Two-dimensional analysis of limiter/divertor transition in scrape-off layer plasmas

International Nuclear Information System (INIS)

Ueda, N.; Itoh, K.; Itoh, S.I.

1989-01-01

The structures of scrape-off layer and divertor plasmas have been studied numerically with a neutral code and a two-dimensional fluid code. Doublet-III is taken as an example for an open divertor configuration. A decisive parameter is the distance between the plasma surface (determined by the magnetic separatrix) and the limiter, which is varied in order to assess the interaction of the plasma with the limiter as well as the effect of neutrals on the main plasma. The minimum value of the limiter clearance needed to prevent plasma-limiter interaction is determined. The scaling of the edge temperature and the dependence of the e-folding length of the scrape-off layer plasma on the heating power are obtained. (author). 16 refs, 17 figs

Plasma motion in the scrape-off layer of a nonequipotential tokamak limiter

International Nuclear Information System (INIS)

Fidel'man, G.N.

1987-01-01

A theory is derived for the laminar convection of the plasma in the scrape-off layer of a poloidal limiter with a distributed potential. The plasma potential and density distributions are derived for the cases of poloidal and slightly nonuniform radial distributions of the potential on the limiter. The stability of these solutions against flute perturbations is analyzed. Criteria for the control of the density profile are derived in the models of laminar and turbulent scrape-off layers. The energy expended in sustaining the limiter potential distribution is studied. If a suitable potential distribution is selected, it is possible to obtain ∼10% of the total convective heat flux from the plasma column in the form of purely electrical energy

Dynamics of impurities in the scrape-off layer

International Nuclear Information System (INIS)

Stangeby, P.C.; Commission of the European Communities, Abingdon

1988-01-01

Impurity modelling of the Scrape-Off Layer, SOL, is reviewed. Simple analytic models are sometimes adequate for relating central impurity levels to edge plasma conditions and for explaining the patterns of net erosion/deposition found on limiters. More sophisticated approaches, which are also necessary, are categorized and reviewed. A plea is made for the acquisition of a more comprehensive data base of edge plasma properties since reliable impurity modelling appears to be dependent on more extensive use of experimental input. (author)

Scrape-off layer flows in the Tore Supra tokamak

International Nuclear Information System (INIS)

Gunn, J.P.; Loarer, T.; Saint-Laurent, F.; Bucalossi, J.; Devynck, P.; Hertout, P.; Moreau, P.; Nanobashvili, I.; Rimini, F.; Duran, I.; Fuchs, V.; Panek, R.; Stockel, J.; Adamek, J.; Dejarnac, R.; Hron, M.; Sarkissian, A.

2005-01-01

Near-sonic parallel flows are systematically observed in the scrape-off layer (SOL) of the limiter tokamak Tore Supra, as in many X-point divertor tokamaks. The poloidal variation of the Mach number of the parallel flow has been measured by moving the contact point of a small circular plasma onto limiters at different poloidal angles. The resulting variations of flow are consistent with the existence of a poloidally nonuniform core-to-SOL out-flux concentrated near the outboard midplane. Strong variations of the SOL width up to a factor of 10 suggest that this localized out-flux is due to enhanced radial transport. The plasma that gets ejected into the SOL can expand radially to the wall if magnetic field lines have long connection lengths and pass unobstructed across the outboard midplane. (authors)

Far scrape-off layer particle and heat fluxes in high density

DEFF Research Database (Denmark)

Müller, H. W.; Bernert, M.; Carralero, D.

2014-01-01

The far scrape-off layer transport is studied in ASDEX Upgrade H-mode discharges with high divertor neutral density N0,div, high power across the separatrix Psep and nitrogen seeding to control the divertor temperature. Such conditions are expected for ITER but usually not investigated in terms...

Scrape-off layer flows in the Tore Supra tokamak

Czech Academy of Sciences Publication Activity Database

Gunn, J. P.; Boucher, C.; Dionne, M.; Ďuran, Ivan; Fuchs, Vladimír; Loarer, T.; Pánek, Radomír; Saint Laurent, F.; Stöckel, Jan; Adámek, Jiří; Bucalossi, J.; Dejarnac, Renaud; Devynck, P.; Hertout, P.; Hron, Martin; Nanobashvili, I.; Rimini, F.G.; Sarkissian, A.

2006-01-01

Roč. 812, - (2006), s. 27-34 ISSN 0094-243X. [AIP Conference Proceedings. Opole-Turawa, 06.09.2006-09.09.2006] R&D Projects: GA ČR GP202/03/P062 Institutional research plan: CEZ:AV0Z20430508 Keywords : tokamak * scrape-off layer * plasma flow * radial transport * Mach probe Subject RIV: BL - Plasma and Gas Discharge Physics http://proceedings.aip.org/dbt/dbt.jsp?KEY=APCPCS&Volume=812&Issue=1

Characterization of Scrape-Off layer turbulence changes induced by a non-axisymmetric magnetic perturbation in an ASDEX upgrade low density L-mode

International Nuclear Information System (INIS)

Mueller, H.W.; Carralero, D.; Birkenmeier, G.; Conway, G.D.; Fischer, R.; Happel, T.; Manz, P.; Suttrop, W.; Wolfrum, E.

2014-01-01

In the tokamak ASDEX Upgrade the influence of a non-axisymmetric n = 2 error field on the turbulence in the far scrape-off layer of a low density L-mode discharge has been studied. There is no density pump-out with the non-axisymmetric perturbation but an increase of the scrape-off layer density at the outer midplane. While the relative ion saturation current fluctuation level in the far scrape-off layer is decreasing, the skewness rises and especially the excess kurtosis grows by a factor of 1.5-3. The frequency of intermittent events (blobs) is increasing by 50 %. Also the poloidal velocity grows with the magnetic perturbation while the typical turbulent structure size becomes smaller by a factor 5-10 about 20-25 mm outside the separatrix. The local spectral density has been calculated from a two-point measurement of the ion saturation current. It is used to derive a dispersion relation. Two poloidal propagation velocities depending on the wave number have been found. One is an upper limit for the bulk E x B velocity and the second one the lower limit of the phase velocity. There is a significant contribution of the phase velocity to the propagation speed in the far scrape-off layer. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Structure of the classical scrape-off layer of a tokamak

Science.gov (United States)

Rozhansky, V.; Kaveeva, E.; Senichenkov, I.; Vekshina, E.

2018-03-01

The structure of the scrape-off layer (SOL) of a tokamak with little or no turbulent transport is analyzed. The analytical estimates of the density and electron temperature fall-off lengths of the SOL are put forward. It is demonstrated that the SOL width could be of the order of the ion poloidal gyroradius, as suggested in Goldston (2012 Nuclear Fusion 52 013009). The analytical results are supported by the results of the 2D simulations of the edge plasma with reduced transport coefficients performed by SOLPS-ITER transport code.

Characteristics of steady-state plasma flow in the tokamak limiter scrape-off layer

International Nuclear Information System (INIS)

Petrov, V.G.

1984-01-01

Steady state plasma flow in the scrape-off layer of a toroidal limiter is discussed. The force balance along the torus minor radius is taken into account, from which follows that the plasma pressure gradient is balanced by the ponderomotive force (1/c) j-vectorxB-vector, which arises in the presence of a current density component perpendicular to the magnetic field. The limiter has an important effect on the electric current flow in the scrape-off layer. It is shown that the electric potential and plasma density values differ from one side of the limiter to the other; this leads to plasma drift along the minor radius. The characteristic length of change in the plasma density is found to be of the order of the ion cyclotron radius calculated for a poloidal magnetic field. (author)

Transport of wall released impurities in the limiter scrape-off layer of a tokamak

International Nuclear Information System (INIS)

Claassen, H.A.; Repp, H.

1978-01-01

A collisional theory for the transport of heavy wall released impurities in the plasma scrape-off layer is developed, which to zero order approximation considers electron impact ionization and Coulomb collisions with the plasma ions. Impurity ion convection parallel to the magnetic field and radial drift motion are treated as first order correction terms. The theory, which under certain restrictions to the integral coefficients of the Fokker-Planck collision operator is independent of the special form of the plasma ion distribution, is applied to the calculation of the impurity ion fluxes in the scrape-off layer. Preliminary numerical results are presented for a model plasma ion distribution of the loss ellipse type and a half-maxwellian distribution of the wall released impurity atoms. (Auth.)

Blob sizes and velocities in the Alcator C-Mod scrape-off layer

DEFF Research Database (Denmark)

Kube, R.; Garcia, O.E.; LaBombard, B.

A new blob-tracking algorithm for the GPI diagnostic installed in the outboard-midplane of Alcator C-Mod is developed. I t tracks large-amplitude fluctuations propagating through the scrape-off layer and calculates blob sizes and velocities. We compare the results of this method to a blob velocity...

Influence of the Alfven wave spectrum on the scrape-off layer of the TCA tokamak

International Nuclear Information System (INIS)

Martin, Y.; Hollenstein, C.

1989-01-01

The study of the scrape-off layer (SOL) during Alfven wave heating may lead to a better understanding of the antenna-plasma interaction. The scrape-off layer of the TCA tokamak has been widely investigated by means of Langmuir probes. The aim of this work is to present measurements on the influence of the Alfven wave spectrum on the scrape-off layer. These experiments have shown that the plasma boundary layer is strongly affected by the wave field, in particular the ion saturation current and the floating potential. In TCA, as the spectrum evolves due to a density rise, the passage of the Alfven continua and their associated eigenmodes, the Discrete Alfven Wave (DAW) induces a strong depletion in the edge density of up to 70% during the continuum part and a density increase during the crossing of an eigenmode. The floating potential becomes negative during the continua and even more negative crossing the eigenmodes. In case of MHD mode activity, this behaviour changes for power exceeding 100 kW. The profiles of basic parameters are modified, depending on the wave spectrum. MHD mode activity which can occur during the RF (radio frequency) phase considerably alters the behaviour mentioned above. Finally, the modulation of the RF power allows us to characterize the coupling between RF power and typical edge parameters. (orig.)

Scrape-off layer tokamak plasma turbulence

Science.gov (United States)

Bisai, N.; Singh, R.; Kaw, P. K.

2012-05-01

Two-dimensional (2D) interchange turbulence in the scrape-off layer of tokamak plasmas and their subsequent contribution to anomalous plasma transport has been studied in recent years using electron continuity, current balance, and electron energy equations. In this paper, numerically it is demonstrated that the inclusion of ion energy equation in the simulation changes the nature of plasma turbulence. Finite ion temperature reduces floating potential by about 15% compared with the cold ion temperature approximation and also reduces the radial electric field. Rotation of plasma blobs at an angular velocity about 1.5×105 rad/s has been observed. It is found that blob rotation keeps plasma blob charge separation at an angular position with respect to the vertical direction that gives a generation of radial electric field. Plasma blobs with high electron temperature gradients can align the charge separation almost in the radial direction. Influence of high ion temperature and its gradient has been presented.

Discontinuous Galerkin methods for plasma physics in the scrape-off layer of tokamaks

International Nuclear Information System (INIS)

Michoski, C.; Meyerson, D.; Isaac, T.; Waelbroeck, F.

2014-01-01

A new parallel discontinuous Galerkin solver, called ArcOn, is developed to describe the intermittent turbulent transport of filamentary blobs in the scrape-off layer (SOL) of fusion plasma. The model is comprised of an elliptic subsystem coupled to two convection-dominated reaction–diffusion–convection equations. Upwinding is used for a class of numerical fluxes developed to accommodate cross product driven convection, and the elliptic solver uses SIPG, NIPG, IIPG, Brezzi, and Bassi–Rebay fluxes to formulate the stiffness matrix. A novel entropy sensor is developed for this system, designed for a space–time varying artificial diffusion/viscosity regularization algorithm. Some numerical experiments are performed to show convergence order on manufactured solutions, regularization of blob/streamer dynamics in the SOL given unstable parameterizations, long-time stability of modon (or dipole drift vortex) solutions arising in simulations of drift-wave turbulence, and finally the formation of edge mode turbulence in the scrape-off layer under turbulent saturation conditions

Characteristics of divertor plasma and scrape-off layer in JT-60U

International Nuclear Information System (INIS)

Itami, K.; Shimada, M.; Hosogane, N.

1992-01-01

Heat flux to the divertor is measured by thermography and the heat transport in the scrape-off layer is studied in beam heated discharges of JT-60U. The heat flux onto the divertor is ∝50% of total beam power at maximum. The in-out asymmetry of the heat flux P HEAT in /P HEAT out is as large as 20-40% when the ion grad-B drift is toward the divertor. Differences in P HEAT in /P HEA T out due to the direction of ion grad-B drift are as large as large as ∝40%. A scaling of the peaking factor Y of heat flux, defined by Y=2πRfq max /P HEAT , is obtained for beam heated discharges in JT-60U with a wide range of plasma parameters. The Y corresponds to the inverse of the thickness of the scrape-off layer. From a statistical analysis, it is found that the peaking factor Y of heat flux scales as P HEAT 0.49±0.18 anti n e -0.45±0.22 q eff -0.67±0.18 . (orig.)

Localized Scrape-Off Layer density modifications by Ion Cyclotron near fields in JET and ASDEX-Upgrade L-mode plasmas

Science.gov (United States)

Colas, L.; Jacquet, Ph.; Van Eester, D.; Bobkov, V.; Brix, M.; Meneses, L.; Tamain, P.; Marsen, S.; Silva, C.; Carralero, D.; Kočan, M.; Müller, H.-W.; Crombé, K.; Křivska, A.; Goniche, M.; Lerche, E.; Rimini, F. G.; JET-EFDA Contributors

2015-08-01

Combining Lithium beam emission spectroscopy and edge reflectometry, localized Scrape-Off Layer (SOL) density modifications by Ion Cyclotron Range of Frequencies (ICRF) near fields were characterized in JET L-mode plasmas. When using the ICRF wave launchers connected magnetically to the Li-beam chord, the density decreased more steeply 2-3 cm outside the last closed flux surface (mapped onto the outer mid-plane) and its value at the outer limiter radial position was half the ohmic value. The depletion depends on the ICRF power and on the phasing between adjacent radiating straps. Convection due to ponderomotive effects and/or E × B0 drifts is suspected: during ICRF-heated H-mode discharges in 2013, DC potentials up to 70 V were measured locally in the outer SOL by a floating reciprocating probe, located toroidally several metres from the active antennas. These observations are compared with probe measurements on ASDEX-Upgrade. Their implications for wave coupling, heat loads and impurity production are discussed.

Scrape-off layer width of parallel heat flux on tokamak COMPASS

Czech Academy of Sciences Publication Activity Database

Loureiro, J.; Silva, C.; Horáček, Jan; Adámek, Jiří; Stöckel, Jan

2014-01-01

Roč. 1, č. 3 (2014), s. 121 ISSN 2336-2626. [SPPT 2014 - 26th Symposium on Plasma Physics and Technology/26./. Prague, 16.06.2014-19.06.2014] R&D Projects: GA ČR(CZ) GAP205/12/2327 Institutional support: RVO:61389021 Keywords : tokamak * edge turbulent transport * Scrape-Off layer * Langmuir probe * Ball- pen probe Subject RIV: BL - Plasma and Gas Discharge Physics http://fyzika.feld.cvut.cz/misc/ppt/articles/2014/loureiro.pdf

2D scrape-off layer turbulence measurement using Deuterium beam emission spectroscopy on KSTAR

Science.gov (United States)

Lampert, M.; Zoletnik, S.; Bak, J. G.; Nam, Y. U.; Kstar Team

2018-04-01

Intermittent events in the scrape-off layer (SOL) of magnetically confined plasmas, often called blobs and holes, contribute significantly to the particle and heat loss across the magnetic field lines. In this article, the results of the scrape-off layer and edge turbulence measurements are presented with the two-dimensional Deuterium Beam Emission Spectroscopy system (DBES) at KSTAR (Korea Superconducting Tokamak Advanced Research). The properties of blobs and holes are determined in an L-mode and an H-mode shot with statistical tools and conditional averaging. These results show the capabilities and limitations of the SOL turbulence measurement of a 2D BES system. The results from the BES study were compared with the analysis of probe measurements. It was found that while probes offer a better signal-to-noise ratio and can measure blobs down to 3 mm size, BES can monitor the two-dimensional dynamics of larger events continuously during full discharges, and the measurement is not limited to the SOL on KSTAR.

Simulations of edge and scrape off layer turbulence in mega ampere spherical tokamak plasmas

DEFF Research Database (Denmark)

Militello, F; Fundamenski, W; Naulin, Volker

2012-01-01

The L-mode interchange turbulence in the edge and scrape-off-layer (SOL) of the tight aspect ratio tokamak MAST is investigated numerically. The dynamics of the boundary plasma are studied using the 2D drift-fluid code ESEL, which has previously shown good agreement with large aspect ratio machin...

Effects of ionizing scrape-off layers on local recycling in Tore Supra pump limiter experiments

International Nuclear Information System (INIS)

Chatelier, M.; Loarer, T.

1992-01-01

A series of ohmic discharges with active pumping in the Tore Supra outboard pump limiter has been analyzed with the DEGAS neutrals transport code and an analytic scrape-off layer (SOL) plasma model. Pumping speed and plenum pressure measurements indicated 5-10 torr.L/s throughput with only modest effects on density. A model is developed in which large exhaust fluxes, with little attendant effect on core plasma density, are explained in terms of SOL ionization of recycled and wall-desorbed neutrals. Particle balance with active pumping and constant line density requires that the wall return flux exceed the incident flux by approximately the pump throughput in the absence of external fueling. The radial profile of the H + source rate from ionization and dissociation of wall-desorbed molecules is seen to peak very near the radial position of the limiter throat. Consequently, a strong recycling vortex is created in the region of the limiter, with the ion flux amplified by factors of 2 at the outer limiter surfaces and > 3 within the limiter throat. The calculations indicate that less than 30% of the pump throughput is due to first-generation ions from the core efflux, with the balance from local recycling in the strongly ionizing SOL

Local gas injection as a scrape-off layer diagnostic on the Alcator C-Mod tokamak

International Nuclear Information System (INIS)

Jablonski, D.F.

1996-05-01

A capillary puffing array has been installed on Alcator C-Mod which allows localized introduction of gaseous species in the scrape-off layer. This system has been utilized in experiments to elucidate both global and local properties of edge transport. Deuterium fueling and recycling impurity screening are observed to be characterized by non-dimensional screening efficiencies which are independent of the location of introduction. In contrast, the behavior of non-recycling impurities is seen to be characterized by a screening time which is dependent on puff location. The work of this thesis has focused on the use of the capillary array with a camera system which can view impurity line emission plumes formed in the region of an injection location. The ionic plumes observed extend along the magnetic field line with a comet-like asymmetry, indicative of background plasma ion flow. The flow is observed to be towards the nearest strike-point, independent of x-point location, magnetic field direction, and other plasma parameters. While the axes of the plumes are generally along the field line, deviations are seen which indicate cross-field ion drifts. A quasi-two dimensional fluid model has been constructed to use the plume shapes of the first charge state impurity ions to extract information about the local background plasma, specifically the temperature, parallel flow velocity, and radial electric field. Through comparisons of model results with those of a three dimensional Monte Carlo code, and comparisons of plume extracted parameters with scanning probe measurements, the efficacy of the model is demonstrated. Plume analysis not only leads to understandings of local edge impurity transport, but also presents a novel diagnostic technique

Local gas injection as a scrape-off layer diagnostic on the Alcator C-Mod tokamak

Energy Technology Data Exchange (ETDEWEB)

Jablonski, David F. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

1996-05-01

A capillary puffing array has been installed on Alcator C-Mod which allows localized introduction of gaseous species in the scrape-off layer. This system has been utilized in experiments to elucidate both global and local properties of edge transport. Deuterium fueling and recycling impurity screening are observed to be characterized by non-dimensional screening efficiencies which are independent of the location of introduction. In contrast, the behavior of non-recycling impurities is seen to be characterized by a screening time which is dependent on puff location. The work of this thesis has focused on the use of the capillary array with a camera system which can view impurity line emission plumes formed in the region of an injection location. The ionic plumes observed extend along the magnetic field line with a comet-like asymmetry, indicative of background plasma ion flow. The flow is observed to be towards the nearest strike-point, independent of x-point location, magnetic field direction, and other plasma parameters. While the axes of the plumes are generally along the field line, deviations are seen which indicate cross-field ion drifts. A quasi-two dimensional fluid model has been constructed to use the plume shapes of the first charge state impurity ions to extract information about the local background plasma, specifically the temperature, parallel flow velocity, and radial electric field. Through comparisons of model results with those of a three dimensional Monte Carlo code, and comparisons of plume extracted parameters with scanning probe measurements, the efficacy of the model is demonstrated. Plume analysis not only leads to understandings of local edge impurity transport, but also presents a novel diagnostic technique.

Probe measurements for impurity transport in the scrape-off layer of JIPP T-II

International Nuclear Information System (INIS)

Mohri, M.; Satake, T.; Hashiba, H.; Yamashina, T.; Amemiya, S.

1982-05-01

Impurity transport processes in the scrape-off layer of the JIPP T-II device have been studied by a probe method. A cubical silicon probe was inserted and exposed to 20 identical tokamak discharges in the scrape-off region. Deposited impurities were analyzed with use of AES, RBS and PIXE equipments. The main metallic impurities were molybdenum and iron whose deposition behavior was almost the same on any side of the probe, and their fluxes were observed to be 1.2 x 10 13 /cm 2 .discharge on the electron drift side and 5.2 x 10 13 /cm 2 .discharge on the ion drift side, respectively at the distance of 18.3 cm from the center line of the plasma. The mean transport energy of the impurities striking the probe surface was estimated from the depth concentration profile applying the LSS theory for iron as 90 eV on the electron drift side and 250 eV on the ion drift side, respectively. The e-folding length of the scrape-off plasma density was measured by the radial distribution of a deposited tantalum amount to be 0.64 cm on the electron drift side and 1.73 cm on the ion drift side, respectively. (author)

Intermittent fluctuations in the Alcator C-Mod scrape-off layer for ohmic and high confinement mode plasmas

Science.gov (United States)

Garcia, O. E.; Kube, R.; Theodorsen, A.; LaBombard, B.; Terry, J. L.

2018-05-01

Plasma fluctuations in the scrape-off layer of the Alcator C-Mod tokamak in ohmic and high confinement modes have been analyzed using gas puff imaging data. In all cases investigated, the time series of emission from a single spatially resolved view into the gas puff are dominated by large-amplitude bursts, attributed to blob-like filament structures moving radially outwards and poloidally. There is a remarkable similarity of the fluctuation statistics in ohmic plasmas and in edge localized mode-free and enhanced D-alpha high confinement mode plasmas. Conditionally averaged waveforms have a two-sided exponential shape with comparable temporal scales and asymmetry, while the burst amplitudes and the waiting times between them are exponentially distributed. The probability density functions and the frequency power spectral densities are similar for all these confinement modes. These results provide strong evidence in support of a stochastic model describing the plasma fluctuations in the scrape-off layer as a super-position of uncorrelated exponential pulses. Predictions of this model are in excellent agreement with experimental measurements in both ohmic and high confinement mode plasmas. The stochastic model thus provides a valuable tool for predicting fluctuation-induced plasma-wall interactions in magnetically confined fusion plasmas.

Vlasov modelling of parallel transport in a tokamak scrape-off layer

International Nuclear Information System (INIS)

Manfredi, G; Hirstoaga, S; Devaux, S

2011-01-01

A one-dimensional Vlasov-Poisson model is used to describe the parallel transport in a tokamak scrape-off layer. Thanks to a recently developed 'asymptotic-preserving' numerical scheme, it is possible to lift numerical constraints on the time step and grid spacing, which are no longer limited by, respectively, the electron plasma period and Debye length. The Vlasov approach provides a good velocity-space resolution even in regions of low density. The model is applied to the study of parallel transport during edge-localized modes, with particular emphasis on the particles and energy fluxes on the divertor plates. The numerical results are compared with analytical estimates based on a free-streaming model, with good general agreement. An interesting feature is the observation of an early electron energy flux, due to suprathermal electrons escaping the ions' attraction. In contrast, the long-time evolution is essentially quasi-neutral and dominated by the ion dynamics.

Vlasov modelling of parallel transport in a tokamak scrape-off layer

Energy Technology Data Exchange (ETDEWEB)

Manfredi, G [Institut de Physique et Chimie des Materiaux, CNRS and Universite de Strasbourg, BP 43, F-67034 Strasbourg (France); Hirstoaga, S [INRIA Nancy Grand-Est and Institut de Recherche en Mathematiques Avancees, 7 rue Rene Descartes, F-67084 Strasbourg (France); Devaux, S, E-mail: Giovanni.Manfredi@ipcms.u-strasbg.f, E-mail: hirstoaga@math.unistra.f, E-mail: Stephane.Devaux@ccfe.ac.u [JET-EFDA, Culham Science Centre, Abingdon, OX14 3DB (United Kingdom)

2011-01-15

A one-dimensional Vlasov-Poisson model is used to describe the parallel transport in a tokamak scrape-off layer. Thanks to a recently developed 'asymptotic-preserving' numerical scheme, it is possible to lift numerical constraints on the time step and grid spacing, which are no longer limited by, respectively, the electron plasma period and Debye length. The Vlasov approach provides a good velocity-space resolution even in regions of low density. The model is applied to the study of parallel transport during edge-localized modes, with particular emphasis on the particles and energy fluxes on the divertor plates. The numerical results are compared with analytical estimates based on a free-streaming model, with good general agreement. An interesting feature is the observation of an early electron energy flux, due to suprathermal electrons escaping the ions' attraction. In contrast, the long-time evolution is essentially quasi-neutral and dominated by the ion dynamics.

Numerical scalings of the decay lengths in the scrape-off layer

DEFF Research Database (Denmark)

Militello, F.; Naulin, V; Nielsen, Anders Henry

2013-01-01

Numerical simulations of L-mode turbulence in the scrape-off layer (SOL) are used to construct power scaling laws for the characteristic decay lengths of the temperature, density and heat flux at the outer mid-plane. Most of the results obtained are in qualitative agreement with the experimental...... observations despite the known limitation of the model. Quantitative agreement is also obtained for some exponents. In particular, an almost linear inverse dependence of the heat flux decay length with the plasma current is recovered. The relative simplicity of the theoretical model used allows one to gain...

Scrape-off layer turbulence in TCV: evidence in support of stochastic modelling

Czech Academy of Sciences Publication Activity Database

Theodorsen, A.; Garcia, O.E.; Horáček, Jan; Kube, R.; Pitts, R.A.

2016-01-01

Roč. 58, č. 4 (2016), č. článku 044006. ISSN 0741-3335 R&D Projects: GA ČR(CZ) GAP205/12/2327 Institutional support: RVO:61389021 Keywords : turbulence * intermittency * transport * scrape-off layer * tcv * plasma * tokamak Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 2.392, year: 2016 http://iopscience.iop.org/article/10.1088/0741-3335/58/4/044006/meta

Control of long range turbulent transport with biasing in the tokamak scrape-off-layer

International Nuclear Information System (INIS)

Figarella, C.F.; Ghendrih, Ph.; Sarazin, Y.; Attuel, G.; Falchetto, G.; Fleurence, E.; Garbet, X.; Grandgirard, V.

2004-01-01

Cross field transport in the SOL (scrape-off-layer) influences tokamak performance in particular regarding the divertor efficiency. Recent experiment evidence emphasizes non-exponential and/or flat SOL profiles that suggest a large perpendicular transport. A 2-dimensional fluid model based on the interchange instability to simulate the SOL turbulence was found to exhibits intermittent dynamics of the particle flux. We propose a control method that prevents long range transport events from reaching the far SOL: It consists in biasing the far SOL leading to a transport barrier which stops the propagation of these intermittent events. The best trade off is to localize the biased toroidal ring around the baffles. We show that such a control is achievable providing the strength of the barrier is strong enough. The investigation of the minimal biasing power required to achieve the control as well as its experimental estimate is performed. (authors)

Experimental and theoretical investigation of density and potential fluctuations in the scrape-off layer of ASDEX

Energy Technology Data Exchange (ETDEWEB)

Endler, M; Giannone, L.; Niedermeyer, H; Rudyj, A; Theimer, G [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany)

1994-12-31

Electrostatic fluctuations (i.e. the magnetic field is assumed constant) are candidates for the explanation of the anomalous transport of particles and energy in both tokamaks and stellarators. While most theoretical effort has been directed to an explanation of the anomalous transport in the bulk plasma, it is now widely being realized that the anomalous radial transport in the scrape-off layer, determining the width of the power flow channel at limiter or divertor plates, may be equally important to a future reactor experiment. In the divertor tokamak ASDEX density and potential fluctuations in the scrape-off layer were investigated with high temporal and spatial resolution by Langmuir probes and an H{sub {alpha}} diagnostic. Many results of these measurements were reported and are summarized below. Several of these properties of the fluctuations have also been reported from other experiments. (author) 3 refs., 4 figs.

Poloidal asymmetries in the scrape-off layer plasma of the Alcator C tokamak

International Nuclear Information System (INIS)

LaBombard, B.; Lipschultz, B.

1987-01-01

Large poloidal asymmetries in density, electron temperature, radial density e-folding length and floating potential have been measured in the plasma existing between the limiter radius and the wall of the Alcator C tokamak. Typically, variations in density by factors of about 4-20 and variations in radial density e-folding length by factors of about 3-8 are recorded in discharges which are bounded by poloidally symmetric ring limiters. These poloidal asymmetries show that pressure is a function of poloidal angle on open magnetic flux surfaces in this region of the plasma. Observations of toroidally symmetric MARFE (multifaceted asymmetric radiation from the edge) phenomena further imply that density and perhaps pressure are also a function of poloidal angle on closed flux surfaces existing just inside the limiter radius. The magnitude of these poloidal asymmetries and their dependence on poloidal angle persists independent of machine parameters (central plasma density, plasma current, toroidal field, MARFE versus non-MARFE discharges). Analysis of the data indicates that these asymmetries are caused by poloidal variations in perpendicular particle and heat transport in both the main plasma and the scrape-off layer. A number of possible asymmetric perpendicular transport processes in the scrape-off layer plasma are examined, including diffusion and E-vectorxB-vector plasma convection. (author)

Scrape-off layer profile modifications by convective cells

International Nuclear Information System (INIS)

Myra, J.R.; DIppolito, D.A.

1996-01-01

Convective cells (CC close-quote s) are important in understanding density profile modifications induced by ion cyclotron range of frequencies (ICRF) antennas. This has motivated the present work in which the effect of CC close-quote s on transport in the scrape-off layer is studied, in the regime where the density gradient scale length L n and the cell size L are comparable. Monte Carlo simulations show that closed cell convection acts to flatten the density profile, and that open cells enhance the particle flow to the wall, depleting the density and yielding profiles similar to those measured near ICRF antennas. A new one-dimensional, two-branch model of CC transport is shown to agree well with the simulations. The model gives rise to two characteristic scale lengths, only one of which is retained in the enhanced diffusion models that are applicable for L n >L. The two-branch model is expected to be useful in analyzing ICRF experiments. copyright 1996 American Institute of Physics

Coherence imaging of scrape-off-layer and divertor impurity flows in the Mega Amp Spherical Tokamak (invited)

Energy Technology Data Exchange (ETDEWEB)

Silburn, S. A., E-mail: s.a.silburn@durham.ac.uk; Sharples, R. M. [Centre for Advanced Instrumentation, Department of Physics, Durham University, Durham DH1 3LE (United Kingdom); Harrison, J. R.; Meyer, H.; Michael, C. A. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Howard, J. [Plasma Research Laboratory, Australian National University, Canberra, ACT 0200 (Australia); Gibson, K. J. [York Plasma Institute, Department of Physics, University of York, Heslington, York YO10 5DD (United Kingdom)

2014-11-15

A new coherence imaging Doppler spectroscopy diagnostic has been deployed on the UK’s Mega Amp Spherical Tokamak for scrape-off-layer and divertor impurity flow measurements. The system has successfully obtained 2D images of C III, C II, and He II line-of-sight flows, in both the lower divertor and main scrape-off-layer. Flow imaging has been obtained at frame rates up to 1 kHz, with flow resolution of around 1 km/s and spatial resolution better than 1 cm, over a 40° field of view. C III data have been tomographically inverted to obtain poloidal profiles of the parallel impurity flow in the divertor under various conditions. In this paper we present the details of the instrument design, operation, calibration, and data analysis as well as a selection of flow imaging results which demonstrate the diagnostic's capabilities.

Turbulent regimes in the tokamak scrape-off layer

International Nuclear Information System (INIS)

Mosetto, A.

2014-01-01

The tokamak scrape-off layer (SOL) is the plasma region characterized by open field lines that start and end on the vessel walls. The plasma dynamics in the SOL plays a crucial role in determining the overall performance of a tokamak, since it controls the plasma-wall interactions, being responsible of exhausting the tokamak power, it regulates the overall plasma confinement, and it governs the plasma refueling and the removal of fusion ashes. Scrape-off layer physics is intrinsically non-linear and characterized by phenomena that occur on a wide range of spatio-temporal scales. Free energy sources drive a number of unstable modes that develop into turbulence and lead to transport of particles and heat across the magnetic field lines. Depending on the driving instability, different SOL turbulent regimes can be identified. As the SOL turbulent regimes determine the plasma confinement properties and the SOL width (and, consequently, the power flux on the vessel wall, for example), it is of crucial importance to understand which turbulent regimes are active in the SOL, under which conditions they develop, and which are the main properties of the associated turbulent transport. In the present thesis we define the SOL turbulent regimes, and we provide a framework to identify them, given the operational SOL parameters. Our study is based on the drift-reduced Braginskii equations and it is focused on a limited tokamak SOL configuration. We first describe the main SOL linear instabilities, such as the inertial and resistive branches of the drift waves, the resistive, inertial and ideal branches of the ballooning modes, and the ion temperature gradient mode. Then, we find the SOL turbulent regimes depending on the instability driving turbulent transport, assuming that turbulence saturates when the radial gradient associated to the pressure fluctuations is comparable to the equilibrium one. Our methodology for the turbulent regime identification is supported by the analysis

Gyrokinetic particle simulation of neoclassical transport in the pedestal/scrape-off region of a tokamak plasma

Energy Technology Data Exchange (ETDEWEB)

Ku, S [Courant Institute of Mathematical Sciences, New York University (United States); Chang, C-S [Courant Institute of Mathematical Sciences, New York University (United States); Adams, M [Columbia University (United States); Cummings, J [California Institute of Technology (United States); Hinton, F [Hinton Associates (United States); Keyes, D [Columbia University (United States); Klasky, S [Oak Ridge National Laboratory (United States); Lee, W [Princeton Plasma Physics Laboratory (United States); Lin, Z [University of California at Irvine (United States); Parker, S [University of Colorado at Boulder (United States)

2006-09-15

A gyrokinetic neoclassical solution for a diverted tokamak edge plasma has been obtained for the first time using the massively parallel Jaguar XT3 computer at Oak Ridge National Laboratory. The solutions show similar characteristics to the experimental observations: electric potential is positive in the scrape-off layer and negative in the H-mode layer, and the parallel rotation is positive in the scrape-off layer and at the inside boundary of the H-mode layer. However, the solution also makes a new physical discovery that there is a strong ExB convective flow in the scrape-off plasma. A general introduction to the edge simulation problem is also presented.

One-dimensional fluid model for transport in divertor and limiter tokamak scrape-off layers

International Nuclear Information System (INIS)

Lipschultz, B.

1983-11-01

Single-fluid transport in the plasma scrape-off layer is modeled for poloidal divertor and mechanically limited discharges. This numerical model is one-dimensional along a field line and time-independent. Conductive and convective transport, as well as impurity and neutral source (sink) terms are included. A simple shooting method technique is used for obtaining solutions. Results are shown for the case of the proposed Alcator DCT tokamak

Simulation of the scrape-off layer plasma during a disruption

International Nuclear Information System (INIS)

Rognlien, T.D.; Crotinger, J.A.; Porter, G.D.; Smith, G.R.; Kellman, A.G.; Taylor, P.L.

1996-01-01

The evolution of the scrape-off layer (SOL) during a disruption in the DIII-D tokamak is modeled using the 2-D UEDGE transport code. The focus is on the thermal quench phase when most of the energy content of the discharge is rapidly transported across the magnetic separatrix where it then flows to material surfaces or is radiated. Comparisons between the simulation and an experiment on the DIII-D tokamak are made with the heat flux to the divertor plate, and temperature and density profiles at the SOL midplane. The temporal response of the separate electron and ion heat-flux components to the divertor plate is calculated. The sensitivity of the solution to assumptions of electron heat-flux models and impurity radiation is investigated

Plasma transport in the Scrape-off-Layer of magnetically confined plasma and the plasma exhaust

DEFF Research Database (Denmark)

Rasmussen, Jens Juul; Naulin, Volker; Nielsen, Anders Henry

An overview of the plasma dynamics in the Scrape-off-Layer (SOL) of magnetically confined plasma is presented. The SOL is the exhaust channel of the warm plasma from the core, and the understanding of the SOL plasma dynamics is one of the key issues in contemporary fusion research. It is essential...... for operation of fusion experiments and ultimately fusion power plants. Recent results clearly demonstrate that the plasma transport through the SOL is dominated by turbulent intermittent fluctuations organized into filamentary structures convecting particles, energy, and momentum through the SOL region. Thus......, the transport cannot be described and parametrized by simple diffusive type models. The transport leads to strong localized power loads on the first wall and the plasma facing components, which have serious lasting influence....

Fast reciprocating probe system for local scrape-off layer measurements in front of the lower hybrid launcher on JT-60U

International Nuclear Information System (INIS)

Asakura, N.; Tsuji-Iio, S.; Ikeda, Y.; Neyatani, Y.; Seki, M.

1995-01-01

A fast reciprocating probe system with a long drive shaft was incorporated into a multi-junction lower hybrid (LH) wave launcher on JT-60U in order to investigate an improved coupling mechanism of the radio frequency wave to the core plasma. The system has been operated reliably over a horizontal scan of 25 cm in 1.5 s using a compact pneumatic cylinder drive and springs. A double probe measurement provided the scrape-off layer plasma profile between the last closed flux surface and the first wall with the spatial resolution of 1-2 mm measured with a laser displacement gauge. The profiles of the electron density n e and temperature T e were in good agreement with those obtained with a triple probe method. During the LH wave injection with good coupling to the core plasma, an increase in the local T e was observed in front of the LH launcher mouth. The local n e was (7-10)x10 16 m -3 , consistent values needed for the good coupling. copyright 1995 American Institute of Physics

Scrape-off layer reflectometer for Alcator C-Moda)

Science.gov (United States)

Lau, Cornwall; Hanson, Greg; Wilgen, John; Lin, Yijun; Wukitch, Steve

2010-10-01

A swept-frequency X-mode reflectometer is being built for Alcator C-Mod to measure the scrape-off layer density profiles at the top, middle, and bottom locations in front of both the new lower hybrid launcher and the new ion cyclotron range of frequencies antenna. The system is planned to operate between 100 and 146 GHz at sweep rates from 10 μs to 1 ms, and will cover a density range of approximately 1016-1020 m-3 at B0=5-5.4 T. To minimize the effects of density fluctuations, both differential phase and full phase reflectometry will be employed. Design, test data, and calibration results of this electronics system will be discussed. To reduce attenuation losses, tallguide (TE01) will be used for most of the transmission line system. Simulations of high mode conversion in tallguide components, such as e-plane hyperbolic secant radius of curvature bends, tapers, and horn antennas will be shown. Experimental measurements of the total attenuation losses of these components in the lower hybrid waveguide run will also be presented.

Experimental and theoretical investigation of density and potential fluctuations in the scrape-off layer of ASDEX

International Nuclear Information System (INIS)

Endler, M.; Giannone, L.; Niedermeyer, H.; Rudyj, A.; Theimer, G.

1993-01-01

In the divertor tokamak ASDEX density and potential fluctuations in the scrape-off layer were investigated with high temporal and spatial resolution by Langmuir probes and an H α diagnostic. Many results of these measurements were reported and are summarized below. Several of these properties of the fluctuations have also been reported from other experiments. (orig.)

Poloidal Asymmetry in the Narrow Heat Flux Feature in the TCV Scrape-Off Layer.

Czech Academy of Sciences Publication Activity Database

Tsui, C.K.; Boedo, J. A.; Halpern, F.D.; Loizu, J.; Nespoli, F.; Horáček, Jan; Labit, B.; Morales, J.; Reimerdes, H.; Ricci, P.; Theiler, C.; Coda, S.; Duval, B. P.; Furno, I.

2017-01-01

Roč. 24, č. 6 (2017), č. článku 062508. ISSN 1070-664X R&D Projects: GA ČR(CZ) GA15-10723S EU Projects: European Commission(XE) 633053 - EUROfusion Institutional support: RVO:61389021 Keywords : Scrape-Off Layer * TCV * tokamak * plasma Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 2.115, year: 2016 http://dx.doi.org/10.1063/1.4985075

Model of divertor biasing and control of scrape-off layer and divertor plasmas

International Nuclear Information System (INIS)

Nagasaki, K.; Itoh, K.; Itoh, S.

1991-02-01

Analytic model of the divertor biasing is described. For the given plasma and energy sources from the core plasma, the heat and particle flux densities on the divertor plate as well as scrape-off-layer (SOL)/divertor plasmas are analyzed in a slab model. Using a two-dimensional model, the effects of the divertor biasing and SOL current are studied. The conditions to balance the plasma temperature or sheath potential on different divertor plates are obtained. Effect of the SOL current on the heat channel width is also discussed. (author)

Diagnostics of mobile dust in scrape-off layer plasmas

International Nuclear Information System (INIS)

Ratynskaia, S; Castaldo, C; Bergsaaker, H; Rudakov, D

2011-01-01

Dust production and accumulation pose serious safety and operational implications for the next generation fusion devices. Mobile dust particles can result in core plasma contamination with impurities, and those with high velocities can significantly contribute to the wall erosion. Diagnostics for monitoring dust in tokamaks during plasma discharges are hence important as they can provide information on dust velocity and size, and-in some cases-on dust composition. Such measurements are also valuable as an input for theoretical models of dust dynamics in scrape-off layer plasmas. Existing in situ dust diagnostics, focusing on the range of dust parameters they can detect, are reviewed. Particular attention is paid to the diagnostics which allow us to detect tails of the dust velocity and size distributions, e.g. small and very fast particles. Some of the techniques discussed have been adopted from space-related research and have been shown to be feasible and useful for tokamak applications as well.

Limiter effects on scrape-off layer fluctuations and transport

International Nuclear Information System (INIS)

Thayer, D.R.; Diamond, P.H.; Wootton, A.J.

1987-01-01

Edge turbulence experiments indicate that radial particle flux increases as a function of radius up to the scrape-off layer (SOL), and that the Boltzman relation is violated. Resistivity gradient driven turbulence (RGDT) theory has been shown to track the radial dependence of the particle flux in the plasma edge closer than dissipative density gradient driven turbulence (DDGDT) theory. Also, the Boltzman relation is not invoked for RGDT while it is usually assumed for DDGDT. Consequently, RGDT is a more likely candidate for an edge turbulence model. However, Langmuir probe experiments indicate that the particle flux is reduced by as much as 50% in the SOL. Thus, since basic turbulence theories do not account for limiter effects, the primary focus of this study is to include such effects in a RGDT theory of the SOL. We present an analysis of SOL fluctuations using a rippling mode or RGDT calculation which incorporates the essential limiter boundary condition.(orig./GG)

The GBS code for tokamak scrape-off layer simulations

International Nuclear Information System (INIS)

Halpern, F.D.; Ricci, P.; Jolliet, S.; Loizu, J.; Morales, J.; Mosetto, A.; Musil, F.; Riva, F.; Tran, T.M.; Wersal, C.

2016-01-01

We describe a new version of GBS, a 3D global, flux-driven plasma turbulence code to simulate the turbulent dynamics in the tokamak scrape-off layer (SOL), superseding the code presented by Ricci et al. (2012) [14]. The present work is driven by the objective of studying SOL turbulent dynamics in medium size tokamaks and beyond with a high-fidelity physics model. We emphasize an intertwining framework of improved physics models and the computational improvements that allow them. The model extensions include neutral atom physics, finite ion temperature, the addition of a closed field line region, and a non-Boussinesq treatment of the polarization drift. GBS has been completely refactored with the introduction of a 3-D Cartesian communicator and a scalable parallel multigrid solver. We report dramatically enhanced parallel scalability, with the possibility of treating electromagnetic fluctuations very efficiently. The method of manufactured solutions as a verification process has been carried out for this new code version, demonstrating the correct implementation of the physical model.

The propagation of Blobs in the scrape-off layer of tokamak

International Nuclear Information System (INIS)

Xu Jianqiang; Peng Xiaodong

2013-01-01

The propagation of special coherent structures (blobs) in the tokamak scrape-off layer (SOL) is studied numerically. Considering that the hypothesis which assumes that electrostatic potential Ø<<1 in existing model is not self-consistent with numerical results, thus modification is done to blob dynamics. Results show that the symmetry of the blob in the poloidal direction is broken and the reason for the symmetry break is discussed briefly. The blob velocity increases with its initial relative amplitude, while decreases with the rising of plasma sheath dissipation near the divertor plate. It should be emphasized that a new type of coherent structures with density lower than the bulk plasmas referred to as holes appears in the presence of strong sheath dissipation. (authors)

Stochastic modelling of intermittent fluctuations in the scrape-off layer: Correlations, distributions, level crossings, and moment estimation

Energy Technology Data Exchange (ETDEWEB)

Garcia, O. E., E-mail: odd.erik.garcia@uit.no; Kube, R.; Theodorsen, A. [Department of Physics and Technology, UiT The Arctic University of Norway, N-9037 Tromsø (Norway); Pécseli, H. L. [Physics Department, University of Oslo, PO Box 1048 Blindern, N-0316 Oslo (Norway)

2016-05-15

A stochastic model is presented for intermittent fluctuations in the scrape-off layer of magnetically confined plasmas. The fluctuations in the plasma density are modeled by a super-position of uncorrelated pulses with fixed shape and duration, describing radial motion of blob-like structures. In the case of an exponential pulse shape and exponentially distributed pulse amplitudes, predictions are given for the lowest order moments, probability density function, auto-correlation function, level crossings, and average times for periods spent above and below a given threshold level. Also, the mean squared errors on estimators of sample mean and variance for realizations of the process by finite time series are obtained. These results are discussed in the context of single-point measurements of fluctuations in the scrape-off layer, broad density profiles, and implications for plasma–wall interactions due to the transient transport events in fusion grade plasmas. The results may also have wide applications for modelling fluctuations in other magnetized plasmas such as basic laboratory experiments and ionospheric irregularities.

Radial transport in the far scrape-off layer of ASDEX upgrade during L-mode and ELMy H-mode

DEFF Research Database (Denmark)

Ionita, C.; Naulin, Volker; Mehlmann, F.

2013-01-01

The radial turbulent particle flux and the Reynolds stress in the scrape-off layer (SOL) of ASDEX Upgrade were investigated for two limited L-mode (low confinement) and one ELMy H-mode (high confinement) discharge. A fast reciprocating probe was used with a probe head containing five Langmuir...

Understanding and suppressing the near Scrape-Off Layer in inboard-limited plasmas in TCV.

Czech Academy of Sciences Publication Activity Database

Nespoli, F.; Labit, B.; Furno, I.; Horáček, Jan; Tsui, C.K.; Boedo, J. A.; Maurizio, R.; Reimerdes, H.; Theiler, C.; Ricci, P.; Halpern, F.D.; Sheikh, U.; Verhaegh, K.; Pitts, R.A.; Militello, F.

2017-01-01

Roč. 57, č. 12 (2017), č. článku 126029. ISSN 0029-5515 R&D Projects: GA ČR(CZ) GA15-10723S EU Projects: European Commission(XE) 633053 - EUROfusion Institutional support: RVO:61389021 Keywords : tokamak * TCV * scrape-off layer * heat flux * limiter * infrared thermography * Langmuir probes Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 3.307, year: 2016 http://iopscience.iop.org/article/10.1088/1741-4326/aa84e0

Influence of the Alfven wave spectrum on the scrape-off layer of the TCA tokamak

International Nuclear Information System (INIS)

Martin, Y.; Hollenstein, Ch.

1988-01-01

The study of the Scrape-Off Layer (SOL) during Alfven wave heating may lead to a better understanding of the antenna-plasma interaction. The SOL of the TCA tokamak has been widely investigated by means of Langmuir probes. The aim of the present work is to present in detail the influence of the Alfven wave spectrum on the SOL. The experiments have shown that the plasma boundary layer is strongly affected by the RF, in particular the ion density, the electron temperature and the floating potential. In TCA, as the spectrum evolves due to a density rise, the passage of the Alfven continua and their associated eigenmodes (DAW) induces a strong depletion in the edge density of up to 70% during the continuum part and a density increase during the crossing of an eigenmode. The floating potential becomes negative during the continua and even more negative crossing the eigenmodes. This behaviour changes as a function of the power transmitted to the plasma through the antennae, especially we have found with MHD modes a change around 100 kW. The profiles of the basic parameters are modified, depending on the wave spectrum. MHD mode activity which can occur during the RF phase considerably alters the behaviour mentioned above. Finally, the modulation of the RF power allows us to characterize the difference in coupling, for the continua and the eigenmodes, between the Alfven wave field and the scrape-off layer. (author) 5 figs., 6 refs

Electromagnetic ELM and inter-ELM filaments detected in the COMPASS Scrape-Off Layer.

Czech Academy of Sciences Publication Activity Database

Spolaore, M.; Kovařík, Karel; Stöckel, Jan; Adámek, Jiří; Dejarnac, Renaud; Ďuran, Ivan; Komm, Michael; Markovič, Tomáš; Martines, E.; Pánek, Radomír; Seidl, Jakub; Vianello, N.

2017-01-01

Roč. 12, August (2017), s. 844-851 ISSN 2352-1791. [PSI 2016 - 22nd International Conference on Plasma Surface Interactions in Controlled Fusion Devices/22./. Roma, 30.05.2016-03.06.2016] R&D Projects: GA MŠk(CZ) 8D15001; GA MŠk(CZ) LM2015045 EU Projects: European Commission(XE) 633053 - EUROfusion Institutional support: RVO:61389021 Keywords : Electromagnetic filaments * ELMs * Scrape-Off Layer * Magnetic fluctuations * Current density Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) http://www.sciencedirect.com/science/article/pii/S2352179116301934

Theory of the scrape-off layer width in inner-wall limited tokamak plasmas

International Nuclear Information System (INIS)

Halpern, F.D.; Ricci, P.; Jolliet, S.; Loizu, J.; Mosetto, A.

2014-01-01

We develop a predictive theory applicable to the scrape-off layer (SOL) of inner-wall limited plasmas. Using the non-linear flattening of the pressure profile as a saturation mechanism for resistive ballooning modes, we are able to demonstrate and quantify the increase of the SOL width with plasma size, connection length, plasma β, and collisionality. Individual aspects of the theory, such as saturation physics, parallel dynamics, and system size scaling, are tested and verified using non-linear, 3D flux-driven SOL turbulence simulations. Altogether, very good agreement between theory and simulation is found. (paper)

Cross-field blob transport in tokamak scrape-off-layer plasmas

International Nuclear Information System (INIS)

D'Ippolito, D.A.; Myra, J.R.; Krasheninnikov, S.I.

2002-01-01

Recent measurements show that nondiffusive, intermittent transport of particles can play a major role in the scrape-off-layer (SOL) of fusion experiments. A possible mechanism for fast convective plasma transport is related to the plasma filaments or 'blobs' observed in the SOL with fast cameras and probes. In this paper, physical arguments suggesting the importance of blob transport [S. I. Krasheninnikov, Phys. Lett. A 283, 368 (2001)] have been extended by calculations using a three-field fluid model, treating the blobs as coherent propagating structures. The properties of density, temperature and vorticity blobs, and methods of averaging over ensembles of blobs to get the average SOL profiles, are illustrated. The role of ionization of background neutrals in sustaining the density blob transport is also discussed. Many qualitative features of the experiments, such as relatively flat density profiles and transport coefficients increasing toward the wall, are shown to emerge naturally from the blob transport paradigm

Parametric study of biased scrape-off layer

International Nuclear Information System (INIS)

Parbhakar, K.

1992-01-01

The particle and energy balance equations in the scrape-off layer (SOL) plasma are solved analytically in a rectangular domain. The parallel flow is supposed to be convective, whereas the cross field flow is assumed diffusive, with modifications due to a radial E field. When the energy balance equation is neglected we get a quadratic equation for Λ, the e-folding density scale length. The normalized e-folding scale length Λ/Λ 0 (Λ 0 = Λ for E = 0) is a function of single parameter α (= eEλ 0 /2kT, where T is the plasma temperature, e the elementary charge and k is Boltzmann's constant), and monotonically increases with α. Taking the energy balance equation into account and neglecting R i (the ionization rate), the quadratic equation is further simplified, and Λ/Λ 0 again depends on a single parameter, determined by Q (the input power flux), D (the cross field diffusion coefficient), Λ (the sheath transmission coefficient for energy) and n p (the plate density). Now Λ/Λ 0 decreases with Q and increases linearly with D, γ and n p . The variation of Λ/Λ 0 with E is estimated for TdeV and ITER. We find that, by a proper choice of parameters, biasing may be a very valuable tool to modify the SOL properties at modest E fields, provided the heat load on the divertor plate is not excessively large

Theoretical analysis of long range turbulent transport in the scrape-off-layer

International Nuclear Information System (INIS)

Ghendrih, Ph.; Sarazin, Y.; Attuel, G.; Clement, C.; Falchetto, G.; Garbet, X.; Grandgirard, V.; Ottaviani, M.

2002-12-01

2-D fluid simulations of Scrape-Off Layer (SOL) turbulence with non constrained energy content (flux driven) are characterized by profile relaxation and strong outward bursts of density. The ballistic propagation extends well beyond the e-folding length of the SOL with a Mach number ∼ 0.04. Turbulence stabilisation is achieved by biasing part of the limiter surface. The critical radial extent to achieve this stabilisation is derived. This effect governs the size of the biased ring required to insulate the wall from the long range bursts of matter. The same characteristic scale also governs the critical size of Langmuir probe tips. For probe tips in excess of this size, the flux tube to the probe is found to be decoupled from the background plasma. (authors)

Scrape-off layer-induced beam density fluctuations and their effect on beam emission spectroscopy

Science.gov (United States)

Moulton, D.; Marandet, Y.; Tamain, P.; Dif-Pradalier, G.

2015-07-01

A statistical model is presented to calculate the magnitude of beam density fluctuations generated by a turbulent scrape-off layer (SOL). It is shown that the SOL can induce neutral beam density fluctuations of a similar magnitude to the plasma density fluctuations in the core, potentially corrupting beam emission spectroscopy measurements. The degree of corruption is quantified by combining simulations of beam and plasma density fluctuations inside a simulated measurement window. A change in pitch angle from the separatrix to the measurement window is found to reduce the effect of beam fluctuations, whose largest effect is to significantly reduce the measured correlation time.

Ion Temperature Measurements in the Tore Supra Scrape-Off Layer Using a Retarding Field Analyzer

International Nuclear Information System (INIS)

Kocan, M.; Gunn, J.P.; Pascal, J.Y.; Gauthier, E.

2010-01-01

The retarding field analyzer (RFA) is one of the only widely accepted diagnostics for measuring the ion temperature T i )in the tokamak scrape-off layer. An overview of the outstanding RFA performance over ten years of operation in Tore Supra tokamak is given and the validation of T i measurements is addressed. The RFA measurements in Tore Supra are found to be well reproducible. The ion-to-electron temperature ratio is higher than one at low-to-moderate ion-electron collisionality regime and converges to unity at high collisionality regime. (authors)

Physics of collisionless scrape-off-layer plasma during normal and off-normal Tokamak operating conditions

International Nuclear Information System (INIS)

Hassanein, A.; Konkashbaev, I.

1999-01-01

The structure of a collisionless scrape-off-layer (SOL) plasma in tokamak reactors is being studied to define the electron distribution function and the corresponding sheath potential between the divertor plate and the edge plasma. The collisionless model is shown to be valid during the thermal phase of a plasma disruption, as well as during the newly desired low-recycling normal phase of operation with low-density, high-temperature, edge plasma conditions. An analytical solution is developed by solving the Fokker-Planck equation for electron distribution and balance in the SOL. The solution is in good agreement with numerical studies using Monte-Carlo methods. The analytical solutions provide an insight to the role of different physical and geometrical processes in a collisionless SOL during disruptions and during the enhanced phase of normal operation over a wide range of parameters

Self-similar density turbulence in the TCV tokamak scrape-off layer

International Nuclear Information System (INIS)

Graves, J P; Horacek, J; Pitts, R A; Hopcraft, K I

2005-01-01

Plasma fluctuations in the scrape-off layer (SOL) of the TCV tokamak exhibit statistical properties which are universal across a broad range of discharge conditions. Electron density fluctuations, from just inside the magnetic separatrix to the plasma-wall interface, are described well by a gamma distributed random variable. The density fluctuations exhibit clear evidence of self-similarity in the far SOL, such that the corresponding probability density functions collapse upon renormalization solely by the mean particle density. This constitutes a demonstration that the amplitude of the density fluctuations is simply proportional to the mean density and is consistent with the further observation that the radial particle flux fluctuations scale solely with the mean density over two orders of magnitude. Such findings indicate that it may be possible to improve the prediction of transport in the critical plasma-wall interaction region of future large scale tokamaks. (letter to the editor)

Intermittent transport across the scrape-off layer: latest results from ASDEX Upgrade

International Nuclear Information System (INIS)

Kočan, M.; Müller, H.W.; Lunt, T.; Bernert, M.; Conway, G.D.; De Marné, P.; Eich, T.; Herrmann, A.; Kallenbach, A.; Maraschek, M.; Müller, S.; Nold, B.; Huang, Z.; Adámek, J.; Horacek, J.; Komm, M.; Allan, S.Y.; Elmore, S.; Gennrich, F.P; Mehlmann, F.

2013-01-01

We report the latest results of turbulence and transport studies in the ASDEX Upgrade scrape-off layer (SOL). Dissimilarity between the plasma and the floating potential fluctuations is studied experimentally and by gyrofluid simulations. Measurements by a retarding field analyser reveal that both, edge-localized mode (ELM) and turbulent filaments, convey hot ions over large radial distances in the SOL. The measured far SOL ELM ion temperature increases with the ELM energy, consistent with earlier observations that large ELMs deposit a large fraction of their energy outside the divertor. In the SOL, the ELM suppression by magnetic perturbations (MPs) results in lower ELM ion energy in the far SOL. At the same time, large filaments of ion saturation current are replaced by more continuous bursts. Splitting of the divertor strike zones observed by the infrared imaging in H-mode with MPs agree with predictions from the EMC3-Eirene simulations. This suggests that the ‘lobe’ structures due to perturbation fields observed near the X-point are not significantly affected by plasma screening, and can be described by a vacuum approach, as in the EMC3-Eirene. Finally, some effects of the MPs on the L-mode SOL are addressed. (paper)

A phenomenological model for cross-field plasma transport in non-ambipolar scrape-off layers

International Nuclear Information System (INIS)

LaBombard, B.; Grossman, A.A.; Conn, R.W.

1990-01-01

A simplified two-fluid transport model which includes phenomenological coefficients of particle diffusion, mobility, and thermal diffusivity is used to investigate the effects of nonambipolar particle transport on scrape-off layer (SOL) plasma profiles. A computer code (BSOLRAD3) has been written to iteratively solve for 2-D cross-field density, potential, and electron temperature profiles for arbitrary boundary conditions, including segments of 'limiters' that are electrically conducting or non-conducting. Numerical results are presented for two test cases: (1) a 1-D slab geometry showing the interdependency of the density, potential, and temperature gradient scale lengths on particle diffusion, mobility, and thermal diffusivity coefficients and limiter bias conditions, and (2) a 2-D geometry illustrating ExB plasma flow effects. It is shown that the SOL profiles can be quite sensitive to non-ambipolarity conditions imposed by the limiter and, in particular, whether the limiter surfaces are biased. Such effects, if overlooked in SOL transport analysis, can lead to erroreous conclusions about the magnitude of the local ambipolar diffusion coefficient. (orig.)

Turbulent transport regimes and the scrape-off layer heat flux width

Science.gov (United States)

Myra, J. R.; D'Ippolito, D. A.; Russell, D. A.

2015-04-01

Understanding the responsible mechanisms and resulting scaling of the scrape-off layer (SOL) heat flux width is important for predicting viable operating regimes in future tokamaks and for seeking possible mitigation schemes. In this paper, we present a qualitative and conceptual framework for understanding various regimes of edge/SOL turbulence and the role of turbulent transport as the mechanism for establishing the SOL heat flux width. Relevant considerations include the type and spectral characteristics of underlying instabilities, the location of the gradient drive relative to the SOL, the nonlinear saturation mechanism, and the parallel heat transport regime. We find a heat flux width scaling with major radius R that is generally positive, consistent with the previous findings [Connor et al., Nucl. Fusion 39, 169 (1999)]. The possible relationship of turbulence mechanisms to the neoclassical orbit width or heuristic drift mechanism in core energy confinement regimes known as low (L) mode and high (H) mode is considered, together with implications for the future experiments.

Turbulent transport regimes and the scrape-off layer heat flux width

International Nuclear Information System (INIS)

Myra, J. R.; D'Ippolito, D. A.; Russell, D. A.

2015-01-01

Understanding the responsible mechanisms and resulting scaling of the scrape-off layer (SOL) heat flux width is important for predicting viable operating regimes in future tokamaks and for seeking possible mitigation schemes. In this paper, we present a qualitative and conceptual framework for understanding various regimes of edge/SOL turbulence and the role of turbulent transport as the mechanism for establishing the SOL heat flux width. Relevant considerations include the type and spectral characteristics of underlying instabilities, the location of the gradient drive relative to the SOL, the nonlinear saturation mechanism, and the parallel heat transport regime. We find a heat flux width scaling with major radius R that is generally positive, consistent with the previous findings [Connor et al., Nucl. Fusion 39, 169 (1999)]. The possible relationship of turbulence mechanisms to the neoclassical orbit width or heuristic drift mechanism in core energy confinement regimes known as low (L) mode and high (H) mode is considered, together with implications for the future experiments

Measurement of flow in the scrape-off layer of TdeV

International Nuclear Information System (INIS)

MacLatchy, C.S.; Gunn, J.P.; Boucher, C.; Poirier, D.A.; Stansfield, B.L.; Zuzak, W.W.

1992-01-01

Two techniques are used to monitor the flow in the scrape-off layer of Tokamak de Varennes (TdeV); one is based on a new multipin Langmuir/Mach probe called Gundestrup while the other depends on the measurement of the upstream/downstream asymmetry of the power absorbed by a test limiter inserted into the plasma edge. Gundestrup has been used to measure the components of velocity parallel and perpendicular to the magnetic field as a function of the radial electric field. Both components vary linearly with the radial field and inversely as the magnetic field (U parallel ∝E r /B θ and U perpendicular to ∝E r /B). The pattern of power deposition on the test limiter implies that the flow is in the same direction as that measured by Gundestrup and the e-folding length for the power deposition is in agreement with Gundestrup measurements of temperature and density. The test limiter observations indicate that the flow reverses just inside the separatrix. (orig.)

Analysis of drift effects on the tokamak power scrape-off width using SOLPS-ITER

Science.gov (United States)

Meier, E. T.; Goldston, R. J.; Kaveeva, E. G.; Makowski, M. A.; Mordijck, S.; Rozhansky, V. A.; Senichenkov, I. Yu; Voskoboynikov, S. P.

2016-12-01

SOLPS-ITER, a comprehensive 2D scrape-off layer modeling package, is used to examine the physical mechanisms that set the scrape-off width ({λq} ) for inter-ELM power exhaust. Guided by Goldston’s heuristic drift (HD) model, which shows remarkable quantitative agreement with experimental data, this research examines drift effects on {λq} in a DIII-D H-mode magnetic equilibrium. As a numerical expedient, a low target recycling coefficient of 0.9 is used in the simulations, resulting in outer target plasma that is sheath limited instead of conduction limited as in the experiment. Scrape-off layer (SOL) particle diffusivity (D SOL) is scanned from 1 to 0.1 m2 s-1. Across this diffusivity range, outer divertor heat flux is dominated by a narrow (˜3-4 mm when mapped to the outer midplane) electron convection channel associated with thermoelectric current through the SOL from outer to inner divertor. An order-unity up-down ion pressure asymmetry allows net ion drift flux across the separatrix, facilitated by an artificial mechanism that mimics the anomalous electron transport required for overall ambipolarity in the HD model. At {{D}\\text{SOL}}=0.1 m2 s-1, the density fall-off length is similar to the electron temperature fall-off length, as predicted by the HD model and as seen experimentally. This research represents a step toward a deeper understanding of the power scrape-off width, and serves as a basis for extending fluid modeling to more experimentally relevant, high-collisionality regimes.

Langmuir probe measurements of the scrape-off plasma in ISX-A

International Nuclear Information System (INIS)

Namkung, W.; England, A.C.; Eldridge, O.C.

1978-11-01

A fixed double Langmuir probe was used to investigate the temporal behavior of the scrape-off plasma in the ISX-A tokamak. During gas puffing, the ion saturation current dropped rapidly to a very low level while the line average density showed a steady increase. This sudden transition was due mainly to a density change of more than a factor of five while the electron temperature remained relatively constant at approximately 10 eV. This behavior was easily observed at points away from the limiter with mild and moderate gas puffing rates, and near the inner edge of the limiter with strong gas puffing. In order to explain the phenomenon, it is suggested that there may be two distinct layers in the scrape-off plasma and that the boundary between the layers moves inward toward the limiter. The existence of the boundary has been confirmed indirectly by sudden shifts of the plasma during feedback control experiments

Scrape-off layer based modelling of the density limit in beryllated JET limiter discharges

International Nuclear Information System (INIS)

Borrass, K.; Campbell, D.J.; Clement, S.; Vlases, G.C.

1993-01-01

The paper gives a scrape-off layer based interpretation of the density limit in beryllated JET limiter discharges. In these discharges, JET edge parameters show a complicated time evolution as the density limit is approached and the limit is manifested as a non-disruptive density maximum which cannot be exceeded by enhanced gas puffing. The occurrence of Marfes, the manner of density control and details of recycling are essential elements of the interpretation. Scalings for the maximum density are given and compared with JET data. The relation to disruptive density limits, previously observed in JET carbon limiter discharges, and to density limits in divertor discharges is discussed. (author). 18 refs, 10 figs, 1 tab

The scrape-off layer in a finite-aspect-ratio Torus: The influence of limiter position

International Nuclear Information System (INIS)

Harbour, P.J.; Loarte, A.

