Load-induced modulation of signal transduction networks.

Science.gov (United States)

Jiang, Peng; Ventura, Alejandra C; Sontag, Eduardo D; Merajver, Sofia D; Ninfa, Alexander J; Del Vecchio, Domitilla

2011-10-11

Biological signal transduction networks are commonly viewed as circuits that pass along information--in the process amplifying signals, enhancing sensitivity, or performing other signal-processing tasks--to transcriptional and other components. Here, we report on a "reverse-causality" phenomenon, which we call load-induced modulation. Through a combination of analytical and experimental tools, we discovered that signaling was modulated, in a surprising way, by downstream targets that receive the signal and, in doing so, apply what in physics is called a load. Specifically, we found that non-intuitive changes in response dynamics occurred for a covalent modification cycle when load was present. Loading altered the response time of a system, depending on whether the activity of one of the enzymes was maximal and the other was operating at its minimal rate or whether both enzymes were operating at submaximal rates. These two conditions, which we call "limit regime" and "intermediate regime," were associated with increased or decreased response times, respectively. The bandwidth, the range of frequency in which the system can process information, decreased in the presence of load, suggesting that downstream targets participate in establishing a balance between noise-filtering capabilities and a circuit's ability to process high-frequency stimulation. Nodes in a signaling network are not independent relay devices, but rather are modulated by their downstream targets.

Mild wear modeling in the boundary lubrication regime

NARCIS (Netherlands)

Bosman, Rob

2011-01-01

Currently, the increasing demand for smaller and more efficient systems is increasing the stress put on interacting components. This forces components to operate in the boundary lubrication regime. In this lubrication regime, the normal load put on the components is no longer carried by the

Testing of Laterally Loaded Rigid Piles with Applied Overburden Pressure

DEFF Research Database (Denmark)

Sørensen, Søren Peder Hyldal; Foglia, Aligi; Ibsen, Lars Bo

2012-01-01

Small-scale tests have been conducted for the purpose of investigating the quasi-static behaviour of laterally loaded, non-slender piles installed in cohesionless soil. For that purpose, a new and innovative test setup has been developed. The tests have been conducted in a pressure tank...... such that it was possible to apply an overburden pressure to the soil. Hereby, the traditional uncertainties related to low effective stresses for small-scale tests has been avoided. A scaling law for laterally loaded piles has been proposed based on dimensional analysis. The novel testing method has been validated against...... the test results by means of the scaling law....

Testing of Laterally Loaded Rigid Piles with Applied Overburden Pressure

DEFF Research Database (Denmark)

Sørensen, Søren Peder Hyldal; Ibsen, Lars Bo; Foglia, Aligi

2015-01-01

Small-scale tests have been conducted to investigate the quasi-static behaviour of laterally loaded, non-slender piles installed in cohesionless soil. For that purpose, a new and innovative test setup has been developed. The tests have been conducted in a pressure tank such that it was possible...... to apply an overburden pressure to the soil. As a result of that, the traditional uncertainties related to low effective stresses for small-scale tests have been avoided. A normalisation criterion for laterally loaded piles has been proposed based on dimensional analysis. The test results using the novel...... testing method have been compared with the use of the normalisation criterion....

Upregulation of matrix synthesis in chondrocyte-seeded agarose following sustained bi-axial cyclic loading

Directory of Open Access Journals (Sweden)

Belinda Pingguan-Murphy

2012-08-01

Full Text Available OBJECTIVES: The promotion of extracellular matrix synthesis by chondrocytes is a requisite part of an effective cartilage tissue engineering strategy. The aim of this in vitro study was to determine the effect of bi-axial cyclic mechanical loading on cell proliferation and the synthesis of glycosaminoglycans by chondrocytes in threedimensional cultures. METHOD: A strain comprising 10% direct compression and 1% compressive shear was applied to bovine chondrocytes seeded in an agarose gel during two 12-hour conditioning periods separated by a 12-hour resting period. RESULTS: The bi-axial-loaded chondrocytes demonstrated a significant increase in glycosaminoglycan synthesis compared with samples exposed to uni-axial or no loading over the same period (p<0.05. The use of a free-swelling recovery period prior to the loading regime resulted in additional glycosaminoglycan production and a significant increase in DNA content (p<0.05, indicating cell proliferation. CONCLUSIONS: These results demonstrate that the use of a bi-axial loading regime results in increased matrix production compared with uni-axial loading.

Minimizing Load Effects on NA4 Gear Vibration Diagnostic Parameter

Science.gov (United States)

Dempsey, Paula J.; Zakrajsek, James J.

2001-01-01

NA4 is a vibration diagnostic parameter, developed by researchers at NASA Glenn Research Center, for health monitoring of gears in helicopter transmissions. The NA4 reacts to the onset of gear pitting damage and continues to react to the damage as it spreads. This research also indicates NA4 reacts similarly to load variations. The sensitivity of NA4 to load changes will substantially affect its performance on a helicopter gearbox that experiences continuously changing load throughout its flight regimes. The parameter NA4 has been used to monitor gear fatigue tests at constant load. At constant load, NA4 effectively detects the onset of pitting damage and tracks damage severity. Previous research also shows that NA4 reacts to changes in load applied to the gears in the same way it reacts to the onset of pitting damage. The method used to calculate NA4 was modified to minimize these load effects. The modified NA4 parameter was applied to four sets of experimental data. Results indicate the modified NA4 is no longer sensitive to load changes, but remains sensitive to pitting damage.

Macro-grazer herbivory regulates seagrass response to pulse and press nutrient loading.

Science.gov (United States)

Ravaglioli, Chiara; Capocchi, Antonella; Fontanini, Debora; Mori, Giovanna; Nuccio, Caterina; Bulleri, Fabio

2018-05-01

Coastal ecosystems are exposed to multiple stressors. Predicting their outcomes is complicated by variations in their temporal regimes. Here, by means of a 16-month experiment, we investigated tolerance and resistance traits of Posidonia oceanica to herbivore damage under different regimes of nutrient loading. Chronic and pulse nutrient supply were combined with simulated fish herbivory, treated as a pulse stressor. At ambient nutrient levels, P. oceanica could cope with severe herbivory, likely through an increase in photosynthetic activity. Elevated nutrient levels, regardless of the temporal regime, negatively affected plant growth and increased leaf nutritional quality. This ultimately resulted in a reduction of plant biomass that was particularly severe under chronic fertilization. Our results suggest that both chronic and pulse nutrient loadings increase plant palatability to macro-grazers. Strategies for seagrass management should not be exclusively applied in areas exposed to chronic fertilization since even short-term nutrient pulses could alter seagrass meadows. Copyright © 2018 Elsevier Ltd. All rights reserved.

Compressed magnetic flux amplifier with capacitive load

International Nuclear Information System (INIS)

Stuetzer, O.M.

1980-03-01

A first-order analysis is presented for a compressed magnetic flux (CMF) current amplifier working into a load with a capacitive component. Since the purpose of the investigation was to gain a general understanding of the arrangement, a number of approximations and limitations were accepted. The inductance of the transducer varies with time; the inductance/resistance/capacitance (LRC) circuit therefore is parametric and solutions are different for the stable regime (high C), the oscillation regime (low C), and the transition case. Solutions and performance depend strongly on circuit boundary conditions, i.e., energization of the circuit by either an injected current or by an applied capacitor charge. The behavior of current and energy amplification for the various cases are discussed in detail. A number of experiments with small CMF devices showed that the first-order theory presented predicts transducer performance well in the linear regime

Kissinger method applied to the crystallization of glass-forming liquids: Regimes revealed by ultra-fast-heating calorimetry

Energy Technology Data Exchange (ETDEWEB)

Orava, J., E-mail: jo316@cam.ac.uk [Department of Materials Science & Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); WPI-Advanced Institute for Materials Research (WPI-AIMR), Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Greer, A.L., E-mail: alg13@cam.ac.uk [Department of Materials Science & Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); WPI-Advanced Institute for Materials Research (WPI-AIMR), Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan)

2015-03-10

Highlights: • Study of ultra-fast DSC applied to the crystallization of glass-forming liquids. • Numerical modeling of DSC traces at heating rates exceeding 10 orders of magnitude. • Identification of three regimes in Kissinger plots. • Elucidation of the effect of liquid fragility on the Kissinger method. • Modeling to study the regime in which crystal growth is thermodynamically limited. - Abstract: Numerical simulation of DSC traces is used to study the validity and limitations of the Kissinger method for determining the temperature dependence of the crystal-growth rate on continuous heating of glasses from the glass transition to the melting temperature. A particular interest is to use the wide range of heating rates accessible with ultra-fast DSC to study systems such as the chalcogenide Ge{sub 2}Sb{sub 2}Te{sub 5} for which fast crystallization is of practical interest in phase-change memory. Kissinger plots are found to show three regimes: (i) at low heating rates the plot is straight, (ii) at medium heating rates the plot is curved as expected from the liquid fragility, and (iii) at the highest heating rates the crystallization rate is thermodynamically limited, and the plot has curvature of the opposite sign. The relative importance of these regimes is identified for different glass-forming systems, considered in terms of the liquid fragility and the reduced glass-transition temperature. The extraction of quantitative information on fundamental crystallization kinetics from Kissinger plots is discussed.

Kissinger method applied to the crystallization of glass-forming liquids: Regimes revealed by ultra-fast-heating calorimetry

International Nuclear Information System (INIS)

Orava, J.; Greer, A.L.

2015-01-01

Highlights: • Study of ultra-fast DSC applied to the crystallization of glass-forming liquids. • Numerical modeling of DSC traces at heating rates exceeding 10 orders of magnitude. • Identification of three regimes in Kissinger plots. • Elucidation of the effect of liquid fragility on the Kissinger method. • Modeling to study the regime in which crystal growth is thermodynamically limited. - Abstract: Numerical simulation of DSC traces is used to study the validity and limitations of the Kissinger method for determining the temperature dependence of the crystal-growth rate on continuous heating of glasses from the glass transition to the melting temperature. A particular interest is to use the wide range of heating rates accessible with ultra-fast DSC to study systems such as the chalcogenide Ge 2 Sb 2 Te 5 for which fast crystallization is of practical interest in phase-change memory. Kissinger plots are found to show three regimes: (i) at low heating rates the plot is straight, (ii) at medium heating rates the plot is curved as expected from the liquid fragility, and (iii) at the highest heating rates the crystallization rate is thermodynamically limited, and the plot has curvature of the opposite sign. The relative importance of these regimes is identified for different glass-forming systems, considered in terms of the liquid fragility and the reduced glass-transition temperature. The extraction of quantitative information on fundamental crystallization kinetics from Kissinger plots is discussed

Active Boundary Layer Control on a Highly Loaded Turbine Exit Case Profile

Directory of Open Access Journals (Sweden)

Julia Kurz

2018-03-01

Full Text Available A highly loaded turbine exit guide vane with active boundary layer control was investigated experimentally in the High Speed Cascade Wind Tunnel at the University of the German Federal Armed Forces, Munich. The experiments include profile Mach number distributions, wake traverse measurements as well as boundary layer investigations with a flattened Pitot probe. Active boundary layer control by fluidic oscillators was applied to achieve improved performance in the low Reynolds number regime. Low solidity, which can be applied to reduce the number of blades, increases the risk of flow separation resulting in increased total pressure losses. Active boundary layer control is supposed to overcome these negative effects. The experiments show that active boundary layer control by fluidic oscillators is an appropriate way to suppress massive open separation bubbles in the low Reynolds number regime.

Physics Based Model for Cryogenic Chilldown and Loading. Part I: Algorithm

Science.gov (United States)

Luchinsky, Dmitry G.; Smelyanskiy, Vadim N.; Brown, Barbara

2014-01-01

We report the progress in the development of the physics based model for cryogenic chilldown and loading. The chilldown and loading is model as fully separated non-equilibrium two-phase flow of cryogenic fluid thermally coupled to the pipe walls. The solution follow closely nearly-implicit and semi-implicit algorithms developed for autonomous control of thermal-hydraulic systems developed by Idaho National Laboratory. A special attention is paid to the treatment of instabilities. The model is applied to the analysis of chilldown in rapid loading system developed at NASA-Kennedy Space Center. The nontrivial characteristic feature of the analyzed chilldown regime is its active control by dump valves. The numerical predictions are in reasonable agreement with the experimental time traces. The obtained results pave the way to the development of autonomous loading operation on the ground and space.

Characterization of potential fire regimes: applying landscape ecology to fire management in Mexico

Science.gov (United States)

Jardel, E.; Alvarado, E.; Perez-Salicrup, D.; Morfín-Rios, J.

2013-05-01

Knowledge and understanding of fire regimes is fundamental to design sound fire management practices. The high ecosystem diversity of Mexico offers a great challenge to characterize the fire regime variation at the landscape level. A conceptual model was developed considering the main factors controlling fire regimes: climate and vegetation cover. We classified landscape units combining bioclimatic zones from the Holdridge life-zone system and actual vegetation cover. Since bioclimatic conditions control primary productivity and biomass accumulation (potential fuel), each landscape unit was considered as a fuel bed with a particular fire intensity and behavior potential. Climate is also a determinant factor of post-fire recovery rates of fuel beds, and climate seasonality (length of the dry and wet seasons) influences fire probability (available fuel and ignition efficiency). These two factors influence potential fire frequency. Potential fire severity can be inferred from fire frequency, fire intensity and behavior, and vegetation composition and structure. Based in the conceptual model, an exhaustive literature review and expert opinion, we developed rules to assign a potential fire regime (PFR) defined by frequency, intensity and severity (i.e. fire regime) to each bioclimatic-vegetation landscape unit. Three groups and eight types of potential fire regimes were identified. In Group A are fire-prone ecosystems with frequent low severity surface fires in grasslands (PFR type I) or forests with long dry season (II) and infrequent high-severity fires in chaparral (III), wet temperate forests (IV, fire restricted by humidity), and dry temperate forests (V, fire restricted by fuel recovery rate). Group B includes fire-reluctant ecosystems with very infrequent or occasional mixed severity surface fires limited by moisture in tropical rain forests (VI) or fuel availability in seasonally dry tropical forests (VII). Group C and PFR VIII include fire-free environments

Regime identification in ASDEX Upgrade

International Nuclear Information System (INIS)

Giannone, L; Sips, A C C; Kardaun, O; Spreitler, F; Suttrop, W

2004-01-01

The ability to recognize the transition from the L-mode to the H-mode or from the H-mode to the improved H-mode reliably from a conveniently small number of measurements in real time is of increasing importance for machine control. Discriminant analysis has been applied to regime identification of plasma discharges in the ASDEX Upgrade tokamak. An observation consists of a set of plasma parameters averaged over a time slice in a discharge. The data set consists of all observations over different discharges and time slices. Discriminant analysis yields coefficients allowing the classification of a new observation. The results of a frequentist and a formal Bayesian approach to discriminant analysis are compared. With five plasma variables, a failure rate of 1.3% for predicting the L-mode and the H-mode confinement regime was achieved. With five plasma variables, a failure rate of 5.3% for predicting the H-mode and the improved H-mode confinement regime was achieved. The coefficients derived by discriminant analysis have been applied subsequently to discharges to illustrate the operation of regime identification in a real time control system

Effect of Uniaxial Tensile Cyclic Loading Regimes on Matrix Organization and Tenogenic Differentiation of Adipose-Derived Stem Cells Encapsulated within 3D Collagen Scaffolds

Directory of Open Access Journals (Sweden)

Gayathri Subramanian

2017-01-01

Full Text Available Adipose-derived mesenchymal stem cells have become a popular cell choice for tendon repair strategies due to their relative abundance, ease of isolation, and ability to differentiate into tenocytes. In this study, we investigated the solo effect of different uniaxial tensile strains and loading frequencies on the matrix directionality and tenogenic differentiation of adipose-derived stem cells encapsulated within three-dimensional collagen scaffolds. Samples loaded at 0%, 2%, 4%, and 6% strains and 0.1 Hz and 1 Hz frequencies for 2 hours/day over a 7-day period using a custom-built uniaxial tensile strain bioreactor were characterized in terms of matrix organization, cell viability, and musculoskeletal gene expression profiles. The results displayed that the collagen fibers of the loaded samples exhibited increased matrix directionality with an increase in strain values. Gene expression analyses demonstrated that ASC-encapsulated collagen scaffolds loaded at 2% strain and 0.1 Hz frequency showed significant increases in extracellular matrix genes and tenogenic differentiation markers. Importantly, no cross-differentiation potential to osteogenic, chondrogenic, and myogenic lineages was observed at 2% strain and 0.1 Hz frequency loading condition. Thus, 2% strain and 0.1 Hz frequency were identified as the appropriate mechanical loading regime to induce tenogenic differentiation of adipose-derived stem cells cultured in a three-dimensional environment.

Effect of Uniaxial Tensile Cyclic Loading Regimes on Matrix Organization and Tenogenic Differentiation of Adipose-Derived Stem Cells Encapsulated within 3D Collagen Scaffolds.

Science.gov (United States)

Subramanian, Gayathri; Stasuk, Alexander; Elsaadany, Mostafa; Yildirim-Ayan, Eda

2017-01-01

Adipose-derived mesenchymal stem cells have become a popular cell choice for tendon repair strategies due to their relative abundance, ease of isolation, and ability to differentiate into tenocytes. In this study, we investigated the solo effect of different uniaxial tensile strains and loading frequencies on the matrix directionality and tenogenic differentiation of adipose-derived stem cells encapsulated within three-dimensional collagen scaffolds. Samples loaded at 0%, 2%, 4%, and 6% strains and 0.1 Hz and 1 Hz frequencies for 2 hours/day over a 7-day period using a custom-built uniaxial tensile strain bioreactor were characterized in terms of matrix organization, cell viability, and musculoskeletal gene expression profiles. The results displayed that the collagen fibers of the loaded samples exhibited increased matrix directionality with an increase in strain values. Gene expression analyses demonstrated that ASC-encapsulated collagen scaffolds loaded at 2% strain and 0.1 Hz frequency showed significant increases in extracellular matrix genes and tenogenic differentiation markers. Importantly, no cross-differentiation potential to osteogenic, chondrogenic, and myogenic lineages was observed at 2% strain and 0.1 Hz frequency loading condition. Thus, 2% strain and 0.1 Hz frequency were identified as the appropriate mechanical loading regime to induce tenogenic differentiation of adipose-derived stem cells cultured in a three-dimensional environment.

Hydrological regulation drives regime shifts: evidence from paleolimnology and ecosystem modeling of a large shallow Chinese lake.

Science.gov (United States)

Kong, Xiangzhen; He, Qishuang; Yang, Bin; He, Wei; Xu, Fuliu; Janssen, Annette B G; Kuiper, Jan J; van Gerven, Luuk P A; Qin, Ning; Jiang, Yujiao; Liu, Wenxiu; Yang, Chen; Bai, Zelin; Zhang, Min; Kong, Fanxiang; Janse, Jan H; Mooij, Wolf M

2017-02-01

Quantitative evidence of sudden shifts in ecological structure and function in large shallow lakes is rare, even though they provide essential benefits to society. Such 'regime shifts' can be driven by human activities which degrade ecological stability including water level control (WLC) and nutrient loading. Interactions between WLC and nutrient loading on the long-term dynamics of shallow lake ecosystems are, however, often overlooked and largely underestimated, which has hampered the effectiveness of lake management. Here, we focus on a large shallow lake (Lake Chaohu) located in one of the most densely populated areas in China, the lower Yangtze River floodplain, which has undergone both WLC and increasing nutrient loading over the last several decades. We applied a novel methodology that combines consistent evidence from both paleolimnological records and ecosystem modeling to overcome the hurdle of data insufficiency and to unravel the drivers and underlying mechanisms in ecosystem dynamics. We identified the occurrence of two regime shifts: one in 1963, characterized by the abrupt disappearance of submerged vegetation, and another around 1980, with strong algal blooms being observed thereafter. Using model scenarios, we further disentangled the roles of WLC and nutrient loading, showing that the 1963 shift was predominantly triggered by WLC, whereas the shift ca. 1980 was attributed to aggravated nutrient loading. Our analysis also shows interactions between these two stressors. Compared to the dynamics driven by nutrient loading alone, WLC reduced the critical P loading and resulted in earlier disappearance of submerged vegetation and emergence of algal blooms by approximately 26 and 10 years, respectively. Overall, our study reveals the significant role of hydrological regulation in driving shallow lake ecosystem dynamics, and it highlights the urgency of using multi-objective management criteria that includes ecological sustainability perspectives when

Control of power distribution and the safety of a WWER-1000 reactor during operation in a load-following regime

International Nuclear Information System (INIS)

Filipchuk, E.V.; Dunaev, V.G.; Luk'yanets, I.A.; Potapenko, P.T.; Timokhin, E.S.; Voznesenskij, V.A.; Mitin, V.I.

1984-01-01

An important task in ensuring the operational safety of a nuclear power plant with a vessel-type water-cooled, water-moderated reactor is the development of algorithms for controlling power distribution in base-load and load-following regimes. The control strategy must ensure that the form of power distribution is maintained within the permissible limits in the case of situations presenting a nuclear hazard and of xenon fluctuations when there are variations in power output. The task of controlling power distribution can be broken down into an axial problem and a radial-azimuthal problem. For maintenance of the form of axial power distribution an algorithm of optimum fast-action control is proposed; for maintenance of the radial-azimuthal form, an algorithm of optimum (i.e. best) approximation to the given distribution of control. The two control problems are solved by using a single computerized procedure based on mathematical programming. The algorithms are designed for use in computerized control. The paper presents the results of algorithm simulation. The authors propose that in the first stage, activation of the control systems should involve the operator, who can view the sequence of actions on a display screen. (author)

Influence of applied load on wear behavior of C/C-Cu composites under electric current

Directory of Open Access Journals (Sweden)

Jian Yin

2017-04-01

Full Text Available Using carbon fiber needled fabrics with Cu-mesh and graphite powder as the preform, Cu mesh modified carbon/carbon(C/C-Cu composites were prepared by chemical vapor deposition (CVD with C3H6 and impregnation-carbonization (I/C with furan resin. C/C composites, as a comparison, were also prepared. Their microstructures and wear morphologies were observed by optical microscopy (OM and scanning electron microscope (SEM, respectively. Wear behavior of C/C and C/C-Cu composites under different applied loads were investigated on a pin-on-disc wear tester. The results show that Cu meshes are well dispersed and pyrolytic carbon is in rough laminar structure. Both C/C and C/C-Cu composites had good wear properties. The current-carrying capacity of C/C-Cu composites increases and the arc discharge is hindered as the applied load increases from 40 N to 80 N. Both C/C and C/C-Cu composites had good wear properties. The mass wear rate of C/C-Cu composites under 80 N was only 4.2% of that under 60 N. In addition, C/C-Cu composites represent different wear behaviors because wear mechanisms of arc erosion, abrasive wear, adhesive wear, and oxidative wear are changing under different applied loads.

Multi-Fluid Modeling of Low-Recycling Divertor Regimes

International Nuclear Information System (INIS)

Smirnov, R.D.; Pigarov, A.Y.; Krasheninnikov, S.I.; Rognlien, T.D.; Soukhanovskii, V.A.; Rensink, M.E.; Maingi, R.; Skinner, C.H.; Stotler, D.P.; Bell, R.E.; Kugel, H.W.

2010-01-01

The low-recycling regimes of divertor operation in a single-null NSTX magnetic configuration are studied using computer simulations with the edge plasma transport code UEDGE. The edge plasma transport properties pertinent to the low-recycling regimes are demonstrated. These include the flux-limited character of the parallel heat transport and the high plasma temperatures with the flattened profiles in the scrape-off-layer. It is shown that to maintain the balance of particle fluxes at the core interface the deuterium gas puffing rate should increase as the divertor recycling coefficient decreases. The radial profiles of the heat load to the outer divertor plate, the upstream radial plasma profiles, and the effects of the cross-field plasma transport in the low-recycling regimes are discussed. It is also shown that recycling of lithium impurities evaporating from the divertor plate at high surface temperatures can reverse the low-recycling divertor operational regime to the high-recycling one and may cause thermal instability of the divertor plate.

Formation of metal-F bonds during frictional sliding : Influence of water and applied load

NARCIS (Netherlands)

Shen, J. T.; Pei, Y. T.; De Hosson, J. Th. M.

2016-01-01

Effects of water lubrication and applied load on the formation of PTFE transfer films and metal-F bonds during sliding when PTFE filled composites sliding against steel and Al2O3 are investigated. In water lubricated conditions, XPS analysis reveals that a thin layer of water molecules at the

Terricolous alpine lichens are sensitive to both load and concentration of applied nitrogen and have potential as bioindicators of nitrogen deposition

International Nuclear Information System (INIS)

Britton, Andrea J.; Fisher, Julia M.

2010-01-01

The influence of applied nitrogen (N) concentration and load on thallus chemistry and growth of five terricolous alpine lichen species was investigated in a three-month N addition study. Thallus N content was influenced by both concentration and load; but the relative importance of these parameters varied between species. Growth was most affected by concentration. Thresholds for effects observed in this study support a low critical load for terricolous lichen communities ( -1 y -1 ) and suggest that concentrations of N currently encountered in UK cloudwater may have detrimental effects on the growth of sensitive species. The significance of N concentration effects on sensitive species also highlights the need to avoid artificially high concentrations when designing N addition experiments. Given the sensitivity of some species to extremely low loads and concentrations of N we suggest that terricolous lichens have potential as indicators of deposition and impact in northern and alpine ecosystems. - Terricolous lichen species' N content responds to both applied N concentration and load while applied N concentration has greatest effects on growth.

Terricolous alpine lichens are sensitive to both load and concentration of applied nitrogen and have potential as bioindicators of nitrogen deposition

Energy Technology Data Exchange (ETDEWEB)

Britton, Andrea J., E-mail: a.britton@macaulay.ac.u [Macaulay Land Use Research Institute, Craigiebuckler, Aberdeen AB15 8QH (United Kingdom); Fisher, Julia M. [Macaulay Land Use Research Institute, Craigiebuckler, Aberdeen AB15 8QH (United Kingdom)

2010-05-15

The influence of applied nitrogen (N) concentration and load on thallus chemistry and growth of five terricolous alpine lichen species was investigated in a three-month N addition study. Thallus N content was influenced by both concentration and load; but the relative importance of these parameters varied between species. Growth was most affected by concentration. Thresholds for effects observed in this study support a low critical load for terricolous lichen communities (<7.5 kg N ha{sup -1} y{sup -1}) and suggest that concentrations of N currently encountered in UK cloudwater may have detrimental effects on the growth of sensitive species. The significance of N concentration effects on sensitive species also highlights the need to avoid artificially high concentrations when designing N addition experiments. Given the sensitivity of some species to extremely low loads and concentrations of N we suggest that terricolous lichens have potential as indicators of deposition and impact in northern and alpine ecosystems. - Terricolous lichen species' N content responds to both applied N concentration and load while applied N concentration has greatest effects on growth.

A gravity loading countermeasure skinsuit

Science.gov (United States)

Waldie, James M.; Newman, Dava J.

2011-04-01

Despite the use of several countermeasures, significant physiological deconditioning still occurs during long duration spaceflight. Bone loss - primarily due to the absence of loading in microgravity - is perhaps the greatest challenge to resolve. This paper describes a conceptual Gravity Loading Countermeasure Skinsuit (GLCS) that induces loading on the body to mimic standing and - when integrated with other countermeasures - exercising on Earth. Comfort, mobility and other operational issues were explored during a pilot study carried out in parabolic flight for prototype suits worn by three subjects. Compared to the 1- or 2-stage Russian Pingvin Suits, the elastic mesh of the GLCS can create a loading regime that gradually increases in hundreds of stages from the shoulders to the feet, thereby reproducing the weight-bearing regime normally imparted by gravity with much higher resolution. Modelling shows that the skinsuit requires less than 10 mmHg (1.3 kPa) of compression for three subjects of varied gender, height and mass. Negligible mobility restriction and excellent comfort properties were found during the parabolic flights, which suggests that crewmembers should be able to work normally, exercise or sleep while wearing the suit. The suit may also serve as a practical 1 g harness for exercise countermeasures and vibration applications to improve dynamic loading.

Operation regimes of a dielectric laser accelerator

Science.gov (United States)

Hanuka, Adi; Schächter, Levi

2018-04-01

We investigate three operation regimes in dielectric laser driven accelerators: maximum efficiency, maximum charge, and maximum loaded gradient. We demonstrate, using a self-consistent approach, that loaded gradients of the order of 1 to 6 [GV/m], efficiencies of 20% to 80%, and electrons flux of 1014 [el/s] are feasible, without significant concerns regarding damage threshold fluence. The latter imposes that the total charge per squared wavelength is constant (a total of 106 per μm2). We conceive this configuration as a zero-order design that should be considered for the road map of future accelerators.

Multi-fluid modeling of low-recycling divertor regimes

International Nuclear Information System (INIS)

Smirnov, R.D.; Pigarov, A.Yu.; Krasheninnikov, S.I.; Rognlien, T.D.; Soukhanovskii, V.A.; Rensink, M.E.; Maingi, R.; Skinner, C.H.; Stotler, D.P.; Bell, R.E.; Kugel, H.W.

2010-01-01

The low-recycling regimes of divertor operation in a single-null NSTX magnetic configuration are studied using computer simulations with the edge plasma transport code UEDGE. The edge plasma transport properties pertinent to the low-recycling regimes are demonstrated. These include the flux-limited character of the parallel heat transport and the high plasma temperatures with the flattened profiles in the scrape-off-layer. It is shown that to maintain the balance of particle fluxes at the core interface the deuterium gas puffing rate should increase as the divertor recycling coefficient decreases. The radial profiles of the heat load to the outer divertor plate, the upstream radial plasma profiles, and the effects of the cross-field plasma transport in the low-recycling regimes are discussed. It is also shown that recycling of lithium impurities evaporating from the divertor plate at high surface temperatures can reverse the low-recycling divertor operational regime to the high-recycling one and may cause thermal instability of the divertor plate (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Generation and development of damage in double forged tungsten in different combined regimes of irradiation with extreme heat loads

Science.gov (United States)

Paju, Jana; Väli, Berit; Laas, Tõnu; Shirokova, Veroonika; Laas, Katrin; Paduch, Marian; Gribkov, Vladimir A.; Demina, Elena V.; Prusakova, Marina D.; Pimenov, Valeri N.; Makhlaj, Vadym A.; Antonov, Maksim

2017-11-01

Armour materials in fusion devices, especially in the region of divertor, are exposed to a continuous heat and particle load. In addition, several off-normal events can reach the material during a work session. Calculations show that the effects of plasma and heat during such events can lead to cracking, erosion and detachment of the armour material. On the other hand, mutual and combined influences of different kinds of heat and particle loads can lead to the amplification of defects or vice versa, to the mitigation of damages. Therefore, the purpose of the study is to investigate the plasma induced damages on samples of double forged tungsten, which is considered a potential candidate for armour material of future tokamak's divertor. The combined effect of different kinds of plasma induced damages was investigated and analysed in this research. The study was conducted by irradiating the samples in various irradiation regimes twice, to observe the accumulation of the damages. Afterwards the analysis of micro-topography, scanning electron microscopy images and electrical conductivity measurements was used. Results indicate that double-forging improved the tungsten's durability to irradiation. Nevertheless, powerful pulses lead to significant damage of the sample, which will lead to further deterioration in the bulk. Although the average micro-roughness on the sample's surface does not change, the overall height/depth ratios can change.

Unified flow regime predictions at earth gravity and microgravity

International Nuclear Information System (INIS)

Crowley, C.J.

1990-01-01

This paper illustrates the mechanistic models developed to predict flow regime transitions at earth gravity for various pipe inclinations can be successfully applied to existing microgravity flow regime data from several experiments. There is a tendency in the literature for flow regime comparisons in several inclination ranges and at various gravity (acceleration) levels to be treated by separate models, resulting in a proliferation of models for the prediction of flow regimes. One set of mechanistic models can be used to model the transitions between stratified, slug, bubbly, and annular flow regimes in pipes for all acceleration vectors and magnitudes from earth gravity to microgravity

Two lighter than air systems in opposing flight regimes: An unmanned short haul, heavy load transport balloon and a manned, light payload airship

Science.gov (United States)

Pohl, R. A.

1975-01-01

Lighter Than Air vehicles are generally defined or categorized by the shape of the balloon, payload capacity and operational flight regime. Two balloon systems that are classed as being in opposite categories are described. One is a cable guided, helium filled, short haul, heavy load transport Lighter Than Air system with a natural shaped envelope. The other is a manned, aerodynamic shaped airship which utilizes hot air as the buoyancy medium and is in the light payload class. While the airship is in the design/fabrication phase with flight tests scheduled for the latter part of 1974, the transport balloon system has been operational for some eight years.

Computation of shakedown loads feasibility study

International Nuclear Information System (INIS)

Save, M.; Saxce, G. de; Borkowski, A.

1991-01-01

Structures submitted to variable loads and temperature fields may enter in a regime of ratcheting where strains and hence structural deflections increase cycle by cycle. It is important to demonstrate that ratcheting is avoided. This happens of course if the structure remains entirely in the elastic regime. However, for more severe loadings, plastic deformations occur and the analyst must then demonstrate that the structure shakes down or adapts. Shakedown may be elastic if after a transient period all strain variations become elastic, or plastic when alternating plasticity occurs. This report addresses plastic shakedown. The problem is treated from the theoretical point of view but also - and this is a very important part of the work - from the numerical and software point of view

Transient dynamics of a quantum-dot: From Kondo regime to mixed valence and to empty orbital regimes

Science.gov (United States)

Cheng, YongXi; Li, ZhenHua; Wei, JianHua; Nie, YiHang; Yan, YiJing

2018-04-01

Based on the hierarchical equations of motion approach, we study the time-dependent transport properties of a strongly correlated quantum dot system in the Kondo regime (KR), mixed valence regime (MVR), and empty orbital regime (EOR). We find that the transient current in KR shows the strongest nonlinear response and the most distinct oscillation behaviors. Both behaviors become weaker in MVR and diminish in EOR. To understand the physical insight, we examine also the corresponding dot occupancies and the spectral functions, with their dependence on the Coulomb interaction, temperature, and applied step bias voltage. The above nonlinear and oscillation behaviors could be understood as the interplay between dynamical Kondo resonance and single electron resonant-tunneling.

Vibration analysis of a hydro generator for different operating regimes

Science.gov (United States)

Haţiegan, C.; Pădureanu, I.; Jurcu, M.; Nedeloni, M. D.; Hamat, C. O.; Chioncel, C. P.; Trocaru, S.; Vasile, O.; Bădescu, O.; Micliuc, D.; (Filip Nedeloni, L.; Băra, A.; (Barboni Haţiegan, L.

2017-01-01

Based on experimental measurements, this paper presents the vibration analysis of a hydro generator that equips a Kaplan hydraulic turbine of a Hydropower plant in Romania. This analysis means vibrations measurement to different operating regimes of the hydro generator respectively before installing it and into operation, namely putting off load mode (unexcited and excited) respectively putting on load mode. By comparing, through the experimental results obtained before and after the operation of hydro aggregates are observed vibrations improvements.

Effect of Stagger on the Vibroacoustic Loads from Clustered Rockets

Science.gov (United States)

Rojo, Raymundo; Tinney, Charles E.; Ruf, Joseph H.

2016-01-01

The effect of stagger startup on the vibro-acoustic loads that form during the end- effects-regime of clustered rockets is studied using both full-scale (hot-gas) and laboratory scale (cold gas) data. Both configurations comprise three nozzles with thrust optimized parabolic contours that undergo free shock separated flow and restricted shock separated flow as well as an end-effects regime prior to flowing full. Acoustic pressure waveforms recorded at the base of the nozzle clusters are analyzed using various statistical metrics as well as time-frequency analysis. The findings reveal a significant reduction in end- effects-regime loads when engine ignition is staggered. However, regardless of stagger, both the skewness and kurtosis of the acoustic pressure time derivative elevate to the same levels during the end-effects-regime event thereby demonstrating the intermittence and impulsiveness of the acoustic waveforms that form during engine startup.

Regime switching model for financial data: Empirical risk analysis

Science.gov (United States)

Salhi, Khaled; Deaconu, Madalina; Lejay, Antoine; Champagnat, Nicolas; Navet, Nicolas

2016-11-01

This paper constructs a regime switching model for the univariate Value-at-Risk estimation. Extreme value theory (EVT) and hidden Markov models (HMM) are combined to estimate a hybrid model that takes volatility clustering into account. In the first stage, HMM is used to classify data in crisis and steady periods, while in the second stage, EVT is applied to the previously classified data to rub out the delay between regime switching and their detection. This new model is applied to prices of numerous stocks exchanged on NYSE Euronext Paris over the period 2001-2011. We focus on daily returns for which calibration has to be done on a small dataset. The relative performance of the regime switching model is benchmarked against other well-known modeling techniques, such as stable, power laws and GARCH models. The empirical results show that the regime switching model increases predictive performance of financial forecasting according to the number of violations and tail-loss tests. This suggests that the regime switching model is a robust forecasting variant of power laws model while remaining practical to implement the VaR measurement.

Applying of the array transducers' technology for surface acoustic waves materials characterization in the transient regime

International Nuclear Information System (INIS)

Frenet, D.

2000-01-01

In this document we present a theoretical and experimental study which has been led to design a surface acoustic wave device for local characterisation (relatively to the wavelength) of isotropic or anisotropic materials. The device is based on a phased-array transducer of conical shape we have specifically designed for this purpose. It operates in the impulsive mode, in the frequency range of 1-5 MHz. In order to deduce mechanical properties of the material, it is possible to measure the surface wave characteristics (velocity, attenuation,...). Different methods for measuring the wave velocity have been developed taking advantage of from the phased-array technology. The originality of theses methods relies on the fact that the measures are performed without moving the transducer. Consequently, the device requires no additional mechanical system and it is quite compact. In addition, this shortens the characterisation process duration comparatively to the usually available methods (e. g. the V(z) technique). In the theoretical section of this study, a versatile model allowing to simulate in the time harmonic regime as well as in the transient regime, the transmitted field, the field reflected on isotropic or anisotropic planar samples and the output voltage for transducers of arbitrary shapes has been developed. The model has been applied to the phased-array conical transducer as well as to more classical transducers such as planar (rectangular) or focusing (spherically or cylindrically shaped) transducers. It predicts not only the geometrical contributions of the reflected field and signal but also the leaky contributions related to the surface acoustic waves. (author)

Compliance variations in the fatigue thresold regime of a low alloy ferritic steel under closure-free testing conditions

International Nuclear Information System (INIS)

Vaidya, W.V.

1991-01-01

Compliance variations in the threshold regime of a high strength ferritic steel tested under closure-free conditions at room temperature and in air are reported. In contrast to the Paris regime, and irrespective of whether the data during load shedding, at threshold or after postthreshold load increase are considered, it is found that comparatively compliance varies inconsistently in the threshold regime. Therefore, a 1:1 correlation between the averaged optical crack length and that inferred from compliance was not observed. This discrepancy is analyzed. The variations in compliance are utilized to infer the crack front behavior, and the results are discussed in terms of the microstructural impedance. (orig.) With 22 figs., 2 appendices [de

Crack growth prediction for low-cycle fatigue regime

International Nuclear Information System (INIS)

Kamaya, Masayuki

2017-01-01

The objective of this study is to show a crack growth prediction procedure for the low-cycle fatigue regime. First, fatigue crack growth tests using Type 316 stainless steel specimens at room temperature were reviewed. It was seen that the crack growth rates correlated well with the equivalent stress intensify factor, which was derived using strain range instead of stress range. Furthermore, the effective equivalent stress intensify factor derived using the effective strain range exhibited excellent correlation with the crack growth rates obtained under various specimen geometries and loading conditions including high and low-cycle regimens. The obtained crack growth rates were also compared with the growth rate prescribed in the fitness-for-service code of the Japan Society of Mechanical Engineers (JSME). The test results agreed with the growth rate of JSME code. Finally, the procedure for predicting the low-cycle fatigue crack growth was shown. Although the JSME code is aimed at predicting fatigue crack growth for the so-called small scale yielding condition (high-cycle fatigue regime), the material constants determined for the high-cycle fatigue regime can be used even for the low-cycle fatigue regime. (author)

Dynamic Effect of a Change in the Exchange Rate System: From a Fixed Regime to a Basket-Peg or a Floating Regime

OpenAIRE

Yoshino, Naoyuki; Kaji, Sahoko; Asonuma, Tamon

2015-01-01

This paper theoretically evaluates the dynamic effects of a shift in an exchange rate system from a fixed regime to a basket peg, or to a floating regime, and obtains transition paths for the shift based on a dynamic stochastic general equilibrium model of a small open economy. We apply quantitative analysis using data from the People's Republic of China and Thailand and find that a small open country would be better off shifting to a basket peg or to a floating regime than maintaining a doll...

Coulomb drag in the mesoscopic regime

DEFF Research Database (Denmark)

Mortensen, N. Asger; Flensberg, Karsten; Jauho, Antti-Pekka

2002-01-01

We present a theory for Coulomb drug between two mesoscopic systems which expresses the drag in terms of scattering matrices and wave functions. The formalism can be applied to both ballistic and disordered systems and the consequences can be studied either by numerical simulations or analytic...... means such as perturbation theory or random matrix theory. The physics of Coulomb drag in the mesoscopic regime is very different from Coulomb drag between extended electron systems. In the mesoscopic regime we in general find fluctuations of the drag comparable to the mean value. Examples are vanishing...

Coulomb drag in the mesoscopic regime

DEFF Research Database (Denmark)

Mortensen, N.A.; Flensberg, Karsten; Jauho, Antti-Pekka

2002-01-01

We present a theory for Coulomb drag between two mesoscopic systems which expresses the drag in terms of scattering matrices and wave functions. The formalism can be applied to both ballistic and disordered systems and the consequences can be studied either by numerical simulations or analytic...... means such as perturbation theory or random matrix theory. The physics of Coulomb drag in the mesoscopic regime is very different from Coulomb drag between extended electron systems. In the mesoscopic regime we in general find fluctuations of the drag comparable to the mean value. Examples are vanishing...

THE EFFECTS OF DIFFERENT WORK-LOADING APPLIED TO THE WORKERS THAT WORK PRODUCING OF SHIRT TO THE SEAM FAULT RATES

Directory of Open Access Journals (Sweden)

Önder YÜCEL

2001-03-01

Full Text Available Human efficiency is of big importance in the clothing industry. So as to provide high quality and productivity stabilized work –loading must be given to the workers that work in the cloth production lines. In addition to it, the kind of work must be paid attention in the studies to be done on stabilized work-loading. The aim of this study is to determine the effects of different work-loading to the seam fault rates. For this purpose, four different work-loading had been applied to the workers and determined seam faults on the clothes had been recorded. As a result of this study, seam fault rates in the different work-loading had been evaluated.

Asset allocation and regime switching on Croatian financial market

Directory of Open Access Journals (Sweden)

Tihana Škrinjarić

2016-12-01

Full Text Available It has been known for quite some time now that financial markets exhibit changes in regimes over time. A majority of the literature tends to support that financial markets undergo regimes of bull and bear markets. This characteristic should be modeled in a proper way as investors are always interested in beating the market: either by achieving better returns than others, or by minimizing their portfolio risks. There exist many mathematical and statistical models that are used as tools to achieve the mentioned goals. Introducing the regime switching methodology in existing models has proven to be facilitate achieving such goals. Therefore, the objective of this study is to utilize the regime switching methodology on the Croatian financial market to ascertain its usefulness for Croatian investors. Multivariate regime switching and non-switching models were estimated using daily data from the period 2 January 2007 to 31 December 2015. The assumption is that the investor is interested in stock and bond markets. The results from the MGARCH and regime switching MGARCH models are then compared in order to give answers as to whether the respective methodology applied to the Croatian market is useful and how it may benefit investors. Most of the results support the presumption of incorporating this particular methodology in financial modeling for the Croatia markets. This is the first research that applies the regime switching MGARCH methodology in Croatia (including the Balkan region, hence we expect that this will be a significant contribution to existing methodologies in literature.

Technological regimes and sources of entrepreneurship

NARCIS (Netherlands)

Marsili, O.

2000-01-01

This paper concerns the technological detenninants of entrepreneurial behaviour. By applying a typology of technological regimes, which describes the nature of the technological environment in which finns operate, this paper examines the sources and obstacle to entrepreneurial entry related to the

Technological regimes and sources of entrepreneurship

NARCIS (Netherlands)

Marsili, O.

2002-01-01

This paper concerns the technological determinants of entrepreneurial behaviour. By applying a typology of technological regimes, which describes the nature of the technological environment in which firms operate, this paper examines the sources and obstacles to entrepreneurial entry related to the

Experience in verification regimes. United States On-Site Inspection Agency

International Nuclear Information System (INIS)

Reppert, J.

1998-01-01

Experiences are described of the United States On-site Inspection Agency in verification regimes all over the world where it has been applied in the last 30 years. The challenge for the future is to extend the benefits of the applied tools to all states in all regions to enhance stability and to create conditions for peace at lower levels of armaments than currently exist. The USA need to engage states currently caught in cycles of violence and arms escalation. They must examine technologies which together with on-site aspects of verification or transparency regimes can provide a comprehensive picture at affordable costs. They foresee a growth in combined training with new states entering for the first time into regime that include arms control and transparency measure

A study on the optimal hydraulic loading rate and plant ratios in recirculation aquaponic system.

Science.gov (United States)

Endut, Azizah; Jusoh, A; Ali, N; Wan Nik, W B; Hassan, A

2010-03-01

The growths of the African catfish (Clarias gariepinus) and water spinach (Ipomoea aquatica) were evaluated in recirculation aquaponic system (RAS). Fish production performance, plant growth and nutrient removal were measured and their dependence on hydraulic loading rate (HLR) was assessed. Fish production did not differ significantly between hydraulic loading rates. In contrast to the fish production, the water spinach yield was significantly higher in the lower hydraulic loading rate. Fish production, plant growth and percentage nutrient removal were highest at hydraulic loading rate of 1.28 m/day. The ratio of fish to plant production has been calculated to balance nutrient generation from fish with nutrient removal by plants and the optimum ratio was 15-42 gram of fish feed/m(2) of plant growing area. Each unit in RAS was evaluated in terms of oxygen demand. Using specified feeding regime, mass balance equations were applied to quantify the waste discharges from rearing tanks and treatment units. The waste discharged was found to be strongly dependent on hydraulic loading rate. 2009 Elsevier Ltd. All rights reserved.

Immune networks: multi-tasking capabilities at medium load

International Nuclear Information System (INIS)

Agliari, E; Annibale, A; Barra, A; Coolen, A C C; Tantari, D

2013-01-01

Associative network models featuring multi-tasking properties have been introduced recently and studied in the low-load regime, where the number P of simultaneously retrievable patterns scales with the number N of nodes as P ∼ log N. In addition to their relevance in artificial intelligence, these models are increasingly important in immunology, where stored patterns represent strategies to fight pathogens and nodes represent lymphocyte clones. They allow us to understand the crucial ability of the immune system to respond simultaneously to multiple distinct antigen invasions. Here we develop further the statistical mechanical analysis of such systems, by studying the medium-load regime, P ∼ N δ with δ ∈ (0, 1]. We derive three main results. First, we reveal the nontrivial architecture of these networks: they exhibit a high degree of modularity and clustering, which is linked to their retrieval abilities. Second, by solving the model we demonstrate for δ < 1 the existence of large regions in the phase diagram where the network can retrieve all stored patterns simultaneously. Finally, in the high-load regime δ = 1 we find that the system behaves as a spin-glass, suggesting that finite-connectivity frameworks are required to achieve effective retrieval. (paper)

Comparing in-service multi-input loads applied on non-stiff components submitted to vibration fatigue to provide specifications for robust design

Directory of Open Access Journals (Sweden)

Le Corre Gwenaëlle

2018-01-01

Full Text Available This study focuses on applications from the automotive industry, on mechanical components submitted to vibration loads. On one hand, the characterization of loading for dimensioning new structures in fatigue is enriched and updated by customer data analysis. On the other hand, the loads characterization also aims to provide robust specifications for simulation or physical tests. These specifications are needed early in the project, in order to perform the first durability verification activities. At this time, detailed information about the geometry and the material is rare. Vibration specifications need to be adapted to a calculation time or physical test durations in accordance with the pace imposed by the projects timeframe. In the trucks industry, the dynamic behaviour can vary significantly from one configuration of truck to another, as the trucks architecture impacts the load environment of the components. The vibration specifications need to be robust by taking care of the diversity of vehicles and markets considered in the scope of the projects. For non-stiff structures, the lifetime depends, among other things, on the frequency content of the loads, as well as the interactions between the components of the multi-input loads. In this context, this paper proposes an approach to compare sets of variable amplitude multi-input loads applied on non-stiff structures. The comparison is done in terms of damage, with limited information on the structure where the loads sets are applied on. The methodology is presented, as well as an application. Activities planned to validate the methodology are also exposed.

Surface pressure and aerodynamic loads determination of a transonic airfoil based on particle image velocimetry

International Nuclear Information System (INIS)

Ragni, D; Ashok, A; Van Oudheusden, B W; Scarano, F

2009-01-01

The present investigation assesses a procedure to extract the aerodynamic loads and pressure distribution on an airfoil in the transonic flow regime from particle image velocimetry (PIV) measurements. The wind tunnel model is a two-dimensional NACA-0012 airfoil, and the PIV velocity data are used to evaluate pressure fields, whereas lift and drag coefficients are inferred from the evaluation of momentum contour and wake integrals. The PIV-based results are compared to those derived from conventional loads determination procedures involving surface pressure transducers and a wake rake. The method applied in this investigation is an extension to the compressible flow regime of that considered by van Oudheusden et al (2006 Non-intrusive load characterization of an airfoil using PIV Exp. Fluids 40 988–92) at low speed conditions. The application of a high-speed imaging system allows the acquisition in relatively short time of a sufficient ensemble size to compute converged velocity statistics, further translated in turbulent fluctuations included in the pressure and loads calculation, notwithstanding their verified negligible influence in the computation. Measurements are performed at varying spatial resolution to optimize the loads determination in the wake region and around the airfoil, further allowing us to assess the influence of spatial resolution in the proposed procedure. Specific interest is given to the comparisons between the PIV-based method and the conventional procedures for determining the pressure coefficient on the surface, the drag and lift coefficients at different angles of attack. Results are presented for the experiments at a free-stream Mach number M = 0.6, with the angle of attack ranging from 0° to 8°

Plastic limit loads for cylindrical shell intersections under combined loading

International Nuclear Information System (INIS)

Skopinsky, V.N.; Berkov, N.A.; Vogov, R.A.

2015-01-01

In this research, applied methods of nonlinear analysis and results of determining the plastic limit loads for shell intersection configurations under combined internal pressure, in-plane moment and out-plane moment loadings are presented. The numerical analysis of shell intersections is performed using the finite element method, geometrically nonlinear shell theory in quadratic approximation and plasticity theory. For determining the load parameter of proportional combined loading, the developed maximum criterion of rate of change of relative plastic work is employed. The graphical results for model of cylindrical shell intersection under different two-parameter combined loadings (as generalized plastic limit load curves) and three-parameter combined loading (as generalized plastic limit load surface) are presented on the assumption that the internal pressure, in-plane moment and out-plane moment loads were applied in a proportional manner. - Highlights: • This paper presents nonlinear two-dimensional FE analysis for shell intersections. • Determining the plastic limit loads under combined loading is considered. • Developed maximum criterion of rate of change of relative plastic work is employed. • Plastic deformation mechanism in shell intersections is discussed. • Results for generalized plastic limit load curves of branch intersection are presented

Modification of Hertzian behaviour in heavily loaded contact in the DMT regime

International Nuclear Information System (INIS)

Wu, J-J

2008-01-01

The adhesive contact between spheres for a small Tabor parameter is investigated. It is found that the DMT model cannot describe the adhesive contact for a small Tabor parameter. By assuming a new contact distance, the modified Hertzian contact is proposed. For a small Tabor parameter, the rigid-sphere model can describe the adhesive contact behaviour for a small load and the modified Hertzian model can describe the adhesive contact behaviour for a large load

Conceptual proposals for measuring the impact of international regimes on energy security

International Nuclear Information System (INIS)

Sander, Michael

2013-01-01

The paper proposes two concepts to assess the effect of international regimes on energy security. Existing indicators focus mainly on state-level factors, excluding international influences. International relation scholars on the other hand see a clear connection between international regimes and stable energy relations. International regimes stabilise energy relations by providing frameworks for negotiations, defining, controlling and sanctioning compliance and allowing the actors to engage in package deals. The researcher needs to include these factors in a complete assessment of political energy security risks. As first step, the paper uses the effectiveness of control mechanisms as basis for such consideration. It refers specifically to international arbitration as the most important control mechanism in international energy relations. The simplest measurement option is the share of a county's energy imports covered by a certain regime. The paper applies the Oslo-Potsdam-Solution to account for outcome effectiveness. It applies a variant of the International Regimes Data Base protocol to account for effective regime structures. In a last section, the paper proposes some possible paths for future research. - Highlights: • International regimes mitigate political risks for energy supply and must be considered. • The paper proposes two concepts to measure energy regime effectiveness. • The OPS-variant measures output, the IRDB-variant measures structure effectiveness. • The paper offers a preliminary feasibility test for the concepts. • Finally, it suggests further roads for research

Facilitated movement of inertial Brownian motors driven by a load under an asymmetric potential.

Science.gov (United States)

Ai, Bao-quan; Liu, Liang-gang

2007-10-01

Based on recent work [L. Machura, M. Kostur, P. Talkner, J. Luczka, and P. Hanggi, Phys. Rev. Lett. 98, 040601 (2007)], we extend the study of inertial Brownian motors to the case of an asymmetric potential. It is found that some transport phenomena appear in the presence of an asymmetric potential. Within tailored parameter regimes, there exists two optimal values of the load at which the mean velocity takes its maximum, which means that a load can facilitate the transport in the two parameter regimes. In addition, the phenomenon of multiple current reversals can be observed when the load is increased.

Regime-Switching Risk: To Price or Not to Price?

