WorldWideScience

Sample records for lithium 6 reactions

  1. Electrodeless, multi-megawatt reactor for room-temperature, lithium-6/deuterium nuclear reactions

    International Nuclear Information System (INIS)

    Drexler, J.

    1993-01-01

    This paper describes a reactor design to facilitate a room-temperature nuclear fusion/fission reaction to generate heat without generating unwanted neutrons, gamma rays, tritium, or other radioactive products. The room-temperature fusion/fission reaction involves the sequential triggering of billions of single-molecule, 6 LiD 'fusion energy pellets' distributed in lattices of a palladium ion accumulator that also acts as a catalyst to produce the molecules of 6 LiD from a solution comprising D 2 O, 6 LiOD with D 2 gas bubbling through it. The D 2 gas is the source of the negative deuterium ions in the 6 LiD molecules. The next step is to trigger a first nuclear fusion/fission reaction of some of the 6 LiD molecules, according to the well-known nuclear reaction: 6 Li + D → 2 4 He + 22.4 MeV. The highly energetic alpha particles ( 4 He nuclei) generated by this nuclear reaction within the palladium will cause shock and vibrations in the palladium lattices, leading to compression of other 6 LiD molecules and thereby triggering a second series of similar fusion/fission reactions, leading to a third series, and so on. The absorption of the kinetic energy in the palladium will, in turn, generate a continuous flow of heat into the heavy water carrier, which would be removed with a heat exchanger. (author)

  2. Measurement of the 2H(7Be, 6Li)3He reaction rate and its contribution to the primordial lithium abundance

    Science.gov (United States)

    Li, Er-Tao; Li, Zhi-Hong; Yan, Sheng-Quan; Su, Jun; Guo, Bing; Li, Yun-Ju; Wang, You-Bao; Lian, Gang; Zeng, Sheng; Chen, Si-Zhe; Ma, Shao-Bo; Li, Xiang-Qing; He, Cao; Sun, Hui-Bin; Liu, Wei-Ping

    2018-04-01

    In the standard Big Bang nucleosynthesis (SBBN) model, the lithium puzzle has attracted intense interest over the past few decades, but still has not been solved. Conventionally, the approach is to include more reactions flowing into or out of lithium, and study the potential effects of those reactions which were not previously considered. 7Be(d, 3He)6Li is a reaction that not only produces 6Li but also destroys 7Be, which decays to 7Li, thereby affecting 7Li indirectly. Therefore, this reaction could alleviate the lithium discrepancy if its reaction rate is sufficiently high. However, there is not much information available about the 7Be(d, 3He)6Li reaction rate. In this work, the angular distributions of the 7Be(d, 3He)6Li reaction are measured at the center of mass energies E cm = 4.0 MeV and 6.7 MeV with secondary 7Be beams for the first time. The excitation function of the 7Be(d, 3He)6Li reaction is first calculated with the computer code TALYS and then normalized to the experimental data, then its reaction rate is deduced. A SBBN network calculation is performed to investigate its influence on the 6Li and 7Li abundances. The results show that the 7Be(d, 3He)6Li reaction has a minimal effect on 6Li and 7Li because of its small reaction rate. Therefore, the 7Be(d, 3He)6Li reaction is ruled out by this experiment as a means of alleviating the lithium discrepancy. Supported by National Natural Science Foundation of China (11375269, 11505117, 11490560, 11475264, 11321064), Natural Science Foundation of Guangdong Province (2015A030310012), 973 program of China (2013CB834406) and National key Research and Development Province (2016YFA0400502)

  3. Interfacial reactions in lithium batteries

    International Nuclear Information System (INIS)

    Chen, Zonghai; Amine, Khalil; Amine, Rachid; Ma, Zi-Feng

    2017-01-01

    The lithium-ion battery was first commercially introduced by Sony Corporation in 1991 using LiCoO 2 as the cathode material and mesocarbon microbeads (MCMBs) as the anode material. After continuous research and development for 25 years, lithium-ion batteries have been the dominant energy storage device for modern portable electronics, as well as for emerging applications for electric vehicles and smart grids. It is clear that the success of lithium-ion technologies is rooted to the existence of a solid electrolyte interphase (SEI) that kinetically suppresses parasitic reactions between the lithiated graphitic anodes and the carbonate-based non-aqueous electrolytes. Recently, major attention has been paid to the importance of a similar passivation/protection layer on the surface of cathode materials, aiming for a rational design of high-energy-density lithium-ion batteries with extended cycle/calendar life. In this article, the physical model of the SEI, as well as recent research efforts to understand the nature and role of the SEI are summarized, and future perspectives on this important research field will also be presented. (topical review)

  4. Interfacial reactions in lithium batteries

    Science.gov (United States)

    Chen, Zonghai; Amine, Rachid; Ma, Zi-Feng; Amine, Khalil

    2017-08-01

    The lithium-ion battery was first commercially introduced by Sony Corporation in 1991 using LiCoO2 as the cathode material and mesocarbon microbeads (MCMBs) as the anode material. After continuous research and development for 25 years, lithium-ion batteries have been the dominant energy storage device for modern portable electronics, as well as for emerging applications for electric vehicles and smart grids. It is clear that the success of lithium-ion technologies is rooted to the existence of a solid electrolyte interphase (SEI) that kinetically suppresses parasitic reactions between the lithiated graphitic anodes and the carbonate-based non-aqueous electrolytes. Recently, major attention has been paid to the importance of a similar passivation/protection layer on the surface of cathode materials, aiming for a rational design of high-energy-density lithium-ion batteries with extended cycle/calendar life. In this article, the physical model of the SEI, as well as recent research efforts to understand the nature and role of the SEI are summarized, and future perspectives on this important research field will also be presented.

  5. Examination results on reaction of lithium

    International Nuclear Information System (INIS)

    Asada, Takashi

    2000-12-01

    Before the material corrosion tests in lithium, the reactions of lithium with air and ammonia that will be used for lithium cleaning were examined, and the results were as follows. 1. When lithium put into air, surface of lithium changes to black first but soon to white, and the white layer becomes gradually thick. The first black of lithium surface is nitride (Li 3 N) and it changes to white lithium hydroxide (LiOH) by reaction with water in air, and it grows. The growth rate of the lithium hydroxide is about 1/10 in the desiccator (humidity of about 10%) compare with in air. 2. When lithium put into nitrogen, surface of lithium changes to black, and soon changes to brown and cracks at surface. At the same time with this cracking, weight of lithium piece increases and nitridation progresses respectively rapidly. This nitridation completed during 1-2 days on lithium rod of 10 mm in diameter, and increase in weight stopped. 3. Lithium melts in liquid ammonia and its melting rate is about 2-3 hour to lithium of 1 g. The liquid ammonia after lithium melting showed dark brown. (author)

  6. Temperature effects on lithium-nitrogen reaction rates

    International Nuclear Information System (INIS)

    Ijams, W.J.; Kazimi, M.S.

    1985-08-01

    A series of experiments have been run with the aim of measuring the reaction rate of lithium and nitrogen over a wide spectrum of lithium pool temperatures. In these experiments, pure nitrogen was blown at a controlled flow rate over a preheated lithium pool. The pool had a surface area of approximately 4 cm 2 and a total volume of approximately 6 cm 3 . The system pressure varied from 0 to 4 psig. The reaction rate was very small - approximately 0.002 to 0.003 g Li min cm 2 for lithium temperatures below 500 0 C. Above 500 0 C the reaction rate began to increase sharply, and reached a maximum of approximately 0.80 g Li min cm 2 above 700 0 C. It dropped off beyond 1000 0 C and seemed to approach zero at 1150 0 C. The maximum reaction rate observed in these forced convection experiments was higher by 60% than those previously observed in experiments where the nitrogen flowed to the reaction site by means of natural convection. During a reaction, a hard nitride layer built up on the surface of the lithium pool - its effect on the reaction rate was observed. The effect of the nitrogen flow rate on the reaction rate was also observed

  7. Kinetics of liquid lithium reaction with oxygen-nitrogen mixtures

    International Nuclear Information System (INIS)

    Gil, T.K.; Kazimi, M.S.

    1986-01-01

    A series of experiments have been conducted in order to characterize the kinetics of lithium chemical reaction with a mixture of oxygen and nitrogen. Three mixed gas compositions were used; 80% N 2 and 20% O 2 , 90% N 2 and 10% O 2 , and 95% N 2 and 5% O 2 . The reaction rate was obtained as a function of lithium temperature and the oxygen fraction. Liquid lithium temperature varied from 400 to 1100 0 C. By varying the composition, the degree of inhibition of the lithium-nitrogen reaction rate due to the presence of oxygen was observed. The results indicate that the lithium-nitrogen reaction rate depended on both the fraction of oxygen present and lithium temperature. The lithium nitride layer formed from the reaction also had a significant inhibition effect on the lithium-nitrogen reaction rate while the lithium-oxygen reaction rate was not as greatly hindered. LITFIRE, a computer code which simulates temperature and pressure history in a containment building following lithium spills, was modified by including (1) an improved model for the lithium-nitrogen reaction rate and (2) a model for the lithium-CO 2 reaction. LITFIRE was used to simulate HEDL's LC-2 and LA-5 experiments, and the predicted temperatures and pressures were in a reasonable agreement. Furthermore, LITFIRE was applied to a prototypical fusion reactor containment in order to simulate the consequences of a lithium spill accident. The result indicated that if nitrogen was used as containment building gas during the accident, the consequences of the accident would be less severe than those with air. The pressure rise in the building was found to be reduced by 50% and the maximum temperature of the combustion zone was limited to 900 0 C instead of 1200 0 C in the case of air

  8. Mathematical modeling of the lithium deposition overcharge reaction in lithium-ion batteries using carbon-based negative electrodes

    International Nuclear Information System (INIS)

    Arora, P.; Doyle, M.; White, R.E.

    1999-01-01

    Two major issues facing lithium-ion battery technology are safety and capacity grade during cycling. A significant amount of work has been done to improve the cycle life and to reduce the safety problems associated with these cells. This includes newer and better electrode materials, lower-temperature shutdown separators, nonflammable or self-extinguishing electrolytes, and improved cell designs. The goal of this work is to predict the conditions for the lithium deposition overcharge reaction on the negative electrode (graphite and coke) and to investigate the effect of various operating conditions, cell designs and charging protocols on the lithium deposition side reaction. The processes that lead to capacity fading affect severely the cycle life and rate behavior of lithium-ion cells. One such process is the overcharge of the negative electrode causing lithium deposition, which can lead to capacity losses including a loss of active lithium and electrolyte and represents a potential safety hazard. A mathematical model is presented to predict lithium deposition on the negative electrode under a variety of operating conditions. The Li x C 6 vertical bar 1 M LiPF 6 , 2:1 ethylene carbonate/dimethyl carbonate, poly(vinylidene fluoride-hexafluoropropylene) vert b ar LiMn 2 O 4 cell is simulated to investigate the influence of lithium deposition on the charging behavior of intercalation electrodes. The model is used to study the effect of key design parameters (particle size, electrode thickness, and mass ratio) on the lithium deposition overcharge reaction. The model predictions are compared for coke and graphite-based negative electrodes. The cycling behavior of these cells is simulated before and after overcharge to understand the hazards and capacity fade problems, inherent in these cells, can be minimized

  9. Studying reaction products in a lithium thionyl chloride cell

    International Nuclear Information System (INIS)

    Vol'fkovich, Yu.M.; Sosenkin, V.E.; Nikol'skaya, N.F.; Blinov, I.A.

    1999-01-01

    Change in the mass, volume and chemical composition of reaction insoluble products (RIP) formed in the course of discharge of thionyl chloride lithium cells under different conditions has been studied by the methods of gravimetry, volumetry and element analysis. It has been ascertained that the measured volume and mass of RIP essentially (by a factor of 1.1-1.8) exceed the calculated values, proceeding from the reaction stoichiometry. Besides lithium chloride and sulfur during discharge additional RIP is formed as LiAlCl 4 · SOCl 2 solvate, its share increasing with temperature decrease, increase in current density and electrolyte concentration [ru

  10. Mechanisms of emission of particles charged in 6Li + 6Li and 6Li + 10B reactions at low energies

    International Nuclear Information System (INIS)

    Quebert, Jean

    1964-01-01

    The lithium 6 nucleus is a projectile of interest to study nuclear reactions at low energy due to the possibility to obtain high heats of reaction, and to its structure which can play an important role in the projectile-target interaction. This research thesis focused on the study of two low-energy reactions provoked by lithium projectiles. These reactions are studied within the framework of the theoretical model of aggregates. The first part presents the experimental conditions of both reactions, reports the development and analysis of nuclear plates, and the transformation of a given type of particle histogram into a spectrum in the mass centre system. The next parts report the study of the 6 Li + 6 Li reaction (previous results, kinematic analysis, spectrum of secondary particles, theoretical analysis of results) and of the 6 Li + 10 B reaction (previous results, experimental results, study of the continuous spectrum of alpha particle, reaction mechanisms)

  11. Lithium cell reactions. Interim report, December 1981-May 1983. [Lithium-thionyl chloride cell

    Energy Technology Data Exchange (ETDEWEB)

    Clark, W.; Dampier, F.; Lombardi, A.; Cole, T.

    1983-12-01

    This report presents the results of a program that investigated reactions occurring in lithium-thionyl chloride cells for a range of specified test conditions and also performed detailed analyses for impurities present in cell components, assessed the impact of each impurity on cell performance and safety, and recommended concentration limits for detrimental impurities. Methods used in the program included linear sweep voltammetry, constant current coulometry, infrared spectroscopy, chemical analysis of the reagents and cell components, and cell discharge tests.

  12. Hydrogen production via thermochemical water-splitting by lithium redox reaction

    International Nuclear Information System (INIS)

    Nakamura, Naoya; Miyaoka, Hiroki; Ichikawa, Takayuki; Kojima, Yoshitsugu

    2013-01-01

    Highlights: •Hydrogen production via water-splitting by lithium redox reactions possibly proceeds below 800 °C. •Entropy control by using nonequilibrium technique successfully reduces the reaction temperature. •The operating temperature should be further reduced by optimizing the nonequilibrium condition to control the cycle. -- Abstracts: Hydrogen production via thermochemical water-splitting by lithium redox reactions was investigated as energy conversion technique. The reaction system consists of three reactions, which are hydrogen generation by the reaction of lithium and lithium hydroxide, metal separation by thermolysis of lithium oxide, and oxygen generation by hydrolysis of lithium peroxide. The hydrogen generation reaction completed at 500 °C. The metal separation reaction is thermodynamically difficult because it requires about 3400 °C in equilibrium condition. However, it was indicated from experimental results that the reaction temperature was drastically reduced to 800 °C by using nonequilibrium technique. The hydrolysis reaction was exothermic reaction, and completed by heating up to 300 °C. Therefore, it was expected that the water-splitting by lithium redox reactions was possibly operated below 800 °C under nonequilibrium condition

  13. Investigation of the mechanism of interaction of Lithium 6 ions on Beryllium 9

    International Nuclear Information System (INIS)

    Coste, Mireille

    1962-01-01

    The objective of this research on the interaction of Lithium 6 and Beryllium 9 ions is to obtain new indications on the mode of interaction of these heavy ions, and on the configuration of target nuclei and projectile nuclei. In a first part, the author presents and describes the experimental conditions which comprise a Van de Graaff accelerator, a source, a stripper, and a target. He reports the study of α particles emitted by the reaction between the Lithium and Beryllium ions: description of the experimental installation (irradiation chamber and method), presentation and interpretation of experimental results. In the next part, he reports the study of Lithium 7 and Beryllium 10 nuclides emitted by disintegration of Beryllium 11: description of experimental conditions, variations of cross sections, variation of the cross section rate, and interpretation. The author then addresses the study of the intervention of the mode of interaction by 15 N compound nucleus in the reactions between lithium and beryllium ions: study of intensities of the different spectrum lines, measurement of the Doppler effect produced of the 479 keV line, interpretation of results. In conclusion, the author analyses the mechanism of interaction between lithium and beryllium ions, and discusses different theories: the Newns and Glendenning theories, and the Leigh theory

  14. Metal hydrides: an innovative and challenging conversion reaction anode for lithium-ion batteries.

    Science.gov (United States)

    Aymard, Luc; Oumellal, Yassine; Bonnet, Jean-Pierre

    2015-01-01

    The state of the art of conversion reactions of metal hydrides (MH) with lithium is presented and discussed in this review with regard to the use of these hydrides as anode materials for lithium-ion batteries. A focus on the gravimetric and volumetric storage capacities for different examples from binary, ternary and complex hydrides is presented, with a comparison between thermodynamic prediction and experimental results. MgH2 constitutes one of the most attractive metal hydrides with a reversible capacity of 1480 mA·h·g(-1) at a suitable potential (0.5 V vs Li(+)/Li(0)) and the lowest electrode polarization (lithium are subsequently detailed for MgH2, TiH2, complex hydrides Mg2MH x and other Mg-based hydrides. The reversible conversion reaction mechanism of MgH2, which is lithium-controlled, can be extended to others hydrides as: MH x + xLi(+) + xe(-) in equilibrium with M + xLiH. Other reaction paths-involving solid solutions, metastable distorted phases, and phases with low hydrogen content-were recently reported for TiH2 and Mg2FeH6, Mg2CoH5 and Mg2NiH4. The importance of fundamental aspects to overcome technological difficulties is discussed with a focus on conversion reaction limitations in the case of MgH2. The influence of MgH2 particle size, mechanical grinding, hydrogen sorption cycles, grinding with carbon, reactive milling under hydrogen, and metal and catalyst addition to the MgH2/carbon composite on kinetics improvement and reversibility is presented. Drastic technological improvement in order to the enhance conversion process efficiencies is needed for practical applications. The main goals are minimizing the impact of electrode volume variation during lithium extraction and overcoming the poor electronic conductivity of LiH. To use polymer binders to improve the cycle life of the hydride-based electrode and to synthesize nanoscale composite hydride can be helpful to address these drawbacks. The development of high-capacity hydride anodes should

  15. Results and code prediction comparisons of lithium-air reaction and aerosol behavior tests

    International Nuclear Information System (INIS)

    Jeppson, D.W.

    1986-03-01

    The Hanford Engineering Development Laboratory (HEDL) Fusion Safety Support Studies include evaluation of potential safety and environmental concerns associated with the use of liquid lithium as a breeder and coolant for fusion reactors. Potential mechanisms for volatilization and transport of radioactive metallic species associated with breeder materials are of particular interest. Liquid lithium pool-air reaction and aerosol behavior tests were conducted with lithium masses up to 100 kg within the 850-m 3 containment vessel in the Containment Systems Test Facility. Lithium-air reaction rates, aerosol generation rates, aerosol behavior and characterization, as well as containment atmosphere temperature and pressure responses were determined. Pool-air reaction and aerosol behavior test results were compared with computer code calculations for reaction rates, containment atmosphere response, and aerosol behavior. The volatility of potentially radioactive metallic species from a lithium pool-air reaction was measured. The response of various aerosol detectors to the aerosol generated was determined. Liquid lithium spray tests in air and in nitrogen atmospheres were conducted with lithium temperatures of about 427 0 and 650 0 C. Lithium reaction rates, containment atmosphere response, and aerosol generation and characterization were determined for these spray tests

  16. Metal hydrides: an innovative and challenging conversion reaction anode for lithium-ion batteries

    Directory of Open Access Journals (Sweden)

    Luc Aymard

    2015-08-01

    Full Text Available The state of the art of conversion reactions of metal hydrides (MH with lithium is presented and discussed in this review with regard to the use of these hydrides as anode materials for lithium-ion batteries. A focus on the gravimetric and volumetric storage capacities for different examples from binary, ternary and complex hydrides is presented, with a comparison between thermodynamic prediction and experimental results. MgH2 constitutes one of the most attractive metal hydrides with a reversible capacity of 1480 mA·h·g−1 at a suitable potential (0.5 V vs Li+/Li0 and the lowest electrode polarization (2, TiH2, complex hydrides Mg2MHx and other Mg-based hydrides. The reversible conversion reaction mechanism of MgH2, which is lithium-controlled, can be extended to others hydrides as: MHx + xLi+ + xe− in equilibrium with M + xLiH. Other reaction paths—involving solid solutions, metastable distorted phases, and phases with low hydrogen content—were recently reported for TiH2 and Mg2FeH6, Mg2CoH5 and Mg2NiH4. The importance of fundamental aspects to overcome technological difficulties is discussed with a focus on conversion reaction limitations in the case of MgH2. The influence of MgH2 particle size, mechanical grinding, hydrogen sorption cycles, grinding with carbon, reactive milling under hydrogen, and metal and catalyst addition to the MgH2/carbon composite on kinetics improvement and reversibility is presented. Drastic technological improvement in order to the enhance conversion process efficiencies is needed for practical applications. The main goals are minimizing the impact of electrode volume variation during lithium extraction and overcoming the poor electronic conductivity of LiH. To use polymer binders to improve the cycle life of the hydride-based electrode and to synthesize nanoscale composite hydride can be helpful to address these drawbacks. The development of high-capacity hydride anodes should be inspired by the emergent

  17. Astrophysical S-factor for destructive reactions of lithium-7 in big bang nucleosynthesis

    Energy Technology Data Exchange (ETDEWEB)

    Komatsubara, Tetsuro; Kwon, YoungKwan; Moon, JunYoung; Kim, Yong-Kyun [Rare Isotope Science Project, Institute for Basic Science, Daejeon (Korea, Republic of); Moon, Chang-Bum [Hoseo University, Asan, Chungnam (Korea, Republic of); Ozawa, Akira; Sasa, Kimikazu; Onishi, Takahiro; Yuasa, Toshiaki; Okada, Shunsuke; Saito, Yuta [Division of Physics, University of Tsukuba, Tsukuba, Ibaraki (Japan); Hayakawa, Takehito; Shizuma, Toshiyuki [Japan Atomic Energy Agency, Shirakata Shirane, Tokai, Ibaraki (Japan); Kubono, Shigeru [RIKEN, Hirosawa, Wako, Saitama (Japan); Kusakabe, Motohiko [School of Liberal Arts and Science, Korea Aerospace University (Korea, Republic of); Kajino, Toshitaka [National Astronomical Observatory, Osawa, Mitaka, Tokyo (Japan)

    2014-05-02

    One of the most prominent success with the Big Bang models is the precise reproduction of mass abundance ratio for {sup 4}He. In spite of the success, abundances of lithium isotopes are still inconsistent between observations and their calculated results, which is known as lithium abundance problem. Since the calculations were based on the experimental reaction data together with theoretical estimations, more precise experimental measurements may improve the knowledge of the Big Bang nucleosynthesis. As one of the destruction process of lithium-7, we have performed measurements for the reaction cross sections of the {sup 7}L({sup 3}He,p){sup 9}Be reaction.

  18. The reaction kinetics of lithium salt with water vapor

    International Nuclear Information System (INIS)

    Balooch, M.; Dinh, L.N.; Calef, D.F.

    2002-01-01

    The interaction of lithium salt (LiH and/or LiD) with water vapor in the partial pressure range of 10 -5 -2657 Pa has been investigated. The reaction probability of water with LiH cleaved in an ultra high vacuum environment was obtained using the modulated molecular beam technique. This probability was 0.11 and independent of LiH surface temperature, suggesting a negligible activation energy for the reaction in agreement with quantum chemical calculations. The value gradually reduced, however, to 0.007 as the surface concentration of oxygen containing product approached full coverage. As the film grew beyond a monolayer, the phase lag of hydrogen product increased from 0 deg. C to 20 deg. C and the reaction probability reduced further until it approached our detection limit (∼10 -4 ). This phase lag was attributed to a diffusion-limited process in this regime. For micrometer thick hydroxide films grown in high moisture concentration environment on LiD and LiH, the reaction probability reduced to ∼4x10 -7 and was independent of exposure time. In this regime of thick hydroxide films (LiOH and/or LiOD), microcracks generated in the films to release stress provided easier pathways for moisture to reach the interface. A modified microscope, capable of both atomic force microscopy and nanoindentation, was also employed to investigate the surface morphology of hydroxide monohydrate (LiOH · H 2 O and/or LiOD · H 2 O) grown on hydroxide at high water vapor partial pressures and the kinetics of this growth

  19. The effects of lithium hydroxide solution on alkali silica reaction gels created with opal

    International Nuclear Information System (INIS)

    Mitchell, Lyndon D.; Beaudoin, James J.; Grattan-Bellew, Patrick

    2004-01-01

    The reaction of Nevada opal with calcium hydroxide, potassium hydroxide and lithium hydroxide solutions was investigated. In addition, opal was exposed to a combined solution of these three hydroxides. The progress of the three reactions was followed using X-ray diffraction (XRD), 29 Si nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM). The XRD results indicated the presence of a low-angle peak exclusive to the lithium-based reactions. The NMR results suggested a change in the silicate structure in the presence of lithium. These techniques indicated that the reaction of the alkali with the opal starting material is inhibited and perhaps stopped in the presence of lithium hydroxide. SEM revealed that the morphology of the reaction products on the surface of the reacted opal grains is markedly different invariably. It was concluded that evidence to support the theory of a protective layer exists and that the nature of the layer varies with ion type

  20. Study on lithium migration for electrochemical treatment of concrete affected by alkali-silica reaction

    NARCIS (Netherlands)

    Souza, L.M.S.; Copuroglu, O.; Polder, R.B.

    2014-01-01

    Alkali-silica reaction (ASR) is one of the major durability problems in concrete and affects many structures worldwide. Nevertheless, currently, there are no definite treatments to stop it once it has star ted. Lithium is known to have beneficial effects on ASR. Indeed, the use of lithium-based

  1. Primordial lithium: New reaction rates, new abundances, new constraints

    International Nuclear Information System (INIS)

    Kawano, L.; Schramm, D.; Steigman, G.

    1986-12-01

    Newly measured nuclear reaction rates for 3 H(α,γ) 7 Li (higher than previous values) and 7 Li(p,α) 4 He (lower than previous values) are shown to increase the 7 Li yield from big bang nucleosynthesis for lower baryon to photon ratio (eta ≤ 4 x 10 -10 ); the yield for higher eta is not affected. New, independent determinations of Li abundances in extreme Pop II stars are in excellent agreement with the earlier work of the Spites and give continued confidence in the use of 7 Li in big bang baryon density determinations. The new 7 Li constraints imply a lower limit on eta of 2 x 10 -10 and an upper limit of 5 x 10 -10 . This lower limit to eta is concordant with that obtained from considerations of D + 3 He. The upper limit is consistent with, but even more restrictive than, the D bound. With the new rates, any observed primordial Li/H ratio below 10 -10 would be inexplicable by the standard big bang nucleosynthesis. A review is made of the strengths and possible weaknesses of utilizing conclusions drawn from big bang lithium considerations. An appendix discusses the null effect of a factor of 32 increase in the experimental rate for the D(d,γ) 4 He reaction. 28 refs., 1 fig

  2. Electrochemical reaction of lithium with orthorhombic bismuth tungstate thin films fabricated by radio-frequency sputtering

    International Nuclear Information System (INIS)

    Li Chilin; Sun Ke; Yu Le; Fu Zhengwen

    2009-01-01

    Bi 2 WO 6 thin films with fast deposition rate have been fabricated by radio-frequency (R.F.) sputtering deposition, and are used as positive electrodes in rechargeable thin film lithium batteries. An initial discharge capacity of 113 μAh/cm 2 -μm is obtainable for Bi 2 WO 6 film electrode with good capacity reversibility. A multiple-center reactive mechanism associated with both Bi 3+ /Bi 0 and W 6+ /W x+ (x 2 WO 6 electrochemical performance with those of Bi 2 O 3 and WO 3 thin films. A possible explanation about smooth capacity loss of Bi 2 WO 6 after long-term cycling is suggested from the incomplete reaction of Bi component. The advantages of Bi 2 WO 6 thin films over the singer-center Bi 2 O 3 or WO 3 thin films are shown in both the aspects of volumetric capacity and cycling life.

  3. Potential design modifications for the High Yield Lithium Injection Fusion Energy (HYLIFE) reaction chamber

    International Nuclear Information System (INIS)

    Pitts, J.H.; Hovingh, J.; Meier, W.R.; Monsler, M.J.; Powell, E.G.; Walker, P.E.

    1979-01-01

    Generation of electric power from inertial confinement fusion requires a reaction chamber. One promising type, the High Yield Lithium Injection Fusion Energy (HYLIFE) chamber, includes a falling array of liquid lithium jets. These jets act as: (1) a renewable first wall and blanket to shield metal components from x-ray and neutron exposure, (2) a tritium breeder to replace tritium burned during the fusion process, and (3) an absorber and transfer medium for fusion energy. Over 90% of the energy produced in the reaction chamber is absorbed in the lithium jet fall. Design aspects are included

  4. The use of lithium compounds for inhibiting alkali-aggregate reaction effects in pavement structures

    Science.gov (United States)

    Zapała-Sławeta, J.; Owsiak, Z.

    2018-05-01

    Internal corrosion of concrete caused by the reaction of reactive aggregate with sodium and potassium hydroxides from cement is a threat to the durability of concrete pavements. Traditional methods for reducing the negative effects of the reaction include the use of unreactive aggregates, low alkali cements, mineral additives or chemical admixtures, incorporated during mixing. Lowering the relative humidity of the concrete below 80% is another measure for limiting the destructive reaction. The incorporation of lithium compounds, in particular lithium nitrate and lithium hydroxide, to the concrete mix is a method of limiting alkali-silica reaction effects. The challenge is to reduce the negative effects of aggregate reactivity in members in which the reaction has occurred because the aggregate happened to be reactive. The paper presents ways of limiting the deterioration of ASR-affected concrete in road pavements and other forms of transportation infrastructure, mainly through the use of lithium compounds, i.e. lithium nitrate. Impregnation methods that allow the penetration of lithium ions into the concrete structure were characterized, as was the effectiveness of the solutions applied.

  5. Triple-differential cross sections of the (π+/,pp) reaction on lithium isotopes

    International Nuclear Information System (INIS)

    Rieder, R.; Barnes, P.D.; Bassalleck, B.

    1985-01-01

    The (π + ,pp) reactions on 6 Li and 7 Li have been studied at T/sub π/ = 59.4 MeV with high resolution. The first triple-differential cross sections for these reactions are presented. The data are fitted to a T-matrix and compared to the π + d → pp reaction. A model in which the pion is absorbed on a 3 S 1 (pn) pair in the lithium nucleus describes many features of the data very well. An extrapolation of our data into unmeasured regions of phase space suggests that about 60% of the pion absorption cross section on 6 Li at 59.4 MeV goes into the (π + ,pp) channel. One surprising feature of the data is that the 6 Li(π + ,pp) 4 He (2 - ) transition at 22.1 MeV excitation is strongly populated, similar to what is observed in the 6 Li(d,α) 4 He reaction. This transition involves removing one nucleon from the 1p shell and one from the 1s shell. 25 refs., 15 figs., 3 tabs

  6. The chemical kinetics of the reactions of lithium with steam-air mixtures

    International Nuclear Information System (INIS)

    Barnett, D.S.; Kazimi, M.S.

    1989-04-01

    This work involved the experimental and analytical determination of the consequences of lithium fires in the presence of steam. Experiments were performed to characterize the chemical reactions of lithium with steam-nitrogen and steam-air mixtures. Models were introduced in the LITFIRE code to describe lithium fires in the presence of steam inside the containment building and plasma chamber of a hypothetical fusion reactor. The code was also equipped with the capability to determine the effects of decay heat and lithium fire on the temperature response of the reactor first wall in the event of a coolant disturbance. Forty-two kinetics experiments were performed in which a stream of steam-nitrogen or steam-air was passed over and reacted with approximately three grams of lithium heated to a predetermined temperature. The lithium reaction rates with the constituent gases were measured and characterized for a wide range of lithium temperatures and gas compositions. Experiments were performed with steam molar concentrations of 5, 15 and 30% and lithium temperatures ranging from 400 to 1100 degree C, inclusive. The LITFIRE code was modified to enable it to model the interactions of lithium with steam-air atmospheres. Results of the reaction kinetics experiments were used in the reaction model, and the heat transfer model was expanded to allow it to handle condensible atmospheres. Three groups of accidents were investigated: a spill on the containment building floor, a spill inside the reactor plasma chamber, and a spill inside the plasma chamber with steam injection to the containment building simulating a steam line break. The results were compared to dry air cases under the same conditions. 23 refs., 66 figs., 18 tabs

  7. Structural evolution and reaction mechanism of lithium nickelate (LiNiO2 during the carbonation reaction

    Directory of Open Access Journals (Sweden)

    Daniela González-Varela

    2018-03-01

    Full Text Available Lithium nickelate (LiNiO2 was synthesized using the lithium excess method, and then characterized by X-ray diffraction, scanning electron microscopy and N2 adsorption-desorption. Finally, differential thermal and thermogravimetric analyses were performed in CO2 presence, at high temperatures. Results show that LiNiO2 is able to react with CO2 through a complex structural evolution process, where lithium atoms are released to produce Li2CO3, while some nickel atoms are rearranged on different Li1-xNi1+xO2 crystalline phases. LiNiO2-CO2 reaction kinetic parameters were determined assuming a first-order reaction, where kinetic constants tended to increase as a function of temperature. However, kinetic constant values did not follow a linear trend. This atypical behavior was attributed to LiNiO2 sintering and crystalline evolution performed as a function of temperature.

  8. Association between lithium serum level, mood state, and patient-reported adverse drug reactions during long-term lithium treatment : a naturalistic follow-up study

    NARCIS (Netherlands)

    Wilting, Ingeborg; Heerdink, Eibert R.; Mersch, Peter-Paul A.; den Boer, Johannes A.; Egberts, Antoine C. G.; Nolen, Willem A.

    To assess the association between mood state and the prevalence and the severity of lithium adverse drug reactions (ADRs). A 26-year follow-up study was conducted among patients >= 18 years treated at the outpatient lithium clinic of the University Medical Center Groningen, The Netherlands, between

  9. Lithium

    Science.gov (United States)

    Bradley, Dwight C.; Stillings, Lisa L.; Jaskula, Brian W.; Munk, LeeAnn; McCauley, Andrew D.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

    2017-12-19

    Lithium, the lightest of all metals, is used in air treatment, batteries, ceramics, glass, metallurgy, pharmaceuticals, and polymers. Rechargeable lithium-ion batteries are particularly important in efforts to reduce global warming because they make it possible to power cars and trucks from renewable sources of energy (for example, hydroelectric, solar, or wind) instead of by burning fossil fuels. Today, lithium is extracted from brines that are pumped from beneath arid sedimentary basins and extracted from granitic pegmatite ores. The leading producer of lithium from brine is Chile, and the leading producer of lithium from pegmatites is Australia. Other potential sources of lithium include clays, geothermal brines, oilfield brines, and zeolites. Worldwide resources of lithium are estimated to be more than 39 million metric tons, which is enough to meet projected demand to the year 2100. The United States is not a major producer at present but has significant lithium resources.

  10. Study of kinetics of reaction of lithium deuteride powder with O2, CO2 and water vapor

    International Nuclear Information System (INIS)

    Li Gan; Lu Guangda; Jing Wenyong; Qin Cheng

    2004-01-01

    The kinetics of reaction of lithium deuteride powder with O 2 , CO 2 and water vapor is studied. The experimental results show that lithium deuteride reacts with O 2 and CO 2 at very small reaction rate but with water vapor at comparatively larger rate at room temperature (≅28 degree C). The reaction process with water vapor could be described using the unreacted shrinking core model. The second-order kinetics is appropriate for the chemical reaction on the surface of lithium deuteride and reaction rate constant is 0.281 kPa -1 ·min -1

  11. Interaction of steel elements with products of lithium-water reactions

    International Nuclear Information System (INIS)

    Starkov, O.V.; Orlov, A.V.; Orlova, E.A.

    1980-01-01

    Isobar and isothermal potentials of reactions of products of lithium interaction with water (Li 2 O, LiOH) with components of structural steels (Fe, Cr, Ni, Cr 4 C, Ni, Ti, Si, Al) are calculated at the general pressure of P=1 at in the absence of mutual solubility of components. The chemical resistance of steel components to lithium oxide and hydroxide effect in the temperature range of 300-1500 K is estimated comparatively. Lithium oxide and hydroxide have different corrosion properties relatively to chromium-nickel steels (simple and complex compounds form with LiOH, which do not form with Li 2 O). Titanium, niobium, silicon, aluminium form stable compounds when interacting with LiOH. In reactions with Li 2 O only complex titanium compounds are stable at the temperature >1150 K; aluminium compounds are stable in the whole range of temperatures investigated

  12. Aggregation and Cooperative Effects in the Aldol Reactions of Lithium Enolates

    NARCIS (Netherlands)

    Larrañaga, O.; de Cózar, A.; Bickelhaupt, F.M.; Zangi, R.; Cossío, F.P.

    2013-01-01

    Density functional theory and Car-Parrinello molecular dynamics simulations have been carried out for model aldol reactions involving aggregates of lithium enolates derived from acetaldehyde and acetone. Formaldehyde and acetone have been used as electrophiles. It is found that the geometries of the

  13. Free energy for protonation reaction in lithium-ion battery cathode materials

    International Nuclear Information System (INIS)

    Benedek, R.; Thackeray, M. M.; van de Walle, A.

    2008-01-01

    Calculations are performed of free energies for proton-for-lithium-ion exchange reactions in lithium-ion battery cathode materials. First-principles calculations are employed for the solid phases and tabulated ionization potential and hydration energy data for aqueous ions. Layered structures, spinel LiMn 2 O 4 , and olivine LiFePO 4 are considered. Protonation is most favorable energetically in layered systems, such as Li 2 MnO 3 and LiCoO 2 . Less favorable are ion-exchange in spinel LiMn 2 O 4 and LiV 3 O 8 . Unfavorable is the substitution of protons for Li in olivine LiFePO 4 , because of the large distortion of the Fe and P coordination polyhedra. The reaction free energy scales roughly linearly with the volume change in the reaction

  14. Structure and reactivity of lithium amides. /sup 6/Li, /sup 13/C, and /sup 15/N NMR spectroscopic studies and colligative measurements of lithium diphenylamide and lithium diphenylamide-lithium bromide complex solvated by tetrahydrofuran

    Energy Technology Data Exchange (ETDEWEB)

    DePue, J.S.; Collum, D.B.

    1988-08-03

    /sup 6/Li, /sup 13/C, and /sup 15/N NMR spectroscopic studies of lithium diphenylamide in THF/hydrocarbon solutions (THF = tetrahydrofuran) detected two different species. /sup 6/Li and /sup 15/N NMR spectroscopic studies of (/sup 6/Li, /sup 15/N)lithium diphenylamide showed the species observed at low THF concentrations to be a cyclic oligomer. Structural analogies provided strong support for a dimer while colligative measurements at 0/degrees/C indicated the dimer to be di- or trisolvated. On the basis of the observed mass action effects, the species appearing at intermediate THF concentrations is assigned as a contact or solvent-separated ion-paired monomer. Lithium diphenylamide forms a 1:1 adduct with lithium bromide at low THF concentrations. A combination of /sup 6/Li-/sup 15/N double labeling studies and colligative measurements supports a trisolvated cyclic mixed dimer structure. Although detailed spectroscopic studies at elevated THF concentrations were precluded by high fluctionality, the similarity of the /sup 13/C chemical shifts of lithium diphenylamide in the presence and absence of lithium bromide provide indirect evidence that the mixed dimer undergoes a THF concentration dependent dissociation to the monomeric amide and free lithium bromide. 24 references, 9 figures, 2 tables.

  15. The charge form factor and quadrupole moment of lithium-6 and -7

    International Nuclear Information System (INIS)

    Srinivasa Rao, K.; Susila, S.; Sridhar, R.

    1980-01-01

    The cluster model wave functions for lithium-6 and -7 are constructed from a two oscillator shell model wave function assuming the nucleons belonging to the clusters to be in the 1s- and 1p-shells, respectively. After first finding the range of values of the parameters in the wave function for which acceptable values of the r.m.s. radius are obtained, the range is considerably refined by a study of the form factors of these cluster nuclei. A deformation parameter is introduced in the wave functions, to get a non-spherical charge density. This parameter is uniquely fixed by the quadrupole moment for the nucleus. The model wave functions are considered to be the desirable ones for the study of cluster-knock-out reactions. (author)

  16. Investigations of oxygen reduction reactions in non-aqueous electrolytes and the lithium-air battery

    Science.gov (United States)

    O'Laoire, Cormac Micheal

    Unlocking the true energy capabilities of the lithium metal negative electrode in a lithium battery has until now been limited by the low capacity intercalation and conversion reactions at the positive electrodes. This is overcome by removing these electrodes and allowing lithium to react directly with oxygen in the atmosphere forming the Li-air battery. Chapter 2 discusses the intimate role of electrolyte, in particular the role of ion conducting salts on the mechanism and kinetics of oxygen reduction in non-aqueous electrolytes designed for such applications and in determining the reversibility of the electrode reactions. Such fundamental understanding of this high energy density battery is crucial to harnessing its full energy potential. The kinetics and mechanisms of O2 reduction in solutions of hexafluorophosphate salts of the general formula X+ PF6-, where, X = tetra butyl ammonium (TBA), K, Na and Li, in acetonitrile have been studied on glassy carbon electrodes using cyclic voltammetry (CV) and rotating disk electrode (RDE) techniques. Our results show that cation choice strongly influences the reduction mechanism of O2. Electrochemical data supports the view that alkali metal oxides formed via electrochemical and chemical reactions passivate the electrode surface inhibiting the kinetics and reversibility of the processes. The O2 reduction mechanisms in the presence of the different cations have been supplemented by kinetic parameters determined from detailed analyses of the CV and RDE data. The organic solvent present in the Li+-conducting electrolyte has a major role on the reversibility of each of the O2 reduction products as found from the work discussed in the next chapter. A fundamental study of the influence of solvents on the oxygen reduction reaction (ORR) in a variety of non-aqueous electrolytes was conducted in chapter 4. In this work special attention was paid to elucidate the mechanism of the oxygen electrode processes in the rechargeable Li

  17. Versatile Coating of Lithium Conductive Li2TiF6 on Over-lithiated Layered Oxide in Lithium-Ion Batteries

    International Nuclear Information System (INIS)

    Choi, Wonchang; Benayard, Anass; Park, Jin-Hwan; Park, Junho; Doo, Seok-Gwang; Mun, Junyoung

    2014-01-01

    Highlights: • Li 2 TiF 6 coating was designed to grow surface lithium conductivity and stability. • We conducted an easy and versatile Li 2 TiF 6 lithium conductive coating on cathode. • The coating was performed very simply by ambient-temperature co-precipitation. • After the coating, rate capability, cycleability and thermal stability improved. - Abstract: We demonstrate an easy and versatile approach to modify a cathode-surface with a highly lithium–ion conductive layer by coating it with Li 2 TiF 6 . The thin and homogeneous Li 2 TiF 6 coating is introduced onto an over-lithiated layered oxide (OLO, namely Li 1.17 Ni 0.17 Co 0.1 Mn 0.56 O 2 ) surface via simple co-precipitation at ambient temperature by using Li 2 CO 3 and H 2 TiF 6 aqueous solutions. The lithium–conductive fluoride coating is expected to effectively suppress the undesired electrochemical and thermal interfacial reactions involving the OLO, which is critical in improving cycle performance and thermal stability. After Li 2 TiF 6 surface modification, the coated OLO materials showed high rate capability as well as long cyclability and improved thermal stability. The crystalline structure and surface microstructure of the prepared OLOs were investigated by X-ray diffraction, transmission electron microscopy, and X-ray photoelectron spectroscopy. Ultimately, the performances of the assembled lithium ion batteries were thoroughly investigated by electrochemical methods and thermal analysis

  18. Investigation into key interfacial reactions within lithium-ion batteries

    Science.gov (United States)

    Vissers, Daniel Richard

    Given the concern of global climate change and the understanding that carbon dioxide emissions are driving this change, much effort has been invested into lowering carbon dioxide emissions. One approach to reduce carbon dioxide emissions is to curtail the carbon dioxide emissions from vehicles through the introduction of hybrid electric vehicles, plug-in hybrid electric vehicles, and electric vehicles. Today, lithium cobalt oxide materials are widely used in consumer electronic applications, yet these materials are cost prohibitive for larger scale vehicle applications. As a result, alternative materials with higher energy densities and lower costs are being investigated. One key alternative to cobalt that has received much attention is manganese. Manganese is of interest for its lower cost and favorable environmental friendliness. The use of manganese has led to numerous cathode materials such as Li 1-deltaMn2O4 (4V spinel), Li1-deltaMn 1.5Ni0.25O4 (5V spinel), Li1-(Mn 1-x-yNiyCox)O2 (layered), Li2MnO 3-Li1-delta(Mn1-x-yNiyCox)O 2 (layered-layered), and Li2MnO3-Li1-delta (Mn1-x-yNiyCox)1O2 -Li1-deltaMn2O4 (layered-layered-spinel). The work disclosed in the dissertation focuses on two topics associated with these manganese based cathodes. The first topic is the exceptional cyclic-ability of a high power, high energy density, 5V spinel cathode material (Li 1-deltaMn1.5Ni0.25O4) with a core-shell architecture, and the second is the severe capacity fade associated with manganese dissolution from cathodes at elevated operating temperatures. Both topics are of interest to the Li-ion battery industry. For instance, a 5V spinel cathode represents a viable path to increase both the power and energy density of Li-ion batteries. As its name implies, the 5V spinel operates at 5V that is higher than the conventional 4V lithium ion batteries. Since power and energy are directly proportional to the potential, moving from an operating potential of 4V to 5V represents an increase

  19. Development of liquid-lithium film jet-flow for the target of (7)Li(p,n)(7)Be reactions for BNCT.

    Science.gov (United States)

    Kobayashi, Tooru; Miura, Kuniaki; Hayashizaki, Noriyosu; Aritomi, Masanori

    2014-06-01

    A feasibility study on liquid lithium target in the form of a flowing film was performed to evaluate its potential use as a neutron generation target of (7)Li(p,n)(7)Be reaction in BNCT. The target is a windowless-type flowing film on a concave wall. Its configuration was adapted for a proton beam which is 30mm in diameter and with energy and current of up to 3MeV and 20mA, respectively. The flowing film of liquid lithium was 0.6mm in thickness, 50mm in width and 50mm in length. The shapes of the nozzle and concave back wall, which create a stable flowing film jet, were decided based on water experiments. A lithium hydrodynamic experiment was performed to observe the stability of liquid lithium flow behavior. The flowing film of liquid lithium was found to be feasible at temperatures below the liquid lithium boiling saturation of 342°C at the surface pressure of 1×10(-3)Pa. Using a proto-type liquid lithium-circulating loop for BNCT, the stability of the film flow was confirmed for velocities up to 30m/s at 220°C and 250°C in vacuum at a pressure lower than 10(-3) Pa. It is expected that for practical use, a flowing liquid lithium target of a windowless type can solve the problem of radiation damage and target cooling. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Dosimetric properties of dysprosium doped lithium borate glass irradiated by 6 MV photons

    International Nuclear Information System (INIS)

    Ab Rasid, A.; Wagiran, H.; Hashim, S.; Ibrahim, Z.; Ali, H.

    2015-01-01

    Undoped and dysprosium doped lithium borate glass system with empirical formula (70–x) B 2 O 3 –30 Li 2 O–(x) Dy 2 O 3 (x=0.1, 0.3, 0.5, 0.7, 1.0 mol%) were prepared using the melt-quenching technique. The dosimetric measurements were performed by irradiating the samples to 6 MV photon beam using linear accelerator (LINAC) over a dose range of 0.5–5.0 Gy. The glass series of dysprosium doped lithium borate glass produced the best thermoluminescence (TL) glow curve with the highest intensity peak from sample with 1.0 mol% Dy 2 O 3 concentration. Minimum detectable dose was detected at 2.24 mGy, good linearity of regression coefficient, high reproducibility and high sensitivity compared to the undoped glass are from 1.0 mol% dysprosium doped lithium borate glass. The results indicated that the series of dysprosium doped lithium glasses have a great potential to be considered as a thermoluminescence dosimetry (TLD). - Highlights: • TL response of undoped and dysprosium doped lithium borate glass subjected to 6 MV photons irradiation at low dose range. • TL linear response of dysprosium doped lithium borate glass. • The sensitivity of dysprosium doped lithium borate glass is approximately 93 times higher than undoped glass

  1. A green synthesis of a layered titanate, potassium lithium titanate; lower temperature solid-state reaction and improved materials performance

    International Nuclear Information System (INIS)

    Ogawa, Makoto; Morita, Masashi; Igarashi, Shota; Sato, Soh

    2013-01-01

    A layered titanate, potassium lithium titanate, with the size range from 0.1 to 30 µm was prepared to show the effects of the particle size on the materials performance. The potassium lithium titanate was prepared by solid-state reaction as reported previously, where the reaction temperature was varied. The reported temperature for the titanate preparation was higher than 800 °C, though 600 °C is good enough to obtain single-phase potassium lithium titanate. The lower temperature synthesis is cost effective and the product exhibit better performance as photocatalysts due to surface reactivity. - Graphical abstract: Finite particle of a layered titanate, potassium lithium titanate, was prepared by solid-state reaction at lower temperature to show modified materials performance. Display Omitted - Highlights: • Potassium lithium titanate was prepared by solid-state reaction. • Lower temperature reaction resulted in smaller sized particles of titanate. • 600 °C was good enough to obtain single phased potassium lithium titanate. • The product exhibited better performance as photocatalyst

  2. Why Do Lithium-Oxygen Batteries Fail: Parasitic Chemical Reactions and Their Synergistic Effect.

    Science.gov (United States)

    Yao, Xiahui; Dong, Qi; Cheng, Qingmei; Wang, Dunwei

    2016-09-12

    As an electrochemical energy-storage technology with the highest theoretical capacity, lithium-oxygen batteries face critical challenges in terms of poor stabilities and low charge/discharge round-trip efficiencies. It is generally recognized that these issues are connected to the parasitic chemical reactions at the anode, electrolyte, and cathode. While the detailed mechanisms of these reactions have been studied separately, the possible synergistic effects between these reactions remain poorly understood. To fill in the knowledge gap, this Minireview examines literature reports on the parasitic chemical reactions and finds the reactive oxygen species a key chemical mediator that participates in or facilitates nearly all parasitic chemical reactions. Given the ubiquitous presence of oxygen in all test cells, this finding is important. It offers new insights into how to stabilize various components of lithium-oxygen batteries for high-performance operations and how to eventually materialize the full potentials of this promising technology. © 2016 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  3. Nuclear reaction rates and primordial 6Li

    International Nuclear Information System (INIS)

    Nollett, K.M.; Schramm, D.N.; Lemoine, M.; Schramm, D.N.; Lemoine, M.; Schramm, D.N.

    1997-01-01

    We examine the possibility that big-bang nucleosynthesis (BBN) may produce nontrivial amounts of 6 Li. If a primordial component of this isotope could be observed, it would provide a new fundamental test of big-bang cosmology, as well as new constraints on the baryon density of the universe. At present, however, theoretical predictions of the primordial 6 Li abundance are extremely uncertain due to difficulties in both theoretical estimates and experimental determinations of the 2 H(α,γ) 6 Li radiative capture reaction cross section. We also argue that present observational capabilities do not yet allow the detection of primeval 6 Li in very metal-poor stars of the galactic halo. However, if the critical cross section is very high in its plausible range and the baryon density is relatively low, then improvements in 6 Li detection capabilities may allow the establishment of 6 Li as another product of BBN. It is also noted that a primordial 6 Li detection could help resolve current concerns about the extragalactic D/H determination. copyright 1997 The American Physical Society

  4. Reaction rates and electrical resistivities of the hydrogen isotopes with, and their solubilities in, liquid lithium

    International Nuclear Information System (INIS)

    Pulham, R.J.; Adams, P.F.; Hubberstey, P.; Parry, G.; Thunder, A.E.

    1976-01-01

    The rate of reaction, k, of hydrogen and of deuterium with liquid lithium have been determined up to pressures of 20kNm -2 and at temperatures between 230 and 270 0 C. The reaction is first order with an apparent activation energy of 52.8 and 55.2 kJmol -1 for hydrogen and deuterium, respectively. The deuterium isotope effect, k/sub H/k/sub D/, decreases from 2.95 at 230 to 2.83 at 270 0 C. Tritium is predicted to react even more slowly than deuterium. The freezing point of lithium is depressed by 0.082 and 0.075 0 C, respectively, by dissolved hydride and deuteride giving eutectics at 0.016 mol percent H and 0.012 mol percent D in the metal-salt phase diagrams. The depression and eutectic concentration are expected to be less for tritium. The increase in the resistivity of liquid lithium caused by dissolved hydrogen isotopes is linear and relatively large, 5 x 10 -8 Ωm (mol percent H or D) -1 . The solubility of lithium hydride and deuteride was determined from the marked change in resistivity on saturation. The liquidus of the metal-salt phase diagram rises steeply from the eutectic point to meet the two-immiscible liquid region. Tritium is expected to be less soluble than deuterium. The partial molar enthalpies of solution are 44.2 and 55.0 kJmol -1 for hydrogen and deuterium, respectively. These values are used to calculate the solvation enthalpies of the isotope anions in the metal

  5. Exothermic reactions among components of lithium-sulfur dioxide and lithium-thionyl chloride cells

    Science.gov (United States)

    Dallek, S.; James, S. D.; Kilroy, W. P.

    1981-03-01

    Differential scanning calorimetry measurements were made on various components of Li-SOCl2 cells to identify those combinations that react exothermically and might cause batteries to explode. The passivation of Li by SO2 in acetonitrile (AN) was characterized over a wide range of SO2 concentration (0.1-14M). In the absence of SO2, trace additions of water greatly lower the exothermicity of the Li-AN reaction. The Li-SOCl2-LiAlCl4 mixture is inert over a wide range of temperature well above the melting point of Li. However, adding carbon black converts this inert mixture into one which is highly and consistently reactive. The addition of copper powder enhances carbon's catalytic effect on the reactivity of the Li-SOCl2-LiAlCl4 mixture while trace additions of water have the opposite effect.

  6. Synthesis, crystal structure, and photoluminescence of a lithium isothiocyanate compound with 18-crown-6

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Shan; Fu, Bo; Zhao, Zhen; Liu, Xi [Chongqing Normal Univ. (China). Chongqing Key Lab. of Inorganic Functional Materials

    2018-04-01

    The investigation of the supramolecular interactions between the lithium isothiocyanate salt and 18-crown-6 (18C-6) in commercial tetrahydrofuran leads to the formation of a lithium compound, LiNCS(H{sub 2}O)(18C-6) (1). In the crystal structure the asymmetric unit contains two similar LiNCS(H{sub 2}O)(18C-6) molecules. Solid-state photoluminescence experiments have shown that compound 1 emits violet luminescence, and its possible emission mechanism was investigated in detail based on theoretical calculations.

  7. Reaction mechanism study of 7Li(7Li,6He) reaction at above ...

    Indian Academy of Sciences (India)

    The elastic scattering and the 6He angular distributions were measured in ... lithium nuclei at energies close to and far above the Coulomb barrier [1–6]. ... was fixed at 20◦ with respect to the beam direction for monitoring the beam quality ..... two-step sequential transfer calculations were performed in the framework of the.

  8. Hydrozirconation of lithium alkynylselenolate anions. Generation and reactions of alpha-zirconated vinyl selenide intermediates

    Science.gov (United States)

    Dabdoub; Begnini; Guerrero; Baroni

    2000-01-14

    Lithium alkynylselenolate anions react completely with 1.0 equiv of Cp(2)Zr(H)Cl in THF at room temperature to give exclusively the alpha-zirconated vinylselenolate intermediates 23-27, which by treatment with an alkyl halide afforded the alpha-zirconated vinyl alkylselenide intermediates 29-33. Reaction of 29-33 with butyltellurenyl bromide results in the formation of ketene telluro(seleno) acetals 35-39 with total control of the regio- and stereochemistry. The synthetic utility of the ketene telluro(seleno) acetals obtained here was demonstrated by reaction of 36 with butyllithium. This promotes the exclusive and stereospecific removal of the tellurium moiety and enables formation of the corresponding selenium-containing allylic alcohol of type 44, alpha-(alkylseleno)-alpha,beta-unsaturated aldehyde 45, ester 46, or carboxylic acid 47, after reaction with different types of electrophiles.

  9. The investigation on electrochemical reaction mechanism of CuF2 thin film with lithium

    International Nuclear Information System (INIS)

    Cui Yanhua; Xue Mingzhe; Zhou Yongning; Peng Shuming; Wang Xiaolin; Fu Zhengwen

    2011-01-01

    Crystalline CuF 2 thin films were prepared by pulsed laser deposition under room temperature. The physical and electrochemical properties of the as-deposited thin films have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), galvanostatic cycling and cyclic voltammetry (CV). Reversible capacity of 544 mAh g -1 was achieved in the potential range of 1.0-4.0 V. A reversible couple of redox peaks at 3.0 V and 3.7 V was firstly observed. By using ex situ XRD and TEM techniques, an insertion process followed by a fully conversion reaction to Cu and LiF was revealed in the lithium electrochemical reaction of CuF 2 thin film electrode. The reversible insertion reaction above 2.8 V could provide a capacity of about 125 mAh g -1 , which makes CuF 2 a potential cathode material for rechargeable lithium batteries.

  10. AN UPDATED 6Li(p, α)3He REACTION RATE AT ASTROPHYSICAL ENERGIES WITH THE TROJAN HORSE METHOD

    International Nuclear Information System (INIS)

    Lamia, L.; Spitaleri, C.; Sergi, M. L.; Pizzone, R. G.; Tumino, A.; La Cognata, M.; Tognelli, E.; Degl'Innocenti, S.; Prada Moroni, P. G.; Pappalardo, L.

    2013-01-01

    The lithium problem influencing primordial and stellar nucleosynthesis is one of the most interesting unsolved issues in astrophysics. 6 Li is the most fragile of lithium's stable isotopes and is largely destroyed in most stars during the pre-main-sequence (PMS) phase. For these stars, the convective envelope easily reaches, at least at its bottom, the relatively low 6 Li ignition temperature. Thus, gaining an understanding of 6 Li depletion also gives hints about the extent of convective regions. For this reason, charged-particle-induced reactions in lithium have been the subject of several studies. Low-energy extrapolations of these studies provide information about both the zero-energy astrophysical S(E) factor and the electron screening potential, U e . Thanks to recent direct measurements, new estimates of the 6 Li(p, α) 3 He bare-nucleus S(E) factor and the corresponding U e value have been obtained by applying the Trojan Horse method to the 2 H( 6 Li, α 3 He)n reaction in quasi-free kinematics. The calculated reaction rate covers the temperature window 0.01 to 2T 9 and its impact on the surface lithium depletion in PMS models with different masses and metallicities has been evaluated in detail by adopting an updated version of the FRANEC evolutionary code.

  11. Fast preparation of Na0.44MnO2 nanorods via a high NaOH concentration hydrothermal soft chemical reaction and their lithium storage properties

    International Nuclear Information System (INIS)

    Liu, Cai; Li, Jiangang; Zhao, Pengxiang; Guo, Wenli; Yang, Xiaoping

    2015-01-01

    This paper describes a high NaOH concentration hydrothermal soft chemical reaction to prepare Na 0.44 MnO 2 nanorods. In this process, Na-birnessite precursors and concentrated NaOH solution are introduced into the hydrothermal reaction. As a result, the hydrothermal time can be significantly shortened from 96 to 24 h, the hydrothermal temperature can be reduced from 205 to 180 °C and the yield of Na 0.44 MnO 2 can be increased from about 0.6 to about 2.4 g/(mL . day), respectively. Furthermore, the obtained Na 0.44 MnO 2 nanorods with one-dimensional tunnel structures exhibit favorable electrochemical lithium storage properties, which make them promising for the cathode materials of lithium-ion batteries

  12. THE 2H(alpha, gamma6LI REACTION AT LUNA AND BIG BANG NUCLEOSYNTHETIS

    Directory of Open Access Journals (Sweden)

    Carlo Gustavino

    2013-12-01

    Full Text Available The 2H(α, γ6Li reaction is the leading process for the production of 6Li in standard Big Bang Nucleosynthesis. Recent observations of lithium abundance in metal-poor halo stars suggest that there might be a 6Li plateau, similar to the well-known Spite plateau of 7Li. This calls for a re-investigation of the standard production channel for 6Li. As the 2H(α, γ6Li cross section drops steeply at low energy, it has never before been studied directly at Big Bang energies. For the first time the reaction has been studied directly at Big Bang energies at the LUNA accelerator. The preliminary data and their implications for Big Bang nucleosynthesis and the purported 6Li problem will be shown.

  13. Kinetic study of the dehydration reaction of lithium sulfate monohydrate crystals using microscopy and modeling

    Energy Technology Data Exchange (ETDEWEB)

    Lan, Shuiquan [Department of Mechanical Engineering, Eindhoven University of Technology, Den Dolech 2, 5612AZ Eindhoven (Netherlands); Zondag, Herbert [Department of Mechanical Engineering, Eindhoven University of Technology, Den Dolech 2, 5612AZ Eindhoven (Netherlands); Energy research Center of the Netherlands – ECN, P.O. Box 1, 1755ZG Petten (Netherlands); Steenhoven, Anton van [Department of Mechanical Engineering, Eindhoven University of Technology, Den Dolech 2, 5612AZ Eindhoven (Netherlands); Rindt, Camilo, E-mail: c.c.m.rindt@tue.nl [Department of Mechanical Engineering, Eindhoven University of Technology, Den Dolech 2, 5612AZ Eindhoven (Netherlands)

    2015-12-10

    Highlights: • Kinetics of Li{sub 2}SO{sub 4}·H{sub 2}O single crystals were modeled based on elementary processes. • Kinetics of nucleation and nuclei growth were studied by using optical microscopy. • A novel experiment was designed to visualize the reaction front into crystal bulk. • Fractional conversion was calculated and compared with TGA-experiments. - Abstract: Simulation of gas–solid reactions occurring in industrial processes requires a robust kinetic model to be applicable in a wide range of complicated reaction conditions. However, in literature it is often seen that even the same reaction under specific controlled conditions is interpreted with different kinetic models. In the present work, a phenomenological model based on nucleation and nuclei growth processes is presented to study the kinetics of the dehydration reaction of lithium sulfate monohydrate single crystals. The two elementary processes of the reaction, nucleation and nuclei growth, are characterized and quantified as a function of temperature by using optical microscopy experiments. The in-situ measured characteristics of the dehydration reaction provided confirmatory evidence that the rate of nucleation obeys an exponential law and the rate of nuclei growth is approximately constant. With knowledge acquired from the optical observations as inputs of the kinetic model, the fractional conversion of the dehydration reaction was calculated and compared with experimental results from thermogravimetric analysis (TGA). A satisfactory comparison was found both in isothermal and non-isothermal conditions. It is demonstrated that this knowledge-based model has a great potential to represent the gas–solid reaction kinetics in a wide range of process conditions regarding temperature, pressure and particle geometry.

  14. Electrochemical properties and lithium ion diffusion in Li4FeSbO6 studied by first principle

    Science.gov (United States)

    Jia, Mingzhen; Wang, Hongyan; Wang, Hui; Chen, Yuanzheng; Guo, Chunsheng; Gan, Liyong

    2017-10-01

    Due to the high capacity, Li-rich materials Li2MO3 (M = transition metal) have attracted considerable attention as the next generation of Li-ion batteries. Li4FeSbO6 is a new Li-rich layered oxide material with antiferromagnet honeycomb structure. In this work, the electrochemical behavior, charging process and oxygen stability of LixFeSbO6 (0 ≤ xextracted, the charge compensation is mainly contributed by the oxygen atoms through analyzing the Bader charges of each element. In addition, oxygen evolution reactions will occur in LixFeSbO6 (x ≤ 1.5), which will decay the capacities during cycling process. Finally, we calculated that the lithium ion can diffuse in a three-dimensional pathway with the activation barriers from 0.36 eV to 0.67 eV.

  15. Structural and electrochemical study of the reaction of lithium with silicon nanowires

    KAUST Repository

    Chan, Candace K.; Ruffo, Riccardo; Hong, Seung Sae; Huggins, Robert A.; Cui, Yi

    2009-01-01

    The structural transformations of silicon nanowires when cycled against lithium were evaluated using electrochemical potential spectroscopy and galvanostatic cycling. During the charge, the nanowires alloy with lithium to form an amorphous Lix

  16. In situ57Fe Moessbauer Investigation of Solid-State Redox Reactions of Lithium Insertion Electrodes for Advanced Batteries

    International Nuclear Information System (INIS)

    Sakai, Yoichi; Ariyoshi, Kingo; Ohzuku, Tsutomu

    2002-01-01

    A novel in situ electrochemical cell for 57 Fe Moessbauer measurements was developed in order to clarify the mechanisms of solid-state redox reactions in lithium insertion materials containing iron. Our in situ Moessbauer technique was successfully applied to the determination as to which transition metal ion was a redox center in the insertion electrodes, such as LiFe 0.5 Mn 1.5 O 4 , LiFeTiO 4 , or LiFe 0.25 Ni 0.75 O 2 , for the lithium-ion batteries.

  17. Dosimetric properties of dysprosium doped lithium borate glass irradiated by 6 MV photons

    Science.gov (United States)

    Ab Rasid, A.; Wagiran, H.; Hashim, S.; Ibrahim, Z.; Ali, H.

    2015-07-01

    Undoped and dysprosium doped lithium borate glass system with empirical formula (70-x) B2O3-30 Li2O-(x) Dy2O3 (x=0.1, 0.3, 0.5, 0.7, 1.0 mol%) were prepared using the melt-quenching technique. The dosimetric measurements were performed by irradiating the samples to 6 MV photon beam using linear accelerator (LINAC) over a dose range of 0.5-5.0 Gy. The glass series of dysprosium doped lithium borate glass produced the best thermoluminescence (TL) glow curve with the highest intensity peak from sample with 1.0 mol% Dy2O3 concentration. Minimum detectable dose was detected at 2.24 mGy, good linearity of regression coefficient, high reproducibility and high sensitivity compared to the undoped glass are from 1.0 mol% dysprosium doped lithium borate glass. The results indicated that the series of dysprosium doped lithium glasses have a great potential to be considered as a thermoluminescence dosimetry (TLD).

  18. EFFECTS OF THE LITHIUM – CONTAINING SORBENT ON TERMS OF BEHAVIORAL REACTIONS UNDER CHRONIC ALCOHOL INTOXICATION MODEL

    Directory of Open Access Journals (Sweden)

    A. A. Kotlyarova

    2016-01-01

    Full Text Available Lithium preparations are widely used for stabilize mood in case of bipolar affective disorder. Currently neuroprotective and neuroregenerative effects of lithium are of interest as in case of acute brain injury, also in chronic neurodegenerative diseases such as dementia, alcoholism, Alzheimer disease, etc. [1–5]. In clinical practice use of lithium preparations is limited due to difficult adjustment of drug dosage, necessity of monitoring its concentration in blood, side effects development as a result of accumulation of lithium in a body. For the purpose of improvement of pharmacologic properties lithium is combined with other agents (for example modifying sorbent thus it can produce longer-term and more harmless (less side reactions effect in the long view. Lithium immobilization on sorption basis will allow to use sorbent as detoxicant and carrying agent of drugs to body. The purpose of the work is studying the effect of the lithium – containing sorbent on terms of behavioral reactions under chronic alcohol intoxication model.Materials and methods. During the work we used nonlinear mice – males, which weight 25–30 g (180 animals. Chronic alcohol intoxication was precipitated via 40% proof spirit injections (oral supplementation in quantity of 3 g/kg during 2 weeks, additionally mice drunk 5% proof spirit from drinking bowl. Each experimental group consisted of 10 animals. Study drugs were inserted inside while ethanol injecting. Control animals were inserted 0,9% salin solution. Emotional state of animals was assessed through forced swim test, short – term memory assessment was performed through conditioned passive avoidance reflex. Effect of chronic alcohol intoxication on the parameters of conditioned reflex activity was measured every 7 days.Results. It was found that the investigated lithium-containing sorbent increases: the number of mice are trained passive avoidance reflex, remembering percent of electric shock

  19. Reaction mechanism and thermal stability study on cathode materials for rechargeable lithium ion batteries

    Science.gov (United States)

    Fang, Jin

    Olivine-type lithium iron phosphate has been a very promising cathode material since it was proposed by Padhi in 1997, low-cost, environmental friendly and stable structure ensure the commercialization of LiFePO 4. In LiFePO4, during charge and discharge process, Li ions are transferred between two phases, Li-poor LialphaFePO 4 and Li-rich Li1-betaFePO4, which implies a significant energy barrier for the new phase nucleation and interface growth, contrary to the fast reaction kinetics experimentally observed. The understanding of the lithiation and delithiation mechanism of this material has spurred a lot of research interests. Many theory models have been proposed to explain the reaction mechanism of LiFePO4, among them, the single phase model claims that the reaction goes through a metastable single phase, and the over potential required to form this single phase is about 30mV, so we studied the driving force to transport lithium ions between Lialpha FePO4 and Li1-betaFePO4 phases and compared the particle sizes effect. Experiment results shows that, the nano-sized (30nm) LiFePO4 has wider solid solution range, lower solid solution formation temperature and faster kinetics than normal LiFePO4 (150nm). Also a 20mV over potential was observed in both samples, either after relaxing the FePO4/LiFePO4 system to equilibrium or transport lithium from one side to the other side, the experiment result is corresponding to theoretical calculation; indicates the reaction might go through single-phase reaction mechanism. The energy and power density of lithium ion battery largely depend on cathode materials. Mn substituted LiFePO4 has a higher voltage than LiFePO4, which results a higher theoretical energy density. Safety issue is one of the most important criterions for batteries, since cathode materials need to maintain stable structure during hundreds of charge and discharge cycles and ranges of application conditions. We have reported that iron-rich compound o-Fe1-yMnyPO4

  20. Evaluating cis-2,6-Dimethylpiperidide (cis-DMP) as a Base Component in Lithium-Mediated Zincation Chemistry

    Science.gov (United States)

    Armstrong, David R; Garden, Jennifer A; Kennedy, Alan R; Leenhouts, Sarah M; Mulvey, Robert E; O'Keefe, Philip; O'Hara, Charles T; Steven, Alan

    2013-01-01

    Most recent advances in metallation chemistry have centred on the bulky secondary amide 2,2,6,6-tetramethylpiperidide (TMP) within mixed metal, often ate, compositions. However, the precursor amine TMP(H) is rather expensive so a cheaper substitute would be welcome. Thus this study was aimed towards developing cheaper non-TMP based mixed-metal bases and, as cis-2,6-dimethylpiperidide (cis-DMP) was chosen as the alternative amide, developing cis-DMP zincate chemistry which has received meagre attention compared to that of its methyl-rich counterpart TMP. A new lithium diethylzincate, [(TMEDA)LiZn(cis-DMP)Et2] (TMEDA=N,N,N′,N′-tetramethylethylenediamine) has been synthesised by co-complexation of Li(cis-DMP), Et2Zn and TMEDA, and characterised by NMR (including DOSY) spectroscopy and X-ray crystallography, which revealed a dinuclear contact ion pair arrangement. By using N,N-diisopropylbenzamide as a test aromatic substrate, the deprotonative reactivity of [(TMEDA)LiZn(cis-DMP)Et2] has been probed and contrasted with that of the known but previously uninvestigated di-tert-butylzincate, [(TMEDA)LiZn(cis-DMP)tBu2]. The former was found to be the superior base (for example, producing the ortho-deuteriated product in respective yields of 78 % and 48 % following D2O quenching of zincated benzamide intermediates). An 88 % yield of 2-iodo-N,N-diisopropylbenzamide was obtained on reaction of two equivalents of the diethylzincate with the benzamide followed by iodination. Comparisons are also drawn using 1,1,1,3,3,3-hexamethyldisilazide (HMDS), diisopropylamide and TMP as the amide component in the lithium amide, Et2Zn and TMEDA system. Under certain conditions, the cis-DMP base system was found to give improved results in comparison to HMDS and diisopropylamide (DA), and comparable results to a TMP system. Two novel complexes isolated from reactions of the di-tert-butylzincate and crystallographically characterised, namely the pre-metallation complex [{(iPr)2N

  1. APPARATUS FOR THE PRODUCTION OF LITHIUM METAL

    Science.gov (United States)

    Baker, P.S.; Duncan, F.R.; Greene, H.B.

    1961-08-22

    Methods and apparatus for the production of high-purity lithium from lithium halides are described. The apparatus is provided for continuously contacting a molten lithium halide with molten barium, thereby forming lithium metal and a barium halide, establishing separate layers of these reaction products and unreacted barium and lithium halide, and continuously withdrawing lithium and barium halide from the reaction zone. (AEC)

  2. Test of level density models from reactions of Li6 on Fe58 and Li7 on Fe57

    Science.gov (United States)

    Oginni, B. M.; Grimes, S. M.; Voinov, A. V.; Adekola, A. S.; Brune, C. R.; Carter, D. E.; Heinen, Z.; Jacobs, D.; Massey, T. N.; O'Donnell, J. E.; Schiller, A.

    2009-09-01

    The reactions of Li6 on Fe58 and Li7 on Fe57 have been studied at 15 MeV beam energy. These two reactions produce the same compound nucleus, Cu64. The charged particle spectra were measured at backward angles. The data obtained have been compared with Hauser-Feshbach model calculations. The level density parameters of Ni63 and Co60 have been obtained from the particle evaporation spectra. We also find contributions from the break up of the lithium projectiles to the low energy region of the α spectra.