1995-01-01

The effect on the scrape-off layer (SOL) of changing the position of a tokamak limiter from the low field side (LFS) to the high field side (HFS) of the plasma is considered. Conservation of magnetics flux in the SOL requires that the area, A parallel , for flow of particles and energy parallel to the magnetic field, be smaller on the HFS. The effect that this reduction in A parallel has on the SOL is that, when the limiter is on the HFS, as compared with the LFS, then the characteristic scrape-off thickness is increased and the plasma particle and energy densities are higher. Such increases are described. They were observed in an experiment in JET in which the plasma was limited first on the LFS and then, during the same discharge, on the HFS. The magnitude of the effect was larger than expected, with the line integrated density of the SOL, nλ n , having an average increase by a factor of 5.8 ± 1.1, and an increase by a factor of 7 at the respective limiter. Moreover, there was an increase in the characteristic scrape-off thickness for power flow, λ p , by a factor of 2.5 ± 0.4 on average, and a corresponding increase by a factor of 3.0 at the respective limiter. Such an increase in nλ n can substantially improve the screening of recycled particles and can increase wall pumping, although not strongly in the experiments described, which were in helium to avoid these effects. The large increase in λ p measured in JET is useful in spreading power over a larger area of a limiter on the HFS. Evidence is presented which suggests that either the observed enhancement of the effect on the SOL above expectations is due to a reduction in the Mach number at the limiter sheath when on the HFS or there are fundamental problems with the modelling procedure usually used for the SOL. Related experiments are discussed. (author). 29 refs, 3 figs, 3 tabs

Studies of mobile dust in scrape-off layer plasmas using silica aerogel collectors

Energy Technology Data Exchange (ETDEWEB)

Bergsaker, H., E-mail: henricb@kth.se [Division of Space and Plasma Physics, Association EURATOM-VR, School of Electrical Engineering, Royal Institute of Technology KTH, SE-10044 Stockholm (Sweden); Ratynskaia, S. [Division of Space and Plasma Physics, Association EURATOM-VR, School of Electrical Engineering, Royal Institute of Technology KTH, SE-10044 Stockholm (Sweden); Litnovsky, A. [Institut fur Energieforschung - Plasmaphysik, Forschungszentrum Julich, Trilateral Euregio Cluster, Association EURATOM-FZ Julich, D-52425 Julich (Germany); Ogata, D. [Division of Space and Plasma Physics, Association EURATOM-VR, School of Electrical Engineering, Royal Institute of Technology KTH, SE-10044 Stockholm (Sweden); Sahle, W. [Functional Materials Division, KTH-Electrum 229, Isafjordsgatan 22, SE-16440 Stockholm (Sweden)

2011-08-01

Dust capture with ultralow density silica aerogel collectors is a new method, which allows time resolved in situ capture of dust particles in the scrape-off layers of fusion devices, without substantially damaging the particles. Particle composition and morphology, particle flux densities and particle velocity distributions can be determined through appropriate analysis of the aerogel surfaces after exposure. The method has been applied in comparative studies of intrinsic dust in the TEXTOR tokamak and in the Extrap T2R reversed field pinch. The analysis methods have been mainly optical microscopy and SEM. The method is shown to be applicable in both devices and the results are tentatively compared between the two plasma devices, which are very different in terms of edge plasma conditions, time scale, geometry and wall materials.

Modelling of impurity production and transport in the scrape-off layer of a high density limiter tokamak

International Nuclear Information System (INIS)

Zagorski, R.; Romanelli, F.

1996-01-01

A simple analytical model is presented that describes impurity ion production and transport in the tokamak scrape-off layer (SOL). The equations of the model are solved analytically in the test particle approximation. The solution, as a function of different plasma parameters and target materials, is discussed in the case in which the background plasma is described by the simple SOL model and a comparison between the model and the numerical results of a 2-D multifluid code is presented. (author). 18 refs, 8 figs, 2 tabs

ERO-TEXTOR. 3D-Monte Carlo code for local impurity-modeling in the scrape-off-layer of TEXTOR. Version 2.0

International Nuclear Information System (INIS)

Koegler, U.; Winter, J.

1997-03-01

The ERO-TEXTOR code is described in detail. The code solves the kinetic equations of impurities in the scrape-off layer of a tokamak plasma in the vicinity of material surfaces like limiters or divertors. A relaxation time ansatz in the traced impurity limit is chosen, taking the gyro-motion of the particles into account. Since the background plasma is slightly non-maxwellian at the plasma edge higher order corrections (thermal forces) to the relaxation time ansatz are also considered. Background plasma parameters are calculated from a simple plasma model, i.e. the one dimensional continuity and momentum equations are used to derive the local electron density, the local flow velocity and the pre-sheath and sheath electric fields. Since these calculations are not done in a selfconsistent way, the measured values of electron density and temperature are used as basic input to derive the dependency of these quantities. The regarded magnetic topology is still straight and uniform. Also detailed account is given to the plasma surface interaction and the erosion/deposition processes. A linear differential equation model for multi species impact on a material surface has been developed and is used in a discrete time step approximation. External databases include the ionization rates for atomic species, molecular processes of methane and silane molecules and the sputtering and reflection yields, which are taken from binary collision calculation codes (e.g. TRIM) or from semi-empirical fits (e.g. the Bodhansky and Yamamura fits). (orig.)

A theoretical interpretation of the main scrape-off layer heat-flux width scaling for tokamak inner-wall limited plasmas

Czech Academy of Sciences Publication Activity Database

Halpern, F.D.; Horáček, Jan; Pitts, R. A.; Ricci, P.

2016-01-01

Roč. 58, č. 8 (2016), č. článku 084003. ISSN 0741-3335 R&D Projects: GA ČR(CZ) GAP205/12/2327 Institutional support: RVO:61389021 Keywords : edge plasma * heat-flux width * scrape-off layer Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 2.392, year: 2016 http://iopscience.iop.org/article/10.1088/0741-3335/58/8/084003/meta

Probability distribution functions for intermittent scrape-off layer plasma fluctuations

Science.gov (United States)

Theodorsen, A.; Garcia, O. E.

2018-03-01

A stochastic model for intermittent fluctuations in the scrape-off layer of magnetically confined plasmas has been constructed based on a super-position of uncorrelated pulses arriving according to a Poisson process. In the most common applications of the model, the pulse amplitudes are assumed exponentially distributed, supported by conditional averaging of large-amplitude fluctuations in experimental measurement data. This basic assumption has two potential limitations. First, statistical analysis of measurement data using conditional averaging only reveals the tail of the amplitude distribution to be exponentially distributed. Second, exponentially distributed amplitudes leads to a positive definite signal which cannot capture fluctuations in for example electric potential and radial velocity. Assuming pulse amplitudes which are not positive definite often make finding a closed form for the probability density function (PDF) difficult, even if the characteristic function remains relatively simple. Thus estimating model parameters requires an approach based on the characteristic function, not the PDF. In this contribution, the effect of changing the amplitude distribution on the moments, PDF and characteristic function of the process is investigated and a parameter estimation method using the empirical characteristic function is presented and tested on synthetically generated data. This proves valuable for describing intermittent fluctuations of all plasma parameters in the boundary region of magnetized plasmas.

Coupled two-dimensional edge-plasma and neutral gas modelling of the DIII-D scrape-off-layer

International Nuclear Information System (INIS)

Maingi, R.; Gilligan, J.; Hankins, O.; Rensink, M.; Owen, L.; Klepper, C.; Mioduszewski, P.

1992-01-01

This paper reports that in order to do consistent scrape-off-layer plasma and neutral transport calculations, the 2-D fluid code, B2 has been externally coupled to the neutral transport code, DEGAS, for Dlll-D. The coupling procedure is similar to recent simulations done for TFTR, Tore Supra, and ClT. An averaged source approach is utilized to allow convergence between the two codes. Initial comparison of plasma quantities between the coupled code set and the B2 code alone shows that a colder, denser plasma may exist at the divertor targets than predicted by the B2 code with its internal recycling model

Particle and heat balance analysis in scrape-off and divertor regions of the JFT-2M tokamak

International Nuclear Information System (INIS)

Nagashima, K.; Shoji, T.; Tamai, H.; Miura, Y.; Takenaga, H.; Maeda, H.

1995-01-01

Particle and heat balance in the scrape-off layer and the divertor region were studied in the JFT-2M tokamak. Using particle and energy conservation laws, particle and heat diffusivities perpendicular to the flux surface were evaluated just outside the magnetic separatrix. It was found that the particle diffusivity decreases with increasing electron density in the scrape-off layer and decreases by a factor of 2-3 in the H-mode phase as compared with that in L-mode. The heat diffusivity has almost the same dependence on the electron density. The ratio of the heat diffusivity to the particle diffusivity is about 2. ((orig.))

Dual cascade and minimum enstrophy state in the tokamak scrape-off layer

International Nuclear Information System (INIS)

Mattor, N.; Cohen, R.H.; Xu, X.Q.

1993-01-01

In the Tokamak Scrape-off layer (SOL), there is experimental, theoretical, and computational evidence of an inverse energy cascade, wherein fluctuation energy transfers nonlinearly to large scale lengths. If the inverse cascade proceeds to the largest scales, it gives transport which is inherently nonlocal, precluding standard descriptions with local transport coefficients. This includes DIA based renormalization theories, γ/k 2 open-quotes mixing lengthclose quotes theories, and spectral or pseudo-spectral codes, all of which tend to involve a two-scale assumption, that turbulence acts on very short time and length scales relative to the equilibrium. The two-scale assumption is violated by turbulence undergoing a significant inverse cascade, and a different approach is called for. The authors postulate that the net effect of such turbulence is not local transport, but rather to supply the equilibrium with a steady source of energy at the minimum enstrophy. The form of the supplied energy is assessed through a variational calculation, which gives an equation for the equilibrium velocity profile, ∇ 2 V = λ 2 V, where λ 2 is an undetermined Lagrange multiplier. For a slab model, the solution in the SOL is V = V a exp[-λ(r-a)]y, where V a is the poloidal velocity at the SOL/edge interface. This velocity (from E x B in the simple model), leads to the potential profile, φ = -(V a B/λc)exp[-λ(r-a)]. For field lines connected to an endplate eφ = ΛT e , (where Λ ∼ 4 is nearly constant) giving also the T e profile. Thus, the profiles are given and the transport problem is solved, up to the two unknown constants λ and V a . One relation comes from heat balance. There are several candidates for the second constant, and the authors present numerical simulations which evaluate these

Investigation of a limiter scrape-off layer and its screening effect on LIBTOR tokamak

International Nuclear Information System (INIS)

Leonov, V.M.; Malakhov, N.P.; Alabyad, A.M.

1986-01-01

The main purpose of this work is to investigate screening properties of the limiter scrape-off layer (LSL), define the optimum width of this layer and investigate how energy and particle fluxes transfer from plasma to surrounding material surfaces from in the Libtor tokamak. For this, two moving rail molybdenum limiters (large as a working limiter and small as a probe), equipped with shunts and thermocouples were placed on the bottom side of tokamak at 980 deg apart the torus. The main results of the work are as follows: the introduction of a limiter allows an essential shielding of the chamber wall from the interaction with plasma and a reduction in the impurity influx into the plasma column. The main mechanism of the limiter erosion in the stationary part of a discharge is the ion sputtering. An active control over the limiter sputtering, over the heat and particle fluxes onto the limiter and over the plasma confinement time can be found to be of importance for the prospects of the limiter application as an alternative to the divertor in the tokamak-reactor

Turbulent fluctuations and radial transport in the scrape-off layer of the ASDEX tokamak

Energy Technology Data Exchange (ETDEWEB)

Endler, M [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, 85740 Garching (Germany); Giannone, L. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, 85740 Garching (Germany); McCormick, K [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, 85740 Garching (Germany); Niedermeyer, H [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, 85740 Garching (Germany); Rudyj, A [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, 85740 Garching (Germany); Theimer, G [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, 85740 Garching (Germany); Tsois, N [NCSR ` Demokritos` , Athens (Greece); ASDEX Team

1995-04-01

Electrostatic fluctuations have been measured in the scrape-off layer of ASDEX by Langmuir probes and by observation of H{sub {alpha}} light with high poloidal and temporal resolution. It was demonstrated that these fluctuations contribute a significant, if not dominant, fraction of the ``anomalous`` radial particle transport. A model for an instability mechanism specific to the SOL is presented including density, temperature and electric potential fluctuations. From this model mixing length estimates for the radial transport and resulting density and pressure gradients in the SOL are derived and compared to measurements in the mid-plane and in the divertor of ASDEX. In spite of several simplifications in the model a quantitative agreement up to factors of 1-3 and a qualitative agreement for variations of discharge parameters is achieved between the model predictions and the measurements. ((orig.)).

Turbulent fluctuations and radial transport in the scrape-off layer of the ASDEX tokamak

International Nuclear Information System (INIS)

Endler, M.; Giannone, L.; McCormick, K.; Niedermeyer, H.; Rudyj, A.; Theimer, G.; Tsois, N.

1995-01-01

Electrostatic fluctuations have been measured in the scrape-off layer of ASDEX by Langmuir probes and by observation of H α light with high poloidal and temporal resolution. It was demonstrated that these fluctuations contribute a significant, if not dominant, fraction of the ''anomalous'' radial particle transport. A model for an instability mechanism specific to the SOL is presented including density, temperature and electric potential fluctuations. From this model mixing length estimates for the radial transport and resulting density and pressure gradients in the SOL are derived and compared to measurements in the mid-plane and in the divertor of ASDEX. In spite of several simplifications in the model a quantitative agreement up to factors of 1-3 and a qualitative agreement for variations of discharge parameters is achieved between the model predictions and the measurements. ((orig.))

Measurements and modelling of electrostatic fluctuations in the scrape-off layer of ASDEX

Energy Technology Data Exchange (ETDEWEB)

Endler, M; Niedermeyer, H; Giannone, L.; Holzhauer, E; Rudyj, A; Theimer, G; Tsois, N [Association Euratom-Max-Planck-Institut fuer Plasmaphysik, Garching (Germany); ASDEX Team

1995-11-01

In the edge plasma of the ASDEX tokamak, electrostatic fluctuations were observed with Langmuir probes and in H{sub {alpha}} light with high poloidal and temporal resolution. These fluctuations contribute a significant fraction to the `anomalous` radial particle transport in the scrape-off layer (SOL). The basic properties and the dependence of the fluctuations parameters on the discharge conditions are documented. A model for an instability mechanism specific to the SOL is introduced and the experimentally observed fluctuation parameters are compared with the predictions of the linearized version of this model. For plasma temperatures above {approx} 10eV in the SOL the observed parameter dependences of the fluctuations are well reproduced by the model. By mixing length arguments the radial transport and the resulting density and pressure gradients in the SOL are estimated from the model. Their dependence on plasma temperature and density qualitatively agrees with the behaviour observed in ohmic discharges on ASDEX. (author). 54 refs, 25 figs.

Measurements and modelling of electrostatic fluctuations in the scrape-off layer of ASDEX

International Nuclear Information System (INIS)

Endler, M.; Niedermeyer, H.; Giannone, L.; Holzhauer, E.; Rudyj, A.; Theimer, G.; Tsois, N.

1995-01-01

In the edge plasma of the ASDEX tokamak, electrostatic fluctuations were observed with Langmuir probes and in H α light with high poloidal and temporal resolution. These fluctuations contribute a significant fraction to the 'anomalous' radial particle transport in the scrape-off layer (SOL). The basic properties and the dependence of the fluctuations parameters on the discharge conditions are documented. A model for an instability mechanism specific to the SOL is introduced and the experimentally observed fluctuation parameters are compared with the predictions of the linearized version of this model. For plasma temperatures above ∼ 10eV in the SOL the observed parameter dependences of the fluctuations are well reproduced by the model. By mixing length arguments the radial transport and the resulting density and pressure gradients in the SOL are estimated from the model. Their dependence on plasma temperature and density qualitatively agrees with the behaviour observed in ohmic discharges on ASDEX. (author). 54 refs, 25 figs

Measurements and simulations of scrape-off layer flows in the DIII-D Tokamak

Energy Technology Data Exchange (ETDEWEB)

Groth, M. [Lawrence Livermore National Laboratory, General Atomics, P.O. Box 85608, Livermore, San Diego, CA 92186-5608 (United States); General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States)], E-mail: groth@fusion.gat.com; Porter, G.D. [Lawrence Livermore National Laboratory, General Atomics, P.O. Box 85608, Livermore, San Diego, CA 92186-5608 (United States); Boedo, J.A. [University of California San Diego, La Jolla, CA 92093 (United States); Brooks, N.H. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Isler, R.C. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); West, W.P.; Bray, B.D. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Fenstermacher, M.E. [Lawrence Livermore National Laboratory, General Atomics, P.O. Box 85608, Livermore, San Diego, CA 92186-5608 (United States); Groebner, R.J.; Leonard, A.W. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Moyer, R.A. [University of California San Diego, La Jolla, CA 92093 (United States); Rognlien, T.D. [Lawrence Livermore National Laboratory, General Atomics, P.O. Box 85608, Livermore, San Diego, CA 92186-5608 (United States); Watkins, J.G. [Sandia National Laboratory, P.O. Box 5800, Albuquerque, NM 87185 (United States); Yu, J.H. [University of California San Diego, La Jolla, CA 92093 (United States)

2009-06-15

Flow velocities of the order 10-20 km/s in the direction of the high-field side divertor have been measured for deuterons and low charge-state carbon ions in the scrape-off layer at the crown of low-density L-mode plasmas, suggesting that these carbon ions at the crown move with the background plasma flow. Simulations with the multi-fluid edge code UEDGE including cross-field drifts due to E x B and B x {nabla}B yield calculated divertor conditions which are more consistent with the measurements, but flows at the crown that are stagnant or in the opposite direction than observed. The simulations indicate that both the ion temperature gradient force and deuteron frictional drag play a role in determining the flow direction and magnitude of low charge-state carbon ions. The effect of the assumed radial transport model, toroidal core rotation, and neutral pumping at the divertor plates on the flow at the crown is investigated.

Poloidal electric field and variation of radial transport during ICRF heating in the JET scrape-off layer

International Nuclear Information System (INIS)

Clement, S.; Tagle, J.A.; Bures, M.; Vince, J.; Kock, L. de; Stangeby, P.C.

1989-01-01

The highly anomalous perpendicular transport in the plasma edge of a tokamak is generally attributed to plasma turbulence, primarily to density and electrostatic potential fluctuations. The edge transport could be modified by changing the geometry of objects in contact with the plasma (limiters, radio frequency antennae ...) and during additional heating experiments. Poloidal asymmetries in the scrape-off layer (SOL) in tokamaks using poloidal limiters (eg. ALCATOR-C) have been recently reported, indicating a poloidal asymmetry in cross-field transport. A poloidal ring limiter obstructs communications between different flux tubes in the SOL, thus permitting poloidal asymmetries in n e and T e to develop if D perpendicular is θ-dependent. When JET was operated with discrete limiters, equivalent to a single toroidal limiter at the outside mid-plane, little poloidal variation in the SOL plasma properties was observed. Currently JET is operated with two complete toroidal belt limiters located approximately one meter above and below the outside mid-plane. This configuration breaks the SOL into two regions: the low field side SOL (LFS), between the limiters, and the rest of the SOL on the high field side (HFS). Differences on the scrape-off lengths in the two SOLs are reported here, indicating that cross-field transport is faster on the LFS-SOL, in agreement with observations made on ASDEX and T-10. (author) 8 refs., 6 figs

Influence of plasma background including neutrals on scrape-off layer filaments using 3D simulations

Directory of Open Access Journals (Sweden)

D. Schwörer

2017-08-01

Full Text Available This paper investigates the effect of the plasma background, including neutrals in a self-consistent way, on filaments in the scrape-off layer (SOL of fusion devices. A strong dependency of filament motion on background density and temperature is observed. The radial filament motion shows an increase in velocity with decreasing background density and increasing background temperature. In the simulations presented here, three neutral-filament interaction models have been compared, one with a static neutral background, one with no interaction between filaments and neutrals, and one co-evolving the neutrals self consistently with the filaments. With the background conditions employed here, which do not show detachment, there are no significant effects of neutrals on filaments, as by the time the filament reaches maximum velocity, the neutral density has not changed significantly.

Gyrofluid computations of filament dynamics in tokamak scrape-off layers

International Nuclear Information System (INIS)

Wiesenberger, M.

2014-01-01

This work contributes to the theoretical modelling, the simulation, and the analysis of plasma filaments in the scrape-off layer of magnetic fusion devices. A gyrofluid model that explicitly incorporates high fluctuation amplitudes and finite Larmor radius effects is used. First, the derivation of gyrofluid equations is thoroughly reviewed. Lie transform perturbation methods are able to remove the fast space-time scales associated with the fast gyration of particles in a strong background magnetic field. This form of perturbation theory conserves the Hamiltonian nature of the system while not being restricted to canonical coordinates. Variational methods lead to the gyrofluid equations. We explicitly derive an energy theorem and consistency equations that are necessary for the theorem to hold. The next step is to carefully choose, describe, and implement numerical methods necessary for computational studies. The discontinuous Galerkin methods have proven very flexible and easy to implement in our newly developed formulation. Furthermore, we show how field-aligned derivatives can be numerically treated in a cylindrical coordinate system. The numerical code is able to harness the computational power of today's parallel hardware architecture. A GPU, an OpenMP, and an MPI version of the source code for two- and three-dimensional simulations have been carefully planned, implemented, and tested. In the course of this work, we develop a novel conservative space discretization of the two-dimensional Poisson bracket extending the well-known Arakawa scheme to a high order discontinuous Galerkin method. Together with an existing discretization for the Laplacian we are able to discretize the two-dimensional incompressible Navier-Stokes and Euler equations. Simulations confirm the high order and the conservative properties of our method. Finally, we show that we can numerically solve the nonlinear polarization equation in the context of a mass and energy conserving, two

Steady-state and time-dependent modelling of parallel transport in the scrape-off layer

DEFF Research Database (Denmark)

Havlickova, E.; Fundamenski, W.; Naulin, Volker

2011-01-01

The one-dimensional fluid code SOLF1D has been used for modelling of plasma transport in the scrape-off layer (SOL) along magnetic field lines, both in steady state and under transient conditions that arise due to plasma turbulence. The presented work summarizes results of SOLF1D with attention...... given to transient parallel transport which reveals two distinct time scales due to the transport mechanisms of convection and diffusion. Time-dependent modelling combined with the effect of ballooning shows propagation of particles along the magnetic field line with Mach number up to M ≈ 1...... temperature calculated in SOLF1D is compared with the approximative model used in the turbulence code ESEL both for steady-state and turbulent SOL. Dynamics of the parallel transport are investigated for a simple transient event simulating the propagation of particles and energy to the targets from a blob...

Analytical studies of multidimensional plasma transport in the scrape-off layer

International Nuclear Information System (INIS)

Tendler, M.; Rozhansky, V.

1992-01-01

2-D effects originating from the lack of geometrical overlapping of equipotential and magnetic surfaces are examined. It is shown that poloidal rotation in the scrape-off layer (SOL), which emerges due to the drift caused by the radial electric field, shifts the maximum of the plasma density in the SOL out of the equatorial midplane provided it is accompanied by a poloidally asymmetric turbulent diffusion. Another effect resulting in asymmetry relates the significant enhancement of the plasma flow to the ion side of a limiter (and the corresponding reduction to the electron side) with the momentum balance in the SOL. A rigorous mathematical theory has been developed in order to assess the 3-D effect quantitatively. In the SOL global ambipolarity has to be maintained. Therefore flux surface average radial current cancels at the separatrix. Employing the toroidal and the parallel components of momentum balance, it is shown that the ambipolarity constraint on open field lines yields the ion sonic flow driven in the same direction as the inductive current. This results in the reduction to almost zero of a flow toward the electron side of a limiter and the almost two-fold increase of a flow toward the ion side. (orig.)

Scrape-off layer transport and deposition studies in DIII-D

International Nuclear Information System (INIS)

Groth, M.; Allen, S. L.; Fenstermacher, M. E.; Lasnier, C. J.; Porter, G. D.; Rensink, M. E.; Rognlien, T. D.; Boedo, J. A.; Rudakov, D. L.; Brooks, N. H.; Groebner, R. J.; Leonard, A. W.; West, W. P.; Elder, J. D.; McLean, A. G.; Lisgo, S.; Stangeby, P. C.; Wampler, W. R.; Watkins, J. G.; Whyte, D. G.

2007-01-01

Trace 13 CH 4 injection experiments into the main scrape-off layer (SOL) of low density L-mode and high-density H-mode plasmas have been performed in the DIII-D tokamak [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] to mimic the transport and deposition of carbon arising from a main chamber sputtering source. These experiments indicated entrainment of the injected carbon in plasma flow in the main SOL, and transport toward the inner divertor. Ex situ surface analysis showed enhanced 13 C surface concentration at the corner formed by the divertor floor and the angled target plate of the inner divertor in L-mode; in H-mode high surface concentration was found both at the corner and along the surface bounding the private flux region inboard of the outer strike point. Interpretative modeling was made consistent with these experimental results by imposing a parallel carbon ion flow in the main SOL toward the inner target, and a radial pinch toward the separatrix. Predictive modeling carried out to better understand the underlying plasma transport processes suggests that the deuterium flow in the main SOL is related to the degree of detachment of the inner divertor leg. These simulations show that carbon ions are entrained with the deuteron flow in the main SOL via frictional coupling, but higher charge-state carbon ions may be suspended upstream of the inner divertor X-point region due to balance of the friction force and the ion temperature gradient force

Scrape-off layer plasma modeling for the DIII-D tokamak

International Nuclear Information System (INIS)

Porter, G.D.; Rognlien, T.D.; Allen, S.L.

1994-09-01

The behavior of the scrape-off layer (SOL) region in tokamaks is believed to play an important role determining the overall device performance. In addition, control of the exhaust power has become one of the most important issues in the design of future devices such as ITER and TPX. This paper presents the results of application of 2-D fluid models to the DII-D tokamak, and research into the importance of processes which are inadequately treated in the fluid models. Comparison of measured and simulated profiles of SOL plasma parameters suggest the physics model contained in the UEDGE code is sufficient to simulate plasmas which are attached to the divertor plates. Experimental evidence suggests the presence of enhanced plasma recombination and momentum removal leading to the existence of detached plasma states. UEDGE simulation of these plasmas obtains a bifurcation to a low temperature plasma at the divertor, but the plasma remains attached. Understanding the physics of this detachment is important for the design of future devices. Analytic studies of the behavior of SOL plasmas enhance our understanding beyond that achieved with fluid modeling. Analysis of the effect of drifts on sheath structure suggest these drifts may play a role in the detachment process. Analysis of the turbulent-transport equations indicate a bifurcation which is qualitatively similar to the experimentally different behavior of the L- and H-mode SOL. Electrostatic simulations of conducting wall modes suggest possible control of the SOL width by biasing

Measurements and Simulations of Scrape-off Layer Flows in the DIII-D Tokamak

International Nuclear Information System (INIS)

Groth, M.; Porter, G.D.; Boedo, J.A.; Brooks, N.H.; Isler, Ralph C.; West, W.P.; Bray, B.D.; Fenstermacher, M.E.; Groebner, R.J.; Leonard, A.W.; Moyer, R.A.; Rognlien, T.D.; Watkins, J.G.; Yu, J.H.

2009-01-01

Flow velocities of the order 10-20 km/s in the direction of the high-field side divertor have been measured for deuterons and low charge-state carbon ions in the scrape-off layer at the crown of low-density L-mode plasmas, suggesting that these carbon ions at the crown move with the background plasma flow. Simulations with the multi-fluid edge code UEDGE including cross-field drifts due to E x B and B x del B yield calculated divertor conditions which are more consistent with the measurements, but flows at the crown that are stagnant or in the opposite direction than observed. The simulations indicate that both the ion temperature gradient force and deuteron frictional drag play a role in determining the flow direction and magnitude of low charge-state carbon ions. The effect of the assumed radial transport model, toroidal core rotation, and neutral pumping at the divertor plates on the flow at the crown is investigated. (C) 2009 Elsevier B.V. All rights reserved.

Detection of lower hybrid waves in the scrape-off layer of tokamak plasmas with microwave backscattering

International Nuclear Information System (INIS)

Baek, S. G.; Shiraiwa, S.; Parker, R. R.; Bonoli, P. T.; Marmar, E. S.; Wallace, G. M.; Lau, C.; Dominguez, A.; Kramer, G. J.

2014-01-01

Microwave backscattering experiments have been performed on the Alcator C-Mod tokamak in order to investigate the propagation of lower hybrid (LH) waves in reactor-relevant, high-density plasmas. When the line-averaged density is raised above 1 × 10 20 m –3 , lower hybrid current drive efficiency is found to be lower than expected [Wallace et al., Phys. Plasmas 19, 062505 (2012)] and LH power is thought to be dissipated at the plasma edge. Using a single channel (60 GHz) ordinary-mode (O-mode) reflectometer system, we demonstrate radially localized LH wave measurements in the scrape-off layer of high density plasmas (n ¯ e  ≳ 0.9×10 20  m −3 ). Measured backscattered O-mode power varies depending on the magnetic field line mapping, suggesting the resonance cone propagation of LH waves. Backscattered power is also sensitive to variations in plasma density and the launched parallel refractive index of the LH waves. LH ray-tracing simulations have been carried out to interpret the observed variations. To understand the measured LH waves in regions not magnetically connected to the launcher, two hypotheses are examined. One is the weak single pass absorption and the other is scattering of LH waves by non-linear effects

Drift-based scrape-off particle width in X-point geometry

Science.gov (United States)

Reiser, D.; Eich, T.

2017-04-01

The Goldston heuristic estimate of the scrape-off layer width (Goldston 2012 Nucl. Fusion 52 013009) is reconsidered using a fluid description for the plasma dynamics. The basic ingredient is the inclusion of a compressible diamagnetic drift for the particle cross field transport. Instead of testing the heuristic model in a sophisticated numerical simulation including several physical mechanisms working together, the purpose of this work is to point out basic consequences for a drift-dominated cross field transport using a reduced fluid model. To evaluate the model equations and prepare them for subsequent numerical solution a specific analytical model for 2D magnetic field configurations with X-points is employed. In a first step parameter scans in high-resolution grids for isothermal plasmas are done to assess the basic formulas of the heuristic model with respect to the functional dependence of the scrape-off width on the poloidal magnetic field and plasma temperature. Particular features in the 2D-fluid calculations—especially the appearance of supersonic parallel flows and shock wave like bifurcational jumps—are discussed and can be understood partly in the framework of a reduced 1D model. The resulting semi-analytical findings might give hints for experimental proof and implementation in more elaborated fluid simulations.

Numerical analysis of the impact of an RF sheath on the Scrape-Off Layer in 2D and 3D turbulence simulations

Directory of Open Access Journals (Sweden)

P. Tamain

2017-08-01

Full Text Available Motivated by Radio Frequency (RF heating studies, the response of the plasma of tokamaks to the presence of a locally polarized limiter is studied. In a first part, we use the TOKAM3X3D global edge turbulence code to analyse the impact of such biasing in a realistic geometry. Key features of experimental observations are qualitatively recovered, especially the extension of a potential and density perturbation on long, but finite, distances along connected field lines. The perturbation is also found to extend in the transverse direction. Both observations demonstrate the influence of perpendicular current loops on the plasma confirming the need for an accurate description in reduced models. In a second part, we use the TOKAM2D slab turbulence code to determine the validity of using a transverse Ohm's law for this purpose. Results indicate that a local Ohm's law with a constant and uniform perpendicular resistivity appears at least as an oversimplified description of perpendicular charge transport in a turbulent Scrape-Off Layer.

Comparison of Scrape-off Layer Turbulence in Alcator C-Mod with Three Dimensional Gyrofluid Computations

International Nuclear Information System (INIS)

Zweben, S.J.; Scott, B.D.; Terry, J.L.; LaBombard, B.; Hughes, J.W.; Stotler, D.P.

2009-01-01

This paper describes quantitative comparisons between turbulence measured in the scrape-off layer (SOL) of Alcator C-Mod (S. Scott, A. Bader, M. Bakhtiari et al., Nucl. Fusion 47, S598 (2007)) and three dimensional computations using electromagnetic gyrofluid equations in a two-dimensional tokamak geometry. These comparisons were made for the outer midplane SOL for a set of inner-wall limited, near-circular Ohmic plasmas. The B field and plasma density were varied to assess gyroradius and collisionality scaling. The poloidal and radial correlation lengths in the experiment and computation agreed to within a factor of 2 and did not vary significantly with either B or density. The radial and poloidal propagation speeds and the frequency spectra and poloidal k-spectra also agreed fairly well. However, the autocorrelation times and relative Da fluctuation levels were higher in the experiment by more than a factor of 2. Possible causes for these disagreements are discussed.

Scrape-off measurements during Alfven wave heating in the TCA tokamak

International Nuclear Information System (INIS)

Hofmann, F.; Hollenstein, C.; Joye, B.; Lietti, A.; Lister, J.B.; Pochelon, A.; Gimzewski, J.K.; Veprek, S.

1984-01-01

Plasma parameters and impurity fluxes in the scrape-off layer of the TCA tokamak have been measured during Alfven wave heating. Langmuir probes are used to measure electron density, electron temperature and plasma potential. Collection probes, in conjunction with XPS surface analysis, are used to determine impurity fluxes and ion impact energies. During RF heating, the electron edge temperature rises, the plasma potential drops and impurity fluxes are enhanced. Probe erosion due to impurity sputtering is clearly observed. The measurements are correlated with other diagnostics on TCA. (orig.)

A model for a scrape-off-layer low-high (L-H) mode transition

International Nuclear Information System (INIS)

Cohen, R.H.; Xu, X.

1995-01-01

Increasing the radial mode number has a stabilizing effect on the conducting-wall and curvature-driven interchange modes in a tokamak scrape-off layer (SOL), arising from the increased polarization response. Such an effect is naturally imposed as the SOL width is decreased, and for a narrow-enough SOL, the stabilizing effect is stronger than the increase in the instability drives. By combining a mixing-length estimate for the thermal diffusivity with energy conservation and heat conduction equations and the condition of continuity of the heat flux at the separatrix, it is found that the resultant turbulence-transport system admits two solutions, one stable and one unstable, at different SOL widths; the inclusion of additional physics can add a second stable root at lower width. These roots are plausibly identified with SOL behavior in low (L) and high (H) modes. Particularly when a model is introduced for finite-β, finite-k parallel effects on the modes, a power threshold for transition to the narrower root is obtained, suggesting a possible L-H transition mechanism. The non-monotonic dependence of the turbulent heat flux vs SOL width and the possibility of multiple solutions for the equilibrium SOL width are verified with nonlinear simulations. copyright 1995 American Institute of Physics

Determining advection mechanism of plasma filaments in the scrape-off layer of MAST

International Nuclear Information System (INIS)

Higgins, D; Hnat, B; Kirk, A; Tamain, P; Ben Ayed, N

2012-01-01

The scrape-off layer (SOL) of fusion devices is typically composed of filamentary structures that propagate with a high radial velocity away from the bulk plasma. When radial and parallel transport times are comparable, these coherent structures constitute an intermittent heat and particle flux which can reach the material wall; in time causing wear to plasma facing components. Qualitative models predict that the parallel currents, driven by the divertor sheath, have a direct impact on this radial velocity. In this work, the predictions for radial velocity of plasma filaments in the SOL from models are tested against data from the MAST tokamak and simulation. We apply a statistical method of window averaging to MAST Langmuir probe data in order to examine the scaling of the radial velocity of filaments with the plasma density inside the filaments. Our analysis strongly suggests that the radial dynamics emerge from the competition of multiple mechanisms and not from a single process. At intermediate distances from the bulk plasma, a new model proposed here, in which the parallel current depends on a constant target density appears to be the most relevant for the MAST plasma. This is confirmed using a TOKAM2D simulation with a modified parallel current term.

Finite mean-free-path effects in tokamak scrape-off layers

International Nuclear Information System (INIS)

Cohen, R.H.; Rognlien, T.D.; Xu, X.Q.; Bernstein, I.B.; Chen, Q.

1993-01-01

When the electron mean free path (mfp) becomes bigger than about 1/10 of the parallel electron-temperature gradient scale length, it is well-known that departures from the Spitzer thermal conductivity become important. These departures are commonly modeled by limiting the parallel heat flux q parallel to an empirically determined fraction of nT e v te where v te is the electron thermal speed. The use of flux limit expressions in 2-D scrape-off layer (SOL) modeling codes leads to the qualitatively correct result that the electron temperature drops along a field line as heat is leaked by radial transport, but perhaps for the wrong reasons. In particular the flux-limiting form is demonstratably incorrect in the long-mfp limit. Here the authors re-examine this issue. Recognizing that the heat flux is carried by superthermal electrons, they formulate a linearized 3-D Fokker-Planck problem. They depart from previous treatments by noting that, for typical SOL parameters, the superthermal particles classically carrying the bulk of the heat flux have long mean free paths and are in the loss cone, and so are absent from the distribution function. They argue that this is a key feature which will reduce the heat flux below that calculated previously. They outline several strategies for reducing the Fokker-Planck equation to analytically tractable and/or computationally more tractable forms. In particular, they discuss a diffusion model for the isotropic part of the distribution function, its numerical implementation, and limits in which approximate analytic solutions can be obtained. They also present a heuristic model for the heat flux that accounts for the physical effects discussed above and which has the correct asymptotic limits for small and large mean free path. They compare this model and preliminary analytic and numerical results from the diffusion model with Monte Carlo simulations

Convergence of statistical moments of particle density time series in scrape-off layer plasmas

Energy Technology Data Exchange (ETDEWEB)

Kube, R., E-mail: ralph.kube@uit.no; Garcia, O. E. [Department of Physics and Technology, UiT - The Arctic University of Norway, N-9037 Tromsø (Norway)

2015-01-15

Particle density fluctuations in the scrape-off layer of magnetically confined plasmas, as measured by gas-puff imaging or Langmuir probes, are modeled as the realization of a stochastic process in which a superposition of pulses with a fixed shape, an exponential distribution of waiting times, and amplitudes represents the radial motion of blob-like structures. With an analytic formulation of the process at hand, we derive expressions for the mean squared error on estimators of sample mean and sample variance as a function of sample length, sampling frequency, and the parameters of the stochastic process. Employing that the probability distribution function of a particularly relevant stochastic process is given by the gamma distribution, we derive estimators for sample skewness and kurtosis and expressions for the mean squared error on these estimators. Numerically, generated synthetic time series are used to verify the proposed estimators, the sample length dependency of their mean squared errors, and their performance. We find that estimators for sample skewness and kurtosis based on the gamma distribution are more precise and more accurate than common estimators based on the method of moments.

Effect of chaos on plasma filament dynamics and turbulence in the scrape-off layer

International Nuclear Information System (INIS)

Meyerson, D.; Waelbroeck, F.; Horton, W.; Michoski, C.

2014-01-01

Naturally occurring error fields as well as resonant magnetic perturbations applied for stability control are known to cause magnetic field-line chaos in the scrape-off layer (SOL) region of tokamaks. Here, 2D simulations with the BOUT++ simulation framework are used to investigate the effect of the field-line chaos on the SOL and in particular on its width and peak particle flux. The chaos enters the SOL dynamics only through the connection length, which is evaluated using a Poincaré map. The variation of experimentally relevant quantities, such as the SOL gradient length scale and the intermittency of the particle flux in the SOL, is described as a function of the strength of the magnetic perturbation. It is found that the effect of the chaos is to broaden the profile of the sheath-loss coefficient, which is proportional to the inverse connection length. That is, the SOL transport in a chaotic field is equivalent to that in a model where the sheath-loss coefficient is replaced by its average over the unperturbed flux surfaces. The model does not include the effects of chaotic features other than the parallel connection length

Convergence of statistical moments of particle density time series in scrape-off layer plasmas

International Nuclear Information System (INIS)

Kube, R.; Garcia, O. E.

2015-01-01

Particle density fluctuations in the scrape-off layer of magnetically confined plasmas, as measured by gas-puff imaging or Langmuir probes, are modeled as the realization of a stochastic process in which a superposition of pulses with a fixed shape, an exponential distribution of waiting times, and amplitudes represents the radial motion of blob-like structures. With an analytic formulation of the process at hand, we derive expressions for the mean squared error on estimators of sample mean and sample variance as a function of sample length, sampling frequency, and the parameters of the stochastic process. Employing that the probability distribution function of a particularly relevant stochastic process is given by the gamma distribution, we derive estimators for sample skewness and kurtosis and expressions for the mean squared error on these estimators. Numerically, generated synthetic time series are used to verify the proposed estimators, the sample length dependency of their mean squared errors, and their performance. We find that estimators for sample skewness and kurtosis based on the gamma distribution are more precise and more accurate than common estimators based on the method of moments

In-situ observation of the chemical erosion of graphite in the scrape-off-layer of TEXTOR

International Nuclear Information System (INIS)

Philipps, V.; Vietzke, E.; Erdweg, M.

1989-01-01

A sniffer probe system has been used to investigate the chemical erosion during interaction of the TEXTOR scrape-off plasma with a pyrolytic graphite plate at temperatures up to 1400 0 C. Floating potential conditions as well as 200 V bias has been applied at plasma ion fluxes of about 10 18 ions/cm 2 sec. Methane formation was found to be 8x10 -3 CH 4 /H and 1.5x10 -2 CD 4 /D + for room temperature graphite and floating potential increasing by a factor of two at temperature around 500 0 C. Biasing the graphite decreases the methane yield at room temperature and increase it in the maximum temperature range. CO formation due to chemical interaction of oxygen ions with the graphite reaches ratios between 3 and 6x10 -2 CO/D(H) near the limiter edge under normal TEXTOR scrape-off conditions and exceeds the chemical hydro-(deutero-)carbon formation significantly. The results are discussed in view of the present status of hydro-(deutero-)carbon formation on graphite and carbon impurity observations made in fusion experiments. (orig.)

Interpretive modelling of scrape-off plasmas on the MAST tokamak

Energy Technology Data Exchange (ETDEWEB)

Harrison, J. [Euratom/UKAEA Fusion Association, Culham Science Centre, D2/2.01 Fusion Association, Abingdon, Oxfordshire OX14 3DB (United Kingdom); University of York, Heslington, York (United Kingdom)], E-mail: james.harrison@ukaea.org.uk; Lisgo, S. [Euratom/UKAEA Fusion Association, Culham Science Centre, D2/2.01 Fusion Association, Abingdon, Oxfordshire OX14 3DB (United Kingdom); Counsell, G.F. [Fusion for Energy, Barcelona (Spain); Gibson, K. [University of York, Heslington, York (United Kingdom); Dowling, J. [Euratom/UKAEA Fusion Association, Culham Science Centre, D2/2.01 Fusion Association, Abingdon, Oxfordshire OX14 3DB (United Kingdom); Trojan, L. [University of Manchester, Oxford Road, Manchester (United Kingdom); Reiter, D. [IPP, Forschungszentrum Juelich GmbH, EURATOM Association, D-52425 Juelich (Germany)

2009-06-15

Electrical currents in the scrape-off layer (SOL) of MAST are modelled using an interpretive Onion-Skin Model (OSM) constrained with experimental data from MAST diagnostics. The model was extended to include the effects of the magnetic mirror force, which has a strong influence on the particle and momentum balance in spherical tokamaks, such as MAST . These modifications serve to more accurately model the parallel electric fields present in the MAST SOL, which can alter plasma dynamics via the E x B drift. Simulations show that the electrical current at the divertor targets is predominantly thermoelectric, whereas Pfirsch-Schlueter currents have a greater contribution to the total current in the bulk of the SOL plasma.

Experimental/theoretical comparisons of the turbulence in the scrape-off-layers of Alcator C-Mod, DIII-D, and NSTX

International Nuclear Information System (INIS)

Terry, J.L. . E-mail : terry@psfc.mit.edu; Zweben, S.J.; Rudakov, D.L.

2003-01-01

The intermittent turbulent transport in the scrape-off-layers of Alcator C-Mod, DIII-D, and NSTX is studied experimentally. On DIII-D the fluctuations of both density and temperature have strongly non-Gaussian statistics, and events with amplitudes above 10 times the mean level are responsible for large fractions of the net particle and heat transport, indicating the importance of turbulence on the transport. In C-Mod and NSTX the turbulence is imaged with a very high density of spatial measurements. The 2-D structure and dynamics of emission from a localized gas puff are observed, and intermittent features (also sometimes called 'blobs') are typically seen. On DIII-D the turbulence is imaged using BES and similar intermittent features are seen. The dynamics of these intermittent features are discussed. The experimental observations are compared with numerical simulations of edge turbulence. The electromagnetic turbulence in a 3-D geometry is computed using non-linear plasma fluid equations. The wavenumber spectra in the poloidal dimension of the simulations are in reasonable agreement with those of the C-Mod experimental images once the response of the optical system is accounted for. The resistive ballooning mode is the dominant linear instability in the simulations. (author)

Characteristics of the scrape-off layer in DIII-D high-performance negative central magnetic shear discharges

Energy Technology Data Exchange (ETDEWEB)

Lasnier, C.J. [General Atomics, San Diego, CA (United States); Maingi, R. [General Atomics, San Diego, CA (United States); Leonard, A.W. [General Atomics, San Diego, CA (United States); Allen, S.L. [General Atomics, San Diego, CA (United States); Buchenauer, D.A. [General Atomics, San Diego, CA (United States); Burrell, K.H. [General Atomics, San Diego, CA (United States); Casper, T.A. [General Atomics, San Diego, CA (United States); Cuthbertson, J.W. [General Atomics, San Diego, CA (United States); Fenstermacher, M.E. [General Atomics, San Diego, CA (United States); Hill, D.N. [General Atomics, San Diego, CA (United States); Jong, R.A. [General Atomics, San Diego, CA (United States); Lao, L.L. [General Atomics, San Diego, CA (United States); Lazarus, E.A. [General Atomics, San Diego, CA (United States); Moyer, R.A. [General Atomics, San Diego, CA (United States); Petrie, T.W. [General Atomics, San Diego, CA (United States); Porter, G.D. [General Atomics, San Diego, CA (United States); Rice, B.W. [General Atomics, San Diego, CA (United States); Stallard, B.W. [General Atomics, San Diego, CA (United States); Taylor, T.S. [General Atomics, San Diego, CA (United States); Watkins, J.G. [General Atomics, San Diego, CA (United States)

1997-02-01

In this paper we present measurements of the global power and particle balance in the high-performance phase of negative central magnetic shear (NCS) discharges and compare with reference VH-mode discharges. The principal differences observed are that NCS has a much lower fraction of the total input power flowing into the boundary, less core radiation, and larger rate of stored energy increase as a fraction of total power. Scrape-off layer (SOL) temperature and divertor heat flux profiles, and radiation profiles at the midplane, are similar to VH-mode. Due to the good core particle confinement and efficient fueling by neutral beam injection (NBI), with little gas puffing, the gas load on the walls and the recycling are very low during the NCS discharges. This results in a rate of density rise relative to beam fueling at the L to H transition time which is 1/3 of the value for VH transitions, which is in turn 1/2 that for L-to-ELMing-H-mode transitions. (orig.).

A monte carlo simulation model for the steady-state plasma in the scrape-off layer

International Nuclear Information System (INIS)

Wang, W.X.; Okamoto, M.; Nakajima, N.; Murakami, S.; Ohyabu, N.

1995-12-01

A new Monte Carlo simulation model for the scrape-off layer (SOL) plasma is proposed to investigate a feasibility of so-called 'high temperature divertor operation'. In the model, Coulomb collision effect is accurately described by a nonlinear Monte Carlo collision operator; a conductive heat flux into the SOL is effectively modelled via randomly exchanging the source particles and SOL particles; secondary electrons are included. The steady state of the SOL plasma, which satisfies particle and energy balances and the neutrality constraint, is determined in terms of total particle and heat fluxes across the separatrix, the edge plasma temperature, the secondary electron emission rate, and the SOL size. The model gives gross features of the SOL such as plasma temperatures and densities, the total sheath potential drop, and the sheath energy transmission factor. The simulations are performed for collisional SOL plasma to confirm the validity of the proposed model. It is found that the potential drop and the electron energy transmission factor are in close agreement with theoretical predictions. The present model can provide primarily useful information for collisionless SOL plasma which is difficult to be understood analytically. (author)

Heat flux distribution on an optimised limiter surface and structure of the scrape-off-layer

International Nuclear Information System (INIS)

Denner, T.

1998-12-01

The heat load on plasma-facing components is a key issue for forthcoming fusion experiments. In this work the heat flux on the pump limiter in TEXTOR-94 is measured by a newly developed digital thermography system and these results are compared with theoretical models. The limiter is shaped in such a way as to keep the heat load of the plasma-wetted area low; this is achieved by reducing the angle of incidence of the magnetic field lines with respect to the limiter surface to less than 1 for the first 10 mm of the scrape-off-layer (SOL). This small angle of incidence enhances all effects of toroidal non-uniformity as given e.g. by the magnetic field ripple. Extensive modelling explains well the observed heating pattern on the limiter surface due to the ripple effect. In contrast to expectations from density and temperature distributions in the SOL and at the edge of the confined region, an excessive power density is deposited on the first few millimetres near the roof tip of the limiter. Physical effects which could cause this phenomenon are discussed. (orig.)

Density profiles in the Scrape-Off Layer interpreted through filament dynamics

Science.gov (United States)

Militello, Fulvio

2017-10-01

We developed a new theoretical framework to clarify the relation between radial Scrape-Off Layer density profiles and the fluctuations that generate them. The framework provides an interpretation of the experimental features of the profiles and of the turbulence statistics on the basis of simple properties of the filaments, such as their radial motion and their draining towards the divertor. L-mode and inter-ELM filaments are described as a Poisson process in which each event is independent and modelled with a wave function of amplitude and width statistically distributed according to experimental observations and evolving according to fluid equations. We will rigorously show that radially accelerating filaments, less efficient parallel exhaust and also a statistical distribution of their radial velocity can contribute to induce flatter profiles in the far SOL and therefore enhance plasma-wall interactions. A quite general result of our analysis is the resiliency of this non-exponential nature of the profiles and the increase of the relative fluctuation amplitude towards the wall, as experimentally observed. According to the framework, profile broadening at high fueling rates can be caused by interactions with neutrals (e.g. charge exchange) in the divertor or by a significant radial acceleration of the filaments. The framework assumptions were tested with 3D numerical simulations of seeded SOL filaments based on a two fluid model. In particular, filaments interact through the electrostatic field they generate only when they are in close proximity (separation comparable to their width in the drift plane), thus justifying our independence hypothesis. In addition, we will discuss how isolated filament motion responds to variations in the plasma conditions, and specifically divertor conditions. Finally, using the theoretical framework we will reproduce and interpret experimental results obtained on JET, MAST and HL-2A.

Reduction of the turbulent blob transport in the scrape-off layer by a resonant magnetic perturbation in TEXTOR

International Nuclear Information System (INIS)

Xu, Y.; Weynants, R.R.; Van Schoor, M.; Vergote, M.; Jachmich, S.; Jakubowski, M.W.; Mitri, M.; Schmitz, O.; Unterberg, B.; Reiser, D.; Finken, K.H.; Lehnen, M.; Beyer, P.

2009-01-01

During the static 6/2 Dynamic Ergodic Divertor experiments in TEXTOR, a significant influence of the edge resonant magnetic perturbation (RMP) on the turbulent blob transport in the scrape-off layer (SOL) has been observed. In ohmic discharges without the RMP, the blobs extend 4-5 cm deep into the SOL with a radially outward moving speed of about 1 km s -1 and hence constitute a strong outflow of mass. With the application of the RMP, the blob amplitudes and their radially moving velocity are both reduced, resulting in a significant reduction of the blob transport in the SOL. The reduction effect of the RMP on blobs is found to be robust to changes in the operational regime and to phasing variations of the RMP as well. The blob dynamics appears to be consistent with the paradigm of the radial motions of the blob structures driven by the interchange instability.

Heuristic drift-based model of the power scrape-off width in low-gas-puff H-mode tokamaks

International Nuclear Information System (INIS)

Goldston, R.J.

2012-01-01

A heuristic model for the plasma scrape-off width in low-gas-puff tokamak H-mode plasmas is introduced. Grad B and curv B drifts into the scrape-off layer (SOL) are balanced against near-sonic parallel flows out of the SOL, to the divertor plates. The overall particle flow pattern posited is a modification for open field lines of Pfirsch–Schlüter flows to include order-unity sinks to the divertors. These assumptions result in an estimated SOL width of ∼2aρ p /R. They also result in a first-principles calculation of the particle confinement time of H-mode plasmas, qualitatively consistent with experimental observations. It is next assumed that anomalous perpendicular electron thermal diffusivity is the dominant source of heat flux across the separatrix, investing the SOL width, derived above, with heat from the main plasma. The separatrix temperature is calculated based on a two-point model balancing power input to the SOL with Spitzer–Härm parallel thermal conduction losses to the divertor. This results in a heuristic closed-form prediction for the power scrape-off width that is in reasonable quantitative agreement both in absolute magnitude and in scaling with recent experimental data. Further work should include full numerical calculations, including all magnetic and electric drifts, as well as more thorough comparison with experimental data.

Selected methods of electron-and ion-diagnostics in tokamak scrape-off-layer

Directory of Open Access Journals (Sweden)

Sadowski Marek J.

2015-06-01

Full Text Available This invited paper considers reasons why exact measurements of fast electron and ion losses in tokamaks, and particularly i n a scrape-off-layer and near a divertor region, are necessary in order to master nuclear fusion energy production. Attention is also paid to direct measurements of escaping fusion products from D-D and D-T reactions, and in particular of fast alphas which might be used for plasma heating. The second part describes the generation of so-called runaway and ripple-born electrons which might induce high energy losses and cause severe damages of internal walls in fusion facilities. Advantages and disadvantages of different diagnostic methods applied for studies of such fast electrons are discussed. Particular attention is paid to development of a direct measuring technique based on the Cherenkov effect which might be induced by fast electrons in appropriate radiators. There are presented various versions of Cherenkov-type probes which have been developed by the NCBJ team and applied in different tokamak experiments. The third part is devoted to direct measurements of fast ions (including those produced by the nuclear fusion reactions which can escape from a high-temperature plasma region. Investigation of fast fusion-produced protons from tokamak discharges is reported. New ion probes, which were developed by the NCBJ team, are also presented. For the first time there is given a detailed description of an ion pinhole camera, which enables irradiation of several nuclear track detectors during a single tokamak discharge, and a miniature Thomson-type mass-spectrometer, which can be used for ion measurements at plasma borders.

Scrape-off profiles and effects of limiter pumping in Tore Supra

International Nuclear Information System (INIS)

Budny, R.

1986-11-01

A one dimensional plasma scrape-off model was used to simulate Tore Supra discharges which are limited by various combinations of the pumped and inner limiters. Scrape-off profiles of the electron density and temperature, ion temperature, and neutral density are given. For each case, various fractions of the ion flux to the neutralizers were assumed to be pumped. Modifications of the scrap-off profiles caused by pumping are predicted. Pumping efficiencies are calculated including the effects of flux amplification caused by recycling. The pumping efficiency is estimated to be 8% for low-power discharges formed on the outer pumped limiter, 7.5% for intermediate-power discharges formed on the seven-module pumped-limiter system, and 5% for full-power discharges formed on both the inner limiter and the pumped-limiter system. The maximum particle removal rate is estimated to be 150 Tl/s

Dual wavelength imaging of a scrape-off layer in an advanced beam-driven field-reversed configuration

Energy Technology Data Exchange (ETDEWEB)

Osin, D.; Schindler, T., E-mail: dosin@trialphaenergy.com [Tri Alpha Energy, Inc., P.O. Box 7010, Rancho Santa Margarita, California 92688-7010 (United States)

2016-11-15

A dual wavelength imaging system has been developed and installed on C-2U to capture 2D images of a He jet in the Scrape-Off Layer (SOL) of an advanced beam-driven Field-Reversed Configuration (FRC) plasma. The system was designed to optically split two identical images and pass them through 1 nm FWHM filters. Dual wavelength images are focused adjacent on a large format CCD chip and recorded simultaneously with a time resolution down to 10 μs using a gated micro-channel plate. The relatively compact optical system images a 10 cm plasma region with a spatial resolution of 0.2 cm and can be used in a harsh environment with high electro-magnetic noise and high magnetic field. The dual wavelength imaging system provides 2D images of either electron density or temperature by observing spectral line pairs emitted by He jet atoms in the SOL. A large field of view, combined with good space and time resolution of the imaging system, allows visualization of macro-flows in the SOL. First 2D images of the electron density and temperature observed in the SOL of the C-2U FRC are presented.

The effect of ion drifts on the properties of the tokamak scrape-off plasma

International Nuclear Information System (INIS)

Petravic, M.; Kuo-Petravic, G.

1988-09-01

A plasma fluid model which takes into account ion drifts has been constructed and applied to the scrape-off layer of a tokamak with a poloidal divertor. This model predicts near-sonic toroidal velocities and large poloidal flows in most of the scrapeoff together with steep gradients in the pressure and electrostatic potential along the magnetic field near the X-point, contrary to the predictions of the standard model. The potential step at X-point should reduce parallel heat transport and could act as an H-mode trigger. 12 refs., 4 figs

Plasma particle sources due to interactions with neutrals in a turbulent scrape-off layer of a toroidally confined plasma

DEFF Research Database (Denmark)

Thrysøe, Alexander Simon; Løiten, M.; Madsen, J.

2018-01-01

The conditions in the edge and scrape-off layer (SOL) of magnetically confined plasmas determine the overall performance of the device, and it is of great importance to study and understand the mechanics that drive transport in those regions. If a significant amount of neutral molecules and atoms...... is present in the edge and SOL regions, those will influence the plasma parameters and thus the plasma confinement. In this paper, it is displayed how neutrals, described by a fluid model, introduce source terms in a plasma drift-fluid model due to inelastic collisions. The resulting source terms...... are included in a four-field drift fluid model, and it is shown how an increasing neutral particle density in the edge and SOL regions influences the plasma particle transport across the lastclosed-flux-surface. It is found that an appropriate gas puffing rate allows for the edge density in the simulation...

Fast electron flux driven by lower hybrid wave in the scrape-off layer

International Nuclear Information System (INIS)

Li, Y. L.; Xu, G. S.; Wang, H. Q.; Wan, B. N.; Chen, R.; Wang, L.; Gan, K. F.; Yang, J. H.; Zhang, X. J.; Liu, S. C.; Li, M. H.; Ding, S.; Yan, N.; Zhang, W.; Hu, G. H.; Liu, Y. L.; Shao, L. M.; Li, J.; Chen, L.; Zhao, N.

2015-01-01

The fast electron flux driven by Lower Hybrid Wave (LHW) in the scrape-off layer (SOL) in EAST is analyzed both theoretically and experimentally. The five bright belts flowing along the magnetic field lines in the SOL and hot spots at LHW guard limiters observed by charge coupled device and infrared cameras are attributed to the fast electron flux, which is directly measured by retarding field analyzers (RFA). The current carried by the fast electron flux, ranging from 400 to 6000 A/m 2 and in the direction opposite to the plasma current, is scanned along the radial direction from the limiter surface to the position about 25 mm beyond the limiter. The measured fast electron flux is attributed to the high parallel wave refractive index n || components of LHW. According to the antenna structure and the LHW power absorbed by plasma, a broad parallel electric field spectrum of incident wave from the antennas is estimated. The radial distribution of LHW-driven current density is analyzed in SOL based on Landau damping of the LHW. The analytical results support the RFA measurements, showing a certain level of consistency. In addition, the deposition profile of the LHW power density in SOL is also calculated utilizing this simple model. This study provides some fundamental insight into the heating and current drive effects induced by LHW in SOL, and should also help to interpret the observations and related numerical analyses of the behaviors of bright belts and hot spots induced by LHW

A two-dimensional statistical framework connecting thermodynamic profiles with filaments in the scrape off layer and application to experiments

Science.gov (United States)

Militello, F.; Farley, T.; Mukhi, K.; Walkden, N.; Omotani, J. T.

2018-05-01

A statistical framework was introduced in Militello and Omotani [Nucl. Fusion 56, 104004 (2016)] to correlate the dynamics and statistics of L-mode and inter-ELM plasma filaments with the radial profiles of thermodynamic quantities they generate in the Scrape Off Layer. This paper extends the framework to cases in which the filaments are emitted from the separatrix at different toroidal positions and with a finite toroidal velocity. It is found that the toroidal velocity does not affect the profiles, while the toroidal distribution of filament emission renormalises the waiting time between two events. Experimental data collected by visual camera imaging are used to evaluate the statistics of the fluctuations, to inform the choice of the probability distribution functions used in the application of the framework. It is found that the toroidal separation of the filaments is exponentially distributed, thus suggesting the lack of a toroidal modal structure. Finally, using these measurements, the framework is applied to an experimental case and good agreement is found.

Plasma particle sources due to interactions with neutrals in a turbulent scrape-off layer of a toroidally confined plasma

Science.gov (United States)

Thrysøe, A. S.; Løiten, M.; Madsen, J.; Naulin, V.; Nielsen, A. H.; Rasmussen, J. Juul

2018-03-01

The conditions in the edge and scrape-off layer (SOL) of magnetically confined plasmas determine the overall performance of the device, and it is of great importance to study and understand the mechanics that drive transport in those regions. If a significant amount of neutral molecules and atoms is present in the edge and SOL regions, those will influence the plasma parameters and thus the plasma confinement. In this paper, it is displayed how neutrals, described by a fluid model, introduce source terms in a plasma drift-fluid model due to inelastic collisions. The resulting source terms are included in a four-field drift-fluid model, and it is shown how an increasing neutral particle density in the edge and SOL regions influences the plasma particle transport across the last-closed-flux-surface. It is found that an appropriate gas puffing rate allows for the edge density in the simulation to be self-consistently maintained due to ionization of neutrals in the confined region.

Coupled plasma-neutral transport model for the scrape-off region

International Nuclear Information System (INIS)

Galambos, J.D.; Peng, Y.K.M.; Heifetz, D.

1985-03-01

Analysis of the scrape-off region requires treatment of the plasma transport along and across the field lines and inclusion of the neutral transport effects. A method for modeling the scrape-off region that is presented here uses separate models for each of these aspects that are coupled together through an iteration procedure that requires only minimal numerical effort. The method is applied here to estimate the neutral pumping rates in the pump-limiter and divertor options for a proposed deuterium-tritium (D-T) ignition experiment. High neutral recycling in the vicinity of the neutralizer plate dramatically affects pumping rates for both the pump-limiter and divertor. In both cases, the plasma flow into the channel surrounding the neutralizer plate is greatly reduced by the neutral recycling. The fraction of this flow that is pumped can be large (> 50%), but in general it is dependent on the particular geometry and plasma conditions. It is estimated that pumping speeds approximately greater than 10 5 L/s are adequate for the exhaust requirements in the pump-limiter and the divertor cases. Also, high neutral recycling on the front surface of the limiter tends to increase the neutral pumping rate

Spectroscopic determination of inverse photon efficiencies of W atoms in the scrape-off layer of TEXTOR

Science.gov (United States)

Brezinsek, S.; Laengner, M.; Coenen, J. W.; O'Mullane, M. G.; Pospieszczyk, A.; Sergienko, G.; Samm, U.

2017-12-01

Optical emission spectroscopy can be applied to determine in situ tungsten particle fluxes from erosion processes at plasma-facing materials. Inverse photon efficiencies convert photon fluxes of WI and WII line transitions into W and {{{W}}}+ particle fluxes, respectively, dependening on the local plasma conditions. Experiments in TEXTOR were carried out to determine effective conversion factors for different WI and WII transitions with the aid of WF6 injection into deuterium scrape-off layer plasmas in the electron temperature T e range between {T}{e}=20 {eV} and {T}{e}=82 {eV}. The inverse photon efficiencies or so-called effective \\tfrac{S}{{XB}}-values have been determined for WI lines at λ =400.9 {nm}, 429.5 nm, 488.7 nm, 498.3 nm, and 522.5 nm as well as for WII at λ =434.6 {nm} and compared with theoretical calculations from the ADAS data base. Moreover, a multi-machine scaling for the \\tfrac{S}{{XB}}-value in the range of T e between 2...100 {eV} has been determined for the most prominent WI line at λ =400.9 {nm} to \\tfrac{S}{{XB}}({T}{e})=53.63-56.07× {e}(0.045× {T{e}[{eV}])} considering experimental data from TEXTOR, ASDEX Upgrade, PSI and PISCES. Comparison with ADAS calculations for the same transition reveal a good qualitative agreement with the dependence on T e , but an underestimation of ADAS calculations of less than 25% over the full covered range of experimentally accessible T e in the multi-machine scaling. A good agreement within the experimental uncertainties is found between TEXTOR and ADAS \\tfrac{S}{{XB}}-values for WI at λ =429.5 {nm} and λ =488.7 {nm} whereas an underestimation of up to a factor two of ADAS values for WI at λ =522.5 {nm} and λ =498.3 {nm} was measured. Potentially, reasons for the discrepancy are an overestimation of applied ionisation rate coefficients in ADAS for neutral W and a stronger electron dependence n e for these transitions.

Localization of fluctuation measurement by wave scattering close to a cut off layer

International Nuclear Information System (INIS)

Zou, X.L.; Laurent, L.; Rax, J.M.; Lehner, T.

1990-01-01

The diagnostic of plasma fluctuations in tokamaks based on the scattering of an electromagnetic wave close to a cut off layer is investigated. A linear density profile is considered. An one-dimensional exact analysis is performed. Spatial and spectral localization of scattering process close to the cut off layer is studied and a modified Bragg rule is derived. The structure of pump and of scattered waves is analyzed. The diagnostic seems to be local and sensitive for low R fluctuations

A new thermal He-beam diagnostic for electron density and temperature measurements in the scrape-off layer of ASDEX Upgrade

Energy Technology Data Exchange (ETDEWEB)

Griener, Michael; Wolfrum, Elisabeth; Eich, Thomas; Herrmann, Albrecht; Rohde, Volker [Max Planck Institute for Plasma Physics, Garching (Germany); Schmitz, Oliver [Engineering Physics Department, University of Wisconsin-Madison (United States); Stroth, Ulrich [Max Planck Institute for Plasma Physics, Garching (Germany); Physik Department E28, Technische Universitaet Muenchen, Garching (Germany); Collaboration: the ASDEX Upgrade Team

2015-05-01

In a nuclear fusion device power is exhausted across the last closed flux surface into the so-called 'scrape-off layer', SOL. In order to study the transport dynamics to (a) the divertor via parallel heat flux and (b) to the wall via filaments, a diagnostic for the determination of n{sub e} and T{sub e} with high spatial and temporal resolution is required. Although the diagnostic capabilities of the ASDEX Upgrade edge plasma are excellent, there is a lack of spatially and temporally highly resolved electron temperature measurements in the SOL. Therefore a piezo valve will be installed in ASDEX Upgrade in April 2015. It allows fast chopping of a thermal He-beam which is part of the new diagnostic. In the first campaign, existing lines of sight of the CXRS diagnostic will be used to measure various He I transitions to confirm the collisional radiative model for He. The principle of the thermal He-diagnostic as well as calculations of the achievable spatial resolution of the initial set-up are presented.

Ion temperature measurements in the scrape-off layer of the Tore Supra Tokamak

International Nuclear Information System (INIS)

Kocan, M.

2009-10-01

The thesis describes measurements of the scrape-off layer (SOL) ion temperature T i with a retarding field analyzer (RFA) in the limiter tokamak Tore Supra. Considerable emphasis is placed on study of the instrumental effects of RFAs and their influence on T i measurements. In general, the influence of instrumental effects on T i measurements is found to be relatively small. The instrumental study is followed by systematic measurements of T i (as well as other parameters) in the Tore Supra SOL. This includes the scaling of SOL temperatures and electron density with the main plasma parameters (such as the plasma density, toroidal magnetic field, working gas, and the radiated power fraction). Except at very high densities or in detached plasmas, SOL T i is found to be higher than T e by up to a factor of 7. While SOL T i is found to vary by almost two orders of magnitude, following the variation of the core temperatures, SOL T e changes only little and seems to be decoupled from the core plasma. The first continuous T i /T e profile from the edge of the confined plasma into the SOL is constructed using data from different tokamaks. It is shown that T i /T e > 1 in the SOL but also in the confined plasma, and increases with radius. The first evidence of poloidal asymmetry of the radial ion and electron energy transport in the SOL is reported. Implications for ITER start-up phase are discussed. Correlation of the asymmetries of SOL T i and T e measured from both directions along the magnetic field lines with changes of the parallel Mach number is studied. SOL T i was measured for the first time in Tore Supra by charge exchange recombination spectroscopy (CXRS) and compared to RFA data. A factor of 4 higher T i measured by CXRS is a subject of further analysis. (A.C.)

Linear and nonlinear studies of resistive-ballooning modes in a tokamak edge plasma with scrape-off layer

International Nuclear Information System (INIS)

Lau, Y.T.; Novakovskii, S.V.; Drake, J.F.