Directory of Open Access Journals (Sweden)

Tak Kuen Siu

2011-01-01

“normative” issues to be addressed in pricing contingent claims under a Markovian, regime-switching, Black-Scholes-Merton model. We address this issue using a minimal relative entropy approach. Firstly, we apply a martingale representation for a double martingale to characterize the canonical space of equivalent martingale measures which may be viewed as the largest space of equivalent martingale measures to incorporate both the diffusion risk and the regime-switching risk. Then we show that an optimal equivalent martingale measure over the canonical space selected by minimizing the relative entropy between an equivalent martingale measure and the real-world probability measure does not price the regime-switching risk. The optimal measure also justifies the use of the Esscher transform for option valuation in the regime-switching market.

The theory of critical distances applied to problems in fracture and fatigue of bone

Directory of Open Access Journals (Sweden)

Emma Brazel

2009-10-01

Full Text Available The theory of critical distances (TCD has been applied to predict notch-based fracture and fatigue in a wide range of materials and components. The present paper describes a series of projects in which we applied this approach to human bone. Using experimental data from the literature, combined with finite element analysis, we showed that the TCD was able to predict the effect of notches and holes on the strength of bone failing in brittle fracture due to monotonic loading, in different loading regimes. Bone also displays short crack effects, leading to R-curve data for both fracture toughness and fatigue crack propagation thresholds; we showed that the TCD could predict this data. This analysis raised a number of questions for discussion, such as the significance of the L value itself in this and other materials. Finally, we applied the TCD to a practical problem in orthopaedic surgery: the management of bone defects, showing that predictions could be made which would enable surgeons to decide on whether a bone graft material would be needed to repair a defect, and to specify what mechanical properties this material should have.

Load theory behind the wheel; perceptual and cognitive load effects.

Science.gov (United States)

Murphy, Gillian; Greene, Ciara M

2017-09-01

Perceptual Load Theory has been proposed as a resolution to the longstanding early versus late selection debate in cognitive psychology. There is much evidence in support of Load Theory but very few applied studies, despite the potential for the model to shed light on everyday attention and distraction. Using a driving simulator, the effect of perceptual and cognitive load on drivers' visual search was assessed. The findings were largely in line with Load Theory, with reduced distractor processing under high perceptual load, but increased distractor processing under high cognitive load. The effect of load on driving behaviour was also analysed, with significant differences in driving behaviour under perceptual and cognitive load. In addition, the effect of perceptual load on drivers' levels of awareness was investigated. High perceptual load significantly increased inattentional blindness and deafness, for stimuli that were both relevant and irrelevant to driving. High perceptual load also increased RTs to hazards. The current study helps to advance Load Theory by illustrating its usefulness outside of traditional paradigms. There are also applied implications for driver safety and roadway design, as the current study suggests that perceptual and cognitive load are important factors in driver attention. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

QCD in the {delta}-regime

Energy Technology Data Exchange (ETDEWEB)

Bietenholz, W. [Universidad Nacional Autonoma de Mexico, Mexico City (Mexico). Inst. de Ciencias Nucleares; Cundy, N. [Seoul National Univ. (Korea, Republic of). Lattice Gauge Theory Research Center; Goeckeler, M. [Regensburg Univ. (Germany). Inst. fuer Theoretische Physik; Horsley, R.; Zanotti, J.M. [Edinburgh Univ. (United Kingdom). School of Physics; Nakamura, Y. [Tsukuba Univ., Ibaraki (Japan). Center for Computational Sciences; Pleiter, D. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Rakow, P.E.L. [Liverpool Univ. (United Kingdom). Theoretical Physics Div.; Schierholz, G. [Regensburg Univ. (Germany). Inst. fuer Theoretische Physik; Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

2011-03-15

The {delta}-regime of QCD is characterised by light quarks in a small spatial box, but a large extent in (Euclidean) time. In this setting a specific variant of chiral perturbation theory - the {delta}-expansion - applies, based on a quantum mechanical treatment of the quasi onedimensional system. In particular, for vanishing quark masses one obtains a residual pion mass M{sup R}{sub {pi}}, which has been computed to the third order in the {delta}-expansion. A comparison with numerical measurements of this residual mass allows for a new determination of some Low Energy Constants, which appear in the chiral Lagrangian. We first review the attempts to simulate 2-flavour QCD directly in the {delta}-regime. This is very tedious, but results compatible with the predictions for M{sup R}{sub {pi}} have been obtained. Then we show that an extrapolation of pion masses measured in a larger volume towards the {delta}-regime leads to good agreement with the theoretical predictions. From those results, we also extract a value for the (controversial) sub-leading Low Energy Constant anti l{sub 3}. (orig.)

QCD in the δ-regime

International Nuclear Information System (INIS)

Bietenholz, W.; Rakow, P.E.L.

2011-03-01

The δ-regime of QCD is characterised by light quarks in a small spatial box, but a large extent in (Euclidean) time. In this setting a specific variant of chiral perturbation theory - the δ-expansion - applies, based on a quantum mechanical treatment of the quasi onedimensional system. In particular, for vanishing quark masses one obtains a residual pion mass M R π , which has been computed to the third order in the δ-expansion. A comparison with numerical measurements of this residual mass allows for a new determination of some Low Energy Constants, which appear in the chiral Lagrangian. We first review the attempts to simulate 2-flavour QCD directly in the δ-regime. This is very tedious, but results compatible with the predictions for M R π have been obtained. Then we show that an extrapolation of pion masses measured in a larger volume towards the δ-regime leads to good agreement with the theoretical predictions. From those results, we also extract a value for the (controversial) sub-leading Low Energy Constant anti l 3 . (orig.)

Can we "apply" the findings of Forster and Lavie (2008)? On the generalizability of attentional capture effects under varying levels of perceptual load.

Science.gov (United States)

Lleras, Alejandro; Chu, Hengqing; Buetti, Simona

2017-06-01

Perceptual Load theory states that the degree of perceptual load on a display determines the amount of leftover attentional resources that the system can use to process distracting information. An important corollary of this theory is that the amount of perceptual load determines the vulnerability of the attention system to being captured by completely irrelevant stimuli, predicting larger amounts of capture with low perceptual load than with high perceptual load. This prediction was first confirmed by Forster and Lavie (2008). Here, we report 6 experiments that followed up on those earlier results, where we find that in many cases, the opposite pattern is obtained: attentional capture increased with increasing perceptual load. Given the lack of generalizability of the theory to new experimental contexts with fairly minor methodological differences, we conclude that Perceptual Load may not be a useful framework for understanding attentional capture. The theoretical and applied importance of these findings is discussed. In particular, we caution against using this theory in applied tasks and settings because best-use recommendations stemming from this theory regarding strategies to decrease distractibility may in fact produce the opposite effect: an increase in distractibility (with distractibility being indexed by the magnitude of the capture effect). (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Lattice strain evolution in IMI 834 under applied stress

International Nuclear Information System (INIS)

Daymond, Mark R.; Bonner, Neil W.

2003-01-01

The effect of elastic and plastic anisotropy on the evolution of lattice strains in the titanium alloy IMI834 has been examined during a uniaxial tensile test, by in situ monitoring on the Engin instrument at the ISIS pulsed neutron source. Measurements were made at load during an incremental loading test. The data is analysed in the light of the requirements for engineering residual stress scanning measurements performed at polychromatic neutron and synchrotron diffraction sources. Comparisons between the measured strains from different lattice families and the predictions from an elasto-plastic self-consistent model are made. Agreement is good in the elastic regime and for most diffraction planes in the plastic regime

Yukon's common oil and gas regime

International Nuclear Information System (INIS)

Love, B.

1998-01-01

The Yukon's common oil and gas regime was developed in partnership with First Nations and it sets out the rules that will apply throughout the Yukon and on Yukon and First Nation lands. While separate and distinct, it conforms with and is compatible with other government systems and regimes. The major elements of the common regime include the Oil and Gas Act, regulations, policies, processes and agreements. The specific opportunities that are available in each phase of oil and gas development in the Yukon are described, with a map showing all basins, reserves and sites of current oil and gas activity. The Yukon has eight potential oil and gas basins: North Coast, Old Crow, Kandik, Eagle Plain, Peel Plateau, Bonnet Plume, Whitehorse Trough, and Liard Plateau. Only three of the eight, the Liard Plateau, Whitehorse Trough and Eagle Plain, have been explored. No wells have been drilled in several of Yukon's basins. Factors influencing economic opportunities in the Territory are also described, including: (1) international events and energy markets, (2) North American gas markets, (3) environmental factors, (4) competitiveness of the Yukon regime, and (5) the commitment of industry resources. 4 figs

The application of neural networks to flow regime identification

International Nuclear Information System (INIS)

Embrechts, M.; Yapo, T.C.; Lahey, R.T. Jr.

1993-01-01

This paper deals with the application of a Kohonen map for the identification of two-phase flow regimes where a mixture of gas and fluid flows through a horizontal tube. Depending on the relative flow velocities of the gas and the liquid phase, four distinct flow regimes can be identified: Wavy flow, plug flow, slug flow and annular flow. A schematic of these flow regimes is presented. The objective identification of two-phase flow regimes constitutes an important and challenging problem for the design of safe and reliable nuclear power plants. Previous attempts to classify these flow regimes are reviewed by Franca and Lahey. The authors describe how a Kohonen map can be applied to distinguish between flow regimes based on the Fourier power spectra and wavelet transforms of pressure drop fluctuations. The Fourier power spectra allowed the Kohonen map to identify the flow regimes successfully. In contrast, the Kohonen maps based on a wavelet transform could only distinguish between wavy and annular flows. An analysis of typical two-phase pressure drop data for an air/water mixture in a horizontal pipe is presented. Use of the wavelet transform and the Kohonen feature map are discussed

Time-lapse nanoscopy of friction in the non-Amontons and non-Coulomb regime.

Science.gov (United States)

Ishida, Tadashi; Sato, Takaaki; Ishikawa, Takahiro; Oguma, Masatsugu; Itamura, Noriaki; Goda, Keisuke; Sasaki, Naruo; Fujita, Hiroyuki

2015-03-11

Originally discovered by Leonard da Vinci in the 15th century, the force of friction is directly proportional to the applied load (known as Amontons' first law of friction). Furthermore, kinetic friction is independent of the sliding speed (known as Coulomb's law of friction). These empirical laws break down at high normal pressure (due to plastic deformation) and low sliding speed (in the transition regime between static friction and kinetic friction). An important example of this phenomenon is friction between the asperities of tectonic plates on the Earth. Despite its significance, little is known about the detailed mechanism of friction in this regime due to the lack of experimental methods. Here we demonstrate in situ time-lapse nanoscopy of friction between asperities sliding at ultralow speed (∼0.01 nm/s) under high normal pressure (∼GPa). This is made possible by compressing and rubbing a pair of nanometer-scale crystalline silicon anvils with electrostatic microactuators and monitoring its dynamical evolution with a transmission electron microscope. Our analysis of the time-lapse movie indicates that superplastic behavior is induced by decrystallization, plastic deformation, and atomic diffusion at the asperity-asperity interface. The results hold great promise for a better understanding of quasi-static friction under high pressure for geoscience, materials science, and nanotechnology.

Typification of the thermal regime of the air in Nicaragua

International Nuclear Information System (INIS)

Lecha Estela, Luis; Hernandez Perez, Vidal; Prado Zambrana, Carmen

1994-01-01

In this work it is applied the method of thermal regime classification in order to evaluate the heat resources of the country, as a first step to know and to employ, rationally, the national climatic resources. It is analyzed the interaction between the spatio-temporal distribution of the thermal regime and the main climatic factors, showing the differences encountered between each geographic zone of the country and, moreover, they vertical structure. The results have applied utility in several branches of the national economy and they were included in the work to prepare the Climatic Atlas of Nicaragua

Using neutral models to identify constraints on low-severity fire regimes.

Science.gov (United States)

Donald McKenzie; Amy E. Hessl; Lara-Karena B. Kellogg

2006-01-01

Climate, topography, fuel loadings, and human activities all affect spatial and temporal patterns of fire occurrence. Because fire is modeled as a stochastic process, for which each fire history is only one realization, a simulation approach is necessary to understand baseline variability, thereby identifying constraints, or forcing functions, that affect fire regimes...

European energy security analysing the EU-Russia energy security regime in terms of interdependence theory

CERN Document Server

Esakova, Nataliya

2012-01-01

Nataliya Esakova performs an analysis of the interdependencies and the nature of cooperation between energy producing, consuming and transit countries focusing on the gas sector. For the analysis the theoretical framework of the interdependence theory by Robert O. Keohane and Joseph S. Nye and the international regime theory are applied to the recent developments within the gas relationship between the European Union and Russia in the last decade. The objective of the analysis is to determine, whether a fundamental regime change in terms of international regime theory is taking place, and, if so, which regime change explanation model in terms of interdependence theory is likely to apply.

European energy security. Analysing the EU-Russia energy security regime in terms of interdependence theory

Energy Technology Data Exchange (ETDEWEB)

Esakova, Nataliya

2012-07-01

Nataliya Esakova performs an analysis of the interdependencies and the nature of cooperation between energy producing, consuming and transit countries focusing on the gas sector. For the analysis the theoretical framework of the interdependence theory by Robert O. Keohane and Joseph S. Nye and the international regime theory are applied to the recent developments within the gas relationship between the European Union and Russia in the last decade. The objective of the analysis is to determine, whether a fundamental regime change in terms of international regime theory is taking place, and, if so, which regime change explanation model in terms of interdependence theory is likely to apply. (orig.)

Flow Regimes of Air-Water Counterflow Through Cross Corrugated Parallel Plates

Energy Technology Data Exchange (ETDEWEB)

de Almeida, V.F.

2000-06-07

Heretofore unknown flow regimes of air-water counterflow through a pair of transparent vertical parallel cross corrugated plates were observed via high-speed video. Air flows upward driven by pressure gradient and water, downward driven by gravity. The crimp geometry of the corrugations was drawn from typical corrugated sheets used as filling material in modern structured packed towers. Four regimes were featured, namely, rivulet, bicontinuous, flooding fronts, and flooding waves. It is conceivable that the regimes observed might constitute the basis for understanding how gas and liquid phases contend for available space in the interstices of structured packings in packed towers. Flow regime transitions were expressed in terms of liquid load (liquid superficial velocity) and gas flow factor parameters commonly used in pressure drop and capacity curves. We have carefully examined the range of parameters equivalent to the ill-understood high-liquid-flow operation in packed towers. More importantly, our findings should prove valuable in validating improved first-principles modeling of gas-liquid flows in these industrially important devices.

Determination of the Hall Thruster Operating Regimes

International Nuclear Information System (INIS)

L. Dorf; V. Semenov; Y. Raitses; N.J. Fisch

2002-04-01

A quasi one-dimensional (1-D) steady-state model of the Hall thruster is presented. For the same discharge voltage two operating regimes are possible -- with and without the anode sheath. For given mass flow rate, magnetic field profile and discharge voltage a unique solution can be constructed, assuming that the thruster operates in one of the regimes. However, we show that for a given temperature profile the applied discharge voltage uniquely determines the operating regime: for discharge voltages greater than a certain value, the sheath disappears. That result is obtained over a wide range of incoming neutral velocities, channel lengths and widths, and cathode plane locations. It is also shown that a good correlation between the quasi 1-D model and experimental results can be achieved by selecting an appropriate electron mobility and temperature profile

Flow regimes

International Nuclear Information System (INIS)

Kh'yuitt, G.

1980-01-01

An introduction into the problem of two-phase flows is presented. Flow regimes arizing in two-phase flows are described, and classification of these regimes is given. Structures of vertical and horizontal two-phase flows and a method of their identification using regime maps are considered. The limits of this method application are discussed. The flooding phenomena and phenomena of direction change (flow reversal) of the flow and interrelation of these phenomena as well as transitions from slug regime to churn one and from churn one to annular one in vertical flows are described. Problems of phase transitions and equilibrium are discussed. Flow regimes in tubes where evaporating liquid is running, are described [ru

AnSBBR with circulation applied to biohydrogen production treating sucrose based wastewater: effects of organic loading, influent concentration and cycle length

Directory of Open Access Journals (Sweden)

D. A. Santos

2014-09-01

Full Text Available An anaerobic sequencing batch biofilm reactor (AnSBBR containing immobilized biomass and operating with recirculation of the liquid phase (total liquid volume 4.5 L; treated volume per cycle 1.9 L was used to treat sucrose-based wastewater at 30 ºC and produce biohydrogen. The influence of applied volumetric organic load was studied by varying the influent concentration at 3600 and 5400 mgCOD.L-1 and using cycle lengths of 4, 3 and 2 hours, obtaining in this manner volumetric organic loads of 9, 12, 13.5, 18 and 27 gCOD.L-1.d-1. Different performance indicators were used: productivity and yield of biohydrogen per applied and removed load, reactor stability and efficiency based on the applied and removed organic loads, both in terms of organic matter (measured as COD and carbohydrate (sucrose. The results revealed system stability (32-37% of H2 in biogas during biohydrogen production, as well as substrate consumption (12-19% COD; 97-99% sucrose. Conversion efficiencies decreased when the influent concentration was increased (at constant cycle length and when cycle lengths were reduced (at constant influent concentrations. The best yield was 4.16 mol-H2.kg-SUC-1 (sucrose load at 9 gCOD.L-1.d-1 (3600 mgCOD.L-1 and 4 h with H2 content in the biogas of 36% (64% CO2 and 0% CH4. However, the best specific molar productivity of hydrogen was 8.5 molH2.kgTVS-1.d-1 (32% H2; 68% CO2; 0% CH4, at 18 gCOD.L-1.d-1 (5400 mgCOD.L-1 and 3 h, indicating that the best productivity tends to occur at higher organic loads, as this parameter involves the "biochemical generation" of biogas, whereas the best yield tends to occur at lower and/or intermediate organic loads, as this parameter involves "biochemical consumption" of the substrate. The most significant metabolites were ethanol, acetic acid and butyric acid. Microbiological analyses revealed that the biomass contained bacilli and endospore filaments and showed no significant variations in morphology between

Computational characterization of ignition regimes in a syngas/air mixture with temperature fluctuations

KAUST Repository

Pal, Pinaki; Valorani, Mauro; Arias, Paul G.; Im, Hong G.; Wooldridge, Margaret S.; Ciottoli, Pietro P.; Galassi, Riccardo M.

2016-01-01

) was applied to characterize the auto-ignition phenomena. All results supported that the observed ignition behaviors were consistent with the expected ignition regimes predicted by the theory of the regime diagram. This work provides new high-fidelity data

Dynamical Model of Rocket Propellant Loading with Liquid Hydrogen

Data.gov (United States)

National Aeronautics and Space Administration — A dynamical model describing the multi-stage process of rocket propellant loading has been developed. It accounts for both the nominal and faulty regimes of...

Fatigue damage behavior of a surface-mount electronic package under different cyclic applied loads

Science.gov (United States)

Ren, Huai-Hui; Wang, Xi-Shu

2014-04-01

This paper studies and compares the effects of pull-pull and 3-point bending cyclic loadings on the mechanical fatigue damage behaviors of a solder joint in a surface-mount electronic package. The comparisons are based on experimental investigations using scanning electron microscopy (SEM) in-situ technology and nonlinear finite element modeling, respectively. The compared results indicate that there are different threshold levels of plastic strain for the initial damage of solder joints under two cyclic applied loads; meanwhile, fatigue crack initiation occurs at different locations, and the accumulation of equivalent plastic strain determines the trend and direction of fatigue crack propagation. In addition, simulation results of the fatigue damage process of solder joints considering a constitutive model of damage initiation criteria for ductile materials and damage evolution based on accumulating inelastic hysteresis energy are identical to the experimental results. The actual fatigue life of the solder joint is almost the same and demonstrates that the FE modeling used in this study can provide an accurate prediction of solder joint fatigue failure.

A study on fatigue crack growth model considering high mean loading effects based on structural stress

International Nuclear Information System (INIS)

Kim, Jong Sung; Kim, Cheol; Jin, Tae Eun; Dong, P.

2004-01-01

The mesh-insensitive structural stress procedure by Dong is modified to apply to the welded joints with local thickness variation and inarguable shear/normal stresses along local discontinuity surface. In order to make use of the structural stress based K solution for fatigue correlation of welded joints, a proper crack growth model needs to be developed. There exist some significant discrepancies in inferring the slope or crack growth exponent in the conventional Paris law regime. Two-stage crack growth model was not considered since its applications are focused upon the fatigue behavior in welded joints in which the load ratio effects are considered negligible. In this paper, a two-stage crack growth law considering high mean loading is proposed and proven to be effective in unifying the so-called anomalous short crack growth data

Large deformation of uniaxially loaded slender microbeams on the basis of modified couple stress theory: Analytical solution and Galerkin-based method

Science.gov (United States)

Kiani, Keivan

2017-09-01

Large deformation regime of micro-scale slender beam-like structures subjected to axially pointed loads is of high interest to nanotechnologists and applied mechanics community. Herein, size-dependent nonlinear governing equations are derived by employing modified couple stress theory. Under various boundary conditions, analytical relations between axially applied loads and deformations are presented. Additionally, a novel Galerkin-based assumed mode method (AMM) is established to solve the highly nonlinear equations. In some particular cases, the predicted results by the analytical approach are also checked with those of AMM and a reasonably good agreement is reported. Subsequently, the key role of the material length scale on the load-deformation of microbeams is discussed and the deficiencies of the classical elasticity theory in predicting such a crucial mechanical behavior are explained in some detail. The influences of slenderness ratio and thickness of the microbeam on the obtained results are also examined. The present work could be considered as a pivotal step in better realizing the postbuckling behavior of nano-/micro- electro-mechanical systems consist of microbeams.

Study and optimization of operating regimes of NPP district heating system

International Nuclear Information System (INIS)

Bunin, V.S.; Vasil'ev, M.K.; Kudryavtsev, A.A.; Gorbashev, Yu.B.; Gadzhij, V.M.

1980-01-01

Thermal tests of the system with two reactors and four turbines have been carried out for the purpose of verification of operating regimes of the NPP district heating system with boiling single-curcuit RBMK-1000 reactors and K-500-65/3000 turbines. The system is designed for heat supply of habitable settlement and industrial site. The data processing have been carried out by the BESM-6 computer representing distributions of heat flow, steam, water and their parameters and determining the main energy indices of the system. Calculations of the system operating regime variables during the year have been carried out with the help of this program. It has been expected that the system provided heat consumption of 232 MW at calculated regime of thermal loading of the district, temperature regime of the system water of 130/170 deg C, relative load of hot water supply of 0.2 and duration of heating period of 4800 h. Calculations demonstrated that distric heat supply by NPP allowed one to supplant about 85 thous. of reference fuel/year of organic fuel. About 63 thous. of reference fuel/year are required for compensation of decrease of electric energy production in a condensation cycle. It has been also shown, that replacing the four-stroke system heaters by one-stroke heaters permits to drop system water underheating 1.5 times and, respectively, electric energy underproduction to 72 mln Mj (20 mln, kWxh). It produces additional economy of 6.6 thous. reference fuel/year. Calculations of its heat system have been conducted in order to determine the influence of water consumption in an intermediate circuit on the system efficiency. It has been shown that with the increase of water consumption energy power losses decrease. Thus, the above studied have demonstrated that the use of the single-circuit NPP district heating systems leads to considerable economy of fuel

An Examination of the Nature of Global MODIS Cloud Regimes

Science.gov (United States)

Oreopoulos, Lazaros; Cho, Nayeong; Lee, Dongmin; Kato, Seiji; Huffman, George J.

2014-01-01

We introduce global cloud regimes (previously also referred to as "weather states") derived from cloud retrievals that use measurements by the Moderate Resolution Imaging Spectroradiometer (MODIS) instrument aboard the Aqua and Terra satellites. The regimes are obtained by applying clustering analysis on joint histograms of retrieved cloud top pressure and cloud optical thickness. By employing a compositing approach on data sets from satellites and other sources, we examine regime structural and thermodynamical characteristics. We establish that the MODIS cloud regimes tend to form in distinct dynamical and thermodynamical environments and have diverse profiles of cloud fraction and water content. When compositing radiative fluxes from the Clouds and the Earth's Radiant Energy System instrument and surface precipitation from the Global Precipitation Climatology Project, we find that regimes with a radiative warming effect on the atmosphere also produce the largest implied latent heat. Taken as a whole, the results of the study corroborate the usefulness of the cloud regime concept, reaffirm the fundamental nature of the regimes as appropriate building blocks for cloud system classification, clarify their association with standard cloud types, and underscore their distinct radiative and hydrological signatures.

Dynamics of skyrmions and edge states in the resistive regime of mesoscopic p-wave superconductors

Energy Technology Data Exchange (ETDEWEB)

Fernández Becerra, V., E-mail: VictorLeonardo.FernandezBecerra@uantwerpen.be; Milošević, M.V., E-mail: milorad.milosevic@uantwerpen.be

2017-02-15

Highlights: • Voltage–current characterization of a mesoscopic p-wave superconducting sample. • Skyrmions and edge states are stabilized with an out-of-plane applied magnetic field. • In the resistive regime, moving skyrmions and the edge state behave distinctly different from the conventional kinematic vortices. - Abstract: In a mesoscopic sample of a chiral p-wave superconductor, novel states comprising skyrmions and edge states have been stabilized in out-of-plane applied magnetic field. Using the time-dependent Ginzburg–Landau equations we shed light on the dynamic response of such states to an external applied current. Three different regimes are obtained, namely, the superconducting (stationary), resistive (non-stationary) and normal regime, similarly to conventional s-wave superconductors. However, in the resistive regime and depending on the external current, we found that moving skyrmions and the edge state behave distinctly different from the conventional kinematic vortex, thereby providing new fingerprints for identification of p-wave superconductivity.

Original analytical model of the hydrodynamic loads applied on the half-bridge of a circular settling tank

Science.gov (United States)

Oanta, Emil M.; Dascalescu, Anca-Elena; Sabau, Adrian

2016-12-01

The paper presents an original analytical model of the hydrodynamic loads applied on the half-bridge of a circular settling tank. The calculus domain is defined using analytical geometry and the calculus of the local dynamic pressure is based on the radius from the center of the settling tank to the current area, i.e. the relative velocity of the fluid and the depth where the current area is located, i.e. the density of the fluid. Calculus of the local drag forces uses the discrete frontal cross sectional areas of the submerged structure in contact with the fluid. In the last stage is performed the reduction of the local drag forces in the appropriate points belonging to the main beam. This class of loads is producing the flexure of the main beam in a horizontal plane and additional twisting moments along this structure. Taking into account the hydrodynamic loads, the results of the theoretical models, i.e. the analytical model and the finite element model, may have an increased accuracy.

COMPARATIVE STUDY OF THREE LINEAR SYSTEM SOLVER APPLIED TO FAST DECOUPLED LOAD FLOW METHOD FOR CONTINGENCY ANALYSIS

Directory of Open Access Journals (Sweden)

Syafii

2017-03-01

Full Text Available This paper presents the assessment of fast decoupled load flow computation using three linear system solver scheme. The full matrix version of the fast decoupled load flow based on XB methods used in this study. The numerical investigations are carried out on the small and large test systems. The execution time of small system such as IEEE 14, 30, and 57 are very fast, therefore the computation time can not be compared for these cases. Another cases IEEE 118, 300 and TNB 664 produced significant execution speedup. The superLU factorization sparse matrix solver has best performance and speedup of load flow solution as well as in contigency analysis. The invers full matrix solver can solved only for IEEE 118 bus test system in 3.715 second and for another cases take too long time. However for superLU factorization linear solver can solved all of test system in 7.832 second for a largest of test system. Therefore the superLU factorization linear solver can be a viable alternative applied in contingency analysis.

The Reusable Load Cell with Protection Applied for Online Monitoring of Overhead Transmission Lines Based on Fiber Bragg Grating

Directory of Open Access Journals (Sweden)

Guoming Ma

2016-06-01

Full Text Available Heavy ice coating of high–voltage overhead transmission lines may lead to conductor breakage and tower collapse causing the unexpected interrupt of power supply. The optical load cell applied in ice monitoring systems is immune to electromagnetic interference and has no need of a power supply on site. Therefore, it has become a hot research topic in China and other countries. In this paper, to solve the problem of eccentric load in measurement, we adopt the shearing structure with additional grooves to improve the strain distribution and acquire good repeatability. Then, the fiber Bragg grating (FBG with a permanent weldable package are mounted onto the front/rear groove of the elastic element by spot welding, the direction deviation of FBGs is 90° from each other to achieve temperature compensation without an extra FBG. After that, protection parts are designed to guarantee high sensitivity for a light load condition and industrial safety under a heavy load up to 65 kN. The results of tension experiments indicate that the sensitivity and resolution of the load cell is 0.1285 pm/N and 7.782 N in the conventional measuring range (0–10 kN. Heavy load tension experiments prove that the protection structure works and the sensitivity and resolution are not changed after several high load (65 kN cycles. In addition, the experiment shows that the resolution of the sensor is 87.79 N in the large load range, allowing the parameter to be used in heavy icing monitoring.

Conditional Stochastic Processes Applied to Wave Load Predictions

DEFF Research Database (Denmark)

Jensen, Jørgen Juncher

2015-01-01

The concept of conditional stochastic processes provides a powerful tool for evaluation and estimation of wave loads on ships and offshore structures. This article first considers conditional waves with a focus on critical wave episodes. Then the inherent uncertainty in the results is illustrated...

Water regime of steam power plants

International Nuclear Information System (INIS)

Oesz, Janos

2011-01-01

The water regime of water-steam thermal power plants (secondary side of pressurized water reactors (PWR); fossil-fired thermal power plants - referred to as steam power plants) has changed in the past 30 years, due to a shift from water chemistry to water regime approach. The article summarizes measures (that have been realised by chemists of NPP Paks) on which the secondary side of NPP Paks has become a high purity water-steam power plant and by which the water chemistry stress corrosion risk of heat transfer tubes in the VVER-440 steam generators was minimized. The measures can also be applied to the water regime of fossil-fired thermal power plants with super- and subcritical steam pressure. Based on the reliability analogue of PWR steam generators, water regime can be defined as the harmony of construction, material(s) and water chemistry, which needs to be provided in not only the steam generators (boiler) but in each heat exchanger of steam power plant: - Construction determines the processes of flow, heat and mass transfer and their local inequalities; - Material(s) determines the minimal rate of general corrosion and the sensitivity for local corrosion damage; - Water chemistry influences the general corrosion of material(s) and the corrosion products transport, as well as the formation of local corrosion environment. (orig.)

Applying a Stiffened Stitched Concept to Shear-Loaded Structure

Science.gov (United States)

Jegley, Dawn C.

2014-01-01

NASA and The Boeing Company have worked to develop new low-cost, lightweight composite structures for aircraft. A stitched carbon-epoxy material system was developed to reduce the weight and cost of transport aircraft structure, first in the NASA Advanced Composites Technology (ACT) Program in the 1990's and now in the Environmentally Responsible Aviation (ERA) Project. By stitching through the thickness of a dry carbon fiber material prior to cure, the need for mechanical fasteners is almost eliminated. Stitching also provides the benefit of reducing or eliminating delaminations, including those between stiffener flanges and skin. The stitched panel concept used in the ACT program used simple blade-stiffeners as stringers, caps, and clips. Today, the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept is being developed for application to advanced vehicle configurations. PRSEUS provides additional weight savings through the use of a stiffener with a thin web and a unidirectional carbon rod at the top of the web which provides structurally efficient stiffening. Comparisons between stitched and unstitched structure and between blade-stiffened and rod-stiffened structure are presented focusing on a panel loaded in shear. Shear loading is representative of spar loading in wing structures.

Determination of the Hall Thruster Operating Regimes; TOPICAL

International Nuclear Information System (INIS)

L. Dorf; V. Semenov; Y. Raitses; N.J. Fisch

2002-01-01

A quasi one-dimensional (1-D) steady-state model of the Hall thruster is presented. For the same discharge voltage two operating regimes are possible - with and without the anode sheath. For given mass flow rate, magnetic field profile and discharge voltage a unique solution can be constructed, assuming that the thruster operates in one of the regimes. However, we show that for a given temperature profile the applied discharge voltage uniquely determines the operating regime: for discharge voltages greater than a certain value, the sheath disappears. That result is obtained over a wide range of incoming neutral velocities, channel lengths and widths, and cathode plane locations. It is also shown that a good correlation between the quasi 1-D model and experimental results can be achieved by selecting an appropriate electron mobility and temperature profile

The history, development and application of a uniformly applied load wide plate testing machine

International Nuclear Information System (INIS)

Quirk, A.; Bevitt, E.

1989-01-01

The paper describes early attempts to use a rigid end wide plate testing machine to investigate the behaviour of centre cracked flat plates. Confusing and inconsistent results arising from the above tests lead to a detailed investigation of the loading characteristics of rigid end machines in general and the difficulties which can arise in the interpretation of data obtained by the use of such machines. In order to overcome the above difficulties which stem largely from uneven load distribution, a versatile testing machine was designed which by use of cheap and easily obtainable components allows the application of a uniformly distributed applied load to a centre cracked test plate. The machine which was commissioned in its original form in 1975 was initially capable of testing plate of 820 mm width and 25 or 48 mm thickness up to maximum stress levels of 488 or 254 MPa respectively. The ease of adaptability of the machine has since permitted its capacity to be increased to handle plate up to 2032 mm wide and 76 mm thickness and by use of double-banked hydraulic jacks stress levels up to 350 MPa can be achieved on plate of these dimensions. The configuration of the machine allows adequate access for strain gauging, crack tip observation and measurements, and temperature control, tests having been conducted in the temperature range -40 0 C to 290 0 C. Advantages and potential for further development of the machine are given together with details of two of a number of fracture studies which have been conducted since its commissioning. (orig.)

Study of a spur gear dynamic behavior in transient regime

Science.gov (United States)

Khabou, M. T.; Bouchaala, N.; Chaari, F.; Fakhfakh, T.; Haddar, M.

2011-11-01

In this paper the dynamic behavior of a single stage spur gear reducer in transient regime is studied. Dynamic response of the single stage spur gear reducer is investigated at different rotating velocities. First, gear excitation is induced by the motor torque and load variation in addition to the fluctuation of meshing stiffness due to the variation of input rotational speed. Then, the dynamic response is computed using the Newmark method. After that, a parameter study is made on spur gear powered in the first place by an electric motor and in the second place by four strokes four cylinders diesel engine. Dynamic responses come to confirm a significant influence of the transient regime on the dynamic behavior of a gear set, particularly in the case of engine acyclism condition.

Loading capacities and failure modes of various reinforced concrete slabs subjected to high-speed loading

International Nuclear Information System (INIS)

Saito, H.; Imamura, A.; Takeuchi, M.; Okamoto, S.; Kasai, Y.; Tsubota, H.; Yoshimura, M.

1993-01-01

The objective of this study was to clarify experimentally and analytically the loading capacities, deformations and failure modes of various types of reinforced concrete structures subjected to loads applied at various loading rates. Flat slabs, slabs with beams and cylindrical walls were tested under static, low-speed and high-speed loading. Analysis was applied to estimate the test results by the finite element method using a layered shell element. The analysis closely simulated the experimental results until punching shear failure occurred. (author)

Regime switching state-space models applied to psychological processes: handling missing data and making inferences

NARCIS (Netherlands)

Hamaker, E.L.; Grasman, R.P.P.P.

2012-01-01

Many psychological processes are characterized by recurrent shifts between distinct regimes or states. Examples that are considered in this paper are the switches between different states associated with premenstrual syndrome, hourly fluctuations in affect during a major depressive episode, and

Methodology for the selection of the regime of flow in lagoons of stabilization

International Nuclear Information System (INIS)

Cruz T, Luis Eduardo; Alayon Torres, Walter E; Monsegny S, Carlos Emilio

2000-01-01

To model biological processes, information is needed on the stoichiometry and kinetics of the reactions and about the hydraulic regime of the system. The stoichiometry of a reaction refers to the quantity of consumed reactants (such as substrates) and to the quantity of formed products (such as microorganisms). The hydraulic regime makes reference to the configuration of the flow inside of and outside of the process and to the mixture and distribution of the solids of the fluid inside the reactor. The present article it is centered in studying the different mixture regimens and its kinetic models of degradation of organic matter applied to the case specify of the lagoon of stabilization of residual waters of the Municipality of Tocancipa; also it the methodology discusses to determine the type of flow that is presented in a stabilization lagoon. The kinetic models of degradation of organic matter in stabilization lagoons are classified according with the presence or absence of oxygen in the lagoon and with the mixture regime that it is presented in this. The regimens of flow that are presented in the stabilization lagoons are those of complete mixture and the piston flow, one completely opposed to the other one. Between these two is the denominated regime of dispersed or arbitrary flow. The determination of the mixture regime is of great importance, since with this it is possible to have an idea of the behavior of the rates of removal of the nutrients that arrive to the system, of the consumption of oxygen and the kinetic pattern of removal of organic matter among others. The regime of mixture complete ideal this characterized because the mass of water that enters to the system is dispersed instantly, making that the characteristics of the water are the same ones in any point, that is to say that the reaction rates are constant in the reactor and the demand of oxygen it is identical in any sampling point, likewise it happens with the removal rate; this has big

Liquid aerosol filtration by fibrous filters in interception and inertial regimes; Filtration des aerosols liquides par les filtres a fibres en regimes d`interception et d`inertie

Energy Technology Data Exchange (ETDEWEB)

Gougeon, R

1994-09-26

In most previous studies of aerosol filtration, attention is focused on the maximum penetrating particle size region where the predominant mechanisms for collection are brownian diffusion and interception. In contrary the inertial regime remains poorly understood. Therefore, the aim of this study was to improve understanding of the behaviour of fibrous filters with liquid aerosols ar high frontal velocities both in the stationary and nonstationary filtration. Stationary filtration is first investigated. Experiments are done with special filters called `formettes` which have well defined structural characteristics. Precise results obtained with those filters allow us to select two relations quoted in the literature in order to describe the diffusion and the interception and to determine an empirical correlation describing the inertial impaction. Then this correlation with an industrial filter. In the second part, the evolution of the performances of fibrous filters loaded with liquid aerosols is studied experimentally and theoretically. We show that, in the inertial regime the filter efficiency first decreases and then increases rapidly with the loading rate. This increase is particularly important at high frontal velocities and with big particles. Macroscopic observations of high loaded filters show that the liquid is located in the fibre`s intersections to form big flat surfaces. A tentative of describing the evolution of the filter efficiency in modifying our stationary filtration model in order to take into account those liquid surfaces in the filter gives encouraging results. (authors). 92 refs., 93 figs., 11 tabs., 4 appends.

Power Load Prediction Based on Fractal Theory

OpenAIRE

Jian-Kai, Liang; Cattani, Carlo; Wan-Qing, Song

2015-01-01

The basic theories of load forecasting on the power system are summarized. Fractal theory, which is a new algorithm applied to load forecasting, is introduced. Based on the fractal dimension and fractal interpolation function theories, the correlation algorithms are applied to the model of short-term load forecasting. According to the process of load forecasting, the steps of every process are designed, including load data preprocessing, similar day selecting, short-term load forecasting, and...

Neonatal mannequin comparison of the Upright self-inflating bag and snap-fit mask versus standard resuscitators and masks: leak, applied load and tidal volumes.

Science.gov (United States)

Rafferty, Anthony Richard; Johnson, Lucy; Davis, Peter G; Dawson, Jennifer Anne; Thio, Marta; Owen, Louise S

2017-11-30

Neonatal mask ventilation is a difficult skill to acquire and maintain. Mask leak is common and can lead to ineffective ventilation. The aim of this study was to determine whether newly available neonatal self-inflating bags and masks could reduce mask leak without additional load being applied to the face. Forty operators delivered 1 min episodes of mask ventilation to a mannequin using the Laerdal Upright Resuscitator, a standard Laerdal infant resuscitator (Laerdal Medical) and a T-Piece Resuscitator (Neopuff), using both the Laerdal snap-fit face mask and the standard Laerdal size 0/1 face mask (equivalent sizes). Participants were asked to use pressure sufficient to achieve 'appropriate' chest rise. Leak, applied load, airway pressure and tidal volume were measured continuously. Participants were unaware that load was being recorded. There was no difference in mask leak between resuscitation devices. Leak was significantly lower when the snap-fit mask was used with all resuscitation devices, compared with the standard mask (14% vs 37% leak, Pmask was preferred by 83% of participants. The device-mask combinations had no significant effect on applied load. The Laerdal Upright Resuscitator resulted in similar leak to the other resuscitation devices studied, and did not exert additional load to the face and head. The snap-fit mask significantly reduced overall leak with all resuscitation devices and was the mask preferred by participants. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Research of Impact Load in Large Electrohydraulic Load Simulator

Directory of Open Access Journals (Sweden)

Yongguang Liu

2014-01-01

Full Text Available The stronger impact load will appear in the initial phase when the large electric cylinder is tested in the hardware-in-loop simulation. In this paper, the mathematical model is built based on AMESim, and then the reason of the impact load is investigated through analyzing the changing tendency of parameters in the simulation results. The inhibition methods of impact load are presented according to the structural invariability principle and applied to the actual system. The final experimental result indicates that the impact load is inhibited, which provides a good experimental condition for the electric cylinder and promotes the study of large load simulator.

Extending the collisional fluid equations into the long mean-free-path regime in toroidal plasmas. IV. Banana regime

International Nuclear Information System (INIS)

Shaing, K. C.

2007-01-01

In Part I [Phys. Fluids B 2, 1190 (1990)] and Part II [Phys. Plasmas 12, 082508 (2005)], it was emphasized that the equilibrium plasma viscous forces when applied for the magnetohydrodynamic (MHD) modes are only rigorously valid at the mode rational surface where m-nq=0. Here, m is the poloidal mode number, n is the toroidal mode number, and q is the safety factor. This important fact has been demonstrated explicitly by calculating the viscous forces in the plateau regime in Parts I and II. Here, the effective viscous forces in the banana regime are calculated for MHD modes by solving the linear drift kinetic equation that is driven by the plasma flows first derived in Part I. At the mode rational surface, the equilibrium plasma viscous forces are reproduced. However, it is found that away from the mode rational surface, the viscous forces for MHD modes decrease, a behavior similar to that observed in the viscous forces for the plateau regime. The proper form of the momentum equation that is appropriate for the modeling of the MHD modes is also discussed

Ratcheting of pressurized piping subjected to seismic loading

International Nuclear Information System (INIS)

Scavuzzo, R.J.; Lam, P.C.; Gau, J.S.

1992-01-01

The ABAQUS finite element code was used to model a pressurized pipe and subjected to cyclic bending loads to investigate ratcheting. A 1-in. schedule 40 pipe was loaded with a slow (static) cyclic load. The pipe internal pressure was varied from 0 to 6000 psi. In this paper, two types of materials were considered: an elastic perfectly plastic and a bilinear elastic-plastic material. Two types of finite elements of the ABAQUS program were compared to analytical solutions to evaluate the element accuracy in the plastic regime. Depending upon loading conditions and specified material properties, three different responses were observed from the finite element analyses: cyclic plasticity, ratcheting of the hoop strain, or shakedown. These analytical results are compared to some experimental measurements

Dynamics of levitated nanospheres: towards the strong coupling regime

International Nuclear Information System (INIS)

Monteiro, T S; Millen, J; Pender, G A T; Barker, P F; Marquardt, Florian; Chang, D

2013-01-01

The use of levitated nanospheres represents a new paradigm for the optomechanical cooling of a small mechanical oscillator, with the prospect of realizing quantum oscillators with unprecedentedly high quality factors. We investigate the dynamics of this system, especially in the so-called self-trapping regime, where one or more optical fields simultaneously trap and cool the mechanical oscillator. The determining characteristic of this regime is that both the mechanical frequency ω M and single-photon optomechanical coupling strength parameters g are a function of the optical field intensities, in contrast to usual set-ups where ω M and g are constant for the given system. We also measure the characteristic transverse and axial trapping frequencies of different sized silica nanospheres in a simple optical standing wave potential, for spheres of radii r = 20–500 nm, illustrating a protocol for loading single nanospheres into a standing wave optical trap that would be formed by an optical cavity. We use these data to confirm the dependence of the effective optomechanical coupling strength on sphere radius for levitated nanospheres in an optical cavity and discuss the prospects for reaching regimes of strong light–matter coupling. Theoretical semiclassical and quantum displacement noise spectra show that for larger nanospheres with r ∼> 100 nm a range of interesting and novel dynamical regimes can be accessed. These include simultaneous hybridization of the two optical modes with the mechanical modes and parameter regimes where the system is bistable. We show that here, in contrast to typical single-optical mode optomechanical systems, bistabilities are independent of intracavity intensity and can occur for very weak laser driving amplitudes. (paper)

Dynamic analysis of double-row self-aligning ball bearings due to applied loads, internal clearance, surface waviness and number of balls

Science.gov (United States)

Zhuo, Yaobin; Zhou, Xiaojun; Yang, Chenlong

2014-11-01

In this paper, a three degrees of freedom (dof) model was established for a double-row self-aligning ball bearing (SABB) system, and was applied to study the dynamic behavior of the system during starting process and constant speed rotating process. A mathematical model was developed concerning stiffness and damping characteristics of the bearing, as well as three-dimensional applied load, rotor centrifugal force, etc. Balls and races were all considered as nonlinear springs, and the contact force between ball and race was calculated based on classic Hertzian elastic contact deformation theory and deformation compatibility theory. The changes of each ball's contact force and loaded angle of each row were taken into account. In order to solve the nonlinear dynamical equilibrium equations of the system, these equations were rewritten as differential equations and the fourth order Runge-Kutta method was used to solve the equations iteratively. In order to verify accuracy of the dynamical model and correctness of the numerical solution method, a kind of SABB-BRF30 was chosen for case studies. The effects of several important governing parameters, such as radial and axial applied loads, normal internal, inner and outer races waviness, and number of balls were investigated. These parametric studies led to a complete characterization of the shaft-bearing system vibration transmission. The research provided a theoretical reference for new type bearing design, shaft-bearing system kinetic analysis, optimal design, etc.

BGK-type models in strong reaction and kinetic chemical equilibrium regimes

International Nuclear Information System (INIS)

Monaco, R; Bianchi, M Pandolfi; Soares, A J

2005-01-01

A BGK-type procedure is applied to multi-component gases undergoing chemical reactions of bimolecular type. The relaxation process towards local Maxwellians, depending on mass and numerical densities of each species as well as common velocity and temperature, is investigated in two different cases with respect to chemical regimes. These cases are related to the strong reaction regime characterized by slow reactions, and to the kinetic chemical equilibrium regime where fast reactions take place. The consistency properties of both models are stated in detail. The trend to equilibrium is numerically tested and comparisons for the two regimes are performed within the hydrogen-air and carbon-oxygen reaction mechanism. In the spatial homogeneous case, it is also shown that the thermodynamical equilibrium of the models recovers satisfactorily the asymptotic equilibrium solutions to the reactive Euler equations

Immune networks: multi-tasking capabilities at medium load

Science.gov (United States)

Agliari, E.; Annibale, A.; Barra, A.; Coolen, A. C. C.; Tantari, D.

2013-08-01

Associative network models featuring multi-tasking properties have been introduced recently and studied in the low-load regime, where the number P of simultaneously retrievable patterns scales with the number N of nodes as P ˜ log N. In addition to their relevance in artificial intelligence, these models are increasingly important in immunology, where stored patterns represent strategies to fight pathogens and nodes represent lymphocyte clones. They allow us to understand the crucial ability of the immune system to respond simultaneously to multiple distinct antigen invasions. Here we develop further the statistical mechanical analysis of such systems, by studying the medium-load regime, P ˜ Nδ with δ ∈ (0, 1]. We derive three main results. First, we reveal the nontrivial architecture of these networks: they exhibit a high degree of modularity and clustering, which is linked to their retrieval abilities. Second, by solving the model we demonstrate for δ frameworks are required to achieve effective retrieval.

Code systems for effective and precise calculation of the basic neutron characteristics, core loading optimization, analysis and estimation of the operation regimes of WWER type reactors

International Nuclear Information System (INIS)

Apostolov, T.; Ivanov, K.; Prodanova, R.; Manolova, M.; Petrova, T.; Alekova, G.

1993-01-01

Two directions for investigations are suggested: 1) Analysis and evaluation of the real loading patterns and operational regimes for Kozloduy NPP WWER-440 and WWER-1000 in the frame of the recent safety criteria and nuclear power plant operating limits. 2) Development of modern code system for WWER type reactor core analysis with advanced features: new design and materials for fuel and control rods, increasing the fuel enrichment, using the integral and discrete burnable absorbers etc. The fuel technology design evolution maximizes the fuel utilization efficiency, improves operation performance and enhances safety margins. By the joint efforts of specialists from INRNE, Sofia (BG) and KAB, Berlin (GE), the codes NESSEL-IV-EC, PYTHIA and DERAB have been developed and verified. In the frame of the PHARE programme the joint project ASPERCA has been proposed intended for reactor physics calculations with PHYBER-WWER code for safety enhancement and operation reliability improvement. In-core fuel management benchmarks for 4 cycles of unit 2 (WWER-440) and 2 cycles of unit 5 (WWER-1000) have been performed. The coordination of burnable absorber design implementation, low leakage loadings usage, reloading enrichment increase and steel content reduction in the core have made the reactor core analysis more demanding and the definition of loading patterns - more difficult. This complexity requires routine use of three-dimensional fast accurate core model with extended and updated cross section libraries. To meet the needs of WWER advanced loading patterns and in-core fuel management improvements the HEXANES code systems is being developed and qualified. Some test calculations have been carried out by the HEXANES code system investigating the influence of Gd in the fuel on the main reactor physics parameters. For reevaluation of the core safety-related design limits forming the basis of licensing procedure, the code DYN3D/M2 is used. 16 refs., 3 figs. (author)

Layer-dependent role of collagen recruitment during loading of the rat bladder wall.

Science.gov (United States)

Cheng, Fangzhou; Birder, Lori A; Kullmann, F Aura; Hornsby, Jack; Watton, Paul N; Watkins, Simon; Thompson, Mark; Robertson, Anne M

2018-04-01

In this work, we re-evaluated long-standing conjectures as to the source of the exceptionally large compliance of the bladder wall. Whereas these conjectures were based on indirect measures of loading mechanisms, in this work we take advantage of advances in bioimaging to directly assess collagen fibers and wall architecture during biaxial loading. A custom biaxial mechanical testing system compatible with multiphoton microscopy was used to directly measure the layer-dependent collagen fiber recruitment in bladder tissue from 9 male Fischer rats (4 adult and 5 aged). As for other soft tissues, the bladder loading curve was exponential in shape and could be divided into toe, transition and high stress regimes. The relationship between collagen recruitment and loading curves was evaluated in the context of the inner (lamina propria) and outer (detrusor smooth muscle) layers. The large extensibility of the bladder was found to be possible due to folds in the wall (rugae) that provide a mechanism for low resistance flattening without any discernible recruitment of collagen fibers throughout the toe regime. For more extensible bladders, as the loading extended into the transition regime, a gradual coordinated recruitment of collagen fibers between the lamina propria layer and detrusor smooth muscle layer was found. A second important finding was that wall extensibility could be lost by premature recruitment of collagen in the outer wall that cut short the toe region. This change was correlated with age. This work provides, for the first time, a mechanistic understanding of the role of collagen recruitment in determining bladder extensibility and capacitance.

Energy saving in the auxiliaries consumption for circulation water pumps optimizing the thermal regime; Ahorro en el consumo de auxiliares por bombas de agua de circulacion optimando el regimen termico

Energy Technology Data Exchange (ETDEWEB)

Orozco Martinez, Roni [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1999-12-31

A methodology is proposed that should be followed in any thermal electric power plant to determine the load value at which a unit requires a second circulation water pump without affecting the thermal regime and avoiding an excessive auxiliaries consumption in partial loads. In applying this method the power plant would have an energy saving equivalent to the auxiliaries consumption during an hour, when the unit as operating at full load. [Espanol] Se propone una metodologia que debe seguirse en cualquier central termoelectrica para determinar el valor de la carga en la cual una unidad requiere de la segunda bomba de agua de circulacion sin afectar el regimen termico y evitadose un excesivo consumo de auxiliares en cargas parciales. Al aplicar este metodo la central tendria un ahorro de energia equivalente al consumo de auxiliares durante una hora cuando la unidad esta generando su maxima carga.

Energy saving in the auxiliaries consumption for circulation water pumps optimizing the thermal regime; Ahorro en el consumo de auxiliares por bombas de agua de circulacion optimando el regimen termico

Energy Technology Data Exchange (ETDEWEB)

Orozco Martinez, Roni [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1998-12-31

A methodology is proposed that should be followed in any thermal electric power plant to determine the load value at which a unit requires a second circulation water pump without affecting the thermal regime and avoiding an excessive auxiliaries consumption in partial loads. In applying this method the power plant would have an energy saving equivalent to the auxiliaries consumption during an hour, when the unit as operating at full load. [Espanol] Se propone una metodologia que debe seguirse en cualquier central termoelectrica para determinar el valor de la carga en la cual una unidad requiere de la segunda bomba de agua de circulacion sin afectar el regimen termico y evitadose un excesivo consumo de auxiliares en cargas parciales. Al aplicar este metodo la central tendria un ahorro de energia equivalente al consumo de auxiliares durante una hora cuando la unidad esta generando su maxima carga.

Importance of nuclear station load factor in applied ro energy policies

International Nuclear Information System (INIS)

Gomes, Daniel de Souza

2015-01-01

Load factor is the ration between the energy produced by a station and the energy it would have produced running at maximum power. The factor intends for all types of commercial reactors. Nuclear plants continuously provide over 11% of the world's electricity. The reactors for which data were available generated 618.7 TWh of electricity in 2014. Typical load factor was around 75% in worldwide during the first quarter of 2015. In this manner, it obtained from an average, three-monthly or yearly. The regular load factor of the reactors in operation was around 56% in 1970. While, in 1980's decade, we have an increase to 63%, the same situation occurred in next the decade and suffering increasing to 73%. Currently, the load factor reaches 78%. Accidents are seasonal factors, with the occurrence of reduction of power generation plants. In 2015 in January, there are over 437 operable commercial reactors in 31 countries, with over 377,728 MWe of full capacity. In Brazil, total capacity is 1901 MWe, with around 2.8% of electricity energy consumed. The primary objective of this study was to find a forecast model that express the evolution of the load factor in the next years. In recent years occur an extensive development of pressurized water reactors in Asia. The periodicity of seasonal effects on the performance of nuclear power plants due to aging. However, the impact of plant age depended on new technologies that allow the growth of the performance. The accident of Fukushima was an inflection point for energy policies. The event produced a trend that reduced the load in the world. (author)

Flow regimes

International Nuclear Information System (INIS)

Liles, D.R.