  3. Much improved capacity and cycling performance of LiVMoO6 cathode for lithium ion batteries

    International Nuclear Information System (INIS)

    Zhou Liqun; Liang Yongguang; Hu Ling; Han Xiaoyan; Yi Zonghui; Sun Jutang; Yang Shuijin

    2008-01-01

    Spherical LiVMoO 6 nanocrystals as cathode for lithium ion batteries were synthesized using a solvothermal reaction method. Powder XRD data indicate that a single phase LiVMoO 6 with brannerite-type structure is obtained at 550 deg. C by the thermal treatment of the precursor for 6 h. SEM image shows that the particles are composed of loosely stacked spheres with a uniform particle size about 40 nm. The electrode properties of LiVMoO 6 have also been studied by galvanostatic cycling and ac impedance spectroscopy. LiVMoO 6 nanospheres delivered 172 mAh g -1 capacity in the initial discharge process with a reversible capacity retention of 94.4% after 100 cycles in the range of 3.6-1.80 V versus metallic Li at a current density of 100 mA g -1 . The microstructure developed in the electrodes give evidence that the particle size and morphological properties play an important role in the much improved capacity and cycling stability at large currents than ordinary samples

  4. On the possibility of using lithium-6 deuteride, irradiated with gas discharge plasma in a target with polarized nuclei of deuterium and lithium

    International Nuclear Information System (INIS)

    Bunyatova, E.I.; Bubnov, N.N.; Solodovnikov, S.P.

    1991-01-01

    A target with polarized nuclei made on the basis of irradiated lithium-6 deuteride is of great interest for carrying out investigations in elementary particle physics. Up to now high-energy electrons have been used for generation of F-centers in 6 LiD. It is shown that one can, in principle, use ultraviolet irradiation and gas discharge plasma for generation of F-centers in 6 LiD. Both types of irradiation cause electron paramagnetic resonance signals from conductance electrons of lithium and form F-centers in 6 LiD. It seems possible to obtain the necessary samples by exposing 6 LiD to the gas discharge plasma. 9 refs.; 2 figs

  5. AN UPDATED {sup 6}Li(p, {alpha}){sup 3}He REACTION RATE AT ASTROPHYSICAL ENERGIES WITH THE TROJAN HORSE METHOD

    Energy Technology Data Exchange (ETDEWEB)

    Lamia, L.; Spitaleri, C.; Sergi, M. L. [Dipartimento di Fisica e Astronomia, Universita di Catania, I-95123 Catania (Italy); Pizzone, R. G.; Tumino, A.; La Cognata, M. [INFN-Laboratori Nazionali del Sud, I-95125 Catania (Italy); Tognelli, E.; Degl' Innocenti, S.; Prada Moroni, P. G. [Dipartimento di Fisica, Universita di Pisa, I-56127 Pisa (Italy); Pappalardo, L. [Dipartimento di Fisica e Scienze della Terra, Universita di Ferrara, I-44100 Ferrara (Italy)

    2013-05-01

    The lithium problem influencing primordial and stellar nucleosynthesis is one of the most interesting unsolved issues in astrophysics. {sup 6}Li is the most fragile of lithium's stable isotopes and is largely destroyed in most stars during the pre-main-sequence (PMS) phase. For these stars, the convective envelope easily reaches, at least at its bottom, the relatively low {sup 6}Li ignition temperature. Thus, gaining an understanding of {sup 6}Li depletion also gives hints about the extent of convective regions. For this reason, charged-particle-induced reactions in lithium have been the subject of several studies. Low-energy extrapolations of these studies provide information about both the zero-energy astrophysical S(E) factor and the electron screening potential, U{sub e} . Thanks to recent direct measurements, new estimates of the {sup 6}Li(p, {alpha}){sup 3}He bare-nucleus S(E) factor and the corresponding U{sub e} value have been obtained by applying the Trojan Horse method to the {sup 2}H({sup 6}Li, {alpha} {sup 3}He)n reaction in quasi-free kinematics. The calculated reaction rate covers the temperature window 0.01 to 2T{sub 9} and its impact on the surface lithium depletion in PMS models with different masses and metallicities has been evaluated in detail by adopting an updated version of the FRANEC evolutionary code.

  6. Acetylene Black Induced Heterogeneous Growth of Macroporous CoV2O6 Nanosheet for High-Rate Pseudocapacitive Lithium-Ion Battery Anode.

    Science.gov (United States)

    Zhang, Lei; Zhao, Kangning; Luo, Yanzhu; Dong, Yifan; Xu, Wangwang; Yan, Mengyu; Ren, Wenhao; Zhou, Liang; Qu, Longbing; Mai, Liqiang

    2016-03-23

    Metal vanadates suffer from fast capacity fading in lithium-ion batteries especially at a high rate. Pseudocapacitance, which is associated with surface or near-surface redox reactions, can provide fast charge/discharge capacity free from diffusion-controlled intercalation processes and is able to address the above issue. In this work, we report the synthesis of macroporous CoV2O6 nanosheets through a facile one-pot method via acetylene black induced heterogeneous growth. When applied as lithium-ion battery anode, the macroporous CoV2O6 nanosheets show typical features of pseudocapacitive behavior: (1) currents that are mostly linearly dependent on sweep rate and (2) redox peaks whose potentials do not shift significantly with sweep rate. The macroporous CoV2O6 nanosheets display a high reversible capacity of 702 mAh g(-1) at 200 mA g(-1), excellent cyclability with a capacity retention of 89% (against the second cycle) after 500 cycles at 500 mA g(-1), and high rate capability of 453 mAh g(-1) at 5000 mA g(-1). We believe that the introduction of pseudocapacitive properties in lithium battery is a promising direction for developing electrode materials with high-rate capability.

  7. Lithium iron phosphate with high-rate capability synthesized through hydrothermal reaction in glucose solution

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Guangchuan; Wang, Li; Ou, Xiuqin; Zhao, Xia; Xu, Shengzhao [Institute of Power Source and Ecomaterials Science, Box 1055, Hebei University of Technology, 300130 Tianjin (China)

    2008-10-01

    Carbon-coated lithium iron phosphate (LiFePO{sub 4}/C) was hydrothermally synthesized from commercial LiOH, FeSO{sub 4} and H{sub 3}PO{sub 4} as raw materials and glucose as carbon precursor in aqueous solution at 180 C for 6 h followed by being fired at 750 C for 6 h. The samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and constant current charge-discharge cycling test. The results show that the synthesized powders are in situ coated with carbon precursor produced from glucose. At ambient temperature (25{+-}2 C), the specific discharge capacities are 154 mAh g{sup -1} at 0.2C and 136 mAh g{sup -1} at 5 C rate, and the cycling capacity retention rate reaches 98% over 90 cycles. The excellent electrochemical performance can be correlated with the in situ formation of carbon precursor/carbon, thus leading to the even distribution of carbon and the enhancement of conductibility of individual grains. (author)

  8. Study of cerium diffusion in undoped lithium-6 enriched glass with Rutherford backscattering spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xiaodong, E-mail: xzhang39@utk.edu [Department of Nuclear Engineering, University of Tennessee, TN 37996 (United States); Moore, Michael E.; Lee, Kyung-Min; Lukosi, Eric D. [Department of Nuclear Engineering, University of Tennessee, TN 37996 (United States); Hayward, Jason P. [Department of Nuclear Engineering, University of Tennessee, TN 37996 (United States); Oak Ridge National Lab, Oak Ridge, TN 37831 (United States)

    2016-07-01

    Undoped lithium-6 enriched glasses coated with pure cerium (99.9%) with a gold protection layer on top were heated at three different temperatures (500, 550, and 600 °C) for varied durations (1, 2, and 4 h). Diffusion profiles of cerium in such glasses were obtained with the conventional Rutherford backscattering technique. Through fitting the diffusion profiles with the thin-film solution of Fick’s second law, diffusion coefficients of cerium with different annealing temperatures and durations were solved. Then, the activation energy of cerium for the diffusion process in the studied glasses was found to be 114 kJ/mol with the Arrhenius equation.

  9. Study of cerium diffusion in undoped lithium-6 enriched glass with Rutherford backscattering spectrometry

    Science.gov (United States)

    Zhang, Xiaodong; Moore, Michael E.; Lee, Kyung-Min; Lukosi, Eric D.; Hayward, Jason P.

    2016-07-01

    Undoped lithium-6 enriched glasses coated with pure cerium (99.9%) with a gold protection layer on top were heated at three different temperatures (500, 550, and 600 °C) for varied durations (1, 2, and 4 h). Diffusion profiles of cerium in such glasses were obtained with the conventional Rutherford backscattering technique. Through fitting the diffusion profiles with the thin-film solution of Fick's second law, diffusion coefficients of cerium with different annealing temperatures and durations were solved. Then, the activation energy of cerium for the diffusion process in the studied glasses was found to be 114 kJ/mol with the Arrhenius equation.

  10. Origin of stabilization and destabilization in solid-state redox reaction of oxide ions for lithium-ion batteries.

    Science.gov (United States)

    Yabuuchi, Naoaki; Nakayama, Masanobu; Takeuchi, Mitsue; Komaba, Shinichi; Hashimoto, Yu; Mukai, Takahiro; Shiiba, Hiromasa; Sato, Kei; Kobayashi, Yuki; Nakao, Aiko; Yonemura, Masao; Yamanaka, Keisuke; Mitsuhara, Kei; Ohta, Toshiaki

    2016-12-23

    Further increase in energy density of lithium batteries is needed for zero emission vehicles. However, energy density is restricted by unavoidable theoretical limits for positive electrodes used in commercial applications. One possibility towards energy densities exceeding these limits is to utilize anion (oxide ion) redox, instead of classical transition metal redox. Nevertheless, origin of activation of the oxide ion and its stabilization mechanism are not fully understood. Here we demonstrate that the suppression of formation of superoxide-like species on lithium extraction results in reversible redox for oxide ions, which is stabilized by the presence of relatively less covalent character of Mn 4+ with oxide ions without the sacrifice of electronic conductivity. On the basis of these findings, we report an electrode material, whose metallic constituents consist only of 3d transition metal elements. The material delivers a reversible capacity of 300 mAh g -1 based on solid-state redox reaction of oxide ions.

  11. Origin of stabilization and destabilization in solid-state redox reaction of oxide ions for lithium-ion batteries

    Science.gov (United States)

    Yabuuchi, Naoaki; Nakayama, Masanobu; Takeuchi, Mitsue; Komaba, Shinichi; Hashimoto, Yu; Mukai, Takahiro; Shiiba, Hiromasa; Sato, Kei; Kobayashi, Yuki; Nakao, Aiko; Yonemura, Masao; Yamanaka, Keisuke; Mitsuhara, Kei; Ohta, Toshiaki

    2016-01-01

    Further increase in energy density of lithium batteries is needed for zero emission vehicles. However, energy density is restricted by unavoidable theoretical limits for positive electrodes used in commercial applications. One possibility towards energy densities exceeding these limits is to utilize anion (oxide ion) redox, instead of classical transition metal redox. Nevertheless, origin of activation of the oxide ion and its stabilization mechanism are not fully understood. Here we demonstrate that the suppression of formation of superoxide-like species on lithium extraction results in reversible redox for oxide ions, which is stabilized by the presence of relatively less covalent character of Mn4+ with oxide ions without the sacrifice of electronic conductivity. On the basis of these findings, we report an electrode material, whose metallic constituents consist only of 3d transition metal elements. The material delivers a reversible capacity of 300 mAh g−1 based on solid-state redox reaction of oxide ions. PMID:28008955

  12. Spectroscopic and Electrochemical Properties of Lithium-Rich LiFePO4 Cathode Synthesized by Solid-State Reaction

    Science.gov (United States)

    Rosaiah, P.; Hussain, O. M.; Zhu, Jinghui; Qiu, Yejun

    2017-08-01

    Lithium iron phosphate (Li x FePO4) is synthesized by a solid-state reaction method. The structural, electrical and electrochemical properties are studied in detail. It is found that the increment of lithium concentration (up to x = 1.05) does not affect the structure of LiFePO4 but improves its electrical conductivity as well as electrochemical performance. Surface morphological studies exhibited the formation of rod-like nanoparticles with small size. Electric and dielectric properties are also investigated over a frequency range of 1 Hz-1 MHz at different temperatures. The conductivity increased with increasing temperature, which follows the Arrhenius relation with the activation energy of about 0.31 eV. And the electrochemical tests found that the Li1.05FePO4 cathode possessed improved discharge capacity with better cycling performance.

  13. Development of In Situ Infrared Spectroelectrochemical Techniques: Application to Lithium Intercalation Reactions in Electrode Materials

    National Research Council Canada - National Science Library

    Frech, Roger

    2007-01-01

    .... The transition between LiFePO4 and FePO4 could easily be followed in the in situ spectra. An industrially available coin cell was modified to facilitate routine in situ Raman measurements of lithium batteries...

  14. X particle effect for 6Li reaction rates calculations

    International Nuclear Information System (INIS)

    Kocak, G.; Balantekin, A. B.

    2009-01-01

    The inferred primordial 6 L i-7 L i abundances are different from standard big bang nucleosynthesis results, 6 L i is 1000 times larger and 7 L i is 3 times smaller than the big bang prediction. In big bang nucleosynthesis, negatively charged massive X particles a possible solution to explain this primordial Li abundances problem [1]. In this study, we consider only X particle effect for nuclear reactions to obtain S-factor and reaction rates for Li. All S-factors calculated within the Optical Model framework for d(α,γ)6 L i system. We showed that the enhancement effect of massive negatively charged X particle for 6 L i system reaction rate.(author)

  15. Stereoselective reactions. XXXII. Enantioselective deprotonation of 4-tert-butylcyclohexanone by fluorine-containing chiral lithium amides derived from 1-phenylethylamine and 1-(1-naphthyl)ethylamine.

    Science.gov (United States)

    Aoki, K; Koga, K

    2000-04-01

    Enantioselective deprotonation of 4-tert-butylcyclohexanone was examined using 1-phenylethylamine- and 1-(1-naphthyl)ethylamine-derived chiral lithium amides having an alkyl or a fluoroalkyl substituent at the amide nitrogen. The lithium amides having a 2,2,2-trifluoroethyl group on the amide nitrogen are easily accessible in both enantiomeric forms, and were found to induce good enantioselectivity in the present reaction.

  16. Core-shell Si/Cu nanocomposites synthesized by self-limiting surface reaction as anodes for lithium ion batteries

    Science.gov (United States)

    Xu, Kaiqi; Zhang, Zhizhen; Su, Wei; Huang, Xuejie

    Core-shell Si/Cu nanocomposites were synthesized via a flexible self-limiting surface reaction without extra reductant for the first time. The nano Si was uniformly coated with Cu nanoparticles with a diameter of 5-10nm, which can enhance the electronic conductivity of the nanocomposites and buffer the huge volume change during charge/discharge owing to its high ductility. Benefited from the unique structure, the Si/Cu nanocomposites exhibited a good electrochemical performance as anodes for lithium ion batteries, which exhibited a capacity retention of 656mAh/g after 50 cycles and a coulombic efficiency of more than 99%.

  17. /sup 6/Li (e, e'X) reaction

    Energy Technology Data Exchange (ETDEWEB)

    Taneichi, H; Ueno, H [Yamagata Univ. (Japan); Shoda, K

    1974-12-01

    The target is a 99.3% enriched /sup 6/Li plate with thickness of 1.82 mg/cm/sup 2/. The energy of the electron beam ranged from 15 MeV to 31.7 MeV. Reaction products were measured by BDM which was set at the position of thetasub( l)=90/sup 0/. The (..gamma.., p) reaction was performed, the cross section was obtained. From the area ratio of P/sub 0/ and P/sub 1/ in a difference spectrum, sigma sub(p/sub 1/)/sigma sub(p/sub 0/)--3 was obtained. The cross section of the (..gamma.., t) reaction was acquired by a deduction method from two reaction spectra at Esub(e)=25 and 30 MeV. From the cross section, a reduced width theta/sup 2/--0.6 was obtained. The (..gamma.., d) reaction was measured at Esub(e)=15 MeV, and the cross section was obtained in the range from Esub(x)=8 MeV to 19 MeV by introducing previous data. The magnitude of the cross section was 0.2 to 0.1 ..mu..b/sr. The deuteron measured in this reaction must be identified whether it comes from T-impurity or E2. For the identification of this deuteron, an angular distribution measurement is needed.

  18. Study of reactions induced by 6He on 9Be

    Directory of Open Access Journals (Sweden)

    Pires K.C.C.

    2014-03-01

    Full Text Available We present the results of experiments using a 6He beam on a 9Be target at energies 7 − 9 times the Coulomb barrier. Angular distributions of the elastic, inelastic scattering (target breakup and the a-particle production in the 6He+9Be collision have been analysed. Total reaction cross sections were obtained from the elastic scatteringanalyses and a considerable enhancement has been observed by comparing to stable systems.

  19. The interstellar lithium abundance and the 7Li/6Li ratio

    International Nuclear Information System (INIS)

    Ferlet, R.; Dennefeld, M.

    1985-01-01

    The λ 6708 doublet of interstellar Li I has been observed at high spectral resolution (3.km s -1 ) and very good signal to noise ratio (∼ 4000) towards δ Sco and ζ Oph. Using a profile fitting method, we derive for the first time outside the solar system a 7 Li/ 6 Li ratio of 38 for a diffuse cloud in front of ζ Oph. Even the lower limit of the error bar is incompatible with the ratio measured in meteorites and is not explained by recent models of galactic evolution. The existence of a local inhomogeneity is suggested. Finally, as for other alkalis, lithium is depleted on to dust grains in the diffuse interstellar medium [fr

  20. Interface-modulated approach toward multilevel metal oxide nanotubes for lithium-ion batteries and oxygen reduction reaction

    Institute of Scientific and Technical Information of China (English)

    Jiashen Meng; Chaojiang Niu; Xiong Liu; Ziang Liu; Hongliang Chen; Xuanpeng Wang; Jiantao Li

    2016-01-01

    Metal oxide hollow structures with multilevel interiors are of great interest for potential applications such as catalysis,chemical sensing,drug delivery,and energy storage.However,the controlled synthesis of multilevel nanotubes remains a great challenge.Here we develop a facile interface-modulated approach toward the synthesis of complex metal oxide multilevel nanotubes with tunable interior structures through electrospinning followed by controlled heat treatment.This versatile strategy can be effectively applied to fabricate wire-in-tube and tubein-tube nanotubes of various metal oxides.These multilevel nanotubes possess a large specific surface area,fast mass transport,good strain accommodation,and high packing density,which are advantageous for lithium-ion batteries (LIBs)and the oxygen reduction reaction (ORR).Specifically,shrinkable CoMn2O4 tube-in-tube nanotubes as a lithium-ion battery anode deliver a high discharge capacity of ~565 mAh.g-1 at a high rate of 2 A.g-1,maintaining 89% of the latter after 500 cycles.Further,as an oxygen reduction reaction catalyst,these nanotubes also exhibit excellent stability with about 92% current retention after 30,000 s,which is higher than that of commercial Pt/C (81%).Therefore,this feasible method may push the rapid development of one-dimensional (1D) nanomaterials.These multifunctional nanotubes have great potential in many frontier fields.

  1. Critical appraisal on the role of catalysts for the oxygen reduction reaction in lithium-oxygen batteries

    International Nuclear Information System (INIS)

    Lodge, Andrew W.; Lacey, Matthew J.; Fitt, Matthew; Garcia-Araez, Nuria; Owen, John R.

    2014-01-01

    This work reports a detailed characterization of the reduction of oxygen in pyrrolidinium-based ionic liquids for application to lithium-oxygen batteries. It is found that, in the absence of Li + , all electron transfer kinetics are fast, and therefore, the reactions are limited by the mass transport rate. Reversible reduction of O 2 to O 2 • − and O 2 • − to O 2 2− take place at E 0 = 2.1 V and 0.8 V vs. Li + /Li, respectively. In the presence of Li + , O 2 is reduced to LiO 2 first and then to Li 2 O 2 . The solubility product constant of Li 2 O 2 is found to be around 10 −51 , corroborating the hypothesis that electrode passivation by Li 2 O 2 deposition is an important issue that limits the capacity delivered by lithium-oxygen batteries. Enhancing the rate of Li 2 O 2 formation by using different electrode materials would probably lead to faster electrode passivation and hence smaller charge due to oxygen reduction (smaller capacity of the battery). On the contrary, soluble redox catalysts can not only increase the reaction rate of Li 2 O 2 formation but also avoid electrode passivation since the fast diffusion of the soluble redox catalyst would displace the formation of Li 2 O 2 at a sufficient distance from the electrode surface

  2. Dynamic structural change of the self-assembled lanthanum complex induced by lithium triflate for direct catalytic asymmetric aldol-Tishchenko reaction.

    Science.gov (United States)

    Horiuchi, Yoshihiro; Gnanadesikan, Vijay; Ohshima, Takashi; Masu, Hyuma; Katagiri, Kosuke; Sei, Yoshihisa; Yamaguchi, Kentaro; Shibasaki, Masakatsu

    2005-09-05

    The development of a direct catalytic asymmetric aldol-Tishchenko reaction and the nature of its catalyst are described. An aldol-Tishchenko reaction of various propiophenone derivatives with aromatic aldehydes was promoted by [LaLi3(binol)3] (LLB), and reactivity and enantioselectivity were dramatically enhanced by the addition of lithium trifluoromethanesulfonate (LiOTf). First, we observed a dynamic structural change of LLB by the addition of LiOTf using 13C NMR spectroscopy, electronspray ionization mass spectrometry (ESI-MS), and cold-spray ionization mass spectrometry (CSI-MS). X-ray crystallography revealed that the structure of the newly generated self-assembled complex was a binuclear [La2Li4(binaphthoxide)5] complex 6. A reverse structural change of complex 6 to LLB by the addition of one equivalent of Li2(binol) was also confirmed by ESI-MS and experimental results. The drastic concentration effects on the direct catalytic asymmetric aldol-Tishchenko reaction suggested that the addition of LiOTf to LLB generated an active oligomeric catalyst species.

  3. Lithium uptake and the corrosion of zirconium alloys in aqueous lithium hydroxide solutions

    International Nuclear Information System (INIS)

    Ramasubramanian, N.

    1991-01-01

    This paper reports on corrosion films on zirconium alloys that were analyzed for lithium by Atomic Absorption Spectroscopy (AAS), Secondary Ion Mass Spectrometry (SIMS), and Infrared Reflection Absorption Spectroscopy (IRAS). The oxides grown in reactor in dilute lithium hydroxide solution, specimens cut from Zircaloy, and Zr-2.5Nb alloy pressure tubes removed from CANDU (Canada Deuterium Uranium, Registered Trademark) reactors showed low concentrations of lithium (4 to 50 ppm). The lithium was not leachable in a warm dilute acid. 6 Li undergoes transmutation by the 6 Li(n,t) 4 He reaction. However, SIMS profiles for d 7 Li were identical through the bulk oxide and the isotopic ratio was close to the natural abundance value. The lithium in the oxide, existing as adsorbed lithium on the surface, has been in dynamic equilibrium with lithium in the coolant, and, in spite of many Effective Full Power Years (EFPY) of operation, lithium added to the CANDU coolant at ∼2.5 ppm is not concentrating in the oxides. On the other hand, corrosion films grown in the laboratory in concentrated lithium hydroxide solutions were very porous and contained hundreds of ppm of lithium in the oxide

  4. Studying reactions of interaction of tungsten (6) with rhodamine B and rhodamine 6 Zh

    International Nuclear Information System (INIS)

    Andreeva, I.Yu.; Lebedeva, L.I.; Burmistrova, N.M.

    1978-01-01

    The reaction of the interaction between tungsten (6) and rhodamine B and rhodamine 6 Zh has been investigated. The formation of two compounds in the tungsten-rhodamine system is shown. The composition of these compounds has been determined, and their stability has been estimated. The composition of compounds in the solid phase has also been determined. This reaction is used for the determination of tungsten in stells

  5. Bis[2,6-bis(trimethylsilylaminopyridine-κN1]{[6-bis(trimethylsilylaminopyridin-2-yl-κN1](trimethylsilylazanido-κN}lithium

    Directory of Open Access Journals (Sweden)

    Justin A. Rave

    2016-03-01

    Full Text Available The title complex, [Li(C11H22N3Si2(C11H23N3Si22], contains a single lithium cation coordinated to three ligands. This is the first reported example of the ligand 2,6-bis(trimethylsilylaminopyridine supporting a monometallic complex. One ligand is mono-anionic and forms a four-membered chelate ring with the lithium cation via the pyridine and silylamido N atoms. The other two ligands are neutral and bind via the pyridine nitrogen. The lithium cation is coordinated in a tetrahedral environment. No intra- or intermolecular hydrogen bonding is observed in the crystal structure, likely indicating that weak electrostatic interactions are the dominant feature of the crystal packing.

  6. Structural and electrochemical study of the reaction of lithium with silicon nanowires

    KAUST Repository

    Chan, Candace K.

    2009-04-01

    The structural transformations of silicon nanowires when cycled against lithium were evaluated using electrochemical potential spectroscopy and galvanostatic cycling. During the charge, the nanowires alloy with lithium to form an amorphous LixSi compound. At potentials <50 mV, a structural transformation occurs. In studies on micron-sized particles previously reported in the literature, this transformation is a crystallization to a metastable Li15Si4 phase. X-ray diffraction measurements on the Si nanowires, however, show that they are amorphous, suggesting that a different amorphous phase (LiySi) is formed. Lithium is removed from this phase in the discharge to form amorphous silicon. We have found that limiting the voltage in the charge to 70 mV results in improved efficiency and cyclability compared to charging to 10 mV. This improvement is due to the suppression of the transformation at low potentials, which alloys for reversible cycling of amorphous silicon nanowires. © 2008 Elsevier B.V. All rights reserved.

  7. NaLaTi_2O_6 nanosheet as a potential anode material for lithium ion batteries

    International Nuclear Information System (INIS)

    Geng, Qiao; Cao, Liyun; Kong, Xingang; Xu, Zhanwei; Huang, Jianfeng; Li, Jiayin; Cheng, Yayi

    2016-01-01

    Highlights: • NaLaTi_2O_6 nanosheet was achieved by a simple one-step hydrothermal method. • NaLaTi_2O_6 was reported for the first time as an anode material. • NaLaTi_2O_6 shown a high discharge capacity of about 180 mAh/g at 100 mA/g. - Abstract: NaLaTi_2O_6 nanosheet was achieved by one-step hydrothermal method and was reported for the first time as an anode material for lithium ion batteries. The phase structure and morphology analysis reveals that pure pervoskite NaLaTi_2O_6 possesses nanosheet morphology with thickness of about 20 nm and length of several hundred nanometers. The electrochemical performances demonstrate that NaLaTi_2O_6 has a good lithium ion insertion/extraction ability with a discharge capacity of about 180 mAh/g, which is slightly larger than Li_4Ti_5O_1_2 theoretical capacity (175 mAh/g). Even more, after 1000 charge-discharge cycles at 100 mA/g, it still maintains a discharge capacity of 165 mAh/g, suggesting that NaLaTi_2O_6 could be explored as a potential anode material for lithium ion batteries.

  8. The reaction of lithium metal vapor with single walled carbon nanotubes of large diameters

    Czech Academy of Sciences Publication Activity Database

    Kalbáč, Martin; Kavan, Ladislav; Dunsch, L.

    2009-01-01

    Roč. 246, 11-12 (2009), s. 2428-2431 ISSN 0370-1972 R&D Projects: GA AV ČR IAA400400911; GA AV ČR KAN200100801; GA AV ČR IAA400400804; GA ČR GC203/07/J067; GA MŠk LC510 Institutional research plan: CEZ:AV0Z40400503 Keywords : lithium * single walled carbon nanotubes * Raman spectroscopy Subject RIV: CG - Electrochemistry Impact factor: 1.150, year: 2009

  9. Measurements of differential cross sections for the reactions 6,7Li(n,d)5,6He and 6,7Li(n,t)4,5He at 14.1 MeV

    International Nuclear Information System (INIS)

    Shirato, Shoji; Hata, Kazuhiro; Ando, Yoshiaki; Shibuya, Shinji; Shibata, Keiichi.

    1989-08-01

    A summary of our measured cross sections for the 14.1 MeV neutron-induced reactions on lithium isotopes has been presented. Our data were measured with two counter telescopes, each of which consisted of two gas proportional counters and silicon ΔE and E detectors. Measured energy spectra of deuterons and tritons from 6 Li(n,d)n 4 He and 7 Li(n,t)n 4 He, respectively, were analyzed by a simple final-state interaction theory. Measured angular distributions for these reactions as well as 6 Li(n,t) 4 He and 7 Li(n,d) 6 He were analyzed by exact finite-range distorted wave Born approximation (EFR-DWBA) calculations. Spectroscopic factors extracted from the EFR-DWBA analyses have been compared with theoretical predictions. (author)

  10. Ultradispersed Cobalt Ferrite Nanoparticles Assembled in Graphene Aerogel for Continuous Photo-Fenton Reaction and Enhanced Lithium Storage Performance.

    Science.gov (United States)

    Qiu, Bocheng; Deng, Yuanxin; Du, Mengmeng; Xing, Mingyang; Zhang, Jinlong

    2016-07-04

    The Photo-Fenton reaction is an advanced technology to eliminate organic pollutants in environmental chemistry. Moreover, the conversion rate of Fe(3+)/Fe(2+) and utilization rate of H2O2 are significant factors in Photo-Fenton reaction. In this work, we reported three dimensional (3D) hierarchical cobalt ferrite/graphene aerogels (CoFe2O4/GAs) composites by the in situ growing CoFe2O4 crystal seeds on the graphene oxide (GO) followed by the hydrothermal process. The resulting CoFe2O4/GAs composites demonstrated 3D hierarchical pore structure with mesopores (14~18 nm), macropores (50~125 nm), and a remarkable surface area (177.8 m(2 )g(-1)). These properties endowed this hybrid with the high and recyclable Photo-Fenton activity for methyl orange pollutant degradation. More importantly, the CoFe2O4/GAs composites can keep high Photo-Fenton activity in a wide pH. Besides, the CoFe2O4/GAs composites also exhibited excellent cyclic performance and good rate capability. The 3D framework can not only effectively prevent the volume expansion and aggregation of CoFe2O4 nanoparticles during the charge/discharge processes for Lithium-ion batteries (LIBs), but also shorten lithium ions and electron diffusion length in 3D pathways. These results indicated a broaden application prospect of 3D-graphene based hybrids in wastewater treatment and energy storage.

  11. Analysis of a Mathematical Model of Lithium-Sulfur Cells Part III: Electrochemical Reaction Kinetics, Transport Properties and Charging

    International Nuclear Information System (INIS)

    Ghaznavi, Mahmoudreza; Chen, P.

    2014-01-01

    Highlights: • The discharge behavior of Li-S cells in wide range of exchange current densities of electrochemical reactions is studied. • Among all reduction reactions, 1/2 S 8(l) +e − ⇌1/2 S 8 2− and 1/2 S 2 2− +e − ⇌2S 2− play the most important role in capacity performance. • Low diffusion increases the precipitation of polysulfides in separator which may block the anode surface. • Large solubility of Li 2 S is needed for the model to be able to simulate the charging process. - Abstract: Sensitivity analysis of a mathematical model of a lithium-sulfur (Li-S) battery was performed by investigating the response of the model to variation of the exchange current densities, diffusion coefficients, and cathode thickness over a wide range; the results of the analysis were used to explain the some aspects of the behavior of the system which may be seen in experiments. In particular, among all the exchange current densities, the exchange current density of the elemental sulfur reduction has the most significant effect on the discharge capacity of the cell. The variation of the diffusion coefficients was also analyzed, providing information on the non-uniformity of precipitants in the cell after discharge. An optimum cathode thickness was presented to gain the highest capacity of the cell. Finally, the simulation of charging was studied, showing that the model needs a large solubility product of di-lithium sulfide to be able to simulate the charge process of a cell

  12. Neutronigen target study and realization for medical cyclotron using proton reactions on lithium deuteride

    International Nuclear Information System (INIS)

    Filhol, J.M.

    1984-02-01

    The new idea, used for this source realization, consists of replacing the classical beryllium targets (usuals in neutronotherapy cyclotrons) by a half-thick lithium deuteride target. The target is bombarded by high energy 150 MeV) protons which are beyond the target, deviated out of the neutron beam by a permanent magnet, before to be stopped in a graphite block. Target cooling conditions study and optimisation is presented, followed by the proton deflection block study and realization. The permanent magnet used (SmCo 5 ) is adapted to this target use conditions. Many series of neutronic and dosimetric characteristics measurements allow to verify the theoretical predictions concerning the neutron flux obtained [fr

  13. Deuterium and lithium-6 MAS NMR studies of manganese oxide electrode materials

    Science.gov (United States)

    Paik, Younkee

    Electrolytic manganese dioxide (EMD) is used world wide as the cathode materials in both lithium and alkaline primary (non-rechargeable) batteries. We have developed deuterium and lithium MAS NMR techniques to study EMD and related manganese oxides and hydroxides, where diffraction techniques are of limited value due to a highly defective nature of the structures. Deuterons in EMD, manganite, groutite, and deuterium-intercalated pyrolusite and ramsdellite were detected by NMR, for the first time, and their locations and motions in the structures were analyzed by applying variable temperature NMR techniques. Discharge mechanisms of EMD in alkaline (aqueous) electrolytes were studied, in conjunction with step potential electrochemical spectroscopic (SPECS) method, and five distinctive discharge processes were proposed. EMD is usually heat-treated at about 300--400°C to remove water to be used in lithium batteries. Details of the effects of heat-treatment, such as structural and compositional changes as a function of heat-treatment temperature, were studied by a combination of MAS NMR, XRD, and thermogravimetric analysis. Lithium local environments in heat-treated EMD (HEMD) that were discharged in lithium cells, were described in terms of related environments found in model compounds pyrolusite and ramsdellite where specific Li + sites were detected by MAS NMR and the hyperfine shift scale method of Grey et al. Acid-leaching of Li2MnO3 represents an approach for synthesizing new or modified manganese oxide electrode materials for lithium rechargeable batteries. Progressive removal of lithium from specific crystallographic sites, followed by a gradual change of the crystal structure, was monitored by a combination of NMR and XRD techniques.

  14. Investigation on lithium migration for treating alkali-silica reaction affected concrete

    NARCIS (Netherlands)

    Silva De Souza, L.M.; Polder, R.B.; Copuroglu, O.

    2014-01-01

    Alkali-silica reaction (ASR) is one of the major deterioration mechanisms that affect numerous concrete structures worldwide. During the reaction, hydroxyl and alkali (sodium and potassium ) ions react with certain siliceous compounds in the aggregate, forming a hygroscopic gel. The gel absorbs

  15. Electrochemical lithium migration to mitigate alkali-silica reaction in existing concrete structures

    NARCIS (Netherlands)

    Silva De Souza, L.M.

    2016-01-01

    Alkali-silica reaction (ASR) is a deterioration process that affects the durability of concrete structures worldwide. During the reaction, hydroxyl and alkali ions present in the pore solution react with reactive silica from the aggregate, forming a hygroscopic ASR gel. Alternatively, the silica

  16. Corrosion of ferritic steels by molten lithium: Influence of competing thermal gradient mass transfer and surface product reactions

    International Nuclear Information System (INIS)

    Tortorelli, P.F.

    1987-10-01

    An Fe-12Cr-1MoVW steel was exposed to thermally convective lithium for 6962 h. Results showed that the weight change profile of Fe-12Cr-1MoVW steel changed substantially as the maximum loop temperature was raised from 500 to 600 0 C. Furthermore, for a particular loop experiment, changes in the structure and composition of the exposed surfaces did not reflect typical thermal gradient mass transfer effects for all elements: the surface concentration of chromium was often a maximum at intermediate temperatures, while nickel (present at low concentrations in the starting material) tended to be transported to the coldest part of the loop. Such data were interpreted in terms of a qualitative model in which there are different dominant reactions or the various constituents of the ferritic steels (surface product formation involving nitrogen and/or carbon and solubility-driven elemental transport). This competition among different reactions is important in evaluating overall corrosion behavior and the effects of temperature. The overall corrosion rate of the 12Cr-1MoVW steel was relatively low when compared to that for austenitic stainless steel exposed under similar conditions

  17. A Capacity Fading Model of Lithium-Ion Battery Cycle Life Based on the Kinetics of Side Reactions for Electric Vehicle Applications

    International Nuclear Information System (INIS)

    Gu, Weijun; Sun, Zechang; Wei, Xuezhe; Dai, Haifeng

    2014-01-01

    Highlights: • Describe the aging mechanism of lithium-ion battery with electrochemical kinetics. • Establish the fading rate equation based on Eyring Equation. • The established equation is applicable to any reaction order. • Integrate the internal kinetics with external degradation characteristics. - Abstract: Battery life prediction is one of the critical issues that restrict the development of electric vehicles. Among the typical battery life models, the mechanism model focusing on the internal physical or electrochemical processes has a stronger theoretical foundation and greater accuracy. The empirical formula, which relies on the simplified mechanism, has a concise model structure and more flexibility in vehicle applications. However, the internal aging mechanism rarely correlates with the external operating characteristics. Based on the summary of the capacity fading mechanism and the reasoning of the internal kinetics of side reactions during the aging process, a lifetime model of the lithium-ion battery is established in this paper. The solutions to the vital parameters based on the external accelerated life testing results are also presented. The testing sample is a manganese oxide lithium-ion battery of 8 Ah. The validation results indicated that the life model established in this paper can describe the capacity fading law of the lithium-ion battery and the operability and accuracy for vehicle applications

  18. Lithium ion diffusion measurements on a garnet-type solid conductor Li6.6La3Zr1.6Ta0.4O12 by using a pulsed-gradient spin-echo NMR method.

    Science.gov (United States)

    Hayamizu, Kikuko; Matsuda, Yasuaki; Matsui, Masaki; Imanishi, Nobuyuki

    2015-09-01

    The garnet-type solid conductor Li7-xLa3Zr2-xTaxO12 is known to have high ionic conductivity. We synthesized a series of compositions of this conductor and found that cubic Li6.6La3Zr1.6Ta0.4O12 (LLZO-Ta) has a high ionic conductivity of 3.7×10(-4)Scm(-1) at room temperature. The (7)Li NMR spectrum of LLZO-Ta was composed of narrow and broad components, and the linewidth of the narrow component varied from 0.69kHz (300K) to 0.32kHz (400K). We carried out lithium ion diffusion measurements using pulsed-field spin-echo (PGSE) NMR spectroscopy and found that echo signals were observed at T≥313K with reasonable sensitivity. The lithium diffusion behavior was measured by varying the observation time and pulsed-field gradient (PFG) strength between 313 and 384K. We found that lithium diffusion depended significantly on the observation time and strength of the PFG, which is quite different from lithium ion diffusion in liquids. It was shown that lithium ion migration in the solid conductor was distributed widely in both time and space. Copyright © 2015 Elsevier Inc. All rights reserved.

  19. Application of neutron radiography to visualize the distribution of lithium in lithium batteries

    International Nuclear Information System (INIS)

    Kamata, Masahiro; Esaka, Takao; Fujine, Sigenori; Yoneda, Kenji; Kanda, Keiji.

    1995-01-01

    The authors have tried to visualize the motion of lithium ions in lithium ion conductors such as Li 1.33 Ti 1.67 O 4 at high temperatures using neutron radiography (NR) technique and confirmed that NR is very effective to the 6 Li containing systems. This means NR may be used as a non-destructive investigating method to study the electrode reactions and the mass transfer in lithium batteries. Here in this work, it was tried to visualize the distribution of lithium in commercial lithium batteries before and after discharge using NR technique. Obtained NR images will be presented with brief explanation on NR method. Further explanations on the principle of NR and on the NR facilities were presented elsewhere. (J.P.N.)

  20. 6Li MAS NMR Study of Lithium Insertion into Hydrothermally Prepared Li-Ti-O Spinel

    Czech Academy of Sciences Publication Activity Database

    Krtil, Petr; Dědeček, Jiří; Kostlánová, Tereza; Brus, Jiří

    2004-01-01

    Roč. 7, č. 7 (2004), A163-A166 ISSN 1099-0062 R&D Projects: GA ČR GA203/03/0823 Institutional research plan: CEZ:AV0Z4040901 Keywords : lithium insertion * spinel * NMR Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.271, year: 2004

  1. Guided Lithium Metal Deposition and Improved Lithium Coulombic Efficiency through Synergistic Effects of LiAsF 6 and Cyclic Carbonate Additives

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Xiaodi [Energy; Zhang, Yaohui [Energy; Engelhard, Mark H. [Environmental; Li, Qiuyan [Energy; Zhang, Ji-Guang [Energy; Xu, Wu [Energy

    2017-11-20

    Spatial and morphology control over lithium (Li) metal nucleation/growth, as well as improving Li Coulombic efficiency (CE) are of the most challenging issues for rechargeable Li metal batteries. Here, we report that LiAsF6 and vinylene carbonate (VC) can work synergistically to address these challenges. It is revealed that AsF6- can be reduced to Li3As and LiF, which can act as seeds for Li growth and form a robust solid electrolyte interphase (SEI) layer, respectively. The addition of VC is critical because it not only enables uniform AsF6- reduction by passivating the defect sites on Cu substrate, but also improves the SEI layer flexibility during the reductive polymerization process. As a result, highly compact, uniform and dendrite-free Li film with vertically aligned columns structure can be obtained with greatly increased Li CE, and the Li metal batteries using the electrolyte with both LiAsF6 and VC additives can have much improved cycle life.

  2. Lithium-Ion (de)insertion reaction of Germanium thin-film electrodes : an electrochemical and in situ XRD study

    NARCIS (Netherlands)

    Baggetto, L.; Notten, P.H.L.

    2009-01-01

    Germanium is a promising negative electrode candidate for lithium-ion thin-film batteries because of its very high theoretical storage capacity. When assuming full conversion of the material into the room-temperature equilibrium lithium saturated germanium phase, a theoretical capacity of or of

  3. Improved the lithium storage capability of BaLi2Ti6O14 by electroless silver coating

    International Nuclear Information System (INIS)

    Lin, Xiaoting; Wang, Pengfei; Li, Peng; Yu, Haoxiang; Qian, Shangshu; Shui, Miao; Wang, Dongjie; Long, Nengbing; Shu, Jie

    2015-01-01

    Highlights: • BaLi 2 Ti 6 O 14 /Ag is fabricated via a facile electroless deposition. • Highly dispersed Ag nanoparticles are successively coated on BaLi 2 Ti 6 O 14 . • BaLi 2 Ti 6 O 14 /Ag is used as anode material for lithium storage. • BaLi 2 Ti 6 O 14 /Ag exhibits improved lithium storage capability. - Abstract: To form BaLi 2 Ti 6 O 14 /Ag, highly dispersed Ag nanoparticles are successfully deposited on the surface of BaLi 2 Ti 6 O 14 by a simple chemical deposition method. The morphology, quantity and size of Ag nanoparticles in BaLi 2 Ti 6 O 14 /Ag composites are significantly influenced by the Ag coating contents. Electrochemical results show that Ag nanoparticles play a positive role in reducing redox polarization and improving electrical conductivity of BaLi 2 Ti 6 O 14 during lithiation/delithiation processes. Among all the as-obtained products, 6 wt.% Ag coated BaLi 2 Ti 6 O 14 shows the highest initial charge specific capacity of 160 mAh g −1 at the current density of 100 mA g −1 (1C), which is much higher than the 149.1 mAh g −1 for bare BaLi 2 Ti 6 O 14 . After 100 charge/discharge cycles, the reversible capacity can be maintained at 117.0 mAh g −1 . Moreover, this sample also shows excellent rate performance with high reversible charge capacities of 147.5, 139.7, 132.6, and 126.7 mAh g −1 at the rates of 2C, 3C, 4C and 5C, respectively. Compared with bare BaLi 2 Ti 6 O 14 , the superior electrochemical performance indicates that BaLi 2 Ti 6 O 14 /Ag can be a good anode material in lithium ion batteries.

  4. Utility of Lithium in Rare-Earth Metal Reduction Reactions to Form Nontraditional Ln2+ Complexes and Unusual [Li(2.2.2-cryptand)]1+ Cations.

    Science.gov (United States)

    Huh, Daniel N; Darago, Lucy E; Ziller, Joseph W; Evans, William J

    2018-02-19

    The utility of lithium compared to other alkali metals in generating Ln 2+ rare-earth metal complexes via reduction of Ln 3+ precursors in reactions abbreviated as LnA 3 /M (Ln = rare-earth metal; A = anionic ligand; M = alkali metal) is described. Lithium reduction of Cp' 3 Ln (Cp' = C 5 H 4 SiMe 3 ; Ln = Y, Tb, Dy, Ho) under Ar in the presence of 2.2.2-cryptand (crypt) forms new examples of crystallographically characterizable Ln 2+ complexes of these metals, [Li(crypt)][Cp' 3 Ln]. In each complex, lithium is found in an N 2 O 4 donor atom coordination geometry that is unusual for the cryptand ligand. Magnetic susceptibility data on these new examples of nontraditional divalent lanthanide complexes are consistent with 4f n 5d 1 electronic configurations. The Dy and Ho complexes have exceptionally high single-ion magnetic moments, 11.35 and 11.67 μ B , respectively. Lithium reduction of Cp' 3 Y under N 2 at -35 °C forms the Y 2+ complex (Cp' 3 Y) 1- , which reduces dinitrogen upon warming to room temperature to generate the (N 2 ) 2- complex [Cp' 2 Y(THF)] 2 (μ-η 2 :η 2 -N 2 ). These results provide insight on the factors that lead to reduced dinitrogen complexes and/or stable divalent lanthanide complexes as a function of the specific reducing agent and conditions.

  5. Ultracold lithium-6 atoms in the BEC-BCS crossover: experiments and the construction of a new apparatus; Atomes de lithium-6 ultra froids dans la transition BEC-BCS: experiences et construction d'un montage experimental

    Energy Technology Data Exchange (ETDEWEB)

    Teichmann, M

    2007-09-15

    We use a fermionic gas of Lithium-6 as a model system to study superfluidity. The limiting cases of superfluidity are Bose-Einstein condensation (BEC) and superconductivity, described by the theory by Bardeen, Cooper and Schrieffer (BCS). In Lithium-6 gases, we can explore the whole range between the two cases, known as the BEC-BCS crossover, using a Feshbach resonance. We study the change of the momentum distribution of the gas in this cross-over and compare to theoretical models. We also investigate the hydrodynamic expansion, characteristic for a superfluid gas. We observe a sudden change of the ellipticity of the gas close to the transition to the superfluid phase. Moreover, we localized heteronuclear Feshbach resonances between {sup 6}Li and {sup 7}Li. We are currently constructing a second generation of the experimental setup. An new laser system, based on high power laser diodes, was developed. Changes in the vacuum chamber, including a complete reconstruction of the Zeeman slower, have increased the atomic flux, allowing us to increase the repetition rate of our experiment. Modifications of the geometry of the magnetic traps lead to a higher number of trapped atoms. (author)

  6. Ultracold lithium-6 atoms in the BEC-BCS crossover: experiments and the construction of a new apparatus; Atomes de lithium-6 ultra froids dans la transition BEC-BCS: experiences et construction d'un montage experimental

    Energy Technology Data Exchange (ETDEWEB)

    Teichmann, M

    2007-09-15

    We use a fermionic gas of Lithium-6 as a model system to study superfluidity. The limiting cases of superfluidity are Bose-Einstein condensation (BEC) and superconductivity, described by the theory by Bardeen, Cooper and Schrieffer (BCS). In Lithium-6 gases, we can explore the whole range between the two cases, known as the BEC-BCS crossover, using a Feshbach resonance. We study the change of the momentum distribution of the gas in this cross-over and compare to theoretical models. We also investigate the hydrodynamic expansion, characteristic for a superfluid gas. We observe a sudden change of the ellipticity of the gas close to the transition to the superfluid phase. Moreover, we localized heteronuclear Feshbach resonances between {sup 6}Li and {sup 7}Li. We are currently constructing a second generation of the experimental setup. An new laser system, based on high power laser diodes, was developed. Changes in the vacuum chamber, including a complete reconstruction of the Zeeman slower, have increased the atomic flux, allowing us to increase the repetition rate of our experiment. Modifications of the geometry of the magnetic traps lead to a higher number of trapped atoms. (author)

  7. Complex titanates Sr_1_-_xPb_xLi_2Ti_6O_1_4 (0≤x≤1) as anode materials for high-performance lithium-ion batteries

    International Nuclear Information System (INIS)

    Qian, Shangshu; Yu, Haoxiang; Yan, Lei; Li, Peng; Lin, Xiaoting; Wu, Yaoyao; Long, Nengbing; Shui, Miao; Shu, Jie

    2016-01-01

    Highlights: • Sr_1_-_xPb_xLi_2Ti_6O_1_4 (0≤x≤1) is prepared by a simple solid state reaction. • Sr_0_._5Pb_0_._5Li_2Ti_6O_1_4 exhibits enhanced lithium storage capability. • Sr_0_._5Pb_0_._5Li_2Ti_6O_1_4 can deliver a capacity of 141.8 mAh g"−"1 at 700 mA g"−"1. • In-situ XRD is performed to study the reversibility of Sr_1_-_xPb_xLi_2Ti_6O_1_4. - Abstract: With the Pb doping content at Sr-site increasing, a series of Sr_1_-_xPb_xLi_2Ti_6O_1_4 (x = 0, 0.25, 0.50, 0.75, 1.0) are synthesized by a simple solid-state reaction. It is found that the reversible capacity and rate capability experience a parabolic course from SrLi_2Ti_6O_1_4 to PbLi_2Ti_6O_1_4. Among all the as-prepared samples, Sr_0_._5Pb_0_._5Li_2Ti_6O_1_4 shows the best cycling and rate properties. It delivers an initial charge capacity of 163.2 mAh g"−"1 at 100 mA g"−"1 with the capacity retention of 96.08% after 100 cycles. In addition, it can also deliver a reversible capacity of 141.8 mAh g"−"1 at 700 mA g"−"1. The superior electrochemical properties of Sr_0_._5Pb_0_._5Li_2Ti_6O_1_4 are attributed to the reduced charge transfer resistance and increased lithium-ion diffusion coefficient after doping. Besides, in-situ X-ray diffraction is also performed to investigate the lithium-ion insertion/extraction behaviors of SrLi_2Ti_6O_1_4, Sr_0_._5Pb_0_._5Li_2Ti_6O_1_4 and PbLi_2Ti_6O_1_4. The observed results confirm that Sr_0_._5Pb_0_._5Li_2Ti_6O_1_4 has good structural stability and reversibility for repeated lithium storage.

  8. Raman spectral and electrochemical studies of lithium/electrolyte interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Odziemkowski, M

    1922-01-01

    Cyclic voltammetry, corrosion potential-time transients and Normal Raman spectroscopy have been employed to characterize the lithium-lithium salt, organic solvent, interfacial region. An in-situ cutting technique was developed to expose lithium metal. In-situ optical and ex-situ scanning electron microscopy (SEM) have been used to examine the morphology of the lithium electrode surface during exposure at open circuit and after anodic polarization. The main reaction product detected by in-situ Raman spectroscopy in the system/lithium/LiAsF[sub 6], tetrahydrofuran (THF) electrolyte was polytetrahydrofuran (PTHF). The conditions for the polymerization reaction in the presence of lithium metal have been determined. Tetrahydrofuran (THF) decomposition reaction mechanisms are discussed. Decomposition reaction products have been determined as arsenic (II) oxide, As[sub 2]O[sub 3] (arsenolite) and arsenious oxyfluoride AsF[sub 2]-O-AsF[sub 2]. Potentiodynamic polarization measurements revealed a substantial shift of the corrosion potential towards positive values and only a moderate increase of anodic dissolution current for in-situ cut lithium metal. Corrosion potential-time merits have been measured. The following electrolytes have been investigated: LiAsF[sub 6], LiPF[sub 6], LiClO[sub 4], and Li(CF[sub 3]SO[sub 2])[sub 2]N in THF, 2Me-THF, and propylene carbonate (PC). The transients permit the ranking of the reactivity of the electrolytes. These measurements have shed light on understanding the stability of various stability and and solvents in contact with lithium. Compared to purified electrolytes, small amounts of water shift the corrosion potential towards even more positive values. Intensive anodic cycling of a Li electrode in unpurified LiAsF[sub 6]/THF electrolyte leads to the breakdown of a surface film/films. While at the open circuit potential (OCP), water in this same electrolyte leads to crack formation in the bulk lithium electrode.

  9. Study on a prototype and by simulation of an antineutrino detector based on a lithium 6 scintillator

    International Nuclear Information System (INIS)

    Ait-Boubker, S.

    1989-01-01

    A detector based on Lithium-6 loaded liquid scintillator has been developed by the BUGEY collaboration in order to study neutrino's fundamental properties. This thesis reports on a study concerning a prototype cell of size 85x8.5x8.5 cm 3 , of the discrimination properties between neutrons and gammas and thermal neutron identification. Monte-Carlo simulation has allowed us to precise the light collection features in the cell. The last part of this memorandum deals with a cosmic detector presenting 2.5 m 2 active surface. We have obtained for this detector a very good homogenization of light response [fr

  10. Response distributions of 6LiF and 7LiF thermoluminescence dosimeters in lithium blanket assemblies

    International Nuclear Information System (INIS)

    Maekawa, Hiroshi; Kusano, Jyo-ichi; Seki, Yasushi

    1976-11-01

    Measurement of the radiation-heating rate distribution in the fusion blanket is as important as measurement of the fission-rate distribution in a fission reactor. To obtain the information of radiation heating, the response (integral glow value) distributions in pseudo-spherical lithium assemblies with and without a graphite reflector were measured with 6 LiF and 7 LiF TLD's. The measured responses are normalized to values per source neutron. Experimental error is about 35%, and the error in positions of TLD's is about +- 3 mm. The experimental results are compared with those of calculation using RADHEAT code system and ENDF/B-III data file. (auth.)

  11. Analysis of the Deposit Layer from Electrolyte Side Reaction on the Anode of the Pouch Type Lithium Ion Polymer Batteries: The Effect of State of Charge and Charge Rate

    International Nuclear Information System (INIS)

    Agubra, Victor A.; Fergus, Jeffrey W.; Fu, Rujian; Choe, Song-yul

    2014-01-01

    Highlights: • Raising the battery cycling potential increased the rate of side reaction. • Growth of deposit layer thickness at the electrode/electrolyte interface at high SOC. • A significant amount of lithium was consumed in forming the deposit layer. • Some of the lithium were “trapped” in the graphite after the discharge cycle. - Abstract: The formation of the solid electrolyte interface (SEI) layer on the surface of the anode electrode of a lithium ion battery prevents further electrolyte decomposition reaction. However, at certain battery operating conditions, the SEI breakdown leading to more electrolyte decomposition reactions that form several species on the anode electrode surface. This paper focuses on the effect of battery potential and charge rate on the decomposition side reaction on the anode electrode of a lithium ion polymer battery, as a result of the breakdown of the SEI layer. The results from this study indicate that raising the state of charge (SOC) increases the rate of the electrolyte decomposition side reaction that resulted in formation of a thick deposit layer at the electrolyte/electrolyte interface. This deposit layer contains lithium that can no longer participate in the reversible electrochemical reaction. In addition, at high cycling potential and charge rates the amount of lithium in the graphite after complete cell discharge increased due to the entrapment of lithium in the graphite. The amount of irreversible capacity loss for the batteries cycled at high potential and current correlates with the amount of trapped lithium in the graphite and the growth of the deposit layer thickness at the electrode/electrolyte interface

  12. Ultracold lithium-6 atoms in the BEC-BCS crossover: experiments and the construction of a new apparatus

    International Nuclear Information System (INIS)

    Teichmann, M.

    2007-09-01

    We use a fermionic gas of Lithium-6 as a model system to study superfluidity. The limiting cases of superfluidity are Bose-Einstein condensation (BEC) and superconductivity, described by the theory by Bardeen, Cooper and Schrieffer (BCS). In Lithium-6 gases, we can explore the whole range between the two cases, known as the BEC-BCS crossover, using a Feshbach resonance. We study the change of the momentum distribution of the gas in this cross-over and compare to theoretical models. We also investigate the hydrodynamic expansion, characteristic for a superfluid gas. We observe a sudden change of the ellipticity of the gas close to the transition to the superfluid phase. Moreover, we localized heteronuclear Feshbach resonances between 6 Li and 7 Li. We are currently constructing a second generation of the experimental setup. An new laser system, based on high power laser diodes, was developed. Changes in the vacuum chamber, including a complete reconstruction of the Zeeman slower, have increased the atomic flux, allowing us to increase the repetition rate of our experiment. Modifications of the geometry of the magnetic traps lead to a higher number of trapped atoms. (author)

  13. Depth profiling Li in electrode materials of lithium ion battery by {sup 7}Li(p,γ){sup 8}Be and {sup 7}Li(p,α){sup 4}He nuclear reactions

    Energy Technology Data Exchange (ETDEWEB)

    Sunitha, Y., E-mail: sunibarc@gmail.com; Kumar, Sanjiv

    2017-06-01

    A proton induced γ-ray emission method based on {sup 7}Li(p,γ){sup 8}Be proton capture reaction and a nuclear reaction analysis method involving {sup 7}Li(p,α){sup 4}He reaction are described for depth profiling Li in the electrode materials, graphite and lithium cobalt oxide for example, of a Li-ion battery. Depth profiling by {sup 7}Li(p,γ){sup 8}Be reaction is accomplished by the resonance at 441 keV and involves the measurement of 14.6 and 17.6 MeV γ-rays, characteristic of the reaction, by a NaI(Tl) detector. The method has a detection sensitivity of ∼0.2 at% and enables profiling up to a depth ≥20 µm with a resolution of ≥150 nm. The profiling to a fairly large depth is facilitated by the absence of any other resonance up to 1800 keV proton energy. The reaction has substantial off-resonance cross-sections. A procedure is outlined for evaluating the off-resonance yields. Interferences from fluorine and aluminium are major limitation of this depth profiling methodology. The depth profile measurement by {sup 7}Li(p,α){sup 4}He reaction, on the other hand, utilises 2–3 MeV protons and entails the detection of α-particles at 90° or 150° angles. The reaction exhibits inverse kinematics at 150°. This method, too, suffers interference from fluorine due to the simultaneous occurrence of {sup 19}F(p,α){sup 16}O reaction. Kinematical considerations show that the interference is minimal at 90° and thus is the recommended angle of detection. The method is endowed with a detection sensitivity of ∼0.1 at%, a depth resolution of ∼100 nm and a probing depth of about 30 µm in the absence and 5–8 µm in the presence of fluorine in the material. Both methods yielded comparable depth profiles of Li in the cathode (lithium cobalt oxide) and the anode (graphite) of a Li-ion battery.

  14. A method for investigation of the D("4He, γ)"6Li reaction in the Ultralow energy region under a high background

    International Nuclear Information System (INIS)

    Bystritsky, V.M.; Dudkin, G.N.; Krylov, A.R.; Gazi, S.; Huran, J.; Nechaev, B.A.; Padalko, V.N.; Sadovsky, A.B.; Tuleushev, Yu.Zh.; Filipowicz, M.; Philippov, A.V.

    2016-01-01

    The cosmological lithium problem, that is, a noticeable discrepancy between the predicted and observed abundances of lithium, is in conflict with the Standard Big Bang Nucleosynthesis model. For example, the abundance of "7Li is 2–4 times smaller than predicted by the Standard Big Bang Nucleosynthesis. As to the abundance of "6Li, recent more accurate optical investigations have yielded only the upper limit on the "6Li/"7Li ratio, which makes the problem of "6Li abundance and accordingly of disagreement with the Standard Big Bang Nucleosynthesis predictions less acute. However, experimental study of the D("4He, γ)"6Li reaction cross section is still of current importance because there is a theoretical approach predicting its anomalously large value in the region of energies below the Standard Big Bang Nucleosynthesis energy. The work is dedicated to the measurement of the cross section for the D("4He, γ)"6Li reaction proceeding in zirconium deuteride at the incident "4He"+ion energy of 36 keV. The experiment is performed at a pulsed Hall plasma accelerator with an energy spread of 20% FWHM. A method for direct measurement of the background from the reaction chain D("4He, "4He)D→D(D, n)"3He→(n, γ) and/or (n, n′γ) ending with activation of the surrounding material by neutrons is proposed and implemented in the work. An upper limit on the D("4He, γ)"6Li reaction cross section σ≤7·10"−"3"6 cm"2 at the 90% confidence level is obtained.

  15. Stability of Routine Biochemical Analytes in Whole Blood and Plasma From Lithium Heparin Gel Tubes During 6-hr Storage.

    Science.gov (United States)

    Monneret, Denis; Godmer, Alexandre; Le Guen, Ronan; Bravetti, Clotilde; Emeraud, Cecile; Marteau, Anthony; Alkouri, Rana; Mestari, Fouzi; Dever, Sylvie; Imbert-Bismut, Françoise; Bonnefont-Rousselot, Dominique

    2016-09-01

    The stability of biochemical analytes has already been investigated, but results strongly differ depending on parameters, methodologies, and sample storage times. We investigated the stability for many biochemical parameters after different storage times of both whole blood and plasma, in order to define acceptable pre- and postcentrifugation delays in hospital laboratories. Twenty-four analytes were measured (Modular® Roche analyzer) in plasma obtained from blood collected into lithium heparin gel tubes, after 2-6 hr of storage at room temperature either before (n = 28: stability in whole blood) or after (n = 21: stability in plasma) centrifugation. Variations in concentrations were expressed as mean bias from baseline, using the analytical change limit (ACL%) or the reference change value (RCV%) as acceptance limit. In tubes stored before centrifugation, mean plasma concentrations significantly decreased after 3 hr for phosphorus (-6.1% [95% CI: -7.4 to -4.7%]; ACL 4.62%) and lactate dehydrogenase (LDH; -5.7% [95% CI: -7.4 to -4.1%]; ACL 5.17%), and slightly decreased after 6 hr for potassium (-2.9% [95% CI: -5.3 to -0.5%]; ACL 4.13%). In plasma stored after centrifugation, mean concentrations decreased after 6 hr for bicarbonates (-19.7% [95% CI: -22.9 to -16.5%]; ACL 15.4%), and moderately increased after 4 hr for LDH (+6.0% [95% CI: +4.3 to +7.6%]; ACL 5.17%). Based on RCV, all the analytes can be considered stable up to 6 hr, whether before or after centrifugation. This study proposes acceptable delays for most biochemical tests on lithium heparin gel tubes arriving at the laboratory or needing to be reanalyzed. © 2016 Wiley Periodicals, Inc.

  16. A method for investigation of the D(4He, γ)6Li reaction in the Ultralow energy region under a high background

    Science.gov (United States)

    Bystritsky, V. M.; Dudkin, G. N.; Krylov, A. R.; Gazi, S.; Huran, J.; Nechaev, B. A.; Padalko, V. N.; Sadovsky, A. B.; Tuleushev, Yu. Zh.; Filipowicz, M.; Philippov, A. V.

    2016-07-01

    The cosmological lithium problem, that is, a noticeable discrepancy between the predicted and observed abundances of lithium, is in conflict with the Standard Big Bang Nucleosynthesis model. For example, the abundance of 7Li is 2-4 times smaller than predicted by the Standard Big Bang Nucleosynthesis. As to the abundance of 6Li, recent more accurate optical investigations have yielded only the upper limit on the 6Li/7Li ratio, which makes the problem of 6Li abundance and accordingly of disagreement with the Standard Big Bang Nucleosynthesis predictions less acute. However, experimental study of the D(4He, γ)6Li reaction cross section is still of current importance because there is a theoretical approach predicting its anomalously large value in the region of energies below the Standard Big Bang Nucleosynthesis energy. The work is dedicated to the measurement of the cross section for the D(4He, γ)6Li reaction proceeding in zirconium deuteride at the incident 4He+ion energy of 36 keV. The experiment is performed at a pulsed Hall plasma accelerator with an energy spread of 20% FWHM. A method for direct measurement of the background from the reaction chain D(4He, 4He)D→D(D, n)3He→(n, γ) and/or (n, n‧γ) ending with activation of the surrounding material by neutrons is proposed and implemented in the work. An upper limit on the D(4He, γ)6Li reaction cross section σ≤7·10-36 cm2 at the 90% confidence level is obtained.

  17. A method for investigation of the D({sup 4}He, γ){sup 6}Li reaction in the Ultralow energy region under a high background

    Energy Technology Data Exchange (ETDEWEB)

    Bystritsky, V.M. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Dudkin, G.N. [National Research Tomsk Polytechnic University, Tomsk (Russian Federation); Krylov, A.R. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Gazi, S.; Huran, J. [Institute of Electrical Engineering, Slovak Academy of Sciences, Bratislava (Slovakia); Nechaev, B.A.; Padalko, V.N. [National Research Tomsk Polytechnic University, Tomsk (Russian Federation); Sadovsky, A.B. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Tuleushev, Yu.Zh. [Institute of Nuclear Physics, Ministry of Power Engineering, Almaty (Kazakhstan); Filipowicz, M. [Faculty of Energy and Fuels, University of Science and Technologies, Krakow (Poland); Philippov, A.V. [Joint Institute for Nuclear Research, Dubna (Russian Federation)

    2016-07-21

    The cosmological lithium problem, that is, a noticeable discrepancy between the predicted and observed abundances of lithium, is in conflict with the Standard Big Bang Nucleosynthesis model. For example, the abundance of {sup 7}Li is 2–4 times smaller than predicted by the Standard Big Bang Nucleosynthesis. As to the abundance of {sup 6}Li, recent more accurate optical investigations have yielded only the upper limit on the {sup 6}Li/{sup 7}Li ratio, which makes the problem of {sup 6}Li abundance and accordingly of disagreement with the Standard Big Bang Nucleosynthesis predictions less acute. However, experimental study of the D({sup 4}He, γ){sup 6}Li reaction cross section is still of current importance because there is a theoretical approach predicting its anomalously large value in the region of energies below the Standard Big Bang Nucleosynthesis energy. The work is dedicated to the measurement of the cross section for the D({sup 4}He, γ){sup 6}Li reaction proceeding in zirconium deuteride at the incident {sup 4}He{sup +}ion energy of 36 keV. The experiment is performed at a pulsed Hall plasma accelerator with an energy spread of 20% FWHM. A method for direct measurement of the background from the reaction chain D({sup 4}He, {sup 4}He)D→D(D, n){sup 3}He→(n, γ) and/or (n, n′γ) ending with activation of the surrounding material by neutrons is proposed and implemented in the work. An upper limit on the D({sup 4}He, γ){sup 6}Li reaction cross section σ≤7·10{sup −36} cm{sup 2} at the 90% confidence level is obtained.

  18. Building Honeycomb-Like Hollow Microsphere Architecture in a Bubble Template Reaction for High-Performance Lithium-Rich Layered Oxide Cathode Materials.

    Science.gov (United States)

    Chen, Zhaoyong; Yan, Xiaoyan; Xu, Ming; Cao, Kaifeng; Zhu, Huali; Li, Lingjun; Duan, Junfei

    2017-09-13

    In the family of high-performance cathode materials for lithium-ion batteries, lithium-rich layered oxides come out in front because of a high reversible capacity exceeding 250 mAh g -1 . However, the long-term energy retention and high energy densities for lithium-rich layered oxide cathode materials require a stable structure with large surface areas. Here we propose a "bubble template" reaction to build "honeycomb-like" hollow microsphere architecture for a Li 1.2 Mn 0.52 Ni 0.2 Co 0.08 O 2 cathode material. Our material is designed with ca. 8-μm-sized secondary particles with hollow and highly exposed porous structures that promise a large flexible volume to achieve superior structure stability and high rate capability. Our preliminary electrochemical experiments show a high capacity of 287 mAh g -1 at 0.1 C and a capacity retention of 96% after 100 cycles at 1.0 C. Furthermore, the rate capability is superior without any other modifications, reaching 197 mAh g -1 at 3.0 C with a capacity retention of 94% after 100 cycles. This approach may shed light on a new material engineering for high-performance cathode materials.

  19. A Chemical-Adsorption Strategy to Enhance the Reaction Kinetics of Lithium-Rich Layered Cathodes via Double-Shell Surface Modification.

    Science.gov (United States)

    Guo, Lichao; Li, Jiajun; Cao, Tingting; Wang, Huayu; Zhao, Naiqin; He, Fang; Shi, Chunsheng; He, Chunnian; Liu, Enzuo

    2016-09-21

    Sluggish surface reaction kinetics hinders the power density of Li-ion battery. Thus, various surface modification techniques have been applied to enhance the electronic/ionic transfer kinetics. However, it is challenging to obtain a continuous and uniform surface modification layer on the prime particles with structure integration at the interface. Instead of classic physical-adsorption/deposition techniques, we propose a novel chemical-adsorption strategy to synthesize double-shell modified lithium-rich layered cathodes with enhanced mass transfer kinetics. On the basis of experimental measurement and first-principles calculation, MoO2S2 ions are proved to joint the layered phase via chemical bonding. Specifically, the Mo-O or Mo-S bonds can flexibly rotate to bond with the cations in the layered phase, leading to the good compatibility between the thiomolybdate adsorption layer and layered cathode. Followed by annealing treatment, the lithium-excess-spinel inner shell forms under the thiomolybdate adsorption layer and functions as favorable pathways for lithium and electron. Meanwhile, the nanothick MoO3-x(SO4)x outer shell protects the transition metal from dissolution and restrains electrolyte decomposition. The double-shell modified sample delivers an enhanced discharge capacity almost twice as much as that of the unmodified one at 1 A g(-1) after 100 cycles, demonstrating the superiority of the surface modification based on chemical adsorption.

  20. Search for possible 6-q states via inclusive reactions

    International Nuclear Information System (INIS)

    Bhatia, T.S.

    1984-01-01

    A satisfactory understanding of the 6-q system is necessary for a complete understanding of the short-range part of the NN interaction. Bag models and quark potential models predict 6-q states in the 2 to 3 GeV mass range. NNπ and NNππ are examples of 6-q states involving the same quark flavors as the NN system, search for which could be undertaken through inclusive spin-dependent measurements

  1. Destabilization of the 6H-SrIrO3 polymorph through partial substitution of zinc and lithium

    DEFF Research Database (Denmark)

    Bremholm, Martin; K. Kim, Cindi; Hirai, Daigo

    2012-01-01

    We report on the destabilization of the 6H-SrIrO3 polymorph through partial substitutions of zinc and lithium for iridium to form perovskites. The perovskites crystallize in the orthorhombic space group Pbnm: SrIr1−xZnxO3 is found for 0.25 ≤ x ≤ 0.33, while SrIr1−xLixO3 is found only for x = 0...... show Curie–Weiss behavior, with relatively large temperature independent contributions, and that the iridium atoms have low effective moments, 0.52 to 1.08 μB per Ir. The resistivity of SrIr0.67Zn0.33O3, characterized by Mott variable range hopping type semiconducting behavior, indicates...

  2. Synthesis and Electrochemical Properties of Fe-doped V6O13 as Cathode Material for Lithium-ion Battery

    Directory of Open Access Journals (Sweden)

    YUAN Qi

    2018-01-01

    Full Text Available Fe-doped V6O13 was synthesized via a facile hydrothermal method after preparing precursor in order to improve the discharge capacity and cycle performance of V6O13 cathode material at high-lithium state. XRD, SEM and XPS were employed to characterize the phase, morphology and valence of the Fe-doped V6O13. Meanwhile, the electrochemical performance was analyzed and researched. Different morphologies and electrochemical performances of Fe-doped V6O13 were obtained via doping different contents of Fe3+ ion. The sample 0.02 presented the largest thickness of nanosheets (the thickness of 600-900nm and clearance between layers. The Fe-doped V6O13 has a better electrochemical performance than that of pure V6O13. The sample 0.02 exhibits the best electrochemical performance, the initial discharge specific capacity is 433mAh·g-1 and the capacity retention is 47.1% after 100 cycles.

  3. Effect of cathode porosity on the Lithium-air cell oxygen reduction reaction – A rotating ring-disk electrode investigation

    International Nuclear Information System (INIS)

    Seo, Jeongwook; Sankarasubramanian, Shrihari; Singh, Nikhilendra; Mizuno, Fuminori; Takechi, Kensuke; Prakash, Jai

    2017-01-01

    The kinetics of the oxygen reduction reaction (ORR) on the practical air cathode in a Lithium-air cell, which is conventionally composed of porous carbon with or without catalysts supported on it, was investigated. The mechanism and kinetics of the oxygen reduction reaction (ORR) was studied on a porous carbon electrode in an oxygen saturated solution of 0.1 M Lithium bis-trifluoromethanesulfonimide (LiTFSI) in Dimethoxyethane (DME) using cyclic voltammetery (CV) and the rotating ring-disk electrode (RRDE) technique. The oxygen reduction and evolution reactions were found to occur at similar potentials to those observed on a smooth, planar glassy carbon (GC) electrode. The effect of porosity and the resultant increase in surface area were readily observed in the increase in the transient time required for the intermediates to reach the ring and the much larger disk currents (compared to smooth, planar GC) recorded respectively. The RRDE data was analyzed using a kinetic model previously developed by us and the rate constants for the elementary reactions were calculated. The rates constant for the electrochemical reactions were found to be similar in magnitude to the rate constants calculated for smooth GC disks. The porosity of the electrode was found to decrease the rate of desorption of the intermediate and the product and delay their diffusion by shifting it from a Fickian regime in the electrolyte bulk to the Knudsen regime in the film pores. Thus, it is shown that the effect of the electrode porosity on the kinetics of the ORR is physical rather than electrochemical.

  4. Hydrogen Outgassing from Lithium Hydride

    Energy Technology Data Exchange (ETDEWEB)

    Dinh, L N; Schildbach, M A; Smith, R A; Balazs1, B; McLean II, W

    2006-04-20

    Lithium hydride is a nuclear material with a great affinity for moisture. As a result of exposure to water vapor during machining, transportation, storage and assembly, a corrosion layer (oxide and/or hydroxide) always forms on the surface of lithium hydride resulting in the release of hydrogen gas. Thermodynamically, lithium hydride, lithium oxide and lithium hydroxide are all stable. However, lithium hydroxides formed near the lithium hydride substrate (interface hydroxide) and near the sample/vacuum interface (surface hydroxide) are much less thermally stable than their bulk counterpart. In a dry environment, the interface/surface hydroxides slowly degenerate over many years/decades at room temperature into lithium oxide, releasing water vapor and ultimately hydrogen gas through reaction of the water vapor with the lithium hydride substrate. This outgassing can potentially cause metal hydriding and/or compatibility issues elsewhere in the device. In this chapter, the morphology and the chemistry of the corrosion layer grown on lithium hydride (and in some cases, its isotopic cousin, lithium deuteride) as a result of exposure to moisture are investigated. The hydrogen outgassing processes associated with the formation and subsequent degeneration of this corrosion layer are described. Experimental techniques to measure the hydrogen outgassing kinetics from lithium hydride and methods employing the measured kinetics to predict hydrogen outgassing as a function of time and temperature are presented. Finally, practical procedures to mitigate the problem of hydrogen outgassing from lithium hydride are discussed.

