WorldWideScience

Sample records for local hydrogen production

  1. In Situ Measurement of Local Hydrogen Production Rate by Bubble-Evolved Recording

    Directory of Open Access Journals (Sweden)

    Xiaowei Hu

    2013-01-01

    Full Text Available Hydrogen visibly bubbles during photocatalytic water splitting under illumination with above-bandgap radiation, which provides a direct measurement of local gas-evolving reaction rate. In this paper, optical microscopy of superfield depth was used for recording the hydrogen bubble growth on Cd0.5Zn0.5S photocatalyst in reaction liquid and illuminated with purple light. By analyzing change of hydrogen bubble size as a function of time, we understood that hydrogen bubble growth experienced two periods, which were inertia effect dominated period and diffusion effect dominated period, respectively. The tendency of hydrogen bubble growth was similar to that of the gas bubble in boiling, while the difference in bubble diameter and growth time magnitude was great. Meanwhile, we obtained the local hydrogen production rate on photocatalyst active site by measuring hydrogen bubble growth variation characteristics. This method makes it possible to confirm local actual hydrogen evolution rate quantitatively during photocatalytic water splitting.

  2. Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    None

    2014-09-01

    This 2-page fact sheet provides a brief introduction to hydrogen production technologies. Intended for a non-technical audience, it explains how different resources and processes can be used to produce hydrogen. It includes an overview of research goals as well as “quick facts” about hydrogen energy resources and production technologies.

  3. In Situ Measurement of Local Hydrogen Production Rate by Bubble-Evolved Recording

    OpenAIRE

    Xiaowei Hu; Liejin Guo; Yechun Wang

    2013-01-01

    Hydrogen visibly bubbles during photocatalytic water splitting under illumination with above-bandgap radiation, which provides a direct measurement of local gas-evolving reaction rate. In this paper, optical microscopy of superfield depth was used for recording the hydrogen bubble growth on Cd0.5Zn0.5S photocatalyst in reaction liquid and illuminated with purple light. By analyzing change of hydrogen bubble size as a function of time, we understood that hydrogen bubble growth experienced two ...

  4. Hydrogen production by Cyanobacteria

    Directory of Open Access Journals (Sweden)

    Chaudhuri Surabhi

    2005-12-01

    Full Text Available Abstract The limited fossil fuel prompts the prospecting of various unconventional energy sources to take over the traditional fossil fuel energy source. In this respect the use of hydrogen gas is an attractive alternate source. Attributed by its numerous advantages including those of environmentally clean, efficiency and renew ability, hydrogen gas is considered to be one of the most desired alternate. Cyanobacteria are highly promising microorganism for hydrogen production. In comparison to the traditional ways of hydrogen production (chemical, photoelectrical, Cyanobacterial hydrogen production is commercially viable. This review highlights the basic biology of cynobacterial hydrogen production, strains involved, large-scale hydrogen production and its future prospects. While integrating the existing knowledge and technology, much future improvement and progress is to be done before hydrogen is accepted as a commercial primary energy source.

  5. Photobiological hydrogen production.

    Science.gov (United States)

    Asada, Y; Miyake, J

    1999-01-01

    The principles and recent progress in the research and development of photobiological hydrogen production are reviewed. Cyanobacteria produce hydrogen gas using nitrogenase and/or hydrogenase. Hydrogen production mediated by native hydrogenases in cyanobacteria occurs under in the dark under anaerobic conditions by degradation of intracellular glycogen. In vitro and in vivo coupling of the cyanobacterial photosynthetic system with a clostridial hydrogenase via cyanobacterial ferredoxin was demonstrated in the presence of light. Genetic transformation of Synechococcus PCC7942 with the hydrogenase gene from Clostridium pasteurianum was successful; the active enzyme was expressed in PCC7942. The strong hydrogen producers among photosynthetic bacteria were isolated and characterized. Coculture of Rhodobacter and Clostriudium was applied for hydrogen production from glucose. A mutant strain of Rhodobacter sphaeroides RV whose light-harvesting proteins were altered was obtained by UV irradiation. Hydrogen productivity by the mutant was improved when irradiated with monochromatic light of some wavelengths. The development of photobioreactors for hydrogen production is also reviewed.

  6. Biological hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Benemann, J.R. [Univ. of California, Berkeley, CA (United States)

    1995-11-01

    Biological hydrogen production can be accomplished by either thermochemical (gasification) conversion of woody biomass and agricultural residues or by microbiological processes that yield hydrogen gas from organic wastes or water. Biomass gasification is a well established technology; however, the synthesis gas produced, a mixture of CO and H{sub 2}, requires a shift reaction to convert the CO to H{sub 2}. Microbiological processes can carry out this reaction more efficiently than conventional catalysts, and may be more appropriate for the relatively small-scale of biomass gasification processes. Development of a microbial shift reaction may be a near-term practical application of microbial hydrogen production.

  7. Photoelectrochemical hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Rocheleau, R.; Misra, A.; Miller, E. [Univ. of Hawaii, Honolulu, HI (United States)

    1998-08-01

    A significant component of the US DOE Hydrogen Program is the development of a practical technology for the direct production of hydrogen using a renewable source of energy. High efficiency photoelectrochemical systems to produce hydrogen directly from water using sunlight as the energy source represent one of the technologies identified by DOE to meet this mission. Reactor modeling and experiments conducted at UH provide strong evidence that direct solar-to-hydrogen conversion efficiency greater than 10% can be expected using photoelectrodes fabricated from low-cost, multijunction (MJ) amorphous silicon solar cells. Solar-to-hydrogen conversion efficiencies as high as 7.8% have been achieved using a 10.3% efficient MJ amorphous silicon solar cell. Higher efficiency can be expected with the use of higher efficiency solar cells, further improvement of the thin film oxidation and reduction catalysts, and optimization of the solar cell for hydrogen production rather than electricity production. Hydrogen and oxygen catalysts developed under this project are very stable, exhibiting no measurable degradation in KOH after over 13,000 hours of operation. Additional research is needed to fully optimize the transparent, conducting coatings which will be needed for large area integrated arrays. To date, the best protection has been afforded by wide bandgap amorphous silicon carbide films.

  8. Biomimetic hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Krassen, Henning

    2009-05-15

    Hydrogenases catalyze the reduction of protons to molecular hydrogen with outstanding efficiency. An electrode surface which is covered with active hydrogenase molecules becomes a promising alternative to platinum for electrochemical hydrogen production. To immobilize the hydrogenase on the electrode, the gold surface was modified by heterobifunctional molecules. A thiol headgroup on one side allowed the binding to the gold surface and the formation of a self-assembled monolayer. The other side of the molecules provided a surface with a high affinity for the hydrogenase CrHydA1 from Chlamydomonas reinhardtii. With methylviologen as a soluble energy carrier, electrons were transferred from carboxy-terminated electrodes to CrHydA1 and conducted to the active site (H-cluster), where they reduce protons to molecular hydrogen. A combined approach of surface-enhanced infrared absorption spectroscopy, gas chromatography, and surface plasmon resonance allowed quantifying the hydrogen production on a molecular level. Hydrogen was produced with a rate of 85 mol H{sub 2} min{sup -1} mol{sup -1}. On a 1'- benzyl-4,4'-bipyridinum (BBP)-terminated surface, the electrons were mediated by the monolayer and no soluble electron carrier was necessary to achieve a comparable hydrogen production rate (approximately 50% of the former system). The hydrogen evolution potential was determined to be -335 mV for the BBP-bound hydrogenase and -290 mV for the hydrogenase which was immobilized on a carboxy-terminated mercaptopropionic acid SAM. Therefore, both systems significantly reduce the hydrogen production overpotential and allow electrochemical hydrogen production at an energy level which is close to the commercially applied platinum electrodes (hydrogen evolution potential of -270 mV). In order to couple hydrogen production and photosynthesis, photosystem I (PS1) from Synechocystis PCC 6803 and membrane-bound hydrogenase (MBH) from Ralstonia eutropha were bound to each other

  9. Photoelectrochemical hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Rocheleau, R.E.; Miller, E.; Misra, A. [Univ. of Hawaii, Honolulu, HI (United States)

    1996-10-01

    The large-scale production of hydrogen utilizing energy provided by a renewable source to split water is one of the most ambitious long-term goals of the U.S. Department of Energy`s Hydrogen Program. One promising option to meet this goal is direct photoelectrolysis in which light absorbed by semiconductor-based photoelectrodes produces electrical power internally to split water into hydrogen and oxygen. Under this program, direct solar-to-chemical conversion efficiencies as high as 7.8 % have been demonstrated using low-cost, amorphous-silicon-based photoelectrodes. Detailed loss analysis models indicate that solar-to-chemical conversion greater than 10% can be achieved with amorphous-silicon-based structures optimized for hydrogen production. In this report, the authors describe the continuing progress in the development of thin-film catalytic/protective coatings, results of outdoor testing, and efforts to develop high efficiency, stable prototype systems.

  10. Sustainable Electrochemical Hydrogen Production

    DEFF Research Database (Denmark)

    Kibsgaard, Jakob; Jaramillo, Thomas F.; Chorkendorff, Ib

    production is through electrochemical processes coupled to renewable energy sources such as wind or solar. The hydrogen evolution reaction (HER, 2H+ + 2e− → H2) constitutes half of the water splitting reaction. To increase process efficiency, active catalysts for the HER are needed. Currently platinum...

  11. Photoelectrochemical Hydrogen Production

    CERN Document Server

    Krol, R van de

    2012-01-01

    Photoelectrochemical Hydrogen Production describes the principles and materials challenges for the conversion of sunlight into hydrogen through water splitting at a semiconducting electrode. Readers will find an analysis of the solid state properties and materials requirements for semiconducting photo-electrodes, a detailed description of the semiconductor/electrolyte interface, in addition to the photo-electrochemical (PEC) cell. Experimental techniques to investigate both materials and PEC device performance are outlined, followed by an overview of the current state-of-the-art in PEC materia

  12. Photovoltaic hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Hiser, H.W.; Memory, S.B.; Veziroglu, T.N.; Padin, J. [Univ. of Miami, Coral Gables, FL (United States)

    1996-10-01

    This is a new project, which started in June 1995, and involves photovoltaic hydrogen production as a fuel production method for the future. In order to increase the hydrogen yield, it was decided to use hybrid solar collectors to generate D.C. electricity, as well as high temperature steam for input to the electrolyzer. In this way, some of the energy needed to dissociate the water is supplied in the form of heat (or low grade energy), to generate steam, which results in a reduction of electrical energy (or high grade energy) needed. As a result, solar to hydrogen conversion efficiency is increased. In the above stated system, the collector location, the collector tracking sub-system (i.e., orientation/rotation), and the steam temperature have been taken as variables. Five locations selected - in order to consider a variety of latitudes, altitudes, cloud coverage and atmospheric conditions - are Atlanta, Denver, Miami, Phoenix and Salt Lake City. Plain PV and hybrid solar collectors for a stationary south facing system and five different collector rotation systems have been analyzed. Steam temperatures have been varied between 200{degrees}C and 1200{degrees}C. During the first year, solar to hydrogen conversion efficiencies have been considered. The results show that higher steam temperatures, 2 dimensional tracking system, higher elevations and dryer climates causes higher conversion efficiencies. Cost effectiveness of the sub-systems and of the overall system will be analyzed during the second year. Also, initial studies will be made of an advanced high efficiency hybrid solar hydrogen production system.

  13. Biomimetic Production of Hydrogen

    Science.gov (United States)

    Gust, Devens

    2004-03-01

    The basic reaction for hydrogen generation is formation of molecular hydrogen from two electrons and two protons. Although there are many possible sources for the protons and electrons, and a variety of mechanisms for providing the requisite energy for hydrogen synthesis, the most abundant and readily available source of protons and electrons is water, and the most attractive source of energy for powering the process is sunlight. Not surprisingly, living systems have evolved to take advantage of these sources for materials and energy. Thus, biology provides paradigms for carrying out the reactions necessary for hydrogen production. Photosynthesis in green plants uses sunlight as the source of energy for the oxidation of water to give molecular oxygen, protons, and reduction potential. Some photosynthetic organisms are capable of using this reduction potential, in the form of the reduced redox protein ferredoxin, to reduce protons and produce molecular hydrogen via the action of an hydrogenase enzyme. A variety of other organisms metabolize the reduced carbon compounds that are ultimately the major products of photosynthesis to produce molecular hydrogen. These facts suggest that it might be possible to use light energy to make molecular hydrogen via biomimetic constructs that employ principles similar to those used by natural organisms, or perhaps with hybrid "bionic" systems that combine biomimetic materials with natural enzymes. It is now possible to construct artificial photosynthetic systems that mimic some of the major steps in the natural process.(1) Artificial antennas based on porphyrins, carotenoids and other chromophores absorb light at various wavelengths in the solar spectrum and transfer the harvested excitation energy to artificial photosynthetic reaction centers.(2) In these centers, photoinduced electron transfer uses the energy from light to move an electron from a donor to an acceptor moiety, generating a high-energy charge-separated state

  14. Waste/By-Product Hydrogen

    Science.gov (United States)

    2011-01-13

    By‐ product Hydrogen Fuel Flexibility Biogas : generated from organic waste �Wastewater treatment plants can provide multiple MW of renewable... Waste /By product Hydrogen Waste H2 sources include: � Waste bio‐mass: biogas to high temp fuel cells to produce H2 – there are over two dozen sites...13 Waste /By product Hydrogen ‐ Biogas

  15. Potentialities of hydrogen production in Algeria

    Energy Technology Data Exchange (ETDEWEB)

    Boudries, R. [CDER, Route de l' Observatoire, Bouzareah Algiers (Algeria); USTHB, El Alia, Algiers (Algeria); Dizene, R. [USTHB, El Alia, Algiers (Algeria)

    2008-09-15

    The objective of the present study is to estimate the potentialities of hydrogen production in Algeria. Particular attention is paid to the clean and sustainable hydrogen production, i.e., production from renewable energy. First, the present overall energy situation in Algeria is reviewed. Trend in energy demand is analysed taking into account major parameters such as population growth, urbanization, improvement in quality of life and export opportunities. The resources available for hydrogen production are then presented. Finally, the estimation of hydrogen production potential using solar sources, the most important renewable energy sources in Algeria, is presented. This study indicates that the shift to hydrogen economy shows a promising prospect. Not only, it can meet the evergrowing local needs but it will also allow Algeria to keep its share of the energy market. Indeed, as is now the case for natural gas, hydrogen could be delivered to Western Europe through pipelines. (author)

  16. Photoelectrochemical hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Rocheleau, R.E.; Miller, E.; Zhang, Z. [Univ. of Hawaii, Honolulu, HI (United States)

    1995-09-01

    The large-scale production of hydrogen utilizing energy provided by a renewable source to split water is one of the most ambitious long-term goals of the U.S. Department of Energy`s Hydrogen Program. Photoelectrochemical devices-direct photoconversion systems utilizing a photovoltaic-type structure coated with water-splitting catalysts-represent a promising option to meet this goal. Direct solar-to-chemical conversion efficiencies greater than 7% and photoelectrode lifetimes of up to 30 hours in 1 molar KOH have been demonstrated in our laboratory using low-cost, amorphous-silicon-based photoelectrodes. Loss analysis models indicate that the DOE`s goal of 10% solar-to-chemical conversion can be met with amorphous-silicon-based structures optimized for hydrogen production. In this report, we describe recent progress in the development of thin-film catalytic/protective coatings, improvements in photoelectrode efficiency and stability, and designs for higher efficiency and greater stability.

  17. Solar hydrogen production: renewable hydrogen production by dry fuel reforming

    Science.gov (United States)

    Bakos, Jamie; Miyamoto, Henry K.

    2006-09-01

    SHEC LABS - Solar Hydrogen Energy Corporation constructed a pilot-plant to demonstrate a Dry Fuel Reforming (DFR) system that is heated primarily by sunlight focusing-mirrors. The pilot-plant consists of: 1) a solar mirror array and solar concentrator and shutter system; and 2) two thermo-catalytic reactors to convert Methane, Carbon Dioxide, and Water into Hydrogen. Results from the pilot study show that solar Hydrogen generation is feasible and cost-competitive with traditional Hydrogen production. More than 95% of Hydrogen commercially produced today is by the Steam Methane Reformation (SMR) of natural gas, a process that liberates Carbon Dioxide to the atmosphere. The SMR process provides a net energy loss of 30 to 35% when converting from Methane to Hydrogen. Solar Hydrogen production provides a 14% net energy gain when converting Methane into Hydrogen since the energy used to drive the process is from the sun. The environmental benefits of generating Hydrogen using renewable energy include significant greenhouse gas and criteria air contaminant reductions.

  18. Fusion Energy for Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Fillo, J. A.; Powell, J. R.; Steinberg, M.; Salzano, F.; Benenati, R.; Dang, V.; Fogelson, S.; Isaacs, H.; Kouts, H.; Kushner, M.; Lazareth, O.; Majeski, S.; Makowitz, H.; Sheehan, T. V.

    1978-09-01

    The decreasing availability of fossil fuels emphasizes the need to develop systems which will produce synthetic fuel to substitute for and supplement the natural supply. An important first step in the synthesis of liquid and gaseous fuels is the production of hydrogen. Thermonuclear fusion offers an inexhaustible source of energy for the production of hydrogen from water. Depending on design, electric generation efficiencies of approximately 40 to 60% and hydrogen production efficiencies by high temperature electrolysis of approximately 50 to 70% are projected for fusion reactors using high temperature blankets.

  19. Hydrogen Production by Thermophilic Fermentation

    NARCIS (Netherlands)

    Niel, van E.W.J.; Willquist, K.; Zeidan, A.A.; Vrije, de T.; Mars, A.E.; Claassen, P.A.M.

    2012-01-01

    Of the many ways hydrogen can be produced, this chapter focuses on biological hydrogen production by thermophilic bacteria and archaea in dark fermentations. The thermophiles are held as promising candidates for a cost-effective fermentation process, because of their relatively high yields and broad

  20. Microalgal hydrogen production - A review.

    Science.gov (United States)

    Khetkorn, Wanthanee; Rastogi, Rajesh P; Incharoensakdi, Aran; Lindblad, Peter; Madamwar, Datta; Pandey, Ashok; Larroche, Christian

    2017-11-01

    Bio-hydrogen from microalgae including cyanobacteria has attracted commercial awareness due to its potential as an alternative, reliable and renewable energy source. Photosynthetic hydrogen production from microalgae can be interesting and promising options for clean energy. Advances in hydrogen-fuel-cell technology may attest an eco-friendly way of biofuel production, since, the use of H2 to generate electricity releases only water as a by-product. Progress in genetic/metabolic engineering may significantly enhance the photobiological hydrogen production from microalgae. Manipulation of competing metabolic pathways by modulating the certain key enzymes such as hydrogenase and nitrogenase may enhance the evolution of H2 from photoautotrophic cells. Moreover, biological H2 production at low operating costs is requisite for economic viability. Several photobioreactors have been developed for large-scale biomass and hydrogen production. This review highlights the recent technological progress, enzymes involved and genetic as well as metabolic engineering approaches towards sustainable hydrogen production from microalgae. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Hydrogen Production Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Hydrogen Production Technical Team Roadmap identifies research pathways leading to hydrogen production technologies that produce near-zero net greenhouse gas (GHG) emissions from highly efficient and diverse renewable energy sources. This roadmap focuses on initial development of the technologies, identifies their gaps and barriers, and describes activities by various U.S. Department of Energy (DOE) offices to address the key issues and challenges.

  2. Technical Analysis of Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Ali T-Raissi

    2005-01-14

    The aim of this work was to assess issues of cost, and performance associated with the production and storage of hydrogen via following three feedstocks: sub-quality natural gas (SQNG), ammonia (NH{sub 3}), and water. Three technology areas were considered: (1) Hydrogen production utilizing SQNG resources, (2) Hydrogen storage in ammonia and amine-borane complexes for fuel cell applications, and (3) Hydrogen from solar thermochemical cycles for splitting water. This report summarizes our findings with the following objectives: Technoeconomic analysis of the feasibility of the technology areas 1-3; Evaluation of the hydrogen production cost by technology areas 1; and Feasibility of ammonia and/or amine-borane complexes (technology areas 2) as a means of hydrogen storage on-board fuel cell powered vehicles. For each technology area, we reviewed the open literature with respect to the following criteria: process efficiency, cost, safety, and ease of implementation and impact of the latest materials innovations, if any. We employed various process analysis platforms including FactSage chemical equilibrium software and Aspen Technologies AspenPlus and HYSYS chemical process simulation programs for determining the performance of the prospective hydrogen production processes.

  3. Biological hydrogen production from phytomass

    Energy Technology Data Exchange (ETDEWEB)

    Bartacek, J.; Zabranska, J. [Inst. of Chemical Technology, Prague (Czech Republic). Dept. of Water Technology and Environmental Engineering

    2004-07-01

    Renewable sources of energy have received wide attention lately. One candidate is hydrogen which has the added advantage of involving no greenhouse gases. Biological hydrogen production from wastewater or biowastes is a very attractive production technique. So far, most studies have concentrated on the use of photosynthetic bacteria. However, dark fermentation has recently become a popular topic of research as it has the advantage of not requiring light energy input, something that limits the performance of the photosynthetic method. While pure cultures have been used in most of the investigations to date, in industrial situations mixed cultures will probably be the norm because of unavoidable contamination. In this investigation the phytomass of amaranth (Amaranthus cruentus L) was used to produce hydrogen. Specific organic loading, organic loading, and pH were varied to study the effect on hydrogen production. 18 refs., 1 tab., 6 figs.

  4. Hydrogen production from solar energy

    Science.gov (United States)

    Eisenstadt, M. M.; Cox, K. E.

    1975-01-01

    Three alternatives for hydrogen production from solar energy have been analyzed on both efficiency and economic grounds. The analysis shows that the alternative using solar energy followed by thermochemical decomposition of water to produce hydrogen is the optimum one. The other schemes considered were the direct conversion of solar energy to electricity by silicon cells and water electrolysis, and the use of solar energy to power a vapor cycle followed by electrical generation and electrolysis. The capital cost of hydrogen via the thermochemical alternative was estimated at $575/kW of hydrogen output or $3.15/million Btu. Although this cost appears high when compared with hydrogen from other primary energy sources or from fossil fuel, environmental and social costs which favor solar energy may prove this scheme feasible in the future.

  5. Negative hydrogen ion production mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Bacal, M. [UPMC, LPP, Ecole Polytechnique, UMR CNRS 7648, Palaiseau (France); Wada, M. [School of Science and Engineering, Doshisha University, Kyoto 610-0321 (Japan)

    2015-06-15

    Negative hydrogen/deuterium ions can be formed by processes occurring in the plasma volume and on surfaces facing the plasma. The principal mechanisms leading to the formation of these negative ions are dissociative electron attachment to ro-vibrationally excited hydrogen/deuterium molecules when the reaction takes place in the plasma volume, and the direct electron transfer from the low work function metal surface to the hydrogen/deuterium atoms when formation occurs on the surface. The existing theoretical models and reported experimental results on these two mechanisms are summarized. Performance of the negative hydrogen/deuterium ion sources that emerged from studies of these mechanisms is reviewed. Contemporary negative ion sources do not have negative ion production electrodes of original surface type sources but are operated with caesium with their structures nearly identical to volume production type sources. Reasons for enhanced negative ion current due to caesium addition to these sources are discussed.

  6. Negative hydrogen ion production mechanisms

    Science.gov (United States)

    Bacal, M.; Wada, M.

    2015-06-01

    Negative hydrogen/deuterium ions can be formed by processes occurring in the plasma volume and on surfaces facing the plasma. The principal mechanisms leading to the formation of these negative ions are dissociative electron attachment to ro-vibrationally excited hydrogen/deuterium molecules when the reaction takes place in the plasma volume, and the direct electron transfer from the low work function metal surface to the hydrogen/deuterium atoms when formation occurs on the surface. The existing theoretical models and reported experimental results on these two mechanisms are summarized. Performance of the negative hydrogen/deuterium ion sources that emerged from studies of these mechanisms is reviewed. Contemporary negative ion sources do not have negative ion production electrodes of original surface type sources but are operated with caesium with their structures nearly identical to volume production type sources. Reasons for enhanced negative ion current due to caesium addition to these sources are discussed.

  7. Microwave Hydrogen Production from Methane

    Science.gov (United States)

    2012-04-01

    Reaction 2 to H2/CO2 products according to Reaction 3 at temperatures in the range of 200-400 °C in the presence of an iron-chromium or copper alloys...hydrogen for a 5-kW fuel cell system. The capital and operating costs of the technology will be estimated and compared to compressed hydrogen delivery and onsite electrolysis .

  8. Solar Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Koval, C. [Univ. of Colorado, Boulder (United States); Sutin, N. [Brookhaven National Lab., Upton, NY (United States); Turner, J. [National Renewable Energy Lab., Golden, CO (United States)

    1996-09-01

    This panel addressed different methods for the photoassisted dissociation of water into its component parts, hydrogen and oxygen. Systems considered include PV-electrolysis, photoelectrochemical cells, and transition-metal based microheterogeneous and homogeneous systems. While none of the systems for water splitting appear economically viable at the present time, the panel identified areas of basic research that could increase the overall efficiency and decrease the costs. Common to all the areas considered was the underlying belief that the water-to-hydrogen half reaction is reasonably well characterized, while the four-electron oxidation of water-to-oxygen is less well understood and represents a significant energy loss. For electrolysis, research in electrocatalysis to reduce overvoltage losses was identified as a key area for increased efficiency. Non-noble metal catalysts and less expensive components would reduce capital costs. While potentially offering higher efficiencies and lower costs, photoelectrochemical-based direct conversion systems undergo corrosion reactions and often have poor energetics for the water reaction. Research is needed to understand the factors that control the interfacial energetics and the photoinduced corrosion. Multi-photon devices were identified as promising systems for high efficiency conversion.

  9. Hydrogen local vibrational modes in semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    McCluskey, Matthew D. [Univ. of California, Berkeley, CA (United States). Dept. of Physics

    1997-06-01

    Following, a review of experimental techniques, theory, and previous work, the results of local vibrational mode (LVM) spectroscopy on hydrogen-related complexes in several different semiconductors are discussed. Hydrogen is introduced either by annealing in a hydrogen ambient. exposure to a hydrogen plasma, or during growth. The hydrogen passivates donors and acceptors in semiconductors, forming neutral complexes. When deuterium is substituted for hydrogen. the frequency of the LVM decreases by approximately the square root of two. By varying the temperature and pressure of the samples, the microscopic structures of hydrogen-related complexes are determined. For group II acceptor-hydrogen complexes in GaAs, InP, and GaP, hydrogen binds to the host anion in a bond-centered orientation, along the [111] direction, adjacent to the acceptor. The temperature dependent shift of the LVMs are proportional to the lattice thermal energy U(T), a consequence of anharmonic coupling between the LVM and acoustical phonons. In the wide band gap semiconductor ZnSe, epilayers grown by metalorganic chemical vapor phase epitaxy (MOCVD) and doped with As form As-H complexes. The hydrogen assumes a bond-centered orientation, adjacent to a host Zn. In AlSb, the DX centers Se and Te are passivated by hydrogen. The second, third, and fourth harmonics of the wag modes are observed. Although the Se-D complex has only one stretch mode, the Se-H stretch mode splits into three peaks. The anomalous splitting is explained by a new interaction between the stretch LVM and multi-phonon modes of the lattice. As the temperature or pressure is varied, and anti-crossing is observed between LVM and phonon modes.

  10. The hydrogen production; La production d'hydrogene

    Energy Technology Data Exchange (ETDEWEB)

    Aujollet, P.; Goldstein, St. [CEA Cadarach, Dir. de l' Energie Nucleaire, 13 - Saint Paul lez Durance (France); Lucchese, P. [CEA Fontenay aux Roses, Dir. des Nouvelles Technologies de l' Energie, 92 (France)

    2002-07-01

    This paper gives an overview on the implementing of the hydrogen as substitution fuel in the transportation sector. It presents also the problems of this fuel storage and exploitation and describes the production modes and their safety. It also presents the main lines of the japan HTGR program. (A.L.B.)

  11. Photoelectrochemical Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Jian

    2013-12-23

    The objectives of this project, covering two phases and an additional extension phase, were the development of thin film-based hybrid photovoltaic (PV)/photoelectrochemical (PEC) devices for solar-powered water splitting. The hybrid device, comprising a low-cost photoactive material integrated with amorphous silicon (a-Si:H or a-Si in short)-based solar cells as a driver, should be able to produce hydrogen with a 5% solar-to-hydrogen conversion efficiency (STH) and be durable for at least 500 hours. Three thin film material classes were studied and developed under this program: silicon-based compounds, copper chalcopyrite-based compounds, and metal oxides. With the silicon-based compounds, more specifically the amorphous silicon carbide (a-SiC), we achieved a STH efficiency of 3.7% when the photoelectrode was coupled to an a-Si tandem solar cell, and a STH efficiency of 6.1% when using a crystalline Si PV driver. The hybrid PV/a-SiC device tested under a current bias of -3~4 mA/cm{sup 2}, exhibited a durability of up to ~800 hours in 0.25 M H{sub 2}SO{sub 4} electrolyte. Other than the PV driver, the most critical element affecting the photocurrent (and hence the STH efficiency) of the hybrid PV/a-SiC device was the surface energetics at the a-SiC/electrolyte interface. Without surface modification, the photocurrent of the hybrid PEC device was ~1 mA/cm{sup 2} or lower due to a surface barrier that limits the extraction of photogenerated carriers. We conducted an extensive search for suitable surface modification techniques/materials, of which the deposition of low work function metal nanoparticles was the most successful. Metal nanoparticles of ruthenium (Ru), tungsten (W) or titanium (Ti) led to an anodic shift in the onset potential. We have also been able to develop hybrid devices of various configurations in a monolithic fashion and optimized the current matching via altering the energy bandgap and thickness of each constituent cell. As a result, the short

  12. Photoelectrochemical Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Jian

    2013-12-23

    The objectives of this project, covering two phases and an additional extension phase, were the development of thin film-based hybrid photovoltaic (PV)/photoelectrochemical (PEC) devices for solar-powered water splitting. The hybrid device, comprising a low-cost photoactive material integrated with amorphous silicon (a-Si:H or a-Si in short)-based solar cells as a driver, should be able to produce hydrogen with a 5% solar-to-hydrogen conversion efficiency (STH) and be durable for at least 500 hours. Three thin film material classes were studied and developed under this program: silicon-based compounds, copper chalcopyrite-based compounds, and metal oxides. With the silicon-based compounds, more specifically the amorphous silicon carbide (a-SiC), we achieved a STH efficiency of 3.7% when the photoelectrode was coupled to an a-Si tandem solar cell, and a STH efficiency of 6.1% when using a crystalline Si PV driver. The hybrid PV/a-SiC device tested under a current bias of -3~4 mA/cm{sup 2}, exhibited a durability of up to ~800 hours in 0.25 M H{sub 2}SO{sub 4} electrolyte. Other than the PV driver, the most critical element affecting the photocurrent (and hence the STH efficiency) of the hybrid PV/a-SiC device was the surface energetics at the a-SiC/electrolyte interface. Without surface modification, the photocurrent of the hybrid PEC device was ~1 mA/cm{sup 2} or lower due to a surface barrier that limits the extraction of photogenerated carriers. We conducted an extensive search for suitable surface modification techniques/materials, of which the deposition of low work function metal nanoparticles was the most successful. Metal nanoparticles of ruthenium (Ru), tungsten (W) or titanium (Ti) led to an anodic shift in the onset potential. We have also been able to develop hybrid devices of various configurations in a monolithic fashion and optimized the current matching via altering the energy bandgap and thickness of each constituent cell. As a result, the short

  13. Microbial hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, P.F.; Maness, P.C.; Martin, S. [National Renewable Energy Lab., Golden, CO (United States)] [and others

    1995-09-01

    Photosynthetic bacteria inhabit an anaerobic or microaerophilic world where H{sub 2} is produced and consumed as a shared intermediary metabolite. Within a given bacterial isolate there are as many as 4 to 6 distinct enzymes that function to evolve or consume H{sub 2}. Three of the H{sub 2}-evolving physiologies involving three different enzymes from photosynthetic bacteria have been examined in detail for commercial viability. Nitrogenase-mediated H{sub 2} production completely dissimilates many soluble organic compounds to H{sub 2} and CO{sub 2} at rates up to 131 {mu}mol H{sub 2}{sm_bullet}min{sup -1}{sm_bullet}g cdw{sup -1} and can remain active for up to 20 days. This metabolism is very energy intensive, however, which limits solar conversion efficiencies. Fermentative hydrogenase can produce H{sub 2} at rates of 440 {mu}mol{sm_bullet}min{sup -1}{sm_bullet}g cdw{sup -1} at low levels of irradiation over indefinite periods. The equilibrium for this activity is low (<0.15 atmospheres), thereby requiring gas sparging, vacuuming, or microbial scavenging to retain prolonged activity. Microbial H{sub 2} production from the CO component of synthesis or producer gases maximally reaches activities of 1.5 mmol{sm_bullet}min{sup -1}{sm_bullet}g cdw{sup -1}. Mass transport of gaseous CO into an aqueous bacterial suspension is the rate-limiting step. Increased gas pressure strongly accelerates these rates. Immobilized bacteria on solid supports at ambient pressures also show enhanced shift activity when the bulk water is drained away. Scaled-up bioreactors with 100-200 cc bed volume have been constructed and tested. The near-term goal of this portion of the project is to engineer and economically evaluate a prototype system for the biological production of H{sub 2} from biomass. The CO shift enables a positive selection technique for O{sub 2}-resistant, H{sub 2}-evolving bacterial enzymes from nature.

  14. Chemistry - Toward efficient hydrogen production at surfaces

    DEFF Research Database (Denmark)

    Nørskov, Jens Kehlet; Christensen, Claus H.

    2006-01-01

    Calculations are providing a molecular picture of hydrogen production on catalytic surfaces and within enzymes, knowledge that may guide the design of new, more efficient catalysts for the hydrogen economy.......Calculations are providing a molecular picture of hydrogen production on catalytic surfaces and within enzymes, knowledge that may guide the design of new, more efficient catalysts for the hydrogen economy....

  15. Hydrogen Storage and Production Project

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharyya, Abhijit [Univ. of Arkansas, Little Rock, AR (United States); Biris, A. S. [Univ. of Arkansas, Little Rock, AR (United States); Mazumder, M. K. [Univ. of Arkansas, Little Rock, AR (United States); Karabacak, T. [Univ. of Arkansas, Little Rock, AR (United States); Kannarpady, Ganesh [Univ. of Arkansas, Little Rock, AR (United States); Sharma, R. [Univ. of Arkansas, Little Rock, AR (United States)

    2011-07-31

    This is the final technical report. This report is a summary of the project. The goal of our project is to improve solar-to-hydrogen generation efficiency of the PhotoElectroChemical (PEC) conversion process by developing photoanodes with high absorption efficiency in the visible region of the solar radiation spectrum and to increase photo-corrosion resistance of the electrode for generating hydrogen from water. To meet this goal, we synthesized nanostructured heterogeneous semiconducting photoanodes with a higher light absorption efficiency compared to that of TiO2 and used a corrosion protective layer of TiO2. While the advantages of photoelectrochemical (PEC) production of hydrogen have not yet been realized, the recent developments show emergence of new nanostructural designs of photoanodes and choices of materials with significant gains in photoconversion efficiency.

  16. Hydrogen Production in Fusion Reactors

    OpenAIRE

    Sudo, S.; Tomita, Y.; Yamaguchi, S.; Iiyoshi, A.; Momota, H; Motojima, O.; Okamoto, M.; Ohnishi, M.; Onozuka, M; Uenosono, C.

    1993-01-01

    As one of methods of innovative energy production in fusion reactors without having a conventional turbine-type generator, an efficient use of radiation produced in a fusion reactor with utilizing semiconductor and supplying clean fuel in a form of hydrogen gas are studied. Taking the candidates of reactors such as a toroidal system and an open system for application of the new concepts, the expected efficiency and a concept of plant system are investigated.

  17. Low Cost Hydrogen Production Platform

    Energy Technology Data Exchange (ETDEWEB)

    Timothy M. Aaron, Jerome T. Jankowiak

    2009-10-16

    A technology and design evaluation was carried out for the development of a turnkey hydrogen production system in the range of 2.4 - 12 kg/h of hydrogen. The design is based on existing SMR technology and existing chemical processes and technologies to meet the design objectives. Consequently, the system design consists of a steam methane reformer, PSA system for hydrogen purification, natural gas compression, steam generation and all components and heat exchangers required for the production of hydrogen. The focus of the program is on packaging, system integration and an overall step change in the cost of capital required for the production of hydrogen at small scale. To assist in this effort, subcontractors were brought in to evaluate the design concepts and to assist in meeting the overall goals of the program. Praxair supplied the overall system and process design and the subcontractors were used to evaluate the components and system from a manufacturing and overall design optimization viewpoint. Design for manufacturing and assembly (DFMA) techniques, computer models and laboratory/full-scale testing of components were utilized to optimize the design during all phases of the design development. Early in the program evaluation, a review of existing Praxair hydrogen facilities showed that over 50% of the installed cost of a SMR based hydrogen plant is associated with the high temperature components (reformer, shift, steam generation, and various high temperature heat exchange). The main effort of the initial phase of the program was to develop an integrated high temperature component for these related functions. Initially, six independent concepts were developed and the processes were modeled to determine overall feasibility. The six concepts were eventually narrowed down to the highest potential concept. A US patent was awarded in February 2009 for the Praxair integrated high temperature component design. A risk analysis of the high temperature component was

  18. Low Cost Hydrogen Production Platform

    Energy Technology Data Exchange (ETDEWEB)

    Timothy M. Aaron, Jerome T. Jankowiak

    2009-10-16

    A technology and design evaluation was carried out for the development of a turnkey hydrogen production system in the range of 2.4 - 12 kg/h of hydrogen. The design is based on existing SMR technology and existing chemical processes and technologies to meet the design objectives. Consequently, the system design consists of a steam methane reformer, PSA system for hydrogen purification, natural gas compression, steam generation and all components and heat exchangers required for the production of hydrogen. The focus of the program is on packaging, system integration and an overall step change in the cost of capital required for the production of hydrogen at small scale. To assist in this effort, subcontractors were brought in to evaluate the design concepts and to assist in meeting the overall goals of the program. Praxair supplied the overall system and process design and the subcontractors were used to evaluate the components and system from a manufacturing and overall design optimization viewpoint. Design for manufacturing and assembly (DFMA) techniques, computer models and laboratory/full-scale testing of components were utilized to optimize the design during all phases of the design development. Early in the program evaluation, a review of existing Praxair hydrogen facilities showed that over 50% of the installed cost of a SMR based hydrogen plant is associated with the high temperature components (reformer, shift, steam generation, and various high temperature heat exchange). The main effort of the initial phase of the program was to develop an integrated high temperature component for these related functions. Initially, six independent concepts were developed and the processes were modeled to determine overall feasibility. The six concepts were eventually narrowed down to the highest potential concept. A US patent was awarded in February 2009 for the Praxair integrated high temperature component design. A risk analysis of the high temperature component was

  19. Hydrogen Production for Refuelling Applications

    Energy Technology Data Exchange (ETDEWEB)

    Hulteberg, Christian; Aagesen, Diane (Intelligent Energy, Long Beach, CA (United States))

    2009-08-15

    /day); Feedstock Cost (USD 0.15 - USD 0.45 per kg); Availability (85% - 95%). The return-on-investment is between USD 90 000 and USD 180 000 in 60 % of the 5 000 simulation runs, which leads to the conclusion that given these assumptions the owning and operation of such a unit can be profitable. As for the performance of the system, it is concluded to be within targets based on the different performance measures reported above. The conversion is in the expected range (80-85%), given the throughput of 16 kg of hydrogen per day. The efficiency as reported is in the acceptable range (approx65%), with some room for improvement within the given system architecture, if desired. However, there is a trade-off between throughput, efficiency and cost that will have to be considered in every redesign of the system. The PSA chosen for the task has performed well during the 200+ hours of operation and there is no doubt that it will be sufficient for the task. The same thing can be said with respect to the system performance with respect to thermo-mechanical stress; which was proven by operating the system for more than 500 hours and performing 58 start-and-stop cycles during the testing. There does not seem to be any major differences between operating on natural gas or methane, based on the testing performed. The slight decrease in hydrogen production can be due to a difference in the H{sub 2}/CO ratio between the various fuels. As expected the efficiency increases with load as well as the hydrogen production rate. Based on the results disseminated above, there is no indication why the current reactor system cannot be configured into a field deployable system. The operation of the system has given valuable experience that will be embedded into any field deployed unit

  20. Hydrogen production processes; Procedes de production d'hydrogene

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    The goals of this first Gedepeon workshop on hydrogen production processes are: to stimulate the information exchange about research programs and research advances in the domain of hydrogen production processes, to indicate the domains of interest of these processes and the potentialities linked with the coupling of a nuclear reactor, to establish the actions of common interest for the CEA, the CNRS, and eventually EDF, that can be funded in the framework of the Gedepeon research group. This document gathers the slides of the 17 presentations given at this workshop and dealing with: the H{sub 2} question and the international research programs (Lucchese P.); the CEA's research program (Lucchese P., Anzieu P.); processes based on the iodine/sulfur cycle: efficiency of a facility - flow-sheets, efficiencies, hard points (Borgard J.M.), R and D about the I/S cycle: Bunsen reaction (Colette S.), R and D about the I/S cycle: the HI/I{sub 2}/H{sub 2}O system (Doizi D.), demonstration loop/chemical engineering (Duhamet J.), materials and corrosion (Terlain A.); other processes under study: the Westinghouse cycle (Eysseric C.), other processes under study at the CEA (UT3, plasma,...) (Lemort F.), database about thermochemical cycles (Abanades S.), Zn/ZnO cycle (Broust F.), H{sub 2} production by cracking, high temperature reforming with carbon trapping (Flamant G.), membrane technology (De Lamare J.); high-temperature electrolysis: SOFC used as electrolyzers (Grastien R.); generic aspects linked with hydrogen production: technical-economical evaluation of processes (Werkoff F.), thermodynamic tools (Neveu P.), the reactor-process coupling (Aujollet P.). (J.S.)

  1. Solar based hydrogen production systems

    CERN Document Server

    Dincer, Ibrahim

    2013-01-01

    This book provides a comprehensive analysis of various solar based hydrogen production systems. The book covers first-law (energy based) and second-law (exergy based) efficiencies and provides a comprehensive understanding of their implications. It will help minimize the widespread misuse of efficiencies among students and researchers in energy field by using an intuitive and unified approach for defining efficiencies. The book gives a clear understanding of the sustainability and environmental impact analysis of the above systems. The book will be particularly useful for a clear understanding

  2. GTI's hydrogen programs: hydrogen production, storage, and applications

    Institute of Scientific and Technical Information of China (English)

    范钦柏

    2006-01-01

    The use of hydrogen as an energy carrier could help address our concerns about energy security, global climate change,and air quality. Fuel cells are an important enabling technology for the Hydrogen Future and have the potential to revolutionize theway we power our nation, offering cleaner, more-efficient alternatives to the combustion of gasoline and other fossil fuels.For over 45 years, GTI has been active in hydrogen energy research, development and demonstration. The Institute has extensive experience and on-going work in all aspects of the hydrogen energy economy including production, delivery, infrastructure,use, safety and public policy. This paper discusses the recent GTI programs in hydrogen production, hydrogen storage, and proton exchange membrane fuel cells (PEMFC) and solid oxide fuel cells (SOFC).

  3. Maximizing hydrogen production by cyanobacteria

    Energy Technology Data Exchange (ETDEWEB)

    Bothe, H.; Winkelmann, S.; Boison, G. [Botanical Inst., The Univ. of Cologne, Cologne (Germany)

    2008-03-15

    When incubated anaerobically, in the light, in the presence of C{sub 2}H{sub 2} and high concentrations of H{sub 2}, both Mo-grown Anabaena variabilis and either Mo- or V-grown Anabaena azotica produce large amounts of H{sub 2} in addition to the H{sub 2} initially added. In contrast, C{sub 2}H{sub 2}-reduction is diminished under these conditions. The additional H{sub 2}-production mainly originates from nitrogenase with the V-enzyme being more effective than the Mo-protein. This enhanced H{sub 2}-production in the presence of added H{sub 2} and C{sub 2}H{sub 2} should be of interest in approaches to commercially exploit solar energy conversion by cyanobacterial photosynthesis for the generation of molecular hydrogen as a clean energy source. (orig.)

  4. Dedicated nuclear facilities for electrolytic hydrogen production

    Science.gov (United States)

    Foh, S. E.; Escher, W. J. D.; Donakowski, T. D.

    1979-01-01

    An advanced technology, fully dedicated nuclear-electrolytic hydrogen production facility is presented. This plant will produce hydrogen and oxygen only and no electrical power will be generated for off-plant use. The conceptual design was based on hydrogen production to fill a pipeline at 1000 psi and a 3000 MW nuclear base, and the base-line facility nuclear-to-shaftpower and shaftpower-to-electricity subsystems, the water treatment subsystem, electricity-to-hydrogen subsystem, hydrogen compression, efficiency, and hydrogen production cost are discussed. The final conceptual design integrates a 3000 MWth high-temperature gas-cooled reactor operating at 980 C helium reactor-out temperature, direct dc electricity generation via acyclic generators, and high-current density, high-pressure electrolyzers based on the solid polymer electrolyte approach. All subsystems are close-coupled and optimally interfaced and pipeline hydrogen is produced at 1000 psi. Hydrogen costs were about half of the conventional nuclear electrolysis process.

  5. Hydrogen Learning for Local Leaders – H2L3

    Energy Technology Data Exchange (ETDEWEB)

    Serfass, Patrick

    2017-03-30

    The Hydrogen Learning for Local Leaders program, H2L3, elevates the knowledge about hydrogen by local government officials across the United States. The program reaches local leaders directly through “Hydrogen 101” workshops and webinar sessions; the creation and dissemination of a unique report on the hydrogen and fuel cell market in the US, covering 57 different sectors; and support of the Hydrogen Student Design Contest, a competition for interdisciplinary teams of university students to design hydrogen and fuel cell systems based on technology that’s currently commercially available.

  6. Localized chaos in one-dimensional hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Humm, D.C.; Saltz, D.; Nayfeh, M.H. (Department of Physics, University of Illinois at Urbana-Champaign, 1110 West Green Street, Urbana, Illinois 61801 (USA))

    1990-08-01

    We calculate the response of hydrogen to the presence of both a strong dc electric field (necessary to isolate a nearly one-dimensional motion) and a strong radiation field of higher frequency than the binding energy of the system, a regime that has not previously been examined by theory or experiment. We determine the classical ionization threshold, the quantum-delocalization threshold, and the threshold of {ital n} mixing due to chaotic effects. The analysis indicates that the dc field can have a dramatic effect on the quantum localization of classically chaotic diffusion, changing the delocalization threshold by more than an order of magnitude. Moreover, this system provides a large spectral region in which quantum-mechanical localization inhibits classical chaotic diffusion. This theory is well suited to experimental testing.

  7. Photobiological hydrogen production and carbon dioxide sequestration

    Science.gov (United States)

    Berberoglu, Halil

    Photobiological hydrogen production is an alternative to thermochemical and electrolytic technologies with the advantage of carbon dioxide sequestration. However, it suffers from low solar to hydrogen energy conversion efficiency due to limited light transfer, mass transfer, and nutrient medium composition. The present study aims at addressing these limitations and can be divided in three parts: (1) experimental measurements of the radiation characteristics of hydrogen producing and carbon dioxide consuming microorganisms, (2) solar radiation transfer modeling and simulation in photobioreactors, and (3) parametric experiments of photobiological hydrogen production and carbon dioxide sequestration. First, solar radiation transfer in photobioreactors containing microorganisms and bubbles was modeled using the radiative transport equation (RTE) and solved using the modified method of characteristics. The study concluded that Beer-Lambert's law gives inaccurate results and anisotropic scattering must be accounted for to predict the local irradiance inside a photobioreactor. The need for accurate measurement of the complete set of radiation characteristics of microorganisms was established. Then, experimental setup and analysis methods for measuring the complete set of radiation characteristics of microorganisms have been developed and successfully validated experimentally. A database of the radiation characteristics of representative microorganisms have been created including the cyanobacteria Anabaena variabilis, the purple non-sulfur bacteria Rhodobacter sphaeroides and the green algae Chlamydomonas reinhardtii along with its three genetically engineered strains. This enabled, for the first time, quantitative assessment of the effect of genetic engineering on the radiation characteristics of microorganisms. In addition, a parametric experimental study has been performed to model the growth, CO2 consumption, and H 2 production of Anabaena variabilis as functions of

  8. Hydrogen production from microbial strains

    Science.gov (United States)

    Harwood, Caroline S; Rey, Federico E

    2012-09-18

    The present invention is directed to a method of screening microbe strains capable of generating hydrogen. This method involves inoculating one or more microbes in a sample containing cell culture medium to form an inoculated culture medium. The inoculated culture medium is then incubated under hydrogen producing conditions. Once incubating causes the inoculated culture medium to produce hydrogen, microbes in the culture medium are identified as candidate microbe strains capable of generating hydrogen. Methods of producing hydrogen using one or more of the microbial strains identified as well as the hydrogen producing strains themselves are also disclosed.

  9. Fermentative hydrogen production by diverse microflora

    Energy Technology Data Exchange (ETDEWEB)

    Baghchehsaraee, B.; Nakhla, G.; Karamanev, D.; Margaritis, A. [Western Ontario Univ., London, ON (Canada). Dept. of Chemical and Biochemical Engineering

    2009-07-01

    This paper presented the results of a study in which hydrogen was produced from activated sludge. This diverse bacterial source has been compared to microflora from anaerobic digester sludge. Batch experiments were conducted at mesophilic (37 degrees C) and thermophilic (55 degrees C) temperatures. The hydrogen production yields with activated sludge at mesophilic and thermophilic temperatures were 0.25 and 0.93 mol H{sub 2}/mol glucose, respectively. The maximum hydrogen production rates with activated sludge in both temperatures were 4.2 mL/h. Anaerobic digester sludge showed higher hydrogen production yields and rates at both mesophilic and thermophilic temperatures. Repeated batch experiments with activated sludge resulted in increased hydrogen production in consecutive batches. However, the formation of lactic acid and ethanol resulted in unstable hydrogen production in the repeated batches.

  10. Prospects of solar thermal hydrogen production processes

    Energy Technology Data Exchange (ETDEWEB)

    Pregger, Thomas; Krewitt, Wolfram [German Aerospace Center (DLR), Institute of Technical Thermodynamics, Department of Systems Analysis and Technology Assessment, Pfaffenwaldring 38-40, D-70569 Stuttgart (Germany); Graf, Daniela; Sattler, Christian; Roeb, Martin; Moeller, Stephan [German Aerospace Center (DLR), Institute of Technical Thermodynamics, Department of Solar Research, Linder Hoehe, D-51147 Cologne (Germany)

    2009-05-15

    This article provides a critical discussion of prospects of solar thermal hydrogen production in terms of technological and economic potentials and their possible role for a future hydrogen supply. The study focuses on solar driven steam methane reforming, thermochemical cycles, high temperature water electrolysis and solar methane cracking. Development status and technological challenges of the processes and objectives of ongoing research are described. Estimated hydrogen production costs are shown in comparison to other options. A summary of current discussions and today's scenarios of future use of hydrogen as an energy carrier and a brief overview on the development status of end-use technologies characterise uncertainties whether hydrogen could emerge as important energy carrier until 2050. Another focus is on industrial hydrogen demand in areas with high direct solar radiation which may be the main driver for the further development of solar thermal hydrogen production processes in the coming decades. (author)

  11. Microstructured reactors for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Aartun, Ingrid

    2005-07-01

    Small scale hydrogen production by partial oxidation (POX) and oxidative steam reforming (OSR) have been studied over Rh-impregnated microchannel Fecralloy reactors and alumina foams. Trying to establish whether metallic microchannel reactors have special advantages for hydrogen production via catalytic POX or OSR with respect to activity, selectivity and stability was of special interest. The microchannel Fecralloy reactors were oxidised at 1000 deg C to form a {alpha}-Al2O3 layer in the channels in order to enhance the surface area prior to impregnation. Kr-BET measurements showed that the specific surface area after oxidation was approximately 10 times higher than the calculated geometric surface area. Approximately 1 mg Rh was deposited in the channels by impregnation with an aqueous solution of RhCl3. Annular pieces (15 mm o.d.,4 mm i.d., 14 mm length) of extruded {alpha}-Al2O3 foams were impregnated with aqueous solutions of Rh(NO3)3 to obtain 0.01, 0.05 and 0.1 wt.% loadings, as predicted by solution uptake. ICP-AES analyses showed that the actual Rh loadings probably were higher, 0.025, 0.077 and 0.169 wt.% respectively. One of the microchannel Fecralloy reactors and all Al2O3 foams were equipped with a channel to allow for temperature measurement inside the catalytic system. Temperature profiles obtained along the reactor axes show that the metallic microchannel reactor is able to minimize temperature gradients as compared to the alumina foams. At sufficiently high furnace temperature, the gas phase in front of the Rh/Al2O3/Frecralloy microchannel reactor and the 0.025 wt.% Rh/Al2O3 foams ignites. Gas phase ignition leads to lower syngas selectivity and higher selectivity to total oxidation products and hydrocarbon by-products. Before ignition of the gas phase the hydrogen selectivity is increased in OSR as compared to POX, the main contribution being the water-gas shift reaction. After gas phase ignition, increased formation of hydrocarbon by-products

  12. Petroleum Refinery Hydrogen Production Unit: Exergy and Production Cost Evaluation

    Directory of Open Access Journals (Sweden)

    Silvio de Oliveira Júnior

    2008-12-01

    Full Text Available Some specific processes are required to obtain pure hydrogen and the most usual one is natural gas reforming, where natural gas reacts with superheated steam producing H2, CO, CO2 and H2O. This paper presents the exergy and production costs evaluation of a complete hydrogen production unit of a petroleum refinery. The hydrogen production unit analysed in this paper has to supply 550,000 Nm3 of hydrogen per day to purify diesel oil. Based on a synthesis plant of the hydrogen production unit, the exergy efficiency of each component and of the overall plant are calculated. The hydrogen production cost is determined by means of a thermoeconomic analysis in which the equality cost partition method is employed, including capital and operational costs, in order to determine the production cost of hydrogen and other products of the plant.

  13. Hydrogen production by recombinant Escherichia coli strains

    Science.gov (United States)

    Maeda, Toshinari; Sanchez‐Torres, Viviana; Wood, Thomas K.

    2012-01-01

    Summary The production of hydrogen via microbial biotechnology is an active field of research. Given its ease of manipulation, the best‐studied bacterium Escherichia coli has become a workhorse for enhanced hydrogen production through metabolic engineering, heterologous gene expression, adaptive evolution, and protein engineering. Herein, the utility of E. coli strains to produce hydrogen, via native hydrogenases or heterologous ones, is reviewed. In addition, potential strategies for increasing hydrogen production are outlined and whole‐cell systems and cell‐free systems are compared. PMID:21895995

  14. Redirection of metabolism for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Harwood, Caroline S.

    2011-11-28

    This project is to develop and apply techniques in metabolic engineering to improve the biocatalytic potential of the bacterium Rhodopseudomonas palustris for nitrogenase-catalyzed hydrogen gas production. R. palustris, is an ideal platform to develop as a biocatalyst for hydrogen gas production because it is an extremely versatile microbe that produces copious amounts of hydrogen by drawing on abundant natural resources of sunlight and biomass. Anoxygenic photosynthetic bacteria, such as R. palustris, generate hydrogen and ammonia during a process known as biological nitrogen fixation. This reaction is catalyzed by the enzyme nitrogenase and normally consumes nitrogen gas, ATP and electrons. The applied use of nitrogenase for hydrogen production is attractive because hydrogen is an obligatory product of this enzyme and is formed as the only product when nitrogen gas is not supplied. Our challenge is to understand the systems biology of R. palustris sufficiently well to be able to engineer cells to produce hydrogen continuously, as fast as possible and with as high a conversion efficiency as possible of light and electron donating substrates. For many experiments we started with a strain of R. palustris that produces hydrogen constitutively under all growth conditions. We then identified metabolic pathways and enzymes important for removal of electrons from electron-donating organic compounds and for their delivery to nitrogenase in whole R. palustris cells. For this we developed and applied improved techniques in 13C metabolic flux analysis. We identified reactions that are important for generating electrons for nitrogenase and that are yield-limiting for hydrogen production. We then increased hydrogen production by blocking alternative electron-utilizing metabolic pathways by mutagenesis. In addition we found that use of non-growing cells as biocatalysts for hydrogen gas production is an attractive option, because cells divert all resources away from growth and

  15. Solar Thermochemical Hydrogen Production Plant Design

    OpenAIRE

    Littlefield, Jesse

    2012-01-01

    A plant was designed that uses a solar sulfur-ammonia thermochemical water-splitting cycle for the production of hydrogen. Hydrogen is useful as a fuel for stationary and mobile fuel cells. The chemical process simulator Aspen Plus® was used to model the plant and conduct simulations. The process utilizes the electrolytic oxidation of aqueous ammonium sulfite in the hydrogen production half cycle and the thermal decomposition of molten potassium pyrosulfate and gaseous sulfur trioxide in t...

  16. Hydrogen production by alkaline water electrolysis

    OpenAIRE

    Santos, Diogo M. F.; Sequeira,César A. C.; José L. Figueiredo

    2013-01-01

    Water electrolysis is one of the simplest methods used for hydrogen production. It has the advantage of being able to produce hydrogen using only renewable energy. To expand the use of water electrolysis, it is mandatory to reduce energy consumption, cost, and maintenance of current electrolyzers, and, on the other hand, to increase their efficiency, durability, and safety. In this study, modern technologies for hydrogen production by water electrolysis have been investigated. In this article...

  17. Economics and market potential of hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Swisher, Dr., James; Berger, Dr., Beverly; Fickett, Dr., A.; Dickson, Dr., E.

    1978-09-01

    A study was undertaken to evaluate the economics of producing hydrogen from coal and from water and to assess the market potential for this hydrogen in chemical and fuel applications. Results of this study are summarized. Current chemical applications of hydrogen in manufacturing ammonia and methanol, in refining petroleum and in specialty uses provide a base market for penetration by new hydrogen production technologies, although prospects for the use of hydrogen in fuel applications remain unclear. Electrolysis and coal gasification will be complementary, not competitive, technologies for producing hydrogen. Coal gasification plants are better suited to production of large quantities of hydrogen, while electrolyzers are better suited to the production of hydrogen for small-scale uses. Hydrogen produced through coal gasification may be economical in chemical applications (e.g., ammonia production) by the late 1990's. Development programs now underway are expected to provide new coal gasification technologies with lower first costs and higher efficiencies than current technologies. An on-site coal gasification plant supplying hydrogen in the quantities usually required in chemical applications (from 10 to 100 million cubic feet per day) will be smaller than is generally proposed for syngas plants. Growth in smaller scale specialty uses of hydrogen and improvements in the technology for electrolysis will create conditions favorable to expanded use of hydrogen produced through water electrolysis. The major constraint on use of electrolysis will be the availability of low cost electricity. Shortages of natural gas caused by declining domestic production could induce shifts to producing hydrogen through electrolysis or through coal gasification earlier in time (i.e., the late 1980's or early 1990's) than is suggested by comparative cost calculations alone.

  18. Continuous hydrogen production from organic waste

    Energy Technology Data Exchange (ETDEWEB)

    Noike, T.; Li, Y.Y. [Tohoku Univ., Sendai (Japan). Dept. of Civil Engineering; Ko, I.B. [Cheju National Univ. Jeju (Korea, Republic of). Dept. of Environmental Engineering; Yokoyama, S. [Sanki Engineering CP., Ltd. (Japan); Kohno, Y. [Ex Corporation City and Environmental Planning, Research (Japan)

    2004-07-01

    Hydrogen is seen as a promising fuel for the future. Microbial fermentation of organic wastes is an attractive option. However, it has often been observed that hydrogen production in a continuously-fed reactor stops after a period of time. In this investigation, the effect of pH on lactic acid bacteria in continuous hydrogen production is studied. It was found that the antibiotic effect of the bacteria is prevented by keeping the pH greater than five. To establish what stops continuous hydrogen production, a continuous experiment was run using waste from bean curd manufacturing at a pH of 5.5 and a temperature of 35 degrees celsius. An increase in substrate concentration and the addition of nitrogen preferentially produced acetic and butyric acids and suppressed the production of propionic acid. Because of this, continuous hydrogen production was made possible. 4 refs., 5 tabs., 5 figs.

  19. Hydrogen production through biocatalyzed electrolysis

    NARCIS (Netherlands)

    Rozendal, R.A.

    2007-01-01

    cum laude graduation (with distinction) To replace fossil fuels, society is currently considering alternative clean fuels for transportation. Hydrogen could be such a fuel. In theory, large amounts of renewable hydrogen can be produced from organic contaminants in wastewater. During his PhD research

  20. Hydrogen production through biocatalyzed electrolysis

    NARCIS (Netherlands)

    Rozendal, R.A.

    2007-01-01

    cum laude graduation (with distinction) To replace fossil fuels, society is currently considering alternative clean fuels for transportation. Hydrogen could be such a fuel. In theory, large amounts of renewable hydrogen can be produced from organic contaminants in wastewater. During his PhD research

  1. Scenarios of hydrogen production from wind power

    Energy Technology Data Exchange (ETDEWEB)

    Klaric, Mario

    2010-09-15

    Since almost total amount of hydrogen is currently being produced from natural gas, other ways of cleaner and 'more renewable' production should be made feasible in order to make benchmarks for total 'hydrogen economy'. Hydrogen production from wind power combined with electrolysis imposes as one possible framework for new economy development. In this paper various wind-to-hydrogen scenarios were calculated. Cash flows of asset based project financing were used as decision making tool. Most important parameters were identified and strategies for further research and development and resource allocation are suggested.

  2. Bioreactor design for photofermentative hydrogen production.

    Science.gov (United States)

    Uyar, Basar

    2016-09-01

    Hydrogen will become a significant fuel in the near future. Photofermentative production of hydrogen is a promising and sustainable process. The design, construction and successful operation of the photobioreactors are of critical importance for photofermentative hydrogen production and became a major field of research where novel technologies are developed and adapted frequently. This paper gives an overview of the design aspects related to photobioreactors giving particular attention to design limitations, construction material, type, operating mode and scale-up. Sub-components of the overall system setup such as mixing, temperature control and hydrogen collection are also discussed. Recent achievements in the photobioreactor technologies are described.

  3. Hydrogen production through biocatalyzed electrolysis

    OpenAIRE

    Rozendal, R.A.

    2007-01-01

    cum laude graduation (with distinction) To replace fossil fuels, society is currently considering alternative clean fuels for transportation. Hydrogen could be such a fuel. In theory, large amounts of renewable hydrogen can be produced from organic contaminants in wastewater. During his PhD research René Rozendal has developed a new technology for this purpose: biocatalyzed electrolysis. The innovative step of biocatalyzed electrolysis is the application of electrochemically active microorgan...

  4. The hydrogen gas clearance method for liver blood flow examination: inhalation or local application of hydrogen?

    Science.gov (United States)

    Metzger, H P

    1989-01-01

    The combined method of hydrogen inhalation and local hydrogen production enable the determination of hepatic blood flow (HBF) and local hepatic blood flow (LHBF). LHBF was registered within a small superficial tissue volume of 0.5 mm in diameter by means of a multi-wire electrode having 200 microns producing and 100 microns measuring wires arranged within less than 300 microns distance between the measuring wires. The feeding current for hydrogen production was 1 microA, the potential less than 10 V. The clearance in response to inhalation was registered by means of the same measuring electrodes within the same tissue volume. Spontaneously breathing rats (Wistar-Frömter strain, 180-230 g bw, N = 19, ketamin-xylazine anesthesia, artificial respiration) showed the following flow values: HBF +/- SD = 0.50 +/- 0.26 ml/g.min, n = 48 registrations; LHBF +/- SD = 4.66 +/- 2.13 ml/g.min, n = 43. The validity of the combined method is demonstrated in the LHBF/HBF graph which summarizes the data of hemorrhagic and control animals, m = 0.1 and yo = 0.001. The correlation coefficient of r = 0.685 shows a reasonable correlation of the combined data despite the wide scattering of the individual values.

  5. Production of Hydrogen from Underground Coal Gasification

    Science.gov (United States)

    Upadhye, Ravindra S.

    2008-10-07

    A system of obtaining hydrogen from a coal seam by providing a production well that extends into the coal seam; positioning a conduit in the production well leaving an annulus between the conduit and the coal gasification production well, the conduit having a wall; closing the annulus at the lower end to seal it from the coal gasification cavity and the syngas; providing at least a portion of the wall with a bifunctional membrane that serves the dual purpose of providing a catalyzing reaction and selectively allowing hydrogen to pass through the wall and into the annulus; and producing the hydrogen through the annulus.

  6. Fusion reactors for hydrogen production via electrolysis

    Science.gov (United States)

    Fillo, J. A.; Powell, J. R.; Steinberg, M.

    The decreasing availability of fossil fuels emphasizes the need to develop systems which will produce synthetic fuel to substitute for and supplement the natural supply. An important first step in the synthesis of liquid and gaseous fuels is the production of hydrogen. Thermonuclear fusion offers an inexhaustible source of energy for the production of hydrogen from water. Depending on design, electric generation efficiencies of 40 to 60% and hydrogen production efficiencies by high temperature electrolysis of 50 to 70% are projected for fusion reactors using high temperature blankets.

  7. Developments and constraints in fermentative hydrogen production

    NARCIS (Netherlands)

    Bartacek, J.; Zabranska, J.; Lens, P.N.L.

    2007-01-01

    Fermentative hydrogen production is a novel aspect of anaerobic digestion. The main advantage of hydrogen is that it is a clean and renewable energy source/carrier with high specific heat of combustion and no contribution to the Greenhouse effect, and can be used in many industrial applications. Thi

  8. Hydrogen production from biomass over steam gasification

    Energy Technology Data Exchange (ETDEWEB)

    Rauch, R.; Potetz, A.; Hofbauer, H. [Vienna Univ. of Technology (Austria). Inst. of Chemical Engineering; Weber, G. [Bioenergy 2020+, Guessing (Austria)

    2010-12-30

    Renewable hydrogen is one option for a clean energy carrier in the future. There were several research programs in the past, to produce hydrogen on a renewable basis by electrolysis, direct conversion of water or by gasification of biomass. None of these options were developed to a stage, that they could be used on a commercial basis. At the moment almost all hydrogen is produced from fossil fuels and one main consumer of hydrogen are refineries. So a good option to demonstrate the production of renewable hydrogen and bring it later into the market is over refineries. The most economic option to produce renewable hydrogen at the moment is over gasification of biomass. In Austria an indirect gasification system was developed and is demonstrated in Guessing, Austria. The biomass CHP Guessing uses the allothermal steam dual fluidised bed gasifier and produces a high grade product gas, which is used at the moment for the CHP in a gas engine. As there is no nitrogen in the product gas and high hydrogen content, this gas can be also used as synthesis gas or for production of hydrogen. The main aim of this paper is to present the experimental and simulation work to convert biomass into renewable hydrogen. The product gas of the indirect gasification system is mainly hydrogen, carbon monoxide, carbon dioxide and methane. Within the ERA-Net project ''OptiBtLGas'' the reforming of methane and the CO-shift reaction was investigated to convert all hydrocarbons and carbon monoxide to hydrogen. On basis of the experimental results the mass- and energy balances of a commercial 100 MW fuel input plant was done. Here 3 different cases of complexity of the overall plant were simulated. The first case was without reforming and CO-shift, only by hydrogen separation. The second case was by including steam - reforming and afterwards separation of hydrogen. The third case includes hydrocarbon reforming, CO-shift and hydrogen separation. In all cases the off-gases (CO

  9. Production of hydrogen by superadiabatic decomposition of hydrogen sulfide

    Energy Technology Data Exchange (ETDEWEB)

    Slimane, R.B.; Lau, F.S.; Dihu, R. [Gas Technology Inst., Des Plaines, IL (United States); Bingue, J.P.; Saveliev, A.V.; Fridman, A.A.; Kennedy, L.A. [Illinois Univ., Chicago, IL (United States)

    2002-07-01

    It is expected that hydrogen will become the fuel of choice for advanced technologies. Hydrogen is currently used as feedstock in the synthesis of ammonia and methanol, in the desulfurization and hydrocracking at oil refineries, and in the upgrading of hydrocarbon resources such as heavy oil and coal. Hydrogen sulfide (H{sub 2}S) is regarded as a mineral from which both hydrogen and sulfur can be extracted. Since there are large amounts of H{sub 2}S available worldwide, significant research has gone into the development of converting hydrogen sulfide into hydrogen through thermal decomposition. The high temperature required for the reaction, however, makes the approach impractical. This paper presents results of a study using a new approach to overcome the limitations of thermal decomposition. In this newly developed process, operation at very high temperatures is possible and economical through oxidation of part of the H{sub 2}S to provide the energy needed for the decomposition reaction. Partial oxidation is carried out in the presence of an inert, porous, high-capacity medium and the heat exchange results in flame temperatures that exceed the adiabatic flame temperature of the gas mixture. This process is less stringent than the Claus process because of the required feed gas conditioning. SO{sub 2} emissions inevitably form because part of the H{sub 2}S is oxidized to generate heat. However, SO{sub 2} is not expected to form to a significant degree. It was concluded that the product/byproduct separation schemes need to be examined further to have a better idea regarding the cost of hydrogen production from this process. 6 refs., 5 figs.

