WorldWideScience

Sample records for liquids 1-alkyl-3-methylimidazolium bromide

  1. Effect of alkyl chain length and temperature on the thermodynamic properties of ionic liquids 1-alkyl-3-methylimidazolium bromide in aqueous and non-aqueous solutions at different temperatures

    International Nuclear Information System (INIS)

    Sadeghi, Rahmat; Shekaari, Hemayat; Hosseini, Rahim

    2009-01-01

    The alkyl chain length of 1-alkyl-3-methylimidazolium bromide ([Rmim][Br], R = propyl (C 3 ), hexyl (C 6 ), heptyl (C 7 ), and octyl (C 8 )) was varied to prepare a series of room-temperature ionic liquids (RTILs), and experimental measurements of density and speed of sound at different temperatures ranging from (288.15 to 308.15) K for their aqueous and methanolic solutions in the dilute concentration region (0.01 to 0.30) mol . kg -1 were taken. The values of the compressibilities, expansivity and apparent molar properties for [C n mim][Br] in aqueous and methanolic solutions were determined at the investigated temperatures. The obtained apparent molar volumes and apparent molar isentropic compressibilities were fitted to the Redlich-Mayer and the Pitzer's equations from which the corresponding infinite dilution molar properties were obtained. The values of the infinite dilution molar properties were used to obtain some information about solute-solvent and solute-solute interactions. The thermodynamic properties of investigated ionic liquids in aqueous solutions have been compared with those in methanolic solutions. Also, the comparison between thermodynamic properties of investigated solutions and those of electrolyte solutions, polymer solutions, cationic surfactant solutions and tetraalkylammonium salt solutions have been made

  2. Effect of alkyl chain length and temperature on the thermodynamic properties of ionic liquids 1-alkyl-3-methylimidazolium bromide in aqueous and non-aqueous solutions at different temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Sadeghi, Rahmat [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of)], E-mail: rahsadeghi@yahoo.com; Shekaari, Hemayat [Department of Chemistry, Faculty of Science, University of Mohaghegh Ardabili, Ardabil (Iran, Islamic Republic of); Hosseini, Rahim [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of)

    2009-02-15

    The alkyl chain length of 1-alkyl-3-methylimidazolium bromide ([Rmim][Br], R = propyl (C{sub 3}), hexyl (C{sub 6}), heptyl (C{sub 7}), and octyl (C{sub 8})) was varied to prepare a series of room-temperature ionic liquids (RTILs), and experimental measurements of density and speed of sound at different temperatures ranging from (288.15 to 308.15) K for their aqueous and methanolic solutions in the dilute concentration region (0.01 to 0.30) mol . kg{sup -1} were taken. The values of the compressibilities, expansivity and apparent molar properties for [C{sub n}mim][Br] in aqueous and methanolic solutions were determined at the investigated temperatures. The obtained apparent molar volumes and apparent molar isentropic compressibilities were fitted to the Redlich-Mayer and the Pitzer's equations from which the corresponding infinite dilution molar properties were obtained. The values of the infinite dilution molar properties were used to obtain some information about solute-solvent and solute-solute interactions. The thermodynamic properties of investigated ionic liquids in aqueous solutions have been compared with those in methanolic solutions. Also, the comparison between thermodynamic properties of investigated solutions and those of electrolyte solutions, polymer solutions, cationic surfactant solutions and tetraalkylammonium salt solutions have been made.

  3. The acute toxic effects of 1-alkyl-3-methylimidazolium nitrate ionic liquids on Chlorella vulgaris and Daphnia magna.

    Science.gov (United States)

    Zhang, Cheng; Zhang, Shuai; Zhu, Lusheng; Wang, Jinhua; Wang, Jun; Zhou, Tongtong

    2017-10-01

    Given their increasingly widespread application, the toxic effects of ionic liquids (ILs) have become the subject of significant attention in recent years. Therefore, the present study assessed the acute toxic effects of 1-alkyl-3-methylimidazolium nitrate ([C n mim]NO 3 (n = 2, 4, 6, 8, 10, 12)) on Chlorella vulgaris and Daphnia magna. The sensitivity of the tested organism Daphnia magna and the investigated IL concentrations in water using high-performance liquid chromatography (HPLC) were also evaluated to demonstrate the reliability of the present study. The results illustrated that Daphnia magna is indeed sensitive to the reference toxicant and the investigated ILs were stable in the aquatic environment. The 50% effect concentration (EC 50 ) was used to represent the acute toxic effects on Chlorella vulgaris and Daphnia magna. With the increasing alkyl-chain lengths, the toxicity of the investigated ILs increased in both the test organisms. Accordingly, the alkyl-chain lengths can cause significantly toxic effects on aquatic organisms, and Daphnia magna are much more sensitive than Chlorella vulgaris to the imidazolium-based ILs used in the present study. Furthermore, the present study provides more information on the acute toxic effects of 1-alkyl-3-methylimidazolium nitrate. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Isobutane as a probe of the structure of 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ionic liquids

    International Nuclear Information System (INIS)

    Pison, Laure; Bernales, Varinia; Fuentealba, Patricio; Padua, Agilio A.H.