1996-01-01

We will present 2D linear and 3D nonlinear studies of resistive-ballooning modes in tokamak edge plasmas which include a closed flux region, as well as a limiter scrape-off layer (SOL) region. These studies therefore go beyond most earlier work, where the stability of the edge in the closed flux region and in the SOL have been considered separately. A 2D linear code, 2D-BALLOON, examines the stability of these curvature driven modes and provides the complete 2D eigenfunction spanning the closed flux surface region as well the open field line region. The sheath boundary condition in the SOL introduces an important new parameter λ = (m e /m i ) 1/2 v ei qR/v Te . This parameter plays a significant role in determining the stability of these modes in both the closed flux and SOL regions because of the radial coupling across the last closed flux surface (LCFS). For small λ the spectrum of unstable modes is broad and extends into the low toroidal mode number exclamation point regime where the spatial structure is flute-like. The amplitude for these modes is larger in the SOL compared to the closed flux region. However when A is increased, the low mode numbers are strongly stabilized and the high mode numbers which are strongly ballooning are the dominant modes. In this regime the radial modes straddle the LCFS. In both these cases, the variation in the plasma density is necessary for the radial localization. In the three-dimensional nonlinear simulations, we have solved a set of fluid equations in a toroidal geometry with both the closed flux region and the SOL. The introduction of the SOL to the twisted tube for the closed flux region, has been a major addition to our 3D code. We find that the turbulent transport in the SOL drops significantly as A is increased, which is consistent with our expectations from the 2D linear code results

Transport-driven scrape-off layer flows and the x-point dependence of the L-H power threshold in Alcator C-Moda)

Science.gov (United States)

LaBombard, B.; Rice, J. E.; Hubbard, A. E.; Hughes, J. W.; Greenwald, M.; Granetz, R. S.; Irby, J. H.; Lin, Y.; Lipschultz, B.; Marmar, E. S.; Marr, K.; Mossessian, D.; Parker, R.; Rowan, W.; Smick, N.; Snipes, J. A.; Terry, J. L.; Wolfe, S. M.; Wukitch, S. J.

2005-05-01

Factor of ˜2 higher power thresholds for low- to high-confinement mode transitions (L-H) with unfavorable x-point topologies in Alcator C-Mod [Phys. Plasmas 1, 1511 (1994)] are linked to flow boundary conditions imposed by the scrape-off layer (SOL). Ballooning-like transport drives flow along magnetic field lines from low- to high-field regions with toroidal direction dependent on upper/lower x-point balance; the toroidal rotation of the confined plasma responds, exhibiting a strong counter-current rotation when B ×∇B points away from the x point. Increased auxiliary heating power (rf, no momentum input) leads to an L-H transition at approximately twice the edge electron pressure gradient when B ×∇B points away. As gradients rise prior to the transition, toroidal rotation ramps toward the co-current direction; the H mode is seen when the counter-current rotation imposed by the SOL flow becomes compensated. Remarkably, L-H thresholds in lower-limited discharges are identical to lower x-point discharges; SOL flows are also found similar, suggesting a connection.

Intermittent electron density and temperature fluctuations and associated fluxes in the Alcator C-Mod scrape-off layer

Science.gov (United States)

Kube, R.; Garcia, O. E.; Theodorsen, A.; Brunner, D.; Kuang, A. Q.; LaBombard, B.; Terry, J. L.

2018-06-01

The Alcator C-Mod mirror Langmuir probe system has been used to sample data time series of fluctuating plasma parameters in the outboard mid-plane far scrape-off layer. We present a statistical analysis of one second long time series of electron density, temperature, radial electric drift velocity and the corresponding particle and electron heat fluxes. These are sampled during stationary plasma conditions in an ohmically heated, lower single null diverted discharge. The electron density and temperature are strongly correlated and feature fluctuation statistics similar to the ion saturation current. Both electron density and temperature time series are dominated by intermittent, large-amplitude burst with an exponential distribution of both burst amplitudes and waiting times between them. The characteristic time scale of the large-amplitude bursts is approximately 15 μ {{s}}. Large-amplitude velocity fluctuations feature a slightly faster characteristic time scale and appear at a faster rate than electron density and temperature fluctuations. Describing these time series as a superposition of uncorrelated exponential pulses, we find that probability distribution functions, power spectral densities as well as auto-correlation functions of the data time series agree well with predictions from the stochastic model. The electron particle and heat fluxes present large-amplitude fluctuations. For this low-density plasma, the radial electron heat flux is dominated by convection, that is, correlations of fluctuations in the electron density and radial velocity. Hot and dense blobs contribute only a minute fraction of the total fluctuation driven heat flux.

Ion and electron parameters in the alcator C tokamak scrape-off region

International Nuclear Information System (INIS)

Wan, A.S.H.

1986-05-01

Janus is a bi-directional, multi-functional edge probe used to diagnose the ion and electron parameters in the Alcator C tokamak scrape-off region. Two mirror image sets of diagnostics are aligned to face the electron and ion sides along magnetic field lines. Each set of diagnostics consists of a retarding-field energy analyzer (RFEA), a Langmuir probe, and a calorimeter. The RFEA can alternatively sample both the ion and electron parallel energy distribution functions during a tokamak discharge. From the Langmuir probe, one can infer electron temperature, density, and the plasma floating potential. Simple Langmuir probe theory is found to yield the best agreement between the measured Langmuir probe characteristics and the RFEA-inferred T/sub e/. The calorimeter independently detects the total parallel heat flux incident to an electrically floating plate. The measured sheath transmission coefficient, however, is typically lower than the theoretically predicted value by a factor of approx.3. Together these diagnostics enable detailed, localized edge plasma characterization on Alcator C

Effect of lower hybrid waves on turbulence and transport of particles and energy in the FTU tokamak scrape-off layer plasma

International Nuclear Information System (INIS)

Ridolfini, V Pericoli

2011-01-01

All the main features of the scrape-off layer turbulence, magnitude, frequency spectrum and perpendicular wave vector, ξ t , are strongly affected by the injection of lower hybrid (LH) power into the FTU tokamak. The governing parameters are the local last closed magnetic surface values of density, n e,LCMS , and temperature, T e,LCMS . n e,LCMS determines the perpendicular wave vector of the LH waves, which is a key parameter for the multiple scattering processes, and together with T e,LCMS the collisionality that exerts a stabilizing effect on the fluctuations. This effect, still to be examined in the light of theoretical models, leads to an asymptotic value for the fluctuation relative amplitude in the ohmic phase close to 25%, and ∼10% in the LH phase, or even less, since the saturation level is not yet attained. The LH waves also can strongly raise ξ t , about 3 times, and double the root mean square frequency. The transfer of momentum and energy in the mutual scattering of LH and turbulence 'waves' drives these changes. An increase also of the cross-correlation between temperature and electric potential fluctuations should occur in order to explain the magnitude of the fluctuation amplitude drop and the large increment of the temperature e-folding decay, by more than a factor of 2.5. Particle transport, however, does not appear to be affected to a large extent-the density e-folding decay length is almost unchanged but the power flow typical length rises by about a factor of 1.5, which is a relevant figure in view of the problem of mitigating the power loads on divertor targets in future reactors. These changes are confined mainly within the flux tube connected with the LH waves launching antenna, but start to spread significantly out of it at high plasma densities.

Techniques For Injection Of Pre-Charaterized Dust Into The Scrape Off Layer Of Fusion Plasma

International Nuclear Information System (INIS)

Roquemore, A.L.; John, B.; Friesen, F.; Hartzfeld, K.; Mansfield, D.K.

2011-01-01

Introduction of micron-sized dust into the scrape-off layer (SOL) of a plasma has recently found many applications aimed primarily at determining dust behavior in future fusion reactors. The dust particles are typically composed of materials intrinsic to a fusion reactor. On DIII-D and TEXTOR carbon dust has been introduced into the SOL using a probe inserted from below into the divertor region. On NSTX, both Li and tungsten dust have been dropped from the top of the machine into the SOL throughout the duration of a discharge, by utilizing a vibrating piezoelectric based particle dropper. The original particle dropper was developed to inject passivated Li powder ∼ 40 μm in diameter into the SOL to enhance plasma performance. A simplified version of the dropper was developed to introduce trace amounts of tungsten powder for only a few discharges, thus not requiring a large powder reservoir. The particles emit visible light from plasma interactions and can be tracked by either spectroscopic means or by fast frame rate visible cameras. This data can then be compared with dust transport codes such as DUSTT to make predictions of dust behavior in next-step devices such as ITER. For complete modeling results, it is desired to be able to inject pre-characterized dust particles in the SOL at various known poloidal locations, including near the vessel midplane. Purely mechanical methods of injecting particles are presently being studied using a modified piezoelectric-based powder dropper as a particle source and one of several piezo-based transducers to deflect the particles into the SOL. Vibrating piezo fans operating at 60 Hz with a deflection of ±2.5 cm can impart a significant horizontal boost in velocity. The highest injection velocities are expected from rotating paddle wheels capable of injecting particles at 10's of meters per second depending primarily on the rotation velocity and diameter of the wheel. Several injection concepts have been tested and will be

Status of the new thermal He-beam diagnostic for electron density and temperature measurements in the scrape-off layer of ASDEX upgrade

Energy Technology Data Exchange (ETDEWEB)

Griener, Michael; Stroth, Ulrich [Max Planck Institute for Plasma Physics, Boltzmannstr. 2, 85748 Garching (Germany); Physik Department E28, Technische Universitaet Muenchen, 85748 Garching (Germany); Wolfrum, Elisabeth; Eich, Thomas; Herrmann, Albrecht; Rohde, Volker [Max Planck Institute for Plasma Physics, Boltzmannstr. 2, 85748 Garching (Germany); Schmitz, Oliver [Engineering Physics Department, University of Wisconsin-Madison (United States); Collaboration: the ASDEX Upgrade Team

2016-07-01

In a nuclear fusion device a significant fraction of power is exhausted across the last closed flux surface into the so-called ''scrape-off layer''. In order to study the transport dynamics to (a) the divertor via parallel heat flux and (b) to the wall via filaments, a diagnostic for the determination of n{sub e} and T{sub e} with high spatial and temporal resolution is required. These data should be provided by the new thermal He-beam diagnostic, where helium is injected into the plasma by a piezo valve. The principle of this diagnostic is the measurement of line resolved emission intensities of the excited helium. The calculated line intensity ratios of two singlet lines combined with a collisional radiative model then lead to n{sub e} values, whereas singlet-triplet ratios yield T{sub e} values. The principle of the He-diagnostic as well as emission profiles of several He I transitions measured during the campaign 2015/2016 will be shown. First calculated n{sub e} and T{sub e} profiles will be compared to data from the lithium beam and the Thomson scattering diagnostic.

A comparison of mid-plane scrape-off-layer measurements with model predictions in MAST and the calculation of cross-field transport coefficients

International Nuclear Information System (INIS)

Kirk, A; Counsell, G F; Fundamenski, W; Ahn, J-W; Taylor, D; Walsh, M J; Yang, Y

2004-01-01

The outboard mid-plane values of electron density (n e ) and temperature (T e ) in the scrape-off-layer (SOL) of MAST are derived from target Langmuir probe measurements using OSM2-EIRENE and also using a simple two-point model. The values are compared with mid-plane measurements of n e and T e from a reciprocating probe and a Thomson scattering system for Ohmic, L- and H-modes single-null divertor (SND) discharges. The cross-field heat (χ perpendicular ) diffusion coefficient at the low field side of SND discharges is derived both using the OSM2-EIRENE model and a two-point model coupled with a simple theory. The results are found to be similar within the errors. Typically χ perpendicular values are found to lie in the range 0.5-2.0 m 2 s -1 for L-mode and 0.1-0.5 m 2 s -1 for H-mode. A comparison is made of the transport coefficients derived at the low and high field sides for a set of connected double-null discharges. These results are used to make preliminary observations of the effect of magnetic fields on SOL transport in MAST

Three-dimensional simulations of plasma turbulence in the RFX-mod scrape-off layer and comparison with experimental measurements

Science.gov (United States)

Riva, Fabio; Vianello, Nicola; Spolaore, Monica; Ricci, Paolo; Cavazzana, Roberto; Marrelli, Lionello; Spagnolo, Silvia

2018-02-01

The tokamak scrape-off layer (SOL) plasma dynamics is investigated in a circular limiter configuration with a low edge safety factor. Focusing on the experimental parameters of two ohmic tokamak inner-wall limited plasma discharges in RFX-mod [Sonato et al., Fusion Eng. Des. 74, 97 (2005)], nonlinear SOL plasma simulations are performed with the GBS code [Ricci et al., Plasma Phys. Controlled Fusion 54, 124047 (2012)]. The numerical results are compared with the experimental measurements, assessing the reliability of the GBS model in describing the RFX-mod SOL plasma dynamics. It is found that the simulations are able to quantitatively reproduce the RFX-mod experimental measurements of the electron plasma density, electron temperature, and ion saturation current density (jsat) equilibrium profiles. Moreover, there are indications that the turbulent transport is driven by the same instability in the simulations and in the experiment, with coherent structures having similar statistical properties. On the other hand, it is found that the simulation results are not able to correctly reproduce the floating potential equilibrium profile and the jsat fluctuation level. It is likely that these discrepancies are, at least in part, related to simulating only the tokamak SOL region, without including the plasma dynamics inside the last close flux surface, and to the limits of applicability of the drift approximation. The turbulence drive is then identified from the nonlinear simulations and with the linear theory. It results that the inertial drift wave is the instability driving most of the turbulent transport in the considered discharges.

Drifts, currents, and power scrape-off width in SOLPS-ITER modeling of DIII-D

International Nuclear Information System (INIS)

Meier, E. T.; Goldston, R. J.; Kaveeva, E. G.; Makowski, M. A.; Mordijck, S.

2016-01-01

The effects of drifts and associated flows and currents on the width of the parallel heat flux channel (λ q ) in the tokamak scrape-off layer (SOL) are analyzed using the SOLPS-ITER 2D fluid transport code. Motivation is supplied by Goldston’s heuristic drift (HD) model for λ q , which yields the same approximately inverse poloidal magnetic field dependence seen in multi-machine regression. The analysis, focusing on a DIII-D H-mode discharge, reveals HD-like features, including comparable density and temperature fall-off lengths in the SOL, and up-down ion pressure asymmetry that allows net cross-separatrix ion magnetic drift flux to exceed net anomalous ion flux. In experimentally relevant high-recycling cases, scans of both toroidal and poloidal magnetic field (B tor and B pol ) are conducted, showing minimal λ q dependence on either component of the field. Insensitivity to B tor is expected, and suggests that SOLPS-ITER is effectively capturing some aspects of HD physics. Absence of λ q dependence on B pol , however, is inconsistent with both the HD model and experimental results. As a result, the inconsistency is attributed to strong variation in the parallel Mach number, which violates one of the premises of the HD model.

Plasma confinement modification and convective transport suppression in the scrape-off layer using additional gas puffing in the STOR-M tokamak

International Nuclear Information System (INIS)

Dreval, M; Hubeny, M; Ding, Y; Onchi, T; Liu, Y; Hthu, K; Elgriw, S; Xiao, C; Hirose, A

2013-01-01

The influence of short gas puffing (GP) pulses on the scrape-off layer (SOL) transport is studied. Similar responses of ion saturation current and floating potential measured near the GP injection valve and in the 90° toroidally separated cross-section suggest that the GP influence on the SOL region should be global. A drop in plasma temperature and a decrease in the rotational velocity of the plasma are observed in the SOL region immediately after the GP pulse; however, an unexpected increase in electron and ion temperatures is observed in the second stage of the plasma response. The decrease in floating potential fluctuations indicates that the turbulent transport is dumped immediately after the GP pulse. The GP-induced modification of turbulence properties in the SOL points to a convective transport suppression in the STOR-M tokamak. A substantial decrease in the skewness and kurtosis of ion saturation current fluctuations is observed in the SOL region resulting in the probability distribution function (PDF) getting closer to the Gaussian distribution. The plasma potential reduction, the change in plasma rotation and the suppression of turbulent transport in the SOL region indicate that the plasma confinement is modified after the GP injection. Some features of the H-mode-like confinement in the plasma bulk also accompany the SOL observations after application of the additional sharp GP pulse. (paper)

Retention of neon in graphite after ion beam implantation or exposures to the scrape-off layer plasma in the TEXTOR tokamak

International Nuclear Information System (INIS)

Kim, Y.M.; Philipps, V.; Rubel, M.; Vietzke, E.; Pospieszczyk, A.; Unterberg, B.; Jaspers, R.

2002-01-01

The interaction of neon ions with graphite was investigated for targets either irradiated with ion beams (2-10 keV range) or exposed to the scrape-off layer plasma in the TEXTOR tokamak during discharges with neon edge cooling. The emphasis was on the influence of the target temperature (300-1200 K) and the implantation dose on the neon retention and reemission. The influence of deuterium impact on the retention of neon implanted into graphite has also been addressed. In ion beam experiments saturation is observed above a certain ion dose with a saturation level, which decreases with increasing target temperature. The temperature dependence of the thermal desorption corresponds to an apparent binding energy of about 2.06 eV. The retention of neon (C Ne /C C ) decreases with increasing ion energy with values from 0.55 to 0.15 following irradiation with 2 and 10 keV ions, respectively. The reemission yield during the irradiation increases with target temperature and above 1200 K all impinging ions are reemitted instantaneously. The retention densities measured using the sniffer probe at the TEXTOR tokamak are less than 1% of the total neon fluence and are over one order of magnitude smaller than those observed in ion beam experiments. The results are discussed in terms of different process decisive for ion deposition and release under the two experimental conditions

Drift-based Model for Power Scrape-off Width in Low-Gas-Puff H-mode Plasmas: Theory and Implications

Energy Technology Data Exchange (ETDEWEB)

Goldston, R., E-mail: rgoldston@pppl.gov [Princeton Plasma Physics Laboratory, Princeton (United States)

2012-09-15

Full text: A heuristic model for the plasma scrape-off width in low-gas-puff tokamak H-mode plasmas is introduced. {nabla}B and curvature drifts into the scrape-off layer (SOL) are balanced against near-sonic parallel flows out of the SOL, to the divertor plates. These assumptions result in an estimated SOL width of order the poloidal gyroradius. It is next assumed that anomalous perpendicular electron thermal diffusivity is the dominant source of heat flux across the separatrix, investing the SOL width, derived above, with heat from the main plasma. The separatrix temperature is then calculated based on a two-point model balancing power input to the SOL with Spitzer-Hiarm parallel thermal conduction losses to the divertor. This results in a heuristic closed-form prediction for the power scrape-off width that is in quantitative agreement both in absolute magnitude and in scaling with recent experimental data. The applicability of the Spitzer-Harm model to this regime can be questioned at the lowest densities, where the presence of a sheath can raise the divertor target electron temperature. A more general two-point model including a finite ratio of divertor target to upstream electron temperature shows only a 5% effect on the SOL width with target temperature f{sub T} = 75% of upstream, so this effect is likely negligible in experimentally relevant regimes. To achieve the near-sonic flows measured experimentally, and assumed in this model, sets requirements on the ratio of upstream to total SOL particle sources relative to the square-root of the ratio of target to upstream temperature. As a result very high recycling regimes may allow significantly wider power fluxes. The Pfisch-Schluter model for equilibrium flows has been modified to allow near-sonic flows, appropriate for gradient scale lengths of order the poloidal gyroradius. This results in a new quadrupole flow pattern that amplifies the usual P-S flows at the outer midplane, while reducing them at the inner

Effect of lower hybrid waves on turbulence and transport of particles and energy in the FTU tokamak scrape-off layer plasma

Energy Technology Data Exchange (ETDEWEB)

Ridolfini, V Pericoli [ENEA-CR Frascati, Via Enrico Fermi 45-00044 Frascati, Roma (Italy)

2011-11-15

All the main features of the scrape-off layer turbulence, magnitude, frequency spectrum and perpendicular wave vector, {xi}{sub t}, are strongly affected by the injection of lower hybrid (LH) power into the FTU tokamak. The governing parameters are the local last closed magnetic surface values of density, n{sub e,LCMS}, and temperature, T{sub e,LCMS}. n{sub e,LCMS} determines the perpendicular wave vector of the LH waves, which is a key parameter for the multiple scattering processes, and together with T{sub e,LCMS} the collisionality that exerts a stabilizing effect on the fluctuations. This effect, still to be examined in the light of theoretical models, leads to an asymptotic value for the fluctuation relative amplitude in the ohmic phase close to 25%, and {approx}10% in the LH phase, or even less, since the saturation level is not yet attained. The LH waves also can strongly raise {xi}{sub t}, about 3 times, and double the root mean square frequency. The transfer of momentum and energy in the mutual scattering of LH and turbulence 'waves' drives these changes. An increase also of the cross-correlation between temperature and electric potential fluctuations should occur in order to explain the magnitude of the fluctuation amplitude drop and the large increment of the temperature e-folding decay, by more than a factor of 2.5. Particle transport, however, does not appear to be affected to a large extent-the density e-folding decay length is almost unchanged but the power flow typical length rises by about a factor of 1.5, which is a relevant figure in view of the problem of mitigating the power loads on divertor targets in future reactors. These changes are confined mainly within the flux tube connected with the LH waves launching antenna, but start to spread significantly out of it at high plasma densities.

Heuristic Drift-based Model of the Power Scrape-off width in H-mode Tokamaks

International Nuclear Information System (INIS)

Goldston, Robert J.

2011-01-01

An heuristic model for the plasma scrape-off width in H-mode plasmas is introduced. Grad B and curv B drifts into the SOL are balanced against sonic parallel flows out of the SOL, to the divertor plates. The overall particle flow pattern posited is a modification for open field lines of Pfirsch-Shlueter flows to include sinks to the divertors. These assumptions result in an estimated SOL width of ∼ 2αρ p /R. They also result in a first-principles calculation of the particle confinement time of H-mode plasmas, qualitatively consistent with experimental observations. It is next assumed that anomalous perpendicular electron thermal diffusivity is the dominant source of heat flux across the separatrix, investing the SOL width, defined above, with heat from the main plasma. The separatrix temperature is calculated based on a two-point model balancing power input to the SOL with Spitzer-Haerm parallel thermal conduction losses to the divertor. This results in a heuristic closed-form prediction for the power scrape-off width that is in reasonable quantitative agreement both in absolute magnitude and in scaling with recent experimental data from deuterium plasmas. Further work should include full numerical calculations, including all magnetic and electric drifts, as well as more thorough comparison with experimental data.

Transport code calculations concerning the plasma parameters in the scrape-off layer of poloidal limiter and the possible advantage of high Z wall materials in the cool plasma blanket approach

International Nuclear Information System (INIS)

Nicolai, A.; Fuchs, G.

1978-01-01

The plasma parameters in the scrape-off layer (SoL) of a tokamak are calculated by introducing appropriate particles and energy loss terms into the six-regime version of Duechs code. These terms take secondary electron smission from the limiter surface and a potential sheath in front of it into account. In the SoL Bohn diffusion is assumed. Limiter materials with large secondary emission coefficients (SEC)(e.g. Mo) give lower potential steps (U = 90 V) than low SEC materials (e.g. Be) which cause (U = 250 V). The flux of the sputtered liner material and the resulting radiation losses can be decreased by neutral gas influx. When the same neutral gas influx and the same additional heating are used, it is found that radiation losses due to molybdenum are lower than those due to iron, although Mo is more toxic. (Auth.)

Edge transport studies in the edge and scrape-off layer of the National Spherical Torus Experiment with Langmuir probes

Energy Technology Data Exchange (ETDEWEB)

Boedo, J. A., E-mail: jboedo@ucsd.edu; Rudakov, D. L. [University of California San Diego, 9500 Gilman Dr., La Jolla, California 92093 (United States); Myra, J. R.; D' Ippolito, D. A. [Lodestar Research Corp, 2400 Central Ave., Boulder, Colorado 80301 (United States); Zweben, S.; Maingi, R.; Maqueda, R. J.; Bell, R.; Kugel, H.; Leblanc, B.; Roquemore, L. A. [Princeton University, PO Box 451, Princeton, New Jersey 08543 (United States); Soukhanovskii, V. A. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Ahn, J. W.; Canik, J. [Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, Tennessee 37830 (United States); Crocker, N. [University of California Los Angeles, PO Box 957099, Los Angeles, California 90095 (United States)

2014-04-15

Transport and turbulence profiles were directly evaluated using probes for the first time in the edge and scrape-off layer (SOL) of NSTX [Ono et al., Nucl. Fusion 40, 557 (2000)] in low (L) and high (H) confinement, low power (P{sub in}∼ 1.3 MW), beam-heated, lower single-null discharges. Radial turbulent particle fluxes peak near the last closed flux surface (LCFS) at ≈4×10{sup 21} s{sup −1} in L-mode and are suppressed to ≈0.2×10{sup 21} s{sup −1} in H mode (80%–90% lower) mostly due to a reduction in density fluctuation amplitude and of the phase between density and radial velocity fluctuations. The radial particle fluxes are consistent with particle inventory based on SOLPS fluid modeling. A strong intermittent component is identified. Hot, dense plasma filaments 4–10 cm in diameter, appear first ∼2 cm inside the LCFS at a rate of ∼1×10{sup 21} s{sup −1} and leave that region with radial speeds of ∼3–5 km/s, decaying as they travel through the SOL, while voids travel inward toward the core. Profiles of normalized fluctuations feature levels of 10% inside LCFS to ∼150% at the LCFS and SOL. Once properly normalized, the intermittency in NSTX falls in similar electrostatic instability regimes as seen in other devices. The L-H transition causes a drop in the intermittent filaments velocity, amplitude and number in the SOL, resulting in reduced outward transport away from the edge and a less dense SOL.

Measurements of the parallel wavenumber of lower hybrid waves in the scrape-off layer of a high-density tokamak

International Nuclear Information System (INIS)

Baek, S. G.; Wallace, G. M.; Parker, R. R.; Shiraiwa, S.; Bonoli, P. T.; Brunner, D.; Faust, I.; LaBombard, B. L.; Wukitch, S.; Shinya, T.; Takase, Y.

2016-01-01

In lower hybrid current drive (LHCD) experiments on tokamaks, the parallel wavenumber of lower hybrid waves is an important physics parameter that governs the wave propagation and absorption physics. However, this parameter has not been experimentally well-characterized in the present-day high density tokamaks, despite the advances in the wave physics modeling. In this paper, we present the first measurement of the dominant parallel wavenumber of lower hybrid waves in the scrape-off layer (SOL) of the Alcator C-Mod tokamak with an array of magnetic loop probes. The electric field strength measured with the probe in typical C-Mod plasmas is about one-fifth of that of the electric field at the mouth of the grill antenna. The amplitude and phase responses of the measured signals on the applied power spectrum are consistent with the expected wave energy propagation. At higher density, the observed k || increases for the fixed launched k || , and the wave amplitude decreases rapidly. This decrease is correlated with the loss of LHCD efficiency at high density, suggesting the presence of loss mechanisms. Evidence of the spectral broadening mechanisms is observed in the frequency spectra. However, no clear modifications in the dominant k || are observed in the spectrally broadened wave components, as compared to the measured k || at the applied frequency. It could be due to (1) the probe being in the SOL and (2) the limited k || resolution of the diagnostic. Future experiments are planned to investigate the roles of the observed spectral broadening mechanisms on the LH density limit problem in the strong single pass damping regime.

An Heuristic Drift-Based Model of the Power Scrape-Off Width in H-Mode Tokamaks

International Nuclear Information System (INIS)

Goldston, Robert J.

2011-01-01

An heuristic model for the plasma scrape-off width in H-mode plasmas is introduced. Grad B and curv B drifts into the SOL are balanced against sonic parallel flows out of the SOL, to the divertor plates. The overall mass flow pattern posited is a modification for open field lines of Pfirsch-Shlueter flows to include sinks to the divertors. These assumptions result in an estimated SOL width of 2αρ p /R. They also result in a first-principles calculation of the particle confinement time of H-mode plasmas, qualitatively consistent with experimental observations. It is next assumed that anomalous perpendicular electron thermal diffusivity is the dominant source of heat flux across the separatrix, investing the SOL width, defined above, with heat from the main plasma. The separatrix temperature is calculated based on a two-point model balancing power input to the SOL with Spitzer-Haerm parallel thermal conduction losses to the divertor. This results in an heuristic closed-form prediction for the power scrape-off width that is in remarkable quantitative agreement both in absolute magnitude and in scaling with recent experimental data. Further work should include full numerical calculations, including all magnetic and electric drifts, as well as more thorough comparison with experimental data.

Far-reaching Impact of Intermittent Transport across the Scrape-off Layer: Latest Results from ASDEX Upgrade

Energy Technology Data Exchange (ETDEWEB)

Kocan, M.; Muller, W.; Conway, G.; De Marne, P.; Eich, T.; Fischer, R.; Fuchs, C.; Herrmann, A.; Ionita, C.; Kallenbach, A.; Lunt, T.; Maraschek, M.; Muller, S.; Nold, B.; Ribeiro, T.; Rohde, V.; Scott, B.; Stroth, U.; Suttrop, W.; Wolfrum, E., E-mail: martin.kocan@ipp.mpg.de [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, Garching (Germany); Adamek, J.; Horacek, J.; Komm, M. [Association EURATOM-IPP CR, Prague (Czech Republic); Gennrich, F.; Maszl, C.; Mehlmann, F.; Schrittwieser, R. [Institute for Ion Physics and Applied Physics, Association Euratom-OAW (Austria); Huang, Z. [Institut fuer Plasmaforschung, Universitat Stuttgart, Stuttgart (Germany)

2012-09-15

Full text: Latest research of intermittent transport in the scrape-off layer (SOL) of the ASDEX Upgrade tokamak is presented. Near the separatrix the fluctuations of the plasma and the floating potentials, measured by various Langmuir probes (LPs), are found to be anti-correlated due to fluctuations of the electron temperature. This indicates that, in contrast to a widely used experimental practice, a free exchange of both potentials is unjustified and can lead to significant error. Measurements of ion energies in turbulent L-mode and ELM filaments were carried out using a retarding field analyzer. In L-mode plasma, the filament ion temperature measured at 2 cm outside the separatrix is 80 - 110 eV, i.e., 3 - 4x the background ion temperature. Turbulent filaments also convect plasma to the wall with larger density than the background plasma density. Qualitatively similar observations were obtained during inter-ELM periods. Such enhanced particle and energy fluxes can potentially raise the erosion of the first wall in ITER. The ion temperature averaged over an ELM measured 35 - 60 mm outside the separatrix is in the range of 20 - 200 eV (5 - 50% of the pedestal top ion temperature). This demonstrates that ELM filaments carry hot ions over large radial distances in the SOL, which, in turn, can lead to enhanced sputtering from the first wall in future tokamaks. Lowest ion energies are observed during ELMs mitigated by in-vessel magnetic perturbations (MPs). The ELM ion temperature in the far SOL is found to increase with the ELM energy, indicating that on average the filaments in large ELMs propagate faster radially. The filamentary structure of the ion current density measured by LPs at the outboard mid-plane during mitigated ELMs is qualitatively similar to that observed during type I ELMs. The amplitude of the ion current density decreases only slightly when ELMs are mitigated, but, in contrast to type I ELMs, bursts of the ion current are observed throughout the

Effect of the scrape-off layer in AORSA full wave simulations of fast wave minority, mid/high harmonic, and helicon heating regimes

Energy Technology Data Exchange (ETDEWEB)

Bertelli, N., E-mail: nbertell@pppl.gov; Gerhardt, S.; Hosea, J. C.; LeBlanc, B.; Perkins, R. J.; Phillips, C. K.; Taylor, G.; Valeo, E. J.; Wilson, J. R. [Princeton Plasma Physics Laboratory, Princeton, NJ 08543 (United States); Jaeger, E. F. [XCEL Engineering Inc., Oak Ridge, TN 37830 (United States); Lau, C.; Blazevski, D.; Green, D. L.; Berry, L.; Ryan, P. M. [Oak Ridge National Laboratory, Oak Ridge, TN 37831-6169 (United States); Bonoli, P. T.; Wright, J. C. [MIT Plasma Science and Fusion Center, Cambridge, MA 02139 (United States); Pinsker, R. I.; Prater, R. [General Atomics, PO Box 85608, San Diego, CA 92186-5608 (United States); Qin, C. M. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); and others

2015-12-10

Several experiments on different machines and in different fast wave (FW) heating regimes, such as hydrogen minority heating and high harmonic fast waves, have found strong interactions between radio-frequency (RF) waves and the scrape-off layer (SOL) region. This paper examines the propagation and the power loss in the SOL by using the full wave code AORSA, in which the edge plasma beyond the last closed flux surface (LCFS) is included in the solution domain and a collisional damping parameter is used as a proxy to represent the real, and most likely nonlinear, damping processes. 3D AORSA results for the National Spherical Torus eXperiment (NSTX), where a full antenna spectrum is reconstructed, are shown, confirming the same behavior found for a single toroidal mode results in Bertelli et al, Nucl. Fusion, 54 083004, 2014, namely, a strong transition to higher SOL power losses (driven by the RF field) when the FW cut-off is moved away from in front of the antenna by increasing the edge density. Additionally, full wave simulations have been extended to “conventional” tokamaks with higher aspect ratios, such as the DIII-D, Alcator C-Mod, and EAST devices. DIII-D results show similar behavior found in NSTX and NSTX-U, consistent with previous DIII-D experimental observations. In contrast, a different behavior has been found for Alcator C-Mod and EAST, which operate in the minority heating regime unlike NSTX/NSTX-U and DIII-D, which operate in the mid/high harmonic regime. A substantial discussion of some of the main aspects, such as (i) the pitch angle of the magnetic field; (ii) minority heating vs. mid/high harmonic regimes is presented showing the different behavior of the RF field in the SOL region for NSTX-U scenarios with different plasma current. Finally, the preliminary results of the impact of the SOL region on the evaluation of the helicon current drive efficiency in DIII-D is presented for the first time and briefly compared with the different regimes

Investigation into the formation of the scrape-off layer density shoulder in JET ITER-like wall L-mode and H-mode plasmas

Science.gov (United States)

Wynn, A.; Lipschultz, B.; Cziegler, I.; Harrison, J.; Jaervinen, A.; Matthews, G. F.; Schmitz, J.; Tal, B.; Brix, M.; Guillemaut, C.; Frigione, D.; Huber, A.; Joffrin, E.; Kruzei, U.; Militello, F.; Nielsen, A.; Walkden, N. R.; Wiesen, S.; Contributors, JET

2018-05-01

The low temperature boundary layer plasma (scrape-off layer or SOL) between the hot core and the surrounding vessel determines the level of power loading, erosion and implantation of material surfaces, and thus the viability of tokamak-based fusion as an energy source. This study explores mechanisms affecting the formation of flattened density profiles, so-called ‘density shoulders’, in the low-field side (LFS) SOL, which modify ion and neutral fluxes to surfaces—and subsequent erosion. We find that increases in SOL parallel resistivity, Λdiv (=[L || ν eiΩi]/c sΩe), postulated to lead to shoulder growth through changes in SOL turbulence characteristics, correlates with increases in SOL shoulder amplitude, A s, only under a subset of conditions (D2-fuelled L-mode density scans with outer strike point on the horizontal target). Λdiv fails to correlate with A s for cases of N2 seeding or during sweeping of the strike point across the horizontal target. The limited correlation of Λdiv and A s is also found for H-mode discharges. Thus, while it may be necessary for Λdiv to be above a threshold of ~1 for shoulder formation and/or growth, another mechanism is required. More significantly, we find that in contrast to parallel resistivity, outer divertor recycling, as quantified by the total outer divertor Balmer D α emission, I-D α , does scale with A s where Λdiv does and even where Λdiv does not. Divertor recycling could lead to SOL density shoulder formation through: (a) reducing the parallel to the field flow (loss) of ions out of the SOL to the divertor; and (b) changes in radial electric fields which lead to E  ×  B poloidal flows as well as potentially affecting SOL turbulence birth characteristics. Thus, changes in divertor recycling may be the sole process involved in bringing about SOL density shoulders or it may be that it acts in tandem with parallel resistivity.

Interpretation of scrape-off layer profile evolution and first-wall ion flux statistics on JET using a stochastic framework based on fillamentary motion

Science.gov (United States)

Walkden, N. R.; Wynn, A.; Militello, F.; Lipschultz, B.; Matthews, G.; Guillemaut, C.; Harrison, J.; Moulton, D.; Contributors, JET

2017-08-01

This paper presents the use of a novel modelling technique based around intermittent transport due to filament motion, to interpret experimental profile and fluctuation data in the scrape-off layer (SOL) of JET during the onset and evolution of a density profile shoulder. A baseline case is established, prior to shoulder formation, and the stochastic model is shown to be capable of simultaneously matching the time averaged profile measurement as well as the PDF shape and autocorrelation function from the ion-saturation current time series at the outer wall. Aspects of the stochastic model are then varied with the aim of producing a profile shoulder with statistical measurements consistent with experiment. This is achieved through a strong localised reduction in the density sink acting on the filaments within the model. The required reduction of the density sink occurs over a highly localised region with the timescale of the density sink increased by a factor of 25. This alone is found to be insufficient to model the expansion and flattening of the shoulder region as the density increases, which requires additional changes within the stochastic model. An example is found which includes both a reduction in the density sink and filament acceleration and provides a consistent match to the experimental data as the shoulder expands, though the uniqueness of this solution can not be guaranteed. Within the context of the stochastic model, this implies that the localised reduction in the density sink can trigger shoulder formation, but additional physics is required to explain the subsequent evolution of the profile.

Role of stochasticity in turbulence and convective intermittent transport at the scrape off layer of Ohmic plasma in QUEST

International Nuclear Information System (INIS)

Banerjee, Santanu; Ishiguro, M.; Tashima, S.; Mishra, K.; Zushi, H.; Hanada, K.; Nakamura, K.; Idei, H.; Hasegawa, M.; Fujisawa, A.; Nagashima, Y.; Matsuoka, K.; Nishino, N.; Liu, H. Q.

2014-01-01

Statistical features of fluctuations are investigated using the fast camera imaging technique in the scrape of layer (SOL) of electron cyclotron resonance heated Ohmic plasma. Fluctuations in the SOL towards low field side are dominated by coherent convective structures (blobs). Two dimensional structures of the higher order moments (skewness s and kurtosis k) representing the shape of probability density function (PDF) are studied. s and k are seen to be functions of the magnetic field lines. s and k are consistently higher towards the bottom half of the vessel in the SOL showing the blob trajectory along the field lines from the top towards bottom of the vessel. Parabolic relation (k=As 2 +C) is observed between s and k near the plasma boundary, featuring steep density gradient region and at the far SOL. The coefficient A, obtained experimentally, indicates a shift of prominence from pure drift-wave instabilities towards fully developed turbulence. Numerical coefficients characterizing the Pearson system are derived which demonstrates the progressive deviation of the PDF from Gaussian towards gamma from the density gradient region, towards the far SOL. Based on a simple stochastic differential equation, a direct correspondence between the multiplicative noise amplitude, increased intermittency, and hence change in PDF is discussed

Control of long range turbulent transport with biasing in the tokamak scrape-off-layer

International Nuclear Information System (INIS)

Figarella, C.F.; Ghendrih, Ph.; Sarazin, Y.; Attuel, G.; Benkadda, S.; Beyer, P.; Falchetto, G.; Fleurence, E.; Garbet, X.; Grandgirard, V.

2005-01-01

Cross-field transport in the SOL influences tokamak performance in particular regarding the divertor efficiency. Recent experiment evidence emphasizes non-exponential and/or flat SOL profiles that suggest a large perpendicular transport. A 2D fluid model based on the interchange instability to simulate the SOL turbulence was found to exhibits intermittent dynamics of the particle flux. We propose a control method that prevents long range transport events from reaching the far SOL: It consists in biasing the far SOL leading to a transport barrier which stops the propagation of these intermittent events. The best trade off is to localize the biased toroidal ring around the baffles. We show that such a control is achievable providing the strength of the barrier is strong enough. The investigation of the minimal biasing power required to achieve the control as well as its experimental estimate is performed

Palm trees and islands – Current filaments in the edge of JET

DEFF Research Database (Denmark)

Maszl, Ch.; Naulin, Volker; Brix, M.

2011-01-01

It is now well known that edge localized modes (ELMs) lead to the ejection of a number of filamentary structures into the scrape-off layer (SOL). ELMs thus generate structures with excess energy and density. Recent results show that ELM filaments also carry current. Furthermore it can be conjectu......It is now well known that edge localized modes (ELMs) lead to the ejection of a number of filamentary structures into the scrape-off layer (SOL). ELMs thus generate structures with excess energy and density. Recent results show that ELM filaments also carry current. Furthermore it can...

Exposure of metal mirrors in the scrape-off layer of TEXTOR

International Nuclear Information System (INIS)

Wienhold, P.; Litnovsky, A.; Philipps, V.; Schweer, B.; Sergienko, G.; Oelhafen, P.; Ley, M.; De Temmerman, G.; Schneider, W.; Hildebrandt, D.; Laux, M.; Rubel, M.; Emmoth, B.

2005-01-01

Large molybdenum mirrors have been exposed in the SOL of TEXTOR in order to simulate conditions relevant for ITER optical components. Distortions of the reflectivity - increase as well as decrease - are found in the erosion and deposition dominated areas, respectively. The changes are most pronounced in the near UV and level off in the IR and can partly be attributed to observed surface changes. A novel periscope system was installed and mirrors exposed in a pilot experiment to simulate the transmission of light to distant sensors in ITER

Quantitative determination of 3,4-methylenedioxymethamphetamine by thin-layer chromatography in ecstasy illicit pills in Tehran.

Science.gov (United States)

Shetab Boushehri, Seyed Vahid; Tamimi, Maryam; Kebriaeezadeh, Abbas

2009-11-01

3,4-Methylenedioxymethamphetamine (MDMA) is the major ingredient of ecstasy illicit pills. It is a hallucinogen, central nervous system stimulant, and serotonergic neurotoxin that strongly releases serotonin from serotonergic nerves terminals. Moreover, it releases norepinephrine and dopamine from nerves terminal, but to a lesser extent than serotonin. Poisoning and even death from abusing MDMA-containing ecstasy illicit pills among abusers is usual. Thus, quantitative determination of MDMA content of ecstasy illicit pills in illicit drug bazaar must be done regularly to find the most high dose ecstasy illicit pills and removing them from illicit drug bazaar. In the present study, MDMA contents of 13 most abundant ecstasy illicit pills were determined by quantitative thin-layer chromatography (TLC). Two procedures for quantitative determination of MDMA contents of ecstasy illicit pills by TLC were used: densitometric and so-called 'scraping off' methods. The former was done in a reflection mode at 285 nm and the latter was done by absorbance measurement of eluted scraped off spots. Limit of detection (LOD), considering signal-to-noise ratio (S/N) of 2, and limit of quantification (LOQ), regarding S/N of 10, of densitometric and scraping off methods were 0.40 microg, 1.20 microg, and 6.87 mug, 20.63 microg, respectively. Repeatabilities (within-laboratory error) of densitometric and scraping off methods were 0.5% and 3.6%, respectively. The results showed that the ecstasy illicit pills contained 24-124.5 mg and 23.9-122.2 mg MDMA by densitometric and scraping off methods, respectively.

Ultrasonic Evaluation of the Pull-Off Adhesion between Added Repair Layer and a Concrete Substrate

Science.gov (United States)

Czarnecki, Slawomir

2017-10-01

This paper concerns the evaluation of the pull-off adhesion between a concrete added repair layer with variable thickness and a concrete substrate, based on parameters assessed using ultrasonic pulse velocity (UPV) method. In construction practice, the experimental determination of pull-off adhesion f b, between added repair layer and a concrete substrate is necessary to assess the quality of repair. This is usually carried out with the use of pull-off method which results in local damage of the added concrete layer in all the testing areas. Bearing this in mind, it is important to describe the method without these disadvantages. The prediction of the pull-off adhesion of the two-layer concrete elements with variable thickness of each layer might be provided by means of UPV method with two-sided access to the investigated element. For this purpose, two-layered cylindrical specimens were obtained by drilling the borehole from a large size specially prepared concrete element. Those two-layer elements were made out of concrete substrate layer and Polymer Cement Concrete (PCC) mortar as an added repair layer. The values of pull-off adhesion f b of the elements were determined before obtaining the samples by using the semi-destructive pull-off method. The ultrasonic wave velocity was determined in samples with variable thickness of each layer and was then compared to theoretical ultrasonic wave velocity predicted for those specimens. The regression curve for the dependence of velocity and pull-off adhesion, determined by the pulloff method, was made. It has been proved that together with an increase of ratio of investigated ultrasonic wave velocity divided by theoretical ultrasonic wave velocity, the pull-off adhesion value f b between added repair layer with variable thickness and a substrate layer also increases.

Tokamak fusion reactor exhaust

International Nuclear Information System (INIS)

Harrison, M.F.A.; Harbour, P.J.; Hotston, E.S.

1981-08-01

This report presents a compilation of papers dealing with reactor exhaust which were produced as part of the TIGER Tokamak Installation for Generating Electricity study at Culham. The papers are entitled: (1) Exhaust impurity control and refuelling. (2) Consideration of the physical problems of a self-consistent exhaust and divertor system for a long burn Tokamak. (3) Possible bundle divertors for INTOR and TIGER. (4) Consideration of various magnetic divertor configurations for INTOR and TIGER. (5) A appraisal of divertor experiments. (6) Hybrid divertors on INTOR. (7) Refuelling and the scrape-off layer of INTOR. (8) Simple modelling of the scrape-off layer. (9) Power flow in the scrape-off layer. (10) A model of particle transport within the scrape-off plasma and divertor. (11) Controlled recirculation of exhaust gas from the divertor into the scrape-off plasma. (U.K.)

Scrape-off layer properties of ITER-like limiter start-up plasmas in JET

Czech Academy of Sciences Publication Activity Database

Arnoux, G.; Farley, T.; Silva, C.; Devaux, S.; Firdaouss, M.; Frigione, D.; Goldston, R.J.; Gunn, J.; Horáček, Jan; Jachmich, S.; Lomas, P. J.; Marsen, S.; Matthews, G. F.; Pitts, R.A.; Stamp, M.; Stangeby, P.C.

2013-01-01

Roč. 53, č. 7 (2013), 073016-073016 ISSN 0029-5515 Institutional support: RVO:61389021 Keywords : Plasma-material interactions * boundary layer effect * power exhaust * divertors * electric and magnetic measurements * tokamaks * spherical tokamaks Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 3.243, year: 2013 http://iopscience.iop.org/0029-5515/53/7/073016/pdf/0029-5515_53_7_073016.pdf

Relevance, Realization and stability of a cold layer at the plasma edge for fusion reactors

International Nuclear Information System (INIS)

1990-09-01

The workshop was dedicated to the realization and stability of a cold layer at the plasma edge for fusion reactors. The subjects of the communications presented were: impurity transport, and control, plasma boundary layers, power balance, radiation control and modifications, limiter discharges, tokamak density limit, Asdex divertor discharges, thermal stability of a radiating diverted plasma, plasma stability, auxiliary heating in Textor, detached plasma in Tore Supra, poloidal divertor tokamak, radiation cooling, neutral-particle transport, plasma scrape-off layer, edge turbulence

Magnetic topology changes induced by lower hybrid waves and their profound effect on edge-localized modes in the EAST tokamak.

Science.gov (United States)

Liang, Y; Gong, X Z; Gan, K F; Gauthier, E; Wang, L; Rack, M; Wang, Y M; Zeng, L; Denner, P; Wingen, A; Lv, B; Ding, B J; Chen, R; Hu, L Q; Hu, J S; Liu, F K; Jie, Y X; Pearson, J; Qian, J P; Shan, J F; Shen, B; Shi, T H; Sun, Y; Wang, F D; Wang, H Q; Wang, M; Wu, Z W; Zhang, S B; Zhang, T; Zhang, X J; Yan, N; Xu, G S; Guo, H Y; Wan, B N; Li, J G

2013-06-07

Strong mitigation of edge-localized modes has been observed on Experimental Advanced Superconducting Tokamak, when lower hybrid waves (LHWs) are applied to H-mode plasmas with ion cyclotron resonant heating. This has been demonstrated to be due to the formation of helical current filaments flowing along field lines in the scrape-off layer induced by LHW. This leads to the splitting of the outer divertor strike points during LHWs similar to previous observations with resonant magnetic perturbations. The change in the magnetic topology has been qualitatively modeled by considering helical current filaments in a field-line-tracing code.

Electrostatic and magnetic fluctuations in the proximity of the velocity shear layer in the TJ-I Tokamak

International Nuclear Information System (INIS)

Garcia-Cortes, I.; Pedrosa, M.A.; Hidalgo, C.

1992-01-01

The structure of the electrostatic and magnetic turbulence changes in the proximity of the naturally velocity shear layer in the TJ-I tokamak. A decorrelation in the broad-band magnetic fluctuations and a decreasing in the density fluctuation levels have been observed in the proximity (scrape-off layer side) of the shear layer. The results are interpreted in terms of turbulence characteristics modified by sheared poloidal flows or/and magnetic configuration. (author) 8 fig. 16 ref

WebSelF: A Web Scraping Framework

DEFF Research Database (Denmark)

Thomsen, Jakob; Ernst, Erik; Brabrand, Claus

2012-01-01

We present, WebSelF, a framework for web scraping which models the process of web scraping and decomposes it into four conceptually independent, reusable, and composable constituents. We have validated our framework through a full parameterized implementation that is flexible enough to capture...... previous work on web scraping. We have experimentally evaluated our framework and implementation in an experiment that evaluated several qualitatively different web scraping constituents (including previous work and combinations hereof) on about 11,000 HTML pages on daily versions of 17 web sites over...... a period of more than one year. Our framework solves three concrete problems with current web scraping and our experimental results indicate that com- position of previous and our new techniques achieve a higher degree of accuracy, precision and specificity than existing techniques alone....

Study on off-momentum tail scraping in the LHC

CERN Document Server

Mirarchi, D; Bruce, R; CERN. Geneva. ATS Department

2014-01-01

A study on o-momentum tail population in the LHC was performed through collimator scraping at high dispersion region. High intensity measurements at the end of a physics ll with 25ns bunch spacing were carried out on 16th December 2012, using primary collimators (TCPs) in the momentum cleaning insertion (IR3) as scrapers. The o-momentum cuts were applied up to the level where the IR3 primary collimator is the aperture bottleneck for all particles outside the bucket, and the TCPs in the betatron cleaning insertion (IR7) are still the primary restriction of aperture of the machine in the transverse plane for particles inside the bucket. This because whether a particle is lost in IR3 or IR7 is not given only by the momentum oset but also by the betatron amplitude, as explained in the text. A signicant decay of the abort gap (AG) population was observed, while moving in the collimator jaw on the side where particles with negative o-momentum are expected. The level of the AG popupation achieved was at a similar le...

Dependence of the L-Mode scrape-off layer power fall-off length on the upper triangularity in TCV

Science.gov (United States)

Faitsch, M.; Maurizio, R.; Gallo, A.; Coda, S.; Eich, T.; Labit, B.; Merle, A.; Reimerdes, H.; Sieglin, B.; Theiler, C.; the Eurofusion MST1 Team; the TCV Team

2018-04-01

This paper reports on experimental observations on TCV with a scan in upper triangularity {δ }up}, including negative triangularity, focusing on the power fall-off length {λ }{{q}} in L-Mode. The upper triangularity is scanned from -0.28 to 0.47. Smaller {λ }{{q}}out} is measured at the outer divertor target for decreasing {δ }up} together with higher edge temperature {T}{{e},{edge}} leading to increased confinement. This effect is observed for both magnetic drift directions for discharges in deuterium and helium. In helium larger {λ }{{q}} values are observed compared to deuterium. The power fall-off length at the inner divertor target {λ }{{q}}in} has a non-monotonic behaviour with changing triangularity. The largest values are around {δ }up}=0. The ratio {λ }{{q}}in}/{λ }{{q}}out} increases for decreasing {δ }up} for positive triangularity and is approximately constant for negative triangularity. {λ }{{q}}out} is compared to available scaling laws. Partial agreement is only observed for a scaling law containing a proxy for {T}{{e},{edge}} at ASDEX Upgrade (Sieglin 2016 Plasma Phys. Control. Fusion 58 055015). Extending this scaling to TCV and using {T}{{e},{edge}} at {ρ }pol}=0.95 suggests that {λ }{{q}}out} is independent of machine size {λ }{{q}}{{L} - {Mode}} ({mm}) = 165\\cdot {B}pol}{({{T}})}-0.66\\cdot A{({{u}})}-0.15\\cdot {T}{{e},{edge}}{({eV})}-0.93\\cdot R{({{m}})}-0.03. Possible explanations for smaller {λ }{{q}}out} for decreasing {δ }up} is a reduction in turbulence or a direct effect of increasing {T}{{e},{edge}}.

Equation Chapter 1 Section 1Cross Layer Design for Localization in Large-Scale Underwater Sensor Networks

Directory of Open Access Journals (Sweden)

Yuanfeng ZHANG

2014-02-01

Full Text Available There are many technical challenges for designing large-scale underwater sensor networks, especially the sensor node localization. Although many papers studied for large-scale sensor node localization, previous studies mainly study the location algorithm without the cross layer design for localization. In this paper, by utilizing the network hierarchical structure of underwater sensor networks, we propose a new large-scale underwater acoustic localization scheme based on cross layer design. In this scheme, localization is performed in a hierarchical way, and the whole localization process focused on the physical layer, data link layer and application layer. We increase the pipeline parameters which matched the acoustic channel, added in MAC protocol to increase the authenticity of the large-scale underwater sensor networks, and made analysis of different location algorithm. We conduct extensive simulations, and our results show that MAC layer protocol and the localization algorithm all would affect the result of localization which can balance the trade-off between localization accuracy, localization coverage, and communication cost.

Fuel and helium confinement in fusion reactors

International Nuclear Information System (INIS)

Houlberg, W.A.; Attenberger, S.E.

1993-01-01

An expanded macroscopic model for particle confinement is used to investigate both fuel and helium confinement in reactor plasmas. The authors illustrate the relative effects of external sources of fuel, divertor pumping, and wall and divertory recycle on core, edge and scrape-off layer densities by using separate particle confinement times for open-quote core close-quote fueling (deep pellet or beam penetration, τ c ), open-quote shallow close-quote fueling (shallow pellet penetration or neutral atoms that penetrate the scrape-off layer, τ s ) and fueling in the scrape-off layer (τ sol ). Because τ s is determined by the parallel flow velocity and characteristic distance to the divertor plate, it can be orders of magnitude lower than either τ c or τ sol . A dense scrape-off region, desirable for reduced divertor erosion, leads to a high fraction of the recycled neutrals being ionized in the scrape-off region and poor core fueling efficiency. The overall fueling efficiency can then be dramatically improved with either shallow or deep auxillary fueling. Helium recycle is nearly always coupled to the scrape-off region and does not lead to strong core accumulation unless the helium pumping efficiency is much less than the fuel pumping efficiency, or the plasma preferentially retains helium over hydrogenic ions. Differences between the results of this model, single-τ p macroscopic models, and 1-D and 2-D models are discussed in terms of assumptions and boundary conditions

Palm trees and islands : current filaments in the edge of JET

NARCIS (Netherlands)

Maszl, Ch.; Naulin, V.; Brix, M.; Versloot, T.W.; Schrittwieser, R.

2011-01-01

It is now well known that edge localized modes (ELMs) lead to the ejection of a number of filamentary structures into the scrape-off layer (SOL). ELMs thus generate structures with excess energy and density. Recent results show that ELM filaments also carry current. Furthermore it can be conjectured

Palm trees and islands - Current filaments in the edge of JET

NARCIS (Netherlands)

Maszl, C.; Naulin, V.; Brix, M.; Versloot, T. W.; Schrittwieser, R.

2011-01-01

It is now well known that edge localized modes (ELMS) lead to the ejection of a number of filamentary structures into the scrape-off layer (SOL). ELMS thus generate structures with excess energy and density. Recent results show that ELM filaments also carry current. Furthermore it can be conjectured

Peeling-off of the external kink modes at tokamak plasma edge

International Nuclear Information System (INIS)

Zheng, L. J.; Furukawa, M.

2014-01-01

It is pointed out that there is a current jump between the edge plasma inside the last closed flux surface and the scrape-off layer and that the current jump can lead the external kink modes to convert to the tearing modes, due to the current interchange effects [L. J. Zheng and M. Furukawa, Phys. Plasmas 17, 052508 (2010)]. The magnetic reconnection in the presence of tearing modes subsequently causes the tokamak edge plasma to be peeled off to link to the divertors. In particular, the peeling or peeling-ballooning modes can become the “peeling-off” modes in this sense. This phenomenon indicates that the tokamak edge confinement can be worse than the expectation based on the conventional kink mode picture

Peeling-off of the external kink modes at tokamak plasma edge

Energy Technology Data Exchange (ETDEWEB)

Zheng, L. J. [Institute for Fusion Studies, University of Texas at Austin, Austin, Texas 78712 (United States); Furukawa, M. [Graduate School of Engineering, Tottori University, Tottori 680-8552 (Japan)

2014-08-15

It is pointed out that there is a current jump between the edge plasma inside the last closed flux surface and the scrape-off layer and that the current jump can lead the external kink modes to convert to the tearing modes, due to the current interchange effects [L. J. Zheng and M. Furukawa, Phys. Plasmas 17, 052508 (2010)]. The magnetic reconnection in the presence of tearing modes subsequently causes the tokamak edge plasma to be peeled off to link to the divertors. In particular, the peeling or peeling-ballooning modes can become the “peeling-off” modes in this sense. This phenomenon indicates that the tokamak edge confinement can be worse than the expectation based on the conventional kink mode picture.

Physics and modelling of scrape-off layer transport

International Nuclear Information System (INIS)

Cohen, R.H.; Allen, S.L.; Crotinger, J.A.; Kaiser, T.B.; Milovich, J.L.; Mattor, N.; Nevins, W.M.; Porter, G.D.; Rensink, M.E.; Rognlien, T.D.; Berk, H.L.; Diamond, P.H.; Rosenbluth, M.N.; Hinton, F.L.; Staebler, G.M.; Knoll, D.A.; Modi, B.; Xu, X.Q.; Prinja, A.K.; Ryutov, D.D.; Tsidulko, Y.A.

1992-01-01

We present studies of three schemes for reducing the peak heat flux on divertor plates, divertor biasing, impurity injection (''radiative divertor'') and neutral gas injection (''gas target divertor''). We report on theoretical analysis of a likely source of turbulent transport in the SOL and incorporation of the resultant transport coefficients into self-consistent models

Scrape-off layer and divertor theory meeting: Proceedings

International Nuclear Information System (INIS)

1994-03-01

This report contains viewgraphs on the following topics: fluid modelling of neutrals in the SOL and divertor; instabilities of gas-fueled divertors: theory and adaptive simulations; stability of ionization fronts of gaseous divertor plasmas; monte carlo calculation of heat transport; reduced charge model for edge impurity flows; thermally collapsed solutions for gaseous/radiative divertors; adaptive grid methods in transport simulation; advanced numerical solution algorithms applied to the multispecies edge plasma equations; two-dimensional edge plasma simulation using the multigrid method; neutral behavior and the effects of neutral-neutral and neutral-ion elastic scattering in the ITER gaseous divertor; particle throughput in the TPX divertor; marfes in tokamaks; a comparative study of the limiter and divertor edge plasmas in TEXT-U; issues of toroidal tokamak-type divertor simulators; ASDEX upgrade; the ITER divertor; the DIII-D divertor program and TPX divertor; DEGAS 2: a transmission/escape probabilities model for neutral particle transport: comparison with DEGAS 2; a collisional radiative model of hydrogen for high recycling divertors; comparison of fluid and non- fluid neutral models in B2.5; DIII-D radiative divertor simulations; 3-D fluid simulations of turbulence from conducting wall mode; turbulence and drifts in SOL plasmas; recent results for 1 1/2-D ITER gas target divertor modelling; evaluation of pumping and fueling in coupled core, SOL, and divertor chamber calculations; and ITER gas target divertors: comparison of volume recombination and large radial transport scenarios using DEGAS

Evaluation of Endotracheal Tube Scraping on Airway Resistance.

Science.gov (United States)

Scott, J Brady; Dubosky, Meagan N; Vines, David L; Sulaiman, Adewunmi S; Jendral, Kyle R; Singh, Gagan; Patel, Ankeet; Kaplan, Carl A; Gurka, David P; Balk, Robert A

2017-11-01

Spontaneous breathing trials (SBTs) are used to assess the readiness for discontinuation of mechanical ventilation. When airway resistance (R aw ) is elevated, the imposed work of breathing can lead to prolongation of mechanical ventilation. Biofilm and mucus build-up within the endotracheal tube (ETT) can increase R aw . Scraping the ETT can remove the biofilm build-up and decrease mechanical R aw . The primary aim of this study was to evaluate the impact of ETT scraping on R aw . The secondary aim was to determine whether decreasing R aw would impact subsequent SBT success. Intubated, mechanically ventilated subjects were enrolled if they failed an SBT and had an R aw of > 10 cm H 2 O/L/s. SBT failure was based on institutional guidelines, and R aw was calculated by subtracting the difference between the measured peak and plateau pressures using a square flow waveform with an inspiratory flow set at 60 L/min. The endOclear device was inserted into the ETT and withdrawn per manufacturer's guidelines. Scraping was repeated until the ETT was cleared. Change in R aw was compared pre- and post-ETT scraping using a paired t test. A Mann-Whitney U test evaluated the difference in percentage change in R aw between SBT groups. Twenty-nine subjects completed the study. The mean pre- and post-ETT scraping R aw values were 15.17 ± 3.83 and 12.05 ± 3.19 cm H 2 O/L/s, respectively ( P < .001). Subsequent SBT success was 48%; however, there was no difference in percentage change in R aw between subsequent passed SBT (18.61% [interquartile range 8.90-33.93%]) and failed SBT (23.88% [interquartile range 0.00-34.80%]), U = 78.5, z = -0.284, P = .78. No adverse events were noted with ETT scraping. This study demonstrated that ETT scraping can reduce R aw . The decrease in R aw post-ETT scraping did not affect subsequent SBT success. Copyright © 2017 by Daedalus Enterprises.

Combined core/boundary layer plasma transport simulations in tokamaks

International Nuclear Information System (INIS)

Prinja, A.K.; Schafer, R.F. Jr.; Conn, R.W.; Howe, H.C.

1987-01-01

Significant new numerical results are presented from self-consistent core and boundary or scrape-off layer plasma simulations with 3-D neutral transport calculations. For a symmetric belt limiter it is shown that, for plasma conditions considered here, the pump limiter collection efficiency increases from 11% to 18% of the core efflux as a result of local reionization of blade deflected neutrals. This hitherto unobserved effect causes a significant amplification of upstream ion flux entering the pump limiter. Results from coupling of an earlier developed two-zone edge plasma model ODESSA to the PROCTR core plasma simulation code indicates that intense recycling divertor operation may not be possible because of stagnation of upstream flow velocity. This results in a self-consistent reduction of density gradient in an intermediate region between the central plasma and separatrix, and a concomitant reduction of core-efflux. There is also evidence of increased recycling at the first wall. (orig.)

Impurity penetration and transport during VH-mode on DIII-D

International Nuclear Information System (INIS)

Lippmann, S.I.; Evans, T.E.; Jackson, G.L.; West, W.P.

1992-05-01

A new modeling effort is made in order to understand the observed relatively low levels of impurity contamination during the VH-mode phase on DIII-D, as compared to those observed during the H-mode phase of selected discharges. The key element is the inclusion of the real 2-D flux surface geometry in the prediction of impurity penetration of sputtered atoms through the scrape-off layer into the core plasma. Of the elements which determine the impurity content in the plasma: sputtering yield, penetration, and core transport, the penetration through the scrape-off layer is found to be the most determinative factor. The low impurity content in VH-mode is attributed to the development of a scrape-off layer with higher density and temperature properties than those normally obtained in H-mode

Local electromagnetic waves in layered superconductors

International Nuclear Information System (INIS)

Gvozdikov, V.M.; Vega-Monroy, R.

1999-01-01

A dispersion equation for electromagnetic waves localized on a defect layer of a layered superconductor is obtained in the frame of a model which neglects electron hopping between layers but assumes an arbitrary current-current response function within the layers. The defect layer differs from the rest of the layers by density and mass of charge carriers. It is shown that near the critical temperature in the London limit the local mode lies within the superconducting gap and has a wave vector threshold depending on the layered crystal and defect layer parameters. In the case of highly anisotropic layered superconductors, like Bi- or Tl-based high-T c cuprates, the local mode exists within a narrow range of positive variations of the mass and charge carriers. (author)

Instant web scraping with Java

CERN Document Server

Mitchell, Ryan

2013-01-01

This book is full of short, concise recipes to learn a variety of useful web scraping techniques using Java. You will start with a simple basic recipe of setting up your Java environment and gradually learn some more advanced recipes such as using complex Scrapers.Instant Web Scraping with Java is aimed at developers who, while not necessarily familiar with Java, are at least ready to dive into the complexities of this language with simple, step-by-step instructions leading the way. It is assumed that you have at least an intermediate knowledge of HTML, some knowledge of MySQL, and access to a

Characteristics of algal succession following rock scraping at Imwon area in the east coast of Korea

Science.gov (United States)

Kim, Young Dae; Ahn, Jung Kwan; Nam, Myung Mo; Lee, Chu; Yoo, Hyun Il; Yeon, Su Yeoung; Kim, Young Hwan; Kim, Jang Kyun; Choi, Jae Suk

2016-12-01

This study was conducted to clarify the characteristics of algal succession following rock scraping using hoe or high-pressure water sprayer in the period from June 2010 to April 2011. We divided the research area off the eastern coast of Korean near Imwon into 3 categories depending upon the severity of the barren ground, i.e., the urchin barren-affected, urchin barren-ongoing and urchin barren-free areas. In April 2011, in the urchin barren-affected area with 25 seaweed species, the cover percentage and importance value (IV) of crustose coralline algae were higher than those of other species. In the urchin barren-ongoing area with 33 seaweed species, crustose coralline algae (mean IV = 62%) as well as Sargassum sp. (mean IV = 28%), and Gelidium amansii (mean IV = 19%) were observed following rock scraping. In the urchin barren-free area where seaweed communities were relatively abundant with 42 species, a variety of algal species including G. amansii (mean IV = 32%) underwent algal succession. Overall, it was observed that, as an aspect of algal succession, the weaker the barren ground severity was, the more frequent and diverse the seaweeds were, and the more complex the succession pattern was in the study. As an aspect of recovering algal community, rock scraping using hoe was shown to be superior to the method using high-pressure water spraying. Therefore, we conclude that rock scraping using hoe is a very effective strategy for recovering the algal community in urchin barren-ongoing area.

Shear flows at the tokamak edge and their interaction with edge-localized modes

International Nuclear Information System (INIS)

Aydemir, A. Y.

2007-01-01

Shear flows in the scrape-off layer (SOL) and the edge pedestal region of tokamaks are shown to arise naturally out of transport processes in a magnetohydrodynamic model. In quasi-steady-state conditions, collisional resistivity coupled with a simple bootstrap current model necessarily leads to poloidal and toroidal flows, mainly localized to the edge and SOL. The role of these flows in the grad-B drift direction dependence of the power threshold for the L (low) to H (high) transition, and their effect on core rotation, are discussed. Theoretical predictions based on symmetries of the underlying equations, coupled with computational results, are found to be in agreement with observations in Alcator C-Mod [Phys. Plasmas 12, 056111 (2005)]. The effects of these self-consistent flows on linear peeling/ballooning modes and their nonlinear consequences are also examined

Numerical Modeling of Edge-Localized-Mode Filaments on Divertor Plates Based on Thermoelectric Currents

International Nuclear Information System (INIS)

Wingen, A.; Spatschek, K. H.; Evans, T. E.; Lasnier, C. J.

2010-01-01

Edge localized modes (ELMs) are qualitatively and quantitatively modeled in tokamaks using current bursts which have been observed in the scrape-off-layer (SOL) during an ELM crash. During the initial phase of an ELM, a heat pulse causes thermoelectric currents. They first flow in short connection length flux tubes which are initially established by error fields or other nonaxisymmetric magnetic perturbations. The currents change the magnetic field topology in such a way that larger areas of short connection length flux tubes emerge. Then currents predominantly flow in short SOL-like flux tubes and scale with the area of the flux tube assuming a constant current density. Quantitative predictions of flux tube patterns for a given current are in excellent agreement with measurements of the heat load and current flow at the DIII-D target plates during an ELM cycle.