  10. Photobiological production of hydrogen using cyanobacteria

    Energy Technology Data Exchange (ETDEWEB)

    Borthakur, D.; McKinley, K.R.; Bylina, E.J. [Univ. of Hawaii, Honolulu, HI (United States)

    1995-09-01

    Cyanobacteria are capable of generating hydrogen using sunlight and water. In both Spirulina and Anabaena, there is a soluble reversible hydrogenase that is involved in hydrogen evolution under anaerobic conditions in the dark. In addition, the nitrogen-fixing cyanobacterium Anabaena produces hydrogen as a by-product of nitrogen fixation. Most of this hydrogen is recaptured by a membrane-bound uptake hydrogenase present in Anabaena cells. Experiments have continued to develop a gene transfer system in Spirulina in preparation for improved hydrogen production via genetic manipulation of the reversible hydrogenase. We have identified and characterized four restriction enzymes in Spirulina and cloned the genes for two methylases that protect their own DNA from cleavage by restriction enzymes. We have also cloned and sequenced parts of hupB and hupM genes involved in the synthesis of uptake hydrogenase in Anabaena. Successful cloning of these hup genes represents an important and necessary step in our project because this will enable us to construct Anabaena strains with enhanced hydrogen production ability by disrupting the hup genes involved in hydrogen uptake. We are also setting up a bio-reactor to determine the amount of hydrogen released by different Spirulina and Anabaena strains under different physiological conditions.

  11. Biological hydrogen production from industrial wastewaters

    Energy Technology Data Exchange (ETDEWEB)

    Peixoto, Guilherme; Pantoja Filho, Jorge Luis Rodrigues; Zaiat, Marcelo [Universidade de Sao Paulo (EESC/USP), Sao Carlos, SP (Brazil). School of Engineering. Dept. Hydraulics and Sanitation], Email: peixoto@sc.usp.br

    2010-07-01

    This research evaluates the potential for producing hydrogen in anaerobic reactors using industrial wastewaters (glycerol from bio diesel production, wastewater from the parboilization of rice, and vinasse from ethanol production). In a complementary experiment the soluble products formed during hydrogen production were evaluated for methane generation. The assays were performed in batch reactors with 2 liters volume, and sucrose was used as a control substrate. The acidogenic inoculum was taken from a packed-bed reactor used to produce hydrogen from a sucrose-based synthetic substrate. The methanogenic inoculum was taken from an upflow anaerobic sludge blanket reactor treating poultry slaughterhouse wastewater. Hydrogen was produced from rice parboilization wastewater (24.27 ml H{sub 2} g{sup -1} COD) vinasse (22.75 ml H{sub 2} g{sup -1} COD) and sucrose (25.60 ml H{sub 2} g{sup -1} COD), while glycerol only showed potential for methane generation. (author)

  12. Fermentative hydrogen production by diverse microflora

    Energy Technology Data Exchange (ETDEWEB)

    Baghchehsaraee, B.; Nakhla, G.; Karamanev, D.; Margaritis, A. [Dept. of Chemical and Biochemical Engineering, Univ. of Western Ontario, London, Ontario (Canada)

    2009-07-01

    'Full text': In this study of hydrogen production with activated sludge, a diverse bacterial source has been investigated and compared to microflora from anaerobic digester sludge, which is less diverse. Batch experiments were conducted at mesophilic (37 {sup o}C) and thermophilic (55 {sup o}C) temperatures. The hydrogen production yields with activated sludge at 37 {sup o}C and 55 {sup o}C were 0.25 and 0.93 mol H{sub 2}/mol glucose, respectively. The maximum hydrogen production rates with activated sludge in both temperatures were 4.2 mL/h. Anaerobic digester sludge showed higher hydrogen production yields and rates at both mesophilic and thermophilic temperatures. The results of repeated batch experiments with activated sludge showed an increase in the hydrogen production during the consecutive batches. However, hydrogen production was not stable along the repeated batches. The observed instability was due to the formation of lactic acid and ethanol. (author)

  13. Recent Developments in Biological Hydrogen Production Processes

    Directory of Open Access Journals (Sweden)

    DEBABRATA DAS

    2008-07-01

    Full Text Available Biohydrogen production technology can utilize renewable energy sources like biomass for the generation of hydrogen, the cleanest form of energy for the use of mankind. However, major constraints to the commercialization of these processes include lower hydrogen yields and rates of hydrogen production. To overcome these bottlenecks intensive research work has already been carried out on the advancement of these processes such as the development of genetically modified microorganisms, the improvement of the bioreactor design, molecular engineering of the key enzyme hydrogenases, the development of two stage processes, etc. The present paper explores the recent advancements that have been made till date and also presents the state of the art in molecular strategies to improve the hydrogen production.

  14. Enhancing fermentative hydrogen production from sucrose.

    Science.gov (United States)

    Perera, Karnayakage Rasika J; Nirmalakhandan, Nagamany

    2010-12-01

    This study evaluated the hypothesis that fermentative hydrogen production from organic-rich feedstock could be enhanced by supplementing with waste materials such as cattle manure that could provide nutritional needs, buffering capacity, and native hydrogen-producing organisms. This hypothesis was tested in batch reactors fed with sucrose blended with cattle manure run at 25 degrees C without any nutrient supplements, pH adjustments, buffering, or gas-sparging. Hydrogen production rates in these reactors ranged 16-30 mL H(2)/g DeltaCOD-day, while hydrogen content in the biogases ranged 50-59%. Compared to literature studies conducted at higher temperatures, hydrogen yields found in this study at 25 degrees C were higher in the range of 3.8-4.7 mol H(2)/mol sucrose added, with higher positive net energy yields (>14 kJ/L). This study demonstrated that cattle manure as a supplement could not only provide hydrogen-producing seed, nutritional needs, and buffering capacity, but also increase hydrogen yield by approximately 10%, improving the economic viability of fermentative biohydrogen production from sugary wastes.

  15. Calculation Research of Hydrogen Production Amount in Containment after LOCAL in PWR Nuclear Power Plants%压水堆核电厂失水事故后安全壳内产氢量计算研究

    Institute of Scientific and Technical Information of China (English)

    胡建军

    2013-01-01

    The ORIGEN2 code is adopted to calculate the amount of hydrogen production in the core and sump region after LOCAL in PWR nuclear power plants,to reduce the conservatism for the design evaluation of the combustible gas control in the containment.The calculation model of radiolytic decomposition coolant and other related calculation model are used to calculate the amount of hYdrogen production after LOCA in a 600MW PWR nuclear power plant,and the results show that over conservatism of the original evaluation,and there still exists abundant time to prepare and startup the hydrogen recombiners in the containment after LOCAL.%采用ORIGEN2程序对压水堆核电厂失水事故工况下堆芯区和地坑区氢气的产生量进行计算,以合理减少安全壳内可燃气体的控制设计评价的保守性.通过冷却剂的辐照分解产氢以及其他相关计算模型,对600MW(电功率)级压水堆核电厂失水事故工况下的氢气产生量进行计算.计算结果表明原评价结果过于保守,在核电厂失水事故后仍有充分的时间准备投入安全壳内氢气复合器.

  16. Solar driven technologies for hydrogen production

    Directory of Open Access Journals (Sweden)

    Medojević Milovan M.

    2016-01-01

    Full Text Available Bearing in mind that the production of hydrogen based on renewable energy sources, without doubt, is an important aspect to be taken into account when considering the potential of this gas, where as particularly interesting technologies stand out the ones which are based on the use of solar energy to produce hydrogen. The goal of this paper provides basic technological trajectories, with the possibility of combining, for solar driven hydrogen production, such as: electrochemical, photochemical and thermochemical process. Furthermore, the paper presents an analysis of those technologies from a technical as well as economic point of view. In addition, the paper aims to draw attention to the fact that the generation of hydrogen using renewable energy should be imposed as a logical and proper way to store solar energy in the form of chemical energy.

  17. Recent review of thermochemical hydrogen production

    Science.gov (United States)

    Beghi, G. E.

    A survey is presented on the development to date of thermochemical water decomposition methods for the production of hydrogen. It is shown that: (1) both the technological feasibility of thermochemical processes and their competitiveness with water electrolysis have been demonstrated; (2) the scaling up of thermochemical methods to industrial production levels may proceed with existing technology; (3) the slowing down of programs concerned with the development of high temperature nuclear reactors could delay the scaling up of thermochemical hydrogen production to industrial levels; (4) this delay could, however, increase interest in such water decomposition processes as those employing photoreactions; and (5) the efficiency of thermochemical hydrogen production is highest in the case of systems with dedicated heat sources rated above 1000 MWth.

  18. Gaseous hydrogen production by water dissociation method

    Energy Technology Data Exchange (ETDEWEB)

    Lipovetsky, V.

    2003-04-01

    Gaseous hydrogen production is based on employment of the water dissociation process, intensified by action of a high water temperature and increase of the minus electric field, as a factor for water dissociation instead of electric current used in electrolysis. The water dissociation method makes it possible to produce concurrently both gaseous hydrogen and electric power in the operating reactor. The main power type used is thermal. (Author)

  19. Microbial consortia for hydrogen production enhancement.

    Science.gov (United States)

    Rajhi, Haifa; Díaz, Emiliano E; Rojas, Patricia; Sanz, José L

    2013-07-01

    Ten efficient hydrogen-producing strains affiliated to the Clostridium genus were used to develop consortia for hydrogen production. In order to determine their saccharolytic and proteolytic activities, glucose and meat extract were tested as fermentation substrates, and the best hydrogen-producing strains were selected. The C. roseum H5 (glucose-consuming) and C. butyricum R4 (protein-degrading) co-culture was the best hydrogen-producing co-culture. The end-fermentation products for the axenic cultures and co-cultures were analyzed. In all cases, organic acids, mainly butyrate and acetate, were produced lowering the pH and thus inhibiting further hydrogen production. In order to replace the need for reducing agents for the anaerobic growth of clostridia, a microbial consortium including Clostridium spp. and an oxygen-consuming microorganism able to form dense granules (Streptomyces sp.) was created. Increased yields of hydrogen were achieved. The effect of adding a butyrate-degrading bacteria and an acetate-consuming archaea to the consortia was also studied.

  20. Continuous hydrogen production from starch by fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Yasuda, Keigo; Tanisho, Shigeharu [Yokohama National Univ. (Japan)

    2010-07-01

    This study was investigated the effect of hydraulic retention time (HRT) on hydrogen production rate, hydrogen yield and the production rate of volatile fatty acid. The experiment was performed in a continuous stirred tank reactor (CSTR) with a working volume of 1 L by using a Clostridium sp. The temperature of the CSTR was regulated 37 C. The pH was controlled 6.0 by the addition of 3 M of NaOH solution. Starch was used as the carbon source with the concentration of 30 g L{sup -1}. Hydrogen production rate increased from 0.9 L-H{sub 2} L-culture{sup -1} h{sup -1} to 3.2 L-H{sub 2} L-culture{sup -1} h{sup -1} along with the decrease of HRT from 9 h to 1.5 h. Hydrogen yield decreased at low HRT. The major volatile fatty acids are acetic acid, butyric acid and lactic acid. The production rates of acetic acid and butyric acid increased along with the decrease of HRT. On the other hand, the rate of lactic acid was low at high HRT while it increased at HRT 1.5 h. The increase of the production rate of lactic acid suggested one of the reasons that hydrogen yield decreased. (orig.)

  1. Fermentative hydrogen production by diverse microflora

    Energy Technology Data Exchange (ETDEWEB)

    Baghchehsaraee, Bita; Nakhla, George; Karamanev, Dimitre; Margaritis, Argyrios [Department of Chemical and Biochemical Engineering, The University of Western Ontario, London, Ontario N6A 5B9 (Canada)

    2010-05-15

    In this study, hydrogen production with activated sludge, a diverse bacterial source has been investigated and compared to microflora from anaerobic digester sludge, which is less diverse. Batch experiments were conducted at mesophilic (37 C) and thermophilic (55 C) temperatures. The hydrogen production yields with activated sludge at 37 C and 55 C were 0.56 and 1.32 mol H{sub 2}/mol glucose consumed, respectively. While with anaerobically digested sludge hydrogen yield was 2.18 mol H{sub 2}/mol glucose consumed at 37 C and 1.25 mol H{sub 2}/mol glucose consumed at 55 C. The results of repeated batch experiments for 615 h resulted in average yields of 1.21 {+-} 0.62 and 1.40 {+-} 0.16 mol H{sub 2}/mol glucose consumed for activated sludge and anaerobic sludge, respectively. The hydrogen production with activated sludge was not stable during the repeated batches and the fluctuation in hydrogen production was attributed to formation of lactic acid as the predominant metabolite in some batches. The presence of lactic acid bacteria in microflora was confirmed by PCR-DGGE. (author)

  2. Systematic Discrimination of Advanced Hydrogen Production Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Charles V. Park; Michael W. Patterson

    2010-07-01

    The U.S. Department of Energy, in concert with industry, is developing a high-temperature gas-cooled reactor at the Idaho National Laboratory (INL) to demonstrate high temperature heat applications to produce hydrogen and electricity or to support other industrial applications. A key part of this program is the production of hydrogen from water that would significantly reduce carbon emissions compared to current production using natural gas. In 2009 the INL led the methodical evaluation of promising advanced hydrogen production technologies in order to focus future resources on the most viable processes. This paper describes how the evaluation process was systematically planned and executed. As a result, High-Temperature Steam Electrolysis was selected as the most viable near-term technology to deploy as a part of the Next Generation Nuclear Plant Project.

  3. Production of pure hydrogen by ethanol dehydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Santacesaria, E.; Carotenuto, G.; Tesser, R.; Di Serio, M. [Naples ' ' Federico II' ' Univ. (Italy). Dept. of Chemistry

    2010-12-30

    Hydrogen production from bio-ethanol is one of the most promising renewable processes to generate electricity using fuel cells. In this work, we have studied the production of pure hydrogen as by product of ethanol dehydrogenation reaction. This reaction is promoted by copper based catalysts and according to the catalyst used and the operative conditions gives place to acetaldehyde or ethyl acetate as main products. We studied in particular the performance of a commercial copper/copper chromite catalyst, supported on alumina and containing barium chromate as promoter that has given the best results. By operating at low pressure and temperature with short residence times, acetaldehyde is more selectively produced, while, by increasing the pressure (10-30 bars), the temperature (200-260 C) and the residence time (about 100 (grams hour/mol) of ethanol contact time) the selectivity is shifted to the production of ethyl acetate. However, in both cases pure hydrogen is obtained, as by product, that can easily be separated. Hydrogen obtained in this way is exempt of CO and can be directly fed to fuel cells without any inconvenience. In this work, runs performed in different operative conditions have been reported with the scope to individuate the best conditions. A carrier of H{sub 2} 6% in N{sub 2} has been used. The studied catalyst has also shown a good thermal stability with respect to sintering phenomena, that generally occurs during the dehydrogenation on other copper catalysts. Hydrogen productivities of 8-39 mol{sub H2} (gcat){sup -1}(h){sup -1} have been obtained for the explored temperature range 200-260 C. At last, the most accredited reaction mechanism is reported and discussed on the basis of the obtained results. (orig.)

  4. Catalytic carbon membranes for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Damle, A.S.; Gangwal, S.K.

    1992-01-01

    Commercial carbon composite microfiltration membranes may be modified for gas separation applications by providing a gas separation layer with pores in the 1- to 10-nm range. Several organic polymeric precursors and techniques for depositing a suitable layer were investigated in this project. The in situ polymerization technique was found to be the most promising, and pure component permeation tests with membrane samples prepared with this technique indicated Knudsen diffusion behavior. The gas separation factors obtained by mixed-gas permeation tests were found to depend strongly on gas temperature and pressure indicating significant viscous flow at high-pressure conditions. The modified membranes were used to carry out simultaneous water gas shift reaction and product hydrogen separation. These tests indicated increasing CO conversions with increasing hydrogen separation. A simple process model was developed to simulate a catalytic membrane reactor. A number of simulations were carried out to identify operating conditions leading to product hydrogen concentrations over 90 percent. (VC)

  5. Hydrogen production by alkaline water electrolysis

    Directory of Open Access Journals (Sweden)

    Diogo M. F. Santos

    2013-01-01

    Full Text Available Water electrolysis is one of the simplest methods used for hydrogen production. It has the advantage of being able to produce hydrogen using only renewable energy. To expand the use of water electrolysis, it is mandatory to reduce energy consumption, cost, and maintenance of current electrolyzers, and, on the other hand, to increase their efficiency, durability, and safety. In this study, modern technologies for hydrogen production by water electrolysis have been investigated. In this article, the electrochemical fundamentals of alkaline water electrolysis are explained and the main process constraints (e.g., electrical, reaction, and transport are analyzed. The historical background of water electrolysis is described, different technologies are compared, and main research needs for the development of water electrolysis technologies are discussed.

  6. Hydrogen production by fermentative consortia

    Energy Technology Data Exchange (ETDEWEB)

    Valdez-Vazquez, Idania [Centro de Investigacion Cientifica y de Educacion Superior de Ensenada (CICESE), Department of Marine Biotechnology, Ensenada, B.C. Mexico (Mexico); Poggi-Varaldo, Hector M. [CINVESTAV-IPN, Department of Biotechnology and Bioengineering, PO Box 14-740, Mexico D.F. 07000 (Mexico)

    2009-06-15

    In this work, H{sub 2} production by anaerobic mixed cultures was reviewed. First, the different anaerobic microbial communities that have a direct relation with the generation or consumption of H{sub 2} are discussed. Then, the different methods used to inhibit the H{sub 2}-consuming bacteria are analyzed (mainly in the methanogenesis phase) such as biokinetic control (low pH and short hydraulic retention time), heat-shock treatment and chemical inhibitors along with their advantages/disadvantages for their application on an industrial scale. After that, biochemical pathways of carbohydrate degradation to H{sub 2}, organic acids and solvents are showed. Fourth, structure, diversity and dynamics of H{sub 2}-producers communities are detailed. Later, the hydrogenase structure and activity is related with H{sub 2} production. Also, the causes for H{sub 2} production inhibition are analyzed along with strategies to avoid it. Finally, immobilized-cells systems are presented as a way to enhance H{sub 2} production. (author)

  7. Strength of hydrogen bonds of water depends on local environment.

    Science.gov (United States)

    Huš, Matej; Urbic, Tomaz

    2012-04-14

    In-depth knowledge of water-water potential is important for devising and evaluating simple water models if they are to accurately describe water properties and reflect various solvation phenomena. Water-water potential depends upon inter-molecular distance, relative orientation of water molecules, and also local environment. When placed at a favorable distance in a favorable orientation, water molecules exhibit a particularly strong attractive interaction called hydrogen bond. Although hydrogen bond is very important for its effects on the elements of life, industrial applications, and bulk water properties, there is no scientific consensus on its true nature and origin. Using quantum-mechanical methods, hydrogen bond strength was calculated in different local environments. A simple empirical linear relationship was discovered between maximum hydrogen bond strength and the number of water molecules in the local environment. The local environment effect was shown to be considerable even on the second coordination shell. Additionally, a negative linear correlation was found between maximum hydrogen bond strength and the distance, at which it was observed. These results provide novel insights into the nature of hydrogen bonding.

  8. Electricity-mediated biological hydrogen production

    NARCIS (Netherlands)

    Geelhoed, J.S.; Hamelers, H.V.M.; Stams, A.J.M.

    2010-01-01

    Anaerobic bacteria have the ability to produce electricity from the oxidation of organic substrates. They also may use electricity to support chemical reactions that are energetically unfavorable. In the fermentation of sugars, hydrogen can be formed as one of the main products. However, a yield of

  9. Reactors Save Energy, Costs for Hydrogen Production

    Science.gov (United States)

    2014-01-01

    While examining fuel-reforming technology for fuel cells onboard aircraft, Glenn Research Center partnered with Garrettsville, Ohio-based Catacel Corporation through the Glenn Alliance Technology Exchange program and a Space Act Agreement. Catacel developed a stackable structural reactor that is now employed for commercial hydrogen production and results in energy savings of about 20 percent.

  10. Hydrogen production by cynobacteria in microemulsion

    Energy Technology Data Exchange (ETDEWEB)

    Famiglietti Michel, M.

    1992-01-01

    The first part of the present study investigates the solubilization and photosynthetic activity of filamentous, heterocystous cynobacteria (Anabaena variabilis) in water-in-oil microemulsions. Transparent microemulsions containing up to 10[sup 8] cells/ml were obtained. The physical state of the cells in the organic milieu, which was analyzed by light and electron microscopy, is dependent on the hydrophilic-lipophilic balance (HLB) of the system. Cell solubilization in microemulsions is observed only at HLB values higher than 9, where the filaments are homogeneously dispersed in the organic milieu. Solubilized cells display clear photosynthetic activity in (Tween 85/Span 80)/hexadecane/water at w[sub o] > 30 and 86 mM total surfactant concentration. Photosynthetic activity is assessed by measuring oxygen evolution with a Clark electrode, directly immersed in the microemulsion. Under illumination 0.53 [mu]mol O[sub 2]/min x mg Chl a are produced, while in the dark oxygen consumption occurs, due to respiration. Oxygen evolution is clearly a result of photosynthetic activity: no oxygen is produced in the presence of specific inhibitors of photosynthesis. The second part of this study focuses on the capacity of A. variabilis to produce hydrogen. Hydrogen production is not obtained in Tween 85/Span 80/hexadecane/water. In contrast, addition of Tween to aqueous suspensions of cynobacterial cells induces a significant hydrogen release. The amount of hydrogen evolved, depends on the chemical structure of the surfactant. Varied degrees of activity are shown by Tween, the most active surfactant being Tween 85. About 5 ml of hydrogen are released by A. variabilis in 10% Tween 85/growth medium, under anaerobic conditions, over a time span of 28 days. In the control sample, in growth medium, only 0.073 ml of hydrogen are produced in the same time-interval. Furthermore, in the presence of Tween 85, hydrogen production can be observed for at least two months.

  11. Photobiological hydrogen production employing Spirulina Maxima

    Energy Technology Data Exchange (ETDEWEB)

    Ugas, A.J.; Sebastian, P.J. [CIE-UNAM, Morelos (Mexico); Duhakt, R.V.; Valencia, R.T. [IBT-UNAM, Cuernavaca, Morelos (Mexico)

    2003-07-01

    Efforts are being made to develop materials and processes for the renewable production of hydrogen. This paper described the biological production of hydrogen using microorganisms via the photosynthetic route. Several experiments were conducted to produce hydrogen from the biomass of a strain of photosynthetic Spirulina maxim. Conductimetry was used to quantify the results, along with its introduction in a proton exchange membrane (PEM) fuel cell. The current generated was then measured. Spirulina maxim was cultivated under illumination by magnetic agitation air bubbling. The biomass was concentrated by filtration with micro-porous nylon cloth. The algal biomass was quantified by dry weight and by spectrophotometry. The biomass underwent an anaerobic process in darkness, under a nitrogen flow for 30 minutes. The photosynthesis reaction and the production of the enzyme hydrogenase were induced by leaving the culture in agitation and under illumination for 30 minutes to 2 hours. Tests were conducted with and without the addition of 2 grams of sodium ditionite before the photosynthesis process and with the same incident radiation in the bioreactor, which was coupled to a PEM fuel cell. The electric current generated was measured. The results indicate that after a certain stage of cellular growth, Spirulina maxim was capable of producing hydrogen photosynthetically after a process of anaerobic darkness. The biological production of hydrogen was quantifiable by conductimetry and coupling the bioreactor to a PEM fuel cell. The sodium ditionite proved to be a strong reducing agent that inhibits the oxygen production during the photosynthesis process and allows the activation of the enzyme hydrogenase. 4 refs., 2 tabs.

  12. Catalytic glycerol steam reforming for hydrogen production

    Science.gov (United States)

    Dan, Monica; Mihet, Maria; Lazar, Mihaela D.

    2015-12-01

    Hydrogen production from glycerol by steam reforming combine two major advantages: (i) using glycerol as raw material add value to this by product of bio-diesel production which is obtained in large quantities around the world and have a very limited utilization now, and (ii) by implication of water molecules in the reaction the efficiency of hydrogen generation is increased as each mol of glycerol produces 7 mol of H2. In this work we present the results obtained in the process of steam reforming of glycerol on Ni/Al2O3. The catalyst was prepared by wet impregnation method and characterized through different methods: N2 adsorption-desorption, XRD, TPR. The catalytic study was performed in a stainless steel tubular reactor at atmospheric pressure by varying the reaction conditions: steam/carbon ratio (1-9), gas flow (35 ml/min -133 ml/min), temperature (450-650°C). The gaseous fraction of the reaction products contain: H2, CH4, CO, CO2. The optimum reaction conditions as resulted from this study are: temperature 550°C, Gly:H2O ratio 9:1 and Ar flow 133 ml/min. In these conditions the glycerol conversion to gaseous products was 43% and the hydrogen yield was 30%.

  13. Catalytic glycerol steam reforming for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Dan, Monica, E-mail: monica.dan@itim-cj.ro; Mihet, Maria, E-mail: maria.mihet@itim-cj.ro; Lazar, Mihaela D., E-mail: diana.lazar@itim-cj.ro [National Institute for Research and Development of Isotopic and Molecular Technologies, 67-103 Donat Street, 400293 Cluj Napoca (Romania)

    2015-12-23

    Hydrogen production from glycerol by steam reforming combine two major advantages: (i) using glycerol as raw material add value to this by product of bio-diesel production which is obtained in large quantities around the world and have a very limited utilization now, and (ii) by implication of water molecules in the reaction the efficiency of hydrogen generation is increased as each mol of glycerol produces 7 mol of H{sub 2}. In this work we present the results obtained in the process of steam reforming of glycerol on Ni/Al{sub 2}O{sub 3}. The catalyst was prepared by wet impregnation method and characterized through different methods: N{sub 2} adsorption-desorption, XRD, TPR. The catalytic study was performed in a stainless steel tubular reactor at atmospheric pressure by varying the reaction conditions: steam/carbon ratio (1-9), gas flow (35 ml/min -133 ml/min), temperature (450-650°C). The gaseous fraction of the reaction products contain: H{sub 2}, CH{sub 4}, CO, CO{sub 2}. The optimum reaction conditions as resulted from this study are: temperature 550°C, Gly:H{sub 2}O ratio 9:1 and Ar flow 133 ml/min. In these conditions the glycerol conversion to gaseous products was 43% and the hydrogen yield was 30%.

  14. Assessment of biological Hydrogen production processes: A review

    Science.gov (United States)

    Najafpour, G. D.; Shahavi, M. H.; Neshat, S. A.

    2016-06-01

    Energy crisis created a special attention on renewable energy sources. Among these sources; hydrogen through biological processes is well-known as the most suitable and renewable energy sources. In terms of process yield, hydrogen production from various sources was evaluated. A summary of microorganisms as potential hydrogen producers discussed along with advantages and disadvantages of several bioprocesses. The pathway of photo-synthetic and dark fermentative organisms was discussed. In fact, the active enzymes involved in performance of biological processes for hydrogen generation were identified and their special functionalities were discussed. The influential factors affecting on hydrogen production were known as enzymes assisting liberation specific enzymes such as nitrogenase, hydrogenase and uptake hydrogenase. These enzymes were quite effective in reduction of proton and form active molecular hydrogen. Several types of photosynthetic systems were evaluated with intension of maximum hydrogen productivities. In addition dark fermentative and light intensities on hydrogen productions were evaluated. The hydrogen productivities of efficient hydrogen producing strains were evaluated.

  15. Bioaugmentation of biogas production by a hydrogen-producing bacterium.

    Science.gov (United States)

    Ács, Norbert; Bagi, Zoltán; Rákhely, Gábor; Minárovics, János; Nagy, Katalin; Kovács, Kornél L

    2015-06-01

    The rate-limiting nature of the hydrogen concentration prevailing in the anaerobic digester has been recognized, but the associated alterations in the microbial community are unknown. In response to the addition of Enterobacter cloacae cells in laboratory anaerobic digesters, the level of biogas production was augmented. Terminal restriction fragment length polymorphism (T-RFLP) and real-time polymerase chain reaction (Real-Time PCR) were used to study the survival of mesophilic hydrogen-producing bacteria and the effects of their presence on the composition of the other members of the bacterial community. E. cloacae proved to maintain a stable cell number and to influence the microbial composition of the system. Bioaugmentation by a single strain added to the natural biogas-producing microbial community was demonstrated. The community underwent pronounced changes as a result of the relatively slight initial shift in the microbiological system, responding sensitively to the alterations in local hydrogen concentration.

  16. Hydrogen Production from Ammonia Using a Plasma Membrane Reactor

    Directory of Open Access Journals (Sweden)

    Shinji Kambara

    2016-06-01

    Full Text Available In this study, an efficient method for using pulsed plasma to produce hydrogen from ammonia was developed. An original pulsed plasma reactor with a hydrogen separation membrane was developed for efficient hydrogen production, and its hydrogen production performance was investigated. Hydrogen production in the plasma was affected by the applied voltage and flow rate of ammonia gas. The maximum hydrogen production flow rate of a typical plasma reactor was 8.7 L/h, whereas that of the plasma membrane reactor was 21.0 L/h. We found that ammonia recombination reactions in the plasma controlled hydrogen production in the plasma reactor. In the plasma membrane reactor, a significant increase in hydrogen production was obtained because ammonia recombination reactions were inhibited by the permeation of hydrogen radicals generated in the plasma through a palladium alloy membrane. The energy efficiency was 4.42 mol-H2/kWh depending on the discharge power.

  17. Economical hydrogen production by electrolysis using nano pulsed DC

    OpenAIRE

    Dharmaraj C.H, AdishKumar S.

    2012-01-01

    Hydrogen is an alternate renewable eco fuel. The environmental friendly hydrogen production method is electrolysis. The cost of electrical energy input is major role while fixing hydrogen cost in the conventional direct current Electrolysis. Using nano pulse DC input make the input power less and economical hydrogen production can be established. In this investigation, a lab scale electrolytic cell developed and 0.58 mL/sec hydrogen/oxygen output is obtained using conventional and nano pulsed...

  18. Study on commercial HTGR hydrogen production system

    Energy Technology Data Exchange (ETDEWEB)

    Nishihara, Tetsuo [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Hada, Kazuhiko [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment; Nishimura, Kuniyuki [Mitsubishi Research Institute, Tokyo (Japan)

    2000-07-01

    The Japanese energy demand in 2030 will increase up to 117% in comparison with one in 2000. We have to avoid a large consumption of fossil fuel that induces a large CO{sub 2} emission from viewpoint of global warming. Furthermore new energy resources expected to resolve global warming have difficulty to be introduced more because of their low energy density. As a result, nuclear power still has a possibility of large introduction to meet the increasing energy demand. On the other hand, in Japan, 40% of fossil fuels in the primary energy are utilized for power generation, and the remaining are utilized as a heat source. New clean energy is required to reduce the consumption of fossil fuels and hydrogen is expected as a alternative energy resource. Prediction of potential hydrogen demand in Japan is carried out and it is clarified that the demand will potentially increase up to 4% of total primary energy in 2050. In present, steam reforming method is the most economical among hydrogen generation processes and the cost of hydrogen production is about 7 to 8 yen/m{sup 3} in Europe and the United States and about 13 yen/m{sup 3} in Japan. JAERI has proposed for using the HTGR whose maximum core outlet temperature is at 950degC as a heat source in the steam reforming to reduced the consumption of fossil fuels and resulting CO{sub 2} emission. Based on the survey of the production rate and the required thermal energy in conventional industry, it is clarified that a hydrogen production system by the steam reforming is the best process for the commercial HTGR nuclear heat utilization. The HTGR steam reforming system and other candidate nuclear heat utilization systems are considered from viewpoint of system layout and economy. From the results, the hydrogen production cost in the HTGR stream reforming system is expected to be about 13.5 yen/m{sup 3} if the cost of nuclear heat of the HTGR is the same as one of the LWR. (author)

  19. Dynamical localization: Hydrogen atoms in magnetic and microwave fields

    Energy Technology Data Exchange (ETDEWEB)

    Benvenuto, F.; Casati, G. [Dipartimento di Fisica dellUniversita, Via Castelnuovo 7, 22100 Como (Italy); Shepelyansky, D.L. [Laboratoire de Physique Quantique, UMR C5626 du CNRS, Universite Paul Sabatier, 31062, Toulouse (France)

    1997-03-01

    We show that dynamical localization for excited hydrogen atoms in magnetic and microwave fields takes place at quite low microwave frequency ({omega}n{sup 3}{lt}1). Estimates of the localization length are given for different parameter regimes, showing that the quantum delocalization border drops significantly as compared to the case of zero magnetic field. This opens up broad possibilities for laboratory investigations. {copyright} {ital 1997} {ital The American Physical Society}

  20. Hydrogen Production from Methanol Using Corona Discharges

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Hydrogen production at room temperature from liquid methanol has been conductedusing corona discharge. The content of water in methanol solution has a significant effect on thisproduction. When water concentration increases from 1.0 % to 16.7 %, the methanol conversionrate changes from 0.196 to 0.284 mol/h. An important finding in this investigation is theformation of ethylene glycol as a major by-product. The yield of ethylene glycol is ranged from0.0045 to 0.0075 mol/h based on the water content.

  1. A Technical and Economic Review of Solar Hydrogen Production Technologies

    Science.gov (United States)

    Wilhelm, Erik; Fowler, Michael

    2006-01-01

    Hydrogen energy systems are being developed to replace fossil fuels-based systems for transportation and stationary application. One of the challenges facing the widespread adoption of hydrogen as an energy vector is the lack of an efficient, economical, and sustainable method of hydrogen production. In the short term, hydrogen produced from…

  2. Integrated Ceramic Membrane System for Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Schwartz, Joseph; Lim, Hankwon; Drnevich, Raymond

    2010-08-05

    Phase I was a technoeconomic feasibility study that defined the process scheme for the integrated ceramic membrane system for hydrogen production and determined the plan for Phase II. The hydrogen production system is comprised of an oxygen transport membrane (OTM) and a hydrogen transport membrane (HTM). Two process options were evaluated: 1) Integrated OTM-HTM reactor – in this configuration, the HTM was a ceramic proton conductor operating at temperatures up to 900°C, and 2) Sequential OTM and HTM reactors – in this configuration, the HTM was assumed to be a Pd alloy operating at less than 600°C. The analysis suggested that there are no technical issues related to either system that cannot be managed. The process with the sequential reactors was found to be more efficient, less expensive, and more likely to be commercialized in a shorter time than the single reactor. Therefore, Phase II focused on the sequential reactor system, specifically, the second stage, or the HTM portion. Work on the OTM portion was conducted in a separate program. Phase IIA began in February 2003. Candidate substrate materials and alloys were identified and porous ceramic tubes were produced and coated with Pd. Much effort was made to develop porous substrates with reasonable pore sizes suitable for Pd alloy coating. The second generation of tubes showed some improvement in pore size control, but this was not enough to get a viable membrane. Further improvements were made to the porous ceramic tube manufacturing process. When a support tube was successfully coated, the membrane was tested to determine the hydrogen flux. The results from all these tests were used to update the technoeconomic analysis from Phase I to confirm that the sequential membrane reactor system can potentially be a low-cost hydrogen supply option when using an existing membrane on a larger scale. Phase IIB began in October 2004 and focused on demonstrating an integrated HTM/water gas shift (WGS) reactor to

  3. Kinetic models for fermentative hydrogen production: A review

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jianlong; Wan, Wei [Laboratory of Environmental Technology, INET, Tsinghua University, Beijing 100084 (China)

    2009-05-15

    The kinetic models were developed and applied for fermentative hydrogen production. They were used to describe the progress of a batch fermentative hydrogen production process, to investigate the effects of substrate concentration, inhibitor concentration, temperatures, pH, and dilution rates on the process of fermentative hydrogen production, and to establish the relationship among the substrate degradation rate, the hydrogen-producing bacteria growth rate and the product formation rate. This review showed that the modified Gompertz model was widely used to describe the progress of a batch fermentative hydrogen production process, while the Monod model was widely used to describe the effects of substrate concentration on the rates of substrate degradation, hydrogen-producing bacteria growth and hydrogen production. Arrhenius model was used a lot to describe the effects of temperature on fermentative hydrogen production, while modified Han-Levenspiel model was used to describe the effects of inhibitor concentration on fermentative hydrogen production. The Andrew model was used to describe the effects of H{sup +} concentration on the specific hydrogen production rate, while the Luedeking-Piret model and its modified form were widely used to describe the relationship between the hydrogen-producing bacteria growth rate and the product formation rate. Finally, some suggestions for future work with these kinetic models were proposed. (author)

  4. Resource Assessment for Hydrogen Production: Hydrogen Production Potential from Fossil and Renewable Energy Resources

    Energy Technology Data Exchange (ETDEWEB)

    Melaina, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Penev, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Heimiller, D. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2013-09-01

    This study examines the energy resources required to produce 4-10 million metric tonnes of domestic, low-carbon hydrogen in order to fuel approximately 20-50 million fuel cell electric vehicles. These projected energy resource requirements are compared to current consumption levels, projected 2040 business as usual consumptions levels, and projected 2040 consumption levels within a carbonconstrained future for the following energy resources: coal (assuming carbon capture and storage), natural gas, nuclear (uranium), biomass, wind (on- and offshore), and solar (photovoltaics and concentrating solar power). The analysis framework builds upon previous analysis results estimating hydrogen production potentials and drawing comparisons with economy-wide resource production projections

  5. Hydrogen production from glucose in ionic liquids

    Energy Technology Data Exchange (ETDEWEB)

    Assenbaum, D.W.; Taccardi, N.; Berger, M.E.M.; Boesmann, A.; Enzenberger, F.; Woelfel, R.; Wasserscheid, P. [Erlangen-Nuernberg Univ. (Germany). Lehrstuhl fuer chemische Reaktionstechnik

    2010-07-01

    Depletion of oil and gas reserves and growing global warming concerns have created a world-wide interest in new concepts for future sustainable energy supplies. The development of effective ways to produce hydrogen from biomass is expected to be one important contribution to such a goal [1]. Nowadays, three main processes are considered for future industrial application, namely: gasification of biomass [2], reforming in supercritical water [3] and aqueous phase reforming [4,5]. Other technologies such as enzymatic decomposition of sugars or steam reforming of bio-oils suffer from low hydrogen production rates and/or complex processing requirements and can probably not be considered for industrial applications in the closer future [6,7]. On the other hand, either the gasification of biomass, which is typically carried out at temperatures above 800 C using Ni or Fe catalysts [8,9,10,11], or the reforming in supercritical water, which is typically carried out in presence of Ru catalyst at pressures of 300bar and temperatures ranging from 500 to 700 C [12], suffer of poor energetic efficiency as a lot of energy is required to run the reactions. More recently, an alternative to the two aforementioned high temperature processes has been proposed as ''aqueous phase reforming'' (APR) by Dumesic and coworkers [13,14,15,16,17]. They achieved the reforming of polyols (such as ethylene glycol, glycerol and sorbitol) using heterogeneous catalysts at temperatures between 200 and 250 C and pressure typically between 15-50bar.The temperature level of the reaction allows generating hydrogen with low amounts of CO in a single reactor. The process typically forms 35 % of hydrogen, 40 % of CO2 and 25 % of combined alkanes. The high amount of formed alkanes originates eventually from CO hydrogenation and Fischer-Tropsch (F-T) reaction [18,19,20,21], those are thermodynamically favored in the above mentioned conditions. However, heterogeneously catalyzed APR

  6. Development of Local Chicken Production Based on Local Feed Ingredients

    Directory of Open Access Journals (Sweden)

    Cecep Hidayat

    2012-06-01

    Full Text Available Development of local chicken production based on local feed ingredient is in line with the vision of Indonesian goverment to fulfill meat and egg national requirement based on local resources. There are two big problem which become stumblingblock in developing local chicken production. The first problem is the difficulty to get day old chick of local chicken. This problem can be solved by integrating breeder institutions belong to goverment with research institution and with local chicken producer association. The second problem is the low performance of local chicken. To improve local chicken performance, it can be done by improving the breed, feed and management. Several research results show that good performance of local chicken were obtained by inclusion of local feed ingredients in the ration. Therefore, development of local chicken production based an local feed resources can be applied.

  7. Hydrogen Research for Spaceport and Space-Based Applications: Hydrogen Production, Storage, and Transport. Part 3

    Science.gov (United States)

    Anderson, Tim; Balaban, Canan

    2008-01-01

    The activities presented are a broad based approach to advancing key hydrogen related technologies in areas such as fuel cells, hydrogen production, and distributed sensors for hydrogen-leak detection, laser instrumentation for hydrogen-leak detection, and cryogenic transport and storage. Presented are the results from research projects, education and outreach activities, system and trade studies. The work will aid in advancing the state-of-the-art for several critical technologies related to the implementation of a hydrogen infrastructure. Activities conducted are relevant to a number of propulsion and power systems for terrestrial, aeronautics and aerospace applications. Hydrogen storage and in-space hydrogen transport research focused on developing and verifying design concepts for efficient, safe, lightweight liquid hydrogen cryogenic storage systems. Research into hydrogen production had a specific goal of further advancing proton conducting membrane technology in the laboratory at a larger scale. System and process trade studies evaluated the proton conducting membrane technology, specifically, scale-up issues.

  8. Electrocatalysis research for fuel cells and hydrogen production

    CSIR Research Space (South Africa)

    Mathe, MK

    2012-01-01

    Full Text Available The CSIR undertakes research in the Electrocatalysis of fuel cells and for hydrogen production. The Hydrogen South Africa (HySA) strategy supports research on electrocatalysts due to their importance to the national beneficiation strategy. The work...

  9. Production of hydrogen using an anaerobic biological process

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, Robert; Pelter, Libbie S.; Patterson, John A.

    2016-11-29

    Various embodiments of the present invention pertain to methods for biological production of hydrogen. More specifically, embodiments of the present invention pertain to a modular energy system and related methods for producing hydrogen using organic waste as a feed stock.

  10. Hydrogen production by biological processes: a survey of literature

    Energy Technology Data Exchange (ETDEWEB)

    Das, Debabrata [Indian Inst. of Technology, Dept. of Biotechnology, Kharagpur (India); Miami Univ., Clean Energy Research Inst., Coral Gables, FL (United States); Veziroglu, T. Nejat [Miami Univ., Clean Energy Research Inst., Coral Gables, FL (United States)

    2001-07-01

    Hydrogen is the fuel of the future mainly due to its high conversion efficiency, recyclability and nonpolluting nature. Biological hydrogen production processes are found to be more environment friendly and less energy intensive as compared to thermochemical and electrochemical processes. They are mostly controlled by either photosynthetic or fermentative organisms. Till today, more emphasis has been given on the former processes. Nitrogenase and hydrogenase play very important roles. Genetic manipulation of cyanobacteria (hydrogenase negative gene) improves the hydrogen generation. The paper presents a survey of biological hydrogen production processes. The micro-organism and biochemical pathways involved in hydrogen generation processes are presented in some detail. Several developmental works are discussed. Immobilised system is found suitable for the continuous hydrogen production. About 28% of energy can be recovered in the form of hydrogen using sucrose as substrate. Fermentative hydrogen production processes have some edge over the other biological processes. (Author)

  11. Production of hydrogen from municipal solid waste

    Energy Technology Data Exchange (ETDEWEB)

    Coleman, S.L.

    1995-11-01

    The Gasification of Municipal Solid Waste (MSW) includes gasification and the process for producing a gasificable slurry from raw MSW by using high pressures of steam. A potential energy source, MSW is a composite of organic materials such as: paper, wood, food waste, etc. There are different paper grades producing different results with low-quality paper forming better slurries than high-quality papers; making MSW a difficult feedstock for gasification. The objective of the bench-scale laboratory work has been to establish operating conditions for a hydrothermal pre-processing scheme for municipal solid waste (MSW) that produces a good slurry product that can be pumped and atomized to the gasifier for the production of hydrogen. Batch reactors are used to determine product yields as a function of hydrothermal treatment conditions. Various ratios of water-to-paper were used to find out solid product, gas product, and soluble product yields of MSW. Experimental conditions covered were temperature, time, and water to feed ratio. Temperature had the strongest effect on product yields.

  12. Plasma processing methods for hydrogen production

    Science.gov (United States)

    Mizeraczyk, Jerzy; Jasiński, Mariusz

    2016-08-01

    In the future a transfer from the fossil fuel-based economy to hydrogen-based economy is expected. Therefore the development of systems for efficient H2 production becomes important. The several conventional methods of mass-scale (or central) H2 production (methane, natural gas and higher hydrocarbons reforming, coal gasification reforming) are well developed and their costs of H2 production are acceptable. However, due to the H2 transport and storage problems the small-scale (distributed) technologies for H2 production are demanded. However, these new technologies have to meet the requirement of producing H2 at a production cost of (1-2)/kg(H2) (or 60 g(H2)/kWh) by 2020 (the U.S. Department of Energy's target). Recently several plasma methods have been proposed for the small-scale H2 production. The most promising plasmas for this purpose seems to be those generated by gliding, plasmatron and nozzle arcs, and microwave discharges. In this paper plasma methods proposed for H2 production are briefly described and critically evaluated from the view point of H2 production efficiency. The paper is aiming at answering a question if any plasma method for the small-scale H2 production approaches such challenges as the production energy yield of 60 g(H2)/kWh, high production rate, high reliability and low investment cost. Contribution to the topical issue "6th Central European Symposium on Plasma Chemistry (CESPC-6)", edited by Nicolas Gherardi, Ester Marotta and Cristina Paradisi

  13. Biological hydrogen production using a membrane bioreactor.

    Science.gov (United States)

    Oh, Sang-Eun; Iyer, Prabha; Bruns, Mary Ann; Logan, Bruce E

    2004-07-01

    A cross-flow membrane was coupled to a chemostat to create an anaerobic membrane bioreactor (MBR) for biological hydrogen production. The reactor was fed glucose (10,000 mg/L) and inoculated with a soil inoculum heat-treated to kill non-spore-forming methanogens. Hydrogen gas was consistently produced at a concentration of 57-60% in the headspace under all conditions. When operated in chemostat mode (no flow through the membrane) at a hydraulic retention time (HRT) of 3.3 h, 90% of the glucose was removed, producing 2200 mg/L of cells and 500 mL/h of biogas. When operated in MBR mode, the solids retention time (SRT) was increased to SRT = 12 h producing a solids concentration in the reactor of 5800 mg/L. This SRT increased the overall glucose utilization (98%), the biogas production rate (640 mL/h), and the conversion efficiency of glucose-to-hydrogen from 22% (no MBR) to 25% (based on a maximum of 4 mol-H(2)/mol-glucose). When the SRT was increased from 5 h to 48 h, glucose utilization (99%) and biomass concentrations (8,800 +/- 600 mg/L) both increased. However, the biogas production decreased (310 +/- 40 mL/h) and the glucose-to-hydrogen conversion efficiency decreased from 37 +/- 4% to 18 +/- 3%. Sustained permeate flows through the membrane were in the range of 57 to 60 L/m(2) h for three different membrane pore sizes (0.3, 0.5, and 0.8 microm). Most (93.7% to 99.3%) of the membrane resistance was due to internal fouling and the reversible cake resistance, and not the membrane itself. Regular backpulsing was essential for maintaining permeate flux through the membrane. Analysis of DNA sequences using ribosomal intergenic spacer analysis indicated bacteria were most closely related to members of Clostridiaceae and Flexibacteraceae, including Clostridium acidisoli CAC237756 (97%), Linmingia china AF481148 (97%), and Cytophaga sp. MDA2507 AF238333 (99%). No PCR amplification of 16s rRNA genes was obtained when archaea-specific primers were used.

  14. Hydrogen in the Methanol Production Process

    Science.gov (United States)

    Kralj, Anita Kovac; Glavic, Peter

    2006-01-01

    Hydrogen is a very important industrial gas in chemical processes. It is very volatile; therefore, it can escape from the process units and its mass balance is not always correct. In many industrial processes where hydrogen is reacted, kinetics are often related to hydrogen pressure. The right thermodynamic properties of hydrogen can be found for…

  15. Low-Cost Hydrogen Distributed Production System Development

    Energy Technology Data Exchange (ETDEWEB)

    C.E. (Sandy) Thomas, Ph.D., President; Principal Investigator, and

    2011-03-10

    costing approximately $2.87/kg, still above the DOE's 2010 $2.50/kg target. We also began laboratory testing of reforming ethanol, which we showed is currently the least expensive approach to making renewable hydrogen. Extended testing of neat ethanol in micro-reactors was successful, and we also were able to reform E-85 acquired from a local fueling station for 2,700 hours, although some modifications were required to handle the 15% gasoline present in E-85. We began initial tests of a catalyst-coated wall reformer tube that showed some promise in reducing the propensity to coke with E-85. These coated-wall tests ran for 350 hours. Additional resources would be required to commercialize an ethanol reformer operating on E-85, but there is no market for such a product at this time, so this ethanol reformer project was moth-balled pending future government or industry support. The two main objectives of this project were: (1) to design, build and test a steam methane reformer and pressure swing adsorption system that, if scaled up and mass produced, could potentially meet the DOE 2015 cost and efficiency targets for on-site distributed hydrogen generation, and (2) to demonstrate the efficacy of a low-cost renewable hydrogen generation system based on reforming ethanol to hydrogen at the fueling station.

  16. Hydrogen Gas Production from Nuclear Power Plant in Relation to Hydrogen Fuel Cell Technologies Nowadays

    Science.gov (United States)

    Yusibani, Elin; Kamil, Insan; Suud, Zaki

    2010-06-01

    Recently, world has been confused by issues of energy resourcing, including fossil fuel use, global warming, and sustainable energy generation. Hydrogen may become the choice for future fuel of combustion engine. Hydrogen is an environmentally clean source of energy to end-users, particularly in transportation applications because without release of pollutants at the point of end use. Hydrogen may be produced from water using the process of electrolysis. One of the GEN-IV reactors nuclear projects (HTGRs, HTR, VHTR) is also can produce hydrogen from the process. In the present study, hydrogen gas production from nuclear power plant is reviewed in relation to commercialization of hydrogen fuel cell technologies nowadays.

  17. Decentralized and direct solar hydrogen production: Towards a hydrogen economy in MENA region

    Energy Technology Data Exchange (ETDEWEB)

    Bensebaa, Farid; Khalfallah, Mohamed; Ouchene, Majid

    2010-09-15

    Hydrogen has certainly some advantages in spite of its high cost and low efficiency when compared to other energy vectors. Solar energy is an abundant, clean and renewable source of energy, currently competing with fossil fuel for water heating without subsidy. Photo-electrochemical, thermo-chemicals and photo-biological processes for hydrogen production processes have been demonstrated. These decentralised hydrogen production processes using directly solar energy do not require expensive hydrogen infrastructure for packaging and delivery in the short and medium terms. MENA region could certainly be considered a key area for a new start to a global deployment of hydrogen economy.

  18. Nuclear Hydrogen for Peak Electricity Production and Spinning Reserve

    Energy Technology Data Exchange (ETDEWEB)

    Forsberg, C.W.

    2005-01-20

    Nuclear energy can be used to produce hydrogen. The key strategic question is this: ''What are the early markets for nuclear hydrogen?'' The answer determines (1) whether there are incentives to implement nuclear hydrogen technology today or whether the development of such a technology could be delayed by decades until a hydrogen economy has evolved, (2) the industrial partners required to develop such a technology, and (3) the technological requirements for the hydrogen production system (rate of production, steady-state or variable production, hydrogen purity, etc.). Understanding ''early'' markets for any new product is difficult because the customer may not even recognize that the product could exist. This study is an initial examination of how nuclear hydrogen could be used in two interconnected early markets: the production of electricity for peak and intermediate electrical loads and spinning reserve for the electrical grid. The study is intended to provide an initial description that can then be used to consult with potential customers (utilities, the Electric Power Research Institute, etc.) to better determine the potential real-world viability of this early market for nuclear hydrogen and provide the starting point for a more definitive assessment of the concept. If this set of applications is economically viable, it offers several unique advantages: (1) the market is approximately equivalent in size to the existing nuclear electric enterprise in the United States, (2) the entire market is within the utility industry and does not require development of an external market for hydrogen or a significant hydrogen infrastructure beyond the utility site, (3) the technology and scale match those of nuclear hydrogen production, (4) the market exists today, and (5) the market is sufficient in size to justify development of nuclear hydrogen production techniques independent of the development of any other market for hydrogen

  19. Fermentation and Electrohydrogenic Approaches to Hydrogen Production (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Maness, P. C.; Thammannagowda, S.; Magnusson, L.; Logan, B.

    2010-06-01

    This work describes the development of a waste biomass fermentation process using cellulose-degrading bacteria for hydrogen production. This process is then integrated with an electrohydrogenesis process via the development of a microbial electrolysis cell reactor, during which fermentation waste effluent is further converted to hydrogen to increase the total output of hydrogen from biomass.

  20. Hydrogen Production from Hydrogen Sulfide in IGCC Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Elias Stefanakos; Burton Krakow; Jonathan Mbah

    2007-07-31

    IGCC power plants are the cleanest coal-based power generation facilities in the world. Technical improvements are needed to help make them cost competitive. Sulfur recovery is one procedure in which improvement is possible. This project has developed and demonstrated an electrochemical process that could provide such an improvement. IGCC power plants now in operation extract the sulfur from the synthesis gas as hydrogen sulfide. In this project H{sub 2}S has been electrolyzed to yield sulfur and hydrogen (instead of sulfur and water as is the present practice). The value of the byproduct hydrogen makes this process more cost effective. The electrolysis has exploited some recent developments in solid state electrolytes. The proof of principal for the project concept has been accomplished.

  1. A New Hydrogen-Producing Strain and Its Characterization of Hydrogen Production.

    Science.gov (United States)

    Sun, Mingxing; Lv, Yongkang; Liu, Yuxiang

    2015-12-01

    A newly isolated photo non-sulfur (PNS) bacterium was identified as Rhodopseudomonas palustris PB-Z by sequencing of 16S ribosomal DNA (rDNA) genes and phylogenetic analysis. Under vigorous stirring (240 rpm), the hydrogen production performances were greatly improved: The maximum hydrogen production rate and cumulative hydrogen production increased by 188.9 ± 0.07 % and 83.0 ± 0.06 %, respectively, due to the hydrogen bubbles were immediately removed from the culture medium. The effects of different wavelength of light on hydrogen production with stirring were much different from that without stirring. The ranking on the photo-hydrogen production performance was white > yellow > green > blue > red without stirring and white > yellow > blue > red > green under stirring. The best light source for hydrogen production was tungsten filament lamp. The optimum temperature was 35 °C. The maximal hydrogen production rate and cumulative hydrogen production reached 78.7 ± 2.3 ml/l/h and 1728.1 ± 92.7 mol H2/l culture, respectively, under 35 °C, 240 rpm, and illumination of 4000 lux. Pyruvate was one of the main sources of CO2 and has a great impact on the gas composition.

  2. Local doping of graphene devices by selective hydrogen adsorption

    Directory of Open Access Journals (Sweden)

    Min Park

    2015-01-01

    Full Text Available N-type graphene fabricated by exposure to hydrogen gas has been previously studied. Based on this property of graphene, herein, we demonstrate local doping in single-layer graphene using selective adsorption of dissociative hydrogen at 350 K. A graphene field effect transistor was produced covered with PMMA on half of the graphene region. The charge neutrality point of the PMMA-window region shifted to a negative gate voltage (VG region prominently compared with that of the PMMA-covered region. Consequently, a single graphene p-n junction was obtained by measuring the VG-dependent resistance of the whole graphene region. This method presents opportunities for developing and controlling the electronic structure of graphene and device applications.

  3. Solar Thermochemical Hydrogen Production Research (STCH)

    Energy Technology Data Exchange (ETDEWEB)

    Perret, Robert [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2011-05-01

    Eight cycles in a coordinated set of projects for Solar Thermochemical Cycles for Hydrogen production (STCH) were self-evaluated for the DOE-EERE Fuel Cell Technologies Program at a Working Group Meeting on October 8 and 9, 2008. This document reports the initial selection process for development investment in STCH projects, the evaluation process meant to reduce the number of projects as a means to focus resources on development of a few most-likely-to-succeed efforts, the obstacles encountered in project inventory reduction and the outcomes of the evaluation process. Summary technical status of the projects under evaluation is reported and recommendations identified to improve future project planning and selection activities.

  4. Economical hydrogen production by electrolysis using nano pulsed DC

    Directory of Open Access Journals (Sweden)

    Dharmaraj C.H, AdishKumar S.

    2012-01-01

    Full Text Available Hydrogen is an alternate renewable eco fuel. The environmental friendly hydrogen production method is electrolysis. The cost of electrical energy input is major role while fixing hydrogen cost in the conventional direct current Electrolysis. Using nano pulse DC input make the input power less and economical hydrogen production can be established. In this investigation, a lab scale electrolytic cell developed and 0.58 mL/sec hydrogen/oxygen output is obtained using conventional and nano pulsed DC. The result shows that the nano pulsed DC gives 96.8 % energy saving.

  5. Catalytic membrane reactors based on macroporous silicon for hydrogen production

    OpenAIRE

    Vega Bru, Didac; Hernández Díaz, David; López, E. (Eduardo); Jiménez, Nuria; Todorov Trifonov, Trifon; Rodríguez Martínez, Ángel; Alcubilla González, Ramón; Llorca Piqué, Jordi

    2010-01-01

    The typology of using hydrogen as an energy carrier and its implementation in portable fuel cells has motivated a considerable research interest in the development of new efficient hydrogen production technologies. Hydrogen storage and manipulation is however a problematic and hazardous issue. Therefore, the low temperature on-site steam reforming of alcohols for hydrogen supply offers a nice solution to safety and storage issues, while providing several environment advantages […] Peer Rev...

  6. Methods and systems for the production of hydrogen

    Science.gov (United States)

    Oh, Chang H [Idaho Falls, ID; Kim, Eung S [Ammon, ID; Sherman, Steven R [Augusta, GA

    2012-03-13

    Methods and systems are disclosed for the production of hydrogen and the use of high-temperature heat sources in energy conversion. In one embodiment, a primary loop may include a nuclear reactor utilizing a molten salt or helium as a coolant. The nuclear reactor may provide heat energy to a power generation loop for production of electrical energy. For example, a supercritical carbon dioxide fluid may be heated by the nuclear reactor via the molten salt and then expanded in a turbine to drive a generator. An intermediate heat exchange loop may also be thermally coupled with the primary loop and provide heat energy to one or more hydrogen production facilities. A portion of the hydrogen produced by the hydrogen production facility may be diverted to a combustor to elevate the temperature of water being split into hydrogen and oxygen by the hydrogen production facility.

  7. Recent work in advanced hydrogen production concepts

    Science.gov (United States)

    Lawson, D. D.

    1981-03-01

    The hydrogen photoelectrolytic conversion activity investigated the practicability of semiconductor electrolytic devises that use solar energy to decompose water into hydrogen and oxygen in an apparent single step process. The photocatalytic decomposition of inorganic hydrogen compounds; i.e., hydrobromic and hydriodic acids using rhodium organic bridge complexes were also studied. The feasibility of direct high temperature thermal decompositions of water with diffusion processes for separation of the equilibrium mixture of hydrogen and oxygen into usable energy sources was examined.

  8. An Experimental Investigation of Hydrogen Production from Biomass

    Institute of Scientific and Technical Information of China (English)

    吕鹏梅; 常杰; 付严; 王铁军; 陈勇; 祝京旭

    2003-01-01

    In gaseous products of biomass steam gasification, there exist a lot of CO, CH4 and other hydrocarbons that can be converted to hydrogen through steam reforming reactions. There exists potential hydrogen production from the raw gas of biomass steam gasification. In the present work, the characteristics of hydrogen production from biomass steam gasification were investigated in a small-scale fluidized bed. In these experiments, the gasifying agent (air) was supplied into the reactor from the bottom of the reactor and the steam was added into the reactor above biomass feeding location. The effects of reaction temperature, steam to biomass ratio, equivalence ratio (ER) and biomass particle size on hydrogen yield and hydrogen yield potential were investigated. The experimental results showed that higher reactor temperature, proper ER, proper steam to biomass ratio and smaller biomass particle size will contribute to more hydrogen and potential hydrogen yield.

  9. Hydrogen from algal biomass: A review of production process

    Directory of Open Access Journals (Sweden)

    Archita Sharma

    2017-09-01

    Full Text Available Multifariousness of biofuel sources has marked an edge to an imperative energy issue. Production of hydrogen from microalgae has been gathering much contemplation right away. But, mercantile production of microalgae biofuels considering bio-hydrogen is still not practicable because of low biomass concentration and costly down streaming processes. This review has taken up the hydrogen production by microalgae. Biofuels are the up and coming alternative to exhaustible, environmentally and unsafe fossil fuels. Algal biomass has been considered as an enticing raw material for biofuel production, these days photobioreactors and open-air systems are being used for hydrogen production from algal biomass. The formers allow the careful cultivation control whereas the latter ones are cheaper and simpler. A contemporary, encouraging optimization access has been included called algal cell immobilization on various matrixes which has resulted in marked increase in the productivity per volume of a reactor and addition of the hydrogen-production phase.

  10. Hydrogen from algal biomass: A review of production process.

    Science.gov (United States)

    Sharma, Archita; Arya, Shailendra Kumar

    2017-09-01

    Multifariousness of biofuel sources has marked an edge to an imperative energy issue. Production of hydrogen from microalgae has been gathering much contemplation right away. But, mercantile production of microalgae biofuels considering bio-hydrogen is still not practicable because of low biomass concentration and costly down streaming processes. This review has taken up the hydrogen production by microalgae. Biofuels are the up and coming alternative to exhaustible, environmentally and unsafe fossil fuels. Algal biomass has been considered as an enticing raw material for biofuel production, these days photobioreactors and open-air systems are being used for hydrogen production from algal biomass. The formers allow the careful cultivation control whereas the latter ones are cheaper and simpler. A contemporary, encouraging optimization access has been included called algal cell immobilization on various matrixes which has resulted in marked increase in the productivity per volume of a reactor and addition of the hydrogen-production phase.

  11. A microBio reactor for hydrogen production.

    Energy Technology Data Exchange (ETDEWEB)

    Volponi, Joanne V.; Walker, Andrew William

    2003-12-01

    The purpose of this work was to explore the potential of developing a microfluidic reactor capable of enzymatically converting glucose and other carbohydrates to hydrogen. This aggressive project was motivated by work in enzymatic hydrogen production done by Woodward et al. at OWL. The work reported here demonstrated that hydrogen could be produced from the enzymatic oxidation of glucose. Attempts at immobilizing the enzymes resulted in reduced hydrogen production rates, probably due to buffer compatibility issues. A novel in-line sensor was also developed to monitor hydrogen production in real time at levels below 1 ppm. Finally, a theoretical design for the microfluidic reactor was developed but never produced due to the low production rates of hydrogen from the immobilized enzymes. However, this work demonstrated the potential of mimicking biological systems to create energy on the microscale.

  12. Cobalt Ferrite Nanocrystallites for Sustainable Hydrogen Production Application

    Directory of Open Access Journals (Sweden)

    Rajendra S. Gaikwad

    2011-01-01

    Full Text Available Cobalt ferrite, CoFe2O4, nanocrystalline films were deposited using electrostatic spray method and explored in sustainable hydrogen production application. Reflection planes in X-ray diffraction pattern confirm CoFe2O4 phase. The surface scanning microscopy photoimages reveal an agglomeration of closely-packed CoFe2O4 nanoflakes. Concentrated solar-panel, a two-step water splitting process, measurement technique was preferred for measuring the hydrogen generation rate. For about 5 hr sustainable, 440 mL/hr, hydrogen production activity was achieved, confirming the efficient use of cobalt ferrite nanocrystallites film in hydrogen production application.

  13. Substrate and product inhibition of hydrogen production by the extreme thermophile, Caldicellulosiruptor saccharolyticus

    NARCIS (Netherlands)

    Niel, van E.W.J.; Claassen, P.A.M.; Stams, A.J.M.

    2003-01-01

    Substrate and product inhibition of hydrogen production during sucrose fermentation by the extremely thermophilic bacterium Caldicellulosiruptor saccharolyticus was studied. The inhibition kinetics were analyzed with a noncompetitive, nonlinear inhibition model. Hydrogen was the most severe inhibito

  14. Neutral Resonant Ionization in Hydrogen Anion Production

    Science.gov (United States)

    Vogel, John

    2013-09-01

    Dissociative ionization of molecules causes gas phase H- but fails to explain anion intensity. Atomic collisions on surfaces with reduced work function give anions, but also fail to explain intensity, lowered electron density, and diagnostics. Neutral resonant ionization of H(2s) atoms to ion pairs is here predicted with a very high cross section. H(2s,p) atoms are resonant with numerous short-lived excited states (``resonances'') of H- as well as the putative doubly-excited stable state of H- which resists production by other means. This state decays through 1Σu+ (2s σu2) to a singly excited ion pair, leaving both proton and anion with 3.8 eV energy. H(2s,p) atoms arise from dissociative recombination of trihydrogen ion (H3+)which dominates ion content of hydrogen plasmas. Initial H(2s,p) are resonantly produced by ground state Cs atoms or excited Ar, Kr, and Xe atoms, but these initiators are not needed to sustain anion production. This theory may explain the intense ion source at Cal Tech that produced 1.5 mA/cm2 H3 in the mid-1980's (1). A full CRM calculation is not complete, but equilibrium calculations suggest that >1 mA/cm2 H- may be predicted.

  15. EVALUATING HYDROGEN PRODUCTION IN BIOGAS REFORMING IN A MEMBRANE REACTOR

    Directory of Open Access Journals (Sweden)

    F. S. A. Silva

    2015-03-01

    Full Text Available Abstract Syngas and hydrogen production by methane reforming of a biogas (CH4/CO2 = 2.85 using carbon dioxide was evaluated in a fixed bed reactor with a Pd-Ag membrane in the presence of a nickel catalyst (Ni 3.31% weight/γ-Al2O3 at 773 K, 823 K, and 873 K and 1.01×105 Pa. Operation with hydrogen permeation at 873 K increased the methane conversion to approximately 83% and doubled the hydrogen yield relative to operation without hydrogen permeation. A mathematical model was formulated to predict the evolution of the effluent concentrations. Predictions based on the model showed similar evolutions for yields of hydrogen and carbon monoxide at temperatures below 823 K for operations with and without the hydrogen permeation. The hydrogen yield reached approximately 21% at 823 K and 47% at 873 K under hydrogen permeation conditions.

  16. Hydrogen production from water: Recent advances in photosynthesis research

    Energy Technology Data Exchange (ETDEWEB)

    Greenbaum, E.; Lee, J.W. [Oak Ridge National Lab., TN (United States). Chemical Technology Div.

    1997-12-31

    The great potential of hydrogen production by microalgal water splitting is predicated on quantitative measurement of the algae`s hydrogen-producing capability, which is based on the following: (1) the photosynthetic unit size of hydrogen production; (2) the turnover time of photosynthetic hydrogen production; (3) thermodynamic efficiencies of conversion of light energy into the Gibbs free energy of molecular hydrogen; (4) photosynthetic hydrogen production from sea water using marine algae; (5) the potential for research advances using modern methods of molecular biology and genetic engineering to maximize hydrogen production. ORNL has shown that sustained simultaneous photoevolution of molecular hydrogen and oxygen can be performed with mutants of the green alga Chlamydomonas reinhardtii that lack a detectable level of the Photosystem I light reaction. This result is surprising in view of the standard two-light reaction model of photosynthesis and has interesting scientific and technological implications. This ORNL discovery also has potentially important implications for maximum thermodynamic conversion efficiency of light energy into chemical energy by green plant photosynthesis. Hydrogen production performed by a single light reaction, as opposed to two, implies a doubling of the theoretically maximum thermodynamic conversion efficiency from {approx}10% to {approx}20%.

  17. Maximizing Light Utilization Efficiency and Hydrogen Production in Microalgal Cultures

    Energy Technology Data Exchange (ETDEWEB)

    Melis, Anastasios [Univ. of California, Berkeley, CA (United States)

    2014-12-31

    The project addressed the following technical barrier from the Biological Hydrogen Production section of the Fuel Cell Technologies Program Multi-Year Research, Development and Demonstration Plan: Low Sunlight Utilization Efficiency in Photobiological Hydrogen Production is due to a Large Photosystem Chlorophyll Antenna Size in Photosynthetic Microorganisms (Barrier AN: Light Utilization Efficiency).

  18. Principle and perspectives of hydrogen production through biocatalyzed electrolysis

    NARCIS (Netherlands)

    Rozendal, R.A.; Hamelers, H.V.M.; Euverink, G.J.W.; Metz, S.J.; Buisman, C.J.N.