1982-01-01

Internal boundaries in multiphase flow greatly complicate fluid-dynamic and heat-transfer descriptions. Different flow regimes or topological configurations can have radically dissimilar interfacial and wall mass, momentum, and energy exchanges. To model the flow dynamics properly requires estimates of these rates. In this paper the common flow regimes for gas-liquid systems are defined and the techniques used to estimate the extent of a particular regime are described. Also, the current computer-code procedures are delineated and introduce a potentially better method is introduced

Benthic-planktonic coupling, regime shifts, and whole-lake primary production in shallow lakes.

Science.gov (United States)

Genkai-Kato, Motomi; Vadeboncoeur, Yvonne; Liboriussen, Lone; Jeppesen, Erik

2012-03-01

Alternative stable states in shallow lakes are typically characterized by submerged macrophyte (clear-water state) or phytoplankton (turbid state) dominance. However, a clear-water state may occur in eutrophic lakes even when macrophytes are absent. To test whether sediment algae could cause a regime shift in the absence of macrophytes, we developed a model of benthic (periphyton) and planktonic (phytoplankton) primary production using parameters derived from a shallow macrophyte-free lake that shifted from a turbid to a clear-water state following fish removal (biomanipulation). The model includes a negative feedback effect of periphyton on phosphorus (P) release from sediments. This in turn induces a positive feedback between phytoplankton production and P release. Scenarios incorporating a gradient of external P loading rates revealed that (1) periphyton and phytoplankton both contributed substantially to whole-lake production over a broad range of external P loading in a clear-water state; (2) during the clear-water state, the loss of benthic production was gradually replaced by phytoplankton production, leaving whole-lake production largely unchanged; (3) the responses of lakes to biomanipulation and increased external P loading were both dependent on lake morphometry; and (4) the capacity of periphyton to buffer the effects of increased external P loading and maintain a clear-water state was highly sensitive to relationships between light availability at the sediment surface and the of P release. Our model suggests a mechanism for the persistence of alternative states in shallow macrophyte-free lakes and demonstrates that regime shifts may trigger profound changes in ecosystem structure and function.

INFLUENCE OF REGIME SWITCHING TO RISK IN PORT-MODERN PORTFOLIO MANAGEMENT

OpenAIRE

Cristina Geambaşu; Liviu Geambaşu; Iulia Jianu

2013-01-01

The present financial crises determines an increase in analysing the application of regime switching over portfolio investments. We applied the switching regimes to measurement of risk as presented in post-modern portfolio management theory. Post-modern portfolio theory include investor’s tendency to measure risk as the chance to obtain from the investment performed a return lower than the minimum expected by him. The investor, as presented by behavioural finance, is more concerned about his ...

Distribution load estimation - DLE

Energy Technology Data Exchange (ETDEWEB)

Seppaelae, A. [VTT Energy, Espoo (Finland)

1996-12-31

The load research project has produced statistical information in the form of load models to convert the figures of annual energy consumption to hourly load values. The reliability of load models is limited to a certain network because many local circumstances are different from utility to utility and time to time. Therefore there is a need to make improvements in the load models. Distribution load estimation (DLE) is the method developed here to improve load estimates from the load models. The method is also quite cheap to apply as it utilises information that is already available in SCADA systems

Distribution load estimation - DLE

Energy Technology Data Exchange (ETDEWEB)

Seppaelae, A [VTT Energy, Espoo (Finland)

1997-12-31

The load research project has produced statistical information in the form of load models to convert the figures of annual energy consumption to hourly load values. The reliability of load models is limited to a certain network because many local circumstances are different from utility to utility and time to time. Therefore there is a need to make improvements in the load models. Distribution load estimation (DLE) is the method developed here to improve load estimates from the load models. The method is also quite cheap to apply as it utilises information that is already available in SCADA systems

Cognitive load measurement as a means to advance cognitive load theory

NARCIS (Netherlands)

Paas, F.; Tuovinen, J.E.; Tabbers, H.; van Gerven, P.W.M.

2003-01-01

This paper discusses cognitive load measurement techniques with regard to their contribution to cognitive load theory (CLT). CLT is concerned with the design of instructional methods that efficiently use people's limited cognitive processing capacity to apply acquired knowledge and skills to new

Eccentric or Concentric Exercises for the Treatment of Tendinopathies?

DEFF Research Database (Denmark)

Couppé, Christian; Svensson, René B; Silbernagel, Karin Grävare

2015-01-01

with respect to parameters like load magnitude, speed of movement, and recovery period between exercise sessions. Future studies should control for these loading parameters, evaluate various exercise dosages, and also think beyond isolated eccentric exercises to arrive at firm recommendations regarding...... exercise has been promoted. In this review we cover the relevant evidence for different exercise regimes in tendinopathy rehabilitation with particular focus on the applied loads that are experienced by the tendon and how the exercise regime may affect these applied loads. There is no convincing clinical...

Rat disc torsional mechanics: effect of lumbar and caudal levels and axial compression load.

Science.gov (United States)

Espinoza Orías, Alejandro A; Malhotra, Neil R; Elliott, Dawn M

2009-03-01

Rat models with altered loading are used to study disc degeneration and mechano-transduction. Given the prominent role of mechanics in disc function and degeneration, it is critical to measure mechanical behavior to evaluate changes after model interventions. Axial compression mechanics of the rat disc are representative of the human disc when normalized by geometry, and differences between the lumbar and caudal disc have been quantified in axial compression. No study has quantified rat disc torsional mechanics. Compare the torsional mechanical behavior of rat lumbar and caudal discs, determine the contribution of combined axial load on torsional mechanics, and compare the torsional properties of rat discs to human lumbar discs. Cadaveric biomechanical study. Cyclic torsion without compressive load followed by cyclic torsion with a fixed compressive load was applied to rat lumbar and caudal disc levels. The apparent torsional modulus was higher in the lumbar region than in the caudal region: 0.081+/-0.026 (MPa/degrees, mean+/-SD) for lumbar axially loaded; 0.066+/-0.028 for caudal axially loaded; 0.091+/-0.033 for lumbar in pure torsion; and 0.056+/-0.035 for caudal in pure torsion. These values were similar to human disc properties reported in the literature ranging from 0.024 to 0.21 MPa/degrees. Use of the caudal disc as a model may be appropriate if the mechanical focus is within the linear region of the loading regime. These results provide support for use of this animal model in basic science studies with respect to torsional mechanics.

Microprocessor control unit of thyristor regulator of microhydroelectric power station ballast load

International Nuclear Information System (INIS)

Nomokonova, Yu; Bogdanov, E

2014-01-01

The operational principle of microhydroelectric power station ballast load is presented. The comparative overview of the mathematical modeling methods is performed. The ranges of thyristors optimal work are shown as a result of the regulator regimes analysis. Shows the necessity of regulation the ballast load in microhydroelectric power station with help of developed algorithm of the program for microprocessor control

Electrical load modeling

Energy Technology Data Exchange (ETDEWEB)

Valgas, Helio Moreira; Pinto, Roberto del Giudice R.; Franca, Carlos [Companhia Energetica de Minas Gerais (CEMIG), Belo Horizonte, MG (Brazil); Lambert-Torres, Germano; Silva, Alexandre P. Alves da; Pires, Robson Celso; Costa, Junior, Roberto Affonso [Escola Federal de Engenharia de Itajuba, MG (Brazil)

1994-12-31

Accurate dynamic load models allow more precise calculations of power system controls and stability limits, which are critical mainly in the operation planning of power systems. This paper describes the development of a computer program (software) for static and dynamic load model studies using the measurement approach for the CEMIG system. Two dynamic load model structures are developed and tested. A procedure for applying a set of measured data from an on-line transient recording system to develop load models is described. (author) 6 refs., 17 figs.

Boolean logic analysis for flow regime recognition of gas–liquid horizontal flow

International Nuclear Information System (INIS)

Ramskill, Nicholas P; Wang, Mi

2011-01-01

In order to develop a flowmeter for the accurate measurement of multiphase flows, it is of the utmost importance to correctly identify the flow regime present to enable the selection of the optimal method for metering. In this study, the horizontal flow of air and water in a pipeline was studied under a multitude of conditions using electrical resistance tomography but the flow regimes that are presented in this paper have been limited to plug and bubble air–water flows. This study proposes a novel method for recognition of the prevalent flow regime using only a fraction of the data, thus rendering the analysis more efficient. By considering the average conductivity of five zones along the central axis of the tomogram, key features can be identified, thus enabling the recognition of the prevalent flow regime. Boolean logic and frequency spectrum analysis has been applied for flow regime recognition. Visualization of the flow using the reconstructed images provides a qualitative comparison between different flow regimes. Application of the Boolean logic scheme enables a quantitative comparison of the flow patterns, thus reducing the subjectivity in the identification of the prevalent flow regime

Quiescent double barrier regime in the DIII-D tokamak.

Science.gov (United States)

Greenfield, C M; Burrell, K H; DeBoo, J C; Doyle, E J; Stallard, B W; Synakowski, E J; Fenzi, C; Gohil, P; Groebner, R J; Lao, L L; Makowski, M A; McKee, G R; Moyer, R A; Rettig, C L; Rhodes, T L; Pinsker, R I; Staebler, G M; West, W P

2001-05-14

A new sustained high-performance regime, combining discrete edge and core transport barriers, has been discovered in the DIII-D tokamak. Edge localized modes (ELMs) are replaced by a steady oscillation that increases edge particle transport, thereby allowing particle control with no ELM-induced pulsed divertor heat load. The core barrier resembles those usually seen with a low (L) mode edge, without the degradation often associated with ELMs. The barriers are separated by a narrow region of high transport associated with a zero crossing in the E x B shearing rate.

Limit loads in nozzles

International Nuclear Information System (INIS)

Zouain, N.

1983-01-01

The static method for the evaluation of the limit loads of a perfectly elasto-plastic structure is presented. Using the static theorem of Limit Analysis and the Finite Element Method, a lower bound for the colapso load can be obtained through a linear programming problem. This formulation if then applied to symmetrically loaded shells of revolution and some numerical results of limit loads in nozzles are also presented. (Author) [pt

Permeability changes induced by microfissure closure and opening in tectonized materials. Effect on slope pore pressure regime.

Science.gov (United States)

De la Fuente, Maria; Vaunat, Jean; Pedone, Giuseppe; Cotecchia, Federica; Sollecito, Francesca; Casini, Francesca

2015-04-01

Tectonized clays are complex materials characterized by several levels of structures that may evolve during load and wetting/drying processes. Some microstructural patterns, as microfissures, have a particular influence on the value of permeability which is one of the main factors controlling pore pressure regime in slopes. In this work, the pore pressure regime measured in a real slope of tectonized clay in Southern Italy is analyzed by a numerical model that considers changes in permeability induced by microfissure closure and opening during the wetting and drying processes resulting from climatic actions. Permeability model accounts for the changes in Pore Size Distribution observed by Microscopy Intrusion Porosimetry. MIP tests are performed on representative samples of ground in initial conditions ("in situ" conditions) and final conditions (deformed sample after applying a wetting path that aims to reproduce the saturation of the soil under heavy rains). The resulting measurements allow for the characterization at microstructural level of the soil, identifying the distribution of dominant families pores in the sample and its evolution under external actions. Moreover, comparison of pore size density functions allows defining a microstructural parameter that depends on void ratio and degree of saturation and controls the variation of permeability. Model has been implemented in a thermo-hydro-mechanical code provided with a special boundary condition for climatic actions. Tool is used to analyze pore pressure measurements obtained in the tectonized clay slope. Results are analyzed at the light of the effect that permeability changes during wetting and drying have on the pore pressure regime.

Distribution load estimation (DLE)

Energy Technology Data Exchange (ETDEWEB)

Seppaelae, A; Lehtonen, M [VTT Energy, Espoo (Finland)

1998-08-01

The load research has produced customer class load models to convert the customers` annual energy consumption to hourly load values. The reliability of load models applied from a nation-wide sample is limited in any specific network because many local circumstances are different from utility to utility and time to time. Therefore there is a need to find improvements to the load models or, in general, improvements to the load estimates. In Distribution Load Estimation (DLE) the measurements from the network are utilized to improve the customer class load models. The results of DLE will be new load models that better correspond to the loading of the distribution network but are still close to the original load models obtained by load research. The principal data flow of DLE is presented

Codimension-two bifurcation of axial loaded beam bridge subjected to an infinite series of moving loads

International Nuclear Information System (INIS)

Yang Xin-Wei; Tian Rui-Lan; Li Hai-Tao

2013-01-01

A novel model is proposed which comprises of a beam bridge subjected to an axial load and an infinite series of moving loads. The moving loads, whose distance between the neighbouring ones is the length of the beam bridge, coupled with the axial force can lead the vibration of the beam bridge to codimension-two bifurcation. Of particular concern is a parameter regime where non-persistence set regions undergo a transition to persistence regions. The boundary of each stripe represents a bifurcation which can drive the system off a kind of dynamics and jump to another one, causing damage due to the resulting amplitude jumps. The Galerkin method, averaging method, invertible linear transformation, and near identity nonlinear transformations are used to obtain the universal unfolding for the codimension-two bifurcation of the mid-span deflection. The efficiency of the theoretical analysis obtained in this paper is verified via numerical simulations. (general)

An Applied Method for Predicting the Load-Carrying Capacity in Compression of Thin-Wall Composite Structures with Impact Damage

Science.gov (United States)

Mitrofanov, O.; Pavelko, I.; Varickis, S.; Vagele, A.

2018-03-01

The necessity for considering both strength criteria and postbuckling effects in calculating the load-carrying capacity in compression of thin-wall composite structures with impact damage is substantiated. An original applied method ensuring solution of these problems with an accuracy sufficient for practical design tasks is developed. The main advantage of the method is its applicability in terms of computing resources and the set of initial data required. The results of application of the method to solution of the problem of compression of fragments of thin-wall honeycomb panel damaged by impacts of various energies are presented. After a comparison of calculation results with experimental data, a working algorithm for calculating the reduction in the load-carrying capacity of a composite object with impact damage is adopted.

Transition from weak wave turbulence regime to solitonic regime

Science.gov (United States)

Hassani, Roumaissa; Mordant, Nicolas

2017-11-01

The Weak Turbulence Theory (WTT) is a statistical theory describing the interaction of a large ensemble of random waves characterized by very different length scales. For both weak non-linearity and weak dispersion a different regime is predicted where solitons propagate while keeping their shape unchanged. The question under investigation here is which regime between weak turbulence or soliton gas does the system choose ? We report an experimental investigation of wave turbulence at the surface of finite depth water in the gravity-capillary range. We tune the wave dispersion and the level of nonlinearity by modifying the depth of water and the forcing respectively. We use space-time resolved profilometry to reconstruct the deformed surface of water. When decreasing the water depth, we observe a drastic transition between weak turbulence at the weakest forcing and a solitonic regime at stronger forcing. We characterize the transition between both states by studying their Fourier Spectra. We also study the efficiency of energy transfer in the weak turbulence regime. We report a loss of efficiency of angular transfer as the dispersion of the wave is reduced until the system bifurcates into the solitonic regime. This project has recieved funding from the European Research Council (ERC, Grant Agreement No. 647018-WATU).

Predicting weather regime transitions in Northern Hemisphere datasets

Energy Technology Data Exchange (ETDEWEB)

Kondrashov, D. [University of California, Department of Atmospheric and Oceanic Sciences and Institute of Geophysics and Planetary Physics, Los Angeles, CA (United States); Shen, J. [UCLA, Department of Statistics, Los Angeles, CA (United States); Berk, R. [UCLA, Department of Statistics, Los Angeles, CA (United States); University of Pennsylvania, Department of Criminology, Philadelphia, PA (United States); D' Andrea, F.; Ghil, M. [Ecole Normale Superieure, Departement Terre-Atmosphere-Ocean and Laboratoire de Meteorologie Dynamique (CNRS and IPSL), Paris Cedex 05 (France)

2007-10-15

A statistical learning method called random forests is applied to the prediction of transitions between weather regimes of wintertime Northern Hemisphere (NH) atmospheric low-frequency variability. A dataset composed of 55 winters of NH 700-mb geopotential height anomalies is used in the present study. A mixture model finds that the three Gaussian components that were statistically significant in earlier work are robust; they are the Pacific-North American (PNA) regime, its approximate reverse (the reverse PNA, or RNA), and the blocked phase of the North Atlantic Oscillation (BNAO). The most significant and robust transitions in the Markov chain generated by these regimes are PNA {yields} BNAO, PNA {yields} RNA and BNAO {yields} PNA. The break of a regime and subsequent onset of another one is forecast for these three transitions. Taking the relative costs of false positives and false negatives into account, the random-forests method shows useful forecasting skill. The calculations are carried out in the phase space spanned by a few leading empirical orthogonal functions of dataset variability. Plots of estimated response functions to a given predictor confirm the crucial influence of the exit angle on a preferred transition path. This result points to the dynamic origin of the transitions. (orig.)

Methodology for local verification of flow regimes in fuel assemblies charts

International Nuclear Information System (INIS)

Igor, Sharaevsky; Elena, Sharaevskaya; Domashev, E.D.; Alexander, Arkhypov; Vladimir, Kolochko

2003-01-01

The best estimate thermal hydraulic codes describe adequately two-phase flows in nuclear energy facilities if there is proper system of closed relations. It could be obtained from the reliable information on structure forms of two-phase flows, its boundaries and reliable regime charts. In the paper the methodology of automatic recognition of the boundaries of the main types of two phase flows for rod fuel assemblies is presented. The methodology is based on definition of thermal hydraulic parameters distribution in experimental fuel assembly. The measurements were carried out using ASD signals of acoustic noise. In the paper data on two-phase flow regimes boundaries recognition especially low boundaries of bubble flow are summarized for experimental fuel assembly. The methodology of flow regimes charts applied to recognition of upper boundaries of boiling crisis regime was verificated. The satisfactory coincidence with experimental results have been shown. (author)

The Name of the Rose: Classifying 1930s Exchange-Rate Regimes

OpenAIRE

Scott Andrew Urban

2009-01-01

There is an implicit consensus that 1930s exchange-rate regimes can be characterised as some variant of ‘floating’. This paper applies an adaptation of modern methodologies of exchange-rate regime classification to a panel of 47 countries in weekly observations between January 1919 and August 1939. On the basis of modern benchmarks, the 1930s world monetary system would not be considered ‘floating’ or even ‘managed floating’. One implication is that today’s fiat-based, managed-floating intern...

FY 93 thermal loading systems study final report: Volume 1. Revision 1

International Nuclear Information System (INIS)

Saterlie, S.F.; Thomson, B.H.

1994-01-01

The ability to meet the overall performance requirements for the proposed Mined Geology Disposal System at Yucca Mountain, Nevada requires the two major subsystem (natural barriers and engineered barriers) to positively contribute to containment and radionuclide isolation. In addition to the postclosure performance the proposed repository must meet preclosure requirements of safety, retrievability, and operability. Cost and schedule were also considered. The thermal loading strategy chosen may significantly affect both the postclosure and preclosure performance of the proposed repository. Although the current Site Characterization Plan reference case is 57 kilowatts (kW)/acre, other thermal loading strategies (different areal mass loadings) have been proposed which possess both advantages and disadvantages. The objectives of the FY 1993 Thermal Loading Study were to (1) place bounds on the thermal loading which would establish the loading regime that is ''too hot'' and the loading regime that is ''too cold'', to (2) ''grade'' or evaluate the performance, as a function of thermal loading, of the repository to contain high level wastes against performance criteria and to (3) evaluate the performance of the various options with respect to cost, safety, and operability. Additionally, the effort was to (4) identify important uncertainties that need to be resolved by tests and/or analyses in order to complete a performance assessment on the effects of thermal loading. The FY 1993 Thermal Loading Study was conducted from December 1, 1992 to December 30, 1993 and this final report provides the findings of the study. Volume 1 contains the Introduction; Performance requirements; Input and assumptions; Near-field thermal analysis; Far-field thermal analysis; Cost analysis; Other considerations; System analysis; Additional thermal analysis; and Conclusions and recommendations. 71 refs., 54 figs

Crack path in aeronautical titanium alloy under ultrasonic torsion loading

Directory of Open Access Journals (Sweden)

A. Nikitin

2016-01-01

Full Text Available This paper discusses features of fatigue crack initiation and growth in aeronautical VT3-1 titanium alloy under pure torsion loading in gigacycle regime. Two materials: extruded and forged VT3-1 titanium alloys were studied. Torsion fatigue tests were performed up to fatigue life of 109 cycles. The results of the torsion tests were compared with previously obtained results under fully reversed axial loading on the same alloys. It has been shown that independently on production process as surface as well subsurface crack initiation may appear under ultrasonic torsion loading despite the maximum stress amplitude located at the specimen surface. In the case of surface crack initiation, a scenario of crack initiation and growth is similar to HCF regime except an additional possibility for internal crack branching. In the case of subsurface crack, the initiation site is located below the specimen surface (about 200 μm and is not clearly related to any material flaw. Internal crack initiation is produced by shear stress in maximum shear plane and early crack growth is in Mode II. Crack branching is limited in the case of internal crack initiation compared to surface one. A typical ‘fish-eye’ crack can be observed at the torsion fracture surface, but mechanism of crack initiation seems not to be the same than under axial fatigue loading.

Sliding friction in the hydrodynamic lubrication regime for a power-law fluid

International Nuclear Information System (INIS)

Warren, P B

2017-01-01

A scaling analysis is undertaken for the load balance in sliding friction in the hydrodynamic lubrication regime, with a particular emphasis on power-law shear-thinning typical of a structured liquid. It is argued that the shear-thinning regime is mechanically unstable if the power-law index n   <  1/2, where n is the exponent that relates the shear stress to the shear rate. Consequently the Stribeck (friction) curve should be discontinuous, with possible hysteresis. Further analysis suggests that normal stress and flow transience (stress overshoot) do not destroy this basic picture, although they may provide stabilising mechanisms at higher shear rates. Extensional viscosity is also expected to be insignificant unless the Trouton ratio is large. A possible application to shear thickening in non-Brownian particulate suspensions is indicated. (paper)

Transport processes in magnetically confined plasmas in the nonlinear regime.

Science.gov (United States)

Sonnino, Giorgio

2006-06-01

A field theory approach to transport phenomena in magnetically confined plasmas is presented. The thermodynamic field theory (TFT), previously developed for treating the generic thermodynamic system out of equilibrium, is applied to plasmas physics. Transport phenomena are treated here as the effect of the field linking the thermodynamic forces with their conjugate flows combined with statistical mechanics. In particular, the Classical and the Pfirsch-Schluter regimes are analyzed by solving the thermodynamic field equations of the TFT in the weak-field approximation. We found that, the TFT does not correct the expressions of the ionic heat fluxes evaluated by the neoclassical theory in these two regimes. On the other hand, the fluxes of matter and electronic energy (heat flow) is further enhanced in the nonlinear Classical and Pfirsch-Schluter regimes. These results seem to be in line with the experimental observations. The complete set of the electronic and ionic transport equations in the nonlinear Banana regime, is also reported. A paper showing the comparison between our theoretic results and the experimental observations in the JET machine is currently in preparation.

Lateral loadings on snubber assemblies

International Nuclear Information System (INIS)

Raphael, L.S.

1981-01-01

This paper examines the installation of snubber assemblies in power plants with respect to transverse or lateral loads as well as axial loads. Evaluation of the effects of low level, lateral loads was performed by analytical means. At higher loadings, the snubber assembly could no longer be treated as a column; therefore, the effects of lateral loadings was determined by test. The test consisted of applying both lateral and axial loads simultaneously. Results of both the analysis and the test showed that the application of lateral loads had a considerable effect on the snubber assemblies

Analysis of the Effect of Loading Process on Tribological System Properties

Directory of Open Access Journals (Sweden)

Radoslav Majdan

2016-01-01

Full Text Available The effect of loading on the properties of selected sliding pair is monitored and analysed in the submitted contribution. The obtained results of dynamic loading were also compared with static loading. The experimental tests were performed using the testing machine Tribotestor M10. Steel 11 600 was selected as a material sample for the shaft as it belongs to commonly used materials in the manufacturing of agricultural components of shaft type or pin type. A full-bronze centrifugally moulded bearing shell from the material CuSn12 was selected as the second element of friction pair. Two oils were selected for lubrication of friction node – the mineral gear oil Madit PP80 and ecological oil Plantohyd 46 S. The selected friction pairs were tested in three loading regimes according to the methodology (two dynamic processes and one static process. 60 tribological tests were performed, i.e. 10 for each type of loading and lubrication. The weight losses of the friction pair elements were part of the tracked and analysed parameters. The polluted oil was examined using the ferrographic analysis to verify the weight losses. The abrasion particles of friction pair and their contribution to oil pollution were also analysed. Following the performed experiments different effects of loading regimes may be concluded, essentially in terms of wear size and the number and size of wear particles as well. The obtained results confirmed that the power spectral density of generated signal is probably an important criterion for assessment in terms of simulated random dynamic load in given experiment. In terms of technical application in loading processes – power spectral density is actually the amount of energy supplied to the process.

Applying Cognitive Load Theory Principles to Library Instructional Guidance

Science.gov (United States)

Pickens, Kathleen E.

2017-01-01

If the goal of library instructional guidance is to provide students with the knowledge needed to acquire new skills in order to accomplish their learning objectives, then it is prudent to consider factors that impact learning. Cognitive load theory addresses several of these factors and is applicable to a wide-range of instructional devices used…

Observation of multipactor suppression in a dielectric-loaded accelerating structure using an applied axial magnetic field

International Nuclear Information System (INIS)

Jing, C.; Konecny, R.; Antipov, S.; Chang, C.; Gold, S. H.; Schoessow, P.; Kanareykin, A.; Gai, W.

2013-01-01

Efforts by a number of institutions to develop a Dielectric-Loaded Accelerating (DLA) structure capable of supporting high gradient acceleration when driven by an external radio frequency source have been ongoing over the past decade. Single surface resonant multipactor has been previously identified as one of the major limitations on the practical application of DLA structures in electron accelerators. In this paper, we report the results of an experiment that demonstrated suppression of multipactor growth in an X-band DLA structure through the use of an applied axial magnetic field. This represents an advance toward the practical use of DLA structures in many accelerator applications

Regime change?

International Nuclear Information System (INIS)

Pilat, Joseph F.; Budlong-Sylvester, K.W.

2004-01-01

Following the 1998 nuclear tests in South Asia and later reinforced by revelations about North Korean and Iraqi nuclear activities, there has been growing concern about increasing proliferation dangers. At the same time, the prospects of radiological/nuclear terrorism are seen to be rising - since 9/11, concern over a proliferation/terrorism nexus has never been higher. In the face of this growing danger, there are urgent calls for stronger measures to strengthen the current international nuclear nonproliferation regime, including recommendations to place civilian processing of weapon-useable material under multinational control. As well, there are calls for entirely new tools, including military options. As proliferation and terrorism concerns grow, the regime is under pressure and there is a temptation to consider fundamental changes to the regime. In this context, this paper will address the following: Do we need to change the regime centered on the Treaty on the Nonproliferation of Nuclear Weapons (NPT) and the International Atomic Energy Agency (IAEA)? What improvements could ensure it will be the foundation for the proliferation resistance and physical protection needed if nuclear power grows? What will make it a viable centerpiece of future nonproliferation and counterterrorism approaches?

Flow regime identification methodology with MCNP-X code and artificial neural network

International Nuclear Information System (INIS)

Salgado, Cesar M.; Instituto de Engenharia Nuclear; Schirru, Roberto; Brandao, Luis E.B.; Pereira, Claudio M.N.A.

2009-01-01

This paper presents flow regimes identification methodology in multiphase system in annular, stratified and homogeneous oil-water-gas regimes. The principle is based on recognition of the pulse height distributions (PHD) from gamma-ray with supervised artificial neural network (ANN) systems. The detection geometry simulation comprises of two NaI(Tl) detectors and a dual-energy gamma-ray source. The measurement of scattered radiation enables the dual modality densitometry (DMD) measurement principle to be explored. Its basic principle is to combine the measurement of scattered and transmitted radiation in order to acquire information about the different flow regimes. The PHDs obtained by the detectors were used as input to ANN. The data sets required for training and testing the ANN were generated by the MCNP-X code from static and ideal theoretical models of multiphase systems. The ANN correctly identified the three different flow regimes for all data set evaluated. The results presented show that PHDs examined by ANN may be applied in the successfully flow regime identification. (author)

STRAIN-STRESS DISTRIBUTION OF “HOMOGENEOUS” SOIL MASS DURING THE LOAD TRANSMITTED THROUGH THE LIMITED AREA IN THE PLAN, APPLIED INSIDE THE ELASTIC HOMOGENEOUS SOIL MASS

Directory of Open Access Journals (Sweden)

BOLSHAKOV V. I.

2017-03-01

Full Text Available Summary. Based on the current understanding of the piles work in clayey soils; that is forming during driving process a compacted core (compacted platform in the pile tip plane and transferring the load from the pile (from the piling foundation not through the pile tip but through the pressed core (compacted platform, the stress in the soil mass by the load applied inside the elastic half-space is determined with the change in the calculated scheme of load transferring to the “homogeneous” soil mass.

ANALYSING PERFORMANCE ASSESSMENT IN PUBLIC SERVICES: HOW USEFUL IS THE CONCEPT OF A PERFORMANCE REGIME?

Science.gov (United States)

Martin, Steve; Nutley, Sandra; Downe, James; Grace, Clive

2016-03-01

Approaches to performance assessment have been described as 'performance regimes', but there has been little analysis of what is meant by this concept and whether it has any real value. We draw on four perspectives on regimes - 'institutions and instruments', 'risk regulation regimes', 'internal logics and effects' and 'analytics of government' - to explore how the concept of a multi-dimensional regime can be applied to performance assessment in public services. We conclude that the concept is valuable. It helps to frame comparative and longitudinal analyses of approaches to performance assessment and draws attention to the ways in which public service performance regimes operate at different levels, how they change over time and what drives their development. Areas for future research include analysis of the impacts of performance regimes and interactions between their visible features (such as inspections, performance indicators and star ratings) and the veiled rationalities which underpin them.

Evolution and resilience of the nuclear nonproliferation regime

International Nuclear Information System (INIS)

Pregenzer, Arian L.

2014-01-01

This paper introduces the concept of systems resilience as a new framework for thinking about the future of the nonproliferation regime. Resilience refers to the ability of a system to maintain its vital functions in the face of continuous and unpredictable change. First, I make the case that the nonproliferation regime can be viewed as a complex system. Next, I discuss key themes from the literature on systems resilience and apply them to the nonproliferation system: the difference between resilience and stability; the need for evolution to maintain function; the importance of functional diversity; and the concept of the adaptive cycle. I show that most existing nonproliferation strategies are aimed at stability rather than resilience and that the current nonproliferation system may be over-constrained by the cumulative evolution of strategies. According to the literature on systems resilience, this increases its vulnerability to collapse. I argue that the resilience of the nonproliferation system can be enhanced by increasing international participation in setting the nonproliferation agenda, developing general international response capabilities, focusing on non-coercive approaches to decreasing demand, and applying systems thinking more rigorously to nonproliferation

Evolution and resilience of the nuclear nonproliferation regime

Energy Technology Data Exchange (ETDEWEB)

Pregenzer, Arian L. [Senior Scientist, Retired, Sandia National Laboratories, 13013 Arroyo de Vista NE, Albuquerque, NM 87111 (United States)

2014-05-09

This paper introduces the concept of systems resilience as a new framework for thinking about the future of the nonproliferation regime. Resilience refers to the ability of a system to maintain its vital functions in the face of continuous and unpredictable change. First, I make the case that the nonproliferation regime can be viewed as a complex system. Next, I discuss key themes from the literature on systems resilience and apply them to the nonproliferation system: the difference between resilience and stability; the need for evolution to maintain function; the importance of functional diversity; and the concept of the adaptive cycle. I show that most existing nonproliferation strategies are aimed at stability rather than resilience and that the current nonproliferation system may be over-constrained by the cumulative evolution of strategies. According to the literature on systems resilience, this increases its vulnerability to collapse. I argue that the resilience of the nonproliferation system can be enhanced by increasing international participation in setting the nonproliferation agenda, developing general international response capabilities, focusing on non-coercive approaches to decreasing demand, and applying systems thinking more rigorously to nonproliferation.

Feasibility of Applying Controllable Lubrication to Dynamically Loaded Journal Bearings

DEFF Research Database (Denmark)

Estupinan, Edgar Alberto; Santos, Ilmar

2009-01-01

A multibody dynamic model of the main mechanical components of a hermetic reciprocating compressor is presented in this work. Considering that some of the mechanical elements are interconnected via thin fluid films, the multibody dynamic model is coupled to the equations from the dynamics...... of the fluid films, based on fluid film theory. For a dynamically loaded journal bearing, the fluid film pressure distribution can be computed by numerically solving the Reynolds equation, by means of finite-difference method. Particularly, in this study the main focus is on the lubrication behavior...... and reaction forces in a reciprocating compressor have a cyclic behavior, periodic oil pressure injection rules based on the instantaneous crank angle and load bearing condition can be established. In this paper, several bearing configurations working under different oil pressure injection rules conditions...

Sufficient Stochastic Maximum Principle in a Regime-Switching Diffusion Model

Energy Technology Data Exchange (ETDEWEB)

Donnelly, Catherine, E-mail: C.Donnelly@hw.ac.uk [Heriot-Watt University, Department of Actuarial Mathematics and Statistics (United Kingdom)

2011-10-15

We prove a sufficient stochastic maximum principle for the optimal control of a regime-switching diffusion model. We show the connection to dynamic programming and we apply the result to a quadratic loss minimization problem, which can be used to solve a mean-variance portfolio selection problem.

Sufficient Stochastic Maximum Principle in a Regime-Switching Diffusion Model

International Nuclear Information System (INIS)

Donnelly, Catherine

2011-01-01

We prove a sufficient stochastic maximum principle for the optimal control of a regime-switching diffusion model. We show the connection to dynamic programming and we apply the result to a quadratic loss minimization problem, which can be used to solve a mean-variance portfolio selection problem.

Arctic circulation regimes.

Science.gov (United States)

Proshutinsky, Andrey; Dukhovskoy, Dmitry; Timmermans, Mary-Louise; Krishfield, Richard; Bamber, Jonathan L

2015-10-13

Between 1948 and 1996, mean annual environmental parameters in the Arctic experienced a well-pronounced decadal variability with two basic circulation patterns: cyclonic and anticyclonic alternating at 5 to 7 year intervals. During cyclonic regimes, low sea-level atmospheric pressure (SLP) dominated over the Arctic Ocean driving sea ice and the upper ocean counterclockwise; the Arctic atmosphere was relatively warm and humid, and freshwater flux from the Arctic Ocean towards the subarctic seas was intensified. By contrast, during anticylonic circulation regimes, high SLP dominated driving sea ice and the upper ocean clockwise. Meanwhile, the atmosphere was cold and dry and the freshwater flux from the Arctic to the subarctic seas was reduced. Since 1997, however, the Arctic system has been under the influence of an anticyclonic circulation regime (17 years) with a set of environmental parameters that are atypical for this regime. We discuss a hypothesis explaining the causes and mechanisms regulating the intensity and duration of Arctic circulation regimes, and speculate how changes in freshwater fluxes from the Arctic Ocean and Greenland impact environmental conditions and interrupt their decadal variability. © 2015 The Authors.

Causas estruturais e consequências dos regimes internacionais: regimes como variáveis intervenientes

Directory of Open Access Journals (Sweden)

Stephen D. Krasner

2012-06-01

Full Text Available Os regimes internacionais são definidos como princípios, normas, regras e procedimentos de tomada de decisões ao redor dos quais as expectativas dos atores convergem em uma dada área-tema. Como ponto de partida, os regimes são conceituados como variáveis intervenientes, estando entre fatores causais básicos e os resultados e comportamentos relacionados. Há três visões a respeito da importância dos regimes: as orientações estruturais convencionais desvalorizam os regimes como sendo, na melhor das hipóteses, ineficazes; as orientações grocianas vêem os regimes como componentes íntimos do sistema internacional; as perspectivas estruturalistas modificadas vêem os regimes como significativos somente em certas condições restritas. Para os argumentos grociano e estruturalista modificado - que concordam com a visão de que os regimes podem influenciar resultados e comportamentos - , o desenvolvimento de regimes é visto como uma função de cinco variáveis causais básicas: auto-interesse egoísta; poder político; normas e princípios difusos; usos e costumes; conhecimento.

Analysis of the Two-Regime Method on Square Meshes

KAUST Repository

Flegg, Mark B.

2014-01-01

The two-regime method (TRM) has been recently developed for optimizing stochastic reaction-diffusion simulations [M. Flegg, J. Chapman, and R. Erban, J. Roy. Soc. Interface, 9 (2012), pp. 859-868]. It is a multiscale (hybrid) algorithm which uses stochastic reaction-diffusion models with different levels of detail in different parts of the computational domain. The coupling condition on the interface between different modeling regimes of the TRM was previously derived for onedimensional models. In this paper, the TRM is generalized to higher dimensional reaction-diffusion systems. Coupling Brownian dynamics models with compartment-based models on regular (square) two-dimensional lattices is studied in detail. In this case, the interface between different modeling regimes contains either flat parts or right-angle corners. Both cases are studied in the paper. For flat interfaces, it is shown that the one-dimensional theory can be used along the line perpendicular to the TRM interface. In the direction tangential to the interface, two choices of the TRM parameters are presented. Their applicability depends on the compartment size and the time step used in the molecular-based regime. The two-dimensional generalization of the TRM is also discussed in the case of corners. © 2014 Society for Industrial and Applied Mathematics.

Modelling the drained response of bucket foundations for offshore wind turbines under general monotonic and cyclic loading

DEFF Research Database (Denmark)

Foglia, Aligi; Gottardi, Guido; Govoni, Laura

2015-01-01

The response of bucket foundations on sand subjected to planar monotonic and cyclic loading is investigated in the paper. Thirteen monotonic and cyclic laboratory tests on a skirted footing model having a 0.3 m diameter and embedment ratio equal to 1 are presented. The loading regime reproduces t...

A critique of the historical-fire-regime concept in conservation.

Science.gov (United States)

Freeman, Johanna; Kobziar, Leda; Rose, Elizabeth White; Cropper, Wendell

2017-10-01

Prescribed fire is widely accepted as a conservation tool because fire is essential to the maintenance of native biodiversity in many terrestrial communities. Approaches to this land-management technique vary greatly among continents, and sharing knowledge internationally can inform application of prescribed fire worldwide. In North America, decisions about how and when to apply prescribed fire are typically based on the historical-fire-regime concept (HFRC), which holds that replicating the pattern of fires ignited by lightning or preindustrial humans best promotes native species in fire-prone regions. The HFRC rests on 3 assumptions: it is possible to infer historical fire regimes accurately; fire-suppressed communities are ecologically degraded; and reinstating historical fire regimes is the best course of action despite the global shift toward novel abiotic and biotic conditions. We examined the underpinnings of these assumptions by conducting a literature review on the use of historical fire regimes to inform the application of prescribed fire. We found that the practice of inferring historical fire regimes for entire regions or ecosystems often entails substantial uncertainty and can yield equivocal results; ecological outcomes of fire suppression are complex and may not equate to degradation, depending on the ecosystem and context; and habitat fragmentation, invasive species, and other modern factors can interact with fire to produce novel and in some cases negative ecological outcomes. It is therefore unlikely that all 3 assumptions will be fully upheld for any landscape in which prescribed fire is being applied. Although the HFRC is a valuable starting point, it should not be viewed as the sole basis for developing prescribed fire programs. Rather, fire prescriptions should also account for other specific, measurable ecological parameters on a case-by-case basis. To best achieve conservation goals, researchers should seek to understand contemporary fire

Probabilistic Load Models for Simulating the Impact of Load Management

DEFF Research Database (Denmark)

Chen, Peiyuan; Bak-Jensen, Birgitte; Chen, Zhe

2009-01-01

. It is concluded that the AR(12) model is favored with limited measurement data and that the joint-normal model may provide better results with a large data set. Both models can be applied in general to model load time series and used in time-sequential simulation of distribution system planning.......This paper analyzes a distribution system load time series through autocorrelation coefficient, power spectral density, probabilistic distribution and quantile value. Two probabilistic load models, i.e. the joint-normal model and the autoregressive model of order 12 (AR(12)), are proposed...... to simulate the impact of load management. The joint-normal model is superior in modeling the tail region of the hourly load distribution and implementing the change of hourly standard deviation. Whereas the AR(12) model requires much less parameter and is superior in modeling the autocorrelation...

Exchange rate regimes and macroeconomic instabilities in Sub-Saharan Africa

Directory of Open Access Journals (Sweden)

Yaya Camara Seydou

2015-01-01

Full Text Available This article addresses macroeconomic instabilities according to exchange rate regimes in Sub-Saharan Africa (SSA. Based on International Monetary Fund's exchange rate regimes de facto classification, the global sample, SSA, is first divided into two subsamples, which are countries within CFA franc zone (ZCFA and those outside CFA franc zone (HZCFA, and then into four categories, which are the Western Economic and Monetary Union (WAEMU, the Central African Economic and Monetary Community, the countries CFA franc zone with fix exchange rate regimes(HZCFA-FIX, and the countries outside CFA franc zone with flexible exchange rate regimes(HZCFA-FLEX. By applying advanced statistical and econometric methods upon internal and external macroeconomic equilibrium conditions, we show that the inflation, the GDP (or the output and the real exchange rate (RER are very volatile in SSA. However, we found out that they are more volatile in the group HZCFA comparatively to the group ZCFA. We also found out that they are higher in the group HZCFA-FIX than the group HZCFA-FLEX. Moreover, we found out that a high instability of the inflation is combined with those of the output and the RER.

Nonlinear dynamic response of a 'flexible-and-heavy' printed circuit board (PCB) to an impact load applied to its support contour

International Nuclear Information System (INIS)

Suhir, E; Vujosevic, M; Reinikainen, T

2009-01-01

Based on the developed simple and physically meaningful analytical ('mathematical') stress model, we evaluate some major parameters (amplitude, frequency, maximum acceleration, stresses and strains) of the response of a 'flexible-and-heavy' square simply supported printed circuit board (PCB) to an impact drop load applied to its support contour. The analysis is restricted to the first mode of vibrations and is carried out in application to the PCB design employed in an advanced accelerated test setup (test vehicle). This setup is aimed at the assessment of the performance, in accelerated test conditions on the board level, of packaging materials (and, first of all, BGA solder joint interconnections) subjected to dynamic (drop or shock) loading. It is anticipated that heavy masses could be mounted on the PCB to accelerate its dynamic response to an impact load. These masses are expected to be small in size, so that while changing the total mass of the board and generating significant inertia forces, they do not affect the board's flexural rigidity or its stiffness with respect to the in-plane loading. The PCB's contour is considered non-deformable, which is indeed the case in many practical situations. This circumstance, if the drop height and/or the induced inertia forces are significant, leads to elevated in-plane ('membrane') stresses in the PCB and, as a result of that, to the nonlinear response of the board to the impact load: the relationship between the magnitude of the load (determined by the initial impact velocity) and the induced PCB deflections becomes geometrically nonlinear, with a rigid cubic characteristic of the restoring force. The carried out numerical example, although reflects the characteristics of the PCB and loading conditions in an actual experimental setup, is merely an illustration of the general concept and is intended to demonstrate the abilities of the suggested method. Predictions based on this method agree well with the finite element

Proposed Suitable Methods to Detect Transient Regime Switching to Improve Power Quality with Wavelet Transform

Directory of Open Access Journals (Sweden)

Javad Safaee Kuchaksaraee

2016-10-01

Full Text Available The increasing consumption of electrical energy and the use of non-linear loads that create transient regime states in distribution networks is increasing day by day. This is the only reason due to which the analysis of power quality for energy sustainability in power networks has become more important. Transients are often created by energy injection through switching or lightning and make changes in voltage and nominal current. Sudden increase or decrease in voltage or current makes characteristics of the transient regime. This paper shed some lights on the capacitor bank switching, which is one of the main causes for oscillatory transient regime states in the distribution network, using wavelet transform. The identification of the switching current of capacitor bank and the internal fault current of the transformer to prevent the unnecessary outage of the differential relay, it propose a new smart method. The accurate performance of this method is shown by simulation in EMTP and MATLAB (matrix laboratory software.

Prediction of fatigue crack growth behaviour of an α-β titanium alloy in Paris-regime using LCF properties

International Nuclear Information System (INIS)

Varma, V.K.; Saxena, V.K.; Srinivas, M.

1993-01-01

A model has been developed in the recent past to predict fatigue crack growth (FCG) behaviour in the Paris-regime of various steels by employing low cycle fatigue (LCF) properties. The model forms its basis on the assumption that the cyclic damage process immediately ahead of a crack-tip, restricted in a small zone termed as process zone, is identical to those experienced in the LCF loading of a smooth specimen. Within the process zone, fatigue damage has been assumed in terms of product of stress and plastic strain which is analogous to the plastic strain energy density of the smooth specimen under fatigue loading. In this paper the model developed by Kujawski and Ellyin has been used to predict the FCG behaviour of an α-β titanium alloy in the Paris-regime by employing the experimentally obtained LCF properties. The FCG behaviour thus theoretically predicted was compared with the experimentally determined FCG behaviour

Controllable nonlinearity in a dual-coupling optomechanical system under a weak-coupling regime

Science.gov (United States)

Zhu, Gui-Lei; Lü, Xin-You; Wan, Liang-Liang; Yin, Tai-Shuang; Bin, Qian; Wu, Ying

2018-03-01

Strong quantum nonlinearity gives rise to many interesting quantum effects and has wide applications in quantum physics. Here we investigate the quantum nonlinear effect of an optomechanical system (OMS) consisting of both linear and quadratic coupling. Interestingly, a controllable optomechanical nonlinearity is obtained by applying a driving laser into the cavity. This controllable optomechanical nonlinearity can be enhanced into a strong coupling regime, even if the system is initially in the weak-coupling regime. Moreover, the system dissipation can be suppressed effectively, which allows the appearance of phonon sideband and photon blockade effects in the weak-coupling regime. This work may inspire the exploration of a dual-coupling optomechanical system as well as its applications in modern quantum science.

Pneumatic load compensating or controlling system

Science.gov (United States)

Rogers, J. R. (Inventor)

1975-01-01

A pneumatic load compensating or controlling system for restraining a load with a predetermined force or applying a predetermined force to the load is described; it includes a source of pressurized air, a one-way pneumatic actuator operatively connected to a load, and a fluid conduit fluidically connecting the actuator with the source of pressurized air. The actuator is of the piston and cylinder type, and the end of the fluid conduit is connected to the upper or lower portion of the cylinder whereby the actuator alternatively and selectively restrains the load with a predetermined force or apply a predetermined force to the load. Pressure regulators are included within the system for variably selectively adjusting the pressurized fluid to predetermined values as desired or required; a pressure amplifier is included within the system for multiplying the pressurized values so as to achieve greater load forces. An accumulator is incorporated within the system as a failsafe operating mechanism, and visual and aural alarm devices, operatively associated with pressure detecting apparatus, readily indicate the proper or improper functioning of the system.

Applying cognitive load theory to the redesign of a conventional database systems course

Science.gov (United States)

Mason, Raina; Seton, Carolyn; Cooper, Graham

2016-01-01

Cognitive load theory (CLT) was used to redesign a Database Systems course for Information Technology students. The redesign was intended to address poor student performance and low satisfaction, and to provide a more relevant foundation in database design and use for subsequent studies and industry. The original course followed the conventional structure for a database course, covering database design first, then database development. Analysis showed the conventional course content was appropriate but the instructional materials used were too complex, especially for novice students. The redesign of instructional materials applied CLT to remove split attention and redundancy effects, to provide suitable worked examples and sub-goals, and included an extensive re-sequencing of content. The approach was primarily directed towards mid- to lower performing students and results showed a significant improvement for this cohort with the exam failure rate reducing by 34% after the redesign on identical final exams. Student satisfaction also increased and feedback from subsequent study was very positive. The application of CLT to the design of instructional materials is discussed for delivery of technical courses.

Design and commission of an experimental test rig to apply a full-scale pressure load on composite sandwich panels representative of an aircraft secondary structure

International Nuclear Information System (INIS)

Crump, D A; Dulieu-Barton, J M; Savage, J

2010-01-01

This paper describes the design of a test rig, which is used to apply a representative pressure load to a full-scale composite sandwich secondary aircraft structure. A generic panel was designed with features to represent those in the composite sandwich secondary aircraft structure. To provide full-field strain data from the panels, the test rig was designed for use with optical measurement techniques such as thermoelastic stress analysis (TSA) and digital image correlation (DIC). TSA requires a cyclic load to be applied to a structure for the measurement of the strain state; therefore, the test rig has been designed to be mounted on a standard servo-hydraulic test machine. As both TSA and DIC require an uninterrupted view of the surface of the test panel, an important consideration in the design is facilitating the optical access for the two techniques. To aid the test rig design a finite element (FE) model was produced. The model provides information on the deflections that must be accommodated by the test rig, and ensures that the stress and strain levels developed in the panel when loaded in the test rig would be sufficient for measurement using TSA and DIC. Finally, initial tests using the test rig have shown it to be capable of achieving the required pressure and maintaining a cyclic load. It was also demonstrated that both TSA and DIC data can be collected from the panels under load, which are used to validate the stress and deflection derived from the FE model

Aeroelastic tailoring for gust load alleviation

NARCIS (Netherlands)

Lancelot, P.M.G.J.; De Breuker, R.

2016-01-01

This paper presents the results from the equivalent static load method applied to gust response optimisation of an aircraft wing. Through the different optimisation runs, it is assessed that gust load cases can be critical and are difficult to constrain with the sole use of static load cases.

Dynamics of baroclinic wave pattern in transition zones between different flow regimes

International Nuclear Information System (INIS)

Larcher, Thomas von; Egbers, Christoph

2005-01-01

Baroclinic waves, both steady and time-dependent, are studied experimentally in a differentially heated rotating cylindrical gap with a free surface, cooled from within. Water is used as working fluid. We focus especially on transition zones between different flow regimes, where complex flow pattern like mixed-mode states are found. The transition from steady wave regime to irregular flow is also of particular interest. The surface flow is observed with visualisation techniques. Velocity time series are measured with the optical laser-Doppler-velocimetry technique. Thermographic measurements are applied for temperature field visualisations

Exchange rate regimes and monetary arrangements

Directory of Open Access Journals (Sweden)

Ivan Ribnikar

2005-06-01

Full Text Available There is a close relationship between a country’s exchange rate regime and monetary arrangement and if we are to examine monetary arrangements then exchange rate regimes must first be analysed. Within the conventional and most widely used classification of exchange rate regimes into rigid and flexible or into polar regimes (hard peg and float on one side, and intermediate regimes on the other there, is a much greater variety among intermediate regimes. A more precise and, as will be seen, more useful classification of exchange rate regimes is the first topic of the paper. The second topic is how exchange rate regimes influence or determine monetary arrangements and monetary policy or monetary policy regimes: monetary autonomy versus monetary nonautonomy and discretion in monetary policy versus commitment in monetary policy. Both topics are important for countries on their path to the EU and the euro area

Alumina strength degradation in the elastic regime

International Nuclear Information System (INIS)

Furnish, Michael D.; Chhabildas, Lalit C.

1998-01-01

Measurements of Kanel et al. [1991] have suggested that deviatoric stresses in glasses shocked to nearly the Hugoniot Elastic Limit (HEL) relax over a time span of microseconds after initial loading. 'Failure' (damage) waves have been inferred on the basis of these measurements using time-resolved manganin normal and transverse stress gauges. Additional experiments on glass by other researchers, using time-resolved gauges, high-speed photography and spall strength determinations have also lead to the same conclusions. In the present study we have conducted transmitted-wave experiments on high-quality Coors AD995 alumina shocked to roughly 5 and 7 GPa (just below or at the HEL). The material is subsequently reshocked to just above its elastic limit. Results of these experiments do show some evidence of strength degradation in the elastic regime

Tensile characterisation of the aorta across quasi-static to blast loading strain rates

Science.gov (United States)

Magnus, Danyal; Proud, William; Haller, Antoine; Jouffroy, Apolline

2017-06-01

The dynamic tensile failure mechanisms of the aorta during Traumatic Aortic Injury (TAI) are poorly understood. In automotive incidents, where the aorta may be under strains of the order of 100/s, TAI is the second largest cause of mortality. In these studies, the proximal descending aorta is the most common site where rupture is observed. In particular, the transverse direction is most commonly affected due to the circumferential orientation of elastin, and hence the literature generally concentrates upon axial samples. This project extends these dynamic studies to the blast loading regime where strain-rates are of the order of 1000/s. A campaign of uniaxial tensile experiments are conducted at quasi-static, intermediate (drop-weight) and high (tensile Split-Hopkinson Pressure Bar) strain rates. In each case, murine and porcine aorta models are considered and the extent of damage assessed post-loading using histology. Experimental data will be compared against current viscoelastic models of the aorta under axial stress. Their applicability across strain rates will be discussed. Using a multi-disciplinary approach, the conditions applied to the samples replicate in vivo conditions, employing a blood simulant-filled tubular specimen surrounded by a physiological solution.

About the skin effect in transient regime; Sur l'effet de peau en regime transitoire

Energy Technology Data Exchange (ETDEWEB)

Podliasky, I.