  5. Energetics of the lithium-magnesium imide-magnesium amide and lithium hydride reaction for hydrogen storage: An ab initio study

    International Nuclear Information System (INIS)

    Velikokhatnyi, Oleg I.; Kumta, Prashant N.

    2007-01-01

    An ab initio study within the density functional theory of the recently described reversible hydrogen storage reaction Mg(NH 2 ) 2 + 2LiH ↔ Li 2 Mg(NH) 2 + 2H 2 has been conducted. The electronic structure, structural parameters, vibrational spectra, and enthalpies of formation of all the reactants and products as well as the heat of the overall reaction at zero and finite temperature have been calculated in the generalized gradient approximation (GGA) to the exchange correlation potential. The heat of the overall reaction is calculated to be 53.4 kJ/mol H 2 in contrast to the experimentally obtained overall heat of reaction of ∼44.1 kJ/mol H 2 . The difference of ∼20% between the experimental and calculated values is discussed

  6. Application of C_6_0, C_7_2 and carbon nanotubes as anode for lithium-ion batteries: A DFT study

    International Nuclear Information System (INIS)

    Najafi, Meysam

    2017-01-01

    The application of C_6_0, C_7_2, CNT (8, 0) and CNT (10, 0) as anode materials for Lithium-ion batteries were investigated by density functional theory (DFT) calculations. Results show that the average values of voltage cell (V_c_e_l_l) and adsorption energy (E_a_d) of CNT (8, 0) and CNT (10, 0) were higher than C_6_0 and C_7_2 ca 0.327 V and 6.52 kcal/mol, respectively. The NH_2 functionalization of studied nanostructures as a strategy to improve the performance of these systems as anode materials of Lithium-ion batteries were investigated. Results show that, NH_2 functionalization of studied nanostructures increase the average values of voltage cell and adsorption energy ca 0.197 V and 8.20 kcal/mol, respectively. Obtained results propose that NH_2 functionalized C_7_2 and CNT (10, 0) have larger V_c_e_l_l and E_a_d values and therefore these nanostructures have higher potential as anode material for Lithium-ion battery. - Highlights: • C_6_0 and CNT (10, 0) as anode materials for Lithium-ion batteries were investigated. • V_c_e_l_l and E_a_d of CNT (8, 0) and CNT (10, 0) were higher than C_6_0 and C_7_2 ca. • NH_2 functionalization of C_6_0 improve the performance of it as anode materials of Lithium-ion batteries.

  7. Search for the signature of a halo structure in the p(6He,6Li)n reaction

    International Nuclear Information System (INIS)

    Cortina-Gil, M.D.; Roussel-Chomaz, P.; Mittig, W.; Casandjian, J.M.; Chartier, M.; Alamanos, N.; Auger, F.; Fekou-Youmbi, V.; Blumenfeld, Y.; and others.

    1995-01-01

    The elastic scattering p( 6 He, 6 He)p and charge exchange reaction p( 6 He, 6 Li)n have been measured in reverse kinematics with a secondary 6 He beam. The angular distributions for these reactions were obtained. In the case of the charge exchange reaction, the ratio of the cross section for the Gamow-Teller transition to the ground state, and for the Fermi transition to the isobaric analog state is a measure of the relative strength of the two components of the exchange interaction. This ratio is found compatible with existing systematics for stable T=1 nuclei, and no clear signature of a halo structure was found in the present data. (author)

  8. Study of surface reaction of spinel Li4Ti5O12 during the first lithium insertion and extraction processes using atomic force microscopy and analytical transmission electron microscopy.

    Science.gov (United States)

    Kitta, Mitsunori; Akita, Tomoki; Maeda, Yasushi; Kohyama, Masanori

    2012-08-21

    Spinel lithium titanate (Li(4)Ti(5)O(12), LTO) is a promising anode material for a lithium ion battery because of its excellent properties such as high rate charge-discharge capability and life cycle stability, which were understood from the viewpoint of bulk properties such as small lattice volume changes by lithium insertion. However, the detailed surface reaction of lithium insertion and extraction has not yet been studied despite its importance to understand the mechanism of an electrochemical reaction. In this paper, we apply both atomic force microscopy (AFM) and transmission electron microscopy (TEM) to investigate the changes in the atomic and electronic structures of the Li(4)Ti(5)O(12) surface during the charge-discharged (lithium insertion and extraction) processes. The AFM observation revealed that irreversible structural changes of an atomically flat Li(4)Ti(5)O(12) surface occurs at the early stage of the first lithium insertion process, which induces the reduction of charge transfer resistance at the electrolyte/Li(4)Ti(5)O(12) interface. The TEM observation clarified that cubic rock-salt crystal layers with a half lattice size of the original spinel structure are epitaxially formed after the first charge-discharge cycle. Electron energy loss spectroscopy (EELS) observation revealed that the formed surface layer should be α-Li(2)TiO(3). Although the transformation of Li(4)Ti(5)O(12) to Li(7)Ti(5)O(12) is well-known as the lithium insertion reaction of the bulk phase, the generation of surface product layers should be inevitable in real charge-discharge processes and may play an effective role in the stable electrode performance as a solid-electrolyte interphase (SEI).

  9. PP: A graphics post-processor for the EQ6 reaction path code

    International Nuclear Information System (INIS)

    Stockman, H.W.

    1994-09-01

    The PP code is a graphics post-processor and plotting program for EQ6, a popular reaction-path code. PP runs on personal computers, allocates memory dynamically, and can handle very large reaction path runs. Plots of simple variable groups, such as fluid and solid phase composition, can be obtained with as few as two keystrokes. Navigation through the list of reaction path variables is simple and efficient. Graphics files can be exported for inclusion in word processing documents and spreadsheets, and experimental data may be imported and superposed on the reaction path runs. The EQ6 thermodynamic database can be searched from within PP, to simplify interpretation of complex plots

  10. A stable organic-inorganic hybrid layer protected lithium metal anode for long-cycle lithium-oxygen batteries

    Science.gov (United States)

    Zhu, Jinhui; Yang, Jun; Zhou, Jingjing; Zhang, Tao; Li, Lei; Wang, Jiulin; Nuli, Yanna

    2017-10-01

    A stable organic-inorganic hybrid layer (OIHL) is direct fabricated on lithium metal surface by the interfacial reaction of lithium metal foil with 1-chlorodecane and oxygen/carbon dioxide mixed gas. This favorable OIHL is approximately 30 μm thick and consists of lithium alkyl carbonate and lithium chloride. The lithium-oxygen batteries with OIHL protected lithium metal anode exhibit longer cycle life (340 cycles) than those with bare lithium metal anode (50 cycles). This desirable performance can be ascribed to the robust OIHL which prevents the growth of lithium dendrites and the corrosion of lithium metal.

  11. Role of adenylyl cyclase 6 in the development of lithium-induced nephrogenic diabetes insipidus

    DEFF Research Database (Denmark)

    Poulsen, Søren Brandt; Kristensen, Tina Bøgelund; Brooks, Heddwen L

    2017-01-01

    knockout (AC6(loxloxCre)) mice had approximately 50% lower urine osmolality and doubled water intake under baseline conditions compared with controls. Dietary Li(+) administration increased water intake and reduced urine osmolality in control, AC6(-/-), and AC6(loxloxCre) mice. Consistent with AC6......(-/-) mice, medullary AQP2 and pS256-AQP2 abundances were lower in AC6(loxloxCre) mice compared with controls under standard conditions, and levels were further reduced after Li(+) administration. AC6(loxloxCre) and control mice had a similar increase in the numbers of proliferating cell nuclear antigen......-positive cells in response to Li(+). However, AC6(loxloxCre) mice had a higher number of H(+)-ATPase B1 subunit-positive cells under standard conditions and after Li(+) administration. Collectively, AC6 has a minor role in Li-NDI development but may be important for determining the intercalated cell...

  12. Investigation of the antiprotonic X-ray spectrum of the lithium isotopes 6Li and 7Li

    International Nuclear Information System (INIS)

    Guigas, R.

    1981-09-01

    Antiprotons of the low-energy separated anti p-beam K 23 at CERN in Geneva have been stopped in thin (0.6 g/cm 2 ) targets of the Lithium isotopes 6 Li and 7 Li. The characteristic X-rays of the formed antiprotonic atoms were measured with four identical high-resolution Si (Li) detectors. Three lines of the N- series, four lines of the M-series and the 3d-2p transition of the Balmer series were observed. The measured relative intensities of the M- and N-series transitions are well described by the simple cascade model of Eisenberg and Kessler. The 3d-2p transition is considerably influenced by the strong interaction between antiproton and nucleus and thus drastically reduced in intensity. The analysis of this transition yields the shift and width of the 2p level, whereas the width of the 3d level is deduced from intensity considerations. (orig./HSI)

  13. Effect of compound nuclear reaction mechanism in 12C(6Li,d) reaction at sub-Coulomb energy

    Science.gov (United States)

    Mondal, Ashok; Adhikari, S.; Basu, C.

    2017-09-01

    The angular distribution of the 12C(6Li,d) reaction populating the 6.92 and 7.12 MeV states of 16O at sub-Coulomb energy (Ecm=3 MeV) are analysed in the framework of the Distorted Wave Born Approximation (DWBA). Recent results on excitation function measurements and backward angle angular distributions derive ANC for both the states on the basis of an alpha transfer mechanism. In the present work, we show that considering both forward and backward angle data in the analysis, the 7.12 MeV state at sub-Coulomb energy is populated from Compound nuclear process rather than transfer process. The 6.92 MeV state is however produced from direct reaction mechanism.

  14. Differential cross section measurement for the 6Li(n,t)4He Reaction

    International Nuclear Information System (INIS)

    Zhang Guohui; Tang Guoyou; Chen Jinxiang; Shi Zhaomin

    2002-01-01

    The differential cross sections and integrated cross sections of the 6 Li(n,t) 4 He reaction were measured at 1.85 and 2.67 MeV by using a gridded ionization chamber. Neutrons were produced through the T(p, n) 3 He reaction. The absolute neutron flux was determined through the 238 U(n, f) reaction. Present results are compared with existing data

  15. Differential cross section measurement for the {sup 6}Li(n,t){sup 4}He Reaction

    Energy Technology Data Exchange (ETDEWEB)

    Guohui, Zhang; Guoyou, Tang; Jinxiang, Chen; Zhaomin, Shi [Beijing Univ., Beijing (China). Inst. of Heavy Ion Physics and MOE Key Laboratory of Heavy Ion Physics; Zemin, Chen [Tsinghua Univ., Beijing (China). Dept. of Physics; Gledenov, Yu M; Sedysheva, M; Khuukhenkhuu, G [Joint Institute for Nuclear Research, Frank Laboratory of Neutron Physics, Dubna (Russian Federation)

    2002-06-01

    The differential cross sections and integrated cross sections of the {sup 6}Li(n,t){sup 4}He reaction were measured at 1.85 and 2.67 MeV by using a gridded ionization chamber. Neutrons were produced through the T(p, n){sup 3}He reaction. The absolute neutron flux was determined through the {sup 238}U(n, f) reaction. Present results are compared with existing data.

  16. [Profile of lithium carbonate use in patients with bipolar disorder in Colombia].

    Science.gov (United States)

    Machado-Duque, Manuel Enrique; Alzate-Carvajal, Catalina; Zapata-Castañeda, Kevin; Machado-Alba, Jorge Enrique

    2017-04-01

    Lithium is the drug of choice for the treatment of bipolar affective disorder. To define lithium therapeutic profile and adverse reactions to its use in patients with bipolar affective disorder in Colombia. We conducted an observational retrospective cohort study between January 1 and December 31, 2013, which included patients with a diagnosis of bipolar disorder treated with lithium carbonate in 25 Colombian cities; we evaluated socio-demographic variables, lithium dose, co-medication, drug interactions and adverse reactions. A multivariate analysis was done using SPSS 22.0. The 331 patients had an average age of 44.5 ± 13.9 years; 59.2% were women. The mean dose of lithium was 898 ± 294 mg/day; 22% received doses lower than recommended, and patients had received lithium for 38.0 ± 39.5 months (range: 12-159 months). Lithium levels in blood had been measured only in 13.5% of patients; 71.3% of them had received adjuvant therapy for bipolar disorder with other drugs, especially clozapine (16.6%) and valproic acid (16.6%). The main comorbidities were hypothyroidism (18.1%) and hypertension (12.7%); 390 potentially toxic drug interactions were found, and adverse reactions were reported in 1.2% of patients. A statistically significant association was found between a lower risk of combination therapy and receiving treatment in the cities of Bogotá (OR=0.4, p=0.025), Cartagena (OR=0.3, p=0.015) and Ibagué (OR=0.3, p=0.025). Lithium was generally used at recommended doses and intervals, but a significant percentage of patients received lower doses than those recommended, and it was not possible to compare with lithium levels in blood. Adverse reactions and blood lithium levels reporting should be improved in patients with bipolar disorder in Colombia.

  17. Hydrophobic ionic liquids based on the 1-butyl-3-methylimidazolium cation for lithium/seawater batteries

    Science.gov (United States)

    Zhang, Yancheng; Urquidi-Macdonald, Mirna

    Two hydrophobic ionic liquids (room temperature molten salts) based on 1-butyl-3-methylimidazolium cation (BMI +), BMI +PF 6- and BMI +Tf 2N -, were used in developing a highly efficient lithium anode system for lithium/seawater batteries. The lithium anode system was composed of lithium metal/ionic liquid/Celgard membrane. Both BMI +PF 6-and BMI +Tf 2N - maintained high apparent anodic efficiency (up to 100%) under potentiostatic polarization (at +0.5 V versus open-circuit potential (OCP)) in a 3% NaCl solution. Eventually, traces of water contaminated the ionic liquid and a bilayer film (LiH and LiOH) on the lithium surface was formed, decreasing the rate of lithium anodic reaction and hence the discharge current density. BMI +Tf 2N - prevented traces of water from reaching the lithium metal surface longer than BMI +PF 6- (60 h versus 7 h). However, BMI +PF 6- was better than BMI +Tf 2N - in keeping a constant current density (˜0.2 mA cm -2) before the traces of water contaminated the lithium surface due to the non-reactivity of BMI +PF 6- with the lithium metal that kept the bare lithium surface. During the discharge process, BMI +PF 6- and BMI +Tf 2N - acted as ion transport media of Li +, Cl -, OH - and H 2O, but did not react with them because of the excellent chemical stability, high conductivity, and high hydrophobicity of these two ionic liquids. Both BMI +PF 6- and BMI +Tf 2N - gels were tentative approaches used to delay the traces of water coming in contact with the lithium surface.

  18. Enriched lithium collection from lithium plasma flow

    International Nuclear Information System (INIS)

    Karchevsky, A.I.; Laz'ko, V.S.; Muromkin, Y.A.; Pashkovsky, V.G.; Ustinov, A.L.; Dolgolenko, D.A.

    1994-01-01

    In order to understand the physical processes concerned with the selective heating by ion cyclotron resonance and with the subsequent collection of heated particles, experiments were carried out with the extraction of lithium samples, enriched with 6 Li isotopes. Probe and integral extractors allow to collect enriched Li at the end of the selective heating region. Surface density distribution on the collector and local isotopic content of lithium are measured, as a function of the screen height and the retarding potential. Dependence of the collected amount of lithium and of its isotopic content on the value of the magnetic field is also measured. 4 figs., 2 tabs., 5 refs

  19. Production of lactic acid from C6-polyols by alkaline hydrothermal reactions

    International Nuclear Information System (INIS)

    Zhou Huazhen; Jin Fangming; Wu Bing; Cao Jianglin; Duan Xiaokun; Kishita, Atsushi

    2010-01-01

    Production of lactic acid from C6-polyols (Mannitol) under alkaline hydrothermal conditions was investigated. Experiments were performed to examine the difference in the production of lactic acid between C6-polyols and C3-polyols (glycerine), as well as C6-aldoses (glucose). Results showed that the yield of lactic acid from C6-polyols was lower than that from both glycerine and glucose. It indicated that long chain polyols might follow a different reaction pathway from that of glycerine. Further investigation is needed to clarify the reaction mechanism and improve the relatively low lactic acid acid yield from C6-polyols.

  20. A Unique Failure Mechanism in the Nexus 6P Lithium-Ion Battery

    OpenAIRE

    Saurabh Saxena; Yinjiao Xing; Michael Pecht

    2018-01-01

    Nexus 6P smartphones have been beset by battery drain issues, which have been causing premature shutdown of the phone even when the charge indicator displays a significant remaining runtime. To investigate the premature battery drain issue, two Nexus 6P smartphones (one new and one used) were disassembled and their batteries were evaluated using computerized tomography (CT) scan analysis, electrical performance (capacity, resistance, and impedance) tests, and cycle life capacity fade tests. T...

  1. Synthesis and Electrochemical Performance of a Lithium Titanium Phosphate Anode for Aqueous Lithium-Ion Batteries

    KAUST Repository

    Wessells, Colin; La Mantia, Fabio; Deshazer, Heather; Huggins, Robert A.; Cui, Yi

    2011-01-01

    Lithium-ion batteries that use aqueous electrolytes offer safety and cost advantages when compared to today's commercial cells that use organic electrolytes. The equilibrium reaction potential of lithium titanium phosphate is -0.5 V with respect

  2. Measurement of the 6He Decay Produced by the 9Be(n, α) 6 He Reaction

    Science.gov (United States)

    Cook, Katelyn; Coats, Micah; Yuly, Mark; Padalino, Stephen; Sangster, Craig; Regan, Sean

    2016-10-01

    The OMEGA laser at LLE is routinely used to implode gas-filled capsules to study light ion fusion reaction rates of interest to stellar nucleosynthesis. As a first step toward a possible measurement of the 3H(t,γ)6He radiative capture reaction, a detector system capable of measuring the 801 ms half-life of 6He has been developed and is being tested using 6He nuclei produced via the 9Be(n,α)6He reaction. Deuterons from the SUNY Geneseo tandem Pelletron produce neutrons in a thick deuterated polyethylene target via the 2H(d,n)3He reaction. These neutrons are allowed to strike a beryllium target placed in front of a silicon ΔE-E detector telescope, which is used to identify the β particles from 6He decay. Following an approximately five second long activation period, the beryllium sample is immediately counted for about five seconds. The pulse heights for each detector and the timestamp are recorded using a specially configured femtoDAQ acquision system and used to measure the decay curve. Funded in part by a Grant from the DOE through the Laboratory for Laser Energetics.

  3. Unique Fe2P Nanoparticles Enveloped in Sandwichlike Graphited Carbon Sheets as Excellent Hydrogen Evolution Reaction Catalyst and Lithium-Ion Battery Anode.

    Science.gov (United States)

    Zhang, Yan; Zhang, Huijuan; Feng, Yangyang; Liu, Li; Wang, Yu

    2015-12-09

    The novel Fe2P nanoparticles encapsulated in sandwichlike graphited carbon envelope nanocomposite (Fe2P/GCS) that can be first applied in hydrogen evolution reaction (HER) as well as lithium-ion batteries (LIBs) has been designed and fabricated. The unique sandwiched Fe2P/GCS is characterized with several prominent merits, including large specific surface area, nanoporous structure, excellent electronic conductivity, enhanced structural integrity and so on. All of these endow the Fe2P/GCS with brilliant electrochemical performance. When used as a HER electrocatalyst in acidic media, the harvested Fe2P/GCS demonstrates low onset overpotential and Tafel slope as well as particularly outstanding durability. Moreover, as an anode material for LIBs, the sandwiched Fe2P/GCS presents high specific capacity and excellent cyclability and rate capability. As a consequence, the acquired Fe2P/GCS is a promising material for energy applications, especially HER and LIBs.

  4. The d-α elastic scattering and the lithium-6 in a three-body model with separable interactions

    International Nuclear Information System (INIS)

    Charnomordic, Brigitte.

    1976-01-01

    This work consists in a three-body treatment of the six nucleon system. The model is constructed by considering two identical nucleons and a structureless alpha particle. Such a system can be described by the Faddeev-Lovelace equations. A partial antisymetrization is performed taking into account the identity of the nucleons. Pairwise interacting particles with nonlocal separable forces are introduced. Two-body potentials are chosen in each n-n and n-α partial wave. After an analysis of the existing separable interactions, new n-α and 1S0 parametrization are constructed. The sensitivity to the tensor force and the role of the N-α description are especially studied. The case of d-α elastic scattering is also discussed. The observables: differential cross-section, analyzing powers and transfer polarization coefficients are calculated and compared with experiments. The results show the ability of a three-body model with separable interactions in describing the main properties of the d-α elastic scattering and lithium-6 [fr

  5. SoLid: Search for Oscillations with Lithium-6 Detector at the SCK-CEN BR2 reactor

    Science.gov (United States)

    Ban, G.; Beaumont, W.; Buhour, J. M.; Coupé, B.; Cucoanes, A. S.; D'Hondt, J.; Durand, D.; Fallot, M.; Fresneau, S.; Giot, L.; Guillon, B.; Guilloux, G.; Janssen, X.; Kalcheva, S.; Koonen, E.; Labare, M.; Moortgat, C.; Pronost, G.; Raes, L.; Ryckbosch, D.; Ryder, N.; Shitov, Y.; Vacheret, A.; Van Mulders, P.; Van Remortel, N.; Weber, A.; Yermia, F.

    2016-04-01

    Sterile neutrinos have been considered as a possible explanation for the recent reactor and Gallium anomalies arising from reanalysis of reactor flux and calibration data of previous neutrino experiments. A way to test this hypothesis is to look for distortions of the anti-neutrino energy caused by oscillation from active to sterile neutrino at close stand-off (˜ 6- 8m) of a compact reactor core. Due to the low rate of anti-neutrino interactions the main challenge in such measurement is to control the high level of gamma rays and neutron background. The SoLid experiment is a proposal to search for active-to-sterile anti-neutrino oscillation at very short baseline of the SCK•CEN BR2 research reactor. This experiment uses a novel approach to detect anti-neutrino with a highly segmented detector based on Lithium-6. With the combination of high granularity, high neutron-gamma discrimination using 6LiF:ZnS(Ag) and precise localization of the Inverse Beta Decay products, a better experimental sensitivity can be achieved compared to other state-of-the-art technology. This compact system requires minimum passive shielding allowing for very close stand off to the reactor. The experimental set up of the SoLid experiment and the BR2 reactor will be presented. The new principle of neutrino detection and the detector design with expected performance will be described. The expected sensitivity to new oscillations of the SoLid detector as well as the first measurements made with the 8 kg prototype detector deployed at the BR2 reactor in 2013-2014 will be reported.

  6. Solid solution lithium alloy cermet anodes

    Science.gov (United States)

    Richardson, Thomas J.

    2013-07-09

    A metal-ceramic composite ("cermet") has been produced by a chemical reaction between a lithium compound and another metal. The cermet has advantageous physical properties, high surface area relative to lithium metal or its alloys, and is easily formed into a desired shape. An example is the formation of a lithium-magnesium nitride cermet by reaction of lithium nitride with magnesium. The reaction results in magnesium nitride grains coated with a layer of lithium. The nitride is inert when used in a battery. It supports the metal in a high surface area form, while stabilizing the electrode with respect to dendrite formation. By using an excess of magnesium metal in the reaction process, a cermet of magnesium nitride is produced, coated with a lithium-magnesium alloy of any desired composition. This alloy inhibits dendrite formation by causing lithium deposited on its surface to diffuse under a chemical potential into the bulk of the alloy.

  7. Measurement of the neutron spectrum of the Big Ten critical assembly by lithium-6 spectrometry

    International Nuclear Information System (INIS)

    De Leeuw-Gierts, G.; De Leeuw, S.; Hansen, G.E.; Helmick, H.H.

    1979-01-01

    The central neutron-flux spectrum of the Los Alamos Scientific Laboratory's critical assembly, Big Ten, was measured with a 6 Li spectrometer and techniques developed at the Centre d'Etude de L'Energie Nucleaire, Mol, as part of an experimental program to establish the characteristics of Big Ten

  8. Measurement of the neutron spectrum of the Big Ten critical assembly by lithium-6 spectrometry

    International Nuclear Information System (INIS)

    Leeuw-Gierts, G. de; Leeuw, S. de

    1980-01-01

    The central neutron-flux spectrum of the Los Alamos Scientific Laboratory's critical assembly, Big Ten, was measured with a 6 Li spectrometer and techniques developed at the Centre d'Etude de l'Energie Nucleaire, Mol, as part of an experimental program to establish the characteristics of Big Ten

  9. Fusion and nonfusion phenomena in the 6Li+40Ca reaction at 156 MeV

    International Nuclear Information System (INIS)

    Brzychczyk, J.; Freindl, L.; Grotowski, K.

    1982-01-01

    Reaction products from 6 Li-induced reactions on 40 Ca at 156 MeV have been studied using the dE x E identification as well as the inclusive γ-ray method. The complete fusion cross-section has been found to be σsub(f)=(77 +- 11)mb. The Z distribution of fusion evaporation residues is compared with statistical model predictions. The Z spectrum of reaction products shows a maximum at 15 6 Li break-up. (author)

  10. Fusion and nonfusion phenomena in the 6Li+40Ca reaction at 156 MeV

    International Nuclear Information System (INIS)

    Brzychczyk, J.; Freindl, L.; Grotowski, K.; Majka, Z.; Micek, S.; Planeta, R.; Uniwersytet Jagiellonski, Krakow; Albinska, M.; Buschmann, J.; Klewe-Nebenius, H.; Gils, H.J.; Rebel, H.; Zagromski, S.

    1984-01-01

    Reaction products from 6 Li-induced reactions on 40 Ca at 156 MeV have been studied using the dExE idenitification as well as the inclusive γ-ray method. The complete fusion cross section has been found to be sigmasub(F)=67 +- 20 mb. The Z-distribution of fusion evaporation residues is compared with statistical model predictions. The Z-spectrum of reaction products shows a maximum at 15 6 Li-break-up processes. (orig.)

  11. 6,7Li + 28Si total reaction cross sections at near barrier energies

    International Nuclear Information System (INIS)

    Pakou, A.; Musumarra, A.; Pierroutsakou, D.; Alamanos, N.; Assimakopoulos, P.A.; Divis, N.; Doukelis, G.; Gillibert, A.; Harissopulos, S.; Kalyva, G.; Kokkoris, M.; Lagoyannis, A.; Mertzimekis, T.J.; Nicolis, N.G.; Papachristodoulou, C.; Perdikakis, G.; Roubos, D.; Rusek, K.; Spyrou, S.; Zarkadas, Ch.

    2007-01-01

    Total reaction cross section measurements for the 6,7 Li + 28 Si systems have been performed at near-barrier energies. The results indicate that, with respect to the potential anomaly at barrier, 6 Li and 7 Li on light targets exhibit similar energy dependence on the imaginary potential. Comparisons are made with 6,7 Li cross sections on light and heavy targets, extracted via previous elastic scattering measurements and also with CDCC calculations. Energy dependent parametrisations are also obtained for total reaction cross sections of 6,7 Li on Si, as well as on any target, at near barrier energies

  12. Novel sodium intercalated (NH4)2V6O16 platelets: High performance cathode materials for lithium-ion battery.

    Science.gov (United States)

    Fei, Hailong; Wu, Xiaomin; Li, Huan; Wei, Mingdeng

    2014-02-01

    A simple and versatile method for preparation of novel sodium intercalated (NH4)2V6O16 is developed via a simple hydrothermal route. It is found that ammonium sodium vanadium bronze displays higher discharge capacity and better rate cyclic stability than ammonium vanadium bronze as lithium-ion battery cathode material because of smaller charge transfer resistance, which would favor superior discharge capacity and rate performance. Crown Copyright © 2013. Published by Elsevier Inc. All rights reserved.

  13. A Unique Failure Mechanism in the Nexus 6P Lithium-Ion Battery

    Directory of Open Access Journals (Sweden)

    Saurabh Saxena

    2018-04-01

    Full Text Available Nexus 6P smartphones have been beset by battery drain issues, which have been causing premature shutdown of the phone even when the charge indicator displays a significant remaining runtime. To investigate the premature battery drain issue, two Nexus 6P smartphones (one new and one used were disassembled and their batteries were evaluated using computerized tomography (CT scan analysis, electrical performance (capacity, resistance, and impedance tests, and cycle life capacity fade tests. The “used” smartphone battery delivered only 20% of the rated capacity when tested in a first capacity cycle and then 15% of the rated capacity in a second cycle. The new smartphone battery exceeded the rated capacity when first taken out of the box, but exhibited an accelerated capacity fade under C/2 rate cycling and decreased to 10% of its initial capacity in just 50 cycles. The CT scan results revealed the presence of contaminant materials inside the used battery, raising questions about the quality of the manufacturing process.

  14. The reaction d(α,γ)6Li at low energies and the primordial nucleosynthesis of 6Li

    International Nuclear Information System (INIS)

    Cecil, F.E.; Yan, J.; Galovich, C.S.

    1996-01-01

    We have searched for the reaction d(α,γ) 6 Li at an α-d center-of-mass energy of 53 keV. An upper limit on the reaction S factor is 2.0x10 -7 MeVb at the 90% confidence level, corresponding to a limit on the synthesis of 6 Li from a standard big bang of 0.9% of the present abundance for a total baryon-to-photon ratio 2.86 10 6 Li-to- 7 Li isotopic abundance ratio immediately after a standard big bang is constrained to be less than 0.85%, considerably less than a recent measurement of this ratio in a metal-poor, Population II halo star. copyright 1996 The American Physical Society

  15. Surprisingly Different Reaction Behavior of Alkali and Alkaline Earth Metal Bis(trimethylsilyl)amides toward Bulky N-(2-Pyridylethyl)-N'-(2,6-diisopropylphenyl)pivalamidine.

    Science.gov (United States)

    Kalden, Diana; Oberheide, Ansgar; Loh, Claas; Görls, Helmar; Krieck, Sven; Westerhausen, Matthias

    2016-07-25

    N-(2,6-Diisopropylphenyl)-N'-(2-pyridylethyl)pivalamidine (Dipp-N=C(tBu)-N(H)-C2 H4 -Py) (1), reacts with metalation reagents of lithium, magnesium, calcium, and strontium to give the corresponding pivalamidinates [(tmeda)Li{Dipp-N=C(tBu)-N-C2 H4 -Py}] (6), [Mg{Dipp-N=C(tBu)-N-C2 H4 -Py}2 ] (3), and heteroleptic [{(Me3 Si)2 N}Ae{Dipp-N=C(tBu)-N-C2 H4 -Py}], with Ae being Ca (2 a) and Sr (2 b). In contrast to this straightforward deprotonation of the amidine units, the reaction of 1 with the bis(trimethylsilyl)amides of sodium or potassium unexpectedly leads to a β-metalation and an immediate deamidation reaction yielding [(thf)2 Na{Dipp-N=C(tBu)-N(H)}] (4 a) or [(thf)2 K{Dipp-N=C(tBu)-N(H)}] (4 b), respectively, as well as 2-vinylpyridine in both cases. The lithium derivative shows a similar reaction behavior to the alkaline earth metal congeners, underlining the diagonal relationship in the periodic table. Protonation of 4 a or the metathesis reaction of 4 b with CaI2 in tetrahydrofuran yields N-(2,6-diisopropylphenyl)pivalamidine (Dipp-N=C(tBu)-NH2 ) (5), or [(thf)4 Ca{Dipp-N=C(tBu)-N(H)}2 ] (7), respectively. The reaction of AN(SiMe3 )2 (A=Na, K) with less bulky formamidine Dipp-N=C(H)-N(H)-C2 H4 -Py (8) leads to deprotonation of the amidine functionality, and [(thf)Na{Dipp-N=C(H)-N-C2 H4 -Py}]2 (9 a) or [(thf)K{Dipp-N=C(H)-N-C2 H4 -Py}]2 (9 b), respectively, are isolated as dinuclear complexes. From these experiments it is obvious, that β-metalation/deamidation of N-(2-pyridylethyl)amidines requires bases with soft metal ions and also steric pressure. The isomeric forms of all compounds are verified by single-crystal X-ray structure analysis and are maintained in solution. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Lithium and Renal Impairment

    DEFF Research Database (Denmark)

    Nielsen, René Ernst; Kessing, Lars Vedel; Nolen, Willem A

    2018-01-01

    INTRODUCTION: Lithium is established as an effective treatment of mania, of depression in bipolar and unipolar disorder, and in maintenance treatment of these disorders. However, due to the necessity of monitoring and concerns about irreversible adverse effects, in particular renal impairment......, after long-term use, lithium might be underutilized. METHODS: This study reviewed 6 large observational studies addressing the risk of impaired renal function associated with lithium treatment and methodological issues impacting interpretation of results. RESULTS: An increased risk of renal impairment...... associated with lithium treatment is suggested. This increased risk may, at least partly, be a result of surveillance bias. Additionally, the earliest studies pointed toward an increased risk of end-stage renal disease associated with lithium treatment, whereas the later and methodologically most sound...

  17. Synthesis of high-purity Li{sub 8}ZrO{sub 6} powder by solid state reaction under hydrogen atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Shin-mura, Kiyoto; Otani, Yu; Ogawa, Seiya [Course of Mechanical Engineering, Graduate School of Engineering, Tokai University, 4-1-1 Kitakaname, Hiratsuka, Kanagawa 259-1292 (Japan); Niwa, Eiki; Hashimoto, Takuya [Department of Physics, College of Humanities and Sciences, Nihon University, 3-8-1 Sakurajousui, Setagaya-ku, Tokyo 156-8550 (Japan); Hoshino, Tsuyoshi [Breeding Functional Materials Development Group, Department of Blanket Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 2-166 Obuchi, Omotedate, Rokkasho-mura, Kamikita-gun, Aomori 039-3212 (Japan); Sasaki, Kazuya, E-mail: k_sasaki@tokai-u.ac.jp [Course of Mechanical Engineering, Graduate School of Engineering, Tokai University, 4-1-1 Kitakaname, Hiratsuka, Kanagawa 259-1292 (Japan); Department of Prime Mover Engineering, School of Engineering, Tokai University, 4-1-1 Kitakaname, Hiratsuka, Kanagawa 259-1292 (Japan)

    2016-11-01

    Highlights: • A fine pure Li{sub 8}ZrO{sub 6} powder was synthesized by using Li{sub 2}CO{sub 3} and ZrO{sub 2} via a solid state reaction. • Influences on the purity of product powder, lattice defect, and crystal orientation were revealed. • The suitable synthesis conditions of the fine and high purity Li{sub 8}ZrO{sub 6} powder were found. • The reaction process of the synthesis of Li{sub 8}ZrO{sub 6} was estimated. - Abstract: Li{sub 8}ZrO{sub 6} contains a large amount of Li and has a significant potential as a tritium breeder. However, few syntheses of fine-grain, high-purity Li{sub 8}ZrO{sub 6} powder have been reported. In this study, a high-purity powder of Li{sub 8}ZrO{sub 6} was synthesized by solid state reaction under hydrogen atmosphere combined with an effective lithium source and a suitable initial Li:Zr molar ratio. Mixed powders of Li{sub 2}CO{sub 3} and ZrO{sub 2} were fired at around 630 °C in H{sub 2} for several hours and several firing cycles. The low firing temperature inhibited the vaporization of Li during the heating, so that excessive amounts of Li were not needed for the synthesis, and the Li:Zr ratio in the starting material was 10:1 (mol:mol). In this synthesis, Li{sub 2}O was generated via the decomposition of Li{sub 2}CO{sub 3} during firing in H{sub 2}, and reacted with ZrO{sub 2} to form Li{sub 6}Zr{sub 2}O{sub 7}, which reacted with itself to form Li{sub 8}ZrO{sub 6}.

  18. Elastic scattering and total reaction cross section for the 6He + 27Al system

    International Nuclear Information System (INIS)

    Benjamim, E.A.; Lepine-Szily, A.; Mendes Junior, D.R.; Lichtenthaeler, R.; Guimaraes, V.; Gomes, P.R.S.; Chamon, L.C.; Hussein, M.S.; Moro, A.M.; Arazi, A.; Padron, I.; Alcantara Nunez, J.; Assuncao, M.; Barioni, A.; Camargo, O.; Denke, R.Z.; Faria, P.N. de; Pires, K.C.C.

    2007-01-01

    The elastic scattering of the radioactive halo nucleus 6 He on 27 Al target was measured at four energies close to the Coulomb barrier using the RIBRAS (Radioactive Ion Beams in Brazil) facility. The Sao Paulo Potential (SPP) was used and its diffuseness and imaginary strength were adjusted to fit the elastic scattering angular distributions. Reaction cross-sections were extracted from the optical model fits. The reduced reaction cross-sections of 6 He on 27 Al are similar to those for stable, weakly bound projectiles as 6,7 Li, 9 Be and larger than stable, tightly bound projectile as 16 O on 27 Al

  19. Study of reaction mechanism for 12C(14N, 6Li) by angular correlation measurement

    International Nuclear Information System (INIS)

    Goldberg, V.Z.; Golovkov, M.S.; Rogatchev, G.V.; Barrov, S.P.; Zurmuhle, R.W.; Liu, Z.; Benton, D.R.; Miao, Y.; Lee, C.; Wimer, N.G.; Murgatroyd, J.T.; Li, X.

    1999-01-01

    An angular correlation for the reaction 12 C ( 14 N, 6 Li) 20 Ne* (α) populating the 8.78 MeV (6 + ) level in 20 Ne is measured at 48 MeV incident 14 N energy. 6 Li is registered for 0-degree geometry in coincidence with α particles from the 20 Ne excited state decay. The results shows that 20% was the upper limit for the contribution of compound nucleus formation. Possible main direct mechanisms of the reaction are discussed [ru

  20. Nuclear reactions of the system 6 Li on 58 Ni near the Coulomb barrier

    International Nuclear Information System (INIS)

    Lizcano, D.; Aguilera, E.F.; Garcia M, H.; Martinez Q, E.

    2004-01-01

    Protons, alpha particles and deuterons coming from the reactions 6 Li + 58 Ni are detected to three different energy around the Coulomb barrier. The possible effects of the weakly bound character of the projectile are studied and the results are compared with previous data for the system 6 Li + 59 Co. (Author)

  1. N,2,3,4-Tetrasubstituted Pyrrolidines through Tandem Lithium Amide Conjugate Addition/Radical Cyclization/Oxygenation Reactions

    Czech Academy of Sciences Publication Activity Database

    Kafka, František; Pohl, Radek; Císařová, I.; Mackman, R.; Bahador, G.; Jahn, Ullrich

    2016-01-01

    Roč. 2016, č. 22 (2016), s. 3862-3871 ISSN 1434-193X R&D Projects: GA ČR GA13-40188S Grant - others:COST(XE) CM1201 Institutional support: RVO:61388963 Keywords : tandem reactions * nitrogen heterocycles * Michael addition * radical reactions * cyclization * enolates Subject RIV: CC - Organic Chemistry Impact factor: 2.834, year: 2016

  2. Reaction channels of 6,7Li+28Si at near-barrier energies

    International Nuclear Information System (INIS)

    Pakou, A; Rusek, K; Nicolis, N G; Alamanos, N; Doukelis, G; Gillibert, A; Kalyva, G; Kokkoris, M; Lagoyannis, A; Musumarra, A; Papachristodoulou, C; Perdikakis, G; Pierroutsakou, D; Pollacco, E C; Spyrou, A; Zarkadas, Ch

    2005-01-01

    The production of α-particles in the reactions 6,7 Li+ 28 Si was studied as a means to disentangle the various reaction channels at near-barrier energies. The competition between compound and direct reactions was determined by using the shape of angular distributions and statistical model calculations. DWBA calculations were also performed to probe the various direct channels. It was found that, approaching barrier, transfer channels are the most dominant for both reactions. For 7 Li+ 28 Si d-transfer is one of the contributing channels without excluding t-transfer, while for 6 Li+ 28 Si, n-transfer and p-transfer have substantial contribution but without excluding d-transfer

  3. Nucleophilic radioiodination of 6-bromocholesterol via non-isotopic exchange reaction in molten state

    International Nuclear Information System (INIS)

    El-Shaboury, G.; Farah, K.; El-Tawoosy, M.

    2001-01-01

    A synthetic method for preparing radioiodinated 6-[ 125 I]iodocholesterol [CL-6- 125 I] for adrenal evaluation is described. The radioiodine atom was incorporated onto the cholesterol molecule via non-isotopic exchange between 6-bromocholesterol [CL-6-Br] and radioiodine as iodide ion [ 125 I - ] in a molten state. The different parameters affecting the yield of exchange were investigated using 125 I (T 1/2 ≅ 60 d) to centralize the different physical and chemical reaction conditions and purification of the final product as pure as 6-[ 125 I]iodocholesterol. The method was suitable to either 131 I (T 1/2 ≅ 8 d) nucleophilic radioiodination which facilitates the scanning of the adrenal for a few days after administration or the use of 124 I (T 1/2 ≅ 4.16 d) nucleophilic radioiodination for PET evaluation of the adrenal. TLC as well as HPLC chromatographic analysis is used to determine the efficiency of the exchange reactions under different chemical reaction conditions and to monitor the stability of the final product as pure as CL-6- 125 I with radiochemical purity of ≅99%. This no-carrier-added method improved the speed of the reaction and affords high radiochemical yield of 90% and suitable specific activity due to the use of CL-6-Br rather than CL-6-I as substrate. Kinetic studies revealed second order iodine-bromine exchange reaction. The activation energy for the exchange reaction in ammonium acetate (m.p. 114 deg C) was calculated to be 4.576 kcal/mole. (author)

  4. Pion inelastic scattering to the first three excited states of lithium-6

    International Nuclear Information System (INIS)

    Kiziah, R.R.

    1984-10-01

    Using the Energetic Pion Channel and Spectrometer system at the Clinton P. Anderson Meson Physics Facility, differential cross sections were measured for π + inelastic scattering to the 3 + , T=0, 2.185-MeV, 0 + , T=1, 3.563-MeV, and 2 + , T=0, 4.25-MeV states of 6 Li at incident pion energies of 120 and 180 MeV and laboratory scattering angles between 15 0 and 47 0 . Excitation functions were measured at a constant momentum transfer of approximately 109 MeV/c for incident pion energies from 100 to 260 MeV. The constant momentum transfer corresponds to the maxima of the angular distributions for π + inelastic scattering to the 3.563-MeV level. Microscopic calculations using the distorted-wave impulse approximation (DWIA) agree well with the measured angular distributions and excitation functions for the 2.185- and 4.25-MeV levels. However, microscopic DWIA calculations do not adequately reproduce the measured angular distributions for the 3.563-MeV level and fail to reproduce the observed anomalous excitation function. The shape of the 3.563-MeV excitation function is similar to that previously observed for π +- inelastic scattering to the 1 + , T=1, 15.11-MeV state of 12 C. The same mechanism may be responsible for the observed excitation functions of both ΔS=ΔT=1 transitions. A possible mechanism is the direct excitation of Δ particle-nucleon hole (Δ-h) components in the final state wave functions. Within the Δ-h model interpretation, the peak of the 3.563-MeV excitation function is reproduced with an estimated probability amplitude for the Δ-h component of the 3.563-MeV state with respect to the ground state of 0.01 less than or equal to β less than or equal to 0.13, a range of values of β consistent with the range estimated for the 15.11-MeV level of 12 C (0.026 less than or equal to β less than or equal to 0.096)

  5. Effects of compatibility of polymer binders with solvate ionic liquid electrolytes on discharge and charge reactions of lithium-sulfur batteries

    Science.gov (United States)

    Nakazawa, Toshitada; Ikoma, Ai; Kido, Ryosuke; Ueno, Kazuhide; Dokko, Kaoru; Watanabe, Masayoshi

    2016-03-01

    Electrochemical reactions in Li-S cells with a solvate ionic liquid (SIL) electrolyte composed of tetraglyme (G4) and Li[TFSA] (TFSA: bis(trifluoromethanesulfonyl)amide) are studied. The sulfur cathode (S cathode) comprises sulfur, carbon powder, and a polymer binder. Poly(ethylene oxide) (PEO) and poly(vinyl alcohol) (PVA-x) with different degrees of saponification (x%) are used as binders to prepare the composite cathodes. For the Li-S cell containing PEO binder, lithium polysulfides (Li2Sm, 2 ≤ m ≤ 8), reaction intermediates of the S cathode, dissolve into the electrolyte, and Li2Sm acts as a redox shuttle in the Li-S cell. In contrast, in the Li-S cell with PVA-x binder, the dissolution of Li2Sm is suppressed, leading to high columbic efficiencies during charge-discharge cycles. The compatibility of the PVA-x binder with the SIL electrolyte changes depending on the degree of saponification. Decreasing the degree of saponification leads to increased electrolyte uptake by the PVA-x binder, increasing the charge and discharge capacities of Li-S cell. The rate capability of Li-S cell is also enhanced by the partial swelling of the PVA-x binder. The enhanced performance of Li-S cell containing PVA-x is attributed to the lowering of resistance of Li+ ion transport in the composite cathode.

  6. Instantaneous formation of SiOx nanocomposite for high capacity lithium ion batteries by enhanced disproportionation reaction during plasma spray physical vapor deposition.

    Science.gov (United States)

    Tashiro, Tohru; Dougakiuchi, Masashi; Kambara, Makoto

    2016-01-01

    Nanocomposite SiO x particles have been produced by a single step plasma spray physical vapor deposition (PS-PVD) through rapid condensation of SiO vapors and the subsequent disproportionation reaction. Core-shell nanoparticles, in which 15 nm crystalline Si is embedded within the amorphous SiO x matrix, form under typical PS-PVD conditions, while 10 nm amorphous particles are formed when processed with an increased degree of non-equilibrium effect. Addition of CH 4 promotes reduction in the oxygen content x of SiO x , and thereby increases the Si volume in a nanocomposite particle. As a result, core-shell nanoparticles with x  = 0.46 as anode exhibit increased initial efficiency and the capacity of lithium ion batteries while maintaining cyclability. Furthermore, it is revealed that the disproportionation reaction of SiO is promoted in nanosized particles attaining increased Si diffusivity by two orders of magnitude compared to that in bulk, which facilitates instantaneous composite nanoparticle formation during PS-PVD.

  7. $^7Be(n,\\alpha)^4He$ reaction and the Cosmological Lithium Problem: measurement of the cross section in a wide energy range at n_TOF (CERN)

    CERN Document Server

    Barbagallo, M.; Cosentino, L.; Maugeri, E.; Heinitz, S.; Mengoni, A.; Dressler, R.; Schumann, D.; Käppeler, F.; Colonna, N.; Finocchiaro, P.; Ayranov, M.; Damone, L.; Kivel, N.; Aberle, O.; Altstadt, S.; Andrzejewski, J.; Audouin, L.; Bacak, M.; Balibrea-Correa, J.; Barros, S.; Bécares, V.; Bečvář, F.; Beinrucker, C.; Berthoumieux, E.; Billowes, J.; Bosnar, D.; Brugger, M.; Caamaño, M.; Calviani, M.; Calviño, F.; Cano-Ott, D.; Cardella, R.; Casanovas, A.; Castelluccio, D. M.; Cerutti, F.; Chen, Y. H.; Chiaveri, E.; Cortés, G.; Cortés-Giraldo, M. A.; Cristallo, S.; Diakaki, M.; Domingo-Pardo, C.; Dupont, E.; Duran, I.; Fernandez-Dominguez, B.; Ferrari, A.; Ferreira, P.; Furman, W.; Ganesan, S.; García-Rios, A.; Gawlik, A.; Glodariu, T.; Göbel, K.; Gonçalves, I. F.; González-Romero, E.; Griesmayer, E.; Guerrero, C.; Gunsing, F.; Harada, H.; Heftrich, T.; Heyse, J.; Jenkins, D. G.; Jericha, E.; Katabuchi, T.; Kavrigin, P.; Kimura, A.; Kokkoris, M.; Krtička, M.; Leal-Cidoncha, E.; Lerendegui, J.; Lederer, C.; Leeb, H.; Lo Meo, S.; Lonsdale, S. J.; Losito, R.; Macina, D.; Marganiec, J.; Martínez, T.; Massimi, C.; Mastinu, P.; Mastromarco, M.; Mazzone, A.; Mendoza, E.; Milazzo, P. M.; Mingrone, F.; Mirea, M.; Montesano, S.; Nolte, R.; Oprea, A.; Pappalardo, A.; Patronis, N.; Pavlik, A.; Perkowski, J.; Piscopo, M.; Plompen, A.; Porras, I.; Praena, J.; Quesada, J.; Rajeev, K.; Rauscher, T.; Reifarth, R.; Riego-Perez, A.; Rout, P.; Rubbia, C.; Ryan, J.; Sabate-Gilarte, M.; Saxena, A.; Schillebeeckx, P.; Schmidt, S.; Sedyshev, P.; Smith, A. G.; Stamatopoulos, A.; Tagliente, G.; Tain, J. L.; Tarifeño-Saldivia, A.; Tassan-Got, L.; Tsinganis, A.; Valenta, S.; Vannini, G.; Variale, V.; Vaz, P.; Ventura, A.; Vlachoudis, V.; Vlastou, R.; Vollaire, J.; Wallner, A.; Warren, S.; Weigand, M.; Weiß, C.; Wolf, C.; Woods, P. J.; Wright, T.; Žugec, P.

    2016-01-01

    The energy-dependent cross section of the 7Be(n,alpha)4He reaction, of interest for the so-called Cosmological Lithium Problem in Big Bang Nucleosynthesis, has been measured for the first time from 10 meV to 10 keV neutron energy. The challenges posed by the short half-life of 7Be and by the low reaction cross section have been overcome at n_TOF thanks to an unprecedented combination of the extremely high luminosity and good resolution of the neutron beam in the new experimental area (EAR2) of the n_TOF facility at CERN, the availability of a sufficient amount of chemically pure 7Be, and a specifically designed experimental setup. Coincidences between the two alpha-particles have been recorded in two Si-7Be-Si arrays placed directly in the neutron beam. The present results are consistent, at thermal neutron energy, with the only previous measurement performed in the 60's at a nuclear reactor. The energy dependence here reported clearly indicates the inadequacy of the cross section estimates currently used in ...

  8. Enrichment of lithium isotope .sup.6./sup.Li by ion exchange resin with specific particle size

    Czech Academy of Sciences Publication Activity Database

    Mikeš, J.; Ďurišová, Jana; Jelínek, L.

    2017-01-01

    Roč. 312, č. 1 (2017), s. 13-18 ISSN 0236-5731 Institutional support: RVO:67985831 Keywords : lithium * isotope separation * elution chromatography * ion exchange chromatography Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Inorganic and nuclear chemistry Impact factor: 1.282, year: 2016

  9. Oxidation reaction of polyether-based material and its suppression in lithium rechargeable battery using 4 V class cathode, LiNi1/3Mn1/3Co1/3O2.

    Science.gov (United States)

    Kobayashi, Takeshi; Kobayashi, Yo; Tabuchi, Masato; Shono, Kumi; Ohno, Yasutaka; Mita, Yuichi; Miyashiro, Hajime

    2013-12-11

    The all solid-state lithium battery with polyether-based solid polymer electrolyte (SPE) is regarded as one of next-generation lithium batteries, and has potential for sufficient safety because of the flammable-electrolyte-free system. It has been believed that polyether-based SPE is oxidized at the polymer/electrode interface with 4 V class cathodes. Therefore, it has been used for electric devices such as organic transistor, and lithium battery under 3 V. We estimated decomposition reaction of polyether used as SPE of all solid-state lithium battery. We first identified the decomposed parts of polyether-based SPE and the conservation of most main chain framework, considering the results of SPE analysis after long cycle operations. The oxidation reaction was found to occur slightly at the ether bond in the main chain with the branched side chain. Moreover, we resolved the issue by introducing a self-sacrificing buffer layer at the interface. The introduction of sodium carboxymethyl cellulose (CMC) to the 4 V class cathode surface led to the suppression of SPE decomposition at the interface as a result of the preformation of a buffer layer from CMC, which was confirmed by the irreversible exothermic reaction during the first charge, using electrochemical calorimetry. The attained 1500 cycle operation is 1 order of magnitude longer than those of previously reported polymer systems, and compatible with those of reported commercial liquid systems. The above results indicate to proceed to an intensive research toward the realization of 4 V class "safe" lithium polymer batteries without flammable liquid electrolyte.

  10. Experimental and theoretical studies of the C{sub 6}H{sub 5} + C{sub 6}H{sub 6} reaction

    Energy Technology Data Exchange (ETDEWEB)

    Park, J.; Burova, S.; Rodgers, A.S.; Lin, M.C.

    1999-11-11

    The absolute rate constants for the C{sub 6}H{sub 5} + C{sub 6}H{sub 6} and C{sub 6}D{sub 6} reactions have been measured by cavity ringdown spectrometry at temperatures between 298 and 495 K at a constant 40 Torr Ar pressure. The new results, which reveal no detectable kinetic isotopic effect, can be represented by the Arrhenius equation, {kappa}{sub 1} = 10{sup (11.91{+-}0.13)} exp[{minus}(2,102 {+-} 106)/T] cm{sup 3}/(mol s). Low-temperature data for the addition/stabilization process, C{sub 6}H{sub 5} + C{sub 6}H{sub 6} {r{underscore}arrow} C{sub 12}H{sub 11}, can be correlated with those obtained in a low-pressure, high-temperature Knudsen cell study for the addition/displacement reaction, C{sub 6}H{sub 5} + C{sub 6}H{sub 6} {r{underscore}arrow} C{sub 12}H{sub 10} + H, by the RRKM theory using the molecular and transition-state parameters computed at the B3LYP/6-311G(d,p) level of theory. Combination of these two sets of data gives {kappa}{sub 1} = 10{sup (11.98{+-}0.03)} exp[{minus}(2168 {+-} 34)/T] cm{sup 3}/(mol s) covering the temperature range 298--1,330 K. The RRKM theory also correlates satisfactorily the forward reaction data with the high-temperature shock-tube result for the reverse H-for-C{sub 6}H{sub 5} substitution process with 2.7 and 4.7 kcal/mol barriers for the entrance (C{sub 6}H{sub 5} + C{sub 6}H{sub 6}) and reverse (H + C{sub 12}H{sub 10}) reactions, respectively. For modeling applications, the authors have calculated the forward reaction rate constants for the formation of the two competing products, H + C{sub 12}H{sub 10} and C{sub 12}H{sub 11}, at several pressures covering 300 K {lt} T {lt} 2,500 K.

  11. Surface treatment of new type aluminum lithium alloy and fatigue crack behaviors of this alloy plate bonded with Ti–6Al–4V alloy strap

    International Nuclear Information System (INIS)

    Sun, Zhen-Qi; Huang, Ming-Hui; Hu, Guo-Huai

    2012-01-01

    Highlights: ► A new generation aluminum lithium alloy which special made for Chinese commercial plane was investigated. ► Pattern of aluminum lithium alloy and Ti alloy were shown after anodization. ► Crack propagation of samples bonded with different wide Ti straps were studied in this paper. -- Abstract: Samples consisting of new aluminum lithium alloy (Al–Li alloy) plate developed by the Aluminum Company of America and Ti–6Al–4V alloy (Ti alloy) plate were investigated. Plate of 400 mm × 140 mm × 2 mm with single edge notch was anodized in phosphoric solution and Ti alloy plate of 200 mm × 20 (40) mm × 2 mm was anodized in alkali solution. Patterns of two alloys were studied at original/anodized condition. And then, aluminum alloy and Ti alloy plates were assembled into a sample with FM 94 film adhesive. Fatigue crack behaviors of the sample were investigated under condition of nominal stress σ = 36 MPa and 54 MPa, stress ratio of 0.1. Testing results show that anodization treatment modifies alloys surface topography. Ti alloy bonding to Al–Li alloy plate effectively retards crack growth than that of Al–Li alloy plate. Fatigue life of sample bonded with Ti alloy strap improves about 62.5% than that of non-strap plate.

  12. Influence of strontium as additive on corrosive-electrochemical behavior of alloy Al +6% lithium in NaCI electrolyte medium

    International Nuclear Information System (INIS)

    Ganiev, I.N.; Norova, M.T.; Nazarov, Kh.M.; Nikitin, V.I.; Karieva, Z.M.

    2005-01-01

    At various voltages, strontium settles down ahead of hydrogen, and the standard electrode potential equals -2,89B. Thus, in relation to aluminum- lithium an alloy Al-Li (6 % lithium) at electrode potential -1,020B, strontium is the anode. Taking into account anodic properties of strontium as additional and its solubility in aluminum-lithium a firm solution is formed, we have selected the following ratio of concentration of an alloying component, 0.01; 0.05; 0.1; 0.5 (mass %). It has perilously been shown, that potential of free corrosion in time, alloys alloyed by strontium, are exposed a little bit faster passivity, than not alloyed. The similar tendency has been observed in all three investigated medium: with the increase in concentration of strontium, the potential of free corrosion is displaced in positive area. Results potentiodynamic researches of alloys in the medium of electrolyte NaCI of various concentration of chlorines -ions the potential of corrosion is displaced in negative area that testifies to decrease of corrosion stability of allays, with growth of aggression of the corrosion medium. It proves to be true accounting speeds of corrosion of alloys from a catholic branch potentiodynamic curves. (author)

  13. Study of the 6Li(p,π+)7Li reaction at 600 MeV

    International Nuclear Information System (INIS)

    Bauer, T.; Beurtey, R.; Boudard, A.; Bruge, G.; Chaumeaux, A.; Couvert, P.; Duhm, H.H.; Garreta, D.; Matoba, M.; Terrein, Y.; Aslanides, E.; Bertini, R.; Brochard, F.; Gorodetzky, Ph.; Hibou, F.; Bimbot, L.; Le Bornec, Y.; Tatischeff, B.; Dillig, M.

    1977-01-01

    The positive pion production through the 6 Li(p,π + ) reaction at 600 MeV has been studied using the high-resolution magnetic spectrometer SPES I. Differential cross sections have been measured from 5 0 to 35 0 sub(lab). The 6 Li(p,π + ) reaction feeds preferentially the 4.63 MeV 7/2 - level of 7 Li. The results of a calculation based on two- and three-nucleon diagrams with π and rho exchange between the projectile and a bound nucleon are also presented. (Auth.)

  14. The Link between Hypersensitivity Syndrome Reaction Development and Human Herpes Virus-6 Reactivation

    Directory of Open Access Journals (Sweden)

    Joshua C. Pritchett

    2012-01-01

    Data Sources and Extraction. Drugs identified as causes of (i idiosyncratic reactions, (ii drug-induced hypersensitivity, drug-induced hepatotoxicity, acute liver failure, and Stevens-Johnson syndrome, and (iii human herpes virus reactivation in PubMed since 1997 have been collected and discussed. Results. Data presented in this paper show that HHV-6 reactivation is associated with more severe organ involvement and a prolonged course of disease. Conclusion. This analysis of HHV-6 reactivation associated with drug-induced severe cutaneous reactions and hepatotoxicity will aid in causality assessment and clinical diagnosis of possible life-threatening events and will provide a basis for further patient characterization and therapy.

  15. Recovery of Lithium from Geothermal Fluid at Lumpur Sidoarjo by Adsorption Method

    Directory of Open Access Journals (Sweden)

    Lukman Noerochim

    2016-05-01

    Full Text Available The recovery of lithium from geothermal fluid at Lumpur Sidoarjo, Indonesia was investigated employing an adsorption method with polymer membrane as container. The lithium concentration in geothermal fluid from Lumpur Sidoarjo used in the present study was about 5 mg/l. Lithium manganese oxide (LMO was selected as a promising adsorbent material due to its non-toxic, topotactical behavior and low cost. In this study, LMO with single Li/Mn mole ratio was prepared, i.e. Li1.6Mn1.6O4. The adsorbent was synthesized by solid state reaction at 500 °C for 5 hrs. A lithium uptake yield from the geothermal fluid of around 6.6 mg/g was obtained.

  16. Interfacial redox reaction-directed synthesis of silver@cerium oxide core-shell nanocomposites as catalysts for rechargeable lithium-air batteries

    Science.gov (United States)

    Liu, Ying; Wang, Man; Cao, Lu-Jie; Yang, Ming-Yang; Ho-Sum Cheng, Samson; Cao, Chen-Wei; Leung, Kwan-Lan; Chung, Chi-Yuen; Lu, Zhou-Guang

    2015-07-01

    A facile oxidation-reduction reaction method has been implemented to prepare pomegranate-like Ag@CeO2 multicore-shell structured nanocomposites. Under Ar atmosphere, redox reaction automatically occurs between AgNO3 and Ce(NO3)3 in an alkaline solution, where Ag+ is reduced to Ag nanopartilces and Ce3+ is simultaneously oxidized to form CeO2, followed by the self-assembly to form the pomegranate-like multicore-shell structured Ag@CeO2 nanocomposites driven by thermodynamic equilibrium. No other organic amines or surfactants are utilized in the whole reaction system and only NaOH instead of organic reducing agent is used to prevent the introduction of a secondary reducing byproduct. The as-obtained pomegranate-like Ag@CeO2 multicore-shell structured nanocomposites have been characterized as electro-catalysts for the air cathode of lithium-air batteries operated in a simulated air environment. Superior electrochemical performance with high discharge capacity of 3415 mAh g-1 at 100 mA g-1, stable cycling and small charge/discharge polarization voltage is achieved, which is much better than that of the CeO2 or simple mixture of CeO2 and Ag. The enhanced properties can be primarily attributed to the synergy effect between the Ag core and the CeO2 shell resulting from the unique pomegranate-like multicore-shell nanostructures possessing plenty of active sites to promote the facile formation and decomposition of Li2O2.

  17. MCNP6 simulation of reactions of interest to FRIB, medical, and space applications

    International Nuclear Information System (INIS)

    Mashnik, Stepan G.

    2015-01-01

    The latest production-version of the Los Alamos Monte Carlo N-Particle transport code MCNP6 has been used to simulate a variety of particle-nucleus and nucleus-nucleus reactions of academic and applied interest to research subjects at the Facility for Rare Isotope Beams (FRIB), medical isotope production, space-radiation shielding, cosmic-ray propagation, and accelerator applications, including several reactions induced by radioactive isotopes, analyzing production of both stable and radioactive residual nuclei. Here, we discuss examples of validation and verification of MCNP6 by comparing with recent neutron spectra measured at the Heavy Ion Medical Accelerator in Chiba, Japan; spectra of light fragments from several reactions measured recently at GANIL, France; INFN Laboratori Nazionali del Sud, Catania, Italy; COSY of the Jülich Research Center, Germany; and cross sections of products from several reactions measured lately at GSI, Darmstadt, Germany; ITEP, Moscow, Russia; and, LANSCE, LANL, Los Alamos, U.S.A. As a rule, MCNP6 provides quite good predictions for most of the reactions we analyzed so far, allowing us to conclude that it can be used as a reliable and useful simulation tool for various applications for FRIB, medical, and space applications involving stable and radioactive isotopes. (author)

  18. Low pressure lithium condensation

    International Nuclear Information System (INIS)

    Wadkins, R.P.; Oh, C.H.

    1985-01-01

    A low pressure experiment to evaluate the laminar film condensation coefficients of lithium was conducted. Some thirty-six different heat transfer tests were made at system pressures ranging from 1.3 to 26 Pa. Boiled lithium was condensed on the inside of a 7.6-cm (ID), 409 stainless-steel pipe. Condensed lithium was allowed to reflux back to the pool boiling region below the condensing section. Fourteen chromel/alumel thermocouples were attached in various regions of the condensing section. The thermocouples were initially calibrated with errors of less than one degree Celsius

  19. Controllable synthesis of a monophase nickel phosphide/carbon (Ni{sub 5}P{sub 4}/C) composite electrode via wet-chemistry and a solid-state reaction for the anode in lithium secondary batteries

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yi; Tu, Jiang-Ping; Xiong, Qin-Qin; Mai, Yong-Jin; Zhang, Jun; Qiao, Yan-Qiang; Wang, Xiu-Li; Gu, Chang-Dong [State Key Laboratory of Silicon Materials and Department of Materials, Science and Engineering, Zhejiang University, Hangzhou, 310027 (China); Xiang, Jia-Yuan [Narada Power Source Co. Ltd., Hangzhou, 311105 (China); Mao, Scott X. [Department of Mechanical Engineering and Materials Science, University of Pittsburgh, Pittsburgh, PA 15261 (United States)

    2012-09-25

    A monophase nickel phosphide/carbon (Ni{sub 5}P{sub 4}/C) composite with a thin carbon shell is controllably synthesized via the two-step strategy of a wet-chemistry reaction and a solid-state reaction. In this fabrication, the further diffusion of phosphorus atoms in the carbon shell during the solid-state reaction can be responsible for a chemical transformation from a binary phase of Ni{sub 5}P{sub 4}-Ni{sub 2}P to monophase Ni{sub 5}P{sub 4}. Galvanostatic charge-discharge measurements indicate that the Ni{sub 5}P{sub 4}/C composite exhibits a superior, high rate capacity and good cycling stability. About 76.6% of the second capacity (644.1 mA h g{sup -1}) can be retained after 50 cycles at a 0.1 C rate. At a high rate of 3 C, the specific capacity of Ni{sub 5}P{sub 4}/C is still as high as 357.1 mA h g{sup -1}. Importantly, the amorphous carbon shell can enhance the conductivity of the composite and suppress the aggregation of the active particles, leading to their structure stability and reversibility during cycling. As is confirmed from X-ray-diffraction analysis, no evident microstructural changes occur upon cycling. These results reveal that highly crystalline Ni{sub 5}P{sub 4}/C is one of the most promising anode materials for lithium-ion batteries. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. Importance of $1n$-stripping process in the $^{6}$Li+$^{159}$Tb reaction

    OpenAIRE

    Pradhan, M. K.; Mukherjee, A.; Roy, Subinit; Basu, P.; Goswami, A.; Kshetri, R.; Palit, R.; Parkar, V. V.; Ray, M.; Sarkar, M. Saha; Santra, S.

    2013-01-01

    The inclusive cross sections of the $\\alpha$-particles produced in the reaction $^{6}$Li+$^{159}$Tb have been measured at energies around the Coulomb barrier. The measured cross sections are found to be orders of magnitude larger than the calculated cross sections of $^{6}$Li breaking into $\\alpha$ and $d$ fragments, thus indicating contributions from other processes. The experimental cross sections of $1n$-stripping and $1n$-pickup processes have been determined from an entirely different me...

  1. Energy dependence of the 3He(3He,π+)6Li reaction

    International Nuclear Information System (INIS)

    Le Bornec, Y.; Hibou, F.; Bimbot, L.; Hennino, T.; Jourdain, J.C.; Reide, F.; Tatischeff, B.; Willis, N.; Aslanides, E.; Bergdolt, G.; Fassnacht, P.; Racca, C.; Boudard, A.; Bruge, G.; Lugol, J.C.

    1983-01-01

    The 3 He( 3 He, π + ) 6 Li reaction has been studied as a function of energy using the 3 He beam at SATURNE. Cross sections for the 6 Li ground state (1 + ) and 2.18 MeV (3 + ) levels have been obtained at 350, 420, 500 and 600 MeV incident energies at angles THETAsub(π)(lab)=15 0 and 40 0 . These results are compared with two theoretical predictions. (orig.)

  2. Lithium Intoxication

    Directory of Open Access Journals (Sweden)

    Sermin Kesebir

    2011-09-01

    Full Text Available Lithium has been commonly used for the treatment of several mood disorders particularly bipolar disorder in the last 60 years. Increased intake and decreased excretion of lithium are the main causes for the development of lithium intoxication. The influence of lithium intoxication on body is evaluated as two different groups; reversible or irreversible. Irreversible damage is usually related with the length of time passed as intoxicated. Acute lithium intoxication could occur when an overdose of lithium is received mistakenly or for the purpose of suicide. Patients may sometimes take an overdose of lithium for self-medication resulting in acute intoxication during chronic, while others could develop chronic lithium intoxication during a steady dose treatment due to a problem in excretion of drug. In such situations, it is crucial to be aware of risk factors, to recognize early clinical symptoms and to conduct a proper medical monitoring. In order to justify or exclude the diagnosis, quantitative evaluation of lithium in blood and toxicologic screening is necessary. Following the monitoring schedules strictly and urgent intervention in case of intoxication would definitely reduce mortality and sequela related with lithium intoxication. In this article, the etiology, frequency, definition, clinical features and treatment approaches to the lithium intoxication have been briefly reviewed.

  3. Nuclear spectroscopy with lithium ions

    International Nuclear Information System (INIS)

    Heiser, C.

    1977-02-01

    A survey of the state of nuclear spectroscopy with lithium ions is given. Proceeding from the physical and nuclear properties the specific topics arising by the acceleration of these ions are discussed. The results obtained from measurements of excitation functions of different lithium reactions, particularly of compound reactions, with several target nuclei are summarized. Besides compound reactions direct reactions are important, especially transfer reactions, elastic and inelastic scattering and exchange reactions. The results on high spin states obtained by in-beam gamma-spectroscopy are discussed in detail. Finally the possibilities are considered for accelerating lithium ions in the cyclotron U-120 and in the tandem generator EGP-10 of the ZfK. (author)

  4. Development of a chemical kinetic measurement apparatus and the determination of the reaction rate constants for lithium-lead/water interaction

    International Nuclear Information System (INIS)

    Biney, P.O.

    1993-04-01

    An experimental set-up for accurate measurement of hydrogen generation rate in Lithium-Lead (Li 17 Pb 83 ) Steam or water interactions has been designed. The most important features of the design include a pneumatic actuated quick opening and closing high temperature all stainless steel valve used to control the reaction time and the placement of most measuring devices below a water line to minimize leakage of the hydrogen collected. A PC based data acquisition and control system provides remote process sequencing, acquisition and control of all major components of the set-up. Initial tests indicate that the first design objective of maintaining leakproof gas collection chamber has been achieved. Initial pressure tests indicated that the pressure drop over a time span of 30 minutes was within the tolerance of the pressure transducer used to measure the pressure (within 0.690 kPa) at a nominal system pressure of 685 kPa. The experimental system hardware, data acquisition and control programs and data analysis program have been completed, tested and are currently functional

  5. Solid NMR study of lithium ions accommodated in various transition metal oxides

    International Nuclear Information System (INIS)

    Kanzaki, Yasushi; Suzuki, Noriko

    2008-01-01

    Solid NMR was used to elucidate the lithium accommodation/extraction reaction in various transition metal oxides. The first study was the lithium ion exchange reaction of titanium antimonic acid (TiSbA). The effect of hydration on the selectivity of lithium ion in the solid phase was examined using 7 Li NMR. The second study was the irreversible ion exchange behavior of HNbO 3 . The selectivity for the lithium ion and the irreversible behavior were examined using 1 H and 7 Li NMR. The third study was the isotope separation between 6 Li and 7 Li in various inorganic ion exchangers. The high isotope separation coefficient was ascribed to the degree of dehydration during the ion exchange reaction. The degree of dehydration was examined by 1 H and 7 Li NMR studies. The last study was determining the mechanism of the lithium accommodation/extraction reaction of λ-MnO 2 in an aqueous solution. The different paths between the accommodation and extraction and the formation of MnO 4- during the accommodation were determined by chemical analysis. The Knight shift in the 7 Li MAS-NMR spectra of Li 0.5 MnO 2 suggested the localization of the electron density on the lithium nuclei. An XPS study also suggested the presence of an electron density on the lithium nuclei. A pH-independent redox couple was assumed to account for the accommodation/extraction reaction of lithium ions, such as Li(I)/Li(0). (author)

  6. Quantitative detection of microscopic lithium distributions with neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Neri, Giulia; Gernhaeuser, Roman; Lichtinger, Josef; Winkler, Sonja; Seiler, Dominik; Bendel, Michael [Technische Universitaet Muenchen, Physik-Department (Germany); Kunze-Liebhaeuser, Julia; Brumbarov, Jassen; Portenkirchner, Engelbert [Institut fuer Physikalische Chemie, Leopold-Franzens-Universitaet Innsbruck (Austria); Renno, Axel; Rugel, Georg [Helmholtz Zentrum Dresden Rossendorf, Helmholtz-Institut Freiberg fuer Ressourcentechnologie (Germany)

    2016-07-01

    The importance of lithium in the modern industrial society is continuously increasing. Spatially resolved detection of tritium particles from {sup 6}Li(n,α){sup 3}H nuclear reactions is used to reconstruct microscopic lithium distributions. Samples are exposed to a flux of cold neutrons. Emitted charged particles are detected with a PSD. Introducing a pinhole aperture between target and detector, the experimental setup works like a ''camera obscura'', allowing to perform spatially resolved measurements. Tritium detection analysis was successfully used to reconstruct the lithium content in self-organized TiO{sub 2-x}-C and Si/TiO{sub 2-x}-C nanotubes electrochemically lithiated, for the first time. Titanium dioxide nanotubes are a candidate for a safe anode material in lithium-ion batteries. Also lithium distributions in geological samples, so called ''pathfinder-minerals'' containing lithium, like lepidolite from a pegmatite, were analyzed. With this development we present a new precision method using nuclear physics for material science.

  7. Transport of 7Be in a lithium loop

    International Nuclear Information System (INIS)

    Katsuta, H.; Anantatmula, R.P.; Bechtold, R.A.; Brehm, W.F.