    2006-01-01

    Biocatalyzed electrolysis is a novel biological hydrogen production process with the potential to efficiently convert a wide range of dissolved organic materials in wastewaters. Even substrates formerly regarded to be unsuitable for hydrogen production due to the endothermic nature of the involved c

  19. Principle and perspectives of hydrogen production through biocatalyzed electrolysis

    NARCIS (Netherlands)

    Rozendal, R.A.; Hamelers, H.V.M.; Euverink, G.J.W.; Metz, S.J.; Buisman, C.J.N.

    2006-01-01

    Biocatalyzed electrolysis is a novel biological hydrogen production process with the potential to efficiently convert a wide range of dissolved organic materials in wastewaters. Even substrates formerly regarded to be unsuitable for hydrogen production due to the endothermic nature of the involved

  20. Principle and perspectives of hydrogen production through biocatalyzed electrolysis

    NARCIS (Netherlands)

    Rozendal, René A.; Hamelers, Hubertus V.M.; Euverink, Gerrit J.W.; Metz, Sybrand J.; Buisman, Cees J.N.

    2006-01-01

    Biocatalyzed electrolysis is a novel biological hydrogen production process with the potential to efficiently convert a wide range of dissolved organic materials in wastewaters. Even substrates formerly regarded to be unsuitable for hydrogen production due to the endothermic nature of the involved c

  1. Solar and Wind Technologies for Hydrogen Production Report to Congress

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2005-12-01

    DOE's Solar and Wind Technologies for Hydrogen Production Report to Congress summarizes the technology roadmaps for solar- and wind-based hydrogen production. Published in December 2005, it fulfills the requirement under section 812 of the Energy Policy Act of 2005.

  2. Partial Characteristics of Hydrogen Production by Fermentative Hydrogen-producing Bacterial Strain B49

    Institute of Scientific and Technical Information of China (English)

    Wang Xiangjing(王相晶); Ren Nanqi; Xiang Wensheng; Lin Ming; Guo Wanqian

    2003-01-01

    To investigate the characteristics of hydrogen production by a novel fermentative hydrogen-producing bacterial strain B49 (AF481148 in EMBL), batch experiments are conducted under different conditions. Hydrogen production has a correlation with cell growth and the consumption of glucose and soluble protein. The optimum pH for cell growth is 4.5±0.15. At acidic pH 4.0±0.15, the bacteria has the maximum accumulated hydrogen volume of 2382 ml/L culture and the maximum hydrogen evolution rate of 339.9 ml/L culture*h with 1% glucose. The optimum temperature for cell growth and hydrogen production is 35℃. In addition, fermentative hydrogen-producing bacterial strain B49 can generate hydrogen from the decomposition of other organic substrates such as wheat, soybean, corn, and potato. Moreover, it can also produce hydrogen from molasses wastewater and brewage wastewater, and hydrogen yields are 137.9 ml H2/g COD and 49.9 ml H2/g COD, respectively.

  3. Steam reforming of natural gas with integrated hydrogen separation for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Oertel, M.; Schmitz, J.; Weirich, W.; Jendryssek-Neumann, D.; Schulten, R.

    1987-08-01

    The development of heat resistant permeation membranes has opened up new possibilities for the conversion of fossil energy resources. In steam reforming of natural gas, such membranes even permit a direct production of hydrogen at high temperatures during the conversion of feed hydrocarbons. Further gas processing, such as required for reformer gas in existing hydrogen production processes, is not necessary. Due to continuous hydrogen discharge directly in the reformer tube, the chemical equilibrium of the occurring reactions becomes displaced towards the products, resulting in more favourable process conditions and, consequently, in improved by 36% utilization of the feed hydrocarbons. At the same time, the hydrogen yield increases by 44%. The heat required, which is provided by a high temperature reactor, is 17% in excess of that in conventional plants. It can be expected that the simplified process design will produce substantial cost advantages over the existing processes for the production of hydrogen.

  4. Selecting effective hydrogen production and delivery options for mining applications

    Energy Technology Data Exchange (ETDEWEB)

    Curran, K.M. [Air Liquide Canada Inc., Ottawa, ON (Canada)

    2007-11-15

    This paper explored solutions to the challenges facing underground mining operations with respect to diesel powered equipment that results in increased ventilation requirements. The use of hydrogen as a fuel offers benefits in the area of reduced particulate and toxic emissions when it is used both in an internal combustion engine and when the energy of hydrogen is converted to electricity via a fuel cell. This paper examined the economics associated with 4 portions of the hydrogen supply chain for 3 commercially available methods for hydrogen supply. The 4 elements of each supply chain were production, distribution, storage and dispensing. The 3 methods for supply included gaseous product delivered by tube trailers; gaseous hydrogen onsite production through electrolysis; and, liquid hydrogen delivery. The choice of hydrogen supply mode was shown to be a complex process that must take into account all elements of the supply chain in terms of the end user defined by flow rate, pressure and purity. The cost of energy must also be considered, both for onsite production and for the transport cost of any delivered product. It was concluded that gaseous hydrogen offers flexibility in lower flow situations while liquid hydrogen offers the most economic supply method when distance from the liquid source is manageable by bulk tanker. 14 figs.

  5. Fermentative hydrogen production by microbial consortium

    Energy Technology Data Exchange (ETDEWEB)

    Maintinguer, Sandra I.; Fernandes, Bruna S.; Duarte, Iolanda C.S.; Saavedra, Nora Katia; Adorno, M. Angela T.; Varesche, M. Bernadete [Department of Hydraulics and Sanitation, School of Engineering of Sao Carlos, University of Sao Paulo, Av. Trabalhador Sao-carlense, 400, 13566-590 Sao Carlos-SP (Brazil)

    2008-08-15

    Heat pre-treatment of the inoculum associated to the pH control was applied to select hydrogen-producing bacteria and endospores-forming bacteria. The source of inoculum to the heat pre-treatment was from a UASB reactor used in the slaughterhouse waste treatment. The molecular biology analyses indicated that the microbial consortium presented microorganisms affiliated with Enterobacter cloacae (97% and 98%), Clostridium sp. (98%) and Clostridium acetobutyricum (96%), recognized as H{sub 2} and volatile acids' producers. The following assays were carried out in batch reactors in order to verify the efficiencies of sucrose conversion to H{sub 2} by the microbial consortium: (1) 630.0 mg sucrose/L, (2) 1184.0 mg sucrose/L, (3) 1816.0 mg sucrose/L and (4) 4128.0 mg sucrose/L. The subsequent yields were obtained as follows: 15% (1.2 mol H{sub 2}/mol sucrose), 20% (1.6 mol H{sub 2}/mol sucrose), 15% (1.2 mol H{sub 2}/mol sucrose) and 4% (0.3 mol H{sub 2}/mol sucrose), respectively. The intermediary products were acetic acid, butyric acid, methanol and ethanol in all of the anaerobic reactors. (author)

  6. Open-loop thermochemical cycles for the production of hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Conger, W.L.

    1979-01-01

    The concept of open-loop thermochemical cycles (cycles which have additional or other feedstocks than water and produce materials in addition to hydrogen and oxygen) is introduced. Preliminary analysis of possible feedstocks available indicates substantial quantities of hydrogen could possibly be produced through open-cycles. The advantages of open-cycles include the conversion of unwanted waste products to useful products while producing hydrogen. A compilation of open processes which would have SO/sub 2/ in addition to water as feedstock and which would produce sulfuric acid in addition to hydrogen and oxygen is given.

  7. Hydrogen Production Cost Estimate Using Biomass Gasification: Independent Review

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, M.

    2011-10-01

    This independent review is the conclusion arrived at from data collection, document reviews, interviews and deliberation from December 2010 through April 2011 and the technical potential of Hydrogen Production Cost Estimate Using Biomass Gasification. The Panel reviewed the current H2A case (Version 2.12, Case 01D) for hydrogen production via biomass gasification and identified four principal components of hydrogen levelized cost: CapEx; feedstock costs; project financing structure; efficiency/hydrogen yield. The panel reexamined the assumptions around these components and arrived at new estimates and approaches that better reflect the current technology and business environments.

  8. Hydrogen Production Cost Estimate Using Biomass Gasification: Independent Review

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2011-10-01

    This independent review is the conclusion arrived at from data collection, document reviews, interviews and deliberation from December 2010 through April 2011 and the technical potential of Hydrogen Production Cost Estimate Using Biomass Gasification. The Panel reviewed the current H2A case (Version 2.12, Case 01D) for hydrogen production via biomass gasification and identified four principal components of hydrogen levelized cost: CapEx; feedstock costs; project financing structure; efficiency/hydrogen yield. The panel reexamined the assumptions around these components and arrived at new estimates and approaches that better reflect the current technology and business environments.

  9. Electrolytic production of hydrogen utilizing photovoltaic cells

    Energy Technology Data Exchange (ETDEWEB)

    Daugherty, M.A.

    1996-10-01

    Hydrogen has the potential to serve as both an energy storage means and an energy carrier in renewable energy systems. When renewable energy sources such as solar or wind power are used to produce electrical power, the output can vary depending on weather conditions. By using renewable sources to produce hydrogen, a fuel which can be stored and transported, a reliable and continuously available energy supply with a predictable long-term average output is created. Electrolysis is one method of converting renewable energy into hydrogen fuel. In this experiment we examine the use of an electrolyzer based on polymer-electrolyte membrane technology to separate water into hydrogen and oxygen. The oxygen is vented to the atmosphere and the hydrogen is stored in a small pressure vessel.

  10. The endogenous production of hydrogen sulphide in intrauterine tissues

    Directory of Open Access Journals (Sweden)

    Wang Rui

    2009-02-01

    Full Text Available Abstract Background Hydrogen sulphide is a gas signalling molecule which is produced endogenously from L-cysteine via the enzymes cystathionine beta-synthase (CBS and cystathionine gamma-lyase (CSE. The possible role of hydrogen sulphide in reproduction has not yet been fully investigated. It has been previously demonstrated that hydrogen sulphide relaxes uterine smooth muscle in vitro. The aim of the present study was to investigate the endogenous production of hydrogen sulphide in rat and human intrauterine tissues in vitro. Methods The production of hydrogen sulphide in rat and human intrauterine tissues was measured in vitro using a standard technique. The expression of CBS and CSE was also investigated in rat and human intrauterine tissues via Western blotting. Furthermore, the effects of nitric oxide (NO and low oxygen conditions on the production rates of hydrogen sulphide were investigated. Results The order of hydrogen sulphide production rates (mean +/- SD, n = 4 for rat tissues were: liver (777 +/- 163 nM/min/g > uterus (168 +/- 100 nM/min/g > fetal membranes (22.3 +/- 15.0 nM/min/g > placenta (11.1 +/- 4.7 nM/min/g, compared to human placenta (200 +/- 102 nM/min/g. NO significantly increased hydrogen sulphide production in rat fetal membranes (P Conclusion Rat and human intrauterine tissues produce hydrogen sulphide in vitro possibly via CBS and CSE enzymes. NO increased the production of hydrogen sulphide in rat fetal membranes. The augmentation of hydrogen sulphide production in human intrauterine tissues in a low oxygen environment could have a role in pathophysiology of pregnancy.

  11. Hydrogen production by the decomposition of water

    Science.gov (United States)

    Hollabaugh, C.M.; Bowman, M.G.

    A process is described for the production of hydrogen from water by a sulfuric acid process employing electrolysis and thermo-chemical decomposition. The water containing SO/sub 2/ is electrolyzed to produce H/sub 2/ at the cathode and to oxidize the SO/sub 2/ to form H/sub 2/SO/sub 4/ at the anode. After the H/sub 2/ has been separated, a compound of the type M/sub r/X/sub s/ is added to produce a water insoluble sulfate of M and a water insoluble oxide of the metal in the radical X. In the compound M/sub r/X/sub s/, M is at least one metal selected from the group consisting of Ba/sup 2 +/, Ca/sup 2 +/, Sr/sup 2 +/, La/sup 2 +/, and Pb/sup 2 +/; X is at least one radical selected from the group consisting of molybdate (MoO/sub 4//sup 2 -/), tungstate (WO/sub 4//sup 2 -/), and metaborate (BO/sub 2//sup 1 -/); and r and s are either 1, 2, or 3 depending upon the valence of M and X. The precipitated mixture is filtered and heated to a temperature sufficiently high to form SO/sub 3/ gas and to reform M/sub r/X/sub s/. The SO/sub 3/ is dissolved in a small amount of H/sub 2/O to produce concentrated H/sub 2/SO/sub 4/, and the M/sub r/X/sub s/ is recycled to the process. Alternatively, the SO/sub 3/ gas can be recycled to the beginning of the process to provide a continuous process for the production of H/sub 2/ in which only water need be added in a substantial amount. (BLM)

  12. The Westerbork Hydrogen Accretion in Local Galaxies (HALOGAS) Survey I. Survey Description and Pilot Observations

    CERN Document Server

    Heald, George; Serra, Paolo; Zschaechner, Laura; Rand, Richard; Fraternali, Filippo; Oosterloo, Tom; Walterbos, Rene; Juette, Eva; Gentile, Gianfranco

    2010-01-01

    We introduce a new, very deep neutral hydrogen (HI) survey being performed with the Westerbork Synthesis Radio Telescope (WSRT). The Westerbork Hydrogen Accretion in LOcal GAlaxieS (HALOGAS) Survey is producing an archive of some of the most sensitive HI observations available, on the angular scales which are most useful for studying faint, diffuse gas in and around nearby galaxies. The survey data are being used to perform careful modeling of the galaxies, characterizing their gas content, morphology, and kinematics, with the primary goal of revealing the global characteristics of cold gas accretion onto spiral galaxies in the local Universe. In this paper, we describe the survey sample selection, the data acquisition, reduction, and analysis, and present the data products obtained during our pilot program, which consists of UGC 2082, NGC 672, NGC 925, and NGC 4565. The observations reveal a first glimpse of the picture that the full HALOGAS project aims to illuminate: the properties of accreting HI in diffe...

  13. Photoelectrochemical hydrogen production from biomass derivatives and water.

    Science.gov (United States)

    Lu, Xihong; Xie, Shilei; Yang, Hao; Tong, Yexiang; Ji, Hongbing

    2014-11-21

    Hydrogen, a clean energy carrier with high energy capacity, is a very promising candidate as a primary energy source for the future. Photoelectrochemical (PEC) hydrogen production from renewable biomass derivatives and water is one of the most promising approaches to producing green chemical fuel. Compared to water splitting, hydrogen production from renewable biomass derivatives and water through a PEC process is more efficient from the viewpoint of thermodynamics. Additionally, the carbon dioxide formed can be re-transformed into carbohydrates via photosynthesis in plants. In this review, we focus on the development of photoanodes and systems for PEC hydrogen production from water and renewable biomass derivatives, such as methanol, ethanol, glycerol and sugars. We also discuss the future challenges and opportunities for the design of the state-of-the-art photoanodes and PEC systems for hydrogen production from biomass derivatives and water.

  14. Fermentative hydrogen production from xylose using anaerobic mixed microflora

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Chiu-Yue; Cheng, Chao-Hui [BioHydrogen Laboratory, Department of Hydraulic Engineering, Feng Chia University, P.O. Box 25-123, Taichung 40724 (Taiwan)

    2006-06-15

    Sewage sludge microflora were anaerobically cultivated in a chemostat-type anaerobic bioreactor at a temperature of 35+/-1{sup o}C, pH of 7.1 and hydraulic retention time of 12h to determine the hydrogen production efficiency from xylose (20g-COD/L). This enriched microflora was used as a seed in batch experiments to investigate the pH and substrate concentration effects on hydrogen-producing bioactivity. It is demonstrated that the enriched mesophilic sewage sludge microflora with a continuous feeding can produce hydrogen from xylose with hydrogen content of 32% (v/v) in the biogas. Each mole of xylose yields 0.7moles of hydrogen and each gram of biomass produces 0.038moles of hydrogen per day. According to the batch test results, changes in pH and xylose concentration could enhance the microflora hydrogen production activity. Batch cultivation of this mixed microflora at pH values of 6-7 and xylose concentrations of 20g-COD/L resulted in high hydrogen production with a yield of 1.92-2.25mol-H{sub 2}/mol-xylose. This value is comparable to that from an enrichment culture. Strategies based on pH and xylose concentration controls for optimal hydrogen production from xylose using sewage sludge microflora are proposed. (author)

  15. Hydrogen production by fermentation using acetic acid and lactic acid.

    Science.gov (United States)

    Matsumoto, Mitsufumi; Nishimura, Yasuhiko

    2007-03-01

    Microbial hydrogen production from sho-chu post-distillation slurry solution (slurry solution) containing large amounts of organic acids was investigated. The highest hydrogen producer, Clostridium diolis JPCC H-3, was isolated from natural environment and produced hydrogen at 6.03+/-0.15 ml from 5 ml slurry solution in 30 h. Interestingly, the concentration of acetic acid and lactic acid in the slurry solution decreased during hydrogen production. The substrates for hydrogen production by C. diolis JPCC H-3, in particular organic acids, were investigated in an artificial medium. No hydrogen was produced from acetic acid, propionic acid, succinic acid, or citric acid on their own. Hydrogen and butyric acid were produced from a mixture of acetic acid and lactic acid, showing that C. diolis. JPCC H-3 could produce hydrogen from acetic acid and lactic acid. Furthermore, calculation of the Gibbs free energy strongly suggests that this reaction would proceed. In this paper, we describe for the first time microbial hydrogen production from acetic acid and lactic acid by fermentation.

  16. Hydrogen production by Rhodobacter sphaeroides DSM 158 under intense irradiation.

    Science.gov (United States)

    Krujatz, Felix; Härtel, Paul; Helbig, Karsten; Haufe, Nora; Thierfelder, Simone; Bley, Thomas; Weber, Jost

    2015-01-01

    To identify optimal hydrogen production conditions using growing cultures of Rhodobacter sphaeroides DSM 158 the effects of varying the reactor's volumetric power input (0.01-1.4kWm(-3)) and irradiation intensity (5-2500Wm(-2)) were investigated in batch and continuous production modes. Irradiation intensity had a greater effect on hydrogen production than volumetric power input. Hydrogen production and photofermentative biomass formation were maximized by irradiation at 2250Wm(-2) with a volumetric power input of 0.55kWm(-3). The bacterial dry weight (2.64gL(-1)) and rate of hydrogen production (195mLL(-1)h(-1)) achieved under these conditions were greater than any that have previously been reported for batch-mode hydrogen production by R. sphaeroides. Continuous mode experiments (D=0.1h(-1)) yielded a bacterial dry weight, hydrogen production rate, productivity and hydrogen yield of 2.35±0.18gL(-1), 165±6.2mLL(-1)h(-1), 3.96LL(-1)d(-1) and 36.6%, respectively.

  17. Comparative analysis of hydrogen-producing bacteria and its immobilized cells for characteristics of hydrogen production

    Institute of Scientific and Technical Information of China (English)

    王相晶; 任南琪; 向文胜; 王爱杰; 林明; 郭婉茜

    2003-01-01

    A strain of hydrogen producing bacteria was immobilized by polyvinyl alcohol-boric acid method,with the addition of a small amount of calcium alginate. The immobilized cells were insensitive to the presence of traces of O2. Moreover, the immobilized cells increased both the evolution rate and the yield of hydrogen production. Batch experiments with a medium containing 10 g/L glucose demonstrated the yields of hydrogen production by the immobilized and free cells were 2.14 mol/mol glucose and 1.69 mol/mol glucose, respectively.In continuous cultures atmedium retention time of 2. 0 h, the yield and the evolution rate of hydrogen producmedium retention time of 6. 0 h, the yield and the evolution rate of hydrogen production by free cells were only 1.75 mol/mol glucose and 362.9ml/(L·h),respectively.

  18. Microbiological Hydrogen Production by Anaerobic Fermentation and Photosynthetic Process

    Energy Technology Data Exchange (ETDEWEB)

    Asada, Y.; Ohsawa, M.; Nagai, Y.; Fukatsu, M.; Ishimi, K.; Ichi-ishi, S.

    2009-07-01

    Hydrogen gas is a clean and renewable energy carrier. Microbiological hydrogen production from glucose or starch by combination used of an anaerobic fermenter and a photosynthetic bacterium, Rhodobacter spheroides RV was studied. In 1984, the co-culture of Clostridium butyricum and RV strain to convert glucose to hydrogen was demonstrated by Miyake et al. Recently, we studied anaerobic fermentation of starch by a thermophilic archaea. (Author)

  19. Hydrogen production from dimethyl ether using corona discharge plasma

    Science.gov (United States)

    Zou, Ji-Jun; Zhang, Yue-Ping; Liu, Chang-Jun

    Dimethyl ether (DME), with its non-toxic character, high H/C ratio and high-energy volumetric density, is an ideal resource for hydrogen production. In this work, hydrogen production from the decomposition of DME using corona discharge has been studied. The corona discharge plasma decomposition was conducted at ambient conditions. The effects of dilution gas (argon), flow rate, frequency and waveforms on the DME decomposition were investigated. The addition of dilution gas can significantly increase the hydrogen production rate. The highest hydrogen production rate with the lowest energy consumption presents at the flow rate of 27.5 Nml min -1. AC voltage is more favored than DC voltage for the production of hydrogen with less energy input. The optimal frequency is 2.0 kHz. The hydrogen production rate is also affected by the input waveform and decreases as following: sinusoid triangular > sinusoid > ramp > square, whereas the sinusoid waveform shows the highest energy efficiency. The corona discharge decomposition of DME is leading to a simple, easy and convenient hydrogen production with no needs of catalyst and external heating.

  20. Production of bioplastics and hydrogen gas by photosynthetic microorganisms

    Science.gov (United States)

    Yasuo, Asada; Masato, Miyake; Jun, Miyake

    1998-03-01

    Our efforts have been aimed at the technological basis of photosynthetic-microbial production of materials and an energy carrier. We report here accumulation of poly-(3-hydroxybutyrate) (PHB), a raw material of biodegradable plastics and for production of hydrogen gas, and a renewable energy carrier by photosynthetic microorganisms (tentatively defined as cyanobacteria plus photosynthetic bateria, in this report). A thermophilic cyanobacterium, Synechococcus sp. MA19 that accumulates PHB at more than 20% of cell dry wt under nitrogen-starved conditions was isolated and microbiologically identified. The mechanism of PHB accumulation was studied. A mesophilic Synechococcus PCC7942 was transformed with the genes encoding PHB-synthesizing enzymes from Alcaligenes eutrophus. The transformant accumulated PHB under nitrogen-starved conditions. The optimal conditions for PHB accumulation by a photosynthetic bacterium grown on acetate were studied. Hydrogen production by photosynthetic microorganisms was studied. Cyanobacteria can produce hydrogen gas by nitrogenase or hydrogenase. Hydrogen production mediated by native hydrogenase in cyanobacteria was revealed to be in the dark anaerobic degradation of intracellular glycogen. A new system for light-dependent hydrogen production was targeted. In vitro and in vivo coupling of cyanobacterial ferredoxin with a heterologous hydrogenase was shown to produce hydrogen under light conditions. A trial for genetic trasformation of Synechococcus PCC7942 with the hydrogenase gene from Clostridium pasteurianum is going on. The strong hydrogen producers among photosynthetic bacteria were isolated and characterized. Co-culture of Rhodobacter and Clostriumdium was applied to produce hydrogen from glucose. Conversely in the case of cyanobacteria, genetic regulation of photosynthetic proteins was intended to improve conversion efficiency in hydrogen production by the photosynthetic bacterium, Rhodobacter sphaeroides RV. A mutant acquired by

  1. Potential application of anaerobic extremophiles for hydrogen production

    Science.gov (United States)

    Pikuta, Elena V.; Hoover, Richard B.

    2004-11-01

    In processes of the substrate fermentation most anaerobes produce molecular hydrogen as a waste end product, which often controls the culture growth as an inhibitor. Usually in nature the hydrogen is easily removed from an ecosystem, due to its physical features, and an immediate consumption by the secondary anaerobes that sometimes behave as competitors for electron donors; a classical example of this kind of substrate competition in anaerobic microbial communities is the interaction between methanogens and sulfate- or sulfur-reducers. Previously, on the mixed cultures of anaerobes at neutral pH, it was demonstrated that bacterial hydrogen production could provide a good alternative energy source. At neutral pH the original cultures could easily contaminated by methanogens, and the most unpleasant side effect of these conditions is the development of pathogenic bacteria. In both cases the rate of hydrogen production was dramatically decreased since some part of the hydrogen was transformed to methane, and furthermore, the cultivation with pathogenic contaminants on an industrial scale would create an unsafe situation. In our laboratory the experiments with obligately alkaliphilic bacteria producing hydrogen as an end metabolic product were performed at different conditions. The mesophilic, haloalkaliphilic and obligately anaerobic bacterium Spirochaeta americana ASpG1T was studied and various cultivation regimes were compared for the most effective hydrogen production. In a highly mineralized media with pH 9.5-10.0 not many known methanogens are capable of growth, and the probability of developing pathogenic contaminants is theoretically is close to zero (in medicine carbonate- saturated solutions are applied as antiseptics). Therefore the cultivation of alkaliphilic hydrogen producing bacteria could be considered as a safe and economical process for large-scale industrial bio-hydrogen production in the future. Here we present and discuss the experimental data

  2. Radiolytic Hydrogen Production in the South Pacific Subseafloor Basaltic Aquifer

    Science.gov (United States)

    Dzaugis, M. E.; Spivack, A. J.; Dunlea, A. G.; Murray, R. W.; D'Hondt, S.

    2015-12-01

    Hydrogen (H2) is produced in geological settings by dissociation of water due to radiation from natural radioactive decay of uranium (238U, 235U), thorium (232Th) and potassium (40K). To quantify the potential significance of radiolytic H2 as an electron donor for microbes within the South Pacific subseafloor basaltic aquifer, we calculate radiolytic H2 production rates in basement fractures utilizing measured radionuclide concentrations in 42 basalt samples from IODP Expedition 329. The samples are from three sites with very different basement ages and a wide range of alteration types. Major and trace element concentrations vary by up to an order of magnitude from sample to sample. Comparison of our samples to each other and to previous studies of fresh East Pacific Rise basalt suggests that between-sample variation in radionuclide concentrations is primarily due to differences in initial (pre-alteration) concentrations (which can vary between eruptive events), rather than to alteration type or extent. Local maxima in radionuclide (U, Th, and K) concentrations produce 'hotspots' of radiolytic H2 production; calculated radiolytic rates differ by up to a factor of 80 from sample to sample. Fracture width also greatly influences H2 production. Due to the low penetration distance of alpha radiation, microfractures are 'hotpots' for radiolytic H2 production. For example, radiolytic H2 production rates normalized to water volume are 170 times higher in 1μm-wide fractures than in 10cm-wide fractures.

  3. Hydrogen production from glucose by anaerobes.

    Science.gov (United States)

    Ogino, Hiroyasu; Miura, Takashi; Ishimi, Kosaku; Seki, Minoru; Yoshida, Hiroyuki

    2005-01-01

    Various anaerobes were cultivated in media containing glucose. When 100 mL of thioglycollate medium containing 2.0% (w/v) glucose was used, Clostridium butyricum ATCC 859, NBRC 3315, and NBRC 13949 evolved 227-243 mL of biogas containing about 180 mL of hydrogen in 1 day. Although some strains had some resistance against oxygen, C. butyricum ATCC 859 and 860 did not have it. C. butyricum NBRC 3315 and Enterobacter aerogenes NBRC 13534 produced hydrogen in the presence of glucose or pyruvic acid, and E. aerogenes NBRC 13534 produced hydrogen by not only glucose and pyruvic acid but also dextrin, sucrose, maltose, galactose, fructose, mannose, and mannitol. When a medium containing 0.5% (w/v) yeast extract and 2.0% (w/v) glucose was used, E. aerogenes NBRC 13534 evolved more biogas and hydrogen than C. butyricum NBRC 3315 in the absence of reducing agent.

  4. Hydrogen, lithium, and lithium hydride production

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Sam W.; Spencer, Larry S.; Phillips, Michael R.; Powell, G. Louis; Campbell, Peggy J.

    2017-06-20

    A method is provided for extracting hydrogen from lithium hydride. The method includes (a) heating lithium hydride to form liquid-phase lithium hydride; (b) extracting hydrogen from the liquid-phase lithium hydride, leaving residual liquid-phase lithium metal; (c) hydriding the residual liquid-phase lithium metal to form refined lithium hydride; and repeating steps (a) and (b) on the refined lithium hydride.

  5. Hydrogen production from biodiesel byproduct by immobilized Enterobacter aerogenes.

    Science.gov (United States)

    Han, Jinmi; Lee, Dohoon; Cho, Jinku; Lee, Jeewon; Kim, Sangyong

    2012-01-01

    The recent rapid growth of the biodiesel industry has generated a significant amount of glycerol as a byproduct. As a result, the price of glycerol is currently relatively low, making it an attractive starting material for the production of chemicals with higher values. Crude glycerol can be directly converted through microbial fermentation into various chemicals such as hydrogen. In this study, we optimized immobilization of a facultative hydrogen producing microorganism, Enterobacter aerogenes, with the goal of developing biocatalysts that was appropriate for the continuous hydrogen production from glycerol. Several carriers were tested and agar was found to be the most effective. In addition, it was clearly shown that variables such as the carrier content and cell loading should be controlled for the immobilization of biocatalysts with high hydrogen productivity, stability, and reusability. After optimization of these variables, we were able to obtain reusable biocatalysts that could directly convert the byproduct stream from biodiesel processes into hydrogen in continuous processes.

  6. Nano cobalt oxides for photocatalytic hydrogen production

    KAUST Repository

    Mangrulkar, Priti A.

    2012-07-01

    Nano structured metal oxides including TiO 2, Co 3O 4 and Fe 3O 4 have been synthesized and evaluated for their photocatalytic activity for hydrogen generation. The photocatalytic activity of nano cobalt oxide was then compared with two other nano structured metal oxides namely TiO 2 and Fe 3O 4. The synthesized nano cobalt oxide was characterized thoroughly with respect to EDX and TEM. The yield of hydrogen was observed to be 900, 2000 and 8275 mmol h -1 g -1 of photocatalyst for TiO 2, Co 3O 4 and Fe 3O 4 respectively under visible light. It was observed that the hydrogen yield in case of nano cobalt oxide was more than twice to that of TiO 2 and the hydrogen yield of nano Fe 3O 4 was nearly four times as compared to nano Co 3O 4. The influence of various operating parameters in hydrogen generation by nano cobalt oxide was then studied in detail. Copyright © 2012, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

  7. Electrolytic production and dispensing of hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, C.E.; Kuhn, I.F. Jr. [Directed Technologies, Inc., Arlington, VA (United States)

    1995-09-01

    The fuel cell electric vehicle (FCEV) is undoubtedly the only option that can meet both the California zero emission vehicle (ZEV) standard and the President`s goal of tripling automobile efficiency without sacrificing performance in a standard 5-passenger vehicle. The three major automobile companies are designing and developing FCEVs powered directly by hydrogen under cost-shared contracts with the Department of Energy. Once developed, these vehicles will need a reliable and inexpensive source of hydrogen. Steam reforming of natural gas would produce the least expensive hydrogen, but funding may not be sufficient initially to build both large steam reforming plants and the transportation infrastructure necessary to deliver that hydrogen to geographically scattered FCEV fleets or individual drivers. This analysis evaluates the economic feasibility of using small scale water electrolysis to provide widely dispersed but cost-effective hydrogen for early FCEV demonstrations. We estimate the cost of manufacturing a complete electrolysis system in large quantities, including compression and storage, and show that electrolytic hydrogen could be cost competitive with fully taxed gasoline, using existing residential off-peak electricity rates.

  8. Hydrogen production via thermal gasification of biomass in near-to-medium term

    Energy Technology Data Exchange (ETDEWEB)

    Hannula, I.

    2009-09-15

    Dedicated biomass gasification technologies are presently being developed in many countries for the production of second-generation liquid biofuels. Both fluidised-bed gasification and special entrained flow systems are under intensive development. These technologies can also be used for hydrogen production, which may become an interesting alternative in replacing part of fossil fuel input in oil refineries and chemical industries. In addition, fuel cell technology is being developed for hydrogen-rich gases. New and revolutionary production methods, capable of replacing the classical process routes, can not however be foreseen to emerge in the medium-term. Also the new hydrogen separation technologies, presently under development, seem to have only limited potential to reduce the production cost of hydrogen compared to commercially available technology. However, with rising prices of fossil fuels and locally depleting natural gas reserves, gasification route is likely to gain more ground as a credible production technology for hydrogen. The global needs to cut down the CO{sub 2} emissions can also make gasification of biomass an interesting possibility. Several biomass gasification processes are presently at demonstration phase, mostly aimed for the production of liquid transportation fuels. If and when this technology will be commercialized, it could easily be adopted to the production of hydrogen. (orig.)

  9. Study of hydrogen production from wind power in Algeria

    Energy Technology Data Exchange (ETDEWEB)

    Aiche-Hamane, Lilia; Belhamel, Maiouf; Benyoucef, Boumedienne; Hamane, Mustapha [Centre for Development of Renewable Energies (CDER), Alger (Algeria)

    2010-07-01

    An overview of the potentiality of hydrogen production from wind power in Algeria has been given in this study. Wind resource assessment has been presented in cartographic form and windy sites have been identified for wind power application. A system constituted by a wind turbine, an electrolyser and a power conditioning device have been proposed for the study of hydrogen production in the southwest region of Algeria. For this purpose, the transient system simulation program (TRNSYS) have been used. The results obtained showed the sensitivity of hydrogen production to the wind resource trend and the importance of optimisation of the electrolyser according to the power produced by the wind turbine. (orig.)

  10. Estimation of bacterial hydrogen sulfide production in vitro

    Directory of Open Access Journals (Sweden)

    Amina Basic

    2015-06-01

    Full Text Available Oral bacterial hydrogen sulfide (H2S production was estimated comparing two different colorimetric methods in microtiter plate format. High H2S production was seen for Fusobacterium spp., Treponema denticola, and Prevotella tannerae, associated with periodontal disease. The production differed between the methods indicating that H2S production may follow different pathways.

  11. Hydrogen production with a solar steam–methanol reformer and colloid nanocatalyst

    KAUST Repository

    Lee, Ming-Tsang

    2010-01-01

    In the present study a small steam-methanol reformer with a colloid nanocatalyst is utilized to produce hydrogen. Radiation from a focused continuous green light laser (514 nm wavelength) is used to provide the energy for steam-methanol reforming. Nanocatalyst particles, fabricated by using pulsed laser ablation technology, result in a highly active catalyst with high surface to volume ratio. A small novel reformer fabricated with a borosilicate capillary is employed to increase the local temperature of the reformer and thereby increase hydrogen production. The hydrogen production output efficiency is determined and a value of 5% is achieved. Experiments using concentrated solar simulator light as the radiation source are also carried out. The results show that hydrogen production by solar steam-methanol colloid nanocatalyst reforming is both feasible and promising. © 2009 Professor T. Nejat Veziroglu.

  12. Improvements in Fermentative Biological Hydrogen Production Through Metabolic Engineering

    Energy Technology Data Exchange (ETDEWEB)

    Hallenbeck, P. C.; Ghosh, D.; Sabourin-Provost, G.

    2009-07-01

    Dramatically rising oil prices and increasing awareness of the dire environmental consequences of fossil fuel use, including startling effects of climate change, are refocusing attention world-wide on the search for alternative fuels. Hydrogen is poised to become an important future energy carrier. Renewable hydrogen production is pivotal in making it a truly sustainable replacement for fossil fuels. (Author)

  13. Technical suitability mapping of feedstocks for biological hydrogen production

    NARCIS (Netherlands)

    Panagiotopoulos, I.A.; Karaoglanoglou, L.S.; Koullas, D.P.; Bakker, R.R.; Claassen, P.A.M.; Koukios, E.G.

    2015-01-01

    The objective of this work was to map and compare the technical suitability of different raw materials for biological hydrogen production. Our model was based on hydrogen yield potential, sugar mobilization efficiency, fermentability and coproduct yield and value. The suitability of the studied r

  14. On-Board Hydrogen Gas Production System For Stirling Engines

    Science.gov (United States)

    Johansson, Lennart N.

    2004-06-29

    A hydrogen production system for use in connection with Stirling engines. The production system generates hydrogen working gas and periodically supplies it to the Stirling engine as its working fluid in instances where loss of such working fluid occurs through usage through operation of the associated Stirling engine. The hydrogen gas may be generated by various techniques including electrolysis and stored by various means including the use of a metal hydride absorbing material. By controlling the temperature of the absorbing material, the stored hydrogen gas may be provided to the Stirling engine as needed. A hydrogen production system for use in connection with Stirling engines. The production system generates hydrogen working gas and periodically supplies it to the Stirling engine as its working fluid in instances where loss of such working fluid occurs through usage through operation of the associated Stirling engine. The hydrogen gas may be generated by various techniques including electrolysis and stored by various means including the use of a metal hydride absorbing material. By controlling the temperature of the absorbing material, the stored hydrogen gas may be provided to the Stirling engine as needed.

  15. Hydrogen production econometric studies. [hydrogen and fossil fuels

    Science.gov (United States)

    Howell, J. R.; Bannerot, R. B.

    1975-01-01

    The current assessments of fossil fuel resources in the United States were examined, and predictions of the maximum and minimum lifetimes of recoverable resources according to these assessments are presented. In addition, current rates of production in quads/year for the fossil fuels were determined from the literature. Where possible, costs of energy, location of reserves, and remaining time before these reserves are exhausted are given. Limitations that appear to hinder complete development of each energy source are outlined.

  16. Renewable hydrogen production for fossil fuel processing

    Energy Technology Data Exchange (ETDEWEB)

    Greenbaum, E.; Lee, J.W.; Tevault, C.V. [and others

    1995-06-01

    In the fundamental biological process of photosynthesis, atmospheric carbon dioxide is reduced to carbohydrate using water as the source of electrons with simultaneous evolution of molecular oxygen: H{sub 2}O + CO{sub 2} + light {yields} O{sub 2} + (CH{sub 2}O). It is well established that two light reactions, Photosystems I and II (PSI and PSII) working in series, are required to perform oxygenic photosynthesis. Experimental data supporting the two-light reaction model are based on the quantum requirement for complete photosynthesis, spectroscopy, and direct biochemical analysis. Some algae also have the capability to evolve molecular hydrogen in a reaction energized by the light reactions of photosynthesis. This process, now known as biophotolysis, can use water as the electron donor and lead to simultaneous evolution of molecular hydrogen and oxygen. In green algae, hydrogen evolution requires prior incubation under anaerobic conditions. Atmospheric oxygen inhibits hydrogen evolution and also represses the synthesis of hydrogenase enzyme. CO{sub 2} fixation competes with proton reduction for electrons relased from the photosystems. Interest in biophotolysis arises from both the questions that it raises concerning photosynthesis and its potential practical application as a process for converting solar energy to a non-carbon-based fuel. Prior data supported the requirement for both Photosystem I and Photosystem II in spanning the energy gap necessary for biophotolysis of water to oxygen and hydrogen. In this paper we report the at PSII alone is capable of driving sustained simultaneous photoevolution of molecular hydrogen and oxygen in an anaerobically adapted PSI-deficient strain of Chlamydomonas reinhardtii, mutant B4, and that CO{sub 2} competes as an electron acceptor.

  17. IEA Energy Technology Essentials: Hydrogen Production and Distribution

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-04-15

    The IEA Energy Technology Essentials series offers concise four-page updates on the different technologies for producing, transporting and using energy. Hydrogen Production and Distribution are the topics covered in this edition.

  18. Biological hydrogen production by moderately thermophilic anaerobic bacteria

    Energy Technology Data Exchange (ETDEWEB)

    HP Goorissen; AJM Stams [Laboratory of Microbiology, Wageningen University and Research centre Wageningen (Netherlands)

    2006-07-01

    This study focuses on the biological production of hydrogen at moderate temperatures (65-75 C) by anaerobic bacteria. A survey was made to select the best (moderate) thermophiles for hydrogen production from cellulolytic biomass. From this survey we selected Caldicellulosiruptor saccharolyticus (a gram-positive bacterium) and Thermotoga elfii (a gram-negative bacterium) as potential candidates for biological hydrogen production on mixtures of C{sub 5}-C{sub 6} sugars. Xylose and glucose were used as model substrates to describe growth and hydrogen production from hydrolyzed biomass. Mixed substrate utilization in batch cultures revealed differences in the sequence of substrate consumption and in catabolites repression of the two microorganisms. The regulatory mechanisms of catabolites repression in these microorganisms are not known yet. (authors)

  19. Hydrogen production by Clostridium thermolacticum during continuous fermentation of lactose

    Energy Technology Data Exchange (ETDEWEB)

    Collet, C.; Adler, N.; Schwitzguebel, J.P.; Peringer, P. [Swiss Federal Inst. of Technology Lausanne (EPFL) (Switzerland). Lab. for Environmental Biotechnology

    2004-11-01

    In the production of acetate by Clostridium thermolacticum growing on lactose, considerable amounts of hydrogen were generated. Lactose available in large amounts from milk permeate, a waste stream of the dairy industry, appears to be a valuable substrate for cheap production of biohydrogen. In this study, continuous cultivation of C. thermolacticum was carried out in a bioreactor, under anaerobic thermophilic conditions, on minimal medium containing 10 g l{sup -1} lactose. Different dilution rates and pH were tested. C. thermolacticum growing on lactose produced acetate, ethanol and lactate in the liquid phase. For all conditions tested, hydrogen was the main product in the gas phase. Hydrogen specific production higher than 5 mmol H{sub 2} (g cell){sup -1} h{sup -1} was obtained. By operating this fermentation at high-dilution rate and alkaline pH, the hydrogen content in the gas phase was maximized. (author)

  20. Exergetic life cycle assessment of hydrogen production from renewables

    Science.gov (United States)

    Granovskii, Mikhail; Dincer, Ibrahim; Rosen, Marc A.

    Life cycle assessment is extended to exergetic life cycle assessment and used to evaluate the exergy efficiency, economic effectiveness and environmental impact of producing hydrogen using wind and solar energy in place of fossil fuels. The product hydrogen is considered a fuel for fuel cell vehicles and a substitute for gasoline. Fossil fuel technologies for producing hydrogen from natural gas and gasoline from crude oil are contrasted with options using renewable energy. Exergy efficiencies and greenhouse gas and air pollution emissions are evaluated for all process steps, including crude oil and natural gas pipeline transportation, crude oil distillation and natural gas reforming, wind and solar electricity generation, hydrogen production through water electrolysis, and gasoline and hydrogen distribution and utilization. The use of wind power to produce hydrogen via electrolysis, and its application in a fuel cell vehicle, exhibits the lowest fossil and mineral resource consumption rate. However, the economic attractiveness, as measured by a "capital investment effectiveness factor," of renewable technologies depends significantly on the ratio of costs for hydrogen and natural gas. At the present cost ratio of about 2 (per unit of lower heating value or exergy), capital investments are about five times lower to produce hydrogen via natural gas rather than wind energy. As a consequence, the cost of wind- and solar-based electricity and hydrogen is substantially higher than that of natural gas. The implementation of a hydrogen fuel cell instead of an internal combustion engine permits, theoretically, an increase in a vehicle's engine efficiency of about of two times. Depending on the ratio in engine efficiencies, the substitution of gasoline with "renewable" hydrogen leads to (a) greenhouse gas (GHG) emissions reductions of 12-23 times for hydrogen from wind and 5-8 times for hydrogen from solar energy, and (b) air pollution (AP) emissions reductions of 38

  1. Membrane reactor technology for ultrapure hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Patil, C.S.

    2005-11-17

    The main objectives of this thesis are (1) to compare different reactor types and assess the feasibility of operation; (2) to develop and design a novel reactor concept based on the integration of perm-selective hydrogen and oxygen membranes; and (3) to give an experimental proof of principle of the developed reactor concept. In Chapter 2, available perm-selective hydrogen and oxygen membranes are reviewed. The focus is on the reactor concepts using these membranes and commercial developments that have taken place. In Chapter 3, the feasibility of performing autothermal membrane reforming in a packed bed membrane reactor with perm-selective hydrogen membrane is investigated based on detailed two-dimensional non-isothermal reactor modelling. In Chapter 4, an alternative reactor concept is developed for the autothermal reforming of methane integrating both hydrogen and oxygen perm-selective membranes. In Chapter 5, experimental work on the perm-selective hydrogen membranes that are used in the top section of the proposed reactor concept has been elaborated. These membranes, procured from a commercial supplier, are tested for their perm-selectivity and the permeability of hydrogen at different temperature and hydrogen partial pressures. Using the flux data a lumped flux expression is developed which is subsequently used in the pilot scale reactor design (Chapter 7). In Chapter 6, the kinetic rate measurements for SRM on a highly active Shell CPO catalyst are described. A kinetic rate expression for the steam reforming/ water gas shift top section of the proposed novel reactor concept is developed. The bottom section of this reactor is essentially at thermodynamic equilibrium because of highly active CPO catalyst and high temperatures and hence a detailed kinetic investigation for this section is not undertaken. In Chapter 7, a single membrane prototype of the top section is tested experimentally followed by a scale-up and design to a pilot scale unit with 10 Pd

  2. Biophotolysis, hydrogen, production and algal culture technology

    Energy Technology Data Exchange (ETDEWEB)

    Skulberg, O.M. [Norwegian Inst. for Water Research, Oslo (Norway)

    1995-12-31

    In this essay the importance and place of biophotolysis in the hydrogen energy system is described. The biophotolysis of water is achieved by two biochemical processes carried out by the activity of chlorophyll containing reaction centres coupled to hydrogenase and nitrogenase. Micro algae belonging to the classes Chlorophyceae and Cyanophyceae can produce molecular hydrogen by the decomposition of water using solar energy. Among Anoxyphotobactelia organisms of the families Chrorna iaceae and Chlorobiaceae are also used for the bioengineering development of biophotolysis. A review is presented of the organisms and the processes involved in the context of their applications for algal culture technology. 2 tabs., 52 refs.

  3. NGNP Process Heat Applications: Hydrogen Production Accomplishments for FY2010

    Energy Technology Data Exchange (ETDEWEB)

    Charles V Park

    2011-01-01

    This report summarizes FY10 accomplishments of the Next Generation Nuclear Plant (NGNP) Engineering Process Heat Applications group in support of hydrogen production technology development. This organization is responsible for systems needed to transfer high temperature heat from a high temperature gas-cooled reactor (HTGR) reactor (being developed by the INL NGNP Project) to electric power generation and to potential industrial applications including the production of hydrogen.

  4. Renewable Production of Water, Hydrogen, and Power From Ambient Moisture

    Science.gov (United States)

    2016-12-01

    PRODUCTION OF WATER , HYDROGEN, AND POWER FROM AMBIENT MOISTURE by Angel Aviles December 2016 Thesis Advisor: Garth V. Hobson Co-Advisor...AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE RENEWABLE PRODUCTION OF WATER , HYDROGEN, AND POWER FROM AMBIENT MOISTURE 5. FUNDING...12b. DISTRIBUTION CODE 13. ABSTRACT (maximum 200 words ) This thesis developed a concept design and prototype system capable of increasing and

  5. In vitro hydrogen production by glucose dehydrogenase and hydrogenase

    Energy Technology Data Exchange (ETDEWEB)

    Woodward, J.; Mattingly, S.M. [Oak Ridge National Lab., TN (United States); Danson, M. [Univ. of Bath (United Kingdom)] [and others

    1996-07-01

    A new in vitro enzymatic pathway for the generation of molecular hydrogen from glucose has been demonstrated. The reaction is based on the oxidation of glucose by Thermoplasma acidophilum glucose dehydrogenase with the concomitant oxidation of NADPH by Pyrococcus furiosus hydrogenase. Stoichiometric yields of hydrogen were produced from glucose with the continuous recycling of cofactor. This simple system may provide a method for the biological production of hydrogen from renewable sources. In addition, the other product of this reaction, gluconic acid, is a high-value chemical commodity. 23 refs., 5 figs.

  6. In vitro hydrogen production by glucose dehydrogenase and hydrogenase

    Energy Technology Data Exchange (ETDEWEB)

    Woodward, J. [Oak Ridge National Lab., TN (United States)

    1996-10-01

    A new in vitro enzymatic pathway for the generation of molecular hydrogen from glucose has been demonstrated. The reaction is based upon the oxidation of glucose by Thermoplasma acidophilum glucose dehydrogenase with the concomitant oxidation of NADPH by Pyrococcus furiosus hydrogenase. Stoichiometric yields of hydrogen were produced from glucose with continuous cofactor recycle. This simple system may provide a method for the biological production of hydrogen from renewable sources. In addition, the other product of this reaction, gluconic acid, is a high-value commodity chemical.

  7. Photocatalytic Hydrogen Production by Direct Sunlight: A Laboratory Experiment

    Science.gov (United States)

    Koca, Atif; Sahin, Musa

    2003-11-01

    The demand for hydrogen will increase within the next decades as a result of the necessity to produce clean and environmentally and economically accepted fuels from natural and renewable energy resources. In principle, hydrogen has the potential to play an important role in future energy systems because of the diversity of its applications, the variety of ways in which it can be stored, its general environmental advantages, and especially because of the possibility of producing hydrogen by splitting water using photocatalysts and solar energy. Methods and techniques of photocatalytic reactions are covered in some detail in many undergraduate chemistry programs. However, many times in instructional settings, little attention is given to how it is used for the production of hydrogen. In the present investigation a photocatalytic hydrogen production experiment suitable for use in undergraduate chemistry laboratories is described. The experiment can be used to introduce students to the concept of a renewable and sustainable hydrogen energy system of the future, as well as its production techniques, and to demonstrate the use of a CdS/ZnS photocatalyst system for photocatalytic hydrogen production from direct sunlight.

  8. Hydrogenation of carbon dioxide for methanol production

    NARCIS (Netherlands)

    Ham, van der A.G.J.; Berg, van den H.; Benneker, A.; Simmelink, G.; Timmer, J.; Weerden, van S.

    2012-01-01

    A process for the hydrogenation of CO2 to methanol with a capacity of 10 kt/y methanol is designed in a systematic way. The challenge will be to obtain a process with a high net CO2 conversion. From initially four conceptual designs the most feasible is selected and designed in more detail. The feed

  9. Enrichment and hydrogen production by marine anaerobic hydrogen-producing microflora

    Institute of Scientific and Technical Information of China (English)

    CAI JinLing; WANG GuangCe; LI YanChuan; ZHU DaLing; PAN GuangHua

    2009-01-01

    Acid,alkali,heat-shock,KNO3 and control pretreatment methods applied to anaerobic sludge were evaluated for their ability to selectively enrich the marine hydrogen-producing mixed microflora.Seawater culture medium was used as the substrate.The hydrogen yield of pretreated microflora was higher than that of the un-pretreated control (P<0.05).Among the pretreatment methods studied,heat-shock pretreatment yielded the greatest hydrogen production,which was 14.6 times that of the control.When the effect of initial pH on hydrogen production of heat-shock pretreated samples was studied,hydrogen was produced over the entire pH range (pH 4-10).The hydrogen yield peaked at initial pH 8 (79 mL/g sucrose) and then steadily decreased as the initial pH increased.Sucrose consumption was high at neutral initial pH.During the process of hydrogen production,pH decreased gradually,which indicated that the acquired microflora consisted of acidogenic bacteria.

  10. Clean Hydrogen Production. Carbon Dioxide Free Alternatives. Project Phisico2

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Fierro, J. L.; Gonzalez, C.; Serrano, D.; Penelas, G.; Romero, M.; Marcos, M. J.; Rodriguez, C.

    2006-07-01

    The main goal of the PHISICO2 project, funded and promoted by Comunidad de Madrid, is the evaluation and optimisation of three different processes for the clean hydrogen production without carbon dioxide emission. Solar energy and associated Technologies are proposed to be jointly employed with the aim of improving the process efficiency and reducing the production costs. As a transition to the non-fossil fuel hydrogen economy, the thermocatalytic CO2-free production of hydrogen from natural gas will be considered. One of the most promising alternatives of this process is to develop a cheap and stable carbon-based catalyst able to efficiently decompose methane into a CO2-free hydrogen stream and solid carbon. Thus, not only pure hydrogen can be obtained through but also carbon with specific properties and commercial value can be produced. Another option to be explored is the splitting of water by means of solar light by means of two different approaches: (i) photodissociation promoted by semiconductor catalysts and (ii) thermochemical cycles in which a specific mixed oxide is first thermally reduced by sunlight and then reoxidized by steam in a second step with the parallel production of hydrogen. Indeed, option (i) implies necessarily the development of semiconductors with appropriate band-gap able to decompose water into hydrogen and oxygen in an efficient manner. Another critical issue will be the development of a strategy/concept that allows efficient separation of hydrogen and oxygen within the cell. In option (ii), the development of stable ferrites which act as the redox element of the cycle is also an important challenge. Finally, a 5 kW prototype solar engine water splitting, based on the mentioned thermochemical cycle, will developed and tested using concentrated solar light as an energy source. Moreover, thermodynamic and kinetic studies, reactor design, process optimisation, economical studies and comparison with conventional hydrogen production systems

  11. Production of hydrogen by thermocatalytic cracking of natural gas

    Energy Technology Data Exchange (ETDEWEB)

    Muradov, N.Z. [Univ. of Central Florida, Cape Canaveral, FL (United States)

    1995-09-01

    It is universally accepted that in the next few decades hydrogen production will continue to rely on fossil fuels (primarily, natural gas). On the other hand, the conventional methods of hydrogen production from natural gas (for example, steam reforming) are complex multi-step processes. These processes also result in the emission of large quantities of CO{sub 2} into the atmosphere that produce adverse ecological effects. One alternative is the one-step thermocatalytic cracking (TCC) (or decomposition) of natural gas into hydrogen and carbon. Preliminary analysis indicates that the cost of hydrogen produced by thermal decomposition of natural gas is somewhat lower than the conventional processes after by-product carbon credit is taken. In the short term, this process can be used for on-site production of hydrogen-methane mixtures in gas-filling stations and for CO{sub x}-free production of hydrogen for fuel cell driven prime movers. The experimental data on the thermocatalytic cracking of methane over various catalysts and supports in a wide range of temperatures (500-900{degrees}C) are presented in this paper. Two types of reactors were designed and built at FSEC: continuous flow and pulse fix bed catalytic reactors. The temperature dependence of the hydrogen production yield using oxide type catalysts was studied. Alumina-supported Ni- and Fe-catalysts demonstrated relatively high efficiency in the methane cracking reaction at moderate temperatures (600-800{degrees}C). Kinetic curves of hydrogen production over metal and metal oxide catalysts at different temperatures are presented in the paper. Fe-catalyst demonstrated good stability (for several hours), whereas alumina-supported Pt-catalyst rapidly lost its catalytic activity.

  12. Biological hydrogen production measured in batch anaerobic respirometers.

    Science.gov (United States)

    Logan, Bruce E; Oh, Sang-Eun; Kim, In S; Van Ginkel, Steven

    2002-06-01

    The biological production of hydrogen from the fermentation of different substrates was examined in batch tests using heat-shocked mixed cultures with two techniques: an intermittent pressure release method (Owen method) and a continuous gas release method using a bubble measurement device (respirometric method). Under otherwise identical conditions, the respirometric method resulted in the production of 43% more hydrogen gas from glucose than the Owen method. The lower conversion of glucose to hydrogen using the Owen protocol may have been produced by repression of hydrogenase activity from high partial pressures in the gastight bottles, but this could not be proven using a thermodynamic/rate inhibition analysis. In the respirometric method, total pressure in the headspace never exceeded ambient pressure, and hydrogen typically composed as much as 62% of the headspace gas. High conversion efficiencies were consistently obtained with heat-shocked soils taken at different times and those stored for up to a month. Hydrogen gas composition was consistently in the range of 60-64% for glucose-grown cultures during logarithmic growth but declined in stationary cultures. Overall, hydrogen conversion efficiencies for glucose cultures were 23% based on the assumption of a maximum of 4 mol of hydrogen/ mol of glucose. Hydrogen conversion efficiencies were similar for sucrose (23%) and somewhat lower for molasses (15%) but were much lower for lactate (0.50%) and cellulose (0.075%).

  13. The production and use of hydrogen in the future

    Science.gov (United States)

    Avsec, Jurij

    2017-07-01

    Efficient and sustainable methods of clean fuel production are needed in all countries of the world in the face of depleting oil reserves and the need to reduce carbon dioxide emissions. With hydrogen technology we can significantly reduce harmful emissions in air and water. However, a key missing element is a large-scale method of hydrogen production from water. As a carbon-based technology, the predominant existing process (steam-methane reforming (SMR)) is unsuitable regarding global warming, icreased world population, etc. This paper focuses on a production of hydrogen in connection with a thermal power plant. We will show the technologies which allow the coupling between a thermal power plant and hydrogen technologies.

  14. Bio-hydrogen Production Potential from Market Waste

    Directory of Open Access Journals (Sweden)

    Lanna Jaitalee

    2010-07-01

    Full Text Available This research studied bio-hydrogen production from vegetable waste from a fresh market in order to recover energy. A series of batch experiments were conducted to investigate the effects of initial volatile solids concentration on the bio-hydrogen production process. Lab bench scale anaerobic continuous stirred-tank reactors (CSTR were used to study the effect of substrate and sludge inoculation on hydrogen production. Three different concentrations of initial total volatile solids (TVS of organic waste were varied from 2%, 3% and 5% respectively. The pH was controlled at 5.5 for all batches in the experiment. The results showed that bio-hydrogen production depended on feed-substrate concentration. At initial TVS content of 3%, the highest hydrogen production was achieved at a level of 0.59 L-H2/L at pH 5.5. The maximum hydrogen yield was 15.3 ml H2/g TVS or 8.5 ml H2/g COD. The composition of H2 in the biogas ranged from 28.1-30.9% and no CH4 was detected in all batch tests.

  15. Radiolytic Hydrogen Production in the Subseafloor Basaltic Aquifer.

    Science.gov (United States)

    Dzaugis, Mary E; Spivack, Arthur J; Dunlea, Ann G; Murray, Richard W; D'Hondt, Steven

    2016-01-01

    Hydrogen (H2) is produced in geological settings by dissociation of water due to radiation from radioactive decay of naturally occurring uranium ((238)U, (235)U), thorium ((232)Th) and potassium ((40)K). To quantify the potential significance of radiolytic H2 as an electron donor for microbes within the South Pacific subseafloor basaltic aquifer, we use radionuclide concentrations of 43 basalt samples from IODP Expedition 329 to calculate radiolytic H2 production rates in basement fractures. The samples are from three sites with very different basement ages and a wide range of alteration types. U, Th, and K concentrations vary by up to an order of magnitude from sample to sample at each site. Comparison of our samples to each other and to the results of previous studies of unaltered East Pacific Rise basalt suggests that significant variations in radionuclide concentrations are due to differences in initial (unaltered basalt) concentrations (which can vary between eruptive events) and post-emplacement alteration. However, there is no clear relationship between alteration type and calculated radiolytic yields. Local maxima in U, Th, and K produce hotspots of H2 production, causing calculated radiolytic rates to differ by up to a factor of 80 from sample to sample. Fracture width also greatly influences H2 production, where microfractures are hotspots for radiolytic H2 production. For example, H2 production rates normalized to water volume are 190 times higher in 1 μm wide fractures than in fractures that are 10 cm wide. To assess the importance of water radiolysis for microbial communities in subseafloor basaltic aquifers, we compare electron transfer rates from radiolysis to rates from iron oxidation in subseafloor basalt. Radiolysis appears likely to be a more important electron donor source than iron oxidation in old (>10 Ma) basement basalt. Radiolytic H2 production in the volume of water adjacent to a square cm of the most radioactive SPG basalt may support as

  16. Radiolytic Hydrogen Production in the Subseafloor Basaltic Aquifer

    Science.gov (United States)

    Dzaugis, Mary E.; Spivack, Arthur J.; Dunlea, Ann G.; Murray, Richard W.; D’Hondt, Steven

    2016-01-01

    Hydrogen (H2) is produced in geological settings by dissociation of water due to radiation from radioactive decay of naturally occurring uranium (238U, 235U), thorium (232Th) and potassium (40K). To quantify the potential significance of radiolytic H2 as an electron donor for microbes within the South Pacific subseafloor basaltic aquifer, we use radionuclide concentrations of 43 basalt samples from IODP Expedition 329 to calculate radiolytic H2 production rates in basement fractures. The samples are from three sites with very different basement ages and a wide range of alteration types. U, Th, and K concentrations vary by up to an order of magnitude from sample to sample at each site. Comparison of our samples to each other and to the results of previous studies of unaltered East Pacific Rise basalt suggests that significant variations in radionuclide concentrations are due to differences in initial (unaltered basalt) concentrations (which can vary between eruptive events) and post-emplacement alteration. However, there is no clear relationship between alteration type and calculated radiolytic yields. Local maxima in U, Th, and K produce hotspots of H2 production, causing calculated radiolytic rates to differ by up to a factor of 80 from sample to sample. Fracture width also greatly influences H2 production, where microfractures are hotspots for radiolytic H2 production. For example, H2 production rates normalized to water volume are 190 times higher in 1 μm wide fractures than in fractures that are 10 cm wide. To assess the importance of water radiolysis for microbial communities in subseafloor basaltic aquifers, we compare electron transfer rates from radiolysis to rates from iron oxidation in subseafloor basalt. Radiolysis appears likely to be a more important electron donor source than iron oxidation in old (>10 Ma) basement basalt. Radiolytic H2 production in the volume of water adjacent to a square cm of the most radioactive SPG basalt may support as many as

  17. Radiolytic hydrogen production in the subseafloor basaltic aquifer

    Directory of Open Access Journals (Sweden)

    Mary E Dzaugis

    2016-02-01

    Full Text Available Hydrogen (H2 is produced in geological settings by dissociation of water due to radiation from radioactive decay of naturally occurring uranium (238U, 235U, thorium (232Th and potassium (40K. To quantify the potential significance of radiolytic H2 as an electron donor for microbes within the South Pacific subseafloor basaltic aquifer, we use radionuclide concentrations of 43 basalt samples from IODP Expedition 329 to calculate radiolytic H2 production rates in basement fractures. The samples are from three sites with very different basement ages and a wide range of alteration types. U, Th and K concentrations vary by up to an order of magnitude from sample to sample at each site. Comparison of our samples to each other and to the results of previous studies of unaltered East Pacific Rise basalt suggests that significant variations in radionuclide concentrations are due to differences in initial (unaltered basalt concentrations (which can vary between eruptive events and post-emplacement alteration. In our samples, there is no clear relationship between alteration type and calculated radiolytic yields. Local maxima in U, Th, and K produce hotspots of H2 production, causing calculated radiolytic rates to differ by up to a factor of 80 from sample to sample. Fracture width also greatly influences H2 production, where microfractures are hotspots for radiolytic H2 production. For example, H2 production rates normalized to water volume are 190 times higher in 1 μm wide fractures than in fractures that are 10 cm wide. To assess the importance of water radiolysis for microbial communities in subseafloor basaltic aquifers, we compare electron transfer rates from radiolysis to rates from iron oxidation in subseafloor basalt. Radiolysis appears likely to be a more important electron donor source than iron oxidation in old (>10 Ma basement basalt. Radiolytic H2 production in the volume of water adjacent to a square cm of the most radioactive SPG basalt may

  18. Aerobic Hydrogen Production via Nitrogenase in Azotobacter vinelandii CA6

    Science.gov (United States)

    Noar, Jesse; Loveless, Telisa; Navarro-Herrero, José Luis; Olson, Jonathan W.

    2015-01-01

    The diazotroph Azotobacter vinelandii possesses three distinct nitrogenase isoenzymes, all of which produce molecular hydrogen as a by-product. In batch cultures, A. vinelandii strain CA6, a mutant of strain CA, displays multiple phenotypes distinct from its parent: tolerance to tungstate, impaired growth and molybdate transport, and increased hydrogen evolution. Determining and comparing the genomic sequences of strains CA and CA6 revealed a large deletion in CA6's genome, encompassing genes related to molybdate and iron transport and hydrogen reoxidation. A series of iron uptake analyses and chemostat culture experiments confirmed iron transport impairment and showed that the addition of fixed nitrogen (ammonia) resulted in cessation of hydrogen production. Additional chemostat experiments compared the hydrogen-producing parameters of different strains: in iron-sufficient, tungstate-free conditions, strain CA6's yields were identical to those of a strain lacking only a single hydrogenase gene. However, in the presence of tungstate, CA6 produced several times more hydrogen. A. vinelandii may hold promise for developing a novel strategy for production of hydrogen as an energy compound. PMID:25911479

  19. Hydrogen Production from Semiconductor-based Photocatalysis via Water Splitting

    Directory of Open Access Journals (Sweden)

    Jeffrey C. S. Wu

    2012-10-01

    Full Text Available Hydrogen is the ideal fuel for the future because it is clean, energy efficient, and abundant in nature. While various technologies can be used to generate hydrogen, only some of them can be considered environmentally friendly. Recently, solar hydrogen generated via photocatalytic water splitting has attracted tremendous attention and has been extensively studied because of its great potential for low-cost and clean hydrogen production. This paper gives a comprehensive review of the development of photocatalytic water splitting for generating hydrogen, particularly under visible-light irradiation. The topics covered include an introduction of hydrogen production technologies, a review of photocatalytic water splitting over titania and non-titania based photocatalysts, a discussion of the types of photocatalytic water-splitting approaches, and a conclusion for the current challenges and future prospects of photocatalytic water splitting. Based on the literatures reported here, the development of highly stable visible–light-active photocatalytic materials, and the design of efficient, low-cost photoreactor systems are the key for the advancement of solar-hydrogen production via photocatalytic water splitting in the future.

  20. An assessment on hydrogen production using central receiver solar systems

    Science.gov (United States)

    Bilgen, C.; Bilgen, E.

    An assessment is presented on hydrogen production using a dedicated central receiver solar system concept coupled to two types of hydrogen producing processes, electrolysis and thermochemical. The study on solar electrolytic hydrogen was carried out using solar electricity and four different electrolytic technologies, namely, industrial unipolar 1980 and 1983 technologies, industrial bipolar and solid polymer electrolyte technology. The thermochemical process was the sulphur/iodine cycle, which is being developed by General Atomic Co. Systems, which is capable of producing about one-million GJ hydrogen per year, was developed at the conceptual level, and site specific computations were carried out. A general mathematical model was developed to predict the optical and thermal performance of the central receiver system coupled directly to the chemical plant. Cost models were developed for each subsystem based on the database published in the literature. Levelized and delevelized costs of solar hydrogen were then computed.

  1. Hydrogen production from wastewater sludge using a Clostridium strain.

    Science.gov (United States)

    Wang, C C; Chang, C W; Chu, C P; Lee, D J; Chang, B V; Liao, C S

    2003-09-01

    Limited data in literature revealed a relatively low hydrogen yield from wastewater sludge, ca. 0.16 mg/g-dried solids, using anaerobic fermentation. We demonstrated in this work a much higher hydrogen yield, around 1.1 mg-H2/g-dried solids using a clostridium strain isolated from the sludge sample. The formed hydrogen would be consumed after passing the peak value at around 30-36 h of fermentation. We examined the effects of employing five different pre-treatments on substrate sludge, but noted no appreciable enhancement in hydrogen yield as commonly expected for methane production. Since a vast amount of organic matters had been released to water after hydrogen fermentation, we externally dosed methanogenic bacteria to the fermented liquor to produce methane. The fermented liquor could produce more methane than the non-fermented sample, indicating that the dosed methanogenic bacteria readily utilized the organic matters derived from the fermentation test.

  2. Inter-esterified palm products as alternatives to hydrogenation.

    Science.gov (United States)

    Idris, Nor Aini; Dian, Noor Lida Habi Mat

    2005-01-01

    Inter-esterification is one of the processes used to modify the physico-chemical characteristics of oils and fats. Inter-esterification is an acyl-rearrangement reaction on the glycerol molecule. On the other hand, hydrogenation involves addition of hydrogen to the double bonds of unsaturated fatty acids. Due to health implications of trans fatty acids, which are formed during hydrogenation, the industry needs to find alternatives to hydrogenated fats. This paper discusses some applications of inter-esterified fats, with particular reference to inter-esterified palm products, as alternatives to hydrogenation. Some physico-chemical properties of inter-esterified fats used in shortenings are discussed. With inter-esterification, more palm stearin can be incorporated in vanaspati. For confectionary fats and infant formulations, enzymatic inter-esterification has been employed.