Color Image of Snow White Trenches and Scraping

Science.gov (United States)

2008-01-01

This image was acquired by NASA's Phoenix Mars Lander's Surface Stereo Imager on the 31st Martian day of the mission, or Sol 31 (June 26, 2008), after the May 25, 2008 landing. This image shows the trenches informally called 'Snow White 1' (left), 'Snow White 2' (right), and within the Snow White 2 trench, the smaller scraping area called 'Snow White 3.' The Snow White 3 scraped area is about 5 centimeters (2 inches) deep. The dug and scraped areas are within the diggiing site called 'Wonderland.' The Snow White trenches and scraping prove that scientists can take surface soil samples, subsurface soil samples, and icy samples all from one unit. Scientists want to test samples to determine if some ice in the soil may have been liquid in the past during warmer climate cycles. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is led by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver

MD 2179: Scraping of off-momentum halo after injection

CERN Document Server

Garcia Morales, Hector; Patecki, Marcin; Wretborn, Sven Joel; CERN. Geneva. ATS Department

2018-01-01

In this MD, a beam scraping was performed using the momentum primary collimator in IR3 where dispersion is high. A second scraping was performed using a TCSG in IR7 where dispersion is almost negligible. In such a way, we aim to disentangle the contribution of off-momentum particles to halo population. These scrapings will provide useful information to better understand the usual off-momentum losses we see at the start of the ramp. The MD results would also be used to benchmark simulations of off-momentum beam losses in order to gain confidence in simulation models.

Fracture and flaking off behavior of coated layer of DyBCO coated conductor under applied tensile strain

International Nuclear Information System (INIS)

Arai, T.; Shin, J.K.; Matsubayashi, H.; Ochiai, S.; Okuda, H.; Osamura, K.; Prusseit, W.

2009-01-01

The tensile behavior of the DyBa 2 Cu 3 O 7-δ (DyBCO) coated conductor with MgO buffer layer deposited on the Hastelloy C-276 substrate by inclined substrate deposition (ISD) was studied. The tensile stress-strain curve showed a flat region, characterized by the discontinuous yielding of the substrate due to the Lueders band extension from the gripped portions of the sample. In the area where the Lueders band had passed, the coating layer showed severe multiple transverse cracking due to the localized plastic deformation of the substrate. The flaking off of the coating layers took place at high applied strain, due to the buckling fracture of the coated layers in the sample width direction, accompanied by the interfacial debonding.

Particle supply and recovery device

International Nuclear Information System (INIS)

Yamada, Kimio; Okazaki, Takashi.

1988-01-01

This invention concerns a particle supply and recovery device suitable to the supply of fuels and exhaustion of reaction products in a tokamak device. The divertor chamber is divided into an inner side and an outer side, in which only the outer side is constituted as a tightly closed structure. Particles are supplied from the inside of main plasmas and exhausted from the outer side of the divertor chamber. In the divertor equilibrium arrangement, particles escaping from the main plasmas are conveyed mainly passing through the outer side scrape-off layer to the divertor chamber. The particle density is higher at the outer side and lower at the inner side of the scrape-off layer. By making the outer side as a tightly closed structure, the pressure is increased and the particle exhaustion efficiency is improved. Since the particle density is low in the inner scrape-layer, the particle supply efficiency to the main plasma is increased by supplying the particles from the inside. Further, particles ionized in the inner scrape-off layer are returned to the main plasma chamber and then supplied again since the inner divertor chamber is not closed. Accordingly, the particle supply efficiency can further be improved. (K.M.)

Propagation of the lower hybrid wave in a density fluctuating scrape-off layer (SOL)

International Nuclear Information System (INIS)

Madi, M; Peysson, Y; Decker, J; Kabalan, K Y

2015-01-01

The perturbation of the lower hybrid wave (LH) power spectrum by fluctuations of the plasma in the vicinity of the antenna is investigated by solving the full wave equation in a slab geometry using COMSOL Multiphysics®. The numerical model whose generality allows to study the effect of various types of fluctuations, including those with short characteristic wavelengths is validated against a coupling code in quiescent regimes. When electron density fluctuations along the toroidal direction are incorporated in the dielectric tensor over a thin perturbed layer in front of the grill, the power spectrum may be strongly modified from the antenna mouth to the plasma separatrix as the LH wave propagates. The diffraction effect by density fluctuations leads to the appearance of multiple satellite lobes with randomly varying positions and the averaged perturbation is found to be maximum for the Fourier components of the fluctuating spectrum in the vicinity of the launched LH wavelength. This highlights that fast toroidal inhomogeneities with short characteristics length scales in front of the grill may change significantly the initial LH power spectrum used in coupled ray-tracing and Fokker–Planck calculations. (paper)

ERO modeling and sensitivity analysis of locally enhanced beryllium erosion by magnetically connected antennas

Science.gov (United States)

Lasa, A.; Borodin, D.; Canik, J. M.; Klepper, C. C.; Groth, M.; Kirschner, A.; Airila, M. I.; Borodkina, I.; Ding, R.; Contributors, JET

2018-01-01

Experiments at JET showed locally enhanced, asymmetric beryllium (Be) erosion at outer wall limiters when magnetically connected ICRH antennas were in operation. A first modeling effort using the 3D erosion and scrape-off layer impurity transport modeling code ERO reproduced qualitatively the experimental outcome. However, local plasma parameters—in particular when 3D distributions are of interest—can be difficult to determine from available diagnostics and so erosion / impurity transport modeling input relies on output from other codes and simplified models, increasing uncertainties in the outcome. In the present contribution, we introduce and evaluate the impact of improved models and parameters with largest uncertainties of processes that impact impurity production and transport across the scrape-off layer, when simulated in ERO: (i) the magnetic geometry has been revised, for affecting the separatrix position (located 50-60 mm away from limiter surface) and thus the background plasma profiles; (ii) connection lengths between components, which lead to shadowing of ion fluxes, are also affected by the magnetic configuration; (iii) anomalous transport of ionized impurities, defined by the perpendicular diffusion coefficient, has been revisited; (iv) erosion yields that account for energy and angular distributions of background plasma ions under the present enhanced sheath potential and oblique magnetic field, have been introduced; (v) the effect of additional erosion sources, such as charge-exchange neutral fluxes, which are dominant in recessed areas like antennas, has been evaluated; (vi) chemically assisted release of Be in molecular form has been included. Sensitivity analysis highlights a qualitative effect (i.e. change in emission patterns) of magnetic shadowing, anomalous diffusion, and inclusion of neutral fluxes and molecular release of Be. The separatrix location, and energy and angular distribution of background plasma fluxes impact erosion

Low plasma edge temperatures for the self-pumped limiter

International Nuclear Information System (INIS)

Terry, W.K.; Brooks, J.N.

1985-03-01

Transport code calculations have been performed to study the operation of an INTOR-like tokamak plasma from which helium is removed by a self-pumped limiter, which traps helium, but not hydrogen, in its surface layers. To prevent saturation by helium, the surface is renewed by continuous injection of the surface material (vanadium in this study) into the scrape-off layer. The presence of the injected vanadium leads to plasma temperatures well below 50 eV in the scrape-off layer, with supplementary rf heating. Operation in this edge temperature regime is essential for the use of medium- and high-Z limiter coatings

INVESTIGATION OF MAIN-CHAMBER AND DIVERTOR RECYCING IN DIII-D USING TANGENTIALLY VIEWING CID CAMERAS

International Nuclear Information System (INIS)

GROTH, M.; PORTER, G.D.; PETRIE, T.W.; FENSTERMACHER, M.E.; BROOKS, N.H.

2003-01-01

OAK-B135 Measurements of the D α emission profiles from the divertor and main chamber region in DIII-D, performed in low-density L-mode, and low and high-density ELMy H-mode plasmas imply that core plasma fueling occurs through the divertor channel. Emission profiles of carbon, combined with UEDGE modeling of the L-mode plasmas, also suggests that chemical sputtering of carbon from the flux surface adjacent to the inner divertor walls, and temperature gradient forces in the scrape-off layer, determine the carbon content of the inner scrape-off layer

Few-layer SnSe{sub 2} transistors with high on/off ratios

Energy Technology Data Exchange (ETDEWEB)

Pei, Tengfei; Bao, Lihong, E-mail: lhbao@iphy.ac.cn; Wang, Guocai; Ma, Ruisong; Yang, Haifang; Li, Junjie; Gu, Changzhi; Du, Shixuan; Gao, Hong-jun [Institute of Physics, Chinese Academy of Sciences, P. O. Box 603, Beijing 100190 (China); Pantelides, Sokrates [Department of Physics and Astronomy, Vanderbilt University, Nashville, Tennessee 37235 (United States); Material Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37381 (United States)

2016-02-01

We report few-layer SnSe{sub 2} field effect transistors (FETs) with high current on/off ratios. By trying different gate configurations, 300 nm SiO{sub 2} and 70 nm HfO{sub 2} as back gate only and 70 nm HfO{sub 2} as back gate combined with a top capping layer of polymer electrolyte, few-layer SnSe{sub 2} FET with a current on/off ratio of 10{sup 4} can be obtained. This provides a reliable solution for electrically modulating quasi-two-dimensional materials with high electron density (over 10{sup 13} cm{sup −2}) for field-effect transistor applications.

Radiation damage and redeposited-layer formation on plasma facing materials in the TRIAM-1M

International Nuclear Information System (INIS)

Hirai, Takeshi; Tokunaga, Kazutoshi; Fujiwara, Tadashi; Yoshida, Naoaki; Itoh, Satoshi

1997-01-01

As an aim to obtain some informations of material damage at long time discharge and redeposited-layer formed by scrape off layer (SOL), two collector probe experiments were conducted by using Tokamak of Research Institute for Applied Mechanics (TRIAM-IM). As a result, radiation damage due to charge exchange neutral particles of more than 2 MeV high energy component flying from plasma was observed. And in either experiment, redeposited-layer formation due to deposite of impurity atoms in the plasma could be observed. In the first experiment, a redeposited-layer with fine crystalline particles was observed, which was formed to contain multi-component system of Fe, Cr and Ni and light elements O and C. And, in the second experiment, a redeposited-layer grain-grown in which main component was Mo was observed. Surface modification of plasma facing material such as above-mentioned damage induction, redeposited-layer formation, and so on, was thought to much affect deterioration of materials and recycling of hydrogen. (G.K.)

ON Cone Bipolar Cell Axonal Synapses in the OFF Inner Plexiform Layer of the Rabbit Retina

Science.gov (United States)

Lauritzen, J. Scott; Anderson, James R.; Jones, Bryan W.; Watt, Carl B.; Mohammed, Shoeb; Hoang, John V.; Marc, Robert E.

2012-01-01

Analysis of the rabbit retinal connectome RC1 reveals that the division between the ON and OFF inner plexiform layer (IPL) is not structurally absolute. ON cone bipolar cells make non-canonical axonal synapses onto specific targets and receive amacrine cell synapses in the nominal OFF layer, creating novel motifs, including inhibitory crossover networks. Automated transmission electron microscope (ATEM) imaging, molecular tagging, tracing, and rendering of ≈ 400 bipolar cells reveals axonal ribbons in 36% of ON cone bipolar cells, throughout the OFF IPL. The targets include GABA-positive amacrine cells (γACs), glycine-positive amacrine cells (GACs) and ganglion cells. Most ON cone bipolar cell axonal contacts target GACs driven by OFF cone bipolar cells, forming new architectures for generating ON-OFF amacrine cells. Many of these ON-OFF GACs target ON cone bipolar cell axons, ON γACs and/or ON-OFF ganglion cells, representing widespread mechanisms for OFF to ON crossover inhibition. Other targets include OFF γACs presynaptic to OFF bipolar cells, forming γAC-mediated crossover motifs. ON cone bipolar cell axonal ribbons drive bistratified ON-OFF ganglion cells in the OFF layer and provide ON drive to polarity-appropriate targets such as bistratified diving ganglion cells (bsdGCs). The targeting precision of ON cone bipolar cell axonal synapses shows that this drive incidence is necessarily a joint distribution of cone bipolar cell axonal frequency and target cell trajectories through a given volume of the OFF layer. Such joint distribution sampling is likely common when targets are sparser than sources and when sources are coupled, as are ON cone bipolar cells. PMID:23042441

Reliable fabrication of plasmonic nanostructures without an adhesion layer using dry lift-off

Science.gov (United States)

Chen, Yiqin; Li, Zhiqin; Xiang, Quan; Wang, Yasi; Zhang, Zhiqiang; Duan, Huigao

2015-10-01

Lift-off is the most commonly used pattern-transfer method to define lithographic plasmonic metal nanostructures. A typical lift-off process is realized by dissolving patterned resists in solutions, which has the limits of low yield when not using adhesion layers and incompatibility with the fabrication of some specific structures and devices. In this work, we report an alternative ‘dry’ lift-off process to obtain metallic nanostructures via mechanical stripping by using the advantage of poor adhesion between resists and noble metal films. We show that this dry stripping lift-off method is effective for both positive- and negative-tone resists to fabricate sparse and densely-packed plasmonic nanostructures, respectively. In particular, this method is achieved without using an adhesion layer, which enables the mitigation of plasmon damping to obtain larger field enhancement. Dark-field scattering, one-photon luminescence and surface-enhanced Raman scattering measurements were performed to demonstrate the improved quality factor of the plasmonic nanostructures fabricated by this dry lift-off process.

Reliable fabrication of plasmonic nanostructures without an adhesion layer using dry lift-off

International Nuclear Information System (INIS)

Chen, Yiqin; Li, Zhiqin; Xiang, Quan; Wang, Yasi; Duan, Huigao; Zhang, Zhiqiang

2015-01-01

Lift-off is the most commonly used pattern-transfer method to define lithographic plasmonic metal nanostructures. A typical lift-off process is realized by dissolving patterned resists in solutions, which has the limits of low yield when not using adhesion layers and incompatibility with the fabrication of some specific structures and devices. In this work, we report an alternative ‘dry’ lift-off process to obtain metallic nanostructures via mechanical stripping by using the advantage of poor adhesion between resists and noble metal films. We show that this dry stripping lift-off method is effective for both positive- and negative-tone resists to fabricate sparse and densely-packed plasmonic nanostructures, respectively. In particular, this method is achieved without using an adhesion layer, which enables the mitigation of plasmon damping to obtain larger field enhancement. Dark-field scattering, one-photon luminescence and surface-enhanced Raman scattering measurements were performed to demonstrate the improved quality factor of the plasmonic nanostructures fabricated by this dry lift-off process. (paper)

EMC3-EIRENE modeling of toroidally-localized divertor gas injection experiments on Alcator C-Mod

Energy Technology Data Exchange (ETDEWEB)

Lore, J.D., E-mail: lorejd@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Reinke, M.L. [York Plasma Institute, Department of Physics, University of York, Heslington, York YO10 5DD (United Kingdom); LaBombard, B. [Plasma Science and Fusion Center, MIT, Cambridge, MA 02139 (United States); Lipschultz, B. [York Plasma Institute, Department of Physics, University of York, Heslington, York YO10 5DD (United Kingdom); Churchill, R.M. [Plasma Science and Fusion Center, MIT, Cambridge, MA 02139 (United States); Pitts, R.A. [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Feng, Y. [Max Planck Institute for Plasma Physics, Greifswald (Germany)

2015-08-15

Experiments on Alcator C-Mod with toroidally and poloidally localized divertor nitrogen injection have been modeled using the three-dimensional edge transport code EMC3-EIRENE to elucidate the mechanisms driving measured toroidal asymmetries. In these experiments five toroidally distributed gas injectors in the private flux region were sequentially activated in separate discharges resulting in clear evidence of toroidal asymmetries in radiated power and nitrogen line emission as well as a ∼50% toroidal modulation in electron pressure at the divertor target. The pressure modulation is qualitatively reproduced by the modeling, with the simulation yielding a toroidal asymmetry in the heat flow to the outer strike point. Toroidal variation in impurity line emission is qualitatively matched in the scrape-off layer above the strike point, however kinetic corrections and cross-field drifts are likely required to quantitatively reproduce impurity behavior in the private flux region and electron temperatures and densities directly in front of the target.

3D Scrape-off layer modelling with BoRiS

International Nuclear Information System (INIS)

Riemann, J.; Borchardt, M.; Schneider, R.; Mutzke, A.

2005-01-01

The 3D fluid transport code BoRiS is applied to a hydrogen plasma and a neutral fluid in a stellarator-like geometry equipped with a poloidal ring limiter. The results demonstrate the capability of dealing with 3D effects which can be related to both the influence of the geometry and the plasma-neutral interaction as well. The setup used has similarities with a poloidal gas target in a fusion device

Advanced metal lift-off process using electron-beam flood exposure of single-layer photoresist

Science.gov (United States)

Minter, Jason P.; Ross, Matthew F.; Livesay, William R.; Wong, Selmer S.; Narcy, Mark E.; Marlowe, Trey

1999-06-01

In the manufacture of many types of integrated circuit and thin film devices, it is desirable to use a lift-of process for the metallization step to avoid manufacturing problems encountered when creating metal interconnect structures using plasma etch. These problems include both metal adhesion and plasma etch difficulties. Key to the success of the lift-off process is the creation of a retrograde or undercut profile in the photoresists before the metal deposition step. Until now, lift-off processing has relied on costly multi-layer photoresists schemes, image reversal, and non-repeatable photoresist processes to obtain the desired lift-off profiles in patterned photoresist. This paper present a simple, repeatable process for creating robust, user-defined lift-off profiles in single layer photoresist using a non-thermal electron beam flood exposure. For this investigation, lift-off profiles created using electron beam flood exposure of many popular photoresists were evaluated. Results of lift-off profiles created in positive tone AZ7209 and ip3250 are presented here.

Observations on the scattering layers over the continental shelf off Konkan coast (India)

Digital Repository Service at National Institute of Oceanography (India)

RamaRaju, V.S.

The echograms obtained by R.V. "varuna" using asdic during the September, 1963 cruise are analysed. Scattering layers observed over the shelf area, off Ratnagiri, are examined and studied in relation to the thermocline layer present. Comparison...

Experimental validation of an analytical kinetic model for edge-localized modes in JET-ITER-like wall

Science.gov (United States)

Guillemaut, C.; Metzger, C.; Moulton, D.; Heinola, K.; O’Mullane, M.; Balboa, I.; Boom, J.; Matthews, G. F.; Silburn, S.; Solano, E. R.; contributors, JET

2018-06-01

The design and operation of future fusion devices relying on H-mode plasmas requires reliable modelling of edge-localized modes (ELMs) for precise prediction of divertor target conditions. An extensive experimental validation of simple analytical predictions of the time evolution of target plasma loads during ELMs has been carried out here in more than 70 JET-ITER-like wall H-mode experiments with a wide range of conditions. Comparisons of these analytical predictions with diagnostic measurements of target ion flux density, power density, impact energy and electron temperature during ELMs are presented in this paper and show excellent agreement. The analytical predictions tested here are made with the ‘free-streaming’ kinetic model (FSM) which describes ELMs as a quasi-neutral plasma bunch expanding along the magnetic field lines into the Scrape-Off Layer without collisions. Consequences of the FSM on energy reflection and deposition on divertor targets during ELMs are also discussed.

Scraping beam halo in {mu} {sup +} {mu} {sup minus} colliders

Energy Technology Data Exchange (ETDEWEB)

Drozhdin, A.; Mokhov, N.; Johnstone, C.; Wan, W.; Garren, A.

1998-01-01

Beam halo scraping schemes have been explored in the 50 x 50 GeV and 2 x 2 TeV {mu}{sup +}{mu}{sup -} colliders using both absorbers and electrostatic deflectors. Utility sections have been specially designed into the rings for scraping. Results of realistic STRUCT- MARS Monte-Carlo simulations show that for the low-energy machine a scheme with a 5 m long steel absorber suppresses losses in the interaction region by three orders of magnitude. The same scraping efficiency at 2 TeV is achieved only by complete extraction of beam halo from the machine. The effect of beam-induced power dissipation in the collider superconducting magnets and detector backgrounds is shown both for the first few turns after injection and for the rest of the cycle.

Localizing genes to cerebellar layers by classifying ISH images.

Directory of Open Access Journals (Sweden)

Lior Kirsch

Full Text Available Gene expression controls how the brain develops and functions. Understanding control processes in the brain is particularly hard since they involve numerous types of neurons and glia, and very little is known about which genes are expressed in which cells and brain layers. Here we describe an approach to detect genes whose expression is primarily localized to a specific brain layer and apply it to the mouse cerebellum. We learn typical spatial patterns of expression from a few markers that are known to be localized to specific layers, and use these patterns to predict localization for new genes. We analyze images of in-situ hybridization (ISH experiments, which we represent using histograms of local binary patterns (LBP and train image classifiers and gene classifiers for four layers of the cerebellum: the Purkinje, granular, molecular and white matter layer. On held-out data, the layer classifiers achieve accuracy above 94% (AUC by representing each image at multiple scales and by combining multiple image scores into a single gene-level decision. When applied to the full mouse genome, the classifiers predict specific layer localization for hundreds of new genes in the Purkinje and granular layers. Many genes localized to the Purkinje layer are likely to be expressed in astrocytes, and many others are involved in lipid metabolism, possibly due to the unusual size of Purkinje cells.

Double layer for hard spheres with an off-center charge

Directory of Open Access Journals (Sweden)

W. Silvestre-Alcantara

2016-02-01

Full Text Available Simulations for the density and potential profiles of the ions in the planar electrical double layer of a model electrolyte or an ionic liquid are reported. The ions of a real electrolyte or an ionic liquid are usually not spheres; in ionic liquids, the cations are molecular ions. In the past, this asymmetry has been modelled by considering spheres that are asymmetric in size and/or valence (viz., the primitive model or by dimer cations that are formed by tangentially touching spheres. In this paper we consider spherical ions that are asymmetric in size and mimic the asymmetrical shape through an off-center charge that is located away from the center of the cation spheres, while the anion charge is at the center of anion spheres. The various singlet density and potential profiles are compared to (i the dimer situation, that is, the constituent spheres of the dimer cation are tangentially tethered, and (ii the standard primitive model. The results reveal the double layer structure to be substantially impacted especially when the cation is the counterion. As well as being of intrinsic interest, this off-center charge model may be useful for theories that consider spherical models and introduce the off-center charge as a perturbation.

Radial convection of finite ion temperature, high amplitude plasma blobs

DEFF Research Database (Denmark)

Wiesenberger, M.; Madsen, Jens; Kendl, Alexander

2014-01-01

We present results from simulations of seeded blob convection in the scrape-off-layer of magnetically confined fusion plasmas. We consistently incorporate high fluctuation amplitude levels and finite Larmor radius (FLR) effects using a fully nonlinear global gyrofluid model. This is in line......-field transport compared to blobs simulated with the local model. The maximal blob amplitude is significantly higher in the global simulations than in the local ones. When the ion temperature is comparable to the electron temperature, global blob simulations show a reduced blob coherence and a decreased cross...

Two-zone model for the transport of wall released impurities in the edge plasma of a limiter tokamak

International Nuclear Information System (INIS)

Claassen, H.A.; Gerhauser, H.

1987-02-01

The transmission of a Gaussian metal impurity pulse uniformly injected from the torus wall is studied within a two-zone plasma model, which separates the plasma into scrape-off layer and plasma core and allows for discontinuous changes of the plasma parameters at the separatrix. The plasma parameters are supposed to ensure a collision dominated scrape-off plasma, in which case we may restrict the solution of the transport equations to its zero order approximation. (orig./GG)

SPS transverse beam scraping and LHC injection losses

CERN Document Server

Drosdal, L; Bartmann, W; Bracco, C; Cornelis, K; Goddard, B; Meddahi, M; Veyrunes, E

2012-01-01

Machine protection sets strict requirements for the quality of the injected beam, in particular in the transverse plane. Losses at aperture restrictions and protection elements have to be kept at a minimum. Particles in the beam tails are lost at the tight transfer line collimators and can trigger the LHC beam abort system. These particles have to be removed by scrapers in the vertical and horizontal plane in the SPS. Scraping has become vital for high intensity LHC operation. This paper shows the dependence of injection quality on the SPS scraping and discusses an improved scraper setting up strategy for better reproducibility with the current scraper system.

Modelling of radial electric field profile for different divertor configurations

International Nuclear Information System (INIS)

Rozhansky, V; Kaveeva, E; Voskoboynikov, S; Counsell, G; Kirk, A; Meyer, H; Coster, D; Conway, G; Schirmer, J; Schneider, R

2006-01-01

The impact of divertor configuration on the structure of the radial electric field has been simulated by the B2SOLPS5.0 transport fluid code. It is shown that the change in the parallel flows in the scrape-off layer, which are transported through the separatrix due to turbulent viscosity and diffusivity, should result in variation of the radial electric field and toroidal rotation in the separatrix vicinity. The modelling predictions are compared with the measurements of the radial electric field for the low field side equatorial mid-plane of ASDEX Upgrade in lower, upper and double-null (DN) divertor configurations. The parallel (toroidal) flows in the scrape-off layer and mechanisms for their formation are analysed for different geometries. It is demonstrated that a spike in the electric field exists at the high field side equatorial mid-plane in the connected DN divertor configuration. Its origin is connected with different potential drops between the separatrix vicinity and divertor plates in the two disconnected scrape-off layers, while the separatrix should be at almost the same potential. The spike might be important for additional turbulent suppression

Retinal layer measurements after successful macula-off retinal detachment repair using optical coherence tomography.

Science.gov (United States)

Menke, Marcel N; Kowal, Jens H; Dufour, Pascal; Wolf-Schnurrbusch, Ute E; Ceklic, Lala; Framme, Carsten; Wolf, Sebastian

2014-09-04

Optical coherence tomography (OCT) was used to analyze the thickness of various retinal layers of patients following successful macula-off retinal detachment (RD) repair. Optical coherence tomography scans of patients after successful macula-off RD repair were reanalyzed with a subsegmentation algorithm to measure various retinal layers. Regression analysis was performed to correlate time after surgery with changes in layer thickness. In addition, patients were divided in two groups. Group 1 had a follow-up period after surgery of up to 7 weeks (range, 21-49 days). In group 2, the follow-up period was >8 weeks (range, 60-438 days). Findings were compared to a group of age-matched healthy controls. Correlation analysis showed a significant positive correlation between inner nuclear-outer plexiform layer (INL-OPL) thickness and time after surgery (P=0.0212; r2=0.1551). Similar results were found for the ellipsoid zone-retinal pigment epithelium complex (EZ-RPE) thickness (P=0.005; r2=0.2215). Ganglion cell-inner plexiform layer thickness (GCL-IPL) was negatively correlated with time after surgery (P=0.0064; r2=0.2101). For group comparison, the retinal nerve fiber layer in both groups was thicker compared to controls. The GCL-IPL showed significant thinning in group 2. The outer nuclear layer was significantly thinner in groups 1 and 2 compared to controls. The EZ-RPE complex was significantly thinner in groups 1 and 2 compared to controls. In addition, values in group 1 were significantly thinner than in group 2. Optical coherence tomography retinal layer thickness measurements after successful macular-off RD repair revealed time-dependent thickness changes. Inner nuclear-outer plexiform layer thickness and EZ-RPE thickness was positively correlated with time after surgery. Ganglion cell-inner plexiform layer thickness was negatively correlated with time after surgery. Copyright 2014 The Association for Research in Vision and Ophthalmology, Inc.

Observational evidence of upwelling off the southwest coast of India during June-July 2006

Digital Repository Service at National Institute of Oceanography (India)

Lekshmi, S.; Smitha, B.R.; Revichandran, C.

transects off Thiruvananthapuram (8.5 degrees N) and off Koilam (9 degrees N), during June 25th-6th July 2006. Observed upwelling parameters (local temperature anomalies, salinity, isothermal layer depth (ILD), Mixed Layer Depth (MLD), isotherm slope...

Radial transport of poloidal momentum in ASDEX Upgrade in L-mode and H-mode

DEFF Research Database (Denmark)

Schrittwieser, R.; Mehlmann, F.; Naulin, Volker

2012-01-01

A reciprocating probe was used for localized measurements of the radial transport of poloidal momentum in the scrape-off layer (SOL) of ASDEX Upgrade (AUG). The probe measured poloidal and radial electric field components and density. We concentrate on three components of the momentum transport: ......: Reynolds stress, convective momentum flux and triple product of the fluctuating components of density, radial and poloidal electric field. For the evaluation we draw mainly on the probability density functions (PDFs)....

Weak localization in few-layer black phosphorus

International Nuclear Information System (INIS)

Du, Yuchen; Neal, Adam T; Zhou, Hong; Ye, Peide D

2016-01-01

We have conducted a comprehensive investigation into the magneto-transport properties of few-layer black phosphorus in terms of phase coherence length, phase coherence time, and mobility via weak localization measurement and Hall-effect measurement. We present magnetoresistance data showing the weak localization effect in bare p-type few-layer black phosphorus and reveal its strong dependence on temperature and carrier concentration. The measured weak localization agrees well with the Hikami–Larkin–Nagaoka model and the extracted phase coherence length of 104 nm at 350 mK, decreasing as ∼T −0.513+−0.053 with increased temperature. Weak localization measurement allows us to qualitatively probe the temperature-dependent phase coherence time τ ϕ , which is in agreement with the theory of carrier interaction in the diffusive regime. We also observe the universal conductance fluctuation phenomenon in few-layer black phosphorus within moderate magnetic field and low temperature regime. (paper)

Rotating liquid blanket for a toroidal fusion reator

International Nuclear Information System (INIS)

Moir, R.W.

1987-01-01

A novel blanket concept is presented for toroidal geometry in which many of the limitations imposed by a first wall are avoided by not having a first wall in the usual sense. The blanket consists of a rapidly rotating, low-vapor-pressure liquid that has a sharp boundary with the vacuum region. Nozzles inject ja continuous layer of cool liquid on the inner surface. The noncentricity of the plasma is maintained so that the plasma scrape-off region intersects the rotating liqid in a localized region. This noncentricity allows sufficient space so that the scrape-off plasma layer will not bombard the nozzles, whch penetrate through the rotating liquid. This liquid ''first wall'' is bombarded by the plasma, resulting in heat deposition, sputtering, and evaporation during the short time before the exposed liquid is covered by fresh, cool liquid from the nozzles. The advantages of this reactor concept appear to be very high wall loadings (speculated to be over 10 MW/m 2 ) and long component lifetime, both crucial economic factors. The nozzles are designed for easy replacement. The reactor's disatvantage is its enormous potential for plasma contamination by impurities. (orig.)

Investigation of self-organized criticality behavior of edge plasma transport in Torus experiment of technology oriented research

International Nuclear Information System (INIS)

Xu, Y.H.; Jachmich, S.; Weynants, R.R.; Huber, A.; Unterberg, B.; Samm, U.

2004-01-01

The self-organized criticality (SOC) behavior of the edge plasma transport has been studied using fluctuation data measured in the plasma edge and the scrape-off layer of Torus experiment of technology oriented research tokamak [H. Soltwisch et al., Plasma Phys. Controlled Fusion 26, 23 (1984)] before and during the edge biasing experiments. In the 'nonshear' discharge phase before biasing, the fluctuation data clearly show some of the characteristics associated with SOC, including similar frequency spectra to those obtained in 'sandpile' transport and other SOC systems, slowly decaying long tails in the autocorrelation function, values of Hurst parameters larger than 0.5 at all the detected radial locations, and a radial propagation of avalanchelike events in the edge plasma area. During the edge biasing phase, with the generation of an edge radial electric field E r and thus of E r xB flow shear, contrary to theoretical expectation, the Hurst parameters are substantially enhanced in the negative flow shear region and in the scrape-off layer as well. Concomitantly, it is found that the local turbulence is well decorrelated by the E r xB velocity shear, consistent with theoretical predictions

Ordinary mode reflectometry. Modification of the scattering and cut-off responses due to the shape of localized density fluctuations

International Nuclear Information System (INIS)

Fanack, C.; Boucher, I.; Heuraux, S.; Leclert, G.; Clairet, F.; Zou, X.L.

1996-01-01

Ordinary wave reflectometry in a plasma containing a localized density perturbation is studied with a 1-D model. The phase response is studied as a function of the wavenumber and position of the perturbation. It is shown that it strongly depends upon the perturbation shape and size. For a small perturbation wavenumber, the response is due to the oscillation of the cut-off layer. For larger wavenumbers, two regimes are found: for a broad perturbation, the phase response is an image of the perturbation itself; for a narrow perturbation, it is rather an image of the Fourier transform. For tokamak plasmas it turns out that, for the fluctuation spectra usually observed, the phase response comes primarily from those fluctuations that are localized at the cut-off. Results of a 2-D numerical model show that geometry effects are negligible for the scattering by radial fluctuations. (author)

Electron Bernstein Wave Research on CDX-U and NSTX

International Nuclear Information System (INIS)

Taylor, G.; Efthimion, P.C.; Jones, B.; Hosea, J.C.; Kaita, R.; LeBlanc, B.P.; Majeski, R.; Munsat, T.; Phillips, C.K.; Spaleta, J.; Wilson, J.R.; Rasmussen, D.; Bell, G.; Bigelow, T.S.; Carter, M.D.; Swain, D.W.; Wilgen, J.B.; Ram, A.K.; Bers, A.; Harvey, R.W.; Forest, C.B.

2001-01-01

Mode-converted electron Bernstein waves (EBWs) potentially allow the measurement of local electron temperature (Te) and the implementation of local heating and current drive in spherical torus (ST) devices, which are not directly accessible to low harmonic electron cyclotron waves. This paper reports on the measurement of X-mode radiation mode-converted from EBWs observed normal to the magnetic field on the midplane of the Current Drive Experiment-Upgrade (CDX-U) and the National Spherical Torus Experiment (NSTX) spherical torus plasmas. The radiation temperature of the EBW emission was compared to Te measured by Thomson scattering and Langmuir probes. EBW mode-conversion efficiencies of over 20% were measured on both CDX-U and NSTX. Sudden increases of mode-conversion efficiency, of over a factor of three, were observed at high-confinement-mode transitions on NSTX, when the measured edge density profile steepened. The EBW mode-conversion efficiency was found to depend on the density gradient at the mode-conversion layer in the plasma scrape-off, consistent with theoretical predictions. The EBW emission source was determined by a perturbation technique to be localized at the electron cyclotron resonance layer and was successfully used for radial transport studies. Recently, a new in-vessel antenna and Langmuir probe array were installed on CDX-U to better characterize and enhance the EBW mode-conversion process. The probe incorporates a local adjustable limiter to control and maximize the mode-conversion efficiency in front of the antenna by modifying the density profile in the plasma scrape-off where fundamental EBW mode conversion occurs. Initial results show that the mode-conversion efficiency can be increased to ∼100% when the local limiter is inserted near the mode-conversion layer. Plans for future EBW research, including EBW heating and current-drive studies, are discussed

Impact of E × B flow shear on turbulence and resulting power fall-off width in H-mode plasmas in experimental advanced superconducting tokamak

Energy Technology Data Exchange (ETDEWEB)

Yang, Q. Q., E-mail: yangqq@ipp.ac.cn; Zhong, F. C., E-mail: gsxu@ipp.ac.cn, E-mail: fczhong@dhu.edu.cn; Jia, M. N. [College of Science, Donghua University, Shanghai 201620 (China); Xu, G. S., E-mail: gsxu@ipp.ac.cn, E-mail: fczhong@dhu.edu.cn; Wang, L.; Wang, H. Q.; Chen, R.; Yan, N.; Liu, S. C.; Chen, L.; Li, Y. L.; Liu, J. B. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China)

2015-06-15

The power fall-off width in the H-mode scrape-off layer (SOL) in tokamaks shows a strong inverse dependence on the plasma current, which was noticed by both previous multi-machine scaling work [T. Eich et al., Nucl. Fusion 53, 093031 (2013)] and more recent work [L. Wang et al., Nucl. Fusion 54, 114002 (2014)] on the Experimental Advanced Superconducting Tokamak. To understand the underlying physics, probe measurements of three H-mode discharges with different plasma currents have been studied in this work. The results suggest that a higher plasma current is accompanied by a stronger E×B shear and a shorter radial correlation length of turbulence in the SOL, thus resulting in a narrower power fall-off width. A simple model has also been applied to demonstrate the suppression effect of E×B shear on turbulence in the SOL and shows relatively good agreement with the experimental observations.

Modeling of impurity spectroscopy in the divertor and SOL of DIII-D using the 1D multifluid model NEWT1D

International Nuclear Information System (INIS)

West, W.P.; Evans, T.E.; Brooks, N.H.

1996-10-01

NEWT1D, a one dimensional multifluid model of the scrape-off layer and divertor plasma, has been used to model the plasma including the distribution of carbon ionization states in the SOL and divertor of ELMing H-mode at two injected power levels in DIII-D. Comparison of the code predictions to the measured divertor and scrape-off layer (SOL) plasma density and temperature shows good agreement. Comparison of the predicted line emissions to the spectroscopic data suggests that physically sputtered carbon from the strike point is not transported up the flux tube; a distributed source of carbon a few centimeters up the flux tube is required to achieve reasonable agreement

Visible imaging of edge turbulence in NSTX

International Nuclear Information System (INIS)

Zweben, S.; Maqueda, R.; Hill, K.; Johnson, D.

2000-01-01

Edge plasma turbulence in tokamaks and stellarators is believed to cause the radical heat and particle flux across the separatrix and into the scrape-off-layers of these devices. This paper describes initial measurements of 2-D space-time structure of the edge density turbulence made using a visible imaging diagnostic in the National Spherical Torus Experiment (NSTX). The structure of the edge turbulence is most clearly visible using a method of gas puff imaging to locally illuminate the edge density turbulence

Visible imaging of edge turbulence in NSTX

International Nuclear Information System (INIS)

S. Zweben; R. Maqueda; K. Hill; D. Johnson; S. Kaye; H. Kugel; F. Levinton; R. Maingi; L. Roquemore; S. Sabbagh; G. Wurden

2000-01-01

Edge plasma turbulence in tokamaks and stellarators is believed to cause the radial heat and particle flux across the separatrix and into the scrape-off-layers of these devices. This paper describes initial measurements of 2-D space-time structure of the edge density turbulence made using a visible imaging diagnostic in the National Spherical Torus Experiment (NSTX). The structure of the edge turbulence is most clearly visible using a method of ''gas puff imaging'' to locally illuminate the edge density turbulence

Erosion and migration of tungsten employed at the central column heat shield of ASDEX Upgrade

International Nuclear Information System (INIS)

Krieger, K.; Gong, X.; Balden, M.; Hildebrandt, D.; Maier, H.; Rohde, V.; Roth, J.; Schneider, W.

2002-01-01

In ASDEX Upgrade, tungsten was employed as plasma facing material at the central column heat shield in the plasma main chamber. The campaign averaged tungsten erosion flux was determined by measuring the difference of the W-layer thickness before and after the experimental campaign using ion beam analysis methods. The observed lateral variation and the total amount of eroded tungsten are attributed to erosion by impact of ions from the scrape-off layer plasma. Migration and redeposition of eroded tungsten were investigated by quantitative analysis of deposited tungsten on collector probes and wall samples. The obtained results, as well as the spectroscopically observed low tungsten plasma penetration probability, indicate that a major fraction of the eroded tungsten migrates predominantly through direct transport channels in the outer plasma scrape-off layer without entering the confined plasma

Catastrophe in the stochastic layer due to dipole perturbation for a single-null divertor Tokamak

International Nuclear Information System (INIS)

Ali, H.; Watson, M.; Punjabi, A.; Boozer, A.

1996-01-01

We use the method of maps developed by Punjabi and Boozer to investigate the motion of magnetic field lines in stochastic scrape-off layer in the presence of dipole perturbation of a single-null divertor Tokamak. This method is based on the idea that the magnetic field line trajectories in a divertor tokamak are mathematically equivalent to a single degree of freedom, time dependent Hamiltonian System, and that the basic features of motion near a separatrix broadened by asymmetric perturbations are generic for such Hamiltonian and near-Hamiltonian systems. The magnetic topology of a single-null divertor tokamak with the effects on dipole perturbations is represented by the Symmetric Simple Map followed by Dipole Map. We have found that as the amplitude of the dipole perturbation increases, the width of the stochastic layer also increases. At some critical value of the amplitude is reached, there is a catastrophic increase in the width of stochastic layer. This may have significant implications for tokamak divertor physics

Properties of the TEXTOR boundary layer

International Nuclear Information System (INIS)

Bogen, P.; Hartwig, H.; Hintz, E.; Hoethker, K.; Lie, Y.T.; Pospieszczyk, A.; Samm, U.

1984-01-01

First measurements on the TEXTOR boundary layer are reported. The hydrogen recycling in front of the four limiter segments has been studied by means of a CCD-camera, which proved to be a good instrument to center the discharge for symmetric plasma-limiter contact. The composition of the neutral fluxes from the limiter have been measured: oxygen fluxes are about a factor of ten higher than the metal fluxes; within the error limits the composition does not change with varying limiter radius. Electron densities in the scrape-off layer away from the limiter have been determined by injecting an Li-atom beam from a thermal source and by observing its emission as a function of radius. Similar measurements have been made in front of the limiter with sputtered Cr and O atoms. Both methods gave for the magnetic surface of the limiter radius nsub(e) approx.= 1 x 10 12 /cm 23 . Infrared observations of a test limiter with a CCD-camera and a PbSe-detector have been performed to record the thermal loads. About 10% of the input power flows to the limiter. (orig.)

Multi-code analysis of scrape-off layer filament dynamics in MAST

DEFF Research Database (Denmark)

Militello, F.; Walkden, N. R.; Farley, T.

2016-01-01

velocities of the order of 1 km s(-1), a perpendicular diameter of around 2-3 cm and a density amplitude 2-3.5 times the background plasma. 3D and 2D numerical codes (the STORM module of BOUT++, GBS, HESEL and TOKAM3X) are used to reproduce the motion of the observed filaments with the purpose of validating...

Scrape-off layer power flux measurements in the Tore Supra tokamak

Czech Academy of Sciences Publication Activity Database

Gunn, J. P.; Dejarnac, Renaud; Devynck, P.; Fedorczak, N.; Fuchs, Vladimír; Gil, C.; Kočan, M.; Komm, Michael; Kubič, M.; Lunt, T.; Monier-Garbet, P.; Pascal, J.-Y.; Saint-Laurent, F.

2013-01-01

Roč. 438, suppl (2013), S184-S188 ISSN 0022-3115. [International Conference on Plasma-Surface Interactions in Controlled Fusion Devices/20./. Aachen, 21.05.2012-25.05.2012] Institutional support: RVO:61389021 Keywords : plasma * tokamak Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.016, year: 2013 http://www.sciencedirect.com/science/article/pii/S0022311513000639#

Three dimensional simulations of plasma filaments in the scrape off layer

DEFF Research Database (Denmark)

Easy, L.; Militello, F.; Omotani, J.

2014-01-01

closure was found to not replicate the 3D perpendicular dynamics and overestimated the initial radial acceleration of all the filaments studied. In contrast, a more satisfactory comparison with the sheath dissipation closure was obtained, even in the presence of significant parallel gradients, where...

Narrow heat flux channels in the COMPASS limiter scrape-off layer

Czech Academy of Sciences Publication Activity Database

Horáček, Jan; Vondráček, Petr; Pánek, Radomír; Dejarnac, Renaud; Komm, Michael; Pitts, R.A.; Kocan, M.; Goldston, R.J.; Stangeby, P.C.; Gauthier, E.; Háček, Pavel; Havlíček, Josef; Hron, Martin; Imríšek, Martin; Janky, Filip; Seidl, Jakub

2015-01-01

Roč. 463, August (2015), s. 385-388 ISSN 0022-3115. [PLASMA-SURFACE INTERACTIONS 21: International Conference on Plasma-Surface Interactions in Controlled Fusion Devices. Kanazawa, 26.05.2014-30.05.2014] R&D Projects: GA ČR(CZ) GAP205/12/2327; GA MŠk(CZ) LM2011021 Institutional support: RVO:61389021 Keywords : plasma * tokamak * COMPASS Subject RIV: JF - Nuclear Energetics OBOR OECD: Nuclear related engineering Impact factor: 2.199, year: 2015 http://www.sciencedirect.com/science/article/pii/S0022311514009398

Statistical analysis of turbulent front propagation in the scrape-off-layer

International Nuclear Information System (INIS)

Ghendrih, Ph.; Sarazin, Y.; Attuel, G.; Benkadda, S.; Beyer, P.; Darmet, G.; Falchetto, G.; Figarella, C.; Garbet, X.; Grandgirard, V.; Ottaviani, M.

2005-01-01

The intermittent transport in the SOL is analysed in terms of the interaction between the average profile and the population of large transport events, the fronts. This provides the basis for the statistical analysis presented in this paper. Data from 2D numerical simulations is analysed here. The mean density e-folding length for the fronts is observed to be the same as that of the time average profile. The mean ballistic velocity of the fronts has a radial Mach number of 0.03. A symmetric distribution of poloidal Mach numbers is found, its width is comparable to that of the radial Mach number, ΔM ∼ 0.02. The small fronts are found to be isotropic, the larger fronts are elongated radially (aspect ratio ∼ 6). A characteristic poloidal scale is found, typically 7 Larmor radii

Local charge measurement using off-axis electron holography

DEFF Research Database (Denmark)

Beleggia, Marco; Gontard, L.C.; Dunin-Borkowski, R.0E.

2016-01-01

A model-independent approach based on Gauss’ theorem for measuring the local charge in a specimen from an electron-optical phase image recorded using off-axis electron holography was recently proposed. Here, we show that such a charge measurement is reliable when it is applied to determine the to...

Flux and fluence determination using the material scrapings approach

International Nuclear Information System (INIS)

Basha, H.S.; Manahan, M.P.

1992-01-01

The conventional approach to flux determination is to use high-purity dosimeters to characterize the neutron field. This paper presents an alternative approach called the scraping method. This method consists of taking scraping samples from an in-service component and using this material to measure the specific activity for various reactions. This approach enables the determination of the neutron flux and fluence incident on any component for which small chips of material can be safely obtained. It offers a capability for determining the neutron flux for components such as reactor internals without destructively removing them from service. The scrapings methodology was benchmarked by comparison with the results obtained using conventional dosimetry data from the San Onofre nuclear generation station Unit 2 (SONGS-2). Additionally, since the goal of any reactor physics analysis is to reduce uncertainty to the extent practical, it is important that the best available cross-section library be used. The fast flux calculated-to-experimental (C/E) ratios at the SONGS-297-deg in-vessel surveillance capsule and the REACTOR-X 90-deg ex-vessel dosimetry positions were studied for several cross-section libraries, including BIGLE-80, SAILOR, and ELXSIR. REACTOR-X is a pressurized water reactor power plant currently operating in the US

Study on the vibrational scraping of uranium product from a solid cathode of electrorefiner

Energy Technology Data Exchange (ETDEWEB)

Park, Sung Bin; Kang, Young Ho; Hwang, Sung Chan; Lee, Han Soo; Paek, Seung Woo; Ahn, Do Hee [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-12-15

A high-throughput electrorefiner has been developed for commercialization use by enhancing the uranium recovery from the reduced metal which is produced from the oxide reduction process. It is necessary to scrap and effectively collect uranium dendrites from the surface of the solid cathode for high yield. When a steel electrode is used as the cathode in the electrorefining process, uranium is deposited and regularly stuck to the steel cathode during electrorefining. The sticking coefficient of a steel cathode is very high. In order to decrease the sticking coefficient of the steel cathode effectively, vibration mode was applied to the electrode in this study. Uranium dendrites were scraped and fell apart from the steel cathode by a vibration force. The vibrational scraping of the steel cathode was compared to the self-scraping of the graphite cathode. Effects of the applied current density and the vibration stroke on the scraping of the uranium dendrites were also investigated.

Recombination region improvement for reduced efficiency roll-off in phosphorescent OLEDs with dual emissive layers

Energy Technology Data Exchange (ETDEWEB)

Ma, Zhu; Zhou, Shunliang [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Hu, Song [Chengdu Institute of Optics and Electronics, Chinese Academy of Sciences, Chengdu 610209 (China); Yu, Junsheng, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2014-10-15

High-performance phosphorescent organic light-emitting diodes (PhOLEDs) by using dual-emissive-layer (DEL) structure to reduce efficiency roll-off were fabricated. The DEL was comprised of a hole-transport-type host of N, N′-bis(naphthalen-1-yl)-N, N′-bis(phenyl)-benzidine (NPB) and a bipolar host of 4,4′-bis(carbazol-9-yl)biphenyl (CBP), which were both doped with an orange phosphorescent dopant of bis[2-(4-tert-butylphenyl)-benzothiazolato-N,C2′]iridium (acetylacetonate) [(t-bt){sub 2}Ir(acac)]. After the optimization of doping concentration of the first emissive layer (FEL), the device with DEL exhibited 11% lower roll-off power efficiency than single emissive layer devices (SED) when the luminance increased from 1000 cd/m{sup 2} to 10,000 cd/m{sup 2}. The hole–electron recombination zone in DEL was illuminated by inserting an ultrathin fluorescent probe of 4-(dicyanomethylene)-2-tert-butyl-6 (1,1,7,7-tetramethyljulolidin-4-yl-vinyl)-4H-pyran (DCJTB) in different emissive regions. The performance improvement was attributed to the optimization of energy barrier and the expansion of exciton formation zone within the DEL. - Highlights: • PhOLEDs by using a dual-emissive-layer structure to reduce efficiency roll-off were fabricated. • The DED exhibited 11% lower efficiency roll-off, 57% lower turn-on voltage, and 174% higher brightness than SED. • A DCJTB fluorescent probe was inserted at different positions of DED to investigate the expansion of exciton formation zone.

Observation of Blobs and Holes in the Boundary Plasma of EAST Tokamak

DEFF Research Database (Denmark)

Yan, Ning; Xu, Guosheng; Zhang, Wei

2011-01-01

Intermittent convective transport at the edge and in the scrape-off layer (SOL) of EAST was investigated by using fast reciprocating Langmuir probe. Holes, as part of plasma structures, were detected for the first time inside the shear layer. The amplitude probability distribution function...

Challenges in edge modeling

International Nuclear Information System (INIS)

Schneider, R.

2007-01-01

Fluid models like B2, UEDGE or EDGE2D are the working horses for scrape-off layer physics, both for design and experimental support. The concept of a numerical tokamak, aiming at a predictive code for ITER, triggers the need to re-assess the available tools and their necessary extensions. These additional physics issues will be summarized from a personal point-of-view. Depending on the specific problem, several complexity levels of scrape-off layer models will be needed. Therefore, a hierarchy of tools is necessary, which will be discussed. Furthermore, the experience existing in other scientific fields with multi-scale problems and modeling should be used. Here, the coupling of different length and time scales are in particular of interest for fusion problems. (author)

Transport and re-deposition of limiter-released metal impurities

International Nuclear Information System (INIS)

Claasen, H.A.; Repp, H.

1983-01-01

The transport parallel B-vector and re-deposition of limiter- (or divertor-target-)released metal impurities in a given counter-streaming scrape-off layer plasma is studied analytically by using a kinetic approach. Electron impact ionization, Coulomb collisions with the hydrogen ions, and impurity ion acceleration in a pre-sheath electric field are accounted for. The friction and electric-field forces provide the driving forces for impurity re-cycling in front of the limiter. Both hydrogen ion sputtering and self-sputtering are included (the latter for impurity emission perpendicular to the limiter surface). The analytical formulas are numerically evaluated for the example of sputtered iron impurities, assuming a simple model for a scrape-off layer plasma in contact with a stainless-steel poloidal ring limiter. (author)

Beam Scraping for LHC Injection

CERN Document Server

Burkhardt, H; Fischer, C; Gras, J-J; Koschik, A; Kramer, Daniel; Pedersen, S; Redaelli, S

2007-01-01

Operation of the LHC will require injection of very high intensity beams from the SPS to the LHC. Fast scrapers have been installed and will be used in the SPS to detect and remove any existing halo before beams are extracted, to minimize the probability for quenching of superconducting magnets at injection in the LHC. We briefly review the functionality of the scraper system and report about measurements that have recently been performed in the SPS on halo scraping and re-population of tails.

Localization for off-diagonal disorder and for continuous Schroedinger operators

International Nuclear Information System (INIS)

Delyon, F.; Souillard, B.; Simon, B.

1987-01-01

We extend the proof of localization by Delyon, Levy, and Souillard to accommodate the Anderson model with off-diagonal disorder and the continuous Schroedinger equation with a random potential. (orig.)

Double layer resist process scheme for metal lift-off with application in inductive heating of microstructures

DEFF Research Database (Denmark)

Ouattara, Lassana; Knutzen, Michael; Keller, Stephan Urs

2010-01-01

We present a new method to define metal electrodes on top of high-aspect-ratio microstructures using standard photolithography equipment and a single chromium mask. A lift-off resist (LOR) layer is implemented in an SU-8 photolithography process to selectively remove metal at the end of the proce......We present a new method to define metal electrodes on top of high-aspect-ratio microstructures using standard photolithography equipment and a single chromium mask. A lift-off resist (LOR) layer is implemented in an SU-8 photolithography process to selectively remove metal at the end...

Evidence for a poloidally localized enhancement of radial transport in the scrape-off layer of the Tore Supra tokamak

Czech Academy of Sciences Publication Activity Database

Gunn, J. P.; Boucher, C.; Dionne, M.; Ďuran, Ivan; Fuchs, Vladimír; Loarer, T.; Nanobashvili, I.; Pánek, Radomír; Pascal, J.-Y.; Saint-Laurent, F.; Stöckel, Jan; Van Rompuy, T.; Zagórski, R.; Adámek, Jiří; Bucalossi, J.; Dejarnac, Renaud; Devynck, P.; Hertout, P.; Hron, Martin; Lebrun, G.; Moreau, P.; Rimini, F.; Sarkissian, A.; Van Oost, G.

363-365, - (2007), s. 484-490 ISSN 0022-3115. [International Conference on Plasma-Surface Interactions in Controlled Fusion Devices/17th./. Hefei, 22.05.2006-26.05. 2006] R&D Projects: GA ČR GP202/03/P062 Institutional research plan: CEZ:AV0Z20430508 Keywords : Cross-field transport * Edge plasma * Plasma flow * Tore Supra Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 1.643, year: 2007

Beam Scraping in the SPS for LHC Injection Efficiency and Robustness Studies

CERN Document Server

Letnes, Paul/LPA; Myrheim, Jan

2008-01-01

The Large Hadron Collider (LHC) at CERN will be the world's most powerful accelerator when it is commissioned in fall 2008. Operation of the LHC will require injection of very high intensity beams. Fast transverse beam scrapers have been installed in the Super Proton Synchrotron (SPS) injector to detect and, if necessary, remove transverse beam tails. This will help to both diagnose and prevent beam quenches in the LHC. Scraping of a high intensity beam at top energy can potentially damage the scraper jaws. This has been studied with Monte Carlo simulations to find energy deposition and limits for hardware damage. Loss maps from scraping have been generated both with machine studies and tracking simulations. Time dependent Beam Loss Monitor (BLM) measurements have shown several interesting details about the beam. An analytical model of time dependent losses is compared with beam measurements and demonstrates that beam scraping can be used to estimate the beam size. Energy deposition simulations also give the ...

Role of scrape cytology in the intraoperative diagnosis of tumor

Directory of Open Access Journals (Sweden)

Kolte Sachin

2010-01-01

Full Text Available Background : Rapid diagnosis of surgically removed specimens has created many controversies and a single completely reliable method has not yet been developed. Histopathology of a paraffin section remains the ultimate gold standard in tissue diagnosis. Frozen section is routinely used by the surgical pathology laboratories for intraoperative diagnosis. The use of either frozen section or cytological examination alone has an acceptable rate (93-97% of correct diagnosis, with regard to interpretation of benign versus malignant. Aim : To evaluate the utility of scrape cytology for the rapid diagnosis of surgically removed tumors and its utilisation for learning cytopathology. Materials and Methods : 75 surgically removed specimens from various organs and systems were studied. Scrapings were taken from each specimen before formalin fixation and stained by modified rapid Papanicolaou staining. Results : Of the 75 cases studied, 73 could be correctly differentiated into benign and malignant tumors, with an accuracy rate of 97.3%. Conclusions : Intraoperative scrape cytology is useful for intraoperative diagnosis of tumor, where facilities for frozen section are not available. The skill and expertise developed by routinely practicing intraoperative cytology can be applied to the interpretation of fine needle aspirate smears. Thus, apart from its diagnostic role, intraoperative cytology can become a very useful learning tool in the field of cytopathology.

Impurity transport calculations for the limiter shadow region of a tokamak

International Nuclear Information System (INIS)

Claassen, H.A.; Repp, H.

1981-01-01

Impurity transport calculations are presented for the scrape-off layer of a tokamak with a poloidal ring limiter. The theory is based on the drift-kinetic equations for the impurity ions in their different ionization states. It is developed in the limit of low impurity concentrations under due consideration of electron impact ionization, Coulomb collisions with hydrogen ions streaming onto a neutralizing surface, a convection along the magnetic field, and a radial drift. The background plasma and the impurity sources at the walls enter the theory as input parameters. Numerical results are given for the radial profiles of density, temperature, particle flux, and energy flux of wall-released impurity ions as well as for the screening efficiency of the scrape-off layer neglecting impurity re-emission from the limiter. (author)

Mitigating impact of thermal and rectified radio-frequency sheath potentials on edge localized modes

Energy Technology Data Exchange (ETDEWEB)

Gui, B. [Institute of Plasma Physics Chinese Academy of Sciences, Hefei (China); Lawerence Livermore National Lab, Livermore, California 94550 (United States); Xu, X. Q. [Lawerence Livermore National Lab, Livermore, California 94550 (United States); Myra, J. R.; D' Ippolito, D. A. [Lodestar Research Corporation, Boulder, Colorado 80301 (United States)

2014-11-15

The mitigating impact of thermal and rectified radio frequency (RF) sheath potentials on the peeling-ballooning modes is studied non-linearly by employing a two-fluid three-field simulation model based on the BOUT++ framework. Additional shear flow and the Kelvin-Helmholtz effect due to the thermal and rectified RF sheath potential are induced. It is found that the shear flow increases the growth rate while the K-H effect decreases the growth rate slightly when there is a density gradient, but the energy loss of these cases is suppressed in the nonlinear phase. The stronger external electrostatic field due to the sheaths has a more significant effect on the energy loss suppression. From this study, it is found the growth rate in the linear phase mainly determines the onset of edge-localized modes, while the mode spectrum width in the nonlinear phase has an important impact on the turbulent transport. The wider mode spectrum leads to weaker turbulent transport and results in a smaller energy loss. Due to the thermal sheath and rectified RF sheath potential in the scrape-off-layer, the modified shear flow tears apart the peeling-ballooning filament and makes the mode spectrum wider, resulting in less energy loss. The perturbed electric potential and the parallel current near the sheath region is also suppressed locally due to the sheath boundary condition.

Strain-free GaN thick films grown on single crystalline ZnO buffer layer with in situ lift-off technique

International Nuclear Information System (INIS)

Lee, S. W.; Minegishi, T.; Lee, W. H.; Goto, H.; Lee, H. J.; Lee, S. H.; Lee, Hyo-Jong; Ha, J. S.; Goto, T.; Hanada, T.; Cho, M. W.; Yao, T.

2007-01-01

Strain-free freestanding GaN layers were prepared by in situ lift-off process using a ZnO buffer as a sacrificing layer. Thin Zn-polar ZnO layers were deposited on c-plane sapphire substrates, which was followed by the growth of Ga-polar GaN layers both by molecular beam epitaxy (MBE). The MBE-grown GaN layer acted as a protecting layer against decomposition of the ZnO layer and as a seeding layer for GaN growth. The ZnO layer was completely in situ etched off during growth of thick GaN layers at low temperature by hydride vapor phase epitaxy. Hence freestanding GaN layers were obtained for the consecutive growth of high-temperature GaN thick layers. The lattice constants of freestanding GaN agree with those of strain-free GaN bulk. Extensive microphotoluminescence study indicates that strain-free states extend throughout the high-temperature grown GaN layers

Comparison of acetate tape impression with squeezing versus skin scraping for the diagnosis of canine demodicosis.

Science.gov (United States)

Pereira, A V; Pereira, S A; Gremião, I D F; Campos, M P; Ferreira, A M R

2012-11-01

This study compared the sensitivity of acetate tape impression and skin squeezing with that of deep skin scraping for the diagnosis of demodicosis in dogs. Demodex canis was detected in 100% of acetate tape impressions obtained after skin squeezing and in 90% of deep skin scrapings. There was a significant difference (P < 0.001) between the techniques in the total number of mites detected. Acetate tape impression with skin squeezing was found to be more sensitive than deep skin scraping and is an alternative diagnostic method for canine demodicosis. © 2012 The Authors. Australian Veterinary Journal © 2012 Australian Veterinary Association.

Collection of preputial material by scraping and aspiration for the diagnosis of Tritrichomonas foetus in bulls

Directory of Open Access Journals (Sweden)

P.C. Irons

2002-07-01

Full Text Available Two trials were carried out to assess the diagnostic sensitivity and practicability of preputial scraping as a method of collecting preputial material from bulls infected with Tritrichomonas foetus. In the 1st trial, preputial material was collected by simultaneous scraping and aspiration from 3 infected and 1 uninfected bull 10 times over a 5-week period. In the 2nd trial, samples from 5 infected bulls were collected by both sheath washing and scraping on 6 occasions, while 8 uninfected animals were sampled 3 times. Samples were cultured using a modified Trichomonas culture medium (Oxoid. In the first trial, 29 of 30 samples from infected bulls were found to be positive. In the second trial, 83 % of samples collected by both methods tested positive. In neither trial were any samples from the control bulls found to be positive. Scraping was found to be quick and safe, and offered advantages over preputial washing in that urine contamination was easily avoided, samples were smaller and more concentrated and contamination was reduced. It may, however, be subject to greater operator variability than sheath washing. It is concluded that preputial scraping is as effective as washing and represents a suitable alternative for the collection of material for direct examination and culture of Tritrichomonas foetus.

Scrape-off model and pumped-limiter design for reversed-field pinches (RFP)

International Nuclear Information System (INIS)

Embrechts, M.J.; Bathke, C.G.; Krakowski, R.A.

1983-01-01

In order to develop a better understanding of the plasma/first-wall interaction in an RFP configuration, the models being developed to describe edgeplasma and scrapeoff regions for the tokamak have been adopted. Specifically, a scrapeoff model similar to the one developed and used for the tokamak FED design is used to model the parameter range where pumped limiters may be applied to the compact RFP. The one-dimensional, steady-state heat and particle equations are solved in the scrapeoff layer for an RFP geometry, assuming equal electron and ion temperature and density, convective transport along field lines, and Bohm-like diffusion. All charge-exchange and radiation effects are assumed to take place in the region between plasma and scrapeoff layer, and only a specific fraction of the total plasma energy will enter the scrapeoff layer in the form of conduction and convection. A simplified recycling model based on an effective recycling coefficient is used. For a given particle and energy flux entering the scrapeoff and for specified relationships between the particle flux and the energy flux near the first wall, the temperature and density profiles in the scrapeoff layer region are determined. The shape of the limiter surface is determined iteratively for a specified number of poloidal limiters by specifying a constant (design) heat flux for the limiter surfaces

The influence of blobs on neutral particles in the scrape-off layer

DEFF Research Database (Denmark)

Thrysøe, Alexander Simon; Tophøj, Laust Emil Hjerrild; Naulin, Volker

2016-01-01

and edge are investigated. Simulations suggest that neutrals originating from dissociation of hydrogen molecules only fuel in the outermost edge region of the plasma, whereas hot neutrals from charge exchange collisions penetrate deep into the bulk plasma. The results are recovered in a simplified 2D model....

Analysis of plasma flow in a scrape-off layer in a tokamak

International Nuclear Information System (INIS)

Petrov, V.G.

1988-01-01

Plasma drift on the periphery of a tokamak in a magnetic tube, on sides of which coins are placed, is considered. Convection caused by toroidal particle drift is taken into account. Distribution of plasma parameters in such a tube is found. Transition from the total poloidal diaphragm to a sectioned one is traced

Kinetic simulations of scrape-off layer physics in the DIII-D tokamak

Directory of Open Access Journals (Sweden)

R.M. Churchill

2017-08-01

The XGCa simulation of the DIII-D tokamak in a nominally sheath-limited regime show many noteworthy features in the SOL. The density and ion temperature are higher at the low-field side, indicative of ion orbit loss. The SOL ion Mach flows are at experimentally relevant levels (Mi ∼ 0.5, with similar shapes and poloidal variation as observed in various tokamaks. Surprisingly, the ion Mach flows close to the sheath edge remain subsonic, in contrast to the typical fluid Bohm criterion requiring ion flows to be above sonic at the sheath edge. Related to this are the presence of elevated sheath potentials, eΔΦ/Te∼3−4, over most of the SOL, with regions in the near-SOL close to the separatrix having eΔΦ/Te > 4. These two results at the sheath edge are a consequence of non-Maxwellian features in the ions and electrons there.

ITER EDA newsletter. V. 9, no. 2

International Nuclear Information System (INIS)

2000-02-01

This ITER EDA Newsletter reports on the seventh ITER technical meeting on safety and environment and contains the executive summary of the eleventh ITER scrape-off layer and divertor physics expert group meeting. Individual abstracts have been prepared

Observation of self-organized criticality (SOC) behavior during edge biasing experiment on TEXTOR

Energy Technology Data Exchange (ETDEWEB)

Xu, Y.H.; Jachmich, S.; Weynants, R.R. [Ecole Royale Militaire/Koninklijke Militaire School, Laboratory for Plasma Physics, Euratom-Belgian State Association, Brussels, Belgium, Partner in the Trilateral Euregio Cluster (Belgium)

2004-07-01

The self-organized criticality (SOC) behavior of the edge plasma transport has been investigated using the fluctuation data measured in the plasma edge and the scrape-off layer of TEXTOR tokamak before and during the edge electrode biasing experiments. In the 'non-shear' discharge phase before biasing, both the potential and density fluctuations clearly exhibit some of the characteristics associated with SOC: (1) existence of f{sup -1} power-law dependence in the frequency spectrum, (2) slowly decaying long tails in the autocorrelation function, (3) values of Hurst parameters larger than 0.5 at all the detected radial locations, (4) non-Gaussian probability density function of fluctuations and (5) radial propagation of avalanche-like events in the edge plasma area. During the biasing phase, with the generation of an edge radial electric field E{sub r} and hence a sheared E{sub r} x B flow, the local turbulence is found to be well de-correlated by the E{sub r} x B velocity shear, consistent with theoretical predictions. Nevertheless, it is concomitantly found that the Hurst parameters are substantially enhanced in the negative flow shear region and in the scrape-off layer as well, which is contrary to theoretical expectation. Implication of these observations to our understanding of plasma transport mechanisms is discussed. (authors)

Applications of the oral scraped (exfoliative) cytology in oral cancer and precancer.

Science.gov (United States)

Acha, Amelia; Ruesga, María T; Rodríguez, María J; Martínez de Pancorbo, María A; Aguirre, José M

2005-01-01

Scraped (exfoliative) cytology is a simple and harmless procedure, which has been a controversial technique according to its real validity in oral pathology. Lately it has re-emerged due to its application in oral precancer and cancer as a diagnostic and predictive method as well as for monitoring patients. New diagnostic techniques have been developed, such as "brush biopsy" and multiple molecular studies using the cells collected. In this review we are going to analyse the more novel aspects related with the applications of the scraped or exfoliative cytology in oral precancerous and cancerous pathology, specially focusing on molecular studies and their diagnostic and prognostic implications.

Statistical characterization of turbulence in the boundary plasma of EAST

DEFF Research Database (Denmark)

Yan, Ning; Nielsen, Anders Henry; Xu, G.S.

2013-01-01

In Ohmic heated low confinement mode (L-mode) discharges, the intermittent statistical characteristics of turbulent fluctuations have been investigated in the edge and the scrape-off layer (SOL) plasma on EAST (the experimental advanced superconducting tokamak) by fast reciprocating Langmuir probe...

