WorldWideScience

Sample records for loads remained elevated

  1. Study of elevated temperature design standard against thermal loads

    International Nuclear Information System (INIS)

    Kasahara, Naoto; Asayama, Tai; Morishita, Masaki

    2001-01-01

    Elevated temperature components must be designed against both pressure and thermal loads. In the case of sodium circuits of fast breeder reactors, a restriction from the pressure load becomes small because of the high boiling point of sodium. Design approaches for thermal loads (displacement-controlled) are compared with those against pressure loads (load-controlled). Considering differences between those two approaches, a concept of the elevated temperature design standard that takes the nature of thermal loads fully into account is proposed. This concept is a basis of load evaluation techniques and an inelastic analysis guide, that are being developed. Finally, problems and plans to realize the above concept are discussed. (author)

  2. Reactor pressure elevation preventing device upon interruption of load

    International Nuclear Information System (INIS)

    Ota, Yasuo; Okukawa, Ryutaro.

    1996-01-01

    In a power load imbalance circuit of a steam turbine control device, a power load imbalance occurrence signal is outputted for a predetermined period of time upon occurrence of load interruption. A function for suppressing increase of number of rotation of a turbine due to load interruption is not disturbed, and the power load imbalance circuit is not operated at least after a primary peak where the number of rotation of the turbine is increased. Since a steam control valve flow rate demand signal and a turbine bypass valve flow rate demand signals are corporated subsequently to control the opening degree of the steam control valve and the turbine bypass valve, elevation of reactor pressure is always suppressed and maintained constant, as well as abrupt opening of the steam control valve due to cancel of the power load imbalance circuit when steam control valve opening demand is outputted can be prevented. (N.H.)

  3. Preanalytic process linked to spuriously elevated HIV viral loads: improvement on an FDA-approved process.

    Science.gov (United States)

    Procop, Gary W; Taege, Alan J; Starkey, Colleen; Tungsiripat, Marisa; Warner, Diane; Schold, Jesse D; Yen-Lieberman, Belinda

    2017-09-01

    The processing of specimens often occurs in a central processing area within laboratories. We demonstrated that plasma centrifuged in the central laboratory but allowed to remain within the primary tube following centrifugation was associated with spuriously elevated HIV viral loads compared with recentrifugation of the plasma just prior to testing. Copyright © 2016 Elsevier Inc. All rights reserved.

  4. Cellular cholesterol efflux to plasma from proteinuric patients is elevated and remains unaffected by antiproteinuric treatment

    NARCIS (Netherlands)

    Vogt, L; Laverman, GD; van Tol, A; Groen, AK; Navis, G; Dullaart, RPF

    Background. Lipid derangements are assumed to contribute to the elevated cardiovascular risk in proteinuric patients. The impact of proteinuria on reverse cholesterol transport (RCT) is unknown. The first step in RCT, cellular cholesterol efflux to plasma, may be altered in proteinuria, consequent

  5. Recent Successes and Remaining Challenges in Predicting Phosphorus Loading to Surface Waters at Large Scales

    Science.gov (United States)

    Harrison, J.; Metson, G.; Beusen, A.

    2017-12-01

    Over the past century humans have greatly accelerated phosphorus (P) flows from land to aquatic ecosystems, causing eutrophication and associated effects such as harmful algal blooms and hypoxia. Effectively addressing this challenge requires understanding geographic and temporal distribution of aquatic P loading, knowledge of major controls on P loading, and the relative importance of various potential P sources. The Global (N)utrient (E)xport from (W)ater(S)heds) NEWS model and recent improvements and extensions of this modeling system can be used to generate this understanding. This presentation will focus on insights global NEWS models grant into past, present, and potential future P sources and sinks, with a focus on the world's large rivers. Early results suggest: 1) that while aquatic P loading is globally dominated by particulate forms, dissolved P can be locally dominant; 2) that P loading has increased substantially at the global scale, but unevenly between world regions, with hotspots in South and East Asia; 3) that P loading is likely to continue to increase globally, but decrease in certain regions that are actively pursuing proactive P management; and 4) that point sources, especially in urban centers, play an important (even dominant) role in determining loads of dissolved inorganic P. Despite these insights, substantial unexplained variance remains when model predictions and measurements are compared at global and regional scales, for example within the U.S. Disagreements between model predictions and measurements suggest opportunities for model improvement. In particular, explicit inclusion of soil characteristics and the concept of temporal P legacies in future iterations of NEWS (and other) models may help improve correspondence between models and measurements.

  6. Prediction of pavement remaining service life based on repetition of load and permanent deformation

    Science.gov (United States)

    Usman, R. S.; Setyawan, A.; Suprapto, M.

    2018-03-01

    One of the methods which was applied in the assessment of flexible pavement performance was mechanistic method assuming structures of road pavement to become multi-layer structure for flexible pavement, that the vehicle load working on the pavement layer under repetition with power failure worth 1 (one) unit which was assumed as evenly distributed static load, and therefore the pavement material would provide response in the form of stress, strain, and deflection. This is closely related in order to assess the structure of flexible pavement and to predict the remaining service life on the roads of Pulau Indah sta 0 + 000 to sta. 0 + 845 in Kota Kupang, Nusa Tenggara Timur. The performance appraisal indicator which was used was fatigue cracking happening bottom of the asphalt layer and permanent deformation (rutting) on the surface of subgrade. The strain estimate on the flexible pavement layer structure needs carefulness and high accuracy and therefore a software like KENPAVE which produces horizontal tensile strain of 8,802E-05 and vertical compressive strain of 2,642E-04 was used. By applying equation of The Asphalt Instituteit was obtained repetition of permit load when reaching fatigue cracking (Nf) was 16.071.516 ESAL and permanent deformation (rutting) was 14.703.867 ESAL and also it was predicted the remaining service life of pavement applied the equation of AASTHO 1993 by considering Traffic Multiplier factor (TM 1.8, TM 1.9 and TM 2.0) obtained the remaining life service due to fatigue of 5.51% in the year of 13th (TM 1.8), 7.95% in the year of12th (TM 1.9) and 3.11% (TM 2.0) in the year of 12th, also the remaining service life due to rutting of 4.69% in the year of 12th(TM 1.8), 7.79% in the year of 11th (TM 1.9), and 2.94 in the year of 11th (TM 2.0).

  7. The friction coefficient of shoulder joints remains remarkably low over 24 h of loading.

    Science.gov (United States)

    Jones, Brian K; Durney, Krista M; Hung, Clark T; Ateshian, Gerard A

    2015-11-05

    The frictional response of whole human joints over durations spanning activities of daily living has not been reported previously. This study measured the friction of human glenohumeral joints during 24 h of reciprocal loading in a pendulum testing device, at moderate (0.2 mm/s, 4320 cycles) and low (0.02 mm/s, 432 cycles) sliding speeds, under a 200 N load. The effect of joint congruence was also investigated by testing human humeral heads against significantly larger mature bovine glenoids. Eight human joints and six bovine joints were tested in four combinations: human joints tested at moderate (hHCMS, n=6) and low speed (hHCLS, n=3), human humeral heads tested against bovine glenoids at moderate speed (LCMS, n=3), and bovine joints tested at moderate speed (bHCMS, n=3). In the first half hour the mean±standard deviation of the friction coefficient was hHCMS: 0.0016±0.0011, hHCLS: 0.0012±0.0002, LCMS: 0.0008±0.0002 and bHCMS: 0.0024±0.0008; in the last four hours it was hHCMS: 0.0057±0.0025, hHCLS: 0.0047±0.0017, LCMS: 0.0012±0.0003 and bHCMS: 0.0056±0.0016. The initial value was lower than the final value (pfriction coefficient of natural human shoulders remains remarkably low (averaging as little as 0.0015 and no greater than 0.006) for up to 24 h of continuous loading. The sustained low friction coefficients observed in incongruent joints (~0.001) likely represent rolling rather than sliding friction. Copyright © 2015. Published by Elsevier Ltd.

  8. The Friction Coefficient of Shoulder Joints Remains Remarkably Low Over 24 h of Loading

    Science.gov (United States)

    Jones, Brian K.; Durney, Krista M.; Hung, Clark T.; Ateshian, Gerard A.

    2015-01-01

    The frictional response of whole human joints over durations spanning activities of daily living has not been reported previously. This study measured the friction of human glenohumeral joints during 24 h of reciprocal loading in a pendulum testing device, at moderate (0.2 mm/s, 4320 cycles) and low (0.02 mm/s, 432 cycles) sliding speeds, under a 200 N load. The effect of joint congruence was also investigated by testing human humeral heads against significantly larger mature bovine glenoids. Six human joints and six bovine joints were tested in four combinations: human joints tested at moderate (hHCMS, n=6) and low speed (hHCLS, n=3), human humeral heads tested against bovine glenoids at moderate speed (LCMS, n=3), and bovine joints tested at moderate speed (bHCMS, n=3). In the first half hour the mean ± standard deviation of the friction coefficient was hHCMS: 0.0016±0.0011, hHCLS: 0.0012±0.0002, LCMS: 0.0008±0.0002 and bHCMS: 0.0024±0.0008; in the last four hours it was hHCMS: 0.0057±0.0025, hHCLS: 0.0047±0.0017, LCMS: 0.0012±0.0003 and bHCMS: 0.0056±0.0016. The initial value was lower than the final value (pfriction coefficient of natural human shoulders remains remarkably low (averaging as little as 0.0015 and no greater than 0.006) for up to 24 h of continuous loading. The sustained low friction coefficients observed in incongruent joints (~0.001) likely represent rolling rather than sliding friction. PMID:26472306

  9. Ensemble coding remains accurate under object and spatial visual working memory load.

    Science.gov (United States)

    Epstein, Michael L; Emmanouil, Tatiana A

    2017-10-01

    A number of studies have provided evidence that the visual system statistically summarizes large amounts of information that would exceed the limitations of attention and working memory (ensemble coding). However the necessity of working memory resources for ensemble coding has not yet been tested directly. In the current study, we used a dual task design to test the effect of object and spatial visual working memory load on size averaging accuracy. In Experiment 1, we tested participants' accuracy in comparing the mean size of two sets under various levels of object visual working memory load. Although the accuracy of average size judgments depended on the difference in mean size between the two sets, we found no effect of working memory load. In Experiment 2, we tested the same average size judgment while participants were under spatial visual working memory load, again finding no effect of load on averaging accuracy. Overall our results reveal that ensemble coding can proceed unimpeded and highly accurately under both object and spatial visual working memory load, providing further evidence that ensemble coding reflects a basic perceptual process distinct from that of individual object processing.

  10. Influence of elevator acceleration induced loading on injury levels

    NARCIS (Netherlands)

    Funai, K.; Schijndel-de Nooij, M. van; Nunen, E. van

    2008-01-01

    The influence on human body of the acceleration caused by the elevator emergency stop has been studied. Experiments were performed with an automotive dummy in an elevator. The study is furthermore based on numerical simulations in MADYMO with an active human model. Kinematics and contact forces of

  11. The Effects of Using a Ramp and Elevator to Load and Unload Trailers on the Behavior and Physiology of Piglets

    Directory of Open Access Journals (Sweden)

    John McGlone

    2014-09-01

    Full Text Available Transport is an inevitable process in the modern U.S. swine industry. The loading process is a novel and potentially stressful experience. This study uses behavior, heart rate and leukocyte counts to compare stress one hour before, during and after loading via ramp or elevator. Piglets were held in a home pen (control (CON, walked up and down an aisle (handled (HAN, or walked to a truck and loaded via elevator (ELE or ramp (RAM. Sitting, feeding and blood parameters did not show a significant treatment by time effect (p > 0.05. Standing behavior did not differ between CON and HAN piglets nor between RAM and ELE piglets (p > 0.05; however, CON and HAN piglets stood more than RAM and ELE piglets during treatment (p < 0.05. After treatment, drinking behavior was increased in RAM piglets (p < 0.05. The heart rate of ELE piglets decreased 6.3% after treatment; whereas the heart rate of RAM piglets remained elevated 2.4% (p < 0.05. In terms of heart rate, loading by elevator appears to be less stressful than loading by ramp.

  12. Prolonged elevation of viral loads in HIV-1-infected children

    African Journals Online (AJOL)

    cqq1a

    2010-11-09

    Nov 9, 2010 ... treatment i.e. mean difference (signed-rank test) in viral load “before” and .... We used Abbott Determine and Unigold as the rapid HIV test kits. The ..... N: Number of patients, *: Wilcoxon signed ranks test for Median difference ...

  13. Interleukin-6 and intercellular cell adhesion molecule-1 expression remains elevated in revived live endothelial cells following spaceflight.

    Science.gov (United States)

    Muid, S; Froemming, G R A; Ali, A M; Nawawi, H

    2013-12-01

    The effects of spaceflight on cardiovascular health are not necessarily seen immediately after astronauts have returned but can be delayed. It is important to investigate the long term effects of spaceflight on protein and gene expression of inflammation and endothelial activation as a predictor for the development of atherosclerosis and potential cardiovascular problems. The objectives of this study were to investigate the (a) protein and gene expression of inflammation and endothelial activation, (b) expression of nuclear factor kappa B (NFκB), signal transducer and activator of transcription-3 (STAT-3) and endothelial nitric oxide synthase (eNOS) in human umbilical vein endothelial cells (HUVEC) 3 months post-space flight travel compared to ground controls. HUVEC cultured on microcarriers in fluid processing apparatus were flown to the International Space Station (ISS) by the Soyuz TMA-11 rocket. After landing, the cells were detached from microcarriers and recultured in T-25 cm(2) culture flasks (Revived HUVEC). Soluble protein expression of IL-6, TNF-α, ICAM-1, VCAM-1 and e-selectin were measured by ELISA. Gene expression of these markers and in addition NFκB, STAT-3 and eNOS were measured. Spaceflight induced IL-6 and ICAM-1 remain elevated even after 3 months post spaceflight travel and this is mediated via STAT-3 pathway. The downregulation of eNOS expression in revived HUVEC cells suggests a reduced protection of the cells and the surrounding vessels against future insults that may lead to atherosclerosis. It would be crucial to explore preventive measures, in relation to atherosclerosis and its related complications.

  14. Response of ferritic steels to nonsteady loading at elevated temperatures

    International Nuclear Information System (INIS)

    Swindeman, R.W.

    1984-01-01

    High-temperature operating experience is lacking in pressure vessel materials that have strength levels above 586 MPa. Because of their tendency toward strain softening, we have been concerned about their behavior under nonsteady loading. Testing was undertaken to explore the extent of softening produced by monotonic and cyclic strains. The specific materials included bainitic 2 1/4Cr-1Mo steel, a micro-alloyed version of 2 1/4Cr-1Mo steel, a micro-alloyed version of 2 1/4Cr-1Mo steel containing vanadium, titanium, and boron, and a martensitic 9Cr-1Mo-V-Nb steel. Tests included tensile, creep, variable stress creep, relaxation, strain cycling, stress cycling, and non-isothermal creep ratchetting experiments. We found that these steels had very low uniform elongation and exhibited small strains to the onset of tertiary creep compared to annealed 2 1/4Cr-1Mo steel. Repeated relaxation test data also indicated a limited capacity for strain hardening. Reversal strains produced softening. The degree of softening increased with increased initial strength level. We concluded that the high strength bainitic and martensitic steels should perform well when used under conditions where severe cyclic operation does not occur

  15. Apparatuses and methods of determining if a person operating equipment is experiencing an elevated cognitive load

    Science.gov (United States)

    Watkins, Michael L.; Keller, Paul Edwin; Amaya, Ivan A.

    2015-06-16

    A method of, and apparatus for, determining if a person operating equipment is experiencing an elevated cognitive load, wherein the person's use of a device at a first time is monitored so as to set a baseline signature. Then, at a later time, the person's use of the device is monitored to determine the person's performance at the second time, as represented by a performance signature. This performance signature can then be compared against the baseline signature to predict whether the person is experiencing an elevated cognitive load.

  16. High Altitude Remains Associated with Elevated Suicide Rates after Adjusting for Socioeconomic Status: A Study from South Korea

    OpenAIRE

    Kim, Jaelim; Choi, Nari; Lee, Yu-Jin; An, Hyonggin; Kim, Namkug; Yoon, Ho-Kyoung; Lee, Heon-Jeong

    2014-01-01

    There have been several studies supporting a possible relationship between high suicide rate and high altitude. However socioeconomic status may confound this association because low socioeconomic status, which is known to be related to a high suicide rate, is also associated with living at high altitude. This study aims to explore whether the relationship between high altitude and high suicide rate remains after adjusting for socioeconomic status in South Korea. We collected demographic data...

  17. Concrete for PCRVs: strength of concrete under triaxial loading and creep at elevated temperatures

    International Nuclear Information System (INIS)

    Linse, D.; Aschl, H.; Stoeckl, S.

    1975-01-01

    To provide detailed information for the calculation of prestressed concrete reactor vessels, investigations of the behaviour of concrete under multiaxial loading and on creep at elevated temperatures were made at the Institut fuer Massivbau of the Technical University of Munich. The strength of concrete under triaxial compression is dependent on the stress ratio. The less the stresses differ from hydrostatic compression the more strength increases. Triaxial compression increases very much the deformability of concrete. Plastic deformations of +-10% and more (all stresses compression, but not equal, strains compression or tension) are possible without large cracks. The creep deformations are considerably dependent on the temperature. Creep at 80 0 C is about three to four times higher than at 20 0 C. The Poisson's ratio of creep at elevated temperature seems to be bigger than at normal temperatures at a rate of loading of 35% and 50% of the ultimate strength. (Auth.)

  18. The Effects of Using a Ramp and Elevator to Load and Unload Trailers on the Behavior and Physiology of Piglets.

    Science.gov (United States)

    McGlone, John; Sapkota, Avi

    2014-09-11

    Transport is an inevitable process in the modern U.S. swine industry. The loading process is a novel and potentially stressful experience. This study uses behavior, heart rate and leukocyte counts to compare stress one hour before, during and after loading via ramp or elevator. Piglets were held in a home pen (control (CON)), walked up and down an aisle (handled (HAN)), or walked to a truck and loaded via elevator (ELE) or ramp (RAM). Sitting, feeding and blood parameters did not show a significant treatment by time effect (p > 0.05). Standing behavior did not differ between CON and HAN piglets nor between RAM and ELE piglets (p > 0.05); however, CON and HAN piglets stood more than RAM and ELE piglets during treatment (p elevated 2.4% (p elevator appears to be less stressful than loading by ramp.

  19. Biomechanical evaluation of heel elevation on load transfer — experimental measurement and finite element analysis

    Science.gov (United States)

    Luximon, Yan; Luximon, Ameersing; Yu, Jia; Zhang, Ming

    2012-02-01

    In spite of ill-effects of high heel shoes, they are widely used for women. Hence, it is essential to understand the load transfer biomechanics in order to design better fit and comfortable shoes. In this study, both experimental measurement and finite element analysis were used to evaluate the biomechanical effects of heel height on foot load transfer. A controlled experiment was conducted using custom-designed platforms. Under different weight-bearing conditions, peak plantar pressure, contact area and center of pressure were analyzed. A three-dimensional finite element foot model was used to simulate the high-heel support and to predict the internal stress distributions and deformations for different heel heights. Results from both experiment and model indicated that heel elevations had significant effects on all variables. When heel elevation increased, the center of pressure shifted from the midfoot region to the forefoot region, the contact area was reduced by 26% from 0 to 10.2 cm heel and the internal stress of foot bones increased. Prediction results also showed that the strain and total tension force of plantar fascia was minimum at 5.1 cm heel condition. This study helps to better understand the biomechanical behavior of foot, and to provide better suggestions for design parameters of high heeled shoes.

  20. Dynamics of a Circular Mindlin Plate under Mechanical Loading and Elevated Temperature

    Directory of Open Access Journals (Sweden)

    Warminska Anna

    2016-01-01

    Full Text Available Dynamics of a nonlinear circular Midlin plate is studied in the paper. The mathematical model represented by partial differential equations includes nonlinear geometrical terms resulted from large displacements. The plate is subjected to mechanical and thermal loadings. The dynamics of a coupled thermo-mechanical problem is reduced from partial to ordinary differential equations. Considering the first mode reduction and uniformly distributed temperature just a single nonlinear differential equation is obtained. The bifurcation analysis shows that elevated temperature shifts the rezonanse curve and new solutions arise. Depending on initial conditions this may lead to buckling phenomenon and then relatively small oscillations around this state, symmetric periodic oscillations of large amplitude, or irregular oscillations.

  1. Decreased insulin clearance in individuals with elevated 1-h post-load plasma glucose levels.

    Directory of Open Access Journals (Sweden)

    Maria Adelaide Marini

    Full Text Available Reduced insulin clearance has been shown to predict the development of type 2 diabetes. Recently, it has been suggested that plasma glucose concentrations ≥ 8.6 mmol/l (155 mg/dl at 1 h during an oral glucose tolerance test (OGTT can identify individuals at high risk for type 2 diabetes among those who have normal glucose tolerance (NGT 1 h-high. The aim of this study was to examine whether NGT 1 h-high have a decrease in insulin clearance, as compared with NGT individuals with 1-h post-load glucose <8.6 mmol/l (l (155 mg/dl, NGT 1 h-low. To this end, 438 non-diabetic White individuals were subjected to OGTT and euglycemic-hyperinsulinemic clamp to evaluate insulin clearance and insulin sensitivity. As compared with NGT 1 h-low individuals, NGT 1 h-high had significantly higher 1-h and 2-h post-load plasma glucose and 2-h insulin levels as well as higher fasting glucose and insulin levels. NGT 1 h-high exhibited also a significant decrease in both insulin sensitivity (P<0.0001 and insulin clearance (P = 0.006 after adjusting for age, gender, adiposity measures, and insulin sensitivity. The differences in insulin clearance remained significant after adjustment for fasting glucose (P = 0.02 in addition to gender, age, and BMI. In univariate analyses adjusted for gender and age, insulin clearance was inversely correlated with body weight, body mass index, waist, fat mass, 1-h and 2-h post-load glucose levels, fasting, 1-h and 2-h post-load insulin levels, and insulin-stimulated glucose disposal. In conclusion, our data show that NGT 1 h-high have a reduction in insulin clearance as compared with NGT 1 h-low individuals; this suggests that impaired insulin clearance may contribute to sustained fasting and post-meal hyperinsulinemia.

  2. De novo biofilm community assembly from tap water source communities favors Nitrotoga over Nitrospira under elevated nitrite surface loading

    DEFF Research Database (Denmark)

    Kinnunen, Marta; Dechesne, Arnaud; Albrechtsen, Hans-Jørgen

    -through biofilm system to continuous immigration from a tap water metacommunity while applying different nitrite surface loading rates. After 63 days of operation, we extracted biofilms and analyzed the community composition via Illumina MiSeq targeting the 16S rRNA gene. Previous studies have shown...... that Nitrospira is the dominant nitrite oxidizing genus in low nitrite environments. Hence, we postulated that by elevating the nitrite surface loading we would select for NOB with lower nitrite affinity than Nitrospira. We observed different dominant NOB species under different loading rates. While...... in the metacommunity, Nitrotoga and Nitrospira were found at near equal abundances, in the biofilm community, elevated nitrite loading strongly selected for Nitrotoga over Nitrospira. The biofilms were also significantly different in their alpha-diversity (pdiversity, and the evenness and richness...

  3. Characterizing Axial Stiffness of Individual Batter Piles with Emphasis on Elevated, Laterally Loaded, Clustered Pile Groups

    Science.gov (United States)

    2016-11-01

    using the appropriate stiffness based on the direction of the calculated pile load. 1...load cases. CPGA utilizes the stiffness method (Saul 1968) of three-dimensional pile group analysis for user-specified static loadings. The pile...CPGA analysis and coordinate systems (global and pile) As discussed in Chapter 1, the CPGA software utilizes the stiffness method (Saul 1968) of

  4. D-Dimer Levels before HIV Seroconversion Remain Elevated Even after Viral Suppression and Are Associated with an Increased Risk of Non-AIDS Events.

    Directory of Open Access Journals (Sweden)

    Matthew S Freiberg

    Full Text Available The mechanism underlying the excess risk of non-AIDS diseases among HIV infected people is unclear. HIV associated inflammation/hypercoagulability likely plays a role. While antiretroviral therapy (ART may return this process to pre-HIV levels, this has not been directly demonstrated. We analyzed data/specimens on 249 HIV+ participants from the US Military HIV Natural History Study, a prospective, multicenter observational cohort of >5600 active duty military personnel and beneficiaries living with HIV. We used stored blood specimens to measure D-dimer and Interleukin-6 (IL-6 at three time points: pre-HIV seroconversion, ≥6 months post-HIV seroconversion but prior to ART initiation, and ≥6 months post-ART with documented HIV viral suppression on two successive evaluations. We evaluated the changes in biomarker levels between time points, and the association between these biomarker changes and future non-AIDS events. During a median follow-up of 3.7 years, there were 28 incident non-AIDS diseases. At ART initiation, the median CD4 count was 361cells/mm3; median duration of documented HIV infection 392 days; median time on ART was 354 days. Adjusted mean percent increase in D-dimer levels from pre-seroconversion to post-ART was 75.1% (95% confidence interval 24.6-148.0, p = 0.002. This increase in D-dimer was associated with a significant 22% increase risk of future non-AIDS events (p = 0.03. Changes in IL-6 levels across time points were small and not associated with future non-AIDS events. In conclusion, ART initiation and HIV viral suppression does not eliminate HIV associated elevation in D-dimer levels. This residual pathology is associated with an increased risk of future non-AIDS diseases.

  5. Elevated temperature inelastic analysis of metallic media under time varying loads using state variable theories

    International Nuclear Information System (INIS)

    Kumar, V.; Mukherjee, S.

    1977-01-01

    In the present paper a general time-dependent inelastic analysis procedure for three-dimensional bodies subjected to arbitrary time varying mechanical and thermal loads using these state variable theories is presented. For the purpose of illustrations, the problems of hollow spheres, cylinders and solid circular shafts subjected to various combinations of internal and external pressures, axial force (or constraint) and torque are analyzed using the proposed solution procedure. Various cyclic thermal and mechanical loading histories with rectangular or sawtooth type waves with or without hold-time are considered. Numerical results for these geometrical shapes for various such loading histories are presented using Hart's theory (Journal of Engineering Materials and Technology 1976). The calculations are performed for nickel in the temperature range of 25 0 C to 400 0 C. For integrating forward in time, a method of solving a stiff system of ordinary differential equations is employed which corrects the step size and order of the method automatically. The limit loads for hollow spheres and cylinders are calculated using the proposed method and Hart's theory, and comparisons are made against the known theoretical results. The numerical results for other loading histories are discussed in the context of Hart's state variable type constitutive relations. The significance of phenomena such as strain rate sensitivity, Bauschinger's effect, crep recovery, history dependence and material softening with regard to these multiaxial problems are discussed in the context of Hart's theory

  6. Load-partitioning in an oxide dispersion-strengthened 310 steel at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Miao, Yinbin; Mo, Kun; Zhou, Zhangjian; Liu, Xiang; Lan, Kuan-Che; Zhang, Guangming; Park, Jun-Sang; Almer, Jonathan; Stubbins, James F.

    2016-12-01

    Here the high temperature tensile performance of an oxide dispersion-strengthened (ODS) 310 steel is reported upon. The microstructure of the steel was examined through both transmission electron microscopy (TEM) and synchrotron scattering. In situ synchrotron tensile investigation was performed at a variety of temperatures, from room temperature up to 800°C. Pyrochlore structure yttrium titanate and sodium chloride structure titanium nitride phases were identified in the steel along with an austenite matrix and marginal residual α’-martensite. The inclusion phases strengthen the steel by taking extra load through particle-dislocation interaction during plastic deformation or dislocation creep procedures. As temperature rises, the load partitioning effect of conventional precipitate phases starts to diminish, whereas those ultra-fine oxygen-enriched nanoparticles continue to bear a considerable amount of extra load. Introduction of oxygen-enriched nanoparticles in austenitic steel proves to improve the high temperature performance, making austenitic ODS steels promising for advanced nuclear applications.

  7. Elevated-temperature benchmark tests of simply supported beams and circular plates subjected to time-varying loadings

    International Nuclear Information System (INIS)

    Corum, J.M.; Richardson, M.; Clinard, J.A.

    1977-01-01

    This report presents the measured elastic-plastic-creep responses of eight simply supported type 304 stainless steel beams and circular plates that were subjected to time-varying loadings at elevated temperature. The tests were performed to provide experimental benchmark problem data suitable for assessing inelastic analysis methods and for validating computer programs. Beams and plates exhibit the essential features of inelastic structural behavior; yet they are relatively simple and the experimental results are generally easy to interpret. The stress fields are largely uniaxial in beams, while multiaxial effects are introduced in plates. The specimens tested were laterally loaded at the center and subjected to either a prescribed load or a center deflection history. The specimens were machined from a common well-characterized heat of material, and all the tests were performed at a temperature of 593 0 C (1100 0 F). Test results are presented in terms of the load and center deflection behaviors, which typify the overall structural behavior. Additional deflection data, as well as strain gage results and mechanical properties data for the beam and plate material, are provided in the appendices

  8. Effects of Contact Load on the Fretting Fatigue Behavior of IN-100 at Elevated Temperature

    Science.gov (United States)

    2009-03-01

    Effect of contact pressure on fretting fatigue of austenitic stainless steel ,” Tribology International, vol. 36, pp. 79-85, 2003. 155 [56] N.K. Naidu...austenitic stainless steel was presented. Like the studies in the previous section, this study investigated how a variably increased contact load...that their stainless steel specimens acted much in the same manner as the aluminum specimens presented in the previous section. It was observed

  9. Experimental investigation on the failure of T-joints at elevated temperature under unaxial loading

    Science.gov (United States)

    Bahri, N. F.; Afendi, M.; Razlan, Z. M.; Nor, A.; Baharuddin, S. A.

    2017-09-01

    In this study, the mechanical properties and maximum failure load of a bulk and T-joints subjected to tensile loading were investigated experimentally. A bulk and the T-joint specimens were fabricated and tested in order to investigate the effects of temperature conditions on the failure of the joints. The adherent and adhesive used for T-joint are 304 L stainless steel and Hysol E 214 HP with the adhesive thickness of 1.0 mm. The tensile test of the bulk specimen and adhesively T-joint were conducted by using a universal testing machine (UTM) at room temperature (RT), 55 °C, 75 °C, 100 °C and 120 °C, respectively. It was found that as the temperature increases, the failure force strength decreases for bulk and T-joint specimen. Data obtained from the tests at 120 °C showed the failure force of the bulk adhesive decreased by approximately 44 % compared to the specimen tested at RT. Next, the bulk of Hysol failure force result was compared with Araldite at RT and 100 °C. Araldite data was taken from the previous study [1]. It has also been found that the bulk for Hysol has higher failure force compared to Araldite at RT and 100 °C.

  10. Thermomechanical behavior of different Ni-base superalloys during cyclic loading at elevated temperatures

    Directory of Open Access Journals (Sweden)

    Huber Daniel

    2014-01-01

    Full Text Available The material behavior of three Ni-base superalloys (Inconel® 718, Allvac® 718PlusTM and Haynes® 282® during in-phase cyclic mechanical and thermal loading was investigated. Stress controlled thermo-mechanical tests were carried out at temperatures above 700 ∘C and different levels of maximum compressive stress using a Gleeble® 3800 testing system. Microstructure investigations via light optical microscopy (LOM and field emission gun scanning electron microscopy (FEG-SEM as well as numerical precipitation kinetics simulations were performed to interpret the obtained results. For all alloys, the predominant deformation mechanism during deformation up to low plastic strains was identified as dislocation creep. The main softening mechanism causing progressive increase of plastic strain after preceding linear behavior is suggested to be recrystallization facilitated by coarsening of grain boundary precipitates. Furthermore, coarsening and partial transformation of strengthening phases was observed. At all stress levels, Haynes® 282® showed best performance which is attributable to its stable microstructure containing a high phase fraction of small, intermetallic precipitates inside grains and different carbides evenly distributed along grain boundaries.

  11. Mechanical Behavior of AZ31B Mg Alloy Sheets under Monotonic and Cyclic Loadings at Room and Moderately Elevated Temperatures

    Directory of Open Access Journals (Sweden)

    Ngoc-Trung Nguyen

    2014-02-01

    Full Text Available Large-strain monotonic and cyclic loading tests of AZ31B magnesium alloy sheets were performed with a newly developed testing system, at different temperatures, ranging from room temperature to 250 °C. Behaviors showing significant twinning during initial in-plane compression and untwinning in subsequent tension at and slightly above room temperature were recorded. Strong yielding asymmetry and nonlinear hardening behavior were also revealed. Considerable Bauschinger effects, transient behavior, and variable permanent softening responses were observed near room temperature, but these were reduced and almost disappeared as the temperature increased. Different stress–strain responses were inherent to the activation of twinning at lower temperatures and non-basal slip systems at elevated temperatures. A critical temperature was identified to account for the transition between the twinning-dominant and slip-dominant deformation mechanisms. Accordingly, below the transition point, stress–strain curves of cyclic loading tests exhibited concave-up shapes for compression or compression following tension, and an unusual S-shape for tension following compression. This unusual shape disappeared when the temperature was above the transition point. Shrinkage of the elastic range and variation in Young’s modulus due to plastic strain deformation during stress reversals were also observed. The texture-induced anisotropy of both the elastic and plastic behaviors was characterized experimentally.

  12. Intestinal microbiota shifts towards elevated commensal Escherichia coli loads abrogate colonization resistance against Campylobacter jejuni in mice.

    Directory of Open Access Journals (Sweden)

    Lea-Maxie Haag

    Full Text Available BACKGROUND: The zoonotic pathogen Campylobacter jejuni is a leading cause of bacterial foodborne enterocolitis in humans worldwide. The understanding of immunopathology underlying human campylobacteriosis is hampered by the fact that mice display strong colonization resistance against the pathogen due to their host specific gut microbiota composition. METHODOLOGY/PRINCIPAL FINDINGS: Since the microbiota composition changes significantly during intestinal inflammation we dissected factors contributing to colonization resistance against C. jejuni in murine ileitis, colitis and in infant mice. In contrast to healthy animals C. jejuni could stably colonize mice suffering from intestinal inflammation. Strikingly, in mice with Toxoplasma gondii-induced acute ileitis, C. jejuni disseminated to mesenteric lymphnodes, spleen, liver, kidney, and blood. In infant mice C. jejuni infection induced enterocolitis. Mice suffering from intestinal inflammation and C. jejuni susceptible infant mice displayed characteristical microbiota shifts dominated by increased numbers of commensal Escherichia coli. To further dissect the pivotal role of those distinct microbiota shifts in abrogating colonization resistance, we investigated C. jejuni infection in healthy adult mice in which the microbiota was artificially modified by feeding live commensal E. coli. Strikingly, in animals harboring supra-physiological intestinal E. coli loads, colonization resistance was significantly diminished and C. jejuni infection induced enterocolitis mimicking key features of human campylobacteriosis. CONCLUSION/SIGNIFICANCE: Murine colonization resistance against C. jejuni is abrogated by changes in the microbiota composition towards elevated E. coli loads during intestinal inflammation as well as in infant mice. Intestinal inflammation and microbiota shifts thus represent potential risk factors for C. jejuni infection. Corresponding interplays between C. jejuni and microbiota might

  13. Rice (Oryza sativa japonica) Albumin Suppresses the Elevation of Blood Glucose and Plasma Insulin Levels after Oral Glucose Loading.

    Science.gov (United States)

    Ina, Shigenobu; Ninomiya, Kazumi; Mogi, Takashi; Hase, Ayumu; Ando, Toshiki; Matsukaze, Narumi; Ogihara, Jun; Akao, Makoto; Kumagai, Hitoshi; Kumagai, Hitomi

    2016-06-22

    The suppressive effect of rice albumin (RA) of 16 kDa on elevation of blood glucose level after oral loading of starch or glucose and its possible mechanism were examined. RA suppressed the increase in blood glucose levels in both the oral starch tolerance test and the oral glucose tolerance test. The blood glucose concentrations 15 min after the oral administration of starch were 144 ± 6 mg/dL for control group and 127 ± 4 mg/dL for RA 200 mg/kg BW group, while those after the oral administration of glucose were 157 ± 7 mg/dL for control group and 137 ± 4 mg/dL for RA 200 mg/kg BW group. However, in the intraperitoneal glucose tolerance test, no significant differences in blood glucose level were observed between RA and the control groups, indicating that RA suppresses the glucose absorption from the small intestine. However, RA did not inhibit the activity of mammalian α-amylase. RA was hydrolyzed to an indigestible high-molecular-weight peptide (HMP) of 14 kDa and low-molecular-weight peptides by pepsin and pancreatin. Furthermore, RA suppressed the glucose diffusion rate through a semipermeable membrane like dietary fibers in vitro. Therefore, the indigestible HMP may adsorb glucose and suppress its absorption from the small intestine.

  14. A fast and robust bulk-loading algorithm for indexing very large digital elevation datasets II. Experimental results

    Science.gov (United States)

    Rodríguez, Félix R.; Barrena, Manuel

    2011-07-01

    The spatial indexing of eventually all the available topographic information of Earth is a highly valuable tool for different geoscientific application domains. The Shuttle Radar Topography Mission (SRTM) collected and made available to the public one of the world's largest digital elevation models (DEMs). With the aim of providing on easier and faster access to these data by improving their further analysis and processing, we have indexed the SRTM DEM by means of a spatial index based on the kd-tree data structure, called the Q-tree. This paper is the second in a two-part series that includes a thorough performance analysis to validate the bulk-load algorithm efficiency of the Q-tree. We investigate performance measuring elapsed time in different contexts, analyzing disk space usage, testing response time with typical queries, and validating the final index structure balance. In addition, the paper includes performance comparisons with Oracle 11g that helps to understand the real cost of our proposal. Our tests prove that the proposed algorithm outperforms Oracle 11g using around a 9% of the elapsed time, taking six times less storage with more than 96% of page utilization, and getting faster response times to spatial queries issued on 4.5 million points. In addition to this, the behavior of the spatial index has been successfully tested on both an open GIS (VT Builder) and a visualizer tool derived from the previous one.

  15. Sinus Floor Elevation with Modified Crestal Approach and Single Loaded Short Implants: A Case Report with 4 Years of Follow-Up

    Directory of Open Access Journals (Sweden)

    Michele Perelli

    2017-01-01

    Full Text Available Tooth extraction is usually followed by bone reduction. In the maxillary posterior region, this remodelling combined with sinus pneumatisation and periodontal defects may lead to a reduced basal bone height available for implant placement. Sinus floor elevation can be performed with different surgical techniques. Crestal approach has demonstrated to be effective, less invasive, and associated with a reduced morbidity. This article reports a modified sinus floor elevation by means of rotary, noncutting instruments, addition of xenograft, and 2 short-threaded implant placements. The aim of the study was to evaluate the implant’s success and intrasinus radiographical bone gain after 4 years of functional loading. The premolar implant site presented a starting basal bone height of 6 mm, while the molar site was of 2 mm. In the first surgical step, sinus floor elevation was performed mesially and the implant was inserted, and distally only sinus floor elevation was performed. After 6 months, the mesial implant was uncovered and the second implant was inserted; 4 months later, the second fixture was uncovered, and both fixtures were loaded with single provisional screw-retained crowns and later with single screw-retained porcelain fused to metal crowns. Implants integrated successfully, and crestal bone remodelling did not exceed the smooth collar. Bone gain was 3 mm for the mesial implant and more than 5 mm for the distal one.

  16. An elevator

    Energy Technology Data Exchange (ETDEWEB)

    Loginovskiy, V.I.; Medinger, N.V.; Rasskazov, V.A.; Solonitsyn, V.A.

    1983-01-01

    An elevator is proposed which includes a body, spring loaded cams and a shut-off ring. To increase the reliability of the elevator by eliminating the possibility of spontaneous shifting of the shut-off ring, the latter is equipped with handles hinged to it and is made with evolvent grooves. The cams are equipped with rollers installed in the evolvent grooves of the shut off ring, where the body is made with grooves for the handles.

  17. Elevated-temperature tests of simply-supported beams and circular plates subjected to time-varying loadings

    International Nuclear Information System (INIS)

    Corum, J.M.; Richardson, M.

    1975-01-01

    The measured elastic-plastic and elastic-plastic-creep responses of a number of simply-supported type 304 stainless steel beams and circular plates are presented. Beams and plates exhibit the essential features of inelastic structural behavior; yet they are relatively simple. In beams, the stress fields are largely uniaxial, while multiaxial effects are introduced in plates. The specimens were laterally loaded at the center, and the tests were performed by subjecting the specimens to either a prescribed load or center-deflection history. The specimens were machined from a common, well-characterized heat of material, and all of the tests were performed at a temperature of 1100 F. The elastic-plastic tests consisted of short-time cycling of the center load, or deflection, between fixed limits. In the elastic-plastic-creep tests the center load, or deflection, was held constant for periods of time, but was periodically subjected to a step increase or decrease, including reversals. The test results are presented in terms of the load and center-deflection behaviors, which typify the overall structural behavior. (U.S.)

  18. Effects of Loading Frequency on Fatigue Behavior, Residual Stress, and Microstructure of Deep-Rolled Stainless Steel AISI 304 at Elevated Temperatures

    Science.gov (United States)

    Nikitin, I.; Juijerm, P.

    2018-02-01

    The effects of loading frequency on the fatigue behavior of non-deep-rolled (NDR) and deep-rolled (DR) austenitic stainless steel AISI 304 were systematically clarified at elevated temperatures, especially at temperatures exhibiting the dynamic strain aging (DSA) phenomena. Tension-compression fatigue tests were performed isothermally at temperatures of 573 K and 773 K (300 °C and 500 °C) with different loading frequencies of 5, 0.5, 0.05, and 0.005 Hz. For the DR condition, the residual stresses and work-hardening states will be presented. It was found that DSA would be detected at appropriate temperatures and deformation rates. The cyclic deformation curves and the fatigue lives of the investigated austenitic stainless steel AISI 304 are considerably affected by the DSA, especially on the DR condition having high dislocation densities at the surface and in near-surface regions. In the temperature range of the DSA, residual stresses and work-hardening states of the DR condition seem to be stabilized. The microstructural alterations were investigated by transmission electron microscopy (TEM). At an appropriate temperature with low loading frequency, the plastic deformation mechanism shifted from a wavy slip manner to a planar slip manner in the DSA regimes, whereas the dislocation movements were obstructed.

  19. Crack propagation behaviour in stainless steel AISI 316L at elevated temperatures under static and cyclic loading

    International Nuclear Information System (INIS)

    Lange, H.

    1991-01-01

    Experimental investigations of crack growth under creep and creep-fatigue conditions are presented. The experiments were performed with the austenitic steel AISI 316L, that will be used in fast breeder reactors. A comparison of crack propagation behaviour at temperatures of T = 550deg C and T = 700deg C in common through-thickness cracked specimens and in plates containing surface cracks is carried out by application of several fracture mechanics parameters. The quantitative description of crack initiation times and crack velocities is persued particularly. The propagation rate of one-dimensional cracks under cyclic loading conditions at T = 550deg C is also treated with fracture mechanical methods. The influence of the hold periods on crack speed is discussed. (orig.) [de

  20. Exposure to internal muscle tissue loads under the ischial tuberosities during sitting is elevated at abnormally high or low body mass indices.

    Science.gov (United States)

    Sopher, Ran; Nixon, Jane; Gorecki, Claudia; Gefen, Amit

    2010-01-19

    Deep tissue injury (DTI) is a severe pressure ulcer characteristic of chairfast or bedfast individuals, such as those with impaired mobility or neurological disorders. A DTI differs from superficial pressure ulcers in that the onset of DTI occurs under intact skin, in skeletal muscle tissue overlying bony prominences, and progression of the wound continues subcutaneously until skin breakdown. Due to the nature of this silently progressing wound, it is highly important to screen potentially susceptible individuals for their risk of developing a DTI. Abnormally low and high values of the body mass index (BMI) have been proposed to be associated with pressure ulcers, but a clear mechanism is lacking. We hypothesize that during sitting, exposure to internal muscle tissue loads under the ischial tuberosities (IT) is elevated at abnormally high or low body mass indices. Our aims in this study were: (a) to develop biomechanical models of the IT region in the buttocks that represent an individual who is gaining or losing weight drastically. (b) To determine changes in internal tissue load measures: principal compression strain, strain energy density (SED), principal compression stress and von Mises stress versus the BMI. (c) To determine percentage volumes of muscle tissue exposed to critical levels of the above load measures, which were defined based on our previous animal and tissue engineered model experiments: strain>or=50%, stress>or=2 kPa, SED>or=0.5 kPa. A set of 21 finite element models, which represented the same individual, but with different BMI values within the normal range, above it and below it, was solved for the outcome measures listed above. The models had the same IT shape, size, distance between the IT, and (non-linear) mechanical properties for all soft tissues, but different thicknesses of gluteus muscles and fat tissue layers, corresponding to the BMI level. The resulted data indicated a trend of progressive increase in internal tissue loading

  1. Elevating your elevator talk

    Science.gov (United States)

    An important and often overlooked item that every early career researcher needs to do is compose an elevator talk. The elevator talk, named because the talk should not last longer than an average elevator ride (30 to 60 seconds), is an effective method to present your research and yourself in a clea...

  2. [PALEOPATHOLOGY OF HUMAN REMAINS].

    Science.gov (United States)

    Minozzi, Simona; Fornaciari, Gino

    2015-01-01

    Many diseases induce alterations in the human skeleton, leaving traces of their presence in ancient remains. Paleopathological examination of human remains not only allows the study of the history and evolution of the disease, but also the reconstruction of health conditions in the past populations. This paper describes the most interesting diseases observed in skeletal samples from the Roman Imperial Age necropoles found in urban and suburban areas of Rome during archaeological excavations in the last decades. The diseases observed were grouped into the following categories: articular diseases, traumas, infections, metabolic or nutritional diseases, congenital diseases and tumours, and some examples are reported for each group. Although extensive epidemiological investigation in ancient skeletal records is impossible, the palaeopathological study allowed to highlight the spread of numerous illnesses, many of which can be related to the life and health conditions of the Roman population.

  3. Endogenous substance P production in the Achilles tendon increases with loading in an in vivo model of tendinopathy-peptidergic elevation preceding tendinosis-like tissue changes.

    Science.gov (United States)

    Backman, L J; Andersson, G; Wennstig, G; Forsgren, S; Danielson, P

    2011-06-01

    To quantify the intratendinous levels of substance P (SP) at different stages of overload in an established model for Achilles tendinopathy (rabbit). Also, to study the distribution of the SP-receptor, the NK-1R, and the source of SP, in the tendon. Animals were subjected to the overuse protocol for 1, 3 or 6 weeks. One additional group served as unexercised controls. Immunoassay (EIA), immunohistochemistry (IHC), and in situ hybridisation (ISH) were performed. EIA revealed increased SP-levels in the Achilles tendon of the exercised limb in all the experimental groups as compared to in the controls (statistically significant; p=0.01). A similar trend in the unexercised Achilles tendon was observed but was not statistically significant (p=0.14). IHC and in ISH illustrated reactions of both SP and NK-1R mainly in blood vessel walls, but the receptor was also found on tenocytes. Achilles tendon SP-levels are elevated already after 1 week of loading. This shows that increased SP-production precedes tendinosis, as tendinosis-like changes occur only after a minimum of 3 weeks of exercise, as shown in a recent study using this model. We propose that central neuronal mechanism may be involved as similar trends were observed in the contralateral Achilles tendon.

  4. An elevator

    Energy Technology Data Exchange (ETDEWEB)

    Gusev, A.S.; Peshkov, L.P.; Rozin, M.M.; Shestov, A.G.

    1983-01-01

    An elevator is proposed which includes a body, a flap, a lock with a catch and a spring-loaded shut-off clamp in the form of upper and lower horizontal levers which are connected by a handle and an axle and one end of which is made in the form of an eccentric cam. The size of the eccentricity of the cam of the levers is increased toward the handle of the clamp in order to increase the operational reliability and to extend the service life.

  5. An elevator

    Energy Technology Data Exchange (ETDEWEB)

    Rastorguyev, M.A.; Maloyarovslavtesv, D.A.; Prokopov, O.I.; Tukayev, Sh.V.; Zanilov, I.F.

    1983-01-01

    An elevator is proposed which includes a body with a turning collar locking device and a rod with longitudinal grooves, which are flexibly linked with jaws positioned in grooves in the body. To increase safety through ensuring automatic locking of the jaws in the closed position, the locking device is made in the form of head on wedges, spring loaded relative to the collar and made with cams and positioned with the capability of interacting with the grooves of the rod and through the cams with the collar.

  6. Elevated temperature fracture mechanics

    International Nuclear Information System (INIS)

    Tomkins, B.

    1979-01-01

    The application of fracture mechanics concepts to cracks at elevated temperatures is examined. Particular consideration is given to the characterisation of crack tip stress-strain fields and parameters controlling crack extension under static and cyclic loads. (author)

  7. Children with Elevated Psychosocial Risk Load Benefit Most from a Family-Based Preventive Intervention: Exploratory Differential Analyses from the German "Strengthening Families Program 10-14" Adaptation Trial.

    Science.gov (United States)

    Bröning, Sonja; Baldus, Christiane; Thomsen, Monika; Sack, Peter-Michael; Arnaud, Nicolas; Thomasius, Rainer

    2017-11-01

    While the effectiveness of substance use prevention programs such as the Strengthening Families Program 10-14 (SFP) has been demonstrated in the USA, European SFP adaptations have not replicated these sizable effects. Following the rationale of the risk moderation hypothesis positing that elevated risk groups may benefit more from a preventive intervention than lower-risk groups, we reanalyzed evaluation data from a randomized controlled trial testing the adapted German version of SFP (SFP-D). We hypothesized a differential impact of risk status on intervention results. The study employed a minimal control condition. Of the N = 292 participating children, 73.5% qualified as at-risk because they lived in a deprived urban district, and 26.5% qualified as high risk because they additionally scored as "difficult" in the German Strengths and Difficulty Questionnaire (parents' reports using gender- and age-specific German norms). Outcomes were children's self-reports on substance use, mental health, family functioning, and quality of life. Data were analyzed with repeated measures linear mixed models and relative risk analyses. The high-risk group in the SFP-D condition achieved the best results compared with all other groups, especially in mental health and quality of life. Relative risk analyses on tobacco [alcohol] abstinence showed that an additional percentage of 29.8% [16.0%] of high-risk children in nonabstinent controls would have remained abstinent if they had participated in SFP-D. We conclude that risk load influences the impact of substance use prevention programs and discuss to what extent differential analyses can add value to prevention research.