1957-06-15

Whereas always more experimental devices are using a pulsed electric supply (the electromagnetic field is applied during few microseconds only), and whereas the studied phenomenon does not last more than few microseconds, this raises the question of the behaviour in transient regime of metallic circuits or of discharge in gases. In this technical note, the author addresses the case of sufficiently high and constant gas conductivity during the studied duration. Thus, he reports a theoretical study of the establishment of a current in a high-conductivity and large-radius cylinder, and more specifically the study of the behaviour of peripheral layers (in the neighbourhood of the metal-insulator separation)

Mapping Land Management Regimes in Western Ukraine Using Optical and SAR Data

Directory of Open Access Journals (Sweden)

Jan Stefanski

2014-06-01

Full Text Available The global demand for agricultural products is surging due to population growth, more meat-based diets, and the increasing role of bioenergy. Three strategies can increase agricultural production: (1 expanding agriculture into natural ecosystems; (2 intensifying existing farmland; or (3 recultivating abandoned farmland. Because agricultural expansion entails substantial environmental trade-offs, intensification and recultivation are currently gaining increasing attention. Assessing where these strategies may be pursued, however, requires improved spatial information on land use intensity, including where farmland is active and fallow. We developed a framework to integrate optical and radar data in order to advance the mapping of three farmland management regimes: (1 large-scale, mechanized agriculture; (2 small-scale, subsistence agriculture; and (3 fallow or abandoned farmland. We applied this framework to our study area in western Ukraine, a region characterized by marked spatial heterogeneity in management intensity due to the legacies from Soviet land management, the breakdown of the Soviet Union in 1991, and the recent integration of this region into world markets. We mapped land management regimes using a hierarchical, object-based framework. Image segmentation for delineating objects was performed by using the Superpixel Contour algorithm. We then applied Random Forest classification to map land management regimes and validated our map using randomly sampled in-situ data, obtained during an extensive field campaign. Our results showed that farmland management regimes were mapped reliably, resulting in a final map with an overall accuracy of 83.4%. Comparing our land management regimes map with a soil map revealed that most fallow land occurred on soils marginally suited for agriculture, but some areas within our study region contained considerable potential for recultivation. Overall, our study highlights the potential for an improved

Low-temperature operating regime of the tokamak evacuating limiter

International Nuclear Information System (INIS)

Tokar', M.Z.

1987-01-01

The conditions for realizing the regime of strong recycling of a cold dense plasma of an evacuating limiter were determined based on a previously proposed model for describing the limiter layer of a tokamak. The scaling for the dependence of the gas pressure in the evacuation system on the average plasma density in the limiter layer was found, and agreed quantitatively with the results of measurements on the Alcator and ISX-B tokamaks. For the tokamak reactor of the INTOR scale the calculations show that the low-temperature operating regime of the evacuating limiter can be realized with a quite low pumping rate. It has the advantages of reduced erosion of the limiter and small fluxes of impurities into the working volume of the reactor. In addition, the relative concentration of the helium ash in the limiter layer does not exceed 2-3%, but the density of the main plasma is comparable to the proposed average density in the reactor. The concept of a stochastic limiter is of interest for lowering the plasma density in the limiter layer and lowering the thermal loads on the limiter

Ensuring dynamic load smoothness in problem of controlling Atomic Electric Power Stations exclusive mechanisms

International Nuclear Information System (INIS)

Shumilov, V.F.

2003-01-01

New methods for the investigation of automatic systems based on the inverse tasks of dynamics with the use of rational, trigonometric and polynomial spline functions are discussed. By means of SH function the technological regimes: start-up, steadiness, racing, braking, reverse, stop were determined. Procedure for the provision of dynamic load smoothness is suggested, and example of control over the transport systems for fuel load is considered [ru

Optimization of multi-stage dynamic treatment regimes utilizing accumulated data.

Science.gov (United States)

Huang, Xuelin; Choi, Sangbum; Wang, Lu; Thall, Peter F

2015-11-20

In medical therapies involving multiple stages, a physician's choice of a subject's treatment at each stage depends on the subject's history of previous treatments and outcomes. The sequence of decisions is known as a dynamic treatment regime or treatment policy. We consider dynamic treatment regimes in settings where each subject's final outcome can be defined as the sum of longitudinally observed values, each corresponding to a stage of the regime. Q-learning, which is a backward induction method, is used to first optimize the last stage treatment then sequentially optimize each previous stage treatment until the first stage treatment is optimized. During this process, model-based expectations of outcomes of late stages are used in the optimization of earlier stages. When the outcome models are misspecified, bias can accumulate from stage to stage and become severe, especially when the number of treatment stages is large. We demonstrate that a modification of standard Q-learning can help reduce the accumulated bias. We provide a computational algorithm, estimators, and closed-form variance formulas. Simulation studies show that the modified Q-learning method has a higher probability of identifying the optimal treatment regime even in settings with misspecified models for outcomes. It is applied to identify optimal treatment regimes in a study for advanced prostate cancer and to estimate and compare the final mean rewards of all the possible discrete two-stage treatment sequences. Copyright © 2015 John Wiley & Sons, Ltd.

Causas estruturais e consequências dos regimes internacionais: regimes como variáveis intervenientes

OpenAIRE

Krasner, Stephen D.

2012-01-01

Os regimes internacionais são definidos como princípios, normas, regras e procedimentos de tomada de decisões ao redor dos quais as expectativas dos atores convergem em uma dada área-tema. Como ponto de partida, os regimes são conceituados como variáveis intervenientes, estando entre fatores causais básicos e os resultados e comportamentos relacionados. Há três visões a respeito da importância dos regimes: as orientações estruturais convencionais desvalorizam os regimes como sendo, na melhor ...

Applying of the array transducers' technology for surface acoustic waves materials characterization in the transient regime; Application de la technologie multi-elements a la caracterisation des materiaux par ondes acoustiques de surface en regime impulsionnel

Energy Technology Data Exchange (ETDEWEB)

Frenet, D

2000-07-01

In this document we present a theoretical and experimental study which has been led to design a surface acoustic wave device for local characterisation (relatively to the wavelength) of isotropic or anisotropic materials. The device is based on a phased-array transducer of conical shape we have specifically designed for this purpose. It operates in the impulsive mode, in the frequency range of 1-5 MHz. In order to deduce mechanical properties of the material, it is possible to measure the surface wave characteristics (velocity, attenuation,...). Different methods for measuring the wave velocity have been developed taking advantage of from the phased-array technology. The originality of theses methods relies on the fact that the measures are performed without moving the transducer. Consequently, the device requires no additional mechanical system and it is quite compact. In addition, this shortens the characterisation process duration comparatively to the usually available methods (e. g. the V(z) technique). In the theoretical section of this study, a versatile model allowing to simulate in the time harmonic regime as well as in the transient regime, the transmitted field, the field reflected on isotropic or anisotropic planar samples and the output voltage for transducers of arbitrary shapes has been developed. The model has been applied to the phased-array conical transducer as well as to more classical transducers such as planar (rectangular) or focusing (spherically or cylindrically shaped) transducers. It predicts not only the geometrical contributions of the reflected field and signal but also the leaky contributions related to the surface acoustic waves. (author)

Biomechanical Modeling Analysis of Loads Configuration for Squat Exercise

Science.gov (United States)

Gallo, Christopher A.; Thompson, William K.; Lewandowski, Beth E.; Jagodnik, Kathleen; De Witt, John K.

2017-01-01

INTRODUCTION: Long duration space travel will expose astronauts to extended periods of reduced gravity. Since gravity is not present to assist loading, astronauts will use resistive and aerobic exercise regimes for the duration of the space flight to minimize loss of bone density, muscle mass and aerobic capacity that occurs during exposure to a reduced gravity environment. Unlike the International Space Station (ISS), the area available for an exercise device in the next generation of spacecraft for travel to the Moon or to Mars is limited and therefore compact resistance exercise device prototypes are being developed. The Advanced Resistive Exercise Device (ARED) currently on the ISS is being used as a benchmark for the functional performance of these new devices. Biomechanical data collection and computational modeling aid the device design process by quantifying the joint torques and the musculoskeletal forces that occur during exercises performed on the prototype devices. METHODS The computational models currently under development utilize the OpenSim [1] software platform, consisting of open source code for musculoskeletal modeling, using biomechanical input data from test subjects for estimation of muscle and joint loads. The OpenSim Full Body Model [2] is used for all analyses. The model incorporates simplified wrap surfaces, a new knee model and updated lower body muscle parameters derived from cadaver measurements and magnetic resonance imaging of young adults. The upper body uses torque actuators at the lumbar and extremity joints. The test subjects who volunteer for this study are instrumented with reflective markers for motion capture data collection while performing squat exercising on the Hybrid Ultimate Lifting Kit (HULK) prototype device (ZIN Technologies, Middleburg Heights, OH). Ground reaction force data is collected with force plates under the feet, and device loading is recorded through load cells internal to the HULK. Test variables include

Scaling electron acceleration in the bubble regime for upcoming lasers

International Nuclear Information System (INIS)

Jansen, O.; Tueckmantel, T.; Pukhov, A.

2014-01-01

Electron acceleration in the laser-plasma bubble appeared to be the most successful regime of laser wake field acceleration in the last decade. The laser technology became mature enough to generate short and relativistically intense pulses required to reach the bubble regime naturally delivering quasi-monoenergetic bunches of relativistic electrons. The upcoming laser technology projects are promising short pulses with many times more energy than the existing ones. The natural question is how will the bubble regime scale with the available laser energy. We present here a parametric study of laser-plasma acceleration in the bubble regime using full three dimensional particle-in-cell simulations and compare numerical results with the analytical scalings from the relativistic laser-plasma similarity theory. Our simulations and the theory match almost perfectly for spot sizes above R = 2λ and laser amplitudes above a 0 = 4. We also studied the emission of synchrotron radiation by the accelerated electrons. Both classical and a QED model were applied. We found borders, at which theory and simulations stopped matching. With small spot radii (R < 2λ) we almost never observed the formation of a bubble structure or any form of mono-energetic acceleration. Low laser amplitudes lead to higher energies than predicted by the theory

Sensitivity to spatial and temporal scale and fire regime inputs in deriving fire regime condition class

Science.gov (United States)

Linda Tedrow; Wendel J. Hann

2015-01-01

The Fire Regime Condition Class (FRCC) is a composite departure measure that compares current vegetation structure and fire regime to historical reference conditions. FRCC is computed as the average of: 1) Vegetation departure (VDEP) and 2) Regime (frequency and severity) departure (RDEP). In addition to the FRCC rating, the Vegetation Condition Class (VCC) and Regime...

Endoreversible quantum heat engines in the linear response regime.

Science.gov (United States)

Wang, Honghui; He, Jizhou; Wang, Jianhui

2017-07-01

We analyze general models of quantum heat engines operating a cycle of two adiabatic and two isothermal processes. We use the quantum master equation for a system to describe heat transfer current during a thermodynamic process in contact with a heat reservoir, with no use of phenomenological thermal conduction. We apply the endoreversibility description to such engine models working in the linear response regime and derive expressions of the efficiency and the power. By analyzing the entropy production rate along a single cycle, we identify the thermodynamic flux and force that a linear relation connects. From maximizing the power output, we find that such heat engines satisfy the tight-coupling condition and the efficiency at maximum power agrees with the Curzon-Ahlborn efficiency known as the upper bound in the linear response regime.

Flow Regime Identification of Co-Current Downward Two-Phase Flow With Neural Network Approach

International Nuclear Information System (INIS)

Hiroshi Goda; Seungjin Kim; Ye Mi; Finch, Joshua P.; Mamoru Ishii; Jennifer Uhle

2002-01-01

Flow regime identification for an adiabatic vertical co-current downward air-water two-phase flow in the 25.4 mm ID and the 50.8 mm ID round tubes was performed by employing an impedance void meter coupled with the neural network classification approach. This approach minimizes the subjective judgment in determining the flow regimes. The signals obtained by an impedance void meter were applied to train the self-organizing neural network to categorize these impedance signals into a certain number of groups. The characteristic parameters set into the neural network classification included the mean, standard deviation and skewness of impedance signals in the present experiment. The classification categories adopted in the present investigation were four widely accepted flow regimes, viz. bubbly, slug, churn-turbulent, and annular flows. These four flow regimes were recognized based upon the conventional flow visualization approach by a high-speed motion analyzer. The resulting flow regime maps classified by the neural network were compared with the results obtained through the flow visualization method, and consequently the efficiency of the neural network classification for flow regime identification was demonstrated. (authors)

Exploration of extremely low q_e_d_g_e regime in KSTAR

International Nuclear Information System (INIS)

Kim, Jayhyun; In, Y.; Park, B.H.; Aydemir, A.

2015-01-01

The q_e_d_g_e < 2 regime had long been regarded as an experimentally forbidden regime due to magneto-hydrodynamic instabilities. However, RFX-MOD experiment demonstrated that the control of error field could enable the entrance and sustainment of the discharge even in the forbidden regime. We explored q_e_d_g_e < 2 regime in Korea superconducting tokamak advanced research (KSTAR) without any feedback or feedforward control of error field since the intrinsic level of error field in KSTAR is inherently comparable to the controlled level of other device. The discharge sustained at q_9_5 ∼ 1.9 for 800 ms that is at least one order of magnitude longer than the resistive wall time of the device. Furthermore, simulated error field applied by field error correction coils prevented the passage of q_e_d_g_e = 3 integer rational surface before reaching q_e_d_g_e = 2. The detailed analysis is on-going for revealing the role of error field in the excitation of limiting instability. (author)

Political Economy of Exchange Rate Regimes: A Panel Data Analysis of Selected European Countries

Directory of Open Access Journals (Sweden)

Ahmet BEŞKAYA

2015-06-01

Full Text Available The aim of this study is to investigate the effects of economic and political factors on the choice of exchange rate regimes. In order to achieve this goal, we apply for Binary Choice Panel Probit Model to examine the relationships between exchange rate regimes and financial depth, real exchange rate, capital inflow and democracy. Our data covers the period of 1980-2013 for the selected EU countries, namely, Austria, Germany, Belgium, France, Denmark, England, Sweden and Italy. Estimation results demonstrates that the choice of fixed exchange rate regime become disadvantageous and flexible exchange rate turn out to be the right choice as financial depth, real exchange rate, capital inflow and democratization increases.

Linking sediment-charcoal records and ecological modeling to understand causes of fire-regime change in boreal forests

Science.gov (United States)

Linda B. Brubaker; Philip E. Higuera; T. Scott Rupp; Mark A. Olson; Patricia M. Anderson; Feng Sheng. Hu

2009-01-01

Interactions between vegetation and fire have the potential to overshadow direct effects of climate change on fire regimes in boreal forests of North America. We develop methods to compare sediment-charcoal records with fire regimes simulated by an ecological model, ALFRESCO (Alaskan Frame-based Ecosystem Code) and apply these methods to evaluate potential causes of a...

Wear analysis by applying a pin-disc configuration to phemoral head and acetabular cup

Directory of Open Access Journals (Sweden)

Guillermo Urriolagoitia-Calderón

2008-01-01

Full Text Available This work determines a prosthetic hip system’s life-span, focusing on a Mexican phenotype. The total sliding equivalent distance for the system was determined, as well as the loading regime under which the femoral component and the acetabular cup were subjected in normal operating conditions. An experimental tribology essay was then performed to simulate the wearing of the components in a Pin over Disc machine. This assay (for which the test specimens were manufactured in medical grade stainless steel AISI-ASTM 316L for the femoral component and high density polyethylene for the acetabular cup was aimed at simulating wear conditions involved in 10 years of continuous operation. A numerical simulation of operational conditions (using the finite element method was performedIn for establishing assay loading conditions to accurately determine where the loads should be applied. The tribology assay led to quantifying the volumetric loss of materials for the system being analysed. It can be concluded that the methodology proposed in this work for estimating the life-span of a prosthetic hip system was valid and accurate by comparing the results with those found in the literature. A statistical validation of the proposed method is plaaned for the future. Key words: Design life; femoral component; acetabular cup; Mexican phenotype; pin-disc configuration.

Polyethyleneimine-loaded bimodal porous silica as low-cost and high-capacity sorbent for CO{sub 2} capture

Energy Technology Data Exchange (ETDEWEB)

Witoon, Thongthai, E-mail: fengttwi@ku.ac.th [National Center of Excellence for Petroleum, Petrochemicals and Advance Material, Department of Chemical Engineering, Faculty of Engineering, Kasetsart University, Bangkok 10900 (Thailand); Center for Advanced Studies in Nanotechnology and Its Applications in Chemical Food and Agricultural Industries, Kasetsart University, Bangkok 10900 (Thailand)

2012-11-15

In this work, bimodal (meso-macro) porous silicas with different mesopore diameters synthesized by using rice husk ash as a low-cost silica source and chitosan as a natural template were used as a polyethyleneimine (PEI) support for CO{sub 2} capture. Unimodal porous silica supports with equivalent mesopore diameters to bimodal porous silica supports have been prepared for purpose of comparison. Effects of different PEI contents (10, 20, 30, 40 and 50 wt%) on CO{sub 2} sorption capacity have been systematically investigated. The porous silica supports and the PEI-loaded porous silica supports were characterized by N{sub 2}-sorption analysis, scanning electron microscopy, Fourier transform infrared spectroscopy and thermal gravimetric analysis. CO{sub 2} sorption measurements of all PEI-loaded porous silica supports were performed at different adsorption temperatures (60, 75, 85, 90, 95 and 105 Degree-Sign C). At low PEI contents (10-20 wt%), the CO{sub 2} sorption of all adsorbents was found to decrease as a function of adsorption temperature, which was a characteristic of a thermodynamically-controlled regime. A transition from the thermodynamically-controlled regime to a kinetically-controlled regime was found when the PEI content was increased up to 30 wt% for PEI-loaded unimodal porous silicas and 40 wt% for PEI-loaded bimodal porous silicas. At high PEI contents (40-50 wt%), the CO{sub 2} capturing efficiency of the PEI-loaded bimodal porous silicas was found to be considerably greater than that of the PEI-loaded unimodal porous silicas, indicating that most of the amine groups of PEI molecules loaded on the unimodal porous silica supports was useless, and thus the appeared macroporosity of the bimodal porous silica supports could provide a higher effective amine density to adsorb CO{sub 2}. Highlights: Black-Right-Pointing-Pointer PEI-impregnated bimodal porous silica as low-cost sorbent for CO{sub 2} capture. Black-Right-Pointing-Pointer Macropores enhances

Stability Estimates for a Twisted Rod Under Terminal Loads: A Three-dimensional Study

KAUST Repository

Majumdar, Apala

2012-03-01

The stability of an inextensible unshearable elastic rod with quadratic strain energy density subject to end loads is considered. We study the second variation of the corresponding rod-energy, making a distinction between in-plane and out-of-plane perturbations and isotropic and anisotropic cross-sections, respectively. In all cases, we demonstrate that the naturally straight state is a local energy minimizer in parameter regimes specified by material constants. These stability results are also accompanied by instability results in parameter regimes defined in terms of material constants. © 2012 Springer Science+Business Media B.V.

Stability Estimates for a Twisted Rod Under Terminal Loads: A Three-dimensional Study

KAUST Repository

Majumdar, Apala; Prior, Christopher; Goriely, Alain

2012-01-01

The stability of an inextensible unshearable elastic rod with quadratic strain energy density subject to end loads is considered. We study the second variation of the corresponding rod-energy, making a distinction between in-plane and out-of-plane perturbations and isotropic and anisotropic cross-sections, respectively. In all cases, we demonstrate that the naturally straight state is a local energy minimizer in parameter regimes specified by material constants. These stability results are also accompanied by instability results in parameter regimes defined in terms of material constants. © 2012 Springer Science+Business Media B.V.

Strengthening the nuclear non-proliferation regime

International Nuclear Information System (INIS)

Carlson, J.

2003-01-01

Although the nuclear non-proliferation regime has enjoyed considerable success, today the regime has never been under greater threat. Three states have challenged the objectives of the NPT, and there is a technology challenge - the spread of centrifuge enrichment technology and know-how. A major issue confronting the international community is, how to deal with a determined proliferator? Despite this gloomy scenario, however, the non-proliferation regime has considerable strengths - many of which can be developed further. The regime comprises complex interacting and mutually reinforcing elements. At its centre is the NPT - with IAEA safeguards as the Treaty's verification mechanism. Important complementary elements include: restraint in the supply and the acquisition of sensitive technologies; multilateral regimes such as the CTBT and proposed FMCT; various regional and bilateral regimes; the range of security and arms control arrangements outside the nuclear area (including other WMD regimes); and the development of proliferation-resistant technologies. Especially important are political incentives and sanctions in support of non-proliferation objectives. This paper outlines some of the key issues facing the non-proliferation regime

Autonomia e relevância dos regimes The autonomy and relevance of regimes

Directory of Open Access Journals (Sweden)

Gustavo Seignemartin de Carvalho

2005-12-01

Full Text Available Teorias institucionalistas na disciplina de relações internacionais usualmente definem regimes como um conjunto de normas e regras formais ou informais que permitem a convergência de expectativas ou a padronização do comportamento de seus participantes em uma determinada área de interesses com o objetivo de resolver problemas de coordenação que tenderiam a resultados não pareto-eficientes. Como estas definições baseadas meramente na "eficiência" dos regimes não parecem suficientes para explicar sua efetividade, o presente artigo propõe uma definição diferente para regimes: a de arranjos políticos que permitem a redistribuição dos ganhos da cooperação pelos participantes em uma determinada área de interesses em um contexto de interdependência. Regimes possuiriam efetividade pela sua autonomia e relevância, ou seja, por possuírem existência objetiva autônoma da de seus participantes e por influenciarem seu comportamento e expectativas de maneiras que não podem ser reduzidas à ação individual de nenhum deles. O artigo inicia-se com uma breve discussão sobre as dificuldades terminológicas associadas ao estudo de regimes e a definição dos conceitos de autonomia e relevância. Em seguida, classifica os diversos autores participantes do debate em duas perspectivas distintas, uma que nega (não-autonomistas e outra que atribui (autonomistas aos regimes autonomia e relevância, e faz uma breve análise dos autores e tradições mais significativos para o debate, aprofundando-se nos autonomistas e nos argumentos que reforçam a hipótese aqui apresentada. Ao final, o artigo propõe uma decomposição analítica dos regimes nos quatro elementos principais que lhes propiciam autonomia e relevância: normatividade, atores, especificidade da área de interesses e interdependência complexa com o contexto.Regimes are defined by institutionalist theories in the discipline of International Relations as formal or informal sets

Investigation of Corner Effect and Identification of Tunneling Regimes in L-Shaped Tunnel Field-Effect-Transistor.

Science.gov (United States)

Najam, Faraz; Yu, Yun Seop

2018-09-01

Corner-effect existing in L-shaped tunnel field-effect-transistor (LTFET) was investigated using numerical simulations and band diagram analysis. It was found that the corner-effect is caused by the convergence of electric field in the sharp source corner present in an LTFET, thereby increasing the electric field in the sharp source corner region. It was found that in the corner-effect region tunneling starts early, as a function of applied bias, as compared to the rest of the channel not affected by corner-effect. Further, different tunneling regimes as a function of applied bias were identified in the LTFET including source to channel and channel to channel tunneling regimes. Presence of different tunneling regimes in LTFET was analytically justified with a set of equations developed to model source to channel, and channel to channel tunneling currents. Drain-current-gate-voltage (Ids-Vgs) characteristics obtained from the equations is in reasonable qualitative agreement with numerical simulation.

Effect of Sintering Temperature and Applied Load on Anode-Supported Electrodes for SOFC Application

Directory of Open Access Journals (Sweden)

Xuan-Vien Nguyen

2016-08-01

Full Text Available Anode-supported cells are prepared by a sequence of hot pressing and co-sintering processes for solid oxide fuel cell (SOFC applications. Commercially available porous anode tape (NiO/YSZ = 50 wt %/50 wt %, anode tape (NiO/YSZ = 30 wt %/70 wt %, and YSZ are used as the anode substrate, anode functional layer, and electrolyte layer, respectively. After hot pressing, the stacked layers are then sintered at different temperatures (1250 °C, 1350 °C, 1400 °C and 1450 °C for 5 h in air. Different compressive loads are applied during the sintering process. An (La,SrMnO3 (LSM paste is coated on the post-sintered anode-supported electrolyte surface as the cathode, and sintered at different temperatures (1100 °C, 1150 °C, 1200 °C and 1250 °C for 2 h in air to generate anode-supported cells with dimensions of 60 × 60 mm2 (active reaction area of 50 × 50 mm2. SEM is used to investigate the anode structure of the anode-supported cells. In addition, confocal laser scanning microscopy is used to investigate the roughness of the cathode surfaces. At sintering temperatures of 1400 °C and 1450 °C, there is significant grain growth in the anode. Furthermore, the surface of the cathode is smoother at a firing temperature of 1200 °C. It is also found that the optimal compressive load of 1742 Pa led to a flatness of 168 µm/6 cm and a deformation of 0.72%. The open circuit voltage and power density of the anode-supported cell at 750 °C were 1.0 V and 178 mW·cm−2, respectively.

Calibration procedures for improved accuracy of wind turbine blade load measurement

Energy Technology Data Exchange (ETDEWEB)

Dahlberg, J.Aa. [Aeronautical Research Inst. of Sweden, Bromma (Sweden); Johansson, Hjalmar [Teknikgruppen AB, Sollentuna (Sweden)

1996-12-01

External loads acting on wind turbine blades are mainly transferred via the hub to the rest of the structure. It is therefore a normal approach to measure the loads acting on the turbine by load measurements in the blade roots. The load measurement is often accomplished by measurements of strain on the surface of the blade or the hub. The strain signals are converted to loads by applying calibration factors to the measurements. This paper deals with difficulties associated with load measurements on two different wind turbines; one with strain gauges applied to a steel hub where a linear stress-load relationship is expected and the other with strain gauges applied to the GFRP blade close to the bearings where strong non-linearity`s and temperature effects are expected. This paper suggests calibration methods to overcome these problems. 2 refs, 11 figs

Static converters power supply: transient regimes; Alimentation par convertisseurs statiques: regimes transitoires

Energy Technology Data Exchange (ETDEWEB)

Pasqualini, G. [Ecole Superieure d`Electricite (France)

1997-08-01

Direct current motors, asynchronous and variable speed synchronous motors are generally supplied with static converters. Speed variation is obtained by voltage variation in DC motors and by frequency variation in AC motors. In these conditions, these motors are running continuously in transient regimes: the DC motors current is not direct and the AC motors current is not sinusoidal. This situation leads to pulsing couples in the shaft line and to an increase of Joule effect losses. The aim of this paper is to present the methods of study of the electric motors functioning using the shape of the power voltages given by converters and mathematical models of these machines. The synchronous machines are rapidly described while the asynchronous machines are studied using Ku`s transformation instead of Park`s transformation for simplification. For each type of machine, calculation methods allow to determine their current, additional losses and couple characteristics. The transient regimes considered are those remaining when the motor is running at a constant speed and defined regime (supply voltages are periodical functions of time). These transient regimes are identically reproducing with a frequency which is a multiple of the converters supply frequency. Transient regimes due to functioning changes of the motor, such as resisting couple or power supply frequency variations, are not considered in this study. (J.S.) 9 refs.

Thermodynamic energy and exergy analysis of three different engine combustion regimes

International Nuclear Information System (INIS)

Li, Yaopeng; Jia, Ming; Chang, Yachao; Kokjohn, Sage L.; Reitz, Rolf D.

2016-01-01

Highlights: • Energy and exergy distributions of three different combustion regimes are studied. • CDC demonstrates the highest utilization efficiency of heat transfer and exhaust. • HCCI achieves the highest energy and exergy efficiencies over CDC and RCCI. • HCCI and RCCI demonstrate lower exergy destruction than CDC. • Combustion temperature, rate, duration and regime affect exergy destruction. - Abstract: Multi-dimensional models were coupled with a detailed chemical mechanism to investigate the energy and exergy distributions of three different combustion regimes in internal combustion engines. The results indicate that the 50% heat release point (CA50) considerably affects fuel efficiency and ringing intensity (RI), in which RI is used to quantify the knock level. Moreover, the burn duration from the 10% heat release point (CA10) to CA50 dominates RI, and the position of 90% heat release point (CA90) affects fuel efficiency. The heat transfer losses of conventional diesel combustion (CDC) strongly depend on the local temperature gradient, while it is closely related to the heat transfer area for homogeneous charge compression ignition (HCCI) and reactivity controlled compression ignition (RCCI). Among the three combustion regimes, CDC has the largest utilization efficiency for heat transfer and exhaust energy due to its higher temperature in the heat transfer layer and higher exhaust pressure and temperature. The utilization efficiency of heat transfer and exhaust in RCCI is less affected by the variation of CA50 compared to those in CDC and HCCI. Exergy destruction is closely related to the homogeneity of in-cylinder temperature and equivalence ratio during combustion process, the combustion temperature, the chemical reaction rate, and the combustion duration. Under the combined effect, HCCI and RCCI demonstrate lower exergy destruction than CDC at the same load. Overall, the variations of the exergy distribution for the three combustion regimes

Structural Load Alleviation Applied to Next Generation Aircraft and Wind Turbines

Science.gov (United States)

Frost, Susan

2011-01-01

Reducing the environmental impact of aviation is a goal of the Subsonic Fixed Wing Project under the Fundamental Aeronautics Program of NASAs Aeronautics Research Mission Directorate. Environmental impact of aviation is being addressed by novel aircraft configurations and materials that reduce aircraft weight and increase aerodynamic efficiency. NASA is developing tools to address the challenges of increased airframe flexibility created by wings constructed with reduced structural material and novel light-weight materials. This talk will present a framework and demonstration of a flight control system using optimal control allocation with structural load feedback and constraints to achieve safe aircraft operation. As wind turbines age, they become susceptible to many forms of blade degradation. Results will be presented on work in progress that uses adaptive contingency control for load mitigation in a wind turbine simulation with blade damage progression modeled.

Remote Sensing Applied to the Study of Fire Regime Attributes and Their Influence on Post-Fire Greenness Recovery in Pine Ecosystems

Directory of Open Access Journals (Sweden)

Víctor Fernández-García

2018-05-01

Full Text Available We aimed to analyze the relationship between fire regime attributes and the post-fire greenness recovery of fire-prone pine ecosystems over the short (2-year and medium (5-year term after a large wildfire, using both a single and a combined fire regime attribute approach. We characterized the spatial (fire size, temporal (number of fires, fire recurrence, and return interval, and magnitude (burn severity of the last fire fire regime attributes throughout a 40-year period with a long-time series of Landsat imagery and ancillary data. The burn severity of the last fire was measured by the dNBR (difference of the Normalized Burn Ratio spectral index, and classified according to the ground reference values of the CBI (Composite Burn Index. Post-fire greenness recovery was obtained through the difference of the NDVI (Normalized Difference Vegetation Index between pre- and post-fire Landsat scenes. The relationship between fire regime attributes (single attributes: fire recurrence, fire return interval, and burn severity; combined attributes: fire recurrence-burn severity and fire return interval-burn severity and post-fire greenness recovery was evaluated using linear models. The results indicated that all the single and combined attributes significantly affected greenness recovery. The single attribute approach showed that high recurrence, short return interval and low severity situations had the highest vegetation greenness recovery. The combined attribute approach allowed us to identify a wider variety of post-fire greenness recovery situations than the single attribute one. Over the short term, high recurrence as well as short return interval scenarios showed the best post-fire greenness recovery independently of burn severity, while over the medium term, high recurrence combined with low severity was the most recovered scenario. This novel combined attribute approach (temporal plus magnitude could be of great value to forest managers in the

Temporal variation of streamflow, sediment load and their relationship in the Yellow River basin, China.

Directory of Open Access Journals (Sweden)

Guangju Zhao

Full Text Available Variation of streamflow and sediment load in the Yellow River basin has received considerable attention due to its drastic reduction during the past several decades. This paper presents a detailed investigation on the changes of streamflow and sediment load from 1952 to 2011 using monthly observations at four gauging stations along the Yellow River. The results show significant decreasing trends for both streamflow and sediment load at all four gauging stations over the past 60 years. The wavelet transform demonstrated discontinuous periodicities from 1969 to 1973 and after 1986 due to the construction of large reservoirs and implementation of numerous soil and water conservations practices. The sediment rating curves with the power-law function was applied to investigate the relationship between discharge and sediment load. The results indicate distinct variations of the relationship between streamflow and sediment and implied significant hydro-morphological changes within different periods. The reducing sediment supply from the source region and the increased erosive power of the river are detected at Lanzhou station, while the decrease of the transport capacity at Toudaoguai is caused by severe siltation. Significant changes in the relationship between streamflow and sediment load are found at Huayuankou and Gaocun stations, which are largely induced by evident sediment income and trapping effects of large reservoirs. It is estimated that numerous reservoirs have strongly altered the regime and magnitude of streamflow and trapped large amount of sediment, leading to severe siltation and evident reduction of their total volumes. A decrease in precipitation, incoming water from the upper reaches, soil and water conservation measures as well as water consumption contribute most to the significant reduction of streamflow. The decrease of sediment load mainly resulted from various soil and water conservation measures and trapping in reservoirs

A feasibility study of low-order harmonics expansion applied to loading pattern search

Energy Technology Data Exchange (ETDEWEB)

Shaohong, Z.; Dong, L.; Tao, W. [Shanghai Jiao Tong Univ., 1954 Hua Shan Road, Shanghai, 200030 (China); Chao, Y. A. [Westinghouse Electric Company, P. O. Box 355, Pittsburgh, PA 15230-0355 (United States)

2006-07-01

Despite significant progress in core loading pattern search methods over years, there still remains the issue of large computing workload and the need for improving the speed of evaluating loading pattern candidates during the search process. This paper focuses on improving the computing speed for loading pattern evaluation, rather than the method of searching for the patterns. A low order harmonics expansion method for flux distribution representation is proposed for fast LP evaluation application. The novel feature of the method is the separation of the short range local perturbation effect from the long range global tilt effect. The latter effect can be captured by low order harmonics expansion. Demonstration examples are presented to show that even for extremely large perturbations induced by fuel shuffling the proposed method can accurately calculate the flux distribution for the LP with very minimal computation. (authors)

Hall effect in hopping regime

International Nuclear Information System (INIS)

Avdonin, A.; Skupiński, P.; Grasza, K.

2016-01-01

A simple description of the Hall effect in the hopping regime of conductivity in semiconductors is presented. Expressions for the Hall coefficient and Hall mobility are derived by considering averaged equilibrium electron transport in a single triangle of localization sites in a magnetic field. Dependence of the Hall coefficient is analyzed in a wide range of temperature and magnetic field values. Our theoretical result is applied to our experimental data on temperature dependence of Hall effect and Hall mobility in ZnO. - Highlights: • Expressions for Hall coefficient and mobility for hopping conductivity are derived. • Theoretical result is compared with experimental curves measured on ZnO. • Simultaneous action of free and hopping conduction channels is considered. • Non-linearity of hopping Hall coefficient is predicted.

Hall effect in hopping regime

Energy Technology Data Exchange (ETDEWEB)

Avdonin, A., E-mail: avdonin@ifpan.edu.pl [Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warszawa (Poland); Skupiński, P. [Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warszawa (Poland); Grasza, K. [Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warszawa (Poland); Institute of Electronic Materials Technology, ul. Wólczyńska 133, 01-919 Warszawa (Poland)

2016-02-15

A simple description of the Hall effect in the hopping regime of conductivity in semiconductors is presented. Expressions for the Hall coefficient and Hall mobility are derived by considering averaged equilibrium electron transport in a single triangle of localization sites in a magnetic field. Dependence of the Hall coefficient is analyzed in a wide range of temperature and magnetic field values. Our theoretical result is applied to our experimental data on temperature dependence of Hall effect and Hall mobility in ZnO. - Highlights: • Expressions for Hall coefficient and mobility for hopping conductivity are derived. • Theoretical result is compared with experimental curves measured on ZnO. • Simultaneous action of free and hopping conduction channels is considered. • Non-linearity of hopping Hall coefficient is predicted.

Remnants of semiclassical bistability in the few-photon regime of cavity QED.

Science.gov (United States)

Kerckhoff, Joseph; Armen, Michael A; Mabuchi, Hideo

2011-11-21

Broadband homodyne detection of the light transmitted by a Fabry-Perot cavity containing a strongly-coupled (133)Cs atom is used to probe the dynamic optical response in a regime where semiclassical theory predicts bistability but strong quantum corrections should apply. While quantum fluctuations destabilize true equilibrium bistability, our observations confirm the existence of metastable states with finite lifetimes and a hysteretic response is apparent when the optical drive is modulated on comparable timescales. Our experiment elucidates remnant semiclassical behavior in the attojoule (~10 photon) regime of single-atom cavity QED, of potential significance for ultra-low power photonic signal processing. © 2011 Optical Society of America

Assessment of functional conditions of basketball and football players during the load by applying the model of integrated evaluation.

Science.gov (United States)

Zumbakytė-Šermukšnienė, Renata; Kajėnienė, Alma; Vainoras, Alfonsas; Berškienė, Kristina; Augutienė, Viktorija

2010-01-01

We consider the human body as an adaptable, complex, and dynamic system capable of organizing itself, though there is none, the only one, factor inside the system capable of doing this job. Making use of the computerized ECG analysis system "Kaunas-load" with parallel registration of ECG carrying out body motor characteristics, ABP, or other processes characterizing hemodynamics enable one to reveal and evaluate the synergistic aspects of essential systems of the human body what particularly extends the possibilities of functional diagnostics. The aim of the study was to determine the features of alterations in the functional condition of basketball and football players and nonathletes during the bicycle ergometry test by applying the model of evaluation of the functional condition of the human body. The study population consisted of 266 healthy athletes and nonathletes. Groups of male basketball players, male football players, male nonathletes, female basketball players, and female nonathletes were studied. A computerized ECG analysis system "Kaunas-load" that is capable of both registering and analyzing the power developed by the subject and 12-lead ECG synchronically were used for evaluating the functional condition of the CVS. The subject did a computer-based bicycle ergometry test. The following ECG parameters at rest and throughout the load - HR, JT interval, and the deduced JT/RR ratio index that reflects the condition between regulatory and supplying systems - were evaluated. After measuring ABP, the pulse amplitude (S-D) was evaluated. The pulse blood pressure ratio amplitude (S-D)/S that depicts the connection between the periphery and regulatory systems was also evaluated. Speeds of changes in physiological parameters during physical load were evaluated too. Heart rate and JT/RR ratio of athletes at the rest and during load were lower, and JT interval of rest was longer and became shorter more slowly during load, compared to that of healthy nonathletes

Sustainable urban regime adjustments

DEFF Research Database (Denmark)

Quitzau, Maj-Britt; Jensen, Jens Stissing; Elle, Morten

2013-01-01

The endogenous agency that urban governments increasingly portray by making conscious and planned efforts to adjust the regimes they operate within is currently not well captured in transition studies. There is a need to acknowledge the ambiguity of regime enactment at the urban scale. This direc...

An Enhanced Drought-Tolerant Method Using SA-Loaded PAMPS Polymer Materials Applied on Tobacco Pelleted Seeds

Directory of Open Access Journals (Sweden)

Yajing Guan

2014-01-01

Full Text Available Drought is one of the most important stress factors limiting the seed industry and crop production. Present study was undertaken to create novel drought-resistant pelleted seeds using the combined materials with superabsorbent polymer, poly(2-acrylamide-2-methyl propane sulfonic acid (PAMPS hydrogel, and drought resistance agent, salicylic acid (SA. The optimized PAMPS hydrogel was obtained as the molar ratio of 2-acrylamido-2-methyl-propanesulfonic acid (AMPS to potassium peroxydisulfate (KPS and N, N′-methylene-bis-acrylamide (MBA was 1 : 0.00046 : 0.00134. The hydrogel weight after swelling in deionized water for 24 h reached 4306 times its own dry weight. The water retention ratio (RR of PAMPS was significantly higher as compared with the control. It could keep as high as 85.3% of original weight after 30 min at 110°C; even at 25°C for 40 d, the PAMPS still kept RR at 33.67%. PAMPS disintegration ratio increased gradually and reached around 30% after embedding in soil or activated sludge for 60 d. In addition, there were better seed germination performance and seedling growth in the pelleted treatments with SA-loaded PAMPS hydrogel under drought stress than control. It suggested that SA-loaded PAMPS hydrogel, a nontoxic superabsorbent polymer, could be used as an effective drought resistance material applied to tobacco pelleted seeds.

Response of monopiles under cyclic lateral loading in sand

DEFF Research Database (Denmark)

Nicolai, Giulio; Ibsen, Lars Bo

2015-01-01

Currently the main design guidelines propose to reduce the lateral resistance of offshore piles when accounting for cyclic loading. The present work provides results from laboratory tests in which such reduction has not occurred. The experimental investigation is based on testing a small......-scale monopile model in dense saturated sand. The experimental setup used to carry out the laboratory tests is able to apply thousands of load cycles and static loading to the monopile model. The purpose of the laboratory tests is to investigate the effects of cyclic loading on the lateral resistance...... of the monopile. It is shown that the soil-pile system becomes stiffer and more resistant after applying cyclic loading, depending on the number of cycles....

Bucket foundations under lateral cyclic loading

DEFF Research Database (Denmark)

Foglia, Aligi

failure envelopes. A jacked installation test is successfully compared with existing models. Tests of bucket foundations under lateral loading applied at different loading rates are analysed. As expected, the bearing capacity of bucket foundations under transient lateral loading increases dramatically...... documents on bearing capacity and installation of bucket foundations are reviewed and the results from the models found in literature are compared to the experimental results obtained in the current study. Monotonic tests of bucket foundations under lateral loading until failure are compared with existing...

Damage accumulation of bovine bone under variable amplitude loads

Directory of Open Access Journals (Sweden)

Abbey M. Campbell

2016-12-01

Full Text Available Stress fractures, a painful injury, are caused by excessive fatigue in bone. This study on damage accumulation in bone sought to determine if the Palmgren-Miner rule (PMR, a well-known linear damage accumulation hypothesis, is predictive of fatigue failure in bone. An electromagnetic shaker apparatus was constructed to conduct cyclic and variable amplitude tests on bovine bone specimens. Three distinct damage regimes were observed following fracture. Fractures due to a low cyclic amplitude loading appeared ductile (4000 μϵ, brittle due to high cyclic amplitude loading (>9000 μϵ, and a combination of ductile and brittle from mid-range cyclic amplitude loading (6500 –6750 μϵ. Brittle and ductile fracture mechanisms were isolated and mixed, in a controlled way, into variable amplitude loading tests. PMR predictions of cycles to failure consistently over-predicted fatigue life when mixing isolated fracture mechanisms. However, PMR was not proven ineffective when used with a single damage mechanism. Keywords: Bone fatigue, Bone fracture, Health system monitoring, Failure prediction

Food crises, food regimes and food movements: rumblings of reform or tides of transformation?

Science.gov (United States)

Holt Giménez, Eric; Shattuck, Annie

2011-01-01

This article addresses the potential for food movements to bring about substantive changes to the current global food system. After describing the current corporate food regime, we apply Karl Polanyi's 'double-movement' thesis on capitalism to explain the regime's trends of neoliberalism and reform. Using the global food crisis as a point of departure, we introduce a comparative analytical framework for different political and social trends within the corporate food regime and global food movements, characterizing them as 'Neoliberal', 'Reformist', 'Progressive', and 'Radical', respectively, and describe each trend based on its discourse, model, and key actors, approach to the food crisis, and key documents. After a discussion of class, political permeability, and tensions within the food movements, we suggest that the current food crisis offers opportunities for strategic alliances between Progressive and Radical trends within the food movement. We conclude that while the food crisis has brought a retrenchment of neoliberalization and weak calls for reform, the worldwide growth of food movements directly and indirectly challenge the legitimacy and hegemony of the corporate food regime. Regime change will require sustained pressure from a strong global food movement, built on durable alliances between Progressive and Radical trends.

Predicting climate-driven regime shifts versus rebound potential in coral reefs.

Science.gov (United States)

Graham, Nicholas A J; Jennings, Simon; MacNeil, M Aaron; Mouillot, David; Wilson, Shaun K

2015-02-05

Climate-induced coral bleaching is among the greatest current threats to coral reefs, causing widespread loss of live coral cover. Conditions under which reefs bounce back from bleaching events or shift from coral to algal dominance are unknown, making it difficult to predict and plan for differing reef responses under climate change. Here we document and predict long-term reef responses to a major climate-induced coral bleaching event that caused unprecedented region-wide mortality of Indo-Pacific corals. Following loss of >90% live coral cover, 12 of 21 reefs recovered towards pre-disturbance live coral states, while nine reefs underwent regime shifts to fleshy macroalgae. Functional diversity of associated reef fish communities shifted substantially following bleaching, returning towards pre-disturbance structure on recovering reefs, while becoming progressively altered on regime shifting reefs. We identified threshold values for a range of factors that accurately predicted ecosystem response to the bleaching event. Recovery was favoured when reefs were structurally complex and in deeper water, when density of juvenile corals and herbivorous fishes was relatively high and when nutrient loads were low. Whether reefs were inside no-take marine reserves had no bearing on ecosystem trajectory. Although conditions governing regime shift or recovery dynamics were diverse, pre-disturbance quantification of simple factors such as structural complexity and water depth accurately predicted ecosystem trajectories. These findings foreshadow the likely divergent but predictable outcomes for reef ecosystems in response to climate change, thus guiding improved management and adaptation.

A Coupled Model for Simulating Future Wildfire Regimes in the Western U.S.

Science.gov (United States)

Bart, R. R.; Kennedy, M. C.; Tague, C.; Hanan, E. J.

2017-12-01

Higher temperatures and larger fuel loads in the western U.S. have increased the size and intensity of wildfires over the past decades. However, it is unclear if this trend will continue over the long-term since increased wildfire activity has the countering effect of reducing landscape fuel loads, while higher temperatures alter the rate of vegetation recovery following fire. In this study, we introduce a coupled ecohydrologic-fire model for investigating how changes in vegetation, forest management, climate, and hydrology may affect future fire regimes. The spatially-distributed ecohydrologic model, RHESSys, simulates hydrologic, carbon and nutrient fluxes at watershed scales; the fire-spread model, WMFire, stochastically propagates fire on a landscape based on conditions in the ecohydrologic model. We use the coupled model to replicate fire return intervals in multiple ecoregions within the western U.S., including the southern Sierra Nevada and southern California. We also examine the sensitivity of fire return intervals to various model processes, including litter production, fire severity, and post-fire vegetation recovery rates. Results indicate that the coupled model is able to replicate expected fire return intervals in the selected locations. Fire return intervals were highly sensitive to the rate of vegetation growth, with longer fire return intervals associated with slower growing vegetation. Application of the model is expected to aid in our understanding of how fuel treatments, climate change and droughts may affect future fire regimes.

International Food Regime

Directory of Open Access Journals (Sweden)

A. V. Malov

2018-01-01

Full Text Available The review article reveals the content of the concept of Food Regime, which is little-known in the Russian academic reference. The author monitored and codified the semantic dynamic of the terminological unit from its original interpretations to modern formulations based on the retrospective analysis. The rehabilitation of the academic merits of D. Puchala and R. Hopkins — authors who used the concept Food Regime for a few years before its universally recognized origin and official scientific debut, was accomplished with help of historical and comparative methods. The author implemented the method of ascension from the abstract to the concrete to demonstrating the classification of Food Regimes compiled on the basis of geopolitical interests in the sphere of international production, consumption, and distribution of foodstuffs. The characteristic features of historically formed Food Regime were described in the chronological order, as well as modern tendencies possessing reformist potential were identified. In particular, it has been established that the idea of Food Sovereignty (which is an alternative to the modern Corporate Food Regime is the subject for acute academic disputes. The discussion between P. McMichael P. and H. Bernstein devoted to the “peasant question” — mobilization frame of the Food Sovereignty strategy was analyzed using the secondary data processing method. Due to the critical analysis, the author comes to the conclusion that it is necessary to follow the principles of the Food Sovereignty strategy to prevent the catastrophic prospects associated with ecosystem degradation, accelerated erosion of soils, the complete disappearance of biodiversity and corporate autoc racy successfully. The author is convinced that the idea of Food Sovereignty can ward off energetic liberalization of nature, intensive privatization of life and rapid monetization of unconditioned human reflexes.

Salix response to different flow regimes in controlled experiments: first results

Science.gov (United States)

Gorla, Lorenzo; Signarbieux, Constant; Buttler, Alexandre; Perona, Paolo

2013-04-01

Dams and water management for hydropower production, agriculture and other human activities alter the natural flow regime of rivers. The new river hydrograph components depend on the type of impoundment and the policy of regulation but such a different flow regime will likely affect the riparian environment. The main challenge in order to define sustainable flow releases is to quantify hydrological effects in terms of geomorphology and ecosystem response. A considerable lack of knowledge still affects the link hydrology-ecology and inadequate flow rules (e.g., minimal or residual flows) are consequently still widespread: further research in this direction is urgently required. We present an experiment, which aims to investigate the effects of different water stage regimes on riparian vegetation (salix Viminalis cuttings) development in a temperate region (Switzerland). This work describes the installation setup, together with the first results concerning the first of the two scheduled seasons of campaign. Sixty Salix cuttings were planted in non-cohesive sandy-gravel sediment within 1 meter tall plastic pots installed outside in the EPFL campus. After grouping them in three batteries, the water level within them has been varying following three river regimes simulated by adjusting the water level within the pots by means of an automatic hydraulic system. The three water level regimes reproduce a natural flow regime, a minimum residual flow policy, which only conserves peaks during flooding conditions, and an artificial regime conserving only low frequencies (e.g., seasonality) of the natural dynamic. The natural flow regime of the first battery has been applied for two months to the entire system; the three regimes above said started in June 2012. This triggered a plant response transitory regime, which we monitored by measuring plant growth, soil and atmospheric variables. Particularly, measures concern with branches development leaves photosynthesis and

Vortex rope patterns at different load of hydro turbine model

Directory of Open Access Journals (Sweden)

Skripkin Sergey

2017-01-01

Full Text Available Operation of hydraulic turbines beyond optimal conditions leads to formation of precessing vortex core in a draft tube that generates powerful pressure pulsations in a hydraulic system. In case of resonance it leads to stability decreasing of hydraulic unit and electrical grid on the whole. In present work, such regimes are explored in a conical part of simplified turbine model. Studies are performed at constant flowrate Q = 70 m3/h and varying the runner rotational speed to explore different loads of the hydroturbine unit. The experiments involve pressure measurements, high speed-visualization and velocity measurements by means of laser Doppler anemometer technique. Interesting finding is related with abrupt increasing precession frequency at low swirl parameter of flow near optimal regime.

Hoists having load support in the event of hoist failure

International Nuclear Information System (INIS)

Webb, J.

1984-01-01

A hoist having lifting means for a very heavy load also has rotatable threaded rod load supporters depending from the hoist to which the load is coupled by nuts and arms. The supporters are rotated by a slipping drive so that the nuts try to move in advance of a rise or fall of the load. The advance drive applies a raising or lowering force to the supporters which are free to move axially within small tolerances. At the limit of the tolerances brakes are applied to the rotation of the supporters. In the event of the hoist releasing the load, the load becomes supported by the arms and nuts on the supporters with the supporters firmly braked. (author)

Antecedents of Teachers Fostering Effort within Two Different Management Regimes: An Assessment-Based Accountability Regime and Regime without External Pressure on Results

Science.gov (United States)

Christophersen, Knut-Andreas; Elstad, Eyvind; Turmo, Are

2012-01-01

This article focuses on the comparison of organizational antecedents of teachers' fostering of students' effort in two quite different accountability regimes: one management regime with an external-accountability system and one with no external accountability devices. The methodology involves cross-sectional surveys from two different management…

Assessing Management Regimes in Transboundary River Basins: Do They Support Adaptive Management?

Directory of Open Access Journals (Sweden)

G.T. (Tom Raadgever

2008-06-01

Full Text Available River basin management is faced with complex problems that are characterized by uncertainty and change. In transboundary river basins, historical, legal, and cultural differences add to the complexity. The literature on adaptive management gives several suggestions for handling this complexity. It recognizes the importance of management regimes as enabling or limiting adaptive management, but there is no comprehensive overview of regime features that support adaptive management. This paper presents such an overview, focused on transboundary river basin management. It inventories the features that have been claimed to be central to effective transboundary river basin management and refines them using adaptive management literature. It then collates these features into a framework describing actor networks, policy processes, information management, and legal and financial aspects. Subsequently, this framework is applied to the Orange and Rhine basins. The paper concludes that the framework provides a consistent and comprehensive perspective on transboundary river basin management regimes, and can be used for assessing their capacity to support adaptive management.

Visões de um objeto incômodo: o regime militar brasileiro An undesirable subject: the Brazilian military regime

Directory of Open Access Journals (Sweden)

Angelo Del Vecchio

2007-05-01

Full Text Available O presente artigo visa a qualificação do regime político vigente no Brasil entre 1964-1985. Para tanto, desenvolvo o resgate do conceito de ditadura, especialmente a partir da obra de Carl Schimitt, e busco aferir a sua adequação à análise do período militar. Palavras-chave: Estado. Regime político. Ditadura. Regime militar. The present article tries to qualify the political regime in Brazil from 1964 to 1985, using the concept of dictatorship mainly developed by Carl Schimitt in his writings and tries to adequate this concept to the Brazilian military regime. Keywords: State. Political regime. Dictatorship. Military regime.

THE INFLUENCED FLOW REGIMES

Directory of Open Access Journals (Sweden)

Gavril PANDI

2011-03-01

Full Text Available The influenced flow regimes. The presence and activities ofhumanity influences the uniform environmental system, and in this context, therivers water resources. In concordance with this, the natural runoff regime suffersbigger and deeper changes. The nature of these changes depending on the type anddegree of water uses. The multitude of the use cause different types of influence,whit different quantitative aspects. In the same time, the influences havequalitative connotations, too, regarding to the modifications of the yearly watervolume runoff. So the natural runoff regime is modified. After analyzing thedistribution laws of the monthly runoff, there have been differenced four types ofinfluenced runoff regimes. In the excess type the influenced runoff is bigger thanthe natural, continuously in the whole year. The deficient type is characterized byinverse rapports like the first type, in the whole year. In the sinusoidal type, theinfluenced runoff is smaller than the natural in the period when the water isretained in the lake reservoirs, and in the depletion period the situation inverts. Atthe irregular type the ratio between influenced and natural runoff is changeable ina random meaner monthly. The recognition of the influenced regime and the gradeof influence are necessary in the evaluation and analysis of the usable hydrologicalriver resources, in the flood defence activities, in the complex scheme of thehydrographic basins, in the environment design and so on.