Extensive jaw mobility in suckermouth armored catfishes (Loricariidae): a morphological and kinematic analysis of substrate scraping mode of feeding.

Science.gov (United States)

Adriaens, Dominique; Geerinckx, Tom; Vlassenbroeck, Jelle; Van Hoorebeke, Luc; Herrel, Anthony

2009-01-01

Loricariidae, or suckermouth armored catfishes, possess upper and lower jaws that are ventrally oriented and that bear teeth that touch the substrate from which algae and other food items are scraped. The ventral orientation and the highly specialized morphology of the jaws, characterized by protrusible upper jaws and left-right decoupled lower jaws, are observed in Pterygoplichthys disjunctivus, the species investigated here. Kinematic data of the scraping feeding movements, obtained by external high-speed and x-ray recordings, are used to quantify jaw movement, especially to test for upper jaw mobility and versatility during substrate scraping. Our results show that the mobility of the jaws is indeed high compared with what is standard for catfishes. The upper jaw's ability to perform a substantial degree of rostrocaudal movement is quite unique for catfishes. The ventromedially oriented lower jaws, with the teeth and the coronoid process at opposite sides, display an extensive mobility: they rotate around the suspensorial articulation and around their longitudinal axis, resulting in an extended scraping movement and thereby covering a large surface area. The lower jaws also show a left-right asymmetry in their movements during scraping. Thus, our results suggest that the extreme morphological specializations of the jaws in loricariid catfishes are linked to an increased mobility and functional versatility, allowing these animals to efficiently scrape algae from substrates with irregular surfaces.

A helical magnetic limiter for boundary layer control in large tokamaks

International Nuclear Information System (INIS)

Feneberg, W.; Wolf, G.H.

1981-01-01

In a tokamak configuration, superposition of the magnetic field of resonant helical windings which surround the toroidal plasma current outside the first wall destroys the magnetic surfaces in the boundary layer (ergodization). A transport model is analysed, where convective flow of the plasma from the boundary layer to the first wall permits elevated particle densities in the boundary layer and leads to very high particle and energy transport. The convective flow is driven by the pressure gradient along the field lines which intersect the toroidal wall at an oblique small angle epsilon. The required thickness Δ of the boundary layer is around 10 15 n -1 .cm -2 . As a result, the plasma temperature there can be reduced towards the threshold of critical plasma-wall-interaction processes, the plasma core can be shielded against impurities from the wall and, at the same time, a very short life-time of all particles in the boundary layer can be achieved (use of pumpholes and/or scrape-off-limiters for removing ash). Thus, this model also improves the concepts of edge radiation cooling. An estimate is given of the parameters of INTOR using only a weak helical perturbation field which conserves the magnetic surfaces in the plasma core: one can reach wall temperatures Tsub(w) between 20 and 30 eV in the presence of wall densities nsub(w) approaching 10 14 cm -3 . (author)

Theropod courtship: large scale physical evidence of display arenas and avian-like scrape ceremony behaviour by Cretaceous dinosaurs

Science.gov (United States)

Lockley, Martin G.; McCrea, Richard T.; Buckley, Lisa G.; Deock Lim, Jong; Matthews, Neffra A.; Breithaupt, Brent H.; Houck, Karen J.; Gierliński, Gerard D.; Surmik, Dawid; Soo Kim, Kyung; Xing, Lida; Yong Kong, Dal; Cart, Ken; Martin, Jason; Hadden, Glade

2016-01-01

Relationships between non-avian theropod dinosaurs and extant and fossil birds are a major focus of current paleobiological research. Despite extensive phylogenetic and morphological support, behavioural evidence is mostly ambiguous and does not usually fossilize. Thus, inferences that dinosaurs, especially theropods displayed behaviour analogous to modern birds are intriguing but speculative. Here we present extensive and geographically widespread physical evidence of substrate scraping behavior by large theropods considered as compelling evidence of “display arenas” or leks, and consistent with “nest scrape display” behaviour among many extant ground-nesting birds. Large scrapes, up to 2 m in diameter, occur abundantly at several Cretaceous sites in Colorado. They constitute a previously unknown category of large dinosaurian trace fossil, inferred to fill gaps in our understanding of early phases in the breeding cycle of theropods. The trace makers were probably lekking species that were seasonally active at large display arena sites. Such scrapes indicate stereotypical avian behaviour hitherto unknown among Cretaceous theropods, and most likely associated with terrirorial activity in the breeding season. The scrapes most probably occur near nesting colonies, as yet unknown or no longer preserved in the immediate study areas. Thus, they provide clues to paleoenvironments where such nesting sites occurred.

Theropod courtship: large scale physical evidence of display arenas and avian-like scrape ceremony behaviour by Cretaceous dinosaurs.

Science.gov (United States)

Lockley, Martin G; McCrea, Richard T; Buckley, Lisa G; Lim, Jong Deock; Matthews, Neffra A; Breithaupt, Brent H; Houck, Karen J; Gierliński, Gerard D; Surmik, Dawid; Kim, Kyung Soo; Xing, Lida; Kong, Dal Yong; Cart, Ken; Martin, Jason; Hadden, Glade

2016-01-07

Relationships between non-avian theropod dinosaurs and extant and fossil birds are a major focus of current paleobiological research. Despite extensive phylogenetic and morphological support, behavioural evidence is mostly ambiguous and does not usually fossilize. Thus, inferences that dinosaurs, especially theropods displayed behaviour analogous to modern birds are intriguing but speculative. Here we present extensive and geographically widespread physical evidence of substrate scraping behavior by large theropods considered as compelling evidence of "display arenas" or leks, and consistent with "nest scrape display" behaviour among many extant ground-nesting birds. Large scrapes, up to 2 m in diameter, occur abundantly at several Cretaceous sites in Colorado. They constitute a previously unknown category of large dinosaurian trace fossil, inferred to fill gaps in our understanding of early phases in the breeding cycle of theropods. The trace makers were probably lekking species that were seasonally active at large display arena sites. Such scrapes indicate stereotypical avian behaviour hitherto unknown among Cretaceous theropods, and most likely associated with terrirorial activity in the breeding season. The scrapes most probably occur near nesting colonies, as yet unknown or no longer preserved in the immediate study areas. Thus, they provide clues to paleoenvironments where such nesting sites occurred.

Power deposition to the pump limiters in Tore-Supra with ohmic plasmas

International Nuclear Information System (INIS)

Guilhem, D.; Chatelier, M.; Chappuis Fleury, I.; Klepper, C.

1990-01-01

The modification of power scrape-off-length, λq, and power deposition are studied both with the horizontal limiter alone and with the full set of 7 pump limiters for 1MW ohmic plasmas in TORE-SUPRA. By making spatially resolved infrared surface temperature measurements during the plasma discharge, the magnitude and distribution of the energy flux can be derived. For comparison, the surface temperature of the horizontal pump limiter is calculated with a finite element code using a 3D description of the field lines, an exponential scrape-off-layer, and the pump limiter geometry. From comparison of the infrared images of the limiter we derived that the λq for power deposition was slightly less than 9 mm (±1mm) which is in agreement with the predicted design value of 10 mm. For an 8 seconds discharge, the maximum surface temperature on the horizontal limiter is 450 0 C. Inserting the 7 limiters does not modify λq (which becomes 10 mm). The power is shared by all the limiters and the maximum surface temperature on the horizontal limiter decreased to 320 0 C. These λq values have been independently measured by the integrated energy deposition on the horizontal limiter and other internal structures 5 cm into the scrape-off layer. These values agree with the infrared measurements in the two cases

Power deposition to the facing components in Tore-Supra

International Nuclear Information System (INIS)

Guilhem, D.; Chatelier, M.; Chappuis, P.; Koski, J.; Watkins, J.

1990-01-01

The modifications of the power scrape-off length, λ q and power deposition are studied for various configurations in ohmic Tore-Supra plasmas. The plasma is either touching the horizontal limiter alone, the full set of six pump limiters or the inner bumper limiter. All configurations are with and without the ergodic divertor system energized. From a comparison of the infrared images of the limiter we derived that the λ q for power deposition was slightly less than 9±1 mm in ohmic plasmas which is in agreement with the predicted design value of 10 mm. Using the six limiters, instead of one, does not modify λ q significantly, but leads to small asymmetries. The power is shared by all the limiters and the maximum surface temperature on the horizontal limiter decreases. These λ q values have been independently determined by calorimetric measurements on the integrated energy deposition on the horizontal limiter and other internal structures 5 cm into the scrape-off layer. These values agree with the infrared measurements in the two cases. In the presence of the ergodic divertor we observe a broadening of the scrape-off layer, the e-folding length for power deposition reaching 2.5 cm. Large asymmetries in the power deposition can be seen on the front face of the limiter, leading to the formation of hot spots at the leading edges. (orig.)

Interferometric density measurements in the divertor and edge plasma regions for the additionally heated JT-60 plasmas

International Nuclear Information System (INIS)

Fukuda, T.; Yoshida, H.; Nagashima, A.; Ishida, S.; Kikuchi, M.; Yokomizo, H.

1989-01-01

The first divertor plasma density measurement and the interferometric edge plasma density measurement with boundary condition preserving millimeter waveguides were demonstrated to elucidate the mutual correlation among the divertor plasma, scrape-off layer plasma and the bulk plasma properties in the additionally heated JT-60 plasmas. The electron density in the divertor region exhibited a nonlinear dependence on the bulk plasma density for the joule-heated plasmas. When neutral beam heating is applied on the plasmas with the electron density above 2x10 19 /m 3 , however, the bulk plasma density is scraped off from the outer region to lead to density clamping, and the electron density in the divertor region rapidly increases over 1x10 20 /m 3 , from which we can deduce that the particle flow along the magnetic field is dominant, resulting in the apparent degradation of the particle confinement time. As for the case when neutral beam injection is applied to low-density plasmas, the bulk plasma electron density profile becomes flattened to yield a smaller density increase in the divertor region and no density clamping of the bulk plasma was observed. Simulation analysis which correlates the transport of the divertor plasma and the scrape-off layer plasma was also carried out to find the consistency with the experimental results. (orig.)

Power deposition to the facing components in Tore-Supra

International Nuclear Information System (INIS)

Guilhem, D.; Chatelier, M.; Chappuis, P.

1990-01-01

The modification of power scrape-off-length, λq, and power deposition are studied during various configurations in ohmic TORE-SUPRA plasmas. The plasma is either leaning on the horizontal limiter alone, on the full set of 6 pump limiters or on the inner bumper limiter, all configurations with and without the ergodic divertor system energised. From comparison of the infrared images of the limiter we derived that the λq for power deposition was slightly less than 9 mm (±1 mm) in ohmic plasma which is in agreement with the predicted design value of 10 mm. Inserting the 6 limiters, instead of 1, does not modify significantly λq, but lead to small asymmetries. The power is shared by all the limiters and the maximum surface temperature on the horizontal limiter decreased. These λq values have been independently determined by calorimetric measurements done on the integrated energy deposition on the horizontal limiter and other internal structures 5 cm into the scrape-off layer. These values agree with the infrared measurements in the two cases. In the presence of the ergodic divertor we observe a broadening of the scrape off layer, the e-folding length for power deposition reaching 2.5 cm. Large asymmetries on power deposition can be seen on the front face of the limiter leading to the formation of hot spots at the leading edges

Plasma equilibrium profiles with applied resonant fields on TBR-1 tokamak

International Nuclear Information System (INIS)

Castro, R.M. de; Heller, M.V.A.P.; Caldas, I.L.; Silva, R.P. da; Brasilio, Z.A.; Oda, G.A.

1995-01-01

In this work we present the measurements of the plasma potential, in the edge and in the scrape-off layer regions of plasma, with and without the presence of the magnetic field perturbations produced by resonant helical windings. (author). 6 refs., 6 figs

The electron temperature gradient instability in presence of a limiter with tilted plates

International Nuclear Information System (INIS)

Farina, D.; Pozzoli, R.; Ryutov, D.

1994-01-01

The analysis of the electron temperature gradient instability in the scrape-off layer is generalized to the case of non-orthogonal intersections of the magnetic field with the wall surface, a situation which is most typical for a tokamak with a limiter. (orig.)

A constant heat flux plasma limiter for TEXTOR

International Nuclear Information System (INIS)

Mioduszewski, P.

1980-10-01

In future large tokamak machines heat removal from the plasma is going to play an important role. In TEXTOR the total plasma power is expected to be in the range of 0.5-2.5 MW. Typical fractions of about 50% of this power have to be removed from the plasma by limiters. The power flux from the limiter scrape-off layer to the limiter surface decays rapidly with distance into the scrape-off layer resulting in a highly space-dependent heat load on the limiter. Therefore, limiters are shaped in a way to smooth of the heat load, and the ideal limiter shape should produce a constant heat flux over the whole limiter surface. The ideally shaped limiter offers a better chance to handle the high heat loads with the preferred materials like stainless steel (or inconel 625 as in the case of TEXTOR). (orig./GG)

Thinning of Inner Retinal Layers after Vitrectomy with Silicone Oil versus Gas Endotamponade in Eyes with Macula-Off Retinal Detachment.

Science.gov (United States)

Purtskhvanidze, Konstantine; Hillenkamp, Jost; Tode, Jan; Junge, Olaf; Hedderich, Jürgen; Roider, Johann; Treumer, Felix

2017-01-01

To evaluate retinal layer thickness with optical coherence tomography (OCT) in eyes with macula-off retinal detachment after silicone oil (SiO) or gas endotamponade. Cross-sectional study of 40 eyes with macula-off rhegmatogenous retinal detachment that underwent vitrectomy. 20 eyes received SiO tamponade and 20 matched eyes received gas. 33 healthy fellow eyes served as controls. Macular spectral domain OCT was performed with automated layer detection in the 5 inner subfields of the Early Treatment Diabetic Retinopathy Study (ETDRS) map. Comparing the SiO group with the gas group, the ganglion cell layer showed a significant thinning in all fields of the inner ring of the ETDRS map, the inner plexiform layer in the nasal, superior and temporal quadrants, and the outer plexiform layer in the nasal quadrant. Inner retinal layers in the fovea/parafovea were significantly thinner in the SiO group. Prospective studies are warranted to further elucidate possible retinal adverse effects of SiO tamponade. © 2017 S. Karger AG, Basel.

Shear flow beneath oceanic plates: Local nonsimilarity boundary layers for olivine rheology

International Nuclear Information System (INIS)

Yuen, D.A.; Tovish, A.; Schubert, G.

1978-01-01

The principle of local similarity, which has been used to model the two-dimensional boundary layers in the oceanic upper mantle, permits calculation of the temperature, velocity, and stress fields with essentially analytic techniques. Finite difference numerical methods are hard pressed to resolve the detail required by the large variation of viscosity between the lithosphere and the asthenosphere. In this paper the local similarity approximation has been justified by quantitatively evaluating the effect of nonsimilarity due to viscous heating, nonlinear temperature- and pressure-dependent rheology, buoyancy, adiabatic cooling, etc. Nonsimilar effects produce only small modifications of the locally similar boundary layers; important geophysical observables such as surface heat flux and ocean floor topography are given to better than 10% by the locally similar solution. A posteriori evaluations of the term neglected in the boundary layer simplification of the complete equations have been conducted on the locally similar temperature and velocity profiles close to the spreading ridge. The boundary layer models are valid to depths of 100 km at 3 m.y. and 10 km at 0.3 m.y

Non-localized deformation in Cu−Zr multi-layer amorphous films under tension

Energy Technology Data Exchange (ETDEWEB)

Zhong, C. [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zhang, H. [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Department of Chemical and Materials Engineering, University of Alberta, Edmonton, Alberta T6G 1H9 (Canada); Cao, Q.P.; Wang, X.D. [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zhang, D.X. [State Key Laboratory of Modern Optical Instrumentation, Zhejiang University, Hangzhou 310027 (China); Hu, J.W. [Hangzhou Workers Amateur University, Hangzhou 310027 (China); Liaw, P.K. [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States); Jiang, J.Z., E-mail: jiangjz@zju.edu.cn [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China)

2016-09-05

In metallic glasses (MGs), plastic deformation at room temperature is dominated by highly localized shear bands. Here we report the non-localized deformation under tension in Cu−Zr multi-layer MGs with a pure amorphous structure using large-scale atomistic simulations. It is demonstrated that amorphous samples with high layer numbers, composed of Cu{sub 64}Zr{sub 36} and Cu{sub 40}Zr{sub 60}, or Cu{sub 64}Zr{sub 36} and Cu{sub 50}Zr{sub 50}, present obviously non-localized deformation behavior. We reveal that the deformation behavior of the multi-layer-structured MG films is related but not determined by the deformation behavior of the composed individual layers. The criterion for the deformation mode change for MGs with a pure amorphous structure, in generally, was suggested, i.e., the competition between the elastic-energy density stored and the energy density needed for forming one mature shear band in MGs. Our results provide a promising strategy for designing tensile ductile MGs with a pure amorphous structure at room temperature. - Highlights: • Tensile deformation behaviors in multi-layer MG films. • Films with high layer numbers confirmed with a non-localized deformation behavior. • The deformation mode is reasonably controlled by whether U{sub p} larger than U{sub SB.}.

Determining Off-Cycle Fuel Economy Benefits of 2-Layer HVAC Technology

Energy Technology Data Exchange (ETDEWEB)

Wood, Eric W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Moniot, Matthew [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jehlik, Forrest [Argonne National Laboratory; Chevers, Netsanet [Toyota Motor North America R& D; Hirabayshi, Hidekazu [Toyota Motor North America R& D; Song, Yuanpei [DENSO International America Inc.

2018-04-03

This work presents a methodology to determine the off-cycle fuel economy benefit of a 2-Layer HVAC system which reduces ventilation and heat rejection losses of the heater core versus a vehicle using a standard system. Experimental dynamometer tests using EPA drive cycles over a broad range of ambient temperatures were conducted on a highly instrumented 2016 Lexus RX350 (3.5L, 8 speed automatic). These tests were conducted to measure differences in engine efficiency caused by changes in engine warmup due to the 2-Layer HVAC technology in use versus the technology being disabled (disabled equals fresh air-considered as the standard technology baseline). These experimental datasets were used to develop simplified response surface and lumped capacitance vehicle thermal models predictive of vehicle efficiency as a function of thermal state. These vehicle models were integrated into a database of measured on road testing and coupled with U.S. typical meteorological data to simulate vehicle efficiency across seasonal thermal and operational conditions for hundreds of thousands of drive cycles. Fuel economy benefits utilizing the 2-Layer HVAC technology are presented in addition to goodness of fit statistics of the modeling approach relative to the experimental test data.

Large plasma pressure perturbations and radial convective transport in a tokamak

International Nuclear Information System (INIS)

Krasheninnikov, Sergei; Yu, Guanghui; Ryutov, Dmitri

2004-01-01

Strongly localized plasma structures with large pressure inhomogeneities (such as plasma blobs in the scrape-off-layer (SOL)/shadow regions, pellet clouds, Edge localized Modes (ELMs)) observed in the tokamaks, stellarators and linear plasma devices. Experimental studies of these phenomena reveal striking similarities including more convective rather than diffusive radial plasma transport. We suggest that rather simple models can describe many essentials of blobs, ELMs, and pellet clouds dynamics. The main ingredient of these models is the effective plasma gravity caused by magnetic curvature, centrifugal or friction forces effects. As a result, the equations governing plasma transport in such localized structures appear to be rather similar to that used to describe nonlinear evolution of thermal convection in the Boussinesq approximation (directly related to the Rayleigh-Taylor (RT) instability). (author)

Collisional transport across the magnetic field in drift-fluid models

DEFF Research Database (Denmark)

Madsen, Jens; Naulin, Volker; Nielsen, Anders Henry

2016-01-01

Drift ordered fluid models are widely applied in studies of low-frequency turbulence in the edge and scrape-off layer regions of magnetically confined plasmas. Here, we show how collisional transport across the magnetic field is self-consistently incorporated into drift-fluid models without...

Scrape-off layer radiation and heat load to the ASDEX Upgrade LYRA divertor

International Nuclear Information System (INIS)

Kallenbach, A.; Kaufmann, M.; Coster, D.P.

1999-01-01

In 1997 the new 'LYRA' divertor went into operation at ASDEX Upgrade and, in parallel, the neutral beam heating power was increased to 20 MW by installation of a second injector leading to a P/R value of 12 MW/m. Experiments have shown that the ASDEX Upgrade LYRA divertor is capable of handling such high heating powers. There is an overall reduction of the maximum heat flux in the LYRA divertor by about a factor of 2 compared with the previous open divertor Div I. This reduction is mainly due to increased radiative losses inside the divertor region, which are caused by an effective reflection of hydrogen neutrals into the hot separatrix region. The main channel of radiative loss is carbon radiation, which cools the divertor plasma down to a few electronvolts, where hydrogen radiation losses become significant. The radiative losses preferentially reduce the power flux at the separatrix, leading to early detachment around the strike point position. With increasing density, the detached region extends upwards on the vertical target. The power fraction radiated in the LYRA divertor is around 45% and nearly independent of the heating power. This value is a factor of 2 higher than the typical radiation fraction in Div I. B2-EIRENE modelling of the performed experiments supports the experimental finding and refines the understanding of loss processes in the divertor region. (author)

Poloidally asymmetric potential increases in tokamak scrape-off layer plasmas by radiofrequency power

International Nuclear Information System (INIS)

Diebold, D.A.; Majeski, R.; Tanaka, T.

1992-01-01

Langmuir probe data are presented which show poloidally asymmetric increases in floating potential, electron temperature and, hence, plasma potential on magnetic field lines which map to the Faraday shield of an ICRF antenna in a medium size tokamak, Phaedrus-T, during radiofrequency power injection. These data are consistent with and suggestive of the existence of radiofrequency generated sheath voltages on those field lines. (author). Letter-to-the-editor. 20 refs, 3 figs

Elastic–plastic adhesive impacts of tungsten dust with metal surfaces in plasma environments

NARCIS (Netherlands)

Ratynskaia, S.; Tolias, P.; Shalpegin, A.; Vignitchouk, L.; de Angeli, M.; I. Bykov,; Bystrov, K.; Bardin, S.; Brochard, F.; Ripamonti, D.; N. den Harder,; De Temmerman, G.

2015-01-01

Dust-surface collisions impose size selectivity on the ability of dust grains to migrate in scrape-off layer and divertor plasmas and to adhere to plasma-facing components. Here, we report first experimental evidence of dust impact phenomena in plasma environments concerning low-speed collisions of

Evolution of Excited Convective Cells in Plasmas

DEFF Research Database (Denmark)

Pécseli, Hans; Juul Rasmussen, Jens; Sugai, H.

1984-01-01

Convective cells are excited externally in a fully ionized magnetized plasma and their space-time evolution is investigated by two-dimensional potential measurements. A positive cell is excited externally by control of the end losses in the 'scrape off' layer of a plasma column produced by surface...

Local above-ground persistence of vascular plants : Life-history trade-offs and environmental constraints

NARCIS (Netherlands)

Ozinga, Wim A.; Hennekens, Stephan M.; Schaminee, Joop H. J.; Smits, Nina A. C.; Bekker, Renee M.; Roemermann, Christine; Klimes, Leos; Bakker, Jan P.; van Groenendael, Jan M.

Questions: 1. Which plant traits and habitat characteristics best explain local above-ground persistence of vascular plant species and 2. Is there a trade-off between local above-ground persistence and the ability for seed dispersal and below-ground persistence in the soil seed bank? Locations: 845

Time and space-resolved energy flux measurements in the divertor of the ASDEX tokamak by computerized infrared thermography

International Nuclear Information System (INIS)

Mueller, E.R.; Steinmetz, K.; Bein, B.K.

1984-06-01

A new, fully computerized and automatic thermographic system has been developed. Its two central components are an AGA THV 780 infrared camera and a PDP-11/34 computer. A combined analytical-numerical method of solving the 1-dimensional heat diffusion equation for a solid of finite thickness bounded by two parallel planes was developed. In high-density (anti nsub(e) = 8 x 10 13 cm -3 ) neutral-beam-heated (L-mode) divertor discharges in ASDEX, the power deposition on the neutralizer plates is reduced to about 10-15% of the total heating power, owing to the inelastic scattering of the divertor plasma from a neutral gas target. Between 30% and 40% of the power is missing in the global balance. The power flow inside the divertor chambers is restricted to an approximately 1-cm-thick plasma scrape-off layer. This width depends only weakly on the density and heating power. During H-phases free of Edge Localized Mode (ELM) activity the energy flow into the divertor is blocked. During H-phases with ELM activity the energy is expelled into the divertor in very short intense pulses (several MW for about one hundred μs). Sawtooth events are able to transport significant amounts of energy from the plasma core to the peripheral zones and the scrape-off layer, and they are frequently correlated with transitions from the L to the H mode. (orig./AH)

13th EU-US Transport Task Force Workshop on transport in fusion plasmas

DEFF Research Database (Denmark)

Connor, J.W.; Fasoli, A.; Hidalgo, C.

2009-01-01

This report summarizes the contributions presented at the 13th EU-US Transport Task Force Workshop on transport in fusion plasmas, held in Copenhagen, Denmark, 1-4 September 2008. There were sessions on core heat and particle transport; core and edge momentum transport; edge and scrape-off-layer ......This report summarizes the contributions presented at the 13th EU-US Transport Task Force Workshop on transport in fusion plasmas, held in Copenhagen, Denmark, 1-4 September 2008. There were sessions on core heat and particle transport; core and edge momentum transport; edge and scrape...

An Extension of the Miller Equilibrium Model into the X-Point Region

Science.gov (United States)

Hill, M. D.; King, R. W.; Stacey, W. M.

2017-10-01

The Miller equilibrium model has been extended to better model the flux surfaces in the outer region of the plasma and scrape-off layer, including the poloidally non-uniform flux surface expansion that occurs in the X-point region(s) of diverted tokamaks. Equations for elongation and triangularity are modified to include a poloidally varying component and grad-r, which is used in the calculation of the poloidal magnetic field, is rederived. Initial results suggest that strong quantitative agreement with experimental flux surface reconstructions and strong qualitative agreement with poloidal magnetic fields can be obtained using this model. Applications are discussed. A major new application is the automatic generation of the computation mesh in the plasma edge, scrape-off layer, plenum and divertor regions for use in the GTNEUT neutral particle transport code, enabling this powerful analysis code to be routinely run in experimental analyses. Work supported by US DOE under DE-FC02-04ER54698.

Carbon impurity transport around limiters in the DITE tokamak

International Nuclear Information System (INIS)

Pitcher, C.S.; Stangeby, P.C.; Goodall, D.H.J.; Matthews, G.F.; McCracken, G.M.

1989-01-01

The transport of impurity ions originating at the limiter in a tokamak is critically dependent on the location of the ion in the boundary plasma. In the confined plasma, just inboard of the limiter, impurity ions will disperse freely into the discharge whilst in the scrape-off layer the pre-sheath plasma flow and the associated ambipolar electric field may tend to sweep impurities back to the limiter surface. In this paper we have studied, both by experiment and by theory, the transport of carbon impurity ions in the vicinity of the limiter. By comparing experimental measurements of the spatial distributions of impurities around the limiter with that predicted from a Monte Carlo computer code it appears that the parallel dispersal on closed field lines in the confined plasma is consistent with classical transport processes and that in the scrape-off layer the dispersal is indeed impeded by the pre-sheath plasma flow. (orig.)

Heat loads on plasma facing components during disruptions on JET

International Nuclear Information System (INIS)

Arnoux, G.; Riccardo, V.; Fundamenski, W.; Loarte, A.; Huber, A.

2009-01-01

For the first time, fast measurements of heat loads on the main chamber plasma facing components (about 1 ms time resolution) during disruptions are taken on JET. The timescale of energy deposition during the thermal quench is estimated and compared with the timescale of the core plasma collapse measured with soft x-ray diagnostic. The energy deposition time is 3-8 times longer than the plasma energy collapse during density limit disruptions or radiative limit disruptions. This factor is rather in the range 1.5-4 for vertical displacement events. The heat load profiles measured during the thermal quench show substantial broadening of the power footprint on the upper dump plate. The scrape-off layer power width is increased by a factor of 3 for the density limit disruptions. The far scrape-off layer is characterized by a steeper gradient which could be explained by shadowing of the dump plate by other main chamber plasma facing components such as the outer limiter.

Plasma edge modelling with ICRF coupling

Directory of Open Access Journals (Sweden)

Zhang Wei

2017-01-01

Full Text Available The physics of Radio-Frequency (RF wave heating in the Ion Cyclotron Range of Frequencies (ICRF in the core plasmas of fusion devices are relatively well understood while those in the Scrape-Off Layer (SOL remain still unresolved. This paper is dedicated to study the ICRF interactions with the plasma edge, mainly from the theoretical and numerical point of view, in particular with the 3D edge plasma fluid and neutral transport code EMC3-EIRENE and various wave codes. Here emphasis is given to the improvement of ICRF coupling with local gas puffing and to the ICRF induced density convection in the SOL.

Integrated ELM simulation with edge MHD stability and transport of SOL-divertor plasmas

International Nuclear Information System (INIS)

Hayashi, Nobuhiko; Takizuka, Tomonori; Aiba, Nobuyuki; Ozeki, Takahisa; Oyama, Naoyuki

2007-07-01

The effect of the pressure profile on the energy loss caused by edge localized modes (ELMs) has been investigated by using an integrated simulation code TOPICS-IB based on a core transport code with a stability code for the peeling-ballooning modes and a transport model for scrape-off-layer and divertor plasmas. The steep pressure gradient inside the pedestal top is found to broaden the region of the ELM enhanced transport through the broadening of eigenfunctions and enhance the ELM energy loss. The ELM energy loss in the simulation becomes larger than 15% of the pedestal energy, as is shown in the database of multi-machine experiments. (author)

Layer-Mean Quantities, Local Conservation Laws, and Vorticity

International Nuclear Information System (INIS)

Camassa, R.; Levermore, C.D.

1997-01-01

We derive local conservation laws for layer-mean quantities in two general settings. When applied to Euler flows, the first of these settings yields well-known local conservation laws for quantities averaged between material surfaces. The second, however, leads to new local conservation laws for quantities involving the vorticity that are averaged between arbitrary surfaces. These produce the crucial vorticity conservation laws in shallow water models that admit nonhydrostatic and noncolumnar motion. Moreover, they seem to lie outside the Hamiltonian paradigm of fluid dynamics. The formalism generalizes to skew-symmetric matrix fields; applications to electromagnetism are suggested. copyright 1997 The American Physical Society

Off-critical local height probabilities on a plane and critical partition functions on a cylinder

Directory of Open Access Journals (Sweden)

Omar Foda

2018-03-01

Full Text Available We compute off-critical local height probabilities in regime-III restricted solid-on-solid models in a 4N-quadrant spiral geometry, with periodic boundary conditions in the angular direction, and fixed boundary conditions in the radial direction, as a function of N, the winding number of the spiral, and τ, the departure from criticality of the model, and observe that the result depends only on the product Nτ. In the limit N→1, τ→τ0, such that τ0 is finite, we recover the off-critical local height probability on a plane, τ0-away from criticality. In the limit N→∞, τ→0, such that Nτ=τ0 is finite, and following a conformal transformation, we obtain a critical partition function on a cylinder of aspect-ratio τ0. We conclude that the off-critical local height probability on a plane, τ0-away from criticality, is equal to a critical partition function on a cylinder of aspect-ratio τ0, in agreement with a result of Saleur and Bauer.

11. EU-US Transport Task Force Workshop - Proceedings

International Nuclear Information System (INIS)

2006-01-01

This document gives the program of the workshop and gathers only the slides of some of the papers presented. The presentations have been organized around 5 topics: 1) multi-scale physics, 2) momentum transport, 3) electron transport, 4) particle and impurity transport, and 5) plasma scrape-off layer transport

Filament structures at the plasma edge on MAST

International Nuclear Information System (INIS)

Kirk, A; Ayed, N Ben; Counsell, G; Dudson, B; Eich, T; Herrmann, A; Koch, B; Martin, R; Meakins, A; Saarelma, S; Scannell, R; Tallents, S; Walsh, M; Wilson, H R

2006-01-01

The boundary of the tokamak core plasma, or scrape-off layer, is normally characterized in terms of average parameters such as density, temperature and e-folding lengths suggesting diffusive losses. However, as is shown in this paper, localized filamentary structures play an important role in determining the radial efflux in both L mode and during edge localized modes (ELMs) on MAST. Understanding the size, poloidal and toroidal localization and the outward radial extent of these filaments is crucial in order to calculate their effect on power loading both on the first wall and the divertor target plates in future devices. The spatial and temporal evolution of filaments observed on MAST in L-mode and ELMs have been compared and contrasted in order to confront the predictions of various models that have been proposed to predict filament propagation and in particular ELM energy losses

Local layer structure of smectic liquid crystals by X-ray micro-diffraction

CERN Document Server

Takanishi, Y

2003-01-01

The local layer structure of smectic liquid crystal has been measured using time-resolved synchrotron X-ray micro-diffraction. Typical layer disorders observed in surface stabilized (anti-) ferroelectric liquid crystals, i.e. a stripe texture, a needed-like defect and a zigzag defect, are directly analyzed. The detailed analysis slows that the surface anchoring force due to the interaction between the liquid crystal molecule and the alignment thin film plays an important role to realize both the static and dynamic local layer structures. The layer structure of the circular domain observed in the liquid crystal of bent-shaped molecules found to depend on the applied electric field though the optical micrograph shows little difference. The frustrated, double and single layer structures of the bent-shaped molecule liquid crystal are determined depending on the terminal alkyl chain length. (author)

Overview of progress in European medium sized tokamaks towards an integrated plasma-edge/wall solution

NARCIS (Netherlands)

Meyer, H.; Eich, T.; Beurskens, M.N.A.; Coda, S.; Hakola, A.; Martin, P.; Adamek, J.; Agostini, M.; Aguiam, D.; Ahn, J.; Aho-Mantila, L.; Akers, R.; Albanese, R.; Aledda, R.; Alessi, E.; Allan, S.; Alves, D.; Ambrosino, R.; Amicucci, L.; Anand, H.; Anastassiou, G.; Andrèbe, Y.; Angioni, C.; Apruzzese, G.; Ariola, M.; Arnichand, H.; Arter, W.; Baciero, A.; Barnes, M.; Barrera, L.; Behn, R.; Bencze, A.; Bernardo, J.; Bernert, M.; Bettini, P.; Bilková, P.; Bin, W.; Birkenmeier, G.; Bizarro, J. P.S.; Blanchard, P.; Blanken, T.; Bluteau, M.; Bobkov, V.; Bogar, O.; Böhm, P.; Bolzonella, T.; Boncagni, L.; Botrugno, A.; Bottereau, C.; Bouquey, F.; Bourdelle, C.; Brémond, S.; Brezinsek, S.; Brida, D.; Brochard, F.; Buchanan, J.; Bufferand, H.; Buratti, P.; Cahyna, P.; Calabrò, G.; Camenen, Y.; Caniello, R.; Cannas, B.; Canton, A.; Cardinali, A.; Carnevale, D.; Carr, M.; Carralero, D.; Carvalho, P.; Casali, L.; Castaldo, C.; Castejón, F.; Castro, R.; Causa, F.; Cavazzana, R.; Cavedon, M.; Cecconello, M.; Ceccuzzi, S.; Cesario, R.; Challis, C.D.; Chapman, I.T.; Chapman, S.; Chernyshova, M.; Choi, D.; Cianfarani, C.; Ciraolo, G.; Citrin, J.; Clairet, F.; Classen, I.; Coelho, R.; Coenen, J. W.; Colas, L.; Conway, G.; Corre, Y.; Costea, S.; Crisanti, F.; Cruz, N.; Cseh, G.; Czarnecka, A.; D'Arcangelo, O.; De Angeli, M.; De Masi, G.; De Temmerman, G.; De Tommasi, G.; Decker, J.; Delogu, R. S.; Dendy, R.; Denner, P.; Di Troia, C.; Dimitrova, M.; D'Inca, R.; Dorić, V.; Douai, D.; Drenik, A.; Dudson, B.; Dunai, D.; Dunne, M.; Duval, B. P.; Easy, L.; Elmore, S.; Erdös, B.; Esposito, B.; Fable, E.; Faitsch, M.; Fanni, A.; Fedorczak, N.; Felici, F.; Ferreira, J.; Février, O.; Ficker, O.; Fietz, S.; Figini, L.; Figueiredo, A.; Fil, A.; Fishpool, G.; Fitzgerald, M.; Fontana, M.; Ford, O.; Frassinetti, L.; Fridström, R.; Frigione, D.; Fuchert, G.; Fuchs, C.; Furno Palumbo, M.; Futatani, S.; Gabellieri, L.; Gałazka, K.; Galdon-Quiroga, J.; Galeani, S.; Gallart, D.; Gallo, A.; Galperti, C.; Gao, Y.; Garavaglia, S.; Garcia, J.; Garcia-Carrasco, A.; Garcia-Lopez, J.; Garcia-Munoz, M.; Gardarein, J. L.; Garzotti, L.; Gaspar, J.; Gauthier, E.; Geelen, P.; Geiger, B.; Ghendrih, P.; Ghezzi, F.; Giacomelli, L.; Giannone, L.; Giovannozzi, E.; Giroud, C.; Gleason González, C.; Gobbin, M.; Goodman, T. P.; Gorini, G.; Gospodarczyk, M.; Granucci, G.; Gruber, M.; Gude, A.; Guimarais, L.; Guirlet, R.; Gunn, J.; Hacek, P.; Hacquin, S.; Hall, S.; Ham, C.; Happel, T.; Harrison, J.; Harting, D.; Hauer, V.; Havlickova, E.; Hellsten, T.; Helou, W.; Henderson, S.; Hennequin, P.; Heyn, M.; Hnat, B.; Hölzl, M.; Hogeweij, D.; Honoré, C.; Hopf, C.; Horáček, J.; Hornung, G.; Horváth, L.; Huang, Z.; Huber, A.; Igitkhanov, J.; Igochine, V.; Imrisek, M.; Innocente, P.; Ionita-Schrittwieser, C.; Isliker, H.; Ivanova-Stanik, I.; Jacobsen, A. S.; Jacquet, P.; Jakubowski, M.; Jardin, A.; Jaulmes, F.; Jenko, F.; Jensen, T.; Jeppe Miki Busk, O.; Jessen, M.; Joffrin, E.; Jones, O.; Jonsson, T.; Kallenbach, A.; Kallinikos, N.; Kálvin, S.; Kappatou, A.; Karhunen, J.; Karpushov, A.; Kasilov, S.; Kasprowicz, G.; Kendl, A.; Kernbichler, W.; Kim, D.; Kirk, A.; Kjer, S.; Klimek, I.; Kocsis, G.; Kogut, D.; Komm, M.; Korsholm, S. B.; Koslowski, H. R.; Koubiti, M.; Kovacic, J.; Kovarik, K.; Krawczyk, N.; Krbec, J.; Krieger, K.; Krivska, A.; Kube, R.; Kudlacek, O.; Kurki-Suonio, T.; Labit, B.; Laggner, F. M.; Laguardia, L.; Lahtinen, A.; Lalousis, P.; Lang, P.; Lauber, P.; Lazányi, N.; Lazaros, A.; Le, H.B.; Lebschy, A.; Leddy, J.; Lefévre, L.; Lehnen, M.; Leipold, F.; Lessig, A.; Leyland, M.; Li, L.; Liang, Y.; Lipschultz, B.; Liu, Y.Q.; Loarer, T.; Loarte, A.; Loewenhoff, T.; Lomanowski, B.; Loschiavo, V. P.; Lunt, T.; Lupelli, I.; Lux, H.; Lyssoivan, A.; Madsen, J.; Maget, P.; Maggi, C.; Maggiora, R.; Magnussen, M. L.; Mailloux, J.; Maljaars, B.; Malygin, A.; Mantica, P.; Mantsinen, M.; Maraschek, M.; Marchand, B.; Marconato, N.; Marini, C.; Marinucci, M.; Markovic, T.; Marocco, D.; Marrelli, L.; Martin, Y.; Martin Solis, J. R.; Martitsch, A.; Mastrostefano, S.; Mattei, M.; Matthews, G.; Mavridis, M.; Mayoral, M. L.; Mazon, D.; McCarthy, P.; McAdams, R.; McArdle, G.; McCarthy, P.; McClements, K.; McDermott, R.; McMillan, B.; Meisl, G.; Merle, A.; Meyer, O.; Milanesio, D.; Militello, F.; Miron, I. G.; Mitosinkova, K.; Mlynar, J.; Mlynek, A.; Molina, D.; Molina, P.; Monakhov, I.; Morales, J.; Moreau, D.; Morel, P.; Moret, J. M.; Moro, A.; Moulton, D.; Müller, H. W.; Nabais, F.; Nardon, E.; Naulin, V.; Nemes-Czopf, A.; Nespoli, F.; Neu, R.; Nielsen, A. H.; Nielsen, S. K.; Nikolaeva, V.; Nimb, S.; Nocente, M.; Nouailletas, R.; Nowak, S.; Oberkofler, M.; Oberparleiter, M.; Ochoukov, R.; Odstrčil, T.; Olsen, J.; Omotani, J.; O'Mullane, M. G.; Orain, F.; Osterman, N.; Paccagnella, R.; Pamela, S.; Pangione, L.; Panjan, M.; Papp, G.; Papřok, R.; Parail, V.; Parra, F. I.; Pau, A.; Pautasso, G.; Pehkonen, S. P.; Pereira, A.; Perelli Cippo, E.; Pericoli Ridolfini, V.; Peterka, M.; Petersson, P.; Petrzilka, V.; Piovesan, P.; Piron, C.; Pironti, A.; Pisano, F.; Pisokas, T.; Pitts, R.; Ploumistakis, I.; Plyusnin, V.; Pokol, G.; Poljak, D.; Pölöskei, P.; Popovic, Z.; Pór, G.; Porte, L.; Potzel, S.; Predebon, I.; Preynas, M.; Primc, G.; Pucella, G.; Puiatti, M. E.; Pütterich, T.; Rack, M.; Ramogida, G.; Rapson, C.; Rasmussen, J. Juul; Rasmussen, J.; Rattá, G. A.; Ratynskaia, S.; Ravera, G.; Réfy, D.; Reich, M.; Reimerdes, H.; Reimold, F.; Reinke, M.; Reiser, D.; Resnik, M.; Reux, C.; Ripamonti, D.; Rittich, D.; Riva, G.; Rodriguez-Ramos, M.; Rohde, V.; Rosato, J.; Ryter, F.; Saarelma, S.; Sabot, R.; Saint-Laurent, F.; Salewski, M.; Salmi, A.; Samaddar, D.; Sanchis-Sanchez, L.; Santos, J.; Sauter, O.; Scannell, R.; Scheffer, M.; Schneider, M.; Schneider, B.; Schneider, P.; Schneller, M.; Schrittwieser, R.; Schubert, M.; Schweinzer, J.; Seidl, J.; Sertoli, M.; Šesnić, S.; Shabbir, A.; Shalpegin, A.; Shanahan, B.; Sharapov, S.; Sheikh, U.; Sias, G.; Sieglin, B.; Silva, C.; Silva, A.; Silva Fuglister, M.; Simpson, J.; Snicker, A.; Sommariva, C.; Sozzi, C.; Spagnolo, S.; Spizzo, G.; Spolaore, M.; Stange, T.; Stejner Pedersen, M.; Stepanov, I.; Stober, J.; Strand, P.; Šušnjara, A.; Suttrop, W.; Szepesi, T.; Tál, B.; Tala, T.; Tamain, P.; Tardini, G.; Tardocchi, M.; Teplukhina, A.; Terranova, D.; Testa, D.; Theiler, C.; Thornton, A.; Tolias, P.; Tophj, L.; Treutterer, W.; Trevisan, G. L.; Tripsky, M.; Tsironis, C.; Tsui, C.; Tudisco, O.; Uccello, A.; Urban, J.; Valisa, M.; Vallejos, P.; Valovic, M.; Van Den Brand, H.; Vanovac, B.; Varoutis, S.; Vartanian, S.; Vega, J.; Verdoolaege, G.; Verhaegh, K.; Vermare, L.; Vianello, N.; Vicente, J.; Viezzer, E.; Vignitchouk, L.; Vijvers, W.A.J.; Villone, F.; Viola, B.; Vlahos, L.; Voitsekhovitch, I.; Vondráček, P.; Vu, N. M.T.; Wagner, D.; Walkden, N.; Wang, N.; Wauters, T.; Weiland, M.; Weinzettl, V.; Westerhof, E.; Wiesenberger, M.; Willensdorfer, M.; Wischmeier, M.; Wodniak, I.; Wolfrum, E.; Yadykin, D.; Zagórski, R.; Zammuto, I.; Zanca, P.; Zaplotnik, R.; Zestanakis, P.; Zhang, W.; Zoletnik, S.; Zuin, M.

2017-01-01

Integrating the plasma core performance with an edge and scrape-off layer (SOL) that leads to tolerable heat and particle loads on the wall is a major challenge. The new European medium size tokamak task force (EU-MST) coordinates research on ASDEX Upgrade (AUG), MAST and TCV. This multi-machine

Overview of progress in European medium sized tokamaks towards an integrated plasma-edge/wall solution

DEFF Research Database (Denmark)

Meyer, H.; Eich, T.; Beurskens, M.

2017-01-01

Integrating the plasma core performance with an edge and scrape-off layer (SOL) that leads to tolerable heat and particle loads on the wall is a major challenge. The new European medium size tokamak task force (EU-MST) coordinates research on ASDEX Upgrade (AUG), MAST and TCV. This multi-machine ...

Melt layer macroscopic erosion of tungsten and other metals under plasma heat loads simulating ITER off-normal events

International Nuclear Information System (INIS)

Garkusha, I.E.; Bandura, A.N.; Byrka, O.V.; Kulik, N.V.; Landman, I.; Wuerz, H.

2002-01-01

This paper is focused on experimental analysis of metal layer erosion and droplet splashing of tungsten and other metals under heat loads typical for ITER FEAT off-normal events,such as disruptions and VDE's. Plasma pressure gradient action on melt layer results in erosion crater formation with mountains of displaced material at the crater edge. It is shown that macroscopic motion of melt layer and surface cracking are the main factors responsible for tungsten damage. Weight loss measurements of all exposed materials demonstrate inessential contribution of evaporation process to metals erosion

Dimensional crossover of electron weak localization in ZnO/TiO{sub x} stacked layers grown by atomic layer deposition

Energy Technology Data Exchange (ETDEWEB)

Saha, D., E-mail: sahaphys@gmail.com, E-mail: pmisra@rrcat.gov.in; Misra, P., E-mail: sahaphys@gmail.com, E-mail: pmisra@rrcat.gov.in; Joshi, M. P.; Kukreja, L. M. [Laser Materials Processing Division, Raja Ramanna Centre for Advanced Technology, Indore 452 013 (India); Bhartiya, S. [Laser Materials Development & Devices Division, Raja Ramanna Centre for Advanced Technology, Indore 452 013 (India); Gupta, M. [UGC-DAE Consortium for Scientific Research, Indore 452 017 (India)

2016-01-25

We report on the dimensional crossover of electron weak localization in ZnO/TiO{sub x} stacked layers having well-defined and spatially-localized Ti dopant profiles along film thickness. These films were grown by in situ incorporation of sub-monolayer TiO{sub x} on the growing ZnO film surface and subsequent overgrowth of thin conducting ZnO spacer layer using atomic layer deposition. Film thickness was varied in the range of ∼6–65 nm by vertically stacking different numbers (n = 1–7) of ZnO/TiO{sub x} layers of nearly identical dopant-profiles. The evolution of zero-field sheet resistance (R{sub ◻}) versus temperature with decreasing film thickness showed a metal to insulator transition. On the metallic side of the metal-insulator transition, R{sub ◻}(T) and magnetoresistance data were found to be well corroborated with the theoretical framework of electron weak localization in the diffusive transport regime. The temperature dependence of both R{sub ◻} and inelastic scattering length provided strong evidence for a smooth crossover from 2D to 3D weak localization behaviour. Results of this study provide deeper insight into the electron transport in low-dimensional n-type ZnO/TiO{sub x} stacked layers which have potential applications in the field of transparent oxide electronics.

Simulation of the ASDEX divertor performance after hardening

International Nuclear Information System (INIS)

Schneider, W.; Lackner, K.; Neuhauser, J.; Wunderlich, R.

1985-05-01

Two combined computer models - a fluid description of the plasma scrape-off layer (SOLID) and a Monte-Carlo code for the neutral gas dynamics (DEGAS) - are used to assess changes in the divertor performance expected from the modifications in geometry needed for hardening the ASDEX divertor chamber for long-pulse, high-power heating. Stand-alone DEGAS calculations with assumed fixed scrape-off plasma parameters predict a doubling of the neutral escape probability, which, however, still remains so low, that achievement of the high divertor recycling regime can be expected over roughly the same operational regime as before modifications. This conclusion is also supported by fully self-consistent calculations with the combined model. Due to the reduced divertor, a significant reduction is predicted in the divertor time constant, which is expected to affect transient phenomena. (orig.)

Wetting-layer formation mechanisms of surface-directed phase separation under different quench depths with off-critical compositions in polymer binary mixture

Science.gov (United States)

Yan, Li-Tang; Xie, Xu-Ming

2007-02-01

Focusing on the off-critical condition, the quench depth dependence of surface-directed phase separation in the polymer binary mixture is numerically investigated by combination of the Cahn-Hilliard-Cook theory and the Flory-Huggins-de Gennes theory. Two distinct situations, i.e., for the wetting, the minority component is preferred by the surface and the majority component is preferred by the surface, are discussed in detail. The simulated results show that the formation mechanism of the wetting layer is affected by both the quench depth and the off-critical extent. Moreover, a diagram, illustrating the formation mechanisms of the wetting layer with various quench depths and compositions, is obtained on the basis of the simulated results. It is found that, when the minority component is preferred by the surface, the growth of the wetting layer can exhibit pure diffusion limited growth law, logarithmic growth law, and Lifshitz-Slyozov growth law. However, when the majority component is preferred by the surface, the wetting layer always grows logarithmically, regardless of the quench depth and the off-critical extent. It is interesting that the surface-induced nucleation can be observed in this case. The simulated results demonstrate that the surface-induced nucleation only occurs below a certain value of the quench depth, and a detailed range about it is calculated and indicated. Furthermore, the formation mechanisms of the wetting layer are theoretically analyzed in depth by the chemical potential gradient.

Divertor experiment for impurity control in DIVA

International Nuclear Information System (INIS)

Nagami, Masayuki

1979-04-01

Divertor actions of controlling the impurities and the transport of impurity ions in the plasma have been investigated in the DIVA device. Following are the results: (1) The radial transport of impurity ions is not described only by neoclassical theory, but it is strongly influenced by anomalous process. Radial diffusion of impurity ions across the whole minor radius is well described by a neoclassical diffusion superposed by the anomalous diffusion for protons. Due to this anomalous process, which spreads the radial density profile of impurity ions, 80 to 90% of the impurity flux in the plasma outer edge is shielded even in a nondiverted discharge. (2) The divertor reduces the impurity flux entering the main plasma by a factor of 2 to 4. The impurity ions shielded by the scrape-off plasma are rapidly guided into the burial chamber with a poloidal excursion time roughly equal to that of the scrape-off plasma. (3) The divertor reduces the impurity ion flux onto the main vacuum chamber by guiding the impurity ions diffusing from the main plasma into the burial chamber, thereby reducing the plasma-wall interaction caused by diffusing impurity ions at the main vacuum chamber. The impurity ions produced in the burial chamber may flow back to the main plasma through the scrape-off layer. However, roughly only 0.3% of the impurity flux into the scrape-off plasma in the burial chamber penetrates into the main plasma due to the impurity backflow. (4) A slight cooling of the scrape-off plasma with light-impurity injection effectively reduces the metal impurity production at the first wall by reducing the potential difference between the plasma and the wall, thereby reducing the accumulation of the metal impurity in the discharge. Radiation cooling by low-Z impurities in the plasma outer edge, which may become an important feature in future large tokamaks both with and without divertor, is numerically evaluated for carbon, oxygen and neon. (author)

Enhancement of Faraday effect in one-dimensional magneto-optical photonic crystal including a magnetic layer with wavelength dependent off-diagonal elements of dielectric constant tensor

International Nuclear Information System (INIS)

Inui, Chie; Ozaki, Shinsuke; Kura, Hiroaki; Sato, Tetsuya

2011-01-01

Optical and magneto-optical properties of one-dimensional magneto-optical photonic crystal (1-D MPC) prepared by the sol-gel dip-coating method, including a magnetic defect layer composed of mixture of CoFe 2 O 4 and SiO 2 , are investigated from both the experimental and theoretical standpoints. The resonant transmission of light was observed around 570 nm in the photonic band gap. The Faraday rotation angle θ F showed two maxima at 490 and 640 nm, and the wavelength dependence of θ F above 760 nm was similar to that of the CoFe 2 O 4 +SiO 2 single-layer film. The two maxima of θ F are attributed to the enhanced Faraday rotation of nonmagnetic TiO 2 layers in the cavity structure and that in magnetic CoFe 2 O 4 +SiO 2 layer through the light localization in MPC. The maximum value of θ F due to the magnetic CoFe 2 O 4 +SiO 2 layer in the MPC was 22-times larger than that in the single-layer film. The simulation study of MPC with CoFe 2 O 4 +SiO 2 magnetic defect layer, based on the matrix approach method, showed that the resonant light transmission was accompanied by the localization of electric field, and large enhancement of θ F appeared at different wavelengths so as to agree with the experimental features. This can be explained in terms of the wavelength dependent off-diagonal components of the dielectric constant tensor in addition to the large extinction coefficient in the CoFe 2 O 4 +SiO 2 magnetic defect layer. - Highlights: → 1-D magnetic photonic crystal (MPC) prepared by sol-gel method. → Enhancement of Faraday rotation due to the magnetic defect layer of CoFe 2 O 4 . → Shift of wavelength of Faraday rotation maximum from resonant light transmission.

Characteristics of fuel CRUD from Ringhals Unit 4. A comparison of CRUD samples from ultrasonic fuel cleaning and fuel scrape

International Nuclear Information System (INIS)

Chen, Jiaxin; Eskhult, Jonas; Marks, Chuck; Dingee, John; Bengtsson, Bernt; Wells, Daniel

2014-01-01

The characteristics and behaviour of PWR fuel CRUD are closely related to plant radiation field build-up and the risks of CRUD-Induced Power Shifts (CIPS, previously AOA) and CRUD-Induced Localized Corrosion (CILC). At Ringhals NPP fuel scrape technology has frequently been used to collect fuel CRUD samples as a part of plant water chemistry monitoring programs. In 2012, high efficiency ultrasonic fuel cleaning (HE-UFC) technology was first used at Ringhals Unit 4 to reduce the risk of CIPS, which was expected to increase due to steam generator replacement and a subsequent power uprate. In the HE-UFC system a “first-of-a-kind” CRUD sampling system was installed for collecting fuel CRUD. It is of interest to compare the fuel CRUD samples collected by the two different CRUD sampling methods and to understand if HE-UFC crud sampling could be used to replace or supplement the fuel scrape method. This paper presents some preliminary results on isotopic compositions, elemental compositions, and phase compositions of fuel CRUD samples collected from similar fuel rods and assemblies by both methods during the 2012 refueling outage, one cycle after steam generator replacement at Ringhals Unit 4. The results show that the characteristics of fuel CRUD sampled by HE-UFC and fuel scrape, although not always identical, were similar or correlated to some extent in terms of weight ratios of Ni to Fe and Cr to Fe as well as specific activities of Co-58, Co-60 and Cr-51. However, due to the limited experience with the HE-UFC sampling method, more consideration is required if the statistical significance of the obtained data and indications are to be verified. (author)

The Impacts of Off-Campus Students on Local Neighbourhood in Malaysia

OpenAIRE

Dasimah Bt Omar; Faizul Abdullah; Fatimah Yusof; Hazlina Hamdan; Naasah Nasrudin; Ishak Che Abullah

2011-01-01

The impacts of near-campus student housing, or offcampus students accommodation cannot be ignored by the universities and as well as the community officials. Numerous scholarly studies, have highlighted the substantial economic impacts either; direct, indirect or induced, and cumulatively the roles of the universities have significantly contributed to the local economies. The issue of the impacts of off-campus student rental housing on neighbourhoods is one that has been ...

Palm trees and islands - Current filaments in the edge of JET

Energy Technology Data Exchange (ETDEWEB)

Maszl, Ch., E-mail: christian.maszl@uibk.ac.at [JET-EFDA, Culham Science Centre, OX14 3DB, Abingdon (United Kingdom); Association EURATOM/OAW, Institute for Ion Physics and Applied Physics, University of Innsbruck (Austria); Naulin, V. [JET-EFDA, Culham Science Centre, OX14 3DB, Abingdon (United Kingdom); Association EURATOM/RISO DTU, Danish Technical University, Roskilde (Denmark); Brix, M. [JET-EFDA, Culham Science Centre, OX14 3DB, Abingdon (United Kingdom); Association EURATOM/CCFE, Culham Science Centre, Abingdon (United Kingdom); Versloot, T.W. [JET-EFDA, Culham Science Centre, OX14 3DB, Abingdon (United Kingdom); Association EURATOM/FOM, FOM Institute Rijnhuizen, Nieuwegein (Netherlands); Schrittwieser, R. [JET-EFDA, Culham Science Centre, OX14 3DB, Abingdon (United Kingdom); Association EURATOM/OAW, Institute for Ion Physics and Applied Physics, University of Innsbruck (Austria)

2011-08-01

It is now well known that edge localized modes (ELMs) lead to the ejection of a number of filamentary structures into the scrape-off layer (SOL). ELMs thus generate structures with excess energy and density. Recent results show that ELM filaments also carry current. Furthermore it can be conjectured that ELM filaments leave corresponding holes behind. If such a hole is able to reach a resonant magnetic surface it may close on itself and thus increase its lifetime significantly, thereby becoming detectable. We presume that the Palm Tree Mode (PTM) is a signature of such an event. Understanding PTMs therefore enhances our knowledge of ELMs and edge physics and contributes to the verification of ELM models.

The physics of transport barrier formation in the PBX-M H-mode

International Nuclear Information System (INIS)

Tynan, G.R.; Schmitz, L.; Blush, L.

1994-01-01

Measurements of edge profiles, turbulence, and turbulent-driven transport were made inside the last-closed flux surface (LCFS) and in the scrape-off layer (SOL) of PBX-M L-mode and H-mode plasmas using a fast reciprocating Langmuir probe diagnostic. Direct measurements of the potential profile confirm the generation of a strong inward radial electric field (E r ∼ -100 V/cm) just inside the LCFS in H-mode. Density and potential fluctuations levels are reduced at the L-H transition, resulting in significantly lower turbulent transport. The reduction in turbulent transport occurs across the LCFS and SOL regions and is not localized to the region of strong radial electric field. (author)

Interplay between edge and outer core fluctuations in the tokamak Tore Supra

International Nuclear Information System (INIS)

Fenzi, C.; Garbet, X.; Capes, H.; Devynck, P.; Laviron, C.; Truc, A.; Gervais, F.; Hennequin, P.; Quemeneur, A.

2000-01-01

In the tokamak Tore Supra, when a poloidally and toroidally localized limiter, called a modular limiter, is introduced into the lower part of the scrape-off layer, density fluctuations located in the vicinity of this limiter present a specific feature with the appearance of a new spectral pattern in the associated frequency spectrum. This leads to a strong up-down asymmetry observed in both the plasma edge and the plasma outer core, with a maximum level of turbulence at the bottom of the plasma. The observed asymmetry characteristics show that magnetic connection lengths play a critical role here and that the limiter configuration has some effect on the outer core turbulence. (author)

Localization in superlattices with randomness in layer thickness

International Nuclear Information System (INIS)

Yuan Jian; Tsai Chienhua.

1987-08-01

The localization length for electrons in superlattices with randomness in layer thickness is studied in both the commensurate and the incommensurate cases. It is demonstrated that disorder limits the electrons to see only structures within the extent of their wave functions and to be hardly effected by any long range correlation. (author). 4 refs, 6 figs

Cassava root scrapings for 22 to 42-day-old broilers in high-temperature environments

Directory of Open Access Journals (Sweden)

Antônio Hosmylton Carvalho Ferreira

2012-06-01

Full Text Available The objective of this study was to analyze the effect of whole cassava root scrapings at different levels in diets for broilers in the period of 22 to 42 days of age in high-temperature environments on performance, as well as to evaluate the metabolizability of dry matter (DM, crude protein (CP and gross energy (GE and nitrogen balance. A total of 400 male Ross broilers were used for evaluation of performance and 80 birds of the same strain were used in the metabolism experiment. The design was of randomized block with five treatments and four replications. The experimental unit was represented by twenty birds on the performance evaluation and four birds were housed in metabolic cages for the metabolism evaluation. The treatments consisted of diets containing inclusion levels of cassava root scrapings (0, 50, 100, 150 and 200 g/kg, formulated to meet the nutritional requirements accordingly to each phase of the birds. Whole cassava root scrapings can be included in diets for 22 to 42 day-old broiler chickens, at a level between 118.75 and 200 k/kg, in environments of high temperatures, with positive interference on weight gain and feed conversion, without affecting the coefficient of metabolizability of dry matter, crude protein, gross energy and nitrogen balance, or carcass characteristics, such as yields of main cuts and metabolically active organs of the birds.

Neandertal humeri may reflect adaptation to scraping tasks, but not spear thrusting.

Directory of Open Access Journals (Sweden)

Colin N Shaw

Full Text Available Unique compared with recent and prehistoric Homo sapiens, Neandertal humeri are characterised by a pronounced right-dominant bilateral strength asymmetry and an anteroposteriorly strengthened diaphyseal shape. Remodeling in response to asymmetric forces imposed during regular underhanded spear thrusting is the most influential explanatory hypothesis. The core tenet of the "Spear Thrusting Hypothesis", that underhand thrusting requires greater muscle activity on the right side of the body compared to the left, remains untested. It is unclear whether alternative subsistence behaviours, such as hide processing, might better explain this morphology. To test this, electromyography was used to measure muscle activity at the primary movers of the humerus (pectoralis major (PM, anterior (AD and posterior deltoid (PD during three distinct spear-thrusting tasks and four separate scraping tasks. Contrary to predictions, maximum muscle activity (MAX and total muscle activity (TOT were significantly higher (all values, p<.05 at the left (non-dominant AD, PD and PM compared to the right side of the body during spear thrusting tasks. Thus, the muscle activity required during underhanded spearing tasks does not lend itself to explaining the pronounced right dominant strength asymmetry found in Neandertal humeri. In contrast, during the performance of all three unimanual scraping tasks, right side MAX and TOT were significantly greater at the AD (all values, p<.01 and PM (all values, p<.02 compared to the left. The consistency of the results provides evidence that scraping activities, such as hide preparation, may be a key behaviour in determining the unusual pattern of Neandertal arm morphology. Overall, these results yield important insight into the Neandertal behavioural repertoire that aided survival throughout Pleistocene Eurasia.

Quantitative Differentiation of LV Myocardium with and without Layer-Specific Fibrosis Using MRI in Hypertrophic Cardiomyopathy and Layer-Specific Strain TTE Analysis.

Science.gov (United States)

Funabashi, Nobusada; Takaoka, Hiroyuki; Ozawa, Koya; Kamata, Tomoko; Uehara, Masae; Komuro, Issei; Kobayashi, Yoshio

2018-05-30

To achieve further risk stratification in hypertrophic cardiomyopathy (HCM) patients, we localized and quantified layer-specific LVM fibrosis on MRI in HCM patients using regional layer-specific peak longitudinal strain (PLS) and peak circumferential strain (PCS) in LV myocardium (LVM) on speckle tracking transthoracic echocardiography (TTE). A total of 18 HCM patients (14 males; 58 ± 17 years) underwent 1.5T-MRI and TTE. PLS and PCS in each layer of the LVM (endocardium, epicardium, and whole-layer myocardium) were calculated for 17 AHA-defined lesions. MRI assessment showed that fibrosis was classified as endocardial, epicardial, or whole-layer (= either or both of these). Regional PLS was smaller in fibrotic endocardial lesions than in non-fibrotic endocardial lesions (P = 0.004). To detect LV endocardial lesions with fibrosis, ROC curves of regional PLS revealed an area under the curve (AUC) of 0.609 and a best cut-off point of 13.5%, with sensitivity of 65.3% and specificity of 54.3%. Regional PLS was also smaller in fibrotic epicardial lesions than in non-fibrotic epicardial lesions (P layer myocardium analysis, PLS was smaller in fibrotic lesions than in non-fibrotic lesions (P layer LV lesions with fibrosis, ROC curves of regional PLS revealed an AUC of 0.674 and a best cut-off point of 12.5%, with sensitivity of 79.0% and specificity of 50.7%. There were no significant differences in PCS of LV myocardium (endocardium, epicardium, and whole-layer) between fibrotic and non-fibrotic lesions. Quantitative regional PLS but not PCS in LV endocardium, epicardium, and whole-layer myocardium provides useful non-invasive information for layer-specific localization of fibrosis in HCM patients.

Observations with a mid-plane reciprocating probe in MAST

International Nuclear Information System (INIS)

Yang, Y.; Counsell, G.F.

2003-01-01

A fast reciprocating probe has recently been installed on MAST. It has been used to measure the outboard, mid-plane scrape off layer (SOL) of L-mode plasmas, and to study the intermittent fluctuations in the SOL in L-mode and ELMy H-mode discharges. In this paper, the system and the experiments are introduced

Core-edge coupling and the effect of the edge on overall plasma performance

International Nuclear Information System (INIS)

Fichtmueller, M.; Corrigan, G.; Lauro-Taroni, L.

1999-01-01

Several attempts to model the entire plasma cross section have been reported in the last few years. Two possibilities are to either couple a core code to a scrape-off layer (SOL) code at a specified interface or to extend the computational region of an SOL-code all the way to the plasma centre. The most advanced global code is the code COCONUT which is based on the former principle and comprises the Monte-Carlo code NIMBUS, the 2D scrape-off layer code EDGE2D, the core transport code JETTO and the core impurity transport code SANCO. A main feature of COCONUT is its modular structure which ensures a high degree of flexibility and the capability to cover a large range of time-scales. The influence of the SOL on the core is illustrated with a range of global simulations carried out with COCONUT. The simulations show that the primary effect of the SOL is the control of the particle sources and sinks with a secondary effect on plasma dilution, radiation and perhaps pedestal temperatures. (author)

Local-circuit phenotypes of layer 5 neurons in motor-frontal cortex of YFP-H mice

Directory of Open Access Journals (Sweden)

Jianing Yu

2008-12-01

Full Text Available Layer 5 pyramidal neurons comprise an important but heterogeneous group of cortical projection neurons. In motor-frontal cortex, these neurons are centrally involved in the cortical control of movement. Recent studies indicate that local excitatory networks in mouse motor-frontal cortex are dominated by descending pathways from layer 2/3 to 5. However, those pathways were identified in experiments involving unlabeled neurons in wild type mice. Here, to explore the possibility of class-specific connectivity in this descending pathway, we mapped the local sources of excitatory synaptic input to a genetically labeled population of cortical neurons: YFP-positive layer 5 neurons of YFP-H mice. We found, first, that in motor cortex, YFP-positive neurons were distributed in a double blade, consistent with the idea of layer 5B having greater thickness in frontal neocortex. Second, whereas unlabeled neurons in upper layer 5 received their strongest inputs from layer 2, YFP-positive neurons in the upper blade received prominent layer 3 inputs. Third, YFP-positive neurons exhibited distinct electrophysiological properties, including low spike frequency adaptation, as reported previously. Our results with this genetically labeled neuronal population indicate the presence of distinct local-circuit phenotypes among layer 5 pyramidal neurons in mouse motor-frontal cortex, and present a paradigm for investigating local circuit organization in other genetically labeled populations of cortical neurons.