  8. Effects of moisture, elevated temperature, and fatigue loading on the behavior of graphite/epoxy buffer strip panels with center cracks

    Science.gov (United States)

    Bigelow, C. A.

    1988-01-01

    The effects of fatigue loading combined with moisture and heat on the behavior of graphite epoxy panels with either Kevlar-49 or S-glass buffer strips were studied. Buffer strip panels, that had a slit in the center to represent damage, were moisture conditioned or heated, fatigue loaded, and then tested in tension to measure their residual strength. The buffer strips were parallel to the loading direction and were made by replacing narrow strips of the 0 deg graphite plies with Kevlar-49 epoxy or S-glass epoxy on a 1-for-1 basis. The panels were subjected to a fatigue loading spectrum. One group of panels was preconditioned by soaking in 60 C water to produce a 1 percent weight gain then tested at room temperature. One group was heated to 82 C during the fatigue loading. Another group was moisture conditioned and then tested at 82 C. The residual strengths of the buffer panels were not highly affected by the fatigue loading, the number of repetitions of the loading spectrum, or the maximum strain level. The moisture conditioning reduced the residual strengths of the S-glass buffer strip panel by 10 to 15 percent below the ambient results. The moisture conditioning did not have a large effect on the Kevlar-49 panels.

  9. Complex behavior of elevators in peak traffic

    Science.gov (United States)

    Nagatani, Takashi

    2003-08-01

    We study the dynamical behavior of elevators in the morning peak traffic. We present a stochastic model of the elevators to take into account the interactions between elevators through passengers. The dynamics of the elevators is expressed in terms of a coupled nonlinear map with noises. The number of passengers carried by an elevator and the time-headway between elevators exhibit the complex behavior with varying elevator trips. It is found that the behavior of elevators exhibits a deterministic chaos even if there are no noises. The chaotic motion depends on the loading parameter, the maximum capacity of an elevator, and the number of elevators. When the loading parameter is superior to the threshold, each elevator carries a full load of passengers throughout its trip. The dependence of the threshold (transition point) on the elevator capacity is clarified.

  10. Temporal changes in stored-product insect populations associated with boot, pit, and load-out areas of grain elevators and feed mills

    Science.gov (United States)

    Commercial grain elevator and feed mill facilities can quickly become infested with stored-product insect pests, compromising the protection of the raw and processed cereal products stored at each facility type. Grain facilities of each type were sampled monthly for adults of stored-product insects ...

  11. Analysis of presented fissures in the axes of traction of the elevators of passengers of load; Analisis de fisuras presentadas en los ejes de traccion de los elevadores de pasajeros o carga

    Energy Technology Data Exchange (ETDEWEB)

    Nieto Miranda, J. Jesus; Paredes Rueda, Miguel Angel; Bernardo Sanchez, Pedro Nicolas [Instituto Tecnologico de Tlalnepantla, Estado de Mexico (Mexico)

    2003-04-15

    In this paper is presented the procedure and analysis of the control by applied in the detection of fissures in the axis of the traction machine used in the elevators of passengers or load. The stresses by flexion that are generated in such axis, due to the loads that it supports, are determined and analyzed. In such analysis is used the method of the finite element and the computation program ANSYS 5.5. Both techniques are conjugated to verify the mechanical state of the axis, to guarantee their structural integrity during the operation of the elevator. [Spanish] En este trabajo se presenta el procedimiento y analisis del control por ultrasonido aplicado en la deteccion de fisuras originadas en el eje de las maquinas de traccion que utilizan los elevadores de pasajeros o carga. Los esfuerzos por flexion que se generan en dicho eje, ocasionados por las cargas que soporta, se determinan y analizan por el metodo del elemento finito y el programa de computo ANSYS 5.5. Ambas tecnicas se conjugan para verificar el estado mecanico del eje, con el fin de garantizar su integridad estructural durante el funcionamiento del elevador.

  12. Inelastic behavior of modified 9Cr-1 Mo steel under basic loading conditions at elevated temperature and evaluation of two unified constitutive models

    International Nuclear Information System (INIS)

    Tanaka, Eiichi; Mizuno, Mamoru.

    1993-01-01

    The purposes of this paper are to elucidate fundamental material properties of modified 9Cr-1 Mo steel as a candidate material for next-generation fast breeder reactors and to obtain information for the formulation of a practical unified constitutive model. For these purposes, monotonous tension, uniaxial symmetric cycles, uniaxial symmetric cycles with hold time, creep, stress control uniaxial symmetric cycles, cyclic relaxation and circular cyclic loading tests are performed. Then these results are simulated by two unified constitutive models, i.e. the Chaboche model and Bodner-Partom model. The results of simulation show that the Chaboche model can describe all the experimental results with relatively high accuracy, and that the identification of material constants of the model is easy. The Bodner-Partom model can similarly describe the results, but the determination of material constants is difficult. (author)

  13. Effect of plasma spraying parameter on wear resistance of NiCrBSiCFe plasma coatings on austenitic stainless steel at elevated temperatures at various loads

    International Nuclear Information System (INIS)

    Parthasarathi, N.L.; Duraiselvam, Muthukannan; Borah, Utpal

    2012-01-01

    Highlights: ► Effect of plasma spraying parameters, especially the stand-off distance. ► Effect of microstructure and applied load on coating in sliding wear. ► The reason for maximum wear rate at 250 °C and the minimum wear at 350 °C were explained. ► The worn debris were characterised by SEM analysis and correlated with wear rate. -- Abstract: The dry sliding wear tests were carried out on AISI 316 austenitic stainless steel (ASS) plasma coated with NiCrBSiCFe alloy powder under two set of plasma spraying parameters (PSP-1 and PSP-2). EN 8 medium carbon steel was used as a counterface material. The tests were carried out at loads of 20 N and 40 N with a constant sliding velocity of 1 m/s at room temperature (35°), 150 °C, 250 °C and 350 °C. Metallographic characterisation was carried out by optical microscope (OM), scanning electron microscope (SEM) and X-ray diffraction (XRD). Between the two plasma parameters tested, stand-off distance of 125 mm was found to be more suitable for producing uniform lamellar microstructure with fewer amounts of pores which shows better wear resistance. The wear rate at 250 °C was comparatively more due to the material softening and adhesion by intermolecular bonding. The worn debris collected during sliding at 350 °C turn into oxides which further behaves like a protective and lubricative film eliminating the chances of severe material loss. SEM was used to characterise the worn track and debris to identity the wear mechanism.

  14. In-situ X-ray residual stress measurement on a peened alloy 600 weld metal at elevated temperature under tensile load

    International Nuclear Information System (INIS)

    Yunomura, Tomoaki; Maeguchi, Takaharu; Kurimura, Takayuki

    2014-01-01

    In order to verify stability of residual stress improvement effect of peeing for mitigation of stress corrosion cracking in components of PWR plant, relaxation behavior of residual stress induced by water jet peening (WJP) on surface of alloy 600 weld metal (alloy 132) was investigated by in-situ X-ray residual stress measurement under thermal aging and stress condition considered for actual plant operation. Surface residual stress change was observed at the early stage of thermal aging at 360°C, but no significant further stress relaxation was observed after that. Applied stress below yield stress does not significantly affect stress relaxation behavior of surface residual stress. For the X-ray residual stress measurement, X-ray stress constant at room temperature for alloy 600 was determined experimentally with several surface treatment and existence of applied strain. The X-ray stress constant at elevated temperatures were extrapolated theoretically based on the X-ray stress constant at room temperature for alloy 600. (author)

  15. Data Elevator

    Energy Technology Data Exchange (ETDEWEB)

    2017-04-29

    Data Elevator: Efficient Asynchronous Data Movement in Hierarchical Storage Systems Multi-layer storage subsystems, including SSD-based burst buffers and disk-based parallel file systems (PFS), are becoming part of HPC systems. However, software for this storage hierarchy is still in its infancy. Applications may have to explicitly move data among the storage layers. We propose Data Elevator for transparently and efficiently moving data between a burst buffer and a PFS. Users specify the final destination for their data, typically on PFS, Data Elevator intercepts the I/O calls, stages data on burst buffer, and then asynchronously transfers the data to their final destination in the background. This system allows extensive optimizations, such as overlapping read and write operations, choosing I/O modes, and aligning buffer boundaries. In tests with large-scale scientific applications, Data Elevator is as much as 4.2X faster than Cray DataWarp, the start-of-art software for burst buffer, and 4X faster than directly writing to PFS. The Data Elevator library uses HDF5's Virtual Object Layer (VOL) for intercepting parallel I/O calls that write data to PFS. The intercepted calls are redirected to the Data Elevator, which provides a handle to write the file in a faster and intermediate burst buffer system. Once the application finishes writing the data to the burst buffer, the Data Elevator job uses HDF5 to move the data to final destination in an asynchronous manner. Hence, using the Data Elevator library is currently useful for applications that call HDF5 for writing data files. Also, the Data Elevator depends on the HDF5 VOL functionality.

  16. Monocular Elevation Deficiency - Double Elevator Palsy

    Science.gov (United States)

    ... Español Condiciones Chinese Conditions Monocular Elevation Deficiency/ Double Elevator Palsy En Español Read in Chinese What is monocular elevation deficiency (Double Elevator Palsy)? Monocular Elevation Deficiency, also known by the ...

  17. And the Dead Remain Behind

    Directory of Open Access Journals (Sweden)

    Peter Read

    2013-08-01

    Full Text Available In most cultures the dead and their living relatives are held in a dialogic relationship. The dead have made it clear, while living, what they expect from their descendants. The living, for their part, wish to honour the tombs of their ancestors; at the least, to keep the graves of the recent dead from disrepair. Despite the strictures, the living can fail their responsibilities, for example, by migration to foreign countries. The peripatetic Chinese are one of the few cultures able to overcome the dilemma of the wanderer or the exile. With the help of a priest, an Australian Chinese migrant may summon the soul of an ancestor from an Asian grave to a Melbourne temple, where the spirit, though removed from its earthly vessel, will rest and remain at peace. Amongst cultures in which such practices are not culturally appropriate, to fail to honour the family dead can be exquisitely painful. Violence is the cause of most failure.

  18. Red Assembly: the work remains

    Directory of Open Access Journals (Sweden)

    Leslie Witz

    installed. What to do at this limit, at the transgressive encounter between saying yes and no to history, remains the challenge. It is the very challenge of what insistently remains.

  19. Green business will remain green

    International Nuclear Information System (INIS)

    Marcan, P.

    2008-01-01

    It all started with two words. Climate change. The carbon dioxide trading scheme, which was the politicians' idea on solving the number one global problem, followed. Four years ago, when the project was begun, there was no data for project initiation. Quotas for polluters mainly from energy production and other energy demanding industries were distributed based on spreadsheets, maximum output and expected future development of economies. Slovak companies have had a chance to profit from these arrangements since 2005. Many of them took advantage of the situation and turned the excessive quotas into an extraordinary profit which often reached hundreds of million Sk. The fact that the price of free quotas offered for sale dropped basically to 0 in 2006 only proved that the initial distribution was too generous. And the market reacted to the first official measurements of emissions. Slovak companies also contributed to this development. However, when planning the maximum emission volumes for 2008-2012 period, in spite of the fact that actual data were available, their expectations were not realistic. A glance at the figures in the proposal of the Ministry of Environment is sufficient to realize that there will be no major change in the future. And so for many Slovak companies business with a green future will remain green for the next five years. The state decided to give to selected companies even more free space as far as emissions are concerned. The most privileged companies can expect quotas increased by tens of percent. (author)

  20. Elevator and hydraulics; Elevator to yuatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, I. [Hitachi, Ltd., Tokyo (Japan)

    1994-07-15

    A hydraulic type elevator is installed in relatively lower buildings as compared with a rope type elevator, but the ratio in the number of installation of the former elevator is increasing. This paper explains from its construction and features to especially various control systems for the riding comfort and safety. A direct push-up system with hydraulic jacks arranged beneath a car, and an indirect push-up system that has hydraulic jacks arranged on flank of a car and transmits the movement of a plunger via a rope are available. The latter system eliminates the need of large holes to embed hydraulic jacks. While the speed is controlled by controlling flow rates of high-pressure oil, the speed, position, acceleration and even time differential calculus of the acceleration must be controlled severely. The system uses two-step control for the through-speed and the landing speed. Different systems that have been realized may include compensation for temperatures in flow rate control valves, load pressures, and oil viscosity, from learning control to fuzzy control for psychological effects, or control of inverters in motors. 13 refs., 12 figs., 1 tab.

  1. Silicon photonics: some remaining challenges

    Science.gov (United States)

    Reed, G. T.; Topley, R.; Khokhar, A. Z.; Thompson, D. J.; Stanković, S.; Reynolds, S.; Chen, X.; Soper, N.; Mitchell, C. J.; Hu, Y.; Shen, L.; Martinez-Jimenez, G.; Healy, N.; Mailis, S.; Peacock, A. C.; Nedeljkovic, M.; Gardes, F. Y.; Soler Penades, J.; Alonso-Ramos, C.; Ortega-Monux, A.; Wanguemert-Perez, G.; Molina-Fernandez, I.; Cheben, P.; Mashanovich, G. Z.

    2016-03-01

    This paper discusses some of the remaining challenges for silicon photonics, and how we at Southampton University have approached some of them. Despite phenomenal advances in the field of Silicon Photonics, there are a number of areas that still require development. For short to medium reach applications, there is a need to improve the power consumption of photonic circuits such that inter-chip, and perhaps intra-chip applications are viable. This means that yet smaller devices are required as well as thermally stable devices, and multiple wavelength channels. In turn this demands smaller, more efficient modulators, athermal circuits, and improved wavelength division multiplexers. The debate continues as to whether on-chip lasers are necessary for all applications, but an efficient low cost laser would benefit many applications. Multi-layer photonics offers the possibility of increasing the complexity and effectiveness of a given area of chip real estate, but it is a demanding challenge. Low cost packaging (in particular, passive alignment of fibre to waveguide), and effective wafer scale testing strategies, are also essential for mass market applications. Whilst solutions to these challenges would enhance most applications, a derivative technology is emerging, that of Mid Infra-Red (MIR) silicon photonics. This field will build on existing developments, but will require key enhancements to facilitate functionality at longer wavelengths. In common with mainstream silicon photonics, significant developments have been made, but there is still much left to do. Here we summarise some of our recent work towards wafer scale testing, passive alignment, multiplexing, and MIR silicon photonics technology.

  2. Elevator wheel

    Energy Technology Data Exchange (ETDEWEB)

    Zhornik, V.I.; Cherkov, Ye.M.; Simonov, A.A.

    1982-01-01

    An elevator wheel is suggested for unloading a sunken product from a bath of a heavy-average separator including discs of a bucket with inner walls, and covering sheets hinged to the buckets. In order to improve the degree of dehydration of the removed product, the inner wall of each bucket is made of sheets installed in steps with gaps of one in relation to the other.

  3. Bucket elevator

    OpenAIRE

    Chromek, Jiří

    2013-01-01

    Cílem této bakalářské práce je návrh svislého korečkového elevátoru, který má sloužit k dopravě obilovin s dopravní výškou 19 m a dopravovaným množstvím 100 t/hod. Práce se skládá z popisu korečkového elevátoru a jeho hlavních částí, zmiňující se v úvodní rešerši. Tato práce je zaměřena na funkční a kapacitní výpočet, určení pohonu a napínacího zařízení. Další výpočet je kontrolní, skládající se z pevnostní kontroly hnacího hřídele, výpočtu pera, životnosti ložisek a výpočtu napínacího zaříze...

  4. Relaxation of Shot-Peened Residual Stresses Under Creep Loading (Preprint)

    National Research Council Canada - National Science Library

    Buchanan, Dennis J; John, Reji; Brockman, Robert A

    2008-01-01

    .... Compressive residual stresses retard initiation and growth of fatigue cracks. During the component loading history, loading, or during elevated temperature static loading, such as thermal exposure and creep...

  5. HCF + LCF Interactions at Elevated Temperature

    National Research Council Canada - National Science Library

    Byrne, James; Hall, R. F; Ding, J

    2005-01-01

    ...) crack propagation in Ti- 6Al-4V will be studied under combined HCF/low cycle fatigue (LCF) loading conditions at elevated temperatures up to 350 deg C where creep stress ratcheting and environmental effects may arise...

  6. On use of radial evanescence remain term in kinematic hardening

    International Nuclear Information System (INIS)

    Geyer, P.

    1995-10-01

    A fine modelling of the material' behaviour can be necessary to study the mechanical strength of nuclear power plant' components under cyclic loads. Ratchetting is one of the last phenomena for which numerical models have to be improved. We discuss in this paper on use of radial evanescence remain term in kinematic hardening to improve the description of ratchetting in biaxial loading tests. It's well known that Chaboche elastoplastic model with two non linear kinematic hardening variables initially proposed by Armstrong and Frederick, usually over-predicts accumulation of ratchetting strain. Burlet and Cailletaud proposed in 1987 a non linear kinematic rule with a radial evanescence remain term. The two models lead to identical formulation for proportional loadings. In the case of a biaxial loading test (primary+secondary loading), Burlet and Cailletaud model leads to accommodation, when Chaboche one's leads to ratchetting with a constant increment of strain. So we can have an under-estimate with the first model and an over-estimate with the second. An easy method to improve the description of ratchetting is to combine the two kinematic rules. Such an idea is already used by Delobelle in his model. With analytical results in the case of tension-torsion tests, we show in a first part of the paper, the interest of radial evanescence remain term in the non linear kinematic rule to describe ratchetting: we give the conditions to get adaptation, accommodation or ratchetting and the value of the strain increment in the last case. In the second part of the paper, we propose to modify the elastoplastic Chaboche model by coupling the two types of hardening by means of two scalar parameters which can be identified independently on biaxial loading tests. Identification of these two parameters returns to speculate on the directions of strain in order to adjust the ratchetting to experimental observations. We use the experimental results on the austenitic steel 316L at room

  7. A new pressure chamber to study the biosynthetic response of articular cartilage to mechanical loading.

    Science.gov (United States)

    Steinmeyer, J; Torzilli, P A; Burton-Wurster, N; Lust, G

    1993-01-01

    A prototype chamber was used to apply a precise cyclic or static load on articular cartilage explants under sterile conditions. A variable pressure, pneumatic controller was constructed to power the chamber's air cylinder, capable of applying, with a porous load platen, loads of up to 10 MPa at cycles ranging from 0 to 10 Hz. Pig articular cartilage explants were maintained successfully in this chamber for 2 days under cyclic mechanical loading of 0.5 Hz, 0.5 MPa. Explants remained sterile, viable and metabolically active. Cartilage responded to this load with a decreased synthesis of fibronectin and a small but statistically significant elevation in proteoglycan content. Similar but less extensive effects on fibronectin synthesis were observed with the small static load (0.016 MPa) inherent in the design of the chamber.

  8. Energy efficient elevators and escalators

    Energy Technology Data Exchange (ETDEWEB)

    Patrao, Carlos; Fong, Joao; Almeida, Anibal de (Dep. Electrical Engineering, Univ. of Coimbra, Coimbra (Portugal)); Rivet, Luc

    2009-07-01

    Elevators and escalators are the crucial element that makes it practical to live and work several floors above ground - more than 4,3 million units are installed in Europe. Due to ageing of the European population the installation of elevators in single family houses is experiencing a significant growth, as well as equipping existing buildings. Elevators use about 4% of the electricity in tertiary sector buildings. High untapped saving potentials exist with respect to energy-efficient technologies, investment decisions and behavioural approaches, in these sectors. This paper presents preliminary results from the IEE project E4, whose overall objective is the improvement of the energy performance of elevators and escalators, in tertiary sector buildings and in multi family residential buildings. The project is characterizing people conveyors electricity consumption in the tertiary sector and in residential buildings in the EU. The installed park is characterised by a survey among elevators national associations in each country. An assessment of the barriers has been made in the first phase of the project and will be presented. Monitoring campaigns in elevators and escalators are being conducted in each country according to a common developed methodology. More than fifty elevators and escalators will be audited. This will allow the collection of load curves (start up, travel up and down, travel full and empty), including the characterization of standby consumption. Standby consumption of an elevator can represent up to 80% of the total energy consumed per year, and can be drastically reduced. This paper presents the preliminary results of the first ten audits performed in Portugal by Isr-UC.

  9. National Elevation Dataset (NED)

    Data.gov (United States)

    Kansas Data Access and Support Center — The U.S. Geological Survey has developed a National Elevation Database (NED). The NED is a seamless mosaic of best-available elevation data. The 7.5-minute elevation...

  10. Elevated Liver Enzymes

    Science.gov (United States)

    Symptoms Elevated liver enzymes By Mayo Clinic Staff Elevated liver enzymes may indicate inflammation or damage to cells in the liver. Inflamed or ... than normal amounts of certain chemicals, including liver enzymes, into the bloodstream, which can result in elevated ...

  11. Remaining life assessment of a high pressure turbine rotor

    International Nuclear Information System (INIS)

    Nguyen, Ninh; Little, Alfie

    2012-01-01

    This paper describes finite element and fracture mechanics based modelling work that provides a useful tool for evaluation of the remaining life of a high pressure (HP) steam turbine rotor that had experienced thermal fatigue cracking. An axis-symmetrical model of a HP rotor was constructed. Steam temperature, pressure and rotor speed data from start ups and shut downs were used for the thermal and stress analysis. Operating history and inspection records were used to benchmark the damage experienced by the rotor. Fracture mechanics crack growth analysis was carried out to evaluate the remaining life of the rotor under themal cyclic loading conditions. The work confirmed that the fracture mechanics approach in conjunction with finite element modelling provides a useful tool for assessing the remaining life of high temperature components in power plants.

  12. Fish remains and humankind: part two

    Directory of Open Access Journals (Sweden)

    Andrew K G Jones

    1998-07-01

    Full Text Available The significance of aquatic resources to past human groups is not adequately reflected in the published literature - a deficiency which is gradually being acknowledged by the archaeological community world-wide. The publication of the following three papers goes some way to redress this problem. Originally presented at an International Council of Archaeozoology (ICAZ Fish Remains Working Group meeting in York, U.K. in 1987, these papers offer clear evidence of the range of interest in ancient fish remains across the world. Further papers from the York meeting were published in Internet Archaeology 3 in 1997.

  13. Plutonium Immobilization Can Loading Preliminary Specifications

    Energy Technology Data Exchange (ETDEWEB)

    Kriikku, E.

    1998-11-25

    This report discusses the Plutonium Immobilization can loading preliminary equipment specifications and includes a process block diagram, process description, equipment list, preliminary equipment specifications, plan and elevation sketches, and some commercial catalogs. This report identifies loading pucks into cans and backfilling cans with helium as the top priority can loading development areas.

  14. Why Agricultural Educators Remain in the Classroom

    Science.gov (United States)

    Crutchfield, Nina; Ritz, Rudy; Burris, Scott

    2013-01-01

    The purpose of this study was to identify and describe factors that are related to agricultural educator career retention and to explore the relationships between work engagement, work-life balance, occupational commitment, and personal and career factors as related to the decision to remain in the teaching profession. The target population for…

  15. Juveniles' Motivations for Remaining in Prostitution

    Science.gov (United States)

    Hwang, Shu-Ling; Bedford, Olwen

    2004-01-01

    Qualitative data from in-depth interviews were collected in 1990-1991, 1992, and 2000 with 49 prostituted juveniles remanded to two rehabilitation centers in Taiwan. These data are analyzed to explore Taiwanese prostituted juveniles' feelings about themselves and their work, their motivations for remaining in prostitution, and their difficulties…

  16. Kadav Moun PSA (:60) (Human Remains)

    Centers for Disease Control (CDC) Podcasts

    2010-02-18

    This is an important public health announcement about safety precautions for those handling human remains. Language: Haitian Creole.  Created: 2/18/2010 by Centers for Disease Control and Prevention (CDC).   Date Released: 2/18/2010.

  17. The Annuity Puzzle Remains a Puzzle

    NARCIS (Netherlands)

    Peijnenburg, J.M.J.; Werker, Bas; Nijman, Theo

    We examine incomplete annuity menus and background risk as possible drivers of divergence from full annuitization. Contrary to what is often suggested in the literature, we find that full annuitization remains optimal if saving is possible after retirement. This holds irrespective of whether real or

  18. Randomized controlled multicenter study comparing short dental implants (6 mm) versus longer dental implants (11-15 mm) in combination with sinus floor elevation procedures. Part 2: clinical and radiographic outcomes at 1 year of loading.

    Science.gov (United States)

    Schincaglia, Gian Pietro; Thoma, Daniel S; Haas, Robert; Tutak, Marcin; Garcia, Abel; Taylor, Thomas D; Hämmerle, Christoph H F

    2015-11-01

    To compare, clinically and radiographically, short dental implants (6 mm) to long implants (11-15 mm) placed with sinus grafting. Participants with 5-7 mm of bone height in the posterior maxilla were randomly allocated to receive short implants (GS) or long implants with sinus grafting (GG). Implants were loaded with single crowns 6 months after placement (PR). Patients were re-evaluated 12 months after loading (FU-1). Outcome variables included: Implant survival rate (CSR), marginal bone level alteration (MBL), periodontal probing depth (PPD), bleeding on probing (BoP), plaque control record (PCR) and crown-to-implant ratios (C/I). Statistical analysis was performed using parametric tests. In 97 subjects, 132 implants were re-evaluated at FU-1. The CSR was 100%. The MBL from implant placement (IP) to (PR) was -0.22 ± 0.4 mm for GG and -0.3 ± 0.45 mm for GS (p 0.05), PPD (p = 1) and PCR (p = 0.09). BoP was higher in the GS (p = 0.04). The C/I was 0.99 ± 0.17 for GG and 1.86 ± 0.23 for GS (p < 0.001). No correlation was observed between C/I and MBL, (GG: p = 0.13; GS: p = 0.38). Both treatment modalities provided similar outcomes. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  19. The space station tethered elevator system

    Science.gov (United States)

    Anderson, Loren A.

    1989-01-01

    The optimized conceptual engineering design of a space station tethered elevator is presented. The elevator is an unmanned mobile structure which operates on a ten kilometer tether spanning the distance between the Space Station and a tethered platform. Elevator capabilities include providing access to residual gravity levels, remote servicing, and transportation to any point along a tether. The potential uses, parameters, and evolution of the spacecraft design are discussed. Engineering development of the tethered elevator is the result of work conducted in the following areas: structural configurations; robotics, drive mechanisms; and power generation and transmission systems. The structural configuration of the elevator is presented. The structure supports, houses, and protects all systems on board the elevator. The implementation of robotics on board the elevator is discussed. Elevator robotics allow for the deployment, retrieval, and manipulation of tethered objects. Robotic manipulators also aid in hooking the elevator on a tether. Critical to the operation of the tethered elevator is the design of its drive mechanisms, which are discussed. Two drivers, located internal to the elevator, propel the vehicle along a tether. These modular components consist of endless toothed belts, shunt-wound motors, regenerative power braking, and computer controlled linear actuators. The designs of self-sufficient power generation and transmission systems are reviewed. Thorough research indicates all components of the elevator will operate under power provided by fuel cells. The fuel cell systems will power the vehicle at seven kilowatts continuously and twelve kilowatts maximally. A set of secondary fuel cells provides redundancy in the unlikely event of a primary system failure. Power storage exists in the form of Nickel-Hydrogen batteries capable of powering the elevator under maximum loads.

  20. Explosives remain preferred methods for platform abandonment

    International Nuclear Information System (INIS)

    Pulsipher, A.; Daniel, W. IV; Kiesler, J.E.; Mackey, V. III

    1996-01-01

    Economics and safety concerns indicate that methods involving explosives remain the most practical and cost-effective means for abandoning oil and gas structures in the Gulf of Mexico. A decade has passed since 51 dead sea turtles, many endangered Kemp's Ridleys, washed ashore on the Texas coast shortly after explosives helped remove several offshore platforms. Although no relationship between the explosions and the dead turtles was ever established, in response to widespread public concern, the US Minerals Management Service (MMS) and National Marine Fisheries Service (NMFS) implemented regulations limiting the size and timing of explosive charges. Also, more importantly, they required that operators pay for observers to survey waters surrounding platforms scheduled for removal for 48 hr before any detonations. If observers spot sea turtles or marine mammals within the danger zone, the platform abandonment is delayed until the turtles leave or are removed. However, concern about the effects of explosives on marine life remains

  1. Iowa Bedrock Surface Elevation

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — This Digital Elevation Model (DEM) of the bedrock surface elevation in Iowa was compiled using all available data, principally information from GEOSAM, supplemented...

  2. US nuclear power remains on hold

    International Nuclear Information System (INIS)

    Ahearne, J.F.

    1996-01-01

    The Tennessee Valley Authority's decision to end its nuclear program signaled the end of an era for the nuclear industry in the United States. Despite significant improvements in operational efficiency, nuclear power plants have not proven to be cost-efficient, says John F. Ahearne, executive director of Sigma Xi, The Scientific Research Society, in Research Triangle Park, North Carolina. A decade ago, Ahearne suspected that recovery of the nuclear power industry would depend on increasing demand for energy, a solution to the waste management problem, an unblemished safety record, and competent management. But for utility executives and public officials, the question whether to go nuclear comes down to the question of cost. Despite concerns about greenhouse gasses produced from traditional fossil-fuel plants, even the Environmental Protection Agency recommends sources of energy other than nuclear, says Ahearne. And even if the perennial problem of waste disposal were to be resolved tomorrow, Ahearne says, it is unlikely that utility executives would be scrambling to order new plants. open-quotes For now and into the forseeable future, electricity demand in the United States can be met by conservation, load management, and non-nuclear sources of energy, Ahearne predicts

  3. Decomposition Technique for Remaining Useful Life Prediction

    Science.gov (United States)

    Saha, Bhaskar (Inventor); Goebel, Kai F. (Inventor); Saxena, Abhinav (Inventor); Celaya, Jose R. (Inventor)

    2014-01-01

    The prognostic tool disclosed here decomposes the problem of estimating the remaining useful life (RUL) of a component or sub-system into two separate regression problems: the feature-to-damage mapping and the operational conditions-to-damage-rate mapping. These maps are initially generated in off-line mode. One or more regression algorithms are used to generate each of these maps from measurements (and features derived from these), operational conditions, and ground truth information. This decomposition technique allows for the explicit quantification and management of different sources of uncertainty present in the process. Next, the maps are used in an on-line mode where run-time data (sensor measurements and operational conditions) are used in conjunction with the maps generated in off-line mode to estimate both current damage state as well as future damage accumulation. Remaining life is computed by subtracting the instance when the extrapolated damage reaches the failure threshold from the instance when the prediction is made.

  4. Industry remains stuck in a transitional mode

    International Nuclear Information System (INIS)

    Garb, F.A.

    1991-01-01

    The near future for industry remains foggy for several obvious reasons. The shake-up of the Soviet Union and how the pieces will reform remains unclear. How successful efforts are to privatize government oil company operations around the world has yet to be determined. A long sought peace in the Middle East seems to be inching closer, but will this continue? If it does continue, what impact will it have on world energy policy? Will American companies, which are now transferring their attention to foreign E and P, also maintain an interest in domestic activities? Is the U.S. economy really on the upswing? We are told that the worst of the recession is over, but try telling this to thousands of workers in the oil patch who are being released monthly by the big players in domestic operations. This paper reports that 1992 should be a better year than 1991, if measured in opportunity. There are more exploration and acquisition options available, both domestically and internationally, than there have been in years. Probably more opportunities exist than there are players-certainly more than can be funded with current financial resources

  5. Shotgun microbial profiling of fossil remains

    DEFF Research Database (Denmark)

    Der Sarkissian, Clio; Ermini, Luca; Jónsson, Hákon

    2014-01-01

    the specimen of interest, but instead reflect environmental organisms that colonized the specimen after death. Here, we characterize the microbial diversity recovered from seven c. 200- to 13 000-year-old horse bones collected from northern Siberia. We use a robust, taxonomy-based assignment approach...... to identify the microorganisms present in ancient DNA extracts and quantify their relative abundance. Our results suggest that molecular preservation niches exist within ancient samples that can potentially be used to characterize the environments from which the remains are recovered. In addition, microbial...... community profiling of the seven specimens revealed site-specific environmental signatures. These microbial communities appear to comprise mainly organisms that colonized the fossils recently. Our approach significantly extends the amount of useful data that can be recovered from ancient specimens using...

  6. Some remaining problems in HCDA analysis

    International Nuclear Information System (INIS)

    Chang, Y.W.

    1981-01-01

    The safety assessment and licensing of liquid-metal fast breeder reactors (LMFBRs) requires an analysis on the capability of the reactor primary system to sustain the consequences of a hypothetical core-disruptive accident (HCDA). Although computational methods and computer programs developed for HCDA analyses can predict reasonably well the response of the primary containment system, and follow up the phenomena of HCDA from the start of excursion to the time of dynamic equilibrium in the system, there remain areas in the HCDA analysis that merit further analytical and experimental studies. These are the analysis of fluid impact on reactor cover, three-dimensional analysis, the treatment of the perforated plates, material properties under high strain rates and under high temperatures, the treatment of multifield flows, and the treatment of prestressed concrete reactor vessels. The purpose of this paper is to discuss the structural mechanics of HCDA analysis in these areas where improvements are needed

  7. Political, energy events will remain interwoven

    International Nuclear Information System (INIS)

    Jones, D.P.

    1991-01-01

    This paper reports that it is possible to discuss the significance of political and energy events separately, but, in truth, they are intricately interwoven. Furthermore, there are those who will argue that since the two are inseparable, the future is not predictable; so why bother in the endeavor. It is possible that the central point of the exercise may have been missed-yes, the future is unpredictable exclamation point However, the objective of prediction is secondary. The objective of understanding the dynamic forces of change is primary exclamation point With this view of recent history, it is perhaps appropriate to pause and think about the future of the petroleum industry. The future as shaped by political, energy, economic, environmental and technological forces will direct our lives and markets during this decade. Most importantly, what will be the direction that successful businesses take to remain competitive in a global environment? These are interesting issues worthy of provocative thoughts and innovative ideas

  8. Nuclear remains an economic and ecologic asset

    International Nuclear Information System (INIS)

    Le Ngoc, Boris

    2015-01-01

    The author herein outlines the several benefits of nuclear energy and nuclear industry for France. He first outlines that France possesses 97 per cent of de-carbonated electricity thanks to nuclear energy (77 pc) and renewable energies (20 pc, mainly hydraulic), and that renewable energies must be developed in the building and transport sectors to be able to get rid of the environmentally and financially costly fossil energies. He outlines that reactor maintenance and the nuclear fuel cycle industry are fields of technological leadership for the French nuclear industry which is, after motor industry and aircraft industry, the third industrial sector in France. He indicates that nuclear electricity is to remain the most competitive one, and that nuclear energy and renewable energies must not be opposed to it but considered as complementary in the struggle against climate change, i.e. to reduce greenhouse gas emissions and to get rid of the prevalence of fossil energies

  9. Population cycles: generalities, exceptions and remaining mysteries

    Science.gov (United States)

    2018-01-01

    Population cycles are one of nature's great mysteries. For almost a hundred years, innumerable studies have probed the causes of cyclic dynamics in snowshoe hares, voles and lemmings, forest Lepidoptera and grouse. Even though cyclic species have very different life histories, similarities in mechanisms related to their dynamics are apparent. In addition to high reproductive rates and density-related mortality from predators, pathogens or parasitoids, other characteristics include transgenerational reduced reproduction and dispersal with increasing-peak densities, and genetic similarity among populations. Experiments to stop cyclic dynamics and comparisons of cyclic and noncyclic populations provide some understanding but both reproduction and mortality must be considered. What determines variation in amplitude and periodicity of population outbreaks remains a mystery. PMID:29563267

  10. Does hypertension remain after kidney transplantation?

    Directory of Open Access Journals (Sweden)

    Gholamreza Pourmand

    2015-05-01

    Full Text Available Hypertension is a common complication of kidney transplantation with the prevalence of 80%. Studies in adults have shown a high prevalence of hypertension (HTN in the first three months of transplantation while this rate is reduced to 50- 60% at the end of the first year. HTN remains as a major risk factor for cardiovascular diseases, lower graft survival rates and poor function of transplanted kidney in adults and children. In this retrospective study, medical records of 400 kidney transplantation patients of Sina Hospital were evaluated. Patients were followed monthly for the 1st year, every two months in the 2nd year and every three months after that. In this study 244 (61% patients were male. Mean ± SD age of recipients was 39.3 ± 13.8 years. In most patients (40.8% the cause of end-stage renal disease (ESRD was unknown followed by HTN (26.3%. A total of 166 (41.5% patients had been hypertensive before transplantation and 234 (58.5% had normal blood pressure. Among these 234 individuals, 94 (40.2% developed post-transplantation HTN. On the other hand, among 166 pre-transplant hypertensive patients, 86 patients (56.8% remained hypertensive after transplantation. Totally 180 (45% patients had post-transplantation HTN and 220 patients (55% didn't develop HTN. Based on the findings, the incidence of post-transplantation hypertension is high, and kidney transplantation does not lead to remission of hypertension. On the other hand, hypertension is one of the main causes of ESRD. Thus, early screening of hypertension can prevent kidney damage and reduce further problems in renal transplant recipients.

  11. Load forecasting

    International Nuclear Information System (INIS)

    Mak, H.

    1995-01-01

    Slides used in a presentation at The Power of Change Conference in Vancouver, BC in April 1995 about the changing needs for load forecasting were presented. Technological innovations and population increase were said to be the prime driving forces behind the changing needs in load forecasting. Structural changes, market place changes, electricity supply planning changes, and changes in planning objectives were other factors discussed. It was concluded that load forecasting was a form of information gathering, that provided important market intelligence

  12. HFE mRNA expression is responsive to intracellular and extracellular iron loading: short communication.

    Science.gov (United States)

    Mehta, Kosha J; Farnaud, Sebastien; Patel, Vinood B

    2017-10-01

    In liver hepatocytes, the HFE gene regulates cellular and systemic iron homeostasis by modulating cellular iron-uptake and producing the iron-hormone hepcidin in response to systemic iron elevation. However, the mechanism of iron-sensing in hepatocytes remain enigmatic. Therefore, to study the effect of iron on HFE and hepcidin (HAMP) expressions under distinct extracellular and intracellular iron-loading, we examined the effect of holotransferrin treatment (1, 2, 5 and 8 g/L for 6 h) on intracellular iron levels, and mRNA expressions of HFE and HAMP in wild-type HepG2 and previously characterized iron-loaded recombinant-TfR1 HepG2 cells. Gene expression was analyzed by real-time PCR and intracellular iron was measured by ferrozine assay. Data showed that in the wild-type cells, where intracellular iron content remained unchanged, HFE expression remained unaltered at low holotransferrin treatments but was upregulated upon 5 g/L (p HFE and HAMP expressions were elevated only at low 1 g/L treatment (p HFE (p HFE mRNA was independently elevated by extracellular and intracellular iron-excess. Thus, it may be involved in sensing both, extracellular and intracellular iron. Repression of HAMP expression under simultaneous intracellular and extracellular iron-loading resembles non-hereditary iron-excess pathologies.

  13. On a lunar space elevator

    Science.gov (United States)

    Lemke, E. H.

    We consider a space elevator system for lunar surface access that consists of a space station in circumlunar orbit, a cable reaching down to some meters above the surface and a magnetically levitated vehicle driven by a linear motor. It accelerates the load to be lifted to the speed of the cable end. Loads to be delivered are either put on the vehicle and slowed down by it or they are slowed down by a sand braking technique in a mare terrain. It is technically possible to operate this transport system nearly without fuel supply from Earth. We calculate various steel cable dimensions for a static stress maximum of 1/5th of the tensile strength. The process of takeover is considered in detail. Five ways of eliminating the adverse large cable elongation due to the load are described. The touchdown process and behaviour of the cable after disconnection are analysed. The positive difference between the speed of the load at takeover and cable end can excite a large inplane swing motion. We propose to damp it by a dissipative pulley that hangs in a loop of wire leading to the ends of two beams mounted on the space station tangentially to the orbit, the pulley's core being connected with the load. Roll librations are damped by energy losses in the elastic beams; damping can be reinforced by viscous beam elements and/or controlled out-of-plane motions of the beams. We argue in favour of the possibility of fast deployment. The problems of vehicle vibrations and agglutination at sand braking blades are underlined and their combined experimental investigation is suggested.

  14. The Human Remains from HMS Pandora

    Directory of Open Access Journals (Sweden)

    D.P. Steptoe

    2002-04-01

    Full Text Available In 1977 the wreck of HMS Pandora (the ship that was sent to re-capture the Bounty mutineers was discovered off the north coast of Queensland. Since 1983, the Queensland Museum Maritime Archaeology section has carried out systematic excavation of the wreck. During the years 1986 and 1995-1998, more than 200 human bone and bone fragments were recovered. Osteological investigation revealed that this material represented three males. Their ages were estimated at approximately 17 +/-2 years, 22 +/-3 years and 28 +/-4 years, with statures of 168 +/-4cm, 167 +/-4cm, and 166cm +/-3cm respectively. All three individuals were probably Caucasian, although precise determination of ethnicity was not possible. In addition to poor dental hygiene, signs of chronic diseases suggestive of rickets and syphilis were observed. Evidence of spina bifida was seen on one of the skeletons, as were other skeletal anomalies. Various taphonomic processes affecting the remains were also observed and described. Compact bone was observed under the scanning electron microscope and found to be structurally coherent. Profiles of the three skeletons were compared with historical information about the 35 men lost with the ship, but no precise identification could be made. The investigation did not reveal the cause of death. Further research, such as DNA analysis, is being carried out at the time of publication.

  15. SMART POINT CLOUD: DEFINITION AND REMAINING CHALLENGES

    Directory of Open Access Journals (Sweden)

    F. Poux

    2016-10-01

    Full Text Available Dealing with coloured point cloud acquired from terrestrial laser scanner, this paper identifies remaining challenges for a new data structure: the smart point cloud. This concept arises with the statement that massive and discretized spatial information from active remote sensing technology is often underused due to data mining limitations. The generalisation of point cloud data associated with the heterogeneity and temporality of such datasets is the main issue regarding structure, segmentation, classification, and interaction for an immediate understanding. We propose to use both point cloud properties and human knowledge through machine learning to rapidly extract pertinent information, using user-centered information (smart data rather than raw data. A review of feature detection, machine learning frameworks and database systems indexed both for mining queries and data visualisation is studied. Based on existing approaches, we propose a new 3-block flexible framework around device expertise, analytic expertise and domain base reflexion. This contribution serves as the first step for the realisation of a comprehensive smart point cloud data structure.

  16. What remains of the Arrow oil?

    International Nuclear Information System (INIS)

    Sergy, G.; Owens, E.

    1993-01-01

    In February 1970, the tanker Arrow became grounded 6.5 km off the north shore of Chedabucto Bay, Nova Scotia, and nearly 72,000 bbl of Bunker C fuel oil were released from the vessel during its subsequent breakup and sinking. The oil was washed ashore in various degrees over an estimated 305 km of the bay's 604-km shoreline, of which only 48 km were cleaned. In addition, the tanker Kurdistan broke in two in pack ice in March 1979 in the Cabot Strait area, spilling ca 54,000 bbl of Bunker C, some of which was later found at 16 locations along the northeast and east shorelines of Chedabucto Bay. In summer 1992, a systematic ground survey of the bay's shorelines was conducted using Environment Canada Shoreline Cleanup Assessment Team (SCAT) procedures. Standard observations were made of oil distribution and width, thickness, and character of the oil residues in 419 coastal segments. Results from the survey are summarized. Oil was found to be present on 13.3 km of the shoreline, with heavy oiling restricted to 1.3 km primarily in the areas of Black Duck Cove and Lennox Passage. Some of this residual oil was identified as coming from the Arrow. Natural weathering processes account for removal of most of the spilled oil from the bay. Oil remaining on the shore was found in areas outside of the zone of physical wave action, in areas of nearshore mixing where fine sediments are not present to weather the oil through biophysical processes, or in crusts formed by oil weathered on the surface. The systematic description of oiled shorelines using the SCAT methodology proved very successful, even for such an old spill. 6 refs

  17. Ghost Remains After Black Hole Eruption

    Science.gov (United States)

    2009-05-01

    NASA's Chandra X-ray Observatory has found a cosmic "ghost" lurking around a distant supermassive black hole. This is the first detection of such a high-energy apparition, and scientists think it is evidence of a huge eruption produced by the black hole. This discovery presents astronomers with a valuable opportunity to observe phenomena that occurred when the Universe was very young. The X-ray ghost, so-called because a diffuse X-ray source has remained after other radiation from the outburst has died away, is in the Chandra Deep Field-North, one of the deepest X-ray images ever taken. The source, a.k.a. HDF 130, is over 10 billion light years away and existed at a time 3 billion years after the Big Bang, when galaxies and black holes were forming at a high rate. "We'd seen this fuzzy object a few years ago, but didn't realize until now that we were seeing a ghost", said Andy Fabian of the Cambridge University in the United Kingdom. "It's not out there to haunt us, rather it's telling us something - in this case what was happening in this galaxy billions of year ago." Fabian and colleagues think the X-ray glow from HDF 130 is evidence for a powerful outburst from its central black hole in the form of jets of energetic particles traveling at almost the speed of light. When the eruption was ongoing, it produced prodigious amounts of radio and X-radiation, but after several million years, the radio signal faded from view as the electrons radiated away their energy. HDF 130 Chandra X-ray Image of HDF 130 However, less energetic electrons can still produce X-rays by interacting with the pervasive sea of photons remaining from the Big Bang - the cosmic background radiation. Collisions between these electrons and the background photons can impart enough energy to the photons to boost them into the X-ray energy band. This process produces an extended X-ray source that lasts for another 30 million years or so. "This ghost tells us about the black hole's eruption long after

  18. Unusual head and neck injury in elevator: autopsy study.

    Science.gov (United States)

    Eren, B; Türkmen, N; Dokgöz, H

    2012-10-01

    Industrial injuries related to auto-load-carrying vehicles were not frequently reported in the literature. Presented case was, 31-year-old male furniture worker. Deceased was found in awkward position in furniture workshop. Victim was observed on his knees in front of the elevator, head and neck lodged within openings of the elevator, and head and neck structures compressed-guillotined by the lower platform of the elevator were detected. We presented rare case of head and neck compression by elevator. Key words: head - neck - accidents - elevator - autopsy.

  19. De stille elever

    DEFF Research Database (Denmark)

    Winther-Lindqvist, Ditte Alexandra

    2012-01-01

    Det er blevet en afgørende samværskompetence i uddannelsessystemet at stå aktivt frem og deltage verbalt i skoleklassens liv både fagligt og socialt. Men ikke alle elever deltager lige villigt verbalt i plenum. Artiklen handler om de stille elever og konsekvenserne af stillehed i skolen. Det...... foreslås at skolesystemet sanktionerer ældre elever hårdere for stillehed end yngre elever og det forklares med at skolelivet også er en kultivering henimod elevhed som social identitet og denne er der forventning om at eleverne mestrer i udskolingen....

  20. The Ilizarov external fixator: what remains of the wire pretension after dynamic loading?

    NARCIS (Netherlands)

    Renard, A.J.S.; Schutte, B.G.; Verdonschot, N.J.J.; Kampen, A. van

    2005-01-01

    BACKGROUND: Maintenance of wire pretension in an Ilizarov external fixator is dependent on the torque applied to the fixation bolts. We therefore measured immediately after surgery the clinically applied torques. The median value was only 10 N m (range 8-14N m). We wondered whether this value is

  1. 29 CFR 1918.87 - Ship's cargo elevators.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Ship's cargo elevators. 1918.87 Section 1918.87 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR LONGSHORING Handling Cargo § 1918.87 Ship's cargo elevators. (a) Safe working load. The safe workin...

  2. The Supraspinatus and the Deltoid - Not just two arm elevators

    NARCIS (Netherlands)

    de Witte, P.; Werner, S.; ter Braak, L.M.; Veeger, H.E.J.; Nelissen, R.G.H.H.; de Groot, J.H.

    2014-01-01

    Background: The debate on the clinical and functional role of the Supraspinatus in relation to the Deltoid necessitates experimental assessment of their contributions to arm elevation. Our goal was to evaluate the responses of both muscles to increased elevation moment loading. Methods: Twenty-three

  3. Genetically elevated bilirubin and risk of ischaemic heart disease

    DEFF Research Database (Denmark)

    Stender, Stefan; Frikke-Schmidt, R; Nordestgaard, B G

    2013-01-01

    Elevated plasma levels of bilirubin, an endogenous antioxidant, have been associated with reduced risk of ischaemic heart disease (IHD) and myocardial infarction (MI). Whether this is a causal relationship remains unclear.......Elevated plasma levels of bilirubin, an endogenous antioxidant, have been associated with reduced risk of ischaemic heart disease (IHD) and myocardial infarction (MI). Whether this is a causal relationship remains unclear....

  4. Undervisning af tosprogede elever

    DEFF Research Database (Denmark)

    Horst, Christian

    2003-01-01

    Artiklen fremdrager hovedresultaterne fra Virginia P. Collier's og Wayne P. Thomas's længdeundersøgelser af tosprogede elever i USA, som formentlig er de mest omfattende undersøgelser af undervisningen af tosprogede elever overhovedet. Resultaterne diskuteres i relation til udviklingen af en...

  5. Effects of elevated CO

    NARCIS (Netherlands)

    Xue, Sha; Yang, Xiaomei; Liu, Guobin; Gai, Lingtong; Zhang, Changsheng; Ritsema, Coen J.; Geissen, Violette

    2017-01-01

    Elevated CO2 and drought are key consequences of climate change and affect soil processes and plant growth. This study investigated the effects of elevated CO2 and drought on the microbial biomass and enzymatic activities in the rhizospheres of Bothriochloa ischaemum and

  6. Bucket elevator type continuous unloader; Basket elevator gata renzokushiki anroda

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-20

    This unloader was delivered to Wakayama branch of Sumikin Butsuryu in the site of Wakayama steel plant of Sumitomo Metal Industries Ltd. for landing sub-materials for ironworks. Main specifications: (1) Capacity: 400t/h for limestone, 280t/h for gypsum, (2) Kinds of ships: 5,000DWT maximum, (3) Boom swing radius: 20m. Features: (1) Simple light-weight unloader for not large ships for main materials but small coastal service ships which works with not swing motion but only traveling and normal-directional motion of the under structure of a bucket elevator unit, (2) Various useful functions such as ground conveyance, truck loading, back yard stacking and back yard shipment for handling of various sub-materials. (translated by NEDO)

  7. Beam loading

    OpenAIRE

    Boussard, Daniel

    1987-01-01

    We begin by giving a description of the radio-frequency generator-cavity-beam coupled system in terms of basic quantities. Taking beam loading and cavity detuning into account, expressions for the cavity impedance as seen by the generator and as seen by the beam are derived. Subsequently methods of beam-loading compensation by cavity detuning, radio-frequency feedback and feedforward are described. Examples of digital radio-frequency phase and amplitude control for the special case of superco...