    1982-07-01

    Beryllium-7 will be produced in the lithium target of the Fusion Materials Irradiation Test (FMIT) facility by the interaction of the deuteron beam with lithium by the two reactions 7 Li(d,2n) 7 Be and 6 Li(d,n) 7 Be. Recent estimates have shown that an equilibrium concentration of 45,000 curies of 7 Be will be present in FMIT lithium. Although this inventory of 7 Be corresponds to only 0.042 wt ppM in FMIT lithium, the radiation fields created can impose special design and maintenance requirements on the facility. A development program has been started at the Hanford Engineering Development Laboratory (HEDL) to investigate the transport of 7 Be in liquid lithium. Results obtained thus far indicated preferential deposition of 7 Be not only in the cold leg but also in the higher temperature region in a nonisothermal lithium system with a temperature gradient similar to that expected in FMIT. The results showed that 7 Be can diffuse into AISI 304 stainless steel (304) at FMIT operating temperatures; the diffusion coefficient of 7 Be in 304 was also calculated

  8. Breakup Reactions and Exclusive Measurements in the 6,7Li+144Sm Systems

    International Nuclear Information System (INIS)

    Heimann, D. Martinez; Pacheco, A. J.; Arazi, A.; Figueira, J. M.; Negri, A. E.; Capurro, O. A.; Carnelli, P.; Fimiani, L.; Grinberg, P.; Marti, G. V.; Testoni, J. E.; Monteiro, D. S.; Niello, J. O. Fernandez; Marta, H. D.

    2009-01-01

    The breakup of the projectile-like nuclei in reactions induced by 30 MeV 6 Li and 7 Li beams on a 144 Sm target have been measured through the coincident detection of the in-plane emitted light particles. The primary ion that undergoes breakup has been identified and the physically meaningful variables that characterize the reaction have been obtained on a purely experimental basis. Distributions have been obtained for both the binary emission angle and for the breakup emission angle in the reference frame of the breakup products.

  9. 16O resonances near 4α threshold through 12C(6Li,d) reaction

    International Nuclear Information System (INIS)

    Rodrigues, M. R. D.; Borello-Lewin, T.; Miyake, H.; Horodynski-Matsushigue, L. B.; Duarte, J. L. M.; Rodrigues, C. L.; Faria, P. Neto de; Cunsolo, A.; Cappuzzello, F.; Foti, A.; Agodi, C.; Cavallaro, M.; Napoli, M. di; Ukita, G. M.

    2014-01-01

    Several narrow alpha resonant 16 O states were detected through the 12 C( 6 Li,d) reaction, in the range of 13.5 to 17.5 MeV of excitation energy. The reaction was measured at a bombarding energy of 25.5 MeV employing the São Paulo Pelletron-Enge-Spectrograph facility and the nuclear emulsion technique. Experimental angular distributions associated with natural parity quasi-bound states around the 4α threshold are presented and compared to DWBA predictions. The upper limit for the resonance widths obtained is near the energy resolution (15 keV)

  10. 16O resonances near 4α threshold through 12C (6Li,d ) reaction

    Science.gov (United States)

    Rodrigues, M. R. D.; Borello-Lewin, T.; Miyake, H.; Horodynski-Matsushigue, L. B.; Duarte, J. L. M.; Rodrigues, C. L.; de Faria, P. Neto; Cunsolo, A.; Cappuzzello, F.; Foti, A.; Agodi, C.; Cavallaro, M.; di Napoli, M.; Ukita, G. M.

    2014-11-01

    Several narrow alpha resonant 16O states were detected through the 12C (6Li,d ) reaction, in the range of 13.5 to 17.5 MeV of excitation energy. The reaction was measured at a bombarding energy of 25.5 MeV employing the São Paulo Pelletron-Enge-Spectrograph facility and the nuclear emulsion technique. Experimental angular distributions associated with natural parity quasi-bound states around the 4α threshold are presented and compared to DWBA predictions. The upper limit for the resonance widths obtained is near the energy resolution (15 keV).

  11. Elastic scattering and total reaction cross section for the 6He +58Ni system

    Science.gov (United States)

    Morcelle, V.; Lichtenthäler, R.; Lépine-Szily, A.; Guimarães, V.; Mendes, D. R., Jr.; Pires, K. C. C.; de Faria, P. N.; Barioni, A.; Gasques, L.; Morais, M. C.; Shorto, J. M. B.; Zamora, J. C.; Scarduelli, V.; Condori, R. Pampa; Leistenschneider, E.

    2014-11-01

    Elastic scattering measurements of 6He + 58Ni system have been performed at the laboratory energy of 21.7 MeV. The 6He secondary beam was produced by a transfer reaction 9Be (7Li , 6He ) and impinged on 58Ni and 197Au targets, using the Radioactive Ion Beam (RIB) facility, RIBRAS, installed in the Pelletron Laboratory of the Institute of Physics of the University of São Paulo, Brazil. The elastic angular distribution was obtained in the angular range from 15° to 80° in the center of mass frame. Optical model calculations have been performed using a hybrid potential to fit the experimental data. The total reaction cross section was derived.

  12. A Finite Strain Model of Stress, Diffusion, Plastic Flow and Electrochemical Reactions in a Lithium-ion Half-cell

    OpenAIRE

    Bower, Allan F.; Guduru, Pradeep R.; Sethuraman, Vijay A.

    2011-01-01

    We formulate the continuum field equations and constitutive equations that govern deformation, stress, and electric current flow in a Li-ion half-cell. The model considers mass transport through the system, deformation and stress in the anode and cathode, electrostatic fields, as well as the electrochemical reactions at the electrode/electrolyte interfaces. It extends existing analyses by accounting for the effects of finite strains and plastic flow in the electrodes, and by exploring in deta...

  13. Neutron emission during lithium deuteride hydration in heavy water

    International Nuclear Information System (INIS)

    Arzhannikov, A.V.; Kezerashvili, G.Ya.; Muratov, V.V.; Sinitskij, S.L.

    1989-01-01

    An experiment on neutron detection during lithium deuteride hydration in heavy water using a system of SNM-17 or SNM-18 gas counters was set up. Signals were simultaneously detected by 6 counters and the data were stored in a computer. At the same time the temperature of the reaction ampule external surface was measured. It was found that the neutron number per 1 gram of lithium deuteride reacted with water in the ampule was equal to several dozens if their initial energy was about 2.5 MeV. 4 refs.; 2 figs

  14. Preparation of Tritium from irradiated lithium compounds (study)

    International Nuclear Information System (INIS)

    1989-01-01

    The aim of the present study is the selection of a certain scheme for release, collection, measurement and analysis of Tritium as produced in Lithium compounds (Li 2 O, LiOH, Li 2 CO 3 LiF and some Lithium alloys) in accordance with the 6 Li(n, α)T reaction. Tritium technology is of vital concern to power reactor programmes as well as to fusion technology. Meanwhile the fields of activity include, tritium generation and mangement in fission and fusion reactors; enviromental studies, release modeling HT/HTO conversion and dose assessments, absorption/ deabsorption, monitoring and plant design; research and development, labeling, compatibility and physical chemical properties

  15. Autoinflammatory Reaction in Dogs Treated for Cancer via G6PD Inhibition

    Directory of Open Access Journals (Sweden)

    Jonathan W. Nyce

    2017-01-01

    Full Text Available Glucose-6-phosphate dehydrogenase (G6PD is an oncoprotein that is overexpressed in cancer cells to provide the NADPH required for their increased anabolism. NADPH, sourced from G6PD fuels nucleotide biosynthesis, maintains redox potential of thioredoxin and glutathione and drives the mevalonate pathway that powers many of the basic mechanisms by which cancer cells escape host control. G6PD is thus a target for cancer treatment being addressed by many groups around the world. We have discovered that systemic inhibition of G6PD by high dose dehydroepiandrosterone (DHEA causes a severe autoinflammatory response in dogs, which does not occur in mice or rats. Since dogs more closely model the human adrenal androgen system than do common laboratory animals, this finding is relevant to the design of G6PD-inhibiting drugs for humans. The autoinflammatory reaction observed closely resembles mevalonate kinase deficiency (MKD, a rare autosomal recessive disease in humans characterized by recurrent febrile attacks, arthralgia, skin rash, and aphthous ulcers of mucocutaneous tissues. In a manner comparable to animal models of MKD, the reconstitution of protein geranylgeranylation blocked the autoinflammatory reaction caused by systemic G6PD inhibition. This autoinflammatory response to systemic G6PD inhibition represents an unexpected result that must be taken into consideration when targeting this oncoprotein.

  16. Helium generation reaction rates for 6Li and 10B in benchmark facilities

    International Nuclear Information System (INIS)

    Farrar, Harry IV; Oliver, B.M.; Lippincott, E.P.

    1980-01-01

    The helium generation rates for 10 B and 6 Li have been measured in two benchmark reactor facilities having neutron spectra similar to those found in a breeder reactor. The irradiations took place in the Coupled Fast Reactivity Measurements Facility (CFRMF) and in the 10% enriched 235 U critical assembly, BIG-10. The helium reaction rates were obtained by precise high-sensitivity gas mass spectrometric analyses of the helium content of numerous small samples. Comparison of these reaction rates with other reaction rates measured in the same facilities, and with rates calculated from published cross sections and from best estimates of the neutron spectral shapes, indicate significant discrepancies in the calculated values. Additional irradiations in other benchmark facilities have been undertaken to better determine the energy ranges where the discrepancies lie

  17. Two-proton pickup studies with the (6Li,8B) reaction

    Energy Technology Data Exchange (ETDEWEB)

    Weisenmiller, R.B.

    1976-12-03

    The (/sup 6/Li,/sup 8/B) reaction has been investigated on targets of /sup 26/Mg, /sup 24/Mg, /sup 16/O, /sup 13/C, /sup 12/C, /sup 11/B, /sup 10/B, and /sup 9/Be at a bombarding energy of 80.0 MeV, and on targets of /sup 16/O, /sup 12/C, /sup 9/Be, /sup 7/Li, and /sup 6/Li at a bombarding energy of 93.3 MeV. Only levels consistent with direct, single-step two-proton pickup reaction mechanisms were observed to be strongly populated. On T/sub z/ = 0 targets, the spectroscopic selectivity of this reaction resembles that of the analogous (p,t) reaction. Additionally, these data demonstrate the dominance of spatially symmetric transfer of the two protons. On T/sub z/ greater than 0 targets the (/sup 6/Li,/sup 8/B) reaction was employed to locate two previously unreported levels (at 7.47 +- 0.05 MeV and 8.86 +- 0.07 MeV) in the T/sub z/ = 2 nuclide /sup 24/Ne and to establish the low-lying 1p-shell states in the T/sub z/ = /sup 3///sub 2/ nuclei /sup 11/Be, /sup 9/Li, and /sup 7/He. However, no evidence was seen for any narrow levels in the T/sub z/ = /sup 3///sub 2/ nuclide /sup 5/H nor for any narrow excited states in /sup 7/He. The angular distributions reported here are rather featureless and decrease monotonically with increasing angle. This behavior can be shown by a semi-classical reaction theory to be a consequence of the reaction kinematics. A semi-classical approach also suggests that the kinematic term in the transition matrix element is only weakly dependent upon the angular momentum transfer (which is consistent with simple Distorted Wave Born Approximation calculations). However, only qualitative agreement was obtained between the observed relative transition yields and semi-classical predictions, using the two-nucleon coefficients of fractional parentage of Cohen and Kurath, probably due to the limitations of the semi-classical reaction theory.

  18. Two-proton pickup studies with the (6Li,8B) reaction

    International Nuclear Information System (INIS)

    Weisenmiller, R.B.

    1976-01-01

    The ( 6 Li, 8 B) reaction has been investigated on targets of 26 Mg, 24 Mg, 16 O, 13 C, 12 C, 11 B, 10 B, and 9 Be at a bombarding energy of 80.0 MeV, and on targets of 16 O, 12 C, 9 Be, 7 Li, and 6 Li at a bombarding energy of 93.3 MeV. Only levels consistent with direct, single-step two-proton pickup reaction mechanisms were observed to be strongly populated. On T/sub z/ = 0 targets, the spectroscopic selectivity of this reaction resembles that of the analogous (p,t) reaction. Additionally, these data demonstrate the dominance of spatially symmetric transfer of the two protons. On T/sub z/ greater than 0 targets the ( 6 Li, 8 B) reaction was employed to locate two previously unreported levels (at 7.47 +- 0.05 MeV and 8.86 +- 0.07 MeV) in the T/sub z/ = 2 nuclide 24 Ne and to establish the low-lying 1p-shell states in the T/sub z/ = 3 / 2 nuclei 11 Be, 9 Li, and 7 He. However, no evidence was seen for any narrow levels in the T/sub z/ = 3 / 2 nuclide 5 H nor for any narrow excited states in 7 He. The angular distributions reported here are rather featureless and decrease monotonically with increasing angle. This behavior can be shown by a semi-classical reaction theory to be a consequence of the reaction kinematics. A semi-classical approach also suggests that the kinematic term in the transition matrix element is only weakly dependent upon the angular momentum transfer (which is consistent with simple Distorted Wave Born Approximation calculations). However, only qualitative agreement was obtained between the observed relative transition yields and semi-classical predictions, using the two-nucleon coefficients of fractional parentage of Cohen and Kurath, probably due to the limitations of the semi-classical reaction theory

  19. Reaction cross section measurements for the production of /sup 6/He(805 ms) and /sup 6/Li(175 ms) with 14. 7 Mev neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Garg, K C; Khurana, C S [Punjabi Univ., Patiala (India). Dept. of Physics

    1979-01-01

    The automatic electronic programmer developed to handle the millisecond isomers has been utilized to measure the reaction cross-sections for the production of /sup 6/He from sup(7,6)Li((n,d)+(n,p))/sup 6/He and /sup 9/Be(n,..cap alpha..)/sup 6/He reactions and /sup 9/Li from /sup 9/Be(n,p)/sup 9/Li reaction. An on-line gated G.M. counter has been used to follow the decay curves of beta-activities of /sup 6/He(805 ms.) and /sup 9/Li(175 ms.) produced in the reactions. Values of measured cross sections are 10.4 +- 1.0 mb., 10.6 +- 1.1 mb. and 40.3 +- 4.0 mb respectively for the above the three reactions.

  20. Lithium Poisoning

    DEFF Research Database (Denmark)

    Baird-Gunning, Jonathan; Lea-Henry, Tom; Hoegberg, Lotte C G

    2017-01-01

    Lithium is a commonly prescribed treatment for bipolar affective disorder. However, treatment is complicated by lithium's narrow therapeutic index and the influence of kidney function, both of which increase the risk of toxicity. Therefore, careful attention to dosing, monitoring, and titration...... is required. The cause of lithium poisoning influences treatment and 3 patterns are described: acute, acute-on-chronic, and chronic. Chronic poisoning is the most common etiology, is usually unintentional, and results from lithium intake exceeding elimination. This is most commonly due to impaired kidney...... function caused by volume depletion from lithium-induced nephrogenic diabetes insipidus or intercurrent illnesses and is also drug-induced. Lithium poisoning can affect multiple organs; however, the primary site of toxicity is the central nervous system and clinical manifestations vary from asymptomatic...

  1. Elastic scattering and charge exchange reaction studies with {sup 6}He, {sup 10,11}Be

    Energy Technology Data Exchange (ETDEWEB)

    Roussel-Chomaz, P; Cortina-Gil, M D; Mittig, W; Casandjian, J M; Chartier, M [Grand Accelerateur National d` Ions Lourds (GANIL), 14 - Caen (France); Alamanos, N; Auger, F; Fekou-Youmbi, V [CEA Centre d` Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. d` Astrophysique, de la Physique des Particules, de la Physique Nucleaire et de l` Instrumentation Associee; Barrette, J [McGill Univ., Montreal, PQ (Canada); Blumenfeld, Y [Paris-11 Univ., 91 - Orsay (France). Inst. de Physique Nucleaire; and others

    1996-12-31

    The elastic scattering and charge exchange reaction of {sup 6}He, {sup 10,11}Be secondary beams on proton and {sup 12}C targets have been measured. The combined use of SISSI and SPEG allowed to obtain very good quality data in terms of energy and angular resolution. Preliminary analyses of the angular distributions using global parameter set for the optical model potentials, as well as more microscopic approaches are presented. (author). 14 refs.

  2. The 208Pb(7Li,6He)209Bi reaction at 52 MeV

    International Nuclear Information System (INIS)

    Zeller, A.F.; Weisser, D.C.; Ophel, T.R.; Hebbard, D.F.

    1979-11-01

    Single proton transfers to low lying levels in 209 Bi from the 208 Pb(7Li, 6 He) reaction at 52 MeV have been measured and spectroscopic factors derived from an EFR-DWBA analysis. Relative spectroscopic factors are in good agreement with light ion results and previous heavy ion work. Absolute spectroscopic factors were generally too large and the peaks of the angular distributions were out of phase with the DWBA calculations by 1 0 - 4 0

  3. Understanding the thermal instability of fluoroethylene carbonate in LiPF6-based electrolytes for lithium ion batteries

    International Nuclear Information System (INIS)

    Kim, Koeun; Park, Inbok; Ha, Se-Young; Kim, Yeonkyoung; Woo, Myung-Heuio; Jeong, Myung-Hwan; Shin, Woo Cheol; Ue, Makoto; Hong, Sung You; Choi, Nam-Soon

    2017-01-01

    Highlights: • The FEC in LiPF 6 -based electrolytes thermally decomposes at elevated temperatures. • Lewis acids in the electrolyte promote de-fluorination of the FEC to form HF. • The HF causes the SEI destruction and severe metal ion dissolution from the cathode. - Abstract: The cycling and storage performances of LiCoO 2 (LCO)-LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM)/pitch-coated silicon alloy-graphite (Si-C) full cells with ethylene carbonate (EC)–based and fluoroethylene carbonate (FEC)–based electrolytes are investigated at elevated temperatures. Excess FEC (used as a co-solvent in LiPF 6 -based electrolytes), which is not completely consumed during the formation of the solid electrolyte interphase (SEI) layer on the electrodes, is prone to defluorination in the presence of Lewis acids such as PF 5 ; this reaction can generate unwanted HF and various acids (H 3 OPF 6 , HPO 2 F 2 , H 2 PO 3 F, H 3 PO 4 ) at elevated temperatures. Our investigation reveals that the HF and acid compounds that are formed by FEC decomposition causes significant dissolution of transition metal ions (from the LCO-NCM cathode) into the electrolyte at elevated temperatures; as a result, the reversible capacity of the full cells reduces because of the deposition of the dissolved metal ions onto the anode. Moreover, we demonstrate possible mechanisms that account for the thermal instability of FEC in LiPF 6 -based electrolytes at elevated temperatures using model experiments.

  4. Chemical effects of (n, γ) nuclear reaction on (Mo6Cl8)Cl4

    International Nuclear Information System (INIS)

    Fucugauchi, L.A.; Millan, S.; Mondragon, A.; Solache-Rios, M.

    1994-01-01

    The chemical effects of 98 Mo(n, γ) 99 Mo reaction on molybdenum(II) chloride [(Mo 6 Cl 8 )Cl 4 ] have been studied. Retention, thermal and radiolytical annealing were determined. It was found that this molybdenum compound has low retention, a negligible tendency to thermal annealing and a virtual insensitivity to hydrolysis. For practical applications in the enrichment of 99 Mo by the Shilard-Chalmers method, molybdenum(II) chloride [(Mo 6 Cl 8 )Cl 4 ] appears to offer good prospects. (author) 14 refs.; 2 figs

  5. Study of the 14N + 159Tb reaction between 6 and 22 MeV/u

    International Nuclear Information System (INIS)

    Balster, G.J.

    1987-01-01

    The main topic of this thesis is the study of the dynamics of asymmetric nucleus-nucleus collisions from low to intermediate energies by concentrating on one specific reaction, 14 N+ 159 Tb. The main experimental techniques involved are inclusive measurements and measurements of coincidences between particles and KX-rays. Additional experiments that were performed to support this study are also discussed. Results from measurements of target KX-ray production cross sections for heavy ion beams at energies above the Coulomb barrier are presented. It is shown that these cross sections can be accurately calculated and hence that the measurement of target KX-rays can serve as a convenient way of normalizing the particle-KX-ray coincidence data. Results from inclusive measurements of 92 MeV 14 N induced reactions on different targets are employed to investigate the reaction systematics at low energies. The systematic study of the 14 N+ 159 Tb reaction between 6 and 22 MeV/u via inclusive measurements and the measurement of particle-KX-ray coincidences is then presented. (Auth.)

  6. Negative ion molecule reactions of WF6: evidence for a pressure dependent branching ratio

    International Nuclear Information System (INIS)

    Viggiano, A.A.; Paulson, J.F.

    1984-01-01

    Rate coefficients have been measured in a selected ion flow tube (SIFT) for reactions of several negative ions with WF 6 . With the exception of SF - 5 , all the reactant ions studied having an electron detachment energy less than 3.36 eV reacted rapidly by charge exchange. SF - 5 transferred a fluoride ion producing WF - 7 . Ions with detachment energies greater than 3.36 eV associated rapidly with WF - 6 . Br - , with a detachment energy of 3.36 eV, reacted with WF 6 both by ion-neutral association and by charge exchange. The branching ratio for these two channels was found to depend on temperature and pressure. All these data indicate that the electron affinity of WF 6 is nearly equal to that of Br

  7. Reaction path of the oxidative coupling of methane over a lithium-doped magnesium oxide catalyst : Factors affecting the Rate of Total Oxidation of Ethane and Ethylene

    NARCIS (Netherlands)

    Roos, J.A.; Korf, S.J.; Veehof, R.H.J.; van Ommen, J.G.; Ross, J.R.H.

    1989-01-01

    Experiments using gas mixtures of O2, C2H6 or C2H4 and CH4 or He have been carried out with a Li/MgO catalyst using a well-mixed reaction system which show that the total oxidation products, CO and CO2, are formed predominantly from ethylene, formed in the oxidative coupling of methane. It is

  8. Carbon-Encapsulated Co3O4@CoO@Co Nanocomposites for Multifunctional Applications in Enhanced Long-life Lithium Storage, Supercapacitor and Oxygen Evolution Reaction

    International Nuclear Information System (INIS)

    Xu, Dongyang; Mu, Congpu; Xiang, Jianyong; Wen, Fusheng; Su, Can; Hao, Chunxue; Hu, Wentao; Tang, Yongfu; Liu, Zhongyuan

    2016-01-01

    Porous nanostructure composites materials had attracted widely attention due to their potential application in energy storage (Lithium ion batteries (LIBs) and supercapacitor) and electrocatalyst of oxygen evolution reaction (OER). Co 3 O 4 @CoO@Co@C nanocomposites had been successfully synthesized using glucose as carbon source and cobalt nitrate as metalprecurs or of Co 3 O 4 @CoO@Co@C, which has excellent electrochemical performance for LIBs, supercapacitor and OER. Three kinds of morphology samples marked by Co 3 O 4 @CoO@Co@C-2/1, Co 3 O 4 @CoO@Co@C-1/1 and Co 3 O 4 @CoO@Co@C-1/2 are synthesized due to different atomic ratio of cobalt/carbon in precursors. Electrochemical and catalytic performance of Co 3 O 4 @CoO@Co@C-2/1 nanocomposites is more excellent than Co 3 O 4 @CoO@Co@C-1/1 and Co 3 O 4 @CoO@Co@C-1/2. Co 3 O 4 @CoO@Co@C-2/1 shows that discharge capacity can maintain 450 mA h g −1 and coulombic efficiency is nearly 100% during 500 cycles for LIBs. It indicates the excellent cycling stability of Co 3 O 4 @CoO@Co@C-2/1 as electrode for supercapacitor that about 78.3% of initial specific capacitance can be retained after 10000 cycles at current density of 2 A g −1 . Co 3 O 4 @CoO@Co@C-2/1 as catalyst of OER shows excellent electrochemical durability over 15 hours continuous experiment.

  9. A Novel High-Power Battery-Pseudocapacitor Hybrid Based on Fast Lithium Reactions in Silicon Anode and Titanium Dioxide Cathode Coated on Vertically Aligned Carbon Nanofibers

    International Nuclear Information System (INIS)

    Klankowski, Steven A.; Pandey, Gaind P.; Malek, Gary A.; Wu, Judy; Rojeski, Ronald A.; Li, Jun

    2015-01-01

    Highlights: • A unique battery-supercapacitor hybrid has been demonstrated. • Both Si anode and TiO_2 cathode are fabricated in the form of nanocolumnar shells coated on VACNFs. • Hybrid cells achieve stable charge-discharge cycles in the supercapacitor power regime. - Abstract: An electrochemical cell representing a battery-supercapacitor hybrid is demonstrated with a Si anode and a TiO_2 cathode based on Lithium chemistry. Both materials are fabricated as coaxial shells with an oblique nanocolumnar structure anchored on vertical aligned carbon nanofiber arrays. The Li"+ ion transport and electrical connection is greatly enhanced with such nanoporous core-shell architectures, leading to optimal Li storage properties. The full theoretical capacity of the shell materials has been obtained at normal C-rates (C/1 to C/2) for Si (∼3,000 to 3500 mA h g"−"1) and TiO_2 (∼170 mA h g"−"1) half-cells, respectively, with excellent cycling stability. More importantly, much higher rates (up to 4.7C_S_i for Si and 76C_T_i_O_2 for TiO_2) can be applied at relatively small capacity loss, approaching the properties of supercapacitors. The charge-discharge profiles show battery-supercapacitor hybrid features, which are attributed to the short Li"+ diffusion path across the solid materials and the large pseudocapacitive contribution from fast surface reactions. A full cell containing similar volume of Si and TiO_2 shows a high specific energy (103 W h kg"−"1) at low current rates, comparable to a decent battery, and a remarkable specific power (56,000 W kg"−"1) at high current rates, matching the state-of-the-art supercapacitors.

  10. Interaction of 2,4,6-trichlorophenol with high carbon iron filings: Reaction and sorption mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, Alok [Environmental Engineering and Management Programme, Department of Civil Engineering, Indian Institute of Technology Kanpur, Kanpur 208016 (India); Bose, Purnendu [Environmental Engineering and Management Programme, Department of Civil Engineering, Indian Institute of Technology Kanpur, Kanpur 208016 (India)], E-mail: pbose@iitk.ac.in

    2009-05-15

    Reductive dehalogenation of 2,4,6-trichlorophenol (2,4,6-TCP) by two types of high carbon iron filings (HCIF), HCIF-1 and HCIF-2 was studied in batch reactors. While the iron, copper, manganese and carbon content of the two types of HCIF was similar, the specific surface area of HCIF-1 and HCIF-2 were 1.944 and 3.418 m{sup 2} g{sup -1}, respectively. During interaction with HCIF-1, 2,4,6-TCP adsorbed on HCIF-1 surface resulting in rapid reduction of aqueous phase 2,4,6-TCP concentration. However, reductive dehalogenation of 2,4,6-TCP was negligible. During interaction between 2,4,6-TCP and HCIF-2, both 2,4,6-TCP adsorption on HCIF-2, and 2,4,6,-TCP dechlorination was observed. 2,4,6-TCP partitioning between solid and aqueous phase could be described by a Freundlich isotherm, while 2,4,6-TCP dechlorination could be described by an appropriate rate expression. A mathematical model was developed for describing the overall interaction of 2,4,6-TCP with HCIF-2, incorporating simultaneous adsorption/desorption and dechlorination reactions of 2,4,6-TCP with the HCIF surface. 2,4-Dichlorophenol (2,4-DCP), 2-chlorophenol (2-CP) and minor amounts of 4-chlorophenol (4-CP) evolved as 2,4,6-TCP dechlorination by-products. The evolved 2,4-DCP partitioned strongly to the HCIF surface. 4-CP and 2-CP accumulated in the aqueous phase. No transformation of 2-CP or 4-CP to phenol was observed.

  11. Kinetics on the reaction of 6-chloroquinoline and p-substituted benzoylchlorides under high pressures

    International Nuclear Information System (INIS)

    Kim, Eung Ryul; Lim, Jong Wan; Kim, Se Kyong; Ko, Young Shin

    2002-01-01

    The reactions rates of substituted 6-chloroquinoline, with p-substituted benzoyichlorides (p-CH 3 , p-H, p-NO 2 ) have been measured by conductometry in acetonitrile, and the rate constants are determined at various temperatures (10,15,20,25 .deg. C) and pressures (1, 200, 500, 1000 bar). From the values of rate constants, the activation parameters (Ea, ΔV ≠ , ΔH ≠ , ΔS ≠ , and ΔG ≠ ) and the pressure dependence of Hammett ρ values were determined. The rate constants increased with increasing temperatures and pressures, and are further increased to introduction to the electron donor substituents in substrate (p-NO 2 ) with 6-chloroquinoline. When, the activation volume and the activation entropy are all negative. And the Hammett ρ values are positive for the substrate over the pressure and temperature range studied. The results of kinetic studies for pressure and substituent show that thease reactions proceed in typical S N 2 reaction mechanism and 'associative S N 2' in bond formation favored with increasing pressures

  12. Lattice vibrations of materials for lithium rechargeable batteries II. Lithium extraction-insertion in spinel structures

    International Nuclear Information System (INIS)

    Julien, C.M.; Camacho-Lopez, M.A.

    2004-01-01

    Lithiated spinel manganese oxides with various amounts of lithium have been prepared through solid-state reaction and electrochemical intercalation and deintercalation. Local structure of the samples are studied using Raman scattering and Fourier transform infrared spectroscopy. We report vibrational spectra of lithiated manganese oxides Li x Mn 2 O 4 as a function of lithium concentration in the range 0.1≤x≤2.0. Raman and Fourier transform infrared (FTIR) spectral results indicated multiple-phase reactions when the lithium content is modified in the spinel lattice. Lattice dynamics of lithiated spinel manganese oxides have been interpreted using either a classical factor-group analysis or a local environment model. The structural modifications have been studied on the basis of vibrations of LiO 4 tetrahedral and MnO 6 octahedral units when Li/Mn≤0.5, and LiO 4 , LiO 6 , and MnO 6 structural units when Li/Mn>0.5

  13. Investigation of α-cluster states in 13C via the (6Li,d) reaction

    CERN Document Server

    Rodrigues, M R D; Horodynski-Matsushigue, L B; Cunsolo, A; Cappuzzello, F; Duarte, J L M; Rodrigues, C L; Ukita, G M; Souza, M A; Miyake, H

    2010-01-01

    The 9Be(6Li,d)13C reaction was used to investigate possible α-cluster states in 13C. The reaction was measured at 25.5 MeV incident energy, employing the São Paulo Pelletron-Enge-Spectrograph facility and the nuclear emulsion detection technique. Ten out of sixteen known levels of 13C, up to 11 MeV of excitation, were observed and, due to the much improved energy resolution of 50 keV, at least three doublets could be resolved. This work presents a preliminary analysis of five of the most intensely populated states, also in comparison with the results of former transfer studies.

  14. Probing the 8He ground state via the 8He(p,t)6He reaction

    International Nuclear Information System (INIS)

    Keeley, N.; Skaza, F.; Lapoux, V.; Alamanos, N.; Auger, F.; Beaumel, D.; Becheva, E.; Blumenfeld, Y.; Delaunay, F.; Drouart, A.; Gillibert, A.; Giot, L.; Kemper, K.W.; Nalpas, L.; Pakou, A.; Pollacco, E.C.; Raabe, R.; Roussel-Chomaz, P.; Rusek, K.; Scarpaci, J.-A.; Sida, J.-L.; Stepantsov, S.; Wolski, R.

    2007-01-01

    The weakly-bound 8 He nucleus exhibits a neutron halo or thick neutron skin and is generally considered to have an α+4n structure in its ground state, with the four valence neutrons each occupying 1p 3/2 states outside the α core. The 8 He(p,t) 6 He reaction is a sensitive probe of the ground state structure of 8 He, and we present a consistent analysis of new and existing data for this reaction at incident energies of 15.7 and 61.3A MeV, respectively. Our results are incompatible with the usual assumption of a pure (1p 3/2 ) 4 structure and suggest that other configurations such as (1p 3/2 ) 2 (1p 1/2 ) 2 may be present with significant probability in the ground state wave function of 8 He

  15. Lithium Batteries

    Science.gov (United States)

    National Laboratory, Materials Science and Technology Division Lithium Batteries Resources with Additional thin-film lithium batteries for a variety of technological applications. These batteries have high essentially any size and shape. Recently, Teledyne licensed this technology from ORNL to make batteries for

  16. Predictors of excellent response to lithium

    DEFF Research Database (Denmark)

    Kessing, Lars Vedel; Hellmund, Gunnar; Andersen, Per Kragh

    2011-01-01

    The aim of this study was to identify sociodemographic and clinical predictors of excellent response, that is, 'cure' of future affective episodes, to lithium in monotherapy. We used nationwide registers to identify all patients with a diagnosis of bipolar disorder in psychiatric hospital settings...... who were prescribed lithium from 1995 to 2006 in Denmark (N=3762). Excellent lithium responders were defined as patients who after a stabilization lithium start-up period of 6 months, continued lithium in monotherapy without getting hospitalized. The rate of excellent response to lithium...... with somatic comorbidity had increased rates of non-response to lithium compared with patients without somatic comorbidity (HR=1.23, 95% CI: 1.00-1.52).It is concluded that the prevalence of excellent response to lithium monotherapy is low and such patients are characterized by few earlier psychiatric...

  17. About the safety of lithium batteries with carbon anode; De la securite des accumulateurs au lithium a anode de carbone

    Energy Technology Data Exchange (ETDEWEB)

    Biensan, Ph.; Le Nay, F. [SAFT, Direction de la Recherche, 91 - Marcoussis (France); Simon, B. [Alcatel Alsthom Recherche, 91 - Marcoussis (France); Bodet, J.M. [SAFT, Advanced and Industrial Battery Group, 86 - Poitiers (France)

    1996-12-31

    The replacement of lithium metal from the negative electrode of lithium batteries by a material allowing the reversible insertion of lithium ions is an undeniable commercial success. Carbon electrodes, generally called Li{sub x}C{sub 6}, are the most common type and allow to increase the service life of the battery, its charging fastness and its safety. The safety of such batteries is well known in normal conditions of use, but it has to be known also in any abusive condition of use, whatever is the charging state. The mastery of the phenomena that can occur requires a good knowledge of the kinetics of the exothermal chemical reactions involved. (J.S.) 8 refs.

  18. About the safety of lithium batteries with carbon anode; De la securite des accumulateurs au lithium a anode de carbone

    Energy Technology Data Exchange (ETDEWEB)

    Biensan, Ph; Le Nay, F [SAFT, Direction de la Recherche, 91 - Marcoussis (France); Simon, B [Alcatel Alsthom Recherche, 91 - Marcoussis (France); Bodet, J M [SAFT, Advanced and Industrial Battery Group, 86 - Poitiers (France)

    1997-12-31

    The replacement of lithium metal from the negative electrode of lithium batteries by a material allowing the reversible insertion of lithium ions is an undeniable commercial success. Carbon electrodes, generally called Li{sub x}C{sub 6}, are the most common type and allow to increase the service life of the battery, its charging fastness and its safety. The safety of such batteries is well known in normal conditions of use, but it has to be known also in any abusive condition of use, whatever is the charging state. The mastery of the phenomena that can occur requires a good knowledge of the kinetics of the exothermal chemical reactions involved. (J.S.) 8 refs.

  19. Reaction

    African Journals Online (AJOL)

    abp

    19 oct. 2017 ... Reaction to Mohamed Said Nakhli et al. concerning the article: "When the axillary block remains the only alternative in a 5 year old child". .... Bertini L1, Savoia G, De Nicola A, Ivani G, Gravino E, Albani A et al ... 2010;7(2):101-.

  20. Scalable and template-free synthesis of nanostructured Na{sub 1.08}V{sub 6}O{sub 15} as high-performance cathode material for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Shili, E-mail: slzheng@ipe.ac.cn [National Engineering Laboratory for Hydrometallurgical Cleaner Production Technology, Key Laboratory of Green Process and Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing (China); Wang, Xinran; Yan, Hong [National Engineering Laboratory for Hydrometallurgical Cleaner Production Technology, Key Laboratory of Green Process and Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing (China); University of Chinese Academy of Sciences, No. 19A Yuquan Road, Beijing (China); Du, Hao; Zhang, Yi [National Engineering Laboratory for Hydrometallurgical Cleaner Production Technology, Key Laboratory of Green Process and Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing (China)

    2016-09-15

    Highlights: • Nanostructured Na{sub 1.08}V{sub 6}O{sub 15} was synthesized through additive-free sol-gel process. • Prepared Na{sub 1.08}V{sub 6}O{sub 15} demonstrated high capacity and sufficient cycling stability. • The reaction temperature was optimized to allow scalable Na{sub 1.08}V{sub 6}O{sub 15} fabrication. - Abstract: Developing high-capacity cathode material with feasibility and scalability is still challenging for lithium-ion batteries (LIBs). In this study, a high-capacity ternary sodium vanadate compound, nanostructured NaV{sub 6}O{sub 15}, was template-free synthesized through sol-gel process with high producing efficiency. The as-prepared sample was systematically post-treated at different temperature and the post-annealing temperature was found to determine the cycling stability and capacity of NaV{sub 6}O{sub 15}. The well-crystallized one exhibited good electrochemical performance with a high specific capacity of 302 mAh g{sup −1} when cycled at current density of 0.03 mA g{sup −1}. Its relatively long-term cycling stability was characterized by the cell performance under the current density of 1 A g{sup −1}, delivering a reversible capacity of 118 mAh g{sup −1} after 300 cycles with 79% capacity retention and nearly 100% coulombic efficiency: all demonstrating its significant promise of proposed strategy for large-scale synthesis of NaV{sub 6}O{sub 15} as cathode with high-capacity and high energy density for LIBs.

  1. Study of the 6Li + p → 3He + 4He reaction in inverse kinematics

    International Nuclear Information System (INIS)

    Betsou, C.; Pakou, A.; Aslanoglou, X.; Nicolis, N.G.; Sgouros, O.; Soukeras, V.; Cappuzzello, F.; Acosta, L.; Agodi, C.; Carbone, D.; Cavallaro, M.; Di Pietro, A.; Fernandez-Garcia, J.P.; Figuera, P.; Fisichella, M.; Foti, A.; Keeley, N.; Marquinez-Duran, G.; Martel, I.; Mazzocco, M.; Strano, E.; Torresi, D.; Pierroutsakou, D.; Rusek, K.; Stiliaris, E.

    2015-01-01

    Angular distribution measurements were performed for the 6 Li + p → 3 He + 4 He reaction in inverse kinematics at incident energies of 2.7, 3.3, 4.2 and 4.8 MeV/u. The detection of both recoils ( 3 He and 4 He) over the laboratory angle range θ lab = 16 circle to 34 circle allowed the determination of the angular distribution over a wide angular range in the center-of-mass frame (θ c.m. ∝ 40 circle to 140 circle ). The results clarify inconsistencies between existing data sets and are consistent with compound nucleus model calculations. (orig.)

  2. Accelerating rate calorimetry studies of the reactions between ionic liquids and charged lithium ion battery electrode materials

    International Nuclear Information System (INIS)

    Wang, Yadong; Zaghib, K.; Guerfi, A.; Bazito, Fernanda F.C.; Torresi, Roberto M.; Dahn, J.R.

    2007-01-01

    Using accelerating rate calorimetry (ARC), the reactivity between six ionic liquids (with and without added LiPF 6 ) and charged electrode materials is compared to the reactivity of standard carbonate-based solvents and electrolytes with the same electrode materials. The charged electrode materials used were Li 1 Si, Li 7 Ti 4 O 12 and Li 0.45 CoO 2 . The experiments showed that not all ionic liquids are safer than conventional electrolytes/solvents. Of the six ionic liquids tested, 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide (EMI-FSI) shows the worst safety properties, and is much worse than conventional electrolyte. 1-Ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (EMI-TFSI) and 1-propyl-1-methylpyrrolidinium bis(fluorosulfonyl)imide (Py13-FSI) show similar reactivity to carbonate-based electrolyte. The three ionic liquids 1-butyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide (BMMI-TFSI), 1-butyl-1-methylpiperidinium bis(trifluoromethanesulfonyl)imide (Pp14-TFSI) and N-trimethyl-N-butylammonium bis(trifluoromethanesulfonyl)imide (TMBA-TFSI) show similar reactivity and are much safer than the conventional carbonate-based electrolyte. A comparison of the reactivity of ionic liquids with common anions and cations shows that ionic liquids with TFSI - are safer than those with FSI - , and liquids with EMI + are worse than those with BMMI + , Py13 + , Pp14 + and TMBA +

  3. Quasi-bound alpha resonant states populated by the 12C(6Li, d) reaction

    International Nuclear Information System (INIS)

    Rodrigues, M.R.D.; Borello-Lewin, T.; Miyake, H.; Horodynski-Matsushigue, L.B.; Duarte, J.L.M.; Rodrigues, C.L.; Souza, M.A.; Cunsolo, A.; Cappuzzello, F.; Foti, A.; Agodi, C.; Cavallaro, M.; Ukita, G.M.

    2012-01-01

    Full text: The alpha cluster phenomenon in the light nuclei structure has been the subject of a long time investigation since the proposal of the Ikeda diagrams [1]. The main purpose of the research program in progress is the investigation of this phenomenon in (xα) and (xα+n) nuclei through the ( 6 Li, d) alpha transfer reaction [2-4]. Alpha resonant states around the (4α) threshold in the nucleus 16 O are the focus of the present contribution. In fact, the importance of these resonances at the elements production in stars is recognized, as primarily pointed out by Hoyle in 12 C [6]. The existence of a rotational band with the α + 12 C (Hoyle) cluster state structure was recently demonstrated by Ohkubo and Hirabayashi [6]. In order to explore this region of interest, measurements of the 12 C( 6 Li, d) 16 O reaction up to 17 MeV of excitation at an incident energy of 25.5 MeV, have been performed employing the Sao Paulo Pelletron-Enge Split-Pole facility and the nuclear emulsion detection technique (plates Fuji G6B, 50 μm thick). Spectra associated with six scattering angles, from 5 deg to 29 deg in the laboratory frame, each one 50 cm along the focal surface, were measured. Several narrow resonances with a quasi-bound behavior embedded in the continuum were detected and the resolution of 25 keV allowed for the separation of doublets not resolved before [7,8]. The absolute cross sections and the respective deuteron angular distributions were determined and the analysis is in progress. [1] K. Ikeda et al., Prog. Theor. Phys. Suppl. E 68, 464 (1968); H. Horiuchi, K. Ikeda, and Y. Suzuki, ibid. 44, 225 (1978). [2] M.R.D.Rodrigues et al., in12th International Conference on Nuclear Reaction Mechanism, Varenna, Italy, edited by F. Cerutti and A. Ferrari , CERN Proceedings, 2010-2, pp. 331- 335. [3] T. Borello-Lewin et al., Proceedings of SOTANCP2, Brussels, Belgium 2010, edited by P. Descouvemount et al., Int. J. Mod. Mod. Phys E 20, 1018-1021 (2011). [4] T. Borello

  4. NMR study of thermal decomposition of lithium tetrahydroaluminate

    International Nuclear Information System (INIS)

    Tarasov, V.P.; Bakum, S.I.; Kuznetsova, S.F.

    1997-01-01

    Pyrolysis of lithium aluminotetrahydrides and deuterides, LiAlH 4 and LiAlD 4 , was studied by 1 H, 7 Li, 27 Al NMR in 20-700 deg C range. 20-30 time constriction of resonance lines of studied nuclei at 170 deg C testifies to melting of the compounds. It is shown that at LiAlD 4 melting point the first stage of pyrolysis is described by two parallel reactions: LiAlD 4 -> LiD + Al + D 2 , LiAlD 4 + LiD -> Li 3 AlD 6 , which proceed with different rates. It was revealed that reactions of lithium hydride (deuteride) with metallic aluminium at temperatures above 400 deg C resulted to formation of intermetallic compounds of LiAl and LiAl 3 composition. LiAl is characterized by higher thermal stability, than LiAl 3 . 20 refs., 6 figs., 2 tabs

  5. ^{7}Be(n,α)^{4}He Reaction and the Cosmological Lithium Problem: Measurement of the Cross Section in a Wide Energy Range at n_TOF at CERN.

    Science.gov (United States)

    Barbagallo, M; Musumarra, A; Cosentino, L; Maugeri, E; Heinitz, S; Mengoni, A; Dressler, R; Schumann, D; Käppeler, F; Colonna, N; Finocchiaro, P; Ayranov, M; Damone, L; Kivel, N; Aberle, O; Altstadt, S; Andrzejewski, J; Audouin, L; Bacak, M; Balibrea-Correa, J; Barros, S; Bécares, V; Bečvář, F; Beinrucker, C; Berthoumieux, E; Billowes, J; Bosnar, D; Brugger, M; Caamaño, M; Calviani, M; Calviño, F; Cano-Ott, D; Cardella, R; Casanovas, A; Castelluccio, D M; Cerutti, F; Chen, Y H; Chiaveri, E; Cortés, G; Cortés-Giraldo, M A; Cristallo, S; Diakaki, M; Domingo-Pardo, C; Dupont, E; Duran, I; Fernandez-Dominguez, B; Ferrari, A; Ferreira, P; Furman, W; Ganesan, S; García-Rios, A; Gawlik, A; Glodariu, T; Göbel, K; Gonçalves, I F; González-Romero, E; Griesmayer, E; Guerrero, C; Gunsing, F; Harada, H; Heftrich, T; Heyse, J; Jenkins, D G; Jericha, E; Katabuchi, T; Kavrigin, P; Kimura, A; Kokkoris, M; Krtička, M; Leal-Cidoncha, E; Lerendegui, J; Lederer, C; Leeb, H; Lo Meo, S; Lonsdale, S J; Losito, R; Macina, D; Marganiec, J; Martínez, T; Massimi, C; Mastinu, P; Mastromarco, M; Mazzone, A; Mendoza, E; Milazzo, P M; Mingrone, F; Mirea, M; Montesano, S; Nolte, R; Oprea, A; Pappalardo, A; Patronis, N; Pavlik, A; Perkowski, J; Piscopo, M; Plompen, A; Porras, I; Praena, J; Quesada, J; Rajeev, K; Rauscher, T; Reifarth, R; Riego-Perez, A; Rout, P; Rubbia, C; Ryan, J; Sabate-Gilarte, M; Saxena, A; Schillebeeckx, P; Schmidt, S; Sedyshev, P; Smith, A G; Stamatopoulos, A; Tagliente, G; Tain, J L; Tarifeño-Saldivia, A; Tassan-Got, L; Tsinganis, A; Valenta, S; Vannini, G; Variale, V; Vaz, P; Ventura, A; Vlachoudis, V; Vlastou, R; Vollaire, J; Wallner, A; Warren, S; Weigand, M; Weiß, C; Wolf, C; Woods, P J; Wright, T; Žugec, P

    2016-10-07

    The energy-dependent cross section of the ^{7}Be(n,α)^{4}He reaction, of interest for the so-called cosmological lithium problem in big bang nucleosynthesis, has been measured for the first time from 10 meV to 10 keV neutron energy. The challenges posed by the short half-life of ^{7}Be and by the low reaction cross section have been overcome at n_TOF thanks to an unprecedented combination of the extremely high luminosity and good resolution of the neutron beam in the new experimental area (EAR2) of the n_TOF facility at CERN, the availability of a sufficient amount of chemically pure ^{7}Be, and a specifically designed experimental setup. Coincidences between the two alpha particles have been recorded in two Si-^{7}Be-Si arrays placed directly in the neutron beam. The present results are consistent, at thermal neutron energy, with the only previous measurement performed in the 1960s at a nuclear reactor. The energy dependence reported here clearly indicates the inadequacy of the cross section estimates currently used in BBN calculations. Although new measurements at higher neutron energy may still be needed, the n_TOF results hint at a minor role of this reaction in BBN, leaving the long-standing cosmological lithium problem unsolved.

  6. Alpha cluster states in light nuclei populated through the (6Li,d) reaction

    International Nuclear Information System (INIS)

    Borello-Lewin, Thereza; Rodrigues, M.R.D.; Horodynski-Matsushigue, L.B.; Duarte, J.L.M.; Rodrigues, C.L.; Souza, M.A.; Cunsolo, A.; Cappuzzello, F.; Ukita, Gilberto Mitsuo

    2011-01-01

    Full text: The alpha cluster correlation is an important concept in the nuclear physics of light nuclei. The main purpose of the research program in progress is the investigation of the alpha clustering phenomenon in (xα) and(xα+ν) nuclei through the ( 6 Li,d) alpha transfer reaction. In fact, there is scarce experimental information on the subject, in particular associated with resonant states predicted near (xα) and (xα+ν) thresholds. Measurements of the 12 , 13 C( 6 Li,d) 16 , 17 O reactions, at an incident energy of 25.5 MeV, have been performed employing the Sao Paulo Pelletron-Enge Split-Pole facility and the nuclear emulsion detection technique. The work is under way and an experimental energy resolution of 30 keV was obtained. Near the (4α) breakup threshold in 16 O, three narrow alpha resonances, not previously measured, were detected, revealing important α + 12 C(G.S.) components. One of these resonances corresponds to the known 0 + state at 15.1 MeV[5] of excitation that has probably, according to Funaki et al., the gas like configuration of the 4α condensate state, with a very dilute density and a large component of α + 12 C(Hoyle) configuration. As was already mentioned, our experimental information points to the necessity of including the α + 12 C(G.S.) component in the wave function. (author)

  7. Effects of Propylene Carbonate Content in CsPF6-Containing Electrolytes on the Enhanced Performances of Graphite Electrode for Lithium-Ion Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Jianming; Yan, Pengfei; Cao, Ruiguo; Xiang, Hongfa; Engelhard, Mark H.; Polzin, Bryant; Wang, Chong M.; Zhang, Jiguang; Xu, Wu

    2016-02-10

    Cesium salt has been demonstrated as an efficient electrolyte additive in suppressing the lithium (Li) dendrite formation and directing the formation of an ultrathin and stable solid electrolyte interphase (SEI) even in propylene carbonate (PC)-ethylene carbonate (EC)-based electrolytes. Here, we further investigate the effect of PC content in the presence of CsPF6 additive (0.05 M) on the performances of graphite electrode in Li||graphite half cells and in graphite||LiNi0.80Co0.15Al0.05O2 (NCA) full cells. It is found that the performance of graphite electrode is also affected by PC content even though CsPF6 additive is present in the electrolytes. An optimal PC content of 20% by weight in the solvent mixtures is identified. The enhanced electrochemical performance of graphite electrode is attributed to the synergistic effects of the Cs+ additive and the PC solvent. The formation of a robust, ultrathin and compact SEI layer containing lithium-enriched species on the graphite electrode, directed by Cs+, effectively suppresses the PC co-intercalation and thus prevents the graphite exfoliation. This SEI layer is only permeable for de-solvated Li+ ions and allows fast Li+ ion transport through it, which therefore largely alleviates the Li dendrite formation on graphite electrode during lithiation even at high current densities. The presence of low-melting-point PC solvent also enables the sustainable operation of the graphite||NCA full cells under a wide spectrum of temperatures. The fundamental findings of this work shed light on the importance of manipulating/maintaining the electrode/electrolyte interphasial stability in a variety of energy storage devices.

  8. Lithium neurotoxicity.

    Science.gov (United States)

    Suraya, Y; Yoong, K Y

    2001-09-01

    Inspite of the advent of newer antimanic drugs, lithium carbonate remains widely used in the treatment and prevention of manic-depressive illness. However care has to be exercised due to its low therapeutic index. The central nervous system and renal system are predominantly affected in acute lithium intoxication and is potentially lethal. The more common side effect involves the central nervous system. It occurs early and is preventable. We describe three cases of lithium toxicity admitted to Johor Bahru Hospital, with emphasis on its neurological preponderance.

  9. Elimination Reactions of (E)-2,4,6-Trinitrobenzaldehyde O-benzoyloximes Promoted by R2NH in MeCN. Change of Reaction Mechanism

    International Nuclear Information System (INIS)

    Cho, Bong Rae; Pyun, Sang Yong

    2010-01-01

    We have studied the nitrile-forming elimination reactions from 1 promoted by R 2 NH in MeCN. The reaction proceeded by (E1cb) irr mechanism. Change of the β-aryl group from 2,4-dinitrophenyl to a more strongly electron-withdrawing 2,4,6-trinitrophenyl increased the reaction rate by 470-fold, shifted the transition state toward more reactant-like, and changed the reaction mechanism from E2 to (E1cb) irr . To the best of our knowledge, this is the first example of nitrile-forming elimination reaction that proceeds by the (E1cb) irr mechanism in MeCN. Noteworthy is the carbanion stabilizing ability of the 2,4,6-trinitrophenyl group in aprotic solvent. Nitrile-forming elimination reactions of (E)-benzaldoxime derivatives have been extensively investigated under various conditions. The reactions proceeded by the E2 mechanism in MeCN despite the fact that the reactants have syn stereochemistry, poor leaving, and sp 2 hybridized β-carbon atom, all of which favor E1cb- or E1cb-like transition state. Moreover, the transition state structures were relatively insensitive to the variation of the reactant structures. The results have been attributed to the poor anion solvating ability of MeCN, which favors E2 transition state with maximum charge dispersal. For eliminations from strongly activated (E)-2,4-(NO 2 ) 2 C 6 H 3 CH=NOC(O)C 6 H 4 X, a change in the reaction mechanism from E2 to (E1cb) irr was observed as the base-solvent was changed from R 2 NH in MeCN to R 2 NH/R 2 NH 2 + in 70 mol % MeCN(aq). A combination of a strong electron-withdrawing β-aryl group and anion-solvating protic solvent was required for the mechanistic change

  10. Hierarchical Mesoporous Lithium-Rich Li[Li0.2Ni0.2Mn0.6]O2 Cathode Material Synthesized via Ice Templating for Lithium-Ion Battery.

    Science.gov (United States)

    Li, Yu; Wu, Chuan; Bai, Ying; Liu, Lu; Wang, Hui; Wu, Feng; Zhang, Na; Zou, Yufeng

    2016-07-27

    Tuning hierarchical micro/nanostructure of electrode materials is a sought-after means to reinforce their electrochemical performance in the energy storage field. Herein, we introduce a type of hierarchical mesoporous Li[Li0.2Ni0.2Mn0.6]O2 microsphere composed of nanoparticles synthesized via an ice templating combined coprecipitation strategy. It is a low-cost, eco-friendly, and easily operated method using ice as a template to control material with homogeneous morphology and rich porous channels. The as-prepared material exhibits remarkably enhanced electrochemical performances with higher capacity, more excellent cycling stability and more superior rate property, compared with the sample prepared by conventional coprecipitation method. It has satisfactory initial discharge capacities of 280.1 mAh g(-1) at 0.1 C, 207.1 mAh g(-1) at 2 C, and 152.4 mAh g(-1) at 5 C, as well as good cycle performance. The enhanced electrochemical performance can be ascribed to the stable hierarchical microsized structure and the improved lithium-ion diffusion kinetics from the highly porous structure.

  11. Stabilized Lithium-Metal Surface in a Polysulfide-Rich Environment of Lithium-Sulfur Batteries.

    Science.gov (United States)

    Zu, Chenxi; Manthiram, Arumugam

    2014-08-07

    Lithium-metal anode degradation is one of the major challenges of lithium-sulfur (Li-S) batteries, hindering their practical utility as next-generation rechargeable battery chemistry. The polysulfide migration and shuttling associated with Li-S batteries can induce heterogeneities of the lithium-metal surface because it causes passivation by bulk insulating Li2S particles/electrolyte decomposition products on a lithium-metal surface. This promotes lithium dendrite formation and leads to poor lithium cycling efficiency with complicated lithium surface chemistry. Here, we show copper acetate as a surface stabilizer for lithium metal in a polysulfide-rich environment of Li-S batteries. The lithium surface is protected from parasitic reactions with the organic electrolyte and the migrating polysulfides by an in situ chemical formation of a passivation film consisting of mainly Li2S/Li2S2/CuS/Cu2S and electrolyte decomposition products. This passivation film also suppresses lithium dendrite formation by controlling the lithium deposition sites, leading to a stabilized lithium surface characterized by a dendrite-free morphology and improved surface chemistry.

  12. Polyethylene oxide film coating enhances lithium cycling efficiency of an anode-free lithium-metal battery.

    Science.gov (United States)

    Assegie, Addisu Alemayehu; Cheng, Ju-Hsiang; Kuo, Li-Ming; Su, Wei-Nien; Hwang, Bing-Joe

    2018-03-29

    The practical implementation of an anode-free lithium-metal battery with promising high capacity is hampered by dendrite formation and low coulombic efficiency. Most notably, these challenges stem from non-uniform lithium plating and unstable SEI layer formation on the bare copper electrode. Herein, we revealed the homogeneous deposition of lithium and effective suppression of dendrite formation using a copper electrode coated with a polyethylene oxide (PEO) film in an electrolyte comprising 1 M LiTFSI, DME/DOL (1/1, v/v) and 2 wt% LiNO3. More importantly, the PEO film coating promoted the formation of a thin and robust SEI layer film by hosting lithium and regulating the inevitable reaction of lithium with the electrolyte. The modified electrode exhibited stable cycling of lithium with an average coulombic efficiency of ∼100% over 200 cycles and low voltage hysteresis (∼30 mV) at a current density of 0.5 mA cm-2. Moreover, we tested the anode-free battery experimentally by integrating it with an LiFePO4 cathode into a full-cell configuration (Cu@PEO/LiFePO4). The new cell demonstrated stable cycling with an average coulombic efficiency of 98.6% and capacity retention of 30% in the 200th cycle at a rate of 0.2C. These impressive enhancements in cycle life and capacity retention result from the synergy of the PEO film coating, high electrode-electrolyte interface compatibility, stable polar oligomer formation from the reduction of 1,3-dioxolane and the generation of SEI-stabilizing nitrite and nitride upon lithium nitrate reduction. Our result opens up a new route to realize anode-free batteries by modifying the copper anode with PEO to achieve ever more demanding yet safe interfacial chemistry and control of dendrite formation.

  13. Measuring nanocurie quantities of tritium bred in metallic lithium and lithium oxide samples

    International Nuclear Information System (INIS)

    Bertone, P.C.

    1985-01-01

    The LBM program requires that nanocurie quantities of tritium, bred in both lithium oxide pellets and lithium samples, be measured with an uncertainty not exceeding + or - 6%. Two methods of accurately measuring nanocurie quantities of tritium bred in LBM lithium oxide pellets and one method of accurately measuring nanocurie quantities of tritium bred in lithium samples are described. Potential errors associated with these tritium measurement techniques are also discussed

  14. Measurement of 6Li(n,α)3H reaction cross section

    International Nuclear Information System (INIS)

    Renner, C.

    1979-01-01

    The 6 Li(n,α) 3 H reaction cross section was measured at 12 discrete neutron energies between 80 KeV and 470 KeV by using the Oak Ridge Linear Acelerator (ORELA) as a pulsed neutron source. The neutron beam was filtered through 20 cm or 30 cm of Armco iron which produces several monoenergetic energies groups (iron windows) between 20 KeV and 1000 KeV about 2 KeV wide. The (n,α) events were detected by a 1 mm thick Li-glass scintillator and the neutron flux was measured with a NE110 plastic scintillator 6,6 cm thick and 10 cm in diameter. Multiple scattering corrections in the Li-glass and the NE110 scintillator efficiency were determined theoretically by using Monte Carlo technique. The 6 Li content in the Li-glasses was determined by transmission measurements with low energy neutrons. A theoretical fit was applied to the results by the R-matrix theory. (Author) [pt

  15. The (p→,t) reaction on 58Ni and 56Fe at 24.6 MeV

    International Nuclear Information System (INIS)

    Polane, J.H.; Feix, W.F.; Hall, P.J. van; Klein, S.S.; Nijgh, G.J.; Poppema, O.J.; Wassenaar, S.D.

    1989-01-01

    The (p, t) reactions on 56 Fe and 58 Ni initiated by 24.6 MeV polarised protons has been investigated. The reaction process is described in terms of simultaneous and sequential neutron transfer. For all five final states studied the sequential process competes strongly with simultaneous transfer of a neutron pair. Theoretical values for the spectroscopic amplitudes were derived from shell-model wavefunctions; these seem to give a reliable description of the reaction process. (author)

  16. Mechanisms of the p(He 6,He 5)d, p(He 6,α)t and p(He 6,t)α reactions

    International Nuclear Information System (INIS)

    Heiberg-Andersen, Henning

    2002-07-01

    This work was devoted to nucleon induced transfer reactions having the potential to probe the sub-cluster structures of the benchmark halo nucleus He 6, without the question marks the necessarily omitted exchange effects tend to put behind the CRC results when both collision partners are composite systems. Still, the exchange complications entered the analysis in an ironic way: The high Q-value of the p(He 6,α)t and p(He 6, t)α reactions caused sensitivity to the t - α optical potential at small radii, where the one-nucleon exchange effects are strongest. Since the attempt to throw them out of the extracted tau - α potential failed, it was necessary to extend the model space to avoid a too difficult modelling of the local equivalent t - α potential. By this step, all the complications originating from antisymmetrization within a larger model space entered the analysis. However, the persistent failures of the two-channel calculations of this and previous works can hardly be due to incorrect treatment of exchange effects only, so the loss of simplicity is probably illusory. Even at small angles, where the surface processes dominate, none of the two-channel calculations with various choices of t - α optical potentials managed to reproduce the p(He 6, α)t (p(He 6,t)α) data. This motivated inclusion of sequential transfers through the d + He 5 channel, where the sequential triton transfer process, included just for consistency in the coupling scheme of the four-channel calculation, turned out to be more influent than expected. The satisfactory reproduction of both the p(He 6, He 5)d and the p(He 6,α)t (p(He 6,t)α) data by the four-channel approach and the required re-normalization the real part of the p - He 6 optical potential are strong indications of substantial contributions from sequential transfer of the halo neutrons at this energy. The conclusions that can be drawn from this work are limited by the modest amount of available data. This limitation does

  17. Mechanisms of the p(He 6,He 5)d, p(He 6,{alpha})t and p(He 6,t){alpha} reactions

    Energy Technology Data Exchange (ETDEWEB)

    Heiberg-Andersen, Henning

    2002-07-01

    This work was devoted to nucleon induced transfer reactions having the potential to probe the sub-cluster structures of the benchmark halo nucleus He 6, without the question marks the necessarily omitted exchange effects tend to put behind the CRC results when both collision partners are composite systems. Still, the exchange complications entered the analysis in an ironic way: The high Q-value of the p(He 6,{alpha})t and p(He 6, t){alpha} reactions caused sensitivity to the t - {alpha} optical potential at small radii, where the one-nucleon exchange effects are strongest. Since the attempt to throw them out of the extracted tau - {alpha} potential failed, it was necessary to extend the model space to avoid a too difficult modelling of the local equivalent t - {alpha} potential. By this step, all the complications originating from antisymmetrization within a larger model space entered the analysis. However, the persistent failures of the two-channel calculations of this and previous works can hardly be due to incorrect treatment of exchange effects only, so the loss of simplicity is probably illusory. Even at small angles, where the surface processes dominate, none of the two-channel calculations with various choices of t - {alpha} optical potentials managed to reproduce the p(He 6, {alpha})t (p(He 6,t){alpha}) data. This motivated inclusion of sequential transfers through the d + He 5 channel, where the sequential triton transfer process, included just for consistency in the coupling scheme of the four-channel calculation, turned out to be more influent than expected. The satisfactory reproduction of both the p(He 6, He 5)d and the p(He 6,{alpha})t (p(He 6,t){alpha}) data by the four-channel approach and the required re-normalization the real part of the p - He 6 optical potential are strong indications of substantial contributions from sequential transfer of the halo neutrons at this energy. The conclusions that can be drawn from this work are limited by the

  18. Cyclisation versus 1,1-Carboboration: Reactions of B(C6F5)3 with Propargyl Amides.

    Science.gov (United States)

    Melen, Rebecca L; Hansmann, Max M; Lough, Alan J; Hashmi, A Stephen K; Stephan, Douglas W

    2013-09-02

    A series of propargyl amides were prepared and their reactions with the Lewis acidic compound B(C6F5)3 were investigated. These reactions were shown to afford novel heterocycles under mild conditions. The reaction of a variety of N-substituted propargyl amides with B(C6F5)3 led to an intramolecular oxo-boration cyclisation reaction, which afforded the 5-alkylidene-4,5-dihydrooxazolium borate species. Secondary propargyl amides gave oxazoles in B(C6F5)3 mediated (catalytic) cyclisation reactions. In the special case of disubstitution adjacent to the nitrogen atom, 1,1-carboboration is favoured as a result of the increased steric hindrance (1,3-allylic strain) in the 5-alkylidene-4,5-dihydrooxazolium borate species. Copyright © 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Lithium-Oxygen Batteries: At a Crossroads?

    DEFF Research Database (Denmark)

    Vegge, Tejs; García Lastra, Juan Maria; Siegel, Donald Jason

    2017-01-01

    In this current opinion, we critically review and discuss some of the most important recent findings in the field of rechargeable lithium-oxygen batteries. We discuss recent discoveries like the evolution of reactive singlet oxygen and the use of organic additives to bypass reactive LiO2 reaction...... intermediates, and their possible implications on the potential for commercialization of lithium-oxygen batteries. Finally, we perform a critical assessment of lithium-superoxide batteries and the reversibility of lithium-hydroxide batteries....

  20. Lithium aluminates and tritium production

    International Nuclear Information System (INIS)

    Carrera G, L.M.; Palacios G, O.; Bosch G, P.

    1997-01-01

    In this work it is studied the crystalline structure of lithium aluminates prepared by three different methods, namely: solid state reaction, humid reaction and sol-gel reaction. The analysis methods are the X-ray diffractometry and the scanning and transmission electron microscopy. This study is realized as in original materials as in irradiated materials at the TRIGA Mark reactor, to correlate the synthesis method with response of these materials to the mixed irradiation of nuclear reactor. (Author)

  1. Highly selective reactions of C(60)Cl(6) with thiols for the synthesis of functionalized [60]fullerene derivatives

    OpenAIRE

    Khakina, Ekaterina A; Yurkova, Anastasiya A; Peregudov, Alexander S; Troyanov, Sergey I; Trush, Vyacheslav V; Vovk, Andrey I; Mumyatov, Alexander V; Martynenko, Vyacheslav M; Balzarini, Jan; Troshin, Pavel A

    2012-01-01

    Chlorofullerene C(60)Cl(6) undergoes highly selective reactions with thiols forming compounds C(60)[SR](5)H with high yields. These reactions open up straightforward synthetic routes to many functionalized fullerene derivatives, e.g. water-soluble compounds showing interesting biological activities.

  2. Reaction rate studies of glucose-6-phosphate dehydrogenase activity in sections of rat liver using four tetrazolium salts

    NARCIS (Netherlands)

    Butcher, R. G.; van Noorden, C. J.

    1985-01-01

    The reaction rate of glucose-6-phosphate dehydrogenase activity in liver sections from fed and starved rats has been monitored by the continuous measurement at 37 degrees C of the reaction product as it is formed using scanning and integrating microdensitometry. Control media lacked either substrate

  3. Dual level reaction-path dynamics calculations on the C2H6 + OH → C2H5 + H2O reaction

    International Nuclear Information System (INIS)

    Coitino, E.L.; Truhlar, D.G.

    1996-01-01

    Interpolated Variational Transition State Theory with Multidimensional Tunneling contributions (IVTST/MT) has been applied to the reaction of C 2 H 6 + OH, and it yields rate constants that agree well with the available experimental information. The main disadvantage of this method is the difficulty of interpolating all required information from a few points along the reaction path. A more recent alternative is Variational Transition State Theory with Multidimensional Tunneling and Interpolated Corrections (VTST/MT-IC, also called dual-level direct dynamics), in which the reaction-path properties are first determined at an economical (lower) level of theory and then open-quotes correctedclose quotes using more accurate information obtained at a higher level for a selected number of points on the reaction path. The VTST/MT-IC method also allows for interpolation through die wider reaction swath when large-curvature tunneling occurs. In the present work we examine the affordability/accuracy tradeoff for several combinations of higher and lower levels for VTST/MT-IC reaction rate calculations on the C 2 H 6 + OH process. Various levels of theory (including NDDO-SRP and ab initio ROMP2, UQCISD, UQCISD(T), and UCCSD) have been employed for the electronic structure calculations. We also compare several semiclassical approaches implemented in the POLYRATE and MORATE programs for taking tunneling effects into account

  4. Coupled-reaction-channel analysis of the (d,6Li) reaction on 24Mg and 26Mg to low-lying states

    International Nuclear Information System (INIS)

    Oelert, W.

    1986-01-01

    Experimental spectroscopic factors of the alpha-transfer reaction on nuclei of the sd-shell show rather strong inconsistencies and scatter much more strongly than explainable by the quoted errors. The poorer the quality of agreement between experimental and theoretical angular distribution shapes, the more inconsistent the comparison of spectroscopic factors either between different experiments or between theory and experiment. In view of the strong deformation of nuclei in the lower part of the sd-shell, higher-order reaction mechanisms are expected. A coupled-reaction-channel analysis for the transitions to the 0 + , 2 + , and 4 + states of the ground-state bands in 20 Ne and 22 Ne excited via the (d, 6 Li) reaction yields good agreement between experimental and theoretical angular distribution shapes as well as spectroscopic information. (orig.)

  5. SU-F-T-140: Assessment of the Proton Boron Fusion Reaction for Practical Radiation Therapy Applications Using MCNP6

    Energy Technology Data Exchange (ETDEWEB)

    Adam, D; Bednarz, B [University of Wisconsin, Madison, WI (United States)

    2016-06-15

    Purpose: The proton boron fusion reaction is a reaction that describes the creation of three alpha particles as the result of the interaction of a proton incident upon a 11B target. Theoretically, the proton boron fusion reaction is a desirable reaction for radiation therapy applications in that, with the appropriate boron delivery agent, it could potentially combine the localized dose delivery protons exhibit (Bragg peak) and the local deposition of high LET alpha particles in cancerous sites. Previous efforts have shown significant dose enhancement using the proton boron fusion reaction; the overarching purpose of this work is an attempt to validate previous Monte Carlo results of the proton boron fusion reaction. Methods: The proton boron fusion reaction, 11B(p, 3α), is investigated using MCNP6 to assess the viability for potential use in radiation therapy. Simple simulations of a proton pencil beam incident upon both a water phantom and a water phantom with an axial region containing 100ppm boron were modeled using MCNP6 in order to determine the extent of the impact boron had upon the calculated energy deposition. Results: The maximum dose increase calculated was 0.026% for the incident 250 MeV proton beam scenario. The MCNP simulations performed demonstrated that the proton boron fusion reaction rate at clinically relevant boron concentrations was too small in order to have any measurable impact on the absorbed dose. Conclusion: For all MCNP6 simulations conducted, the increase of absorbed dose of a simple water phantom due to the 11B(p, 3α) reaction was found to be inconsequential. In addition, it was determined that there are no good evaluations of the 11B(p, 3α) reaction for use in MCNPX/6 and further work should be conducted in cross section evaluations in order to definitively evaluate the feasibility of the proton boron fusion reaction for use in radiation therapy applications.

  6. Alpha cluster states in light nuclei populated through the (6Li,d) reaction

    Energy Technology Data Exchange (ETDEWEB)

    Borello-Lewin, Thereza; Rodrigues, M.R.D.; Horodynski-Matsushigue, L.B.; Duarte, J.L.M.; Rodrigues, C.L.; Souza, M.A. [Universidade de Sao Paulo (IF/USP), SP (Brazil). Inst. de Fisica; Cunsolo, A.; Cappuzzello, F. [Universita di Catania (Italy). Istituto Nazionale di Fisica Nucleare. Lab. Nazionali del Sud; Ukita, Gilberto Mitsuo [Universidade de Santo Amaro (UNISA), Sao Paulo, SP (Brazil). Fac. de Psicologia

    2011-07-01

    Full text: The alpha cluster correlation is an important concept in the nuclear physics of light nuclei. The main purpose of the research program in progress is the investigation of the alpha clustering phenomenon in (x{alpha}) and(x{alpha}+{nu}) nuclei through the ({sup 6}Li,d) alpha transfer reaction. In fact, there is scarce experimental information on the subject, in particular associated with resonant states predicted near (x{alpha}) and (x{alpha}+{nu}) thresholds. Measurements of the {sup 12},{sup 13}C({sup 6}Li,d) {sup 16},{sup 17}O reactions, at an incident energy of 25.5 MeV, have been performed employing the Sao Paulo Pelletron-Enge Split-Pole facility and the nuclear emulsion detection technique. The work is under way and an experimental energy resolution of 30 keV was obtained. Near the (4{alpha}) breakup threshold in {sup 16}O, three narrow alpha resonances, not previously measured, were detected, revealing important {alpha} + {sup 12}C(G.S.) components. One of these resonances corresponds to the known 0{sup +} state at 15.1 MeV[5] of excitation that has probably, according to Funaki et al., the gas like configuration of the 4{alpha} condensate state, with a very dilute density and a large component of {alpha} + {sup 12}C(Hoyle) configuration. As was already mentioned, our experimental information points to the necessity of including the {alpha} + {sup 12}C(G.S.) component in the wave function. (author)

  7. Modeling the Lithium Ion Battery

    Science.gov (United States)

    Summerfield, John

    2013-01-01

    The lithium ion battery will be a reliable electrical resource for many years to come. A simple model of the lithium ions motion due to changes in concentration and voltage is presented. The battery chosen has LiCoO[subscript 2] as the cathode, LiPF[subscript 6] as the electrolyte, and LiC[subscript 6] as the anode. The concentration gradient and…

  8. Synthesis of substituted Calix[6] arene and 18F labeling reaction as catalyst in preparation of 18F-FET

    International Nuclear Information System (INIS)

    Peng Cheng; Ma Yunchuan; Chen Xiaoxiao; Li Guixia; Li Shilei; Zhang Shuting; He Yong; Qi Chuanmin

    2011-01-01

    The phase transfer catalyst Substituted Calix[6] arene was prepared and it was used as catalyst to prepare the tumor diagnostic drug 18 F-FET. The results showed that para-sulfonated-calix[6] arene not only catalyzes 19 F substitution reaction, but also catalyzes 18 F labelling reaction with radiochemical yield of 11%. However, para-tert-butyl-calix[6] arene has no catalytic activity for the 19 F substitution reaction nor the 18 F labelling reaction of the precursor of FET. The catalyzing of para-sulfonated-calix[6]arene may be related to it's sulfonate groups, which participated in the coordination reaction and increased the polarity of calyx[6] arene and so on. Although radiochemical yield of the para-sulfonated-calix[6] arene catalyzed 18 F labeling of the precursor of FET was much lower than that obtained by Kryptofix 2. 2. 2, this study still has significant meaning for us to find better substituted Calix[6] arene catalysts by optimizing the reaction conditions. (authors)

  9. Synthesis and reactions of 4-(p-methoxybenzyl-6-[5,6,7,8-tetrahydro-2-naphthyl]-pyridazin-3(2H-one

    Directory of Open Access Journals (Sweden)

    NAGWA M.S. EL-DIN HARB

    1999-11-01

    Full Text Available The condensation of 4-(p-methoxybenzyl-6-[5,6,7,8-tetrahydro-2-naphthyl]-pyridazin-3(2H-one (3, prepared by the reaction of 6-[5,6,7,8-tetrahydro-2-naphthyl]-4,5-dihydropyridazin-3(2H-one (1 and anisaldehyde, with dimethyl sulphate, formaldehyde and acrylonitrile, and also the formation of the Mannich base, proceeded smoothly at the 2-position to give compounds 4,5,6,7, respectively. 4-p-Methoxybenzyl-3-chloro-6-[5,6,7,8-tetrahydro-2-naphthyl]-pyridazine (9 was prepared in law yield by the action of phosphorus oxychloride on 3. The reaction of 9 with benzylamine, aniline and piperidine gave 10a,b,c, respectively. 4-p-Methoxybenzyl-6-[5,6,7,8-tetrahydro-2-napthyl]pyridazine-3(2H-thione (12 was prepared either by the action of thiourea on 9, or by the reaction of 3 with phosphorus pentasulphide. The reaction of these thiones with acrylonitrile, morpholine and piperidine to give 13 and 14 a,b, respectively, were also investigated.