Scraping the Monumental: Stepan Bandera through the Lens of Quantitative Memory Studies

NARCIS (Netherlands)

Fredheim, R.; Howanitz, G.; Makhortykh, M.

2014-01-01

In this essay we use the example of Stepan Bandera to demonstrate the effectiveness of web-scraping methods as a tool to explore how people interact with memory content online. Using data from Wikipedia, Twitter and YouTube, we analyse the traces left by users interested in Stepan Bandera and assess

Steady-state and time-dependent modelling of parallel transport in the scrape-off layer

Czech Academy of Sciences Publication Activity Database

Havlíčková, E.; Fundameski, W.; Naulin, V.; Nielsen, A.H.; Zagórski, R.; Seidl, Jakub; Horáček, Jan

2011-01-01

Roč. 53, č. 6 (2011), 065004-065004 ISSN 0741-3335 R&D Projects: GA ČR GAP205/10/2055; GA MŠk 7G09042 Institutional research plan: CEZ:AV0Z20430508 Keywords : Parallel transport * , SOLF1D Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.425, year: 2011 http://iopscience.iop.org/0741-3335/53/6/065004/pdf/0741-3335_53_6_065004.pdf

Investigation of scrape-off layer up-down asymmetries in diverted plasmas in TEXT-Upgrade

International Nuclear Information System (INIS)

Bonnin, X.P.G.

1998-05-01

On diverted discharges in TEXT-U, whether it be in single-null or double-null configurations, up-down asymmetries have been noted, the sign and magnitude of which depend on plasma conditions. Geometrical effects play a role in double-null discharges but may not explain the observations. Moreover, they do not play a role in the single-null plasmas, which are topologically up-down symmetric, so the asymmetry must come from physical driving mechanisms. To fully understand these drives a realistic edge plasma must be simulated. In so doing, the authors hope to gain insight as to which physical processes intervene in creating such asymmetries. The B2-Eirene plasma simulation code, upgraded and partially rewritten to handle the various geometries, will be a useful tool in evaluating the respective influences of the driving terms. Several such mechanisms will be investigated, both computationally and experimentally, and compared with data from previous tokamak discharges. In the course of this, theoretical predictions for edge transport phenomena, for example, atomic drives, curvature drives and neoclassical drifts, possibly leading to asymmetries, will be compared to experiment

Comparing scrape-off layer and divertor physics in JET pure He and D discharges

NARCIS (Netherlands)

Pitts, R.A.; Andrew, P.; Andrew, Y.; Becoulet, M.; Coffey, I.; Coster, D.; McDonald, D. C.; Eich, T.; Erents, S.K.; Fenstermacher, M.E.; Fundamenski, W.; Haas, G.; Hermann, A.; Hidalgo, C.; Hillis, D.; Huber, A.; Ingesson, L. C.; Jachmich, S.; Kallenbach, A.; Korotkov, A.; Lawson, K.; Lomas, P.; Loarer, T.; Loarte, A.; Matthews, G. F.; McCracken, G.; Meigs, A.; Mertens, P.; O' Mullane, M.; Phillipps, V.; Porter, G.; Pospieszczyk, A.; Rapp, J.; Reiter, D.; Riccardo, V.; Saibene, G.; Sartori, R.; Stamp, M. F.; Tsitrone, E.; Wischmeier, W.; Gafert, J.

2003-01-01

Though helium plasmas are one option for the low activation phase of ITER, little effort has thus far been devoted to studying them in a large, diverted tokamak. A recent campaign on JET has therefore sought to address some of the important questions related to helium operation (He concentrations

Local environmental conditions and the stability of protective layers on steel surfaces

Energy Technology Data Exchange (ETDEWEB)

Jensen, J P [Technical Univ. of Denmark, Lyngby (Denmark); Bursik, A

1996-12-01

Local environmental conditions determine whether the protective layers on steel surfaces are stable. With unfavorable local environmental conditions, the protective layers may be subject to damage. Taking the cation conductivity of all plant cycle streams <0.2 {mu}S/cm for granted, an adequate feed-water and - if applicable - boiler water conditioning is required to prevent such damage. Even if the mentioned conditions are met in a bulk, the local environmental conditions may be inadequate. The reasons for this may be the disregarding of interactions among material, design, and chemistry. The paper presents many possible mechanisms of protective layer damage that are directly influenced or exacerbated by plant cycle chemistry. Two items are discussed in more detail: First, the application of all volatile treatment for boiler water conditioning of drum boiler systems operating at low pressures and, second, the chemistry in the transition zone water/steam in the low pressure turbine. The latter is of major interest for the understanding and prevention of corrosion due to high concentration of impurities in the aqueous liquid phases. This is a typical example showing that local environmental conditions may fundamentally differ from the overall bulk chemistry. (au) 19 refs.

DIII-D Edge Plasma, Disruptions, and Radiative Processes. Final Report

Energy Technology Data Exchange (ETDEWEB)

Boedo, J. A.; Luckhardt, S.C.; Moyer, R. A.

2001-01-01

The scientific goal of the UCSD-DIII-D Collaboration during this period was to understand the coupling of the core plasma to the plasma-facing components through the plasma boundary (edge and scrape-off layer). To achieve this goal, UCSD scientists studied the transport of particles, momentum, energy, and radiation from the plasma core to the plasma-facing components under normal (e.g., L-mode, H-mode, and ELMs), and off-normal (e.g., disruptions) operating conditions.

DIII-D Edge Plasma, Disruptions, and Radiative Processes. Final Report

International Nuclear Information System (INIS)

Boedo, J. A.; Luckhardt, S.C.; Moyer, R. A.

2001-01-01

The scientific goal of the UCSD-DIII-D Collaboration during this period was to understand the coupling of the core plasma to the plasma-facing components through the plasma boundary (edge and scrape-off layer). To achieve this goal, UCSD scientists studied the transport of particles, momentum, energy, and radiation from the plasma core to the plasma-facing components under normal (e.g., L-mode, H-mode, and ELMs), and off-normal (e.g., disruptions) operating conditions

Radio Frequency Enhanced Plasma Potential and Flows in the Scrap-Off Layer of an Active Antenna

Science.gov (United States)

Martin, Michael John

Ion cyclotron resonance heating (ICRH) systems are critical components of current and future tokamak experiments aimed at producing nuclear fusion energy. During ICRH a host of deleterious effects occur, including increased heat flux to plasma facing components and modification of launched wave power. A suspected root cause of these effects is the radio frequency (RF) rectification of the plasma potential. Interest in the antenna scrape-off layer (SOL) region has drawn increasing interest, as it is recognized that mitigating these effects is necessary to achieving fusion power. This dissertation investigates the RF rectification of the plasma potential and the resulting cross-field flows that form due to an active RF antenna. The experiment is performed in the Large Plasma Device (LAPD) utilizing a fast wave antenna and RF amplifier system developed for these studies. The RF system is capable of 150 kW output power for a 1 ms pulse that is repeated at the 1 Hz repetition rate of the LAPD plasma discharge. Upon application of the RF pulse to the antenna, the DC plasma potential, measured with an emissive probe, dramatically increases in certain spatial locations by a factor greater than 10 Te. The largest plasma potentials are observed at locations magnetically connected to the top and bottom of the antenna, and they exist only in the private SOL created between the antenna and a limiter placed 3.6 m away along the LAPD axis. The DC rectified potentials scale linearly with the antenna current over a factor of 12x in the applied current. These DC potentials increase plasma materials interactions (PMI), resulting in the sputtering of antenna materials whose presence is detected in the bulk plasma by the coatings that develop on probe diagnostics. The DC rectified potentials persist in the plasma long after the RF current in the antenna has rung down on the same time scales as the change in the density. At the top and bottom of the antenna are circular flows, often

Field line diversion properties of finite β Helias equilibria

International Nuclear Information System (INIS)

Hayashi, T.; Schwenn, U.; Strumberger, E.

1992-03-01

The diversion properties of the magnetic field outside the last closed magnetic surface of a Helias stellarator configuration are investigated for finite β-equilibria. The results support a divertor concept which has been developed from the diversion properties of the corresponding vacuum field. Cross-field transport is simulated by a simplified scrape-off layer (SOL) model. (author)

Edge density profiles in high-performance JET plasmas

International Nuclear Information System (INIS)

Summers, D.D.R.; Viaccoz, B.; Vince, J.

1997-01-01

Detailed electron density profiles of the scrape-off layer in high-performance JET plasmas (plasma current, I p nbi ∝17 MW) have been measured by means of a lithium beam diagnostic system featuring high spatial resolution [Kadota (1978)[. Measurements were taken over a period of several seconds, allowing examination of the evolution of the edge profile at a location upstream from the divertor target. The data clearly show the effects of the H-mode transition - an increase in density near the plasma separatrix and a reduction in density scrape-off length. The profiles obtained under various plasma conditions are compared firstly with data from other diagnostics, located elsewhere in the vessel, and also with the predictions of an 'onion-skin' model (DIVIMP), which used, as initial parameters, data from an array of probes located in the divertor target. (orig.)

Interaction of stochastic boundary layer with plasma facing components

International Nuclear Information System (INIS)

Nguyen, F.; Ghendrih, P.; Grosman, A.

1997-01-01

To alleviate the plasma-wall interaction problems in magnetic confinement devices, a stochastic layer is used at the edge of the Tore Supra tokamak (ergodic divertor). A very important point is to determine the power deposition on the plasma facing components. Two different kinds of transport can be identified in such a configuration: Stochastic transport surrounding the confined plasma, with a random walk process, and scrape-off layer (SOL) like transport, a laminar transport, near the plasma facing components. The laminar regime is investigated in terms of a simple criterion, namely that the power deposition is proportional to the radial penetration of the laminar zone flux tubes over a finite parallel length. The magnetic connection properties of the first wall components are then determined. The connection lengths are quantified with two characteristic scales. The larger corresponds to one poloidal turn and appears to be the characteristic parallel length for laminar transport. A field line tracing code MASTOC (magnetic stochastic configuration) is used to computer the complex topology and the statistics of the connection in the real tokamak geometry. The numerical simulations are then compared with the experimental heat deposition on the modules and neutralizer plates of the Tore Supra ergodic divertor. Good agreement is found. Further evidence of laminar transport is also provided by the tangential view of such structures revealed from H α structures in detached plasma experiments. (author). 27 refs, 14 figs

Investigation of electron parallel pressure balance in the scrape-off layer of deuterium-based radiative divertor discharges IN DIII-D

International Nuclear Information System (INIS)

Petrie, T.W.; Carlstrom, T.N.; Allen, S.L.

1996-10-01

Electron density, temperature, and parallel pressure measurements at several locations along field lines connecting the midplane scrapeoff layer (SOL) with the outer divertor are presented for both attached and partially-detached divertor cases: I p = 1.4 MA, q 95 = 4.2, and P input ∼ 6.7 MW under ELMing H-mode conditions. At the onset of the Partially Detached Divertor (PDD), a high density, low temperature plasma forms in the divertor SOL (divertor MARFE). The electron pressure drops by a factor of ∼ 2 between the midplane separatrix and the X-point, and then an additional ∼3--5 times between the X-point and the outboard separatrix strike point. These results are in contrast to the attached (non-PDD) case, where electron pressure in the SOL is reduced by, at most, a factor of two between the midplane and the divertor target. Divertor MARFEs generally have only marginal adverse impact on important H-mode characteristics, such as confinement time. In fact, PDD discharges at low input power maintains good H-mode characteristics until a high density, low temperature plasma abruptly forms inside the separatrix near the X-point (X-point MARFE). Concurrent with the appearance of this X-point MARFE is a degradation in both energy confinement and the plasma fueling rate, and an increase in the carbon impurity concentration inside the core plasma. The formation of the X-point MARFE is consistent with a thermal instability resulting from the temperature dependence of the carbon radiative cooling rate in the range ∼ 7--30 eV

Atomic Layer Etching of Silicon to Solve ARDE-Selectivity-Profile-Uniformity Trade-Offs

Science.gov (United States)

Wang, Mingmei; Ranjan, Alok; Ventzek, Peter; Koshiishi, Akira

2014-10-01

With shrinking critical dimensions, dry etch faces more and more challenges. Minimizing each of aspect ratio dependent etching (ARDE), bowing, undercut, selectivity, and within die uniformly across a wafer are met by trading off one requirement against another. At the root of the problem is that roles radical flux, ion flux and ion energy play may be both good and bad. Increasing one parameter helps meeting one requirement but hinders meeting the other. Self-limiting processes like atomic layer etching (ALE) promise a way to escape the problem of balancing trade-offs. ALE was realized in the mid-1990s but the industrial implementation has been slow. In recent years interest in ALE has revived. We present how ARDE, bowing/selectivity trade-offs may be overcome by varying radical/ion ratio, byproduct re-deposition. We overcome many of the practical implementation issues associated with ALE by precise passivation process control. The Monte Carlo Feature Profile Model (MCFPM) is used to illustrate realistic scenarios built around an Ar/Cl2 chemistry driven etch of Si masked by SiO2. We demonstrate that ALE can achieve zero ARDE and infinite selectivity. Profile control depends on careful management of the ion energies and angles. For ALE to be realized in production environment, tight control of IAD is a necessary. Experimental results are compared with simulation results to provide context to the work.

Effects of variable-row-spacing harvesting picker platform scraping plates on cotton fiber quality and quantity

Directory of Open Access Journals (Sweden)

Cíntia Michele de Campos Baraviera

2017-06-01

Full Text Available There have been increasing demands for high-quality cotton fibers that meet the textile industry quality standards. Concurrently, there have been efforts to reduce contaminants during harvesting to reduce harvesting costs. The goal of this research was to evaluate the efficiency of the picker platform with Variable-Row-Spacing (VRS for harvesting cotton in narrow rows, over two harvest seasons in two regions within the state of Mato Grosso, Brazil. In this study, how the presence vs. absence of scraping plates and variations in travel speed was related to quantifiable levels of impurities the harvested fibers was examined. The research was divided into three experiments (Exp. I, II, and III, using cotton varieties FM 975 WS, IMA 5672 B2 RF, and IMA 5675 B2 RF, with row spacing of 0.45 m. The experimental design was randomized blocks, in a 2 ? 3 factorial design, using the presence/absence of the plate and three speeds (0.61, 1.0, and 1.42 m·s-¹, with seven repetitions, totaling 42 experimental plots. The plot size was 108 m² (3.6 ? 30 m. The data were analyzed using the F test in ANOVA and the post-hoc Tukey test (p < 0.05. The results showed that scraping plates increased the number of stems and cones, and reduced the harvest efficiency of cotton planted in narrow rows in the region of Sorriso-MT during the 2013/2014 harvest. For the 2014/2015 harvest, the highest speed and the presence of the scraping plates increased the number of cones in the cotton samples. In the experiment conducted in Serra da Petrovina, the removal of the scraping plates decreased the amount of cones in the harvested cotton.

Three-dimensional simulation of H-mode plasmas with localized divertor impurity injection on Alcator C-Mod using the edge transport code EMC3-EIRENE

International Nuclear Information System (INIS)

Lore, J. D.; Reinke, M. L.; Lipschultz, B.; Brunner, D.; LaBombard, B.; Terry, J.; Pitts, R. A.; Feng, Y.

2015-01-01

Experiments in Alcator C-Mod to assess the level of toroidal asymmetry in divertor conditions resulting from poloidally and toroidally localized extrinsic impurity gas seeding show a weak toroidal peaking (∼1.1) in divertor electron temperatures for high-power enhanced D-alpha H-mode plasmas. This is in contrast to similar experiments in Ohmically heated L-mode plasmas, which showed a clear toroidal modulation in the divertor electron temperature. Modeling of these experiments using the 3D edge transport code EMC3-EIRENE [Y. Feng et al., J. Nucl. Mater. 241, 930 (1997)] qualitatively reproduces these trends, and indicates that the different response in the simulations is due to the ionization location of the injected nitrogen. Low electron temperatures in the private flux region (PFR) in L-mode result in a PFR plasma that is nearly transparent to neutral nitrogen, while in H-mode the impurities are ionized in close proximity to the injection location, with this latter case yielding a largely axisymmetric radiation pattern in the scrape-off-layer. The consequences for the ITER gas injection system are discussed. Quantitative agreement with the experiment is lacking in some areas, suggesting potential areas for improving the physics model in EMC3-EIRENE

Detecting cervical cancer by quantitative promoter hypermethylation assay on cervical scrapings : A feasibility study

NARCIS (Netherlands)

Reesink-Peters, N; Wisman, G.B.A.; Jeronimo, C; Tokumaru, CY; Cohen, Y; Dong, SM; Klip, HG; Buikema, HJ; Suurmeijer, AJH; Hollema, H; Boezen, HM; Sidransky, D; van der Zee, AGJ

Current morphology-based cervical cancer screening is associated with significant false-positive and false-negative results. Tumor suppressor gene hypermethylation is frequently present in cervical cancer. It is unknown whether a cervical scraping reflects the methylation status of the underlying

Local electric field screening in bi-layer graphene devices

Directory of Open Access Journals (Sweden)

Vishal ePanchal

2014-02-01

Full Text Available We present experimental studies of both local and macroscopic electrical effects in uniform single- (1LG and bi-layer graphene (2LG devices as well as in devices with non-uniform graphene coverage, under ambient conditions. DC transport measurements on sub-micron scale Hall bar devices were used to show a linear rise in carrier density with increasing amounts of 2LG coverage. Electrical scanning gate microscopy was used to locally top gate uniform and non-uniform devices in order to observe the effect of local electrical gating. We experimentally show a significant level of electric field screening by 2LG. We demonstrate that SGM technique is an extremely useful research tool for studies of local screening effects, which provides a complementary view on phenomena that are usually considered only within a macroscopic experimental scheme.

Localization of multilayer networks by optimized single-layer rewiring.

Science.gov (United States)

Jalan, Sarika; Pradhan, Priodyuti

2018-04-01

We study localization properties of principal eigenvectors (PEVs) of multilayer networks (MNs). Starting with a multilayer network corresponding to a delocalized PEV, we rewire the network edges using an optimization technique such that the PEV of the rewired multilayer network becomes more localized. The framework allows us to scrutinize structural and spectral properties of the networks at various localization points during the rewiring process. We show that rewiring only one layer is enough to attain a MN having a highly localized PEV. Our investigation reveals that a single edge rewiring of the optimized MN can lead to the complete delocalization of a highly localized PEV. This sensitivity in the localization behavior of PEVs is accompanied with the second largest eigenvalue lying very close to the largest one. This observation opens an avenue to gain a deeper insight into the origin of PEV localization of networks. Furthermore, analysis of multilayer networks constructed using real-world social and biological data shows that the localization properties of these real-world multilayer networks are in good agreement with the simulation results for the model multilayer network. This paper is relevant to applications that require understanding propagation of perturbation in multilayer networks.

Multi-layered pallet and production method and device therefor

International Nuclear Information System (INIS)

Sudo, Shigeru.

1995-01-01

The present invention concerns the production of a solid tritium pellet for use in a thermonuclear reactor. A first pellet constituent material constituting an outer layer of the pellet is solidified under cooling to form a solidification product for the pellet. A cave is formed on one end face of the pellet solidification product. A second pellet constituent material constituting an inner layer of the pellet is supplied and solidified under cooling. After scraping a predetermined amount of the other end face of the pellet solidification material, the first pellet constituent material is additionally supplied and solidified under cooling. The size and the relative position of each of layers can be determined definitely and the inner layer can be formed reliably while fuels can be accurately supplied with no loss to a required portion in plasma. (N.H.)

Controlling the layer localization of gapless states in bilayer graphene with a gate voltage

Science.gov (United States)

Jaskólski, W.; Pelc, M.; Bryant, Garnett W.; Chico, Leonor; Ayuela, A.

2018-04-01

Experiments in gated bilayer graphene with stacking domain walls present topological gapless states protected by no-valley mixing. Here we research these states under gate voltages using atomistic models, which allow us to elucidate their origin. We find that the gate potential controls the layer localization of the two states, which switches non-trivially between layers depending on the applied gate voltage magnitude. We also show how these bilayer gapless states arise from bands of single-layer graphene by analyzing the formation of carbon bonds between layers. Based on this analysis we provide a model Hamiltonian with analytical solutions, which explains the layer localization as a function of the ratio between the applied potential and interlayer hopping. Our results open a route for the manipulation of gapless states in electronic devices, analogous to the proposed writing and reading memories in topological insulators.

Layer-by-layer modification of thin-film metal-semiconductor multilayers with ultrashort laser pulses

Science.gov (United States)

Romashevskiy, S. A.; Tsygankov, P. A.; Ashitkov, S. I.; Agranat, M. B.

2018-05-01

The surface modifications in a multilayer thin-film structure (50-nm alternating layers of Si and Al) induced by a single Gaussian-shaped femtosecond laser pulse (350 fs, 1028 nm) in the air are investigated by means of atomic-force microscopy (AFM), scanning electron microscopy (SEM), and optical microscopy (OM). Depending on the laser fluence, various modifications of nanometer-scale metal and semiconductor layers, including localized formation of silicon/aluminum nanofoams and layer-by-layer removal, are found. While the nanofoams with cell sizes in the range of tens to hundreds of nanometers are produced only in the two top layers, layer-by-layer removal is observed for the four top layers under single pulse irradiation. The 50-nm films of the multilayer structure are found to be separated at their interfaces, resulting in a selective removal of several top layers (up to 4) in the form of step-like (concentric) craters. The observed phenomenon is associated with a thermo-mechanical ablation mechanism that results in splitting off at film-film interface, where the adhesion force is less than the bulk strength of the used materials, revealing linear dependence of threshold fluences on the film thickness.

Lyapunov spectra of density fluctuations in TBR-1

International Nuclear Information System (INIS)

Oiwa, N.N.; Fidler-Ferrara, N.

1993-01-01

The results for the Lyapunov exponents associated with density fluctuations measured by Langmuir probes placed in the scrape-off layer of the Tokamak TBR-1 are reported. By a judicious use of the Sano-Sawada and Eckmann-Ruelle algorithms conclusive values for the positive Lyapunov exponents for most of the analysed signals are used showing evidences of chaotic behavior. (author)

Macular Ganglion Cell Inner Plexiform Layer Thickness in Glaucomatous Eyes with Localized Retinal Nerve Fiber Layer Defects.

Directory of Open Access Journals (Sweden)

Chunwei Zhang

Full Text Available To investigate macular ganglion cell-inner plexiform layer (mGCIPL thickness in glaucomatous eyes with visible localized retinal nerve fiber layer (RNFL defects on stereophotographs.112 healthy and 149 glaucomatous eyes from the Diagnostic Innovations in Glaucoma Study (DIGS and the African Descent and Glaucoma Evaluation Study (ADAGES subjects had standard automated perimetry (SAP, optical coherence tomography (OCT imaging of the macula and optic nerve head, and stereoscopic optic disc photography. Masked observers identified localized RNFL defects by grading of stereophotographs.47 eyes had visible localized RNFL defects on stereophotographs. Eyes with visible localized RNFL defects had significantly thinner mGCIPL thickness compared to healthy eyes (68.3 ± 11.4 μm versus 79.2 ± 6.6 μm respectively, P<0.001 and similar mGCIPL thickness to glaucomatous eyes without localized RNFL defects (68.6 ± 11.2 μm, P = 1.000. The average mGCIPL thickness in eyes with RNFL defects was 14% less than similarly aged healthy controls. For 29 eyes with a visible RNFL defect in just one hemiretina (superior or inferior mGCIPL was thinnest in the same hemiretina in 26 eyes (90%. Eyes with inferior-temporal RNFL defects also had significantly thinner inferior-temporal mGCIPL (P<0.001 and inferior mGCIPL (P = 0.030 compared to glaucomatous eyes without a visible RNFL defect.The current study indicates that presence of a localized RNFL defect is likely to indicate significant macular damage, particularly in the region of the macular that topographically corresponds to the location of the RNFL defect.

Transfer of metallic debris from the metal surface of an acetabular cup to artificial femoral heads by scraping: comparison between alumina and cobalt-chrome heads.

Science.gov (United States)

Chang, Chong Bum; Yoo, Jeong Joon; Song, Won Seok; Kim, Deug Joong; Koo, Kyung-Hoi; Kim, Hee Joong

2008-04-01

We aimed to investigate the transfer of metal to both ceramic (alumina) and metal (cobalt-chrome) heads that were scraped by a titanium alloy surface under different load conditions. The ceramic and metal heads for total hip arthroplasties were scraped by an acetabular metal shell under various loads using a creep tester. Microstructural changes in the scraped area were visualized with a scanning electron microscope, and chemical element changes were assessed using an energy dispersive X-ray spectrometry. Changes in the roughness of the scraped surface were evaluated by a three-dimensional surface profiling system. Metal transfer to the ceramic and metal heads began to be detectable at a 10 kg load, which could be exerted by one-handed force. The surface roughness values significantly increased with increasing test loads in both heads. When the contact force increased, scratching of the head surface occurred in addition to the transfer of metal. The results documented that metallic debris was transferred from the titanium alloy acetabular shell to both ceramic and metal heads by minor scraping. This study suggests that the greatest possible effort should be made to protect femoral heads, regardless of material, from contact with metallic surfaces during total hip arthroplasty.

Using an ultra-thin non-doped orange emission layer to realize high efficiency white organic light-emitting diodes with low efficiency roll-off

Energy Technology Data Exchange (ETDEWEB)

Zhu, Liping; Chen, Jiangshan; Ma, Dongge, E-mail: mdg1014@ciac.ac.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Graduate University of the Chinese Academy of Sciences, Changchun 130022 (China); Zhao, Yongbiao [Luminous Center of Excellence for Semiconductor Lighting and Displays, School of Electrical and Electronic Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore, Singapore 639798 (Singapore); Zhang, Hongmei [Department of Materials Science and Engineering, Nanjing University of Posts and Telecommunications, Nanjing 210023 (China)

2014-06-28

By adopting an ultra-thin non-doped orange emission layer sandwiched between two blue emission layers, high efficiency white organic light-emitting diodes (WOLEDs) with reduced efficiency roll-off were fabricated. The optimized devices show a balanced white emission with Internationale de L'Eclairage of (0.41, 0.44) at the luminance of 1000 cd/m{sup 2}, and the maximum power efficiency, current efficiency (CE), and external quantum efficiency reach 63.2 lm/W, 59.3 cd/A, and 23.1%, which slightly shift to 53.4 lm/W, 57.1 cd/A, and 22.2% at 1000 cd/m{sup 2}, respectively, showing low efficiency roll-off. Detailed investigations on the recombination zone and the transient electroluminescence (EL) clearly reveal the EL processes of the ultra-thin non-doped orange emission layer in WOLEDs.

Addressing the efficiency roll-off in a fluorescent OLED by facile electron transport layer doping and carrier confinement

Science.gov (United States)

Soman, Anjaly; M, Manuraj; Unni, K. N. Narayanan

2018-05-01

Organic light emitting diodes (OLEDs) often face the issue of decreasing power efficiency with increasing brightness. Loss of charge carrier balance is one of the factors contributing to the efficiency roll-off. We demonstrate that by using a combination of doped electron transport layer (ETL) and a specially chosen electron blocking layer (EBL) having high hole mobility, this efficiency roll-off can be effectively suppressed. A tris-(8-hydroxyquinoline) aluminium (Alq3) based OLED has been fabricated with 2,3,6,7-Tetrahydro-1,1,7,7,-tetramethyl-1H, 5H,11H-10-(2-benzothiazolyl) quinolizino-[9,9a, 1n gh]coumarin (C545T) as the emissive dopant. Bulk doping of the ETL with lithium fluoride (LiF) was optimized to increase the luminous intensity as well as the current efficiency. An EBL with high hole mobility introduced between the EML and the hole transport layer (HTL) improved the performance drastically, and the device brightness at 9 V got improved by a factor of 2.5 compared to that of the control device. While increasing the brightness from 100 cd/m2 to 1000 cd/m2, the power efficiency drop was 47% for the control device whereas only a drop of 15% was observed for the modified device. The possible mechanisms for the enhanced performance are discussed.

d-PET-controlled “off-on” Polarity-sensitive Probes for Reporting Local Hydrophilicity within Lysosomes

Science.gov (United States)

Zhu, Hao; Fan, Jiangli; Mu, Huiying; Zhu, Tao; Zhang, Zhen; Du, Jianjun; Peng, Xiaojun

2016-10-01

Polarity-sensitive fluorescent probes are powerful chemical tools for studying biomolecular structures and activities both in vitro and in vivo. However, the lack of “off-on” polarity-sensing probes has limited the accurate monitoring of biological processes that involve an increase in local hydrophilicity. Here, we design and synthesize a series of “off-on” polarity-sensitive fluorescent probes BP series consisting of the difluoroboron dippyomethene (BODIPY) fluorophore connected to a quaternary ammonium moiety via different carbon linkers. All these probes showed low fluorescence quantum yields in nonpolar solution but became highly fluorescent in polar media. BP-2, which contains a two-carbon linker and a trimethyl quaternary ammonium, displayed a fluorescence intensity and quantum yield that were both linearly correlated with solvent polarity. In addition, BP-2 exhibited high sensitivity and selectivity for polarity over other environmental factors and a variety of biologically relevant species. BP-2 can be synthesized readily via an unusual Mannich reaction followed by methylation. Using electrochemistry combined with theoretical calculations, we demonstrated that the “off-on” sensing behavior of BP-2 is primarily due to the polarity-dependent donor-excited photoinduced electron transfer (d-PET) effect. Live-cell imaging established that BP-2 enables the detection of local hydrophilicity within lysosomes under conditions of lysosomal dysfunction.

Physical study of experimental fusion breeder FEB divertor

International Nuclear Information System (INIS)

Zhu Yukun; Zhou Xiaobing; Huang Jinhua; Feng Kaiming; Deng Peizhi; Huo Tiejun

1999-10-01

The physical study of FEB divertor is presented. In order to improve the impurity control and increase ion-neutral interactions in the divertor, the configuration of the divertor is optimized to be the close type in the engineering design activity compared with the open type in the early conceptual activity. The operation mode of the divertor is designed to be partial detached plasma mode under conditions of combination gas-puffing with impurity injection. The position of gas-puffing is optimized to be at the torus mid-plane with NEWT1D code from the viewpoint of impurity retention and radiation in the scrape-off layer/divertor region. Boron is chosen as the injected impurity. The effect of boron impurity injection is evaluated from the reduced heat load on the divertor target. The plasma pressure drop along the scrape-off layer/divertor region is estimated with the two-point transport model and impurity radiation model in the dynamic gas target concept. The simulation results show that the plasma pressure drop factor f p is not only related to the radiation fraction f rad but also related greatly to the stagnation point density n s

Assessment of feasibility of helium ash exhaust and heat removal by pumped-limiter in tokamak fusion reactor

International Nuclear Information System (INIS)

Hitoki, Shigehisa; Sugihara, Masayoshi; Saito, Seiji; Fujisawa, Noboru

1985-01-01

A detailed calculation of the behavior of fuel and He particles in tokamak reactor with pumped-limiter is performed by one-dimensional tokamak transport code. Energy of neutral particles flowing back from limiter chamber is calculated by two-dimensional Monte Carlo neutral code. Feasibility of He ash exhaust and heat removal by the pumped-limiter are analyzed. Following features of the pumped-limiter are clarified: (1) Electron temperature decays rapidly in radial direction in scrape-off layer, while density profile is broader than that of temperature. (2) Helium accumulation in main plasma can be kept at desired level by rather short limiter and moderate pumping system. (3) Minimum amount of tritium pumped out little depends on limiter length. (4) Although high temperature plasma in scrape-off layer could be realized by large pumping and ideal pellet injection, it is not sufficiently high to reduce the erosion of the limiter surface and the leading edge. In conclusion, He ash exhaust may be possible by the pumped-limiter, while the heat load and erosion will be so high that the pumped-limiter may not be applicable unless the boundary plasma is cooled by radiation or by some other means. (author)

Development of off-line layer chromatographic and total reflection X-ray fluorescence spectrometric methods for arsenic speciation

International Nuclear Information System (INIS)

Mihucz, Victor G.; Moricz, Agnes M.; Kroepfl, Krisztina; Szikora, Szilvia; Tatar, Eniko; Parra, Lue Meru Marco; Zaray, Gyula

2006-01-01

Rapid and low cost off-line thin layer chromatography-total reflection X-ray fluorescence spectrometry and overpressured thin layer chromatography-total reflection X-ray fluorescence spectrometry methods have been developed for separation of 25 ng of each As(III), As(V), monomethyl arsonic acid and dimethylarsinic acid applying a PEI cellulose stationary phase on plastic sheets and a mixture of acetone/acetic acid/water = 2:1:1 (v/v/v) as eluent system. The type of eluent systems, the amounts (25-1000 ng) of As species applied to PEI cellulose plates, injection volume, development distance, and flow rate (in case of overpressured thin layer chromatography) were taken into consideration for the development of the chromatographic separation. Moreover, a microdigestion method employing nitric acid for the As spots containing PEI cellulose scratched from the developed plates divided into segments was developed for the subsequent total reflection X-ray fluorescence spectrometry analysis. The method was applied for analysis of root extracts of cucumber plants grown in As(III) containing modified Hoagland nutrient solution. Both As(III) and As(V) were detected by applying the proposed thin layer chromatography/overpressured thin layer chromatography-total reflection X-ray fluorescence spectrometry methods

Development of off-line layer chromatographic and total reflection X-ray fluorescence spectrometric methods for arsenic speciation

Energy Technology Data Exchange (ETDEWEB)

Mihucz, Victor G. [Joint Research Group of Environmental Chemistry of Hungarian Academy of Sciences and L. Eoetvoes University, P. O. Box 32, H-1518 Budapest (Hungary); Hungarian Satellite Centre of Trace Elements Institute to UNESCO, P. O. Box 32, H-1518 Budapest (Hungary); Moricz, Agnes M. [L. Eoetvoes University, Department of Chemical Technology and Environmental Chemistry, P.O. Box 32, H-1518 Budapest (Hungary); Kroepfl, Krisztina [Joint Research Group of Environmental Chemistry of Hungarian Academy of Sciences and L. Eoetvoes University, P. O. Box 32, H-1518 Budapest (Hungary); Szikora, Szilvia [Joint Research Group of Environmental Chemistry of Hungarian Academy of Sciences and L. Eoetvoes University, P. O. Box 32, H-1518 Budapest (Hungary); Tatar, Eniko [Hungarian Satellite Centre of Trace Elements Institute to UNESCO, P. O. Box 32, H-1518 Budapest (Hungary); L. Eoetvoes University, Department of Inorganic and Analytical Chemistry, P.O. Box 32, H-1518 Budapest (Hungary); Parra, Lue Meru Marco [Universidad Centro-occidental Lisandro Alvarado, Decanato de Agronomia, Departamento de Quimica y Suelos Unidad de Analisis Instrumental, Apartado Postal 4076, Cabudare 3023 (Venezuela); Zaray, Gyula [Joint Research Group of Environmental Chemistry of Hungarian Academy of Sciences and L. Eoetvoes University, P. O. Box 32, H-1518 Budapest (Hungary) and Hungarian Satellite Centre of Trace Elements Institute to UNESCO, P. O. Box 32, H-1518 Budapest (Hungary) and L. Eoetvoes University, Department of Inorganic and Analytical Chemistry, P.O. Box 32, H-1518 Budapest (Hungary)]. E-mail: zaray@ludens.elte.hu

2006-11-15

Rapid and low cost off-line thin layer chromatography-total reflection X-ray fluorescence spectrometry and overpressured thin layer chromatography-total reflection X-ray fluorescence spectrometry methods have been developed for separation of 25 ng of each As(III), As(V), monomethyl arsonic acid and dimethylarsinic acid applying a PEI cellulose stationary phase on plastic sheets and a mixture of acetone/acetic acid/water = 2:1:1 (v/v/v) as eluent system. The type of eluent systems, the amounts (25-1000 ng) of As species applied to PEI cellulose plates, injection volume, development distance, and flow rate (in case of overpressured thin layer chromatography) were taken into consideration for the development of the chromatographic separation. Moreover, a microdigestion method employing nitric acid for the As spots containing PEI cellulose scratched from the developed plates divided into segments was developed for the subsequent total reflection X-ray fluorescence spectrometry analysis. The method was applied for analysis of root extracts of cucumber plants grown in As(III) containing modified Hoagland nutrient solution. Both As(III) and As(V) were detected by applying the proposed thin layer chromatography/overpressured thin layer chromatography-total reflection X-ray fluorescence spectrometry methods.

Localized removal of layers of metal, polymer, or biomaterial by ultrasound cavitation bubbles

NARCIS (Netherlands)

Rivas, David Fernandez; Verhaagen, Bram; Seddon, James R. T.; Zijlstra, Aaldert G.; Jiang, Lei-Meng; van der Sluis, Luc W. M.; Versluis, Michel; Lohse, Detlef; Gardeniers, Han J. G. E.

We present an ultrasonic device with the ability to locally remove deposited layers from a glass slide in a controlled and rapid manner. The cleaning takes place as the result of cavitating bubbles near the deposited layers and not due to acoustic streaming. The bubbles are ejected from air-filled

Localized removal of layers of metal, polymer, or biomaterial by ultrasound cavitation bubbles

NARCIS (Netherlands)

Fernandez Rivas, David; Verhaagen, B.; Seddon, James Richard Thorley; Zijlstra, A.G.; Jiang, L.M.; van der Sluis, L.W.M.; Versluis, Michel; Lohse, Detlef; Gardeniers, Johannes G.E.

2012-01-01

We present an ultrasonic device with the ability to locally remove deposited layers from a glass slide in a controlled and rapid manner. The cleaning takes place as the result of cavitating bubbles near the deposited layers and not due to acoustic streaming. The bubbles are ejected from air-filled

Investigation of particle lift off in a turbulent boundary layer

Science.gov (United States)

Barros, Diogo; Tee, Yi Hui; Morse, Nicholas; Hiltbrand, Ben; Longmire, Ellen

2017-11-01

Entrainment and suspension of particles within turbulent flows occur widely in environmental and industrial processes. Three-dimensional particle tracking experiments are thus conducted in a water channel to understand the interaction of finite-size particles with a turbulent boundary layer. A neutrally buoyant sphere made of wax and iron oxide is first held in place on the bounding surface by a magnet before being released and tracked. The sphere is marked with dots to monitor rotation as well as translation. By setting up two pairs of cameras in a stereoscopic configuration, the trajectories of the sphere are reconstructed and tracked over a distance of 4 to 6 δ. Sphere diameters ranging from 40 to 130 wall units, initial particle Reynolds numbers of 600 to 2000 and friction Reynolds numbers of 500 to 1800 are considered. For this parameter set, the particle typically lifts off from the wall after release before falling back toward the wall. Aspects of both particle rotation and translation will be discussed. Supported by NSF (CBET-1510154).

Scraping technique of stuck needle at Anmian point in the treatment of insomnia: a randomized controlled trial

Institute of Scientific and Technical Information of China (English)

张全爱

2013-01-01

Objective To compare the efficacy difference in the treatment of insomnia between scraping technique of stuck needle and conventional acupuncture at Anmian (Extra) .Methods One hundred and thirty one cases

Response to comment on 'Magnetic topology effects on Alcator C-Mod scrape-off layer flow'

International Nuclear Information System (INIS)

Simakov, Andrei N; Catto, Peter J

2009-01-01

In his comment to our recent work (Simakov et al 2008 Plasma Phys. Control. Fusion 50 105010), Aydemir has asserted that poloidal plasma flow reversal is not a valid response to toroidal magnetic field reversal in an up-down symmetric tokamak, and that the toroidal plasma flow must reverse instead. We show that this assertion is wrong due to his misunderstanding of the corresponding symmetry transformation. (reply)

Spatially resolved characterization of electrostatic fluctuations in the scrape-off layer of the CASTOR tokamak

Czech Academy of Sciences Publication Activity Database

Devynck, P.; Bonhomme, G.; Martines, E.; Stöckel, Jan; Van Oost, G.; Voitsekhovitch, I.; Adámek, Jiří; Azeroual, A.; Doveil, F.; Ďuran, Ivan; Gravier, E.; Gunn, J.; Hron, Martin

2005-01-01

Roč. 47, č. 2 (2005), s. 269-280 ISSN 0741-3335 R&D Projects: GA ČR GA202/03/0786 Grant - others:GA - INTAS 2001 2056 Institutional research plan: CEZ:AV0Z20430508 Keywords : tokamak * plasma * turbulence Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.902, year: 2005

Measurements of scrape-off layer ion-to-electron temperature ratio in Tore Supra ohmic plasmas

Czech Academy of Sciences Publication Activity Database

Kočan, M.; Gunn, J. P.; Pascal, J.-Y.; Bonhomme, G.; Devynck, P.; Ďuran, Ivan; Gauthier, E.; Ghendrih, P.; Marandet, Y.; Pegourie, B.; Vallet, J.-C.

390-391, - (2009), s. 1074-1077 ISSN 0022-3115. [International Conference on Plasma-Surface Interactions in Controlled Fusion Devices/18th./. Toledo, 26.05.2008-30.05. 2008] Institutional research plan: CEZ:AV0Z20430508 Keywords : Ion temperature * Electron temperature * Edge plasma * Tore Supra Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 1.933, year: 2009

Characteristics of the FTU scrape-off layer (SOL) determined by a simple 1-D model

International Nuclear Information System (INIS)

Ferro, C.

1994-12-01

A simple 1-D model analytical model has been developed to determine the SOL characteristics from the parameters of the main plasma. The solutions are compared with FTU experimental data. The solutions fit quite well the experimental data and their trend. Moreover the model suggests the presence of a critical density related to the non isothermal power flux and the corresponding maximum power which can be safely removed by volumetric sinks. Differences between a limiter-like configuration and a divertor-like configuration are described

Turbulence and transport with spatial-temporal biasing on the scrape-off layer on CASTOR tokamak

International Nuclear Information System (INIS)

Stoeckel, J.

2002-01-01

Experiments with the poloidal ring of 32 plane electrodes were performed on the CASTOR tokamak (R=0.4 m, a=0.06 m, B=1 T) to measure, for the first time, the complete poloidal structure of the electrostatic edge turbulence. In addition, the possibility of active modification of the edge turbulence was checked. The main results are as follows: Quite regular turbulent structures with the pronounced poloidal periodicity are observed by passive measuring signals of the individual electrodes. The dominant poloidal mode number, m=6-8, is approximately of the same value as the edge safety factor. Propagating waves of potential (f=10-40 kHz) with the wave numbers in the range of m=2-8, applied to the ring of the electrodes, modify the edge turbulence significantly due to their interaction with turbulent structures. (author)

Derivation of stochastic differential equations for scrape-off layer plasma fluctuations from experimentally measured statistics

Energy Technology Data Exchange (ETDEWEB)

Mekkaoui, Abdessamad [IEK-4 Forschungszentrum Juelich 52428 (Germany)

2013-07-01

A method to derive stochastic differential equations for intermittent plasma density dynamics in magnetic fusion edge plasma is presented. It uses a measured first four moments (mean, variance, Skewness and Kurtosis) and the correlation time of turbulence to write a Pearson equation for the probability distribution function of fluctuations. The Fokker-Planck equation is then used to derive a Langevin equation for the plasma density fluctuations. A theoretical expectations are used as a constraints to fix the nonlinearity structure of the stochastic differential equation. In particular when the quadratically nonlinear dynamics is assumed, then it is shown that the plasma density is driven by a multiplicative Wiener process and evolves on the turbulence correlation time scale, while the linear growth is quadratically damped by the fluctuation level. Strong criteria for statistical discrimination of experimental time series are proposed as an alternative to the Kurtosis-Skewness scaling. This scaling is broadly used in contemporary literature to characterize edge turbulence, but it is inappropriate because a large family of distributions could share this scaling. Strong criteria allow us to focus on the relevant candidate distribution and approach a nonlinear structure of edge turbulence model.

Field line diversion properties of finite β-helias equilibria

International Nuclear Information System (INIS)

Hayashi, Takaya; Schwenn, Ulrich; Strumberger, Erika.

1992-01-01

The diversion properties of the magnetic field outside the last closed magnetic surface of a Helias stellarator configuration are investigated for finite pressure equilibria. The results indicate that a divertor concept which has been developed from the diversion properties of the corresponding vacuum field can be maintained for finite pressure equilibria. Cross-field particle transport is simulated by a simplified scrape-off layer (SOL) model. (author)

Numerical simulation of feedback stabilization of axisymmetric modes in tokamaks using driven halo currents

International Nuclear Information System (INIS)

Jardin, S.C.; Schmidt, J.A.

1998-01-01

The Tokamak Simulation Code (TSC) has been used to model a new method of feedback stabilization of the axisymmetric instability in tokamaks using driven halo (or scrape-off layer) currents. The method appears to be feasible for a wide range of plasma edge parameters. It may offer advantages over the more conventional method of controlling this instability when applied in a reactor environment. (author)

Recent results in the DIVA experiment

International Nuclear Information System (INIS)

1978-03-01

Divertor effects have been studied over a wide range of plasma parameters: electron temperature T sub(eo) = 200 - 700 eV, ion temperature T sub(io) = 60 - 300 eV and density n sub(eo) = (1.5 - 8.0) x 10 13 cm -3 in the main plasma, and T sub(es) = 20 - 100 eV, T sub(is) = 20 - 60 eV and n sub(es) = (1.5 - 5.0) x 10 12 cm -3 in the scrape-off layer plasma. The following results are obtained. 1) The divertor reduces plasma-wall interactions near the main plasma by guiding loss plasma into the divertor chamber. A maximum divertor efficiency is 35% for particle flux and 75% for heat flux. 2) The scrape-off layer plasma shields impurity influx, guides ionized impurities into the divertor, and reduces influx of injected impurities into the main plasma by a factor of 2 - 4. Shielding efficiency is higher for aluminum than for carbon. Shielding effect is also observed in a conventional discharge. 3) The divertor reduces radiation loss by a factor of 2 - 4 and hence increases the energy-confinement time by a factor of 2.5. 4) The divertor does not significantly affect particle-confinement time, ion temperature and heat diffusion coefficient. 5) The radiation loss due to pseudo continuum mainly from gold ions is comparable to that due to oxygen lines. Impurity confinement time is comparable to the average particle-confinement time. 6) The particle flow velocity is a few times less than the sound velocity, the heat transmission rate is consistent with a sheath model, and the particle diffusion coefficient in the scrape-off layer is about ten times less than the Bohm diffusion coefficient. Scaling for electron temperature is obtained. 7) Ion sputtering, arcing and evaporation are identified. The ion sputtering by impurity ions is the dominant process of metallic impurity release from a limiter or a neutralizer plate in a stable discharge. (J.P.N.)

Localization of excitons by molecular layer formation in a polymer film

International Nuclear Information System (INIS)

Chattopadhyay, S.; Datta, A.

2005-01-01

Spin coated films of atactic polystyrene of two different molecular weights have been studied with uv spectroscopy and x-ray reflectivity, the film thickness (d) varying from ∼2R g to ∼12R g where R g is the unperturbed radius of gyration of the polymer. uv extinction due to the pure electronic singlet 1 A 1g → 1 E 1u is seen to increase with d -1 for 4R g ≤d≤12R g (region 1). This suggests excitonic interaction along d. The variation of total exciton energy (E) of the A 1g →E 1u singlet with d in region 1 can be well explained by formation of linear J-aggregates of polystyrene molecules, in a lattice with spacing 'a' (in A) R g g , along d. Atomic force microscopic images of the films show the presence of 'spheres' distributed randomly on film surfaces with in-plane dimensions matching a. From the variation of E with d -2 the effective mass (m eff ) of the exciton is also determined. For R g g (region 2) the extinction and E become essentially independent of d, indicating exciton localization along d, and the value of m eff becomes very large. This enhancement in the effective mass maybe used to quantify localization. The variations of electron density (ρ) with d, i.e., the electron density profiles (EDPs) of the films extracted from x-ray reflectivity studies, indicate formation of layers with period 'b' (in A), R g g parallel to substrate surface in region 2 and a constant ρ film in region 1. On raising the temperature of a typical film to 60 deg. C, the layering was seen to almost vanish, as obtained from both the EDP and the Patterson function of the reflectivity profile. The close correspondence between 'a' and 'b' indicates that the molecules forming the J-aggregates form the layers, too. The average difference in ρ between successive extrema in the EDPs in region 2, denoted by δ, can be used as the order parameter for the layering transition. For PS-5, δ>0 at d≅4R g , where the exciton is still delocalized. Layering reduces the Hamaker

Turbulence and intermittent transport at the boundary of magnetized plasmas

DEFF Research Database (Denmark)

Garcia, O.E.; Naulin, V.; Nielsen, A.H.

2005-01-01

Numerical fluid simulations of interchange turbulence for geometry and parameters relevant to the boundary region of magnetically confined plasmas are shown to result in intermittent transport qualitatively similar to recent experimental measurements. The two-dimensional simulation domain features...... a forcing region with spatially localized sources of particles and heat outside which losses due to the motion along open magnetic-field lines dominate, corresponding to the edge region and the scrape-off layer, respectively. Turbulent states reveal intermittent eruptions of hot plasma from the edge region...... fluctuation wave forms and transport statistics are also in a good agreement with those derived from the experiments. Associated with the turbulence bursts are relaxation oscillations in the particle and heat confinements as well as in the kinetic energy of the sheared poloidal flows. The formation of blob...

A study of X-divertor in NSTX-U with SOLPS simulations

Science.gov (United States)

Chen, Zhong-Ping; Kotschenreuther, Mike; Mahajan, Swadesh; Gerhardt, Stefan

2018-03-01

The X-divertor (XD) geometry in NSTX-U is demonstrated, via SOLPS simulations, to perform better than the standard divertor (SD); in particular, it allows detachment at a lower upstream density and stabilizes the detachment front near the target, away from the main X-point. Consequently a stable detached operation becomes possible—the localization near the plate allows a vast reduction of heat fluxes without degrading the core plasma. Indeed, it is confirmed by our simulation that at similar states of detachment the XD outperforms the SD by reducing the heat fluxes to the target and maintaining higher upstream temperatures, resulting in scrape-off layers that are more favorable for advanced tokamak operation. These advantages are attributed to the unique geometric characteristics of XD—poloidal flaring near the target.

A survey of problems in divertor and edge plasma theory

International Nuclear Information System (INIS)

Boozer, A.; Braams, B.; Weitzner, H.; Hazeltine, R.; Houlberg, W.; Oktay, E.; Sadowski, W.; Wootton, A.

1992-01-01

Theoretical physics problems related to divertor design are presented, organized by the region in which they occur. Some of the open questions in edge physics are presented from a theoretician's point of view. After a cursory sketch of the fluid models of the edge plasma and their numerical realization, the following topics are taken up: time-dependent problems, non-axisymmetric effects, anomalous transport in the scrape-off layer, edge kinetic theory, sheath effects and boundary conditions in divertors, electric field effects, atomic and molecular data issues, impurity transport in the divertor region, poloidally localized power dissipation (MARFEs and dense gas targets), helium ash removal, and neutral transport. The report ends with a summary of selected problems of particular significance and a brief bibliography of survey articles and related conference proceedings

Improvement of efficiency roll-off in blue phosphorescence OLED using double dopants emissive layer

Energy Technology Data Exchange (ETDEWEB)

Yoo, Seung Il; Yoon, Ju An; Kim, Nam Ho; Kim, Jin Wook; Kang, Jin Sung; Moon, Chang-Bum [Department of Green Energy & Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Kim, Woo Young, E-mail: wykim@hoseo.edu [Department of Green Energy & Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Department of Engineering Physics, McMaster University, Hamilton, Ontario L8S 4L7 (Canada)

2015-04-15

Blue phosphorescent organic light-emitting diodes (PHOLEDs) were fabricated using double dopants FIrpic and FIr6 in emissive layer (EML) with structure of ITO/NPB (700 Å)/mCP:FIrpic-8%:FIr6-x% (300 Å)/TPBi (300 Å)/Liq (20 Å)/Al (1200 Å). We optimized concentration of the second dopant FIr6 in the presence of a fixed FIrpic to observe its effect on electrical performance of PHOLED device. 24.8 cd/A of luminous efficiency was achieved by the device with dopant ratio of 8%FIrpic:4%FIr6 in EML. Efficiency roll-off was also improved 20% compared to the PHOLED device singly dopped with FIrpic or FIr6 only. Second doping proved its effect in stabilizing charge balance in EML and enhancing energy transfer of triplet excitons between two dopants. - Highlights: • We fabricated blue PHOLED with double blue phosphorescent dopants in single EML. • Efficiency roll-off was improved by using double dopant in single EML. • The host–dopant transfer is discussed by analyzing the photo-absorption and photoluminescence. • The spectroscopic analysis using multi-peak fits with a Gaussian function.

Measurement of peripheral plasma using double probe in TRIAM-IM

International Nuclear Information System (INIS)

Yamagami, Masahiro; Kawasaki; Shoji; Jyotaki, Eriko; Fujita, Takaaki; Sakamoto, Mizuki; Nakamura, Kazuo; Nakamura, Yukio; Ito, Satoshi

1994-01-01

Behind the poloidal limiter of the TRIAM-IM, the change with time lapse of the electron temperature and the plasma density at the time of OH discharge was examined by using a double probe. Scrape-off plasma parameters, namely the correlations of electron temperature, plasma density and ion flux with main plasma parameters were obtained. It was found that scrape-off density is almost proportional to square of beam average electron density. Further, it was determined by calculation that the density on the outermost shell magnetic surface is about 1.5 x 10 15 /m 2 . In the TRIAM-IM, it is expected that accompanying the increase of plasma current at the time of OH discharge, the effects of thermal load and particle load given to the limiter and the first wall increase, and the increase of the metallic impurities due to sputtering becomes a serious problem. The merits of double probe method are explained. The objective of this experiment is to examine the temperature and density of the plasma that comes in contact with the limiter and the wall by determining the basic parameters of peripheral plasma at the time of OH discharge. In order to heighten the reliability of data, the examination was carried out from both aspects of hardware and software. The TRIAM-IM, double probe measuring system and its theory, applied voltage sweeping part, signal processing system, data processing system, and the experimental results of scrape-off layer parameters are described. (K.I.)

Local Electronic Structure of a Single-Layer Porphyrin-Containing Covalent Organic Framework

KAUST Repository

Chen, Chen; Joshi, Trinity; Li, Huifang; Chavez, Anton D.; Pedramrazi, Zahra; Liu, Pei-Nian; Li, Hong; Dichtel, William R.; Bredas, Jean-Luc; Crommie, Michael F.

2017-01-01

We have characterized the local electronic structure of a porphyrin-containing single-layer covalent organic framework (COF) exhibiting a square lattice. The COF monolayer was obtained by the deposition of 2,5-dimethoxybenzene-1,4-dicarboxaldehyde

Effect of layer-by-layer coatings and localization of antioxidant on oxidative stability of a model encapsulated bioactive compound in oil-in-water emulsions.

Science.gov (United States)

Pan, Yuanjie; Nitin, N

2015-11-01

Oxidation of encapsulated bioactives in emulsions is one of the key challenges that limit shelf-life of many emulsion containing products. This study seeks to quantify the role of layer-by-layer coatings and localization of antioxidant molecules at the emulsion interface in influencing oxidation of the encapsulated bioactives. Oxidative barrier properties of the emulsions were simulated by measuring the rate of reaction of peroxyl radicals generated in the aqueous phase with the encapsulated radical sensitive dye in the lipid core of the emulsions. The results of peroxyl radical permeation were compared to the stability of encapsulated retinol (model bioactive) in emulsions. To evaluate the role of layer-by-layer coatings in influencing oxidative barrier properties, radical permeation rates and retinol stability were evaluated in emulsion formulations of SDS emulsion and SDS emulsion with one or two layers of polymers (ϵ-polylysine and dextran sulfate) coated at the interface. To localize antioxidant molecules to the interface, gallic acid (GA) was chemically conjugated with ϵ-polylysine and subsequently deposited on SDS emulsion based on electrostatic interactions. Emulsion formulations with localized GA molecules at the interface were compared with SDS emulsion with GA molecules in the bulk aqueous phase. The results of this study demonstrate the advantage of localization of antioxidant at the interface and the limited impact of short chain polymer coatings at the interface of emulsions in reducing permeation of radicals and oxidation of a model encapsulated bioactive in oil-in-water emulsions. Copyright © 2015 Elsevier B.V. All rights reserved.

ProTec Tear-Offs: A Preliminary Assessment

International Nuclear Information System (INIS)

Peeler, D

2005-01-01

The Savannah River National Laboratory (SRNL) has conducted a series of ''scoping'' tests (referred to as Phase 1) to assess the potential use of a Mylar(reg s ign) tear-off system as a primary or secondary protective barrier to minimize acid etching (''frosting''), accidental scratching, and/or radiation damage for shielded cells windows. Conceptually, thin, multi-layered sheets of Mylar (referred to as a ''tear-off'' system) could be directly applied to the Lexan(reg s ign) sheet or glovebox/hood sash window to serve as a secondary (or primary) barrier. Upon degradation of visual clarity due to accidental scratching, spills/splatters, and/or radiation damage, the outer layer (or sheet) of Mylar could be removed ''refreshing'' or restoring the view. Due to the multi-layer aspect, the remaining Mylar layers would provide continued protection for the window from potential reoccurrences (which could be immediate or after some extended time period). Although the concept of using a tear-off system as a protective barrier was conceptually enticing, potential technical issues were identified and addressed as part of this Phase 1 feasibility study. These included resistance to: (1) acid(s) (concentrated (28.9 M) HF, concentrated (15.9M) HNO 3 , 6M HCl, and 0.6M H 3 BO 3 ), (2) base (a simulated sludge with pH of 12.9), (3) gamma radiation (cumulative dose of ∼200,000 rad), and (4) scratch resistance (simulating accidental scratching with the manipulators). Not only can these four factors play a significant role in determining the visual clarity of the integrated system, they can also contribute to the mechanical integrity issues which could dictate the ability to remove the outer layer when visual clarity has degraded. The results of the Phase 1 study clearly indicate that the Mylar tear-off concept (as a primary or secondary protective barrier) is a potential technical solution to prevent or retard excessive damage that would result from acid etching, base damage (as a

Effect of non-local equilibrium on minimal thermal resistance porous layered systems

International Nuclear Information System (INIS)

Leblond, Genevieve; Gosselin, Louis

2008-01-01

In this paper, the cooling of a heat-generating surface by a stacking of porous media (e.g., metallic foam) through which fluid flows parallel to the surface is considered. A two-temperature model is proposed to account for non-local thermal equilibrium (non-LTE). A scale analysis is performed to determine temperatures profiles in the boundary layer regime. The hot spot temperature is minimized with respect to the three design variables of each layer: porosity, pore diameter, and material. Global cost and mass are constrained. The optimization is performed with a hybrid genetic algorithm (GA) including local search to enhance convergence and repeatability. Results demonstrate that the optimized stacks do not operate in LTE. Therefore, we show that assuming LTE might result in underestimation of the hot spot temperature, and into different final designs as well

Achievement of normally-off AlGaN/GaN high-electron mobility transistor with p-NiO{sub x} capping layer by sputtering and post-annealing

Energy Technology Data Exchange (ETDEWEB)

Huang, Shyh-Jer [Department of Electrical Engineering, Institute of Microelectronics and Advanced Optoelectronic Technology Center, National Cheng Kung University, Tainan, Taiwan (China); Chou, Cheng-Wei, E-mail: j2222222229@gmail.com [Department of Electrical Engineering, Institute of Microelectronics and Advanced Optoelectronic Technology Center, National Cheng Kung University, Tainan, Taiwan (China); Su, Yan-Kuin, E-mail: yksu@mail.ncku.edu.tw [Department of Electrical Engineering, Institute of Microelectronics and Advanced Optoelectronic Technology Center, National Cheng Kung University, Tainan, Taiwan (China); Lin, Jyun-Hao; Yu, Hsin-Chieh; Chen, De-Long [Department of Electrical Engineering, Institute of Microelectronics and Advanced Optoelectronic Technology Center, National Cheng Kung University, Tainan, Taiwan (China); Ruan, Jian-Long [National Chung-Shan Institute of Science and Technology, Taoyuan, Taiwan (China)

2017-04-15

Highlights: • A technique to fabricate normally off GaN-based high-electron mobility transistor (HEMT) by sputtering and post-annealing p-NiO{sub x} capping layer. • The V{sub th} shifts from −3 V in the conventional transistor to 0.33 V, and on/off current ratio became 10{sup 7}. • The reverse gate leakage current is 10{sup −9} A/mm, and the off-state drain-leakage current is 10{sup −8} A/mm. • The V{sub th} hysteresis is extremely small at about 33 mV. - Abstract: In this paper, we present a technique to fabricate normally off GaN-based high-electron mobility transistor (HEMT) by sputtering and post-annealing p-NiO{sub x} capping layer. The p-NiO{sub x} layer is produced by sputtering at room temperature and post-annealing at 500 °C for 30 min in pure O{sub 2} environment to achieve high hole concentration. The V{sub th} shifts from −3 V in the conventional transistor to 0.33 V, and on/off current ratio became 10{sup 7}. The forward and reverse gate breakdown increase from 3.5 V and −78 V to 10 V and −198 V, respectively. The reverse gate leakage current is 10{sup −9} A/mm, and the off-state drain-leakage current is 10{sup −8} A/mm. The V{sub th} hysteresis is extremely small at about 33 mV. We also investigate the mechanism that increases hole concentration of p-NiO{sub x} after annealing in oxygen environment resulted from the change of Ni{sup 2+} to Ni{sup 3+} and the surge of (111)-orientation.

Accurate Local-Ancestry Inference in Exome-Sequenced Admixed Individuals via Off-Target Sequence Reads

Science.gov (United States)

Hu, Youna; Willer, Cristen; Zhan, Xiaowei; Kang, Hyun Min; Abecasis, Gonçalo R.

2013-01-01

Estimates of the ancestry of specific chromosomal regions in admixed individuals are useful for studies of human evolutionary history and for genetic association studies. Previously, this ancestry inference relied on high-quality genotypes from genome-wide association study (GWAS) arrays. These high-quality genotypes are not always available when samples are exome sequenced, and exome sequencing is the strategy of choice for many ongoing genetic studies. Here we show that off-target reads generated during exome-sequencing experiments can be combined with on-target reads to accurately estimate the ancestry of each chromosomal segment in an admixed individual. To reconstruct local ancestry, our method SEQMIX models aligned bases directly instead of relying on hard genotype calls. We evaluate the accuracy of our method through simulations and analysis of samples sequenced by the 1000 Genomes Project and the NHLBI Grand Opportunity Exome Sequencing Project. In African Americans, we show that local-ancestry estimates derived by our method are very similar to those derived with Illumina’s Omni 2.5M genotyping array and much improved in relation to estimates that use only exome genotypes and ignore off-target sequencing reads. Software implementing this method, SEQMIX, can be applied to analysis of human population history or used for genetic association studies in admixed individuals. PMID:24210252

Determination of localized visibility in off-axis electron holography

International Nuclear Information System (INIS)

McLeod, Robert A.; Kupsta, Martin; Malac, Marek

2014-01-01

Off-axis electron holography is a wavefront-split interference method for the transmission electron microscope that allows the phase shift and amplitude of the electron wavefront to be separated and quantitatively measured. An additional, third component of the holographic signal is the coherence of the electron wavefront. Historically, wavefront coherence has been evaluated by measurement of the holographic fringe visibility (or contrast) based on the minimum and maximum intensity values. We present a method based on statistical moments is presented that allows allow the visibility to be measured in a deterministic and reproducible fashion suitable for quantitative analysis. We also present an algorithm, based on the Fourier-ratio method, which allows the visibility to be resolved in two-dimensions, which we term the local visibility. The local visibility may be used to evaluate the loss of coherence due to electron scattering within a specimen, or as an aid in image analysis and segmentation. The relationship between amplitude and visibility may be used to evaluate the composition and mass thickness of a specimen by means of a 2-D histogram. Results for a selection of elements (C, Al, Si, Ti, Cr, Cu, Ge, and Au) are provided. All presented visibility metrics are biased at low-dose conditions by the presence of shot-noise, for which we provide methods for empirical normalization to achieve linear response. - Highlights: • Report on a new statistical metric to determine holographic fringe visibility. • Adds new signal to electron holography: measure of electron coherence loss in 2-D. • Provide algorithm to calculate 2-D local visibility map. • Show that amplitude and visibility may be used for compositional analysis and segmentation. • Corrected for data bias such as shot noise

In-situ potential mapping of space charge layer in GaN nanowires under electrical field by off-axis electron holography

Directory of Open Access Journals (Sweden)

Xiao Chen

2016-04-01

Full Text Available In situ potential mapping of space charge (SC layer in a single GaN nanowire (NW contacted to the Au metal electrode has been conducted using off-axis electron holography in order to study the space distribution of SC layer under electric biases. Based on the phase image reconstructed from the complex hologram the electrostatic potential at the SC layer was clearly revealed; the SC width was estimated to be about 76 nm under zero bias condition. In order to study dynamic interrelation between the SC layer and bias conditions, the variation of the electrostatic potential due to change of the SC widths respond to the different bias conditions have also been examined. The measured SC layers are found to vary between 68 nm and 91 nm, which correspond to the saturated SC layers at the GaN-Au contact under the forward and reverse bias conditions, respectively. By plotting the square widths of the SC layer against the applied voltages, donor density of GaN NWs was derived to be about 4.3*106 cm−3. Our experiments demonstrate that in-situ electron holography under electric field can be a useful method to investigate SC layers and donor density in single NW and other heterostructures.

Towards identifying the mechanisms underlying field-aligned edge-loss of HHFW power on NSTX

International Nuclear Information System (INIS)

Perkins, R. J.; Bell, R. E.; Bertelli, N.; Diallo, A.; Gerhardt, S.; Hosea, J. C.; Jaworski, M. A.; LeBlanc, B. P.; Kramer, G. J.; Maingi, R.; Phillips, C. K.; Podestà, M.; Roquemore, L.; Scotti, F.; Taylor, G.; Wilson, J. R.; Ahn, J-W.; Gray, T. K.; Green, D. L.; McLean, A.

2014-01-01

Fast-wave heating will be a major heating scheme on ITER, as it can heat ions directly and is relatively unaffected by the large machine size unlike neutral beams. However, fast-wave interactions with the plasma edge can lead to deleterious effects such as, in the case of the high-harmonic fast-wave (HHFW) system on NSTX, large losses of fast-wave power in the scrape off layer (SOL) under certain conditions. In such scenarios, a large fraction of the lost HHFW power is deposited on the upper and lower divertors in bright spiral shapes. The responsible mechanism(s) has not yet been identified but may include fast-wave propagation in the scrape off layer, parametric decay instability, and RF currents driven by the antenna reactive fields. Understanding and mitigating these losses is important not only for improving the heating and current-drive on NSTX-Upgrade but also for understanding fast-wave propagation across the SOL in any fast-wave system. This talk summarizes experimental results demonstrating that the flow of lost HHFW power to the divertor regions largely follows the open SOL magnetic field lines. This lost power flux is relatively large close to both the antenna and the last closed flux surface with a reduced level in between, so the loss mechanism cannot be localized to the antenna. At the same time, significant losses also occur along field lines connected to the inboard edge of the bottom antenna plate. The power lost within the spirals is roughly estimated, showing that these field-aligned losses to the divertor are significant but may not account for the total HHFW loss. To elucidate the role of the onset layer for perpendicular fast-wave propagation with regards to fast-wave propagation in the SOL, a cylindrical cold-plasma model is being developed. This model, in addition to advanced RF codes such as TORIC and AORSA, is aimed at identifying the underlying mechanism(s) behind these SOL losses, to minimize their effects in NSTX-U, and to predict

Towards identifying the mechanisms underlying field-aligned edge-loss of HHFW power on NSTX

Energy Technology Data Exchange (ETDEWEB)

Perkins, R. J.; Bell, R. E.; Bertelli, N.; Diallo, A.; Gerhardt, S.; Hosea, J. C.; Jaworski, M. A.; LeBlanc, B. P.; Kramer, G. J.; Maingi, R.; Phillips, C. K.; Podestà, M.; Roquemore, L.; Scotti, F.; Taylor, G.; Wilson, J. R. [Princeton Plasma Physics Laboratory, Princeton, NJ (United States); Ahn, J-W.; Gray, T. K.; Green, D. L.; McLean, A. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); and others

2014-02-12

Fast-wave heating will be a major heating scheme on ITER, as it can heat ions directly and is relatively unaffected by the large machine size unlike neutral beams. However, fast-wave interactions with the plasma edge can lead to deleterious effects such as, in the case of the high-harmonic fast-wave (HHFW) system on NSTX, large losses of fast-wave power in the scrape off layer (SOL) under certain conditions. In such scenarios, a large fraction of the lost HHFW power is deposited on the upper and lower divertors in bright spiral shapes. The responsible mechanism(s) has not yet been identified but may include fast-wave propagation in the scrape off layer, parametric decay instability, and RF currents driven by the antenna reactive fields. Understanding and mitigating these losses is important not only for improving the heating and current-drive on NSTX-Upgrade but also for understanding fast-wave propagation across the SOL in any fast-wave system. This talk summarizes experimental results demonstrating that the flow of lost HHFW power to the divertor regions largely follows the open SOL magnetic field lines. This lost power flux is relatively large close to both the antenna and the last closed flux surface with a reduced level in between, so the loss mechanism cannot be localized to the antenna. At the same time, significant losses also occur along field lines connected to the inboard edge of the bottom antenna plate. The power lost within the spirals is roughly estimated, showing that these field-aligned losses to the divertor are significant but may not account for the total HHFW loss. To elucidate the role of the onset layer for perpendicular fast-wave propagation with regards to fast-wave propagation in the SOL, a cylindrical cold-plasma model is being developed. This model, in addition to advanced RF codes such as TORIC and AORSA, is aimed at identifying the underlying mechanism(s) behind these SOL losses, to minimize their effects in NSTX-U, and to predict

Broadband magnetic and density fluctuations in the TCA tokamak

International Nuclear Information System (INIS)

Hollenstein, Ch.; Keller, R.; Pochelon, A.; Ryter, F.; Sawley, M.L.; Simm, W.; Weisen, H.