  8. Respiratory Changes in Response to Cognitive Load: A Systematic Review.

    Science.gov (United States)

    Grassmann, Mariel; Vlemincx, Elke; von Leupoldt, Andreas; Mittelstädt, Justin M; Van den Bergh, Omer

    2016-01-01

    When people focus attention or carry out a demanding task, their breathing changes. But which parameters of respiration vary exactly and can respiration reliably be used as an index of cognitive load? These questions are addressed in the present systematic review of empirical studies investigating respiratory behavior in response to cognitive load. Most reviewed studies were restricted to time and volume parameters while less established, yet meaningful parameters such as respiratory variability have rarely been investigated. The available results show that respiratory behavior generally reflects cognitive processing and that distinct parameters differ in sensitivity: While mentally demanding episodes are clearly marked by faster breathing and higher minute ventilation, respiratory amplitude appears to remain rather stable. The present findings further indicate that total variability in respiratory rate is not systematically affected by cognitive load whereas the correlated fraction decreases. In addition, we found that cognitive load may lead to overbreathing as indicated by decreased end-tidal CO2 but is also accompanied by elevated oxygen consumption and CO2 release. However, additional research is needed to validate the findings on respiratory variability and gas exchange measures. We conclude by outlining recommendations for future research to increase the current understanding of respiration under cognitive load.

  9. Elevators or stairs?

    Science.gov (United States)

    Shah, Sachin; O’Byrne, Michael; Wilson, Merne; Wilson, Thomas

    2011-01-01

    Background: Staff in hospitals frequently travel between floors and choose between taking the stairs or elevator. We compared the time savings with these two options. Methods: Four people aged 26–67 years completed 14 trips ranging from one to six floors, both ascending and descending. We compared the amount of time per floor travelled by stairs and by two banks of elevators. Participants reported their fatigue levels using a modified Borg scale. We performed two-way analysis of variance to compare the log-transformed data, with participant and time of day as independent variables. Results: The mean time taken to travel between each floor was 13.1 (standard deviation [SD] 1.7) seconds by stairs and 37.5 (SD 19.0) and 35.6 (SD 23.1) seconds by the two elevators (F = 8.61, p elevator equaled about 15 minutes a day. Self-reported fatigue was less than 13 (out of 20) on the Borg scale for all participants, and they all stated that they were able to continue their duties without resting. The extra time associated with elevator use was because of waiting for its arrival. There was a difference in the amount of time taken to travel by elevator depending on the time of day and day of the week. Interpretation: Taking the stairs rather than the elevator saved about 15 minutes each workday. This 3% savings per workday could translate into improved productivity as well as increased fitness. PMID:22159365

  10. Effect of Interbody Fusion on the Remaining Discs of the Lumbar Spine in Subjects with Disc Degeneration.

    Science.gov (United States)

    Ryu, Robert; Techy, Fernando; Varadarajan, Ravikumar; Amirouche, Farid

    2016-02-01

    To study effects (stress loads) of lumbar fusion on the remaining segments (adjacent or not) of the lumbar spine in the setting of degenerated adjacent discs. A lumbar spine finite element model was built and validated. The full model of the lumbar spine was a parametric finite element model of segments L 1-5 . Numerous hypothetical combinations of one-level lumbar spine fusion and one-level disc degeneration were created. These models were subjected to 10 Nm flexion and extension moments and the stresses on the endplates and consequently on the intervertebral lumbar discs measured. These values were compared to the stresses on healthy lumbar spine discs under the same load and fusion scenarios. Increased stress at endplates was observed only in the settings of L4-5 fusion and L3-4 disc degeneration (8% stress elevation at L2,3 in flexion or extension, and 25% elevation at L3,4 in flexion only). All other combinations showed less endplate stress than did the control model. For fusion at L3-4 and degeneration at L4-5 , the stresses in the endplates at the adjacent level inferior to the fused disc decreased for both loading disc height reductions. Stresses in flexion decreased after fusion by 29.5% and 25.8% for degeneration I and II, respectively. Results for extension were similar. For fusion at L2-3 and degeneration at L4-5 , stresses in the endplates decreased more markedly at the degenerated (30%), than at the fused level (14%) in the presence of 25% disc height reduction and 10 Nm flexion, whereas in extension stresses decreased more at the fused (24.3%) than the degenerated level (5.86%). For fusion at L3-4 and degeneration at L2-3 , there were no increases in endplate stress in any scenario. For fusion at L4-5 and degeneration at L3-4 , progression of degeneration from I to II had a significant effect only in flexion. A dramatic increase in stress was noted in the endplates of the degenerated disc (L3-4 ) in flexion for degeneration II. Stresses are greater

  11. Science on a space elevator

    Energy Technology Data Exchange (ETDEWEB)

    Laubscher, B. E. (Bryan E.); Jorgensen, A. M. (Anders M.)

    2004-01-01

    The Space Elevator (SE) represents a major paradigm shift in space access. If the SE's promise of low cost access can be realized, everything becomes economically more feasible to accomplish in space. In this paper we describe in-situ science stations mounted on a science-dedicated space elevator tether. The concept presented here involves a carbon nanotube ribbon that is constructed by an existing space elevator and then science sensors are stationed along the ribbon at differing altitudes. The finished ribbon can be moved across the earth to the position at which its scientific measurements are to be taken. The ability to station scientific, in-situ instrumentation at different altitudes for round-the-clock observations is a unique capability of the SE. The environments that the science packages sense range from the troposphere out beyond the magnetopause of the magnetosphere on the solar side of the earth. Therefore, the very end of the SE can sense the solar wind. The measurements at various points along its length include temperature, pressure, density, sampling, chemical analyses, wind speed, turbulence, free oxygen, electromagnetic radiation, cosmic rays, energetic particles and plasmas in the earth's magnetosphere and the solar wind. There exist some altitudes that are difficult to access with aircraft or balloons or rockets and so remain relatively unexplored. The space elevator solves these problems and opens these regions up to in-situ measurements. Without the need for propulsion, the SE provides a more benign and pristine environment for atmospheric measurements than available with powered aircraft. Moreover, replacing and upgrading instrumentation is expected to be very cost effective with the SE. Moving and stationing the science SE affords the opportunity to sense multiple regions of the atmosphere. The SE's geosynchronous, orbital motion through the magnetosphere, albeit nominally with Earth's magnetic field, will trace a plane

  12. Indsatser for tosprogede elever

    DEFF Research Database (Denmark)

    Andersen, Dines; Jakobsen, Vibeke; Jensen, Vibeke Myrup

    Fagligt set klarer tosprogede elever sig dårligere i skolen og det videre uddannelsessystem end ’danske’ elever. Kommuner og folkeskoler har derfor sat en række tiltag i værk, som sigter mod at forbedre de tosprogede elevers skole- og uddannelsessituation. Rapporten kortlægger og analyserer...... af klasseundervisningen. Analysen viser, at de elever, der bliver taget ud af klassen for at få ekstra undervisning i dansk som andetsprog, klarer sig dårligere end elever, der modtager ekstraundervisningen i klassen eller uden for skoletid. Undersøgelsen er baseret på spørgeskemaundersøgelser blandt...... kommunale forvaltningschefer, skoleledere, lærere og forældre til børn i 2. klasse samt lærere til og elever i 9. klasse, SFI’s forløbsundersøgelse af årgang 1995 og registerdata. Undersøgelsen er via Ministeriet for Børn og Undervisning betalt med midler fra satspuljeaftalen 2009 om integration....

  13. Behavior of reinforced concrete at elevated temperatures

    International Nuclear Information System (INIS)

    Freskakis, G.N.

    1984-09-01

    A study is presented concerning the behavior of reinforced concrete sections at elevated temperatures. Material properties of concrete and reinforcing steel are discussed. Behavior studies are made by means of moment-curvature-axial force relationships. Particular attention is given to the load carrying capacity, thermal forces and moments, and deformation capacity. The effects on these properties of variations in the strength properties, the temperature level and distribution, the amount of reinforcing steel, and limiting values of strains are considered

  14. Beam loading

    CERN Document Server

    Gamp, Alexander

    2013-01-01

    We begin by giving a description of the radio-frequency generator-cavity-beam coupled system in terms of basic quantities. Taking beam loading and cavity detuning into account, expressions for the cavity impedance as seen by the generator and as seen by the beam are derived. Subsequently methods of beam-loading compensation by cavity detuning, radio-frequency feedback and feedforward are described. Examples of digital radio-frequency phase and amplitude control for the special case of superconducting cavities are also given. Finally, a dedicated phase loop for damping synchrotron oscillations is discussed.

  15. Beam loading

    International Nuclear Information System (INIS)

    Gamp, Alexander

    2013-01-01

    We begin by giving a description of the radio-frequency generator-cavity-beam coupled system in terms of basic quantities. Taking beam loading and cavity detuning into account, expressions for the cavity impedance as seen by the generator and as seen by the beam are derived. Subsequently methods of beam-loading compensation by cavity detuning, radio-frequency feedback and feedforward are described. Examples of digital radio-frequency phase and amplitude control for the special case of superconducting cavities are also given. Finally, a dedicated phase loop for damping synchrotron oscillations is discussed. (author)

  16. Load sensor

    NARCIS (Netherlands)

    Van den Ende, D.; Almeida, P.M.R.; Dingemans, T.J.; Van der Zwaag, S.

    2007-01-01

    The invention relates to a load sensor comprising a polymer matrix and a piezo-ceramic material such as PZT, em not bedded in the polymer matrix, which together form a compos not ite, wherein the polymer matrix is a liquid crystalline resin, and wherein the piezo-ceramic material is a PZT powder

  17. Carbohydrate Loading.

    Science.gov (United States)

    Csernus, Marilyn

    Carbohydrate loading is a frequently used technique to improve performance by altering an athlete's diet. The objective is to increase glycogen stored in muscles for use in prolonged strenuous exercise. For two to three days, the athlete consumes a diet that is low in carbohydrates and high in fat and protein while continuing to exercise and…

  18. Evaluation of remaining life of the double-shell tank waste systems

    International Nuclear Information System (INIS)

    Schwenk, E.B.

    1995-01-01

    A remaining life assessment of the DSTs (double-shell tanks) and their associated waste transfer lines, for continued operation over the next 10 years, was favorable. The DST assessment was based on definition of significant loads, evaluation of data for possible material degradation and geometric changes and evaluation of structural analyses. The piping assessment was based primarily on service experience

  19. Evaluation of remaining life of the double-shell tank waste systems

    Energy Technology Data Exchange (ETDEWEB)

    Schwenk, E.B.

    1995-05-04

    A remaining life assessment of the DSTs (double-shell tanks) and their associated waste transfer lines, for continued operation over the next 10 years, was favorable. The DST assessment was based on definition of significant loads, evaluation of data for possible material degradation and geometric changes and evaluation of structural analyses. The piping assessment was based primarily on service experience.

  20. National Elevation Dataset

    Science.gov (United States)

    ,

    2002-01-01

    The National Elevation Dataset (NED) is a new raster product assembled by the U.S. Geological Survey. NED is designed to provide National elevation data in a seamless form with a consistent datum, elevation unit, and projection. Data corrections were made in the NED assembly process to minimize artifacts, perform edge matching, and fill sliver areas of missing data. NED has a resolution of one arc-second (approximately 30 meters) for the conterminous United States, Hawaii, Puerto Rico and the island territories and a resolution of two arc-seconds for Alaska. NED data sources have a variety of elevation units, horizontal datums, and map projections. In the NED assembly process the elevation values are converted to decimal meters as a consistent unit of measure, NAD83 is consistently used as horizontal datum, and all the data are recast in a geographic projection. Older DEM's produced by methods that are now obsolete have been filtered during the NED assembly process to minimize artifacts that are commonly found in data produced by these methods. Artifact removal greatly improves the quality of the slope, shaded-relief, and synthetic drainage information that can be derived from the elevation data. Figure 2 illustrates the results of this artifact removal filtering. NED processing also includes steps to adjust values where adjacent DEM's do not match well, and to fill sliver areas of missing data between DEM's. These processing steps ensure that NED has no void areas and artificial discontinuities have been minimized. The artifact removal filtering process does not eliminate all of the artifacts. In areas where the only available DEM is produced by older methods, then "striping" may still occur.

  1. High speed elevator s rise high rise building; Chokoso biru wo kakenoboru elevator

    Energy Technology Data Exchange (ETDEWEB)

    Tanabe, K. [Mitsubishi Electric Corp., Tokyo (Japan)

    1994-10-20

    The world`s fastest (750 m/min) elevators are operating in Yokohama Landmark Tower. This paper describes how engineers solved the technological problems to realize the high-speed elevator. Buildings in Japan have become higher and higher. At the present, this Tower is the highest in Japan (296 m, 70 stories). The Ministry of Construction is going to start a research team to study construction of buildings of the order of 1,000 m high. An important issue for a skyscraper is how to reduce the elevator space adapting to the increase of the number of inhabitants in the building. The basic solution is to increase the elevator speed and to plan the best elevator moving line. The 120 kW AC motor direct-driven winding machine that withstands the superhigh-speed suspending load was developed. Vibrations from the motor and the mechanical system are minimized and the touch-down tolerances for the elevator cage are controlled to {plus_minus}15 mm. The safety devices of the elevator include the emergency stopper of special ceramic material and the hydraulic shock absorber with the optimum reduction characteristic. 2 refs., 3 figs.

  2. Load sensor

    OpenAIRE

    Van den Ende, D.; Almeida, P.M.R.; Dingemans, T.J.; Van der Zwaag, S.

    2007-01-01

    The invention relates to a load sensor comprising a polymer matrix and a piezo-ceramic material such as PZT, em not bedded in the polymer matrix, which together form a compos not ite, wherein the polymer matrix is a liquid crystalline resin, and wherein the piezo-ceramic material is a PZT powder forming 30-60% by volume of the composite, and wherein the PZT powder forms 40-50% by volume of the composite.

  3. Multisensory Cues Capture Spatial Attention Regardless of Perceptual Load

    Science.gov (United States)

    Santangelo, Valerio; Spence, Charles

    2007-01-01

    We compared the ability of auditory, visual, and audiovisual (bimodal) exogenous cues to capture visuo-spatial attention under conditions of no load versus high perceptual load. Participants had to discriminate the elevation (up vs. down) of visual targets preceded by either unimodal or bimodal cues under conditions of high perceptual load (in…

  4. Interaktive tavler - interaktive elever

    DEFF Research Database (Denmark)

    Reusch, Charlotte F.; Otzen, Elsebeth

    Abstract, Poster-præsentation 13.-14. juni 2012, Pilotprojekt: Interaktive tavler – interaktive elever Lektor, cand. pæd., Elsebeth Otzen og Lektor, cand. mag., Charlotte Reusch, Institut for Skole og Læring, Læreruddannelsen, Professionshøjskolen Metropol, København Hvordan motiverer en interaktiv...... tavle lærere og elever? Hvad sker der mellem elev, stof og lærer, når læreren bliver i stand til at billedliggøre og dynamisere sine oplæg på tavlen? Bliver læreroplæg prioriteret? Bliver eleverne aktive, eller ender den interaktive tavle med blot at understøtte lærerens envejskommunikation til klassen......? Og hvad sker der mellem eleverne? Disse spørgsmål var igangsættende for arbejdet med pilotprojektet Interaktive tavler – interaktive elever, som blev afviklet i skoleåret 2010-2011. Projektet blev udført af en tværfaglig gruppe, bestående af lektorer i matematik, biologi og dansk i læreruddannelsen...

  5. Udeskole og elevers handlekompetence

    DEFF Research Database (Denmark)

    Breiting, Søren

    2011-01-01

    Elever elsker at komme væk fra undervisningen i skolen. Er det positivt eller negativt? Og hvad har betydning for, at eleverne får mest muligt ud af oplevelserne uden for skolen? Forskellige former for udeskole giver nogle oplagte muligheder, så eleverne udvikler sig som engagerede borgere i et...

  6. Interaktive tavler - interaktive elever

    DEFF Research Database (Denmark)

    Reusch, Charlotte; Otzen, Elsebeth

    Abstract, Poster-præsentation 13.-14. juni 2012, Pilotprojekt: Interaktive tavler ? interaktive elever Lektor, cand. pæd., Elsebeth Otzen og Lektor, cand. mag., Charlotte Reusch, Institut for Skole og Læring, Læreruddannelsen, Professionshøjskolen Metropol, København Hvordan motiverer en interaktiv...... tavle lærere og elever? Hvad sker der mellem elev, stof og lærer, når læreren bliver i stand til at billedliggøre og dynamisere sine oplæg på tavlen? Bliver læreroplæg prioriteret? Bliver eleverne aktive, eller ender den interaktive tavle med blot at understøtte lærerens envejskommunikation til klassen......? Og hvad sker der mellem eleverne? Disse spørgsmål var igangsættende for arbejdet med pilotprojektet Interaktive tavler ? interaktive elever, som blev afviklet i skoleåret 2010-2011. Projektet blev udført af en tværfaglig gruppe, bestående af lektorer i matematik, biologi og dansk i læreruddannelsen...

  7. Elevator frames two columns

    OpenAIRE

    Marín Jiménez, Juan Francisco

    2015-01-01

    This project aims to solve the problem of vertical transport of charges raised by a company with the standard UNE 58-132-91/6. The purpose of this project is the industrial design of a system of load handling by a bi-columned lifting device, tractioned by flat belts and steel cables from a transport level to a different level in order to connect two different assembly lines situated at different heights. The goal of this project is lifting a 780 Kg load at a 2.400 mm height....

  8. Experimental prototype of an electric elevator

    Science.gov (United States)

    Gaiceanu, M.; Epure, S.; Ciuta, S.

    2016-08-01

    The main objective is to achieve an elevator prototype powered by a three-phase voltage system via a bidirectional static power converter ac-ac with regenerating capability. In order to diminish the power size of the electric motor up to 1/3 of rated power, the elevator contains two carriages of the same weight, one serving as the payload, and the other as counterweight. Before proper operation of the static power converter, the capacitor must be charged at rated voltage via a precharge circuit. At the moment of stabilizing the DC voltage at nominal value, the AC-AC power converter can operates in the proper limits. The functions of the control structure are: the load control task, speed and torque controls. System includes transducers for current measuring, voltage sensors and encoder. As reserve power sources the hybrid battery-photovoltaic panels are used. The control voltage is modulated by implementing four types of pulse width modulations: sinusoidal, with reduced commutation, third order harmonic insertion, and the space vector modulation. Therefore, the prototype could operates with an increased efficiency, in spite of the existing ones. The experimental results confirm the well design of the chosen solution. The control solution assures bidirectional power flow control, precharge control, and load control and it is implemented on a digital signal processor. The elevator capacity is between 300-450 kg, and it is driven by using a 1.5 kW three-phase asynchronous machine.

  9. Skuldertesten "Kombineret Elevation"

    DEFF Research Database (Denmark)

    Clausen, Mikkel Bek; Overkær, Brian

    2010-01-01

    Formål: At udarbejde en testprotokol for testen Kombineret Elevation (KE) og undersøge test-retest variationen ved test af elite svømmere, samt diskutere testens relevans og validitet. Materiale og Metode: 9 elite og 10 sub-elite svømmere, heraf var 11 mænd og 8 kvinder, gennemførte testen KE 2...

  10. Fish elevator and method of elevating fish

    Energy Technology Data Exchange (ETDEWEB)

    Truebe, J.; Drooker, M.S.

    1984-02-14

    A means and method are disclosed for transporting fish from a lower body of water to a higher body of water. The means comprise a tubular lock with a gated entrance below the level of the lower body of water through which fish may enter the lock and a discharge passage above the level of the upper body of water. The fish raising means in the lock is a crowder pulled upward by a surface float as water from the upper body of water gravitationally flows into the closed lock filling it to the level of the upper body. Water is then pumped into the lock to raise the level to the discharge passage. The crowder is then caused to float upward the remaining distance through the water to the level of the discharge passage by the introduction of air into a pocket on the underside of the crowder. The fish are then automatically discharged from the lock into the discharge passage by the out of water position of the crowder. The movement of the fish into the discharge passage is aided by the continuous overflow of water still being pumped into the lock. A pipe may be connected to the discharge passage to deliver the fish to a selected location in the upper body of water. 6 figs.

  11. Fish elevator and method of elevating fish

    Science.gov (United States)

    Truebe, Jonathan; Drooker, Michael S.

    1984-01-01

    A means and method for transporting fish from a lower body of water to a higher body of water. The means comprises a tubular lock with a gated entrance below the level of the lower body of water through which fish may enter the lock and a discharge passage above the level of the upper body of water. The fish raising means in the lock is a crowder pulled upward by a surface float as water from the upper body of water gravitationally flows into the closed lock filling it to the level of the upper body. Water is then pumped into the lock to raise the level to the discharge passage. The crowder is then caused to float upward the remaining distance through the water to the level of the discharge passage by the introduction of air into a pocket on the underside of the crowder. The fish are then automatically discharged from the lock into the discharge passage by the out of water position of the crowder. The movement of the fish into the discharge passage is aided by the continuous overflow of water still being pumped into the lock. A pipe may be connected to the discharge passage to deliver the fish to a selected location in the upper body of water.

  12. High thermal load receiving heat plate

    International Nuclear Information System (INIS)

    Shibutani, Jun-ichi; Shibayama, Kazuhito; Yamamoto, Keiichi; Uchida, Takaho.

    1993-01-01

    The present invention concerns a high thermal load heat receiving plate such as a divertor plate of a thermonuclear device. The high thermal load heat receiving plate of the present invention has a cooling performance capable of suppressing the temperature of an armour tile to less than a threshold value of the material against high thermal loads applied from plasmas. Spiral polygonal pipes are inserted in cooling pipes at a portion receiving high thermal loads in the high temperature load heat receiving plate of the present invention. Both ends of the polygonal pipes are sealed by lids. An area of the flow channel in the cooling pipes is thus reduced. Heat conductivity on the cooling surface of the cooling pipes is increased in the high thermal load heat receiving plate having such a structure. Accordingly, temperature elevation of the armour tile can be suppressed. (I.S.)

  13. A spider elevator

    Energy Technology Data Exchange (ETDEWEB)

    Butylkin, A.V.; Butylkin, V.A.; Izosimov, A.M.

    1983-01-01

    A spider elevator is proposed which contains a body, a wedge clamp with wedges hinged to each other, a subassembly for holding the wedge clamp in the open and closed positions and a mechanism for changing the wedge clamp, which is made in the form of levers with ears for cleats and installed in the body with the capability of turning. To increase reliability in the operational mode through using the external force for clamping the pipe, the free ends of the levers are hinged with the body by a power cylinder.

  14. Elevator Control Strategies

    OpenAIRE

    Ceder, Frederick; Nordin, Alexandra

    2013-01-01

    The purpose of this essay is to investigate if it is eective to switch strategies for elevators during one day in an oce building. This essay describes some of the strategies in use today, followed by a comparison and analysis of two of the strategies described. We have also implemented optimizations to one of these strategies. From our test results we can conclude that our optimized strategy worked and produced better results on average waiting time and total traveling time than the two stra...

  15. Remaining lifetime modeling using State-of-Health estimation

    Science.gov (United States)

    Beganovic, Nejra; Söffker, Dirk

    2017-08-01

    has lower degrees of freedom. Both approaches rely on previously developed lifetime models each of them corresponding to predefined SoH. Concerning first approach, model selection is aided by state-machine-based algorithm. In the second approach, model selection conditioned by tracking an exceedance of predefined thresholds is concerned. The approach is applied to data generated from tribological systems. By calculating Root Squared Error (RSE), Mean Squared Error (MSE), and Absolute Error (ABE) the accuracy of proposed models/approaches is discussed along with related advantages and disadvantages. Verification of the approach is done using cross-fold validation, exchanging training and test data. It can be stated that the newly introduced approach based on data (denoted as data-based or data-driven) parametric models can be easily established providing detailed information about remaining useful/consumed lifetime valid for systems with constant load but stochastically occurred damage.

  16. Load testing circuit

    DEFF Research Database (Denmark)

    2009-01-01

    A load testing circuit a circuit tests the load impedance of a load connected to an amplifier. The load impedance includes a first terminal and a second terminal, the load testing circuit comprising a signal generator providing a test signal of a defined bandwidth to the first terminal of the load...

  17. Automatic pipe elevator

    Energy Technology Data Exchange (ETDEWEB)

    Haney, K.M.; Willis, C.A.

    1987-03-17

    This patent describes an elevator adapted for use with a power swivel for supporting a drilling or production tubular, the elevator comprising: at least two jaws, each jaw having a clamping surface; a connector member for supporting the jaws, the connector member comprising an upper end, a lower end, means for coupling the upper end to the power swivel, means for coupling the lower end to a tubular. The member also comprises means for defining a passageway extending from the upper end to the lower end through the connector member to allow drilling mud to be passed from the power swivel through the bore, into the tubular; and linkage means mounted between the connector member and the jaws for coupling the jaws to the connector member and for maintaining the clamping surfaces of the jaws in clamping engagement with the tubular when the connector member and the tubular are urged apart relative to one another. The linkage means is configured such that the force by which the clamping surfaces clamp the tubular increases as the force urging the connector member and the tubular apart increases.

  18. Elevation data for floodplain mapping

    National Research Council Canada - National Science Library

    Committee on Floodplain Mapping Technologies; National Research Council; Division on Earth and Life Studies; National Research Council

    2007-01-01

    .... Elevation Data for Floodplain Mapping shows that there is sufficient two-dimensional base map imagery to meet FEMA's flood map modernization goals, but that the three-dimensional base elevation data...

  19. Clutch size declines with elevation in tropical birds

    Science.gov (United States)

    Boyce, A.J.; Freeman, Benjamin G.; Mitchell, Adam E.; Martin, Thomas E.

    2015-01-01

    Clutch size commonly decreases with increasing elevation among temperate-zone and subtropical songbird species. Tropical songbirds typically lay small clutches, thus the ability to evolve even smaller clutch sizes at higher elevations is unclear and untested. We conducted a comparative phylogenetic analysis using data gathered from the literature to test whether clutch size varied with elevation among forest passerines from three tropical biogeographic regions—the Venezuelan Andes and adjacent lowlands, Malaysian Borneo, and New Guinea. We found a significant negative effect of elevation on variation in clutch size among species. We found the same pattern using field data sampled across elevational gradients in Venezuela and Malaysian Borneo. Field data were not available for New Guinea. Both sets of results demonstrate that tropical montane species across disparate biogeographic realms lay smaller clutches than closely related low-elevation species. The environmental sources of selection underlying this pattern remain uncertain and merit further investigation.

  20. Loads and loads and loads: The influence of prospective load, retrospective load, and ongoing task load in prospective memory

    Directory of Open Access Journals (Sweden)

    Beat eMeier

    2015-06-01

    Full Text Available In prospective memory tasks different kinds of load can occur. Adding a prospective memory task can impose a load on ongoing task performance. Adding ongoing task load can affect prospective memory performance. The existence of multiple target events increases prospective load and adding complexity to the to-be-remembered action increases retrospective load. In two experiments, we systematically examined the effects of these different types of load on prospective memory performance. Results showed an effect of prospective load on costs in the ongoing task for categorical targets (Experiment 2, but not for specific targets (Experiment 1. Retrospective load and ongoing task load both affected remembering the retrospective component of the prospective memory task. We suggest that prospective load can enhance costs in the ongoing task due to additional monitoring requirements. Retrospective load and ongoing task load seem to impact the division of resources between the ongoing task and retrieval of the retrospective component, which may affect disengagement from the ongoing task. In general, the results demonstrate that the different types of load affect prospective memory differentially.

  1. An elevator wheel

    Energy Technology Data Exchange (ETDEWEB)

    Zhornik, V.I.; Cherkov, Ye.M.; Simonov, A.A.

    1982-01-01

    This invention deals with mineral enrichment and is primarily for unloading submerged products of enrichment during separation in heavy mediums. An elevator wheel is proposed for unloading the submerged product from the bath of a heavy to medium separator which includes ladle disks with internal walls and overlapping sheets hinged to the ends. In order to increase the degree of dehydration of the unloaded product, the internal wall of each ladle is made of sheets installed in stages with clearances relative to each other. The advantages of the proposed device include an improvement in the degree of dehydration of the submerged product in the ladles and a reduction in the carry away of the heavy medium with the enrichment products.

  2. Why does fertility remain high among certain UK-born ethnic minority women?

    Directory of Open Access Journals (Sweden)

    Hill Kulu

    2016-12-01

    Full Text Available Background: Previous research has shown high total fertility among certain UK-born ethnic minorities, but the reasons behind their high fertility have remained far from clear. Some researchers attribute their elevated fertility levels to cultural factors, whereas others argue that high fertility is the consequence of their poor education and labour market prospects. Objective: This study investigates fertility among the descendants of immigrants in the UK and examines the determinants of high fertility among certain ethnic minority groups. Methods: We use data from the Understanding Society study and apply multivariate event history analysis. Results: The analysis shows, first, that relatively high second-, third-, and fourth-birth rates are responsible for the elevated total fertility among certain UK-born minorities, especially women of Pakistani and Bangladeshi origin. There is little variation in the first-birth rates among natives and immigrant descendants. Second, although fertility differences between ethnic minorities and native British women slightly decrease once religiosity and number of siblings are controlled for, significant differences persist. We conclude that cultural factors account for some elevated fertility among ethnic groups in the UK, whereas the role of education and employment seem to be only minor. Contribution: Cultural factors account for some elevated fertility among ethnic minorities in the UK, whereas the role of education and employment seem to be negligible.

  3. Load carriage, human performance, and employment standards.

    Science.gov (United States)

    Taylor, Nigel A S; Peoples, Gregory E; Petersen, Stewart R

    2016-06-01

    The focus of this review is on the physiological considerations necessary for developing employment standards within occupations that have a heavy reliance on load carriage. Employees within military, fire fighting, law enforcement, and search and rescue occupations regularly work with heavy loads. For example, soldiers often carry loads >50 kg, whilst structural firefighters wear 20-25 kg of protective clothing and equipment, in addition to carrying external loads. It has long been known that heavy loads modify gait, mobility, metabolic rate, and efficiency, while concurrently elevating the risk of muscle fatigue and injury. In addition, load carriage often occurs within environmentally stressful conditions, with protective ensembles adding to the thermal burden of the workplace. Indeed, physiological strain relates not just to the mass and dimensions of carried objects, but to how those loads are positioned on and around the body. Yet heavy loads must be borne by men and women of varying body size, and with the expectation that operational capability will not be impinged. This presents a recruitment conundrum. How do employers identify capable and injury-resistant individuals while simultaneously avoiding discriminatory selection practices? In this communication, the relevant metabolic, cardiopulmonary, and thermoregulatory consequences of loaded work are reviewed, along with concomitant impediments to physical endurance and mobility. Also emphasised is the importance of including occupation-specific clothing, protective equipment, and loads during work-performance testing. Finally, recommendations are presented for how to address these issues when evaluating readiness for duty.

  4. Modelling and Simulation of Wave Loads

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Thoft-Christensen, Palle

    velocity can be approximated by a Gaussian Markov process. Known approximate results for the first-passage density or equivalently, the distribution of the extremes of wave loads are presented and compared with rather precise simulation results. It is demonstrated that the approximate results......A simple model of the wave load on slender members of offshore structures is described. The wave elevation of the sea state is modelled by a stationary Gaussian process. A new procedure to simulate realizations of the wave loads is developed. The simulation method assumes that the wave particle...

  5. Modelling and Simulation of Wave Loads

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Thoft-Christensen, Palle

    1985-01-01

    velocity can be approximated by a Gaussian Markov process. Known approximate results for the first passage density or equivalently, the distribution of the extremes of wave loads are presented and compared with rather precise simulation results. It is demonstrated that the approximate results......A simple model of the wave load on stender members of offshore structures is described . The wave elevation of the sea stateis modelled by a stationary Gaussian process. A new procedure to simulate realizations of the wave loads is developed. The simulation method assumes that the wave particle...

  6. Elevated CO2 stimulates marsh elevation gain, counterbalancing sea-level rise.

    Science.gov (United States)

    Langley, J Adam; McKee, Karen L; Cahoon, Donald R; Cherry, Julia A; Megonigal, J Patrick

    2009-04-14

    Tidal wetlands experiencing increased rates of sea-level rise (SLR) must increase rates of soil elevation gain to avoid permanent conversion to open water. The maximal rate of SLR that these ecosystems can tolerate depends partly on mineral sediment deposition, but the accumulation of organic matter is equally important for many wetlands. Plant productivity drives organic matter dynamics and is sensitive to global change factors, such as rising atmospheric CO(2) concentration. It remains unknown how global change will influence organic mechanisms that determine future tidal wetland viability. Here, we present experimental evidence that plant response to elevated atmospheric [CO(2)] stimulates biogenic mechanisms of elevation gain in a brackish marsh. Elevated CO(2) (ambient + 340 ppm) accelerated soil elevation gain by 3.9 mm yr(-1) in this 2-year field study, an effect mediated by stimulation of below-ground plant productivity. Further, a companion greenhouse experiment revealed that the CO(2) effect was enhanced under salinity and flooding conditions likely to accompany future SLR. Our results indicate that by stimulating biogenic contributions to marsh elevation, increases in the greenhouse gas, CO(2), may paradoxically aid some coastal wetlands in counterbalancing rising seas.

  7. Elevated CO2 stimulates marsh elevation gain, counterbalancing sea-level rise

    Science.gov (United States)

    Langley, J. Adam; McKee, Karen L.; Cahoon, Donald R.; Cherry, Julia A.; Megonigal, J. Patrick

    2009-01-01

    Tidal wetlands experiencing increased rates of sea-level rise (SLR) must increase rates of soil elevation gain to avoid permanent conversion to open water. The maximal rate of SLR that these ecosystems can tolerate depends partly on mineral sediment deposition, but the accumulation of organic matter is equally important for many wetlands. Plant productivity drives organic matter dynamics and is sensitive to global change factors, such as rising atmospheric CO2 concentration. It remains unknown how global change will influence organic mechanisms that determine future tidal wetland viability. Here, we present experimental evidence that plant response to elevated atmospheric [CO2] stimulates biogenic mechanisms of elevation gain in a brackish marsh. Elevated CO2 (ambient + 340 ppm) accelerated soil elevation gain by 3.9 mm yr−1 in this 2-year field study, an effect mediated by stimulation of below-ground plant productivity. Further, a companion greenhouse experiment revealed that the CO2 effect was enhanced under salinity and flooding conditions likely to accompany future SLR. Our results indicate that by stimulating biogenic contributions to marsh elevation, increases in the greenhouse gas, CO2, may paradoxically aid some coastal wetlands in counterbalancing rising seas. PMID:19325121

  8. Development of Simulator for High-Speed Elevator System

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Hyung Min; Kim, Sung Jun; Sul, Seung Ki; Seok, Ki Riong [Seoul National University, Seoul(Korea); Kwon, Tae Seok [Hanyang University, Seoul(Korea); Kim, Ki Su [Konkuk University, Seoul(Korea); Shim, Young Seok [Inha University, incheon(Korea)

    2002-02-01

    This paper describes the dynamic load simulator for high-speed elevator system, which can emulate 3-mass system as well as equivalent 1-mass system 1-mass system. In order to implement the equivalent inertia of entire elevator system, the conventional simulators have generally utilized the mechanical inertia(flywheel) with large radius, which makes the entire system large and heavy. In addition, the mechanical inertia should be replaced each time in order to test another elevator system. In this paper, the dynamic load simulation methods using electrical inertia are presented so that the volume and weight of simulator system are greatly reduced and the adjustment of inertia value can be achieved easily by software. Experimental results show the feasibility of this simulator system. (author). 5 refs., 7 figs., 2 tabs.

  9. Structural integrity analysis of the 224U elevator mothballing

    Energy Technology Data Exchange (ETDEWEB)

    Boehnke, W.M.

    1994-11-18

    As part of the preparation of Building 224U for turnover to Decontamination and Decommissioning, it is necessary to place the elevator in a mothballed condition so that it can be reactivated for use after 10 to 25 years. This mothballing is going to be accomplished by landing the counterweight on wooden timbers and suspending the elevator cab with wire rope or chain slings. This will take the load off the cables and make it relatively easy to reactive. The objective of this Supporting Document is to verify the structural integrity of all of the load bearing components involved in mothballing the 224U Building elevator. Building 224U is part of the UO{sub 3} Plant where uranyl nitrates from the PUREX Plant was converted to UO{sub 3} powder.

  10. The Supraspinatus and the Deltoid - not just two arm elevators.

    Science.gov (United States)

    de Witte, P B; Werner, S; ter Braak, L M; Veeger, H E J; Nelissen, R G H H; de Groot, J H

    2014-02-01

    The debate on the clinical and functional role of the Supraspinatus in relation to the Deltoid necessitates experimental assessment of their contributions to arm elevation. Our goal was to evaluate the responses of both muscles to increased elevation moment loading. Twenty-three healthy volunteers applied 30N elevation forces at the proximal and distal humerus, resulting in small and large glenohumeral elevation moment tasks. The responses of the Deltoid and Supraspinatus were recorded with surface and fine-wire electromyography, quantified by (EMGdistal-EMGproximal), and normalized by the summed activations (EMGdistal+EMGproximal) to RMuscle ratios. Deltoid activity increased with large elevation moment loading (RDE=.11, 95%-CI [.06-.16]). Surprisingly, there was no significant average increase in Supraspinatus activation (RSSp=.06, 95%-CI [-.08 to .20]) and its response was significantly more variable (Levene's test, F=11.7, p<.001). There was an inverse association between the responses (ß=-1.02, 95%-CI [-2.37 to .32]), indicating a potential complementary function of the Supraspinatus to the Deltoid. The Deltoid contributes to the glenohumeral elevation moment, but the contribution of the Supraspinatus is variable. We speculate there is inter-individual or intra-muscular function variability for the Supraspinatus, which may be related to the frequently reported variations in symptoms and treatment outcome of Supraspinatus pathologies. Copyright © 2013 Elsevier B.V. All rights reserved.

  11. Remaining lifetime modelling for replacement of power transformer populations

    NARCIS (Netherlands)

    Schijndel, van A.; Wetzer, J.; Wouters, P.A.A.F.

    2008-01-01

    The age of the majority of power transformers applied in the western electricity network varies between 25 and 50 years. Depending on the load history and time of operation, replacement on short term is imminent. A technically sound policy concerning the replacement of these assets must be based on

  12. Ruptured human Achilles tendon has elevated metabolic activity up to 1 year after repair

    DEFF Research Database (Denmark)

    Eliasson, Pernilla; Couppé, Christian; Lonsdale, Markus

    2016-01-01

    PURPOSE: Following Achilles tendon rupture, running is often allowed after 6 months. However, tendon healing is slow and the metabolic status of the tendon at this point is unknown. The purpose of this study was to investigate tendon metabolism (glucose uptake) and vascularization at 3, 6 and 12...... demonstrate that the healing process as determined by metabolic activity and vascularization continues for 6 months after injury when large loads are typically allowed on the tendon. Indeed, metabolic activity remained elevated for more than 1 year after injury despite normalized vascularization. The robust...... negative correlation between tendon metabolism and patient-reported outcome suggests that a high metabolic activity 6 months after the injury may be related to a poor clinical healing outcome....

  13. Group control of elevators

    Energy Technology Data Exchange (ETDEWEB)

    Umeda, Yasukazu; Hikita, Shiro; Tuji, Sintaro (Mitsubishi Electric Corp., Tokyo (Japan))

    1988-09-05

    Items to be evaluated in the group control of elevators, and a typical control system are described. A new system in which the fuzzy rule base is employed is introduced together with the configuration. The items to be evaluated are waiting time, riding time, accuracy of forecasting, energy saving, and ease of usage. The everage waiting time of less than 20 seconds with less than 3% waiting rate of more than 60 seconds is accepted as a satisfactory service condition. There are many conflicting matters in group-controlling, and the study for the controlling must deal with the optimization of multi-purpose problems. The standards for group-control evaluation differ according to building structures and the tastes of users, and an important problem is where to give emphasis of the evaluation. The TRAFFIC PATTERN LEARNING METHOD has been applied in the system for careful control to accommodate the traffic. No specific function is provided for the evaluation, but the call allocation is made by fuzzy rule-base. The configuration of a new group-control system is introduced. 7 references, 7 figures, 1 table.

  14. Complex motion in nonlinear-map model of elevators in energy-saving traffic

    Science.gov (United States)

    Nagatani, Takashi

    2011-05-01

    We have studied the dynamic behavior and dynamic transitions of elevators in a system for reducing energy consumption. We present a nonlinear-map model for the dynamics of M elevators. The motion of elevators depends on the loading parameter and their number M. The dependence of the fixed points on the loading parameter is derived. The dynamic transitions occur at 2(M-1) stages with increasing the value of loading parameter. At the dynamic transition point, the motion of elevators changes from a stable state to an unstable state and vice versa. The elevators display periodic motions with various periods in the unstable state. In the unstable state, the number of riding passengers fluctuates in a complex manner over various trips.

  15. Distribution load estimation (DLE)

    Energy Technology Data Exchange (ETDEWEB)

    Seppaelae, A; Lehtonen, M [VTT Energy, Espoo (Finland)

    1998-08-01

    The load research has produced customer class load models to convert the customers` annual energy consumption to hourly load values. The reliability of load models applied from a nation-wide sample is limited in any specific network because many local circumstances are different from utility to utility and time to time. Therefore there is a need to find improvements to the load models or, in general, improvements to the load estimates. In Distribution Load Estimation (DLE) the measurements from the network are utilized to improve the customer class load models. The results of DLE will be new load models that better correspond to the loading of the distribution network but are still close to the original load models obtained by load research. The principal data flow of DLE is presented

  16. Lærer-elev-relationer

    DEFF Research Database (Denmark)

    Laursen, Per Fibæk; Nielsen, Anne Maj

    2015-01-01

    I kapitlet belyser vi relationskompetence i forholdet mellem lærer og elever og hvordan læreren kan arbejde med forhold til elever og med sin opmærksomhed på relationsarbejdet. Afslutningsvis ser vi på hvordan lærere fortsat kan udvikle deres relationskompetence.......I kapitlet belyser vi relationskompetence i forholdet mellem lærer og elever og hvordan læreren kan arbejde med forhold til elever og med sin opmærksomhed på relationsarbejdet. Afslutningsvis ser vi på hvordan lærere fortsat kan udvikle deres relationskompetence....

  17. Tanzania Elevation and Surface Characteristics

    Data.gov (United States)

    US Agency for International Development — The dataset displays Elevation, Slope, Aspect, Topographic Position Index, Terrain Ruggedness, and Roughness based on Shuttle Radar Topography Mission (SRTM) (3...

  18. Cone Penetrometer Load Cell Temperature and Radiation Testing Results

    Energy Technology Data Exchange (ETDEWEB)

    Follett, Jordan R.

    2013-08-28

    This report summarizes testing activities performed at the Pacific Northwest National Laboratory to verify the cone penetrometer load cell can withstand the tank conditions present in 241-AN-101 and 241-AN-106. The tests demonstrated the load cell device will operate under the elevated temperature and radiation levels expected to be encountered during tank farm deployment of the device.

  19. High thermal load component

    International Nuclear Information System (INIS)

    Fuse, Toshiaki; Tachikawa, Nobuo.

    1996-01-01

    A cooling tube made of a pure copper is connected to the inner portion of an armour (heat resistant member) made of an anisotropic carbon/carbon composite (CFC) material. The CFC material has a high heat conductivity in longitudinal direction of fibers and has low conductivity in perpendicular thereto. Fibers extending in the armour from a heat receiving surface just above the cooling tube are directly connected to the cooling tube. A portion of the fibers extending from a heat receiving surface other than portions not just above the cooling tube is directly bonded to the cooling tube. Remaining fibers are disposed so as to surround the cooling tube. The armour and the cooling tube are soldered using an active metal flux. With such procedures, high thermal load components for use in a thermonuclear reactor are formed, which are excellent in a heat removing characteristic and hardly causes defects such as crackings and peeling. (I.N.)

  20. Instrument to determine prestress remaining in a damaged bridge girder

    Science.gov (United States)

    Civjan, Scott A.; Jirsa, James O.; Carrasquillo, Ramon L.; Fowler, David W.

    1998-03-01

    An instrument has been developed to estimate stress levels in prestress strands in existing members. The prototype instrument applies a lateral load to an exposed prestressing strand and measures the resulting displacements. The instrument was calibrated for 0.5-inch (12.7 mm) diameter seven-wire strand with exposed lengths of 1.5 feet (0.46 m) to 3.75 feet (1.14 m). It was tested to determine its accuracy, precision, and usefulness in the field. Strand forces were consistently estimated to within ten percent of the actual load. The device was also utilized in the placement of strand splices and was found to be more reliable in checking induced strand tensions than the standard torque wrench method.

  1. Distribution load estimation - DLE

    Energy Technology Data Exchange (ETDEWEB)

    Seppaelae, A. [VTT Energy, Espoo (Finland)

    1996-12-31

    The load research project has produced statistical information in the form of load models to convert the figures of annual energy consumption to hourly load values. The reliability of load models is limited to a certain network because many local circumstances are different from utility to utility and time to time. Therefore there is a need to make improvements in the load models. Distribution load estimation (DLE) is the method developed here to improve load estimates from the load models. The method is also quite cheap to apply as it utilises information that is already available in SCADA systems

  2. Distribution load estimation - DLE

    Energy Technology Data Exchange (ETDEWEB)

    Seppaelae, A [VTT Energy, Espoo (Finland)

    1997-12-31

    The load research project has produced statistical information in the form of load models to convert the figures of annual energy consumption to hourly load values. The reliability of load models is limited to a certain network because many local circumstances are different from utility to utility and time to time. Therefore there is a need to make improvements in the load models. Distribution load estimation (DLE) is the method developed here to improve load estimates from the load models. The method is also quite cheap to apply as it utilises information that is already available in SCADA systems

  3. A Bayesian Framework for Remaining Useful Life Estimation

    Data.gov (United States)

    National Aeronautics and Space Administration — The estimation of remaining useful life (RUL) of a faulty component is at the center of system prognostics and health management. It gives operators a potent tool in...

  4. Robotics to Enable Older Adults to Remain Living at Home

    OpenAIRE

    Pearce, Alan J.; Adair, Brooke; Miller, Kimberly; Ozanne, Elizabeth; Said, Catherine; Santamaria, Nick; Morris, Meg E.

    2012-01-01

    Given the rapidly ageing population, interest is growing in robots to enable older people to remain living at home. We conducted a systematic review and critical evaluation of the scientific literature, from 1990 to the present, on the use of robots in aged care. The key research questions were as follows: (1) what is the range of robotic devices available to enable older people to remain mobile, independent, and safe? and, (2) what is the evidence demonstrating that robotic devices are effec...

  5. Elevation dynamics in a restored versus a submerging salt marsh in Long Island Sound

    Science.gov (United States)

    Anisfeld, Shimon C.; Hill, Troy D.; Cahoon, Donald R.

    2016-01-01

    Accelerated sea-level rise (SLR) poses the threat of salt marsh submergence, especially in marshes that are relatively low-lying. At the same time, restoration efforts are producing new low-lying marshes, many of which are thriving and avoiding submergence. To understand the causes of these different fates, we studied two Long Island Sound marshes: one that is experiencing submergence and mudflat expansion, and one that is undergoing successful restoration. We examined sedimentation using a variety of methods, each of which captures different time periods and different aspects of marsh elevation change: surface-elevation tables, marker horizons, sediment cores, and sediment traps. We also studied marsh hydrology, productivity, respiration, nutrient content, and suspended sediment. We found that, despite the expansion of mudflat in the submerging marsh, the areas that remain vegetated have been gaining elevation at roughly the rate of SLR over the last 10 years. However, this elevation gain was only possible thanks to an increase in belowground volume, which may be a temporary response to waterlogging. In addition, accretion rates in the first half of the twentieth century were much lower than current rates, so century-scale accretion in the submerging marsh was lower than SLR. In contrast, at the restored marsh, accretion rates are now averaging about 10 mm yr−1 (several times the rate of SLR), much higher than before restoration. The main cause of the different trajectories at the two marshes appeared to be the availability of suspended sediment, which was much higher in the restored marsh. We considered and rejected alternative hypotheses, including differences in tidal flooding, plant productivity, and nutrient loading. In the submerging marsh, suspended and deposited sediment had relatively high organic content, which may be a useful indicator of sediment starvation.

  6. Elevation of the diaphragmatic cupola

    International Nuclear Information System (INIS)

    Semenov, V.M.; Talesnik, M.R.

    1988-01-01

    Altogether 45 patients with elevation of the diaphragmatic cupola were examined. A high frequency of erroneous initial interpretation of examination results was noted in inflammatory and tumorous lesions and congenital conditions. Routine and contrast methods (pneumoperitoneum, bronchography, pleurography and fistulography) were used. Disease-related methods of X-ray investigation were proposed. A variety of causes of diaphragm elevation was indicated

  7. Space Station tethered elevator system

    Science.gov (United States)

    Haddock, Michael H.; Anderson, Loren A.; Hosterman, K.; Decresie, E.; Miranda, P.; Hamilton, R.

    1989-01-01

    The optimized conceptual engineering design of a space station tethered elevator is presented. The tethered elevator is an unmanned, mobile structure which operates on a ten-kilometer tether spanning the distance between Space Station Freedom and a platform. Its capabilities include providing access to residual gravity levels, remote servicing, and transportation to any point along a tether. The report discusses the potential uses, parameters, and evolution of the spacecraft design. Emphasis is placed on the elevator's structural configuration and three major subsystem designs. First, the design of elevator robotics used to aid in elevator operations and tethered experimentation is presented. Second, the design of drive mechanisms used to propel the vehicle is discussed. Third, the design of an onboard self-sufficient power generation and transmission system is addressed.

