lng vehicle fuel: Topics by WorldWideScience.org

Sample records for lng vehicle fuel

LNG as vehicle fuel and the problem of supply: The Italian case study

International Nuclear Information System (INIS)

Arteconi, A.; Polonara, F.

2013-01-01

The transport sector represents a major item on the global balance of greenhouse gas (GHG) emissions. Natural gas is considered the alternative fuel that, in the short-medium term, can best substitute conventional fuels in order to reduce their environmental impact, because it is readily available at a competitive price, using technologies already in widespread use. It can be used as compressed gas (CNG) or in the liquid phase (LNG), being the former more suitable for light vehicles, while the latter for heavy duty vehicles. The purpose of this paper is to outline the potential of LNG as vehicle fuel, showing positive and negative aspects related to its introduction and comparing the different supply options with reference to the Italian scenario, paying particular attention to the possibility of on site liquefaction. The analysis has highlighted that purchasing LNG at the regasification terminal is convenient up to a terminal distance of 2000 km from the refuelling station. The liquefaction on site, instead, asks for liquefaction efficiency higher than 70% and low natural gas price and, as liquefaction technology, the let-down plants at the pressure reduction points along the pipeline are the best option to compete with direct supply at the terminal. -- Highlights: •LNG potential as vehicles fuel is analysed. •A SWOT analysis for LNG introduction in the Italian market is presented. •An economic comparison of different supply options is performed. •Possible micro-scale liquefaction technologies are evaluated
Life-cycle greenhouse gas analysis of LNG as a heavy vehicle fuel in Europe

International Nuclear Information System (INIS)

Arteconi, A.; Brandoni, C.; Evangelista, D.; Polonara, F.

2010-01-01

The aim of the present study was to compare the life cycle, in terms of greenhouse gas (GHG) emissions, of diesel and liquefied natural gas (LNG) used as fuels for heavy-duty vehicles in the European market (EU-15). A literature review revealed that the numerous studies conducted have reported different results when the authors departed from different baseline assumptions and reference scenarios. For our study, we concentrated on the European scenario and on heavy-duty road transport vehicles, given their important incidence on the global emissions of GHG. Two possible LNG procurement strategies were considered i.e. purchasing it directly from the regasification terminal (LNG-TER) or producing LNG locally (at the service station) with small-scale plants (LNG-SSL). We ascertained that the use of LNG-TER enables a 10% reduction in GHG emissions by comparison with diesel, while the emissions resulting from the LNG-SSL solution are comparable with those of diesel.
Life-cycle greenhouse gas analysis of LNG as a heavy vehicle fuel in Europe

Energy Technology Data Exchange (ETDEWEB)

Arteconi, A.; Brandoni, C.; Evangelista, D.; Polonara, F. [Universita Politecnica delle Marche, Dipartimento di Energetica, Via Brecce Bianche, 1-60131 Ancona (Italy)

2010-06-15

The aim of the present study was to compare the life cycle, in terms of greenhouse gas (GHG) emissions, of diesel and liquefied natural gas (LNG) used as fuels for heavy-duty vehicles in the European market (EU-15). A literature review revealed that the numerous studies conducted have reported different results when the authors departed from different baseline assumptions and reference scenarios. For our study, we concentrated on the European scenario and on heavy-duty road transport vehicles, given their important incidence on the global emissions of GHG. Two possible LNG procurement strategies were considered i.e. purchasing it directly from the regasification terminal (LNG-TER) or producing LNG locally (at the service station) with small-scale plants (LNG-SSL). We ascertained that the use of LNG-TER enables a 10% reduction in GHG emissions by comparison with diesel, while the emissions resulting from the LNG-SSL solution are comparable with those of diesel. (author)
White paper: Preliminary assessment of LNG vehicle technology, economics, and safety issues (Revision 1). Topical report, April-August 1991

International Nuclear Information System (INIS)

Powars, C.; Lucher, D.; Moyer, C.; Browning, L.

1992-01-01

The objective of the study is to evaluate the potential of LNG as a vehicle fuel, to determine market niches, and to identify needed technology improvements. The white paper is being issued when the work is approximately 30 percent complete to preview the study direction, draw preliminary conclusions, and make initial recommendations. Interim findings relative to LNG vehicle technology, economics, and safety are presented. It is important to decide if heavier hydrocarbons should be allowed in LNG vehicle fuel. Development of suitable refueling couplings and vehicle fuel supply pressure systems are recommended. Initial economics analyses considered transit buses and pickup and delivery trucks fueled via onsite liquefiers and imported LNG. Net user costs were more than (but in some cases close to) those for diesel fuel and gasoline. Lowering the cost of small-scale liquefiers would significantly improve the economics of LNG vehicles. New emissions regulations may introduce considerations beyond simple cost comparisons. LNG vehicle safety and available accident data are reviewed. Consistent codes for LNG vehicles and refueling facilities are needed
LNG -- Technology on the edge

International Nuclear Information System (INIS)

Alexander, C.B.

1995-01-01

With immense promise and many supporters, LNG as a vehicular fuel is still, a nascent industry. In about two years, an array of LNG engines should be commercially available, and infrastructure greatly expanded. These developments should reduce the present premium of LNG equipment, greatly improving industry economics. The most propitious sign for LNG-market developed lies in the natural gas industry's recently refined strategy for natural gas vehicles. The new strategy targets the right competitor--diesel, not gasoline. It also targets the right market for an emerging fuel--high-fuel-usage fleets made up of medium- and heavy-duty vehicles, often driven long distances. But problems persist in critical areas of development. These problems are related to the materials handling of LNG and the refueling of vehicles. The paper discusses the studies on LNG handling procedures, its performance benefits to high-fuel use vehicles, economic incentives for its use, tax disadvantages that are being fought, and LNG competition with ''clean'' diesel fuels
Coordination of ministerial actions regarding the use of liquefied natural gas (LNG) as fuel. LNG, a European component of the energy transition in road freight transport

International Nuclear Information System (INIS)

Maler, Philippe; Erhardt, Jean-Bernard; Ourliac, Jean-Paul

2015-09-01

This report is the third of a series dealing with the coordination of ministerial actions in favor of the use of liquefied natural gas (LNG) as fuel in transports. LNG is an important potential substitute to diesel fuel in road transport and would allow significant abatement of nitrogen oxides emissions. Bio-LNG is ten times less polluting than fossil fuel LNG and thus important efforts are to be made in bio-LNG R and D. An important work has been carried out for adapting EU regulations and standards to LNG vehicles and LNG supply developments. This report presents, first, a summary of the report's recommendations and the aim of this coordination study, and, then, treats more thoroughly of the different coordination aspects: 1 - European framework of energy transition in the road freight transport (differences with maritime transport, CO 2 emissions abatement, trucks pollution and fuel quality standards, trucks technical specifications and equipment, fuel taxes in EU countries); 2 - European policy and national actions in favour of LNG development for road transport (LNG as alternate fuel, the Paris agreement, the French national energy plan); 3 - Environmental benefits of LNG in road transport (public health impacts, nitrogen oxides abatement, divergent views and expertise, LNG and CO 2 abatement measures, bio-LNG environmental evaluation; 4 - LNG development actors in road transport and the administrative coordination (professional organizations, public stakeholders, LNG topics information dissemination at the Ministry); 5 - LNG development in road transport at the worldwide, European and national scales; 6 - European regulations and standards allowing trucks LNG fueling and circulation (standard needs, users information, regulation works); 7 - Common rules to define and implement for personnel training; 8 - reflexion on LNG taxation; 9 - support policy for a road transport LNG supply chain (infrastructures, European financing, lessons learnt from maritime
Methane as a Vehicle Fuel in Europe

International Nuclear Information System (INIS)

Maedge, M.

2014-01-01

NGVA Europe is aware of the importance of the promotion of Natural Gas and biomethane as an important vehicle fuels in Europe. The European Commission has recently adopted the Clean Power for Transport package including a Directive for deployment of alternative fuels infrastructure for CNG and LNG. Currently, the Member States have to report in their National Policy Frameworks, in a period of 24 months, their natural gas filling station development plans and fuel strategy in the nearest future. The European Union has a new transport infrastructure policy that connects the continent between East and West, North and South (TEN-T) and alternatives fuels will be taken into consideration for reducing the CO2 emissions, improve the air quality in urban areas, reduce the dependence with oil and enhance the competitiveness of the European industry. All of these researches have to be focus in the Horizon 2020, in which clean vehicles with CNG and LNG will be used to create 'smart cities and communities'. For achieving this idea, we are involved in the LNG Blue Corridor Project to demonstrate that the LNG is a real alternative for medium and long distance transport through the creation of new fuel stations in different countries such as Spain, France or Portugal. (author).
A NEW METHOD FOR CHARACTERIZING THE KNOCK RESISTANCE OF LNG FUELS USED IN THE TRANSPORTATION MARKET

NARCIS (Netherlands)

Levinsky, Howard; Gersen, Sander; van Essen, Martijn; van Dijk, Gerco

2014-01-01

To ensure that the engines to be used in LNG-fueled vehicles are matched with the expected variations in fuel composition, the knock resistance of the fuel must be determined unambiguously. Rather than rely on empirical methods using gas mixtures and “standard” engines traditionally employed for
Design Optimization of a Low Pressure LNG Fuel Supply System

OpenAIRE

Nguyen, Kim

2015-01-01

In 2014 there were 50 liquefied natural gas (LNG) fuelled ships in operation and around 70 on order worldwide. LNG proves to emit less pollution and considering the present and future emission regulations and optimistic gas fuel prices, LNG would be a preferable option as a marine fuel. The number of LNG fuelled ships is therefore likely to increase significantly the next five to ten years. There are many ways to configure the fuel supply system. The fuel supply system consists of a tank,...
Analysis of temperature and pressure changes in liquefied natural gas (LNG) cryogenic tanks

Science.gov (United States)

Chen, Q.-S.; Wegrzyn, J.; Prasad, V.

2004-10-01

Liquefied natural gas (LNG) is being developed as a transportation fuel for heavy vehicles such as trucks and transit buses, to lessen the dependency on oil and to reduce greenhouse gas emissions. The LNG stations are properly designed to prevent the venting of natural gas (NG) from LNG tanks, which can cause evaporative greenhouse gas emissions and result in fluctuations of fuel flow and changes of fuel composition. Boil-off is caused by the heat added into the LNG fuel during the storage and fueling. Heat can leak into the LNG fuel through the shell of tank during the storage and through hoses and dispensers during the fueling. Gas from tanks onboard vehicles, when returned to LNG tanks, can add additional heat into the LNG fuel. A thermodynamic and heat transfer model has been developed to analyze different mechanisms of heat leak into the LNG fuel. The evolving of properties and compositions of LNG fuel inside LNG tanks is simulated. The effect of a number of buses fueled each day on the possible total fuel loss rate has been analyzed. It is found that by increasing the number of buses, fueled each day, the total fuel loss rate can be reduced significantly. It is proposed that an electric generator be used to consume the boil-off gas or a liquefier be used to re-liquefy the boil-off gas to reduce the tank pressure and eliminate fuel losses. These approaches can prevent boil-off of natural gas emissions, and reduce the costs of LNG as transportation fuel.
Qualitative Risk Assessment for an LNG Refueling Station and Review of Relevant Safety Issues

Energy Technology Data Exchange (ETDEWEB)

Siu, N.; Herring, J.S.; Cadwallader, L.; Reece, W.; Byers, J.

1998-02-01

This report is a qualitative assessment of the public and worker risk involved with the operation of a liquefied natural gas (LNG) vehicle refueling facility. This study includes facility maintenance and operations, tank truck deliveries, and end-use vehicle fueling; it does not treat the risks of LNG vehicles on roadways. Accident initiating events are identified by using a Master Logic Diagram, a Failure Modes and Effects Analysis, and historical operating experiences. The event trees were drawn to depict possible sequences of mitigating events following the initiating events. The phenomenology of LNG and other vehicle fuels is discussed to characterize the hazard posed by LNG usage. Based on the risk modeling and analysis, recommendations are given to improve the safety of LNG refueling stations in the areas of procedures and training, station design, and the dissemination of ``best practice`` information throughout the LNG community.
Interim qualitative risk assessment for an LNG refueling station and review of relevant safety issues

Energy Technology Data Exchange (ETDEWEB)

Siu, N.; Herring, S.; Cadwallader, L.; Reece, W.; Byers, J.

1997-07-01

This report is a qualitative assessment of the public and worker risk involved with the operation of a liquefied natural (LNG) vehicle refueling facility. This study includes facility maintenance and operations, tanker truck delivers and end-use vehicle fueling; it does not treat the risks of LNG vehicles on roadways. Accident initiating events are identified by using a Master Logic Diagram, a Failure Modes and Effects analysis and historical operating experiences. The event trees were drawn to depict possible sequences of mitigating events following the initiating events. The phenomenology of LNG and other vehicle fuels is discussed to characterize the hazard posed by LNG usage. Based on the risk modeling and analysis, recommendations are given to improve the safety of LNG refueling stations in the areas of procedures and training, station design, and the dissemination of best practice information throughout the LNG community.
[Fuel substitution of vehicles by natural gas: Summaries of four final technical reports

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

This report contains summary information on three meetings and highlights of a fourth meeting held by the Society of Automotive Engineers on natural gas fueled vehicles. The meetings covered the following: Natural gas engine and vehicle technology; Safety aspects of alternately fueled vehicles; Catalysts and emission control--Meeting the legislative standards; and LNG--Strengthening the links.
Study on Calculation of Liquid Level And Storage of Tanks for LNG-fueled Vessels

Science.gov (United States)

Li, Kun; Wang, Guoqing; Liu, Chang

2018-01-01

As the ongoing development of the application of LNG as a clean energy in waterborne transport industry, the fleet scale of LNG-fueled vessels enlarged and the safety operation has attracted more attention in the industry. Especially the accurate detection of liquid level of LNG tanks is regarded as an important issue to ensure a safe and stable operation of LNG-fueled ships and a key parameter to keep the proper functioning of marine fuel storage system, supply system and safety control system. At present, detection of LNG tank liquid level mainly adopts differential pressure detection method. Liquid level condition could be found from the liquid level reference tables. However in practice, since LNG-fueled vessels are generally not in a stationary state, liquid state within the LNG tanks will constantly change, the detection of storage of tanks only by reference to the tables will cause deviation to some extent. By analyzing the temperature under different pressure, the effects of temperature change on density and volume integration calculation, a method of calculating the liquid level and storage of LNG tanks is put forward making the calculation of liquid level and actual storage of LNG tanks more accurately and providing a more reliable basis for the calculation of energy consumption level and operation economy for LNG-fueled vessels.
Life Cycle Greenhouse Gas Analysis of Multiple Vehicle Fuel Pathways in China

Directory of Open Access Journals (Sweden)

Tianduo Peng

2017-11-01

Full Text Available The Tsinghua University Life Cycle Analysis Model (TLCAM is applied to calculate the life cycle fossil energy consumption and greenhouse gas (GHG emissions for more than 20 vehicle fuel pathways in China. In addition to conventional gasoline and diesel, these include coal- and gas-based vehicle fuels, and electric vehicle (EV pathways. The results indicate the following. (1 China’s current dependence on coal and relative low-efficiency processes limits the potential for most alternative fuel pathways to decrease energy consumption and emissions; (2 Future low-carbon electricity pathways offer more obvious advantages, with coal-based pathways needing to adopt carbon dioxide capture and storage technology to compete; (3 A well-to-wheels analysis of the fossil energy consumption of vehicles fueled by compressed natural gas and liquefied natural gas (LNG showed that they are comparable to conventional gasoline vehicles. However, importing rather than domestically producing LNG for vehicle use can decrease domestic GHG emissions by 35% and 31% compared with those of conventional gasoline and diesel vehicles, respectively; (4 The manufacturing and recovery of battery and vehicle in the EV analysis has significant impact on the overall ability of EVs to decrease fossil energy consumption and GHG emissions from ICEVs.
Concept for a LNG Gas Handling System for a Dual Fuel Engine

Directory of Open Access Journals (Sweden)

Michael Rachow

2017-09-01

Full Text Available Nowadays, ships are using LNG as main engine fuel because based on the facts that LNG has no sulphur content, and its combustion process, LNG produces low NOx content compared to heavy fuel oil and marine diesel oil. LNG is not only produces low gas emission, but may have economic advantages. In the engine laboratory of maritime studies department in Warnemunde, Germany, there is a diesel engine type MAN 6L23/30 A, where the mode operation of these engine would be changed to dual fuel engine mode operation. Therefore, in this thesis, the use dual fuel engine will be compared where it will utilize natural gas and marine diesel oil and select the required components for fuel gas supply system. By conducting the process calculation, engine MAN 6L23/30 A requires the capacity natural gas of 12.908 for 5 days at full load. A concept for LNG supply system would be arranged from storage tank until engine manifold. Germanischer Lloyd and Project Guide of dual fuel engine will be used as a guidelines to develop an optimal design and arrangement which comply with the regulation.
The globalization and environmental sustainability of LNG: Is LNG a fuel for the 21st century?

Energy Technology Data Exchange (ETDEWEB)

Sakmar, Susan

2010-09-15

As the world enters the 21st Century, policy makers around the world are grappling with issues related to energy security, energy poverty, global climate change, and the need to reduce greenhouse gas emissions while meeting an expected increase in demand for all energy sources. As a clean burning fuel, many policy leaders have suggested that LNG can play an important role as the world struggles to develop a more environmental sustainable energy future. Others claim that the safety and environmental impact of LNG, including life-cycle emissions, may nullify any clean burning benefit LNG might otherwise provide.
USING OF NON-CONVENTIONAL FUELS IN HYBRID VEHICLE DRIVES

Directory of Open Access Journals (Sweden)

Dalibor Barta

2016-12-01

Full Text Available Electric or hybrid vehicles are becoming increasingly common on roads. While electric vehicles are still more or less intended for city traffic, hybrid vehicles allow normal use due to wider driving range. The use of internal combustion engines in hybrid drives is still an inspiration to find the way to reduce the produc-tion of emissions. Numbers of alternative energy resources were studied as a substitution of conventional fuels for hybrid vehicles drives worldwide. The paper deals with the possibility of using alternative fuels as CNG, LPG and LNG in combination with hybrid drive of a midibus with the capacity of 20 passengers. Various aspects and techniques of hybrid vehicles from energy management system, propulsion system and using of various alternative fuels are explored in this paper. Other related fields of hybrid vehicles such as changes of vehicle weight or influence of electric energy sources on the total vehicle emission production are also included.
LNG plants in the US and abroad

International Nuclear Information System (INIS)

Blazek, C.F.; Biederman, R.T.

1992-01-01

The Institute of Gas Technology recently conducted a comprehensive survey of LNG production and storage facilities in North America. This survey was performed as part of IGT's LNG Observer newsletter which covers both domestic and international LNG news, reports on LNG related economics and statistics, and routinely conducts interviews with key industry leaders. In addition to providing consulting services to the LNG industry, IGT has cosponsored the International Conference on Liquefied Natural Gas for the part 20 years. The objective of this paper is to present a summary of our recent survey results as well as provide an overview of world LNG trade. This information is important in assessing the potential near term availability of LNG for transportation applications. The IGT LNG Survey appraised the capacity and current market activity of LNG peak shaving, satellite storage, and import receiving facilities in the United States and Canada. Information was requested from facilities on three main topics: liquefaction, storage, and regasification. Additional questions were posed regarding the year of operation, designer/contractor for liquefaction cycle and storage, source of LNG (for storage-only facilities), plans for expansion, and level of interest in providing LNG as a vehicle fuel. The IGT LNG Survey has to date received information on 56 LNG peak shaving facilities, 28 satellite storage facilities, and 4 LNG import receiving terminals
Review and analysis of potential safety impacts of and regulatory barriers to fuel efficiency technologies and alternative fuels in medium- and heavy-duty vehicles

Science.gov (United States)

2015-06-01

This report summarizes a safety analysis of medium- and heavy-duty vehicles (MD/HDVs) equipped with fuel efficiency (FE) technologies and/or using alternative fuels (natural gas-CNG and LNG, propane, biodiesel and power train electrification). The st...

LNG - Status in Denmark. Technology and potential. Project report

Energy Technology Data Exchange (ETDEWEB)

Naeslund, M.

2012-05-15

The interest for LNG both on a small and a large scale is increasing worldwide. The experiences and knowledge on LNG is limited in Denmark. The Danish gas companies' Technical Management Group (TCG) has asked for a status report including a technology description and an evaluation of the potential in Denmark. A survey of primarily small-scale LNG technology is done in the report. The focus is motivated by the new areas of gas utilisation that become possible with small-scale LNG. Small-scale LNG in this study is defined as LNG stored and used at the application or in an isolated gas grid. The small-scale use of LNG has today an almost negligible share of the total LNG trade but offers interesting new applications for gas utilisation. LNG on a small scale can be used primarily as: 1) Ship fuel. 2) Truck fuel (heavy duty long distance). 3) Individual users not connected to the natural gas grid. 4) Backup for upgraded biogas to individual users and vehicle fleets. 5) Security of supply or supply enhancement of heavily loaded parts of the gas grid. 6) Small-scale storage and/or peak shaving. All but the first topics are natural uses for the current Danish gas distributors. LNG as ship fuel may engage other specialized LNG companies. The report contains a technical description of the parts in primarily small-scale LNG handling and operation. Liquefaction, transport, storage, engine technologies, gas quality and safety aspects related to LNG are covered. There seem to be two more or less separate paths for LNG in Denmark, onshore and off-shore use. These are not, apparently, sharing their experiences and knowledge. Rules and regulations are also different which may create some problems in the interface, for example ship bunkering. Further studies are suggested in the area of gas quality and engine technologies and adaptation of foreign guidelines for small-scale installations to Danish conditions. These guidelines ought to be based on international standards and
Exergetic Analysis, Optimization and Comparison of LNG Cold Exergy Recovery Systems for Transportation

Directory of Open Access Journals (Sweden)

Paweł Dorosz

2018-01-01

Full Text Available LNG (Liquefied Natural Gas shares in the global energy market is steadily increasing. One possible application of LNG is as a fuel for transportation. Stricter air pollution regulations and emission controls have made the natural gas a promising alternative to liquid petroleum fuels, especially in the case of heavy transport. However, in most LNG-fueled vehicles, the physical exergy of LNG is destroyed in the regasification process. This paper investigates possible LNG exergy recovery systems for transportation. The analyses focus on “cold energy” recovery systems as the enthalpy of LNG, which may be used as cooling power in air conditioning or refrigeration. Moreover, four exergy recovery systems that use LNG as a low temperature heat sink to produce electric power are analyzed. This includes single-stage and two-stage direct expansion systems, an ORC (Organic Rankine Cycle system, and a combined system (ORC + direct expansion. The optimization of the above-mentioned LNG power cycles and exergy analyses are also discussed, with the identification of exergy loss in all components. The analyzed systems achieved exergetic efficiencies in the range of 20 % to 36 % , which corresponds to a net work in the range of 214 to 380 kJ/kg L N G .
Designing Optimal LNG Station Network for U.S. Heavy-Duty Freight Trucks using Temporally and Spatially Explicit Supply Chain Optimization

Science.gov (United States)

Lee, Allen

The recent natural gas boom has opened much discussion about the potential of natural gas and specifically Liquefied Natural Gas (LNG) in the United States transportation sector. The switch from diesel to natural gas vehicles would reduce foreign dependence on oil, spur domestic economic growth, and potentially reduce greenhouse gas emissions. LNG provides the most potential for the medium to heavy-duty vehicle market partially due to unstable oil prices and stagnant natural gas prices. As long as the abundance of unconventional gas in the United States remains cheap, fuel switching to natural gas could provide significant cost savings for long haul freight industry. Amid a growing LNG station network and ever increasing demand for freight movement, LNG heavy-duty truck sales are less than anticipated and the industry as a whole is less economic than expected. In spite of much existing and mature natural gas infrastructure, the supply chain for LNG is different and requires explicit and careful planning. This thesis proposes research to explore the claim that the largest obstacle to widespread LNG market penetration is sub-optimal infrastructure planning. No other study we are aware of has explicitly explored the LNG transportation fuel supply chain for heavy-duty freight trucks. This thesis presents a novel methodology that links a network infrastructure optimization model (represents supply side) with a vehicle stock and economic payback model (represents demand side). The model characterizes both a temporal and spatial optimization model of future LNG transportation fuel supply chains in the United States. The principal research goal is to assess the economic feasibility of the current LNG transportation fuel industry and to determine an optimal pathway to achieve ubiquitous commercialization of LNG vehicles in the heavy-duty transport sector. The results indicate that LNG is not economic as a heavy-duty truck fuel until 2030 under current market conditions
Preconditions for the development of land-based infrastructure for liquefied natural gas (LNG / LBG); Foerutsaettningar foer utbyggnad av landbaserad infrastruktur foer flytande gas (LNG/LBG)

Energy Technology Data Exchange (ETDEWEB)

Stenkvist, Maria; Paradis, Hanna; Haraldsson, Kristina; Beijer, Ronja; Stensson, Peter (AaF Industry AB(Sweden))

2011-06-15

The conversion potential to replace oil in the energy intensive industries and diesel in heavy transport is estimated in the study to 6.8 TWh and 10 TWh per year, respectively. Several alternative fuels compete for this conversion potential. What fuels will take market share depends on several factors such as price, availability of fuel, availability of process technology and vehicles, technology development and possible future technological advances. For liquid methane to compete a new infrastructure is required that in a cost effective manner makes it possible to distribute the liquid methane to the regions where the need is the greatest. With today's distribution system, including truck delivery from import terminals in Nynaeshamn and Fredrikstad, virtually the entire southern Sweden is within reach of LNG deliveries. The study points out three nodes, Gaevle, Sundsvall and Luleaa, which is suitable for distribution of liquid methane to the central and northern Sweden. The three hubs are suitable for freight transfer to trucks as well as rail and shipping. A strategic nationwide network of refueling stations is also proposed, with a total of 18 new stations, in addition to the filling stations in southern and central Sweden that are already planned or in operation. Both the availability and use of liquid methane in Sweden today is limited. Liquid natural gas, LNG (liquefied natural gas), is primarily used as a backup to biogas plants, in a few industries and as supply for a few filling stations for compressed gas. The availability of LNG and also liquid biogas (LBG liquefied biogas), will increase in coming years. In 2011, two new LNG import terminals are put into operation in Nynaeshamn and Fredrikstad in Norway and two additional import terminals are planned in Gothenburg and Lysekil. Furthermore, two production plants for liquid biogas production have started, and four additional plants are planned, which together will produce around 0.5 TWh LBG annually
Increasing efficiency of TPP fuel suply system due to LNG usage as a reserve fuel

Science.gov (United States)

Zhigulina, E. V.; Khromchenkov, V. G.; Mischner, J.; Yavorovsky, Y. V.

2017-11-01

The paper is devoted to the analysis of fuel economy efficiency increase possibility at thermal power plants (TPP) due to the transition from the use of black oil as a reserve fuel to liquefied natural gas (LNG) produced at the very station. The work represents the technical solution that allows to generate, to store and to use LNG as the reserve fuel TPP. The annual amounts of black oil and natural gas that are needed to ensure the reliable operation of several power plants in Russia were assessed. Some original schemes of the liquefied natural gas production and storing as alternative reserve fuel generated by means of application of expansion turbines are proposed. The simulation results of the expansion process for two compositions of natural gas with different contents of high-boiling fractions are presented. The dependences of the condensation outlet and power generation from the flow initial parameters and from the natural gas composition are obtained and analysed. It was shown that the choice of a particular circuit design depends primarily on the specific natural gas composition. The calculations have proved the effectiveness and the technical ability to use liquefied natural gas as a backup fuel at reconstructed and newly designed gas power station.
Low-Cost Methane Liquefaction Plant and Vehicle Refueling Station

International Nuclear Information System (INIS)

Wilding, B.; Bramwell, D.

1999-01-01

The Idaho National Engineering and Environmental Laboratory (INEEL) is currently negotiating a collaborative effort with Pacific Gas and Electric (PG and E) that will advance the use of liquefied natural gas (LNG) as a vehicle fuel. We plan to develop and demonstrate a small-scale methane liquefaction plant (production of 5,000 to 10,000 gallons per day) and a low-cost ($150,000) LNG refueling station to supply fuel to LNG-powered transit buses and other heavy-duty vehicles. INEEL will perform the research and development work. PG and E will deploy the new facilities commercially in two demonstration projects, one in northern California, and one in southern California
LNG in transportation

International Nuclear Information System (INIS)

Madden, Mike; White, Nick; Le Fevre, Chris

2014-01-01

This document summarizes the content of a 402 p. study published by CEDIGAZ, the International Center for Natural Gas Information. According to this study, LNG as a fuel will capture a significant market share in the transport sector by 2035. The greatest potential is seen in road transport, were annual demand is projected to reach 96 million tons per year (mtpa) in CEDIGAZ' base scenario while demand in the marine sector could grow to an estimated 77 mtpa. The rail sector could add another 6 mtpa to global demand. However, the development of LNG as a transport fuel faces a number of challenges, and will have to go hand in hand with the development of fueling infrastructure
The development of natural gas as an automotive fuel in China

International Nuclear Information System (INIS)

Ma, Linwei; Geng, Jia; Li, Weqi; Liu, Pei; Li, Zheng

2013-01-01

This manuscript aims to systematically review the development of natural gas as an automotive fuel in China and to draw policy implications for decision making. This manuscript presents a brief overview of natural gas development and the potential of natural gas as an automotive fuel in China, followed by an introduction to the development of various technology pathways for using natural gas as an automotive fuel, including CNG (compressed natural gas) vehicles, LNG (liquefied natural gas) vehicles, and others. This material suggests, a large potential to increase the use of natural gas as an automotive fuel, especially for CNG and LNG vehicles. The following activities will promote the development of natural gas vehicles: prioritizing vehicle use in the utilization of natural gas, supporting the construction of natural gas filling stations, developing a favorable pricing policy for natural gas used in vehicles, and enhancing the research and development to further improve the technology performance, especially for the technology of LNG vehicles. -- Highlights: •An overview of the natural gas development in China. •A systematic introduction of the development of natural gas vehicles in China. •A review of the technological performance of natural gas vehicles. •Policy suggestions to promote the development of natural gas vehicles in China
LNG as a marine and inland waterway fuel. Contribution of AFG (French gas association) to the national policy framework for the deployment of alternative fuel infrastructures (AFNPF)

International Nuclear Information System (INIS)

2016-06-01

Here in the early 21. Century, the environmental footprint of marine and inland waterway transport is a major concern on a global scale. Under the authority of the International Maritime Organisation (IMO), regulations on atmospheric emissions are becoming increasingly tighter. The European Union (EU) is deeply committed to this endeavour and in particular has adopted Directive 2014/94/EU which aims to facilitate the deployment of an alternative fuels infrastructure. The Directive calls upon Member States to develop by 18 November 2016, national policy frameworks for the deployment of alternative fuel infrastructures (AFNPF) that must designate an appropriate number of LNG refuelling points in maritime and inland ports for maritime and inland waterway transport purposes. In light of this, the French Gas Association (AFG), in cooperation with all affected stakeholders and interested parties, has discussed the role of LNG as a marine and inland waterway fuel in the energy transition toward green growth, in order to contribute to the development of France's 'national policy framework' (AFNPF) under the Directive mentioned above. To assess the prospects of the LNG bunkering market in France, as well as the implementation of the corresponding infrastructures, the AFG adopted a scenario-based approach from the user's perspective. Considering that we are in an early stage, the study focuses on the types of ships that are most likely to use LNG, and it examines their traffic in France's major metropolitan ports, along with forecasted activity based on the strategic plans for those ports. Two scenarios - one being rather conservative (baseline) and the other being more optimistic - were examined over three timelines: 2020, 2025 and 2030. The scenarios lead to a gradual implementation of LNG fuel in French ports, on the three coastlines and along the five inland waterway corridors. They show LNG fuel needs in all the ports of the central TEN
Assessment of institutional barriers to the use of natural gas fuel in automotive vehicle fleets

Science.gov (United States)

Jablonski, J.; Lent, L.; Lawrence, M.; White, L.

1983-01-01

Institutional barriers to the use of natural gas as a fuel for motor vehicle fleets were identified. Recommendations for barrier removal were developed. Eight types of institutional barriers were assessed: (1) lack of a national standard for the safe design and certification of natural gas vehicles and refueling stations; (2) excessively conservative or misapplied state and local regulations, including bridge and tunnel restrictions, restrictions on types of vehicles that may be fueled by natural gas, zoning regulations that prohibit operation of refueling stations, parking restrictions, application of LPG standards to LNG vehicles, and unintentionally unsafe vehicle or refueling station requirements; (3) need for clarification of EPA's tampering enforcement policy; (4) the U.S. hydrocarbon standard; (5) uncertainty concerning state utility commission jurisdiction; (6) sale for resale prohibitions imposed by natural gas utility companies or state utility commissions; (7) uncertainty of the effects of conversions to natural gas on vehicle manufactures warranties; and (8) need for a natural gas to gasoline equivalent units conversion factor for use in calculation of state road use taxes.
The Safety Design Research of a LNG Carrier Vehicle

OpenAIRE

Liang, Yi; Zhou, Xiang

2015-01-01

LNG is the abbreviation for liquefied natural gas, which is recognized as one of the world’s clean energies. LNG is one product at natural gas that through purification and ultra-low temperature is liquefied. The liquefied natural gas is very suitable for LNG transportation by a truck. China is a big country rich in natural resources. The use of natural gas is in favor of Chinese energy structure adjustment. It has important strategic significance to improve the ecological environment and the...
Retail LNG handbook. Retail LNG and The Role of LNG Import Terminals. Report by the GIIGNL Technical Study Group on the possible role of LNG import terminals within the emerging Retail LNG Market

International Nuclear Information System (INIS)

2015-01-01

The natural gas and liquefied natural gas (LNG) industries are changing. The influx of supply, low prices, and environmental benefits of natural gas are driving consumers to convert from other fossil fuels. Natural gas consumers on pipeline systems have the ability to benefit, but for those not connected, LNG may be the only opportunity to convert to natural gas. As this market evolves, a unique opportunity may emerge for some existing participants in the LNG market and could lead to a shift in business focus, potentially adding to or even transforming the traditional role of LNG Import Terminals. As surmised by the GIIGNL's Technical Study Group (TSG) at the outset of their endeavor, virtually every member company had historical experience with, was in the midst of expanding its services to include, or was actively engaged in the study of, Retail LNG. The market drivers, value propositions, trends and future prospects for Retail LNG that have widely been publicized were generally confirmed although in an overall more conservative outlook. As a representative body of experienced, long term LNG Import Terminal operators, GIIGNL was uniquely qualified to stress in its Handbook the importance of managing the inherent risk associated with LNG, the application of suitable codes and standards and the use of proper equipment. The study of the aspects of LNG supply and use including safety, security, staffing, equipment siting, and operations is hoped to provide an illustrative framework form which the industry can jointly move towards best practices. While Retail LNG is considered by many to be 'new' there is substantial historical experience with all aspects of the market. LNG Import Terminals, including the experience and competence of their staffing, can play a key role in not only the incubation and growth of the Retail market, but the molding and shaping of regulatory framework, applicable codes and standards and operational best practices. GIIGNL
Liquefied natural gas as a transportation fuel for heavy-duty trucks: Volume I

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

This document contains Volume 1 of a three-volume manual designed for use with a 2- to 3-day liquefied natural gas (LNG) training course. Transportation and off-road agricultural, mining, construction, and industrial applications are discussed. This volume provides a brief introduction to the physics and chemistry of LNG; an overview of several ongoing LNG projects, economic considerations, LNG fuel station technology, LNG vehicles, and a summary of federal government programs that encourage conversion to LNG.
Guidance on Biogas used to Produce CNG or LNG under the Renewable Fuel Standard Program

Science.gov (United States)

Provides EPA’s interpretation of biogas quality and RIN generation requirements that apply to renewable fuel production pathways involving the injection into a commercial pipeline of biogas for use in producing renewable CNG or renewable LNG.
LNG plant combined with power plant

Energy Technology Data Exchange (ETDEWEB)

Aoki, I; Kikkawa, Y [Chiyoda Chemical Engineering and Construction Co. Ltd., Tokyo (Japan)

1997-06-01

The LNG plant consumers a lot of power of natural gas cooling and liquefaction. In some LNG plant location, a rapid growth of electric power demand is expected due to the modernization of area and/or the country. The electric power demand will have a peak in day time and low consumption in night time, while the power demand of the LNG plant is almost constant due to its nature. Combining the LNG plant with power plant will contribute an improvement the thermal efficiency of the power plant by keeping higher average load of the power plant, which will lead to a reduction of electrical power generation cost. The sweet fuel gas to the power plant can be extracted from the LNG plant, which will be favorable from view point of clean air of the area. (Author). 5 figs.
LNG plant combined with power plant

International Nuclear Information System (INIS)

Aoki, I.; Kikkawa, Y.

1997-01-01

The LNG plant consumers a lot of power of natural gas cooling and liquefaction. In some LNG plant location, a rapid growth of electric power demand is expected due to the modernization of area and/or the country. The electric power demand will have a peak in day time and low consumption in night time, while the power demand of the LNG plant is almost constant due to its nature. Combining the LNG plant with power plant will contribute an improvement the thermal efficiency of the power plant by keeping higher average load of the power plant, which will lead to a reduction of electrical power generation cost. The sweet fuel gas to the power plant can be extracted from the LNG plant, which will be favorable from view point of clean air of the area. (Author). 5 figs
LANDFILL GAS CONVERSION TO LNG AND LCO{sub 2}. PHASE 1, FINAL REPORT FOR THE PERIOD MARCH 1998-FEBRUARY 1999

Energy Technology Data Exchange (ETDEWEB)

COOK,W.J.; NEYMAN,M.; SIWAJEK,L.A.; BROWN,W.R.; VAN HAUWAERT,P.M.; CURREN,E.D.

1998-02-25

Process designs and economics were developed to produce LNG and liquid carbon dioxide (CO{sub 2}) from landfill gas (LFG) using the Acrion CO{sub 2} wash process. The patented Acrion CO{sub 2} wash process uses liquid CO{sub 2} to absorb contaminants from the LFG. The process steps are compression, drying, CO{sub 2} wash contaminant removal and CO{sub 2} recovery, residual CO{sub 2} removal and methane liquefaction. Three flowsheets were developed using different residual CO{sub 2} removal schemes. These included physical solvent absorption (methanol), membranes and molecular sieves. The capital and operating costs of the flowsheets were very similar. The LNG production cost was around ten cents per gallon. In parallel with process flowsheet development, the business aspects of an eventual commercial project have been explored. The process was found to have significant potential commercial application. The business plan effort investigated the economics of LNG transportation, fueling, vehicle conversion, and markets. The commercial value of liquid CO{sub 2} was also investigated. This Phase 1 work, March 1998 through February 1999, was funded under Brookhaven National laboratory contract 725089 under the research program entitled ``Liquefied Natural Gas as a Heavy Vehicle Fuel.'' The Phase 2 effort will develop flowsheets for the following: (1) CO{sub 2} and pipeline gas production, with the pipeline methane being liquefied at a peak shaving site, (2) sewage digester gas as an alternate feedstock to LFG and (3) the use of mixed refrigerants for process cooling. Phase 2 will also study the modification of Acrion's process demonstration unit for the production of LNG and a market site for LNG production.
Vehicle technologies, fuel-economy policies, and fuel-consumption rates of Chinese vehicles

International Nuclear Information System (INIS)

Huo Hong; He Kebin; Wang, Michael; Yao Zhiliang

2012-01-01

One of the principal ways to reduce transport-related energy use is to reduce fuel-consumption rates of motor vehicles (usually measured in liters of fuel per 100 km). Since 2004, China has implemented policies to improve vehicle technologies and lower the fuel-consumption rates of individual vehicles. Policy evaluation requires accurate and adequate information on vehicle fuel-consumption rates. However, such information, especially for Chinese vehicles under real-world operating conditions, is rarely available from official sources in China. For each vehicle type we first review the vehicle technologies and fuel-economy policies currently in place in China and their impacts. We then derive real-world (or on-road) fuel-consumption rates on the basis of information collected from various sources. We estimate that the real-world fuel-consumption rates of vehicles in China sold in 2009 are 9 L/100 km for light-duty passenger vehicles, 11.4 L/100 km for light-duty trucks, 22 L/100 km for inter-city transport buses, 40 L/100 km for urban transit buses, and 24.9 L/100 km for heavy-duty trucks. These results aid in understanding the levels of fuel consumption of existing Chinese vehicle fleets and the effectiveness of policies in reducing on-road fuel consumption, which can help in designing and evaluating future vehicle energy-efficiency policies. - Highlights: ► Vehicle fuel-consumption rate (VFCR) data are rarely available in China. ► We review the fuel-economy policies currently in place in China and their impacts. ► We derive real-world VFCRs on the basis of information collected from various sources. ► Results aid in understanding the fuel consumption levels of Chinese vehicle fleets. ► Results help in designing and evaluating future vehicle energy-efficiency policies.
Assessment of methane-related fuels for automotive fleet vehicles: technical, supply, and economic assessments

Energy Technology Data Exchange (ETDEWEB)

1982-02-01

The use of methane-related fuels, derived from a variety of sources, in highway vehicles is assessed. Methane, as used here, includes natural gas (NG) as well as synthetic natural gas (SNG). Methanol is included because it can be produced from NG or the same resources as SNG, and because it is a liquid fuel at normal ambient conditions. Technological, operational, efficiency, petroleum displacement, supply, safety, and economic issues are analyzed. In principle, both NG and methanol allow more efficient engine operation than gasoline. In practice, engines are at present rarely optimized for NG and methanol. On the basis of energy expended from resource extraction to end use, only optimized LNG vehicles are more efficient than their gasoline counterparts. By 1985, up to 16% of total petroleum-based highway vehicle fuel could be displaced by large fleets with central NG fueling depots. Excluding diesel vehicles, which need technology advances to use NG, savings of 8% are projected. Methanol use by large fleets could displace up to 8% of petroleum-based highway vehicle fuel from spark-ignition vehicles and another 9% from diesel vehicles with technology advances. The US NG supply appears adequate to accommodate fleet use. Supply projections, future price differential versus gasoline, and user economics are uncertain. In many cases, attractive paybacks can occur. Compressed NG now costs on average about $0.65 less than gasoline, per energy-equivalent gallon. Methanol supply projections, future prices, and user economics are even more uncertain. Current and projected near-term methanol supplies are far from adequate to support fleet use. Methanol presently costs more than gasoline on an equal-energy basis, but is projected to cost less if produced from coal instead of NG or petroleum.
LNG links remote supplies and markets

International Nuclear Information System (INIS)

Avidan, A.A.; Gardner, R.E.; Nelson, D.; Borrelli, E.N.; Rethore, T.J.

1997-01-01

Liquefied natural gas (LNG) has established a niche for itself by matching remote gas supplies to markets that both lacked indigenous gas reserves and felt threatened in the aftermath of the energy crises of the 1970s and 1980s. It has provided a cost-effective energy source for these markets, while also offering an environmentally friendly fuel long before that was fashionable. The introduction of natural-gas use via LNG in the early years (mostly into France and Japan) has also allowed LNG to play a major role in developing gas infrastructure. Today, natural gas, often supplied as LNG, is particularly well-suited for use in the combined cycle technology used in independent power generation projects (IPPs). Today, LNG players cannot simply focus on monetizing gas resources. Instead, they must adapt their projects to meet the needs of changing markets. The impact of these changes on the LNG industry has been felt throughout the value chain from finding and producing gas, gas treatment, liquefaction, transport as a liquid, receiving terminals and regasification, and finally, to consumption by power producers, industrial users, and households. These factors have influenced the evolution of the LNG industry and have implications for the future of LNG, particularly in the context of worldwide natural gas

DoD use of Domestically-Produced Alternative Fuels and Alternative Fuel Vehicles

Science.gov (United States)

2014-04-10

85 $21,927 Electric $171 Hydrogen $3 Liquefied Natural Gas (LNG) $4 Liquefied Petroleum Gas ( LPG ) $14 Total $25,053 Data source: GSA’s FAST Data...919 407 5,802 GAS PH 13 77 94 10 10 204 HYD DE 5 5 LNG BI 1 1 LPG BI 47 47 LPG DE 1 1 Conventional DSL DE 867 16,174 16,028 5,698 2,508 41,275...includes information on the status of: (1) use and potential use of domestically-produced alternative fuels including but not limited to, natural gas
Power and LPG production with LNG import

International Nuclear Information System (INIS)

Mak, J.Y.

2004-01-01

When used in power cogeneration, Liquefied Natural Gas (LNG) is both energy efficient and can eliminate seawater or fuel gas consumption as well as the associated environmental impacts of conventional regasification processes. However, some liquefied natural gas (LNG) sources have heating values higher than current North American natural gas pipelines can allow for. LNG from these cannot be injected into gas pipelines without several heating control processing steps. This paper outlines two new technologies developed to address this issue. The first is a power cogeneration process using LNG as a heat sink. The second technology involves a fractionation process removing Liquid Propane Gas (LPG) components from imported LNG, thereby controlling heat value. Both technologies are applicable in grassroots installations as well as being suitable for retrofitting to existing LNG regasification for power generation and LPG production. It was concluded that power cogeneration with a mixed fluid power cycle recovered a significant portion of energy in LNG liquefaction plants. Additionally, it was also possible to fractionate high quality LPG from LNG at a low cost, with the residue being further re-condensed and re-utilized for power generation. It was also concluded that the LNG fractionation process would add flexibility to the LNG receiving terminals, allowing the import of lower quality LNG to North America, while also generating additional revenues from LPG production. 3 refs., 5 tabs., 6 figs
French Gas Association roundtable - May 27, 2013. Evolutions of the LNG market

International Nuclear Information System (INIS)

Robin, Jean-Yves; Brunero, Francois; Cotin, Pierre; Daubonne, Jean-Francois; Deybach, Frederic; Seilhan, Bruno

2013-01-01

The LNG industry is currently facing contrasting trends, with overall decreasing consumption in 2012 compared to the previous year, large uncertainties on gas prices - energy being regarded by European and Asian customers as costly - and however very encouraging prospects, in particular regarding LNG as a fuel. This document reports on the minutes of the French Gas Association roundtable on the subject 'Evolutions of the LNG market'. Contents: 1) LNG Market Outlook, 2) LNG in Europe, 3) LNG terminals and the evolving LNG market, 4) The road-transported LNG market, 5) LNG market trends, 6) Questions and Answers
Research on energy efficiency design index for sea-going LNG carriers

Science.gov (United States)

Lin, Yan; Yu, Yanyun; Guan, Guan

2014-12-01

This paper describes the characteristics of liquefied natural gas (LNG) carriers briefly. The LNG carrier includes power plant selection, vapor treatment, liquid cargo tank type, etc. Two parameters—fuel substitution rate and recovery of boil of gas (BOG) volume to energy efficiency design index (EEDI) formula are added, and EEDI formula of LNG carriers is established based on ship EEDI formula. Then, based on steam turbine propulsion device of LNG carriers, mathematical models of LNG carriers' reference line value are established in this paper. By verification, the EEDI formula of LNG carriers described in this paper can provide a reference for LNG carrier EEDI calculation and green shipbuilding.
LNG (liquefied natural gas): A necessary part in China's future energy infrastructure

International Nuclear Information System (INIS)

Lin, Wensheng; Gu, Anzhong; Zhang, Na

2010-01-01

This paper presents an overview of the LNG industry in China, covering LNG plants, receiving terminals, transportation, and applications. Small and medium scale LNG plants with different liquefaction processes have already been built or are being built. China's first two LNG receiving terminals have been put into operation in Guangdong and Fujian, another one is being built in Shanghai, and more are being planned. China is now able to manufacture LNG road tanks and containers. The construction of the first two LNG carriers has been completed. LNG satellite stations have been built, and LNG vehicles have been manufactured. LNG related regulations and standards are being established. The prospects of LNG in China are also discussed in this paper. Interesting topics such as small-scale liquefiers, LNG cold energy utilization, coal bed methane liquefaction, LNG plant on board (FPSO - floating production, storage, and off-loading), and LNG price are introduced and analyzed. To meet the increasing demand for natural gas, China needs to build about 10 large LNG receiving terminals, and to import LNG at the level of more than 20 bcm (billion cubic metre) per year by 2020. (author)
Hydrogen vehicle fueling station

Energy Technology Data Exchange (ETDEWEB)

Daney, D.E.; Edeskuty, F.J.; Daugherty, M.A. [Los Alamos National Lab., NM (United States)] [and others

1995-09-01

Hydrogen fueling stations are an essential element in the practical application of hydrogen as a vehicle fuel, and a number of issues such as safety, efficiency, design, and operating procedures can only be accurately addressed by a practical demonstration. Regardless of whether the vehicle is powered by an internal combustion engine or fuel cell, or whether the vehicle has a liquid or gaseous fuel tank, the fueling station is a critical technology which is the link between the local storage facility and the vehicle. Because most merchant hydrogen delivered in the US today (and in the near future) is in liquid form due to the overall economics of production and delivery, we believe a practical refueling station should be designed to receive liquid. Systems studies confirm this assumption for stations fueling up to about 300 vehicles. Our fueling station, aimed at refueling fleet vehicles, will receive hydrogen as a liquid and dispense it as either liquid, high pressure gas, or low pressure gas. Thus, it can refuel any of the three types of tanks proposed for hydrogen-powered vehicles -- liquid, gaseous, or hydride. The paper discusses the fueling station design. Results of a numerical model of liquid hydrogen vehicle tank filling, with emphasis on no vent filling, are presented to illustrate the usefulness of the model as a design tool. Results of our vehicle performance model illustrate our thesis that it is too early to judge what the preferred method of on-board vehicle fuel storage will be in practice -- thus our decision to accommodate all three methods.
Compressed Natural Gas Vehicle Maintenance Facility Modification Handbook

Energy Technology Data Exchange (ETDEWEB)

Kelly, Kay L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ramsden, Margo M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gonzales, John E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lynch, Lauren [National Renewable Energy Lab. (NREL), Golden, CO (United States); Coale, Bob [Gladstein, Neandross & Associates, Santa Monica, CA (United States); Kohout, Jarrod [Gladstein, Neandross & Associates, Santa Monica, CA (United States)

2017-09-28

gas detectors and control systems, or specialized space heating, which are not needed in facilities servicing liquid-fuel vehicles. This handbook covers maintenance facilities that service CNG-fueled vehicles. Although similar requirements are mandated for liquefied natural gas (LNG) or liquefied petroleum gas (LPG) fueled vehicles, LNG and LPG are not covered in this handbook.
Improving sustainability of maritime transport through utilization of Liquefied Natural Gas (LNG) for propulsion

International Nuclear Information System (INIS)

Burel, Fabio; Taccani, Rodolfo; Zuliani, Nicola

2013-01-01

Today, most merchant vessels use Heavy Fuel Oils (HFOs) for ship propulsion. These fuels are cost effective but they produce significant amounts of noxious emissions. In order to comply with International Maritime Organization (IMO) rules, Liquefied Natural Gas (LNG) is becoming an interesting option for merchant ships. The aim of the research presented in this paper is to analyse the economic upturn that can result from the use of LNG as fuel for merchant ships and to assess the effects of its utilization in terms of environmental impact. In the first part of the study, a statistical analysis of maritime traffic is carried out in order to identify which merchant ship types could most benefit from using LNG as fuel for ship propulsion. Traffic data of world ships related to the months of May 2008, 2009 and 2010 are analysed. Roll-on/Roll-off vessels (RoRo) and tanker ships spend most of their sailing time in Emission Control Areas (ECA) consequently appear to be the best candidates for LNG use. In particular, the use of LNG is most profitable for tanker ships in the range of 10,000–60,000 DWT (deadweight). In the second part of the study, operational costs and pollutant emission reduction, following LNG implementation, are calculated for a 33,000 DWT tanker ship. Results show that LNG leads to a reduction of 35% of operational costs and 25% of CO 2 emissions. The possibility of improving energy efficiency on board is analysed considering that combustion gases, produced by LNG, are cleaner, thus simplifying the introduction of exhaust gas heat recovery. Two options are considered: simple heat recovery and heat recovery to drive a turbine (ORC). The results show that it is possible to achieve a reduction in fuel consumption of up to 15%. - Highlights: • Ship propulsion accounts for a large amount of noxious emissions in costal/harbour areas. • Today price differential between fuel oil and natural gas is increasing. • The use of Liquefied Natural Gas as fuel
LNG systems for natural gas propelled ships

Science.gov (United States)

Chorowski, M.; Duda, P.; Polinski, J.; Skrzypacz, J.

2015-12-01

In order to reduce the atmospheric pollution generated by ships, the International Marine Organization has established Emission Controlled Areas. In these areas, nitrogen oxides, sulphur oxides and particulates emission is strongly controlled. From the beginning of 2015, the ECA covers waters 200 nautical miles from the coast of the US and Canada, the US Caribbean Sea area, the Baltic Sea, the North Sea and the English Channel. From the beginning of 2020, strong emission restrictions will also be in force outside the ECA. This requires newly constructed ships to be either equipped with exhaust gas cleaning devices or propelled with emission free fuels. In comparison to low sulphur Marine Diesel and Marine Gas Oil, LNG is a competitive fuel, both from a technical and economical point of view. LNG can be stored in vacuum insulated tanks fulfilling the difficult requirements of marine regulations. LNG must be vaporized and pressurized to the pressure which is compatible with the engine requirements (usually a few bar). The boil-off must be controlled to avoid the occasional gas release to the atmosphere. This paper presents an LNG system designed and commissioned for a Baltic Sea ferry. The specific technical features and exploitation parameters of the system will be presented. The impact of strict marine regulations on the system's thermo-mechanical construction and its performance will be discussed. The review of possible flow-schemes of LNG marine systems will be presented with respect to the system's cost, maintenance, and reliability.
Feasibility of landfill gas as a liquefied natural gas fuel source for refuse trucks.

Science.gov (United States)

Zietsman, Josias; Bari, Muhammad Ehsanul; Rand, Aaron J; Gokhale, Bhushan; Lord, Dominique; Kumar, Sunil

2008-05-01

The purpose of this paper is to develop a methodology to evaluate the feasibility of using landfill gas (LFG) as a liquefied natural gas (LNG) fuel source for heavy-duty refuse trucks operating on landfills. Using LFG as a vehicle fuel can make the landfills more self-sustaining, reduce their dependence on fossil fuels, and reduce emissions and greenhouse gases. Acrion Technologies Inc. in association with Mack Trucks Inc. developed a technology to generate LNG from LFG using the CO2 WASH process. A successful application of this process was performed at the Eco Complex in Burlington County, PA. During this application two LNG refuse trucks were operated for 600 hr each using LNG produced from gases from the landfill. The methodology developed in this paper can evaluate the feasibility of three LFG options: doing nothing, electricity generation, and producing LNG to fuel refuse trucks. The methodology involved the modeling of several components: LFG generation, energy recovery processes, fleet operations, economic feasibility, and decision-making. The economic feasibility considers factors such as capital, maintenance, operational, and fuel costs, emissions and tax benefits, and the sale of products such as surplus LNG and food-grade carbon dioxide (CO2). Texas was used as a case study. The 96 landfills in Texas were prioritized and 17 landfills were identified that showed potential for converting LFG to LNG for use as a refuse truck fuel. The methodology was applied to a pilot landfill in El Paso, TX. The analysis showed that converting LFG to LNG to fuel refuse trucks proved to be the most feasible option and that the methodology can be applied for any landfill that considers this option.
Fuel Cell Vehicle Basics | NREL

Science.gov (United States)

Fuel Cell Vehicle Basics Fuel Cell Vehicle Basics Researchers are developing fuel cells that can be silver four-door sedan being driven on a roadway and containing the words "hydrogen fuel cell electric" across the front and rear doors. This prototype hydrogen fuel cell electric vehicle was
Alcohol-fueled vehicles: An alternative fuels vehicle, emissions, and refueling infrastructure technology assessment

Energy Technology Data Exchange (ETDEWEB)

McCoy, G.A.; Kerstetter, J.; Lyons, J.K. [and others

1993-06-01

Interest in alternative motor vehicle fuels has grown tremendously over the last few years. The 1990 Clean Air Act Amendments, the National Energy Policy Act of 1992 and the California Clean Air Act are primarily responsible for this resurgence and have spurred both the motor fuels and vehicle manufacturing industries into action. For the first time, all three U.S. auto manufacturers are offering alternative fuel vehicles to the motoring public. At the same time, a small but growing alternative fuels refueling infrastructure is beginning to develop across the country. Although the recent growth in alternative motor fuels use is impressive, their market niche is still being defined. Environmental regulations, a key driver behind alternative fuel use, is forcing both car makers and the petroleum industry to clean up their products. As a result, alternative fuels no longer have a lock on the clean air market and will have to compete with conventional vehicles in meeting stringent future vehicle emission standards. The development of cleaner burning gasoline powered vehicles has signaled a shift in the marketing of alternative fuels. While they will continue to play a major part in the clean vehicle market, alternative fuels are increasingly recognized as a means to reduce oil imports. This new role is clearly defined in the National Energy Policy Act of 1992. The Act identifies alternative fuels as a key strategy for reducing imports of foreign oil and mandates their use for federal and state fleets, while reserving the right to require private and municipal fleet use as well.
Working fluid selection for an Organic Rankine Cycle utilizing high and low temperature energy of an LNG engine

International Nuclear Information System (INIS)

He, Sinian; Chang, Huawei; Zhang, Xiaoqing; Shu, Shuiming; Duan, Chen

2015-01-01

This study proposed a combined Organic Rankine Cycle (ORC) system utilizing exhaust waste as its heat source and liquid natural gas (LNG) as its heat sink to provide alternative power for an LNG-fired vehicle. This system, consisting of a regenerator and a dual heat source composite heat exchanger, was designed to efficiently recover the engine waste heat (EWH) and to guarantee vaporizing LNG steadily. Five potential applicable organic working fluids are analyzed: C4F10, CF3I, R236EA, R236FA and RC318. Each fluid was analyzed at various evaporation temperatures and condensation temperatures using a thermodynamic model, and a self-made MATLAB program based on the physical properties on REFPROP data was applied to run the simulation. Analytical results showed that fluid R236FA has the highest thermal efficiency η_t_h of 21.6%, and that of the others are also around 21%. Based on a twelve-cylinder four stroke stationary natural gas engine, the simulated calculations show that the selected five working fluids can improve the fuel economy by more than 14.7% compared to that without ORC. - Highlights: • We design an ORC utilizing LNG cold energy and engine waste heat. • Five working fluids are examined at various working conditions. • The maximum thermal efficient of our proposed cycle can reach 20.3%–21.6%. • This system can decrease the brake specific fuel consumption by more than 14.7%.
LNG [liquefied natural gas]: Fueling energy demand in the Far East

International Nuclear Information System (INIS)

Brown, R.L.

1993-01-01

An overview is presented of the supply and demand outlook for liquefied natural gas (LNG) in the far east, and the basic elements of an LNG supply project in Japan. Power generation is the primary market for LNG in the far east, due to a preference for energy supply diversity, large undeveloped gas resources, drastic improvements in power generation technology, and environmental advantages of natural gas. India and mainland China represent huge potential markets, and projects are under discussion to bring gas by pipeline from Iran or Qatar to both Pakistan or India. The economics of LNG plant development in Japan, including large ($4 billion for field and plant development) capital costs, long-term contracts, government involvement, and gas prices are discussed. Falling yen/dollar exchange rates have substantially bettered the Japanese economy in terms of gas prices. 11 figs., 2 tabs
LNG (liquefied natural gas): A necessary part in China's future energy infrastructure

Energy Technology Data Exchange (ETDEWEB)

Lin, Wensheng; Gu, Anzhong [Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University, Shanghai 200240 (China); Zhang, Na [Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100080 (China)

2010-11-15

This paper presents an overview of the LNG industry in China, covering LNG plants, receiving terminals, transportation, and applications. Small and medium scale LNG plants with different liquefaction processes have already been built or are being built. China's first two LNG receiving terminals have been put into operation in Guangdong and Fujian, another one is being built in Shanghai, and more are being planned. China is now able to manufacture LNG road tanks and containers. The construction of the first two LNG carriers has been completed. LNG satellite stations have been built, and LNG vehicles have been manufactured. LNG related regulations and standards are being established. The prospects of LNG in China are also discussed in this paper. Interesting topics such as small-scale liquefiers, LNG cold energy utilization, coal bed methane liquefaction, LNG plant on board (FPSO - floating production, storage, and off-loading), and LNG price are introduced and analyzed. To meet the increasing demand for natural gas, China needs to build about 10 large LNG receiving terminals, and to import LNG at the level of more than 20 bcm (billion cubic metre) per year by 2020. (author)
LNG ventures raise economic, technical, partnership issues

International Nuclear Information System (INIS)

Acord, H.K.

1995-01-01

The author feels that natural gas will remain a competitive energy alternative and the preferred fuel for many residential and industrial customers around the globe. The article attempts to explain where liquefied natural gas will fit into the global picture. The paper discusses the growth in the Asia-Pacific region; the complex interactions in a LNG project involving buyers, sellers, governments, financial institutions, and shipping companies; the cost of development of such projects; and the elements of a LNG venture
LNG

International Nuclear Information System (INIS)

Chabrelie, M.F.; Idir, N.; Hosanski, J.M.; Jonkman, H.; Pelloux-Prayer, D.; Wells, D.