1987-01-01

The results of comparative studies of broadband magnetic and density fluctuations during ohmic discharges in the TCA tokamak are described. Long coherence lengths are observed in poloidal and toroidal directions between magnetic probes in the scrape-off layer. A phase contrast diagnostic provides a newly accessible range of density fluctuations in the bulk plasma with very long wavelengths. Langmuir probes provide similar measurements in the scrape-off layer. Statistical dispersion relations for both density and magnetic fluctuations are deduced and are shown to be substantially different. Low mean poloidal wavenumbers (m ∼ 2 at 100 kHz) are obtained for the magnetic fluctuations, in contrast to the much higher values measured for density fluctuations. The difference between magnetic and density fluctuations is also reflected in different scalings with plasma parameters and with electron confinement time. The helicity of the coherent magnetic structures is analyzed to show that interior regions of the plasma, such as the q = 2 region contribute to the magnetic activity at the edge. This explains why the magnetic fluctuations measured at the edge are likely to reflect the confinement properties of the bulk plasma. The results of detailed probe rotation experiments and coherence measurements give indications of the physical nature and origin of magnetic fluctuations

Numerical investigation of edge plasma phenomena in an enhanced D-alpha discharge at Alcator C-Mod: Parallel heat flux and quasi-coherent edge oscillations

International Nuclear Information System (INIS)

Russell, D. A.; D’Ippolito, D. A.; Myra, J. R.; LaBombard, B.; Terry, J. L.; Zweben, S. J.

2012-01-01

Reduced-model scrape-off layer turbulence (SOLT) simulations of an enhanced D-alpha (EDA) H-mode shot observed in the Alcator C-Mod tokamak were conducted to compare with observed variations in the scrape-off-layer (SOL) width of the parallel heat flux profile. In particular, the role of the competition between sheath- and conduction-limited parallel heat fluxes in determining that width was studied for the turbulent SOL plasma that emerged from the simulations. The SOL width decreases with increasing input power and with increasing separatrix temperature in both the experiment and the simulation, consistent with the strong temperature dependence of the parallel heat flux in balance with the perpendicular transport by turbulence and blobs. The particularly strong temperature dependence observed in the case analyzed is attributed to the fact that these simulations produce SOL plasmas which are in the conduction-limited regime for the parallel heat flux. A persistent quasi-coherent (QC) mode dominates the SOLT simulations and bears considerable resemblance to the QC mode observed in C-Mod EDA operation. The SOLT QC mode consists of nonlinearly saturated wave-fronts located just inside the separatrix that are convected poloidally by the mean flow, continuously transporting particles and energy and intermittently emitting blobs into the SOL.

Global transport and localized layering of metallic ions in the upper atmospherer

Directory of Open Access Journals (Sweden)

L. N. Carter

1999-02-01

Full Text Available A numerical model has been developed which is capable of simulating all phases of the life cycle of metallic ions, and results are described and interpreted herein for the typical case of Fe+ ions. This cycle begins with the initial deposition of metallics through meteor ablation and sputtering, followed by conversion of neutral Fe atoms to ions through photoionization and charge exchange with ambient ions. Global transport arising from daytime electric fields and poleward/ downward di.usion along geomagnetic field lines, localized transport and layer formation through de- scending convergent nulls in the thermospheric wind field, and finally annihilation by chemical neutralization and compound formation are treated. The model thus sheds new light on the interdependencies of the physical and chemical processes a.ecting atmospheric metallics. Model output analysis confirms the dominant role of both global and local transport to the ion's life cycle, showing that upward forcing from the equatorial electric field is critical to global movement, and that diurnal and semidiurnal tidal winds are responsible for the forma- tion of dense ion layers in the 90±250 km height region. It is demonstrated that the assumed combination of sources, chemical sinks, and transport mechanisms actually produces F-region densities and E-region layer densities similar to those observed. The model also shows that zonal and meridional winds and electric fields each play distinct roles in local transport, whereas the ion distribution is relatively insensitive to reasonable variations in meteoric deposition and chemical reaction rates.Key words. Ionosphere (ion chemistry and composition; ionosphere-atmosphere interactions.

Atom-scale depth localization of biologically important chemical elements in molecular layers.

Science.gov (United States)

Schneck, Emanuel; Scoppola, Ernesto; Drnec, Jakub; Mocuta, Cristian; Felici, Roberto; Novikov, Dmitri; Fragneto, Giovanna; Daillant, Jean

2016-08-23

In nature, biomolecules are often organized as functional thin layers in interfacial architectures, the most prominent examples being biological membranes. Biomolecular layers play also important roles in context with biotechnological surfaces, for instance, when they are the result of adsorption processes. For the understanding of many biological or biotechnologically relevant phenomena, detailed structural insight into the involved biomolecular layers is required. Here, we use standing-wave X-ray fluorescence (SWXF) to localize chemical elements in solid-supported lipid and protein layers with near-Ångstrom precision. The technique complements traditional specular reflectometry experiments that merely yield the layers' global density profiles. While earlier work mostly focused on relatively heavy elements, typically metal ions, we show that it is also possible to determine the position of the comparatively light elements S and P, which are found in the most abundant classes of biomolecules and are therefore particularly important. With that, we overcome the need of artificial heavy atom labels, the main obstacle to a broader application of high-resolution SWXF in the fields of biology and soft matter. This work may thus constitute the basis for the label-free, element-specific structural investigation of complex biomolecular layers and biological surfaces.

An iterative procedure for estimating areally averaged heat flux using planetary boundary layer mixed layer height and locally measured heat flux

Energy Technology Data Exchange (ETDEWEB)

Coulter, R. L.; Gao, W.; Lesht, B. M.

2000-04-04

Measurements at the central facility of the Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) are intended to verify, improve, and develop parameterizations in radiative flux models that are subsequently used in General Circulation Models (GCMs). The reliability of this approach depends upon the representativeness of the local measurements at the central facility for the site as a whole or on how these measurements can be interpreted so as to accurately represent increasingly large scales. The variation of surface energy budget terms over the SGP CART site is extremely large. Surface layer measurements of the sensible heat flux (H) often vary by a factor of 2 or more at the CART site (Coulter et al. 1996). The Planetary Boundary Layer (PBL) effectively integrates the local inputs across large scales; because the mixed layer height (h) is principally driven by H, it can, in principal, be used for estimates of surface heat flux over scales on the order of tens of kilometers. By combining measurements of h from radiosondes or radar wind profiles with a one-dimensional model of mixed layer height, they are investigating the ability of diagnosing large-scale heat fluxes. The authors have developed a procedure using the model described by Boers et al. (1984) to investigate the effect of changes in surface sensible heat flux on the mixed layer height. The objective of the study is to invert the sense of the model.

Edge turbulence imaging in the Alcator C-Mod tokamak

International Nuclear Information System (INIS)

Zweben, S.J.; Stotler, D.P.; Terry, J.L.; La Bombard, B.; Greenwald, M.; Muterspaugh, M.; Pitcher, C.S.; Hallatschek, K.; Maqueda, R.J.; Rogers, B.; Lowrance, J.L.; Mastrocola, V.J.; Renda, G.F.

2002-01-01

The two-dimensional (2D) radial vs poloidal structure of edge turbulence in the Alcator C-Mod tokamak [I. H. Hutchinson, R. Boivin, P. T. Bonoli et al., Nucl. Fusion 41, 1391 (2001)] was measured using fast cameras and compared with three-dimensional numerical simulations of edge plasma turbulence. The main diagnostic is gas puff imaging, in which the visible D α emission from a localized D 2 gas puff is viewed along a local magnetic field line. The observed D α fluctuations have a typical radial and poloidal scale of ≅1 cm, and often have strong local maxima ('blobs') in the scrape-off layer. The motion of this 2D structure motion has also been measured using an ultrafast framing camera with 12 frames taken at 250 000 frames/s. Numerical simulations produce turbulent structures with roughly similar spatial and temporal scales and transport levels as that observed in the experiment; however, some differences are also noted, perhaps requiring diagnostic improvement and/or additional physics in the numerical model

Measurement and modelling of suprathermal electron bursts generated in front of a lower hybrid antenna

Czech Academy of Sciences Publication Activity Database

Gunn, J. P.; Fuchs, Vladimír; Petržílka, Václav; Ekedahl, A.; Fedorczak, N.; Goniche, M.; Hillairet, J.

2016-01-01

Roč. 56, č. 3 (2016), č. článku 036004. ISSN 0029-5515 R&D Projects: GA MŠk(CZ) LM2011021 Institutional support: RVO:61389021 Keywords : lower hybrid * scrape off layer * SOL turbulence * Landau damping * suprathermal electrons Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 3.307, year: 2016 http://iopscience.iop.org/article/10.1088/0029-5515/56/3/036004

Direct Fusion Drive for a Human Mars Orbital Mission

Energy Technology Data Exchange (ETDEWEB)

Paluszek, Michael [Princeton Satellite Systems; Pajer, Gary [Princeton Satellite Systems; Razin, Yosef [Princeton Satellite Systems; Slonaker, James [Princeton Satellite Systems; Cohen, Samuel [PPPL; Feder, Russ [PPPL; Griffin, Kevin [Princeton University; Walsh, Matthew [Princeton University

2014-08-01

The Direct Fusion Drive (DFD) is a nuclear fusion engine that produces both thrust and electric power. It employs a field reversed configuration with an odd-parity rotating magnetic field heating system to heat the plasma to fusion temperatures. The engine uses deuterium and helium-3 as fuel and additional deuterium that is heated in the scrape-off layer for thrust augmentation. In this way variable exhaust velocity and thrust is obtained.

Understanding SOL plasma turbulence by interchange motions

Czech Academy of Sciences Publication Activity Database

Horáček, Jan; Pitts, R. A.; Nielsen, A.H.; Garcia, O.E.

2007-01-01

Roč. 52, č. 16 (2007), s. 192-193 ISSN 0003-0503. [Annual meeting of the division of plasma physics/49th./. Orlando , 12.11.2007-16.11.2007] Grant - others:-(XE) European Training fellowships and Grants (Euratom), EDGETURB Institutional research plan: CEZ:AV0Z20430508 Keywords : tokamak * plasma * scrape-off layer * turbulence * interchange instability Subject RIV: BL - Plasma and Gas Discharge Physics http://meetings.aps.org/Meeting/DPP07/Event/70125

Spectroscopic investigation of ELM phenomena in the ASDEX-Upgrade divertor with high time resolution

International Nuclear Information System (INIS)

Field, A.R.; Buechl, K.; Fuchs, C.J.; Fussmann, G.; Herrmann, A.; Lieder, G.; Napiontek, B.; Radtke, R.; Wenzel, U.; Zohm, H.

1993-01-01

Improved tokamak H-mode confinement is associated with the formation of an insulating zone just within the separatrix. At a critical pressure gradient a sudden burst of MHD activity (an ELM) degrades edge confinement, releasing particles and energy into the scrape-off layer (SOL) which is subsequently transported to the divertor. Here, these phenomena are studied using spectroscopic diagnostics and target plate thermography of high spatial and temporal resolution. (author) 3 refs., 6 figs

Spectroscopic investigation of ELM phenomena in the ASDEX-Upgrade divertor with high time resolution

Energy Technology Data Exchange (ETDEWEB)

Field, A R; Buechl, K; Fuchs, C J; Fussmann, G; Herrmann, A; Lieder, G; Napiontek, B; Radtke, R; Wenzel, U; Zohm, H [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany)

1994-12-31

Improved tokamak H-mode confinement is associated with the formation of an insulating zone just within the separatrix. At a critical pressure gradient a sudden burst of MHD activity (an ELM) degrades edge confinement, releasing particles and energy into the scrape-off layer (SOL) which is subsequently transported to the divertor. Here, these phenomena are studied using spectroscopic diagnostics and target plate thermography of high spatial and temporal resolution. (author) 3 refs., 6 figs.

Excitation of terahertz modes localized on a layered superconductor: Anomalous dispersion and resonant transmission

Science.gov (United States)

Apostolov, S. S.; Makarov, N. M.; Yampol'skii, V. A.

2018-01-01

We study theoretically the optic transmission through a slab of layered superconductor separated from two dielectric leads by spatial gaps. Based on the transfer matrix formalism along with the Josephson plasma electrodynamic approach, we derive analytic expressions for the transmittance and identify the conditions for the perfect transmission. The special interest of the study is focused on the resonant transmission, which occurs when the wave does not propagate in the spatial gaps. Far from the resonance, the transmittance is exponentially small due to the total internal reflection from the lead-gap interface. However, the excitation of electromagnetic modes localized on the layered superconductor gives rise to a remarkable resonant enhancement of the transmission. Moreover, this phenomenon is significantly modified for the layered superconductors in comparison with usual dielectrics or conductors. The dispersion curves for the modes localized on the layered superconductor are proved to be nonmonotonic, thus resulting in the specific dependence of the transmittance T on the incidence angle θ . In particular, we predict the onset of two resonant peaks in the T (θ ) dependence and their subsequent merge into the broadened single peak with increasing of the wave frequency. Our analytical results are demonstrated by numerical data.

Autonomous tracked robots in planar off-road conditions modelling, localization, and motion control

CERN Document Server

González, Ramón; Guzmán, José Luis

2014-01-01

This monograph is framed within the context of off-road mobile robotics. In particular, it discusses issues related to modelling, localization, and motion control of tracked mobile robots working in planar slippery conditions. Tracked locomotion constitutes a well-known solution for mobile platforms operating over diverse challenging terrains, for that reason, tracked robotics constitutes an important research field with many applications (e.g. agriculture, mining, search and rescue operations, military activities). The specific topics of this monograph are: historical perspective of tracked vehicles and tracked robots; trajectory-tracking model taking into account slip effect; visual-odometry-based localization strategies; and advanced slip-compensation motion controllers ensuring efficient real-time execution. Physical experiments with a real tracked robot are presented showing the better performance of the suggested novel approaches to known techniques.   Keywords: longitudinal slip, visual odometry, slip...

Studying the Dynamics of Breakdown of Thin Horizontal Liquid Layers with Local Heating

Directory of Open Access Journals (Sweden)

Spesivtsev Serafim

2016-01-01

Full Text Available Experimental study of liquid layers breakdown when heated locally from the substrate side was made. Water and ethanol were used as working liquids with a layer thickness of 300 μm. Basic steps of the breakdown process were found and mean velocities of the dry spot formation were determined; the values are 0.06 mm/sec for ethanol and 5.15 mm/sec for water. The formation of residual layer over the hot-spot before the breakdown has been found for both liquids. The creation of a droplet cluster near the heating region is observed when using water as a working fluid. It was shown that evaporation is one of the general factors influencing the process of layer breakdown and dry spot formation as well as thermocapillary effect.

Intermittency in the Scrape-off Layer of the National Spherical Torus Experiment During H-mode Confinement

International Nuclear Information System (INIS)

Maqueda, R.J.; Stotler, D.P.; Zweben, S.J.

2010-01-01

A gas puff imaging diagnostic is used in the National Spherical Tokamak Experiment (M. Ono, et al., Nucl. Fusion 40, 557 (2000)) to study the edge turbulence and intermittency present during H-mode discharges. In the case of low power Ohmic H-modes the suppression of turbulence/blobs is maintained through the duration of the (short lived) H-modes. Similar quiescent edges are seen during the early stages of H-modes created with the use of neutral beam injection. Nevertheless, as time progresses following the L-H transition, turbulence and blobs reappear although at a lower level than that typically seen during L-mode confinement. It is also seen that the time-averaged SOL emission profile broadens, as the power loss across the separatrix increases. These broad profiles are characterized by a large level of fluctuations and intermittent events.

Characterization of type-I ELM induced filaments in the far scrape-off layer of ASDEX upgrade

Energy Technology Data Exchange (ETDEWEB)

Schmid, Andreas

2008-03-18

This thesis focuses on the characterization of filaments and their propagation in the ASDEX Upgrade tokamak. The aim is to provide experimental measurements for understanding the filament formation process and their temporal evolution, and to provide a comprehensive database for an extrapolation to future fusion devices. For this purpose, a new magnetically driven probe for filament measurements has been developed and installed in ASDEX Upgrade. The probe carries several Langmuir probes and a magnetic coil in between. The Langmuir probes allow for measurements of the radial and poloidal/toroidal propagation of filaments as well as for measurements of filament size, density, and their radial (or temporal) evolution. The magnetic coil on the filament probe allows for measurements of currents in the filaments. A set of 7 coils, measuring 3 field components at different positions along the filament, has been used to measure the magnetic signature during an ELM. The aim was, on the one hand, to study which role filaments play for the magnetic structure, and on the other hand if the parallel currents predicted by the sheath damped model could be verified. Filament temperatures have been derived and the corresponding heat transport mechanisms have been studied. (orig.)

Divertor asymmetry and scrape-off layer flow in various divertor configurations in Experimental Advanced Superconducting Tokamak

DEFF Research Database (Denmark)

Liu, S. C.; Guo, H. Y.; Xu, Guandong

2012-01-01

moving Mach probe at the outer midplane, which shows similar magnitude to the Pfirsch-Schluter flow. Its contribution to the poloidal particle flux is also assessed and comparison is made with that from the poloidal E x B drift. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4707396]...

Plasma profiles and flows in the high-field side scrape-off layer in Alcator C-Mod

Energy Technology Data Exchange (ETDEWEB)

Smick, N. [MIT Plasma Science and Fusion Center, NW17-170, 175 Albany St., Cambridge, MA 02139 (United States)]. E-mail: nsmick@mit.edu; LaBombard, B. [MIT Plasma Science and Fusion Center, NW17-170, 175 Albany St., Cambridge, MA 02139 (United States); Pitcher, C.S. [132 Bowood Ave., Toronto, M4N1Y5 (Canada)

2005-03-01

A novel, magnetically-driven swing probe was recently installed near the midplane on the high-field side SOL in Alcator C-Mod. The probe collects plasma from co- and counter-current directions during its respective 0-90 deg and 90-180 deg of motion, thus providing profiles of density, electron temperature and plasma flow parallel to magnetic field lines (Mach number, M{sub parallel}) up to the separatrix. Results are reported from discharges with different magnetic topologies: lower single-null, upper single-null, and double-null. In single-null, a strong parallel flow (vertical bar M{sub parallel} vertical bar {approx} 1) is detected, which is always directed from the low- to high-field SOL. In double-null discharges, e-folding lengths in the high-field SOL are a factor of {approx}4 shorter than the low-field SOL. Thus, plasma appears to 'fill-in' the high-field SOL in single-null plasmas, not by cross-field transport but by parallel flow from the low-field SOL - a picture consistent with a very strong ballooning-like component to the cross-field transport.

Loss mechanism of the superthermal electrons across the separatrix into the scrape-off layer in DIVA

International Nuclear Information System (INIS)

Yamamoto, Shin; Sengoku, Seio; Kimura, Haruyuki; Shimomura, Yasuo; Maeda, Hikosuke

1977-10-01

Behavior of superthermal electrons is investigated by using X-ray measurement and electrostatic energy analyser. Superthermal electrons are divided into two groups; i.e. high energy electrons (10 keV - 100 keV) and epithermal electrons (150 eV - 500 eV). Loss flux of the epithermal electrons is obtained and their loss is shown to be explained by destruction of magnetic surfaces near the separatrix due to non-axisymmetric perturbations. Two-dimensional path of high energy electrons is obtained and the effects of non-axisymmetric perturbations on the drift surface are described. (auth.)

Characterization of type-I ELM induced filaments in the far scrape-off layer of ASDEX upgrade

International Nuclear Information System (INIS)

Schmid, Andreas

2008-01-01

This thesis focuses on the characterization of filaments and their propagation in the ASDEX Upgrade tokamak. The aim is to provide experimental measurements for understanding the filament formation process and their temporal evolution, and to provide a comprehensive database for an extrapolation to future fusion devices. For this purpose, a new magnetically driven probe for filament measurements has been developed and installed in ASDEX Upgrade. The probe carries several Langmuir probes and a magnetic coil in between. The Langmuir probes allow for measurements of the radial and poloidal/toroidal propagation of filaments as well as for measurements of filament size, density, and their radial (or temporal) evolution. The magnetic coil on the filament probe allows for measurements of currents in the filaments. A set of 7 coils, measuring 3 field components at different positions along the filament, has been used to measure the magnetic signature during an ELM. The aim was, on the one hand, to study which role filaments play for the magnetic structure, and on the other hand if the parallel currents predicted by the sheath damped model could be verified. Filament temperatures have been derived and the corresponding heat transport mechanisms have been studied. (orig.)

Investigation of split-off dimers on the Si(001)2x1 surface

International Nuclear Information System (INIS)

Schofield, S.R.; O'Brien, J.L.; Curson, N.J.; Simmons, M.Y.; Clark, R.G.

2002-01-01

Full text: A detailed knowledge of the nature of crystalline defects on the Si(001)2x1 surface is becoming increasingly important as more research effort is dedicated to producing atomic-scale electronic devices. Here we present high-resolution scanning tunnelling microscopy (STM) images and ab initio pseudopotential calculations of an unusual defect of the silicon (001) surface called the split-off dimer. In high-resolution filled-state images, split-off dimers appear as a pair of protrusions, in contrast to the surrounding surface dimers that appear as 'bean-shaped' protrusions. We show that π-bonding does not exist between the atoms of the split-off dimer, but instead, the dimer atoms form π-bonds with two second layer atoms as part of a tetramer bonding arrangement. We discuss the strain associated with split-off dimer defects and describe how this strain significantly affects the bonding arrangements and local density of states around these defects

Quantitative measurement of mean inner potential and specimen thickness from high-resolution off-axis electron holograms of ultra-thin layered WSe{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Winkler, Florian, E-mail: f.winkler@fz-juelich.de [Ernst Ruska-Centre for Microscopy and Spectroscopy with Electrons (ER-C), Forschungszentrum Jülich, D-52425 Jülich (Germany); Peter Grünberg Institute 5 (PGI-5), Forschungszentrum Jülich, D-52425 Jülich (Germany); Tavabi, Amir H. [Ernst Ruska-Centre for Microscopy and Spectroscopy with Electrons (ER-C), Forschungszentrum Jülich, D-52425 Jülich (Germany); Peter Grünberg Institute 5 (PGI-5), Forschungszentrum Jülich, D-52425 Jülich (Germany); Barthel, Juri [Ernst Ruska-Centre for Microscopy and Spectroscopy with Electrons (ER-C), Forschungszentrum Jülich, D-52425 Jülich (Germany); Gemeinschaftslabor für Elektronenmikroskopie (GFE), RWTH Aachen University, D-52074 Aachen (Germany); Duchamp, Martial [Ernst Ruska-Centre for Microscopy and Spectroscopy with Electrons (ER-C), Forschungszentrum Jülich, D-52425 Jülich (Germany); Peter Grünberg Institute 5 (PGI-5), Forschungszentrum Jülich, D-52425 Jülich (Germany); Yucelen, Emrah [FEI Company, Achtseweg Noord 5, Eindhoven 5600 KA (Netherlands); Borghardt, Sven; Kardynal, Beata E. [Peter Grünberg Institute 9 (PGI-9), Forschungszentrum Jülich, D-52425 Jülich (Germany); and others

2017-07-15

The phase and amplitude of the electron wavefunction that has passed through ultra-thin flakes of WSe{sub 2} is measured from high-resolution off-axis electron holograms. Both the experimental measurements and corresponding computer simulations are used to show that, as a result of dynamical diffraction, the spatially averaged phase does not increase linearly with specimen thickness close to an [001] zone axis orientation even when the specimen has a thickness of only a few layers. It is then not possible to infer the local specimen thickness of the WSe{sub 2} from either the phase or the amplitude alone. Instead, we show that the combined analysis of phase and amplitude from experimental measurements and simulations allows an accurate determination of the local specimen thickness. The relationship between phase and projected potential is shown to be approximately linear for extremely thin specimens that are tilted by several degrees in certain directions from the [001] zone axis. A knowledge of the specimen thickness then allows the electrostatic potential to be determined from the measured phase. By using this combined approach, we determine a value for the mean inner potential of WSe{sub 2} of 18.9±0.8 V, which is 12% lower than the value calculated from neutral atom scattering factors. - Highlights: • Quantitative analysis of high resolution electron holograms of WSe{sub 2}. • Local specimen thickness determination and estimation of tilt angle. • Mean inner potential evaluation of WSe2 avoiding dynamical diffraction.

Summary of experimental core turbulence characteristics in ohmic and electron cyclotron resonance heated discharges in T-10 tokamak plasmas

International Nuclear Information System (INIS)

Vershkov, V.A.; Shelukhin, D.A.; Soldatov, S.V.; Urazbaev, A.O.; Grashin, S.A.; Eliseev, L.G.; Melnikov, A.V.

2005-01-01

This report summarizes the results of experimental turbulence investigations carried out at T-10 for more than 10 years. The turbulence characteristics were investigated using correlation reflectometry, multipin Langmuir probe (MLP) and heavy ion beam probe diagnostics. The reflectometry capabilities were analysed using 2D full-wave simulations and verified by direct comparison using a MLP. The ohmic and electron cyclotron resonance heated discharges show the distinct transition from the core turbulence, having complex spectral structure, to the unstructured one in the scrape-off layer. The core turbulence includes 'broad band, quasi-coherent' features, arising due to the excitation of rational surfaces with high poloidal m-numbers, with a low frequency near zero and specific oscillations at 15-30 kHz. All experimentally measured properties of low frequency and high frequency quasi-coherent oscillations are in good agreement with predictions of linear theory for the ion temperature gradient/dissipative trapped electron mode instabilities. Significant local changes in the turbulence characteristics were observed at the edge velocity shear layer and in the core near q = 1 radius after switching off the electron cyclotron resonance heating (ECRH). The local decrease in the electron heat conductivity and decrease in the turbulence level could be evidence of the formation of an electron internal transport barrier. The dynamic behaviour of the core turbulence was also investigated for the case of fast edge cooling and the beginning phase of ECRH

Global transport and localized layering of metallic ions in the upper atmospherer

Directory of Open Access Journals (Sweden)

L. N. Carter

Full Text Available A numerical model has been developed which is capable of simulating all phases of the life cycle of metallic ions, and results are described and interpreted herein for the typical case of Fe+ ions. This cycle begins with the initial deposition of metallics through meteor ablation and sputtering, followed by conversion of neutral Fe atoms to ions through photoionization and charge exchange with ambient ions. Global transport arising from daytime electric fields and poleward/ downward di.usion along geomagnetic field lines, localized transport and layer formation through de- scending convergent nulls in the thermospheric wind field, and finally annihilation by chemical neutralization and compound formation are treated. The model thus sheds new light on the interdependencies of the physical and chemical processes a.ecting atmospheric metallics. Model output analysis confirms the dominant role of both global and local transport to the ion's life cycle, showing that upward forcing from the equatorial electric field is critical to global movement, and that diurnal and semidiurnal tidal winds are responsible for the forma- tion of dense ion layers in the 90±250 km height region. It is demonstrated that the assumed combination of sources, chemical sinks, and transport mechanisms actually produces F-region densities and E-region layer densities similar to those observed. The model also shows that zonal and meridional winds and electric fields each play distinct roles in local transport, whereas the ion distribution is relatively insensitive to reasonable variations in meteoric deposition and chemical reaction rates.

Key words. Ionosphere (ion chemistry and composition; ionosphere-atmosphere interactions.

Localized Retinal Nerve Fiber Layer Defects in Red-free Photographs Versus En Face Structural Optical Coherence Tomography Images.

Science.gov (United States)

Jung, Jae Hoon; Park, Ji-Hye; Yoo, Chungkwon; Kim, Yong Yeon

2018-03-01

The purpose of this article is to compare the locations of localized retinal nerve fiber layer (RNFL) defects in red-free fundus photographs and optical coherence tomography (OCT) en face images. We performed a retrospective, comparative study on 46 eyes from 46 glaucoma patients with localized RNFL defects observed in red-free fundus photographs. En face structural images were obtained in the superficial and whole retinal layers using OCT and were overlaid on the corresponding red-free fundus photographs. The proximal/distal angular locations and angular width of each RNFL defect in red-free photos (red-free defects) and in en face structural images (en face defects) were compared. In the superficial retinal layer, there were no significant differences between red-free and en face defects on the proximal/distal angular location and angular width. In the whole retinal layer, the degree of the distal angular location of the en face defects was significantly larger than that of the red-free defects (71.85±18.26 vs. 70.87±17.90 degrees, P=0.003). The correlations of clinical variables with the differences in angular parameters between red-free and en face defects were not significant in the superficial retinal layer. The average RNFL thickness was negatively correlated with the difference in the distal angular location in the whole retinal layer (Pearson correlation coefficient=-0.401, P=0.006). Localized RNFL defects detected in OCT en face structural images of the superficial retinal layer showed high topographic correlation with defects detected in red-free photographs. OCT en face structural images in the superficial layer may be an alternative to red-free fundus photography for the identification of localized RNFL defects in glaucomatous eyes.

Off-wall boundary conditions for turbulent flows obtained from buffer-layer minimal flow units

Science.gov (United States)

Garcia-Mayoral, Ricardo; Pierce, Brian; Wallace, James

2012-11-01

There is strong evidence that the transport processes in the buffer region of wall-bounded turbulence are common across various flow configurations, even in the embryonic turbulence in transition (Park et al., Phys. Fl. 24). We use this premise to develop off-wall boundary conditions for turbulent simulations. Boundary conditions are constructed from DNS databases using periodic minimal flow units and reduced order modeling. The DNS data was taken from a channel at Reτ = 400 and a zero-pressure gradient transitional boundary layer (Sayadi et al., submitted to J . FluidMech .) . Both types of boundary conditions were first tested on a DNS of the core of the channel flow with the aim of extending their application to LES and to spatially evolving flows. 2012 CTR Summer Program.

Whole scrapings of cassava root in diets for broilers from 1 to 21 days of age

Directory of Open Access Journals (Sweden)

Antônio Hosmylton Carvalho Ferreira

2014-09-01

Full Text Available The study was conducted to evaluate the effect of including whole cassava root scrapings (WCS in diets of broilers on performance and the metabolizability of dry matter, crude protein, and gross energy and on nitrogenous balance. Four hundred female and 100 male broilers from Ross strain were used in the performance and metabolism studies, respectively. In both studies, broilers were allotted in completely randomized block design with five treatments and four replicates. The experimental unit was represented for twenty birds per box for performance study and five birds per metabolic cage for metabolism study. The treatments consisted of diets containing 0, 5, 10, 15, and 20% WCS inclusion. Up to 5.1% WCS can be included in the diet of broilers from 1 to 21 without compromising feed conversion and productive efficiency index. Dry matter, crude protein, and gross energy metabolizability and the nitrogen balance of the diets are not influenced by the inclusion of whole cassava root scrapings up to 20% in diets of broilers from 1 to 21 days of age.

Quantitative measurement of mean inner potential and specimen thickness from high-resolution off-axis electron holograms of ultra-thin layered WSe2.

Science.gov (United States)

Winkler, Florian; Tavabi, Amir H; Barthel, Juri; Duchamp, Martial; Yucelen, Emrah; Borghardt, Sven; Kardynal, Beata E; Dunin-Borkowski, Rafal E

2017-07-01

The phase and amplitude of the electron wavefunction that has passed through ultra-thin flakes of WSe 2 is measured from high-resolution off-axis electron holograms. Both the experimental measurements and corresponding computer simulations are used to show that, as a result of dynamical diffraction, the spatially averaged phase does not increase linearly with specimen thickness close to an [001] zone axis orientation even when the specimen has a thickness of only a few layers. It is then not possible to infer the local specimen thickness of the WSe 2 from either the phase or the amplitude alone. Instead, we show that the combined analysis of phase and amplitude from experimental measurements and simulations allows an accurate determination of the local specimen thickness. The relationship between phase and projected potential is shown to be approximately linear for extremely thin specimens that are tilted by several degrees in certain directions from the [001] zone axis. A knowledge of the specimen thickness then allows the electrostatic potential to be determined from the measured phase. By using this combined approach, we determine a value for the mean inner potential of WSe 2 of 18.9±0.8V, which is 12% lower than the value calculated from neutral atom scattering factors. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Localized Corrosion Behavior of Type 304SS with a Silica Layer Under Atmospheric Corrosion Environments

International Nuclear Information System (INIS)

E. Tada; G.S. Frankel

2006-01-01

The U.S. Department of Energy (DOE) has proposed a potential repository for spent nuclear fuel and high-level radioactive waste at the Yucca Mountain site in Nevada. [I] The temperature could be high on the waste packages, and it is possible that dripping water or humidity could interact with rock dust particulate to form a thin electrolyte layer with concentrated ionic species. Under these conditions, it is possible that highly corrosion-resistant alloys (CRAs) used as packages to dispose the nuclear waste could suffer localized corrosion. Therefore, to better understand long-term corrosion performance of CRAs in the repository, it is important to investigate localized corrosion under a simulated repository environment. We measured open circuit potential (OCP) and galvanic current (i g ) for silica-coated Type 304SS during drying of salt solutions under controlled RH environments to clarify the effect of silica layer as a dust layer simulant on localized corrosion under atmospheric environments. Type 304SS was used as a relatively susceptible model CRA instead of the much more corrosion resistant alloys, such as Alloy 22, that are being considered as, waste package materials

Is there an ideal REDD+ program? An analysis of policy trade-offs at the local level.

Science.gov (United States)

Dyer, George A; Matthews, Robin; Meyfroidt, Patrick

2012-01-01

We use economy-wide simulation methods to analyze the outcome of a simple REDD+ program in a mixed subsistence/commercial-agriculture economy. Alternative scenarios help trace REDD+'s causal chain, revealing how trade-offs between the program's public and private costs and benefits determine its effectiveness, efficiency and equity (the 3Es). Scenarios reveal a complex relationship between the 3Es not evident in more aggregate analyses. Setting aside land as a carbon sink always influences the productivity of agriculture and its supply of non-market goods and services; but the overall returns to land and labor-which ultimately determine the opportunity cost of enrollment, the price of carbon and the distribution of gains and losses-depend on local conditions. In the study area, market-oriented landowners could enroll 30% of local land into a cost-effective program, but local subsistence demands would raise their opportunity costs as REDD+ unfurls, increasing the marginal cost of carbon. A combination of rent and wage changes would create net costs for most private stakeholders, including program participants. Increasing carbon prices undermines the program's efficiency without solving its inequities; expanding the program reduces inefficiencies but increases private costs with only minor improvements in equity. A program that prevents job losses could be the best option, but its efficiency compared to direct compensation could depend on program scale. Overall, neither the cost nor the 3Es of alternative REDD+ programs can be assessed without accounting for local demand for subsistence goods and services. In the context of Mexico's tropical highlands, a moderate-sized REDD+ program could at best have no net impact on rural households. REDD+ mechanisms should avoid general formulas by giving local authorities the necessary flexibility to address the trade-offs involved. National programs themselves should remain flexible enough to adjust for spatially and temporally

Is there an ideal REDD+ program? An analysis of policy trade-offs at the local level.

Directory of Open Access Journals (Sweden)

George A Dyer

Full Text Available We use economy-wide simulation methods to analyze the outcome of a simple REDD+ program in a mixed subsistence/commercial-agriculture economy. Alternative scenarios help trace REDD+'s causal chain, revealing how trade-offs between the program's public and private costs and benefits determine its effectiveness, efficiency and equity (the 3Es. Scenarios reveal a complex relationship between the 3Es not evident in more aggregate analyses. Setting aside land as a carbon sink always influences the productivity of agriculture and its supply of non-market goods and services; but the overall returns to land and labor-which ultimately determine the opportunity cost of enrollment, the price of carbon and the distribution of gains and losses-depend on local conditions. In the study area, market-oriented landowners could enroll 30% of local land into a cost-effective program, but local subsistence demands would raise their opportunity costs as REDD+ unfurls, increasing the marginal cost of carbon. A combination of rent and wage changes would create net costs for most private stakeholders, including program participants. Increasing carbon prices undermines the program's efficiency without solving its inequities; expanding the program reduces inefficiencies but increases private costs with only minor improvements in equity. A program that prevents job losses could be the best option, but its efficiency compared to direct compensation could depend on program scale. Overall, neither the cost nor the 3Es of alternative REDD+ programs can be assessed without accounting for local demand for subsistence goods and services. In the context of Mexico's tropical highlands, a moderate-sized REDD+ program could at best have no net impact on rural households. REDD+ mechanisms should avoid general formulas by giving local authorities the necessary flexibility to address the trade-offs involved. National programs themselves should remain flexible enough to adjust for

Decontamination technology verification test on scraping surface soil on the highway roadside slopes using unmanned scraping machine

International Nuclear Information System (INIS)

Fujinaka, Hiroyuki; Kubota, Mitsuru; Shibuya, Susumu; Kasai, Yoshimitsu

2013-01-01

The restore the normal life in the contaminated area, reconstruction of the infrastructure is necessary and early decontamination of roads and roadside slopes of highway are required. Decontamination work of roadside slopes is conducted only by hand working so far, but on the high and steep roadside slopes it is desirable to carry out decontamination work by an unmanned scraping machine to reduce working hours and improve safety. In this verification test, decontamination work of the roadside slope of highway, of which area was 20m W x 15m L and divided into two sections, was implemented by the machine or by hand, and working hours and radiation exposure dose were measured. As the results of the test, working hours and radiation exposure dose by the machine were 49% and 63% respectively compared to those by hand. Based on the results, cost and radiation dose for decontamination work on larger slopes were evaluated. Cost by the machine is estimated to be less than that by hand where the area is over 4,000m 2 . It is confirmed that the decontamination work of roadside slopes by the machine can be done more quickly and safely in comparison with hand working. (author)

EXAFS determination of cation local order in layered perovskites

Energy Technology Data Exchange (ETDEWEB)

Montero C, M. E.; Fuentes M, L.; Duarte M, J. A.; Fuentes C, L. [Centro de Investigacion en Materiales Avanzados S. C., Miguel de Cervantes Saavedra 120, Complejo Industrial Chihuahua, 31109 Chihuahua (Mexico); Garcia G, M. [Instituto de Fisica, UNAM, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Mehta, A.; Webb, S. [Stanford Synchrotron Radiation Laboratory, CA (United States)

2008-02-15

EXAFS analysis of Bi{sub 6}Ti{sub 3}Fe{sub 2}O{sub 18} Aurivillius ceramic was performed to elucidate the local environment of Fe cations. Experiments were performed at Stanford Synchrotron Radiation Laboratory, at T = 10, 30, 50, 75, 100 and 298 K, in fluorescence regime. EXAFS spectra were processed using the ab initio multiple scattering program FEFF6. Distances among representative atomic pairs were refined. As a basic result, the previous hypothesis suggested by X-ray diffraction experiments, regarding a preference of iron atoms for the centered perovskite layer of the unit cell, was confirmed. (Author)

Local characteristics of the nocturnal boundary layer in response to external pressure forcing

NARCIS (Netherlands)

van der Linden, S.J.A.; Baas, P.; van Hooft, J.A.; van Hooijdonk, I.G.S.; Bosveld, F.C.; van de Wiel, B.J.H.

2017-01-01

Geostrophic wind speed data, derived from pressure observations, are used in combination with tower measurements to investigate the nocturnal stable boundary layer at Cabauw (The Netherlands). Since the geostrophic wind speed is not directly influenced by local nocturnal stability, it may be

GRILLIX. A 3D turbulence code for magnetic fusion devices based on a field line map

International Nuclear Information System (INIS)

Stegmeir, Andreas Korbinian

2015-01-01

The complex geometry in the scrape-off layer of tokamaks poses problems to existing turbulence codes. The usually employed field aligned coordinates become ill defined at the separatrix. Therefore the parallel code GRILLIX was developed, which is based on a field line map. This allows simulations in additional complex geometries, especially across the separatrix. A new discretisation, based on the support operator method, for the highly anisotropic diffusion was developed and applied to a simple turbulence model (Hasegawa-Wakatani).

Level crossings, excess times, and transient plasma–wall interactions in fusion plasmas

Energy Technology Data Exchange (ETDEWEB)

Theodorsen, A., E-mail: audun.theodorsen@uit.no; Garcia, O. E., E-mail: odd.erik.garcia@uit.no [Department of Physics and Technology, UiT The Arctic University of Norway, N-9037 Tromsø (Norway)

2016-04-15

Based on a stochastic model for intermittent fluctuations in the boundary region of magnetically confined plasmas, an expression for the level crossing rate is derived from the joint distribution of the process and its derivative. From this the average time spent by the process above a certain threshold level is obtained. This provides novel predictions of plasma–wall interactions due to transient transport events associated with a radial motion of blob-like structures in the scrape-off layer.

Local Orientation and the Evolution of Foraging: Changes in Decision Making Can Eliminate Evolutionary Trade-offs

Science.gov (United States)

van der Post, Daniel J.; Semmann, Dirk

2011-01-01

Information processing is a major aspect of the evolution of animal behavior. In foraging, responsiveness to local feeding opportunities can generate patterns of behavior which reflect or “recognize patterns” in the environment beyond the perception of individuals. Theory on the evolution of behavior generally neglects such opportunity-based adaptation. Using a spatial individual-based model we study the role of opportunity-based adaptation in the evolution of foraging, and how it depends on local decision making. We compare two model variants which differ in the individual decision making that can evolve (restricted and extended model), and study the evolution of simple foraging behavior in environments where food is distributed either uniformly or in patches. We find that opportunity-based adaptation and the pattern recognition it generates, plays an important role in foraging success, particularly in patchy environments where one of the main challenges is “staying in patches”. In the restricted model this is achieved by genetic adaptation of move and search behavior, in light of a trade-off on within- and between-patch behavior. In the extended model this trade-off does not arise because decision making capabilities allow for differentiated behavioral patterns. As a consequence, it becomes possible for properties of movement to be specialized for detection of patches with more food, a larger scale information processing not present in the restricted model. Our results show that changes in decision making abilities can alter what kinds of pattern recognition are possible, eliminate an evolutionary trade-off and change the adaptive landscape. PMID:21998571

The Experimental Measurement of Local and Bulk Oxygen Transport Resistances in the Catalyst Layer of Proton Exchange Membrane Fuel Cells.

Science.gov (United States)

Wang, Chao; Cheng, Xiaojing; Lu, Jiabin; Shen, Shuiyun; Yan, Xiaohui; Yin, Jiewei; Wei, Guanghua; Zhang, Junliang

2017-12-07

Remarkable progress has been made in reducing the cathodic Pt loading of PEMFCs; however, a huge performance loss appears at high current densities, indicating the existence of a large oxygen transport resistance associated with the ultralow Pt loading catalyst layer. To reduce the Pt loading without sacrificing cell performance, it is essential to illuminate the oxygen transport mechanism in the catalyst layer. Toward this goal, an experimental approach to measure the oxygen transport resistance in catalyst layers is proposed and realized for the first time in this study. The measuring approach involves a dual-layer catalyst layer design, which consists of a dummy catalyst layer and a practical catalyst layer, followed by changing the thickness of dummy layer to respectively quantify the local and bulk resistances via limiting current measurements combined with linear extrapolation. The experimental results clearly reveal that the local resistance dominates the total resistance in the catalyst layer.

Localization of elastic layers by correlated disorder

International Nuclear Information System (INIS)

Balents, L.

1993-01-01

The equilibrium behavior of a system of elastic layers under tension in the presence of correlated disorder is studied using functional renormalization group techniques. The model exhibits many of the features of the Bose-glass phase of type-II superconductors induced by columnar defects, but may be more directly applicable to charge density waves, incommensurate striped magnetic phases, stacked membranes under tension, vicinal crystal surfaces, or superconducting ''vortex-chains''. Below five dimensions, an epsilon expansion for the stable zero-temperature fixed point yields the properties of the glassy phase. Transverse to the direction of correlation, the randomness induces logarithmic growth of displacements. The absence of a response to a weak applied transverse field (transverse Meissner effect) is demonstrated analytically. In this simple model, the localized phase is stable to point disorder, in contrast to the behavior in the presence of dislocations, in which the converse is believed to be true. (orig.)

Localization length and fractal dimension of band centre states for 1-d off-diagonal disordered systems

International Nuclear Information System (INIS)

Roman, E.; Wiecko, C.

1985-08-01

We study and characterize the eigenstates near the centre of the band of a 1-d tight binding model with off-diagonal disorder Wsub(T). We find a new exponent for the localization length lambda on an energy-dependent range of disorder Wsub(T). We correlate this feature with a change of structure of the wave-function displayed by the behaviour of its fractal dimensionality. (author)

Self-defensive antibiotic-loaded layer-by-layer coatings: Imaging of localized bacterial acidification and pH-triggering of antibiotic release.

Science.gov (United States)

Albright, Victoria; Zhuk, Iryna; Wang, Yuhao; Selin, Victor; van de Belt-Gritter, Betsy; Busscher, Henk J; van der Mei, Henny C; Sukhishvili, Svetlana A

2017-10-01

Self-defensive antibiotic-loaded coatings have shown promise in inhibiting growth of pathogenic bacteria adhering to biomaterial implants and devices, but direct proof that their antibacterial release is triggered by bacterially-induced acidification of the immediate environment under buffered conditions remained elusive. Here, we demonstrate that Staphylococcus aureus and Escherichia coli adhering to such coatings generate highly localized acidification, even in buffered conditions, to activate pH-triggered, self-defensive antibiotic release. To this end, we utilized chemically crosslinked layer-by-layer hydrogel coatings of poly(methacrylic acid) with a covalently attached pH-sensitive SNARF-1 fluorescent label for imaging, and unlabeled-antibiotic (gentamicin or polymyxin B) loaded coatings for antibacterial studies. Local acidification of the coatings induced by S. aureus and E. coli adhering to the coatings was demonstrated by confocal-laser-scanning-microscopy via wavelength-resolved imaging. pH-triggered antibiotic release under static, small volume conditions yielded high bacterial killing efficiencies for S. aureus and E. coli. Gentamicin-loaded films retained their antibacterial activity against S. aureus under fluid flow in buffered conditions. Antibacterial activity increased with the number of polymer layers in the films. Altogether, pH-triggered, self-defensive antibiotic-loaded coatings become activated by highly localized acidification in the immediate environment of an adhering bacterium, offering potential for clinical application with minimized side-effects. Polymeric coatings were created that are able to uptake and selectively release antibiotics upon stimulus by adhering bacteria in order to understand the fundamental mechanisms behind pH-triggered antibiotic release as a potential way to prevent biomaterial-associated infections. Through fluorescent imaging studies, this work importantly shows that adhering bacteria produce highly localized p

Dynamics of snap-off and pore-filling events during two-phase fluid flow in permeable media.

Science.gov (United States)

Singh, Kamaljit; Menke, Hannah; Andrew, Matthew; Lin, Qingyang; Rau, Christoph; Blunt, Martin J; Bijeljic, Branko

2017-07-12

Understanding the pore-scale dynamics of two-phase fluid flow in permeable media is important in many processes such as water infiltration in soils, oil recovery, and geo-sequestration of CO 2 . The two most important processes that compete during the displacement of a non-wetting fluid by a wetting fluid are pore-filling or piston-like displacement and snap-off; this latter process can lead to trapping of the non-wetting phase. We present a three-dimensional dynamic visualization study using fast synchrotron X-ray micro-tomography to provide new insights into these processes by conducting a time-resolved pore-by-pore analysis of the local curvature and capillary pressure. We show that the time-scales of interface movement and brine layer swelling leading to snap-off are several minutes, orders of magnitude slower than observed for Haines jumps in drainage. The local capillary pressure increases rapidly after snap-off as the trapped phase finds a position that is a new local energy minimum. However, the pressure change is less dramatic than that observed during drainage. We also show that the brine-oil interface jumps from pore-to-pore during imbibition at an approximately constant local capillary pressure, with an event size of the order of an average pore size, again much smaller than the large bursts seen during drainage.

Kinetic neoclassical transport in the H-mode pedestal

Energy Technology Data Exchange (ETDEWEB)

Battaglia, D. J.; Chang, C. S.; Ku, S.; Grierson, B. A. [Princeton Plasma Physics Laboratory, P.O. Box 451, Princeton, New Jersey 08540 (United States); Burrell, K. H.; Grassie, J. S. de [General Atomics, P.O. Box 85608, San Diego, California 92186-5608 (United States)

2014-07-15

Multi-species kinetic neoclassical transport through the QH-mode pedestal and scrape-off layer on DIII-D is calculated using XGC0, a 5D full-f particle-in-cell drift-kinetic solver with self-consistent neutral recycling and sheath potentials. Quantitative agreement between the flux-driven simulation and the experimental electron density, impurity density, and orthogonal measurements of impurity temperature and flow profiles is achieved by adding random-walk particle diffusion to the guiding-center drift motion. The radial electric field (E{sub r}) that maintains ambipolar transport across flux surfaces and to the wall is computed self-consistently on closed and open magnetic field lines and is in excellent agreement with experiment. The E{sub r} inside the separatrix is the unique solution that balances the outward flux of thermal tail deuterium ions against the outward neoclassical electron flux and inward pinch of impurity and colder deuterium ions. Particle transport in the pedestal is primarily due to anomalous transport, while the ion heat and momentum transport are primarily due to the neoclassical transport. The full-f treatment quantifies the non-Maxwellian energy distributions that describe a number of experimental observations in low-collisionallity pedestals on DIII-D, including intrinsic co-I{sub p} parallel flows in the pedestal, ion temperature anisotropy, and large impurity temperatures in the scrape-off layer.

RF Rectification on LAPD and NSTX: the relationship between rectified currents and potentials

Science.gov (United States)

Perkins, R. J.; Carter, T.; Caughman, J. B.; van Compernolle, B.; Gekelman, W.; Hosea, J. C.; Jaworski, M. A.; Kramer, G. J.; Lau, C.; Martin, E. H.; Pribyl, P.; Tripathi, S. K. P.; Vincena, S.

2017-10-01

RF rectification is a sheath phenomenon important in the fusion community for impurity injection, hot spot formation on plasma-facing components, modifications of the scrape-off layer, and as a far-field sink of wave power. The latter is of particular concern for the National Spherical Torus eXperiment (NSTX), where a substantial fraction of the fast-wave power is lost to the divertor along scrape-off layer field lines. To assess the relationship between rectified currents and rectified voltages, detailed experiments have been performed on the Large Plasma Device (LAPD). An electron current is measured flowing out of the antenna and into the limiters, consistent with RF rectification with a higher RF potential at the antenna. The scaling of this current with RF power will be presented. The limiters are also floated to inhibit this DC current; the impact of this change on plasma-potential and wave-field measurements will be shown. Comparison to data from divertor probes in NSTX will be made. These experiments on a flexible mid-sized experiment will provide insight and guidance into the effects of ICRF on the edge plasma in larger fusion experiments. Funded by the DOE OFES (DE-FC02-07ER54918 and DE-AC02-09CH11466), NSF (NSF- PHY 1036140), and the Univ. of California (12-LR- 237124).

Automatic localization of the prostate for on-line or off-line image-guided radiotherapy

International Nuclear Information System (INIS)

Smitsmans, Monique H.P.; Wolthaus, Jochem W.H.; Artignan, Xavier; Bois, Josien de; Jaffray, David A.; Lebesque, Joos V.; Herk, Marcel van

2004-01-01

Purpose: With higher radiation dose, higher cure rates have been reported in prostate cancer patients. The extra margin needed to account for prostate motion, however, limits the level of dose escalation, because of the presence of surrounding organs at risk. Knowledge of the precise position of the prostate would allow significant reduction of the treatment field. Better localization of the prostate at the time of treatment is therefore needed, e.g. using a cone-beam computed tomography (CT) system integrated with the linear accelerator. Localization of the prostate relies upon manual delineation of contours in successive axial CT slices or interactive alignment and is fairly time-consuming. A faster method is required for on-line or off-line image-guided radiotherapy, because of prostate motion, for patient throughput and efficiency. Therefore, we developed an automatic method to localize the prostate, based on 3D gray value registration. Methods and materials: A study was performed on conventional repeat CT scans of 19 prostate cancer patients to develop the methodology to localize the prostate. For each patient, 8-13 repeat CT scans were made during the course of treatment. First, the planning CT scan and the repeat CT scan were registered onto the rigid bony structures. Then, the delineated prostate in the planning CT scan was enlarged by an optimum margin of 5 mm to define a region of interest in the planning CT scan that contained enough gray value information for registration. Subsequently, this region was automatically registered to a repeat CT scan using 3D gray value registration to localize the prostate. The performance of automatic prostate localization was compared to prostate localization using contours. Therefore, a reference set was generated by registering the delineated contours of the prostates in all scans of all patients. Gray value registrations that showed large differences with respect to contour registrations were detected with a χ 2

The resonance susceptibility of two-layer exchange-coupled ferromagnetic film with a combined uniaxial and cubic anisotropy in the layers

Energy Technology Data Exchange (ETDEWEB)

Shul’ga, N.V., E-mail: shulga@anrb.ru; Doroshenko, R.A.

2016-12-01

A numerical investigation of the resonance dynamic susceptibility of ferromagnetic exchange-coupled two-layer films with a combined cubic and uniaxial magnetic anisotropy of the layers has been performed. It has been found that the presence of cubic anisotropy leads to the fact that much of the off-diagonal components of the dynamic susceptibility are nonzero. The change of the ferromagnetic resonance frequencies and dynamic susceptibility upon the magnetization along the [100], [010], and [011] directions have been calculated. The evolution of the profile of the dynamic susceptibility occurring during the magnetization has been described. The impact of changes in the distribution of equilibrium and dynamic components of the magnetization on the dependences of the components of the dynamic susceptibility and the ferromagnetic resonance frequency on the external magnetic fields has been discussed. - Highlights: • The extremes in the dependences of integrated dynamic susceptibility components are observed at low fields. • Lower extremes can be observed at a shift of the localization of the lower FMR mode toward the interface between the layers. • The features of the distribution of the dynamic susceptibility over the thickness have been discussed. • The cubic anisotropy leads to the fact that the off-diagonal integrated dynamic susceptibility components are essential. • FMR signal can be excited in vicinity of the interlayer boundary.

A New Spectral Local Linearization Method for Nonlinear Boundary Layer Flow Problems

Directory of Open Access Journals (Sweden)

S. S. Motsa

2013-01-01

Full Text Available We propose a simple and efficient method for solving highly nonlinear systems of boundary layer flow problems with exponentially decaying profiles. The algorithm of the proposed method is based on an innovative idea of linearizing and decoupling the governing systems of equations and reducing them into a sequence of subsystems of differential equations which are solved using spectral collocation methods. The applicability of the proposed method, hereinafter referred to as the spectral local linearization method (SLLM, is tested on some well-known boundary layer flow equations. The numerical results presented in this investigation indicate that the proposed method, despite being easy to develop and numerically implement, is very robust in that it converges rapidly to yield accurate results and is more efficient in solving very large systems of nonlinear boundary value problems of the similarity variable boundary layer type. The accuracy and numerical stability of the SLLM can further be improved by using successive overrelaxation techniques.

Study of flow control by localized volume heating in hypersonic boundary layers

Science.gov (United States)

Keller, M. A.; Kloker, M. J.; Kirilovskiy, S. V.; Polivanov, P. A.; Sidorenko, A. A.; Maslov, A. A.

2014-12-01

Boundary-layer flow control is a prerequisite for a safe and efficient operation of future hypersonic transport systems. Here, the influence of an electric discharge—modeled by a heat-source term in the energy equation—on laminar boundary-layer flows over a flat plate with zero pressure gradient at Mach 3, 5, and 7 is investigated numerically. The aim was to appraise the potential of electro-gasdynamic devices for an application as turbulence generators in the super- and hypersonic flow regime. The results with localized heat-source elements in boundary layers are compared to cases with roughness elements serving as classical passive trips. The numerical simulations are performed using the commercial code ANSYS FLUENT (by ITAM) and the high-order finite-difference DNS code NS3D (by IAG), the latter allowing for the detailed analysis of laminar flow instability. For the investigated setups with steady heating, transition to turbulence is not observed, due to the Reynolds-number lowering effect of heating.

Comparison of WRF local and nonlocal boundary layer Physics in Greater Kuala Lumpur, Malaysia

Science.gov (United States)

Ooi, M. C. G.; Chan, A.; Kumarenthiran, S.; Morris, K. I.; Oozeer, M. Y.; Islam, M. A.; Salleh, S. A.

2018-02-01

The urban boundary layer (UBL) is the internal advection layer of atmosphere above urban region which determines the exchanges of momentum, water and other atmospheric constituents between the urban land surface and the free troposphere. This paper tested the performance of three planetary boundary layer (PBL) physics schemes of Weather Research and Forecast (WRF) software to ensure the appropriate representation of vertical structure of UBL in Greater Kuala Lumpur (GKL). Comparison was conducted on the performance of respective PBL schemes to generate vertical and near-surface weather profile and rainfall. Mellor-Yamada- Janjíc (MYJ) local PBL scheme coupled with Eta MM5 surface layer scheme was found to predict the near-surface temperature and wind profile and mixing height better than the nonlocal schemes during the intermonsoonal period with least influences of the synoptic background weather.

Effect of transmitter turn-off time on transient soundings

Science.gov (United States)

Fitterman, D.V.; Anderson, W.L.

1987-01-01

A general procedure for computing the effect of non-zero turn-off time on the transient electromagnetic response is presented which can be applied to forward and inverse calculation methods for any transmitter-receiver configuration. We consider in detail the case of a large transmitter loop which has a receiver coil located at the center of the loop (central induction or in-loop array). For a linear turn-off ramp of width t0, the voltage response is shown to be the voltage due to an ideal step turn-off averaged over windows of width t0. Thus the effect is similar to that obtained by using averaging windows in the receiver. In general when time zero is taken to be the end of the ramp, the apparent resistivity increases for a homogeneous half-space over a limited time range. For time zero taken to be the start of the ramp the apparent resistivity is affected in the opposite direction. The effect of the ramp increases with increasing t0 and first-layer resistivity, is largest during the intermediate stage, and decreases with increasing time. It is shown that for a ramp turn-off, there is no effect in the early and late stages. For two-layered models with a resistive first layer (??1>??2), the apparent resistivity is increased in the intermediate stage. When the first layer is more conductive than the second layer (??1interpretation as shown by field examples; the influence is the greatest on near-surface layer parameters. ?? 1987.

Filamentary probe on the COMPASS tokamak

Czech Academy of Sciences Publication Activity Database

Kovařík, Karel; Ďuran, Ivan; Stöckel, Jan; Seidl, Jakub; Adámek, Jiří; Spolaore, M.; Vianello, N.; Háček, Pavel; Hron, Martin; Pánek, Radomír

2017-01-01

Roč. 88, č. 3 (2017), č. článku 035106. ISSN 0034-6748 R&D Projects: GA MŠk(CZ) 8D15001; GA ČR(CZ) GA15-10723S; GA ČR(CZ) GA16-25074S Institutional support: RVO:61389021 Keywords : tokamak * filaments * scrape-off layer Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: 2.11 Other engineering and technologies Impact factor: 1.515, year: 2016 http://aip.scitation.org/doi/10.1063/1.4977591

Heat and particle transport of sol/divertor plasma in the W-shaped divertor on JT-60U

International Nuclear Information System (INIS)

Asakura, N.; Sakurai, S.; Hosogane, N.

1999-01-01

The plasma profile and parallel flow in the scrape-off layer (SOL) were systematically measured using Mach probes installed at the midplane and the divertor x-point. Quantitative evaluation of a parallel flow: naturally produced in a torus to keep the pressure constant along the field line, was consistent with the measurement. Geometry effects of the W-shaped divertor on the divertor plasma and particle recycling at the newly installed baffle plates were evaluated quantitatively using the edge plasma data. (author)

Analysis of divertor asymmetry using a simple five-point model

International Nuclear Information System (INIS)

Hayashi, Nobuhiko; Takizuka, Tomonori; Hatayama, Akiyoshi; Ogasawara, Masatada.

1997-03-01

A simple five-point model of the scrape-off layer (SOL) plasma outside the separatrix of a diverted tokamak has been developed to study the inside/outside divertor asymmetry. The SOL current, gas pumping/puffing in the divertor region, and divertor plate biasing are included in this model. Gas pumping/puffing and biasing are shown to control divertor asymmetry. In addition, the SOL current is found to form asymmetric solutions without external controls of gas pumping/puffing and biasing. (author)

Analytical solution for the mode conversion equations with steep exponential density profiles

International Nuclear Information System (INIS)

Alava, M.J.; Heikkinen, J.A.

1992-01-01

A general analytical solution for the converted power from the fast magnetosonic wave to an ion Bernstein wave in a magnetized plasma with an exponential steeply increasing density profile is given in the closed form. The solution covers both the conversion at the lower-hybrid resonance and the conversion through the density gradient for small parallel wave numbers. As an application, the conversion coefficients at the scrape-off layer plasma are estimated in the context of ion cyclotron heating of a tokamak plasma

Statistical analysis of temporal and spatial evolution of in-vessel dust particles in KSTAR

International Nuclear Information System (INIS)

Kim, Kyung-Rae; Hong, Suk-Ho; Nam, Yong-Un; Jung, Jinil; Kim, Woong-Chae

2013-01-01

Images of wide-angle visible standard CCD cameras contain information on in-vessel dusts such as dust creation events (DCEs) that occur during plasma operations, and their velocity. Analyzing the straight line-like dust traces in the shallow cylindrical shell-structured scrape-off layer along the vacuum vessel, a database on the short/long term temporal evolutions, spatial locations of DCEs caused by plasma–dust interaction, and the dust velocity distribution are built. We have studied DCEs of 2010 and 2011 KSTAR campaign

Integrated modelling of material migration and target plate power handling at JET

International Nuclear Information System (INIS)

Coster, D.P.; Bonnin, X.; Chankin, A.

2005-01-01

The complexity of the tokamak edge and scrape-off layer (SOL) region is such that extrapolation to ITER requires modelling to be pursued through the integration of a number of edge codes, each of which must be thoroughly tested against results from present day machines. This contribution demonstrates how the edge modelling effort at JET is focused on such an approach by considering two examples, target power loading and material erosion and migration, the understanding of which are crucial issues for ITER. (author)

Propagation velocity analysis of a single blob in the SOL

International Nuclear Information System (INIS)

Sugita, Satoru; Yagi, Masatoshi; Itoh, Sanae-I.; Itoh, Kimitaka

2008-01-01

Nonlinear simulation of plasma blob propagation in the tokamak scrape-off layer is reported. Three types of model equations are introduced and the simulation results are compared. It is found that in the parameter regime where the intercharge instability appears during the propagation process, the theoretical model of propagation velocity determined by the initial blob size provides a good approximation of the simulation results. In the regime where the Kelvin-Helmholtz instability appears, however, the blob velocity saturates at a lower value. (author)

The role of the density profile in the ASDEX-Upgrade pedestal structure

Czech Academy of Sciences Publication Activity Database

Dunne, M.G.; Potzel, S.; Reimold, F.; Wischmeier, M.; Wolfrum, E.; Frassinetti, L.; Beurskens, M.; Bílková, Petra; Cavedon, M.; Fischer, R.; Kurzan, B.; Laggner, F.M.; McDermott, R.M.; Tardini, G.; Trier, E.; Viezzer, E.; Willensdorfer, M.

2017-01-01

Roč. 59, č. 1 (2017), č. článku 014017. ISSN 0741-3335. [EPS 2016: Conference on Plasma Physics/43./. Leuven, 04.07.2016-08.07.2016] EU Projects: European Commission(XE) 633053 - EUROfusion Institutional support: RVO:61389021 Keywords : pedestal * scrape-off layer * peeling-balooning * prediction Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 2.392, year: 2016 http://iopscience.iop.org/0741-3335/59/1/014017

Overview of progress in European medium sized tokamaks towards an integrated plasma-edge/wall solution

OpenAIRE

Meyer, H.; Eich, T.; Beurskens, M.N.A.; Coda, S.; Hakola, A.; Martin, P.; Adamek, J.; Agostini, M.; Aguiam, D.; Ahn, J.; Aho-Mantila, L.; Akers, R.; Albanese, R.; Aledda, R.; Alessi, E.

2017-01-01

Integrating the plasma core performance with an edge and scrape-off layer (SOL) that leads to tolerable heat and particle loads on the wall is a major challenge. The new European medium size tokamak task force (EU-MST) coordinates research on ASDEX Upgrade (AUG), MAST and TCV. This multi-machine approach within EU-MST, covering a wide parameter range, is instrumental to progress in the field, as ITER and DEMO core/pedestal and SOL parameters are not achievable simultaneously in present day de...

[Eng] Voting for Parties or for Candidates? The Trade-Off Between Party and Personal Representation in Spanish Regional and Local Elections

Directory of Open Access Journals (Sweden)

Pablo Barberá

2010-01-01

Full Text Available When voters cast their ballot, are they choosing a candidate or a party? Electoral systems have a significant impact on how this question is answered in each country. As previous literature has shown, some electoral rules foster a more personal representation, while others strengthen the intermediary role of parties. In this paper I maintain that there exists a trade-off between these two types of representation. To empirically verify its existence and how it works, I have chosen local and regional elections in Spain as a case study. Given that they take place simultaneously under similar electoral systems, they can be considered a natural experiment for the study of this trade-off, which allows me to overcome the potential problems of endogeneity present in previous studies. By measuring the significance of ideological closeness and candidate evaluations in voters? decisions at each level, it is shown that the importance of personal representation increases in local elections at the expense of a less frequent use of ideological proximity as an informational shortcut, thus confirming the existence of the trade-off.

High speed movies of turbulence in Alcator C-Mod

International Nuclear Information System (INIS)

Terry, J.L.; Zweben, S.J.; Bose, B.; Grulke, O.; Marmar, E.S.; Lowrance, J.; Mastrocola, V.; Renda, G.