  3. Onboard Plasmatron Hydrogen Production for Improved Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Daniel R. Cohn; Leslie Bromberg; Kamal Hadidi

    2005-12-31

    A plasmatron fuel reformer has been developed for onboard hydrogen generation for vehicular applications. These applications include hydrogen addition to spark-ignition internal combustion engines, NOx trap and diesel particulate filter (DPF) regeneration, and emissions reduction from spark ignition internal combustion engines First, a thermal plasmatron fuel reformer was developed. This plasmatron used an electric arc with relatively high power to reform fuels such as gasoline, diesel and biofuels at an oxygen to carbon ratio close to 1. The draw back of this device was that it has a high electric consumption and limited electrode lifetime due to the high temperature electric arc. A second generation plasmatron fuel reformer was developed. It used a low-current high-voltage electric discharge with a completely new electrode continuation. This design uses two cylindrical electrodes with a rotating discharge that produced low temperature volumetric cold plasma., The lifetime of the electrodes was no longer an issue and the device was tested on several fuels such as gasoline, diesel, and biofuels at different flow rates and different oxygen to carbon ratios. Hydrogen concentration and yields were measured for both the thermal and non-thermal plasmatron reformers for homogeneous (non-catalytic) and catalytic reforming of several fuels. The technology was licensed to an industrial auto part supplier (ArvinMeritor) and is being implemented for some of the applications listed above. The Plasmatron reformer has been successfully tested on a bus for NOx trap regeneration. The successful development of the plasmatron reformer and its implementation in commercial applications including transportation will bring several benefits to the nation. These benefits include the reduction of NOx emissions, improving engine efficiency and reducing the nation's oil consumption. The objective of this program has been to develop attractive applications of plasmatron fuel reformer

  4. Using short pulses to enhance the production rate of vibrationally excited hydrogen molecules in hydrogen discharge

    Institute of Scientific and Technical Information of China (English)

    Sun Ji-Zhong; Li Xian-Tao; Bai Jing; Wang De-Zhen

    2012-01-01

    Hydrogen discharges driven by the combined radio-frequency(rf)/short pulse sources are investigated using the particle-in-cell method.The simulation results show that the discharge driven additionally by the short pulse can enhance the electron density and modulate the electron energy to provide a better condition for negative hydrogen ion production than the discharge driven by the rf-only source.

  5. Technoeconomic analysis of renewable hydrogen production, storage, and detection systems

    Energy Technology Data Exchange (ETDEWEB)

    Mann, M.K.; Spath, P.L.; Kadam, K. [National Renewable Energy Lab., Golden, CO (United States)

    1996-10-01

    Technical and economic feasibility studies of different degrees of completeness and detail have been performed on several projects being funded by the Department of Energy`s Hydrogen Program. Work this year focused on projects at the National Renewable Energy Laboratory, although analyses of projects at other institutions are underway or planned. Highly detailed analyses were completed on a fiber optic hydrogen leak detector and a process to produce hydrogen from biomass via pyrolysis followed by steam reforming of the pyrolysis oil. Less detailed economic assessments of solar and biologically-based hydrogen production processes have been performed and focused on the steps that need to be taken to improve the competitive position of these technologies. Sensitivity analyses were conducted on all analyses to reveal the degree to which the cost results are affected by market changes and technological advances. For hydrogen storage by carbon nanotubes, a survey of the competing storage technologies was made in order to set a baseline for cost goals. A determination of the likelihood of commercialization was made for nearly all systems examined. Hydrogen from biomass via pyrolysis and steam reforming was found to have significant economic potential if a coproduct option could be co-commercialized. Photoelectrochemical hydrogen production may have economic potential, but only if low-cost cells can be modified to split water and to avoid surface oxidation. The use of bacteria to convert the carbon monoxide in biomass syngas to hydrogen was found to be slightly more expensive than the high end of currently commercial hydrogen, although there are significant opportunities to reduce costs. Finally, the cost of installing a fiber-optic chemochromic hydrogen detection system in passenger vehicles was found to be very low and competitive with alternative sensor systems.

  6. Bacterial bioaugmentation for improving methane and hydrogen production from microalgae

    Science.gov (United States)

    2013-01-01

    Background The recalcitrant cell walls of microalgae may limit their digestibility for bioenergy production. Considering that cellulose contributes to the cell wall recalcitrance of the microalgae Chlorella vulgaris, this study investigated bioaugmentation with a cellulolytic and hydrogenogenic bacterium, Clostridium thermocellum, at different inoculum ratios as a possible method to improve CH4 and H2 production of microalgae. Results Methane production was found to increase by 17?~?24% with the addition of C. thermocellum, as a result of enhanced cell disruption and excess hydrogen production. Furthermore, addition of C. thermocellum enhanced the bacterial diversity and quantities, leading to higher fermentation efficiency. A two-step process of addition of C. thermocellum first and methanogenic sludge subsequently could recover both hydrogen and methane, with a 9.4% increase in bioenergy yield, when compared with the one-step process of simultaneous addition of C. thermocellum and methanogenic sludge. The fluorescence peaks of excitation-emission matrix spectra associated with chlorophyll can serve as biomarkers for algal cell degradation. Conclusions Bioaugmentation with C. thermocellum improved the degradation of C. vulgaris biomass, producing higher levels of methane and hydrogen. The two-step process, with methanogenic inoculum added after the hydrogen production reached saturation, was found to be an energy-efficiency method for hydrogen and methane production. PMID:23815806

  7. A study on the solar hydrogen production techniques

    Energy Technology Data Exchange (ETDEWEB)

    Bozoglan, Elif [Department of Management, Taris Olive Oil, Agricultural, Industrial and Commercial Company, (Turkey); Midilli, Adnan [Energy Technologies, Turgut Kiran Maritime College, Marine Engineering, Rize University (Turkey); Hepbasli, Arif [Department of Mechanical Engineering, College of Engineering, King Saud University (Saudi Arabia)

    2011-07-01

    With the depletion of fossil fuels and the rising concerns about the environment, interest in green energy, which is both sustainable and clean, is growing. Among the different techniques, solar energy based hydrogen production appears to be one of the simpler and more convenient methods. Several solar hydrogen production methods exist and the aim of this paper is to determine the environmental and sustainability performances of an electrolyser. A solar hydrogen system was designed to meet the demands of 100 families in Misurata, Libya, whose average consumption is 268 kW and an exergy analysis was performed on the system. Results showed that the exergy destruction factor was 0.14 and the environmental destruction factor was 0.16. This study demonstrated that producing hydrogen using solar energy is an environmentally friendly and sustainable method which does not generate any greenhouse gases in the operating stage.

  8. Protons and pleomorphs: aerobic hydrogen production in Azotobacters.

    Science.gov (United States)

    Noar, Jesse D; Bruno-Bárcena, José M

    2016-02-01

    As obligate aerobic soil organisms, the ability of Azotobacter species to fix nitrogen is unusual given that the nitrogenase complex requires a reduced cellular environment. Molecular hydrogen is an unavoidable byproduct of the reduction of dinitrogen; at least one molecule of H2 is produced for each molecule of N2 fixed. This could be considered a fault in nitrogenase efficiency, essentially a waste of energy and reducing equivalents. Wild-type Azotobacter captures this hydrogen and oxidizes it with its membrane-bound uptake hydrogenase complex. Strains lacking an active hydrogenase complex have been investigated for their hydrogen production capacities. What is the role of H2 in the energy metabolism of nitrogen-fixing Azotobacter? Is hydrogen production involved in Azotobacter species' protection from or tolerance to oxygen, or vice versa? What yields of hydrogen can be expected from hydrogen-evolving strains? Can the yield of hydrogen be controlled or increased by changing genetic, environmental, or physiological conditions? We will address these questions in the following mini-review.

  9. The Solar Wind Charge-Exchange Production Factor for Hydrogen

    CERN Document Server

    Kuntz, K D; Collier, M R; Connor, H K; Cravens, T E; Koutroumpa, D; Porter, F S; Robertson, I P; Sibeck, D G; Snowden, S L; Thomas, N E; Wash, B M

    2015-01-01

    The production factor, or broad band averaged cross-section, for solar wind charge-exchange with hydrogen producing emission in the ROSAT 1/4 keV (R12) band is $3.8\\pm0.2\\times10^{-20}$ count degree$^{-2}$ cm$^4$. This value is derived from a comparison of the Long-Term (background) Enhancements in the ROSAT All-Sky Survey with magnetohysdrodynamic simulations of the magnetosheath. This value is 1.8 to 4.5 times higher than values derived from limited atomic data, suggesting that those values may be missing a large number of faint lines. This production factor is important for deriving the exact amount of 1/4 keV band flux that is due to the Local Hot Bubble, for planning future observations in the 1/4 keV band, and for evaluating proposals for remote sensing of the magnetosheath. The same method cannot be applied to the 3/4 keV band as that band, being composed primarily of the oxygen lines, is far more sensitive to the detailed abundances and ionization balance in the solar wind. We also show, incidentally,...

  10. Hydrogen Production Costs of Various Primary Energy Sources

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Jae Hyuk; Tak, Nam Il; Kim, Yong Hee; Park, Won Seok

    2005-11-15

    Many studies on the economical aspects of hydrogen energy technologies have been conducted with the increase of the technical and socioeconomic importance of the hydrogen energy. However, there is still no research which evaluates the economy of hydrogen production from the primary energy sources in consideration of Korean situations. In this study, the hydrogen production costs of major primary energy sources are compared in consideration of the Korean situations such as feedstock price, electricity rate, and load factor. The evaluation methodology is based on the report of the National Academy of Science (NAS) of U.S. The present study focuses on the possible future technology scenario defined by NAS. The scenario assumes technological improvement that may be achieved if present research and development (R and D) programs are successful. The production costs by the coal and natural gas are 1.1 $/kgH{sub 2} and 1.36 $/kgH{sub 2}, respectively. However, the fossil fuels are susceptible to the price variation depending on the oil and the raw material prices, and the hydrogen production cost also depends on the carbon tax. The economic competitiveness of the renewable energy sources such as the wind, solar, and biomass are relatively low when compared with that of the other energy sources. The estimated hydrogen production costs from the renewable energy sources range from 2.35 $/kgH{sub 2} to 6.03 $/kgH{sub 2}. On the other hand, the production cost by nuclear energy is lower than that of natural gas or coal when the prices of the oil and soft coal are above $50/barrel and 138 $/ton, respectively. Taking into consideration the recent rapid increase of the oil and soft coal prices and the limited fossil resource, the nuclear-hydrogen option appears to be the most economical way in the future.

  11. Production of hydrogen by thermocatalytic cracking of natural gas

    Energy Technology Data Exchange (ETDEWEB)

    Muradov, N. [Florida Solar Energy Center, Cocoa, FL (United States)

    1996-10-01

    The conventional methods of hydrogen production from natural gas (for example, steam reforming and partial oxidation) are complex, multi-step processes that produce large quantities of CO{sub 2}. The main goal of this project is to develop a technologically simple process for hydrogen production from natural gas (NG) and other hydrocarbon fuels via single-step decomposition of hydrocarbons. This approach eliminates or significantly reduces CO{sub 2} emission. Carbon is a valuable by-product of this process, whereas conventional methods of hydrogen production from NG produce no useful by-products. This approach is based on the use of special catalysts that reduce the maximum temperature of the process from 1400-1500{degrees}C (thermal non-catalytic decomposition of methane) to 500-900{degrees}C. Transition metal based catalysts and various forms of carbon are among the candidate catalysts for the process. This approach can advantageously be used for the development of compact NG reformers for on-site production of hydrogen-methane blends at refueling stations and, also, for the production of hydrogen-rich gas for fuel cell applications. The author extended the search for active methane decomposition catalysts to various modifications of Ni-, Fe-, Mo- and Co-based catalysts. Variation in the operational parameters makes it possible to produce H{sub 2}-CH{sub 4} blends with a wide range of hydrogen concentrations that vary from 15 to 98% by volume. The author found that Ni-based catalysts are more effective at temperatures below 750{degrees}C, whereas Fe-based catalysts are effective at temperatures above 800{degrees}C for the production of hydrogen with purity of 95% v. or higher. The catalytic pyrolysis of liquid hydrocarbons (pentane, gasoline) over Fe-based catalyst was conducted. The author observed the production of a hydrogen-rich gas (hydrogen concentration up to 97% by volume) at a rate of approximately 1L/min.mL of hydrocarbon fuel.

  12. Effect of inoculum conditioning on hydrogen fermentation and pH effect on bacterial community relevant to hydrogen production.

    Science.gov (United States)

    Kawagoshi, Yasunori; Hino, Naoe; Fujimoto, Aya; Nakao, Masaharu; Fujita, Yukiko; Sugimura, Seiji; Furukawa, Kenji

    2005-11-01

    The effect of conditioning for a variety of inoculums on fermentative hydrogen production was investigated. In addition, the effects of pH condition on hydrogen fermentation and bacterial community were investigated. The effect of conditioning on hydrogen production was different depending on the inoculum types. An appreciable hydrogen production was shown with anaerobic digested sludge and lake sediment without conditioning, however, no hydrogen was produced when refuse compost and kiwi grove soil were used as inoculums without conditioning. The highest hydrogen production was obtained with heat-conditioned anaerobic digested sludge, almost the same production was also obtained with unconditioned digested sludge. The pH condition considerably affected hydrogen fermentation, hydrogen gas was efficiently produced with unconditioned anaerobic sludge when the pH was controlled at 6.0 throughout the culture period and not when only the initial pH was adjusted to 6.0 and 7.0. Hydrogen production decreased when the culture pH was only adjusted at the beginning of each batch in continuous batch culture, and additionally, bacterial community varied with the change in hydrogen production. It was suggested that Clostridium and Coprothermobacter species played important role in hydrogen fermentation, and Lactobacillus species had an adverse effect on hydrogen production.

  13. Discovery of Photocatalysts for Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    D. Brent MacQueen

    2006-10-01

    This project for DOE was designed to address these materials-related issues through a combination of high-throughput screening of semiconductor candidates and theoretical modeling of nanostructures. High-throughput screening is an effective and economical way to examine a large number of candidates and identify those worthy of further study. Unfortunately, in the course of this project, we discovered no semiconductor candidates that can meet the DOE’s stringent requirements for an economically feasible photoelectrochemical process. However, some of our results indicated that several systems may have potential if further optimized. In particular, the published theoretical modeling work indicates that core-shell nanorod structures, if properly engineered, have the potential to overcome the shortfalls of current semiconductors. Although the synthesis of the designed core-shell nanorod structures proved to be beyond the current capabilities of our laboratories, recent advances in the synthesis of core-shell nanorod structures imply that the designed structures can be synthesized. SRI is confident that once these materials are made they will validate our models and lead to economical and environmentally friendly hydrogen from sunlight and water. The high-throughput photolysis analysis module developed at SRI will also have utility in applications such as identifying catalysts for photo-assisted chemical detoxification, as well as non-photolytic applications such as hydrogen storage, which can take advantage of the ability of the analysis module to monitor pressure over time.

  14. Engineering analysis of potential photosynthetic bacterial hydrogen-production systems

    Science.gov (United States)

    Herlevich, A.; Karpuk, M. E.

    1982-06-01

    Photosynthetic bacteria (PSB) are capable of generating hydrogen from organics in effluents from food processing, pulp and paper, and chemical and pharmaceutical industries. Hydrogen evolution takes place under light in the absence of air. The rate of hydrogen production is expected to range between 300 to 600 scf of hydrogen per 1000 galloons of waste stream treated per hour. This hydrogen production system has been demonstrated at a bench-scale level and is ready for engineering development. A conceptual design for a PSB hydrogen production system is described. The system is expected to be sited adjacent to a waste stream source which will be pretreated by fermentation and pH adjustment, innoculated with bacteria, and then passed into the reactor. The reactor effluent can either be discharged into a rapid infiltration system, an irrigation ditch, and/or recycled back into the reactor. Several potential reactor designs have been developed, analyzed, and costed. A large covered pond appears to be the most economical design approach.

  15. Microbial production of hydrogen from starch-manufacturing wastes

    Energy Technology Data Exchange (ETDEWEB)

    Yokoi, H.; Maki, R.; Hirose, J.; Hayashi, S. [Miyazaki Univ. (Japan). Dept. of Applied Chemistry

    2002-05-01

    Effective hydrogen production from starch-manufacturing wastes by microorganisms was investigated. Continuous hydrogen production in high yield of 2.7 mol H{sub 2} mol{sup -1} glucose was attained by a mixed culture of Clostridium butyricum and Enterobacter aerogenes HO-39 in the starch waste medium consisting of sweet potato starch residue as a carbon source and corn steep liquor as a nitrogen source in a repeated batch culture. Rhodobacter sp. M-19 could produce hydrogen from the supernatant of the culture broth obtained in the repeated batch culture of C. butyricum and E. aerogenes HO-39. Hydrogen yield of 4.5 mol H{sub 2} mol{sup -1} glucose was obtained by culturing Rhodobacter sp. M-19 in the supernatant supplemented with 20{mu}gl{sup -1} Na{sub 2}MoO{sub 4} 2H{sub 2}O and 10mgl{sup -1} EDTA in a repeated batch culture with pH control at 7.5. Therefore, continuous hydrogen production with total hydrogen yield of 7.2 mol H{sub 2} mol{sup -1} glucose from the starch remaining in the starch residue was attained by the repeated batch culture with C. butyricum and E. aerogenes HO-39 and by the successive repeated batch culture with Rhodobacter sp. M-19. (Author)

  16. Hydrogen production and storage: R & D priorities and gaps

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-05-04

    This review of priorities and gaps in hydrogen production and storage R & D has been prepared by the IEA Hydrogen Implementing Agreement in the context of the activities of the IEA Hydrogen Co-ordination Group. It includes two papers. The first is by Trygve Riis, Elisabet F. Hagen, Preben J.S. Vie and Oeystein Ulleberg. This offers an overview of the technologies for hydrogen production. The technologies discussed are reforming of natural gas; gasification of coal and biomass; and the splitting of water by water-electrolysis, photo-electrolysis, photo-biological production and high-temperature decomposition. The second paper is by Trygve Riis, Gary Sandrock, Oeystein Ulleberg and Preben J.S. Vie. The objective of this paper is to provide a brief overview of the possible hydrogen storage options available today and in the foreseeable future. Hydrogen storage can be considered for onboard vehicular, portable, stationary, bulk, and transport applications, but the main focus of this paper is on vehicular storage, namely fuel cell or ICE/electric hybrid vehicles. 7 refs., 24 figs., 14 tabs.

  17. Photosynthetic hydrogen and oxygen production by green algae

    Energy Technology Data Exchange (ETDEWEB)

    Greenbaum, E.; Lee, J.W.

    1997-12-31

    An overview of photosynthetic hydrogen and oxygen production by green algae in the context of its potential as a renewable chemical feed stock and energy carrier is presented. Beginning with its discovery by Gaffron and Rubin in 1942, motivated by curiosity-driven laboratory research, studies were initiated in the early 1970s that focused on photosynthetic hydrogen production from an applied perspective. From a scientific and technical point of view, current research is focused on optimizing net thermodynamic conversion efficiencies represented by the Gibbs Free Energy of molecular hydrogen. The key research questions of maximizing hydrogen and oxygen production by light-activated water splitting in green algae are (1) removing the oxygen sensitivity of algal hydrogenases; (2) linearizing the light saturation curves of photosynthesis throughout the entire range of terrestrial solar irradiance--including the role of bicarbonate and carbon dioxide in optimization of photosynthetic electron transport and (3) the minimum number of light reactions that are required to split water to elemental hydrogen and oxygen. Each of these research topics is being actively addressed by the photobiological hydrogen research community.

  18. Optimal control strategies for hydrogen production when coupling solid oxide electrolysers with intermittent renewable energies

    Science.gov (United States)

    Cai, Qiong; Adjiman, Claire S.; Brandon, Nigel P.

    2014-12-01

    The penetration of intermittent renewable energies requires the development of energy storage technologies. High temperature electrolysis using solid oxide electrolyser cells (SOECs) as a potential energy storage technology, provides the prospect of a cost-effective and energy efficient route to clean hydrogen production. The development of optimal control strategies when SOEC systems are coupled with intermittent renewable energies is discussed. Hydrogen production is examined in relation to energy consumption. Control strategies considered include maximizing hydrogen production, minimizing SOEC energy consumption and minimizing compressor energy consumption. Optimal control trajectories of the operating variables over a given period of time show feasible control for the chosen situations. Temperature control of the SOEC stack is ensured via constraints on the overall temperature difference across the cell and the local temperature gradient within the SOEC stack, to link materials properties with system performance; these constraints are successfully managed. The relative merits of the optimal control strategies are analyzed.

  19. Kinetic study of biological hydrogen production by anaerobic fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Sangeetha, R. [Annamalai Univ., Chidambaram (India). Dept. of Chemical Engineering; Karunanithi, T. [Annamalai Univ., Tamilnadu (India). Dept. of Chemical Engineering

    2009-07-01

    This study examined the kinetics of batch biohydrogen production from glucose. Clostridium pasteurianum was used to produce biohydrogen by dark anaerobic fermentation. The initial substrate concentration, initial pH and temperature were optimized for biohydrogen production. The maximum production of hydrogen under optimum conditions was found to be 5.376 l/l. The kinetic parameters were determined for the optimized medium and conditions in the batch reactor. The by product was expressed as total acidic equivalent. This presentation discussed the logistic equation that was used to model the growth of the organism and described how the kinetic parameters were calculated. The Leudeking piret kinetic model was used to express the hydrogen production and substrate use because it combines both growth associated and non associated contributions. It was concluded the production of biohydrogen can be predicted well using the logistic model for cell growth kinetics and the logistic incorporated Leudeking Piret model for product and substrate utilization kinetics.

  20. EVermont Renewable Hydrogen Production and Transportation Fueling System

    Energy Technology Data Exchange (ETDEWEB)

    Garabedian, Harold T.

    2008-03-30

    A great deal of research funding is being devoted to the use of hydrogen for transportation fuel, particularly in the development of fuel cell vehicles. When this research bears fruit in the form of consumer-ready vehicles, will the fueling infrastructure be ready? Will the required fueling systems work in cold climates as well as they do in warm areas? Will we be sure that production of hydrogen as the energy carrier of choice for our transit system is the most energy efficient and environmentally friendly option? Will consumers understand this fuel and how to handle it? Those are questions addressed by the EVermont Wind to Wheels Hydrogen Project: Sustainable Transportation. The hydrogen fueling infrastructure consists of three primary subcomponents: a hydrogen generator (electrolyzer), a compression and storage system, and a dispenser. The generated fuel is then used to provide transportation as a motor fuel. EVermont Inc., started in 1993 by then governor Howard Dean, is a public-private partnership of entities interested in documenting and advancing the performance of advanced technology vehicles that are sustainable and less burdensome on the environment, especially in areas of cold climates, hilly terrain and with rural settlement patterns. EVermont has developed a demonstration wind powered hydrogen fuel producing filling system that uses electrolysis, compression to 5000 psi and a hydrogen burning vehicle that functions reliably in cold climates. And that fuel is then used to meet transportation needs in a hybrid electric vehicle whose internal combustion engine has been converted to operate on hydrogen Sponsored by the DOE EERE Hydrogen, Fuel Cells & Infrastructure Technologies (HFC&IT) Program, the purpose of the project is to test the viability of sustainably produced hydrogen for use as a transportation fuel in a cold climate with hilly terrain and rural settlement patterns. Specifically, the project addresses the challenge of building a renewable

  1. Photovoltaic hydrogen production with commercial alkaline electrolysers

    Energy Technology Data Exchange (ETDEWEB)

    Ursua, A.; Lopez, J.; Gubia, E.; Marroyo, L.; Sanchis, P. [Public Univ. of Navarra, Pamplona (Spain). Dept. of Electric and Electronic Engineering

    2010-07-01

    Renewable energy sources and Electrolysis generate the so-called green Hydrogen, a zero-emission and potentially fossil fuel independent energy source. However, the inherent variability of the renewable energy sources implies a mode of operation for which most current electrolysers have not been designed. This paper analyses the operation of a water electrolyser fed with photovoltaic (PV) generator electric profile. The system, Integrated by a 1 Nm{sup 3}/h Hydrogenics alkaline electrolyser and a 5100 W PV generator with 60 BP585 modules, is installed at the Public University of Navarra (Spain). The PV generator profile fed to the electrolyser is emulated by a custom-made apparatus designed and built by the authors of this paper. The profile is designed according to real irradiance data measured by a calibration cell. The irradiance data are converted to the electric power profile that the PV generator would have delivered in case of having been connected to the electrolyser by means of a DC/DC converter with maximum power point tracking (MPPT). Finally, from previously measured power-current electrolyser characteristic curves, the current profile to be delivered to the electrolyser is obtained and programmed to the electronic device. The electrolyser was tested for two types of days. During the first day, the irradiance was very stable, whereas during the second day, the irradiance was very variable. The experimental results show an average power consumption rate and an efficiency of 4908 Wh/Nm{sup 3} and 72.1%, on the first day, and 4842 Wh/Nm{sup 3} and 73.3% on the second day. The electrolyser performance was particularly good in spite of the high variability of the electric supply of the second day. (orig.)

  2. Media Improvement for Hydrogen Production Using C. acetobutylicum NCIMB 13357

    Directory of Open Access Journals (Sweden)

    Mohd S. Kalil

    2009-01-01

    Full Text Available Problem statement: Some component of fermentation medium showed to reduce the bacterial production of hydrogen. Approach: Reinforced clostridium medium is a selected medium for Clostridium species. Reformulation this medium regarding hydrogen production may focus on such medium composition that enhance or reduce the bacterial productivity. The optimum pH and temperature for hydrogen production were at initial pH of 7.0 and 30°C. Results: The results show that both nitrogen source and its concentration affected biomass growth as well as H2 yield. Yeast extract at concentration of 13 gL-1 was the best organic nitrogen source and resulted in hydrogen yield (YP/S of 308 mL g-1 glucose utilized with biomass concentration of 1.1 gL-1, hydrogen yield per biomass (YP/X of 280 mL g-1 L-1, biomass per substrate utilized (YX/S of 0.22 and produced hydrogen in gram per gram of glucose utilized (YH2/S of 0.0275. C/N of 70 enhanced the YP/S from 308 mL g-1 to 350 mL g-1 glucose utilized with biomass concentration of 1.22 gL-1, YP/X of 287 mL g-1 L-1, YX/S of 0.244 and (YH2/S of 0.03125. In the absence of sodium chloride and sodium acetate further enhanced YP/S from 350 mL g-1 glucose utilized to 391 mL g-1 glucose utilized with maximum hydrogen productivity of 77.5 mL L-1 h-1, whereas RCM medium gave the highest hydrogen productivity of 63.5 mL L-1h-1. Results also show that Sodium Chloride and Sodium Acetate in the medium adversely affect growth. Removal of both components from the medium enhanced the biomass concentration from 1.22-1.34 gL-1, YP/X of 254 mL g-1 L-1, YX/S of 0.268 and (YH2/S of 0.0349. Conclusion: The medium an improved containing (glucose 5 gL-1, Yeast extract gL-1, L-Cystine. HCl 1 gL-1 and Bacteriological agar 0.5 gL-1, was able to enhance the hydrogen productivity.

  3. Effect of ozone pretreatment on hydrogen production from barley straw.

    Science.gov (United States)

    Wu, Jiangning; Ein-Mozaffari, Farhad; Upreti, Simant

    2013-09-01

    Application of ozone technology to lignocellulosic biohydrogen production was explored with a barley straw. Ozone pretreatment effectively degraded the straw lignin and increased reducing sugar yield. A simultaneous enzyme hydrolysis and dark fermentation experiment was conducted using a mixed anaerobic consortium together with saccharification enzymes. Both untreated and ozonated samples produced hydrogen. Compared to the untreated group, hydrogen produced by the groups ozonated for 15, 30, 45 and 90 min increased 99%, 133%, 166% and 94%, respectively. Some inhibitory effect on hydrogen production was observed with the samples ozonated for 90 min, and the inhibition was on the fermentative microorganisms, not the saccharification enzymes. These results demonstrate that production of biohydrogen from barley straw, a lignocellulosic biomass, can be significantly enhanced by ozone pretreatment.

  4. Enhancement of anaerobic hydrogen production by iron and nickel

    Energy Technology Data Exchange (ETDEWEB)

    Karadag, Dogan; Puhakka, Jaakko A. [Department of Chemistry and Bioengineering, Tampere University of Technology, Tampere (Finland)

    2010-08-15

    The effects of iron and nickel on hydrogen (H{sub 2}) production were investigated in a glucose-fed anaerobic Continuous Flow Stirred Tank Reactor (ACSTR). Both iron and nickel improved the reactor performance and H{sub 2} production was enhanced by 71% with the sole iron or nickel supplementation. In all cases, H{sub 2} production yield was increased by lowering both ethanol and total metabolites production and increasing butyrate production. Furthermore, iron and nickel slightly increased biomass production while glucose degradation decreased with the supplementation of nickel. Dynamic changes in bacterial composition as analyzed by 16S rRNA gene-targeted denaturing gradient gel electrophoresis (DGGE) revealed that hydrogen was produced mainly by Clostridium butyricum strains and that nickel addition decreased the microbial diversity. (author)

  5. Enhanced-hydrogen gas production through underground gasification of lignite

    Institute of Scientific and Technical Information of China (English)

    LIU Shu-qin; WANG Yuan-yuan; ZHAO Ke; YANG Ning

    2009-01-01

    Underground coal gasification is one of the clean technologies of in-situ coal utilization. Hydrogen production from underground gasification of lignite was investigated in this study based on simulation experiments. Pyrolysis of lignite, gasification activity, oxygen-steam gasification and the effect of groundwater influx were studied. As well, the advantages of lignite for stable underground gasification were analyzed. The results indicate that lignite has a high activity for gasification. Coal pyrolysis is an important source of hydrogen emission. Under special heating conditions, hydrogen is released from coal seams at temperatures above 350 ℃ and reaches its maximum value between 725 and 825 ℃. Gas with a hydrogen concentration of 40% to 50% can be continuously obtained by oxygen-steam injection at an optimum ratio of steam to oxygen, while lignite properties will ensure stable gasification. Groundwater influx can be utilized for hydrogen preparation under certain geological conditions through pressure control. Therefore, enhanced-hydrogen gas production through underground gasification of lignite has experimentally been proved.

  6. Production of hydrogen in a conventional microwave oven

    Science.gov (United States)

    Nomura, Shinfuku; Toyota, Hiromichi; Mukasa, Shinobu; Yamashita, Hiroshi; Maehara, Tsunehiro; Kawashima, Ayato

    2009-10-01

    Hydrogen is produced by generating in-liquid plasma in a conventional microwave oven. A receiving antenna unit consisting of seven copper rods is placed at the bottom of the reactor furnace in the microwave oven. 2.45 GHz microwave in-liquid plasma can be generated at the tips of the electrodes in the microwave oven. When the n-dodecane is decomposed by plasma, 74% pure hydrogen gas can be achieved with this device. The hydrogen generation efficiency for a 750 W magnetron output is estimated to be approximately 56% of that of the electrolysis of water. Also, in this process up to 4 mg/s of solid carbon can be produced at the same time. The present process enables simultaneous production of hydrogen gas and the carbide in the hydrocarbon liquid.

  7. Studies on membrane acid electrolysis for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Marco Antonio Oliveira da; Linardi, Marcelo; Saliba-Silva, Adonis Marcelo [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Celulas a Combustivel e Hidrogenio], Email: saliba@ipen.br

    2010-07-01

    Hydrogen represents great opportunity to be a substitute for fossil fuels in the future. Water as a renewable source of hydrogen is of great interest, since it is abundant and can decompose, producing only pure H{sub 2} and O{sub 2}. This decomposition of water can be accomplished by processes such as electrolysis, thermal decomposition and thermochemical cycles. The electrolysis by membrane has been proposed as a viable process for hydrogen production using thermal and electrical energy derived from nuclear energy or any renewable source like solar energy. In this work, within the context of optimization of the electrolysis process, it is intended to develop a mathematical model that can simulate and assist in parameterization of the electrolysis performed by polymer membrane electrolytic cell. The experimental process to produce hydrogen via the cell membrane, aims to optimize the amount of gas produced using renewable energy with noncarbogenic causing no harm by producing gases deleterious to the environment. (author)

  8. Locally-smeared operator product expansions

    Energy Technology Data Exchange (ETDEWEB)

    Monahan, Christopher; Orginos, Kostantinos

    2014-12-01

    We propose a "locally-smeared Operator Product Expansion" (sOPE) to decompose non-local operators in terms of a basis of locally-smeared operators. The sOPE formally connects nonperturbative matrix elements of smeared degrees of freedom, determined numerically using the gradient flow, to non-local operators in the continuum. The nonperturbative matrix elements do not suffer from power-divergent mixing on the lattice, provided the smearing scale is kept fixed in the continuum limit. The presence of this smearing scale prevents a simple connection to the standard operator product expansion and therefore requires the construction of a two-scale formalism. We demonstrate the feasibility of our approach using the example of real scalar field theory.

  9. Visbreaking based integrated process for bitumen upgrading and hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Sosa, C.; Gonzalez, M.F.; Carbognani, L.; Perez-Zurita, M.J.; Lopez-Linares, F.; Husein, M.; Moore, G.; Pereira, P. [Calgary Univ., AB (Canada). Alberta In Situ Centre For In Situ Energy, Schulich School Of Engineering

    2006-07-01

    New and cost effective upgrading schemes for distillates production and residue disposal are needed in order to recover Alberta's vast heavy oil and bitumen reserves. On average, heavy oils and bitumen contain 50 per cent (w/w) of components remaining after vacuum distillation. A new alternative for upgrading vacuum resids was proposed. The method involves the following 3 processing steps: production of modified, nearly unstable heavy molecules by mild thermal cracking known as visbreaking; adsorption of modified heavy molecules over inexpensive, tailor-designed porous sorbents or catalysts; and, production of hydrogen by low temperature catalytic steam gasification of the adsorbed molecules. This cost effective way of producing hydrogen is based on the selective segregation of a minimal fraction of the heaviest hydrocarbon molecules, those most instable, followed by their gasification at low temperature. This paper presented results on the combined processing as well as using both a model molecule and real feedstock from the Athabasca vacuum resids for the adsorption and hydrogen production steps. The study showed that this new process can obtain high rates of hydrogen production when a kaolin based solid formulation is used as both, adsorbent and catalysts, for these heavy molecules. It was concluded that this alternative method for producing hydrogen at upgrading sites in northern Alberta has potential for both installed and future up-graders to improve the quality of synthetic crude being produced. The hydrogen produced from the gasification of these heavy compounds could be used for both refining purposes or for in-situ reservoir upgrading. 27 refs., 3 figs.

  10. Photosynthetic Hydrogen and Oxygen Production by Green Algae

    Energy Technology Data Exchange (ETDEWEB)

    Greenbaum, E.; Lee, J.W.

    1999-08-22

    Photosynthesis research at Oak Ridge National Laboratory is focused on hydrogen and oxygen production by green algae in the context of its potential as a renewable fuel and chemical feed stock. Beginning with its discovery by Gaffron and Rubin in 1942, motivated by curiosity-driven laboratory research, studies were initiated in the early 1970s that focused on photosynthetic hydrogen production from an applied perspective. From a scientific and technical point of view, current research is focused on optimizing net thermodynamic conversion efficiencies represented by the Gibbs Free Energy of molecular hydrogen. The key research questions of maximizing hydrogen and oxygen production by light-activated water splitting in green algae are: (1) removing the oxygen sensitivity of algal hydrogenases; (2) linearizing the light saturation curves of hotosynthesis throughout the entire range of terrestrial solar irradiance-including the role of bicarbonate and carbon dioxide in optimization of photosynthetic electron transpor;t and (3) constructing real-world bioreactors, including the generation of hydrogen and oxygen against workable back pressures of the photoproduced gases.

  11. DOE Hydrogen, Fuel Cells and Infrastructure Technologies Program Integrated Hydrogen Production, Purification and Compression System

    Energy Technology Data Exchange (ETDEWEB)

    Tamhankar, Satish; Gulamhusein, Ali; Boyd, Tony; DaCosta, David; Golben, Mark

    2011-06-30

    The project was started in April 2005 with the objective to meet the DOE target of delivered hydrogen of <$1.50/gge, which was later revised by DOE to $2-$3/gge range for hydrogen to be competitive with gasoline as a fuel for vehicles. For small, on-site hydrogen plants being evaluated at the time for refueling stations (the 'forecourt'), it was determined that capital cost is the main contributor to the high cost of delivered hydrogen. The concept of this project was to reduce the cost by combining unit operations for the entire generation, purification, and compression system (refer to Figure 1). To accomplish this, the Fluid Bed Membrane Reactor (FBMR) developed by MRT was used. The FBMR has hydrogen selective, palladium-alloy membrane modules immersed in the reformer vessel, thereby directly producing high purity hydrogen in a single step. The continuous removal of pure hydrogen from the reformer pushes the equilibrium 'forward', thereby maximizing the productivity with an associated reduction in the cost of product hydrogen. Additional gains were envisaged by the integration of the novel Metal Hydride Hydrogen Compressor (MHC) developed by Ergenics, which compresses hydrogen from 0.5 bar (7 psia) to 350 bar (5,076 psia) or higher in a single unit using thermal energy. Excess energy from the reformer provides up to 25% of the power used for driving the hydride compressor so that system integration improved efficiency. Hydrogen from the membrane reformer is of very high, fuel cell vehicle (FCV) quality (purity over 99.99%), eliminating the need for a separate purification step. The hydride compressor maintains hydrogen purity because it does not have dynamic seals or lubricating oil. The project team set out to integrate the membrane reformer developed by MRT and the hydride compression system developed by Ergenics in a single package. This was expected to result in lower cost and higher efficiency compared to conventional hydrogen production

  12. Local glucocorticoid production in the thymus.

    Science.gov (United States)

    Talaber, Gergely; Jondal, Mikael; Okret, Sam

    2015-11-01

    Besides generating immunocompetent T lymphocytes, the thymus is an established site of de novo extra-adrenal glucocorticoid (GC) production. Among the compartments of the thymus, both stromal thymic epithelial cells (TECs) and thymocytes secrete biologically active GCs. Locally produced GCs secreted by the various thymic cellular compartments have been suggested to have different impact on thymic homeostasis. TEC-derived GCs may regulate thymocyte differentiation whereas thymocyte-derived GCs might regulate age-dependent involution. However the full biological significance of thymic-derived GCs is still not fully understood. In this review, we summarize and describe recent advances in the understanding of local GC production in the thymus and immunoregulatory steroid production by peripheral T cells and highlight the possible role of local GCs for thymus function.

  13. Designer proton-channel transgenic algae for photobiological hydrogen production

    Science.gov (United States)

    Lee, James Weifu [Knoxville, TN

    2011-04-26

    A designer proton-channel transgenic alga for photobiological hydrogen production that is specifically designed for production of molecular hydrogen (H.sub.2) through photosynthetic water splitting. The designer transgenic alga includes proton-conductive channels that are expressed to produce such uncoupler proteins in an amount sufficient to increase the algal H.sub.2 productivity. In one embodiment the designer proton-channel transgene is a nucleic acid construct (300) including a PCR forward primer (302), an externally inducible promoter (304), a transit targeting sequence (306), a designer proton-channel encoding sequence (308), a transcription and translation terminator (310), and a PCR reverse primer (312). In various embodiments, the designer proton-channel transgenic algae are used with a gas-separation system (500) and a gas-products-separation and utilization system (600) for photobiological H.sub.2 production.

  14. CERAMIC MEMBRANES FOR HYDROGEN PRODUCTION FROM COAL

    Energy Technology Data Exchange (ETDEWEB)

    George R. Gavalas

    2004-04-01

    The preparation and performance of membranes for application to hydrogen separation from coal-derived gas is described. The membrane material investigated was dense amorphous silica deposited on a suitable support by chemical vapor deposition (CVD). Two types of support materials were pursued. One type consisted of a two-layer composite, zeolite silicalite/{alpha}-Al{sub 2}O{sub 3}, in the form of tubes approximately 0.7 cm in diameter. The other type was porous glass tubes of diameter below 0.2 cm. The first type of support was prepared starting from {alpha}-Al{sub 2}O{sub 3} tubes of 1{micro}m mean pore diameter and growing by hydrothermal reaction a zeolite silicalite layer inside the pores of the alumina at the OD side. After calcination to remove the organic template used in the hydrothermal reaction, CVD was carried out to deposit the final silica layer. CVD was carried out by alternating exposure of the surface with silicon tetrachloride and water vapor. SEM and N2 adsorption measurements were employed to characterize the membranes at several stages during their preparation. Permeation measurements of several gases yielded H{sub 2}:N{sub 2} ideal selectivity of 150-200 at room temperature declining to 110 at 250 C. The second type of support pursued was porous glass tubes prepared by a novel extrusion technique. A thick suspension of borosilicate glass powder in a polyethersulfone solution was extruded through a spinneret and after gelation the glass-polymer tube was heat treated to obtain a gas-tight glass tube. Leaching of the glass tube in hot water yielded connected pores with diameter on the order of 100 nm. CVD of the final silica layer was not carried out on these tubes on account of their large pore size.

  15. Hydrogen production from agricultural waste by dark fermentation: A review

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Xin Mei; Trably, Eric; Latrille, Eric; Carrere, Helene; Steyer, Jean-Philippe [INRA, UR050, Laboratoire de Biotechnologie de l' Environnement, F-11100 Narbonne (France)

    2010-10-15

    The degradation of the natural environment and the energy crisis are two vital issues for sustainable development worldwide. Hydrogen is considered as one of the most promising candidates as a substitute for fossil fuels. In this context, biological processes are considered as the most environmentally friendly alternatives for satisfying future hydrogen demands. In particular, biohydrogen production from agricultural waste is very advantageous since agri-wastes are abundant, cheap, renewable and highly biodegradable. Considering that such wastes are complex substrates and can be degraded biologically by complex microbial ecosystems, the present paper focuses on dark fermentation as a key technology for producing hydrogen from crop residues, livestock waste and food waste. In this review, recent findings on biohydrogen production from agricultural wastes by dark fermentation are reported. Key operational parameters such as pH, partial pressure, temperature and microbial actors are discussed to facilitate further research in this domain. (author)

  16. Catalytic carbon membranes for hydrogen production. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Damle, A.S.; Gangwal, S.K.

    1992-01-01

    Commercial carbon composite microfiltration membranes may be modified for gas separation applications by providing a gas separation layer with pores in the 1- to 10-nm range. Several organic polymeric precursors and techniques for depositing a suitable layer were investigated in this project. The in situ polymerization technique was found to be the most promising, and pure component permeation tests with membrane samples prepared with this technique indicated Knudsen diffusion behavior. The gas separation factors obtained by mixed-gas permeation tests were found to depend strongly on gas temperature and pressure indicating significant viscous flow at high-pressure conditions. The modified membranes were used to carry out simultaneous water gas shift reaction and product hydrogen separation. These tests indicated increasing CO conversions with increasing hydrogen separation. A simple process model was developed to simulate a catalytic membrane reactor. A number of simulations were carried out to identify operating conditions leading to product hydrogen concentrations over 90 percent. (VC)

  17. Hydrogen production via catalytic processing of renewable feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Nazim Muradov; Franklyn Smith; Ali T-Raissi [Florida Solar Energy Center, University of Central Florida, Cocoa, Florida, (United States)

    2006-07-01

    Landfill gas (LFG) and biogas can potentially become important feedstocks for renewable hydrogen production. The objectives of this work were: (1) to develop a catalytic process for direct reforming of CH{sub 4}-CO{sub 2} gaseous mixture mimicking LFG, (2) perform thermodynamic analysis of the reforming process using AspenPlus chemical process simulator, (3) determine operational conditions for auto-thermal (or thermo-neutral) reforming of a model CH{sub 4}-CO{sub 2} feedstock, and (4) fabricate and test a bench-scale hydrogen production unit. Experimental data obtained from catalytic reformation of the CH{sub 4}-CO{sub 2} and CH{sub 4}-CO{sub 2}-O{sub 2} gaseous mixtures using Ni-catalyst were in a good agreement with the simulation results. It was demonstrated that catalytic reforming of LFG-mimicking gas produced hydrogen with the purity of 99.9 vol.%. (authors)

  18. Experimental study of hydrogen production by direct decomposition of water

    Science.gov (United States)

    Bilgen, E.; Galindo, J.; Baykara, S. Z.

    The hydrogen production by direct decomposition of water in a solar furnace is studied. The set-up is a horizontal axis system consisting of two 1.0 kW parabolic concentrators, both powered by a single heliostat. A temperature of 3000 K is possible. The water is fed to the reactor installed at the focal space of the concentrator, and the steam is decomposed at about 2500 K. The reactor consisted of a cylindrical cavity type refractory receiver covered with a silica cupola. The steam was introduced at a known rate into the cavity and the product gases were quenched. After the condensation of steam, hydrogen and oxygen were collected in a reservoir. Results indicate that with an optimized system, it is possible to produce hydrogen at about 70 percent rate of the theoretical value at the temperature level studied.

  19. A Study of a nuclear hydrogen production demonstration plant

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Jong Hwa and others [KAERI, Daejeon (Korea, Republic of); Bae, Ki Kwang [Korea Institute of Energy Research, Daejeon (Korea, Republic of); Jung, Kwang Deog [Korea Institute od Science and Technology, Seoul (Korea, Republic of)

    2007-03-15

    The current energy supply system is burdened environmental and supply problems. The concept of a hydrogen economy has been actively discussed worldwide. KAERI has set up a plan to demonstrate massive production of hydrogen using a VHTR by the early 2020s. The technological gap to meet this goal was identified during the past few years. The hydrogen production process, a process heat exchanger, the efficiency of an I/S thermochemical cycle, the manufacturing of components, the analysis tools of VHTR, and a coated particle fuel are key areas that require urgent development. Candidate NHDD plant designs based on a 200 MWth VHTR core and I/S thermochemical process have been studied and some of analysis results are presented in this paper.

  20. Nuclear driven water decomposition plant for hydrogen production

    Science.gov (United States)

    Parker, G. H.; Brecher, L. E.; Farbman, G. H.

    1976-01-01

    The conceptual design of a hydrogen production plant using a very-high-temperature nuclear reactor (VHTR) to energize a hybrid electrolytic-thermochemical system for water decomposition has been prepared. A graphite-moderated helium-cooled VHTR is used to produce 1850 F gas for electric power generation and 1600 F process heat for the water-decomposition process which uses sulfur compounds and promises performance superior to normal water electrolysis or other published thermochemical processes. The combined cycle operates at an overall thermal efficiency in excess of 45%, and the overall economics of hydrogen production by this plant have been evaluated predicated on a consistent set of economic ground rules. The conceptual design and evaluation efforts have indicated that development of this type of nuclear-driven water-decomposition plant will permit large-scale economic generation of hydrogen in the 1990s.

  1. Methane and hydrogen production from crop biomass through anaerobic digestion

    Energy Technology Data Exchange (ETDEWEB)

    Pakarinen, O.

    2011-07-01

    The feasibility of methane and hydrogen production from energy crops through anaerobic digestion was evaluated in this thesis. The effects of environmental conditions, e.g. pH and temperature, as well as inoculum source on H{sub 2} yield were studied in batch assays. In addition, the effects of pre-treatments on methane and hydrogen yield as well as the feasibility of two-stage H{sub 2} + CH{sub 4} production was evaluated. Moreover, the effect of storage on methane yield of grasses was evaluated. Monodigestion of grass silage for methane production was studied, as well as shifting the methanogenic process to hydrogenic. Hydrogen production from grass silage and maize was shown to be possible with heat-treated inoculum in batch assays, with highest H{sub 2} yields of 16.0 and 9.9 ml gVS{sub added}-1 from untreated grass silage and maize, respectively. Pre-treatments (NaOH, HCl and water-extraction) showed some potential in increasing H{sub 2} yields, while methane yields were not affected. Two-stage H{sub 2} + CH{sub 4} producing process was shown to improve CH{sub 4} yields when compared to traditional one-stage CH{sub 4} process. Methane yield from grass silage monodigestion in continuously stirred tank reactor (CSTR) with organic loading rate (OLR) of 2 kgVS (m3d)-1 and hydraulic retention time (HRT) of 30 days was at most 218 l kgVS{sub fed}-1. Methanogenic process was shifted to hydrogenic by increasing the OLR to 10 kgVS (m3d)-1 and shortening the HRT to 6 days. Highest H{sub 2} yield from grass silage was 42 l kgVS{sub fed}-1 with a maximum H{sub 2} content of 24 %. Energy crops can be successfully stored even for prolonged periods without decrease in methane yield. However, under sub-optimal storage conditions loss in volatile solids (VS) content and methane yield can occur. According to present results energy crops such as grass silage and maize can be converted to hydrogen or methane in AD process. Hydrogen energy yields are typically only 2-5 % of the

  2. Sorption enhanced reaction process (SERP) for production of hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Sircar, S.; Anand, M.; Carvill, B. [Air Products and Chemicals, Inc., Allentown, PA (United States)] [and others

    1995-09-01

    Sorption Enhanced Reaction (SER) is a novel process that is being developed for the production of lower cost hydrogen by steam-methane reforming (SMR). In this process, the reaction of methane with steam is carried out in the presence of an admixture of a catalyst and a selective adsorbent for carbon dioxide. The consequences of SER are: (1) reformation reaction at a significantly lower temperature (300-500{degrees}C) than conventional SMR (800-1100{degrees}C), while achieving the same conversion of methane to hydrogen, (2) the product hydrogen is obtained at reactor pressure (200-400 psig) and at 99+% purity directly from the reactor (compared to only 70-75% H{sub 2} from conventional SMR reactor), (3) downstream hydrogen purification step is either eliminated or significantly reduced in size. The early focus of the program will be on the identification of an adsorbent/chemisorbent for CO{sub 2} and on the demonstration of the SER concept for SMR in our state-of-the-art bench scale process. In the latter stages, a pilot plant will be built to scale-up the technology and to develop engineering data. The program has just been initiated and no significant results for SMR will be reported. However, results demonstrating the basic principles and process schemes of SER technology will be presented for reverse water gas shift reaction as the model reaction. If successful, this technology will be commercialized by Air Products and Chemicals, Inc. (APCI) and used in its existing hydrogen business. APCI is the world leader in merchant hydrogen production for a wide range of industrial applications.

  3. LOCAL PRODUCTS IMAGE DETERMINANT COMMUNES OF NISKO

    Directory of Open Access Journals (Sweden)

    Marta Kawa

    2012-01-01

    Full Text Available The article is a characterization of local products, creating an image of Krzeszów, Rudnik and Ulanów municipalities of the Nisko county, in the Podkarpackie province. The study of 500 inhabitants showed that knowledge of these products is varied. The best known were: plum jam from Krzeszów, wickerwork from Rudnik, and rafting bread and rafting tradition cultivated by inhabitants of Ulanów.

  4. Hydrogen production from water hyacinth through dark- and photo- fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Su, Huibo; Cheng, Jun; Zhou, Junhu; Song, Wenlu; Cen, Kefa [State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou 310027 (China)

    2010-09-15

    This article discusses the method of producing hydrogen from water hyacinth. Water hyacinth was pretreated with microwave heating and alkali to enhance the enzymatic hydrolysis and hydrogen production in a two-step process of dark- and photo- fermentation. Water hyacinth with various concentrations of 10-40 g/l was pretreated with four methods: (1) steam heating; (2) steam heating and microwave heating/alkali pretreatment; (3) steam heating and enzymatic hydrolysis; (4) steam heating, microwave heating/alkali pretreatment and enzymatic hydrolysis. Water hyacinth (20 g/l) pretreated with method 4 gave the maximum reducing sugar yield of 30.57 g/100 g TVS, which was 45.6% of the theoretical reducing sugar yield (67.0 g/100 g TVS). The pretreated water hyacinth was used to produce hydrogen by mixed H{sub 2}-producing bacteria in dark fermentation. The maximum hydrogen yield of 76.7 ml H{sub 2}/g TVS was obtained at 20 g/l of water hyacinth. The residual solutions from dark fermentation (mainly acetate and butyrate) were used to further produce hydrogen by immobilized Rhodopseudomonas palustris in photo fermentation. The maximum hydrogen yield of 522.6 ml H{sub 2}/g TVS was obtained at 10 g/l of water hyacinth. Through a combined process of dark- and photo- fermentation, the maximum hydrogen yield from water hyacinth was dramatically enhanced from 76.7 to 596.1 ml H{sub 2}/g TVS, which was 59.6% of the theoretical hydrogen yield. (author)

  5. Bio-hydrogen production from renewable organic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Shihwu Sung

    2004-04-30

    Methane fermentation has been in practice over a century for the stabilization of high strength organic waste/wastewater. Although methanogenesis is a well established process and methane--the end-product of methanogenesis is a useful energy source; it is a low value end product with relatively less energy content (about 56 kJ energy/g CH{sub 4}). Besides, methane and its combustion by-product are powerful greenhouse gases, and responsible for global climate change. So there is a pressing need to explore alternative environmental technologies that not only stabilize the waste/wastewater but also generate benign high value end products. From this perspective, anaerobic bioconversion of organic wastes to hydrogen gas is an attractive option that achieves both goals. From energy security stand point, generation of hydrogen energy from renewable organic waste/wastewater could substitute non-renewable fossil fuels, over two-third of which is imported from politically unstable countries. Thus, biological hydrogen production from renewable organic waste through dark fermentation represents a critically important area of bioenergy production. This study evaluated both process engineering and microbial physiology of biohydrogen production.

  6. Fermentative hydrogen production from pretreated biomass: A comparative study

    NARCIS (Netherlands)

    Panagiotopoulos, I.A.; Bakker, R.R.; Budde, M.A.W.; Vrije, de G.J.; Claassen, P.A.M.; Koukios, E.G.

    2009-01-01

    The aim of this work was to evaluate the potential of employing biomass resources from different origin as feedstocks for fermentative hydrogen production. Mild-acid pretreated and hydrolysed barley straw (BS) and corn stalk (CS), hydrolysed barley grains (BG) and corn grains (CG), and sugar beet ex

  7. Non-thermal production of pure hydrogen from biomass : HYVOLUTION

    NARCIS (Netherlands)

    Claassen, P.A.M.; Vrije, de G.J.

    2006-01-01

    HYVOLUTION is the acronym of an Integrated Project ¿Non-thermal production of pure hydrogen from biomass¿ which has been granted in the Sixth EU Framework Programme on Research, Technological Development and Demonstration, Priority 6.1.ii, Sustainable Energy Systems. The aim of HYVOLUTION: ¿Developm

  8. Hydrogen production from palm oil mill effluent by fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Tanisho, S.; Shimazaki, T. [Yokohama National Univ., Shigeharu TANISHO and Tsuruyo SHIMAZAKI, Yokohama (Japan)

    2003-09-01

    Hydrogen production by fermentation was examined by using palm oil mill effluent. Clostridium butyricum produced more than 2.2 NL of hydrogen from 1 L of raw POME at pH 5.0, and Enterobacter aerogenes produced ca. 1.9 NL at pH 6.0. While from the culture liquid added 1% of peptone on the raw POME, C. butyricum produced more than 3.3 NL and also E. aerogenes 3.4 NL at pH 6.0 and 5.0, respectively. In this manner, the addition of nitrogen source to the POME liquid exerted an influence on the volume of hydrogen production. Since Aspergillus niger has ability to produce cellulase, co-cultivation of C.butyricum with A. niger was tried to utilize celluloses in the POME. Against our expectations, however, the results were lower productivities than pure cultivation's. We analyzed the components of POME by liquid chromatography and capillary electrophoresis before and after cultivation. The main substrate for hydrogen production was found to be glycerol. (authors)

  9. Non-thermal production of pure hydrogen from biomass : HYVOLUTION

    NARCIS (Netherlands)

    Claassen, P.A.M.; Vrije, de G.J.

    2006-01-01

    HYVOLUTION is the acronym of an Integrated Project ¿Non-thermal production of pure hydrogen from biomass¿ which has been granted in the Sixth EU Framework Programme on Research, Technological Development and Demonstration, Priority 6.1.ii, Sustainable Energy Systems. The aim of HYVOLUTION:

  10. EVALUATING HYDROGEN PRODUCTION IN BIOGAS REFORMING IN A MEMBRANE REACTOR

    National Research Council Canada - National Science Library

    Silva, F. S. A; Benachour, M; Abreu, C. A. M

    2015-01-01

    Abstract Syngas and hydrogen production by methane reforming of a biogas (CH4/CO2 = 2.85) using carbon dioxide was evaluated in a fixed bed reactor with a Pd-Ag membrane in the presence of a nickel catalyst...

  11. A Review on Patents for Hydrogen Production Using Membrane Reactors

    NARCIS (Netherlands)

    Gallucci, Fausto; Basile, Angelo; Iulianelli, Adolfo; Kuipers, J.A.M.

    2009-01-01

    Membrane reactors are a modern configuration which integrates reaction and separation units in one vessel and results in a tremendous degree of process intensification. Application of membrane reactors for hydrogen production has been widely studied in literature because membranes with infinite perm

  12. Non-thermal production of pure hydrogen from biomass: HYVOLUTION

    NARCIS (Netherlands)

    Claassen, P.A.M.; Vrije, de G.J.; Koukios, E.G.; Niel, van E.W.J.; Eroglu, I.; Modigell, M.; Friedl, A.; Wukovits, W.; Ahrer, W.

    2010-01-01

    The objectives and methodology of the EU-funded research project HYVOLUTION devoted to hydrogen production from biomass are reviewed. The main scientific objective of this project is the development of a novel two-stage bioprocess employing thermophilic and phototrophic bacteria, for the cost-effect

  13. Existing large steam power plant upgraded for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Galanti, L.; Franzoni, A.; Traverso, A.; Massardo, A.F. [University of Genoa, Genoa (Italy)

    2011-05-15

    This paper presents and discusses the results of a complete thermoeconomic analysis of an integrated power plant for co-production of electricity and hydrogen via pyrolysis and gasification processes fed by various coals and mixture of coal and biomass, applied to an existing large steam power plant (ENEL Brindisi power plant - 660 MWe). Two different technologies for the syngas production section are considered: pyrolysis process and direct pressurized gasification. Moreover, the proximity of a hydrogen production and purification plants to an existing steam power plant favors the inter-exchange of energy streams, mainly in the form of hot water and steam, which reduces the costs of auxiliary equipment. The high quality of the hydrogen would guarantee its usability for distributed generation and for public transport. The results were obtained using WTEMP thermoeconomic software, developed by the Thermochemical Power Group of the University of Genoa, and this project has been carried out within the framework of the FISR National project 'Integrated systems for hydrogen production and utilization in distributed power generation'.

  14. Photobiological production of hydrogen: a solar energy conversion option

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, P.; Lien, S.; Seibert, M.

    1979-01-01

    This literature survey of photobiological hydrogen production covers the period from its discovery in relatively pure cultures during the early 1930s to the present. The focus is hydrogen production by phototrophic organisms (and their components) which occurs at the expense of light energy and electron-donating substrates. The survey covers the major contributions in the area; however, in many cases, space has limited the degree of detail provided. Among the topics included is a brief historical overview of hydrogen metabolism in photosynthetic bacteria, eucaryotic algae, and cyanobacteria (blue--green algae). The primary enzyme systems, including hydrogenase and nitrogenase, are discussed along with the manner in which they are coupled to electron transport and the primary photochemistry of photosynthesis. A number of in vivo and in vitro photobiological hydrogen evolving schemes including photosynthetic bacterial, green algal, cyanobacterial, two-stage, and cell-free systems are examined in some detail. The remainder of the review discusses specific technical problem areas that currently limit the yield and duration of many of the systems and research that might lead to progress in these specific areas. The final section outlines, in broadest terms, future research directions necessary to develop practical photobiological hydrogen-producing systems. Both whole cell (near- to mid-term) and cell-free (long-term) systems should be emphasized. Photosynthetic bacteria currently show the most promise for near-term applied systems.

  15. Process development for hydrogen production with Chlamydomonas reinhardtii based on growth and product formation kinetics.

    Science.gov (United States)

    Lehr, Florian; Morweiser, Michael; Rosello Sastre, Rosa; Kruse, Olaf; Posten, Clemens

    2012-11-30

    Certain strains of microalgae are long known to produce hydrogen under anaerobic conditions. In Chlamydomonas reinhardtii the oxygen-sensitive hydrogenase enzyme recombines electrons from the chloroplast electron transport chain with protons to form molecular hydrogen directly inside the chloroplast. A sustained hydrogen production can be obtained under low sulfur conditions in C. reinhardtii, reducing the net oxygen evolution by reducing the photosystem II activity and thereby overcoming the inhibition of the hydrogenases. The development of specially adapted hydrogen production strains led to higher yields and optimized biological process preconditions. So far sustainable hydrogen production required a complete exchange of the growth medium to establish sulfur-deprived conditions after biomass growth. In this work we demonstrate the transition from the biomass growth phase to the hydrogen production phase in a single batch culture only by exact dosage of sulfur. This eliminates the elaborate and energy intensive solid-liquid separation step and establishes a process strategy to proceed further versus large scale production. This strategy has been applied to determine light dependent biomass growth and hydrogen production kinetics to assess the potential of H₂ production with C. reinhardtii as a basis for scale up and further process optimization.

  16. Biohydrogen production from CO-rich syngas via a locally isolated Rhodopseudomonas palustris PT.

    Science.gov (United States)

    Pakpour, Fatemeh; Najafpour, Ghasem; Tabatabaei, Meisam; Tohidfar, Masoud; Younesi, Habiboallah

    2014-05-01

    Biohydrogen production through water–gas shift (WGS) reaction by a biocatalyst was conducted in batch fermentation. The isolated photosynthetic bacterium Rhodopseudomonas palustris PT was able to utilize carbon monoxide and simultaneously produce hydrogen. Light exposure was provided as an indispensable requirement for the first stage of bacterial growth, but throughout the hydrogen production stage, the energy requirement was met through the WGS reaction. At ambient pressure and temperature, the effect of various sodium acetate concentrations in presence of CO-rich syngas on cell growth, carbon monoxide consumption, and biohydrogen production was also investigated. Maximal efficiency of hydrogen production in response to carbon monoxide consumption was recorded at 86 % and the highest concentration of hydrogen at 33.5 mmol/l was achieved with sodium acetate concentration of 1.5 g/l. The obtained results proved that the local isolate; R. palustris PT, was able to utilize CO-rich syngas and generate biohydrogen via WGS reaction.

  17. Extremophile mediated hydrogen production for hydrogenation of substrates in aqueous media

    Science.gov (United States)

    Anjom, Mouzhgun

    Catalytic hydrogenation reactions are pervasive throughout our economy, from production of margarine as food, liquid fuels for transportation and chiral drugs such as L-DOPA. H2 production from non-fossil fuel feedstocks is highly desirable for transition to the "Hydrogen Economy". Also, the rates of hydrogenation reactions that involve a substrate, H 2 gas and a catalyst are often limited by the solubility of H2 in solvent. The present research thus envisioned designing water-soluble catalysts that could effectively utilize biologically produced H2 in a coupled system to hydrogenate substrates in homogeneous mode (two-phase system). Biological production of H2 as an end product or byproduct of the metabolism of organisms that operate under strict anaerobic conditions has been proposed. However, contrary to what was previously observed, Thermotoga neapolitana, belonging to the order of Thermotogales efficiently produces H2 gas under microaerobic conditions (Van Ooteghem et al. 2004). For H2 production by T. neapolitana in the bacterial growth medium (DSM 5068) at an optimum temperature of 70 C, our results in batch mode show that: (1) H2 was produced from glucose though with 16% efficiency, the rest goes to biomass production, (2) H2 gas was produced even when the cultures were inoculated under microaerobic conditions (up to 8% (v/v) O2) suggesting a protective mechanism for one or more [Fe-Fe] hydrogenases in T. neapolitana, (3) H2 production was pH dependent but addition of simple, non-toxic physiological buffering additives such as Methylene succinic acid increased H2 production and (4) H2 production rate varied linearly in the 100--6800 kPa pressure range. We then screened various water-soluble metal catalysts in batch mode and selected the RhCl3.3H2O/TPPTS (TPPTS is a water-soluble ligand) system that achieved 86% hydrogenation of Methylene succinic acid (an olefin) in an aqueous medium pressurized with preformed H2. When water was replaced with the DSM 5068

  18. Hydrogen production by Rhodopseudomonas palustris WP 3-5 in a serial photobioreactor fed with hydrogen fermentation effluent.

    Science.gov (United States)

    Lee, Chi-Mei; Hung, Guo-Jan; Yang, Chu-Fang

    2011-09-01

    In this study, a lab-scale serial photobioreactor composed of three column reactors was constructed and continuously operated to investigate several parameters influencing photohydrogen production when using the synthetic wastewater and the anaerobic hydrogen fermentation effluents as the influents. The results indicated that better hydrogen production rate was obtained when the serial photobioreactor was operated under cellular recycling at a short HRT of 8h. The serial photobioreactor maintained high hydrogen content ca. 80% in the produced gas and 0.4× dilution ratio was the suitable ratio for hydrogen production. When the photobioreactor fed with the real wastewater (Effluent 1) containing 100 mg/L NH4Cl, Column 1 reactor successfully reduced ammonia concentration to about 60 mg/L for cell synthesis, resulting in a steady hydrogen production in the following two column reactors. The average hydrogen production rate was 205 mL-H2/L/d.

  19. Electrolytic hydrogen fuel production with solid polymer electrolyte technology.

    Science.gov (United States)

    Titterington, W. A.; Fickett, A. P.

    1973-01-01

    A water electrolysis technology based on a solid polymer electrolyte (SPE) concept is presented for applicability to large-scale hydrogen production in a future energy system. High cell current density operation is selected for the application, and supporting cell test performance data are presented. Demonstrated cell life data are included to support the adaptability of the SPE system to large-size hydrogen generation utility plants as needed for bulk energy storage or transmission. The inherent system advantages of the acid SPE electrolysis technology are explained. System performance predictions are made through the year 2000, along with plant capital and operating cost projections.

  20. Methane and hydrogen production by human intestinal anaerobic bacteria.

    Science.gov (United States)

    McKay, L F; Holbrook, W P; Eastwood, M A

    1982-06-01

    The gas above liquid cultures of a variety of human intestinal anaerobic bacteria was sampled and analysed by headspace gas chromatography. Hydrogen production was greatest with strains of the genus Clostridium, intermediate with anaerobic cocci and least with Bacteroides sp. Very few strains produced methane although small amounts were detected with one strain of B. thetaiotaomicron, C. perfringens and C. histolyticum. There may be a relationship between these anaerobic bacteria and several gastrointestinal disorders in which there is a build up of hydrogen or methane in the intestines.

  1. Photochemical production of hydrogen with zinc sulfide suspensions

    Energy Technology Data Exchange (ETDEWEB)

    Reber, J.F.; Meier, K.

    1984-11-22

    Hydrogen has been produced efficiently by the irradiation of suspensions of metalized ZnS powders in the presence of hole scavengers such as S/sup 2 -/ and SO/sub 3//sup 2 -/ions, mixtures of these two, or S/sup 2 -/ and hypophosphite ions. Results of investigation of the properties of active ZnS photocatalysts, the reaction parameters, and the formation of the reaction products are reported. The rate of the reaction was found to be strongly dependent on the amount of ZnS, and ZnS produced 5 times as much hydrogen as CdS.

  2. Hydrogen production from methane reforming: thermodynamic assessment

    Energy Technology Data Exchange (ETDEWEB)

    Assis, A.J.; Hori, Carla E.; Avila Neto, Cicero; Franco, Tatiana [Federal University of Uberlandia (UFU), MG (Brazil). School of Chemical Engineering]. E-mail: adilsonjassis@gmail.com

    2008-07-01

    The main contributions of this study are to conduct a comparative thermodynamic analysis of methane reforming reactions and to asses the influence of key operational variables on chemical equilibrium using an in-house code, developed in the open-source software Scilab{sup c} INRIA-ENPC (www.scilab.org). Equilibrium compositions are calculated by two distinct methods: evaluation of equilibrium constants and Lagrange multipliers. Both methods result in systems of non-linear algebraic equations, solved numerically using the Scilab function 'fsolve'. Comparison between experimental and simulated equilibrium data, published in the literature, was used to validate the simulated results. Effects of temperature, pressure, initial H{sub 2}O/CH{sub 4} ratio (steam reforming), initial CH{sub 4}:CO{sub 2}:N{sub 2} ratio (dry reforming) and initial O{sub 2}/CH{sub 4} ratio (partial oxidation) on the reaction products were evaluated. (author)

  3. Production of Excited Atomic Hydrogen from Methane

    Science.gov (United States)

    Machacek, J. R.; Andrianarijaona, V. M.; Furst, J. E.; Gay, T. J.; Kilcoyne, A. L. D.; Landers, A. L.; McLaughlin, K. W.

    2009-05-01

    We have measured the production of Lyα and Hα fluorescence from atomic H for the photodissociation of CH4 by linearly-polarized photons with energies between 20 and 65 eV. Comparison between our Lyα relative cross section and that previously reported [1] show different peak height ratios. This also occurs in the Hα cross section when compared to previous data [2]. We do not observe as significant a drop in either cross section above 35 eV. Our measurements were taken with pressures two orders of magnitude lower than those used in ref. [1]. We present comparisons between data sets and a discussion of possible systematic effects. [1] H. Fukuzawa et al., J. Phys. B. 38, 565 (2005). [2] M. Kato et al., J. Phys. B. 35, 4383 (2002). Support provided by the NSF (Grant PHY-0653379), DOE (LBNL/ALS) and ANSTO (Access to Major Research Facilities Programme).