2007-01-01

The LNG industry has entered a new step of its development, faster and more complex. The time parameter, the huge investments and the uncertainties relative to the demand growth are some of the factors that control its evolution. How the emergence of 'international price' signals will influence this activity? What supply-demand status can be foreseen from now to 2015? What role LNG would be able to play in terms of modulation management? What are the impacts of environmental constraints on LNG infrastructures? These are the different points discussed during this workshop by the five participants, specialists of the LNG questions. (J.S.)
Advances in fuel cell vehicle design

Science.gov (United States)

Bauman, Jennifer

Factors such as global warming, dwindling fossil fuel reserves, and energy security concerns combine to indicate that a replacement for the internal combustion engine (ICE) vehicle is needed. Fuel cell vehicles have the potential to address the problems surrounding the ICE vehicle without imposing any significant restrictions on vehicle performance, driving range, or refuelling time. Though there are currently some obstacles to overcome before attaining the widespread commercialization of fuel cell vehicles, such as improvements in fuel cell and battery durability, development of a hydrogen infrastructure, and reduction of high costs, the fundamental concept of the fuel cell vehicle is strong: it is efficient, emits zero harmful emissions, and the hydrogen fuel can be produced from various renewable sources. Therefore, research on fuel cell vehicle design is imperative in order to improve vehicle performance and durability, increase efficiency, and reduce costs. This thesis makes a number of key contributions to the advancement of fuel cell vehicle design within two main research areas: powertrain design and DC/DC converters. With regards to powertrain design, this research first analyzes various powertrain topologies and energy storage system types. Then, a novel fuel cell-battery-ultracapacitor topology is presented which shows reduced mass and cost, and increased efficiency, over other promising topologies found in the literature. A detailed vehicle simulator is created in MATLAB/Simulink in order to simulate and compare the novel topology with other fuel cell vehicle powertrain options. A parametric study is performed to optimize each powertrain and general conclusions for optimal topologies, as well as component types and sizes, for fuel cell vehicles are presented. Next, an analytical method to optimize the novel battery-ultracapacitor energy storage system based on maximizing efficiency, and minimizing cost and mass, is developed. This method can be applied
Fuel Cell Electric Vehicle Evaluations | Hydrogen and Fuel Cells | NREL

Science.gov (United States)

Electric Vehicle Evaluations Fuel Cell Electric Vehicle Evaluations NREL's technology validation team analyzes hydrogen fuel cell electric vehicles (FCEVs) operating in a real-world setting to include commercial FCEVs for the first time. Current fuel cell electric vehicle evaluations build on the
Sensor system for fuel transport vehicle

Science.gov (United States)

Earl, Dennis Duncan; McIntyre, Timothy J.; West, David L.

2016-03-22

An exemplary sensor system for a fuel transport vehicle can comprise a fuel marker sensor positioned between a fuel storage chamber of the vehicle and an access valve for the fuel storage chamber of the vehicle. The fuel marker sensor can be configured to measure one or more characteristics of one or more fuel markers present in the fuel adjacent the sensor, such as when the marked fuel is unloaded at a retail station. The one or more characteristics can comprise concentration and/or identity of the one or more fuel markers in the fuel. Based on the measured characteristics of the one or more fuel markers, the sensor system can identify the fuel and/or can determine whether the fuel has been adulterated after the marked fuel was last measured, such as when the marked fuel was loaded into the vehicle.

China's energy and environmental quandary: is LNG the answer?

International Nuclear Information System (INIS)

Williams, M.F.; King, B.S.

1996-01-01

Economic growth in China has inevitably lead to an increased energy demand to fuel industrial production, infrastructural and domestic needs. To date much of China's generating capacity has been coal-based, without flue gas desulphurisation. The serious environmental effects of such a policy are being reexamined in the light of rapid growth in demand. This paper argues that power generation by combined cycle gas turbines and fuelled by natural gas, supplied as LNG could provide a solution. Imported LNG to fuel such turbines could, it is argued, be used to generate electricity at prices competitive with imported coal and other sources of domestic gas. (UK)
Raley's LNG Truck Site Final Data Report

Energy Technology Data Exchange (ETDEWEB)

Battelle

1999-07-01

Raley's is a 120-store grocery chain with headquarters in Sacramento, California, that has been operating eight heavy-duty LNG trucks (Kenworth T800 trucks with Cummins L10-300G engines) and two LNG yard tractors (Ottawa trucks with Cummins B5.9G engines) since April 1997. This report describes the results of data collection and evaluation of the eight heavy-duty LNG trucks compared to similar heavy-duty diesel trucks operating at Raley's. The data collection and evaluation are a part of the U.S. Department of Energy (DOE)/National Renewable Energy Laboratory (NREL) Alternative Fuel Truck Evaluation Project.
Modeling the release, spreading, and burning of LNG, LPG, and gasoline on water

International Nuclear Information System (INIS)

Johnson, David W.; Cornwell, John B.

2007-01-01

Current interest in the shipment of liquefied natural gas (LNG) has renewed the debate about the safety of shipping large volumes of flammable fuels. The size of a spreading pool following a release of LNG from an LNG tank ship has been the subject of numerous papers and studies dating back to the mid-1970s. Several papers have presented idealized views of how the LNG would be released and spread across a quiescent water surface. There is a considerable amount of publicly available material describing these idealized releases, but little discussion of how other flammable fuels would behave if released from similar sized ships. The purpose of this paper is to determine whether the models currently available from the United States Federal Energy Regulatory Commission (FERC) can be used to simulate the release, spreading, vaporization, and pool fire impacts for materials other than LNG, and if so, identify which material-specific parameters are required. The review of the basic equations and principles in FERC's LNG release, spreading, and burning models did not reveal a critical fault that would prevent their use in evaluating the consequences of other flammable fluid releases. With the correct physical data, the models can be used with the same level of confidence for materials such as LPG and gasoline as they are for LNG
Advanced Technology and Alternative Fuel Vehicles

International Nuclear Information System (INIS)

Tuttle, J.

2001-01-01

This fact sheet provides a basic overview of today's alternative fuel choices--including biofuels, biodiesel, electricity, and hydrogen--alternative fuel vehicles, and advanced vehicle technology, such as hybrid electric vehicles, fuel cells and advanced drive trains
World LNG outlook

International Nuclear Information System (INIS)

Maisonnier, G.

1999-01-01

CEDIGAZ proposes this new survey about LNG in view of the main changes which have occurred on this market during the past few years. Several projects under construction or planned three years ago are now commissioned (Qatargas) or on the verge of starting to export this year (Trinidad LNG, RasGas, Nigeria LNG) or next years (Oman LNG). The Asian crisis, which had major impacts on both short-term demand in Asia and LNG prices, has brought about new uncertainties to the long-term prospects. At the same time, it now seems more and more certain that firstly India and then China will import LNG in the next decade. It remains to be seen at what level and when this will occur. LNG growth in Europe has now become a reality, and new potential markets, for example in South America (Brazil), are also being considered as real opportunities in the near future. Considering these 'new' trends, an updated study about LNG appeared necessary. This survey 'World LNG Outlook - 99 Edition' is organised as the previous one: a historical record since 1964 (Chapter 1) followed by a description of the infrastructures existing in 1998 (Chapter 2). The analysis continues with world trade prospects by the year 2010 (Chapters 3 to 5). Chapter 6 describes the future LNG chain and the last Chapter (7) focuses on economic matters (LNG price trends, cost reductions). The study 'World LNG Outlook - 99 Edition' offers hence a comprehensive panorama of this sector from a short and long-term point of view. (author)
Kitimat LNG terminal

International Nuclear Information System (INIS)

Schmaltz, I.; Boulton, R.

2007-01-01

Kitimat Liquefied Natural Gas (LNG) terminal is a terminal development company owned by Galveston LNG, a privately owned Canadian energy development company. This presentation provided information on Kitimat LNG with particular reference to its terminal located in Bish Cove on the Douglas Channel in British Columbia. This LNG terminal is reported to be the only fully permitted regasification terminal on the west coast of Canada and the United States. The presentation addressed market fundamentals including several graphs, such as world natural gas proved reserves in 2006; LNG supplements to Canadian gas supplies; global LNG demand for 2005-2020; average annual United States LNG imports; and global LNG liquefaction projects. Other market fundamentals were described, including that Kitimat is the only other approved terminal aside from the Costa Azul terminal in Mexico; Kitimat is the only west coast LNG import terminal that connects to midwest and eastern North American markets through existing gas pipelines; LNG producers are looking for destination diversification; and markets and marketers are looking for supply diversification. The authors noted that by 2010, western Canadian gas demand will exceed Californian demand. Other topics that were discussed in the presentation included Canadian natural gas field receipts; unadjusted bitumen production outlook; oil sands gas demand; forward basis fundamentals; and the commercial drivers of the Kitimat LNG terminal. The presentation also discussed the pacific trail pipelines, a partnership between Galveston LNG and Pacific Northern Gas to develop the natural gas transmission line from Kitimat to Summit. The presentation concluded with a discussion of the benefits of Kitimat LNG terminal such as providing access to the largest natural gas markets in the world via major gas transmission lines with spare capacity. figs
Investigation of propulsion system for large LNG ships

International Nuclear Information System (INIS)

Sinha, R P; Wan Nik, Wan Mohd Norsani

2012-01-01

Requirements to move away from coal for power generation has made LNG as the most sought after fuel source, raising steep demands on its supply and production. Added to this scenario is the gradual depletion of the offshore oil and gas fields which is pushing future explorations and production activities far away into the hostile environment of deep sea. Production of gas in such environment has great technical and commercial impacts on gas business. For instance, laying gas pipes from deep sea to distant receiving terminals will be technically and economically challenging. Alternative to laying gas pipes will require installing re-liquefaction unit on board FPSOs to convert gas into liquid for transportation by sea. But, then because of increased distance between gas source and receiving terminals the current medium size LNG ships will no longer remain economical to operate. Recognizing this business scenario shipowners are making huge investments in the acquisition of large LNG ships. As power need of large LNG ships is very different from the current small ones, a variety of propulsion derivatives such as UST, DFDE, 2-Stroke DRL and Combined cycle GT have been proposed by leading engine manufacturers. Since, propulsion system constitutes major element of the ship's capital and life cycle cost, which of these options is most suited for large LNG ships is currently a major concern of the shipping industry and must be thoroughly assessed. In this paper the authors investigate relative merits of these propulsion options against the benchmark performance criteria of BOG disposal, fuel consumption, gas emissions, plant availability and overall life cycle cost.
Investigation of propulsion system for large LNG ships

Science.gov (United States)

Sinha, R. P.; Nik, Wan Mohd Norsani Wan

2012-09-01

Requirements to move away from coal for power generation has made LNG as the most sought after fuel source, raising steep demands on its supply and production. Added to this scenario is the gradual depletion of the offshore oil and gas fields which is pushing future explorations and production activities far away into the hostile environment of deep sea. Production of gas in such environment has great technical and commercial impacts on gas business. For instance, laying gas pipes from deep sea to distant receiving terminals will be technically and economically challenging. Alternative to laying gas pipes will require installing re-liquefaction unit on board FPSOs to convert gas into liquid for transportation by sea. But, then because of increased distance between gas source and receiving terminals the current medium size LNG ships will no longer remain economical to operate. Recognizing this business scenario shipowners are making huge investments in the acquisition of large LNG ships. As power need of large LNG ships is very different from the current small ones, a variety of propulsion derivatives such as UST, DFDE, 2-Stroke DRL and Combined cycle GT have been proposed by leading engine manufacturers. Since, propulsion system constitutes major element of the ship's capital and life cycle cost, which of these options is most suited for large LNG ships is currently a major concern of the shipping industry and must be thoroughly assessed. In this paper the authors investigate relative merits of these propulsion options against the benchmark performance criteria of BOG disposal, fuel consumption, gas emissions, plant availability and overall life cycle cost.
The heavy-duty vehicle future in the United States: A parametric analysis of technology and policy tradeoffs

International Nuclear Information System (INIS)

Askin, Amanda C.; Barter, Garrett E.; West, Todd H.; Manley, Dawn K.

2015-01-01

We present a parametric analysis of factors that can influence advanced fuel and technology deployments in U.S. Class 7–8 trucks through 2050. The analysis focuses on the competition between traditional diesel trucks, natural gas vehicles (NGVs), and ultra-efficient powertrains. Underlying the study is a vehicle choice and stock model of the U.S. heavy-duty vehicle market. The model is segmented by vehicle class, body type, powertrain, fleet size, and operational type. We find that conventional diesel trucks will dominate the market through 2050, but NGVs could have significant market penetration depending on key technological and economic uncertainties. Compressed natural gas trucks conducting urban trips in fleets that can support private infrastructure are economically viable now and will continue to gain market share. Ultra-efficient diesel trucks, exemplified by the U.S. Department of Energy's SuperTruck program, are the preferred alternative in the long haul segment, but could compete with liquefied natural gas (LNG) trucks if the fuel price differential between LNG and diesel increases. However, the greatest impact in reducing petroleum consumption and pollutant emissions is had by investing in efficiency technologies that benefit all powertrains, especially the conventional diesels that comprise the majority of the stock, instead of incentivizing specific alternatives. -- Highlights: •We present a parametric analysis of factors U.S. Class 7–8 trucks through 2050. •Conventional diesels will be more than 70% of U.S. heavy-duty vehicles through 2050. •CNG trucks are well suited to large, urban fleets with private refueling. •Ultra-efficient long haul diesel trucks are preferred over LNG at current fuel prices
Panorama 2016 - LNG in transportation: what is its potential for the sector?

International Nuclear Information System (INIS)

Jordan, Louis

2015-12-01

With low emissions and competitive pricing, liquefied natural gas (LNG) appears to have significant advantages to emerge as an alternative or supplement to traditional fossil fuels. Although LNG has significant potential for growth over the long term, it will have to eliminate some uncertainties, especially those related to supply infrastructure. (author)
Clean sailing. LNG terminals. Maritime infrastructure for liquefied natural gas; Sauber auf See. LNG-Terminals. Maritime Infrastruktur fuer fluessiges Erdgas

Energy Technology Data Exchange (ETDEWEB)

Anon.

2013-09-01

Ports act as essential hubs in the global economy. But the rise in maritime traffic is taking a toll on the quality of air in ports and out at sea. From 2015 onwards, threshold governing harmful emissions are being tightened in a bid to clear the air. All of which is driving interest in more environmentally sound fuels. Liquefied natural gas (LNG) is the perfect fit, more than complying with the upcoming regulations. To enable its widespread adoption, Linde is working full steam ahead to create a network of LNG terminals in Europe. (orig.)
Development of a 1200 KW/CYL low pressure dual fuel engine for LNG carriers

Energy Technology Data Exchange (ETDEWEB)

Grosshans, G. [S.E.M.T.-Pielstick, Thermodynamical Project Dept. (France)

1998-12-31

This paper describes the design and feasibility tests of a 570 mm bore 4 stroke low pressure (L.P.) dual fuel engine rated at 20.9 bar BMEP meant for the propulsion of LNG carriers. The basic design features which are to be in accordance with classification societies safety rules are described: individual electro hydraulic valves located in the air manifold ducts, pilot injection, monitoring system etc. The engine capability to burn variable liquid/gas fuel proportions have been investigated with diesel oil and heavy fuel and possible running zones are defined. This ensures the possibility of the engine to cope with the different boil off gas quantity emanating from the ship`s tank during her loaded - and ballast - journeys. With the very lean setting of this engine, no adverse influence of the high ash lube-oil additives were found during the tests. Further tests are necessary to confirm that possible more significant fouling of the combustion chamber is still acceptable. (au)
Fuel Cell Electric Vehicle Composite Data Products | Hydrogen and Fuel

Science.gov (United States)

Cells | NREL Vehicle Composite Data Products Fuel Cell Electric Vehicle Composite Data Products The following composite data products (CDPs) focus on current fuel cell electric vehicle evaluations Cell Operation Hour Groups CDP FCEV 39, 2/19/16 Comparison of Fuel Cell Stack Operation Hours and Miles
A comparison of hydrogen, methanol and gasoline as fuels for fuel cell vehicles: implications for vehicle design and infrastructure development

Science.gov (United States)

Ogden, Joan M.; Steinbugler, Margaret M.; Kreutz, Thomas G.

All fuel cells currently being developed for near term use in electric vehicles require hydrogen as a fuel. Hydrogen can be stored directly or produced onboard the vehicle by reforming methanol, or hydrocarbon fuels derived from crude oil (e.g., gasoline, diesel, or middle distillates). The vehicle design is simpler with direct hydrogen storage, but requires developing a more complex refueling infrastructure. In this paper, we present modeling results comparing three leading options for fuel storage onboard fuel cell vehicles: (a) compressed gas hydrogen storage, (b) onboard steam reforming of methanol, (c) onboard partial oxidation (POX) of hydrocarbon fuels derived from crude oil. We have developed a fuel cell vehicle model, including detailed models of onboard fuel processors. This allows us to compare the vehicle performance, fuel economy, weight, and cost for various vehicle parameters, fuel storage choices and driving cycles. The infrastructure requirements are also compared for gaseous hydrogen, methanol and gasoline, including the added costs of fuel production, storage, distribution and refueling stations. The delivered fuel cost, total lifecycle cost of transportation, and capital cost of infrastructure development are estimated for each alternative. Considering both vehicle and infrastructure issues, possible fuel strategies leading to the commercialization of fuel cell vehicles are discussed.
Predicting vehicle fuel consumption patterns using floating vehicle data.

Science.gov (United States)

Du, Yiman; Wu, Jianping; Yang, Senyan; Zhou, Liutong

2017-09-01

The status of energy consumption and air pollution in China is serious. It is important to analyze and predict the different fuel consumption of various types of vehicles under different influence factors. In order to fully describe the relationship between fuel consumption and the impact factors, massive amounts of floating vehicle data were used. The fuel consumption pattern and congestion pattern based on large samples of historical floating vehicle data were explored, drivers' information and vehicles' parameters from different group classification were probed, and the average velocity and average fuel consumption in the temporal dimension and spatial dimension were analyzed respectively. The fuel consumption forecasting model was established by using a Back Propagation Neural Network. Part of the sample set was used to train the forecasting model and the remaining part of the sample set was used as input to the forecasting model. Copyright © 2017. Published by Elsevier B.V.
Alternative Fuels Data Center: How Do Fuel Cell Electric Vehicles Work

Science.gov (United States)

vehicles. Hydrogen car image Key Components of a Hydrogen Fuel Cell Electric Car Battery (auxiliary): In an Using Hydrogen? Fuel Cell Electric Vehicles Work Using Hydrogen? to someone by E-mail Share Alternative Fuels Data Center: How Do Fuel Cell Electric Vehicles Work Using Hydrogen? on Facebook Tweet about
Hydrogen as a fuel for fuel cell vehicles: A technical and economic comparison

Energy Technology Data Exchange (ETDEWEB)

Ogden, J.; Steinbugler, M.; Kreutz, T. [Princeton Univ., NJ (United States). Center for Energy and Environmental Studies

1997-12-31

All fuel cells currently being developed for near term use in vehicles require hydrogen as a fuel. Hydrogen can be stored directly or produced onboard the vehicle by reforming methanol, ethanol or hydrocarbon fuels derived from crude oil (e.g., Diesel, gasoline or middle distillates). The vehicle design is simpler with direct hydrogen storage, but requires developing a more complex refueling infrastructure. In this paper, the authors compare three leading options for fuel storage onboard fuel cell vehicles: compressed gas hydrogen storage; onboard steam reforming of methanol; onboard partial oxidation (POX) of hydrocarbon fuels derived from crude oil. Equilibrium, kinetic and heat integrated system (ASPEN) models have been developed to estimate the performance of onboard steam reforming and POX fuel processors. These results have been incorporated into a fuel cell vehicle model, allowing us to compare the vehicle performance, fuel economy, weight, and cost for various fuel storage choices and driving cycles. A range of technical and economic parameters were considered. The infrastructure requirements are also compared for gaseous hydrogen, methanol and hydrocarbon fuels from crude oil, including the added costs of fuel production, storage, distribution and refueling stations. Considering both vehicle and infrastructure issues, the authors compare hydrogen to other fuel cell vehicle fuels. Technical and economic goals for fuel cell vehicle and hydrogen technologies are discussed. Potential roles for hydrogen in the commercialization of fuel cell vehicles are sketched.
LNG; GNL

Energy Technology Data Exchange (ETDEWEB)

Chabrelie, M.F. [Cedigaz, 1 - 4 Avenue de Bois-Preau, 92852 Rueil Malmaison (France); Idir, N. [Commission de regulation de l' energie - CRE, 2 rue du Quatre-Septembre, 75084 Paris Cedex 02 (France); Hosanski, J.M. [Total, Dir. Gaz et Electricite, 2 place de la Coupole, La Defense 6, 92400 Courbevoie (France); Jonkman, H. [CEO, 4Gas, Max Euwelaan 21, 3062 MA Rotterdam (Netherlands); Pelloux-Prayer, D. [Gaz de France, 75 - Paris (France); Wells, D. [Shell Global LNG (United States)

2007-07-01

The LNG industry has entered a new step of its development, faster and more complex. The time parameter, the huge investments and the uncertainties relative to the demand growth are some of the factors that control its evolution. How the emergence of 'international price' signals will influence this activity? What supply-demand status can be foreseen from now to 2015? What role LNG would be able to play in terms of modulation management? What are the impacts of environmental constraints on LNG infrastructures? These are the different points discussed during this workshop by the five participants, specialists of the LNG questions. (J.S.)
Application tests of a new-type LNG rapid gasification unit

Directory of Open Access Journals (Sweden)

Ping Yan

2017-01-01

Full Text Available Liquefied natural gas (LNG is stored under low temperature and high pressure. It has to be gasified before it is used. Therefore, LNG gasification unit is essential and it is vital to the high-efficiency utilization of LNG. In this paper, a new-type LNG rapid gasification unit was developed. Adopted in this unit are some innovative technologies authorized with the national patent of invention, such as the umbrella-shape gas flow circle unit, the flue gas circulation system and the water feeding system, which help to guarantee its operation safety and increase its operation efficiency. After it was justified in lab test, the unit for industrial application was designed and manufactured and then tested to verify its design rationality. The results show that the new-type LNG rapid gasification unit meets the design requirements in the aspect of efficiency, exhaust gas loss, radiation loss and fuel gas consumption rate; at a load of 1800–2200 m3/h, its efficiency is over 95%; at a load of 1976.0 m3/h which is close to the design value of 2000 m3/h, its efficiency is 96.34% or even up to 2800 m3/h. This new-type LNG rapid gasification unit is adaptable to a large range of loads and can adapt to the rapid increase of external load. Its fuel gas consumption rate is only 1.5%, which is in the range of energy conservation. It presents the advantages of high heating efficiency, rapid startup, high gasification rate, compact structure, small land occupation and invulnerability to the environment, therefore, it is applicable to the middle and small independent regions which cannot be connected to the natural gas supply pipeline networks due to various reasons.
40 CFR 79.33 - Motor vehicle diesel fuel.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Motor vehicle diesel fuel. 79.33... diesel fuel. (a) The following fuels commonly or commercially known or sold as motor vehicle diesel fuel are hereby individually designated: (1) Motor vehicle diesel fuel, grade 1-D; (2) Motor vehicle diesel...

Maritime prerequisites for development of infrastructure for liquefied natural gas (LNG / LBG); Maritima foerutsaettningar foer utbyggnad av infrastruktur foer flytande gas (LNG/LBG)

Energy Technology Data Exchange (ETDEWEB)

Gahnstroem, Johan; Molitor, Edvard; Raggl, Karl-Johan; Sandkvist, Jim [SSPA Sweden AB, Goeteborg (Sweden)

2011-06-15

This study has provided an initial picture of where the most interesting ports and areas available for future expansion of a maritime infrastructure for LNG. On the basis of supplying vessels with LNG as fuel, from a long term perspective, we recommend locating LNG terminals in or near major ports and around the big ship routes. Given the current age distribution of ships operating waters of the Baltic Sea, almost 20% of the vessels are 30-40 years old and likely to be replaced by 2015 - 2020. Thus, there is a potential for newly built ships will be equipped with LNG operation. Selected criteria s; Size of the LNG terminal and hence the need for the size of the fairway and the area of land. Proximity to traffic routes with much ship traffic. Proximity to the major port. Proximity to consumers on the land side. On the basis of selected criteria and analyzed for possible location of the terminal it can be noted that a number of Swedish ports are found suitable. For example, ports of Sundsvall, Gothenburg and Helsingborg has been identified as suitable, but with different starting point and different types and sizes of terminals possible.
Reduction of LNG FOB cost

International Nuclear Information System (INIS)

Aoki, Ichizo; Kikkawa, Yoshitsugi

1997-01-01

To achieve a competitive LNG price for the consumers against other energy sources, reduction of LNG FOB (Free on Board) cost i.e. LNG cost at LNG ship flange, will be the key item. It is necessary to perform a many optimization studies (or value engineering) for each stage of the LNG project. These stages are: Feasibility study; Conceptual design - FEED (Front End Engineering and Design); EPC (Engineering, Procurement and Construction); Operation and maintenance. Since the LNG plant forms one part of the LNG chain, starting from gas production to LNG receiving, and requires several billion US dollar of investment, the consequences of a plant shut down on the LNG chain are clear, it is, therefore, important to get high availability which will also contribute the reduction of LNG FOB cost. (au) 25 refs
Market penetration scenarios for fuel cell vehicles

Energy Technology Data Exchange (ETDEWEB)

Thomas, C.E.; James, B.D.; Lomax, F.D. Jr. [Directed Technologies, Inc., Arlington, VA (United States)

1997-12-31

Fuel cell vehicles may create the first mass market for hydrogen as an energy carrier. Directed Technologies, Inc., working with the US Department of Energy hydrogen systems analysis team, has developed a time-dependent computer market penetration model. This model estimates the number of fuel cell vehicles that would be purchased over time as a function of their cost and the cost of hydrogen relative to the costs of competing vehicles and fuels. The model then calculates the return on investment for fuel cell vehicle manufacturers and hydrogen fuel suppliers. The model also projects the benefit/cost ratio for government--the ratio of societal benefits such as reduced oil consumption, reduced urban air pollution and reduced greenhouse gas emissions to the government cost for assisting the development of hydrogen energy and fuel cell vehicle technologies. The purpose of this model is to assist industry and government in choosing the best investment strategies to achieve significant return on investment and to maximize benefit/cost ratios. The model can illustrate trends and highlight the sensitivity of market penetration to various parameters such as fuel cell efficiency, cost, weight, and hydrogen cost. It can also illustrate the potential benefits of successful R and D and early demonstration projects. Results will be shown comparing the market penetration and return on investment estimates for direct hydrogen fuel cell vehicles compared to fuel cell vehicles with onboard fuel processors including methanol steam reformers and gasoline partial oxidation systems. Other alternative fueled vehicles including natural gas hybrids, direct injection diesels and hydrogen-powered internal combustion hybrid vehicles will also be analyzed.
Challenges of LNG (Liquefied Natural Gas Carriers in 21" Century

Directory of Open Access Journals (Sweden)

Marina Zanne

2009-01-01

Full Text Available Natural gas is relatively cheap, environmentally friendlyand energetically efficient fossil fuel that is gaining in attractivenessdaily as it can be used in many sectors. As not all consumerscan be reached by pipelines the technique of transp01tingnatural gas in the liquefied form has been developed at the beginningof 20th century but it was only in 1959 that the firstoverseas transport of liquefied natural gas ( LN G occurred. Inthe fifty years of operation LNG shipping has shown immaculatesafety records. LNG tankers can be described only in superlatives;they are without any doubt the most sophisticated and·expensive ships that sail around the globe, they demand specialattention when navigating to or out of harbours and need to bemanned with the most educated and experienced crew. LNGmarket is expanding and changing; demand is surpassing theproductivity, new importing and exporting countries appear,LNG fleet is growing in capacity and number at high pace, exploitationcontracts for the ships are being modified giving theopportunity for new companies to enter( . .. . The paper givesan overview on liquefied natural gas market and the historic developmentof LNG shipping. It focuses on the recent boom inLNG shipping and emphasises questions concerning the safety,crewing and exploitation of the LNG tankers in the future.
LNG transport through pipelines

Energy Technology Data Exchange (ETDEWEB)

Pfund, P; Philipps, A

1975-01-01

LNG pipelines could help solve some peakshaving problems if operated in conjunction with other facilities that could use the LNG cold recovered during regasification. In some areas at present, LNG is delivered by tanker and regasified near the terminal for transmission through conventional gas pipelines. In other places, utilities liquefy natural gas for easy storage for later peakshaving use. The only chance to avoid the second expensive liquefaction step would be to convey imported LNG through a suitable designed LNG pipeline. The technical problems involved in LNG pipeline construction have basically been solved in recent years, but those pipelines actually constructed have been only short ones. To be economically justified, long-distance LNG lines require additional credit, which could be obtained by selling the LNG cold recovered during regasification to industrial users located in or near the points of gas consumption. Technical details presented cover the pipe material, stress relief, steel composition, pressure enthalpy, bellows-type expansion joints, and mechanical and thermal insulation.
Dossier LNG. Liquid market move

International Nuclear Information System (INIS)

Matla, P.

2012-01-01

The worldwide market for liquid natural gas is booming like never before and the end is not in sight yet. Shell is market leader among international energy companies. But where does LNG come from? And how will the fuel be used in the coming years? What role does Shell want to play in this market? These questions are addressed in a series of three articles. [nl
Emissions from ethanol- and LPG-fueled vehicles

International Nuclear Information System (INIS)

Pitstick, M.E.

1995-01-01

This paper addresses the environmental concerns of using neat ethanol and liquefied petroleum gas (LPG) as transportation fuels in the United States. Low-level blends of ethanol (10%) with gasoline have been used as fuels in the United States for more than a decade, but neat ethanol (85% or more) has only been used extensively in Brazil. LPG, which consists mostly of propane, is already used extensively as a vehicle fuel in the United States, but its use has been limited primarily to converted fleet vehicles. Increasing U.S. interest in alternative fuels has raised the possibility of introducing neat-ethanol vehicles into the market and expanding the number of LPG vehicles. Use of such vehicles, and increased production and consumption of fuel ethanol and LPG, will undoubtedly have environmental impacts. If the impacts are determined to be severe, they could act as barriers to the introduction of neat-ethanol and LPG vehicles. Environmental concerns include exhaust and evaporative emissions and their impact on ozone formation and global warming, toxic emissions from fuel combustion and evaporation, and agricultural impacts from production of ethanol. The paper is not intended to be judgmental regarding the overall attractiveness of ethanol or LPG as compared with other transportation fuels. The environmental concerns are reviewed and summarized, but only conclusion reached is that there is no single concern that is likely to prevent the introduction of neat-ethanol-fueled vehicles or the increase in LPG-fueled vehicles
The LNG Industry - 2013

International Nuclear Information System (INIS)

Dispenza, Domenico

2014-04-01

In 2013 the LNG markets remained extremely tight due to the demand pull from nuclear closures in Japan and South Korea and the difficulties to ramp-up production of new facilities in Angola and Algeria, bringing LNG price levels in the Far East to record highs in the first quarter. In addition to Cheniere's Sabine Pass, three new liquefaction projects received full approvals in the U.S.A. last year, confirming the country's path to become the world's third largest LNG exporter by the end of the decade. Cameron joined their ranks in early 2014 so that at the time of this writing, a total 62.5 Mt/y of capacity have been approved to export to non-FTA countries by the Department of Energy, already impacting the LNG industry, if not in physical volume then in contracting strategy. 2013 could be considered a transition year. LNG traded volumes as a whole remained at the same level as in 2012, but new trade patterns seem to emerge. The past year may have seen a slowdown in the number of FIDs, counting only one greenfield (Yamal LNG) and two expansion projects, but not in capacity increase with a respectable 29 Mt/y committed in total. Demand remained strong in Asia, mainly in China and South Korea. In Japan, imports continued to increase, although more moderately in a response to high prices and the yen devaluation, shifting the energy mix towards other sources of energy. Demand also increased in South America, strongly related to weather factors. Europe remained the swing provider to the world's LNG market. In a context of depressed local demand and with the utilization rate of the re-gasification terminals in their region at a historical low, European players continued with innovative transactions in search for business (such as re-loadings, two-port loadings, ship-to-ship transfers) while developing new markets for LNG as a transportation fuel. Three new countries joined the ranks of LNG importers in 2013: Israel, Malaysia, and Singapore. Total
Fuel options for the fuel cell vehicle: hydrogen, methanol or gasoline?

International Nuclear Information System (INIS)

Thomas, C.E.; James, B.D.; Lomax, F.D. Jr.; Kuhn, I.F. Jr.

2000-01-01

Fuel cell vehicles can be powered directly by hydrogen or, with an onboard chemical processor, other liquid fuels such as gasoline or methanol. Most analysts agree that hydrogen is the preferred fuel in terms of reducing vehicle complexity, but one common perception is that the cost of a hydrogen infrastructure would be excessive. According to this conventional wisdom, the automobile industry must therefore develop complex onboard fuel processors to convert methanol, ethanol or gasoline to hydrogen. We show here, however, that the total fuel infrastructure cost to society including onboard fuel processors may be less for hydrogen than for either gasoline or methanol, the primary initial candidates currently under consideration for fuel cell vehicles. We also present the local air pollution and greenhouse gas advantages of hydrogen fuel cell vehicles compared to those powered by gasoline or methanol. (Author)
16 CFR 309.10 - Alternative vehicle fuel rating.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Alternative vehicle fuel rating. 309.10... LABELING REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fuels Duties of Importers, Producers, and Refiners of Non-Liquid Alternative Vehicle Fuels (other Than...
Fuel economy of hybrid fuel-cell vehicles

Science.gov (United States)

Ahluwalia, Rajesh K.; Wang, X.; Rousseau, A.

The potential improvement in fuel economy of a mid-size fuel-cell vehicle by combining it with an energy storage system has been assessed. An energy management strategy is developed and used to operate the direct hydrogen, pressurized fuel-cell system in a load-following mode and the energy storage system in a charge-sustaining mode. The strategy places highest priority on maintaining the energy storage system in a state where it can supply unanticipated boost power when the fuel-cell system alone cannot meet the power demand. It is found that downsizing a fuel-cell system decreases its efficiency on a drive cycle which is compensated by partial regenerative capture of braking energy. On a highway cycle with limited braking energy the increase in fuel economy with hybridization is small but on the stop-and-go urban cycle the fuel economy can improve by 27%. On the combined highway and urban drive cycles the fuel economy of the fuel-cell vehicle is estimated to increase by up to 15% by hybridizing it with an energy storage system.
Fuel economy and life-cycle cost analysis of a fuel cell hybrid vehicle

Science.gov (United States)

Jeong, Kwi Seong; Oh, Byeong Soo

The most promising vehicle engine that can overcome the problem of present internal combustion is the hydrogen fuel cell. Fuel cells are devices that change chemical energy directly into electrical energy without combustion. Pure fuel cell vehicles and fuel cell hybrid vehicles (i.e. a combination of fuel cell and battery) as energy sources are studied. Considerations of efficiency, fuel economy, and the characteristics of power output in hybridization of fuel cell vehicle are necessary. In the case of Federal Urban Driving Schedule (FUDS) cycle simulation, hybridization is more efficient than a pure fuel cell vehicle. The reason is that it is possible to capture regenerative braking energy and to operate the fuel cell system within a more efficient range by using battery. Life-cycle cost is largely affected by the fuel cell size, fuel cell cost, and hydrogen cost. When the cost of fuel cell is high, hybridization is profitable, but when the cost of fuel cell is less than 400 US$/kW, a pure fuel cell vehicle is more profitable.
Alternative Fuels Data Center: Natural Gas Vehicles

Science.gov (United States)

Natural Gas Printable Version Share this resource Send a link to Alternative Fuels Data Center : Natural Gas Vehicles to someone by E-mail Share Alternative Fuels Data Center: Natural Gas Vehicles on Facebook Tweet about Alternative Fuels Data Center: Natural Gas Vehicles on Twitter Bookmark Alternative
Short-term LNG-markets

International Nuclear Information System (INIS)

Eldegard, Tom; Lund, Arne-Christian; Miltersen, Kristian; Rud, Linda

2005-01-01

The global Liquefied Natural Gas (LNG) industry has experienced substantial growth in the past decades. In the traditional trade patterns of LNG the product has typically been handled within a dedicated chain of plants and vessels fully committed by long term contracts or common ownership, providing risk sharing of large investments in a non-liquid market. Increasing gas prices and substantial cost reductions in all parts of the LNG chain have made LNG projects viable even if only part of the capacity is secured by long-term contracts, opening for more flexible trade of the remainder. Increasing gas demand, especially in power generation, combined with cost reductions in the cost of LNG terminals, open new markets for LNG. For the LNG supplier, the flexibility of shifting volumes between regions represents an additional value. International trade in LNG has been increasing, now accounting for more than one fifth of the world's cross-border gas trade. Despite traditional vertical chain bonds, increased flexibility has contributed in fact to an increasing LNG spot trade, representing 8% of global trade in 2002. The focus of this paper is on the development of global short-term LNG markets, and their role with respect to efficiency and security of supply in European gas markets. Arbitrage opportunities arising from price differences between regional markets (such as North America versus Europe) are important impetuses for flexible short-term trade. However, the short-term LNG trade may suffer from problems related to market access, e.g. limited access to terminals and regulatory issues, as well as rigidities connected to vertical binding within the LNG chain. Important issues related to the role of short-term LNG-trade in the European gas market are: Competition, flexibility in meeting peak demand, security of supply and consequences of differences in pricing policies (oil-linked prices in Europe and spot market prices in North America). (Author)
Thermodynamic analysis of a novel power plant with LNG (liquefied natural gas) cold exergy exploitation and CO_2 capture

International Nuclear Information System (INIS)

Romero Gómez, Manuel; Romero Gómez, Javier; López-González, Luis M.; López-Ochoa, Luis M.

2016-01-01

The LNG (liquefied natural gas) regasification process is a source of cold exergy that is suitable to be recovered to improve the efficiency of thermal power plants. In this paper, an innovative power plant with LNG (liquefied natural gas) exergy utilisation and the capture of CO_2 proceeding from the flue gases is presented. It is characterised by the recovery of LNG cold exergy in a closed Brayton cycle and through direct expansion in an expander coupled to an electrical generator. Moreover, this novel power plant configuration allows CO_2 capture, through an oxy-fuel combustion system and a Rankine cycle that operates with the flue gases themselves and in quasi-critical conditions. The greatest advantage of this plant is that all the recoverable LNG exergy is used to increase the efficiency of the CBC (closed Brayton cycle) and in direct expansion whereas, in other power cycles found in literature that associate LNG regasification and CO_2 capture, part of the LNG exergy is used for condensing flue gas CO_2 for its subsequent capture. As a result, a high efficiency power plant is achieved, exceeding 65%, with almost zero greenhouse gas emissions. - Highlights: • LNG cold exergy can be recovered to improve the efficiency of power plants. • High efficiency power plant with almost zero greenhouse gas emissions. • CO_2 capture through an oxy-fuel combustion system and a Rankine cycle. • Sensitivity analysis of key parameters to evaluate the effect on the efficiency. • The exergy available in the LNG represents 34.79% of the fuel exergy.
H_2 production by the steam reforming of excess boil off gas on LNG vessels

International Nuclear Information System (INIS)

Fernández, Ignacio Arias; Gómez, Manuel Romero; Gómez, Javier Romero; López-González, Luis M.

2017-01-01

Highlights: • BOG excess in LNG vessels is burned in the GCU without energy use. • The gas management plants need to be improved to increase efficiency. • BOG excess in LNG vessels is used for H_2 production by steam reforming. • The availability of different fuels increases the versatility of the ship. - Abstract: The gas management system onboard LNG (Liquid Natural Gas) vessels is crucial, since the exploitation of the BOG (Boil Off Gas) produced is of utmost importance for the overall efficiency of the plant. At present, LNG ships with no reliquefaction plant consume the BOG generated in the engines, and the excess is burned in the GCU (Gas Combustion Unit) without any energy use. The need to improve the gas management system, therefore, is evident. This paper proposes hydrogen production through a steam reforming plant, using the excess BOG as raw material and thus avoiding it being burned in the GCU. To test the feasibility of integrating the plant, an actual study of the gas management process on an LNG vessel with 4SDF (4 Stroke Dual Fuel) propulsion and with no reliquefaction plant was conducted, along with a thermodynamic simulation of the reforming plant. With the proposed gas management system, the vessel disposes of different fuels, including H_2, a clean fuel with zero ozone-depleting emissions. The availability of H_2 on board in areas with strict anti-pollution regulations, such as ECAs (Emission Control Area), means that the vessel may be navigated without using fossil fuels which generate CO_2 and SO_X emissions. Moreover, while at port, Cold Ironing is avoided, which entails high costs. Thus it is demonstrated that the installation of a reforming plant is both energetically viable and provides greater versatility to the ship.
Development of a lightweight fuel cell vehicle

Science.gov (United States)

Hwang, J. J.; Wang, D. Y.; Shih, N. C.

This paper described the development of a fuel cell system and its integration into the lightweight vehicle known as the Mingdao hydrogen vehicle (MHV). The fuel cell system consists of a 5-kW proton exchange membrane fuel cell (PEMFC), a microcontroller and other supported components like a compressed hydrogen cylinder, blower, solenoid valve, pressure regulator, water pump, heat exchanger and sensors. The fuel cell not only propels the vehicle but also powers the supporting components. The MHV performs satisfactorily over a hundred-kilometer drive thus validating the concept of a fuel cell powered zero-emission vehicle. Measurements further show that the fuel cell system has an efficiency of over 30% at the power consumption for vehicle cruise, which is higher than that of a typical internal combustion engine. Tests to improve performance such as speed enhancement, acceleration and fuel efficiency will be conducted in the future work. Such tests will consist of hybridizing with a battery pack.
LNG demand, shipping will expand through 2010

International Nuclear Information System (INIS)

True, W.R.

1998-01-01

The 1990s, especially the middle years, have witnessed a dramatic turnaround in the growth of liquefied-natural-gas demand which has tracked equally strong natural-gas demand growth. This trend was underscored late last year by several annual studies of world LNG demand and shipping. As 1998 began, however, economic turmoil in Asian financial markets has clouded near-term prospects for LNG in particular and all energy in general. But the extent of damage to energy markets is so far unclear. A study by US-based Institute of Gas Technology, Des Plaines, IL, reveals that LNG imports worldwide have climbed nearly 8%/year since 1980 and account for 25% of all natural gas traded internationally. In the mid-1970s, the share was only 5%. In 1996, the most recent year for which complete data are available, world LNG trade rose 7.7% to a record 92 billion cu m, outpacing the overall consumption for natural gas which increased 4.7% in 1996. By 2015, says the IGT study, natural-gas use would surpass coal as the world''s second most widely used fuel, after petroleum. Much of this growth will occur in the developing countries of Asia where gas use, before the current economic crisis began, was projected to grow 8%/year through 2015. Similar trends are reflected in another study of LNG trade released at year end 1997, this from Ocean Shipping Consultants Ltd., Surrey, U.K. The study was done too early, however, to consider the effects of the financial problems roiling Asia
Kitimat LNG Inc

International Nuclear Information System (INIS)

Boulton, R.

2006-01-01

Kitimat LNG terminal is the first fully permitted liquefied natural gas (LNG) on the west coast of Canada and the United States. The terminal was designed to have a small environmental footprint, and has the full support of communities and First Nations groups in the area. Regulatory approvals are now in place, and site construction is planned to start in 2007. This presentation provided details of the facility's gas production and liquefaction processes, shipping, and LNG import and regasification terminals. The site was selected due to its deepwater, all-season port and the fact that the Pacific Trail Pipelines provide access to major transmission lines. The terminal will be comprised of an offshore LNG tanker berth and unloading jetty, a construction and tug berth, 2 LNG storage tanks, a separation unit, and send-out pipelines for natural gas and gas liquids. The terminal was designed for maximum LNG receiving flexibility as it can handle a wide variety of gas specifications and will be able to receive the largest possible LNG tankers. Market interest in the terminal has been considerable as investors are increasingly convinced that LNG can provide long-term supply alternatives to the North American gas market. Once operational the terminal will attract supply from the Pacific basin and the Middle East. Western Canadian gas demand is projected to grow at nearly 6 per cent through 2015. It was concluded that marine safety is crucial to the successful operation of the terminal. Details of safety plans formed after consultation with various organizations were presented. refs., tabs., figs
Outlook on Standardization of Alternative Vehicle Fuels

Energy Technology Data Exchange (ETDEWEB)

Rehnlund, B [Atrax Energi AB (Sweden)

2008-10-15

The use of fossil but in first hand biobased alternative fuels in transportation has increased over the last decades. This change is primarily driven by concerns about climate change that is caused by emissions of fossil carbon dioxide and other greenhouse gases, but also by the impact on health and environment, caused by emissions of regulated as well as non-regulated emissions from the transport sector. Most alternative fuels will help to reduce the emissions of regulated and non-regulated emissions, while alternative fuels based on biomass also will contribute to reduced net emissions of carbon dioxide. Since the mid 1990s, the use of biomass based fuels such as ethanol and biodiesel has reached levels high enough in for example Europe, Brazil and the U.S. to motivate national or regional specifications/standards. Especially from the vehicle/engine manufacturer's point of view standards are of high importance. From early 2000 onwards, the international trade of biofuels (for example from Brazil to the U.S. and Europe) has grown, and this has created a need for common international specifications/standards. This report presents information about national and regional standards for alternative fuels, but also, when existing and reported, standards on a global level are described and discussed. Ongoing work concerning new or revised standards on alternative fuels on national, regional or global level is also discussed. In this report we have covered standards on all kind of alternative fuels, exemplified below. However, the focus is on liquid biofuels for diesel engines and Otto engines. 1) Liquid fuels for diesel engines (compression ignition engines), such as Fatty Acid Methyl Esters (FAME), Fatty Acid Ethyl Esters (FAEE), alcohols, alcohol derivates and synthetic diesel fuels. 2) Liquid fuels for Otto engines (spark ignition engines), such as alcohols, ethers and synthetic gasoline. 3) Liquefied fossil petroleum gas (LPG). 4) Di-Methyl Ether (DME). 5) Fossil

Outlook on Standardization of Alternative Vehicle Fuels

Energy Technology Data Exchange (ETDEWEB)

Rehnlund, B. [Atrax Energi AB (Sweden)

2008-10-15

The use of fossil but in first hand biobased alternative fuels in transportation has increased over the last decades. This change is primarily driven by concerns about climate change that is caused by emissions of fossil carbon dioxide and other greenhouse gases, but also by the impact on health and environment, caused by emissions of regulated as well as non-regulated emissions from the transport sector. Most alternative fuels will help to reduce the emissions of regulated and non-regulated emissions, while alternative fuels based on biomass also will contribute to reduced net emissions of carbon dioxide. Since the mid 1990s, the use of biomass based fuels such as ethanol and biodiesel has reached levels high enough in for example Europe, Brazil and the U.S. to motivate national or regional specifications/standards. Especially from the vehicle/engine manufacturer's point of view standards are of high importance. From early 2000 onwards, the international trade of biofuels (for example from Brazil to the U.S. and Europe) has grown, and this has created a need for common international specifications/standards. This report presents information about national and regional standards for alternative fuels, but also, when existing and reported, standards on a global level are described and discussed. Ongoing work concerning new or revised standards on alternative fuels on national, regional or global level is also discussed. In this report we have covered standards on all kind of alternative fuels, exemplified below. However, the focus is on liquid biofuels for diesel engines and Otto engines. 1) Liquid fuels for diesel engines (compression ignition engines), such as Fatty Acid Methyl Esters (FAME), Fatty Acid Ethyl Esters (FAEE), alcohols, alcohol derivates and synthetic diesel fuels. 2) Liquid fuels for Otto engines (spark ignition engines), such as alcohols, ethers and synthetic gasoline. 3) Liquefied fossil petroleum gas (LPG). 4) Di-Methyl Ether (DME). 5
Current status and future projections of LNG demand and supplies: A global prospective

International Nuclear Information System (INIS)

Kumar, Satish; Kwon, Hyouk-Tae; Choi, Kwang-Ho; Hyun Cho, Jae; Lim, Wonsub; Moon, Il

2011-01-01

An unceasing growth of gas consumption in domestic households, industry, and power plants has gradually turned natural gas into a major source of energy. Main drivers in this development are the technical and economic advantages of natural gas. It is a clean, versatile, and easily controllable fuel. On this basis, natural gas is often considered the form of energy that will be the 'bridging fuel' to a sustainable energy system, sometime after 2050. Unlike other main sources of energy, such as oil and coal, gas is not traded on an actual world market. This paper provides an overview on demand and supplies of natural gas (LNG) in the past as a function of gas prices, gas technology (gas sweetening, liquefaction, shipping and re-gasification), and gas market and how they have changed recently. It also discusses the likely developments in global LNG demand for the period to the year 2030. - Highlights: → This study provides an overview on demand and supplies of LNG in the past and future. → Outlook for LNG demand in Asia pacific region is very robust. → In past decade the shale gas production in USA has increased fivefold. → The future of European gas supply depends largely on the geopolitical environments. → Within the gas sector LNG is playing an ever increasing role in gas transportation.
New developments in LNG trade

International Nuclear Information System (INIS)

Frisch, Morten

2000-01-01

This paper presents an overview of international trade in liquefied natural gas. Factors and forces causing changes in the international LNG market are explored covering Japan and South East Asian markets, the rapidly growing Spanish and Italian markets, competition faced by LNG imports by pipeline gas in France and Belgium, the reopening of mothballed LNG receiving facilities in the US east coast, and markets with large LNG potential in India, China and South America. Developments in the price of LNG in Japan, Europe, and the US east coast are considered, and shipping issues, and future trends in LNG purchase arrangements and LNG pricing are discussed
Fuel cell vehicles: technological solution

International Nuclear Information System (INIS)

Lopez Martinez, J. M.

2004-01-01

Recently it takes a serious look at fuel cell vehicles, a leading candidate for next-generation vehicle propulsion systems. The green house effect and air quality are pressing to the designers of internal combustion engine vehicles, owing to the manufacturers to find out technological solutions in order to increase the efficiency and reduce emissions from the vehicles. On the other hand, energy source used by currently propulsion systems is not renewable, the well are limited and produce CO 2 as a product from the combustion process. In that situation, why fuel cell is an alternative of internal combustion engine?
Leakage analysis of fuel gas pipe in large LNG carrier engine room

Directory of Open Access Journals (Sweden)

CEN Zhuolun

2017-10-01

Full Text Available [Objectives] The electric propulsion dual-fuel engine is becoming dominant in newly built Liquefied Natural Gas(LNGcarriers. To avoid the potential risks that accompany the use of flammable and explosive boil-off gas,the performance of precise safety and reliability assessments is indispensable. [Methods] This research concerns the engine rooms of large LNG carriers which are propelled electrically by a dual-fuel engine. Possible fuel gas(natural gasleak cases in different areas of the engine room are simulated and analyzed. Five representative leak cases defined by leak form,leak location and leak rate are entered into a Computational Fluid Dynamics(CFDsimulation,in which the Reynolds stress model of Fluent software is adopted as the turbulence model. The results of the leaked gas distribution and ventilation velocity field are analyzed in combination to obtain the diffusion tendency and concentration distribution of leaked gas in different areas.[Results] Based on an analysis of the results,an optimized arrangement of flammable gas detectors is provided for the engine room, and the adoption of an explosion-proof exhaust fan is proven to be unnecessary.[Conclusions] These analysis methods can provide a reference for similar gas leakage scenarios occurring in confined ventilated spaces. In addition, the simulation results can be used to quantitatively assess potential fire or explosion damage in order to guide the design of structural reinforcements.
Gasoline-fueled hybrid vs. conventional vehicle emissions and fuel economy.

Energy Technology Data Exchange (ETDEWEB)

Anderson, J.; Bharathan, D.; He, J.; Plotkin, S.; Santini, D.; Vyas, A.

1999-06-18

This paper addresses the relative fuel economy and emissions behavior, both measured and modeled, of technically comparable, contemporary hybrid and conventional vehicles fueled by gasoline, in terms of different driving cycles. Criteria pollutants (hydrocarbons, carbon monoxide, and nitrogen oxides) are discussed, and the potential emissions benefits of designing hybrids for grid connection are briefly considered. In 1997, Toyota estimated that their grid-independent hybrid vehicle would obtain twice the fuel economy of a comparable conventional vehicle on the Japan 10/15 mode driving cycle. This initial result, as well as the fuel economy level (66 mpg), made its way into the U.S. press. Criteria emissions amounting to one-tenth of Japanese standards were cited, and some have interpreted these results to suggest that the grid-independent hybrid can reduce criteria emissions in the U.S. more sharply than can a conventional gasoline vehicle. This paper shows that the potential of contemporary grid-independent hybrid vehicle technology for reducing emissions and fuel consumption under U.S. driving conditions is less than some have inferred. The importance (and difficulty) of doing test and model assessments with comparable driving cycles, comparable emissions control technology, and comparable performance capabilities is emphasized. Compared with comparable-technology conventional vehicles, grid-independent hybrids appear to have no clear criteria pollutant benefits (or disbenefits). (Such benefits are clearly possible with grid-connectable hybrids operating in zero emissions mode.) However, significant reductions in greenhouse gas emissions (i.e., fuel consumption) are possible with hybrid vehicles when they are used to best advantage.
LNG TERMINAL SAFE OPERATION MANAGEMENT

Directory of Open Access Journals (Sweden)

Andrzej ADAMKIEWICZ

2012-07-01

Full Text Available This article presents the significance of LNG terminal safety issues in natural gas sea transport. It shows particular requirements for LNG transmission installations resulting from the specific properties of LNG. Out of the multi‐layer critical safety areas comprising structural elements of the terminal safety system, possibilities to decrease the risk of emergency occurrence on LNG terminals have been selected. Tasks performed by the LNG terminal, together with its own personnel and the outside one, have been defined. General theses for LNG terminal safety have been formulated.
Fuel choices for fuel-cell vehicles : well-to-wheel energy and emission impacts

International Nuclear Information System (INIS)

Wang, M.

2002-01-01

Because of their high energy efficiencies and low emissions, fuel-cell vehicles (FCVs) are undergoing extensive research and development. While hydrogen will likely be the ultimate fuel to power fuel-cell vehicles, because of current infrastructure constraints, hydrogen-carrying fuels are being investigated as transitional fuel-cell fuels. A complete well-to-wheels (WTW) evaluation of fuel-cell vehicle energy and emission effects that examines (1) energy feedstock recovery and transportation; (2) fuel production, transportation, and distribution; and (3) vehicle operation must be conducted to assist decision makers in selecting the fuel-cell fuels that achieve the greatest energy and emission benefits. A fuel-cycle model developed at Argonne National Laboratory--called the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model--was used to evaluate well-to-wheels energy and emission impacts of various fuel-cell fuels. The results show that different fuel-cell fuels can have significantly different energy and greenhouse gas emission effects. Therefore, if fuel-cell vehicles are to achieve the envisioned energy and emission reduction benefits, pathways for producing the fuels that power them must be carefully examined.
Establishing bonds between vehicle certification data and real-world vehicle fuel consumption – A Vehicle Specific Power approach

International Nuclear Information System (INIS)

Duarte, G.O.; Gonçalves, G.A.; Baptista, P.C.; Farias, T.L.

2015-01-01

Highlights: • Innovative methodology to estimate VSP fuel consumption based on public available data. • Model validation with accurate fuel consumption results (absolute deviation from 4.7% to 9.2%). • Best-selling vehicles in Portugal case study was developed for different driving cycles. - Abstract: A method to perform the energy characterization of a vehicle according to the specific power required while driving was developed using public vehicle certification data. Using a portable emission measurement system, fuel consumption was quantified in a second-by-second basis under on-road conditions for 19 vehicles (spark-ignition, compression-ignition and hybrids). This data allowed building generic curves of fuel consumption as a function of the specific power, according to Vehicle Specific Power methodology. Comparing on-road measurements and the model estimates, a R 2 higher than 0.9 for conventional and hybrid vehicles was obtained regarding modal fuel consumption. Comparing the fuel consumption measured on the drive cycles performed by each vehicle and the correspondent estimates, an absolute deviation of 9.2% ± 9.2% was found for conventional vehicles and 4.7% ± 1.8% for hybrids vehicles. This methodology was validated and applied to estimate the energy impacts of the best-selling vehicles in Portugal for different driving cycles. This prompt method, that does not require vehicle monitoring, can estimate curves of fuel consumption in g/s, as a function of specific power, which allows quantifying the absolute fuel use for any driving cycle
Hydrogen Fuel Cell Vehicle Fuel Economy Testing at the U.S. EPA National Vehicle and Fuel Emissions Laboratory (SAE Paper 2004-01-2900)

Science.gov (United States)

The introduction of hydrogen fuel cell vehicles and their new technology has created the need for development of new fuel economy test procedures and safety procedures during testing. The United States Environmental Protection Agency-National Vehicle Fuels and Emissions Laborato...
Fuel-cycle greenhouse gas emissions impacts of alternative transportation fuels and advanced vehicle technologies

International Nuclear Information System (INIS)

Wang, M. Q.

1998-01-01

At an international conference on global warming, held in Kyoto, Japan, in December 1997, the United States committed to reduce its greenhouse gas (GHG) emissions by 7% over its 1990 level by the year 2012. To help achieve that goal, transportation GHG emissions need to be reduced. Using Argonne's fuel-cycle model, I estimated GHG emissions reduction potentials of various near- and long-term transportation technologies. The estimated per-mile GHG emissions results show that alternative transportation fuels and advanced vehicle technologies can help significantly reduce transportation GHG emissions. Of the near-term technologies evaluated in this study, electric vehicles; hybrid electric vehicles; compression-ignition, direct-injection vehicles; and E85 flexible fuel vehicles can reduce fuel-cycle GHG emissions by more than 25%, on the fuel-cycle basis. Electric vehicles powered by electricity generated primarily from nuclear and renewable sources can reduce GHG emissions by 80%. Other alternative fuels, such as compressed natural gas and liquefied petroleum gas, offer limited, but positive, GHG emission reduction benefits. Among the long-term technologies evaluated in this study, conventional spark ignition and compression ignition engines powered by alternative fuels and gasoline- and diesel-powered advanced vehicles can reduce GHG emissions by 10% to 30%. Ethanol dedicated vehicles, electric vehicles, hybrid electric vehicles, and fuel-cell vehicles can reduce GHG emissions by over 40%. Spark ignition engines and fuel-cell vehicles powered by cellulosic ethanol and solar hydrogen (for fuel-cell vehicles only) can reduce GHG emissions by over 80%. In conclusion, both near- and long-term alternative fuels and advanced transportation technologies can play a role in reducing the United States GHG emissions
Fuel-cycle greenhouse gas emissions impacts of alternative transportation fuels and advanced vehicle technologies.

Energy Technology Data Exchange (ETDEWEB)

Wang, M. Q.

1998-12-16

At an international conference on global warming, held in Kyoto, Japan, in December 1997, the United States committed to reduce its greenhouse gas (GHG) emissions by 7% over its 1990 level by the year 2012. To help achieve that goal, transportation GHG emissions need to be reduced. Using Argonne's fuel-cycle model, I estimated GHG emissions reduction potentials of various near- and long-term transportation technologies. The estimated per-mile GHG emissions results show that alternative transportation fuels and advanced vehicle technologies can help significantly reduce transportation GHG emissions. Of the near-term technologies evaluated in this study, electric vehicles; hybrid electric vehicles; compression-ignition, direct-injection vehicles; and E85 flexible fuel vehicles can reduce fuel-cycle GHG emissions by more than 25%, on the fuel-cycle basis. Electric vehicles powered by electricity generated primarily from nuclear and renewable sources can reduce GHG emissions by 80%. Other alternative fuels, such as compressed natural gas and liquefied petroleum gas, offer limited, but positive, GHG emission reduction benefits. Among the long-term technologies evaluated in this study, conventional spark ignition and compression ignition engines powered by alternative fuels and gasoline- and diesel-powered advanced vehicles can reduce GHG emissions by 10% to 30%. Ethanol dedicated vehicles, electric vehicles, hybrid electric vehicles, and fuel-cell vehicles can reduce GHG emissions by over 40%. Spark ignition engines and fuel-cell vehicles powered by cellulosic ethanol and solar hydrogen (for fuel-cell vehicles only) can reduce GHG emissions by over 80%. In conclusion, both near- and long-term alternative fuels and advanced transportation technologies can play a role in reducing the United States GHG emissions.
Hawaii energy strategy project 2: Fossil energy review. Task 3 -- Greenfield options: Prospects for LNG use

Energy Technology Data Exchange (ETDEWEB)

Breazeale, K. [ed.; Fesharaki, F.; Fridley, D.; Pezeshki, S.; Wu, K.

1993-12-01

This paper begins with an overview of the Asia-Pacific LNG market, its major players, and the likely availability of LNG supplies in the region. The discussion then examines the possibilities for the economic supply of LNG to Hawaii, the potential Hawaiian market, and the viability of an LNG project on Oahu. This survey is far from a complete technical assessment or an actual engineering/feasibility study. The economics alone cannot justify LNG`s introduction. The debate may continue as to whether fuel diversification and environmental reasons can outweigh the higher costs. Several points are made. LNG is not a spot commodity. Switching to LNG in Hawaii would require a massive, long-term commitment and substantial investments. LNG supplies are growing very tight in the Asia-Pacific region. Some of the environmental benefits of LNG are not entirely relevant in Hawaii because Hawaii`s air quality is generally excellent. Any air quality benefits may be more than counterbalanced by the environmental hazards connected with large-scale coastal zone construction, and by the safety hazards of LNG carriers, pipelines, etc. Lastly, LNG is not suitable for all energy uses, and is likely to be entirely unsuitable for neighbor island energy needs.
LNG project - contractual aspects

Energy Technology Data Exchange (ETDEWEB)

Goncalves, Bruno Almeida

2008-07-01

This paper intends to provide from the legal point of view an outline of the main challenges of a LNG project in the upstream, regulatory aspects, liquefaction, financing and midstream through a basic checklist; an overview of the contractual complexity of a LNG project; some basic discussion of particular LNG contract clauses; and a comparative analysis between the classic clauses of a Gas Transportation Agreement (GTA) through a gas pipeline and LNG logistic. (author)
Fuel cell mining vehicles: design, performance and advantages

International Nuclear Information System (INIS)

Betournay, M.C.; Miller, A.R.; Barnes, D.L.