  10. Electrical conductivity and reaction with lithium of LiFe{sub 1-y}Mn{sub y}PO{sub 4} olivine-type cathode materials

    Energy Technology Data Exchange (ETDEWEB)

    Molenda, J.; Ojczyk, W.; Marzec, J. [Faculty of Materials Science and Ceramics, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland)

    2007-12-06

    Structural, electrical and electrochemical properties of Mn-substituted phospho-olivines LiFe{sub 1-y}Mn{sub y}PO{sub 4} were investigated and compared to those of LiFePO{sub 4}. Rietvield refined XRD patterns taken in the course of delithiation process showed apparent difference between phase compositions of these cathode materials upon lithium extraction. Contrary to the LiFePO{sub 4} and LiMnPO{sub 4} compositions for which a two-phase mechanism of electrochemical lithium extraction/insertion is observed, in case of Mn-substituted LiFe{sub 1-y}Mn{sub y}PO{sub 4} samples a single-phase mechanism of deintercalation was observed in the studied range of lithium concentration. Electrochemical characterization of the cathode materials were performed in Li/Li{sup +}/Li{sub x}Fe{sub 1-y}Mn{sub y}PO{sub 4}-type cells for y = 0.0, 0.25, 0.55, 0.75 and 1.0 compositions. Voltammery studies showed low reversibility of the lithium extraction process in the high-voltage ''manganese'' range, while in the ''iron'' range the reversibility of lithium extraction is high. Impedance measurements of the LiFe{sub 1-y}Mn{sub y}PO{sub 4} cathode materials, which enabled separation of the ionic and electronic components of their entire electrical conductivity, showed distinct influence of Mn content on the electronic part of conductivity. EIS measurements performed at different states of cell charge revealed that the charge-transfer impedance in Li{sub x}Fe{sub 1-y}Mn{sub y}PO{sub 4} is much lower than that of Li{sub x}FePO{sub 4}. (author)

  11. Evidence for leading mesons in anti p4He reactions at 0.6 GeV/c incident momentum

    International Nuclear Information System (INIS)

    Breivik, F.O.; Haatuft, A.; Halsteinslid, A.

    1990-05-01

    In a previous report, evidence has been shown for leading mesons in anti p Ne - reactions at 0.6 Gev/c incident momentum. In this report evidence is shown for leading mesons in anti p 4 He reactions at the same incident momentum, based on data from the same detector. In anti p Ne - reactions, only kaons are observed as leading mesons in K o s-events, and only pions are observed as leading mesons in Λ o -events. In anti p He - reactions this is not longer true, since also pions behave as leading mesons in K o s-events. 5 refs., 9 figs

  12. A study on structure defects in irradiated lithium fluoride (thermal neutrons); Etude des imperfections de structure du fluorure de lithium irradie (neutrons thermiques)

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, M

    1958-06-19

    A study was made of the behavior of atomic defects, vacancies and interstitials, generated from the Li{sup 6}(n,{alpha})H{sup 3} reaction in Lip crystals. Defects appear as cavities and platelets around ten angstrom in size and increase both with neutron dose and annealing temperature. For longer irradiations, metallic lithium precipitates out, in epitaxy with LiF lattice, and later, lithium salts appear due to the penetration of atmospheric gases through the cracks present in the damaged crystal. Various x-ray experiments followed the formation and evolution of these imperfections when their atomic concentration reached 10{sup -4}. (author)

  13. Interfacial reaction in SiC_f/Ti-6Al-4V composite by using transmission electron microscopy

    International Nuclear Information System (INIS)

    Huang, Bin; Li, Maohua; Chen, Yanxia; Luo, Xian; Yang, Yanqing

    2015-01-01

    The interfacial reactions of continuous SiC fiber reinforced Ti-6Al-4V matrix composite (SiC_f/Ti-6Al-4V composite) and continuous SiC fiber coated by C reinforced Ti-6Al-4V matrix composite (SiC_f/C/Ti-6Al-4V composite) were investigated by using micro-beam electron diffraction (MBED) and energy disperse spectroscopy (EDS) on transmission electron microscopy (TEM). The sequence of the interfacial reactions in the as-processed and exposed at 900°C for 50h SiC_f/Ti-6Al-4V composites can be described as SiC||TiC||Ti_5Si_3 + TiC||Ti-6Al-4V and SiC||TiC||Ti_5Si_3||TiC||Ti_5Si_3||TiC||Ti_5Si_3||Ti-6Al-4V, respectively. Additionally, both in as-processed and exposed composites, Ti_3SiC_2 and Ti_3Si are absent at the interfaces. For the SiC_f/C/Ti-6Al-4V composite exposed at 900 °C for 50 h, the sequence of the interfacial reaction can be described as SiC||C||TiC_F||TiC_C||Ti-6Al-4V before C coating is completely consumed by interfacial reaction. When interfacial reaction consumes C coating completely, the sequence of the interfacial reaction can be described as SiC||TiC||Ti_5Si_3||TiC||Ti-6Al-4V. Furthermore, in SiC_f/C/Ti-6Al-4V composite, C coating can absolutely prevent Si diffusion from SiC fiber to matrix. Basing on these results, the model of formation process of the interfacial reaction products in the composites was proposed. - Highlights: • We obtained the sequence of the interfacial reactions in the as-processed and exposed at 900 °C for 50 h SiC_f/Ti-6Al-4 V composites as well as in the SiC_f/C/Ti-6Al-4 V composite exposed at 900 °C for 50 h. • We verified that both in as-processed and exposed SiC_f/Ti-6Al-4 V composites, Ti_3SiC_2 and Ti_3Si are absent at the interfaces. • Carbon coating can absolutely prevent silicon diffusion from SiC fiber to matrix. • Basing on these results, the model of formation process of the interfacial reaction products in the composites was proposed.

  14. Experimental investigation of highly excited states of the 5,6He and 5,6Li nuclei in the (6Li, 7Be) and (6Li, 7Li) one-nucleon-pick-up reactions

    International Nuclear Information System (INIS)

    Sakuta, S.B.; Novatskij, B.G.; Stepanov, D.N.; Aleksandrov, D.V.; Glukhov, Yu.A.; Nikol'skij, E.Yu.

    2002-01-01

    ( 6 Li, 7 Be) and ( 6 Li, 7 Li) reactions on the 6 Li, 7 Li nuclei have been investigated in the angular range of 0-20 deg in laboratory system at the 93-MeV 6 Li energy. Besides low-lying states of 5,6 He and 5,6 Li nuclei, broad structures have been observed in the measured spectra close to the t( 3 He) + d and t( 3 He) + t threshold at excitation energies of 16.75 (3/2 + ) and ∼ 20 MeV ( 5 He), 16.66 (3/2 + ) and ∼ 20 MeV ( 5 Li), 14.0 and 25 MeV ( 6 He), and ∼ 20 MeV ( 6 Li). Angular distributions, which have been measured for transitions to the ground (0 + ) and exited states at E x =1.8 MeV (2 + ) and 14.0 MeV of the 6 He nucleus in the 7 Li( 6 Li, 7 Be) 6 He reaction, have been analyzed in the framework of the finite-range distorted-waves method assuming the 1p- and 1s-proton pick-up mechanism. It has been shown that ( 6 Li, 7 Be) and ( 6 Li, 7 Li) reactions predominately proceed by one-step pick-up mechanism and broad structures which are observed at high excitation energies should be considered as quasimolecular states of the t( 3 He) + d and t( 3 He) + t type [ru

  15. Multiphoton Ionization of Laser Cooled Lithium

    OpenAIRE

    Steinmann, Jochen

    2007-01-01

    Reaction microscopes enable kinematically complete measurements of atomic and molecular fragmentation. An ultracold atomic target is usually provided by a supersonic gas jet. The apparatus developed in the course of this thesis for the first time combines the principle of the reaction microscope with a magneto-optical trap. This allows for the preparation of lithium atoms in the sub-mK range. Being a three-electron system, its simple atomic structure makes lithium a model system of great topi...

  16. Expression of interleukin-1β and interleukin-6 in leprosy reactions in patients with human immunodeficiency virus coinfection.

    Science.gov (United States)

    Pires, Carla Andréa Avelar; Quaresma, Juarez Antônio Simões; de Souza Aarão, Tinara Leila; de Souza, Jorge Rodrigues; Macedo, Geraldo Mariano Moraes; Neto, Fernando Octávio Machado Jucá; Xavier, Marília Brasil

    2017-08-01

    Previous studies suggest that coinfection of leprosy and human immunodeficiency virus (HIV) does not decrease the frequency and intensity of leprosy reactions. However, the immunological aspects of leprosy reactions in coinfected patients remain obscure, with a limited number of studies showing contradictory results. Observational study using tissue samples collected during leprosy reactions from 15 patients coinfected with leprosy and HIV and from 15 patients with leprosy alone. Patients were part of a prior larger cohort study of leprosy patients with and without HIV coinfection. Specific antibodies were used to detect IL-1β and IL-6 expression in skin biopsy tissue cells. IL-1β and IL-6 expression was similar between leprosy patients with and without HIV coinfection (p>0.05). Coinfected and non-coinfected tissues showed similar levels of IL-1β and IL-6 expression for type 1 reactions. A trend towards increased levels of IL-1β and IL-6 expression was observed in tissue from coinfected patients (p=0.0024). The expression of IL-1β and IL-6 during leprosy reactions did not differ significantly between tissues obtained from leprosy patients with and without HIV coinfection. Therefore, we conclude that HIV coinfection does not affect the immunological pattern of leprosy reactions. Copyright © 2017. Published by Elsevier B.V.

  17. Effects of Propylene Carbonate Content in CsPF 6 -Containing Electrolytes on the Enhanced Performances of Graphite Electrode for Lithium-Ion Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Jianming; Yan, Pengfei; Cao, Ruiguo; Xiang, Hongfa [School of; Engelhard, Mark H.; Polzin, Bryant J. [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439, United States; Wang, Chongmin; Zhang, Ji-Guang; Xu, Wu

    2016-02-15

    The effects Of propylene carbonate (PC) content in CsPF6-containing electrolytes on the performances of graphite electrode in lithium half cells and in graphite parallel to LiNi0.80Co0.15Al0.05O2 (NCA) full cells are investigated. It is found that the performance of graphite electrode is significantly-affected by PC content in the CsPF6-containing electrolytes. An optimal PC content of 20% by weight in the solvent mixtures is identified. The enhanced electrochemical performance of graphite electrode can be attributed to the synergistic effects of the PC solvent and the Cs+ additive. The synergistic effects of Cs+ additive and appropriate amount of PC enable the formation of a robust, ultrathin, and compact solid electrolyte interphase (SEI) layer on the surface of graphite electrode, which is only permeable for desolvated Li+ ions and allows fast Li+ ion transport through it. Therefore, this SEI layer effectively suppresses the PC cointercalation and largely alleviates the Li dendrite formation on graphite electrode during lithiation even at relatively high current densities. The presence of low-melting-point PC solvent improves the sustainable operation of graphite parallel to NCA full cells under a wide temperature range. The fundamental findings also shed light On the importance of manipulating/maintaining the electrode/electrolyte interphasial stability in various energy-storage devices.

  18. Degradation reactions in SONY-type Li-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Roth, E.P.; Nagasubramanian, G.

    2000-07-01

    Thermal instabilities were identified in SONY-type lithium-ion cells and correlated with interactions of cell constituents and reaction products. Three temperature regions of interaction were identified and associated with the state of charge (degree of Li intercalation) of the cell. Anodes were shown to undergo exothermic reactions as low as 100 C involving the solid electrolyte interface (SEI) layer and the LiPF{sub 6} salt in the electrolyte (EC:PC:DEC/LiPF{sub 6}). These reactions could account for the thermal runaway observed in these cells beginning at 100 C. Exothermic reactions were also observed in the 200 C--300 C region between the intercalated lithium anodes, the LiPF{sub 6} salt, and the PVDF. These reactions were followed by a high-temperature reaction region, 300 C--400 C, also involving the PVDF binder and the intercalated lithium anodes. The solvent was not directly involved in these reactions but served as a moderator and transport medium. Cathode exothermic reactions with the PVDF binder were observed above 200 C and increased with the state of charge (decreasing Li content). This offers an explanation for the observed lower thermal runaway temperatures for charged cells.

  19. Stability and isomerization reactions of phenyl cation C{sub 6}H{sub 5}{sup +} isomers

    Energy Technology Data Exchange (ETDEWEB)

    Shi, Dandan [Institute of Atomic and Molecular Physics, Jilin University, Changchun 130012 (China); Jilin Provincial Key Laboratory of Applied Atomic and Molecular Spectroscopy (Jilin University), Changchun 130012 (China); Yang, Xue [College of Science, Jilin Institute of Chemical Technology, Jilin 132022 (China); Zhang, Xiaomei; Shan, Shimin [Institute of Atomic and Molecular Physics, Jilin University, Changchun 130012 (China); Jilin Provincial Key Laboratory of Applied Atomic and Molecular Spectroscopy (Jilin University), Changchun 130012 (China); Xu, Haifeng, E-mail: xuhf@jlu.edu.cn [Institute of Atomic and Molecular Physics, Jilin University, Changchun 130012 (China); Jilin Provincial Key Laboratory of Applied Atomic and Molecular Spectroscopy (Jilin University), Changchun 130012 (China); Yan, Bing, E-mail: yanbing@jlu.edu.cn [Institute of Atomic and Molecular Physics, Jilin University, Changchun 130012 (China); Jilin Provincial Key Laboratory of Applied Atomic and Molecular Spectroscopy (Jilin University), Changchun 130012 (China)

    2016-03-01

    Highlights: • A total of 60 isomers of C{sub 6}H{sub 5}{sup +} cations were obtained at density functional theory. • The stability and isomerization reactions of C{sub 6}H{sub 5}{sup +} isomers were performed. • The structures, frequencies, thermodynamic properties of isomers were summarized. • Ring to ring or chain isomerization pathways were investigated using IRC method. • Result shows reactions contain hydrogen transfer, bond broken and reconstruction. - Abstract: As a key polyatomic molecular cation that plays a pivotal role in growth of the polycyclic aromatic hydrocarbons, phenyl cation C{sub 6}H{sub 5}{sup +} exhibits various isomers and isomerization reactions. Investigation on the structure and stability of the isomers as well as the isomerization is important for better understanding the chemical reactions involving C{sub 6}H{sub 5}{sup +} cations. In this work, we have performed a theoretical study on the stability and isomerization reactions of C{sub 6}H{sub 5}{sup +} isomers at density functional theory B3LYP/6-311G (d, p) level. We have obtained a total of 60 isomers of C{sub 6}H{sub 5}{sup +} cations, most of which are reported for the first time. The geometries, vibrational frequencies, thermodynamic properties and stability of 28 out of 60 isomers have been summarized in detail. Different ring-to-ring and ring-to-chain isomerization pathways, which are connected via 28 transition states, have been investigated using the intrinsic reaction coordinate method. The results show that the isomerization reactions occur via hydrogen migration followed by bond-breaking and reconstruction.

  20. Interactions of liquid lithium with various atmospheres, concretes, and insulating materials; and filtration of lithium aerosols

    International Nuclear Information System (INIS)

    Jeppson, D.W.

    1979-06-01

    This report describes the facilities and experiments and presents test results of a program being conducted at the hanford Engineering Development Laboratory (HEDL) in support of the fusion reactor development effort. This experimental program is designed to characterize the interaction of liquid lithium with various atmospheres, concretes, and insulating materials. Lithium-atmosphere reaction tests were conducted in normal humidity air, pure nitrogen, and carbon dioxide. These tests are described and their results, such as maximum temperatures, aerosol generated, and reaction rates measured, are reported. Initial lithium temperatures for these tests ranged between 224 0 C and 843 0 C. A lithium-concrete reaction test, using 10 kg of lithium at 327 0 C, and lithium-insulating materials reaction tests, using a few grams of lithium at 350 0 C and 600 0 C, are also described and results are presented. In addition, a lithium-aerosol filter loading test was conducted to determine the mass loading capacity of a commercial high efficiency particulate air (HEPA) filter. The aerosol was characterized, and the loading-capacity-versus-pressure-buildup across the filter is reported

  1. Molten salt synthesis of sodium lithium titanium oxide anode material for lithium ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Yin, S.Y., E-mail: yshy2004@hotmail.com [College of Environmental and Biological Engineering, Wuhan Technology and Business University, Wuhan 430065 (China); Feng, C.Q. [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry of Education Key Laboratory for Synthesis and Applications of Organic Functional Molecules, Hubei University, Wuhan 430062 (China); Wu, S.J.; Liu, H.L.; Ke, B.Q. [College of Environmental and Biological Engineering, Wuhan Technology and Business University, Wuhan 430065 (China); Zhang, K.L. [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China); Chen, D.H. [College of Environmental and Biological Engineering, Wuhan Technology and Business University, Wuhan 430065 (China); Hubei Key Laboratory for Catalysis and Material Science, College of Chemistry and Material Science, South Central University for Nationalities, Wuhan 430074, Hubei (China)

    2015-09-05

    Highlights: • Na{sub 2}Li{sub 2}Ti{sub 6}O{sub 12} has been successfully synthesized via a molten salt route. • Calcination temperature is an important effect on the component and microstructure of the product. • Pure phase Na{sub 2}Li{sub 2}Ti{sub 6}O{sub 12} could be obtained at 700 °C for 2 h. - Abstract: The sodium lithium titanium oxide with composition Na{sub 2}Li{sub 2}Ti{sub 6}O{sub 14} has been synthesized by a molten salt synthesis method using sodium chloride and potassium chloride mixture as a flux medium. Synthetic variables on the synthesis, such as sintering temperature, sintering time and the amount of lithium carbonate, were intensively investigated. Powder X-ray diffraction and scanning electron microscopy images of the reaction products indicates that pure phase sodium lithium titanium oxide has been obtained at 700 °C, and impure phase sodium hexatitanate with whiskers produced at higher temperature due to lithium evaporative losses. The results of cyclic voltammetry and discharge–charge tests demonstrate that the synthesized products prepared at various temperatures exhibited electrochemical diversities due to the difference of the components. And the sample obtained at 700 °C revealed highly reversible insertion and extraction of Li{sup +} and displayed a single potential plateau at around 1.3 V. The product obtained at 700 °C for 2 h exhibits good cycling properties and retains the specific capacity of 62 mAh g{sup −1} after 500 cycles.

  2. Possible production of glueballs in anti p-4He reactions at 0.6 GeV/c incident momentum

    International Nuclear Information System (INIS)

    Breivik, F.O.; Haatuft, A.; Halsteinslid, A.

    1990-08-01

    A fairly sharp peak at 1150 MeV/c 2 in the π - π + π - π + - system in the final state of anti p He-reactions at 0.6 GeV/c incident momentum is seen. The four-pion system may have spin = 0 or 2, which are possible spins of a glueball. 6 refs., 15 figs

  3. Genetic polymorphisms of the IL6 and NOD2 genes are risk factors for inflammatory reactions in leprosy.

    Science.gov (United States)

    Sales-Marques, Carolinne; Cardoso, Cynthia Chester; Alvarado-Arnez, Lucia Elena; Illaramendi, Ximena; Sales, Anna Maria; Hacker, Mariana de Andréa; Barbosa, Mayara Garcia de Mattos; Nery, José Augusto da Costa; Pinheiro, Roberta Olmo; Sarno, Euzenir Nunes; Pacheco, Antonio Guilherme; Moraes, Milton Ozório

    2017-07-01

    The pathways that trigger exacerbated immune reactions in leprosy could be determined by genetic variations. Here, in a prospective approach, both genetic and non-genetic variables influencing the amount of time before the development of reactional episodes were studied using Kaplan-Meier survival curves, and the genetic effect was estimated by the Cox proportional-hazards regression model. In a sample including 447 leprosy patients, we confirmed that gender (male), and high bacillary clinical forms are risk factors for leprosy reactions. From the 15 single nucleotide polymorphisms (SNPs) at the 8 candidate genes genotyped (TNF/LTA, IFNG, IL10, TLR1, NOD2, SOD2, and IL6) we observed statistically different survival curves for rs751271 at the NOD2 and rs2069845 at the IL6 genes (log-rank p-values = 0.002 and 0.023, respectively), suggesting an influence on the amount of time before developing leprosy reactions. Cox models showed associations between the SNPs rs751271 at NOD2 and rs2069845 at IL6 with leprosy reactions (HRGT = 0.45, p = 0.002; HRAG = 1.88, p = 0.0008, respectively). Finally, IL-6 and IFN-γ levels were confirmed as high, while IL-10 titers were low in the sera of reactional patients. Rs751271-GT genotype-bearing individuals correlated (p = 0.05) with lower levels of IL-6 in sera samples, corroborating the genetic results. Although the experimental size may be considered a limitation of the study, the findings confirm the association of classical variables such as sex and clinical forms with leprosy, demonstrating the consistency of the results. From the results, we conclude that SNPs at the NOD2 and IL6 genes are associated with leprosy reactions as an outcome. NOD2 also has a clear functional pro-inflammatory link that is coherent with the exacerbated responses observed in these patients.

  4. Investigation of the reaction 6Li + 40Ca at 156 MeV in a coincidence experiment

    International Nuclear Information System (INIS)

    Freindl, L.; Grotowski, K.; Uniwersytet Jagiellonski, Krakow; Planeta, R.; Klewe-Nebenius, H.; Neumann, B.; Buschmann, J.; Gils, H.J.; Rebel, H.; Zagromski, S.

    1983-12-01

    The cross sections for inelastic break up have been studied for the 6 Li + 40 Ca reaction at Esub(Li) = 156 MeV. For this, gamma ray spectra from the heavy residual nuclei were measured in coincidence with beam velocity projectile fragments. The cross sections were found to be: 34 +- 9 14 mb for protons, 30 +- 7 12 mb for deuterons, and 78 +- 41 142 mb for α-particles, respectively. These values are small when compared to total break up cross sections. A comparison of the cross section sum of all known reaction paths induced by 6 Li + 40 Ca at 156 MeV with total reaction cross section indicates a missing cross section of the order of a few hundred millibarns. It is discussed whether this cross section may be attributed to pick up reactions. (orig.) [de

  5. The tin-rich copper lithium stannides: Li3Cu6Sn4 and Li2CuSn2

    International Nuclear Information System (INIS)

    Fuertauer, Siegfried; Flandorfer, Hans; Effenberger, Herta S.

    2015-01-01

    The Sn rich ternary intermetallic compounds Li 3 Cu 6 Sn 4 (CSD-427097) and Li 2 CuSn 2 (CSD-427098) were synthesized from the pure elements by induction melting and annealing at 400 C. Structural investigations were performed by powder- and single-crystal XRD. Li 3 Cu 6 Sn 4 crystallizes in space group P6/mmm; it is structurally related to but not isotypic with MgFe 6 Ge 6 (a = 5.095(2) Aa, c = 9.524(3) Aa; wR 2 = 0.059; 239 unique F 2 -values, 17 free variables). Li 3 Cu 6 Sn 4 is characterized by two sites with a mixed Cu:Sn occupation. In contrast to all other Cu-Li-Sn compounds known so far, any mixed occupation was found for Cu-Li pairs only. In addition, one Li site is only half occupied. The second Sn rich phase is Li 2 CuSn 2 (space group I4 1 /amd, a = 4.4281(15) Aa, c = 19.416(4) Aa; wR 2 = 0.033; 213 unique F 2 -values, 12 atom free variables); it is the only phase in the Cu-Li-Sn system which is noted for full ordering. Both crystal structures exhibit 3D-networks which host Li atoms in channels. They are important for understanding the lithiation mechanism in Cu-Sn electrodes for Li-ion batteries.

  6. Robust Strategy for Crafting Li5Cr7Ti6O25@CeO2 Composites as High-Performance Anode Material for Lithium-Ion Battery.

    Science.gov (United States)

    Mei, Jie; Yi, Ting-Feng; Li, Xin-Yuan; Zhu, Yan-Rong; Xie, Ying; Zhang, Chao-Feng

    2017-07-19

    A facile strategy was developed to prepare Li 5 Cr 7 Ti 6 O 25 @CeO 2 composites as a high-performance anode material. X-ray diffraction (XRD) and Rietveld refinement results show that the CeO 2 coating does not alter the structure of Li 5 Cr 7 Ti 6 O 25 but increases the lattice parameter. Scanning electron microscopy (SEM) indicates that all samples have similar morphologies with a homogeneous particle distribution in the range of 100-500 nm. Energy-dispersive spectroscopy (EDS) mapping and high-resolution transmission electron microscopy (HRTEM) prove that CeO 2 layer successfully formed a coating layer on a surface of Li 5 Cr 7 Ti 6 O 25 particles and supplied a good conductive connection between the Li 5 Cr 7 Ti 6 O 25 particles. The electrochemical characterization reveals that Li 5 Cr 7 Ti 6 O 25 @CeO 2 (3 wt %) electrode shows the highest reversibility of the insertion and deinsertion behavior of Li ion, the smallest electrochemical polarization, the best lithium-ion mobility among all electrodes, and a better electrochemical activity than the pristine one. Therefore, Li 5 Cr 7 Ti 6 O 25 @CeO 2 (3 wt %) electrode indicates the highest delithiation and lithiation capacities at each rate. At 5 C charge-discharge rate, the pristine Li 5 Cr 7 Ti 6 O 25 only delivers an initial delithiation capacity of ∼94.7 mAh g -1 , and the delithiation capacity merely achieves 87.4 mAh g -1 even after 100 cycles. However, Li 5 Cr 7 Ti 6 O 25 @CeO 2 (3 wt %) delivers an initial delithiation capacity of 107.5 mAh·g -1 , and the delithiation capacity also reaches 100.5 mAh g -1 even after 100 cycles. The cerium dioxide modification is a direct and efficient approach to improve the delithiation and lithiation capacities and cycle property of Li 5 Cr 7 Ti 6 O 25 at large current densities.

  7. Decomposition reaction rate of BCl3-C3H6(propene)-H2 in the gas phase.

    Science.gov (United States)

    Xiao, Jun; Su, Kehe; Liu, Yan; Ren, Hongjiang; Zeng, Qingfeng; Cheng, Laifei; Zhang, Litong

    2012-07-05

    The decomposition reaction rate in the BCl(3)-C(3)H(6)-H(2) gas phase reaction system in preparing boron carbides was investigated based on the most favorable reaction pathways proposed by Jiang et al. [Theor. Chem. Accs. 2010, 127, 519] and Yang et al. [J. Theor. Comput. Chem. 2012, 11, 53]. The rate constants of all the elementary reactions were evaluated with the variational transition state theory. The vibrational frequencies for the stationary points as well as the selected points along the minimum energy paths (MEPs) were calculated with density functional theory at the B3PW91/6-311G(d,p) level and the energies were refined with the accurate model chemistry method G3(MP2). For the elementary reaction associated with a transition state, the MEP was obtained with the intrinsic reaction coordinates, while for the elementary reaction without transition state, the relaxed potential energy surface scan was employed to obtain the MEP. The rate constants were calculated for temperatures within 200-2000 K and fitted into three-parameter Arrhenius expressions. The reaction rates were investigated by using the COMSOL software to solve numerically the coupled differential rate equations. The results show that the reactions are, consistent with the experiments, appropriate at 1100-1500 K with the reaction time of 30 s for 1100 K, 1.5 s for 1200 K, 0.12 s for 1300 K, 0.011 s for 1400 K, or 0.001 s for 1500 K, for propene being almost completely consumed. The completely dissociated species, boron carbides C(3)B, C(2)B, and CB, have very low concentrations, and C(3)B is the main product at higher temperatures, while C(2)B is the main product at lower temperatures. For the reaction time 1 s, all these concentrations approach into a nearly constant. The maximum value (in mol/m(3)) is for the highest temperature 1500 K with the orders of -13, -17, and -23 for C(3)B, C(2)B, and CB, respectively. It was also found that the logarithm of the overall reaction rate and reciprocal

  8. Starting lithium prophylaxis early v. late in bipolar disorder

    DEFF Research Database (Denmark)

    Kessing, Lars Vedel; Vradi, Eleni; Andersen, Per Kragh

    2014-01-01

    BACKGROUND: No study has investigated when preventive treatment with lithium should be initiated in bipolar disorder. AIMS: To compare response rates among patients with bipolar disorder starting treatment with lithium early v. late. METHOD: Nationwide registers were used to identify all patients...... with a diagnosis of bipolar disorder in psychiatric hospital settings who were prescribed lithium during the period 1995-2012 in Denmark (n = 4714). Lithium responders were defined as patients who, following a stabilisation lithium start-up period of 6 months, continued lithium monotherapy without being admitted...... to hospital. Early v. late intervention was defined in two ways: (a) start of lithium following first contact; and (b) start of lithium following a diagnosis of a single manic/mixed episode. RESULTS: Regardless of the definition used, patients who started lithium early had significantly decreased rates of non...

  9. Chemical markup, XML, and the world wide web. 6. CMLReact, an XML vocabulary for chemical reactions.

    Science.gov (United States)

    Holliday, Gemma L; Murray-Rust, Peter; Rzepa, Henry S

    2006-01-01

    A set of components (CMLReact) for managing chemical and biochemical reactions has been added to CML. These can be combined to support most of the strategies for the formal representation of reactions. The elements, attributes, and types are formally defined as XMLSchema components, and their semantics are developed. New syntax and semantics in CML are reported and illustrated with 10 examples.

  10. Grain Boundary Engineering of Lithium-Ion-Conducting Lithium Lanthanum Titanate for Lithium-Air Batteries

    Science.gov (United States)

    2016-01-01

    Titanate for Lithium-Air Batteries by Victoria L Blair, Claire V Weiss Brennan, and Joseph M Marsico Approved for public...Air Batteries by Victoria L Blair and Claire V Weiss Brennan Weapons and Materials Research Directorate, ARL Joseph M Marsico Rochester...Titanate for Lithium-Air Batteries 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Victoria L Blair, Claire V

  11. Lithium ion behavior in lithium oxide by neutron scattering studies

    International Nuclear Information System (INIS)

    Ishii, Yoshinobu; Morii, Yukio; Katano, Susumu; Watanabe, Hitoshi; Funahashi, Satoru; Ohno, Hideo; Nicklow, R.M.

    1992-01-01

    Lithium ion behavior in lithium oxide, Li 2 O, was studied in the temperature range from 293 K to 1120 K by the High-Resolution Powder Diffractometer (HRPD) installed in the JRR-3M. The diffraction patterns were analyzed with the RIETAN program. At room temperature, the thermal parameters related to the mean square of the amplitude of vibration of the lithium and the oxygen ions were 6 x 10 -21 m 2 and 4 x 10 -21 m 2 , respectively. AT 1120 K the thermal parameter of the lithium ion was 34 x 10 -21 m 2 . On the other hand, the parameter of the oxygen ion was 16 x 10 -21 m 2 . Inelastic neutron scattering studies for the lithium oxide single crystal were also carried out on the triple-axis neutron spectrometers installed at the JRR-2 and the HFIR. Although the value of a phonon energy of a transverse acoustic mode (Σ 3 ) at zone boundary was 30.6 meV at room temperature, this value was decreased to 25.1 meV at 700 K. This large softening was caused by anharmonicity of the crystal potential of lithium oxide. (author)

  12. One-pot in situ redox synthesis of hexacyanoferrate/conductive polymer hybrids as lithium-ion battery cathodes.

    Science.gov (United States)

    Wong, Min Hao; Zhang, Zixuan; Yang, Xianfeng; Chen, Xiaojun; Ying, Jackie Y

    2015-09-14

    An efficient and adaptable method is demonstrated for the synthesis of lithium hexacyanoferrate/conductive polymer hybrids for Li-ion battery cathodes. The hybrids were synthesized via a one-pot method, involving a redox-coupled reaction between pyrrole monomers and the Li3Fe(CN)6 precursor. The hybrids showed much better cyclability relative to reported Prussian Blue (PB) analogs.

  13. Intramolecular anionic diels-alder reactions of 1-aryl-4-oxahepta-1,6-diyne systems in DMSO.

    Science.gov (United States)

    Kudoh, Takayuki; Mori, Tomoko; Shirahama, Mitsuhito; Yamada, Masashi; Ishikawa, Teruhiko; Saito, Seiki; Kobayashi, Hisayoshi

    2007-04-25

    Base-promoted cycloaddition reactions of 1-aryl- or 1-aryl-7-substituted-4-oxahepta-1,6-diyne systems in DMSO have proven to involve an anionic intramolecular Diels-Alder process taking place even at room temperature in spite of the reaction suffering from temporary disruption of aromaticity. Although initially formed alpha-arylallenide anion can be protonated by DMSO, it can be back to the allenide anion probably because of a small acidity difference between alpha-arylallene and DMSO. The alpha-arylallenide anion in combination with the alpha-aryl substituent can constitute an anionic diene structure that undergoes the intramolecular Diels-Alder reaction involving the C(6)-yne part, a very fast process probably because of the increased HOMO-1 level of the anionic diene, as shown by DFT calculations. Diversified substituted naphthalenes, benzofurans, phenanthrenes, and quinolines, including biaryl architectures, are available from 4-oxahepta-1,6-diynes in a highly expeditious way.

  14. Synthesis and thermal stability of the sodalite Na6Zn2[Al6Si6O24](SO4)2 and its reaction with hydrogen

    DEFF Research Database (Denmark)

    Heiden, Frank; Nielsen, Ulla Gro; Warner, Terence Edwin

    2012-01-01

    Ca2[Al6Si6O24](SO4)2. Na6Zn2[Al6Si6O24](SO4)2 was shown to be largely immiscible with nosean, Na8[Al6Si6O24]SO4 in the solid-state. Na6Zn2[Al6Si6O24](SO4)2 decomposes above 700 °C, yielding nosean, Na8[Al6Si6O24]SO4; willemite, Zn2SiO4; gahnite, ZnAl2O4; and presumably a glass phase, 2Na2O•9SiO2...

  15. Effects of neostriatal 6-OHDA lesion on performance in a rat sequential reaction time task.

    Science.gov (United States)

    Domenger, D; Schwarting, R K W

    2008-10-31

    Work in humans and monkeys has provided evidence that the basal ganglia, and the neurotransmitter dopamine therein, play an important role for sequential learning and performance. Compared to primates, experimental work in rodents is rather sparse, largely due to the fact that tasks comparable to the human ones, especially serial reaction time tasks (SRTT), had been lacking until recently. We have developed a rat model of the SRTT, which allows to study neural correlates of sequential performance and motor sequence execution. Here, we report the effects of dopaminergic neostriatal lesions, performed using bilateral 6-hydroxydopamine injections, on performance of well-trained rats tested in our SRTT. Sequential behavior was measured in two ways: for one, the effects of small violations of otherwise well trained sequences were examined as a measure of attention and automation. Secondly, sequential versus random performance was compared as a measure of sequential learning. Neurochemically, the lesions led to sub-total dopamine depletions in the neostriatum, which ranged around 60% in the lateral, and around 40% in the medial neostriatum. These lesions led to a general instrumental impairment in terms of reduced speed (response latencies) and response rate, and these deficits were correlated with the degree of striatal dopamine loss. Furthermore, the violation test indicated that the lesion group conducted less automated responses. The comparison of random versus sequential responding showed that the lesion group did not retain its superior sequential performance in terms of speed, whereas they did in terms of accuracy. Also, rats with lesions did not improve further in overall performance as compared to pre-lesion values, whereas controls did. These results support previous results that neostriatal dopamine is involved in instrumental behaviour in general. Also, these lesions are not sufficient to completely abolish sequential performance, at least when acquired

  16. Lithium isotopic separation: preliminary studies

    International Nuclear Information System (INIS)

    Macedo, Sandra Helena Goulart de

    1998-01-01

    In order to get the separation of natural isotopes of lithium by electrolytic amalgamation, an electrolytic cell with a confined mercury cathode was used to obtain data for the design of a separation stage. The initial work was followed by the design of a moving mercury cathode electrolytic cell and three experiments with six batches stages were performed for the determination of the elementary separation factor. The value obtained, 1.053, was ill agreement: with the specialized literature. It was verified in all experiments that the lithium - 6 isotope concentrated in the amalgam phase and that the lithium - 7 isotope concentrated in the aqueous phase. A stainless-steel cathode for the decomposition of the lithium amalgam and the selective desamalgamation were also studied. In view of the results obtained, a five stages continuous scheme was proposed. (author)

  17. Does lithium protect against dementia?

    DEFF Research Database (Denmark)

    Kessing, Lars Vedel; Forman, Julie Lyng; Andersen, Per Kragh

    2010-01-01

    OBJECTIVE: To investigate whether treatment with lithium in patients with mania or bipolar disorder is associated with a decreased rate of subsequent dementia. METHODS: Linkage of register data on prescribed lithium in all patients discharged from psychiatric health care service with a diagnosis...... exposed to lithium (50.4%), 1,781 to anticonvulsants (36.7%), 4,280 to antidepressants (88.1%), and 3,901 to antipsychotics (80.3%) during the study period. A total of 216 patients received a diagnosis of dementia during follow-up (103.6/10,000 person-years). During the period following the second...... prescription of lithium, the rate of dementia was decreased compared to the period following the first prescription. In contrast, the rates of dementia during multiple prescription periods with anticonvulsants, antidepressants, or antipsychotics, respectively, were not significantly decreased compared...

  18. Lithium salts for advanced lithium batteries: Li–metal, Li–O2, and Li–S

    DEFF Research Database (Denmark)

    Younesi, Reza; Veith, Gabriel M.; Johansson, Patrik

    2015-01-01

    Presently lithium hexafluorophosphate (LiPF6) is the dominant Li-salt used in commercial rechargeable lithium-ion batteries (LIBs) based on a graphite anode and a 3–4 V cathode material. While LiPF6 is not the ideal Li-salt for every important electrolyte property, it has a uniquely suitable...... combination of properties (temperature range, passivation, conductivity, etc.) rendering it the overall best Li-salt for LIBs. However, this may not necessarily be true for other types of Li-based batteries. Indeed, next generation batteries, for example lithium–metal (Li–metal), lithium–oxygen (Li–O2......), and lithium–sulfur (Li–S), require a re-evaluation of Li-salts due to the different electrochemical and chemical reactions and conditions within such cells. This review explores the critical role Li-salts play in ensuring in these batteries viability....

  19. The development of a chemical kinetic measurement apparatus and the determination of the reaction rate constants for lithium-lead/steam interaction. Final report 9-21-90--3-31-95

    International Nuclear Information System (INIS)

    Biney, P.O.

    1995-03-01

    The objective of this research to experimentally determine the hydrogen generation rate during the beginning and subsequent stages of liquid metal (Li 17 Pb 83 ) and water reaction. The experimental set-up has been built. It includes a metal sample preparation apparatus, a reaction system, a measurement system and a PC based data acquisition and control system. The most important feature of the reaction system is a pneumatic actuated quick opening and closing high temperature, all stainless steel valve used the system for reaction time control. The PC system provides remote process sequencing, acquisition and control of all the systems except the metal preparation apparatus. Due to the reactivity of the lithium, all the metal sampling, preparation and loading procedures are executed in a glove box under argon protection. The metal temperature was varied between 350 degrees C-650 degrees C and water temperature fixed at 60 degrees C during the experiments. A set of experimental procedures and two analyses methods: (1) thermodynamics method and (2) heat transfer method are discussed. All the measurements and data collections are executed under the PC system control. A data analysis program is used to calculate both the partial pressure of hydrogen and the hydrogen generation rate. The experiment results indicate that the amount of hydrogen generated is relate to the initial liquid metal temperature when the reaction surface is fixed. The mass of hydrogen generated as a function of initial liquid metal temperature and time of reaction is presented, The hydrogen generation over a time period of 240 seconds and the calculated errors are summarized in Table 1

  20. First direct measurement of the 2H(α,γ)6Li cross section at big bang energies and the primordial lithium problem.

    Science.gov (United States)

    Anders, M; Trezzi, D; Menegazzo, R; Aliotta, M; Bellini, A; Bemmerer, D; Broggini, C; Caciolli, A; Corvisiero, P; Costantini, H; Davinson, T; Elekes, Z; Erhard, M; Formicola, A; Fülöp, Zs; Gervino, G; Guglielmetti, A; Gustavino, C; Gyürky, Gy; Junker, M; Lemut, A; Marta, M; Mazzocchi, C; Prati, P; Rossi Alvarez, C; Scott, D A; Somorjai, E; Straniero, O; Szücs, T

    2014-07-25

    Recent observations of (6)Li in metal poor stars suggest a large production of this isotope during big bang nucleosynthesis (BBN). In standard BBN calculations, the (2)H(α,γ)(6)Li reaction dominates (6)Li production. This reaction has never been measured inside the BBN energy region because its cross section drops exponentially at low energy and because the electric dipole transition is strongly suppressed for the isoscalar particles (2)H and α at energies below the Coulomb barrier. Indirect measurements using the Coulomb dissociation of (6)Li only give upper limits owing to the dominance of nuclear breakup processes. Here, we report on the results of the first measurement of the (2)H(α,γ)(6)Li cross section at big bang energies. The experiment was performed deep underground at the LUNA 400 kV accelerator in Gran Sasso, Italy. The primordial (6)Li/(7)Li isotopic abundance ratio has been determined to be (1.5 ± 0.3) × 10(-5), from our experimental data and standard BBN theory. The much higher (6)Li/(7)Li values reported for halo stars will likely require a nonstandard physics explanation, as discussed in the literature.

  1. Lithium ferrite: The study on magnetic and complex permittivity characteristics

    Directory of Open Access Journals (Sweden)

    Madhavaprasad Dasari

    2017-03-01

    Full Text Available Lithium ferrite (Li0.5Fe2.5O4 powder was prepared by solid state reaction method, which was finally pressed and sintered at 1150 °C. The spinel structure of the lithium ferrite was confirmed by X-ray diffraction and grain size estimation was obtained from scanning electron microscope (SEM. Fourier transform infrared spectroscopy (FTIR confirmed the presence of primary and secondary absorption bands characteristic for spinel structure. The force constants were estimated using absorption bands for the lithium ferrite. Magnetization and dielectric studies were carried out for the sintered sample. Saturation magnetization (Ms of 59.6 emu/g was achieved and variation of magnetization with temperature was used to identify the Curie temperature. The complex permittivity (ε∗ for the lithium ferrite sample was obtained for wide frequency range up to 3 GHz and discussed based on available models. The Curie temperature was estimated around 480 °C and verified from both magnetization versus temperature and dielectric constant versus temperature measurements.

  2. Lithium Insertion in LixMn2O4, 0

    DEFF Research Database (Denmark)

    West, Keld; Zachau-Christiansen, Birgit; Skaarup, Steen

    1996-01-01

    The electrochemical lithium insertion properties of highly crystalline LixMn2O4 are investigated in the approximate lithium insertion range 0 ... of the lithium insertion/extraction reactions is better at the higher voltages (versus Li/Li+), and particularly at the 4 V plateau. The lithium insertion/extraction reaction at the 1 V plateau although essentially reversible is associated with a significant voltage hysteresis....

  3. Cross sections of nuclear reactions induced by protons, deuterons, and alpha particles. Pt.6. Phosphorus

    International Nuclear Information System (INIS)

    Tobailem, Jacques.

    1981-11-01

    Cross sections are reviewed for nuclear reactions induced by protons, deuterons, and alpha particles on phosphorus targets. When necessary, published experimental data are corrected, and, when possible, excitation functions are proposed [fr

  4. Lithium-rich very metal-poor stars discovered with LAMOST and Subaru

    Science.gov (United States)

    Aoki, Wako; Li, Haining; Matsuno, Tadafumi; Kumar, Yerra Bharat; Shi, Jianrong; Suda, Takuma; Zhao, Gang

    2018-04-01

    Lithium is a unique element that is produced in the Big Bang nucleosynthesis but is destroyed by nuclear reactions inside stars. As a result, almost constant lithium abundance is found in unevolved main-sequence metal-poor stars, although the value is systematically lower than that expected from the standard Big Bang nucleosynthesis models, whereas lithium abundances of red giants are more than one order of magnitudes lower than those of unevolved stars. There are, however, a small fraction of metal-poor stars that show extremely high lithium abundances, which is not explained by standard stellar evolution models. We have discovered 12 new very metal-poor stars that have enhancement of lithium by more than 10 times compared with typical metal-poor stars at similar evolutionary stages by the large-scale spectroscopic survey with LAMOST and the follow-up high-resolution spectroscopy with the Subaru Telescope. The sample shows a wide distribution of evolutionary stages from subgiants to red giants with the metallicity of -3.3 <[Fe/H]< -1.6. The chemical abundance ratios of other elements have been obtained by our spectroscopic study, and an estimate of the binary frequency by radial velocity monitoring is ongoing. The observational results provide new constraints on the scenarios to explain lithium-rich metal-poor stars, such as extra mixing during the evolution along the red giant branch, mass-transfer from a companion AGB star, and engulfment of planet-like objects. These explanations are very unlikely for at least some of lithium-rich objects in our sample, suggesting a new mechanism that enhances lithium during the low-mass star evolution.

  5. Synthesis and properties of new carboxyborate lithium salts as electrolytes for lithium-ion batteries

    International Nuclear Information System (INIS)

    Gładka, Dorota; Krajewski, Mariusz; Młynarska, Sandra; Galińska, Justyna; Zygadło-Monikowska, Ewa

    2017-01-01

    Bis(carboxytrifluoroborate lithium) salts [R(CH 2 COOBF 3 Li) 2 ] with oxyethylene groups R of oligomeric molar masses [R = O(CH 2 CH 2 O) n , where n = 3 or 11, BCB3 and BCB11, respectively] were synthesized via reaction of carboxylates salts with boron fluoride. The new salts were characterized by spectroscopic analysis. The physical properties of the salts were determined by oxyethylene chain length. For n = 3 the salt was crystalline with m p = 197 °C and for n = 11 it showed properties of an ionic liquid at ambient temperature. Their thermal stability was at least 250 °C. The values of lithium-ion transference numbers (T + ) of the solutions in polar aprotic solvents, determined by a well established steady-state technique, were in the range of 0.2–0.6. Electrochemical impedance spectroscopy analysis of solid polymer electrolytes (SPEs) based on PEO and studied salts with different concentration (from 24 to 94 wt %) was carried out. The ionic conductivity of SPEs was in the order of 10 −8 –10 −7 S cm −1 at room temperature and 10 −4 S cm −1 at 80 °C. A distinguishing feature of SPEs with the studied new salts is the high immobilization of anions, which causes almost a monoconducting character of charge transport. Lithium transference numbers (T + ) exceed 0.9.

  6. Size effects in lithium ion batteries

    International Nuclear Information System (INIS)

    Yao Hu-Rong; Yin Ya-Xia; Guo Yu-Gao

    2016-01-01

    Size-related properties of novel lithium battery materials, arising from kinetics, thermodynamics, and newly discovered lithium storage mechanisms, are reviewed. Complementary experimental and computational investigations of the use of the size effects to modify electrodes and electrolytes for lithium ion batteries are enumerated and discussed together. Size differences in the materials in lithium ion batteries lead to a variety of exciting phenomena. Smaller-particle materials with highly connective interfaces and reduced diffusion paths exhibit higher rate performance than the corresponding bulk materials. The thermodynamics is also changed by the higher surface energy of smaller particles, affecting, for example, secondary surface reactions, lattice parameter, voltage, and the phase transformation mechanism. Newly discovered lithium storage mechanisms that result in superior storage capacity are also briefly highlighted. (topical review)

  7. Properties of lithium and its handling

    International Nuclear Information System (INIS)

    Asada, Takashi; Kano, Shigeki; Tachi, Toshiaki; Kawai, Masataka

    2000-09-01

    Lithium is one of good coolants because of high boiling point (1317degC), small specific gravity (0.47 at 600degC) and large specific heat (1 cal/g/degC). Therefore if lithium will be used in fast reactor for coolant, the heat efficiency of reactor will largely increase. Here the fundamental properties of lithium and the results of examination on chemical reaction, combustion and extinction are shown. These examinations were also carried out on sodium to compare with lithium. The differences between both are that lithium reacts more moderately with water, not explosive, and is not combustible but after ignition burns at higher temperature and longer. (author)

  8. Electrochemical reaction mechanisms under various charge-discharge operating conditions for Li1.2Ni0.13Mn0.54Co0.13O2 in a lithium-ion battery

    Science.gov (United States)

    Konishi, Hiroaki; Hirano, Tatsumi; Takamatsu, Daiko; Gunji, Akira; Feng, Xiaoliang; Furutsuki, Sho; Okumura, Takefumi; Terada, Shohei; Tamura, Kazuhisa

    2018-06-01

    The potential in each state of charge (SOC) during charging of Li1.2Ni0.13Mn0.54Co0.13O2 is higher than that during discharging. In other words, the potential hysteresis occurs between charging and discharging. Furthermore, the potential in each SOC changes according to the charge-discharge operating conditions, indicating that the charge-discharge reaction mechanism is also affected. To clarify the effect of charge-discharge operating conditions on the electrochemical reaction, Li1.2Ni0.13Mn0.54Co0.13O2 was charged and discharged under various charge-discharge operating ranges, and open-circuit potential (OCP), crystal structure, and oxidation states of the transition metals were evaluated by electrochemical measurement, X-ray diffraction (XRD), and X-ray absorption fine structure (XAFS). These results indicate that OCP, lattice parameters, and oxidation states of the transition metals of Li1.2Ni0.13Mn0.54Co0.13O2 in each SOC are not constant. The XRD results indicate that two phases, namely, LiNi0.33Mn0.33Co0.33O2-like and Li2MnO3-like, exist in Li1.2Ni0.13Mn0.54Co0.13O2. For the LiNi0.33Mn0.33Co0.33O2-like phase, the relationship between OCP, lattice parameters, and oxidation states of the transition metals in each SOC is not affected by the charge-discharge operating conditions, indicating that extraction and insertion of lithium ions for the LiNi0.33Mn0.33Co0.33O2-like phase progresses at almost the same potential. Although the extraction and insertion of lithium ions for the Li2MnO3-like phase progresses at almost the same potential in the low-SOC region, the OCP and lattice parameter in each SOC in the high-SOC region are not constant. Therefore, the extraction of lithium ions from the Li2MnO3-like phase in the high-SOC region causes the potential hysteresis of Li1.2Ni0.13Mn0.54Co0.13O2.

  9. Kinetic and thermodynamic study of the reaction catalyzed by glucose-6-phosphate dehydrogenase with nicotinamide adenine dinucleotide

    International Nuclear Information System (INIS)

    Martin del Campo, Julia S.; Patino, Rodrigo

    2011-01-01

    Research highlights: → The reaction catalyzed by one enzyme of the pentose phosphate pathway was studied. → A spectrophotometric method is proposed for kinetic and thermodynamic analysis. → The pH and the temperature influences are reported on physical chemical properties. → Relative concentrations of substrates are also important in the catalytic process. - Abstract: The enzyme glucose-6-phosphate dehydrogenase (G6PD, EC 1.1.1.49) from Leuconostoc mesenteroides has a dual coenzyme specificity with oxidized nicotinamide adenine dinucleotide (NAD ox ) and oxidized nicotinamide adenine dinucleotide phosphate as electron acceptors. The G6PD coenzyme selection is determined by the metabolic cellular prevailing conditions. In this study a kinetic and thermodynamic analysis is presented for the reaction catalyzed by G6PD from L. mesenteroides with NAD ox as coenzyme in phosphate buffer. For this work, an in situ spectrophotometric technique was employed based on the detection of one product of the reaction. Substrate and coenzyme concentrations as well as temperature and pH effects were evaluated. The apparent equilibrium constant, the Michaelis constant, and the turnover number were determined as a function of each experimental condition. The standard transformed Gibbs energy of reaction was determined from equilibrium constants at different initial conditions. For the product 6-phospho-D-glucono-1,5-lactone, a value of the standard Gibbs energy of formation is proposed, Δ f G o = -1784 ± 5 kJ mol -1 .

  10. Kinetic and thermodynamic study of the reaction catalyzed by glucose-6-phosphate dehydrogenase with nicotinamide adenine dinucleotide

    Energy Technology Data Exchange (ETDEWEB)

    Martin del Campo, Julia S. [Departamento de Fisica Aplicada, Centro de Investigacion y de Estudios Avanzados - Unidad Merida, Carretera antigua a Progreso Km. 6, A.P. 73 Cordemex, 97310, Merida, Yucatan (Mexico); Patino, Rodrigo, E-mail: rtarkus@mda.cinvestav.mx [Departamento de Fisica Aplicada, Centro de Investigacion y de Estudios Avanzados - Unidad Merida, Carretera antigua a Progreso Km. 6, A.P. 73 Cordemex, 97310, Merida, Yucatan (Mexico)

    2011-04-20

    Research highlights: {yields} The reaction catalyzed by one enzyme of the pentose phosphate pathway was studied. {yields} A spectrophotometric method is proposed for kinetic and thermodynamic analysis. {yields} The pH and the temperature influences are reported on physical chemical properties. {yields} Relative concentrations of substrates are also important in the catalytic process. - Abstract: The enzyme glucose-6-phosphate dehydrogenase (G6PD, EC 1.1.1.49) from Leuconostoc mesenteroides has a dual coenzyme specificity with oxidized nicotinamide adenine dinucleotide (NAD{sub ox}) and oxidized nicotinamide adenine dinucleotide phosphate as electron acceptors. The G6PD coenzyme selection is determined by the metabolic cellular prevailing conditions. In this study a kinetic and thermodynamic analysis is presented for the reaction catalyzed by G6PD from L. mesenteroides with NAD{sub ox} as coenzyme in phosphate buffer. For this work, an in situ spectrophotometric technique was employed based on the detection of one product of the reaction. Substrate and coenzyme concentrations as well as temperature and pH effects were evaluated. The apparent equilibrium constant, the Michaelis constant, and the turnover number were determined as a function of each experimental condition. The standard transformed Gibbs energy of reaction was determined from equilibrium constants at different initial conditions. For the product 6-phospho-D-glucono-1,5-lactone, a value of the standard Gibbs energy of formation is proposed, {Delta}{sub f}G{sup o} = -1784 {+-} 5 kJ mol{sup -1}.

  11. Onium ions. XVI. Hydrogen--deuterium exchange accompanying the cleavage of ammonium (tetradeuterioammonium) trifluoroacetate by lithium deuteride (hydride) indicating Sn2 like nucleophilic displacement at quaternary nitrogen through pentacoordinated NH5

    International Nuclear Information System (INIS)

    Olah, G.A.; Donovan, D.J.; Shen, J.; Klopman, G.

    1975-01-01

    The reactions of ammonium trifluoroacetate and lithium hydride, of ammonium trifluoroacetate and lithium deuteride, and of tetradeuteroammonium trifluoroacetate and lithium hydride were studied in an attempt to prove experimentally nucleophilic displacement through the formation of pentacoordinated NH 5 . Significant isotopic scramblings were observed in the reaction products. An analysis of possible side reactions indicated that the most reasonable explanation for the reaction products obtained is the attack of D - on the quarternary hydrogen of NH 4 + in an SN2-like fashion causing exchange to occur via pentacoordinated NH 4 D. The possibility of a real pentacoordinated intermediate was also considered. CNDO/2 calculations show that a nucleophilic attack on hydrogen is favored, but the alternative attack on nitrogen can not be dismissed because of the experimental data. The reaction of NF 4 + SbF 6 - and LiF could indicate the possibility of nucleophilic attack on nitrogen. (U.S.)

  12. Theoretical investigation of molecular hydrogen reactions with active centres in B6H5- and AlB6H5- clusters

    International Nuclear Information System (INIS)

    Mebel', A.M.; Charkin, O.P.

    1991-01-01

    Nonempirical calculations of sections of potential surface (PS) along the shortest way of reaction of hydrogen interaction with different active centres in AlB 5 H 5 - cluster were conducted. Mechanisms of reactions of valent-saturated hydrides (BH, AlH) and clusters (B 6 H 5 - , AlB 5 H 5 - ) with molecular hydrogen are correlated. Qualitative model enabling to form an opinion about the presence or the absence of barrier on PS of the shortest way of reactions of breaking σ-bond of H-H type on the active centre of cluster, is suggested. The model is based on analysis of the character of canonical MO reagents and products

  13. Current status of the technology development on lithium safety handling under IFMIF/EVEDA

    Energy Technology Data Exchange (ETDEWEB)

    Furukawa, Tomohiro, E-mail: furukawa.tomohiro@jaea.go.jp; Hirakawa, Yasushi; Kato, Shoichi; Iijima, Minoru; Ohtaka, Masahiko; Kondo, Hiroo; Kanemura, Takuji; Wakai, Eiichi

    2014-12-15

    Studies for establishing technology for the safe handling of lithium was performed in the Engineering Validation and Engineering Design Activities (EVEDA) for the International Fusion Material Irradiation Facility (IFMIF). This research comprises four tasks: (a) extinguishing lithium files, (b) chemical reactions of lithium on the event of a leak, (c) lithium removal from the components, and (d) chemical analysis of impurities in lithium. Tasks (a) and (b), related to functions on the event of a lithium leak, involve selection of the material suitable for extinguishing lithium fires and assessment of corrosive effects of leaked lithium on materials at high temperature, respectively. Task (c) involves evaluation of methods for the replacement and/or decommissioning of the lithium components. Task (d) constitutes the development of high-precision techniques for the determination of impurities in lithium, particularly the dominating corrosive impurity—dissolved nitrogen. Experimental results addressing the objectives of each of the tasks are described in this communication.

  14. (6Li,d) reaction on sd-, fp- and g-shell nuclei in ZR- and FR-DWBA formalisms

    International Nuclear Information System (INIS)

    Rahman, M.A.; Mecking, M.; Strohbusch, U.

    1991-06-01

    ( 6 Li,d) reaction angular distributions on target nuclei 16 ≤ A ≤ 90 have been analyzed using both ZR- and FR-DWBA formalisms. The most prevalent method of analysis of alpha-transfer reactions such as( 6 Li,d) and its reverse (d, 6 Li) (where the wave function at zero distance in the p-state of relative cluster motion in the A = 6 nuclei will not have node) is the ZR-DWBA calculations due to the relatively short time of computation. It is of particular interest to verify whether FR-DWBA calculations result in similar S α - values to those of ZR-DWBA or not. It is found that to derive similar S α -values as in FR-DWBA calculations, one requires relatively large real well depth in ZR-DWBA calculations. Qualitative discussions have been made in this direction. (author). 12 refs, 3 figs, 2 tabs

  15. The 6th Grade Primary History Book and the Reactions of the Greek and Cypriot Educational Communities and Societies

    Science.gov (United States)

    Kimitris, Petros N.

    2017-01-01

    The present study was designed to explore the role of Rebousi et al's primary 6th grade history school book in evaluating the experience of a nation but also to examine the causes behind the reactions of political parties, historians and the wider public. History books and politics have very deep roots that reflect on old responsibilities,…

  16. Possible production of glueballs in anti p 4He reactions at 0.6 GeVc-1 incident momentum

    International Nuclear Information System (INIS)

    Balestra, F.; Bossolasco, S.; Bussa, M.P.; Busso, L.; Fava, L.; Ferrero, L.; Grasso, A.; Maggiora, A.; Panzieri, D.; Piragino, G.; Piragino, R.; Tosello, F.; Bendiscioli, G.; Filippini, V.; Rotondi, A.; Salvini, P.; Zenoni, A.; Batusov, Yu.; Bunyatov, S.A.; Falomkin, I.V.; Nichitiu, F.; Pontecorvo, G.B.; Rozhdestvensky, A.M.; Sapozhnikov, M.G.; Tretyak, V.I.; Guaraldo, C.; Lodi Rizzini, E.; Haatuft, A.; Halsteinslid, A.; Myklebost, K.; Olsen, J.M.; Breivik, F.O.; Danielsen, K.M.; Jacobsen, T.; Soerensen, S.O.

    1991-01-01

    A sharp peak at 1150 MeV c -2 in the π - π + π - π + -system in the final state of anti p 4 He-reactions at 0.6 GeV c -1 incident momentum is seen. This system probably has spin-parity = 0 + or 2 + , which are possible spin-parity assignments of a glueball. (orig.)

  17. Charged particle spectra in oxygen-induced reactions at 14. 6 and 60 GeV/Nucleon

    Energy Technology Data Exchange (ETDEWEB)

    Adamovich, M I; Aggarwal, M M; Arora, R; Alexandrov, Y A; Azimov, S A; Badyal, S K; Basova, E; Bhalla, K B; Bahsin, A; Bhatia, V S; Bomdarenko, R A; Burnett, T H; Cai, X; Chernova, L P; Chernyavski, M M; Dressel, B; Friedlander, E M; Gadzhieva, S I; Ganssauge, E R; Garpman, S; Gerassimov, S G; Gill, A; Grote, J; Gulamov, K G; Gulyamov, V G; Gupta, V K; Hackel, S; Heckman, H H; Jakobsson, B; Judek, B; Katroo, S; Kadyrov, F G; Kallies, H; Karlsson, L; Kaul, G L; Kaur, M; Kharlamov, S P; Kohli, J; Kumar, V; Lal, P; Larionova, V G; Lindstrom, P J; Liu, L S; Lokanathan, S; Lord, J; Lukicheva, N S; Mangotra, L K; Maslennikova, N V; Mitta, I S; Monnand, E; Mookerjee, S; Mueller, C; Nasyrov, S H; Nvtny, V S; Orlova, G I; Otterlund, I; Peresadko, N G; Persson, S; Petrov, N V; Qian, W Y; Raniwala, R; Raniwala, S; Rao, N K; Rhee, J Y; Shaidkhanov, N; Salmanova, N G; Schulz, W; Schussler, F; Shukla, V S; Skelding, D; Soederstroe,

    1989-10-01

    Multiplicity distributions and pseudo-rapidity distributions of charged particles from oxygen-induced nuclear reactions at 14.6 and 60 GeV/nucleon are presented. The data were taken from the EMU{minus}01 emulsion stacks and compared to simulations from the Lund Monte Carlo Model (FRITIOF).

  18. Study of reaction mechanisms in 40Ar+68Zn interaction at 14.6 and 27.6 MeV/N

    International Nuclear Information System (INIS)

    Rami, F.

    1985-01-01

    The competing mechanisms in the 40 Ar+ 68 Zn reaction have been investigated at two bombarding energies: 14.6 and 27.6 MeV/nucleon. Mass, charge and energy spectra of the reaction products have been measured in a large angular range (3 0 0 ). The results show that important changes occur in this energy region. At 14.6 MeV/nucleon the production of the projectile-like fragments results mainly from deep inelastic and direct nucleon transfer reactions; while at 27.6 MeV/nucleon a strong component corresponding to process similar to projectile fragmentation is also observed. A distinction between the fragmentation process and direct transfer of few nucleons has been possible by analysing the linear momentum distributions of the detected fragments. The energy dependance of the fusion cross section indicates that this process should disappear for incident energies E/A > approximately 30 MeV/nucleon. The maximum temperature reached by the compound nucleus has been deduced i.e. Tmax approximately equal 7 MeV; this value is in agreement with recent theoretical predictions [fr

  19. Lithium Oxysilicate Compounds Final Report.

    Energy Technology Data Exchange (ETDEWEB)

    Apblett, Christopher A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Coyle, Jaclyn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-09-01

    In this study, the structure and composition of lithium silicate thin films deposited by RF magnetron co-sputtering is investigated. Five compositions ranging from Li2Si2O5 to Li8SiO6 were confirmed by inductively coupled plasma-optical emission spectroscopy (ICP-OES) and structure analysis on the evolution of non-bridging oxygens in the thin films was conducted with fourier transform infrared (FTIR) spectroscopy. It was found that non-bridging oxygens (NBOs) increased as the silicate network breaks apart with increasing lithium content which agrees with previous studies on lithium silicates. Thin film impurities were examined with x-ray photoelectron spectroscopy (XPS) and time of flight secondary ion mass spectroscopy (TOFSIMS) and traced back to target synthesis. This study utilizes a unique synthesis technique for lithium silicate thin films and can be referred to in future studies on the ionic conductivity of lithium silicates formed on the surface of silicon anodes in lithium ion batteries.

  20. Modifications made to the MELCOR Code for Analyzing Lithium Fires in Fusion Reactors

    International Nuclear Information System (INIS)

    Merrill, B.J.

    2000-01-01

    This report documents initial modifications made to the MELCOR code that allows MELCOR to predict the consequences of lithium spill accidents for evolving fusion reactor designs. These modifications include thermodynamic and transport properties for lithium, and physical models for predicting the rate of reaction of and energy production from the lithium-air reaction. A benchmarking study was performed with this new MELCOR capability. Two lithium-air reaction tests conducted at the Hanford Engineering Development Laboratory (HEDL) were selected for this benchmark study. Excellent agreement was achieved between MELCOR predictions and measured data. Recommendations for modeling lithium fires with MELCOR and for future work in this area are included in this report

  1. Atomic lithium vapor laser isotope separation

    CERN Document Server

    Olivares, I E

    2002-01-01

    An atomic vapor laser isotope separation in lithium was performed using tunable diode lasers. The method permits also the separation of the isotopes between the sup 6 LiD sub 2 and the sup 7 LiD sub 1 lines using a self-made mass separator which includes a magnetic sector and an ion beam designed for lithium. (Author)

  2. Atomic lithium vapor laser isotope separation

    International Nuclear Information System (INIS)

    Olivares, I.E.; Rojas, C.

    2002-01-01

    An atomic vapor laser isotope separation in lithium was performed using tunable diode lasers. The method permits also the separation of the isotopes between the 6 LiD 2 and the 7 LiD 1 lines using a self-made mass separator which includes a magnetic sector and an ion beam designed for lithium. (Author)

  3. Synthesis of Lithium Fluoride from Spent Lithium Ion Batteries

    Directory of Open Access Journals (Sweden)

    Daniela S. Suarez

    2017-05-01

    Full Text Available Lithium (Li is considered a strategic element whose use has significantly expanded. Its current high demand is due to its use in lithium ion batteries for portable electronic devices, whose manufacture and market are extensively growing every day. These days there is a great concern about the final disposal of these batteries. Therefore, the possibility of developing new methodologies to recycle their components is of great importance, both commercially and environmentally. This paper presents results regarding important operational variables for the dissolution of the lithium and cobalt mixed-oxide (LiCoO2 cathodes from spent lithium ion batteries (LIBs with hydrofluoric acid. The recovery and synthesis of Co and Li compounds were also investigated. The dissolution parameters studied were: temperature, reaction time, solid-liquid ratio, stirring speed, and concentration of HF. The investigated recovery parameters included: pH, temperature, and time with and without stirring. The final precipitation of lithium fluoride was also examined. The results indicate that an increase in the HF concentration, temperature, and reaction time favors the leaching reaction of the LiCoO2. Dissolutions were close to 60%, at 75 °C and 120 min with a HF concentration of 25% (v/v. The recovery of Co and Li were 98% and 80%, respectively, with purities higher than 94%. Co and Li compounds, such as Co3O4 and LiF, were synthesized. Furthermore, it was possible to almost completely eliminate the F− ions as CaF2.

  4. An Experimental and Theoretical Study on the Kinetic Isotope Effect of C2H6 and C2D6 Reaction with OH

    KAUST Repository

    Khaled, Fathi; Giri, Binod; Szőri, Milá n; Viskolcz, Bé la; Farooq, Aamir

    2015-01-01

    We report experimental and theoretical results for the deuterated kinetic isotope effect (DKIE) of the reaction of OH with ethane (C2H6) and deuterated ethane (C2D6). The reactions were investigated behind reflected shock waves over 800–1350 K by monitoring OH radicals near 306.69 nm using laser absorption. In addition, high level CCSD(T)/cc-pV(T,Q)Z//MP2/cc-pVTZ quantum chemical and statistical rate theory calculations were performed which agreed very well with the experimental findings. The results reported herein provide the first experimental evidence that DKIE for alkanes asymptotes to a value of 1.4 at high temperatures.

  5. An Experimental and Theoretical Study on the Kinetic Isotope Effect of C2H6 and C2D6 Reaction with OH

    KAUST Repository

    Khaled, Fathi

    2015-10-30

    We report experimental and theoretical results for the deuterated kinetic isotope effect (DKIE) of the reaction of OH with ethane (C2H6) and deuterated ethane (C2D6). The reactions were investigated behind reflected shock waves over 800–1350 K by monitoring OH radicals near 306.69 nm using laser absorption. In addition, high level CCSD(T)/cc-pV(T,Q)Z//MP2/cc-pVTZ quantum chemical and statistical rate theory calculations were performed which agreed very well with the experimental findings. The results reported herein provide the first experimental evidence that DKIE for alkanes asymptotes to a value of 1.4 at high temperatures.

  6. Facile synthesis of hollow Sn-Co@PMMA nanospheres as high performance anodes for lithium-ion batteries via galvanic replacement reaction and in situ polymerization

    Science.gov (United States)

    Yu, Xiaohui; Jiang, Anni; Yang, Hongyan; Meng, Haowen; Dou, Peng; Ma, Daqian; Xu, Xinhua

    2015-08-01

    Polymethyl methacrylate (PMMA)-coated hollow Sn-Co nanospheres (Sn-Co@PMMA) with superior electrochemical performance had been synthesized via a facile galvanic replacement method followed by an in situ emulsion polymerization route. The properties were investigated in detail and results show that the hollow Sn-Co nanospheres were evenly coated with PMMA. Benefiting from the protection of the PMMA layers, the hollow Sn-Co@PMMA nanocomposite is capable of retaining a high capacity of 590 mAh g-1 after 100 cycles with a coulomb efficiency above 98%, revealing better electrochemical properties compared with hollow Sn-Co anodes. The PMMA coating could help accommodate the mechanical strain caused by volume expansion and stabilize the solid electrolyte interphase (SEI) film formed on the electrode. Such a facile process could be further extended to other anode materials for lithium-ion batteries.

  7. Green and efficient extraction strategy to lithium isotope separation with double ionic liquids as the medium and ionic associated agent

    International Nuclear Information System (INIS)

    Xu Jingjing; Li Zaijun; Gu Zhiguo; Wang Guangli; Liu Junkang

    2013-01-01

    The paper reported a green and efficient extraction strategy to lithium isotope separation. A 4-methyl-10-hydroxybenzoquinoline (ROH), hydrophobic ionic liquid-1,3-di(isooctyl)imidazolium hexafluorophosphate ([D(i-C 8 )IM][PF 6 ]), and hydrophilic ionic liquid-1-butyl-3-methylimidazolium chloride (ILCl) were used as the chelating agent, extraction medium and ionic associated agent. Lithium ion (Li + ) first reacted with ROH in strong alkali solution to produce a lithium complex anion. It then associated with IL + to form the Li(RO) 2 IL complex, which was rapidly extracted into the organic phase. Factors for effect on the lithium isotope separation were examined. To obtain high extraction efficiency, a saturated ROH in the [D(i-C 8 )IM][PF 6 ] (0.3 mol l -1 ), mixed aqueous solution containing 0.3 mol l -1 lithium chloride, 1.6 mol l -1 sodium hydroxide and 0.8 mol l -1 ILCl and 3:1 were selected as the organic phase, aqueous phase and phase ratio (o/a). Under optimized conditions, the single-stage extraction efficiency was found to be 52 %. The saturated lithium concentration in the organic phase was up to 0.15 mol l -1 . The free energy change (ΔG), enthalpy change (ΔH) and entropy change (ΔS) of the extraction process were -0.097 J mol -1 , -14.70 J mol K -1 and -48.17 J mol -1 K -1 , indicating a exothermic process. The partition coefficients of lithium will enhance with decrease of the temperature. Thus, a 25 deg C of operating temperature was employed for total lithium isotope separation process. Lithium in Li(RO) 2 IL was stripped by the sodium chloride of 5 mol l -1 with a phase ratio (o/a) of 4. The lithium isotope exchange reaction in the interface between organic phase and aqueous phase reached the equilibrium within 1 min. The single-stage isotope separation factor of 7 Li- 6 Li was up to 1.023 ± 0.002, indicating that 7 Li was concentrated in organic phase and 6 Li was concentrated in aqueous phase. All chemical reagents used can be well recycled

  8. Preparation of Tritium from irradiated lithium compounds (study)

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The aim of the present study is the selection of a certain scheme for release, collection, measurement and analysis of Tritium as produced in Lithium compounds (Li[sub 2]O, LiOH, Li[sub 2]CO[sub 3] LiF and some Lithium alloys) in accordance with the [sup 6]Li(n, [alpha])T reaction. Tritium technology is of vital concern to power reactor programmes as well as to fusion technology. Meanwhile the fields of activity include, tritium generation and mangement in fission and fusion reactors; enviromental studies, release modeling HT/HTO conversion and dose assessments, absorption/ deabsorption, monitoring and plant design; research and development, labeling, compatibility and physical chemical properties.