  4. The effect of hydrogen on the parameters of plastic deformation localization in low carbon steel

    Energy Technology Data Exchange (ETDEWEB)

    Lunev, Aleksey G., E-mail: agl@ispms.tsc.ru, E-mail: nadjozhkin@ispms.tsc.ru; Nadezhkin, Mikhail V., E-mail: agl@ispms.tsc.ru, E-mail: nadjozhkin@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055, Russia and National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation); Shlyakhova, Galina V., E-mail: shgv@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055, Russia and Seversk State Technological Institute (National Research Nuclear University MEPhI), Seversk, 636036 (Russian Federation); Barannikova, Svetlana A., E-mail: bsa@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk State University, Tomsk, 634050 (Russian Federation); Tomsk State University of Architecture and Building, Tomsk, 634003 (Russian Federation); Zuev, Lev B., E-mail: lbz@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk State University, Tomsk, 634050 (Russian Federation)

    2014-11-14

    In the present study, the effect of interstitial hydrogen atoms on the mechanical properties and plastic strain localization patterns in tensile tested polycrystals of low-carbon steel Fe-0.07%C has been studied using double exposure speckle photography technique. The main parameters of plastic flow localization at various stages of deformation hardening have been determined in polycrystals of steel electrolytically saturated with hydrogen in a three-electrode electrochemical cell at a controlled constant cathode potential. Also, the effect of hydrogen on changing of microstructure by using optical microscopy has been demonstrated.

  5. New design competences for localized production systems

    DEFF Research Database (Denmark)

    Eriksen, Kaare Riise; Morelli, Nicola

    2005-01-01

    This paper discusses the current development in production culture, based on local production networks. The role of the designer is put in perspective and outlined through a research project, Den Grønne Møbel (DGM), where different design areas were coordinated in a business concept...... and an organization involving different stakeholders. For several years now, DGM has been producing furniture from local materials, hereby aiming to create a new culture for well designed and environmentally sound furniture with a ‘story’. Although not totally new, this organizational model is particularly innovative...... in fully industrialized countries such as Denmark and represents an interesting alternative to globalized industrial production. Furthermore this case is an interesting opportunity to re-discuss the role and competences of designers in such new models. Tools and methods of the design profession...

  6. Biological hydrogen production by dark fermentation: challenges and prospects towards scaled-up production.

    Science.gov (United States)

    RenNanqi; GuoWanqian; LiuBingfeng; CaoGuangli; DingJie

    2011-06-01

    Among different technologies of hydrogen production, bio-hydrogen production exhibits perhaps the greatest potential to replace fossil fuels. Based on recent research on dark fermentative hydrogen production, this article reviews the following aspects towards scaled-up application of this technology: bioreactor development and parameter optimization, process modeling and simulation, exploitation of cheaper raw materials and combining dark-fermentation with photo-fermentation. Bioreactors are necessary for dark-fermentation hydrogen production, so the design of reactor type and optimization of parameters are essential. Process modeling and simulation can help engineers design and optimize large-scale systems and operations. Use of cheaper raw materials will surely accelerate the pace of scaled-up production of biological hydrogen. And finally, combining dark-fermentation with photo-fermentation holds considerable promise, and has successfully achieved maximum overall hydrogen yield from a single substrate. Future development of bio-hydrogen production will also be discussed. Copyright © 2011 Elsevier Ltd. All rights reserved.

  7. Photocatalytic degradation of organic pollutants with simultaneous production of hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Patsoura, Alexia; Kondarides, Dimitris I.; Verykios, Xenophon E. [Department of Chemical Engineering, University of Patras, GR-26504 Patras (Greece)

    2007-06-30

    The photocatalytic degradation of a number of organic compounds in solution, including alcohols and organic acids, has been investigated under unaerated conditions with the use of Pt/TiO{sub 2} photocatalyst and solar or UV irradiation. It has been found that production of CO{sub 2} is in all cases accompanied by evolution of hydrogen, the production rate of which is significantly enhanced, compared with that obtained in the absence of organic additives in solution. Results are explained by considering that organic compounds act as sacrificial electron donors, which become progressively oxidized toward CO{sub 2} by consuming photogenerated holes and/or oxygen. This results in decreased rates of electron-hole recombination and oxygen-hydrogen back reaction and, concomitantly, in increased H{sub 2}-production rates. The rate of photoinduced hydrogen production depends strongly on the concentration of the sacrificial agent employed and to a lesser extent on solution pH and temperature. When complete mineralization of the sacrificial agent is achieved, photogenerated oxygen can no longer be removed from the photocatalyst surface and the H{sub 2}-production rate drops to steady-state values, comparable to those obtained in the absence of the organic compound in solution. The amounts of carbon dioxide and 'additional' hydrogen produced depend on the nature of the organic additive and are directly proportional to its initial concentration in solution. Quantification of results shows that the overall process may be described as 'photoinduced reforming of organic compounds at room temperature'. It is concluded that mineralization of organic pollutants such as alcohols and organic acids, which are common waste products of biomass processing industries, can be achieved with simultaneous production of H{sub 2} fuel. The process may provide an efficient and cost effective method for cleaning up waste streams. (author)

  8. Microbial control of hydrogen sulfide production

    Energy Technology Data Exchange (ETDEWEB)

    Montgomery, A.D.; Bhupathiraju, V.K.; Wofford, N.; McInerney, M.J. [Univ. of Oklahoma, Tulsa, OK (United States)] [and others

    1995-12-31

    A sulfide-resistant strain of Thiobacillus denitrificans, strain F, prevented the accumulation of sulfide by Desulfovibrio desulfuricans when both organisms were grown in liquid medium. The wild-type strain of T. denitrificans did not prevent the accumulation of sulfide produced by D. desulfuricans. Strain F also prevented the accumulation of sulfide by a mixed population of sulfate-reducing bacteria enriched from an oil field brine. Fermentation balances showed that strain F stoichiometrically oxidized the sulfide produced by D. desulfuricans and the oil field brine enrichment to sulfate. The ability of a strain F to control sulfide production in an experimental system of cores and formation water from the Redfield, Iowa, natural gas storage facility was also investigated. A stable, sulfide-producing biofilm was established in two separate core systems, one of which was inoculated with strain F while the other core system (control) was treated in an identical manner, but was not inoculated with strain F. When formation water with 10 mM acetate and 5 mM nitrate was injected into both core systems, the effluent sulfide concentrations in the control core system ranged from 200 to 460 {mu}M. In the test core system inoculated with strain F, the effluent sulfide concentrations were lower, ranging from 70 to 110 {mu}M. In order to determine whether strain F could control sulfide production under optimal conditions for sulfate-reducing bacteria, the electron donor was changed to lactate and inorganic nutrients (nitrogen and phosphate sources) were added to the formation water. When nutrient-supplemented formation water with 3.1 mM lactate and 10 mM nitrate was used, the effluent sulfide concentrations of the control core system initially increased to about 3,800 {mu}M, and then decreased to about 1,100 {mu}M after 5 weeks. However, in the test core system inoculated with strain F, the effluent sulfide concentrations were much lower, 160 to 330 {mu}M.

  9. Design of a Simple and Cheap Water Electrolyser for the Production of Solar Hydrogen

    Directory of Open Access Journals (Sweden)

    Ram Prasad

    2009-06-01

    Full Text Available Commercially available conventional alkaline electrolyser and advanced polymer membrane electrolysers for water electrolysis are quite expensive. Taking into account this aspect, a very simple and cheap water electrolyser has been designed and fabricated utilising easily available economical materials for small scale production of hydrogen using renewable energy from photovoltaic panel. The construction details of the electrolyser with a schematic drawing of the experimental set-up for PV production of H2 are given. In order to fabricate the compact electrolyser, two coaxial tubular PVC pipes were used. The lower part of the inner pipe has fine perforations for the transport of ions through electrolyte between the electrodes. Two cylindrical electrodes, cathode and anode are kept in inner and outer pipes respectively. The performance of hydrogen production was measured using a photovoltaic panel directly connected to the electrolyser under atmospheric pressure and in 27wt% KOH solution. Flow rates of hydrogen and oxygen were measured using a digital flow meter. High purity fuel cell grade hydrogen (99.98% and oxygen (99.85% have been produced. The experimental results confirm that the present electrolyser has eligible properties for hydrogen production in remote areas. No such electrolyser has been reported prior to this work. Copyright (c 2009 by BCREC. All rights reserved.[Received: 20 May 2009, Revised: 14 August 2009, Accepted: 19 August 2009][How to Cite: R. Prasad. (2009. Design of a Simple and Cheap Water Electrolyser for the Production of Solar Hydrogen. Bulletin of Chemical Reaction Engineering and Catalysis, 4(1: 10-15.  doi:10.9767/bcrec.4.1.7113.10-15][How to Link/ DOI: http://dx.doi.org/10.9767/bcrec.4.1.7113.10-15 || or local: http://ejournal.undip.ac.id/index.php/bcrec/article/view/7113 ] 

  10. Hydrogen Production with Steam Reforming of Dimethyl Ether

    Institute of Scientific and Technical Information of China (English)

    Kaoru TAKEISHI; Akane ARASE

    2005-01-01

    @@ 1Introduction Steam reforming of methanol and gasoline is actively researched and developed as hydrogen supply methods for the fuel cells of vehicles and so on. However, these materials have the problems such as the infrastructure, toxicity, difficulty of the reforming, and so forth. Dimethyl ether (DME) does not contain the poisonous substances, and is expected as a clean fuel of the next generation. DME is able to take the place of light oil and LPG, and its physical properties are similar to those of LPG. There is possibility that DME infrastructures will be settled more rapidly than those of hydrogen and methanol, because LPG infrastructures existing are able to use for DME. Then, we have been studying on steam reforming of DME for the hydrogen production.

  11. Hydrogen production employing Spirulina maxima 2342: A chemical analysis

    Energy Technology Data Exchange (ETDEWEB)

    Juantorena, A.U.; Santoyo, E.; Gamboa, S.A.; Lastres, O.D. [Centro de Investigacion en Energia, UNAM, Temixco 62580, Morelos (Mexico); Sebastian, P.J. [Centro de Investigacion en Energia, UNAM, Temixco 62580, Morelos (Mexico); Cuerpo Academico de Energia, UP Chiapas, Tuxtla Gutierrez, Chiapas (Mexico); Sanchez-Escamilla, D. [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Bustos, A. [Centro de Ciencias Fisicas, UNAM, Ave. Universidad, Cuernavaca, Morelos (Mexico); Eapen, D. [Investigacion y Desarrollo en Agroindustria, UP Chiapas, Tuxtla Gutierrez, Chiapas (Mexico)

    2007-10-15

    The biomass of the cyanobacteria, Spirulina maxima 2342, was autotrophically obtained in a 20 l bioreactor under illumination and air bubbling and analyzed for its photobiological hydrogen production capability. A volume of 250 ml of Spirulina sp. taken from the reactor was used as culture sample for performing the experiments. An illumination-agitation process was employed to induce the hydrogen photoproduction reaction. The hydrogen produced in this process was quantified by gas chromatography technique using Molesieve 5 A(16ft x (1)/(8)in) column and a thermal conductivity detector (with a detector temperature of 110{sup o}C and a column temperature of 60{sup o}C). The culture samples were finally observed in an electron microscope to evaluate the effect of vacuum on the Spirulina sp. cells. (author)

  12. Sequestration of carbon dioxide with hydrogen to useful products

    Energy Technology Data Exchange (ETDEWEB)

    Adams, Michael W. W.; Kelly, Robert M.; Hawkins, Aaron B.; Menon, Angeli Lal; Lipscomb, Gina Lynette Pries; Schut, Gerrit Jan

    2017-03-07

    Provided herein are genetically engineered microbes that include at least a portion of a carbon fixation pathway, and in one embodiment, use molecular hydrogen to drive carbon dioxide fixation. In one embodiment, the genetically engineered microbe is modified to convert acetyl CoA, molecular hydrogen, and carbon dioxide to 3-hydroxypropionate, 4-hydroxybutyrate, acetyl CoA, or the combination thereof at levels greater than a control microbe. Other products may also be produced. Also provided herein are cell free compositions that convert acetyl CoA, molecular hydrogen, and carbon dioxide to 3-hydroxypropionate, 4-hydroxybutyrate, acetyl CoA, or the combination thereof. Also provided herein are methods of using the genetically engineered microbes and the cell free compositions.

  13. Water electrolysis for hydrogen production in Brazilian perspective

    Energy Technology Data Exchange (ETDEWEB)

    Saliba-Silva, Adonis Marcelo; Carvalho, Fatima M.S.; Bergamaschi, Vanderlei Sergio; Linardi, Marcelo [Instituto de Pesquisas Energeticas e Nucleares (CCCH/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Fuel Cell and Hydrogen Center], Email: saliba@ipen.br

    2009-07-01

    Hydrogen is a promising energy carrier, which potentially could replace the fossil fuels used in the transportation and distributed energy sector of Brazilian economy. Fossil fuels are polluting by carbogenic emissions from their combustion, being so co-responsible for present global warming. However, no large scale, cost-effective, environmentally non-carbogenic hydrogen production process is currently available for commercialization. There are feasible possibilities to use electrolysis as one of the main sources of hydrogen, especially thinking on combination with renewable sources of energy, mainly eolic and solar. In this work some perspectives for Brazilian energy context is presented, where electrolysis combined with renewable power source and fuel cell power generation would be a good basis to improve the distributed energy supply for remote areas, where the electricity grid is not present or is deficient. (author)

  14. Dynamic Simulation and Optimization of Nuclear Hydrogen Production Systems

    Energy Technology Data Exchange (ETDEWEB)

    Paul I. Barton; Mujid S. Kaximi; Georgios Bollas; Patricio Ramirez Munoz

    2009-07-31

    This project is part of a research effort to design a hydrogen plant and its interface with a nuclear reactor. This project developed a dynamic modeling, simulation and optimization environment for nuclear hydrogen production systems. A hybrid discrete/continuous model captures both the continuous dynamics of the nuclear plant, the hydrogen plant, and their interface, along with discrete events such as major upsets. This hybrid model makes us of accurate thermodynamic sub-models for the description of phase and reaction equilibria in the thermochemical reactor. Use of the detailed thermodynamic models will allow researchers to examine the process in detail and have confidence in the accurary of the property package they use.

  15. Photoelectrochemical based direct conversion systems for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Kocha, S.; Peterson, M.; Arent, D. [National Renewable Energy Lab., Golden, CO (United States)] [and others

    1996-10-01

    Photon driven, direct conversion systems consist of a light absorber and a water splitting catalyst as a monolithic system; water is split directly upon illumination. This one-step process eliminates the need to generate electricity externally and subsequently feed it to an electrolyzer. These configurations require only the piping necessary for transport of hydrogen to an external storage system or gas pipeline. This work is focused on multiphoton photoelectrochemical devices for production of hydrogen directly using sunlight and water. Two types of multijunction cells, one consisting of a-Si triple junctions and the other GaInP{sub 2}/GaAs homojunctions, were studied for the photoelectrochemical decomposition of water into hydrogen and oxygen from an aqueous electrolyte solution. To catalyze the water decomposition process, the illuminated surface of the device was modified either by addition of platinum colloids or by coating with ruthenium dioxide. These colloids have been characterized by gel electrophoresis.

  16. Carbon dioxide free production of hydrogen

    Science.gov (United States)

    Stoppel, L.; Fehling, T.; Geißler, T.; Baake, E.; Wetzel, T.

    2017-07-01

    The present report summarizes the theoretical modelling and experimental investigation results of the study on the direct thermal methane cracking. This work is a part of the LIMTECH-Project (Liquid Metal Technologies) funded of Helmholtz Alliance and was carried out from 2012 to 2017. The Project-part B5 “CO2-free production of hydrogen” focused on experimental testing and particularly on modelling the novel methane cracking method based on liquid metal technology. The new method uses a bubble column reactor, filled with liquid metal, where both the chemical reaction of methane decomposition and the separation of gas fraction from solid carbon occur. Such reactor system was designed and built in the liquid metal laboratory (KALLA) at KIT. The influences of liquid metal temperature distribution in reactor and feed gas flow rate on methane conversion ratio were investigated experimentally at the temperature range from 930°C to 1175 °C and methane flow rate at the reactor inlet from 50 to 200 mLn/min. In parallel with experimental investigations, a thermochemical model, giving insight in the influence of the above mentioned parameters has been developed at KIT and a CFD model was developed at LUH to get an overview about the bubble dynamics in the reaction system. The influence of different bubble sizes and shapes, multi-inlet coalescence effects as well as the potential of electromagnetic stirring have been investigated.

  17. Hydrogen production via urea electrolysis using a gel electrolyte

    Science.gov (United States)

    King, Rebecca L.; Botte, Gerardine G.

    2011-03-01

    A technology was demonstrated for the production of hydrogen and other valuable products (nitrogen and clean water) through the electrochemical oxidation of urea in alkaline media. In addition, this process remediates toxic nitrates and prevents gaseous ammonia emissions. Improvements to urea electrolysis were made through replacement of aqueous KOH electrolyte with a poly(acrylic acid) gel electrolyte. A small volume of poly(acrylic acid) gel electrolyte was used to accomplish the electrochemical oxidation of urea improving on the previous requirement for large amounts of aqueous potassium hydroxide. The effect of gel composition was investigated by varying polymer content and KOH concentrations within the polymer matrix in order to determine which is the most advantageous for the electrochemical oxidation of urea and production of hydrogen.

  18. Thermocatalytic CO2-Free Production of Hydrogen from Hydrocarbon Fuels

    Energy Technology Data Exchange (ETDEWEB)

    University of Central Florida

    2004-01-30

    The main objective of this project is the development of an economically viable thermocatalytic process for production of hydrogen and carbon from natural gas or other hydrocarbon fuels with minimal environmental impact. The three major technical goals of this project are: (1) to accomplish efficient production of hydrogen and carbon via sustainable catalytic decomposition of methane or other hydrocarbons using inexpensive and durable carbon catalysts, (2) to obviate the concurrent production of CO/CO{sub 2} byproducts and drastically reduce CO{sub 2} emissions from the process, and (3) to produce valuable carbon products in order to reduce the cost of hydrogen production The important feature of the process is that the reaction is catalyzed by carbon particulates produced in the process, so no external catalyst is required (except for the start-up operation). This results in the following advantages: (1) no CO/CO{sub 2} byproducts are generated during hydrocarbon decomposition stage, (2) no expensive catalysts are used in the process, (3) several valuable forms of carbon can be produced in the process depending on the process conditions (e.g., turbostratic carbon, pyrolytic graphite, spherical carbon particles, carbon filaments etc.), and (4) CO{sub 2} emissions could be drastically reduced (compared to conventional processes).

  19. Lichen symbiosis: nature's high yielding machines for induced hydrogen production.

    Science.gov (United States)

    Papazi, Aikaterini; Kastanaki, Elizabeth; Pirintsos, Stergios; Kotzabasis, Kiriakos

    2015-01-01

    Hydrogen is a promising future energy source. Although the ability of green algae to produce hydrogen has long been recognized (since 1939) and several biotechnological applications have been attempted, the greatest obstacle, being the O2-sensitivity of the hydrogenase enzyme, has not yet been overcome. In the present contribution, 75 years after the first report on algal hydrogen production, taking advantage of a natural mechanism of oxygen balance, we demonstrate high hydrogen yields by lichens. Lichens have been selected as the ideal organisms in nature for hydrogen production, since they consist of a mycobiont and a photobiont in symbiosis. It has been hypothesized that the mycobiont's and photobiont's consumption of oxygen (increase of COX and AOX proteins of mitochondrial respiratory pathways and PTOX protein of chrolorespiration) establishes the required anoxic conditions for the activation of the phycobiont's hydrogenase in a closed system. Our results clearly supported the above hypothesis, showing that lichens have the ability to activate appropriate bioenergetic pathways depending on the specific incubation conditions. Under light conditions, they successfully use the PSII-dependent and the PSII-independent pathways (decrease of D1 protein and parallel increase of PSaA protein) to transfer electrons to hydrogenase, while under dark conditions, lichens use the PFOR enzyme and the dark fermentative pathway to supply electrons to hydrogenase. These advantages of lichen symbiosis in combination with their ability to survive in extreme environments (while in a dry state) constitute them as unique and valuable hydrogen producing natural factories and pave the way for future biotechnological applications.

  20. Lichen symbiosis: nature's high yielding machines for induced hydrogen production.

    Directory of Open Access Journals (Sweden)

    Aikaterini Papazi

    Full Text Available Hydrogen is a promising future energy source. Although the ability of green algae to produce hydrogen has long been recognized (since 1939 and several biotechnological applications have been attempted, the greatest obstacle, being the O2-sensitivity of the hydrogenase enzyme, has not yet been overcome. In the present contribution, 75 years after the first report on algal hydrogen production, taking advantage of a natural mechanism of oxygen balance, we demonstrate high hydrogen yields by lichens. Lichens have been selected as the ideal organisms in nature for hydrogen production, since they consist of a mycobiont and a photobiont in symbiosis. It has been hypothesized that the mycobiont's and photobiont's consumption of oxygen (increase of COX and AOX proteins of mitochondrial respiratory pathways and PTOX protein of chrolorespiration establishes the required anoxic conditions for the activation of the phycobiont's hydrogenase in a closed system. Our results clearly supported the above hypothesis, showing that lichens have the ability to activate appropriate bioenergetic pathways depending on the specific incubation conditions. Under light conditions, they successfully use the PSII-dependent and the PSII-independent pathways (decrease of D1 protein and parallel increase of PSaA protein to transfer electrons to hydrogenase, while under dark conditions, lichens use the PFOR enzyme and the dark fermentative pathway to supply electrons to hydrogenase. These advantages of lichen symbiosis in combination with their ability to survive in extreme environments (while in a dry state constitute them as unique and valuable hydrogen producing natural factories and pave the way for future biotechnological applications.

  1. Lichen Symbiosis: Nature's High Yielding Machines for Induced Hydrogen Production

    Science.gov (United States)

    Papazi, Aikaterini; Kastanaki, Elizabeth; Pirintsos, Stergios; Kotzabasis, Kiriakos

    2015-01-01

    Hydrogen is a promising future energy source. Although the ability of green algae to produce hydrogen has long been recognized (since 1939) and several biotechnological applications have been attempted, the greatest obstacle, being the O2-sensitivity of the hydrogenase enzyme, has not yet been overcome. In the present contribution, 75 years after the first report on algal hydrogen production, taking advantage of a natural mechanism of oxygen balance, we demonstrate high hydrogen yields by lichens. Lichens have been selected as the ideal organisms in nature for hydrogen production, since they consist of a mycobiont and a photobiont in symbiosis. It has been hypothesized that the mycobiont’s and photobiont’s consumption of oxygen (increase of COX and AOX proteins of mitochondrial respiratory pathways and PTOX protein of chrolorespiration) establishes the required anoxic conditions for the activation of the phycobiont’s hydrogenase in a closed system. Our results clearly supported the above hypothesis, showing that lichens have the ability to activate appropriate bioenergetic pathways depending on the specific incubation conditions. Under light conditions, they successfully use the PSII-dependent and the PSII-independent pathways (decrease of D1 protein and parallel increase of PSaA protein) to transfer electrons to hydrogenase, while under dark conditions, lichens use the PFOR enzyme and the dark fermentative pathway to supply electrons to hydrogenase. These advantages of lichen symbiosis in combination with their ability to survive in extreme environments (while in a dry state) constitute them as unique and valuable hydrogen producing natural factories and pave the way for future biotechnological applications. PMID:25826211

  2. Multistage Extractive Reaction for Hydrogen Peroxide Production by Anthraquinone Process

    Institute of Scientific and Technical Information of China (English)

    WANG Li; L(U) Shuxiang; WANG Yaquan; MI Zhentao

    2005-01-01

    The extractive reaction process of oxygen-working solution-water three-phase system for the production of hydrogen peroxide by the anthraquinone method was investigated in a sieve plate column of 50 mm in internal diameter. The oxidation reaction of anthrahydroquinone in the working solution with oxygen and the extraction of hydrogen peroxide from the working solution into aqueous phase occurred simultaneously in the countercurrent mode. The agitating effect caused by gaseous phase made the droplets of the dispersed phase become smaller, thus, increasing the liquid-liquid interfacial contact areas and resulting in the improvement of the mass transfer velocity. Results showed that the gas-agitation had a beneficial effect on the extraction of hydrogen peroxide from the working solution into the aqueous phase; the concentration of hydrogen peroxide in the raffinate decreased with the increase of the gaseous superficial velocities; and the concentration of H2O2 in the raffinate increased with the increase of the dispersed phase superficial velocity at the same superficial velocity of the gaseous phase. In the G-L-L extractive reaction process, with the increase of the gaseous superficial velocities, both the conversion of the anthrahydroquinone oxidation and the extraction efficiency of hydrogen peroxide first increased significantly, then increased gradually.

  3. Hydrogen production from the monomeric sugars hydrolyzed from hemicellulose by Enterobacter aerogenes

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Yunli; Wang, Jianji; Liu, Zhen; Ren, Yunlai; Li, Guozhi [School of Chemical Engineering and Pharmaceutics, Henan University of Science and Technology, Luoyang 471039, Henan (China)

    2009-12-15

    Relatively large percentages of xylose with glucose, arabinose, mannose, galactose and rhamnose constitute the hydrolysis products of hemicellulose. In this paper, hydrogen production performance of facultative anaerobe (Enterobacter aerogenes) has been investigated from these different monomeric sugars except glucose. It was shown that the stereoisomers of mannose and galactose were more effective for hydrogen production than those of xylose and arabinose. The substrate of 5 g/l xylose resulted in a relative high level of hydrogen yield (73.8 mmol/l), hydrogen production efficiency (2.2 mol/mol) and a maximum hydrogen production rate (249 ml/l/h). The hydrogen yield, hydrogen production efficiency and the maximum hydrogen production rate reached 104 mmol/l, 2.35 mol/mol and 290 ml/l/h, respectively, on a substrate of 10 g/l galactose. The hydrogen yields and the maximum hydrogen production rates increased with an increase of mannose concentrations and reached 119 mmol/l and 518 ml/l/h on the culture of 25 g/l mannose. However, rhamnose was a relative poor carbon resource for E. aerogenes to produce hydrogen, from which the hydrogen yield and hydrogen production efficiency were about one half of that from the mannose substrate. E. aerogenes was found to be a promising strain for hydrogen production from hydrolysis products of hemicellulose. (author)

  4. Biomass-based hydrogen production: A review and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Kalinci, Yildiz [Department of Technical Programs, Izmir Vocational High School, Dokuz Eylul University, Education Campus Buca, Izmir (Turkey); Hepbasli, Arif [Department of Mechanical Engineering, Faculty of Engineering, Ege University, 35100 Izmir (Turkey); Dincer, Ibrahim [Faculty of Engineering and Applied Science, University of Ontario Institute of Technology, 2000 Simcoe Street North, Oshawa, Ontario (Canada)

    2009-11-15

    In this study, various processes for conversion of biomass into hydrogen gas are comprehensively reviewed in terms of two main groups, namely (i) thermo-chemical processes (pyrolysis, conventional gasification, supercritical water gasification (SCWG)), and (ii) biological conversions (fermentative hydrogen production, photosynthesis, biological water gas shift reactions (BWGS)). Biomass-based hydrogen production systems are discussed in terms of their energetic and exergetic aspects. Literature studies and potential methods are then summarized for comparison purposes. In addition, a biomass gasification process via oxygen and steam in a downdraft gasifier is exergetically studied for performance assessment as a case study. The operating conditions and strategies are really important for better performance of the system for hydrogen production. A distinct range of temperatures and pressures is used, such as that the temperatures may vary from 480 to 1400 C, while the pressures are in the range of 0.1-50 MPa in various thermo-chemical processes reviewed. For the operating conditions considered the data for steam biomass ratio (SBR) and equivalence ratio (ER) range from 0.6 to 10 and 0.1 to 0.4, respectively. In the study considered, steam is used as the gasifying agent with a product gas heating value of about 10-15 MJ/Nm{sup 3}, compared to an air gasification of biomass process with 3-6 MJ/Nm{sup 3}. The exergy efficiency value for the case study system is calculated to be 56.8%, while irreversibility and improvement potential rates are found to be 670.43 and 288.28 kW, respectively. Also, exergetic fuel and product rates of the downdraft gasifier are calculated as 1572.08 and 901.64 kW, while fuel depletion and productivity lack ratios are 43% and 74.3%, respectively. (author)

  5. Feasibility Study of Hydrogen Production at Existing Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Stephen Schey

    2009-07-01

    Cooperative Agreement DE-FC07-06ID14788 was executed between the U.S. Department of Energy, Electric Transportation Applications, and Idaho National Laboratory to investigate the economics of producing hydrogen by electrolysis using electricity generated by nuclear power. The work under this agreement is divided into the following four tasks: Task 1 – Produce Data and Analyses Task 2 – Economic Analysis of Large-Scale Alkaline Electrolysis Task 3 – Commercial-Scale Hydrogen Production Task 4 – Disseminate Data and Analyses. Reports exist on the prospect that utility companies may benefit from having the option to produce electricity or produce hydrogen, depending on market conditions for both. This study advances that discussion in the affirmative by providing data and suggesting further areas of study. While some reports have identified issues related to licensing hydrogen plants with nuclear plants, this study provides more specifics and could be a resource guide for further study and clarifications. At the same time, this report identifies other area of risks and uncertainties associated with hydrogen production on this scale. Suggestions for further study in some of these topics, including water availability, are included in the report. The goals and objectives of the original project description have been met. Lack of industry design for proton exchange membrane electrolysis hydrogen production facilities of this magnitude was a roadblock for a significant period. However, recent design breakthroughs have made costing this facility much more accurate. In fact, the new design information on proton exchange membrane electrolyzers scaled to the 1 kg of hydrogen per second electrolyzer reduced the model costs from $500 to $100 million. Task 1 was delayed when the original electrolyzer failed at the end of its economic life. However, additional valuable information was obtained when the new electrolyzer was installed. Products developed during this study

  6. Isolation of non-sulphur photosynthetic bacterial strains efficient in hydrogen production at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Singh, S.P.; Srivastava, S.C. (Banaras Hindu Univ., Varanasi (IN). Centre of Advanced Study in Botany)

    1991-01-01

    Four strains of non-sulphur photosynthetic bacteria were isolated from root zone associations of aquatic plants like Azolla, Salvinia and Eichhornia, as well as the deep-water rice. Based on the gross cell morphology and pigmentation, the isolates resembled Rhodopseudomonas sp. and have been designated as BHU strains 1 to 4, respectively. When subjected to elevated temperature (from 33-45{sup o}C), substantial growth/hydrogen production could be observed only in strains 1 and 4. Strains 2 and 3 on the other hand, showed diminished growth and negligible hydrogen photoproduction. The BHU strains 1 and 4 have been selected as the most active (thermostable) hydrogen producing strains of local origin as far as the Indian tropical climate is concerned. (author).

  7. Enhanced hydrogen production of Enterobacter aerogenes mutated by nuclear irradiation.

    Science.gov (United States)

    Cheng, Jun; Liu, Min; Song, Wenlu; Ding, Lingkan; Liu, Jianzhong; Zhang, Li; Cen, Kefa

    2017-03-01

    Nuclear irradiation was used for the first time to generate efficient mutants of hydrogen-producing bacteria Enterobacter aerogenes, which were screened with larger colour circles of more fermentative acid by-products. E. aerogenes cells were mutated by nuclear irradiation of (60)Co γ-rays. The screened E. aerogenes ZJU1 mutant with larger colour circles enhanced the hydrogenase activity from 89.8 of the wild strain to 157.4mLH2/(gDWh). The hereditary stability of the E. aerogenes ZJU1 mutant was certified after over ten generations of cultivation. The hydrogen yield of 301mLH2/gglucose with the mutant was higher by 81.8% than that of 166mL/gglucose with the wild strain. The peak hydrogen production rate of 27.2mL/(L·h) with the mutant was higher by 40.9% compared with that of 19.3mL/(L·h) with the wild strain. The mutant produced more acetate and butyrate but less ethanol compared with the wild strain during hydrogen fermentation.

  8. Radiolytic hydrogen production from process vessels in HB line - production rates compared to evolution rates and discussion of LASL reviews

    Energy Technology Data Exchange (ETDEWEB)

    Bibler, N.E.

    1992-11-12

    Hydrogen production from radiolysis of aqueous solutions can create a safety hazard since hydrogen is flammable. At times this production can be significant, especially in HB line where nitric acid solutions containing high concentrations of Pu-238, an intense alpha emitter, are processed. The hydrogen production rates from these solutions are necessary for safety analyses of these process systems. The methods and conclusions of hydrogen production rate tests are provided in this report.

  9. Solar to hydrogen: Compact and cost effective CPV field for rooftop operation and hydrogen production

    KAUST Repository

    Burhan, Muhammad

    2016-11-25

    Current commercial CPV systems are designed as large units which are targeted to be installed in open desert fields with high DNI availability. It appeared that the CPV is among some of those technologies which gained very little attention of people, with less customers and market. For conventional PV systems, the installations at the rooftop of commercial and residential buildings have a significant share in the total installed capacity of PV systems. That is why for most of the countries, the PV installations at the rooftop of commercial and residential buildings are aimed to be increased to half of total installed PV. On the other hand, there is no commercial CPV system available to be suitable for rooftop operation, giving motivation for the development of CPV field of compact systems. This paper discusses the development of a CPV field for the rooftop operation, comprising of compact CPV system with cost effective but highly accurate solar tracking sensor and wireless master slave control. In addition, the performance of the developed CPV systems is evaluated for production of hydrogen, which can be used as energy carrier or energy storage and a maximum solar to hydrogen efficiency of 18% is obtained. However, due to dynamic nature of the weather data and throughout the day variations in the performance of CPV and electrolyser, the solar to hydrogen performance is proposed to be reported as daily and long term average efficiency. The CPV-Hydrogen system showed daily average conversion efficiency of 15%, with solar to hydrogen production rate of 218 kW h/kg.

  10. Photoelectrochemical Hydrogen Production Using New Combinatorial Chemistry Derived Materials

    Energy Technology Data Exchange (ETDEWEB)

    Jaramillo, Thomas F.; Baeck, Sung-Hyeon; Kleiman-Shwarsctein, Alan; Stucky, Galen D. (PI); McFarland, Eric W. (PI)

    2004-10-25

    Solar photoelectrochemical water-splitting has long been viewed as one of the “holy grails” of chemistry because of its potential impact as a clean, renewable method of fuel production. Several known photocatalytic semiconductors can be used; however, the fundamental mechanisms of the process remain poorly understood and no known material has the required properties for cost effective hydrogen production. In order to investigate morphological and compositional variations in metal oxides as they relate to opto-electrochemical properties, we have employed a combinatorial methodology using automated, high-throughput, electrochemical synthesis and screening together with conventional solid-state methods. This report discusses a number of novel, high-throughput instruments developed during this project for the expeditious discovery of improved materials for photoelectrochemical hydrogen production. Also described within this report are results from a variety of materials (primarily tungsten oxide, zinc oxide, molybdenum oxide, copper oxide and titanium dioxide) whose properties were modified and improved by either layering, inter-mixing, or doping with one or more transition metals. Furthermore, the morphologies of certain materials were also modified through the use of structure directing agents (SDA) during synthesis to create mesostructures (features 2-50 nm) that increased surface area and improved rates of hydrogen production.

  11. Thermodynamic evaluation of hydrogen production via bioethanol steam reforming

    Science.gov (United States)

    Tasnadi-Asztalos, Zsolt; Cormos, Ana-Maria; Imre-Lucaci, Árpád; Cormos, Cǎlin C.

    2013-11-01

    In this article, a thermodynamic analysis for bioethanol steam reforming for hydrogen production is presented. Bioethanol is a newly proposed renewable energy carrier mainly produced from biomass fermentation. Reforming of bioethanol provides a promising method for hydrogen production from renewable resources. Steam reforming of ethanol (SRE) takes place under the action of a metal catalyst capable of breaking C-C bonds into smaller molecules. A large domain for the water/bioethanol molar ratio as well as the temperature and average pressure has been used in the present work. The interval of investigated temperature was 100-800°C, the pressure was in the range of 1-10 bar and the molar ratio was between 3-25. The variations of gaseous species concentration e.g. H2, CO, CO2, CH4 were analyzed. The concentrations of the main products (H2 and CO) at lower temperature are smaller than the ones at higher temperature due to by-products formation (methane, carbon dioxide, acetylene etc.). The concentration of H2 obtained in the process using high molar ratio (>20) is higher than the one at small molar ratio (near stoichiometric). When the pressure is increased the hydrogen concentration decreases. The results were compared with literature data for validation purposes.

  12. Thermodynamic evaluation of hydrogen production via bioethanol steam reforming

    Energy Technology Data Exchange (ETDEWEB)

    Tasnadi-Asztalos, Zsolt; Cormos, Ana-Maria; Imre-Lucaci, Árpád; Cormos, Călin C. [Babes-Bolyai University, Faculty of Chemistry and Chemical Engineering, Arany Janos 11, RO-400028, Cluj-Napoca (Romania)

    2013-11-13

    In this article, a thermodynamic analysis for bioethanol steam reforming for hydrogen production is presented. Bioethanol is a newly proposed renewable energy carrier mainly produced from biomass fermentation. Reforming of bioethanol provides a promising method for hydrogen production from renewable resources. Steam reforming of ethanol (SRE) takes place under the action of a metal catalyst capable of breaking C-C bonds into smaller molecules. A large domain for the water/bioethanol molar ratio as well as the temperature and average pressure has been used in the present work. The interval of investigated temperature was 100-800°C, the pressure was in the range of 1-10 bar and the molar ratio was between 3-25. The variations of gaseous species concentration e.g. H{sub 2}, CO, CO{sub 2}, CH{sub 4} were analyzed. The concentrations of the main products (H{sub 2} and CO) at lower temperature are smaller than the ones at higher temperature due to by-products formation (methane, carbon dioxide, acetylene etc.). The concentration of H2 obtained in the process using high molar ratio (>20) is higher than the one at small molar ratio (near stoichiometric). When the pressure is increased the hydrogen concentration decreases. The results were compared with literature data for validation purposes.

  13. Solar-driven hydrogen production in green algae.

    Science.gov (United States)

    Burgess, Steven J; Tamburic, Bojan; Zemichael, Fessehaye; Hellgardt, Klaus; Nixon, Peter J

    2011-01-01

    The twin problems of energy security and global warming make hydrogen an attractive alternative to traditional fossil fuels with its combustion resulting only in the release of water vapor. Biological hydrogen production represents a renewable source of the gas and can be performed by a diverse range of microorganisms from strict anaerobic bacteria to eukaryotic green algae. Compared to conventional methods for generating H(2), biological systems can operate at ambient temperatures and pressures without the need for rare metals and could potentially be coupled to a variety of biotechnological processes ranging from desalination and waste water treatment to pharmaceutical production. Photobiological hydrogen production by microalgae is particularly attractive as the main inputs for the process (water and solar energy) are plentiful. This chapter focuses on recent developments in solar-driven H(2) production in green algae with emphasis on the model organism Chlamydomonas reinhardtii. We review the current methods used to achieve sustained H(2) evolution and discuss possible approaches to improve H(2) yields, including the optimization of culturing conditions, reducing light-harvesting antennae and targeting auxiliary electron transport and fermentative pathways that compete with the hydrogenase for reductant. Finally, industrial scale-up is discussed in the context of photobioreactor design and the future prospects of the field are considered within the broader context of a biorefinery concept.

  14. IEA hydrogen agreement, task 15: photobiological hydrogen production - an international collaboration

    Energy Technology Data Exchange (ETDEWEB)

    Lindblad, P. [Uppsala Univ., Dept. of Physiological Botany, Uppsala (Sweden); Asada, Y. [Industrial Techn Centre of Okayama Prefecture, Okayama (Japan); Benemann, J. [Univ. of California, Dept. of Plant and Microbial Biology, Berkeley, California (United States); Hallenbeck, P. [Univ. Of Montreal, Dept. of Microbiology and Immunolgy, Montreal, Quebec (Canada); Melis, A. [Univ. of California, Dept. of Plant and Microbial Biology, Berkeley, California (United States); Miyake, J. [National Institute for Advanced Interdisciplinary Research, Tsukuba, Ibaraki (Japan); Seibert, M. [Basic Sciences Center, National Renewable Energy Lab., Golden, Colorado (United States); Skulberg, O. [Norwegian Inst. of Water Research, Kjelsas, Oslo (Norway)

    2000-05-01

    Biological hydrogen production, the production of H{sub 2} by microorganisms, has been an active field of basic and applied research for many years. Realization of practical processes for photobiological hydrogen production from water using solar energy would result in a major, novel source of sustainable and renewable energy, without greenhouse gas emissions or environmental pollution. However, development of such processes requires significant scientific and technological advances, and long-term basic and applied R and D. This International Energy Agency (lEA) Task covers research areas and needs at the interface of basic and applied R and D which are of mutual interest to the countries and researchers participating in the lEA Hydrogen Agreement. The overall objective is to sufficiently advance the basic and early-stage applied science in this area of research over the next five years to allow an evaluation of the potential of such a technology to be developed as a practical renewable energy source for the 21st Century. (author)

  15. Hydrogen.

    Science.gov (United States)

    Bockris, John O'M

    2011-11-30

    The idea of a "Hydrogen Economy" is that carbon containing fuels should be replaced by hydrogen, thus eliminating air pollution and growth of CO₂ in the atmosphere. However, storage of a gas, its transport and reconversion to electricity doubles the cost of H₂ from the electrolyzer. Methanol made with CO₂ from the atmosphere is a zero carbon fuel created from inexhaustible components from the atmosphere. Extensive work on the splitting of water by bacteria shows that if wastes are used as the origin of feed for certain bacteria, the cost for hydrogen becomes lower than any yet known. The first creation of hydrogen and electricity from light was carried out in 1976 by Ohashi et al. at Flinders University in Australia. Improvements in knowledge of the structure of the semiconductor-solution system used in a solar breakdown of water has led to the discovery of surface states which take part in giving rise to hydrogen (Khan). Photoelectrocatalysis made a ten times increase in the efficiency of the photo production of hydrogen from water. The use of two electrode cells; p and n semiconductors respectively, was first introduced by Uosaki in 1978. Most photoanodes decompose during the photoelectrolysis. To avoid this, it has been necessary to create a transparent shield between the semiconductor and its electronic properties and the solution. In this way, 8.5% at 25 °C and 9.5% at 50 °C has been reached in the photo dissociation of water (GaP and InAs) by Kainthla and Barbara Zeleney in 1989. A large consortium has been funded by the US government at the California Institute of Technology under the direction of Nathan Lewis. The decomposition of water by light is the main aim of this group. Whether light will be the origin of the post fossil fuel supply of energy may be questionable, but the maximum program in this direction is likely to come from Cal. Tech.

  16. Solar photochemical production of HBr for off-peak electrolytic hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Heaton, H. [Solar Reactor Technologies Inc., Miami, FL (United States)

    1996-10-01

    Progress is reported on the development of a unique and innovative hydrogen production concept utilizing renewable (Solar) energy and incorporating energy storage. The concept is based on a solar-electrolytic system for production of hydrogen and oxygen. It employs water, bromine, solar energy, and supplemental electrical power. The process consumes only water, sunlight and off-peak electricity, and produces only hydrogen, oxygen, and peaking electrical power. No pollutants are emitted, and fossil fuels are not consumed. The concept is being developed by Solar Reactor Technologies, Inc., (SRT) under the auspices of a Cooperative Agreement with the U.S. Department of Energy (DOE).

  17. Final Report: Hydrogen Production Pathways Cost Analysis (2013 – 2016)

    Energy Technology Data Exchange (ETDEWEB)

    James, Brian David [Strategic Analysis Inc., Arlington, VA (United States); DeSantis, Daniel Allan [Strategic Analysis Inc., Arlington, VA (United States); Saur, Genevieve [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-09-30

    This report summarizes work conducted under a three year Department of Energy (DOE) funded project to Strategic Analysis, Inc. (SA) to analyze multiple hydrogen (H2) production technologies and project their corresponding levelized production cost of H2. The analysis was conducted using the H2A Hydrogen Analysis Tool developed by the DOE and National Renewable Energy Laboratory (NREL). The project was led by SA but conducted in close collaboration with the NREL and Argonne National Laboratory (ANL). In-depth techno-economic analysis (TEA) of five different H2 production methods was conducted. These TEAs developed projections for capital costs, fuel/feedstock usage, energy usage, indirect capital costs, land usage, labor requirements, and other parameters, for each H2 production pathway, and use the resulting cost and system parameters as inputs into the H2A discounted cash flow model to project the production cost of H2 ($/kgH2). Five technologies were analyzed as part of the project and are summarized in this report: Proton Exchange Membrane technology (PEM), High temperature solid oxide electrolysis cell technology (SOEC), Dark fermentation of biomass for H2 production, H2 production via Monolithic Piston-Type Reactors with rapid swing reforming and regeneration reactions, and Reformer-Electrolyzer-Purifier (REP) technology developed by Fuel Cell Energy, Inc. (FCE).

  18. Self-assembling hydrogel scaffolds for photocatalytic hydrogen production

    Science.gov (United States)

    Weingarten, Adam S.; Kazantsev, Roman V.; Palmer, Liam C.; McClendon, Mark; Koltonow, Andrew R.; Samuel, Amanda P. S.; Kiebala, Derek J.; Wasielewski, Michael R.; Stupp, Samuel I.

    2014-11-01

    Integration into a soft material of all the molecular components necessary to generate storable fuels is an interesting target in supramolecular chemistry. The concept is inspired by the internal structure of photosynthetic organelles, such as plant chloroplasts, which colocalize molecules involved in light absorption, charge transport and catalysis to create chemical bonds using light energy. We report here on the light-driven production of hydrogen inside a hydrogel scaffold built by the supramolecular self-assembly of a perylene monoimide amphiphile. The charged ribbons formed can electrostatically attract a nickel-based catalyst, and electrolyte screening promotes gelation. We found the emergent phenomenon that screening by the catalyst or the electrolytes led to two-dimensional crystallization of the chromophore assemblies and enhanced the electronic coupling among the molecules. Photocatalytic production of hydrogen is observed in the three-dimensional environment of the hydrogel scaffold and the material is easily placed on surfaces or in the pores of solid supports.

  19. Yttrium bismuth titanate pyrochlore mixed oxides for photocatalytic hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Merka, Oliver

    2012-10-18

    In this work, the sol-gel synthesis of new non-stoichiometric pyrochlore titanates and their application in photocatalytic hydrogen production is reported. Visible light response is achieved by introducing bismuth on the A site or by doping the B site by transition metal cations featuring partially filled d orbitals. This work clearly focusses on atomic scale structural changes induced by the systematical introduction of non-stoichiometry in pyrochlore mixed oxides and the resulting influence on the activity in photocatalytic hydrogen production. The materials were characterized in detail regarding their optical properties and their atomic structure. The pyrochlore structure tolerates tremendous stoichiometry variations. The non-stoichiometry in A{sub 2}O{sub 3} rich compositions is compensated by distortions in the cationic sub-lattice for the smaller Y{sup 3+} cation and by evolution of a secondary phase for the larger Bi{sup 3+} cation on the A site. For TiO{sub 2} rich compositions, the non-stoichiometry leads to a special vacancy formation in the A and optionally O' sites. It is shown that pyrochlore mixed oxides in the yttrium bismuth titanate system represent very active and promising materials for photocatalytic hydrogen production, if precisely and carefully tuned. Whereas Y{sub 2}Ti{sub 2}O{sub 7} yields stable hydrogen production rates over time, the bismuth richer compounds of YBiTi{sub 2}O{sub 7} and Bi{sub 2}Ti{sub 2}O{sub 7} are found to be not stable under irradiation. This drawback is overcome by applying a special co-catalyst system consisting of a precious metal core and a Cr{sub 2}O{sub 3} shell on the photocatalysts.

  20. Photoelectrochemical based direct conversion systems for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Khaselev, O.; Bansal, A.; Kocha, S.; Turner, J.A. [National Renewable Energy Lab., Golden, CO (United States)

    1998-08-01

    With an eye towards developing a photoelectrochemical system for hydrogen production using sunlight as the only energy input, two types of systems were studied, both involving multijunction devices. One set of cells consisted of a-Si triple junctions and the other a GaInP{sub 2}/GaAs tandem cell combination. Additional investigations were carried out on semiconductor surface modifications to move semiconductor band edges to more favorable energetic positions.

  1. Hydrogen production by catalytic partial oxidation of methane

    OpenAIRE

    Enger, Bjørn Christian

    2008-01-01

    Hydrogen production by catalytic partial oxidation of natural gas was investigated using tools ranging from theoretical calculations to experimental work and sophisticated characterization techniques.Catalytic partial oxidation (CPO) was carried out in a conventional continuous flow experimental apparatus using a xed-bed reactor, and operating at 1 atm and furnace temperatures in the range from ambient to 1073 K. The feed typically consisted of a mixture of methane and air, with a CH4/O2 rati...

  2. Advances in ethanol reforming for the production of hydrogen

    Directory of Open Access Journals (Sweden)

    Laura Guerrero

    2014-06-01

    Full Text Available Catalytic steam reforming of ethanol (SRE is a promising route for the production of renewable hydrogen (H2. This article reviews the influence of doping supported-catalysts used in SRE on the conversion of ethanol, selectivity for H2, and stability during long reaction periods. In addition, promising new technologies such as membrane reactors and electrochemical reforming for performing SRE are presented.

  3. Studies of the use of heat from high temperature nuclear sources for hydrogen production processes

    Science.gov (United States)

    Farbman, G. H.

    1976-01-01

    Future uses of hydrogen and hydrogen production processes that can meet the demand for hydrogen in the coming decades were considered. To do this, a projection was made of the market for hydrogen through the year 2000. Four hydrogen production processes were selected, from among water electrolysis, fossil based and thermochemical water decomposition systems, and evaluated, using a consistent set of ground rules, in terms of relative performance, economics, resource requirements, and technology status.

  4. Dispatchable hydrogen production at the forecourt for electricity grid balancing

    Science.gov (United States)

    Rahil, Abdulla; Gammon, Rupert; Brown, Neil

    2017-02-01

    The rapid growth of renewable energy (RE) generation and its integration into electricity grids has been motivated by environmental issues and the depletion of fossil fuels. For the same reasons, an alternative to hydrocarbon fuels is needed for vehicles; hence the anticipated uptake of electric and fuel cell vehicles. High penetrations of RE generators with variable and intermittent output threaten to destabilise electricity networks by reducing the ability to balance electricity supply and demand. This can be greatly mitigated by the use of energy storage and demand-side response (DSR) techniques. Hydrogen production by electrolysis is a promising option for providing DSR as well as an emission-free vehicle fuel. Tariff structures can be used to incentivise the operating of electrolysers as controllable (dispatchable) loads. This paper compares the cost of hydrogen production by electrolysis at garage forecourts under both dispatchable and continuous operation, while ensuring no interruption of fuel supply to fuel cell vehicles. An optimisation algorithm is applied to investigate a hydrogen refueling station in both dispatchable and continuous operation. Three scenarios are tested to see whether a reduced off-peak electricity price could lower the cost of electrolytic hydrogen. These scenarios are: 1) "Standard Continuous", where the electrolyser is operated continuously on a standard all-day tariff of 12p/kWh; 2) "Off-peak Only", where it runs only during off-peak periods in a 2-tier tariff system at the lower price of 5p/kWh; and 3) "2-Tier Continuous", operating continuously and paying a low tariff at off- peak times and a high tariff at other times. This study uses the Libyan coastal city of Derna as a case study. The cheapest electricity cost per kg of hydrogen produced was £2.8, which occurred in Scenario 2. The next cheapest, at £5.8 - £6.3, was in Scenario 3, and the most expensive was £6.8/kg in Scenario 1.

  5. Hydrogen production from proteins via electrohydrogenesis in microbial electrolysis cells.

    Science.gov (United States)

    Lu, Lu; Xing, Defeng; Xie, Tianhui; Ren, Nanqi; Logan, Bruce E

    2010-08-15

    Microorganisms can produce hydrogen gas (H(2)) at high rates by fermentation of carbohydrates, but not from proteins. However, it is possible to produce H(2) at high rates and yields from proteins by electrohydrogenesis in microbial electrolysis cells (MECs). Hydrogen gas was generated using bovine serum albumin (BSA, 700 mg/L) in a single-chamber MEC at a rate of Q=0.42+/-0.07 m(3)/m(3)/day and a yield of Y(H2) = 21.0 +/- 5.0 mmol-H2/g-COD, with an energy recovery (relative to electrical input) of eta(E)=75+/-12% (applied voltage of 0.6 V). Hydrogen production was substantially reduced using a complex protein (peptone) under the same conditions, to Q=0.05+/-0.01 m(3)/m(3)/day, YH2 = 2.6 +/- 0.1 mmol-H2/g-COD, and eta(E)=14+/-3%. There was good removal of organic matter for both substrates in terms of either protein (87+/-6 -97 +/-2%) or total COD (86+/-2 - 91+/-2%). Electron recycling likely occurred as Coulombic efficiencies exceeded 100% using BSA. The use of a two-chamber design, with either a CEM or AEM membrane, reduced the hydrogen production rate, but did not appreciably affect the hydrogen yield or energy efficiency. When an MEC was first acclimated to acetate, and then switched to BSA, performance was substantially reduced and was similar to that obtained using peptone. These results demonstrate that electrohydrogenesis can be used to produce H(2) from proteins, and it can also be used as a method for treatment of protein-containing wastewaters.

  6. Bio-hydrogen production from hyacinth by anaerobic fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Cheng Jun; Zhou Junhu; Qi Feng; Xie Binfei; Cen Kefa [State Key Laboratory of Clean Energy Utilization, Zhejiang University No.38 Zheda Road, Hangzhou 310027, (China)

    2006-07-01

    The bio-hydrogen production from hyacinth by anaerobic fermentation of digested sludge is studied in this paper. The compositions of bio-gases and volatile fatty acids in fermentation liquids are determined on TRACE 2000 gas chromatography. It is found that the H{sub 2} concentration in the biogas is 10%-20% and no CH{sub 4} is detected. The bio-hydrogen production from hyacinth with the initial pH value of 5.5 is higher than that with the initial pH value of 4.5. The fermentation temperature of 55 C is better than that of 35 C, while the weight ratio of hyacinth to microorganism of 1:1 is better than that of 3:7. The highest hydrogen production of 122.3 mL/g is obtained when the initial pH value of fermentation solution is 5.5, the fermentation temperature is 55 C and the weight ratio of hyacinth to microorganism is 1:1. (authors)

  7. Inhibitory effect of ethanol, acetic acid, propionic acid and butyric acid on fermentative hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Bo; Wan, Wei; Wang, Jianlong [Laboratory of Environmental Technology, INET, Tsinghua University, Beijing 100084 (China)

    2008-12-15

    The inhibitory effect of added ethanol, acetic acid, propionic acid and butyric acid on fermentative hydrogen production by mixed cultures was investigated in batch tests using glucose as substrate. The experimental results showed that, at 35 C and initial pH 7.0, during the fermentative hydrogen production, the substrate degradation efficiency, hydrogen production potential, hydrogen yield and hydrogen production rate all trended to decrease with increasing added ethanol, acetic acid, propionic acid and butyric acid concentration from 0 to 300 mmol/L. The inhibitory effect of added ethanol on fermentative hydrogen production was smaller than those of added acetic acid, propionic acid and butyric acid. The modified Han-Levenspiel model could describe the inhibitory effects of added ethanol, acetic acid, propionic acid and butyric acid on fermentative hydrogen production rate in this study successfully. The modified Logistic model could describe the progress of cumulative hydrogen production. (author)

  8. 40 CFR 415.420 - Applicability; description of the hydrogen cyanide production subcategory.

    Science.gov (United States)

    2010-07-01

    ... hydrogen cyanide production subcategory. 415.420 Section 415.420 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Hydrogen Cyanide Production Subcategory § 415.420 Applicability; description of the hydrogen cyanide production subcategory. This subpart applies to discharges to waters of the United States...

  9. 40 CFR 415.90 - Applicability; description of the hydrogen peroxide production subcategory.

    Science.gov (United States)

    2010-07-01

    ... hydrogen peroxide production subcategory. 415.90 Section 415.90 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Hydrogen Peroxide Production Subcategory § 415.90 Applicability; description of the hydrogen peroxide production subcategory. The provisions of this subpart are applicable to...

  10. Safety considerations for continuous hydrogen production test apparatus with capacity of 50 N-litter hydrogen per hour

    Energy Technology Data Exchange (ETDEWEB)

    Onuki, Kaoru; Akino, Norio; Shimizu, Saburo; Nakajima, Hayato; Higashi, Shunichi; Kubo, Shinji [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

    2001-03-01

    Since the thermochemical hydrogen production Iodine-Sulfur process decomposes water into hydrogen and oxygen using toxic chemicals such as sulfuric acid, iodine and hydriodic acid, safety considerations are very important in its research and development. Therefore, before construction of continuous hydrogen production test apparatus with capacity of 50 N-litter hydrogen per hour, comprehensive safety considerations were carried out to examine the design and construction works of the test apparatus, and the experimental plans using the apparatus. Emphasis was given on the safety considerations on prevention of breakage of glasswares and presumable abnormalities, accidents and their countermeasures. This report summarizes the results of the considerations. (author)

  11. Pathway of Fermentative Hydrogen Production by Sulfate-reducing Bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Wall, Judy D. [Univ. of Missouri, Columbia, MO (United States)

    2015-02-16

    Biofuels are a promising source of sustainable energy. Such biofuels are intermediate products of microbial metabolism of renewable substrates, in particular, plant biomass. Not only are alcohols and solvents produced in this degradative process but energy-rich hydrogen as well. Non photosynthetic microbial hydrogen generation from compounds other than sugars has not been fully explored. We propose to examine the capacity of the abundant soil anaerobes, sulfate-reducing bacteria, for hydrogen generation from organic acids. These apparently simple pathways have yet to be clearly established. Information obtained may facilitate the exploitation of other microbes not yet readily examined by molecular tools. Identification of the flexibility of the metabolic processes to channel reductant to hydrogen will be useful in consideration of practical applications. Because the tools for genetic and molecular manipulation of sulfate-reducing bacteria of the genus Desulfovibrio are developed, our efforts will focus on two strains, D. vulgaris Hildenborough and Desulfovibrio G20.Therefore total metabolism, flux through the pathways, and regulation are likely to be limiting factors which we can elucidate in the following experiments.

  12. Continuous fermentative hydrogen production in different process conditions

    Energy Technology Data Exchange (ETDEWEB)

    Nasirian, N. [Islamic Azad Univ., Shoushtar (Iran, Islamic Republic of). Dept. of Agricultural Mechanization; Almassi, M.; Minaee, S. [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Dept. of Agricultural Mechanization; Widmann, R. [Duisburg-Essen Univ., Essen (Germany). Dept. of Environmental Engineering, Waste and Water

    2010-07-01

    This paper reported on a study in which hydrogen was produced by fermentation of biomass. A continuous process using a non-sterile substrate with a readily available mixed microflora was used on heat treated digested sewage sludge from a wastewater treatment plant. Hydrogen was produced from waste sugar at a pH of 5.2 and a temperature of 37 degrees C. An experimental setup of three 5.5 L working volume continuously stirred tank reactors (CSTR) in different stirring speeds were constructed and operated at 7 different hydraulic retention times (HRTs) and different organic loading rates (OLR). Dissolved organic carbon was examined. The results showed that the stirring speed of 135 rpm had a beneficial effect on hydrogen fermentation. The best performance was obtained in 135 rpm and 8 h of HRT. The amount of gas varied with different OLRs, but could be stabilized on a high level. Methane was not detected when the HRT was less than 16 h. The study identified the reactor in which the highest specific rate of hydrogen production occurred.

  13. Techno Economic Analysis of Hydrogen Production by gasification of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Francis Lau

    2002-12-01

    Biomass represents a large potential feedstock resource for environmentally clean processes that produce power or chemicals. It lends itself to both biological and thermal conversion processes and both options are currently being explored. Hydrogen can be produced in a variety of ways. The majority of the hydrogen produced in this country is produced through natural gas reforming and is used as chemical feedstock in refinery operations. In this report we will examine the production of hydrogen by gasification of biomass. Biomass is defined as organic matter that is available on a renewable basis through natural processes or as a by-product of processes that use renewable resources. The majority of biomass is used in combustion processes, in mills that use the renewable resources, to produce electricity for end-use product generation. This report will explore the use of hydrogen as a fuel derived from gasification of three candidate biomass feedstocks: bagasse, switchgrass, and a nutshell mix that consists of 40% almond nutshell, 40% almond prunings, and 20% walnut shell. In this report, an assessment of the technical and economic potential of producing hydrogen from biomass gasification is analyzed. The resource base was assessed to determine a process scale from feedstock costs and availability. Solids handling systems were researched. A GTI proprietary gasifier model was used in combination with a Hysys(reg. sign) design and simulation program to determine the amount of hydrogen that can be produced from each candidate biomass feed. Cost estimations were developed and government programs and incentives were analyzed. Finally, the barriers to the production and commercialization of hydrogen from biomass were determined. The end-use of the hydrogen produced from this system is small PEM fuel cells for automobiles. Pyrolysis of biomass was also considered. Pyrolysis is a reaction in which biomass or coal is partially vaporized by heating. Gasification is a more

  14. Advanced Electrochemical Technologies for Hydrogen Production by Alternative Thermochemical Cycles

    Energy Technology Data Exchange (ETDEWEB)

    Lvov, Serguei; Chung, Mike; Fedkin, Mark; Lewis, Michele; Balashov, Victor; Chalkova, Elena; Akinfiev, Nikolay; Stork, Carol; Davis, Thomas; Gadala-Maria, Francis; Stanford, Thomas; Weidner, John; Law, Victor; Prindle, John

    2011-01-06

    Hydrogen fuel is a potentially major solution to the problem of climate change, as well as addressing urban air pollution issues. But a key future challenge for hydrogen as a clean energy carrier is a sustainable, low-cost method of producing it in large capacities. Most of the world's hydrogen is currently derived from fossil fuels through some type of reforming processes. Nuclear hydrogen production is an emerging and promising alternative to the reforming processes for carbon-free hydrogen production in the future. This report presents the main results of a research program carried out by a NERI Consortium, which consisted of Penn State University (PSU) (lead), University of South Carolina (USC), Tulane University (TU), and Argonne National Laboratory (ANL). Thermochemical water decomposition is an emerging technology for large-scale production of hydrogen. Typically using two or more intermediate compounds, a sequence of chemical and physical processes split water into hydrogen and oxygen, without releasing any pollutants externally to the atmosphere. These intermediate compounds are recycled internally within a closed loop. While previous studies have identified over 200 possible thermochemical cycles, only a few have progressed beyond theoretical calculations to working experimental demonstrations that establish scientific and practical feasibility of the thermochemical processes. The Cu-Cl cycle has a significant advantage over other cycles due to lower temperature requirements – around 530 °C and below. As a result, it can be eventually linked with the Generation IV thermal power stations. Advantages of the Cu-Cl cycle over others include lower operating temperatures, ability to utilize low-grade waste heat to improve energy efficiency, and potentially lower cost materials. Another significant advantage is a relatively low voltage required for the electrochemical step (thus low electricity input). Other advantages include common chemical agents and

  15. Critical Research for Cost-Effective Photoelectrochemical Production of Hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Liwei [Midwest Optoelectronics, LLC, Toledo, OH (United States); Deng, Xunming [Univ. of Toledo, OH (United States); Abken, Anka [Midwest Optoelectronics, LLC, Toledo, OH (United States); Cao, Xinmin [Midwest Optoelectronics, LLC, Toledo, OH (United States); Du, Wenhui [Midwest Optoelectronics, LLC, Toledo, OH (United States); Vijh, Aarohi [Xunlight Corporation, Toledo, OH (United States); Ingler, William [Univ. of Toledo, OH (United States); Chen, Changyong [Univ. of Toledo, OH (United States); Fan, Qihua [Univ. of Toledo, OH (United States); Collins, Robert [Univ. of Toledo, OH (United States); Compaan, Alvin [Univ. of Toledo, OH (United States); Yan, Yanfa [Univ. of Toledo, OH (United States); Giolando, Dean [Univ. of Toledo, OH (United States); Turner, John [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-10-29

    The objective of this project is to develop critical technologies required for cost-effective production of hydrogen from sunlight and water using a-Si triple junction solar cell based photo-electrodes. In this project, Midwest Optoelectronics, LLC (MWOE) and its collaborating organizations utilize triple junction a-Si thin film solar cells as the core element to fabricate photoelectrochemical (PEC) cells. Triple junction a-Si/a-SiGe/a-SiGe solar cell is an ideal material for making cost-effective PEC system which uses sun light to split water and generate hydrogen. It has the following key features: 1) It has an open circuit voltage (Voc ) of ~ 2.3V and has an operating voltage around 1.6V. This is ideal for water splitting. There is no need to add a bias voltage or to inter-connect more than one solar cell. 2) It is made by depositing a-Si/a-SiGe/aSi-Ge thin films on a conducting stainless steel substrate which can serve as an electrode. When we immerse the triple junction solar cells in an electrolyte and illuminate it under sunlight, the voltage is large enough to split the water, generating oxygen at the Si solar cell side (for SS/n-i-p/sunlight structure) and hydrogen at the back, which is stainless steel side. There is no need to use a counter electrode or to make any wire connection. 3) It is being produced in large rolls of 3ft wide and up to 5000 ft long stainless steel web in a 25MW roll-to-roll production machine. Therefore it can be produced at a very low cost. After several years of research with many different kinds of material, we have developed promising transparent, conducting and corrosion resistant (TCCR) coating material; we carried out extensive research on oxygen and hydrogen generation catalysts, developed methods to make PEC electrode from production-grade a-Si solar cells; we have designed and tested various PEC module cases and carried out extensive outdoor testing; we were able to obtain a solar to hydrogen conversion efficiency (STH

  16. Characterization and optimization of hydrogen production by a salt water blue-green alga Oscillatoria sp. Miami BG 7. II - Use of immobilization for enhancement of hydrogen production

    Science.gov (United States)

    Phlips, E. J.; Mitsui, A.

    1986-01-01

    The technique of cellular immobilization was applied to the process of hydrogen photoproduction of nonheterocystous, filamentous marine blue-green alga, Oscillatoria sp. Miami BG 7. Immobilization with agar significantly improved the rate and longevity of hydrogen production, compared to free cell suspensions. Rates of H2 production in excess of 13 microliters H2 mg dry/wt h were observed and hydrogen production was sustained for three weeks. Immobilization also provided some stabilization to environmental variability and was adaptable to outdoor light conditions. In general, immobilization provides significant advantages for the production and maintenance of hydrogen photoproduction for this strain.

  17. Two-dimensional simulation of hydrogen iodide decomposition reaction using fluent code for hydrogen production using nuclear technology

    Directory of Open Access Journals (Sweden)

    Jung-Sik Choi

    2015-06-01

    Full Text Available The operating characteristics of hydrogen iodide (HI decomposition for hydrogen production were investigated using the commercial computational fluid dynamics code, and various factors, such as hydrogen production, heat of reaction, and temperature distribution, were studied to compare device performance with that expected for device development. Hydrogen production increased with an increase of the surface-to-volume (STV ratio. With an increase of hydrogen production, the reaction heat increased. The internal pressure and velocity of the HI decomposer were estimated through pressure drop and reducing velocity from the preheating zone. The mass of H2O was independent of the STV ratio, whereas that of HI decreased with increasing STV ratio.

  18. Thermochemical hydrogen production via a cycle using barium and sulfur - Reaction between barium sulfide and water

    Science.gov (United States)

    Ota, K.; Conger, W. L.

    1977-01-01

    The reaction between barium sulfide and water, a reaction found in several sulfur based thermochemical cycles, was investigated kinetically at 653-866 C. Gaseous products were hydrogen and hydrogen sulfide. The rate determining step for hydrogen formation was a surface reaction between barium sulfide and water. An expression was derived for the rate of hydrogen formation.

  19. Effect of ammonia concentration on fermentative hydrogen production by mixed cultures.

    Science.gov (United States)

    Wang, Bo; Wan, Wei; Wang, Jianlong

    2009-02-01

    The effect of ammonia concentration ranging from 0 to 10 g N/L on fermentative hydrogen production by mixed cultures was investigated in batch tests using glucose as substrate at 35 degrees C and initial pH 7.0. The experimental results showed that during the fermentative hydrogen production, the substrate degradation efficiency increased with increasing ammonia concentration from 0 to 0.01 g N/L. The hydrogen production potential, hydrogen yield and average hydrogen production rate increased with increasing ammonia concentration from 0 to 0.1g N/L. The maximum hydrogen production potential of 291.4 mL, maximum hydrogen yield of 298.8 mL/g glucose and maximum average hydrogen production rate of 8.5 mL/h were all obtained at the ammonia concentration of 0.1g N/L.

  20. Materials for Hydrogen Production with Integrated CO2 Capture

    Science.gov (United States)

    van den Brink, Ruud W.; de Bruijn, Frank A.

    2009-09-01

    Palladium-based membrane reactors and sorption-enhanced water-gas shift are two promising technologies for efficient production of hydrogen with integrated CO2 capture. This paper discusses material issues of the two crucial materials of these technologies: the membrane and the CO2 sorbent. For Pd and Pd-alloy membranes the major issues concern the stability of the membrane and the poisoning of the membrane surface by compound such as sulfur and carbon monoxide. Both issues are addressed by research into novel Pd-alloys. For the potassium-promoted hydrotalcite CO2 sorbents used in sorption-enhanced water gas shift, the main challenges are a high CO2 adsorption capacity, chemical and mechanical stability, and low steam use for sorbent regeneration. Promising results have recently been reported for several of these challenges. For both hydrogen-selective membranes and CO2 sorbents, the interaction of the materials with sulfur is an import issue to enable their use in the production of hydrogen from coal.

