At a spallation neutron source, wavelength is determined by time-of-flight (TOF) from the source to the detector. However, at each instant a spread of wavelengths is recorded due to the non-zero emission time-width of the source/moderator system. Particularly, high-intensity moderators for cold neutrons produce long 'tails' in the intensity/time distribution for all wavelengths, limiting the resolution of the experiments. The Drabkin energy filter can be used to cut the neutron tails for all wavelengths, by drifting the resonance condition in synchronization with the TOF. Calculations show that the method is viable, and that substantial resolution gains are obtainable by application to a TOF neutron reflectometer. (author)

  19. A Drabkin energy filter for experiments at a spallation neutron source.

    Energy Technology Data Exchange (ETDEWEB)

    Parizzi, A. A.; Felcher, G. P.; Klose, F.

    2000-11-21

    We present a new approach for dynamic monochromatization of neutrons suitable for time-of-flight experiments at spallation neutron sources. The method requires polarized neutrons and is based on the Drabkin energy filter. In its initial application, this magnetic resonator device, consisting of a polarizer/analyzer system and a wavelength-dependent spin flipper, was proposed for extracting a narrow bandwidth from a broad bandwidth polarized neutron beam. At a spallation neutron source, wavelength is determined by time-of-flight (TOF) from the source to the detector. However, at each instant a spread of wavelengths is recorded due to the non-zero emission time of the source/moderator system. Particularly, high-intensity moderators for cold neutrons produce long ''tails'' in the intensity/time distribution for all wavelengths, degrading the resolution of the experiments. The Drabkin energy filter can be used to cut the neutron tails for all wavelengths, by drifting the resonance condition in synchronization with the TOF. Calculations show that the method is viable, and that substantial resolution gains are obtained by application to a TOF neutron reflectometer.

  20. Validation of PHITS Spallation Models from the Perspective of the Shielding Design of Transmutation Experimental Facility

    Science.gov (United States)

    Iwamoto, Hiroki; Meigo, Shin-ichiro

    2017-09-01

    The impact of different spallation models implemented in the particle transport code PHITS on the shielding design of Transmutation Experimental Facility is investigated. For 400-MeV proton incident on a lead-bismuth eutectic target, an effective dose rate at the end of a thick radiation shield (3-m-thick iron and 3-m-thick concrete) calculated by the Liège intranuclear cascade (INC) model version 4.6 (INCL4.6) coupled with the GEMcode (INCL4.6/GEM) yields about twice as high as the Bertini INC model (Bertini/GEM). A comparison with experimental data for 500-MeV proton incident on a thick lead target suggest that the prediction accuracy of INCL4.6/GEM would be better than that of Bertini/GEM. In contrast, it is found that the dose rates in beam ducts in front of targets calculated by the INCL4.6/GEMare lower than those by the Bertini/GEM. Since both models underestimate the experimental results for neutron-production doubledifferential cross sections at 180° for 140-MeV proton incident on carbon, iron, and gold targets, it is concluded that it is necessary to allow a margin for uncertainty caused by the spallation models, which is a factor of two, in estimating the dose rate induced by neutron streaming through a beam duct.

  1. Validation of PHITS Spallation Models from the Perspective of the Shielding Design of Transmutation Experimental Facility

    Directory of Open Access Journals (Sweden)

    Iwamoto Hiroki

    2017-01-01

    Full Text Available The impact of different spallation models implemented in the particle transport code PHITS on the shielding design of Transmutation Experimental Facility is investigated. For 400-MeV proton incident on a lead-bismuth eutectic target, an effective dose rate at the end of a thick radiation shield (3-m-thick iron and 3-m-thick concrete calculated by the Liège intranuclear cascade (INC model version 4.6 (INCL4.6 coupled with the GEMcode (INCL4.6/GEM yields about twice as high as the Bertini INC model (Bertini/GEM. A comparison with experimental data for 500-MeV proton incident on a thick lead target suggest that the prediction accuracy of INCL4.6/GEM would be better than that of Bertini/GEM. In contrast, it is found that the dose rates in beam ducts in front of targets calculated by the INCL4.6/GEMare lower than those by the Bertini/GEM. Since both models underestimate the experimental results for neutron-production doubledifferential cross sections at 180◦ for 140-MeV proton incident on carbon, iron, and gold targets, it is concluded that it is necessary to allow a margin for uncertainty caused by the spallation models, which is a factor of two, in estimating the dose rate induced by neutron streaming through a beam duct.

  2. Towards the construction of the European spallation source – The Scandinavian experience

    Indian Academy of Sciences (India)

    C J Carlile; C Vettier; P Carlsson

    2008-11-01

    The possible realization of the European spallation source has been a long and winding story. However, thanks to the conjunction of a number of events it now looks highly probable that in 2008 there will indeed be a decision on the site and on a funding partnership of European countries who will together build and operate this long-pulse spallation neutron source. Currently there is a reference design comprising of a 632 m long proton accelerator which will deliver 2 ms pulses of protons to a liquid metal target with 22 instruments receiving thermal and cold neutron beams and providing unprecedented data rates. Lund is one of the two consortia competing to build the ESS – the ESS Scandinavia and a Hungarian–Spanish collaboration which is currently deciding on its preferred site. The Lund experience is one which highlights the many delicate steps which must be taken in order to get close to such decisions in a Europe of 30 plus nations. Of particular interest is the Energy Management Strategy which ESS Scandinavia would implement if Lund were to be the eventual chosen site. This will be set into the context of the political iniatives to mitigate the effects of global warming.

  3. Study of the spallation residues in the reaction Au (800 MeV/nucleon) + p; Etude des residus de spallation dans la reaction Au (800 MeV par nucleon) + p

    Energy Technology Data Exchange (ETDEWEB)

    Mustapha, Brahim [Inst. de Physique Nucleaire, Paris-11 Univ., 91 - Orsay (France)

    1999-09-09

    As a neutron source, the spallation reaction is of importance for different fields of research and for a possible hybrid reactor. The study of spallation residues, their cross sections and their energetic properties, is necessary for such applications and for a better understanding of this process. Several studies of spallation products were done using spectroscopic methods. Only radioactive nuclides were detected. Aiming at a more precise measurement, covering the whole range of spallation residues, this study was done using the reverse kinematics method. A liquid hydrogen target was irradiated by an 800 MeV/nucleon gold beam. The produced nuclei were detected in flight before any radioactive decay with about 10% precision. Independent cross section were then obtained. Velocity distributions were completely reconstructed. In their present forms, the theoretical calculations based upon the two-step model, 'intra-nuclear cascade' + 'evaporation', are unable to reproduce the whole set of experimental aspects. An inter-comparison using different INC/EVA combinations permitted to identify the more significant points in these calculations. The important behaviour of this codes were examined. Due to compensation effects between both steps, cascade and evaporation, this study did not lead to a definite conclusion. (author)

  4. Management of the radioactive waste of European Spallation Source within the Swedish waste disposal system

    Energy Technology Data Exchange (ETDEWEB)

    Ene, Daniela [European Spallation Source AB, ESS-AB (Sweden); Forsstroem, H. [Svensk Kaernbraenslehantering AB, SKB (Sweden)

    2014-07-01

    The European Spallation Source AB (ESS) is the European common effort in designing and building a next generation large-scale user facility for studies of the structure and dynamics of materials. The proposed schematic layout of the ESS facility is based on a linear driver (linac) directing the proton beam (5 MW of 2.5 GeV) of 2.8 ms long pulses with a 20 Hz on a tungsten target where neutrons are produced via spallation reactions. Further the neutrons will be moderated to thermal and sub-thermal energies in a couple of moderators placed around the target. The moderators feed 22 beam-lines guiding the neutrons to the scattering instruments, mainly for neutron scattering research, as has been previously mentioned. The ESS will generate specific types of radioactive waste. This waste should be handled and disposed of within the Swedish radioactive waste management system, which is owned and operated by Svensk Kaernbraenslehantering AB, (SKB). The main objectives of this work are: i) To estimate types and quantities of waste that the ESS project will generate at different stages: commission, operation, decommissioning; ii) To allocate the waste to specific disposal route; iii) To assess the disposal volumes needed and to ensure that the ESS waste may safely be accommodated within the Swedish disposal system, SKB The amounts of ESS waste and classifications were derived using: i) precise Monte Carlo calculations ii) scaling the activity from the operation experience of the existing spallation source installations for waste such it is difficult to predict level of activation or for components of the facility in stage of the pre-conceptual model. Associated waste treatment/conditioning options were further analyzed in order to define the waste type and packet descriptions in agreement with Swedish regulations and policy. The potential final disposal routes for high activated components were decided via the comparison of the activity levels of the isotopes inside the

  5. XT-ADS Windowless spallation target thermohydraulic design and experimental setup

    Energy Technology Data Exchange (ETDEWEB)

    Class, A.G., E-mail: andreas.class@kit.edu [KIT, Kaiserstrasse 12, D-76131 Karlsruhe (Germany); Angeli, D. [AAA, Advanced Accelerator Applications, 20 Rue Diesel, 06130 Saint-Genis-Poully (France); Batta, A. [KIT, Kaiserstrasse 12, D-76131 Karlsruhe (Germany); Dierckx, M. [SCK-CEN, Boeretang 200, B-2400 Mol (Belgium); Fellmoser, F. [KIT, Kaiserstrasse 12, D-76131 Karlsruhe (Germany); Moreau, V. [CRS4, Polaris Edificio 1, 09010 Pula, CA (Italy); Roelofs, F. [NRG Petten, Westerduinweg 3, P.O. Box 25, NL-1755 ZG Petten (Netherlands); Schuurmans, P.; Van Tichelen, K. [SCK-CEN, Boeretang 200, B-2400 Mol (Belgium); Wetzel, T. [KIT, Kaiserstrasse 12, D-76131 Karlsruhe (Germany)

    2011-08-31

    The objective of the European 6th framework Integrated Project (IP) EUROTRANS (EUROpean Research Programme for the TRANSmutation of High Level Nuclear Waste in an Accelerator Driven System) is to demonstrate the feasibility of transmutation of high level nuclear waste using subcritical Accelerator Driven Systems (ADS). The spallation target represents the most challenging new component in an ADS since it is the component coupling the accelerator and the nuclear core and is subjected to very high thermal load in a high radiation field. In this document the thermal hydraulic activities which led to reliable design rules for a windowless target are presented and the status of the heavy liquid metal target mock-up experiment at the KArlsruhe Liquid metal LAboratory (KALLA) are reported.

  6. Spallation Neutron Source Availability Top-Down Apportionment Using Characteristic Factors and Expert Opinion

    Energy Technology Data Exchange (ETDEWEB)

    Haire, M.J.; Schryver, J.C.

    1999-10-01

    Apportionment is the assignment of top-level requirements to lower tier elements of the overall facility. A method for apportioning overall facility availability requirements among systems and subsystems is presented. Characteristics that influence equipment reliability and maintainability are discussed. Experts, using engineering judgment, scored each characteristic for each system whose availability design goal is to be established. The Analytic Hierarchy Process (AHP) method is used to produce a set of weighted rankings for each characteristic for each alternative system. A mathematical model is derived which incorporates these weighting factors. The method imposes higher availability requirements on those systems in which an incremental increase in availability is easier to achieve, and lower availability requirements where greater availability is more difficult and costly. An example is given of applying this top-down apportionment methodology to the Spallation Neutron Source (SNS) facility.

  7. Acceptance scan technique for the drift tube linac of the spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, D. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)]. E-mail: jeond@ornl.gov; Stovall, J. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Takeda, H. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Nath, S. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Billen, J. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Young, L. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Kisselev, I. [Institute for Nuclear Research of RAS, Troitsk, Russia (Russian Federation); Shishlo, A. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Aleksandrov, A. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Assadi, S. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Chu, C.M. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Cousineau, S. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Danilov, V. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Galambos, J. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Henderson, S. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Kim, S. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Kravchuk, L. [Institute for Nuclear Research of RAS, Troitsk, Russia (Russian Federation); Tanke, E. [SNS Project, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)

    2007-01-01

    For high intensity proton accelerators, it is vital to reduce the machine activation by minimizing the beam loss from many sources. One of such sources is longitudinal mismatch. To minimize a potential mismatch, it is important to set accurately the rf set-point (rf field amplitude and phase) of a high-intensity linac such as the drift tube linac (DTL) of the spallation neutron source. A widely used technique called the acceptance scan was studied extensively and applied successfully to tune the DTL tanks since the initial commissioning. From the acceptance scan one can obtain the longitudinal beam profile at the entrance of each DTL tank. But except tank 1, acceptance scan alone cannot determine the incoming beam energy deviation, leading to small uncertainties in the rf set point.

  8. Numerical calculation of transverse coupling impedances: Comparison to Spallation Neutron Source extraction kicker measurements

    Directory of Open Access Journals (Sweden)

    B. Doliwa

    2007-10-01

    Full Text Available The study of beam dynamics and the localization of potential sources of instabilities are important tasks in the design of modern, high-intensity particle accelerators. In the case of synchrotrons and storage rings, coupling impedance data are needed to characterize the parasitic interaction of critical components with the beam. In this article we demonstrate the application of numerical field simulations to the computation of transverse kicker coupling impedances. Based on the 3D simulation results, a parametrized model is developed to incorporate the impedance of an arbitrary pulse-forming network attached to the kicker. Detailed comparisons of numerical results with twin-wire and direct measurements are discussed at the example of the Spallation Neutron Source extraction kicker.

  9. Comparisons of the simulation results using different codes for ADS spallation target

    CERN Document Server

    Yu Hong Wei; Shen Qing Biao; Wan Jun Sheng; Zhao Zhi Xiang

    2002-01-01

    The calculations to the standard thick target were made by using different codes. The simulation of the thick Pb target with length of 60 cm, diameter of 20 cm bombarded with 800, 1000, 1500 and 2000 MeV energetic proton beam was carried out. The yields and the spectra of emitted neutron were studied. The spallation target was simulated by SNSP, SHIELD, DCM/CEM (Dubna Cascade Model /Cascade Evaporation Mode) and LAHET codes. The Simulation Results were compared with experiments. The comparisons show good agreement between the experiments and the SNSP simulated leakage neutron yield. The SHIELD simulated leakage neutron spectra are in good agreement with the LAHET and the DCM/CEM simulated leakage neutron spectra

  10. MEANDER-LINE CURRENT STRUCTURE DEVELOPMENT FOR SPALLATION NEUTRON SOURCE FAST CHOPPER

    Energy Technology Data Exchange (ETDEWEB)

    S. KURRENOY; J. POWER

    2000-10-01

    A new current structure for the fast traveling-wave 2.5-MeV beam chopper in the front end of the Spallation Neutron Source (SNS) has been suggested in [1]. The structure is based on the meander-folded notched stripline with dielectric supports and separators. Its design has been optimized using electromagnetic 3-D modeling with the MAFIA code package to provide rise and fall times in the range of 1 to 2 ns. A full-length (50 cm) prototype has been manufactured, and its preliminary measurements showed a good agreement with the calculations. Detailed measurements results and their comparison with simulations are presented. The latest front-end design requires a shorter, 35-cm chopper with a higher pulse voltage. Its meander-line current structure, based on the same principles, has also been optimized with MAFIA.

  11. Development of a fast traveling-wave beam chopper for the National Spallation Neutron Source

    Energy Technology Data Exchange (ETDEWEB)

    Kurennoy, S.S.; Jason, A.J.; Krawczyk, F.L.; Power, J.

    1997-10-01

    High current and severe restrictions on beam losses, below 1 nA/m, in the designed linac for the National Spallation Neutron Source (NSNS) require clean and fast--with the rise time from 2% to 98% less than 2.5 ns to accommodate a 402.5-MHz beam structure--beam chopping in its front end, at the beam energy 2.5 MeV. The R and D program includes both modification of the existing LANSCE coax-plate chopper to reduce parasitic coupling between adjacent plates, and development of new traveling-wave deflecting structures, in particular, based on a meander line. Using analytical methods and three-dimensional time-domain computer simulations the authors study transient effects in such structures to choose an optimal chopper design.

  12. EXPERIENCE WITH COLLABORATIVE DEVELOPMENT FOR THE SPALLATION NEUTRON SOURCE FROM A PARTNER LAB PERSPECTIVE.

    Energy Technology Data Exchange (ETDEWEB)

    HOFF, L.T.

    2005-10-10

    Collaborative development and operation of large physics experiments is fairly common. Less common is the collaborative development or operation of accelerators. A current example of the latter is the Spallation Neutron Source (SNS). The SNS project was conceived as a collaborative effort between six DOE facilities. In the SNS case, the control system was also developed collaboratively. The SNS project has now moved beyond the collaborative development phase and into the phase where Oak Ridge National Lab (ORNL) is integrating contributions from collaborating ''partner labs'' and is beginning accelerator operations. In this paper, the author reflects on the benefits and drawbacks of the collaborative development of an accelerator control system as implemented for the SNS project from the perspective of a partner lab.

  13. Conceptual design of a cold methane moderator system for the European Spallation Source (ESS)

    CERN Document Server

    Barnert-Wiemer, H

    2002-01-01

    As part of the work for the target station of the planned European spallation source (ESS) the Central Department of Technology at the Forschungszentrum Juelich GmbH is also concerned with the moderators, particular attention being given to the development of cold methane moderators. This report discusses the technical feasibility of solid methane moderators. Methods to tailor the neutron output by adding absorption materials (decouplers or poisons) are not considered here, neither are composite moderators. Based on the given target-moderator-reflector assembly of the ESS project a concept for the ESS cold methane moderators has been developed and is being examined at the Forschungszentrum Juelich. According to this moderator concept the moderator is a fixed bed of small spheres, which makes moderator container filling homogeneous and reproducible. Since spheres form a defined packed bed, cooling of the moderator bed by H sub 2 is reliable. The process of filling the moderator container and of removing the pe...

  14. ACCELERATOR SYSTEMS MODIFICATIONS FOR A SECOND TARGET STATION AT THE OAK RIDGE SPALLATION NEUTRON SOURCE

    Energy Technology Data Exchange (ETDEWEB)

    Galambos, John D [ORNL; Kim, Sang-Ho [ORNL; Plum, Michael A [ORNL

    2014-01-01

    A second target station is planned for the Oak Ridge Spallation Neutron Source. The ion source will be upgraded to increase the peak current from 38 to 49 mA, additional superconducting RF cavities will be added to the linac to increase the H beam energy from 938 to 1300 MeV, and the accumulator ring will receive modifications to the injection and extraction systems to accommodate the higher beam energy. After pulse compression in the storage ring one sixth of the beam pulses (10 out of 60 Hz) will be diverted to the second target by kicker and septum magnets added to the existing Ring to Target Beam Transport (RTBT) line. No further modifications will be made to the RTBT so that when the kicker and septum magnets are turned off the original beam transport lattice will be unaffected. In this paper we will discuss these and other planned modifications and upgrades to the accelerator facility.

  15. Experiment Automation with a Robot Arm using the Liquids Reflectometer Instrument at the Spallation Neutron Source

    Energy Technology Data Exchange (ETDEWEB)

    Zolnierczuk, Piotr A [ORNL; Vacaliuc, Bogdan [ORNL; Sundaram, Madhan [ORNL; Parizzi, Andre A [ORNL; Halbert, Candice E [ORNL; Hoffmann, Michael C [ORNL; Greene, Gayle C [ORNL; Browning, Jim [ORNL; Ankner, John Francis [ORNL

    2013-01-01

    The Liquids Reflectometer instrument installed at the Spallation Neutron Source (SNS) enables observations of chemical kinetics, solid-state reactions and phase-transitions of thin film materials at both solid and liquid surfaces. Effective measurement of these behaviors requires each sample to be calibrated dynamically using the neutron beam and the data acquisition system in a feedback loop. Since the SNS is an intense neutron source, the time needed to perform the measurement can be the same as the alignment process, leading to a labor-intensive operation that is exhausting to users. An update to the instrument control system, completed in March 2013, implemented the key features of automated sample alignment and robot-driven sample management, allowing for unattended operation over extended periods, lasting as long as 20 hours. We present a case study of the effort, detailing the mechanical, electrical and software modifications that were made as well as the lessons learned during the integration, verification and testing process.

  16. The Design Performance of the Integrated Spallation Neutron Source Vacuum Control System

    CERN Document Server

    Tang, Johnny Y; Ladd, Peter; Williams, Derrick

    2005-01-01

    The Spallation Neutron Source vacuum control systems have been developed within a collaboration of Lawrence Berkeley National Laboratory(LBNL), Los Alamos National Laboratory(LANL), Thomas Jefferson National Accelerator Facility(TJNAF), and Brookhaven National Laboratory(BNL). Each participating lab is responsible for a different section of the machine. Although a great deal of effort has been made to standardize vacuum instrumentation components and the global control system interfaces, the varied requirements of the different sections of the machine made horizontal integration of the individual vacuum control systems both interesting and challenging. To support commissioning, the SNS control system team and the vacuum group developed a set of test strategies and the interlock schemes that allowed horizontal vacuum system integration to be effectively achieved. The design of the vacuum control interlock scheme developed will be presented together with the results of performance measurements made on these sch...

  17. Simulation of H- ion source extraction systems for the Spallation Neutron Source with Ion Beam Simulator.

    Science.gov (United States)

    Kalvas, T; Welton, R F; Tarvainen, O; Han, B X; Stockli, M P

    2012-02-01

    A three-dimensional ion optical code IBSimu, which is being developed at the University of Jyväskylä, features positive and negative ion plasma extraction models and self-consistent space charge calculation. The code has been utilized for modeling the existing extraction system of the H(-) ion source of the Spallation Neutron Source. Simulation results are in good agreement with experimental data. A high-current extraction system with downstream electron dumping at intermediate energy has been designed. According to the simulations it provides lower emittance compared to the baseline system at H(-) currents exceeding 40 mA. A magnetic low energy beam transport section consisting of two solenoids has been designed to transport the beam from the alternative electrostatic extraction systems to the radio frequency quadrupole.

  18. Simulation of H- ion source extraction systems for the Spallation Neutron Source with Ion Beam Simulatora)

    Science.gov (United States)

    Kalvas, T.; Welton, R. F.; Tarvainen, O.; Han, B. X.; Stockli, M. P.

    2012-02-01

    A three-dimensional ion optical code IBSimu, which is being developed at the University of Jyväskylä, features positive and negative ion plasma extraction models and self-consistent space charge calculation. The code has been utilized for modeling the existing extraction system of the H- ion source of the Spallation Neutron Source. Simulation results are in good agreement with experimental data. A high-current extraction system with downstream electron dumping at intermediate energy has been designed. According to the simulations it provides lower emittance compared to the baseline system at H- currents exceeding 40 mA. A magnetic low energy beam transport section consisting of two solenoids has been designed to transport the beam from the alternative electrostatic extraction systems to the radio frequency quadrupole.

  19. Geant4 simulations of the neutron production and transport in the n_TOF spallation target

    Science.gov (United States)

    Lerendegui-Marco, J.; Cortés-Giraldo, M. A.; Guerrero, C.; Quesada, J. M.

    2016-11-01

    The neutron production and transport in the spallation target of the n_TOF facility at CERN has been simulated with Geant4. The results obtained with the different hadronic Physics Lists provided by Geant4 have been compared with the experimental neutron flux in n_TOF-EAR1. The best overall agreement in both the absolute value and the energy dependence of the flux from thermal to 1GeV, is obtained with the INCL++ model coupled with the Fritiof Model(FTFP). This Physics List has been thus used to simulate and study the main features of the new n_TOF-EAR2 beam line, currently in its commissioning phase.

  20. Design of the low energy beam transport line for the China spallation neutron source

    Institute of Scientific and Technical Information of China (English)

    LI Jin-Hai; OUYANG Hua-Fu; FU Shi-Nian; ZHANG Sua-Shun; HE Wei

    2008-01-01

    The design of the China Spallation Neutron Source (CSNS) low-energy beam transport (LEBT) line, which locates between the ion source and the radio-frequency quadrupole (RFQ), has been completed with the TRACE3D code. The design aims at perfect matching, primary chopping, a small emittance growth and sufficient space for beam diagnostics. The line consists of three solenoids, three vacuum chambers, two steering magnets and a pre-chopper. The total length of LEBT is about 1.74 m. This LEBT is designed to transfer 20 mA of H-pulsed beam from the ion source to the RFQ. An induction cavity is adopted as the pre-chopper.The electrostatic octupole steerer is discussed as a candidate. A four-quadrant aperture for beam scraping and beam position monitoring is designed.

  1. Crossover from a fission-evaporation scenario towards multifragmentation in spallation reactions

    CERN Document Server

    Napolitani, P

    2006-01-01

    Mostly for the purpose of applications for the energy and the environment and for the design of sources of neutrons or exotic nuclides, intense research has been dedicated to spallation, induced by protons or light projectiles at incident energies of around 1 GeV. In this energy range, while multifragmentation has still a minor share in the total reaction cross section, it was observed to have, together with fission, a prominent role in the production and the kinematics of intermediate-mass fragments, so as to condition the whole production of light and heavy nuclides. The experimental observables we dispose of attribute rather elusive properties to the intermediate-mass fragments and do not allow to classify them within one exclusive picture which is either multifragmentation or fission. Indeed, these two decay mechanisms, driven by different kinds of instabilities, exhibit behaviours which are closely comparable. High-resolution measurements of the reaction kinematics trace the way for probing finer feature...

  2. VSI@ESS: Case study for a vibrational spectroscopy instrument at the european spallation source

    Science.gov (United States)

    Zoppi, Marco; Fedrigo, Anna; Celli, Milva; Colognesi, Daniele

    2015-01-01

    Neutron Vibrational Spectroscopy is a well-established experimental technique where elementary excitations at relatively high frequency are detected via inelastic neutron scattering. This technique attracts a high interest in a large fraction of the scientific community in the fields of chemistry, materials science, physics, and biology, since one of its main applications exploits the large incoherent scattering cross section of the proton with respect to all the other elements, whose dynamics can be spectroscopically detected, even if dissolved in very low concentration in materials composed of much heavier atoms. We have proposed a feasibility study for a Vibrational Spectroscopy Instrument (VSI) at the European Spallation Source ESS. Here, we will summarize the preliminary design calculations and the corresponding McStas simulation results for a possible ToF, Inverted Geometry, VSI beamline.

  3. VSI@ESS: Case study for a vibrational spectroscopy instrument at the european spallation source

    Directory of Open Access Journals (Sweden)

    Zoppi Marco

    2015-01-01

    Full Text Available Neutron Vibrational Spectroscopy is a well-established experimental technique where elementary excitations at relatively high frequency are detected via inelastic neutron scattering. This technique attracts a high interest in a large fraction of the scientific community in the fields of chemistry, materials science, physics, and biology, since one of its main applications exploits the large incoherent scattering cross section of the proton with respect to all the other elements, whose dynamics can be spectroscopically detected, even if dissolved in very low concentration in materials composed of much heavier atoms. We have proposed a feasibility study for a Vibrational Spectroscopy Instrument (VSI at the European Spallation Source ESS. Here, we will summarize the preliminary design calculations and the corresponding McStas simulation results for a possible ToF, Inverted Geometry, VSI beamline.

  4. Simulations towards optimization of a neutron/anti-neutron oscillation experiment at the European Spallation Source

    Science.gov (United States)

    Frost, Matthew; Kamyshkov, Yuri; Castellanos, Luis; Klinkby, Esben; US NNbar Collaboration

    2015-04-01

    The observation of Neutron/Anti-neutron oscillation would prove the existence of Baryon Number Violation (BNV), and thus an explanation for the dominance of matter over anti-matter in the universe. The latest experiments have shown the oscillation time to be greater than 8.6 x 107 seconds, whereas current theoretical predictions suggest times on the order of 108 to 109 seconds. A neutron oscillation experiment proposed at the European Spallation Source (ESS) would provide sensitivity of more than 1000 times previous experiments performed, thus providing a result well-suited to confirm or deny current theory. A conceptual design of the proposed experiment will be presented, as well as the optimization of key experiment components using Monte-Carlo simulation methods, including the McStas neutron ray-trace simulation package. This work is supported by the Organized Research Units Program funded by The University of Tennessee, Knoxville Office of Research and Engagement.

  5. Low-Level RF Control of Spallation Neutron Source: System and Characterization

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Hengjie [ORNL

    2005-01-01

    The low-level RF control system currently commissioned throughout the Spallation Neutron Source (SNS) LINAC evolved from three design iterations over one year intensive research and development. Its digital hardware implementation is efficient, and has succeeded in achieving a minimum latency of less than 150 ns which is the key for accomplishing an all digital feedback control for the full bandwidth. The control bandwidth is analyzed in frequency domain and characterized by testing its transient response. The hardware implementation also includes the provision of a time-shared input channel for a superior phase differential measurement between the cavity field and the reference. A companion co-simulation system for the digital hardware was developed to ensure a reliable long-term supportability. A large effort has also been made in the operation software development for the practical issues such as the process automations, cavity filling, beam loading compensation, and the cavity mechanical resonance suppression.

  6. THE COMMISSIONING PLAN FOR THE SPALLATION NEUTRON SOURCE RING AND TRANSPORT LINES.

    Energy Technology Data Exchange (ETDEWEB)

    RAPARIA,D.BLASKIEWICZ,M.LEE,Y.Y.WEI,J.ET AL.

    2004-03-10

    The Spallation Neutron Source (SNS) accelerator systems will provide a 1 GeV, 1.44 MW proton beam to a liquid mercury target for neutron production. In order to satisfy the accelerator systems' portion of the Critical Decision 4 (CD-4) commissioning goal (which marks the completion of the construction phase of the project), a beam pulse with intensity greater than 1 x 10{sup 13} protons must be accumulated in the ring, extracted in a single turn and delivered to the target. A commissioning plan has been formulated for bringing into operation and establishing nominal operating conditions for the various ring and transport line subsystems as well as for establishing beam conditions and parameters which meet the commissioning goal.

  7. A Spallation Model for 44Ti production in Core Collapse Supernovae

    CERN Document Server

    Ouyed, Amir; Leahy, Denis; Jaikumar, Prashanth

    2012-01-01

    Current cc-SN models predict overproduction of 44Ti compared to observations. We present a model for an alternative channel where a cc-SN explosion is followed by a neutron star detonation (Quark Nova or QN), resulting in a spallation reaction of SN ejecta that produces 44Ti. We can achieve a 44Ti production of ~ 10^-4 Msun with our model under the right time delay between the QN and the SN. Our model also produces unique signals not found in standard, cc-SN nucleosynthesis models. Some of these unique signals include a significantly large production of 7Be and 22Na. We discuss some of these signals by analyzing the late time light curve and gamma spectroscopy of our model.

  8. EXPERIENCE WITH COLLABORATIVE DEVELOPMENT FOR THE SPALLATION NEUTRON SOURCE FROM A PARTNER LAB PERSPECTIVE.

    Energy Technology Data Exchange (ETDEWEB)

    HOFF, L.T.

    2005-10-10

    Collaborative development and operation of large physics experiments is fairly common. Less common is the collaborative development or operation of accelerators. A current example of the latter is the Spallation Neutron Source (SNS). The SNS project was conceived as a collaborative effort between six DOE facilities. In the SNS case, the control system was also developed collaboratively. The SNS project has now moved beyond the collaborative development phase and into the phase where Oak Ridge National Lab (ORNL) is integrating contributions from collaborating ''partner labs'' and is beginning accelerator operations. In this paper, the author reflects on the benefits and drawbacks of the collaborative development of an accelerator control system as implemented for the SNS project from the perspective of a partner lab.

  9. Transmutation of $^{239}$Pu and Other Nuclides Using Spallation Neutrons Produced by Relativistic Protons Reacting with Massive U- and Pb-Targets

    CERN Document Server

    Adam, J; Bamblevski, V P; Barabanov, M Yu; Bradnova, V; Chaloun, P; Hella, K M; Kalinnikov, V G; Krivopustov, M I; Kulakov, B A; Perelygin, V P; Pronskikh, V S; Pavliouk, A V; Solnyshkin, A A; Sosnin, A N; Stegailov, V I; Tsoupko-Sitnikov, V M; Zaverioukha, O S; Adloff, J C; Debeauvais, M; Brandt, R; Langrock, E J; Vater, P; Van, J S; Westmeier, W; Dwivedi, K K; Guo Shi Lun; Li Li Qiang; Hashemi-Nezhad, S R; Kievets, M K; Lomonosova, E M; Zhuk, I V; Modolo, G; Odoj, R; Zamani-Valassiadou, M

    2001-01-01

    Experimental studies on the transmutation of some long-lived radioactive waste nuclei, such as ^{129}I, ^{237}Np, and ^{239}Pu, as well as on natural uranium and lanthanum (all of them used as sensors) were carried out at the Synchrophasotron of the Laboratory for High Energies (JINR, Dubna). Spallation neutrons were produced by relativistic protons with energies in the range of 0.5 GeV\\le E(p)\\le 1.5 GeV interacting with 20 cm long uranium or lead target stacks. The targets were surrounded by 6 cm paraffin moderators. The radioactive sensors mentioned above were positioned on the outside surface of the moderator and contained typically approximately 0.5 up to 1 gram of long-lived isotopes. The highly radioactive targets were produced perfectly well-sealed in aluminum containers by the Institute of Physics and Power Engineering, Obninsk, Russia. From the experimentally observed transmutation rates one can easily extrapolate, that in a subcritical nuclear power assembly (or "energy amplifier") using a 10 mA pr...