Global hydrological droughts in the 21st century under a changing hydrological regime

Directory of Open Access Journals (Sweden)

N. Wanders

2015-01-01

Full Text Available Climate change very likely impacts future hydrological drought characteristics across the world. Here, we quantify the impact of climate change on future low flows and associated hydrological drought characteristics on a global scale using an alternative drought identification approach that considers adaptation to future changes in hydrological regime. The global hydrological model PCR-GLOBWB was used to simulate daily discharge at 0.5° globally for 1971–2099. The model was forced with CMIP5 climate projections taken from five global circulation models (GCMs and four emission scenarios (representative concentration pathways, RCPs, from the Inter-Sectoral Impact Model Intercomparison Project. Drought events occur when discharge is below a threshold. The conventional variable threshold (VTM was calculated by deriving the threshold from the period 1971–2000. The transient variable threshold (VTMt is a non-stationary approach, where the threshold is based on the discharge values of the previous 30 years implying the threshold to vary every year during the 21st century. The VTMt adjusts to gradual changes in the hydrological regime as response to climate change. Results show a significant negative trend in the low flow regime over the 21st century for large parts of South America, southern Africa, Australia and the Mediterranean. In 40–52% of the world reduced low flows are projected, while increased low flows are found in the snow-dominated climates. In 27% of the global area both the drought duration and the deficit volume are expected to increase when applying the VTMt. However, this area will significantly increase to 62% when the VTM is applied. The mean global area in drought, with the VTMt, remains rather constant (11.7 to 13.4%, compared to the substantial increase when the VTM is applied (11.7 to 20%. The study illustrates that an alternative drought identification that considers adaptation to an altered hydrological regime has a

Flux scaling: Ultimate regime

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. Flux scaling: Ultimate regime. With the Nusselt number and the mixing length scales, we get the Nusselt number and Reynolds number (w'd/ν) scalings: and or. and. scaling expected to occur at extremely high Ra Rayleigh-Benard convection. Get the ultimate regime ...

Thermal ice loads on dams and ancillary structures: A brief review

International Nuclear Information System (INIS)

Gerard, R.

1989-01-01

A major consideration in the design of low to medium head dams in cold regions is the thrust exerted by thermal expansion of a solid ice sheet. Such loads are also of concern in the design of gates, intakes and other ancillary structures. Such loads can be greater than 300-400 kilo Newtons per meter, and are of greatest concern when ice is unshielded by snow from temperature fluctuations. Details are presented of calculation of thermal ice loads, and field measurements of thermal ice forces. Past structural failures, field and laboratory investigations, and analyses, all confirm that thermal ice loads on wide structures such as dams, and isolated structures such as bridge piers and water intakes, can be much more significant than is suggested by the loads currently specified in various North American design guidelines for hydraulic structures. While some guidelines for thermal ice loads are excessively conservative, particularly for protected situations such as gates set between piers, in other more common situations they are dangerously low. Three useful approaches that would yield information for improving thermal ice load specification are: hindcast upper bounds on thermal ice loads by assessing the ice regime and load bearing capacity of existing structures; field measurement of thermal ice loads and stresses using modern instrumentation; and measurement and analysis of the formation and movement of lake and reservoir ice covers. 23 refs., 4 figs

Transitions between corona, glow, and spark regimes of nanosecond repetitively pulsed discharges in air at atmospheric pressure

OpenAIRE

Pai , David ,; Lacoste , Deanna ,; Laux , C.

2010-01-01

International audience; In atmospheric pressure air preheated from 300 to 1000 K, the nanosecond repetitively pulsed (NRP) method has been used to generate corona, glow, and spark discharges. Experiments have been performed to determine the parameter space (applied voltage, pulse repetition frequency, ambient gas temperature, and interelectrode gap distance) of each discharge regime. In particular, the experimental conditions necessary for the glow regime of NRP discharges have been determine...

Abrupt climate-independent fire regime changes

Science.gov (United States)

Pausas, Juli G.; Keeley, Jon E.

2014-01-01

Wildfires have played a determining role in distribution, composition and structure of many ecosystems worldwide and climatic changes are widely considered to be a major driver of future fire regime changes. However, forecasting future climatic change induced impacts on fire regimes will require a clearer understanding of other drivers of abrupt fire regime changes. Here, we focus on evidence from different environmental and temporal settings of fire regimes changes that are not directly attributed to climatic changes. We review key cases of these abrupt fire regime changes at different spatial and temporal scales, including those directly driven (i) by fauna, (ii) by invasive plant species, and (iii) by socio-economic and policy changes. All these drivers might generate non-linear effects of landscape changes in fuel structure; that is, they generate fuel changes that can cross thresholds of landscape continuity, and thus drastically change fire activity. Although climatic changes might contribute to some of these changes, there are also many instances that are not primarily linked to climatic shifts. Understanding the mechanism driving fire regime changes should contribute to our ability to better assess future fire regimes.

Low cycle fatigue strength of austenitic stainless steel under large strain regime

International Nuclear Information System (INIS)

Sakai, Michiya; Saito, Kiyoshi; Matsuura, Shinichi

1998-01-01

In order to establish realistic seismic safety of nuclear power plants, it is necessary to clarify the failure mode of each components and prepare a damage evaluation method. The authors have proposed the damage evaluation method based on the fully numerical approach to evaluate the low cycle fatigue (LCF) failure under seismic loadings. This method has been validated by comparison with the dynamic failure tests of thin elbows which should be the one of the important components of the FBR primary piping system. However, since there exists limited LCF data, fatigue lives under large strain regime have been extrapolated by available fatigue data. In this study, LCF tests have been conducted over a large strain range from 2% to 10% on austenitic stainless steel SUS304. From the results, the regressive LCF curve has been proposed to modify the Wada's best-fit LCF curve under large strain regime. The usage factors calculated by author's numerical approach using proposed LCF curve have been improved to correct the underestimation of the fatigue damage. (author)

Single-source mechanical loading system produces biaxial stresses in cylinders

Science.gov (United States)

Flower, J. F.; Stafford, R. L.

1967-01-01

Single-source mechanical loading system proportions axial-to-hoop tension loads applied to cylindrical specimens. The system consists of hydraulic, pneumatic, and lever arrangements which produce biaxial loading ratios.

Superelastic load cycling of Gum Metal

International Nuclear Information System (INIS)

Vorontsov, V.A.; Jones, N.G.; Rahman, K.M.; Dye, D.

2015-01-01

The superelastic beta titanium alloy, Gum Metal, has been found to accumulate plastic strain during tensile load cycling in the superelastic regime. This is evident from the positive drift of the macroscopic stress vs. strain hysteresis curve parallel to the strain axis and the change in its geometry subsequent to every load–unload cycle. In addition, there is a progressive reduction in the hysteresis loop width and in the stress at which the superelastic transition occurs. In situ synchrotron X-ray diffraction has shown that the lattice strain exhibited the same behaviour as that observed in macroscopic measurements and identified further evidence of plastic strain accumulation. The mechanisms responsible for the observed behaviour have been evaluated using transmission electron microscopy, which revealed a range of different defects that formed during load cycling. The formation of these defects is consistent with the classical mathematical theory for the bcc to orthorhombic martensitic transformation. It is the accumulation of these defects over time that alters its superelastic behaviour

Load proportional safety brake

Science.gov (United States)

Cacciola, M. J.

1979-01-01

This brake is a self-energizing mechanical friction brake and is intended for use in a rotary drive system. It incorporates a torque sensor which cuts power to the power unit on any overload condition. The brake is capable of driving against an opposing load or driving, paying-out, an aiding load in either direction of rotation. The brake also acts as a no-back device when torque is applied to the output shaft. The advantages of using this type of device are: (1) low frictional drag when driving; (2) smooth paying-out of an aiding load with no runaway danger; (3) energy absorption proportional to load; (4) no-back activates within a few degrees of output shaft rotation and resets automatically; and (5) built-in overload protection.

Limit load assessment of centre cracked plates under biaxial loading

International Nuclear Information System (INIS)

Meek, C.; Ainsworth, R.A.

2015-01-01

Fitness-for-service of equipment and components containing defects is generally assessed using procedures such as BS 7910, API 579 and R6. There is currently little detailed advice in these procedures on the effects of biaxial and triaxial loading on fracture. This poster shows some theoretical bounding solutions of the plastic limit load for centre cracked plates under a variety of biaxial loading ratios and compares the estimates with those found by numerical methods using finite element (FE) analysis using Abacus CAE modelling software. The limit load of a structure is the maximum load that it can carry before plastic collapse occurs; this is often when the plastic zone has become large enough to spread from the crack tip to a remote boundary. For an elastic-perfectly plastic material, the irreversible deformation will continue at stresses no higher than the yield stress. The model for these limit load solutions is a bi-axially loaded plate of width 2W and height 2H, a centre crack of width 2a, acted on by remotely applied uniform stresses σ 2 perpendicular to the crack and Bσ 2 parallel to the crack, where B is the biaxial loading ratio, it means the ratio of the parallel to the perpendicular stress. A quarter plate of an elastic-perfectly plastic material has been modelled. The results show that an exact solution has been found for negative and low positive values of B. For B > 1, the lower bound solution is conservative for all values of a/W and B

On possibility of vibrational stabilization in nuclear instable stationary regimes in nuclear reactors

International Nuclear Information System (INIS)

Trakhtenberg, A.M.

1987-01-01

A principle possibility of applying the vibrational stabilization method to nuclear reactors is studied. The problem of securing the stability of nuclear reactor operation steady-state regimes is one of the central ones in dynamics theory and nuclear reaction operation experience. In particular, the problem of xenon oscillation suppressing in a reactor, occuring as a result of steady-state regime instability is urgent. Investigation is conducted using the simpliest reactor model, repesenting it as a non-linear object with concentrated parameters. It is proved that vibrational stabilization is achieved by periodic fluctuations of the control rod positions in the reactor core and boric acid concentration in the coolant with period 1s 4 s. In practice stabilization is effective, when the steady-state regime is located near the stability boundary, which appears to be dangerous, i.e. self-oscillations with inadmissibly high amplitude occure in the reactor

Static Load Distribution in Ball Bearings

Science.gov (United States)

Ricci, Mario

2010-01-01

A numerical procedure for computing the internal loading distribution in statically loaded, single-row, angular-contact ball bearings when subjected to a known combined radial and thrust load is presented. The combined radial and thrust load must be applied in order to avoid tilting between inner and outer rings. The numerical procedure requires the iterative solution of Z + 2 simultaneous nonlinear equations - where Z is the number of the balls - to yield an exact solution for axial and radial deflections, and contact angles. Numerical results for a 218 angular-contact ball bearing have been compared with those from the literature and show significant differences in the magnitudes of the ball loads, contact angles, and the extent of the loading zone.

The trade regime and the climate regime. Institutional evolution and adaptation

International Nuclear Information System (INIS)

Brewer, Thomas L.

2003-01-01

This article addresses concerns that the multilateral trade regime centered in the WTO and the emerging climate regime may conflict in ways that could be damaging to either or both. The article discusses the institutional and diplomatic context of these concerns, and it identifies the kinds of issues that are in question. The analysis suggests that there are opportunities for win-win outcomes in the interactions of the two regimes, for instance in the possibility of reducing fossil fuel subsidies. However, there are also problematic areas where they intersect. A core issue-and as yet an unresolved one-is whether and how emission credit trading and other activities envisioned by the Kyoto Protocol would be subject to WTO rules. The resolution of this issue will affect many other issues as well. Additional specific issues about the interactions of particular provisions in WTO agreements and the Kyoto Protocol are analyzed in a subsequent companion article in Climate Policy

Flow Regime Classification and Hydrological Characterization: A Case Study of Ethiopian Rivers

Directory of Open Access Journals (Sweden)

Belete Berhanu

2015-06-01

Full Text Available The spatiotemporal variability of a stream flow due to the complex interaction of catchment attributes and rainfall induce complexity in hydrology. Researchers have been trying to address this complexity with a number of approaches; river flow regime is one of them. The flow regime can be quantified by means of hydrological indices characterizing five components: magnitude, frequency, duration, timing, and rate of change of flow. Similarly, this study aimed to understand the flow variability of Ethiopian Rivers using the observed daily flow data from 208 gauging stations in the country. With this process, the Hierarchical Ward Clustering method was implemented to group the streams into three flow regimes (1 ephemeral, (2 intermittent, and (3 perennial. Principal component analysis (PCA is also applied as the second multivariate analysis tool to identify dominant hydrological indices that cause the variability in the streams. The mean flow per unit catchment area (QmAR and Base flow index (BFI show an incremental trend with ephemeral, intermittent and perennial streams. Whereas the number of mean zero flow days ratio (ZFI and coefficient of variation (CV show a decreasing trend with ephemeral to perennial flow regimes. Finally, the streams in the three flow regimes were characterized with the mean and standard deviation of the hydrological variables and the shape, slope, and scale of the flow duration curve. Results of this study are the basis for further understanding of the ecohydrological processes of the river basins in Ethiopia.

Changing Feeding Regimes To Demonstrate Flexible Biogas Production: Effects on Process Performance, Microbial Community Structure, and Methanogenesis Pathways

Science.gov (United States)

Mulat, Daniel Girma; Jacobi, H. Fabian; Feilberg, Anders; Adamsen, Anders Peter S.; Richnow, Hans-Hermann

2015-01-01

Flexible biogas production that adapts biogas output to energy demand can be regulated by changing feeding regimes. In this study, the effect of changes in feeding intervals on process performance, microbial community structure, and the methanogenesis pathway was investigated. Three different feeding regimes (once daily, every second day, and every 2 h) at the same organic loading rate were studied in continuously stirred tank reactors treating distiller's dried grains with solubles. A larger amount of biogas was produced after feeding in the reactors fed less frequently (once per day and every second day), whereas the amount remained constant in the reactor fed more frequently (every 2 h), indicating the suitability of the former for the flexible production of biogas. Compared to the conventional more frequent feeding regimes, a methane yield that was up to 14% higher and an improved stability of the process against organic overloading were achieved by employing less frequent feeding regimes. The community structures of bacteria and methanogenic archaea were monitored by terminal restriction fragment length polymorphism (T-RFLP) analysis of 16S rRNA and mcrA genes, respectively. The results showed that the composition of the bacterial community varied under the different feeding regimes, and the observed T-RFLP patterns were best explained by the differences in the total ammonia nitrogen concentrations, H2 levels, and pH values. However, the methanogenic community remained stable under all feeding regimes, with the dominance of the Methanosarcina genus followed by that of the Methanobacterium genus. Stable isotope analysis showed that the average amount of methane produced during each feeding event by acetoclastic and hydrogenotrophic methanogenesis was not influenced by the three different feeding regimes. PMID:26497462

Synergies between nonproliferation regimes: A pragmatic approach

International Nuclear Information System (INIS)

Findlay, Trevor; Meier, Oliver

2001-01-01

Full text: With the recent progress in establishing international nonproliferation regimes, the question of synergies between different verification and monitoring regimes is becoming more acute. Three multilateral and universal nonproliferation organisations covering safeguards on civil nuclear materials, nuclear testing, and chemical weapons are up and running. A regime on biological weapons is under negotiation. Several regional organisations concerned with monitoring nonproliferation commitments in the nuclear field are in place; others are being established. Past discussions on synergies between these regimes have suffered from being too far-reaching. These discussions often have not reflected adequately the political difficulties of cooperation between regimes with different membership, scope and institutional set-up. This paper takes a pragmatic look at exploiting synergies and identifies some potential and real overlaps in the work between different verification regimes. It argues for a bottom-up approach and identifies building blocks for collaboration between verification regimes. By realising such, more limited potential for cooperation, the ground could be prepared for exploiting other synergies between these regimes. (author)

De Facto Regimes in International Law

Directory of Open Access Journals (Sweden)

Jonte van Essen

2012-02-01

Full Text Available The ambiguous position of de facto regimes in international law has long been the subject of scholarly debate and a source of political conflict. An assessment of the current standing of these regimes in international law and the consequences of actions by international actors on this status has, however, been long overdue. The manner in which de facto regimes are regarded internationally has serious consequences for the individuals under the influence of this legal grey area. Therefore, the study into this problem and possible solutions is of great significance. The 2011 developments in Northern Africa underline the need of contemporary research into this area. This essay aims to clarify the position of de facto regimes in international law and the influence on their status by actions of international actors. The author first argues that de facto regimes have rights and obligations under international law, which provide them with (some form of international legal personality. He then pleads for a reconsideration of the contemporary legal treatment of these regimes. The author argues against the current system of government recognition and proposes a system that better addresses the needs of both de facto regimes and the international community. 

Full scale test SSP 34m blade, combined load. Data report

Energy Technology Data Exchange (ETDEWEB)

Nielsen, Per H.; Nielsen, Magda; Jensen, Find M. (and others)

2010-11-15

This report is part of the research project where a 34m wind turbine blade from SSP-Technology A/S was tested in combined flap and edgewise load. The applied load is 55% of an imaginary extreme event based on the certification load of the blade. This report describes the reason for choosing the loads and the load direction and the method of applying the loads to the blade. A novel load introduction allows the blade to deform in a more realistic manner, allowing the observation of e.g. transverse shear distortion. The global and local deformation of the blade as well as the blades' respond to repeated tests has been studied and the result from these investigations are presented, including the measurements performed. (Author)

Multiple growth regimes: Insights from unified growth theory

OpenAIRE

Galor, Oded

2007-01-01

Unified Growth Theory uncovers the forces that contributed to the existence of multiple growth regimes and the emergence of convergence clubs. It suggests that differential timing of take-offs from stagnation to growth segmented economies into three fundamental regimes: slow growing economies in a Malthusian regime, fast growing countries in a sustained growth regime, and economies in the transition between these regimes. In contrast to existing research that links regime switching thresholds...

Dependence of offshore wind turbine fatigue loads on atmospheric stratification

International Nuclear Information System (INIS)

Hansen, K S; Larsen, G C; Ott, S

2014-01-01

The stratification of the atmospheric boundary layer (ABL) is classified in terms of the M-O length and subsequently used to determine the relationship between ABL stability and the fatigue loads of a wind turbine located inside an offshore wind farm. Recorded equivalent fatigue loads, representing blade-bending and tower bottom bending, are combined with the operational statistics from the instrumented wind turbine as well as with meteorological statistics defining the inflow conditions. Only a part of all possible inflow conditions are covered through the approximately 8200 hours of combined measurements. The fatigue polar has been determined for an (almost) complete 360° inflow sector for both load sensors, representing mean wind speeds below and above rated wind speed, respectively, with the inflow conditions classified into three different stratification regimes: unstable, neutral and stable conditions. In general, impact of ABL stratification is clearly seen on wake affected inflow cases for both blade and tower fatigue loads. However, the character of this dependence varies significantly with the type of inflow conditions – e.g. single wake inflow or multiple wake inflow

Generating Quasi-Isentropic Loading to Targets via Flier-Plate Technique

International Nuclear Information System (INIS)

Shen Qiang; Su Xiaopeng; Wang Chuanbin; Zhang Lianmeng; Hua Jinsong; Tan Hua

2008-01-01

The quasi-isentropic loading technique allows investigation of material properties in a high-pressure, low-temperature regime that is inaccessible by conventional shock wave experiments. In the present paper, the layered flier-plate and graded density flier-plate, which have different variations in the density gradient along the thickness direction but the same density range, were designed and fabricated. Impact experiments were then performed on a two-stage light gas gun. VISAR-measured results show that wave profiles with an initial jump followed by a slowly-rising front to the peak velocity amplitude are generated by using both types of the flier-plate, indicating that quasi-isentropic loading to the targets have been successfully realized. The process of quasi-isentropic loading can be seen as the successive overlap of a series of small shock waves by the transient layers in the flier-plate. It is obvious that the graded density flier-plate creates a more smoothly rising front, and the compression effect must be closer to isentropic loading than that of the layered flier-plate with the same density range

Two different modelling methods of the saturated steam turbine load rejection

International Nuclear Information System (INIS)

Negreanu, Gabriel-Paul; Oprea, Ion

1999-01-01

One of the most difficult operation regimes of a steam turbine is the load rejection. It happens usually when the main switchgear of the unit closes unexpectedly due to some external or internal causes. In this moment, the rotor balance collapses: the motor momentum is positive, the resistant momentum is zero and the rotation velocity increases rapidly. When this process occurs, the over-speed protection should activate the emergency stop valves and the control and intercept valves in order to stop the steam admission into the turbine. The paper presents two differential approaches of the fluid dynamic processes from the flow sections of the saturated steam turbine of the NPP, where the laws of mass and energy conservation are applied. In this manner, the 'power and speed versus time' diagrams can be drawn. The main parameters of such technical problem are the closure low of the valves, the large volume of internal cavities, the huge inertial momentum of the rotor and especially the moisture of the steam that evaporates when the pressure decreases and generates an extra power in the turbine. (authors)

Frequency domain design of gain scheduling control for large wind systems in full-load region

International Nuclear Information System (INIS)

Burlibaşa, A.; Ceangă, E.

2014-01-01

Highlights: • A large wind energy system, operating under full-load regime, is considered. • According to its particularities in frequency domain, control law design is provided. • These particularities are influenced by the interactions of wind–tower–blade ensemble. • Control low, within gain scheduling strategy, is achieved imposing stability reserve. • Supplementary a criterion, aimed at reducing mechanical loads, is imposed. - Abstract: The paper presents the issue of power control law synthesis, in the case of a large wind system that operates under full-load regime, based on dynamic properties details in frequency domain. Solving this problem involves two phases: the establishment of a linearized model as faithfully as possible in various operating points of the full-load region, and synthesis of the power controller, considered with classic structure, taking into account frequency particularities of the obtained linearized model. Obtained linear model of the controlled process is of order 16 and encloses subsystems for tower fore-aft oscillations damping, and for drive-train torsion oscillations damping. The designed controller contains a PI component and a lag compensator for dynamic correction at high frequencies. It is known that the main features of wind system dynamics generated by the interaction of wind–tower–blade ensemble cause a gap in the gain characteristic of the model and complex conjugate zeros, which can move between right and left half-planes, depending on the average wind speed value. Consequently, for control law synthesis an interactive frequency solution is adopted. This is “transparent” in relation to particularities induced by wind–tower–blade interaction. This solution allows evaluation of the extent to which control law is affected by the subsystem for tower oscillations damping. Given the strong dependence between the model and the mean wind speed value, a gain scheduling control law is designed. At

A climatology of low level wind regimes over Central America using a weather type classification approach.

Directory of Open Access Journals (Sweden)

Fernán eSáenz

2015-04-01

Full Text Available Based on the potential of the weather types classification method to study synoptic features, this study proposes the application of such methodology for the identification of the main large scale patterns related with weather in Central America. Using ERA Interim low-level winds in a domain that encompasses the intra-Americas sea, the eastern tropical Pacific, southern North America, Central America and northern South America; the K-means clustering algorithm was applied to find recurrent regimes of low-level winds. Eleven regimes were identified and good coherency between the results and known features of regional circulation was found. It was determined that the main large scale patterns can be either locally forced or a response to tropical-extratropical interactions. Moreover, the local forcing dominates the summer regimes whereas mid latitude interactions lead winter regimes. The study of the relationship between the large scale patterns and regional precipitation shows that winter regimes are related with the Caribbean-Pacific precipitation seesaw. Summer regimes, on the other hand, enhance the Caribbean-Pacific precipitation contrasting distribution as a function of the dominant regimes. A strong influence of ENSO on the frequency and duration of the regimes was found. It was determined that the specific effect of ENSO on the regimes depends on whether the circulation is locally forced or lead by the interaction between the tropics and the mid-latitudes. The study of the cold surges using the information of the identified regimes revealed that three regimes are linkable with the occurrence of cold surges that affect Central America and its precipitation. As the winter regimes are largely dependent of mid-latitude interaction with the tropics, the effect that ENSO has on the Jet Stream is reflected in the winter regimes. An automated analysis of large scale conditions based on reanalysis and/or model data seems useful for both dynamical

Synthesis of polyoxometalate-loaded epoxy composites

Science.gov (United States)

Anderson, Benjamin J

2014-10-07

The synthesis of a polyoxometalate-loaded epoxy uses a one-step cure by applying an external stimulus to release the acid from the polyoxometalate and thereby catalyze the cure reaction of the epoxy resin. Such polyoxometalate-loaded epoxy composites afford the cured epoxy unique properties imparted by the intrinsic properties of the polyoxometalate. For example, polyoxometalate-loaded epoxy composites can be used as corrosion resistant epoxy coatings, for encapsulation of electronics with improved dielectric properties, and for structural applications with improved mechanical properties.

Linking meteorological drivers of spring-summer drought regimes to agricultural drought risk in China

Science.gov (United States)

Dai, L.; Wright, J. S.; Yu, C.; Huang, W. Y.

2017-12-01

As a drought prone country, China has experienced frequent severe droughts in recent decades. Drought frequency and severity are projected to increase in China under climate change. An understanding of the physical processes that contribute to extreme droughts is essential for seasonal forecasting, but the dominant physical mechanisms responsible for droughts in most parts of China are still unclear. Moreover, despite numerous studies on droughts in China, there are few clear connections between the meteorological and climatological drivers of extreme droughts and the associated agricultural consequences. This knowledge gap limits the capacity for decision-making support in drought management. The objectives of this study are (1) to identify robust spring-summer drought regimes over China, (2) to investigate the physical mechanisms associated with each regime, and (3) to better clarify connections between meteorological drought regimes and agricultural drought risk. First, we identify six drought regimes over China by applying an area-weighted k-means clustering technique to spatial patterns of spring-summer Standardized Precipitation Index (SPI) obtained from the ten-member ERA-20CM ensemble for 1900-2010. Second, we project these drought regimes onto agricultural drought risk maps for the three major cereal crops (rice, maize, and wheat) in China. Taking into account historical harvest areas for these crops, we then evaluate the potential impact of each drought regime on agricultural production. Third, the physical mechanisms and meteorological context behind each drought regimes are investigated based on monthly outputs from ERA20CM. We analyze the preceding and concurrent atmospheric circulation anomalies associated with each regime, and propose mechanistic explanations for drought development. This work provides a new perspective on diagnosing the physical mechanisms behind seasonal droughts, and lays a foundation for improving seasonal drought prediction and

Measuring the effectiveness of international environmental regimes

Energy Technology Data Exchange (ETDEWEB)

Helm, C.; Sprinz, D.F.

1999-05-01

While past research has emphasized the importance of international regimes for international governance, systematic assessments of regime effects are missing. This article derives a standardized measurement concept for the effectiveness of international environmental regimes by developing an operational rational choice calculus to evaluate actual policy simultaneously against a non-regime counterfactual and a collective optimum. Subsequently, the empirical feasibility of the measurement instrument is demonstrated by way of two international treaties regulating transboundary air pollution in Europe. The results demonstrate that the regimes indeed show positive effects - but fall substantially short of the collective optima. (orig.)

Accommodating human values in the climate regime

Directory of Open Access Journals (Sweden)

Rosalind Cook

2008-12-01

Full Text Available The climate regime addresses one of the most important challenges facing humankind today. However, while the environmental and economic sides of the problem are well represented, it lacks the inclusion of social and human aspects. The human rights regime, in contrast, is a regime which has been established precisely to implement human values. This article ex-plains the problems of climate change in terms of human values and argues that some proce-dures from the human rights regime offer possibilities for improvement. It is submitted that through the inclusion of human rights instruments, such as individual communication, pro-gressive realisation and authoritative interpretation, the inclusion of human values into the climate regime will be facilitated. This article presents these instruments and discusses their potential for inclusion in the climate regime.

Power law load dependence of atomic friction

OpenAIRE

Fusco, C.; Fasolino, A.

2004-01-01

We present a theoretical study of the dynamics of a tip scanning a graphite surface as a function of the applied load. From the analysis of the lateral forces, we extract the friction force and the corrugation of the effective tip-surface interaction potential. We find both the friction force and potential amplitude to have a power-law dependence on applied load with exponent similar to1.6. We interpret these results as characteristic of sharp undeformable tips in contrast to the case of macr...

State Structure and Political Regime Structure

Directory of Open Access Journals (Sweden)

Paul – Iulian Nedelcu

2012-05-01

Full Text Available The political regime is the concrete form of organization and functioning of political system andtherefore, the regime means the concrete way of organize, institutionalize and function a political systemand of the exercise of political power by a social-political force in a social community or global socialistem. The political regime is not limited to institutions and state bodies, but it covers the entire politicalsystem. Form of expression in social practice plan is the result of balance of forces between classes ofcitizens, organizations, between them and civil society and politics.Designates the concrete form ofgovernment formation and organization, of state bodies, in aspect of their characteristics and principles, therelations between them and other state bodies, and also as the relationship between them and otherinstitutionalized forms of political systems. Instead, the political regime is an explicit realization ofaxiological operations, a specific hierarchy of values, in general and political values, in particular. Even ifsome elements of the political regime overlap to some extent and in some respects, those of form orstructure of guvernamnt state, thus they dissolve his identity, distinct quality of being specific traits of thepolitical regime.

A Cointegrated Regime-Switching Model Approach with Jumps Applied to Natural Gas Futures Prices

Directory of Open Access Journals (Sweden)

Daniel Leonhardt

2017-09-01

Full Text Available Energy commodities and their futures naturally show cointegrated price movements. However, there is empirical evidence that the prices of futures with different maturities might have, e.g., different jump behaviours in different market situations. Observing commodity futures over time, there is also evidence for different states of the underlying volatility of the futures. In this paper, we therefore allow for cointegration of the term structure within a multi-factor model, which includes seasonality, as well as joint and individual jumps in the price processes of futures with different maturities. The seasonality in this model is realized via a deterministic function, and the jumps are represented with thinned-out compound Poisson processes. The model also includes a regime-switching approach that is modelled through a Markov chain and extends the class of geometric models. We show how the model can be calibrated to empirical data and give some practical applications.

Small-Scale Testing Rig for Long-Term Cyclically Loaded Monopiles in Cohesionless Soil

DEFF Research Database (Denmark)

Roesen, Hanne Ravn; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

2012-01-01

, and the period of the cyclic loading. However, the design guidance on these issues is limited. Thus, in order to investigate the pile behaviour for cyclically long-term loaded monopiles, a test setup for small-scale tests in saturated dense cohesionless soil is constructed and presented in here. The cyclic...... loading is applied mechanically by means of a testing rig, where the important input parameters: mean level, amplitude, number of cycles, and period of the loading can be varied. The results from a monotonic and a cyclic loading test on an open-ended aluminium pile with diameter = 100 mm and embedded...... length = 600 mm proves that the test setup is capable of applying the cyclic long-term loading. The plastic deformations during loading depend not only on the loading applied but also of the relative density of the soil and, thus, the tests are carried out with relative densities of 77-88%, i.e. similar...

Totalitäre Regimes

OpenAIRE

Merkel, Wolfgang

2004-01-01

"The development of the term and the analytical concept of totalitarianism have gone through several stages since the 1920s. However, even in its most sophisticated form, the version seen in Friedrich/ Brzezinski, the concept exhibits substantial systematic classification problems and analytical weaknesses. This article attempts to frame the type of totalitarian regime within a general typology of political regimes. Special attention is dedicated to the problem of distinguishing autocra...

Loads and loads and loads: The influence of prospective load, retrospective load, and ongoing task load in prospective memory

Directory of Open Access Journals (Sweden)

Beat eMeier

2015-06-01

Full Text Available In prospective memory tasks different kinds of load can occur. Adding a prospective memory task can impose a load on ongoing task performance. Adding ongoing task load can affect prospective memory performance. The existence of multiple target events increases prospective load and adding complexity to the to-be-remembered action increases retrospective load. In two experiments, we systematically examined the effects of these different types of load on prospective memory performance. Results showed an effect of prospective load on costs in the ongoing task for categorical targets (Experiment 2, but not for specific targets (Experiment 1. Retrospective load and ongoing task load both affected remembering the retrospective component of the prospective memory task. We suggest that prospective load can enhance costs in the ongoing task due to additional monitoring requirements. Retrospective load and ongoing task load seem to impact the division of resources between the ongoing task and retrieval of the retrospective component, which may affect disengagement from the ongoing task. In general, the results demonstrate that the different types of load affect prospective memory differentially.

Maximum allowable load on wheeled mobile manipulators

International Nuclear Information System (INIS)

Habibnejad Korayem, M.; Ghariblu, H.

2003-01-01

This paper develops a computational technique for finding the maximum allowable load of mobile manipulator during a given trajectory. The maximum allowable loads which can be achieved by a mobile manipulator during a given trajectory are limited by the number of factors; probably the dynamic properties of mobile base and mounted manipulator, their actuator limitations and additional constraints applied to resolving the redundancy are the most important factors. To resolve extra D.O.F introduced by the base mobility, additional constraint functions are proposed directly in the task space of mobile manipulator. Finally, in two numerical examples involving a two-link planar manipulator mounted on a differentially driven mobile base, application of the method to determining maximum allowable load is verified. The simulation results demonstrates the maximum allowable load on a desired trajectory has not a unique value and directly depends on the additional constraint functions which applies to resolve the motion redundancy

'CANDLE' burnup regime after LWR regime

International Nuclear Information System (INIS)

Sekimoto, Hiroshi; Nagata, Akito

2008-01-01

CANDLE (Constant Axial shape of Neutron flux, nuclide densities and power shape During Life of Energy producing reactor) burnup strategy can derive many merits. From safety point of view, the change of excess reactivity along burnup is theoretically zero, and the core characteristics, such as power feedback coefficients and power peaking factor, are not changed along burnup. Application of this burnup strategy to neutron rich fast reactors makes excellent performances. Only natural or depleted uranium is required for the replacing fuels. About 40% of natural or depleted uranium undergoes fission without the conventional reprocessing and enrichment. If the LWR produced energy of X Joules, the CANDLE reactor can produce about 50X Joules from the depleted uranium left at the enrichment facility for the LWR fuel. If we can say LWRs have produced energy sufficient for full 20 years, we can produce the energy for 1000 years by using the CANDLE reactors with depleted uranium. We need not mine any uranium ore, and do not need reprocessing facility. The burnup of spent fuel becomes 10 times. Therefore, the spent fuel amount per produced energy is also reduced to one-tenth. The details of the scenario of CANDLE burnup regime after LWR regime will be presented at the symposium. (author)

Changing Feeding Regimes To Demonstrate Flexible Biogas Production: Effects on Process Performance, Microbial Community Structure, and Methanogenesis Pathways.

Science.gov (United States)

Mulat, Daniel Girma; Jacobi, H Fabian; Feilberg, Anders; Adamsen, Anders Peter S; Richnow, Hans-Hermann; Nikolausz, Marcell

2016-01-15

Flexible biogas production that adapts biogas output to energy demand can be regulated by changing feeding regimes. In this study, the effect of changes in feeding intervals on process performance, microbial community structure, and the methanogenesis pathway was investigated. Three different feeding regimes (once daily, every second day, and every 2 h) at the same organic loading rate were studied in continuously stirred tank reactors treating distiller's dried grains with solubles. A larger amount of biogas was produced after feeding in the reactors fed less frequently (once per day and every second day), whereas the amount remained constant in the reactor fed more frequently (every 2 h), indicating the suitability of the former for the flexible production of biogas. Compared to the conventional more frequent feeding regimes, a methane yield that was up to 14% higher and an improved stability of the process against organic overloading were achieved by employing less frequent feeding regimes. The community structures of bacteria and methanogenic archaea were monitored by terminal restriction fragment length polymorphism (T-RFLP) analysis of 16S rRNA and mcrA genes, respectively. The results showed that the composition of the bacterial community varied under the different feeding regimes, and the observed T-RFLP patterns were best explained by the differences in the total ammonia nitrogen concentrations, H2 levels, and pH values. However, the methanogenic community remained stable under all feeding regimes, with the dominance of the Methanosarcina genus followed by that of the Methanobacterium genus. Stable isotope analysis showed that the average amount of methane produced during each feeding event by acetoclastic and hydrogenotrophic methanogenesis was not influenced by the three different feeding regimes. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

IDENTIFICATION OF WIND LOAD APPLIED TO THREE-DIMENSIONAL STRUCTURES BY VIRTUE OF ITS SIMULATION IN THE WIND TUNNEL

Directory of Open Access Journals (Sweden)

Doroshenko Sergey Aleksandrovich

2012-10-01

Full Text Available The authors discuss wind loads applied to a set of two buildings. The wind load is simulated with the help of the wind tunnel. In the Russian Federation, special attention is driven to the aerodynamics of high-rise buildings and structures. According to the Russian norms, identification of aerodynamic coefficients for high-rise buildings, as well as the influence of adjacent buildings and structures, is performed on the basis of models of structures exposed to wind impacts simulated in the wind tunnel. This article deals with the results of the wind tunnel test of buildings. The simulation was carried out with the involvement of a model of two twenty-three storied buildings. The experiment was held in a wind tunnel of the closed type at in the Institute of Mechanics of Moscow State University. Data were compared at the zero speed before and after the experiment. LabView software was used to process the output data. Graphs and tables were developed in the Microsoft Excel package. GoogleSketchUp software was used as a visualization tool. The three-dimensional flow formed in the wind tunnel can't be adequately described by solving the two-dimensional problem. The aerodynamic experiment technique is used to analyze the results for eighteen angles of the wind attack.

Algorithm for Non-proportional Loading in Sequentially Linear Analysis

NARCIS (Netherlands)

Yu, C.; Hoogenboom, P.C.J.; Rots, J.G.; Saouma, V.; Bolander, J.; Landis, E.

2016-01-01

Sequentially linear analysis (SLA) is an alternative to the Newton-Raphson method for analyzing the nonlinear behavior of reinforced concrete and masonry structures. In this paper SLA is extended to load cases that are applied one after the other, for example first dead load and then wind load. It

Physics Based Model for Online Fault Detection in Autonomous Cryogenic Loading System

Science.gov (United States)

Kashani, Ali; Devine, Ekaterina Viktorovna P; Luchinsky, Dmitry Georgievich; Smelyanskiy, Vadim; Sass, Jared P.; Brown, Barbara L.; Patterson-Hine, Ann

2013-01-01

We report the progress in the development of the chilldown model for rapid cryogenic loading system developed at KSC. The nontrivial characteristic feature of the analyzed chilldown regime is its active control by dump valves. The two-phase flow model of the chilldown is approximated as one-dimensional homogeneous fluid flow with no slip condition for the interphase velocity. The model is built using commercial SINDAFLUINT software. The results of numerical predictions are in good agreement with the experimental time traces. The obtained results pave the way to the application of the SINDAFLUINT model as a verification tool for the design and algorithm development required for autonomous loading operation.

Power load limits of the WENDELSTEIN 7-X target elements-comparison of experimental results and design values for power loads up to the critical heat flux

International Nuclear Information System (INIS)

Greuner, H; Boeswirth, B; Boscary, J; Leuprecht, A; Plankensteiner, A

2007-01-01

The power load limits of the WENDELSTEIN7-X divertor target elements were experimentally evaluated with heat loads considerably exceeding the expected operating conditions. The water-cooled elements are designed for steady-state heat flux of 10 MW m -2 and to remove a power load up to 100 kW. The elements must allow a limited operation time at 12 MW m -2 steady-state and should not fail for short pulses of up to 15 MW m -2 for cooling conditions in the subcooled nucleate boiling regime. In the framework of the qualification phase, pre-series target elements were loaded up to 24 MW m -2 without loss of CFC tiles. A critical heat flux at the target of 31 MW m -2 was achieved. The paper discusses the results of the tests performed at the high heat flux test facility GLADIS. The experimental results compared to transient nonlinear fine element method (FEM) calculations confirm a high thermal safety margin of the target design sufficient for plasma operation in W7-X

Modal and Wave Load Identification by ARMA Calibration

DEFF Research Database (Denmark)

Jensen, Jens Kristian Jehrbo; Kirkegaard, Poul Henning; Brincker, Rune

1992-01-01

In this note, modal parameter and wave load identification by calibration of ARMA models are considered for a simple offshore structure. The theory of identification by ARMA calibration is introduced as an identification technique in the time domain, which can be applied for white noise–excited s......In this note, modal parameter and wave load identification by calibration of ARMA models are considered for a simple offshore structure. The theory of identification by ARMA calibration is introduced as an identification technique in the time domain, which can be applied for white noise...... by an experimental example of a monopile model excited by random waves. The identification results show that the approach is able to give very reliable estimates of the modal parameters. Furthermore, a comparison of the identified wave load process and the calculated load process based on the Morison equation shows...

Supply regimes in fisheries

DEFF Research Database (Denmark)

Nielsen, Max

2006-01-01

Supply in fisheries is traditionally known for its backward bending nature, owing to externalities in production. Such a supply regime, however, exist only for pure open access fisheries. Since most fisheries worldwide are neither pure open access, nor optimally managed, rather between the extremes......, the traditional understanding of supply regimes in fisheries needs modification. This paper identifies through a case study of the East Baltic cod fishery supply regimes in fisheries, taking alternative fisheries management schemes and mesh size limitations into account. An age-structured Beverton-Holt based bio......-economic supply model with mesh sizes is developed. It is found that in the presence of realistic management schemes, the supply curves are close to vertical in the relevant range. Also, the supply curve under open access with mesh size limitations is almost vertical in the relevant range, owing to constant...

Optimizing physicians' instruction of PACS through e-learning: cognitive load theory applied.

Science.gov (United States)

Devolder, P; Pynoo, B; Voet, T; Adang, L; Vercruysse, J; Duyck, P

2009-03-01

This article outlines the strategy used by our hospital to maximize the knowledge transfer to referring physicians on using a picture archiving and communication system (PACS). We developed an e-learning platform underpinned by the cognitive load theory (CLT) so that in depth knowledge of PACS' abilities becomes attainable regardless of the user's prior experience with computers. The application of the techniques proposed by CLT optimizes the learning of the new actions necessary to obtain and manipulate radiological images. The application of cognitive load reducing techniques is explained with several examples. We discuss the need to safeguard the physicians' main mental processes to keep the patient's interests in focus. A holistic adoption of CLT techniques both in teaching and in configuration of information systems could be adopted to attain this goal. An overview of the advantages of this instruction method is given both on the individual and organizational level.

Creep crack growth by grain boundary cavitation under monotonic and cyclic loading

Science.gov (United States)

Wen, Jian-Feng; Srivastava, Ankit; Benzerga, Amine; Tu, Shan-Tung; Needleman, Alan

2017-11-01

Plane strain finite deformation finite element calculations of mode I crack growth under small scale creep conditions are carried out. Attention is confined to isothermal conditions and two time histories of the applied stress intensity factor: (i) a monononic increase to a plateau value subsequently held fixed; and (ii) a cyclic time variation. The crack growth calculations are based on a micromechanics constitutive relation that couples creep deformation and damage due to grain boundary cavitation. Grain boundary cavitation, with cavity growth due to both creep and diffusion, is taken as the sole failure mechanism contributing to crack growth. The influence on the crack growth rate of loading history parameters, such as the magnitude of the applied stress intensity factor, the ratio of the applied minimum to maximum stress intensity factors, the loading rate, the hold time and the cyclic loading frequency, are explored. The crack growth rate under cyclic loading conditions is found to be greater than under monotonic creep loading with the plateau applied stress intensity factor equal to its maximum value under cyclic loading conditions. Several features of the crack growth behavior observed in creep-fatigue tests naturally emerge, for example, a Paris law type relation is obtained for cyclic loading.

Stochastic dynamical models for ecological regime shifts

DEFF Research Database (Denmark)

Møller, Jan Kloppenborg; Carstensen, Jacob; Madsen, Henrik

the physical and biological knowledge of the system, and nonlinearities introduced here can generate regime shifts or enhance the probability of regime shifts in the case of stochastic models, typically characterized by a threshold value for the known driver. A simple model for light competition between...... definition and stability of regimes become less subtle. Ecological regime shifts and their modeling must be viewed in a probabilistic manner, particularly if such model results are to be used in ecosystem management....

Study of Mechanical Features for Low Cycle Fatigue Samples of Metastable Austenitic Steel AISI 321 by Neutron Stress Analysis under Applied Load

CERN Document Server

Taran, Yu V; Eifler, D; Nebel, Th; Schreiber, J

2002-01-01

The elastoplastic properties of the austenitic matrix and martensitic volume areas induced during cyclic tensile-compressive loading of low carbon metastable austenitic stainless steel were studied in an in situ neutron diffraction stress rig experiment on the ENGIN instrument at the ISIS pulsed neutron facility. Samples prepared from the steel AISI 321 annealed at 1050 ^{\\circ}C and quenched in water were subjected to low-cycle fatigue under total-strain control with an amplitude of 1 % at a frequency of 0.5 Hz. Subsequent applied stress?elastic strain responses of the austenitic and martensitic phases were obtained by Rietveld and Le Bail refinements of the neutron diffraction spectra, and were used to determine the elastic constants of the phases as a function of fatigue level. The results of modified refinements accounting for the elastic anisotropy in polycrystalline materials under load are also presented. The residual strains in the austenitic matrix were determined as a function of fatigue cycling, us...

Finite element analysis of the biaxial cyclic tensile loading of the elastoplastic plate with the central hole: asymptotic regimes

Science.gov (United States)

Turkova, Vera; Stepanova, Larisa

2018-03-01

For elastistoplastic structure elements under cyclic loading three types of asymptotic behavior are well known: shakedown, cyclic plasticity or ratcheting. In structure elements operating in real conditions ratcheting must always be excluded since it caused the incremental fracture of structure by means of the accumulation of plastic strains. In the present study results of finite-element (FEM) calculations of the asymptotical behavior of an elastoplastic plate with the central circular and elliptic holes under the biaxial cyclic loading for three different materials are presented. Incremental cyclic loading of the sample with stress concentrator (the central hole) is performed in the multifunctional finite-element package SIMULIA Abaqus. The ranges of loads found for shakedown, cyclic plasticity and ratcheting are presented. The results obtained are generalized and analyzed. Convenient normalization is suggested. The chosen normalization allows us to present all computed results, corresponding to separate materials, within one common curve with minimum scattering of the points. Convenience of the generalized diagram consists in a possibility to find an asymptotical behavior of an inelastic structure for materials for which computer calculations were not made.

Short-term load forecasting by a neuro-fuzzy based approach

Energy Technology Data Exchange (ETDEWEB)

Ruey-Hsun Liang; Ching-Chi Cheng [National Yunlin University of Science and Technology (China). Dept. of Electrical Engineering

2002-02-01

An approach based on an artificial neural network (ANN) combined with a fuzzy system is proposed for short-term load forecasting. This approach was developed in order to reach the desired short-term load forecasting in an efficient manner. Over the past few years, ANNs have attained the ability to manage a great deal of system complexity and are now being proposed as powerful computational tools. In order to select the appropriate load as the input for the desired forecasting, the Pearson analysis method is first applied to choose two historical record load patterns that are similar to the forecasted load pattern. These two load patterns and the required weather parameters are then fuzzified and input into a neural network for training or testing the network. The back-propagation (BP) neural network is applied to determine the preliminary forecasted load. In addition, the rule base for the fuzzy inference machine contains important linguistic membership function terms with knowledge in the form of fuzzy IF-THEN rules. This produces the load correction inference from the historical information and past forecasted load errors to obtain an inferred load error. Adding the inferred load error to the preliminary forecasted load, we can obtain the finial forecasted load. The effectiveness of the proposed approach to the short-term load-forecasting problem is demonstrated using practical data from the Taiwan Power Company (TPC). (Author)

A Baseline Load Schedule for the Manual Calibration of a Force Balance

Science.gov (United States)

Ulbrich, N.; Gisler, R.

2013-01-01

A baseline load schedule for the manual calibration of a force balance is defined that takes current capabilities at the NASA Ames Balance Calibration Laboratory into account. The chosen load schedule consists of 18 load series with a total of 194 data points. It was designed to satisfy six requirements: (i) positive and negative loadings should be applied for each load component; (ii) at least three loadings should be applied between 0 % and 100 % load capacity; (iii) normal and side force loadings should be applied at the forward gage location, aft gage location, and the balance moment center; (iv) the balance should be used in "up" and "down" orientation to get positive and negative axial force loadings; (v) the constant normal and side force approaches should be used to get the rolling moment loadings; (vi) rolling moment loadings should be obtained for 0, 90, 180, and 270 degrees balance orientation. In addition, three different approaches are discussed in the paper that may be used to independently estimate the natural zeros, i.e., the gage outputs of the absolute load datum of the balance. These three approaches provide gage output differences that can be used to estimate the weight of both the metric and non-metric part of the balance. Data from the calibration of a six-component force balance will be used in the final manuscript of the paper to illustrate characteristics of the proposed baseline load schedule.

The load structure of electro boilers

International Nuclear Information System (INIS)

Feilberg, N.; Livik, K.

1995-01-01

Load measurements have been performed on 24 electro boilers with a time resolution of one hour throughout a period of one year. The boilers are used for space heating and heating of tap water in office buildings, shopping centres and apartment buildings. All boilers have tariffs with disconnection agreements. This report presents load analyses of the measurements from each boiler, and typical load profiles are calculated and presented. It also analyses how boilers are used in relation to the outdoor temperature and the power price on the spot market. All the measurements are performed in Bergen, Norway, in the period August 1993 - August 1994. Typical load profiles are shown, both annual and daily, as well as specific load parameters in addition to key figures used in calculating the total power load on the distribution network. The climate impact on energy and power load is evaluated. The report also shows examples of how the results may be applied in various special fields. 8 figs., 9 tabs

Estimation of the ancestral effective population sizes of African great apes under different selection regimes.

Science.gov (United States)

Schrago, Carlos G

2014-08-01

Reliable estimates of ancestral effective population sizes are necessary to unveil the population-level phenomena that shaped the phylogeny and molecular evolution of the African great apes. Although several methods have previously been applied to infer ancestral effective population sizes, an analysis of the influence of the selective regime on the estimates of ancestral demography has not been thoroughly conducted. In this study, three independent data sets under different selective regimes were used were composed to tackle this issue. The results showed that selection had a significant impact on the estimates of ancestral effective population sizes of the African great apes. The inference of the ancestral demography of African great apes was affected by the selection regime. The effects, however, were not homogeneous along the ancestral populations of great apes. The effective population size of the ancestor of humans and chimpanzees was more impacted by the selection regime when compared to the same parameter in the ancestor of humans, chimpanzees and gorillas. Because the selection regime influenced the estimates of ancestral effective population size, it is reasonable to assume that a portion of the discrepancy found in previous studies that inferred the ancestral effective population size may be attributable to the differential action of selection on the genes sampled.

Reliability of Estimation Pile Load Capacity Methods

Directory of Open Access Journals (Sweden)

Yudhi Lastiasih

2014-04-01

Full Text Available None of numerous previous methods for predicting pile capacity is known how accurate any of them are when compared with the actual ultimate capacity of piles tested to failure. The author’s of the present paper have conducted such an analysis, based on 130 data sets of field loading tests. Out of these 130 data sets, only 44 could be analysed, of which 15 were conducted until the piles actually reached failure. The pile prediction methods used were: Brinch Hansen’s method (1963, Chin’s method (1970, Decourt’s Extrapolation Method (1999, Mazurkiewicz’s method (1972, Van der Veen’s method (1953, and the Quadratic Hyperbolic Method proposed by Lastiasih et al. (2012. It was obtained that all the above methods were sufficiently reliable when applied to data from pile loading tests that loaded to reach failure. However, when applied to data from pile loading tests that loaded without reaching failure, the methods that yielded lower values for correction factor N are more recommended. Finally, the empirical method of Reese and O’Neill (1988 was found to be reliable enough to be used to estimate the Qult of a pile foundation based on soil data only.

Ocean Tide Loading Computation

Science.gov (United States)

Agnew, Duncan Carr

2005-01-01

September 15,2003 through May 15,2005 This grant funds the maintenance, updating, and distribution of programs for computing ocean tide loading, to enable the corrections for such loading to be more widely applied in space- geodetic and gravity measurements. These programs, developed under funding from the CDP and DOSE programs, incorporate the most recent global tidal models developed from Topex/Poscidon data, and also local tide models for regions around North America; the design of the algorithm and software makes it straightforward to combine local and global models.

A study on fire design accidental loads for aluminum safety helidecks

Directory of Open Access Journals (Sweden)

Sang Jin Kim

2016-11-01

Full Text Available The helideck structure must satisfy the safety requirements associated with various environmental and accidental loads. Especially, there have been a number of fire accidents offshore due to helicopter collision (take-off and/or landing in recent decades. To prevent further accidents, a substantial amount of effort has been directed toward the management of fire in the safety design of offshore helidecks. The aims of this study are to introduce and apply a procedure for quantitative risk assessment and management of fires by defining the fire loads with an applied example. The frequency of helicopter accidents are considered, and design accidental levels are applied. The proposed procedures for determining design fire loads can be efficiently applied in offshore helideck development projects.

Exploring the Possible Use of Information Barriers for future Biological Weapons Verification Regimes

International Nuclear Information System (INIS)

Luke, S.J.

2011-01-01

genetic information associated with the various pathogens. In addition, it has been determined that a suitable information barrier could be applied to this technology when the verification regime has been defined. Finally, the report posits a path forward for additional development of information barriers in a biological weapons verification regime. This path forward has shown that a new analysis approach coined as Information Loss Analysis might need to be pursued so that a numerical understanding of how information can be lost in specific measurement systems can be achieved.

Exploring the Possible Use of Information Barriers for future Biological Weapons Verification Regimes

Energy Technology Data Exchange (ETDEWEB)

Luke, S J

2011-12-20

genetic information associated with the various pathogens. In addition, it has been determined that a suitable information barrier could be applied to this technology when the verification regime has been defined. Finally, the report posits a path forward for additional development of information barriers in a biological weapons verification regime. This path forward has shown that a new analysis approach coined as Information Loss Analysis might need to be pursued so that a numerical understanding of how information can be lost in specific measurement systems can be achieved.

A two-phase flow regime map for a MAPLE-type nuclear research reactor fuel channel: Effect of hexagonal finned bundle

International Nuclear Information System (INIS)

Harvel, G.D.; Chang, J.S.

1997-01-01

A two-phase flow regime map is developed experimentally and theoretically for a vertical hexagonal flow channel with and without a 36-finned rod hexagonal bundle. This type of flow channel is of interest to MAPLE-type nuclear research reactors. The flow regime maps are determined by visual observations and observation of waveforms shown by a capacitance-type void fraction meter. The experimental results show that the inclusion of the finned hexagonal bundle shifts the flow regime transition boundaries toward higher water flow rates. Existing flow regime maps based on pipe flow require slight modifications when applied to the hexagonal flow channel with and without a MAPLE-type finned hexagonal bundle. The proposed theoretical model agrees well with experimental results

De Facto Regimes in International Law

OpenAIRE

Essen, Jonte van

2012-01-01

The ambiguous position of de facto regimes in international law has long been the subject of scholarly debate and a source of political conflict. An assessment of the current standing of these regimes in international law and the consequences of actions by international actors on this status has, however, been long overdue. The manner in which de facto regimes are regarded internationally has serious consequences for the individuals under the influence of this legal grey area. Therefore, the ...