2003-01-01

The potential for using fuel cell technology in underground mining equipment was discussed with reference to the risks associated with the operation of hydrogen vehicles, hydrogen production and hydrogen delivery systems. This paper presented some of the initiatives for mine locomotives and fuel cell stacks for underground environments. In particular, it presents the test results of the first applied industrial fuel cell vehicle in the world, a mining and tunneling locomotive. This study was part of an international initiative managed by the Fuel Cell Propulsion Institute which consists of several mining companies, mining equipment manufacturers, and fuel cell technology developers. Some of the obvious benefits of fuel cells for underground mining operations include no exhaust gases, lower electrical costs, significantly reduced maintenance, and lower ventilation costs. Another advantage is that the technology can be readily automated and computer-based for tele-remote operations. This study also quantified the cost and operational benefits associated with fuel cell vehicles compared to diesel vehicles. It is expected that higher vehicle productivity could render fuel cell underground vehicles cost-competitive. 6 refs., 1 tab
Monitoring and analysis of liquid storage in LNG tank based on different support springs

Science.gov (United States)

He, Hua; Sun, Jianping; Li, Ke; Wu, Zheng; Chen, Qidong; Chen, Guodong; Cao, Can

2018-04-01

With the rapid development of social modernization, LNG vehicles are springing up in daily life. However, it is difficult to monitor and judge the liquid storage tanks accurately and quickly. Based on this, this paper presents a new method of liquid storage monitoring, LNG tank on-line vibration monitoring system. By collecting the vibration frequency of LNG tank and tank liquid and supporting spring system, the liquid storage quality in the tank can be calculated. In this experiment, various vibration modes of the tank spring system are fully taken into account. The vibration effects of different types of support springs on the LNG tank system were investigated. The results show that the spring model has a great influence on the test results. This study provides a technical reference for the selection of suitable support springs for liquid storage monitoring.
LNG Safety Assessment Evaluation Methods

Energy Technology Data Exchange (ETDEWEB)

Muna, Alice Baca [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); LaFleur, Angela Christine [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-05-01

Sandia National Laboratories evaluated published safety assessment methods across a variety of industries including Liquefied Natural Gas (LNG), hydrogen, land and marine transportation, as well as the US Department of Defense (DOD). All the methods were evaluated for their potential applicability for use in the LNG railroad application. After reviewing the documents included in this report, as well as others not included because of repetition, the Department of Energy (DOE) Hydrogen Safety Plan Checklist is most suitable to be adapted to the LNG railroad application. This report was developed to survey industries related to rail transportation for methodologies and tools that can be used by the FRA to review and evaluate safety assessments submitted by the railroad industry as a part of their implementation plans for liquefied or compressed natural gas storage ( on-board or tender) and engine fueling delivery systems. The main sections of this report provide an overview of various methods found during this survey. In most cases, the reference document is quoted directly. The final section provides discussion and a recommendation for the most appropriate methodology that will allow efficient and consistent evaluations to be made. The DOE Hydrogen Safety Plan Checklist was then revised to adapt it as a methodology for the Federal Railroad Administration’s use in evaluating safety plans submitted by the railroad industry.
LNG TERMINAL SAFE OPERATION MANAGEMENT

OpenAIRE

Andrzej ADAMKIEWICZ; Włodzimierz KAMIŃSKI

2012-01-01

This article presents the significance of LNG terminal safety issues in natural gas sea transport. It shows particular requirements for LNG transmission installations resulting from the specific properties of LNG. Out of the multi‐layer critical safety areas comprising structural elements of the terminal safety system, possibilities to decrease the risk of emergency occurrence on LNG terminals have been selected. Tasks performed by the LNG terminal, together with its own personnel and the out...
The LNG Industry - 2014

International Nuclear Information System (INIS)

Dispenza, Domenico

2015-04-01

destination and pricing. LNG players' quest for flexible volumes and volume risk mitigation has contributed to a multiplication of portfolio deals last year, mainly for short to medium-term durations. In parallel, the addition of flexible quantities with a lengthening of trade voyages and the entry of new players results in the need for an expansion of the LNG fleet - with 77 new orders placed in 2014 - compared to a total fleet of 421 at year-end. Meanwhile, the Ukraine-Russia crisis and the start-up of six new re-gasification terminals worldwide reminds us that LNG is an effective tool to ensure security of supply. In this regard FSRUs are continuing to expand worldwide, with 20 units on the water at the end of 2014 and several more to come in 2015. 3 FIDs have been taken in 2014, namely Cameron and Freeport in the USA and Rotan FLNG in Malaysia, for a combined capacity of about 25 mtpa. Although not formally announced at the time of this writing, Cove Point is reported to have started construction work on site. Prospects for LNG demand throughout the world remain strong, and the industry is waiting for the wave of new exports from the United States and from Australia, who will likely top the producers' list by 2020. Noteworthy is also that the dominant market share and role of Middle East producers will diminish. The structure of demand should also evolve, mainly driven by the emergence of new importers from fast growing economies in South East Asia and in India. China's appetite for gas will significantly influence the global LNG market, although several uncertainties remain concerning the price elasticity of demand, the policy changes promoting cleaner fuels and the competition of large gas pipeline projects. Finally, stricter legislation on shipping emissions starting in January 2015 in the Atlantic basin will help stimulating the development of small scale LNG, offering new opportunities of growth as well as new challenges
The LNG Industry - 2008

International Nuclear Information System (INIS)

2009-04-01

Estimates for the marketed production of natural gas in 2008 show a rise of about 3.4% over 2007. The share of LNG in the gas trade accounts for 27% of the total (excluding trade within the Former Soviet Union and United Arab Emirates). This annual report presents: 1 - LNG contracts and trade, 2 - Contracts concluded in 2008, 3 - LNG imports - Sources of imports - Quantities received in 2008, 4 - LNG tankers, 5 - Ships delivered, 6 - Tanker distribution, 7 - Liquefaction plants, 8 - re-gasification plants, 9 - Contracts in force in 2008, 10 - Spot and short term quantities received in 2008, 11 - Sea transportation routes, 12 - Liquefaction plants (table), 13 - re-gasification plants (table), 14 - Delivery date of the LNG tankers

The LNG Industry - 2009

International Nuclear Information System (INIS)

2010-04-01

Estimates for the marketed production of natural gas in 2009 show a decrease of about 3.9% over 2008. The share of LNG in the gas trade accounts for 30% of the total (excluding trade within the Former Soviet Union and United Arab Emirates). This annual report presents: 1 - LNG contracts and trade, 2 - Contracts concluded in 2009, 3 - LNG imports - Sources of imports - Quantities received in 2009, 4 - LNG tankers, 5 - Ships delivered, 6 - Tanker distribution, 7 - Liquefaction plants, 8 - re-gasification plants, 9 - Contracts in force in 2009, 10 - Spot and short term quantities received in 2009, 11 - Sea transportation routes, 12 - Liquefaction plants (table), 13 - re-gasification plants (table), 14 - Delivery date of the LNG tankers
PIF4 Promotes Expression of LNG1 and LNG2 to Induce Thermomorphogenic Growth in Arabidopsis

Directory of Open Access Journals (Sweden)

Geonhee Hwang

2017-07-01

Full Text Available Arabidopsis plants adapt to high ambient temperature by a suite of morphological changes including elongation of hypocotyls and petioles and leaf hyponastic growth. These morphological changes are collectively called thermomorphogenesis and are believed to increase leaf cooling capacity by enhancing transpiration efficiency, thereby increasing tolerance to heat stress. The bHLH transcription factor PHYTOCHROME INTERACTING FACTOR4 (PIF4 has been identified as a major regulator of thermomorphogenic growth. Here, we show that PIF4 promotes the expression of two homologous genes LONGIFOLIA1 (LNG1 and LONGIFOLIA2 (LNG2 that have been reported to regulate leaf morphology. ChIP-Seq analyses and ChIP assays showed that PIF4 directly binds to the promoters of both LNG1 and LNG2. The expression of LNG1 and LNG2 is induced by high temperature in wild type plants. However, the high temperature activation of LNG1 and LNG2 is compromised in the pif4 mutant, indicating that PIF4 directly regulates LNG1 and LNG2 expression in response to high ambient temperatures. We further show that the activities of LNGs support thermomorphogenic growth. The expression of auxin biosynthetic and responsive genes is decreased in the lng quadruple mutant, implying that LNGs promote thermomorphogenic growth by activating the auxin pathway. Together, our results demonstrate that LNG1 and LNG2 are directly regulated by PIF4 and are new components for the regulation of thermomorphogenesis.
Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel

Science.gov (United States)

Biodiesel Printable Version Share this resource Send a link to Alternative Fuels Data Center : Diesel Vehicles Using Biodiesel to someone by E-mail Share Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel on Facebook Tweet about Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel
Optimization of Fuel Cell System Operating Conditions for Fuel Cell Vehicles

OpenAIRE

Zhao, Hengbing; Burke, Andy

2008-01-01

Proton Exchange Membrane fuel cell (PEMFC) technology for use in fuel cell vehicles and other applications has been intensively developed in recent decades. Besides the fuel cell stack, air and fuel control and thermal and water management are major challenges in the development of the fuel cell for vehicle applications. The air supply system can have a major impact on overall system efficiency. In this paper a fuel cell system model for optimizing system operating conditions was developed wh...
Alternative Fuels Data Center: Hybrid Electric Vehicles

Science.gov (United States)

. A wide variety of hybrid electric vehicle models is currently available. Although HEVs are often -go traffic), further improving fuel economy. Mild hybrid systems cannot power the vehicle using Hybrid Electric Vehicles to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric
Small Scale LNG in Europe

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-09-15

The conference has 19 presentation that addresses topics within the economic and marketing aspects, distribution and transmission, size, operation and design of LNG production units, transportation aspects, technology assessment, storage of LNG and risk and safety aspects of the use and production of LNG. Some LNG application cases are also presented.
Small Scale LNG in Europe

International Nuclear Information System (INIS)

2005-09-01

The conference has 19 presentation that addresses topics within the economic and marketing aspects, distribution and transmission, size, operation and design of LNG production units, transportation aspects, technology assessment, storage of LNG and risk and safety aspects of the use and production of LNG. Some LNG application cases are also presented
Risk-based determination of design pressure of LNG fuel storage tanks based on dynamic process simulation combined with Monte Carlo method

International Nuclear Information System (INIS)

Noh, Yeelyong; Chang, Kwangpil; Seo, Yutaek; Chang, Daejun

2014-01-01

This study proposes a new methodology that combines dynamic process simulation (DPS) and Monte Carlo simulation (MCS) to determine the design pressure of fuel storage tanks on LNG-fueled ships. Because the pressure of such tanks varies with time, DPS is employed to predict the pressure profile. Though equipment failure and subsequent repair affect transient pressure development, it is difficult to implement these features directly in the process simulation due to the randomness of the failure. To predict the pressure behavior realistically, MCS is combined with DPS. In MCS, discrete events are generated to create a lifetime scenario for a system. The combination of MCS with long-term DPS reveals the frequency of the exceedance pressure. The exceedance curve of the pressure provides risk-based information for determining the design pressure based on risk acceptance criteria, which may vary with different points of view. - Highlights: • The realistic operation scenario of the LNG FGS system is estimated by MCS. • In repeated MCS trials, the availability of the FGS system is evaluated. • The realistic pressure profile is obtained by the proposed methodology. • The exceedance curve provides risk-based information for determining design pressure
The LNG Industry - 2007

International Nuclear Information System (INIS)

2008-04-01

Estimates for the marketed production of natural gas in 2007 show a rise of about 1.6% over 2006. The share of LNG in the gas trade accounts for almost 24% of the total. This annual report presents: 1 - LNG contracts and trade, 2 - Contracts concluded in 2007, 3 - LNG imports - Sources of imports - Quantities received in 2007, 4 - LNG tankers, 5 - 35 Ships delivered 10 2007, 6 - Tanker distribution, 7 - Liquefaction plants, 8 - re-gasification plants, 9 - Long-term and medium-term contracts in force in 2007, 10 - Spot and short term quantities received in 2007 by the importing countries from the exporting countries, 11 - Sea transportation routes, 12 - Liquefaction plants (table), 13 - re-gasification plants (table), 14 - Delivery date of the LNG tankers
Training simulator for operations at LNG terminals

International Nuclear Information System (INIS)

Tsuta, T.; Yamamoto, K.; Tetsuka, S.; Koyama, K.

1997-01-01

The Tokyo Gas LNG terminals are among the major energy centers of the Tokyo area, supplying 8 million customers with city gas, and also supplying fuel for thermal power generation at the neighboring thermal power plant operated by the Tokyo Electric Power Company. For this reason, in the event of an emergency at the terminal operators have to be able to respond quickly and accurately to restore operations and prevent secondary damage. Modern LNG terminals are highly reliable and are equipped with backup systems, and occurrences of major trouble are now almost nil. Operators therefore have to be trained to respond to emergencies using simulators, in order to heighten their emergency response capabilities. Tokyo Gas Co., Ltd. has long been aware of the need for simulators and has used them in training, but a new large-scale, real-time simulator has now developed in response to new training needs, applying previously accumulated expertise to create a model of an entire LNG terminal incorporating new features. The development of this new simulator has made possible training for emergencies affecting an entire terminal, and this has been very effective in raising the standards of operators. (au)
Effects of lng Mutations on LngA Expression, Processing, and CS21 Assembly in Enterotoxigenic Escherichia coli E9034A

Science.gov (United States)

Saldaña-Ahuactzi, Zeus; Rodea, Gerardo E.; Cruz-Córdova, Ariadnna; Rodríguez-Ramírez, Viridiana; Espinosa-Mazariego, Karina; González-Montalvo, Martín A.; Ochoa, Sara A.; González-Pedrajo, Bertha; Eslava-Campos, Carlos A.; López-Villegas, Edgar O.; Hernández-Castro, Rigoberto; Arellano-Galindo, José; Patiño-López, Genaro; Xicohtencatl-Cortes, Juan

2016-01-01

Enterotoxigenic Escherichia coli (ETEC) is a major cause of morbidity in children under 5 years of age in low- and middle-income countries and a leading cause of traveler's diarrhea worldwide. The ability of ETEC to colonize the intestinal epithelium is mediated by fimbrial adhesins, such as CS21 (Longus). This adhesin is a type IVb pilus involved in adherence to intestinal cells in vitro and bacterial self-aggregation. Fourteen open reading frames have been proposed to be involved in CS21 assembly, hitherto only the lngA and lngB genes, coding for the major (LngA) and minor (LngB) structural subunit, have been characterized. In this study, we investigated the role of the LngA, LngB, LngC, LngD, LngH, and LngP proteins in the assembly of CS21 in ETEC strain E9034A. The deletion of the lngA, lngB, lngC, lngD, lngH, or lngP genes, abolished CS21 assembly in ETEC strain E9034A and the adherence to HT-29 cells was reduced 90%, compared to wild-type strain. Subcellular localization prediction of CS21 proteins was similar to other well-known type IV pili homologs. We showed that LngP is the prepilin peptidase of LngA, and that ETEC strain E9034A has another peptidase capable of processing LngA, although with less efficiency. Additionally, we present immuno-electron microscopy images to show that the LngB protein could be localized at the tip of CS21. In conclusion, our results demonstrate that the LngA, LngB, LngC, LngD, LngH, and LngP proteins are essential for CS21 assembly, as well as for bacterial aggregation and adherence to HT-29 cells. PMID:27536289
Technology Roadmap: Fuel Economy of Road Vehicles

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

This roadmap explores the potential improvement of existing technologies to enhance the average fuel economy of motorised vehicles; the roadmap’s vision is to achieve a 30% to 50% reduction in fuel use per kilometre from new road vehicles including 2-wheelers, LDV s and HDV s) around the world in 2030, and from the stock of all vehicles on the road by 2050. This achievement would contribute to significant reductions in GHG emissions and oil use, compared to a baseline projection. Different motorised modes are treated separately, with a focus on LDV s, HDV s and powered two-wheelers. A section on in-use fuel economy also addresses technical and nontechnical parameters that could allow fuel economy to drastically improve over the next decades. Technology cost analysis and payback time show that significant progress can be made with low or negative cost for fuel-efficient vehicles over their lifetime use. Even though the latest data analysed by the IEA for fuel economy between 2005 and 2008 showed that a gap exists in achieving the roadmap’s vision, cutting the average fuel economy of road motorised vehicles by 30% to 50% by 2030 is achievable, and the policies and technologies that could help meet this challenge are already deployed in many places around the world.
Fifty years of fuel quality and vehicle emissions

Energy Technology Data Exchange (ETDEWEB)

Rose, K. [CONCAWE, Brussels (Belgium)

2013-04-01

In the late 1970s, with growing emphasis on urban air quality in Europe, CONCAWE embarked on new research related to fuels and vehicles. After only a few years, it became clear that fuel properties and specifications would be increasingly important to the future of the European refining industry, and considerable research was completed in the 1970s to better understand the impact of fuel composition on vehicle performance and emissions. This early work led to the formation of the first Fuels and Emissions Management Group (FEMG) in 1982, almost 20 years after the formation of the CONCAWE Association. Since these early days, FEMG has been responsible for ensuring CONCAWE's strategic outlook on future vehicle and fuel developments, monitoring regulatory and vehicle developments, and overseeing a diverse portfolio of fuel quality and vehicle emissions research. Since the 1980s, tremendous progress has been made in improving European air quality, in part by reducing emissions from road transport and other sectors, and major improvements in European fuel qualities have contributed to these reductions. Nevertheless, many challenges are still ahead, especially further reductions in pollutant emissions from vehicles while also reducing greenhouse gas (GHG) emissions from transport. In the near-term, these GHG reductions will largely come from improvements in engine and vehicle fuel consumption and by blending of GHG-reducing bio-blending components. Dealing with these challenges to fuel quality and performance will require a continuing focus on CONCAWE's founding principles: sound science, cost effectiveness and transparency.
The LNG Industry - 2005

International Nuclear Information System (INIS)

2006-04-01

First estimates for the marketed production of natural gas in 2005 show a rise of about 1.5 % over 2004. The share of LNG in the gas trade accounts for almost 21 % of the total. This annual report presents: 1 - LNG contracts and trade, 2 - Contracts concluded in 2005, 3 - LNG imports - Sources of imports - Quantities received in 2005 by the importing countries from the exporting countries, 4 - LNG tankers, 5 - 18 Ships delivered in 2005, 6 - Tanker distribution, 7 - Liquefaction plants, 8 - re-gasification plants, 9 - Long-term and medium-term contracts in force in 2005, 10 - Spot and short term quantities received in 2005 by the importing countries from the exporting countries, 11 - Sea transportation routes, 12 - Liquefaction plants (table), 13 - re-gasification plants (table), 14 - Delivery date of the LNG tankers
US North Slope gas and Asian LNG markets

Science.gov (United States)

Attanasi, E.D.

1994-01-01

Prospects for export of liquified natural gas (LNG) from Alaska's North Slope are assessed. Projected market conditions to 2010 show that new LNG capacity beyond announced expansions will be needed to meet regional demand and that supplies will probably come from outside the region. The estimated delivered costs of likely suppliers show that Alaska North Slope gas will not be competitive. The alternative North Slope gas development strategies of transport and sale to the lower 48 states and use on the North Slope for either enhanced oil recovery or conversion to liquids are examined. The alternative options require delaying development until US gas prices increase, exhaustion of certain North Slope oil fields, or advances occur in gas to liquid fuels conversion technology. ?? 1995.
Hydrogen Fuel Cell Vehicles

OpenAIRE

Anton Francesch, Judit

1992-01-01

Hydrogen is an especially attractive transportation fuel. It is the least polluting fuel available, and can be produced anywhere there is water and a clean source of electricity. A fuel cycle in which hydrogen is produced by solar-electrolysis of water, or by gasification of renewably grown biomass, and then used in a fuel-cell powered electric-motor vehicle (FCEV), would produce little or no local, regional, or global pollution. Hydrogen FCEVs would combine the best features of bat...
LIQUIFIED NATURAL GAS (LNG CARRIERS

Directory of Open Access Journals (Sweden)

Daniel Posavec

2010-12-01

Full Text Available Modern liquefied natural gas carriers are double-bottom ships classified according to the type of LNG tank. The tanks are specially designed to store natural gas cooled to -161°C, the boiling point of methane. Since LNG is highly flammable, special care must be taken when designing and operating the ship. The development of LNG carriers has begun in the middle of the twentieth century. LNG carrier storage space has gradually grown to the current maximum of 260000 m3. There are more than 300 LNG carriers currently in operation (the paper is published in Croatian.
The LNG Industry - 2004

International Nuclear Information System (INIS)

2005-04-01

First estimates for the marketed production of natural gas in 2004 show a rise of about 2 % over 2003. The share of LNG in the gas trade accounts for 21.9 % of the total. This annual report presents: 1 - LNG contracts and trade, 2 - Contracts concluded in 2004, 3 - LNG imports - Sources of imports - Quantities received in 2005 by the importing countries from the exporting countries, 4 - LNG tankers, 5 - 21 Ships delivered in 2004, 6 - Tanker distribution (at the end of 2004), 7 - Liquefaction plants, 8 - re-gasification plants, 9 - Long-term and medium-term contracts in force in 2004, 10 - Spot and short term quantities received in 2004 by the importing countries from the exporting countries, 11 - Sea transportation routes, 12 - Liquefaction plants (table), 13 - re-gasification plants (table), 14 - Delivery date of the LNG tankers
LNG - the challenge of growth

International Nuclear Information System (INIS)

Summers, G.G.

1992-01-01

LNG growth prospects - both in the Far East and Atlantic Basin - have never been better. Natural gas is responding strongly to the green momentum and to its clear competitive advantage in power generation. To meet growing demand, the major energy buyers are turning increasingly to large remote reserves of gas which often can only be delivered as LNG. But, the market will decide when and which LNG projects are developed - and the trigger will be price. LNG will compete head-on not only with low priced oil and coal but, in some markets, also with long-haul pipeline gas. This paper outlines regional demand and supply opportunities for LNG and then considers the challenges that the LNG industry must now tackle if it is to realistically expect a larger share of the world's energy market
Key issues considered at LNG 13

International Nuclear Information System (INIS)

Kidd, S.

2001-01-01

In the past few years, deregulation of the gas markets throughout the world has changed the way LNG projects can be brought into realisation. Gone are the days when large consortia of buyers could aggregate demand into quantities that made an LNG project economic. Today's market is typified by buyers requesting greater flexibility in volumes, shorter contract terms and reduced exposure to take-or-pay clauses. This means that the onus is on the producer to aggregate volume to make a large project viable, and to find flexible supply options as demand increases. As a result, there is an increasing ability to source LNG from excess capacity around the world, as has been demonstrated with the extended shutdown of the Arun LNG plant in Indonesia. Although some flexibility exists for the supply of LNG, it is unlikely that a world market where LNG is freely traded will develop. LNG projects will still require long-term contracts to ensure project financing. Furthermore, the 'LNG world' will remain separated into two regions the Atlantic and Asia-Pacific basins with only small amounts of 'spot' trading occurring between them. This is primarily due to the increased shipping costs associated with the global movement of LNG, and thus the ability to compete with closer sources of LNG and pipeline gas. Australia's position and its challenges in the LNG market is analysed

Techno-economic assessment of fuel cell vehicles for India

International Nuclear Information System (INIS)

Manish S; Rangan Banerjee

2006-01-01

This paper compares four alternative vehicle technologies for a typical small family car in India (Maruti 800) - two conventional i) Petrol driven internal combustion (IC) engine, ii) Compressed natural gas (CNG) driven IC engine and two based on proton exchange membrane (PEM) fuel cells with different storage iii) Compressed hydrogen storage and iv) Metal hydride (FeTi) storage. Each technology option is simulated in MATLAB using a backward facing algorithm to calculate the force and power requirement for the Indian urban drive cycle. The storage for the CNG and the fuel cell vehicles is designed to have driving range of 50% of the existing petrol vehicle. The simulation considers the part load efficiency vs. load characteristics for the computed ratings of the IC engine and the fuel cell. The analysis includes the transmission efficiency, motor efficiency and storage efficiencies. The comparison criteria used are the primary energy consumption (MJ/km), the cost (Rs./km) obtained by computing the annualized life cycle cost and dividing this by the annual vehicle travel and carbon dioxide emissions (g/km). For the primary energy analysis the energy required for extraction, processing of the fuel is also included. For the fuel cell vehicles, it is assumed that hydrogen is produced from natural gas through steam methane reforming. It is found that the fuel cell vehicles have the lowest primary energy consumption (1.3 MJ/km) as compared to the petrol and CNG vehicles (2.3 and 2.5 MJ/km respectively). The cost analysis is done based on existing prices in India and reveals that the CNG vehicle has the lowest cost (2.3 Rs./km) as compared to petrol (4.5 Rs./km). The fuel cell vehicles have a higher cost of 26 Rs./km mainly due to the higher fuel cell system cost (93% of the total cost). The CO 2 emissions are lowest for the fuel cell vehicle with compressed hydrogen storage (98 g/km) as compared to the petrol vehicle (162 g/km). If the incremental annual cost of the fuel
Well-to-wheels analysis of fuel-cell vehicle/fuel systems

International Nuclear Information System (INIS)

Wang, M.

2002-01-01

Major automobile companies worldwide are undertaking vigorous research and development efforts aimed at developing fuel-cell vehicles (FCVs). Proton membrane exchange (PEM)-based FCVs require hydrogen (H(sub 2)) as the fuel-cell (FC) fuel. Because production and distribution infrastructure for H(sub 2) off board FCVs as a transportation fuel does not exist yet, researchers are developing FCVs that can use hydrocarbon fuels, such as methanol (MeOH) and gasoline, for onboard production of H(sub 2) via fuel processors. Direct H(sub 2) FCVs have no vehicular emissions, while FCVs powered by hydrocarbon fuels have near-zero emissions of criteria pollutants and some carbon dioxide (CO(sub 2)) emissions. However, production of H(sub 2) can generate a large amount of emissions and suffer significant energy losses. A complete evaluation of the energy and emission impacts of FCVs requires an analysis of energy use and emissions during all stages, from energy feedstock wells to vehicle wheels-a so-called ''well-to-wheels'' (WTW) analysis. This paper focuses on FCVs powered by several transportation fuels. Gasoline vehicles (GVs) equipped with internal combustion engines (ICEs) are the baseline technology to which FCVs are compared. Table 1 lists the 13 fuel pathways included in this study. Petroleum-to-gasoline (with 30-ppm sulfur[S] content) is the baseline fuel pathway for GVs
Ansaldo programs on fuel cell vehicles

Energy Technology Data Exchange (ETDEWEB)

Marcenaro, B.G.; Federici, F. [Ansaldo Ricerche Srl, Genova (Italy)

1996-12-31

The growth in traffic and the importance of maintaining a stable ecology at the global scale, particularly with regard to atmospheric pollution, raises the necessity to realize a new generation of vehicles which are more efficient, more economical and compatible with the environment. At European level, the Car of Tomorrow task force has identified fuel cells as a promising alternative propulsion system. Ansaldo Ricerche has been involved in the development of fuel cell vehicles since the early nineties. Current ongoing programs relates to: (1) Fuel cell bus demonstrator (EQHEPP BUS) Test in 1996 (2) Fuel cell boat demonstrator (EQHHPP BOAT) Test in 1997 (3) Fuel cell passenger car prototype (FEVER) Test in 1997 (4) 2nd generation Fuel cell bus (FCBUS) 1996-1999 (5) 2nd generation Fuel cell passenger car (HYDRO-GEN) 1996-1999.
Modeling of hybrid vehicle fuel economy and fuel engine efficiency

Science.gov (United States)

Wu, Wei

"Near-CV" (i.e., near-conventional vehicle) hybrid vehicles, with an internal combustion engine, and a supplementary storage with low-weight, low-energy but high-power capacity, are analyzed. This design avoids the shortcoming of the "near-EV" and the "dual-mode" hybrid vehicles that need a large energy storage system (in terms of energy capacity and weight). The small storage is used to optimize engine energy management and can provide power when needed. The energy advantage of the "near-CV" design is to reduce reliance on the engine at low power, to enable regenerative braking, and to provide good performance with a small engine. The fuel consumption of internal combustion engines, which might be applied to hybrid vehicles, is analyzed by building simple analytical models that reflect the engines' energy loss characteristics. Both diesel and gasoline engines are modeled. The simple analytical models describe engine fuel consumption at any speed and load point by describing the engine's indicated efficiency and friction. The engine's indicated efficiency and heat loss are described in terms of several easy-to-obtain engine parameters, e.g., compression ratio, displacement, bore and stroke. Engine friction is described in terms of parameters obtained by fitting available fuel measurements on several diesel and spark-ignition engines. The engine models developed are shown to conform closely to experimental fuel consumption and motored friction data. A model of the energy use of "near-CV" hybrid vehicles with different storage mechanism is created, based on simple algebraic description of the components. With powertrain downsizing and hybridization, a "near-CV" hybrid vehicle can obtain a factor of approximately two in overall fuel efficiency (mpg) improvement, without considering reductions in the vehicle load.
Liquefied Natural Gas for Trucks and Buses

International Nuclear Information System (INIS)

James Wegrzyn; Michael Gurevich

2000-01-01

Liquefied natural gas (LNG) is being developed as a heavy vehicle fuel. The reason for developing LNG is to reduce our dependency on imported oil by eliminating technical and costs barriers associated with its usage. The U.S. Department of Energy (DOE) has a program, currently in its third year, to develop and advance cost-effective technologies for operating and refueling natural gas-fueled heavy vehicles (Class 7-8 trucks). The objectives of the DOE Natural Gas Vehicle Systems Program are to achieve market penetration by reducing vehicle conversion and fuel costs, to increase consumer acceptance by improving the reliability and efficiency, and to improve air quality by reducing tailpipe emissions. One way to reduce fuel costs is to develop new supplies of cheap natural gas. Significant progress is being made towards developing more energy-efficient, low-cost, small-scale natural gas liquefiers for exploiting alternative sources of natural gas such as from landfill and remote gas sites. In particular, the DOE program provides funds for research and development in the areas of; natural gas clean up, LNG production, advanced vehicle onboard storage tanks, improved fuel delivery systems and LNG market strategies. In general, the program seeks to integrate the individual components being developed into complete systems, and then demonstrate the technology to establish technical and economic feasibility. The paper also reviews the importance of cryogenics in designing LNG fuel delivery systems
LNG As an Alternative Energy Supply in Sweden

Energy Technology Data Exchange (ETDEWEB)

Hansson, Jens [Lund Univ., Dept. of Chemical Engineering, Lund (Sweden)

2008-11-15

As well as summarising the possible alternatives, environmental aspects and uses of LNG, this study aims to investigate the cost involved in the import of LNG to Sweden, from well to user. In Sweden, Natural Gas is used to cover 2 % of the total energy input. The pipeline network stretches from Malmoe to Stenungsund and Gnosjoe, which means some of the most densely populated areas are covered, but there is still 1200 km of the country left, including larger cities such as Stockholm, Uppsala and Linkoeping as well as areas that host some of the most energy demanding industries, e.g. Sundsvall, Umeaa, Luleaa and Kiruna. The absence of Natural Gas typically causes these regions to rely on fuel oil, coke or coal. If these sources of energy could be replaced by Natural Gas, great environmental benefits could be achieved. Research shows that the use of Natural Gas adds 20 % less CO{sub 2} to the atmosphere than oil and also mean lower emissions of NO{sub x}, SO{sub 2} and particles, making it the better alternative from both local and global perspectives. LNG is potentially a fire and an explosion hazard, but in the last 45 years of usage, no major accidents have occurred. Major exporters of LNG are Indonesia, Quatar, Australia and Algeria. Some of the largest importers are Japan, USA, France and Spain. Japan imports nearly 100 % of their Natural Gas as LNG. The available LNG liquefaction capacity increased by 60 % between 2002 and 2007. The total import cost for LNG includes the purchase cost from the producer, the transport cost, be it sea, railroad or road transport, and the cost for the terminal which receives and stores LNG. The study of different routes, volumes and means of transport creates a picture of how the total cost varies in proportion to these parameters. In the calculation of these costs, sources from the industry or estimations of purchase prices, transport costs and terminal costs are used. The uncertainties in this study are especially high when it
LNG As an Alternative Energy Supply in Sweden

Energy Technology Data Exchange (ETDEWEB)

Hansson, Jens (Lund Univ., Dept. of Chemical Engineering, Lund (Sweden))

2008-11-15

As well as summarising the possible alternatives, environmental aspects and uses of LNG, this study aims to investigate the cost involved in the import of LNG to Sweden, from well to user. In Sweden, Natural Gas is used to cover 2 % of the total energy input. The pipeline network stretches from Malmoe to Stenungsund and Gnosjoe, which means some of the most densely populated areas are covered, but there is still 1200 km of the country left, including larger cities such as Stockholm, Uppsala and Linkoeping as well as areas that host some of the most energy demanding industries, e.g. Sundsvall, Umeaa, Luleaa and Kiruna. The absence of Natural Gas typically causes these regions to rely on fuel oil, coke or coal. If these sources of energy could be replaced by Natural Gas, great environmental benefits could be achieved. Research shows that the use of Natural Gas adds 20 % less CO{sub 2} to the atmosphere than oil and also mean lower emissions of NO{sub x}, SO{sub 2} and particles, making it the better alternative from both local and global perspectives. LNG is potentially a fire and an explosion hazard, but in the last 45 years of usage, no major accidents have occurred. Major exporters of LNG are Indonesia, Quatar, Australia and Algeria. Some of the largest importers are Japan, USA, France and Spain. Japan imports nearly 100 % of their Natural Gas as LNG. The available LNG liquefaction capacity increased by 60 % between 2002 and 2007. The total import cost for LNG includes the purchase cost from the producer, the transport cost, be it sea, railroad or road transport, and the cost for the terminal which receives and stores LNG. The study of different routes, volumes and means of transport creates a picture of how the total cost varies in proportion to these parameters. In the calculation of these costs, sources from the industry or estimations of purchase prices, transport costs and terminal costs are used. The uncertainties in this study are especially high when it
Potential local use of natural gas or LNG from Hammerfest LNG plant

International Nuclear Information System (INIS)

Neeraas, Bengt Olav

1999-01-01

A base-load LNG plant is planned to be built in Norway, near by the northern most city in the world, Hammerfest. Natural gas from the Snoehvit-field will be transported by pipeline to Melkoeya, a few kilometres from Hammerfest, where the liquefaction plant is planned to be located. SINTEF Energy Research has performed a study in co-operation with the local authorities on potentials for the use of LNG and natural gas locally in the Hammerfest region. Combined power and heat production by lean-burn gas engine, low temperature freezing of high quality products by use of LNG cold and drying of fish products are some of the identified fields for the use of natural gas and LNG. The establishment of an industrial area, with fish processing industry and a central freezing storage near by Hammerfest has been suggested. The gas may be transported locally either as LNG, by tank lorry or container, or as gas in a small pipeline, depending on distance, amount and the actual use. (author)
Near-optimal operation of dual-fuel launch vehicles

International Nuclear Information System (INIS)

Ardema, M.D.; Chou, H.C.; Bowles, J.V.

1994-01-01

Current studies of single-stage-to-orbit (SSTO) launch vehicles are focused on all-rocket propulsion systems. One option for such vehicles is the use of dual-fuel (liquid hydrocarbon and liquid hydrogen (LH 2 )), for a portion of the mission. As compared with LH 2 , hydrocarbon fuel has higher density and produces higher thrust-to-weight, but has lower specific impulse. The advantages of hydrocarbon fuel are important early in the ascent trajectory, and its use may be expected to lead to reduced vehicle size and weight. Because LH 2 is also needed for cooling purposes, in the early portion of the trajectory both fuels must be burned simultaneously. Later in the ascent, when vehicle weight is lower, specific impulse is the key parameter, indicating single-fuel LH 2 use
Light and Heavy Tactical Wheeled Vehicle Fuel Consumption Evaluations Using Fuel Efficient Gear Oils (FEGO)

Science.gov (United States)

2016-05-01

UNCLASSIFIED LIGHT AND HEAVY TACTICAL WHEELED VEHICLE FUEL CONSUMPTION EVALUATIONS USING FUEL EFFICIENT GEAR OILS (FEGO) FINAL... HEAVY TACTICAL WHEELED VEHICLE FUEL CONSUMPTION EVALUATIONS USING FUEL EFFICIENT GEAR OILS (FEGO) FINAL REPORT TFLRF No. 477 by Adam C...August 2014 – March 2016 4. TITLE AND SUBTITLE LIGHT AND HEAVY TACTICAL WHEELED VEHICLE FUEL CONSUMPTION EVALUATIONS USING FEUL EFFICIENT GEAR OILS
Emission Control Cost-Effectiveness of Alternative-Fuel Vehicles

OpenAIRE

Wang, Quanlu; Sperling, Daniel; Olmstead, Janis

1993-01-01

Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquified petroleum gas, compressed natural gas, and electricity. Vehicle emission es...
North America and Asia Pacific LNG markets

International Nuclear Information System (INIS)

Pirie, J.D.

1997-01-01

The liquefied natural gas (LNG) export opportunities in the Asia Pacific market were reviewed. Some of the differences that affect a North American LNG projects compared to more typical LNG projects were also outlined. The two main aspects of the LNG market in North America include the establishment of LNG import terminals on the east and southern coasts of the United States and the development of export oriented LNG projects. The Pac-Rim LNG project calls for initial delivery to South Korea of 4.0 MTPA by the end of 2000. A large LNG project has also been proposed for the year 2005 which would use Prudhoe Bay gas. Generally, in North America, there is little use for large scale LNG import projects because of the vast pipeline network that delivers gas reliably and at low cost anywhere in North America. However, LNG remains a good alternative for the Asia Pacific region because of the lack of a pipeline network. Also, Japan, Korea and Taiwan, the three main centers for LNG demand, have no domestic energy supplies and rely on imported energy sources. China is another major market opportunity for LNG. The Pac-Rim LNG project differs from others of its kind in that usually, an LNG project is based on the availability of large reservoirs of natural gas owned by state governments and involves production agreements with multi-national oil and gas companies. This scenario is simply not possible in Canada's deregulated environment. In contrast, the existence of upstream facilities, technical expertise, and low capital costs, hence reduced risks and time to develop an LNG project, gives Canada significant advantages. 3 tabs., 3 figs
LNG Industry in Europe beset by uncertainties

International Nuclear Information System (INIS)

Forbes, A.

2007-01-01

Over the past five years, the liquefied natural gas industry (LNG) has metamorphosed from a specialist niche business into a mainstream source of energy supply, It is currently by far the fastest-growing source of fossil fuel and growth forecasts. However, the industry's future is beset by uncertainty, not least in Europe. Supply is tight, technical skills are hard to come by, and even future demand looks uncertain
Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicles

Science.gov (United States)

primary fuel or to improve the efficiency of conventional vehicle designs. Hybrid Electric Vehicles Icon cost and emissions with a conventional vehicle. Select Fuel/Technology Electric Hybrid Electric Plug-in Hybrid Electric Natural Gas (CNG) Flex Fuel (E85) Biodiesel (B20) Propane (LPG) Next Vehicle Cost
Impact of non-petroleum vehicle fuel economy on GHG mitigation potential

International Nuclear Information System (INIS)

Luk, Jason M; Saville, Bradley A; MacLean, Heather L

2016-01-01

The fuel economy of gasoline vehicles will increase to meet 2025 corporate average fuel economy standards (CAFE). However, dedicated compressed natural gas (CNG) and battery electric vehicles (BEV) already exceed future CAFE fuel economy targets because only 15% of non-petroleum energy use is accounted for when determining compliance. This study aims to inform stakeholders about the potential impact of CAFE on life cycle greenhouse gas (GHG) emissions, should non-petroleum fuel vehicles displace increasingly fuel efficient petroleum vehicles. The well-to-wheel GHG emissions of a set of hypothetical model year 2025 light-duty vehicles are estimated. A reference gasoline vehicle is designed to meet the 2025 fuel economy target within CAFE, and is compared to a set of dedicated CNG vehicles and BEVs with different fuel economy ratings, but all vehicles meet or exceed the fuel economy target due to the policy’s dedicated non-petroleum fuel vehicle incentives. Ownership costs and BEV driving ranges are estimated to provide context, as these can influence automaker and consumer decisions. The results show that CNG vehicles that have lower ownership costs than gasoline vehicles and BEVs with long distance driving ranges can exceed the 2025 CAFE fuel economy target. However, this could lead to lower efficiency CNG vehicles and heavier BEVs that have higher well-to-wheel GHG emissions than gasoline vehicles on a per km basis, even if the non-petroleum energy source is less carbon intensive on an energy equivalent basis. These changes could influence the effectiveness of low carbon fuel standards and are not precluded by the light-duty vehicle GHG emissions standards, which regulate tailpipe but not fuel production emissions. (letter)
LNG projects - nationally and internationally

International Nuclear Information System (INIS)

Graff, Oscar Fr.

2006-01-01

The presentation discusses various aspects of LNG projects nationally and internationally. The emphasis is on the future development of the natural gas markets, the competitiveness and economic requirements of the LNG production and transportation systems and the demands LNG projects will have to competence, technology, products and management
Safety in Liquefied Natural Gas (LNG) Operations

Energy Technology Data Exchange (ETDEWEB)

Buhrow, C. [Technische Univ. Bergakademie, Freiberg (Germany). Lehrstuhl Bergbau/Tiefbau; Niemann-Delius, C.; Okafor, E. [Technische Hochschule Aachen (Germany). Lehrstuhl und Inst. fuer Bergbaukunde 3

2005-07-01

Germany needs an LNG receiving terminal to import LNG and supplement expected future gas supply shortages. Enormous economic benefits also abound if Germany is to install an LNG receiving terminal. Jobs will be created for several hundred people. New tax revenues will be generated for state and local governments and this will further enhance the economic competitiveness of Germany. Additionally, it will provide Germany with a reliable source of clean-burning energy. Any proposed LNG receiving terminal should incorporate safety right from the start. These safety requirements will: ensure that certain public land uses, people, and structures outside the LNG facility boundaries are protected in the event of LNG fire, prevent vapour clouds associated with an LNG spill from reaching a property line that can be built upon, prevent severe burns resulting from thermal radiation, specify requirements for design, construction and use of LNG facilities and other equipments, and promote safe, secure and reliable LNG operations. The German future LNG business will not be complete without the evolution of both local and international standards that can apply to LNG operations. Currently existing European standards also appear inadequate. With an OHSAS 18001 management system integrated with other existing standards we can better control our LNG occupational health and safety risks, and improve performance in the process. Additionally, an OHSAS 18001 System will help future German LNG contractors and operators safeguard their most important assets - their employees. (orig.)
LIQUIFIED NATURAL GAS (LNG) CARRIERS

OpenAIRE

Daniel Posavec; Katarina Simon; Matija Malnar

2010-01-01

Modern liquefied natural gas carriers are double-bottom ships classified according to the type of LNG tank. The tanks are specially designed to store natural gas cooled to -161°C, the boiling point of methane. Since LNG is highly flammable, special care must be taken when designing and operating the ship. The development of LNG carriers has begun in the middle of the twentieth century. LNG carrier storage space has gradually grown to the current maximum of 260000 m3. There are more than 300 L...
Update on the Vancouver Fuel Cell Vehicle Program

International Nuclear Information System (INIS)

Rothwell, B.

2004-01-01

'Full text:' The Vancouver Fuel Cell Vehicle Program (VFCVP) is a $5.8 million initiative designed to test four Ford Focus Fuel Cell Vehicles for three years in the Lower Mainland of British Columbia. The project is the first of its kind in Canada and is led by Fuel Cells Canada (FCC), the Ford Motor Company (Ford), and the Governments of Canada and British Columbia. This presentation will provide program details and an update on activities leading up to currently planned delivery to Vancouver in November 2004. The VFCVP will test the performance, durability and reliability of the Ford fuel cell vehicle cars in real-world conditions and will examine fuelling issues and solutions, the reduction of greenhouse gas emissions and public acceptance of hydrogen fuel cell vehicles. The program will generate data to help evolve the technology and develop international codes and standards E cents Epnd the implementation and adoption of fuel cell technology. (author)
40 CFR 69.51 - Motor vehicle diesel fuel.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Motor vehicle diesel fuel. 69.51... (CONTINUED) SPECIAL EXEMPTIONS FROM REQUIREMENTS OF THE CLEAN AIR ACT Alaska § 69.51 Motor vehicle diesel... motor vehicle diesel fuel standards and dye provisions under 40 CFR 80.520 and associated requirements...

40 CFR 69.52 - Non-motor vehicle diesel fuel.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Non-motor vehicle diesel fuel. 69.52... (CONTINUED) SPECIAL EXEMPTIONS FROM REQUIREMENTS OF THE CLEAN AIR ACT Alaska § 69.52 Non-motor vehicle diesel... NRLM diesel fuel. (5) Exempt NRLM diesel fuel and heating oil must be segregated from motor vehicle...
The LNG Industry - 2010

International Nuclear Information System (INIS)

2011-04-01

In 2010, global energy demand has recovered. Estimates for World Natural Gas consumption show a 7.3% increase compared with 2009 thanks to the economic rally and the cold winter conditions in Western countries. Due to the decline of indigenous productions in mature markets and to the development of new gas markets, international gas flows continued to expand, and total international gas trade increased by 10.9% compared with 2009. In this context, LNG flows recorded the largest growth with a 21% increase in 2010, the operational start-up of new liquefaction capacity in Qatar being the primary reason. By comparison, pipeline trade increased by 7%. This annual report presents: 1 - LNG contracts and trade, 2 - Contracts concluded in 2010, 3 - LNG imports - Sources of imports - Quantities received in 2010, 4 - LNG tankers, 5 - Ships delivered, 6 - Tanker distribution, 7 - Liquefaction plants, 8 - re-gasification plants, 9 - Contracts in force in 2010, 10 - Spot and short term quantities received in 2010, 11 - Sea transportation routes, 12 - Liquefaction plants (table), 13 - re-gasification plants (table), 14 - Delivery date of the LNG tankers
Strategic alliances for the development of fuel cell vehicles

Energy Technology Data Exchange (ETDEWEB)

Maruo, Kanehira [Goeteborg Univ. (Sweden). Section of Science and Technology Studies

1998-12-01

The aim of this paper is to explore and describe the current stage of fuel cell vehicle development in the world. One can write three possible future scenarios - an optimistic, a realistic, and a pessimistic scenario: - The optimistic scenario -- The Daimler/Ballard/Ford alliance continues to develop fuel cell stacks and fuel cell vehicle systems as eagerly as they have been doing in recent years. Daimler(/Chrysler)-Benz continues to present its Necar 4, Necar 5, and so on, as planned, and thus keeps Toyota and Honda under severe pressure. Toyota`s and Honda`s real motivation seems to be not to allow Daimler-Benz to be the first to market. Their investment in fuel cell technology will be very large. At the same time, governments and other stake-holders will quickly and in a timely fashion build up infrastructures. We will then see many fuel cell vehicles by 2004. A paradigm shift in automotive technology will have taken place. - The realistic scenario -- Fuel cell vehicles will reach the same level of development by 2004/2005 as pure electric vehicles were at in 1997/1998. This means that fuel cell vehicles will be produced at the rate of several hundred vehicles per year per manufacturer and cost about $40,000 or more, which is still considerably more expensive than ordinary gasoline cars. These fuel cell vehicles will have a performance similar to today`s advanced electric vehicles, e.g., Toyota`s RAV4/EV and Honda`s EV Plus. To go further from this stage to the mass-production stage strong government incentives will be needed. - The pessimistic scenario -- It turns out that fuel cells are not as pure or efficient as in theory and in laboratory experiments. Prices of gasoline and diesel gas continue to be very low. The Californian 10% ZEV Requirement that has been meant to be valid at least ten years from 2003 through 2012 will be suspended or greatly modified. Daimler-Benz, Toyota, and Honda slow down their fuel cell vehicle development activities. No one is
NREL Fuels and Engines Research: Maximizing Vehicle Efficiency and

Science.gov (United States)

chemistry, conversion, and combustion to the evaluation of advanced fuels in actual engines and vehicles . With fuel chemistry, our scientific discoveries start out small. We use quantum mechanical modeling to explore how fuels with varying chemistry interact with engine and vehicle design. At our Fuel Combustion
LNG - emergency control

Energy Technology Data Exchange (ETDEWEB)

Berardinelli, Ricardo Porto; Correa, Kleber Macedo; Moura Filho, Nelson Barboza de; Fernandez, Carlos Antonio [TRANSPETRO, Rio de Janeiro, RJ (Brazil); Matos, Jose Eduardo Nogueira de [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2009-07-01

The operation of liquefied natural gas (LNG) is pioneering within the PETROBRAS System. PETROBRAS Transporte - TRANSPETRO is going to operate two flexible LNG terminals, located in Ceara and Rio de Janeiro. In accordance with the Corporate Health, Safety and Environmental (HSE) Directive - Training, Education and Awareness, PETROBRAS Transporte S.A. - TRANSPETRO has prepared an action plan with the objective of ensuring the operational safety of the undertaking. Among other actions a training program for the emergency control of LNG will be inserted into the timetable. The above mentioned training program was held over a period of 20 hours, and was divided between theory and practice. In the theoretical part, the characteristics of the product, the history of accidents and the emergency response procedures were covered. In the practical part, 3000 gallons of LNG were utilized where the behavior of the product could be confirmed following a confined leak, thereby verifying the efficacy of the emergency control resources. The teaching process of the course was developed in the company through the preparation of specific procedures, emergency plans and the formation of internal instructors. (author)
Effects of ambient conditions on fuel cell vehicle performance

Science.gov (United States)

Haraldsson, K.; Alvfors, P.

Ambient conditions have considerable impact on the performance of fuel cell hybrid vehicles. Here, the vehicle fuel consumption, the air compressor power demand, the water management system and the heat loads of a fuel cell hybrid sport utility vehicle (SUV) were studied. The simulation results show that the vehicle fuel consumption increases with 10% when the altitude increases from 0 m up to 3000 m to 4.1 L gasoline equivalents/100 km over the New European Drive Cycle (NEDC). The increase is 19% on the more power demanding highway US06 cycle. The air compressor is the major contributor to this fuel consumption increase. Its load-following strategy makes its power demand increase with increasing altitude. Almost 40% of the net power output of the fuel cell system is consumed by the air compressor at the altitude of 3000 m with this load-following strategy and is thus more apparent in the high-power US06 cycle. Changes in ambient air temperature and relative humidity effect on the fuel cell system performance in terms of the water management rather in vehicle fuel consumption. Ambient air temperature and relative humidity have some impact on the vehicle performance mostly seen in the heat and water management of the fuel cell system. While the heat loads of the fuel cell system components vary significantly with increasing ambient temperature, the relative humidity did not have a great impact on the water balance. Overall, dimensioning the compressor and other system components to meet the fuel cell system requirements at the minimum and maximum expected ambient temperatures, in this case 5 and 40 °C, and high altitude, while simultaneously choosing a correct control strategy are important parameters for efficient vehicle power train management.
Future forecast for life-cycle greenhouse gas emissions of LNG and city gas 13A

International Nuclear Information System (INIS)

Okamura, Tomohito; Furukawa, Michinobu; Ishitani, Hisashi

2007-01-01

The objective of this paper is to analyze the most up-to-date data available on total greenhouse-gas emissions of a LNG fuel supply chain and life-cycle of city gas 13A based on surveys of the LNG projects delivering to Japan, which should provide useful basic-data for conducting life-cycle analyses of other product systems as well as future alternative energy systems, because of highly reliable data qualified in terms of its source and representativeness. In addition, the life-cycle greenhouse-gas emissions of LNG and city-gas 13A in 2010 were also predicted, taking into account not only the improvement of technologies, but also the change of composition of LNG projects. As a result of this analysis, the total amount of greenhouse-gas emissions of the whole city-gas 13A chain at present was calculated to be 61.91 g-CO 2 /MJ, and the life-cycle greenhouse-gas emissions of LNG and city-gas 13A in 2010 could be expected to decrease by about 1.1% of the current emissions
Panel discussion: LNG's future in Asia

International Nuclear Information System (INIS)

Ohashi, Tadahiko

1992-01-01

The panelists convened to: (1) identify and evaluate the role which LNG is likely to play in the changing energy scene; (2) to examine the future supply and demand structure of the LNG trade; (3) to discover the key obstacles to continued growth in LNG trade; and (4) to find solutions to these problems. The panelists identified and outlined growing opportunities for LNG utilization in Asia during the next two decades. They shared the opinion that the structure of the supply and demand balance for LNG in Asia will shift during the next decade, providing considerable room for new projects. The key obstacles to continued growth in LNG trade are the lack of: long-distance transmission networks and an efficient competitive market pricing mechanism for LNG in the Asian region. The major importers in the region are keen on developing a range of new long-term supply alternatives, not simply within the Asia-Pacific region, but also from a wider perspective. These alternatives include: financing the expansion of production from existing facilities, development of new fields, and construction of long-distance pipelines
Global LNG - characteristics, clients and contracts

International Nuclear Information System (INIS)

Bauquis, P.R.

1997-01-01

Total's liquefied natural gas (LNG) holdings were described. Other topics discussed included an overview of gas consumption and internationally traded gas in 1995, a primer on the history of LNG, Japan's average import prices in 1996, Europe's border gas prices and consumption in 1995, Canada/US regional price differences in 1995 and 1996, and world gas markets and prices in 1996. The projected LNG supply and demand in Europe and Asia , especially in Japan, China and India, was also discussed. General concepts of LNG pricing, the general structure of a gas sales contract, and the different categories of LNG contracts were also reviewed. 24 figs
The DOE/NREL Next Generation Natural Gas Vehicle Program - An Overview

International Nuclear Information System (INIS)

Kevin Walkowicz; Denny Stephens; Kevin Stork

2001-01-01

This paper summarizes the Next Generation Natural Gas Vehicle (NG-NGV) Program that is led by the U.S. Department Of Energy's (DOE's) Office of Heavy Vehicle Technologies (OHVT) through the National Renewable Energy Laboratory (NREL). The goal of this program is to develop and implement one Class 3-6 compressed natural gas (CNG) prototype vehicle and one Class 7-8 liquefied natural gas (LNG) prototype vehicle in the 2004 to 2007 timeframe. OHVT intends for these vehicles to have 0.5 g/bhp-hr or lower emissions of oxides of nitrogen (NOx) by 2004 and 0.2 g/bhp-hr or lower NOx by 2007. These vehicles will also have particulate matter (PM) emissions of 0.01 g/bhp-hr or lower by 2004. In addition to ambitious emissions goals, these vehicles will target life-cycle economics that are compatible with their conventionally fueled counterparts
Alternative Fuels Data Center: Yellowstone Park Recycles Vehicle Batteries

Science.gov (United States)

for Solar Power Yellowstone Park Recycles Vehicle Batteries for Solar Power to someone by E -mail Share Alternative Fuels Data Center: Yellowstone Park Recycles Vehicle Batteries for Solar Power on Facebook Tweet about Alternative Fuels Data Center: Yellowstone Park Recycles Vehicle Batteries
The Malaysia LNG experience

International Nuclear Information System (INIS)

Muhammed, M.

1991-01-01

This paper summarizes the nature of the LNG trade, the essential components and characteristics of an LNG project, and relates the Malaysia LNG experience to project realization with some emphasis on the financial aspects of the project. Twelve offshore lending institutions were involved in the total project loop providing U.S. dollar equivalents of 4.0 billions with interest rates ranging from 5% to 8%. The total project was completed on schedule and within budget except for the ships which got caught in the political development of the Malaysian petroleum industry at that time
Sustainable vehicle fuels - Do they exist?

Energy Technology Data Exchange (ETDEWEB)

Boerjesson, Paal; Ericsson, Karin; Di Lucia, Lorenzo; Nilsson, Lars J.; Aahman, Max

2009-03-15

Our aim with this report is to discuss vehicle fuels from a wide perspective of sustainability. Biofuels and electricity are analyzed and compared to fossil vehicle fuels. Our goal is to try to point out the circumstances under which vehicle fuels can be reasonably perceived as sustainable, and which systems we should develop and which we should avoid. The all-embracing conclusion of this study is that one can not establish how sustainable fuels will develop in the future without simultaneously taking into consideration both scale and pace of growth. Today's biofuels produced in Sweden are sustainable, given the present production volume, and promote further development of new fuel systems. However, in the case of increased production volumes, exact requirements should be established for the energy- and climate efficiency of the entire fuel chain (from cultivation to tank). High priority should be given to the development of fuel-efficient cars. In this field hybrid electric technology and electric cars will grow in importance. Any long-term strategy for biofuels should include investments in technology for both thermal gasification and biological conversion methods of lignocellulose, since these are complementing as much as competing technologies, both increasing the flexibility as well as decreasing the risk of conflicts. Biogas from waste products has great environmental advantages and the sector can be expanded with only small risks of conflicts. Certification (if correctly formulated) is an important and necessary tool on the way towards more sustainable vehicle fuels and increased production volumes, but certification systems should not be overrated since they can not cover all sustainability aspects. Socio-economic aspects such as working conditions, local rural development etc. must be dealt with through general measures such as national laws, distribution policies, programs and plans, all of which should be supported by international agreements and
77 FR 73627 - 2012 LNG Export Study

Science.gov (United States)

2012-12-11

... DEPARTMENT OF ENERGY 2012 LNG Export Study AGENCY: Office of Fossil Energy, Department of Energy. ACTION: Notice of availability of 2012 LNG Export Study and request for comments. Freeport LNG Expansion, L.P. [FE Docket No. 10-161-LNG] and FLNG Liquefaction, LLC. Lake Charles Exports, LLC.... [FE Docket...
Alternative Fuels Data Center: Signage for Plug-In Electric Vehicle

Science.gov (United States)

Send a link to Alternative Fuels Data Center: Signage for Plug-In Electric Vehicle Charging Stations to someone by E-mail Share Alternative Fuels Data Center: Signage for Plug-In Electric Vehicle Charging Stations on Facebook Tweet about Alternative Fuels Data Center: Signage for Plug-In Electric Vehicle
Motor vehicle fuel economy, the forgotten HC control stragegy?

Energy Technology Data Exchange (ETDEWEB)

Deluchi, M.; Wang, Quanlu; Greene, D.L.

1992-06-01

Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.
Dynamic behavior of gasoline fuel cell electric vehicles

Science.gov (United States)

Mitchell, William; Bowers, Brian J.; Garnier, Christophe; Boudjemaa, Fabien

As we begin the 21st century, society is continuing efforts towards finding clean power sources and alternative forms of energy. In the automotive sector, reduction of pollutants and greenhouse gas emissions from the power plant is one of the main objectives of car manufacturers and innovative technologies are under active consideration to achieve this goal. One technology that has been proposed and vigorously pursued in the past decade is the proton exchange membrane (PEM) fuel cell, an electrochemical device that reacts hydrogen with oxygen to produce water, electricity and heat. Since today there is no existing extensive hydrogen infrastructure and no commercially viable hydrogen storage technology for vehicles, there is a continuing debate as to how the hydrogen for these advanced vehicles will be supplied. In order to circumvent the above issues, power systems based on PEM fuel cells can employ an on-board fuel processor that has the ability to convert conventional fuels such as gasoline into hydrogen for the fuel cell. This option could thereby remove the fuel infrastructure and storage issues. However, for these fuel processor/fuel cell vehicles to be commercially successful, issues such as start time and transient response must be addressed. This paper discusses the role of transient response of the fuel processor power plant and how it relates to the battery sizing for a gasoline fuel cell vehicle. In addition, results of fuel processor testing from a current Renault/Nuvera Fuel Cells project are presented to show the progress in transient performance.
Prospects for the application of fuel cells in electric vehicles

Energy Technology Data Exchange (ETDEWEB)

Adcock, P L; Newbold, A [Loughborough Univ. of Technology (United Kingdom). Dept. of Transport Technology; Barton, R T; Dudfield, C D; Mitchell, P J; Naylor, P [Loughborough Univ. of Technology (United Kingdom). Dept. of Chemistry

1992-01-01

For a hybrid vehicle the use pattern has large effect on the vehicle design. If the vehicle is to be used extensively on the motorway then a continuous high power is required. For the case of a fuel cell battery hybrid vehicle this would require a large fuel cell (> 30 kW) to meet the sustained high power demand. The current high materials and fabrication cost of most fuel cells prohibits the commercial development of such a system. Consequently if fuel cell vehicles are to enter a 'clean car' market, earlier rather than later, alternative configurations must be sought and compromises in terms of performance are inevitable. (orig.).
Arctic Islands LNG

Energy Technology Data Exchange (ETDEWEB)

Hindle, W.