  10. Jet formation in spallation of metal film from substrate under action of femtosecond laser pulse

    Energy Technology Data Exchange (ETDEWEB)

    Inogamov, N. A., E-mail: nailinogamov@googlemail.com [Russian Academy of Sciences, Landau Institute for Theoretical Physics (Russian Federation); Zhakhovskii, V. V. [Dukhov All-Russia Research Institute of Automatics (Russian Federation); Khokhlov, V. A. [Russian Academy of Sciences, Landau Institute for Theoretical Physics (Russian Federation)

    2015-01-15

    It is well known that during ablation by an ultrashort laser pulse, the main contribution to ablation of the substance is determined not by evaporation, but by the thermomechanical spallation of the substance. For identical metals and pulse parameters, the type of spallation is determined by film thickness d{sub f}. An important gauge is metal heating depth d{sub T} at the two-temperature stage, at which electron temperature is higher than ion temperature. We compare cases with d{sub f} < d{sub T} (thin film) and d{sub f} ≫ d{sub T} (bulk target). Radius R{sub L} of the spot of heating by an optical laser is the next (after d{sub f}) important geometrical parameter. The morphology of film bulging in cases where d{sub f} < d{sub T} on the substrate (blistering) changes upon a change in radius R{sub L} in the range from diffraction limit R{sub L} ∼ λ to high values of R{sub L} ≫ λ, where λ ∼ 1 μm is the wavelength of optical laser radiation. When d{sub f} < d{sub T}, R{sub L} ∼ λ, and F{sub abs} > F{sub m}, gold film deposited on the glass target acquires a cupola-shaped blister with a miniature frozen nanojet in the form of a tip on the circular top of the cupola (F{sub abs} and F{sub m} are the absorbed energy and the melting threshold of the film per unit surface area of the film). A new physical mechanism leading to the formation of the nanojet is proposed.

  11. Disentangling xenon components in Nakhla: martian atmosphere, spallation and martian interior^1

    Science.gov (United States)

    Gilmour, J. D.; Whitby, J. A.; Turner, G.

    2001-01-01

    A powdered sample of Nakhla was separated into 3 subsamples. One was left otherwise untreated, one was washed in water and one etched with HNO 3 removing 6% of the original mass. We report results of isotopic analysis of xenon released by laser step heating on aliquots of each of these subsamples; some aliquots were neutron irradiated before isotopic analysis (to allow determination of I, Ba and U as daughter xenon isotopes) and some were not. There is evidence that water soluble phases contain both martian atmospheric xenon and a component with low 129Xe/ 132Xe, either martian interior xenon or terrestrial atmosphere. Higher temperature data from unirradiated aliquots of the water and acid treated samples reveal two-component mixing. One is a trapped xenon component with 129Xe/ 132Xe = 2.350 ± 0.026, isotopically identical to the martian atmosphere as measured in shock glass from shergottites. It is associated with leachable iodine, suggesting it is trapped close to grain boundaries. It may be a result of shock incorporation of adsorbed atmospheric gas. The second component is best explained as an intimate mixture of martian interior xenon and spallation xenon. The martian interior component is present at a concentration of ˜10 -12 cm 3 STP g -1 132Xe, around 40 times lower than that observed in Chassigny. Its association with spallation xenon (produced from Ba and light rare earth elements) suggests it is in the feldspathic mesostasis. We propose that it was trapped during crystallisation and reflects the mantle source of the parental magma.

  12. Coupled fluid/structure analyses of the MEGAPIE spallation source target during transients

    Energy Technology Data Exchange (ETDEWEB)

    Smith, B.L. [Thermal-Hydraulics Laboratory, Nuclear Energy and Safety Department, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland)]. E-mail: brian.smith@psi.ch; Leung, W. [Spallation Neutron Source Division, Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Zucchini, A. [UTS Tecnologie Fisiche Avanzate, Sezione Metodologie e Diagnostiche, ENEA, Bologna (Italy)

    2007-09-15

    The paper describes some R and D activities undertaken in support of the design and safe operation of MEGAPIE (MEGAwatt PIlot Experiment) spallation source target, which is scheduled to be irradiated by a proton beam in the SINQ facility at the Paul Scherrer Institute in 2006. The target material is lead bismuth eutectic (LBE), which also acts as the primary coolant. As a consequence of the spallation reactions, about 600 kW of heat would be deposited in the target during operation, and considerable R and D effort is being expended to demonstrate continuing coolability and structural integrity under a variety of operational and abnormal conditions. The paper gives three examples of transient analyses carried out as part of the safety assessment of the target: (1) a beamline trip and recovery; (2) failure of the primary electro-magnetic pump (EMP); (3) failure of the secondary EMP (used to cool the base of the target). The study involves the simultaneous application of a system-analysis code, in our case a version of RELAP5, a computational fluid dynamics (CFD) tool (CFX-4), and a structural analysis code (ABAQUS). The RELAP5 code is used to provide transient boundary conditions for a localized conjugate heat transfer analysis of the lower target region, undertaken using CFD, and includes the feed-back effects arising from the secondary cooling and control systems. A conjugate heat transfer problem is then solved using CFD, which provides time-dependent thermal and flow data within the LBE, together with the thermal and mechanical loads to the target structures. Finally, an in-house interface program is employed to transfer mesh geometry, model topology and (time-dependent) thermal/mechanical data to enable stress analysis of the principal lower-target structural components to be performed. It is demonstrated that none of the transients considered result in critical stress conditions occurring in the target components, but that further operation is not recommended

  13. ALARA Review of the Spallation Neutron Source Accumulator Ring and Transfer Lines

    Energy Technology Data Exchange (ETDEWEB)

    Haire, M.J.

    2003-06-30

    The Spallation Neutron Source (SNS) is designed to meet the growing need for new tools that will deepen our understanding in materials science, life science, chemistry, fundamental and nuclear physics, earth and environmental sciences, and engineering sciences. The SNS is an accelerator-based neutron-scattering facility that when operational will produce an average beam power of 2 MW at a repetition rate of 60 Hz. The accelerator complex consists of the front-end systems, which will include an ion source; a 1-GeV full-energy linear accelerator; a single accumulator ring and its transfer lines; and a liquid mercury target. This report documents an as-low-as-reasonably-achievable (ALARA) review of the accumulator ring and transfer lines at their early design stage. An ALARA working group was formed and conducted a review of the SNS ring and transfer lines at the {approx}25% complete design stage to help ensure that ALARA principles are being incorporated into the design. The radiological aspects of the SNS design criteria were reviewed against regulatory requirements and ALARA principles. Proposed features and measures were then reviewed against the SNS design criteria. As part of the overall review, the working group reviewed the design manual; design drawings and process and instrumentation diagrams; the environment, safety, and health manual; and other related reports and literature. The group also talked with SNS design engineers to obtain explanations of pertinent subject matter. The ALARA group found that ALARA principles are indeed being incorporated into the early design stage. Radiation fields have been characterized, and shielding calculations have been performed. Radiological issues are being adequately addressed with regard to equipment selection, access control, confinement structure and ventilation, and contamination control. Radiation monitoring instrumentation for worker and environment protection are also being considered--a good practice at this

  14. Spallation reaction study for fission products in nuclear waste: Cross section measurements for 137Cs and 90Sr on proton and deuteron

    Directory of Open Access Journals (Sweden)

    H. Wang

    2016-03-01

    Full Text Available We have studied spallation reactions for the fission products 137Cs and 90Sr for the purpose of nuclear waste transmutation. The spallation cross sections on the proton and deuteron were obtained in inverse kinematics for the first time using secondary beams of 137Cs and 90Sr at 185 MeV/nucleon at the RIKEN Radioactive Isotope Beam Factory. The target dependence has been investigated systematically, and the cross-section differences between the proton and deuteron are found to be larger for lighter spallation products. The experimental data are compared with the PHITS calculation, which includes cascade and evaporation processes. Our results suggest that both proton- and deuteron-induced spallation reactions are promising mechanisms for the transmutation of radioactive fission products.

  15. Spallation reaction study for fission products in nuclear waste: Cross section measurements for {sup 137}Cs and {sup 90}Sr on proton and deuteron

    Energy Technology Data Exchange (ETDEWEB)

    Wang, H., E-mail: wanghe@ribf.riken.jp [RIKEN Nishina Center, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Otsu, H.; Sakurai, H.; Ahn, D.S. [RIKEN Nishina Center, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Aikawa, M. [Faculty of Science, Hokkaido University, Sapporo 060-0810 (Japan); Doornenbal, P.; Fukuda, N.; Isobe, T. [RIKEN Nishina Center, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Kawakami, S. [Department of Applied Physics, University of Miyazaki, Miyazaki 889-2192 (Japan); Koyama, S. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-0033 (Japan); Kubo, T.; Kubono, S.; Lorusso, G. [RIKEN Nishina Center, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Maeda, Y. [Department of Applied Physics, University of Miyazaki, Miyazaki 889-2192 (Japan); Makinaga, A. [Graduate School of Medicine, Hokkaido University, North-14, West-5, Kita-ku, Sapporo 060-8648 (Japan); Momiyama, S. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-0033 (Japan); Nakano, K. [Department of Advanced Energy Engineering Science, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan); Niikura, M. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-0033 (Japan); Shiga, Y. [Department of Physics, Rikkyo University, 3-34-1 Nishi-Ikebukuro, Toshima, Tokyo 171-8501 (Japan); RIKEN Nishina Center, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Söderström, P.-A. [RIKEN Nishina Center, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); and others

    2016-03-10

    We have studied spallation reactions for the fission products {sup 137}Cs and {sup 90}Sr for the purpose of nuclear waste transmutation. The spallation cross sections on the proton and deuteron were obtained in inverse kinematics for the first time using secondary beams of {sup 137}Cs and {sup 90}Sr at 185 MeV/nucleon at the RIKEN Radioactive Isotope Beam Factory. The target dependence has been investigated systematically, and the cross-section differences between the proton and deuteron are found to be larger for lighter spallation products. The experimental data are compared with the PHITS calculation, which includes cascade and evaporation processes. Our results suggest that both proton- and deuteron-induced spallation reactions are promising mechanisms for the transmutation of radioactive fission products.

  16. Spallation reaction study for fission products in nuclear waste: Cross section measurements for 137Cs and 90Sr on proton and deuteron

    Science.gov (United States)

    Wang, H.; Otsu, H.; Sakurai, H.; Ahn, D. S.; Aikawa, M.; Doornenbal, P.; Fukuda, N.; Isobe, T.; Kawakami, S.; Koyama, S.; Kubo, T.; Kubono, S.; Lorusso, G.; Maeda, Y.; Makinaga, A.; Momiyama, S.; Nakano, K.; Niikura, M.; Shiga, Y.; Söderström, P.-A.; Suzuki, H.; Takeda, H.; Takeuchi, S.; Taniuchi, R.; Watanabe, Ya.; Watanabe, Yu.; Yamasaki, H.; Yoshida, K.

    2016-03-01

    We have studied spallation reactions for the fission products 137Cs and 90Sr for the purpose of nuclear waste transmutation. The spallation cross sections on the proton and deuteron were obtained in inverse kinematics for the first time using secondary beams of 137Cs and 90Sr at 185 MeV/nucleon at the RIKEN Radioactive Isotope Beam Factory. The target dependence has been investigated systematically, and the cross-section differences between the proton and deuteron are found to be larger for lighter spallation products. The experimental data are compared with the PHITS calculation, which includes cascade and evaporation processes. Our results suggest that both proton- and deuteron-induced spallation reactions are promising mechanisms for the transmutation of radioactive fission products.

  17. A 4p BaF2 detector for (n,g) cross section measurements at a spallation neutron source

    CERN Document Server

    Heil, M; Fowler, M M; Haight, R C; Käppeler, F; Rundberg, R S; Seabury, E H; Ullmann, J L; Wilhelmy, J B; Wisshak, K

    2013-01-01

    The quest for improved neutron capture cross sections for advanced reactor concepts, transmutation of radioactive wastes as well as for astrophysical scenarios of neutron capture nucleosynthesis has motivated new experimental efforts based on modern techniques. Recent measurements in the keV region have shown that a 4p BaF2 detector represents an accurate and versatile instrument for such studies. The present work deals with the potential of such a 4p BaF2 detector in combination with spallation neutron sources, which offer large neutron fluxes over a wide energy range. Detailed Monte Carlo simulations with the GEANT package have been performed to investigate the critical backgrounds at a spallation facility, to optimize the detector design, and to discuss alternative solutions.

  18. "Innovation and Intellectual Property Policies in European Research Infrastructure Consortia - PART I: The Case of the European Spallation Source ERIC"

    DEFF Research Database (Denmark)

    Yu, Helen; Wested, Jakob; Minssen, Timo

    2017-01-01

    of the problems society is facing today. To facilitate the creation and operation of such RIs, the EU adopted legal frameworks for European Research Infrastructure Consortia (ERIC). On August 31, 2015, the European Spallation Source (ESS) was established as an ERIC. Under the ERIC Regulations and ESS Statutes......Research and innovation are key pillars of the EU’s strategy to create sustainable growth and prosperity in Europe. Research infrastructures (RIs) are central instruments to implement this strategy. They bring together a wide diversity of expertise and interests to look for solutions to many......, the European Spallation Source ERIC is required to adopt various policy documents relating to the operation and management of the facility. These cover a wide variety of issues such as user access, public procurement, intellectual property rights (IPR), data management, and dissemination. One of the main goals...

  19. Physical Design of Critical Experiment Facility for Verifying Characteristics and Effects of Coupling Between Reactor and Spallation Target of ADS

    Institute of Scientific and Technical Information of China (English)

    YIN; Sheng-gui; ZHOU; Qi; LI; Yan

    2013-01-01

    For the purpose of studying and verifying characteristics and effects of coupling between reactor and spallation target of ADS,based on the critical experimental facility design criteria and the availableexperiment condition,physical design of a critical experiment facility with lead coolant is completed,using critical calculation code MONK-9A.The contents of physical designs mainly include nuclear fuel,array of fuel rods,neutron source

  20. Spallation and fission products in the (p+{sup 179}Hf) and (p+{sup nat}Hf) reactions

    Energy Technology Data Exchange (ETDEWEB)

    Karamian, S.A. [Joint Institute for Nuclear Research, Moscow Region, Dubna 141980 (Russian Federation); Ur, C.A. [Horia Hulubei National Institute of Physics and Nuclear Engineering, P.O. Box MG-6, Bucharest 077125 (Romania); Induced Gamma Emission Foundation, P.O. Box 34-81, Bucharest 010044 (Romania)], E-mail: ur@pd.infn.it; Adam, J. [Joint Institute for Nuclear Research, Moscow Region, Dubna 141980 (Russian Federation); Institute of Nuclear Physics, Rez, Prague CZ-25068 (Czech Republic); Kalinnikov, V.G.; Lebedev, N.A.; Vostokin, G.K. [Joint Institute for Nuclear Research, Moscow Region, Dubna 141980 (Russian Federation); Collins, C.B. [Center for Quantum Electronics, University of Texas at Dallas, Richardson, TX 75083 (United States); Popescu, I.I. [Induced Gamma Emission Foundation, P.O. Box 34-81, Bucharest 010044 (Romania)

    2009-03-01

    Production of Hf and Lu high-spin isomers has been experimentally studied in spallation reactions induced by intermediate energy protons. Targets of enriched {sup 179}Hf (91%) and {sup nat}Hf were bombarded with protons of energy in the range from 90 to 650 MeV provided by the internal beam of the Dubna Phasotron synchrocyclotron. The activation yields of the reaction products were measured by using the {gamma}-ray spectroscopy and radiochemistry methods. The production cross-sections obtained for the {sup 179m2}Hf, {sup 178m2}Hf and {sup 177m}Lu isomers are similar to the previously measured values from the spallation of Ta, Re and W targets. Therefore, the reactions involving emission of only a few nucleons, like (p,p'), (p,p'n) and (p,2pn), can transfer high enough angular momentum to the final residual nuclei with reasonable large cross-sections. A significant gain in the isomeric yields was obtained when enriched {sup 179}Hf targets were used. The mass distribution of the residual nuclei was measured over a wide range of masses and the fission-to-spallation ratio could be deduced as a function of the projectile energy. Features of the reaction mechanism are briefly discussed.

  1. Measurement of isotopic cross sections of spallation residues in 800 A MeV {sup 197}Au + p collisions

    Energy Technology Data Exchange (ETDEWEB)

    Rejmund, F.; Mustapha, B.; Bernas, M.; Stephan, C.; Taieb, J.; Tassan-Got, L. [Institut de Physique Nucleaire, (IN2P3/CNRS) 91 - Orsay (France); Armbruster, P.; Benlliure, J.; Enqvist, T.; Schmidt, K.H.; Taieb, J. [GSI, Planckstrasse, Darmstadt (Germany); Benlliure, J. [Universidad de Santiago de Compostela (Spain); Boudard, A.; Legrain, R.; Leray, S.; Volant, C. [CEA/Saclay, Dept. d' Astrophysique, de la Physique des Particules, de la Physique Nucleaire et de l' Instrumentation Associee (DAPNIA), 91 - Gif-sur-Yvette (France); Dufour, J.P. [CENBG, IN2P3, 33 - Gradignan (France)

    2000-07-01

    The spallation of {sup 197}Au by 800 MeV protons was investigated in inverse kinematics at GSI, Darmstadt, by use of a {sup 197}Au beam bombarding a liquid-hydrogen target. The fragment separator (FRS) was used to select and identify the reaction products prior to {beta} decay. The individual production cross sections and the kinematical properties of 396 isotopes for all elements between mercury (Z=80) and neodymium (Z=60) have been measured. A comparison with Monte Carlo calculations based on different two-step models of the spallation reaction is given. The shape of the isotopic distributions close to the projectile is found to differ strongly from that resulting from aluminium-induced fragmentation of {sup 197}Au. The mean kinetic energies of the fragments are deduced from the experimental data. The importance of the new data to improve our understanding of the spallation mechanism and the relevance for the design of accelerator-driven sub-critical reactors is discussed. (authors)

  2. Time-Reversal Invariance Violation in Neutron Scattering at Spallation Neutron Sources

    Science.gov (United States)

    Gudkov, Vladimir

    2014-09-01

    The Time Reversal Invariant Violating (TRIV) effects in neutron transmission through a nuclei target are discussed. We explore the possibility to search TRIV at new high flux Spallation Neutron Sources using two important advantages of neutron nuclei interactions: the possibility of an enhancement of T-violating observables by many orders of magnitude, and the relatively large number of the nuclear targets, which provides the assurance of avoiding possible ``accidental'' cancelations of TRI-violating effects due to unknown structural factors related to the strong interactions. This include the absence of final state interactions for a set of specific observables, the possibility to avoid of false asymmetries arising from combinations of time-reversal-invariant interactions and asymmetries in real experiment, and the comparison of expected results with existing limits on neutron, nuclear and atomic electric dipole moments (EDMs). It is shown that TRIV observables are complementary to the EDM experiments and have potential for essential improving of the current limits on the TRIV interactions. The Time Reversal Invariant Violating (TRIV) effects in neutron transmission through a nuclei target are discussed. We explore the possibility to search TRIV at new high flux Spallation Neutron Sources using two important advantages of neutron nuclei interactions: the possibility of an enhancement of T-violating observables by many orders of magnitude, and the relatively large number of the nuclear targets, which provides the assurance of avoiding possible ``accidental'' cancelations of TRI-violating effects due to unknown structural factors related to the strong interactions. This include the absence of final state interactions for a set of specific observables, the possibility to avoid of false asymmetries arising from combinations of time-reversal-invariant interactions and asymmetries in real experiment, and the comparison of expected results with existing limits on neutron

  3. Finite element analysis and frequency shift studies for the bridge coupler of the coupled cavity linear accelerator of the spallation neutron source.

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Z. (Zukun)

    2001-01-01

    The Spallation Neutron Source (SNS) is an accelerator-based neutron scattering research facility. The linear accelerator (linac) is the principal accelerating structure and divided into a room-temperature linac and a superconducting linac. The normal conducting linac system that consists of a Drift Tube Linac (DTL) and a Coupled Cavity Linac (CCL) is to be built by Los Alamos National Laboratory. The CCL structure is 55.36-meters long. It accelerates H- beam from 86.8 Mev to 185.6 Mev at operating frequency of 805 MHz. This side coupled cavity structure has 8 cells per segment, 12 segments and 11 bridge couplers per module, and 4 modules total. A 5-MW klystron powers each module. The number 3 and number 9 bridge coupler of each module are connected to the 5-MW RF power supply. The bridge coupler with length of 2.5 {beta}{gamma} is a three-cell structure and located between the segments and allows power flow through the module. The center cell of each bridge coupler is excited during normal operation. To obtain a uniform electromagnetic filed and meet the resonant frequency shift, the RF induced heat must be removed. Thus, the thermal deformation and frequency shift studies are performed via numerical simulations in order to have an appropriate cooling design and predict the frequency shift under operation. The center cell of the bridge coupler also contains a large 4-inch slug tuner and a tuning post that used to provide bulk frequency adjustment and field intensity adjustment, so that produce the proper total field distribution in the module assembly.

  4. A Large Neutrino Detector Facility at the Spallation Neutron Source at Oak Ridge National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Efremenko, Y.V.

    1999-02-14

    The ORLaND (Oak Ridge Large Neutrino Detector) collaboration proposes to construct a large neutrino detector in an underground experimental hall adjacent to the first target station of the Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory. The main mission of a large (2000 ton) Scintillation-Cherenkov detector is to measure {bar {nu}}{sub {mu}} {r_arrow} {bar {nu}}{sub e} neutrino oscillation parameters more accurately than they can be determined in other experiments, or significantly extending the covered parameter space below (sin'20 {le} 10{sup {minus}4}). In addition to the neutrino oscillation measurements, ORLaND would be capable of making precise measurements of sin{sup 2} {theta}{sub W}, search for the magnetic moment of the muon neutrino, and investigate the anomaly in the KARMEN time spectrum, which has been attributed to a new neutral particle. With the same facility an extensive program of measurements of neutrino nucleus cross sections is also planned to support nuclear astrophysics.

  5. Overview of the conceptual design of the future VENUS beamline at the Spallation Neutron Source

    Energy Technology Data Exchange (ETDEWEB)

    Bilheux, Hassina Z [ORNL; Herwig, Kenneth W [ORNL; Keener, Wylie S [ORNL; Davis, Larry E [ORNL

    2015-01-01

    VENUS will be a world-class neutron-imaging instrument that will uniquely utilize the Spallation Neutron Source (SNS) time-of-flight (TOF) capabilities to measure and characterize objects across several length scales (mm to m). When completed, VENUS will provide academia, industry and government laboratories with the opportunity to advance scientific research in areas such as energy, materials, additive manufacturing, geosciences, transportation, engineering, plant physiology, biology, etc. It is anticipated that a good portion of the VENUS user community will have a strong engineering/industrial research focus. Installed at Beamline 10 (BL10), VENUS will be a 25-m neutron imaging facility with the capability to fully illuminate (i.e., umbra illumination) a 20 cm x 20 cm detector area. The design allows for a 28 cm x 28 cm field of view when using the penumbra to 80% of the full illumination flux. A sample position at 20 m will be implemented for magnification measurements. The optical components are comprised of a series of selected apertures, T0 and bandwidth choppers, beam scrapers, a fast shutter to limit sample activation, and flight tubes filled with Helium. Techniques such as energy selective, Bragg edge and epithermal imaging will be available at VENUS

  6. Fermilab Project X nuclear energy application: Accelerator, spallation target and transmutation technology demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Gohar, Yousry; /Argonne; Johnson, David; Johnson, Todd; Mishra, Shekhar; /Fermilab

    2011-04-01

    The recent paper 'Accelerator and Target Technology for Accelerator Driven Transmutation and Energy Production' and report 'Accelerators for America's Future' have endorsed the idea that the next generation particle accelerators would enable technological breakthrough needed for nuclear energy applications, including transmutation of waste. In the Fall of 2009 Fermilab sponsored a workshop on Application of High Intensity Proton Accelerators to explore in detail the use of the Superconducting Radio Frequency (SRF) accelerator technology for Nuclear Energy Applications. High intensity Continuous Wave (CW) beam from the Superconducting Radio Frequency (SRF) Linac (Project-X) at beam energy between 1-2 GeV will provide an unprecedented experimental and demonstration facility in the United States for much needed nuclear energy Research and Development. We propose to carry out an experimental program to demonstrate the reliability of the accelerator technology, Lead-Bismuth spallation target technology and a transmutation experiment of spent nuclear fuel. We also suggest that this facility could be used for other Nuclear Energy applications.

  7. Thermohydraulic behavior of the liquid metal target of a spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Y.

    1996-06-01

    The author presents work done on three main problems. (1) Natural circulation in double coaxial cylindircal container: The thermohydraulic behaviour of the liquid metal target of the spallation neutron source at PSI has been investigated. The configuration is a natural-circulation loop in a concentric double-tube-type container. The results show that the natural-circulation loop concept is valid for the design phase of the target construction, and the current specified design criteria will be fulfilled with the proposed parameter values. (2) Flow around the window: Water experiments were performed for geometry optimisation of the window shape of the SINQ container for avoiding generating recirculation zones at peripheral area and the optimal cooling of the central part of the beam entrance window. Flow visualisation technique was mainly used for various window shapes, gap distance between the window and the guide tube edge. (3) Flow in window cooling channels: Flows in narrow gaps of cooling channels of two different types of windows were studied by flow visualisation techniques. One type is a slightly curved round cooling channel and the other is hemispherical shape, both of which have only 2 mm gap distance and the water inlet is located on one side and flows out from the opposite side. In both cases, the central part of the flow area has lower velocity than peripheral area.

  8. Improved design of proton source and low energy beam transport line for European Spallation Source

    Energy Technology Data Exchange (ETDEWEB)

    Neri, L., E-mail: neri@lns.infn.it; Celona, L.; Gammino, S.; Mascali, D.; Castro, G.; Ciavola, G. [Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare, Via S. Sofia 62, 95123 Catania (Italy); Torrisi, G. [Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare, Via S. Sofia 62, 95123 Catania (Italy); Dipartimento di Ingegneria dell’Informazione, delle Infrastrutture e dell’Energia Sostenibile, Università Mediterranea di Reggio Calabria, Via Graziella, 89122 Reggio Calabria (Italy); Cheymol, B.; Ponton, A. [European Spallation Source ESS AB, Lund (Sweden); Galatà, A. [Laboratori Nazionali di Legnaro, Istituto Nazionale di Fisica Nucleare, Viale dell' università 2, 35020 Legnaro (Italy); Patti, G. [Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare, Via S. Sofia 62, 95123 Catania (Italy); Laboratori Nazionali di Legnaro, Istituto Nazionale di Fisica Nucleare, Viale dell' università 2, 35020 Legnaro (Italy); Gozzo, A.; Lega, L. [Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare, Via S. Sofia 62, 95123 Catania (Italy); Dipartimento di Ingegneria Informatica e delle Telecomunicazioni, Università degli Studi di Catania, Viale Andrea Doria 6, 95123 Catania (Italy)

    2014-02-15

    The design update of the European Spallation Source (ESS) accelerator is almost complete and the construction of the prototype of the microwave discharge ion source able to provide a proton beam current larger than 70 mA to the 3.6 MeV Radio Frequency Quadrupole (RFQ) started. The source named PS-ESS (Proton Source for ESS) was designed with a flexible magnetic system and an extraction system able to merge conservative solutions with significant advances. The ESS injector has taken advantage of recent theoretical updates and new plasma diagnostics tools developed at INFN-LNS (Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare). The design strategy considers the PS-ESS and the low energy beam transport line as a whole, where the proton beam behaves like an almost neutralized non-thermalized plasma. Innovative solutions have been used as hereinafter described. Thermo-mechanical optimization has been performed to withstand the chopped beam and the misaligned focused beam over the RFQ input collimator; the results are reported here.

  9. Design of a horizontal neutron reflectometer for the European Spallation Source

    CERN Document Server

    Nekrassov, D; Lieutenant, K; Moulin, J -F; Strobl, M; Steitz, R

    2013-01-01

    A design study of a horizontal neutron reflectometer adapted to the general baseline of the long pulse European Spallation Source (ESS) is presented. The instrument layout comprises solutions for the neutron guide, high-resolution pulse shaping and beam bending onto a sample surface being so far unique in the field of reflectometry. The length of this instrument is roughly 55 m, enabling $\\delta \\lambda / \\lambda$ resolutions from 0.5% to 10%. The incident beam is focussed in horizontal plane to boost measurements of sample sizes of 1*1 cm{^2} and smaller with potential beam deflection in both downward and upward direction. The range of neutron wavelengths untilized by the instrument is 2 to 7.1 (12.2, ...) {\\AA}, if every (second, ...) neutron source ulse is used. Angles of incidence can be set between 0{\\deg} and 9{\\deg} with a total accessible q-range from 4*10^{-3} {\\AA}^{-1} up to 1 {\\AA}^{-1}. The instrument operates both in {\\theta}/{\\theta} (free liquid surfaces) and {\\theta}/2{\\theta} (solid/liquid, ...

  10. On the nucleon effective mass role to the high energy proton spallation reactions

    Energy Technology Data Exchange (ETDEWEB)

    Santos, B.M., E-mail: biank_ce@if.uff.br [Instituto de Física, Universidade Federal Fluminense, Av. Gal. Milton Tavares de Souza, 24210-346 Niterói, RJ (Brazil); Instituto Militar de Engenharia, Praça General Tibúrcio 80, 22290-270 Rio de Janeiro, RJ (Brazil); Pinheiro, A.R.C. [Centro Brasileiro de Pesquisas Físicas, Rua Dr. Xavier Sigaud 150, 22290-180 Rio de Janeiro, RJ (Brazil); Universidade Federal do Acre, BR 364 km 04, 69920-900 Rio Branco, AC (Brazil); Gonçalves, M. [Comissão Nacional de Energia Nuclear, Rua General Severiano 90, 22290-901 Rio de Janeiro, RJ (Brazil); Duarte, S.B. [Centro Brasileiro de Pesquisas Físicas, Rua Dr. Xavier Sigaud 150, 22290-180 Rio de Janeiro, RJ (Brazil); Cabral, R.G. [Instituto Militar de Engenharia, Praça General Tibúrcio 80, 22290-270 Rio de Janeiro, RJ (Brazil)

    2016-04-15

    We explore the effect of the nucleon effective mass to the dynamic evolution of the rapid phase of proton–nucleus spallation reactions. The analysis of the relaxation time for the non-equilibrium phase is studied by variations in the effective mass parameter. We determine the final excitation energy of the hot residual nucleus at the end of cascade phase and the de-excitation of the nuclear system is carried out considering the competition of particle evaporation and fission processes. It was shown that the excitation energy depends of the hot compound residual nucleus at the end of the rapid phase on the changing effective mass. The multiplicity of particles was also analyzed in cascade and evaporation phase of the reaction. The use of nucleon effective mass during cascade phase can be considered as an effect of the many-body nuclear interactions not included explicitly in a treatment to the nucleon–nucleon interaction inside the nucleus. This procedure represents a more realistic scenario to obtain the neutron multiplicity generated in this reaction, which is a benchmark for the calculation of the neutronic in the ADS reactors.

  11. Investigations with Gaseous Electron Multipliers for use on the ISIS spallation neutron source

    Science.gov (United States)

    Duxbury, D.; Rhodes, N.; Schooneveld, E.; Spill, E.

    2012-01-01

    Several investigations have been undertaken to ascertain the suitability of gaseous electron multipliers (GEMs) for use as a neutron detector on the ISIS spallation neutron source. Our initial investigations focused purely on whether these devices could be operated at the elevated pressure of 3He and CF4 necessary for 1mm position resolution (2.6 bars of CF4). In fact we were able to operate the GEMs at suitable gains with 3.5 bars of CF4. However encouraging these results were, we found that the GEMs charged up over time, which we postulated was due to the kapton substrate. A similar problem was seen at the early stages of the development of the microstrip gas chamber (MSGC), a solution of which was to use the semiconducting glass Schott S8900 as the substrate. Therefore we focused our attention to the manufacture of a GEM structure on an S8900 substrate. Our first devices were manufactured from 1mm thick glass and exhibit gains in excess of 1 × 104 for a single GEM stage in an argon isobutane gas mixture, when illuminated with 55Fe x-rays. A small amount of charging under irradiation has been observed in a flowing gas mixture, but the GEMs quickly stabilise and track atmospheric conditions. Further measurements in a 3He:CF4 atmosphere will show how suited these devices are to the needs of ISIS.

  12. Gadolinium-148 And Other Spallation Production Cross Section Measurements For Accelerator Target Facilities

    CERN Document Server

    Kelley, K C

    2004-01-01

    At the Los Alamos Neutron Science Center accelerator complex, protons are accelerated to 800 MeV and directed to two tungsten targets, Target 4 at the Weapons Neutron Research facility and the 1L target at the Lujan Center. The Department of Energy requires hazard classification analyses to be performed on these targets and places limits on certain radionuclide inventories in the targets to avoid characterizing the facilities as “nuclear facilities.” Gadolinium-148 is a radionuclide created from the spallation of tungsten. Allowed isotopic inventories are particularly low for this isotope because it is an alpha-particle emitter with a 75-year half-life. The activity level of Gadolinium-148 is low, but it encompasses almost two-thirds of the total dose burden for the two tungsten targets based on present yield estimates. From a hazard classification standpoint, this severely limits the lifetime of these tungsten targets. The cross section is not well-established experimentally and this is t...