  9. Reaction of Topopah Spring tuff with J-13 water: a geochemical modeling approach using the EQ3/6 reaction path code

    Energy Technology Data Exchange (ETDEWEB)

    Delany, J.M.

    1985-11-25

    EQ3/6 geochemical modeling code package was used to investigate the interaction of the Topopah Spring Tuff and J-13 water at high temperatures. EQ3/6 input parameters were obtained from the results of laboratory experiments using USW G-1 core and J-13 water. Laboratory experiments were run at 150 and 250{sup 0}C for 66 days using both wafer-size and crushed tuff. EQ3/6 modeling reproduced results of the 150{sup 0}C experiments except for a small increase in the concentration of potassium that occurs in the first few days of the experiments. At 250{sup 0}C, the EQ3/6 modeling reproduced the major water/rock reactions except for a small increase in potassium, similar to that noted above, and an overall increase in aluminum. The increase in potassium concentration cannot be explained at this time, but the increase in A1 concentration is believed to be caused by the lack of thermodynamic data in the EQ3/6 data base for dachiardite, a zeolite observed as a run product at 250{sup 0}C. The ability to reproduce the majority of the experimental rock/water interactions at 150{sup 0}C validates the use of EQ3/6 as a geochemical modeling tool that can be used to theoretically investigate physical/chemical environments in support of the Waste Package Task of NNWSI.

  10. Reaction of Topopah Spring tuff with J-13 water: a geochemical modeling approach using the EQ3/6 reaction path code

    International Nuclear Information System (INIS)

    Delany, J.M.

    1985-01-01

    EQ3/6 geochemical modeling code package was used to investigate the interaction of the Topopah Spring Tuff and J-13 water at high temperatures. EQ3/6 input parameters were obtained from the results of laboratory experiments using USW G-1 core and J-13 water. Laboratory experiments were run at 150 and 250 0 C for 66 days using both wafer-size and crushed tuff. EQ3/6 modeling reproduced results of the 150 0 C experiments except for a small increase in the concentration of potassium that occurs in the first few days of the experiments. At 250 0 C, the EQ3/6 modeling reproduced the major water/rock reactions except for a small increase in potassium, similar to that noted above, and an overall increase in aluminum. The increase in potassium concentration cannot be explained at this time, but the increase in A1 concentration is believed to be caused by the lack of thermodynamic data in the EQ3/6 data base for dachiardite, a zeolite observed as a run product at 250 0 C. The ability to reproduce the majority of the experimental rock/water interactions at 150 0 C validates the use of EQ3/6 as a geochemical modeling tool that can be used to theoretically investigate physical/chemical environments in support of the Waste Package Task of NNWSI

  11. Electrolytic method for the production of lithium using a lithium-amalgam electrode

    Science.gov (United States)

    Cooper, John F.; Krikorian, Oscar H.; Homsy, Robert V.

    1979-01-01

    A method for recovering lithium from its molten amalgam by electrolysis of the amalgam in an electrolytic cell containing as a molten electrolyte a fused-salt consisting essentially of a mixture of two or more alkali metal halides, preferably alkali metal halides selected from lithium iodide, lithium chloride, potassium iodide and potassium chloride. A particularly suitable molten electrolyte is a fused-salt consisting essentially of a mixture of at least three components obtained by modifying an eutectic mixture of LiI-KI by the addition of a minor amount of one or more alkali metal halides. The lithium-amalgam fused-salt cell may be used in an electrolytic system for recovering lithium from an aqueous solution of a lithium compound, wherein electrolysis of the aqueous solution in an aqueous cell in the presence of a mercury cathode produces a lithium amalgam. The present method is particularly useful for the regeneration of lithium from the aqueous reaction products of a lithium-water-air battery.

  12. {sup 16}O resonances near 4α threshold through {sup 12}C({sup 6}Li,d) reaction

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, M. R. D.; Borello-Lewin, T.; Miyake, H.; Horodynski-Matsushigue, L. B.; Duarte, J. L. M.; Rodrigues, C. L.; Faria, P. Neto de [Instituto de Física, Universidade de São Paulo, Caixa Postal 66318, CEP 05314-970, São Paulo, SP (Brazil); Cunsolo, A.; Cappuzzello, F.; Foti, A.; Agodi, C.; Cavallaro, M. [INFN - Laboratori Nazionali del Sud, Via S. Sofia 62, 95125 Catania (Italy); Napoli, M. di; Ukita, G. M. [Faculdade de Psicologia, Universidade de Santo Amaro, R. Prof. Eneas da Siqueira Neto, 340, CEP 04829-300, São Paulo, SP (Brazil)

    2014-11-11

    Several narrow alpha resonant {sup 16}O states were detected through the {sup 12}C({sup 6}Li,d) reaction, in the range of 13.5 to 17.5 MeV of excitation energy. The reaction was measured at a bombarding energy of 25.5 MeV employing the São Paulo Pelletron-Enge-Spectrograph facility and the nuclear emulsion technique. Experimental angular distributions associated with natural parity quasi-bound states around the 4α threshold are presented and compared to DWBA predictions. The upper limit for the resonance widths obtained is near the energy resolution (15 keV)

  13. Inclusive break-up reactions of 6Li at an incident energy of 26 MeV/nucleon

    International Nuclear Information System (INIS)

    Shyam, R.; Machner, H.; Neumann, B.; Rebel, H.; Gils, H.J.; Planeta, R.; Buschmann, J.; Klewe-Nebenius, H.; Zagromski, S.

    1982-01-01

    Inclusive charged particle spectra were measured from nuclear reactions induced by 156 MeV 6 Li on 40 Ca. At forward angles the spectra exhibit broad break-up distributions centered around the energy corresponding to the beam velocity. The double differential cross sections together with previous results for a 208 Pb target were analyzed in the framework of the DWBA approach to projectile break-up taking into account elastic and inelastic reactions of the break-up fragments. The high energy tails of the background due to preequilibrium emission of complex charged particles were estimated on the basis of the coalescence model. (orig.) [de

  14. Inclusive break-up reactions of 6Li at an incident energy of 26 MeV/nucleon

    International Nuclear Information System (INIS)

    Neumann, B.; Rebel, H.; Gils, H.J.; Planeta, R.; Buschmann, J.; Klewe-Nebenius, H.; Zagromski, S.; Shyam, R.; Machner, H.

    1982-01-01

    Inclusive charged particle spectra were measured from nuclear reactions induced by 156 MeV 6 Li on 40 Ca. At forward angles the spectra exhibit broad break-up distributions centered around the energy corresponding to the beam velocity. The double differential cross sections together with previous results for a 208 Pb target were analyzed in the framework of the DWBA approach to projectile break-up taking into account elastic and inelastic reactions of the break-up fragments. The high energy tails of the background due to preequilibrium emission of complex charged particles were estimated on the basis of the coalescence model. (orig.)

  15. Towards Safer Lithium-Ion Batteries

    OpenAIRE

    Herstedt, Marie

    2003-01-01

    Surface film formation at the electrode/electrolyte interface in lithium-ion batteries has a crucial impact on battery performance and safety. This thesis describes the characterisation and treatment of electrode interfaces in lithium-ion batteries. The focus is on interface modification to improve battery safety, in particular to enhance the onset temperature for thermally activated reactions, which also can have a negative influence on battery performance. Photoelectron Spectroscopy (PES) ...

  16. Elastic scattering and total reaction cross section for the {sup 6}He+{sup 58}Ni system

    Energy Technology Data Exchange (ETDEWEB)

    Morcelle, V. [Instituto de Física - Universidade Federal Fluminense, 24210-346, Rio de Janeiro, Brazil and Universidade Federal de Itajubá, 35900-030, Itabira (Brazil); Lichtenthäler, R.; Lépine-Szily, A.; Guimarães, V.; Gasques, L.; Scarduelli, V.; Condori, R. Pampa; Leistenschneider, E. [Depto de Física Nuclear, Universidade de São Paulo, C.P. 66318, 05389-970, São Paulo (Brazil); Mendes Jr, D. R.; Faria, P. N. de [Instituto de Física - Universidade Federal Fluminense, 24210-346, Rio de Janeiro (Brazil); Pires, K. C. C. [Universidade Tecnológica Federal do Paraná, 86300-000, Cornélio Procópio (Brazil); Barioni, A. [Instituto de Física, Universidade Federal da Bahia, 40210-340, Bahia (Brazil); Morais, M. C. [Centro Brasileiro de Pesquisas Físicas, 22290-180, Rio de Janeiro (Brazil); Shorto, J. M. B. [Instituto de Pesquisas Energéticas e Nucleares- IPEN, 05508-000, São Paulo (Brazil); Zamora, J. C. [Departament of Physics, Technische Universität Darmstadt (Germany)

    2014-11-11

    Elastic scattering measurements of {sup 6}He + {sup 58}Ni system have been performed at the laboratory energy of 21.7 MeV. The {sup 6}He secondary beam was produced by a transfer reaction {sup 9}Be ({sup 7}Li, {sup 6}He) and impinged on {sup 58}Ni and {sup 197}Au targets, using the Radioactive Ion Beam (RIB) facility, RIBRAS, installed in the Pelletron Laboratory of the Institute of Physics of the University of São Paulo, Brazil. The elastic angular distribution was obtained in the angular range from 15° to 80° in the center of mass frame. Optical model calculations have been performed using a hybrid potential to fit the experimental data. The total reaction cross section was derived.

  17. Lithium Resources and Production: Critical Assessment and Global Projections

    Directory of Open Access Journals (Sweden)

    Steve H. Mohr

    2012-03-01

    Full Text Available This paper critically assesses if accessible lithium resources are sufficient for expanded demand due to lithium battery electric vehicles. The ultimately recoverable resources (URR of lithium globally were estimated at between 19.3 (Case 1 and 55.0 (Case 3 Mt Li; Best Estimate (BE was 23.6 Mt Li. The Mohr 2010 model was modified to project lithium supply. The Case 1 URR scenario indicates sufficient lithium for a 77% maximum penetration of lithium battery electric vehicles in 2080 whereas supply is adequate to beyond 2200 in the Case 3 URR scenario. Global lithium demand approached a maximum of 857 kt Li/y, with a 100% penetration of lithium vehicles, 3.5 people per car and 10 billion population.

  18. Complete and incomplete fusion dynamics of {sup 6,7}Li + {sup 159}Tb reactions near the Coulomb barrier

    Energy Technology Data Exchange (ETDEWEB)

    Gautam, Manjeet Singh [Thapar University, School of Physics and Materials Science, Patiala (India); Indus Degree College, Department of Physics, Kinana, Jind, Haryana (India); Grover, Neha; Sharma, Manoj K. [Thapar University, School of Physics and Materials Science, Patiala (India)

    2017-01-15

    The complete fusion (CF) and incomplete fusion (ICF) cross-sections are estimated for {sup 6,} {sup 7}Li + {sup 159}Tb reactions using the energy-dependent Woods-Saxon potential model (EDWSP model) and dynamical cluster-decay model (DCM). The CF data of the {sup 6}Li + {sup 159}Tb({sup 7}Li + {sup 159}Tb) reaction at above barrier energies is suppressed with reference to expectations of the EDWSP model by 25% (20%) which is smaller than the reported data by ∝ 9% (6%). This suppression is correlated with the projectile breakup effect. The projectiles {sup 6,7}Li are loosely bound systems, which may break up into charged fragments prior to reaching the fusion barrier and subsequently one of the fragment is captured by the target leading to the suppression of fusion data at above barrier energies. The sum of CF and ICF, which is termed as total fusion cross-section (TF), removes the discrepancies between theoretical predictions and the above barrier complete fusion data and hence is adequately explained via the EDWSP model over a wide range of energy spread across the Coulomb barrier. In addition to fusion, the decay mechanism of {sup 6}Li + {sup 159}Tb reaction is studied within the framework of the dynamical cluster-decay model (DCM). The breakup of the projectile ({sup 6}Li) in the entrance channel indicates the presence of ICF, which is investigated further using the collective clusterization approach of DCM. The present theoretical analysis suggests that a larger barrier modification is needed to address the fusion data of chosen reactions in the below barrier energy region. (orig.)

  19. Search for 4H, 5H and 6H nuclei in the 11B-induced reaction on 9Be

    International Nuclear Information System (INIS)

    Belozerov, A.V.; Borcea, C.; Dlouhy, Z.

    1985-01-01

    In the 11 B(88.0 MeV)+ 9 Be reaction the energy spectra of the 14 O, 15 O and 16 O nuclei have been measured to obtain some information about their partners in the exit channel - the neutron-rich hydrogen isotopes 4 H, 5 H and 6 H. The unbound levels in the 4 H and 6 H systems have been observed at excitation energies of 3.5 +- 0.5 MeV (GITA approximately 1 MeV) and 2.6 +- 0.5 MeV (GITA=1.5 +- 0.3 MeV), respectively

  20. Fusion cross sections for 6,7Li + 24Mg reactions at energies below and above the barrier

    International Nuclear Information System (INIS)

    Ray, M.; Mukherjee, A.; Pradhan, M. K.; Kshetri, Ritesh; Sarkar, M. Saha; Dasmahapatra, B.; Palit, R.; Majumdar, I.; Joshi, P. K.; Jain, H. C.

    2008-01-01

    Measurement of fusion cross sections for the 6,7 Li + 24 Mg reactions by the characteristic γ-ray method has been done at energies from below to well above the respective Coulomb barriers. The fusion cross sections obtained from these γ-ray cross sections for the two systems are found to agree well with the total reaction cross sections at low energies. The relatively large difference between total cross sections and measured fusion cross sections at higher energies is consistent with the fact that other channels, in particular breakup, open up with an increase of bombarding energy. The breakup channel, however, appears not to have any influence on fusion cross sections. The critical angular momenta (l cr ) deduced from the fusion cross sections are found to have an energy dependence similar to other Li-induced reactions

  1. Systematics of (n,t) reactions in medium and heavy mass nuclei at 14.6 MeV

    International Nuclear Information System (INIS)

    Woo, T.T.

    1979-01-01

    The production cross sections for (n,t) reactions of 14.6-MeV neutrons with isotopes of the natural elements Ca, Ti, Cr, Fe, Ni, Y, Mo, Pd, Cd, Sn, Pb, La, and with the enriched isotopes 86 Sr, 114 Cd, 130 Te, 205 Tl were measured by the activation technique using high-energy resolution gamma-ray spectrometry. The systematics for the (n,t) reactions were investigated as a function of the relative neutron excess. The experimentally determined values of the cross sections are in good agreement with values calculated by an empirical equation. The cross section ratios (n,t) and (n,p) reactions were calculated on the basis of the statistical model

  2. Measurement of the cross section of the 8Li(d,α)6He reaction of possible relevance to big bang nucleosynthesis

    International Nuclear Information System (INIS)

    Sahin, L.; Boyd, R.N.; Cole, A.L.; Famiano, M.; Gueray, R.T.; Murphy, A. St.J.; Oezkan, N.; Kolata, J.J.; Guimaraes, V.; Hencheck, M.

    2002-01-01

    We report measurements of the cross section of the 8 Li(d,α) 6 He reaction in the energy range E c.m. =2.3-3.5 MeV using a 8 Li-radioactive beam on a CD 2 foil. The astrophysical S factor and reaction rate were calculated from the measured cross section. The 6 He nuclei produced in the reaction were detected in solid-state detector telescopes. This reaction might have affected the primordial abundance of 6 Li in big bang nucleosynthesis, since 6 He beta decays to 6 Li. However, several big bang nucleosynthesis network calculations were found to be insensitive to this reaction, suggesting that the 8 Li(d,α) 6 He reaction does not affect 6 Li primordial production

  3. All-solid-state lithium batteries – The Mg2FeH6-electrode LiBH4-electrolyte system

    DEFF Research Database (Denmark)

    Huen, Priscilla; Ravnsbæk, Dorthe B.

    2018-01-01

    The complex hydride Mg2FeH6 is investigated as conversion type anode in a solid-state all-hydride Li-battery employing LiBH4 as solid-state electrolyte. In the solid-state battery, Mg2FeH6 exhibits improvements in the capacity retention and initial Coulombic efficiency of > 3 and > 2.5 times......, respectively, compared to the conventional liquid-electrolyte battery. Through investigations of the conversion reactions of Mg2FeH6, formation of MgH2 as intermediate in the conversion to Mg is discovered the first time. In addition, the effect of mixing procedure for the electrode-electrolyte composite...... on the battery performance is discussed....

  4. Characterization of positive electrode/electrolyte interphase in lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Dupre, N.; Martin, J.F.; Soudan, P.; Guyomard, D. [Inst.des Materiaux Jean Rouxel, Nantes (France)

    2008-07-01

    Lithium batteries appear to be the most viable energy source for portable electronic devices because of their energy density. The solid electrolyte interphase (SEI) between the negative electrode and the electrolyte of a Li-ion battery monitors the overall battery behaviour in terms of irreversible capacity loss, charge transfer kinetics and storage properties. This paper reported on a study that examined the influence of the storage atmosphere and the formation of a protective surface layer on the electrochemical performance. The objective was to better understand the interfacial problems controlling the long term life duration and cyclability. The positive/electrolyte interphase evolution was followed upon aging/cycling using 7Li MAS NMR, XPS and impedance spectroscopy. This very novel and uncommon technique was used to characterize the growth and evolution of the surface of some electrode materials for lithium batteries, due to contact with the ambient atmosphere or electrolyte or along electrochemical cycling. LiFePO4 and LiMn0.5Ni0.5O2 were chosen for the studies because they are among the most promising candidates for positive electrodes for future lithium batteries. The reaction of LiMn0.5Ni0.5O2 with the ambient atmosphere or LiPF6 electrolyte is extremely fast and leads to an important amount of lithium-containing diamagnetic species. The NMR spectra provided valuable structural information on the interaction between the interphase and the active material after contact with electrolyte or along electrochemical cycling. MAS NMR was shown to be a very promising tool to monitor phenomena taking place at the interface between electrode and electrolyte in lithium batteries. The study showed the affect of the potential on the strength of the interaction between the surface layer and the active material and the partial removal of this layer along the electrochemical cycling. 11 refs.

  5. Probing the role of Skyrme interactions on the fission dynamics of the {sup 6}Li + {sup 238}U reaction

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Ishita; Kumar, Raj; Sharma, Manoj K. [Thapar University, School of Physics and Materials Science, Patiala (India)

    2017-06-15

    The performance of selected five Skyrme forces (out of a set of 240), tested by Dutra et al., is analyzed in view of fusion-fission dynamics. These forces are assumed to perform better for neutron-rich systems, so the choice of the reaction is accordingly made by opting for a neutron-rich target in {sup 6}Li + {sup 238}U reaction. This reaction is diagnosed further in reference to fusion hindrance within the dynamical approach of the cluster-decay model (DCM). In order to reduce the computational time, three Skyrme forces are figured out with the criteria that these forces cover the barrier characteristics of the remaining two forces as well. The fission cross-sections are successfully addressed at low energies for the {sup 6}Li + {sup 238}U reaction. However, at relatively higher energies, the excitation functions show theoretical suppression with respect to experimental data, which may be associated with the possible existence of incomplete fusion (ICF). For ICF, we have considered that the {sup 6}Li broke into {sup 4}He + {sup 2}H, as mentioned in the experimental work. The calculations of ICF are carried out for the {sup 4}He + {sup 238}U reaction with the selected Skyrme forces at E{sub c.m.} = 26.20 and 27.51 MeV. These forces address the data nicely for the compound nucleus (CN) as well as ICF processes. Here, the NRAPR force seems to require lesser barrier modification as compared to the other forces, therefore it can be used as an alternate choice for calculating the interaction potential. Additionally, the prediction of cross-sections at lower energies has been done with DCM using the NRAPR force. The l-dependent % barrier modification of the Skyrme forces undertaken is also worked out in reference to fusion hindrance at below barrier energies. (orig.)

  6. Highly Reversible Electrochemical Insertion of Lithium, Accompanied With a Marked Color Change, Occuring in Microcrystalline Lithium Nickel Oxide Films

    OpenAIRE

    Campet, G.; Portier, J.; Morel, B.; Ferry, D.; Chabagno, J. M.; Benotmane, L.; Bourrel, M.

    1992-01-01

    Thin films of lithium-nickel oxide, whose texture consists of microcrystallites with an average grain size of 50 Å, permit highly reversible electrochemical insertion of lithium ions in Li+ conducting electrolytes. Therefore, the corresponding materials would be of great interest for energy storage applications. In addition, the lithium insertion/extraction reactions in the nickel-based layers are accompanied with a marked color change, making these films of interest for the devel...

  7. Low-energy cross sections of the BBN reaction d({alpha},{gamma}){sup 6}Li by Coulomb dissociation of {sup 6}Li

    Energy Technology Data Exchange (ETDEWEB)

    Heil, Michael; Suemmerer, Klaus [GSI Darmstadt (Germany); Hammache, Fairouz [IPN Orsay (France); Galaviz, Daniel [TU Darmstadt (Germany); Typel, Stefan [GANIL Caen (France)

    2008-07-01

    The primordial abundances of D, ({sup 3}He), {sup 4}He, and {sup 7}Li can be used to infer the baryon density of the Universe based on the framework of Big-Bang Nucleosynthesis (BBN). By precision measurements of the cosmic microwave background (CMB) an independent method became available recently. This lead to a renewed interest for BBN. Together with the recent observation of {sup 6}Li in old stars and the problems to reconcile calculated primordial {sup 7}Li abundances with those predicted on the basis of CMB results, the production of both, {sup 6}Li and {sup 7}Li in BBN has been reinvestigated. One important ingredient is the low-energy S-factor of the d-alpha radiative-capture reaction. Up to now, the only available experimental result by Kiener et al. (1991) introduced an uncertainty of about a factor of 20 in the {sup 6}Li yield. We have therefore reinvestigated the d-alpha reaction with the help of Coulomb dissociation (CD) of {sup 6}Li at 150 MeV/nucleon at GSI. CD is the only practical way to study the low-energy S-factor (which involves l=2 multipolarity) due to the large number of E2 photons contained in the equivalent-photon flux. Preliminary results indicate a drop of the S-factor as predicted by theory, contrary to the constant low-energy S-factor resulting from the previous study.

  8. Lithium-based neutron detectors

    International Nuclear Information System (INIS)

    Yursova, L.

    1977-01-01

    The problems of using scintillation lithium-based detectors (LiJ(Eu) and 6 LiJ(Eu)), as well as lithium glasses for neutron detection are described. As compared with the glasses the LiJ(Eu) monocrystal possesses substantially higher energy resolution, its luminescence yield is considerably higher (in some cases ten fold), its application makes possible gamma radiation discrimination with the energy approximately four times higher and its higher specific mass ensures better efficiency of gamma radiation counting. The only 6 LiJ(Eu) drawback is its high hydroscopicity as well as its possibility to be used only in a limited temperature range (maximum temperature +35 deg C). The lithium glass can be used (with the exception of spectrometric measurements and radiation mixed regions measurement) with more than 1 MeV gamma radiation energy in a wide temperature range, in agressive, corroding and acid media

  9. Lithium reserves and resources

    International Nuclear Information System (INIS)

    Evans, R.K.

    1978-01-01

    As a result of accelerating research efforts in the fields of secondary batteries and thermonuclear power generation, concern has been expressed in certain quarters regarding the availability, in sufficient quantities, of lithium. As part of a recent study by the National Research Council on behalf of the Energy Research and Development Administration, a subpanel was formed to consider the outlook for lithium. Principal areas of concern were reserves, resources and the 'surplus' available for energy applications after allowing for the growth in current lithium applications. Reserves and resources were categorized into four classes ranging from fully proved reserves to resources which are probably dependent upon the marketing of co-products to become economically attractive. Because of the proprietary nature of data on beneficiation and processing recoveries, the tonnages of available lithium are expressed in terms of plant feed. However, highly conservative assumptions have been made concerning mining recoveries and these go a considerable way to accounting for total losses. Western World reserves and resources of all classes are estimated at 10.6 million tonnes Li of which 3.5 million tonnes Li are located in the United States. Current United States capacity, virtually equivalent to Western World capacity, is 4700 tonnes Li and production in 1976 approximated to 3500 tonnes Li. Production for current applications is expected to grow to approx. 10,000 tonnes in year 2000 and 13,000 tonnes a decade later. The massive excess of reserves and resources over that necessary to support conventional requirements has limited the amount of justifiable exploration expenditures; on the last occasion, there was a a major increase in demand (by the USAEA) reserves and capacity were increased rapidly. There are no foreseeable reasons why this shouldn't happen again when the need is clear. (author)

  10. Conductometric study of reaction kinetics between potassium superoxide and 18-crown-6 in dimethylsulfoxide

    International Nuclear Information System (INIS)

    Efimova, I.V.; Opejda, I.A.

    2000-01-01

    Complexing within KO 2 -18-crown-6-solvent, KOH-18-crown-6-solvent and KI-KO 2 -18-crown-6-solvent systems in dimethylsulfoxide was studied by measurement of electrical conductivity. It was shown that time variation of electrical conductivity under the given conditions was described by the Erofeev-Auramy equation, the coefficients of that equation for various systems were determined, time to reach equilibrium state was estimated. Linear dependences of electrical conductivity of KI-KO 2 salt solutions at presence of 18-crown-6 at the state of equilibrium in contrast to the component concentrations were determined [ru

  11. Recovery and recycling of lithium value from spent lithium titanate (Li{sub 2}TiO{sub 3}) pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Mandal, D., E-mail: dmandal10@gmail.com

    2013-09-15

    Graphical abstract: Effects of various process parameters on the recovery of Li-from spent Li{sub 2}TiO{sub 3} pebbles were investigated. From the experimental results it was observed that the leaching rate increases with speed of stirring till 450 rpm and then above 450 rpm; the increase in speed of stirring does not have any significant effect on the leaching rate as shown in the following figure. Effects of other parameters on the Li-recovery from spent Li{sub 2}TiO{sub 3} pebbles are discussed in this paper. Abstract: In the first generation fusion reactors the fusion of deuterium (D) and tritium (T) is considered to produce energy to meet the future energy demand. Deuterium is available in nature whereas, tritium is not. Lithium-6 (Li{sup 6}) isotope has the ability to produce tritium in the n, α nuclear reaction with neutrons. Thus lithium-based ceramics enriched by Li{sup 6} isotope are considered for the tritium generation for its use in future fusion reactors. Lithium titanate is one such Li-based ceramic material being considered for its some attractive properties viz., high thermal and chemical stability, high thermal conductivity, and low tritium solubility. It is reported in the literature, that the burn up of these pebbles in the fusion reactor will be limited to only 15–17 atomic percentage. At the end of life, the pebbles will contain more than 45% unused Li{sup 6} isotope. Due to the high cost of enriched Li{sup 6} and the waste disposal considerations, it is necessary to recover the unused Li from the spent lithium titanate pebbles. Till date, only the feasibilities of different processes are reported, but no process details are available. Experiments were carried out for the recovery of Li from simulated Li{sub 2}TiO{sub 3} pebbles and to reuse of lithium in lithium titanate pebble fabrication. The details of the experiments and results are discussed in this paper.

  12. Extraction with SPME and Synthesis of 2-Methyl-6-vinylpyrazine by a ‘One Pot’ Reaction Using Microwaves

    Directory of Open Access Journals (Sweden)

    René Arzuffi

    2009-06-01

    Full Text Available A synthesis of 2-methyl-6-vinylpyrazine was carried out by way of a ‘one pot’ reaction. In order to establish the efficiency of this synthesis the extraction of the volatiles released by male papaya fruit flies was performed by SPME (solid phase micro-extraction. The compound was separated and identified using GC/MSD (gas chromatography/mass spectrometry detector.

  13. Study of breakup and transfer of weakly bound nucleus 6Li to explore the low energy reaction dynamics

    Directory of Open Access Journals (Sweden)

    Zhang G. L.

    2017-01-01

    In order to have a proper understanding of the influence of breakup and transfer of weakly bound projectiles on the fusion process, we performed the 6Li+89Y experiment with incident energies of 22 MeV and 34 MeV on Galileo array in cooperation with Si-ball EUCLIDES at Legnaro National Laboratory (LNL in Italy. Using particle-particle and particle-γ coincidences, the different reaction mechanisms can be clearly explored.

  14. Lanthanum Nitrate As Electrolyte Additive To Stabilize the Surface Morphology of Lithium Anode for Lithium-Sulfur Battery.

    Science.gov (United States)

    Liu, Sheng; Li, Guo-Ran; Gao, Xue-Ping

    2016-03-01

    Lithium-sulfur (Li-S) battery is regarded as one of the most promising candidates beyond conventional lithium ion batteries. However, the instability of the metallic lithium anode during lithium electrochemical dissolution/deposition is still a major barrier for the practical application of Li-S battery. In this work, lanthanum nitrate, as electrolyte additive, is introduced into Li-S battery to stabilize the surface of lithium anode. By introducing lanthanum nitrate into electrolyte, a composite passivation film of lanthanum/lithium sulfides can be formed on metallic lithium anode, which is beneficial to decrease the reducibility of metallic lithium and slow down the electrochemical dissolution/deposition reaction on lithium anode for stabilizing the surface morphology of metallic Li anode in lithium-sulfur battery. Meanwhile, the cycle stability of the fabricated Li-S cell is improved by introducing lanthanum nitrate into electrolyte. Apparently, lanthanum nitrate is an effective additive for the protection of lithium anode and the cycling stability of Li-S battery.

  15. The extraction and determination of free lithium in Li-B alloys

    International Nuclear Information System (INIS)

    Kilroy, W.P.; Angres, I.

    1979-01-01

    Extraction of the lithium phase from lithium-rich Li-B alloys was achieved by reaction of the alloy with dry naphthalene dissolved in anhydrous tetrahydrofuran. The resulting radical anion was hydrolyzed and the lithium was determined by potentiometric titration from the moles of hydroxide formed. The composition of the Lisub(x)Bsub(y) residue was determined by difference. (Auth.)

  16. Experimental investigation of the lithium transport mechanisms in cementitious materials by NMR

    NARCIS (Netherlands)

    Venglovska, S.; Pel, L.; Adan, O.C.G.; Bakker, J.; Frangopol, D.M.; van Breugel, K.

    2017-01-01

    Lithium hydroxide can help to reduce and control the expansion of concrete caused by Alkalisilica reaction. In new concrete structures the lithium ions can be introduced as admixture to prevent ASR deleterious expansion. In existing structures the lithium ions need to be transported into the

  17. Facile synthesis of hollow Sn–Co@PMMA nanospheres as high performance anodes for lithium-ion batteries via galvanic replacement reaction and in situ polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Xiaohui; Jiang, Anni; Yang, Hongyan; Meng, Haowen; Dou, Peng; Ma, Daqian [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Xu, Xinhua, E-mail: xhxutju@gmail.com [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China)

    2015-08-30

    Highlights: • Hollow Sn–Co nanospheres were synthesized via a facile galvanic replacement method. • PMMA layers were uniform coated on the surface of Sn–Co composites via in situ emulsion polymerization. • The coating layers are beneficial to suppress the aggregation and stabilize the SEI formation on the surface. • Excellent cycling stability and rate capability were obtained by coating PMMA protective layers on the surface of hollow Sn–Co nanospheres. - Abstract: Polymethyl methacrylate (PMMA)-coated hollow Sn–Co nanospheres (Sn–Co@PMMA) with superior electrochemical performance had been synthesized via a facile galvanic replacement method followed by an in situ emulsion polymerization route. The properties were investigated in detail and results show that the hollow Sn–Co nanospheres were evenly coated with PMMA. Benefiting from the protection of the PMMA layers, the hollow Sn–Co@PMMA nanocomposite is capable of retaining a high capacity of 590 mAh g{sup −1} after 100 cycles with a coulomb efficiency above 98%, revealing better electrochemical properties compared with hollow Sn–Co anodes. The PMMA coating could help accommodate the mechanical strain caused by volume expansion and stabilize the solid electrolyte interphase (SEI) film formed on the electrode. Such a facile process could be further extended to other anode materials for lithium-ion batteries.

  18. Facile synthesis of hollow Sn–Co@PMMA nanospheres as high performance anodes for lithium-ion batteries via galvanic replacement reaction and in situ polymerization

    International Nuclear Information System (INIS)

    Yu, Xiaohui; Jiang, Anni; Yang, Hongyan; Meng, Haowen; Dou, Peng; Ma, Daqian; Xu, Xinhua

    2015-01-01

    Highlights: • Hollow Sn–Co nanospheres were synthesized via a facile galvanic replacement method. • PMMA layers were uniform coated on the surface of Sn–Co composites via in situ emulsion polymerization. • The coating layers are beneficial to suppress the aggregation and stabilize the SEI formation on the surface. • Excellent cycling stability and rate capability were obtained by coating PMMA protective layers on the surface of hollow Sn–Co nanospheres. - Abstract: Polymethyl methacrylate (PMMA)-coated hollow Sn–Co nanospheres (Sn–Co@PMMA) with superior electrochemical performance had been synthesized via a facile galvanic replacement method followed by an in situ emulsion polymerization route. The properties were investigated in detail and results show that the hollow Sn–Co nanospheres were evenly coated with PMMA. Benefiting from the protection of the PMMA layers, the hollow Sn–Co@PMMA nanocomposite is capable of retaining a high capacity of 590 mAh g −1 after 100 cycles with a coulomb efficiency above 98%, revealing better electrochemical properties compared with hollow Sn–Co anodes. The PMMA coating could help accommodate the mechanical strain caused by volume expansion and stabilize the solid electrolyte interphase (SEI) film formed on the electrode. Such a facile process could be further extended to other anode materials for lithium-ion batteries

  19. Controlling the photochemical reaction of an azastilbene derivative in water using a water-soluble pillar[6]arene.

    Science.gov (United States)

    Xia, Danyu; Wang, Pi; Shi, Bingbing

    2017-09-20

    Photochemistry plays an important role in our lives. It has also been a common tool in the laboratory to construct complicated systems from small molecules. Supramolecular chemistry provides an opportunity to solve some of the problems in controlling photochemical reactions via non-covalent interactions. By using confining media and weak interactions between the medium and the reactant molecule, the excited state behavior of molecules has been successfully manipulated. Pillararenes, a new class of macrocyclic hosts, have rarely been used in the field of photochemical investigations, such as the controlling of photo-induced reactions. Herein, we explore a synthetic macrocyclic host, a water-soluble pillar[6]arene, as a controlling tool to manipulate the photo-induced reactions (hydration) in water. A host-guest system in water based on a water-soluble pillar[6]arene and an azastilbene derivative, (E)-4,4'-dimethyl-4,4'-diazoniastilbene diiodide, has been constructed. Then this water-soluble pillar[6]arene was successfully employed to control the photohydration of the azastilbene derivative in water as a "protective agent".

  20. Formation reactions and thermal stability of Ca/sub 2/NbCoO/sub 6/ and Ca/sub 2/TaCoO/sub 6/

    Energy Technology Data Exchange (ETDEWEB)

    Kuleshova, T B; Razumovskaya, O N; Belyaev, I N; Salei, V S [Rostovskij-na-Donu Gosudarstvennyj Univ. (USSR)

    1979-11-01

    Ca/sub 2/M/sup 5/CoO/sub 6/ compounds and reactions of their formation from oxides were investigated by thermogravimetric and X-ray phase analysis methods. Optimum conditions for synthesizing the above compounds have been found, and the degree of oxidation of Co therein, determined. The thermal stability of the compounds was also studied. It was shown, that the stability of Co (3) in Ca/sub 2/NbCaO/sub 6/ Ca/sub 2/TaCoO/sub 6/ is higher than that in similar compounds containing Pb. The resultant compounds are pure perovskites. Presented are the calculated and the experimental values of perovskite cell parameters.

  1. A shock tube study of C4–C6 straight chain alkenes + OH reactions

    KAUST Repository

    Khaled, Fathi

    2016-06-28

    Alkenes are known to be good octane boosters and they are major components of commercial fuels. Detailed theoretical calculations and direct kinetic measurements of elementary reactions of alkenes with combustion radicals are scarce for C4 alkenes and they are practically absent for C5 and larger alkenes. The overall rate coefficients for the reaction of OH radical with 1-butene (CH CHCH CH, k ), 1-pentene (CH CHCH CH-CH, k ), cis/trans 2-pentene (CH CHCHCH CH, k and k ), 1-hexene (CH CHCH CH CH CH, k ) and cis/trans 2-hexene (CH CHCHCH CH CH, k and k ) were measured behind reflected shock waves over the temperature range of 833-1377K and pressures near 1.5atm. The reaction progress was followed by measuring mole fraction of OH radicals near 306.7nm using UV laser absorption technique. It is found that the rate coefficients of OH+trans-2-alkenes are larger than those of OH+cis-2-alkenes, followed by OH+1-alkenes. The derived Arrhenius expressions for the overall rate coefficients (in cm.mol.s) are:. kI=(4.83±0.03)104.T2.72±0.01.exp(940.8±2.9cal/molRT)(946K-1256K) + kII=(5.66±0.54)10-1.T4.14±0.80.exp(4334±227cal/molRT)(875K-1379K) + kIII=(3.25±0.12)104.T2.76±0.5.exp(1962±83cal/molRT)(877K-1336K) + kIV=(3.42±0.09)104.T2.76±0.5.exp(1995±59cal/molRT)(833K-1265K) + kV=(7.65±0.58)10-4.T5±1.exp(5840±175cal/molRT)(836K-1387K) + kVI=(2.58±0.06)106.T2.17±0.37.exp(1461±55cal/molRT)(891K-1357K) + kVII=(3.08±0.05)106.T2.18±0.37.exp(1317±38cal/molRT)(881K-1377K) +

  2. A shock tube study of C4–C6 straight chain alkenes + OH reactions

    KAUST Repository

    Khaled, Fathi; Badra, Jihad; Farooq, Aamir

    2016-01-01

    Alkenes are known to be good octane boosters and they are major components of commercial fuels. Detailed theoretical calculations and direct kinetic measurements of elementary reactions of alkenes with combustion radicals are scarce for C4 alkenes and they are practically absent for C5 and larger alkenes. The overall rate coefficients for the reaction of OH radical with 1-butene (CH CHCH CH, k ), 1-pentene (CH CHCH CH-CH, k ), cis/trans 2-pentene (CH CHCHCH CH, k and k ), 1-hexene (CH CHCH CH CH CH, k ) and cis/trans 2-hexene (CH CHCHCH CH CH, k and k ) were measured behind reflected shock waves over the temperature range of 833-1377K and pressures near 1.5atm. The reaction progress was followed by measuring mole fraction of OH radicals near 306.7nm using UV laser absorption technique. It is found that the rate coefficients of OH+trans-2-alkenes are larger than those of OH+cis-2-alkenes, followed by OH+1-alkenes. The derived Arrhenius expressions for the overall rate coefficients (in cm.mol.s) are:. kI=(4.83±0.03)104.T2.72±0.01.exp(940.8±2.9cal/molRT)(946K-1256K) + kII=(5.66±0.54)10-1.T4.14±0.80.exp(4334±227cal/molRT)(875K-1379K) + kIII=(3.25±0.12)104.T2.76±0.5.exp(1962±83cal/molRT)(877K-1336K) + kIV=(3.42±0.09)104.T2.76±0.5.exp(1995±59cal/molRT)(833K-1265K) + kV=(7.65±0.58)10-4.T5±1.exp(5840±175cal/molRT)(836K-1387K) + kVI=(2.58±0.06)106.T2.17±0.37.exp(1461±55cal/molRT)(891K-1357K) + kVII=(3.08±0.05)106.T2.18±0.37.exp(1317±38cal/molRT)(881K-1377K) +

  3. Reaction of LaB6 with MoSi2

    International Nuclear Information System (INIS)

    Ordan'yan, S.S.; Gardagina, E.N.; Barabanova, S.N.

    1989-01-01

    Investigation results of interaction in LaB 6 -MoSi 2 system within wide concentration and temperature ranges are presented. LaB 6 and MoSi 2 powders were preliminary squeezed out in vacuum at 1470 K. Presence of LaB 6 and MoSi 2 initial phases only is determined using X-ray pahse analysis of sintered and melted specimens of all compositions. Traces of MoB (probably, due to quick crystallization after melting and partial evaporation of silicon from the melt) are detected in some alloys exposed to melting

  4. Contribution to the study of excited levels of 7Be obtained from the reaction 6Li (p, α)

    International Nuclear Information System (INIS)

    Beaumevieille, H.

    1964-05-01

    The interpretation of the results of the reaction 6 Li (p, α) in the energy range 100 keV to 3 MeV has been done with the next levels of 7 Be : 3/2- (5,9 MeV), 3/2+ (6,2 MeV), 5/2- (7,18 MeV) and a level the characteristics of which may be 1/2+ or 4 P (9,5 MeV). (author) [fr

  5. Electrolytes for lithium and lithium-ion batteries

    CERN Document Server

    Jow, T Richard; Borodin, Oleg; Ue, Makoto

    2014-01-01

    Electrolytes for Lithium and Lithium-ion Batteries provides a comprehensive overview of the scientific understanding and technological development of electrolyte materials in the last?several years. This book covers key electrolytes such as LiPF6 salt in mixed-carbonate solvents with additives for the state-of-the-art Li-ion batteries as well as new electrolyte materials developed recently that lay the foundation for future advances.?This book also reviews the characterization of electrolyte materials for their transport properties, structures, phase relationships, stabilities, and impurities.

  6. Extraction separation of lithium isotopes with crown-ethers

    International Nuclear Information System (INIS)

    Tsivadze, A.Yu.; Demin, S.V.; Levkin, A.V.; Zhilov, V.I.; Nikol'skij, S.F.; Knyazev, D.A.

    1990-01-01

    By the method of extraction chromatography lithium isotope separation coefficients are measured during chemical isotope exchange between lithium aquocomplex and its complex in chloroform with crown-ethers: benzo-15-crown-5, 15crown-5, dicyclohexano-18-crown-6 and dibenzo-18-crown-6. Lithium perchlorate and trichloroacetate are the salts extracted. Values of 6 Li/ 7 Li isotope separation are 1.0032-1.020

  7. Abuse resistant high rate lithium/thionyl chloride cells

    Energy Technology Data Exchange (ETDEWEB)

    Surprenant, J.; Snuggerud, D.

    1982-08-01

    A compact, disc shaped lithium/thionyl chloride cell has been developed by Altus Corporation. The cell has a 6 Amphr capacity and is capable of high rate discharge at high voltage. Discharge data is presented over the range of 0.07 to 1.1 Amperes. The cell is operable over the temperature range of -40/sup 0/C to +70/sup 0/C, and has a 10 year shelf life at 20/sup 0/C. Safety features allow the cells to withstand fire, puncture, shock, spin, forced discharge or forced charge without dangerous reactions.

  8. Abuse resistant high rate lithium/thionyl chloride cells

    Science.gov (United States)

    Surprenant, J.; Snuggerud, D.

    A compact, disk shaped lithium/thionyl chloride cell has been developed. The cell has a 6 Amphr capacity and is capable of high rate discharge at high voltage. Discharge data are presented over the range of 0.07 to 1.1 amperes. The cell is operable over the temperature range of -40 C to +70 C, and has a 10 year shelf life at 20 C. Safety features allow the cells to withstand fire, puncture, shock, spin, forced discharge or forced charge without dangerous reactions.

  9. Tritium recovery from lithium oxide pellets

    International Nuclear Information System (INIS)

    Bertone, P.C.; Jassby, D.L.

    1984-01-01

    The TFTR Lithium Blanket Module is an assembly containing 650 kg of lithium oxide that will be used to test the ability of neutronics codes to model the tritium breeding characteristics of limited-coverage breeding zones in a tokamak. It is required that tritium concentrations as low as 0.1 nCi/g bred in both metallic lithium samples and lithium oxide pellets be measured with an uncertainty not exceeding +- 6%. A tritium assay technique for the metallic samples which meets this criterion has been developed. Two assay techniques for the lithium oxide pellets are being investigated. In one, the pellets are heated in a flowing stream of hydrogen, while in the other, the pellets are dissolved in 12 M hydrochloric acid

  10. The ANC of 16O subthreshold states from 12C(6Li, d) reaction at energies near the barrier

    International Nuclear Information System (INIS)

    Adhikari, Sucheta; Basu, Chinmay

    2011-01-01

    The ANC of the 2 + (6.92 MeV) and 1 - (7.12 MeV) subthreshold states of 16 O have been extracted from the normalization of 12 C( 6 Li, d) angular distribution to a Finite Range Distorted Wave Born Approximation (FRDWBA) calculation. The theoretical analysis indicates a peripheral reaction and the extracted ANCs are not sensitive to the number of nodes in the bound state potential. The uncertainty from the entrance channel potential is minimized to 8% for the 6.92 and 11% for the 7.12 MeV state if the normalization is performed at the grazing angle. The uncertainty from the exit channel potential at the grazing angle is found to be 10% and 12% respectively for the 7.12 and 6.92 MeV states.

  11. Novel α-Oxoamide Advanced-Glycation Endproducts within the N6-Carboxymethyl Lysine and N6-Carboxyethyl Lysine Reaction Cascades.

    Science.gov (United States)

    Baldensperger, Tim; Jost, Tobias; Zipprich, Alexander; Glomb, Marcus A

    2018-02-28

    The highly reactive α-dicarbonyl compounds glyoxal and methylglyoxal are major precursors of posttranslational protein modifications in vivo. Model incubations of N 2 -t-Boc-lysine and either glyoxal or methylglyoxal were used to further elucidate the underlying mechanisms of the N 6 -carboxymethyl lysine and N 6 -carboxyethyl lysine reaction cascades. After independent synthesis of the authentic reference standards, we were able to detect N 6 -glyoxylyl lysine and N 6 -pyruvoyl lysine for the first time by HPLC-MS 2 analyses. These two novel amide advanced-glycation endproducts were exclusively formed under aerated conditions, suggesting that they were potent markers for oxidative stress. Analogous to the well-known Strecker degradation pathway, leading from amino acids to Strecker acids, the oxidation of an enaminol intermediate is suggested to be the key mechanistic step. A highly sensitive workup for the determination of AGEs in tissues was developed. In support of our hypothesis, the levels of N 6 -glyoxylyl lysine and N 6 -pyruvoyl lysine in rat livers indeed correlated with liver cirrhosis and aging.

  12. Phase space investigation of the lithium amide halides

    Energy Technology Data Exchange (ETDEWEB)

    Davies, Rosalind A. [Hydrogen Storage Chemistry Group, School of Chemistry, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Hydrogen and Fuel Cell Group, School of Chemical Engineering, University of Birmingham, Edgbaston B15 2TT (United Kingdom); Hewett, David R.; Korkiakoski, Emma [Hydrogen Storage Chemistry Group, School of Chemistry, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Thompson, Stephen P. [Diamond Light Source, Harwell Science and Innovation Campus, Didcot, Oxfordshire OX11 0QX (United Kingdom); Anderson, Paul A., E-mail: p.a.anderson@bham.ac.uk [Hydrogen Storage Chemistry Group, School of Chemistry, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom)

    2015-10-05

    Highlights: • The lower limits of halide incorporation in lithium amide have been investigated. • The only amide iodide stoichiometry observed was Li{sub 3}(NH{sub 2}){sub 2}I. • Solid solutions were observed in both the amide chloride and amide bromide systems. • A 46% reduction in chloride content resulted in a new phase: Li{sub 7}(NH{sub 2}){sub 6}Cl. • New low-chloride phase maintained improved H{sub 2} desorption properties of Li{sub 4}(NH{sub 2}){sub 3}Cl. - Abstract: An investigation has been carried out into the lower limits of halide incorporation in lithium amide (LiNH{sub 2}). It was found that the lithium amide iodide Li{sub 3}(NH{sub 2}){sub 2}I was unable to accommodate any variation in stoichiometry. In contrast, some variation in stoichiometry was accommodated in Li{sub 7}(NH{sub 2}){sub 6}Br, as shown by a decrease in unit cell volume when the bromide content was reduced. The amide chloride Li{sub 4}(NH{sub 2}){sub 3}Cl was found to adopt either a rhombohedral or a cubic structure depending on the reaction conditions. Reduction in chloride content generally resulted in a mixture of phases, but a new rhombohedral phase with the stoichiometry Li{sub 7}(NH{sub 2}){sub 6}Cl was observed. In comparison to LiNH{sub 2}, this new low-chloride phase exhibited similar improved hydrogen desorption properties as Li{sub 4}(NH{sub 2}){sub 3}Cl but with a much reduced weight penalty through addition of chloride. Attempts to dope lithium amide with fluoride ions have so far proved unsuccessful.

  13. Electrochemical Model for Ionic Liquid Electrolytes in Lithium Batteries

    International Nuclear Information System (INIS)

    Yoo, Kisoo; Deshpande, Anirudh; Banerjee, Soumik; Dutta, Prashanta

    2015-01-01

    ABSTRACT: Room temperature ionic liquids are considered as potential electrolytes for high performance and safe lithium batteries due to their very low vapor pressure and relatively wide electrochemical and thermal stability windows. Unlike organic electrolytes, ionic liquid electrolytes are molten salts at room temperature with dissociated cations and anions. These dissociated ions interfere with the transport of lithium ions in lithium battery. In this study, a mathematical model is developed for transport of ionic components to study the performance of ionic liquid based lithium batteries. The mathematical model is based on a univalent ternary electrolyte frequently encountered in ionic liquid electrolytes of lithium batteries. Owing to the very high concentration of components in ionic liquid, the transport of lithium ions is described by the mutual diffusion phenomena using Maxwell-Stefan diffusivities, which are obtained from atomistic simulation. The model is employed to study a lithium-ion battery where the electrolyte comprises ionic liquid with mppy + (N-methyl-N-propyl pyrrolidinium) cation and TFSI − (bis trifluoromethanesulfonyl imide) anion. For a moderate value of reaction rate constant, the electric performance results predicted by the model are in good agreement with experimental data. We also studied the effect of porosity and thickness of separator on the performance of lithium-ion battery using this model. Numerical results indicate that low rate of lithium ion transport causes lithium depleted zone in the porous cathode regions as the porosity decreases or the length of the separator increases. The lithium depleted region is responsible for lower specific capacity in lithium-ion cells. The model presented in this study can be used for design of optimal ionic liquid electrolytes for lithium-ion and lithium-air batteries

  14. Preliminary experimental study of liquid lithium water interaction

    International Nuclear Information System (INIS)

    You, X.M.; Tong, L.L.; Cao, X.W.

    2015-01-01

    Highlights: • Explosive reaction occurs when lithium temperature is over 300 °C. • The violence of liquid lithium water interaction increases with the initial temperature of liquid lithium. • The interaction is suppressed when the initial water temperature is above 70 °C. • Steam explosion is not ignorable in the risk assessment of liquid lithium water interaction. • Explosion strength of liquid lithium water interaction is evaluated by explosive yield. - Abstract: Liquid lithium is the best candidate for a material with low Z and low activation, and is one of the important choices for plasma facing materials in magnetic fusion devices. However, liquid lithium reacts violently with water under the conditions of loss of coolant accidents. The release of large heats and hydrogen could result in the dramatic increase of temperature and pressure. The lithium–water explosion has large effect on the safety of fusion devices, which is an important content for the safety assessment of fusion devices. As a preliminary investigation of liquid lithium water interaction, the test facility has been built and experiments have been conducted under different conditions. The initial temperature of lithium droplet ranged from 200 °C to 600 °C and water temperature was varied between 20 °C and 90 °C. Lithium droplets were released into the test section with excess water. The shape of lithium droplet and steam generated around the lithium were observed by the high speed camera. At the same time, the pressure and temperature in the test section were recorded during the violent interactions. The preliminary experimental results indicate that the initial temperature of lithium and water has an effect on the violence of liquid lithium water interaction.

  15. Preliminary experimental study of liquid lithium water interaction

    Energy Technology Data Exchange (ETDEWEB)

    You, X.M.; Tong, L.L.; Cao, X.W., E-mail: caoxuewu@sjtu.edu.cn

    2015-10-15

    Highlights: • Explosive reaction occurs when lithium temperature is over 300 °C. • The violence of liquid lithium water interaction increases with the initial temperature of liquid lithium. • The interaction is suppressed when the initial water temperature is above 70 °C. • Steam explosion is not ignorable in the risk assessment of liquid lithium water interaction. • Explosion strength of liquid lithium water interaction is evaluated by explosive yield. - Abstract: Liquid lithium is the best candidate for a material with low Z and low activation, and is one of the important choices for plasma facing materials in magnetic fusion devices. However, liquid lithium reacts violently with water under the conditions of loss of coolant accidents. The release of large heats and hydrogen could result in the dramatic increase of temperature and pressure. The lithium–water explosion has large effect on the safety of fusion devices, which is an important content for the safety assessment of fusion devices. As a preliminary investigation of liquid lithium water interaction, the test facility has been built and experiments have been conducted under different conditions. The initial temperature of lithium droplet ranged from 200 °C to 600 °C and water temperature was varied between 20 °C and 90 °C. Lithium droplets were released into the test section with excess water. The shape of lithium droplet and steam generated around the lithium were observed by the high speed camera. At the same time, the pressure and temperature in the test section were recorded during the violent interactions. The preliminary experimental results indicate that the initial temperature of lithium and water has an effect on the violence of liquid lithium water interaction.

  16. Deuterium retention in liquid lithium

    International Nuclear Information System (INIS)

    Baldwin, M.J.; Doerner, R.P.; Luckhardt, S.C.; Conn, R.W.

    2002-01-01

    Measurements of deuterium retention in samples of lithium exposed in the liquid state to deuterium plasma are reported. Retention was measured as a function of plasma ion dose in the range 6x10 19 -4x10 22 D atoms and exposure temperature between 523 and 673 K using thermal desorption spectrometry. The results are consistent with the full uptake of all deuterium ions incident on the liquid metal surface and are found to be independent of the temperature of the liquid lithium over the range explored. Full uptake, consistent with very low recycling, continues until the sample is volumetrically converted to lithium deuteride. This occurs for exposure temperatures where the gas pressure during exposure was both below and slightly above the corresponding decomposition pressure for LiD in Li. (author)

  17. Palladium-Catalyzed Cross-Coupling Reactions of Perfluoro Organic Compounds

    Directory of Open Access Journals (Sweden)

    Masato Ohashi

    2014-09-01

    Full Text Available In this review, we summarize our recent development of palladium(0-catalyzed cross-coupling reactions of perfluoro organic compounds with organometallic reagents. The oxidative addition of a C–F bond of tetrafluoroethylene (TFE to palladium(0 was promoted by the addition of lithium iodide, affording a trifluorovinyl palladium(II iodide. Based on this finding, the first palladium-catalyzed cross-coupling reaction of TFE with diarylzinc was developed in the presence of lithium iodide, affording α,β,β-trifluorostyrene derivatives in excellent yield. This coupling reaction was expanded to the novel Pd(0/PR3-catalyzed cross-coupling reaction of TFE with arylboronates. In this reaction, the trifluorovinyl palladium(II fluoride was a key reaction intermediate that required neither an extraneous base to enhance the reactivity of organoboronates nor a Lewis acid additive to promote the oxidative addition of a C–F bond. In addition, our strategy utilizing the synergetic effect of Pd(0 and lithium iodide could be applied to the C–F bond cleavage of unreactive hexafluorobenzene (C6F6, leading to the first Pd(0-catalyzed cross-coupling reaction of C6F6 with diarylzinc compounds.

  18. Cutaneous adverse drug reactions: clinical pattern and causative agents--a 6 year series from Chandigarh, India.

    Directory of Open Access Journals (Sweden)

    Sharma V

    2001-04-01

    Full Text Available AIM: To study the different clinical spectrum of cutaneous adverse drug reactions (ADR and to determine the causative drugs. MATERIALS & METHODS: A prospective, hospital based study was carried out over a period of 6 years recording various cutaneous ADR. RESULTS: A total of 500 patients with cutaneous ADR were enrolled in the study. The most common types of cutaneous ADR patterns were maculopapular rash (34.6%, fixed drug eruption (FDE (30% and urticaria (14%. The drugs most often incriminated for the various cutaneous ADR were antimicrobials (42.6%, anticonvulsants (22.2% and NSAIDs (18%. Anticonvulsants were implicated in 41.6% of maculopapular rashes. Sulfonamides accounted for 43.3% and NSAIDs for 30.7% of FDE. Urticaria was caused mainly by NSAIDs(24.3% and penicillins(20%. Anticonvulsants were responsible for 43.8% of life-threatening toxic epidermal necrolysis and Stevens Johnson syndrome. CONCLUSIONS: The clinical pattern and drugs causing cutaneous ADR are similar to those observed in other countries except for minor variations. Cutaneous ADR patterns and the drugs causing various reactions are changing every year, which may be due to the emergence of newer molecules and changing trends in the use of drugs.

  19. Differential cross section measurements for the 6Li(n,t)alpha reaction in the few MeV region

    Energy Technology Data Exchange (ETDEWEB)

    Devlin, Matthew J [Los Alamos National Laboratory; Taddeucci, Terence N [Los Alamos National Laboratory; Hale, Gerald M [Los Alamos National Laboratory; Haight, Robert C [Los Alamos National Laboratory; O' Donnell, Johhn M [Los Alamos National Laboratory

    2008-01-01

    New measured differential cross sections of tritons and alpha particles following the {sup 6}Li(n,t){alpha} reaction are reported for incident neutron energies between 0.2 and approximately 20 MeV. The neutrons were produced by spallation at the WNR facility at the Los Alamos Neutron Science CEnter (LANSCE), with the incident neutron energy determined by the time-of-flight method. Four E-{Delta}E telescopes were used at eight laboratory angles. These data have been incorporated into a prior R-matrix fit for the compound {sup 7}Li system, and result in an (n,t) reaction cross section that is 4% to 10% higher than previous evaluations in the 1-3 MeV incident neutron energy region.

  20. Exploring incomplete fusion fraction in 6,7Li induced nuclear reactions

    Science.gov (United States)

    Parkar, V. V.; Jha, V.; Kailas, S.

    2017-11-01

    We have included breakup effects explicitly to simultaneously calculate the measured cross-sections of the complete fusion, incomplete fusion, and total fusion for 6,7Li projectiles on various targets using the Continuum Discretized Coupled Channels method. The breakup absorption cross-sections obtained with different choices of short range imaginary potentials are utilized to evaluate the individual α-capture and d/t-capture cross-sections and compare with the measured data. It is interesting to note, while in case of 7Li projectile the cross-sections for triton-ICF/triton-capture is far more dominant than α-ICF/α-capture at all energies, similar behavior is not observed in case of 6Li projectile for the deuteron-ICF/deuteron-capture and α-ICF/α-capture. Both these observations are also corroborated by the experimental data for all the systems studied.

  1. Exploring incomplete fusion fraction in 6,7Li induced nuclear reactions

    Directory of Open Access Journals (Sweden)

    Parkar V. V.

    2017-01-01

    Full Text Available We have included breakup effects explicitly to simultaneously calculate the measured cross-sections of the complete fusion, incomplete fusion, and total fusion for 6,7Li projectiles on various targets using the Continuum Discretized Coupled Channels method. The breakup absorption cross-sections obtained with different choices of short range imaginary potentials are utilized to evaluate the individual α-capture and d/t-capture cross-sections and compare with the measured data. It is interesting to note, while in case of 7Li projectile the cross-sections for triton-ICF/triton-capture is far more dominant than α-ICF/α-capture at all energies, similar behavior is not observed in case of 6Li projectile for the deuteron-ICF/deuteron-capture and α-ICF/α-capture. Both these observations are also corroborated by the experimental data for all the systems studied.

  2. Nuclear excitation in the reaction 207Pb(μ-,ν6n)201Tl

    International Nuclear Information System (INIS)

    Budick, B.; Anigstein, R.; Kast, J.W.

    1982-01-01

    A probability of roughly 1% has been measured for the formation of the first excited state of 201 Tl following muon capture on 207 Pb. A probability of this magnitude for 6 neutron emission may indicate structure in the nuclear excitation function near 54 MeV. An alternative interpretation is provided by muon capture on a correlated np pair in analogy with pion absorption. (orig.)

  3. Factors controlling the redox potential of ZnCe6 in an engineered bacterioferritin photochemical 'reaction centre'.

    Science.gov (United States)

    Mahboob, Abdullah; Vassiliev, Serguei; Poddutoori, Prashanth K; van der Est, Art; Bruce, Doug

    2013-01-01

    Photosystem II (PSII) of photosynthesis has the unique ability to photochemically oxidize water. Recently an engineered bacterioferritin photochemical 'reaction centre' (BFR-RC) using a zinc chlorin pigment (ZnCe6) in place of its native heme has been shown to photo-oxidize bound manganese ions through a tyrosine residue, thus mimicking two of the key reactions on the electron donor side of PSII. To understand the mechanism of tyrosine oxidation in BFR-RCs, and explore the possibility of water oxidation in such a system we have built an atomic-level model of the BFR-RC using ONIOM methodology. We studied the influence of axial ligands and carboxyl groups on the oxidation potential of ZnCe6 using DFT theory, and finally calculated the shift of the redox potential of ZnCe6 in the BFR-RC protein using the multi-conformational molecular mechanics-Poisson-Boltzmann approach. According to our calculations, the redox potential for the first oxidation of ZnCe6 in the BRF-RC protein is only 0.57 V, too low to oxidize tyrosine. We suggest that the observed tyrosine oxidation in BRF-RC could be driven by the ZnCe6 di-cation. In order to increase the efficiency of tyrosine oxidation, and ultimately oxidize water, the first potential of ZnCe6 would have to attain a value in excess of 0.8 V. We discuss the possibilities for modifying the BFR-RC to achieve this goal.

  4. Scalable synthesis of interconnected porous silicon/carbon composites by the Rochow reaction as high-performance anodes of lithium ion batteries.

    Science.gov (United States)

    Zhang, Zailei; Wang, Yanhong; Ren, Wenfeng; Tan, Qiangqiang; Chen, Yunfa; Li, Hong; Zhong, Ziyi; Su, Fabing

    2014-05-12

    Despite the promising application of porous Si-based anodes in future Li ion batteries, the large-scale synthesis of these materials is still a great challenge. A scalable synthesis of porous Si materials is presented by the Rochow reaction, which is commonly used to produce organosilane monomers for synthesizing organosilane products in chemical industry. Commercial Si microparticles reacted with gas CH3 Cl over various Cu-based catalyst particles to substantially create macropores within the unreacted Si accompanying with carbon deposition to generate porous Si/C composites. Taking advantage of the interconnected porous structure and conductive carbon-coated layer after simple post treatment, these composites as anodes exhibit high reversible capacity and long cycle life. It is expected that by integrating the organosilane synthesis process and controlling reaction conditions, the manufacture of porous Si-based anodes on an industrial scale is highly possible. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Aqueous lithium air batteries

    Science.gov (United States)

    Visco, Steven J.; Nimon, Yevgeniy S.; De Jonghe, Lutgard C.; Petrov, Alexei; Goncharenko, Nikolay

    2017-05-23

    Aqueous Li/Air secondary battery cells are configurable to achieve high energy density and prolonged cycle life. The cells include a protected a lithium metal or alloy anode and an aqueous catholyte in a cathode compartment. The aqueous catholyte comprises an evaporative-loss resistant and/or polyprotic active compound or active agent that partakes in the discharge reaction and effectuates cathode capacity for discharge in the acidic region. This leads to improved performance including one or more of increased specific energy, improved stability on open circuit, and prolonged cycle life, as well as various methods, including a method of operating an aqueous Li/Air cell to simultaneously achieve improved energy density and prolonged cycle life.

  6. 8He-6He: a comparative study of electromagnetic fragmentation reactions

    International Nuclear Information System (INIS)

    Meister, M.; Richter A.; Schrieder, G.; Simon, H.; Markenroth, K.; Jonson, B.; Nyman, G.; Zhukov, M.V.

    2001-11-01

    Dissociation of a 227 MeV/u 8 He beam in a lead target has been studied in a kinematically complete experiment. The results are compared with similar data from the well-known halo nucleus 6 He. Coulomb-nuclear interference in the inelastic channel gives evidence for a I π = 1 - resonance in 8 He at E x =4.15 MeV. The deduced B(E1) value of 0.38±0.07 e 2 fm 2 indicates a uniform distribution of the four neutrons around the α particle core. (orig.)

  7. sup 8 He- sup 6 He a comparative study of electromagnetic fragmentation reactions

    CERN Document Server

    Meister, M; Aleksandrov, D.; Aumann, T.; Baumann, T.; Borge, M.J.G.; Chulkov, L.V.; Cortina-Gil, D.; Eberlein, B.; Elze, Th.W.; Emling, H.; Geissel, H.; Hellström, M.; Jonson, B.; Kratz, J.V.; Kulessa, R.; Leistenschneider, A.; Mukha, I.; Münzenberg, G.; Nickel, F.; Nilsson, T.; Nyman, G.; Pfützner, M.; Pribora, V.; Richter, A.; Riisager, K.; Scheidenberger, C.; Schrieder, G.; Simon, H.; Tengblad, O.; Zhukov, M.V.

    2002-01-01

    Dissociation of a 227 MeV/u sup 8 He beam in a lead target has been studied in a kinematically complete experiment. The results are compared with similar data from the well-known halo nucleus sup 6 He. Coulomb-nuclear interference in the inelastic channel gives evidence for a I suppi=1 sup - resonance in sup 8 He at E sub x =4.15 MeV. The deduced B(E1) value of 0.38+-0.07 e sup 2 fm sup 2 indicates a uniform distribution of the four neutrons around the alpha-particle core.

  8. High-efficiency technology for lithium isotope separation using an ionic-liquid impregnated organic membrane

    International Nuclear Information System (INIS)

    Hoshino, Tsuyoshi; Terai, Takayuki

    2011-01-01

    The tritium needed as a fuel for fusion reactors is produced by the neutron capture reaction of lithium-6 ( 6 Li) in tritium breeding materials. New lithium isotope separation technique using ionic-liquid impregnated organic membranes (Ionic-Liquid-i-OMs) have been developed. Lithium ions are able to move by electrodialysis through certain Ionic-Liquid-i-OMs between the cathode and the anode in lithium solutions. In this report, the effects of protection cover and membrane thickness on the durability of membrane and the efficiency of isotope separation were evaluated. In order to improve the durability of the Ionic-Liquid-i-OM, we developed highly-durable Ionic-Liquid-i-OM. Both surfaces of the Ionic-Liquid-i-OM were covered by a nafion 324 overcoat or a cation exchange membrane (SELEMION TM CMD) to prevent the outflow of the ionic liquid. It was observed that the durability of the Ionic-Liquid-i-OM was improved by a nafion 324 overcoat. On the other hand, the organic membrane selected was 1, 2 or 3 mm highly-porous Teflon film, in order to efficiently impregnate the ionic liquid. The 6 Li isotope separation factor by electrodialysis using highly-porous Teflon film of 3 mm thickness was larger than using that of 1 or 2 mm thickness.

  9. Halo Star Lithium Depletion

    International Nuclear Information System (INIS)

    Pinsonneault, M. H.; Walker, T. P.; Steigman, G.; Narayanan, Vijay K.

    1999-01-01

    The depletion of lithium during the pre-main-sequence and main-sequence phases of stellar evolution plays a crucial role in the comparison of the predictions of big bang nucleosynthesis with the abundances observed in halo stars. Previous work has indicated a wide range of possible depletion factors, ranging from minimal in standard (nonrotating) stellar models to as much as an order of magnitude in models that include rotational mixing. Recent progress in the study of the angular momentum evolution of low-mass stars permits the construction of theoretical models capable of reproducing the angular momentum evolution of low-mass open cluster stars. The distribution of initial angular momenta can be inferred from stellar rotation data in young open clusters. In this paper we report on the application of these models to the study of lithium depletion in main-sequence halo stars. A range of initial angular momenta produces a range of lithium depletion factors on the main sequence. Using the distribution of initial conditions inferred from young open clusters leads to a well-defined halo lithium plateau with modest scatter and a small population of outliers. The mass-dependent angular momentum loss law inferred from open cluster studies produces a nearly flat plateau, unlike previous models that exhibited a downward curvature for hotter temperatures in the 7Li-Teff plane. The overall depletion factor for the plateau stars is sensitive primarily to the solar initial angular momentum used in the calibration for the mixing diffusion coefficients. Uncertainties remain in the treatment of the internal angular momentum transport in the models, and the potential impact of these uncertainties on our results is discussed. The 6Li/7Li depletion ratio is also examined. We find that the dispersion in the plateau and the 6Li/7Li depletion ratio scale with the absolute 7Li depletion in the plateau, and we use observational data to set bounds on the 7Li depletion in main-sequence halo

  10. Synthesis of polysubstituted 4,5,6,7-tetrahydrofuro[2,3-c]pyridines by a novel multicomponent reaction.

    Science.gov (United States)

    Fayol, Aude; Zhu, Jieping

    2004-01-08

    [reaction: see text] A novel three-component synthesis of tetrahydrofuro[2,3-c]pyridines from readily accessible starting materials is described. Simply heating a toluene solution of an aminopentynoate, an aldehyde, and an alpha-isocyanoacetamide in the presence of ammonium chloride provided the 4,5,6,7-tetrahydrofuro[2,3-c]pyridines in good to excellent yield. The fused ring system is produced in this one-pot process by the concomitant formation of five chemical bonds.

  11. Study of astrophysically important resonant states in 26Si by the 28Si(4He,6He)26Si reaction

    Science.gov (United States)

    Kwon, Young Kwan; Lee, C. S.; Moon, J. Y.; Lee, J. H.; Kim, J. Y.; Kubono, S.; Iwasa, N.; Inafiki, K.; Yamaguchi, H.; He, J. J.; Saito, A.; Wakabayashi, Y.; Fukijawa, H.; Amadio, G.; Khiem, L. H.; Tanaka, M.; Chen, A.; Kato, S.

    PoS(NIC-IX)024 , b, H. Yamaguchia, J. J. Hea , A. Saitoa , Y. Wakabayashia, H. Fujikawaa, G. The emission of 1.809 MeV gamma-ray from the first excited state of 26 Mg followed by beta- decay of 26 Al in its ground state (denoted as 26 Alg.s. ) has been identified by gamma-ray telescopes such the Compton Gamma-Ray Observatory (CGRO) [1]. To resolve controversy over the pos- sible sources of the observational 1.809 MeV gamma-rays, one needs accurate knowledge of the production rate of 26 Al. The 25 Al(p,γ)26Si reaction which is the competition reaction for produc- tion of 26 Alg.s. is one of the important subjects to be investigated. In this work, the astrophysically important 26 Si states above the proton threshold were studied via the 28 Si(4 He,6 He)26 Si reaction. We have preformed an angular distribution measurement using the high resolution QDD spectro- graph (PA) at Center for Nuclear Study (CNS), University of Tokyo. The experimental results and data analysis will be presented.

  12. Disentangling effects of breakup coupling and incomplete fusion in 6Li + 232Th reaction

    International Nuclear Information System (INIS)

    Jha, V.; Parkar, V.V.; Mohanty, A.K.; Kailas, S.

    2014-01-01

    A component of fusion that is very important but quite difficult to evaluate is the incomplete fusion (ICF), in which only a part of the nucleus fuses with the target. ICF occurs together with the usual complete fusion (CF), in which the whole projectile fuses or all the projectile fragments after breakup fuse with the target nucleus. The ICF leads to the flux removal from the fusion channel and its calculation is essential for a comprehensive description of the fusion process. In the present work, a recently developed method of calculating the ICF cross-section (σ ICF ) is used in a novel way to disentangle the ICF effect on the fusion process from those due to breakup couplings. The total fusion cross-section σ TF and σ ICF for the 6 Li + 232 Th system are calculated at energies above and below the Coulomb barrier, where the measured fusion-fission data is available

  13. Basic technology for {sup 6}Li enrichment using an ionic-liquid impregnated organic membrane

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, Tsuyoshi, E-mail: hoshino.tsuyoshi@jaea.go.jp [Blanket Irradiation and Analysis Group, Fusion Research and Development Directorate, Japan Atomic Energy Agency, 4002, Narita-cho, Oarai-machi, Higashi Ibaraki-gun, Ibaraki 311-1393 (Japan); Terai, Takayuki [The Institute of Engineering Innovation and Department of Nuclear Engineering and Management School of Engineering, The University of Tokyo, 2-11-16 Yayoi, Bunkyo-ku, Tokyo 113-8656 (Japan)

    2011-10-01

    The tritium needed as a fuel for fusion reactors is produced by the neutron capture reaction of lithium-6 ({sup 6}Li) in tritium breeding materials. However, natural Li contains only about 7.6 at.% {sup 6}Li. In this paper, a new lithium isotope separation technique using an ionic-liquid impregnated organic membrane is proposed. In order to separate and concentrate lithium isotopes, only lithium ions are able to move through the membrane by electrodialysis between the cathode and the anode in lithium solutions. Preliminary experiments of lithium isotope separation were conducted using this phenomenon. Organic membranes impregnated with TMPA-TFSI and PP13-TFSI as ionic liquids were prepared, and the relationship between the {sup 6}Li separation coefficient and the applied electrodialytic conditions was evaluated using them. The results showed that the {sup 6}Li isotope separation coefficient in this method (about 1.1-1.4) was larger than that in the mercury amalgam method (about 1.06).

  14. Investigation of lithium-thionyl chloride battery safety hazards

    Science.gov (United States)

    Attia, A. I.; Gabriel, K. A.; Burns, R. P.