1977-01-01

Trans-Canada Pipe Lines Ltd. made a feasibility study of transporting LNG from the High Arctic Islands to a St. Lawrence River Terminal by means of a specially designed and built 125,000 cu m or 165,000 cu m icebreaking LNG tanker. Studies were made of the climatology and of ice conditions, using available statistical data as well as direct surveys in 1974, 1975, and 1976. For on-schedule and unimpeded (unescorted) passage of the LNG carriers at all times of the year, special navigation and communications systems can be made available. Available icebreaking experience, charting for the proposed tanker routes, and tide tables for the Canadian Arctic were surveyed. Preliminary design of a proposed Arctic LNG icebreaker tanker, including containment system, reliquefaction of boiloff, speed, power, number of trips for 345 day/yr operation, and liquefaction and regasification facilities are discussed. The use of a minimum of three Arctic Class 10 ships would enable delivery of volumes of natural gas averaging 11.3 million cu m/day over a period of a year to Canadian markets. The concept appears to be technically feasible with existing basic technology.
Natural gas for ship propulsion in Denmark - Possibilities for using LNG and CNG on ferry and cargo routes

Energy Technology Data Exchange (ETDEWEB)

Stuer-Lauridsen, F.; Nielsen, Jesper B. (LITEHAUZ, Copenhagen (Denmark)); Odgaard, T.; Birkeland, M. (IncentivePartners, Birkeroed (Denmark)); Winter Graugaard, C.; Blikom, L.P. (DNV, Copenhagen (Denmark)); Muro-Sun, N.; Andersen, Morten; OEvlisen, F. (Ramboell Oil and Gas, Esbjerg (Denmark))

2010-07-01

The project's main task was to review logistical, technical and economic feasibility for using Liquefied Natural Gas (LNG) and Compressed Natural Gas (CNG) as fuel for ship propulsion and the supply of LNG or CNG to Danish ports from existing natural gas lines, trucks or by ship. The following key findings are related to the use of natural gas as fuel for ships in Denmark: Natural gas as propulsion fuel in ships: 1) Advantages: Provide solution to present air emission challenges 2) Barriers: Capital investments large 3) Synergies: Developments in Norway and Baltic Sea area 4) Economy: Positive case for operation for large consumers 5) Future: Develop bunkering options for short sea shipping LNG: 6) Propulsion technology in ships is mature and proven 7) Distribution network not yet developed for use in ships 8) Safety concerns are demanding but manageable 9) Can enter existing bunkering value chain CNG: 10) Well developed for land based transport, not yet for shipping 11) Distribution network for natural gas exists in Denmark 12) Safety concerns are demanding but manageable 13) No seaborne CNG value chains in operation An immediate focus on the ferry sector in Denmark will reap benefits on a relatively short time scale. For the short sea shipping sector away to promote the conversion to natural gas is to support the development of storage and bunkering facilities in main ports. Given the general expectations in the shipping community LNG will presumably be the de facto choice at least for the 5-10 years ahead and the demand for facilities and bunkers will be for LNG. (LN)

The LNG Industry in 2006

International Nuclear Information System (INIS)

Anon.

2007-01-01

Estimates for the marketed production of natural gas in 2006 show a rise of about 3% over 2005. The share of LNG in the gas trade accounts for 23% of the total. In 2006, the international trade in liquid form accounted for 348.4 10 6 m 3 or almost 159 10 6 t. It rose by 38.4 10 6 m 3 , or 12.4%, the highest growth rate ever recorded over the last decade. As to imports: - Japan remained by far the world's largest LNG importer with 136 10 6 m 3 , or 39% of all imports, followed by Korea with 55.3 10 6 m 3 (15.9%) and Spain with 41.6 10 6 m 3 (12.0%), markedly higher than the U.S.A. ranking fourth with 26 10 6 m 3 (7.5%). Seventeen countries were involved in LNG imports with the addition of China and Mexico in 2006. - The growth rate of European imports remained stable at 21%, above the global growth rate of 12.4%, resulting in a market share for Europe of 27.4% and demonstrating the dynamism of this region in the LNG trade. With a 12% market share in worldwide trade, Spain maintained its position as Europe's largest LNG market. - After substantial increases during the early part of this decade, the US market suffered most from the shortage in LNG production and price arbitration prompted some shippers to divert spot LNG away from the US market. Imports for the Americas as a whole still decreased by 3.2% and their global market share fell to 8.5%. - The Asian market kept on growing steadily by 11.4% with imports to the region rising from 200.6 10 6 m 3 to 223.4 10 6 m 3 or an increase of 22.8 10 6 m 3 , mainly due to the continued rise of Indian imports with a 3.9% market share, and the emergence of China on the LNG scene. Japanese imports steadily rose to 136 10 6 m 3 . Korea also enjoyed a significant growth by 13.5% to 55.3 10 6 m 3 while Taiwan's imports grew by 8.5% to 17 10 6 m 3 . As to sources of imports: Indonesia lost its leading position and Qatar became the world's largest LNG producer with 15.5% of all exports. Indonesia ranked second with 13.9%, Malaysia
Effects of High Octane Ethanol Blends on Four Legacy Flex-Fuel Vehicles, and a Turbocharged GDI Vehicle

Energy Technology Data Exchange (ETDEWEB)

Thomas, John F [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); West, Brian H [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Huff, Shean P [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-03-01

The U.S. Department of Energy (DOE) is supporting engine and vehicle research to investigate the potential of high-octane fuels to improve fuel economy. Ethanol has very high research octane number (RON) and heat of vaporization (HoV), properties that make it an excellent spark ignition engine fuel. The prospects of increasing both the ethanol content and the octane number of the gasoline pool has the potential to enable improved fuel economy in future vehicles with downsized, downsped engines. This report describes a small study to explore the potential performance benefits of high octane ethanol blends in the legacy fleet. There are over 17 million flex-fuel vehicles (FFVs) on the road today in the United States, vehicles capable of using any fuel from E0 to E85. If a future high-octane blend for dedicated vehicles is on the horizon, the nation is faced with the classic chicken-and-egg dilemma. If today’s FFVs can see a performance advantage with a high octane ethanol blend such as E25 or E30, then perhaps consumer demand for this fuel can serve as a bridge to future dedicated vehicles. Experiments were performed with four FFVs using a 10% ethanol fuel (E10) with 88 pump octane, and a market gasoline blended with ethanol to make a 30% by volume ethanol fuel (E30) with 94 pump octane. The research octane numbers were 92.4 for the E10 fuel and 100.7 for the E30 fuel. Two vehicles had gasoline direct injected (GDI) engines, and two featured port fuel injection (PFI). Significant wide open throttle (WOT) performance improvements were measured for three of the four FFVs, with one vehicle showing no change. Additionally, a conventional (non-FFV) vehicle with a small turbocharged direct-injected engine was tested with a regular grade of gasoline with no ethanol (E0) and a splash blend of this same fuel with 15% ethanol by volume (E15). RON was increased from 90.7 for the E0 to 97.8 for the E15 blend. Significant wide open throttle and thermal efficiency performance
46 CFR 154.703 - Methane (LNG).

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Methane (LNG). 154.703 Section 154.703 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR... and Temperature Control § 154.703 Methane (LNG). Unless a cargo tank carrying methane (LNG) can...
Technical evaluation and assessment of CNG/LPG bi-fuel and flex-fuel vehicle viability

Science.gov (United States)

Sinor, J. E.

1994-05-01

This report compares vehicles using compressed natural gas (CNG), liquefied petroleum gas (LPG), and combinations of the two in bi-fuel or flex-fuel configurations. Evidence shows that environmental and energy advantages can be gained by replacing two-fuel CNG/gasoline vehicles with two-fuel or flex-fuel systems to be economically competitive, it is necessary to develop a universal CNG/LPG pressure-regulator-injector and engine control module to switch from one tank to the other. For flex-fuel CNG/LPG designs, appropriate composition sensors, refueling pumps, fuel tanks, and vaporizers are necessary.
Direct hydrogen fuel cell systems for hybrid vehicles

Science.gov (United States)

Ahluwalia, Rajesh K.; Wang, X.

Hybridizing a fuel cell system with an energy storage system offers an opportunity to improve the fuel economy of the vehicle through regenerative braking and possibly to increase the specific power and decrease the cost of the combined energy conversion and storage systems. Even in a hybrid configuration it is advantageous to operate the fuel cell system in a load-following mode and use the power from the energy storage system when the fuel cell alone cannot meet the power demand. This paper discusses an approach for designing load-following fuel cell systems for hybrid vehicles and illustrates it by applying it to pressurized, direct hydrogen, polymer-electrolyte fuel cell (PEFC) systems for a mid-size family sedan. The vehicle level requirements relative to traction power, response time, start-up time and energy conversion efficiency are used to select the important parameters for the PEFC stack, air management system, heat rejection system and the water management system.
How the Norwegian Maritime Sector can succeed in internationalizing LNG-technology to Southeast Asia: A Case Study of Rolls-Royce Marine

OpenAIRE

Tveten, Rolf Erik; Løset, Gaute Dag

2012-01-01

The future potential of LNG as a bunker fuel in the Southeast Asian market is huge, although it is still immature. An emerging market for LNG-propulsion in the region creates a business opportunity for Norwegian companies delivering relevant products and services. This is a summary of the strategy that will yield the highest return on a foreign market entry with focus on export of LNG-technology in the Southeast Asian region. This thesis has assessed the gas producing and consuming countries,...
Fuel cells show promise as vehicle power source

International Nuclear Information System (INIS)

Anon.

1980-01-01

Fuel-cell-powered vehicles appear to offer great promise for energy-saving, high-efficiency transportation. Fuel cells are both highly efficient (50% thermal efficiency has been demonstrated by some) and non-polluting (water being the main by-product). Dramatic improvements in performance have occurred recently due to aerospace and utility RandD efforts. The primary vehicle considered at workshops of laboratory and industrial investigators was a fuel cell/battery hybrid, in which fuel cells are paralleled by batteries. Fuel cells are used for cruising power and battery recharge, while batteries supply transient power for acceleration and starting
Study questions environmental impact of fuel-cell vehicles

Science.gov (United States)

Stafford, Ned

2015-09-01

Fuel-cell electric vehicles are seen by many as an environmentally friendly technology that can reduce greenhousegas emissions by producing no harmful emissions. But a new study has found that overall a fuel cell electric vehicle has about the same negative environmental impact as a luxury sports car.
Effects of alternative-fuel vehicles on air quality in Ontario, Canada

International Nuclear Information System (INIS)

Kantor, I.; Fowler, M.; Hajimiragha, A.; Canizares, C.; Elkamel, A.

2009-01-01

The economies of the developed world are increasingly including green technologies and processes that consider social, environmental and economic consequences. Hybrid electric vehicles and other fuel-efficient vehicle types can supply consumers with vehicles that decrease their ecological footprint and reduce the cost of fuel. However, one of the societal concerns often overlooked is the impact of alternative-fuel vehicle usage on the air quality in the urban environment. This paper presented a study that assessed the impact on air quality stemming from the operation of alternative fuel vehicles in urban environments. The study specifically focused on the province-wide emissions in Ontario and urban air pollution in the city of Toronto. The paper considered the life-cycle impacts of using alternative fuels for transportation purposes in terms of six major stressors for climate change, acidification and urban air quality. The two types of vehicles that were studied were plug-in hybrid electric vehicles (PHEVs) and fuel cell vehicles. Modeling of the penetration rates for both types of vehicles was completed based on the maximum capacity of the electrical grid including planned improvements. The scope of the study and discussion of health effects was first presented followed by data gathering and usage, methodology, results of supportable penetration and vehicle growth, and pollution abatement results. It was concluded that fuel cell vehicles have an advantage over, or near-equality with, PHEVs in almost every aspect of their emissions. 13 refs., 2 tabs., 10 figs
National blueprint for the deployment of liquefied natural gas as marine fuel

International Nuclear Information System (INIS)

2016-01-01

Based on a consultation of professional bodies, this blueprint expresses the strong commitment of the French State with economic actors towards an energy transition on the long term, and more particularly concerns the development of LNG (liquefied natural gas) as marine fuel. This objective complies with national and European environmental objectives for the reduction of greenhouse emissions and for a better air quality. This blueprint notably develops two European directives which addresses the sulphur content of marine fuels, and the deployment of an infrastructure for alternative fuels. In its first part, this document states the strong political support to the development of LNG: environmental objectives, existing financial levers for a progressive evolution towards LNG, adaptation of the regulatory framework for a sustainable emergence of a LNG sector, implementation of specific trainings of sea-based and ground-based personnel for the handling of LNG. It sketches the development of LNG for each French coastline (Manche-North Sea, Atlantic, Mediterranean Sea) by analysing the potential demand, and by presenting current projects. Some specific issues related to LNG development are then addressed and discussed: creation of global LNG sectors, inclusion of projects within a trans-national approach, taking of the LNG multimodal reality into account. A set of actions is finally defined: definition of a national framework, stronger support of actors in the search for relevant financing solutions, emergence of harmonized regulatory conditions, implementation of relevant training for LNG handling, support to the implementation of projects which will enable the emergence of a LNG sector for fuel supply in France
Legacy Vehicle Fuel System Testing with Intermediate Ethanol Blends

Energy Technology Data Exchange (ETDEWEB)

Davis, G. W.; Hoff, C. J.; Borton, Z.; Ratcliff, M. A.

2012-03-01

The effects of E10 and E17 on legacy fuel system components from three common mid-1990s vintage vehicle models (Ford, GM, and Toyota) were studied. The fuel systems comprised a fuel sending unit with pump, a fuel rail and integrated pressure regulator, and the fuel injectors. The fuel system components were characterized and then installed and tested in sample aging test rigs to simulate the exposure and operation of the fuel system components in an operating vehicle. The fuel injectors were cycled with varying pulse widths during pump operation. Operational performance, such as fuel flow and pressure, was monitored during the aging tests. Both of the Toyota fuel pumps demonstrated some degradation in performance during testing. Six injectors were tested in each aging rig. The Ford and GM injectors showed little change over the aging tests. Overall, based on the results of both the fuel pump testing and the fuel injector testing, no major failures were observed that could be attributed to E17 exposure. The unknown fuel component histories add a large uncertainty to the aging tests. Acquiring fuel system components from operational legacy vehicles would reduce the uncertainty.
40 CFR 80.531 - How are motor vehicle diesel fuel credits generated?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false How are motor vehicle diesel fuel... (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel... are motor vehicle diesel fuel credits generated? (a) Generation of credits from June 1, 2006 through...
Natural gas and CO2 price variation: impact on the relative cost-efficiency of LNG and pipelines.

Science.gov (United States)

Ulvestad, Marte; Overland, Indra

2012-06-01

THIS ARTICLE DEVELOPS A FORMAL MODEL FOR COMPARING THE COST STRUCTURE OF THE TWO MAIN TRANSPORT OPTIONS FOR NATURAL GAS: liquefied natural gas (LNG) and pipelines. In particular, it evaluates how variations in the prices of natural gas and greenhouse gas emissions affect the relative cost-efficiency of these two options. Natural gas is often promoted as the most environmentally friendly of all fossil fuels, and LNG as a modern and efficient way of transporting it. Some research has been carried out into the local environmental impact of LNG facilities, but almost none into aspects related to climate change. This paper concludes that at current price levels for natural gas and CO 2 emissions the distance from field to consumer and the volume of natural gas transported are the main determinants of transport costs. The pricing of natural gas and greenhouse emissions influence the relative cost-efficiency of LNG and pipeline transport, but only to a limited degree at current price levels. Because more energy is required for the LNG process (especially for fuelling the liquefaction process) than for pipelines at distances below 9100 km, LNG is more exposed to variability in the price of natural gas and greenhouse gas emissions up to this distance. If the prices of natural gas and/or greenhouse gas emission rise dramatically in the future, this will affect the choice between pipelines and LNG. Such a price increase will be favourable for pipelines relative to LNG.
Estimating Vehicle Fuel Consumption and Emissions Using GPS Big Data.

Science.gov (United States)

Kan, Zihan; Tang, Luliang; Kwan, Mei-Po; Zhang, Xia

2018-03-21

The energy consumption and emissions from vehicles adversely affect human health and urban sustainability. Analysis of GPS big data collected from vehicles can provide useful insights about the quantity and distribution of such energy consumption and emissions. Previous studies, which estimated fuel consumption/emissions from traffic based on GPS sampled data, have not sufficiently considered vehicle activities and may have led to erroneous estimations. By adopting the analytical construct of the space-time path in time geography, this study proposes methods that more accurately estimate and visualize vehicle energy consumption/emissions based on analysis of vehicles' mobile activities ( MA ) and stationary activities ( SA ). First, we build space-time paths of individual vehicles, extract moving parameters, and identify MA and SA from each space-time path segment (STPS). Then we present an N-Dimensional framework for estimating and visualizing fuel consumption/emissions. For each STPS, fuel consumption, hot emissions, and cold start emissions are estimated based on activity type, i.e., MA , SA with engine-on and SA with engine-off. In the case study, fuel consumption and emissions of a single vehicle and a road network are estimated and visualized with GPS data. The estimation accuracy of the proposed approach is 88.6%. We also analyze the types of activities that produced fuel consumption on each road segment to explore the patterns and mechanisms of fuel consumption in the study area. The results not only show the effectiveness of the proposed approaches in estimating fuel consumption/emissions but also indicate their advantages for uncovering the relationships between fuel consumption and vehicles' activities in road networks.
The importance of vehicle costs, fuel prices, and fuel efficiency to HEV market success.

Energy Technology Data Exchange (ETDEWEB)

Santini, D. J.; Patterson, P. D.; Vyas, A. D.

1999-12-08

Toyota's introduction of a hybrid electric vehicle (HEV) named ''Prius'' in Japan and Honda's proposed introduction of an HEV in the United States have generated considerable interest in the long-term viability of such fuel-efficient vehicles. A performance and cost projection model developed entirely at Argonne National Laboratory (ANL) is used here to estimate costs. ANL staff developed fuel economy estimates by extending conventional vehicle (CV) modeling done primarily under the National Cooperative Highway Research Program. Together, these estimates are employed to analyze dollar costs vs. benefits of two of many possible HEV technologies. We project incremental costs and fuel savings for a Prius-type low-performance hybrid (14.3 seconds zero to 60 mph acceleration, 260 time) and a higher-performance ''mild'' hybrid vehicle, or MHV (11 seconds 260 time). Each HEV is compared to a U.S. Toyota Corolla with automatic transmission (11 seconds 260 time). The base incremental retail price range, projected a decade hence, is $3,200-$3,750, before considering battery replacement cost. Historical data are analyzed to evaluate the effect of fuel price on consumer preferences for vehicle fuel economy, performance, and size. The relationship between fuel price, the level of change in fuel price, and consumer attitude toward higher fuel efficiency is also evaluated. A recent survey on the value of higher fuel efficiency is presented and U.S. commercial viability of the hybrids is evaluated using discount rates of 2090 and 870. Our analysis, with our current HEV cost estimates and current fuel savings estimates, implies that the U.S. market for such HEVS would be quite limited.
How hybrid-electric vehicles are different from conventional vehicles: the effect of weight and power on fuel consumption

International Nuclear Information System (INIS)

Reynolds, C; Kandlikar, M

2007-01-01

An increasingly diverse set of hybrid-electric vehicles (HEVs) is now available in North America. The recent generation of HEVs have higher fuel consumption, are heavier, and are significantly more powerful than the first generation of HEVs. We compare HEVs for sale in the United States in 2007 to equivalent conventional vehicles and determine how vehicle weight and system power affects fuel consumption within each vehicle set. We find that heavier and more powerful hybrid-electric vehicles are eroding the fuel consumption benefit of this technology. Nonetheless, the weight penalty for fuel consumption in HEVs is significantly lower than in equivalent conventional internal combustion engine vehicles (ICEVs). A 100 kg change in vehicle weight increases fuel consumption by 0.7 l/100 km in ICEVs compared with 0.4 l/100 km in HEVs. When the HEVs are compared with their ICEV counterparts in an equivalence model that differentiates between cars and sports-utility vehicles, the average fuel consumption benefit was 2.7 l/100 km. This analysis further reveals that a HEV which is 100 kg heavier than an identical ICEV would have a fuel consumption penalty of 0.15 l/100 km. Likewise, an increase in the HEV's power by 10 kW results in a fuel consumption penalty of 0.27 l/100 km
LNG's renaissance in the U.S. -- why now?

International Nuclear Information System (INIS)

Moore, J.

2000-01-01

The present state and future prospects for the U.S. liquefied natural gas industry are reviewed in light of expanding opportunities for LNG export worldwide. An update on new tanker ships to transport LNG by both exporters and importers and on developments at US LNG facilities at Everett, MA, Cove Point, MD, Elba Island, GA, and at Lake Charles, LA, is provided, along with an assessment of East Coast supply sources and demand forecast. The prediction is that worldwide supply/demand for LNG will tighten, that US prices will be strong enough to support LNG, that proposed expansion of LNG liquefaction facilities in the Atlantic Basin will fill US import facilities, and that East Coast demand growth will absorb growth in LNG imports
Financial structure of Korea Gas Corporation's LNG projects

International Nuclear Information System (INIS)

Jeongsoo Ko

1991-01-01

When an Indonesian LNG tanker arrived in Korea for the first time in October 1986, Korea became the seventh LNG-consuming nation in the world. The imported LNG has contributed greatly to solving pollution problems and ensuring a stable supply of energy to Korea through the diversification of energy sources. So far, the LNG supply has been confined to the Metropolitan area. The Korea Gas Corporation now plans to expand the LNG supply to cover the entire nation. This paper introduces the experience and future plan of Korea's LNG projects with a special reference to their financial structure
Evaluation of fuel cell hybrid electric light commercial vehicle

Energy Technology Data Exchange (ETDEWEB)

Thomas, G.M.

2002-07-01

This report summarised the results of tests both in the laboratory and in operation on the roads in London carried out to determine the performance of the Zetek Fuel Cell Vehicle operated by Westminster County Council. Details are given of the vehicle's data logging system, and measurement of its acceleration and power, driveability, vehicle range, and the energy efficiency of the fuel cell, and its environmental performance. The frequent shutdowns of the fuel cell system and the problems with the DC/DC converter are discussed.
Alternative Fuels Data Center: How Do Diesel Vehicles Work Using Biodiesel?

Science.gov (United States)

Diesel Vehicles Work Using Biodiesel? to someone by E-mail Share Alternative Fuels Data Center: How Do Diesel Vehicles Work Using Biodiesel? on Facebook Tweet about Alternative Fuels Data Center: How Do Diesel Vehicles Work Using Biodiesel? on Twitter Bookmark Alternative Fuels Data Center: How Do

Effect of Intake Air Filter Condition on Vehicle Fuel Economy

Energy Technology Data Exchange (ETDEWEB)

Norman, Kevin M [ORNL; Huff, Shean P [ORNL; West, Brian H [ORNL

2009-02-01

The U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy and the U.S. Environmental Protection Agency (EPA) jointly maintain a fuel economy website (www.fueleconomy.gov), which helps fulfill their responsibility under the Energy Policy Act of 1992 to provide accurate fuel economy information [in miles per gallon (mpg)] to consumers. The site provides information on EPA fuel economy ratings for passenger cars and light trucks from 1985 to the present and other relevant information related to energy use such as alternative fuels and driving and vehicle maintenance tips. In recent years, fluctuations in the price of crude oil and corresponding fluctuations in the price of gasoline and diesel fuels have renewed interest in vehicle fuel economy in the United States. (User sessions on the fuel economy website exceeded 20 million in 2008 compared to less than 5 million in 2004 and less than 1 million in 2001.) As a result of this renewed interest and the age of some of the references cited in the tips section of the website, DOE authorized the Oak Ridge National Laboratory (ORNL) Fuels, Engines, and Emissions Research Center (FEERC) to initiate studies to validate and improve these tips. This report documents a study aimed specifically at the effect of engine air filter condition on fuel economy. The goal of this study was to explore the effects of a clogged air filter on the fuel economy of vehicles operating over prescribed test cycles. Three newer vehicles (a 2007 Buick Lucerne, a 2006 Dodge Charger, and a 2003 Toyota Camry) and an older carbureted vehicle were tested. Results show that clogging the air filter has no significant effect on the fuel economy of the newer vehicles (all fuel injected with closed-loop control and one equipped with MDS). The engine control systems were able to maintain the desired AFR regardless of intake restrictions, and therefore fuel consumption was not increased. The carbureted engine did show a decrease in
Fuel-Efficient Road Vehicle Non-Engine Components

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The need to address global energy issues, i.e. energy security and climate change, is more urgent than ever. Road vehicles dominate global oil consumption and are one of the fastest growing energy end-uses. This paper studies policies and measures to improve on-road fuel efficiency of vehicles by focusing on energy efficiency of automobile components not generally considered in official fuel efficiency test, namely tyres, cooling technologies and lightings. In this paper, current policies and industry activities on these components are reviewed, fuel saving potential by the components analysed and possible policies to realise the potential recommended.
Increasing the Fuel Economy and Safety of New Light-DutyVehicles

Energy Technology Data Exchange (ETDEWEB)

Wenzel, Tom; Ross, Marc

2006-09-18

One impediment to increasing the fuel economy standards forlight-duty vehicles is the long-standing argument that reducing vehiclemass to improve fuel economy will inherently make vehicles less safe.This technical paper summarizes and examines the research that is citedin support of this argument, and presents more recent research thatchallenges it. We conclude that the research claiming that lightervehicles are inherently less safe than heavier vehicles is flawed, andthat other aspects of vehicle design are more important to the on-roadsafety record of vehicles. This paper was prepared for a workshop onexperts in vehicle safety and fuel economy, organized by the William andFlora Hewlett Foundation, to discuss technologies and designs that can betaken to simultaneously improve vehicle safety and fuel economy; theworkshop was held in Washington DC on October 3, 2006.
Effects of vehicle type and fuel quality on real world toxic emissions from diesel vehicles

Science.gov (United States)

Nelson, Peter F.; Tibbett, Anne R.; Day, Stuart J.

Diesel vehicles are an important source of emissions of air pollutants, particularly oxides of nitrogen (NO x), particulate matter (PM), and toxic compounds with potential health impacts including volatile organic compounds (VOCs) such as benzene and aldehydes, and polycyclic aromatic hydrocarbons (PAHs). Current developments in engine design and fuel quality are expected to reduce these emissions in the future, but many vehicles exceed 10 years of age and may make a major contribution to urban pollutant concentrations and related health impacts for many years. In this study, emissions of a range of toxic compounds are reported using in-service vehicles which were tested using urban driving cycles developed for Australian conditions. Twelve vehicles were chosen from six vehicle weight classes and, in addition, two of these vehicles were driven through the urban drive cycle using a range of diesel fuel formulations. The fuels ranged in sulphur content from 24 to 1700 ppm, and in total aromatics from 7.7 to 33 mass%. Effects of vehicle type and fuel composition on emissions are reported. The results show that emissions of these toxic species were broadly comparable to those observed in previous dynamometer and tunnel studies. Emissions of VOCs and smaller PAHs such as naphthalene, which are derived largely from the combustion process, appear to be related, and show relatively little variability when compared with the variability in emissions of aldehydes and larger PAHs. In particular, aldehyde emissions are highly variable and may be related to engine operating conditions. Fuels of lower sulphur and aromatic content did not have a significant influence on emissions of VOCs and aldehydes, but tended to result in lower emissions of PAHs. The toxicity of vehicle exhaust, as determined by inhalation risk and toxic equivalency factor (TEF)-weighted PAH emissions, was reduced with fuels of lower aromatic content.
The performances of the LPG-fueled vehicle

International Nuclear Information System (INIS)

Anon.

1996-01-01

Todays, LPG-fueled vehicles are simply equipped with transformed classical petrol engines. The LPG consumption is greater but the emission of pollutants is greatly reduced (from 40 to 98% for the CO and from 30 to 80% for the HC and NOx, depending on the temperature of use). This short paper summarizes the environmental advantages of the LPG-fueled vehicles and the forthcoming technological evolutions expected in Europe, Japan and the USA. (J.S.)
Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle

Science.gov (United States)

Conversions Hybrid and Plug-In Electric Vehicle Conversions to someone by E-mail Share Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle Conversions on Facebook Tweet about Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle Conversions on Twitter Bookmark Alternative
Advanced PEFC development for fuel cell powered vehicles

Science.gov (United States)

Kawatsu, Shigeyuki

Vehicles equipped with fuel cells have been developed with much progress. Outcomes of such development efforts include a Toyota fuel cell electric vehicle (FCEV) using hydrogen as the fuel which was developed and introduced in 1996, followed by another Toyota FCEV using methanol as the fuel, developed and introduced in 1997. In those Toyota FCEVs, a fuel cell system is installed under the floor of each RAV4L, to sports utility vehicle. It has been found that the CO concentration in the reformed gas of methanol reformer can be reduced to 100 ppm in wide ranges of catalyst temperature and gas flow rate, by using the ruthenium (Ru) catalyst as the CO selective oxidizer, instead of the platinum (Pt) catalyst known from some time ago. It has been also found that a fuel cell performance equivalent to that with pure hydrogen can be ensured even in the reformed gas with the carbon monoxide (CO) concentration of 100 ppm, by using the Pt-Ru (platinum ruthenium alloy) electrocatalyst as the anode electrocatalyst of a polymer electrolyte fuel cell (PEFC), instead of the Pt electrocatalyst known from some time ago.
Alternative Fuel Vehicle Forecasts : Final report.

Science.gov (United States)

2016-04-01

Federal and state fuel taxes account for the largest share of the Texas State Highway Fund at 48 percent and 29 percent, respectively, in Fiscal Year 2015. These taxes are levied on a per-gallon basis, meaning that as vehicles get more fuel efficient...
A fuel-based approach to estimating motor vehicle exhaust emissions

Science.gov (United States)

Singer, Brett Craig

Motor vehicles contribute significantly to air pollution problems; accurate motor vehicle emission inventories are therefore essential to air quality planning. Current travel-based inventory models use emission factors measured from potentially biased vehicle samples and predict fleet-average emissions which are often inconsistent with on-road measurements. This thesis presents a fuel-based inventory approach which uses emission factors derived from remote sensing or tunnel-based measurements of on-road vehicles. Vehicle activity is quantified by statewide monthly fuel sales data resolved to the air basin level. Development of the fuel-based approach includes (1) a method for estimating cold start emission factors, (2) an analysis showing that fuel-normalized emission factors are consistent over a range of positive vehicle loads and that most fuel use occurs during loaded-mode driving, (3) scaling factors relating infrared hydrocarbon measurements to total exhaust volatile organic compound (VOC) concentrations, and (4) an analysis showing that economic factors should be considered when selecting on-road sampling sites. The fuel-based approach was applied to estimate carbon monoxide (CO) emissions from warmed-up vehicles in the Los Angeles area in 1991, and CO and VOC exhaust emissions for Los Angeles in 1997. The fuel-based CO estimate for 1991 was higher by a factor of 2.3 +/- 0.5 than emissions predicted by California's MVEI 7F model. Fuel-based inventory estimates for 1997 were higher than those of California's updated MVEI 7G model by factors of 2.4 +/- 0.2 for CO and 3.5 +/- 0.6 for VOC. Fuel-based estimates indicate a 20% decrease in the mass of CO emitted, despite an 8% increase in fuel use between 1991 and 1997; official inventory models predict a 50% decrease in CO mass emissions during the same period. Cold start CO and VOC emission factors derived from parking garage measurements were lower than those predicted by the MVEI 7G model. Current inventories
Developments in batteries and fuel cells for electric and hybrid electric vehicles

International Nuclear Information System (INIS)

Ahmed, R.

2013-01-01

Due to ever increasing threats of climate change, urban air pollution and costly and depleting oil and gas sources a lot of work is being done for the development of electric vehicles. Hybrid electric vehicles, plug-in hybrid electric vehicles and all electric vehicles are powered by batteries or by hydrogen and fuel cells are the main types of vehicles being developed. Main types of batteries which can be used for electric vehicles are lead-acid, Ni-Cd, Nickel-Metal-Hybrid ( NiMH) and Lithium-ion (Li-ion) batteries which are discussed and compared. Lithium ion battery is the mostly used battery. Developments in the lithium ion batteries are discussed and reviewed. Redox flow batteries are also potential candidates for electric vehicles and are described. Hybrid electric vehicles can reduce fuel consumption considerably and is a good midterm solution. Electric and hybrid electric vehicles are discussed. Electric vehicles are necessary to mitigate the effects of pollution and dependence on oil. For all the electric vehicles there are two options: batteries and fuel Cells. Batteries are useful for small vehicles and shorter distances but for vehicle range greater than 150 km fuel cells are superior to batteries in terms of cost, efficiency and durability even using natural gas and other fuels in addition to hydrogen. Ultimate solution for electric vehicles are hydrogen and fuel cells and this opinion is also shared by most of the automobile manufacturers. Developments in fuel cells and their applications for automobiles are described and reviewed. Comparisons have been done in the literature between batteries and fuel cells and are described. (author)
Taxation on vehicle fuels: its impacts on switching to cleaner fuels

International Nuclear Information System (INIS)

Hung, W.-T.

2006-01-01

Vehicular consumption of fossil fuel contributes over 90% of air pollution in Hong Kong. A key strategy to improve Hong Kong's air quality is to discourage dirty fuels (e.g., leaded petrol and high-sulphur diesel) and to promote the use of clean fuels (e.g., low-sulphur diesel and liquefied petroleum gas (LPG)). This paper presents the empirical evidence on the effectiveness of the Government's clean fuel programs that offer tax subsidy to lower the consumption cost of such fuels. For the cases of unleaded petrol and ultra-low-sulphur diesel, lower fuel duties were offered so that the prices of these fuels were below those of leaded petrol and conventional diesel. Conventional petrol and diesel were phased out. In order to decide on the level of fuel duty concessions required to introduce LPG for taxis and bio-diesel for other vehicles, various Government-run trial programs were introduced to obtain cost estimates of using these alternative cleaner fuels. LPG using vehicles were subsequently exempted from the fuel duty in order to attract taxi and light bus operators to switch to LPG. It is apparent that the higher the subsidy, the faster is the rate at which switching to cleaner fuels takes place
LNG market: future clouded by uncertainty

Energy Technology Data Exchange (ETDEWEB)

Segal, J

1979-12-01

The emergence of a US national energy policy playing down the role of LNG, along with a growing trend toward unfavorable production and pricing policies by LNG-exporting nations, will limit international LNG trade to about 9-10.5 billion CF/day by 1985, instead of the 13.4-15 billion CF predicted previously. In the US, LNG now stands fifth in priority as a baseload supply source, following conventional Lower 48 supplies, Alaskan pipeline gas, imports from Canada and Mexico, and domestic synthetic gas. Despite this federal policy and the adjoined decision to apply incremental pricing to future LNG imports, two new projects will soon come on-stream in the US: one to receive 450 million CF/day of Algerian gas at Lake Charles, La., and another to receive 539 million CF/day from Indonesia and 431 million CF/day from Alaska at a terminal in California.
The Japanese approach to financing LNG projects

International Nuclear Information System (INIS)

Aoki, Wataru

1995-01-01

The Japanese approach approach to financing LNG project has been what could be called a combined purchase and finance system which has been arranged mainly at the initiative of japan's Sogo Shosh (general trading companies) with the support of japanese governmental financial agencies and a purchase commitment from japanese utilities. In the QATARGAS project, despite it being the first greenfield LNG project in decade since North West Shelf Australia LNG project, financing for the LNG plant phase has been successfully arranged through Japanese financing. The structuring of the financial facilities for the QATARGAS project seems to have lessons for future development of the next generation of greenfield LNG projects. Discharge of the parties' liability, proper sharing of the risk burden and reconfirmation of the spirit of mutual understanding and trust among the parties concerned are key factors for the success of any new LNG project in the future. (Author)
Hydrogen fuel cell vehicles for the 3rd millenniums

International Nuclear Information System (INIS)

Fahmy, F.H.

2006-01-01

As the world population increases, so does the demand for transportation. Automobiles, being the most common means of transportation are on of the main sources pollution. Therefore, in order to meet the needs of society and to protect the environment, scientists began looking for a new solution to this problem. Before they suggested any answers, the scientists first looked at all aspects surrounding the issue. Fuel cell can be promoted energy diversity and a transition to renewable energy sources. This paper presents a new friendly environmental vehicles. The fuel of this vehicles is a renewable sources, solar radiation, PV arrays, electrolyzer, hydrogen and fuel cell. All the results show the capability of vehicle's design with all the details of each main component for several varieties of vehicles for transportation. This new idea realizes clean and healthy environment vehicles
40 CFR 600.206-86 - Calculation and use of fuel economy values for gasoline-fueled, diesel, and electric vehicle...

Science.gov (United States)

2010-07-01

... values for gasoline-fueled, diesel, and electric vehicle configurations. 600.206-86 Section 600.206-86...-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year... values for gasoline-fueled, diesel, and electric vehicle configurations. (a) Fuel economy values...
75 FR 29605 - Clean Alternative Fuel Vehicle and Engine Conversions

Science.gov (United States)

2010-05-26

... Part II Environmental Protection Agency 40 CFR Parts 85 and 86 Clean Alternative Fuel Vehicle and...-0299; FRL-9149-9] RIN 2060-AP64 Clean Alternative Fuel Vehicle and Engine Conversions AGENCY... streamline the process by which manufacturers of clean alternative fuel conversion systems may demonstrate...
Vehicles with fuel cells: dream or reality

Energy Technology Data Exchange (ETDEWEB)

van den Broeck, H; Hovestreydt, G

1979-01-01

Elenco N.V. is developing a hydrogen/potassium hydroxide/air fuel cell system of 10-50 kw with a specific performance of 72 mw/sq cm and a practical operating life of 5000 hr, which will be available in 1981-82. A comparative cost study was performed for vehicles with 100% fuel cells, 100% batteries, hybrid systems of fuel cells combined with batteries that provide high power for acceleration, hydrogen combustion engines, and conventional diesel engines, for city bus fleets, light commercial vehicles, forklifts, and trucks in Holland and Belgium. Hybrid systems give the best economy and they should become competitive with diesel engines after 1990.
A dynamic simulation tool for the battery-hybrid hydrogen fuel cell vehicle

Energy Technology Data Exchange (ETDEWEB)

Moore, R.M. [Hawaii Natural Energy Institute, University of Hawaii, Manoa (United States); Ramaswamy, S.; Cunningham, J.M. [California Univ., Berkeley, CA (United States); Hauer, K.H. [xcellvision, Major-Hirst-Strasse 11, 38422 Wolfsburg (Germany)

2006-10-15

This paper describes a dynamic fuel cell vehicle simulation tool for the battery-hybrid direct-hydrogen fuel cell vehicle. The emphasis is on simulation of the hybridized hydrogen fuel cell system within an existing fuel cell vehicle simulation tool. The discussion is focused on the simulation of the sub-systems that are unique to the hybridized direct-hydrogen vehicle, and builds on a previous paper that described a simulation tool for the load-following direct-hydrogen vehicle. The configuration of the general fuel cell vehicle simulation tool has been previously presented in detail, and is only briefly reviewed in the introduction to this paper. Strictly speaking, the results provided in this paper only serve as an example that is valid for the specific fuel cell vehicle design configuration analyzed. Different design choices may lead to different results, depending strongly on the parameters used and choices taken during the detailed design process required for this highly non-linear and n-dimensional system. The primary purpose of this paper is not to provide a dynamic simulation tool that is the ''final word'' for the ''optimal'' hybrid fuel cell vehicle design. The primary purpose is to provide an explanation of a simulation method for analyzing the energetic aspects of a hybrid fuel cell vehicle. (Abstract Copyright [2006], Wiley Periodicals, Inc.)
Is LNG the way ahead for natural gas?

International Nuclear Information System (INIS)

Chabrelie, M.F.; Dhellemmes, J.; Hosanski, J.M.; Goy, A.

2004-01-01

The topic of the last 2004 meeting of the French gas association (AFG) was the liquefied natural gas (LNG) which takes a growing up share in the international gas trade. The number of liquefaction plants and re-gasification terminals have increased and liquefied natural gas tanker fleets grown to match the development of world trade. The three major French players in the LNG field are Total, which produces gas and LNG in several countries, Gaz de France (GdF) which buys in a significant quantity of LNG, and GTT which provides engineering services for shipping. To get a better inside view of the LNG question, four specialists were invited to the last AFG meeting. This paper summarizes their opinion about the following points: the world potential LNG offer and the growing up capacities (LNG development, markets, supply and demand, companies strategy), the shipping by tanker ships (membrane insulation technology, fleet uses and perspectives), convergence of LNG markets and the role of Middle-East (shipping, increase of Middle-East LNG share in the world market, major stakes for the international companies), and the constraints and opportunities of re-gasification (terminals optimization, competition for re-gasification, terminals setting up problems, technical solutions). A summary of the questions and answers with the public concludes the article. (J.S.)
The French natural gas industry

International Nuclear Information System (INIS)

1999-01-01

This little folder summarizes in few pages the main economical data of the French natural gas industry: supplies according to the country of origin, length of transport and distribution networks, LNG tanker ship fleet, underground storage capacity, population of LNG-fueled vehicles, cogeneration installations, consumption by sectors and by industrial activities, LPG consumption, supplies, distribution and sales, LPG-fuel for vehicles, CO 2 and NO x releases, equipment of households. (J.S.)

The perspectives of development of natural gas for vehicles

International Nuclear Information System (INIS)

Anon.

1996-01-01

This short paper analyses the actions carried out in the world, and in particular in France, to develop and promote the use of natural gas for vehicles (NGV). In France, a protocol of agreement was signed in June 1994 between the French car manufacturers, Gaz de France and the French Association of Natural Gas for Vehicles (AFGNV) in order to develop new kinds of gas fueled vehicles, more optimized engines, to increase the number of gas distribution stations, to ratify the new models of vehicles and the specific parts for these vehicles (composite materials tanks), to carry out R and D work on gas compressors, and to develop public and private fleets of urban buses and public service vehicles. The forthcoming application of the 'Clean Air Law' will support these actions. Significant and similar developments take place also in more than 30 other countries under the same environmental motivation and ambitious programs are planned in the USA, Japan and Argentina for the year 2000. The R and D effort now focusses on the use of LNG instead of compressed natural gas. (J.S.)
Possibilities of Using Hydrogen as Motor Vehicle Fuel

Directory of Open Access Journals (Sweden)

Zdravko Bukljaš

2005-03-01

Full Text Available Hydrogen is the fuel of the future, since it is the element ofwater (H20 whichsun·ounds us and the resources of which areunlimited. First water is divided into hydrogen and oxygen. Thepaper presents the laboratory and industrial methods of obtain·ing hydrogen, types of fuel cells for various purposes, hydrogen-propelled motor vehicles, as well as advantages and drawbacksof hydrogen used as fuel under the conditions that haveto be met in order to use it as propulsion energy for motor vehicles.
Fuel Cell Electric Vehicles: Paving the Way to Commercial Success -

Science.gov (United States)

Continuum Magazine | NREL Fuel Cell Electric Vehicles: Paving the Way to Commercial Success Powered by a fuel cell system with light-weight, high-pressure hydrogen tanks, an electric motor, a nickel -metal-hydride battery, and a power-control unit, the Toyota fuel cell electric vehicle has zero tailpipe
LNG Market: Developments in 2014 and 2015 Outlook. Enerdata Gas/LNG and Power Consulting - January 2015

International Nuclear Information System (INIS)

2015-01-01

Enerdata power and gas expert held a webinar on the important developments happened in the LNG market in 2014 and provided insight on the LNG market outlook for 2015. 2015 is the year of uncertainty for the LNG industry. We will continue to experience low LNG prices driven by temporary liquefaction over capacity. The 2015 low prices environment will continue to support domestic gas price reforms in countries such as India, China, Malaysia and Indonesia. National economies of high LNG consumers such as Japan, Korea and Taiwan will benefit from low energy cost. Import terminal operators will see their utilization rates drop at concerning levels where the balance between operating cost and revenue starts to move on the red zone. Project developers will continue to delay their FID until they can see the light out of the tunnel. Those negotiating long term contracts have the big dilemma of shall it be oil-linked or not oil-linked. Never as before the importance to have a good insight of the future will differentiate losers from winners
40 CFR 80.592 - What records must be kept by entities in the motor vehicle diesel fuel and diesel fuel additive...

Science.gov (United States)

2010-07-01

... in the motor vehicle diesel fuel and diesel fuel additive distribution systems? 80.592 Section 80.592... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA... the motor vehicle diesel fuel and diesel fuel additive distribution systems? (a) Records that must be...
Electric Vehicles - Promoting Fuel Efficiency and Renewable Energy in Danish Transport

DEFF Research Database (Denmark)

Jørgensen, Kaj

1997-01-01

Analysis of electric vehicles as energy carrier for renewable energy and fossil fuels, including comparisons with other energy carriers (hydrogen, bio-fuels)......Analysis of electric vehicles as energy carrier for renewable energy and fossil fuels, including comparisons with other energy carriers (hydrogen, bio-fuels)...
On board fuel processing for using in electric vehicles

International Nuclear Information System (INIS)

Paez, Daniel E.; Marquez, Marco A.

1999-01-01

The increase in vehicle population, the emission effects upon the environment, and the growing concern of industrialized nations to reduce oil dependency, are the arguments for the new developments that may change the automobile revolution within the next decades. However, the electricity to move the future vehicles must come from the processing of liquid fuels on board. Liquid fuels such as gasoline have the advantage of having good on-site system for distribution and supply directly to the vehicle and will compete for staying as the energy source of the future. What are the opportunities in R and D and how to take advantage of them are analyzed in this document. Liquid fuel processing technologies and fuel options are also described by PDVSA-INTEVEP
Natural Gas and CO2 Price Variation: Impact on the Relative Cost-Efficiency of LNG and Pipelines

OpenAIRE

Øverland, Indra; Ulvestad, Marte

2012-01-01

This article develops a formal model for comparing the cost structure of the two main transport options for natural gas: liquefied natural gas (LNG) and pipelines. In particular, it evaluates how variations in the prices of natural gas and greenhouse gas emissions affect the relative cost-efficiency of these two options. Natural gas is often promoted as the most environmentally friendly of all fossil fuels, and LNG as a modern and efficient way of transporting it. Some research has been carri...
Preferences for alternative fuel vehicles by Dutch local governments

NARCIS (Netherlands)

Rijnsoever, F.J. van; Hagen, P.; Willems, M

2013-01-01

Using a choice model, we estimate the preferences for alternative fuel vehicles by Dutch local governments. The analysis shows that local governments are willing to pay between 25% and 50% extra for an alternative fuel vehicle without a serious loss of utility. Further, local emissions are an
Fuels demand by light vehicles and motorcycles In Brazil

Energy Technology Data Exchange (ETDEWEB)

Gomez, Jose Manoel Antelo [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2010-07-01

The purpose of this paper is to analyze the consumption of gasoline, alcohol and natural gas vehicle (NGV) by light vehicles and motorcycles in Brazil. Through the estimation of fleets per consumption class, in an environment influenced by a new engine technology (flex-fuel), this exercise estimates the fleet-elasticity of cars (and motorcycles) powered by gasoline, hydrated alcohol, natural gas vehicle (NGV) and flex-fuel, in addition to the income elasticity within the period from January, 2000 to December, 2008. This paper uses an alternative variable as income proxy and estimates the five different fleets through the combination of vehicles sales and scrapping curves. This paper's conclusion is that given specific issues of the Brazilian fuel market, in special prices and technological innovations, the fleets' equations for the consumption of the three fuels represent in a more significant manner the relationships expected between supply and demand variables than the commonly used functions of prices and income. (author)
Fuels demand by light vehicles and motorcycles In Brazil

Energy Technology Data Exchange (ETDEWEB)

Gomez, Jose Manoel Antelo [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2010-07-01

The purpose of this paper is to analyze the consumption of gasoline, alcohol and natural gas vehicle (NGV) by light vehicles and motorcycles in Brazil. Through the estimation of fleets per consumption class, in an environment influenced by a new engine technology (flex-fuel), this exercise estimates the fleet-elasticity of cars (and motorcycles) powered by gasoline, hydrated alcohol, natural gas vehicle (NGV) and flex-fuel, in addition to the income elasticity within the period from January, 2000 to December, 2008. This paper uses an alternative variable as income proxy and estimates the five different fleets through the combination of vehicles sales and scrapping curves. This paper's conclusion is that given specific issues of the Brazilian fuel market, in special prices and technological innovations, the fleets' equations for the consumption of the three fuels represent in a more significant manner the relationships expected between supply and demand variables than the commonly used functions of prices and income. (author)
Algeria's response to future LNG needs: The revamping of its LNG plants

International Nuclear Information System (INIS)

Bendani, A.; Rekkab, O.

1992-01-01

Since the beginning of the sixties, Algeria decided to participate in the international commerce of gas through its LNG. Four plants have thus been built and started in 1964, 1972, 1978 and 1981. Following the decrease in world LNG demand in the eighties, these plants built to supply 30 billion M 3 have not been operated at their full capacities. As a result, the plant equipment has suffered from this situation of partial operation (excessive shutdowns and startups). In order for SONATRACH to participate as it wishes in the expected increase in world LNG demand, two alternatives are possible to achieve this objective: Rehabilitate existing plants to enable them to operate safety and continuously to their full capacities or, build new plants. It is the first alternative that has been selected and the previous plant constructors have been selected for their renovation
77 FR 47043 - Work Group on Measuring Systems for Electric Vehicle Fueling

Science.gov (United States)

2012-08-07

... Systems for Electric Vehicle Fueling AGENCY: National Institute of Standards and Technology, Commerce... electric vehicle fuel. There is no cost for participating in the Work Group. No proprietary information... and sell electricity dispensed as a vehicle fuel) and to ensure that the prescribed methodologies and...
LNG and LPG total involvement of Pullman Kellogg

Energy Technology Data Exchange (ETDEWEB)

1978-10-01

A discussion of Pullman Kellogg activity covers a new LNG terminal in Belgium; construction of LNG 2 for Sonatrach in Algeria; an LPG recovery system in Kuwait; the Trunkline Gas Co. LNG project at Lake Charles, La.; and the Cove Point, Md., facility for Columbia Gas System Inc. and Consolidated Natural Gas Co., which will be capable of mooring two 750,000 bbl LNG tankers simultaneously.
40 CFR 600.207-08 - Calculation and use of vehicle-specific 5-cycle-based fuel economy values for vehicle...

Science.gov (United States)

2010-07-01

...-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year... for each vehicle under § 600.114-08 and as approved in § 600.008-08 (c), are used to determine vehicle... fuel economy value exists for an electric vehicle configuration, all values for that vehicle...
A basic study on underground storage of LNG

Energy Technology Data Exchange (ETDEWEB)

Kim, Min-Kyu; Lee, Kyung-Han; Kang, Sun-Duck [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

1999-12-01

In 1997, import of LNG was 11,378 thousand of about 2.3 billion US dollars. The demand of LNG(Liquefied Natural Gas) in Korea has been increased since 1987 with the rate of 20% annually. It is also estimated that this trend will be continued until 2010. Long-term estimation says that demand will increase with 9.1% and total demand of 2010 will be 23 million ton that is four times larger than that of 1994. Bases of unloading and store of LNG is necessary to complete the network of LNG distribution system to cover all of the country from import to final supply terminal at home. The construction plan of LNG bases with 49 tanks was published and is going on now at three bases, Pyungtaek, Incheon and Tongyoung. The total cost for this construction will be over 5,400 billion Won. All the LNG tanks are planned to build on the surface. The construction of LNG tanks on the surfaces is conventional but it damage the surface green area and is very vulnerable on safety, especially in Korea Peninsula with potentially unstable of military confrontation. And Korea is so small and limited in available land that it is not easy to find proper places for construction of more LNG tanks on surface. Underground LNG stores in rock will be a good alternative for tanks on surface in the view points of environmental and safety. It is also reported that it can be cheaper than that of on surfaces. It is well known that bed rocks in Korea is good to build underground structure like LNG stores. This report is basic research to seek for the possibility of LNG store construction in underground rocks. The important two questions on it is that whether it is possible technically and economically or not. The technical focus in this report is the stability of underground cavern for storage of LNG, energy conservation in operation, tightness against leakage of stored gas to surface and safety. Some statistic on LNG in Korea is given for this study with its future. (author). 25 refs., 36 tabs., 88 figs.
The sustainability of LNG evaporation

NARCIS (Netherlands)

Stougie, L.; Van der Kooi, H.J.

2011-01-01

Numerous LNG (Liquefied Natural Gas) import terminals are under construction to fulfil the growing demand for energy carriers. After storage in tanks, the LNG needs to be heated and evaporated, also called ‘regasified’, to the natural gas needed in households and industry. Several options exist for
Asia-Pacific focus of coming LNG trade boom

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that the Asia-Pacific region remains the centerpiece of a booming world trade in liquefied natural gas. Biggest growth in LNG demand is expected from some of the region's strongest economies such as Japan, South Korea, and Taiwan, Key LNG exporters such as Brunei, Malaysia, and Indonesia are scrambling to implement projects to meet that expected demand growth. Uncertainties cloud the outlook for Far East LNG trade, Australia, for one, is more cautious in pressing expansion of its LNG export capacity as more competing LNG expansions spring up around the world, notably in the Middle East and Africa
ON THE NECESSITY OF CHANGES IN THE STRATEGY OF UTILIZATION SHIP BOILER TECHNICAL CONDITION MAINTENANCE IN THE ASPECT OF LNG APPLIED AS FUEL

Directory of Open Access Journals (Sweden)

Andrzej ADAMKIEWICZ

2017-01-01

Full Text Available Heavy oils (HFO fuels used on ships play a part in degradation of technical condition of heat exchange surfaces of utiliza-tion boilers especially on the exhaust gas side. Presence of sulphur in these fuels is the main factor favouring degrada-tion. The upper limit for sulphur content in the fuel used outside the SECA areas equal to 3.5% is currently in force, at least until the year 2020 or 2025. The recommended by classification societies overhauls of utilization boilers are, there-fore characterized by a specially chosen strategy thanks to which it is possible to maintain their appropriate technical condition. The requirement to use fuels with low sulphur content (LSFO, which are significantly more expensive than MDO fuels, in the areas of controlled sulphur emissions also led to a further introduction of alternative fuels, such as methanol and above all liquefied natural gas (LNG, onto ships. That is especially valid for the ship owners whose vessels e.g. ferries sail mainly within SCECA This article analyses the consequences of the introduced fuel change on utilization boiler maintenance. A change in the technical condition maintenance strategy for utilization boilers has been suggested.
Estimating Vehicle Fuel Consumption and Emissions Using GPS Big Data

Directory of Open Access Journals (Sweden)

Zihan Kan

2018-03-01

Full Text Available The energy consumption and emissions from vehicles adversely affect human health and urban sustainability. Analysis of GPS big data collected from vehicles can provide useful insights about the quantity and distribution of such energy consumption and emissions. Previous studies, which estimated fuel consumption/emissions from traffic based on GPS sampled data, have not sufficiently considered vehicle activities and may have led to erroneous estimations. By adopting the analytical construct of the space-time path in time geography, this study proposes methods that more accurately estimate and visualize vehicle energy consumption/emissions based on analysis of vehicles’ mobile activities (MA and stationary activities (SA. First, we build space-time paths of individual vehicles, extract moving parameters, and identify MA and SA from each space-time path segment (STPS. Then we present an N-Dimensional framework for estimating and visualizing fuel consumption/emissions. For each STPS, fuel consumption, hot emissions, and cold start emissions are estimated based on activity type, i.e., MA, SA with engine-on and SA with engine-off. In the case study, fuel consumption and emissions of a single vehicle and a road network are estimated and visualized with GPS data. The estimation accuracy of the proposed approach is 88.6%. We also analyze the types of activities that produced fuel consumption on each road segment to explore the patterns and mechanisms of fuel consumption in the study area. The results not only show the effectiveness of the proposed approaches in estimating fuel consumption/emissions but also indicate their advantages for uncovering the relationships between fuel consumption and vehicles’ activities in road networks.

Single Fuel Concept for Croatian Army Ground Vehicles

Directory of Open Access Journals (Sweden)

Robert Spudić

2008-05-01

Full Text Available During the process of approaching the European associationsand NATO the Republic of Croatia has accepted the singlefuel concept for all ground vehicles of the Croatian Army.Croatia has also undertaken to insure that all aircraft, motorvehicles and equipment with turbo-engines or with pressurizedfuel injection, for participation in NATO and PfP led operationscan • operate using the kerosene-based aviation fuel(NATO F-34. The paper gives a brief overview and the resultsof the earned out activities in the Armed Forces of the Republicof Croatia, the expected behaviour of the motor vehicle andpossible delays caused by the use of kerosene fuel (NATOF-34 as fuel for motor vehicles. The paper also gives the advantagesand the drawbacks of the single fuel concept. By acquiringnew data in the Croatian Armed Forces and experienceexchange with other nations about the method of using fuelF-34, the development of the technologies of engine manufacturingand its vital parts or by introducing new standards in theproductjon of fuels and additives new knowledge will certainlybe acquired for providing logistics support in the area of operations,and its final implementation will be a big step forward forthe Republic of Croatia towards Europe and NATO.
Motor vehicle fuel economy, the forgotten HC control stragegy. [Hydrocarbon (HC)

Energy Technology Data Exchange (ETDEWEB)

Deluchi, M.; Wang, Quanlu; Greene, D.L.

1992-06-01

Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.
Fiscal 2000 survey report on R and D results of advanced clean energy vehicle; 2000 nendo kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With problems inherent to clean energy vehicles such as cruising distance, fuel supply and fuel consumption, ACEVs (advanced clean energy vehicles) are in demand featuring both low pollution and high efficiency compatibly. This paper explains the fiscal 2000 results of development. The target is, by using oil-alternative fuel, to reduce driving energy consumption and carbon dioxide emission to less than half and to control the life cycle cost (total of manufacturing cost, operating cost, fuel cost, etc.) to not more than twice as much as those of conventional vehicles. As ACEVs, an ANG (adsorbed natural gas) engine and flywheel battery mounted passenger car was selected, as were a CNG ceramics engine and capacitor mounted truck, CNG engine and lithium-ion battery mounted truck, LNG engine and capacitor mounted bus, and a DME engine and capacitor mounted bus. All are hybrid systems with an energy saving device. In the research of synthetic fuels, the results of the studies were summarized including the effect of various synthetic light oils on engine performance, fuel characteristics, effect of PM grain size and the optimum properties. (NEDO)
Research of design challenges and new technologies for floating LNG

Directory of Open Access Journals (Sweden)

Dong-Hyun Lee

2014-06-01

Full Text Available With the rate of worldwide LNG demand expected to grow faster than that of gas demand, most major oil companies are currently investing their resources to develop floating LNG-FLNG (i.e. LNG FSRU and LNG FPSO. The global Floating LNG (FLNG market trend will be reviewed based on demand and supply chain relationships. Typical technical issues associated with FLNG design are categorized in terms of global performance evaluation. Although many proven technologies developed through LNG carrier and oil FPSO projects are available for FLNG design, we are still faced with several technical challenges to clear for successful FLNG projects. In this study, some of the challenges encountered during development of the floating LNG facility (i.e. LNG FPSO and FSRU will be reviewed together with their investigated solution. At the same time, research of new LNG-related technologies such as combined containment system will be presented.
Alternate-Fuel Vehicles and Their Application in Schools.

Science.gov (United States)

Taggart, Chip

1991-01-01

Alternative fuels are becoming increasingly attractive from environmental, energy independence, and economic perspectives. Addresses the following topics: (1) federal and state legislation; (2) alternative fuels and their attributes; (3) practical experience with alternative-fuel vehicles in pupil transportation; and (4) options for school…
40 CFR 600.114-08 - Vehicle-specific 5-cycle fuel economy calculations.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Vehicle-specific 5-cycle fuel economy... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy... fuel economy calculations. This section applies to data used for fuel economy labeling under Subpart D...
Optimal sizing of plug-in fuel cell electric vehicles using models of vehicle performance and system cost

International Nuclear Information System (INIS)

Xu, Liangfei; Ouyang, Minggao; Li, Jianqiu; Yang, Fuyuan; Lu, Languang; Hua, Jianfeng

2013-01-01

Highlights: ► An analytical model for vehicle performance and power-train parameters. ► Quantitative relationships between vehicle performance and power-train parameters. ► Optimal sizing rules that help designing an optimal PEM fuel cell power-train. ► An on-road testing showing the performance of the proposed vehicle. -- Abstract: This paper presents an optimal sizing method for plug-in proton exchange membrane (PEM) fuel cell and lithium-ion battery (LIB) powered city buses. We propose a theoretical model describing the relationship between components’ parameters and vehicle performance. Analysis results show that within the working range of the electric motor, the maximal velocity and driving distance are influenced linearly by the parameters of the components, e.g. fuel cell efficiency, fuel cell output power, stored hydrogen mass, vehicle auxiliary power, battery capacity, and battery average resistance. Moreover, accelerating time is also linearly dependant on the abovementioned parameters, except of those of the battery. Next, we attempt to minimize fixed and operating costs by introducing an optimal sizing problem that uses as constraints the requirements on vehicle performance. By solving this problem, we attain several optimal sizing rules. Finally, we use these rules to design a plug-in PEM fuel cell city bus and present performance results obtained by on-road testing.
Life cycle comparison of fuel cell vehicles and internal combustion engine vehicles for Canada and the United States

Science.gov (United States)

Zamel, Nada; Li, Xianguo

The objective of this study is to put forward a full analysis of the impact of the difference between the Canadian and American energy realities on the life cycle of fuel cell vehicles and internal combustion engine vehicles. Electricity is a major type of energy used in the transportation sector. Electricity is needed in the production of feedstock of fuel, the production of the fuel, the production of the vehicle material and the assembly of the vehicles. Therefore, it is necessary to investigate the impact of the electricity mix difference between Canada and the United States. In the analysis, the life cycle of the fuel consists of obtaining the raw material, extracting the fuel from the raw material, transporting and storing the fuel as well as using the fuel in the vehicle. Four different methods of obtaining hydrogen were analyzed; using coal and nuclear power to produce electricity and extract hydrogen through electrolysis and via steam reforming of natural gas in a natural gas plant and in a hydrogen refueling station. It is found that fuel cell vehicle fuelled by hydrogen has lower energy consumption and greenhouse gas emissions than internal combustion engine vehicle fuelled by conventional gasoline except for hydrogen production using coal as the primary energy source in Canada and the United States. Using the Canadian electricity mix will result in lower carbon dioxide emissions and energy consumption than using the American electricity mix. For the present vehicles, using the Canadian electricity mix will save up to 215.18 GJ of energy and 20.87 t of CO 2 on a per capita basis and 26.53 GJ of energy and 6.8 t of CO 2 on a per vehicle basis. Similarly, for the future vehicles, using the Canadian electricity mix will lower the total carbon dioxide emissions by 21.15 t and the energy consumed is reduced by 218.49 GJ on a per capita basis and 26.53 GJ of energy and 7.22 t of CO 2 on a per vehicle basis. The well-to-tank efficiencies are higher with the
Alternative Fuels Data Center: Hybrid and Electric Vehicles Boom Coast to

Science.gov (United States)

Coast Hybrid and Electric Vehicles Boom Coast to Coast to someone by E-mail Share Alternative Fuels Data Center: Hybrid and Electric Vehicles Boom Coast to Coast on Facebook Tweet about Alternative Fuels Data Center: Hybrid and Electric Vehicles Boom Coast to Coast on Twitter Bookmark Alternative
Impact of reformulated fuels on motor vehicle emissions

Science.gov (United States)

Kirchstetter, Thomas

Motor vehicles continue to be an important source of air pollution. Increased vehicle travel and degradation of emission control systems have offset some of the effects of increasingly stringent emission standards and use of control technologies. A relatively new air pollution control strategy is the reformulation of motor vehicle fuels, both gasoline and diesel, to make them cleaner- burning. Field experiments in a heavily traveled northern California roadway tunnel revealed that use of oxygenated gasoline reduced on-road emissions of carbon monoxide (CO) and volatile organic compounds (VOC) by 23 +/- 6% and 19 +/- 8%, respectively, while oxides of nitrogen (NOx) emissions were not significantly affected. The introduction of reformulated gasoline (RFG) in California led to large changes in gasoline composition including decreases in alkene, aromatic, benzene, and sulfur contents, and an increase in oxygen content. The combined effects of RFG and fleet turnover between summers 1994 and 1997 were decreases in on-road vehicle exhaust emissions of CO, non-methane VOC, and NOx by 31 +/- 5, 43 +/- 8, and 18 +/- 4%, respectively. Although it was difficult to separate the fleet turnover and RFG contributions to these changes, it was clear that the effect of RFG was greater for VOC than for NOx. The RFG effect on exhaust emissions of benzene was a 30-40% reduction. Use of RFG reduced the reactivity of liquid gasoline and gasoline headspace vapors by 23 and 19%, respectively. Increased use of methyl tert-butyl ether in gasoline led to increased concentrations of highly reactive formaldehyde and isobutene in vehicle exhaust. As a result, RFG reduced the reactivity of exhaust emissions by only about 5%. Per unit mass of fuel burned, heavy-duty diesel trucks emit about 25 times more fine particle mass and 15-20 times the number of fine particles compared to light-duty vehicles. Exhaust fine particle emissions from heavy-duty diesels contain more black carbon than particulate
California's experience with alternative fuel vehicles

International Nuclear Information System (INIS)

Sullivan, C.