  13. Improvements to the internal and external antenna H(-) ion sources at the Spallation Neutron Source.

    Science.gov (United States)

    Welton, R F; Dudnikov, V G; Han, B X; Murray, S N; Pennisi, T R; Pillar, C; Santana, M; Stockli, M P; Turvey, M W

    2014-02-01

    The Spallation Neutron Source (SNS), a large scale neutron production facility, routinely operates with 30-40 mA peak current in the linac. Recent measurements have shown that our RF-driven internal antenna, Cs-enhanced, multi-cusp ion sources injects ∼55 mA of H(-) beam current (∼1 ms, 60 Hz) at 65-kV into a Radio Frequency Quadrupole (RFQ) accelerator through a closely coupled electrostatic Low-Energy Beam Transport system. Over the last several years a decrease in RFQ transmission and issues with internal antennas has stimulated source development at the SNS both for the internal and external antenna ion sources. This report discusses progress in improving internal antenna reliability, H(-) yield improvements which resulted from modifications to the outlet aperture assembly (applicable to both internal and external antenna sources) and studies made of the long standing problem of beam persistence with the external antenna source. The current status of the external antenna ion source will also be presented.

  14. High Field Pulsed Magnets for Neutron Scattering at the Spallation Neutron Source

    Science.gov (United States)

    Granroth, G. E.; Lee, J.; Fogh, E.; Christensen, N. B.; Toft-Petersen, R.; Nojiri, H.

    2015-03-01

    A High Field Pulsed Magnet (HFPM) setup, is in use at the Spallation Nuetron Source(SNS), Oak Ridge National Laboratory. With this device, we recently measured the high field magnetic spin structure of LiNiPO4. The results of this study will be highlighted as an example of possible measurements that can be performed with this device. To further extend the HFPM capabilities at SNS, we have learned to design and wind these coils in house. This contribution will summarize the magnet coil design optimization procedure. Specifically by varying the geometry of the multi-layer coil, we arrive at a design that balances the maximum field strength, neutron scattering angle, and the field homogeneity for a specific set of parameters. We will show that a 6.3kJ capacitor bank, can provide a magnetic field as high as 30T for a maximum scattering angle around 40° with homogeneity of +/- 4 % in a 2mm diameter spherical volume. We will also compare the calculations to measurements from a recently wound test coil. This work was supported in part by the Lab Directors' Research and Development Fund of ORNL.

  15. Improved design of proton source and low energy beam transport line for European Spallation Source

    Science.gov (United States)

    Neri, L.; Celona, L.; Gammino, S.; Mascali, D.; Castro, G.; Torrisi, G.; Cheymol, B.; Ponton, A.; Galatà, A.; Patti, G.; Gozzo, A.; Lega, L.; Ciavola, G.

    2014-02-01

    The design update of the European Spallation Source (ESS) accelerator is almost complete and the construction of the prototype of the microwave discharge ion source able to provide a proton beam current larger than 70 mA to the 3.6 MeV Radio Frequency Quadrupole (RFQ) started. The source named PS-ESS (Proton Source for ESS) was designed with a flexible magnetic system and an extraction system able to merge conservative solutions with significant advances. The ESS injector has taken advantage of recent theoretical updates and new plasma diagnostics tools developed at INFN-LNS (Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare). The design strategy considers the PS-ESS and the low energy beam transport line as a whole, where the proton beam behaves like an almost neutralized non-thermalized plasma. Innovative solutions have been used as hereinafter described. Thermo-mechanical optimization has been performed to withstand the chopped beam and the misaligned focused beam over the RFQ input collimator; the results are reported here.

  16. Optimizing moderator dimensions for neutron scattering at the spallation neutron source.

    Science.gov (United States)

    Zhao, J K; Robertson, J L; Herwig, Kenneth W; Gallmeier, Franz X; Riemer, Bernard W

    2013-12-01

    In this work, we investigate the effect of neutron moderator dimensions on the performance of neutron scattering instruments at the Spallation Neutron Source (SNS). In a recent study of the planned second target station at the SNS facility, we have found that the dimensions of a moderator play a significant role in determining its surface brightness. A smaller moderator may be significantly brighter over a smaller viewing area. One of the immediate implications of this finding is that for modern neutron scattering instrument designs, moderator dimensions and brightness have to be incorporated as an integrated optimization parameter. Here, we establish a strategy of matching neutron scattering instruments with moderators using analytical and Monte Carlo techniques. In order to simplify our treatment, we group the instruments into two broad categories: those with natural collimation and those that use neutron guide systems. For instruments using natural collimation, the optimal moderator selection depends on the size of the moderator, the sample, and the moderator brightness. The desired beam divergence only plays a role in determining the distance between sample and moderator. For instruments using neutron optical systems, the smallest moderator available that is larger than the entrance dimension of the closest optical element will perform the best (assuming, as is the case here that smaller moderators are brighter).

  17. Cumulative beam break-up study of the spallation neutron source superconducting linac

    CERN Document Server

    Jeon, D; Krafft, G A; Yunn, B; Sundelin, R; Delayen, J; Kim, S; Doleans, M

    2002-01-01

    Beam instabilities due to High Order Modes (HOMs) are a concern to superconducting (SC) linacs such as the Spallation Neutron Source (SNS) linac. The effects of pulsed mode operation on transverse and longitudinal beam breakup instability are studied for H sup - beam in a consistent manner for the first time. Numerical simulation indicates that cumulative transverse beam breakup instabilities are not a concern in the SNS SC linac, primarily due to the heavy mass of H sup - beam and the HOM frequency spread resulting from manufacturing tolerances. As little as +-0.1 MHz HOM frequency spread stabilizes all the instabilities from both transverse HOMs, and also acts to stabilize the longitudinal HOMs. Such an assumed frequency spread of +-0.1 MHz HOM is small, and hence conservative compared with measured values of sigma=0.00109(f sub H sub O sub M -f sub 0)/f sub 0 obtained from Cornell and the Jefferson Lab Free Electron Laser cavities. However, a few cavities may hit resonance lines and generate a high heat lo...

  18. The Nanoscale Ordered MAterials Diffractometer NOMAD at the Spallation Neutron Source SNS

    Energy Technology Data Exchange (ETDEWEB)

    Feygenson, Mikhail [ORNL; Carruth, John William [ORNL; Hoffmann, Ron [ORNL; Chipley, Kenneth King [ORNL; Neuefeind, Joerg C [ORNL

    2012-01-01

    The Nanoscale Ordered Materials Diffractometer (NOMAD) is neutron time-of-flight diffractometer designed to determine pair dist ribution functions of a wide range of materials ranging from short range ordered liquids to long range ordered crystals. Due to a large neutron flux provided by the Spallation Neutron Source SNS and a large detector coverage neutron count-rates exceed comparable instruments by one to two orders of magnitude. This is achieved while maintaining a relatively high momentum transfer resolution of a $\\delta Q/Q \\sim 0.8\\%$ FWHM (typical), and an achievable $\\delta Q/Q$ of 0.24\\% FWHM (best). The real space resolution is related to the maximum momentum transfer; A maximum momentum transfer of 50\\AA$^{-1}$ can be achieved routinely and the maximum momentum transfer given by the detector configuration and the incident neutron spectrum is 125 \\AA$^{-1}$. High stability of the source and the detector allow small contrast isotope experiments to be performed. A detailed description of the instrument is given and the results of experiments with standard samples are discussed.

  19. The Nanoscale Ordered MAterials Diffractometer NOMAD at the Spallation Neutron Source SNS

    Energy Technology Data Exchange (ETDEWEB)

    Neuefeind, Joerg, E-mail: neuefeindjc@ornl.gov [Neutron Scattering Science Directorate, Oak Ridge National Laboratory, 1 Bethel Valley Road, Oak Ridge, TN 37831-6475 (United States); Feygenson, Mikhail; Carruth, John; Hoffmann, Ron; Chipley, Kenneth K. [Neutron Scattering Science Directorate, Oak Ridge National Laboratory, 1 Bethel Valley Road, Oak Ridge, TN 37831-6475 (United States)

    2012-09-15

    The Nanoscale Ordered MAterials Diffractometer (NOMAD) is neutron time-of-flight diffractometer designed to determine pair distribution functions of a wide range of materials ranging from short range ordered liquids to long range ordered crystals. Due to a large neutron flux provided by the Spallation Neutron Source SNS and a large detector coverage neutron count-rates exceed comparable instruments by one to two orders of magnitude. This is achieved while maintaining a relatively high momentum transfer resolution of a {delta}Q/Q{approx}0.8% FWHM (typical), and a possible {delta}Q/Qof0.24% FWHM (best). The real space resolution is related to the maximum momentum transfer; a maximum momentum transfer of 50 Angstrom-Sign {sup -1} can be obtained routinely and the maximum momentum transfer given by the detector configuration and the incident neutron spectrum is 125 Angstrom-Sign {sup -1}. High stability of the source and the detector allow small contrast isotope experiments to be performed. A detailed description of the instrument is given and the results of experiments with standard samples are discussed.

  20. The Nanoscale Ordered MAterials Diffractometer NOMAD at the Spallation Neutron Source SNS

    Science.gov (United States)

    Neuefeind, Jörg; Feygenson, Mikhail; Carruth, John; Hoffmann, Ron; Chipley, Kenneth K.

    2012-09-01

    The Nanoscale Ordered MAterials Diffractometer (NOMAD) is neutron time-of-flight diffractometer designed to determine pair distribution functions of a wide range of materials ranging from short range ordered liquids to long range ordered crystals. Due to a large neutron flux provided by the Spallation Neutron Source SNS and a large detector coverage neutron count-rates exceed comparable instruments by one to two orders of magnitude. This is achieved while maintaining a relatively high momentum transfer resolution of a δQ/Q ˜0.8% FWHM (typical), and a possible δQ/Q of 0.24% FWHM (best). The real space resolution is related to the maximum momentum transfer; a maximum momentum transfer of 50 Å-1 can be obtained routinely and the maximum momentum transfer given by the detector configuration and the incident neutron spectrum is 125 Å. High stability of the source and the detector allow small contrast isotope experiments to be performed. A detailed description of the instrument is given and the results of experiments with standard samples are discussed.

  1. Thermal hydraulic design and decay heat removal of a solid target for a spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Takenaka, N. [Department of Mechanical Engineering, Kobe University, Kobe (Japan)]. E-mail: takenaka@mech.kobe-u.ac.jp; Nio, D. [Hokkaido University, Sapporo (Japan); Kiyanagi, Y. [Hokkaido University, Sapporo (Japan); Mishima, K. [Kyoto University Research Reactor Institute, Kumatori (Japan); Kawai, M. [High Energy Accelerator Research Institute, Tsukuba (Japan); Furusaka, M. [High Energy Accelerator Research Institute, Tsukuba (Japan)

    2005-08-01

    Thermal hydraulic design and thermal stress calculations were conducted for a water-cooled solid target irradiated by a MW-class proton beam for a spallation neutron source. Plate type and rod bundle type targets were examined. The thickness of the plate and the diameter of the rod were determined based on the maximum and the wall surface temperature. The thermal stress distributions were calculated by a finite element method (FEM). The neutronics performance of the target is roughly proportional to its average density. The averaged densities of the designed targets were calculated for tungsten plates, tantalum-clad tungsten plates, tungsten rods sheathed by tantalum and Zircaloy and they were compared with mercury density. It was shown that the averaged density was highest for the tungsten plates and was high for the tantalum cladding tungsten plates, the tungsten rods sheathed by tantalum and Zircaloy in order. They were higher than or equal to that of mercury for the 1-2 MW proton beams. Tungsten target without the cladding or the sheath is not practical due to corrosion by water under irradiation condition. Therefore, the tantalum cladding tungsten plate already made successfully by HIP and the sheathed tungsten rod are the candidate of high performance solid targets. The decay heat of each target was calculated. It was low enough low compared to that of ISIS for the target without tantalum but was about four times as high as that of ISIS when the thickness of the tantalum cladding was 0.5 mm. Heat removal methods of the decay heat with tantalum were examined. It was shown that a special cooling system was required for the target exchange when tantalum was used for the target. It was concluded that the tungsten rod target sheathed with stainless steel or Zircaloy was the most reliable from the safety considerations and had similar neutronics performance to that of mercury.

  2. Migration of radionuclides in a gas cooled solid state spallation target

    Energy Technology Data Exchange (ETDEWEB)

    Jørgensen, Thomas; Severin, Gregory; Jensen, Mikael, E-mail: kmje@dtu.dk

    2015-02-15

    Highlights: • We have investigated diffusion of (primarily) tritium in solid tungsten. • We have used an analytical and a numerical approach. • The temperature of tungsten changes with a short-term pulse driven proton beam. • The time structure of the temperature has a negligible impact on the diffusion. • Radioactive release at the surface can be found by solving the differential equation. - Abstract: The current design of the ESS (European Spallation Source) program proposes a rotating solid tungsten target cooled by helium gas and a pulsed beam of protons. For safety reasons any design has to address whether or not the induced radionuclidic isotopes in the target migrate. In this paper we have investigated the diffusion of (primarily) tritium in solid tungsten to see if a pulse driven short-term variation in temperature (temperature peaks separated by one turn of the wheel (2.36 s)) could possibly give rise to wave-like migration of the radionuclides, possibly accelerating the overall release. In order to calculate the diffusion in the solid tungsten target two approaches have been used. One neglecting the time structure of the beam and thermal cycling of the target, and one numerical, discrete time step simulation to capture the effects of the thermal cycling on the diffusion behavior. We found that the time structure of the of the temperature has a negligible impact on the diffusion, and that the radioactive release at the surface can be calculated safely by solving the differential equation (Fick's law) using an appropriate temperature to calculate the diffusion constant.

  3. Structural design study of a proton beam window for a 1-MW spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Teraoku, Takuji; Terada, Atsuhiko; Maekawa, Fujio; Meigo, Shin-ichiro; Kaminaga, Masanori; Ishikura, Syuichi; Hino, Ryutaro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2003-03-01

    A 1-MW spallation neutron source aiming at materials and life science researches will be constructed under the JAERI-KEK High-intensity Proton Accelerator Project (J-PARC). A proton beam passes through a proton beam window, and be injected into a target of the neutron source. The proton beam window functions as a boundary wall between a high vacuum area in the proton beam line and a helium atmosphere at about atmospheric pressure in a helium vessel which contains the target and moderators. The proton beam window is cooled by light water because high heat-density is generated in the window material by interactions with the proton beam. Then, uniformity of the water flow is requested at the window to suppress a hot-spot that causes excessive thermal stress and cooling water boiling. Also, the window has to be strong enough in its structure for inner stress due to water pressure and thermal stress due to heat generation. In this report, we propose two types of proton beam windows; one flat-type that is easy to manufacture, and the other, curved-type that has high stress resistivity. As a part of design study for the windows, evaluation of strength of structure and thermal hydraulic analysis were conducted. As a result, it was found that sufficient heat removal was assured with uniform water flow at the window, and stress caused by internal water pressure and thermal stress could be maintained below allowable stress values. Accordingly, it was confirmed that the proton beam window designs were feasible. (author)

  4. Thermal hydraulic design and decay heat removal of a solid target for a spallation neutron source

    Science.gov (United States)

    Takenaka, N.; Nio, D.; Kiyanagi, Y.; Mishima, K.; Kawai, M.; Furusaka, M.

    2005-08-01

    Thermal hydraulic design and thermal stress calculations were conducted for a water-cooled solid target irradiated by a MW-class proton beam for a spallation neutron source. Plate type and rod bundle type targets were examined. The thickness of the plate and the diameter of the rod were determined based on the maximum and the wall surface temperature. The thermal stress distributions were calculated by a finite element method (FEM). The neutronics performance of the target is roughly proportional to its average density. The averaged densities of the designed targets were calculated for tungsten plates, tantalum clad tungsten plates, tungsten rods sheathed by tantalum and Zircaloy and they were compared with mercury density. It was shown that the averaged density was highest for the tungsten plates and was high for the tantalum cladding tungsten plates, the tungsten rods sheathed by tantalum and Zircaloy in order. They were higher than or equal to that of mercury for the 1 2 MW proton beams. Tungsten target without the cladding or the sheath is not practical due to corrosion by water under irradiation condition. Therefore, the tantalum cladding tungsten plate already made successfully by HIP and the sheathed tungsten rod are the candidate of high performance solid targets. The decay heat of each target was calculated. It was low enough low compared to that of ISIS for the target without tantalum but was about four times as high as that of ISIS when the thickness of the tantalum cladding was 0.5 mm. Heat removal methods of the decay heat with tantalum were examined. It was shown that a special cooling system was required for the target exchange when tantalum was used for the target. It was concluded that the tungsten rod target sheathed with stainless steel or Zircaloy was the most reliable from the safety considerations and had similar neutronics performance to that of mercury.

  5. Low level rf system for the European Spallation Source’s Bilbao linac

    Directory of Open Access Journals (Sweden)

    Hooman Hassanzadegan

    2011-05-01

    Full Text Available Design and some performance results of the pulsed digital low level radio frequency (LLRF for the radio frequency quadrupole (RFQ systems of Rutherford Appleton Laboratory–front end test stand and the future European Spallation Source Bilbao linac are presented. For rf field regulation, the design is based on direct rf-to-baseband conversion using an analog in-phase quadrature (IQ demodulator, high-speed sampling of the I/Q components, baseband signal processing in a field-programmable gate array (FPGA, conversion to analog, and IQ modulation. This concept leads to a simple and versatile LLRF system which can be used for a large variety of rf frequencies and virtually any LLRF application including cw, ramping, and pulsed. In order to improve the accuracy of the probe voltage measurement, errors associated with the use of analog IQ demodulators have been identified and corrected by FPGA algorithms and proper setting of the feedback loop parameters. Furthermore, a baseband-equivalent model for the rf plant is developed in MATLAB-Simulink to study the RFQ transient response under beam loading in the presence of phase and delay errors. The effect of the unwanted resonant modes on the feedback loop stability and the LLRF considerations to avoid such instabilities are discussed and compared to some other machines such as the ILC and the European free electron laser . The practical results obtained from tests with a mock-up cavity and an RFQ cold model verify that amplitude and phase stabilities down to a fraction of one percent and one degree and phase margins larger than ±50° can be achieved with this method preserving the linearity and bandwidth of the feedback loops.

  6. Formation of x-ray Newton’s rings from nano-scale spallation shells of metals in laser ablation

    Directory of Open Access Journals (Sweden)

    Masaharu Nishikino

    2017-01-01

    Full Text Available The initial stages of the femtosecond (fs laser ablation process of gold, platinum, and tungsten were observed by single-shot soft x-ray imaging technique. The formation and evolution of soft x-ray Newton’s rings (NRs were found for the first time. The soft x-ray NRs are caused by the interference between the bulk ablated surface and nanometer-scale thin spallation layer; they originate from the metal surface at pump energy fluence of around 1 J/cm2 and work as a flying soft x-ray beam splitter.

  7. Formation of x-ray Newton's rings from nano-scale spallation shells of metals in laser ablation

    Science.gov (United States)

    Nishikino, Masaharu; Hasegawa, Noboru; Tomita, Takuro; Minami, Yasuo; Eyama, Takashi; Kakimoto, Naoya; Izutsu, Rui; Baba, Motoyoshi; Kawachi, Tetsuya; Suemoto, Tohru

    2017-01-01

    The initial stages of the femtosecond (fs) laser ablation process of gold, platinum, and tungsten were observed by single-shot soft x-ray imaging technique. The formation and evolution of soft x-ray Newton's rings (NRs) were found for the first time. The soft x-ray NRs are caused by the interference between the bulk ablated surface and nanometer-scale thin spallation layer; they originate from the metal surface at pump energy fluence of around 1 J/cm2 and work as a flying soft x-ray beam splitter.

  8. {sup 99}Tc transmutation by spallation neutrons produced in a large lead block; Transmutation de {sup 99}Tc par des neutrons de spallation produits dans un grand massif de plomb

    Energy Technology Data Exchange (ETDEWEB)

    Andriamonje, S.; Arnould, H.; Bompas, C.A.; Del Moral, R.; Lacoste, V. [Centre d`Etudes Nucleaires, Bordeaux-1 Univ., 33 Gradignan (France); TARC Collaboration under leadership of C. Rubbia

    1997-06-01

    In the search of hybrid system (the coupling of the particle accelerator to an under-critical reactor) for radioactive waste transmutation the TARC (Transmutation by Adiabatic Resonance Crossing) program has been developed. One of the target of the TARC program is the study of the efficiency of a `Energy Amplifier` system for nuclear waste incineration. Among the radioactive wastes the most interesting is the fission product {sup 99}Tc from nuclear plants heaving a half-live of {approx} 10{sup 5} years. Using a fast rabbit technique and gamma ray spectroscopy, the transmutation rate of {sup 99}Tc by spallation neutrons inside a large lead block was measured. The data from each 9 s rabbit cycle were stocked by means of an acquisition system based on the CERN CASCADE code especially adapted for gamma spectroscopy and able to catch large amounts of coincidence events. The measurements technique is described and the preliminary results are given. Also, in progress are simulations using new technique for production and propagation of neutrons in lead. Due to the plenty of spallation neutrons the capability of burning certain nuclear wastes is already proved

  9. A prototype RF power source for CSNS/RCS

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    A prototype RF power source has been built to supply high RF power to a ferrite-loaded cavity, which is a part of R&D of the Rapid Cycling Synchrotron of China Spallation Neutron Source (CSNS/RCS). A direct fast RF feedback amplifier, a 4:1 impedance transformer and auto tuning grid were locally located to compensate the heavy beam loading of CSNS/RCS. Design and commissioning of the RF power source is discussed here, also with some advice on system improvement.

  10. Spallation reaction study for fission products in nuclear waste: Cross section measurements for 137Cs, 90Sr and 107Pd on proton and deuteron

    Directory of Open Access Journals (Sweden)

    Wang He

    2017-01-01

    Full Text Available Spallation reactions for the long-lived fission products 137Cs, 90Sr and 107Pd have been studied for the purpose of nuclear waste transmutation. The cross sections on the proton- and deuteron-induced spallation were obtained in inverse kinematics at the RIKEN Radioactive Isotope Beam Factory. Both the target and energy dependences of cross sections have been investigated systematically. and the cross-section differences between the proton and deuteron are found to be larger for lighter fragments. The experimental data are compared with the SPACS semi-empirical parameterization and the PHITS calculations including both the intra-nuclear cascade and evaporation processes.

  11. RF power coupling for the CSNS DTL

    Science.gov (United States)

    Liu, Hua-Chang; Peng, Jun; Yin, Xue-Jun; Ouyang, Hua-Fu; Fu, Shi-Nian

    2011-01-01

    The China Spallation Neutron Source (CSNS) drift tube linac (DTL) consists of four tanks and each tank is fed by a 2.5 MW klystron. Accurate predication of RF coupling between the RF cavity and ports is very important for DTL RF coupler design. An iris-type coupler is chosen to couple the RF power to the DTL accelerating cavity. The physical design of the DTL coupler and the calculations of RF coupling between the cavity and coupler are carried out. The results from the numerical simulations are in excellent agreement with the analytical results.

  12. RF power coupling for the CSNS DTL

    Institute of Scientific and Technical Information of China (English)

    LIU Hua-Chang; PENG Jun; YIN Xue-Jun; OUYANG Hua-Fu; FU Shi-Nian

    2011-01-01

    The China Spallation Neutron Source(CSNS)drift tube linac(DTL)consists of four tanks and each tank is fed by a 2.5 MW klystron.Accurate predication of RF coupling between the RF cavity and ports is very important for DTL RF coupler design.An iris-type coupler is chosen to couple the RF power to the DTL accelerating cavity.The physical design of the DTL coupler and the calculations of RF coupling between the cavity and coupler are carried out.The results from the numerical simulations are in excellent agreement with the analytical results.

  13. Awareness, Preference, Utilization, and Messaging Research for the Spallation Neutron Source and High Flux Isotope Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Bryant, Rebecca [Bryant Research, LLC; Kszos, Lynn A [ORNL

    2011-03-01

    Oak Ridge National Laboratory (ORNL) offers the scientific community unique access to two types of world-class neutron sources at a single site - the Spallation Neutron Source (SNS) and the High Flux Isotope Reactor (HFIR). The 85-MW HFIR provides one of the highest steady-state neutron fluxes of any research reactor in the world, and the SNS is one of the world's most intense pulsed neutron beams. Management of these two resources is the responsibility of the Neutron Sciences Directorate (NScD). NScD commissioned this survey research to develop baseline information regarding awareness of and perceptions about neutron science. Specific areas of investigative interest include the following: (1) awareness levels among those in the scientific community about the two neutron sources that ORNL offers; (2) the level of understanding members of various scientific communities have regarding benefits that neutron scattering techniques offer; and (3) any perceptions that negatively impact utilization of the facilities. NScD leadership identified users of two light sources in North America - the Advanced Photon Source (APS) at Argonne National Laboratory and the National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory - as key publics. Given the type of research in which these scientists engage, they would quite likely benefit from including the neutron techniques available at SNS and HFIR among their scientific investigation tools. The objective of the survey of users of APS, NSLS, SNS, and HFIR was to explore awareness of and perceptions regarding SNS and HFIR among those in selected scientific communities. Perceptions of SNS and FHIR will provide a foundation for strategic communication plan development and for developing key educational messages. The survey was conducted in two phases. The first phase included qualitative methods of (1) key stakeholder meetings; (2) online interviews with user administrators of APS and NSLS; and (3) one

  14. Design of a horizontal neutron reflectometer for the European Spallation Source

    Science.gov (United States)

    Nekrassov, D.; Trapp, M.; Lieutenant, K.; Moulin, J.-F.; Strobl, M.; Steitz, R.

    2014-08-01

    A design study of a horizontal neutron reflectometer adapted to the general baseline of the long pulse European Spallation Source (ESS) is presented. The instrument layout comprises advanced solutions for the neutron guide, high-resolution pulse shaping and beam bending onto a sample surface being thoroughly adjusted to the properties of the ESS. The length of this instrument is roughly 55 m, enabling δλ/λ resolutions from 0.5% to 10%. The incident beam is focused in horizontal plane to boost measurements of sample sizes of 1×1 cm2 and smaller with potential beam deflection in both downward and upward directions. The primary range of neutron wavelengths utilized by the instrument is 2-7.1 Å. If the wavelength range needs to be extended, then this is possible by utilizing only every second (third, fourth) pulse by suppressing all other pulses by the chopper system and thus increase the longest usable wavelength to 12.2 (17.3, 22.4) Å. Angles of incidence can be set between 0° and 9° with a total accessible q-range from 4×10-3 Å-1 up to 1 Å-1, while the δθ/θ resolution can be freely set. The instrument operates in both θ/θ (free liquid surfaces) and θ/2θ (solid-liquid, air-solid interfaces) geometries. The experimental setup will in particular enable direct studies on ultrathin films (d ≈10 Å) and buried monolayers to multilayered structures of up to 3000 Å total thickness. The horizontal reflectometer will further foster investigations of hierarchical systems from nanometer to micrometer length scale (the latter by off-specular scattering), as well as their kinetics and dynamical properties, in particular under load (shear, pressure, external fields). Polarization and polarization analysis as well as the GISANS option are designed as potential modules to be implemented in the generic instrument layout. The instrument is highly flexible and offers a variety of different measurement modes. With respect to its mechanical components the instrument

  15. Comparison of different antenna designs in the spallation neutron source negative hydrogen ion source

    Science.gov (United States)

    Veitzer, Seth A.; Kundrapu, Madhusudhan; Stoltz, Peter H.; Beckwith, Kristian R. C.

    2017-08-01

    Internal antenna negative hydrogen ion sources can fail when plasma heating causes ablation of the insulating coating due to small structural defects such as cracks. During this process, plasma ions impacting the surfaces of rf antennas causes heating of the coating, which can melt or ablate, thus exposing conducting surfaces to the plasma. Reducing antenna failures that reduce the operating capabilities of the Spallation Neutron Source (SNS) accelerator has been one of the top priorities of the SNS H-Source Program at ORNL. We have been utilizing numerical modeling of internal antenna negative hydrogen ion sources in order help optimize antenna designs in order to reduce antenna failures. We have implemented a number of fluid models with electromagnetics using the simulation tool USim and applied them to modeling the SNS internal antenna negative ion source. We report here on results comparing two different antenna designs. The baseline design, as is currently in use in the SNS source, and a wide-leg design, that has been tested, and may replace the baseline design if it can reduce antenna failures while still maintaining source performance. The wide-leg antenna is designed to move the antenna supports out of the high-density plasma regions, in order to decrease the possible negative effects of ion bombardment. We model the plasma evolution using a single-fluid MHD model with an imposed magnetic field due to the rf antenna current and the confining multi-cusp field for both the baseline and wide-leg antenna configurations. We find that the maximum plasma velocity near the antenna surfaces is reduced by nearly 50% in the wide-leg configuration, and that overall the bulk plasma velocity is reduced for this configuration. In addition, although we measure a small increase in the maximum plasma flux on the antenna surface for the wide-leg design, we see a broad-based reduction of plasma flux on the antenna in the regions where the antenna is mostly exposed to the

  16. Experimental and numerical investigation of liquid-metal free-surface flows in spallation targets

    Energy Technology Data Exchange (ETDEWEB)

    Batta, A., E-mail: batta@kit.edu [Karlsruhe Institute of Technology, Germany Hermann-von-Helmholtz-PLATZ 1, 76344 Eggenstein-Leopoldshafen (Germany); Class, A.G.; Litfin, K.; Wetzel, Th. [Karlsruhe Institute of Technology, Germany Hermann-von-Helmholtz-PLATZ 1, 76344 Eggenstein-Leopoldshafen (Germany); Moreau, V.; Massidda, L. [CRS4 Centre for Advanced Studies, Research and Development in Sardinia, Polaris, Edificio 1, 09010 Pula, CA (Italy); Thomas, S.; Lakehal, D. [ASCOMP GmbH Zurich, Zurich (Switzerland); Angeli, D.; Losi, G. [DIEF – Department of Engineering “Enzo Ferrari”, University of Modena and Reggio Emilia, via Vignolese 905, 41125 Modena (Italy); Mooney, K.G. [University of Massachusetts Amherst, Department of Mechanical and Industrial Engineering, Amherst (United States); Van Tichelen, K. [SCK-CEN, Belgian Nuclear Research Centre, Boeretang 200, 2400 Mol (Belgium)

    2015-08-15

    Highlights: • Experimental study of free surface for lead bismuth eutectic target. • Numerical investigation of free surface of a liquid metal target. • Advanced free surface modelling. - Abstract: Accelerator Driven Systems (ADS) are extensively investigated for the transmutation of high-level nuclear waste within many worldwide research programs. The first advanced design of an ADS system is currently developed in SCK• CEN, Mol, Belgium: the Multi-purpose hYbrid Research Reactor for High-tech Applications (MYRRHA). Many European research programs support the design of MYRRHA. In the framework of the Euratom project ‘Thermal Hydraulics of Innovative nuclear Systems (THINS)’ a liquid-metal free-surface experiment is performed at the Karlsruhe Liquid Metal Laboratory (KALLA) of Karlsruhe Institute of Technology (KIT). The experiment investigates a full-scale model of the concentric free-surface spallation target of MYRRHA using Lead Bismuth Eutectic (LBE) as coolant. In parallel, numerical free surface models are developed and tested which are reviewed in the article. A volume-of-fluid method, a moving mesh model, a free surface model combining the Level-Set method with Large-Eddy Simulation model and a smoothed-particle hydrodynamics approach are investigated. Verification of the tested models is based on the experimental results obtained within the THINS project and on previous water experiments performed at the University Catholic de Louvain (UCL) within the Euratom project ‘EUROpean Research Programme for the TRANSmutation of High Level Nuclear Waste in Accelerator Driven System (EUROTRANS)’. The design of the target enables a high fluid velocity and a stable surface at the beam entry. The purpose of this paper is to present an overview of both experimental and numerical results obtained for free surface target characterization. Without entering in technical details, the status, the major achievements and lessons for the future with respect to

  17. In pursuit of a promise perspectives on the political process to establish the European Spallation Source (ESS) in Lund, Sweden

    CERN Document Server

    2012-01-01

    On 28 May 2009, at a closed meeting in Brussels, ministers and state secretaries of education and science from several EU countries decided to build the European Spallation Source (ESS) in Lund, Sweden. Or did they? It is common for big European science projects to be surrounded by secrecy and political deceit, but the ESS is extraordinary in its elusiveness. There is a remarkable lack of concrete economic, political, technical and scientific underpinnings to the project - but a boasting certainty in the promises of future paybacks. The ESS is an accelerator-based neutron spallation facility that will cost billions of Euros to build and run. It is expected to bring new knowledge in several fields including materials science, energy research, and the life sciences. But its financing is not yet certain, and future returns hard to predict. How then could the decision to build ESS occur? Why was there so little organized resistance? This book places the ESS project in its political and scientific context. It link...