2004-01-01

A high speed (250 kHz), 300 frame charge coupled device camera has been used to image turbulence in the Alcator C-Mod Tokamak. The camera system is described and some of its important characteristics are measured, including time response and uniformity over the field-of-view. The diagnostic has been used in two applications. One uses gas-puff imaging to illuminate the turbulence in the edge/scrape-off-layer region, where D 2 gas puffs localize the emission in a plane perpendicular to the magnetic field when viewed by the camera system. The dynamics of the underlying turbulence around and outside the separatrix are detected in this manner. In a second diagnostic application, the light from an injected, ablating, high speed Li pellet is observed radially from the outer midplane, and fast poloidal motion of toroidal striations are seen in the Li + light well inside the separatrix

Effect of limiter recycling on measured poloidal impurity emission profiles in Tore Supra

International Nuclear Information System (INIS)

Hogan, J.; DeMichelis, C.; Monier-Garbet, P.; Becoulet, M.; Bush, C.; Ghendrih, P.; Guirlet, R.; Hess, W.; Mattioli, M.; Vallet, J.C.

2001-01-01

Poloidal impurity emission profiles measured with the Tore Supra grazing incidence duochromator exhibit a complex spatial structure during ergodic divertor operation with an outboard poloidal guard limiter. As previous measurements with inboard-wall limited plasmas have shown that these profiles give important information about the ergodic field structure, so the contribution of local neon recycling from the limiter-induced plume has been modeled. This permits a discrimination of edge and core transport effects. The BBQ 3D scrape-off layer code calculates the asymmetric contribution to the emission and MIST 1D simulation gives the symmetric part. A systematic increase is observed in the decay rate of neon emission after injection as the ergodic divertor strength is increased. The calculations permit identification of the limiter plume contribution to the profile structure, and, with this identification, the effect of the divertor to enhance impurity efflux can be seen from the decay data

Method of processing radioactive liquid wastes by solidification with cement

International Nuclear Information System (INIS)

Yasumura, Keijiro; Matsuura, Hiroyuki.

1975-01-01

Object: To subject radioactive liquid wastes to a cement solidification treatment after heating and drying it by a thin film scrape-off drier to render it into the form of power, and then molding it into pellets for the treatment. Structure: Radioactive liquid wastes discharged from a nuclear power plant or nuclear reactor are supplied through a storage tank into a thin film scrape-off drier. In the drier, the radioactive liquid wastes are heated to separate the liquid, and the residue is taken out as dry powder from the scrape-off apparatus. The powder obtained in this way is molded into pellets of a desired form. These pellets are then packed in a drum can or similar container, into which cement paste is then poured for solidification. (Moriyama, K.)

Sampling and analysis plan for the gunite and associated tanks interim remedial action, wall coring and scraping at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1998-02-01

This Sampling and Analysis Plan documents the procedures for collecting and analyzing wall core and wall scraping samples from the Gunite and Associated Tanks. These activities are being conducted to support the Comprehensive Environmental Response, Compensation, and Liability Act at the gunite and associated tanks interim remedial action at Oak Ridge National Laboratory in Oak Ridge, Tennessee. The sampling and analysis activities will be performed in concert with sludge retrieval and sluicing of the tanks. Wall scraping and/or wall core samples will be collected from each quadrant in each tank by using a scraping sampler and/or a coring drill deployed by the Houdini robot vehicle. Each sample will be labeled, transported to the Radioactive Materials Analytical Laboratory, and analyzed for physical and radiological characteristics, including total activity, gross alpha, gross beta, radioactive strontium and cesium, and other alpha- and gamma-emitting radionuclides. The data quality objectives process, based on US Environmental Protection Agency guidance, was applied to identify the objectives of this sampling and analysis. The results of the analysis will be used to (1) validate predictions of a strontium concrete diffusion model, (2) estimate the amount of radioactivity remaining in the tank shells, (3) provide information to correlate with measurements taken by the Gunite Tank Isotope Mapping Probe and the Characterization End Effector, and (4) estimate the performance of the wall cleaning system. This revision eliminates wall-scraping samples from all tanks, except Tank W-3. The Tank W-3 experience indicated that the wall scrapper does not collect sufficient material for analysis

Combined Langmuir-magnetic probe measurements of type-I ELMy filaments in the EAST tokamak

Science.gov (United States)

Qingquan, YANG; Fangchuan, ZHONG; Guosheng, XU; Ning, YAN; Liang, CHEN; Xiang, LIU; Yong, LIU; Liang, WANG; Zhendong, YANG; Yifeng, WANG; Yang, YE; Heng, ZHANG; Xiaoliang, Li

2018-06-01

Detailed investigations on the filamentary structures associated with the type-I edge-localized modes (ELMs) should be helpful for protecting the materials of a plasma-facing wall on a future large device. Related experiments have been carefully conducted in the Experimental Advanced Superconducting Tokamak (EAST) using combined Langmuir-magnetic probes. The experimental results indicate that the radially outward velocity of type-I ELMy filaments can be up to 1.7 km s‑1 in the far scrape-off layer (SOL) region. It is remarkable that the electron temperature of these filaments is detected to be ∼50 eV, corresponding to a fraction of 1/6 to the temperature near the pedestal top, while the density (∼ 3× {10}19 {{{m}}}-3) of these filaments could be approximate to the line-averaged density. In addition, associated magnetic fluctuations have been clearly observed at the same time, which show good agreement with the density perturbations. A localized current on the order of ∼100 kA could be estimated within the filaments.

Toroidal asymmetries in divertor impurity influxes in NSTX

Directory of Open Access Journals (Sweden)

F. Scotti

2017-08-01

Full Text Available Toroidal asymmetries in divertor carbon and lithium influxes were observed in NSTX, due to toroidal differences in surface composition, tile leading edges, externally-applied three-dimensional (3D fields and toroidally-localized edge plasma modifications due to radio frequency heating. Understanding toroidal asymmetries in impurity influxes is critical for the evaluation of total impurity sources, often inferred from measurements with a limited toroidal coverage. The toroidally-asymmetric lithium deposition induced asymmetries in divertor lithium influxes. Enhanced impurity influxes at the leading edge of divertor tiles were the main cause of carbon toroidal asymmetries and were enhanced during edge localized modes. Externally-applied 3D fields led to strike point splitting and helical lobes observed in divertor impurity emission, but marginal changes to the toroidally-averaged impurity influxes. Power coupled to the scrape-off layer SOL plasma during radio frequency (RF heating of H-mode discharges enhanced impurity influxes along the non-axisymmetric divertor footprint of flux tubes connecting to plasma in front of the RF antenna.

Effects of boundary conditions on temperature and density in an EXTRAP Z-pinch

International Nuclear Information System (INIS)

Drake, J.R.; Karlsson, P.

1985-08-01

Using the fluid equations, we examine transport in an Extrap configuration by carrying out calculations incorporating model profiles for the density and temperature. The goal of this analysis is to examine the scaling of the pinch equilibrium plasma density, temperature and radius with parameters that are characteristic for Extrap Z-pinches. These parameters include the discharge current, the neutral hydrogen filling density, an oxygen impurity fractional concentration and the condition at the pinch boundary. An Extrap Z-pinch is a pinch discharge where the current channel has a characteristic non-circular cross-section achieved by bounding the discharge by a magnetic separatrix produced when a vacuum octupole magnetic field, generated by currents in external conductors, combines with the self-magnetic field produced by the discharge current. The pinch boundary is changed from a plasma-vacuum boundary to an interface between a high-beta pinch plasma and a low-beta plasma contained in the vacuum magnetic field. The energy that is lost from the pinch region sustains this boundary layer. The introduction of a separatrix boundary around the pinch with four X-point nulls deteriorates the containment of the pinch somewhat. However the presence of the warm, low-beta plasma scrape-off layer, which provides a boundary condition on the pinch, tends to counteract the negative effects of the poorer confinement. Thus the equilibrium parameters that characterize the pinch may not be severely deteriorated by the introduction of the separatrix when the entire configuration, including the scrape-off layer, is considered. (author)

Electric Power Plants and Generation Stations, Power Plants - is a seperate layer, however, we have them included in local building layer as well, Published in 2010, 1:2400 (1in=200ft) scale, Effingham County Government.

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Electric Power Plants and Generation Stations dataset current as of 2010. Power Plants - is a seperate layer, however, we have them included in local building layer...

Time resolved X-ray micro-diffraction measurements of the dynamic local layer response to electric field in antiferroelectric liquid crystals

Energy Technology Data Exchange (ETDEWEB)

Takahashi, Yumiko; Iida, Atuso E-mail: atsuo.iida@kek.jp; Takanishi, Yoichi; Ogasawara, Toyokazu; Takezoe, Hideo

2001-07-21

The time-resolved synchrotron X-ray microbeam diffraction experiment has been carried out to reveal the local layer response to the electric field in the antiferroelectric liquid crystal. The X-ray microbeam of a few {mu}m spatial resolution was obtained with Kirkpatrick-Baez optics. The time-resolved small angle diffraction experiment was performed with a time resolution ranging from 10 {mu}s to a few ms. The reversible local layer change between the horizontal chevron and the quasi-bookshelf structure was confirmed by the triangular wave form. The transient layer response for the step form electric field was observed. The layer response closely related with an electric field induced antiferroelectric to ferroelectric phase transition.

Time resolved X-ray micro-diffraction measurements of the dynamic local layer response to electric field in antiferroelectric liquid crystals

International Nuclear Information System (INIS)

Takahashi, Yumiko; Iida, Atuso; Takanishi, Yoichi; Ogasawara, Toyokazu; Takezoe, Hideo

2001-01-01

The time-resolved synchrotron X-ray microbeam diffraction experiment has been carried out to reveal the local layer response to the electric field in the antiferroelectric liquid crystal. The X-ray microbeam of a few μm spatial resolution was obtained with Kirkpatrick-Baez optics. The time-resolved small angle diffraction experiment was performed with a time resolution ranging from 10 μs to a few ms. The reversible local layer change between the horizontal chevron and the quasi-bookshelf structure was confirmed by the triangular wave form. The transient layer response for the step form electric field was observed. The layer response closely related with an electric field induced antiferroelectric to ferroelectric phase transition

Formation of periodic and localized patterns in an oscillating granular layer.

Energy Technology Data Exchange (ETDEWEB)

Aranson, I.; Tsimring, L. S.; Materials Science Division; Bar Ilan Univ.; Univ. of California at San Diego

1998-02-01

A simple phenomenological model for pattern formation in a vertically vibrated layer of granular particles is proposed. This model exhibits a variety of stable cellular patterns including standing rolls and squares as well as localized excitations (oscillons and worms), similar to recent experimental observations (Umbanhowar et al., 1996). The model is an order parameter equation for the parametrically excited waves coupled to the mass conservation law. The structure and dynamics of the solutions resemble closely the properties of patterns observed in the experiments.

Cross-separatrix Coupling in Nonlinear Global Electrostatic Turbulent Transport in C-2U

Science.gov (United States)

Lau, Calvin; Fulton, Daniel; Bao, Jian; Lin, Zhihong; Binderbauer, Michl; Tajima, Toshiki; Schmitz, Lothar; TAE Team

2017-10-01

In recent years, the progress of the C-2/C-2U advanced beam-driven field-reversed configuration (FRC) experiments at Tri Alpha Energy, Inc. has pushed FRCs to transport limited regimes. Understanding particle and energy transport is a vital step towards an FRC reactor, and two particle-in-cell microturbulence codes, the Gyrokinetic Toroidal Code (GTC) and A New Code (ANC), are being developed and applied toward this goal. Previous local electrostatic GTC simulations find the core to be robustly stable with drift-wave instability only in the scrape-off layer (SOL) region. However, experimental measurements showed fluctuations in both regions; one possibility is that fluctuations in the core originate from the SOL, suggesting the need for non-local simulations with cross-separatrix coupling. Current global ANC simulations with gyrokinetic ions and adiabatic electrons find that non-local effects (1) modify linear growth-rates and frequencies of instabilities and (2) allow instability to move from the unstable SOL to the linearly stable core. Nonlinear spreading is also seen prior to mode saturation. We also report on the progress of the first turbulence simulations in the SOL. This work is supported by the Norman Rostoker Fellowship.

Diagnostics for the Biased Electrode Experiment on NSTX

International Nuclear Information System (INIS)

Roquemore, A.L.; Zweben, S.J.; Bush, C.E.; Kaita, R.; Marsalsa, R.J.; Maqueda, R.J.

2009-01-01

A linear array of four small biased electrodes was installed in NSTX in an attempt to control the width of the scrape-off layer (SOL) by creating a strong local poloidal electric field. The set of electrodes were separated poloidally by a 1 cm gap between electrodes and were located slightly below the midplane of NSTX, 1 cm behind the RF antenna and oriented so that each electrode is facing approximately normal to the magnetic field. Each electrode can be independently biased to ± 100 volts. Present power supplies limit the current on two electrodes to 30 amps the other two to 10 amps each. The effect of local biasing was measured with a set of Langmuir probes placed between the electrodes and another set extending radially outward from the electrodes, and also by the gas puff imaging diagnostic (GPI) located 1 m away along the magnetic field lines intersecting the electrodes. Two fast cameras were also aimed directly at the electrode array. The hardware and controls of the biasing experiment will be presented and the initial effects on local plasma parameters will be discussed

Localization of metabotropic glutamate receptors in the outer plexiform layer of the goldfish retina

NARCIS (Netherlands)

Joselevitch, Christina; Klooster, Jan; Kamermans, Maarten

2007-01-01

We studied the localization of metabotropic glutamate receptors (mGluRs) in the goldfish outer plexiform layer by light-and electron-microscopical immunohistochemistry. The mGluR1alpha antibody labeled putative ON-type bipolar cell dendrites and horizontal cell processes in both rod spherules and

Management of gingiva hyperpigmentasi with combine of scalpel scraping technique and gingivo abrasion technique (Case report

Directory of Open Access Journals (Sweden)

Shek Wendy

2016-06-01

Full Text Available Aesthetic factor is an important factor in supporting the person's appearance, especially when a person smiles. Beautifull smiles form of harmonization between the teeth and gums as part of the oral cavity. One of overall aspect that has an important role in providing the overall aesthetic impression is normal gum color that pink coral. Brown or black gums are often become the complaint that interfere with appearance, especially in patients who have a habit of smoking. Pigmentation caused by melanin hyperpigmentation and usually does not present a medical problems, so patients are not aware of it. Surgical method with the scalpel scraping technique and gingivo abrasion technique using high speed carbide bur has been widely used as a method of gingival depigmentation. This method is easily done, simple and can be done in a relatively short time. In this case report presented regarding the management of patients with gingival hyperpigmentation of the maxilla and mandible were treated with surgical method using a scalpel scraping technique combined with gingivo abrasion technique using high speed carbide bur. The result, after 4 weeks follow up, color of the patient's gingival was pink and there is none recurrence of the pigmentation.

3-dimensional plasma-boundary-layer simulations in uncompletely ergodized magnetic fields; 3-dimensionale Plasmarandschicht-Simulationen in unvollstaendig ergodisierten Magnetfeldern

Energy Technology Data Exchange (ETDEWEB)

Harting, Derek M.

2008-03-16

Within this work, a numerical tool, the EMC3/EIRENE code, is presented which solves self-consistently the strongly anisotropic 3D fluid equations for the main plasma (hydrogen) and plasma impurities (e.g. carbon) in an ergodic edge plasma layer. The model equations of the EMC3 code are discussed in detail and essential technical extensions are described and carried out, which enables realistic simulations of the edge plasma at TEXTOR-DED. In course of the simulations for the different base mode configurations of the DED, it turned out that a helical structure of laminar flux tubes (bunch of field-lines with one poloidal turn) is formed by the resonant perturbation field. Due to the dominant parallel streaming to the wall being the loss channel in this helical laminar flux tubes and the perpendicular transport into them being the source channel, the laminar flux tubes act like an extended helical scrape of layer, and thus the density and electron temperature are reduced locally in these flux tubes. Additionally, a promising scenario could be identified in the 3/1 base mode configuration of the DED, where remanent island structures exist near the recycling DED surface. Due to the ionization of the recycled hydrogen atoms in this remanent islands, the density increases strongly in these remanent islands and the electron and ion temperatures are reduced locally. It has been shown that in this case, the recycling is significantly changed and even a local high recycling regime is presumed. Some kinetic corrections on the classical parallel electron heatconductivity and the parallel viscosity of ions were implemented into the EMC3 code. (orig.)

A new extremum seeking technique and its application to maximize RF heating on FTU

International Nuclear Information System (INIS)

Carnevale, D.; Astolfi, A.; Centioli, C.; Podda, S.; Vitale, V.; Zaccarian, L.

2009-01-01

We propose a new global extremum seeking algorithm to optimize the coupling between the emitting Lower Hybrid (LH) antennas and the plasma scrape off layer in the radiofrequency (RF) heating problem in tokamak plasmas. The new algorithm, where the existing disturbances affecting the system are seen as the probing signals, requires less constraining properties than the previous ones and is more robust. In particular, simulation results are presented illustrating the effectiveness of the algorithm on the Lower Hybrid RF heating of the Frascati Tokamak Upgrade (FTU).

A radar study of emigratory flight and layer formation by insects at dawn over southern Britain.

Science.gov (United States)

Reynolds, D R; Smith, A D; Chapman, J W

2008-02-01

Radar observations have consistently shown that high-altitude migratory flight in insects generally occurs after mass take-off at dusk or after take-off over a more extended period during the day (in association with the growth of atmospheric convection). In this paper, we focus on a less-studied third category of emigration - the 'dawn take-off' - as recorded by insect-monitoring radars during the summer months in southern England. In particular, we describe occasions when dawn emigrants formed notable layer concentrations centred at altitudes ranging from ca. 240 m to 700 m above ground, very probably due to the insects responding to local temperature maxima in the atmosphere, such as the tops of inversions. After persisting for several hours through the early morning, the layers eventually merged into the insect activity building up later in the morning (from 06.00-08.00 h onwards) in conjunction with the development of daytime convection. The species forming the dawn layers have not been positively identified, but their masses lay predominantly in the 16-32 mg range, and they evidently formed a fauna quite distinct from that in flight during the previous night. The displacement and common orientation (mutual alignment) characteristics of the migrants are described.

Layer-by-layer assembled TiO2 films with high ultraviolet light-shielding property

International Nuclear Information System (INIS)

Li, Xiaozhou; Wang, Lin; Pei, Yuxin; Jiang, Jinqiang

2014-01-01

Ultraviolet (UV) B is hazardous to human, plants and animals. With the rapid growth of ozone holes over the earth, the exploration of optical materials that can cut off harmful UV radiation is important. In this work, fusiform TiO 2 nanoparticles were synthesized by a hydrothermal synthesis method. The thin films assembled with TiO 2 nanoparticles and oppositely charged polyelectrolytes were fabricated via a layer-by-layer assembly method. The fabrication of poly(ethylene imine) (PEI)/TiO 2 multilayer films was verified by ultraviolet–visible spectra measurements, scanning electron microscopy and atomic force microscopy. The as-prepared PEI/TiO 2 multilayer films can effectively absorb harmful UVB light and filter off visible light. Most importantly, the PEI/TiO 2 films can be deposited directly on various kinds of hydrophilic substrates such as quartz, glass, silicon and hydrophobic substrates such as polystyrene, polypropylene, polyethylene and polymethyl methacrylate when the hydrophilic substrates were modified to obtain a hydrophilic surface. - Highlights: • PEI/TiO 2 films were fabricated via a layer-by-layer self-assembly method. • The films could effectively absorb harmful UVB light and filter off visible light. • The films could deposit directly on either hydrophilic or hydrophobic substrates

Edge Sheared Flows and Blob Dynamics

Energy Technology Data Exchange (ETDEWEB)

Myra, J.; D' Ippolito, D.; Russell, D., E-mail: jrmyra@lodestar.com [Lodestar Research Corporation, Boulder (United States); Davis, W. M.; Zweben, S. [Princeton Plasma Physics Laboratory, Princeton (United States); Terry, J.; LaBombard, B. [Massachusetts Institute of Technology, Cambridge (United States)

2012-09-15

Full text: A study of sheared flows in the edge and scrape-off layer (SOL) and their interaction with blob-filaments is presented. Edge sheared flows are believed to be important for the L-H, and H-L transitions. Blob generation and dynamics impacts both the (near-separatrix) scrape-off-layer (SOL) width critical for power handling in the divertor, and the interaction of plasma in the far SOL with plasma-facing components. These topics are critical for ITER and future devices. A fluid-based 2D curvature-interchange model embedded in the SOLT code is employed to study these issues. Sheared binormal flows both regulate the power flux crossing the separatrix and control the character of emitted turbulence structures such as blob-filaments. At a critical power level (depending on parameters) the laminar flows containing intermittent, but bound, structures give way to full-blown blob emissions signifying a transition from quasi-diffusive to convective transport. In order to diagnose sheared flows in experiments and assess their interaction with blobs, a blob-tracking algorithm has been developed and applied to both NSTX and Alcator C-Mod data. Blob motion and ellipticity can be affected by sheared flows, and are diagnosed and compared with seeded blob simulations. A picture of the interaction of blobs and sheared flows is emerging from advances in the theory and simulation of edge turbulence, combined with ever-improving capabilities for edge diagnostics and their analysis. (author)

SU-G-IeP2-05: Effect of Localizer Type and Patient Off-Centering On CT Radiation Dose with Use of Automatic Tube Current Modulation

International Nuclear Information System (INIS)

Ruan, C; Sodickson, A; Hamberg, L

2016-01-01

Purpose: Apparent patient size in CT localizers varies with localizer type and patient positioning, resulting in variation in effective mAs as guided by Tube Current Modulation (TCM). Our aim was to investigate the effects of vertical off-centering on CTDI-vol when using different localizer types and TCM strengths. Methods: A CTDI body phantom was scanned using an abdominal protocol with three TCM strengths (Siemens Definition AS40, CAREDose4D; very weak, average, very strong). Data was acquired at 11 table height positions; with phantom center at isocenter and at 10 other positions between 142mm below and 53mm above. At each position, scans were acquired using 5 different localizer types: PA, AP, Lateral, PA+Lateral, and Lateral+PA. CTDI-vol was recorded for the 165 combinations of table height, localizer type, and TCM strength, and magnification factors measured from localizer images. Results: Magnification factors from AP and PA localizers ranged from 0.79–1.11 and 1.35–0.91, respectively from lowest to highest positions (highest with phantom located closest to X-ray tube), with a smaller impact when using Lateral, PA+Lateral, Lateral+PA localizer types, all of which behaved similarly. For an average TCM strength and PA localizer, CTDI-vol ranged from 75% higher to 12% lower than the isocenter value for the lowest to highest table positions, respectively. For table positions ranging from lowest to highest, CTDI-vol ranged from −23% to 17% for AP, from −8% to 0.3% for lateral and from −7% to 1% for a combination of PA and Lateral in either order. Similar behavior was found for different TCM strengths, but effects were more pronounced for very strong compared with very weak modulation strengths. Conclusion: Patient off-centering substantially impacts radiation dose, which depends on the amount of vertical offcentering and type of the localizer used. The combination of PA and Lateral localizers is most robust against effects of patient off-centering.

SU-G-IeP2-05: Effect of Localizer Type and Patient Off-Centering On CT Radiation Dose with Use of Automatic Tube Current Modulation

Energy Technology Data Exchange (ETDEWEB)

Ruan, C; Sodickson, A; Hamberg, L [Brigham and Women’s Hospital, Boston, MA (United States)

2016-06-15

Purpose: Apparent patient size in CT localizers varies with localizer type and patient positioning, resulting in variation in effective mAs as guided by Tube Current Modulation (TCM). Our aim was to investigate the effects of vertical off-centering on CTDI-vol when using different localizer types and TCM strengths. Methods: A CTDI body phantom was scanned using an abdominal protocol with three TCM strengths (Siemens Definition AS40, CAREDose4D; very weak, average, very strong). Data was acquired at 11 table height positions; with phantom center at isocenter and at 10 other positions between 142mm below and 53mm above. At each position, scans were acquired using 5 different localizer types: PA, AP, Lateral, PA+Lateral, and Lateral+PA. CTDI-vol was recorded for the 165 combinations of table height, localizer type, and TCM strength, and magnification factors measured from localizer images. Results: Magnification factors from AP and PA localizers ranged from 0.79–1.11 and 1.35–0.91, respectively from lowest to highest positions (highest with phantom located closest to X-ray tube), with a smaller impact when using Lateral, PA+Lateral, Lateral+PA localizer types, all of which behaved similarly. For an average TCM strength and PA localizer, CTDI-vol ranged from 75% higher to 12% lower than the isocenter value for the lowest to highest table positions, respectively. For table positions ranging from lowest to highest, CTDI-vol ranged from −23% to 17% for AP, from −8% to 0.3% for lateral and from −7% to 1% for a combination of PA and Lateral in either order. Similar behavior was found for different TCM strengths, but effects were more pronounced for very strong compared with very weak modulation strengths. Conclusion: Patient off-centering substantially impacts radiation dose, which depends on the amount of vertical offcentering and type of the localizer used. The combination of PA and Lateral localizers is most robust against effects of patient off-centering.

Edge localized mode physics and operational aspects in tokamaks

Energy Technology Data Exchange (ETDEWEB)

Becoulet, M [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Huysmans, G [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Sarazin, Y [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Garbet, X [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Ghendrih, Ph [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Rimini, F [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Joffrin, E [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Litaudon, X [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Monier-Garbet, P [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Ane, J-M [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Thomas, P [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Grosman, A [Association Euratom-CEA, CEA Cadarache, F-13108 St Paul-lez-Durance (France); Parail, V [Euratom/UKAEA Association, Fusion Culham Science Centre, Abingdon, OX14 3EA (United Kingdom); Wilson, H [Euratom/UKAEA Association, Fusion Culham Science Centre, Abingdon, OX14 3EA (United Kingdom); Lomas, P [Euratom/UKAEA Association, Fusion Culham Science Centre, Abingdon, OX14 3EA (United Kingdom); Vries, P de[Euratom/UKAEA Association, Fusion Culham Science Centre, Abingdon, OX14 3EA (United Kingdom); Zastrow, K-D [Euratom/UKAEA Association, Fusion Culham Science Centre, Abingdon, OX14 3EA (United Kingdom); Matthews, G F [Euratom/UKAEA Association, Fusion Culham Science Centre, Abingdon, OX14 3EA (United Kingdom); Lonnroth, J [Euratom/UKAEA Association, Fusion Culham Science Centre, Abingdon, OX14 3EA (United Kingdom); Gerasimov, S [Euratom/UKAEA Association, Fusion Culham Science Centre, Abingdon, OX14 3EA (United Kingdom)] [and others

2003-12-01

Recent progress in experimental and theoretical studies of edge localized mode (ELM) physics is reviewed for the reactor relevant plasma regimes, namely the high confinement regimes, that is, H-modes and advanced scenarios. Theoretical approaches to ELM physics, from a linear ideal magnetohydrodynamic (MHD) stability analysis to non-linear transport models with ELMs are discussed with respect to experimental observations, in particular the fast collapse of pedestal pressure profiles, magnetic measurements and scrape-off layer transport during ELMs. High confinement regimes with different types of ELMs are addressed in this paper in the context of development of operational scenarios for ITER. The key parameters that have been identified at present to reduce the energy losses in Type I ELMs are operation at high density, high edge magnetic shear and high triangularity. However, according to the present experimental scaling for the energy losses in Type I ELMs, the extrapolation of such regimes for ITER leads to unacceptably large heat loads on the divertor target plates exceeding the material limits. High confinement H-mode scenarios at high triangularity and high density with small ELMs (Type II), mixed regimes (Type II and Type I) and combined advanced regimes at high beta{sub p} are discussed for present-day tokamaks. The optimum combination of high confinement and small MHD activity at the edge in Type II ELM scenarios is of interest to ITER. However, to date, these regimes have been achieved in a rather narrow operational window and far from ITER parameters in terms of collisionality, edge safety factor and beta{sub p}. The compatibility of the alternative internal transport barrier (ITB) scenario with edge pedestal formation and ELMs is also addressed. Edge physics issues related to the possible combination of small benign ELMs (Type III, Type II ELMs, quiescent double barrier) and high performance ITBs are discussed for present-day experiments (JET, JT-60U

Edge localized mode physics and operational aspects in tokamaks

International Nuclear Information System (INIS)

Becoulet, M; Huysmans, G; Sarazin, Y; Garbet, X; Ghendrih, Ph; Rimini, F; Joffrin, E; Litaudon, X; Monier-Garbet, P; Ane, J-M; Thomas, P; Grosman, A; Parail, V; Wilson, H; Lomas, P; Vries, P de; Zastrow, K-D; Matthews, G F; Lonnroth, J; Gerasimov, S; Sharapov, S; Gryaznevich, M; Counsell, G; Kirk, A; Valovic, M; Buttery, R; Loarte, A; Saibene, G; Sartori, R; Leonard, A; Snyder, P; Lao, L L; Gohil, P; Evans, T E; Moyer, R A; Kamada, Y; Chankin, A; Oyama, N; Hatae, T; Asakura, N; Tudisco, O; Giovannozzi, E; Crisanti, F; Perez, C P; Koslowski, H R; Eich, T; Sips, A; Horton, L; Hermann, A; Lang, P; Stober, J; Suttrop, W; Beyer, P; Saarelma, S

2003-01-01

Recent progress in experimental and theoretical studies of edge localized mode (ELM) physics is reviewed for the reactor relevant plasma regimes, namely the high confinement regimes, that is, H-modes and advanced scenarios. Theoretical approaches to ELM physics, from a linear ideal magnetohydrodynamic (MHD) stability analysis to non-linear transport models with ELMs are discussed with respect to experimental observations, in particular the fast collapse of pedestal pressure profiles, magnetic measurements and scrape-off layer transport during ELMs. High confinement regimes with different types of ELMs are addressed in this paper in the context of development of operational scenarios for ITER. The key parameters that have been identified at present to reduce the energy losses in Type I ELMs are operation at high density, high edge magnetic shear and high triangularity. However, according to the present experimental scaling for the energy losses in Type I ELMs, the extrapolation of such regimes for ITER leads to unacceptably large heat loads on the divertor target plates exceeding the material limits. High confinement H-mode scenarios at high triangularity and high density with small ELMs (Type II), mixed regimes (Type II and Type I) and combined advanced regimes at high beta p are discussed for present-day tokamaks. The optimum combination of high confinement and small MHD activity at the edge in Type II ELM scenarios is of interest to ITER. However, to date, these regimes have been achieved in a rather narrow operational window and far from ITER parameters in terms of collisionality, edge safety factor and beta p . The compatibility of the alternative internal transport barrier (ITB) scenario with edge pedestal formation and ELMs is also addressed. Edge physics issues related to the possible combination of small benign ELMs (Type III, Type II ELMs, quiescent double barrier) and high performance ITBs are discussed for present-day experiments (JET, JT-60U, DIII-D) in

Effect of gas injection during LH wave coupling at ITER-relevant plasma-wall distances in JET

International Nuclear Information System (INIS)

Ekedahl, A; Goniche, M; Basiuk, V; Delpech, L; Imbeaux, F; Joffrin, E; Loarer, T; Rantamaeki, K; Mailloux, J; Alper, B; Baranov, Y; Beaumont, P; Corrigan, G; Erents, K; Hawkes, N; McDonald, D; Petrzilka, V; Granucci, G; Hobirk, J; Kirov, K

2009-01-01

Good coupling of lower hybrid (LH) waves has been demonstrated in different H-mode scenarios in JET, at high triangularity (δ ∼ 0.4) and at large distance between the last closed flux surface and the LH launcher (up to 15 cm). Local gas injection of D 2 in the region magnetically connected to the LH launcher is used for increasing the local density in the scrape-off layer (SOL). Reciprocating Langmuir probe measurements magnetically connected to the LH launcher indicate that the electron density profile flattens in the far SOL during gas injection and LH power application. Some degradation in normalized H-mode confinement, as given by the H98(y,2)-factor, could be observed at high gas injection rates in these scenarios, but this was rather due to total gas injection and not specifically to the local gas puffing used for LH coupling. Furthermore, experiments carried out in L-mode plasmas in order to evaluate the effect on the LH current drive efficiency, when using local gas injection to improve the coupling, indicate only a small degradation (ΔI LH /I LH ∼ 15%). This effect is largely compensated by the improvement in coupling and thus increase in coupled power when using gas puffing.

Increased mobility and on/off ratio in organic field-effect transistors using low-cost guanine-pentacene multilayers

Science.gov (United States)

Shi, Wei; Zheng, Yifan; Taylor, André D.; Yu, Junsheng; Katz, Howard E.

2017-07-01

Layer-by-layer deposited guanine and pentacene in organic field-effect transistors (OFETs) is introduced. Through adjusting the layer thickness ratio of guanine and pentacene, the tradeoff of two electronic parameters in OFETs, charge carrier mobility and current on/off ratio, was controlled. The charge mobility was enhanced by depositing pentacene over and between guanine layers and by increasing the proportion of pentacene in the layer-by-layer system, while the current on/off ratio was increased via the decreased off current induced by the guanine layers. The tunable device performance was mainly ascribed to the trap and dopant neutralizing properties of the guanine layers, which would decrease the density of free hydroxyl groups in the OFETs. Furthermore, the cost of the devices could be reduced remarkably via the adoption of low-cost guanine.

Far SOL transport and main wall plasma interaction in DIII-D

International Nuclear Information System (INIS)

Rudakov, D.L.; Boedo, J.A.; Moyer, R.A.; Doerner, R.P.; Hollmann, E.M.; Krasheninnikov, S.I.; Pigarov, A.Yu.; Stangeby, P.C.; McLean, A.G.; Watkins, J.G.; Wampler, W.R.; Whyte, D.G.; McKee, G.R.; Zeng, L.; Wang, G.; Brooks, N.H.; Evans, T.E.; Leonard, A.W.; Mahdavi, M.A.; West, W.P.; Wong, C.P.C.; Fenstermacher, M.E.; Groth, M.; Lasnier, C.J.

2005-01-01

Far scrape-off layer (SOL) and near-wall plasma parameters in DIII-D depend strongly on the discharge parameters and confinement regime. In L-mode discharges cross-field transport increases with the average discharge density and flattens far SOL profiles, thus increasing plasma-wall contact. In H-mode between edge localized modes (ELMs), plasma-wall contact is generally weaker than in L-mode. During ELMs plasma fluxes to the wall increase to, or above the L-mode levels. Depending on the discharge conditions ELMs are responsible for 30-90% of the ion flux to the outboard chamber wall. Cross-field fluxes in far SOL are dominated by large amplitude intermittent transport events that may propagate all the way to the outer wall and cause sputtering. A Divertor Material Evaluation System (DiMES) probe containing samples of several ITER-relevant materials including carbon, beryllium and tungsten was exposed to a series of upper single null (USN) discharges as a proxy to measure the first wall erosion. (author)

Mitigation of divertor heat flux by high-frequency ELM pacing with non-fuel pellet injection in DIII-D

Directory of Open Access Journals (Sweden)

A. Bortolon

2017-08-01

Full Text Available Experiments have been conducted on DIII-D investigating high repetition rate injection of non-fuel pellets as a tool for pacing Edge Localized Modes (ELMs and mitigating their transient divertor heat loads. Effective ELM pacing was obtained with injection of Li granules in different H-mode scenarios, at frequencies 3–5 times larger than the natural ELM frequency, with subsequent reduction of strike-point heat flux (Bortolon et al., Nucl. Fus., 56, 056008, 2016. However, in scenarios with high pedestal density (∼6 ×1019m−3, the magnitude of granule triggered ELMs shows a broad distribution, in terms of stored energy loss and peak heat flux, challenging the effectiveness of ELM mitigation. Furthermore, transient heat-flux deposition correlated with granule injections was observed far from the strike-points. Field line tracing suggest this phenomenon to be consistent with particle loss into the mid-plane far scrape-off layer, at toroidal location of the granule injection.

Turbulent edge transport in the Princeton Beta Experiment-Modified high confinement mode

Science.gov (United States)

Tynan, G. R.; Schmitz, L.; Blush, L.; Boedo, J. A.; Conn, R. W.; Doerner, R.; Lehmer, R.; Moyer, R.; Kugel, H.; Bell, R.; Kaye, S.; Okabayashi, M.; Sesnic, S.; Sun, Y.

1994-10-01

The first probe measurements of edge turbulence and transport in a neutral beam induced high confinement mode (H-mode) are reported. A strong negative radial electric field is directly observed in H-mode. A transient suppression of normalized ion saturation and floating potential fluctuation levels occurs at the low confinement mode to high confinement mode (L-H) transition, followed by a recovery to near low mode (L-mode) levels. The average poloidal wave number and the poloidal wave-number spectral width are decreased, and the correlation between fluctuating density and potential is reduced. A large-amplitude coherent oscillation, localized to the strong radial electric field region, is observed in H-mode but does not cause transport. In H-mode the effective turbulent diffusion coefficient is reduced by an order of magnitude inside the last closed flux surface and in the scrape-off layer. The results are compared with a heuristic model of turbulence suppression by velocity-shear stabilization.

Density limit studies on DIII-D

International Nuclear Information System (INIS)

Maingi, R.; Mahdavi, M.A.; Petrie, T.W.

1998-08-01

The authors have studied the processes limiting plasma density and successfully achieved discharges with density ∼50% above the empirical Greenwald density limit with H-mode confinement. This was accomplished by density profile control, enabled through pellet injection and divertor pumping. By examining carefully the criterion for MARFE formation, the authors have derived an edge density limit with scaling very similar to Greenwald scaling. Finally, they have looked in detail at the first and most common density limit process in DIII-D, total divertor detachment, and found that the local upstream separatrix density (n e sep,det ) at detachment onset (partial detachment) increases with the scrape-off layer heating power, P heat , i.e., n e sep,det ∼ P heat 0.76 . This is in marked contrast to the line-average density at detachment which is insensitive to the heating power. The data are in reasonable agreement with the Borass model, which predicted that the upstream density at detachment would increase as P heat 0.7

ELM elimination with Li powder injection in EAST discharges using the tungsten upper divertor

Science.gov (United States)

Maingi, R.; Hu, J. S.; Sun, Z.; Tritz, K.; Zuo, G. Z.; Xu, W.; Huang, M.; Meng, X. C.; Canik, J. M.; Diallo, A.; Lunsford, R.; Mansfield, D. K.; Osborne, T. H.; Gong, X. Z.; Wang, Y. F.; Li, Y. Y.; EAST Team

2018-02-01

We report the first successful use of lithium (Li) to eliminate edge-localized modes (ELMs) with tungsten divertor plasma-facing components in the EAST device. Li powder injected into the scrape-off layer of the tungsten upper divertor successfully eliminated ELMs for 3-5 s in EAST. The ELM elimination became progressively more effective in consecutive discharges at constant lithium delivery rates, and the divertor D α baseline emission was reduced, both signatures of improved wall conditioning. A modest decrease in stored energy and normalized energy confinement was also observed, but the confinement relative to H98 remained well above 1, extending the previous ELM elimination results via Li injection into the lower carbon divertor in EAST (Hu et al 2015 Phys. Rev. Lett. 114 055001). These results can be compared with recent observations with lithium pellets in ASDEX-Upgrade that failed to mitigate ELMs (Lang et al 2017 Nucl. Fusion 57 016030), highlighting one comparative advantage of continuous powder injection for real-time ELM elimination.

Local density of states and order parameter configurations in layered ferromagnet-superconductor structures

Energy Technology Data Exchange (ETDEWEB)

Halterman, Klaus [Physics and Computational Sciences, Research and Engineering Sciences Department, Naval Air Warfare Center, China Lake, CA 93555 (United States)]. E-mail: klaus.halterman@navy.mil; Valls, Oriol T. [School of Physics and Astronomy and Minnesota Supercomputer Institute, University of Minnesota, Minneapolis, MN 55455 (United States)]. E-mail: otvalls@umn.edu

2005-04-01

We analyze the local density of states (LDOS) of heterostructures consisting of alternating ferromagnet, F, and superconductor, S, layers. We consider structures of the SFS and SFSFSFS type, with thin nanometer scale F and S layers, within the ballistic regime. The spin-splitting effects of the ferromagnet and the mutual coupling between the S regions, yield several nontrivial stable and metastable pair amplitude configurations, and we find that the details of the spatial behavior of the pair amplitude govern the calculated electronic spectra. These are reflected in discernible signatures of the LDOS. The roles that the magnetic exchange energy, interface scattering strength, and the Fermi wavevector mismatch each have on the LDOS for the different allowed junction configurations, are systematically investigated.

Local density of states and order parameter configurations in layered ferromagnet-superconductor structures

International Nuclear Information System (INIS)

Halterman, Klaus; Valls, Oriol T.

2005-01-01

We analyze the local density of states (LDOS) of heterostructures consisting of alternating ferromagnet, F, and superconductor, S, layers. We consider structures of the SFS and SFSFSFS type, with thin nanometer scale F and S layers, within the ballistic regime. The spin-splitting effects of the ferromagnet and the mutual coupling between the S regions, yield several nontrivial stable and metastable pair amplitude configurations, and we find that the details of the spatial behavior of the pair amplitude govern the calculated electronic spectra. These are reflected in discernible signatures of the LDOS. The roles that the magnetic exchange energy, interface scattering strength, and the Fermi wavevector mismatch each have on the LDOS for the different allowed junction configurations, are systematically investigated

RCrawler: An R package for parallel web crawling and scraping

Directory of Open Access Journals (Sweden)

Salim Khalil

2017-01-01

Full Text Available RCrawler is a contributed R package for domain-based web crawling and content scraping. As the first implementation of a parallel web crawler in the R environment, RCrawler can crawl, parse, store pages, extract contents, and produce data that can be directly employed for web content mining applications. However, it is also flexible, and could be adapted to other applications. The main features of RCrawler are multi-threaded crawling, content extraction, and duplicate content detection. In addition, it includes functionalities such as URL and content-type filtering, depth level controlling, and a robot.txt parser. Our crawler has a highly optimized system, and can download a large number of pages per second while being robust against certain crashes and spider traps. In this paper, we describe the design and functionality of RCrawler, and report on our experience of implementing it in an R environment, including different optimizations that handle the limitations of R. Finally, we discuss our experimental results.

Isolation and Characterization of an Atypical Metschnikowia sp. Strain from the Skin Scraping of a Dermatitis Patient.

Directory of Open Access Journals (Sweden)

Chee Sian Kuan

Full Text Available A yeast-like organism was isolated from the skin scraping sample of a stasis dermatitis patient in the Mycology Unit Department of Medical Microbiology, University Malaya Medical Centre (UMMC, Kuala Lumpur, Malaysia. The isolate produced no pigment and was not identifiable using chromogenic agar and API 20C AUX. The fungus was identified as Metschnikowia sp. strain UM 1034, which is close to that of Metschnikowia drosophilae based on ITS- and D1/D2 domain-based phylogenetic analysis. However, the physiology of the strain was not associated to M. drosophilae. This pathogen exhibited low sensitivity to all tested azoles, echinocandins, 5-flucytosine and amphotericin B. This study provided insight into Metschnikowia sp. strain UM 1034 phenotype profiles using a Biolog phenotypic microarray (PM. The isolate utilized 373 nutrients of 760 nutrient sources and could adapt to a broad range of osmotic and pH environments. To our knowledge, this is the first report of the isolation of Metschnikowia non-pulcherrima sp. from skin scraping, revealing this rare yeast species as a potential human pathogen that may be misidentified as Candida sp. using conventional methods. Metschnikowia sp. strain UM 1034 can survive in flexible and diverse environments with a generalist lifestyle.

Convective transport in tokamaks

International Nuclear Information System (INIS)

D'Ippolito, D.A.; Myra, J.R.; Russell, D.A.; Krasheninnikov, S.I.; Pigarov, A.Yu.; Yu, G.Q.; Xu, X.Q.; Nevins, W.M.

2005-01-01

Scrape-off-layer (SOL) convection in fusion experiments appears to be a universal phenomenon that can 'short-circuit' the divertor in some cases. The theory of 'blob' transport provides a simple and robust physical paradigm for studying convective transport. This paper summarizes recent advances in the theory of blob transport and its comparison with 2D and 3D computer simulations. We also discuss the common physical basis relating radial transport of blobs, pellets, and ELMs and a new blob regime that may lead to a connection between blob transport and the density limit. (author)

ITER CTA newsletter. No. 16, January 2003

International Nuclear Information System (INIS)

2003-04-01

This ITER CTA newsletter contains information about some ITER related activities including ITER transitional arrangements (ITA) which will start on 1 January 2003, the USA rejoining ITER and People's Republic of China joining ITER, the visit of Mr. J. Koizumi, Prime Minister of Japan, to Kurchatov Institute, Moscow, Russian Federation on 11 January 2003, and the most recent meeting of the Scrape-Off Layer (SOL) and Divertor Physics Group of the International Tokamak Physics Activity (ITPA), which was held in Lausanne, Switzerland, on October 21-23, 2002 at the CRPP/EFL laboratory

Ion transport in turbulent edge plasmas

International Nuclear Information System (INIS)

Helander, P.; Massachusetts Inst. of Tech., Cambridge, MA; Hazeltine, R.D.; Catto, P.J.

1996-02-01

Edge plasmas, such as the tokamak scrape-off layer, exist as a consequence of a balance between cross-field diffusion and parallel losses. The former is usually anomalous, and is widely thought to be driven by strong electrostatic turbulence. It is shown that the anomalous diffusion affects the parallel ion transport by giving rise to a new type of thermal force between different ion species. This force is parallel to the magnetic field, but arises entirely because of perpendicular gradients, and could be important for impurity retention in the tokamak divertor. (author)

Investigation of radial propagation of electrostatic fluctuations in the IR-T1 tokamak plasma edge

Energy Technology Data Exchange (ETDEWEB)

Shariatzadeh, R; Ghoranneviss, M; Salem, M K [Plasma Physics Research Center, Science and Research Branch, Islamic Azad University (IAU), PO Box 14665-678, Tehran (Iran, Islamic Republic of); Emami, M, E-mail: rezashariatzadeh@gmail.com [Laser and Optics Research School, NSTRI, AEOI, PO Box 14155-1339, Tehran (Iran, Islamic Republic of)

2011-01-15

The radial propagation of electrostatic fluctuation is considered extremely important for understanding cross-field anomalous transport. In this paper, two arrays of Langmuir probes are used to analyze electrostatic fluctuations in the edge of IR-T1 tokamak plasma in both the radial and the poloidal directions. The propagation characteristics of the floating potential fluctuations are analyzed by the two-point correlation technique. The wavenumber spectrum shows that there is a net radially outward propagation of turbulent fluctuations in the edge and scrape-off layer (SOL) regions. Hence, edge turbulence presumably originates from core fluctuations.

Collisionality dependent transport in TCV SOL plasmas

DEFF Research Database (Denmark)

Garcia, Odd Erik; Pitts, R.A.; Horacek, J.

2007-01-01

Results are presented from probe measurements in the low field side scrape-off layer (SOL) region of TCV during plasma current scan experiments. It is shown that with decreasing plasma current the radial particle density profile becomes broader and the fluctuation levels and turbulence driven...... radial particle flux increase. In the far SOL the fluctuations exhibit a high degree of statistical similarity and the particle density and flux at the wall radius scale inversely with the plasma current. Together with previous TCV density scan experiments, this indicates that plasma fluctuations...

Monte-Carlo Impurity transport simulations in the edge of the DIII-D tokamak using the MCI code

International Nuclear Information System (INIS)

Evans, T.E.; Mahdavi, M.A.; Sager, G.T.; West, W.P.; Fenstermacher, M.E.; Meyer, W.H.; Porter, G.D.

1995-07-01

A Monte-Carlo Impurity (MCI) transport code is used to follow trace impurities through multiple ionization states in realistic 2-D tokamak geometries. The MCI code is used to study impurity transport along the open magnetic field lines of the Scrape-off Layer (SOL) and to understand how impurities get into the core from the SOL. An MCI study concentrating on the entrainment of carbon impurities ions by deuterium background plasma into the DIII-D divertor is discussed. MCI simulation results are compared to experimental DIII-D carbon measurements

Transition to ELM-free Improved H-mode by Lithium Deposition on NSTX Graphite Divertor Surfaces

International Nuclear Information System (INIS)

Mansfield, D.K.; Kugel, H.W.; Maingi, R.; Bell, M.G.; Bell, R.; Kaita, R.; Kallman, J.; Kaye, S.; LeBlanc, B.; Mueller, D.; Paul, S.; Raman, R.; Roquemore, L.; Sabbagh, S.; Schneider, H.; Skinner, C.H.; Soukhanovskii, V.; Timberlake, J.; Wilgen, J.; Zakharov, L.

2009-01-01

Lithium evaporated onto plasma facing components in the NSTX lower divertor has made dramatic improvements in discharge performance. As lithium accumulated, plasmas previously exhibiting robust Type 1 ELMs gradually transformed into discharges with intermittent ELMs and finally into continuously evolving ELM-free discharges. During this sequence, other discharge parameters changed in a complicated manner. As the ELMs disappeared, energy confinement improved and remarkable changes in edge and scrape-off layer plasma properties were observed. These results demonstrate that active modification of plasma surface interactions can preempt large ELMs.

Numerical simulations of blobs with ion dynamics

DEFF Research Database (Denmark)

Nielsen, Anders Henry; Rasmussen, Jens Juul; Madsen, Jens

2017-01-01

The transport of particles and energy into the scrape-off layer (SOL) region at the outboard midplane of medium-sized tokamaks, operating in low confinement mode, is investigated by applying the first-principle HESEL (hot edge-sol-electrostatic) model. HESEL is a four-field drift-fluid model...... of a 'shoulder' in the SOL density profile can be obtained by increasing the collisionality or connection length, thus decreasing the efficiency of the SOL's ability to remove plasma. As the ion pressure has a larger perpendicular but smaller parallel dissipation rate compared to the electron pressure, ion...

Elastic–plastic adhesive impacts of tungsten dust with metal surfaces in plasma environments

Energy Technology Data Exchange (ETDEWEB)

Ratynskaia, S., E-mail: svetlana.ratynskaia@ee.kth.se [KTH Royal Institute of Technology, Association EUROfusion-VR, Stockholm (Sweden); Tolias, P. [KTH Royal Institute of Technology, Association EUROfusion-VR, Stockholm (Sweden); Shalpegin, A. [Université de Lorraine, Institut Jean Lamour, Vandoeuvre-lès-Nancy (France); Vignitchouk, L. [KTH Royal Institute of Technology, Association EUROfusion-VR, Stockholm (Sweden); De Angeli, M. [Istituto di Fisica del Plasma – Consiglio Nazionale delle Ricerche, Milan (Italy); Bykov, I. [KTH Royal Institute of Technology, Association EUROfusion-VR, Stockholm (Sweden); Bystrov, K.; Bardin, S. [FOM Institute DIFFER, Dutch Institute For Fundamental Energy Research, Edisonbaan 14, 3439MN Nieuwegein (Netherlands); Brochard, F. [Université de Lorraine, Institut Jean Lamour, Vandoeuvre-lès-Nancy (France); Ripamonti, D. [Istituto per l’Energetica e le Interfasi – Consiglio Nazionale delle Ricerche, Milan (Italy); Harder, N. den; De Temmerman, G. [FOM Institute DIFFER, Dutch Institute For Fundamental Energy Research, Edisonbaan 14, 3439MN Nieuwegein (Netherlands)

2015-08-15

Dust-surface collisions impose size selectivity on the ability of dust grains to migrate in scrape-off layer and divertor plasmas and to adhere to plasma-facing components. Here, we report first experimental evidence of dust impact phenomena in plasma environments concerning low-speed collisions of tungsten dust with tungsten surfaces: re-bouncing, adhesion, sliding and rolling. The results comply with the predictions of the model of elastic-perfectly plastic adhesive spheres employed in the dust dynamics code MIGRAINe for sub- to several meters per second impacts of micrometer-range metal dust.

Investigation of radial propagation of electrostatic fluctuations in the IR-T1 tokamak plasma edge

International Nuclear Information System (INIS)

Shariatzadeh, R; Ghoranneviss, M; Salem, M K; Emami, M

2011-01-01

The radial propagation of electrostatic fluctuation is considered extremely important for understanding cross-field anomalous transport. In this paper, two arrays of Langmuir probes are used to analyze electrostatic fluctuations in the edge of IR-T1 tokamak plasma in both the radial and the poloidal directions. The propagation characteristics of the floating potential fluctuations are analyzed by the two-point correlation technique. The wavenumber spectrum shows that there is a net radially outward propagation of turbulent fluctuations in the edge and scrape-off layer (SOL) regions. Hence, edge turbulence presumably originates from core fluctuations.

Monte-Carlo Impurity transport simulations in the edge of the DIII-D tokamak using the MCI code

International Nuclear Information System (INIS)

Evans, T.E.; Sager, G.T.; Mahdavi, M.A.; Porter, G.D.; Fenstermacher, M.E.; Meyer, W.H.

1995-01-01

A Monte-Carlo Impurity (MCI) transport code is used to follow trace impurities through multiple ionization states in realistic 2-D tokamak geometries. The MCI code is used to study impurity transport along the open magnetic field lines of the Scrape-off Layer (SOL) and to understand how impurities get into the core from the SOL. An MCI study concentrating on the entrainment of carbon impurities ions by deuterium background plasma into the DII-D divertor is discussed. MCI simulation results are compared to experimental DII-D carbon measurements. 2 refs

An analytic model for flow reversal in divertor plasmas

International Nuclear Information System (INIS)

Cooke, P.I.H.; Prinja, A.K.

1987-04-01

An analytic model is developed and used to study the phenomenon of flow reversal which is observed in two-dimensional simulations of divertor plasmas. The effect is shown to be caused by the radial spread of neutral particles emitted from the divertor target which can lead to a strong peaking of the ionization source at certain radial locations. The results indicate that flow reversal over a portion of the width of the scrape-off layer is inevitable in high recycling conditions. Implications for impurity transport and particle removal in reactors are discussed

Plasma boundary phenomena in tokamaks

International Nuclear Information System (INIS)

Stangeby, P.C.

1989-06-01

The focus of this review is on processes occurring at the edge, and on the connection between boundary plasma - the scrape-off layer (SOL) and the radiating layer - and central plasma processes. Techniques used for edge diagnosis are reviewed and basic experimental information (n e and T e ) is summarized. Simple models of the SOL are summarized, and the most important effects of the boundary plasma - the influence on the fuel particles, impurities, and energy - on tokamak operation dealt with. Methods of manipulating and controlling edge conditions in tokamaks and the experimental data base for the edge during auxiliary heating of tokamaks are reviewed. Fluctuations and asymmetries at the edge are also covered. (9 tabs., 134 figs., 879 refs.)

Effect of ICRH on the JET edge plasma with carbon and beryllium coated limiters

International Nuclear Information System (INIS)

Clement, S.; Erents, S.K.; Tagle, J.A.; Brinkschulte, H.; Bures, M.; De Kock, L.

1990-01-01

Investigation of the scrape-off Layer (SOL) at different poloidal positions has been carried out with Langmuir probes for limiter discharges with ion cyclotron resonance heating (ICRH) at JET. A comparison of the effects of ICRH on the edge is presented for operation with all carbon limiters, and for operation with a beryllium layer evaporated on the walls and limiters of JET. The behaviour of the SOL parameters is similar for both cases, although edge temperatures tend to be lower in the Be case. Measurements with probes between the belt limiters and close to the ICRH antennas show that the edge parameters in this region are strongly influenced by the vicinity of an active antenna. (orig.)

Resistive switching memory properties of layer-by-layer assembled enzyme multilayers

International Nuclear Information System (INIS)

Baek, Hyunhee; Cho, Jinhan; Lee, Chanwoo; Lim, Kwang-il

2012-01-01

The properties of enzymes, which can cause reversible changes in currents through redox reactions in solution, are of fundamental and practical importance in bio-electrochemical applications. These redox properties of enzymes are often associated with their charge-trap sites. Here, we demonstrate that reversible changes in resistance in dried lysozyme (LYS) films can be generated by an externally applied voltage as a result of charge trap/release. Based on such changes, LYS can be used as resistive switching active material for nonvolatile memory devices. In this study, cationic LYS and anionic poly(styrene sulfonate) (PSS) layers were alternately deposited onto Pt-coated silicon substrates using a layer-by-layer assembly method. Then, top electrodes were deposited onto the top of LYS/PSS multilayers to complete the fabrication of the memory-like device. The LYS/PSS multilayer devices exhibited typical resistive switching characteristics with an ON/OFF current ratio above 10 2 , a fast switching speed of 100 ns and stable performance. Furthermore, the insertion of insulating polyelectrolytes (PEs) between the respective LYS layers significantly enhanced the memory performance of the devices showing a high ON/OFF current ratio of ∼10 6 and low levels of power consumption. (paper)

A trade-off between local and distributed information processing associated with remote episodic versus semantic memory.

Science.gov (United States)

Heisz, Jennifer J; Vakorin, Vasily; Ross, Bernhard; Levine, Brian; McIntosh, Anthony R

2014-01-01

Episodic memory and semantic memory produce very different subjective experiences yet rely on overlapping networks of brain regions for processing. Traditional approaches for characterizing functional brain networks emphasize static states of function and thus are blind to the dynamic information processing within and across brain regions. This study used information theoretic measures of entropy to quantify changes in the complexity of the brain's response as measured by magnetoencephalography while participants listened to audio recordings describing past personal episodic and general semantic events. Personal episodic recordings evoked richer subjective mnemonic experiences and more complex brain responses than general semantic recordings. Critically, we observed a trade-off between the relative contribution of local versus distributed entropy, such that personal episodic recordings produced relatively more local entropy whereas general semantic recordings produced relatively more distributed entropy. Changes in the relative contributions of local and distributed entropy to the total complexity of the system provides a potential mechanism that allows the same network of brain regions to represent cognitive information as either specific episodes or more general semantic knowledge.

Reduction of buffer layer conduction near plasma-assisted molecular-beam epitaxy grown GaN/AlN interfaces by beryllium doping

International Nuclear Information System (INIS)

Storm, D.F.; Katzer, D.S.; Binari, S.C.; Glaser, E.R.; Shanabrook, B.V.; Roussos, J.A.

2002-01-01

Beryllium doping of epitaxial GaN layers is used to reduce leakage currents through interfacial or buffer conducting layers grown by plasma-assisted molecular-beam epitaxy on SiC. Capacitance-voltage measurements of Schottky barrier test structures and dc pinch-off characteristics of unintentionally doped GaN high-electron-mobility transistors indicate that these leakage currents are localized near the GaN/AlN interface of our AlGaN/GaN/AlN device structures. Insertion of a 2000 Aa Be:GaN layer at the interface reduces these currents by three orders of magnitude

Layer-by-layer assembled TiO{sub 2} films with high ultraviolet light-shielding property

Energy Technology Data Exchange (ETDEWEB)

Li, Xiaozhou [College of Science, Northwest A and F University, Yangling, Shaanxi 712100 (China); Wang, Lin, E-mail: wanglin0317@nwsuaf.edu.cn [College of Science, Northwest A and F University, Yangling, Shaanxi 712100 (China); Pei, Yuxin [College of Science, Northwest A and F University, Yangling, Shaanxi 712100 (China); Jiang, Jinqiang [State Key Lab of Applied Surface and Colloid Chemistry, College of Chemistry and Chemical Engineering, Shaanxi Normal University, Xi' an 710062 (China)

2014-11-28

Ultraviolet (UV) B is hazardous to human, plants and animals. With the rapid growth of ozone holes over the earth, the exploration of optical materials that can cut off harmful UV radiation is important. In this work, fusiform TiO{sub 2} nanoparticles were synthesized by a hydrothermal synthesis method. The thin films assembled with TiO{sub 2} nanoparticles and oppositely charged polyelectrolytes were fabricated via a layer-by-layer assembly method. The fabrication of poly(ethylene imine) (PEI)/TiO{sub 2} multilayer films was verified by ultraviolet–visible spectra measurements, scanning electron microscopy and atomic force microscopy. The as-prepared PEI/TiO{sub 2} multilayer films can effectively absorb harmful UVB light and filter off visible light. Most importantly, the PEI/TiO{sub 2} films can be deposited directly on various kinds of hydrophilic substrates such as quartz, glass, silicon and hydrophobic substrates such as polystyrene, polypropylene, polyethylene and polymethyl methacrylate when the hydrophilic substrates were modified to obtain a hydrophilic surface. - Highlights: • PEI/TiO{sub 2} films were fabricated via a layer-by-layer self-assembly method. • The films could effectively absorb harmful UVB light and filter off visible light. • The films could deposit directly on either hydrophilic or hydrophobic substrates.

Control of a shock wave-boundary layer interaction using localized arc filament plasma actuators

Science.gov (United States)

Webb, Nathan Joseph

Supersonic flight is currently possible, but expensive. Inexpensive supersonic travel will require increased efficiency of high-speed air entrainment, an integral part of air-breathing propulsion systems. Although mixed compression inlet geometry can significantly improve entrainment efficiency, numerous Shock Wave-Boundary Layer Interactions (SWBLIs) are generated in this configuration. The boundary layer must therefore develop through multiple regions of adverse pressure gradient, causing it to thicken, and, in severe cases, separate. The associated increase in unsteadiness can have adverse effects on downstream engine hardware. The most severe consequence of these interactions is the increased aerodynamic blockage generated by the thickened boundary layer. If the increase is sufficient, it can choke the flow, causing inlet unstart, and resulting in a loss of thrust and high transient forces on the engine, airframe, and aircraft occupants. The potentially severe consequences associated with SWBLIs require flow control to ensure proper operation. Traditionally, boundary layer bleed has been used to control the interaction. Although this method is effective, it has inherent efficiency penalties. Localized Arc Filament Plasma Actuators (LAFPAs) are designed to generate perturbations for flow control. Natural flow instabilities act to amplify certain perturbations, allowing the LAFPAs to control the flow with minimal power input. LAFPAs also have the flexibility to maintain control over a variety of operating conditions. This work seeks to examine the effectiveness of LAFPAs as a separation control method for an oblique, impinging SWBLI. The low frequency unsteadiness in the reflected shock was thought to be the natural manifestation of a Kelvin-Helmholtz instability in the shear layer above the separation region. The LAFPAs were therefore placed upstream of the interaction to allow their perturbations to convect to the receptivity region (near the shear layer origin

Low-cost fabrication and polar-dependent switching uniformity of memory devices using alumina interfacial layer and Ag nanoparticle monolayer

Directory of Open Access Journals (Sweden)

Peng Xia

2017-11-01

Full Text Available A facile and low-cost process was developed for fabricating write-once-read-many-times (WORM Cu/Ag NPs/Alumina/Al memory devices, where the alumina passivation layer formed naturally in air at room temperature, whereas the Ag nanoparticle monolayer was in situ prepared through thermal annealing of a 4.5 nm Ag film in air at 150°C. The devices exhibit irreversible transition from initial high resistance (OFF state to low resistance (ON state, with ON/OFF ratio of 107, indicating the introduction of Ag nanoparticle monolayer greatly improves ON/OFF ratio by four orders of magnitude. The uniformity of threshold voltages exhibits a polar-dependent behavior, and a narrow range of threshold voltages of 0.40 V among individual devices was achieved upon the forward voltage. The memory device can be regarded as two switching units connected in series. The uniform alumina interfacial layer and the non-uniform distribution of local electric fields originated from Ag nanoparticles might be responsible for excellent switching uniformity. Since silver ions in active layer can act as fast ion conductor, a plausible mechanism relating to the formation of filaments sequentially among the two switching units connected in series is suggested for the polar-dependent switching behavior. Furthermore, we demonstrate both alumina layer and Ag NPs monolayer play essential roles in improving switching parameters based on comparative experiments.

Low-cost fabrication and polar-dependent switching uniformity of memory devices using alumina interfacial layer and Ag nanoparticle monolayer

Science.gov (United States)

Xia, Peng; Li, Luman; Wang, Pengfei; Gan, Ying; Xu, Wei

2017-11-01

A facile and low-cost process was developed for fabricating write-once-read-many-times (WORM) Cu/Ag NPs/Alumina/Al memory devices, where the alumina passivation layer formed naturally in air at room temperature, whereas the Ag nanoparticle monolayer was in situ prepared through thermal annealing of a 4.5 nm Ag film in air at 150°C. The devices exhibit irreversible transition from initial high resistance (OFF) state to low resistance (ON) state, with ON/OFF ratio of 107, indicating the introduction of Ag nanoparticle monolayer greatly improves ON/OFF ratio by four orders of magnitude. The uniformity of threshold voltages exhibits a polar-dependent behavior, and a narrow range of threshold voltages of 0.40 V among individual devices was achieved upon the forward voltage. The memory device can be regarded as two switching units connected in series. The uniform alumina interfacial layer and the non-uniform distribution of local electric fields originated from Ag nanoparticles might be responsible for excellent switching uniformity. Since silver ions in active layer can act as fast ion conductor, a plausible mechanism relating to the formation of filaments sequentially among the two switching units connected in series is suggested for the polar-dependent switching behavior. Furthermore, we demonstrate both alumina layer and Ag NPs monolayer play essential roles in improving switching parameters based on comparative experiments.

CHANGES IN EDGE AND SCRAPE-OFF LAYER PLASMA BEHAVIOE DUE TO VAARIATION IN MAGNETIC BALANCE IN DIII-D

International Nuclear Information System (INIS)

PETRIE, T.W.; WATKINS, J.G.; BAYLOR, L.R.; BROOKS, N.H.; FENSTERMACHER, M.E.; HYATT, A.W.; JACKSON, G.L.; LASNIER, C.J.; LEONARD, A.W.; PIGAROV, A.YU.; RENSINK, M.E.; ROGNLIEN, T.D.; SCHAFFER, M.J.; WOLF, N.S.

2002-01-01

Changes in the divertor magnetic balance in DIII-D H-mode plasmas affects core, edge, and divertor plasma behavior. Both the pedestal density n e,PED and plasma stored energy W T were sensitive to changes in magnetic balance near the double-null (DN) configuration, e.g., both decreased 20%-30% when the DN shifted to a slightly unbalanced DN, where the B x (del)B drift direction pointed away from the main X-point. Recycling at each of the four divertor targets was sensitive to changes in magnetic balance and the B x (del)B drift direction. The poloidal distribution of the recycling in DN is in qualitative agreement with the predictions of UEDGE modeling with particle drifts included. The particle flux at the inner divertor target is shown to be much more sensitive to magnetic balance than the particle flux at the outer divertor target near the DN shape. These results suggest possible advantages and drawbacks for balanced DN operation

[Segmental cut-off bridge and local floating technology for the treatment of ossification of ligamentum flavum in thoracic spine].

Science.gov (United States)

Liang, Wei-dong; Zhang, Jian; Sheng, Wei-bin

2013-10-08

To explore the efficacy and safety of segmental cut-off bridge and local floating technology for the treatment of ossification of ligamentum flavum (OLF) in thoracic spine. Retrospective study was performed in 98 patients with thoracic OLF who under went operation. There was 56 males and 42 females with an average age of 45.8 (35-73) years. The average duration of onset was 17 (3-51) months. The main clinical symptoms were numbness and paraesthesia (n = 90), lower limb weakness and walking trouble (n = 46), positive pyramidal tract signs (n = 33) and sphincter function obstacle (n = 9). OLF was screened and diagnosed by radiology, magnetic resonance imaging (MRI), computed tomography (CT) or CT myelography (CTM). A total of 142 OLF nidus were spotted. The lesions involved single segment (n = 32), double segments (n = 56), three segments (n = 6) and ≥ four segments (n = 4). And the locations were at upper thoracic segment (T1-4) (n = 34), middle thoracic segment (T5-8) (n = 23) and lower thoracic segment (T9-12) (n = 42). The OLF nidus were removed by local floating technology oft windowing at cephalic and caudal ends and a cut-off bridge at both sides of involved segments. Pre- and post-operative Japanese Orthopedic Association (JOA) scores and Epstein grades were recorded to evaluate the outcomes. The mean loss volume of blood was 320 ml and operative duration 155 min. All cases recovered independent activities. The mean follow-up period was 28 (13-48) months. The mean preoperative JOA score was 4.3 (1-8) points and the mean postoperative JOA score 9.7 (5-11) points. The recovery rate was 78.8%. According to Epstein grade, the excellent and good rate was 86.7%. As a common cause of thoracic spinal cord compression, OLF should be operated as early as possible. Based upon clinical and imaging findings, the application of segmental cut-off bridge and local floating technology is both safe and efficacious in the treatment of OLF in thoracic spine.