  1. Chemical Hydride Slurry for Hydrogen Production and Storage

    Energy Technology Data Exchange (ETDEWEB)

    McClaine, Andrew W

    2008-09-30

    The purpose of this project was to investigate and evaluate the attractiveness of using a magnesium chemical hydride slurry as a hydrogen storage, delivery, and production medium for automobiles. To fully evaluate the potential for magnesium hydride slurry to act as a carrier of hydrogen, potential slurry compositions, potential hydrogen release techniques, and the processes (and their costs) that will be used to recycle the byproducts back to a high hydrogen content slurry were evaluated. A 75% MgH2 slurry was demonstrated, which was just short of the 76% goal. This slurry is pumpable and storable for months at a time at room temperature and pressure conditions and it has the consistency of paint. Two techniques were demonstrated for reacting the slurry with water to release hydrogen. The first technique was a continuous mixing process that was tested for several hours at a time and demonstrated operation without external heat addition. Further work will be required to reduce this design to a reliable, robust system. The second technique was a semi-continuous process. It was demonstrated on a 2 kWh scale. This system operated continuously and reliably for hours at a time, including starts and stops. This process could be readily reduced to practice for commercial applications. The processes and costs associated with recycling the byproducts of the water/slurry reaction were also evaluated. This included recovering and recycling the oils of the slurry, reforming the magnesium hydroxide and magnesium oxide byproduct to magnesium metal, hydriding the magnesium metal with hydrogen to form magnesium hydride, and preparing the slurry. We found that the SOM process, under development by Boston University, offers the lowest cost alternative for producing and recycling the slurry. Using the H2A framework, a total cost of production, delivery, and distribution of $4.50/kg of hydrogen delivered or $4.50/gge was determined. Experiments performed at Boston

  2. Hydrogen production via methane decomposition on Raney-type catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Figueiredo, J.L.; Orfao, J.J.M.; Cunha, A.F. [Laboratorio de Catalise e Materiais, Laboratorio Associado LSRE/LCM, Departamento de Engenharia Quimica, Faculdade de Engenharia, Universidade do Porto, Rua Dr. Roberto Frias, 4200-465 Porto (Portugal)

    2010-09-15

    The catalytic decomposition of methane into hydrogen and carbon was studied on La{sub 2}O{sub 3} doped Ni and Ni-Cu Raney-type catalysts. The activity and stability of the catalysts were assessed by comparing the experimental conversions with the calculated equilibrium conversions for each set of experimental conditions, and the maximum conversions with the conversions at the end of (at least) 5 h tests, respectively. Improved stability of La{sub 2}O{sub 3} doped catalysts was ascribed to an electronic promotion effect. There is an optimum load of the promoter, which provides for extended periods of stable catalyst operation. The carbon deposits consist of carbon nanofibers and multiwall carbon nanotubes. The La{sub 2}O{sub 3} doped Ni-Cu Raney-type catalysts presented in this work are remarkably efficient for the production of hydrogen by methane decomposition. (author)

  3. A novel biological hydrogen production system. Impact of organic loading

    Energy Technology Data Exchange (ETDEWEB)

    Hafez, Hisham; Nakhla, George; El Naggar, Hesham [Western Ontario Univ. (Canada)

    2010-07-01

    The patent-pending system comprises a novel biohydrogen reactor with a gravity settler for decoupling of SRT from HRT. Two biohydrogenators were operated for 220 days at 37 C, hydraulic retention time 8 h and solids retention time ranged from 1.4 to 2 days under four different glucose concentrations of 2, 8, 16, 32, 48 and 64 g/L, corresponding to organic loading rates of 6.5-206 kg COD/m{sup 3}-d, and started up using anaerobically-digested sludge from the St. Marys wastewater treatment plant (St.Mary, Ontario, Canada) as the seed. The system steadily produced hydrogen with no methane. A maximum hydrogen yield of 3.1 mol H{sub 2} /mol glucose was achieved in the system for all the organic loading rates with an average of 2.8mol H{sub 2} /mol glucose. Acetate and butyrate were the main effluent liquid products at concentrations ranging from 640-7400 mg/L and 400-4600 mg/l, respectively, with no lactate detection. Microbial community analysis using denaturing gradient gel electrophoresis (DGGE) confirmed the absence of lactate producing bacteria Lactobacillus fermentum and other non-hydrogen producing species, and the predominance of various Clostridium species. Biomass concentrations in the biohydrogenators were steady, during the runs, varying form 1500 mg/L at the OLR of 6.5 kg COD/m{sup 3}-d to 14000 mg/L at the 104 kg COD/m{sup 3}-d, thus emphasizing the potential of this novel system for sustained stable hydrogen production and prevention of biomass washout. (orig.)

  4. Tensile plastic strain localization in single crystals of austenite steel electrolytically saturated with hydrogen

    Science.gov (United States)

    Barannikova, S. A.; Nadezhkin, M. V.; Mel'Nichuk, V. A.; Zuev, L. B.

    2011-09-01

    The effect of interstitial hydrogen atoms on the mechanical properties and plastic strain localization patterns in tensile tested Fe-18Cr-12Ni-2Mo single crystals of austenite steel with low stacking-fault energy has been studied using a double-exposure speckle photography technique. The main parameters of plastic-flow localization at various stages of the deformation hardening of crystals have been determined in single crystals of steel electrolytically saturated with hydrogen in a three-electrode electrochemical cell at a controlled constant cathode potential.

  5. Hydrogen from renewable energy: A pilot plant for thermal production and mobility

    Science.gov (United States)

    Degiorgis, L.; Santarelli, M.; Calì, M.

    In the mainframe of a research contract, a feasibility pre-design study of a hydrogen-fuelled Laboratory-Village has been carried out: the goals are the design and the simulation of a demonstration plant based on hydrogen as primary fuel. The hydrogen is produced by electrolysis, from electric power produced by a mix of hydroelectric and solar photovoltaic plants. The plant will be located in a small remote village in Valle d'Aosta (Italy). This country has large water availability from glaciers and mountains, so electricity production from fluent water hydroelectric plants is abundant and cheap. Therefore, the production of hydrogen during the night (instead of selling the electricity to the grid at very low prices) could become a good economic choice, and hydrogen could be a competitive local fuel in term of costs, if compared to oil or gas. The H 2 will be produced and stored, and used to feed a hydrogen vehicle and for thermal purposes (heating requirement of three buildings), allowing a real field test (Village-Laboratory). Due to the high level of pressure requested for H 2 storage on-board in the vehicle, the choice has been the experimental test of a prototype laboratory-scale high-pressure PEM electrolyzer: a test laboratory has been designed, to investigate the energy savings related to this technology. In the paper, the description of the dynamic simulation of the plant (developed with TRNSYS) together with a detailed design and an economic analysis (proving the technical and economical feasibility of the installation) has been carried out. Moreover, the design of the high-pressure PEM electrolyzer is described.

  6. Maximizing renewable hydrogen production from biomass in a bio/catalytic refinery

    DEFF Research Database (Denmark)

    Westermann, Peter; Jørgensen, Betina; Lange, L.;

    2007-01-01

    Biological production of hydrogen from biomass by fermentative or photofermentative microorganisms has been described in numerous research articles and reviews. The major challenge of these techniques is the low yield from fermentative production, and the large reactor volumes necessary...... for photofermentative production. Due to these constraints biological hydrogen production from biomass has so far not been considered a significant source in most scenarios of a future hydrogen-based economy. In this review we briefly summarize the current state of art of biomass-based hydrogen production and suggest...... a combination of a biorefinery for the production of multiple fuels (hydrogen, ethanol, and methane) and chemical catalytic technologies which could lead to a yield of 10-12 mol hydrogen per mol glucose derived from biological waste products. Besides the high hydrogen yield, the advantage of the suggested...

  7. Hydrogen

    Directory of Open Access Journals (Sweden)

    John O’M. Bockris

    2011-11-01

    Full Text Available The idea of a “Hydrogen Economy” is that carbon containing fuels should be replaced by hydrogen, thus eliminating air pollution and growth of CO2 in the atmosphere. However, storage of a gas, its transport and reconversion to electricity doubles the cost of H2 from the electrolyzer. Methanol made with CO2 from the atmosphere is a zero carbon fuel created from inexhaustible components from the atmosphere. Extensive work on the splitting of water by bacteria shows that if wastes are used as the origin of feed for certain bacteria, the cost for hydrogen becomes lower than any yet known. The first creation of hydrogen and electricity from light was carried out in 1976 by Ohashi et al. at Flinders University in Australia. Improvements in knowledge of the structure of the semiconductor-solution system used in a solar breakdown of water has led to the discovery of surface states which take part in giving rise to hydrogen (Khan. Photoelectrocatalysis made a ten times increase in the efficiency of the photo production of hydrogen from water. The use of two electrode cells; p and n semiconductors respectively, was first introduced by Uosaki in 1978. Most photoanodes decompose during the photoelectrolysis. To avoid this, it has been necessary to create a transparent shield between the semiconductor and its electronic properties and the solution. In this way, 8.5% at 25 °C and 9.5% at 50 °C has been reached in the photo dissociation of water (GaP and InAs by Kainthla and Barbara Zeleney in 1989. A large consortium has been funded by the US government at the California Institute of Technology under the direction of Nathan Lewis. The decomposition of water by light is the main aim of this group. Whether light will be the origin of the post fossil fuel supply of energy may be questionable, but the maximum program in this direction is likely to come from Cal. Tech.

  8. Product selectivity in plasmonic photocatalysis for carbon dioxide hydrogenation

    Science.gov (United States)

    Zhang, Xiao; Li, Xueqian; Zhang, Du; Su, Neil Qiang; Yang, Weitao; Everitt, Henry O.; Liu, Jie

    2017-01-01

    Photocatalysis has not found widespread industrial adoption, in spite of decades of active research, because the challenges associated with catalyst illumination and turnover outweigh the touted advantages of replacing heat with light. A demonstration that light can control product selectivity in complex chemical reactions could prove to be transformative. Here, we show how the recently demonstrated plasmonic behaviour of rhodium nanoparticles profoundly improves their already excellent catalytic properties by simultaneously reducing the activation energy and selectively producing a desired but kinetically unfavourable product for the important carbon dioxide hydrogenation reaction. Methane is almost exclusively produced when rhodium nanoparticles are mildly illuminated as hot electrons are injected into the anti-bonding orbital of a critical intermediate, while carbon monoxide and methane are equally produced without illumination. The reduced activation energy and super-linear dependence on light intensity cause the unheated photocatalytic methane production rate to exceed the thermocatalytic rate at 350 °C. PMID:28230100

  9. Hydrogen production from methane through catalytic partial oxidation reactions

    Science.gov (United States)

    Freni, S.; Calogero, G.; Cavallaro, S.

    This paper reviews recent developments in syn-gas production processes used for partial methane oxidation with and/or without steam. In particular, we examined different process charts (fixed bed, fluidised bed, membrane, etc.), kinds of catalysts (powders, foams, monoliths, etc.) and catalytically active phases (Ni, Pt, Rh, etc.). The explanation of the various suggested technical solutions accounted for the reaction mechanism that may selectively lead to calibrated mixtures of CO and H 2 or to the unwanted formation of products of total oxidation (CO 2 and H 2O) and pyrolysis (coke). Moreover, the new classes of catalysts allow the use of small reactors to treat large amounts of methane (monoliths) or separate hydrogen in situ from the other reaction products (membrane). This leads to higher conversions and selectivity than could have been expected thermodynamically. Although catalysts based on Rh are extremely expensive, they can be used to minimise H 2O formation by maximising H 2 yield.

  10. Hydrogen production by coal plasma gasification for fuel cell technology

    Energy Technology Data Exchange (ETDEWEB)

    Galvita, V. [Max-Planck-Institute, Dynamics of Complex Technical Systems, Sandtorstrasse 1, 39106, Magdeburg (Germany); Messerle, V.E.; Ustimenko, A.B. [Research Department of Plasmotechnics, 22 Zvereva str., 050100 Almaty (Kazakhstan)

    2007-11-15

    Coal gasification in steam and air atmosphere under arc plasma conditions has been investigated with Podmoskovnyi brown coal, Kuuchekinski bituminous coal and Canadian petrocoke. It was found that for those coals the gasification degree to synthesis gas were 92.3%, 95.8 and 78.6% correspondingly. The amount of produced syngas was 30-40% higher in steam than in air gasification of the coal. The reduction of the carbon monoxide content in the hydrogen-rich reformate gas for low-temperature fuel cell applications normally involves high- and low-temperature water gas shift reactors followed by selective oxidation of residual carbon monoxide. It is shown that the carbon monoxide content can be reduced in one single reactor, which is based on an iron redox cycle. During the reduction phase of the cycle, the raw gas mixture of H{sub 2} and CO reduces a Fe{sub 3}O{sub 4}-CeO{sub 2}-ZrO{sub 2} sample, while during the oxidation phase steam re-oxidizes the iron and simultaneously hydrogen is being produced. The integration of the redox iron process with a coal plasma gasification technology in future allows the production of CO{sub x}-free hydrogen. (author)

  11. Hydrogen production from high moisture content biomass in supercritical water

    Energy Technology Data Exchange (ETDEWEB)

    Antal, M.J. Jr.; Xu, X. [Univ. of Hawaii, Honolulu, HI (United States). Hawaii Natural Energy Inst.

    1998-08-01

    By mixing wood sawdust with a corn starch gel, a viscous paste can be produced that is easily delivered to a supercritical flow reactor by means of a cement pump. Mixtures of about 10 wt% wood sawdust with 3.65 wt% starch are employed in this work, which the authors estimate to cost about $0.043 per lb. Significant reductions in feed cost can be achieved by increasing the wood sawdust loading, but such an increase may require a more complex pump. When this feed is rapidly heated in a tubular flow reactor at pressures above the critical pressure of water (22 MPa), the sawdust paste vaporizes without the formation of char. A packed bed of carbon catalyst in the reactor operating at about 650 C causes the tarry vapors to react with water, producing hydrogen, carbon dioxide, and some methane with a trace of carbon monoxide. The temperature and history of the reactor`s wall influence the hydrogen-methane product equilibrium by catalyzing the methane steam reforming reaction. The water effluent from the reactor is clean. Other biomass feedstocks, such as the waste product of biodiesel production, behave similarly. Unfortunately, sewage sludge does not evidence favorable gasification characteristics and is not a promising feedstock for supercritical water gasification.

  12. Developments of Catalysts for Hydrogen Production from Dimethyl Ether

    Institute of Scientific and Technical Information of China (English)

    Kaoru; Takeishi

    2007-01-01

    1 Results Dimethyl ether (DME) is expected as a clean fuel of the 21st century.I have developed new catalysts for hydrogen production by steam reforming of DME.Cu-Zn/Al2O3 catalysts prepared by the sol-gel method produce large quantities of H2 and CO2 by DME steam reforming under lower reaction temperature[1].However,the sol-gel catalysts will be more expensive than general catalysts prepared by impregnation methods and coprecipitation methods,because the precursor,alkoxides are very expensive.For pract...

  13. Dispatchable Hydrogen Production at the Forecourt for Electricity Demand Shaping

    Directory of Open Access Journals (Sweden)

    Abdulla Rahil

    2017-10-01

    Full Text Available Environmental issues and concerns about depletion of fossil fuels have driven rapid growth in the generation of renewable energy (RE and its use in electricity grids. Similarly, the need for an alternative to hydrocarbon fuels means that the number of fuel cell vehicles is also expected to increase. The ability of electricity networks to balance supply and demand is greatly affected by the variable, intermittent output of RE generators; however, this could be relieved using energy storage and demand-side response (DSR techniques. One option would be production of hydrogen by electrolysis powered from wind and solar sources. The use of tariff structures would provide an incentive to operate electrolysers as dispatchable loads. The aim of this paper is to compare the cost of hydrogen production by electrolysis at garage forecourts in Libya, for both dispatchable and continuous operation, without interruption of fuel supply to vehicles. The coastal city of Derna was chosen as a case study, with the renewable energy being produced via a wind turbine farm. Wind speed was analysed in order to determine a suitable turbine, then the capacity was calculated to estimate how many turbines would be needed to meet demand. Finally, the excess power was calculated, based on the discrepancy between supply and demand. The study looked at a hydrogen refueling station in both dispatchable and continuous operation, using an optimisation algorithm. The following three scenarios were considered to determine whether the cost of electrolytic hydrogen could be reduced by a lower off-peak electricity price. These scenarios are: Standard Continuous, in which the electrolyser operates continuously on a standard tariff of 12 p/kWh; Off-peak Only, in which the electrolyser operates only during off-peak periods at the lower price of 5 p/kWh; and 2-Tier Continuous, in which the electrolyser operates continuously on a low tariff at off-peak times and a high tariff at other

  14. Hydrogen production from banyan leaves using an atmospheric-pressure microwave plasma reactor.

    Science.gov (United States)

    Lin, Yuan-Chung; Wu, Tzi-Yi; Jhang, Syu-Ruei; Yang, Po-Ming; Hsiao, Yi-Hsing

    2014-06-01

    Growth of the hydrogen market has motivated increased study of hydrogen production. Understanding how biomass is converted to hydrogen gas can help in evaluating opportunities for reducing the environmental impact of petroleum-based fuels. The microwave power used in the reaction is found to be proportional to the rate of production of hydrogen gas, mass of hydrogen gas produced per gram of banyan leaves consumed, and amount of hydrogen gas formed with respect to the H-atom content of banyan leaves decomposed. Increase the microwave power levels results in an increase of H2 and decrease of CO2 concentrations in the gaseous products. This finding may possibly be ascribed to the water-gas shift reaction. These results will help to expand our knowledge concerning banyan leaves and hydrogen yield on the basis of microwave-assisted pyrolysis, which will improve the design of hydrogen production technologies.

  15. Hydrogen production by hyperthermophilic and extremely thermophilic bacteria and archaea: mechanisms for reductant disposal

    NARCIS (Netherlands)

    Verhaart, M.R.A.; Bielen, A.A.M.; Oost, van der J.; Stams, A.J.M.; Kengen, S.W.M.

    2010-01-01

    Hydrogen produced from biomass by bacteria and archaea is an attractive renewable energy source. However, to make its application more feasible, microorganisms are needed with high hydrogen productivities. For several reasons, hyperthermophilic and extremely thermophilic bacteria and archaea are pro

  16. Maximum hydrogen production from genetically modified microalgae biomass

    Science.gov (United States)

    Vargas, Jose; Kava, Vanessa; Ordonez, Juan

    A transient mathematical model for managing microalgae derived H2 production as a source of renewable energy is developed for a well stirred photobioreactor, PBR. The model allows for the determination of microalgae and H2 mass fractions produced by the PBR in time. A Michaelis-Menten expression is proposed for modeling the rate of H2 production, which introduces an expression to calculate the resulting effect on H2 production rate after genetically modifying the microalgae. The indirect biophotolysis process was used. Therefore, an opportunity was found to optimize the aerobic to anaerobic stages time ratio of the cycle for maximum H2 production rate, i.e., the process rhythm. A system thermodynamic optimization is conducted with the model equations to find accurately the optimal system operating rhythm for maximum H2 production rate, and how wild and genetically modified species compare to each other. The maxima found are sharp, showing up to a ~60% variation in hydrogen production rate within 2 days around the optimal rhythm, which highlights the importance of system operation in such condition. Therefore, the model is expected to be useful for design, control and optimization of H2 production. Brazilian National Council of Scientific and Technological Development, CNPq (project 482336/2012-9).

  17. Water dynamics: relation between hydrogen bond bifurcations, molecular jumps, local density & hydrophobicity.

    Science.gov (United States)

    Titantah, John Tatini; Karttunen, Mikko

    2013-10-21

    Structure and dynamics of water remain a challenge. Resolving the properties of hydrogen bonding lies at the heart of this puzzle. We employ ab initio Molecular Dynamics (AIMD) simulations over a wide temperature range. The total simulation time was ≈ 2 ns. Both bulk water and water in the presence of a small hydrophobic molecule were simulated. We show that large-angle jumps and bond bifurcations are fundamental properties of water dynamics and that they are intimately coupled to both local density and hydrogen bond strength oscillations in scales from about 60 to a few hundred femtoseconds: Local density differences are the driving force for bond bifurcations and the consequent large-angle jumps. The jumps are intimately connected to the recently predicted hydrogen bond energy asymmetry. Our analysis also appears to confirm the existence of the so-called negativity track provided by the lone pairs of electrons on the oxygen atom to enable water rotation.

  18. [Isolation of a high hydrogen-producing mutant TB34 generated by transposon insertion and analysis of hydrogen production].

    Science.gov (United States)

    Liu, Hong-Yan; Wang, Guang-Ce; Shi, Liu-Yang; Zhu, Da-Ling

    2012-07-01

    To increase the hydrogen-producing capacity of Pantoea agglomerans BH18, isolated from mangrove sludge, we constructed a stable transposon mutagenesis library of this strain. A Tn7-based transposon was randomly inserted into the genomic DNA. Mutants were screened by kanamycin resistance and identified by amplification of the inserted transposon sequences. A mutant strain TB34 was isolated, whose hydrogen production capacity was significantly improved compared to the wild type strain. In seawater-containing medium supplemented with 10 g x L(-1) glucose and had an initial pH of 7.0, the hydrogen yield (H2/glucose) of the mutant strain was (2.04 +/- 0.04) mol x mol(-1), which was 43% higher than that of the wild type strain. The mutant TB34 showed steady hydrogen production capacity for five consecutive passages. Different carbon sources were tested in the hydrogen production by the mutant TB34 and the results showed that both the mutant strain TB34 and the wild type strain BH18 were able to produce hydrogen on sucrose, glucose and fructose. However, different from the wild type strain, the mutant strain TB34 was also able to produce hydrogen using xylose as substrate, with a hydrogen yield (H2/xylose) of (1.34 +/- 0.09) mol x mol(-1), indicating a broader substrate spectrum in the mutant.

  19. Regularities in localization of plastic flow upon electrolytic hydrogenation of an iron bcc-alloy

    Science.gov (United States)

    Barannikova, S. A.; Nadezhkin, M. V.; Lunev, A. G.; Gorbatenko, V. V.; Zuev, L. B.

    2014-03-01

    The impact of implanted hydrogen atoms on mechanical properties and characteristics of plastic-flow localization upon tensile stresses of the polycrystalline Fe-0.07 wt % C alloy is studied. Using the method of double-exposure speckle photography, we identified the main types and parameters of plastic-flow localization at different stages of strain hardening as a result of electrolytic saturation in a three-electrode electrochemical cell at a constant controlled cathodic potential.

  20. Solid State Materials for Hydrogen Production, Ionic Conduction and Oxygen Reduction

    OpenAIRE

    MAO, CHENGYU

    2016-01-01

    Fuel cells convert chemical energy directly into electricity with high efficiency and low pollutant emission via redox reactions at the anode and cathode. The implementation of hydrogen fuel cell depends on the large scale production of hydrogen. Though ‘’hydrogen economy” scenario looks attractive, a breakthrough in hydrogen production. An efficient fuel cell is also dependent on a good ionic conductor between the electrodes and good electrocatalysts for oxygen reduction reactions. Artificia...

  1. Proposed principles of maximum local entropy production.

    Science.gov (United States)

    Ross, John; Corlan, Alexandru D; Müller, Stefan C

    2012-07-12

    Articles have appeared that rely on the application of some form of "maximum local entropy production principle" (MEPP). This is usually an optimization principle that is supposed to compensate for the lack of structural information and measurements about complex systems, even systems as complex and as little characterized as the whole biosphere or the atmosphere of the Earth or even of less known bodies in the solar system. We select a number of claims from a few well-known papers that advocate this principle and we show that they are in error with the help of simple examples of well-known chemical and physical systems. These erroneous interpretations can be attributed to ignoring well-established and verified theoretical results such as (1) entropy does not necessarily increase in nonisolated systems, such as "local" subsystems; (2) macroscopic systems, as described by classical physics, are in general intrinsically deterministic-there are no "choices" in their evolution to be selected by using supplementary principles; (3) macroscopic deterministic systems are predictable to the extent to which their state and structure is sufficiently well-known; usually they are not sufficiently known, and probabilistic methods need to be employed for their prediction; and (4) there is no causal relationship between the thermodynamic constraints and the kinetics of reaction systems. In conclusion, any predictions based on MEPP-like principles should not be considered scientifically founded.

  2. Complete genome sequence of Enterobacter sp. IIT-BT 08: A potential microbial strain for high rate hydrogen production.

    Science.gov (United States)

    Khanna, Namita; Ghosh, Ananta Kumar; Huntemann, Marcel; Deshpande, Shweta; Han, James; Chen, Amy; Kyrpides, Nikos; Mavrommatis, Kostas; Szeto, Ernest; Markowitz, Victor; Ivanova, Natalia; Pagani, Ioanna; Pati, Amrita; Pitluck, Sam; Nolan, Matt; Woyke, Tanja; Teshima, Hazuki; Chertkov, Olga; Daligault, Hajnalka; Davenport, Karen; Gu, Wei; Munk, Christine; Zhang, Xiaojing; Bruce, David; Detter, Chris; Xu, Yan; Quintana, Beverly; Reitenga, Krista; Kunde, Yulia; Green, Lance; Erkkila, Tracy; Han, Cliff; Brambilla, Evelyne-Marie; Lang, Elke; Klenk, Hans-Peter; Goodwin, Lynne; Chain, Patrick; Das, Debabrata

    2013-12-20

    Enterobacter sp. IIT-BT 08 belongs to Phylum: Proteobacteria, Class: Gammaproteobacteria, Order: Enterobacteriales, Family: Enterobacteriaceae. The organism was isolated from the leaves of a local plant near the Kharagpur railway station, Kharagpur, West Bengal, India. It has been extensively studied for fermentative hydrogen production because of its high hydrogen yield. For further enhancement of hydrogen production by strain development, complete genome sequence analysis was carried out. Sequence analysis revealed that the genome was linear, 4.67 Mbp long and had a GC content of 56.01%. The genome properties encode 4,393 protein-coding and 179 RNA genes. Additionally, a putative pathway of hydrogen production was suggested based on the presence of formate hydrogen lyase complex and other related genes identified in the genome. Thus, in the present study we describe the specific properties of the organism and the generation, annotation and analysis of its genome sequence as well as discuss the putative pathway of hydrogen production by this organism.

  3. ENHANCED HYDROGEN ECONOMICS VIA COPRODUCTION OF FUELS AND CARBON PRODUCTS

    Energy Technology Data Exchange (ETDEWEB)

    Kennel, Elliot B; Bhagavatula, Abhijit; Dadyburjor, Dady; Dixit, Santhoshi; Garlapalli, Ravinder; Magean, Liviu; Mukkha, Mayuri; Olajide, Olufemi A; Stiller, Alfred H; Yurchick, Christopher L

    2011-03-31

    This Department of Energy National Energy Technology Laboratory sponsored research effort to develop environmentally cleaner projects as a spin-off of the FutureGen project, which seeks to reduce or eliminate emissions from plants that utilize coal for power or hydrogen production. New clean coal conversion processes were designed and tested for coproducing clean pitches and cokes used in the metals industry as well as a heavy crude oil. These new processes were based on direct liquefaction and pyrolysis techniques that liberate volatile liquids from coal without the need for high pressure or on-site gaseous hydrogen. As a result of the research, a commercial scale plant for the production of synthetic foundry coke has broken ground near Wise, Virginia under the auspices of Carbonite Inc. This plant will produce foundry coke by pyrolyzing a blend of steam coal feedstocks. A second plant is planned by Quantex Energy Inc (in Texas) which will use solvent extraction to coproduce a coke residue as well as crude oil. A third plant is being actively considered for Kingsport, Tennessee, pending a favorable resolution of regulatory issues.

  4. Bioelectrochemical hydrogen production from urban wastewater on a pilot scale

    Science.gov (United States)

    Baeza, Juan A.; Martínez-Miró, Àlex; Guerrero, Javier; Ruiz, Yolanda; Guisasola, Albert

    2017-07-01

    Bioelectrochemical hydrogen production has been successfully achieved in laboratory-scale conditions with different substrates. However, scaling up microbial electrolysis cells (MECs) is not straightforward, and reported attempts have not been completely successful. This work presents the design, building, start-up and operation of an MEC pilot plant (130 L) based on a cassette configuration. The plant was started up in batch mode with acetate and glucose as substrates and operated for five months with different substrates (i.e. glucose, diluted raw glycerol and real urban wastewater). The best results were obtained in the last period with primary effluent from real urban wastewater. The hydrogen production increased to values higher than 4 L d-1 with a gas purity of 95%, a cathodic gas recovery of 82% and an energy recovery of 121% with respect to the electrical input. The organic matter removal efficiency was approximately 25% for a hydraulic retention time of 2 d with an organic loading rate (OLR) of 0.25 gCOD·L-1·d-1. It should be possible to achieve removal efficiencies around 75% with OLRs lower than 0.05 gCOD·L-1·d-1. These results are promising and represent an important step towards the industrial implementation of these systems.

  5. Development and Improvement of Bioreactor for Fermentative Hydrogen Production

    Institute of Scientific and Technical Information of China (English)

    LI Yong-feng; REN Nan-qi; YANG Chuan-ping; DING Jie; LI Jian-zheng

    2006-01-01

    The paper reviewed hydrogen production biotechnology on reactor development and design aspects. Biological hydrogen-producing reactor as acid-producing phase of two-phase anaerobic organism treatment system plays an important role in the following aspects: Reactor was developed as the follow ideas: 1) CSTR-type anaerobic fermentation reactor is selected to reduce the substrate concentration in reactor and increase target product operational yield and selectivity in the reactor;2)Integration structure with mixing reaction area and deposit-separating area is selected, i.e. gas-liquid-solid phase separation unit; 3)Mixture liquid in reaction area is stirred by the stirrer to reach a turbulent state in order to reduce interfacial layer thickness and temperature gradient in a floc unit particle and increase mass transfer rate;4) H2 in the particle and liquid phase is accelerated to release to prevent accumulated H2 from bringing feedback inhibition to organism metabolism, and H2/CO2conversion to acetic acid; 5) A sector turbine agitator with hoisting capacity and mixing power is selected to facilitate sludge to flow back through a effluence seam; 6 ) Interior wall in the reaction area is equipped with vertical baffles to avoid causing swirling flow of mixture liquid owing to agitation.

  6. Cobaloxime-based photo-catalytic devices for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Fihri, A.; Artero, V.; Razavet, M.; Baffert, C.; Fontecave, M. [CEA Grenoble, DSV, iRTSV, Lab Chim et Biol Metaux, CNRS, UMR 5249, Univ Grenoble 1, F-38054 Grenoble 9 (France); Leibl, W. [CEA, DSV, iBiTecS, Lab Photocatalyse et Biohydrogene, CNRS, URA 2096, Gif Sur Yvette (France)

    2008-07-01

    In this paper is described the synthesis and activity of a series of novel hetero-dinuclear ruthenium-cobaloxime photo-catalysts able to achieve the photochemical production of hydrogen with the highest turnover numbers so far reported for such devices. First of all, substituting cobalt for rare and expensive platinum, palladium, or rhodium metals in photo-catalysts is a first step toward economically viable hydrogen production. Cobaloximes appear to be good candidates for H{sub 2}-evolving catalysts, and they may provide a good basis for the design of photo-catalysts that function in pure water as both the solvent and the sustainable proton source. Secondly, a molecular connection between the sensitizer and the H{sub 2}-evolving catalyst seems to provide advantages regarding the photo-catalytic activity. Structural modifications of this connection should allow a better tuning of the electron transfer between the light-harvesting unit and the catalytic center and thus an increase of the efficiency of the system. (O.M.)

  7. Suppression of methanogenesis for hydrogen production in single-chamber microbial electrolysis cells using various antibiotics.

    Science.gov (United States)

    Catal, Tunc; Lesnik, Keaton Larson; Liu, Hong

    2015-01-01

    Methanogens can utilize the hydrogen produced in microbial electrolysis cells (MECs), thereby decreasing the hydrogen generation efficiency. However, various antibiotics have previously been shown to inhibit methanogenesis. In the present study antibiotics, including neomycin sulfate, 2-bromoethane sulfonate, 2-chloroethane sulfonate, 8-aza-hypoxanthine, were examined to determine if hydrogen production could be improved through inhibition of methanogenesis but not hydrogen production in MECs. 1.1mM neomycin sulfate inhibited both methane and hydrogen production while 2-chloroethane sulfonate (20mM), 2-bromoethane sulfonate (20mM), and 8-aza-hypoxanthine (3.6mM) can inhibited methane generation and with concurrent increases in hydrogen production. Our results indicated that adding select antibiotics to the mixed species community in MECs could be a suitable method to enhance hydrogen production efficiency.

  8. Thermophysical properties and modeling of a hydrogenic pellet production system

    Science.gov (United States)

    Leachman, Jacob William

    A fusion energy experiment that is under construction, the ITER machine, has the mission to be the first device to demonstrate the technological feasibility of fusion energy and serve as the primary step towards commercialization of fusion reactors. The ITER machine and future fusion energy machines will require a continuous supply of hydrogenic fuel pellets for sustained operation. The purpose of this research is to provide the fundamental visco-plastic flow measurements as well as the numerical models that are necessary to design a hydrogenic pellet production system (PPS) to meet the ITER fueling specifications. A numerical model of a PPS for the ITER machine is presented and used to design a system that precools, liquefies, and solidifies hydrogenic material that is ultimately extruded and cut into fuel pellets. The specific components modeled within the PPS include a precooling heat exchanger, a liquefier, and a twin-screw solidifying extruder. Numerical models of these components are developed and used as design tools. The modeling results suggest that the performance of the PPS will be dictated by the heat transfer and viscous dissipation associated with the solid and solidifying hydrogen in the twin-screw extruder. This observation motivates experimental efforts that are aimed at precise measurement of these quantities. Steady-state measurements are presented of the dynamic shear stress and heat transfer during flow of solid hydrogen, deuterium, and neon in a Couette type viscometer cell. Thermal conductivity measurements in the stationary condition are compared with those reported in the literature. The measurements span a range of shear rates and extend from temperatures associated with the onset of solidification to sub-cooled solid states. The viscous dissipation is found to vary directly with the applied heat load from the onset of solidification to the point at which the solid begins to sub-cool. Flow of the sub-cooled solid exhibits behavior that is

  9. Effects of carbohydrate, protein and lipid content of organic waste on hydrogen production and fermentation products.

    Science.gov (United States)

    Alibardi, Luca; Cossu, Raffaello

    2016-01-01

    Organic waste from municipalities, food waste and agro-industrial residues are ideal feedstocks for use in biological conversion processes in biorefinery chains, representing biodegradable materials containing a series of substances belonging to the three main groups of the organic matter: carbohydrates, proteins and lipids. Biological hydrogen production by dark fermentation may assume a central role in the biorefinery concept, representing an up-front treatment for organic waste capable of hydrolysing complex organics and producing biohydrogen. This research study was aimed at evaluating the effects of carbohydrate, protein and lipid content of organic waste on hydrogen yields, volatile fatty acid production and carbon-fate. Biogas and hydrogen productions were linearly correlated to carbohydrate content of substrates while proteins and lipids failed to produce significant contributions. Chemical composition also produced effects on the final products of dark fermentation. Acetic and butyric acids were the main fermentation products, with their ratio proving to correlate with carbohydrate and protein content. The results obtained in this research study enhance the understanding of data variability on hydrogen yields from organic waste. Detailed information on waste composition and chemical characterisation are essential to clearly identify the potential performances of the dark fermentation process.

  10. Simulation of a porous ceramic membrane reactor for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Yu, W.; Ohmori, T.; Yamamoto, T.; Endo, A.; Nakaiwa, M.; Hayakawa, T. [National Inst. of Advanced Industrial Science and Technology, Tsukuba (Japan); Itoh, N. [National Inst. of Advanced Industrial Science and Technology, Tsukuba (Japan); Utsunomiya Univ. (Japan). Dept. of Applied Chemistry

    2005-08-01

    A systematic simulation study was performed to investigate the performance of a porous ceramic membrane reactor for hydrogen production by means of methane steam reforming. The results show that the methane conversions much higher than the corresponding equilibrium values can be achieved in the membrane reactor due to the selective removal of products from the reaction zone. The comparison of isothermal and non-isothermal model predictions was made. It was found that the isothermal assumption overestimates the reactor performance and the deviation of calculation results between the two models is subject to the operating conditions. The effects of various process parameters such as the reaction temperature, the reaction side pressure, the feed flow rate and the steam to methane molar feed ratio as well as the sweep gas flow rate and the operation modes, on the behavior of membrane reactor were analyzed and discussed. (author)

  11. Hydrogen Production by Homogeneous Catalysis: Alcohol Acceptorless Dehydrogenation

    DEFF Research Database (Denmark)

    Nielsen, Martin

    2015-01-01

    in hydrogen production from biomass using homogeneous catalysis. Homogeneous catalysis has the advance of generally performing transformations at much milder conditions than traditional heterogeneous catalysis, and hence it constitutes a promising tool for future applications for a sustainable energy sector......, and are fundamental for the thrive of almost all business fields. The latter include the industries of agriculture, food additives, pharmaceuticals, electronics, plastic, fragrances, and more. Today, the major source of both energy and bulk chemicals is fossil fuels, being responsible for more than 80 % of the energy...... dehydrogenation. The third chapter, Biorelevant Substrates, concentrates on the use of alcohols such as ethanol, which are biomass related. The topic is alcohol acceptorless dehydrogenation reactions for both H2 production and the concurrent synthetic application. Finally, Chap. 4, Substrates for H2 Storage...

  12. Sustainable production of green feed from carbon dioxide and hydrogen.

    Science.gov (United States)

    Landau, Miron V; Vidruk, Roxana; Herskowitz, Moti

    2014-03-01

    Carbon dioxide hydrogenation to form hydrocarbons was conducted on two iron-based catalysts, prepared according to procedures described in the literature, and on a new iron spinel catalyst. The CO2 conversion measured in a packed-bed reactor was limited to about 60% because of excessive amounts of water produced in this process. Switching to a system of three packed-bed reactors in series with interim removal of water and condensed hydrocarbons increased CO2 conversion to as much as 89%. The pure spinel catalyst displayed a significantly higher activity and selectivity than those of the other iron catalysts. This process produces a product called green feed, which is similar in composition to the product of a high-temperature, iron-based Fischer–Tropsch process from syngas. The green feed can be readily converted into renewable fuels by well-established technologies.

  13. Thioethers as markers of hydrogen sulfide production in homocystinurias.

    Science.gov (United States)

    Kožich, Viktor; Krijt, Jakub; Sokolová, Jitka; Melenovská, Petra; Ješina, Pavel; Vozdek, Roman; Majtán, Tomáš; Kraus, Jan P

    2016-07-01

    Two enzymes in the transsulfuration pathway of homocysteine -cystathionine beta-synthase (CBS) and gamma-cystathionase (CTH)-use cysteine and/or homocysteine to produce the important signaling molecule hydrogen sulfide (H2S) and simultaneously the thioethers lanthionine, cystathionine or homolanthionine. In this study we explored whether impaired flux of substrates for H2S synthesis and/or deficient enzyme activities alter production of hydrogen sulfide in patients with homocystinurias. As an indirect measure of H2S synthesis we determined by LC-MS/MS concentrations of thioethers in plasma samples from 33 patients with different types of homocystinurias, in 8 patient derived fibroblast cell lines, and as reaction products of seven purified mutant CBS enzymes. Since chaperoned recombinant mutant CBS enzymes retained capacity of H2S synthesis in vitro it can be stipulated that deficient CBS activity in vivo may impair H2S production. Indeed, in patients with classical homocystinuria we observed significantly decreased cystathionine and lanthionine concentrations in plasma (46% and 74% of median control levels, respectively) and significantly lower cystathionine in fibroblasts (8% of median control concentrations) indicating that H2S production from cysteine and homocysteine may be also impaired. In contrast, the grossly elevated plasma levels of homolanthionine in CBS deficient patients (32-times elevation compared to median of controls) clearly demonstrates a simultaneous overproduction of H2S from homocysteine by CTH. In the remethylation defects the accumulation of homocysteine and the increased flux of metabolites through the transsulfuration pathway resulted in elevation of cystathionine and homolanthionine (857% and 400% of median control values, respectively) indicating a possibility of an increased biosynthesis of H2S by both CBS and CTH. This study shows clearly disturbed thioether concentrations in homocystinurias, and modeling using these data indicates

  14. Hydrogen production by aqueous phase reforming of light oxygenated hydrocarbons

    Science.gov (United States)

    Shabaker, John William

    Aqueous phase reforming (APR) of renewable oxygenated hydrocarbons (e.g., methanol, ethylene glycol, glycerol, sorbitol, glucose) is a promising new technology for the catalytic production of high-purity hydrogen for fuel cells and chemical processing. Supported Pt catalysts are effective catalysts for stable and rapid H2 production at temperatures near 500 K (H 2 turnover frequencies near 10 min-1). Inexpensive Raney Ni-based catalysts have been developed using a combination of fundamental and high-throughput studies that have similar catalytic properties as Pt-based materials. Promotion of Raney Ni with Sn by controlled surface reaction of organometallic tin compounds is necessary to control formation of thermodynamically-favorable alkane byproducts. Detailed characterization by Mossbauer spectroscopy, electron microscopy, adsorption studies, and x-ray photoelectron spectroscopy (XPS/ESCA) has shown that NiSn alloys are formed during heat treatment, and may be responsible for enhanced stability and selectivity for hydrogen production. Detailed kinetic studies led to the development of a kinetic mechanism for the APR reaction on Pt and NiSn catalysts, in which the oxygenate decomposes through C--H and O--H cleavage, followed by C--C cleavage and water gas shift of the CO intermediate. The rate limiting step on Pt surfaces is the initial dehydrogenation, while C--C cleavage appears rate limiting over NiSn catalysts. Tin promotion of Raney Ni catalysts suppresses C--O bond scission reactions that lead to alkane formation without inhibiting fast C--C and C--H cleavage steps that are necessary for high rates of reforming. A window of operating temperature, pressure, and reactor residence time has been identified for use of the inexpensive NiSn catalysts as a Pt substitute. Concentrated feed stocks and aggressive pretreatments have been found to counteract catalyst deactivation by sintering in the hydrothermal APR environment and allow stable, long-term production of H

  15. Modeling, Simulation and Optimization of Hydrogen Production Process from Glycerol using Steam Reforming

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jeongpil; Cho, Sunghyun; Kim, Tae-Ok; Shin, Dongil [Myongji University, Yongin (Korea, Republic of); Lee, Seunghwan [JNK Heaters, Seoul (Korea, Republic of); Moon, Dong Ju [Korea Institute of Science and Technology, Seoul (Korea, Republic of)

    2014-12-15

    For improved sustainability of the biorefinery industry, biorefinery-byproduct glycerol is being investigated as an alternate source for hydrogen production. This research designs and optimizes a hydrogen-production process for small hydrogen stations using steam reforming of purified glycerol as the main reaction, replacing existing processes relying on steam methane reforming. Modeling, simulation and optimization using a commercial process simulator are performed for the proposed hydrogen production process from glycerol. The mixture of glycerol and steam are used for making syngas in the reforming process. Then hydrogen are produced from carbon monoxide and steam through the water-gas shift reaction. Finally, hydrogen is separated from carbon dioxide using PSA. This study shows higher yield than former U.S.. DOE and Linde studies. Economic evaluations are performed for optimal planning of constructing domestic hydrogen energy infrastructure based on the proposed glycerol-based hydrogen station.

  16. Kinetic analysis of hydrogen production using anaerobic bacteria in reverse micelles

    Energy Technology Data Exchange (ETDEWEB)

    Zhi, Xiaohua; Yang, Haijun; Yuan, Zhuliang; Shen, Jianquan [Beijing National Laboratory for Molecular Sciences (BNLMS), Laboratory of New Materials, Institute of Chemistry, Chinese Academy of Sciences, Zhongguancun North First Street 2, Beijing 100190 (China)

    2010-04-15

    The micellar formation and entrapment of bacteria cell in reverse micelles were investigated by ultraviolet spectrum (UV), fluorescence spectrum, and scanning electron microscope (SEM). The hydrogen production in reverse micelles was confirmed. The Gompertz equation was employed to evaluate the hydrogen-producing behavior in reverse micellar systems. Different systems including dioctyl sulfosuccinate sodium salt (AOT)-isooctane, sodium dodecyl sulfate (SDS)-benzene and SDS-carbon tetrachloride (CCl{sub 4}) reverse micelles were analysized. The results revealed that the maximum rate of hydrogen production (R{sub m}) was also suitable to formulate the relationship between hydrogen-producing rate and hydrogen productivity in reverse micelles. (author)

  17. Technology status of hydrogen road vehicles. IEA technical report from the IEA Agreement of the production and utilization of hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Doyle, T.A.

    1998-01-31

    The report was commissioned under the Hydrogen Implementing Agreement of the International Energy Agency (IEA) and examines the state of the art in the evolving field of hydrogen-fueled vehicles for road transport. The first phase surveys and analyzes developments since 1989, when a comprehensive review was last published. The report emphasizes the following: problems, especially backfiring, with internal combustion engines (ICEs); operational safety; hydrogen handling and on-board storage; and ongoing demonstration projects. Hydrogen vehicles are receiving much attention, especially at the research and development level. However, there has been a steady move during the past 5 years toward integral demonstrations of operable vehicles intended for public roads. Because they emit few, or no greenhouse gases, hydrogen vehicles are beginning to be taken seriously as a promising solution to the problems of urban air quality. Since the time the first draft of the report was prepared (mid-19 96), the 11th World Hydrogen Energy Conference took place in Stuttgart, Germany. This biennial conference can be regarded as a valid updating of the state of the art; therefore, the 1996 results are included in the current version. Sections of the report include: hydrogen production and distribution to urban users; on-board storage and refilling; vehicle power units and drives, and four appendices titled: 'Safety questions of hydrogen storage and use in vehicles', 'Performance of hydrogen fuel in internal production engines for road vehicles, 'Fuel cells for hydrogen vehicles', and 'Summaries of papers on hydrogen vehicles'. (refs., tabs.)

  18. Chemical Hydride Slurry for Hydrogen Production and Storage

    Energy Technology Data Exchange (ETDEWEB)

    McClaine, Andrew W

    2008-09-30

    The purpose of this project was to investigate and evaluate the attractiveness of using a magnesium chemical hydride slurry as a hydrogen storage, delivery, and production medium for automobiles. To fully evaluate the potential for magnesium hydride slurry to act as a carrier of hydrogen, potential slurry compositions, potential hydrogen release techniques, and the processes (and their costs) that will be used to recycle the byproducts back to a high hydrogen content slurry were evaluated. A 75% MgH2 slurry was demonstrated, which was just short of the 76% goal. This slurry is pumpable and storable for months at a time at room temperature and pressure conditions and it has the consistency of paint. Two techniques were demonstrated for reacting the slurry with water to release hydrogen. The first technique was a continuous mixing process that was tested for several hours at a time and demonstrated operation without external heat addition. Further work will be required to reduce this design to a reliable, robust system. The second technique was a semi-continuous process. It was demonstrated on a 2 kWh scale. This system operated continuously and reliably for hours at a time, including starts and stops. This process could be readily reduced to practice for commercial applications. The processes and costs associated with recycling the byproducts of the water/slurry reaction were also evaluated. This included recovering and recycling the oils of the slurry, reforming the magnesium hydroxide and magnesium oxide byproduct to magnesium metal, hydriding the magnesium metal with hydrogen to form magnesium hydride, and preparing the slurry. We found that the SOM process, under development by Boston University, offers the lowest cost alternative for producing and recycling the slurry. Using the H2A framework, a total cost of production, delivery, and distribution of $4.50/kg of hydrogen delivered or $4.50/gge was determined. Experiments performed at Boston

  19. Fermentative bio-hydrogen production from cellulose by cow dung compost enriched cultures

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Nan-Qi; Xu, Ji-Fei; Gao, Ling-Fang; Xin, Liang; Qiu, Jie; Su, Dong-Xia [State Key Laboratory of Urban Water Resources and Environment, Harbin Institute of Technology, Harbin 150090 (China)

    2010-04-15

    The performance of hydrogen production from cellulose by the cow dung compost enriched continuously in defined medium containing cellulose was investigated. In the initial experiments, batch-fermentation was carried out to observe the effects of different substrate concentration conditions on the rate of cellulose-degrading, growth of bacteria and the capability of hydrogen-producing from cellulose. The result showed that the cellulose degradation decreased from 55% at 5 g/l to 22% at 30 g/l. The maximum cumulative hydrogen production and the rate of hydrogen production first increased from 828 ml/l at 5 g/l to 1251 ml/l at 10 g/l then remained constant beyond 10 g/l. The maximum hydrogen production potential, the rate of hydrogen production and the yield of hydrogen was 1525 ml/l, 33 ml/l.h, and 272 ml/g-cellulose (2.09 mol/mol-hexose) was obtained at substrate concentration 10 g/l, the hydrogen concentration in biogas was 47-50%(v/v) and there was no methane observed. During the conversion of cellulose into hydrogen, acetate and butyrate were main liquid end-products in the metabolism of hydrogen fermentation. These results proposed that cow dung compost enriched cultures were ideal microflora for hydrogen production from cellulose. (author)

  20. Sorption Enhanced Reaction Process (SERP) for production of hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Anand, M.; Hufton, J.; Mayorga, S. [Air Products and Chemicals, Inc., Allentown, PA (United States)] [and others

    1996-10-01

    Sorption Enhanced Reaction Process (SERP) is a novel process that is being developed for the production of lower cost hydrogen by steam-methane reforming (SMR). In this process the reaction of methane with steam is carried out in the presence of an admixture of a catalyst and a selective adsorbent for carbon dioxide. The key consequences of SERP are: (i) reformation reaction is carried out at a significantly lower temperature (300-500{degrees}C) than that in a conventional SMR reactor (800-1100{degrees}C), while achieving the same conversion of methane to hydrogen, (ii) the product hydrogen is obtained at reactor pressure (200-400 psig) and at 98+% purity directly from the reactor (compared to only 70-75% H{sub 2} from conventional SMR reactor), (iii) downstream hydrogen purification step is either eliminated or significantly reduced in size. The first phase of the program has focused on the development of a sorbent for CO{sub 2} which has (a) reversible CO{sub 2} capacity >0.3 mmol/g at low partial pressures of CO{sub 2} (0.1 - 1.0 atm) in the presence of excess steam (pH{sub 2}O/pCO{sub 2}>20) at 400-500{degrees}C and (b) fast sorption-desorption kinetics for CO{sub 2}, at 400-500{degrees}C. Several families of supported sorbents have been identified that meet the target CO{sub 2} capacity. A few of these sorbents have been tested under repeated sorption/desorption cycles and extended exposure to high pressure steam at 400-500{degrees}C. One sorbent has been scaled up to larger quantities (2-3 kg) and tested in the laboratory process equipment for sorption and desorption kinetics of CO{sub 2}. The CO{sub 2}, sorption and desorption kinetics are desirably fast. This was a critical path item for the first phase of the program and now has been successfully demonstrated. A reactor has been designed that will allow nearly isothermal operation for SERP-SMR. This reactor was integrated into an overall process flow diagram for the SERP-SMR process.

  1. PRODUCTIVITY, REPEATABILITY OF PRODUCTIVE AND REPRODUCTIVE TRAITS OF LOCAL PIGEON

    Directory of Open Access Journals (Sweden)

    S. Darwati

    2014-10-01

    Full Text Available The purpose of this study was to know productivity and repeatability of local pigeon. Data werecollected from 124 birds that reared under intensive management. The results showed that artificial pairwas 100% and polygamy was 16% (n=62 pair of pigeon. The ration of local pigeon consisting of 50%corn+50% of commercial feed for starter broiler chicken can be applied in field. The average of eggproduction was 1.8 eggs/pair/period, egg weight was 17.7 g, fertility was 96.6%, hatching rate was 77%,embryo mortality rate was 23%, interval period from laying to hatching and suckling was 51 days, 31.4days with hatching, and 17.6 days without hatching and suckling. The day old pigeon weight ranged10.9-16.2 g. Repeatability value of productive traits was high, in which egg weight was 0.64 and day oldpigeon weight was 0.737. Repeatability of reproductive traits was low, that was fertility and hatchabilitywas 0.12 and 0.048, respectively. The squab weight increased from week 0 to 4, then decreased in theweek 5. The growth rate was highest at the week 1, then decreased from the week 2 to 5 with thenegative growth rate occur at the 5th week. The squab growth rate followed a quadratic pattern. It wasconcluded that slaughter squab selection could be done at 4th week old.

  2. Local atomic structure modulations activate metal oxide as electrocatalyst for hydrogen evolution in acidic water.

    Science.gov (United States)

    Li, Yu Hang; Liu, Peng Fei; Pan, Lin Feng; Wang, Hai Feng; Yang, Zhen Zhong; Zheng, Li Rong; Hu, P; Zhao, Hui Jun; Gu, Lin; Yang, Hua Gui

    2015-08-19

    Modifications of local structure at atomic level could precisely and effectively tune the capacity of materials, enabling enhancement in the catalytic activity. Here we modulate the local atomic structure of a classical but inert transition metal oxide, tungsten trioxide, to be an efficient electrocatalyst for hydrogen evolution in acidic water, which has shown promise as an alternative to platinum. Structural analyses and theoretical calculations together indicate that the origin of the enhanced activity could be attributed to the tailored electronic structure by means of the local atomic structure modulations. We anticipate that suitable structure modulations might be applied on other transition metal oxides to meet the optimal thermodynamic and kinetic requirements, which may pave the way to unlock the potential of other promising candidates as cost-effective electrocatalysts for hydrogen evolution in industry.

  3. Hydrogen production from methane using oxygen-permeable ceramic membranes

    Science.gov (United States)

    Faraji, Sedigheh

    Non-porous ceramic membranes with mixed ionic and electronic conductivity have received significant interest in membrane reactor systems for the conversion of methane and higher hydrocarbons to higher value products like hydrogen. However, hydrogen generation by this method has not yet been commercialized and suffers from low membrane stability, low membrane oxygen flux, high membrane fabrication costs, and high reaction temperature requirements. In this dissertation, hydrogen production from methane on two different types of ceramic membranes (dense SFC and BSCF) has been investigated. The focus of this research was on the effects of different parameters to improve hydrogen production in a membrane reactor. These parameters included operating temperature, type of catalyst, membrane material, membrane thickness, membrane preparation pH, and feed ratio. The role of the membrane in the conversion of methane and the interaction with a Pt/CeZrO2 catalyst has been studied. Pulse studies of reactants and products over physical mixtures of crushed membrane material and catalyst have clearly demonstrated that a synergy exists between the membrane and the catalyst under reaction conditions. The degree of catalyst/membrane interaction strongly impacts the conversion of methane and the catalyst performance. During thermogravimetric analysis, the onset temperature of oxygen release for BSCF was observed to be lower than that for SFC while the amount of oxygen release was significantly greater. Pulse injections of CO2 over crushed membranes at 800°C have shown more CO2 dissociation on the BSCF membrane than the SFC membrane, resulting in higher CO formation on the BSCF membrane. Similar to the CO2 pulses, when CO was injected on the samples at 800°C, CO2 production was higher on BSCF than SFC. It was found that hydrogen consumption on BSCF particles is 24 times higher than that on SFC particles. Furthermore, Raman spectroscopy and temperature programmed desorption studies of

  4. Effect of hydrogen on plastic strain localization and fracture of steels

    Science.gov (United States)

    Nadjozhkin, M. V.; Lunev, A. G.; Li, Yu V.; Barannikova, S. A.

    2016-02-01

    The effect of interstitial hydrogen atoms on the mechanical properties and plastic strain localization patterns in tensile tested specimens of low-carbon steels have been studied using a double exposure speckle photography technique. It is found that the mechanical properties of low-carbon steels are affected adversely by hydrogen embrittlement. The deformation diagrams were examined for the deformed samples of low-carbon steels. These are found to show all the plastic flow stages: the linear, parabolic and pre-failure stages would occur for the respective values of the exponent n from the Ludwik-Holomon equation.

  5. Inhibition of localized corrosion of Ni–Ti superelastic alloy in NaCl solution by hydrogen charging

    Energy Technology Data Exchange (ETDEWEB)

    Yokoyama, Ken’ichi, E-mail: yokken@post.matsc.kyutech.ac.jp [Department of Materials Science and Engineering, Kyushu Institute of Technology, 1-1, Sensui-cho, Tobata-ku, Kitakyushu 804-8550 (Japan); Hirata, Yuki [Department of Materials Science and Engineering, Kyushu Institute of Technology, 1-1, Sensui-cho, Tobata-ku, Kitakyushu 804-8550 (Japan); Inaba, Toshiaki; Mutoh, Kenichiro [Furukawa Techno Material Co., Ltd., 5-1-8, Higashi-yawata, Hiratsuka 254-0016 (Japan); Sakai, Jun’ichi [Faculty of Science and Engineering, Waseda University, 3-4-1, Okubo, Shinjuku-ku, Tokyo 169-8555 (Japan); Kagami Memorial Laboratory for Materials Science and Technology, Waseda University, 2-8-26, Nishiwaseda, Shinjuku-ku, Tokyo 169-0051 (Japan)

    2015-08-05

    Highlights: • Hydrogen charging inhibits localized corrosion of Ni–Ti superelastic alloy. • Increasing hydrogen content increases anodic current density. • Inhibition of localized corrosion remains after polishing or superelastic deformation. • Small amount of hydrogen charging may become new surface modification. - Abstract: Inhibition of the localized corrosion of Ni–Ti superelastic alloy in 0.9% NaCl solution has been attempted by charging with a small amount of hydrogen, which causes negligible hydrogen embrittlement. Upon a small amount of hydrogen charging, no pitting potential is observed in anodic polarization curves. From scanning electron microscope observations, localized corrosion is inhibited on the entire side surface of charged specimens. With increasing amount of charged hydrogen, the corrosion potential shifts in the less noble direction and the current density increases under anodic applied potential. When the hydrogen charged specimens are aged in the atmosphere at room temperature, the corrosion potential becomes almost the same as that of the non-charged specimen, but the inhibition of localized corrosion remains. The present study indicates that a small amount of hydrogen charging is effective for inhibiting the localized corrosion of the alloy in NaCl solution.

  6. Hydrogen production by catalytic gasification of cellulose in supercritical water

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Cellulose,one of the important components of biomass,was gasified in supercritical water to produce hydrogen-rich gas in an autoclave which was operated batch-wise under high-pressure.K2CO3 and Ca(OH)2 were selected as the catalysts (or promoters).The temperature was kept between 450℃ and 500℃ while pressure was maintained at 24-26 MPa.The reaction time was 20 min.Experimental results showed that the two catalysts had good catalytic effect and optimum amounts were observed for each catalyst.When 0.2 g K2CO3 was added,the hydrogen yield could reach 9.456 mol.kg-1 which was two times of the H2 amount produced without catalyst.When 1.6 g Ca(OH)2 was added,the H2 yield was K2CO3 as catalyst but is still 1.7 times that achieved without catalyst.Comparing with the results obtained using KaCO3 or Ca(OH)2 alone,the use of a combination of K2CO3 and Ca(OH)2 could increase the H2 yield by up to 2.5 times that without catalyst and 25% and 45% more than that obtained using K2CO3 and Ca(OH)2 alone,respectively.It was found that methane was the dominant product at relatively low temperature.When the temperature was increased,the methane reacts with water and is converted to hydrogen and carbon dioxide.

  7. Design and construction of a photobioreactor for hydrogen production, including status in the field.

    Science.gov (United States)

    Skjånes, Kari; Andersen, Uno; Heidorn, Thorsten; Borgvang, Stig A

    Several species of microalgae and phototrophic bacteria are able to produce hydrogen under certain conditions. A range of different photobioreactor systems have been used by different research groups for lab-scale hydrogen production experiments, and some few attempts have been made to upscale the hydrogen production process. Even though a photobioreactor system for hydrogen production does require special construction properties (e.g., hydrogen tight, mixing by other means than bubbling with air), only very few attempts have been made to design photobioreactors specifically for the purpose of hydrogen production. We have constructed a flat panel photobioreactor system that can be used in two modes: either for the cultivation of phototrophic microorganisms (upright and bubbling) or for the production of hydrogen or other anaerobic products (mixing by "rocking motion"). Special emphasis has been taken to avoid any hydrogen leakages, both by means of constructional and material choices. The flat plate photobioreactor system is controlled by a custom-built control system that can log and control temperature, pH, and optical density and additionally log the amount of produced gas and dissolved oxygen concentration. This paper summarizes the status in the field of photobioreactors for hydrogen production and describes in detail the design and construction of a purpose-built flat panel photobioreactor system, optimized for hydrogen production in terms of structural functionality, durability, performance, and selection of materials. The motivations for the choices made during the design process and advantages/disadvantages of previous designs are discussed.

  8. High-temperature nuclear reactor power plant cycle for hydrogen and electricity production – numerical analysis

    Directory of Open Access Journals (Sweden)

    Dudek Michał

    2016-01-01

    Full Text Available High temperature gas-cooled nuclear reactor (called HTR or HTGR for both electricity generation and hydrogen production is analysed. The HTR reactor because of the relatively high temperature of coolant could be combined with a steam or gas turbine, as well as with the system for heat delivery for high-temperature hydrogen production. However, the current development of HTR’s allows us to consider achievable working temperature up to 750°C. Due to this fact, industrial-scale hydrogen production using copper-chlorine (Cu-Cl thermochemical cycle is considered and compared with high-temperature electrolysis. Presented calculations show and confirm the potential of HTR’s as a future solution for hydrogen production without CO2 emission. Furthermore, integration of a hightemperature nuclear reactor with a combined cycle for electricity and hydrogen production may reach very high efficiency and could possibly lead to a significant decrease of hydrogen production costs.

  9. High hydrogen production rate of microbial electrolysis cell (MEC) with reduced electrode spacing.

    Science.gov (United States)

    Cheng, Shaoan; Logan, Bruce E

    2011-02-01

    Practical applications of microbial electrolysis cells (MECs) require high hydrogen production rates and a compact reactor. These goals can be achieved by reducing electrode spacing but high surface area anodes are needed. The brush anode MEC with electrode spacing of 2 cm had a higher hydrogen production rate and energy efficiency than an MEC with a flat cathode and a 1-cm electrode spacing. The maximum hydrogen production rate with a 2 cm electrode spacing was 17.8 m(3)/m(3)d at an applied voltage of E(ap)=1 V. Reducing electrode spacing increased hydrogen production rates at the lower applied voltages, but not at the higher (>0.6 V) applied voltages. These results demonstrate that reducing electrode spacing can increase hydrogen production rate, but that the closest electrode spacing do not necessarily produce the highest possible hydrogen production rates.

  10. Durability of solid oxide electrolysis cells for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Hauch, A.; Hoejgaard Jensen, S.; Dalgaard Ebbesen, S.

    2007-05-15

    In the perspective of the increasing interest in renewable energy and hydrogen economy, the reversible solid oxide cells (SOCs) is a promising technology as it has the potential of providing efficient and cost effective hydrogen production by high temperature electrolysis of steam (HTES). Furthermore development of such electrolysis cells can gain from the results obtained within the R and D of SOFCs. For solid oxide electrolysis cells (SOEC) to become interesting from a technological point of view, cells that are reproducible, high performing and long-term stable need to be developed. In this paper we address some of the perspectives of the SOEC technology i.e. issues such as a potential H2 production price as low as 0.71 US dollar/kg H{sub 2} using SOECs for HTES; is there a possible market for the electrolysers? and what R and D steps are needed for the realisation of the SOEC technology? In the experimental part we present electrolysis test results on SOCs that have been optimized for fuel cell operation but applied for HTES. The SOCs are produced on a pre-pilot scale at Risoe National Laboratory. These cells have been shown to have excellent initial electrolysis performance, but the durability of such electrolysis cells are not optimal and examples of results from SOEC tests over several hundreds of hours are given here. The long-term tests have been run at current densities of -0.5 A/cm{sup 2} and -1 A/cm{sup 2}, temperatures of 850 deg. C and 950 deg. C and p(H{sub 2}O)/p(H{sub 2}) of 0.5/0.5 and 0.9/0.1. Long-term degradation rates are shown to be up to 5 times higher for SOECs compared to similar SOFC testing. Furthermore, hydrogen and synthetic fuel production prices are calculated using the experimental results from long-term electrolysis test as input and a short outlook for the future work on SOECs will be given as well. (au)

  11. Rural Tourism and Local Development: Typical Productions of Lazio

    OpenAIRE

    Francesco Maria Olivieri

    2014-01-01

    The local development is based on the integration of the tourism sector with the whole economy. The rural tourism seems to be a good occasion to analyse the local development: consumption of "tourist products" located in specific local contexts. Starting from the food and wine supply chain and the localization of typical productions, the aim of the present work will be analyse the relationship with local development, rural tourism sustainability and accommodation system, referring to Lazio. W...

  12. Hydrogen production by the naked active site of the di-iron hydrogenases in water.

    Science.gov (United States)

    Zipoli, Federico; Car, Roberto; Cohen, Morrel H; Selloni, Annabella

    2009-10-01

    We explored the reactivity of the active center of the [FeFe]-hydrogenases detached from the enzyme and immersed in acidified water by first-principles Car-Parrinello molecular-dynamics simulations. We focused on the identification of the structures that are stable and metastable in acidified water and on their activity for hydrogen production. Our calculations revealed that the naked active center could be an efficient catalyst provided that electrons are transferred to the cluster. We found that both bridging and terminal isomers are present at equilibrium and that the bridging configuration is essential for efficient hydrogen production. The formation of the hydrogen molecule occurs via sequential protonations of the distal iron and of the N-atom of the S-CH(2)-NH-CH(2)-S chelating group. H(2) desorption does not involve a significant energy barrier, making the process very efficient at room temperature. We established that the bottleneck in the reaction is the direct proton transfer from water to the vacant site of the distal iron. Moreover, we found that even if the terminal isomer is present at the equilibrium, its strong local hydrophobicity prevents poisoning of the cluster.

  13. CFD study on hydrogen production during sorption-enhanced glycerol steam reforming

    Directory of Open Access Journals (Sweden)

    M. Ghahremani

    2016-12-01

    Full Text Available This study presents a 2D-axisymmetric computational fluid dynamic (CFD model to investigate the performance of sorption-enhanced during glycerol steam reforming (GSR for hydrogen production. The proposed CFD model provided the local information of velocity, pressure and component concentration for the driving force analysis. After investigation of mesh independency of CFD model, the validation of sorption-enhanced fixed bed reactor during GSR reaction was carried out by experimental data and a good agreement between modeling results and experimental data was achieved. In the present model, a tubular reactor with length of 100 mm was considered, in which the CoNi/Al2O3 as catalyst and CaO as CO2 adsorbent were filled in reaction zone. Hence, the effects of the some important operating parameters (reaction temperature and reaction pressure on the performances of sorption-enhanced fixed bed reactor were studied in terms of glycerol conversion and hydrogen yield. The CFD results showed that the suggested system during GSR reaction presents higher performance with respect to once obtained in the common fixed bed reactor (without CO2 capturing. In particular, in the best operating condition, hydrogen production rate in reaction zone show an enhancement around 12% in the sorption-enhanced fixed bed reactor over once achieved in the common fixed bed reactor.

  14. Challenges and opportunities for hydrogen production from microalgae.

    Science.gov (United States)

    Oey, Melanie; Sawyer, Anne Linda; Ross, Ian Lawrence; Hankamer, Ben

    2016-07-01

    The global population is predicted to increase from ~7.3 billion to over 9 billion people by 2050. Together with rising economic growth, this is forecast to result in a 50% increase in fuel demand, which will have to be met while reducing carbon dioxide (CO2 ) emissions by 50-80% to maintain social, political, energy and climate security. This tension between rising fuel demand and the requirement for rapid global decarbonization highlights the need to fast-track the coordinated development and deployment of efficient cost-effective renewable technologies for the production of CO2 neutral energy. Currently, only 20% of global energy is provided as electricity, while 80% is provided as fuel. Hydrogen (H2 ) is the most advanced CO2 -free fuel and provides a 'common' energy currency as it can be produced via a range of renewable technologies, including photovoltaic (PV), wind, wave and biological systems such as microalgae, to power the next generation of H2 fuel cells. Microalgae production systems for carbon-based fuel (oil and ethanol) are now at the demonstration scale. This review focuses on evaluating the potential of microalgal technologies for the commercial production of solar-driven H2 from water. It summarizes key global technology drivers, the potential and theoretical limits of microalgal H2 production systems, emerging strategies to engineer next-generation systems and how these fit into an evolving H2 economy.