  8. Forensic considerations when dealing with incinerated human dental remains.

    Science.gov (United States)

    Reesu, Gowri Vijay; Augustine, Jeyaseelan; Urs, Aadithya B

    2015-01-01

    Establishing the human dental identification process relies upon sufficient post-mortem data being recovered to allow for a meaningful comparison with ante-mortem records of the deceased person. Teeth are the most indestructible components of the human body and are structurally unique in their composition. They possess the highest resistance to most environmental effects like fire, desiccation, decomposition and prolonged immersion. In most natural as well as man-made disasters, teeth may provide the only means of positive identification of an otherwise unrecognizable body. It is imperative that dental evidence should not be destroyed through erroneous handling until appropriate radiographs, photographs, or impressions can be fabricated. Proper methods of physical stabilization of incinerated human dental remains should be followed. The maintenance of integrity of extremely fragile structures is crucial to the successful confirmation of identity. In such situations, the forensic dentist must stabilise these teeth before the fragile remains are transported to the mortuary to ensure preservation of possibly vital identification evidence. Thus, while dealing with any incinerated dental remains, a systematic approach must be followed through each stage of evaluation of incinerated dental remains to prevent the loss of potential dental evidence. This paper presents a composite review of various studies on incinerated human dental remains and discusses their impact on the process of human identification and suggests a step by step approach. Copyright © 2014 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

  9. Electric shock and elevated EMF levels due to triplen harmonics

    International Nuclear Information System (INIS)

    Tran, T.Q.; Conrad, L.E.; Stallman, B.K.

    1996-01-01

    The increasing use of single phase rectifiers for electric power conversion in residential applications increases harmonic load on utility systems. Many papers have analyzed the effect of these loads on power quality and equipment loadability. However, there are two more critical concerns for harmonic loads served phase to neutral on multi-grounded wye systems. Triplen harmonics, particularly the third, add in the neutral and have little diversity between loads. The higher neutral currents may cause significant problems. Neutral to earth voltages will increase near the substations which could increase stray voltage complaints. The additional neutral current on three phase lines will elevate EMF levels especially in the fringe areas. This paper provides fundamental understanding of triplen harmonic influence on stray voltage and EMF related to multi-grounded wye electric distribution systems

  10. The history of commonly used dental elevators.

    Science.gov (United States)

    Bussell, M A; Graham, R M

    2008-11-08

    Despite the extensive and regular use of dental elevators on a daily basis in both general dental and specialist oral and maxillofacial surgical practice, little is known about the history and origins of such instruments and this remains an intriguing question. This question has been the basis for the following article, which gives a brief history of the instruments, discusses their eponymous origins and the history, life and works of the individuals they are named after. In-depth research has also raised other questions about such instruments that could be the focus for further study.

  11. Shot loading platform analysis

    International Nuclear Information System (INIS)

    Norman, B.F.

    1994-01-01

    This document provides the wind/seismic analysis and evaluation for the shot loading platform. Hand calculations were used for the analysis. AISC and UBC load factors were used in this evaluation. The results show that the actual loads are under the allowable loads and all requirements are met

  12. Development of a remaining lifetime management system for NPPS

    International Nuclear Information System (INIS)

    Galvan, J.C.; Regano, M.; Hevia Ruperez, F.

    1994-01-01

    The interest evinced by Spain nuclear power plants in providing a tool to support remaining lifetime management led to UNESA's application to OCIDE in 1992, and the latter's approval, for financing the project to develop a Remaining Lifetime Evaluation System for LWR nuclear power plants. This project is currently being developed under UNESA leadership, and the collaboration of three Spanish engineering companies and a research centre. The paper will describe its objectives, activities, current status and prospects. The project is defined in two phases, the first consisting of the identification and analysis of the main ageing phenomena and their significant parameters and specification of the Remaining Lifetime Evaluation System (RLES), and the second implementation of a pilot application of the RLES to verify its effectiveness. (Author)

  13. On random age and remaining lifetime for populations of items

    DEFF Research Database (Denmark)

    Finkelstein, M.; Vaupel, J.

    2015-01-01

    We consider items that are incepted into operation having already a random (initial) age and define the corresponding remaining lifetime. We show that these lifetimes are identically distributed when the age distribution is equal to the equilibrium distribution of the renewal theory. Then we...... develop the population studies approach to the problem and generalize the setting in terms of stationary and stable populations of items. We obtain new stochastic comparisons for the corresponding population ages and remaining lifetimes that can be useful in applications. Copyright (c) 2014 John Wiley...

  14. Methodology for Extraction of Remaining Sodium of Used Sodium Containers

    International Nuclear Information System (INIS)

    Jung, Minhwan; Kim, Jongman; Cho, Youngil; Jeong, Jiyoung

    2014-01-01

    Sodium used as a coolant in the SFR (Sodium-cooled Fast Reactor) reacts easily with most elements due to its high reactivity. If sodium at high temperature leaks outside of a system boundary and makes contact with oxygen, it starts to burn and toxic aerosols are produced. In addition, it generates flammable hydrogen gas through a reaction with water. Hydrogen gas can be explosive within the range of 4.75 vol%. Therefore, the sodium should be handled carefully in accordance with standard procedures even though there is a small amount of target sodium remainings inside the containers and drums used for experiment. After the experiment, all sodium experimental apparatuses should be dismantled carefully through a series of draining, residual sodium extraction, and cleaning if they are no longer reused. In this work, a system for the extraction of the remaining sodium of used sodium drums has been developed and an operation procedure for the system has been established. In this work, a methodology for the extraction of remaining sodium out of the used sodium container has been developed as one of the sodium facility maintenance works. The sodium extraction system for remaining sodium of the used drums was designed and tested successfully. This work will contribute to an establishment of sodium handling technology for PGSFR. (Prototype Gen-IV Sodium-cooled Fast Reactor)

  15. Predicting the Remaining Useful Life of Rolling Element Bearings

    DEFF Research Database (Denmark)

    Hooghoudt, Jan Otto; Jantunen, E; Yi, Yang

    2018-01-01

    Condition monitoring of rolling element bearings is of vital importance in order to keep the industrial wheels running. In wind industry this is especially important due to the challenges in practical maintenance. The paper presents an attempt to improve the capability of prediction of remaining...

  16. The experiences of remaining nurse tutors during the transformation ...

    African Journals Online (AJOL)

    The transformation of public services and education in South Africa is part of the political and socioeconomic transition to democracy. Changes are occurring in every fi eld, including that of the health services. A qualitative study was undertaken to investigate the experiences of the remaining nurse tutors at a school of ...

  17. Remaining childless : Causes and consequences from a life course perspective

    NARCIS (Netherlands)

    Keizer, R.

    2010-01-01

    Little is know about childless individuals in the Netherlands, although currently one out of every five Dutch individuals remains childless. Who are they? How did they end up being childless? How and to what extent are their life outcomes influenced by their childlessness? By focusing on individual

  18. Molecular genetic identification of skeletal remains of apartheid ...

    African Journals Online (AJOL)

    The Truth and Reconciliation Commission made significant progress in examining abuses committed during the apartheid era in South Africa. Despite information revealed by the commission, a large number of individuals remained missing when the commission closed its proceedings. This provided the impetus for the ...

  19. Palmar, Patellar, and Pedal Human Remains from Pavlov

    Czech Academy of Sciences Publication Activity Database

    Trinkaus, E.; Wojtal, P.; Wilczyński, J.; Sázelová, Sandra; Svoboda, Jiří

    2017-01-01

    Roč. 2017, June (2017), s. 73-101 ISSN 1545-0031 Institutional support: RVO:68081758 Keywords : Gravettian * human remains * isolated bones * anatomically modern humans * Upper Paleolithic Subject RIV: AC - Archeology, Anthropology, Ethnology OBOR OECD: Archaeology http://paleoanthro.org/media/journal/content/PA20170073.pdf

  20. Robotics to Enable Older Adults to Remain Living at Home

    Directory of Open Access Journals (Sweden)

    Alan J. Pearce

    2012-01-01

    Full Text Available Given the rapidly ageing population, interest is growing in robots to enable older people to remain living at home. We conducted a systematic review and critical evaluation of the scientific literature, from 1990 to the present, on the use of robots in aged care. The key research questions were as follows: (1 what is the range of robotic devices available to enable older people to remain mobile, independent, and safe? and, (2 what is the evidence demonstrating that robotic devices are effective in enabling independent living in community dwelling older people? Following database searches for relevant literature an initial yield of 161 articles was obtained. Titles and abstracts of articles were then reviewed by 2 independent people to determine suitability for inclusion. Forty-two articles met the criteria for question 1. Of these, 4 articles met the criteria for question 2. Results showed that robotics is currently available to assist older healthy people and people with disabilities to remain independent and to monitor their safety and social connectedness. Most studies were conducted in laboratories and hospital clinics. Currently limited evidence demonstrates that robots can be used to enable people to remain living at home, although this is an emerging smart technology that is rapidly evolving.

  1. Authentic leadership: becoming and remaining an authentic nurse leader.

    Science.gov (United States)

    Murphy, Lin G

    2012-11-01

    This article explores how chief nurse executives became and remained authentic leaders. Using narrative inquiry, this qualitative study focused on the life stories of participants. Results demonstrate the importance of reframing, reflection in alignment with values, and the courage needed as nurse leaders progress to authenticity.

  2. Robotics to enable older adults to remain living at home.

    Science.gov (United States)

    Pearce, Alan J; Adair, Brooke; Miller, Kimberly; Ozanne, Elizabeth; Said, Catherine; Santamaria, Nick; Morris, Meg E

    2012-01-01

    Given the rapidly ageing population, interest is growing in robots to enable older people to remain living at home. We conducted a systematic review and critical evaluation of the scientific literature, from 1990 to the present, on the use of robots in aged care. The key research questions were as follows: (1) what is the range of robotic devices available to enable older people to remain mobile, independent, and safe? and, (2) what is the evidence demonstrating that robotic devices are effective in enabling independent living in community dwelling older people? Following database searches for relevant literature an initial yield of 161 articles was obtained. Titles and abstracts of articles were then reviewed by 2 independent people to determine suitability for inclusion. Forty-two articles met the criteria for question 1. Of these, 4 articles met the criteria for question 2. Results showed that robotics is currently available to assist older healthy people and people with disabilities to remain independent and to monitor their safety and social connectedness. Most studies were conducted in laboratories and hospital clinics. Currently limited evidence demonstrates that robots can be used to enable people to remain living at home, although this is an emerging smart technology that is rapidly evolving.

  3. Dinosaur remains from the type Maastrichtian: An update

    NARCIS (Netherlands)

    Weishampel, David B.; Mulder, Eric W A; Dortangs, Rudi W.; Jagt, John W M; Jianu, Coralia Maria; Kuypers, Marcel M M; Peeters, Hans H G; Schulp, Anne S.

    1999-01-01

    Isolated cranial and post-cranial remains of hadrosaurid dinosaurs have been collected from various outcrops in the type area of the Maastrichtian stage during the last few years. In the present contribution, dentary and maxillary teeth are recorded from the area for the first time. Post-cranial

  4. Risk-based management of remaining life of power plant components

    International Nuclear Information System (INIS)

    Roos, E.; Jovanovic, A.S.; Maile, K.; Auerkari, P.

    1999-01-01

    The paper describes application of different modules of the MPA-System ALIAS in risk-based management of remaining life of power plant components. The system allows comprehensive coverage of all aspects of the remaining life management, including also the risk analysis and risk management. In addition, thanks to the modular character of the system it is also possible to implement new methods: In the case described here, a new (probabilistic) method for determination of the next inspection time for the components exposed to creep loading has been developed and implemented in the system. Practical application of the method has shown (a) that the mean values obtained by the method fall into the range of results obtained by other methods (based on expert knowledge), and (b) that it is possible to quantify the probability of aberration from the mean values. This in turn allows quantifying the additional risks linked to e.g. prolonging of inspection intervals. (orig.) [de

  5. Rangeland -- plant response to elevated CO2

    International Nuclear Information System (INIS)

    Owensby, C.E.; Coyne, P.I.; Ham, J.M.; Parton, W.; Rice, C.; Auen, L.M.; Adam, N.

    1993-01-01

    Plots of a tallgrass prairie ecosystem were exposed to ambient and twice-ambient CO 2 concentrations in open-top chambers and compared to unchambered ambient CO 2 plots during the entire growing season from 1989 through 1992. Relative root production among treatments was estimated using root ingrowth bags which remained in place throughout the growing season. Latent heat flux was simulated with and without water stress. Botanical composition was estimated annuallyin all treatments. Open-top chambers appeared to reduce latent heat flux and increase water use efficiency similar to elevated CO 2 when water stress was not severe, but under severe water stress, chamber effect on water use efficiency was limited. In natural ecosystems with periodic moisture stress, increased water use efficiency under elevated CO 2 apparently would have a greater impact on productivity than photosynthetic pathway. Root ingrowth biomass was greater in 1990 and 1991 on elevated CO 2 plots compared to ambient or chambered-ambient plots. In 1992, there was no difference in root ingrowth biomass among treatments

  6. Context-Aware Elevator Scheduling

    OpenAIRE

    Strang, Thomas; Bauer, Christian

    2007-01-01

    Research on context-aware systems is usually user-centric and thus focussed on the context of a specific user to serve his or her needs in an optimized way. In this paper, we want to apply core concepts developed in research on context-awareness in a system-centric way, namely to elevator systems. We show with three different examples that the performance of an elevator system can be significantly improved if the elevator control has access to contextual knowledge. The first example demons...

  7. Role of myocardial ischemia on exercise-induced ST elevation

    International Nuclear Information System (INIS)

    Saito, Muneyasu; Sumiyoshi, Tetsuya; Nishimura, Tsunehiko; Uehara, Toshiisa; Hayashida, Kouhei; Haze, Kazuo; Fukami, Ken-ichi; Hiramori, Katsuhiko

    1986-01-01

    Exercise-induced ST elevation in patients with previous myocardial infarction (MI) has been recognized to be related to left ventricular (LV) asynergy, however it is also recognized that myocardial ischemia can induce ST elevation. In this study, factors which determine the extent of ST elevation, with special reference to myocardial ischemia, was re-evaluated using quantitative analysis of stress myocardial scintigraphy (S-SG). Among 65 patients with previous anterior myocardial infarction and documented single vessel disease of left anterior descending artery (LAD), 19 patients who had exercise-induced ST elevation (ΔST ≥ 2.0 mm) had more abnormal Q waves (p < 0.01), lower LV ejection fraction (EF) (p < 0.01), more severe LV asynergy (p < 0.05) and less incidence of post-MI angina pectoris (AP) (p < 0.01), compared to those with ΔST < 2.0 mm, indicating that ST elevation is primarily related to LV asynergy. Correlation studies among clinical, angiographic and scintigraphic parameters show that ΔST was significantly related to a size of MI represented by Tl score or relative defect Tl activity and number of abnormal Q waves (No.Q), the magnitude of work load expressed by changes in double product (ΔDP) and intervals between the onset and exercise test, as well as myocardial ischemia expressed by the extent of redistribution (%RD) in S-SG. Among 23 patients with post-MI AP, ΔST significantly correlated with %RD (r = 0.47), indicating that myocardial ischemia can be a mechanism of exercise-induced ST elevation in patients with previous MI. Furtheremore, among those with ST elevation, concave-type ST elevation was more related to myocardial ischemia compared to convex-type ST elevation as expressed by the incidence of post-MI AP and/or significant redistribution. (J.P.N.)

  8. Complex motion in nonlinear-map model of elevators in energy-saving traffic

    International Nuclear Information System (INIS)

    Nagatani, Takashi

    2011-01-01

    We have studied the dynamic behavior and dynamic transitions of elevators in a system for reducing energy consumption. We present a nonlinear-map model for the dynamics of M elevators. The motion of elevators depends on the loading parameter and their number M. The dependence of the fixed points on the loading parameter is derived. The dynamic transitions occur at 2(M-1) stages with increasing the value of loading parameter. At the dynamic transition point, the motion of elevators changes from a stable state to an unstable state and vice versa. The elevators display periodic motions with various periods in the unstable state. In the unstable state, the number of riding passengers fluctuates in a complex manner over various trips. - Highlights: → We propose the nonlinear-map model in energy-saving traffic of elevators. → We study the dynamical behavior and dynamical transitions in the system of elevators. → We derive the fixed point of the nonlinear map analytically. → We clarify the dependence of the motion on the loading parameter and the number.

  9. Complex motion in nonlinear-map model of elevators in energy-saving traffic

    Energy Technology Data Exchange (ETDEWEB)

    Nagatani, Takashi, E-mail: tmtnaga@ipc.shizuoka.ac.j [Department of Mechanical Engineering, Division of Thermal Science, Shizuoka University, Hamamatsu 432-8561 (Japan)

    2011-05-16

    We have studied the dynamic behavior and dynamic transitions of elevators in a system for reducing energy consumption. We present a nonlinear-map model for the dynamics of M elevators. The motion of elevators depends on the loading parameter and their number M. The dependence of the fixed points on the loading parameter is derived. The dynamic transitions occur at 2(M-1) stages with increasing the value of loading parameter. At the dynamic transition point, the motion of elevators changes from a stable state to an unstable state and vice versa. The elevators display periodic motions with various periods in the unstable state. In the unstable state, the number of riding passengers fluctuates in a complex manner over various trips. - Highlights: We propose the nonlinear-map model in energy-saving traffic of elevators. We study the dynamical behavior and dynamical transitions in the system of elevators. We derive the fixed point of the nonlinear map analytically. We clarify the dependence of the motion on the loading parameter and the number.

  10. Loads and loads and loads: the influence of prospective load, retrospective load, and ongoing task load in prospective memory

    Science.gov (United States)

    Meier, Beat; Zimmermann, Thomas D.

    2015-01-01

    In prospective memory tasks different kinds of load can occur. Adding a prospective memory task can impose a load on ongoing task performance. Adding ongoing task load (OTL) can affect prospective memory performance. The existence of multiple target events increases prospective load (PL) and adding complexity to the to-be-remembered action increases retrospective load (RL). In two experiments, we systematically examined the effects of these different types of load on prospective memory performance. Results showed an effect of PL on costs in the ongoing task for categorical targets (Experiment 2), but not for specific targets (Experiment 1). RL and OTL both affected remembering the retrospective component of the prospective memory task. We suggest that PL can enhance costs in the ongoing task due to additional monitoring requirements. RL and OTL seem to impact the division of resources between the ongoing task and retrieval of the retrospective component, which may affect disengagement from the ongoing task. In general, the results demonstrate that the different types of load affect prospective memory differentially. PMID:26082709

  11. Loads and loads and loads: the influence of prospective load, retrospective load, and ongoing task load in prospective memory.

    Science.gov (United States)

    Meier, Beat; Zimmermann, Thomas D

    2015-01-01

    In prospective memory tasks different kinds of load can occur. Adding a prospective memory task can impose a load on ongoing task performance. Adding ongoing task load (OTL) can affect prospective memory performance. The existence of multiple target events increases prospective load (PL) and adding complexity to the to-be-remembered action increases retrospective load (RL). In two experiments, we systematically examined the effects of these different types of load on prospective memory performance. Results showed an effect of PL on costs in the ongoing task for categorical targets (Experiment 2), but not for specific targets (Experiment 1). RL and OTL both affected remembering the retrospective component of the prospective memory task. We suggest that PL can enhance costs in the ongoing task due to additional monitoring requirements. RL and OTL seem to impact the division of resources between the ongoing task and retrieval of the retrospective component, which may affect disengagement from the ongoing task. In general, the results demonstrate that the different types of load affect prospective memory differentially.

  12. FEMA DFIRM Base Flood Elevations

    Data.gov (United States)

    Minnesota Department of Natural Resources — The Base Flood Elevation (BFE) table is required for any digital data where BFE lines will be shown on the corresponding Flood Insurance Rate Map (FIRM). Normally,...

  13. Advanced energy saving hydraulic elevator

    Energy Technology Data Exchange (ETDEWEB)

    Garrido, A.; Sevilleja, J.; Servia, A.

    1993-08-24

    An hydraulic elevator is described comprising: a counterweighted elevator comprising a car, a counterweight, and a rope connecting the car and the counterweight; a ram having a first reaction surface for driving one of the car or the counterweight upwardly and a second reaction surface for driving one of the car or the counterweight downwardly; multiplier means for moving the car a distance greater than a stroke of the ram, the multiplier means connecting the ram to the counterweighted elevator, the multiplier means comprising: a first pulley; a second pulley; means for rigidly connecting the first and second pulley, the means having a length corresponding to a rise of the hydraulic elevator, the means attaching to the ram; and a pulley rope which: has a first end attaching to a first fixed point, extends about the first pulley, extends about the second pulley, and has a second end attaching to a second fixed point.

  14. Space Elevators Preliminary Architectural View

    Science.gov (United States)

    Pullum, L.; Swan, P. A.

    Space Systems Architecture has been expanded into a process by the US Department of Defense for their large scale systems of systems development programs. This paper uses the steps in the process to establishes a framework for Space Elevator systems to be developed and provides a methodology to manage complexity. This new approach to developing a family of systems is based upon three architectural views: Operational View OV), Systems View (SV), and Technical Standards View (TV). The top level view of the process establishes the stages for the development of the first Space Elevator and is called Architectural View - 1, Overview and Summary. This paper will show the guidelines and steps of the process while focusing upon components of the Space Elevator Preliminary Architecture View. This Preliminary Architecture View is presented as a draft starting point for the Space Elevator Project.

  15. Coastal Digital Elevation Models (DEMs)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Digital elevation models (DEMs) of U.S. and other coasts that typically integrate ocean bathymetry and land topography. The DEMs support NOAA's mission to understand...

  16. Base Flood Elevation (BFE) Lines

    Data.gov (United States)

    Department of Homeland Security — The Base Flood Elevation (BFE) table is required for any digital data where BFE lines will be shown on the corresponding Flood Insurance Rate Map (FIRM). Normally if...

  17. Elevated Fixed Platform Test Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Elevated Fixed Platform (EFP) is a helicopter recovery test facility located at Lakehurst, NJ. It consists of a 60 by 85 foot steel and concrete deck built atop...

  18. Safety provision for nuclear power plants during remaining running time

    International Nuclear Information System (INIS)

    Rossnagel, Alexander; Hentschel, Anja

    2012-01-01

    With the phasing-out of the industrial use of nuclear energy for the power generation, the risk of the nuclear power plants has not been eliminated in principle, but only for a limited period of time. Therefore, the remaining nine nuclear power plants must also be used for the remaining ten years according to the state of science and technology. Regulatory authorities must substantiate the safety requirements for each nuclear power plant and enforce these requirements by means of various regulatory measures. The consequences of Fukushima must be included in the assessment of the safety level of nuclear power plants in Germany. In this respect, the regulatory authorities have the important tasks to investigate and assess the security risks as well as to develop instructions and orders.

  19. Structural remains at the early mediaeval fort at Raibania, Orissa

    Directory of Open Access Journals (Sweden)

    Bratati Sen

    2013-11-01

    Full Text Available The fortifications of mediaeval India occupy an eminent position in the history of military architecture. The present paper deals with the preliminary study of the structural remains at the early mediaeval fort at Raibania in the district of Balasore in Orissa. The fort was built of stone very loosely kept together. The three-walled fortification interspersed by two consecutive moats, a feature evidenced at Raibania, which is unparallel in the history of ancient and mediaeval forts and fortifications in India. Several other structures like the Jay-Chandi Temple Complex, a huge well, numerous tanks and remains of an ancient bridge add to the uniqueness of the Fort in the entire eastern region.

  20. Mineral remains of early life on Earth? On Mars?

    Science.gov (United States)

    Iberall, Robbins E.; Iberall, A.S.

    1991-01-01

    The oldest sedimentary rocks on Earth, the 3.8-Ga Isua Iron-Formation in southwestern Greenland, are metamorphosed past the point where organic-walled fossils would remain. Acid residues and thin sections of these rocks reveal ferric microstructures that have filamentous, hollow rod, and spherical shapes not characteristic of crystalline minerals. Instead, they resemble ferric-coated remains of bacteria. Because there are no earlier sedimentary rocks to study on Earth, it may be necessary to expand the search elsewhere in the solar system for clues to any biotic precursors or other types of early life. A study of morphologies of iron oxide minerals collected in the southern highlands during a Mars sample return mission may therefore help to fill in important gaps in the history of Earth's earliest biosphere. -from Authors

  1. USING CONDITION MONITORING TO PREDICT REMAINING LIFE OF ELECTRIC CABLES

    International Nuclear Information System (INIS)

    LOFARO, R.; SOO, P.; VILLARAN, M.; GROVE, E.

    2001-01-01

    Electric cables are passive components used extensively throughout nuclear power stations to perform numerous safety and non-safety functions. It is known that the polymers commonly used to insulate the conductors on these cables can degrade with time; the rate of degradation being dependent on the severity of the conditions in which the cables operate. Cables do not receive routine maintenance and, since it can be very costly, they are not replaced on a regular basis. Therefore, to ensure their continued functional performance, it would be beneficial if condition monitoring techniques could be used to estimate the remaining useful life of these components. A great deal of research has been performed on various condition monitoring techniques for use on electric cables. In a research program sponsored by the U.S. Nuclear Regulatory Commission, several promising techniques were evaluated and found to provide trendable information on the condition of low-voltage electric cables. These techniques may be useful for predicting remaining life if well defined limiting values for the aging properties being measured can be determined. However, each technique has advantages and limitations that must be addressed in order to use it effectively, and the necessary limiting values are not always easy to obtain. This paper discusses how condition monitoring measurements can be used to predict the remaining useful life of electric cables. The attributes of an appropriate condition monitoring technique are presented, and the process to be used in estimating the remaining useful life of a cable is discussed along with the difficulties that must be addressed

  2. Study on remain actinides recovery in pyro reprocessing

    International Nuclear Information System (INIS)

    Suharto, Bambang

    1996-01-01

    The spent fuel reprocessing by dry process called pyro reprocessing have been studied. Most of U, Pu and MA (minor actinides) from the spent fuel will be recovered and be fed back to the reactor as new fuel. Accumulation of remain actinides will be separated by extraction process with liquid cadmium solvent. The research was conducted by computer simulation to calculate the stage number required. The calculation's results showed on the 20 stages extractor more than 99% actinides can be separated. (author)

  3. US GAAP vs. IFRS – A COMPARISON OF REMAINING DIFFERENCES

    OpenAIRE

    Mihelčić, Eva

    2008-01-01

    In spite of the on-going harmonization process, there are still some differences between US GAAP and IFRS. Currently, companies listed on the New York Stock Exchange, which are reporting according to IFRS, must still prepare the reconciliation to US GAAP, to show the financial statements compliant with US GAAP as well. This article presents an overview of the remaining major differences between US GAAP and IFRS, descriptive as well as table-wise. First, the standards compared are shortly intr...

  4. Structural remains at the early mediaeval fort at Raibania, Orissa

    OpenAIRE

    Sen, Bratati

    2013-01-01

    The fortifications of mediaeval India occupy an eminent position in the history of military architecture. The present paper deals with the preliminary study of the structural remains at the early mediaeval fort at Raibania in the district of Balasore in Orissa. The fort was built of stone very loosely kept together. The three-walled fortification interspersed by two consecutive moats, a feature evidenced at Raibania, w...

  5. Neanderthal infant and adult infracranial remains from Marillac (Charente, France).

    Science.gov (United States)

    Dolores Garralda, María; Maureille, Bruno; Vandermeersch, Bernard

    2014-09-01

    At the site of Marillac, near the Ligonne River in Marillac-le-Franc (Charente, France), a remarkable stratigraphic sequence has yielded a wealth of archaeological information, palaeoenvironmental data, as well as faunal and human remains. Marillac must have been a sinkhole used by Neanderthal groups as a hunting camp during MIS 4 (TL date 57,600 ± 4,600BP), where Quina Mousterian lithics and fragmented bones of reindeer predominate. This article describes three infracranial skeleton fragments. Two of them are from adults and consist of the incomplete shafts of a right radius (Marillac 24) and a left fibula (Marillac 26). The third fragment is the diaphysis of the right femur of an immature individual (Marillac 25), the size and shape of which resembles those from Teshik-Tash and could be assigned to a child of a similar age. The three fossils have been compared with the remains of other Neanderthals or anatomically Modern Humans (AMH). Furthermore, the comparison of the infantile femora, Marillac 25 and Teshik-Tash, with the remains of several European children from the early Middle Ages clearly demonstrates the robustness and rounded shape of both Neanderthal diaphyses. Evidence of peri-mortem manipulations have been identified on all three bones, with spiral fractures, percussion pits and, in the case of the radius and femur, unquestionable cutmarks made with flint implements, probably during defleshing. Traces of periostosis appear on the fibula fragment and on the immature femoral diaphysis, although their aetiology remains unknown. Copyright © 2014 Wiley Periodicals, Inc.

  6. Calibration of C-14 dates: some remaining uncertainties and limitations

    International Nuclear Information System (INIS)

    Burleigh, R.

    1975-01-01

    A brief review is presented of the interpretation of radiocarbon dates in terms of calendar years. An outline is given of the factors that make such correlations necessary and of the work that has so far been done to make them possible. The calibration of the C-14 timescale very largely depends at present on the bristlecone pine chronology, but it is clear that many detailed uncertainties still remain. These are discussed. (U.K.)

  7. Prognostic modelling options for remaining useful life estimation by industry

    Science.gov (United States)

    Sikorska, J. Z.; Hodkiewicz, M.; Ma, L.

    2011-07-01

    Over recent years a significant amount of research has been undertaken to develop prognostic models that can be used to predict the remaining useful life of engineering assets. Implementations by industry have only had limited success. By design, models are subject to specific assumptions and approximations, some of which are mathematical, while others relate to practical implementation issues such as the amount of data required to validate and verify a proposed model. Therefore, appropriate model selection for successful practical implementation requires not only a mathematical understanding of each model type, but also an appreciation of how a particular business intends to utilise a model and its outputs. This paper discusses business issues that need to be considered when selecting an appropriate modelling approach for trial. It also presents classification tables and process flow diagrams to assist industry and research personnel select appropriate prognostic models for predicting the remaining useful life of engineering assets within their specific business environment. The paper then explores the strengths and weaknesses of the main prognostics model classes to establish what makes them better suited to certain applications than to others and summarises how each have been applied to engineering prognostics. Consequently, this paper should provide a starting point for young researchers first considering options for remaining useful life prediction. The models described in this paper are Knowledge-based (expert and fuzzy), Life expectancy (stochastic and statistical), Artificial Neural Networks, and Physical models.

  8. Remaining useful life estimation based on discriminating shapelet extraction

    International Nuclear Information System (INIS)

    Malinowski, Simon; Chebel-Morello, Brigitte; Zerhouni, Noureddine

    2015-01-01

    In the Prognostics and Health Management domain, estimating the remaining useful life (RUL) of critical machinery is a challenging task. Various research topics including data acquisition, fusion, diagnostics and prognostics are involved in this domain. This paper presents an approach, based on shapelet extraction, to estimate the RUL of equipment. This approach extracts, in an offline step, discriminative rul-shapelets from an history of run-to-failure data. These rul-shapelets are patterns that are selected for their correlation with the remaining useful life of the equipment. In other words, every selected rul-shapelet conveys its own information about the RUL of the equipment. In an online step, these rul-shapelets are compared to testing units and the ones that match these units are used to estimate their RULs. Therefore, RUL estimation is based on patterns that have been selected for their high correlation with the RUL. This approach is different from classical similarity-based approaches that attempt to match complete testing units (or only late instants of testing units) with training ones to estimate the RUL. The performance of our approach is evaluated on a case study on the remaining useful life estimation of turbofan engines and performance is compared with other similarity-based approaches. - Highlights: • A data-driven RUL estimation technique based on pattern extraction is proposed. • Patterns are extracted for their correlation with the RUL. • The proposed method shows good performance compared to other techniques

  9. Direct dating of Early Upper Palaeolithic human remains from Mladec.

    Science.gov (United States)

    Wild, Eva M; Teschler-Nicola, Maria; Kutschera, Walter; Steier, Peter; Trinkaus, Erik; Wanek, Wolfgang

    2005-05-19

    The human fossil assemblage from the Mladec Caves in Moravia (Czech Republic) has been considered to derive from a middle or later phase of the Central European Aurignacian period on the basis of archaeological remains (a few stone artefacts and organic items such as bone points, awls, perforated teeth), despite questions of association between the human fossils and the archaeological materials and concerning the chronological implications of the limited archaeological remains. The morphological variability in the human assemblage, the presence of apparently archaic features in some specimens, and the assumed early date of the remains have made this fossil assemblage pivotal in assessments of modern human emergence within Europe. We present here the first successful direct accelerator mass spectrometry radiocarbon dating of five representative human fossils from the site. We selected sample materials from teeth and from one bone for 14C dating. The four tooth samples yielded uncalibrated ages of approximately 31,000 14C years before present, and the bone sample (an ulna) provided an uncertain more-recent age. These data are sufficient to confirm that the Mladec human assemblage is the oldest cranial, dental and postcranial assemblage of early modern humans in Europe and is therefore central to discussions of modern human emergence in the northwestern Old World and the fate of the Neanderthals.

  10. Remaining life diagnosis method and device for nuclear reactor

    International Nuclear Information System (INIS)

    Yamamoto, Michiyoshi.

    1996-01-01

    A neutron flux measuring means is inserted from the outside of a reactor pressure vessel during reactor operation to forecast neutron-degradation of materials of incore structural components in the vicinity of portions to be measured based on the measured values, and the remaining life of the reactor is diagnosed by the forecast degraded state. In this case, the neutron fluxes to be measured are desirably fast and/or medium neutron fluxes. As the positions where the measuring means is to be inserted, for example, the vicinity of the structural components at the periphery of the fuel assembly is selected. Aging degradation characteristics of the structural components are determined by using the aging degradation data for the structural materials. The remaining life is analyzed based on obtained aging degradation characteristics and stress evaluation data of the incore structural components at portions to be measured. Neutron irradiation amount of structural components at predetermined positions can be recognized accurately, and appropriate countermeasures can be taken depending on the forecast remaining life thereby enabling to improve the reliability of the reactor. (N.H.)

  11. Postmortem Scavenging of Human Remains by Domestic Cats

    Directory of Open Access Journals (Sweden)

    Ananya Suntirukpong, M.D.

    2017-11-01

    Full Text Available Objective: Crime scene investigators, forensic medicine doctors and pathologists, and forensic anthropologists frequently encounter postmortem scavenging of human remains by household pets. Case presentation: The authors present a case report of a partially skeletonized adult male found dead after more than three months in his apartment in Thailand. The body was in an advanced stage of decomposition with nearly complete skeletonization of the head, neck, hands, and feet. The presence of maggots and necrophagous (flesh eating beetles on the body confirmed that insects had consumed much of the soft tissues. Examination of the hand and foot bones revealed canine tooth puncture marks. Evidence of chewing indicated that one or more of the decedent’s three house cats had fed on the body after death. Recognizing and identifying carnivore and rodent activity on the soft flesh and bones of human remains is important in interpreting and reconstructing postmortem damage. Thorough analysis may help explain why skeletal elements are missing, damaged, or out of anatomical position. Conclusion: This report presents a multi-disciplinary approach combining forensic anthropology and forensic medicine in examining and interpreting human remains.

  12. Train hard, sleep well? Perceived training load, sleep quantity and sleep stage distribution in elite level athletes.

    Science.gov (United States)

    Knufinke, Melanie; Nieuwenhuys, Arne; Geurts, Sabine A E; Møst, Els I S; Maase, Kamiel; Moen, Maarten H; Coenen, Anton M L; Kompier, Michiel A J

    2018-04-01

    Sleep is essential for recovery and performance in elite athletes. While it is generally assumed that exercise benefits sleep, high training load may jeopardize sleep and hence limit adequate recovery. To examine this, the current study assessed objective sleep quantity and sleep stage distributions in elite athletes and calculated their association with perceived training load. Mixed-methods. Perceived training load, actigraphy and one-channel EEG recordings were collected among 98 elite athletes during 7 consecutive days of regular training. Actigraphy revealed total sleep durations of 7:50±1:08h, sleep onset latencies of 13±15min, wake after sleep onset of 33±17min and sleep efficiencies of 88±5%. Distribution of sleep stages indicated 51±9% light sleep, 21±8% deep sleep, and 27±7% REM sleep. On average, perceived training load was 5.40±2.50 (scale 1-10), showing large daily variability. Mixed-effects models revealed no alteration in sleep quantity or sleep stage distributions as a function of day-to-day variation in preceding training load (all p's>.05). Results indicate healthy sleep durations, but elevated wake after sleep onset, suggesting a potential need for sleep optimization. Large proportions of deep sleep potentially reflect an elevated recovery need. With sleep quantity and sleep stage distributions remaining irresponsive to variations in perceived training load, it is questionable whether athletes' current sleep provides sufficient recovery after strenuous exercise. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  13. Coastal sediment elevation change following anthropogenic mangrove clearing

    Science.gov (United States)

    Hayden, Heather L.; Granek, Elise F.

    2015-11-01

    Coastal mangrove forests along tropical shorelines serve as an important interface between land and sea. They provide a physical buffer protecting the coastline from erosion and act as sediment "traps" catching terrestrial sediment, thus preventing smothering of subtidal coral reefs. Coastal development that removes mangrove habitat may impact adjacent nearshore coral reefs through sedimentation and nutrient loading. We examined differences in sediment elevation change between patches of open-coast intact and anthropogenically cleared red mangroves (Rhizophora mangle) on the east side of Turneffe Atoll, Belize, to quantify changes following mangrove clearing. Samples were collected over a 24 month period at five study sites, each containing paired intact (+mangrove) and cleared (-mangrove) plots. Five sediment elevation pins were deployed in each plot: behind areas cleared of mangroves (-mangrove) and behind adjacent intact mangroves (+mangrove). Sediment elevation increased at intact mangrove sites (M = +3.83 mm, SE = 0.95) whereas cleared mangrove areas suffered elevation loss (M = -7.30 mm, SE = 3.38). Mangroves inshore of partial or continuous gaps in the adjacent fringing reefs had higher rates of elevation loss (M = -15.05 mm) than mangroves inshore of continuous fringing reefs (M = -1.90 mm). Our findings provide information on potential effects of mangrove clearing and the role of offshore habitat characteristics on coastal sediment trapping and maintenance of sediment elevation by mangroves. With implications for coastline capacity to adjust to sea level rise, these findings are relevant to management of coastal fringing mangrove forests across the Caribbean.

  14. Fine scale vegetation classification and fuel load mapping for prescribed burning

    Science.gov (United States)

    Andrew D. Bailey; Robert Mickler

    2007-01-01

    Fire managers in the Coastal Plain of the Southeastern United States use prescribed burning as a tool to reduce fuel loads in a variety of vegetation types, many of which have elevated fuel loads due to a history of fire suppression. While standardized fuel models are useful in prescribed burn planning, those models do not quantify site-specific fuel loads that reflect...

  15. Modeling transport of nutrients & sediment loads into Lake Tahoe under climate change

    Science.gov (United States)

    Riverson, John; Coats, Robert; Costa-Cabral, Mariza; Dettinger, Mike; Reuter, John; Sahoo, Goloka; Schladow, Geoffrey

    2013-01-01

    The outputs from two General Circulation Models (GCMs) with two emissions scenarios were downscaled and bias-corrected to develop regional climate change projections for the Tahoe Basin. For one model—the Geophysical Fluid Dynamics Laboratory or GFDL model—the daily model results were used to drive a distributed hydrologic model. The watershed model used an energy balance approach for computing evapotranspiration and snowpack dynamics so that the processes remain a function of the climate change projections. For this study, all other aspects of the model (i.e. land use distribution, routing configuration, and parameterization) were held constant to isolate impacts of climate change projections. The results indicate that (1) precipitation falling as rain rather than snow will increase, starting at the current mean snowline, and moving towards higher elevations over time; (2) annual accumulated snowpack will be reduced; (3) snowpack accumulation will start later; and (4) snowmelt will start earlier in the year. Certain changes were masked (or counter-balanced) when summarized as basin-wide averages; however, spatial evaluation added notable resolution. While rainfall runoff increased at higher elevations, a drop in total precipitation volume decreased runoff and fine sediment load from the lower elevation meadow areas and also decreased baseflow and nitrogen loads basin-wide. This finding also highlights the important role that the meadow areas could play as high-flow buffers under climatic change. Because the watershed model accounts for elevation change and variable meteorological patterns, it provided a robust platform for evaluating the impacts of projected climate change on hydrology and water quality.

  16. Wind Loads on Structures

    DEFF Research Database (Denmark)

    Dyrbye, Claes; Hansen, Svend Ole

    Wind loads have to be taken into account when designing civil engineering structures. The wind load on structures can be systematised by means of the wind load chain: wind climate (global), terrain (wind at low height), aerodynamic response (wind load to pressure), mechanical response (wind...... pressure to structural response) and design criteria. Starting with an introduction of the wind load chain, the book moves on to meteorological considerations, atmospheric boundary layer, static wind load, dynamic wind load and scaling laws used in wind-tunnel tests. The dynamic wind load covers vibrations...... induced by wind turbulence, vortex shedding, flutter and galloping. The book gives a comprehensive treatment of wind effects on structures and it will be useful for consulting engineers designing wind-sensitive structures. It will also be valuable for students of civil engineering as textbook...

  17. Carbohydrate-Loading Diet

    Science.gov (United States)

    ... Grape juice (12 ounces) 55 225 Lunch Milk, chocolate, reduced fat (12 ounces) 45 285 4 slices ... usual during carbohydrate loading to get the same benefits as a man does. Despite carbohydrate loading, you ...

  18. Autonomous Propellant Loading Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The AES Autonomous Propellant Loading (APL) project consists of three activities. The first is to develop software that will automatically control loading of...

  19. Fuel pellet loading apparatus

    International Nuclear Information System (INIS)

    1980-01-01

    Apparatus is described for loading a predetermined amount of nuclear fuel pellets into nuclear fuel elements and particularly for the automatic loading of fuel pellets from within a sealed compartment. (author)

  20. Tuberculosis remains a challenge despite economic growth in Panama.

    Science.gov (United States)

    Tarajia, M; Goodridge, A

    2014-03-01

    Tuberculosis (TB) is a disease associated with inequality, and wise investment of economic resources is considered critical to its control. Panama has recently secured its status as an upper-middle-income country with robust economic growth. However, the prioritisation of resources for TB control remains a major challenge. In this article, we highlight areas that urgently require action to effectively reduce TB burden to minimal levels. Our conclusions suggest the need for fund allocation and a multidisciplinary approach to ensure prompt laboratory diagnosis, treatment assurance and workforce reinforcement, complemented by applied and operational research, development and innovation.

  1. Yellow Fever Remains a Potential Threat to Public Health.

    Science.gov (United States)

    Vasconcelos, Pedro F C; Monath, Thomas P

    2016-08-01

    Yellow fever (YF) remains a serious public health threat in endemic countries. The recent re-emergence in Africa, initiating in Angola and spreading to Democratic Republic of Congo and Uganda, with imported cases in China and Kenya is of concern. There is such a shortage of YF vaccine in the world that the World Health Organization has proposed the use of reduced doses (1/5) during emergencies. In this short communication, we discuss these and other problems including the risk of spread of YF to areas free of YF for decades or never before affected by this arbovirus disease.

  2. The Artificial Leaf: Recent Progress and Remaining Challenges

    Directory of Open Access Journals (Sweden)

    Mark D Symes

    2016-12-01

    Full Text Available The prospect of a device that uses solar energy to split water into H2 and O2 is highly attractive in terms of producing hydrogen as a carbon-neutral fuel. In this mini review, key research milestones that have been reached in this field over the last two decades will be discussed, with special focus on devices that use earth-abundant materials. Finally, the remaining challenges in the development of such “artificial leaves” will be highlighted.

  3. Leprosy: ancient disease remains a public health problem nowadays.

    Science.gov (United States)

    Noriega, Leandro Fonseca; Chiacchio, Nilton Di; Noriega, Angélica Fonseca; Pereira, Gilmayara Alves Abreu Maciel; Vieira, Marina Lino

    2016-01-01

    Despite being an ancient disease, leprosy remains a public health problem in several countries -particularly in India, Brazil and Indonesia. The current operational guidelines emphasize the evaluation of disability from the time of diagnosis and stipulate as fundamental principles for disease control: early detection and proper treatment. Continued efforts are needed to establish and improve quality leprosy services. A qualified primary care network that is integrated into specialized service and the development of educational activities are part of the arsenal in the fight against the disease, considered neglected and stigmatizing.

  4. Studies on protozoa in ancient remains - A Review

    Directory of Open Access Journals (Sweden)

    Liesbeth Frías

    2013-02-01

    Full Text Available Paleoparasitological research has made important contributions to the understanding of parasite evolution and ecology. Although parasitic protozoa exhibit a worldwide distribution, recovering these organisms from an archaeological context is still exceptional and relies on the availability and distribution of evidence, the ecology of infectious diseases and adequate detection techniques. Here, we present a review of the findings related to protozoa in ancient remains, with an emphasis on their geographical distribution in the past and the methodologies used for their retrieval. The development of more sensitive detection methods has increased the number of identified parasitic species, promising interesting insights from research in the future.

  5. Encephalitozoon cuniculi in Raw Cow's Milk Remains Infectious After Pasteurization.

    Science.gov (United States)

    Kváč, Martin; Tomanová, Vendula; Samková, Eva; Koubová, Jana; Kotková, Michaela; Hlásková, Lenka; McEvoy, John; Sak, Bohumil

    2016-02-01

    This study describes the prevalence of Encephalitozoon cuniculi in raw cow's milk and evaluates the effect of different milk pasteurization treatments on E. cuniculi infectivity for severe combined immunodeficient (SCID) mice. Using a nested polymerase chain reaction approach, 1 of 50 milking cows was found to repeatedly shed E. cuniculi in its feces and milk. Under experimental conditions, E. cuniculi spores in milk remained infective for SCID mice following pasteurization treatments at 72 °C for 15 s or 85 °C for 5 s. Based on these findings, pasteurized cow's milk should be considered a potential source of E. cuniculi infection in humans.

  6. "Recent" macrofossil remains from the Lomonosov Ridge, central Arctic Ocean

    Science.gov (United States)

    Le Duc, Cynthia; de Vernal, Anne; Archambault, Philippe; Brice, Camille; Roberge, Philippe

    2016-04-01

    The examination of surface sediment samples collected from 17 sites along the Lomonosov Ridge at water depths ranging from 737 to 3339 meters during Polarstern Expedition PS87 in 2014 (Stein, 2015), indicates a rich biogenic content almost exclusively dominated by calcareous remains. Amongst biogenic remains, microfossils (planktic and benthic foraminifers, pteropods, ostracods, etc.) dominate but millimetric to centrimetric macrofossils occurred frequently at the surface of the sediment. The macrofossil remains consist of a large variety of taxa, including gastropods, bivalvia, polychaete tubes, scaphopods, echinoderm plates and spines, and fish otoliths. Among the Bivalvia, the most abundant taxa are Portlandia arctica, Hyalopecten frigidus, Cuspidaria glacilis, Policordia densicostata, Bathyarca spp., and Yoldiella spp. Whereas a few specimens are well preserved and apparently pristine, most mollusk shells displayed extensive alteration features. Moreover, most shells were covered by millimeter scale tubes of the serpulid polychaete Spirorbis sp. suggesting transport from low intertidal or subtidal zone. Both the ecological affinity and known geographic distribution of identified bivalvia as named above support the hypothesis of transportation rather than local development. In addition to mollusk shells, more than a hundred fish otoliths were recovered in surface sediments. The otoliths mostly belong to the Gadidae family. Most of them are well preserved and without serpulid tubes attached to their surface, suggesting a local/regional origin, unlike the shell remains. Although recovered at the surface, the macrofaunal assemblages of the Lomonosov Ridge do not necessarily represent the "modern" environments as they may result from reworking and because their occurrence at the surface of the sediment may also be due to winnowing of finer particles. Although the shells were not dated, we suspect that their actual ages may range from modern to several thousands of

  7. Limit loads in nozzles

    International Nuclear Information System (INIS)

    Zouain, N.

    1983-01-01

    The static method for the evaluation of the limit loads of a perfectly elasto-plastic structure is presented. Using the static theorem of Limit Analysis and the Finite Element Method, a lower bound for the colapso load can be obtained through a linear programming problem. This formulation if then applied to symmetrically loaded shells of revolution and some numerical results of limit loads in nozzles are also presented. (Author) [pt

  8. Thermal effects of condensing water have remained local

    International Nuclear Information System (INIS)

    Ilus, E.

    1997-01-01

    General eutrophication of the Gulf of Finland has played a major role in the biological changes that have taken place in the sea area off Loviisa nuclear power plant. The quantities of plant nutrients in the water are now 1.5 to 2 times greater than 20 years ago. Changes attributable to the thermal effects of the power plant's cooling waters have been relatively small, and they have been restricted to the immediate surroundings of the discharge area. The most distinct environmental effects have been discovered in the temperatures of sea water, in ice conditions and in water currents within the discharge area of cooling water. The most visible biological change that has a direct link to the thermal load resulting from the power plant is the more abundant aquatic flora near the discharge point of cooling water on the southwestern shores of the Haestholmsfjaerden. Similar growth of aquatic flora has also been discovered near the discharge outlet of Olkiluoto plant, although the nutrient contents of water there are only half of the values measured in the Loviisa area. Regular radiation monitoring of the areas surrounding the nuclear power plants began before the start up of the plants. The contents of radioactive substances discovered have been small and in agreement with the release data given by the power companies. (orig.)

  9. Fossil human remains from Bolomor Cave (Valencia, Spain).

    Science.gov (United States)

    Arsuaga, Juan Luis; Fernández Peris, Josep; Gracia-Téllez, Ana; Quam, Rolf; Carretero, José Miguel; Barciela González, Virginia; Blasco, Ruth; Cuartero, Felipe; Sañudo, Pablo

    2012-05-01

    Systematic excavations carried out since 1989 at Bolomor Cave have led to the recovery of four Pleistocene human fossil remains, consisting of a fibular fragment, two isolated teeth, and a nearly complete adult parietal bone. All of these specimens date to the late Middle and early Late Pleistocene (MIS 7-5e). The fibular fragment shows thick cortical bone, an archaic feature found in non-modern (i.e. non-Homo sapiens) members of the genus Homo. Among the dental remains, the lack of a midtrigonid crest in the M(1) represents a departure from the morphology reported for the majority of Neandertal specimens, while the large dimensions and pronounced shoveling of the marginal ridges in the C(1) are similar to other European Middle and late Pleistocene fossils. The parietal bone is very thick, with dimensions that generally fall above Neandertal fossils and resemble more closely the Middle Pleistocene Atapuerca (SH) adult specimens. Based on the presence of archaic features, all the fossils from Bolomor are attributed to the Neandertal evolutionary lineage. Copyright © 2012 Elsevier Ltd. All rights reserved.