    1983-01-01

    In the ten years since the feasibility of a lithium-thionyl chloride cell was first recognized (1) remarkable progress has been made in hardware development. Cells as large as 16,000 Ah (2) and batteries of 10.8 MWh (3) have been demonstrated. In a low rate configuration, energy densities of 500 to 600 Wh/kg are easily achieved. Even in the absence of reported explosions, safety would be a concern for such a dense energetic package; the energy density of a lithium-thionyl chloride cell is approaching that of dynamite (924 Wh/kg). In fact explosions have occurred. In general the hazards associated with lithium-thionyl chloride batteries may be divided into four categories: Explosions as a result of an error in battery design. Very large cells were in prototype development prior to a full appreciation of the hazards of the system. It is possible that some of the remaining safety issues are related to cell design; Explosions as a result of external physical abuse such as cell incineration and puncture; Explosions due to short circuiting which could lead to thermal runaway reactions. These problems appear to have been solved by changes in the battery design (4); and Explosions due to abnormal electrical operation (i.e., charging (5) and overdischarging (6) and in partially or fully discharged cells on storage (7 and 8).

  15. Quasi-bound alpha resonant states populated by the {sup 12}C({sup 6}Li, d) reaction

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, M.R.D.; Borello-Lewin, T.; Miyake, H.; Horodynski-Matsushigue, L.B.; Duarte, J.L.M.; Rodrigues, C.L.; Souza, M.A. [Universidade de Sao Paulo (IF/USP), SP (Brazil). Inst. de Fisica; Cunsolo, A.; Cappuzzello, F.; Foti, A.; Agodi, C.; Cavallaro, M. [Istituto Nazionale di Fisica Nucleare (LNS/INFN), Catania (Italy). Lab. Nazionali del Sud; Ukita, G.M. [Universidade de Santo Amaro (UNISA), Sao Paulo, SP (Brazil). Faculdade de Psicologia

    2012-07-01

    Full text: The alpha cluster phenomenon in the light nuclei structure has been the subject of a long time investigation since the proposal of the Ikeda diagrams [1]. The main purpose of the research program in progress is the investigation of this phenomenon in (x{alpha}) and (x{alpha}+n) nuclei through the ({sup 6}Li, d) alpha transfer reaction [2-4]. Alpha resonant states around the (4{alpha}) threshold in the nucleus {sup 16}O are the focus of the present contribution. In fact, the importance of these resonances at the elements production in stars is recognized, as primarily pointed out by Hoyle in {sup 12}C [6]. The existence of a rotational band with the {alpha} +{sup 12} C (Hoyle) cluster state structure was recently demonstrated by Ohkubo and Hirabayashi [6]. In order to explore this region of interest, measurements of the {sup 12}C({sup 6}Li, d){sup 16}O reaction up to 17 MeV of excitation at an incident energy of 25.5 MeV, have been performed employing the Sao Paulo Pelletron-Enge Split-Pole facility and the nuclear emulsion detection technique (plates Fuji G6B, 50 {mu}m thick). Spectra associated with six scattering angles, from 5 deg to 29 deg in the laboratory frame, each one 50 cm along the focal surface, were measured. Several narrow resonances with a quasi-bound behavior embedded in the continuum were detected and the resolution of 25 keV allowed for the separation of doublets not resolved before [7,8]. The absolute cross sections and the respective deuteron angular distributions were determined and the analysis is in progress. [1] K. Ikeda et al., Prog. Theor. Phys. Suppl. E 68, 464 (1968); H. Horiuchi, K. Ikeda, and Y. Suzuki, ibid. 44, 225 (1978). [2] M.R.D.Rodrigues et al., in12th International Conference on Nuclear Reaction Mechanism, Varenna, Italy, edited by F. Cerutti and A. Ferrari , CERN Proceedings, 2010-2, pp. 331- 335. [3] T. Borello-Lewin et al., Proceedings of SOTANCP2, Brussels, Belgium 2010, edited by P. Descouvemount et al., Int. J

  16. Mechano-chemical synthesis K2MF6 (M = Mn, Ni) by cation-exchange reaction at room temperature

    Science.gov (United States)

    Rawat, Pooja; Nagarajan, Rajamani

    2018-02-01

    In order to establish the power of mechanochemistry to produce industrially important phosphors, synthesis of K2MnF6 has been attempted by the successive grinding reactions of manganese (II) acetate with ammonium fluoride and potassium fluoride. The progress of reaction was followed by ex-situ characterization after periodic intervals of time. Cubic symmetry of K2MnF6 was evident from its powder X-ray diffraction pattern which was refined successfully in cubic space group (Fm-3m) with a = 8.4658 (20) Å. Stretching and bending vibration modes of MnF62- octahedral units appeared at 740 and 482 cm-1 in the fourier transformed infrared spectrum. Bands at 405 and 652 cm-1 appeared in the Raman spectrum and they were finger-print positions of cubic K2MnF6. Other than the ligand to metal charge transfer transition at 242 nm, transitions from 4A2g to 4T1g, 4T2g and 2T2g of Mn4+-ion appeared at 352, 429, 474 and 569 nm in the UV-visible diffuse reflectance spectrum of the sample. Red emission due to Mn4+ was observed in the photoluminescence spectrum with a decay time of 0.22 ms. Following the success in forming cubic K2MnF6, this approach has been extended to synthesize cubic K2NiF6 at room temperature. All these results confirmed the susceptibility of acetate salts of transition metals belonging to first-row of the periodic table to facile fluorination at room temperature aided by mechanical forces.

  17. Superior lithium adsorption and required magnetic separation behavior of iron-doped lithium ion-sieves

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shulei; Zheng, Shili; Wang, Zheming; Cui, Wenwen; Zhang, Hailin; Yang, Liangrong; Zhang, Yi; Li, Ping

    2018-01-01

    The recent research on adsorption-based lithium recovery from lithium-containing solutions has been centred on adsorption capacity and separation of lithium ion-sieves powder from solutions. Herein, an effective iron-doped lithium titanium oxide (Fe-doped Li2TiO3) was synthesized by Fe-doping via solid state reactions followed by acid treatment to form iron-doped lithium ion-sieves (Fe/Ti-x(H)). The resulting solid powder displays both superior adsorption capacity of lithium and high separation efficiency of the adsorbent from the solutions. SEM imaging and BET surface area measurement results showed that at Fe doping levels x0.15, Fe-doping led to grain shrinkage as compared to Li2TiO3 and at the same time the BET surface area increased. The Fe/Ti-0.15(H) exhibited saturated magnetization values of 13.76 emu g-1, allowing effective separation of the material from solid suspensions through the use of a magnet. Consecutive magnetic separation results suggested that the Fe/Ti-0.15(H) powders could be applied at large-scale and continuously removed from LiOH solutions with separation efficiency of 96% or better. Lithium adsorption studies indicated that the equilibrium adsorption capacity of Fe/Ti-0.15(H) in LiOH 2 solutions (1.8 g L-1 Li, pH 12) reached 53.3 mg g-1 within 24 h, which was higher than that of pristine Li2TiO3 (50.5 mg g-1) without Fe doping. Competitive adsorption and regeneration results indicated that the Fe/Ti-0.15(H) possessed a high selectivity for Li with facile regeneration. Therefore, it could be expected that the iron-doped lithium ion-sieves have practical applicability potential for large scale lithium extraction and recovery from lithium-bearing solutions.

  18. Dynamical observation of lithium insertion/extraction reaction during charge-discharge processes in Li-ion batteries by in situ spatially resolved electron energy-loss spectroscopy.

    Science.gov (United States)

    Shimoyamada, Atsushi; Yamamoto, Kazuo; Yoshida, Ryuji; Kato, Takehisa; Iriyama, Yasutoshi; Hirayama, Tsukasa

    2015-12-01

    All-solid-state Li-ion batteries (LIBs) with solid electrolytes are expected to be the next generation devices to overcome serious issues facing conventional LIBs with liquid electrolytes. However, the large Li-ion transfer resistance at the electrode/solid-electrolyte interfaces causes low power density and prevents practical use. In-situ-formed negative electrodes prepared by decomposing the solid electrolyte Li(1+x+3z)Alx(Ti,Ge)(2-x)Si(3z)P(3-z)O12 (LASGTP) with an excess Li-ion insertion reaction are effective electrodes providing low Li-ion transfer resistance at the interfaces. Prior to our work, however, it had still been unclear how the negative electrodes were formed in the parent solid electrolytes. Here, we succeeded in dynamically visualizing the formation by in situ spatially resolved electron energy-loss spectroscopy in a transmission electron microscope mode (SR-TEM-EELS). The Li-ions were gradually inserted into the solid electrolyte region around 400 nm from the negative current-collector/solid-electrolyte interface in the charge process. Some of the ions were then extracted in the discharge process, and the rest were diffused such that the distribution was almost flat, resulting in the negative electrodes. The redox reaction of Ti(4+)/Ti(3+) in the solid electrolyte was also observed in situ during the Li insertion/extraction processes. The in situ SR-TEM-EELS revealed the mechanism of the electrochemical reaction in solid-state batteries. © The Author 2015. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  19. Photometric investigation of tungsten (6) reaction with monoazo compound based on pyrogallol

    International Nuclear Information System (INIS)

    Gambarov, D.G.; Gusejnov, A.G.

    1980-01-01

    The possibility has been studied to use a new monoazo compound 2,3,4-trihydroxy-4'-sulfoazobenzene (TSAB) for the photometric determination of tungsten in steels. The maximum yield of W(6) complex is observed in the interval from 0.3 NHCl to pH2. The maximum absorption of the complex is observed at 460 nm and that of reagent - at 380 nm. The complex coloring immediately develops and in stable for more than one day. Molar coefficient of complex extinctior equals 43000+-300. Tungsten concentration interval being determined in 0.3 N HCl is 10-140 μg/25 ml. Tungsten determination technique in chromium-nickel-tungsten and chromium-silicon-nickel steels is given. If steel samples contain Mo > 0.1 mg, Y > 0.2 mg, Zr > 1.0 mg, Fe > 0.03 mg and Si > 0.3 mg then it is necessary to separate Mo, Y and Zr beforehand. Fe and Si are respectively well camouflaged by ascorbic acid and EDTA

  20. Reactions of guanine with methyl chloride and methyl bromide: O6-methylation versus charge transfer complex formation

    Science.gov (United States)

    Shukla, P. K.; Mishra, P. C.; Suhai, S.

    Density functional theory (DFT) at the B3LYP/6-31+G* and B3LYP/AUG-cc-pVDZ levels was employed to study O6-methylation of guanine due to its reactions with methyl chloride and methyl bromide and to obtain explanation as to why the methyl halides cause genotoxicity and possess mutagenic and carcinogenic properties. Geometries of the various isolated species involved in the reactions, reactant complexes (RCs), and product complexes (PCs) were optimized in gas phase. Transition states connecting the reactant complexes with the product complexes were also optimized in gas phase at the same levels of theory. The reactant complexes, product complexes, and transition states were solvated in aqueous media using the polarizable continuum model (PCM) of the self-consistent reaction field theory. Zero-point energy (ZPE) correction to total energy and the corresponding thermal energy correction to enthalpy were made in each case. The reactant complexes of the keto form of guanine with methyl chloride and methyl bromide in water are appreciably more stable than the corresponding complexes involving the enol form of guanine. The nature of binding in the product complexes was found to be of the charge transfer type (O6mG+ · X-, X dbond Cl, Br). Binding of HCl, HBr, and H2O molecules to the PCs obtained with the keto form of guanine did not alter the positions of the halide anions in the PCs, and the charge transfer character of the PCs was also not modified due to this binding. Further, the complexes obtained due to the binding of HCl, HBr, and H2O molecules to the PCs had greater stability than the isolated PCs. The reaction barriers involved in the formation of PCs were found to be quite high (?50 kcal/mol). Mechanisms of genotoxicity, mutagenesis and carcinogenesis caused by the methyl halides appear to involve charge transfer-type complex formation. Thus the mechanisms of these processes involving the methyl halides appear to be quite different from those that involve the

  1. Lithium batteries; Les accumulateurs au lithium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    This workshop on lithium batteries is divided into 4 sections dealing with: the design and safety aspects, the cycling, the lithium intercalation and its modeling, and the electrolytes. These 4 sections represent 19 papers and are completed by a poster session which corresponds to 17 additional papers. (J.S.)

  2. Lithium batteries; Les accumulateurs au lithium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This workshop on lithium batteries is divided into 4 sections dealing with: the design and safety aspects, the cycling, the lithium intercalation and its modeling, and the electrolytes. These 4 sections represent 19 papers and are completed by a poster session which corresponds to 17 additional papers. (J.S.)

  3. Lithium use in batteries

    Science.gov (United States)

    Goonan, Thomas G.

    2012-01-01

    Lithium has a number of uses but one of the most valuable is as a component of high energy-density rechargeable lithium-ion batteries. Because of concerns over carbon dioxide footprint and increasing hydrocarbon fuel cost (reduced supply), lithium may become even more important in large batteries for powering all-electric and hybrid vehicles. It would take 1.4 to 3.0 kilograms of lithium equivalent (7.5 to 16.0 kilograms of lithium carbonate) to support a 40-mile trip in an electric vehicle before requiring recharge. This could create a large demand for lithium. Estimates of future lithium demand vary, based on numerous variables. Some of those variables include the potential for recycling, widespread public acceptance of electric vehicles, or the possibility of incentives for converting to lithium-ion-powered engines. Increased electric usage could cause electricity prices to increase. Because of reduced demand, hydrocarbon fuel prices would likely decrease, making hydrocarbon fuel more desirable. In 2009, 13 percent of worldwide lithium reserves, expressed in terms of contained lithium, were reported to be within hard rock mineral deposits, and 87 percent, within brine deposits. Most of the lithium recovered from brine came from Chile, with smaller amounts from China, Argentina, and the United States. Chile also has lithium mineral reserves, as does Australia. Another source of lithium is from recycled batteries. When lithium-ion batteries begin to power vehicles, it is expected that battery recycling rates will increase because vehicle battery recycling systems can be used to produce new lithium-ion batteries.

  4. Some safety considerations of liquid lithium as a fusion breeder material

    International Nuclear Information System (INIS)

    Jeppson, D.W.; Muhlestein, L.D.

    1986-01-01

    Test results and conclusions are presented for the reaction of steam with a high temperature lithium pool and for the reaction of high temperature lithium spray with a nitrogen atmosphere. The reactions are characterized and evaluated in regard to the potential for mobilization of radioactive species associated with the liquid breeder under postulated fusion reactor accident conditions. These evaluations include measured lithium temperature responses, atmosphere temperature and pressure responses, gas consumption and generation, aerosol quantities and particle size characterization, and potentially radioactive species releases. Conclusions are made as to the consequences of these safety considerations for the use of lithium as a fusion reactor breeder material

  5. Safety considerations of lithium lead alloy as a fusion reactor breeding material

    International Nuclear Information System (INIS)

    Jeppson, D.W.; Muhlestein, L.D.

    1985-01-01

    Test results and conclusions are presented for lithium lead alloy interactions with various gas atmospheres, concrete and potential reactor coolants. The reactions are characterized to evaluate the potential of volatilizing and transporting radioactive species associated with the liquid breeder under postulated fusion reactor accident conditions. The safety concerns identified for lithium lead alloy reactions with the above materials are compared to those previously identified for a reference fusion breeder material, liquid lithium. Conclusions made from this comparison are also included

  6. Transparent plastic scintillators for neutron detection based on lithium salicylate

    International Nuclear Information System (INIS)

    Mabe, Andrew N.; Glenn, Andrew M.; Carman, M. Leslie; Zaitseva, Natalia P.; Payne, Stephen A.

    2016-01-01

    Transparent plastic scintillators with pulse shape discrimination containing "6Li salicylate have been synthesized by bulk polymerization with a maximum "6Li loading of 0.40 wt%. Photoluminescence and scintillation responses to gamma-rays and neutrons are reported herein. Plastics containing "6Li salicylate exhibit higher light yields and permit a higher loading of "6Li as compared to previously reported plastics based on lithium 3-phenylsalicylate. However, pulse shape discrimination performance is reduced in lithium salicylate plastics due to the requirement of adding more nonaromatic monomers to the polymer matrix as compared to those based on lithium 3-phenylsalicylate. Reduction in light yield and pulse shape discrimination performance in lithium-loaded plastics as compared to pulse shape discrimination plastics without lithium is interpreted in terms of energy transfer interference by the aromatic lithium salts. - Highlights: • Plastic scintillator with 0.4% "6Li loading is reported using lithium salicylate. • Influence of lithium salts on the scintillation mechanism is explored. • New lithium-loaded scintillator provides improved light yield and reduced cost.

  7. Direct observation of lithium polysulfides in lithium-sulfur batteries using operando X-ray diffraction

    Science.gov (United States)

    Conder, Joanna; Bouchet, Renaud; Trabesinger, Sigita; Marino, Cyril; Gubler, Lorenz; Villevieille, Claire

    2017-06-01

    In the on going quest towards lithium-battery chemistries beyond the lithium-ion technology, the lithium-sulfur system is emerging as one of the most promising candidates. The major outstanding challenge on the route to commercialization is controlling the so-called polysulfide shuttle, which is responsible for the poor cycling efficiency of the current generation of lithium-sulfur batteries. However, the mechanistic understanding of the reactions underlying the polysulfide shuttle is still incomplete. Here we report the direct observation of lithium polysulfides in a lithium-sulfur cell during operation by means of operando X-ray diffraction. We identify signatures of polysulfides adsorbed on the surface of a glass-fibre separator and monitor their evolution during cycling. Furthermore, we demonstrate that the adsorption of the polysulfides onto SiO2 can be harnessed for buffering the polysulfide redox shuttle. The use of fumed silica as an electrolyte additive therefore significantly improves the specific charge and Coulombic efficiency of lithium-sulfur batteries.

  8. Method for fabricating carbon/lithium-ion electrode for rechargeable lithium cell

    Science.gov (United States)

    Huang, Chen-Kuo (Inventor); Surampudi, Subbarao (Inventor); Attia, Alan I. (Inventor); Halpert, Gerald (Inventor)

    1995-01-01

    The method includes steps for forming a carbon electrode composed of graphitic carbon particles adhered by an ethylene propylene diene monomer binder. An effective binder composition is disclosed for achieving a carbon electrode capable of subsequent intercalation by lithium ions. The method also includes steps for reacting the carbon electrode with lithium ions to incorporate lithium ions into graphitic carbon particles of the electrode. An electrical current is repeatedly applied to the carbon electrode to initially cause a surface reaction between the lithium ions and to the carbon and subsequently cause intercalation of the lithium ions into crystalline layers of the graphitic carbon particles. With repeated application of the electrical current, intercalation is achieved to near a theoretical maximum. Two differing multi-stage intercalation processes are disclosed. In the first, a fixed current is reapplied. In the second, a high current is initially applied, followed by a single subsequent lower current stage. Resulting carbon/lithium-ion electrodes are well suited for use as an anode in a reversible, ambient temperature, lithium cell.

  9. Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, A.B. Jr.

    1976-09-01

    Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO/sub 2/) and lithium silicate (Li/sub 2/SiO/sub 3/) by the reaction: Li/sup 6/ + n ..-->.. /sup 4/He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100/sup 0/C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T/sub 2/), while in laboratory extractions (300-1300/sup 0/C), the tritium appeared primarily in the condensible form (HTO and T/sub 2/O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H/sub 2/O, CO/sub 2/, CO, O/sub 2/, H/sub 2/, NO, SO/sub 2/, SiF/sub 4/ and traces of hydrocarbons.

  10. Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

    International Nuclear Information System (INIS)

    Johnson, A.B. Jr.

    1976-09-01

    Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO 2 ) and lithium silicate (Li 2 SiO 3 ) by the reaction: Li 6 + n → 4 He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100 0 C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T 2 ), while in laboratory extractions (300-1300 0 C), the tritium appeared primarily in the condensible form (HTO and T 2 O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H 2 O, CO 2 , CO, O 2 , H 2 , NO, SO 2 , SiF 4 and traces of hydrocarbons

  11. Study of the gamma spectra emitted in a nuclear reaction - Measurement of the half-lives of the levels 6.13 MeV, 6.92 MeV and 7.12 MeV of 16O

    International Nuclear Information System (INIS)

    Leccia, F.

    1967-01-01

    When the energy shifts of the gamma spectrum released during a nuclear reaction are important compared with the detector resolution, the comparison of the experimental spectrum with theoretical spectra allows us to determine the half-life of the initial state of the transition. The calculation of the experimental spectrum implies to know the slowing-down of the recoil nucleus in the matter in order to take into account the Doppler effect. For recoil energies in the range of the MeV and for solid media, the Lindhard theory agrees well with experimental data. The phenomenon of deflection which appears at very low energies must be taken into account by restraining the measurement domain. By choosing an adequate media we can measure half-lives in the domain 1 and 100 fs without needing to take into account deflection effects. We have measured the half-life of the first 3 energy levels of 16 O (6.135 MeV, 6.923 MeV and 7.121 MeV), these levels are reached through the reaction 19 F(p,αγ) 16 O with proton incident energies ranging from 0.872 MeV to 2.42 MeV. We have used a coaxial germanium semi-conductor with lithium additions that was connected to an amplification line of Ortec type. 2 kinds of target have been used: calcium fluoride and copper fluoride evaporated on tantalum support. We have obtained the following values for the half-life: (16±4) fs for the 6.923 MeV level, (18±4) fs for the 7.121 MeV level, and for the 6.135 MeV we can only give a lower limit since the gamma decay occurs when the nucleus is at rest τ > 200 fs

  12. Polyethylene Glycol (PEG-400: An Efficient and Recyclable Reaction Medium for the Synthesis of Pyrazolo[3,4-b]pyridin-6(7H-one Derivatives

    Directory of Open Access Journals (Sweden)

    Deming Wang

    2013-10-01

    Full Text Available A mild and efficient synthesis of pyrazolo[3,4-b]pyridine-6(7H-one derivatives via a three-component reaction of an aldehyde, Meldrum’s acid and 3-methyl-1H-pyrazol-5-amine using recyclable polyethylene glycol (PEG-400 as a reaction medium is described. This method has the advantages of accessible starting materials, good yields, mild reaction conditions and begin environmentally friendly.

  13. Pigment organization and their interactions in reaction centers of photosystem II: optical spectroscopy at 6 K of reaction centers with modified pheophytin composition.

    Science.gov (United States)

    Germano, M; Shkuropatov, A Y; Permentier, H; de Wijn, R; Hoff, A J; Shuvalov, V A; van Gorkom, H J

    2001-09-25

    Photosystem II reaction centers (RC) with selectively exchanged pheophytin (Pheo) molecules as described in [Germano, M., Shkuropatov, A. Ya., Permentier, H., Khatypov, R. A., Shuvalov, V. A., Hoff, A. J., and van Gorkom, H. J. (2000) Photosynth. Res. 64, 189-198] were studied by low-temperature absorption, linear and circular dichroism, and triplet-minus-singlet absorption-difference spectroscopy. The ratio of extinction coefficients epsilon(Pheo)/epsilon(Chl) for Q(Y) absorption in the RC is approximately 0.40 at 6 K and approximately 0.45 at room temperature. The presence of 2 beta-carotenes, one parallel and one perpendicular to the membrane plane, is confirmed. Absorption at 670 nm is due to the perpendicular Q(Y) transitions of the two peripheral chlorophylls (Chl) and not to either Pheo. The "core" pigments, two Pheo and four Chl absorb in the 676-685 nm range. Delocalized excited states as predicted by the "multimer model" are seen in the active branch. The inactive Pheo and the nearby Chl, however, mainly contribute localized transitions at 676 and 680 nm, respectively, although large CD changes indicate that exciton interactions are present on both branches. Replacement of the active Pheo prevents triplet formation, causes an LD increase at 676 and 681 nm, a blue-shift of 680 nm absorbance, and a bleach of the 685 nm exciton band. The triplet state is mainly localized on the Chl corresponding to B(A) in purple bacteria. Both Pheo Q(Y) transitions are oriented out of the membrane plane. Their Q(X) transitions are parallel to that plane, so that the Pheos in PSII are structurally similar to their homologues in purple bacteria.

  14. Electron-stimulated desorption of lithium ions from lithium halide thin films

    International Nuclear Information System (INIS)

    Markowski, Leszek

    2007-01-01

    Electron-stimulated desorption of positive lithium ions from thin layers of lithium halides deposited onto Si(1 1 1) are investigated by the time-of-flight technique. The determined values of isotope effect of the lithium ( 6 Li + / 7 Li + ) are 1.60 ± 0.04, 1.466 ± 0.007, 1.282 ± 0.004, 1.36 ± 0.01 and 1.33 ± 0.01 for LiH, LiF, LiCl, LiBr and LiI, respectively. The observed most probable kinetic energies of 7 Li + are 1.0, 1.9, 1.1, 0.9 and 0.9 eV for LiH, LiF, LiCl, LiBr and LiI, respectively, and seem to be independent of the halide component mass. The values of lithium ion emission yield, lithium kinetic energy and lithium isotope effect suggest that the lattice relaxation is only important in the lithium ion desorption process from the LiH system. In view of possible mechanisms and processes involved into lithium ion desorption the obtained results indicate that for LiH, LiCl, LiBr and LiI the ions desorb in a rather classical way. However, for LiF, ion desorption has a more quantum character and the modified wave packet squeezing model has to be taken into account

  15. The structural, microhardness and thermal properties of a semiorganic NLO crystal: Lithium paranitrophenolate trihydrate (NO2-C6H4-OLi.3H2O)

    International Nuclear Information System (INIS)

    Boaz, B. Milton; Raman, P. Santhana; Raja, S. Xavier Jesu; Das, S. Jerome

    2005-01-01

    The crystallographic parameters, morphology, microhardness anisotropy and thermal properties including differential thermal analysis (DTA), thermo gravimetric analysis (TGA) of a new nonlinear optical material lithium paranitrophenolate trihydrate (NPLi.3H 2 O) are reported. The single crystals of NPLi.3H 2 O show effective phase matchable second harmonic generation properties for frequency conversion. Optically clear single crystals having dimensions up to 12 mm x 8 mm x 4 mm have been grown successfully within a period of 60 days by isothermal solvent evaporation technique. The title compound crystallizes in monoclinic system with space group Pa. Microhardness measurement on different planes verifies the hardness anisotropy and thermal studies reveal good thermal stability of the material. The NLO property of the crystal is verified by employing Kurtz powder test. The crystal has a wide range of optical transparency from 400 nm to 1500 nm

  16. Study of breakup and transfer of weakly bound nucleus 6Li to explore the low energy reaction dynamics

    Science.gov (United States)

    Zhang, G. L.; Zhang, G. X.; Hu, S. P.; Zhang, H. Q.; Gomes, P. R. S.; Lubian, J.; Guo, C. L.; Wu, X. G.; Yang, J. C.; Zheng, Y.; Li, C. B.; He, C. Y.; Zhong, J.; Li, G. S.; Yao, Y. J.; Guo, M. F.; Sun, H. B.; Valiente-Dobòn, J. J.; Goasduff, A.; Siciliano, M.; Galtarosa, F.; Francesco, R.; Testov, D.; Mengoni, D.; Bazzacco, D.; John, P. R.; Qu, W. W.; Wang, F.; Zheng, L.; Yu, L.; Chen, Q. M.; Luo, P. W.; Li, H. W.; Wu, Y. H.; Zhou, W. K.; Zhu, B. J.; Li, E. T.; Hao, X.

    2017-11-01

    Investigation of the breakup and transfer effect of weakly bound nuclei on the fusion process has been an interesting research topic in the past several years. However, owing to the low intensities of the presently available radioactive ion beam (RIB), it is difficult to clearly explore the reaction mechanisms of nuclear systems with unstable nuclei. In comparison with RIB, the beam intensities of stable weakly bound nuclei such as 6,7Li and 9Be, which have significant breakup probability, are orders of magnitude higher. Precise fusion measurements have already been performed with those stable weakly bound nuclei, and the effect of breakup of those nuclei on the fusion process has been extensively studied. Those nuclei indicated large production cross sections for particles other than the α + x breakup. The particles are originated from non-capture breakup (NCBU), incomplete fusion (ICF) and transfer processes. However, the conclusion of reaction dynamics was not clear and has the contradiction. In our previous experiments we have performed 6Li+96Zr and 154Sm at HI-13 Tandem accelerator of China Institute of Atomic Energy (CIAE) by using HPGe array. It is shown that there is a small complete fusion (CF) suppression on medium-mass target nucleus 96Zr different from about 35% suppression on heavier target nucleus 154Sm at near-barrier energies. It seems that the CF suppression factor depends on the charge of target nuclei. We also observed one neutron transfer process. However, the experimental data are scarce for medium-mass target nuclei. In order to have a proper understanding of the influence of breakup and transfer of weakly bound projectiles on the fusion process, we performed the 6Li+89Y experiment with incident energies of 22 MeV and 34 MeV on Galileo array in cooperation with Si-ball EUCLIDES at Legnaro National Laboratory (LNL) in Italy. Using particle-particle and particle-γ coincidences, the different reaction mechanisms can be clearly explored.

  17. Hypernuclear production cross section in the reaction of 6Li + 12C at 2A GeV

    Directory of Open Access Journals (Sweden)

    C. Rappold

    2015-07-01

    Full Text Available Hypernuclear production cross sections have been deduced for the first time with induced reaction of heavy ion beam on fixed target and by means of the invariant mass method by the HypHI Collaboration exploiting the reaction of 6Li + 12C at 2A GeV or sNN=2.70 GeV. A production cross section of 3.9±1.4 μb for 3ΛH and of 3.1±1.0 μb for 4ΛH respectively in the projectile rapidity region was inferred as well as the total production cross section of the Λ hyperon was measured and found to be equal to 1.7±0.8 mb. A global fit based on a Bayesian approach was performed in order to include and propagate statistical and systematic uncertainties. Production ratios of 3ΛH/4ΛH, 3ΛH/Λ and 4ΛH/Λ were included in the inference procedure. The strangeness population factors S3 and S4 of 3ΛH and 4ΛH respectively were extracted. In addition, the multiplicities of the Λ hyperon, 3ΛH, and 4ΛH together with the rapidity and transversal momentum density distributions of the observed hypernuclei were extracted and reported.

  18. EQ6, a computer program for reaction path modeling of aqueous geochemical systems: Theoretical manual, user`s guide, and related documentation (Version 7.0); Part 4

    Energy Technology Data Exchange (ETDEWEB)

    Wolery, T.J.; Daveler, S.A.

    1992-10-09

    EQ6 is a FORTRAN computer program in the EQ3/6 software package (Wolery, 1979). It calculates reaction paths (chemical evolution) in reacting water-rock and water-rock-waste systems. Speciation in aqueous solution is an integral part of these calculations. EQ6 computes models of titration processes (including fluid mixing), irreversible reaction in closed systems, irreversible reaction in some simple kinds of open systems, and heating or cooling processes, as well as solve ``single-point`` thermodynamic equilibrium problems. A reaction path calculation normally involves a sequence of thermodynamic equilibrium calculations. Chemical evolution is driven by a set of irreversible reactions (i.e., reactions out of equilibrium) and/or changes in temperature and/or pressure. These irreversible reactions usually represent the dissolution or precipitation of minerals or other solids. The code computes the appearance and disappearance of phases in solubility equilibrium with the water. It finds the identities of these phases automatically. The user may specify which potential phases are allowed to form and which are not. There is an option to fix the fugacities of specified gas species, simulating contact with a large external reservoir. Rate laws for irreversible reactions may be either relative rates or actual rates. If any actual rates are used, the calculation has a time frame. Several forms for actual rate laws are programmed into the code. EQ6 is presently able to model both mineral dissolution and growth kinetics.

  19. EQ6, a computer program for reaction path modeling of aqueous geochemical systems: Theoretical manual, user's guide, and related documentation (Version 7.0)

    International Nuclear Information System (INIS)

    Wolery, T.J.; Daveler, S.A.

    1992-01-01

    EQ6 is a FORTRAN computer program in the EQ3/6 software package (Wolery, 1979). It calculates reaction paths (chemical evolution) in reacting water-rock and water-rock-waste systems. Speciation in aqueous solution is an integral part of these calculations. EQ6 computes models of titration processes (including fluid mixing), irreversible reaction in closed systems, irreversible reaction in some simple kinds of open systems, and heating or cooling processes, as well as solve ''single-point'' thermodynamic equilibrium problems. A reaction path calculation normally involves a sequence of thermodynamic equilibrium calculations. Chemical evolution is driven by a set of irreversible reactions (i.e., reactions out of equilibrium) and/or changes in temperature and/or pressure. These irreversible reactions usually represent the dissolution or precipitation of minerals or other solids. The code computes the appearance and disappearance of phases in solubility equilibrium with the water. It finds the identities of these phases automatically. The user may specify which potential phases are allowed to form and which are not. There is an option to fix the fugacities of specified gas species, simulating contact with a large external reservoir. Rate laws for irreversible reactions may be either relative rates or actual rates. If any actual rates are used, the calculation has a time frame. Several forms for actual rate laws are programmed into the code. EQ6 is presently able to model both mineral dissolution and growth kinetics

  20. Reaction of xenon difluoride with certain rare earth fluorocomplexes of Cs/sub 3/MF/sub 6/ composition

    Energy Technology Data Exchange (ETDEWEB)

    Kiselev, Yu.M.; Goryachenkov, S.A.; Martynenko, L.I. (Moskovskij Gosudarstvennyj Univ. (USSR))

    1983-05-01

    By thermographic method in a specially manufactured nickel cell for thermal analysis the reaction of XeF/sub 2/ with Cs/sub 3/M/sup 3/F/sub 6/ (M=Ce, Pr, Tb, Nd, Dy, Er) is studied. Temperatures of thermal effects (Ts) corresponding to Cs/sub 3/M/sup 4/F/sub 7/ formation regularly increase in the series Ce-Tb-Pr-Dy-Nd (115-382 deg C). Cs/sub 3/M/sup 4/F/sub 7/ compounds are characterized by the methods of chemical analysis, X-ray diffraction and oscillating spectroscopy (IR and CS spectroscopy). Experimental data are best of all interpreted on assumption of the presence in Cs/sub 3/M/sup 4/F/sub 7/ crystals statistically oriented MF/sub 7/ fragments of the Dsub(5h) symmetry.

  1. Rapid synthesis of graphitic carbon nitride powders by metathesis reaction between CaCN2 and C2Cl6

    International Nuclear Information System (INIS)

    Pang Linlin; Bi Jianqiang; Bai Yujun; Qi Yongxin; Zhu Huiling; Wang Chengguo; Wu Jiwei; Lu Chengwei

    2008-01-01

    Carbon nitride powders were rapidly synthesized at low temperature via the chemical metathesis reaction between CaCN 2 and C 2 Cl 6 . X-ray diffraction results confirm the formation of crystalline graphitic carbon nitride. Besides the dominant morphology of nanoparticles, flakes, nanorods, hollow and solid spheres can be observed by transmission electron microscopy. The absorption peaks of C-N, C=N and s-triazine rings, as well as the absence of C≡N peak in the infrared spectra, further verify the formation of graphite-like sp 2 -bonded structure with planar networks. Elemental analysis gives an atomic ratio of N/C around 0.3. X-ray photoelectron spectra exhibit the existence of chemical bonding between C and N

  2. Study of the {sup 6}Li + p → {sup 3}He + {sup 4}He reaction in inverse kinematics

    Energy Technology Data Exchange (ETDEWEB)

    Betsou, C.; Pakou, A.; Aslanoglou, X.; Nicolis, N.G.; Sgouros, O.; Soukeras, V. [The University of Ioannina, Department of Physics and HINP, Ioannina (Greece); Cappuzzello, F. [Laboratori Nazionali del Sud, INFN, Catania (Italy); Universita di Catania, Dipartimento di Fisica e Astronomia, Catania (Italy); Acosta, L. [Universidad Nacional Autonoma de Mexico, Instituto de Fisica, Mexico Distrito Federal (Mexico); INFN, Catania (Italy); Agodi, C.; Carbone, D.; Cavallaro, M.; Di Pietro, A.; Fernandez-Garcia, J.P.; Figuera, P.; Fisichella, M. [Laboratori Nazionali del Sud, INFN, Catania (Italy); Foti, A. [Universita di Catania, Dipartimento di Fisica e Astronomia, Catania (Italy); INFN, Catania (Italy); Keeley, N. [National Centre for Nuclear Research, Otwock (Poland); Marquinez-Duran, G.; Martel, I. [Universidad de Huelva, Departamento de Fisica Aplicada, Huelva (Spain); Mazzocco, M.; Strano, E.; Torresi, D. [Universita di Padova, Departimento di Fisica e Astronomia, Padova (Italy); INFN, Padova (Italy); Pierroutsakou, D. [INFN, Napoli (Italy); Rusek, K. [University of Warsaw, Heavy Ion Laboratory, Warsaw (Poland); Stiliaris, E. [University of Athens, Institute of Accelerating Systems and Applications and Department of Physics, Athens (Greece)

    2015-07-15

    Angular distribution measurements were performed for the {sup 6}Li + p → {sup 3}He + {sup 4}He reaction in inverse kinematics at incident energies of 2.7, 3.3, 4.2 and 4.8 MeV/u. The detection of both recoils ({sup 3}He and {sup 4}He) over the laboratory angle range θ{sub lab} = 16 {sup circle} to 34 {sup circle} allowed the determination of the angular distribution over a wide angular range in the center-of-mass frame (θ{sub c.m.} ∝ 40 {sup circle} to 140 {sup circle}). The results clarify inconsistencies between existing data sets and are consistent with compound nucleus model calculations. (orig.)

  3. Cascade Wittig reaction-double Claisen and Cope rearrangements: one-pot synthesis of diprenylated coumarins gravelliferone, balsamiferone, and 6,8-diprenylumbelliferone

    Digital Repository Service at National Institute of Oceanography (India)

    Patre, R.E.; Shet, J.B.; Parameswaran, P.S.; Tilve, S.G.

    A cascade Wittig reaction-double Claisen and Cope rearrangements has been employed for a one-pot synthesis of diprenylated coumarins gravelliferone, balsamiferone, and 6,8-diprenylumbelliferone from a common precursor 2,4-diprenyloxybenzaldehyde...

  4. Molecular modeling study of lithium isotopic separation by crown-ethers in ethanol

    International Nuclear Information System (INIS)

    Dehez, F.

    2002-01-01

    The isotopic separation of lithium ion isotopes is studied at the CEA in Pierrelatte using a liquid chromatography technique. Exchange systems are composed by crown-ethers grafted on silica (12C4, 15C5, B15C5, DB15C5, 18C6, B18C6). Lithium is introduced as a salt melted in ethanol. This work concerns the theoretical study of lithium isotopic exchange reactions with those systems. After a brief presentation of isotope separation techniques and isotopic effects (Chap.I), we describe the methods of theoretical chemistry used in this work (Chap. II). In chapter III, we test AM1 and PM3 semi-empirical methods for the treatment of Li + /crown-ether species. Then, we calculate isotopic separation factors via ab initio and semi-empirical calculations for the exchange reactions in vacuum. The different crown-ethers are considered with and without graftings arms. Studies of exchange reactions in ethanol are presented in chapter IV. First, each species of the reaction are solvated by a few ethanol molecules. Isotopic separation factors calculated show a large effect of the solvent on the exchange reaction. The effect of the grafting arm has been investigated using hybrid quantum mechanics/molecular mechanics (QM/MM) molecular dynamics for species with the 12C4. Trajectories have been generated successively with 7 Li and 6 Li. Atomic velocity autocorrelation functions have allowed the access to vibrational frequencies necessary to calculate isotopic separation factors. The last chapter is devoted to methodological developments made during this Ph.D. We propose an approach to treat long range electrostatic interactions in hybrid QM/MM method, relying on a lattice summation technique. (author) [fr

  5. Isolation and Characterization of the 2,2'-Azinobis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) Radical Cation-Scavenging Reaction Products of Arbutin.

    Science.gov (United States)

    Tai, Akihiro; Ohno, Asako; Ito, Hideyuki

    2016-09-28

    Arbutin, a glucoside of hydroquinone, has shown strong 2,2'-azinobis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical cation-scavenging activity, especially in reaction stoichiometry. This study investigated the reaction mechanism of arbutin against ABTS radical cation that caused high stoichiometry of arbutin in an ABTS radical cation-scavenging assay. HPLC analysis of the reaction mixture of arbutin and ABTS radical cation indicated the existence of two reaction products. The two reaction products were purified and identified to be a covalent adduct of arbutin with an ABTS degradation fragment and 3-ethyl-6-sulfonate benzothiazolone. A time-course study of the radical-scavenging reactions of arbutin and the two reaction products suggested that one molecule of arbutin scavenges three ABTS radical cation molecules to generate an arbutin-ABTS fragment adduct as a final reaction product. The results suggest that one molecule of arbutin reduced two ABTS radical cation molecules to ABTS and then cleaved the third ABTS radical cation molecule to generate two products, an arbutin-ABTS fragment adduct and 3-ethyl-6-sulfonate benzothiazolone.

  6. Investigation of Enhanced Leaching of Lithium from α-Spodumene Using Hydrofluoric and Sulfuric Acid

    Directory of Open Access Journals (Sweden)

    Hui Guo

    2017-10-01

    Full Text Available An effective method using hydrofluoric and sulfuric acid was proposed to enhance the leaching of lithium from α-spodumene, without calcination that is subjected to 1000 °C for phase transformation. The thermodynamic feasibility of the reactions was firstly verified. Dissolution conditions were tested to maximize the leaching efficiency of lithium and with efficient utilization of hydrofluoric acid (HF served as evaluation criteria. The results showed that 96% of lithium could be transferred into lixivium with an ore/HF/H2SO4 ratio of 1:3:2 (g/mL/mL, at 100 °C for 3 h. Due to the fact that HF molecules were the main reaction form, the dissolution behaviors were theoretically represented and investigated by dissolution in HF/H2SO4. When combined with chemical elements analyses and characterizations, the results of the dissolution behaviors revealed that α-spodumene and albite were preferentially dissolved over quartz. Insoluble fluoroaluminates, such as AlF3, cryolite (Na3AlF6 and cryolithionite (Na3Li3Al2F12, were generated and might be further partially dissolved by H2SO4. Fluorosilicates, such as K2SiF6, Na2SiF6, or KNaSiF6, were also generated as a part of the insoluble residues. This work provides fundamental insight into the role of HF/H2SO4 played in the dissolution of α-spodumene, and sheds light on a novel and promising process to efficiently extract lithium.

  7. Applications of lithium in nuclear energy

    Energy Technology Data Exchange (ETDEWEB)

    Oliviera, Glaucia A.C. de; Bustillos, José O.V.; Ferreira, João C.; Bergamaschi, Vanderlei S.; Moraes, Rafaeli M. de; Gimenez, Maíse P.; Miyamoto, Flavia K.; Seneda, José A., E-mail: glaucia.oliveira@ipen.br, E-mail: ovega@ipen.br, E-mail: jcferrei@ipen.br, E-mail: vsberga@ipen.br, E-mail: rafaeli.medeiros.moraes@gmail.com, E-mail: maisepastore@hotmail.com, E-mail: fla.kimiyamoto@gmail.com, E-mail: jaseneda@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN-CNEN/SP), Paulo, SP (Brazil)

    2017-07-01

    Lithium is a material of great interest in the world, it is found in different minerals on Earth's crust (spodumene, lepidolite, amblygonite and petalite) also in salt pans. This element belongs to alkaline group and has two natural isotopes: Li-6 and Li-7. In the nuclear field, lithium isotopes are used for different purposes. The Li-6 is applied in the production of energy, because its section of shock is larger than the other isotope. The Li-7 regulates the pH in refrigerant material in the primary circuits of the Pressurized Water Nuclear Reactor (PWR). In nuclear reactor, lithium is used as a heat transfer due its boiling temperature (1342°C), making it an excellent thermal conductor. However, to reach all these applications, lithium must have high purity (> 99%). The main processes to reach a high purity level of lithium employee a combination of solvent extraction and ion exchange process, to obtain its salts or ending with chemical electrolysis of its chlorides to obtain its pure metal. This work presents a review of new applications of Lithium in Nuclear Energy and its purification and enrichment processes. (author)

  8. Applications of lithium in nuclear energy

    International Nuclear Information System (INIS)

    Oliviera, Glaucia A.C. de; Bustillos, José O.V.; Ferreira, João C.; Bergamaschi, Vanderlei S.; Moraes, Rafaeli M. de; Gimenez, Maíse P.; Miyamoto, Flavia K.; Seneda, José A.

    2017-01-01

    Lithium is a material of great interest in the world, it is found in different minerals on Earth's crust (spodumene, lepidolite, amblygonite and petalite) also in salt pans. This element belongs to alkaline group and has two natural isotopes: Li-6 and Li-7. In the nuclear field, lithium isotopes are used for different purposes. The Li-6 is applied in the production of energy, because its section of shock is larger than the other isotope. The Li-7 regulates the pH in refrigerant material in the primary circuits of the Pressurized Water Nuclear Reactor (PWR). In nuclear reactor, lithium is used as a heat transfer due its boiling temperature (1342°C), making it an excellent thermal conductor. However, to reach all these applications, lithium must have high purity (> 99%). The main processes to reach a high purity level of lithium employee a combination of solvent extraction and ion exchange process, to obtain its salts or ending with chemical electrolysis of its chlorides to obtain its pure metal. This work presents a review of new applications of Lithium in Nuclear Energy and its purification and enrichment processes. (author)

  9. [Synthetic Studies of Bioactive Heterocyclic Natural Products and Fused Heterocyclic Compounds Based on the Thermal Electrocyclic or Azaelectocyclic Reaction of 6π-Electron or Aza-6π-electron Systems].

    Science.gov (United States)

    Hibino, Satoshi

    2016-01-01

    Since 1979, synthetic studies of bioactive heterocyclic natural products and condensed heteroaromatic compounds based on the thermal electrocyclic reaction of 6π-electron or aza-6π-electron systems incorporating the double bond of the principal aromatic or heteroaromatic ring have been conducted by our research group. In this review, five types of electrocyclic and azaelectrocyclic reaction are described: 1) the synthesis of the carbazole alkaloids hyellazole and 6-chlorohyellazole through the electrocyclic reaction of 2,3-bisalkenylindoles; 2) synthetic studies of the pyridocarbazole alkaloids ellipticine and olivacine through the electrocyclic reactions of the indole-2,3- and pyridine-3,4-quinodimethane intermediates; 3) synthetic studies of polysubstituted carbazole alkaloids through the allene-mediated electrocyclic reactions involving the indole 2,3-bond; 4) synthetic studies of fused pyridine rings through the azaelectrocyclic reaction of the 1-aza-6π-electron system using the oxime or oxime ether; and 5) synthetic studies of fused pyridine rings through the azaelectrocyclic reaction of the 2-aza-6π-electron system using a carbodiimide or isocyanate.

  10. Dissolved nitrogen in liquid lithium - a problem in fusion reactor chemistry

    International Nuclear Information System (INIS)

    Hubberstey, P.

    1984-01-01

    When dissolved in liquid lithium, nitrogen adopts the role filled by oxygen in liquid sodium systems, reacting readily with stainless steel containment materials to form Li 9 CrN 5 as a surface product; extended reaction leads to pronounced corrosion and embrittlement problems. It also interacts with both carbon and silicon impurities forming Li 2 NCN and Li 5 SiN 3 , respectively; it is inert, however, to oxygen impurity. Although dissolved nitrogen reacts with neither the tritium generated in the breeding process nor the lead added to act as a neutron multiplier, its presence may seriously influence tritium recovery processes since it reacts with and hence may poison the majority of the transition metals (Y,Ti,Zr) presently being considered as tritium getter materials. Its reactivity with these metals forms the basis of the hot trapping technique used to remove dissolved nitrogen from liquid lithium systems; cold trapping is ineffective because of its large solubility even at temperatures just above the melting point of pure lithium (453.6K). Whenever possible, the chemistry of nitrogen dissolved in liquid lithium is rationalised using the thermodynamic concepts and its significance to fusion reactor technology stressed. (author)

  11. Highly Oriented Graphene Sponge Electrode for Ultra High Energy Density Lithium Ion Hybrid Capacitors.

    Science.gov (United States)

    Ahn, Wook; Lee, Dong Un; Li, Ge; Feng, Kun; Wang, Xiaolei; Yu, Aiping; Lui, Gregory; Chen, Zhongwei

    2016-09-28

    Highly oriented rGO sponge (HOG) can be easily synthesized as an effective anode for application in high-capacity lithium ion hybrid capacitors. X-ray diffraction and morphological analyses show that successfully exfoliated rGO sponge on average consists of 4.2 graphene sheets, maintaining its three-dimensional structure with highly oriented morphology even after the thermal reduction procedure. Lithium-ion hybrid capacitors (LIC) are fabricated in this study based on a unique cell configuration which completely eliminates the predoping process of lithium ions. The full-cell LIC consisting of AC/HOG-Li configuration has resulted in remarkably high energy densities of 231.7 and 131.9 Wh kg(-1) obtained at 57 W kg(-1) and 2.8 kW kg(-1). This excellent performance is attributed to the lithium ion diffusivity related to the intercalation reaction of AC/HOG-Li which is 3.6 times higher that of AC/CG-Li. This unique cell design and configuration of LIC presented in this study using HOG as an effective anode is an unprecedented example of performance enhancement and improved energy density of LIC through successful increase in cell operation voltage window.

  12. Lithium in the treatment of aggression.

    Science.gov (United States)

    Sheard, M H

    1975-02-01

    Lithium has become a widely accepted treatment for manic-depressive psychosis. It is dramatically effective for many cases of mania and is useful in the prevention of manic and depressive episodes. Hyperaggressiveness and hypersexuality are frequent components of manic-depressive illness and abate under the influence of lithium. A brief review is presented of the behavioral and biochemical pharmacology of lithium. This documents the inhibitory role which lithium can play in several examples of animal aggressive behavior including pain-elicited aggression, mouse killing in rats, isolation-induced aggression in mice, p-chlorophenylalanine-induced aggression in rats, and hypothalamically induced aggression in cats. The use of lithium to control human aggressive behavior has resulted in controversial findings. In epileptic conditions, improvement has been reported in interseizure aggressivity, but other reports indicate the possibility of increased seizures. Improvement in aggressive behavior in childhood has occasionally been reported as well as in emotionally unstable character disorders in young female patients. Te was a single blind study and the other a large but uncontrolled study. Both studies reported an improvement in aggressiveness as indicated by fewer recorded reports (tickets) for fighting. The final study reported is a study of 12 male delinquents age 16 to 23. They received lithium or placebo for 4 months inside an institution and then a trial of lithium for 1 to 12 months on an outpatient basis. Analysis of results in terms of the number of aggressive antisocial acts showed fewer serious aggressive episodes when the lithium level was between 0.6 and 1 meq/liter than when it was between 0.0 and 0.6 meq/liter. These results must be viewed with caution and are only suggestive since the study was not double blind.

  13. Role of rotational energy and deformations in the dynamics of {sup 6}Li+{sup 90}Zr reaction

    Energy Technology Data Exchange (ETDEWEB)

    Kaur, Gurvinder; Grover, Neha; Sandhu, Kirandeep; Sharma, Manoj K., E-mail: msharma@thapar.edu

    2014-07-15

    In reference to recent experimental data, the dynamical cluster-decay model (DCM) has been applied to study the neutron evaporation residue (ER) cross sections of intermediate mass nucleus {sup 96}Tc{sup ⁎} spread over a wide range of incident energy across the Coulomb barrier. In order to analyze the effect of rotational energy in the dynamics of {sup 6}Li+{sup 90}Zr reaction, the cross sections have been calculated using the sticking (I{sub S}) and the non-sticking (I{sub NS}) limits of moment of inertia with inclusion of quadrupole (β{sub 2}) deformation within optimum orientation approach. The effect of either of the two approaches on the angular momentum, and hence the rotational energy associated with it, is assessed through the fragment mass distribution, preformation factor and the barrier penetrability. Also, the role of deformations is studied through a comparative analysis of decay path for spherical and β{sub 2} deformed fragmentation. The calculated evaporation residue cross sections show excellent agreement with the reported data at all incident energies for both spherical and β{sub 2}-deformed approach. Finally, the incomplete fusion (ICF) process observed due to loosely bound projectile {sup 6}Li is addressed within the framework of DCM.

  14. Vinyl ethers, containing isothiocyanate group. 12. Reaction of 2-vinyloxyethylisothiocyanate with metallated ethoxyethene, methoxyalline and 2-alkynes: 2,3-disubstituted N-(2-vinyloxyethyl) pyrroles and 6-(vinyloxymethyl)-5,6-dihydropyridines

    International Nuclear Information System (INIS)

    Nedolya, N.A.; Brandsma, L.; Zinov'eva, V.P.; Trofimov, B.A.

    1997-01-01

    New route of synthesis of 1,2,3-trisubstituted pyrroles and 2,3,6-trisubstituted 5,6-dyhydropyridines by the reaction of lithiated alkoxyallenes and 2-alkynes with 2-vinyloxyethylisothiocyanate is found. It is shown that key intermediates are 1,3,4-azatrienes. Reaction of metallized ethoxyethene with 2-vinyloxyethyisothiocyanate (after intermediate alkylation) results in 1-(2-vinyloxyethyl)-1,3-azadiene

  15. Experimental lithium system experience

    International Nuclear Information System (INIS)

    Atwood, J.M.; Berg, J.D.; Kolowith, R.; Miller, W.C.

    1984-01-01

    The Experimental Lithium System is a test loop built to support design and operation of the Fusion Materials Irradiation Test Facility. ELS has achieved over 15,000 hours of safe and reliable operation. An extensive test program has demonstrated satisfactory performance of the system components, including an electromagnetic pump, lithium jet target, and vacuum system. Data on materials corrosion and behavior of lithium impurities are also presented. (author)

  16. Redox Reactions of Reduced Flavin Mononucleotide (FMN), Riboflavin (RBF), and Anthraquinone-2,6-disulfonate (AQDS) with Ferrihydrite and Lepidocrocite

    Energy Technology Data Exchange (ETDEWEB)

    Shi, Zhi [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zachara, John M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shi, Liang [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Zheming [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Moore, Dean A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kennedy, David W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Fredrickson, Jim K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2012-09-17

    Flavins are secreted by the dissimilatory iron-reducing bacterium Shewanella and can function as endogenous electron transfer mediators (ETM). In order to assess the potential importance of flavins in Fe(III) bioreduction, we investigated the redox reaction kinetics of reduced flavins (FMNH2 and RBFH2) with ferrihydrite and lepidocrocite. The organic reductants rapidly reduced and dissolved ferrihydrite and lepidocrocite in the pH range 4-8. The rate constant k for 2-line ferrihydrite reductive dissolution by FMNH2 was 87.5 ± 3.5 M-1∙s-1 at pH 7.0 in batch reactors, and the k was similar for RBFH2. For lepidocrocite, the k was 500 ± 61 M-1∙s-1 for FMNH2, and 236 ± 22 M-1∙s-1 for RBFH2. The surface area normalized initial reaction rates (ra) were between 0.08 and 77 μmoles∙m-2∙s-1 for various conditions in stopped-flow experiments. Initial rates (ro) were first-order with respect to Fe(III) oxide concentration, and ra increased with decreasing pH. Poorly crystalline 2-line ferrihydrite yielded the highest ra, followed by more crystalline 6-line ferrihydrite, and crystalline lepidocrocite. Compared to a previous whole-cell study with Shewanella oneidensis strain MR-1, our findings suggest that ETM reduction by the Mtr pathway coupled to lactate oxidation are rate limiting, rather than heterogeneous electron transfer to the Fe(III) oxide.

  17. Antagonist targeting microRNA-155 protects against lithium-pilocarpine-induced status epilepticus in C57BL/6 mice by activating brain-derived neurotrophic factor

    Directory of Open Access Journals (Sweden)

    Zhengxu eCai

    2016-05-01

    Full Text Available Epilepsy is a severe brain disorder affecting numerous patients. Recently, it is inferred that modulation of microRNA-155 (miR-155 could serve as a promising treatment of mesial temporal lobe epilepsy (MTLE. In the current study, the therapeutic potential of miR-155 antagonist against TLE was evaluated and the underlying mechanism involved in this regulation was explored. TLE model was induced by lithium-pilocarpine method. The effect of miR-155 antagonist on epilepticus symptoms of TLE mice was assessed using Racine classification and electroencephalogram (EEG recordings. The expression of brain-derived neurotrophic factor (BDNF and its association with miR-155 were also assessed with a series of experiments. Our results showed that level of miR-155 was significantly up-regulated after induction of TLE model. Based on the results of EEG and behavior analyses, seizures in mice were alleviated by miR-155 antagonist. Moreover, administration of miR-155 antagonist also significantly increased the level of BDNF. The results of dual luciferase assay and western blotting showed that miR-155 antagonist exerted its action on status epilepticus by directly regulating the activity of BDNF. Taken all the information together, our results demonstrated that miR-155 antagonist might firstly induce the expression of BDNF, which then contributed to the alleviation of epilepsy in the current study.

  18. Equilibrium and kinetic studies of systems of hydrogen isotopes, lithium hydrides, aluminum, and LiAlO2

    International Nuclear Information System (INIS)

    Owen, J.H.; Randall, D.

    1976-01-01

    Tritium might be bred by the 6 Li(n,α)T reaction in a solid lithium alloy or compound in the blanket of a controlled thermonuclear reactor to avoid problems associated with molten lithium or lithium compounds. Li--Al and LiAlO 2 systems containing hydrogen, deuterium, or tritium were studied 10 to 15 years ago at the Savannah River Laboratory. This paper descibes measurements of (1) the distribution of tritium and helium throughout both α and β phases of irradiated Li--Al alloy, (2) the migration rate of tritium to the β phase during moderate heating, (3) equilibrium pressures as functions of temperature of H 2 , D 2 , or T 2 in contact with lithium hydrides + aluminum, Li--Al alloy, or irradiated Li--Al alloy, (4) the equilibrium constant for the reaction LiH + Al → LiAl + 1 / 2 H 2 as a function of temperature, and (5) extraction rates of tritium from irradiated LiAlO 2 targets at elevated temperatures

  19. Pd-catalyzed versus uncatalyzed, PhI(OAc)2-mediated cyclization reactions of N6-([1,1'-biaryl]-2-yl)adenine nucleosides.

    Science.gov (United States)

    Satishkumar, Sakilam; Poudapally, Suresh; Vuram, Prasanna K; Gurram, Venkateshwarlu; Pottabathini, Narender; Sebastian, Dellamol; Yang, Lijia; Pradhan, Padmanava; Lakshman, Mahesh K

    2017-11-09

    In this work we have assessed reactions of N 6 -([1,1'-biaryl]-2-yl)adenine nucleosides with Pd(OAc) 2 and PhI(OAc) 2 , via a Pd II /Pd IV redox cycle. The substrates are readily obtained by Pd/Xantphos-catalyzed reaction of adenine nucleosides with 2-bromo-1,1'-biaryls. In PhMe, the N 6 -biarylyl nucleosides gave C6-carbazolyl nucleoside analogues by C-N bond formation with the exocyclic N 6 nitrogen atom. In the solvent screening for the Pd-catalyzed reactions, an uncatalyzed process was found to be operational. It was observed that the carbazolyl products could also be obtained in the absence of a metal catalyst by reaction with PhI(OAc) 2 in 1,1,1,3,3,3-hexafluoroisopropanol (HFIP). Thus, under Pd catalysis and in HFIP, reactions proceed to provide carbazolyl nucleoside analogues, with some differences. If reactions of N 6 -biarylyl nucleoside substrates were conducted in MeCN, formation of aryl benzimidazopurinyl nucleoside derivatives was observed in many cases by C-N bond formation with the N 1 ring nitrogen atom of the purine (carbazole and benzimidazole isomers are readily separated by chromatography). Whereas Pd II /Pd IV redox is responsible for carbazole formation under the metal-catalyzed conditions, in HFIP and MeCN radical cations and/or nitrenium ions can be intermediates. An extensive set of radical inhibition experiments was conducted and the data are presented.

  20. Electrochemical Properties of the LiNi0.6Co0.2Mn0.2O2 Cathode Material Modified by Lithium Tungstate under High Voltage.

    Science.gov (United States)

    Fu, Jiale; Mu, Daobin; Wu, Borong; Bi, Jiaying; Cui, Hui; Yang, Hao; Wu, Hanfeng; Wu, Feng

    2018-05-31

    An amount (5 wt %) of lithium tungstate (Li 2 WO 4 ) as an additive significantly improves the cycle and rate performances of the LiNi 0.6 Co 0.2 Mn 0.2 O 2 electrode at the cutoff voltage of 4.6 V. The 5 wt % Li 2 WO 4 -mixed LiNi 0.6 Co 0.2 Mn 0.2 O 2 electrode delivers a reversible capacity of 199.2 mA h g -1 and keeps 73.1% capacity for 200 cycles at 1 C. It retains 67.4% capacity after 200 cycles at 2 C and delivers a discharge capacity of 167.3 mA h g -1 at 10 C, while those of the pristine electrode are only 44.7% and 87.5 mA h g -1 , respectively. It is shown that the structure of the LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathode material is not affected by mixing Li 2 WO 4 . The introduced Li 2 WO 4 effectively restrains the LiPF 6 and carbonate solvent decomposition by consuming PF 5 at high cutoff voltage, forming a stable cathode/electrolyte interface film with low resistance.

  1. Tailored lithium storage performance of graphene aerogel anodes with controlled surface defects for lithium-ion batteries

    International Nuclear Information System (INIS)

    Shan, Hui; Xiong, Dongbin; Li, Xifei; Sun, Yipeng; Yan, Bo; Li, Dejun; Lawes, Stephen; Cui, Yanhua; Sun, Xueliang

    2016-01-01

    Graphical abstract: - Highlights: • The graphene aerogel (GA) with controllable surface defects was synthesized. • The graphene aerogel anodes showed high specific capacity and excellent cyclability. • Surface defects on the GA significantly function for lithium storage. • This study can extend the application of the graphene anodes for LIBs. - Abstract: Three dimensional self-assembled graphene aerogel (GA) anode materials with some surface defects have been successfully generated through a facile hydrothermal procedure using graphene oxide as precursor. The morphologies and textural properties of as-obtained GA were investigated by scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, Raman and other spectroscopy techniques. The surface defects and electrical conductivities of GA can be controlled by adjusting the hydrothermal reaction time. The results indicate that GA with a reaction time of 6 h exhibits extremely high reversible capacity (1430 mAh g"−"1 at the current density of 100 mA g"−"1) and superior rate capability (587 mAh g"−"1 at 800 mA g"−"1) with excellent cycling stability (maintaining a reversible capacity of 960 mAh g"−"1 at 100 mA g"−"1 after 100 cycles). It is demonstrated that the 3D porous network with increased defect density, as well as the considerable electrical conductivity, results in the excellent electrochemical performance of the as-made GA anodes in lithium-ion batteries.

  2. Lithium Enolates in the Enantioselective Construction of Tetrasubstituted Carbon Centers with Chiral Lithium Amides as Noncovalent Stereodirecting Auxiliaries.

    Science.gov (United States)

    Yu, Kai; Lu, Ping; Jackson, Jeffrey J; Nguyen, Thuy-Ai D; Alvarado, Joseph; Stivala, Craig E; Ma, Yun; Mack, Kyle A; Hayton, Trevor W; Collum, David B; Zakarian, Armen

    2017-01-11

    Lithium enolates derived from carboxylic acids are ubiquitous intermediates in organic synthesis. Asymmetric transformations with these intermediates, a central goal of organic synthesis, are typically carried out with covalently attached chiral auxiliaries. An alternative approach is to utilize chiral reagents that form discrete, well-defined aggregates with lithium enolates, providing a chiral environment conducive of asymmetric bond formation. These reagents effectively act as noncovalent, or traceless, chiral auxiliaries. Lithium amides are an obvious choice for such reagents as they are known to form mixed aggregates with lithium enolates. We demonstrate here that mixed aggregates can effect highly enantioselective transformations of lithium enolates in several classes of reactions, most notably in transformations forming tetrasubstituted and quaternary carbon centers. Easy recovery of the chiral reagent by aqueous extraction is another practical advantage of this one-step protocol. Crystallographic, spectroscopic, and computational studies of the central reactive aggregate, which provide insight into the origins of selectivity, are also reported.

  3. Enhancing effects of chronic lithium on memory in the rat.

    Science.gov (United States)

    Tsaltas, Eleftheria; Kontis, Dimitrios; Boulougouris, Vasileios; Papakosta, Vasiliki-Maria; Giannou, Haralambos; Poulopoulou, Cornelia; Soldatos, Constantine

    2007-02-12

    In spite of recent enrichment of neurochemical and behavioural data establishing a neuroprotective role for lithium, its primary effects on cognitive functioning remain ambiguous. This study examines chronic lithium effects on spatial working memory and long-term retention. In three discrete experiments, rats subjected to 30 daily intraperitoneal injections (2mmol/kg) of lithium (lithium groups: serum lithium=0.5+/-0.4mEq/l, 12h post-injection) or saline (controls) were trained in 0-s delay T-maze alternation and then tested in 30-, 45- and 60-s delay alternation (Experiments 1, 2, 3, respectively). Animals from Experiment 1 were further tested in one-trial step-through passive avoidance under mild shock parameters (0.5mA, 1s). Retention was assessed 6h later. Daily lithium or saline injections continued throughout behavioural testing. Lithium animals were indistinguishable from controls during 0-delay alternation baseline (Experiments 1-3, accuracy>88%) but showed significantly higher accuracy than controls at 30- and 45-s delays (93% versus 85% and 92% versus 82%, Experiments 1 and 2, respectively). At 60-s delay (Experiment 3) this beneficial effect of lithium was no longer apparent (lithium and control accuracy=78%). In Experiment 4, the shock used did not support 6-h passive avoidance retention in controls, whereas lithium animals showed significant step-through latency increases. Chronic lithium enhanced spatial working memory and promoted long-term retention of a weak aversive contingency. The results suggest that lithium may have potential as a cognitive enhancer.

  4. Neutron dosimetry using aqueous solutions of lithium acetate

    International Nuclear Information System (INIS)

    Rakovan, L.J.

    1996-01-01

    A thermal neutron dosimetry system using the 6 Li(n,α) 3 H reaction and liquid scintillation counting of tritium was developed. Lithium acetate was chosen to supply the 6 Li in the aqueous dosimetry solutions. Neutron irradiations were completed using The Ohio State University Research Reactor. After two sets of samples were irradiated, variables in the system such as the mass of lithium acetate in the solutions and the counting window of the liquid scintillation counter used to analyze the sample were chosen. The system was evaluated by completing two sets of 23 minute irradiations with the reactor at 500 kW, 50 kW, 5 kW, and one irradiation at 500 W. The samples irradiated at 500 W were below the threshold of the system, and could not be used. Prompt analysis was essential due to loss of detectable emissions in the dosimetry solutions over time. The thermal neutron fluences calculated with the data from the samples were compared to the fluences determined from gold wire irradiations. The fluence values differed at most by 6%. The fluence values calculated from the samples were consistently less than those determined from the gold wires

  5. Adsorption of lithium ion to amorphous hydrous aluminium oxide

    International Nuclear Information System (INIS)

    Wada, Hideo; Kitamura, Takao; Fujii, Ayako; Katoh, Shunsaku

    1982-01-01

    Adsorption process of lithium ion to amorphous hydrous aluminium oxide (a-HAO) was investigated by pH titration method with lithium chloride-lithium hydroxide mixed solution and X-ray diffraction analysis of a-HAO after pH titration. In the pH titration, the addition of hydroxide ion in amount from 0 to 4.0 mmol.g -1 gave no change to the pH of the solution and caused adsorption of lithium ion equivalent in amount to added hydroxide ion. X-ray diffraction analysis showed the formation of lithium hydrogenaluminate LiH (AlO 2 ) 2 .5H 2 O (LHA) in the a-HAO after pH titration. These results showed that adsorption of lithium ion by a-HAO was related to a reaction which consumed hydroxide ion and formed LHA. In order to elucidate detail process of the reaction, changes of pH, aluminium concentration and lithium concentration of the solution, respectively with time, were determined. The pH of the solution decreased in two stages. At the first stage of the pH decrease, the aluminium concentration increased whereas the lithium concentration did not change. At the second stage, the lithium concentration decreased together with the decrease of the aluminium concentration. It was inferred that adsorption of lithium ion proceeded through dissolution of a-HAO and precipitation of LHA. Theoretical adsorption capacity calculated from the above formula for LHA and aluminium content in a-HAO was 4.7 mmol.g -1 and agreed fairly well with observed value 4.0 mmol.g -1 . (author)

  6. Enhanced Bacterial α(2,6-Sialyltransferase Reaction through an Inhibition of Its Inherent Sialidase Activity by Dephosphorylation of Cytidine-5'-Monophosphate.

    Directory of Open Access Journals (Sweden)

    Ji-Yeon Kang

    Full Text Available Bacterial α(2,6-sialyltransferases (STs from Photobacterium damsela, Photobacterium sp. JT-ISH-224, and P. leiognathi JT-SHIZ-145 were recombinantly expressed in Escherichia coli and their ST activities were compared directly using a galactosylated bi-antennary N-glycan as an acceptor substrate. In all ST reactions, there was an increase of sialylated glycans at shorter reaction times and later a decrease in prolonged reactions, which is related with the inherent sialidase activities of bacterial STs. These sialidase activities are greatly increased by free cytidine monophosphate (CMP generated from a donor substrate CMP-N-acetylneuraminic acid (CMP-Neu5Ac during the ST reactions. The decrease of sialylated glycans in prolonged ST reaction was prevented through an inhibition of sialidase activity by simple treatment of alkaline phosphatase (AP, which dephosphorylates CMP to cytidine. Through supplemental additions of AP and CMP-Neu5Ac to the reaction using the recombinant α(2,6-ST from P. leiognathi JT-SHIZ-145 (P145-ST, the content of bi-sialylated N-glycan increased up to ~98% without any decrease in prolonged reactions. This optimized P145-ST reaction was applied successfully for α(2,6-sialylation of asialofetuin, and this resulted in a large increase in the populations of multi-sialylated N-glycans compared with the reaction without addition of AP and CMP-Neu5Ac. These results suggest that the optimized reaction using the recombinant P145-ST readily expressed from E. coli has a promise for economic glycan synthesis and glyco-conjugate remodeling.

  7. Lithium mass transport in ceramic breeder materials

    International Nuclear Information System (INIS)

    Blackburn, P.E.; Johnson, C.E.

    1990-01-01

    The objective of this activity is to measure the lithium vaporization from lithium oxide breeder material under differing temperature and moisture partial pressure conditions. Lithium ceramics are being investigated for use as tritium breeding materials. The lithium is readily converted to tritium after reacting with a neutron. With the addition of 1000 ppM H 2 to the He purge gas, the bred tritium is readily recovered from the blanket as HT and HTO above 400 degree C. Within the solid, tritium may also be found as LiOT which may transport lithium to cooler parts of the blanket. The pressure of LiOT(g), HTO(g), or T 2 O(g) above Li 2 O(s) is the same as that for reactions involving hydrogen. In our experiments we were limited to the use of hydrogen. The purpose of this work is to investigate the transport of LiOH(g) from the blanket material. 8 refs., 1 fig., 3 tabs

  8. Reaction of a chemotherapeutic agent, 6-mercaptopurine, with a direct-acting, electrophilic carcinogen, benzo[a]pyrene-7,8-diol 9,10-epoxide.

    Science.gov (United States)

    MacLeod, M C; Stewart, E; Daylong, A; Lew, L K; Evans, F E

    1991-01-01

    The chemotherapeutic agent 6-mercaptopurine (6-MP) has been shown to react covalently with the ultimate carcinogenic metabolite of benzo[a]pyrene, 7-r,8-t-dihydroxy-9-t,10-t-oxy-7,8,9,10-tetrahydrobenzo[a]pyrene (BPDE), in aqueous solution, forming a single adduct. NMR studies of the HPLC-purified product were consistent with its identification as 10(S)-(6'-mercaptopurinyl)-7,8,9-trihydroxy-7,8,9,10- tetrahydrobenzo[a]pyrene. Reaction kinetics were analyzed by using both HPLC separation of the products formed and a spectrophotometric assay for adduct formation. A simple model in which direct reaction between 6-MP and BPDE takes place without formation of a physical complex was found to adequately predict the dependence of product ratios on 6-MP concentration. Variations in the observed rate constant for this reaction with changes in temperature, pH, and buffer concentration were determined and compared to the effects of these variables on the observed rate constant for BPDE hydrolysis. In each case, the processes were affected quite differently, suggesting that different rate-determining steps are involved. The data suggest that the reaction mechanism involves SN2 attack of the anion of 6-MP, formed by ionization of the sulfhydryl group, on carbon 10 of BPDE, resulting in a trans-9,10 reaction product.

  9. Research and development of lithium isotope separation using an ionic-liquid impregnated organic membrane

    International Nuclear Information System (INIS)

    Hoshino, Tsuyoshi

    2013-01-01

    The tritium needed as a fuel for fusion reactors is produced by the neutron capture reaction of lithium-6 ( 6 Li) in tritium breeding materials. However, natural Li contains only about 7.6 at.% 6 Li. In Japan, new lithium isotope separation technique using ionic-liquid impregnated organic membranes have been developed. The improvement in the durability of the ionic-liquid impregnated organic membrane is one of the main issues for stable, long-term operation of electrodialysis cells while maintaining good performance. Therefore, we developed highly-durable ionic-liquid impregnated organic membrane. Both ends of the ionic-liquid impregnated organic membrane were covered by a nafion 324 overcoat to prevent the outflow of the ionic liquid. The transmission of Lithium aqueous solution after 10 hours under the highly-durable ionic-liquid impregnated organic membrane is almost 13%. So this highly-durable ionic-liquid impregnated organic membrane for long operating of electrodialysis cells has been developed through successful prevention of ion liquid dissolution. (J.P.N.)