  15. Hydrogen production by autothermal reforming of ethanol: pilot plant

    Energy Technology Data Exchange (ETDEWEB)

    Marin Neto, Antonio Jose; Camargo, Joao Carlos; Lopes, Daniel Gabriel; Ferreira, Paulo F.P. [Hydrogen Technology (HyTron), Campinas, SP (Brazil)], Email: antonio@hytron.com.br; Neves Junior, Newton Pimenta; Pinto, Edgar A. de Godoi Rodrigues; Silva, Ennio Peres da [Universidade Estadual de Campinas (DFA/ IFGW/UNICAMP), SP (Brazil). Inst. de Fisica Gleb Wataghin. Dept. de Fisica Aplicada; Furlan, Andre Luis [Universidade Estadual de Campinas (FEC/UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica

    2010-07-01

    This work provides information about the development of an integrated unit for hydrogen production by auto thermal reforming of ethanol with nominal capacity of 1 kg/h H{sub 2} 4.5 (99.995%). The unit is composed by a Fuel Processing Module (FPM), resulting from auto thermal and shift reactor integration, responsible for the thermochemical step, plus an over heater of the liquid input (EtOH and H{sub 2}O), operated recovering thermal energy from PSA blown-down (H{sub 2} Purification Module - MPH2), besides other thermal equipment which completes the integration. Using a computational routine for scaling the process and preliminary performance analysis, it was possible to optimize operating conditions, essential along unit operations design. Likewise, performance estimation of the integrated unit proceeds, which shows efficiency about 72.5% from FPM. Coupled with the PSA recovery rate, 72.7%, the unit could achieve overall energy performance of 52.7%, or 74.4% working in co-generation of hydrogen and heat. (author)

  16. Production of cobalt and nickel particles by hydrogen reduction

    Science.gov (United States)

    Forsman, J.; Tapper, U.; Auvinen, A.; Jokiniemi, J.

    2008-05-01

    Cobalt and nickel nanoparticles were produced by hydrogen reduction reaction from cobalt or nickel chloride precursor vapour in nitrogen carrier gas. This aerosol phase method to produce nanoparticles is a scalable one-step process. Two different setups were introduced in particle production: a batch type reactor and a continuously operated reactor. Common feature in these setups was hydrogen mixing in a vertical flow reactor. The process was monitored on-line for particle mass concentration and for gas phase chemical reactions. Tapered element oscillating microbalance measured the particle mass concentration and Fourier transform infrared spectroscopy was used to monitor relevant gas phase species. The produced cobalt and nickel particles were characterised using transmission electron microscopy and x-ray diffraction. The produced cobalt and nickel particles were crystalline with cubic fcc structure. Twinning was often observed in cobalt particles while nickel particles were mostly single crystals. The cobalt particles formed typically long agglomerates. No significant neck growth between the primary particles was observed. The primary particle size for cobalt and nickel was below 100 nm.

  17. Thermochemical hydrogen production via a cycle using barium and sulfur: reaction between barium sulfide and water

    Energy Technology Data Exchange (ETDEWEB)

    Ota, K.; Conger, W.L.

    1977-01-01

    The reaction between barium sulfide and water, a reaction found in several sulfur based thermochemical cycles, was investigated kinetically at 653 to 866/sup 0/C. Gaseous products were hydrogen and hydrogen sulfide. The rate determining step for hydrogen formation was a surface reaction between barium sulfide and water. The rate of formation of hydrogen can be expressed as: RH2 = 1.07 x 10/sup -2/ exp (-3180/RT) (mol H/sub 2//mol BaS s). Hydrogen sulfide was produced during the initial period of reaction and the quantity of hydrogen sulfide formed during this period decreased as the temperature of reaction was increased.

  18. Hydrogen production by co-cultures of Lactobacillus and a photosynthetic bacterium, Rhodobacter sphaeroides RV

    Energy Technology Data Exchange (ETDEWEB)

    Asada, Yasuo; Ishimi, Katsuhiro [Department of General Education, College of Science and Technology, Nihon University, Narashinodai, Chiba 274-8501 (Japan); Tokumoto, Masaru; Aihara, Yasuyuki; Oku, Masayo; Kohno, Hideki [Department of Applied Molecular Chemistry, College of Industrial Technology, Nihon University, Izumi-cho, Chiba 275-8575 (Japan); Wakayama, Tatsuki; Miyake, Jun [Research Institute for Cell Engineering, National Institute of Advanced Industrial Science and Technology, Nakoji, Amagasaki, Hyogo 661-0974 (Japan); Tomiyama, Masamitsu [Genetic Diversity Department, National Institute of Agrobiological Science, Tsukuba, Ibaraki 305-8602 (Japan)

    2006-09-15

    Hydrogen production with glucose by using co-immobilized cultures of a lactic acid bacterium, Lactobacillus delbrueckii NBRC13953, and a photosynthetic bacterium, Rhodobacter sphaeroides RV, in agar gels was studied. Glucose was converted to hydrogen gas in a yield of 7.1mol of hydrogen per mole of glucose at a maximum under illuminated conditions. (author)

  19. Aqueous-Phase Reforming of Renewable Polyols for Production of Hydrogen using Platinum Catalysts

    NARCIS (Netherlands)

    Boga, D.A.

    2013-01-01

    Hydrogen has the potential to fuel the energy needs of a more sustainable society. As hydrogen is not found in nature in any appreciable quantities, this energy carrier needs to be produced from a primary energy source. Biomass can serve as a source for sustainable hydrogen production. In principle,

  20. Hydrogen Production by Co-cultures of Rhizopus oryzae and a Photosynthetic Bacterium, Rhodobacter sphaeroides RV

    Science.gov (United States)

    Asada, Yasuo; Ishimi, Katsuhiro; Nagata, Yoko; Wakayama, Tatsuki; Miyake, Jun; Kohno, Hideki

    Hydrogen production with glucose by using co-immobilized cultures of a fungus, Rhizopus oryzae NBRC5384, and a photosynthetic bacterium, Rhodobacter sphaeroides RV, in agar gels was studied. The co-immobilized cultures converted glucose to hydrogen via lactate in a high molar yield of about 8moles of hydrogen per glucose at a maximum under illuminated conditions.

  1. Thermodynamical study on production of acetylene from coal pyrolysis in hydrogen plasma

    Energy Technology Data Exchange (ETDEWEB)

    Wang, F.; Guo, W.K.; Yuan, X.Q.; Zhao, T.Z. [Fudan University, Shanghai (China). Inst. for Modern Physics

    2006-05-15

    The chemical thermodynamic equilibrium of acetylene production by coal pyrolysis in hydrogen plasma was studied. The thermodynamic equilibrium is obtained by using the method of free energy. Calculated results show that the hydrogen concentration in the equilibrium system is very important for the acetylene production by coal conversion and the energy consumption for the production of acetylene per-kilogram strongly depends on the hydrogen concentration and the temperature.

  2. Thermodynamical Study on Production of Acetylene from Coal Pyrolysis in Hydrogen Plasma

    Science.gov (United States)

    Wang, Fei; Guo, Wenkang; Yuan, Xingqiu; Zhao, Taize

    2006-05-01

    The chemical thermodynamic equilibrium of acetylene production by coal pyrolysis in hydrogen plasma was studied. The thermodynamic equilibrium is obtained by using the method of free energy. Calculated results show that the hydrogen concentration in the equilibrium system is very important for the acetylene production by coal conversion and the energy consumption for the production of acetylene per-kilogram strongly depends on the hydrogen concentration and the temperature.

  3. Improving The Efficiency Of Ammonia Electrolysis For Hydrogen Production

    Science.gov (United States)

    Palaniappan, Ramasamy

    Given the abundance of ammonia in domestic and industrial wastes, ammonia electrolysis is a promising technology for remediation and distributed power generation in a clean and safe manner. Efficiency has been identified as one of the key issues that require improvement in order for the technology to enter the market phase. Therefore, this research was performed with the aim of improving the efficiency of hydrogen production by finding alternative materials for the cathode and electrolyte. 1. In the presence of ammonia the activity for hydrogen evolution reaction (HER) followed the trend Rh>Pt>Ru>Ni. The addition of ammonia resulted in lower rates for HER for Pt, Ru, and Ni, which have been attributed to competition from the ammonia adsorption reaction. 2. The addition of ammonia offers insight into the role of metal-hydrogen underpotential deposition (M-Hupd) on HER kinetics. In addition to offering competition via ammonia adsorption it resulted in fewer and weaker M-Hupd bonds for all metals. This finding substantiates the theory that M-Hupd bonds favor HER on Pt electrocatalyst. However, for Rh results suggest that M-Hupd bond may hinder the HER. In addition, the presence of unpaired valence shell electrons is suggested to provide higher activity for HER in the presence of ammonia. 3. Bimetals PtxM1-x (M = Ir, Ru, Rh, and Ni) offered lower overpotentials for HER compared to the unalloyed metals in the presence of ammonia. The activity of HER in the presence of ammonia follows the trend Pt-Ir>Pt-Rh>Pt-Ru>Pt-Ni. The higher activity of HER is attributed to the synergistic effect of the alloy, where ammonia adsorbs onto the more electropositive alloying metal leaving Pt available for Hupd formation and HER to take place. Additionally, this supports the theory that the presence of a higher number of unpaired electrons favors the HER in the presence of ammonia. 4. Potassium polyacrylate (PAA-K) was successfully used as a substitute for aqueous KOH for ammonia

  4. Breadand Effervescent Beverage Productions with Local Microbes for the Local Revitalization

    Directory of Open Access Journals (Sweden)

    Manami Watanabe

    2016-06-01

    Full Text Available Local microbes such as yeasts fungi and bacilli, were isolated and used to apply for the food processing (bread making and the production of an effervescent beverage (fruits kvass for promotion of the local revitalization. Our yeast isolates could contribute to make the breads that can sell in alocal bakery shop.  Furthermore, the same yeasts could be used for making the fruit kvass (a Russian effervescent beverage which was fermented by yeast with local fruit products (lemon, dry grape, mandarin orange and apple that were produced in Hiroshima prefecture in Japan. Development of merchandise having the local brand, which was made with only products of Hiroshima prefecture was attempted. Results of these activities demonstrate that the search of local microbes can help to establish the regional brand product related to its local area. They also showed that the local microbes have the potential ability to lead the local revitalization and the local brand product.

  5. Hydrogen production from salt water by Marine blue green algae and solar radiation

    Science.gov (United States)

    Mitsui, A.; Rosner, D.; Kumazawa, S.; Barciela, S.; Phlips, E.

    1985-01-01

    Two marine bluegreen algae, Oscillatoria sp. Miami BG 7 and Synechococcus sp Miami 041511 have been selected as the result of over 10 years continuous and intensive effort of isolation, growth examination, and the screening of hydrogen photoproduction capability in this laboratory. Both strains photoproduced hydrogen for several days at high rates and a quantity of hydrogen was accumulated in a closed vessel. Overall hydrogen donor substance of the hydrogen photoproduction was found to be salt water. Using strain Miami BG 7, a two step method of hydrogen photoproduction from salt water was successfully developed and this was recycled several times over a one month period using both free cells and immobilized cells in both indoor and outdoor under natural sunlight. According to these experiments, a prototype floating hydrogen production system was designed for further development of the biosolar hydrogen production system.

  6. Hydrogen production from salt water by Marine blue green algae and solar radiation

    Science.gov (United States)

    Mitsui, A.; Rosner, D.; Kumazawa, S.; Barciela, S.; Phlips, E.

    1985-01-01

    Two marine bluegreen algae, Oscillatoria sp. Miami BG 7 and Synechococcus sp Miami 041511 have been selected as the result of over 10 years continuous and intensive effort of isolation, growth examination, and the screening of hydrogen photoproduction capability in this laboratory. Both strains photoproduced hydrogen for several days at high rates and a quantity of hydrogen was accumulated in a closed vessel. Overall hydrogen donor substance of the hydrogen photoproduction was found to be salt water. Using strain Miami BG 7, a two step method of hydrogen photoproduction from salt water was successfully developed and this was recycled several times over a one month period using both free cells and immobilized cells in both indoor and outdoor under natural sunlight. According to these experiments, a prototype floating hydrogen production system was designed for further development of the biosolar hydrogen production system.

  7. Metabolic flux network analysis of fermentative hydrogen production: using Clostridium tyrobutyricum as an example.

    Science.gov (United States)

    Cheng, Hai-Hsuan; Whang, Liang-Ming; Lin, Che-An; Liu, I-Chun; Wu, Chao-Wei

    2013-08-01

    This study applies metabolic flux network analysis (MFA) to evaluate the metabolic flux of fermentative hydrogen production (FHP) with the use of Clostridium tyrobutyricum fed with either glucose or lactate/acetate as substrates. The MFA results suggest that hydraulic retention time (HRT) presents significant impact on hydrogen production from glucose. At HRT between 4 and 18 h, increase of HRT increased hydrogen production but decreased lactate production, while at HRT below 4 h decrease of HRT increased hydrogen production but decreased lactate production. The flux for lactate, butyrate and acetate seemed to affect H₂ production, due presumably to their impacts on the balance of NADH, ferredoxin and ATP. It is suggested that the MFA can be a useful tool to provide valuable information for optimization and design of the fermentative hydrogen production process.

  8. Hydrogen production by plasma electrolysis reactor of KOH-ethanol solution

    Science.gov (United States)

    Saksono, N.; Batubara, T.; Bismo, S.

    2016-11-01

    Plasma electrolysis has great potential in industrial hydrogen production, chlor-alkali production, and waste water treatment. Plasma electrolysis produces more hydrogen with less energy consumption than hydrocarbon or Faraday electrolysis. This paper investigated the hydrogen production by plasma electrolysis of KOH-ethanol solution at 80 °C and 1 atm. The effects of voltage, KOH solution, ethanol addition, and cathode deep on plasma electrolysis performance were studied. The hydrogen production was analyzed using bubble flow meter and hydrogen analyzer. The electrical energy consumption was measured by a digital multimeter. The effectiveness of plasma electrolysis in terms of hydrogen production was evaluated by comparing it with Faraday Electrolysis. The results showed that hydrogen produced by plasma electrolysis is 149 times higher than the hydrogen produced by Faraday electrolysis. The optimum hydrogen production was 50.71 mmol/min, obtained at 700 V with 0.03 M KOH, 10% vol ethanol and 6.6 cm cathode deep, with energy consumption 1.49 kJ/mmol. The result demonstrates a promising path for hydrogen production by utilizing plasma electrolysis reactor.

  9. The effect of temperature and light intensity on hydrogen production by Rhodobacter capsulatus

    Energy Technology Data Exchange (ETDEWEB)

    Eroglu, Inci [Middle East Technical Univ., Ankara (Turkey). Dept. of Chemical Engineering; Sevinc, Pelin [Middle East Technical Univ., Ankara (Turkey). Dept. of Biotechnology; Guenduez, Ufuk; Yucel, Meral [Middle East Technical Univ., Ankara (Turkey). Dept. of Biological Sciences

    2010-07-01

    Rhodobacter capsulatus is a purple non-sulfur photosynthetic bacterium which can produce hydrogen by photofermentation on acetate and lactate. Hydrogen productivity depends on several parameters such as medium composition, pH, light intensity and temperature. In the present study, the effects of temperature and light intensity on hydrogen production were investigated. The cell growth curve has been fitted to the logistic model and hydrogen productivity was interpreted by Modified Gompertz Equation. The maximum productivity was obtained at 30 C and light intensity of 4000 lux. (orig.)

  10. Thermodynamic analysis of Glycerol Steam Reforming for hydrogen production with in situ hydrogen and carbon dioxide separation

    Science.gov (United States)

    Silva, Joel M.; Soria, M. A.; Madeira, Luis M.

    2015-01-01

    A thermodynamic study of Glycerol Steam Reforming (GSR) for hydrogen production with in situ carbon dioxide and hydrogen (reaction products) simultaneous removal was performed. The sorption-enhanced membrane reactor (SEMR) was divided into multiple sub-Gibbs reactors and the Gibbs free energy minimization method was employed. The effects of temperature (600-800 K), molar water-to-glycerol feed ratio (WGFR) (3-9), pressure (1-5 atm) and fraction of hydrogen and carbon dioxide removal (f, 0-0.99) on the GSR process were target of investigation. A hydrogen yield (total moles of hydrogen produced/mole of reacted glycerol) very close to the stoichiometric value of 7 was obtained at 700 K, WGFR of 9, 1 atm and for fCO2 = 0.99 and fH2 = 0.80. This corresponds to an enhancement of 217%, 47% and 22% in terms of hydrogen yield comparatively to the traditional reactor (TR), sorption-enhanced reactor (SER) with carbon dioxide capture (fCO2 = 0.99) and membrane reactor (MR) with hydrogen separation (fH2 = 0.80) , respectively. In terms of coke, its formation was only observed under WGFRs below the stoichiometric value of 3.

  11. Hydrogen and hydrogen isotopes handling experience in heavy water production and related industries

    Energy Technology Data Exchange (ETDEWEB)

    Aprea, J.L. [Argentine Atomic Energy Commission, Comahue Univ., Neuquen (Argentina)

    2002-07-01

    Beyond the conventional applications in the chemical, petrochemical, food and other process industries, hydrogen is also used in nuclear-related industries, where it is required as an active ingredient in large-scale processes to produce heavy water. The experience obtained during the design, construction and operation of such industrial installations, which use hydrogen, deuterium and hydrogen-containing compounds can contribute in favor of the development of safer hydrogen energy facilities. Thus, material selection, properties degradation studies and preventing technologies applied in the heavy water operations are useful tools that will help to overtake the transition towards the hydrogen civilization. (Author)

  12. Control design for an autonomous wind based hydrogen production system

    Energy Technology Data Exchange (ETDEWEB)

    Valenciaga, F.; Evangelista, C.A. [CONICET, Laboratorio de Electronica Industrial Control e Instrumentacion (LEICI), Facultad de Ingenieria, Universidad Nacional de La Plata, CC.91, C.P. 1900, La Plata (Argentina)

    2010-06-15

    This paper presents a complete control scheme to efficiently manage the operation of an autonomous wind based hydrogen production system. This system comprises a wind energy generation module based on a multipolar permanent magnet synchronous generator, a lead-acid battery bank as short term energy storage and an alkaline von Hoerner electrolyzer. The control is developed in two hierarchical levels. The higher control level or supervisor control determines the general operation strategy for the whole system according to the wind conditions and the state of charge of the battery bank. On the other hand, the lower control level includes the individual controllers that regulate the respective module operation assuming the set-points determined by the supervisor control. These last controllers are approached using second-order super-twisting sliding mode techniques. The performance of the closed-loop system is assessed through representative computer simulations. (author)

  13. Hydrogen production via thermochemical cycles based on sulfur chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Soliman, M.A.; Conger, W.L.; Carty, R.H.; Funk, J.E.; Cox, K.E.

    1976-01-01

    A class of closed thermochemical cycles for hydrogen production based on sulfur chemistry is presented. This class is described by the following set of chemical reactions: M + H/sub 2/O reversible MO + H/sub 2/ (low temperature); MO + 0.5S reversible M + 0.5SO/sub 2/ (high temperature); M'O + 1.5SO/sub 2/ reversible M'SO/sub 4/ + 0.5S (low temperature); and M'SO/sub 4/ reversible M'O + SO/sub 2/ + 0.5O/sub 2/ (high temperature). Experimental investigation of some of the reactions is presented. Thermodynamic analysis indicates efficiencies of the range of 40 to 50 percent and sometimes higher. Not all of the reactions in the proposed cycles have been verified in the literature or through experimentation.

  14. Fermentative hydrogen production in anaerobic membrane bioreactors: A review.

    Science.gov (United States)

    Bakonyi, P; Nemestóthy, N; Simon, V; Bélafi-Bakó, K

    2014-03-01

    Reactor design considerations are crucial aspects of dark fermentative hydrogen production. During the last decades, many types of reactors have been developed and used in order to drive biohydrogen technology towards practicality and economical-feasibility. In general, the ultimate aim is to improve the key features of the process, namely the H2 yields and generation rates. Among the various configurations, the traditional, completely stirred tank reactors (CSTRs) are still the most routinely employed ones. However, due to their limitations, there is a progress to develop more reliable alternatives. One of the research directions points to systems combining membranes, which are called as anaerobic membrane bioreactors (AnMBRs). The aim of this paper is to summarize and highlight the recent biohydrogen related work done on AnMBRs and moreover to evaluate their performances and potentials in comparison with their conventional CSTR counterparts.

  15. IEA Agreement on the production and utilization of hydrogen: 1999 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Elam, Carolyn C. (National Renewable Energy Lab, Golden, CO (US)) (ed.)

    2000-01-31

    The annual report begins with an overview of the IEA Hydrogen Agreement, including guiding principles and their strategic plan followed by the Chairman's report providing the year's highlights. Annex reports included are: the final report for Task 11, Integrated Systems; task updates for Task 12, Metal Hydrides and Carbon for Hydrogen Storage, Task 13, Design and Optimization of Integrated Systems, Task 14, Photoelectrolytic Production of Hydrogen, and Task 15, Photobiological Production of Hydrogen; and a feature article by Karsten Wurr titled 'Large-Scale Industrial Uses of Hydrogen: Final Development Report'.

  16. IEA agreement on the production and utilization of hydrogen: 2000 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Elam, Carolyn C. [National Renewable Energy Lab., Golden, CO (US)] (ed.)

    2001-12-01

    The 2000 annual report of the IEA Hydrogen Agreement contains an overview of the agreement, including its guiding principles, latest strategic plan, and a report from the Chairman, Mr. Neil P. Rossmeissl, U.S. Department of Energy. Overviews of the National Hydrogen Programs of nine member countries are given: Canada, Japan, Lithuania, the Netherlands, Norway, Spain, Sweden, Switzerland, and the United States. Task updates are provided on the following annexes: Annex 12 - Metal Hydrides and Carbon for Hydrogen Storage, Annex 13 - Design and Optimization of Integrated Systems, Annex 14 - Photoelectrolytic Production of Hydrogen, and, Annex 15 - Photobiological Production of Hydrogen.

  17. Carbon Dioxide-Free Hydrogen Production with Integrated Hydrogen Separation and Storage.

    Science.gov (United States)

    Dürr, Stefan; Müller, Michael; Jorschick, Holger; Helmin, Marta; Bösmann, Andreas; Palkovits, Regina; Wasserscheid, Peter

    2017-01-10

    An integration of CO2 -free hydrogen generation through methane decomposition coupled with hydrogen/methane separation and chemical hydrogen storage through liquid organic hydrogen carrier (LOHC) systems is demonstrated. A potential, very interesting application is the upgrading of stranded gas, for example, gas from a remote gas field or associated gas from off-shore oil drilling. Stranded gas can be effectively converted in a catalytic process by methane decomposition into solid carbon and a hydrogen/methane mixture that can be directly fed to a hydrogenation unit to load a LOHC with hydrogen. This allows for a straight-forward separation of hydrogen from CH4 and conversion of hydrogen to a hydrogen-rich LOHC material. Both, the hydrogen-rich LOHC material and the generated carbon on metal can easily be transported to destinations of further industrial use by established transport systems, like ships or trucks. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Hydrogen production by Anabaena sp. CH1 with 2-stage process

    Energy Technology Data Exchange (ETDEWEB)

    Chiang, C.L.; Lee, C.M. [National Chung Hsing Univ., Taiwan (China). Dept. of Environmental Engineering; Chen, P.C. [Hungkuang Univ., Taiwan (China). Dept. of Biomedical Nutrition

    2009-07-01

    While hydrogen can be produced by cyanobacteria under anoxic conditions, chlorophylls can break down and provide the nitrogen needed for cell material synthesis. The breakdown of chlorophylls is unfavorable for the long-term production of hydrogen. This study provided details of a 2-stage operation designed to prevent chlorophyll breakdown. Anabaena sp. CH1 was used in both the hydrogen production and recovery stages. Nitrogenase activity, chlorophyll concentrations, and hydrogen production rates decreased to 54 per cent after argon gases were used for a 3-day period. Growth conditions than shifted to normal conditions after 3 to 5 days. Cells recovered their nitrogenase activities, biomass, and chlorophyll concentrations within 4 days. The recovery stage then shifted to the hydrogen production stage, where hydrogen production rates were as high as previous observed rates. It was concluded that the effects of nitrogen deprivation on photosynthetic mechanisms are reversible.

  19. Steam Methane Reforming System for Hydrogen Production: Advanced Exergetic Analysis

    Directory of Open Access Journals (Sweden)

    Tatiana Morosuk

    2012-02-01

    Full Text Available Steam methane reforming (SMR is one of the most promising processes for the production of hydrogen. Therefore, the overall thermodynamic efficiency of this process is of particular importance. The thermodynamic inefficiencies in a thermal system are related to exergy destruction and exergy loss. However, a conventional exergetic analysis cannot evaluate the mutual interdependencies among the system components nor the real potential for improving the energy conversion system being considered. One of the tools under development for the improvement of energy conversion systems from the thermodynamic viewpoint is the advanced exergetic analysis. In this paper, the avoidable part of the exergy destruction is estimated and the interactions among components of the overall system are evaluated in terms of endogenous and exogenous exergy destruction. The assumptions required for these calculations are discussed in detail, especially for those components that are typically used in chemical processes. Results of this paper suggest options for increasing the thermodynamic efficiency of hydrogen production by steam-methane reforming.

  20. Thermodynamic evaluation of methanol steam reforming for hydrogen production

    Science.gov (United States)

    Faungnawakij, Kajornsak; Kikuchi, Ryuji; Eguchi, Koichi

    Thermodynamic equilibrium of methanol steam reforming (MeOH SR) was studied by Gibbs free minimization for hydrogen production as a function of steam-to-carbon ratio (S/C = 0-10), reforming temperature (25-1000 °C), pressure (0.5-3 atm), and product species. The chemical species considered were methanol, water, hydrogen, carbon dioxide, carbon monoxide, carbon (graphite), methane, ethane, propane, i-butane, n-butane, ethanol, propanol, i-butanol, n-butanol, and dimethyl ether (DME). Coke-formed and coke-free regions were also determined as a function of S/C ratio. Based upon a compound basis set MeOH, CO 2, CO, H 2 and H 2O, complete conversion of MeOH was attained at S/C = 1 when the temperature was higher than 200 °C at atmospheric pressure. The concentration and yield of hydrogen could be achieved at almost 75% on a dry basis and 100%, respectively. From the reforming efficiency, the operating condition was optimized for the temperature range of 100-225 °C, S/C range of 1.5-3, and pressure at 1 atm. The calculation indicated that the reforming condition required from sufficient CO concentration (<10 ppm) for polymer electrolyte fuel cell application is too severe for the existing catalysts (T r = 50 °C and S/C = 4-5). Only methane and coke thermodynamically coexist with H 2O, H 2, CO, and CO 2, while C 2H 6, C 3H 8, i-C 4H 10, n-C 4H 10, CH 3OH, C 2H 5OH, C 3H 7OH, i-C 4H 9OH, n-C 4H 9OH, and C 2H 6O were suppressed at essentially zero. The temperatures for coke-free region decreased with increase in S/C ratios. The impact of pressure was negligible upon the complete conversion of MeOH.

  1. Analysis of the potential for hydrogen production in the province of Cordoba, Argentina, from wind resources

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, C.R.; Santa Cruz, R.; Aisa, S. [Universidad Empresarial Siglo 21, Monsenor Pablo Cabrera s/n calle, 5000 Cordoba (Argentina); Riso, M.; Jimenez Yob, G.; Ottogalli, R. [Subsecretaria de Infraestructuras y Programas, Ministerio de Obras y Servicios Publicos del Gobierno de la Provincia de Cordoba, Av. Poeta Lugones 12, 2do. Piso, 5000 Cordoba (Argentina); Jeandrevin, G. [Instituto Universitario Aeronautico, Avenida Fuerza Aerea km 6 1/2, 5022 Cordoba (Argentina); Leiva, E.P.M. [INFIQC, Unidad de Matematica y Fisica, Facultad de Ciencias Quimicas, Universidad Nacional de Cordoba, Haya de la Torre s/n, 5010 Cordoba (Argentina)

    2010-06-15

    The potential for hydrogen production from wind resources in the province of Cordoba, second consumer of fossil fuels for transportation in Argentina, is analyzed. Three aspects of the problem are considered: the evaluation of the hydrogen resource from wind power, the analysis of the production costs via electrolysis and the annual requirements of wind energy to generate hydrogen to fuel the vehicular transport of the province. Different scenarios were considered, including pure hydrogen as well as the so-called CNG plus, where hydrogen is mixed with compressed natural gas in a 20% V/V dilution of the former. The potential for hydrogen production from wind resources is analyzed for each department of the province, excluding those regions not suited for wind farms. The analysis takes into account the efficiency of the electrolyzer and the capacity factor of the wind power system. It is concluded that the automotive transportation could be supplied by hydrogen stemming from wind resources via electrolysis. (author)

  2. Biochemical and genetic engineering strategies to enhance hydrogen production in photosynthetic algae and cyanobacteria.

    Science.gov (United States)

    Srirangan, Kajan; Pyne, Michael E; Perry Chou, C

    2011-09-01

    As an energy carrier, hydrogen gas is a promising substitute to carbonaceous fuels owing to its superb conversion efficiency, non-polluting nature, and high energy content. At present, hydrogen is predominately synthesized via chemical reformation of fossil fuels. While various biological methods have been extensively explored, none of them is justified as economically feasible. A sustainable platform for biological production of hydrogen will certainly impact the biofuel market. Among a selection of biological systems, algae and cyanobacteria have garnered major interests as potential cell factories for hydrogen production. In conjunction with photosynthesis, these organisms utilize inexpensive inorganic substrates and solar energy for simultaneous biosynthesis and hydrogen evolution. However, the hydrogen yield associated with these organisms remains far too low to compete with the existing chemical systems. This article reviews recent advances of biochemical, bioprocess, and genetic engineering strategies in circumventing technological limitations to hopefully improve the applicative potential of these photosynthetic hydrogen production systems. Copyright © 2011 Elsevier Ltd. All rights reserved.

  3. [Isolation and characterization of new species hydrogen producing bacterium Ethanologenbacterium sp. strain X-1 and its capability of hydrogen production].

    Science.gov (United States)

    Xing, De-Feng; Ren, Nan-Qi; Li, Qiu-Bo

    2004-12-01

    To obtain hydrogen-producing bacterium of high efficiency, a strain X-1 of hydrogen-producing bacteria was isolated from the continuous stirred-tank reactor (CSTR) by anaerobic Hungate technique. The Comparative sequence analysis of 16S rDNA showed that homology of strain X-1 with Clostridium cellulose and Acetanaerobacterium elongatum is less than 94%. All sequence alignment of 16S-23S rDNA intergenic spacer regions (ISR) indicated displayed that consensus region is tRNA(Ala), and tRNA(Ile), variable region is not homologous. Morphological, physic-biochemical character, and comparative sequence analysis of 16S rDNA and 16S-23S rDNA ISR indicated that strain X-1 belong to new genus named Ethanologenbacterium gen. nov.. Strain X-1 is facultative anaerobe bacillus; its main fermentative products are acetic acid, ethanol, H2 and CO2. The metabolic character of strain X-1 is typical ethanol type fermentation. Its capability of hydrogen production was measured in the batch culture experiment. X-1's maximum specific hydrogen producing rate is 28.3 mmol H2/( g dry cell x h) at pH 4.0 and 36 degrees C. Result of identify and analysis of hydrogen production ability demonstrated strain X-1 belong to new genus of high hydrogen-producing bacteria.

  4. The Van der Waals interaction of the hydrogen molecule an exact local energy density functional

    CERN Document Server

    Choy, T C

    1999-01-01

    We verify that the van der Waals interaction and hence all dispersion interactions for the hydrogen molecule given by: W''= -{A/R^6}-{B/R^8}-{C/R^10}- ..., in which R is the internuclear separation, are exactly soluble. The constants A=6.4990267..., B=124.3990835 ... and C=1135.2140398... (in Hartree units) first obtained approximately by Pauling and Beach (PB) [1] using a linear variational method, can be shown to be obtainable to any desired accuracy via our exact solution. In addition we shall show that a local energy density functional can be obtained, whose variational solution rederives the exact solution for this problem. This demonstrates explicitly that a static local density functional theory exists for this system. We conclude with remarks about generalising the method to other hydrogenic systems and also to helium.

  5. Hydrogen Peroxide as a Sustainable Energy Carrier: Electrocatalytic Production of Hydrogen Peroxide and the Fuel Cell.

    Science.gov (United States)

    Fukuzumi, Shunichi; Yamada, Yusuke; Karlin, Kenneth D

    2012-11-01

    This review describes homogeneous and heterogeneous catalytic reduction of dioxygen with metal complexes focusing on the catalytic two-electron reduction of dioxygen to produce hydrogen peroxide. Whether two-electron reduction of dioxygen to produce hydrogen peroxide or four-electron O2-reduction to produce water occurs depends on the types of metals and ligands that are utilized. Those factors controlling the two processes are discussed in terms of metal-oxygen intermediates involved in the catalysis. Metal complexes acting as catalysts for selective two-electron reduction of oxygen can be utilized as metal complex-modified electrodes in the electrocatalytic reduction to produce hydrogen peroxide. Hydrogen peroxide thus produced can be used as a fuel in a hydrogen peroxide fuel cell. A hydrogen peroxide fuel cell can be operated with a one-compartment structure without a membrane, which is certainly more promising for the development of low-cost fuel cells as compared with two compartment hydrogen fuel cells that require membranes. Hydrogen peroxide is regarded as an environmentally benign energy carrier because it can be produced by the electrocatalytic two-electron reduction of O2, which is abundant in air, using solar cells; the hydrogen peroxide thus produced could then be readily stored and then used as needed to generate electricity through the use of hydrogen peroxide fuel cells.

  6. Hydrogen Peroxide as a Sustainable Energy Carrier: Electrocatalytic Production of Hydrogen Peroxide and the Fuel Cell

    Science.gov (United States)

    Fukuzumi, Shunichi; Yamada, Yusuke; Karlin, Kenneth D.

    2012-01-01

    This review describes homogeneous and heterogeneous catalytic reduction of dioxygen with metal complexes focusing on the catalytic two-electron reduction of dioxygen to produce hydrogen peroxide. Whether two-electron reduction of dioxygen to produce hydrogen peroxide or four-electron O2-reduction to produce water occurs depends on the types of metals and ligands that are utilized. Those factors controlling the two processes are discussed in terms of metal-oxygen intermediates involved in the catalysis. Metal complexes acting as catalysts for selective two-electron reduction of oxygen can be utilized as metal complex-modified electrodes in the electrocatalytic reduction to produce hydrogen peroxide. Hydrogen peroxide thus produced can be used as a fuel in a hydrogen peroxide fuel cell. A hydrogen peroxide fuel cell can be operated with a one-compartment structure without a membrane, which is certainly more promising for the development of low-cost fuel cells as compared with two compartment hydrogen fuel cells that require membranes. Hydrogen peroxide is regarded as an environmentally benign energy carrier because it can be produced by the electrocatalytic two-electron reduction of O2, which is abundant in air, using solar cells; the hydrogen peroxide thus produced could then be readily stored and then used as needed to generate electricity through the use of hydrogen peroxide fuel cells. PMID:23457415

  7. Local Interstellar Hydrogen's Disappearance at 1 Au: Four Years of IBEX in the Rising Solar Cycle

    CERN Document Server

    Saul, Lukas; Fuselier, Stephen; Kubiak, Marzena; McComas, Dave; Möbius, Eberhard; Sokół, Justina; Rodríguez, Diego; Scheer, Juergen; Wurz, Peter

    2013-01-01

    NASA's Interstellar Boundary Explorer (IBEX) mission has recently opened a new window on the interstellar medium (ISM) by imaging neutral atoms. One "bright" feature in the sky is the interstellar wind flowing into the solar system. Composed of remnants of stellar explosions as well as primordial gas and plasma, the ISM is by no means uniform. The interaction of the local ISM with the solar wind shapes our heliospheric environment with hydrogen being the dominant component of the very local ISM. In this paper, we report on direct sampling of the neutral hydrogen of the local ISM over four years of IBEX observations. The hydrogen wind observed at 1 AU has decreased and nearly disappeared as the solar activity has increased over the last four years; the signal at 1 AU has dropped off in 2012 by a factor of ~8 to near background levels. The longitudinal offset has also increased with time presumably due to greater radiation pressure deflecting the interstellar wind. We present longitudinal and latitudinal arriva...

  8. The Development of Materials for the Production of Hydrogen from Bio-ethanol

    Institute of Scientific and Technical Information of China (English)

    Pilar; Ramírez; de; la; Piscina; Narcís; Homs

    2007-01-01

    1 Results There is an increased interest in the hydrogen production from renewable sources. In this context, recently, numerous studies which use ethanol for hydrogen production have appeared. Ethanol is easily handled, non-toxic, and it can be obtained from biomass. The steam-reforming of bioethanol has been shown to beeffective for hydrogen production:C2H5OH + 3 H2O  6 H2 + 2 CO2. Six moles of hydrogen can be yielded for each mole of ethanol reacted. However, depending on the catalyst used, other und...

  9. Hydrogen and methane production from household solid waste in the two-stage fermentation process

    DEFF Research Database (Denmark)

    Lui, D.; Liu, D.; Zeng, Raymond Jianxiong

    2006-01-01

    A two-stage process combined hydrogen and methane production from household solid waste was demonstrated working successfully. The yield of 43 mL H-2/g volatile solid (VS) added was generated in the first hydrogen production stage and the methane production in the second stage was 500 mL CH4/g VS....... Furthermore, this study also provided direct evidence in the dynamic fermentation process that, hydrogen production increase was reflected by acetate to butyrate ratio increase in liquid phase. (c) 2006 Elsevier Ltd. All rights reserved.......A two-stage process combined hydrogen and methane production from household solid waste was demonstrated working successfully. The yield of 43 mL H-2/g volatile solid (VS) added was generated in the first hydrogen production stage and the methane production in the second stage was 500 mL CH4/g VS...... added. This figure was 21% higher than the methane yield from the one-stage process, which was run as control. Sparging of the hydrogen reactor with methane gas resulted in doubling of the hydrogen production. PH was observed as a key factor affecting fermentation pathway in hydrogen production stage...

  10. Bio-Inspired Molecular Catalysts for Hydrogen Oxidation and Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Ho, Ming-Hsun; Chen, Shentan; Rousseau, Roger J.; Dupuis, Michel; Bullock, R. Morris; Raugei, Simone

    2013-06-03

    Recent advances in Ni-based bio-inspired catalysts obtained in the Center for Molecular Electrocatalysis, an Energy Frontier Research Center (EFRC) at the Pacific Northwest National Laboratory, demonstrated the possibility of cleaving H2 or generating H2 heterolytically with turnover frequencies comparable or superior to those of hydrogenase enzymes. In these catalysts the transformation between H2 and protons proceeds via an interplay between proton, hydride and electron transfer steps and involves the interaction of a dihydrogen molecule with both a Ni(II) center and with pendant amine bases incorporated in a six-membered ring, which act as proton relays. These catalytic platforms are well designed in that when protons are correctly positioned (endo) toward the Raugei-ACS-Books.docxPrinted 12/18/12 2 metal center, catalysis proceeds at very high rates. We will show that the proton removal (for H2 oxidation) and proton delivery (for H2 production) are often the rate determining steps. Furthermore, the presence of multiple protonation sites gives rise to reaction intermediates with protons not correctly positioned (exo relative to the metal center). These isomers are easily accessible kinetically and are detrimental to catalysis because of the slow isomerization processes necessary to convert them to the catalytically competent endo isomers. In this chapter we will review the major findings of our computational investigation on the role of proton relays for H2 chemistry and provide guidelines for the design of new catalysts. This research was carried out in the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science. Pacific Northwest National Laboratory is operated for the U.S. Department of Energy by Battelle. Computational resources were provided at W. R. Wiley Environmental Molecular Science Laboratory (EMSL), a Raugei-Bio-Inspired Molecular-Catalysts-for-Hydrogen- Oxidation-and-Hydrogen-Production

  11. Microbiology and optimization of hydrogen fermentation and bioelectricity production

    Energy Technology Data Exchange (ETDEWEB)

    Makinen, A.

    2013-11-01

    This work investigated dark fermentative hydrogen (H{sub 2}) and bioelectricity production from carbohydrates. Meso- and thermophilic fermentative and mesophilic exoelectrogenic bacteria were enriched from different natural sources. The H{sub 2} production from different hexoses and pentoses, them main constituents of lignocellulose, was studied in batch assays. H{sub 2} production from xylose was examined in continuous stirred tank reactor (CSTR). Operational parameters for H{sub 2} production were optimized. Bioelectricity production was studied in microbial fuel cells and process parameters were optimized. Dynamics of microbial communities in H{sub 2} and bioelectricity production processes were determined. A novel thermophilic dark fermentative H{sub 2} producing bacterium, Thermovorax subterraneus, was enriched and isolated from geothermal underground mine. T. subterraneus had the optimum growth temperature of 72 deg C and the maximum H{sub 2} yield of 1.4 mol/mol glucose in batch assay. The main soluble fermentative end products of T. subterraneus were acetate and ethanol. Thermophilic dark fermentative mixed culture enriched from hot spring (Hisarlan, Turkey) had the maximum H{sub 2} yield of 1.7 mol/mol glucose. The optimal environmental parameters to maximize H{sub 2} yield were temperature 52 deg C, initial pH 6.5, 40 mg/L Fe{sup 2+}, 4.5 g/L yeast extract and glucose concentration of 4 g/L. Increasing the glucose concentration to 18 g/L increased the maximum H{sub 2} production rate to 56.2 mmol H{sub 2}/h/L. Environmental parameters had a significant effect on metabolic pathways of fermentation. Another hot spring (Hisarkoy, Turkey) enrichment culture was able to ferment different sugars to H{sub 2} favoring pentoses over hexoses. The best H{sub 2} yields in batch assays were obtained from pentoses: xylose, arabinose and ribose yielded 21, 15 and 8 % of the theoretical yield, respectively; whilst on glucose the yield was only 2 % of the theoretical

  12. Quantum molecular dynamics simulations of hydrogen production and solar cells

    Science.gov (United States)

    Mou, Weiwei

    The global energy crisis presents two major challenges for scientists around the world: Producing cleaner energy which is sustainable for the environment; And improving the efficiency of energy production as well as consumption. It is crucial and yet elusive to understand the atomistic mechanisms and electronic properties, which are needed in order to tackle those challenges. Quantum molecular dynamics simulations and nonadiabatic quantum molecular dynamics are two of the dominant methods used to address the atomistic and electronic properties in various energy studies. This dissertation is an ensemble of three studies in energy research: (1) Hydrogen production from the reaction of aluminum clusters with water to provide a renewable energy cycle; (2) The photo-excited charge transfer and recombination at a quaterthiophene/zinc oxide interface to improve the power conversion efficiency of hybrid poly(3-hexylthiophene) (P3HT) /ZnO solar cells; and (3) the charge transfer at a rubrene/C60 interface to understand why phenyl groups in rubrene improve the performance of rubrene/C60 solar cells.

  13. Hydrogen production by water dissociation using ceramic membranes - annual report for FY 2010.

    Energy Technology Data Exchange (ETDEWEB)

    Balachandran, U.; Dorris, S. E.; Emerson, J. E.; Lee, T. H.; Lu, Y.; Park, C. Y.; Picciolo, J. J. (Energy Systems)

    2011-03-14

    The objective of this project is to develop dense ceramic membranes that can produce hydrogen via coal/coal gas-assisted water dissociation without using an external power supply or circuitry. This project grew from an effort to develop a dense ceramic membrane for separating hydrogen from gas mixtures such as those generated during coal gasification, methane partial oxidation, and water-gas shift reactions. That effort led to the development of various cermet (i.e., ceramic/metal composite) membranes that enable hydrogen production by two methods. In one method, a hydrogen transport membrane (HTM) selectively removes hydrogen from a gas mixture by transporting it through either a mixed protonic/electronic conductor or a hydrogen transport metal. In the other method, an oxygen transport membrane (OTM) generates hydrogen mixed with steam by removing oxygen that is generated through water splitting. This project focuses on the development of OTMs that efficiently produce hydrogen via the dissociation of water. Supercritical boilers offer very high-pressure steam that can be decomposed to provide pure hydrogen using OTMs. Oxygen resulting from the dissociation of steam can be used for coal gasification, enriched combustion, or synthesis gas production. Hydrogen and sequestration-ready CO{sub 2} can be produced from coal and steam by using the membrane being developed in this project. Although hydrogen can also be generated by high-temperature steam electrolysis, producing hydrogen by water splitting with a mixed-conducting membrane requires no electric power or electrical circuitry.

  14. Hydrogen production by water dissociation using ceramic membranes - annual report for FY 2008.

    Energy Technology Data Exchange (ETDEWEB)

    Balachandran, U.; Dorris, S. E.; Emerson, J. E.; Lee, T. H.; Lu, Y.; Park, C. Y.; Picciolo, J. J.; Energy Systems

    2009-03-25

    The objective of this project is to develop dense ceramic membranes that, without using an external power supply or circuitry, can produce hydrogen via coal/coal gas-assisted water dissociation. This project grew from an effort to develop a dense ceramic membrane for separating hydrogen from gas mixtures such as those generated during coal gasification, methane partial oxidation, and water-gas shift reactions. That effort led to the development of various cermet (i.e., ceramic/metal composite) membranes that enable hydrogen production by two methods. In one method, a hydrogen transport membrane (HTM) selectively removes hydrogen from a gas mixture by transporting it through either a mixed protonic/electronic conductor or a hydrogen transport metal. In the other method, an oxygen transport membrane (OTM) generates hydrogen mixed with steam by removing oxygen that is generated through water splitting. This project focuses on the development of OTMs that efficiently produce hydrogen via the dissociation of water. Supercritical boilers offer very high-pressure steam that can be decomposed to provide pure hydrogen by means of OTMs. Oxygen resulting from the dissociation of steam can be used for coal gasification, enriched combustion, or synthesis gas production. Hydrogen and sequestration-ready CO{sub 2} can be produced from coal and steam by using the membrane being developed in this project. Although hydrogen can also be generated by high-temperature steam electrolysis, producing hydrogen by water splitting with a mixed-conducting membrane requires no electric power or electrical circuitry.

  15. Hydrogen production by water dissociation using ceramic membranes. Annual report for FY 2009.

    Energy Technology Data Exchange (ETDEWEB)

    Balachandran, U.; Dorris, S. E.; Emerson, J. E.; Lee, T. H.; Lu, Y.; Park, C. Y.; Picciolo, J. J.; Energy Systems

    2010-04-20

    The objective of this project is to develop dense ceramic membranes that can produce hydrogen via coal/coal gas-assisted water dissociation without using an external power supply or circuitry. This project grew from an effort to develop a dense ceramic membrane for separating hydrogen from gas mixtures such as those generated during coal gasification, methane partial oxidation, and water-gas shift reactions. That effort led to the development of various cermet (i.e., ceramic/metal composite) membranes that enable hydrogen production by two methods. In one method, a hydrogen transport membrane selectively removes hydrogen from a gas mixture by transporting it through either a mixed protonic/electronic conductor or a hydrogen transport metal. In the other method, an oxygen transport membrane (OTM) generates hydrogen mixed with steam by removing oxygen that is generated through water splitting. This project focuses on the development of OTMs that efficiently produce hydrogen via the dissociation of water. Supercritical boilers offer very high-pressure steam that can be decomposed to provide pure hydrogen by means of OTMs. Oxygen resulting from the dissociation of steam can be used for coal gasification, enriched combustion, or synthesis gas production. Hydrogen and sequestration-ready CO{sub 2} can be produced from coal and steam by using the membrane being developed in this project. Although hydrogen can also be generated by high-temperature steam electrolysis, producing hydrogen by water splitting with a mixed-conducting membrane requires no electric power or electrical circuitry.

  16. Combined hydrogen production and storage with subsequent carbon crystallization.

    Science.gov (United States)

    Lueking, Angela D; Gutierrez, Humberto R; Fonseca, Dania A; Narayanan, Deepa L; Van Essendelft, Dirk; Jain, Puja; Clifford, Caroline E B

    2006-06-21

    We provide evidence of low-temperature hydrogen evolution and possible hydrogen trapping in an anthracite coal derivative, formed via reactive ball milling with cyclohexene. No molecular hydrogen is added to the process. Raman-active molecular hydrogen vibrations are apparent in samples at atmospheric conditions (300 K, 1 bar) for samples prepared 1 year previously and stored in ambient air. Hydrogen evolves slowly at room temperature and is accelerated upon sample heating, with a first increase in hydrogen evolution occurring at approximately 60 degrees C. Subsequent chemical modification leads to the observation of crystalline carbons, including nanocrystalline diamond surrounded by graphene ribbons, other sp2-sp3 transition regions, purely graphitic regions, and a previously unidentified crystalline carbon form surrounded by amorphous carbon. The combined evidence for hydrogen trapping and carbon crystallization suggests hydrogen-induced crystallization of the amorphous carbon materials, as metastable hydrogenated carbons formed via the high-energy milling process rearrange into more thermodynamically stable carbon forms and molecular hydrogen.

  17. Rational Design of Porous Conjugated Polymers and Roles of Residual Palladium for Photocatalytic Hydrogen Production.

    Science.gov (United States)

    Li, Lianwei; Cai, Zhengxu; Wu, Qinghe; Lo, Wai-Yip; Zhang, Na; Chen, Lin X; Yu, Luping

    2016-06-22

    Developing highly efficient photocatalyts for water splitting is one of the grand challenges in solar energy conversion. Here, we report the rational design and synthesis of porous conjugated polymer (PCP) that photocatalytically generates hydrogen from water splitting. The design mimics natural photosynthetics systems with conjugated polymer component to harvest photons and the transition metal part to facilitate catalytic activities. A series of PCPs have been synthesized with different light harvesting chromophores and transition metal binding bipyridyl (bpy) sites. The photocatalytic activity of these bpy-containing PCPs can be greatly enhanced due to the improved light absorption, better wettability, local ordering structure, and the improved charge separation process. The PCP made of strong and fully conjugated donor chromophore DBD (M4) shows the highest hydrogen production rate at ∼33 μmol/h. The results indicate that copolymerization between a strong electron donor and weak electron acceptor into the same polymer chain is a useful strategy for developing efficient photocatalysts. This study also reveals that the residual palladium in the PCP networks plays a key role for the catalytic performance. The hydrogen generation activity of PCP photocatalyst can be further enhanced to 164 μmol/h with an apparent quantum yield of 1.8% at 350 nm by loading 2 wt % of extra platinum cocatalyst.

  18. Study of the Behavior of Titanium Alloys as the Cathode for Photovoltaic Hydrogen Production

    Directory of Open Access Journals (Sweden)

    Chien-Lung Huang

    2013-01-01

    Full Text Available CP-Ti and Ti-153 were adopted in this study to observe their electrochemical behavior in serving as the cathode for photovoltaic hydrogen production. The designed cyclic hydrogenation-solution heat treating processes were performed to increase the hydrogen uptake for both alloys. The results are as follows. (1 Both arsenic trioxide and thiourea showed hydrogenation promotive effect on CP-Ti, while thiourea was an inhibitor for Ti-153 under the applied conditions. (2 Arsenic trioxide showed hydrogenation promotive effect on both Ti-153 and CP-Ti in this study. (3 Ti-153 demonstrated superiority to CP-Ti when serves as the cathode for photovoltaic hydrogen production. The hydrogen mass payload for Ti-153 is 68 times larger than that for CP-Ti.

  19. Microbial culture selection for bio-hydrogen production from waste ground wheat by dark fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Argun, Hidayet; Kargi, Fikret; Kapdan, Ilgi K. [Department of Environmental Engineering, Dokuz Eylul University, Buca, Izmir (Turkey)

    2009-03-15

    Hydrogen formation performances of different anaerobic bacteria were investigated in batch dark fermentation of waste wheat powder solution (WPS). Serum bottles containing wheat powder were inoculated with pure cultures of Clostridium acetobutylicum (CAB), Clostridium butyricum (CB), Enterobacter aerogenes (EA), heat-treated anaerobic sludge (ANS) and a mixture of those cultures (MIX). Cumulative hydrogen formation (CHF), hydrogen yield (HY) and specific hydrogen production rate (SHPR) were determined for every culture. The heat-treated anaerobic sludge was found to be the most effective culture with a cumulative hydrogen formation of 560 ml, hydrogen yield of 223 ml H{sub 2} g{sup -1} starch and a specific hydrogen production rate of 32.1 ml H{sub 2} g{sup -1} h{sup -1}. (author)

  20. Direct hydrogen production from cellulosic waste materials with a single-step dark fermentation process

    Energy Technology Data Exchange (ETDEWEB)

    Magnusson, Lauren; Islam, Rumana; Levin, David; Cicek, Nazim [Department of Biosystems Engineering, University of Manitoba, Winnipeg, MB (Canada); Sparling, Richard [Department of Microbiology, University of Manitoba, Winnipeg, MB (Canada)

    2008-10-15

    Biohydrogen production from cellulosic waste materials using dark fermentation is a promising technology for producing renewable energy. The purpose of this study was to evaluate residual cellulosic materials generated from local sources for their H{sub 2} production potential without any pretreatment. Clostridium thermocellum ATCC 27405, a cellulolytic, thermophilic bacterium that has been shown to be capable of H{sub 2} production on both cellobiose and {alpha}-cellulose substrates, was used in simultaneous batch fermentation experiments with dried distillers grain (DDGs), barley hulls (BH) and fusarium head blight contaminated barley hulls (CBH) as the carbon source. Overall, the dried distillers grain produced the highest concentration of hydrogen gas at 1.27 mmol H{sub 2}/glucose equivalent utilized. CBH and BH produced 1.18 and 1.24 mmol H{sub 2}/glucose equivalent utilized, respectively. Overall, this study indicates that hydrogen derived from a variety of cellulosic waste biomass sources is a possible candidate for the development of sustainable energy. (author)

  1. GAT 4 production and storage of hydrogen. Report July 2004; GAT 4 procduction et stockage de l'hydrogene. Rapport juillet 2004

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    This paper concerns two aspects of the hydrogen: the production and the storage. For both parts the challenges and a state of the art are presented. It discusses also the hydrogen production by renewable energies, by solar energy, the hydrogen of hydrocarbons reforming purification, active phases development, thermal transfer simulation. Concerning the hydrogen storage the hydrogen adsorption by large surface solid, the storage by metallic hydrides, the alanates and light hydrides, the adsorption on carbon nano-tubes, the storage in nano-structures, the thermal and mechanical simulation of the hydrogen are presented. (A.L.B.)

  2. Biochemical kinetics of fermentative hydrogen production by Clostridium butyricum W5

    Energy Technology Data Exchange (ETDEWEB)

    Wang, X. [School of Earth and Environmental Sciences, The University of Adelaide, Adelaide, SA 5005 (Australia); Monis, P.T. [Australian Water Quality Centre, SA Water, Bolivar, SA 5110 (Australia); Saint, C.P.; Jin, B. [School of Earth and Environmental Sciences, The University of Adelaide, Adelaide, SA 5005 (Australia)]|[Australian Water Quality Centre, SA Water, Bolivar, SA 5110 (Australia)

    2009-01-15

    The fermentation process for hydrogen production has been widely reported. However, there is lack of information related to detailed kinetic studies. The aim of this work was to investigate biochemical kinetics of fermentative hydrogen production by a newly isolated strain of Clostridium butyricum W5. The research objectives were to clarify relationships between hydrogen fermentation and biochemical parameters and hydrogenases, and consequently to seek an index for hydrogen production. Time profiles of hydrogen production, cell growth, volatile fatty acid accumulation and [FeFe]hydrogenase expression level were described. The amount of hydrogen produced in a laboratory batch process was 45.45 mmol/L at 10 h and peak production rate was 7.61 mmol/l/h at 9 h. Cell growth rate peaked at 8 h. Lactic acid was a main by-product, followed by butyric acid and acetic acid. Quantification of [FeFe]hydrogenase mRNA was optimized by a real-time reverse transcriptase-PCR. Statistical analysis showed that [FeFe]hydrogenase mRNA levels peak earlier than hydrogen production rate, and cell growth has a linear positive relationship with hydrogen production. (author)

  3. Fermentative Hydrogen Production: Influence of Application of Mesophilic and Thermophilic Bacteria on Mass and Energy Balances

    NARCIS (Netherlands)

    Foglia, D.; Wukovits, W.; Friedl, A.; Vrije, de G.J.; Claassen, P.A.M.

    2011-01-01

    Fermentation of biomass residues and second generation biomasses is a possible way to enable a sustainable production of hydrogen. The HYVOLUTION-project investigates the production of hydrogen by a 2-stage fermentation process of biomass. It consists of a dark fermentation step of sugars to produce

  4. Fermentative Hydrogen Production: Influence of Application of Mesophilic and Thermophilic Bacteria on Mass and Energy Balances

    NARCIS (Netherlands)

    Foglia, D.; Wukovits, W.; Friedl, A.; Vrije, de G.J.; Claassen, P.A.M.

    2011-01-01

    Fermentation of biomass residues and second generation biomasses is a possible way to enable a sustainable production of hydrogen. The HYVOLUTION-project investigates the production of hydrogen by a 2-stage fermentation process of biomass. It consists of a dark fermentation step of sugars to produce

  5. Mesophilic and thermophilic alkaline fermentation of waste activated sludge for hydrogen production: Focusing on homoacetogenesis

    DEFF Research Database (Denmark)

    Wan, Jingjing; Jing, Yuhang; Zhang, Shicheng;

    2016-01-01

    The present study compared the mesophilic and thermophilic alkaline fermentation of waste activated sludge (WAS) for hydrogen production with focus on homoacetogenesis, which mediated the consumption of H2 and CO2 for acetate production. Batch experiments showed that hydrogen yield of WAS increased...

  6. Simultaneous cellulose conversion and hydrogen production assisted by cellulose decomposition under UV-light photocatalysis.

    Science.gov (United States)

    Zhang, Guan; Ni, Chengsheng; Huang, Xiubing; Welgamage, Aakash; Lawton, Linda A; Robertson, Peter K J; Irvine, John T S

    2016-01-28

    Photocatalytic conversion of cellulose to sugars and carbon dioxide with simultaneous production of hydrogen assisted by cellulose decomposition under UV or solar light irradiation was achieved upon immobilization of cellulose onto a TiO2 photocatalyst. This approach enables production of hydrogen from water without using valuable sacrificial agents, and provides the possibility for recovering sugars as liquid fuels.

  7. Hydrogen production and ammonium recovery from urine by a Microbial Electrolysis Cell

    NARCIS (Netherlands)

    Kuntke, P.; Sleutels, T.H.J.A.; Saakes, M.; Buisman, C.J.N.

    2014-01-01

    We investigated the use of a Microbial Electrolysis Cell (MEC) for the ammonium removal, COD removal and hydrogen production from five times diluted urine. During operation with a batch cathode, a current density of 23.07 +/- 1.15 A m(-2) was achieved corresponding to a hydrogen production rate of 4

  8. Potential use of thermophilic dark fermentation effluents in photofermentative hydrogen production by Rhodobacter capsulatus

    NARCIS (Netherlands)

    Ozgur, E.; Afsar, N.; Vrije, de G.J.; Yucel, M.; Gunduz, U.; Claassen, P.A.M.; Eroglu, I.

    2010-01-01

    Biological hydrogen production by a sequential operation of dark and photofermentation is a promising route to produce hydrogen. The possibility of using renewable resources, like biomass and agro-industrial wastes, provides a dual effect of sustainability in biohydrogen production and simultaneous

  9. Enzymatic production of hydrogen gas from glucose and cellulose

    Energy Technology Data Exchange (ETDEWEB)

    Mattingly, S.M.; Woodward, J. [Oak Ridge National Lab., TN (United States)

    1996-10-01

    An enzymatic process has been used to convert glucose to molecular hydrogen with the ultimate goal of converting cellulose to hydrogen. Two enzymes from the Archae, Thermoplasma acidophilium glucose dehydrogenase (GDH) and Pyrococcus furiosus hydrogenase, were used to oxidize glucose and NADPH respectively, resulting in the formation of molecular hydrogen. The stoichiometric yield of hydrogen from glucose was close to the theoretical maximum expected. Further, the molar amount of hydrogen produced was greater than the molar equivalent of NADP{sup +} present in the reaction mixture indicating that this GDH cofactor was regenerated throughout the course of the reaction. Hydrogen was also shown to be produced from cellulose if cellulase was included in the reaction mixture.

  10. Selective production of hydrogen peroxide and oxidation of hydrogen sulfide in an unbiased solar photoelectrochemical cell

    DEFF Research Database (Denmark)

    Zong, Xu; Chen, Hongjun; Seger, Brian

    2014-01-01

    A solar-to-chemical conversion process is demonstrated using a photoelectrochemical cell without external bias for selective oxidation of hydrogen sulfide (H2S) to produce hydrogen peroxide (H2O2) and sulfur (S). The process integrates two redox couples anthraquinone/anthrahydroquinone and I−/I3...

  11. Development of a combined bio-hydrogen- and methane-production unit using dark fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Brunstermann, R.; Widmann, R. [Duisburg-Essen Univ. (Germany). Dept. of Urban Water and Waste Management

    2010-07-01

    Hydrogen is regarded as a source of energy of the future. Currently, hydrogen is produced, predominantly, by electrolysis of water by using electricity or by stream reforming of natural gas. So both methods are based on fossil fuels. If the used electricity is recovered from renewable recourses, hydrogen produced by water electrolysis may be a clean solution. At present, the production of hydrogen by biological processes finds more and more attention world far. The biology provides a wide range of approaches to produce hydrogen, including bio-photolysis as well as photo-fermentation and dark-fermentation. Currently these biological technologies are not suitable for solving every day energy problems [1]. But the dark-fermentation is a promising approach to produce hydrogen in a sustainable way and was already examined in some projects. At mesophilic conditions this process provides a high yield of hydrogen by less energy demand, [2]. Short hydraulic retention times (HRT) and high metabolic rates are advantages of the process. The incomplete transformation of the organic components into various organic acids is a disadvantage. Thus a second process step is required. Therefore the well known biogas-technique is used to degrade the organic acids predominantly acetic and butyric acid from the hydrogen-production unit into CH{sub 4} and CO{sub 2}. This paper deals with the development of a combined hydrogen and methane production unit using dark fermentation at mesophilic conditions. The continuous operation of the combined hydrogen and methane production out of DOC loaded sewages and carbohydrate rich biowaste is necessary for the examination of the technical and economical implementation. The hydrogen step shows as first results hydrogen concentration in the biogas between 40 % and 60 %.The operating efficiency of the combined production of hydrogen and methane shall be checked as a complete system. (orig.)

  12. Biological hydrogen production from probiotic wastewater as substrate by selectively enriched anaerobic mixed microflora

    Energy Technology Data Exchange (ETDEWEB)

    Sivaramakrishna, D.; Sreekanth, D.; Himabindu, V. [Centre for Environment, Institute of Science and Technology, Jawaharlal Nehru Technological University, Kukatpally, Hyderabad 500072, Andhra Pradesh (India); Anjaneyulu, Y. [TLGVRC, JSU Box 18739, JSU, Jackson, MS 32917-0939 (United States)

    2009-03-15

    Biohydrogen production from probiotic wastewater using mixed anaerobic consortia is reported in this paper. Batch tests are carried out in a 5.0 L batch reactor under constant mesophillic temperature (37 C). The maximum hydrogen yield 1.8 mol-hydrogen/mol-carbohydrate is obtained at an optimum pH of 5.5 and substrate concentration 5 g/L. The maximum hydrogen production rate is 168 ml/h. The hydrogen content in the biogas is more than 65% and no significant methane is observed throughout the study. In addition to hydrogen, acetate, propionate, butyrate and ethanol are found to be the main by-products in the metabolism of hydrogen fermentation. (author)

  13. Comparison of conventional vs. modular hydrogen refueling stations and on-site production vs. delivery.

    Energy Technology Data Exchange (ETDEWEB)

    Hecht, Ethan S. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Pratt, Joseph William [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2017-03-01

    To meet the needs of public and private stakeholders involved in the development, construction, and operation of hydrogen fueling stations needed to support the widespread roll-out of hydrogen fuel cell electric vehicles, this work presents publicly available station templates and analyses. These ‘Reference Stations’ help reduce the cost and speed the deployment of hydrogen stations by providing a common baseline with which to start a design, enable quick assessment of potential sites for a hydrogen station, identify contributors to poor economics, and suggest areas of research. This work presents layouts, bills of materials, piping and instrumentation diagrams, and detailed analyses of five new station designs. In the near term, delivered hydrogen results in a lower cost of hydrogen compared to on-site production via steam methane reforming or electrolysis, although the on-site production methods have other advantages. Modular station concepts including on-site production can reduce lot sizes from conventional assemble-on-site stations.

  14. Prospects of utilization of sugar beet carbohydrates for biological hydrogen production in the EU

    Energy Technology Data Exchange (ETDEWEB)

    Panagiotopoulos, J.A.; Koukios, E.G. [Bioresource Technology Unit, School of Chemical Engineering, National Technical University of Athens, Zografou Campus, Athens, GR-15700 (Greece); Bakker, R.R.; De Vrije, T.; Claassen, P.A.M. [Wageningen UR Agrotechnology and Food Innovations, P.O. Box 17, 6700 AA Wageningen (Netherlands); Urbaniec, K. [CERED Centre of Excellence, Warsaw University of Technology, Jachowicza 2/4, 09-402 Plock (Poland)

    2010-12-15

    Hydrogen can be produced through dark anaerobic fermentation using carbohydrate-rich biomass, and through photofermentation using the organic acids produced from dark fermentation. Sugar beet is an ideal energy crop for fermentative production of hydrogen in the EU due to its environmental profile and its potential availability in the area. In this work, various aspects of cultivating sugar beet in the EU for biohydrogen were highlighted, with special focus on The Netherlands and Greece. Moreover, fermentation of sugar beet juice with Caldicellulosiruptor saccharolyticus at sucrose concentration 10 g/l was performed, and was found comparable to the fermentation on pure sucrose except that the hydrogen production was 10% higher on sugar beet juice. A conservative estimate of the annual hydrogen potential in the EU was made (300x10{sup 6} kg hydrogen), considering the utilization of sugar beet pulp in hydrogen production.

  15. Steam reforming of propane in a fluidized bed membrane reactor for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Rakib, Mohammad A.; Grace, John R.; Lim, C. Jim; Ghiasi, Bahman [Department of Chemical and Biological Engineering, University of British Columbia, 2360 East Mall, Vancouver BC (Canada); Elnashaie, Said S.E.H. [College of Engineering, Misr University for Science and Technology, Distinguished District, 6th of October Province (Egypt)

    2010-06-15

    Steam reforming of propane was carried out in a fluidized bed membrane reactor to investigate a feedstock other than natural gas for production of pure hydrogen. Close to equilibrium conditions were achieved inside the reactor with fluidized catalyst due to the very fast steam reforming reactions. Use of hydrogen permselective Pd{sub 77}Ag{sub 23} membrane panels to extract pure hydrogen shifted the reaction towards complete conversion of the hydrocarbons, including methane, the key intermediate product. Irreversible propane steam reforming is limited by the reversibility of the steam reforming of this methane. To assess the performance improvement due to pure hydrogen withdrawal, experiments were conducted with one and six membrane panels installed along the height of the reactor. The results indicate that a compact reformer can be achieved for pure hydrogen production for a light hydrocarbon feedstock like propane, at moderate operating temperatures of 475-550 C, with increased hydrogen yield. (author)

  16. Updated hydrogen production costs and parities for conventional and renewable technologies

    Energy Technology Data Exchange (ETDEWEB)

    Lemus, Ricardo Guerrero [Fundacion de Estudios de Economia Aplicada (Programa Focus-Abengoa), Jorge Juan, 46, 28001 Madrid (Spain); Departamento de Fisica Basica, Universidad de La Laguna, Avda. Astrofisico Francisco Sanchez, 38204 La Laguna, S/C de Tenerife (Spain); Martinez Duart, Jose Manuel [Fundacion de Estudios de Economia Aplicada (Programa Focus-Abengoa), Jorge Juan, 46, 28001 Madrid (Spain); Instituto de Ciencia de Materiales Nicolas Cabrera, Campus de Cantoblanco, modulo C-XVI, 28049 Madrid (Spain)

    2010-05-15

    This paper provides first a review of the production costs of hydrogen from conventional, nuclear and renewable sources, reported in the literature during the last eight years. In order to analyze the costs on a unified basis, they are updated to a common year (2009), taking into account the yearly inflation rates. The study also considers whether the hydrogen has been produced in centralized or distributed facilities. From these data, the expected future costs for conventional production of hydrogen are calculated considering several scenarios on carbon emission taxations. Based on these estimations, together with the predicted future costs (2019-2020 and 2030) for hydrogen from alternative sources, several hydrogen cost-parity analyses are exposed for renewable and nuclear energies. From the comparison between these alternative technologies for hydrogen production and the conventional ones (steam methane reforming and coal gasification), several predictions on the time-periods to reach cost parities are elaborated. (author)

  17. Recent trends on the development of photobiological processes and photobioreactors for the improvement of hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Dasgupta, Chitralekha Nag; Jose Gilbert, J.; Das, Debabrata [Department of Biotechnology, Indian Institute of Technology, Kharagpur 721302 (India); Lindblad, Peter; Heidorn, Thorsten [Department of Photochemistry and Molecular Science, Uppsala University (Sweden); Borgvang, Stig A.; Skjanes, Kari [Norwegian Institute for Agricultural and Environmental Research (Bioforsk), Oslo (Norway)

    2010-10-15

    Hydrogen production through biological routes is promising because they are environmentally friendly. Hydrogen production through biophotolysis or photofermentation is usually a two stage process. In the first stage CO{sub 2} is utilized for biomass production which is followed by hydrogen production in the second stage in anaerobic/sulfur-deprived conditions. In addition, one-stage photobiological hydrogen production process can be achieved using selected cyanobacterial strains. The major challenges confronting the large scale production of biomass/hydrogen are limited not only on the performance of the photobioreactors in which light penetration in dense cultures is a major bottleneck but also on the characteristics of the organisms. Other dependable factors include area/volume (A/V) ratio, mode of agitation, temperature and gas exchange. Photobioreactors of different geometries are reported for biohydrogen production: Tubular, Flat plate, Fermentor type etc. Every reactor has its own advantages and disadvantages. Airlift, helical tubular and flat plate reactors are found most suitable with respect to biomass production. These bioreactors may be employed for hydrogen production with necessary modifications to overcome the existing bottlenecks like gas hold up, oxygen toxicity and poor agitation. This review article attempts to focus on existing photobioreactors with respect to biomass generation and hydrogen production and the steps taken to improve its performance through engineering innovation that definitely help in the future design and construction of photobioreactors. (author)

  18. Techno-economic evaluation of a combined bioprocess for fermentative hydrogen production from food waste.

    Science.gov (United States)

    Han, Wei; Fang, Jun; Liu, Zhixiang; Tang, Junhong

    2016-02-01

    In this study, the techno-economic evaluation of a combined bioprocess based on solid state fermentation for fermentative hydrogen production from food waste was carried out. The hydrogen production plant was assumed to be built in Hangzhou and designed for converting 3 ton food waste per day into hydrogen. The total capital cost (TCC) and the annual production cost (APC) were US$583092 and US$88298.1/year, respectively. The overall revenue after the tax was US$146473.6/year. The return on investment (ROI), payback period (PBP) and internal rate of return (IRR) of the plant were 26.75%, 5 years and 24.07%, respectively. The results exhibited that the combined bioprocess for hydrogen production from food waste was feasible. This is an important study for attracting investment and industrialization interest for hydrogen production from food waste in the industrial scale.