1993-01-01

California is often referred to as a nation-state, and in many aspects fits that description. The state represents the seventh largest economy in the world. Most of California does not have to worry about fuel to heat homes in the winter. What we do worry about is fuel for our motor vehicles, approximately 24 million of them. In fact, California accounts for ten percent of new vehicle sales in the United States each year, much of it used in the transportation sector. The state is the third largest consumer of gasoline in the world, only exceeded by the United States as a whole and the former Soviet Union. California is also a leader in air pollution. Of the nine worst ozone areas in the country cited in the 1990 Clean Air Act Amendments, two areas the Los Angeles Basin and San Diego are located in California. Five of California's cities made the top 20 smoggiest cities in the United States. In reality, all of California's major metropolitan areas have air quality problems. This paper will discuss the beginnings of California's investigations of alternative fuels use in vehicles; the results of the state's demonstration programs; and future plans to improve California's air quality and energy security in the mobile sector
Demand for alternative-fuel vehicles when registration taxes are high

DEFF Research Database (Denmark)

Mabit, Stefan Lindhard; Fosgerau, Mogens

2011-01-01

This paper investigates the potential futures for alternative-fuel vehicles in Denmark, where the vehicle registration tax is very high and large tax rebates can be given. A large stated choice dataset has been collected concerning vehicle choice among conventional, hydrogen, hybrid, bio......-diesel, and electric vehicles. We estimate a mixed logit model that improves on previous contributions by controlling for reference dependence and allowing for correlation of random effects. Both improvements are found to be important. An application of the model shows that alternative-fuel vehicles with present...... technology could obtain fairly high market shares given tax regulations possible in the present high-tax vehicle market....
40 CFR 80.550 - What is the definition of a motor vehicle diesel fuel small refiner or a NRLM diesel fuel small...

Science.gov (United States)

2010-07-01

...) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel... vehicle diesel fuel small refiner or a NRLM diesel fuel small refiner under this subpart? (a) A motor...-operational between January 1, 1999, and January 1, 2000, may apply for motor vehicle diesel fuel small...
Comparison of policies on vehicle ownership and use between Beijing and Shanghai and their impacts on fuel consumption by passenger vehicles

International Nuclear Information System (INIS)

Hao Han; Wang Hewu; Ouyang Minggao

2011-01-01

The fast growth of vehicle population in China has caused problems such as traffic congestion and excessive fuel consumption. There have been demands for policy control on growth in private vehicle travel demand. Beijing and Shanghai are China's first two cities to implement policies on vehicle ownership and use. In this paper, we compared policies in the two cities and estimated their impacts on fuel consumption by passenger vehicles. The limitation of vehicle use in Beijing provides limited but immediate reduction in fuel consumption. The limitation of vehicle ownership in Shanghai provides large potential of fuel conservation in a longer term. Under current policy, fuel consumptions by passenger vehicles in Beijing and Shanghai in 2020 were estimated to reach 7.5 and 3.9 billion liters, respectively. The experiences of Beijing and Shanghai are highly relevant for cities in China and abroad that are facing the same problems. - Research Highlights: → Beijing and Shanghai are the first two cities in China to implement policies on vehicle ownership and use. This paper compared policies in the two cities and evaluated their effectiveness. → A bottom-up model was established to simulate the fuel consumption by passenger vehicles. By using this model, fuel consumptions by passenger vehicles in Beijing and Shanghai from 1990 to 2020 under two scenarios of current policy and no policy were estimated. Under current policy, fuel consumptions by passenger vehicles in Beijing and Shanghai in 2020 were estimated to reach 7.5 and 3.9 billion liters, respectively. → This paper discussed the benefits and negative impacts of policies in Beijing and Shanghai, which are highly relevant for cities in China and abroad that are facing the problems of traffic congestion and excessive vehicle fuel consumption.
Airport electric vehicle powered by fuel cell

Science.gov (United States)

Fontela, Pablo; Soria, Antonio; Mielgo, Javier; Sierra, José Francisco; de Blas, Juan; Gauchia, Lucia; Martínez, Juan M.

Nowadays, new technologies and breakthroughs in the field of energy efficiency, alternative fuels and added-value electronics are leading to bigger, more sustainable and green thinking applications. Within the Automotive Industry, there is a clear declaration of commitment with the environment and natural resources. The presence of passenger vehicles of hybrid architecture, public transport powered by cleaner fuels, non-aggressive utility vehicles and an encouraging social awareness, are bringing to light a new scenario where conventional and advanced solutions will be in force. This paper presents the evolution of an airport cargo vehicle from battery-based propulsion to a hybrid power unit based on fuel cell, cutting edge batteries and hydrogen as a fuel. Some years back, IBERIA (Major Airline operating in Spain) decided to initiate the replacement of its diesel fleet for battery ones, aiming at a reduction in terms of contamination and noise in the surrounding environment. Unfortunately, due to extreme operating conditions in airports (ambient temperature, intensive use, dirtiness, …), batteries suffered a very severe degradation, which took its toll in terms of autonomy. This reduction in terms of autonomy together with the long battery recharge time made the intensive use of this fleet impractical in everyday demanding conditions.
49 CFR 193.2623 - Inspecting LNG storage tanks.

Science.gov (United States)

2010-10-01

... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY LIQUEFIED NATURAL GAS FACILITIES: FEDERAL SAFETY STANDARDS Maintenance § 193.2623 Inspecting LNG storage tanks. Each LNG... 49 Transportation 3 2010-10-01 2010-10-01 false Inspecting LNG storage tanks. 193.2623 Section 193...
Meeting U.S. passenger vehicle fuel economy standards in 2016 and beyond

International Nuclear Information System (INIS)

Cheah, Lynette; Heywood, John

2011-01-01

New fuel economy standards require new U.S. passenger vehicles to achieve at least 34.1 miles per gallon (MPG) on average by model year 2016, up from 28.8 MPG today. In this paper, the magnitude, combinations and timings of the changes required in U.S. vehicles that are necessary in order to meet the new standards, as well as a target of doubling the fuel economy within the next two decades are explored. Scenarios of future vehicle characteristics and sales mix indicate that the 2016 mandate is aggressive, requiring significant changes starting from today. New vehicles must forgo horsepower improvements, become lighter, and a greater number will use advanced, more fuel-efficient powertrains, such as smaller turbocharged engines, hybrid-electric drives. Achieving a factor-of-two increase in fuel economy by 2030 is also challenging, but more feasible since the auto industry will have more lead time to respond. A discussion on the feasibility of meeting the new fuel economy mandate is included, considering vehicle production planning realities and challenges in deploying new vehicle technologies into the market. - Research Highlights: → The new 2016 fuel economy standards for passenger vehicles in the U.S. can be met, but are aggressive. → Future vehicles must forgo horsepower improvements, become lighter, and a greater number will use advanced, more fuel efficient powertrains. → The challenge of meeting the fuel economy targets is defined by both the magnitude and the timing of these requirements. → Doubling the fuel economy by 2030 is also challenging, but more feasible since the auto industry will have more lead time to respond.
Natural Gas as a Future Fuel for Heavy-Duty Vehicles

International Nuclear Information System (INIS)

Wai-Lin Litzke; James Wegrzyn

2001-01-01

In addition to their significant environmental impacts, medium-duty and heavy-duty (HD) vehicles are high volume fuel users. Development of such vehicles, which include transit buses, refuse trucks, and HD Class 6-8 trucks, that are fueled with natural gas is strategic to market introduction of natural gas vehicles (NGV). Over the past five years the Department of Energy's (DOE) Office of Heavy Vehicle Technologies (OHVT) has funded technological developments in NGV systems to support the growth of this sector in the highly competitive transportation market. The goals are to minimize emissions associated with NGV use, to improve on the economies of scale, and to continue supporting the testing and safety assessments of all new systems. This paper provides an overview of the status of major projects under a program supported by DOE/OHVT and managed by Brookhaven National Laboratory. The discussion focuses on the program's technical strategy in meeting specific goals proposed by the N GV industry and the government. Relevant projects include the development of low-cost fuel storage, fueling infrastructure, and HD vehicle applications
Coordination of ministry actions related to the use of liquefied natural gas for marine fuel - A maritime challenge to face collectively

International Nuclear Information System (INIS)

Jouffray, Jean-Francois; Erhardt, Jean-Bernard; Allais, Vincent

2013-02-01

As France remained apart from a movement of adoption of liquefied natural gas (LNG) in maritime applications, this report first discusses the different fuels used by ships (conventional fuels, LNG, fuel energy efficiency, LNG engines and tanks). Then, after having recalled international constraints related to atmospheric emissions by ships (MARPOL convention, European legal framework) and noticed the possible transfer to other transport mode in case of change of fuel, the authors discuss the possible solutions and show that LNG allows environmental objectives to be met whereas other conventional fuels present several drawbacks. They comment the results of some European studies on the use of LNG, propose an overview of LNG resources, availability and prices, and indicate current projects in the world. They study the implications of introduction of LNG for ships in France in terms of infrastructures, of regulation, and of compliance with different European policies. They discuss different aspects related to the creation of the associated market, the commitment of economic stakeholders, industrial stakes, pilot projects and the issue of investment financing
The cost of fuel economy in the Indian passenger vehicle market

International Nuclear Information System (INIS)

Chugh, Randy; Cropper, Maureen; Narain, Urvashi

2011-01-01

To investigate how fuel economy is valued in the Indian car market, we compute the cost to Indian consumers of purchasing a more fuel-efficient vehicle and compare it to the benefit of lower fuel costs over the life of the vehicle. We estimate hedonic price functions for four market segments (petrol hatchbacks, diesel hatchbacks, petrol sedans, and diesel sedans) to compute 95% confidence intervals for the marginal cost to the consumer for an increase in fuel economy. We find that the associated present value of fuel savings falls within the 95% confidence interval for most specifications, in all market segments, for the years 2002 through 2006. Thus, we fail to consistently reject the hypothesis that consumers appropriately value fuel economy. - Highlights: → We examine the tradeoffs faced by new vehicle consumers in India. → We use hedonic price functions and instrumental variables. → We find no support for the hypothesis that consumers undervalue fuel economy. → Some consumers are willing to forgo substantial potential savings to own their preferred vehicle.

World economic growth pushing LNG use

International Nuclear Information System (INIS)

Brown, R.L.; Clary, R.

1997-01-01

Natural gas, especially liquefied (LNG), is in position to participate in the energy growth now being triggered by strong worldwide economic growth, increasingly open markets, and expanding international trade. Natural gas is abundant, burns cleanly, and is highly efficient in combined-cycle, gas-turbine power plants. Moreover, the comparative remoteness of much of the resource base to established and emerging markets can make LNG a compelling processing and transportation alternative. Discussed here are the resource distribution and emerging market opportunities that can make LNG attractive for monetizing natural-gas reserves
76 FR 19829 - Clean Alternative Fuel Vehicle and Engine Conversions

Science.gov (United States)

2011-04-08

... INFORMATION CONTACT: Amy Bunker, Compliance and Innovative Strategies Division, U.S. Environmental Protection... Vehicle/Engine Selection D. Mixed-Fuel and Dual-Fuel Conversions E. Vehicle/Engine Labels, Packaging Labels, and Marketing F. Compliance 1. Emission Standards a. Light-Duty and Heavy-Duty Chassis Certified...
Using Fuel Cells to Increase the Range of Battery Electric Vehicles | News

Science.gov (United States)

| NREL Using Fuel Cells to Increase the Range of Battery Electric Vehicles Using Fuel Cells to significantly lower capital and lifecycle costs than additional battery capacity alone. And while fuel-cell -Duty Battery Electric Vehicles through the Use of Hydrogen Fuel Cells"-presented at the Society of
Clean Cities Strategic Planning White Paper: Light Duty Vehicle Fuel Economy

Energy Technology Data Exchange (ETDEWEB)

Saulsbury, Bo [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hopson, Dr Janet L [Univ. of Tennessee, Knoxville, TN (United States); Greene, David [Univ. of Tennessee, Knoxville, TN (United States); Gibson, Robert [Univ. of Tennessee, Knoxville, TN (United States)

2015-04-01

Increasing the energy efficiency of motor vehicles is critical to achieving national energy goals of reduced petroleum dependence, protecting the global climate, and promoting continued economic prosperity. Even with fuel economy and greenhouse gas emissions standards and various economic incentives for clean and efficient vehicles, providing reliable and accurate fuel economy information to the public is important to achieving these goals. This white paper reviews the current status of light-duty vehicle fuel economy in the United States and the role of the Department of Energy (DOE) Clean Cities Program in disseminating fuel economy information to the public.
The economic value of LNG in the Korean manufacturing industry

International Nuclear Information System (INIS)

Park, Sun-Young; Yoo, Seung-Hoon

2013-01-01

Although LNG is an important input to industrial production for manufacturing firms, its economic value has been rarely investigated in the literature. This paper attempts to estimate the economic value of LNG in Korea's manufacturing sector by employing the concept of the value of marginal product (VMP). For this, we used data on 328 firms using LNG as an input. Two types of production functions (the Cobb–Douglas and trans-log functions) are applied. The result of the specification test indicates that the trans-log function is more appropriate for estimating the data. The output elasticity and VMP of industrial LNG are estimated to be 0.1346 and KRW 6844 (USD 6.22) per m 3 , respectively. The results have important implications for various areas of industrial LNG management. For example, any cost–benefit analysis of new projects providing industrial LNG requires information on the economic value of industrial LNG. In addition, such information is useful for the Korean government's future policies on LNG pricing. - Highlights: • We estimate the economic value of LNG in the Korean manufacturing industry. • We employ the concept of the value of marginal product (VMP). • The VMP of industrial LNG is estimated to be KRW 6844 (USD 6.22) per m 3 . • It significantly outweighs the price of industrial LNG (KRW 629.4 per m 3 )
Russian LNG: The Long Road to Export

International Nuclear Information System (INIS)

Mitrova, Tatiana

2013-12-01

On December 1, 2013 a law on liquefied natural gas (LNG) export liberalization came into legal force in Russia. The law grants two categories of companies other than Russia's state gas giant Gazprom and its subsidiary companies the right to export LNG: (1) users of mineral resources that have a license to construct an LNG plant or to send their gas production for liquefaction, and (2) companies that are more than 50% owned by the Russian government, for gas produced from Russian offshore fields or under production-sharing agreements. This is-without exaggeration-a historic decision for the Russian gas industry, the path to which was certainly not easy. Recent years have seen a radical change in the global economic climate, which has changed the dynamics of the European gas market (gas demand decline and Russian gas import reduction, changing pricing mechanism for a much higher share of spot indexing, European Commission anti-trust investigations against Gazprom, etc) and is increasingly pushing Russia to diversify its gas exports. However, diversifying exports through the development of LNG has proven to be not so simple. Over the past 20 years, with the exception of the Sakhalin-2 project, structured under a project-sharing agreement (PSA) rather than in the framework of national legislation, all other projects failed to come close to completion. The Kharasavey and Baltic LNG projects were abandoned in the early stages of project evaluation, while the Shtokman project progressed to the point of the operating company being created, but in the end was postponed indefinitely. The first stage of LNG development in Russia ended in failure. However, the Russian government considers the development of LNG exports to be a priority, which can be evidenced in all official policy papers. It is believed that LNG will help in achieving a set of objectives, namely: increasing the absolute volume of exports, allowing the country to enter into previously inaccessible markets
Policy Pathways: Improving the Fuel Economy of Road Vehicles - A policy package

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

The transportation sector accounts for approximately one-fifth of global final energy consumption and will account for nearly all future growth in oil use, particularly for road vehicles. The right policy mix can allow countries to improve the fuel economy of road vehicles, which in turn can enhance energy security and reduce CO2 emissions. Improving the Fuel Economy of Road Vehicles highlights lessons learned and examples of good practices from countries with experience in implementing fuel economy policies for vehicles. The report, part of the IEA’s Policy Pathway series, outlines key steps in planning, implementation, monitoring and evaluation. It complements the IEA Technology Roadmap: Fuel Economy for Road Vehicles, which outlines technical options, potentials, and costs towards improvement in the near, medium and long term.
Model and algorithm for bi-fuel vehicle routing problem to reduce GHG emissions.

Science.gov (United States)

Abdoli, Behroz; MirHassani, Seyed Ali; Hooshmand, Farnaz

2017-09-01

Because of the harmful effects of greenhouse gas (GHG) emitted by petroleum-based fuels, the adoption of alternative green fuels such as biodiesel and compressed natural gas (CNG) is an inevitable trend in the transportation sector. However, the transition to alternative fuel vehicle (AFV) fleets is not easy and, particularly at the beginning of the transition period, drivers may be forced to travel long distances to reach alternative fueling stations (AFSs). In this paper, the utilization of bi-fuel vehicles is proposed as an operational approach. We present a mathematical model to address vehicle routing problem (VRP) with bi-fuel vehicles and show that the utilization of bi-fuel vehicles can lead to a significant reduction in GHG emissions. Moreover, a simulated annealing algorithm is adopted to solve large instances of this problem. The performance of the proposed algorithm is evaluated on some random instances.
76 FR 39477 - Revisions and Additions to Motor Vehicle Fuel Economy Label

Science.gov (United States)

2011-07-06

...The Environmental Protection Agency (EPA) and the National Highway Traffic Safety Administration (NHTSA) are issuing a joint final rule establishing new requirements for the fuel economy and environment label that will be posted on the window sticker of all new automobiles sold in the U.S. The labeling requirements apply for model year 2013 and later vehicles with a voluntary manufacturer option for model year 2012. The labeling requirements apply to passenger cars, light-duty trucks, and medium duty passenger vehicles such as larger sport-utility vehicles and vans. The redesigned label provides expanded information to American consumers about new vehicle fuel economy and fuel consumption, greenhouse gas and smog-forming emissions, and projected fuel costs and savings, and also includes a smartphone interactive code that permits direct access to additional Web resources. Specific label designs are provided for gasoline, diesel, ethanol flexible fuel, compressed natural gas, electric, plug-in hybrid electric, and hydrogen fuel cell vehicles. This rulemaking is in response to provisions in the Energy Independence and Security Act of 2007 that imposed several new labeling requirements and new advanced-technology vehicles entering the market. NHTSA and EPA believe that these changes will help consumers to make more informed vehicle purchase decisions, particularly as the future automotive marketplace provides more diverse vehicle technologies from which consumers may choose. These new label requirements do not affect the methodologies that EPA uses to generate consumer fuel economy estimates, or the automaker compliance values for NHTSA's corporate average fuel economy and EPA's greenhouse gas emissions standards. This action also finalizes a number of technical corrections to EPA's light-duty greenhouse gas emission standards program.
Fuel cell usage in motor vehicles

International Nuclear Information System (INIS)

Vellone, R.

1998-01-01

Much interest has been aroused by fuel cell usage in motor vehicles, since this technology seems to overcome the conventional limits by other kinds of drive, i.e. the high environmental impact of internal-combustion engines and the drawbacks of electric battery vehicles in terms of maximum operating range and battery recharge time. After 2010 its costs are expected to fall in competitive levels with internal-combustion engines [it
Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

DEFF Research Database (Denmark)

Nielsen, L.H.; Jørgensen K.

2000-01-01

The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore toillustrate the potential synergistic interplay...... between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalisedelectricity market are analysed. The project focuses on battery electric vehicles and fuel cell...... vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and forthe conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport...
LNG terminalil on idaraha keeld / Raimo Poom

Index Scriptorium Estoniae

Poom, Raimo

2011-01-01

Euroopa Komisjon kiirustab Balti riike LNG (vedeldatud maagaasi) terminali asukohas kokku leppima. Kolmest tingimusest, millele peab LNG terminali projekt vastama, et tekiks võimalus kandideerida EL-i toetusele
Alternative Fuels Data Center: Plug-In Hybrid Electric Vehicles

Science.gov (United States)

. Fueling and Driving Options Plug-in hybrid electric vehicle batteries can be charged by an outside sized hybrid electric vehicle. If the vehicle is driven a shorter distance than its all-electric range drives the wheels almost all of the time, but the vehicle can switch to work like a parallel hybrid at
Toxic emissions from mobile sources: a total fuel-cycle analysis for conventional and alternative fuel vehicles.

Science.gov (United States)

Winebrake, J J; Wang, M Q; He, D

2001-07-01

Mobile sources are among the largest contributors of four hazardous air pollutants--benzene, 1,3-butadiene, acetaldehyde, and formaldehyde--in urban areas. At the same time, federal and state governments are promoting the use of alternative fuel vehicles as a means to curb local air pollution. As yet, the impact of this movement toward alternative fuels with respect to toxic emissions has not been well studied. The purpose of this paper is to compare toxic emissions from vehicles operating on a variety of fuels, including reformulated gasoline (RFG), natural gas, ethanol, methanol, liquid petroleum gas (LPG), and electricity. This study uses a version of Argonne National Laboratory's Greenhouse Gas, Regulated Emissions, and Energy Use in Transportation (GREET) model, appropriately modified to estimate toxic emissions. The GREET model conducts a total fuel-cycle analysis that calculates emissions from both downstream (e.g., operation of the vehicle) and upstream (e.g., fuel production and distribution) stages of the fuel cycle. We find that almost all of the fuels studied reduce 1,3-butadiene emissions compared with conventional gasoline (CG). However, the use of ethanol in E85 (fuel made with 85% ethanol) or RFG leads to increased acetaldehyde emissions, and the use of methanol, ethanol, and compressed natural gas (CNG) may result in increased formaldehyde emissions. When the modeling results for the four air toxics are considered together with their cancer risk factors, all the fuels and vehicle technologies show air toxic emission reduction benefits.
Fuel cells for vehicle applications in cars - bringing the future closer

Science.gov (United States)

Panik, Ferdinand

Among all alternative drive systems, the fuel cell electric propulsion system has the highest potential to compete with the internal combustion engine. For this reason, Daimler-Benz AG has entered into a co-operative alliance with Ballard Power Systems, with the objectives of bringing fuel cell vehicles to the market. Apart from the fuel cell itself, fuel cell vehicles require comprehensive system technology to provide fuel and air supply, cooling, energy management, electric and electronic functions. The system technology determines to a large extent the cost, weight, efficiency, performance and overall customer benefit of fuel cell vehicles. Hence, Daimler-Benz and Ballard are pooling their expertise in fuel cell system technology in a joint company, with the aim of bringing their fuel cell vehicular systems to the stage of maturity required for market entry as early as possible. Hydrogen-fuelled zero-emission fuel cell transit `buses' will be the first market segment addressed, with an emphasis on the North American and European markets. The first buses are already scheduled for delivery to customers in late 1997. Since a liquid fuel like methanol is easier to handle in passenger cars, fuel reforming technologies are developed and will shortly be demonstrated in a prototype, as well. The presentation will cover concepts of fuel cell vehicles with an emphasis on system technology, the related testing procedures and results as well as an outline of market entry strategies.
An investigation on the fuel savings potential of hybrid hydraulic refuse collection vehicles

Energy Technology Data Exchange (ETDEWEB)

Bender, Frank A., E-mail: bender@isys.uni-stuttgart.de; Bosse, Thomas; Sawodny, Oliver

2014-09-15

Highlights: • Driving cycle acquisition in a refuse collection vehicle. • Vehicle modeling and validation for numerical simulations based on the measured driving cycle. • Fuel consumption analysis for a conventional diesel vehicle and a hybrid hydraulic vehicle. - Abstract: Refuse trucks play an important role in the waste collection process. Due to their typical driving cycle, these vehicles are characterized by large fuel consumption, which strongly affects the overall waste disposal costs. Hybrid hydraulic refuse vehicles offer an interesting alternative to conventional diesel trucks, because they are able to recuperate, store and reuse braking energy. However, the expected fuel savings can vary strongly depending on the driving cycle and the operational mode. Therefore, in order to assess the possible fuel savings, a typical driving cycle was measured in a conventional vehicle run by the waste authority of the City of Stuttgart, and a dynamical model of the considered vehicle was built up. Based on the measured driving cycle and the vehicle model including the hybrid powertrain components, simulations for both the conventional and the hybrid vehicle were performed. Fuel consumption results that indicate savings of about 20% are presented and analyzed in order to evaluate the benefit of hybrid hydraulic vehicles used for refuse collection.
An investigation on the fuel savings potential of hybrid hydraulic refuse collection vehicles

International Nuclear Information System (INIS)

Bender, Frank A.; Bosse, Thomas; Sawodny, Oliver

2014-01-01

Highlights: • Driving cycle acquisition in a refuse collection vehicle. • Vehicle modeling and validation for numerical simulations based on the measured driving cycle. • Fuel consumption analysis for a conventional diesel vehicle and a hybrid hydraulic vehicle. - Abstract: Refuse trucks play an important role in the waste collection process. Due to their typical driving cycle, these vehicles are characterized by large fuel consumption, which strongly affects the overall waste disposal costs. Hybrid hydraulic refuse vehicles offer an interesting alternative to conventional diesel trucks, because they are able to recuperate, store and reuse braking energy. However, the expected fuel savings can vary strongly depending on the driving cycle and the operational mode. Therefore, in order to assess the possible fuel savings, a typical driving cycle was measured in a conventional vehicle run by the waste authority of the City of Stuttgart, and a dynamical model of the considered vehicle was built up. Based on the measured driving cycle and the vehicle model including the hybrid powertrain components, simulations for both the conventional and the hybrid vehicle were performed. Fuel consumption results that indicate savings of about 20% are presented and analyzed in order to evaluate the benefit of hybrid hydraulic vehicles used for refuse collection
40 CFR 80.532 - How are motor vehicle diesel fuel credits used and transferred?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false How are motor vehicle diesel fuel... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel....532 How are motor vehicle diesel fuel credits used and transferred? (a) Credit use stipulations. Motor...
LNG imports make strong recovery in 1996; exports increase also

International Nuclear Information System (INIS)

Swain, E.J.

1998-01-01

LNG imports to the US jumped in 1996 as Algerian base-load plants resumed operations following major revamps. Exports from Alaska to Japan grew by nearly 4% over 1995. Total LNG imports to the US in 1996 were 40.27 bcf compared to 17.92 bcf in 1995, an increase of 124.8%. Algeria supplied 35.32 bcf; Abu Dhabi, 4.95 bcf. About 82.3% of the imported LNG was received at Distrigas Corp.'s terminal north of Boston. The remaining LNG was received at the Pan National terminal in Lake Charles, LA. LNG imports during 1995 fell to such a low level not because of depressed US demand but because of limited supply. The paper discusses LNG-receiving terminals, base-load producers, LNG pricing, and exports
Comparison of life cycle greenhouse gases from natural gas pathways for medium and heavy-duty vehicles.

Science.gov (United States)

Tong, Fan; Jaramillo, Paulina; Azevedo, Inês M L

2015-06-16

The low-cost and abundant supply of shale gas in the United States has increased the interest in using natural gas for transportation. We compare the life cycle greenhouse gas (GHG) emissions from different natural gas pathways for medium and heavy-duty vehicles (MHDVs). For Class 8 tractor-trailers and refuse trucks, none of the natural gas pathways provide emissions reductions per unit of freight-distance moved compared to diesel trucks. When compared to the petroleum-based fuels currently used in these vehicles, CNG and centrally produced LNG increase emissions by 0-3% and 2-13%, respectively, for Class 8 trucks. Battery electric vehicles (BEVs) powered with natural gas-produced electricity are the only fuel-technology combination that achieves emission reductions for Class 8 transit buses (31% reduction compared to the petroleum-fueled vehicles). For non-Class 8 trucks (pick-up trucks, parcel delivery trucks, and box trucks), BEVs reduce emissions significantly (31-40%) compared to their diesel or gasoline counterparts. CNG and propane achieve relatively smaller emissions reductions (0-6% and 19%, respectively, compared to the petroleum-based fuels), while other natural gas pathways increase emissions for non-Class 8 MHDVs. While using natural gas to fuel electric vehicles could achieve large emission reductions for medium-duty trucks, the results suggest there are no great opportunities to achieve large emission reductions for Class 8 trucks through natural gas pathways with current technologies. There are strategies to reduce the carbon footprint of using natural gas for MHDVs, ranging from increasing vehicle fuel efficiency, reducing life cycle methane leakage rate, to achieving the same payloads and cargo volumes as conventional diesel trucks.

Fuel cell powered vehicles using supercapacitors-device characteristics, control strategies, and simulation results

Energy Technology Data Exchange (ETDEWEB)

Zhao, H.; Burke, A.F. [Institute of Transportation Studies, University of California (United States)

2010-10-15

The fuel cell powered vehicle is one of the most attractive candidates for the future due to its high efficiency and capability to use hydrogen as the fuel. However, its relatively poor dynamic response, high cost and limited life time have impeded its widespread adoption. With the emergence of large supercapacitors (also know as ultracapacitors, UCs) with high power density and the shift to hybridisation in the vehicle technology, fuel cell/supercapacitor hybrid fuel cell vehicles are gaining more attention. Fuel cells in conjunction with supercapacitors can create high power with fast dynamic response, which makes it well suitable for automotive applications. Hybrid fuel cell vehicles with different powertrain configurations have been evaluated based on simulations performed at the Institute of Transportation Studies, University of California-Davis. The following powertrain configurations have been considered: (a)Direct hydrogen fuel cell vehicles (FCVs) without energy storage (b)FCVs with supercapacitors directly connected in parallel with fuel cells (c)FCVs with supercapacitors coupled in parallel with fuel cells through a DC/DC converter (d)FCVs with fuel cells connected to supercapacitors via a DC/DC converter. (Abstract Copyright [2010], Wiley Periodicals, Inc.)
Effects of Fuel Type and Fuel Delivery System on Pollutant Emissions of Pride and Samand Vehicles

Directory of Open Access Journals (Sweden)

Akbar Sarhadi

2017-04-01

Full Text Available This research was aimed to study the effect of the type of fuel delivery system (petrol, dedicated or bifuel, the type of consumed fuel (petrol or gas, the portion of consumed fuel and also the duration of dual-fuelling in producing carbon monoxide, carbon dioxide and unburned hydrocarbons from Pride and Samand. According to research objectives, data gathering from 2000 vehicles has been done by visiting Hafiz Vehicle Inspection Center every day for 2 months. The results of this survey indicated that although there is no significant difference between various fuel delivery systems in terms of producing the carbon monoxide, carbon dioxide and unburned hydrocarbons by Samand, considering the emission amount of carbon dioxide, the engine performance of Pride in bifuel and dedicated state in GTXI and 132 types is more unsatisfactory than that of petrol state by 0.3 and 0.4%, respectively. On the other hand, consuming natural gas increases the amount of carbon monoxide emission in dual- fuel Pride by 0.18% and decreases that in dual-fuel Samand by 1.2%, which signifies the better design of Samand in terms of fuel pumps, used kit type and other engine parts to use this alternative fuel compared to Pride. Since the portion of consumed fuel and also duration of dual-fuelling does not have a significant effect on the amount of output pollutants from the studied vehicles, it can be claimed that the output substances from the vehicle exhaust are more related to the vehicle’s condition than the fuel type.
Alternative transportation fuels in the USA: government hydrogen vehicle programs

International Nuclear Information System (INIS)

Cannon, J.S.

1993-01-01

The linkage between natural gas-based transportation and hydrogen-based transportation strategies, two clean burning gaseous fuels, provides a strong policy rationale for increased government sponsorship of hydrogen vehicle research and demonstration programs. Existing federal and state government hydrogen vehicle projects are discussed in this paper: research at the NREL, alternate-fueled buses, Renewable Hydrogen for the State of Hawaii program, New York state alternative transportation fuels program, Colorado program. 9 refs
Improvement of plant reliability in PT. Badak LNG plant

International Nuclear Information System (INIS)

Achmad, S.; Somantri, A.

1997-01-01

PT. Badak's LNG sales commitment has been steadily increasing, therefore, there has been more emphasis to improve and maintain the LNG plant reliability. From plant operation historical records, Badak LNG plant experienced a high number of LNG process train trips and down time for 1977 through 1988. The highest annual number of LNG plant trips (50 times) occurred in 1983 and the longest LNG process train down time (1259 train-hours) occurred in 1988. Since 1989, PT. Badak has been able to reduce the number of LNG process train trips and down time significantly. In 1994 the number of LNG process train trips and was 18 times and the longest LNG process train down time was 377 train-hours. This plant reliability improvement was achieved by implementing plant reliability improvement programs beginning with the design of the new facilities and continuing with the maintenance and modification of the existing facilities. To improve reliability of the existing facilities, PT. Badak has been implementing comprehensive maintenance programs, to reduce the frequency and down time of the plant, such as Preventive and Predictive Maintenance as well as procurement material improvement since PT. Badak location is in a remote area. By implementing the comprehensive reliability maintenance, PT. Badak has been able to reduce the LNG process train trips to 18 and down time to 337 train hours in 1994 with the subsequent maintenance cost reduction. The average PT. Badak plant availability from 1985 to 1995 is 94.59%. New facilities were designed according to the established PT. Badak design philosophy, master plan and specification. Design of new facilities was modified to avoid certain problems from past experience. (au)
77 FR 36423 - Labeling Requirements for Alternative Fuels and Alternative Fueled Vehicles

Science.gov (United States)

2012-06-19

... delivered to the following address: Federal Trade Commission, Office of the Secretary, Room H-113 (Annex N... cell, advanced lean burn, and hybrid motor vehicles) that were added to the definition of ``alternative... legislation (i.e., lean burn, hybrid, and fuel cell vehicles). No comments opposed this approach. Edison...
Impact of Solar Control PVB Glass on Vehicle Interior Temperatures, Air-Conditioning Capacity, Fuel Consumption, and Vehicle Range

Energy Technology Data Exchange (ETDEWEB)

Rugh, J.; Chaney, L.; Venson, T.; Ramroth, L.; Rose, M.

2013-04-01

The objective of the study was to assess the impact of Saflex1 S-series Solar Control PVB (polyvinyl butyral) configurations on conventional vehicle fuel economy and electric vehicle (EV) range. The approach included outdoor vehicle thermal soak testing, RadTherm cool-down analysis, and vehicle simulations. Thermal soak tests were conducted at the National Renewable Energy Laboratory's Vehicle Testing and Integration Facility in Golden, Colorado. The test results quantified interior temperature reductions and were used to generate initial conditions for the RadTherm cool-down analysis. The RadTherm model determined the potential reduction in air-conditioning (A/C) capacity, which was used to calculate the A/C load for the vehicle simulations. The vehicle simulation tool identified the potential reduction in fuel consumption or improvement in EV range between a baseline and modified configurations for the city and highway drive cycles. The thermal analysis determined a potential 4.0% reduction in A/C power for the Saflex Solar PVB solar control configuration. The reduction in A/C power improved the vehicle range of EVs and fuel economy of conventional vehicles and plug-in hybrid electric vehicles.
Reducing the fuel use and greenhouse gas emissions of the US vehicle fleet

International Nuclear Information System (INIS)

Bandivadekar, Anup; Cheah, Lynette; Evans, Christopher; Groode, Tiffany; Heywood, John; Kasseris, Emmanuel; Kromer, Matthew; Weiss, Malcolm

2008-01-01

The unrelenting increase in the consumption of oil in the US light-duty vehicle fleet (cars and light trucks) presents an extremely challenging energy and environmental problem. A variety of propulsion technologies and fuels have the promise to reduce petroleum use and greenhouse gas emissions from motor vehicles. Even so, achieving a noticeable reduction on both fronts in the near term will require rapid penetration of these technologies into the vehicle fleet, and not all alternatives can meet both objectives simultaneously. Placing a much greater emphasis on reducing fuel consumption rather than improving vehicle performance can greatly reduce the required market penetration rates. Addressing the vehicle performance-size-fuel consumption trade-off should be the priority for policymakers rather than promoting specific vehicle technologies and fuels
76 FR 53440 - Freeport LNG Development, LP; Freeport LNG Expansion, LP; FLNG Liquefaction LLC; Notice of Intent...

Science.gov (United States)

2011-08-26

.... Summary of the Planned Project Freeport plans to add natural gas liquefaction and exportation capabilities to its existing liquefied natural gas (LNG) import terminal on Quintana Island in Brazoria County... tank, and additional LNG vaporization and natural gas send-out facilities that were previously...
Impact resistance cryogenic bunker fuel tanks

NARCIS (Netherlands)

Voormeeren, L.O.; Atli-Veltin, B.; Vredeveldt, A.W.

2014-01-01

The increasing use of liquefied natural gas (LNG) as bunker fuel in ships, calls for an elaborate study regarding the risks involved. One particular issue is the vulnerability of cryogenic LNG storage tanks with respect to impact loadings, such as ship collisions and dropped objects. This requires
Alternative Fuel Fleet Vehicle Evaluations | Transportation Research | NREL

Science.gov (United States)

delivery, transit, and freight vehicles. Although biodiesel is the most commonly used alternative fuel in Diesel and Biodiesel Renewable diesel is a conventional petroleum diesel substitute produced from alternative to conventional diesel and does not require any vehicle modifications. Biodiesel is an oxygenated
Alternative Fuels and Advanced Vehicles: Resources for Fleet Managers (Clean Cities) (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Brennan, A.

2011-04-01

A discussion of the tools and resources on the Clean Cities, Alternative Fuels and Advanced Vehicles Data Center, and the FuelEconomy.gov Web sites that can help vehicle fleet managers make informed decisions about implementing strategies to reduce gasoline and diesel fuel use.
Making the case for direct hydrogen storage in fuel cell vehicles

Energy Technology Data Exchange (ETDEWEB)

James, B.D.; Thomas, C.E.; Baum, G.N.; Lomas, F.D. Jr.; Kuhn, I.F. Jr. [Directed Technologies, Inc., Arlington, VA (United States)

1997-12-31

Three obstacles to the introduction of direct hydrogen fuel cell vehicles are often states: (1) inadequate onboard hydrogen storage leading to limited vehicle range; (2) lack of an hydrogen infrastructure, and (3) cost of the entire fuel cell system. This paper will address the first point with analysis of the problem/proposed solutions for the remaining two obstacles addressed in other papers. Results of a recent study conducted by Directed Technologies Inc. will be briefly presented. The study, as part of Ford Motor Company/DOE PEM Fuel Cell Program, examines multiple pure hydrogen onboard storage systems on the basis of weight, volume, cost, and complexity. Compressed gas, liquid, carbon adsorption, and metal hydride storage are all examined with compressed hydrogen storage at 5,000 psia being judged the lowest-risk, highest benefit, near-term option. These results are combined with recent fuel cell vehicle drive cycle simulations to estimate the onboard hydrogen storage requirement for full vehicle range (380 miles on the combined Federal driving schedule). The results indicate that a PNGV-like vehicle using powertrain weights and performance realistically available by the 2004 PNGV target data can achieve approximate fuel economy equivalent to 100 mpg on gasoline (100 mpg{sub eq}) and requires storage of approximately 3.6 kg hydrogen for full vehicle storage quantity allows 5,000 psia onboard storage without altering the vehicle exterior lines or appreciably encroaching on the passenger or trunk compartments.
Report of the results of the fiscal 1997 survey. R and D of high efficiency clean energy vehicles; 1997 nendo chosa hokokusho. Kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of developing an automobile which keeps low pollution using petroleum substituting clean energy, decreases the running energy consumption to a half at least, and reduces the CO2 emission to less than a half of the conventional one at the same time, the R and D started in fiscal 1997. As to the study of a high efficiency hybrid power system, conducted were the prediction of fuel consumption performance of the system proposed, evaluation of element technology using hybrid simulator, evaluation experiment on a new hybrid vehicle, and grasp of overseas trends. In relation to the development of hybrid vehicles, the following were studied: methanol fuel cell loading hybrid vehicle, CNG engine loading hybrid vehicle, CNG ceramic engine loading hybrid truck, CNG lean burn engine loading hybrid truck, LNG engine loading hybrid bus, and DME engine loading hybrid bus. Besides, a survey on synthetic fuel and the related survey were carried out. 17 refs., 185 figs., 101 tabs.
Petro-Safe '95: 6. Annual environmental, safety and health conference and exhibition for the oil, gas and petrochemical industries. Book 3: AFV '95 and Production economics '95 conference papers

International Nuclear Information System (INIS)

Anon.

1995-01-01

Book 3 of the proceedings contains papers from two symposia: Alternative Fueled Vehicles and Production Economics. The Alternative Fueled Vehicles symposium is divided into 3 sections which cover: (1) Hardware and vehicles--school bus fleets and LNG; (2) Fuels and infrastructure--CNG fueling facilities, reformulated gasoline and clean diesel, LNG, future supply trends and domestic energy security, safety issues, and methanol; and (3) Regulatory issues--Clean Cities program, Energy Policy Act and state legislation, Employee Trip Reduction program, and public awareness. The papers in the Production Economics symposium deal with cost-effective methods for marginal field development; economic considerations for offshore platforms and systems; enhanced oil recovery economics; floating production economics; and capital versus operating costs in oil and gas production. Thirty-five papers have been processed separately for inclusion on the data base
The conception of the LNG implementation in Poland

International Nuclear Information System (INIS)

Skwarczynski, S.; Zola, P.

2006-01-01

The main issues concerning world LNG market, technical applications and the potential growth of the market have been described in the article. The conception of introducing LNG on Polish gas market assumes that a LNG terminal will be built on the Baltic Sea shore along with the infrastructure necessary to store and transmit gas to the national gas pipeline grid. (authors)
Fuel Cell Power Plants Renewable and Waste Fuels

Science.gov (United States)

2011-01-13

logo, Direct FuelCell and “DFC” are all registered trademarks (®) of FuelCell Energy, Inc. Applications •On-site self generation of combined heat... of FuelCell Energy, Inc. Fuels Resources for DFC • Natural Gas and LNG • Propane • Biogas (by Anaerobicnaerobic Digestion) - Municipal Waste...FUEL RESOURCES z NATURAL GAS z PROPANE z DFC H2 (50-60%) z ETHANOL zWASTE METHANE z BIOGAS z COAL GAS Diversity of Fuels plus High Efficiency
Analyzing Vehicle Fuel Saving Opportunities through Intelligent Driver Feedback

Energy Technology Data Exchange (ETDEWEB)

Gonder, J.; Earleywine, M.; Sparks, W.

2012-06-01

Driving style changes, e.g., improving driver efficiency and motivating driver behavior changes, could deliver significant petroleum savings. This project examines eliminating stop-and-go driving and unnecessary idling, and also adjusting acceleration rates and cruising speeds to ideal levels to quantify fuel savings. Such extreme adjustments can result in dramatic fuel savings of over 30%, but would in reality only be achievable through automated control of vehicles and traffic flow. In real-world driving, efficient driving behaviors could reduce fuel use by 20% on aggressively driven cycles and by 5-10% on more moderately driven trips. A literature survey was conducted of driver behavior influences, and pertinent factors from on-road experiments with different driving styles were observed. This effort highlighted important driver influences such as surrounding vehicle behavior, anxiety over trying to get somewhere quickly, and the power/torque available from the vehicle. Existing feedback approaches often deliver efficiency information and instruction. Three recommendations for maximizing fuel savings from potential drive cycle improvement are: (1) leveraging applications with enhanced incentives, (2) using an approach that is easy and widely deployable to motivate drivers, and (3) utilizing connected vehicle and automation technologies to achieve large and widespread efficiency improvements.
40 CFR 600.006-87 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

..., motor controller, battery configuration, or other components performed within 2,000 miles prior to fuel... fuel economy vehicles. 600.006-87 Section 600.006-87 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel...
40 CFR 600.006-08 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

... controller, battery configuration, or other components performed within 2,000 miles prior to fuel economy... fuel economy vehicles. 600.006-08 Section 600.006-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel...
Gas detection for alternate-fuel vehicle facilities.

Science.gov (United States)

Ferree, Steve

2003-05-01

Alternative fuel vehicles' safety is driven by local, state, and federal regulations in which fleet owners in key metropolitan [table: see text] areas convert much of their fleet to cleaner-burning fuels. Various alternative fuels are available to meet this requirement, each with its own advantages and requirements. This conversion to alternative fuels leads to special requirements for safety monitoring in the maintenance facilities and refueling stations. A comprehensive gas and flame monitoring system needs to meet the needs of both the user and the local fire marshal.

Landfill Gas Conversion to LNG and LCO{sub 2}. Phase II Final Report for January 25, 1999 - April 30, 2000

Energy Technology Data Exchange (ETDEWEB)

Brown, W. R.; Cook, W. J.; Siwajek, L. A.

2000-10-20

This report summarizes work on the development of a process to produce LNG (liquefied methane) for heavy vehicle use from landfill gas (LFG) using Acrion's CO{sub 2} wash process for contaminant removal and CO{sub 2} recovery.
49 CFR 536.10 - Treatment of dual-fuel and alternative fuel vehicles-consistency with 49 CFR part 538.

Science.gov (United States)

2010-10-01

... vehicles-consistency with 49 CFR part 538. 536.10 Section 536.10 Transportation Other Regulations Relating... vehicles—consistency with 49 CFR part 538. (a) Statutory alternative fuel and dual-fuel vehicle fuel... economy in a particular compliance category by more than the limits set forth in 49 U.S.C. 32906(a), the...
Emissions from Diesel and Gasoline Vehicles Fuelled by Fischer-Tropsch Fuels and Similar Fuels

DEFF Research Database (Denmark)

Larsen, Ulrik; Lundorff, Peter; Ivarsson, Anders

2007-01-01

The described investigation was carried out under the umbrella of IEA Advanced Motor Fuels Agreement. The purpose was to evaluate the emissions of carbon monoxide (CO), unburned hydrocarbons (HC), nitrogen oxides (NOx), particulate matter (PM) and polycyclic aromatic hydrocarbons (PAH) from...... vehicles fuelled by Fischer Tropsch (FT) based diesel and gasoline fuel, compared to the emissions from ordinary diesel and gasoline. The comparison for diesel fuels was based on a literature review, whereas the gasoline comparison had to be based on our own experiments, since almost no references were...... found in this field. In this context measurement according to the Federal Test Procedure (FTP) and the New European Driving Cycle (NEDC) were carried out on a chassis dynamometer with a directly injected gasoline vehicle. Experiments were carried out with a reference fuel, a fuel based 70% on FT...
Introduction to the marine transportation of bulk LNG and the design of LNG carriers

Energy Technology Data Exchange (ETDEWEB)

Wilson, J J

1974-03-01

The marine transportation of bulk LNG is expected to expand considerably in the near future to help supply the continuous and growing demand for energy predicted for the U.S., Japan, and Western Europe. The number of new LNG tankers required to provide for these markets is estimated to be at least 50 new 4.4 million ft/sup 3/ tankers by 1980. The standard LNG tanker size is expected to increase to 7.06 million ft/sup 3/ within 5 yr. In selecting a particular tanker system, prospective ship-owners may have to consider such factors as national and international subsidies, shipyard limitations, and the trend to build certain specialized tanker components in areas other than in the shipyard. This work separation could help reduce tanker construction cost and time--especially important when several ships are to be constructed. Containment techniques available for construction of the cargo tanks include the self-supporting and the integrated designs, with the most economical provided by systems carrying LNG as a bulk cargo slightly subcooled below its boiling temperature at near-atmospheric pressure. All designs must fulfill the requirements for maintaining the approved temperature over the entire hull structure, preventing excess heat leaks into the cargo, providing tight liquid containment of the cargo, controlling the conditions inside and outside, and providing the proper facilities for safe loading and unloading. Materials of construction range from a combination of various grades of mild steel for the hull to the highest grades of aluminum alloys and nickel steels for the tank areas. Insulation includes polyurethane foam, silicon-coated perlite, and balsa wood used with fiberglass, polyurethane foam, or mineral wool. The insulation materials and arrangement must be waterproof, fire-resistant, and suitable to withstand the forces imposed on them. Finally, the tankers must include the proper equipment for LNG handling, pumping, and boiloff control.
Technology watch of fuel cells for vehicles in 2012; Teknikbevakning av braensleceller foer fordon 2012

Energy Technology Data Exchange (ETDEWEB)

Pohl, Hans

2013-03-15

The report presents results from an international survey covering the status and development of tractionary fuel cells. Interviews, study visits, reports, journals, media coverage and participation in IEA Advanced Fuel Cells Annex 26 have served as main sources of information. The development in Korea has been devoted particular attention this period. The report covers the development during the second part of 2011 and the whole 2012. The transport sector must change to provide mobility for people and goods in a long-term sustainable way. Fuel cell technology offers an important opportunity for the vehicle manufacturer and the vehicle user to maintain the same level of performance, comfort and versatility without compromising the sustainability requirements. Fuel cell vehicles typically use polymer electrolyte fuel cells (PEFC) and pressurized hydrogen. They also use tractionary batteries for about the same reasons as other hybrid electric vehicles. For commercial vehicles fuel cells are developed for the production of auxiliary power, to be used when the vehicles are parked, for example. Until 2015, Hyundai aims at making up to 1,000 fuel cell vehicles. After 2015 the plan is for several thousand every year. Until 2025, Hyundai aims at a total delivery of more than 100,000 fuel cell vehicles and the technology is then expected to be fully competitive. A roadmap shows that Korea until 2015 has established 43 and until 2030, a total of 500 hydrogen refuelling stations are indicated. The Skaane Region has carried out the first Swedish procurement of fuel cell vehicles. Two Hyundai iX35 FCEV were purchased for delivery 2013. In addition, the city of Copenhagen has purchased 15 such vehicles. During the next few years three hydrogen refuelling stations will be established in the Copenhagen area. January 2012, the California Air Resources Board decided the new set of regulations Advanced Clean Cars. It comprises three parts; tailpipe emissions and greenhouse gases, Zero
Direct-hydrogen-fueled proton-exchange-membrane fuel cell system for transportation applications. Hydrogen vehicle safety report

Energy Technology Data Exchange (ETDEWEB)

Thomas, C.E. [Directed Technologies, Inc., Arlington, VA (United States)

1997-05-01

This report reviews the safety characteristics of hydrogen as an energy carrier for a fuel cell vehicle (FCV), with emphasis on high pressure gaseous hydrogen onboard storage. The authors consider normal operation of the vehicle in addition to refueling, collisions, operation in tunnels, and storage in garages. They identify the most likely risks and failure modes leading to hazardous conditions, and provide potential countermeasures in the vehicle design to prevent or substantially reduce the consequences of each plausible failure mode. They then compare the risks of hydrogen with those of more common motor vehicle fuels including gasoline, propane, and natural gas.
Safety and environmental aspects in LNG carrier design

International Nuclear Information System (INIS)

Takashi Yoneyama

1997-01-01

'Safety and Reliability' has been and will continue to be a key phr ase in marine transportation of LNG. Mitsui Engineering and Shipbuilding Co.,Ltd. has utilized its all expertise and state of art technologies to realize this objective, resulting in exceptionally successful operations of LNG carrier built by the Co. In line with growing global concern about environmental issues, we need to pay more attention to the environmental aspects of the design and construction of LNG carriers. Accordingly, in this paper, we present some topics related safety and environmental concerns which need to be taken into consideration in LNG carriers design and construction. (Author). 7 figs
Safety and environmental aspects in LNG carrier design

Energy Technology Data Exchange (ETDEWEB)

Yoneyama, Takashi [Mitsui Shipbuilding and Engineering Co. Ltd., Tokyo (Japan)

1997-06-01

`Safety and Reliability` has been and will continue to be a key phr ase in marine transportation of LNG. Mitsui Engineering and Shipbuilding Co.,Ltd. has utilized its all expertise and state of art technologies to realize this objective, resulting in exceptionally successful operations of LNG carrier built by the Co. In line with growing global concern about environmental issues, we need to pay more attention to the environmental aspects of the design and construction of LNG carriers. Accordingly, in this paper, we present some topics related safety and environmental concerns which need to be taken into consideration in LNG carriers design and construction. (Author). 7 figs.
Effect of interactions between vehicles and pedestrians on fuel consumption and emissions

Science.gov (United States)

Li, Xiang; Sun, Jian-Qiao

2014-12-01

This paper presents a study of variations of fuel consumption and emissions of vehicles due to random street crossings of pedestrians. The pedestrian and vehicle movement models as well as the interaction model between the two entities are presented. Extensive numerical simulations of single and multiple cars are carried out to investigate the traffic flow rate, vehicle average speed, fuel consumption, CO, HC and NOx emissions. Generally more noncompliant road-crossings of pedestrians lead to higher level of fuel consumptions and emissions of vehicles, and the traffic situation can be improved by imposing higher vehicle speed limit to some extent. Different traffic characteristics in low and high vehicle density regions are studied. The traffic flow is more influenced by crossing pedestrians in the low vehicle density region, while in the high vehicle density region, the interactions among vehicles dominate. The main contribution of this paper lies in the qualitative analysis of the impact of the interactions between pedestrians and vehicles on the traffic, its energy economy and emissions.
Alternative fuels for vehicles fleet demonstration program. Final report, volume 2: Appendices

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The Alternative Fuels for Vehicles Fleet Demonstration Program (AFV-FDP) was a multiyear effort to collect technical data for use in determining the costs and benefits of alternative-fuel vehicles (AFVs) in typical applications in New York State. This report, Volume 2, includes 13 appendices to Volume 1 that expand upon issues raised therein. Volume 1 provides: (1) Information about the purpose and scope of the AFV-FDP; (2) A summary of AFV-FDP findings organized on the basis of vehicle type and fuel type; (3) A short review of the status of AFV technology development, including examples of companies in the State that are active in developing AFVs and AFV components; and (4) A brief overview of the status of AFV deployment in the State. Volume 3 provides expanded reporting of AFV-FDP technical details, including the complete texts of the brochure Garage Guidelines for Alternative Fuels and the technical report Fleet Experience Survey Report, plus an extensive glossary of AFV terminology. The appendices cover a wide range of issues including: emissions regulations in New York State; production and health effects of ozone; vehicle emissions and control systems; emissions from heavy-duty engines; reformulated gasoline; greenhouse gases; production and characteristics of alternative fuels; the Energy Policy Act of 1992; the Clean Fuel Fleet Program; garage design guidelines for alternative fuels; surveys of fleet managers using alternative fuels; taxes on conventional and alternative fuels; and zero-emission vehicle technology.
Coordination of ministerial actions regarding the use of liquefied natural gas as marine fuel. Progress report at 31 August 2014

International Nuclear Information System (INIS)

Maler, Philippe; Erhardt, Jean-Bernard; Ourliac, Jean-Paul

2014-09-01

This report is the second of a series dealing with the coordination of ministerial actions in favor of the use of liquefied natural gas (LNG) as marine fuel. Tougher sulfur oxides pollution regulations will lead to the progressive abandonment of heavy fuels in maritime propulsion. LNG can meet the future environmental imperatives but its introduction as marine fuel implies important naval and infrastructure investments. This report presents, first, a summary of the report's recommendations and the aim of this coordination study, and, then, treats more thoroughly of the different coordination aspects: 1 - Progresses made by the coordination mission between February 2013 and July 2014 (multiplicity of intervening actors and communication problems); 2 - situation and perspectives of member countries policy having an impact on marine bunker fuels (fuel substitution directive project, marine CO 2 pollution monitoring project, EU's air quality policy and ships emissions, energy and environment policies by 2030, maritime transport and environmental pollution); 3 - rules and standards for LNG-fueled ships supply and exploitation (LNG-fueled ships, fuel supply, regulations, personnel training, European framework); 4 - ships and LNG facilities financing (European programs, financing); 5 - pilot project's situation (Dunkerque harbour, Brittany Ferries project, Montoir and Fos LNG terminals, big and decentralized harbours, Ministry's actions, French projects with European participation)
The demand for clean-fuel vehicles by Dutch local authorities. A stated choice analysis

Energy Technology Data Exchange (ETDEWEB)

Hagen, P.

2012-08-15

Previous research showed that the era of cheap fossil fuels is over. Also, 23% of the worldwide emission of CO2 is produced by road transport. These problems demand a change in the propulsion of vehicles. Because the diffusion of clean-fuel vehicles is not happening at this moment, something has to change. Rogers' diffusion of innovation theory is used to state that a critical mass of vehicles is needed to stimulate the diffusion of these vehicles. Due to public procurement Dutch local authorities (DLA's) can help stimulating this diffusion. Unfortunately these DLA's are not purchasing clean-fuel vehicles yet. To gain insight in what is hampering the diffusion of these vehicles by DLA's, a discrete choice experiment was created about the preferences by these DLA's. Six vehicle attributes were used to describe each vehicle. The results showed that the initial purchase price and the amount of local emission were experienced as the most important attributes by DLA's, where initial purchase price has a negative influence and local emission a positive influence in the choice for a new vehicle. Next, fuel price, range and availability of the fuel were found evenly important. Fuel price had a negative influence and both range and availability of fuel had a positive influence on the choice for a new vehicle. Finally, time to refuel/recharge was found least important and also negatively influencing the choice.
49 CFR 193.2181 - Impoundment capacity: LNG storage tanks.

Science.gov (United States)

2010-10-01

... LIQUEFIED NATURAL GAS FACILITIES: FEDERAL SAFETY STANDARDS Design Impoundment Design and Capacity § 193.2181 Impoundment capacity: LNG storage tanks. Each impounding system serving an LNG storage tank must have a... 49 Transportation 3 2010-10-01 2010-10-01 false Impoundment capacity: LNG storage tanks. 193.2181...
77 FR 43589 - Freeport LNG Development, L.P., Freeport LNG Expansion, L.P., FLNG Liquefaction LLC; Supplemental...

Science.gov (United States)

2012-07-25

... addition, a second ship berthing area, third LNG storage tank, and additional LNG vaporization and natural... 7.3 7.3 Appurtenant Facilities beyond Terminal Site and Pretreatment 0.1 0.1 0.2 Facility site and... issues that we think deserve attention based on a preliminary review of the planned facilities and the...
Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

Energy Technology Data Exchange (ETDEWEB)

Nielsen, L.H.; Joergensen, K.

2000-04-01

The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore to illustrate the potential synergistic interplay between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalised electricity market are analysed. The project focuses on battery electric vehicles and fuel cell vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and for the conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport vehicles. Focus is put on the Danish fleet of passenger cars and delivery vans. The scenario analysis includes assumptions on market potential developments and market penetration for the alternative vehicles. Vehicle replacement rates in the Danish transport fleet and the size of fleet development are based on data from The Danish Road Directorate. The electricity supply system development assumed is based on the Danish energy plan, Energy 21, The Plan scenario. The time horizon of the analysis is year 2030. Results from the scenario analysis include the time scales involved for the potential transition towards electricity based vehicles, the fleet composition development, the associated developments in transport fuel consumption and fuel substitution, and the potential CO{sub 2}-emission reduction achievable in the overall transport and power supply system. Detailed model simulations, on an hourly basis, have furthermore been carried out for year 2005 that address potential electricity purchase options for electric vehicles in the context of a liberalised electricity market
Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

International Nuclear Information System (INIS)

Nielsen, L.H.; Joergensen, K.