The tensile deformation behavior of nuclear-grade isotropic graphite posterior to hydrostatic loading

International Nuclear Information System (INIS)

Yoda, S.; Eto, M.

1983-01-01

The effects of prehydrostatic loading on microstructural changes and tensile deformation behavior of nuclear-grade isotropic graphite have been examined. Scanning electron micrographs show that formation of microcracks associated with delamination between basal planes occurs under hydrostatic loading. Hydrostatic loading on specimens results in the decrease in tensile strength and increase in residual strain generated by the applied tensile stress at various levels, indicating that the graphite material is weakened by hydrostatic loading. A relationship between residual strain and applied tensile stress for graphite hydrostatically-loaded at several pressure levels can be approximately expressed as element of= (AP + B) sigmasup(n) over a wide range hydrostatic pressure, where element of, P and sigma denote residual strain, hydrostatic pressure and applied tensile stress, respectively; A, B and n are constant. The effects of prehydrostatic loading on the tensile stress-strain behavior of the graphite were examined in more detail. The ratio of stress after hydrostatic loading to that before hydrostatic loading on the stress-strain relationship remains almost unchanged irrespective of strain. (orig.)

High thermal load receiving heat plate

International Nuclear Information System (INIS)

Shibutani, Jun-ichi; Shibayama, Kazuhito; Yamamoto, Keiichi; Uchida, Takaho.

1993-01-01

The present invention concerns a high thermal load heat receiving plate such as a divertor plate of a thermonuclear device. The high thermal load heat receiving plate of the present invention has a cooling performance capable of suppressing the temperature of an armour tile to less than a threshold value of the material against high thermal loads applied from plasmas. Spiral polygonal pipes are inserted in cooling pipes at a portion receiving high thermal loads in the high temperature load heat receiving plate of the present invention. Both ends of the polygonal pipes are sealed by lids. An area of the flow channel in the cooling pipes is thus reduced. Heat conductivity on the cooling surface of the cooling pipes is increased in the high thermal load heat receiving plate having such a structure. Accordingly, temperature elevation of the armour tile can be suppressed. (I.S.)

Transient regimes in a heavy water reactor; Regimes transitoires dans un reacteur a eau lourde

Energy Technology Data Exchange (ETDEWEB)

Raievski, V [Commissariat a l' Energie Atomique, Saclay(France). Centre d' Etudes Nucleaires

1953-07-01

We studied the variations of power and reactivity of a reactor when we raise in a continuous way the starting plates. During the subcritical regime (negative reactivity), the power is determined by reactivity and by the intensity of the sources of photo neutrons, produced during the previous work of the reactor. When, during the rise of the plates, the reactor, pass by the critical regime (zero reactivity), one notes that the reached power is independent of the initial reactivity. During the sur-critical regime (positive reactivity), the elevation of temperature of the uranium bars slows down the growth of reactivity due to the movements of the plates. The power stretches then toward a value that depends only on the regime of cooling of the reactor and the excess of the available reactivity. This survey permits to choose such a rise speed, that reactivity remains constantly lower to a value beyond which the piloting of the reactor becomes difficult. This result is not more valid, if the intensity of the sources is insufficient, what takes place during the first divergences and after a stop of long length. (author) [French] On etudie les variations de puissance et de reactivite d'un reacteur quand on leve d'une facon continue les plaques de demarrage. Pendant le regime subcritique (reactivite negative), la puissance est determinee par la reactivite et par l'intensite des sources de photoneutrons, produites pendant la marche anterieure du reacteur. Quand, au cours de la montee des plaques, le reacteur passe par le regime critique (reactivite nulle), on constate que la puissance atteinte est independante de la reactivite initiale. Pendant le regime surcritique (reactivite positive), l'elevation de temperature des barres d'uranium ralentit l'accroissement de reactivite due aux mouvements des plaques. La puissance tend alors vers une valeur qui ne depend plus que du regime de refroidissement du reacteur et de l'exces de la reactivite disponible. Cette etude permet de

Comparison of infrared and 3D digital image correlation techniques applied for mechanical testing of materials

Science.gov (United States)

Krstulović-Opara, Lovre; Surjak, Martin; Vesenjak, Matej; Tonković, Zdenko; Kodvanj, Janoš; Domazet, Željko

2015-11-01

To investigate the applicability of infrared thermography as a tool for acquiring dynamic yielding in metals, a comparison of infrared thermography with three dimensional digital image correlation has been made. Dynamical tension tests and three point bending tests of aluminum alloys have been performed to evaluate results obtained by IR thermography in order to detect capabilities and limits for these two methods. Both approaches detect pastification zone migrations during the yielding process. The results of the tension test and three point bending test proved the validity of the IR approach as a method for evaluating the dynamic yielding process when used on complex structures such as cellular porous materials. The stability of the yielding process in the three point bending test, as contrary to the fluctuation of the plastification front in the tension test, is of great importance for the validation of numerical constitutive models. The research proved strong performance, robustness and reliability of the IR approach when used to evaluate yielding during dynamic loading processes, while the 3D DIC method proved to be superior in the low velocity loading regimes. This research based on two basic tests, proved the conclusions and suggestions presented in our previous research on porous materials where middle wave infrared thermography was applied.

Fire Regime Characteristics along Environmental Gradients in Spain

Directory of Open Access Journals (Sweden)

María Vanesa Moreno

2016-11-01

Full Text Available Concern regarding global change has increased the need to understand the relationship between fire regime characteristics and the environment. Pyrogeographical theory suggests that fire regimes are constrained by climate, vegetation and fire ignition processes, but it is not obvious how fire regime characteristics are related to those factors. We used a three-matrix approach with a multivariate statistical methodology that combined an ordination method and fourth-corner analysis for hypothesis testing to investigate the relationship between fire regime characteristics and environmental gradients across Spain. Our results suggest that fire regime characteristics (i.e., density and seasonality of fire activity are constrained primarily by direct gradients based on climate, population, and resource gradients based on forest potential productivity. Our results can be used to establish a predictive model for how fire regimes emerge in order to support fire management, particularly as global environmental changes impact fire regime characteristics.

Power load prediction based on GM (1,1)

Science.gov (United States)

Wu, Di

2017-05-01

Currently, Chinese power load prediction is highly focused; the paper deeply studies grey prediction and applies it to Chinese electricity consumption during the recent 14 years; through after-test test, it obtains grey prediction which has good adaptability to medium and long-term power load.

Undrained Response of Bucket Foundations to Moment Loading

DEFF Research Database (Denmark)

Barari, Amin; Ibsen, Lars Bo

2012-01-01

geotechnical engineers. This paper presents the experimental and numerical results of moment loading on small scale models of bucket foundations installed on Yoldia clay. The moment loading is experienced via the horizontal forces applied to features on a tower installed on bucket foundations. Different arm...

Determination of aerodynamic sensitivity coefficients in the transonic and supersonic regimes

Science.gov (United States)

Elbanna, Hesham M.; Carlson, Leland A.

1989-01-01

The quasi-analytical approach is developed to compute airfoil aerodynamic sensitivity coefficients in the transonic and supersonic flight regimes. Initial investigation verifies the feasibility of this approach as applied to the transonic small perturbation residual expression. Results are compared to those obtained by the direct (finite difference) approach and both methods are evaluated to determine their computational accuracies and efficiencies. The quasi-analytical approach is shown to be superior and worth further investigation.

Applying chemical engineering concepts to non-thermal plasma reactors

Science.gov (United States)

Pedro AFFONSO, NOBREGA; Alain, GAUNAND; Vandad, ROHANI; François, CAUNEAU; Laurent, FULCHERI

2018-06-01

Process scale-up remains a considerable challenge for environmental applications of non-thermal plasmas. Undersanding the impact of reactor hydrodynamics in the performance of the process is a key step to overcome this challenge. In this work, we apply chemical engineering concepts to analyse the impact that different non-thermal plasma reactor configurations and regimes, such as laminar or plug flow, may have on the reactor performance. We do this in the particular context of the removal of pollutants by non-thermal plasmas, for which a simplified model is available. We generalise this model to different reactor configurations and, under certain hypotheses, we show that a reactor in the laminar regime may have a behaviour significantly different from one in the plug flow regime, often assumed in the non-thermal plasma literature. On the other hand, we show that a packed-bed reactor behaves very similarly to one in the plug flow regime. Beyond those results, the reader will find in this work a quick introduction to chemical reaction engineering concepts.

Kalman-fuzzy algorithm in short term load forecasting

International Nuclear Information System (INIS)

Shah Baki, S.R.; Saibon, H.; Lo, K.L.

1996-01-01

A combination of Kalman-Fuzzy-Neural is developed to forecast the next 24 hours load. The input data fed to neural network are presented with training data set composed of historical load data, weather, day of the week, month of the year and holidays. The load data is fed through Kalman-Fuzzy filter before being applied to Neural Network for training. With this techniques Neural Network converges faster and the mean percentage error of predicted load is reduced as compared to the classical ANN technique

Feasibility of Applying Active Lubrication to Dynamically Loaded Fluid Film Bearings

DEFF Research Database (Denmark)

Estupinan, Edgar Alberto; Santos, Ilmar

2009-01-01

The feasibility of modifying the dynamics of the thin fluid films of dynamically loaded journal bearings, using different strategies of active lubrication is studied in this work. A significant reduction in the vibration levels, wear and power friction losses, is expected. Particularly, the focus...... of this study is on the analysis of main crankshaft bearings, where the conventional hydrodynamic lubrication is modified by injecting oil at actively controllable pressures, through orifices circumferentially located along the bearing surface....

Short-term forecasting of individual household electricity loads with investigating impact of data resolution and forecast horizon

Directory of Open Access Journals (Sweden)

Yildiz Baran

2018-01-01

Full Text Available Smart grid components such as smart home and battery energy management systems, high penetration of renewable energy systems, and demand response activities, require accurate electricity demand forecasts for the successful operation of the electricity distribution networks. For example, in order to optimize residential PV generation and electricity consumption and plan battery charge-discharge regimes by scheduling household appliances, forecasts need to target and be tailored to individual household electricity loads. The recent uptake of smart meters allows easier access to electricity readings at very fine resolutions; hence, it is possible to utilize this source of available data to create forecast models. In this paper, models which predominantly use smart meter data alongside with weather variables, or smart meter based models (SMBM, are implemented to forecast individual household loads. Well-known machine learning models such as artificial neural networks (ANN, support vector machines (SVM and Least-Square SVM are implemented within the SMBM framework and their performance is compared. The analysed household stock consists of 14 households from the state of New South Wales, Australia, with at least a year worth of 5 min. resolution data. In order for the results to be comparable between different households, our study first investigates household load profiles according to their volatility and reveals the relationship between load standard deviation and forecast performance. The analysis extends previous research by evaluating forecasts over four different data resolution; 5, 15, 30 and 60 min, each resolution analysed for four different horizons; 1, 6, 12 and 24 h ahead. Both, data resolution and forecast horizon, proved to have significant impact on the forecast performance and the obtained results provide important insights for the operation of various smart grid applications. Finally, it is shown that the load profile of some

Short-term forecasting of individual household electricity loads with investigating impact of data resolution and forecast horizon

Science.gov (United States)

Yildiz, Baran; Bilbao, Jose I.; Dore, Jonathon; Sproul, Alistair B.

2018-05-01

Smart grid components such as smart home and battery energy management systems, high penetration of renewable energy systems, and demand response activities, require accurate electricity demand forecasts for the successful operation of the electricity distribution networks. For example, in order to optimize residential PV generation and electricity consumption and plan battery charge-discharge regimes by scheduling household appliances, forecasts need to target and be tailored to individual household electricity loads. The recent uptake of smart meters allows easier access to electricity readings at very fine resolutions; hence, it is possible to utilize this source of available data to create forecast models. In this paper, models which predominantly use smart meter data alongside with weather variables, or smart meter based models (SMBM), are implemented to forecast individual household loads. Well-known machine learning models such as artificial neural networks (ANN), support vector machines (SVM) and Least-Square SVM are implemented within the SMBM framework and their performance is compared. The analysed household stock consists of 14 households from the state of New South Wales, Australia, with at least a year worth of 5 min. resolution data. In order for the results to be comparable between different households, our study first investigates household load profiles according to their volatility and reveals the relationship between load standard deviation and forecast performance. The analysis extends previous research by evaluating forecasts over four different data resolution; 5, 15, 30 and 60 min, each resolution analysed for four different horizons; 1, 6, 12 and 24 h ahead. Both, data resolution and forecast horizon, proved to have significant impact on the forecast performance and the obtained results provide important insights for the operation of various smart grid applications. Finally, it is shown that the load profile of some households vary

Canadian oil spill response capability - an investigation of the proposed fee regime

International Nuclear Information System (INIS)

Gold, E.; Gratwick, J.; Yee, P.

1996-08-01

Canada's oil spill response capability and its fee structure was examined and assessed. The present regime consists of five industry-owned oil spill response organizations who provide response teams throughout Canadian waters, except the Arctic. These organizations are fully adequate to meet the standards set by the Canadian Coast Guard. However, the Canadian Coast Guard withdrew from active control of the fee regime, leaving it to each response team to determine its own fee structure. The expectation was that the market would be capable of controlling the fees to be charged. This did not happen, and the investigative panel came to the conclusion that the present regime was not workable. In view of the situation the Panel concluded that ensuring oil spill response capability in Canada must always be the sole responsibility of the Canadian Government. Eleven recommendations were detailed in this final report. The most important recommendation was that the Canadian Coast Guard should re-establish its principal role in the oil spill response area. It was also suggested that there should be a single, national fee structure applying to the whole country except the Arctic, and that the fee should be collected by an independent national agency

Not traditional regimes of radiotherapeutic dose fractionation as modifier of radiotherapy for carcinoma of lungs

International Nuclear Information System (INIS)

Artemova, N.A.

2008-01-01

The efficiency of applying various of radiotherapeutic dose fractionation was analyzed. The results of the own studies performed at the Scientific and Research Institute of Oncology and Medical Radiology for elaborating not traditional regimes of radiotherapeutic dose fractionation (a dynamic fractionation applying enlarged regimes at the first stage and the classic ones at the second stage) were presented. Appliance of the modified radiotherapy for the epidermoid carcinoma of the lungs allowed to increase the objective response from 45,3+-3% to 80+-5% the tumor disappearing completely in 40+-6% of patients as compared with 10+-2%. Appliance of the intensive not traditional variant of the radiotherapy dynamic fractionation in case of a small cell carcinoma of the lungs resulted in the therapy duration reduction from 6 to 4 weeks. Thus the not traditional dose fractionation might become a mechanism for the improving the radiotherapy of persons suffering from the carcinoma of the lungs. (authors)

Framing of regimes and transition strategies

DEFF Research Database (Denmark)

Jensen, Jens Stissing

2012-01-01

This article suggests that transition strategies are always formulated in the context of specific representations of the regime and the challenges it faces. It is argued that the framing of a regime affects the envisioning of transition strategies. An analysis of the current development agenda...... for the housing construction sector in Denmark reveals the relevance and impacts of different regime framings. It is proposed that the ability to cope with framing issues as situated and political processes is at the core of the governance of transitions....

STOCHASTIC DESCRIPTION OF THE HIGH-FREQUENCY CONTENT OF DAILY SUNSPOTS AND EVIDENCE FOR REGIME CHANGES

International Nuclear Information System (INIS)

Shapoval, A.; Le Mouël, J.-L.; Courtillot, V.; Shnirman, M.

2015-01-01

The irregularity index λ is applied to the high-frequency content of daily sunspot numbers ISSN. This λ is a modification of the standard maximal Lyapunov exponent. It is computed here as a function of embedding dimension m, within four-year time windows centered at the maxima of Schwabe cycles. The λ(m) curves form separate clusters (pre-1923 and post-1933). This supports a regime transition and narrows its occurrence to cycle 16, preceding the growth of activity leading to the Modern Maximum. The two regimes are reproduced by a simple autoregressive process AR(1), with the mean of Poisson noise undergoing 11 yr modulation. The autocorrelation a of the process (linked to sunspot lifetime) is a ≈ 0.8 for 1850-1923 and ≈0.95 for 1933-2013. The AR(1) model suggests that groups of spots appear with a Poisson rate and disappear at a constant rate. We further applied the irregularity index to the daily sunspot group number series for the northern and southern hemispheres, provided by the Greenwich Royal Observatory (RGO), in order to study a possible desynchronization. Correlations between the north and south λ(m) curves vary quite strongly with time and indeed show desynchronization. This may reflect a slow change in the dimension of an underlying dynamical system. The ISSN and RGO series of group numbers do not imply an identical mechanism, but both uncover a regime change at a similar time. Computation of the irregularity index near the maximum of cycle 24 will help in checking whether yet another regime change is under way

Ecosystem regime shifts disrupt trophic structure.

Science.gov (United States)

Hempson, Tessa N; Graham, Nicholas A J; MacNeil, M Aaron; Hoey, Andrew S; Wilson, Shaun K

2018-01-01

Regime shifts between alternative stable ecosystem states are becoming commonplace due to the combined effects of local stressors and global climate change. Alternative states are characterized as substantially different in form and function from pre-disturbance states, disrupting the delivery of ecosystem services and functions. On coral reefs, regime shifts are typically characterized by a change in the benthic composition from coral to macroalgal dominance. Such fundamental shifts in the benthos are anticipated to impact associated fish communities that are reliant on the reef for food and shelter, yet there is limited understanding of how regime shifts propagate through the fish community over time, relative to initial or recovery conditions. This study addresses this knowledge gap using long-term data of coral reef regime shifts and recovery on Seychelles reefs following the 1998 mass bleaching event. It shows how trophic structure of the reef fish community becomes increasingly dissimilar between alternative reef ecosystem states (regime-shifted vs. recovering) with time since disturbance. Regime-shifted reefs developed a concave trophic structure, with increased biomass in base trophic levels as herbivorous species benefitted from increased algal resources. Mid trophic level species, including specialists such as corallivores, declined with loss of coral habitat, while biomass was retained in upper trophic levels by large-bodied, generalist invertivores. Recovering reefs also experienced an initial decline in mid trophic level biomass, but moved toward a bottom-heavy pyramid shape, with a wide range of feeding groups (e.g., planktivores, corallivores, omnivores) represented at mid trophic levels. Given the importance of coral reef fishes in maintaining the ecological function of coral reef ecosystems and their associated fisheries, understanding the effects of regime shifts on these communities is essential to inform decisions that enhance ecological

Development of an in vitro three dimensional loading-measurement system for long bone fixation under multiple loading conditions: a technical description

Directory of Open Access Journals (Sweden)

Wilson David A

2007-11-01

Full Text Available Abstract The purpose of this investigation was to design and verify the capabilities of an in vitro loading-measurement system that mimics in vivo unconstrained three dimensional (3D relative motion between long bone ends, applies uniform load components over the entire length of a test specimen, and measures 3D relative motion between test segment ends to directly determine test segment construct stiffness free of errors due to potting-fixture-test machine finite stiffness. Intact equine cadaveric radius bones, which were subsequently osteotomized/ostectomized and instrumented with bone plates were subjected to non-destructive axial, torsion, and 4-point bending loads through fixtures designed to allow unconstrained components of non-load associated 3D relative motion between radius ends. 3D relative motion between ends of a 50 mm long test segment was measured by an infrared optical tracking system to directly determine its stiffness. Each specimen was then loaded to ultimate failure in either torsion or bending. Cortical bone cross-section diameters and published bone biomechanical properties were substituted into classical mechanics equations to predict the intact test segment theoretical stiffness for comparison and thus loading-measurement system verification. Intact measured stiffness values were the same order of magnitude as theoretically predicted. The primary component of relative motion between ends of the test segment corresponded to that of the applied load with the other 3D components being evident and consistent in relative magnitude and direction for unconstrained loading of an unsymmetrical double plate oblique fracture configuration. Bone failure configurations were reproducible and consistent with theoretically predicted. The 3D loading-measurement system designed: a mimics unconstrained relative 3D motion between radius ends that occurs in clinical situations, b applies uniform compression, torsion, and 4-point bending loads

Feasibility of a dual regime gyrotron

International Nuclear Information System (INIS)

Sawant, Ashwini; Jain, Prerit; Kartikeyan, M.V.

2012-01-01

The design concept of a 42/84 GHz, 500 kW, CW, dual-regime gyrotron for ECRH of plasma in an experimental Tokamak will be presented in this paper. Operation at 42 GHz is fundamental where as that in 84 GHz will be second harmonic so that a similar guidance system will be retained for dual regime operation. In this paper, the mode competition and mode selection procedures are presented for such a dual regime operation. Cold cavity design and self-consistent calculations will be carried out for power and efficiencies. (author)

Material Surface Damage under High Pulse Loads Typical for ELM Bursts and Disruptions in ITER

Energy Technology Data Exchange (ETDEWEB)

Landman, I.S.; Pestchanyi, S.E.; Bazylev, B.N [Forschungszentrum Karlsruhe (Germany). Inst. for Pulsed Power and Microwave Technology; Safronov, V.M. [Troitsk Inst. for Innovation and Fusion Research (TRINITI) (Russian Federation); Garkusha, I.E. [Kharkov Inst. of Physics and Technology (KIPT) (Ukraine). Inst. of Plasma Physics

2004-08-01

The divertor armour material for the tokamak ITER will probably be carbon manufactured as fibre composites (CFC) and tungsten as either brush-like structures or thin plates. Disruptive pulse loads where the heat deposition Q may reach 10{sup 2} MJ/m{sup 2} on a time scale {tau} of 3 ms, or operation in the ELMy H-mode at repetitive loads with Q {approx} 3MJ/m{sup 2} and {tau}{approx}0.3 ms; deteriorate armour performance. This work surveys recent numerical and experimental investigations of erosion mechanisms at these off-normal regimes carried out at FZK, TRINITI, and IPP-Kharkov. The modelling uses the anisotropic thermomechanics code PEGASUS-3D for the simulation of CFC brittle destruction, the surface melt motion code MEMOS-1.5D for tungsten targets, and the radiation-magnetohydrodynamics code FOREV-2D for calculating the plasma impact and simulating the heat loads for the ITER regime. Experiments aimed at validating these codes are being carried out at the plasma gun facilities MK-200UG, QSPA-T, and QSPA-Kh50 which produce powerful streams of hydrogen plasma with Q=10-30MJ/m{sup 2} and {tau} = 0.03-0.5 ms. Essential results are, for CFC targets, the experiments at high heat loads and the development of a local overheating model incorporated in PEGASUS-3D, and for the tungsten targets the analysis of evaporation- and melt motion erosion on the base of MEMOS-1.5D calculations for repetitive ELMs.

Material Surface Damage under High Pulse Loads Typical for ELM Bursts and Disruptions in ITER

Science.gov (United States)

Landman, I. S.; Pestchanyi, S. E.; Safronov, V. M.; Bazylev, B. N.; Garkusha, I. E.

The divertor armour material for the tokamak ITER will probably be carbon manufactured as fibre composites (CFC) and tungsten as either brush-like structures or thin plates. Disruptive pulse loads where the heat deposition Q may reach 102 MJ/m 2 on a time scale Ïä of 3 ms, or operation in the ELMy H-mode at repetitive loads with Q âe 1/4 3 MJ/m2 and Ïä âe 1/4 0.3 ms, deteriorate armour performance. This work surveys recent numerical and experimental investigations of erosion mechanisms at these off-normal regimes carried out at FZK, TRINITI, and IPP-Kharkov. The modelling uses the anisotropic thermomechanics code PEGASUS-3D for the simulation of CFC brittle destruction, the surface melt motion code MEMOS-1.5D for tungsten targets, and the radiation-magnetohydrodynamics code FOREV-2D for calculating the plasma impact and simulating the heat loads for the ITER regime. Experiments aimed at validating these codes are being carried out at the plasma gun facilities MK-200UG, QSPA-T, and QSPA-Kh50 which produce powerful streams of hydrogen plasma with Q = 10–30 MJ/m2 and Ïä = 0.03–0.5 ms. Essential results are, for CFC targets, the experiments at high heat loads and the development of a local overheating model incorporated in PEGASUS-3D, and for the tungsten targets the analysis of evaporation- and melt motion erosion on the base of MEMOS-1.5D calculations for repetitive ELMs.

Foucault and the Architecture of Surveillance: Creating Regimes of Power in Schools, Shrines, and Society

Science.gov (United States)

Piro, Joseph M.

2008-01-01

Michel Foucault's critical studies concerning regimes of power are of special interest when applied to architecture. In particular, he warned of the hazards of building surveillance into architectural structures for the purpose of monitoring people and took as his historical exemplar English philosopher Jeremy Bentham's "Panopticon," a structure…

EFFECT OF FLIPPED LEARNING ON COGNITIVE LOAD: A HIGHER EDUCATION RESEARCH

Directory of Open Access Journals (Sweden)

Celal Karaca

2017-01-01

Full Text Available The purpose of this study is to determine the effect of the flipped learning method on the cognitive load of the students. The study was conducted with a sample of 160 people who were trained in Department of Mechanical Engineering for algorithms and programming courses at a higher education level. The study, which lasted for 8 weeks, has a semi-experimental design. A 9-point scale developed by Paas and Van Merrienboer (1993 was used for cognitive load measurements. At the end of the weekly courses, the scale was filled by the experimental and control groups. Independent sample t test was applied through SPSS 24 program to the obtained data. In both instances, the cognitive load in the experimental group in which the flipped learning method was applied was found to be lower than the cognitive load in the control group in which traditional face-to-face training was applied. As a result, it can be said that flipped learning, if well structured, is a method reducing cognitive load.

Structural response of full-scale concrete bridges subjected to high load magnitudes

DEFF Research Database (Denmark)

Halding, Philip Skov; Schmidt, Jacob Wittrup; Jensen, Thomas Westergaard

-shaped concrete elements. The test method is outlined in the paper, which includes a description of a novel test-rig used to apply a high magnitude loading. It was shown that the test rig could perform controlled testing in only one day, which is an important aspect, since available time (due to traffic...... disturbance) often is an issue when testing on site. Also, different types of measuring equipment such as lasers, LVDT’s and DIC-cameras was investigated, in order to evaluate the deformations during loading of one of the OT-beam bridges. The monitoring equipment was studied to verify if such equipment...... efficiently could be used for in-situ measurements. The load was applied semi-deformation controlled by a combination of dead load and hydraulic jacks. The novel high magnitude loading-rig worked well. It was also possible to achieve good readings from the monitoring equipment in combination with the applied...

Two-Phase Flow Regimes and Discharge Characteristics of a Plasma Electrohydrodynamic Atomization

International Nuclear Information System (INIS)

Sun Ming; Borocilo, D.; Harvel, G. D.; Chang, J. S.; Ibe, M.; Matsubara, H.; Hirata, H.; Fanson, P.

2011-01-01

Experimental investigation was conducted to study the flow regimes and discharge characteristics of plasma electrohydrodynamic atomization (EHDA) for decane (C 10 H 22 ) under pulsed applied negative voltage. The experimental parameters were set as the flow rate of decane from 0 mL/min to 10 mL/min and the DC charging voltage from DC 0 V to 12 V with a pulse repetition rates of 200 Hz. The flow regime of decane was observed and the volume-to-electrical charge ratio was measured. Unlike a conventional EHDA system, the results show that a corona discharge was initiated at the edge of the hollow electrode at a specific corona on-set voltage of -17 kV or -20 kV in the case with or without decane flow, respectively. This phenomenon was defined as plasma EHDA.

Effects of moving dynamic tyre loads on tyre-pavement contact stresses

CSIR Research Space (South Africa)

Steyn, WJvdM

2002-01-01

Full Text Available The purpose of this paper is to indicate the effect that moving dynamic tyre loads has on the tyre-pavement contact stresses used in pavement analysis. Traditionally tyre loads (in pavement analysis) are modelled as constant loads applied through...

Performance of Geosynthetic-Reinforced Soils Under Static and Cyclic Loading

Directory of Open Access Journals (Sweden)

M. Touahmia

2017-04-01

Full Text Available This paper investigates and discusses the composite behavior of geosynthetic reinforced soil mass. It presents the results of a series of large-scale laboratory tests supported by analytical methods to examine the performance of geogrid reinforcement subjected to static and cyclic pullout loading. The testing equipment and procedures used for this investigation are outlined. The results show that geosynthetic reinforcement can mobilize great resistance to static pulling load under high confining pressures. The reinforcement exhibits gradual deformation under cyclic loading showing no sign of imminent pullout failure for all levels of applied loads. In general, the results demonstrate that geosynthetic can be used in situations where loads are non-static, although care will be required in ensuring that appropriate factors of safety are applied to control the resulting deformation. A simplified analytical model for calculating the pulling capacity of geosynthetic reinforcement is proposed.

Fiscal Policy and Welfare under Different Exchange Rate Regimes

DEFF Research Database (Denmark)

Østrup, Finn

a representativeindividual's utility, it is demonstrated that there are differences betweenexchange rate regimes with respect to the level of government spending. Thesedifferences arise first because a rise in government spending affects macroeconomicvariables differently under different exchange rate regimes......, and secondbecause the government's inclination to expand government spending is affectedby inflation which depends on the exchange rate regime. At low rates of inflation,the government is inclined to set a higher level of government spending under afixed exchange rate regime than under a floating exchange rate...... regime in whichthe monetary authority optimises preferences which include an employment targetand an inflation target. As government spending affects the representativeindividual's utility, the choice of exchange rate regime has an impact on welfare.Keywords: exchange rate regimes; fiscal policy...

Neural network based adaptive control for nonlinear dynamic regimes

Science.gov (United States)

Shin, Yoonghyun

Adaptive control designs using neural networks (NNs) based on dynamic inversion are investigated for aerospace vehicles which are operated at highly nonlinear dynamic regimes. NNs play a key role as the principal element of adaptation to approximately cancel the effect of inversion error, which subsequently improves robustness to parametric uncertainty and unmodeled dynamics in nonlinear regimes. An adaptive control scheme previously named 'composite model reference adaptive control' is further developed so that it can be applied to multi-input multi-output output feedback dynamic inversion. It can have adaptive elements in both the dynamic compensator (linear controller) part and/or in the conventional adaptive controller part, also utilizing state estimation information for NN adaptation. This methodology has more flexibility and thus hopefully greater potential than conventional adaptive designs for adaptive flight control in highly nonlinear flight regimes. The stability of the control system is proved through Lyapunov theorems, and validated with simulations. The control designs in this thesis also include the use of 'pseudo-control hedging' techniques which are introduced to prevent the NNs from attempting to adapt to various actuation nonlinearities such as actuator position and rate saturations. Control allocation is introduced for the case of redundant control effectors including thrust vectoring nozzles. A thorough comparison study of conventional and NN-based adaptive designs for a system under a limit cycle, wing-rock, is included in this research, and the NN-based adaptive control designs demonstrate their performances for two highly maneuverable aerial vehicles, NASA F-15 ACTIVE and FQM-117B unmanned aerial vehicle (UAV), operated under various nonlinearities and uncertainties.

Fano-Kondo and the Kondo box regimes crossover in a quantum dot coupled to a quantum box

Science.gov (United States)

Apel, Victor M.; Orellana, Pedro A.; Pacheco, Monica; Anda, Enrique V.

2013-12-01

In this work, we study the Kondo effect of a quantum dot (QD) connected to leads and to a discrete set of one-particle states provided by a quantum box represented by a quantum ring (QR) pierced by a magnetic flux side attached to the QD. The interplay between the bulk Kondo effect and the so-called Kondo box regime is studied. In this system the QR energies can be continuously modified by the application of the magnetic field. The crossover between these two regimes is analyzed by changing the connection of the QD to the QR from the weak to the strong coupling regime. In the weak coupling regime, the differential conductance develops a sequence of Fano-Kondo anti-resonances due to destructive interference between the discrete quantum ring levels and the conducting Kondo channel provided by the leads. In the strong coupling regime the differential conductance has very sharp resonances when one of the Kondo discrete sub-levels characterizing the Kondo box is tuned by the applied potential. The conductance, the current fluctuations and the Fano coefficient result as being the relevant physical magnitudes to be analyzed to reveal the physical properties of these two Kondo regimes and the crossover region between them. The results were obtained by using the slave boson mean field theory (SBMFT).

The Two Regimes of Postwar Shipping

DEFF Research Database (Denmark)

Iversen, Martin Jes; Tenold, Stig

2014-01-01

the bargaining that accompanied the shift from the national regime to the competitive regime. Specifically, we show that the new regime primarily accommodated the interests of private actors such as shipping companies, rather than the interests of the authorities and the trade unions.......The aim of this article is to illustrate the most important changes in the regulatory framework of the shipping sector from the 1960s to 2010, and to analyse the basis for, and effects of, these changes. In order to explain how the transformation has occurred, we use two traditional maritime...... nations—Denmark and Norway—as case studies. First, we introduce the two regimes of Danish and Norwegian shipping: ‘the national regime’ from the early 1960s to the mid-1970s; and ‘the competitive regime’, which was fully established by the middle of the 1990s and still persists. Then, we briefly sketch...

Wavelet neural network load frequency controller

International Nuclear Information System (INIS)

Hemeida, Ashraf Mohamed

2005-01-01

This paper presents the feasibility of applying a wavelet neural network (WNN) approach for the load frequency controller (LFC) to damp the frequency oscillations of two area power systems due to load disturbances. The present intelligent control system trained the wavelet neural network (WNN) controller on line with adaptive learning rates, which are derived in the sense of a discrete type Lyapunov stability theorem. The present WNN controller is designed individually for each area. The proposed technique is applied successfully for a wide range of operating conditions. The time simulation results indicate its superiority and effectiveness over the conventional approach. The effects of consideration of the governor dead zone on the system performance are studied using the proposed controller and the conventional one

The effect of load-controlled bending load on the failure pressure of wall-thinned pipe elbows

International Nuclear Information System (INIS)

Kim, Jin Weon; Yoon, Min Soo; Park, Chi Yong

2013-01-01

Highlights: • We evaluated bending load effect on the failure pressure of wall-thinned pipe elbows. • Burst tests were conducted on real-scale elbow specimens with local wall thinning. • The tests were performed under combined pressure and load-controlled bending. • Load-controlled bending reduced the failure pressure of wall-thinned elbows. • Bending load effect was significant for opening-mode and intrados wall-thinning case. - Abstract: In this research, burst tests were conducted on real-scale elbow specimens, each with an artificial local wall-thinning defect, under combined internal pressure and constant in-plane bending load, as well as under simple internal pressure, to evaluate the effect of load-controlled bending load on the failure pressure of locally wall-thinned pipe elbows. Ninety-degree, 65A Schedule 80 elbows, with wall-thinning defects in the intrados and extrados, were used as specimens. The bending loads were in-plane opening- and closing-mode bending, applied in load-control mode. The results clearly indicated that a load-controlled in-plane bending load reduced the failure pressure of wall-thinned pipe elbows, in contrast to observations previously made under displacement-controlled bending conditions. The effect of the bending load was more significant for opening-mode than for closing-mode bending, regardless of the wall-thinning location in the elbow. Also, the effect was greater when the wall-thinning defect was located in the intrados region of the elbow, rather than the extrados region. Existing models that have been proposed to evaluate the failure of wall-thinned elbows under simple internal pressure conservatively predicted the failure pressure of elbows subjected to a combined internal pressure and load-controlled bending load

Effect of load transients on SOFC operation—current reversal on loss of load

Science.gov (United States)

Gemmen, Randall S.; Johnson, Christopher D.

The dynamics of solid oxide fuel cell (SOFC) operation have been considered previously, but mainly through the use of one-dimensional codes applied to co-flow fuel cell systems. In this paper several geometries are considered, including cross-flow, co-flow, and counter-flow. The details of the model are provided, and the model is compared with some initial experimental data. For parameters typical of SOFC operation, a variety of transient cases are investigated, including representative load increase and decrease and system shutdown. Of particular note for large load decrease conditions (e.g., shutdown) is the occurrence of reverse current over significant portions of the cell, starting from the moment of load loss up to the point where equilibrated conditions again provide positive current. Consideration is given as to when such reverse current conditions might most significantly impact the reliability of the cell.

Primordial black holes in linear and non-linear regimes

Energy Technology Data Exchange (ETDEWEB)

Allahyari, Alireza; Abolhasani, Ali Akbar [Department of Physics, Sharif University of Technology, Tehran (Iran, Islamic Republic of); Firouzjaee, Javad T., E-mail: allahyari@physics.sharif.edu, E-mail: j.taghizadeh.f@ipm.ir [School of Astronomy, Institute for Research in Fundamental Sciences (IPM), P.O. Box 19395-5531, Tehran (Iran, Islamic Republic of)

2017-06-01

We revisit the formation of primordial black holes (PBHs) in the radiation-dominated era for both linear and non-linear regimes, elaborating on the concept of an apparent horizon. Contrary to the expectation from vacuum models, we argue that in a cosmological setting a density fluctuation with a high density does not always collapse to a black hole. To this end, we first elaborate on the perturbation theory for spherically symmetric space times in the linear regime. Thereby, we introduce two gauges. This allows to introduce a well defined gauge-invariant quantity for the expansion of null geodesics. Using this quantity, we argue that PBHs do not form in the linear regime irrespective of the density of the background. Finally, we consider the formation of PBHs in non-linear regimes, adopting the spherical collapse picture. In this picture, over-densities are modeled by closed FRW models in the radiation-dominated era. The difference of our approach is that we start by finding an exact solution for a closed radiation-dominated universe. This yields exact results for turn-around time and radius. It is important that we take the initial conditions from the linear perturbation theory. Additionally, instead of using uniform Hubble gauge condition, both density and velocity perturbations are admitted in this approach. Thereby, the matching condition will impose an important constraint on the initial velocity perturbations δ {sup h} {sub 0} = −δ{sub 0}/2. This can be extended to higher orders. Using this constraint, we find that the apparent horizon of a PBH forms when δ > 3 at turn-around time. The corrections also appear from the third order. Moreover, a PBH forms when its apparent horizon is outside the sound horizon at the re-entry time. Applying this condition, we infer that the threshold value of the density perturbations at horizon re-entry should be larger than δ {sub th} > 0.7.

Capacity of Fading Channels in the Low Power Regime

KAUST Repository

Benkhelifa, Fatma

2013-01-01

The low power regime has attracted various researchers in the information theory and communication communities to understand the performance limits of wireless systems. Indeed, the energy consumption is becoming one of the major limiting factors in wireless systems. As such, energy-efficient wireless systems are of major importance to the next generation wireless systems designers. The capacity is a metric that measures the performance limit of a wireless system. The study of the ergodic capacity of some fading channels in the low power regime is the main subject of this thesis. In our study, we consider that the receiver has always a full knowledge of the channel state information. However, we assume that the transmitter has possibly imperfect knowledge of the channel state information, i.e. he knows either perfectly the channel or only an estimated version of the channel. Both radio frequency and free space optical communication channel models are considered. The main contribution of this work is the explicit characterization of how the capacity scales as function of the signal-to-noise ratio in the low power regime. This allows us to characterize the gain due to the perfect knowledge compared to no knowledge of the channel state information at the transmitter. In particular, we show that the gain increases logarithmically for radio frequency communication. However, the gain increases as log2(Pavg) or log4(Pavg) for free-space optical communication, where Pavg is the average power constraint imposed to the input. Furthermore, we characterize the capacity of cascaded fading channels and we applied the result to Rayleigh-product fading channel and to a free-space optical link over gamma-gamma atmospheric turbulence in the presence of pointing errors. Finally, we study the capacity of Nakagami-m fading channel under quality of service constraints, namely the effective capacity. We have shown that the effective capacity converges to Shannon capacity in the very low

Third party nuclear liability regime in the Romanian legislation - current status

International Nuclear Information System (INIS)

Chirica, T.; Chiripus, V.

2004-01-01

The regime of civil liability for nuclear damages in the Romanian legislation is defined by Law no. 703/2001 on civil liability for nuclear damages, as well as Government Decision no. 894/2003 for the approval of the Norms for the enforcement of Law no. 703/2001. These two documents constitute the legal framework that regulates the third party civil liability for nuclear damages. The paper aims at presenting to the audience the main elements of the relatively recent legal framework, namely: the scope of Law no. 703/2001, as well as the subjects to whom such law applies, the regime of civil liability for nuclear damages in Romania (with special emphasis on the relevant responsibilities of nuclear operators), the Romanian nuclear damages compensation system, statute of limitation for claims, types of insurance and financial guarantees covering against civil liability for nuclear damages, limits of nuclear operators' liability, specific requirements regarding the insurance, responsibilities of control and supervision bodies, assessment of nuclear damage.(author)

Regime Switching Vine Copula Models for Global Equity and Volatility Indices

Directory of Open Access Journals (Sweden)

Holger Fink

2017-01-01

Full Text Available For nearly every major stock market there exist equity and implied volatility indices. These play important roles within finance: be it as a benchmark, a measure of general uncertainty or a way of investing or hedging. It is well known in the academic literature that correlations and higher moments between different indices tend to vary in time. However, to the best of our knowledge, no one has yet considered a global setup including both equity and implied volatility indices of various continents, and allowing for a changing dependence structure. We aim to close this gap by applying Markov-switching R-vine models to investigate the existence of different, global dependence regimes. In particular, we identify times of “normal” and “abnormal” states within a data set consisting of North-American, European and Asian indices. Our results confirm the existence of joint points in a time at which global regime switching between two different R-vine structures takes place.

Spatial variations in vegetation as related to the soil moisture regime over an arid limestone hillside, northern Negev, Israel.

Science.gov (United States)

Yair, A; Danin, A

1980-01-01

A detailed study of the distribution of plant communities was conducted in an experimental site, located in the arid northern Negev of Israel, where the spatial variation in rainfall, runoff and soil moisture regime are currently being studied. Phytogeographical methods of analysis usually used for studies on a regional scale were applied for a small area extending over 11,325 m 2 of a north-facing hillside. Data obtained indicate that the best water regime and a high diversity of plant species are characteristic of a massive limestone rock unit; whereas worse water regimes characterize densely jointed and thinly bedded limestones. Over slopes, developed in a uniform lithology, whose lower part is composed of a colluvial mantle, a gradual downslope worsening of the soil moisture regime is recorded within the colluvium. These changes are well expressed in the distribution of the plant communities and their phytogeographical affinities along the slopes.

Human impacts on runoff regime of middle and lower Yellow River

Directory of Open Access Journals (Sweden)

Yan-fang Sang

2011-03-01

Full Text Available In this study, the 54-year (1950 to 2003 monthly runoff series from February, April, August, and November, as well as the annual runoff series, measured at both Huayuankou and Lijin hydrological stations were chosen as representative data, and the continuous wavelet transform (CWT was applied to analyze the impacts of human activities on the runoff regime of the middle and lower Yellow River. A point of change in 1970 was first determined, and the observed series before 1970 were considered natural runoff while those after 1970 were restored according to linear trends. Then, the CWT was applied to both the observed and restored runoff series to reveal their variations at multi-temporal scales, including the five temporal ranges of 1–4, 6–8, 9–12, 16–22, and 22–30 years, and the trend at the temporal scale of 54 years. These analysis results are compared and discussed in detail. In conclusion, because of the impacts of human activities, there have been significant changes in the runoff regime in the middle and lower Yellow River since 1970. The decaying tendency of annual runoff has become more pronounced, and the inner-annual distribution of runoff has changed, but human activities have had little impact on the periodic characteristics of runoff.

Implementing peak load reduction algorithms for household electrical appliances

International Nuclear Information System (INIS)

Dlamini, Ndumiso G.; Cromieres, Fabien

2012-01-01

Considering household appliance automation for reduction of household peak power demand, this study explored aspects of the interaction between household automation technology and human behaviour. Given a programmable household appliance switching system, and user-reported appliance use times, we simulated the load reduction effectiveness of three types of algorithms, which were applied at both the single household level and across all 30 households. All three algorithms effected significant load reductions, while the least-to-highest potential user inconvenience ranking was: coordinating the timing of frequent intermittent loads (algorithm 2); moving period-of-day time-flexible loads to off-peak times (algorithm 1); and applying short-term time delays to avoid high peaks (algorithm 3) (least accommodating). Peak reduction was facilitated by load interruptibility, time of use flexibility and the willingness of users to forgo impulsive appliance use. We conclude that a general factor determining the ability to shift the load due to a particular appliance is the time-buffering between the service delivered and the power demand of an appliance. Time-buffering can be ‘technologically inherent’, due to human habits, or realised by managing user expectations. There are implications for the design of appliances and home automation systems. - Highlights: ► We explored the interaction between appliance automation and human behaviour. ► There is potential for considerable load shifting of household appliances. ► Load shifting for load reduction is eased with increased time buffering. ► Design, human habits and user expectations all influence time buffering. ► Certain automation and appliance design features can facilitate load shifting.

Endogenous Monetary Policy Regime Change

OpenAIRE

Troy Davig; Eric M. Leeper

2006-01-01

This paper makes changes in monetary policy rules (or regimes) endogenous. Changes are triggered when certain endogenous variables cross specified thresholds. Rational expectations equilibria are examined in three models of threshold switching to illustrate that (i) expectations formation effects generated by the possibility of regime change can be quantitatively important; (ii) symmetric shocks can have asymmetric effects; (iii) endogenous switching is a natural way to formally model preempt...

Application of PSAT to Load Flow Analysis with STATCOM under Load Increase Scenario and Line Contingencies

Science.gov (United States)

Telang, Aparna S.; Bedekar, P. P.

2017-09-01

Load flow analysis is the initial and essential step for any power system computation. It is required for choosing better options for power system expansion to meet with ever increasing load demand. Implementation of Flexible AC Transmission System (FACTS) device like STATCOM, in the load flow, which is having fast and very flexible control, is one of the important tasks for power system researchers. This paper presents a simple and systematic approach for steady state power flow calculations with FACTS controller, static synchronous compensator (STATCOM) using command line usage of MATLAB tool-power system analysis toolbox (PSAT). The complexity of MATLAB language programming increases due to incorporation of STATCOM in an existing Newton-Raphson load flow algorithm. Thus, the main contribution of this paper is to show how command line usage of user friendly MATLAB tool, PSAT, can extensively be used for quicker and wider interpretation of the results of load flow with STATCOM. The novelty of this paper lies in the method of applying the load increase pattern, where the active and reactive loads have been changed simultaneously at all the load buses under consideration for creating stressed conditions for load flow analysis with STATCOM. The performance have been evaluated on many standard IEEE test systems and the results for standard IEEE-30 bus system, IEEE-57 bus system, and IEEE-118 bus system are presented.

Evaluation of constraint methodologies applied to a shallow-flaw cruciform bend specimen tested under biaxial loading conditions

International Nuclear Information System (INIS)

Bass, B.R.; McAfee, W.J.; Williams, P.T.; Pennell, W.E.

1998-01-01

A technology to determine shallow-flaw fracture toughness of reactor pressure vessel (RPV) steels is being developed for application to the safety assessment of RPVs containing postulated shallow surface flaws. Matrices of cruciform beam tests were developed to investigate and quantify the effects of temperature, biaxial loading, and specimen size on fracture initiation toughness of two-dimensional (constant depth), shallow surface flaws. The cruciform beam specimens were developed at Oak Ridge National Laboratory (ORNL) to introduce a prototypic, far-field. out-of-plane biaxial stress component in the test section that approximates the nonlinear stresses resulting from pressurized-thermal-shock or pressure-temperature loading of an RPV. Tests were conducted under biaxial load ratios ranging from uniaxial to equibiaxial. These tests demonstrated that biaxial loading can have a pronounced effect on shallow-flaw fracture toughness in the lower transition temperature region for RPV materials. The cruciform fracture toughness data were used to evaluate fracture methodologies for predicting the observed effects of biaxial loading on shallow-flaw fracture toughness. Initial emphasis was placed on assessment of stress-based methodologies. namely, the J-Q formulation, the Dodds-Anderson toughness scaling model, and the Weibull approach. Applications of these methodologies based on the hydrostatic stress fracture criterion indicated an effect of loading-biaxiality on fracture toughness, the conventional maximum principal stress criterion indicated no effect

Enhanced sensitivity fibre Bragg grating (FBG) load sensor

International Nuclear Information System (INIS)

Correia, Ricardo; Chehura, Edmon; Li, Jin; James, Stephen W; Tatam, Ralph P

2010-01-01

The characterization of a load sensor based on the transverse loading of a subsection of a fibre Bragg grating (FBG) embedded within a cube of epoxy resin is presented. When the epoxy resin cube is loaded transverse to the axis of the fibre, its deformation transduces the load to a strain along the axis of the optical fibre, which changes the period of the embedded section of the FBG. This creates a spectral dropout within the bandwidth of the FBG, with an absolute wavelength that is linearly dependent on the applied load. This technique enhances the sensitivity of the FBG to transverse loading by a factor of 15, to 2.9 × 10 −2 ± 0.01 nm N −1 , when compared to the direct transverse loading of a bare fibre, and also protects the fibre from mechanical damage at the loading point

Microwave heating device for internal heating convection experiments, applied to Earth's mantle dynamics.

Science.gov (United States)

Surducan, E; Surducan, V; Limare, A; Neamtu, C; Di Giuseppe, E

2014-12-01

We report the design, construction, and performances of a microwave (MW) heating device for laboratory experiments with non-contact, homogeneous internal heating. The device generates MW radiation at 2.47 GHz from a commercial magnetron supplied by a pulsed current inverter using proprietary, feedback based command and control hardware and software. Specially designed MW launchers direct the MW radiation into the sample through a MW homogenizer, devised to even the MW power distribution into the sample's volume. An adjustable MW circuit adapts the MW generator to the load (i.e., the sample) placed in the experiment chamber. Dedicated heatsinks maintain the MW circuits at constant temperature throughout the experiment. Openings for laser scanning for image acquisition with a CCD camera and for the cooling circuits are protected by special MW filters. The performances of the device are analyzed in terms of heating uniformity, long term output power stability, and load matching. The device is used for small scale experiments simulating Earth's mantle convection. The 30 × 30 × 5 cm(3) convection tank is filled with a water‑based viscous fluid. A uniform and constant temperature is maintained at the upper boundary by an aluminum heat exchanger and adiabatic conditions apply at the tank base. We characterize the geometry of the convective regime as well as its bulk thermal evolution by measuring the velocity field by Particle Image Velocimetry and the temperature field by using Thermochromic Liquid Crystals.

LCF life prediction for waspaloy in the creep-fatigue interaction regime

International Nuclear Information System (INIS)

Yeom, Jong Taek; Park, Nho Kwang

2001-01-01

This paper describes the empirical rule of strain rate modified linear accumulation of creep damage(SRM rule) for Low-Cycle Fatigue(LCF) life prediction of Waspaloy in the creep-fatigue interaction regime and Chaboche type unified viscoplastic model predicting the stress-strain response in various cyclic loading conditions. The comparison of the experimental data and the predictions for strain controlled LCF tests carried out for various strain ranges at 600 .deg. C and 650 .deg. C was made. Chaboche type unified viscoplastic model described efficiently the inelastic deformation behavior during LCF tests. Crack-initiation lifting method to predict the material life was investigated with Strain Rate Modification(SRM) rule. The application of SRM rule to LCF tests on Waspaloy indicated a good agreement between measured and predicted cycles to failure

Statistics of exchange rate regimes in Nigeria | Iwueze | Global ...

African Journals Online (AJOL)

The three distinct exchange rate regimes of Nigeria were subjected to Autoregressive Integrated Moving Average (ARIMA) modeling in order to compare them with respect to model structure. It was found that the three regimes admit different models. Regime one admits Moving average model of order 2, Regime two admits ...

New trends of activity on supporting of non-proliferation regime

International Nuclear Information System (INIS)

Issaeva, G.M.; Tyupkina, O.G.

2002-01-01

Taking into account the necessity of all possible strengthening of non-proliferation regimes Kazakhstan participates in a number of agreements and associations: Nuclear Non-proliferation Treaty, Comprehensive Test-Ban-Treaty, International Atomic Energy Agency, Nuclear Supplier Group, Missile Technology Control Regime, Conference on Disarmament, etc. The Cooperative Threat Reduction Program (CTR) greatly influenced on the development on non-proliferation regime in Kazakhstan. During initial stage of CTR activity (1993-1995) military projects prevailed. Later (1995-1997) the projects on liquidation of infrastructure for nuclear and bio- weapons were successfully realized. Last years, since 1999, the attention was shifted towards proliferation prevention of hazardous nuclear and biological materials. Recent terrorist acts and world community activity on global safety strengthening underline an urgency of quite new problems that entirely applied to Kazakhstan: monitoring of hazardous materials; enhancement of safety systems of 'risky' facilities and technologies; creation and/or upgrading of safety systems for industry infrastructure. The proposals of these new trends of non-proliferation have been developed. Development of physical protection system for oil and gas industry infrastructure of Kazakhstan based on safety concepts of nuclear facilities; Evaluation of radionuclide contamination and safety of oil and gas facilities of the Caspian region; Counteraction to nuclear materials proliferation; Cooperative approaches in preventing/reducing of illicit trafficking and use of WMD-related explosive materials. Implementation of the project would make of substantial contribution to successful solution of either regional or global safety problem

Elasto-plastic behavior of pipe subjected to steady axial load and cyclic bending

International Nuclear Information System (INIS)

Yao Yanping; Lu Mingwan; Zhang Xiong

2004-01-01

The elasto-plastic behavior of a pipe subjected to a steady axial force and a cyclic bending moment is studied. By using two parameters c and d, which describe the elasto-plastic interfaces of beam cross-section, the boundary curve equations between various types of elasto-plastic behavior, such as shakedown, plastic fatigue, ratcheting, and plastic collapse, are derived. The results are applicable for beams of any cross-section with two orthogonal axes of symmetry. As a result, the load regime diagram for a pipe is obtained, which gives an intuitive picture of the elasto-plastic behavior of the pipe under a given combination of constant axial load and cyclic bending moment

Choice of exchange rate regimes for African countries: Fixed or Flexible Exchange rate regimes?

OpenAIRE

Simwaka, Kisu

2010-01-01

The choice of an appropriate exchange rate regime has been a subject of ongoing debate in international economics. The majority of African countries are small open economies and thus where the choice of the exchange rate regime is an important policy issue. Aside from factors such as interest rates and inflation, the exchange rate is one of the most important determinants of a country’s relative level of economic health. For this reason, exchange rates are among the most watched analyzed and ...