  10. Determination of Remaining Useful Life of Gas Turbine Blade

    Directory of Open Access Journals (Sweden)

    Meor Said Mior Azman

    2016-01-01

    Full Text Available The aim of this research is to determine the remaining useful life of gas turbine blade, using service-exposed turbine blades. This task is performed using Stress Rupture Test (SRT under accelerated test conditions where the applied stresses to the specimen is between 400 MPa to 600 MPa and the test temperature is 850°C. The study will focus on the creep behaviour of the 52000 hours service-exposed blades, complemented with creep-rupture modelling using JMatPro software and microstructure examination using optical microscope. The test specimens, made up of Ni-based superalloy of the first stage turbine blades, are machined based on International Standard (ISO 24. The results from the SRT will be analyzed using these two main equations – Larson-Miller Parameter and Life Fraction Rule. Based on the results of the remaining useful life analysis, the 52000h service-exposed blade has the condition to operate in the range of another 4751 hr to 18362 hr. The microstructure examinations shows traces of carbide precipitation that deteriorate the grain boundaries that occurs during creep process. Creep-rupture life modelling using JMatPro software has shown good agreement with the accelerated creep rupture test with minimal error.

  11. A method for defleshing human remains using household bleach.

    Science.gov (United States)

    Mann, Robert W; Berryman, Hugh E

    2012-03-01

    Medical examiners and forensic anthropologists are often faced with the difficult task of removing soft tissue from the human skeleton without damaging the bones, teeth and, in some cases, cartilage. While there are a number of acceptable methods that can be used to remove soft tissue including macerating in water, simmering or boiling, soaking in ammonia, removing with scissors, knife, scalpel or stiff brush, and dermestid beetles, each has its drawback in time, safety, or potential to damage bone. This technical report using the chest plate of a stabbing victim presents a safe and effective alternative method for removing soft tissue from human remains, in particular the chest plate, following autopsy, without damaging or separating the ribs, sternum, and costal cartilage. This method can be used to reveal subtle blunt force trauma to bone, slicing and stabbing injuries, and other forms of trauma obscured by overlying soft tissue. Despite the published cautionary notes, when done properly household bleach (3-6% sodium hypochlorite) is a quick, safe, and effective method for examining cartilage and exposing skeletal trauma by removing soft tissue from human skeletal remains. 2011 American Academy of Forensic Sciences. Published 2011. This article is a U.S. Government work and is in the public domain in the U.S.A.

  12. Duplex Alu Screening for Degraded DNA of Skeletal Human Remains

    Directory of Open Access Journals (Sweden)

    Fabian Haß

    2017-10-01

    Full Text Available The human-specific Alu elements, belonging to the class of Short INterspersed Elements (SINEs, have been shown to be a powerful tool for population genetic studies. An earlier study in this department showed that it was possible to analyze Alu presence/absence in 3000-year-old skeletal human remains from the Bronze Age Lichtenstein cave in Lower Saxony, Germany. We developed duplex Alu screening PCRs with flanking primers for two Alu elements, each combined with a single internal Alu primer. By adding an internal primer, the approximately 400–500 bp presence signals of Alu elements can be detected within a range of less than 200 bp. Thus, our PCR approach is suited for highly fragmented ancient DNA samples, whereas NGS analyses frequently are unable to handle repetitive elements. With this analysis system, we examined remains of 12 individuals from the Lichtenstein cave with different degrees of DNA degradation. The duplex PCRs showed fully informative amplification results for all of the chosen Alu loci in eight of the 12 samples. Our analysis system showed that Alu presence/absence analysis is possible in samples with different degrees of DNA degradation and it reduces the amount of valuable skeletal material needed by a factor of four, as compared with a singleplex approach.

  13. Run-of-River Impoundments Can Remain Unfilled While Transporting Gravel Bedload: Numerical Modeling Results

    Science.gov (United States)

    Pearson, A.; Pizzuto, J. E.

    2015-12-01

    Previous work at run-of-river (ROR) dams in northern Delaware has shown that bedload supplied to ROR impoundments can be transported over the dam when impoundments remain unfilled. Transport is facilitated by high levels of sand in the impoundment that lowers the critical shear stresses for particle entrainment, and an inversely sloping sediment ramp connecting the impoundment bed (where the water depth is typically equal to the dam height) with the top of the dam (Pearson and Pizzuto, in press). We demonstrate with one-dimensional bed material transport modeling that bed material can move through impoundments and that equilibrium transport (i.e., a balance between supply to and export from the impoundment, with a constant bed elevation) is possible even when the bed elevation is below the top of the dam. Based on our field work and previous HEC-RAS modeling, we assess bed material transport capacity at the base of the sediment ramp (and ignore detailed processes carrying sediment up and ramp and over the dam). The hydraulics at the base of the ramp are computed using a weir equation, providing estimates of water depth, velocity, and friction, based on the discharge and sediment grain size distribution of the impoundment. Bedload transport rates are computed using the Wilcock-Crowe equation, and changes in the impoundment's bed elevation are determined by sediment continuity. Our results indicate that impoundments pass the gravel supplied from upstream with deep pools when gravel supply rate is low, gravel grain sizes are relatively small, sand supply is high, and discharge is high. Conversely, impoundments will tend to fill their pools when gravel supply rate is high, gravel grain sizes are relatively large, sand supply is low, and discharge is low. The rate of bedload supplied to an impoundment is the primary control on how fast equilibrium transport is reached, with discharge having almost no influence on the timing of equilibrium.

  14. Highly efficient DNA extraction method from skeletal remains

    Directory of Open Access Journals (Sweden)

    Irena Zupanič Pajnič

    2011-03-01

    Full Text Available Background: This paper precisely describes the method of DNA extraction developed to acquire high quality DNA from the Second World War skeletal remains. The same method is also used for molecular genetic identification of unknown decomposed bodies in routine forensic casework where only bones and teeth are suitable for DNA typing. We analysed 109 bones and two teeth from WWII mass graves in Slovenia. Methods: We cleaned the bones and teeth, removed surface contaminants and ground the bones into powder, using liquid nitrogen . Prior to isolating the DNA in parallel using the BioRobot EZ1 (Qiagen, the powder was decalcified for three days. The nuclear DNA of the samples were quantified by real-time PCR method. We acquired autosomal genetic profiles and Y-chromosome haplotypes of the bones and teeth with PCR amplification of microsatellites, and mtDNA haplotypes 99. For the purpose of traceability in the event of contamination, we prepared elimination data bases including genetic profiles of the nuclear and mtDNA of all persons who have been in touch with the skeletal remains in any way. Results: We extracted up to 55 ng DNA/g of the teeth, up to 100 ng DNA/g of the femurs, up to 30 ng DNA/g of the tibias and up to 0.5 ng DNA/g of the humerus. The typing of autosomal and YSTR loci was successful in all of the teeth, in 98 % dekalof the femurs, and in 75 % to 81 % of the tibias and humerus. The typing of mtDNA was successful in all of the teeth, and in 96 % to 98 % of the bones. Conclusions: We managed to obtain nuclear DNA for successful STR typing from skeletal remains that were over 60 years old . The method of DNA extraction described here has proved to be highly efficient. We obtained 0.8 to 100 ng DNA/g of teeth or bones and complete genetic profiles of autosomal DNA, Y-STR haplotypes, and mtDNA haplotypes from only 0.5g bone and teeth samples.

  15. Vessels for elevated temperature service

    International Nuclear Information System (INIS)

    O'Donnell, W.J.; Porowski, J.S.

    1983-01-01

    The subject is covered in chapters, entitled: introduction (background; elevated temperature concerns; design tools); design of pressure vessels for elevated temperature per ASME code; basic elevated temperature failure modes; allowable stresses and strains per ASME code (basic allowable stress limits; ASME code limits for bending; time-fraction summations; strain limits; buckling and instability; negligible creep and stress-rupture effects); combined membrane and bending stresses in creep regime; thermal stress cycles; bounding methods based on elastic core concept (bounds on accumulated strains; more accurate bounds; strain ranges; maximum stresses; strains at discontinuities); elastic follow-up; creep strain concentrations; time-dependent fatigue (combined creep rupture and fatigue damage; limits for inelastic design analyses; limits for elastic design analyses); flaw evaluation techniques; type 316 stainless steel; type 304 stainless steel; steel 2 1/4Cr1Mo; Inconel 718; Incolloy 800; Hastelloy X; detailed inelastic design analyses. (U.K.)

  16. TMI in perspective: reactor containment stands up, difficult decisions remain

    International Nuclear Information System (INIS)

    Corey, G.R.

    1979-01-01

    Commonwealth Edison Co. is increasing its commitment to nuclear energy after reviewing the performance of the Three Mile Island reactor containment systems. Both the reactor vessel and the secondary containment remained intact and no radiation was reported in the soil or water. The public discussion of energy options which followed the accident will benefit both the public and technical community even if there is a temporary slowdown in nuclear power development. The realities of energy supplies have become evident; i.e., that nuclear and coal are the only available options for the short-term. The discussion should also lead to better personnel training, regulatory reforms, risk-sharing insurance, and international standards. The public hysteria triggered by the accident stemmed partly from the combination of unfortunate incidents and the media coverage, which led to hasty conclusions

  17. Oldest Directly Dated Remains of Sheep in China

    Science.gov (United States)

    Dodson, John; Dodson, Eoin; Banati, Richard; Li, Xiaoqiang; Atahan, Pia; Hu, Songmei; Middleton, Ryan J.; Zhou, Xinying; Nan, Sun

    2014-11-01

    The origins of domesticated sheep (Ovis sp.) in China remain unknown. Previous workers have speculated that sheep may have been present in China up to 7000 years ago, however many claims are based on associations with archaeological material rather than independent dates on sheep material. Here we present 7 radiocarbon dates on sheep bone from Inner Mongolia, Ningxia and Shaanxi provinces. DNA analysis on one of the bones confirms it is Ovis sp. The oldest ages are about 4700 to 4400 BCE and are thus the oldest objectively dated Ovis material in eastern Asia. The graphitisised bone collagen had δ13C values indicating some millet was represented in the diet. This probably indicates sheep were in a domestic setting where millet was grown. The younger samples had δ13C values indicating that even more millet was in the diet, and this was likely related to changes in foddering practices

  18. On use of radial evanescence remain term in kinematic hardening

    International Nuclear Information System (INIS)

    Geyer, P.

    1995-01-01

    This paper presents the interest which lies in non-linear kinematic hardening rule with radial evanescence remain term as proposed for modelling multiaxial ratchetting. From analytical calculations in the case of the tension/torsion test, this ratchetting is compared with that proposed by Armstrong and Frederick. A modification is then proposed for Chaboche's elastoplastic model with two non-linear kinematic variables, by coupling the two types of hardening by means of two scalar parameters. Identification of these two parameters returns to speculate on the directions of strain in order to adjust the ratchetting to experimental observations. Using biaxial ratchetting tests on stainless steel 316 L specimens at ambient temperature, it is shown that satisfactory modelling of multiaxial ratchetting is obtained. (author). 4 refs., 5 figs

  19. Psychotherapy for Borderline Personality Disorder: Progress and Remaining Challenges.

    Science.gov (United States)

    Links, Paul S; Shah, Ravi; Eynan, Rahel

    2017-03-01

    The main purpose of this review was to critically evaluate the literature on psychotherapies for borderline personality disorder (BPD) published over the past 5 years to identify the progress with remaining challenges and to determine priority areas for future research. A systematic review of the literature over the last 5 years was undertaken. The review yielded 184 relevant abstracts, and after applying inclusion criteria, 16 articles were fully reviewed based on the articles' implications for future research and/or clinical practice. Our review indicated that patients with various severities benefited from psychotherapy; more intensive therapies were not significantly superior to less intensive therapies; enhancing emotion regulation processes and fostering more coherent self-identity were important mechanisms of change; therapies had been extended to patients with BPD and posttraumatic stress disorder; and more research was needed to be directed at functional outcomes.

  20. [Alcohol and work: remaining sober and return to work].

    Science.gov (United States)

    Vittadini, G; Bandirali, M

    2007-01-01

    One of the most complex alcohol-driven problems is the job loss and the subsequent attempts to return to a professional activity. In order to better understand the issue, an epidemiologic investigation was carried out on a group of 162 alcoholics whilst hospitalised in a specialised clinic. The outcome shows the importance of remaining sober to keep or to be returned to one's own job. Unfortunately, local resources at hand, first of all joining an auto-mutual-help group, re still too little known and thus clearly underemployed. Therefore, an informative action within companies is highly desirable. Those alcoholics suffering from serious illnesses, especially mental ones represent a different issue. For these people a higher involvement of public authorities is desirable in creating protected job openings.

  1. Differential Decomposition Among Pig, Rabbit, and Human Remains.

    Science.gov (United States)

    Dautartas, Angela; Kenyhercz, Michael W; Vidoli, Giovanna M; Meadows Jantz, Lee; Mundorff, Amy; Steadman, Dawnie Wolfe

    2018-03-30

    While nonhuman animal remains are often utilized in forensic research to develop methods to estimate the postmortem interval, systematic studies that directly validate animals as proxies for human decomposition are lacking. The current project compared decomposition rates among pigs, rabbits, and humans at the University of Tennessee's Anthropology Research Facility across three seasonal trials that spanned nearly 2 years. The Total Body Score (TBS) method was applied to quantify decomposition changes and calculate the postmortem interval (PMI) in accumulated degree days (ADD). Decomposition trajectories were analyzed by comparing the estimated and actual ADD for each seasonal trial and by fuzzy cluster analysis. The cluster analysis demonstrated that the rabbits formed one group while pigs and humans, although more similar to each other than either to rabbits, still showed important differences in decomposition patterns. The decomposition trends show that neither nonhuman model captured the pattern, rate, and variability of human decomposition. © 2018 American Academy of Forensic Sciences.

  2. Spatial electric load forecasting

    CERN Document Server

    Willis, H Lee

    2002-01-01

    Spatial Electric Load Forecasting Consumer Demand for Power and ReliabilityCoincidence and Load BehaviorLoad Curve and End-Use ModelingWeather and Electric LoadWeather Design Criteria and Forecast NormalizationSpatial Load Growth BehaviorSpatial Forecast Accuracy and Error MeasuresTrending MethodsSimulation Method: Basic ConceptsA Detailed Look at the Simulation MethodBasics of Computerized SimulationAnalytical Building Blocks for Spatial SimulationAdvanced Elements of Computerized SimulationHybrid Trending-Simulation MethodsAdvanced

  3. Cognitive Load and Cooperation

    DEFF Research Database (Denmark)

    Døssing, Felix Sebastian; Piovesan, Marco; Wengström, Erik Roland

    2017-01-01

    We study the effect of intuitive and reflective processes on cooperation using cognitive load. Compared with time constraint, which has been used in the previous literature, cognitive load is a more direct way to block reflective processes, and thus a more suitable way to study the link between...... intuition and cooperation. Using a repeated public goods game, we study the effect of different levels of cognitive load on contributions. We show that a higher cognitive load increases the initial level of cooperation. In particular, subjects are significantly less likely to fully free ride under high...... cognitive load....

  4. Premortal data in the process of skeletal remains identification

    Directory of Open Access Journals (Sweden)

    Marinković Nadica

    2012-01-01

    Full Text Available Background/Aim. The basic task of a forensic examiner during the exhumation of mass graves or in mass accidents is to establish identity of a person. The results obtained through these procedures depend on the level of perceptibility of post mortal changes and they are compared with premortal data obtained from family members of those missing or killed. Experience with exhumations has shown significant differences between the results obtained through exhumation and the premortal data. The aim of the study was to suggest the existance of the difference between premortal data and the results obtained by exhumation regarding the some parameters, as well as to direct premortal data colection to the specific skeletal forms. Methods. We performed comparative analysis of the results of exhumation of skeletal remains in a mass grave and the premortal data concerning the identified persons. The least number of individuals in this mass grave was calculated according to the upper parts of the right femur and it helped in calculating the smallest number of individuals in mass graves to be 48. A total of 27 persons were identified. Sex was determined by metrics and morphology of the pelvis. Personal age in the moment of death was determined by morphology features of groin symphisis and morphology of sternal edge of ribs and other parts of scelets observations. The hight was calculated as average results of length of long bones and Rollet coefficients. Results. There was a complete match in terms of sex and age matched within an interval that could be established based on the skeletal remains. All the other parameters were different, however, which made identification significantly more difficult. Conclusion. The premortal data is an important element of identification process and it should be obtained by the forensic doctor and directed towards more detailed examination of the skeletal system.

  5. Reidentification of avian embryonic remains from the cretaceous of mongolia.

    Science.gov (United States)

    Varricchio, David J; Balanoff, Amy M; Norell, Mark A

    2015-01-01

    Embryonic remains within a small (4.75 by 2.23 cm) egg from the Late Cretaceous, Mongolia are here re-described. High-resolution X-ray computed tomography (HRCT) was used to digitally prepare and describe the enclosed embryonic bones. The egg, IGM (Mongolian Institute for Geology, Ulaanbaatar) 100/2010, with a three-part shell microstructure, was originally assigned to Neoceratopsia implying extensive homoplasy among eggshell characters across Dinosauria. Re-examination finds the forelimb significantly longer than the hindlimbs, proportions suggesting an avian identification. Additional, postcranial apomorphies (strut-like coracoid, cranially located humeral condyles, olecranon fossa, slender radius relative to the ulna, trochanteric crest on the femur, and ulna longer than the humerus) identify the embryo as avian. Presence of a dorsal coracoid fossa and a craniocaudally compressed distal humerus with a strongly angled distal margin support a diagnosis of IGM 100/2010 as an enantiornithine. Re-identification eliminates the implied homoplasy of this tri-laminate eggshell structure, and instead associates enantiornithine birds with eggshell microstructure composed of a mammillary, squamatic, and external zones. Posture of the embryo follows that of other theropods with fore- and hindlimbs folded parallel to the vertebral column and the elbow pointing caudally just dorsal to the knees. The size of the egg and embryo of IGM 100/2010 is similar to the two other Mongolian enantiornithine eggs. Well-ossified skeletons, as in this specimen, characterize all known enantiornithine embryos suggesting precocial hatchlings, comparing closely to late stage embryos of modern precocial birds that are both flight- and run-capable upon hatching. Extensive ossification in enantiornithine embryos may contribute to their relatively abundant representation in the fossil record. Neoceratopsian eggs remain unrecognized in the fossil record.

  6. Reidentification of avian embryonic remains from the cretaceous of mongolia.

    Directory of Open Access Journals (Sweden)

    David J Varricchio

    Full Text Available Embryonic remains within a small (4.75 by 2.23 cm egg from the Late Cretaceous, Mongolia are here re-described. High-resolution X-ray computed tomography (HRCT was used to digitally prepare and describe the enclosed embryonic bones. The egg, IGM (Mongolian Institute for Geology, Ulaanbaatar 100/2010, with a three-part shell microstructure, was originally assigned to Neoceratopsia implying extensive homoplasy among eggshell characters across Dinosauria. Re-examination finds the forelimb significantly longer than the hindlimbs, proportions suggesting an avian identification. Additional, postcranial apomorphies (strut-like coracoid, cranially located humeral condyles, olecranon fossa, slender radius relative to the ulna, trochanteric crest on the femur, and ulna longer than the humerus identify the embryo as avian. Presence of a dorsal coracoid fossa and a craniocaudally compressed distal humerus with a strongly angled distal margin support a diagnosis of IGM 100/2010 as an enantiornithine. Re-identification eliminates the implied homoplasy of this tri-laminate eggshell structure, and instead associates enantiornithine birds with eggshell microstructure composed of a mammillary, squamatic, and external zones. Posture of the embryo follows that of other theropods with fore- and hindlimbs folded parallel to the vertebral column and the elbow pointing caudally just dorsal to the knees. The size of the egg and embryo of IGM 100/2010 is similar to the two other Mongolian enantiornithine eggs. Well-ossified skeletons, as in this specimen, characterize all known enantiornithine embryos suggesting precocial hatchlings, comparing closely to late stage embryos of modern precocial birds that are both flight- and run-capable upon hatching. Extensive ossification in enantiornithine embryos may contribute to their relatively abundant representation in the fossil record. Neoceratopsian eggs remain unrecognized in the fossil record.

  7. Perceptual load affects exogenous spatial orienting while working memory load does not.

    Science.gov (United States)

    Santangelo, Valerio; Finoia, Paola; Raffone, Antonino; Belardinelli, Marta Olivetti; Spence, Charles

    2008-01-01

    We examined whether or not increasing visual perceptual load or visual working memory (WM) load would affect the exogenous orienting of visuo-spatial attention, in order to assess whether or not exogenous orienting is genuinely automatic. In Experiment 1, we manipulated visual perceptual load by means of a central morphing shape that in some trials morphed into a particular target shape (a rectangle) that participants had to detect. In Experiment 2, the possibility that the presentation of any changing stimulus at fixation would eliminate exogenous orienting was ruled out, by presenting two alternating letters at fixation. In Experiment 3, we manipulated visual WM load by means of arrays consisting of three (low-load) or five (high-load) randomly located coloured squares. The participants had to remember these items in order to judge whether a cued square had been presented in the same or different colour at the end of each trial. In all the experiments, exogenous visuo-spatial attentional orienting was measured by means of an orthogonal spatial cuing task, in which the participants had to discriminate the elevation (up vs. down) of a visual target previously cued by a spatially nonpredictive visual cue. The results showed that increasing the perceptual load of the task eliminated the exogenous orienting of visuo-spatial attention. By contrast, increasing the WM load had no effect on spatial orienting. These results are discussed in terms of the light that they shed on claims regarding the automaticity of visuo-spatial exogenous orienting.

  8. Troponin elevation in subarachnoid hemorrhage

    Directory of Open Access Journals (Sweden)

    Ioannis N. Mavridis

    2015-03-01

    Full Text Available Troponin (tr elevation in aneurysmal subarachnoid hemorrhage (SAH patients is often difficult to be appropriately assessed by clinicians, causing even disagreements regarding its management between neurosurgeons and cardiologists. The purpose of this article was to review the literature regarding the clinical interpretation of tr elevation in SAH. We searched for articles in PubMed using the key words: “troponin elevation” and “subarachnoid hemorrhage”. All of them, as well as relative neurosurgical books, were used for this review. Some type of cardiovascular abnormality develops in most SAH patients. Neurogenic stunned myocardium is a frequent SAH complication, due to catecholamine surge which induces cardiac injury, as evidenced by increased serum tr levels, electrocardiographic (ECG changes and cardiac wall motion abnormalities. Tr elevation, usually modest, is an early and specific marker for cardiac involvement after SAH and its levels peak about two days after SAH. Cardiac tr elevation predictors include poor clinical grade, intraventricular hemorrhage, loss of consciousness at ictus, global cerebral edema, female sex, large body surface area, lower systolic blood pressure, higher heart rate and prolonged Q-Tc interval. Elevated tr levels are associated with disability and death (especially tr >1 μg/L, worse neurological grade, systolic and diastolic cardiac dysfunction, pulmonary congestion, longer intensive care unit stay and incidence of vasospasm. Tr elevation is a common finding in SAH patients and constitutes a rightful cause of worry about the patients' cardiac function and prognosis. It should be therefore early detected, carefully monitored and appropriately managed by clinicians.

  9. Historie i spillefilm - for elever

    DEFF Research Database (Denmark)

    Tønnesen, Lone Guldbrandt

    2016-01-01

    MOOC om historiebrug i spillefilm, hvor elever kan lære om, hvordan spillefilm bruger fortiden, og om hvordan vores opfattelse af historien både sætter sig spor i filmene og bliver påvirket af dem.......MOOC om historiebrug i spillefilm, hvor elever kan lære om, hvordan spillefilm bruger fortiden, og om hvordan vores opfattelse af historien både sætter sig spor i filmene og bliver påvirket af dem....

  10. Tether Elevator Crawler Systems (TECS)

    Science.gov (United States)

    Swenson, Frank R.

    1987-01-01

    One of the needs of the experimenters on the space station is access to steady and controlled-variation microgravity environments. A method of providing these environments is to place the experiment on a tether attached to the space station. This provides a high degree of isolation from structural oscillations and vibrations. Crawlers can move these experiments along the tethers to preferred locations, much like an elevator. This report describes the motion control laws developed for these crawlers and the testing of laboratory models of these tether elevator crawlers.

  11. Ferritin Elevation and Improved Responsiveness to Erythropoiesis-Stimulating Agents in Patients on Ferric Citrate Hydrate

    Directory of Open Access Journals (Sweden)

    Keitaro Yokoyama

    2017-05-01

    Discussion: It is suggested that not only iron load but also the erythropoiesis-stimulating agent dose reduction may be involved in ferritin elevation during ferric citrate hydrate treatment, resulting in a decrease of erythropoietin resistance index.

  12. Characterization of salinity loads and selenium loads in the Smith Fork Creek region of the Lower Gunnison River Basin, western Colorado, 2008-2009

    Science.gov (United States)

    Richards, Rodney J.; Linard, Joshua I.; Hobza, Christopher M.

    2014-01-01

    The lower Gunnison River Basin of the Colorado River Basin has elevated salinity and selenium levels. The Colorado River Basin Salinity Control Act of June 24, 1974 (Public Law 93–320, amended by Public Law 98–569), authorized investigation of the Lower Gunnison Basin Unit Salinity Control Project by the U.S. Department of the Interior. The Bureau of Reclamation (Reclamation) and the Natural Resources Conservation Service are responsible for assessing and implementing measures to reduce salinity and selenium loading in the Colorado River Basin. Cost-sharing programs help farmers, ranchers, and canal companies improve the efficiency of water delivery systems and irrigation practices. The delivery systems (irrigation canals) have been identified as potential sources of seepage, which can contribute to salinity loading. Reclamation wants to identify seepage from irrigation systems in order to maximize the effectiveness of the various salinity-control methods, such as polyacrylamide lining and piping of irrigation canals programs. The U.S. Geological Survey, in cooperation with Reclamation, developed a study to characterize the salinity and selenium loading of seven subbasins in the Smith Fork Creek region and identify where control efforts can be maximized to reduce salinity and selenium loading. Total salinity loads ranged from 27.9±19.1 tons per year (t/yr) to 87,500±80,500 t/yr. The four natural subbasins—BkKm, RCG1, RCG2, and SF1—had total salinity loads of 27.9±19.1 t/yr, 371±248 t/yr, 2,180±1,590 t/yr, and 4,200±2,720 t/yr, respectively. The agriculturally influenced sites had salinity loads that ranged from 7,580±6,900 t/yr to 87,500±80,500 t/yr. Salinity loads for the subbasins AL1, B1, CK1, SF2, and SF3 were 7,580±6,900 t/yr; 28,300±26,700 t/yr; 48,700±36,100 t/yr; 87,500±80,900 t/yr; and 52,200±31,800 t/yr, respectively. The agricultural salinity load was separated into three components: tail water, deep percolation, and canal seepage

  13. Future Remains: Industrial Heritage at the Hanford Plutonium Works

    Science.gov (United States)

    Freer, Brian

    This dissertation argues that U.S. environmental and historic preservation regulations, industrial heritage projects, history, and art only provide partial frameworks for successfully transmitting an informed story into the long range future about nuclear technology and its related environmental legacy. This argument is important because plutonium from nuclear weapons production is toxic to humans in very small amounts, threatens environmental health, has a half-life of 24, 110 years and because the industrial heritage project at Hanford is the first time an entire U.S. Department of Energy weapons production site has been designated a U.S. Historic District. This research is situated within anthropological interest in industrial heritage studies, environmental anthropology, applied visual anthropology, as well as wider discourses on nuclear studies. However, none of these disciplines is really designed or intended to be a completely satisfactory frame of reference for addressing this perplexing challenge of documenting and conveying an informed story about nuclear technology and its related environmental legacy into the long range future. Others have thought about this question and have made important contributions toward a potential solution. Examples here include: future generations movements concerning intergenerational equity as evidenced in scholarship, law, and amongst Native American groups; Nez Perce and Confederated Tribes of the Umatilla Indian Reservation responses to the Hanford End State Vision and Hanford's Canyon Disposition Initiative; as well as the findings of organizational scholars on the advantages realized by organizations that have a long term future perspective. While these ideas inform the main line inquiry of this dissertation, the principal approach put forth by the researcher of how to convey an informed story about nuclear technology and waste into the long range future is implementation of the proposed Future Remains clause, as

  14. New Evidence Links Stellar Remains to Oldest Recorded Supernova

    Science.gov (United States)

    2006-09-01

    Recent observations have uncovered evidence that helps to confirm the identification of the remains of one of the earliest stellar explosions recorded by humans. The new study shows that the supernova remnant RCW 86 is much younger than previously thought. As such, the formation of the remnant appears to coincide with a supernova observed by Chinese astronomers in 185 A.D. The study used data from NASA's Chandra X-ray Observatory and the European Space Agency's XMM-Newton Observatory, "There have been previous suggestions that RCW 86 is the remains of the supernova from 185 A.D.," said Jacco Vink of University of Utrecht, the Netherlands, and lead author of the study. "These new X-ray data greatly strengthen the case." When a massive star runs out of fuel, it collapses on itself, creating a supernova that can outshine an entire galaxy. The intense explosion hurls the outer layers of the star into space and produces powerful shock waves. The remains of the star and the material it encounters are heated to millions of degrees and can emit intense X-ray radiation for thousands of years. Animation of a Massive Star Explosion Animation of a Massive Star Explosion In their stellar forensic work, Vink and colleagues studied the debris in RCW 86 to estimate when its progenitor star originally exploded. They calculated how quickly the shocked, or energized, shell is moving in RCW 86, by studying one part of the remnant. They combined this expansion velocity with the size of the remnant and a basic understanding of how supernovas expand to estimate the age of RCW 86. "Our new calculations tell us the remnant is about 2,000 years old," said Aya Bamba, a coauthor from the Institute of Physical and Chemical Research (RIKEN), Japan. "Previously astronomers had estimated an age of 10,000 years." The younger age for RCW 86 may explain an astronomical event observed almost 2000 years ago. In 185 AD, Chinese astronomers (and possibly the Romans) recorded the appearance of a new

  15. Spot market activity remains weak as prices continue to fall

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    A summary of financial data for the uranium spot market in November 1996 is provided. Price ranges for the restricted and unrestricted markets, conversion, and separative work are listed, and total market volume and new contracts are noted. Transactions made are briefly described. Deals made and pending in the spot concentrates, medium and long-term, conversion, and markets are listed for U.S. and non-U.S. buyers. Spot market activity increased in November with just over 1.0 million lbs of U3O8 equivalent being transacted compared to October's total of 530,000 lbs of U3O8 equivalent. The restricted uranium spot market price range slipped from $15.50-$15.70/lb U3O8 last month to $14.85/lb - $15.25/lb U3O8 this month. The unrestricted uranium spot market price range also slipped to $14.85/lb - $15.00/lb this month from $15.00/lb - $15.45/lb in October. Spot prices for conversion and separative work units remained at their October levels

  16. Briquettes of plant remains from the greenhouses of Almeria (Spain)

    Energy Technology Data Exchange (ETDEWEB)

    Callejon-Ferre, A. J.; Lopez-Martinez, J. A.

    2009-07-01

    Since ancient times, plant biomass has been used as a primary fuel, and today, with the impending depletion of fossil fuels, these vegetal sources constitute a cleaner alternative and furthermore have a multitude of uses. The aim of the present study is to design a method of recycling and reuse of plant wastes from intensive agriculture under plastic, by manufacturing briquettes in an environmentally friendly manner. In Almeria (SE Spain), agriculture generates 769,500 t year{sup -}1 of plant remains from greenhouse-grown horticultural crops, a resource currently used for composting and for producing electricity.With the machinery and procedures of the present study, another potential use has been developed by detoxifying and eliminating the plastic wastes of the original biomass for the fabrication of briquettes for fireplaces. The results were slightly inferior to the commercial briquette from other non-horticultural plant materials (no forestry material), specifically 2512 kJ kg{sup -}1, in the least favourable case. On the contrary, the heating value with respect to the two charcoals was significantly lower, with a difference of 12,142 kJ kg{sup -}1. In conclusion; a procedure, applicable in ecological cultivation without agrochemicals or plastic cords, has been developed and tested to reuse and transform plant materials from intensive cultivation into a stable non-toxic product similar to composite logs, applicable in commercial settings or in residential fireplaces. (Author) 48 refs.

  17. Are the alleged remains of Johann Sebastian Bach authentic?

    Science.gov (United States)

    Zegers, Richard H C; Maas, Mario; Koopman, A Ton G; Maat, George J R

    2009-02-16

    A skeleton alleged to be that of Johann Sebastian Bach (1685-1750) was exhumed from a graveyard in Leipzig, Germany, in 1894, but its authenticity is not established. In 1895, anatomist Wilhelm His concluded from his examination of the skeleton and reconstruction of the face that it most likely belonged to Bach. In 1949, surgeon Wolfgang Rosenthal noticed exostoses on the skeleton and on x-rays of 11 living organists and proposed a condition, Organistenkrankheit, which he interpreted as evidence that the skeleton was Bach's. However, our critical assessment of the remains analysis raises doubts: the localisation of the grave was dubious, and the methods used by His to reconstruct the face are controversial. Also, our study of the pelvic x-rays of 12 living professional organists failed to find evidence for the existence of Organistenkrankheit. We believe it is unlikely that the skeleton is that of Bach; techniques such as DNA analysis might help resolve the question but, to date, church authorities have not approved their use on the skeleton.

  18. Factors influencing home care nurse intention to remain employed.

    Science.gov (United States)

    Tourangeau, Ann; Patterson, Erin; Rowe, Alissa; Saari, Margaret; Thomson, Heather; MacDonald, Geraldine; Cranley, Lisa; Squires, Mae

    2014-11-01

    To identify factors affecting Canadian home care nurse intention to remain employed (ITR). In developed nations, healthcare continues to shift into community settings. Although considerable research exists on examining nurse ITR in hospitals, similar research related to nurses employed in home care is limited. In the face of a global nursing shortage, it is important to understand the factors influencing nurse ITR across healthcare sectors. A qualitative exploratory descriptive design was used. Focus groups were conducted with home care nurses. Data were analysed using qualitative content analysis. Six categories of influencing factors were identified by home care nurses as affecting ITR: job characteristics; work structures; relationships/communication; work environment; nurse responses to work; and employment conditions. Findings suggest the following factors influence home care nurse ITR: having autonomy; flexible scheduling; reasonable and varied workloads; supportive work relationships; and receiving adequate pay and benefits. Home care nurses did not identify job satisfaction as a single concept influencing ITR. Home care nursing management should support nurse autonomy, allow flexible scheduling, promote reasonable workloads and create opportunities for team building that strengthen supportive relationships among home care nurses and other health team members. © 2013 John Wiley & Sons Ltd.

  19. Carnivoran remains from the Malapa hominin site, South Africa.

    Directory of Open Access Journals (Sweden)

    Brian F Kuhn

    Full Text Available Recent discoveries at the new hominin-bearing deposits of Malapa, South Africa, have yielded a rich faunal assemblage associated with the newly described hominin taxon Australopithecus sediba. Dating of this deposit using U-Pb and palaeomagnetic methods has provided an age of 1.977 Ma, being one of the most accurately dated, time constrained deposits in the Plio-Pleistocene of southern Africa. To date, 81 carnivoran specimens have been identified at this site including members of the families Canidae, Viverridae, Herpestidae, Hyaenidae and Felidae. Of note is the presence of the extinct taxon Dinofelis cf. D. barlowi that may represent the last appearance date for this species. Extant large carnivores are represented by specimens of leopard (Panthera pardus and brown hyaena (Parahyaena brunnea. Smaller carnivores are also represented, and include the genera Atilax and Genetta, as well as Vulpes cf. V. chama. Malapa may also represent the first appearance date for Felis nigripes (Black-footed cat. The geochronological age of Malapa and the associated hominin taxa and carnivoran remains provide a window of research into mammalian evolution during a relatively unknown period in South Africa and elsewhere. In particular, the fauna represented at Malapa has the potential to elucidate aspects of the evolution of Dinofelis and may help resolve competing hypotheses about faunal exchange between East and Southern Africa during the late Pliocene or early Pleistocene.

  20. DNA Profiling Success Rates from Degraded Skeletal Remains in Guatemala.

    Science.gov (United States)

    Johnston, Emma; Stephenson, Mishel

    2016-07-01

    No data are available regarding the success of DNA Short Tandem Repeat (STR) profiling from degraded skeletal remains in Guatemala. Therefore, DNA profiling success rates relating to 2595 skeletons from eleven cases at the Forensic Anthropology Foundation of Guatemala (FAFG) are presented. The typical postmortem interval was 30 years. DNA was extracted from bone powder and amplified using Identifiler and Minifler. DNA profiling success rates differed between cases, ranging from 50.8% to 7.0%, the overall success rate for samples was 36.3%. The best DNA profiling success rates were obtained from femur (36.2%) and tooth (33.7%) samples. DNA profiles were significantly better from lower body bones than upper body bones (p = <0.0001). Bone samples from males gave significantly better profiles than samples from females (p = <0.0001). These results are believed to be related to bone density. The findings are important for designing forensic DNA sampling strategies in future victim recovery investigations. © 2016 American Academy of Forensic Sciences.

  1. Using contractors to decommission while remaining as licensee

    International Nuclear Information System (INIS)

    Rankine, A.

    1997-01-01

    Over the last few years the role of the United Kingdom Atomic Energy Authority (UKAEA) has changed from one involved in research and development in the field of nuclear power and associated technology, to one of managing the liabilities left over from its previous mission. This period has also seen two significant portions of the organization move to the private sector with sale of the Facilities Services Division to PROCORD and the privatization of AEA Technology. The new UKAEA is therefore a focused liabilities management organization, making the best use of expertise in the private sector in carrying out its mission, but retaining adequate internal resource and expertise to fulful its role and responsibilities as the licensee. UKAEA continues to be committed to giving the highest priority to meeting high standards of safety and environmental protection required of the holder of the Nuclear Site Licence under the Nuclear Installations Act. This paper describes the safety management system within the UKAEA which ensures that UKAEA remains the proper and effective licensee and gives some examples of how this has worked in practice. (author)

  2. Dannelsen af den ansvarlige elev

    DEFF Research Database (Denmark)

    Larsen, Jesper

    2010-01-01

    Denne artikel handler om den del af lærergerningen, der har at gøre med udarbejdelse af elevplaner. Der tages udgangspunkt i en foucaultsk forståelse, hvor beskrivelsen af den enkelte elev udtrykker et særligt normativt ideal om, hvilke former for elevhed der er de ønskværdige i den danske...

  3. Methylphenidatinduceret ST-elevations-myokardieinfarkt

    DEFF Research Database (Denmark)

    Ruwald, Martin Huth; Ruwald, Anne-Christine Huth; Tønder, Niels

    2012-01-01

    Adult attention deficit and hyperkinetic disorder (ADHD) is increasingly diagnosed and treated with methylphenidate. We present the case of an 20 year-old man, who was diagnosed with ADHD and suffered a ST elevation acute myocardial infarction due to coronary vasospasm related to an overdose...

  4. Elevated lactate during psychogenic hyperventilation

    NARCIS (Netherlands)

    ter Avest, E.; Patist, F. M.; ter Maaten, J. C.; Nijsten, M. W. N.

    Study objective Elevated arterial lactate levels are closely related to morbidity and mortality in various patient categories. In the present retrospective study, the relation between arterial lactate, partial pressure of carbon dioxide (Pco(2)) and pH was systematically investigated in patients who

  5. Optimisation of load control

    International Nuclear Information System (INIS)

    Koponen, P.

    1998-01-01

    Electricity cannot be stored in large quantities. That is why the electricity supply and consumption are always almost equal in large power supply systems. If this balance were disturbed beyond stability, the system or a part of it would collapse until a new stable equilibrium is reached. The balance between supply and consumption is mainly maintained by controlling the power production, but also the electricity consumption or, in other words, the load is controlled. Controlling the load of the power supply system is important, if easily controllable power production capacity is limited. Temporary shortage of capacity causes high peaks in the energy price in the electricity market. Load control either reduces the electricity consumption during peak consumption and peak price or moves electricity consumption to some other time. The project Optimisation of Load Control is a part of the EDISON research program for distribution automation. The following areas were studied: Optimization of space heating and ventilation, when electricity price is time variable, load control model in power purchase optimization, optimization of direct load control sequences, interaction between load control optimization and power purchase optimization, literature on load control, optimization methods and field tests and response models of direct load control and the effects of the electricity market deregulation on load control. An overview of the main results is given in this chapter

  6. Optimisation of load control

    Energy Technology Data Exchange (ETDEWEB)

    Koponen, P [VTT Energy, Espoo (Finland)

    1998-08-01

    Electricity cannot be stored in large quantities. That is why the electricity supply and consumption are always almost equal in large power supply systems. If this balance were disturbed beyond stability, the system or a part of it would collapse until a new stable equilibrium is reached. The balance between supply and consumption is mainly maintained by controlling the power production, but also the electricity consumption or, in other words, the load is controlled. Controlling the load of the power supply system is important, if easily controllable power production capacity is limited. Temporary shortage of capacity causes high peaks in the energy price in the electricity market. Load control either reduces the electricity consumption during peak consumption and peak price or moves electricity consumption to some other time. The project Optimisation of Load Control is a part of the EDISON research program for distribution automation. The following areas were studied: Optimization of space heating and ventilation, when electricity price is time variable, load control model in power purchase optimization, optimization of direct load control sequences, interaction between load control optimization and power purchase optimization, literature on load control, optimization methods and field tests and response models of direct load control and the effects of the electricity market deregulation on load control. An overview of the main results is given in this chapter

  7. Simulation and analysis of the energy consumption of elevator systems; Simulation und Analyse des Energiebedarfs von Aufzugssystemen

    Energy Technology Data Exchange (ETDEWEB)

    Pletschen, Ingo; Rohr, Stephan [ThyssenKrupp Aufzugswerke GmbH, Neuhausen a.d.F. (Germany); Kennel, Ralph [Technische Univ. Muenchen (Germany)

    2011-07-01

    Elevator systems would be in principal a good example for a perpetuum mobile. While lifting loads and persons electrical energy is converted into potential energy and reconverted later. In practice these conversions are however lossy. So the aim for high energy efficiency is to minimize these losses. However, as a travel of an elevator consists in main parts of acceleration and deceleration, the exclusive consideration of the efficiency during constant speed is not sufficient. Thus a simulation environment is introduced which reliably determines the elevators' energy consumption. The simulation is validated at an elevator afterwards the different influences on the energy consumption of elevators are analyzed. (orig.)

  8. Optimal load scheduling in commercial and residential microgrids

    Science.gov (United States)

    Ganji Tanha, Mohammad Mahdi

    Residential and commercial electricity customers use more than two third of the total energy consumed in the United States, representing a significant resource of demand response. Price-based demand response, which is in response to changes in electricity prices, represents the adjustments in load through optimal load scheduling (OLS). In this study, an efficient model for OLS is developed for residential and commercial microgrids which include aggregated loads in single-units and communal loads. Single unit loads which include fixed, adjustable and shiftable loads are controllable by the unit occupants. Communal loads which include pool pumps, elevators and central heating/cooling systems are shared among the units. In order to optimally schedule residential and commercial loads, a community-based optimal load scheduling (CBOLS) is proposed in this thesis. The CBOLS schedule considers hourly market prices, occupants' comfort level, and microgrid operation constraints. The CBOLS' objective in residential and commercial microgrids is the constrained minimization of the total cost of supplying the aggregator load, defined as the microgrid load minus the microgrid generation. This problem is represented by a large-scale mixed-integer optimization for supplying single-unit and communal loads. The Lagrangian relaxation methodology is used to relax the linking communal load constraint and decompose the independent single-unit functions into subproblems which can be solved in parallel. The optimal solution is acceptable if the aggregator load limit and the duality gap are within the bounds. If any of the proposed criteria is not satisfied, the Lagrangian multiplier will be updated and a new optimal load schedule will be regenerated until both constraints are satisfied. The proposed method is applied to several case studies and the results are presented for the Galvin Center load on the 16th floor of the IIT Tower in Chicago.

  9. Elevated arousal levels enhance contrast perception.

    Science.gov (United States)

    Kim, Dongho; Lokey, Savannah; Ling, Sam

    2017-02-01

    Our state of arousal fluctuates from moment to moment-fluctuations that can have profound impacts on behavior. Arousal has been proposed to play a powerful, widespread role in the brain, influencing processes as far ranging as perception, memory, learning, and decision making. Although arousal clearly plays a critical role in modulating behavior, the mechanisms underlying this modulation remain poorly understood. To address this knowledge gap, we examined the modulatory role of arousal on one of the cornerstones of visual perception: contrast perception. Using a reward-driven paradigm to manipulate arousal state, we discovered that elevated arousal state substantially enhances visual sensitivity, incurring a multiplicative modulation of contrast response. Contrast defines vision, determining whether objects appear visible or invisible to us, and these results indicate that one of the consequences of decreased arousal state is an impaired ability to visually process our environment.

  10. Estimation the remaining service-lifetime of wooden structure of geothermal cooling tower

    Directory of Open Access Journals (Sweden)

    Effendi Tri Bahtiar

    2017-06-01

    Full Text Available Similar with other construction materials, wood strength is decreasing when applied by long term loading. Wooden cooling tower structure at Star Energy Geothermal (Wayang Windu Ltd was built in 1998 and it should be evaluated to avoid sudden structural failure. Evaluation conducted through several steps: wood species identification, the physical and mechanical properties testing, and estimation for remaining service-lifetime by generating mathematical models derived from creep test and reduction of cross sectional area of the wood. Identification result that the wood are redwood (Sequoia sempervirens and Douglas fir (Pseudotsuga menziesii. The wood density value has degraded from the surface until 0.25 cm depth. Strength characteristics of the wood have considerably decreased, but the allowable stress for bending, tension parallel to grain, and shear were still higher than NDS2005 requirements. The allowable stress for compression parallel to grain was slightly lower than NDS, while compression perpendicular to grain was much lower. Average modulus of elasticity reduces become lower than the value stated by the code, but the minimum value of modulus of elasticity (Emin of redwood was still higher than the code value, while Emin of Douglas fir is slightly lower. Then, in accordance with those findings, the construction would not failure yet but the deformation and vibration will occur in higher rate than design planning. This research develops mathematical models for estimating the remaining service-lifetime of the wooden cooling tower structure in geothermal power plant based on the wood performance in resisting long term loading and its deterioration rate. The deterioration rate of wood member of cooling tower structure at Star Energy Geothermal (Wayang Windu Ltd is 0.0147 cm depth per year, so equation for the residual service life estimation is σlaterσtoday=bh2(b−0.0147T(h−0.0147T2, and σlater must be lower than allowable stress.

  11. Mineralized remains of morphotypes of filamentous cyanobacteria in carbonaceous meteorites

    Science.gov (United States)

    Hoover, Richard B.

    2005-09-01

    rocks, living, cryopreserved and fossilized extremophiles and cyanobacteria. These studies have resulted in the detection of mineralized remains of morphotypes of filamentous cyanobacteria, mats and consortia in many carbonaceous meteorites. These well-preserved and embedded microfossils are consistent with the size, morphology and ultra-microstructure of filamentous trichomic prokaryotes and degraded remains of microfibrils of cyanobacterial sheaths. EDAX elemental studies reveal that the forms in the meteorites often have highly carbonized sheaths in close association with permineralized filaments, trichomes, and microbial cells. The eextensive protocols and methodologies that have been developed to protect the samples from contamination and to distinguish recent contaminants from indigenous microfossils are described recent bio-contaminants. Ratios of critical bioelements (C:O, C:N, C:P, and C:S) reveal dramatic differences between microfossils in Earth rocks and meteorites and in the cells, filaments, trichomes, and hormogonia of recently living cyanobacteria. The results of comparative optical, ESEM and FESEM studies and EDAX elemental analyses of recent cyanobacteria (e.g. Calothrix, Oscillatoria, and Lyngbya) of similar size, morphology and microstructure to microfossils found embedded in the Murchison CM2 and the Orgueil CI1 carbonaceous meteorites are presented

  12. Clarifying some remaining questions in the anomaly puzzle

    International Nuclear Information System (INIS)

    Huang, Xing; Parker, Leonard

    2011-01-01

    We discuss several points that may help to clarify some questions that remain about the anomaly puzzle in supersymmetric theories. In particular, we consider a general N=1 supersymmetric Yang-Mills theory. The anomaly puzzle concerns the question of whether there is a consistent way in the quantized theory to put the R-current and the stress tensor in a single supermultiplet called the supercurrent, even though in the classical theory they are in the same supermultiplet. It was proposed that the classically conserved supercurrent bifurcates into two supercurrents having different anomalies in the quantum regime. The most interesting result we obtain is an explicit expression for the lowest component of one of the two supercurrents in 4-dimensional spacetime, namely the supercurrent that has the energy-momentum tensor as one of its components. This expression for the lowest component is an energy-dependent linear combination of two chiral currents, which itself does not correspond to a classically conserved chiral current. The lowest component of the other supercurrent, namely, the R-current, satisfies the Adler-Bardeen theorem. The lowest component of the first supercurrent has an anomaly, which we show is consistent with the anomaly of the trace of the energy-momentum tensor. Therefore, we conclude that there is no consistent way to construct a single supercurrent multiplet that contains the R-current and the stress tensor in the straightforward way originally proposed. We also discuss and try to clarify some technical points in the derivations of the two supercurrents in the literature. These latter points concern the significance of infrared contributions to the NSVZ β-function and the role of the equations of motion in deriving the two supercurrents. (orig.)

  13. Will southern California remain a premium market for natural gas?

    International Nuclear Information System (INIS)

    John, F.E.

    1991-01-01

    Average yearly demand for natural gas in southern California totalled just over 3 billion ft 3 /d in 1991 and is projected to increase to just over 3.2 billion ft 3 /d in 2000 and 3.4 billion ft 3 /d in 2010. In the core residential market, demand is being driven by population growth and offset by conservation measures. In the core commercial and industrial market, demand is driven by employment growth and offset by conservation. In the noncore market, natural gas use is expected to fall from 262 million ft 3 /d in 1991 to 223 million ft 3 /d in 2010. Demand for natural gas for cogeneration is expected to either remain stagnant or decrease. The largest potential for market growth in southern California is for utility electric generation. Demand in this sector is expected to increase from 468 million ft 3 /d in 1991 to 1 billion ft 3 in 2010. Air quality concerns furnish a market opportunity for natural gas vehicles, and a substantial increase in natural gas demand might be obtained from even a modest market share of the region's 10 million vehicles. Existing pipeline capacity is sufficient to supply current average year requirements, and the need for new capacity hinges on the issues of satisfying high-year demand, meeting market growth, and accessing more desirable supply regions. Planned capacity additions of 2,150 million ft 3 /d, if completed, will bring substantial excess capacity to southern California in the late 1990s. The competitive advantages of various producing regions will then be greatly influenced by the rate designs used on the pipelines connecting them to the market. 4 tabs

  14. Neutron activation analysis of the prehistoric and ancient bone remains

    International Nuclear Information System (INIS)

    Vasidov, A.; Osinskaya, N.S.; Khatamov, Sh.; Rakhmanova, T.; Akhmadshaev, A.Sh.