2000-04-01

The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore to illustrate the potential synergistic interplay between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalised electricity market are analysed. The project focuses on battery electric vehicles and fuel cell vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and for the conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport vehicles. Focus is put on the Danish fleet of passenger cars and delivery vans. The scenario analysis includes assumptions on market potential developments and market penetration for the alternative vehicles. Vehicle replacement rates in the Danish transport fleet and the size of fleet development are based on data from The Danish Road Directorate. The electricity supply system development assumed is based on the Danish energy plan, Energy 21, The Plan scenario. The time horizon of the analysis is year 2030. Results from the scenario analysis include the time scales involved for the potential transition towards electricity based vehicles, the fleet composition development, the associated developments in transport fuel consumption and fuel substitution, and the potential CO 2 -emission reduction achievable in the overall transport and power supply system. Detailed model simulations, on an hourly basis, have furthermore been carried out for year 2005 that address potential electricity purchase options for electric vehicles in the context of a liberalised electricity market. The
Fuel conservation and GHG (Greenhouse gas) emissions mitigation scenarios for China’s passenger vehicle fleet

International Nuclear Information System (INIS)

Hao, Han; Wang, Hewu; Ouyang, Minggao

2011-01-01

Passenger vehicles are the main consumers of gasoline in China. We established a bottom-up model which focuses on the simulation of energy consumptions and greenhouse gas (GHG) emissions growth by China’s passenger vehicle fleet. The fuel conservation and GHG emissions mitigation effects of five measures including constraining vehicle registration, reducing vehicle travel, strengthening fuel consumption rate (FCR) limits, vehicle downsizing and promoting electric vehicle (EV) penetration were evaluated. Based on the combination of these measures, the fuel conservation and GHG emissions mitigation scenarios for China’s passenger vehicle fleet were analyzed. Under reference scenario with no measures implemented, the fuel consumptions and life cycle GHG emissions will reach 520 million tons of oil equivalent (Mtoe) and 2.15 billion tons in 2050, about 8.1 times the level in 2010. However, substantial fuel conservation can be achieved by implementing the measures. By implementing all five measures together, the fuel consumption will reach 138 Mtoe in 2030 and decrease to 126 Mtoe in 2050, which is only 37.1% and 24.3% of the consumption under reference scenario. Similar potential lies in GHG mitigation. The results and scenarios provided references for the Chinese government’s policy-making. -- Highlights: ► We established a bottom-up model to simulate the fuel consumptions and GHG (Greenhouse gas) emissions growth by China’s passenger vehicle fleet. ► Five measures including constraining vehicle registration, reducing vehicle travel, improving fuel efficiency, vehicle downsizing and promoting EV penetration were evaluated. ► The fuel conservation and GHG emissions mitigation scenarios for China’s passenger vehicle fleet were provided as references for policy-making.
Life cycle assessment for next generating vehicles. Feasibility study of alternative fuel vehicles and electric vehicles; Jisedai jidosha no life cycle assessment. Daitai nenryo jidosha oyobi denki jidosha no feasibility study

Energy Technology Data Exchange (ETDEWEB)

Hanyu, T; Iida, N [Keio University, Tokyo (Japan)

1997-10-01

To show environmental assessment of introduction of substitute fuel vehicles is important information to formulate the future vehicles policy. Life cycle assessment (LCA) is put forward to simulate such potential, allows us to state the reduction environmental impacts of substitute vehicles on their total life cycle. The purpose of this study is assessment and analysis of the life cycle CO2 emission for substitute fuel vehicles, such as, alternative fuel vehicles, electric vehicles, and hybrid electric vehicles. 8 refs., 9 figs., 3 tabs.
Pump-to-Wheels Methane Emissions from the Heavy-Duty Transportation Sector.

Science.gov (United States)

Clark, Nigel N; McKain, David L; Johnson, Derek R; Wayne, W Scott; Li, Hailin; Akkerman, Vyacheslav; Sandoval, Cesar; Covington, April N; Mongold, Ronald A; Hailer, John T; Ugarte, Orlando J

2017-01-17

Pump-to-wheels (PTW) methane emissions from the heavy-duty (HD) transportation sector, which have climate change implications, are poorly documented. In this study, methane emissions from HD natural gas fueled vehicles and the compressed natural gas (CNG) and liquefied natural gas (LNG) fueling stations that serve them were characterized. A novel measurement system was developed to quantify methane leaks and losses. Engine related emissions were characterized from twenty-two natural gas fueled transit buses, refuse trucks, and over-the-road (OTR) tractors. Losses from six LNG and eight CNG stations were characterized during compression, fuel delivery, storage, and from leaks. Cryogenic boil-off pressure rise and pressure control venting from LNG storage tanks were characterized using theoretical and empirical modeling. Field and laboratory observations of LNG storage tanks were used for model development and evaluation. PTW emissions were combined with a specific scenario to view emissions as a percent of throughput. Vehicle tailpipe and crankcase emissions were the highest sources of methane. Data from this research are being applied by the authors to develop models to forecast methane emissions from the future HD transportation sector.
US Department of Energy Hybrid Electric Vehicle Battery and Fuel Economy Testing

Science.gov (United States)

Karner, Donald; Francfort, James

The advanced vehicle testing activity (AVTA), part of the US Department of Energy's FreedomCAR and Vehicle Technologies Program, has conducted testing of advanced technology vehicles since August 1995 in support of the AVTA goal to provide benchmark data for technology modelling, and research and development programs. The AVTA has tested over 200 advanced technology vehicles including full-size electric vehicles, urban electric vehicles, neighborhood electric vehicles, and internal combustion engine vehicles powered by hydrogen. Currently, the AVTA is conducting a significant evaluation of hybrid electric vehicles (HEVs) produced by major automotive manufacturers. The results are posted on the AVTA web page maintained by the Idaho National Laboratory. Through the course of this testing, the fuel economy of HEV fleets has been monitored and analyzed to determine the 'real world' performance of their hybrid energy systems, particularly the battery. The initial fuel economy of these vehicles has typically been less than that determined by the manufacturer and also varies significantly with environmental conditions. Nevertheless, the fuel economy and, therefore, battery performance, has remained stable over the life of a given vehicle (160 000 miles).

Thermodynamic analysis of a novel dual-loop organic Rankine cycle for engine waste heat and LNG cold

International Nuclear Information System (INIS)

Sung, Taehong; Kim, Kyung Chun

2016-01-01

Highlights: • A novel dual ORC system is designed for engine waste heat and LNG cold. • Exhaust gas and jacket cooling water are considered as heat sources. • LNG and boil-off gas are considered as heat sinks. • ORC loops are optimized to produce the maximum net work output. - Abstract: The marine sector produces a large portion of total air pollution, so the emissions of the engines used must be improved. This can be achieved using a new eco-friendly engine and waste-heat recovery system. A dual-fuel (DF) engine has been introduced for LNG carriers that is eco-friendly and has high thermal efficiency since it uses natural gas as fuel. The thermal efficiency could be further improved with the organic Rankine cycle (ORC). A novel dual-loop ORC system was designed for DF engines. The upper ORC loop recovers waste heat from the exhaust gas, and the bottom ORC loop recovers waste heat from the jacket cooling water and LNG cold. Both ORC loops were optimized to produce the maximum net work output. The optimum simple dual-loop ORC with n-pentane and R125 as working fluids produces an additional power output of 729.1 kW, which is 4.15% of the original engine output. Further system improvement studies were conducted using a recuperator and preheater, and the feasibility of using boil-off gas as a heat sink was analyzed. Optimization of the system configuration revealed that the preheater and recuperator with n-pentane and R125 as working fluids increase the maximum net work output by 906.4 kW, which is 5.17% of the original engine output.
LNG in eastern Canada and New England : market update

International Nuclear Information System (INIS)

Schlesinger, B.

2005-01-01

This presentation provided an overview of the gas markets in North America and discussed the rationale for developing the liquefied natural gas (LNG) market with reference to competitive issues, challenges and global dimensions. LNG is expected to play a greater role in North American gas supplies and markets due to the decrease in conventional natural gas production in North America and the increase in demand for energy. It is expected that the overall share of the LNG gas market will increase in 2002. The construction of at least 15 new LNG receiving terminals has been proposed for location in the U.S., Canada, and Mexico, with most being located along the Gulf Coast. A novel offshore LNG receiving concept involving offshore gas pipelines and on-board-ship regasification was also discussed. As trading of LNG increases in the Atlantic, markets in eastern United States and Canada will benefit from improved gas supplies. Pricing patterns are also expected to change. It was noted that the increased energy demand will enable Arctic gas supplies to enter markets. As such, Arctic gas pipelines will enter service in the next decade and Alberta's importance as a hub will grow. It was also noted that Arctic gas will not have a significant influence on reducing LNG import volumes. figs
Project financing knits parts of costly LNG supply chain

International Nuclear Information System (INIS)

Minyard, R.J.; Strode, M.O.

1997-01-01

The supply and distribution infrastructure of an LNG project requires project sponsors and LNG buyers to make large, interdependent capital investments. For a grassroots project, substantial investments may be necessary for each link in the supply chain: field development; liquefaction plant and storage; ports and utilities; ships; receiving terminal and related facilities; and end-user facilities such as power stations or a gas distribution network. The huge sums required for these projects make their finance ability critical to implementation. Lenders have become increasingly comfortable with LNG as a business and now have achieved a better understanding of the risks associated with it. Raising debt financing for many future LNG projects, however, will present new and increasingly difficult challenges. The challenge of financing these projects will be formidable: political instability, economic uncertainty, and local currency volatility will have to be recognized and mitigated. Described here is the evolution of financing LNG projects, including the Rasgas LNG project financing which broke new ground in this area. The challenges that lie ahead for sponsors seeking to finance future projects selling LNG to emerging markets are also discussed. And the views of leading experts from the field of project finance, specifically solicited for this article, address major issues that must be resolved for successful financing of these projects
LNG : its potential impact on North American markets

International Nuclear Information System (INIS)

Schlesinger, B.

2003-01-01

Liquefied natural gas (LNG) is expected to play a greater role in North American gas supplies and markets due to the decrease in conventional natural gas production in North America accompanied by an increase in demand for energy. It is expected that the overall share of the LNG gas market will rise from about 1.4 per cent in 2002 to more than 5 per cent by 2020, and potentially up to 15 per cent by that year. The construction of at least 15 new LNG receiving terminals has been proposed for location in the U.S., Canada, and Mexico. In addition, El Paso has proposed a novel offshore LNG receiving concept involving offshore gas pipelines and on-board-ship regasification. As trading of LNG increases in the Atlantic, markets in eastern United States and Canada will benefit from improved gas supplies, but pricing patterns are expected to change. Basis differentials along the Atlantic coastline will probably diminish, potentially reducing the value of Sable Island gas and the pipeline system that runs north to south along the eastern coast of North America. It was noted that Middle Eastern suppliers of LNG will play an important potential role in North American markets. 19 figs
16 CFR 309.15 - Posting of non-liquid alternative vehicle fuel rating.

Science.gov (United States)

2010-01-01

... rating. (a) If you are a retailer who offers for sale or sells non-liquid alternative vehicle fuel (other... fuel. If you are a retailer who offers for sale or sells electricity to consumers through an electric... vehicle fuel dispensing system, either by letter or on the delivery ticket or other paper, or by a...
40 CFR 80.552 - What compliance options are available to motor vehicle diesel fuel small refiners?

Science.gov (United States)

2010-07-01

... to motor vehicle diesel fuel small refiners? 80.552 Section 80.552 Protection of Environment... Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Small Refiner Hardship Provisions § 80.552 What compliance options are available to motor vehicle diesel fuel...
A Range-Based Vehicle Life Cycle Assessment Incorporating Variability in the Environmental Assessment of Different Vehicle Technologies and Fuels

Directory of Open Access Journals (Sweden)

Maarten Messagie

2014-03-01

Full Text Available How to compare the environmental performance of different vehicle technologies? Vehicles with lower tailpipe emissions are perceived as cleaner. However, does it make sense to look only to tailpipe emissions? Limiting the comparison only to these emissions denies the fact that there are emissions involved during the production of a fuel and this approach gives too much advantage to zero-tailpipe vehicles like battery electric vehicles (BEV and fuel cell electric vehicle (FCEV. Would it be enough to combine fuel production and tailpipe emissions? Especially when comparing the environmental performance of alternative vehicle technologies, the emissions during production of the specific components and their appropriate end-of-life treatment processes should also be taken into account. Therefore, the complete life cycle of the vehicle should be included in order to avoid problem shifting from one life stage to another. In this article, a full life cycle assessment (LCA of petrol, diesel, fuel cell electric (FCEV, compressed natural gas (CNG, liquefied petroleum gas (LPG, hybrid electric, battery electric (BEV, bio-diesel and bio-ethanol vehicles has been performed. The aim of the manuscript is to investigate the impact of the different vehicle technologies on the environment and to develop a range-based modeling system that enables a more robust interpretation of the LCA results for a group of vehicles. Results are shown for climate change, respiratory effects, acidification and mineral extraction damage of the different vehicle technologies. A broad range of results is obtained due to the variability within the car market. It is concluded that it is essential to take into account the influence of all the vehicle parameters on the LCA results.
Liquefied natural gas (LNG) market and Australia

Science.gov (United States)

Alam, Firoz; Alam, Quamrul; Reza, Suman; Khurshid-ul-Alam, S. M.; Saleque, Khondkar; Ahsan, Saifuddin

2017-06-01

As low carbon-emitting fossil fuel, the natural gas is mainly used for power generation and industrial applications. It is also used for heating and cooling in commercial and residential buildings as well as in transport industry. Although the natural gas reaches the end-user mainly through pipelines (if gas is available locally), the liquefied form is the most viable alternative to transport natural gas from far away location to the end user. The economic progress in Asia and other parts of the world creates huge demand for energy (oil, gas and coal). As low carbon-emitting fuel, the demand for gas especially in liquefied form is progressively rising. Having 7th largest shale gas reserve (437 trillion cubic feet recoverable), Australia has become one of the world's major natural gas producers and exporters and is expected to continue a dominating role in the world gas market in foreseeable future. This paper reviews Australia's current gas reserve, industries, markets and LNG production capabilities.
Coordination of ministerial actions regarding the use of liquefied natural gas as marine fuel. A challenge to take up collectively

International Nuclear Information System (INIS)

Jouffray, Jean-Francois; Erhardt, Jean-Bernard; Allais, Vincent; Ourliac, Jean-Paul

2013-02-01

This report is the first of a series dealing with the coordination of ministerial actions in favor of the use of liquefied natural gas (LNG) as marine fuel. Tougher sulfur oxides pollution regulations will lead to the progressive abandonment of heavy fuels in maritime propulsion. LNG can meet the future environmental imperatives but its introduction as marine fuel implies important naval and infrastructure investments. This report presents, first, a summary of the report's recommendations and the aim of this coordination study, and, then, treats more thoroughly of the different coordination aspects: 1 - ship fuels; 2 - LNG's advantages; 3 - the necessary adaptations in France for LNG development as marine fuel (infrastructures, regulation, existing examples, exemptions, European policies); 4 - economical actors involvement, industrial challenges, pilot projects, communication, investments financing and actors coordination
Calculating the price trajectory of adoption of fuel cell vehicles

Energy Technology Data Exchange (ETDEWEB)

Adamson, K.-A. [Technical University of Berlin (Germany). Fuel Cell and Hydrogen Research Centre

2005-03-01

How do you model consumer behaviour for disruptive technologies? Technologies that potentially have no antecedents and that, by their very definition, change consumer behaviour patterns? This paper outlines a methodology and results employed during a study to model the consumer willingness to pay for fuel cell vehicles, a potential disruptive innovation (DI). The first part of the study provides a short overview on DI highlighting why the fuel cell family of technologies may represent an upcoming DI. From the post ante study of successful historical disruptive innovations a number of initial rules of adoption' can be sketched. Further narrowing of the focus on economic reasons for adoption provides a framework for which the willingness to pay for the new disruptive technology, such as, here, fuel cell vehicles, can be analysed during different phases of the market. This economic framework is then applied to the potential future market of fuel cell vehicles using information from a model that was built from vehicles during the build years 1994-2002 in the subcompact, compact and luxury class. The results presented in this paper concentrate on the subcompact and compact class of vehicle and supersede the initial results previously published. Finally, there is a short discussion on different pathways that this can be taken forward and used to help in policy decisions. (author)
Opportunities for PEM fuel cell commercialization : fuel cell electric vehicle demonstration in Shanghai

Energy Technology Data Exchange (ETDEWEB)

Ma, Z.F. [Shanghai Jiao Tong Univ., Shanghai (China). Dept. of Chemical Engineering

2006-07-01

The research and development activities devoted to the development of the proton exchange membrane fuel cell (PEMFC) were discussed with reference to its application in the fuel cell electric vehicle (FCEV). In the past decade, PEMFC technology has been successfully applied in both the automobile and residential sector worldwide. In China, more than one billion RMB yuan has been granted by the Chinese government to develop PEM fuel cell technology over the past 5 years, particularly for commercialization of the fuel cell electric vehicle (FCEV). The City of Shanghai has played a significant role in the FCEV demonstration with involvement by Shanghai Auto Industrial Company (SAIC), Tongji University, Shanghai Jiaotong University, and Shanghai Shenli High Tech Co. Ltd. These participants were involved in the development and integration of the following components into the FCEV: fuel cell engines, batteries, FCEV electric control systems, and primary materials for the fuel cell stack. During the course of the next five year-plan (2006-2010), Shanghai will promote the commercialization of FCEV. More than one thousand FCEVs will be manufactured and an FCEV fleet will be in operation throughout Shanghai City by 2010.
40 CFR 80.520 - What are the standards and dye requirements for motor vehicle diesel fuel?

Science.gov (United States)

2010-07-01

... requirements for motor vehicle diesel fuel? 80.520 Section 80.520 Protection of Environment ENVIRONMENTAL... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.520 What are the standards and dye requirements for motor vehicle diesel...
Clean Cities Guide to Alternative Fuel and Advanced Medium- and Heavy-Duty Vehicles

Energy Technology Data Exchange (ETDEWEB)

None

2013-08-01

Today's fleets are increasingly interested in medium-duty and heavy-duty vehicles that use alternative fuels or advanced technologies that can help reduce operating costs, meet emissions requirements, improve fleet sustainability, and support U.S. energy independence. Vehicle and engine manufacturers are responding to this interest with a wide range of options across a steadily growing number of vehicle applications. This guide provides an overview of alternative fuel power systems--including engines, microturbines, electric motors, and fuel cells--and hybrid propulsion systems. The guide also offers a list of individual medium- and heavy-duty vehicle models listed by application, along with associated manufacturer contact information, fuel type(s), power source(s), and related information.
Light-Duty Vehicle CO2 and Fuel Economy Trends

Science.gov (United States)

This report provides data on the fuel economy, carbon dioxide (CO2) emissions, and technology trends of new light-duty vehicles (cars, minivans, sport utility vehicles, and pickup trucks) for model years 1975 to present in the United States.
Fuel consumption from vehicles of China until 2030 in energy scenarios

International Nuclear Information System (INIS)

Zhang Qingyu; Tian Weili; Zheng Yingyue; Zhang Lili

2010-01-01

Estimation of fuel (gasoline and diesel) consumption for vehicles in China under different long-term energy policy scenarios is presented here. The fuel economy of different vehicle types is subject to variation of government regulations; hence the fuel consumption of passenger cars (PCs), light trucks (Lts), heavy trucks (Hts), buses and motor cycles (MCs) are calculated with respect to (i) the number of vehicles, (ii) distance traveled, and (iii) fuel economy. On the other hand, the consumption rate of alternative energy sources (i.e. ethanol, methanol, biomass-diesel and CNG) is not evaluated here. The number of vehicles is evaluated using the economic elastic coefficient method, relating to per capita gross domestic product (GDP) from 1997 to 2007. The Long-range Energy Alternatives Planning (LEAP) system software is employed to develop a simple model to project fuel consumption in China until 2030 under these scenarios. Three energy consumption decrease scenarios are designed to estimate the reduction of fuel consumption: (i) 'business as usual' (BAU); (ii) 'advanced fuel economy' (AFE); and (iii) 'alternative energy replacement' (AER). It is shown that fuel consumption is predicted to reach 992.28 Mtoe (million tons oil equivalent) with the BAU scenario by 2030. In the AFE and AER scenarios, fuel consumption is predicted to be 734.68 and 600.36 Mtoe, respectively, by 2030. In the AER scenario, fuel consumption in 2030 will be reduced by 391.92 (39.50%) and 134.29 (18.28%) Mtoe in comparison to the BAU and AFE scenarios, respectively. In conclusion, our models indicate that the energy conservation policies introduced by governmental institutions are potentially viable, as long as they are effectively implemented.
An investigation on the fuel savings potential of hybrid hydraulic refuse collection vehicles.

Science.gov (United States)

Bender, Frank A; Bosse, Thomas; Sawodny, Oliver

2014-09-01

Refuse trucks play an important role in the waste collection process. Due to their typical driving cycle, these vehicles are characterized by large fuel consumption, which strongly affects the overall waste disposal costs. Hybrid hydraulic refuse vehicles offer an interesting alternative to conventional diesel trucks, because they are able to recuperate, store and reuse braking energy. However, the expected fuel savings can vary strongly depending on the driving cycle and the operational mode. Therefore, in order to assess the possible fuel savings, a typical driving cycle was measured in a conventional vehicle run by the waste authority of the City of Stuttgart, and a dynamical model of the considered vehicle was built up. Based on the measured driving cycle and the vehicle model including the hybrid powertrain components, simulations for both the conventional and the hybrid vehicle were performed. Fuel consumption results that indicate savings of about 20% are presented and analyzed in order to evaluate the benefit of hybrid hydraulic vehicles used for refuse collection. Copyright © 2014 Elsevier Ltd. All rights reserved.
Desain Rantai Pasok Gas Alam Cair (LNG untuk Kebutuhan Pembangkit Listrik di Indonesia Bagian Timur

Directory of Open Access Journals (Sweden)

Made Arya Satya Dharma Putra

2017-01-01

Full Text Available Indonesia merupakan negara yang memiliki gas alam yang melimpah, namun kurangnya kesadaran masyarakat Indonesia untuk memanfaatkan gas tersebut untuk kebutuhan listrik di Indonesia yang sekarang sedang dalam krisis terutama di Indonesia Timur. Salah satu penyebab krisis tenaga listrik yang terjadi di Indonesia adalah tingginya nilai harga bahan bakar minyak, dimana High Speed Diesel Oil merupakan bahan bakar utama bagi pembangkit listrik di Indonesia. Gas alam cair atau Liquefied Natural Gas (LNG dapat menjadi solusi alternatif bahan bakar bagi pembangkit listrik di Indonesia.Studi kali ini bertujuan untuk pemanfaatan gas alam cair (LNG untuk kebutuhan pembangkit listrik di Indonesia Timur dengan menentukan pola distribusi LNG dengan menggunakan Blok Masela sebagai sumber LNG dan menggunakan kapal untuk mendistribusikannya. Terdapat 39 pembangkit yang tersebar di 4 pulau yaitu Maluku, Nusa Tenggara Barat, Nusa Tenggara Timur, dan Papua. Kapal yang digunakan untuk mendistribusikan terdapat 5 kapal dengan ukuran 2500 m3, 7500 m3, 10000 m3, 19500 m3, 23000 m3. Untuk mendapatkan rute distribusi, studi ini menggunakan metode Linear Programing dan dalam Vehicle Routing Problem. Hasil optimasi pada distribusi ini adalah rute dan kapal yang optimal / terbaik dengan biaya ekonomi yang minimal.Dari hasil penelitian ini pembangkit akan dibagi menjadi 5 cluster dimana terdapat 5 rute yang terpilih dengan menggunakan 6 kapal yaitu 5 kapal ukuran 2500 m3 dan 1 kapal dengan ukuran 7500m3. Biaya total yang diperlukan dalam mendistribusikan LNG sebesar US$ 111,863,119.15 untuk Opex dan US$ 283,967,000.00 untuk Capex. Hasil dari kajian ekonomi menunjukan bahwa margin penjualan yang terpilih adalah antara US$ 3.5 sampai US$ 3.9 dengan payback period selama 6.8 – 4.7 tahun tahun dari waktu operasi 20 tahun.
Predicting Light-Duty Vehicle Fuel Economy as a Function of Highway Speed

Energy Technology Data Exchange (ETDEWEB)

Thomas, John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hwang, Ho-Ling [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); West, Brian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Huff, Shean [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2013-04-08

The www.fueleconomy.gov website offers information such as window label fuel economy for city, highway, and combined driving for all U.S.-legal light-duty vehicles from 1984 to the present. The site is jointly maintained by the U.S. Department of Energy and the U.S. Environmental Protection Agency (EPA), and also offers a considerable amount of consumer information and advice pertaining to vehicle fuel economy and energy related issues. Included with advice pertaining to driving styles and habits is information concerning the trend that as highway cruising speed is increased, fuel economy will degrade. An effort was undertaken to quantify this conventional wisdom through analysis of dynamometer testing results for 74 vehicles at steady state speeds from 50 to 80 mph. Using this experimental data, several simple models were developed to predict individual vehicle fuel economy and its rate of change over the 50-80 mph speed range interval. The models presented require a minimal number of vehicle attributes. The simplest model requires only the EPA window label highway mpg value (based on the EPA specified estimation method for 2008 and beyond). The most complex of these simple model uses vehicle coast-down test coefficients (from testing prescribed by SAE Standard J2263) known as the vehicle Target Coefficients, and the raw fuel economy result from the federal highway test. Statistical comparisons of these models and discussions of their expected usefulness and limitations are offered.
The LNG industry - 2008

International Nuclear Information System (INIS)

2008-01-01

The average annual growth of the world primary energy consumption has been 2.2% over the last ten years, with the highest growth rate observed for 2004 (+4.7%). In 2007, world primary energy consumption registered a 2.4% increase, still exceeding the 10-year average but less than for the four previous years. As for the previous years, the Asia Pacific region shows the most important increase in volume for 2007, rising by 5% and accounting for two-third of the global growth (China alone accounts in 2007 for more than half of this global growth, as was already the case in 2005 and 2006). Over the last ten years, the world energy consumption rose from 8920 10 6 toe in 1998 to 11099 10 6 toe in 2007, a 24.4% overall increase. For the seventh year running, coal has increased its share of the overall energy market, up to 28.6%. It should be noted that nuclear power decreased by 2%, Germany and Japan accounting for more than 90% of this decline. The growth of natural gas consumption in 2007 (+3.1%) was higher than in 2006 (+2.4%). The US accounted for nearly half of the global increase. Strong growth was also observed in China (+19.9%), representing the second largest increment to world gas consumption. Inversely, the EU consumption decreased (-1.6%) for the second year in a row. The market share for natural gas remained stable in 2007 (23.8%) compared to 2006 (23.6%)(1). Estimates for the marketed production of natural gas in 2008(2) show a rise of about 3.4% over 2007. The share of LNG in the gas trade accounts for 27% of the total (excluding trade within the Former Soviet Union and United Arab Emirates). Details are given about: LNG contracts and trade, Contracts concluded in 2008, LNG imports - Sources of imports, Quantities received in 2008, LNG tankers, Ships delivered, Tanker distribution, Liquefaction plants, Re-gasification plants, Contracts in force in 2008, Spot and short term quantities received in 2008, Sea transportation routes, Liquefaction plants, Re
40 CFR 600.006-86 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

... fuel economy vehicles. 600.006-86 Section 600.006-86 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-General Provisions § 600.006-86 Data and...

40 CFR 600.006-89 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

... fuel economy vehicles. 600.006-89 Section 600.006-89 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-General Provisions § 600.006-89 Data and...
Vehicle type choice under the influence of a tax reform and rising fuel prices

DEFF Research Database (Denmark)

Mabit, Stefan Lindhard

2014-01-01

change in new vehicle purchases toward more diesel vehicles and more fuel-efficient vehicles. The paper analyses to what extent a vehicle tax reform similar to the Danish 2007 reform may explain changes in purchasing behaviour. The paper investigates the effects of a tax reform, fuel price changes......, and technological development on vehicle type choice using a mixed logit model. The model allows a simulation of the effect of car price changes that resemble those induced by the tax reform. This effect is compared to the effects of fuel price changes and technology improvements. The simulations show...... that the effect of the tax reform on fuel efficiency is similar to the effect of rising fuel prices while the effect of technological development is much larger. The conclusion is that while the tax reform appeared in the same year as a large increase in fuel efficiency, it seems likely that it only explains...
Development of wireless vehicle remote control for fuel lid operation

Science.gov (United States)

Sulaiman, N.; Jadin, M. S.; Najib, M. S.; Mustafa, M.; Azmi, S. N. F.

2018-04-01

Nowadays, the evolution of the vehicle technology had made the vehicle especially car to be equipped with a remote control to control the operation of the locking and unlocking system of the car’s door and rear’s bonnet. However, for the fuel or petrol lid, it merely can be opened from inside the car’s cabin by handling the fuel level inside the car’s cabin to open the fuel lid. The petrol lid can be closed by pushing the lid by hand. Due to the high usage of using fuel lever to open the fuel lid when refilling the fuel, the car driver might encounter the malfunction of fuel lid (fail to open) when pushing or pulling the fuel lever. Thus, the main aim of the research is to enhance the operation of an existing car remote control where the car fuel lid can be controlled using two techniques; remote control-based and smartphone-based. The remote control is constructed using Arduino microcontroller, wireless sensors and XCTU software to set the transmitting and receiving parameters. Meanwhile, the smartphone can control the operation of the fuel lid by communicating with Arduino microcontroller which is attached to the fuel lid using Bluetooth sensor to open the petrol lid. In order to avoid the conflict of instruction between wireless systems with the existing mechanical-based system, the servo motor will be employed to release the fuel lid merely after receiving the instruction from Arduino microcontroller and smartphone. As a conclusion, the prototype of the multipurpose vehicle remote control is successfully invented, constructed and tested. The car fuel lid can be opened either using remote control or smartphone in a sequential manner. Therefore, the outcome of the project can be used to serve as an alternative solution to solve the car fuel lid problem even though the problem rarely occurred.
Going global: LNG could open up gas market

International Nuclear Information System (INIS)

Jaremko, D.

2004-01-01

The probability of liquefied natural gas becoming a major source of energy in North America is discussed. Although the safety of the technology of transporting LNG was proven more than 40 years ago, there are considerable hurdles to be overcome when it comes to establishing LNG terminals. Industry insiders contend that the obstacles to finding suitable sites are primarily NIMBY (not-in-my-backyard) or BANANA (build-absolutely-nothing-anywhere-near-anyone) issues that will be overcome in time with better public information as to what the real hazards are, but the time is not yet ripe for any serious LNG development. Proposed LNG projects in Malaysia, Nigeria, Angola are reviewed, in addition to four projects in the United States, one in the Gulf of Mexico, and three along the American east coast. A Canadian project at Bear Head near Point Tupper, Nova Scotia, which has support from the business community, government and industry, and would provide the shortest distance to eastern North American markets for Atlantic basin shippers is also reviewed. LNG technological and transportation issues apart, there is also direct competition from the long-proposed Alaska pipeline which, if and when built, will provide long-term steady supply of gas for the U. S. market. Alaskan natural gas is clearly the preferred alternative to LNG at the present time
Approximate Pressure Distribution in an Accelerating Launch-Vehicle Fuel Tank

Science.gov (United States)

Nemeth, Michael P.

2010-01-01

A detailed derivation of the equations governing the pressure in a generic liquid-fuel launch vehicle tank subjected to uniformly accelerated motion is presented. The equations obtained are then for the Space Shuttle Superlightweight Liquid-Oxygen Tank at approximately 70 seconds into flight. This generic derivation is applicable to any fuel tank in the form of a surface of revolution and should be useful in the design of future launch vehicles
Optimum Performance of Direct Hydrogen Hybrid Fuel Cell Vehicles

OpenAIRE

Zhao, Hengbing; Burke, Andy

2009-01-01

Proton Exchange Membrane fuel cell (PEMFC) technology is one of the most attractive candidates for transportation applications due to its inherently high efficiency and high power density. However, the fuel cell system efficiency can suffer because of the need for forced air supply and water-cooling systems. Hence the operating strategy of the fuel cell system can have a significant impact on the fuel cell system efficiency and thus vehicle fuel economy. The key issues are how the fuel cell b...
The simple economics of motor vehicle pollution: A case for fuel tax

International Nuclear Information System (INIS)

Montag, Josef

2015-01-01

The volume of pollution produced by an automobile is determined by driver's behavior along three margins: (i) vehicle selection, (ii) kilometers driven, and (iii) on-road fuel economy. The first two margins have been studied extensively, however the third has received scant attention. How significant is this ‘intensive margin’? What would be the optimal policies when it is taken into account? The paper develops and analyzes a simple model of the technical and behavioral mechanisms that determine the volume emissions produced by a car. The results show that an optimal fuel tax would provide drivers with appropriate incentives along all three margins and that only public information is needed for a fuel tax to be set optimally. In contrast, an optimal distance tax would require private information. Lastly, relative to the optimal fuel tax, a simple uniform fuel tax is shown to be progressive. Thus, being already deployed worldwide, a uniform fuel tax is an attractive second-best policy. These findings should be accounted for when designing new mechanisms to alleviate motor vehicle pollution. -- Highlights: •The paper analyzes motor vehicle pollution and optimal policy responses. •The intensive margin of vehicle use (on-road fuel consumption) is modeled explicitly. •An optimal fuel tax requires only public information, unlike an optimal distance tax. •Fuel taxes should remain the core instrument for car pollution control. •Other policies, such as a car tax, may complement fuel taxes but are not substitutes
New vehicle fuel economy in the UK: Impact of the recession and recent policies

International Nuclear Information System (INIS)

Wadud, Zia

2014-01-01

Interests in vehicle fuel economy have increased in the past few years with the implementations of more stringent CAFE standard in USA and mandatory carbon emission standard in the EU. We seek to understand the effects of recent policies such as restructuring of Vehicle Excise Duties and EU standard on new vehicle fuel economy in the UK. In the past few years there have been substantial fluctuations in income and fuel prices, offering an interesting testing ground to understand their impact on the demand for fuel economy in vehicles. We use a monthly dataset to find that the emission standard is the largest driver for fuel economy improvements in recent years. Also, contrary to some recent findings in Europe and in UK, we find that income has an effect and that the recession had some role in improving the fuel economy. The effects of fuel prices were relatively small. Restructuring of the VED also improved new vehicle fuel economy in the UK, but the scrappage scheme had no significant effect. Results indicate that both supply and demand side policies are effective in improving fuel economy, although quantitatively the emission standard appears more effective due to its stringency. It is also important to consider the effects of income while devising demand side policies. - Highlights: • Econometric modelling and simulation of new vehicle fuel economy in UK. • EU carbon standard is the largest reason behind improving fuel economy. • Recession and associated reduction in income also had a role. • Fuel price has some impact on new car fuel economy, but small. • VED restructuring had an impact, but scrappage scheme's impact was insignificant
Distribution of gas from Canaport LNG

International Nuclear Information System (INIS)

Thompson, W.

2006-01-01

Construction of the Canaport Liquefied Natural Gas (LNG) project will begin in 2006. Public consultations are currently being held for the 145 km pipeline from Canaport to Bailleyville, Maine. It is expected that both the facility and the pipeline will be operational by 2008. This presentation provided details of the New Brunswick (NB) Department of Energy's (DOE) regulatory oversight of the Canaport Liquefied Natural Gas (LNG) project. The DOE is responsible for ensuring diversity and security of supply; economic efficiency; economic development opportunities and protection of the environment. The Canaport LNG facility will provide an additional 500 to 600 temporary jobs over a 2 to 3 year period, as well as 20 full-time jobs once the plant is operational. Tax revenues, access roads and the construction of a pipeline to Bailleyville, Maine will also have positive impacts on the NB economy. The facility will provide a secure long term supply of natural gas for the region. In order to support its energy goals, the DOE has proposed amendments to provide for the distribution of gas from the plant to NB customers. A proposed LNG franchise to allow for direct distribution of gas from the LNG plant to customers was discussed. Issues concerning the Gas Distribution Act and the New Pipeline Act of 2006 were also examined. It was concluded that public consultations are currently being held for the 145 km pipeline, and that both the facility and the pipeline are expected to be operational by 2008. refs., tabs., figs
Siting considerations for LNG import terminals

Energy Technology Data Exchange (ETDEWEB)

Meratla, Z. [CDS Research Ltd., Vancouver, BC (Canada)

2005-07-01

Site selection criteria for liquefied natural gas (LNG) facilities and terminals were reviewed in this PowerPoint presentation. Onshore and offshore sites were discussed. Typical public opposition issues were examined, including public concerns over safety and the environment. Low key consultation processes with local communities was advised to assess levels of interest and opposition during initial stages. It was suggested that desirable LNG sites should not be visible from local communities. Remoteness from built-up areas was advised, as well as ensuring that sites meet the requirements of future expansion and large LNG carriers. Issues concerning waterway drawbacks and exclusion zones were examined, as well as the relative merits of onshore and offshore terminals. It was noted that onshore terminals are accessible to personnel as well as outside emergency response resources, and are less susceptible to weather related downtime. In addition, onshore spills are generally impounded. Offshore LNG import terminals are visible from shorelines and susceptible to stray marine traffic and abnormal events. Siting considerations for offshore facilities include sensitive areas; shipping channels; foundation issues; shipping lane access; and offshore pipeline lengths. Issues concerning loading arms, remote flare systems, integral ballast and process equipment for offshore facilities were discussed. Membrane type storage systems and tank construction details were presented as well as details of self supporting storage systems. A comparison of gravity-based structures and floating facilities was presented. It was concluded that floating LNG facilities have well developed security procedures, passive protection and automatic intruder detection alarms. tabs., figs.
Distribution of gas from Canaport LNG

Energy Technology Data Exchange (ETDEWEB)

Thompson, W. [New Brunswick Dept. of Energy, Fredericton, NB (Canada)

2006-07-01

Construction of the Canaport Liquefied Natural Gas (LNG) project will begin in 2006. Public consultations are currently being held for the 145 km pipeline from Canaport to Bailleyville, Maine. It is expected that both the facility and the pipeline will be operational by 2008. This presentation provided details of the New Brunswick (NB) Department of Energy's (DOE) regulatory oversight of the Canaport Liquefied Natural Gas (LNG) project. The DOE is responsible for ensuring diversity and security of supply; economic efficiency; economic development opportunities and protection of the environment. The Canaport LNG facility will provide an additional 500 to 600 temporary jobs over a 2 to 3 year period, as well as 20 full-time jobs once the plant is operational. Tax revenues, access roads and the construction of a pipeline to Bailleyville, Maine will also have positive impacts on the NB economy. The facility will provide a secure long term supply of natural gas for the region. In order to support its energy goals, the DOE has proposed amendments to provide for the distribution of gas from the plant to NB customers. A proposed LNG franchise to allow for direct distribution of gas from the LNG plant to customers was discussed. Issues concerning the Gas Distribution Act and the New Pipeline Act of 2006 were also examined. It was concluded that public consultations are currently being held for the 145 km pipeline, and that both the facility and the pipeline are expected to be operational by 2008. refs., tabs., figs.
FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)
Method for modeling driving cycles, fuel use, and emissions for over snow vehicles.

Science.gov (United States)

Hu, Jiangchuan; Frey, H Christopher; Sandhu, Gurdas S; Graver, Brandon M; Bishop, Gary A; Schuchmann, Brent G; Ray, John D

2014-07-15

As input to a winter use plan, activity, fuel use, and tailpipe exhaust emissions of over snow vehicles (OSV), including five snow coaches and one snowmobile, were measured on a designated route in Yellowstone National Park (YNP). Engine load was quantified in terms of vehicle specific power (VSP), which is a function of speed, acceleration, and road grade. Compared to highway vehicles, VSP for OSVs is more sensitive to rolling resistance and less sensitive to aerodynamic drag. Fuel use rates increased linearly (R2>0.96) with VSP. For gasoline-fueled OSVs, fuel-based emission rates of carbon monoxide (CO) and nitrogen oxides (NOx) typically increased with increasing fuel use rate, with some cases of very high CO emissions. For the diesel OSVs, which had selective catalytic reduction and diesel particulate filters, fuel-based NOx and particulate matter (PM) emission rates were not sensitive to fuel flow rate, and the emission controls were effective. Inter vehicle variability in cycle average fuel use and emissions rates for CO and NOx was substantial. However, there was relatively little inter-cycle variation in cycle average fuel use and emission rates when comparing driving cycles. Recommendations are made regarding how real-world OSV activity, fuel use, and emissions data can be improved.
Emissions deterioration for three alternative fuel vehicle types: Natural gas, ethanol, and methanol vehicles

International Nuclear Information System (INIS)

Winebrake, J.J.; Deaton, M.L.

1997-01-01

Although there have been several studies examining emissions from in-use alternative fuel vehicles (AFVs), little is known about the deterioration of these emissions over vehicle lifetimes and how this deterioration compares with deterioration from conventional vehicles (CVs). This paper analyzes emissions data from 70 AFVs and 70 CVs operating in the federal government fleet to determine whether AFV emissions deterioration differs significantly from CV emissions deterioration. The authors conduct the analysis on three alternative fuel types (natural gas, methanol, and ethanol) and on five pollutants (carbon monoxide, carbon dioxide, total hydrocarbons, non-methane hydrocarbons, and nitrogen oxides). They find that for most cases they studied, deterioration differences are not statistically significant; however, several exceptions suggest that air quality planners and regulators must further analyze AFV emissions deterioration in order to properly include these technologies into broader air quality management schemes
First LNG deliveries from Qatar to Japan

International Nuclear Information System (INIS)

Legros, E.J.

1997-01-01

Twenty five years after the discovery of the giant North Field natural gas deposit, the Qatargas company has delivered its first LNG freight to Japan in December 1996. This paper recalls the history of the company from the discovery of the offshore North Field, its valorization and development, the LNG project with the building of the Ras Laffan harbour and its condensates processing factory and the 3 offshore production platforms. Ten methane-tanker ships will be in operation in the year 2000. Qatar's LNG exports should reach 20 to 25 Mt/year in the next ten years, when all its liquefaction factory projects will be completed. (J.S.)
Flex-fuel vehicle adoption and dynamics of ethanol prices: lessons from Brazil

International Nuclear Information System (INIS)

Du, Xiaodong; Carriquiry, Miguel A.

2013-01-01

Focusing on dynamics of the relative prices of substitute fuels, namely ethanol and gasoline, this study quantifies the impact of the increase in shares of flex-fuel vehicles (FFVs) in the vehicle fleet on the domestic ethanol prices in Brazil. A modified partial adjustment model is employed. Estimation results provide strong support for our research hypotheses: (i) when consumers can choose between the fuels the relative ethanol and gasoline prices converge to a long-run equilibrium level, which is determined by the fuel economy, and (ii) price dynamics are largely determined by market supply and demand factors including the price of sugar, ethanol exports, and composition of vehicle fleet. Furthermore, the impacts of demand factors such as ethanol exports are strengthened by the increasing proportion of FFVs in the vehicle fleet. - Highlights: • The relative prices of ethanol and gasoline in Brazil exhibit strong mean-reversion. • The fuel price dynamics are mainly influenced by supply and demand factors. • The impacts of demand factors are strengthened by the increasing proportion of FFVs
Hydrogen plant module (HPM) and vehicle fueled by same.

Science.gov (United States)

2011-09-29

The goal / objective of the project was to design and fabricate hydrogen plant module (HPM) that is capable of producing : hydrogen fuel onboard a vehicle and that obviates one or more of the present issues related to compressed hydrogen fuel : stora...
Autonomy-Enabled Fuel Savings for Military Vehicles: Report on 2016 Aberdeen Test Center Testing

Energy Technology Data Exchange (ETDEWEB)

Ragatz, Adam [National Renewable Energy Lab. (NREL), Golden, CO (United States); Prohaska, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gonder, Jeff [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-05-26

Fuel savings have never been the primary focus for autonomy-enabled military vehicles. However, studies have estimated that autonomy in passenger and commercial vehicles could improve fuel economy by as much as 22%-33% over various drive cycles. If even a fraction of this saving could be realized in military vehicles, significant cost savings could be realized each year through reduced fuel transport missions, reduced fuel purchases, less maintenance, fewer required personnel, and increased vehicle range. Researchers from the National Renewable Energy Laboratory installed advanced data logging equipment and instrumentation on two autonomy-enabled convoy vehicles configured with Lockheed Martin's Autonomous Mobility Applique System to determine system performance and improve on the overall vehicle control strategies of the vehicles. Initial test results from testing conducted at the U.S. Army Aberdeen Test Center at the Aberdeen Proving Grounds are included in this report. Lessons learned from in-use testing and performance results have been provided to the project partners for continued system refinement.
Super-capacitors fuel-cell hybrid electric vehicle optimization and control strategy development

International Nuclear Information System (INIS)

Paladini, Vanessa; Donateo, Teresa; De Risi, Arturo; Laforgia, Domenico

2007-01-01

In the last decades, due to emissions reduction policies, research focused on alternative powertrains among which hybrid electric vehicles (HEVs) powered by fuel cells are becoming an attractive solution. One of the main issues of these vehicles is the energy management in order to improve the overall fuel economy. The present investigation aims at identifying the best hybrid vehicle configuration and control strategy to reduce fuel consumption. The study focuses on a car powered by a fuel cell and equipped with two secondary energy storage devices: batteries and super-capacitors. To model the powertrain behavior an on purpose simulation program called ECoS has been developed in Matlab/Simulink environment. The fuel cell model is based on the Amphlett theory. The battery and the super-capacitor models account for charge/discharge efficiency. The analyzed powertrain is also equipped with an energy regeneration system to recover braking energy. The numerical optimization of vehicle configuration and control strategy of the hybrid electric vehicle has been carried out with a multi objective genetic algorithm. The goal of the optimization is the reduction of hydrogen consumption while sustaining the battery state of charge. By applying the algorithm to different driving cycles, several optimized configurations have been identified and discussed
Gas and LNG pricing and trading hub in East Asia: An introduction

Directory of Open Access Journals (Sweden)

Xunpeng Shi

2016-10-01

Full Text Available This paper summarizes the four papers in the special issues on ‘Gas and LNG pricing and trading hub in East Asia’. The papers examine lessons and experience from European hub development, other commodity, the Japanese history on developing of futures markets and inter-fuel substitution in East Asia. The papers finds that liquid futures market is the key to formulate benchmark prices while a well-developed spot market is the foundation; political will and strong leadership are required to overcome the power of incumbents and to restructure the gas market that impede the the development of competitive markets; and East Asia needs to develop its indigenous gas or LNG trading hubs even in low oil prices period and its developing market allows easier changes in new contracts than in existing ones. This hub development requires governments to go through tough domestic market reforms, including liberalization and cooperation with each other and with gas exporters.

Vehicle Technologies and Fuel Cell Technologies Program: Prospective Benefits Assessment Report for Fiscal Year 2016

Energy Technology Data Exchange (ETDEWEB)

Stephens, T. S. [Argonne National Lab. (ANL), Argonne, IL (United States); Taylor, C. H. [TA Engineering, Inc., Catonsville, MD (United States); Moore, J. S. [TA Engineering, Inc., Catonsville, MD (United States); Ward, J. [United States Department of Energy, Washington, DC (United States). Office of Energy Efficiency and Renewable Energy

2016-02-23

Under a diverse set of programs, the Vehicle Technologies and Fuel Cell Technologies offices of DOE’s Office of Energy Efficiency and Renewable Energy invest in research, development, demonstration, and deployment of advanced vehicle, hydrogen production, delivery and storage, and fuel cell technologies. This report estimates the benefits of successfully developing and deploying these technologies (a “Program Success” case) relative to a base case (the “No Program” case). The Program Success case represents the future with completely successful deployment of Vehicle Technologies Office (VTO) and Fuel Cell Technologies Office (FCTO) technologies. The No Program case represents a future in which there is no contribution after FY 2016 by the VTO or FCTO to these technologies. The benefits of advanced vehicle, hydrogen production, delivery and storage, and fuel cell technologies were estimated on the basis of differences in fuel use, primary energy use, and greenhouse gas (GHG) emissions from light-, medium- and heavy-duty vehicles, including energy and emissions from fuel production, between the base case and the Program Success case. Improvements in fuel economy of various vehicle types, growth in the stock of fuel cell vehicles and other advanced technology vehicles, and decreased GHG intensity of hydrogen production and delivery in the Program Success case over the No Program case were projected to result in savings in petroleum use and GHG emissions. Benefits were disaggregated by individual program technology areas, which included the FCTO program and the VTO subprograms of batteries and electric drives; advanced combustion engines; fuels and lubricants; materials (for reduction in vehicle mass, or “lightweighting”); and, for medium- and heavy-duty vehicles, reduction in rolling and aerodynamic resistance. Projections for the Program Success case indicate that by 2035, the average fuel economy of on-road, light-duty vehicle stock could be 47% to 76
Alternative Fuel Vehicles: The Case of Compressed Natural Gas (CNG) Vehicles in California Households

OpenAIRE

Abbanat, Brian A.

2001-01-01

Compressed natural gas (CNG) vehicles have been used internationally by fleets and households for decades. The use of CNG vehicles results in less petroleum consumption, and fewer air pollutant and greenhouse gas emissions in most applications. In the United States, the adoption of CNG technology has been slowed by the availability of affordable gasoline and diesel fuel. This study addresses the potential market for CNG vehicles at the consumer level in California. Based on semi-structured pe...
Evolving natural gas markets: LNG possibilities for a hydrothermal power system

Energy Technology Data Exchange (ETDEWEB)

Correia, Tiago B.; Resende, Joao P.; Costa, Agnes M. [Brazilian Ministry of Mines and Energy, Brasilia, DF (Brazil)

2008-07-01

The latest advancements in the natural gas - NG industry have brought new opportunities for the resource's application, especially in the power industry. On the one hand, rapid growth in demand and falling costs of transportation over long distances, particularly as liquefied natural gas - LNG, should lead to a more integrated NG world market. On the other, the deregulation of electricity markets and the growth of independent power producers - IPPs using NG as a fuel for generating peak load power have increased the demand for more flexible NG supply contracts. These factors have allowed a shift in the timing of investment and contract negotiation in NG market. Traditionally, firms searched for trading partners and signed long-term contracts before investing in infrastructure. In the evolving LNG market, producers invest in infrastructure before they have buyers for all their expected outputs, while buyers undertake investment before having firm contracts for all their expected NG needs. These technological and market changes may foster greater participation of a fully flexible NG power plants in the Brazilian electricity market. Nowadays, thermal power long-term capacity contracts customized and negotiated in the local electricity pool (ACR) require power producer to award guarantees of NG firm supply, substantially increasing their cost. A combination of flexible LNG supply contracts and electricity pool contracts may present a solution to the lack of competitiveness of NG power plants in the Brazilian power industry. (author)
Fuel and vehicle technology choices for passenger vehicles in achieving stringent CO2 targets: connections between transportation and other energy sectors.

Science.gov (United States)

Grahn, M; Azar, C; Williander, M I; Anderson, J E; Mueller, S A; Wallington, T J

2009-05-01

The regionalized Global Energy Transition (GET-R 6.0) model has been modified to include a detailed description of light-duty vehicle options and used to investigate the potential impact of carbon capture and storage (CCS) and concentrating solar power (CSP) on cost-effective fuel/vehicle technologies in a carbon-constrained world. Total CO2 emissions were constrained to achieve stabilization at 400-550 ppm, by 2100, at lowesttotal system cost The dominantfuel/vehicle technologies varied significantly depending on CO2 constraint future cost of vehicle technologies, and availability of CCS and CSP. For many cases, no one technology dominated on a global scale. CCS provides relatively inexpensive low-CO2 electricity and heatwhich prolongs the use of traditional ICEVs. CSP displaces fossil fuel derived electricity, prolongs the use of traditional ICEVs, and promotes electrification of passenger vehicles. In all cases considered, CCS and CSP availability had a major impact on the lowest cost fuel/vehicle technologies, and alternative fuels are needed in response to expected dwindling oil and natural gas supply potential by the end of the century.
75 FR 58077 - Revisions and Additions to Motor Vehicle Fuel Economy Label

Science.gov (United States)

2010-09-23

...The Environmental Protection Agency (EPA) and the National Highway Traffic Safety Administration (NHTSA) are conducting a joint rulemaking to redesign and add information to the current fuel economy label that is posted on the window sticker of all new cars and light- duty trucks sold in the U.S. The redesigned label will provide new information to American consumers about the fuel economy and consumption, fuel costs, and environmental impacts associated with purchasing new vehicles beginning with model year 2012 cars and trucks. This action will also develop new labels for certain advanced technology vehicles, which are poised to enter the U.S. market, in particular plug-in hybrid electric vehicles and electric vehicles. NHTSA and EPA are proposing these changes because the Energy Independence and Security Act (EISA) of 2007 imposes several new labeling requirements, because the agencies believe that the current labels can be improved to help consumers make more informed vehicle purchase decisions, and because the time is right to develop new labels for advanced technology vehicles that are being commercialized. This proposal is also consistent with the recent joint rulemaking by EPA and NHTSA that established harmonized federal greenhouse gas (GHG) emissions and corporate average fuel economy (CAFE) standards for new cars, sport utility vehicles, minivans, and pickup trucks for model years 2012-2016.
Liquefied natural gas (LNG) : production, storage and handling. 7. ed.

Energy Technology Data Exchange (ETDEWEB)

Kalra, S; Jaron, K; Adragna, M; Coyle, S; Foley, C; Hawryn, S; Martin, A; McConnell, J [eds.

2003-07-01

This Canadian Standard on the production, storage and handling of liquefied natural gas (LNG) was prepared by the Technical Committee on Liquefied Natural Gas under the jurisdiction of the Steering Committee on Oil and Gas Industry Systems and Materials. It establishes the necessary requirements for the design, installation and safe operation of LNG facilities. The Standard applies to the design, location, construction, operation and maintenance of facilities at any location of the liquefaction of natural gas and for the storage, vaporization, transfer, handling and truck transport of LNG. The training of personnel involved is also included as well as containers for LNG storage, including insulated vacuum systems. It includes non-mandatory guidelines for small LNG facilities but does not apply to the transportation of refrigerants, LNG by rail, marine vessel or pipeline. This latest edition contains changes in working of seismic design requirements and minor editorial changes to several clauses to bring the Standard closer to the US National Fire Protection Association's Committee on Liquefied Natural Gas Standard while maintaining Canadian regulatory requirements. The document is divided into 12 sections including: general requirements; plant site provisions; process equipment; stationary LNG storage containers; vaporization facilities; piping system and components; instrumentation and electrical services; transfer of LNG and refrigerants; fire protection, safety and security; and, operating, maintenance and personnel training. This Standard, like all Canadian Standards, was subject to periodic review and was most recently reaffirmed in 2003. 6 tabs., 6 figs., 3 apps.
Fuel Options for Vehicles in Korea and Role of Nuclear Energy

International Nuclear Information System (INIS)

Jeong, Yong Hoon; Chang, Soon Heung

2005-01-01

Nowadays, almost all vehicles in Korea are powered by gasoline or diesel and they are emitting about 25% of nationwide total carbon dioxide emission. With jetting up price of oil and concerns about global warming by use of fossil fuel, transition to the hydrogen economy gains more and more interest. As alternatives to the current fossil powered vehicles, hybrid, hydrogen, electricity powered vehicles are considered. In short term we will reduce dependence upon fossil fuel by using hybrid cars. However, in the long term, we have to escape from the dependence on fossil fuel. In this context, nuclear-driven hydrogen or electricity powered cars are the alternatives. In this study, we estimated the operation cost of cars powered by hydrogen and electricity from nuclear power and studied about the major blocks on the way to independence from fossil fuels. In the analysis, we put the capital cost of car aside
The Phoenix series large scale LNG pool fire experiments.

Energy Technology Data Exchange (ETDEWEB)

Simpson, Richard B.; Jensen, Richard Pearson; Demosthenous, Byron; Luketa, Anay Josephine; Ricks, Allen Joseph; Hightower, Marion Michael; Blanchat, Thomas K.; Helmick, Paul H.; Tieszen, Sheldon Robert; Deola, Regina Anne; Mercier, Jeffrey Alan; Suo-Anttila, Jill Marie; Miller, Timothy J.

2010-12-01

The increasing demand for natural gas could increase the number and frequency of Liquefied Natural Gas (LNG) tanker deliveries to ports across the United States. Because of the increasing number of shipments and the number of possible new facilities, concerns about the potential safety of the public and property from an accidental, and even more importantly intentional spills, have increased. While improvements have been made over the past decade in assessing hazards from LNG spills, the existing experimental data is much smaller in size and scale than many postulated large accidental and intentional spills. Since the physics and hazards from a fire change with fire size, there are concerns about the adequacy of current hazard prediction techniques for large LNG spills and fires. To address these concerns, Congress funded the Department of Energy (DOE) in 2008 to conduct a series of laboratory and large-scale LNG pool fire experiments at Sandia National Laboratories (Sandia) in Albuquerque, New Mexico. This report presents the test data and results of both sets of fire experiments. A series of five reduced-scale (gas burner) tests (yielding 27 sets of data) were conducted in 2007 and 2008 at Sandia's Thermal Test Complex (TTC) to assess flame height to fire diameter ratios as a function of nondimensional heat release rates for extrapolation to large-scale LNG fires. The large-scale LNG pool fire experiments were conducted in a 120 m diameter pond specially designed and constructed in Sandia's Area III large-scale test complex. Two fire tests of LNG spills of 21 and 81 m in diameter were conducted in 2009 to improve the understanding of flame height, smoke production, and burn rate and therefore the physics and hazards of large LNG spills and fires.
Fuel Cell Electric Vehicles: Drivers and Impacts of Adoption.

Energy Technology Data Exchange (ETDEWEB)

Levinson, Rebecca Sobel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); West, Todd H. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Manley, Dawn K. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-11-01

We present scenario and parametric analyses of the US light duty vehicle (LDV) stock, sim- ulating the evolution of the stock in order to assess the potential role and impacts of fuel cell electric vehicles (FCEVs). The analysis probes the competition of FCEVs with other LDVs and the effects of FCEV adoption on LDV fuel use and emissions. We parameterize commodity and technology prices in order to explore the sensitivities of FCEV sales and emissions to oil, natural gas, battery technology, fuel cell technology, and hydrogen produc- tion prices. We additionally explore the effects of vehicle purchasing incentives for FCEVs, identifying potential impacts and tipping points. Our analyses lead to the following conclu- sions: (1) In the business as usual scenario, FCEVs comprise 7% of all new LDV sales by 2050. (2) FCEV adoption will not substantially impact green house gas emissions without either policy intervention, significant increases in natural gas prices, or technology improve- ments that motivate low carbon hydrogen production. (3) FCEV technology cost reductions have a much greater potential for impact on FCEV sales than hydrogen fuel cost reductions. (4) FCEV purchasing incentives must be both substantial and sustained in order to motivate lasting changes to FCEV adoption.
The Pacific Basin LNG trade: a return to fundamentals

International Nuclear Information System (INIS)

Baharuddin, H.

1991-01-01

The LNG business in the Pacific Region is unique because there is no other source of energy in which seller and buyer sign contracts for 20-year periods. This long-term relationship is based on mutual buyer/seller cooperation, and mutual buyer/seller recognition of the financial and commercial challenges faced by all links in the LNG Supply Chain. However, there are now concerns that those involved in the LNG business were ignoring the fundamentals of the trade. The buyer expected the seller to absorb higher transportation costs, easing take or pay terms, more flexibility, evergreen options on uncommitted capacity, etc. On the other side, sellers expected larger baseload quantities, equitable sharing of LNG chain risks with consumers. (author)
The Asia Pacific LNG trade: Status and technology development

International Nuclear Information System (INIS)

Hovdestad, W.R.

1995-01-01

The Asia Pacific Region is experiencing a period of sustained economic expansion. Economic growth has led to an increasing demand for energy that has spurred a rapid expansion of baseload liquefied natural gas (LNG) facilities in this region. This is illustrated by the fact that seven of the ten baseload facilities in existence provide LNG for markets in the Asia Pacific region. With the three exceptions having been initially commissioned in 1972 and earlier, it is fair to observed that most advances in LNG technology have been developed and applied for this market. The paper presents the current status and identified future trends for the Asia Pacific LNG trade. Technology development in terms of application to onstream production, processing and transportation facilities, including LNG tankers, is presented. The potential of future advances to applied technology and operational practices to improve the cost-effectiveness of new and existing facilities is discussed. Current design data and methods as actually used are examined in terms of identifying where fundamental research and basic physical data are insufficient for optimization purposes. These findings are then summarized and presented in terms of the likely evolution of future and existing LNG projects in the Asia Pacific region
Regulation on the transport of nuclear fuel materials by vehicles

International Nuclear Information System (INIS)

1984-01-01

The regulations applying to the transport of nuclear fuel materials by vehicles, mentioned in the law for the regulations of nuclear source materials, nuclear fuel materials and reactors. The transport is for outside of the factories and the site of enterprises by such modes of transport as rail, trucks, etc. Covered are the following: definitions of terms, places of fuel materials handling, loading methods, limitations on mix loading with other cargo, radiation dose rates concerning the containers and the vehicles, transport indexes, signs and indications, limitations on train linkage during transport by rail, security guards, transport of empty containers, etc. together with ordinary rail cargo and so on. (Mori, K.)
Clean Cities Guide to Alternative Fuel and Advanced Medium- and Heavy-Duty Vehicles (Book)

Energy Technology Data Exchange (ETDEWEB)

2013-08-01

Today's fleets are increasingly interested in medium-duty and heavy-duty vehicles that use alternative fuels or advanced technologies that can help reduce operating costs, meet emissions requirements, improve fleet sustainability, and support U.S. energy independence. Vehicle and engine manufacturers are responding to this interest with a wide range of options across a steadily growing number of vehicle applications. This guide provides an overview of alternative fuel power systems?including engines, microturbines, electric motors, and fuel cells?and hybrid propulsion systems. The guide also offers a list of individual medium- and heavy-duty vehicle models listed by application, along with associated manufacturer contact information, fuel type(s), power source(s), and related information.
Refueling availability for alternative fuel vehicle markets: Sufficient urban station coverage

International Nuclear Information System (INIS)

Melaina, Marc; Bremson, Joel

2008-01-01

Alternative fuel vehicles can play an important role in addressing the challenges of climate change, energy security, urban air pollution and the continued growth in demand for transportation services. The successful commercialization of alternative fuels for vehicles is contingent upon a number of factors, including vehicle cost and performance. Among fuel infrastructure issues, adequate refueling availability is one of the most fundamental to successful commercialization. A commonly cited source reports 164,300 refueling stations in operation nationwide. However, from the perspective of refueling availability, this nationwide count tends to overstate the number of stations required to support the widespread deployment of alternative fuel vehicles. In terms of spatial distribution, the existing gasoline station networks in many urban areas are more than sufficient. We characterize a sufficient level of urban coverage based upon a subset of cities served by relatively low-density station networks, and estimate that some 51,000 urban stations would be required to provide this sufficient level of coverage to all major urban areas, 33 percent less than our estimate of total urban stations. This improved characterization will be useful for engineering, economic and policy analyses. (author)
Novel design of LNG (liquefied natural gas) reliquefaction process

Energy Technology Data Exchange (ETDEWEB)

Baek, S., E-mail: s.baek@kaist.ac.kr [Cryogenic Engineering Laboratory, Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, 373-1, Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Hwang, G.; Lee, C. [Cryogenic Engineering Laboratory, Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, 373-1, Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Jeong, S., E-mail: skjeong@kaist.ac.kr [Cryogenic Engineering Laboratory, Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, 373-1, Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Choi, D. [Cryogenic Engineering Laboratory, Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, 373-1, Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Ship/Plant System R and D Team, Daewoo Shipbuilding and Marine Engineering Co., Ltd., 1, Ajoo, Koje, Kyungnam 656-714 (Korea, Republic of)

2011-08-15

Highlights: {yields} We performed experiments with LN2 to mock up the new LNG reliquefaction process. {yields} Subcooled liquid goes to heat exchanger, heater, and phase separator. {yields} Reliquefaction occurs when vapor enters heat exchanger and verified by experiments. {yields} Reliquefaction ratio increases when subcooling degree or system pressure increases. - Abstract: This paper presents an investigation of novel LNG reliquefaction process where the cold exergy of subcooled LNG is utilized to recondense the vaporized light component of LNG after it is separated from the heavier component in a phase separator. The regeneration of cold exergy is especially effective as well as important in thermodynamic sense when a cryogenic process is involved. To verify the proposed idea, we performed an experimental study by facilitating liquid nitrogen apparatus to mock up the LNG reliquefaction process. Subcooled liquid nitrogen is produced for a commercial transportation container with a house-made atmospheric liquid nitrogen heat exchanger and then, having subooled degree of up to 19 K, it simulates the behavior of subcooled LNG in the lab-scale reliquefaction experiment. Recondensation of the vaporized gas is possible by using the cold exergy of subcooled liquid in a properly fabricated heat exchanger. Effect of heat exchanger performance factor and degree of subcooling on recondensation portion has been discussed in this paper. It is concluded that utilizing pressurized subcooled liquid that is obtained by liquid pump can surely reduce the pumping power of the vaporized natural gas and save the overall energy expenditure in LNG reliquefaction process.
Novel design of LNG (liquefied natural gas) reliquefaction process

International Nuclear Information System (INIS)

Baek, S.; Hwang, G.; Lee, C.; Jeong, S.; Choi, D.