    2015-01-01

    Highlights: • The solubility of isobutane was determined in [C n C 1 Im][NTf 2 ] (n = 2, 4, 6, 8 and 10). • Iso-C 4 H 10 solubility decreases with T and increases with n to reach x = 0.1 (n = 10, T = 303 K). • Isobutane is, on average, 1.6 times less soluble than n-butane in this family of ionic liquids. • Solubility increase with n is due to a more negative enthalpy of dissolution (n ⩾ 6). - Abstract: An experimental study of the solubility and of the thermodynamic properties of solvation, between temperatures (303 and 343) K and at pressures close to atmospheric, of 2-methylpropane (isobutane) in several ionic liquids based on the bis(trifluoromethylsulfonyl)imide anion and on 1-alkyl-3-methylimidazolium cations, [C n C 1 Im][NTf 2 ], with alkyl side-chains varying from two to ten carbon atoms is presented. The isobutane solubility increases with increasing size of the alkyl side-chain of the cation in the ionic liquid and decreases with increasing temperature (as typical of an exothermal dissolution process). The mole fraction solubility of isobutane varies from 0.904 · 10 −2 in [C 2 C 1 Im][NTf 2 ] at T = 343 K to 1.002 · 10 −1 in [C 10 C 1 Im][NTf 2 ] at T = 303 K. The values measured in this work are compared to the behaviour of n-butane in the same ionic liquids published in a previous study (Costa Gomes et al., 2012). Isobutane was found to be significantly less soluble than n-butane in all the ionic liquids. The differences found are interpreted in relation to the molecular structures obtained by molecular dynamics simulations for the solutions of n-butane and isobutane in the studied [C n C 1 Im][NTf 2 ] ionic liquids

  5. Solubility of gases in 1-alkyl-3methylimidazolium alkyl sulfate ionic liquids: Experimental determination and modeling

    International Nuclear Information System (INIS)

    Bermejo, María Dolores; Fieback, Tobias M.; Martín, Ángel

    2013-01-01

    Highlights: ► The solubility of CO 2 , CH 4 and C 2 H 6 in [emim][EtSO 4 ] is measured with a magnetic suspension balance. ► New data and literature results have been modeled with a Group Contribution equation of state. ► A specific group definition is required to model data of ionic liquids with a [MeSO 4 ] anion. ► Deviations between model and experiments are lower than 10% in most cases. ► Deviations of 34% are observed in the case of the solubility of ethane in the ionic liquid. -- Abstract: The solubility of different gases (carbon dioxide, methane, ethane, carbon monoxide and hydrogen) in ionic liquids with an alkyl sulfate anion has been modeled with the Group Contribution equation of state developed by Skjold-Jørgensen. New gas solubility measurements have been carried out with a high pressure magnetic suspension balance in order to cover pressure and temperature ranges not considered in previous studies and to obtain more experimental information for the correlation of parameters of the equation of state. New solubility measurements include the solubility of carbon dioxide in 1-ethyl 3-methyl imidazolium ethyl sulfate [emim][EtSO 4 ] at temperatures of 298 K and 348 K and pressures ranging from 0.3 MPa to 6.5 MPa, the solubility of methane in [emim][EtSO 4 ] at a temperature of 293 K and pressures ranging from 0.2 MPa to 10.2 MPa, and the solubility of ethane in [emim][EtSO 4 ] at temperatures of 323 K and 350 K and pressures ranging from 0.2 MPa to 4 MPa. Results show that the Group Contribution equation of state can be used to describe the solubility of gases in alkyl sulfate ionic liquids as well as infinite dilution coefficients of alkanes in the ionic liquids, with average deviations between experiments and calculations ranging from 1% to 10% in the case of mixtures with CO 2 , CO, CH 4 and H 2 with the alkyl sulfate ionic liquids to up to 34% in the case of the solubility of ethane in [emim][EtSO 4

  6. Buoyancy density measurements for 1-alkyl-3-methylimidazolium based ionic liquids with tetrafluoroborate anion

    Czech Academy of Sciences Publication Activity Database

    Klomfar, Jaroslav; Pátek, Jaroslav; Součková, Monika

    2009-01-01

    Roč. 282, č. 1 (2009), s. 31-37 ISSN 0378-3812 R&D Projects: GA AV ČR IAA200760701 Institutional research plan: CEZ:AV0Z20760514 Keywords : ionic liquid * tetrafluoroborate * density Subject RIV: BJ - Thermodynamics Impact factor: 1.857, year: 2009 http://apps.isiknowledge.com/full_record.do?product=UA&search_mode=GeneralSearch&qid=1&SID=T2B@N@8IL66EeO@FnGf&page=1&doc=2&colname=WOS

  7. Isothermogravimetric determination of the enthalpies of vaporization of 1-alkyl-3-methylimidazolium ionic liquids.

    Science.gov (United States)