    2006-01-01

    Full text: In the work results of the instrumental neutron activation analysis (INAA) of prehistoric bone remains of dinosaurs and ancient bones of bear, archantrop found out on the territory of Uzbekistan are presents. A bone of dinosaur from Mongolia, standard a bone of the person and soils taken from a surface and from of the femoral joint of a dinosaur were also subject to INAA. The INAA method determines of contents of about 30 elements in bones and soils in an interval 0.043-3600 mg / kg. Among found elements Ca (46 %), Sc, Cr, Fe (up to 2.2 g/kg), Ni, Zn, Sr (up to 3.6 g/kg), Sb, Ba, Sb and some others are mainly found in bones. The contents of some elements in bones of dinosaurs reach very high values 280-3200 mg / kg, and are mainly lanthanides La, Ce, Nd, Sm, Eu, Tb, Yb and Lu. In our opinion, lanthanides and some other elements, like As, Br, and Mo in bones were formed as a result of fission of uranium and transuranium elements. Because content of uranium in bones of dinosaurs is very high, up to 180 mg / kg, and those of thorium is 20 mg/ kg. However U and Th in soils are 4.8 mg/kg and 3.7 mg / kg, respectively. The content of uranium in bones of the archantrop is 1.53 mg / kg, while U in standard bone of the human is less than 0,016 mg/kg. (author)

  15. The broad spectrum revisited: evidence from plant remains.

    Science.gov (United States)

    Weiss, Ehud; Wetterstrom, Wilma; Nadel, Dani; Bar-Yosef, Ofer

    2004-06-29

    The beginning of agriculture is one of the most important developments in human history, with enormous consequences that paved the way for settled life and complex society. Much of the research on the origins of agriculture over the last 40 years has been guided by Flannery's [Flannery, K. V. (1969) in The Domestication and Exploitation of Plants and Animals, eds. Ucko, P. J. & Dimbleby, G. W. (Duckworth, London), pp. 73-100] "broad spectrum revolution" (BSR) hypothesis, which posits that the transition to farming in southwest Asia entailed a period during which foragers broadened their resource base to encompass a wide array of foods that were previously ignored in an attempt to overcome food shortages. Although these resources undoubtedly included plants, nearly all BSR hypothesis-inspired research has focused on animals because of a dearth of Upper Paleolithic archaeobotanical assemblages. Now, however, a collection of >90,000 plant remains, recently recovered from the Stone Age site Ohalo II (23,000 B.P.), Israel, offers insights into the plant foods of the late Upper Paleolithic. The staple foods of this assemblage were wild grasses, pushing back the dietary shift to grains some 10,000 years earlier than previously recognized. Besides the cereals (wild wheat and barley), small-grained grasses made up a large component of the assemblage, indicating that the BSR in the Levant was even broader than originally conceived, encompassing what would have been low-ranked plant foods. Over the next 15,000 years small-grained grasses were gradually replaced by the cereals and ultimately disappeared from the Levantine diet.

  16. RESEARCH OF INFLUENCING OF PROJECT DISCRIPTIONS OF ELEVATOR ON PARAMETERS OF ITS DRIVE

    Directory of Open Access Journals (Sweden)

    V. M. Bohomaz

    2015-02-01

    Full Text Available Purpose. One of basic elements of band bucket elevators is their drive. For determination of power drive it is necessary to conduct calculations on standard by methods, in what it is needed to expend enough time. One of project parameters is productivity of elevator. It is necessary to build parametric dependence of power drive of elevator on its design capacity that takes into account a type and descriptions of load, lifting height, standard sizes and parameters of buckets and tapes. Methodology. Using the method of hauling calculation of band buckets elevators, the parametric dependences of power drive of high-speed elevators are built with deep and shallow buckets from their productivity at fixed type of load and height of getting up. Findings. It is set on the basis of the built parametric dependences that the change function of a size of elevator power from design capacity (at fixed to the lifting height, load type, rate of tape movement is piecewise and droningly increasing. The intervals of project values of productivity, which provide the permanent size of elevator power drive are certain in a general view. As the example of application of the recived results the construction process of power drive dependence from design capacity of elevator of shotblasting room, which is intended for transporting of the metallic shot using for consolidating of carriage springs, is considered. For concrete type of load and lifting height of such elevator graphic dependence of power drive on productivity was built. Originality. Parametric dependences of elevator power drive on its design capacity were first built, which take into account a type and physical and mechanical descriptions of load, lifting height, standard sizes and parameters of buckets and tapes. Practical value. The use of the built dependences enables in relation to rapid determination of approximate value of power drive of vertical high-speed elevators with deep and shallow buckets on the

  17. Elevated placental adenosine signaling contributes to the pathogenesis of preeclampsia.

    Science.gov (United States)

    Iriyama, Takayuki; Sun, Kaiqi; Parchim, Nicholas F; Li, Jessica; Zhao, Cheng; Song, Anren; Hart, Laura A; Blackwell, Sean C; Sibai, Baha M; Chan, Lee-Nien L; Chan, Teh-Sheng; Hicks, M John; Blackburn, Michael R; Kellems, Rodney E; Xia, Yang

    2015-02-24

    Preeclampsia is a prevalent hypertensive disorder of pregnancy and a leading cause of maternal and neonatal morbidity and mortality worldwide. This pathogenic condition is speculated to be caused by placental abnormalities that contribute to the maternal syndrome. However, the specific factors and signaling pathways that lead to impaired placentas and maternal disease development remain elusive. Using 2 independent animal models of preeclampsia (genetically engineered pregnant mice with elevated adenosine exclusively in placentas and a pathogenic autoantibody-induced preeclampsia mouse model), we demonstrated that chronically elevated placental adenosine was sufficient to induce hallmark features of preeclampsia, including hypertension, proteinuria, small fetuses, and impaired placental vasculature. Genetic and pharmacological approaches revealed that elevated placental adenosine coupled with excessive A₂B adenosine receptor (ADORA2B) signaling contributed to the development of these features of preeclampsia. Mechanistically, we provided both human and mouse evidence that elevated placental CD73 is a key enzyme causing increased placental adenosine, thereby contributing to preeclampsia. We determined that elevated placental adenosine signaling is a previously unrecognized pathogenic factor for preeclampsia. Moreover, our findings revealed the molecular basis underlying the elevation of placental adenosine and the detrimental role of excess placental adenosine in the pathophysiology of preeclampsia, and thereby, we highlight novel therapeutic targets. © 2014 American Heart Association, Inc.

  18. Thermal barriers constrain microbial elevational range size via climate variability.

    Science.gov (United States)

    Wang, Jianjun; Soininen, Janne

    2017-08-01

    Range size is invariably limited and understanding range size variation is an important objective in ecology. However, microbial range size across geographical gradients remains understudied, especially on mountainsides. Here, the patterns of range size of stream microbes (i.e., bacteria and diatoms) and macroorganisms (i.e., macroinvertebrates) along elevational gradients in Asia and Europe were examined. In bacteria, elevational range size showed non-significant phylogenetic signals. In all taxa, there was a positive relationship between niche breadth and species elevational range size, driven by local environmental and climatic variables. No taxa followed the elevational Rapoport's rule. Climate variability explained the most variation in microbial mean elevational range size, whereas local environmental variables were more important for macroinvertebrates. Seasonal and annual climate variation showed negative effects, while daily climate variation had positive effects on community mean elevational range size for all taxa. The negative correlation between range size and species richness suggests that understanding the drivers of range is key for revealing the processes underlying diversity. The results advance the understanding of microbial species thermal barriers by revealing the importance of seasonal and diurnal climate variation, and highlight that aquatic and terrestrial biota may differ in their response to short- and long-term climate variability. © 2017 Society for Applied Microbiology and John Wiley & Sons Ltd.

  19. Seasonal Dynamics of Mobile Carbon Supply in Quercus aquifolioides at the Upper Elevational Limit

    Science.gov (United States)

    Zhu, Wan-Ze; Cao, Min; Wang, San-Gen; Xiao, Wen-Fan; Li, Mai-He

    2012-01-01

    Many studies have tried to explain the physiological mechanisms of the alpine treeline phenomenon, but the debate on the alpine treeline formation remains controversial due to opposite results from different studies. The present study explored the carbon-physiology of an alpine shrub species (Quercus aquifolioides) grown at its upper elevational limit compared to lower elevations, to test whether the elevational limit of alpine shrubs (treeline formation. PMID:22479567

  20. The Right to Remain Silent in Criminal Trial

    Directory of Open Access Journals (Sweden)

    Gianina Anemona Radu

    2013-05-01

    Full Text Available A person's right not to incriminate oneself or to remain silent and not contribute to their own incrimination is a basic requirement of due process, although the right not to testify against oneself is not expressly guaranteed. This legal right is intended to protect the accused/ the defendant against the authorities’ abusive coercion. The scope of the right not to incriminate oneself is related to criminal matter under the Convention, and thus susceptible or applicable to criminal proceedings concerning all types of crimes as a guarantee to a fair trial. The European Court of Justice ruled that despite the fact that art. 6 paragraph 2 of the Convention does not expressly mention the right not to incriminate oneself and the right not to contribute to their own incrimination (nemo tenetur are ipsum accusare these are generally recognized international rules that are in consistence with the notion of “fair trial” stipulated in art. 6. By virtue of the right to silence, the person charged with a crime is free to answer the questions or not, as he/she believes it is in his/her interest. Therefore, the right to silence involves not only the right not to testify against oneself, but also the right of the accused/ defendant not to incriminate oneself. Thus, the accused/defendant cannot be compelled to assist in the production of evidence and cannot be sanctioned for failing to provide certain documents or other evidence. Obligation to testify against personal will, under the constraint of a fine or any other form of coercion constitutes an interference with the negative aspect of the right to freedom of expression which must be necessary in a democratic society. It is essential to clarify certain issues as far as this right is concerned. First of all, the statutory provision in question is specific to adversarial systems, which are found mainly in Anglo-Saxon countries and are totally different from that underlying the current Romanian Criminal

  1. AIDS, individual behaviour and the unexplained remaining variation.

    Science.gov (United States)

    Katz, Alison

    2002-01-01

    From the start of the AIDS pandemic, individual behaviour has been put forward, implicitly or explicitly, as the main explanatory concept for understanding the epidemiology of HIV infection and in particular for the rapid spread and high prevalence in sub-Saharan Africa. This has had enormous implications for the international response to AIDS and has heavily influenced public health policy and strategy and the design of prevention and care interventions at national, community and individual level. It is argued that individual behaviour alone cannot possibly account for the enormous variation in HIV prevalence between population groups, countries and regions and that the unexplained remaining variation has been neglected by the international AIDS community. Biological vulnerability to HIV due to seriously deficient immune systems has been ignored as a determinant of the high levels of infection in certain populations. This is in sharp contrast to well proven public health approaches to other infectious diseases. In particular, it is argued that poor nutrition and co-infection with the myriad of other diseases of poverty including tuberculosis, malaria, leishmaniasis and parasitic infections, have been neglected as root causes of susceptibility, infectiousness and high rates of transmission of HIV at the level of populations. Vulnerability in terms of non-biological factors such as labour migration, prostitution, exchange of sex for survival, population movements due to war and violence, has received some attention but the solutions proposed to these problems are also inappropriately focused on individual behaviour and suffer from the same neglect of economic and political root causes. As the foundation for the international community's response to the AIDS pandemic, explanations of HIV/AIDS epidemiology in terms of individual behaviour are not only grossly inadequate, they are highly stigmatising and may in some cases, be racist. They have diverted attention from

  2. Concentrated loads on concrete

    DEFF Research Database (Denmark)

    Lorenzen, Karen Grøndahl; Nielsen, Mogens Peter

    1997-01-01

    This report deals with concentrated loads on concrete.A new upper bound solution in the axisymmetrical case of a point load in the center of the end face of a cylinder is developed.Based on previous work dealing with failure mechanisms and upper bound solutions, new approximate formulas are devel......This report deals with concentrated loads on concrete.A new upper bound solution in the axisymmetrical case of a point load in the center of the end face of a cylinder is developed.Based on previous work dealing with failure mechanisms and upper bound solutions, new approximate formulas...

  3. Critical Axial Load

    Directory of Open Access Journals (Sweden)

    Walt Wells

    2008-01-01

    Full Text Available Our objective in this paper is to solve a second order differential equation for a long, simply supported column member subjected to a lateral axial load using Heun's numerical method. We will use the solution to find the critical load at which the column member will fail due to buckling. We will calculate this load using Euler's derived analytical approach for an exact solution, as well as Euler's Numerical Method. We will then compare the three calculated values to see how much they deviate from one another. During the critical load calculation, it will be necessary to calculate the moment of inertia for the column member.

  4. Load regulating expansion fixture

    International Nuclear Information System (INIS)

    Wagner, L.M.; Strum, M.J.

    1998-01-01

    A free standing self contained device for bonding ultra thin metallic films, such as 0.001 inch beryllium foils is disclosed. The device will regulate to a predetermined load for solid state bonding when heated to a bonding temperature. The device includes a load regulating feature, whereby the expansion stresses generated for bonding are regulated and self adjusting. The load regulator comprises a pair of friction isolators with a plurality of annealed copper members located there between. The device, with the load regulator, will adjust to and maintain a stress level needed to successfully and economically complete a leak tight bond without damaging thin foils or other delicate components. 1 fig

  5. Laterally loaded masonry

    DEFF Research Database (Denmark)

    Raun Gottfredsen, F.

    In this thesis results from experiments on mortar joints and masonry as well as methods of calculation of strength and deformation of laterally loaded masonry are presented. The strength and deformation capacity of mortar joints have been determined from experiments involving a constant compressive...... stress and increasing shear. The results show a transition to pure friction as the cohesion is gradually destroyed. An interface model of a mortar joint that can take into account this aspect has been developed. Laterally loaded masonry panels have also been tested and it is found to be characteristic...... that laterally loaded masonry exhibits a non-linear load-displacement behaviour with some ductility....

  6. Electrical load modeling

    Energy Technology Data Exchange (ETDEWEB)

    Valgas, Helio Moreira; Pinto, Roberto del Giudice R.; Franca, Carlos [Companhia Energetica de Minas Gerais (CEMIG), Belo Horizonte, MG (Brazil); Lambert-Torres, Germano; Silva, Alexandre P. Alves da; Pires, Robson Celso; Costa, Junior, Roberto Affonso [Escola Federal de Engenharia de Itajuba, MG (Brazil)

    1994-12-31

    Accurate dynamic load models allow more precise calculations of power system controls and stability limits, which are critical mainly in the operation planning of power systems. This paper describes the development of a computer program (software) for static and dynamic load model studies using the measurement approach for the CEMIG system. Two dynamic load model structures are developed and tested. A procedure for applying a set of measured data from an on-line transient recording system to develop load models is described. (author) 6 refs., 17 figs.

  7. Elevator deflections on the icing process

    Science.gov (United States)

    Britton, Randall K.

    1990-01-01

    The effect of elevator deflection of the horizontal stabilizer for certain icing parameters is investigated. Elevator deflection can severely change the lower and upper leading-edge impingement limits, and ice can accrete on the elevator itself. Also, elevator deflection had practically no effect on the maximum local collection efficiency. It is shown that for severe icing conditions (large water droplets), elevator deflections that increase the projected height of the airfoil can significantly increase the total collection efficiency of the airfoil.

  8. Stress envelope of silicon carbide composites at elevated temperatures

    International Nuclear Information System (INIS)

    Nozawa, Takashi; Kim, Sunghun; Ozawa, Kazumi; Tanigawa, Hiroyasu

    2014-01-01

    To identify a comprehensive stress envelope, i.e., strength anisotropy map, of silicon carbide fiber-reinforced silicon carbide matrix composite (SiC/SiC composite) for practical component design, tensile and compressive tests were conducted using the small specimen test technique specifically tailored for high-temperature use. In-plane shear properties were, however, estimated using the off-axial tensile method and assuming that the mixed mode failure criterion, i.e., Tsai–Wu criterion, is valid for the composites. The preliminary test results indicate no significant degradation to either proportional limit stress (PLS) or fracture strength by tensile loading at temperatures below 1000 °C. A similarly good tolerance of compressive properties was identified at elevated temperatures, except for a slight degradation in PLS. With the high-temperature test data of tensile, compressive and in-plane shear properties, the stress envelopes at elevated temperatures were finally obtained. A slight reduction in the design limit was obvious at elevated temperatures when the compressive mode is dominant, whereas a negligibly small impact on the design is expected by considering the tensile loading case

  9. Stress envelope of silicon carbide composites at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Nozawa, Takashi, E-mail: nozawa.takashi67@jaea.go.jp [Japan Atomic Energy Agency, 2-166 Omotedate, Obuchi, Rokkasho, Aomori 039-3212 (Japan); Kim, Sunghun [Graduate School of Energy Science, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Ozawa, Kazumi; Tanigawa, Hiroyasu [Japan Atomic Energy Agency, 2-166 Omotedate, Obuchi, Rokkasho, Aomori 039-3212 (Japan)

    2014-10-15

    To identify a comprehensive stress envelope, i.e., strength anisotropy map, of silicon carbide fiber-reinforced silicon carbide matrix composite (SiC/SiC composite) for practical component design, tensile and compressive tests were conducted using the small specimen test technique specifically tailored for high-temperature use. In-plane shear properties were, however, estimated using the off-axial tensile method and assuming that the mixed mode failure criterion, i.e., Tsai–Wu criterion, is valid for the composites. The preliminary test results indicate no significant degradation to either proportional limit stress (PLS) or fracture strength by tensile loading at temperatures below 1000 °C. A similarly good tolerance of compressive properties was identified at elevated temperatures, except for a slight degradation in PLS. With the high-temperature test data of tensile, compressive and in-plane shear properties, the stress envelopes at elevated temperatures were finally obtained. A slight reduction in the design limit was obvious at elevated temperatures when the compressive mode is dominant, whereas a negligibly small impact on the design is expected by considering the tensile loading case.

  10. Når elever producerer

    DEFF Research Database (Denmark)

    Bremholm, Jesper; Hansen, Rune; Slot, Marie Falkesgaard

    2017-01-01

    Dette kapitel præsenterer centrale resultater fra studiet Elevopgaver og elevproduktion i det 21. århundrede der blandt andet rummer den første større kvantitative undersøgelse af opgavedidaktik og elevers produktive arbejde i den danske grundskole. Studiet omfatter også en kvalitativ del, og i...... undersøgelsen præsenteres og diskuteres gennem en række konkrete eksempler fra de berørte fag. I forhold til elevers produktive arbejde peger undersøgelsens resultater både på potentialer og særlige barrierer i forbindelse med at udvikle en kompetenceorienteret undervisning. I kapitlet argumenteres desuden...

  11. Læring mellem elever

    DEFF Research Database (Denmark)

    Georgsen, Marianne; Davidsen, Jacob

    2010-01-01

    I denne rapport præsenteres resultater fra følgeforskningen til projektet Læring gennem Bevægelse, som er gennemført på Søndervangskolen i Hammel i perioden august 2009 - maj 2010. Projektet er gennemført i samspil mellem lærere, it-vejleder, elever og skolens ledelse. Projektets overordnede formål...

  12. Distracted and confused?: selective attention under load.

    Science.gov (United States)

    Lavie, Nilli

    2005-02-01

    The ability to remain focused on goal-relevant stimuli in the presence of potentially interfering distractors is crucial for any coherent cognitive function. However, simply instructing people to ignore goal-irrelevant stimuli is not sufficient for preventing their processing. Recent research reveals that distractor processing depends critically on the level and type of load involved in the processing of goal-relevant information. Whereas high perceptual load can eliminate distractor processing, high load on "frontal" cognitive control processes increases distractor processing. These findings provide a resolution to the long-standing early and late selection debate within a load theory of attention that accommodates behavioural and neuroimaging data within a framework that integrates attention research with executive function.

  13. Size of Left Cardiac Chambers Correlates with Cerebral Microembolic Load in Open Heart Operations

    Directory of Open Access Journals (Sweden)

    Elena Z. Golukhova

    2010-01-01

    Full Text Available Background. Microemboli are a widely recognized etiological factor of cerebral complications in cardiac surgery patients. The present study was aimed to determine if size of left cardiac chambers relates to cerebral microembolic load in open heart operations. Methods. Thirty patients participated in the study. Echocardiography was performed in 2-3 days before surgery. A transcranial Doppler system was used for registering intraoperative microemboli. Results. Preoperative left atrium and left ventricular end-systolic and end-diastolic sizes significantly correlated with intraoperative microembolic load (s=0.48, 0.57 and 0.53, s≺.01, resp.. The associations between left ventricular diameters and number of cerebral microemboli remained significant when cardiopulmonary bypass time was included as a covariate into the analysis. Conclusions. The present results demonstrate that increased size of left heart chambers is an influential risk factor for elevated cerebral microembolic load during open heart operations. Mini-invasive surgery and carbon dioxide insufflation into wound cavity may be considered as neuroprotective approaches in patients with high risk of cerebral microembolism.

  14. Use of NDE and FM for the assessment of remaining life of steam turbines

    Energy Technology Data Exchange (ETDEWEB)

    Alley, T [Duke Power Co., Charlotte, NC (United States); Stone, R [Electric Power Research Inst., Charlotte, NC (United States). Nondestructive Evaluation Center

    1988-12-31

    Catastrophic failures of rotating turbine components, such as the Gallatin rotor burst in 1974 and the shrunk-on disk rupture at Hinkley Point in 1969, alerted the utility industry to the failure potential of these components. Such failures can cause severe financial loss; endanger personnel; and, in nuclear plants, damage safety related equipment. To adequately predict the remaining life of a turbine rotor requires accurate information about component flaws, material properties, future operating loads, relevant failure mechanisms, and an approach to combine this information to make an assessment of remaining life. EPRI has supported the development of improved ultrasonic test equipment for use from the rotor bore (bore-sonic examination) and a fracture mechanics based life assessment code called SAFER (Stress and Fracture Evaluation of Rotors). The EPRI NDE Center has supported the transfer of this technology to industry. This presentation deals with the NDE Center`s transfer of the NDE and life assessment technology to industry and discusses a particular application by Duke Power Company at their Allen Plant, Unit 1 to extend the operating life of an IP/LP turbine. (author).

  15. Use of NDE and FM for the assessment of remaining life of steam turbines

    International Nuclear Information System (INIS)

    Alley, T.; Stone, R.

    1988-01-01

    Catastrophic failures of rotating turbine components, such as the Gallatin rotor burst in 1974 and the shrunk-on disk rupture at Hinkley Point in 1969, alerted the utility industry to the failure potential of these components. Such failures can cause severe financial loss; endanger personnel; and, in nuclear plants, damage safety related equipment. To adequately predict the remaining life of a turbine rotor requires accurate information about component flaws, material properties, future operating loads, relevant failure mechanisms, and an approach to combine this information to make an assessment of remaining life. EPRI has supported the development of improved ultrasonic test equipment for use from the rotor bore (bore-sonic examination) and a fracture mechanics based life assessment code called SAFER (Stress and Fracture Evaluation of Rotors). The EPRI NDE Center has supported the transfer of this technology to industry. This presentation deals with the NDE Center's transfer of the NDE and life assessment technology to industry and discusses a particular application by Duke Power Company at their Allen Plant, Unit 1 to extend the operating life of an IP/LP turbine. (author)

  16. Elevational characteristics of the archaeal community in full-scale activated sludge wastewater treatment plants at a 3,660-meter elevational scale.

    Science.gov (United States)

    Niu, Lihua; Zhang, Xue; Li, Yi; Wang, Peifang; Zhang, Wenlong; Wang, Chao; Wang, Qing

    2017-07-01

    Due to the important roles of archaea in wastewater treatment processes, archaeal communities have been studied extensively in various anaerobic reactors, but the knowledge of archaeal communities in full-scale activated sludge wastewater treatment plants (WWTPs) remains quite poor. In this study, 454-pyrosequencing was for the first time employed to investigate archaeal communities from 20 full-scale activated sludge WWTPs distributed at a 3,660-meter elevational scale in China. Results showed that archaeal communities from WWTPs were dominated by Methanosarcinales (84.6%). A core archaeal population (94.5%) composed of Methanosaeta, Methanosarcina, Methanogenium and Methanobrevibacter was shared among WWTPs. The elevational pattern of archaeal communities was observed in WWTPs, with an elevational threshold associated with archaeal community richness and structures at approximately 1,500 meters above sea level (masl). A declining trend in community richness with increasing elevation was observed at higher elevations, whereas no trend was presented at lower elevations. Spearman correlation analysis indicated that the archaeal community richness at higher elevations was associated with more environmental variables than that at lower elevations. Redundancy analysis indicated that wastewater variables were the dominant contributors to the variation of community structures at higher elevations, followed by operational variables and elevation.

  17. Creep Behavior of High-Strength Concrete Subjected to Elevated Temperatures

    OpenAIRE

    Minho Yoon; Gyuyong Kim; Youngsun Kim; Taegyu Lee; Gyeongcheol Choe; Euichul Hwang; Jeongsoo Nam

    2017-01-01

    Strain is generated in concrete subjected to elevated temperatures owing to the influence of factors such as thermal expansion and design load. Such strains resulting from elevated temperatures and load can significantly influence the stability of a structure during and after a fire. In addition, the lower the water-to-binder (W?B) ratio and the smaller the quantity of aggregates in high-strength concrete, the more likely it is for unstable strain to occur. Hence, in this study, the compressi...

  18. The Statistical Properties of Host Load

    Directory of Open Access Journals (Sweden)

    Peter A. Dinda

    1999-01-01

    Full Text Available Understanding how host load changes over time is instrumental in predicting the execution time of tasks or jobs, such as in dynamic load balancing and distributed soft real‐time systems. To improve this understanding, we collected week‐long, 1 Hz resolution traces of the Digital Unix 5 second exponential load average on over 35 different machines including production and research cluster machines, compute servers, and desktop workstations. Separate sets of traces were collected at two different times of the year. The traces capture all of the dynamic load information available to user‐level programs on these machines. We present a detailed statistical analysis of these traces here, including summary statistics, distributions, and time series analysis results. Two significant new results are that load is self‐similar and that it displays epochal behavior. All of the traces exhibit a high degree of self‐similarity with Hurst parameters ranging from 0.73 to 0.99, strongly biased toward the top of that range. The traces also display epochal behavior in that the local frequency content of the load signal remains quite stable for long periods of time (150–450 s mean and changes abruptly at epoch boundaries. Despite these complex behaviors, we have found that relatively simple linear models are sufficient for short‐range host load prediction.

  19. Load Balancing in Hypergraphs

    Science.gov (United States)

    Delgosha, Payam; Anantharam, Venkat

    2018-03-01

    Consider a simple locally finite hypergraph on a countable vertex set, where each edge represents one unit of load which should be distributed among the vertices defining the edge. An allocation of load is called balanced if load cannot be moved from a vertex to another that is carrying less load. We analyze the properties of balanced allocations of load. We extend the concept of balancedness from finite hypergraphs to their local weak limits in the sense of Benjamini and Schramm (Electron J Probab 6(23):13, 2001) and Aldous and Steele (in: Probability on discrete structures. Springer, Berlin, pp 1-72, 2004). To do this, we define a notion of unimodularity for hypergraphs which could be considered an extension of unimodularity in graphs. We give a variational formula for the balanced load distribution and, in particular, we characterize it in the special case of unimodular hypergraph Galton-Watson processes. Moreover, we prove the convergence of the maximum load under some conditions. Our work is an extension to hypergraphs of Anantharam and Salez (Ann Appl Probab 26(1):305-327, 2016), which considered load balancing in graphs, and is aimed at more comprehensively resolving conjectures of Hajek (IEEE Trans Inf Theory 36(6):1398-1414, 1990).

  20. Structural load combinations

    International Nuclear Information System (INIS)

    Hwang, H.; Reich, M.; Ellingwood, B.; Shinozuka, M.

    1985-01-01

    This paper presents the latest results of the program entitled, ''Probability Based Load Combinations For Design of Category I Structures''. In FY 85, a probability-based reliability analysis method has been developed to evaluate safety of shear wall structures. The shear walls are analyzed using stick models with beam elements and may be subjected to dead load, live load and in-plane eqrthquake. Both shear and flexure limit states are defined analytically. The limit state probabilities can be evaluated on the basis of these limit states. Utilizing the reliability analysis method mentioned above, load combinations for the design of shear wall structures have been established. The proposed design criteria are in the load and resistance factor design (LRFD) format. In this study, the resistance factors for shear and flexure and load factors for dead and live loads are preassigned, while the load factor for SSE is determined for a specified target limit state probability of 1.0 x 10 -6 or 1.0 x 10 -5 during a lifetime of 40 years. 23 refs., 9 tabs

  1. Load Induced Blindness

    Science.gov (United States)

    Macdonald, James S. P.; Lavie, Nilli

    2008-01-01

    Although the perceptual load theory of attention has stimulated a great deal of research, evidence for the role of perceptual load in determining perception has typically relied on indirect measures that infer perception from distractor effects on reaction times or neural activity (see N. Lavie, 2005, for a review). Here we varied the level of…

  2. Structural load combinations

    International Nuclear Information System (INIS)

    Hwang, H.; Reich, M.; Ellingwood, B.; Shinozuka, M.

    1986-01-01

    This paper presents the latest results of the program entitled, ''Probability Based Load Combinations For Design of Category I Structures''. In FY 85, a probability-based reliability analysis method has been developed to evaluate safety of shear wall structures. The shear walls are analyzed using stick models with beam elements and may be subjected to dead load, live load and in-plane earthquake. Both shear and flexure limit states are defined analytically. The limit state probabilities can be evaluated on the basis of these limit states. Utilizing the reliability analysis method mentioned above, load combinations for the design of shear wall structures have been established. The proposed design criteria are in the load and resistance factor design (LRFD) format. In this study, the resistance factors for shear and flexure and load factors for dead and live loads are preassigned, while the load factor for SSE is determined for a specified target limit state probability of 1.0 x 10 -6 or 1.0 x 10 -5 during a lifetime of 40 years

  3. Load event: Aircraft crash

    International Nuclear Information System (INIS)

    Fritsch, H.

    1985-01-01

    The bibliography includes 48 quotations, up to the year 1983, on the following issues: Experiments and computational methods. Design load for the dimensioning of reinforced concrete buildings and components with respect to the dynamic load in the event of an aircraft crash. (orig./HP) [de

  4. 76 FR 14057 - Notice of Inventory Completion: University of Wyoming, Anthropology Department, Human Remains...

    Science.gov (United States)

    2011-03-15

    ...: University of Wyoming, Anthropology Department, Human Remains Repository, Laramie, WY AGENCY: National Park... Anthropology Department, Human Remains Repository, Laramie, WY. The human remains and associated funerary... the human remains was made by University of Wyoming, Anthropology Department, Human Remains Repository...

  5. Retinal Ganglion Cell Loss in Diabetes Associated with Elevated Homocysteine

    Directory of Open Access Journals (Sweden)

    Kenneth S. Shindler

    2009-11-01

    Full Text Available A number of studies have suggested that homocysteine may be a contributing factor to development of retinopathy in diabetic patients based on observed correlations between elevated homocysteine levels and the presence of retinopathy. The significance of such a correlation remains to be determined, and potential mechanisms by which homocysteine might induce retinopathy have not been well characterized. Ganapathy and colleagues1 used mutant mice that have endogenously elevated homocysteine levels due to heterozygous deletion of the cystathionine-β-synthase gene to examine changes in retinal pathology following induction of diabetes. Their finding that elevated homocysteine levels hastens loss of cells in the retinal ganglion cell layer suggests that toxicity to ganglion cells may warrant further investigation as a potential mechanism of homocysteine enhanced susceptibility to diabetic retinopathy.

  6. Assessment of lumen degradation and remaining useful life of LEDs using particle filter

    Energy Technology Data Exchange (ETDEWEB)

    Lall, Pradeep [Auburn Univ., AL (United States); Zhang, Hao [Auburn Univ., AL (United States); Davis, Lynn [Auburn Univ., AL (United States)

    2013-07-16

    With the development of light-emitting diode (LED) technology, light emitting diodes system is becoming a popular light source in daily life and industry area. It has shown that Led from same factory and work under same working condition, may have significantly different behavior. Therefore, it is very important to learn the fail mechanisms, especially in the case of safety critical and harsh environment application. This paper focus on a prognostic health management (PHM) method based on the measurement of forward voltage and forward current of bare LED under harsh environment. In this paper, experiment has been done with ten samples. Ten pristine bare LEDs have been tested at 85°C while simultaneously being subjected to 85% humid environment. Pulse width modulation (PWM) control method has been employed to drive the bare LED in order to reduce the heat effect caused by forward current and high frequency (300HZ) data acquisition has been used to measure the peak forward voltage and forward current. Test to failure (lumen drops to 70 percent) data has been measured to study the effects of high temperature and humid environment loadings on the bare LED. Also, solid state cooling method with peltier cooler has been used to control the temperature of LED in the integrating sphere when take the measurement of lumen flux. The shift of forward voltage forward current curve and lumen degradation has been recorded to help build the fail model and predicted the remaining useful life. In this method, particle filter has been employed to predict the remaining useful life (RUL) of the bare LED and give us a whole picture how Led system fails. Result shows that predication of remaining useful life of Led, made by the particle filter model works under reasonable limit, and hence this method can be employed to predict the failure of Led caused by thermal and humid stress under harsh environment.

  7. Bearing load distribution studies in a multi bearing rotor system and a remote computing method based on the internet

    International Nuclear Information System (INIS)

    Yang, Zhao Jian; Peng, Ze Jun; Kim, Seock Sam

    2004-01-01

    A model in the form of a Bearing Load Distribution (BLD) matrix in the Multi Bearing Rotor System (MBRS) is established by a transfer matrix equation with the consideration of a bearing load, elevation and uniform load distribution. The concept of Bearing Load Sensitivity (BLS) is proposed and matrices for load and elevation sensitivity are obtained. In order to share MBRS design resources on the internet with remote customers, the basic principle of Remote Computing (RC) based on the internet is introduced ; the RC of the BLD and BLS is achieved by Microsoft Active Server Pages (ASP) technology

  8. Load Balancing Scientific Applications

    Energy Technology Data Exchange (ETDEWEB)

    Pearce, Olga Tkachyshyn [Texas A & M Univ., College Station, TX (United States)

    2014-12-01

    The largest supercomputers have millions of independent processors, and concurrency levels are rapidly increasing. For ideal efficiency, developers of the simulations that run on these machines must ensure that computational work is evenly balanced among processors. Assigning work evenly is challenging because many large modern parallel codes simulate behavior of physical systems that evolve over time, and their workloads change over time. Furthermore, the cost of imbalanced load increases with scale because most large-scale scientific simulations today use a Single Program Multiple Data (SPMD) parallel programming model, and an increasing number of processors will wait for the slowest one at the synchronization points. To address load imbalance, many large-scale parallel applications use dynamic load balance algorithms to redistribute work evenly. The research objective of this dissertation is to develop methods to decide when and how to load balance the application, and to balance it effectively and affordably. We measure and evaluate the computational load of the application, and develop strategies to decide when and how to correct the imbalance. Depending on the simulation, a fast, local load balance algorithm may be suitable, or a more sophisticated and expensive algorithm may be required. We developed a model for comparison of load balance algorithms for a specific state of the simulation that enables the selection of a balancing algorithm that will minimize overall runtime.

  9. Status of load management

    Energy Technology Data Exchange (ETDEWEB)

    Juchymenko, A

    1983-08-01

    A summary is presented of the status of load management, defined as any activity by an electric utility to affect the size and characteristics of its load. Load management is currently viewed by electric utilities as an important tool for marketing electricity in a competitive fuel situation. A major aim of the National Energy Program is to reduce Canada's dependence on oil by 1990 to 10% of the energy used by all markets. As a result, electricity may play a greater role in the supply of primary energy. Research in load management has been directed mostly towards the residential market, especially direct control of domestic hot water heaters and air conditioners. Studies conducted in Canada and the U.S. to determine user's receptiveness to direct control of loads and thermal energy storage systems indicate that these load management techniques are in most cases not acceptable to customers, who prefer voluntary reduction in demand. The potential exists in the industrial market to use load management to assist in electrifying many of the fossil fuel-fired processes at competitive energy prices. Some of the more important applications include an industrial heat pump to heat liquids to 120{degree}C, induction heating for melting and heat treating of metals, and mechanical vapor recompression equipment to produce proces steam. 21 refs., 2 figs., 2 tabs.

  10. Mechanism for elevated temperature leaching

    International Nuclear Information System (INIS)

    Kenna, B.T.; Murphy, K.D.

    1979-01-01

    Long-term, elevated temperature leaching and subsequent electron microprobe analysis of simulated waste glass and ceramic materials have been completed. A cyclic leaching pattern was found in all systems over a 20-month period. It appears that the leaching of mobile ions by simple diffusional processes is modified by more complex chemical interactions. The release of immobile ions is primarily a function of their chemical interactions in the matrix which suggests that these ions may be complex species when released into solution. A mechanism is proposed which incorporates these ideas and the cyclic phenomenon observed

  11. PLC VVVF Elevator Control System

    OpenAIRE

    Tang, Yujian; Gui, Tianyu

    2016-01-01

    The aim of the thesis is to introduce the PLC VVVF elevator and its control system. The thesis can be divided into three parts. The first part is about the overview of the lift: the kinds of the lift and the structure of the lift, it shows the knowledge about the components and the operating systems of the lift. The second part is about the PLC control system, it’s about the operations of the lift from the introduction about the hardware and software of the PLC control system. And the thi...

  12. Amorphisation during elevated temperature implantation

    International Nuclear Information System (INIS)

    Carter, G.; Nobes, M.J.; Elliman, R.G.

    1994-01-01

    Transition state theory is employed to predict the rates of amorphous zone recrystallization by direct thermal and radiation mediated thermal annealing processes. These rates are functions of zone radius and are employed to describe the competition between amorphous zone generation and annealing during elevated temperature heavy ion implantation of, particularly, Si and the accumulation of amorphousness with increasing ion fluence. This analysis predicts a change from monotonic to sigmoidal to biexponential accumulation functions with increasing annealing rate or substrate temperature in agreement with experiments. A logarithmic dependence of ion flux density upon substrate temperature for the achievement of defined fractional amorphisation is predicted and is also in agreement with the experiment. (author)

  13. Factor structure underlying components of allostatic load.

    Directory of Open Access Journals (Sweden)

    Jeanne M McCaffery

    Full Text Available Allostatic load is a commonly used metric of health risk based on the hypothesis that recurrent exposure to environmental demands (e.g., stress engenders a progressive dysregulation of multiple physiological systems. Prominent indicators of response to environmental challenges, such as stress-related hormones, sympatho-vagal balance, or inflammatory cytokines, comprise primary allostatic mediators. Secondary mediators reflect ensuing biological alterations that accumulate over time and confer risk for clinical disease but overlap substantially with a second metric of health risk, the metabolic syndrome. Whether allostatic load mediators covary and thus warrant treatment as a unitary construct remains to be established and, in particular, the relation of allostatic load parameters to the metabolic syndrome requires elucidation. Here, we employ confirmatory factor analysis to test: 1 whether a single common factor underlies variation in physiological systems associated with allostatic load; and 2 whether allostatic load parameters continue to load on a single common factor if a second factor representing the metabolic syndrome is also modeled. Participants were 645 adults from Allegheny County, PA (30-54 years old, 82% non-Hispanic white, 52% female who were free of confounding medications. Model fitting supported a single, second-order factor underlying variance in the allostatic load components available in this study (metabolic, inflammatory and vagal measures. Further, this common factor reflecting covariation among allostatic load components persisted when a latent factor representing metabolic syndrome facets was conjointly modeled. Overall, this study provides novel evidence that the modeled allostatic load components do share common variance as hypothesized. Moreover, the common variance suggests the existence of statistical coherence above and beyond that attributable to the metabolic syndrome.

  14. Safety of Prasugrel Loading Doses in Patients Pre-Loaded With Clopidogrel in the Setting of Primary Percutaneous Coronary Intervention

    DEFF Research Database (Denmark)

    Räber, Lorenz; Klingenberg, Roland; Heg, Dik

    2015-01-01

    OBJECTIVES: The aim of this study was to assess the safety of the concurrent administration of a clopidogrel and prasugrel loading dose in patients undergoing primary percutaneous coronary intervention. BACKGROUND: Prasugrel is one of the preferred P2Y12 platelet receptor antagonists for ST-segment.......62, p = 0.36). CONCLUSIONS: This observational, nonrandomized study of ST-segment elevation myocardial infarction patients suggests that the administration of a loading dose of prasugrel in patients pre-treated with a loading dose of clopidogrel is not associated with an excess of major bleeding events...

  15. Elevation alters ecosystem properties across temperate treelines globally

    Science.gov (United States)

    Mayor, Jordan R.; Sanders, Nathan J.; Classen, Aimée T.; Bardgett, Richard D.; Clément, Jean-Christophe; Fajardo, Alex; Lavorel, Sandra; Sundqvist, Maja K.; Bahn, Michael; Chisholm, Chelsea; Cieraad, Ellen; Gedalof, Ze'Ev; Grigulis, Karl; Kudo, Gaku; Oberski, Daniel L.; Wardle, David A.

    2017-01-01

    Temperature is a primary driver of the distribution of biodiversity as well as of ecosystem boundaries. Declining temperature with increasing elevation in montane systems has long been recognized as a major factor shaping plant community biodiversity, metabolic processes, and ecosystem dynamics. Elevational gradients, as thermoclines, also enable prediction of long-term ecological responses to climate warming. One of the most striking manifestations of increasing elevation is the abrupt transitions from forest to treeless alpine tundra. However, whether there are globally consistent above- and belowground responses to these transitions remains an open question. To disentangle the direct and indirect effects of temperature on ecosystem properties, here we evaluate replicate treeline ecotones in seven temperate regions of the world. We find that declining temperatures with increasing elevation did not affect tree leaf nutrient concentrations, but did reduce ground-layer community-weighted plant nitrogen, leading to the strong stoichiometric convergence of ground-layer plant community nitrogen to phosphorus ratios across all regions. Further, elevation-driven changes in plant nutrients were associated with changes in soil organic matter content and quality (carbon to nitrogen ratios) and microbial properties. Combined, our identification of direct and indirect temperature controls over plant communities and soil properties in seven contrasting regions suggests that future warming may disrupt the functional properties of montane ecosystems, particularly where plant community reorganization outpaces treeline advance.

  16. Physics of untied rotating space elevators

    Science.gov (United States)

    Knudsen, Steven; Golubović, Leonardo

    2015-12-01

    We explore fundamental aspects of the physics of a novel class of dynamical systems, Rotating Space Elevators (RSE) (L. Golubović, S. Knudsen, Europhys. Lett. 86, 34001 (2009) and S. Knudsen, L. Golubović, Eur. Phys. J. Plus 129, 242 (2014)). An RSE is a loopy string reaching deep into outer space. The floppy RSE loop executes a double rotating motion due to which the objects sliding along the RSE string (climbers) can be transported far away from the Earth's surface without using internal engines or propulsion. By extensive numerical simulations and analytic calculations, this study addresses an interesting and provocative question at the very heart of the RSE physics: What will happen if one unties the rotating space elevator from the Earth? We find that the untied RSE exhibits rich nonlinear dynamics. In particular, strikingly, we find that the untied RSE may still behave as if it were tied to the planet. Such a quasi-tied yet untied RSE remains close to the Earth and exhibits persistent shape and enduring double rotating motion. Moreover, the climbers sliding along such a quasi-tied RSE move in much the same way as they do along a tied RSE. Under some conditions however we find that the untied RSE may undergo an instability leading it to a dynamical state in which the RSE hops well above the Earth surface. By changing the untied RSE parameters, the maximum height reached during hopping may be made to diverge. Such an untied RSE unbinds from the Earth to infinity, i.e., to interplanetary space.

  17. Latest trends in variable speed drive systems. ; Application to elevators. Kahensoku drive system no saishin doko. ; Elevator eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Inaba, H. (Hitachi, Ltd., Tokyo (Japan))

    1992-07-12

    The history of the elevator development may be summarized as a challenge to heights of buildings, pursuit of energy saving, and realizing comfort. Transfer of its drive system to the inverter drive system has been nearly completed keeping the pace with advance of electronic technologies. This paper describes control systems of elevators, effects of introducing inverters, and future trends. The inverter system used widely now for standard elevators with a speed lower than 105 m/min consists of a converter to rectify the utility power, a regenerative power consuming circuit to suppress overvoltage in the DC stage, and an inverter to supply power to induction motors. Those elevators exceeding a 120 m/min speed use power regenerating inverter system, with its converter controlled using micro computers according to loads and speeds of motors. The inverter system is particularly marked for having realized energy saving, lower power consumption, lower environmental pollution (from harmonics), comfort and maintainability at high levels. 13 refs., 9 figs.

  18. Diffusion rates for elevated releases

    International Nuclear Information System (INIS)

    Ramsdell, J.V.

    1983-11-01

    A search of the literature related to diffusion from elevated sources has determined that an adequate data base exists for use in developing parameterizations for estimating diffusion rates for material released from free standing stacks at nuclear power plants. A review of published data analyses indicates that a new parameterization of horizontal diffusion rates specifically for elevated releases is not likely to significantly change the magnitudes of horizontal diffusion coefficients on the average. However, the uncertainties associated with horizontal diffusion coefficient estimates under any given set of atmospheric conditions could be reduced by a new parameterization. Similarly, a new parameterization of vertical diffusion rates would be unlikely to significantly alter the magnitudes of diffusion coefficients for unstable atmospheric conditons. However, for neutral and stable atmospheric conditions, a new parameterization of vertical diffusion rates might increase vertical diffusion coefficients significantly. The increase would move ground-level time-integrated concentration maxima closer to the plant and would increase the maxima. 55 references, 2 figures, 4 tables

  19. Operation experience with elevated ammonia

    International Nuclear Information System (INIS)

    Vankova, Katerina; Kysela, Jan; Malac, Miroslav; Petrecky, Igor; Svarc, Vladimir

    2011-01-01

    The 10 VVER units in the Czech and Slovak Republics are all in very good water chemistry and radiation condition, yet questions have arisen regarding the optimization of cycle chemistry and improved operation in these units. To address these issues, a comprehensive experimental program for different water chemistries of the primary circuit was carried out at the Rez Nuclear Research Institute, Czech Republic, with the goal of judging the influence of various water chemistries on radiation build-up. Four types of water chemistries were compared: standard VVER water chemistry (in common use), direct hydrogen dosing without ammonia, standard VVER water chemistry with elevated ammonia levels, and zinc dosing to standard VVER water chemistry. The test results showed that the types of water chemistry other than the common one have benefits for the operation of the nuclear power plant (NPP) primary circuit. Operation experience with elevated ammonia at NPP Dukovany Units 3 and 4 is presented which validates the experimental results, demonstrating improved corrosion product volume activity. (orig.)

  20. Digitial Elevation Model (DEM) 100K

    Data.gov (United States)

    Kansas Data Access and Support Center — Digital Elevation Model (DEM) is the terminology adopted by the USG to describe terrain elevation data sets in a digital raster form. The standard DEM consists of a...

  1. Digtial Elevation Model (DEM) 250K

    Data.gov (United States)

    Kansas Data Access and Support Center — Digital Elevation Model (DEM) is the terminology adopted by the USGS to describe terrain elevation data sets in a digital raster form. The standard DEM consists of a...

  2. Digital Elevation Model (DEM) 24K

    Data.gov (United States)

    Kansas Data Access and Support Center — Digital Elevation Model (DEM) is the terminology adopted by the USGS to describe terrain elevation data sets in a digital raster form. The standard DEM consists of a...

  3. Auditory working memory load impairs visual ventral stream processing: toward a unified model of attentional load.

    Science.gov (United States)

    Klemen, Jane; Büchel, Christian; Bühler, Mira; Menz, Mareike M; Rose, Michael

    2010-03-01

    Attentional interference between tasks performed in parallel is known to have strong and often undesired effects. As yet, however, the mechanisms by which interference operates remain elusive. A better knowledge of these processes may facilitate our understanding of the effects of attention on human performance and the debilitating consequences that disruptions to attention can have. According to the load theory of cognitive control, processing of task-irrelevant stimuli is increased by attending in parallel to a relevant task with high cognitive demands. This is due to the relevant task engaging cognitive control resources that are, hence, unavailable to inhibit the processing of task-irrelevant stimuli. However, it has also been demonstrated that a variety of types of load (perceptual and emotional) can result in a reduction of the processing of task-irrelevant stimuli, suggesting a uniform effect of increased load irrespective of the type of load. In the present study, we concurrently presented a relevant auditory matching task [n-back working memory (WM)] of low or high cognitive load (1-back or 2-back WM) and task-irrelevant images at one of three object visibility levels (0%, 50%, or 100%). fMRI activation during the processing of the task-irrelevant visual stimuli was measured in the lateral occipital cortex and found to be reduced under high, compared to low, WM load. In combination with previous findings, this result is suggestive of a more generalized load theory, whereby cognitive load, as well as other types of load (e.g., perceptual), can result in a reduction of the processing of task-irrelevant stimuli, in line with a uniform effect of increased load irrespective of the type of load.

  4. Lumbriculus variegatus loading study

    Data.gov (United States)

    U.S. Environmental Protection Agency — Results from sediment bioaccumulation tests with Lumbriculus variegatus with evaluating the effects of organism loading density. This dataset is associated with the...

  5. LOADING SIMULATION PROGRAM C

    Science.gov (United States)

    LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for simulating hydrology, sediment, and general water quality

  6. LOADING SIMULATION PROGRAM C

    Data.gov (United States)

    U.S. Environmental Protection Agency — LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for...

  7. Cognitive load theory

    NARCIS (Netherlands)

    Kirschner, Paul A.; Kirschner, Femke; Paas, Fred

    2010-01-01

    Kirschner, P. A., Kirschner, F. C., & Paas, F. (2009). Cognitive load theory. In E. M. Anderman & L. H. Anderman (Eds.). Psychology of classroom learning: An encyclopedia, Volume 1, a-j (pp. 205-209). Detroit, MI: Macmillan Reference.

  8. Static Loads Test Facility

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Provides the capability to perform large-scale structural loads testing on spacecraft and other structures. Results from these tests can be used to verify...

  9. Load proportional safety brake

    Science.gov (United States)

    Cacciola, M. J.

    1979-01-01

    This brake is a self-energizing mechanical friction brake and is intended for use in a rotary drive system. It incorporates a torque sensor which cuts power to the power unit on any overload condition. The brake is capable of driving against an opposing load or driving, paying-out, an aiding load in either direction of rotation. The brake also acts as a no-back device when torque is applied to the output shaft. The advantages of using this type of device are: (1) low frictional drag when driving; (2) smooth paying-out of an aiding load with no runaway danger; (3) energy absorption proportional to load; (4) no-back activates within a few degrees of output shaft rotation and resets automatically; and (5) built-in overload protection.