  19. Kinetic modeling and experimental studies of hydrogen production by non-equilibrium plasma discharge decomposition of methane and other hydrogen-containing species

    Energy Technology Data Exchange (ETDEWEB)

    Boutot, T.; Liu, Z. [Atlantic Hydrogen Inc., Fredericton, NB (Canada); Whidden, T.K.; Yang, Y. [New Brunswick Univ., Fredericton, NB (Canada)

    2007-07-01

    Hydrogen as an energy source is an option that is being explored in order to reduce anthropogenic greenhouse gas (GHG) emissions. In particular, proton exchange membrane (PEM) fuel cells using hydrogen and emitting no GHGs are under global development. The long-term production process of choice is hydrogen derived directly from water. However, hydrogen from electrolysis is not economically viable and bridging technologies for green hydrogen production must be found. Any new technology for hydrogen production should also accommodate the fact that no infrastructure for the widespread distribution of pure hydrogen exists. Hydrogen production technologies that leverage existing infrastructure for delivery will therefore have a significant economic advantage. This paper described the anaerobic high frequency pulsed plasma pyrolysis of methane using a proprietary reactor system. The paper discussed modeling studies and progress in scaling this reactor to pilot scale operation. It also discussed several experiments on using the system for the dissociation of another hydrogen source, hydrogen sulphide (H2{sub S}). Hydrogen and solid carbon were produced for methane or natural gas as the feedstock. The prototype bench-scale process was scaled to near pilot-scale, treating significant flows of natural gas. Long term data on system performance at conversions producing 20 per cent hydrogen in natural gas as the product were presented. Chemical kinetic models for the dissociation process and characterizational data for the solid carbon product were presented. 48 refs., 2 tabs., 9 figs.

  20. Hydrogen production from sugars and sweet sorghum biomass using Ruminococcus albus

    Energy Technology Data Exchange (ETDEWEB)

    Ntaikou, I.; Gavala, H.N.; Lyberatos, G. [Department of Chemical Engineering, University of Patras, Karatheodori 1 st., 26500 Patras (Greece); Institute of Chemical Engineering and High Temperature Chemical Processes, 26504 Patras (Greece); Kornaros, M. [Department of Chemical Engineering, University of Patras, Karatheodori 1 st., 26500 Patras (Greece)

    2008-02-15

    In the present work the production of hydrogen from sorghum biomass by pure cultures of the bacterium Ruminococcus albus was investigated. R. albus, an important fibrolytic bacterium of the rumen, can ferment hexoses and pentoses as well as cellulose and hemicelluloses. Therefore, R. albus seems to be very promising for the production of hydrogen from energy crops such as sweet sorghum, with the potential of utilizing not only the free sugars but also the cellulosic/hemicellulosic biomass as well. Batch and continuous stirred tank reactor (CSTR) experiments were carried out using glucose as carbon source in order to investigate the metabolism and calculate the growth kinetics of R. albus. Besides hydrogen, the main metabolic products detected were acetic and formic acids and ethanol. Hydrogen yield ranged from 0.47 to 2.52 mol of hydrogen per mole of glucose in continuous and batch experiments, respectively. Moreover, sorghum water extract containing soluble sugars and the lignocellulosic sorghum biomass before and after water extraction were also tested as potential substrates for hydrogen production using R. albus. The hydrogen productivity of sorghum extract plus that of sorghum residues equaled the hydrogen productivity obtained from the sorghum stalks suggesting that the process could be designed as a single-step process, thus avoiding the separate fermentation of soluble and insoluble carbohydrates as well as the extraction process. Hydrogen productivity has been estimated to be approximately 60 l of hydrogen per kg of wet sorghum biomass, thus suggesting that R. albus is suitable for efficient hydrogen production from sweet sorghum biomass. (author)

  1. High yield hydrogen production in a single-chamber membrane-less microbial electrolysis cell.

    Science.gov (United States)

    Ye, Yejie; Wang, Liyong; Chen, Yingwen; Zhu, Shemin; Shen, Shubao

    2010-01-01

    The single-chamber membrane-less MEC exerted much better hydrogen production performance while given higher applied voltages than it did at lower. High applied voltages that could shorten the reaction time and the exposure of anode to air for at least 30 min between cycles can significantly suppress methanogen and increase hydrogen production. At an applied voltage of 1.0 V, a hydrogen production rate of 1.02 m(3)/m(3)/day with a current density of 5.7 A/m(2) was achieved. Cathodic hydrogen recovery and coulombic efficiency were 63.4% and 69.3% respectively. The hydrogen concentration of mixture gas produced of 98.4% was obtained at 1.0 V, which was the best result of reports. The reasons that such a high hydrogen concentration can be achieved were probably the high electrochemical activity and hydrogen production capability of the active microorganisms. Increase in substrate concentrations could not improve MEC's performance, but increased the reaction times. Further, reactor configuration and operation factors optimisation should be considered to increase current density, hydrogen production rate and hydrogen recovery.

  2. Temperature effects on fermentative hydrogen production from xylose using mixed anaerobic cultures

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Chiu-Yue; Wu, Chein-Chung [BioHydrogen Laboratory, Department of Water Resource Engineering, Feng Chia University, P.O. Box 25-123, Taichung 40724 (China); Hung, Chun-Hsiung [Department of Environmental Engineering, National Chung-Hsing University, 250 Kuo-Kuang Road, Taichung 40227 (China)

    2008-01-15

    Sewage sludge microflora were anaerobically cultivated in a chemostat-type anaerobic bioreactor at temperatures of 30-55{sup o}C, a pH of 7.1 and a hydraulic retention time of 12 h to determine the hydrogen production efficiency from xylose (20 g-COD/L). It was demonstrated that hydrogen production of the enriched sewage sludge microflora (dominated by Clostridia species) was temperature-dependent in hydrogen gas content, hydrogen yield, hydrogen production rate (HPR) and specific HPR with values of 25.1-42.2% (v/v), 0.4-1.4 mol-H{sub 2}/mol-xylose, 0.06-0.24 mol-H{sub 2}/L-day and 0.02-0.10 mol-H{sub 2}/g-VSS-day, respectively, and the above values peaked whaaen being operated at 50{sup o}C. A transition temperature of 45{sup o}C existed by having a lowest hydrogen production efficiency. Butyrate and ethanol were the major soluble metabolite products for thermophilic and mesophilic fermentation, respectively. The liquid metabolite concentration fractions and microbial community analysis indicate that the differences in hydrogen production efficiency between each tested temperature might relate to the shifts in metabolic pathway or microbial community. Thermodynamic analysis using HPR values and Arrhenius equation showed that the activation energy was 74.7 kJ/mol. Strategies based on temperature control for optimal hydrogen production from xylose using natural mixed cultures are proposed. (author)

  3. System for the co-production of electricity and hydrogen

    Science.gov (United States)

    Pham, Ai Quoc; Anderson, Brian Lee

    2007-10-02

    Described herein is a system for the co-generation of hydrogen gas and electricity, wherein the proportion of hydrogen to electricity can be adjusted from 0% to 100%. The system integrates fuel cell technology for power generation with fuel-assisted steam-electrolysis. A hydrocarbon fuel, a reformed hydrocarbon fuel, or a partially reformed hydrocarbon fuel can be fed into the system.

  4. Enhanced Process for Methanol Production by CO2 Hydrogenation

    NARCIS (Netherlands)

    Kiss, Anton Alexandru; Pragt, J.J.; Vos, H.J.; Bargeman, Gerrald; de Groot, M.T.

    2016-01-01

    In the quest for a green chemical industry, much effort is devoted to the development of technologies for methanol synthesis by hydrogenation of CO2 – available from many sources. Low-cost sources of H2 are less frequently found, but an additional source at industrial scale is the wet hydrogen

  5. Enhanced Process for Methanol Production by CO2 Hydrogenation

    NARCIS (Netherlands)

    Kiss, Anton A.; Pragt, J.J.; Vos, H.J.; Bargeman, G.; Groot, de M.T.

    2016-01-01

    In the quest for a green chemical industry, much effort is devoted to the development of technologies for methanol synthesis by hydrogenation of CO2 – available from many sources. Low-cost sources of H2 are less frequently found, but an additional source at industrial scale is the wet hydrogen by-pr

  6. Study on Production of Hydrogen from Methane for Proton Exchange Membrane Fuel Cell

    Institute of Scientific and Technical Information of China (English)

    宋正昶; 李传统

    2001-01-01

    The hydrogen production from methane for proton exchange membrane fuel cell (PEMFC) was studied experimentally. The conversion rate of methane under different steam-carbon ratios, the effect of the different excess air ratios on the constituents of the gas produced, the permeability of hydrogen under different pressure differences, and the effect of different system pressure on the reaction enthalpy of hydrogen were obtained. The results lay the basis for the production of hydrogen applicable to PEMFC, moreover, provide a new way for the comprehensive utilization of the coal bed methane.

  7. Management of Leaks in Hydrogen Production, Delivery, and Storage Systems

    Energy Technology Data Exchange (ETDEWEB)

    Rawls, G

    2006-04-27

    A systematic approach to manage hydrogen leakage from components is presented. Methods to evaluate the quantity of hydrogen leakage and permeation from a system are provided by calculation and testing sensitivities. The following technology components of a leak management program are described: (1) Methods to evaluate hydrogen gas loss through leaks; (2) Methods to calculate opening areas of crack like defects; (3) Permeation of hydrogen through metallic piping; (4) Code requirements for acceptable flammability limits; (5) Methods to detect flammable gas; (6) Requirements for adequate ventilation in the vicinity of the hydrogen system; (7) Methods to calculate dilution air requirements for flammable gas mixtures; and (8) Concepts for reduced leakage component selection and permeation barriers.

  8. Sorption enhanced reaction process (SERP) for the production of hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Hufton, J.; Mayorga, S.; Gaffney, T.; Nataraj, S.; Rao, M.; Sircar, S. [Air Products and Chemicals, Inc., Allentown, PA (United States)

    1998-08-01

    The novel Sorption Enhanced Reaction Process has the potential to decrease the cost of hydrogen production by steam methane reforming. Current effort for development of this technology has focused on adsorbent development, experimental process concept testing, and process development and design. A preferred CO{sub 2} adsorbent, K{sub 2}CO{sub 3} promoted hydrotalcite, satisfies all of the performance targets and it has been scaled up for process testing. A separate class of adsorbents has been identified which could potentially improve the performance of the H{sub 2}-SER process. Although this material exhibits improved CO{sub 2} adsorption capacity compared to the HTC adsorbent, its hydrothermal stability must be improved. Single-step process experiments (not cyclic) indicate that the H{sub 2}-SER reactor performance during the reaction step improves with decreasing pressure and increasing temperature and steam to methane ratio in the feed. Methane conversion in the H{sub 2}-SER reactor is higher than for a conventional catalyst-only reactor operated at similar temperature and pressure. The reactor effluent gas consists of 90+% H{sub 2}, balance CH{sub 4}, with only trace levels (< 50 ppm) of carbon oxides. A best-case process design (2.5 MMSCFD of 99.9+% H{sub 2}) based on the HTC adsorbent properties and a revised SER process cycle has been generated. Economic analysis of this design indicates the process has the potential to reduce the H{sub 2} product cost by 25--31% compared to conventional steam methane reforming.

  9. Glycerol and bioglycerol conversion in supercritical water for hydrogen production.

    Science.gov (United States)

    Yu-Wu, Q M; Weiss-Hortala, E; Barna, R; Boucard, H; Bulza, S

    2012-01-01

    Catalytic transesterification of vegetable oils leads to biodiesel and an alkaline feed (bioglycerol and organic residues, such as esters, alcohols. . .). The conversion ofbioglycerol into valuable organic molecules represents a sustainable industrial process leading to the valorization of a renewable organic resource. The physicochemical properties in the supercritical domain (T > 374 degrees C, P > 22.1 MPa) transform water into a solvent for organics and a reactant favouring radical reactions. In this context, the conversion ofbioglycerol in supercritical water (SCW) into platform molecules and/or high energetic gases (hydrogen, hydrocarbons) could represent an interesting valorization process. The reported research results concern the conversion of bioglycerol compared to pure glycerol. The experiments have been done in batch autoclaves (5 ml and 500 ml stirred). Solutions of pure (5 or 10 wt%) and crude (3.5 wt%) glycerol have been processed with or without catalyst (K2CO3 1.5 wt%) in the range of 450-600 degrees C. The molecular formula of bioglycerol was determined as C4.3H9.7O1.8Na0.1Si0.08. Glycerol was partially decomposed in the batch systems during the heating (42% before reaching 420 degrees C) and some intermediates (propanediol, ethylene glycol . . .) were quantified, leading to a proposition of a reaction pathway. Acrolein, a valuable platform molecule, was mainly produced in the absence of catalyst. No solid phase was recovered after SCW conversion of pure and bioglycerol in batch reactors. The optimal parameters for gasification were 600 degrees C, 25 MPa for bioglycerol and 525 degrees C, 25 MPa, for pure glycerol. In these operating conditions, 1 kg of pure or bioglycerol leads to 15 and, respectively, 10 mol of hydrogen. Supercritical water gasification of crude glycerol favoured the generation of light hydrocarbons, while pure glycerol promoted H2 production. SCW conversion of glycerol (pure and crude) allows to obtain simultaneously energetic

  10. Hydrogen Peroxide as a Sustainable Energy Carrier: Electrocatalytic Production of Hydrogen Peroxide and the Fuel Cell

    OpenAIRE

    Fukuzumi, Shunichi; Yamada, Yusuke; Karlin, Kenneth D.

    2012-01-01

    This review describes homogeneous and heterogeneous catalytic reduction of dioxygen with metal complexes focusing on the catalytic two-electron reduction of dioxygen to produce hydrogen peroxide. Whether two-electron reduction of dioxygen to produce hydrogen peroxide or four-electron O2-reduction to produce water occurs depends on the types of metals and ligands that are utilized. Those factors controlling the two processes are discussed in terms of metal-oxygen intermediates involved in the ...

  11. Comparative study of thermochemical processes for hydrogen production from biomass fuels.

    Science.gov (United States)

    Biagini, Enrico; Masoni, Lorenzo; Tognotti, Leonardo

    2010-08-01

    Different thermochemical configurations (gasification, combustion, electrolysis and syngas separation) are studied for producing hydrogen from biomass fuels. The aim is to provide data for the production unit and the following optimization of the "hydrogen chain" (from energy source selection to hydrogen utilization) in the frame of the Italian project "Filiera Idrogeno". The project focuses on a regional scale (Tuscany, Italy), renewable energies and automotive hydrogen. Decentred and small production plants are required to solve the logistic problems of biomass supply and meet the limited hydrogen infrastructures. Different options (gasification with air, oxygen or steam/oxygen mixtures, combustion, electrolysis) and conditions (varying the ratios of biomass and gas input) are studied by developing process models with uniform hypothesis to compare the results. Results obtained in this work concern the operating parameters, process efficiencies, material and energetic needs and are fundamental to optimize the entire hydrogen chain.

  12. Modeling of hydrogen sulfide oxidation in concrete corrosion products from sewer pipes.

    Science.gov (United States)

    Jensen, Henriette Stokbro; Nielsen, Asbjørn Haaning; Hvitved-Jacobsen, Thorkild; Vollertsen, Jes

    2009-04-01

    Abiotic and biotic oxidation of hydrogen sulfide related to concrete corrosion was studied in corrosion products originating from a sewer manhole. The concrete corrosion products were suspended in an acidic solution, mimicking the conditions in the pore water of corroded concrete. The removal of hydrogen sulfide and dissolved oxygen was measured in parallel in the suspension, upon which the suspension was sterilized and the measurement repeated. The results revealed the biotic oxidation to be fast compared with the abiotic oxidation. The stoichiometry of the hydrogen sulfide oxidation was evaluated using the ratio between oxygen and hydrogen sulfide uptake. The ratio for the biotic oxidation pointed in the direction of elemental sulfur being formed as an intermediate in the oxidation of hydrogen sulfide to sulfuric acid. The experimental results were applied to suggest a hypothesis and a mathematical model describing the hydrogen sulfide oxidation pathway in a matrix of corroded concrete.

  13. Experimental study of hydrogen kinetics from agroindustrial by-product: optimal conditions for production and fuel cell feeding

    Energy Technology Data Exchange (ETDEWEB)

    Perego, P.; Fabiano, B.; Ponzano, G.P.; Palazzi, E. [Univ. Genoa, Inst. of Chemical and Process Engineering ``G.B. Bonino`` (Italy)

    1998-09-01

    One of the best and cleanest systems to produce electric energy is represented by fuel cells, whose natural fuel is hydrogen. In this paper, the production of hydrogen rich biogas is studied. This process contributes to create a system for biomass recovery, which eliminates organic pollutants and produces energy with high efficiency without atmospheric emissions. The study has been based on Escherichia coli and Enterobacter aerogenes strains. The research deals with batch reactors and verification of optimal conditions of hydrogen production. The realization of the optimal working conditions would conduce to the realization of a reactor suitable to feed a stack of the above mentioned fuel cells. In view of industrial applications, some different ways have been considered to greatly enhance the process performance, in terms of rate of hydrogen production, efficiency of hydrogen utilization and/or biosynthesis of valuable subproducts. (orig.)

  14. Magnesium improves hydrogen production by a novel fermentative hydrogen-producing bacterial strain B49

    Institute of Scientific and Technical Information of China (English)

    WANG Xiang-jing; REN Nan-qi; XIANG Wen-sheng

    2005-01-01

    Batch experiments were conducted to investigate the effects of magnesium on glucose metabolism, including growth and hydrogen-producing capacity of fermentative hydrogen-producing bacterial strain B49. These abilities were enhanced with an increase in magnesium concentration. At the end of fermentation from 10 g/L ratio of ethanol amount (mg/L) to acetate amount (mg/L) was 1.1, and the accumulated hydrogen volume hydrogen volume was increased to 2 360. 5 mL H2/L culture, the ratio of ethanol amount (mg/L) to acetate amount (mg/L) was increased to 1.3 and polysaccharide was decreased to 2. 5 mg/L. Moreover, the magnesium solution addition to the medium at different fermentation times affected hydrogen-producing ability. However,the later the addition time was postponed, the less the effect was on hydrogen evolution. Further experiments confirmed the enhancement was dependent on magnesium ions and not on the other inorganic ions such as SO42- or Cl-, which constituted the magnesium salts.

  15. Production of hydrogen in non oxygen-evolving systems: co-produced hydrogen as a bonus in the photodegradation of organic pollutants and hydrogen sulfide

    Energy Technology Data Exchange (ETDEWEB)

    Sartoretti, C. Jorand; Ulmann, M.; Augustynski, J. (Electrochemistry Laboratory, Department of Chemistry, University of Geneva (CH)); Linkous, C.A. (Florida Solar Energy Center, University of Central Florida (US))

    2000-01-01

    This report was prepared as part of the documentation of Annex 10 (Photoproduction of Hydrogen) of the IEA Hydrogen Agreement. Subtask A of this Annex concerned photo-electrochemical hydrogen production, with an emphasis on direct water splitting. However, studies of non oxygen-evolving systems were also included in view of their interesting potential for combined hydrogen production and waste degradation. Annex 10 was operative from 1 March 1995 until 1 October 1998. One of the collaborative projects involved scientists from the Universities of Geneva and Bern, and the Federal Institute of Technology in Laussane, Switzerland. A device consisting of a photoelectrochemical cell (PEC) with a WO{sub 3} photoanode connected in series with a so-called Grazel cell (a dye sensitized liquid junction photovoltaic cell) was developed and studied in this project. Part of these studies concerned the combination of hydrogen production with degradation of organic pollutants, as described in Chapter 3 of this report. For completeness, a review of the state of the art of organic waste treatment is included in Chapter 2. Most of the work at the University of Geneva, under the supervision of Prof. J. Augustynski, was focused on the development and testing of efficient WO{sub 3} photoanodes for the photoelectrochemical degradation of organic waste solutions. Two types of WO{sub 3} anodes were developed: non transparent bulk photoanodes and non-particle-based transparent film photoanodes. Both types were tested for degradation and proved to be very efficient in dilute solutions. For instance, a solar-to-chemical energy conversion efficiency of 9% was obtained by operating the device in a 0.01M solution of methanol (as compared to about 4% obtained for direct water splitting with the same device). These organic compounds are oxidized to CO{sub 2} by the photocurrent produced by the photoanode. The advantages of this procedure over conventional electrolytic degradation are that much (an

  16. HYDROGEN PRODUCTION AND DELIVERY INFRASTRUCTURE AS A COMPLEX ADAPTIVE SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Tolley, George S

    2010-06-29

    An agent-based model of the transition to a hydrogen transportation economy explores influences on adoption of hydrogen vehicles and fueling infrastructure. Attention is given to whether significant penetration occurs and, if so, to the length of time required for it to occur. Estimates are provided of sensitivity to numerical values of model parameters and to effects of alternative market and policy scenarios. The model is applied to the Los Angeles metropolitan area In the benchmark simulation, the prices of hydrogen and non-hydrogen vehicles are comparable. Due to fuel efficiency, hydrogen vehicles have a fuel savings advantage of 9.8 cents per mile over non-hydrogen vehicles. Hydrogen vehicles account for 60% of new vehicle sales in 20 years from the initial entry of hydrogen vehicles into show rooms, going on to 86% in 40 years and reaching still higher values after that. If the fuel savings is 20.7 cents per mile for a hydrogen vehicle, penetration reaches 86% of new car sales by the 20th year. If the fuel savings is 0.5 cents per mile, market penetration reaches only 10% by the 20th year. To turn to vehicle price difference, if a hydrogen vehicle costs $2,000 less than a non-hydrogen vehicle, new car sales penetration reaches 92% by the 20th year. If a hydrogen vehicle costs $6,500 more than a non-hydrogen vehicle, market penetration is only 6% by the 20th year. Results from other sensitivity runs are presented. Policies that could affect hydrogen vehicle adoption are investigated. A tax credit for the purchase of a hydrogen vehicle of $2,500 tax credit results in 88% penetration by the 20th year, as compared with 60% in the benchmark case. If the tax credit is $6,000, penetration is 99% by the 20th year. Under a more modest approach, the tax credit would be available only for the first 10 years. Hydrogen sales penetration then reach 69% of sales by the 20th year with the $2,500 credit and 79% with the $6,000 credit. A carbon tax of $38 per metric ton is not

  17. Economic comparison of hydrogen production using sulfuric acid electrolysis and sulfur cycle water decomposition. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Farbman, G.H.; Krasicki, B.R.; Hardman, C.C.; Lin, S.S.; Parker, G.H.

    1978-06-01

    An evaluation of the relative economics of hydrogen production using two advanced techniques was performed. The hydrogen production systems considered were the Westinghouse Sulfur Cycle Water Decomposition System and a water electrolysis system employing a sulfuric acid electrolyte. The former is a hybrid system in which hydrogen is produced in an electrolyzer which uses sulfur dioxide to depolarize the anode. The electrolyte is sulfuric acid. Development and demonstration efforts have shown that extremely low cell voltages can be achieved. The second system uses a similar sulfuric acid electrolyte technology in water electrolysis cells. The comparative technoeconomics of hydrogen produced by the hybrid Sulfur Cycle and by water electrolysis using a sulfuric acid electrolyte were determined by assessing the performance and economics of 380 million SCFD plants, each energized by a very high temperature nuclear reactor (VHTR). The evaluation concluded that the overall efficiencies of hydrogen production, for operating parameters that appear reasonable for both systems, are approximately 41% for the sulfuric acid electrolysis and 47% for the hybrid Sulfur Cycle. The economic evaluation of hydrogen production, based on a 1976 cost basis and assuming a developed technology for both hydrogen production systems and the VHTRs, indicated that the hybrid Sulfur Cycle could generate hydrogen for a total cost approximately 6 to 7% less than the cost from the sulfuric acid electrolysis plant.

  18. Nano-ferrites for water splitting: Unprecedented high photocatalytic hydrogen production under visible light

    KAUST Repository

    Mangrulkar, Priti A.

    2012-01-01

    In the present investigation, hydrogen production via water splitting by nano-ferrites was studied using ethanol as the sacrificial donor and Pt as co-catalyst. Nano-ferrite is emerging as a promising photocatalyst with a hydrogen evolution rate of 8.275 μmol h -1 and a hydrogen yield of 8275 μmol h -1 g -1 under visible light compared to 0.0046 μmol h -1 for commercial iron oxide (tested under similar experimental conditions). Nano-ferrites were tested in three different photoreactor configurations. The rate of hydrogen evolution by nano-ferrite was significantly influenced by the photoreactor configuration. Altering the reactor configuration led to sevenfold (59.55 μmol h -1) increase in the hydrogen evolution rate. Nano-ferrites have shown remarkable stability in hydrogen production up to 30 h and the cumulative hydrogen evolution rate was observed to be 98.79 μmol h -1. The hydrogen yield was seen to be influenced by several factors like photocatalyst dose, illumination intensity, irradiation time, sacrificial donor and presence of co-catalyst. These were then investigated in detail. It was evident from the experimental data that nano-ferrites under optimized reaction conditions and photoreactor configuration could lead to remarkable hydrogen evolution activity under visible light. Temperature had a significant role in enhancing the hydrogen yield. © 2012 The Royal Society of Chemistry.

  19. Integrated analysis of transportation demand pathway options for hydrogen production, storage, and distribution

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, C.E.S. [Directed Technologies Inc., Arlington, VA (United States)

    1996-10-01

    Directed Technologies, Inc. has begun the development of a computer model with the goal of providing guidance to the Hydrogen Program Office regarding the most cost effective use of limited resources to meet national energy security and environmental goals through the use of hydrogen as a major energy carrier. The underlying assumption of this programmatic pathway model is that government and industry must work together to bring clean hydrogen energy devices into the marketplace. Industry cannot provide the long term resources necessary to overcome technological, regulatory, institutional, and perceptual barriers to the use of hydrogen as an energy carrier, and government cannot provide the substantial investments required to develop hydrogen energy products and increased hydrogen production capacity. The computer model recognizes this necessary government/industry partnership by determining the early investments required by government to bring hydrogen energy end uses within the time horizon and profitability criteria of industry, and by estimating the subsequent investments required by industry. The model then predicts the cost/benefit ratio for government, based on contributions of each hydrogen project to meeting societal goals, and it predicts the return on investment for industry. Sensitivity analyses with respect to various government investments such as hydrogen research and development and demonstration projects will then provide guidance as to the most cost effective mix of government actions. The initial model considers the hydrogen transportation market, but this programmatic pathway methodology will be extended to other market segments in the future.

  20. Techno-economic Analysis of Distributed Hydrogen Production from Natural Gas

    Institute of Scientific and Technical Information of China (English)

    LUK Ho Ting; LEI Ho Man; NG Wai Yee; JU Yihan; LAM Koon Fung

    2012-01-01

    It is well established that hydrogen has the potential to make a significant contribution to the world energy production. In U.S., majority of hydrogen production plants implement steam methane reforming (SMR) for centralized hydrogen production. However, there is a wide lack of agreement on the nascent stage of using hydro- gen as fuel in vehicles industry because of the difficulty in delivery and storage. By performing technological and economic analysis, this work aims to establish the most feasible hydrogen production pathway for automotives in near future. From the evaluation, processes such as thermal cracking of ammonia and centralized hydrogen production followed by bulk delivery are eliminated while on-site steam reforming of methanol and natural gas are the most technologically feasible options. These two processes are further evaluated by comprehensive economic analysis. The results showed that the steam reforming (SR) of natural gas has a shorter payback time and a higher return on investment (ROI) and internal rate of return (IRR). Sensitivity analysis has also been constructed to evaluate the impact of variables like NG feedstock price, capital of investment and operating capacity factor on the overall production cost of hydrogen. Based on this study, natural gas is prompted to be the most economically and technologically available raw material for short-term hydrogen production before the transition to renewable energy source such as solar energy, biomass and wind power.

  1. Hydrogen and methane production from household solid waste in the two-stage fermentation process.

    Science.gov (United States)

    Liu, Dawei; Liu, Dapeng; Zeng, Raymond J; Angelidaki, Irini

    2006-06-01

    A two-stage process combined hydrogen and methane production from household solid waste was demonstrated working successfully. The yield of 43 mL H(2)/g volatile solid (VS) added was generated in the first hydrogen production stage and the methane production in the second stage was 500 mL CH(4)/g VS added. This figure was 21% higher than the methane yield from the one-stage process, which was run as control. Sparging of the hydrogen reactor with methane gas resulted in doubling of the hydrogen production. pH was observed as a key factor affecting fermentation pathway in hydrogen production stage. The optimum pH range for hydrogen production in this system was in the range from 5 to 5.5. The short hydraulic retention time (2 days) applied in the first stage was enough to separate acidogenesis from methanogenesis. No additional control for preventing methanogenesis in the first stage was necessary. Furthermore, this study also provided direct evidence in the dynamic fermentation process that, hydrogen production increase was reflected by acetate to butyrate ratio increase in liquid phase.

  2. Inhibitory effects of butyrate on biological hydrogen production with mixed anaerobic cultures.

    Science.gov (United States)

    Zheng, Xian-Jun; Yu, Han-Qing

    2005-01-01

    In this study batch experiments were conducted to investigate the inhibitory effects of butyrate addition on hydrogen production from glucose by using anaerobic mixed cultures. Experimental results showed that addition of butyrate at 4.18 and 6.27 g/l only slightly inhibited hydrogen production, and addition of butyrate at 8.36-12.54 g/l imposed a moderate inhibitory effect on hydrogen production. At addition of 25.08 g/l, butyrate had a strong inhibitory influence on substrate degradation and hydrogen production. The distribution of the volatile fatty acids produced from the acidogeneisis of glucose was significantly influenced by the addition of butyrate. The inhibition of butyrate addition on hydrogen production was described well by a non-competitive and non-linear inhibition model, with the maximum hydrogen production rate of 59.3 ml/g-SS/h, critical added butyrate concentration of 25.08 g/l, and inhibition degree of 0.323, respectively. The C(I,50) values (the butyrate concentration at which bioactivity is reduced by 50%) for hydrogen production rate and yield were estimated as 19.39 and 20.78 g/l of added butyrate, respectively.

  3. Biological hydrogen production from sucrose and sugar beet by Caldicellulosiruptor saccharolyticus

    Energy Technology Data Exchange (ETDEWEB)

    Panagiotopoulos, John [National Technical Univ. of Athens (Greece); Wageningen UR Food and Biobased Research (Netherlands); Bakker, Robert; Vrieje, Truus de; Claassen, Pieternel [Wageningen UR Food and Biobased Research (Netherlands); Koukios, Emmanuel [National Technical Univ. of Athens (Greece)

    2010-07-01

    Hydrogen production needs to be based on renewable resources in order to be sustainable. Sugar beet is an ideal raw material for fermentative production of hydrogen in the EU and possibly in the USA due to its environmental profile and its potential availability in these areas. In this work, the fermentative production of hydrogen from sucrose of analytical grade and sugar beet extract by pure cultures of Caldicellulosiruptor saccharolyticus was investigated, under uncontrolled and controlled conditions. In the first case, growth of pure cultures of C. saccharolyticus on sucrose derived from sugar beet was compared to growth of the microorganism on sucrose of analytical grade. The production of hydrogen and organic acids (acetate and lactate) from sugar beet was largely equal to or slightly higher than the production of the control. In the second case, fermentation of sugar beet extract at sucrose concentration 10 g/l was comparable to the fermentation on pure sucrose except that the hydrogen yield was slightly higher on sugar beet extract. In particular, hydrogen yields of 2.9 and 3.0 mol/mol hexose were determined in fermentations of sucrose and sugar beet extract, respectively, corresponding to 73% and 75% of the theoretical value of 4 mol hydrogen/mol hexose. Acetic acid was the main product and very low production of lactic acid was observed. (orig.)

  4. Study on efficiency of DCP for nuclear hydrogen production

    Institute of Scientific and Technical Information of China (English)

    LIN Qian; CAO Xue-Wu; JIANG Rui-Peng; ZHANG Xu

    2005-01-01

    With many advantages, hydrogen is considered as the fuel of the future. But there is no natural resource of hydrogen and it must be produced by other kinds of energy. As for the primary energy, nuclear energy is a promising alternative. Using heat from nuclear reactor to produce hydrogen is receiving more and more concerns in recent years. This paper mainly emphasizes the study of the direct contact pyrolysis (DCP) of methane using heat from nuclear reactor. A facility was designed to investigate the efficiency of DCP process in certain conditions. The experimental results show that this process produces only hydrogen and carbon. The conversion efficiency increases with temperature and residence time, but decreases as flow rate increases. The highest efficiency of DCP obtained in this experiment is about 22%.

  5. Economics of hydrogen production and liquefaction updated to 1980

    Science.gov (United States)

    Baker, C. R.

    1979-01-01

    Revised costs for generating and liquefying hydrogen in mid-1980 are presented. Plant investments were treated as straight-forward escalations resulting from inflation. Operating costs, however, were derived in terms of the unit cost of coal, fuel gas and electrical energy to permit the determination of the influence of these parameters on the cost of liquid hydrogen. Inflationary influence was recognized by requiring a 15% discounted rate of return on investment for Discounted Cash Flow financing analysis, up from 12% previously. Utility financing was revised to require an 11% interest rate on debt. The scope of operation of the hydrogen plant was revised from previous studies to include only the hydrogen generation and liquefaction facilities. On-site fuel gas and power generation, originally a part of the plant complex, was eliminated. Fuel gas and power are now treated as purchased utilities. Costs for on-site generation of fuel gas however, are included.

  6. Method and apparatus for hydrogen production from water

    Science.gov (United States)

    Muradov, Nazim Z. (Inventor)

    2012-01-01

    A method, apparatuses and chemical compositions are provided for producing high purity hydrogen from water. Metals or alloys capable of reacting with water and producing hydrogen in aqueous solutions at ambient conditions are reacted with one or more inorganic hydrides capable of releasing hydrogen in aqueous solutions at ambient conditions, one or more transition metal compounds are used to catalyze the reaction and, optionally, one or more alkali metal-based compounds. The metal or alloy is preferably aluminum. The inorganic hydride is from a family of complex inorganic hydrides; most preferably, NaBH.sub.4. The transition metal catalyst is from the groups VIII and IB; preferably, Cu and Fe. The alkali metal-based compounds are preferably NaOH, KOH, and the like. Hydrogen generated has a purity of at least 99.99 vol. % (dry basis), and is used without further purification in all types of fuel cells, including the polymer electrolyte membrane (PEM) fuel cell.

  7. Effect of growth conditions on the hydrogen production with cyanobacterium Anabaena sp. strain CH3

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Pei-Chung [Institute of Clinical Nutrition, Hungkuang University, 34, Chung-Chie Road, Sha Lu, Taichung 433 (China); Fan, Shin-Huei; Chiang, Char-Lin; Lee, Chi-Mei [Department of Environmental Engineering, National Chung Hsing University, 250, Kuo-Kuang Road, Taichung 402 (China)

    2008-03-15

    Cyanobacteria could use sugars as carbon source and reductant to produce hydrogen by nitrogenase. However, oxygen is also produced during photosynthesis and it is an inhibitor of the enzyme nitrogenase. Filamentous cyanobacterium Anabaena sp. CH{sub 3} could use sugars as substrate to produce molecular hydrogen anaerobically. The production activity was dependent on growth phases. It was found that the cells at sub-stage of late-log phase had better ability to produce hydrogen than at log phase. In such case, oxygen content was too low to be detected to inhibit hydrogen production. Among different kinds of sugar, fructose and glucose had the best performance for producing hydrogen. Hydrogen could be accumulated to 0.6 mmol (in 40 ml head space) in 100 h from 1000 ppm fructose. Increasing light intensities from 65 to 130{mu}molm{sup -2}s{sup -1} would enhance hydrogen production to 0.8 mmol. Under illumination of 130{mu}molm{sup -2}s{sup -1} and 2000 ppm fructose, 1.7 mmol of hydrogen could be accumulated. When fructose content was higher than 2000 ppm, cells could not produce more hydrogen at all. (author)

  8. Modelling of hydrogen production in batch cultures of the photosynthetic bacterium Rhodobacter capsulatus

    Energy Technology Data Exchange (ETDEWEB)

    Obeid, Jamila; Magnin, Jean-Pierre [Grenoble Institute of Technology, LEPMI, UMR 5631 (CNRS-INPG-UJF), BP 75, 38402 St Martin d' Heres (France); Flaus, Jean-Marie; Adrot, Olivier [Grenoble Institute of Technology, Laboratoire des sciences pour la conception, l' optimisation et la production, 46, avenue Felix Viallet, 38031 Grenoble (France); Willison, John C. [Laboratoire de Chimie et Biologie des Metaux (UMR 5249 CEA-CNRS-UJF), iRTSV/LCBM, CEA-Grenoble, 38054 Grenoble (France); Zlatev, Roumen [Autonomous University of Baja California, Institute of Engineering, Mexicali, Baja California (Mexico)

    2009-01-15

    The photosynthetic bacterium, Rhodobacter capsulatus, produces hydrogen under nitrogen-limited, anaerobic, photosynthetic culture conditions, using various carbon substrates. In the present study, the relationship between light intensity and hydrogen production has been modelled in order to predict both the rate of hydrogen production and the amount of hydrogen produced at a given time during batch cultures of R. capsulatus. The experimental data were obtained by investigating the effect of different light intensities (6000-50,000 lux) on hydrogen-producing cultures of R. capsulatus grown in a batch photobioreactor, using lactate as carbon and hydrogen source. The rate of hydrogen production increased with increasing light intensity in a manner that was described by a static Baly model, modified to include the square of the light intensity. In agreement with previous studies, the kinetics of substrate utilization and growth of R. capsulatus was represented by the classical Monod or Michaelis-Menten model. When combined with a dynamic Leudekong-Piret model, the amount of hydrogen produced as a function of time was effectively predicted. These results will be useful for the automatization and control of bioprocesses for the photoproduction of hydrogen. (author)

  9. Hydrogen and methane production from swine wastewater using microbial electrolysis cells.

    Science.gov (United States)

    Wagner, Rachel C; Regan, John M; Oh, Sang-Eun; Zuo, Yi; Logan, Bruce E

    2009-03-01

    The production of a useful and valuable product during swine wastewater treatment, such as hydrogen gas, could help to lower treatment costs. Hydrogen can theoretically be produced from wastewater by electrohydrogenesis in a microbial electrolysis cell (MEC) or by fermentation. Using a single-chamber MEC with a graphite-fiber brush anode, hydrogen gas was generated at 0.9-1.0 m(3) m(-3) day(-1) H2 using a full-strength or diluted swine wastewater. COD removals ranged from 8 to 29% in 20-h tests, and from 69 to 75% in longer tests (184 h) using full-strength wastewater. The gas produced was up to 77+/-11% hydrogen, with overall recoveries of up to 28+/-6% of the COD in the wastewater as hydrogen gas. Methane was also produced at a maximum of 13+/-4% of total gas volume. The efficiency of hydrogen production, based on the electrical energy needed (but excluding the energy in the wastewater) compared to the energy of the hydrogen gas produced, was as high as 190+/-39% in 42-h batch tests with undiluted wastewater, but was lower in longer batch tests of 184 h (91+/-6%). Hydrogen gas could not be recovered in fermentation tests using wastewater with a heat-treated inoculum. Hydrogen production was shown to be possible by fermentation when the wastewater was sterilized, but this process would not be practical or energy efficient. We therefore conclude from these tests that MECs are an effective method for hydrogen recovery from swine wastewater treatment, although the process needs to be further evaluated for reducing methane production, increasing the efficiency of converting the organic matter into current, and increasing recovery of hydrogen gas produced at the cathode.

  10. Kinetics of biological hydrogen production by the photosynthetic bacterium Rhodobacter sphaeroides O.U. 001

    Energy Technology Data Exchange (ETDEWEB)

    Koku, Harun; Eroglu, I. [Middle East Technical Univ., Ankara (Turkey). Dept. of Chemical Engineering; Gunduz, U.; Yucel, M. [Middle East Technical Univ., Ankara (Turkey). Dept. of Biology; Turker, L. [Middle East Technical Univ., Ankara (Turkey). Dept. of Chemistry

    2003-04-01

    The kinetics and the effects of various parameters on hydrogen production by Rhodobacter sphaeroides O.U. 001 were investigated in a batch column photobioreactor. In particular, the effect of the inoculum age and the implementation of a light-dark cycle illumination scheme for emulating natural sunlight have been investigated in detail. The possibility of using yeast extract to replace the rather expensive vitamin mixture in the medium was also studied. The results show that hydrogen production is decreased when the initially inoculated bacteria have a high culture age. Exposure of the bacterial culture to light-dark cycles increased the amount of hydrogen compared to continuous illumination, all other parameters remaining the same. Similarly, the use of yeast extract to replace the vitamins increased the growth and hydrogen production rates, however, with a slight reduction in the total amount of gas produced and the hydrogen fraction in the evolved gas. (Author)

  11. Bio-hydrogen Production Using the Visible Light-harvesting Function of Chlorophyll-a

    Energy Technology Data Exchange (ETDEWEB)

    Yutaka Amao; Noriko Himeshima [Department of Applied Chemistry, Oita University, Dannoharu 700, Oita 870-1192, (Japan)

    2006-07-01

    A Bio-hydrogen production system, coupling D-maltose hydrolysis by gluco-amylase and glucose dehydrogenase (GDH) and hydrogen production with platinum nano-particle colloid catalyst using the photo-sensitization based on the visible light harvesting of Mg chlorophyll-a (Mg Chl-a), was developed. Hydrogen gas was continuously produced when the reaction mixture containing D-maltose, gluco-amylase, GDH, nicotinamide adenine dinucleotide (NAD+), Mg Chl-a, methyl-viologen (MV2+) and platinum nano-particle colloid was irradiated by visible light. The amount of hydrogen production was estimated to be 5.0 {mu}mol after 4 h irradiation and the yield of conversion of D-maltose to hydrogen gas was about 1.8%. The quantum yield was 3.1%. (authors)

  12. Hydrogen production by anaerobic microbial communities exposed to repeated heat treatments.

    Science.gov (United States)

    Duangmanee, T; Padmasiri, S I; Simmons, J J; Raskin, L; Sung, S

    2007-09-01

    Biological hydrogen production by anaerobic mixed communities was studied in laboratory-scale bioreactors using sucrose as the substrate. A bioreactor in which a fraction of the return sludge was exposed to repeated heat treatments performed better than a control bioreactor without repeated heat treatment of return sludge and produced a yield of 2.15 moles of hydrogen per mole of sucrose, with 50% hydrogen in the biogas. Terminal restriction fragment length polymorphism analysis showed that two different Clostridium groups (comprised of one or more species) were dominant during hydrogen production. The relative abundance of two other non-Clostridium groups increased during periods of decreased hydrogen production. The first group consisted of Bifidobacterium thermophilum, and the second group included one or more of Bacillus, Melissococcus, Spirochaeta, and Spiroplasma spp.

  13. Hydrogen production from formic acid in pH-stat fed-batch operation for direct supply to fuel cell.

    Science.gov (United States)

    Shin, Jong-Hwan; Yoon, Jong Hyun; Lee, Seung Hoon; Park, Tai Hyun

    2010-01-01

    Enterobacter asburiae SNU-1 harvested after cultivation was used as a whole cell biocatalyst, for the production of hydrogen. Formic acid was efficiently converted to hydrogen using the harvested cells with an initial hydrogen production rate and total hydrogen production of 491 ml/l/h and 6668 ml/l, respectively, when 1 g/l of whole cell enzyme was used. Moreover, new pH-stat fed-batch operation was conducted, and total hydrogen production was 1.4 times higher than that of batch operation. For practical application, bio-hydrogen produced from formic acid using harvested cells was directly applied to PEMFC for power generation.

  14. Multi-criteria analysis on how to select solar radiation hydrogen production system

    Energy Technology Data Exchange (ETDEWEB)

    Badea, G.; Naghiu, G. S., E-mail: naghiu.george@gmail.com; Felseghi, R.-A.; Giurca, I., E-mail: giurca-ioan@yahoo.com [Technical University of Cluj-Napoca, Faculty of Building Services Engineering, Boulevard December 21, no. 128-130, Cluj-Napoca, 400604 (Romania); Răboacă, S. [National R& D Institute for Cryogenic and Isotopic Technologies, str. Uzinei, no. 4, Rm. Vălcea, 240050 (Romania); Aşchilean, I. [SC ACI Cluj SA, Avenue Dorobanţilor, no. 70, Cluj-Napoca, 400609 (Romania)

    2015-12-23

    The purpose of this article is to present a method of selecting hydrogen-production systems using the electric power obtained in photovoltaic systems, and as a selecting method, we suggest the use of the Advanced Multi-Criteria Analysis based on the FRISCO formula. According to the case study on how to select the solar radiation hydrogen production system, the most convenient alternative is the alternative A4, namely the technical solution involving a hydrogen production system based on the electrolysis of water vapor obtained with concentrated solar thermal systems and electrical power obtained using concentrating photovoltaic systems.

  15. Multi-criteria analysis on how to select solar radiation hydrogen production system

    Science.gov (United States)

    Badea, G.; Naghiu, G. S.; Felseghi, R.-A.; Rǎboacǎ, S.; Aşchilean, I.; Giurca, I.

    2015-12-01

    The purpose of this article is to present a method of selecting hydrogen-production systems using the electric power obtained in photovoltaic systems, and as a selecting method, we suggest the use of the Advanced Multi-Criteria Analysis based on the FRISCO formula. According to the case study on how to select the solar radiation hydrogen production system, the most convenient alternative is the alternative A4, namely the technical solution involving a hydrogen production system based on the electrolysis of water vapor obtained with concentrated solar thermal systems and electrical power obtained using concentrating photovoltaic systems.

  16. Application of Bio -hydrogen Production Technology%生物制氢技术的研究进展

    Institute of Scientific and Technical Information of China (English)

    金明兰

    2012-01-01

    氢气具有清洁、可更新的优点,是最具发展潜力、最理想的新能源之一.由于生物制氢技术具有无污染、可再生、成本低等优点,受到国内外广泛的关注,在新能源的研究利用中占有越来越重要的位置.本文较系统地综述了国内外各种生物制氢技术的产生背景、基本原理和应用现状,总结了该技术的优点和面临的问题,探讨其在环境科学中的应用前景.%The hydrogen is a kind of most development potential and best energy source for clean and renewable. Compared with other hydrogen production methods, the technology of bio - hydrogen production was hold more im- portant situation in new energy research for the advantages of being free of pollution, being renewable and with low costs. This presentation comprises a review of the technology of bio - hydrogen production development background, basic technical mechanism and current applications was presented. Its merits and locals were summarized, as well as potential and future perspectives of its applications in environmental science were also approached.

  17. Hydrogen production from rice winery wastewater in an upflow anaerobic reactor by using mixed anaerobic cultures

    Energy Technology Data Exchange (ETDEWEB)

    Hanqing Yu; Zhenhu Zhu [University of Science and Technology, Hefei, Anhui (China). School of Chemistry and Materials; Wenrong Hu [Shandong Univ., Jinan (China). School of Resources and Environmental Engineering; Haisheng Zhang [Jingzi Wine Distillery Company, Shandong (China)

    2002-12-01

    Continuous production of hydrogen from the anaerobic acidogenesis of a high-strength rice winery wastewater by a mixed bacterial flora was demonstrated. The experiment was conducted in a 3.0-l upflow reactor to investigate individual effects of hydraulic retention time (HRT) (2-24 h), chemical oxygen demand (COD) concentration in wastewater (14-36 g COD/l), pH (4.5-6.0) and temperature (20-55{sup o}C) on bio-hydrogen production from the wastewater. The biogas produced under all test conditions was composed of mostly hydrogen (53-61%) and carbon dioxide (37-45%), but contained no detectable methane. Specific hydrogen production rate increased with wastewater concentration and temperature, but with a decrease in HRT. An optimum hydrogen production rate of 9.33 lH{sub 2}/gVSSd was achieved at an HRT of 2 h, COD of 34 g/l, pH 5.5 and 55{sup o}C. The hydrogen yield was in the range of 1.37-2.14 mol/mol-hexose. In addition to acetate, propionate and butyrate, ethanol was also present in the effluent as an aqueous product. The distribution of these compounds in the effluent was more sensitive to wastewater concentration, pH and temperature, but was less sensitive to HRT. This upflow reactor was shown to be a promising biosystem for hydrogen production from high-strength wastewaters by mixed anaerobic cultures. (Author)

  18. Effects of solution volume on hydrogen production by pulsed spark discharge in ethanol solution

    Science.gov (United States)

    Xin, Y. B.; Sun, B.; Zhu, X. M.; Yan, Z. Y.; Liu, H.; Liu, Y. J.

    2016-07-01

    Hydrogen production from ethanol solution (ethanol/water) by pulsed spark discharge was optimized by varying the volume of ethanol solution (liquid volume). Hydrogen yield was initially increased and then decreased with the increase in solution volume, which achieved 1.5 l/min with a solution volume of 500 ml. The characteristics of pulsed spark discharge were studied in this work; the results showed that the intensity of peak current, the rate of current rise, and energy efficiency of hydrogen production can be changed by varying the volume of ethanol solution. Meanwhile, the mechanism analysis of hydrogen production was accomplished by monitoring the process of hydrogen production and the state of free radicals. The analysis showed that decreasing the retention time of gas production and properly increasing the volume of ethanol solution can enhance the hydrogen yield. Through this research, a high-yield and large-scale method of hydrogen production can be achieved, which is more suitable for industrial application.

  19. Estimation of hydrogen production in genetically modified E. coli fermentations using an artificial neural network

    Energy Technology Data Exchange (ETDEWEB)

    Rosales-Colunga, Luis Manuel; De Leon Rodriguez, Antonio [Division de Biologia Molecular, Instituto Potosino de Investigacion Cientifica y Tecnologica, Camino a la Presa San Jose 2055, Col. Lomas 4a secc, San Luis Potosi, SLP 78216 (Mexico); Garcia, Raul Gonzalez [Centro de Investigacion y Estudios de Posgrado, Facultad de Ciencias Quimicas, Universidad Autonoma de San Luis Potosi, Av. Dr. Manuel Nava 6, San Luis Potosi, SLP 78210 (Mexico)

    2010-12-15

    Biological hydrogen production is an active research area due to the importance of this gas as an energy carrier and the advantages of using biological systems to produce it. A cheap and practical on-line hydrogen determination is desired in those processes. In this study, an artificial neural network (ANN) was developed to estimate the hydrogen production in fermentative processes. A back propagation neural network (BPNN) of one hidden layer with 12 nodes was selected. The BPNN training was done using the conjugated gradient algorithm and on-line measurements of dissolved CO{sub 2}, pH and oxidation-reduction potential during the fermentations of cheese whey by Escherichia coli {delta}hycA {delta}lacI (WDHL) strain with or without pH control. The correlation coefficient between the hydrogen production determined by gas chromatography and the hydrogen production estimated by the BPNN was 0.955. Results showed that the BPNN successfully estimated the hydrogen production using only on-line parameters in genetically modified E. coli fermentations either with or without pH control. This approach could be used for other hydrogen production systems. (author)

  20. Hydrogen production using single-chamber membrane-free microbial electrolysis cells.

    Science.gov (United States)

    Hu, Hongqiang; Fan, Yanzhen; Liu, Hong

    2008-09-01

    Microbial electrohydrogenesis provides a new approach for hydrogen generation from renewable biomass. Membranes were used in all the reported microbial electrolysis cells (MECs) to separate the anode and cathode chambers. To reduce the potential losses associated with membrane and increase the energy recovery of this process, single-chamber membrane-free MECs were designed and used to investigate hydrogen production by one mixed culture and one pure culture: Shewanella oneidensis MR-1. At an applied voltage of 0.6 V, this system with a mixed culture achieved a hydrogen production rate of 0.53 m(3)/day/m(3) (0.11 m(3)/day/m(2)) with a current density of 9.3A/m(2) at pH 7 and 0.69 m(3)/day/m(3) (0.15m(3)/day/m(2)) with a current density of 14 A/m(2) at pH 5.8. Stable hydrogen production from lactic acid by S. oneidensis was also observed. Methane was detected during the hydrogen production process with the mixed culture and negatively affected hydrogen production rate. However, by employing suitable approaches, such as exposure of cathodes to air, the hydrogenotrophic methanogens can be suppressed. The current density and volumetric hydrogen production rate of this system have potential to increase significantly by further reducing the electrode spacing and increasing the ratio of electrode surface area/cell volume.

  1. Effects of solution volume on hydrogen production by pulsed spark discharge in ethanol solution

    Energy Technology Data Exchange (ETDEWEB)

    Xin, Y. B.; Sun, B., E-mail: sunb88@dlmu.edu.cn; Zhu, X. M.; Yan, Z. Y.; Liu, H.; Liu, Y. J. [College of Environmental Science and Engineering, Dalian Maritime University, Dalian 116026 (China)

    2016-07-15

    Hydrogen production from ethanol solution (ethanol/water) by pulsed spark discharge was optimized by varying the volume of ethanol solution (liquid volume). Hydrogen yield was initially increased and then decreased with the increase in solution volume, which achieved 1.5 l/min with a solution volume of 500 ml. The characteristics of pulsed spark discharge were studied in this work; the results showed that the intensity of peak current, the rate of current rise, and energy efficiency of hydrogen production can be changed by varying the volume of ethanol solution. Meanwhile, the mechanism analysis of hydrogen production was accomplished by monitoring the process of hydrogen production and the state of free radicals. The analysis showed that decreasing the retention time of gas production and properly increasing the volume of ethanol solution can enhance the hydrogen yield. Through this research, a high-yield and large-scale method of hydrogen production can be achieved, which is more suitable for industrial application.

  2. Bio-hydrogen production from molasses by anaerobic fermentation in continuous stirred tank reactor

    Science.gov (United States)

    Han, Wei; Li, Yong-feng; Chen, Hong; Deng, Jie-xuan; Yang, Chuan-ping

    2010-11-01

    A study of bio-hydrogen production was performed in a continuous flow anaerobic fermentation reactor (with an available volume of 5.4 L). The continuous stirred tank reactor (CSTR) for bio-hydrogen production was operated under the organic loading rates (OLR) of 8-32 kg COD/m3 reactor/d (COD: chemical oxygen demand) with molasses as the substrate. The maximum hydrogen production yield of 8.19 L/d was obtained in the reactor with the OLR increased from 8 kg COD/m3 reactor/d to 24 kg COD/m3 d. However, the hydrogen production and volatile fatty acids (VFAs) drastically decreased at an OLR of 32 kg COD/m3 reactor/d. Ethanoi, acetic, butyric and propionic were the main liquid fermentation products with the percentages of 31%, 24%, 20% and 18%, which formed the mixed-type fermentation.

  3. Achieving ethanol-type fermentation for hydrogen production in a granular sludge system by aeration.

    Science.gov (United States)

    Zhang, Song; Liu, Min; Chen, Ying; Pan, Yu-Ting

    2017-01-01

    To investigate the effects of aeration on hydrogen-producing granular system, experiments were performed in two laboratory-scale anaerobic internal circulation hydrogen production (AICHP) reactors. The preliminary experiment of Reactor 1 showed that direct aeration was beneficial to enhancing hydrogen production. After the direct aeration was implied in Reactor 2, hydrogen production rate (HPR) and hydrogen content were increased by 100% and 60%, respectively. In addition, mixed-acid fermentation was transformed into typical ethanol-type fermentation (ETF). Illumina MiSeq sequencing shows that the direct aeration did not change the species of hydrogen-producing bacteria but altered their abundance. Hydrogen-producing bacteria and ethanol-type fermentative bacteria were increased by 24.5% and 146.3%, respectively. Ethanoligenens sp. sharply increased by 162.2% and turned into predominant bacteria in the system. These findings indicated that appropriate direct aeration might be a novel and promising way to obtain ETF and enhance hydrogen production in practical use. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Long term hydrogen production potential of concentrated photovoltaic (CPV) system in tropical weather of Singapore

    KAUST Repository

    Burhan, Muhammad

    2016-08-23

    Concentrated photovoltaic (CPV) system provides highest solar energy conversion efficiency among all the photovoltaic technologies and provides the most suitable option to convert solar energy into hydrogen, as future sustainable energy carrier. So far, only conventional flat plate PV systems are being used for almost all of the commercial applications. However, most of the studies have only shown the maximum efficiency of hydrogen production using CPV. In actual field conditions, the performance of CPV-Hydrogen system is affected by many parameter and it changes continuously during whole day operation. In this paper, the daily average and long term performances are proposed to analyze the real field potential of the CPV-Hydrogen system, which is of main interest for designers and consumers. An experimental setup is developed and a performance model is proposed to investigate the average and long term production potential of CPV-Hydrogen system. The study is carried out in tropical weather of Singapore. The maximum CPV efficiency of 27-28% and solar to hydrogen (STH) efficiency of 18%, were recorded. In addition, the CPV-Hydrogen system showed the long term average efficiency of 15.5%, for period of one year (12-months), with electrolyser rating of 47 kWh/kg and STH production potential of 218 kWh/kg. Based upon the DNI availability, the system showed hydrogen production potential of 0.153-0.553 kg/m/month, with average production of 0.43 kg/m/month. However, CPV-Hydrogen system has shown annual hydrogen production potential of 5.162 kg/m/year in tropical weather of Singapore.

  5. The Local Product Theorem for bihamiltonian structures

    CERN Document Server

    Turiel, Francisco-Javier

    2011-01-01

    In this work one proves that, around each point of a dense open set (regular points), a real analytic or holomorphic bihamiltonian structure decomposes into a product of a Kronecker bihamiltonian structure and a symplectic one if a necessary condition on the characteristic polynomial of the symplectic factor holds. Moreover we give an example of bihamiltonian structure for showing that this result does not extend to the $C^\\infty$-category. Thus a classical problem on the geometric theory of bihamiltonian structures is solved at almost every point.

  6. Technoeconomic analysis of different options for the production of hydrogen from sunlight, wind, and biomass

    Energy Technology Data Exchange (ETDEWEB)

    Mann, M.K.; Spath, P.L.; Amos, W.A. [National Renewable Energy Lab., Golden, CO (United States)

    1998-08-01

    To determine their technical and economic viability and to provide insight into where each technology is in its development cycle, different options to produce hydrogen from sunlight, wind, and biomass were studied. Additionally, costs for storing and transporting hydrogen were determined for different hydrogen quantities and storage times. The analysis of hydrogen from sunlight examined the selling price of hydrogen from two technologies: direct photoelectrochemical (PEC) conversion of sunlight and photovoltaic (PV)-generated electricity production followed by electrolysis. The wind analysis was based on wind-generated electricity production followed by electrolysis. In addition to the base case analyses, which assume that hydrogen is the sole product, three alternative scenarios explore the economic impact of integrating the PV- and wind-based systems with the electric utility grid. Results show that PEC hydrogen production has the potential to be economically feasible. Additionally, the economics of the PV and wind electrolysis systems are improved by interaction with the grid. The analysis of hydrogen from biomass focused on three gasification technologies. The systems are: low pressure, indirectly-heated gasification followed by steam reforming; high pressure, oxygen-blown gasification followed by steam reforming; and pyrolysis followed by partial oxidation. For each of the systems studied, the downstream process steps include shift conversion followed by hydrogen purification. Only the low pressure system produces hydrogen within the range of the current industry selling prices (typically $0.7--$2/kg, or $5--14/GJ on a HHV basis). A sensitivity analysis showed that, for the other two systems, in order to bring the hydrogen selling price down to $2/kg, negative-priced feedstocks would be required.

  7. Consumer Protection Towards Local Food Production In Southeast Sulawesi Indonesia

    Directory of Open Access Journals (Sweden)

    Suriani BT. Tolo

    2015-08-01

    Full Text Available Abstract Consumers have rights which should not just be ignored by businesses such as the right to be a safety the right be informed the right to be heard as well as the right to a good environment and healthy. Kendari Regency as a local government has been manifested by issuing regulations and policies that support the development of local food production such as the Mayor of Kendari regulation No. 15 of 2010 and Mayor Kendari Decree No. 427 of 2012 regarding the Establishment of Community Care Local Food. It appears that the local government is trying to make this local food as an alternative food. The type of research used in this paper is a socio-legal research reviewing the local food production from the perspective of consumer protection. The outcomes of the research indicate that responsibility of food business operators in the implementation of local production is essentially an effort to assist the government in ensuring the realization of food safety system. Therefore there is a need for awareness of the laws and regulations for all parties involved towards local food production especially in Kendari Regency Southeast Sulawesi on the food production process.

  8. The local physical structure of amorphous hydrogenated boron carbide: insights from magic angle spinning solid-state NMR spectroscopy.

    Science.gov (United States)

    Paquette, Michelle M; Li, Wenjing; Sky Driver, M; Karki, Sudarshan; Caruso, A N; Oyler, Nathan A

    2011-11-01

    Magic angle spinning solid-state nuclear magnetic resonance spectroscopy techniques are applied to the elucidation of the local physical structure of an intermediate product in the plasma-enhanced chemical vapour deposition of thin-film amorphous hydrogenated boron carbide (B(x)C:H(y)) from an orthocarborane precursor. Experimental chemical shifts are compared with theoretical shift predictions from ab initio calculations of model molecular compounds to assign atomic chemical environments, while Lee-Goldburg cross-polarization and heteronuclear recoupling experiments are used to confirm atomic connectivities. A model for the B(x)C:H(y) intermediate is proposed wherein the solid is dominated by predominantly hydrogenated carborane icosahedra that are lightly cross-linked via nonhydrogenated intraicosahedral B atoms, either directly through B-B bonds or through extraicosahedral hydrocarbon chains. While there is no clear evidence for extraicosahedral B aside from boron oxides, ∼40% of the C is found to exist as extraicosahedral hydrocarbon species that are intimately bound within the icosahedral network rather than in segregated phases.

  9. Hydrogen Embrittlement

    Science.gov (United States)

    Woods, Stephen; Lee, Jonathan A.

    2016-01-01

    Hydrogen embrittlement (HE) is a process resulting in a decrease in the fracture toughness or ductility of a metal due to the presence of atomic hydrogen. In addition to pure hydrogen gas as a direct source for the absorption of atomic hydrogen, the damaging effect can manifest itself from other hydrogen-containing gas species such as hydrogen sulfide (H2S), hydrogen chloride (HCl), and hydrogen bromide (HBr) environments. It has been known that H2S environment may result in a much more severe condition of embrittlement than pure hydrogen gas (H2) for certain types of alloys at similar conditions of stress and gas pressure. The reduction of fracture loads can occur at levels well below the yield strength of the material. Hydrogen embrittlement is usually manifest in terms of singular sharp cracks, in contrast to the extensive branching observed for stress corrosion cracking. The initial crack openings and the local deformation associated with crack propagation may be so small that they are difficult to detect except in special nondestructive examinations. Cracks due to HE can grow rapidly with little macroscopic evidence of mechanical deformation in materials that are normally quite ductile. This Technical Memorandum presents a comprehensive review of experimental data for the effects of gaseous Hydrogen Environment Embrittlement (HEE) for several types of metallic materials. Common material screening methods are used to rate the hydrogen degradation of mechanical properties that occur while the material is under an applied stress and exposed to gaseous hydrogen as compared to air or helium, under slow strain rates (SSR) testing. Due to the simplicity and accelerated nature of these tests, the results expressed in terms of HEE index are not intended to necessarily represent true hydrogen service environment for long-term exposure, but rather to provide a practical approach for material screening, which is a useful concept to qualitatively evaluate the severity of

  10. EXPERIMENTAL STUDY OF THE PRODUCTION OF SOLAR HYDROGEN IN ALGERIA

    Directory of Open Access Journals (Sweden)

    W. Bendaikha

    2015-08-01

    Full Text Available Hydrogen is a sustainable fuel option and one of the potential solutions for the current energy and environmental problems. In this study hydrogen is produced using a hydrogen generator with a Proton Exchange Membrane (PEM electrolyser. An experimental study is done in the Center of Development of the Renewable Energy, Algiers, Algeria.The experimental device contains essentially a photovoltaic module, a PEM electrolyser, a gasometer and the devices of measures of characteristics of the PEM electrolyser as well as two pyranometers for the horizontal and diffuse global radiance registration. This system in pilots scale is permitted on the one hand, to measured and analyzed the characteristics: of the PEM electrolyser for two different pressures of working (Patm and P=3 bar, on the other hand, to study the volume of hydrogen produces in the time with different sources of electrical power (generator, photovoltaic module, fluorescent lamp, the efficiency for every case is calculated and compared. We present in this paper the variation of the solar hydrogen flow rate produced according to the global radiance and according to the time for a typical day’s of August.

  11. Metabolic engineering of Escherichia coli to enhance hydrogen production from glycerol.

    Science.gov (United States)

    Tran, Kien Trung; Maeda, Toshinari; Wood, Thomas K

    2014-05-01

    Glycerol is an attractive carbon source for biofuel production since it is cheap and abundant due to the increasing demand for renewable and clean energy sources, which includes production of biodiesel. This research aims to enhance hydrogen production by Escherichia coli from glycerol by manipulating its metabolic pathways via targeted deletions. Since our past strain, which had been engineered for producing hydrogen from glucose, was not suitable for producing hydrogen from glycerol, we rescreened 14 genes related to hydrogen production and glycerol metabolism. We found that 10 single knockouts are beneficial for enhanced hydrogen production from glycerol, namely, frdC (encoding for furmarate reductase), ldhA (lactate dehydrogenase), fdnG (formate dehydrogenase), ppc (phosphoenolpyruvate carboxylase), narG (nitrate reductase), focA (formate transporter), hyaB (the large subunit of hydrogenase 1), aceE (pyruvate dehydrogenase), mgsA (methylglyoxal synthase), and hycA (a regulator of the transcriptional regulator FhlA). On that basis, we created multiple knockout strains via successive P1 transductions. Simultaneous knockouts of frdC, ldhA, fdnG, ppc, narG, mgsA, and hycA created the best strain that produced 5-fold higher hydrogen and had a 5-fold higher hydrogen yield than the parent strain. The engineered strain also reached the theoretical maximum yield of 1 mol H2/mol glycerol after 48 h. Under low partial pressure fermentation, the strain grew over 2-fold faster, indicating faster utilization of glycerol and production of hydrogen. By combining metabolic engineering and low partial pressure fermentation, hydrogen production from glycerol was enhanced significantly.

  12. Hydrogen production in anaerobic reactors during shock loads--influence of formate production and H2 kinetics.

    Science.gov (United States)

    Voolapalli, R K; Stuckey, D C

    2001-05-01

    In this article the role of hydrogen as a process monitoring tool in methanogenic systems was studied by considering the influence of several key system parameters. Hydrogen production was found to be influenced mainly by the inocula's source pH, and varied only slightly with external pH and HCO3- levels. When an inoculum adapted to above neutral conditions (pH > 7) was shocked, reducing equivalents were selectively channelled through formate, while high hydrogen production was noticed with acidically (pH production of hydrogen or formate during shock loads was not strongly associated with microbial morphology (granules or flocs) as high electron fluxes were possible through either during acidogenesis. Shock load experiments in continuous reactors revealed that neither hydrogen nor formate accumulated to any significant degree, nevertheless digester recovery took a long time due to the slow kinetics of volatile fatty acid degradation. Selective formate production under neutral pH environments, coupled with high hydrogenotrophic activity, was found to be responsible for the dampened hydrogen response during the early phases of gradually shocked systems (step change). Based on these results it appears that the role of hydrogen as a process monitoring tool has been overemphasised in the literature.

  13. Biological hydrogen production of the genus Clostridium: Metabolic study and