Estimation of dynamic rotor loads for the rotor systems research aircraft: Methodology development and validation

Science.gov (United States)

Duval, R. W.; Bahrami, M.

1985-01-01

The Rotor Systems Research Aircraft uses load cells to isolate the rotor/transmission systm from the fuselage. A mathematical model relating applied rotor loads and inertial loads of the rotor/transmission system to the load cell response is required to allow the load cells to be used to estimate rotor loads from flight data. Such a model is derived analytically by applying a force and moment balance to the isolated rotor/transmission system. The model is tested by comparing its estimated values of applied rotor loads with measured values obtained from a ground based shake test. Discrepancies in the comparison are used to isolate sources of unmodeled external loads. Once the structure of the mathematical model has been validated by comparison with experimental data, the parameters must be identified. Since the parameters may vary with flight condition it is desirable to identify the parameters directly from the flight data. A Maximum Likelihood identification algorithm is derived for this purpose and tested using a computer simulation of load cell data. The identification is found to converge within 10 samples. The rapid convergence facilitates tracking of time varying parameters of the load cell model in flight.

A Novel Load Capacity Model with a Tunable Proportion of Load Redistribution against Cascading Failures

Directory of Open Access Journals (Sweden)

Zhen-Hao Zhang

2018-01-01

Full Text Available Defence against cascading failures is of great theoretical and practical significance. A novel load capacity model with a tunable proportion is proposed. We take degree and clustering coefficient into account to redistribute the loads of broken nodes. The redistribution is local, where the loads of broken nodes are allocated to their nearest neighbours. Our model has been applied on artificial networks as well as two real networks. Simulation results show that networks get more vulnerable and sensitive to intentional attacks along with the decrease of average degree. In addition, the critical threshold from collapse to intact states is affected by the tunable parameter. We can adjust the tunable parameter to get the optimal critical threshold and make the systems more robust against cascading failures.

Eccentric exercise: mechanisms and effects when used as training regime or training adjunct.

Science.gov (United States)

Vogt, Michael; Hoppeler, Hans H

2014-06-01

The aim of the current review is to discuss applications and mechanism of eccentric exercise in training regimes of competitive sports. Eccentric muscle work is important in most sports. Eccentric muscle contractions enhance the performance during the concentric phase of stretch-shortening cycles, which is important in disciplines like sprinting, jumping, throwing, and running. Muscles activated during lengthening movements can also function as shock absorbers, to decelerate during landing tasks or to precisely deal with high external loading in sports like alpine skiing. The few studies available on trained subjects reveal that eccentric training can further enhance maximal muscle strength and power. It can further optimize muscle length for maximal tension development at a greater degree of extension, and has potential to improve muscle coordination during eccentric tasks. In skeletal muscles, these functional adaptations are based on increases in muscle mass, fascicle length, number of sarcomeres, and cross-sectional area of type II fibers. Identified modalities for eccentric loading in athletic populations involve classical isotonic exercises, accentuated jumping exercises, eccentric overloading exercises, and eccentric cycle ergometry. We conclude that eccentric exercise offers a promising training modality to enhance performance and to prevent injuries in athletes. However, further research is necessary to better understand how the neuromuscular system adapts to eccentric loading in athletes. Copyright © 2014 the American Physiological Society.

Capacitance densitometer for flow regime identification

International Nuclear Information System (INIS)

Shipp, R.L. Jr.

1978-01-01

This invention relates to a capacitance densitometer for determining the flow regime of a two-phase flow system. A two-element capacitance densitometer is used in conjunction with a conventional single-beam gamma densitometer to unambiguously identify the prevailing flow regime and the average density of a flowing fluid

Multiscale regime shifts and planetary boundaries

NARCIS (Netherlands)

Hughes, T.P.; Carpenter, S.; Rockstrom, J.; Scheffer, M.; Walker, B.

2013-01-01

Life on Earth has repeatedly displayed abrupt and massive changes in the past, and there is no reason to expect that comparable planetary-scale regime shifts will not continue in the future. Different lines of evidence indicate that regime shifts occur when the climate or biosphere transgresses a

Short-range wakefields generated in the blowout regime of plasma-wakefield acceleration

Science.gov (United States)

Stupakov, G.

2018-04-01

In the past, calculation of wakefields generated by an electron bunch propagating in a plasma has been carried out in linear approximation, where the plasma perturbation can be assumed small and plasma equations of motion linearized. This approximation breaks down in the blowout regime where a high-density electron driver expels plasma electrons from its path and creates a cavity void of electrons in its wake. In this paper, we develop a technique that allows us to calculate short-range longitudinal and transverse wakes generated by a witness bunch being accelerated inside the cavity. Our results can be used for studies of the beam loading and the hosing instability of the witness bunch in plasma-wakefield and laser-wakefield acceleration.

Bed Load Variability and Morphology of Gravel Bed Rivers Subject to Unsteady Flow: A Laboratory Investigation

Science.gov (United States)

Redolfi, M.; Bertoldi, W.; Tubino, M.; Welber, M.

2018-02-01

Measurement and estimation of bed load transport in gravel bed rivers are highly affected by its temporal fluctuations. Such variability is primarily driven by the flow regime but is also associated with a variety of inherent channel processes, such as flow turbulence, grain entrainment, and bed forms migration. These internal and external controls often act at comparable time scales, and are therefore difficult to disentangle, thus hindering the study of bed load variability under unsteady flow regime. In this paper, we report on laboratory experiments performed in a large, mobile bed flume where typical hydromorphological conditions of gravel bed rivers were reproduced. Data from a large number of replicated runs, including triangular and square-wave hydrographs, were used to build a statistically sound description of sediment transport processes. We found that the inherent variability of bed load flux strongly depends on the sampling interval, and it is significantly higher in complex, wandering or braided channels. This variability can be filtered out by computing the mean response over the experimental replicates, which allows us to highlight two distinctive phenomena: (i) an overshooting (undershooting) response of the mean bed load flux to a sudden increase (decrease) of discharge, and (ii) a clockwise hysteresis in the sediment rating curve. We then provide an interpretation of these findings through a conceptual mathematical model, showing how both phenomena are associated with a lagging morphological adaptation to unsteady flow. Overall, this work provides basic information for evaluating, monitoring, and managing gravel transport in morphologically active rivers.

Holomorphic Embedded Load Flow for Autonomous Spacecraft Power Systems, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — The proposed innovation advances the ability to apply the Holomorphic Embedding Load Flow Technology (HELM™) method to provide deterministic load flow modeling for...

Precast concrete sandwich panels subjected to impact loading

Science.gov (United States)

Runge, Matthew W.

Precast concrete sandwich panels are a relatively new product in the construction industry. The design of these panels incorporates properties that allow for great resilience against temperature fluctuation as well as the very rapid and precise construction of facilities. The concrete sandwich panels investigated in this study represent the second generation of an ongoing research and development project. This second generation of panels have been engineered to construct midsized commercial buildings up to three stories in height as well as residential dwellings. The panels consist of a double-tee structural wythe, a foam core and a fascia wythe, joined by shear connectors. Structures constructed from these panels may be subjected to extreme loading including the effects of seismic and blast loading in addition to wind. The aim of this work was to investigate the behaviour of this particular sandwich panel when subjected to structural impact events. The experimental program consisted of fourteen concrete sandwich panels, five of which were considered full-sized specimens (2700 mm X 1200mm X 270 mm) and nine half-sized specimens (2700mm X 600mm X 270 mm) The panels were subjected to impact loads from a pendulum impact hammer where the total energy applied to the panels was varied by changing the mass of the hammer. The applied loads, displacements, accelerations, and strains at the mid-span of the panel as well as the reaction point forces were monitored during the impact. The behaviour of the panels was determined primarily from the experimental results. The applied loads at low energy levels that caused little to no residual deflection as well as the applied loads at high energy levels that represent catastrophic events and thus caused immediate failure were determined from an impact on the structural and the fascia wythes. Applied loads at intermediate energy levels representing extreme events were also used to determine whether or not the panels could withstand

Current US nuclear liability regime

International Nuclear Information System (INIS)

Brown, O.F.

2000-01-01

The Price-Anderson Act Adopted by US Congress in 1957 as the world's first national nuclear liability regime. It is a comprehensive, complicated and unique system and stems from special features of US legal regime and federal system of government. It differs from other systems by providing for 'economic', not legal; channeling of liability to facility operator and not recommended as model for other states, but most features adopted by other states and international conventions

Level-ARCH Short Rate Models with Regime Switching

DEFF Research Database (Denmark)

Christiansen, Charlotte

This paper introduces regime switching volatility into level- ARCH models for the short rates of the US, the UK, and Germany. Once regime switching and level effects are included there are no gains from including ARCH effects. It is of secondary importance exactly how the regime switching is spec...

How Welfare Regimes Generate and Erode Social Capital

DEFF Research Database (Denmark)

Larsen, Christian Albrekt

2007-01-01

in the USA and other liberal welfare regimes, while social capital is stable in the so-called social democratic and conservative welfare regimes. The second puzzle is why the group of social democratic regimes have extremely high levels of social trust. It is argued that both puzzles have to do......Comparative studies of social capital, operationalised as social trust between citizens, have revealed two major puzzles. The first puzzle has to do with the decline in social trust in the USA, which fuelled considerable debate about social capital. The question is why social capital erodes...... with the presence or absence of a poor and culturally distinct underclass. The social democratic welfare regimes hinder – while the liberal welfare regime generate – such underclass phenomena....

Estimating Dynamic Connectivity States in fMRI Using Regime-Switching Factor Models

KAUST Repository

Ting, Chee-Ming

2017-12-06

We consider the challenges in estimating state-related changes in brain connectivity networks with a large number of nodes. Existing studies use sliding-window analysis or time-varying coefficient models which are unable to capture both smooth and abrupt changes simultaneously, and rely on ad-hoc approaches to the high-dimensional estimation. To overcome these limitations, we propose a Markov-switching dynamic factor model which allows the dynamic connectivity states in functional magnetic resonance imaging (fMRI) data to be driven by lower-dimensional latent factors. We specify a regime-switching vector autoregressive (SVAR) factor process to quantity the time-varying directed connectivity. The model enables a reliable, data-adaptive estimation of change-points of connectivity regimes and the massive dependencies associated with each regime. We develop a three-step estimation procedure: 1) extracting the factors using principal component analysis, 2) identifying connectivity regimes in a low-dimensional subspace based on the factor-based SVAR model, 3) constructing high-dimensional state connectivity metrics based on the subspace estimates. Simulation results show that our estimator outperforms K-means clustering of time-windowed coefficients, providing more accurate estimate of time-evolving connectivity. It achieves percentage of reduction in mean squared error by 60% when the network dimension is comparable to the sample size. When applied to resting-state fMRI data, our method successfully identifies modular organization in resting-state networks in consistency with other studies. It further reveals changes in brain states with variations across subjects and distinct large-scale directed connectivity patterns across states.

Can Old Regimes Handle New Wars?

DEFF Research Database (Denmark)

Henningsen, Troels

Research on New Wars argues that since the 1980s states and regimes have become more vulnerable to violence from non-state actors. Two developments in the Sahel region support the New Wars thesis: an increase in Islamist radicalization and new access to the global black market, both of which......, the paper finds that regimes in the Sahel region are still able to cope with the rise in non-state threats. The paper first shortly compares the longevity of the present regimes in the Sahel region to all previous ones, second examines in-depth how Chad and Mali fight the insurgents. Findings are that since...

FEL in transverse optical klystron regime

International Nuclear Information System (INIS)

Scarlat, F.; Baltateanu, N.

1994-01-01

Among all operational regimes of free electron laser (FEL), the transverse optical regime (TOK) requires the least stringent electron beam parameters. The device associated to this regime, also defined as FEL with two or more components, consists of two or more identical interaction sections separated by one or more drift distances among themselves. Starting from the motion equations which describe the interaction between an electron and the radiation inside the undulator, one can obtain some practical expressions for the calculation of the efficiency of the energy transfer from the electron to the radiation, and the gain of the external coherent radiation for a FEL in TOK with three cavities. (Author)

Grid faults' impact on wind turbine structural loads

DEFF Research Database (Denmark)

Hansen, Anca Daniela; Cutululis, Nicolaos Antonio; Iov, F.

2007-01-01

The objective of this work is to illustrate the impact of the grid faults on the wind turbine structural loads. Grid faults are typically simulated in detailed power system simulation tools, which by applying simplified mechanical models, are not able to provide a throughout insight...... on the structural loads caused by sudden disturbances on the grid. On the other hand, structural loads of the wind turbine are typically assessed in advanced aerolastic computer codes, which by applying simplified electrical models do not provide detailed electrical insight. This paper presents a simulation...... strategy, where the focus is on how to access a proper combination of two complimentary simulations tools, such as the advanced aeroelastic computer code HAWC2 and the detailed power system simulation tool DIgSILENT, in order to provide a whole overview of both the structural and the electrical behaviour...

The effect of normal load on polytetrafluoroethylene tribology.

Science.gov (United States)

Barry, Peter R; Chiu, Patrick Y; Perry, Scott S; Sawyer, W Gregory; Phillpot, Simon R; Sinnott, Susan B

2009-04-08

The tribological behavior of oriented poly(tetrafluoroethylene) (PTFE) sliding surfaces is examined as a function of sliding direction and applied normal load in classical molecular dynamics (MD) simulations. The forces are calculated with the second-generation reactive empirical bond-order potential for short-range interactions, and with a Lennard-Jones potential for long-range interactions. The range of applied normal loads considered is 5-30 nN. The displacement of interfacial atoms from their initial positions during sliding is found to vary by a factor of seven, depending on the relative orientation of the sliding chains. However, within each sliding configuration the magnitude of the interfacial atomic displacements exhibits little dependence on load over the range considered. The predicted friction coefficients are also found to vary with chain orientation and are in excellent quantitative agreement with experimental measurements.

Investigation of flow regime in debris bed formation behavior with nonspherical particles

Directory of Open Access Journals (Sweden)

Songbai Cheng

2018-02-01

Full Text Available It is important to clarify the characteristics of flow regimes underlying the debris bed formation behavior that might be encountered in core disruptive accidents of sodium-cooled fast reactors. Although in our previous publications, by applying dimensional analysis technique, an empirical model, with its reasonability confirmed over a variety of parametric conditions, has been successfully developed to predict the regime transition and final bed geometry formed, so far this model is restricted to predictions of debris mixtures composed of spherical particles. Focusing on this aspect, in this study a new series of experiments using nonspherical particles have been conducted. Based on the knowledge and data obtained, an extension scheme is suggested with the purpose of extending the base model to cover the particle-shape influence. Through detailed analyses and given our current range of experimental conditions, it is found that, by coupling the base model with this scheme, respectable agreement between experiments and model predictions for the regime transition can be achieved for both spherical and nonspherical particles. Knowledge and evidence from our work might be utilized for the future improvement of design of an in-vessel core catcher as well as the development and verification of sodium-cooled fast reactor severe accident analysis codes in China.

Evaluating trophic cascades as drivers of regime shifts in different ocean ecosystems

Science.gov (United States)

Pershing, Andrew J.; Mills, Katherine E.; Record, Nicholas R.; Stamieszkin, Karen; Wurtzell, Katharine V.; Byron, Carrie J.; Fitzpatrick, Dominic; Golet, Walter J.; Koob, Elise

2015-01-01

In ecosystems that are strongly structured by predation, reducing top predator abundance can alter several lower trophic levels—a process known as a trophic cascade. A persistent trophic cascade also fits the definition of a regime shift. Such ‘trophic cascade regime shifts' have been reported in a few pelagic marine systems—notably the Black Sea, Baltic Sea and eastern Scotian Shelf—raising the question of how common this phenomenon is in the marine environment. We provide a general methodology for distinguishing top-down and bottom-up effects and apply this methodology to time series from these three ecosystems. We found evidence for top-down forcing in the Black Sea due primarily to gelatinous zooplankton. Changes in the Baltic Sea are primarily bottom-up, strongly structured by salinity, but top-down forcing related to changes in cod abundance also shapes the ecosystem. Changes in the eastern Scotian Shelf that were originally attributed to declines in groundfish are better explained by changes in stratification. Our review suggests that trophic cascade regime shifts are rare in open ocean ecosystems and that their likelihood increases as the residence time of water in the system increases. Our work challenges the assumption that negative correlation between consecutive trophic levels implies top-down forcing.

Fuel element cladding state change mathematical model for a WWER-1000 plant operated in the mode of varying loading

Directory of Open Access Journals (Sweden)

S. N. Pelykh

2010-09-01

Full Text Available Main features of a fuel element cladding state change mathematical model for a WWER-1000 reactor plant operated in the mode of varying loading are listed. The integrated model is based on the energy creep theory, uses the finite element method for imultaneous solution of the fuel element heat conduction and mechanical deformation equa-tions. Proposed mathematical model allows us to determine the influence of the WWER-1000 regime parameters and fuel assembly design characteristics on the change of cladding properties under different loading conditions of normal operation, as well as the cladding limiting state at variable loading depending on the length, depth and number of cycles.

The role of the media in establishing international security regimes

Directory of Open Access Journals (Sweden)

Chanan Naveh

2005-04-01

Full Text Available This article focuses primarily on the media's impact on international security regimes. It explores the ways in which the media affect the lifecycles of international regimes, from the time they are first conceived of, through their establishment, consolidation and stabilization, up until their ultimate demise. Although this paper highlights the media's role in the evolution of security regimes, it is clear that, regardless of the regime in question, media play a role throughout the lifecycle of all international regimes, whatever their character. In order to analyze the relationships of the media with security regimes in general, and specifically their contribution to each stage in their development, the article utilizes methodologies from the field of communication studies. It examines the media's agenda, "news values" and various functions, and their ability to mobilize public support for the particular issue of the regime. To date, most studies have explored the interaction between media communication patterns and global developments at the state level, or in relation to the formulation of foreign policy, while largely ignoring the international dimension of the relationship. This article attempts to remedy this situation, and the relevant processes are analysed in a case study of the anti-Iraq international security regime. It should be noted that although the paper focuses on the specific anti-Iraqi regime, it is part of a more general Anti-Rogue actors regime which includes the war against global terrorism. The study of the development of the anti-Iraq press-security regime teaches us that during international crises the media mobilize and unanimously support the regime fighting the "bad guys." But, when the regime develops and enters disputed turfs and begins to lose its legitimacy, media support diminishes, and the media may even develop into an opposing force and may join the actors fighting against this regime. Moreover, the study of

Regimes of mini black hole abandoned to accretion

Science.gov (United States)

Paik, Biplab

2018-01-01

Being inspired by the Eddington’s idea, along with other auxiliary arguments, it is unveiled that there exist regimes of a black hole that would prohibit accretion of ordinary energy. In explicit words, there exists a lower bound to black hole mass below which matter accretion process does not run for black holes. Not merely the baryonic matter, but, in regimes, also the massless photons could get prohibited from rushing into a black hole. However, unlike the baryon accretion abandoned black hole regime, the mass-regime of a black hole prohibiting accretion of radiation could vary along with its ambient temperature. For example, we discuss that earlier to 10‑8 s after the big-bang, as the cosmological temperature of the Universe grew above ˜ 1014 K, the mass range of black hole designating the radiation accretion abandoned regime, had to be in varying state being connected with the instantaneous age of the evolving Universe by an “one half” power law. It happens to be a fact that a black hole holding regimes prohibiting accretion of energy is gigantic by its size in comparison to the Planck length-scale. Hence the emergence of these regimes demands mini black holes for not being viable as profound suckers of energy. Consideration of accretion abandoned regimes could be crucial for constraining or judging the evolution of primordial black holes over the age of the Universe.

Statistical estimation of loads from gas explosions

Energy Technology Data Exchange (ETDEWEB)

Hoeiset, Stian

1998-12-31

In the design of structures in the offshore and process industries, the possibility of a gas explosion must always be considered. The main uncertainties in computerized simulation of gas explosions are the assumptions of the gas cloud, the location of the ignition point and the properties of the simulator itself. This thesis quantifies the levels of these uncertainties by performing a large number of simulations on three offshore modules and one onshore plant. It is found that (1) there is an approximate linear relation between pressure and gas volume, (2) it may be possible to find a linear relation between pressure and impulse, (3) there is an inverse relation between pressure and duration, (4) the response of offshore structures exposed to gas explosions are rarely in the impulsive regime, (5) loading rates vary widely in magnitude, (6) an assumption of a triangular explosion pulse is often correct, (7) louvres increase pressure, impulse and duration of an explosion. The effect of ignition point location is studied in detail. It is possible to derive an ignition point uncertainty load factor that shows predictable behaviour by generalizing the non-parametric properties of the explosion pressure. A model for taking into account the uncertainties regarding gas volume, ignition point location and simulator imperfectness is proposed. The model is intended to produce a characteristic load for structural design. 68 refs., 51 figs., 36 tabs.

The effect of loading rate on pile bearing capacity of saturated sand

NARCIS (Netherlands)

Archeewa, E.

2005-01-01

Pile load tests are commonly used by engineers to determine its bearing capacity. At present, there are three methods of pile load tests: the static, the dynamic and the quasi-static test. The static pile load test is done by applying an axial load on the pile with a long duration. The dynamic and

A Dynamic Model for Load Balancing in Cloud Infrastructure

Directory of Open Access Journals (Sweden)

Jitendra Bhagwandas Bhatia

2015-08-01

Full Text Available This paper analysis various challenges faced in optimizing computing resource utilization via load balancing and presents a platform-independent model for load balancing which targets high availability of resources, low SLA (Service Level agreement violations and saves power. To achieve this, incoming requests are monitored for sudden burst, a prediction model is employed to maintain high availability and a power-aware algorithm is applied for choosing a suitable physical node for a virtual host. The proposed dynamic load balancing model provides a way to conflicting goals of saving power and maintaining high resource availability.For anyone building a private, public or hybrid IaaS cloud infrastructure, load balancing of virtual hosts on a limited number of physical nodes, becomes a crucial aspect. This paper analysis various challenges faced in optimizing computing resource utilization via load balancing and presents a platform independent model for load balancing which targets high availability of resources, low SLA (Service Level agreement violations and saves power. To achieve this, incoming requests are monitored for sudden burst, prediction model is employed to maintain high availability and power aware algorithm is applied for choosing a suitable physical node for virtual host. The proposed dynamic load balancing model provides a way to conflicting goals of saving power and maintaining high resource availability.

TARIFFS AND REGIMES OF POWER CONSUMPTION

Directory of Open Access Journals (Sweden)

S. V. Batsova

2010-01-01

Full Text Available Analysis of regimes of electro-consumption at RUP «BMZ» is carried out. It is shown that in conditions of rapid growth of prices for electric power one of the conditions of reduction of production expenses is to be the increase of efficiency of the electro-consumption regimes control.

A review of the wind loading zones for flat roofs in code provisions

NARCIS (Netherlands)

Geurts, C.P.W.; Kopp, G.A.; Morrison, M.J.

2013-01-01

The provisions for wind loads on flat roofs differ considerably between current wind loading standards in different jurisdictions. For a number of major wind loading codes, both the definition of roof zones, and the values applied to determine the wind loads are discussed. This paper concentrates on

In Situ Test Study of Characteristics of Coal Mining Dynamic Load

Directory of Open Access Journals (Sweden)

Jiang He

2015-01-01

Full Text Available Combination of coal mining dynamic load and high static stress can easily induce such dynamic disasters as rock burst, coal and gas outburst, roof fall, and water inrush. In order to obtain the characteristic parameters of mining dynamic load and dynamic mechanism of coal and rock, the stress wave theory is applied to derive the relation of mining dynamic load strain rate and stress wave parameters. The in situ test was applied to study the stress wave propagation law of coal mine dynamic load by using the SOS microseismic monitoring system. An evaluation method for mining dynamic load strain rate was proposed, and the statistical evaluation was carried out for the range of strain rate. The research results show that the loading strain rate of mining dynamic load is in direct proportion to the seismic frequency of coal-rock mass and particle peak vibration velocity and is in inverse proportion to wave velocity. The high-frequency component damps faster than the low-frequency component in the shockwave propagating process; and the peak particle vibration velocity has a power functional relationship with the transmitting distance. The loading strain rate of mining dynamic load is generally less than class 10−1/s.

A coupled diffusion-fluid pressure model to predict cell density distribution for cells encapsulated in a porous hydrogel scaffold under mechanical loading.

Science.gov (United States)

Zhao, Feihu; Vaughan, Ted J; Mc Garrigle, Myles J; McNamara, Laoise M

2017-10-01

Tissue formation within tissue engineering (TE) scaffolds is preceded by growth of the cells throughout the scaffold volume and attachment of cells to the scaffold substrate. It is known that mechanical stimulation, in the form of fluid perfusion or mechanical strain, enhances cell differentiation and overall tissue formation. However, due to the complex multi-physics environment of cells within TE scaffolds, cell transport under mechanical stimulation is not fully understood. Therefore, in this study, we have developed a coupled multiphysics model to predict cell density distribution in a TE scaffold. In this model, cell transport is modelled as a thermal conduction process, which is driven by the pore fluid pressure under applied loading. As a case study, the model is investigated to predict the cell density patterns of pre-osteoblasts MC3T3-e1 cells under a range of different loading regimes, to obtain an understanding of desirable mechanical stimulation that will enhance cell density distribution within TE scaffolds. The results of this study have demonstrated that fluid perfusion can result in a higher cell density in the scaffold region closed to the outlet, while cell density distribution under mechanical compression was similar with static condition. More importantly, the study provides a novel computational approach to predict cell distribution in TE scaffolds under mechanical loading. Copyright © 2017 Elsevier Ltd. All rights reserved.

Loads and loads and loads: the influence of prospective load, retrospective load, and ongoing task load in prospective memory

Science.gov (United States)

Meier, Beat; Zimmermann, Thomas D.

2015-01-01

In prospective memory tasks different kinds of load can occur. Adding a prospective memory task can impose a load on ongoing task performance. Adding ongoing task load (OTL) can affect prospective memory performance. The existence of multiple target events increases prospective load (PL) and adding complexity to the to-be-remembered action increases retrospective load (RL). In two experiments, we systematically examined the effects of these different types of load on prospective memory performance. Results showed an effect of PL on costs in the ongoing task for categorical targets (Experiment 2), but not for specific targets (Experiment 1). RL and OTL both affected remembering the retrospective component of the prospective memory task. We suggest that PL can enhance costs in the ongoing task due to additional monitoring requirements. RL and OTL seem to impact the division of resources between the ongoing task and retrieval of the retrospective component, which may affect disengagement from the ongoing task. In general, the results demonstrate that the different types of load affect prospective memory differentially. PMID:26082709

Loads and loads and loads: the influence of prospective load, retrospective load, and ongoing task load in prospective memory.

Science.gov (United States)

Meier, Beat; Zimmermann, Thomas D

2015-01-01

In prospective memory tasks different kinds of load can occur. Adding a prospective memory task can impose a load on ongoing task performance. Adding ongoing task load (OTL) can affect prospective memory performance. The existence of multiple target events increases prospective load (PL) and adding complexity to the to-be-remembered action increases retrospective load (RL). In two experiments, we systematically examined the effects of these different types of load on prospective memory performance. Results showed an effect of PL on costs in the ongoing task for categorical targets (Experiment 2), but not for specific targets (Experiment 1). RL and OTL both affected remembering the retrospective component of the prospective memory task. We suggest that PL can enhance costs in the ongoing task due to additional monitoring requirements. RL and OTL seem to impact the division of resources between the ongoing task and retrieval of the retrospective component, which may affect disengagement from the ongoing task. In general, the results demonstrate that the different types of load affect prospective memory differentially.

Heptagon amplitude in the multi-Regge regime

International Nuclear Information System (INIS)

Bartels, J.

2014-05-01

As we have shown in previous work, the high energy limit of scattering amplitudes in N=4 supersymmetric Yang-Mills theory corresponds to the infrared limit of the 1-dimensional quantum integrable system that solves minimal area problems in AdS 5 . This insight can be developed into a systematic algorithm to compute the strong coupling limit of amplitudes in the multi-Regge regime through the solution of auxiliary Bethe Ansatz equations. We apply this procedure to compute the scattering amplitude for n=7 external gluons in different multi-Regge regions at infinite 't Hooft coupling. Our formulas are remarkably consistent with the expected form of 7-gluon Regge cut contributions in perturbative gauge theory. A full description of the general algorithm and a derivation of results is given in a forthcoming paper.

Overload protection: avoidance response to heavy plantar surface loading.

Science.gov (United States)

Robbins, S E; Hanna, A M; Gouw, G J

1988-02-01

Current footwear which are designed for use in running are examples of intentional biomechanical model integration into device design. The inadequacy of this footwear in protecting against injury is postulated to be due to fixation on inadequate models of locomotory biomechanics that do not provide for feedback control; in particular, an hypothesized plantar surface sensory-mediated feedback control system, which imparts overload protection during locomotion. A heuristic approach was used to identify the hypothesized system. A random series of loads (0 to 164 kg) was applied to the knee flexed at 90 degrees. In this testing system, plantar surface avoidance behavior was the difference between the sum of the leg weight and the load applied to the knee, and the load measured at the plantar surface; this was produced by activation of hip flexors. Significant avoidance behavior was found in all of the subjects (P less than 0.001). On all surfaces tested, including modern athletic footwear (P less than 0.001), its magnitude increased directly in relation to the load applied to the knee (P less than 0.001). There were significant differences in avoidance behavior in relation to the weight-bearing surfaces tested (P less than 0.05). With the identification of a feedback control system which would serve to moderate loading during locomotion, an explanation is provided as to why current athletic footwear do not protect and may be injurious; thus allowing the design of footwear which may be truly protective.

Cargo liability regimes

Science.gov (United States)

2001-01-01

There are at present at least three international regimes of maritime cargo liability in force in different countries of the world - the original Hague rules (1924), the updated version known as the Hague-Visby rules (1968, further amended 1979), and...

Cognitive Load and Self-Determination Theories Applied to E-Learning : Impact on Students' Participation and Academic Performance

NARCIS (Netherlands)

de Araujo Guerra Grangeia, Tiago; de Jorge, Bruno; Franci, Daniel; Martins Santos, Thiago; Vellutini Setubal, Maria Silvia; Schweller, Marcelo; de Carvalho-Filho, Marco Antonio

2016-01-01

BACKGROUND: Emergency clerkships expose students to a stressful environment that require multiple tasks, which may have a direct impact on cognitive load and motivation for learning. To address this challenge, Cognitive Load Theory and Self Determination Theory provided the conceptual frameworks to

Legal framework of the environmental regulatory regime

International Nuclear Information System (INIS)

Black, D.

1992-01-01

The growing concern regarding environmental issues has presented a number of new challenges to those exploring and developing the hydrocarbon reserves located on the Newfoundland continental shelf. Not the least of these challenges is the development of new technologies in the harsh environment of the North Atlantic; in addition, these new technologies must be implemented in an existing and ever-changing regulatory regime. The legal framework of the environmental regulatory regime relating to offshore development in Canada is reviewed along with some of the more important legislation involved in regulating environmental issues in the offshore area. The legal basis for exploration, development, and management of resources located on the Newfoundland continental shelf is the Canada-Newfoundland Accord on Joint Management of Offshore Oil and Gas Resources off Newfoundland and Labrador. Administration of the Accord is the responsibility of the Canada-Newfoundland Offshore Petroleum Board. To be able to apply Canadian laws to the continental shelf, legislation was passed including the Canadian Laws Offshore Application Act as well as the Act implementing the Accord. The latter gives the Offshore Petroleum Board authority to regulate all stages involved in bringing an oil pool to production, such as granting of licenses and work authorizations. Granting of such licenses and authorizations is subject to compliance with environmental requirements, and there are provisions against certain environmental offenses such as spills. Other federal legislation applicable to the offshore includes the Canada Shipping Act and the Canadian Environmental Protection Act

Structural Flight Loads Simulation Capability. Volume I.

Science.gov (United States)

1980-11-01

actuators. Load cells sense the resulting loads and give the console operator a positive readout of the loads being applied. The operator’s console...qialn StesSa We Elmn 57. .......... C ’D D .... .. .-- --- -.. ... . ..114 .. ETF’ ’IFEFI,--EIJT :_I’F3L- EL4 ?O cl l c...3.20. (concluded). 127 ra E j214 CbC ob) C-H ea) 4p U) ’-4 r4 128 EL4 UA f r c www aw r. 0 ag 0 . 0 mo > 4-) 0 .4-) en 010 44 1*5 1 I .IA U * . a) Z

Finite element simulation of pressure-loaded phase-field fractures

NARCIS (Netherlands)

Singh, N.; Verhoosel, C.V.; van Brummelen, E.H.

2018-01-01

A non-standard aspect of phase-field fracture formulations for pressurized cracks is the application of the pressure loading, due to the fact that a direct notion of the fracture surfaces is absent. In this work we study the possibility to apply the pressure loading through a traction boundary

Tissue loading created during spinal manipulation in comparison to loading created by passive spinal movements.

Science.gov (United States)

Funabashi, Martha; Kawchuk, Gregory N; Vette, Albert H; Goldsmith, Peter; Prasad, Narasimha

2016-12-01

Spinal manipulative therapy (SMT) creates health benefits for some while for others, no benefit or even adverse events. Understanding these differential responses is important to optimize patient care and safety. Toward this, characterizing how loads created by SMT relate to those created by typical motions is fundamental. Using robotic testing, it is now possible to make these comparisons to determine if SMT generates unique loading scenarios. In 12 porcine cadavers, SMT and passive motions were applied to the L3/L4 segment and the resulting kinematics tracked. The L3/L4 segment was removed, mounted in a parallel robot and kinematics of SMT and passive movements replayed robotically. The resulting forces experienced by L3/L4 were collected. Overall, SMT created both significantly greater and smaller loads compared to passive motions, with SMT generating greater anterioposterior peak force (the direction of force application) compared to all passive motions. In some comparisons, SMT did not create significantly different loads in the intact specimen, but did so in specific spinal tissues. Despite methodological differences between studies, SMT forces and loading rates fell below published injury values. Future studies are warranted to understand if loading scenarios unique to SMT confer its differential therapeutic effects.

In vivo facet joint loading of the canine lumbar spine.

Science.gov (United States)

Buttermann, G R; Schendel, M J; Kahmann, R D; Lewis, J L; Bradford, D S

1992-01-01

This study describes a technique to measure in vivo loads and the resultant load-contact locations in the facet joint of the canine lumbar spine. The technique is a modification of a previously described in vitro method that used calibrated surface strains of the lateral aspect of the right L3 cranial articular process. In the present study, strains were measured during various in vivo static and dynamic activities 3 days after strain gage implantation. The in vivo recording technique and its errors, which depend on the location of the applied facet loads, is described. The results of applying the technique to five dogs gave the following results. Relative resultant contact load locations on the facet tended to be in the central and caudal portion of the facet in extension activities, central and cranial in standing, and cranial and ventral in flexion or right-turning activities. Right-turning contact locations were ventral and cranial to left-turning locations. Resultant load locations at peak loading during walking were in the central region of the facet, whereas resultant load locations at minimum loading during walking were relatively craniad. This resultant load-contact location during a walk gait cycle typically migrated in an arc with a displacement of 4 mm from minimum to maximum loading. Static tests resulted in a range of facet loads of 0 N in flexion and lying to 185 N for two-legged standing erect, and stand resulted in facet loads of 26 +/- 15 N (mean +/- standard deviation [SD]). Dynamic tests resulted in peak facet loads ranging from 55 N while walking erect to 170 N for climbing up stairs. Maximum walk facet loads were 107 +/- 27 N. The technique is applicable to in vivo studies of a canine facet joint osteoarthritis model and may be useful for establishing an understanding of the biomechanics of low-back pain.

Effect of conditioner load on the polishing pad surface during chemical mechanical planarization process

Energy Technology Data Exchange (ETDEWEB)

Shin, Cheol Min; Qin, Hong Yi; Hong, Seok Jun; Jeon, Sang Hyuk; Kulkarni, Atul; Kim, Tae Sun [Sungkyunkwan University, Suwon (Korea, Republic of)

2016-12-15

During the Chemical mechanical planarization (CMP), the pad conditioning process can affect the pad surface characteristics. Among many CMP process parameters, the improper applied load on the conditioner arm may have adverse effects on the polyurethane pad. In this work, we evaluated the pad surface properties under the various conditioner arm applied during pad conditioning process. The conditioning pads were evaluated for surface topography, surface roughness parameters such as Rt and Rvk and Material removal rate (MRR) and within-wafer non-uniformity after wafer polishing. We observed that, the pad asperities were collapsed in the direction of conditioner rotation and blocks the pad pores applied conditioner load. The Rvk value and MRR were founded to be in relation with 4 > 1 > 7 kgF conditioner load. Hence, this study shows that, 4 kgF applied load by conditioner is most suitable for the pad conditioning during CMP.

Simulating the transient regime for main condensate system at Cernavoda NPP

International Nuclear Information System (INIS)

Nita, Iulian; Gheorghiu, Mihai; Prisecaru, Ilie; Dupleac, Daniel

2005-01-01

The purpose of this project is to make a Thermal Hydraulic Analysis of Main Condensate System for getting real-time answer of installation during regimes occurring during normal and abnormal operation. To obtain the analyses the MMS code was used. The boundaries of the systems analysis are extended to Main Feedwater System in order to get a realistic response of Deaerator equipment which are situated between those two systems and have entrances from both systems. In this way we made a complex analysis with main condenser and steam generators as boundaries. We obtained a model for the entire chain of condensate and feedwater preheater with interface just turbine bleed steam. From that we could reduce the number of assumptions necessary to make the analysis. The analyses consist in hydraulics and thermal hydraulics analyses, respectively. For the first case analysed are: - the nominal operation regime with main condensate pumps; - start-up regime with total circulate of condensate to condenser; - 25% MCR (Maximum Continuous Rate) regime (this regime was used in designing the condensate regulating valves at low flow; - 40% MCR regime (with circulate of some condensate flow to condenser); - operating regime of 60% MCR with one main condensate pump operating; - operating regime with auxiliary condensate pump; - operating regime with discharging a condensate flow to condensate storage tank. The thermal hydraulic analyses deal with normal and abnormal operating regimes, respectively. In the first case analysed are the following regimes: - nominal operating regime with main condensate pump operating 100% MCR; - transient regime, 100-80% MCR; - transient regime, 100-80-60% MCR with two pumps in operation and 60 % MCR with one main condensate pump in operation; - transient regime, 100-80-60-60-40 % MCR; - shut-down regime; - start-up regime from Hot zero power to rated power regime. Finally, for the abnormal operating regimes the analyses concerned: - transient regime 100

Room air conditioner load control under summer comfort constraint

OpenAIRE

Da Silva , David; Brancaccio , M; Duplessis , Bruno; Adnot , J

2010-01-01

International audience; Load control options interest is growing because it can represent a response to future network investments and to congestion problems. In this frame, the present paper gives a methodology to quantify the value of load control for heat pumps (room air conditioners), in small tertiary and residential buildings, considering the occupant's comfort and the electrical grid needs for load shift. This methodology was applied to a small office building where simulations were ma...

Prediction of a Densely Loaded Particle-Laden Jet using a Euler-Lagrange Dense Spray Model

Science.gov (United States)

Pakseresht, Pedram; Apte, Sourabh V.

2017-11-01

Modeling of a dense spray regime using an Euler-Lagrange discrete-element approach is challenging because of local high volume loading. A subgrid cluster of droplets can lead to locally high void fractions for the disperse phase. Under these conditions, spatio-temporal changes in the carrier phase volume fractions, which are commonly neglected in spray simulations in an Euler-Lagrange two-way coupling model, could become important. Accounting for the carrier phase volume fraction variations, leads to zero-Mach number, variable density governing equations. Using pressure-based solvers, this gives rise to a source term in the pressure Poisson equation and a non-divergence free velocity field. To test the validity and predictive capability of such an approach, a round jet laden with solid particles is investigated using Direct Numerical Simulation and compared with available experimental data for different loadings. Various volume fractions spanning from dilute to dense regimes are investigated with and without taking into account the volume displacement effects. The predictions of the two approaches are compared and analyzed to investigate the effectiveness of the dense spray model. Financial support was provided by National Aeronautics and Space Administration (NASA).

A comparison of measured wind park load histories with the WISPER and WISPERX load spectra

Science.gov (United States)

Kelley, N. D.

1995-01-01

The blade-loading histories from two adjacent Micon 65/13 wind turbines are compared with the variable-amplitude test-loading histories known as the WISPER and WISPERX spectra. These standardized loading sequences were developed from blade flapwise load histories taken from nine different horizontal-axis wind turbines operating under a wide range of conditions in Europe. The subject turbines covered a broad spectrum of rotor diameters, materials, and operating environments. The final loading sequences were developed as a joint effort of thirteen different European organizations. The goal was to develop a meaningful loading standard for horizontal-axis wind turbine blades that represents common interaction effects seen in service. In 1990, NREL made extensive load measurements on two adjacent Micon 65/13 wind turbines in simultaneous operation in the very turbulent environment of a large wind park. Further, before and during the collection of the loads data, comprehensive measurements of the statistics of the turbulent environment were obtained at both the turbines under test and at two other locations within the park. The trend to larger but lighter wind turbine structures has made an understanding of the expected lifetime loading history of paramount importance. Experience in the US has shown that the turbulence-induced loads associated with multi-row wind parks in general are much more severe than for turbines operating individually or within widely spaced environments. Multi-row wind parks are much more common in the US than in Europe. In this paper we report on our results in applying the methodology utilized to develop the WISPER and WISPERX standardized loading sequences using the available data from the Micon turbines. While the intended purpose of the WISPER sequences were not to represent a specific operating environment, we believe the exercise is useful, especially when a turbine design is likely to be installed in a multi-row wind park.

Asymptotic preserving and all-regime Lagrange-Projection like numerical schemes: application to two-phase flows in low mach regime

International Nuclear Information System (INIS)

Girardin, Mathieu

2014-01-01

Two-phase flows in Pressurized Water Reactors belong to a wide range of Mach number flows. Computing accurate approximate solutions of those flows may be challenging from a numerical point of view as classical finite volume methods are too diffusive in the low Mach regime. In this thesis, we are interested in designing and studying some robust numerical schemes that are stable for large time steps and accurate even on coarse meshes for a wide range of flow regimes. An important feature is the strategy to construct those schemes. We use a mixed implicit-explicit strategy based on an operator splitting to solve fast and slow phenomena separately. Then, we introduce a modification of a Suliciu type relaxation scheme to improve the accuracy of the numerical scheme in some regime of interest. Two approaches have been used to assess the ability of our numerical schemes to deal with a wide range of flow regimes. The first approach, based on the asymptotic preserving property, has been used for the gas dynamics equations with stiff source terms. The second approach, based on the all-regime property, has been used for the gas dynamics equations and the homogeneous two-phase flows models HRM and HEM in the low Mach regime. We obtained some robustness and stability properties for our numerical schemes. In particular, some discrete entropy inequalities are shown. Numerical evidences, in 1D and in 2D on unstructured meshes, assess the gain in term of accuracy and CPU time of those asymptotic preserving and all-regime numerical schemes in comparison with classical finite volume methods. (author) [fr

Computational characterization of ignition regimes in a syngas/air mixture with temperature fluctuations

KAUST Repository

Pal, Pinaki

2016-07-27

Auto-ignition characteristics of compositionally homogeneous reactant mixtures in the presence of thermal non-uniformities and turbulent velocity fluctuations were computationally investigated. The main objectives were to quantify the observed ignition characteristics and numerically validate the theory of the turbulent ignition regime diagram recently proposed by Im et al. 2015 [29] that provides a framework to predict ignition behavior . a priori based on the thermo-chemical properties of the reactant mixture and initial flow and scalar field conditions. Ignition regimes were classified into three categories: . weak (where deflagration is the dominant mode of fuel consumption), . reaction-dominant strong, and . mixing-dominant strong (where volumetric ignition is the dominant mode of fuel consumption). Two-dimensional (2D) direct numerical simulations (DNS) of auto-ignition in a lean syngas/air mixture with uniform mixture composition at high-pressure, low-temperature conditions were performed in a fixed volume. The initial conditions considered two-dimensional isotropic velocity spectrums, temperature fluctuations and localized thermal hot spots. A number of parametric test cases, by varying the characteristic turbulent Damköhler and Reynolds numbers, were investigated. The evolution of the auto-ignition phenomena, pressure rise, and heat release rate were analyzed. In addition, combustion mode analysis based on front propagation speed and computational singular perturbation (CSP) was applied to characterize the auto-ignition phenomena. All results supported that the observed ignition behaviors were consistent with the expected ignition regimes predicted by the theory of the regime diagram. This work provides new high-fidelity data on syngas ignition characteristics over a broad range of conditions and demonstrates that the regime diagram serves as a predictive guidance in the understanding of various physical and chemical mechanisms controlling auto

Policy Ideas, Knowledge Regimes and Comparative Political Economy

DEFF Research Database (Denmark)

Campbell, John L.; Pedersen, Ove K.

2015-01-01

Despite much attention to how ideas affect policy making, where these ideas come from is a blind spot in comparative political economy. We show that an important source of policy ideas are knowledge regimes—fields of policy research organizations. We show as well that the organization of knowledge...... to restore it by transforming their knowledge regimes, albeit in ways that are still shaped by the surrounding political and economic institutions. The effectiveness of their efforts is not guaranteed. The argument is based on an analysis of the evolution of knowledge regimes since the 1970s in the USA...... regimes is heavily influenced by the organization of their surrounding political economies such that knowledge regimes have particular national characters. Furthermore, when people perceive that the utility of their knowledge regime for the rest of the political economy breaks down, they often try...

A Special Fiber Optic Sensor for Measuring Wheel Loads of Vehicles on Highways

Directory of Open Access Journals (Sweden)

Norman W. Garrick

2008-04-01

Full Text Available This paper presents results from an investigation on a special optical fiber as a load sensor for application in Weigh-in-Motion (WIM systems to measure wheel loads of vehicles traveling at normal speed on highways. The fiber used has a unique design with two concentric light guiding regions of different effective optical path lengths, which has the potential to enable direct measurement of magnitudes as well as locations of forces acting at multiple points along a single fiber. The optical characteristic of the fiber for intended sensing purpose was first assessed by a simple fiber bending experiment and by correlating the bend radii with the output light signal intensities. A simple laboratory load transmitting/fiber bending device was then designed and fabricated to appropriately bend the optical fiber under applied loads in order to make the fiber work as load sensor. The device with the optical fiber was tested under a universal loading machine and an actual vehicle wheel in the laboratory. The test results showed a good relationship between the magnitude of the applied load and the output optical signal changes. The results also showed a good correlation between the time delay between the inner and outer core light pulses and the distance of the applied load as measured from the output end of the fiber.

Femoral loading mechanics in the Virginia opossum, Didelphis virginiana: torsion and mediolateral bending in mammalian locomotion.

Science.gov (United States)

Gosnell, W Casey; Butcher, Michael T; Maie, Takashi; Blob, Richard W

2011-10-15

Studies of limb bone loading in terrestrial mammals have typically found anteroposterior bending to be the primary loading regime, with torsion contributing minimally. However, previous studies have focused on large, cursorial eutherian species in which the limbs are held essentially upright. Recent in vivo strain data from the Virginia opossum (Didelphis virginiana), a marsupial that uses a crouched rather than an upright limb posture, have indicated that its femur experiences appreciable torsion during locomotion as well as strong mediolateral bending. The elevated femoral torsion and strong mediolateral bending observed in D. virginiana might result from external forces such as a medial inclination of the ground reaction force (GRF), internal forces deriving from a crouched limb posture, or a combination of these factors. To evaluate the mechanism underlying the loading regime of opossum femora, we filmed D. virginiana running over a force platform, allowing us to measure the magnitude of the GRF and its three-dimensional orientation relative to the limb, facilitating estimates of limb bone stresses. This three-dimensional analysis also allows evaluations of muscular forces, particularly those of hip adductor muscles, in the appropriate anatomical plane to a greater degree than previous two-dimensional analyses. At peak GRF and stress magnitudes, the GRF is oriented nearly vertically, inducing a strong abductor moment at the hip that is countered by adductor muscles on the medial aspect of the femur that place this surface in compression and induce mediolateral bending, corroborating and explaining loading patterns that were identified in strain analyses. The crouched orientation of the femur during stance in opossums also contributes to levels of femoral torsion as high as those seen in many reptilian taxa. Femoral safety factors were as high as those of non-avian reptiles and greater than those of upright, cursorial mammals, primarily because the load

Exchange Rate Regimes – A periodical overview and a critical analysis of exchange rate regimes in Kosovo

Directory of Open Access Journals (Sweden)

Flamur Bunjaku

2015-03-01

Full Text Available Exchange rate regimes and the monetary policy are the key instruments governments use to achieve their economic and financial objectives. Moreover, due to global financial crisis the latter instruments get more importance. Empirical evidences show that exchange rate regimes in Kosovo and its monetary policy throughout their development were mainly influenced by different political and historical developments. In regard of Euroisation of monetary system in Kosovo it was found that this action generated macro - financial stability in terms of inflation and price fluctuation. However, in terms of microeconomic aspects, the unilateral adaptation of Euro as the official currency of Kosovo failed to provide microeconomic advantages such as to export stimulation, and so forth. The main exchange rate regime systems were discussed focusing in their advantages and disadvantages, and it was concluded that there is no commonly accepted theory regarding the optimality of exchange rate regimes. In addition, the global financial crisis impact in the financial system of Kosovo is also discussed and it was found that negative impacts of global financial crisis were moderate and indirect.

[Effect of antecedent dry weather period on urban storm runoff pollution load].

Science.gov (United States)

Li, Li-qing; Yin, Cheng-qing; Kong, Ling-li; He, Qing-ci

2007-10-01

Twelve storm events were surveyed at Shilipu catchment in Wuhan City through three-year monitoring regime. The flow discharges, total suspended solids (TSS), chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in runoff were measured to study the mechanism of urban stormwater runoff pollution. The relationship between the event pollution load and the antecedent dry weather period was identified to discuss the influence of the urban surface sanitation management, operation of sewer pipe maintenance and rainfall characteristics on the urban stormwater runoff pollution. It was found that the antecedent dry weather period and runoff amount were the important determining factors in the generation of urban stormwater runoff pollution. The event pollution load was positively correlated to the antecedent dry weather period between two rainfall events (R2 = 0.95, p pollution loads. The best regression equation to estimate pollution load for storm events was developed based on the antecedent dry weather period and runoff depth. Source control including improving urban street sweeping activities and operation of sewer pipe maintenance should be made to reduce the amount of available pollutant over the dry days. It is important alternative to control urban stormwater runoff pollution for Hanyang District.

Comprehensive Review on Divisible Load Theory: Concepts, Strategies, and Approaches

Directory of Open Access Journals (Sweden)

Shamsollah Ghanbari

2014-01-01

Full Text Available There is extensive literature concerning the divisible load theory. The divisible load theory is mainly applied for scheduling in the area of distributed computing. It is based on the fact that the load can be divided into some arbitrarily independent parts, in which each part can be processed independently by a processor. This paper reviews the literature concerning the divisible load theory, while focusing on the details of the basic concepts, approaches, strategies, typologies, and open problems.

Thermal–structural analysis of ITER triangular support for dominant load verification

Energy Technology Data Exchange (ETDEWEB)

Kim, Yu-Gyeong, E-mail: aspirany@hhi.co.kr [Hyundai Heavy Industries Co., Ltd., 1000, Bangeojinsunhwando-ro, Dong-gu, Ulsan (Korea, Republic of); Hwang, Jong-Hyun; Jung, Yung-Jin [Hyundai Heavy Industries Co., Ltd., 1000, Bangeojinsunhwando-ro, Dong-gu, Ulsan (Korea, Republic of); Kim, Hyun-Soo; Ahn, Hee-Jae [National Fusion Research Institute, 113 Gwahangno, Yuseong-gu, Daejeon-si (Korea, Republic of)

2014-12-15

Highlights: • The load combination method is introduced to thermal–structural analysis for contradictive loads occurred simultaneously. • The one-way coupling analysis also conducted for thermal–structural analysis and its validity is checked by comparing with the load combination. • The dominant load for triangular support bracket is determined as the baking condition. - Abstract: The triangular support is located on the lower inner shell of vacuum vessel of ITER, which should be designed to withstand various loads such as nuclear heat, coolant pressure and so on. The appropriateness of its design is evaluated under the dominant load that could represent the most conservative condition among the design loads. In order to decide the dominant load, a valid method for thermal–structural analysis is firstly verified considering contradictory behaviors between heat and structural loads. In this paper, two approaches; one-way coupling and load combination, are introduced for thermal–structural analysis. The one-way coupling is a method generally used but has a limit to apply on contradictory conditions. The load combination could give a proper solution since it evaluates each load independently and then adds up each result linearly. Based on the results of each case, structural analysis for another load case, baking condition with incident, is conducted to find out which load is dominant for triangular support. Consequently, it is found that the baking condition is the dominant load for triangular support bracket. The proposed load combination method gives a physically reasonable solution which can be used as a reference for checking the validity of other thermal–structural analysis. It is expected that these results could be applied for manufacturing design of the triangular support under various load conditions.

Thermal–structural analysis of ITER triangular support for dominant load verification

International Nuclear Information System (INIS)

Kim, Yu-Gyeong; Hwang, Jong-Hyun; Jung, Yung-Jin; Kim, Hyun-Soo; Ahn, Hee-Jae

2014-01-01

Highlights: • The load combination method is introduced to thermal–structural analysis for contradictive loads occurred simultaneously. • The one-way coupling analysis also conducted for thermal–structural analysis and its validity is checked by comparing with the load combination. • The dominant load for triangular support bracket is determined as the baking condition. - Abstract: The triangular support is located on the lower inner shell of vacuum vessel of ITER, which should be designed to withstand various loads such as nuclear heat, coolant pressure and so on. The appropriateness of its design is evaluated under the dominant load that could represent the most conservative condition among the design loads. In order to decide the dominant load, a valid method for thermal–structural analysis is firstly verified considering contradictory behaviors between heat and structural loads. In this paper, two approaches; one-way coupling and load combination, are introduced for thermal–structural analysis. The one-way coupling is a method generally used but has a limit to apply on contradictory conditions. The load combination could give a proper solution since it evaluates each load independently and then adds up each result linearly. Based on the results of each case, structural analysis for another load case, baking condition with incident, is conducted to find out which load is dominant for triangular support. Consequently, it is found that the baking condition is the dominant load for triangular support bracket. The proposed load combination method gives a physically reasonable solution which can be used as a reference for checking the validity of other thermal–structural analysis. It is expected that these results could be applied for manufacturing design of the triangular support under various load conditions

The Fracture of Plasma-Treated Polyurethane Surface under Fatigue Loading

Directory of Open Access Journals (Sweden)

Ilya A. Morozov

2018-02-01

Full Text Available Plasma treatment of soft polymers is a promising technique to improve biomedical properties of the materials. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading. The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface. The observed damages are related to the high stiffness of the modified surface and its transition to the polymer substrate.