  18. Radiochemical separation of {sup 7}Be from the cooling water of the neutron spallation source SINQ at PSI

    Energy Technology Data Exchange (ETDEWEB)

    Schumann, D.; Stowasser, T. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Ayranov, M. [Commission of the European Communities, Luxembourg (Luxembourg). Directorate General Energy; Gialanella, L. [Seconda Univ. di Napoli, Caserta (Italy). Dipt. di Matematica e Fisica; Istituto Nazionale di Fisica Nucleare, Sezione di Napoli (Italy); Di Leva, A.; Romano, M.; Schuermann, D. [Istituto Nazionale di Fisica Nucleare, Sezione di Napoli (Italy); Universita di Napoli Frederico II (Italy). Dipt. di Fisica

    2013-10-01

    {sup 7}Be is a key radionuclide for investigation of several astrophysical processes and phenomena. In addition, it is used as a tracer in war measurements. It is produced in considerable amounts in the cooling water (D{sub 2}O) of the Spallation Induced Neutron Source (SINQ) facility at PSI by spallation reactions on {sup 16}O with the generated fast neutrons. A shielded ion-exchange filter containing 100 mL of the mixed-bed ion exchanger LEWATIT was installed as a bypass for the cooling water into the cooling loop of SINQ for three months. The collected activity of {sup 7}Be was in the range of several hundred GBq. Further, the {sup 7}Be was separated and purified in a hot-cell remotely-controlled using a separation system installed. With the exception of {sup 10}Be, radioactive by-products can be neglected, so that this cooling water could serve as an ideal source for highly active {sup 7}Be-samples. The facility is capable of producing {sup 7}Be with activities up to 1 TBq per year. The {sup 7}Be sample preparation is described in detail and the possible uses are discussed. In particular some preliminary results of {sup 7}Be ion beam production are presented. (orig.)

  19. Overview of the Conceptual Design of the Future VENUS Neutron Imaging Beam Line at the Spallation Neutron Source

    Science.gov (United States)

    Bilheux, Hassina; Herwig, Ken; Keener, Scott; Davis, Larry

    VENUS (Versatile Neutron Imaging Beam line at the Spallation Neutron Source) will be a world-class neutron-imaging instrument that will uniquely utilize the Spallation Neutron Source (SNS) time-of-flight (TOF) capabilities to measure and characterize objects across several length scales (mm to μm). When completed, VENUS will provide academia, industry and government laboratories with the opportunity to advance scientific research in areas such as energy, materials, additive manufacturing, geosciences, transportation, engineering, plant physiology, biology, etc. It is anticipated that a good portion of the VENUS user community will have a strong engineering/industrial research focus. Installed at Beam line 10 (BL10), VENUS will be a 25-m neutron imaging facility with the capability to fully illuminate (i.e., umbra illumination) a 20 cm x 20 cm detector area. The design allows for a 28 cm x 28 cm field of view when using the penumbra to 80% of the full illumination flux. A sample position at 20 m will be implemented for magnification measurements. The optical components are comprised of a series of selected apertures, T0 and bandwidth choppers, beam scrapers, a fast shutter to limit sample activation, and flight tubes filled with Helium. Techniques such as energy selective, Bragg edge and epithermal imaging will be available at VENUS.

  20. Results from the TARC experiment: spallation neutron phenomenology in lead and neutron-driven nuclear transmutation by adiabatic resonance crossing.

    CERN Document Server

    Abánades, A; Andriamonje, Samuel A; Angelopoulos, Angelos; Apostolakis, Alcibiades J; Arnould, H; Belle, E; Bompas, C A; Brozzi, Delecurgo; Bueno, J; Buono, S; Carminati, F; Casagrande, Federico; Cennini, P; Collar, J I; Cerro, E; Del Moral, R; Díez, S; Dumps, Ludwig; Eleftheriadis, C; Embid, M; Fernández, R; Gálvez, J; García, J; Gelès, C; Giorni, A; González, E; González, O; Goulas, I; Heuer, R D; Hussonnois, M; Kadi, Y; Karaiskos, P; Kitis, G; Klapisch, Robert; Kokkas, P; Lacoste, V; Le Naour, C; Lèpez, C; Loiseaux, J M; Martínez-Val, J M; Méplan, O; Nifenecker, H; Oropesa, J; Papadopoulos, I M; Pavlopoulos, P; Pérez-Enciso, E; Pérez-Navarro, A; Perlado, M; Placci, A; Poza, M; Revol, Jean Pierre Charles; Rubbia, Carlo; Rubio, J A; Sakelliou, L; Saldaña, F; Savvidis, E; Schussler, F; Sirvent, C; Tamarit, J; Trubert, D; Tzima, A; Viano, J B; Vieira, S L; Vlachoudis, V; Zioutas, Konstantin; CERN. Geneva. SPS and LEP Division

    2000-01-01

    The results of the TARC experiment are summarized herewith, whose main purpose is to demonstrate the possibility of using Adiabatic Resonance Crossing (ARC) to destroy efficiently Long-Lived Fission Fragments (LLFFs) in accelerator-driven systems and to validate a new simulation developed in the framework of the Energy Amplifier programme. An experimental set-up was installed in a CERN PS proton beam line to study how neutrons, produced by spallation at relatively high energy (En * 1 MeV), slow down quasi adiabatically, with almost flat isolethargic energy distribution and reach the capture resonance energy of an element to be transmuted where they will have a high probability of being captured. Precision measurements of energy and space distributions of spallation neutrons (using 2.5 GeV/c and 3.5 GeV/c protons) slowing down in a 3.3 m x 3.3 m x 3 m lead volume and of neutron capture rates on LLFFs 99Tc, 129I, and several other elements were performed. An appropriate formalism and appropriate computational t...

  1. Study on bulk shielding for a spallation neutron source facility in the high-intensity proton accelerator project

    CERN Document Server

    Maekawa, F; Takada, H; Teshigawara, M; Watanabe, N

    2002-01-01

    Under the JAERI-KEK High-Intensity Proton Accelerator Project, a spallation neutron source driven by a 3 GeV-1 MW proton beam is planed to be constructed in a main part of the Materials and Life Science Facility. This report describes results of a study on bulk shielding performance of a biological shield for the spallation neutron source by means of a Monte Carlo calculation method, that is important in terms of radiation safety and cost reduction. A shielding configuration was determined as a reference case by considering preliminary studies and interaction with other components, then shielding thickness that was required to achieve a target dose rate of 1 mu Sv/h was derived. Effects of calculation conditions such as shielding materials and dimensions on the shielding performance was investigated by changing those parameters. By taking all the results and design margins into account, a shielding configuration that was identified as the most appropriate was finally determined as follows. An iron shield regi...

  2. European Neutrons form Parasitic Research to Global Strategy: Realizing Plans for a Transnational European Spallation Source in the Wake of the Cold War

    Science.gov (United States)

    Kaiserfeld, Thomas

    2016-03-01

    Studies of Big Science have early on focused on instrumentation and scientific co-operation in large organizations, later on to take into account symbolic values and specific research styles while more recently also involving the relevance of commercial interests and economic development as well as the assimilation of research traditions. In accordance with these transformed practices, this presentation will analyze how an organization with the purpose of realizing a Big-Science facility, The European Spallation Source, has successfully managed to present the project as relevant to different national and international policy-makers, to the community of European neutron researchers as well as to different industrial interests. All this has been achieved in a research-policy environment, which has been the subject to drastic transformations, from calls to engage researchers from the former eastern bloc in the early 1990s via competition with American and Asian researchers at the turn of the century 2000 to intensified demands on business applications. During this process, there has also been fierce competition between different potential sites in the U.K., Germany, Spain, Hungary and Sweden, not once, but twice. The project has in addition been plagued by withdrawals of key actors as well as challenging problems in the field of spallation-source construction. Nevertheless, the European Spallation Source has survived from the early 1990s until today, now initiating the construction process at Lund in southern Sweden. In this presentation, the different measures taken and arguments raised by the European Spallation Source project in order to realize the facility will be analysed. Especially the different designs of the European Spallation Source will be analysed as responses to external demands and threats.

  3. Doubly-Resonant Fabry-Perot Cavity for Power Enhancement of Burst-Mode Picosecond Ultraviolet Pulses

    Energy Technology Data Exchange (ETDEWEB)

    Abudureyimu, Reheman [ORNL; Huang, Chunning [ORNL; Liu, Yun [ORNL

    2015-01-01

    We report on a first experimental demonstration of locking a doubly-resonant Fabry-Perot cavity to burst-mode picosecond ultraviolet (UV) pulses by using a temperature controlled dispersion compensation method. This technique will eventually enable the intra cavity power enhancement of burst-mode 402.5MHz/50ps UV laser pulses with a MW level peak power required for the laser assisted H- beam stripping experiment at the Spallation Neutron Source.

  4. Coherent neutrino-nucleus scattering detection with a CsI[Na] scintillator at the SNS spallation source

    CERN Document Server

    Collar, J I; Fuller, E; Hai, M; Hossbach, T W; Orrell, J L; Perumpilly, G; Scholz, B

    2014-01-01

    We study the possibility of using CsI[Na] scintillators as an advantageous target for the detection of coherent elastic neutrino-nucleus scattering (CENNS), using the neutrino emissions from the SNS spallation source at Oak Ridge National Laboratory. The response of this material to low-energy nuclear recoils like those expected from this process is characterized. Backgrounds are studied using a 2 kg low-background prototype crystal in a dedicated radiation shield. The conclusion is that a planned 14 kg detector should measure approximately 550 CENNS events per year above a demonstrated $\\sim7$ keVnr low-energy threshold, with a signal-to-background ratio sufficient for a first measurement of the CENNS cross-section. The cross-section for the $^{208}$Pb($\

  5. Concept for a time-of-flight Small Angle Neutron Scattering instrument at the European Spallation Source

    Energy Technology Data Exchange (ETDEWEB)

    Jaksch, S. [ESS Design Update Programme – Germany, Forschungszentrum Jülich GmbH, Jülich (Germany); Jülich Centre for Neutron Science at Heinz Maier-Leibnitz Zentrum, Forschungszentrum Jülich GmbH, Garching (Germany); Martin-Rodriguez, D. [ESS Design Update Programme – Germany, Forschungszentrum Jülich GmbH, Jülich (Germany); Jülich Centre for Neutron Science at Heinz Maier-Leibnitz Zentrum, Forschungszentrum Jülich GmbH, Garching (Germany); Neutron Optics and Shielding Group, European Spallation Source AB, Lund (Sweden); Ostermann, A. [Forschungs-Neutronenquelle Heinz Maier-Leibnitz (FRM II) at Heinz Maier-Leibnitz Zentrum, Technische Universität Muünchen, Garching (Germany); Jestin, J. [Laboratoire Léon Brillouin, LLB, CEA—Saclay, Gif sur Yvette cedex (France); Duarte Pinto, S.; Bouwman, W.G. [Faculty of Applied Sciences, Delft University of Technology, Delft (Netherlands); Uher, J. [Amsterdam Scientific Instruments, Amsterdam (Netherlands); Engels, R. [Zentralinstitut für Elektronik (ZEA-2), Forschungszentrum Jülich GmbH, Jülich (Germany); Frielinghaus, H. [ESS Design Update Programme – Germany, Forschungszentrum Jülich GmbH, Jülich (Germany); Jülich Centre for Neutron Science at Heinz Maier-Leibnitz Zentrum, Forschungszentrum Jülich GmbH, Garching (Germany)

    2014-10-21

    A new Small Angle Neutron Scattering instrument is proposed for the European Spallation Source. The pulsed source requires a time-of-flight analysis of the gathered neutrons at the detector. The optimal instrument length is found to be rather large, which allows for a polarizer and a versatile collimation. The polarizer allows for studying magnetic samples and incoherent background subtraction. The wide collimation will host VSANS and SESANS options that increase the resolution of the instrument towards µm and tens of µm, respectively. Two 1 m{sup 2} area detectors will cover a large solid angle simultaneously. The expected gains for this new instrument will lie in the range between 20 and 36, depending on the assessment criteria, when compared to up-to-date reactor based instruments. This will open new perspectives for fast kinetics, weakly scattering samples, and multi-dimensional contrast variation studies.

  6. Hardware Aspects, Modularity and Integration of an Event Mode Data Acquisition and Instrument Control for the European Spallation Source (ESS)

    CERN Document Server

    Gahl, Thomas; Hall-Wilton, Richard; Kolya, Scott; Koennecke, Mark; Rescic, Miha; Rod, Thomas H; Sutton, Iain; Trahern, Garry; Kirstein, Oliver

    2015-01-01

    The European Spallation Source (ESS) in Lund, Sweden is just entering the construction phase with 3 neutron instruments having started in its design concept phase in 2014. As a collaboration of 17 European countries the majority of hardware devices for neutron instrumentation will be provided in-kind. This presents numerous technical and organisational challenges for the construction and the integration of the instruments into the facility wide infrastructure; notably the EPICS control network with standardised hardware interfaces and the facilities absolute timing system. Additionally the new generation of pulsed source requires a new complexity and flexibility of instrumentation to fully exploit its opportunities. In this contribution we present a strategy for the modularity of the instrument hardware with well-defined standardized functionality and control & data interfaces integrating into EPICS and the facilities timing system. It allows for in-kind contribution of dedicated modules for each instrume...

  7. Reference Physics Design for 1 GeV Injector Linac and Accumulator Ring for Indian Spallation Neutron Source

    CERN Document Server

    Sharma, Amalendu; Patidar, Chirag Bhai; Pal, Mukesh Kumar; Kulkarni, Nita; Goyal, Pradeep Kumar; Jana, Prasanta Kumar; Gaur, Rahul; Prakash, Ram; Dhingra, Rinky; Singh, Urmila; Kumar, Vinit

    2016-01-01

    As a part of the ongoing plan project titled 'R&D activities for high energy proton linac based spallation neutron source', the work on physics design of various subsystems of the injector linac and accumulator ring has been taken up. For the 1 GeV H- injector linac, physics design studies of individual systems have been completed, and the end to end beam dynamics simulation studies have been performed to ensure that the stringent beam dynamics criteria are satisfied for the optimized lattice. Physics design studies to optimize the linear lattice of the accumulator ring have also been completed. The design studies for the beam transport lines from the injector linac to the accumulator ring, and from the accumulator ring to target are currently in progress. This report describes the physics design of various systems of the injector linac and the accumulator ring.

  8. Beam commission of the high intensity proton source developed at INFN-LNS for the European Spallation Source

    Science.gov (United States)

    Neri, L.; Celona, L.; Gammino, S.; Miraglia, A.; Leonardi, O.; Castro, G.; Torrisi, G.; Mascali, D.; Mazzaglia, M.; Allegra, L.; Amato, A.; Calabrese, G.; Caruso, A.; Chines, F.; Gallo, G.; Longhitano, A.; Manno, G.; Marletta, S.; Maugeri, A.; Passarello, S.; Pastore, G.; Seminara, A.; Spartà, A.; Vinciguerra, S.

    2017-07-01

    At the Istituto Nazionale di Fisica Nucleare - Laboratori Nazionali del Sud (INFN-LNS) the beam commissioning of the high intensity Proton Source for the European Spallation Source (PS-ESS) started in November 2016. Beam stability at high current intensity is one of the most important parameter for the first steps of the ongoing commissioning. Promising results were obtained since the first source start with a 6 mm diameter extraction hole. The increase of the extraction hole to 8 mm allowed improving PS-ESS performances and obtaining the values required by the ESS accelerator. In this work, extracted beam current characteristics together with Doppler shift and emittance measurements are presented, as well as the description of the next phases before the installation at ESS in Lund.

  9. Simulation of H{sup -} ion source extraction systems for the Spallation Neutron Source with Ion Beam Simulator

    Energy Technology Data Exchange (ETDEWEB)

    Kalvas, T.; Tarvainen, O. [Department of Physics, University of Jyvaeskylae, Jyvaeskylae (Finland); Welton, R. F.; Han, B. X.; Stockli, M. P. [Spallation Neutron Source, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States)

    2012-02-15

    A three-dimensional ion optical code IBSimu, which is being developed at University of Jyvaeskylae, features positive and negative ion plasma extraction models and self-consistent space charge calculation. The code has been utilized for modeling the existing extraction system of the H{sup -} ion source of the Spallation Neutron Source. Simulation results are in good agreement with experimental data. A high-current extraction system with downstream electron dumping at intermediate energy has been designed. According to the simulations it provides lower emittance compared to the baseline system at H{sup -} currents exceeding 40 mA. A magnetic low energy beam transport section consisting of two solenoids has been designed to transport the beam from the alternative electrostatic extraction systems to the radio frequency quadrupole.

  10. Performance of the Los Alamos National Laboratory spallation-driven solid-deuterium ultra-cold neutron source.

    Science.gov (United States)

    Saunders, A; Makela, M; Bagdasarova, Y; Back, H O; Boissevain, J; Broussard, L J; Bowles, T J; Carr, R; Currie, S A; Filippone, B; García, A; Geltenbort, P; Hickerson, K P; Hill, R E; Hoagland, J; Hoedl, S; Holley, A T; Hogan, G; Ito, T M; Lamoreaux, Steve; Liu, Chen-Yu; Liu, J; Mammei, R R; Martin, J; Melconian, D; Mendenhall, M P; Morris, C L; Mortensen, R N; Pattie, R W; Pitt, M; Plaster, B; Ramsey, J; Rios, R; Sallaska, A; Seestrom, S J; Sharapov, E I; Sjue, S; Sondheim, W E; Teasdale, W; Young, A R; VornDick, B; Vogelaar, R B; Wang, Z; Xu, Yanping

    2013-01-01

    In this paper, we describe the performance of the Los Alamos spallation-driven solid-deuterium ultra-cold neutron (UCN) source. Measurements of the cold neutron flux, the very low energy neutron production rate, and the UCN rates and density at the exit from the biological shield are presented and compared to Monte Carlo predictions. The cold neutron rates compare well with predictions from the Monte Carlo code MCNPX and the UCN rates agree with our custom UCN Monte Carlo code. The source is shown to perform as modeled. The maximum delivered UCN density at the exit from the biological shield is 52(9) UCN/cc with a solid deuterium volume of ~1500 cm(3).

  11. Concept for a Time-of-Flight Small Angle Neutron Scattering Instrument at the European Spallation Source

    CERN Document Server

    Jaksch, S; Ostermann, A; Jestin, J; Pinto, S Duarte; Bouwman, W G; Uher, J; Engels, R; Kemmerling, G; Hanslik, R; Frielinghaus, H

    2014-01-01

    A new Small Angle Neutron Scattering instrument is proposed for the European Spallation Source. The pulsed source requires a time-of-flight analysis of the gathered neutrons at the detector. The optimal instrument length is found to be rather large, which allows for a polarizer and a versatile collimation. The polarizer allows for studying magnetic samples and incoherent background subtraction. The wide collimation will host VSANS and SESANS options that increase the resolution of the instrument towards um and tens of um, respectively. Two 1m2 area detectors will cover a large solid angle simultaneously. The expected gains for this new instrument will lie in the range between 20 and 36, depending on the assessment criteria, when compared to up-to-date reactor based instruments. This will open new perspectives for fast kinetics, weakly scattering samples, and multi-dimensional contrast variation studies.

  12. Calculation Package: Derivation of Facility-Specific Derived Air Concentration (DAC) Values in Support of Spallation Neutron Source Operations

    Energy Technology Data Exchange (ETDEWEB)

    McLaughlin, David A [ORNL

    2009-12-01

    Derived air concentration (DAC) values for 175 radionuclides* produced at the Oak Ridge National Laboratory (ORNL) Spallation Neutron Source (SNS), but not listed in Appendix A of 10 CFR 835 (01/01/2009 version), are presented. The proposed DAC values, ranging between 1 E-07 {micro}Ci/mL and 2 E-03 {micro}Ci/mL, were calculated in accordance with the recommendations of the International Commission on Radiological Protection (ICRP), and are intended to support an exemption request seeking regulatory relief from the 10 CFR 835, Appendix A, requirement to apply restrictive DACs of 2E-13 {micro}Ci/mL and 4E-11 {micro}Ci/mL and for non-listed alpha and non-alpha-emitting radionuclides, respectively.

  13. Lithium Production in Companions of Accreting X-Ray Binaries by Neutron Spallation of C, N, O Elements

    CERN Document Server

    Guessoum, N; Guessoum, Nidhal; Kazanas, Demosthenes

    1999-01-01

    We examine the processes which could lead to the observed enhancement of Li and possibly other light elements (Be, B) in the companions of a number of X-ray novae. We conclude that one of the most promising mechanisms is the spallation of CNO elements on the surface of the companion induced by the neutron flux produced in the hot accretion flow onto the compact object. Direct production of the observed Li and its deposition onto the dwarf companion seem less likely, mainly because of the possibility of its destruction in the production region itself and difficulties in its deposition associated with the configuration of the companion's magnetic field. We discuss other potential observables of the above scenario.

  14. Calculation Package: Derivation of Facility-Specific Derived Air Concentration (DAC) Values in Support of Spallation Neutron Source Operations

    Energy Technology Data Exchange (ETDEWEB)

    McLaughlin, David A [ORNL

    2009-12-01

    Derived air concentration (DAC) values for 175 radionuclides* produced at the Oak Ridge National Laboratory (ORNL) Spallation Neutron Source (SNS), but not listed in Appendix A of 10 CFR 835 (01/01/2009 version), are presented. The proposed DAC values, ranging between 1 E-07 {micro}Ci/mL and 2 E-03 {micro}Ci/mL, were calculated in accordance with the recommendations of the International Commission on Radiological Protection (ICRP), and are intended to support an exemption request seeking regulatory relief from the 10 CFR 835, Appendix A, requirement to apply restrictive DACs of 2E-13 {micro}Ci/mL and 4E-11 {micro}Ci/mL and for non-listed alpha and non-alpha-emitting radionuclides, respectively.

  15. The future plan for the applications of RI produced in the proton-induced spallation-reaction

    Energy Technology Data Exchange (ETDEWEB)

    Ikezoe, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-07-01

    A plan of research facilities (transmutations of minor actinides and neutron scattering for material and life sciences) has been proposed in JAERI. This plan is based on a proton lineac with an energy of 1.5 GeV and a beam current of several mA. Among these facilities, we are planning to accelerate neutron-rich radioactive nuclei (RI) produced in the fission and spallation reactions of thorium or uranium bombarded by the intense high energy proton beams. The RI produced in an ion source are separated by a high resolution isotope separator and their charge states are changed to be negative to inject into the existing tandem-booster accelerator. Main purpose of this plan is to study the nuclear and chemical properties of neutron rich transactinium elements not yet synthesized and the nuclear structures of neutron rich nuclei far from the nuclear stability line. (author)

  16. The MEGAPIE-TEST project: Supporting research and lessons learned in first-of-a-kind spallation target technology

    Energy Technology Data Exchange (ETDEWEB)

    Fazio, C. [Forschungszentrum Karlsruhe GmbH, P.O. Box 3640, 76021 Karlsruhe (Germany)], E-mail: concetta.fazio@nuklear.fzk.de; Groeschel, F.; Wagner, W.; Thomsen, K.; Smith, B.L. [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland); Stieglitz, R. [Forschungszentrum Karlsruhe GmbH, P.O. Box 3640, 76021 Karlsruhe (Germany); Zanini, L. [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland); Guertin, A.; Cadiou, A. [SUBATECH Laboratory, CNRS/IN2P3-EMN-University, F-44307 Nantes (France); Henry, J. [Commissariat a l' energie atomique, 91191 Gif-sur-Yvette Cedex (France); Agostini, P. [Ente per le nuove Tecnologie, l' Energia e l' Ambiente, Localita Brasimone, 40032 Camugnano, Bologna (Italy); Dai, Y.; Heyck, H.; Dementjev, S. [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland); Panebianco, S. [Commissariat a l' energie atomique, 91191 Gif-sur-Yvette Cedex (France); Almazouzi, A. [Studiecentrum voor Kernenergie/Centre d' Etude de l' Energie Nucleaire, Boeretang 200, 2400 Mol (Belgium); Eikenberg, J. [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland); Letourneau, A.; Toussaint, J.C. [Commissariat a l' energie atomique, 91191 Gif-sur-Yvette Cedex (France); Janett, A. [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland)] (and others)

    2008-06-15

    The megawatt pilot experiment (MEGAPIE) has been launched by six European institutions (PSI, FZK, CEA, SCK-CEN, ENEA and CNRS), JAEA (Japan), DOE (US) and KAERI (Korea) with the aim to carry out an experiment, in the SINQ target location at PSI (Switzerland), to demonstrate the safe operation of a liquid metal (lead-bismuth eutectic, LBE) spallation target hit by a {approx}1 MW proton beam. The European Commission has joined the MEGAPIE project through the 5-year (2001-2006) project named MEGAPIE-TEST. This project has been formally concluded with an International Workshop, where the results and the lessons learned during the project have been summarised. This work presents a review of the outcome of that Workshop.

  17. Basic design of shield blocks for a spallation neutron source under the high-intensity proton accelerator project

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Katsuhiko; Maekawa, Fujio; Takada, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2003-03-01

    Under the JAERI-KEK High-Intensity Proton Accelerator Project (J-PARC), a spallation neutron source driven by a 3 GeV-1 MW proton beam is planed to be constructed as a main part of the Materials and Life Science Facility. Overall dimensions of a biological shield of the neutron source had been determined by evaluation of shielding performance by Monte Carlo calculations. This report describes results of design studies on an optimum dividing scheme in terms of cost and treatment and mechanical strength of shield blocks for the biological shield. As for mechanical strength, it was studied whether the shield blocks would be stable, fall down or move to a horizontal direction in case of an earthquake of seismic intensity of 5.5 (250 Gal) as an abnormal load. For ceiling shielding blocks being supported by both ends of the long blocks, maximum bending moment and an amount of maximum deflection of their center were evaluated. (author)

  18. Diagnosis on line and off line of induction motors of low, medium and high voltage; Diagnostico en linea y fuera de linea de motores de induccion de baja, mediana y alta tension

    Energy Technology Data Exchange (ETDEWEB)

    Carvajal, Francisco Antonio; Ramirez, Jose Manuel; Arcos, Luis Fernando [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)

    1999-07-01

    The induction motors of low, medium and high voltage are the electrical equipment of greatest application in industry. The importance which they have in the different productive processes does necessary to assure its operative continuity. The anticipated detection of a possible cause of fault allows to plan, with maintenance aims, the programmed removal of the motor. In this article are presented the results of the activities nowadays performed by Management of Electrical Equipment of the Instituto de Investigaciones Electricas (IIE) for the development and application of online diagnosis techniques for induction motors up to 13.8 kV. [Spanish] Los motores de induccion de baja, mediana y alta tension son los equipos eletricos de mayor aplicacion en la industria. La importancia que tienen en los diferentes procesos productivos hace necesario asegurar su continuidad operativa. La deteccion anticipada de una posible causa de falla permite planear, con fines de mantenimiento, la remocion programada del motor. En este articulo se presentan los resultados de las actividades que realiza actualmente la Gerencia de equipos Electricos del Instituto de investigaciones Electricas (IIE) para el desarrollo y la aplicacion de tecnicas de diagnostico en linea para motores de induccion de hasta 13.8 kV.

  19. Results from the TARC experiment: spallation neutron phenomenology in lead and neutron-driven nuclear transmutation by adiabatic resonance crossing

    Energy Technology Data Exchange (ETDEWEB)

    Abanades, A.; Aleixandre, J.; Andriamonje, S.; Angelopoulos, A.; Apostolakis, A.; Arnould, H.; Belle, E.; Bompas, C.A.; Brozzi, D.; Bueno, J.; Buono, S.; Carminati, F.; Casagrande, F.; Cennini, P.; Collar, J.I.; Cerro, E.; Moral, R. Del; Diez, S.; Dumps, L.; Eleftheriadis, C.; Embid, M.; Fernandez, R.; Galvez, J.; Garcia, J.; Geles, C.; Giorni, A.; Gonzalez, E.; Gonzalez, O.; Goulas, I.; Heuer, D.; Hussonnois, M.; Kadi, Y.; Karaiskos, P.; Kitis, G.; Klapisch, R.; Kokkas, P.; Lacoste, V.; Naour, C. Le; Lopez, C.; Loiseaux, J.M.; Martinez-Val, J.M.; Meplan, O.; Nifenecker, H.; Oropesa, J.; Papadopoulos, I.; Pavlopoulos, P.; Perez-Enciso, E.; Perez-Navarro, A.; Perlado, M.; Placci, A.; Poza, M.; Revol, J.-P. E-mail: jean-pierre.revol@cern.ch; Rubbia, C.; Rubio, J.A.; Sakelliou, L.; Saldana, F.; Savvidis, E.; Schussler, F.; Sirvent, C.; Tamarit, J.; Trubert, D.; Tzima, A.; Viano, J.B.; Vieira, S.; Vlachoudis, V.; Zioutas, K

    2002-02-11

    We summarize here the results of the TARC experiment whose main purpose is to demonstrate the possibility of using Adiabatic Resonance Crossing (ARC) to destroy efficiently Long-Lived Fission Fragments (LLFFs) in accelerator-driven systems and to validate a new simulation developed in the framework of the Energy Amplifier programme. An experimental set-up was installed in a CERN PS proton beam line to study how neutrons produced by spallation at relatively high energy (E{sub n}{>=}1 MeV) slow down quasi-adiabatically with almost flat isolethargic energy distribution and reach the capture resonance energy of an element to be transmuted where they will have a high probability of being captured. Precision measurements of energy and space distributions of spallation neutrons (using 2.5 and 3.5 GeV/c protons) slowing down in a 3.3 mx3.3 mx3 m lead volume and of neutron capture rates on LLFFs {sup 99}Tc, {sup 129}I, and several other elements were performed. An appropriate formalism and appropriate computational tools necessary for the analysis and understanding of the data were developed and validated in detail. Our direct experimental observation of ARC demonstrates the possibility to destroy, in a parasitic mode, outside the Energy Amplifier core, large amounts of {sup 99}Tc or {sup 129}I at a rate exceeding the production rate, thereby making it practical to reduce correspondingly the existing stockpile of LLFFs. In addition, TARC opens up new possibilities for radioactive isotope production as an alternative to nuclear reactors, in particular for medical applications, as well as new possibilities for neutron research and industrial applications.

  20. Protection Related to High-power Targets

    CERN Document Server

    Plum, M.A.

    2016-01-01

    Target protection is an important part of machine protection. The beam power in high-intensity accelerators is high enough that a single wayward pulse can cause serious damage. Today's high-power targets operate at the limit of available technology, and are designed for a very narrow range of beam parameters. If the beam pulse is too far off centre, or if the beam size is not correct, or if the beam density is too high, the target can be seriously damaged. We will start with a brief introduction to high-power targets and then move to a discussion of what can go wrong, and what are the risks. Next we will discuss how to control the beam-related risk, followed by examples from a few different accelerator facilities. We will finish with a detailed example of the Oak Ridge Spallation Neutron Source target tune up and target protection.

  1. Cross section measurements of the yield of spallation reactions related to the study of hybrid reactor systems; Measures de sections efficaces de production de produits de reactions en rapport avec l`etude de systemes de reacteurs hybrides

    Energy Technology Data Exchange (ETDEWEB)

    Bernas, M.; Mustapha, B.; Stephan, C. [Experimental Research Division, Inst. de Physique Nucleaire, Paris-11 Univ., 91 - Orsay (France)] [and others

    1999-11-01

    Studies presently developed on the design of hybrid systems need the knowledge of spallation products and their production rate. To obtain this information we have performed cross-section measurements using the inverse kinematical method. (authors) 2 figs.

  2. Analysis of the spallation residues and the associated particles in the reaction Fe+p at 1 GeV per nucleon; Analyse des residus de spallation et des particules associees dans la reaction Fe+p a 1 GeV par nucleon

    Energy Technology Data Exchange (ETDEWEB)

    Le Gentil, E

    2006-09-15

    SPALADIN is a new type of spallation experiment that has been carried out at the GSI accelerator facility (Germany) in order to improve the modelling of the spallation reaction. This experiment is based on the coincidence measurement in inverse kinematics of the spallation residues and the de-excitation fragments. This work presents the analysis of Fe{sup 56} + p reaction at 1 GeV per nucleon. Results on cross-sections and heavy residue velocity spectra are compared to previous data and enabled us to characterize the setup. Most of the element production cross-sections have been obtained with an uncertainty below 10 per cent. In the particular case of helium, its production cross-section has been measured to be {sigma}(1 GeV) = (598 {+-} 67) mb. The knowledge of this cross-section is important to assess the irradiation damage undergone by the window separating the accelerator from the target. The study of the de-excitation of the pre-fragment shows that the evaporation of light particles (Z {<=} 2) is the main way of de-excitation whatever the collision centrality. However, the de-excitation through the emission of intermediate mass fragments is observed in 5% of the events and most of these events correspond to a very asymmetric binary breaking. The velocity distributions of light residues (with regards to the mass of the projectile) show a significant disagreement with the average velocities predicted by spallation codes. (A.C.)

  3. Topical report on a preconceptual design for the Spallation-Induced Lithium Conversion (SILC) target for the accelerator production of tritium (APT)

    Energy Technology Data Exchange (ETDEWEB)

    Van Tuyle, G.J.; Cokinos, D.M.; Czajkowski, C.; Franz, E.M.; Kroeger, P.; Todosow, M.; Youngblood, R.; Zucker, M.