  10. Development of lithium target for accelerator based neutron capture therapy

    International Nuclear Information System (INIS)

    Taskaev, Sergey; Bayanov, Boris; Belov, Victor; Zhoorov, Eugene

    2006-01-01

    Pilot innovative accelerator based neutron source for neutron capture therapy of cancer is now of the threshold of its operation at the BINP, Russia. One of the main elements of the facility is lithium target producing neutrons via threshold 7 Li(p,n) 7 Be reaction at 25 kW proton beam with energies 1.915 MeV or 2.5 MeV. The main problems of lithium target were determined to be: 7 Be radioactive isotope activation keeping lithium layer solid, presence of photons due to proton inelastic scattering on lithium nuclei, and radiation blistering. The results of thermal test of target prototype were presented as previous NCT Congress. It becomes clear that water is preferable for cooling the target, and that lithium target 10 cm in diameter is able to run before melting. In the present report, the conception of optimal target is proposed: thin metal disk 10 cm in diameter easy for detaching, with evaporated thin layer of pure lithium from the side of proton beam exposure, its back being intensively cooled with turbulent water flow to maintain lithium layer solid. Design of the target for the neutron source constructed at BINP is shown. The results of investigation of radiation blistering and lithium layer are presented. Target unit of facility is under construction now, and obtaining neutrons is expected in nearest future. (author)

  11. Study of fusion and nucleon transfer channels in the Au-197 + He-6 reaction in an energy range of He-6 to 20 Mev/A

    Czech Academy of Sciences Publication Activity Database

    Skobelev, N. K.; Penionzhkevich, Y. E.; Kulko, A. A.; Demekhina, N. A.; Kroha, Václav; Kugler, Andrej; Lukyanov, S.; Mrázek, Jaromír; Sobolev, Yu. G.; Maslov, V. A.; Muzychka, Yu. A.; Voskoboynik, E. I.; Fomichev, A. S.

    2013-01-01

    Roč. 10, č. 3 (2013), s. 248-255 ISSN 1547-4771 Institutional support: RVO:61389005 Keywords : nuclear reactions * gamma activity * cross section Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders

  12. Growth and characterization of pure and lithium doped strontium ...

    Indian Academy of Sciences (India)

    TECS

    Abstract. The effect of lithium ion as dopant on the size and transparency of strontium tartrate tetrahydrate. (SrC4H4O6⋅4H2O) crystals are presented in this paper. Growth of single crystals of undoped and lithium doped strontium tartrate tetrahydrate by controlled diffusion of strontium nitrate into the gel charged with.

  13. 16O resonances near the 4α threshold through the 12C(6Li,d) reaction

    Science.gov (United States)

    Rodrigues, M. R. D.; Borello-Lewin, T.; Miyake, H.; Duarte, J. L. M.; Rodrigues, C. L.; Souza, M. A.; Horodynski-Matsushigue, L. B.; Ukita, G. M.; Cappuzzello, F.; Cunsolo, A.; Cavallaro, M.; Agodi, C.; Foti, A.

    2014-02-01

    Background: Resonances around xα thresholds in light nuclei are recognized to be important in basic aspects of nuclear structure. However, there is scarce experimental information associated with them. Purpose: We study the α-clustering phenomenon in resonant states around the 4α threshold (14.44 MeV) in the 16O nucleus. Method: The 12C(6Li,d )16O reaction was investigated with an unprecedented resolution at a bombarding energy of 25.5 MeV by employing the São Paulo Pelletron-Enge-Spectrograph facility and the nuclear emulsion technique. Results: Several narrow resonances were populated and the energy resolution of 15 keV allows for the separation of doublet states that were not resolved previously. The upper limits for the resonance widths in this region were extracted. The angular distributions of the absolute differential cross section associated with four natural parity quasibound states are presented and compared to distorted wave Born approximation predictions. Conclusions: Narrow resonances not previously reported in the literature were observed. This indicates that the α-cluster structure information in this region should be revised.

  14. Study of fission reactions induced by 4,6He and 7Li beams on 209Bi and 208Pb targets

    Directory of Open Access Journals (Sweden)

    Lukyanov S.M.

    2013-12-01

    Full Text Available Study of fission reactions induced by 4,6He and 7Li beams on 209Bi and 208Pb targets, leading to the production of 210,212A compound nuclei, was performed. It was shown that the fission excitation functions for the three reactions 4,6He + 209Bi and 7Li + 208Pb had similar behavior within the experimental error for a broad range of energy. More likely, halo structure of 6He is not reflected on the fission reaction mechanism. Otherwise, a large value of the fusion cross section was observed so far, as it could be expected in the case of weakly bound character of 6He projectile.

  15. Search for superheavy elements in the reaction 238U+9.6 MeV/N 63Cu,65Cu

    International Nuclear Information System (INIS)

    Esterlund, R.A.; Molzahn, D.; Brandt, R.; Patzelt, P.; Vater, P.; Boos, A.H.

    1976-01-01

    According to calculations of NIX and others, the formation of superheavy elements might occur in heavy-ion reaction systems such as the one under investigation in the present work i.e., 238 U + 63 Cu and 65 Cu at 9.6 MeV/nucleon. Since previous experiments have indicated that upper limits to the production cross-section for superheavy elements are extremely low, two rather long irradiations of 27 hrs and 42 hrs, respectively, have been carried out at the University of Manchester LINAC. The first run has already been reported on in the literature. In the case of the second run, after chemical separation into HgS, CdS, and La(OH) 3 fractions, the samples were assayed simultaneously and continuously over a period of 6 months for alpha- and spontaneous-fission activity, using Si surface-barrier detector. Each sample was at the same time mounted on mica, for the purpose of scanning for fission tracks at a later date. No indications from the data have so far been found that superheavy elements were produced. Possible reasons for the failure to detect superheavy elements in this experiment are: The half-life of any product is either too short (a few hours) or too long (a few years); the chemical properties of the superheavy elements are very different from those predicted; the position of the superheavy island is not where it is commonly assumed to be and may, for example, be at Z>=114 and N>=184, as predicted by ROUBEN et al. (T.G.)

  16. Study of the continuous spectrum of 6Li and the reaction t(3He,d)α by the algebraic version of the RGM

    International Nuclear Information System (INIS)

    Filippov, G.F.; Lopez Trujillo, A.; Rybkin, I.Yu.

    1992-01-01

    Using the algebraic version of the resonating group method, the continuous spectrum of 6 Li states with zero isospin is studied. The decay channels t+ 3 He and α+α are taken into account. The astrophysical S-factor of the t( 3 He,d)α reaction is calculated. 20 refs.; 6 figs.; 2 tab. (author)

  17. Lithium extraction from orthorhombic lithium manganese oxide and the phase-transformation to spinel

    CSIR Research Space (South Africa)

    Gummow, RJ

    1993-12-01

    Full Text Available Orthorhombic LiMnO2 products, synthesised by the reaction of gamma-MnO2 and LiOH in argon at 600-620 degrees C using carbon as a reducing agent, have been evaluated as electrode materials in lithium cells. Products that contained a minor proportion...

  18. Synthesis and characterization of cathode, anode and electrolyte materials for rechargeable lithium batteries

    Science.gov (United States)

    Yang, Shoufeng

    Two new classes of cathode materials were studied: iron phosphate/sulfate materials and layered manganese oxides, both of which are low cost and had shown some potential. The first class of materials have poor conductivity and cyclability. I studied a number of methods for increasing the conductivity, and determined that grinding the material with carbon black was as effective as special in-situ coatings. The optimum carbon loading was determined to be between 6 and 15 wt%. Too much carbon reduces the volumetric energy density, whereas too little significantly increased cell polarization (reduced the rate of reaction). The kinetic and thermodynamic stability of LiFePO 4 was also studied and it was determined that over discharge protection will be needed as irreversible Li3PO4 can be formed at low potentials. A novel hydrothermal synthesis method was developed, but the significant level of Fe on the Li site reduces the reaction rate too much. In the case of the layered manganese oxide, cation substitution with Co and Ni is found to be effective in avoiding Jahn-Teller effects and improving electrochemistry. A wide range of tin compounds have been suggested as lithium storage media for advanced anode materials, as tin can store over 4 Li per Sn atom. Lithium hexafluorophosphate, LiPF6, is presently the salt of choice for LiCoO2 batteries, but it is expensive and dissolves some manganese compounds. The lithium bis(oxolato)borate (BOB) salt was recently reported, and I made a study of its use in cells with the LiFePO4 cathode and the tin anode. During its synthesis, it became clear that LiBOB is very reactive with many solvents, and these complexes were characterized to better understand this new material. In LiBOB the lithium is five coordinated, an unstable configuration for the lithium ion so that water and many other solvents rapidly react to make a six coordination. Only in the case of ethylene carbonate was the lithium found to be four coordinated. The Li

  19. Elastic and inelastic scattering of 2 to 10 MeV protons by lithium isotopes

    International Nuclear Information System (INIS)

    Laurat, M.

    1969-01-01

    A description is given of the experimental set-up which has been devised for carrying out spectrometric and absolute cross-section measurements on the reactions induced by protons accelerated in a 12 MeV Van de Graaff Tandem. The particles are detected by silicon junctions; the weight of the targets (about ten μg/cm 2 ) is determined by the quartz method. The experimental equipment has been controlled by a study of proton scattering by lithium-6, and has made it possible to evaluate the elastic and inelastic scattering (1. level excitation) by lithium 7 of 2 to 9 MeV protons. The most probable spin and parity values for the six levels of 8 Be between 19 and 25 MeV excitation energy have been determined from a knowledge of the observed structure. (author) [fr

  20. Trojan horse particle invariance studied with the 6Li(d,α)4He and 7Li(p,α)4He reactions

    International Nuclear Information System (INIS)

    Pizzone, R. G.; Spitaleri, C.; Lamia, L.; Cherubini, S.; La Cognata, M.; Puglia, S. M. R.; Rapisarda, G. G.; Romano, S.; Sergi, M. L.; Bertulani, C.; Mukhamedzhanov, A.; Blokhintsev, L.; Burjan, V.; Hons, Z.; Kroha, V.; Mrazek, J.; Piskor, S.; Kiss, G. G.; Li, C.; Tumino, A.

    2011-01-01

    The Trojan horse nucleus invariance for the binary reaction cross section extracted from the Trojan horse reaction was tested using the quasifree 3 He( 6 Li,αα)H and 3 He( 7 Li,αα) 2 H reactions. The cross sections for the 6 Li(d,α) 4 He and 7 Li(p,α) 4 He binary processes were extracted in the framework of the plane wave approximation. They are compared with direct behaviors as well as with cross sections extracted from previous indirect investigations of the same binary reactions using deuteron as the Trojan horse nucleus instead of 3 He. The very good agreement confirms the applicability of the plane wave approximation which suggests the independence of the binary indirect cross section on the chosen Trojan horse nucleus, at least for the investigated cases.

  1. Recovery of lithium from the effluent obtained in the process of spent lithium-ion batteries recycling.

    Science.gov (United States)

    Guo, Xueyi; Cao, Xiao; Huang, Guoyong; Tian, Qinghua; Sun, Hongyu

    2017-08-01

    A novel process of lithium recovery as lithium ion sieve from the effluent obtained in the process of spent lithium-ion batteries recycling is developed. Through a two-stage precipitation process using Na 2 CO 3 and Na 3 PO 4 as precipitants, lithium is recovered as raw Li 2 CO 3 and pure Li 3 PO 4 , respectively. Under the best reaction condition (both the amounts of Na 2 CO 3 and Li 3 PO 4 vs. the theoretical ones are about 1.1), the corresponding recovery rates of lithium (calculated based on the concentration of the previous stage) are 74.72% and 92.21%, respectively. The raw Li 2 CO 3 containing the impurity of Na 2 CO 3 is used to prepare LiMn 2 O 4 as lithium ion sieve, and the tolerant level of sodium on its property is studied through batch tests of adsorption capacity and corrosion resistance. When the weight percentage of Na 2 CO 3 in raw Li 2 CO 3 is controlled less than 10%, the Mn corrosion percentage of LiMn 2 O 4 decreases to 21.07%, and the adsorption capacity can still keep at 40.08 mg g -1 . The results reveal that the conventional separation sodium from lithium may be avoided through the application of the raw Li 2 CO 3 in the field of lithium ion sieve. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Lithium Battery Diaper Ulceration.

    Science.gov (United States)

    Maridet, Claire; Taïeb, Alain

    2016-01-01

    We report a case of lithium battery diaper ulceration in a 16-month-old girl. Gastrointestinal and ear, nose, and throat lesions after lithium battery ingestion have been reported, but skin involvement has not been reported to our knowledge. © 2015 Wiley Periodicals, Inc.

  3. Cathode material for lithium batteries

    Science.gov (United States)

    Park, Sang-Ho; Amine, Khalil

    2013-07-23

    A method of manufacture an article of a cathode (positive electrode) material for lithium batteries. The cathode material is a lithium molybdenum composite transition metal oxide material and is prepared by mixing in a solid state an intermediate molybdenum composite transition metal oxide and a lithium source. The mixture is thermally treated to obtain the lithium molybdenum composite transition metal oxide cathode material.

  4. Startup of Experimental Lithium System

    International Nuclear Information System (INIS)

    McCauley, D.L.

    1980-06-01

    The Experimental Lithium System (ELS) is designed for full-scale testing of targets and other lithium system components for the Fusion Materials Irradiation Test (FMIT) Facility. The system also serves as a test bed for development of lithium purification and characterization equipment, provides experience in operation of large lithium systems, and helps guide FMIT design

  5. Lithium modified zeolite synthesis for conversion of biodiesel-derived glycerol to polyglycerol

    Energy Technology Data Exchange (ETDEWEB)

    Ayoub, Muhammad, E-mail: muhammad.ayoub@petronas.com.my [Department of Chemical Engineering, Universiti Teknologi PETRONAS, 31750, Tronoh, Perak, Malaysia and School of Chemical Engineering, Universiti Sains Malaysia, 43000, Pinang (Malaysia); Abdullah, Ahmad Zuhairi, E-mail: chzuhairi@usm.my [School of Chemical Engineering, Universiti Sains Malaysia, 43000, Pinang (Malaysia); Inayat, Abrar, E-mail: abrar.inayat@petronas.com.my [Department of Chemical Engineering, Universiti Teknologi PETRONAS, 31750, Tronoh, Perak (Malaysia)

    2014-10-24

    Basic zeolite has received significant attention in the catalysis community. These zeolites modified with alkaline are the potential replacement for existing zeolite catalysts due to its unique features with added advantages. The present paper covers the preparation of lithium modified zeolite Y (Li-ZeY) and its activity for solvent free conversion of biodiesel-derived glycerol to polyglycerol via etherification process. The modified zeolite was well characterized by X-ray diffraction (XRD), Scanning Electron Microscope (SEM) and Nitrogen Adsorption. The SEM images showed that there was no change in morphology of modified zeolite structure after lithium modification. XRD patterns showed that the structure of zeolite was sustained after lithium modification. The surface properties of parent and modified zeolite was also observed N{sub 2} adsortion-desorption technique and found some changes in surface area and pore size. In addition, the basic strength of prepared materials was measured by Hammet indicators and found that basic strength of Li-ZeY was highly improved. This modified zeolite was found highly thermal stable and active heterogamous basic catalyst for conversion of solvent free glycerol to polyglycerol. This reaction was conducted at different temperatures and 260 °C was found most active temperature for this process for reaction time from 6 to 12 h over this basic catalyst in the absence of solvent.

  6. A High-Pressure Study of Manganese Metal and its Reactions with CO2 at 6, 23, and 44 GPa

    Science.gov (United States)

    Sawchuk, K. L. S.; McGuire, C. P.; Greenburg, A.; Makhluf, A.; Kavner, A.

    2017-12-01

    The free energies of formation of oxides and carbonates at the extreme pressures and temperatures of Earth's interior provides some of the thermodynamic constrains for models of mantle/core formation and subsequent chemical evolution. The broad goal of our research program is to measure the pressure- and temperature-dependence of free energies of formation of transition metal oxides and carbonates. This requires measurements of the phase stability, density, and thermoelastic properties of metals, oxides, and carbonates at deep-Earth and planetary conditions. Manganese is of interest because it is one of the most abundant transition metal geochemical tracers, it readily forms a carbonate at ambient pressure, and its high-pressure carbonate and oxide densities and equation of state parameters are relatively unknown. Here we report new data on the pressure/volume equation of state and structure of manganese metal as well as its reactions with CO2. These measurements were made using a laser heated diamond anvil cell in conjunction with synchrotron-based X-ray diffraction at beamline 12.2.2 at the Advanced Light Source. Three samples of manganese metal were gas-loaded in a CO2 pressure medium and pressurized to 6, 23, and 44 GPa. Upon laser heating, the CO2 reacted with the Mn metal generating new phases. To analyze the diffraction patterns, we we use a python-based program developed in-house for extracting high resolution 2-dimensional diffraction peak position and intensity information from two-dimensional X-ray diffraction patterns. At each pressure step, the structure and density of the quenched Mn metal phase was determined. At 6 GPa, Mn metal adopts a BCC structure, and at 23 GPa a tetragonal distortion is observed in the lattice. The measured equation of state is in good agreement with an existing meaurement by Fujihisa and Takemura (1995). MnCO3 rhodochrosite is observed in the sample quenched after heating at 6 GPa. Additional high pressure phases are evident

  7. Lithium purity and characterization

    International Nuclear Information System (INIS)

    Meadows, G.E.; Keough, R.F.

    1981-02-01

    The accurate measurement of impurities in lithium is basic to the study of lithium compatibility with fusion reactor materials. In the last year the Hanford Engineering Development Laboratory (HEDL) has had the opportunity to develop sampling and analytical techniques and to apply them in support of the Experimental Lithium System (ELS) as a part of the Fusion Materials Irradiation Test Project. In this paper we present the analytical results from the fill, start-up and operation of the ELS. In addition, the analysis and purification of navy surplus ingot lithium which is being considered for use in a larger system will be discussed. Finally, the analytical techniques used in our laboratory will be summarized and the results of a recent round robin lithium analysis will be presented

  8. Synthesis and characterization of Cu/sub 11/V/sub 6/O/sub 26/ as high -- capacity cathodes for lithium secondary batteries via a wet chemistry route

    International Nuclear Information System (INIS)

    Yuan, C.; Binqiang, M.A.; Suhong, L.U.

    2009-01-01

    The cathode material of Cu/sub 11/ V/sub 6/O/sub 26/ has been synthesized for the lithium secondary batteries via the wet-chemistry method. The as-prepared powders were characterized by powder X-ray diffraction (XRD), scanning electron microscope (SEM) and laser particle size analysis (LPSA) The electrochemical performances were evaluated by the galvanostatic discharge-charge and cyclic voltammetry technique. These results revealed that Cu/sub 11/ V/sub 6/O/sub 26/ powder could be formed at a temperature as low as 300 degree C, and its particle size was smaller and distributed in a narrower range compared to the other powders synthesized at 400 degree C and 500 degree C. The initial discharge capacity of the powder synthesized at 300 degree C whose D/sub 50/ was only 24.251 macro m was 318.2 mAh/g. It was also found that a severe structure modification of Cu/sub 11/ V/sub 6/ O/sub 26/ powder might take place after the first cycle according to cyclic voltammetry test, which should be responsible for its irreversible capacity. (author)

  9. Mass spectrometric investigation of evaporation of lithium-vanadium bronze

    International Nuclear Information System (INIS)

    Kudin, L.S.; Pogrebnoj, A.M.

    1996-01-01

    The composition of ionic and neutral components of vapour above lithium-vanadium bronze Li 0.2 VO 2.6 has been studied. It is ascertained that molecules of LiVO 3 and O 2 and Li + ions (2.2±0.2); Li + ·LiVO 3 (2.4±0.3); Li + ·(LiVO 3 ) 2 (2.4±0.9); Li + ·V 2 O 5 (2.3±0.9); Cs + (2.1±0.3); Cs + ·LiVO 3 (2.6±1.0) are basic components of saturated vapour, the values of ionic work functions in eV are given in parentheses. Sublimation enthalpy of lithium metavanadate Δ S H 0 (LiVO 3 , 298 K)=457±30 kJ/mol and its formation enthalpy Δ f H 0 (LiVO 3 , gas, 298 k)=-704±30 kJ/mol. have been defined. Using law 2 of thermodynamics the enthalpies of ion-molecular reactions have been defined. ion formation enthalpies being calculated on their basis. 18 refs., 3 figs., 3 tabs

  10. Some peculiarities of interactions of weakly bound lithium nuclei at near-barrier energies

    Science.gov (United States)

    Kabyshev, A. M.; Kuterbekov, K. A.; Sobolev, Yu G.; Penionzhkevich, Yu E.; Kubenova, M. M.; Azhibekov, A. K.; Mukhambetzhan, A. M.; Lukyanov, S. M.; Maslov, V. A.; Kabdrakhimova, G. D.

    2018-02-01

    This paper presents new experimental data on the total cross sections of 9Li + 28Si reactions at low energies as well as the analysis of previously obtained data for 6,7Li. Based on a large collection of data (authors’ and literature data) we carried out a comparative analysis of the two main experimental interaction cross sections (angular distributions of the differential cross sections and total reaction cross sections) for weakly bound lithium (6-9Li, 11Li) nuclei in the framework of Kox parameterization and the macroscopic optical model. We identified specific features of these interactions and predicted the experimental trend in the total reaction cross sections for Li isotopes at energies close to the Coulomb barrier.

  11. Thermogravimetric analysis and kinetic study of formation of lithium titanate by solid state route

    International Nuclear Information System (INIS)

    Sonak, Sagar; Jain, Uttam; Sahu, Ashok Kumar; Kumar, Sanjay; Krishnamurthy, Nagaiyar

    2015-01-01

    The kinetics of formation of lithium titanate from the solid state reaction of lithium carbonate and titanium oxide was studied using non-isothermal thermogravimetric technique. Thermogravimetric data for the reaction of lithium carbonate and titanium oxide was obtained at various heating rates. The methods such as Flynn–Wall–Ozawa and Kissinger–Akahira–Sunose were used to estimate the kinetic parameters from the obtained thermogravimetric data. The average activation energy for the formation of lithium titanate by solid state route was found to be 243 kJ/mol K. The reaction mechanism was determined by the method given by Malek. It was found that the three dimensional diffusion model best describes the reaction kinetics. A kinetic equation describing the reaction is proposed and reaction mechanism is discussed

  12. Isotope analysis of lithium by thermionic mass spectrometry

    International Nuclear Information System (INIS)

    Kakazu, M.H.; Sarkis, J.E.S.

    1991-04-01

    An analytical mass spectrometric method for the isotope analysis of lithium has been studied. The analysis were carried out by using a single focusing thermoionic mass spectrometer Varian Mat TH5 with 90 sup(0) magnetic sector field and 21.4 cm deflection radius, equipped with a dual Re-filament thermal ionization ion source. The effect of different lithium chemical forms, such as, carbonate, chloride, nitrate and sulfate upon the isotopic ratios sup(6)Li/ sup(7)Li has been studied. Isotopic fractionation of lithium was studied in terms of the time of analysis. The results obtained with lithium carbonate yielded a precision of ±0.1% and an accuracy of ± 0.6%, whereas with other chemical forms yielded precisions of ±0.5% and accuracies of ±2%. A fractionation correction factor, K=1.005, was obtained for different samples of lithium carbonate isotopic standard CBNM IRM 016, which has been considered constant. (author)

  13. Challenge in manufacturing electrolyte solutions for lithium and lithium ion batteries quality control and minimizing contamination level

    Science.gov (United States)

    Heider, U.; Oesten, R.; Jungnitz, M.

    The quality of electrolytes for lithium batteries are a major topic in science and battery industries. The solvents and lithium salts should be of highest purity. Therefore, during preparation and handling of electrolyte solutions, the contamination level has to be minimized and the quality during packaging, storage and transportation has to be guaranteed. Especially, protic impurities are found to be very critical for LiPF 6-based electrolytes. The influence of water is reported to be tremendous. But also other protic impurities like alcohols are considered to play an important role in the electrolyte quality. The reaction of the protic impurities with LiPF 6 leads to the formation of HF which further reacts with cathode active materials (e.g., spinel) and the passivating films of the cathode and anode. For a better understanding of the protic impurities and their role in the electrolyte quality a systematic investigation of different impurities was carried out. Electrolytes were doped with different protic compounds. Then the electrolyte was analyzed for protic impurities and HF in dependence of time. First results showing the relation between protic impurities and HF are presented and discussed. In addition, different packaging materials for the electrolyte solutions were investigated. Storage tests were carried out at different temperatures and in different atmospheres. Results on contamination levels, influence of packaging, high temperature storage and handling are addressed.

  14. New studies on the synthesis and structural chemistry of polynary lithium and silver transition metal phosphates

    International Nuclear Information System (INIS)

    Mosymow, Emma

    2015-01-01

    In the course of this work extensive equilibrium studies were carried out in the four-system systems Li / M / P / O (M: Cr, Mn) in the search for new, powerful cathode materials for lithium ion batteries. The phosphates LiCr II 4 (PO 4 ) 3 , NaCr II 4 (PO 4 ) 3 , Li 5 Cr II 2 Cr III (PO 4 ) 4 , monoclines Li 3 Cr 2 (PO 4 ) 3 , Cr II 5 Cr III 2 (P 2 O 7 ) 4 and LiMn II 2 P 3 O 10 were obtained for the first time. The present work reports on their synthesis, crystallographic characterization and their spectroscopic and magnetic properties. The equilibrium studies in the Li / Cr / P / O system led to the elucidation of numerous phase relationships. For example, the coexistence regions LiCr 4 (PO 4 ) 3 / Li 5 Cr 3 (PO 4 ) 4 / Cr 2 O 3 / CrP and Li 9 Cr 3 (PO 4 ) 3 / LiCrP 2 O 7 / CrP. The coexistence of some equilibrium phases such as lithium orthophosphate and lithium manganese(II) orthophosphate as well as lithium metaphosphate and manganese(III) metaphosphate were also investigated in the Li / Mn / P / O system. Furthermore, the de-intercalation behavior of silver manganese phosphates was investigated with the possibility of demonstrating metastable phosphates with manganese in oxidation states higher than 3+. In this case the four-substance system Ag / Mn / P / O with Mn(II) and Mn(III) was considered. The reaction conditions were adapted to those of the experiments in the corresponding lithium-containing systems. Within the scope of the equilibrium studies two new pyrophosphates AgMnP 2 O 7 and Ag 1,6 Mn 3 (P 2 O 7 ) 2 were found and characterized. [de

  15. Optimisation of a quantitative polymerase chain reaction-based strategy for the detection and quantification of human herpesvirus 6 DNA in patients undergoing allogeneic haematopoietic stem cell transplantation

    Directory of Open Access Journals (Sweden)

    Miriam YH Ueda

    2015-06-01

    Full Text Available Human herpesvirus 6 (HHV-6 may cause severe complications after haematopoietic stem cell transplantation (HSCT. Monitoring this virus and providing precise, rapid and early diagnosis of related clinical diseases, constitute essential measures to improve outcomes. A prospective survey on the incidence and clinical features of HHV-6 infections after HSCT has not yet been conducted in Brazilian patients and the impact of this infection on HSCT outcome remains unclear. A rapid test based on real-time quantitative polymerase chain reaction (qPCR has been optimised to screen and quantify clinical samples for HHV-6. The detection step was based on reaction with TaqMan® hydrolysis probes. A set of previously described primers and probes have been tested to evaluate efficiency, sensitivity and reproducibility. The target efficiency range was 91.4% with linearity ranging from 10-106 copies/reaction and a limit of detection of five copies/reaction or 250 copies/mL of plasma. The qPCR assay developed in the present study was simple, rapid and sensitive, allowing the detection of a wide range of HHV-6 loads. In conclusion, this test may be useful as a practical tool to help elucidate the clinical relevance of HHV-6 infection and reactivation in different scenarios and to determine the need for surveillance.

  16. Effect of shrapnel penetration on lithium-carbon monofluoride and lithium-manganese dioxide batteries

    Science.gov (United States)

    Garrard, W. N. C.

    National BR2/3A lithium-carbon monofluoride and Duracell DL2/3A lithium-manganese dioxide batteries were subjected to simulated shrapnel penetration using a projectile from an M16 rifle. Trials were conducted on batteries in various states of charge (0, 50, and 100 percent discharged) in both wet and dry environments. Only one fully charged Duracell Battery (under wet conditions) caught fire during the test. The effects of environmental conditions, the chemical reactions involved, and the state of charge of the batteries on the probability of the batteries igniting are discussed.

  17. Lithium ion storage between graphenes

    Directory of Open Access Journals (Sweden)

    Chan Yue

    2011-01-01

    Full Text Available Abstract In this article, we investigate the storage of lithium ions between two parallel graphene sheets using the continuous approximation and the 6-12 Lennard-Jones potential. The continuous approximation assumes that the carbon atoms can be replaced by a uniform distribution across the surface of the graphene sheets so that the total interaction potential can be approximated by performing surface integrations. The number of ion layers determines the major storage characteristics of the battery, and our results show three distinct ionic configurations, namely single, double, and triple ion forming layers between graphenes. The number densities of lithium ions between the two graphenes are estimated from existing semi-empirical molecular orbital calculations, and the graphene sheets giving rise to the triple ion layers admit the largest storage capacity at all temperatures, followed by a marginal decrease of storage capacity for the case of double ion layers. These two configurations exceed the maximum theoretical storage capacity of graphite. Further, on taking into account the charge-discharge property, the double ion layers are the most preferable choice for enhanced lithium storage. Although the single ion layer provides the least charge storage, it turns out to be the most stable configuration at all temperatures. One application of the present study is for the design of future high energy density alkali batteries using graphene sheets as anodes for which an analytical formulation might greatly facilitate rapid computational results.

  18. Lithium adsorption on amorphous aluminum hydroxides and gibbsite

    OpenAIRE

    Prodromou, Konstantinos P.

    2016-01-01

    Lithium (Li) adsorption on both amorphous aluminum hydroxides and gibbsite was studied. For the amorphous Al(OH)3 the adsorption was found to be pH dependent. Generally, 1.6 times more Li was adsorbed at initial pH value 8.0 compared with pH value 6.50. Gibbsite adsorbed 11.6 to 45.5 times less Li quantities compared with amorphous Al(OH)3. Lithium adsorption was not depended on equilibrium times. It remained stable for all equilibrium times used. Lithium quantities extracted with 1N CH3COONH...

  19. Kinetics Tuning the Electrochemistry of Lithium Dendrites Formation in Lithium Batteries through Electrolytes

    International Nuclear Information System (INIS)

    Tao, Ran; Bi, Xuanxuan; The Ohio State University, Columbus, OH; Li, Shu; Yao, Ying

    2017-01-01

    Lithium batteries are one of the most advance energy storage devices in the world and have attracted extensive research interests. However, lithium dendrite growth was a safety issue which handicapped the application of pure lithium metal in the negative electrode. In this paper, two solvents, propylene carbonate (PC) and 2-methyl-tetrahydrofuran (2MeTHF), and four Li"+ salts, LiPF_6, LiAsF_6, LiBF_4 and LiClO_4 were investigated in terms of their effects on the kinetics of lithium dendrite formation in eight electrolyte solutions. The kinetic parameters of charge transfer step (exchange current density, j_0, transfer coefficient, α) of Li"+/Li redox system, the mass transfer parameters of Li"+ (transfer number of Li"+, t_L_i_+, diffusion coefficient of Li"+, D_L_i_+), and the conductivity (κ) of each electrolyte were studied separately. The results demonstrate that the solvents play a critical role in the measured j_0, t_L_i_+, D_L_i_+, and κ of the electrolyte, while the choice of Li"+ salts only slightly affect the measured parameters. Finally, the understanding of the kinetics will gain insight into the mechanism of lithium dendrite formation and provide guidelines to the future application of lithium metal.

  20. 3D Interconnected V6O13 Nanosheets Grown on Carbonized Textile via a Seed-Assisted Hydrothermal Process as High-Performance Flexible Cathodes for Lithium-Ion Batteries

    Science.gov (United States)

    Xu, Shixing; Cen, Dingcheng; Gao, Peibo; Tang, Huang; Bao, Zhihao

    2018-03-01

    Three-dimensional (3D) free-standing nanostructured materials have been proven to be one of the most promising electrodes for energy storage due to their enhanced electrochemical performance. And they are also widely studied for the wearable energy storage systems. In this work, interconnected V6O13 nanosheets were grown on the flexible carbonized textile (c-textile) via a seed-assisted hydrothermal method to form a 3D free-standing electrode for lithium-ion batteries (LIBs). The electrode exhibited a specific capacity of 170 mA h g-1 at a specific current of 300 mA g-1. With carbon nanotube (CNT) coating, its specific capacities further increased 12-40% at the various current rates. It could retain a reversible capacity of 130 mA h g-1, 74% of the initial capacity after 300 cycles at the specific current of 300 mA g-1. It outperformed most of the mixed-valence vanadium oxides. The improved electrochemical performance was ascribed to the synergistic effect of the 3D nanostructure of V6O13 for feasible Li+ diffusion and transport and highly conductive hierarchical conductive network formed by CNT and carbon fiber in c-textile.

  1. Novel lithium iron phosphate materials for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Popovic, Jelena

    2011-06-15

    Conventional energy sources are diminishing and non-renewable, take million years to form and cause environmental degradation. In the 21st century, we have to aim at achieving sustainable, environmentally friendly and cheap energy supply by employing renewable energy technologies associated with portable energy storage devices. Lithium-ion batteries can repeatedly generate clean energy from stored materials and convert reversely electric into chemical energy. The performance of lithium-ion batteries depends intimately on the properties of their materials. Presently used battery electrodes are expensive to be produced; they offer limited energy storage possibility and are unsafe to be used in larger dimensions restraining the diversity of application, especially in hybrid electric vehicles (HEVs) and electric vehicles (EVs). This thesis presents a major progress in the development of LiFePO4 as a cathode material for lithium-ion batteries. Using simple procedure, a completely novel morphology has been synthesized (mesocrystals of LiFePO4) and excellent electrochemical behavior was recorded (nanostructured LiFePO4). The newly developed reactions for synthesis of LiFePO4 are single-step processes and are taking place in an autoclave at significantly lower temperature (200 deg. C) compared to the conventional solid-state method (multi-step and up to 800 deg. C). The use of inexpensive environmentally benign precursors offers a green manufacturing approach for a large scale production. These newly developed experimental procedures can also be extended to other phospho-olivine materials, such as LiCoPO4 and LiMnPO4. The material with the best electrochemical behavior (nanostructured LiFePO4 with carbon coating) was able to deliver a stable 94% of the theoretically known capacity.

  2. Lithium Resources for the 21st Century

    Science.gov (United States)

    Kesler, S.; Gruber, P.; Medina, P.; Keolian, G.; Everson, M. P.; Wallington, T.

    2011-12-01

    Lithium is an important industrial compound and the principal component of high energy-density batteries. Because it is the lightest solid element, these batteries are widely used in consumer electronics and are expected to be the basis for battery electric vehicles (BEVs), hybrid electric vehicles (HEVs) and plug-in hybrid electric vehicles (PHEVs) for the 21st century. In view of the large incremental demand for lithium that will result from expanded use of various types of EVs, long-term estimates of lithium demand and supply are advisable. For GDP growth rates of 2 to 3% and battery recycling rates of 90 to 100%, total demand for lithium for all markets is expected to be a maximum of 19.6 million tonnes through 2100. This includes 3.2 million tonnes for industrial compounds, 3.6 million tonnes for consumer electronics, and 12.8 million tonnes for EVs. Lithium-bearing mineral deposits that might supply this demand contain an estimated resource of approximately 39 million tonnes, although many of these deposits have not been adequately evaluated. These lithium-bearing mineral deposits are of two main types, non-marine playa-brine deposits and igneous deposits. Playa-brine deposits have the greatest immediate resource potential (estimated at 66% of global resources) and include the Salar de Atacama (Chile), the source of almost half of current world lithium production, as well as Zabuye (China/Tibet) and Hombre Muerto (Argentina). Additional important playa-brine lithium resources include Rincon (Argentina), Qaidam (China), Silver Peak (USA) and Uyuni (Bolivia), which together account for about 35% of the estimated global lithium resource. Information on the size and continuity of brine-bearing aquifers in many of these deposits is limited, and differences in chemical composition of brines from deposit to deposit require different extraction processes and yield different product mixes of lithium, boron, potassium and other elements. Numerous other brines in playas

  3. Spectator invariance test in the study of the Trojan Horse Method 6,7Li fusion reactions via the Trojan Horse Method

    Directory of Open Access Journals (Sweden)

    Li C.

    2011-10-01

    Full Text Available Fusion reactions play a crucial role for several astrophysical scenarios. At the low energies typical of such environments direct measurements of reaction cross sections are very difficult, and even sometimes impossible. In such cases the use of indirect methods can give a substantial help. The Trojan Horse Method (THM is based on the quasi-free break-up of a nucleus, which can be described in terms of a cluster structure. In such applications the independence of THM results with different break-up schemes, was tested using the quasi free3 He(6Li,ααH and 3He(7Li,αα2H reactions. Results were then compared with the direct behaviours obtained from available data as well as with the cross sections extracted from previous indirect investigations of the same binary reactions using a different nuclide as a Trojan Horse nucleus.

  4. Electronic properties of lithium titanate ceramic

    International Nuclear Information System (INIS)

    Padilla-Campos, Luis; Buljan, Antonio

    2001-01-01

    Research on tritium breeder material is fundamental to the development of deuterium-tritium type fusion reactors for producing clean, non contaminating, electrical energy, since only energy and helium, a harmless gas, are produced from the fusion reaction. Lithium titanate ceramic is one of the possible candidates for the tritium breeder material. This last material is thought to form part of the first wall of the nucleus of the reactor which will provide the necessary tritium for the fusion and will also serve as a shield. Lithium titanate has advantageous characteristics compared to other materials. Some of these are low activation under the irradiation of neutrons, good thermal stability, high density of lithium atoms and relatively fast tritium release at low temperatures. However, there are still several physical and chemical properties with respect to the tritium release mechanism and mechanical properties that have not been studied at all. This work presents a theoretical study of the electronic properties of lithium titanate ceramic and the corresponding tritiated material. Band calculations using the Extended H kel Tight-Binding approach were carried out. Results show that after substituting lithium for tritium atoms, the electronic states for the latter appear in the middle of prohibited band gap which it is an indication that the tritiated material should behave as a semiconductor, contrary to Li 2 TiO 3 which is a dielectric isolator. A study was also carried out to determine the energetically most favorable sites for the substitution of lithium for tritium atoms. Additionally, we analyzed possible pathways for the diffusion of a tritium atom within the crystalline structure of the Li 2 TiO 3

  5. A global model for SF6 plasmas coupling reaction kinetics in the gas phase and on the surface of the reactor walls

    International Nuclear Information System (INIS)

    Kokkoris, George; Panagiotopoulos, Apostolos; Gogolides, Evangelos; Goodyear, Andy; Cooke, Mike

    2009-01-01

    Gas phase and reactor wall-surface kinetics are coupled in a global model for SF 6 plasmas. A complete set of gas phase and surface reactions is formulated. The rate coefficients of the electron impact reactions are based on pertinent cross section data from the literature, which are integrated over a Druyvesteyn electron energy distribution function. The rate coefficients of the surface reactions are adjustable parameters and are calculated by fitting the model to experimental data from an inductively coupled plasma reactor, i.e. F atom density and pressure change after the ignition of the discharge. The model predicts that SF 6 , F, F 2 and SF 4 are the dominant neutral species while SF 5 + and F - are the dominant ions. The fit sheds light on the interaction between the gas phase and the reactor walls. A loss mechanism for SF x radicals by deposition of a fluoro-sulfur film on the reactor walls is needed to predict the experimental data. It is found that there is a net production of SF 5 , F 2 and SF 6 , and a net consumption of F, SF 3 and SF 4 on the reactor walls. Surface reactions as well as reactions between neutral species in the gas phase are found to be important sources and sinks of the neutral species.

  6. On anodic stability and decomposition mechanism of sulfolane in high-voltage lithium ion battery

    International Nuclear Information System (INIS)

    Xing, Lidan; Tu, Wenqiang; Vatamanu, Jenel; Liu, Qifeng; Huang, Wenna; Wang, Yating; Zhou, Hebing; Zeng, Ronghua; Li, Weishan

    2014-01-01

    Graphical abstract: - Highlights: • Influence of lithium salts on the anodic stability of sulfolane has been investigated. • Oxidation decomposition mechanisms of LiPF 6 /Sulfolane electrolyte have been well understood by theoretical and experimental methods. • Decomposition products of the electrolyte can be found on the electrode surface and in the interfacial electrolyte. - Abstract: In this work, we investigated the anodic stability and decomposition mechanism of sulfolane (SL). The anodic stability of SL-based electrolyte with different lithium salts on Pt and LiNi 0.5 Mn 1.5 O 4 electrodes was found to decrease as follows: LiPF 6 /SL > LiBF 4 /SL > LiClO 4 /SL. The oxidation potential of 1M LiPF 6 /SL electrolyte on both Pt and electrodes is about 5.0V vs Li/Li + . The presence of PF 6 - and another SL solvent dramatically alters the decomposition mechanism of SL. Oxidation decomposition of SL-SL cluster is the most favorable reaction in LiPF 6 /SL electrolyte. The dimer products with S-O-R group were detected by IR spectra on the charged LiNi 0.5 Mn 1.5 O 4 electrode surface and in the electrolyte near the electrode surface, and were found to increase the interfacial reaction resistance of the LiNi 0.5 Mn 1.5 O 4 electrode

  7. Upper limits to the reaction rate coefficients of C(n)(-) and C(n)H(-) (n = 2, 4, 6) with molecular hydrogen.

    Science.gov (United States)

    Endres, Eric S; Lakhmanskaya, Olga; Hauser, Daniel; Huber, Stefan E; Best, Thorsten; Kumar, Sunil S; Probst, Michael; Wester, Roland

    2014-08-21

    In the interstellar medium (ISM) ion–molecule reactions play a key role in forming complex molecules. Since 2006, after the radioastronomical discovery of the first of by now six interstellar anions, interest has grown in understanding the formation and destruction pathways of negative ions in the ISM. Experiments have focused on reactions and photodetachment of the identified negatively charged ions. Hints were found that the reactions of CnH(–) with H2 may proceed with a low (rate [Eichelberger, B.; et al. Astrophys. J. 2007, 667, 1283]. Because of the high abundance of molecular hydrogen in the ISM, a precise knowledge of the reaction rate is needed for a better understanding of the low-temperature chemistry in the ISM. A suitable tool to analyze rare reactions is the 22-pole radiofrequency ion trap. Here, we report on reaction rates for Cn(–) and CnH(–) (n = 2, 4, 6) with buffer gas temperatures of H2 at 12 and 300 K. Our experiments show the absence of these reactions with an upper limit to the rate coefficients between 4 × 10(–16) and 5 × 10(–15) cm(3) s(–1), except for the case of C2(–), which does react with a finite rate with H2 at low temperatures. For the cases of C2H(–) and C4H(–), the experimental results were confirmed with quantum chemical calculations. In addition, the possible influence of a residual reactivity on the abundance of C4H(–) and C6H(–) in the ISM were estimated on the basis of a gas-phase chemical model based on the KIDA database. We found that the simulated ion abundances are already unaffected if reaction rate coefficients with H2 were below 10(–14) cm(3) s(–1).

  8. Controlled Radical Polymerisation of Styrene in the Presence of Lithium Molybdate(V) Complexes and Benzylic Halides

    NARCIS (Netherlands)

    Koten, G. van; Brandts, J.A.M.; Geijn, P. van de; Faassen, E.E.H. van; Boersma, J.

    1999-01-01

    The new lithium molybdate(V) complexes [LiMo(NAr){2}(C-N)R] (C-N=C{6}H{4}(CH{2}NMe{2})-2; R=(C-N) (5), Me (6), CH{2}SiMe{3} (7), p-tolyl (8)), have been generated in situ from reaction of the corresponding molybdenum(VI) complexes [Mo(NAr){2}(C-N)R] (C-N=C{6}H{4}(CH{2}NMe{2})-2; R=(C-N) (1), Me (2),

  9. Study of NaBH4 reaction with RhCl3·4H2O and H2PtCl6·6H2O in dimethylformamide

    International Nuclear Information System (INIS)

    Khain, V.S.; Val'kova, V.P.

    1988-01-01

    Data on study of NaBH 4 reactions with RhCl 3 x4H 2 O and H 2 PtCl 6 x6H 2 O in dimethylformamide, which is a good solvent of both complex hydride and compounds of platinum metals are presented. Rhodium (3) and platinum (4) reduction by sodium tetrahydridoborate in dimethylformamide proceeds quantitatively up to element state. Depositions of powder-like rhodium and platinum or their sols stable up to 8 months are formed depending on the ratio of concentrations of the reacting substances. Stoichiometry of redox-reactions is established based on spectrophotometric, gasovolumetric measurements,

  10. Carbon nanofibers (CNFs) supported cobalt- nickel sulfide (CoNi2S4) nanoparticles hybrid anode for high performance lithium ion capacitor.

    Science.gov (United States)

    Jagadale, Ajay; Zhou, Xuan; Blaisdell, Douglas; Yang, Sen

    2018-01-25

    Lithium ion capacitors possess an ability to bridge the gap between lithium ion battery and supercapacitor. The main concern of fabricating lithium ion capacitors is poor rate capability and cyclic stability of the anode material which uses sluggish faradaic reactions to store an electric charge. Herein, we have fabricated high performance hybrid anode material based on carbon nanofibers (CNFs) and cobalt-nickel sulfide (CoNi 2 S 4 ) nanoparticles via simple electrospinning and electrodeposition methods. Porous and high conducting CNF@CoNi 2 S 4 electrode acts as an expressway network for electronic and ionic diffusion during charging-discharging processes. The effect of anode to cathode mass ratio on the performance has been studied by fabricating lithium ion capacitors with different mass ratios. The surface controlled contribution of CNF@CoNi 2 S 4 electrode was 73% which demonstrates its excellent rate capability. Lithium ion capacitor fabricated with CNF@CoNi 2 S 4 to AC mass ratio of 1:2.6 showed excellent energy density of 85.4 Wh kg -1 with the power density of 150 W kg -1 . Also, even at the high power density of 15 kW kg -1 , the cell provided the energy density of 35 Wh kg -1 . This work offers a new strategy for designing high-performance hybrid anode with the combination of simple and cost effective approaches.

  11. The Science of Electrode Materials for Lithium Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Fultz, Brent

    2007-03-15

    Rechargeable lithium batteries continue to play the central role in power systems for portable electronics, and could play a role of increasing importance for hybrid transportation systems that use either hydrogen or fossil fuels. For example, fuel cells provide a steady supply of power, whereas batteries are superior when bursts of power are needed. The National Research Council recently concluded that for dismounted soldiers "Among all possible energy sources, hybrid systems provide the most versatile solutions for meeting the diverse needs of the Future Force Warrior. The key advantage of hybrid systems is their ability to provide power over varying levels of energy use, by combining two power sources." The relative capacities of batteries versus fuel cells in a hybrid power system will depend on the capabilities of both. In the longer term, improvements in the cost and safety of lithium batteries should lead to a substantial role for electrochemical energy storage subsystems as components in fuel cell or hybrid vehicles. We have completed a basic research program for DOE BES on anode and cathode materials for lithium batteries, extending over 6 years with a 1 year phaseout period. The emphasis was on the thermodynamics and kinetics of the lithiation reaction, and how these pertain to basic electrochemical properties that we measure experimentally — voltage and capacity in particular. In the course of this work we also studied the kinetic processes of capacity fade after cycling, with unusual results for nanostructued Si and Ge materials, and the dynamics underlying electronic and ionic transport in LiFePO4. This document is the final report for this work.

  12. In-situ measurement of the lithium distribution in Li-ion batteries using micro-IBA techniques

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, A., E-mail: yamazaki@tac.tsukuba.ac.jp [Faculty of Pure and Applied Sciences, University of Tsukuba, 1-1-1 Tennodai, Tsukuba, Ibaraki 305-8577 (Japan); Orikasa, Y.; Chen, K.; Uchimoto, Y. [Graduate School of Human and Environmental Studies, Kyoto University, Yoshida-nihonmatsucho, Sakyo-ku, Kyoto 606-8501 (Japan); Kamiya, T.; Koka, M.; Satoh, T. [Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA), 1233, Watanuki-machi, Takasaki, Gunma 370-1292 (Japan); Mima, K.; Kato, Y.; Fujita, K. [The Graduate School for the Creation of New Photonics Industries, 1955-1, Kurematsu, NIshi-ku, Hamamatsu, Shizuoka 431-1202 (Japan)

    2016-03-15

    Direct observation of lithium concentration distribution in lithium-ion battery composite electrodes has been performed for the first time. Lithium-ion battery model cells for particle induced X-ray emission (PIXE) and particle induced gamma ray emission (PIGE) measurements were designed and fabricated. Two dimensional images of lithium concentration in LiFePO{sub 4} composite electrodes were obtained with PIXE and PIGE by scanning the proton microbeam for various charged states of the electrodes. Lithium concentration in LiFePO{sub 4} composite electrodes was decreased from the contact interface between LiFePO{sub 4} electrode and liquid electrolyte during the charge reaction.

  13. In-situ measurement of the lithium distribution in Li-ion batteries using micro-IBA techniques

    International Nuclear Information System (INIS)

    Yamazaki, A.; Orikasa, Y.; Chen, K.; Uchimoto, Y.; Kamiya, T.; Koka, M.; Satoh, T.; Mima, K.; Kato, Y.; Fujita, K.

    2016-01-01

    Direct observation of lithium concentration distribution in lithium-ion battery composite electrodes has been performed for the first time. Lithium-ion battery model cells for particle induced X-ray emission (PIXE) and particle induced gamma ray emission (PIGE) measurements were designed and fabricated. Two dimensional images of lithium concentration in LiFePO_4 composite electrodes were obtained with PIXE and PIGE by scanning the proton microbeam for various charged states of the electrodes. Lithium concentration in LiFePO_4 composite electrodes was decreased from the contact interface between LiFePO_4 electrode and liquid electrolyte during the charge reaction.

  14. A detailed study of lithium in 107 CHEPS dwarf stars

    Science.gov (United States)

    Pavlenko, Ya. V.; Jenkins, J. S.; Ivanyuk, O. M.; Jones, H. R. A.; Kaminsky, B. M.; Lyubchik, Yu. P.; Yakovina, L. A.

    2018-03-01

    Context. We report results from lithium abundance determinations using high resolution spectral analysis of the 107 metal-rich stars from the Calan-Hertfordshire Extrasolar Planet Search programme. Aims: We aim to set out to understand the lithium distribution of the population of stars taken from this survey. Methods: The lithium abundance taking account of non-local thermodynamical equilibrium effects was determined from the fits to the Li I 6708 Å resonance doublet profiles in the observed spectra. Results: We find that a) fast rotators tend to have higher lithium abundances; b) log N(Li) is higher in more massive and hot stars; c) log N(Li) is higher in stars of lower log g; d) stars with the metallicities >0.25 dex do not show the lithium lines in their spectra; e) most of our planet hosts rotate slower; and f) a lower limit of lithium isotopic ratio is 7Li/6Li > 10 in the atmospheres of two stars with planets (SWP) and two non-SWP stars. Conclusions: Measurable lithium abundances were found in the atmospheres of 45 stars located at distances of 20-170 pc from the Sun, for the other 62 stars the upper limits of log N(Li) were computed. We found well defined dependences of lithium abundances on Teff, V sin i, and less pronounced for the log g. In case of V sin i we see two sequences of stars: with measurable lithium and with the upper limit of log N(Li). About 10% of our targets are known to host planets. Only two SWP have notable lithium abundances, so we found a lower proportion of stars with detectable Li among known planet hosts than among stars without planets. However, given the small sample size of our planet-host sample, our analysis does not show any statistically significant differences in the lithium abundance between SWP and stars without known planets.

  15. The preparation of lithium aluminate by the hydrolysis of lithium and aluminum alkoxides

    International Nuclear Information System (INIS)

    Turner, C.W.; Clatworthy, B.C.; Gin, A.Y.H.

    1987-10-01

    Lithium aluminate was prepared by heating the hydrolysis products from various combinations of lithium and aluminum alkoxides under an atmosphere of nitrogen. The product was β-LiA1O 2 when aluminum iso-propoxide was a starting material, whereas γ-LiA1O 2 was the product for preparations starting with aluminum n-butoxide. The results were independent of the choice of lithium alkoxide. The hydrolysis of aluminum sec-butoxide with a solution of LiOH led to the γ phase as well. The temperature at which the γ phase developed depended upon the conditions of the hydrolysis reaction and was observed at a temperature as low as 550 degrees Celcius

  16. Lithium adsorption by the first wall of fusion reactor-tokamak

    International Nuclear Information System (INIS)

    Bakunin, O.G.

    1989-01-01

    Lithium adsorption by the first wall of fusion reactor under stationary conditions and in the absence of chemical reactions is considered. Possibility of achieving 70% coating of the wall with lithium which can lead to sufficient decrease of sputtering is shown. 5 refs.; 5 figs

  17. Synthesis and structural characterization of defect spinels in the Lithium-Manganese-Oxide system

    CSIR Research Space (South Africa)

    Thackeray, MM

    1993-10-01

    Full Text Available Lithium-manganese-oxides prepared at moderate temperatures are under investigation as insertion electrodes for rechargeable lithium batteries. The structures of two defect-spinel compounds synthesised by the reaction of MnCO3 and Li2CO3 at 400...

  18. Synthesis and structural characterization of defect spinels in the lithium-manganese-oxide system

    CSIR Research Space (South Africa)

    Thackeray, MM

    1993-10-01

    Full Text Available Lithium-manganese-oxides prepared at moderate temperatures are under investigation as insertion electrodes for rechargeable lithium batteries. The structures of two defect-spinel compounds synthesized by the reaction of MnCO3 and Li2CO3 at 400°C...

  19. Evidence for leading mesons in anti p sup 4 He reactions at 0. 6 GeV c sup -1 incident momentum

    Energy Technology Data Exchange (ETDEWEB)

    Balestra, F.; Bossolasco, S.; Bussa, M.P.; Busso, L.; Fava, L.; Ferrero, L.; Grasso, A.; Maggiora, A.; Panzieri, D.; Piragino, G.; Piragino, R.; Tosello, F. (Ist. di Fisica Generale ' A. Avogadro' , Univ. of Turin (Italy) INFN, Sezione di Torino (Italy)); Bendiscioli, G.; Filippini, V.; Rotondi, A.; Salvini, P.; Venaglioni, A.; Zenoni, A. (Dipt. di Fisica Nucleare e Teoria, Univ. of Pavia (Italy) INFN, Sezione di Pavia (Italy)); Batusov, Yu.; Bunyatov, S.A.; Falomkin, I.V.; Nichitiu, F.; Pontecorvo, G.B.; Rozhdestvensky, A.M.; Sapozhnikov, M.G.; Tretyak, V.I. (Joint Inst. of Nuclear Research, Dubna (USSR)); Guaraldo, C. (Lab. Nazionali di Frascati dell' INFN (Italy)); Lodi Rizzini, E. (Dipt. di Automazione Industriale, Univ. of Brescia (Italy) INFN, Sezione di Pavia (Italy)); Haatuft, A.; Halsteinslid, A.; Myklebost, K.; Olsen, J.M. (Physics Dept., Univ. of Bergen (Norway)); Breivik, F.O.; Danielsen, K.M.; Jacobsen, T.; Soerensen, S.O. (Inst. of Physics, Univ. of Oslo (Norway))

    1991-01-01

    Leading mesons are seen in anti p {sup 4}He {yields} neutral strange particles at 0.6 GeV c{sup -1} incident momentum. These results differ somewhat from our previous results from anti p Ne-reactions. The concept of an ''effective target'' is useless. (orig.).

  20. Note on possible glueball production in anti p4He reactions at 0.6 GeV/c incident momentum

    International Nuclear Information System (INIS)

    Breivik, F.O.; Haatuft, A.; Halsteinslid, A.

    1990-10-01

    The invariant mass distribution of six-particle systems in the final states of anti p 4 He-reactions at 0.6 GeV/c incident momentum shows two narrow peaks at about 1500 and 1850 MeV/c 2 which may be due to the production of glueballs. 12 refs., 4 figs

  1. High Pressure Diels Alder Reactions of 1-Vinyl-2,2,6-trimethylcyclohexene Catalyzed by Chiral Lewis Acids; An Enantioselective Route to a Drimane Sesquiterpene Precursor.

    NARCIS (Netherlands)

    Knol, Joop; Meetsma, Auke; Feringa, Bernard

    1995-01-01

    The Diels Alder reaction of 1-vinyl-2,2,6-trimethylcyclohexene and 3-((E)-3-(methoxycarbonyl)propenoyl)-1,3-oxazolidin-2-one under high pressure, catalyzed by a chiral bis-imine copper(II) complex, yields a drimane sesquiterpene precursor in a highly regio- and diastereoselective manner with

  2. Domino Aza-Michael-ih-Diels-Alder Reaction to Various 3-Vinyl-1,2,4-triazines: Access to Polysubstituted Tetrahydro-1,6-naphthyridines.

    Science.gov (United States)

    Jouha, Jabrane; Buttard, Floris; Lorion, Magali; Berthonneau, Clément; Khouili, Mostafa; Hiebel, Marie-Aude; Guillaumet, Gérald; Brière, Jean-François; Suzenet, Franck

    2017-09-15

    A straightforward domino aza-Michael-inverse-electron-demand-hetero-Diels-Alder/retro-Diels-Alder reaction between primary and secondary propargylamine derivatives and 3-vinyl-1,2,4-triazines is developed highlighting not only the uniqueness of this dual-heterocyclic platform but also a novel and unprecedented path to polysubstituted tetrahydro-1,6-naphthyridine scaffolds.

  3. Human bone marrow-derived mesenchymal cell reactions to 316L stainless steel : An in vitro study on cell viability and interleukin-6 expression

    NARCIS (Netherlands)

    Anwar, I.B.; Santoso, A.; Saputra, E.; Ismail, R.; Jamari, J.; van der Heide, E.

    2017-01-01

    Purpose: Human bone marrow-derived mesenchymal cell (hBMC) reactions to 316L stainless steel (316L-SS) have never been evaluated. The objective of this study was to assess cell viability and interleukin-6 expression of hBMC cultures upon treatment with a 316L-SS implant. Methods: A cytotoxicity

  4. Study of the reactions 9Be(p, α)6Li, 9Be(p,d)8Be from 300 keV to 900 keV

    International Nuclear Information System (INIS)

    Bertrand, F.; Grenier, G.; Pornet, J.

    1968-10-01

    The experimental results concerning the two reactions 9 Be(p,α) 6 Li and 9 Be(p,d) 8 Be from 300 to 900 keV are presented. The angular distribution, excitation and total cross-section curves are expressed in absolute values after a normalization carried out using results given by Weber, Davis and Marion. (authors) [fr

  5. Reaction of N-(Per-O-acetyl-β-D-glucopyranosyl-Nʼ-(4ʼ,6ʼ-diarylpyrimidine-2ʼ-ylthioureas with Ethyl Bromoacetate

    Directory of Open Access Journals (Sweden)

    Nguyen Dinh Thanh

    2011-01-01

    Full Text Available Some new 2-iminothiazolidin-4-ones having pyrimidine ring have been synthesized by reaction of substituted N-(per-O-acetyl-β-D-glucopyranosyl-Nʼ-(4ʼ,6ʼ-diarylpyrimidine-2ʼ-ylthioureas with ethyl bromoacetate. The structure of isomeric products has been confirmed by spectroscopic methods, such as IR, 1H and 13C NMR.

  6. Hadron correlations in nuclear reactions with production of cumulative protons induced by π- mesons with momentum of 6.0 GeV/c

    International Nuclear Information System (INIS)

    Bayukov, Yu.D.; Vlasov, A.V.; Gavrilov, V.B.

    1981-01-01

    Hardonic correlations were investigated in reactions with the proton backward production induced by 6.0-GeV/c π - mesons on nuclei Be, C, Al, Cu, Cd, Pb, U. The studied correlations indicate an essential role of multiple interactions of the incident particle in production of cumulative protons [ru

  7. Forward absolute cross-section of the reaction 2H(d,n)3He for Esub(d) = (3/6)MeV

    International Nuclear Information System (INIS)

    Pavan, P.; Toniolo, D.; Zago, G.; Zannoni, R.; Galeazzi, G.

    1981-01-01

    The zero-degree differential cross-section of the reaction 2 H(d,n) 3 He was measured, by means of a recoil-proton neutron counter telescope, with an accuracy of 2%, in the incident-deuteron energy interval from 3 to 6 MeV. (author)

  8. Forward absolute cross-section of the reaction /sup 2/H(d,n)/sup 3/He for Esub(d) = (3/6)MeV

    Energy Technology Data Exchange (ETDEWEB)

    Pavan, P.; Toniolo, D.; Zago, G.; Zannoni, R. (Padua Univ. (Italy). Ist. di Fisica); Galeazzi, G.

    1981-12-01

    The zero-degree differential cross-section of the reaction /sup 2/H(d,n)/sup 3/He was measured, by means of a recoil-proton neutron counter telescope, with an accuracy of 2%, in the incident-deuteron energy interval from 3 to 6 MeV.

  9. Forward absolute cross section of the reaction /sup 2/H(d,n)/sup 3/He from E/sub d/ = 3 to 6 MeV

    Energy Technology Data Exchange (ETDEWEB)

    Galeazzi, G.; Pavan, P.; Toniolo, D.; Zago, G.; Zannoni, R.

    1981-01-15

    The zero degree differential cross section of the reaction /sup 2/H(d,n)/sup 3/He was measured, by means of a proton recoil neutron counter telescope, with an accuracy of 2%, in the incident deuteron energy interval from 3 to 6 MeV. Results are presented.

  10. Forward absolute cross-section of the reaction /sup 2/H(d,n)/sup 3/He for Esub(d)=(3/6)MeV

    Energy Technology Data Exchange (ETDEWEB)

    Pavan, P.; Toniolo, D.; Zago, G.; Zannoni, R. (Padua Univ. (Italy). Ist. di Fisica; Istituto Nazionale di Fisica Nucleare, Padua (Italy)); Galeazzi, G. (Istituto Nazionale di Fisica Nucleare, Padua (Italy). Lab. di Legnaro)

    1981-12-01

    The zero-degree differential cross-section of the reaction /sup 2/H(d,n)/sup 3/He was measured, by means of a recoil-proton neutron counter telescope, with an accuracy of 2%, in the incident deuteron energy interval form 3 to 6 MeV.

  11. Characterization of LT-LiXO1-YNIYO2 electrodes for rechargeable lithium cells

    CSIR Research Space (South Africa)

    Gummow, RJ

    1993-12-01

    Full Text Available -spinel in character and that LT- Li0.4Co0.sNi0.102 is a defect spinel with spinel notation {Li0.s\\[:\\]0.2}sa \\[Co, 6Nio.2D0.2104. Electrochemical data.--The charge and discharge pro- files for the first four cycles of Li/LT-LiCoO2, Li... on the B sites of an A\\[B2104 spinel structure. The spinel phase is significantly more stable to lithium insertion/extraction reactions than the quasi-spinel phase. It is believed that by optimizing the processing conditions...

  12. Study of the possibility of solving cosmological lithium problem in an accelerator experiment

    Energy Technology Data Exchange (ETDEWEB)

    Bystritsky, V. M., E-mail: bystvm@jinr.ru [Joint Institute for Nuclear Research (Russian Federation); Varlachev, V. A.; Dudkin, G. N. [National Research Tomsk Polytechnic University (Russian Federation); Krylov, A. R. [Joint Institute for Nuclear Research (Russian Federation); Gazi, S.; Guran, J. [Slovak Academy of Sciences, Institute of Electrical Engineering (Slovakia); Nechaev, B. A.; Padalko, V. N. [National Research Tomsk Polytechnic University (Russian Federation); Sadovsky, A. B. [Joint Institute for Nuclear Research (Russian Federation); Tuleushev, Yu. Zh. [Ministry of Energy of the Republic of Kazakhstan, Nuclear Physics Institute (Kazakhstan); Filipowicz, M. [AGH University of Science and Technology, Faculty of Energy and Fuels (Poland); Philippov, A. V. [Joint Institute for Nuclear Research (Russian Federation)

    2017-03-15

    Within the standar dmodel of Big Bang Nucleosynthesis (BBN), there is a cosmological lithium problem, which consists in a substantial difference between calculated data on the abundances of the isotopes {sup 6}Li and {sup 7}Li and those that were found from observational astronomy. An attempt at measuring the cross section for the main 6Li production reaction {sup 2}H({sup 4}He, γ){sup 6}Li induced by the interaction of {sup 4}He{sup +} ions with deuterons at collision energies less than the lower boundary of the BBN energy range was made in the present study. Upper limits on the cross sections for the reaction in question were set.

  13. An Intramolecular Heck reaction that Prefers a 5-endo- to a 6-exo-trig Cyclization Pathway

    DEFF Research Database (Denmark)

    Vital, Paulo; Norrby, Per-Ola; Tanner, David Ackland

    2006-01-01

    A regioselective aromatic Claisen rearrangement was used to prepare 17a, the precursor of triflate 17e. The intramolecular Heck reaction of 17e is promoted only by bidentate phosphine ligands, giving exclusively and in excellent yield 20, the product of a 5-endo-trig cyclization, despite the poss......A regioselective aromatic Claisen rearrangement was used to prepare 17a, the precursor of triflate 17e. The intramolecular Heck reaction of 17e is promoted only by bidentate phosphine ligands, giving exclusively and in excellent yield 20, the product of a 5-endo-trig cyclization, despite...

  14. Recovery of lithium and cobalt from waste lithium ion batteries of mobile phone.

    Science.gov (United States)

    Jha, Manis Kumar; Kumari, Anjan; Jha, Amrita Kumari; Kumar, Vinay; Hait, Jhumki; Pandey, Banshi Dhar

    2013-09-01

    In view of the stringent environmental regulations, availability of limited natural resources and ever increasing need of alternative energy critical elements, an environmental eco-friendly leaching process is reported for the recovery of lithium and cobalt from the cathode active materials of spent lithium-ion batteries of mobile phones. The experiments were carried out to optimize the process parameters for the recovery of lithium and cobalt by varying the concentration of leachant, pulp density, reductant volume and temperature. Leaching with 2M sulfuric acid with the addition of 5% H(2)O(2) (v/v) at a pulp density of 100 g/L and 75°C resulted in the recovery of 99.1% lithium and 70.0% cobalt in 60 min. H(2)O(2) in sulfuric acid solution acts as an effective reducing agent, which enhance the percentage leaching of metals. Leaching kinetics of lithium in sulfuric acid fitted well to the chemical controlled reaction model i.e. 1-(1-X)(1/3)=k(c)t. Leaching kinetics of cobalt fitted well to the model 'ash diffusion control dense constant sizes spherical particles' i.e. 1-3(1-X)(2/3)+2(1-X)=k(c)t. Metals could subsequently be separated selectively from the leach liquor by solvent extraction process to produce their salts by crystallization process from the purified solution. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. Synthesis and Electrochemical Performance of a Lithium Titanium Phosphate Anode for Aqueous Lithium-Ion Batteries

    KAUST Repository

    Wessells, Colin

    2011-01-01

    Lithium-ion batteries that use aqueous electrolytes offer safety and cost advantages when compared to today\\'s commercial cells that use organic electrolytes. The equilibrium reaction potential of lithium titanium phosphate is -0.5 V with respect to the standard hydrogen electrode, which makes this material attractive for use as a negative electrode in aqueous electrolytes. This material was synthesized using a Pechini type method. Galvanostatic cycling of the resulting lithium titanium phosphate showed an initial discharge capacity of 115 mAh/g and quite good capacity retention during cycling, 84% after 100 cycles, and 70% after 160 cycles at a 1 C cycling rate in an organic electrolyte. An initial discharge capacity of 113 mAh/g and capacity retention of 89% after 100 cycles with a coulombic efficiency above 98% was observed at a C/5 rate in pH -neutral 2 M Li2 S O4. The good cycle life and high efficiency in an aqueous electrolyte demonstrate that lithium titanium phosphate is an excellent candidate negative electrode material for use in aqueous lithium-ion batteries. © 2011 The Electrochemical Society.

  16. Kinetic study of lithium-cadmium ternary amalgam decomposition

    International Nuclear Information System (INIS)

    Cordova, M.H.; Andrade, C.E.

    1992-01-01

    The effect of metals, which form stable lithium phase in binary alloys, on the formation of intermetallic species in ternary amalgams and their effect on thermal decomposition in contact with water is analyzed. Cd is selected as ternary metal, based on general experimental selection criteria. Cd (Hg) binary amalgams are prepared by direct contact Cd-Hg, whereas Li is formed by electrolysis of Li OH aq using a liquid Cd (Hg) cathodic well. The decomposition kinetic of Li C(Hg) in contact with 0.6 M Li OH is studied in function of ageing and temperature, and these results are compared with the binary amalgam Li (Hg) decomposition. The decomposition rate is constant during one hour for binary and ternary systems. Ageing does not affect the binary systems but increases the decomposition activation energy of ternary systems. A reaction mechanism that considers an intermetallic specie participating in the activated complex is proposed and a kinetic law is suggested. (author)

  17. Lithium niobate packaging challenges

    International Nuclear Information System (INIS)

    Murphy, E.J.; Holmes, R.J.; Jander, R.B.; Schelling, A.W.

    1988-01-01

    The use of lithium niobate integrated optic devices outside of the research laboratory is predicated on the development of a sound packaging method. The authors present a discussion of the many issues that face the development of a viable, robust packaging technology. The authors emphasize the interaction of lithium niobate's physical properties with available packaging materials and technologies. The broad range of properties (i.e. electro-optic, piezo-electric, pyro-electric, photorefractive...) that make lithium niobate an interesting material in many device applications also make it a packaging challenge. The package design, materials and packaging technologies must isolate the device from the environment so that lithium niobate's properties do not adversely affect the device performance

  18. High-Performance Lithium-Oxygen Battery Electrolyte Derived from Optimum Combination of Solvent and Lithium Salt.

    Science.gov (United States)

    Ahn, Su Mi; Suk, Jungdon; Kim, Do Youb; Kang, Yongku; Kim, Hwan Kyu; Kim, Dong Wook

    2017-10-01

    To fabricate a sustainable lithium-oxygen (Li-O 2 ) battery, it is crucial to identify an optimum electrolyte. Herein, it is found that tetramethylene sulfone (TMS) and lithium nitrate (LiNO 3 ) form the optimum electrolyte, which greatly reduces the overpotential at charge, exhibits superior oxygen efficiency, and allows stable cycling for 100 cycles. Linear sweep voltammetry (LSV) and differential electrochemical mass spectrometry (DEMS) analyses reveal that neat TMS is stable to oxidative decomposition and exhibit good compatibility with a lithium metal. But, when TMS is combined with typical lithium salts, its performance is far from satisfactory. However, the TMS electrolyte containing LiNO 3 exhibits a very low overpotential, which minimizes the side reactions and shows high oxygen efficiency. LSV-DEMS study confirms that the TMS-LiNO 3 electrolyte efficiently produces NO 2 - , which initiates a redox shuttle reaction. Interestingly, this NO 2 - /NO 2 redox reaction derived from the LiNO 3 salt is not very effective in solvents other than TMS. Compared with other common Li-O 2 solvents, TMS seems optimum solvent for the efficient use of LiNO 3 salt. Good compatibility with lithium metal, high dielectric constant, and low donicity of TMS are considered to be highly favorable to an efficient NO 2 - /NO 2 redox reaction, which results in a high-performance Li-O 2 battery.

  19. Foamlike porous spinel Mn(x)Co(3-x)O4 material derived from Mn3[Co(CN)6]2⋅nH2O nanocubes: a highly efficient anode material for lithium batteries.

    Science.gov (United States)

    Hu, Lin; Zhang, Ping; Zhong, Hao; Zheng, Xinrui; Yan, Nan; Chen, Qianwang

    2012-11-19

    A new facile strategy has been designed to fabricate spinel Mn(x)Co(3-x)O(4) porous nanocubes, which involves a morphology-conserved and pyrolysis-induced transformation of Prussian Blue Analogue Mn(3)[Co(CN)(6)](2)⋅nH(2)O perfect nanocubes. Owing to the release of CO(2) and N(x)O(y) in the process of interdiffusion, this strategy can overcome to a large extent the disadvantage of the traditional ceramic route for synthesis of spinels, and Mn(x)Co(3-x)O(4) with foamlike porous nanostructure is effectively obtained. Importantly, when evaluated as an electrode material for lithium-ion batteries, the foamlike Mn(x)Co(3-x)O(4) porous nanocubes display high specific discharge capacity and excellent rate capability. The improved electrochemical performance is attributed to the beneficial features of the particular foamlike porous nanostructure and large surface area, which reduce the diffusion length for Li(+) ions and enhance the structural integrity with sufficient void space for buffering the volume variation during the Li(+) insertion/extraction. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Evaporated Lithium Surface Coatings in NSTX

    International Nuclear Information System (INIS)

    Kugel, H.W.; Mansfield, D.; Maingi, Rajesh; Bell, M.G.; Bell, R.E.; Allain, J.P.; Gates, D.; Gerhardt, S.P.; Kaita, R.; Kallman, J.; Kaye, S.; LeBlanc, B.P.; Majeski, R.; Menard, J.; Mueller, D.; Ono, M.; Paul, S.; Raman, R.; Roquemore, A.L.; Ross, P.W.; Sabbagh, S.A.; Schneider, H.; Skinner, C.H.; Soukhanovskii, V.; Stevenson, T.; Timberlake, J.; Wampler, W.R.; Wilgen, John B.; Zakharov, L.E.

    2009-01-01

    Two lithium evaporators were used to evaporate more than 100 g of lithium on to the NSTX lower divertor region. Prior to each discharge, the evaporators were withdrawn behind shutters, where they also remained during the subsequent HeGDC applied for periods up to 9.5 min. After the HeGDC, the shutters were opened and the LITERs were reinserted to deposit lithium on the lower divertor target for 10 min, at rates of 10-70 mg/min, prior to the next discharge. The major improvements in plasma performance from these lithium depositions include: (1) plasma density reduction as a result of lithium deposition; (2) suppression of ELMs; (3) improvement of energy confinement in a low-triangularity shape; (4) improvement in plasma performance for standard, high-triangularity discharges: (5) reduction of the required HeGDC time between discharges; (6) increased pedestal electron and ion temperature; (7) reduced SOL plasma density; and (8) reduced edge neutral density.