2011-01-01

Highlights: → We performed experiments with LN2 to mock up the new LNG reliquefaction process. → Subcooled liquid goes to heat exchanger, heater, and phase separator. → Reliquefaction occurs when vapor enters heat exchanger and verified by experiments. → Reliquefaction ratio increases when subcooling degree or system pressure increases. - Abstract: This paper presents an investigation of novel LNG reliquefaction process where the cold exergy of subcooled LNG is utilized to recondense the vaporized light component of LNG after it is separated from the heavier component in a phase separator. The regeneration of cold exergy is especially effective as well as important in thermodynamic sense when a cryogenic process is involved. To verify the proposed idea, we performed an experimental study by facilitating liquid nitrogen apparatus to mock up the LNG reliquefaction process. Subcooled liquid nitrogen is produced for a commercial transportation container with a house-made atmospheric liquid nitrogen heat exchanger and then, having subooled degree of up to 19 K, it simulates the behavior of subcooled LNG in the lab-scale reliquefaction experiment. Recondensation of the vaporized gas is possible by using the cold exergy of subcooled liquid in a properly fabricated heat exchanger. Effect of heat exchanger performance factor and degree of subcooling on recondensation portion has been discussed in this paper. It is concluded that utilizing pressurized subcooled liquid that is obtained by liquid pump can surely reduce the pumping power of the vaporized natural gas and save the overall energy expenditure in LNG reliquefaction process.
Consumer Views: Fuel Economy, Plug-in Electric Vehicle Battery Range, and Willingness to Pay for Vehicle Technology

Energy Technology Data Exchange (ETDEWEB)

Singer, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-05-11

This presentation includes data captured by the National Renewable Energy Laboratory (NREL) to support the U.S. Department of Energy's Vehicle Technologies Office (VTO) research efforts. The data capture consumer views on fuel economy, plug-in electric vehicle battery range, and willingness to pay for advanced vehicle technologies.
Thermodynamic Processes Involving Liquefied Natural Gas at the LNG Receiving Terminals / Procesy termodynamiczne z wykorzystaniem skroplonego gazu ziemnego w terminalach odbiorczych LNG

Science.gov (United States)

Łaciak, Mariusz

2013-06-01

The increase in demand for natural gas in the world, cause that the production of liquefied natural gas (LNG) and in consequences its regasification becoming more common process related to its transportation. Liquefied gas is transported in the tanks at a temperature of about 111K at atmospheric pressure. The process required to convert LNG from a liquid to a gas phase for further pipeline transport, allows the use of exergy of LNG to various applications, including for electricity generation. Exergy analysis is a well known technique for analyzing irreversible losses in a separate process. It allows to specify the distribution, the source and size of the irreversible losses in energy systems, and thus provide guidelines for energy efficiency. Because both the LNG regasification and liquefaction of natural gas are energy intensive, exergy analysis process is essential for designing highly efficient cryogenic installations. Wzrost zapotrzebowania na gaz ziemny na świecie powoduje, że produkcja skroplonego gazu ziemnego (LNG), a w konsekwencji jego regazyfikacja, staje się coraz bardziej powszechnym procesem związanym z jego transportem. Skroplony gaz transportowany jest w zbiornikach w temperaturze około 111K pod ciśnieniem atmosferycznym. Przebieg procesu regazyfikacji niezbędny do zamiany LNG z fazy ciekłej w gazową dla dalszego transportu w sieci, umożliwia wykorzystanie egzergii LNG do różnych zastosowań, między innymi do produkcji energii elektrycznej. Analiza egzergii jest znaną techniką analizowania nieodwracalnych strat w wydzielonym procesie. Pozwala na określenie dystrybucji, źródła i wielkości nieodwracalnych strat w systemach energetycznych, a więc ustalić wytyczne dotyczące efektywnego zużycia energii. Ponieważ zarówno regazyfikacja LNG jak i skraplanie gazu ziemnego są energochłonne, proces analizy egzergii jest niezbędny do projektowania wysoce wydajnych instalacji kriogenicznych.
Heel and toe driving on fuel cell vehicle

Science.gov (United States)

Choi, Tayoung; Chen, Dongmei

2012-12-11

A system and method for providing nearly instantaneous power in a fuel cell vehicle. The method includes monitoring the brake pedal angle and the accelerator pedal angle of the vehicle, and if the vehicle driver is pressing both the brake pedal and the accelerator pedal at the same time and the vehicle is in a drive gear, activating a heel and toe mode. When the heel and toe mode is activated, the speed of a cathode compressor is increased to a predetermined speed set-point, which is higher than the normal compressor speed for the pedal position. Thus, when the vehicle brake is removed, the compressor speed is high enough to provide enough air to the cathode, so that the stack can generate nearly immediate power.
40 CFR 80.581 - What are the batch testing and sample retention requirements for motor vehicle diesel fuel, NRLM...

Science.gov (United States)

2010-07-01

... retention requirements for motor vehicle diesel fuel, NRLM diesel fuel, and ECA marine fuel? 80.581 Section...) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel... requirements for motor vehicle diesel fuel, NRLM diesel fuel, and ECA marine fuel? (a) Beginning on June 1...

40 CFR 80.593 - What are the reporting requirements for refiners and importers of motor vehicle diesel fuel...

Science.gov (United States)

2010-07-01

... for refiners and importers of motor vehicle diesel fuel subject to temporary refiner relief standards... PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive... the reporting requirements for refiners and importers of motor vehicle diesel fuel subject to...
The importance of LNG for natural gas consumption in the EU

Directory of Open Access Journals (Sweden)

Metelska Klaudia

2016-01-01

Full Text Available The World market of liquefied natural gas (LNG is growing rapidly. In 2015 LNG production exceeded 333 bcm with its predicted increase up to 450 bcm in 2019. The analysis of LNG role in natural gas import to the EU in recent years shows variability: LNG share in overall import reached 25% in 2011 and it went down to 15% in 2014. The smaller demand for natural gas including LNG in the EU can be due to, among others, a slower economic growth and a dynamic development of the use of renewable energy sources. The article shows the role of natural gas in the structure of consumption of primary energy as well as the changes in demand for natural gas in the years 2007–2014 for the main groups of end users: industry, energy production and individual households. The biggest fall in demand for natural gas has been observed in energy production sector in recent years. This publication continues to analyse the structure of natural gas supplies to the EU, with special emphasis on the directions of LNG import to the countries such as: The UK, Spain, France, Greece, Belgium, Portugal, Italy, Lithuania and The Netherlands. The significance of LNG in the balance of consumption of natural gas in these countries has been presented as well as the infrastructure connected with LNG and plans of development of regasification terminals. In the summary the most important conclusions have been drawn and a chance of the increase in significance of the role of LNG in the balance of natural gas supplies has been pointed out, which is due to the steep fall of LNG prices which has taken place in recent years.
LNG trade preparations are a decade too soon

Energy Technology Data Exchange (ETDEWEB)

Timm, S [Mar. Week; Faridany, E; Mitchell, P

1979-03-01

A discussion of papers delivered at the 6th International LNG/LPG, Gastech 78, Conference (Monte Carlo 11/7-10/78) covers an estimate by E. Faridany (Ocean Phoenix Transp. Inc.) that in 1981-85, world trade in LNG would increase by 1775 million cu ft/day (Mcfd) over the current 2720 Mcfd, but of this increment only the 460 Mcfd Panhandle project using Lake Charles, La., as a regasification terminal will be into the U.S. while all other trade will be to Europe. Of the present LNG trade, 48Vertical Bar3< goes to Japan from the Brunei (535 Mcfd, the world's largest) and Abu Dhabi projects, and only 20Vertical Bar3< goes to the U.S. Faridany's estimates of U.S. LNG imports in 1990 vary from the 8215 Mcfd ''high'' to the ''median'' forecast of 2930 Mcfd; he predicted that the proportion of incremental sources of gas supply taken up by LNG in 1990 is only 20-40Vertical Bar3< for the U.S., compared with 25Vertical Bar3< for Europe and 90Vertical Bar3< for Japan. According to P. Mitchell (Poten and Partners), world demand for LPG could rise from 9 million to 38 million tons in 1979-85.
Modeling Turkey’s future LNG supply security strategy

International Nuclear Information System (INIS)

Efe Biresselioglu, Mehmet; Hakan Demir, Muhittin; Kandemir, Cansu

2012-01-01

Turkey was among those countries which decided to increase its natural gas consumption in the 1990s, due to its relative low cost and lack of impact on the environment. However, a heavy dependence on imports, from Algeria, Qatar and Nigeria, respectively, creates a threat to energy security, both in terms of source and supply diversity. Accordingly, we follow an analytical approach to identify the accuracy of our assumption, considering the current economic, political and security risk. To this end, we formulate and solve a mixed integer programming model that determines the optimal sourcing strategy for Turkey’s increasing LNG demand. This model demonstrates a number of alternative policy options for LNG supply. Furthermore, we consider that increasing the proportion of LNG in the overall gas supply will contribute to the aim of improving Turkey’s level of energy security. - Highlights: ► Turkey’s best policy option is to increase the share of LNG. ► Turkey’s main suppliers of LNG will be Algeria, Egypt, Nigeria, and Trinidad and Tobago. ► Norway, Libya, and Oman contribute to the supply with rather smaller shares. ► With high risk scenario Algeria, Egypt, Nigeria and Libya will not be suppliers. ► Oman and Qatar will cover; even though they are high-cost suppliers.
FUEL/CARBON PRICE VS. ABATEMENT TECHNOLOGY IN FREIGHT TRANSPORT

Directory of Open Access Journals (Sweden)

Eugen Ferdinand Spangenberg

2017-12-01

Full Text Available The current situation is the exponential increase in greenhouse gases (GHG, which is mainly caused by industrial and transport activities. The recent Paris agreement in 2015 (Framework Convention on Climate Change COP21, UNFCCC made it clear to everyone that CO2 emissions are to be limited in all areas of life. Alternative fuels with a lower environmental impact than carbon (CO2 emissions are hard to find if the overall footprint is to be taken into account. Nevertheless, there are some fuels that have less impact on climate change. One the other hand, the production of biofuels is a controversial matter, although it is a viable alternative to emissions reduction. CNG or LNG-powered vehicles are also better in terms of environmental pollution, but are hardly better with regard to CO2 impact when a Life Cycle Assessment (LCA is carried out. LNG (liquid natural gas, for example, is the future fuel in the maritime sector because of the stricter environmental regulations (SOx,NOx in the shipping industry. The battery-powered vehicle is another example of an environmentally friendly solution. The afore-mentioned measures can be considered as “abatement“ necessary in order to limit CO2 impact. The study shows that there are significant differences in the environmental impact between transport systems and the corresponding drive-system or associated energy base. The polluter should pay, which is a common basic principle in economic research. The Emission Trading Scheme (ETS has been introduced in order to ensure a reduction in CO2 output – emissions come with a price tag. An overall view is necessary, both en-vironmental and economic impact must be reconciled (cf. Spangenberg - TQI. The future viability of the transport system as we know it may change significantly over time if new environmental requirements or e.g. CO2 taxes or ETS are introduced in the freight sector. The abatement of CO2 should be effected primarily through technological
Towards a world development of LNG market

International Nuclear Information System (INIS)

Anon.

2002-01-01

The world development of the LNG trade was the theme of the second workshop of the 7. summit of natural gas industry leaders. With the increasing development of the LNG industry, a world scale natural gas market is becoming possible and should replace the present day regional markets. This article analyzes the expected economic impacts of such a market. (J.S.)
Review of the Fuel Saving, Life Cycle GHG Emission, and Ownership Cost Impacts of Lightweighting Vehicles with Different Powertrains.

Science.gov (United States)

Luk, Jason M; Kim, Hyung Chul; De Kleine, Robert; Wallington, Timothy J; MacLean, Heather L

2017-08-01

The literature analyzing the fuel saving, life cycle greenhouse gas (GHG) emission, and ownership cost impacts of lightweighting vehicles with different powertrains is reviewed. Vehicles with lower powertrain efficiencies have higher fuel consumption. Thus, fuel savings from lightweighting internal combustion engine vehicles can be higher than those of hybrid electric and battery electric vehicles. However, the impact of fuel savings on life cycle costs and GHG emissions depends on fuel prices, fuel carbon intensities and fuel storage requirements. Battery electric vehicle fuel savings enable reduction of battery size without sacrificing driving range. This reduces the battery production cost and mass, the latter results in further fuel savings. The carbon intensity of electricity varies widely and is a major source of uncertainty when evaluating the benefits of fuel savings. Hybrid electric vehicles use gasoline more efficiently than internal combustion engine vehicles and do not require large plug-in batteries. Therefore, the benefits of lightweighting depend on the vehicle powertrain. We discuss the value proposition of the use of lightweight materials and alternative powertrains. Future assessments of the benefits of vehicle lightweighting should capture the unique characteristics of emerging vehicle powertrains.
40 CFR 80.594 - What are the pre-compliance reporting requirements for motor vehicle diesel fuel?

Science.gov (United States)

2010-07-01

... requirements for motor vehicle diesel fuel? 80.594 Section 80.594 Protection of Environment ENVIRONMENTAL... Requirements § 80.594 What are the pre-compliance reporting requirements for motor vehicle diesel fuel? (a... June 1, 2005, all refiners and importers planning to produce or import motor vehicle diesel fuel...
Emission factors of air pollutants from CNG-gasoline bi-fuel vehicles: Part I. Black carbon.

Science.gov (United States)

Wang, Yang; Xing, Zhenyu; Xu, Hui; Du, Ke

2016-12-01

Compressed natural gas (CNG) is considered to be a "cleaner" fuel compared to other fossil fuels. Therefore, it is used as an alternative fuel in motor vehicles to reduce emissions of air pollutants in transportation. To quantify "how clean" burning CNG is compared to burning gasoline, quantification of pollutant emissions under the same driving conditions for motor vehicles with different fuels is needed. In this study, a fleet of bi-fuel vehicles was selected to measure the emissions of black carbon (BC), carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NO x ) for driving in CNG mode and gasoline mode respectively under the same set of constant speeds and accelerations. Comparison of emission factors (EFs) for the vehicles burning CNG and gasoline are discussed. This part of the paper series reports BC EFs for bi-fuel vehicles driving on the real road, which were measured using an in situ method. Our results show that burning CNG will lead to 54%-83% reduction in BC emissions per kilometer, depending on actual driving conditions. These comparisons show that CNG is a cleaner fuel than gasoline for motor vehicles in terms of BC emissions and provide a viable option for reducing BC emissions cause by transportation. Copyright © 2016 Elsevier B.V. All rights reserved.
LNG, the way ahead

International Nuclear Information System (INIS)

Chabrelie, M.F.

2007-01-01

Despite the many obstacles producers must overcome, particularly to satisfy demand at the right time, LNG remains the pre-eminent option for ensuring the expansion of the world's gas industry. (author)
History of Significant Vehicle and Fuel Introductions in the United States

Energy Technology Data Exchange (ETDEWEB)

Shirk, Matthew [Idaho National Lab. (INL), Idaho Falls, ID (United States); Alleman, Teresa [National Renewable Energy Lab. (NREL), Golden, CO (United States); Melendez, Margo [National Renewable Energy Lab. (NREL), Golden, CO (United States); Thomas, John F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); West, Brian H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-09-01

This is one of a series of reports produced as a result of the Co-Optimization of Fuels & Engines (Co-Optima) project, a Department of Energy (DOE)-sponsored multi-agency project initiated to accelerate the introduction of affordable, scalable, and sustainable biofuels and high-efficiency, low-emission vehicle engines. The simultaneous fuels and vehicles research and development is designed to deliver maximum energy savings, emissions reduction, and on-road performance.
Gas and LNG pricing and trading hub in East Asia: An introduction

OpenAIRE

Shi, Xunpeng

2017-01-01

This paper summarizes the four papers in the special issues on ‘Gas and LNG pricing and trading hub in East Asia’. The papers examine lessons and experience from European hub development, other commodity, the Japanese history on developing of futures markets and inter-fuel substitution in East Asia. The papers finds that liquid futures market is the key to formulate benchmark prices while a well-developed spot market is the foundation; political will and strong leadership are required to over...
Greenhouse Gas and Noxious Emissions from Dual Fuel Diesel and Natural Gas Heavy Goods Vehicles.

Science.gov (United States)

Stettler, Marc E J; Midgley, William J B; Swanson, Jacob J; Cebon, David; Boies, Adam M

2016-02-16

Dual fuel diesel and natural gas heavy goods vehicles (HGVs) operate on a combination of the two fuels simultaneously. By substituting diesel for natural gas, vehicle operators can benefit from reduced fuel costs and as natural gas has a lower CO2 intensity compared to diesel, dual fuel HGVs have the potential to reduce greenhouse gas (GHG) emissions from the freight sector. In this study, energy consumption, greenhouse gas and noxious emissions for five after-market dual fuel configurations of two vehicle platforms are compared relative to their diesel-only baseline values over transient and steady state testing. Over a transient cycle, CO2 emissions are reduced by up to 9%; however, methane (CH4) emissions due to incomplete combustion lead to CO2e emissions that are 50-127% higher than the equivalent diesel vehicle. Oxidation catalysts evaluated on the vehicles at steady state reduced CH4 emissions by at most 15% at exhaust gas temperatures representative of transient conditions. This study highlights that control of CH4 emissions and improved control of in-cylinder CH4 combustion are required to reduce total GHG emissions of dual fuel HGVs relative to diesel vehicles.
40 CFR 80.527 - Under what conditions may motor vehicle diesel fuel subject to the 15 ppm sulfur standard be...

Science.gov (United States)

2010-07-01

... vehicle diesel fuel subject to the 15 ppm sulfur standard be downgraded to motor vehicle diesel fuel... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.527 Under what conditions may motor vehicle diesel fuel subject to the 15...
40 CFR 1051.650 - What special provisions apply for converting a vehicle to use an alternate fuel?

Science.gov (United States)

2010-07-01

... converting a vehicle to use an alternate fuel? 1051.650 Section 1051.650 Protection of Environment... vehicle to use an alternate fuel? A certificate of conformity is no longer valid for a vehicle if the... applies if such modifications are done to convert the vehicle to run on a different fuel type. Such...
LNG: a commodity in the making

International Nuclear Information System (INIS)

Chabrelie, M.F.

2006-01-01

Although still far from being a commodity, LNG is undoubtedly emerging as an essential vector for world gas expansion. The flexibility it procures in terms of supply is of prime importance for future market equilibrium. Despite a number of uncertainties and constraints liable to thwart the realisation of the most optimistic growth prospects, the LNG trade remains wedded to rapid growth of about 7%/year by 2020, boosting its share of world gas trade to some 38% by that horizon. (author)
LNG: a commodity in the making

Energy Technology Data Exchange (ETDEWEB)

Chabrelie, M.F

2006-07-01

Although still far from being a commodity, LNG is undoubtedly emerging as an essential vector for world gas expansion. The flexibility it procures in terms of supply is of prime importance for future market equilibrium. Despite a number of uncertainties and constraints liable to thwart the realisation of the most optimistic growth prospects, the LNG trade remains wedded to rapid growth of about 7%/year by 2020, boosting its share of world gas trade to some 38% by that horizon. (author)
LNG: a commodity in the making

International Nuclear Information System (INIS)

Chabrelie, M.F.

2006-01-01

Although still far being a commodity, LNG is undoubtedly emerging as an essential vector for world gas expansion. The flexibility it procures in terms of supply is of prime importance for future market equilibrium. Despite a number of uncertainties and constraints liable to thwart the realization of the most optimistic growth prospects, the LNG trade remains wedded to rapid growth of about 7% year by 2020, boosting its share of world gas trade to some 38% by that horizon. (author)
An Efficient Two-Objective Hybrid Local Search Algorithm for Solving the Fuel Consumption Vehicle Routing Problem

OpenAIRE

Rao, Weizhen; Liu, Feng; Wang, Shengbin

2016-01-01

The classical model of vehicle routing problem (VRP) generally minimizes either the total vehicle travelling distance or the total number of dispatched vehicles. Due to the increased importance of environmental sustainability, one variant of VRPs that minimizes the total vehicle fuel consumption has gained much attention. The resulting fuel consumption VRP (FCVRP) becomes increasingly important yet difficult. We present a mixed integer programming model for the FCVRP, and fuel consumption is ...
Refloating stranded gas. Floating LNG-factory to become the largest ship on the world seas; Gestrand gas vlot trekken. Drijvende LNG-fabriek wordt grootste schip op wereldzeeen

Energy Technology Data Exchange (ETDEWEB)

De Wit, P.

2010-09-15

Great effort is currently put in the upcoming construction of a gigantic floating LNG plant that will be deployed by Shell. The enormous vessel will be used for the production of gas fields that are so far away from the coast that it is uneconomical to bring the gas to land by means of gas pipes, where it is converted into liquid natural gas (LNG). According to recent plans the first floating LNG plant will be used at the Prelude gas field northwest of Australia. [Dutch] Momenteel wordt hard gewerkt aan de aanstaande bouw van een gigantisch drijvende LNG-fabriek die door Shell ingezet gaat worden. Het enorme vaartuig wordt gebruikt voor de productie van gasvelden die zo ver uit de kust liggen dat het oneconomisch is om het gas met pijpleidingen aan land te brengen om het daar om te zetten in vloeibaar aardgas, LNG. Volgens de huidige plannen wordt de eerste drijvende LNG-fabriek gebruikt voor het Prelude gasveld ten noord-westen van Australie.

40 CFR 80.524 - What sulfur content standard applies to motor vehicle diesel fuel downstream of the refinery or...

Science.gov (United States)

2010-07-01

... to motor vehicle diesel fuel downstream of the refinery or importer? 80.524 Section 80.524 Protection... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.524 What sulfur content standard...
48 CFR 970.5223-5 - DOE motor vehicle fleet fuel efficiency.

Science.gov (United States)

2010-10-01

... and Contract Clauses for Management and Operating Contracts 970.5223-5 DOE motor vehicle fleet fuel..., insert the following clause in contracts providing for Contractor management of the motor vehicle fleet... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false DOE motor vehicle fleet...
A comparative evaluation of energy storage systems for a fuel cell vehicle. Paper no. IGEC-1-142

International Nuclear Information System (INIS)

Marshall, J.; Kazerani, M.

2005-01-01

The widespread operation of internal combustion engine (ICE) vehicles has today become a great cause for concern due to the uncertainty of fossil fuel reserves, energy security issues, and numerous adverse environmental effects. Alternatives such as fuel cell vehicles, electric vehicles, hybrid vehicles, and biodiesel vehicles provide the possibility to ease some or all of these concerns. The fuel cell vehicle, however, offers an excellent combination of reducing ICE vehicle problems while maintaining the performance, driving range, and convenience that consumers require. This paper documents a comparative evaluation of an extremely important facet of the fuel cell vehicle: the energy storage system (ESS). Batteries and ultracapacitors, the two most common choices for an ESS, are compared qualitatively to illustrate the advantages and disadvantages of each. Also, a quantitative comparison is made to choose the best technology for a small fuel cell-powered SUV having the design objectives of high performance and high efficiency. Practical issues such as availability and cost are also considered. The results of the analysis indicate that a battery ESS provides the best combination of efficiency, performance, and cost for a present-day fuel cell vehicle design. Yet, if the anticipated cost reductions and improvements in the energy storage capabilities of ultracapacitors do occur, ultracapacitors will become a very strong contender for energy storage solutions of future fuel cell vehicles. (author)
Fuel Cells: A Real Option for Unmanned Aerial Vehicles Propulsion

OpenAIRE

González_Espasandín, Oscar; Leo Mena, Teresa de Jesus; Navarro Arevalo, Emilio

2013-01-01

The possibility of implementing fuel cell technology in Unmanned Aerial Vehicle (UAV) propulsion systems is considered. Potential advantages of the Proton Exchange Membrane or Polymer Electrolyte Membrane (PEMFC) and Direct Methanol Fuel Cells (DMFC), their fuels (hydrogen and methanol), and their storage systems are revised from technical and environmental standpoints. Some operating commercial applications are described. Main constraints for these kinds of fuel cells are analyzed in order t...
LNG REGASIFICATION TERMINALS ACCESS CAPACITY ANALYSIS FOR SECURITY OF EUROPEAN NATURAL GAS SUPPLY

Directory of Open Access Journals (Sweden)

Matija Veselić

2011-12-01

Full Text Available Increasing natural gas consumption, declining North Sea gas reserves, increased production costs and the deregulation of European gas and electricity markets have all combined to create new opportunities for LNG in Europe. In these circumstances, LNG represents an opportunity for many European countries to diversify their natural gas supply, while decreasing their dependence on Russian natural gas import at the same time. The largest exporters of LNG to Europe are Qatar, Algeria, Nigeria, Trinidad & Tobago, Egypt and Oman. Spain, Great Britain and France are the largest European importers of LNG. Spain has six LNG regasification terminals, followed by four in Great Britain, three in France, two in Italy and Turkey and finally Greece and Portugal with one terminal each. New LNG regasification terminals are currently under construction in Italy, Spain, Sweden and Netherlands. In addition, more than 30 new LNG terminal projects have been proposed around Europe. Italy plans to construct as many as 10 new regasification terminals, due to the strong orientation of its national energy policy towards LNG. Many European countries are strongly considering participating in the LNG chain for the first time, namely Albania, Cyprus, Ireland, Lithuania, Germany, Poland, Romania, Ukraine and Croatia. This paper focuses on a specific aspect of the LNG supply chain: the import facility (the paper is published in Croatian.
49 CFR 571.303 - Standard No. 303; Fuel system integrity of compressed natural gas vehicles.

Science.gov (United States)

2010-10-01

... compressed natural gas vehicles. 571.303 Section 571.303 Transportation Other Regulations Relating to... system integrity of compressed natural gas vehicles. S1. Scope. This standard specifies requirements for the integrity of motor vehicle fuel systems using compressed natural gas (CNG), including the CNG fuel...
Has the natural gas fueled bus any future?

International Nuclear Information System (INIS)

Riikonen, A.

2001-01-01

Helsinki City Transport has decided to operate public transport in the center of the city with tramways and gas-fuelled busses. The decision is that there will be about 100 natural gas fueled busses in Helsinki by the year 2003. European exhaust gas emission (NO x and particulates) regulations have tightened strongly during the past few years. The regulations have forced to search for new fuels by the side of development of diesel engines. Alcohols, in spite of favourable fuel properties, are too expensive, so the use of them needs large subsidies for transportation sector. Gaseous fuels, both LPG and natural gas are suitable fuels for Otto cycle-cycle engines. After the previous oil crisis the interest in gas-fuelled engines has steadily decreased, but at present it is increasing again because of the objectives to decrease emissions of heavy vehicles at the level of gasoline-fuelled vehicles, equipped with three-way catalyst. From the point of view of emissions natural gas and LPG are seen as equivalent alternatives. The price of LPG varies on the basis of demand and on the basis of the prices of other oil products. Refuelling of a vehicle and storage of LPG in liquid form in the tank of the vehicle is easier than refuelling and fuel storage of natural gas. Investments to refuelling equipment of LPG are only 20% of those of the natural gas refuelling systems. The problem of natural gas is also the fact that is not easy to carry in the vehicle. Even if natural gas is compressed to pressure of 200 bars, it requires six times larger tanks if the refuelling intervals are the same. Liquefaction of natural gas reduces the volume significantly, but this is complicated and hence expensive. The tank of a vehicle should be vacuum insulated because the temperature of the LNG is about 160 deg C. Tank volume of LPG is only about twice that of diesel oil. Safety of natural gas is high, because it is lighter than the air, nearly a half of the density of the air. Octane ratings
Optimization of a fuel cell powertrain for a sport utility vehicle. Paper no. IGEC-1-087

International Nuclear Information System (INIS)

Stevens, M.B.; Mendes, C.; Mali, T.J.; Fowler, M.W.; Fraser, R.A.

2005-01-01

A central composite design was utilized to study the effects of fuel cell powertrain sizing and efficiencies on vehicle performance based on a Chevrolet Equinox platform. Simulations were performed using the Powertrain System Analysis Toolkit (PSAT), a vehicle simulator that constructs and executes various Simulink vehicle models. Once parametric equations relating performance metrics and subcomponent sizing and efficiency were fit, optimal design points were obtained using non-linear optimization. Optimized architectures were used to compare fuel cell powertrains incorporating ultracapacitors, nickel-metal hydride battery packs, and lithium-ion battery packs. The performance metrics also provided a basis for comparison with conventional, battery, and hybrid configurations. The fuel cell configurations exhibited similar or improved acceleration performance, with approximately double the mileage of the stock vehicle. The range of the fuel cell Equinox was reduced from the stock vehicle to approximately 300 miles. The battery vehicles showed the highest efficiencies and mileages, but exhibited an unacceptable range of approximately 100 miles. The hybrid configuration showed notable improvements over the stock vehicle, but still lacked the degree of benefits provided by the fuel cell (FCVs) and battery electric vehicles (BEVs). Also, the acceleration time for the hybrid vehicle was sluggish, likely due to the increase weight of the configuration. The work described in this study was performed by members of the University Of Waterloo Alternate Fuels Team (UWAFT) as part of the Challenge X Vehicle Competition. (author)
Design incentives to increase vehicle size created from the U.S. footprint-based fuel economy standards

International Nuclear Information System (INIS)

Whitefoot, Kate S.; Skerlos, Steven J.

2012-01-01

The recently amended U.S. Corporate Average Fuel Economy (CAFE) standards determine fuel-economy targets based on the footprint (wheelbase by track width) of vehicles such that larger vehicles have lower fuel-economy targets. This paper considers whether these standards create an incentive for firms to increase vehicle size by presenting an oligopolistic-equilibrium model in which automotive firms can modify vehicle dimensions, implement fuel-saving technology features, and trade off acceleration performance and fuel economy. Wide ranges of scenarios for consumer preferences are considered. Results suggest that the footprint-based CAFE standards create an incentive to increase vehicle size except when consumer preference for vehicle size is near its lower bound and preference for acceleration is near its upper bound. In all other simulations, the sales-weighted average vehicle size increases by 2–32%, undermining gains in fuel economy by 1–4 mpg (0.6–1.7 km/L). Carbon-dioxide emissions from these vehicles are 5–15% higher as a result (4.69×10 11 –5.17×10 11 kg for one year of produced vehicles compared to 4.47×10 11 kg with no size changes), which is equivalent to adding 3–10 coal-fired power plants to the electricity grid each year. Furthermore, results suggest that the incentive is larger for light trucks than for passenger cars, which could increase traffic safety risks. - Highlights: ► New U.S. fuel-economy standards may create an incentive to increase vehicle size. ► We model firms as choosing vehicle designs and prices in oligopolistic equilibrium. ► Vehicle size increases 2–32% for 20 out of 21 scenarios of consumer preferences. ► Increases in size reduce fuel economy gains from 5–13%, resulting in 5–15% higher CO 2 emissions. ► Incentive is larger for trucks than cars, which may increase traffic safety risks.
A techno-economic analysis of decentralized electrolytic hydrogen production for fuel cell vehicles

International Nuclear Information System (INIS)

Prince-Richard, S.; Whale, M.; Djilali, N.

2000-01-01

Fueling is a central issue in the development of fuel cell systems, especially for transportation applications. Which fuels will be used to provide the necessary hydrogen and what kind of production / distribution infrastructure will be required are key questions for the large scale market penetration of fuel cell vehicles. Methanol, gasoline and hydrogen are currently the three most seriously considered fuel options. Primarily because of economic considerations, these energy currencies would all be largely produced from fossil fuel sources in the near future. One problem in using fossil fuel sources as a feedstock is their associated emissions, in particular greenhouse gases. This paper presents some elements of a study currently underway to assess the techno-economic prospects of decentralized electrolytic hydrogen production for fuel cell vehicles
Thermodynamic and heat transfer analysis of LNG energy recovery for power production

International Nuclear Information System (INIS)

Franco, A; Casarosa, C

2014-01-01

An important option to transport the gas is to convert it into liquid natural gas (LNG) and convey it using insulated LNG tankers. At receiving terminals, the LNG is offloaded into storage tanks and then pumped at the required pressure and vaporized for final transmission to the pipeline. The LNG production process consumes a considerable amount of energy, while the cold availability, as also known as cold energy, has been stored in LNG. At a receiving terminal, LNG needs to be evaporated into gas at environmental temperature before fed into the gas distribution system. Seawater is commonly used for the regasification process of the LNG. In the present paper, after a general analysis of the perspectives of the various thermodynamic schemes proposed for power production from the regasification, a detailed analysis of enhanced direct expansion system is carried out in order to identify the upper level of the energy that can be recovered. The analysis outlines that power production typical of optimized ORC plant configurations (120 kJ/kg) can be obtained with direct expansion solutions
Thermodynamic and heat transfer analysis of LNG energy recovery for power production

Science.gov (United States)

Franco, A.; Casarosa, C.

2014-11-01

An important option to transport the gas is to convert it into liquid natural gas (LNG) and convey it using insulated LNG tankers. At receiving terminals, the LNG is offloaded into storage tanks and then pumped at the required pressure and vaporized for final transmission to the pipeline. The LNG production process consumes a considerable amount of energy, while the cold availability, as also known as cold energy, has been stored in LNG. At a receiving terminal, LNG needs to be evaporated into gas at environmental temperature before fed into the gas distribution system. Seawater is commonly used for the regasification process of the LNG. In the present paper, after a general analysis of the perspectives of the various thermodynamic schemes proposed for power production from the regasification, a detailed analysis of enhanced direct expansion system is carried out in order to identify the upper level of the energy that can be recovered. The analysis outlines that power production typical of optimized ORC plant configurations (120 kJ/kg) can be obtained with direct expansion solutions.
The LNG Industry - 2012

International Nuclear Information System (INIS)

2013-04-01

The 2011 catastrophic tsunami in Japan continued its grip on LNG flows throughout 2012, causing massive shifts eastwards of Atlantic Basin and Middle East-sourced cargoes to satisfy the strong demand of Japan's power industry. Its commercial effects are likely to continue beyond the current year as well as beyond a mere diversion of product flows. On the production side, capacity additions have been below expectations and insufficient to make up for the higher loss of capacity due to planned shutdowns and unscheduled production interruptions, mainly resulting from a shortfall of feed-gas. As a result, in 2012, LNG trade has seen the first decline (minus 1.9%) in the past thirty years. The strong growth in spot and short term trade seen in recent years (up by 110% from 2009 to 2011) is no longer there, primarily, but not solely, in line with the lack of new supplies. Undoubtedly, the conversion of non-committed production and flexible supplies and of so-called wedge cargoes -especially from Qatar and Peru- into term volumes has reduced the overall short term liquidity. Until substantial new volumes become available, this phenomenon is likely to continue for the next couple of years as Asian importers have a growing appetite for (more) secure supplies. Two events in 2012, albeit of a different nature, stand out among the highlights of the year: a significant rise in reloads, and the first final investment decision (FID) of exports from North America. Reloading of cargoes in receiving terminals is generally presented as a demonstration of commercial innovation though sometimes simply allowing to overcome destination restrictions or difficult negotiations on profit sharing from cargo deviations. Considering operational cost efficiency and the environmental impact, it is doubtful that reloads will continue to be a growing feature in LNG trading, despite a total count in 2012 of 70 re-exported cargoes actually discharged in 2012 (up 60% from last year). It is
A Choice Experiment on Alternative Fuel Vehicle Preferences of Private Car Owners in the Netherlands

NARCIS (Netherlands)

Hoen, A.; Koetse, M.J.

2014-01-01

This paper presents results of an online stated choice experiment on preferences of Dutch private car owners for alternative fuel vehicles (AFVs) and their characteristics. Results show that negative preferences for alternative fuel vehicles are large, especially for the electric and fuel cell car,
Distributed energy resources management using plug-in hybrid electric vehicles as a fuel-shifting demand response resource

DEFF Research Database (Denmark)

Morais, Hugo; Sousa, Tiago; Soares, J.

2015-01-01

In the smart grids context, distributed energy resources management plays an important role in the power systems' operation. Battery electric vehicles and plug-in hybrid electric vehicles should be important resources in the future distribution networks operation. Therefore, it is important...... to develop adequate methodologies to schedule the electric vehicles' charge and discharge processes, avoiding network congestions and providing ancillary services.This paper proposes the participation of plug-in hybrid electric vehicles in fuel shifting demand response programs. Two services are proposed......, namely the fuel shifting and the fuel discharging. The fuel shifting program consists in replacing the electric energy by fossil fuels in plug-in hybrid electric vehicles daily trips, and the fuel discharge program consists in use of their internal combustion engine to generate electricity injecting...
78 FR 32223 - Control of Air Pollution From Motor Vehicles: Tier 3 Motor Vehicle Emission and Fuel Standards

Science.gov (United States)

2013-05-29

...-OAR-2011-0135; FRL-9818-5] RIN 2060-A0 Control of Air Pollution From Motor Vehicles: Tier 3 Motor... extension of the public comment period for the proposed rule ``Control of Air Pollution from Motor Vehicles: Tier 3 Motor Vehicle Emission and Fuel Standards'' (the proposed rule is hereinafter referred to as...
Distributed energy resources management using plug-in hybrid electric vehicles as a fuel-shifting demand response resource

International Nuclear Information System (INIS)

Morais, H.; Sousa, T.; Soares, J.; Faria, P.; Vale, Z.

2015-01-01

Highlights: • Definition fuel shifting demand response programs applied to the electric vehicles. • Integration of the proposed fuel shifting in energy resource management algorithm. • Analysis of fuel shifting contribution to support the consumption increasing. • Analysis of fuel shifting contribution to support the electric vehicles growing. • Sensitivity analysis considering different electric vehicles penetration levels. - Abstract: In the smart grids context, distributed energy resources management plays an important role in the power systems’ operation. Battery electric vehicles and plug-in hybrid electric vehicles should be important resources in the future distribution networks operation. Therefore, it is important to develop adequate methodologies to schedule the electric vehicles’ charge and discharge processes, avoiding network congestions and providing ancillary services. This paper proposes the participation of plug-in hybrid electric vehicles in fuel shifting demand response programs. Two services are proposed, namely the fuel shifting and the fuel discharging. The fuel shifting program consists in replacing the electric energy by fossil fuels in plug-in hybrid electric vehicles daily trips, and the fuel discharge program consists in use of their internal combustion engine to generate electricity injecting into the network. These programs are included in an energy resources management algorithm which integrates the management of other resources. The paper presents a case study considering a 37-bus distribution network with 25 distributed generators, 1908 consumers, and 2430 plug-in vehicles. Two scenarios are tested, namely a scenario with high photovoltaic generation, and a scenario without photovoltaic generation. A sensitivity analyses is performed in order to evaluate when each energy resource is required
The LNG Industry in 2011

International Nuclear Information System (INIS)

Robin, Jean-Yves; Demoury, Vincent; Vermeire, Jean

2012-01-01

The most significant event to mark the LNG trade in 2011 has been the catastrophe that hit Japan in March, in view of both its short-term effect on shifting flows and its long-term demand prospects of LNG as a source for gas-fired power generation. The role of LNG as a flexible and secure energy source as well as the prompt response to provide back-up through additional supplies and cargo diversions to compensate for the sudden loss of nuclear capacity in Japan - with sellers exercising due price restraint in view of the human tragedy - has been a credit to the industry. The increase in production capacity in 2009 and 2010, in particular from Qatar, had permitted the necessary buffer to cope much better with the demand surge than during past disruptions (such as the aftermath of the Chuetsu earthquake in late 2007). Undoubtedly, the marked shift over the last decade in the industry's prevailing business model towards global trade, destination flexibility and portfolio play has also facilitated the rapid response. As the total volume of LNG trade is very much determined by the availability of supply, 2011 has seen a growth of 9.4% over 2010, mainly as a result of the full availability of the six Qatar mega-trains over the past year. On the demand side the two traditional basins have shown a very contrasting trend: 15% higher LNG off-take in Asia (the five major markets all increasing between 37.4% and 8.9%), versus a 1.7% decrease in the Atlantic Basin. Cargo diversions and an increasing number of reloads have boosted the exports from the Atlantic Basin to Asia in 2011 to more than 14 million tons (equivalent to more than 200 large size cargoes). Remarkable is also the fast growth in new markets in Latin America and in the Middle East - albeit from a small base - with counter-seasonal but varying demand, offering attractive arbitrage opportunities to portfolio play. Not surprising then that 2011 has seen another hike in spot and short-term trade, not just in
LNG pool fire spectral data and calculation of emissive power

International Nuclear Information System (INIS)

Raj, Phani K.

2007-01-01

Spectral description of thermal emission from fires provides a fundamental basis on which the fire thermal radiation hazard assessment models can be developed. Several field experiments were conducted during the 1970s and 1980s to measure the thermal radiation field surrounding LNG fires. Most of these tests involved the measurement of fire thermal radiation to objects outside the fire envelope using either narrow-angle or wide-angle radiometers. Extrapolating the wide-angle radiometer data without understanding the nature of fire emission is prone to errors. Spectral emissions from LNG fires have been recorded in four test series conducted with LNG fires on different substrates and of different diameters. These include the AGA test series of LNG fires on land of diameters 1.8 and 6 m, 35 m diameter fire on an insulated concrete dike in the Montoir tests conducted by Gaz de France, a 1976 test with 13 m diameter and the 1980 tests with 10 m diameter LNG fire on water carried out at China Lake, CA. The spectral data from the Montoir test series have not been published in technical journals; only recently has some data from this series have become available. This paper presents the details of the LNG fire spectral data from, primarily, the China Lake test series, their analysis and results. Available data from other test series are also discussed. China Lake data indicate that the thermal radiation emission from 13 m diameter LNG fire is made up of band emissions of about 50% of energy by water vapor (band emission), about 25% by carbon dioxide and the remainder constituting the continuum emission by luminous soot. The emissions from the H 2 O and CO 2 bands are completely absorbed by the intervening atmosphere in less than about 200 m from the fire, even in the relatively dry desert air. The effective soot radiation constitutes only about 23% during the burning period of methane and increases slightly when other higher hydrocarbon species (ethane, propane, etc.) are
Alternative Fuels Data Center: How Do Bi-fuel Natural Gas Vehicles Work?

Science.gov (United States)

power vehicle electronics/accessories. Electronic control module (ECM) - (gasoline): The ECM controls ; safeguards the engine from abuse; and detects and troubleshoots problems. Electronic control module (ECM sensors: These monitor the pressure of the fuel supply and relay that information to the electronic

77 FR 76013 - Sempra LNG Marketing, LLC; Application for Blanket Authorization To Export Previously Imported...

Science.gov (United States)

2012-12-26

... marketing supplies of LNG. Sempra is a customer of the Cameron Terminal. On June 22, 2012, FE issued DOE/FE... DEPARTMENT OF ENERGY [FE Docket No. 12-155-LNG] Sempra LNG Marketing, LLC; Application for Blanket..., by Sempra LNG Marketing, LLC (Sempra LNG Marketing), requesting blanket authorization to export...
Refueling Behavior of Flexible Fuel Vehicle Drivers in the Federal Fleet

Energy Technology Data Exchange (ETDEWEB)

Daley, R.; Nangle, J.; Boeckman, G.; Miller, M.

2014-05-01

Federal fleets are a frequent subject of legislative and executive efforts to lead a national transition to alternative fuels and advanced vehicle technologies. Section 701 of the Energy Policy Act of 2005 requires that all dual-fueled alternative fuel vehicles in the federal fleet be operated on alternative fuel 100% of the time when they have access to it. However, in Fiscal Year (FY) 2012, drivers of federal flex fuel vehicles (FFV) leased through the General Services Administration refueled with E85 24% of the time when it was available--falling well short of the mandate. The U.S. Department of Energy's National Renewable Energy Laboratory completed a 2-year Laboratory Directed Research and Development project to identify the factors that influence the refueling behavior of federal FFV drivers. The project began with two primary hypotheses. First, information scarcity increases the tendency to miss opportunities to purchase E85. Second, even with perfect information, there are limits to how far drivers will go out of their way to purchase E85. This paper discusses the results of the project, which included a June 2012 survey of federal fleet drivers and an empirical analysis of actual refueling behavior from FY 2009 to 2012. This research will aid in the design and implementation of intervention programs aimed at increasing alternative fuel use and reducing petroleum consumption.
What are the environmental benefits of electric vehicles? A life cycle based comparison of electric vehicles with biofuels, hydrogen and fossil fuels

Energy Technology Data Exchange (ETDEWEB)

Jungmeier, Gerfried; Canella, Lorenza; Beermann, Martin; Pucker, Johanna; Koenighofer, Kurt [JOANNEUM RESEARCH Forschungsgesellschaft mbH, Graz (Austria)

2013-06-01

The Renewable Energy Directive aims reaching a share of 10% of renewable fuels in Europe in 2020. These renewable fuels are transportation biofuels, renewable electricity and renewable hydrogen. In most European countries transportation biofuels are already on the transportation fuel market in significant shares, e.g. in Austria 7% by blending bioethanol to gasoline and biodiesel to diesel. Electric vehicles can significantly contribute towards creating a sustainable, intelligent mobility and intelligent transportation systems. They can open new business opportunities for the transportation engineering sector and electricity companies. But the broad market introduction of electric vehicles is only justified due to a significant improvement of the environmental impact compared to conventional vehicles. This means that in addition to highly efficient electric vehicles and renewable electricity, the overall environmental impact in the life cycle - from building the vehicles and the battery to recycling at the end of its useful life - has to be limited to an absolute minimum. There is international consensus that the environmental effects of electric vehicles (and all other fuel options) can only be analysed on the basis of life cycle assessment (LCA) including the production, operation and the end of life treatment of the vehicles. The LCA results for different environmental effects e.g. greenhouse gas emissions, primary energy consumption, eutrophication will be presented in comparison to other fuels e.g. transportation biofuels, gasoline, natural gas and the key factors to maximize the environmental benefits will be presented. The presented results are mainly based on a national research projects. These results are currently compared and discussed with international research activities within the International Energy Agency (lEA) in the Implementing Agreement on Hybrid and Electric Vehicles (IA-HEV) in Task 19 ''Life Cycle Assessment of Electric Vehicles
Estimation of fuel loss due to idling of vehicles at a signalized intersection in Chennai, India

Science.gov (United States)

Vasantha Kumar, S.; Gulati, Himanshu; Arora, Shivam

2017-11-01

The vehicles while waiting at signalized intersections are generally found to be in idling condition, i.e., not switching off their vehicles during red times. This phenomenon of idling of vehicles during red times at signalized intersections may lead to huge economic loss as lot of fuel is consumed by vehicles when they are in idling condition. The situation may even be worse in countries like India as different vehicle types consume varying amount of fuel. Only limited studies have been reported on estimation of fuel loss due to idling of vehicles in India. In the present study, one of the busy intersections in Chennai, namely, Tidel Park Junction in Rajiv Gandhi salai was considered. Data collection was carried out in one approach road of the intersection during morning and evening peak hours on a typical working day by manually noting down the red timings of each cycle and the corresponding number of two-wheelers, three-wheelers, passenger cars, light commercial vehicles (LCV) and heavy motorized vehicles (HMV) that were in idling mode. Using the fuel consumption values of various vehicles types suggested by Central Road Research Institute (CRRI), the total fuel loss during the study period was found to be Rs. 4,93,849/-. The installation of red timers, synchronization of signals, use of non-motorized transport for short trips and public awareness are some of the measures which government need to focus to save the fuel wasted at signalized intersections in major cities of India.
A Study on BC Emission from Vehicles using Different Types of Fuel

Science.gov (United States)

Kim, K.; Son, J.; Kim, J.; Kim, S.; Park, G.; Sung, K.; Kim, I.; Chung, T.; Park, T.; Kang, S.; Ban, J.; Kim, J.; Hong, Y. D.; Woo, J. H.; Lee, T.

2017-12-01

Black carbon (BC) is an anthropogenic aerosol from fossil fuels, and biomass burning. It absorbs solar radiation, and heats the atmosphere leading 0.4W m-2 radiative forcing. BC is a particle that can cause serious effects on human body as well. Toxicological studies of black carbon suggests that BC may be an important carrier of toxic chemicals to human body. The recent researches show that one of the main precursor of BC is vehicle emission, but the inventory of BC emission rate from vehicle is inadequate in South Korea. This study tries to find differences of BC emission from different sizes of vehicles using different types of fuels. Fuels used in vehicles are gasoline, liquefied petroleum gas (LPG), and diesel. BC was directly measured from the tail pipe of vehicles using Aethalometer (AE33, Magee Scientific Corporation). This study was conducted in Transport Pollutant Research Center, National Institute of Environmental Research, South Korea. Measurement was progressed with the five different test modes of speeds. Speed modes includes 4.7, 17.3, 34.1, 65.4, and 97.3 km h-1. Emission rate of BC was high in the slowest speed mode, and showed decrease with increase of the speed of vehicles. Gasoline vehicles had the relatively higher emission rate of BC than the LPG vehicle, while the emission rate of BC for Diesel with DPF (Diesel Particle Filter) was observed to be the lowest.
Fuel taxes, motor vehicle emission standards and patents related to the fuel-efficiency and emissions of motor vehicles. Joint Meetings of Tax and Environment Experts

International Nuclear Information System (INIS)

Vollebergh, H.

2010-01-01

Contribution to the project on Taxation, Innovation and the Environment of OECD's Joint Meetings of Tax and Environment Experts. It studies the impacts of motor vehicle fuel taxes and mandatory fuel efficiency standards on relevant car-related innovation activity in selected car-producing countries.
Logistics and supply chain effectiveness measure areas in lng companies

Directory of Open Access Journals (Sweden)

2010-09-01

Full Text Available The article describes the issues of logistics and supply chain measures in companies. It considers different management systems in the area of production, which evolved from isolated production activities to business connected systems. There are performed three case studies - three examples of systems proposed and implemented in the LNG industry: I-MAC, ICIMS and PMS. Data gained from these systems are the basis to create effectiveness measures for LNG companies and LNG supply chains.
Emissions from Diesel and Gasoline Vehicles Fuelled by Fischer-Tropsch Fuels and Similar Fuels

DEFF Research Database (Denmark)

Larsen, Ulrik; Lundorff, Peter; Ivarsson, Anders

2007-01-01

and an alkylate fuel (Aspen), which was taken to be the ultimate formula of FT gasoline. FT based diesel generally showed good emission performance, whereas the FT based gasoline not necessary lead to lower emissions. On the other hand, the Aspen fuel did show many advantages for the emissions from the gasoline...... vehicles fuelled by Fischer Tropsch (FT) based diesel and gasoline fuel, compared to the emissions from ordinary diesel and gasoline. The comparison for diesel fuels was based on a literature review, whereas the gasoline comparison had to be based on our own experiments, since almost no references were...
Enhancement of energy performance in a boil-off gas re-liquefaction system of LNG carriers using ejectors

International Nuclear Information System (INIS)

Tan, Hongbo; Zhao, Qingxuan; Sun, Nannan; Li, Yanzhong

2016-01-01

Highlights: • An ejector-enhanced LNG boil-off gas (BOG) re-liquefaction system is proposed. • The new system has an improvement of 28% in COP over the existing system. • The specific energy consumption of the new system is reduced to 0.59 kW h/kg(BOG). • The power consumption of 754.1 kW is saved in the case study. - Abstract: An ejector-enhanced Liquefied Natural Gas (LNG) boil-off gas (BOG) re-liquefaction system is proposed to improve the energy efficiency of the existing system. In the new system, two ejectors are respectively used to reduce the energy loss in the expansion of the pressurized BOG and inject a part of fuel BOG into the compression system, and a recuperator is employed to recover the cold energy of the BOG exited from LNG tank. The performance improvement of the proposed system is analysed on the basis of the simulation in Aspen HYSYS. In the case of the re-liquefaction capacity of 4557.6 kg/h, the coefficient of performance (COP) and exergy efficiency can be increased by 28%, and the specific energy consumption (SEC) reduced from 0.756 to 0.59 kW h/kg(BOG) compared to the conventional BOG re-liquefaction system. Correspondingly, the power consumption of 754.1 kW is saved. This means that applying ejectors can effectively improve the energy efficiency of the existing BOG re-liquefaction system for LNG carriers.
A Novel Range-Extended Strategy for Fuel Cell/Battery Electric Vehicles.

Science.gov (United States)

Hwang, Jenn-Jiang; Hu, Jia-Sheng; Lin, Chih-Hong

2015-01-01

The range-extended electric vehicle is proposed to improve the range anxiety drivers have of electric vehicles. Conventionally, a gasoline/diesel generator increases the range of an electric vehicle. Due to the zero-CO2 emission stipulations, utilizing fuel cells as generators raises concerns in society. This paper presents a novel charging strategy for fuel cell/battery electric vehicles. In comparison to the conventional switch control, a fuzzy control approach is employed to enhance the battery's state of charge (SOC). This approach improves the quick loss problem of the system's SOC and thus can achieve an extended driving range. Smooth steering experience and range extension are the main indexes for development of fuzzy rules, which are mainly based on the energy management in the urban driving model. Evaluation of the entire control system is performed by simulation, which demonstrates its effectiveness and feasibility.
40 CFR 80.596 - How is a refinery motor vehicle diesel fuel volume baseline calculated?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false How is a refinery motor vehicle diesel... Requirements § 80.596 How is a refinery motor vehicle diesel fuel volume baseline calculated? (a) For purposes of this subpart, a refinery's motor vehicle diesel fuel volume baseline is calculated using the...
COOLCEP (cool clean efficient power): A novel CO2-capturing oxy-fuel power system with LNG (liquefied natural gas) coldness energy utilization

International Nuclear Information System (INIS)

Zhang, Na; Lior, Noam; Liu, Meng; Han, Wei

2010-01-01

A novel liquefied natural gas (LNG) fueled power plant is proposed, which has virtually zero CO 2 and other emissions and a high efficiency. The plant operates as a subcritical CO 2 Rankine-like cycle. Beside the power generation, the system provides refrigeration in the CO 2 subcritical evaporation process, thus it is a cogeneration system with two valued products. By coupling with the LNG evaporation system as the cycle cold sink, the cycle condensation process can be achieved at a temperature much lower than ambient, and high-pressure liquid CO 2 can be withdrawn from the cycle without consuming additional power. Two system variants are analyzed and compared, COOLCEP-S and COOLCEP-C. In the COOLCEP-S cycle configuration, the working fluid in the main turbine expands only to the CO 2 condensation pressure; in the COOLCEP-C cycle configuration, the turbine working fluid expands to a much lower pressure (near-ambient) to produce more power. The effects of some key parameters, the turbine inlet temperature and the backpressure, on the systems' performance are investigated. It was found that at the turbine inlet temperature of 900 o C, the energy efficiency of the COOLCEP-S system reaches 59%, which is higher than the 52% of the COOLCEP-C one. The capital investment cost of the economically optimized plant is estimated to be about 750 EUR/kWe and the payback period is about 8-9 years including the construction period, and the cost of electricity is estimated to be 0.031-0.034 EUR/kWh.
Overview study of LNG release prevention and control systems

Energy Technology Data Exchange (ETDEWEB)

Pelto, P.J.; Baker, E.G.; Holter, G.M.; Powers, T.B.

1982-03-01

The liquefied natural gas (LNG) industry employs a variety of release prevention and control techniques to reduce the likelihood and the consequences of accidental LNG releases. A study of the effectiveness of these release prevention and control systems is being performed. Reference descriptions for the basic types of LNG facilities were developed. Then an overview study was performed to identify areas that merit subsequent and more detailed analyses. The specific objectives were to characterize the LNG facilities of interest and their release prevention and control systems, identify possible weak links and research needs, and provide an analytical framework for subsequent detailed analyses. The LNG facilities analyzed include a reference export terminal, marine vessel, import terminal, peakshaving facility, truck tanker, and satellite facility. A reference description for these facilities, a preliminary hazards analysis (PHA), and a list of representative release scenarios are included. The reference facility descriptions outline basic process flows, plant layouts, and safety features. The PHA identifies the important release prevention operations. Representative release scenarios provide a format for discussing potential initiating events, effects of the release prevention and control systems, information needs, and potential design changes. These scenarios range from relatively frequent but low consequence releases to unlikely but large releases and are the principal basis for the next stage of analysis.
Estimated Bounds and Important Factors for Fuel Use and Consumer Costs of Connected and Automated Vehicles

Energy Technology Data Exchange (ETDEWEB)

Stephens, T. S. [Argonne National Lab. (ANL), Argonne, IL (United States); Gonder, Jeff [National Renewable Energy Lab. (NREL), Golden, CO (United States); Chen, Yuche [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lin, Z. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Liu, C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gohlke, D. [US Dept. of Energy, Washington, DC (United States)

2016-11-01

This report details a study of the potential effects of connected and automated vehicle (CAV) technologies on vehicle miles traveled (VMT), vehicle fuel efficiency, and consumer costs. Related analyses focused on a range of light-duty CAV technologies in conventional powertrain vehicles -- from partial automation to full automation, with and without ridesharing -- compared to today's base-case scenario. Analysis results revealed widely disparate upper- and lower-bound estimates for fuel use and VMT, ranging from a tripling of fuel use to decreasing light-duty fuel use to below 40% of today's level. This wide range reflects uncertainties in the ways that CAV technologies can influence vehicle efficiency and use through changes in vehicle designs, driving habits, and travel behavior. The report further identifies the most significant potential impacting factors, the largest areas of uncertainty, and where further research is particularly needed.
10 CFR 490.203 - Light Duty Alternative Fueled Vehicle Plan.

Science.gov (United States)

2010-01-01

... Efficiency and Renewable Energy, EE-33, 1000 Independence Ave., SW., Washington, DC 20585, or to such other... 10 Energy 3 2010-01-01 2010-01-01 false Light Duty Alternative Fueled Vehicle Plan. 490.203 Section 490.203 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM...
Assessing integrity and realiability of multicomposite LNG transfer hoses

NARCIS (Netherlands)

Weijde, G.D. van der; Putten, S. van der

2012-01-01

Reliable transfer systems are a key element in developing floating LNG and the small scale LNG market. Multi-composite hoses may prove to be a reliable and cost effective solution for offshore, near- and on-shore applications. TNO, the Dutch contract research organization, has executed an extensive
The role of Liquefied Natural Gas (LNG) in the European gas market

International Nuclear Information System (INIS)

Mahan, A.