    1993-09-30

    The preconceptual design of the APT Li-Al target system, also referred to as the Spallation-Induced Lithium Conversion (SILC), target system, is summarized in this report. The system has been designed to produce a ``3/8 Goal`` quantity of tritium using the 200-mA, 1.0 GeV proton beam emerging from the LANL-designed LINAC. The SILC target system consists of a beam expander, a heavy-water-cooled lead spallation neutron source assembly surrounded by light-water-cooled Li-Al blankets, a target window, heat removal systems, and related safety systems. The preconceptual design of each of these major components is described. Descriptions are also provided for the target fabrication, tritium extraction, and waste-steam processes. Performance characteristics are presented and discussed.

  4. Measurement of neutron-induced activation cross-sections using spallation source at JINR and neutronic validation of the Dubna code

    Indian Academy of Sciences (India)

    Manish Sharma; V Kumar; H Kumawat; J Adam; V S Barashenkov; S Ganesan; S Golovatiouk; S K Gupta; S Kailas; M I Krivopustov; H S Palsania; V Pronskikh; V M Tsoupko-Sitnikov; N Vladimirova; H Westmeier; W Westmeier

    2007-02-01

    A beam of 1 GeV proton coming from Dubna Nuclotron colliding with a lead target surrounded by 6 cm paraffin produces spallation neutrons. A Th-foil was kept on lead target (neutron spallation source) in a direct stream of neutrons for activation and other samples of 197Au, 209Bi, 59Co, 115In and 181Ta were irradiated by moderated beam of neutrons passing through 6 cm paraffin moderator. The gamma spectra of irradiated samples were analyzed using gamma spectrometry and DEIMOS software to measure the neutron cross-section. For this purpose neutron fluence at the positions of samples is also estimated using PREPRO software. The results of cross-sections for reactions 232Th(, ), 232Th(, 2), 197Au(, ), 197Au(, ), 197Au(, ), 59Co(, ), 59Co(, ), 181Ta(, ) and 181Ta(, ) are given in this paper. Neutronics validation of the Dubna Cascade Code is also done using cross-section data by other experiments.

  5. Measurement of the spallation reaction {sup 56}Fe+p in inverse kinematics; Messung der Spallationsreaktion {sup 56}Fe+p in inverser Kinematik

    Energy Technology Data Exchange (ETDEWEB)

    Boehmer, M.

    2006-09-25

    In this work the spallation reaction {sup 56}Fe+p was investigated in inverse kinematics with regard to complete identification of the heavy residues. A ring imaging Cerenkov counter was used for velocity measurements in the experimental setup located at GSI in Darmstadt. A new fast readout electronic was developed and has been operated successfully in the experiment. Momentum reconstruction was carried out with the ALADiN spectrometer and a new software package written for this purpose. Cross sections and velocity distributions for more than 100 mass separated isotopes could be extracted from the dataset and compared with empirical models and other spallation experiments. The experiences gained in this experiment will be used for systematic improvements in the setup of the new spectrometer R3B at FAIR. (orig.)

  6. Accumulation of the $^{178m2}Hf$ Isomeric Nuclei Through Spallation with Intermediate-Energy Protons of Tantalum and Rhenium Targets

    CERN Document Server

    Karamian, S A; Adam, J; Filossofov, D V; Henzlova, D; Henzl, V; Kalinnikov, V G; Lebedev, N A; Novgorodov, A F; Collins, C B; Popescu, I I; Ur, C A

    2001-01-01

    The productivity of the spallation reactions at proton energies of 100-660 MeV for accumulation of the radioactive isotopes and isomers has been studied experimentally. Spectra of Ta and Re targets activated at Dubna synchrocyclotron were measured using the methods of radiochemistry and gamma-spectroscopy. Many radioactive products of the spallation and fission reactions are identified, and their yields are compared with the LAHET code simulations. Cross sections, \\sigma_m and isomer-to-ground state ratios, \\sigma_m/\\sigma_g are deduced for nuclear isomers, in particular, for high-spin isomers, as ^{179m2}Hf, ^{179m2}Hf and ^{177m2}Lu. Spin distributions for the spallation-residue nuclei are estimated to understand the \\sigma_m/\\sigma_g ratios. Possibilities to optimize the methods for the long-lived isomers production are discussed, and it would be a necessary step on the way to accumulate such exotic radionuclides in milligram amount under reasonable cost and radiation safety conditions.

  7. Design of an experimental device dedicated to the measurement of spallation reactions; Mise au point d'un dispositif experimental pour des mesures exclusives des reactions de spallation

    Energy Technology Data Exchange (ETDEWEB)

    Lafriakh, A

    2005-12-15

    Spallation mechanisms are not yet completely understood, especially because of the difficulty of experimentally disentangling the effects of the different steps of the reaction. In order to understand these mechanisms, we have developed a new experimental device able to perform inclusive measurements. We propose a detection system based on a combination of ionization chambers and proportional counters and on a wall of plastic scintillators to measure light charged particles. In particular the detection of light charged particles is described in detail. In order to validate our device, we have compared our preliminary results obtained on the Fe{sup 56} + p system at 1 GeV/u with inclusive measurements previously obtained at the FRS spectrometer of the GSI facility. A comparison of charge differential cross section shows reasonable agreement. However, our new device allowed extension of those measurements down to Z = 1 and Z = 2. These cross sections are important for material damage studies. Taking into account our error brackets, the evolution of mean longitudinal velocities with respect to residue masses is comparable to that obtained at the FRS. These first results, although preliminary, allow us to validate our experimental device. It is now possible to exploit the strong points of our exclusive measurements, namely correlations between different measured observables. Finally, experimental problems encountered will be taken into account in the future experimental programs, in order to ensure the best measurements conditions.

  8. Dynamic properties of power MOS transistors

    Science.gov (United States)

    Belabadia, Mohammed

    Power MOSFET's were modeled in dynamic high frequency and switching regimes, based on a theoretical analysis of the active region, taking into account the short channel effects and those related to structural configuration elements. The theoretical synthesis of intrinsic and parasitic elements leads to a complete nonlinear physical model compatible with electric simulators. The model is used for simulation and computer aided design of electric circuits which use power MOSFET's such as RF amplifiers, and frequency doublers. For the switching regime, a hierarchy of models for power V.DMOS transistors is developed. Two compact models consistent with SPICE-2 program and well suited for study and characterization of power V.DMOSFET, in switching condition under resistive and inductive loads, are proposed. They can describe low, medium, and high voltage structures.

  9. VERITAS: a high-flux neutron reflectometer with vertical sample geometry for a long pulse spallation source

    Science.gov (United States)

    Mattauch, S.; Ioffe, A.; Lott, D.; Menelle, A.; Ott, F.; Medic, Z.

    2016-04-01

    An instrument concept of a reflectometer with a vertical sample geometry fitted to the long pulse structure of a spallation source, called “VERITAS” at the ESS, is presented. It focuses on designing a reflectometer with high intensity at the lowest possible background following the users' demand to investigate thin layers or interfacial areas in the sub-nanometer length scale. The high intensity approach of the vertical reflectometer fits very well to the long pulse structure of the ESS. Its main goal is to deliver as much usable intensity as possible at the sample position and be able to access a reflectivity range of 8 orders of magnitude and more. The concept assures that the reflectivity measurements can be performed in its best way to maximize the flux delivered to the sample. The reflectometer is optimized for studies of (magnetic) layers having thicknesses down to 5Å and a surface area of 1x1cm2. With reflectivity measurements the depth-resolved, laterally averaged chemical and magnetic profile can be investigated. By using polarised neutrons, additional vector information on the in-plane magnetic correlations (off-specular scattering at the pm length scale, GISANS at the nm length scale) can be studied. The full polarisation analysis could be used for soft matter samples to correct for incoherent scattering which is presently limiting neutron reflectivity studies to a reflectivity range on the order of 10-6.

  10. Novel Heat Transfer Issues Associated with the Design and Safe Operation of the MEGAPIE Spallation Source Target

    Institute of Scientific and Technical Information of China (English)

    Brian L.Smith

    2007-01-01

    Critical heat transfer problems are discussed in the context of the operation of a spallation source target, which represents a first demonstration of the feasibility of an innovative concept for generating energy using a particle accelerator. Within the framework of the umbrella project MEGAPIE, an R&D support group was organized to take responsibility for target cooling. This involved the use of advanced numerical methods - Computational Fluid Dynamics (CFD) and Finite Element Method (FEM) - validated against suitable experimental data, and by means of appropriate benchmarking exercises. The design studies using CFD resulted in an optimum flow configuration being defined for the coolant circulation. Flow visualization tests were undertaken using a glass/water test section, with the velocity field mapped using optical and ultrasonic measuring techniques. These were followed by heat transfer tests, using the actual target materials (lead-bismuth-eutectic coolant and steel confinement). Further CFD/FEM work to analyze operational transients and accident sequences was also carried out, and is described in the paper.

  11. Development of the DCHAIN-SP code for analyzing decay and build-up characteristics of spallation products

    Energy Technology Data Exchange (ETDEWEB)

    Takada, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kosako, Kazuaki

    1999-03-01

    For analyzing the decay and build-up characteristics of spallation products, the DCHAIN-SP code has been developed on the basis of the DCHAIN-2 code by revising the decay data and implementing the neutron cross section data. The decay data are newly processed from the data libraries of EAF 3.1, FENDL/D-1 and ENSDF. The neutron cross section data taken from FENDL/A-2 data library are also prepared to take account of the transmutation of nuclides by the neutron field at the produced position. The DCHAIN-SP code solves the time evolution of decay and build-up of nuclides in every decay chain by the Beteman method. The code can estimate the following physical quantities of produced nuclides: inventory, activity, decay heat by the emission of {alpha}, {beta} and {gamma}-rays, and {gamma}-ray energy spectrum, where the nuclide production rate estimated by the nucleon-meson transport code such as NMTC/JAERI97 is used as an input data. This paper describes about the function, the solution model and the database adopted in the code and explains how to use the code. (author)

  12. 3-dimensional shielding design for a spallation neutron source facility in the high-intensity proton accelerator project

    Energy Technology Data Exchange (ETDEWEB)

    Tamura, Masaya; Maekawa, Fujio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2003-03-01

    Evaluation of shielding performance for a 1 MW spallation neutron source facility in the Materials and Life Science Facility being constructed in the High-Intensity Proton Accelerator Project (J-PARC) is important from a viewpoint of radiation safety and optimization of arrangement of components. This report describes evaluated results for the shielding performance with modeling three-dimensionally whole structural components including gaps between them in detail. A Monte Carlo calculation method with MCNPX2.2.6 code and LA-150 library was adopted. Streaming and void effects, optimization of shield for cost reduction and optimization of arrangement of structures such as shutters were investigated. The streaming effects were investigated quantitatively by changing the detailed structure of components and gap widths built into the calculation model. Horizontal required shield thicknesses were ranged from about 6.5 m to 7.5 m as a function of neutron beam line angles. A shutter mechanism for a horizontal neutron reflectometer that was directed downward was devised, and it was shown that the shielding performance of the shutter was acceptable. An optimal biological shield configuration was finally determined according to the calculated results. (author)

  13. Preliminary Assessment of the Nuclide Migration from the Activation Zone Around the Proposed Spallation Neutron Source Facility

    Energy Technology Data Exchange (ETDEWEB)

    Dole, L.R.

    1998-09-01

    The purpose of this study is to investigate the potential impacts of migrating radionuclides from the activation zone around the proposed Spallation Neutron Source (SNS). Using conservatively high estimates of the potential inventory of radioactive activation products that could form in the proposed compacted-soil shield berm around an SNS facility on the Oak Ridge Reservation (ORR), a conservative, simplified transport model was used to estimate the potential worst-case concentrations of the 12 long-lived isotopes in the groundwater under a site with the hydrologic characteristics of the ORR. Of the 12, only 3 isotopes showed any potential to exceed the U.S. Nuclear Regulatory Commission (NRC) 10 Code of Federal Regulations (CFR) Part 20 Drinking Water Limits (DWLs). These isotopes were 14C, 22Na, and 54Mn. The latter two activation products have very short half-lives of 2.6 years and 0.854 year, respectively. Therefore, these will decay before reaching an off-site receptor, and they cannot pose off-site hazards. However, for this extremely conservative model, which overestimates the mobility of the contaminant, 14C, which has a 5,730-year half-life, was shown to represent a potential concern in the context of this study's conservative assumptions. This study examines alternative modifications to the SNS shield berm and makes recommendations.

  14. First measurement of radioactive isotope production through cosmic-ray muon spallation in Super-Kamiokande IV

    CERN Document Server

    ,

    2016-01-01

    Cosmic-ray-muon spallation-induced radioactive isotopes with $\\beta$ decays are one of the major backgrounds for solar, reactor, and supernova relic neutrino experiments. Unlike in scintillator, production yields for cosmogenic backgrounds in water have not been exclusively measured before, yet they are becoming more and more important in next generation neutrino experiments designed to search for rare signals. We have analyzed the low-energy trigger data collected at Super-Kamiokande-IV in order to determine the production rates of $^{12}$B, $^{12}$N, $^{16}$N, $^{11}$Be, $^9$Li, $^8$He, $^9$C, $^8$Li, $^8$B and $^{15}$C. These rates were extracted from fits to time differences between parent muons and subsequent daughter $\\beta$'s by fixing the known isotope lifetimes. Since $^9$Li can fake an inverse-beta-decay reaction chain via a $\\beta + n$ cascade decay, producing an irreducible background with detected energy up to a dozen MeV, a dedicated study is needed for evaluating its impact on future measuremen...

  15. Neutron-induced transmutation reactions in 237Np, 238Pu, and 239Pu at the massive natural uranium spallation target

    Science.gov (United States)

    Zavorka, L.; Adam, J.; Baldin, A. A.; Caloun, P.; Chilap, V. V.; Furman, W. I.; Kadykov, M. G.; Khushvaktov, J.; Pronskikh, V. S.; Solnyshkin, A. A.; Sotnikov, V.; Stegailov, V. I.; Suchopar, M.; Tsoupko-Sitnikov, V. M.; Tyutyunnikov, S. I.; Voronko, V.; Vrzalova, J.

    2015-04-01

    Transmutation reactions in the 237Np, 238Pu, and 239Pu samples were investigated in the neutron field generated inside a massive (m = 512 kg) natural uranium spallation target. The uranium target assembly QUINTA was irradiated with the deuteron beams of kinetic energy 2, 4, and 8 GeV provided by the Nuclotron accelerator at the Joint Institute for Nuclear Research (JINR) in Dubna. The neutron-induced transmutation of the actinide samples was measured off-line by implementing methods of gamma-ray spectrometry with HPGe detectors. Results of measurement are expressed in the form of both the individual reaction rates and average fission transmutation rates. For the purpose of validation of radiation transport programs, the experimental results were compared with simulations of neutron production and distribution performed by the MCNPX 2.7 and MARS15 codes employing the INCL4-ABLA physics models and LAQGSM event generator, respectively. In general, a good agreement between the experimental and calculated reaction rates was found in the whole interval of provided beam energies.

  16. EFFECT OF SURFACE CONDITION ON SPALLATION BEHAVIOR OF OXIDE SCALE ON SS 441 SUBSTRATE USED IN SOFC

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Wenning N.; Sun, Xin; Stephens, Elizabeth V.; Khaleel, Mohammad A.

    2011-03-01

    As operating temperature of SOFC decreases, ferritic stainless steel has attracted a great deal of attention for its use as an interconnect in SOFCs because of its gas-tightness, low electrical resistivity, ease of fabrication, and cost-effectiveness. However, oxidation reaction of the metallic interconnects in a typical SOFC working environment is unavoidable. The growth stresses in the oxide scale and on the scale/substrate interface combined with the thermal stresses induced by thermal expansion coefficient mismatch between the oxide scale and the substrate may lead to scale delamination/buckling and eventual spallation during stack cooling, which can lead to serious cell performance degradation. Therefore, the interfacial adhesion strength between the oxide scale and substrate is crucial to the reliability and durability of the metallic interconnect in SOFC operating environments. In this paper, we investigated the effect of the surface conditions on the interfacial strength of oxide scale and SS441 substrate experimentally. Contrary to the conventional sense, it was found that rough surface of SS441 substrate will decrease the interfacial adhesive strength of the oxide scale and SS441 substrate

  17. Improvements to the internal and external antenna H{sup −} ion sources at the Spallation Neutron Source

    Energy Technology Data Exchange (ETDEWEB)

    Welton, R. F., E-mail: welton@ornl.gov; Han, B. X.; Murray, S. N.; Pennisi, T. R.; Pillar, C.; Santana, M.; Stockli, M. P. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, Tennessee 37830-6471 (United States); Dudnikov, V. G. [Muons, Inc., 552 N. Batavia Avenue, Batavia, Illinois 60510 (United States); Turvey, M. W. [Villanova University, 800E. Lancaster Ave, Villanova, Pennsylvania 19085 (United States)

    2014-02-15

    The Spallation Neutron Source (SNS), a large scale neutron production facility, routinely operates with 30–40 mA peak current in the linac. Recent measurements have shown that our RF-driven internal antenna, Cs-enhanced, multi-cusp ion sources injects ∼55 mA of H{sup −} beam current (∼1 ms, 60 Hz) at 65-kV into a Radio Frequency Quadrupole (RFQ) accelerator through a closely coupled electrostatic Low-Energy Beam Transport system. Over the last several years a decrease in RFQ transmission and issues with internal antennas has stimulated source development at the SNS both for the internal and external antenna ion sources. This report discusses progress in improving internal antenna reliability, H{sup −} yield improvements which resulted from modifications to the outlet aperture assembly (applicable to both internal and external antenna sources) and studies made of the long standing problem of beam persistence with the external antenna source. The current status of the external antenna ion source will also be presented.

  18. Dose coefficients for inhalation of radionuclides generated through the nuclear spallation reaction by high-energy protons

    Energy Technology Data Exchange (ETDEWEB)

    Endo, Akira; Takada, Hiroshi; Yamaguchi, Yasuhiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-10-01

    Dose coefficients have been calculated for inhalation of radionuclides generated in spallation neutron targets and not listed in ICRP Publication 68. Eleven radionuclides, generated in large quantities in the targets and having half-lives more than 10 minutes, were selected for the present calculation. The calculation of the dose coefficients was performed with LUDEP, a program implementing the ICRP Publication 66 respiratory tract model, and NUDAT, a decay radiation database processed from ENSDF. Comparisons were made between the dose coefficients calculated by LUDEP and those listed in ICRP Publication 68 in order to validate the calculated dose coefficients. For 228 cases that vary inhaled particle diameters and biokinetic models of 66 radionuclides, the dose coefficients calculated by LUDEP agreed with those of ICRP Publication 68 within {+-} 25% for 213 cases. Discrepancies that exceed the ICRP`s coefficients by {+-} 25% were mainly attributable to the difference of radiation data employed. It was confirmed from the comparisons that the dose coefficients calculated by the present method are reliable ones. Annual limits on intake and derived air concentrations were calculated on the basis of the dose coefficients. It can be concluded that the dose coefficients and limits calculated here are useful from viewpoints of the design of ventilation system and the evaluation of internal exposures in high energy proton accelerator facilities. (author)

  19. Thermal hydraulic studies of spallation target for one-way coupled Indian accelerator driven systems with low energy proton beam

    Indian Academy of Sciences (India)

    V Mantha; A K Mohanty; P Satyamurthy

    2007-02-01

    BARC has recently proposed a one-way coupled ADS reactor. This reactor requires typically ∼ 1 GeV proton beam with 2 mA of current. Approximately 8 kW of heat is deposited in the window of the target. Circulating liquid metal target (lead/lead-bismuth-eutectic) has to extract this heat and this is a critical R&D problem to be solved. At present there are very few accelerators, which can give few mA and high-energy proton beam. However, accelerators with low energy and hundreds of micro-ampere current are commercially available. In view of this, it is proposed in this paper to simulate beam window heating of ∼ 8 kW in the target with low-energy proton beam. Detailed thermal analysis in the spallation and window region has been carried out to study the capability of heat extraction by circulating LBE for a typical target loop with a proton beam of 30 MeV energy and current of 0.267 mA. The heat deposition study is carried out using FLUKA code and flow analysis by CFD code. The detailed analysis of this work is presented in this paper.

  20. Effects of pulsed power input into a liquid metal target

    CERN Document Server

    Ni, L; Spitzer, H

    1999-01-01

    In order to validate the computations of stress generated in the target container by the sudden input of a large amount of power in the liquid metal of a high-power spallation target, first experimental investigations were carried out in an international collaboration. Temperature and beam profile measurements showed that up to 61% of the incoming beam power was deposited in the target. The spatial power distribution was reconstructed from the experimental data. A computational model with consideration of fluid-structure interface was employed to simulate the pressure waves in the liquid and the resulting dynamic stress on the container. The maximum stress on the container was found to be 13.6 MP. Although experimental data are still very preliminary, a comparison of the measured stress and deformation data with the computational results showed reasonable agreement in the amplitudes, which are the most important data for engineering design. Although the methods developed to measure the strain on the target su...

  1. Novel Large Area High Resolution Neutron Detector for the Spallation Neutron Source

    Energy Technology Data Exchange (ETDEWEB)

    Lacy, Jeffrey L

    2009-05-22

    Neutron scattering is a powerful technique that is critically important for materials science and structural biology applications. The knowledge gained from past developments has resulted in far-reaching advances in engineering, pharmaceutical and biotechnology industries, to name a few. New facilities for neutron generation at much higher flux, such as the SNS at Oak Ridge, TN, will greatly enhance the capabilities of neutron scattering, with benefits that extend to many fields and include, for example, development of improved drug therapies and materials that are stronger, longer-lasting, and more impact-resistant. In order to fully realize this enhanced potential, however, higher neutron rates must be met with improved detection capabilities, particularly higher count rate capability in large size detectors, while maintaining practicality. We have developed a neutron detector with the technical and economic advantages to accomplish this goal. This new detector has a large sensitive area, offers 3D spatial resolution, high sensitivity and high count rate capability, and it is economical and practical to produce. The proposed detector technology is based on B-10 thin film conversion of neutrons in long straw-like gas detectors. A stack of many such detectors, each 1 meter in length, and 4 mm in diameter, has a stopping power that exceeds that of He-3 gas, contained at practical pressures within an area detector. With simple electronic readout methods, straw detector arrays can provide spatial resolution of 4 mm FWHM or better, and since an array detector of such form consists of several thousand individual elements per square meter, count rates in a 1 m^2 detector can reach 2?10^7 cps. Moreover, each individual event can be timetagged with a time resolution of less than 0.1 ?sec, allowing accurate identification of neutron energy by time of flight. Considering basic elemental cost, this novel neutron imaging detector can be commercially produced economically

  2. Electrostatic levitation facility optimized for neutron diffraction studies of high temperature liquids at a spallation neutron source.

    Science.gov (United States)

    Mauro, N A; Vogt, A J; Derendorf, K S; Johnson, M L; Rustan, G E; Quirinale, D G; Kreyssig, A; Lokshin, K A; Neuefeind, J C; An, Ke; Wang, Xun-Li; Goldman, A I; Egami, T; Kelton, K F

    2016-01-01

    Neutron diffraction studies of metallic liquids provide valuable information about inherent topological and chemical ordering on multiple length scales as well as insight into dynamical processes at the level of a few atoms. However, there exist very few facilities in the world that allow such studies to be made of reactive metallic liquids in a containerless environment, and these are designed for use at reactor-based neutron sources. We present an electrostatic levitation facility, NESL (for Neutron ElectroStatic Levitator), which takes advantage of the enhanced capabilities and increased neutron flux available at spallation neutron sources (SNSs). NESL enables high quality elastic and inelastic neutron scattering experiments to be made of reactive metallic and other liquids in the equilibrium and supercooled temperature regime. The apparatus is comprised of a high vacuum chamber, external and internal neutron collimation optics, and a sample exchange mechanism that allows up to 30 samples to be processed between chamber openings. Two heating lasers allow excellent sample temperature homogeneity, even for samples approaching 500 mg, and an automated temperature control system allows isothermal measurements to be conducted for times approaching 2 h in the liquid state, with variations in the average sample temperature of less than 0.5%. To demonstrate the capabilities of the facility for elastic scattering studies of liquids, a high quality total structure factor for Zr64Ni36 measured slightly above the liquidus temperature is presented from experiments conducted on the nanoscale-ordered materials diffractometer (NOMAD) beam line at the SNS after only 30 min of acquisition time for a small sample (∼100 mg).

  3. Correlation between simulations and cavitation-induced erosion damage in Spallation Neutron Source target modules after operation

    Energy Technology Data Exchange (ETDEWEB)

    Riemer, Bernie [ORNL; McClintock, David A [ORNL; Kaminskas, Saulius [ORNL; Abdou, Ashraf A [ORNL

    2014-01-01

    An explicit finite element (FE) technique developed for estimating dynamic strain in the Spallation Neutron Source (SNS) mercury target module vessel is now providing insight into cavitation damage patterns observed in used targets. The technique uses an empirically developed material model for the mercury that describes liquid-like volumetric stiffness combined with a tensile pressure cut-off limit that approximates cavitation. The longest period each point in the mercury is at the tensile cut-off threshold is denoted its saturation time. Now, the pattern of saturation time can be obtained from these simulations and is being positively correlated with observed damage patterns and is interpreted as a qualitative measure of damage potential. Saturation time has been advocated by collaborators at J-Parc as a factor in predicting bubble nuclei growth and collapse intensity. The larger the ratio of maximum bubble size to nucleus, the greater the bubble collapse intensity to be expected; longer saturation times result in greater ratios. With the recent development of a user subroutine for the FE solver saturation time is now provided over the entire mercury domain. Its pattern agrees with spots of damage seen above and below the beam axis on the SNS inner vessel beam window and elsewhere. The other simulation result being compared to observed damage patterns is mercury velocity at the wall. Related R&D has provided evidence for the damage mitigation that higher wall velocity provides. In comparison to observations in SNS targets, inverse correlation of high velocity to damage is seen. In effect, it is the combination of the patterns of saturation time and low velocity that seems to match actual damage patterns.

  4. Electrostatic levitation facility optimized for neutron diffraction studies of high temperature liquids at a spallation neutron source

    Science.gov (United States)

    Mauro, N. A.; Vogt, A. J.; Derendorf, K. S.; Johnson, M. L.; Rustan, G. E.; Quirinale, D. G.; Kreyssig, A.; Lokshin, K. A.; Neuefeind, J. C.; An, Ke; Wang, Xun-Li; Goldman, A. I.; Egami, T.; Kelton, K. F.

    2016-01-01

    Neutron diffraction studies of metallic liquids provide valuable information about inherent topological and chemical ordering on multiple length scales as well as insight into dynamical processes at the level of a few atoms. However, there exist very few facilities in the world that allow such studies to be made of reactive metallic liquids in a containerless environment, and these are designed for use at reactor-based neutron sources. We present an electrostatic levitation facility, NESL (for Neutron ElectroStatic Levitator), which takes advantage of the enhanced capabilities and increased neutron flux available at spallation neutron sources (SNSs). NESL enables high quality elastic and inelastic neutron scattering experiments to be made of reactive metallic and other liquids in the equilibrium and supercooled temperature regime. The apparatus is comprised of a high vacuum chamber, external and internal neutron collimation optics, and a sample exchange mechanism that allows up to 30 samples to be processed between chamber openings. Two heating lasers allow excellent sample temperature homogeneity, even for samples approaching 500 mg, and an automated temperature control system allows isothermal measurements to be conducted for times approaching 2 h in the liquid state, with variations in the average sample temperature of less than 0.5%. To demonstrate the capabilities of the facility for elastic scattering studies of liquids, a high quality total structure factor for Zr64Ni36 measured slightly above the liquidus temperature is presented from experiments conducted on the nanoscale-ordered materials diffractometer (NOMAD) beam line at the SNS after only 30 min of acquisition time for a small sample (˜100 mg).

  5. Electrostatic levitation facility optimized for neutron diffraction studies of high temperature liquids at a spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Mauro, N. A., E-mail: namauro@noctrl.edu [Department of Physics, North Central College, Naperville, Illinois 60540 (United States); Vogt, A. J. [Instrument and Source Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Derendorf, K. S. [Mechanical Engineering and Materials Science, Washington University, St. Louis, Missouri 63130 (United States); Johnson, M. L.; Kelton, K. F. [Department of Physics and Institute of Materials Science and Engineering, Washington University, 1 Brookings Drive, St. Louis, Missouri 63130 (United States); Rustan, G. E.; Quirinale, D. G.; Goldman, A. I. [Department of Physics and Astronomy, Iowa State University, Ames, Iowa 50011 (United States); Kreyssig, A. [Department of Physics and Astronomy, Iowa State University, Ames, Iowa 50011 (United States); Division of Materials Sciences and Engineering, Ames Laboratory, Ames, Iowa 50011 (United States); Lokshin, K. A. [Department of Materials Science and Engineering, University of Tennessee, Knoxville, Tennessee 37996 (United States); Quantum Condensed Matter Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Neuefeind, J. C.; An, Ke [Chemical and Engineering Materials Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Wang, Xun-Li [Department of Physics and Materials Science, City University of Hong Kong, 83 Tat Chee Ave., Kowloon (Hong Kong); Egami, T. [Department of Materials Science and Engineering, University of Tennessee, Knoxville, Tennessee 37996 (United States); Department of Physics and Astronomy, Joint Institute for Neutron Sciences, University of Tennessee, Knoxville, Tennessee 37996 (United States)

    2016-01-15

    Neutron diffraction studies of metallic liquids provide valuable information about inherent topological and chemical ordering on multiple length scales as well as insight into dynamical processes at the level of a few atoms. However, there exist very few facilities in the world that allow such studies to be made of reactive metallic liquids in a containerless environment, and these are designed for use at reactor-based neutron sources. We present an electrostatic levitation facility, NESL (for Neutron ElectroStatic Levitator), which takes advantage of the enhanced capabilities and increased neutron flux available at spallation neutron sources (SNSs). NESL enables high quality elastic and inelastic neutron scattering experiments to be made of reactive metallic and other liquids in the equilibrium and supercooled temperature regime. The apparatus is comprised of a high vacuum chamber, external and internal neutron collimation optics, and a sample exchange mechanism that allows up to 30 samples to be processed between chamber openings. Two heating lasers allow excellent sample temperature homogeneity, even for samples approaching 500 mg, and an automated temperature control system allows isothermal measurements to be conducted for times approaching 2 h in the liquid state, with variations in the average sample temperature of less than 0.5%. To demonstrate the capabilities of the facility for elastic scattering studies of liquids, a high quality total structure factor for Zr{sub 64}Ni{sub 36} measured slightly above the liquidus temperature is presented from experiments conducted on the nanoscale-ordered materials diffractometer (NOMAD) beam line at the SNS after only 30 min of acquisition time for a small sample (∼100 mg)

  6. Influence of sweeping detonation-wave loading on damage evolution during spallation loading of tantalum in both a planar and curved geometry

    Energy Technology Data Exchange (ETDEWEB)

    Gray, George Thompson III [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hull, Lawrence Mark [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Livescu, Veronica [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Faulkner, James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Briggs, Matthew E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meyer, Ross Keith [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Andrews, Heather Lynn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hare, Steven John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Jakulewicz, Micah Shawn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Shinas, Michael A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-03-30

    Widespread research over the past five decades has provided a wealth of experimental data and insight concerning the shock hardening, damage evolution, and the spallation response of materials subjected to square-topped shock-wave loading profiles. However, fewer quantitative studies have been conducted on the effect of direct, in-contact, high explosive (HE)-driven Taylor wave (unsupported shocks) loading on the shock hardening, damage evolution, or spallation response of materials. Systematic studies quantifying the effect of sweeping-detonation wave loading are yet sparser. In this study, the damage evolution and spallation response of Ta is shown to be critically dependent on the peak shock stress, the geometry of the sample (flat or curved plate geometry), and the shock obliquity during sweeping-detonation-wave shock loading. Sweepingwave loading in the flat-plate geometry is observed to: a) yield a lower spall strength than previously documented for 1-D supported-shock-wave loading, b) exhibit increased shock hardening as a function of increasing obliquity, and c) lead to an increased incidence of deformation twin formation with increasing shock obliquity. Sweeping-wave loading of a 10 cm radius curved Ta plate is observed to: a) lead to an increase in the shear stress as a function of increasing obliquity, b) display a more developed level of damage evolution, extensive voids and coalescence, and lower spall strength with obliquity in the curved plate than seen in the flat-plate sweeping-detonation wave loading for an equivalent HE loading, and c) no increased propensity for deformation twin formation with increasing obliquity as seen in the flat-plate geometry. The overall observations comparing and contrasting the flat versus curved sweeping-wave spall experiments with 1D loaded spallation behavior suggests a coupled influence of obliquity and geometry on dynamic shock-induced damage evolution and spall strength. Coupled experimental and modeling research

  7. Coprecipitation experiment with Sm hydroxide using a multitracer produced by nuclear spallation reaction: A tool for chemical studies with superheavy elements.