Making Promises Good: The Anti-Money Laundering Regime as a Multi-Purpose Tool for Governance

Directory of Open Access Journals (Sweden)

Stavros Katsios

2016-01-01

Full Text Available The creation of this international anti-money laundering regulatory regime is, contrary to itsneglect by the literature, important in two ways. First, it provides us with a second example -alongside the Basle Accord – with which we can examine how political barriers to regulatorycooperation and coordination might be overcome; without overstating the success of the antimoneylaundering regime the paper argues that a lot of the political circumstances that enabledcooperation and coordination to develop in this case can be applied in facing other economiccrime forms. The FATF case may help us to identify important political conditions that can fostercollective regulatory initiatives in the international financial area and especially in South EasternEurope. Additionally the anti-money laundering regime may be useful more directly in pursuingsome other regulatory and security goals of particular interest for the Balkan region. Specifically,the kinds of international cooperation and coordination that have been introduced to combatmoney laundering may help to strengthen international regulatory initiatives aimed at curbingcorruption, tax evasion and capital flight and fighting the threat deriving from internationalorganised crime and global terrorism.

On the regimes of premixing

Energy Technology Data Exchange (ETDEWEB)

Angelini, S.; Theofanous, T.G.; Yuen, W.W. [California Univ., Santa Barbara, CA (United States). Center for Risk Studies and Safety

1998-01-01

The conditions of the MAGICO-2000 experiment are extended to more broadly investigate the regimes of premixing, and the corresponding internal structures of mixing zones. With the help of the data and numerical simulations using the computer code PM-ALPHA, we can distinguish extremes of behavior dominated by inertia and thermal effects - we name these the inertia and thermal regimes, respectively. This is an important distinction that should guide future experiments aimed at code verification in this area. Interesting intermediate behaviors are also delineated and discussed. (author)

Simulating tokamak PFC performance using simultaneous dual beam particle loading with pulsed heat loading

Science.gov (United States)

Sinclair, Gregory; Gonderman, Sean; Tripathi, Jitendra; Ray, Tyler; Hassanein, Ahmed

2017-10-01

The performance of plasma facing components (PFCs) in a fusion device are expected to change due to high flux particle loading during operation. Tungsten (W) is a promising PFC candidate material, due to its high melting point, high thermal conductivity, and low tritium retention. However, ion irradiation of D and He have each shown to diminish the thermal strength of W. This work investigates the synergistic effect between ion species, using dual beam irradiation, on the thermal response of W during ELM-like pulsed heat loading. Experiments studied three different loading conditions: laser, laser + He+, and laser + He+ + D+. 100 eV He+ and D+ exposures used a flux of 3.0-3.5 x 1020 m-2 s-1. ELM-like loading was applied using a pulsed Nd:YAG laser at an energy density of 0.38-1.51 MJ m-2 (3600 1 ms pulses at 1 Hz). SEM imaging revealed that laser + He+ loading at 0.76 MJ m-2 caused surface melting, inhibiting fuzz formation. Increasing the laser fluence decreased grain size and increased surface pore density. Thermally-enhanced migration of trapped gases appear to reflect resultant molten morphology. This work was supported by the National Science Foundation PIRE project.

Refrigeration. Two-Phase Flow. Flow Regimes and Pressure Drop

DEFF Research Database (Denmark)

Knudsen, Hans-Jørgen Høgaard

2002-01-01

The note gives the basic definitions used in two-phase flow. Flow regimes and flow regimes map are introduced. The different contributions to the pressure drop are stated together with an imperical correlation from the litterature.......The note gives the basic definitions used in two-phase flow. Flow regimes and flow regimes map are introduced. The different contributions to the pressure drop are stated together with an imperical correlation from the litterature....

Initial transformer sizing for single-phase residential load

International Nuclear Information System (INIS)

Schneider, K.C.; Hoad, R.F.

1992-01-01

The purchase of distribution transformers represents a significant capital investment per year for an electric utility. Choosing the correct thermal and economic size transformer can help control this investment. This paper describes a method for determining the correct economic size of distribution transformers using end-use appliance load profiles and the ANSI/IEEE Standard C57.91-1981 thermal model. Although applied only to single family and multifamily residential load in this paper, the method can be extended to other types of load such as commercial or industrial

Degradation of normal portland and slag cement concrete under load, due to reinforcement corrosion

International Nuclear Information System (INIS)

Philipose, K.E.; Beaudoin, J.J.; Feldman, R.F.

1992-08-01

The corrosion of reinforcement is one of the major degradation mechanisms of reinforced concrete elements. The majority of studies published on concrete-steel corrosion have been conducted on unstressed specimens. Structural concrete, however, is subjected to substantial strain near the steel reinforcing bars that resist tensile loads, which results in a system of microcracks. This report presents the initial results of an investigation to determine the effect of applied load and microcracking on the rate of ingress of chloride ion and corrosion of steel in concrete. Simply-supported concrete beam specimens were loaded to give a maximum strain of about 600 με on the tension face. Chloride ion ingress on cores taken from loaded specimens was monitored using energy-dispersive X-ray analysis techniques. Corrosion current and rate measurements using linear polarization electrochemical techniques were also obtained on the same loaded specimens. Variables investigated included two concrete types, two steel cover-depths, three applied load levels, bonded and unbonded rebars and the exposure of tension and compression beam faces to chloride solution. One concrete mixture was made with type 10 Portland cement, the other with 75% blast furnace slag, 22% type 50 cement and 3% silica fume. The rate of chloride ion ingress into reinforced concrete, and hence the time for chloride ion to reach the reinforcing steel, is shown to be dependent on applied load and the concrete quality. The dependence of corrosion process descriptors - passive layer formation, initiation period and propagation period - on the level of applied load is discussed. (Author) (6 refs., 3 tabs., 10 figs.)

A Comparative Study of Load Balancing Algorithms in Cloud Computing Environment

OpenAIRE

Katyal, Mayanka; Mishra, Atul

2014-01-01

Cloud Computing is a new trend emerging in IT environment with huge requirements of infrastructure and resources. Load Balancing is an important aspect of cloud computing environment. Efficient load balancing scheme ensures efficient resource utilization by provisioning of resources to cloud users on demand basis in pay as you say manner. Load Balancing may even support prioritizing users by applying appropriate scheduling criteria. This paper presents various load balancing schemes in differ...

Probabilistic assessment of an aged highway bridge under traffic load

NARCIS (Netherlands)

Steenbergen, R.D.J.M.; Maljaars, J.; Morales Nápoles, O.; Abspoel, L.

2012-01-01

Existing civil infrastructure represents a large economic value. Within the actions applied to the bridges, the traffic load is, in general, the most significant variable action to be considered when the ultimate limit states are under investigation. Consequently, the traffic load models play an

Transition from the constant ion mobility regime to the ion-atom charge-exchange regime for bounded collisional plasmas

International Nuclear Information System (INIS)

Poggie, Jonathan; Sternberg, Natalia

2005-01-01

A numerical and analytical study of a planar, collisional, direct-current, plasma-wall problem is presented. The fluid model for the problem is first validated by comparing numerical solutions with experimental data for low-pressure (∼0.1 Pa) electrode sheaths with wall potentials on the order of -100 V. For electric potential, ion number density, and ion velocity, good agreement was found between theory and experiment from within the sheath out to the bulk plasma. The frictional drag resulting from ion-neutral collisions is described by a model incorporating both linear and quadratic velocity terms. In order to study the transition from the constant ion mobility regime (linear friction) to the ion-atom charge-exchange collision regime (quadratic friction), the theoretical model was examined numerically for a range of ion temperatures and ion-neutral collision rates. It was found that the solution profiles in the quasineutral plasma depend on the ion temperature. For low ion temperatures they are governed mainly by the ion-atom charge-exchange regime, whereas for high temperatures they are governed by the constant ion mobility regime. Quasineutral plasma models corresponding to these two limiting cases were solved analytically. In particular, an analytical plasma solution is given for the ion-atom charge exchange regime that includes the effects of ion inertia. In contrast to the quasineutral plasma, the sheath is always governed for low to moderate collision rates by the ion-atom charge-exchange regime, independent of the ion temperature. Varying the collision rate, it was shown that when the wall potential is sufficiently high, the sheath cannot be considered collisionless, even if the collision rate is quite small

Bone healing response in cyclically loaded implants: Comparing zero, one, and two loading sessions per day.

Science.gov (United States)

de Barros E Lima Bueno, Renan; Dias, Ana Paula; Ponce, Katia J; Wazen, Rima; Brunski, John B; Nanci, Antonio

2018-05-31

When bone implants are loaded, they are inevitably subjected to displacement relative to bone. Such micromotion generates stress/strain states at the interface that can cause beneficial or detrimental sequels. The objective of this study is to better understand the mechanobiology of bone healing at the tissue-implant interface during repeated loading. Machined screw shaped Ti implants were placed in rat tibiae in a hole slightly bigger than the implant diameter. Implants were held stable by a specially-designed bone plate that permits controlled loading. Three loading regimens were applied, (a) zero loading, (b) one daily loading session of 60 cycles with an axial force of 1.5 N/cycle for 7 days, and (c) two such daily sessions with the same axial force also for 7 days. Finite element analysis was used to characterize the mechanobiological conditions produced by the loading sessions. After 7 days, the implants with surrounding interfacial tissue were harvested and processed for histological, histomorphometric and DNA microarray analyses. Histomorphometric analyses revealed that the group subjected to repeated loading sessions exhibited a significant decrease in bone-implant contact and increase in bone-implant distance, as compared to unloaded implants and those subjected to only one loading session. Gene expression profiles differed during osseointegration between all groups mainly with respect to inflammatory and unidentified gene categories. The results indicate that increasing the daily cyclic loading of implants induces deleterious changes in the bone healing response, most likely due to the accumulation of tissue damage and associated inflammatory reaction at the bone-implant interface. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Cognitive Load and Self-Determination Theories Applied to E-Learning: Impact on Students' Participation and Academic Performance.

Science.gov (United States)

de Araujo Guerra Grangeia, Tiago; de Jorge, Bruno; Franci, Daniel; Martins Santos, Thiago; Vellutini Setubal, Maria Silvia; Schweller, Marcelo; de Carvalho-Filho, Marco Antonio

2016-01-01

Emergency clerkships expose students to a stressful environment that require multiple tasks, which may have a direct impact on cognitive load and motivation for learning. To address this challenge, Cognitive Load Theory and Self Determination Theory provided the conceptual frameworks to the development of a Moodle-based online Emergency Medicine course, inspired by real clinical cases. Three consecutive classes (2013-2015) of sixth-year medical students (n = 304) participated in the course, during a curricular and essentially practical emergency rotation. "Virtual Rounds" provided weekly virtual patients in narrative format and meaningful schemata to chief complaints, in order to simulate real rounds at Emergency Unit. Additional activities such as Extreme Decisions, Emergency Quiz and Electrocardiographic challenge offered different views of emergency care. Authors assessed student´s participation and its correlation with their academic performance. A survey evaluated students´ opinions. Students graduating in 2015 answered an online questionnaire to investigate cognitive load and motivation. Each student produced 1965 pageviews and spent 72 hours logged on. Although Clinical Emergency rotation has two months long, students accessed the online course during an average of 5.3 months. Virtual Rounds was the most accessed activity, and there was positive correlations between the number of hours logged on the platform and final grades on Emergency Medicine. Over 90% of students felt an improvement in their clinical reasoning and considered themselves better prepared for rendering Emergency care. Considering a Likert scale from 1 (minimum load) to 7 (maximum load), the scores for total cognitive load were 4.79±2.2 for Virtual Rounds and 5.56±1.96 for real medical rounds(pcognitive and motivational conceptual frameworks, seems to be a strong tool to engage students in learning. It may support them to manage the cognitive challenges involved in clinical care and

Analog quantum simulation of the Rabi model in the ultra-strong coupling regime.

Science.gov (United States)

Braumüller, Jochen; Marthaler, Michael; Schneider, Andre; Stehli, Alexander; Rotzinger, Hannes; Weides, Martin; Ustinov, Alexey V

2017-10-03

The quantum Rabi model describes the fundamental mechanism of light-matter interaction. It consists of a two-level atom or qubit coupled to a quantized harmonic mode via a transversal interaction. In the weak coupling regime, it reduces to the well-known Jaynes-Cummings model by applying a rotating wave approximation. The rotating wave approximation breaks down in the ultra-strong coupling regime, where the effective coupling strength g is comparable to the energy ω of the bosonic mode, and remarkable features in the system dynamics are revealed. Here we demonstrate an analog quantum simulation of an effective quantum Rabi model in the ultra-strong coupling regime, achieving a relative coupling ratio of g/ω ~ 0.6. The quantum hardware of the simulator is a superconducting circuit embedded in a cQED setup. We observe fast and periodic quantum state collapses and revivals of the initial qubit state, being the most distinct signature of the synthesized model.An analog quantum simulation scheme has been explored with a quantum hardware based on a superconducting circuit. Here the authors investigate the time evolution of the quantum Rabi model at ultra-strong coupling conditions, which is synthesized by slowing down the system dynamics in an effective frame.

Brazil in the global anticorruption regime

Directory of Open Access Journals (Sweden)

Marcos Tourinho

2018-03-01

Full Text Available Abstract Brazilian anticorruption law and institutions were significantly transformed in recent decades. This article traces those transformations and explains how the international anticorruption and money laundering regimes contributed to their development. It argues that those international regimes were internalised in the Brazilian system through three mechanisms: inspiration and legitimation, coercion, and implementation support, and were critical to the transformation of Brazilian institutions.

Antenna–load interactions at optical frequencies: impedance matching to quantum systems

International Nuclear Information System (INIS)

Olmon, R L; Raschke, M B

2012-01-01

The goal of antenna design at optical frequencies is to deliver optical electromagnetic energy to loads in the form of, e.g., atoms, molecules or nanostructures, or to enhance the radiative emission from such structures, or both. A true optical antenna would, on a qualitatively new level, control the light–matter interaction on the nanoscale for controlled optical signal transduction, radiative decay engineering, quantum coherent control, and super-resolution microscopy, and provide unprecedented sensitivity in spectroscopy. Resonant metallic structures have successfully been designed to approach these goals. They are called optical antennas in analogy to radiofrequency (RF) antennas due to their capability to collect and control electromagnetic fields at optical frequencies. However, in contrast to the RF, where exact design rules for antennas, waveguides, and antenna–load matching in terms of their impedances are well established, substantial physical differences limit the simple extension of the RF concepts into the optical regime. Key distinctions include, for one, intrinsic material resonances including quantum state excitations (metals, metal oxides, semiconductor homo- and heterostructures) and extrinsic resonances (surface plasmon/phonon polaritons) at optical frequencies. Second, in the absence of discrete inductors, capacitors, and resistors, new design strategies must be developed to impedance match the antenna to the load, ultimately in the form of a vibrational, electronic, or spin excitation on the quantum level. Third, there is as yet a lack of standard performance metrics for characterizing, comparing and quantifying optical antenna performance. Therefore, optical antenna development is currently challenged at all the levels of design, fabrication, and characterization. Here we generalize the ideal antenna–load interaction at optical frequencies, characterized by three main steps: (i) far-field reception of a propagating mode exciting an

Antenna-load interactions at optical frequencies: impedance matching to quantum systems.

Science.gov (United States)

Olmon, R L; Raschke, M B

2012-11-09

The goal of antenna design at optical frequencies is to deliver optical electromagnetic energy to loads in the form of, e.g., atoms, molecules or nanostructures, or to enhance the radiative emission from such structures, or both. A true optical antenna would, on a qualitatively new level, control the light-matter interaction on the nanoscale for controlled optical signal transduction, radiative decay engineering, quantum coherent control, and super-resolution microscopy, and provide unprecedented sensitivity in spectroscopy. Resonant metallic structures have successfully been designed to approach these goals. They are called optical antennas in analogy to radiofrequency (RF) antennas due to their capability to collect and control electromagnetic fields at optical frequencies. However, in contrast to the RF, where exact design rules for antennas, waveguides, and antenna-load matching in terms of their impedances are well established, substantial physical differences limit the simple extension of the RF concepts into the optical regime. Key distinctions include, for one, intrinsic material resonances including quantum state excitations (metals, metal oxides, semiconductor homo- and heterostructures) and extrinsic resonances (surface plasmon/phonon polaritons) at optical frequencies. Second, in the absence of discrete inductors, capacitors, and resistors, new design strategies must be developed to impedance match the antenna to the load, ultimately in the form of a vibrational, electronic, or spin excitation on the quantum level. Third, there is as yet a lack of standard performance metrics for characterizing, comparing and quantifying optical antenna performance. Therefore, optical antenna development is currently challenged at all the levels of design, fabrication, and characterization. Here we generalize the ideal antenna-load interaction at optical frequencies, characterized by three main steps: (i) far-field reception of a propagating mode exciting an antenna

Operational Constraints on Hydropeaking and its Effects on the Hydrologic and Thermal Regime of a River in Central Chile

Science.gov (United States)

Olivares, M. A.; Guzman, C.; Rossel, V.; De La Fuente, A.

2013-12-01

Hydropower accounts for about 44% of installed capacity in Chile's Central Interconnected System, which serves most of the Chilean population. Hydropower reservoir projects can affect ecosystems by changing the hydrologic regime and water quality. Given its volumen regulation capacity, low operation costs and fast response to demand fluctuations, reservoir hydropower plants commonly operate on a load-following or hydropeaking scheme. This short-term operational pattern produces alterations in the hydrologic regime downstream the reservoir. In the case of thermally stratified reservoirs, peaking operations can affect the thermal structure of the reservoir, as well as the thermal regime downstream. In this study, we assessed the subdaily hydrologic and thermal alteration donwstream of Rapel reservoir in Central Chile for alternative operational scenarios, including a base case and several scenarios involving minimum instream flow (Qmin) and maximum hourly ramping rates (ΔQmax). Scenarios were simulated for the stratification season of summer 2009-2012 in a grid-wide short-term economic dispatch model which prescribes hourly power production by every power plant on a weekly horizon. Power time series are then translated into time series of turbined flows at each hydropower plants. Indicators of subdaily hydrologic alteration (SDHA) were computed for every scenario. Additionally, turbined flows were used as input data for a three-dimensional hydrodynamic model (CWR-ELCOM) of the reservoir which simulated the vertical temperature profile in the reservoir and the outflow temperature. For the time series of outflow temperatures we computed several indicators of subdaily thermal alteration (SDTA). Operational constraints reduce the values of both SDHA and SDTA indicators with respect to the base case. When constraints are applied separately, the indicators of SDHA decrease as each type of constraint (Qmin or ΔQmax) becomes more stringent. However, ramping rate

The Bree problem with different yield stresses on-load and off-load and application to creep ratcheting

International Nuclear Information System (INIS)

Bradford, R.A.W.; Ure, J.; Chen, H.F.

2014-01-01

The ratchet boundaries and ratchet strains are derived for the Bree problem and an elastic-perfectly plastic material with different yield stresses on-load and off-load. The Bree problem consists of a constant uniaxial primary membrane stress and a cycling thermal bending stress. The ratchet problem with differing yield stresses is also solved for a modified loading in which both the primary membrane and thermal bending stresses cycle in-phase. The analytic solutions for the ratchet boundaries are compared with the results of deploying the linear matching method (LMM) and excellent agreement is found. Whilst these results are of potential utility for purely elastic–plastic behaviour, since yield stresses will often differ at the two ends of the cycle, the solution is also proposed as a means of assessing creep ratcheting via a creep ductility exhaustion approach. -- Highlights: • The Bree problem is solved for differing yield stresses on and off load. • The modified Bree problem with cycling primary load is also solved. • These solutions can be applied to creep ratcheting using a pseudo-yield stress

The Load Level of Modern Wind Turbines according to IEC 61400-1

International Nuclear Information System (INIS)

Freudenreich, K; Argyriadis, K

2007-01-01

The paper describes some effects on the load level of state-of-the art multi megawatt wind turbines introduced by the new edition of the standard IEC 61400-1:2005 W ind Turbines - Part 1: Design requirements . Compared to the previous edition, especially the extreme load determination has been modified by applying stochastic and statistical analyses. Within this paper the effect on the overall load level of wind turbines is demonstrated and occurring problems are discussed. Load simulations have been carried out for four state-of-the-art multi-megawatt wind turbines of different design concepts and from different manufacturers. The blade root bending moments and tip deflection have been determined by applying different extrapolation methods. Advantages and disadvantages of these methods and tail fittings for different load components and wind turbine technologies are discussed and interpreted. Further on, the application of the extreme turbulence model is demonstrated. The dependence of the load level on the turbulence intensity and control system, as well as the interaction with extrapolated loads is discussed and limitations outlined. The obtained load level is compared to the overall load level of the turbines according to the previous edition of the standard, IEC 61400-1:1999

A Preliminary Study on Bucket Foundations under Transient Lateral Loading

DEFF Research Database (Denmark)

Foglia, Aligi; Ibsen, Lars Bo; Nielsen, Søren Kjær

2013-01-01

This study aims at investigating the behaviour of monopod bucket foundations through a physical model. The foundation is installed in dense water-saturated sand and is subjected to lateral load applied at different rates. The different loading rates allow for exploring the patterns of response of...

Artificial Neural Networks for SCADA Data based Load Reconstruction (poster)

NARCIS (Netherlands)

Hofemann, C.; Van Bussel, G.J.W.; Veldkamp, H.

2011-01-01

If at least one reference wind turbine is available, which provides sufficient information about the wind turbine loads, the loads acting on the neighbouring wind turbines can be predicted via an artificial neural network (ANN). This research explores the possibilities to apply such a network not

Macro and Microscopic Investigation on Fracture Specimen of Alloy 617 Base Metal and Weldment in Low Cycle Fatigue Regime

International Nuclear Information System (INIS)

Kim, Seon Jin; Dewa, Rando Tungga; Kim, Won Gon

2016-01-01

This paper investigates macro- and microscopic fractography performed on fracture specimens from low cycle fatigue (LCF) testings through an Alloy 617 base metal and weldments. The weldment specimens were taken from gas tungsten arc welding (GTAW) pad of Alloy 617. The aim of the present study is to investigate the macro- and microscopic aspects of the low cycle fatigue fracture mode and mechanism of Alloy 617 base metal and GTAWed weldment specimens. Fully axial total strain controlled fatigue tests were conducted at room temperature with total strain ranges of 0.6, 0.9, 1.2 and 1.5%. Macroscopic fracture surfaces of Alloy 617 base metal specimens showed a flat type normal to the fatigue loading direction, whereas the GTAWed weldment specimens were of a shear/star type. The fracture surfaces of both the base metal and weldment specimens revealed obvious fatigue striations at the crack propagation regime. In addition, the fatigue crack mechanism of the base metal showed a transgranular normal to fatigue loading direction; however, the GTAWed weldment specimens showed a transgranular at approximately 45° to the fatigue loading direction

Macro and Microscopic Investigation on Fracture Specimen of Alloy 617 Base Metal and Weldment in Low Cycle Fatigue Regime

Energy Technology Data Exchange (ETDEWEB)

Kim, Seon Jin; Dewa, Rando Tungga [Pukyung National Univ., Busan (Korea, Republic of); Kim, Won Gon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-06-15

This paper investigates macro- and microscopic fractography performed on fracture specimens from low cycle fatigue (LCF) testings through an Alloy 617 base metal and weldments. The weldment specimens were taken from gas tungsten arc welding (GTAW) pad of Alloy 617. The aim of the present study is to investigate the macro- and microscopic aspects of the low cycle fatigue fracture mode and mechanism of Alloy 617 base metal and GTAWed weldment specimens. Fully axial total strain controlled fatigue tests were conducted at room temperature with total strain ranges of 0.6, 0.9, 1.2 and 1.5%. Macroscopic fracture surfaces of Alloy 617 base metal specimens showed a flat type normal to the fatigue loading direction, whereas the GTAWed weldment specimens were of a shear/star type. The fracture surfaces of both the base metal and weldment specimens revealed obvious fatigue striations at the crack propagation regime. In addition, the fatigue crack mechanism of the base metal showed a transgranular normal to fatigue loading direction; however, the GTAWed weldment specimens showed a transgranular at approximately 45° to the fatigue loading direction.

A simplified technique for shakedown load determination

International Nuclear Information System (INIS)

Abdalla, H.F.; Younan, M.Y.A.; Megahed, M.M.

2005-01-01

In this paper a simple technique is presented to determine the limit shakedown load of a structure or a component using the finite element method. Through the proposed technique, the limit shakedown load is determined without performing time consuming cyclic loading simulations or iterative elastic techniques. Instead, it is determined by performing only two analyses namely, an elastic analysis and an elastic-plastic analysis. By extracting the results of the two analyses, the limit shakedown load of the structure is determined through the calculation of the residual stresses. The technique is applied and verified using two bench mark shakedown problems namely: the two-bar structure subjected to constant axial force and cyclic thermal loading, and the Bree cylinder subjected to constant internal pressure and cyclic high heat fluxes across its wall. The results of the proposed technique showed very good correlation with the, analytically determined, Bree diagrams of both structures. Moreover, the outcomes of the proposed technique showed very good results in comparison to full cyclic loading elasto-plastic finite element simulations of both structures. (authors)

Load Management in District Heating Operation

DEFF Research Database (Denmark)

Li, Hongwei; Wang, Stephen Jia

2015-01-01

Smooth operation of district heating system will avoid installation of expensive peak heat boilers, improve plant partial load performance, increase the system redundancy for further network expansion and improve its resilience to ensure security of supply during severe heating seasons. The peak...... heating load can be reduced through building demand side management. The building thermal mass can be used to shift the heating supply under the circumstance without jeopardizing the consumer thermal comfort. In this paper, the multi-agent framework is applied to a simplified building dynamic model...

Response of stiff piles in sand to long-term cyclic lateral loading

DEFF Research Database (Denmark)

Bakmar, Christian LeBlanc; Houlsby, Guy T.; Byrne, Byron W.

2010-01-01

. To address this, a series of laboratory tests were conducted where a stiff pile in drained sand was subjected to between 8000 and 60000 cycles of combined moment and horizontal loading. A typical design for an offshore wind turbine monopile was used as a basis for the study, to ensure that pile dimensions...... and loading ranges were realistic. A complete non-dimensional framework for stiff piles in sand is presented and applied to interpret the test results. The accumulated rotation was found to be dependent on relative density and was strongly affected by the characteristics of the applied cyclic load. The pile...... stiffness increased with number of cycles, which contrasts with the current methodology where static p - y curves are degraded to account for cyclic loading. Methods are presented to predict the change in stiffness and the accumulated rotation of a stiff pile due to long-term cyclic loading. The use...

Experimental buckling investigation of ring-stiffened cyclindrical shells under unsymmetrical axial loads

International Nuclear Information System (INIS)

Baker, W.E.; Bennett, J.G.; Babcock, C.D.

1983-01-01

Six steel shells having nuclear containment-like features were fabricated and loaded to failure with an offset axial load. The shells of R/t = 500 buckled plastically. Four of the shells had reinforced circular cutouts. These penetrations were sized to cut no ring-stiffener, a single, two- or three-ring stiffeners. Reinforcing and framing around the penetrations were based upon the area-replacement rule of the applicable portion of the American Society for Mechanical Engineers (ASME) Boiler and Pressure Vessel Code and were of a design to simulate actual practice for nuclear steel containments. Prior to testing, imperfections were measured and strain gages were applied to determine information on load distribution at the ends of the cylinder and strain fields at areas likely to buckle. Buckling loads were determined for an axial load applied with an eccentricity of R/2 where R is the cylinder radius

Regimes of the magnetized Rayleigh endash Taylor instability

International Nuclear Information System (INIS)

Winske, D.

1996-01-01

Hybrid simulations with kinetic ions and massless fluid electrons are used to investigate the linear and nonlinear behavior of the magnetized Rayleigh endash Taylor instability in slab geometry with the plasma subject to a constant gravity. Three regimes are found, which are determined by the magnitude of the complex frequency ω=ω r +iγ. For |ω| i (Ω i = ion gyrofrequency), one finds the typical behavior of the usual fluid regime, namely the development of open-quote open-quote mushroom-head close-quote close-quote spikes and bubbles in the density and a strongly convoluted boundary between the plasma and magnetic field, where the initial gradient is not relaxed much. A second regime, where |ω|∼0.1Ω i , is characterized by the importance of the Hall term. Linearly, the developing flute modes are more finger-like and tilted along the interface; nonlinearly, clump-like structures form, leading to a significant broadening of the interface. The third regime is characterized by unmagnetized ion behavior, with |ω|∼Ω i . Density clumps, rather than flutes, form in the linear stage, while nonlinearly, longer-wavelength modes that resemble those in fluid regime dominate. Finite Larmor radius stabilization of short-wavelength modes is observed in each regime. copyright 1996 American Institute of Physics

Numerical simulation of transitions between back discharge regimes

International Nuclear Information System (INIS)

Jansky, Jaroslav; Lemont, Florent; Bessieres, Delphine; Paillol, Jean

2014-01-01

This paper presents numerical simulations of transitions between back discharge regimes. Back discharge refers to any discharge initiated at or near a dielectric layer covering a passive electrode. In this work, a pinhole in a dielectric layer on a plane anode serves as a model for back discharge activity. We have studied transitions between back discharge regimes by varying the surface charge density on the dielectric layer and the electric field in front of the pinhole. From the variation of these two independent parameters, the back discharge regimes have been depicted as a mode diagram inspired by the experimental study of Masuda and Mizuno. The resulting diagram includes the different discharge regimes that are commonly observed in experiments. The propagation of a positive ionizing wave inside the pinhole toward its edge, and the resulting formation of a plasma zone at its exit constitute the onset stage of back discharge. From this stage, the transitions to volume discharge or surface discharge can occur. The volume discharge regime consists of the propagation of a discharge in space toward the cathode which can be superimposed with the propagation of a discharge above the dielectric layer surface. The diagram reveals the conditions for transitions between back discharge regimes. (authors)

Microwave heating device for internal heating convection experiments, applied to Earth's mantle dynamics

Energy Technology Data Exchange (ETDEWEB)

Surducan, E.; Surducan, V.; Neamtu, C., E-mail: camelia.neamtu@itim-cj.ro [National Institute for Research and Development of Isotopic and Molecular Technologies (INCDTIM), 67-103 Donat St., 400293, Cluj‑Napoca (Romania); Limare, A.; Di Giuseppe, E. [Institut de Physique du Globe de Paris (IPGP), Univ. Paris Diderot, UMR CNRS 7154, 1 rue Jussieu, 75005, Paris (France)

2014-12-15

We report the design, construction, and performances of a microwave (MW) heating device for laboratory experiments with non-contact, homogeneous internal heating. The device generates MW radiation at 2.47 GHz from a commercial magnetron supplied by a pulsed current inverter using proprietary, feedback based command and control hardware and software. Specially designed MW launchers direct the MW radiation into the sample through a MW homogenizer, devised to even the MW power distribution into the sample's volume. An adjustable MW circuit adapts the MW generator to the load (i.e., the sample) placed in the experiment chamber. Dedicated heatsinks maintain the MW circuits at constant temperature throughout the experiment. Openings for laser scanning for image acquisition with a CCD camera and for the cooling circuits are protected by special MW filters. The performances of the device are analyzed in terms of heating uniformity, long term output power stability, and load matching. The device is used for small scale experiments simulating Earth's mantle convection. The 30 × 30 × 5 cm{sup 3} convection tank is filled with a water‑based viscous fluid. A uniform and constant temperature is maintained at the upper boundary by an aluminum heat exchanger and adiabatic conditions apply at the tank base. We characterize the geometry of the convective regime as well as its bulk thermal evolution by measuring the velocity field by Particle Image Velocimetry and the temperature field by using Thermochromic Liquid Crystals.

Friction and anchorage loading revisited.

Science.gov (United States)

Dholakia, Kartik D

2012-01-01

Contemporary concepts of sliding mechanics explain that friction is inevitable. To overcome this frictional resistance, excess force is required to retract the tooth along the archwire (ie, individual retraction of canines, en masse retraction of anterior teeth), in addition to the amount of force required for tooth movement. The anterior tooth retraction force, in addition to excess force (to overcome friction), produces reciprocal protraction force on molars, thereby leading to increased anchorage loading. However, this traditional concept was challenged in recent literature, which was based on the finite element model, but did not bear correlation to the clinical scenario. This article will reinforce the fact that clinically, friction increases anchorage loading in all three planes of space, considering the fact that tooth movement is a quasistatic process rather than a purely continuous or static one, and that conventional ways of determining the effects of static or dynamic friction on anchorage load cannot be applied to clinical situations (which consist of anatomical resistance units and a complex muscular force system). The article does not aim to quantify friction and its effect on the amount of anchorage load. Rather, a new perspective regarding the role of various additional factors (which is not explained by contemporary concept) that may influence friction and anchorage loading is provided..

Competition Regime

Directory of Open Access Journals (Sweden)

Danilo Icaza Ortiz

2013-01-01

Full Text Available This paper is a review of the competition regime works of various authors, published under the auspices of the University of the Hemispheres and the Corporation for Studies and Publications. Analyzes the structure, the general concepts, case law taken for development. Includes comments on the usefulness of this work for the study of competition law and the contribution to the lawyers who want to practice in this branch of economic law.

The international climate regime: towards consolidation collapse

International Nuclear Information System (INIS)

Berthaud, P.; Cavard, D.; Criqui, P.

2003-10-01

This article deals with the different modalities that exist to manage a problem of collective action in the field of climate negotiation. It uses two concepts of the International Political Economy (IPE): the concept of International Regime (IR) and the concept of Hegemony and / or Leadership. The course the international negotiation has taken between 1992 (Rio Convention) and march 2001 (the US rejection of the Kyoto Protocol of 1997) leads us, first, to question the conditions of existence as well as the viability of a non-hegemonic International Regime (Part One). Then, we discuss the perspectives for the 'post - Kyoto' era. After having examined the preferences of the three most active actors in the negotiation (USA, Europe, G77 + China) combined with the leadership capacities they possess, we identify three scenarios for the future: i) anarchy, ii) an international regime under the American hegemony, iii) an international regime under the European leadership (Part Two). (author)

Probability Based Evaluation of Vehicular Bridge Load using Weigh-in-Motion Data

Directory of Open Access Journals (Sweden)

Widi Nugraha

2016-02-01

Full Text Available Load and Resistance Factored Design (LRFD method for designing bridge in Indonesia have been implemented for more than 25 years. LRFD method treating loads and strengths variables as random variables with specific safety factors for different loads and strengths variables type. The nominal loads, load factors, reduction factors, and other criteria for bridge design code can be determined to meet the reliability criteria. Statistical data of weigh-in-motion (WIM vehicular loads measurement in Northern Java highway, Cikampek - Pamanukan, West Java (2011, used in as statistical loads variable. A 25 m simple span bridge with reinforced concrete T-girder is used as a model for structural analysis due to WIM measured and nominal vehicular load based on RSNI T-02-2005, with applied bending moment of girder as the output. The distribution fitting result of applied bending moment due to WIM measured vehicular loads is lognormal. The maximum bending moment due to RSNI T-02-2005 nominal vehicular load is 842.45 kN-m and has probability of exceedance of 5x10-5. It can be concluded, for this study, that the bridge designed using RSNI T-02-2005 is safely designed, since it has reliability index, β of 5.02, higher than target reliability, β ranging from 3.50 or 3.72.

Experimental Testing of Monopiles in Sand Subjected to One-Way Long-Term Cyclic Lateral Loading

DEFF Research Database (Denmark)

Roesen, Hanne Ravn; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

2013-01-01

In the offshore wind turbine industry the most widely used foundation type is the monopile. Due to the wave and wind forces the monopile is subjected to a strong cyclic loading with varying amplitude, maximum loading level, and varying loading period. In this paper the soil–pile interaction...... of a monopile in sand subjected to a long-term cyclic lateral loading is investigated by means of small scale tests. The tests are conducted with a mechanical loading rig capable of applying the cyclic loading as a sine signal with varying amplitude, mean loading level, and loading period for more than 60 000...... cycles. The tests are conducted in dense saturated sand. The maximum moment applied in the cyclic tests is varied from 18% to 36% of the ultimate lateral resistance found in a static loading test. The tests reveal that the accumulated rotation can be expressed by use of a power function. Further, static...

Institutional design and regime effectiveness in transboundary river management – the Elbe water quality regime

Directory of Open Access Journals (Sweden)

I. Dombrowsky

2008-02-01

Full Text Available The literature on transboundary river management suggests that institutions play an important role in bringing about cooperation. However, knowledge about how such institutions should be designed in order to do so remains limited. One way to learn more about adequate institutional design is to assess the effectiveness of existing regimes, and to trace the causal relationships that lead to the respective outcomes. In order to gain further insights into the relationship between institutional design and regime effectiveness, this paper presents a study on the water quality regime of the International Commission for the Protection of the Elbe (ICPE. The analysis is based on a review of pertinent documents and ten qualitative interviews with Czech and German Commission members and NGO representatives. Particular emphasis has been put on determining the ICPE's specific contribution and the no-regime counterfactual as well as on the perceived expediency of the institutional arrangements. The study shows overall that the countries were relatively successful in improving water quality in the Elbe basin. However, this outcome can only partly be attributed to the ICPE itself. Furthermore, the ICPE's contribution towards achieving the various goals varied significantly between the different areas of activity: it was relatively significant where the main responsibility for action lay with the public authorities, such as in the area of wastewater treatment and the establishment of an international alarm plan and model, but was practically non-existent in the reduction of non-point pollution from agriculture, where success depended on the behavior of individual private actors (farmers. The commission contributed towards problem solving by serving as a forum for the joint identification of priorities for action from a basin-wide perspective. The resulting international obligations increased the power of national water administrations and their access to funds

STRUCTURAL RESPONSE OF THE DIII-D TOROIDAL FIELD COIL TO INCREASED LATERAL LOADS

International Nuclear Information System (INIS)

REIS, E.E; CHIN, E.

2004-03-01

OAK-B135 Recent calibration shots in which full toroidal field (TF) coil current interacted with the maximum poloidal field coils have produced increased lateral loads on the outer sections of the TF-coil. The increased lateral loads have resulted in deflections that have been sufficient to cause the TF-coil to contact adjacent equipment and produce a transient short to ground within the coil. The six outer turns of each TF-coil bundle are clamped together by insulated preloaded studs to provide increased bending stiffness. These sections of the outer bundles depend on friction to react the lateral loads as a bundle rather than six individual turns. A major concern is that the increased loads will produce slip between turns resulting in excessive lateral deflections and possible damage to the insulating sleeve on the preloaded studs. A finite element structural model of the TF-coil was developed for the calculation of deflections and the shear load distribution throughout the coil for the applied lateral loads from a full current calibration shot. The purpose of the updated structural model is to correlate the applied lateral loads to the total shear force between the unbonded sections of the outer turns. An allowable integrated lateral load applied to the outer turns is established based on the maximum shear force that can be reacted by friction. A program that calculates the magnetic fields and integrated lateral load along the outer turns can be incorporated into the plasma control system. The integrated load can then be compared to the calculated allowable value prior to execution of calibration shots. Calibration shots with a calculated total lateral load greater than the allowable value will be prevented

On the dynamic stability of shear deformable beams under a tensile load

Science.gov (United States)

Caddemi, S.; Caliò, I.; Cannizzaro, F.

2016-07-01

Loss of stability of beams in a linear static context due to the action of tensile loads has been disclosed only recently in the scientific literature. However, tensile instability in the dynamic regime has been only marginally covered. Several aspects concerning the role of shear deformation on the tensile dynamic instability on continuous and discontinuous beams are still to be addressed. It may appear as a paradox, but also for the case of the universally studied Timoshenko beam model, despite its old origin, frequency-axial load diagrams in the range of negative values of the load (i.e. tensile load) has never been brought to light. In this paper, for the first time, the influence of a conservative tensile axial loads on the dynamic behaviour of the Timoshenko model, according to the Haringx theory, is assessed. It is shown that, under increasing tensile loads, regions of positive/negative fundamental frequency variations can be distinguished. In addition, the beam undergoes eigen-mode changes, from symmetric to anti-symmetric shapes, until tensile instability of divergence type is reached. As a further original contribution on the subject, taking advantage of a new closed form solution, it is shown that the same peculiarities are recovered for an axially loaded Euler-Bernoulli vibrating beam with multiple elastic sliders. This latter model can be considered as the discrete counterpart of the Timoshenko beam-column in which the internal sliders concentrate the shear deformation that in the Timoshenko model is continuously distributed. Original aspects regarding the evolution of the vibration frequencies and the relevant mode shapes with the tensile load value are highlighted.

Global regime shift dynamics of catastrophic sea urchin overgrazing

Science.gov (United States)

Ling, S. D.; Scheibling, R. E.; Rassweiler, A.; Johnson, C. R.; Shears, N.; Connell, S. D.; Salomon, A. K.; Norderhaug, K. M.; Pérez-Matus, A.; Hernández, J. C.; Clemente, S.; Blamey, L. K.; Hereu, B.; Ballesteros, E.; Sala, E.; Garrabou, J.; Cebrian, E.; Zabala, M.; Fujita, D.; Johnson, L. E.

2015-01-01

A pronounced, widespread and persistent regime shift among marine ecosystems is observable on temperate rocky reefs as a result of sea urchin overgrazing. Here, we empirically define regime-shift dynamics for this grazing system which transitions between productive macroalgal beds and impoverished urchin barrens. Catastrophic in nature, urchin overgrazing in a well-studied Australian system demonstrates a discontinuous regime shift, which is of particular management concern as recovery of desirable macroalgal beds requires reducing grazers to well below the initial threshold of overgrazing. Generality of this regime-shift dynamic is explored across 13 rocky reef systems (spanning 11 different regions from both hemispheres) by compiling available survey data (totalling 10 901 quadrats surveyed in situ) plus experimental regime-shift responses (observed during a total of 57 in situ manipulations). The emergent and globally coherent pattern shows urchin grazing to cause a discontinuous ‘catastrophic’ regime shift, with hysteresis effect of approximately one order of magnitude in urchin biomass between critical thresholds of overgrazing and recovery. Different life-history traits appear to create asymmetry in the pace of overgrazing versus recovery. Once shifted, strong feedback mechanisms provide resilience for each alternative state thus defining the catastrophic nature of this regime shift. Importantly, human-derived stressors can act to erode resilience of desirable macroalgal beds while strengthening resilience of urchin barrens, thus exacerbating the risk, spatial extent and irreversibility of an unwanted regime shift for marine ecosystems.

U^{28+}-intensity record applying a H_{2}-gas stripper cell

Directory of Open Access Journals (Sweden)

Winfried Barth

2015-04-01

Full Text Available To meet the Facility for Antiproton and Ion Research science requirements higher beam intensity has to be achieved in the present GSI-accelerator complex. For this an advanced upgrade program for the UNILAC is ongoing. Stripping is a key technology for all heavy ion accelerators. For this an extensive research and development program was carried out to optimize for high brilliance heavy ion operation. After upgrade of the supersonic N_{2}-gas jet (2007, implementation of high current foil stripping (2011 and preliminary investigation of H_{2}-gas jet operation (2012, recently (2014 a new H_{2}-gas cell using a pulsed gas regime synchronized with arrival of the beam pulse has been developed. An obviously enhanced stripper gas density as well as a simultaneously reduced gas load for the pumping system result in an increased stripping efficiency, while the beam emittance remains the same. A new record intensity (7.8 emA for ^{238}U^{28+} beams at 1.4  MeV/u has been achieved applying the pulsed high density H_{2} stripper target to a high intensity ^{238}U^{4+} beam from the VARIS ion source with a newly developed extraction system. The experimental results are presented in detail.

World-Ecology and Ireland: The Neoliberal Ecological Regime

Directory of Open Access Journals (Sweden)

Sharae Deckard

2016-03-01

Full Text Available Since the collapse of the Celtic Tiger, the socio-economic particularity of neoliberal capitalism in its Irish manifestation has increasingly been critiqued, but little attention has been paid to neoliberalism as ecology within Ireland. This article conducts an exploratory survey of the characteristics of the Irish neoliberal ecological regime during and after the Celtic Tiger, identifying the opening of new commodity frontiers (such as fracking, water, agro-biotechnology, and biopharma constituted in the neoliberal drive to appropriate and financialize nature. I argue for the usefulness of applying not only the tools of world-systems analysis, but also Jason W. Moore’s world-ecological paradigm, to analysis of Ireland as a semi-periphery. What is crucial to a macro-ecological understanding of Ireland’s role in the neoliberal regime of the world-ecology is the inextricability of its financial role as a tax haven and secrecy jurisdiction zone from its environmental function as a semi-peripheral pollution and water haven. We can adapt Jason W. Moore’s slogan that “Wall Street…becomes a way of organizing all of nature, characterized by the financialization of any income-generating activity” (Moore 2011b: 39 to say that to say that the “IFSC is a way of organizing nature,” with pernicious consequences for water, energy, and food systems in Ireland. Financial service centers and pharmaceutical factories, plantations and cattle ranches, tax havens and pollution havens, empires and common markets are all forms of environment-making that constellate human relations and extra-human processes into new ecological regimes. More expansive, dialectical understandings of “ecology” as comprising the whole of socio-ecological relations within the capitalist world-ecology—from farming to pharma to financialization—are crucial to forming configurations of knowledge able not only to take account of Ireland’s role in the environmental

Pay-load Estimation of a 2 DOF Flexible Link Robot

DEFF Research Database (Denmark)

Poulsen, Niels Kjølstad; Ravn, Ole

2005-01-01

. Although the applied principle might be general in nature, the pa-per is applied to the well-known problem of identifying a pay-load of a moving flexible robot. This problem is almost impossible to solve by measurements, so an estimation technique must be applied. The presented method benefits from...

Open Architecture Data System for NASA Langley Combined Loads Test System

Science.gov (United States)

Lightfoot, Michael C.; Ambur, Damodar R.

1998-01-01

The Combined Loads Test System (COLTS) is a new structures test complex that is being developed at NASA Langley Research Center (LaRC) to test large curved panels and cylindrical shell structures. These structural components are representative of aircraft fuselage sections of subsonic and supersonic transport aircraft and cryogenic tank structures of reusable launch vehicles. Test structures are subjected to combined loading conditions that simulate realistic flight load conditions. The facility consists of two pressure-box test machines and one combined loads test machine. Each test machine possesses a unique set of requirements or research data acquisition and real-time data display. Given the complex nature of the mechanical and thermal loads to be applied to the various research test articles, each data system has been designed with connectivity attributes that support both data acquisition and data management functions. This paper addresses the research driven data acquisition requirements for each test machine and demonstrates how an open architecture data system design not only meets those needs but provides robust data sharing between data systems including the various control systems which apply spectra of mechanical and thermal loading profiles.

Density-dependent electron scattering in photoexcited GaAs in strongly diffusive regime

DEFF Research Database (Denmark)

Mics, Zoltán; D’Angio, Andrea; Jensen, Søren A.

2013-01-01

In a series of systematic optical pump–terahertz probe experiments, we study the density-dependent electron scattering rate in photoexcited GaAs in the regime of strong carrier diffusion. The terahertz frequency-resolved transient sheet conductivity spectra are perfectly described by the Drude...... model, directly yielding the electron scattering rates. A diffusion model is applied to determine the spatial extent of the photoexcited electron-hole gas at each moment after photoexcitation, yielding the time-dependent electron density, and hence the density-dependent electron scattering time. We find...

Insights in the Rhodium-Catalyzed Tandem Isomerization-Hydroformylation of 10-Undecenitrile: Evidence for a Fast Isomerization Regime

Directory of Open Access Journals (Sweden)

Lucas Le Goanvic

2018-04-01

Full Text Available The tandem isomerization-hydroformylation of 10-undecenitrile (1 into the corresponding linear aldehyde (2 with a Rh-biphephos system was studied and the formation of internal olefin isomers (1-int-x was monitored over time. The existence of an “isomerization phenomenon” was evidenced, where fast isomerization of 1 into up to 70% of 1-int-x followed by fast back-isomerization of 1-int-x into 1 and, in turn, into 2 occurs. This fast dynamic isomerization regime is favored at high syngas pressure (40 bar and low biphephos-to-Rh ratio (5–10, and it is best observed at relatively high catalyst loadings ([1]0/[Rh] ≤ 3000. The latter regime is indeed evanescent, and gives place to a second stage in which isomerization of internal olefins (and eventual conversion into 2 proceeds much more slowly. The results are tentatively rationalized by the formation of an unstable species that promotes dynamic isomerization and which slowly vanishes or collapses into a Rh-biphephos species which is the one responsible for hydroformylation.

Investigation of the maximum load alleviation potential using trailing edge flaps controlled by inflow data

DEFF Research Database (Denmark)

Fischer, Andreas; Aagaard Madsen, Helge

2014-01-01

The maximum fatigue load reduction potential when using trailing edge flaps on mega-watt wind turbines was explored. For this purpose an ideal feed forward control algorithm using the relative velocity and angle of attack at the blade to control the loads was implemented. The algorithm was applied...... to time series from computations with the aeroelastic code HAWC2 and to measured time series. The fatigue loads could be reduced by 36% in the computations if the in flow sensor was at the same position as the blade load. The decrease of the load reduction potential when the sensor was at a distance from...... the blade load location was investigated. When the algorithm was applied to measured time series a load reduction of 23% was achieved which is still promissing, but significantly lower than the value achieved in computations....

Perspectives on the International and Internal Nuclear Security Regime

International Nuclear Information System (INIS)

Jang, Sung Soon

2015-01-01

The term, 'Nuclear Security' became more familiar to Korean public after the government hosted 2012 Seoul Nuclear Security Summit. Nuclear Security is prevention of, detection of and response to criminal or intentional unauthorized acts involving or directed at nuclear material, other radioactive material, associated facilities, or associated activities. Nuclear Security includes physical protection, security of radioactive sources, nuclear forensics, nuclear smuggling prevention, border monitoring, and cyber security with regard to nuclear and other radiological materials. This abstract will review recent international trends and discuss the nuclear security regime in the Republic of Korea (ROK). The international Nuclear Security Regime has been strengthened. The upcoming Chicago Summit in 2016 and the entry into force of the Amendment of Convention on Physical Protection of Nuclear Materials (CPPNM) will bring major changes in nuclear security. The Republic of Korea hosted the 2012 Seoul Summit and strengthened domestic regime to meet international standards. The ROK has worked hard to contribute to the international security regime and to establish a robust domestic security regime against terrorist threats. Even if the nuclear security regime is robust, Risk-informed Nuclear Security management should be established to meet international standards and to implement effective as well as an efficient nuclear security regime

Perspectives on the International and Internal Nuclear Security Regime

Energy Technology Data Exchange (ETDEWEB)

Jang, Sung Soon [Korea Nuclear Non-proliferation and Control, Daejeon (Korea, Republic of)

2015-10-15

The term, 'Nuclear Security' became more familiar to Korean public after the government hosted 2012 Seoul Nuclear Security Summit. Nuclear Security is prevention of, detection of and response to criminal or intentional unauthorized acts involving or directed at nuclear material, other radioactive material, associated facilities, or associated activities. Nuclear Security includes physical protection, security of radioactive sources, nuclear forensics, nuclear smuggling prevention, border monitoring, and cyber security with regard to nuclear and other radiological materials. This abstract will review recent international trends and discuss the nuclear security regime in the Republic of Korea (ROK). The international Nuclear Security Regime has been strengthened. The upcoming Chicago Summit in 2016 and the entry into force of the Amendment of Convention on Physical Protection of Nuclear Materials (CPPNM) will bring major changes in nuclear security. The Republic of Korea hosted the 2012 Seoul Summit and strengthened domestic regime to meet international standards. The ROK has worked hard to contribute to the international security regime and to establish a robust domestic security regime against terrorist threats. Even if the nuclear security regime is robust, Risk-informed Nuclear Security management should be established to meet international standards and to implement effective as well as an efficient nuclear security regime.

Dynamically-Loaded Hardware Libraries (HLL) Technology for Audio Applications

DEFF Research Database (Denmark)

Esposito, A.; Lomuscio, A.; Nunzio, L. Di

2016-01-01

In this work, we apply hardware acceleration to embedded systems running audio applications. We present a new framework, Dynamically-Loaded Hardware Libraries or HLL, to dynamically load hardware libraries on reconfigurable platforms (FPGAs). Provided a library of application-specific processors......, we load on-the-fly the specific processor in the FPGA, and we transfer the execution from the CPU to the FPGA-based accelerator. The proposed architecture provides excellent flexibility with respect to the different audio applications implemented, high quality audio, and an energy efficient solution....

Analysis of recurrent neural networks for short-term energy load forecasting

Science.gov (United States)

Di Persio, Luca; Honchar, Oleksandr

2017-11-01

Short-term forecasts have recently gained an increasing attention because of the rise of competitive electricity markets. In fact, short-terms forecast of possible future loads turn out to be fundamental to build efficient energy management strategies as well as to avoid energy wastage. Such type of challenges are difficult to tackle both from a theoretical and applied point of view. Latter tasks require sophisticated methods to manage multidimensional time series related to stochastic phenomena which are often highly interconnected. In the present work we first review novel approaches to energy load forecasting based on recurrent neural network, focusing our attention on long/short term memory architectures (LSTMs). Such type of artificial neural networks have been widely applied to problems dealing with sequential data such it happens, e.g., in socio-economics settings, for text recognition purposes, concerning video signals, etc., always showing their effectiveness to model complex temporal data. Moreover, we consider different novel variations of basic LSTMs, such as sequence-to-sequence approach and bidirectional LSTMs, aiming at providing effective models for energy load data. Last but not least, we test all the described algorithms on real energy load data showing not only that deep recurrent networks can be successfully applied to energy load forecasting, but also that this approach can be extended to other problems based on time series prediction.

The Failure Envelope Concept Applied To The Bone-Dental Implant System.