2003-06-01

The purpose of this paper is to discuss the role that Liquefied Natural Gas (LNG) might play in the future EU gas market. LNG imports are not likely to have a place in the Netherlands soon, but they could make an important contribution to the volume and diversity of Europe's gas supplies. An important characteristic of LNG is its inherently high costs, throughout the whole chain, from the wellhead to the market. These costs are considerably higher than the costs of bringing oil to the market. Cost considerations, in combination with the rigidity of the gas market, have led to the use of long-term contracts as a basis for the business, as is the case for the long haul pipeline gas business. Costs have come down considerably and further cost reductions are 'in the pipeline'. While this does not alter the fundamentals of the business it has nonetheless helped to extend the reach of LNG. LNG from the Middle East to Europe has now become economically feasible. The high gas prices of recent years have further fuelled the expansion of the LNG business. Supported by a rapidly growing global economy at the turn of this century, many prospects are under development. The positive economic outlook has seen more speculative positioning in every segment of the LNG chain, while more vertical integration has been industry's response to market liberalisation. The more recent slowdown of the market economies has created a surplus of LNG, which is finding its way onto the markets through short-term and spot transactions. The short-term business will grow over the next few years as more LNG and shipping capacity comes on-stream. However, given underlying high costs and limited flexibility, it should be expected that new projects, currently under consideration, will only be developed on the basis of long-term contracts, thus returning to a balance between supply and demand. For these same reasons, LNG will not likely develop the same the liquidity as that of the oil market. The global
Guanabara Bay and Pecem LNG flexible metering systems

Energy Technology Data Exchange (ETDEWEB)

Torres, Vinicus Roberto C.; Carvalho, Gustavo L.A.; Bruel, Edson L.; Santana, Jose P.C. de; Vidal, Lud C.C.N. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2009-12-19

This work presents to the community the metering systems installed in the Liquefied Natural (LNG) Gas Flexible Terminals of the Pecem Port and Guanabara Bay. A brief description of the Terminals facilities and its operation is firstly made to provide a background of the systems discussed. Then, the LNG custody transfer metering system, the operational control metering system, the energy balance of the LNG transferring system and the Natural Gas custody transfer metering system - that are our systems of interest - are described in detail. It is intended to use the philosophy adopted in the Guanabara Bay and Pecem Flexible Terminals design as a standard to future installations, integrated with improvements brought by the operation experience that will be obtained in those terminals. (author)
Renewable Natural Gas Clean-up Challenges and Applications

Science.gov (United States)

2011-01-13

produced from digesters ─ Animal manure (dairy cows, swine ) ─ Waste water treatment facilities > Methane from Landfills > RNG produced from...LNG) for vehicle fuel ─Ft. Lewis — Anaerobic digestion of waste water for production of hydrogen as a fuel cell vehicle fuel ─SCRA * – Landfill gas...BE CLEANED- UP AND PLACED IN THE NATURAL GAS PIPELINE SYSTEM 6 GTI RNG Project Examples >Example GTI Projects: ─Gills Onions— Anaerobic
LNG cascading damage study. Volume I, fracture testing report.

Energy Technology Data Exchange (ETDEWEB)

Petti, Jason P.; Kalan, Robert J.

2011-12-01

As part of the liquefied natural gas (LNG) Cascading Damage Study, a series of structural tests were conducted to investigate the thermal induced fracture of steel plate structures. The thermal stresses were achieved by applying liquid nitrogen (LN{sub 2}) onto sections of each steel plate. In addition to inducing large thermal stresses, the lowering of the steel temperature simultaneously reduced the fracture toughness. Liquid nitrogen was used as a surrogate for LNG due to safety concerns and since the temperature of LN{sub 2} is similar (-190 C) to LNG (-161 C). The use of LN{sub 2} ensured that the tests could achieve cryogenic temperatures in the range an actual vessel would encounter during a LNG spill. There were four phases to this test series. Phase I was the initial exploratory stage, which was used to develop the testing process. In the Phase II series of tests, larger plates were used and tested until fracture. The plate sizes ranged from 4 ft square pieces to 6 ft square sections with thicknesses from 1/4 inches to 3/4 inches. This phase investigated the cooling rates on larger plates and the effect of different notch geometries (stress concentrations used to initiate brittle fracture). Phase II was divided into two sections, Phase II-A and Phase II-B. Phase II-A used standard A36 steel, while Phase II-B used marine grade steels. In Phase III, the test structures were significantly larger, in the range of 12 ft by 12 ft by 3 ft high. These structures were designed with more complex geometries to include features similar to those on LNG vessels. The final test phase, Phase IV, investigated differences in the heat transfer (cooling rates) between LNG and LN{sub 2}. All of the tests conducted in this study are used in subsequent parts of the LNG Cascading Damage Study, specifically the computational analyses.

Spot sale of uncommitted LNG from Middle East: Japan or the UK?

International Nuclear Information System (INIS)

Nikhalat-Jahromi, Hamed; Bell, Michael G.H.; Fontes, Dalila B.M.M.; Cochrane, Robert A.; Angeloudis, Panagiotis

2016-01-01

The importance of liquefied natural gas (LNG) is rising as demand for it grows rapidly and steadily due to growth in energy demand, the transition to a low carbon economy and the longer distances over which natural gas is now traded. Given its importance, this work proposes an optimization model that assists to decide on when and where LNG should be delivered by coordinating tanker type, assignment and routing, inventory management, contract obligations, arbitrage and uncommitted LNG. The model maximizes the profit mainly by taking advantage of price differences between different markets. The contributions of this work are twofold. First, following the analysis of expenses and revenues, a new mixed integer programming model for LNG liquefaction and shipping is proposed from a corporate finance perspective. Furthermore, a solution approach for it is implemented and tested. Second, the model is used to derive a short term trade policy for the Middle Eastern LNG producers regarding the spot sale of their uncommitted product to Japan or to the UK, namely to: dispatch to whichever market has the higher current spot price, regardless of the variability of the transport expenses. - Highlights: •The cash-flow of an LNG producer in operational planning is examined. •An LNG inventory routing problem for EBITDA maximization is formulated. •A project in Middle East for studying the spot sale of uncommitted LNG is created. •In sale to Japan and the UK the market with the higher price should be picked.
Real-world fuel use and gaseous emission rates for flex fuel vehicles operated on E85 versus gasoline.

Science.gov (United States)

Delavarrafiee, Maryam; Frey, H Christopher

2018-03-01

Flex fuel vehicles (FFVs) typically operate on gasoline or E85, an 85%/15% volume blend of ethanol and gasoline. Differences in FFV fuel use and tailpipe emission rates are quantified for E85 versus gasoline based on real-world measurements of five FFVs with a portable emissions measurement system (PEMS), supplemented chassis dynamometer data, and estimates from the Motor Vehicle Emission Simulator (MOVES) model. Because of inter-vehicle variability, an individual FFV may have higher nitrogen oxide (NO x ) or carbon monoxide (CO) emission rates on E85 versus gasoline, even though average rates are lower. Based on PEMS data, the comparison of tailpipe emission rates for E85 versus gasoline is sensitive to vehicle-specific power (VSP). For example, although CO emission rates are lower for all VSP modes, they are proportionally lowest at higher VSP. Driving cycles with high power demand are more advantageous with respect to CO emissions, but less advantageous for NO x . Chassis dynamometer data are available for 121 FFVs at 50,000 useful life miles. Based on the dynamometer data, the average difference in tailpipe emissions for E85 versus gasoline is -23% for NO x , -30% for CO, and no significant difference for hydrocarbons (HC). To account for both the fuel cycle and tailpipe emissions from the vehicle, a life cycle inventory was conducted. Although tailpipe NO x emissions are lower for E85 versus gasoline for FFVs and thus benefit areas where the vehicles operate, the life cycle NO x emissions are higher because the NO x emissions generated during fuel production are higher. The fuel production emissions take place typically in rural areas. Although there are not significant differences in the total HC emissions, there are differences in HC speciation. The net effect of lower tailpipe NO x emissions and differences in HC speciation on ozone formation should be further evaluated. Reported comparisons of flex fuel vehicle (FFV) tailpipe emission rates for E85 versus
Analysis of operational, institutional and international limitations for alternative fuel vehicles and technologies: Means/methods for implementing changes

Energy Technology Data Exchange (ETDEWEB)

1992-07-01

This project focused upon the development of an approach to assist public fleet managers in evaluating the characteristics and availability of alternative fuels (AF`s) and alternative fuel vehicles (AFV`s) that will serve as possible replacements for vehicles currently serving the needs of various public entities. Also of concern were the institutional/international limitations for alternative fuels and alternative fuel vehicles. The City of Detroit and other public agencies in the Detroit area were the particular focus for the activities. As the development and initial stages of use of alternative fuels and alternative fuel vehicles proceeds, there will be an increasing need to provide information and guidance to decision-makers regarding differences in requirements and features of these fuels and vehicles. There wig be true differences in requirements for servicing, managing, and regulating. There will also be misunderstanding and misperception. There have been volumes of data collected on AFV`S, and as technology is improved, new data is constantly added. There are not, however, condensed and effective sources of information for public vehicle fleet managers on vehicle and equipment sources, characteristics, performance, costs, and environmental benefits. While theoretical modeling of public fleet requirements has been done, there do not seem to be readily available ``practical``. There is a need to provide the best possible information and means to minimize the problems for introducing the effective use of alternative fuels and alternative fuel vehicles.
What Fleets Need to Know About Alternative Fuel Vehicle Conversions, Retrofits, and Repowers

Energy Technology Data Exchange (ETDEWEB)

Kelly, K.; Gonzales, J.

2017-10-02

Many fleet managers have opted to incorporate alternative fuels and advanced vehicles into their lineup. Original equipment manufacturers (OEMs) offer a variety of choices, and there are additional options offered by aftermarket companies. There are also a myriad of ways that existing vehicles can be modified to utilize alternative fuels and other advanced technologies. Vehicle conversions and retrofit packages, along with engine repower options, can offer an ideal way to lower vehicle operating costs. This can result in long term return on investment, in addition to helping fleet managers achieve emissions and environmental goals. This report summarizes the various factors to consider when pursuing a conversion, retrofit, or repower option.
What Fleets Need to Know About Alternative Fuel Vehicle Conversions, Retrofits, and Repowers

Energy Technology Data Exchange (ETDEWEB)

Kelly, Kay L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gonzales, John [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-10-17

Many fleet managers have opted to incorporate alternative fuels and advanced vehicles into their lineup. Original equipment manufacturers (OEMs) offer a variety of choices, and there are additional options offered by aftermarket companies. There are also a myriad of ways that existing vehicles can be modified to utilize alternative fuels and other advanced technologies. Vehicle conversions and retrofit packages, along with engine repower options, can offer an ideal way to lower vehicle operating costs. This can result in long term return on investment, in addition to helping fleet managers achieve emissions and environmental goals. This report summarizes the various factors to consider when pursuing a conversion, retrofit, or repower option.
A dispersion safety factor for LNG vapor clouds

Energy Technology Data Exchange (ETDEWEB)

Vílchez, Juan A. [TIPs – Trámites, Informes y Proyectos, SL, Llenguadoc 10, 08030 Barcelona (Spain); Villafañe, Diana [Centre d’Estudis del Risc Tecnològic (CERTEC), Universitat Politècnica de Catalunya, Diagonal 647, 08028 Barcelona, Catalonia (Spain); Casal, Joaquim, E-mail: joaquim.casal@upc.edu [Centre d’Estudis del Risc Tecnològic (CERTEC), Universitat Politècnica de Catalunya, Diagonal 647, 08028 Barcelona, Catalonia (Spain)

2013-02-15

Highlights: ► We proposed a new parameter: the dispersion safety factor (DSF). ► DSF is the ratio between the distance reached by the LFL and that reached by the visible cloud. ► The results for the DSF agree well with the evidence from large scale experiments. ► Two expressions have been proposed to calculate DSF as a function of H{sub R}. ► The DSF may help in indicating the danger of ignition of a LNG vapor cloud. -- Abstract: The growing importance of liquefied natural gas (LNG) to global energy demand has increased interest in the possible hazards associated with its storage and transportation. Concerning the event of an LNG spill, a study was performed on the relationship between the distance at which the lower flammability limit (LFL) concentration occurs and that corresponding to the visible contour of LNG vapor clouds. A parameter called the dispersion safety factor (DSF) has been defined as the ratio between these two lengths, and two expressions are proposed to estimate it. During an emergency, the DSF can be a helpful parameter to indicate the danger of cloud ignition and flash fire.
A dispersion safety factor for LNG vapor clouds

International Nuclear Information System (INIS)

Vílchez, Juan A.; Villafañe, Diana; Casal, Joaquim

2013-01-01

Highlights: ► We proposed a new parameter: the dispersion safety factor (DSF). ► DSF is the ratio between the distance reached by the LFL and that reached by the visible cloud. ► The results for the DSF agree well with the evidence from large scale experiments. ► Two expressions have been proposed to calculate DSF as a function of H R . ► The DSF may help in indicating the danger of ignition of a LNG vapor cloud. -- Abstract: The growing importance of liquefied natural gas (LNG) to global energy demand has increased interest in the possible hazards associated with its storage and transportation. Concerning the event of an LNG spill, a study was performed on the relationship between the distance at which the lower flammability limit (LFL) concentration occurs and that corresponding to the visible contour of LNG vapor clouds. A parameter called the dispersion safety factor (DSF) has been defined as the ratio between these two lengths, and two expressions are proposed to estimate it. During an emergency, the DSF can be a helpful parameter to indicate the danger of cloud ignition and flash fire
A Novel Range-Extended Strategy for Fuel Cell/Battery Electric Vehicles

Directory of Open Access Journals (Sweden)

Jenn-Jiang Hwang

2015-01-01

Full Text Available The range-extended electric vehicle is proposed to improve the range anxiety drivers have of electric vehicles. Conventionally, a gasoline/diesel generator increases the range of an electric vehicle. Due to the zero-CO2 emission stipulations, utilizing fuel cells as generators raises concerns in society. This paper presents a novel charging strategy for fuel cell/battery electric vehicles. In comparison to the conventional switch control, a fuzzy control approach is employed to enhance the battery’s state of charge (SOC. This approach improves the quick loss problem of the system’s SOC and thus can achieve an extended driving range. Smooth steering experience and range extension are the main indexes for development of fuzzy rules, which are mainly based on the energy management in the urban driving model. Evaluation of the entire control system is performed by simulation, which demonstrates its effectiveness and feasibility.
75 FR 51989 - Southern LNG Company, L.L.C.; Notice of Application

Science.gov (United States)

2010-08-24

... Company, L.L.C.; Notice of Application August 16, 2010. Take notice that on August 4, 2010, Southern LNG Company, L.L.C. (Southern LNG), Post Office Box 2563, Birmingham, Alabama 35202-2563, filed in the above.... Sheffield, Director--Rates and Regulatory, Southern LNG Company, L.L.C., 569 Brookwood Village, Suite 501...
Benefits of recent improvements in vehicle fuel economy.

Science.gov (United States)

2014-10-01

For the past several years, we have calculated (on a monthly basis) the average, sales-weighted fuel economy of all light-duty vehicles (cars, pickup trucks, vans, and SUVs) sold in : the U.S. The results indicate that, from October 2007 to September...
Increased LNG into North America may threaten northern/Arctic gas development

International Nuclear Information System (INIS)

Howard, P.

2006-01-01

Since 2000, liquefied natural gas (LNG) has attracted considerable attention in response to record high price, high demand and tight supply of natural gas. LNG trade is expected to be 18 per cent of North American gas supply by 2020. The natural gas market is also affected by demand dominated by gas-fired power generation. The balance between supply and demand, combined with external factors of economic upsets and weather, has resulted in a volatile market place. LNG can currently be landed in North American at prices that compete with the average continental well head price. In January 2006, there were more than 60 competing LNG regasification projects proposed to access the North American gas market. This presentation listed the proposed facilities to import LNG and emphasized the need for a comprehensive analysis of gas development, given the degree of uncertainty regarding significant investment in gas supply, demand, pipelines and LNG projects. While only a few of the proposed projects will actually be constructed, they will more than double the existing output by 2010. The many possible changes in regional marketplace conditions were discussed with particular attention to the effects on the economic viability of natural gas developments; the impacts of LNG imports on capacities and flows in natural gas pipeline corridors; and, the influence of increased natural gas supplies on local and regional prices. It was noted that since conventional resources in Canada and the United States have reached a plateau, the next logical supply sources are Alaska, the Beaufort Sea, the Mackenzie Delta and the Arctic Islands. However, the development of northern and Arctic gas resources may be delayed if the level of LNG imports is sufficient to fill the deficiency in supply and demand. tabs., figs
Quantifying the Effects of Idle-Stop Systems on Fuel Economy in Light-Duty Passenger Vehicles

Energy Technology Data Exchange (ETDEWEB)

Jeff Wishart; Matthew Shirk

2012-12-01

Vehicles equipped with idle-stop (IS) systems are capable of engine shut down when the vehicle is stopped and rapid engine re-start for the vehicle launch. This capability reduces fuel consumption and emissions during periods when the engine is not being utilized to provide propulsion or to power accessories. IS systems are a low-cost and fast-growing technology in the industry-wide pursuit of increased vehicle efficiency, possibly becoming standard features in European vehicles in the near future. In contrast, currently there are only three non-hybrid vehicle models for sale in North America with IS systems and these models are distinctly low-volume models. As part of the United States Department of Energy’s Advanced Vehicle Testing Activity, ECOtality North America has tested the real-world effect of IS systems on fuel consumption in three vehicle models imported from Europe. These vehicles were chosen to represent three types of systems: (1) spark ignition with 12-V belt alternator starter; (2) compression ignition with 12-V belt alternator starter; and (3) direct-injection spark ignition, with 12-V belt alternator starter/combustion restart. The vehicles have undergone both dynamometer and on-road testing; the test results show somewhat conflicting data. The laboratory data and the portion of the on-road data in which driving is conducted on a prescribed route with trained drivers produced significant fuel economy improvement. However, the fleet data do not corroborate improvement, even though the data show significant engine-off time. It is possible that the effects of the varying driving styles and routes in the fleet testing overshadowed the fuel economy improvements. More testing with the same driver over routes that are similar with the IS system-enabled and disabled is recommended. There is anecdotal evidence that current Environmental Protection Agency fuel economy test procedures do not capture the fuel economy gains that IS systems produce in real
Test experiences with the DaimlerChrysler: Fuel cell electric vehicle NECAR

Directory of Open Access Journals (Sweden)

Friedlmeier Gerardo

2002-01-01

Full Text Available The DalmlerChrysler fuel cell electric vehicle NECAR 4, a hydrogen-fueled zero-emission compact car based on the A-Class of Mercedes-Benz, is described. Test results obtained on the road and on the dynamometer are presented. These and other results show the high technological maturity reliability and durability already achieved with fuel cell technology.
Test experiences with the DaimlerChrysler: Fuel cell electric vehicle NECAR

OpenAIRE

Friedlmeier Gerardo; Friedrich J.; Panik F.

2002-01-01

The DalmlerChrysler fuel cell electric vehicle NECAR 4, a hydrogen-fueled zero-emission compact car based on the A-Class of Mercedes-Benz, is described. Test results obtained on the road and on the dynamometer are presented. These and other results show the high technological maturity reliability and durability already achieved with fuel cell technology.
Information report submitted by the Commission for European Affairs on the directive proposition by the European Parliament and the Council on the deployment on alternative fuels infrastructure- Nr 1126

International Nuclear Information System (INIS)

Savary, Gilles

2013-01-01

As clean fuels are facing three main obstacles (high vehicle cost, low consumer receptivity, and lack of charge ports and refuelling stations), this report discusses the context and the implications of a European directive which aims establishing constraining objectives for infrastructures dedicated to clean fuels as electricity, hydrogen and natural gas. The author presents this directive in relationship with the objective of development of low-carbon or de-carbonated transports through the use of electricity, hydrogen, bio-fuels, liquefied or compressed natural gas (LNG and CNG), liquefied petroleum gas (LPG), and in relationship with European connector harmonisation. He outlines the interest of the European initiative with respect to the French position: being ahead with the existence of a French plan for the development of the electric vehicle, France must not fall behind on the issue of connector system. Two strategies are proposed in conclusion
Implementation of the HNS Convention in the LNG Industry: Singularities, Stakes, Issues and GIIGNL Proposed Solutions

International Nuclear Information System (INIS)

2008-01-01

The International Group of Liquefied Natural Gas Importers (GIIGNL) is a non-profit organization founded in December of 1971. It is composed of 56 member companies from 18 different countries across the world and involved in the importation of Liquefied Natural Gas. The main objective of the GIIGNL is to promote the development of activities related to LNG: purchasing, importing, processing, transportation, handling, re-gasification and various uses of LNG. For this purpose, the GIIGNL is particularly involved in promoting the state-of-the art technology in the LNG industry, in communicating about the economic fundamentals of the industry, in enhancing facility operations, in diversifying contractual techniques, and in developing industry positions to be taken in international agencies. As a member of the IOPC Fund since June 2007, the GIIGNL prepared this LNG overview in order to offer a better understanding to state delegations about this specific product and its market and to contribute to the debate on the implementation of the HNS Convention. the first chapter constitutes an introduction to the LNG Industry: presentation of an LNG Chain, overview of the global LNG trade and its growth rate, type of contracts, LNG tankers and technical transportation constraints, liquefaction and re-gasification plants around the world. The second chapter focuses on some singularities of the LNG industry that differentiate LNG from other Hazardous and Noxious Substances: LNG, a clean and unique product and activity, high standards and firm regulations concerning security and maritime safety, high level of investment required for an LNG chain, DES and FOB, the fundamental Incoterms of LNG sales and purchase. The third chapter presents the HNS Convention as potentially applicable to the LNG market: a two tier compensation regime - a new perspective for the LNG industry, a potential impact on LNG sales and purchase agreements, the importance of global HNS ratification within LNG
Preliminary design for spent fuel canister handling systems in a canister transfer and installation vehicle

International Nuclear Information System (INIS)

Wendelin, T.; Suikki, M.

2008-12-01

The report presents a spent fuel canister transfer and installation vehicle. The vehicle is used for carrying the fuel canister into a disposal tunnel and installing it into a deposition hole. The report outlines basic requirements and a design for canister handling equipment used in a canister transfer and installation vehicle, a description regarding the operation and maintenance of the equipment, as well as a cost estimate. Specific vehicles will be manufactured for all canister types in order to minimize the height of the disposal tunnels. This report is only focused on a transfer and installation vehicle for OL1-2 fuel canisters. Detailed designing and selection of final components have not yet been carried out. The report also describes the vehicle's requirements for the structures of a repository system, as well as actions in possible malfunction or fault situations. The spent fuel canister is brought from an encapsulation plant by a canister lift down to the repository level. The fuel canister is driven from the canister lift by an automated guided vehicle onto a canister hoist at a canister loading station. The canister transfer and installation vehicle is waiting for the canister with its radiation shield in an upright position above the canister hoist. The hoist carries the canister upward until the vehicle's own lifting means grab hold of the canister and raise it up into the vehicle's radiation shield. This is followed by turning the radiation shield to a transport position and by closing it in a radiation-proof manner against a rear radiation shield. The vehicle is driven along the central tunnel into the disposal tunnel and parked on top of the deposition hole. The vehicle's radiation shield is turned to the upright position and the canister is lowered with the vehicle's hydraulic winches into a bentonite-lined deposition hole. The radiation shield is turned back to the transport position and the vehicle can be driven out of the disposal tunnel
Energy Management Strategies based on efficiency map for Fuel Cell Hybrid Vehicles

Energy Technology Data Exchange (ETDEWEB)

Feroldi, Diego; Serra, Maria; Riera, Jordi [Institut de Robotica i Informatica Industrial (CSIC-UPC), C. Llorens i Artigas 4, 08028 Barcelona (Spain)

2009-05-15

The addition of a fast auxiliary power source like a supercapacitor bank in fuel cell-based vehicles has a great potential because permits a significant reduction of the hydrogen consumption and an improvement of the vehicle efficiency. The Energy Management Strategies, commanding the power split between the power sources in the hybrid arrangement to fulfil the power requirement, perform a fundamental role to achieve this objective. In this work, three strategies based on the knowledge of the fuel cell efficiency map are proposed. These strategies are attractive due to the relative simplicity of the real time implementation and the good performance. The strategies are tested both in a simulation environment and in an experimental setup using a 1.2-kW PEM fuel cell. The results, in terms of hydrogen consumption, are compared with an optimal case, which is assessed trough an advantageous technique also introduced in this work and with a pure fuel cell vehicle as well. This comparative reveals high efficiency and good performance, allowing to save up to 26% of hydrogen in urban scenarios. (author)
The Sport-Utility Vehicle: Debating Fuel-Economy Standards in Thermodynamics

Science.gov (United States)

Mayer, Shannon

2008-01-01

This paper describes a debate about national fuel-economy standards for sport-utility vehicles (SUVs) used as a foundation for exploring a public policy issue in the physical science classroom. The subject of automobile fuel economy benefits from a familiarity with thermodynamics, specifically heat engines, and is therefore applicable to a broad…
A NOVEL PROCESS TO USE SALT CAVERNS TO RECEIVE SHIP BORNE LNG

Energy Technology Data Exchange (ETDEWEB)

Michael M. McCall; William M. Bishop; Marcus Krekel; James F. Davis; D. Braxton Scherz

2005-05-31

This cooperative research project validates use of man made salt caverns to receive and store the cargoes of LNG ships in lieu of large liquid LNG tanks. Salt caverns will not tolerate direct injection of LNG because it is a cryogenic liquid, too cold for contact with salt. This research confirmed the technical processes and the economic benefits of pressuring the LNG up to dense phase, warming it to salt compatible temperatures and then directly injecting the dense phase gas into salt caverns for storage. The use of salt caverns to store natural gas sourced from LNG imports, particularly when located offshore, provides a highly secure, large scale and lower cost import facility as an alternative to tank based LNG import terminals. This design can unload a ship in the same time as unloading at a tank based terminal. The Strategic Petroleum Reserve uses man made salt caverns to securely store large quantities of crude oil. Similarly, this project describes a novel application of salt cavern gas storage technologies used for the first time in conjunction with LNG receiving. The energy industry uses man made salt caverns to store an array of gases and liquids but has never used man made salt caverns directly in the importation of LNG. This project has adapted and expanded the field of salt cavern storage technology and combined it with novel equipment and processes to accommodate LNG importation. The salt cavern based LNG receiving terminal described in the project can be located onshore or offshore, but the focus of the design and cost estimates has been on an offshore location, away from congested channels and ports. The salt cavern based terminal can provide large volumes of gas storage, high deliverability from storage, and is simplified in operation compared to tank based LNG terminals. Phase I of this project included mathematical modeling that proved a salt cavern based receiving terminal could be built at lower capital cost, and would have significantly higher

Developments in the safe design of LNG tanks

Science.gov (United States)

Fulford, N. J.; Slatter, M. D.

The objective of this paper is to discuss how the gradual development of design concepts for liquefied natural gas (LNG) storage systems has helped to enhance storage safety and economy. The experience in the UK is compared with practice in other countries with similar LNG storage requirements. Emphasis is placed on the excellent record of safety and reliability exhibited by tanks with a primary metal container designed and constructed to approved standards. The work carried out to promote the development of new materials, fire protection, and monitoring systems for use in LNG storage is also summarized, and specific examples described from British Gas experience. Finally, the trends in storage tank design world-wide and options for future design concepts are discussed, bearing in mind planned legislation and design codes governing hazardous installations.
A Study on Vehicle Emission Factor Correction Based on Fuel Consumption Measurement

Science.gov (United States)

Wang, Xiaoning; Li, Meng; Peng, Bo

2018-01-01

The objective of this study is to address the problem of obvious differences between the calculated and measured emissions of pollutants from motor vehicle by using the existing "Environmental Impact Assessment Specification of Highway Construction Projects". First, a field study collects the vehicle composition ratio, speed, slope, fuel consumption and other essential data. Considering practical applications, the emission factors corresponding to 40km/h and 110km/h and 120km/h velocity are introduced by data fitting. Then, the emission factors of motor vehicle are revised based on the measured fuel consumption, and the pollutant emission modified formula was calculated and compared with the standard recommendation formula. The results show the error between calculated and measured values are within 5%, which can better reflect the actual discharge of the motor vehicle.
Qatar chooses Snam to market LNG in Europe

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that Qatar has chosen Italy's Snam SpA as its European partner to sell liquefied natural gas to Europe from a $4.8 billion joint venture project involving supergiant North offshore gas field. State owned Qatar General petroleum Corp. (QGPC) and Snam signed an agreement in Doha to create a joint company owned 65% by QGPC and the remainder by Snam. Italy's state electricity monopoly, ENEL, which is seeking Qatari gas a fuel for its power plants, may later acquire part of Snam's interest in the project. The joint venture will transport and market North LNG to Europe. Exports to Europe by Snam via Italy, to begin in 1997, are expected to be 283 bcf/year at first and may climb to 459 bcf/year, depending upon demand
The relationship between income and personal vehicle fuel efficiency and associated equity concerns for the fuel tax.

Science.gov (United States)

2011-03-01

The fuel tax, which is assessed on the physical amount of fuel purchased by the consumer, is the primary : means of funding roadway development at the state and national level. However, because it is assessed on a : gallon basis, drivers of vehicles ...
Fuel Cells: A Real Option for Unmanned Aerial Vehicles Propulsion

Science.gov (United States)

2014-01-01

The possibility of implementing fuel cell technology in Unmanned Aerial Vehicle (UAV) propulsion systems is considered. Potential advantages of the Proton Exchange Membrane or Polymer Electrolyte Membrane (PEMFC) and Direct Methanol Fuel Cells (DMFC), their fuels (hydrogen and methanol), and their storage systems are revised from technical and environmental standpoints. Some operating commercial applications are described. Main constraints for these kinds of fuel cells are analyzed in order to elucidate the viability of future developments. Since the low power density is the main problem of fuel cells, hybridization with electric batteries, necessary in most cases, is also explored. PMID:24600326
Fuel Cells: A Real Option for Unmanned Aerial Vehicles Propulsion

Directory of Open Access Journals (Sweden)

Óscar González-Espasandín

2014-01-01

Full Text Available The possibility of implementing fuel cell technology in Unmanned Aerial Vehicle (UAV propulsion systems is considered. Potential advantages of the Proton Exchange Membrane or Polymer Electrolyte Membrane (PEMFC and Direct Methanol Fuel Cells (DMFC, their fuels (hydrogen and methanol, and their storage systems are revised from technical and environmental standpoints. Some operating commercial applications are described. Main constraints for these kinds of fuel cells are analyzed in order to elucidate the viability of future developments. Since the low power density is the main problem of fuel cells, hybridization with electric batteries, necessary in most cases, is also explored.
Fuel cells: a real option for Unmanned Aerial Vehicles propulsion.

Science.gov (United States)

González-Espasandín, Óscar; Leo, Teresa J; Navarro-Arévalo, Emilio

2014-01-01

The possibility of implementing fuel cell technology in Unmanned Aerial Vehicle (UAV) propulsion systems is considered. Potential advantages of the Proton Exchange Membrane or Polymer Electrolyte Membrane (PEMFC) and Direct Methanol Fuel Cells (DMFC), their fuels (hydrogen and methanol), and their storage systems are revised from technical and environmental standpoints. Some operating commercial applications are described. Main constraints for these kinds of fuel cells are analyzed in order to elucidate the viability of future developments. Since the low power density is the main problem of fuel cells, hybridization with electric batteries, necessary in most cases, is also explored.
Waste Management's LNG Truck Fleet: Final Results

Energy Technology Data Exchange (ETDEWEB)

Chandler, K. [Battelle (US); Norton, P. [National Renewable Energy Laboratory (US); Clark, N. [West Virginia University (US)

2001-01-25

Waste Management, Inc., began operating a fleet of heavy-duty LNG refuse trucks at its Washington, Pennsylvania, facility. The objective of the project was to provide transportation professionals with quantitative, unbiased information on the cost, maintenance, operational, and emissions characteristics of LNG as one alternative to conventional diesel for heavy-duty trucking applications.
Guide to alternative fuel vehicle incentives and laws: September 1998

Energy Technology Data Exchange (ETDEWEB)

Riley, C.; O' Connor, K.

1998-12-22

This guide provides information in support of the National Clean Cities Program, which will assist one in becoming better informed about the choices and options surrounding the use of alternative fuels and the purchase of alternative fuel vehicles. The information printed in this guide is current as of September 15, 1998. For recent additions or more up-to-date information, check the Alternative Fuels Data Center Web site at http://www.afdc.doe.gov
TAFV Alternative Fuels and Vehicles Choice Model Documentation; TOPICAL

International Nuclear Information System (INIS)

Greene, D.L.

2001-01-01

A model for predicting choice of alternative fuel and among alternative vehicle technologies for light-duty motor vehicles is derived. The nested multinomial logit (NML) mathematical framework is used. Calibration of the model is based on information in the existing literature and deduction based on assuming a small number of key parameters, such as the value of time and discount rates. A spreadsheet model has been developed for calibration and preliminary testing of the model
Alternative fuels and advanced technology vehicles : issues in Congress

Science.gov (United States)

2009-02-13

Alternative fuels and advanced technology vehicles are seen by proponents as integral to improving urban air quality, decreasing dependence on foreign oil, and reducing emissions of greenhouse gases. However, major barriers especially economics curre...
COOLCEP (cool clean efficient power): A novel CO{sub 2}-capturing oxy-fuel power system with LNG (liquefied natural gas) coldness energy utilization

Energy Technology Data Exchange (ETDEWEB)

Zhang, Na; Han, Wei [Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190 (China); Lior, Noam [Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Philadelphia, PA 19104-6315 (United States); Liu, Meng [Division of Research and Environment Standardization, China National Institute of Standardization, Beijing 100080 (China)

2010-02-15

A novel liquefied natural gas (LNG) fueled power plant is proposed, which has virtually zero CO{sub 2} and other emissions and a high efficiency. The plant operates as a subcritical CO{sub 2} Rankine-like cycle. Beside the power generation, the system provides refrigeration in the CO{sub 2} subcritical evaporation process, thus it is a cogeneration system with two valued products. By coupling with the LNG evaporation system as the cycle cold sink, the cycle condensation process can be achieved at a temperature much lower than ambient, and high-pressure liquid CO{sub 2} can be withdrawn from the cycle without consuming additional power. Two system variants are analyzed and compared, COOLCEP-S and COOLCEP-C. In the COOLCEP-S cycle configuration, the working fluid in the main turbine expands only to the CO{sub 2} condensation pressure; in the COOLCEP-C cycle configuration, the turbine working fluid expands to a much lower pressure (near-ambient) to produce more power. The effects of some key parameters, the turbine inlet temperature and the backpressure, on the systems' performance are investigated. It was found that at the turbine inlet temperature of 900 C, the energy efficiency of the COOLCEP-S system reaches 59%, which is higher than the 52% of the COOLCEP-C one. The capital investment cost of the economically optimized plant is estimated to be about 750 EUR/kWe and the payback period is about 8-9 years including the construction period, and the cost of electricity is estimated to be 0.031-0.034 EUR/kWh. (author)
Navigation API Route Fuel Saving Opportunity Assessment on Large-Scale Real-World Travel Data for Conventional Vehicles and Hybrid Electric Vehicles: Preprint

Energy Technology Data Exchange (ETDEWEB)

Zhu, Lei [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Holden, Jacob [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gonder, Jeffrey D [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-12-06

The green routing strategy instructing a vehicle to select a fuel-efficient route benefits the current transportation system with fuel-saving opportunities. This paper introduces a navigation API route fuel-saving evaluation framework for estimating fuel advantages of alternative API routes based on large-scale, real-world travel data for conventional vehicles (CVs) and hybrid electric vehicles (HEVs). The navigation APIs, such Google Directions API, integrate traffic conditions and provide feasible alternative routes for origin-destination pairs. This paper develops two link-based fuel-consumption models stratified by link-level speed, road grade, and functional class (local/non-local), one for CVs and the other for HEVs. The link-based fuel-consumption models are built by assigning travel from a large number of GPS driving traces to the links in TomTom MultiNet as the underlying road network layer and road grade data from a U.S. Geological Survey elevation data set. Fuel consumption on a link is calculated by the proposed fuel consumption model. This paper envisions two kinds of applications: 1) identifying alternate routes that save fuel, and 2) quantifying the potential fuel savings for large amounts of travel. An experiment based on a large-scale California Household Travel Survey GPS trajectory data set is conducted. The fuel consumption and savings of CVs and HEVs are investigated. At the same time, the trade-off between fuel saving and time saving for choosing different routes is also examined for both powertrains.
Future of gas. LNG between feast and famine

Energy Technology Data Exchange (ETDEWEB)

Forbes, A.

2009-05-15

Between now and 2012, a new wave of LNG (liquid natural gas) supply will wash over markets, with Qatar accounting for half the growth as six new 'mega-trains' come on stream. It will arrive just as gas demand is being hit by the economic crisis. Beyond 2012, the situation will reverse, with growth constrained by lack of new supply. The LNG industry is facing a turbulent decade.
Evolving framework of the LNG industry: Expected growth and continuing importance of safety

International Nuclear Information System (INIS)

Kagiyama, Ichiro

1992-01-01

A major increase in LNG trade, expected from the 1990s onwards, is quite significant in that a new framework will be developed. These changes and developments may well prove to be some of the most notable that have ever occurred in the 30-year history of the LNG industry. All over the world, new buyers and sellers are entering the scene, while in Japan, small and medium-size businesses are switching to LNG. Transporters and LNG carriers are also expecting an increase in their numbers. We are about to see a wide-ranging diversification in terms of the geography and the size of the companies that deal with LNG. Safety continues to be the main issue in promoting the development of the LNG market. The wider the spread of LNG, the greater the need will be for further development of the systems and organizations for transferring safety technology and skills. In addition to enhancing safety, it will be necessary to seek harmony with the social environment. This paper discusses measures for the future based on the author's many years of experience, particularly in the field of receiving terminals
Induced motor vehicle travel from improved fuel efficiency and road expansion

Energy Technology Data Exchange (ETDEWEB)

Su Qing, E-mail: suq1@nku.edu [Department of Marketing, Economics and Sports Business, Northern Kentucky University, AST Center, Office 338, Nunn Drive, Highland Heights, KY 41099 (United States)

2011-11-15

This paper investigates the impact of improved fuel efficiency and road network expansion on motor vehicle travel using a system dynamic panel data estimator and panel data at the state level for the 2001-2008 period. Our model accounts for endogenous changes in fuel efficiency, congestion, fuel cost per mile, and vehicle stock. Our regression results suggest that the short run rebound effect is 0.0276 while the long run rebound effect is 0.11. The short run effect of road capacity per capita is 0.066 while the long run effect is 0.26. - Highlights: > We estimate two effects: the rebound effect and induced travel effect at the state level. > System dynamic panel data approach is used to address endogeneity issue. > In the period of 2001-2008, the rebound effect is 0.0276 in the short run and 0.11 in the long run. > Increase in road capacity induces motor vehicle travel. > Induced travel effect is 0. 0.066 in the short run and 0.26 in the long run.
Induced motor vehicle travel from improved fuel efficiency and road expansion

International Nuclear Information System (INIS)

Su Qing

2011-01-01

This paper investigates the impact of improved fuel efficiency and road network expansion on motor vehicle travel using a system dynamic panel data estimator and panel data at the state level for the 2001-2008 period. Our model accounts for endogenous changes in fuel efficiency, congestion, fuel cost per mile, and vehicle stock. Our regression results suggest that the short run rebound effect is 0.0276 while the long run rebound effect is 0.11. The short run effect of road capacity per capita is 0.066 while the long run effect is 0.26. - Highlights: → We estimate two effects: the rebound effect and induced travel effect at the state level. → System dynamic panel data approach is used to address endogeneity issue. → In the period of 2001-2008, the rebound effect is 0.0276 in the short run and 0.11 in the long run. → Increase in road capacity induces motor vehicle travel. → Induced travel effect is 0. 0.066 in the short run and 0.26 in the long run.
Alternative Fuel Vehicles: How Do They Really Measure Up?

Science.gov (United States)

similar to that of comparable gasoline vehicles. The publication is available in .pdf format through DOE's Alternative Fuels Data Center home page on the World Wide Web. For a hard copy, call the National Alternative
Routing strategies for efficient deployment of alternative fuel vehicles for freight delivery.

Science.gov (United States)

2017-02-01

With increasing concerns on environmental issues, recent research on Vehicle Routing Problems : (VRP) has added new factors such as greenhouse gas emissions and alternative fuel vehicles into : the models. In this report, we consider one such promisi...
Refueling Infrastructure for Alternative Fuel Vehicles: Lessons Learned for Hydrogen; Workshop Proceedings

Energy Technology Data Exchange (ETDEWEB)

Melaina, M. W.; McQueen, S.; Brinch, J.

2008-07-01

DOE sponsored the Refueling Infrastructure for Alternative Fuel Vehicles: Lessons Learned for Hydrogen workshop to understand how lessons from past experiences can inform future efforts to commercialize hydrogen vehicles. This report contains the proceedings from the workshop.

Methane-fueled vehicles: A promising market for coalbed methane

International Nuclear Information System (INIS)

Deul, M.

1993-01-01

The most acceptable alternative fuel for motor vehicles is compressed natural gas (CNG). An important potential source of such gas is coalbed methane, much of which is now being wasted. Although there are no technological impediments to the use of CNG it has not been adequately promoted for a variety of reasons: structural, institutional and for coalbed gas, legal. The benefits of using CNG fuel are manifold: clean burning, low cost, abundant, and usable in any internal combustion engine. Even though more than 30,000 CNG vehicles are now in use in the U.S.A., they are not readily available, fueling stations are not easily accessible, and there is general apathy on the part of the public because of negligence by such agencies as the Department of Energy, the Department of Transportation and the Environmental Protection Agency. The economic benefits of using methane are significant: 100,000 cubic feet of methane is equivalent to 800 gallons of gasoline. Considering the many millions of cubic feet methane wasted from coal mines conservation and use of this resource is a worthy national goal
[Life cycle assessment of the infrastructure for hydrogen sources of fuel cell vehicles].

Science.gov (United States)

Feng, Wen; Wang, Shujuan; Ni, Weidou; Chen, Changhe

2003-05-01

In order to promote the application of life cycle assessment and provide references for China to make the project of infrastructure for hydrogen sources of fuel cell vehicles in the near future, 10 feasible plans of infrastructure for hydrogen sources of fuel cell vehicles were designed according to the current technologies of producing, storing and transporting hydrogen. Then life cycle assessment was used as a tool to evaluate the environmental performances of the 10 plans. The standard indexes of classified environmental impacts of every plan were gotten and sensitivity analysis for several parameters were carried out. The results showed that the best plan was that hydrogen will be produced by natural gas steam reforming in central factory, then transported to refuelling stations through pipelines, and filled to fuel cell vehicles using hydrogen gas at last.
40 CFR 80.530 - Under what conditions can 500 ppm motor vehicle diesel fuel be produced or imported after May 31...

Science.gov (United States)

2010-07-01

... motor vehicle diesel fuel be produced or imported after May 31, 2006? 80.530 Section 80.530 Protection... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Temporary Compliance Option § 80.530 Under what conditions can 500 ppm motor vehicle diesel...
LNG development across Europe: Infrastructural and regulatory analysis

International Nuclear Information System (INIS)

Dorigoni, Susanna; Portatadino, Sergio

2008-01-01

In this paper, a cross-section infrastructural and regulatory analysis of the European LNG sector is presented. The LNG chain is maintained as being a good tool to enlarge the number of natural gas exporters to Europe, adding in this way to competition and to the achievement of the targets of the liberalisation process, which is a decrease in price for final customers and security of supply. The main reason for this is to be identified in the minor specificity of the regasification-plant-related investment compared with pipeline transportation. As a matter of fact, as the infrastructural analysis will show, the construction of new LNG receiving terminals is likely to bring about an increase in the number of importers fostering competition among them and shrinking their margins among the value chain. In this context, regulation is meant to play a key role in promoting investments without hindering competition. Nevertheless it is questionable whether LNG will be able to introduce competition beyond the European border (that is among producers) according to the forecasted supply and demand balance that is leading to a seller's market in the upstream sector. In this case, a huger part of the rent would go to the exporters leaving minor scope for competition down the European border. (author)
Total's LNG activities from Algeria to Yemen

International Nuclear Information System (INIS)

Vedrenne, J.P.

1997-01-01

In March 1995, further to an international tender, Total was awarded the leadership of the first LNG project in Yemen. On January 1997 Total announced the extension of the share-holding of the Yemen LNG Co. to include the companies with interests in the Marib area (Hunt-Exxon-Yukong). The Marib area will supply the gas to the future liquefaction plant. The ratification of these agreements confirms the role of Total as lead shareholder with 36% in the share-holding structure and guarantees gas supply from the Marib licence, operated by Hunt-Exxon. (author)
Reforming petroleum-based fuels for fuel cell vehicles : composition-performance relationships

International Nuclear Information System (INIS)

Kopasz, J. P.; Miller, L. E.; Ahmed, S.; Devlin, P. R.; Pacheco, M.

2001-01-01

Onboard reforming of petroleum-based fuels, such as gasoline, may help ease the introduction of fuel cell vehicles to the marketplace. Although gasoline can be reformed, it is optimized to meet the demands of ICEs. This optimization includes blending to increase the octane number and addition of oxygenates and detergents to control emissions. The requirements for a fuel for onboard reforming to hydrogen are quite different than those for combustion. Factors such as octane number and flame speed are not important; however, factors such as hydrogen density, catalyst-fuel interactions, and possible catalyst poisoning become paramount. In order to identify what factors are important in a hydrocarbon fuel for reforming to hydrogen and what factors are detrimental, we have begun a program to test various components of gasoline and blends of components under autothermal reforming conditions. The results indicate that fuel composition can have a large effect on reforming behavior. Components which may be beneficial for ICEs for their octane enhancing value were detrimental to reforming. Fuels with high aromatic and naphthenic content were more difficult to reform. Aromatics were also found to have an impact on the kinetics for reforming of paraffins. The effects of sulfur impurities were dependent on the catalyst. Sulfur was detrimental for Ni, Co, and Ru catalysts. Sulfur was beneficial for reforming with Pt catalysts, however, the effect was dependent on the sulfur concentration
Vehicle Routing Problems with Fuel Consumption and Stochastic Travel Speeds

Directory of Open Access Journals (Sweden)

Yanling Feng

2017-01-01

Full Text Available Conventional vehicle routing problems (VRP always assume that the vehicle travel speed is fixed or time-dependent on arcs. However, due to the uncertainty of weather, traffic conditions, and other random factors, it is not appropriate to set travel speeds to fixed constants in advance. Consequently, we propose a mathematic model for calculating expected fuel consumption and fixed vehicle cost where average speed is assumed to obey normal distribution on each arc which is more realistic than the existing model. For small-scaled problems, we make a linear transformation and solve them by existing solver CPLEX, while, for large-scaled problems, an improved simulated annealing (ISA algorithm is constructed. Finally, instances from real road networks of England are performed with the ISA algorithm. Computational results show that our ISA algorithm performs well in a reasonable amount of time. We also find that when taking stochastic speeds into consideration, the fuel consumption is always larger than that with fixed speed model.
Industry brief letter; Oman LNG, Indo no hatsuden mukeni kyokyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

Oman LNG (OLNG), invested by Mitui Bussan, Mitsubishi Trading and Itochu Trading, concluded a supply contract of liquefied natural gas with a private power supply enterprise of India. Contract period is 20 years, and supplies 1.6 million ton LNG per year from the fourth quarter of 2001. This is the third contract case following to Korea Gas of Korea and Osaka Gas of Japan. OLNG will establish annual production 6.6 million system by the end of 1999. With this contract, almost all LNG production will be ensured to be sold by long term contracts. (translated by NEDO)
China's fuel economy standards for passenger vehicles. Rationale, policy process, and impacts

International Nuclear Information System (INIS)

Oliver, Hongyan H.; Gallagher, Kelly Sims; Tian, Donglian; Zhang, Jinhua

2009-01-01

China issued its first Fuel Economy Standards (FES) for light-duty passenger vehicles (LDPV) in September 2004, and the first and second phases of the FES took effective in July 2005 and January 2008, respectively. The stringency of the Chinese FES ranks third globally, following the Japanese and European standards. In this paper, we first review the policy-making background, including the motivations, key players, and the process; and then explain the content and the features of the FES and why there was no compliance flexibility built into it. Next, we assess the various aspects of the standard's impact, including fuel economy improvement, technology changes, shift of market composition, and overall fuel savings. Lastly, we comment on the prospect of tightening the existing FES and summarize the complementary policies that have been adopted or may be considered by the Chinese government for further promoting efficient vehicles and reducing transport energy consumption. The Chinese experience is highly relevant for countries that are also experiencing or anticipating rapid growth in personal vehicles, those wishing to moderate an increase in oil demand, or those desirous of vehicle technology upgrades. (author)
A review on idling reduction strategies to improve fuel economy and reduce exhaust emissions of transport vehicles

International Nuclear Information System (INIS)

Shancita, I.; Masjuki, H.H.; Kalam, M.A.; Rizwanul Fattah, I.M.; Rashed, M.M.; Rashedul, H.K.

2014-01-01

Highlights: • Introduce various idling reduction technologies for transport vehicles. • Exhibit their energy use, advantages, disadvantages to understand their capability. • Conduct critical review to improve fuel economy and exhaust emissions. • Suggest better technology according to their performance ability. - Abstract: To achieve reductions in vehicle idling, strategies and actions must be taken to minimize the time spent by drivers idling their engines. A number of benefits can be obtained in limiting the idling time. These benefits include savings in fuel use and maintenance costs, vehicle life extension, and reduction in exhaust emissions. The main objective of idling reduction (IR) devices is to reduce the amount of energy wasted by idling trucks, rail locomotives, and automobiles. During idling, gasoline vehicles emit a minimum amount of nitrogen oxides (NO x ) and negligible particulate matter (PM). However, generally a large amount of carbon monoxide (CO) and hydrocarbons (HC) are produced from these vehicles. Gasoline vehicles consume far more fuel at an hourly rate than their diesel counterparts during idling. Higher NOx and comparatively larger PM are produced by diesel vehicles than gasoline vehicles on the average during idling. Auxiliary power unit (APU), direct-fired heaters, fuel cells, thermal storage system, truck stop electrification, battery-based systems, engine idle management (shutdown) systems, electrical (shore power) solutions, cab comfort system, and hybridization are some of the available IR technologies whose performances for reducing fuel consumption and exhaust emissions have been compared. This paper analyzes the availability and capability of most efficient technologies to reduce fuel consumption and exhaust emissions from diesel and gasoline vehicles by comparing the findings of previous studies. The analysis reveals that among all the options direct fired heaters, APUs and electrified parking spaces exhibit better
Emission factors of air pollutants from CNG-gasoline bi-fuel vehicles: Part II. CO, HC and NOx.

Science.gov (United States)

Huang, Xiaoyan; Wang, Yang; Xing, Zhenyu; Du, Ke

2016-09-15

The estimation of emission factors (EFs) is the basis of accurate emission inventory. However, the EFs of air pollutants for motor vehicles vary under different operating conditions, which will cause uncertainty in developing emission inventory. Natural gas (NG), considered as a "cleaner" fuel than gasoline, is increasingly being used to reduce combustion emissions. However, information is scarce about how much emission reduction can be achieved by motor vehicles burning NG (NGVs) under real road driving conditions, which is necessary for evaluating the environmental benefits for NGVs. Here, online, in situ measurements of the emissions from nine bi-fuel vehicles were conducted under different operating conditions on the real road. A comparative study was performed for the EFs of black carbon (BC), carbon monoxide (CO), hydrocarbons (HCs) and nitrogen oxides (NOx) for each operating condition when the vehicles using gasoline and compressed NG (CNG) as fuel. BC EFs were reported in part I. The part II in this paper series reports the influence of operating conditions and fuel types on the EFs of CO, HC and NOx. Fuel-based EFs of CO showed good correlations with speed when burning CNG and gasoline. The correlation between fuel-based HC EFs and speed was relatively weak whether burning CNG or gasoline. The fuel-based NOx EFs moderately correlated with speed when burning CNG, but weakly correlated with gasoline. As for HC, the mileage-based EFs of gasoline vehicles are 2.39-12.59 times higher than those of CNG vehicles. The mileage-based NOx EFs of CNG vehicles are slightly higher than those of gasoline vehicles. These results would facilitate a detailed analysis of the environmental benefits for replacing gasoline with CNG in light duty vehicles. Copyright © 2016 Elsevier B.V. All rights reserved.
75 FR 53688 - Southern LNG Company, L.L.C.; Notice of Technical Conference

Science.gov (United States)

2010-09-01

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. RP10-829-000] Southern LNG Company, L.L.C.; Notice of Technical Conference August 25, 2010. Take notice that Commission Staff will... Street, NE., Washington, DC 20426. On June 7, 2010, Southern LNG Company, L.L.C. (Southern LNG) filed a...
Modelling and design optimization of low speed fuel cell - battery hybrid electric vehicles. Paper no. IGEC-1-125

International Nuclear Information System (INIS)

Guenther, M.; Dong, Z.

2005-01-01

A push for electric vehicles has occurred in the past several decades due to various concerns about air pollution and the contribution of emissions to global climate change. Although electric cars and buses have been the focus of much of electric vehicle development, smaller vehicles are used extensively for transportation and utility purposes in many countries. In order to explore the viability of fuel cell - battery hybrid electric vehicles, empirical fuel cell system data has been incorporated into the NREL's vehicle design and simulation tool, ADVISOR (ADvanced Vehicle SimulatOR), to predict the performance of a low-speed, fuel cell - battery electric vehicle through MATLAB Simulink. The modelling and simulation provide valuable feedback to the design optimization of the fuel cell power system. A sampling based optimization algorithm was used to explore the viability and options of a low cost design for urban use. (author)
Purifier-integrated methanol reformer for fuel cell vehicles

Science.gov (United States)

Han, Jaesung; Kim, Il-soo; Choi, Keun-Sup

We developed a compact, 3-kW, purifier-integrated modular reformer which becomes the building block of full-scale 30-kW or 50-kW methanol fuel processors for fuel cell vehicles. Our proprietary technologies regarding hydrogen purification by composite metal membrane and catalytic combustion by washcoated wire-mesh catalyst were combined with the conventional methanol steam-reforming technology, resulting in higher conversion, excellent quality of product hydrogen, and better thermal efficiency than any other systems using preferential oxidation. In this system, steam reforming, hydrogen purification, and catalytic combustion all take place in a single reactor so that the whole system is compact and easy to operate. Hydrogen from the module is ultrahigh pure (99.9999% or better), hence there is no power degradation of PEMFC stack due to contamination by CO. Also, since only pure hydrogen is supplied to the anode of the PEMFC stack, 100% hydrogen utilization is possible in the stack. The module produces 2.3 Nm 3/h of hydrogen, which is equivalent to 3 kW when PEMFC has 43% efficiency. Thermal efficiency (HHV of product H 2/HHV of MeOH in) of the module is 89% and the power density of the module is 0.77 kW/l. This work was conducted in cooperation with Hyundai Motor Company in the form of a Korean national project. Currently the module is under test with an actual fuel cell stack in order to verify its performance. Sooner or later a full-scale 30-kW system will be constructed by connecting these modules in series and parallel and will serve as the fuel processor for the Korean first fuel cell hybrid vehicle.
Fuel Property, Emission Test, and Operability Results from a Fleet of Class 6 Vehicles Operating on Gas-to-Liquid Fuel and Catalyzed Diesel Particle Filters

Energy Technology Data Exchange (ETDEWEB)

Alleman, T. L.; Eudy, L.; Miyasato, M.; Oshinuga, A.; Allison, S.; Corcoran, T.; Chatterjee, S.; Jacobs, T.; Cherrillo, R. A.; Clark, R.; Virrels, I.; Nine, R.; Wayne, S.; Lansing, R.

2005-11-01

A fleet of six 2001 International Class 6 trucks operating in southern California was selected for an operability and emissions study using gas-to-liquid (GTL) fuel and catalyzed diesel particle filters (CDPF). Three vehicles were fueled with CARB specification diesel fuel and no emission control devices (current technology), and three vehicles were fueled with GTL fuel and retrofit with Johnson Matthey's CCRT diesel particulate filter. No engine modifications were made.
Waiting for the Next Train? An Assessment of the Emerging Canadian LNG Industry

International Nuclear Information System (INIS)

Hureau, Geoffroy; Jordan, Louis

2015-03-01

In February 2015, Canada counted 22 LNG liquefaction plant projects - of which 17 are located in British Columbia - representing a total design capacity of 325 mmtpa. Canada has the potential to become a major LNG exporter but no project has received Final Investment Decision (FID) so far. Competition with US brown field projects with innovative business models have limited the commercial appeal of many Canadian projects relying on oil indexing. More recently, plummeting oil prices have put into question their profitability and lead to several postponements of FID reviews. This paper discusses the potential for Canada to export LNG, looking at the initial enthusiasm and wide support by public authorities and local communities but also at the economic challenges and commercial issues that are slowing the progress of these projects. In 2013, Canada owned 2,028 Bcm of proved natural gas reserves and in 2012, remaining marketable gas resources were estimated to exceed 30,000 Bcm, located mainly in the Western Canada Sedimentary Basin. In 2013, natural gas consumption grew due to higher demand from the tar sands industry and reached 90 Bcm, while marketed production rebounded slightly to 145 Bcm after 10 years of continuous decline. Net exports to the United States, the only export market for Canadian gas, kept decreasing to 55 Bcm. In the future, consumption is expected to grow at a slower rate than production and net exports to the United States to keep declining. As a consequence, LNG appears to be an ideal solution to monetize gas and to unlock these large resources. However, CEDIGAZ does not expect material LNG exports to start before 2021, but they could reach 34 mmtpa by 2035. Since the very beginning of the wave of LNG project proposals, Canadian federal and provincial authorities have appeared very supportive. At the provincial level, the government of British Columbia has multiplied initiatives to favor the emergence of a LNG industry, including by lowering
Gasoline Ultra Efficient Fuel Vehicle with Advanced Low Temperature Combustion

Energy Technology Data Exchange (ETDEWEB)

Confer, Keith [Delphi Automotive Systems, LLC, Troy, MI (United States)

2014-12-18

The objective of this program was to develop, implement and demonstrate fuel consumption reduction technologies which are focused on reduction of friction and parasitic losses and on the improvement of thermal efficiency from in-cylinder combustion. The program was executed in two phases. The conclusion of each phase was marked by an on-vehicle technology demonstration. Phase I concentrated on short term goals to achieve technologies to reduce friction and parasitic losses. The duration of Phase I was approximately two years and the target fuel economy improvement over the baseline was 20% for the Phase I demonstration. Phase II was focused on the development and demonstration of a breakthrough low temperature combustion process called Gasoline Direct- Injection Compression Ignition (GDCI). The duration of Phase II was approximately four years and the targeted fuel economy improvement was 35% over the baseline for the Phase II demonstration vehicle. The targeted tailpipe emissions for this demonstration were Tier 2 Bin 2 emissions standards.
Evaluating the Impact of Road Grade on Simulated Commercial Vehicle Fuel Economy Using Real-World Drive Cycles

Energy Technology Data Exchange (ETDEWEB)

Lopp, Sean; Wood, Eric; Duran, Adam

2015-10-13

Commercial vehicle fuel economy is known to vary significantly with both positive and negative road grade. Medium- and heavy-duty vehicles operating at highway speeds require incrementally larger amounts of energy to pull heavy payloads up inclines as road grade increases. Non-hybrid vehicles are then unable to recapture energy on descent and lose energy through friction braking. While the on-road effects of road grade are well understood, the majority of standard commercial vehicle drive cycles feature no climb or descent requirements. Additionally, existing literature offers a limited number of sources that attempt to estimate the on-road energy implications of road grade in the medium- and heavy-duty space. This study uses real-world commercial vehicle drive cycles from the National Renewable Energy Laboratory's Fleet DNA database to simulate the effects of road grade on fuel economy across a range of vocations, operating conditions, and locations. Drive-cycles are matched with vocation-specific vehicle models and simulated with and without grade. Fuel use due to grade is presented, and variation in fuel consumption due to drive cycle and vehicle characteristics is explored through graphical and statistical comparison. The results of this study suggest that road grade accounts for 1%-9% of fuel use in commercial vehicles on average and up to 40% on select routes.
Effect Of Platooning on Fuel Consumption of Class 8 Vehicles Over a Range of Speeds, Following Distances, and Mass

Energy Technology Data Exchange (ETDEWEB)

Lammert, M. P.; Duran, A.; Diez, J.; Burton, K.; Nicholson, A.

2014-10-01

This research project evaluates fuel consumption results of two Class 8 tractor-trailer combinations platooned together compared to their standalone fuel consumption. A series of ten modified SAE Type II J1321 fuel consumption track tests were performed to document fuel consumption of two platooned vehicles and a control vehicle at varying steady-state speeds, following distances, and gross vehicle weights (GVWs). The steady-state speeds ranged from 55 mph to 70 mph, the following distances ranged from a 20-ft following distance to a 75-ft following distance, and the GVWs were 65K lbs and 80K lbs. All tractors involved had U.S. Environmental Protection Agency (EPA) SmartWay-compliant aerodynamics packages installed, and the trailers were equipped with side skirts. Effects of vehicle speed, following distance, and GVW on fuel consumption were observed and analyzed. The platooning demonstration system used in this study consisted of radar systems, Dedicated Short-Range Communication (DSRC) vehicle-to-vehicle (V2V) communications, vehicle braking and torque control interface, cameras and driver displays. The lead tractor consistently demonstrated an improvement in average fuel consumption reduction as following distance decreased, with results showing 2.7% to 5.3% fuel savings at a GVW of 65k. The trailing vehicle achieved fuel consumption savings ranging from 2.8% to 9.7%; tests during which the engine cooling fan did not operate achieved savings of 8.4% to 9.7%. 'Team' fuel savings, considering the platooned vehicles as one, ranged from 3.7% to 6.4%, with the best combined result being for 55 mph, 30-ft following distance, and 65k GVW.
LNG (Liquefied Natural Gas): emerging control; GNL (Gas Natural Liquefeito): controle de emergencia

Energy Technology Data Exchange (ETDEWEB)

Berardinelli, Ricardo Porto; Correa, Kleber Macedo; Moura Filho, Nelson Barboza de; Matos, Jose Eduardo Nogueira de; Fernandez, Carlos Antonio [TRANSPETRO, Rio de Janeiro, RJ (Brazil). Gerencia de Seguranca, Meio Ambiente e Saude

2008-07-01

The operation to Liquefied Natural Gas (LNG) is innovative for the PETROBRAS System. PETROBRAS Transporte - TRANSPETRO will operate two LNG flexible terminals. In accordance with the health, safety and environmental policy - training, education and awareness action plans were formulated by TRANSPETRO to assure the operational safety for the activity. Part of this action plan includes the training of LNG spill control and fire suppression. The training was carried out in 20 hours and divided into two parts: theoretical and practice. In the practice part, 3.000 gallons of LNG were unloaded and the students could verify the behaviour of the LNG and the effectiveness of the resources available for the emergency control. The knowledge was introduced in the company to create specific procedures, local emergency plans and develop internal instructors. (author)

Some links on this page may take you to non-federal websites. Their policies may differ from this site.