    Science.gov (United States)

    Kasamatsu, Yoshitaka; Yokokita, Takuya; Toyomura, Keigo; Shigekawa, Yudai; Haba, Hiromitsu; Kanaya, Jumpei; Huang, Minghui; Ezaki, Yutaka; Yoshimura, Takashi; Morita, Kosuke; Shinohara, Atsushi

    2016-12-01

    To establish a new methodology for superheavy element chemistry, the coprecipitation behaviors of 34 elements with samarium hydroxide were investigated using multitracer produced by a spallation of Ta. The chemical reactions were rapidly equilibrated within 10s for many elements. In addition, these elements exhibited individual coprecipitation behaviors, and the behaviors were qualitatively related to their hydroxide precipitation behaviors. It was demonstrated that the ammine and hydroxide complex formations of superheavy elements could be investigated using the established method. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Rarefaction after fast laser heating of thin metal film on a glass mount: spallation and inflation from one-dimensional to three-dimensional ablation flow

    Science.gov (United States)

    Inogamov, Nail; Khokhlov, Viktor; Petrov, Yury; Zhakhovsky, Vasily; Migdal, Kirill; Ilnitsky, Denis; Hasegawa, Noboru; Nishikino, Masaharu; Yamagiwa, Mitsuru; Ishino, Masahiko; Kawachi, Tetsuya; Faenov, Anatoly; Pikuz, Tatiana; Takayoshi, Shintaro; Eyama, Takashi; Kakimoto, Naoya; Tomita, Takuro; Baba, Motoyoshi; Minami, Yasuo; Suemoto, Tohru

    2015-06-01

    We numerically and experimentally consider the effect of subpicosecond Ti:sapp laser pump pulse onto 60-100 nm silver and gold films mounted onto a silica substrate. Pump pulse spalls out the film from the substrate. Influence of diameter of a laser irradiated spot 1-100 microns on a film surface is studied. A cupola like spallation shell is flying from the substrate. For the large spot the soft X-ray probe laser is used for measuring the ablation process. The research (NAI, VVZh, VAKh, DKI, YVP, KPM, AYF, TAP) has been performed under financial support from Russian Science Foundation (RSCF) (Project No. 14-19-01599).

  9. A compact time-of-flight SANS instrument optimised for measurements of small sample volumes at the European Spallation Source

    Science.gov (United States)

    Kynde, Søren; Hewitt Klenø, Kaspar; Nagy, Gergely; Mortensen, Kell; Lefmann, Kim; Kohlbrecher, Joachim; Arleth, Lise

    2014-11-01

    The high flux at European Spallation Source (ESS) will allow for performing experiments with relatively small beam-sizes while maintaining a high intensity of the incoming beam. The pulsed nature of the source makes the facility optimal for time-of-flight small-angle neutron scattering (ToF-SANS). We find that a relatively compact SANS instrument becomes the optimal choice in order to obtain the widest possible q-range in a single setting and the best possible exploitation of the neutrons in each pulse and hence obtaining the highest possible flux at the sample position. The instrument proposed in the present article is optimised for performing fast measurements of small scattering volumes, typically down to 2×2×2 mm3, while covering a broad q-range from about 0.005 1/Å to 0.5 1/Å in a single instrument setting. This q-range corresponds to that available at a typical good BioSAXS instrument and is relevant for a wide set of biomacromolecular samples. A central advantage of covering the whole q-range in a single setting is that each sample has to be loaded only once. This makes it convenient to use the fully automated high-throughput flow-through sample changers commonly applied at modern synchrotron BioSAXS-facilities. The central drawback of choosing a very compact instrument is that the resolution in terms of δλ / λ obtained with the short wavelength neutrons becomes worse than what is usually the standard at state-of-the-art SANS instruments. Our McStas based simulations of the instrument performance for a set of characteristic biomacromolecular samples show that the resulting smearing effects still have relatively minor effects on the obtained data and can be compensated for in the data analysis. However, in cases where a better resolution is required in combination with the large simultaneous q-range characteristic of the instrument, we show that this can be obtained by inserting a set of choppers.

  10. A compact time-of-flight SANS instrument optimised for measurements of small sample volumes at the European Spallation Source

    Energy Technology Data Exchange (ETDEWEB)

    Kynde, Søren, E-mail: kynde@nbi.ku.dk [Niels Bohr Institute, University of Copenhagen (Denmark); Hewitt Klenø, Kaspar [Niels Bohr Institute, University of Copenhagen (Denmark); Nagy, Gergely [SINQ, Paul Scherrer Institute (Switzerland); Mortensen, Kell; Lefmann, Kim [Niels Bohr Institute, University of Copenhagen (Denmark); Kohlbrecher, Joachim, E-mail: Joachim.kohlbrecher@psi.ch [SINQ, Paul Scherrer Institute (Switzerland); Arleth, Lise, E-mail: arleth@nbi.ku.dk [Niels Bohr Institute, University of Copenhagen (Denmark)

    2014-11-11

    The high flux at European Spallation Source (ESS) will allow for performing experiments with relatively small beam-sizes while maintaining a high intensity of the incoming beam. The pulsed nature of the source makes the facility optimal for time-of-flight small-angle neutron scattering (ToF-SANS). We find that a relatively compact SANS instrument becomes the optimal choice in order to obtain the widest possible q-range in a single setting and the best possible exploitation of the neutrons in each pulse and hence obtaining the highest possible flux at the sample position. The instrument proposed in the present article is optimised for performing fast measurements of small scattering volumes, typically down to 2×2×2 mm{sup 3}, while covering a broad q-range from about 0.005 1/Å to 0.5 1/Å in a single instrument setting. This q-range corresponds to that available at a typical good BioSAXS instrument and is relevant for a wide set of biomacromolecular samples. A central advantage of covering the whole q-range in a single setting is that each sample has to be loaded only once. This makes it convenient to use the fully automated high-throughput flow-through sample changers commonly applied at modern synchrotron BioSAXS-facilities. The central drawback of choosing a very compact instrument is that the resolution in terms of δλ/λ obtained with the short wavelength neutrons becomes worse than what is usually the standard at state-of-the-art SANS instruments. Our McStas based simulations of the instrument performance for a set of characteristic biomacromolecular samples show that the resulting smearing effects still have relatively minor effects on the obtained data and can be compensated for in the data analysis. However, in cases where a better resolution is required in combination with the large simultaneous q-range characteristic of the instrument, we show that this can be obtained by inserting a set of choppers.

  11. Fast simulation approaches for power fluctuation model of wind farm based on frequency domain

    DEFF Research Database (Denmark)

    Lin, Jin; Gao, Wen-zhong; Sun, Yuan-zhang

    2012-01-01

    This paper discusses one model developed by Riso, DTU, which is capable of simulating the power fluctuation of large wind farms in frequency domain. In the original design, the “frequency-time” transformations are time-consuming and might limit the computation speed for a wind farm of large size....... is more than 300 times if all these approaches are adopted, in any low, medium and high wind speed test scenarios....

  12. Elastic plate spallation

    Science.gov (United States)

    Oline, L.; Medaglia, J.

    1972-01-01

    The dynamic finite element method was used to investigate elastic stress waves in a plate. Strain displacement and stress strain relations are discussed along with the stiffness and mass matrix. The results of studying point load, and distributed load over small, intermediate, and large radii are reported. The derivation of finite element matrices, and the derivation of lumped and consistent matrices for one dimensional problems with Laplace transfer solutions are included. The computer program JMMSPALL is also included.

  13. ADS无窗散裂靶件水模拟实验研究%Studies on Free Surface Flow in ADS Windowless Spallation Target

    Institute of Scientific and Technical Information of China (English)

    强成文; 赵强; 李龙; 王飞; 杨伟峰; 张学智; 张雪荧

    2015-01-01

    As the coupling component between accelerator and subcritical core, the spallation target is of crucial importance to the operation safety of the whole system. Hence, the spallation target is one of the most important parts in ADS corresponding researches. Due to lifetime limitation of material, the windowless target which has a stable free surface attracts more and more attention. The present paper deals with the experimental investigation on the free surface behavior in an approximately 1:1 size windowless target model using water as test fluid. We can get the flow and pressure conditions of windowless spallation target water simulation experiment from the platform. The free surface and field visualization were obtained by particle imaging velocimetry. The results show that the position and flow pattern of the free surface depend on experimental pressure, flow velocity and geometry of the target.%散裂靶件作为加速器和次临界堆芯的耦合部件,是ADS系统相关研究最主要的组成部分之一。无窗靶巧妙地利用了液体的自由液面特性,避免了质子束对结构材料直接轰击,是一种很有前景的散裂靶靶件形式。采用水作为实验工质搭建了一套无窗散裂靶水模拟实验台架,该实验系统覆盖了无窗散裂靶水模拟实验所需的流量及压力条件,采用粒子图像测速仪(PIV)对自由界面的流场进行可视化观察与分析,得到了自由界面的基本表征参数之间关系和可视化界面的流场信息。结果表明,无窗靶自由液面的位置和形状受到回路整体流量、压力和靶件几何尺寸的影响。

  14. 275 C Downhole Switched-Mode Power Supply

    Energy Technology Data Exchange (ETDEWEB)

    Chris Hutchens; Vijay Madhuravasal

    2008-08-31

    A vee-square (V2) control based controller IC is developed for a switch mode power supply capable of operating at extreme temperature/harsh environment conditions. A buck type regulator with silicon carbide power junction field effect transistors (JFET) as power devices is used to analyze the performance of controller. Special emphases are made on the analog sub-blocks--voltage reference, operational transconductance amplifier and comparator as individual building blocks. Transformer coupled gate drives and high temperature operable magnetic cores and capacitors are identified and tested for use in the design. Conventional ceramic chip packaging of ICs combined with lead carrier type mounting of passive filter components is introduced for hybrid packaging of the complete product. The developed SMPS is anticipated to support the operation of down-hole microcontrollers and other electronics devices that require low/medium power filtered dc inputs over an operating temperature of 275 C.

  15. Cross section measurement of residues produced in proton- and deuteron-induced spallation reactions on 93Zr at 105 MeV/u using the inverse kinematics method

    Science.gov (United States)

    Kawase, Shoichiro; Watanabe, Yukinobu; Wang, He; Otsu, Hideaki; Sakurai, Hiroyoshi; Takeuchi, Satoshi; Togano, Yasuhiro; Nakamura, Takashi; Maeda, Yukie; Ahn, Deuk Soon; Aikawa, Masayuki; Araki, Shouhei; Chen, Sidong; Chiga, Nobuyuki; Doornenbal, Pieter; Fukuda, Naoki; Ichihara, Takashi; Isobe, Tadaaki; Kawakami, Shunsuke; Kin, Tadahiro; Kondo, Yosuke; Koyama, Shunpei; Kubo, Toshiyuki; Kubono, Shigeru; Kurokawa, Meiko; Makinaga, Ayano; Matsushita, Masafumi; Matsuzaki, Teiichiro; Michimasa, Shin'ichiro; Momiyama, Satoru; Nagamine, Shunsuke; Nakano, Keita; Niikura, Megumi; Ozaki, Tomoyuki; Saito, Atsumi; Saito, Takeshi; Shiga, Yoshiaki; Shikata, Mizuki; Shimizu, Yohei; Shimoura, Susumu; Sumikama, Toshiyuki; Söderström, Pär-Anders; Suzuki, Hiroshi; Takeda, Hiroyuki; Taniuchi, Ryo; Tsubota, Jun'ichi; Watanabe, Yasushi; Wimmer, Kathrin; Yamamoto, Tatsuya; Yoshida, Koichi

    2017-09-01

    Isotopic production cross sections in the proton- and deuteron-induced spallation reactions on 93Zr at an energy of 105 MeV/u were measured in inverse kinematics conditions for the development of realistic nuclear transmutation processes for long-lived fission products (LLFPs) with neutron and light-ion beams. The experimental results were compared to the PHITS calculations describing the intra-nuclear cascade and evaporation processes. Although an overall agreement was obtained, a large overestimation of the production cross sections for the removal of a few nucleons was seen. A clear shell effect associated with the neutron magic number N = 50 was observed in the measured isotopic production yields of Zr and Y isotopes, which can be reproduced reasonably by the PHITS calculation.

  16. Transmutation of 129I and 237Np using spallation neutrons produced by 1.5, 3.7 and 7.4 GeV protons

    Science.gov (United States)

    Wan, J.-S.; Schmidt, Th.; Langrock, E.-J.; Vater, P.; Brandt, R.; Adam, J.; Bradnova, V.; Bamblevski, V. P.; Gelovani, L.; Gridnev, T. D.; Kalinnikov, V. G.; Krivopustov, M. I.; Kulakov, B. A.; Sosnin, A. N.; Perelygin, V. P.; Pronskikh, V. S.; Stegailov, V. I.; Tsoupko-Sitnikov, V. M.; Modolo, G.; Odoj, R.; Phlippen, P.-W.; Zamani-Valassiadou, M.; Adloff, J. C.; Debeauvais, M.; Hashemi-Nezhad, S. R.; Guo, S.-L.; Li, L.; Wang, Y.-L.; Dwivedi, K. K.; Zhuk, I. V.; Boulyga, S. F.; Lomonossova, E. M.; Kievitskaja, A. F.; Rakhno, I. L.; Chigrinov, S. E.; Wilson, W. B.

    2001-05-01

    Small samples of 129I and 237Np, two long-lived radwaste nuclides, were exposed to spallation neutron fluences from relatively small metal targets of lead and uranium, that were surrounded with a 6 cm thick paraffin moderator, and irradiated with 1.5, 3.7 and 7.4 GeV protons. The (n,γ) transmutation rates were determined for these nuclides. Conventional radiochemical La- and U-sensors and a variety of solid-state nuclear track detectors were irradiated simultaneously with secondary neutrons. Compared with results from calculations with well-known cascade codes (LAHET from Los Alamos and DCM/CEM from Dubna), the observed secondary neutron fluences are larger.

  17. Transmutation of {sup 129}I and {sup 237}Np using spallation neutrons produced by 1.5, 3.7 and 7.4 GeV protons

    Energy Technology Data Exchange (ETDEWEB)

    Wan, J.-S.; Schmidt, T.Th.; Langrock, E.-J.; Vater, P.; Brandt, R. E-mail: brandtr@mailer.uni-marburg.de; Adam, J.; Bradnova, V.; Bamblevski, V.P.; Gelovani, L.; Gridnev, T.D.; Kalinnikov, V.G.; Krivopustov, M.I.; Kulakov, B.A.; Sosnin, A.N.; Perelygin, V.P.; Pronskikh, V.S.; Stegailov, V.I.; Tsoupko-Sitnikov, V.M.; Modolo, G.; Odoj, R.; Phlippen, P.-W.; Zamani-Valassiadou, M.; Adloff, J.C.; Debeauvais, M.; Hashemi-Nezhad, S.R.; Guo, S.-L.; Li, L.; Wang, Y.-L.; Dwivedi, K.K.; Zhuk, I.V.; Boulyga, S.F.; Lomonossova, E.M.; Kievitskaja, A.F.; Rakhno, I.L.; Chigrinov, S.E.; Wilson, W.B

    2001-05-11

    Small samples of {sup 129}I and {sup 237}Np, two long-lived radwaste nuclides, were exposed to spallation neutron fluences from relatively small metal targets of lead and uranium, that were surrounded with a 6 cm thick paraffin moderator, and irradiated with 1.5, 3.7 and 7.4 GeV protons. The (n,{gamma}) transmutation rates were determined for these nuclides. Conventional radiochemical La- and U-sensors and a variety of solid-state nuclear track detectors were irradiated simultaneously with secondary neutrons. Compared with results from calculations with well-known cascade codes (LAHET from Los Alamos and DCM/CEM from Dubna), the observed secondary neutron fluences are larger.

  18. RESONANCE CONTROL FOR THE COUPLED CAVITY LINAC AND DRIFT TUBE LINAC STRUCTURES OF THE SPALLATION NEUTRON SOURCE LINAC USING A CLOSED-LOOP WATER COOLING SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Bernardin, J. D. (John D.); Brown, R. L. (Richard L.); Brown, S. K. (Stanley K.); Bustos, G. R. (Gerald R.); Crow, M.L. (Martin L.); Gregory, W. S.; Hood, M. E. (Michael E.); Jurney, J. D. (James D.); Medalen, I. (Ivan); Owen, A. C. (Albert C.); Weiss, Robert E.

    2001-01-01

    The Spallation Neutron Source (SNS) is a facility being designed for scientific and industrial research and development. SNS will generate and use neutrons as a diagnostic tool for medical purposes, material science, etc. The neutrons will be produced by bombarding a heavy metal target with a high-energy beam of protons, generated and accelerated with a linear particle accelerator, or linac. The low energy end of the linac consists of two room temperature copper structures, the drift tube linac (DTL), and the coupled cavity linac (CCL). Both of these accelerating structures use large amounts of electrical energy to accelerate the protons to an energy of 185 MeV. Approximately 60-80% of the electrical energy is dissipated in the copper structure and must be removed. This is done using specifically designed water cooling passages within the linac's copper structure. Cooling water is supplied to these cooling passages by specially designed resonance control and water cooling systems.

  19. Measuring the cross sections of heavy-metal spallation induced by deuterons with energies of 2, 2.94, and 3.5 GeV per nucleon

    Science.gov (United States)

    Artyushenko, M. Yu.; Baldin, A. A.; Berlev, A. I.; Bukhal, O. V.; Voronko, V. A.; Gusak, K. V.; Zhuk, I. V.; Kudashkin, I. V.; Paraipan, M.; Potapenko, A. S.; Safronova, A. A.; Sotnikov, V. V.; Tyutyunnikov, S. I.

    2016-07-01

    The cross sections for the spallation of the heavy-metal nuclei 181Ta, 197Au, 207Pb, 209Bi, 232Th, and 238U induced by relativistic deuterons with energies of 2, 2.94, and 3.5 GeV per nucleon are measured using the deuteron beam from the Nuclotron accelerator of the JINR Laboratory of High Energy Physics in Dubna, Russia. The cross-section measurements employ a combined experimental technique involving the solidstate nuclear-track detectors and the activation gamma spectrometry. Adding our measurements to the database of experimental nuclear data will make it possible to test the computer codes used for selecting the parameters of the ADS-type facilities.

  20. Uppsala High Power Test Stand for ESS Spoke Cavities

    CERN Document Server

    Yogi, RA; Dancila, D; Gajewski, K; Hermansson, L; Noor, M; Wedberg, R; Santiago-Kern, R; Ekelöf, T; Lofnes, T; Ziemann, V; Goryashko, V; Ruber, R

    2013-01-01

    The European Spallation Source (ESS) is one of the world’s most powerful neutron source. The ESS linac will accelerate 50mA pulse current of protons to 2.5GeV in 2.86 ms long pulses at a repetition rate of 14 Hz. It produces a beam with 5MW average power and 125MW peak power. ESS Spoke Linac consist of 28 superconducting spoke cavities, which will be developed by IPN Orsay, France. These Spoke Cavities will be tested at low power at IPN Orsay and high power testing will be performed in a high power test stand at Uppsala University. The test stand consists of tetrode based RF amplifier chain (352MHz, 350 kW) power and related RF distribution. Outputs of two tetrodes shall be combined with the hybrid coupler to produce 350 kW power. Preamplifier for a tetrode shall be solid state amplifier. As the spoke cavities are superconducting, the test stand also includes horizontal cryostat, Helium liquefier, test bunker etc. The paper describes features of the test stand in details.

  1. Experimental verification of equilibrium para-hydrogen levels in hydrogen moderators irradiated by spallation neutrons at J-PARC

    Science.gov (United States)

    Teshigawara, M.; Harada, M.; Tatsumoto, H.; Aso, T.; Ohtsu, K.; Takada, H.; Futakawa, M.; Ikeda, Y.

    2016-02-01

    By sampling gaseous hydrogen from a circulating liquid hydrogen loop for Laser Raman spectroscopy, we measured the para-/ortho-hydrogen fractions in liquid hydrogen under neutron irradiation for the first time to identify whether irradiated hydrogen has an elevated ortho-hydrogen fraction. This measurement indicates that para-hydrogen equilibrium persists at 300 kW proton power in the presence of an iron(III) oxide hydroxide [Fe(OH)3] catalyst. The measurements will be repeated as the power at the Japan Proton Accelerator Research Complex (J-PARC) increases to the MW level.

  2. Safety analysis and lay-out aspects of shieldings against particle radiation at the example of spallation facilities in the megawatt range; Sicherheitstechnische Analyse und Auslegungsaspekte von Abschirmungen gegen Teilchenstrahlung am Beispiel von Spallationsanlagen im Megawatt Bereich

    Energy Technology Data Exchange (ETDEWEB)

    Hanslik, R.

    2006-08-15

    This paper discusses the shielding of particle radiation from high current accelerators, spallation neutron sources and so called ADS-facilities (Accelerator Driven Systems). ADS-facilities are expected to gain importance in the future for transmutation of long-lived isotopes from fission reactors as well as for energy production. In this paper physical properties of the radiation as well as safety relevant requirements and corresponding shielding concepts are discussed. New concepts for the layout and design of such shielding are presented. Focal point of this work will be the fundamental difference between conventional fission reactor shielding and the safety relevant issues of shielding from high-energy radiation. Key point of this paper is the safety assessment of shielding issues of high current accelerators, spallation targets and ADS-blanket systems as well as neutron scattering instruments at spallation neutron sources. Safety relevant shielding requirements are presented and discussed. For the layout and design of the shielding for spallation sources computer base calculations methods are used. A discussion and comparison of the most important methods like semi-empirical, deterministic and stochastic codes are presented. Another key point within the presented paper is the discussion of shielding materials and their shielding efficiency concerning different types of radiation. The use of recycling material, as a cost efficient solution, is discussed. Based on the conducted analysis, flowcharts for a systematic layout and design of adequate shielding for targets and accelerators have been developed and are discussed in this paper. By use of these flowcharts layout and engineering design of future ADS-facilities can be performed. (orig.)

  3. Safety analysis and lay-out aspects of shieldings against particle radiation at the example of spallation facilities in the megawatt range; Sicherheitstechnische Analyse und Auslegungsaspekte von Abschirmungen gegen Teilchenstrahlung am Beispiel von Spallationsanlagen im Megawatt Bereich

    Energy Technology Data Exchange (ETDEWEB)

    Hanslik, R.

    2006-08-15

    This paper discusses the shielding of particle radiation from high current accelerators, spallation neutron sources and so called ADS-facilities (Accelerator Driven Systems). ADS-facilities are expected to gain importance in the future for transmutation of long-lived isotopes from fission reactors as well as for energy production. In this paper physical properties of the radiation as well as safety relevant requirements and corresponding shielding concepts are discussed. New concepts for the layout and design of such shielding are presented. Focal point of this work will be the fundamental difference between conventional fission reactor shielding and the safety relevant issues of shielding from high-energy radiation. Key point of this paper is the safety assessment of shielding issues of high current accelerators, spallation targets and ADS-blanket systems as well as neutron scattering instruments at spallation neutron sources. Safety relevant shielding requirements are presented and discussed. For the layout and design of the shielding for spallation sources computer base calculations methods are used. A discussion and comparison of the most important methods like semi-empirical, deterministic and stochastic codes are presented. Another key point within the presented paper is the discussion of shielding materials and their shielding efficiency concerning different types of radiation. The use of recycling material, as a cost efficient solution, is discussed. Based on the conducted analysis, flowcharts for a systematic layout and design of adequate shielding for targets and accelerators have been developed and are discussed in this paper. By use of these flowcharts layout and engineering design of future ADS-facilities can be performed. (orig.)

  4. Modeling research in low-medium temperature geothermal field, Tianjin

    Institute of Scientific and Technical Information of China (English)

    王坤; 李春华

    2002-01-01

    The geothermal reservoir in Tianjin can be divided into two parts: the upper one is the porous medium reservoir in the Tertiary system; the lower one includes the basement reservoir in Lower Paleozoic and Middle-Upper Proterozoic. Hot springs are exposed in the northern mountain and confined geothermal water is imbedded in the southern plain. The geothermal reservoir is incised by several fractures. In recent years, TDS of the geothermal water have gone up along with the production rate increasing, along the eastern fracture zone (Cangdong Fracture and West Baitangkou Fracture). This means that the northern fracture system is the main seepage channel of the deep circulation geothermal water, and the reservoir has good connection in a certain area and definite direction. The isotopic research about hydrogen and carbon chronology indicates that the main recharge period of geothermal water is the Holocene Epoch, the pluvial and chilly period of 20 kaBP. The karst conduits in weathered carbonate rocks of the Proterozoic and Lower Paleozoic and the northeast regional fracture system are the main feeding channels of Tianjin geothermal water. Since the Holocene epoch, the geothermal water stayed at a sealed warm period. The tracer test in WR45 doublet system shows that the tracer test is a very effective measure for understanding the reservoir's transport nature and predicting the cooling time and transport velocity during the reinjection. 3-D numerical simulation shows that if the reinjection well keeps a suitable distance from the production well, reinjection will be a highly effective measure to extract more thermal energy from the rock matrix. The cooling of the production well will not be a problem.

  5. A compact 10 kW solid-state RF power amplifier at 352 MHz

    Science.gov (United States)

    Dancila, Dragos; Hoang Duc, Long; Jobs, Magnus; Holmberg, Måns; Hjort, Adam; Rydberg, Anders; Ruber, Roger

    2017-07-01

    A compact 10 kW RF power amplifier at 352 MHz was developed at FREIA for the European Spallation Source, ESS. The specifications of ESS for the conception of amplifiers are related to its pulsed operation: 3.5 ms pulse length and a duty cycle of 5%. The realized amplifier is composed of eight kilowatt level modules, combined using a planar Gysel 8-way combiner. The combiner has a low insertion loss of only 0.2 dB, measured at 10 kW peak power. Each module is built around a commercially available LDMOS transistor in a singleended architecture. During the final tests, a total output peak power of 10.5 kW was measured.

  6. Power Outages

    Science.gov (United States)

    ... Thunderstorms & Lightning Tornadoes Tsunamis Volcanoes Wildfires Main Content Power Outages This page provides basic safety tips and ... during and after a power outage. Before a Power Outage Build or restock your emergency preparedness kit , ...

  7. Wind Power

    OpenAIRE

    Makhalas, Kharsan Al; Alsehlli, Faisal

    2015-01-01

    This Bachelor thesis has been written at the Blekinge Institute of Technology. This thesis concentrates on the wind power and their components, also the large wind farm is studied. The electrical power is generated by using the power in wind to drive a wind turbine to produce mechanical power. This mechanical power can be converted into electrical power by using electrical induction generators. There are two types of the wind turbines, the horizontal axis and vertical axis wind turbine, where...

  8. Pragmatic power

    CERN Document Server

    Eccles, William

    2008-01-01

    Pragmatic Power is focused on just three aspects of the AC electrical power system that supplies and moves the vast majority of electrical energy nearly everywhere in the world: three-phase power systems, transformers, and induction motors. The reader needs to have had an introduction to electrical circuits and AC power, although the text begins with a review of the basics of AC power. Balanced three-phase systems are studied by developing their single-phase equivalents. The study includes a look at how the cost of ""power"" is affected by reactive power and power factor. Transformers are cons

  9. HEIMDAL: A thermal neutron powder diffractometer with high and flexible resolution combined with SANS and neutron imaging - Designed for materials science studies at the European Spallation Source

    Science.gov (United States)

    Holm, Sonja L.; Lefmann, Kim; Henry, Paul F.; Bertelsen, Mads; Schefer, Jürg; Christensen, Mogens

    2016-08-01

    HEIMDAL will be a multi length scale neutron scattering instrument for the study of structures covering almost nine orders of magnitude from 0.01 nm to 50 mm. The instrument is accepted for construction at the European Spallation Source (ESS) and features a variable resolution thermal neutron powder diffractometer (TNPD), combined with small angle neutron scattering (SANS) and neutron imaging (NI). The instrument uses a novel combination of a cold and a thermal guide to fulfill the diverse requirements for diffraction and SANS. With an instrument length of 170 m, HEIMDAL will take advantage of the high neutron flux of the long pulse at ESS, whilst maintaining a high q-resolution due to the long flight path. The q-range coverage is up to 20 Å-1 allowing low-resolution PDF analysis. With the addition of SANS, HEIMDAL will be able to cover a uniquely broad length scale within a single instrumental set-up. HEIMDAL will be able to accommodate modern materials research in a broad variety of fields, and the task of the instrument will be to study advanced functional materials in action, as in situ and in operandi at multiple length scales (0.01-100 nm) quasi simultaneously. The instrument combines state-of-the-art neutron scattering techniques (TNPD, SANS, and NI) with the goal of studying real materials, in real time, under real conditions. This article describes the instrument design ideas, calculations and results of simulations and virtual experiments.

  10. Capture and Fission rate of 232-Th, 238-U, 237-Np and 239-Pu from spallation neutrons in a huge block of lead.

    CERN Document Server

    Vlachoudis, Vasilis

    2000-01-01

    The study is centered on the research of the incineration possibility of nuclear waste, by the association of a particle accelerator with a multiplying medium of neutrons, in the project "Energy Amplifier" of C. Rubbia. It consists of the experimental determination of the rates of capture and fission of certain elements (232-Th, 238-U, 237-Np and 239-Pu) subjected to a fluence of fast spallation neutrons. These neutrons are produced by the interaction of high kinetic energy protons (several GeV) provided by the CERN-PS accelerator, on a large lead solid volume. The measurement techniques used in this work, are based on the activation of elements in the lead volume and the subsequent gamma spectroscopy of the activated elements, and also by the detection of fission fragment traces. The development, of a Monte Carlo code makes it possible, on one hand, to better understand the relevant processes, and on the other hand, to validate the code, by comparison with measurements, for the design and the construction of...

  11. Study of spallation target of ADS neutron source based on MCNPX%基于MCNPX对ADS中子源散裂靶的物理研究

    Institute of Scientific and Technical Information of China (English)

    时磊; 景桂芬

    2011-01-01

    The spallation target of Accelerator-Driven sub-critical System (ADS) is studied using the program MCNPX. The calculation of standard lead target bombarded with 0. 6 - 1. 5 GeV proton beams is carried out. The neutron spectra and distribution over the lead target,energy deposition and neutron production in the lead target are studied. The simulation results agree with the former theoretical and experimental results.%运用蒙卡程序MCNPX对加速器驱动次临界反应堆系统(简称ADS)的标准散裂中子靶进行了计算研究.计算了在0.6~1.5 GeV的质子轰击下,标准Pb靶发生散裂反应产生的中子产额及分布、中子能谱以及靶内能量沉积分布.计算结果与文献理论数据、实验数据进行了比较.

  12. Monte Carlo calculations on transmutation of trans-uranic nuclear waste isotopes using spallation neutrons difference of lead and graphite moderators

    CERN Document Server

    Hashemi-Nezhad, S R; Brandt, R; Krivopustov, M I; Kulakov, B A; Odoj, R; Sosnin, A N; Wan, J S; Westmeier, W

    2002-01-01

    Transmutation rates of sup 2 sup 3 sup 9 Pu and some minor actinides ( sup 2 sup 3 sup 7 Np, sup 2 sup 4 sup 1 Am, sup 2 sup 4 sup 5 Cm and sup 2 sup 4 sup 6 Cm), in two accelerator-driven systems (ADS) with lead or graphite moderating environments, were calculated using the LAHET code system. The ADS that were used had a large volume (approx 32 m sup 3) and contained no fissile material, except for a small amount of fissionable waste nuclei that existed in some cases. Calculations were performed at an incident proton energy of 1.5 GeV and the spallation target was lead. Also breeding rates of sup 2 sup 3 sup 9 Pu and sup 2 sup 3 sup 3 U as well as the transmutation rates of two long-lived fission products sup 9 sup 9 Tc and sup 1 sup 2 sup 9 I were calculated at different locations in the moderator. It is shown that an ADS with graphite moderator is a much more effective transmuter than that with lead moderator.

  13. State of the Art Power Couplers for Superconducting RF Cavities

    Energy Technology Data Exchange (ETDEWEB)

    Isidoro Campisi

    2002-08-01

    Simulations are now routinely performed that allow the prediction of electromagnetic, multipacting, thermal, and mechanical properties of couplers. From these studies, better designs have been conceived which can minimize potential problems ahead of construction. Judicious use of materials and the implementation of clean practices and of careful conditioning have gradually increased the power levels at which couplers can safely operate. Machine operation at hundreds of kilowatts has been achieved in CW at KEK and Cornell, and in a pulsed mode at the TESLA Test Facility (TTF). Test stand operations in CW at the megawatt level (Accelerator for the Production of Tritium) and in pulse mode at a peak power of 2 MW (Spallation Neutron Source, TTF version II) have been achieved. The recent progress indicates that the understanding of the behavior of fundamental power couplers is rapidly increasing and that optimal designs are being developed which will allow in the future to attain routine attainment of the megawatt power levels necessary for high-beam-power machines under construction and under study.

  14. Wind power in power systems

    CERN Document Server

    Ackermann, Thomas

    2012-01-01

    The second edition of the highly acclaimed Wind Power in Power Systems has been thoroughly revised and expanded to reflect the latest challenges associated with increasing wind power penetration levels. Since its first release, practical experiences with high wind power penetration levels have significantly increased. This book presents an overview of the lessons learned in integrating wind power into power systems and provides an outlook of the relevant issues and solutions to allow even higher wind power penetration levels. This includes the development of standard wind turbine sim

  15. Power Electronics

    DEFF Research Database (Denmark)

    Iov, Florin; Ciobotaru, Mihai; Blaabjerg, Frede

    2008-01-01

    energy at the end-user should also be set up. Deregulation of energy has in the past lowered the investment in larger power plants, which means the need for new electrical power sources will be high in the near future. Two major technologies will play important roles to solve the future problems. One...... is to change the electrical power production sources from the conventional, fossil (and short term) based energy sources to renewable energy resources. The other is to use high efficient power electronics in power generation, power transmission/distribution and end-user application. This paper discuss the most...... emerging renewable energy sources, wind energy, which by means of power electronics are changing from being a minor energy source to be acting as an important power source in the energy system. Power electronics is the enabling technology and the presentation will cover the development in wind turbine...