  10. Plug Load Data

    Data.gov (United States)

    National Aeronautics and Space Administration — We provide MATLAB binary files (.mat) and comma separated values files of data collected from a pilot study of a plug load management system that allows for the...

  11. Quantification and Simulation of Metal Loading to the Upper Animas River, Eureka to Silverton, San Juan County, Colorado, September 1997 and August 1998

    Science.gov (United States)

    Paschke, Suzanne S.; Kimball, Briant A.; Runkel, Robert L.

    2005-01-01

    Drainage from abandoned and inactive mines and from naturally mineralized areas in the San Juan Mountains of southern Colorado contributes metals to the upper Animas River near Silverton, Colorado. Tracer-injection studies and associated synoptic sampling were performed along two reaches of the upper Animas River to develop detailed profiles of stream discharge and to locate and quantify sources of metal loading. One tracer-injection study was performed in September 1997 on the Animas River reach from Howardsville to Silverton, and a second study was performed in August 1998 on the stream reach from Eureka to Howardsville. Drainage in the upper Animas River study reaches contributed aluminum, calcium, copper, iron, magnesium, manganese, sulfate, and zinc to the surface-water system in 1997 and 1998. Colloidal aluminum, dissolved copper, and dissolved zinc were attenuated through a braided stream reach downstream from Eureka. Instream dissolved copper concentrations were lower than the State of Colorado acute and chronic toxicity standards downstream from the braided reach to Silverton. Dissolved iron load and concentrations increased downstream from Howardsville and Arrastra Gulch, and colloidal iron remained constant at low concentrations downstream from Howardsville. Instream sulfate concentrations were lower than the U.S. Environmental Protection Agency's secondary drinking-water standard of 250 milligrams per liter throughout the two study reaches. Elevated zinc concentrations are the primary concern for aquatic life in the upper Animas River. In the 1998 Eureka to Howardsville study, instream dissolved zinc load increased downstream from the Forest Queen mine, the Kittimack tailings, and Howardsville. In the 1997 Howardsville to Silverton study, there were four primary areas where zinc load increased. First, was the increase downstream from Howardsville and abandoned mining sites downstream from the Cunningham Gulch confluence, which also was measured during

  12. Lung Abscess Remains a Life-Threatening Condition in Pediatrics – A Case Report

    Directory of Open Access Journals (Sweden)

    Chirteș Ioana Raluca

    2017-07-01

    Full Text Available Pulmonary abscess or lung abscess is a lung infection which destroys the lung parenchyma leading to cavitations and central necrosis in localised areas formed by thick-walled purulent material. It can be primary or secondary. Lung abscesses can occur at any age, but it seems that paediatric pulmonary abscess morbidity is lower than in adults. We present the case of a one year and 5-month-old male child admitted to our clinic for fever, loss of appetite and an overall altered general status. Laboratory tests revealed elevated inflammatory biomarkers, leukocytosis with neutrophilia, anaemia, thrombocytosis, low serum iron concentration and increased lactate dehydrogenase level. Despite wide-spectrum antibiotic therapy, the patient’s progress remained poor after seven days of treatment and a CT scan established the diagnosis of a large lung abscess. Despite changing the antibiotic therapy, surgical intervention was eventually needed. There was a slow but steady improvment and eventually, the patient was discharged after approximately five weeks.

  13. Effect of venous (gut) CO2 loading on intrapulmonary gas fractions and ventilation in the tegu lizard.

    Science.gov (United States)

    Ballam, G O; Donaldson, L A

    1988-01-01

    Studies were conducted to determine regional pulmonary gas concentrations in the tegu lizard lung. Additionally, changes in pulmonary gas concentrations and ventilatory patterns caused by elevating venous levels of CO2 by gut infusion were measured. It was found that significant stratification of lung gases was present in the tegu and that dynamic fluctuations of CO2 concentration varied throughout the length of the lung. Mean FCO2 was greater and FO2 less in the posterior regions of the lung. In the posterior regions gas concentrations remained nearly constant, whereas in the anterior regions large swings were observed with each breath. In the most anterior sections of the lung near the bronchi, CO2 and O2 concentrations approached atmospheric levels during inspiration and posterior lung levels during expiration. During gut loading of CO2, the rate of rise of CO2 during the breathing pause increased. The mean level of CO2 also increased. Breathing rate and tidal volume increased to produce a doubling of VE. These results indicate that the method of introduction of CO2 into the tegu respiratory system determines the ventilatory response. If the CO2 is introduced into the venous blood a dramatic increase in ventilation is observed. If the CO2 is introduced into the inspired air a significant decrease in ventilation is produced. The changes in pulmonary CO2 environment caused by inspiratory CO2 loading are different from those caused by venous CO2 loading. We hypothesize that the differences in pulmonary CO2 environment caused by either inspiratory CO2 loading or fluctuations in venous CO2 concentration act differently on the IPC. The differing response of the IPC to the two methods of CO2 loading is the cause of the opposite ventilatory response seen during either venous or inspiratory loading.

  14. History of Elevators and Related Research

    Science.gov (United States)

    Abe, Shigeru; Watanabe, Eiki

    The history of traction drive elevators in Japan is described. The electrical technologies such as the microprocessor car control and the VVVF motor control made remarkable progress leading to higher reliability and energy savings. Then, the various machine-room-less elevators have been developed and the space saving technology, such as the shuttle and the double-deck elevators become important, too. The elevators used for evacuation in case of emergencies are also discussed.

  15. Time Remains

    OpenAIRE

    Gryb, Sean; Thebault, Karim

    2014-01-01

    On one popular view, the general covariance of gravity implies that change is relational in a strong sense, such that all it is for a physical degree of freedom to change is for it to vary with regard to a second physical degree of freedom. At a quantum level, this view of change as relative variation leads to a fundamentally timeless formalism for quantum gravity. Here, we will show how one may avoid this acute 'problem of time'. Under our view, duration is still regarded as relative, but te...

  16. 21 CFR 890.3930 - Wheelchair elevator.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Wheelchair elevator. 890.3930 Section 890.3930 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... elevator. (a) Identification. A wheelchair elevator is a motorized lift device intended for medical...

  17. 46 CFR 183.540 - Elevators.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Elevators. 183.540 Section 183.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) ELECTRICAL INSTALLATION Miscellaneous Systems and Requirements § 183.540 Elevators. Each elevator on a vessel must meet the requirements of ANSI A 17.1 ...

  18. Global variation in elevational diversity patterns

    Science.gov (United States)

    Qinfeng Guo; Douglas A. Kelt; Zhongyu Sun; Hongxiao Liu; Liangjun Hu; Hai Ren; Jun We

    2013-01-01

    While horizontal gradients of biodiversity have been examined extensively in the past, vertical diversity gradients (elevation, water depth) are attracting increasing attention. We compiled data from 443 elevational gradients involving diverse organisms worldwide to investigate how elevational diversity patterns may vary between the Northern and Southern hemispheres...

  19. Dynamic load effects on gate valve operability

    International Nuclear Information System (INIS)

    Steele, R. Jr.; MacDonald, P.E.; Arendts, J.G.

    1986-01-01

    The Idaho National Engineering Laboratory (INEL) participated in an internationally sponsored seismic research program conducted at the decommissioned Heissdampfreaktor (HDR) located in the Federal Republic of Germany. An existing piping system was modified by installation of an 8-in., naturally aged, motor-operated gate valve from a US nuclear power plant and a piping support system of US design. Six other piping support systems of varying flexibility from stiff to flexible were also installed at various times during the tests. Additional valve loadings included internal hydraulic loads and, during one block of tests, elevated temperature. The operability and integrity of the aged gate valve and the dynamic response of the various piping support system were measured during 25 representative seismic events

  20. Performance of a cognitive load inventory during simulated handoffs: Evidence for validity.

    Science.gov (United States)

    Young, John Q; Boscardin, Christy K; van Dijk, Savannah M; Abdullah, Ruqayyah; Irby, David M; Sewell, Justin L; Ten Cate, Olle; O'Sullivan, Patricia S

    2016-01-01

    Advancing patient safety during handoffs remains a public health priority. The application of cognitive load theory offers promise, but is currently limited by the inability to measure cognitive load types. To develop and collect validity evidence for a revised self-report inventory that measures cognitive load types during a handoff. Based on prior published work, input from experts in cognitive load theory and handoffs, and a think-aloud exercise with residents, a revised Cognitive Load Inventory for Handoffs was developed. The Cognitive Load Inventory for Handoffs has items for intrinsic, extraneous, and germane load. Students who were second- and sixth-year students recruited from a Dutch medical school participated in four simulated handoffs (two simple and two complex cases). At the end of each handoff, study participants completed the Cognitive Load Inventory for Handoffs, Paas' Cognitive Load Scale, and one global rating item for intrinsic load, extraneous load, and germane load, respectively. Factor and correlational analyses were performed to collect evidence for validity. Confirmatory factor analysis yielded a single factor that combined intrinsic and germane loads. The extraneous load items performed poorly and were removed from the model. The score from the combined intrinsic and germane load items associated, as predicted by cognitive load theory, with a commonly used measure of overall cognitive load (Pearson's r = 0.83, p load during handoffs may be measured via a self-report measure. Additional work is required to develop an adequate measure of extraneous load.

  1. Load power device, system and method of load control and management employing load identification

    Science.gov (United States)

    Yang, Yi; Luebke, Charles John; Schoepf, Thomas J.

    2018-01-09

    A load power device includes a power input, at least one power output for at least one load, a plurality of sensors structured to sense voltage and current at the at least one power output, and a processor. The processor provides: (a) load identification based upon the sensed voltage and current, and (b) load control and management based upon the load identification.

  2. Bentonite Permeability at Elevated Temperature

    Directory of Open Access Journals (Sweden)

    Katherine A. Daniels

    2017-01-01

    Full Text Available Repository designs frequently favour geological disposal of radioactive waste with a backfill material occupying void space around the waste. The backfill material must tolerate the high temperatures produced by decaying radioactive waste to prevent its failure or degradation, leading to increased hydraulic conductivity and reduced sealing performance. The results of four experiments investigating the effect of temperature on the permeability of a bentonite backfill are presented. Bentonite is a clay commonly proposed as the backfill in repository designs because of its high swelling capacity and very low permeability. The experiments were conducted in two sets of purpose-built, temperature controlled apparatus, designed to simulate isotropic pressure and constant volume conditions within the testing range of 4–6 MPa average effective stress. The response of bentonite during thermal loading at temperatures up to 200 °C was investigated, extending the previously considered temperature range. The results provide details of bentonite’s intrinsic permeability, total stress, swelling pressure and porewater pressure during thermal cycles. We find that bentonite’s hydraulic properties are sensitive to thermal loading and the type of imposed boundary condition. However, the permeability change is not large and can mostly be accounted for by water viscosity changes. Thus, under 150 °C, temperature has a minimal impact on bentonite’s hydraulic permeability.

  3. Myocarditis with ST elevation and elevated cardiac enzymes misdiagnosed as an ST-elevation myocardial infarction.

    Science.gov (United States)

    Sheldon, Seth H; Crandall, Mark A; Jaffe, Allan S

    2012-12-01

    Acute myocarditis can mimic ST-elevation myocardial infarction (STEMI). Quickly determining the correct diagnosis is critical given the "time is muscle" implication with a STEMI and the potential adverse effects associated with use of fibrinolytic therapy. A 46-year-old man presented to a rural emergency department with chest pain, and an electrocardiogram (ECG) read as showing 0.1 mV of ST-segment elevation in leads III and aVF. His initial cardiac troponin T was 0.44 ng/mL. He received fibrinolytic therapy for presumed STEMI. Cardiac magnetic resonance imaging was later performed and showed epicardial delayed enhancement consistent with myocarditis. Upon further questioning, he acknowledged 3 days of stuttering chest discomfort and a recent upper respiratory infection, as well as similar chest pain in his wife. A systematic evaluation is essential for acute chest pain, including a focused history, identification of cardiac risk factors, and ECG interpretation. A history of recent viral illness, absence of cardiac risk factors, or ECG findings inconsistent with a single anatomic lesion would suggest a potential alternate diagnosis to STEMI. This case emphasizes the importance of a focused history in the initial evaluation of chest pain. Copyright © 2012 Elsevier Inc. All rights reserved.

  4. At the end of a two-year follow-up elevated TSH levels normalize or remain unchanged in most the children with subclinical hypothyroidism

    Directory of Open Access Journals (Sweden)

    De Luca Filippo

    2010-01-01

    Full Text Available Abstract Data about the natural evolution of subclinical hypothyroidism (SH in pediatric age are very scanty. Moreover all the available reports in both aged and young patients were based on unselected study populations including also patients with either thyroid disorders or other pathological causes that are well known to be able to affect SH development and evolution. Aim of the study by Wasniewska et al was to prospectively evaluate for the first time the natural course of SH in children and adolescents with no underlying diseases and no risk factors that might interfere with the progression of SH. On the basis of the 2-year follow-up results, the Authors concluded that: a the natural course of TSH values in a pediatric population with idiopathic SH is characterized by a progressive decrease over time; b the majority of patients (88% normalized or maintained unchanged their TSH; and c TSH changes were not associated with changes of either FT4 values or clinical status or auxological parameters. Study design of this study is very accurate and the results are robust, thus supporting the Authors' conclusions.

  5. Performance of elevated tanks in Mw 7.7 Bhuj earthquake of ...

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    2001-01-26

    Jan 26, 2001 ... strength analysis of a few damaged shaft type stagings clearly shows that all of them either met or ... Elevated water tanks; staging; shaft support; reinforced concrete; earthquakes; damage. Proc. ..... lar thin RC sections with high axial load behave ... hollow circular columns, a masters' thesis submitted to.

  6. Community and ecosystem responses to elevational gradients

    DEFF Research Database (Denmark)

    Sundqvist, Maja K.; Sanders, Nate; Wardle, David A.

    2013-01-01

    Community structure and ecosystem processes often vary along elevational gradients. Their responses to elevation are commonly driven by changes in temperature, and many community- and ecosystem-level variables therefore frequently respond similarly to elevation across contrasting gradients...... elevational gradients for understanding community and ecosystem responses to global climate change at much larger spatial and temporal scales than is possible through conventional ecological experiments. However, future studies that integrate elevational gradient approaches with experimental manipulations...... will provide powerful information that can improve predictions of climate change impacts within and across ecosystems....

  7. Low reflectance radio frequency load

    Science.gov (United States)

    Ives, R. Lawrence; Mizuhara, Yosuke M

    2014-04-01

    A load for traveling microwave energy has an absorptive volume defined by cylindrical body enclosed by a first end cap and a second end cap. The first end cap has an aperture for the passage of an input waveguide with a rotating part that is coupled to a reflective mirror. The inner surfaces of the absorptive volume consist of a resistive material or are coated with a coating which absorbs a fraction of incident RF energy, and the remainder of the RF energy reflects. The angle of the reflector and end caps is selected such that reflected RF energy dissipates an increasing percentage of the remaining RF energy at each reflection, and the reflected RF energy which returns to the rotating mirror is directed to the back surface of the rotating reflector, and is not coupled to the input waveguide. Additionally, the reflector may have a surface which generates a more uniform power distribution function axially and laterally, to increase the power handling capability of the RF load. The input waveguide may be corrugated for HE11 mode input energy.

  8. Perceptual load corresponds with factors known to influence visual search.

    Science.gov (United States)

    Roper, Zachary J J; Cosman, Joshua D; Vecera, Shaun P

    2013-10-01

    One account of the early versus late selection debate in attention proposes that perceptual load determines the locus of selection. Attention selects stimuli at a late processing level under low-load conditions but selects stimuli at an early level under high-load conditions. Despite the successes of perceptual load theory, a noncircular definition of perceptual load remains elusive. We investigated the factors that influence perceptual load by using manipulations that have been studied extensively in visual search, namely target-distractor similarity and distractor-distractor similarity. Consistent with previous work, search was most efficient when targets and distractors were dissimilar and the displays contained homogeneous distractors; search became less efficient when target-distractor similarity increased irrespective of display heterogeneity. Importantly, we used these same stimuli in a typical perceptual load task that measured attentional spillover to a task-irrelevant flanker. We found a strong correspondence between search efficiency and perceptual load; stimuli that generated efficient searches produced flanker interference effects, suggesting that such displays involved low perceptual load. Flanker interference effects were reduced in displays that produced less efficient searches. Furthermore, our results demonstrate that search difficulty, as measured by search intercept, has little bearing on perceptual load. We conclude that rather than be arbitrarily defined, perceptual load might be defined by well-characterized, continuous factors that influence visual search. PsycINFO Database Record (c) 2013 APA, all rights reserved.

  9. On load paths and load bearing topology from finite element analysis

    International Nuclear Information System (INIS)

    Kelly, D; Reidsema, C; Lee, M

    2010-01-01

    Load paths can be mapped from vector plots of 'pointing stress vectors'. They define a path along which a component of load remains constant as it traverses the solution domain. In this paper the theory for the paths is first defined. Properties of the plots that enable a designer to interpret the structural behavior from the contours are then identified. Because stress is a second order tensor defined on an orthogonal set of axes, the vector plots define separate paths for load transfer in each direction of the set of axes. An algorithm is therefore presented that combines the vectors to define a topology to carry the loads. The algorithm is shown to straighten the paths reducing bending moments and removing stress concentration. Application to a bolted joint, a racing car body and a yacht hull demonstrate the usefulness of the plots.

  10. Creep Behavior of High-Strength Concrete Subjected to Elevated Temperatures.

    Science.gov (United States)

    Yoon, Minho; Kim, Gyuyong; Kim, Youngsun; Lee, Taegyu; Choe, Gyeongcheol; Hwang, Euichul; Nam, Jeongsoo

    2017-07-11

    Strain is generated in concrete subjected to elevated temperatures owing to the influence of factors such as thermal expansion and design load. Such strains resulting from elevated temperatures and load can significantly influence the stability of a structure during and after a fire. In addition, the lower the water-to-binder (W-B) ratio and the smaller the quantity of aggregates in high-strength concrete, the more likely it is for unstable strain to occur. Hence, in this study, the compressive strength, elastic modulus, and creep behavior were evaluated at target temperatures of 100, 200, 300, 500, and 800 °C for high-strength concretes with W-B ratios of 30%, 26%, and 23%. The loading conditions were set as non-loading and 0.33f cu . It was found that as the compressive strength of the concrete increased, the mechanical characteristics deteriorated and transient creep increased. Furthermore, when the point at which creep strain occurred at elevated temperatures after the occurrence of transient creep was considered, greater shrinkage strain occurred as the compressive strength of the concrete increased. At a heating temperature of 800 °C, the 80 and 100 MPa test specimens showed creep failure within a shrinkage strain range similar to the strain at the maximum load.

  11. Creep Behavior of High-Strength Concrete Subjected to Elevated Temperatures

    Directory of Open Access Journals (Sweden)

    Minho Yoon

    2017-07-01

    Full Text Available Strain is generated in concrete subjected to elevated temperatures owing to the influence of factors such as thermal expansion and design load. Such strains resulting from elevated temperatures and load can significantly influence the stability of a structure during and after a fire. In addition, the lower the water-to-binder (W–B ratio and the smaller the quantity of aggregates in high-strength concrete, the more likely it is for unstable strain to occur. Hence, in this study, the compressive strength, elastic modulus, and creep behavior were evaluated at target temperatures of 100, 200, 300, 500, and 800 °C for high-strength concretes with W–B ratios of 30%, 26%, and 23%. The loading conditions were set as non-loading and 0.33fcu. It was found that as the compressive strength of the concrete increased, the mechanical characteristics deteriorated and transient creep increased. Furthermore, when the point at which creep strain occurred at elevated temperatures after the occurrence of transient creep was considered, greater shrinkage strain occurred as the compressive strength of the concrete increased. At a heating temperature of 800 °C, the 80 and 100 MPa test specimens showed creep failure within a shrinkage strain range similar to the strain at the maximum load.

  12. Design of Cold-Formed Steel Screw Connections with Gypsum Sheathing at Ambient and Elevated Temperatures

    Directory of Open Access Journals (Sweden)

    Wei Chen

    2016-09-01

    Full Text Available Load-bearing cold-formed steel (CFS walls sheathed with double layers of gypsum plasterboard on both sides have demonstrated good fire resistance and attracted increasing interest for use in mid-rise CFS structures. As the main connection method, screw connections between CFS and gypsum sheathing play an important role in both the structural design and fire resistance of this wall system. However, studies on the mechanical behavior of screw connections with double-layer gypsum sheathing are still limited. In this study, 200 monotonic tests of screw connections with single- or double-layer gypsum sheathing at both ambient and elevated temperatures were conducted. The failure of screw connections with double-layer gypsum sheathing in shear was different from that of single-layer gypsum sheathing connections at ambient temperature, and it could be described as the breaking of the loaded sheathing edge combined with significant screw tilting and the loaded sheathing edge flexing fracture. However, the screw tilting and flexing fracture of the loaded sheathing edge gradually disappear at elevated temperatures. In addition, the influence of the loaded edge distance, double-layer sheathing and elevated temperatures is discussed in detail with clear conclusions. A unified design formula for the shear strength of screw connections with gypsum sheathing is proposed for ambient and elevated temperatures with adequate accuracy. A simplified load–displacement model with the post-peak branch is developed to evaluate the load–displacement response of screw connections with gypsum sheathing at ambient and elevated temperatures.

  13. INFLUENCE ANALYSES OF DESIGNED CHARACTERISTICS OF THE ELEVATOR TO THE PARAMETERS OF ITS DRIVE

    Directory of Open Access Journals (Sweden)

    V. M. Bohomaz

    2015-04-01

    Full Text Available Purpose. A drive behaves to the basic elements of scoop band elevators. To determine the drive power calculations are carried out according to standard methods, which take plenty of time. It is necessary to conduct the analysis of influence of project characteristics on the parameters of high-speed drive in a scoop bent elevator and to build the improved algorithm of speed-up determination of its drive power on project descriptions, that will take into account the type of load, rise height, necessary productivity, standard parameters of scoops and tape. Methodology. Using parametric dependences of elevators drive power on its project characteristics, received by the author earlier, the improved algorithm of speed-up determination of elevators high-speed drive power with deep and shallow scoops at set type of load, productivity, rise height was offered. Findings. The algorithm of drive power speed-up determination of high-speed vertical elevators with deep and shallow scoops depending on project parameters was offered. The example of such algorithm application is considered for an elevator that is intended for transporting of cement. Analytical dependences of drive power of such elevator are determined on the productivity and rise height. Corresponding graphic dependences were built and character of drive power changes during the size changing of any project characteristics was determined. Originality. The improved algorithm of drive power elevator determination at the given project characteristics (type of load, rise height, productivity that takes into account standard sizes, parameters of scoops and ribbons, was built at first time. Practical value. The use of an offered algorithm of calculation gives the possibility of relatively fast determination of reference value of high-speed elevators drive power with deep and shallow scoops, to build graphic dependences of drive power on the values of the productivity and rise height at the certain

  14. Ocean Tide Loading Computation

    Science.gov (United States)

    Agnew, Duncan Carr

    2005-01-01

    September 15,2003 through May 15,2005 This grant funds the maintenance, updating, and distribution of programs for computing ocean tide loading, to enable the corrections for such loading to be more widely applied in space- geodetic and gravity measurements. These programs, developed under funding from the CDP and DOSE programs, incorporate the most recent global tidal models developed from Topex/Poscidon data, and also local tide models for regions around North America; the design of the algorithm and software makes it straightforward to combine local and global models.

  15. DYNAMIC LOAD DAMPER MODELING

    Directory of Open Access Journals (Sweden)

    Loktev Aleksey Alekseevich

    2013-01-01

    Full Text Available The authors present their findings associated with their modeling of a dynamic load damper. According to the authors, the damper is to be installed onto a structure or its element that may be exposed to impact, vibration or any other dynamic loading. The damper is composed of paralleled or consecutively connected viscous and elastic elements. The authors study the influence of viscosity and elasticity parameters of the damper produced onto the regular displacement of points of the structure to be protected and onto the regular acceleration transmitted immediately from the damper to the elements positioned below it.

  16. Dynamic multibody modeling for tethered space elevators

    Science.gov (United States)

    Williams, Paul

    2009-08-01

    This paper presents a fundamental modeling strategy for dealing with powered and propelled bodies moving along space tethers. The tether is divided into a large number of discrete masses, which are connected by viscoelastic springs. The tether is subject to the full range of forces expected in Earth orbit in a relatively simple manner. Two different models of the elevator dynamics are presented. In order to capture the effect of the elevator moving along the tether, the elevator dynamics are included as a separate body in both models. One model treats the elevator's motion dynamically, where propulsive and friction forces are applied to the elevator body. The second model treats the elevator's motion kinematically, where the distance along the tether is determined by adjusting the lengths of tether on either side of the elevator. The tether model is used to determine optimal configurations for the space elevator. A modal analysis of two different configurations is presented which show that the fundamental mode of oscillation is a pendular one around the anchor point with a period on the order of 160 h for the in-plane motion, and 24 h for the out-of-plane motion. Numerical simulation results of the effects of the elevator moving along the cable are presented for different travel velocities and different elevator masses.

  17. Predictors of backrest elevation in critical care.

    Science.gov (United States)

    Grap, Mary Jo; Munro, Cindy L; Bryant, Sandra; Ashtiani, Brooke

    2003-04-01

    Low backrest and supine positions are associated with increased mortality and ventilator associated pneumonia (VAP). Data are not available across ICU settings about the level of backrest position used and its relationship to enteral feeding and hemodynamic status. The purpose of this descriptive study was to document the level of backrest elevation and position and identify factors associated with and predict positioning in a medical, surgical and neuroscience intensive care unit. Data were collected randomly in each unit over a 6-week period, resulting in 506 observations for170 patients. Backrest elevation was determined by electronic bed read-out or bed frame elevation gauge. BP, HR and enteral feeding status were retrieved from the medical record. Results showed that mean backrest elevation was 19.2 degrees and 70% of subjects were supine. No difference in backrest elevation among units was found. Significant correlations between backrest elevation and systolic BP (r=0.15, P=0.006); and backrest and diastolic BP (r=0.13, P=0.02) were found. There was no difference in backrest elevation between patients being fed and not being fed. Differences in backrest elevation for intubated versus nonintubated patients approached significance (P=0.07) with intubated patients at lower backrest elevations. In summary, use of higher backrest elevations (>30 degrees ) is minimal, is not related to feeding and minimally related to hemodynamic status. Strategies to meet published recommendations for backrest elevation (30-45 degrees ) must include repeated feedback about nurse's use of backrest elevation and estimates of elevation.

  18. A lateral approach for sinus elevation using PRGF technology.

    Science.gov (United States)

    Anitua, Eduardo; Prado, Roberto; Orive, Gorka

    2009-10-01

    A lateral approach for sinus elevation using plasma rich in growth factors (PRGF) technology is described. The long-term survival of dental implants installed following a two-stage procedure after sinus elevation using this procedure is reported, using implant loss as the outcome variable. A retrospective cohort study design was used. Eighteen patients received 43 implants (BTI implants, Biotechnology Institute, Vitoria, Spain) with sinus floor elevation. All patients presented a residual bone height of class D (1-3 mm). Implants were installed using a low-speed drilling procedure (50 rpm) without irrigation. Finally, the histological and histomorphometric evaluation of eight samples from PRGF grafted sinus involved in the study was carried out 5-6 months posttreatment. The overall survival rate of dental implants was 100%. The mean follow-up period for all implants was 33 +/- 7 months ranging from 24 to 44 months. In addition, the histomorphometrical evaluation of the samples evidenced a 25.24 +/- 4.62% of vital newly formed bone, 50.31 +/- 15.56% of soft connective tissue, and the remaining 24.46 +/- 12.79% of bovine anorganic bone. Based on these results, this new approach for sinus elevation and implant installation using PRGF technology can be considered safe, simple, effective, and predictable.

  19. Space elevator systems level analysis

    Energy Technology Data Exchange (ETDEWEB)

    Laubscher, B. E. (Bryan E.)

    2004-01-01

    The Space Elevator (SE) represents a major paradigm shift in space access. It involves new, untried technologies in most of its subsystems. Thus the successful construction of the SE requires a significant amount of development, This in turn implies a high level of risk for the SE. This paper will present a systems level analysis of the SE by subdividing its components into their subsystems to determine their level of technological maturity. such a high-risk endeavor is to follow a disciplined approach to the challenges. A systems level analysis informs this process and is the guide to where resources should be applied in the development processes. It is an efficient path that, if followed, minimizes the overall risk of the system's development. systems level analysis is that the overall system is divided naturally into its subsystems, and those subsystems are further subdivided as appropriate for the analysis. By dealing with the complex system in layers, the parameter space of decisions is kept manageable. Moreover, A rational way to manage One key aspect of a resources are not expended capriciously; rather, resources are put toward the biggest challenges and most promising solutions. This overall graded approach is a proven road to success. The analysis includes topics such as nanotube technology, deployment scenario, power beaming technology, ground-based hardware and operations, ribbon maintenance and repair and climber technology.

  20. Phase-preserved optical elevator.

    Science.gov (United States)

    Luo, Yuan; Zhang, Baile; Han, Tiancheng; Chen, Zhi; Duan, Yubo; Chu, Chia-Wei; Barbastathis, George; Qiu, Cheng Wei

    2013-03-25

    The unique superiority of transformation optics devices designed from coordinate transformation is their capability of recovering both ray trajectory and optical path length in light manipulation. However, very few experiments have been done so far to verify this dual-recovery property from viewpoints of both ray trajectory and optical path length simultaneously. The experimental difficulties arise from the fact that most previous optical transformation optics devices only work at the nano-scale; the lack of intercomparison between data from both optical path length and ray trajectory measurement in these experiments obscured the fact that the ray path was subject to a subwavelength lateral shift that was otherwise not easily perceivable and, instead, was pointed out theoretically [B. Zhang et al. Phys. Rev. Lett. 104, 233903, 2010]. Here, we use a simple macroscopic transformation optics device of phase-preserved optical elevator, which is a typical birefringent optical phenomenon that can virtually lift an optical image by a macroscopic distance, to demonstrate decisively the unique optical path length preservation property of transformation optics. The recovery of ray trajectory is first determined with no lateral shift in the reflected ray. The phase preservation is then verified with incoherent white-light interferometry without ambiguity and phase unwrapping.

  1. Defense of a space elevator

    Energy Technology Data Exchange (ETDEWEB)

    Laubscher, B. E. (Bryan E.)

    2004-01-01

    The Space Elevator (SE) represents a major paradigm shift in space access. If the SE's promise of low-cost access is to be realized, everything becomes economically more feasible to accomplish in space. In this paper we describe a defensive system of the SE. The primary scenario adopted for this analysis is the SE based on a floating platform in the ocean along the equator. A second possible scenario is the SE stationed on land (island or continent) on or near the equator. The SE will capture the imaginations of people around the world. It will become a symbol of power, capability, wealth and prestige for the country that builds it. As such, it will become a prime terrorist target. Moreover, the tremendous economic leverage afforded by the SE might motivate rogue nations to plot its destruction. Therefore, it is necessary to consider the requirements for defense of the SE. For the purposes of this paper it is assumed that the SE is to be deployed by the United States or one of its companies, and the resources of the US are available for its defense.

  2. Association of Adolescent- and Caregiver-Reported Antiretroviral Therapy Adherence with HIV Viral Load Among Perinatally-infected South African Adolescents.

    Science.gov (United States)

    Brittain, Kirsty; Asafu-Agyei, Nana Akua; Hoare, Jacqueline; Bekker, Linda-Gail; Rabie, Helena; Nuttall, James; Roux, Paul; Stein, Dan J; Zar, Heather J; Myer, Landon

    2018-03-01

    Accurate measurement of antiretroviral therapy (ART) adherence remains challenging and there are few data assessing the validity of self-reported adherence among perinatally HIV-infected adolescents. We examined adolescent and caregiver reports of adolescent adherence among perinatally-infected adolescents aged 9-14 years in Cape Town, South Africa, and explored factors that may modify associations between reported adherence and elevated viral load (VL). Among 474 adolescents (median age 12.0 years; median duration of ART use 7.5 years), elevated VL and caregiver- and adolescent-report of missed ART doses were common. Elevated VL was particularly prevalent among older, male adolescents. Low-moderate concordance was observed between caregiver and adolescent report. Among adolescents aged ≥ 12 years, caregiver- and adolescent-reported adherence was associated with elevated VL across most items assessed, but few significant associations were observed among adolescents adolescents who require adherence interventions are needed in this context.

  3. Lateral loadings on snubber assemblies

    International Nuclear Information System (INIS)

    Raphael, L.S.

    1981-01-01

    This paper examines the installation of snubber assemblies in power plants with respect to transverse or lateral loads as well as axial loads. Evaluation of the effects of low level, lateral loads was performed by analytical means. At higher loadings, the snubber assembly could no longer be treated as a column; therefore, the effects of lateral loadings was determined by test. The test consisted of applying both lateral and axial loads simultaneously. Results of both the analysis and the test showed that the application of lateral loads had a considerable effect on the snubber assemblies

  4. Fuel Load (FL)

    Science.gov (United States)

    Duncan C. Lutes; Robert E. Keane

    2006-01-01

    The Fuel Load method (FL) is used to sample dead and down woody debris, determine depth of the duff/ litter profile, estimate the proportion of litter in the profile, and estimate total vegetative cover and dead vegetative cover. Down woody debris (DWD) is sampled using the planar intercept technique based on the methodology developed by Brown (1974). Pieces of dead...

  5. HIV Viral Load

    Science.gov (United States)

    ... PF4 Antibody Hepatitis A Testing Hepatitis B Testing Hepatitis C Testing HER2/neu Herpes Testing High-sensitivity C-reactive Protein (hs-CRP) Histamine Histone Antibody HIV Antibody and HIV Antigen (p24) HIV Antiretroviral Drug Resistance Testing, Genotypic HIV Viral Load HLA Testing HLA- ...

  6. Loading device for incinerator

    International Nuclear Information System (INIS)

    Hempelmann, W.

    1983-01-01

    An incinerator for radioactive waste is described. Heat radiation from the incinerator into the loading device is reduced by the design of the slider with a ceramic plate and the conical widening of the pot, and also by fixing a metal plate between the pot and the floor. (PW) [de

  7. Side loading filter apparatus

    International Nuclear Information System (INIS)

    Reynolds, K.E.

    1981-01-01

    A side loading filter chamber for use with radioactive gases is described. The equipment incorporates an inexpensive, manually operated, mechanism for aligning filter units with a number of laterally spaced wall openings and for removing the units from the chamber. (U.K.)

  8. EQUATING FACULTY LOADS.

    Science.gov (United States)

    OOSTING, KENNETH W.

    AT ALPENA COMMUNITY COLLEGE, A NORMAL TEACHING LOAD FOR ANY FACULTY MEMBER IS 14-16 SEMESTER HOURS, WITH 75-125 STUDENTS AND 2-3 PREPARATIONS. VARIATIONS FROM THE SCHEDULE ARE IN ACCORDANCE WITH SPECIFIC FORMULAS RELATING TO TOTAL MEMBERS OF STUDENTS, NUMBERS OF PREPARATIONS, ASSIGNMENT TO ENGLISH COMPOSITION CLASSES, NEW COURSES, AND CLASSES…

  9. Probabilistic Load Flow

    DEFF Research Database (Denmark)

    Chen, Peiyuan; Chen, Zhe; Bak-Jensen, Birgitte

    2008-01-01

    This paper reviews the development of the probabilistic load flow (PLF) techniques. Applications of the PLF techniques in different areas of power system steady-state analysis are also discussed. The purpose of the review is to identify different available PLF techniques and their corresponding...

  10. Duration of load revisited

    DEFF Research Database (Denmark)

    Hoffmeyer, Preben; Sørensen, John Dalsgaard

    2007-01-01

    A duration of load study representing 13 years of testing was recently terminated. Preliminary results have been published over the years. This paper represents the final account of the study, which was focused on the influ-ence of moisture content on time to failure for structural timber subject...

  11. Robust surgery loading

    NARCIS (Netherlands)

    Hans, Elias W.; Wullink, Gerhard; van Houdenhoven, Mark; Kazemier, Geert

    2008-01-01

    We consider the robust surgery loading problem for a hospital’s operating theatre department, which concerns assigning surgeries and sufficient planned slack to operating room days. The objective is to maximize capacity utilization and minimize the risk of overtime, and thus cancelled patients. This

  12. Temoporfin-loaded liposomes

    DEFF Research Database (Denmark)

    Kuntsche, Judith; Freisleben, Ines; Steiniger, Frank

    2010-01-01

    . In contrast, if phospholipids with longer fatty acid chains (distearoylphosphatidylcholine/-glycerol) were used, phase transitions were well above body temperature even at high drug load. Size and thermal behavior were not distinctly influenced by the addition of pegylated lipids but cryo-electron microscopic...

  13. Broadband phase-preserved optical elevator

    OpenAIRE

    Luo, Yuan; Han, Tiancheng; Zhang, Baile; Qiu, Cheng-Wei; Barbastathis, George

    2011-01-01

    Phase-preserved optical elevator is an optical device to lift up an entire plane virtually without distortion in light path or phase. Using transformation optics, we have predicted and observed the realization of such a broadband phase-preserved optical elevator, made of a natural homogeneous birefringent crystal without resorting to absorptive and narrowband metamaterials involving time-consuming nano-fabrication. In our demonstration, the optical elevator is designed to lift a sheet upwards...

  14. Strain Measurement System Developed for Biaxially Loaded Cruciform Specimens

    Science.gov (United States)

    Krause, David L.

    2000-01-01

    A new extensometer system developed at the NASA Glenn Research Center at Lewis Field measures test area strains along two orthogonal axes in flat cruciform specimens. This system incorporates standard axial contact extensometers to provide a cost-effective high-precision instrument. The device was validated for use by extensive testing of a stainless steel specimen, with specimen temperatures ranging from room temperature to 1100 F. In-plane loading conditions included several static biaxial load ratios, plus cyclic loadings of various waveform shapes, frequencies, magnitudes, and durations. The extensometer system measurements were compared with strain gauge data at room temperature and with calculated strain values for elevated-temperature measurements. All testing was performed in house in Glenn's Benchmark Test Facility in-plane biaxial load frame.

  15. Distribution load forecast with interactive correction of horizon loads

    International Nuclear Information System (INIS)

    Glamochanin, V.; Andonov, D.; Gagovski, I.

    1994-01-01

    This paper presents the interactive distribution load forecast application that performs the distribution load forecast with interactive correction of horizon loads. It consists of two major parts implemented in Fortran and Visual Basic. The Fortran part is used for the forecasts computations. It consists of two methods: Load Transfer Coupling Curve Fitting (LTCCF) and load Forecast Using Curve Shape Clustering (FUCSC). LTCCF is used to 'correct' the contaminated data because of load transfer among neighboring distribution areas. FUCSC uses curve shape clustering to forecast the distribution loads of small areas. The forecast for each small area is achieved by using the shape of corresponding cluster curve. The comparison of forecasted loads of the area with historical data will be used as a tool for the correction of the estimated horizon load. The Visual Basic part is used to provide flexible interactive user-friendly environment. (author). 5 refs., 3 figs

  16. Load research manual. Volume 1. Load research procedures

    Energy Technology Data Exchange (ETDEWEB)

    Brandenburg, L.; Clarkson, G.; Grund, Jr., C.; Leo, J.; Asbury, J.; Brandon-Brown, F.; Derderian, H.; Mueller, R.; Swaroop, R.

    1980-11-01

    This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. In Volumes 1 and 2, procedures are suggested for determining data requirements for load research, establishing the size and customer composition of a load survey sample, selecting and using equipment to record customer electricity usage, processing data tapes from the recording equipment, and analyzing the data. Statistical techniques used in customer sampling are discussed in detail. The costs of load research also are estimated, and ongoing load research programs at three utilities are described. The manual includes guides to load research literature and glossaries of load research and statistical terms.

  17. Cogeneration feasibility: Otis Elevator Company and Polychrome Corporation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1982-05-01

    The purpose of this study was to assess the feasibility of cogeneration at Otis Elevator Company and Polychrome Corporation located in Westchester County, New York. Each plant and its associated thermal and electrical load is reviewed. Three basic cycles for the cogeneration are investigated: power only, power generation with waste heat recovery, and combined cycle. Each case was assessed economically, beginning with a screening method to suggest those configurations most likely to be implemented and continuing through an assessment of the regulatory environment for cogeneration and an analysis of rate structures for buy back power, displaced power, and supplementing service. It is concluded that: for a plant designed to supply the combined loads of the two corporations, interconnection costs coupled to the coincidence of load result in unfavorable economics; for separate cogeneration plants, owned and operated by each individual corporation, energy consumption patterns and the current regulatory environment, in particular the existing and proposed cogeneration system rate structures, do not permit viable economics for the proposed plants; but if the proposed cycle were owned and operated by a new entity (neither Otis/Polychrome nor the utility), an economic scheme with marginal financial benefits can be developed and may be worthy of further study. (LEW)

  18. Soil nematodes show a mid-elevation diversity maximum and elevational zonation on Mt. Norikura, Japan.

    Science.gov (United States)

    Dong, Ke; Moroenyane, Itumeleng; Tripathi, Binu; Kerfahi, Dorsaf; Takahashi, Koichi; Yamamoto, Naomichi; An, Choa; Cho, Hyunjun; Adams, Jonathan

    2017-06-08

    Little is known about how nematode ecology differs across elevational gradients. We investigated the soil nematode community along a ~2,200 m elevational range on Mt. Norikura, Japan, by sequencing the 18S rRNA gene. As with many other groups of organisms, nematode diversity showed a high correlation with elevation, and a maximum in mid-elevations. While elevation itself, in the context of the mid domain effect, could predict the observed unimodal pattern of soil nematode communities along the elevational gradient, mean annual temperature and soil total nitrogen concentration were the best predictors of diversity. We also found nematode community composition showed strong elevational zonation, indicating that a high degree of ecological specialization that may exist in nematodes in relation to elevation-related environmental gradients and certain nematode OTUs had ranges extending across all elevations, and these generalized OTUs made up a greater proportion of the community at high elevations - such that high elevation nematode OTUs had broader elevational ranges on average, providing an example consistent to Rapoport's elevational hypothesis. This study reveals the potential for using sequencing methods to investigate elevational gradients of small soil organisms, providing a method for rapid investigation of patterns without specialized knowledge in taxonomic identification.

  19. 76 FR 14058 - Notice of Inventory Completion: University of Wyoming, Anthropology Department, Human Remains...

    Science.gov (United States)

    2011-03-15

    ...: University of Wyoming, Anthropology Department, Human Remains Repository, Laramie, WY AGENCY: National Park... in the possession and control of the University of Wyoming Anthropology Department, Human Remains... made by University of Wyoming, Anthropology Department, Human Remains Repository, professional staff in...

  20. An Automatic System for Elevator Monitoring

    OpenAIRE

    Md. Haidar Sharif; Ibrahim Furkan Ince

    2015-01-01

    An elevator is a conveyor device or transport equipment that moves people or goods between floors or levels or decks of a building, vessel, or other structures. It has become a part and parcel of modern life in developed countries. The number of floors in high buildings, skyscrapers, and towers generate the usage of elevators. If it is simply assumed that each floor has at least two elevators in a thirty-floor building, people call the elevators in each floor even they are already occupied in...

  1. Elevated CO2 as a driver of global dryland greening

    KAUST Repository

    Lu, Xuefei; Wang, Lixin; McCabe, Matthew

    2016-01-01

    While recent findings based on satellite records indicate a positive trend in vegetation greenness over global drylands, the reasons remain elusive. We hypothesize that enhanced levels of atmospheric CO2 play an important role in the observed greening through the CO2 effect on plant water savings and consequent available soil water increases. Meta-analytic techniques were used to compare soil water content under ambient and elevated CO2 treatments across a range of climate regimes, vegetation types, soil textures and land management practices. Based on 1705 field measurements from 21 distinct sites, a consistent and statistically significant increase in the availability of soil water (11%) was observed under elevated CO2 treatments in both drylands and non-drylands, with a statistically stronger response over drylands (17% vs. 9%). Given the inherent water limitation in drylands, it is suggested that the additional soil water availability is a likely driver of observed increases in vegetation greenness.

  2. Elevated CO2 as a driver of global dryland greening

    KAUST Repository

    Lu, Xuefei

    2016-02-12

    While recent findings based on satellite records indicate a positive trend in vegetation greenness over global drylands, the reasons remain elusive. We hypothesize that enhanced levels of atmospheric CO2 play an important role in the observed greening through the CO2 effect on plant water savings and consequent available soil water increases. Meta-analytic techniques were used to compare soil water content under ambient and elevated CO2 treatments across a range of climate regimes, vegetation types, soil textures and land management practices. Based on 1705 field measurements from 21 distinct sites, a consistent and statistically significant increase in the availability of soil water (11%) was observed under elevated CO2 treatments in both drylands and non-drylands, with a statistically stronger response over drylands (17% vs. 9%). Given the inherent water limitation in drylands, it is suggested that the additional soil water availability is a likely driver of observed increases in vegetation greenness.

  3. Snow cover distribution over elevation zones in a mountainous catchment

    Science.gov (United States)

    Panagoulia, D.; Panagopoulos, Y.

    2009-04-01

    A good understanding of the elevetional distribution of snow cover is necessary to predict the timing and volume of runoff. In a complex mountainous terrain the snow cover distribution within a watershed is highly variable in time and space and is dependent on elevation, slope, aspect, vegetation type, surface roughness, radiation load, and energy exchange at the snow-air interface. Decreases in snowpack due to climate change could disrupt the downstream urban and agricultural water supplies, while increases could lead to seasonal flooding. Solar and longwave radiation are dominant energy inputs driving the ablation process. Turbulent energy exchange at the snow cover surface is important during the snow season. The evaporation of blowing and drifting snow is strongly dependent upon wind speed. Much of the spatial heterogeneity of snow cover is the result of snow redistribution by wind. Elevation is important in determining temperature and precipitation gradients along hillslopes, while the temperature gradients determine where precipitation falls as rain and snow and contribute to variable melt rates within the hillslope. Under these premises, the snow accumulation and ablation (SAA) model of the US National Weather Service (US NWS) was applied to implement the snow cover extent over elevation zones of a mountainous catchment (the Mesochora catchment in Western-Central Greece), taking also into account the indirectly included processes of sublimation, interception, and snow redistribution. The catchment hydrology is controlled by snowfall and snowmelt and the simulated discharge was computed from the soil moisture accounting (SMA) model of the US NWS and compared to the measured discharge. The elevationally distributed snow cover extent presented different patterns with different time of maximization, extinction and return during the year, producing different timing of discharge that is a crucial factor for the control and management of water resources systems.

  4. REMAINING LIFE TIME PREDICTION OF BEARINGS USING K-STAR ALGORITHM – A STATISTICAL APPROACH

    Directory of Open Access Journals (Sweden)

    R. SATISHKUMAR

    2017-01-01

    Full Text Available The role of bearings is significant in reducing the down time of all rotating machineries. The increasing trend of bearing failures in recent times has triggered the need and importance of deployment of condition monitoring. There are multiple factors associated to a bearing failure while it is in operation. Hence, a predictive strategy is required to evaluate the current state of the bearings in operation. In past, predictive models with regression techniques were widely used for bearing lifetime estimations. The Objective of this paper is to estimate the remaining useful life of bearings through a machine learning approach. The ultimate objective of this study is to strengthen the predictive maintenance. The present study was done using classification approach following the concepts of machine learning and a predictive model was built to calculate the residual lifetime of bearings in operation. Vibration signals were acquired on a continuous basis from an experiment wherein the bearings are made to run till it fails naturally. It should be noted that the experiment was carried out with new bearings at pre-defined load and speed conditions until the bearing fails on its own. In the present work, statistical features were deployed and feature selection process was carried out using J48 decision tree and selected features were used to develop the prognostic model. The K-Star classification algorithm, a supervised machine learning technique is made use of in building a predictive model to estimate the lifetime of bearings. The performance of classifier was cross validated with distinct data. The result shows that the K-Star classification model gives 98.56% classification accuracy with selected features.

  5. Cognitive load theory: Practical implications and an important challenge

    Directory of Open Access Journals (Sweden)

    Jimmie Leppink, Ph.D.

    2017-10-01

    Full Text Available The field of medical education has adopted a wide variety of theories from other fields. A fairly recent example is cognitive load theory, which originated in educational psychology. Several empirical studies inspired by cognitive load theory and reviews of practical implications of cognitive load theory have contributed to guidelines for the design of medical education. Simultaneously, several research groups have developed instruments for the measurement of cognitive load in a medical education context. These developments notwithstanding, obtaining evidence for different types of cognitive load remains an important challenge. Therefore, the aim of this article is twofold: to provide medical educators with three key guidelines for the design of instruction and assessment and to discuss several fundamental issues in the remaining challenges presented by different types of cognitive load. The guidelines revolve around minimizing cognitive activity that does not contribute to learning, working with specific learning goals in mind, and appreciating the multifaceted relation between learning and assessment. Key issues around the types of cognitive load include the context in which learning occurs, the continued use of single-item mental effort ratings, and the timing of cognitive load and learning outcome measurements.

  6. National requirements for improved elevation data

    Science.gov (United States)

    Snyder, Gregory I.; Sugarbaker, Larry J.; Jason, Allyson L.; Maune, David F.