  16. {sup 48}Ti(n,xnpa{gamma}) reaction cross sections using spallation neutrons for E{sub n} = 1 to 20 MeV

    Energy Technology Data Exchange (ETDEWEB)

    Dashdorj, D; Mitchell, G E; Garrett, P E; Agvaanluvsan, U; Becker, J A; Bernstein, L A; Cooper, J R; Hoffman, R D; Younes, W; Devlin, N; Fotiades, N; Nelson, R O

    2005-01-06

    {gamma}-ray excitation functions have been measured for the interaction of fast neutrons with {sup 48}Ti (neutron energy from 1 MeV to 250 MeV). The Los Alamos National Laboratory spallation neutron source, at the LANSCE/WNR facility, provided a ''white'' neutron beam which is produced by bombarding a natural W target with a pulsed proton beam. The prompt-reaction {gamma} rays were measured with the large-scale Compton-suppressed Ge spectrometer, GEANIE. Neutron energies were determined by the time-of-flight technique. Excitation functions were converted to partial {gamma}-ray cross sections, taking into account the dead-time correction, the target thickness, the detector efficiency, and neutron flux (monitored with an in-line fission chamber). The data analysis is presented here for neutron energies between 1 to 20 MeV. Partial {gamma}-ray cross sections for transitions in {sup 47,48}Ti, {sup 48}Sc, and {sup 45}Ca have been determined. These results are compared to Hauser-Feshbach predictions calculated using the STAPRE code, which includes compound nuclear and pre-equilibrium emission. The partial cross sections for {gamma} rays, whose discrete {gamma}-ray cascade path leads to the ground state in {sup 48}Ti, {sup 47}Ti, {sup 48}Sc, and {sup 45}Ca have been summed to obtain estimates of the lower limits for reaction cross sections. Partial cross sections for unobserved {gamma}-rays are predicted from the STAPRE code. These lower limits are combined with Hauser-Feshbach calculations to deduce {sup 48}Ti(n,n'){sup 48}Ti, {sup 48}Ti(n,2n){sup 47}Ti, {sup 48}Ti(n,p){sup 48}Sc, and {sup 48}Ti(n,{alpha}){sup 45}Ca reaction channel cross sections.

  17. Analysis of structure and deformation behavior of AISI 316L tensile specimens from the second operational target module at the Spallation Neutron Source

    Science.gov (United States)

    Gussev, M. N.; McClintock, D. A.; Garner, F. A.

    2016-01-01

    In an earlier publication, tensile testing was performed on specimens removed from the first two operational targets of the Spallation Neutron Source (SNS). There were several anomalous features in the results. First, some specimens had very large elongations (up to 57%) while others had significantly smaller values (10-30%). Second, there was a larger than the usual amount of data scatter in the elongation results. Third, the stress-strain diagrams of nominally similar specimens spanned a wide range of behavior ranging from expected irradiation-induced hardening to varying levels of force drop after yield point and indirect signs of "traveling deformation wave" behavior associated with strain-induced martensite formation. To investigate the cause(s) of such variable tensile behavior, several specimens from Target 2, spanning the range of observed tensile behavior, were chosen for detailed microstructural examination using electron backscatter diffraction (EBSD) analysis. It was shown that the steel employed in the construction of the target contained an unexpected bimodal grain size distribution, containing very large out-of-specification grains surrounded by "necklaces" of grains of within-specification sizes. The large grains were frequently comparable to the width of the gauge section of the tensile specimen. The propensity to form martensite during deformation was shown to be accelerated by radiation but also to be very sensitive to the relative orientation of the grains with respect to the tensile axis. Specimens having large grains in the gauge that were most favorably oriented for production of martensite strongly exhibited the traveling deformation wave phenomenon, while those specimens with less favorably oriented grains had lesser or no degree of the wave effect, thereby accounting for the observed data scatter.

  18. Radiochemical determination of {sup 129}I and {sup 36}Cl in MEGAPIE, a proton irradiated lead-bismuth eutectic spallation target

    Energy Technology Data Exchange (ETDEWEB)

    Hammer-Rotzler, Bernadette; Tuerler, Andreas [Paul Scherrer Institut (PSI), Villigen (Switzerland); Bern Univ. (Switzerland); Neuhausen, Joerg; Boutellier, Viktor; Wohlmuther, Michael; Schumann, Dorothea [Paul Scherrer Institut (PSI), Villigen (Switzerland); Vockenhuber, Christof [ETH Zurich (Switzerland). Lab. of Ion Beam Physics

    2015-07-01

    The concentrations of the long-lived nuclear reaction products {sup 129}I and {sup 36}Cl have been measured in samples from the MEGAPIE liquid metal spallation target. Samples from the bulk target material (lead-bismuth eutectic, LBE), from the interface of the metal free surface with the cover gas, from LBE/steel interfaces and from noble metal absorber foils installed in the cover gas system were analysed using Accelerator Mass Spectrometry at the Laboratory of Ion beam Physics at ETH Zuerich. The major part of {sup 129}I and {sup 36}Cl was found accumulated on the interfaces, particularly at the interface of LBE and the steel walls of the target container, while bulk LBE samples contain only a minor fraction of these nuclides. Both nuclides were also detected on the absorber foils to a certain extent (<< 1% of the total amount). The latter number is negligible concerning the radio-hazard of the irradiated target material; however it indicates a certain affinity of the absorber foils for halogens, thus proving the principle of using noble metal foils for catching these volatile radionuclides. The total amounts of {sup 129}I and {sup 36}Cl in the target were estimated from the analytical data by averaging within the different groups of samples and summing up these averages over the total target. This estimation could account for about half of the amount of {sup 129}I and {sup 36}Cl predicted to be produced using nuclear physics modelling codes for both nuclides. The significance of the results and the associated uncertainties are discussed.

  19. High-power proton linac for transmuting the long-lived fission products in nuclear waste

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence, G.P.

    1991-01-01

    High power proton linacs are being considered at Los Alamos as drivers for high-flux spallation neutron sources that can be used to transmute the troublesome long-lived fission products in defense nuclear waste. The transmutation scheme being studied provides a high flux (> 10{sup 16}/cm{sup 2}{minus}s) of thermal neutrons, which efficiently converts fission products to stable or short-lived isotopes. A medium-energy proton linac with an average beam power of about 110 MW can burn the accumulated Tc99 and I129 inventory at the DOE's Hanford Site within 30 years. Preliminary concepts for this machine are described. 3 refs., 5 figs., 2 tabs.

  20. Electric Power

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ China Council for the Promotion of International Trade Electric Power Industry Office (CCPIT Electric Power), one of the pro-fessional industrial branches of China Council for the Promotion of International Trade (CCPIT), was established in 2006.

  1. Power Electronics

    DEFF Research Database (Denmark)

    Iov, Florin; Ciobotaru, Mihai; Blaabjerg, Frede

    2008-01-01

    is to change the electrical power production sources from the conventional, fossil (and short term) based energy sources to renewable energy resources. The other is to use high efficient power electronics in power generation, power transmission/distribution and end-user application. This paper discuss the most...... emerging renewable energy sources, wind energy, which by means of power electronics are changing from being a minor energy source to be acting as an important power source in the energy system. Power electronics is the enabling technology and the presentation will cover the development in wind turbine...... technology from kW to MW, discuss which power electronic solutions are most feasible and used today....

  2. Normative Power

    DEFF Research Database (Denmark)

    The social sciences have many different understandings of ‘normative power', but in European Union (EU) studies normative power has three particular meanings. The first meaning of normative power is its emphasis on normative theory, that is, how we judge and justify truth claims in social science....... The second meaning of normative power is as a form of power that is ideational rather than material or physical. The third meaning of normative power is as a characterisation of an ideal type of international actor. Empirical studies of normative forms of power have analysed both the causal and constitutive...... effects of EU relations with the world in areas ranging from inter-regional relations, through traditional diplomacy, to environmental politics. Research areas of particular interest include the study of the interplay between physical, material and normative forms of power, as well as the constitutive...

  3. Power Talk

    DEFF Research Database (Denmark)

    Angjelichinoski, Marko; Stefanovic, Cedomir; Popovski, Petar

    2016-01-01

    A standard way to realize communication in microgrid control is to use an external communication network, such as modems for wireless or power-line communication, whose implementation may be inefficient in terms of deployment cost, complexity, and system stability. In this chapter we present...... a communication solution, denoted as power talk, which is solely based on the use of the existing microgrid power equipment (i.e., power electronics and buses). The pivotal idea is to modulate information in the power-related parameters of the microgrid buses by use of the flexibility of power electronic...... interfaces. The focus of the chapter is on the design of power talk solutions for DC microgrids with droop control. Specifically, the chapter presents the power talk implementation through modification of the droop parameters of the primary control loop, and investigates the design of modulation schemes...

  4. Application of the laser spallation technique to the measurement of the adhesion strength of tungsten carbide coatings on superalloy substrates

    Energy Technology Data Exchange (ETDEWEB)

    Boustie, M.; Aoroux, E.; Romain, J.-P. [Ecole Nationale Superieure de Mecanique et d' Aerotechnique (ENSMA), 86 - Futuroscope (FR). Lab. de Combustion et de Detonique (LCD)

    2000-10-01

    High power pulsed lasers are used to induce shock waves in Hastelloy X targets coated with tungsten carbide of 70 {mu}m and 50 {mu}m thickness. In suitable irradiation conditions, a debonding of the substrate/coating interface due to the generation of tensile stresses is observed. Experimental results are analyzed with the use of numerical simulations yielding the stress history at interface and its dependence on laser pulse intensity up to 600 GW/cm{sup 2} with 1 ns and 3 ns durations under direct irradiation, and 23 ns with water confinement. As a consequence of shock decay during the propagation through the substrate, a strong variation of incident intensity results in a small variation of tensile stress. This allows an accurate determination of the debonding threshold which is found in the range of 1.0 to 1.3 GPa for short laser pulses (1 and 3 ns) and 0.5 to 0.6 GPa for long laser pulses (23 ns confined). (orig.)

  5. Application of the laser spallation technique to the measurement of the adhesion strength of tungsten carbide coatings on superalloy substrates

    Science.gov (United States)

    Boustie, M.; Auroux, E.; Romain, J.-P.

    2000-10-01

    High power pulsed lasers are used to induce shock waves in Hastelloy X targets coated with tungsten carbide of 70 μm and 50 μm thickness. In suitable irradiation conditions, a debonding of the substrate/coating interface due to the generation of tensile stresses is observed. Experimental results are analyzed with the use of numerical simulations yielding the stress history at interface and its dependence on laser pulse intensity up to 600 GW/cm2 with 1 ns and 3 ns durations under direct irradiation, and 23 ns with water confinement. As a consequence of shock decay during the propagation through the substrate, a strong variation of incident intensity results in a small variation of tensile stress. This allows an accurate determination of the debonding threshold which is found in the range of 1.0 to 1.3 GPa for short laser pulses (1 and 3 ns) and 0.5 to 0.6 GPa for long laser pulses (23 ns confined).

  6. Flower power; Flower-Power

    Energy Technology Data Exchange (ETDEWEB)

    Wiedemann, Karsten

    2010-08-15

    Scientists of Kassel university developed a concept for producing heat and electric power from grassland biomass. This strategy of decentral heat and power supply will also contribute to conservation goals. (orig.)

  7. Study of the production of residual evaporation nuclei issued from the spallation reaction of uranium-238 by 1 GeV protons; Etude de la production de noyaux residuels d'evaporation issus de la reaction de spallation de l'uranium-238 par des protons a 1 GeV

    Energy Technology Data Exchange (ETDEWEB)

    Taieb, J

    2000-10-01

    The spallation reaction by high energy protons is one of the envisaged nuclear reactions for production of exotic nuclei. We have measured the production of more than 300 different evaporation residues issued by the spallation reaction of Uranium-238 by 1 GeV protons. We used the reverse kinematics technique in order to produce the relativistic nuclei and therefore to be able to detect those nuclides within a very short time, shorter in most cases than the radioactive disintegration period. The achieved nuclear charge and mass resolution are excellent. They allow a good accuracy on the values of the measured cross-sections (10 to 15%). We have observed for the first time the nuclide Actinium-235 obtained consequently to the loss of 3 protons by the projectile. The measured isotopic distribution are strongly influenced by the mechanism of fission which leads to a strong reduction of the production of the heavy neutron deficient isotopes. We have compared our results to some other measurements achieved with radio-chemical methods at a similar energy. We observed a systematic disagreement of about 40%. Some comparison with the available systematics show that those are presently not able to reproduce the data with a reasonable precision. We could also measure the recoil momentum distribution for each studied isotopes. We show that Goldhaber's model agrees very well with the experiment in case. of 'cold' channels where the evaporation of particles never occurs. On the other hand, when the produced pre-fragment is excited the data show that Goldhaber's model does not reproduce.the data showing the limitation of such an approach. We finally tried to reproduce the measurement of evaporation residue cross-section thanks to the coupling of intra-nuclear cascade and statistical evaporation codes. The influence of the fission process is rather important is the system p+U; we therefore had to account for the dynamical aspect of the fission. We also showed

  8. Stockholm Power Tech. Power systems

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The proceedings from this symposium is presented in six volumes: Invited speakers` sessions; Power systems; Power electronics; High-voltage technology; Electrical machines and drives; and Information and control systems. This report covers the power systems volume. Separate abstracts have been prepared for 141 of the 145 papers in this volume

  9. Período anterior à interferência na cultura da soja-RR em condições de baixa, média e alta infestação Period before interference in soybean-RR crop under low, medium and high infestation level conditions

    Directory of Open Access Journals (Sweden)

    A.F. Silva

    2009-03-01

    Full Text Available Este trabalho foi conduzido com o objetivo de determinar o período anterior à interferência (PAI das plantas daninhas na cultura da soja, cv. BRS 243-RR, cultivada em condições de baixa, média e alta infestação. O delineamento experimental foi em blocos ao acaso, com dez tratamentos, constituídos por períodos crescentes de convivência das plantas daninhas com a cultura (0, 0-5, 0-10, 0-15, 0-21, 0-28, 0-35, 0 42, 0-49 e 0-125 dias. Na área de baixa infestação, as principais espécies infestantes foram Brachiaria plantaginea, Ipomoea nil e Euphorbia heterophylla. Nas áreas de média e alta infestação, destacaram-se Brachiaria plantaginea, Ipomoea nil, Digitaria horizontalis e Cyperus rotundus. Considerando 5 e 10% de tolerância na redução da produtividade da soja, conclui-se que em áreas de baixa, média e alta infestação de plantas daninhas os períodos anteriores à interferência (PAI foram de: 17 e 24 dias após a emergência (DAE, 11 e 15 DAE e 11 e 16 DAE, respectivamente. A interferência das plantas daninhas na cultura durante todo o ciclo reduziu o rendimento de grãos da soja, em média, em 73% (área de baixa infestação, 82% (área de média infestação e 92,5% (área de alta infestação.The aim of this study was to evaluate the period before weed interference in soybean culture, cv. BRS 243-RR, under low, medium and high weed density. The experimental design was arranged in complete randomized blocks, and the treatments consisted of increasing periods of weed control (0, 0-5, 0-10, 0-15, 0-21, 0-28, 0-35, 0-42, 0-49 and 0-125 days. In low weed infestation area the main weed species were: Brachiaria plantaginea,Ipomoea nil,Euphorbia heterophylla. In medium and high infestation areas, Brachiaria plantaginea,Ipomoea nil,Digitaria horizontalis and Cyperus rotundus were the most frequent weeds. Considering 5% and 10% of tolerance of soybean grain yield reduction, it was concluded that the period before

  10. HIGH POWER FAST KICKER SYSTEM FOR SNS BEAM EXTRACTION.

    Energy Technology Data Exchange (ETDEWEB)

    ZHANG,W.; SANDBERG,J.; TSOUPAS,N.; MI,J.; LAMBIASE,R.; LOCKEY,R.; PAI,C.; TUOZZOLO,J.; NEHRING,T.; WARBURTON,D.

    2002-06-30

    A Blumlein topology based high peak power, high repetition rate, and low beam impedance fast extraction kicker system for ORNL Spallation Neutron Source (SNS) is being developed at Brookhaven National Laboratory. The large magnet window size, large deflecting angle, low beam impedance termination and fast deflecting field rise time demand a very strong pulsed power source to drive the SNS extraction fast kicker magnet. This system consists of fourteen high voltage modulators and fourteen lumped kicker magnet sections. All modulators will be located in a service building outside the beam tunnel, which is a revised design requirement adopted in the mid 2000. The high current pulses generated by the high power modulators will be delivered through high voltage pulsed transmission cables to each kicker magnet sections. The designed output capacity of this system, is in multiple GVA. Its first article modulator has been constructed and is being tested. In this paper, we present the system overview, project status and the advantages of this new conceptual design.

  11. Distributed Generation in Power Systems: An Overview and Key Issues

    DEFF Research Database (Denmark)

    Singh, Sri Niwas

    2009-01-01

    The necessity for smart electrical systems having minimum technical loss and environmental impact is providing impetus to go for Distributed Generations (DGs) which may offer several other advantages such as reduced transmission and distribution system resources, increased reliability, better power...... quality, etc. However, depending on the system configuration and management, these advantages may not be true. Moreover, due to structural and managerial changes in the electricity supply industry motivated with introduction of completion, the role of small generations distributed in the low....../medium voltage network has gained importance. This paper adopts a systematic approach by focusing on the most important research areas related to the distributed generations. Various DG technologies are described and penetration of DGs in the Indian system has been discussed. This paper also highlights the key...

  12. Pathways for the release of polonium from a lead-bismuth spallation target (thermochemical calculation); Verfluechtigungspfade des Poloniums aus einem Pb-Bi-Spallationstarget (Thermochemische Kalkulation)

    Energy Technology Data Exchange (ETDEWEB)

    Eichler, B.; Neuhausen, J

    2004-06-01

    An analysis of literature data for the thermochemical constants of polonium reveals considerable discrepancies in the relations of these data among each other as well as in their expected trends within the chalcogen group. This fact hinders a reliable assessment of possible reaction paths for the release of polonium from a liquid lead-bismuth spallation target. In this work an attempt is made to construct a coherent data set for the thermochemical properties of polonium and some of its compounds that are of particular importance with respect to the behaviour of polonium in a liquid Pb-Bi target. This data set is based on extrapolations using general trends throughout the periodic table and, in particular, within the chalcogen group. Consequently, no high accuracy should be attributed to the derived data set. However, the data set derived in this work is consistent with definitely known experimental data. Furthermore, it complies with the general trends of physicochemical properties within the chalcogen group. Finally, well known relations between thermochemical quantities are fulfilled by the data derived in this work. Thus, given the lack of accurate experimental data it can be regarded as best available data. Thermochemical constants of polonium hydride, lead polonide and polonium dioxide are derived based on extrapolative procedures. Furthermore, the possibility of formation of the gaseous intermetallic molecule BiPo, which has been omitted from discussion up to now, is investigated. From the derived thermochemical data the equilibrium constants of formation, release and dissociation reactions are calculated for different polonium containing species. Furthermore equilibrium constants are determined for the reaction of lead polonide and polonium dioxide with hydrogen, water vapour and the target components lead and bismuth. The most probable release pathways are discussed. From thermochemical evaluations polonium is expected to be released from liquid lead

  13. DTL Construction Status of China Spallation Neutron Source%中国散裂中子源漂移管直线加速器研制进展

    Institute of Scientific and Technical Information of China (English)

    刘华昌; 瞿培华; 宋洪; 关玉慧; 赵晶晶; 董岚; 王生; 傅世年; 彭军; 巩克云; 吴小磊; 李阿红; 李波; 陈强; 樊梦旭; 王云

    2015-01-01

    The 324 MHz alvarez‐type drift tube linac (DTL) for China Spallation Neu‐tron Source is used to accelerate the H - ion beam .It can provide 15 mA peak current beam with energy gain from 3 MeV to 80 MeV .It consists of four independent tanks ,of which the average length is about 9 m .Each tank is driven by a 3 MW klystron respec‐tively .Each tank is divided into three short unit sections for ease of fabrication and as‐sembly .The construction of DTL cavity and drift tube is the most critical technical in CSNS .In this paper ,the fabrication process of DTL was introduced ,including the first time to perform copper electroplating with high electrical conductivity in the domestic high intensity beam accelerator ,the design study on the newly developed electro‐magnet coil and the high accuracy magnetic field measurement .The measurement results can satisfy with the physical design .%漂移管直线加速器(DTL)是中国散裂中子源(CSNS)直线加速器的主要部分,负责将脉冲流强为15 mA的负氢离子从3 MeV加速到80 MeV ,再注入到快循环同步加速器(RCS)中实现进一步加速。CSNS DTL由4节长度约9 m的RF腔体组成,单节RF腔体由1台3 MW的速调管提供功率。每节腔体又分为3段长约3 m的机械腔体以便于加工和安装。DTL腔体和漂移管的研制是整个CSNS直线加速器的关键。本文介绍了CSNS DTL研制过程,包括国内首次在强流质子加速器RF腔内表面进行高导无氧铜电镀、新型磁铁线圈的研制、小孔径磁铁的高精度测量等。加工及测试结果均满足CSNS的设计要求。

  14. Study of 232Th(n, γ) and 232Th(n,f) reaction rates in a graphite moderated spallation neutron field produced by 1.6 GeV deuterons on lead target

    Science.gov (United States)

    Asquith, N. L.; Hashemi-Nezhad, S. R.; Westmeier, W.; Zhuk, I.; Tyutyunnikov, S.; Adam, J.

    2015-02-01

    The Gamma-3 assembly of the Joint Institute for Nuclear Research (JINR), Dubna, Russia is designed to emulate the neutron spectrum of a thermal Accelerator Driven System (ADS). It consists of a lead spallation target surrounded by reactor grade graphite. The target was irradiated with 1.6 GeV deuterons from the Nuclotron accelerator and the neutron capture and fission rate of 232Th in several locations within the assembly were experimentally measured. 232Th is a proposed fuel for envisaged Accelerator Driven Systems and these two reactions are fundamental to the performance and feasibility of 232Th in an ADS. The irradiation of the Gamma-3 assembly was also simulated using MCNPX 2.7 with the INCL4 intra-nuclear cascade and ABLA fission/evaporation models. Good agreement between the experimentally measured and calculated reaction rates was found. This serves as a good validation for the computational models and cross section data used to simulate neutron production and transport of spallation neutrons within a thermal ADS.

  15. The design of high power, external antennas for radio frequency multicusp ion sources

    Science.gov (United States)

    Welton, R. F.; Stockli, M. P.; Roseberry, R. T.; Kang, Y.; Keller, R.

    2004-05-01

    The ion source for the Spallation Neutron Source (SNS) is a radio-frequency, multicusp source designed to deliver H- beam pulses of 45 mA to the SNS accelerator, with a pulse length of 1 ms and a repetition rate of 60 Hz. In order to achieve this performance the source must operate with both high peak rf power, ˜45 kW, and high average rf power, ˜3 kW, over an operational run period of 3 weeks. The most critical source component in this respect is the plasma-immersed, porcelain coated rf antenna which can be susceptible to damage during high power operation. The DESY group has developed an external antenna configuration utilizing an Al2O3 plasma chamber which has demonstrated a very long operational period exceeding 25 000 h. Their source operates with peak rf powers comparable to the SNS source but with greatly reduced average rf powers, ˜50 W. In order to explore the applicability of this external antenna concept to high average power ion sources like the SNS source, we have performed thermal, mechanical, and electromagnetic analyses of the Al2O3 plasma chamber. This article discusses the final design which has resulted from these studies as well as estimates of the power limitations of such devices.

  16. Reassessing Power

    Institute of Scientific and Technical Information of China (English)

    CHARLES; K.EBINGER; JOHN; P.BANKS

    2011-01-01

    Fukushima accident increases global concern over nuclear safety The accident at the Fukushima Daiichi Nuclear Power Plant in Japan has had an immediate impact on resurgent interest in nuclear power worldwide.Numerous governments have announced plans to re-examine nuclear energy policy and review the safety of their reactors and the adequacy of their regulatory frameworks.

  17. Power Drain

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Rising coal prices mean dwindling profits for China’s power plants. In some cases,they have forced plants to close their doors If electricity prices were not raised together with fuel prices, the country’spower plants could not survive. This isthe common voice of China’s power plants now.

  18. Power Source

    Science.gov (United States)

    Schooley, Michael L.

    2010-01-01

    Principals are powerful: They are the primary catalysts for creating a lasting foundation for learning, driving school and student performance, and shaping the long-term impact of school improvement efforts. Yet few principals would characterize themselves as powerful. Rather, they're self-effacing, adaptable, pragmatic, and quick to share credit…

  19. Diastatic power

    Science.gov (United States)

    diastatic power: Diastatic power, abbreviated DP, is the total activity of malt starch degrading enzymes that hydrolyze starch to fermentable sugars. The starch degrading enzymes contributing to this process are a-amylase, ß-amylase, limit dextrinase, and a-glucosidase. The driving force for DP a...

  20. Power system

    Science.gov (United States)

    Hickam, Christopher Dale

    2008-03-18

    A power system includes a prime mover, a transmission, and a fluid coupler having a selectively engageable lockup clutch. The fluid coupler may be drivingly connected between the prime mover and the transmission. Additionally, the power system may include a motor/generator drivingly connected to at least one of the prime mover and the transmission. The power-system may also include power-system controls configured to execute a control method. The control method may include selecting one of a plurality of modes of operation of the power system. Additionally, the control method may include controlling the operating state of the lockup clutch dependent upon the mode of operation selected. The control method may also include controlling the operating state of the motor/generator dependent upon the mode of operation selected.

  1. Mitigation of Power Quality Problems in Grid-Interactive Distributed Generation System

    Science.gov (United States)

    Bhende, C. N.; Kalam, A.; Malla, S. G.

    2016-04-01

    Having an inter-tie between low/medium voltage grid and distributed generation (DG), both exposes to power quality (PQ) problems created by each other. This paper addresses various PQ problems arise due to integration of DG with grid. The major PQ problems are due to unbalanced and non-linear load connected at DG, unbalanced voltage variations on transmission line and unbalanced grid voltages which severely affect the performance of the system. To mitigate the above mentioned PQ problems, a novel integrated control of distribution static shunt compensator (DSTATCOM) is presented in this paper. DSTATCOM control helps in reducing the unbalance factor of PCC voltage. It also eliminates harmonics from line currents and makes them balanced. Moreover, DSTATCOM supplies the reactive power required by the load locally and hence, grid need not to supply the reactive power. To show the efficacy of the proposed controller, several operating conditions are considered and verified through simulation using MATLAB/SIMULINK.

  2. Power Talk

    DEFF Research Database (Denmark)

    Liu, Hongpeng; Yang, Yongheng; Loh, Poh Chiang

    2016-01-01

    In this paper, a novel communication strategy called Power Talk is introduced to realize the power line communication among the Voltage Source Converters (VSC) of DC MicroGrids (MGs). Each VSC transmits information by changing the control parameters, and receives information by observing the local...... output power. By using common coding schemes, which transform the DC MGs in some familiar communication channels, some important communication challenges can be addressed, such as random load variations and VSCs switching, as it do not need a separate communication channel. For this purpose, two multiple...

  3. Spallation neutron experiment at SATURNE

    Energy Technology Data Exchange (ETDEWEB)

    Meigo, Shin-ichiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-11-01

    The double differential cross sections for (p,xn) reactions and the spectra of neutrons produced from the thick target have been measured at SATURNE in SACLAY from 1994 to 1997. The status of the experiment and the preliminary experimental results are presented. (author)

  4. Power Preservation

    DEFF Research Database (Denmark)

    Galster, Kjeld

    Power Preservation (Abstract) In the 17th century, just as today, coalitions needed ‘lead nations’. This was assumed to be a power with great military and economic potentials, and Denmark endeavoured to act as such a leader in the Thirty Years War from 1626 to 28. The results were not encouraging...... in the military field and they were disastrous as far as fiscal matters were concerned. Sweden took over the leadership of the protestant side and she took over Denmark’s place amongst the great powers of the Baltic Region. From that time onwards, Danish influence and options on the international stage gradually...... declined. Thus, Denmark of the 17th century is not to be counted amongst the great powers, but since Christian V’s accession to the throne in 1670 Denmark-Norway has developed into one of Europe’s most highly militarised states. Apart from a permanently combat ready navy, the country maintains a standing...

  5. 8 May 2013 - Swedish European Spallation Source Chief Executive Officer J. H. Yeck in the ATLAS visitor centre and experimental cavern with Collaboration Spokesperson D. Charlton (also present M. Nessi, R. Garoby and E. Tsesmelis); signing the guest book with International Relations Adviser E. Tsesmelis.

    CERN Multimedia

    Jean-Claude Gadmer

    2013-01-01

    8 May 2013 - Swedish European Spallation Source Chief Executive Officer J. H. Yeck in the ATLAS visitor centre and experimental cavern with Collaboration Spokesperson D. Charlton (also present M. Nessi, R. Garoby and E. Tsesmelis); signing the guest book with International Relations Adviser E. Tsesmelis.

  6. Introduction to electrical power and power electronics

    CERN Document Server

    Patel, Mukund R

    2012-01-01

    Power Generation, Distribution, and Utilization AC Power Fundamentals Common Aspects of Power Equipments AC Generator AC and DC Motors Transformer Power Cable Power Distribution Fault Current Analysis System ProtectionEconomic Use of PowerElectrochemical BatteryPower Electronics and Motor Drives Power Electronics Devices DC-DC Converters AC-DC-AC Converters Variable-Frequency Drives Quality of Power Power Converter CoolingAppendixIndex

  7. Corrosion mechanism of T91 steel by Pb-Bi eutectic used as spallation target: importance for accelerator driven system; Mecanisme de corrosion de l'acier T91 par l'eutectique Pb-Bi utilise comme materiau de cible de spallation: importance pour les reacteurs hybrides

    Energy Technology Data Exchange (ETDEWEB)

    Martinelli, L

    2005-10-15

    The aim of this work has been to determine the oxidation mechanism of the martensitic steel T91 in the Pb-Bi liquid eutectic alloy, saturated in oxygen, at 470 C, in order to develop a long-term predictive model of the oxidation kinetics of the steel. This work enters in the framework of the lifetime studies of the spallation module demonstrator: MEGAPIE for the researches on hybrid reactors. An experimental characterization of the oxide layers has been carried out as well as the oxidation kinetics of the T91 steel. An oxidation mechanism has been elaborated from these experimental results and then simulated. The oxide layer formed at the T91 surface presents a duplex structure constituted by a magnetite external layer and a spinel Fe-Cr internal layer. A growth mechanism of the oxide layers has been proposed: the growth of the magnetite layer seems to be limited by the iron diffusion in the lattice of the duplex oxide layer. In parallel, an auto-regulation mechanism seems to govern the growth of the Fe-Cr spinel layer. This mechanism includes a non-limiting step of the oxygen diffusion in the oxide layer (by liquid way in the nano-channels of lead), as well as a limiting step of iron diffusion in the lattice of the oxide layer. In considering the proposed oxidation mechanisms, a simulation of the growth of the two oxide layers is carried out and compared to the long-time oxidation growth kinetics. The good agreement between the experimental results allows, finally, to strengthen the proposition of a long-term growth kinetic oxidation mechanism of the oxide layers. (O.M.)

  8. Analysis on the Spallation Drilling Technique and Its Application Prospect in Geothermal Drilling%碎裂钻井技术及其在地热钻井中的应用前景分析

    Institute of Scientific and Technical Information of China (English)

    白占学; 郑秀华; 于进洋

    2013-01-01

      地热资源储量丰富,分布广泛,开发前景广阔。但是在现有地热钻井技术条件下进行地热开发的周期长、成本高,所以亟待钻井技术的突破使巨大的地热资源得到经济有效地开发。碎裂钻井技术是一种采用了新的钻井原理的钻井技术,其能够有效地解决常规钻井过程中经常遇到的诸如在坚硬地层中进尺慢等棘手问题,一旦得到商业化应用,将会对地热资源经济有效地开发产生革命性的影响。在分析常规钻井技术存在的问题的基础上,介绍了碎裂钻井技术的工作原理及碎岩机理,阐明了其优缺点,为该技术在地热钻井中的应用研究提供参考。%There are plenty of geothermal resources widely distributing with broad prospects for development.A new princi-ple of drilling has been introduced in spallation drilling;it can resolve the knotty problems such as slow penetration rate of-ten encountered while drilling in hard rocks.As soon as the technology is put in commercial application, it will have revolu-tionary consequences for the exploitation of geothermal resources.Based on the analysis on the problems in the traditional drilling technology, the working mechanism of spallation drilling is introduced; the advantages and disadvantages are de-scribed.It will provide references to the application of spallation drilling in geothermal development.

  9. High Power Factor Power Design

    Directory of Open Access Journals (Sweden)

    Zhang Jing-yi

    2013-07-01

    Full Text Available The PFC circuit takes UCC28019 made by TI Company as the core of system control, realize the power factor correction circuit functions, and the circuit power factor can be measured. Through a variety of detection circuit, with the support SCM control. And 30V~36V output voltage regulator can be set; with over-current protection circuits function, and be able to automatically back. Output current, voltage, and little significant value are displayed by display modules.

  10. Power Down

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ Cai Wending and his colleague Xie Changsheng have been living out of a suitcase for the past two months.The pair,managers at a coal-fired power plant in Hunan Province,have been staying in a modest three-star hotel in Jincheng,a small city in Shanxi Province.They are not the only long-term residents of the hotel.Numerous power plant officials have been drawn to Jincheng from across China,all for the same purpose-to buy coal.

  11. Powering up

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    China building the world’s first third-generation nuclear power plants based on American technology Almost 30 years ago, a partial core meltdown occurred in one of the two nuclear reactors at Three Mile llsland Nuclear Generating Station in

  12. Comic Power

    DEFF Research Database (Denmark)

    Tønder, Lars

    2014-01-01

    by skepticism about the enduring contributions of comic acts, and it then goes on to suggest that we turn to an alternative trajectory in democratic theory, one that encourages us to focus on the empowering and pluralizing potential embedded in what I name “comic power.” The wager is that attention...

  13. Power Play

    Institute of Scientific and Technical Information of China (English)

    BRADLEY GARDNER

    2008-01-01

    @@ Bill Emmott's new book,Rivals:How the Power Struggle Between China,India and Japan Will Shape Our Next Decade,is an investigation of the problematic relationship between China,India,and Japan,as two of those countries begin to assert themselves on the world stage,and how the situation could result in all-out conflict.

  14. Power Talk

    DEFF Research Database (Denmark)

    Stefanovic, Cedomir; Popovski, Petar; Angjelichinoski, Marko

    2015-01-01

    , while it is received by processing the bus measurements that units perform. This implies that the communication does not require a dedicated modem, but instead it is piggybacked on top of the power electronics. The communication is challenged by the random fluctuations of the voltage level due...

  15. Power semiconductors

    CERN Document Server

    Kubát, M

    1984-01-01

    The book contains a summary of our knowledge of power semiconductor structures. It presents first a short historic introduction (Chap. I) as well as a brief selection of facts from solid state physics, in particular those related to power semiconductors (Chap. 2). The book deals with diode structures in Chap. 3. In addition to fundamental facts in pn-junction theory, the book covers mainly the important processes of power structures. It describes the emitter efficiency and function of microleaks (shunts). the p +p and n + n junctions, and in particular the recent theory of the pin, pvn and p1tn junctions, whose role appears to be decisive for the forward mode not only of diode structures but also of more complex ones. For power diode structures the reverse mode is the decisive factor in pn-junction breakdown theory. The presentation given here uses engineering features (the multiplication factor M and the experimentally detected laws for the volume and surface of crystals), which condenses the presentation an...

  16. POWER FUNCTIONS

    Institute of Scientific and Technical Information of China (English)

    王雷

    2008-01-01

    <正>A power function of degree n is a function of the form f(x)=ax~n.For large n,it appears that the graph coincide with the x-axis near the origin,but it does not;the graph actually touches the x—axis only at the origin.

  17. Power Shift

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ "We are entering a new era of world history: the end of Western domination and the arrival of the Asian century. The question is: will Washington wake up to this reality?" This is the central premise of Kishore Mahbubani's provocative new book The New Asian Hemisphere: The Irresistible Shift of Global Power to the East.

  18. Power branding

    Energy Technology Data Exchange (ETDEWEB)

    Chambers, A.

    1998-12-31

    For most of its century-long history, electricity was a natural monopoly, due in part to the excessive cost of the necessary infrastructure. In the past decade, however, politics have pushed the industry toward competition and consumer choice. At the same time, technology has been developed that allows consumers to choose their electricity supplier and to track the flow of power through the various grids and lines. In her new book, Power Branding, author and industry expert Ann Chambers examines marketing and branding of electricity -- what it is, how it`s done, what its benefits are for electric utilities, marketers, and even natural gas companies allied with the utilities. She surveys industry leaders who have already taken a dive into the ocean of marketing and offers lessons drawn from their experiences. She also takes a look at other formerly regulated industries -- airlines, telephone, natural gas -- and describes how their rebirth as free-market industries may affect the course of the electric utility industry`s experience. The contents include: Introduction; Basics of branding: Brand image; Value-added services; Southern Company; Duke Energy; UtiliCorp/EnergyOne/Aquila--big and brand; Engage energy; Florida Power and Light Co.; Enron; Convergence; Lessons from the natural gas industry; Lessons from other industries; Conclusion; Resources; Glossary of branding, marketing and Btu convergence; and Major federal legislation affecting the electric power industry.

  19. Study of the fragment distribution in the spallation reaction Fe + p for 5 energies from 300 to 1500 MeV/A and application to the determination of damage on an hybrid system window; Etude de la production des noyaux residuels dans la reaction de spallation Fe+p a 5 energies (300-1500 MeV/ A) et application au calcul de dommages sur une fenetre de systeme hybride

    Energy Technology Data Exchange (ETDEWEB)

    Villagrasa-Canton, C

    2003-12-01

    The window is a crucial part in an accelerator-driven sub-critical reactor: it has to sustain the vacuum of the accelerator body and it has to act as a containment barrier for the core of the reactor. The window undergoes both thermal strains due to the energy loss of the intense proton beam and radiation damages through nuclear reactions induced by protons and by the neutrons back-scattered from the reactor. The window is expected to be made of 90% of iron. The major contribution of this work is the measurement of the isotope production cross-section of the spallation reaction on Fe-56 for 5 energies from 300 to 1500 MeV/A and for Z > 7, the distribution of recoil speeds of fragments has also been measured. The first chapter is dedicated to the specificities of spallation reactions and their simulation through mathematical models. The second chapter presents the experimental setting, the reverse kinematics method has been used: it is a beam of Fe-56 that is impinging on an hydrogen target. The third chapter deals with the analysis process that has led to the values of cross-sections and of speed distributions. The fourth chapter presents a comparison of these results, first with already existing experimental data in overlapping domains and secondly with the models presented in the first chapter. It appears that the agreement is better for cross-sections than for speed distributions. The last chapter shows how these new data about iron can be applied to the assessment of critical issues concerning the window: -) the pile-up of fragments during irradiation time and -) the determination of dpa (displacement per atom). (A.C.)

  20. Laser Drilling - Drilling with the Power of Light

    Energy Technology Data Exchange (ETDEWEB)

    Brian C. Gahan; Samih Batarseh

    2004-09-28

    Gas Technology Institute (GTI) has been the leading investigator in the field of high power laser applications research for well construction and completion applications. Since 1997, GTI (then as Gas Research Institute) has investigated several military and industrial laser systems and their ability to cut and drill into reservoir type rocks. In this report, GTI continues its investigation with a recently acquired 5.34 kW ytterbium-doped multi-clad high power fiber laser (HPFL). The HPFL represents a potentially disruptive technology that, when compared to its competitors, is more cost effective to operate, capable of remote operations, and requires considerably less maintenance and repair. To determine how this promising laser compares with other lasers used in past experimental work, GTI performed a number of experiments with results directly comparable to previous data. Experiments were designed to investigate the effect of laser input parameters on representative reservoir rock types of sandstone and limestone. The focus of the experiments was on completion and perforation applications, although the results and techniques apply to well construction and other rock cutting applications. Variables investigated include laser power, beam intensity, external purging of cut materials, sample orientation, beam duration, beam shape, and beam frequency. The investigation also studied the thermal effects on the two sample rock types and their methods of destruction: spallation for sandstone, and thermal dissociation for limestone. Optimal operating conditions were identified for each rock type and condition. As a result of this experimental work, the HPFL has demonstrated a better capability of cutting and drilling limestone and sandstone when compared with other military and industrial lasers previously tested. Consideration should be given to the HPFL as the leading candidate for near term remote high power laser applications for well construction and completion.

  1. High power ring methods and accelerator driven subcritical reactor application

    Energy Technology Data Exchange (ETDEWEB)

    Tahar, Malek Haj [Univ. of Grenoble (France)

    2016-08-07

    High power proton accelerators allow providing, by spallation reaction, the neutron fluxes necessary in the synthesis of fissile material, starting from Uranium 238 or Thorium 232. This is the basis of the concept of sub-critical operation of a reactor, for energy production or nuclear waste transmutation, with the objective of achieving cleaner, safer and more efficient process than today’s technologies allow. Designing, building and operating a proton accelerator in the 500-1000 MeV energy range, CW regime, MW power class still remains a challenge nowadays. There is a limited number of installations at present achieving beam characteristics in that class, e.g., PSI in Villigen, 590 MeV CW beam from a cyclotron, SNS in Oakland, 1 GeV pulsed beam from a linear accelerator, in addition to projects as the ESS in Europe, a 5 MW beam from a linear accelerator. Furthermore, coupling an accelerator to a sub-critical nuclear reactor is a challenging proposition: some of the key issues/requirements are the design of a spallation target to withstand high power densities as well as ensure the safety of the installation. These two domains are the grounds of the PhD work: the focus is on the high power ring methods in the frame of the KURRI FFAG collaboration in Japan: upgrade of the installation towards high intensity is crucial to demonstrate the high beam power capability of FFAG. Thus, modeling of the beam dynamics and benchmarking of different codes was undertaken to validate the simulation results. Experimental results revealed some major losses that need to be understood and eventually overcome. By developing analytical models that account for the field defects, one identified major sources of imperfection in the design of scaling FFAG that explain the important tune variations resulting in the crossing of several betatron resonances. A new formula is derived to compute the tunes and properties established that characterize the effect of the field imperfections on the

  2. Poultry power

    Energy Technology Data Exchange (ETDEWEB)

    Loram, G.

    2000-02-01

    This article gives details of the world's largest power plant fired by poultry litter and forestry waste fired in Thetford, UK. The processing of the waste, the injection of the waste by air, the plant operation, and the cleaning of the flue gas are described. The low levels of odour and noise, and the environmental benefits of the plant which produces no methane or carbon dioxide emissions are noted. (uk)

  3. Cyber Power

    Science.gov (United States)

    2010-05-01

    attributed to “patriotic hackers” in Russia who were offended by Estonia’s movement of a World War II monument to Soviet soldiers. In 2008, shortly...internet to mobilize Chinese students to demonstrate against Japan when its officials took positions that offended Chinese views of the 1930s...reduction of power differentials among them. Anyone from a teen age hacker to a major modern government can do damage in cyber space, and as the famous New

  4. Suntech Power

    Institute of Scientific and Technical Information of China (English)

    BRAKLEY GARDNER

    2008-01-01

    @@ Why the new US president could provide a boost for China's largest solar firm Back in the glory days of China investing, Suntech Power (尚德太阳能电力), China's largest solar com-pany, benefited from both inves-tor interest during China's stock market boom, and the growing demand for solar technologies worldwide, as governments be-gan implementing a raft of new measures providing assistance to renewable energy companies.

  5. BRICS Power

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    When Goldman Sachs economist Jim O’Neill coined the acronym BRIC to describe collectively Brazil,Russia,India and China,the world mainly regarded it as one of the easy-come,easy-go terms in economics.A decade later,O’Neill’s concept is not forgotten.It is successfully playing an historic role in representing the shift in global economic power away

  6. RF power coupling for the CSNS DTL

    Institute of Scientific and Technical Information of China (English)

    刘华昌; 彭军; 殷学军; 欧阳华甫; 傅世年

    2011-01-01

    The China Spallation Neutron Source (CSNS) drift tube linac (DTL) consists of four tanks and each tank is fed by a 2.5 MW klystron. Accurate predication of RF coupling between the RF cavity and ports is very important for DTL RF coupler design. An iris-ty

  7. Probability of islanding in utility networks due to grid connected photovoltaic power systems

    Energy Technology Data Exchange (ETDEWEB)

    Verhoeven, B.

    2002-09-15

    This report for the International Energy Agency (IEA) made by Task 5 of the Photovoltaic Power Systems (PVPS) programme takes a look at the probability of islanding in utility networks due to grid-connected photovoltaic power systems. The mission of the Photovoltaic Power Systems Programme is to enhance the international collaboration efforts which accelerate the development and deployment of photovoltaic solar energy. Task 5 deals with issues concerning grid-interconnection and distributed PV power systems. This report summarises the results on a study on the probability of islanding in power networks with a high penetration level of grid connected PV-systems. The results are based on measurements performed during one year in a Dutch utility network. The measurements of active and reactive power were taken every second for two years and stored in a computer for off-line analysis. The area examined and its characteristics are described, as are the test set-up and the equipment used. The ratios between load and PV-power are discussed. The general conclusion is that the probability of islanding is virtually zero for low, medium and high penetration levels of PV-systems.

  8. Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux

    Science.gov (United States)

    Bowman, Charles D.

    1992-01-01

    Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux. High thermal neutron fluxes generated from the action of a high power proton accelerator on a spallation target allows the efficient burn-up of higher actinide nuclear waste by a two-step process. Additionally, rapid burn-up of fission product waste for nuclides having small thermal neutron cross sections, and the practicality of small material inventories while achieving significant throughput derive from employment of such high fluxes. Several nuclear technology problems are addressed including 1. nuclear energy production without a waste stream requiring storage on a geological timescale, 2. the burn-up of defense and commercial nuclear waste, and 3. the production of defense nuclear material. The apparatus includes an accelerator, a target for neutron production surrounded by a blanket region for transmutation, a turbine for electric power production, and a chemical processing facility. In all applications, the accelerator power may be generated internally from fission and the waste produced thereby is transmuted internally so that waste management might not be required beyond the human lifespan.

  9. Power optics

    Energy Technology Data Exchange (ETDEWEB)

    Apollonov, V V [A M Prokhorov General Physics Institute, Russian Academy of Sciences, Moscow (Russian Federation)

    2014-02-28

    By using the theory we developed in the early 1970s, a broad range of phenomena is considered for an optical surface of a solid body that is exposed to radiation arbitrarily varying in time and producing temperature fields, thermoelastic stresses and thermal deformations on the surface layer. The examination is based on the relations (which are similar to Duhamel's integral formula from the theory of heat conduction) between the quantities characterising the thermal stress state in any nonstationary regimes of energy input into a solid. A peculiar feature of the analysis of the thermal stress state in this case consists in the fact that this relation comprises time as a parameter, which in turn is a consequence of incoherence of the quasi-stationary problem of thermoelasticity. This phenomenon is particularly important for the optics of high-power, high-pulse repetition rate lasers, which are being actively developed. In the review, we have recently published in Laser Physics, the thermal stress state of a solid is analysed. In this state, time is treated as an independent variable used in differentiation. Such an approach greatly reduces the applicability of the method. The review published contains data on the use of capillary porous structures made of various materials with different degrees of the surface development. Moreover, such structures can be efficiently employed to increase the heat exchange at a temperature below the boiling point of the coolant. In the present review we discuss the dependences of the limiting laser intensities on the duration of a pulse or a pulse train, corresponding to the three stages of the state of the reflecting surface and leading to unacceptable elastic deformations of the surface, to the plastic yield of the material accompanied by the formation of residual stresses and to the melting of the surface layer. We also analyse the problem of heat exchange in the surface layer with a liquid metal coolant pumped through it

  10. Power optics

    Science.gov (United States)

    Apollonov, V. V.

    2014-02-01

    By using the theory we developed in the early 1970s, a broad range of phenomena is considered for an optical surface of a solid body that is exposed to radiation arbitrarily varying in time and producing temperature fields, thermoelastic stresses and thermal deformations on the surface layer. The examination is based on the relations (which are similar to Duhamel's integral formula from the theory of heat conduction) between the quantities characterising the thermal stress state in any nonstationary regimes of energy input into a solid. A peculiar feature of the analysis of the thermal stress state in this case consists in the fact that this relation comprises time as a parameter, which in turn is a consequence of incoherence of the quasi-stationary problem of thermoelasticity. This phenomenon is particularly important for the optics of high-power, high-pulse repetition rate lasers, which are being actively developed. In the review, we have recently published in Laser Physics, the thermal stress state of a solid is analysed. In this state, time is treated as an independent variable used in differentiation. Such an approach greatly reduces the applicability of the method. The review published contains data on the use of capillary porous structures made of various materials with different degrees of the surface development. Moreover, such structures can be efficiently employed to increase the heat exchange at a temperature below the boiling point of the coolant. In the present review we discuss the dependences of the limiting laser intensities on the duration of a pulse or a pulse train, corresponding to the three stages of the state of the reflecting surface and leading to unacceptable elastic deformations of the surface, to the plastic yield of the material accompanied by the formation of residual stresses and to the melting of the surface layer. We also analyse the problem of heat exchange in the surface layer with a liquid metal coolant pumped through it. The

  11. Wind Power - A Power Source Enabled by Power Electronics

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Chen, Zhe

    2004-01-01

    . The deregulation of energy has lowered the investment in bigger power plants, which means the need for new electrical power sources may be very high in the near future. Two major technologies will play important roles to solve the future problems. One is to change the electrical power production sources from...... electronics is changing from being a minor energy source to be acting as an important power source. By that wind power is also getting an added value....

  12. Power management system

    Science.gov (United States)

    Algrain, Marcelo C.; Johnson, Kris W.; Akasam, Sivaprasad; Hoff, Brian D.

    2007-10-02

    A method of managing power resources for an electrical system of a vehicle may include identifying enabled power sources from among a plurality of power sources in electrical communication with the electrical system and calculating a threshold power value for the enabled power sources. A total power load placed on the electrical system by one or more power consumers may be measured. If the total power load exceeds the threshold power value, then a determination may be made as to whether one or more additional power sources is available from among the plurality of power sources. At least one of the one or more additional power sources may be enabled, if available.

  13. Progress on the 140 KV, 10 Megawatt Peak, 1 Megawatt Average Polyphase Quasi-Resonant Bridge, Boost Converter/Modulator for the Spallation Neutron Source (SNS) Klystron Power System

    CERN Document Server

    Reass, W A; Gribble, R F; Lynch, M T; Tallerico, P J; Reass, William A.; Doss, James D.; Gribble, Robert F.; Lynch, Michael T.; Tallerico, Paul J.

    2000-01-01

    This paper describes electrical design and operational characteristics of a zero-voltage-switching 20 kHz polyphase bridge, boost converter/modulator for klystron pulse application. The DC-DC converter derives the buss voltages from a standard 13.8 kV to 2300 Y substation cast-core transformer. Energy storage and filtering is provided by self-clearing metallized hazy polypropylene traction capacitors. Three "H-Bridge" IGBT switching networks are used to generate the polyphase 20 kHz transformers primary drive waveforms. The 20 kHz drive waveforms are chirped the appropriate duration to generate the desired klystron pulse width. PWM (pulse width modulation) of the individual 20 kHz pulses is utilized to provide regulated output waveforms with adaptive feedforward and feedback techniques. The boost transformer design utilizes amorphous nanocrystalline material that provides the required low core loss at design flux levels and switching frequencies. Resonant shunt peaking is used on the transformer secondary to ...

  14. Narrow linewidth picosecond UV pulsed laser with mega-watt peak power.

    Science.gov (United States)

    Huang, Chunning; Deibele, Craig; Liu, Yun

    2013-04-08

    We demonstrate a master oscillator power amplifier (MOPA) burst mode laser system that generates 66 ps/402.5 MHz pulses with mega-watt peak power at 355 nm. The seed laser consists of a single frequency fiber laser (linewidth picosecond pulse generator, and a fiber based preamplifier. A very high extinction ratio (45 dB) has been achieved by using an adaptive bias control of the EOM. The multi-stage Nd:YAG amplifier system allows a uniformly temporal shaping of the macropulse with a tunable pulse duration. The light output from the amplifier is converted to 355 nm, and over 1 MW peak power is obtained when the laser is operating in a 5-μs/10-Hz macropulse mode. The laser output has a transform-limited spectrum with a very narrow linewidth of individual longitudinal modes. The immediate application of the laser system is the laser-assisted hydrogen ion beam stripping for the Spallation Neutron Source (SNS).

  15. Accelerator-Driven Subcritical Fission in a Molten Salt Core: Green Nuclear Power for the New Millennium

    Science.gov (United States)

    McIntyre, Peter

    2011-10-01

    Scientists at Texas A&M University, Brookhaven National Lab, and Idaho National Lab are developing a design for accelerator-drive subcritical fission in a molten salt core (ADSMS). Three high-power proton beams are delivered to spallation targets in a molten salt core, where they provide ˜3% of the fast neutrons required to sustain 600 MW of fission. The proton beams are produced by a flux-coupled stack of superconducting strong-focusing cyclotrons. The fuel consists of a eutectic of sodium chloride with either spent nuclear fuel from a conventional U power reactor (ADSMS-U) or thorium (ADSMS-Th). The subcritical core cannot go critical under any failure mode. The core cannot melt down even if all power is suddenly lost to the facility for a prolonged period. The ultra-fast neutronics of the core makes it possible to operate in an isobreeding mode, in which neutron capture breeds the fertile nuclide into a fissile nuclide at the same rate that fission burns the fissile nuclide, and consumes 90% of the fertile inventory instead of the 5% consumed in the original use in a conventional power plant. The ultra-fast neutronics produces a very low equilibrium inventory of the long-lived minor actinides, ˜10^4 less than what is produced in conventional power plants. ADSMS offers a method to safely produce the energy needs for all mankind for the next 3000 years.

  16. Power Sources for Ultra Low Power Electronics

    Science.gov (United States)

    2000-06-12

    DARPA asked JASON to examine the issue of power sources for low power electronics with a specific emphasis on the properties of nuclear batteries and...integrated power sources combining power and electronics. During the 1998 Summer Study a workshop was held to provide background for the study, with

  17. Power theories for improved power quality

    CERN Document Server

    Pasko, Marian

    2012-01-01

    Power quality describes a set of parameters of electric power and the load’s ability to function properly under specific conditions. It is estimated that problems relating to power quality costs the European industry hundreds of billions of Euros annually. In contrast, financing for the prevention of these problems amount to fragments of these costs. Power Theories for Improved Power Quality addresses this imbalance by presenting and assessing a range of methods and problems related to improving the quality of electric power supply. Focusing particularly on active compensators and the DSP based control algorithms, Power Theories for Improved Power Quality introduces the fundamental problems of electrical power. This introduction is followed by chapters which discuss: •‘Power theories’ including their historical development and application to practical problems, •operational principles of active compensator’s DSP control based algorithms using examples and results from laboratory research, and •t...

  18. Women, Power, and Libraries.

    Science.gov (United States)

    Schuman, Patricia Glass

    1984-01-01

    Discusses the concept of power in the context of women and the library profession, citing views of power by Max Weber, John Kenneth Galbraith, Letty Cottin Pogrebin, and Rosabeth Moss Kantor. Male power and female submission, defining power, organizing for power, and sharing power are highlighted. A 12-item bibliography is included. (EJS)

  19. Wind power - a power source now enabled by power electronics

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Iov, Florin

    2007-01-01

    energy at the end-user should be set up. Deregulation of energy has lowered the investment in larger power plants, which means the need for new electrical power sources may be increased in the near future. Two major technologies will play important roles to solve the future problems. One is to change...... the electrical power production sources from the conventional, fossil (and short term) based energy sources to renewable energy resources. Another is to use high efficient power electronics in power generation, power transmission/distribution and end-user application. This paper discuss the most emerging...... renewable energy sources, wind energy, which by means of power electronics are changing from being minor energy sources to be acting as important power sources in the energy system....

  20. Wind power - a power source now enabled by power electronics

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Iov, Florin

    2007-01-01

    energy at the end-user should be set up. Deregulation of energy has lowered the investment in larger power plants, which means the need for new electrical power sources may be increased in the near future. Two major technologies will play important roles to solve the future problems. One is to change...... renewable energy sources, wind energy, which by means of power electronics are changing from being minor energy sources to be acting as important power sources in the energy system....

  1. Dynamic power flow controllers

    Science.gov (United States)

    Divan, Deepakraj M.; Prasai, Anish

    2017-03-07

    Dynamic power flow controllers are provided. A dynamic power flow controller may comprise a transformer and a power converter. The power converter is subject to low voltage stresses and not floated at line voltage. In addition, the power converter is rated at a fraction of the total power controlled. A dynamic power flow controller controls both the real and the reactive power flow between two AC sources having the same frequency. A dynamic power flow controller inserts a voltage with controllable magnitude and phase between two AC sources; thereby effecting control of active and reactive power flows between two AC sources.

  2. Power electronics for low power arcjets

    Science.gov (United States)

    Hamley, John A.; Hill, Gerald M.

    1991-01-01

    In anticipation of the needs of future light-weight low-power spacecraft, arcjet power electronics in the 100- to 400-W operating range were developed. Power topologies similar to those in the higher 2-kW and 5- to 30-kW power range were implemented, including a four-transistor bridge-switching circuit, current-mode pulse-width modulated control, and an output current averaging inductor with an integral pulse generation winding. Reduction of switching transients was accomplished using a low inductance power distribution network, and no passive snubber circuits were necessary for power switch protection. Phase shift control of the power bridge was accomplished using an improved pulse width modulation to phase shift converter circuit. These features, along with conservative magnetics designs, allowed power conversion efficiencies of greater than 92.5 percent to be achieved into resistive loads over the entire operating range of the converter.

  3. Hardware Accelerated Power Estimation

    CERN Document Server

    Coburn, Joel; Raghunathan, Anand

    2011-01-01

    In this paper, we present power emulation, a novel design paradigm that utilizes hardware acceleration for the purpose of fast power estimation. Power emulation is based on the observation that the functions necessary for power estimation (power model evaluation, aggregation, etc.) can be implemented as hardware circuits. Therefore, we can enhance any given design with "power estimation hardware", map it to a prototyping platform, and exercise it with any given test stimuli to obtain power consumption estimates. Our empirical studies with industrial designs reveal that power emulation can achieve significant speedups (10X to 500X) over state-of-the-art commercial register-transfer level (RTL) power estimation tools.

  4. Switching power converters medium and high power

    CERN Document Server

    Neacsu, Dorin O

    2013-01-01

    An examination of all of the multidisciplinary aspects of medium- and high-power converter systems, including basic power electronics, digital control and hardware, sensors, analog preprocessing of signals, protection devices and fault management, and pulse-width-modulation (PWM) algorithms, Switching Power Converters: Medium and High Power, Second Edition discusses the actual use of industrial technology and its related subassemblies and components, covering facets of implementation otherwise overlooked by theoretical textbooks. The updated Second Edition contains many new figures, as well as

  5. Electrical Power Converter

    NARCIS (Netherlands)

    Ferreira, J.A.

    2014-01-01

    Electrical power converter for converting electrical power of a power source connected or connectable at an input to electrical DC-power at an output, wherein between the input and the output a first circuit of submodules is provided, wherein said first circuit of submodules and the power source for

  6. Power flow controller

    NARCIS (Netherlands)

    Ferreira, J.A.; Yuan, Z.; De Haan, S.W.H.

    2008-01-01

    The invention relates to a power flow controller, comprising at least one first converter coupled with a power transmission line, and at least one second converter coupled with a power source, wherein said power source operates at a predeter-mined first frequency and connects to the power transmissi

  7. Power Quality Experimental Analysis on Rural Home Grid-Connected PV Systems

    Directory of Open Access Journals (Sweden)

    Rita Jorge Cerqueira Pinto

    2015-01-01

    Full Text Available Microgeneration is the small-scale generation of heat or electric power or both, by individuals or buildings to meet their own needs. Recently, microgeneration is being regarded as a means to decentralize the power production of renewable energies, reducing the impacts on the grid caused by unexpected energy demands. Given the increase in microgeneration facilities, determining the quantity of energy produced and the power quality assumes growing importance in low, medium, or high voltage facilities. This paper presents a power quality analysis of two different facilities with photovoltaic generation localized in a rural area of Portugal, describing the voltage and frequency behaviour, the harmonic contents, and the total harmonic distortion. Statistical data are presented regarding the number of voltage events and occurrence of dips and swells in both facilities as a percentage of rated voltage. We conclude that some PV systems can severely affect voltage quality, forcing the grid to work at and even above the maximum voltage standard limit.

  8. Wind Power - A Power Source Enabled by Power Electronics

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Chen, Zhe

    2004-01-01

    The global electrical energy consumption is still rising and there is a steady demand to increase the power capacity. The production, distribution and the use of the energy should be as technological efficient as possible and incentives to save energy at the end-user should be set up. The deregul......The global electrical energy consumption is still rising and there is a steady demand to increase the power capacity. The production, distribution and the use of the energy should be as technological efficient as possible and incentives to save energy at the end-user should be set up....... The deregulation of energy has lowered the investment in bigger power plants, which means the need for new electrical power sources may be very high in the near future. Two major technologies will play important roles to solve the future problems. One is to change the electrical power production sources from...... the conventional, fossil (and short term) based energy sources to renewable energy sources. The other is to use high efficient power electronics in power systems, power production and end-user application. This paper discuss the most emerging renewable energy source, wind energy, which by means of power...

  9. Wind power in modern power systems

    DEFF Research Database (Denmark)

    Chen, Zhe

    2013-01-01

    In recent years, wind power is experiencing a rapid growth, and large-scale wind turbines/wind farms have been developed and connected to power systems. However, the traditional power system generation units are centralized located synchronous generators with different characteristics compared...... with wind turbines. This paper presents an overview of the issues about integrating large-scale wind power plants into modern power systems. Firstly, grid codes are introduced. Then, the main technical problems and challenges are presented. Finally, some possible technical solutions are discussed....

  10. Kansas Power Plants

    Data.gov (United States)

    Kansas Data Access and Support Center — The Kansas Power Plants database depicts, as point features, the locations of the various types of power plant locations in Kansas. The locations of the power plants...

  11. Power and Control in Kathmandu: A Comparison of Attempted Power, Actual Power, and Achieved Power.

    Science.gov (United States)

    Emery, Clifton R; Thapa, Sirjana; Wu, Shali

    2016-05-05

    We argue that the concept of power has been inadvertently sidelined in recent theory and research on husband violence. Three types of relationship power may matter with respect to husband violence: attempted power, actual power, and achieved power. Analyses of a randomly selected representative sample of 270 married or partnered women in Kathmandu showed that actual power was related to husband violence prevalence, severity, and injury. Achieved power was related to husband violence prevalence and severity, and attempted power was related to husband violence injury. Implications are discussed.

  12. Power Service Shops

    Data.gov (United States)

    Federal Laboratory Consortium — TVA's Power Service Shops provides expert repair and maintenance of power system components and large industrial equipment. With world-class maintenance facilities...

  13. Human Power Empirically Explored

    NARCIS (Netherlands)

    Jansen, A.J.

    2011-01-01

    Harvesting energy from the users’ muscular power to convert this into electricity is a relatively unknown way to power consumer products. It nevertheless offers surprising opportunities for product designers; human-powered products function independently from regular power infrastructure, are conven

  14. Wind Power Now!

    Science.gov (United States)

    Inglis, David Rittenhouse

    1975-01-01

    The government promotes and heavily subsidizes research in nuclear power plants. Federal development of wind power is slow in comparison even though much research with large wind-electric machines has already been conducted. Unless wind power programs are accelerated it will not become a major energy alternative to nuclear power. (MR)

  15. Wind Power Now!

    Science.gov (United States)

    Inglis, David Rittenhouse

    1975-01-01

    The government promotes and heavily subsidizes research in nuclear power plants. Federal development of wind power is slow in comparison even though much research with large wind-electric machines has already been conducted. Unless wind power programs are accelerated it will not become a major energy alternative to nuclear power. (MR)

  16. Distributed Power Flow Controller

    NARCIS (Netherlands)

    Yuan, Z.

    2010-01-01

    In modern power systems, there is a great demand to control the power flow actively. Power flow controlling devices (PFCDs) are required for such purpose, because the power flow over the lines is the nature result of the impedance of each line. Due to the control capabilities of different types of P

  17. Distributed Power Flow Controller

    NARCIS (Netherlands)

    Yuan, Z.

    2010-01-01

    In modern power systems, there is a great demand to control the power flow actively. Power flow controlling devices (PFCDs) are required for such purpose, because the power flow over the lines is the nature result of the impedance of each line. Due to the control capabilities of different types of P

  18. Power oscillation damping controller

    DEFF Research Database (Denmark)

    2012-01-01

    A power oscillation damping controller is provided for a power generation device such as a wind turbine device. The power oscillation damping controller receives an oscillation indicating signal indicative of a power oscillation in an electricity network and provides an oscillation damping control...

  19. Optimal Power Flow with Power Flow Routers

    OpenAIRE

    2016-01-01

    Power flow routing is an emerging control paradigm for the dynamic control of electric power flows. In this paper, we propose a generic model of a power flow router (PFR) and incorporate it into the optimal power flow (OPF) problem. First, a generic PFR architecture is proposed to encapsulate the desired functions of PFRs. Then, the load flow model of PFRs is developed and incorporated into the OPF framework. To pursue global optimality of the non-convex PFR-incorporated OPF (PFR-OPF) problem...

  20. The electric power engineering handbook power systems

    CERN Document Server

    2012-01-01

    Power Systems, Third Edition (part of the five-volume set, The Electric Power Engineering Handbook) covers all aspects of power system protection, dynamics, stability, operation, and control. Under the editorial guidance of L.L. Grigsby, a respected and accomplished authority in power engineering, and section editors Andrew Hanson, Pritindra Chowdhuri, Gerry Sheble, and Mark Nelms, this carefully crafted reference includes substantial new and revised contributions from worldwide leaders in the field. This content provides convenient access to overviews and detailed information on a diverse arr