    2014-01-01

    This report presents the results of surveys, structured interviews, and workshops conducted to identify key national requirements for improved elevation data for the United States and its territories, including coastlines. Organizations also identified and reported the expected economic benefits that would be realized if their requirements for improved elevation were met (appendixes 1–3). This report describes the data collection methodology and summarizes the findings. Participating organizations included 34 Federal agencies, 50 States and two territories, and a sampling of local governments, tribes, and nongovernmental orgnizations. The nongovernmental organizations included The Nature Conservancy and a sampling of private sector businesses. These data were collected in 2010-2011 as part of the National Enhanced Elevation Assessment (NEEA), a study to identify program alternatives for better meeting the Nation’s elevation data needs. NEEA tasks included the collection of national elevation requirements; analysis of the benefits and costs of meeting these requirements; assessment of emerging elevation technologies, lifecycle data management needs, and costs for managing and distributing a national-scale dataset and derived products; and candidate national elevation program alternatives that balance costs and benefits in meeting the Nation’s elevation requirements. The NEEA was sponsored by the National Digital Elevation Program (NDEP), a government coordination body with the U.S. Geological Survey (USGS) as managing partner that includes the National Geospatial-Intelligence Agency (NGA), the Federal Emergency Management Agency (FEMA), the Natural Resources Conservation Service (NRCS), the U.S. Army Corps of Engineers (USACE), and the National Oceanic and Atmospheric Administration (NOAA), among the more than a dozen agencies and organizations. The term enhanced elevation data as used in this report refers broadly to three-dimensional measurements of land or

  7. Load theory behind the wheel; perceptual and cognitive load effects.

    Science.gov (United States)

    Murphy, Gillian; Greene, Ciara M

    2017-09-01

    Perceptual Load Theory has been proposed as a resolution to the longstanding early versus late selection debate in cognitive psychology. There is much evidence in support of Load Theory but very few applied studies, despite the potential for the model to shed light on everyday attention and distraction. Using a driving simulator, the effect of perceptual and cognitive load on drivers' visual search was assessed. The findings were largely in line with Load Theory, with reduced distractor processing under high perceptual load, but increased distractor processing under high cognitive load. The effect of load on driving behaviour was also analysed, with significant differences in driving behaviour under perceptual and cognitive load. In addition, the effect of perceptual load on drivers' levels of awareness was investigated. High perceptual load significantly increased inattentional blindness and deafness, for stimuli that were both relevant and irrelevant to driving. High perceptual load also increased RTs to hazards. The current study helps to advance Load Theory by illustrating its usefulness outside of traditional paradigms. There are also applied implications for driver safety and roadway design, as the current study suggests that perceptual and cognitive load are important factors in driver attention. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  8. Load handling gripper

    International Nuclear Information System (INIS)

    Holloway, C.

    1982-01-01

    An apparatus for releasably engaging and moving workpieces comprises pivotable gripper jaws with a spring-loaded plunger to maintain the jaws in a closed condition. The plunger is slidable in a bore in a housing and the end of the plunger remote from the jaws cooperates with a blind end of the bore to provide a gas cushion. A rod in conjunction with a backplate (not shown) are provided to cause the jaws to open and release a workpiece on axial movement of the housing in a first direction through a predetermined distance and releasable locking means maintain the jaws in an open condition. On axial movement of the housing in the reverse direction the locking means are released to allow the spring-loaded plunger to return to a position to close to jaws. (author)

  9. Heavy-Load Lifting

    DEFF Research Database (Denmark)

    Bloomquist, Kira; Oturai, Peter; Steele, Megan L

    2018-01-01

    of the Creative Commons Attribution-Non Commercial-No Derivatives License 4.0 (CCBY-NC-ND), where it is permissible to download and share the work provided it is properly cited. The work cannot be changed in any way or used commercially without permission from the journal....... repetition maximum (RM), two sets of 15-20 repetitions) and heavy-load (85-90% 1RM, three sets of 5-8 repetition) upper-extremity resistance exercise separated by a one-week wash-out period. Swelling was determined by bioimpedance spectroscopy and dual energy x-ray absorptiometry, with breast cancer......-related lymphedema symptoms (heaviness, swelling, pain, tightness) reported using a numeric rating scale (0-10). Order of low- versus heavy-load was randomized. All outcomes were assessed pre-, immediately post-, and 24- and 72-hours post-exercise. Generalized estimating equations were used to evaluate changes over...

  10. Fuel element loading system

    International Nuclear Information System (INIS)

    Arya, S.P; s.

    1978-01-01

    A nuclear fuel element loading system is described which conveys a plurality of fuel rods to longitudinal passages in fuel elements. Conveyor means successively position the fuel rods above the longitudinal passages in axial alignment therewith and adapter means guide the fuel rods from the conveyor means into the longitudinal passages. The fuel elements are vibrated to cause the fuel rods to fall into the longitudinal passages through the adapter means

  11. TFTR generator load assessment

    International Nuclear Information System (INIS)

    Heck, F.M.

    1975-10-01

    Typical experimental load demands on the TFTR generators are illustrated based on the electrical characteristics of the field coils, the coil leads, the main bus work, the various auxiliary bus work, the rectifiers, and transformers. The generator MW capacities are shown to be adequate for the proposed experimental operations with allowances made for variations in the final designs. The generator MVA capacities are shown to be adequate provided portions of the TF and EF rectifiers are freewheeled at selected times

  12. 78 FR 14697 - Final Flood Elevation Determinations

    Science.gov (United States)

    2013-03-07

    ... Communities affected elevation above ground [caret] Elevation in meters (MSL) Modified Cecil County, Maryland... 1 to Stone Run At the Stone Run +271 Town of Rising Sun, confluence. Unincorporated Areas of Cecil County. Approximately 460 feet +359 downstream of Pierce Road. Tributary 2 to Stone Run At the Stone Run...

  13. 75 FR 31361 - Proposed Flood Elevation Determinations

    Science.gov (United States)

    2010-06-03

    ... source(s) elevation ground [caret] Elevation Communities affected in meters (MSL) Effective Modified... American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1.... Stone County, Mississippi, and Incorporated Areas Church House Branch Approximately 0.5 mile None +211...

  14. High elevation white pines educational website

    Science.gov (United States)

    Anna W. Schoettle; Michele Laskowski

    2011-01-01

    The high elevation five-needle white pines are facing numerous challenges ranging from climate change to invasion by a non-native pathogen to escalation of pest outbreaks. This website (http://www.fs.fed.us/rm/highelevationwhitepines/) serves as a primer for managers and the public on the high elevation North American five-needle pines. It presents information on each...

  15. 46 CFR 120.540 - Elevators.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Elevators. 120.540 Section 120.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150 PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS ELECTRICAL INSTALLATION Miscellaneous Systems and Requirements § 120.540 Elevators....

  16. Insect Population Dynamics in Commercial Grain Elevators

    Science.gov (United States)

    Data were collected in 1998-2002 from wheat stored in commercial grain elevators in south-central Kansas. Storage bins at these elevators had concrete walls and were typically 6-9 m in diameter and 30-35 m tall. A vacuum-probe sampler was used to collect ten 3-kg grain samples in the top 12 m of the...

  17. 75 FR 69892 - Final Flood Elevation Determinations

    Science.gov (United States)

    2010-11-16

    ...: * Elevation in feet (NGVD) + Elevation in feet (NAVD) State City/town/county Source of flooding Location Depth... county +899 City of Norwich, Town boundary. of Greene, Town of North Norwich, Town of Oxford, Town of...). Susquehanna River At the downstream county +965 Town of Afton, Town of boundary. Bainbridge, Village of Afton...

  18. 77 FR 6980 - Final Flood Elevation Determinations

    Science.gov (United States)

    2012-02-10

    ... in feet (NGVD) + Elevation in feet (NAVD) State City/town/county Source of flooding Location Depth in feet above ground [caret] Elevation in meters (MSL) Modified Unincorporated Areas of Nowata County... Bayou An area bounded by the +100 Town of Mayersville, county boundary to the Unincorporated Areas of...

  19. 76 FR 1535 - Final Flood Elevation Determinations

    Science.gov (United States)

    2011-01-11

    ... in feet (NGVD) + Elevation in feet (NAVD) State City/town/county Source of flooding Location Depth in feet above ground [caret] Elevation in meters (MSL) Modified Unincorporated Areas of Poinsett County... with the St. Francis River...... +212 Areas of Poinsett County. Approximately 0.45 mile downstream of...

  20. 75 FR 29253 - Proposed Flood Elevation Determinations

    Science.gov (United States)

    2010-05-25

    ...: * Elevation in feet (NGVD) + Elevation in feet (NAVD) Depth in feet above State City/town/county Source of... +21 Town of Ebro, upstream of the Unincorporated Areas confluence with the of Washington County. East... County, Colorado, and Incorporated Areas Willow Creek At the confluence with None +8,154 Unincorporated...

  1. 75 FR 68710 - Final Flood Elevation Determinations

    Science.gov (United States)

    2010-11-09

    ...: * Elevation in feet (NGVD) + Elevation in feet (NAVD) State City/town/county Source of flooding Location Depth... County, California Docket Nos.: FEMA-B-7762, FEMA-B-7795, and FEMA-B-1053 California Unincorporated Oregon Slough..... City of Montague +2503 Areas of Siskiyou and County. Unincorporated Siskiyou County...

  2. 76 FR 50918 - Final Flood Elevation Determinations

    Science.gov (United States)

    2011-08-17

    ... in feet (NGVD) + Elevation in feet (NAVD) Depth in feet State City/town/county Source of flooding... affected [caret] Elevation in meters (MSL) Modified Jones County, Texas, and Incorporated Areas Docket No.: FEMA-B-1122 Lake Fort Phantom Hill Just downstream of County +1642 City of Abilene, Highway 1082...

  3. 78 FR 10066 - Final Flood Elevation Determinations

    Science.gov (United States)

    2013-02-13

    ... follows: * Elevation in feet (NGVD) + Elevation in feet (NAVD) Depth in feet State City/town/county Source...). Scriba Creek Approximately 0.90 mile +546 Town of Amboy. upstream of County Route 23 (Potter Road.... Town of Palermo Maps are available for inspection at the Palermo Town Municipal Offices, 53 County...

  4. 77 FR 49379 - Final Flood Elevation Determinations

    Science.gov (United States)

    2012-08-16

    ... in feet (NGVD) + Elevation in feet (NAVD) State City/town/county Source of flooding Location Depth in feet above ground [caret] Elevation in meters (MSL) Modified Unincorporated Areas of Washington County... of the +35 Areas of railroad. Washington County. Approximately 2.1 miles upstream of the railroad...

  5. 75 FR 43418 - Final Flood Elevation Determinations

    Science.gov (United States)

    2010-07-26

    ... follows: * Elevation in feet (NGVD) + Elevation in feet (NAVD) State City/town/county Source of flooding... +869 Town of Peoria, upstream of Main Street. Unincorporated Areas of Ottawa County. Approximately 1.... Town of Peoria Maps are available for inspection at the Ottawa County Courthouse, 102 East Central...

  6. 78 FR 21272 - Final Flood Elevation Determinations

    Science.gov (United States)

    2013-04-10

    ... below for the modified BFEs for each community listed. These modified elevations have been published in... [Amended] 0 2. The tables published under the authority of Sec. 67.11 are amended as follows: * Elevation... Austin. upstream of 29th Avenue Southwest (County Highway 28). At the downstream side of +1205 I and M...

  7. Load responsive hydrodynamic bearing

    Science.gov (United States)

    Kalsi, Manmohan S.; Somogyi, Dezso; Dietle, Lannie L.

    2002-01-01

    A load responsive hydrodynamic bearing is provided in the form of a thrust bearing or journal bearing for supporting, guiding and lubricating a relatively rotatable member to minimize wear thereof responsive to relative rotation under severe load. In the space between spaced relatively rotatable members and in the presence of a liquid or grease lubricant, one or more continuous ring shaped integral generally circular bearing bodies each define at least one dynamic surface and a plurality of support regions. Each of the support regions defines a static surface which is oriented in generally opposed relation with the dynamic surface for contact with one of the relatively rotatable members. A plurality of flexing regions are defined by the generally circular body of the bearing and are integral with and located between adjacent support regions. Each of the flexing regions has a first beam-like element being connected by an integral flexible hinge with one of the support regions and a second beam-like element having an integral flexible hinge connection with an adjacent support region. A least one local weakening geometry of the flexing region is located intermediate the first and second beam-like elements. In response to application of load from one of the relatively rotatable elements to the bearing, the beam-like elements and the local weakening geometry become flexed, causing the dynamic surface to deform and establish a hydrodynamic geometry for wedging lubricant into the dynamic interface.

  8. Low-load high volume resistance exercise stimulates muscle protein synthesis more than high-load low volume resistance exercise in young men.

    Directory of Open Access Journals (Sweden)

    Nicholas A Burd

    Full Text Available BACKGROUND: We aimed to determine the effect of resistance exercise intensity (%1 repetition maximum-1RM and volume on muscle protein synthesis, anabolic signaling, and myogenic gene expression. METHODOLOGY/PRINCIPAL FINDINGS: Fifteen men (21+/-1 years; BMI=24.1+/-0.8 kg/m2 performed 4 sets of unilateral leg extension exercise at different exercise loads and/or volumes: 90% of repetition maximum (1RM until volitional failure (90FAIL, 30% 1RM work-matched to 90%FAIL (30WM, or 30% 1RM performed until volitional failure (30FAIL. Infusion of [ring-13C6] phenylalanine with biopsies was used to measure rates of mixed (MIX, myofibrillar (MYO, and sarcoplasmic (SARC protein synthesis at rest, and 4 h and 24 h after exercise. Exercise at 30WM induced a significant increase above rest in MIX (121% and MYO (87% protein synthesis at 4 h post-exercise and but at 24 h in the MIX only. The increase in the rate of protein synthesis in MIX and MYO at 4 h post-exercise with 90FAIL and 30FAIL was greater than 30WM, with no difference between these conditions; however, MYO remained elevated (199% above rest at 24 h only in 30FAIL. There was a significant increase in AktSer473 at 24h in all conditions (P=0.023 and mTORSer2448 phosphorylation at 4 h post-exercise (P=0.025. Phosporylation of Erk1/2Tyr202/204, p70S6KThr389, and 4E-BP1Thr37/46 increased significantly (P<0.05 only in the 30FAIL condition at 4 h post-exercise, whereas, 4E-BP1Thr37/46 phosphorylation was greater 24 h after exercise than at rest in both 90FAIL (237% and 30FAIL (312% conditions. Pax7 mRNA expression increased at 24 h post-exercise (P=0.02 regardless of condition. The mRNA expression of MyoD and myogenin were consistently elevated in the 30FAIL condition. CONCLUSIONS/SIGNIFICANCE: These results suggest that low-load high volume resistance exercise is more effective in inducing acute muscle anabolism than high-load low volume or work matched resistance exercise modes.

  9. The benefits of improved national elevation data

    Science.gov (United States)

    Snyder, Gregory I.

    2013-01-01

    This article describes how the National Enhanced Elevation Assessment (NEEA) has identified substantial benefits that could come about if improved elevation data were publicly available for current and emerging applications and business uses such as renewable energy, precision agriculture, and intelligent vehicle navigation and safety. In order to support these diverse needs, new national elevation data with higher resolution and accuracy are needed. The 3D Elevation Program (3DEP) initiative was developed to meet the majority of these needs and it is expected that 3DEP will result in new, unimagined information services that would result in job growth and the transformation of the geospatial community. Private-sector data collection companies are continuously evolving sensors and positioning technologies that are needed to collect improved elevation data. An initiative of this scope might also provide an opportunity for companies to improve their capabilities and produce even higher data quality and consistency at a pace that might not have otherwise occurred.

  10. Elevers refleksjoner over naturvitenskapens egenart

    Directory of Open Access Journals (Sweden)

    Anne Bergliot Øyehaug

    2014-05-01

    Full Text Available This paper reports from a study where a teacher and researchers collaborated on designing science teaching promoting scientific inquiry for a group of students (age 11 – 13. Guided by the Norwegian science curriculum, students were during a two year intervention period regularly engaged in inquiry-based science learning. The students formed and tested hypotheses, were to various degrees engaged in developing research design and took extensively part in evaluation of evidence. In connection with each inquiry task, students were encouraged to express their ideas about professional or formal science emphasized in the Norwegian science curriculum (Why do scientists form and test hypothesis? What characterize scientific inquiry? Why do scientists compare results?. Data (video recordings of classroom instructions and interviews in addition to written tests from four students were collected during a two year period. Results indicate that the students’ epistemological beliefs remained fairly naïve through the intervention period, in spite of intensive participation in inquiry learning. The students’ lack of epistemological development may be understood in terms of the instructional emphasis on formal epistemology, in favor of practical epistemology.

  11. Plastic limit loads for cylindrical shell intersections under combined loading

    International Nuclear Information System (INIS)

    Skopinsky, V.N.; Berkov, N.A.; Vogov, R.A.

    2015-01-01

    In this research, applied methods of nonlinear analysis and results of determining the plastic limit loads for shell intersection configurations under combined internal pressure, in-plane moment and out-plane moment loadings are presented. The numerical analysis of shell intersections is performed using the finite element method, geometrically nonlinear shell theory in quadratic approximation and plasticity theory. For determining the load parameter of proportional combined loading, the developed maximum criterion of rate of change of relative plastic work is employed. The graphical results for model of cylindrical shell intersection under different two-parameter combined loadings (as generalized plastic limit load curves) and three-parameter combined loading (as generalized plastic limit load surface) are presented on the assumption that the internal pressure, in-plane moment and out-plane moment loads were applied in a proportional manner. - Highlights: • This paper presents nonlinear two-dimensional FE analysis for shell intersections. • Determining the plastic limit loads under combined loading is considered. • Developed maximum criterion of rate of change of relative plastic work is employed. • Plastic deformation mechanism in shell intersections is discussed. • Results for generalized plastic limit load curves of branch intersection are presented

  12. Application of Combined Sustained and Cyclic Loading Test Results to Alloy 617 Elevated Temperature Design Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yanli [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jetter, Robert I [Global Egineering and Technology, LLC, Coral Gables, FL (United States); Sham, Sam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-08-25

    Alloy 617 is a reference structural material for very high temperature components of advanced-gas cooled reactors with outlet temperatures in the range of 900-950°C . In order for designers to be able to use Alloy 617 for these high temperature components, Alloy 617 has to be approved for use in Section III (the nuclear section) of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code. A plan has been developed to submit a draft code for Alloy 617 to ASME Section III by 2015. However, the current rules in Subsection NH for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 1200°F (650°C). The rationale for this exclusion is that at higher temperatures it is not feasible to decouple plasticity and creep deformation, which is the basis for the current simplified rules. This temperature, 1200 °F, is well below the temperature range of interest for this material in High Temperature Gas Cooled Reactor (HTGR) applications. The only current alternative is, thus, a full inelastic analysis which requires sophisticated material models which have been formulated but not yet verified. To address this issue, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (EPP) analysis methods and which are expected to be applicable to very high temperatures.

  13. Is phloem loading a driver of plant photosynthetic responses to elevated atmospheric [CO2]? 

    Science.gov (United States)

    A better understanding of the interactions between photosynthesis, photoassimilate translocation and sink activity is necessary to improve crop productivity. Rising atmospheric [CO2] is perturbing source-sink balance in a manner not experienced by crops during the history of their cultivation, so ne...

  14. The elevation of radiation load on ecosystems and genome instability of organisms

    International Nuclear Information System (INIS)

    Gaziyev, A. I.; Bezlepkin, V.Q.

    2002-01-01

    At present many countries actively develop the nuclear technologies of energy production. Simultaneously, a tendency persists for the propagation of nuclear weapons. Accordingly, the waste of the nuclear energy production and nuclear weapon industry products to be utilized constantly grow in amount. Besides, there is a risk of plunder of nuclear materials and diversions at nuclear plants. Therefore, in spite of the efforts that are constantly made to enhance the control and safety in this regard, there is still danger of radiation accidents and risk of environment contamination fraught with serious consequences for the biosphere. Today the radiation-ecological situation in the Caucasus-Caspian region may be considered favorable but the risk of its deterioration, as in the whole world, still persists. It should be taken into account that in this region two nuclear power complex plants, uranium mines and treatment facilities, research nuclear reactors as well as burial-grounds for radioactive waste are situated. Earlier (in the 70's-80's of the past century) 29 subsurface nuclear explosions (for geological survey) were performed in the northern part of the region. Release of radionuclides to the environment results in increased ionizing radiation background, which, in combination with other technogenic agents may be a serious hazard to all living things and produce a variety of harmful effects in living organisms, depending on the dose. The genetic consequences of radionuclide contamination of environment and of the combined effect of low-intensity radiation and non-radiation factors on humans (as well as on other living things) have been the subject matter of numerous recent scientific discussions. Studies in this field are essential for assessing the hazards associated with increased ionizing radiation background under the conditions of contamination of environment by anthropogenic agents as well as for development of techniques and means for radiation safety and prophylaxis of human disorders. Thus, it was found that the action of low-dose ionizing radiation on living organisms might induce an adaptive repair response in them aimed at decreasing the genetic consequences of the exposure. However, the potentialities of defense and repair systems of an organism are limited, so an increase in genome lesions may cause inheritable mutations, cancer and other pathologies, and death. DNA lesions caused by ionizing radiation in small and sublethal doses can essentially be repaired, whereas unrepaired lesions and errors of repair, replication, and recombination systems lead to formation of mutational changes in DNA sequences. These changes may be transmitted to daughter cells and induce genome instability in the progeny. Induced genome instability in survived somatic cells is characterized by persistence of a high level of acquired variability in many generations of these cells. Genome instability manifests itself as an increased frequency of karyotypic anomalies, chromosome and gene mutations, clonal heterogeneity, and malignant transformation in the progeny of cells exposed to DNA-damaging agents. Besides, cells with genome instability show increased amplification of genes and changes in their expression, as well as disturbances in their differentiation, delays in reproductive death and other phenotypic characters of abnormal development. Whereas some progress has been made towards knowledge of genome instability in the somatic cells of mammals, the radiation-induced genome instability in germ cells transmitted to individuals of the next generation is still not clearly understood. At the same time, evidence has been obtained which suggests that the transmission of genome instability to the somatic cells of the progeny from the germ cells of gamma - radiation-exposed parents is possible. This conclusion is based on the data on mutation frequency in the progeny of parents exposed to DNA-damaging agents. For instance, a significant increase in mutation frequency, as determined from analysis of polymorphism of protein markers, has been observed in children of parents survived from A-bomb attacks in Hiroshima and Nagasaki. An increase in cancer rate has been registered in children of parents exposed to ionizing radiation or employed at nuclear technology facilities under the conditions of increased radiation background. In rodents, the progeny born to radiation-exposed male parents showed increased gene and chromosome mutations and tumor induction. However, the best-reproduced results on genome instability transmission from parental germ cells to the somatic cells of the progeny were demonstrated by changes in variability of micro- and macro satellite tandem repeats of DNA. Thus, experimental and epidemiological evidence has been obtained that radiation-induced changes formed in the genome of survived germ cells lead to increased genome instability in the somatic cells of the progeny in animals and humans. This inheritable genome instability may cause a decrease in the quality of human health

  15. Working memory load improves early stages of independent visual processing

    OpenAIRE

    Cocchi, Luca; Toepel, Ulrike; De Lucia, Marzia; Martuzzi, Roberto; Wood, Stephen J.; Carter, Olivia; Murray, Micah M.

    2010-01-01

    Increasing evidence suggests that working memory and perceptual processes are dynamically interrelated due to modulating activity in overlapping brain networks. However, the direct influence of working memory on the spatio-temporal brain dynamics of behaviorally relevant intervening information remains unclear. To investigate this issue, subjects performed a visual proximity grid perception task under three different visual-spatial working memory (VSWM) load conditions. VSWM load was manipula...

  16. Modern elevator drives - aspects for planners and architects; Moderne Aufzugsantriebe - Aspekte fuer Planer und Architekten

    Energy Technology Data Exchange (ETDEWEB)

    Kirchenmayer, G. [Ziel-Abegg GmbH und Co. KG, Kuenzelsau (Germany)

    1997-04-01

    Elevators are destined for the vertical haulage of persons and loads. With passenger elevators, comfort is a major aspect. Passengers must not be inconvenienced by jerky lift movements or noise. A further criterion is energy demand. Energy consumption may vary, depending on the type of drive. (orig.) [Deutsch] Der Aufzug hat die Aufgabe, Personen und Lasten senkrecht zu befoerdern. Bei Personenaufzuegen wird grosser Wert auf Fahrkomfort gelegt. Waehrend der Fahrt sollen sich die Fahrgaeste moeglichst ohne ruckartige Aufzugsbewegungen und ohne Geraeuschbelaestigung wohlfuehlen. Der Energiebedarf ist ebenfalls von Bedeutung. Je nach Art des Antriebes ist der Energieverbrauch unterschiedlich. (orig.)

  17. Requirements on the mechanical design of reactor systems operating at elevated temperature

    International Nuclear Information System (INIS)

    Schulz, H.; Glahn, M.

    1979-01-01

    The paper presents the contemporary status of the requirements on the mechanical design and analysis developed during the licensing procedure of reactor systems operating at elevated temperature. General requirements for the design at elevated temperature are reviewed. The main proposal is to point out some limit strain criteria which are not included in present design guidelines and codes. The developed strain criteria are used to limit the component deformations in case of power excursions like the Bethe-Tait accident. It is also applicable for loads arising from other faulted conditions. (orig.)

  18. Nutrient and Coliform Loading (NCL)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This is a database of available fecal coliform bacteria, fecal streptococci bacteria, and nutrient loading data. Loading for contaminants other than fecal coliform...

  19. Implementation of Remaining Useful Lifetime Transformer Models in the Fleet-Wide Prognostic and Health Management Suite

    International Nuclear Information System (INIS)

    Agarwal, Vivek; Lybeck, Nancy J.; Pham, Binh; Rusaw, Richard; Bickford, Randall

    2015-01-01

    Research and development efforts are required to address aging and reliability concerns of the existing fleet of nuclear power plants. As most plants continue to operate beyond the license life (i.e., towards 60 or 80 years), plant components are more likely to incur age-related degradation mechanisms. To assess and manage the health of aging plant assets across the nuclear industry, the Electric Power Research Institute has developed a web-based Fleet-Wide Prognostic and Health Management (FW-PHM) Suite for diagnosis and prognosis. FW-PHM is a set of web-based diagnostic and prognostic tools and databases, comprised of the Diagnostic Advisor, the Asset Fault Signature Database, the Remaining Useful Life Advisor, and the Remaining Useful Life Database, that serves as an integrated health monitoring architecture. The main focus of this paper is the implementation of prognostic models for generator step-up transformers in the FW-PHM Suite. One prognostic model discussed is based on the functional relationship between degree of polymerization, (the most commonly used metrics to assess the health of the winding insulation in a transformer) and furfural concentration in the insulating oil. The other model is based on thermal-induced degradation of the transformer insulation. By utilizing transformer loading information, established thermal models are used to estimate the hot spot temperature inside the transformer winding. Both models are implemented in the Remaining Useful Life Database of the FW-PHM Suite. The Remaining Useful Life Advisor utilizes the implemented prognostic models to estimate the remaining useful life of the paper winding insulation in the transformer based on actual oil testing and operational data.

  20. Cognitive Load and Strategic Sophistication

    OpenAIRE

    Allred, Sarah; Duffy, Sean; Smith, John

    2013-01-01

    We study the relationship between the cognitive load manipulation and strategic sophistication. The cognitive load manipulation is designed to reduce the subject's cognitive resources that are available for deliberation on a choice. In our experiment, subjects are placed under a large cognitive load (given a difficult number to remember) or a low cognitive load (given a number which is not difficult to remember). Subsequently, the subjects play a one-shot game then they are asked to recall...

  1. Research of Impact Load in Large Electrohydraulic Load Simulator

    Directory of Open Access Journals (Sweden)

    Yongguang Liu

    2014-01-01

    Full Text Available The stronger impact load will appear in the initial phase when the large electric cylinder is tested in the hardware-in-loop simulation. In this paper, the mathematical model is built based on AMESim, and then the reason of the impact load is investigated through analyzing the changing tendency of parameters in the simulation results. The inhibition methods of impact load are presented according to the structural invariability principle and applied to the actual system. The final experimental result indicates that the impact load is inhibited, which provides a good experimental condition for the electric cylinder and promotes the study of large load simulator.

  2. Demand Response Load Following of Source and Load Systems

    DEFF Research Database (Denmark)

    Hu, Jianqiang; Cao, Jinde; Yong, Taiyou

    2017-01-01

    This paper presents a demand response load following strategy for an interconnected source and load system, in which we utilize traditional units and population of cooling thermostatically controlled loads (TCLs) to follow the mismatched power caused by the load activities and the renewable power...... injection in real time. In the demand side of power systems, these TCLs are often affiliated to a bus load agent and can be aggregated to multiple TCL aggregators. Firstly, aggregate evaluation of the TCL aggregator is carried out based on a bilinear aggregate model so as to derive the available regulation...

  3. Gearbox Fatigue Load Estimation for Condition Monitoring of Wind Turbines

    DEFF Research Database (Denmark)

    Perisic, Nevena; Pedersen, Bo Juul; Kirkegaard, Poul Henning

    2012-01-01

    control and data acquisition (SCADA) system. Estimated loads can be further used for prediction of remaining operating lifetime of turbine components, detection of high stress level or fault detection. An augmented Kalman filter is chosen as the fatigue load estimator because its characteristics well suit......The focus of the paper is on a design of a fatigue load estimator for predictive condition monitoring systems (CMS) of wind turbines. In order to avoid high-price measurement equipment required for direct load measuring, an indirect approach is suggested using only measurements from supervisory...... for the real time application. This paper presents results of the estimation of the gearbox fatigue load, often called shaft torque, using simulated data of wind turbine. Noise sensitivity of the algorithm is investigated by assuming different levels of measurement noise. Shaft torque estimations are compared...

  4. Elevated tumour marker: an indication for imaging?

    LENUS (Irish Health Repository)

    McMahon, Colm J

    2012-02-01

    INTRODUCTION: The purpose of this study was to evaluate the utility of imaging examinations in patients with elevated tumour markers when (a) the tumour marker is not validated for as a primary diagnostic test; (b) the patient had no personal history of cancer and (c) the patient had no other imaging indication. MATERIALS AND METHODS: Patients without known cancer who had abnormal carcinoembryonic antigen, CA19-9, CA125 and\\/or CA15-3 serology over a one-year period were included. A retrospective medical record review was performed to assess the number of these cases who underwent imaging because of \\'elevated tumour marker\\' in the absence of a clinical indication for imaging. The number and result of these imaging studies were evaluated. RESULTS: Eight hundred and nineteen patients were included. Of those, 25 patients (mean age: 67.8 [range 41-91] y), were imaged to evaluate: \\'elevated tumour marker\\'. They underwent 29 imaging studies (mean [+\\/-standard deviation (SD)] per patient = 1.2 [+\\/-0.4]), and had 42 elevated tumour marker serology tests (mean [+\\/-SD] per patient = 1.7 [+\\/-0.7]). Four patients had >1 imaging test. No patient had an imaging study which diagnosed a malignancy or explained the elevated tumour marker. CONCLUSION: The non-judicious use of tumour markers can prompt further unnecessary investigations including imaging. In this study, there was no positive diagnostic yield for imaging performed for investigation of \\'elevated tumour marker\\'. \\'Elevated tumour marker\\

  5. Load Estimation from Modal Parameters

    DEFF Research Database (Denmark)

    Aenlle, Manuel López; Brincker, Rune; Fernández, Pelayo Fernández

    2007-01-01

    In Natural Input Modal Analysis the modal parameters are estimated just from the responses while the loading is not recorded. However, engineers are sometimes interested in knowing some features of the loading acting on a structure. In this paper, a procedure to determine the loading from a FRF m...

  6. ST Elevations and Elevated Cardiac Enzymes Not Always a STEMI: Two Case Reports.

    Science.gov (United States)

    Fernández Fernández, Juan; Deliz-Guzmán, Claudia; Andino-Colón, César; Claudio-Hernández, Héctor; Lugo-Amador, Nannette

    2016-01-01

    Chest pain is a common complaint in the emergency department (ED). Besides a careful history and physical exam; electrocardiogram, laboratory tests and imaging studies are widely available diagnostic tests that are used for patient assessment. When ST elevation and elevated cardiac enzymes are present the most likely diagnosis are ST elevation myocardial infarction (STEMI) or myocarditis. In this case report we present two low risk patients for major adverse cardiac event with ST elevation and elevated cardiac enzymes and how a careful risk assessment and detailed electrocardiogram evaluation could help differentiating between these two diagnoses.

  7. High loading uranium plate

    International Nuclear Information System (INIS)

    Wiencek, T.C.; Domagala, R.F.; Thresh, H.R.

    1990-01-01

    Two embodiments of a high uranium fuel plate are disclosed which contain a meat comprising structured uranium compound confined between a pari of diffusion bonded ductile metal cladding plates uniformly covering the meat, the meat hiving a uniform high fuel loading comprising a content of uranium compound greater than about 45 Vol. % at a porosity not greater than about 10 Vol. %. In a first embodiment, the meat is a plurality of parallel wires of uranium compound. In a second embodiment, the meat is a dispersion compact containing uranium compound. The fuel plates are fabricated by a hot isostatic pressing process

  8. Android Fully Loaded

    CERN Document Server

    Huddleston, Rob

    2012-01-01

    Fully loaded with the latest tricks and tips on your new Android! Android smartphones are so hot, they're soaring past iPhones on the sales charts. And the second edition of this muscular little book is equally impressive--it's packed with tips and tricks for getting the very most out of your latest-generation Android device. Start Facebooking and tweeting with your Android mobile, scan barcodes to get pricing and product reviews, download your favorite TV shows--the book is positively bursting with practical and fun how-tos. Topics run the gamut from using speech recognition, location-based m

  9. Spreading the load

    International Nuclear Information System (INIS)

    Hay, Greg

    1999-01-01

    This article examines the management of power demand by the regional electricity companies in the United Kingdom so that consumers use most power at times when the pool price is at its lowest. The use of teleswitching for load management, the control of the heating of large residential buildings, the power demand of supermarkets with 24hr opening, financial incentives, and the forecasting of demand are discussed. Details are given of the work of the operational forecasting team, and the matching of demand with generators availability by the scheduling team of the National Grid. (UK)

  10. Spatial electric load forecasting

    CERN Document Server

    Willis, H Lee

    2002-01-01

    Containing 12 new chapters, this second edition contains offers increased-coverage of weather correction and normalization of forecasts, anticipation of redevelopment, determining the validity of announced developments, and minimizing risk from over- or under-planning. It provides specific examples and detailed explanations of key points to consider for both standard and unusual utility forecasting situations, information on new algorithms and concepts in forecasting, a review of forecasting pitfalls and mistakes, case studies depicting challenging forecast environments, and load models illustrating various types of demand.

  11. Soil load above Hanford waste storage tanks (2 volumes)

    International Nuclear Information System (INIS)

    Pianka, E.W.

    1995-01-01

    This document is a compilation of work performed as part of the Dome Load Control Project in 1994. Section 2 contains the calculations of the weight of the soil over the tank dome for each of the 75-feet-diameter waste-storage tanks located at the Hanford Site. The chosen soil specific weight and soil depth measured at the apex of the dome crown are the same as those used in the primary analysis that qualified the design. Section 3 provides reference dimensions for each of the tank farm sites. The reference dimensions spatially orient the tanks and provide an outer diameter for each tank. Section 4 summarizes the available soil surface elevation data. It also provides examples of the calculations performed to establish the present soil elevation estimates. The survey data and other data sources from which the elevation data has been obtained are printed separately in Volume 2 of this Supporting Document. Section 5 contains tables that provide an overall summary of the present status of dome loads. Tables summarizing the load state corresponding to the soil depth and soil specific weight for the original qualification analysis, the gravity load requalification for soil depth and soil specific weight greater than the expected actual values, and a best estimate condition of soil depth and specific weight are presented for the Double-Shell Tanks. For the Single-Shell Tanks, only the original qualification analysis is available; thus, the tabulated results are for this case only. Section 6 provides a brief overview of past analysis and testing results that given an indication of the load capacity of the waste storage tanks that corresponds to a condition approaching ultimate failure of the tank. 31 refs

  12. Dorzolamide Loaded Niosomal Vesicles: Comparison of Passive and Remote Loading Methods

    OpenAIRE

    Hashemi Dehaghi, Mohadeseh; Haeri, Azadeh; Keshvari, Hamid; Abbasian, Zahra; Dadashzadeh, Simin

    2017-01-01

    Glaucoma is a common progressive eye disorder and the treatment strategies will benefit from nanoparticulate delivery systems with high drug loading and sustained delivery of intraocular pressure lowering agents. Niosomes have been reported as a novel approach to improve drug low corneal penetration and bioavailability characteristics. Along with this, poor entrapment efficiency of hydrophilic drug in niosomal formulation remains as a major formulation challenge. Taking this perspective into ...

  13. Computation of shakedown loads feasibility study

    International Nuclear Information System (INIS)

    Save, M.; Saxce, G. de; Borkowski, A.

    1991-01-01

    Structures submitted to variable loads and temperature fields may enter in a regime of ratcheting where strains and hence structural deflections increase cycle by cycle. It is important to demonstrate that ratcheting is avoided. This happens of course if the structure remains entirely in the elastic regime. However, for more severe loadings, plastic deformations occur and the analyst must then demonstrate that the structure shakes down or adapts. Shakedown may be elastic if after a transient period all strain variations become elastic, or plastic when alternating plasticity occurs. This report addresses plastic shakedown. The problem is treated from the theoretical point of view but also - and this is a very important part of the work - from the numerical and software point of view

  14. Dynamic stability under sudden loads

    International Nuclear Information System (INIS)

    Simitses, G.J.

    1998-01-01

    The concept of dynamic stability of elastic structures subjected to sudden (step) loads is discussed. The various criteria and related methodologies for estimating critical conditions are presented with the emphasis on their similarities and differences. These are demonstrated by employing a simple mechanical model. Several structural configurations are analyzed, for demonstration purposes, with the intention of comparing critical dynamic loads to critical static loads. These configurations include shallow arches and shallow spherical caps, two bar frames, and imperfect cylindrical shells of metallic as well as laminated composite construction. In the demonstration examples, the effect of static pre loading on the dynamic critical load is presented

  15. Burst pressure of super duplex stainless steel pipes subject to combined axial tension, internal pressure and elevated temperature

    International Nuclear Information System (INIS)

    Lasebikan, B.A.; Akisanya, A.R.

    2014-01-01

    The burst pressure of super duplex stainless steel pipe is measured under combined internal pressure, external axial tension and elevated temperature up to 160 °C. The experimental results are compared with existing burst pressure prediction models. Existing models are found to provide reasonable estimate of the burst pressure at room temperature but significantly over estimate the burst pressure at elevated temperature. Increasing externally applied axial stress and elevated temperature reduces the pressure capacity. - Highlights: • The burst pressure of super duplex steel is measured under combined loading. • Effect of elevated temperature on burst pressure is determined. • Burst pressure decreases with increasing temperature. • Existing models are reliable at room temperature. • Burst strength at elevated temperature is lower than predictions

  16. Load Control System Reliability

    Energy Technology Data Exchange (ETDEWEB)

    Trudnowski, Daniel [Montana Tech of the Univ. of Montana, Butte, MT (United States)

    2015-04-03

    This report summarizes the results of the Load Control System Reliability project (DOE Award DE-FC26-06NT42750). The original grant was awarded to Montana Tech April 2006. Follow-on DOE awards and expansions to the project scope occurred August 2007, January 2009, April 2011, and April 2013. In addition to the DOE monies, the project also consisted of matching funds from the states of Montana and Wyoming. Project participants included Montana Tech; the University of Wyoming; Montana State University; NorthWestern Energy, Inc., and MSE. Research focused on two areas: real-time power-system load control methodologies; and, power-system measurement-based stability-assessment operation and control tools. The majority of effort was focused on area 2. Results from the research includes: development of fundamental power-system dynamic concepts, control schemes, and signal-processing algorithms; many papers (including two prize papers) in leading journals and conferences and leadership of IEEE activities; one patent; participation in major actual-system testing in the western North American power system; prototype power-system operation and control software installed and tested at three major North American control centers; and, the incubation of a new commercial-grade operation and control software tool. Work under this grant certainly supported the DOE-OE goals in the area of “Real Time Grid Reliability Management.”

  17. Thermal Behavior of Cylindrical Buckling Restrained Braces at Elevated Temperatures

    Directory of Open Access Journals (Sweden)

    Elnaz Talebi

    2014-01-01

    Full Text Available The primary focus of this investigation was to analyze sequentially coupled nonlinear thermal stress, using a three-dimensional model. It was meant to shed light on the behavior of Buckling Restraint Brace (BRB elements with circular cross section, at elevated temperature. Such bracing systems were comprised of a cylindrical steel core encased in a strong concrete-filled steel hollow casing. A debonding agent was rubbed on the core’s surface to avoid shear stress transition to the restraining system. The numerical model was verified by the analytical solutions developed by the other researchers. Performance of BRB system under seismic loading at ambient temperature has been well documented. However, its performance in case of fire has yet to be explored. This study showed that the failure of brace may be attributed to material strength reduction and high compressive forces, both due to temperature rise. Furthermore, limiting temperatures in the linear behavior of steel casing and concrete in BRB element for both numerical and analytical simulations were about 196°C and 225°C, respectively. Finally it is concluded that the performance of BRB at elevated temperatures was the same as that seen at room temperature; that is, the steel core yields prior to the restraining system.

  18. Thermal behavior of cylindrical buckling restrained braces at elevated temperatures.

    Science.gov (United States)

    Talebi, Elnaz; Tahir, Mahmood Md; Zahmatkesh, Farshad; Yasreen, Airil; Mirza, Jahangir

    2014-01-01

    The primary focus of this investigation was to analyze sequentially coupled nonlinear thermal stress, using a three-dimensional model. It was meant to shed light on the behavior of Buckling Restraint Brace (BRB) elements with circular cross section, at elevated temperature. Such bracing systems were comprised of a cylindrical steel core encased in a strong concrete-filled steel hollow casing. A debonding agent was rubbed on the core's surface to avoid shear stress transition to the restraining system. The numerical model was verified by the analytical solutions developed by the other researchers. Performance of BRB system under seismic loading at ambient temperature has been well documented. However, its performance in case of fire has yet to be explored. This study showed that the failure of brace may be attributed to material strength reduction and high compressive forces, both due to temperature rise. Furthermore, limiting temperatures in the linear behavior of steel casing and concrete in BRB element for both numerical and analytical simulations were about 196°C and 225°C, respectively. Finally it is concluded that the performance of BRB at elevated temperatures was the same as that seen at room temperature; that is, the steel core yields prior to the restraining system.

  19. Properties of Free-Machining Aluminum Alloys at Elevated Temperatures

    Science.gov (United States)

    Faltus, Jiří; Karlík, Miroslav; Haušild, Petr

    In areas close to the cutting tool the workpieces being dry machined could be heated up to 350°C and they may be impact loaded. Therefore it is of interest to study mechanical properties of corresponding materials at elevated temperatures. Free-machining alloys of Al-Cu and Al-Mg-Si systems containing Pb, Bi and Sn additions (AA2011, AA2111B, AA6262, and AA6023) were subjected to Charpy U notch impact test at the temperatures ranging from 20 to 350°C. The tested alloys show a sharp drop in notch impact strength KU at different temperatures. This drop of KU is caused by liquid metal embrittlement due to the melting of low-melting point dispersed phases which is documented by differential scanning calorimetry. Fracture surfaces of the specimens were observed using a scanning electron microscope. At room temperature, the fractures of all studied alloys exhibited similar ductile dimple fracture micromorphology, at elevated temperatures, numerous secondary intergranular cracks were observed.

  20. Surface instabilities in shock loaded granular media

    Science.gov (United States)

    Kandan, K.; Khaderi, S. N.; Wadley, H. N. G.; Deshpande, V. S.

    2017-12-01

    The initiation and growth of instabilities in granular materials loaded by air shock waves are investigated via shock-tube experiments and numerical calculations. Three types of granular media, dry sand, water-saturated sand and a granular solid comprising PTFE spheres were experimentally investigated by air shock loading slugs of these materials in a transparent shock tube. Under all shock pressures considered here, the free-standing dry sand slugs remained stable while the shock loaded surface of the water-saturated sand slug became unstable resulting in mixing of the shocked air and the granular material. By contrast, the PTFE slugs were stable at low pressures but displayed instabilities similar to the water-saturated sand slugs at higher shock pressures. The distal surfaces of the slugs remained stable under all conditions considered here. Eulerian fluid/solid interaction calculations, with the granular material modelled as a Drucker-Prager solid, reproduced the onset of the instabilities as seen in the experiments to a high level of accuracy. These calculations showed that the shock pressures to initiate instabilities increased with increasing material friction and decreasing yield strain. Moreover, the high Atwood number for this problem implied that fluid/solid interaction effects were small, and the initiation of the instability is adequately captured by directly applying a pressure on the slug surface. Lagrangian calculations with the directly applied pressures demonstrated that the instability was caused by spatial pressure gradients created by initial surface perturbations. Surface instabilities are also shown to exist in shock loaded rear-supported granular slugs: these experiments and calculations are used to infer the velocity that free-standing slugs need to acquire to initiate instabilities on their front surfaces. The results presented here, while in an idealised one-dimensional setting, provide physical understanding of the conditions required to

  1. Keauhou, Hawaii Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  2. Atka, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  3. King Cove, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  4. Chenega, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  5. Juneau, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  6. Lahaina, Hawaii Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  7. Kawaihae, Hawaii Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  8. Shaded Relief of Minnesota Elevation - Color

    Data.gov (United States)

    Minnesota Department of Natural Resources — This file is a product of a shaded relief process on the 30 meter resolution Digital Elevation Model data (dem30im3). This image was created using a custom AML...

  9. Shaded Relief of Minnesota Elevation - Black & White

    Data.gov (United States)

    Minnesota Department of Natural Resources — This file is a product of a shaded relief process on the 30 meter resolution Digital Elevation Model data (dem30im3). This image was created using a custom AML...

  10. Tatitlek, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  11. Hoonah, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  12. Whittier, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  13. Gustavus, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  14. Taholah, Washington Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  15. Chignik, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  16. Panama City, Florida Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  17. Mariana Trench Bathymetric Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) created a bathymetric digital elevation model (DEM) for the Mariana Trench and adjacent seafloor in the Western...

  18. Nikolski, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  19. Battling against Marginalisation: Towards the Elevation of ...

    African Journals Online (AJOL)

    This paper questions the rationale of having Zimbabwean local languages and in ... The study adopts a qualitative methodology and a case study design to ... and possibly future intervention strategies of elevating indigenous languages.

  20. Elevator mechanism and method for scintillation detectors

    International Nuclear Information System (INIS)

    Frank, E.

    1975-01-01

    An elevator mechanism and method for raising and lowering radioactive samples through a shielded vertical counting chamber in a benchtop scintillation detector is described. The elevator mechanism adds little or nothing to the height of the detector by using an elongated flexible member such as a metal tape secured to the bottom of the elevator platform and extending downwardly through the counting chamber and its bottom shielding, where the tape is bent laterally for connection to a drive means. In the particular embodiment illustrated, the tape is bent laterally below the bottom shielding for the counting chamber, and then upwardly along or through one side of the shielding to a reel at the top of the shielding. The tape is wound onto the reel, and the reel is driven by a reversible motor which winds and unwinds the tape on the reel to raise and lower the elevator platform

  1. Elevated temperature erosive wear of metallic materials

    International Nuclear Information System (INIS)

    Roy, Manish

    2006-01-01

    Solid particle erosion of metals and alloys at elevated temperature is governed by the nature of the interaction between erosion and oxidation, which, in turn, is determined by the thickness, pliability, morphology, adhesion characteristics and toughness of the oxide scale. The main objective of this paper is to critically review the present state of understanding of the elevated temperature erosion behaviour of metals and alloys. First of all, the erosion testing at elevated temperature is reviewed. This is followed by discussion of the essential features of elevated temperature erosion with special emphasis on microscopic observation, giving details of the erosion-oxidation (E-O) interaction mechanisms. The E-O interaction has been elaborated in the subsequent section. The E-O interaction includes E-O maps, analysis of transition criteria from one erosion mechanism to another mechanism and quantification of enhanced oxidation kinetics during erosion. Finally, the relevant areas for future studies are indicated. (topical review)

  2. United States Interagency Elevation Inventory (USIEI)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The U.S. Interagency Elevation Inventory displays high-accuracy topographic and bathymetric data for the United States and its territories. The project is a...

  3. Monterey, California Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  4. Garibaldi, Oregon Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  5. ASTER Digital Elevation Model V003

    Data.gov (United States)

    National Aeronautics and Space Administration — The ASTER Digital Elevation Model (DEM) product is generated using bands 3N (nadir-viewing) and 3B (backward-viewing) of an ASTER Level-1A image acquired by the...

  6. Hanalei, Hawaii Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  7. Ocean City, Maryland Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  8. Southeast Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  9. Kachemak Bay, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  10. New Orleans, Louisiana Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions in the Gulf of Mexico....

  11. Virginia Beach, Virginia Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  12. Galveston, Texas Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  13. Savannah, Georgia Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  14. Biloxi, Mississippi Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  15. Puerto Rico Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  16. Santa Barbara, California Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  17. Hilo, Hawaii Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  18. Corpus Christi, Texas Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  19. Port Alexander Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  20. Grain Elevators: New Source Performance Standards (NSPS)

    Science.gov (United States)

    The New Source Performance Standards (NSPS) for Grain Elevators aims to reduce particulate matter pollution. The new amendments seek to clarify definitions, and requirements, as well as propose new regulations on particulate matter emissions

  1. 77 FR 21471 - Final Flood Elevation Determinations

    Science.gov (United States)

    2012-04-10

    ... elevations have been published in newspapers of local circulation and ninety (90) days have elapsed since... School Creek. Approximately 0.61 mile +605 upstream of the confluence with School Creek. Arkansas River...

  2. Arecibo, Puerto Rico Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  3. Craig, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  4. Midway Atoll Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  5. Guayama, Puerto Rico Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  6. Fajardo, Puerto Rico Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  7. Montauk, New York Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  8. Sand Point, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  9. Shemya, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  10. La Push, Washington Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  11. Portland, Maine Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  12. Arena Cove, California Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  13. Port Orford, Oregon Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  14. An elevator for cobalt-60 source

    International Nuclear Information System (INIS)

    Tang Zaimin; Liang Donghu

    1990-07-01

    The elevator used for cobalt-60 source is a key device in the irradiation industry. It plays an important role in the safety and control of irradiation operation as well as the utilization rate of radiation source. From 1983 to 1986, Beijing Institute of Nuclear Engineering undertook designing of various size irradiation projects for different uses. Since then a kind of cobalt-60 source elevator suited for the irradiator of wet-source-storage has been chosen. It is reliable in the operation and complete in the function. An automatic control circuit brings the systems of cobalt-60 source elevator into an interlock system which ensures the irradiation operation safety. Besides introducing the structural features and performance of this elevator, the conditions of safety interlocking in raising or lowering the cobalt-60 source is also discussed. The discussion is from the safety viewpoint of operating an irradiator and irradiation technology

  15. 2 minute Southcentral Alaska Elevation Grid

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The 2-minute Southcentral Alaska Elevation Grid provides bathymetric data in ASCII raster format of 2-minute resolution in geographic coordinates. This grid is...

  16. Adak, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  17. Dutch Harbor, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  18. Unalaska, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) to support individual coastal States as part of the...

  19. Ponce, Puerto Rico Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  20. ASTER Global Digital Elevation Model V002

    Data.gov (United States)

    National Aeronautics and Space Administration — The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) Global Digital Elevation Model (GDEM) was developed jointly by the U.S. National...