    Luo, Huimin; Baker, Gary A; Dai, Sheng

    2008-08-21

    Vaporization enthalpies for two series of ionic liquids (ILs) composed of 1- n-alkyl-3-methylimidazolium cations, [Imm1+] (m=2, 3, 4, 6, 8, or 10), paired with either the bis(trifluoromethanesulfonyl)amide, [Tf2N-], or the bis(perfluoroethylsulfonyl)amide anion, [beti-], were determined using a simple, convenient, and highly reproducible thermogravimetric approach, and from these values, Hildebrand solubility parameters were estimated. Our results reveal two interesting and unanticipated outcomes: (i) methylation at the C2 position of [Imm1+] affords a significantly higher vaporization enthalpy; (ii) in all cases, the [beti-] anion served to lower the enthalpy of vaporization relative to [Tf2N-]. The widespread availability of the apparatus required for these measurements coupled with the ease of automation suggests the broad potential of this methodology for determining this critical parameter in a multitude of ILs.

  8. Ultrasonic Relaxation Study of 1-Alkyl-3-methylimidazolium-Based Room-Temperature Ionic Liquids: Probing the Role of Alkyl Chain Length in the Cation.

    Science.gov (United States)

    Zorębski, Michał; Zorębski, Edward; Dzida, Marzena; Skowronek, Justyna; Jężak, Sylwia; Goodrich, Peter; Jacquemin, Johan

    2016-04-14

    Ultrasound absorption spectra of four 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imides were determined as a function of the alkyl chain length on the cation from 1-propyl to 1-hexyl from 293.15 to 323.15 K at ambient pressure. Herein, the ultrasound absorption measurements were carried out using a standard pulse technique within a frequency range from 10 to 300 MHz. Additionally, the speed of sound, density, and viscosity have been measured. The presence of strong dissipative processes during the ultrasound wave propagation was found experimentally, i.e., relaxation processes in the megahertz range were observed for all compounds over the whole temperature range. The relaxation spectra (both relaxation amplitude and relaxation frequency) were shown to be dependent on the alkyl side chain length of the 1-alkyl-3-methylimidazolium ring. In most cases, a single-Debye model described the absorption spectra very well. However, a comparison of the determined spectra with the spectra of a few other imidazolium-based ionic liquids reported in the literature (in part recalculated in this work) shows that the complexity of the spectra increases rapidly with the elongation of the alkyl chain length on the cation. This complexity indicates that both the volume viscosity and the shear viscosity are involved in relaxation processes even in relatively low frequency ranges. As a consequence, the sound velocity dispersion is present at relatively low megahertz frequencies.

  9. Using ethane and butane as probes to the molecular structure of 1-alkyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl] imide ionic liquids.

    Science.gov (United States)

    Costa Gomes, Margarida F; Pison, Laure; Pensado, Alfonso S; Pádua, Agilio A H

    2012-01-01

    In this work, we have studied the solubility and the thermodynamic properties of solvation, between 298 and 343 K and at pressures close to atmospheric, of ethane and n-butane in several ionic liquids based on the bis[(trifluoromethyl) sulfonyl]imide anion and on 1-alkyl-3-methylimidazolium cations, [CnC1Im] [NTf2], with alkyl side-chains varying from two to ten carbon atoms. The solubility of butane is circa one order of magnitude larger than that of ethane with mole fractions as high as 0.15 in [C10C1Im][NTf2] at 300 K. The solubilities of both n-butane and ethane gases are higher for ionic liquids with longer alkyl chains. The behaviour encountered is explained by the preferential solvation of the gases in the non-polar domains of the solvents, the larger solubility of n-butane being attributed to the dispersive contributions to the interaction energy. The rise in solubility with increasing size of the alkyl-side chain is explained by a more favourable entropy of solvation in the ionic liquids with larger cations. These conclusions are corroborated by molecular dynamics simulation studies.

  10. Determination of the enthalpy of vaporization and prediction of surface tension for ionic liquid 1-alkyl-3-methylimidazolium propionate [C(n)mim][Pro](n = 4, 5, 6).

    Science.gov (United States)

    Tong, Jing; Yang, Hong-Xu; Liu, Ru-Jing; Li, Chi; Xia, Li-Xin; Yang, Jia-Zhen

    2014-11-13

    With the use of isothermogravimetrical analysis, the enthalpies of vaporization, Δ(g)lH(o)m(T(av)), at the average temperature, T(av) = 445.65 K, for the ionic liquids (ILs) 1-alkyl-3-methylimidazolium propionate [C(n)mim][Pro](n = 4, 5, 6) were determined. Using Verevkin's method, the difference of heat capacities between the vapor phase and the liquid phase, Δ(g)lC(p)(o)m, for [C(n)mim][Pro](n = 2, 3, 4, 5, 6), were calculated based on the statistical thermodynamics. Therefore, with the use of Δ(g)lC(p)(o)m, the values of Δ(g)lH(o)m(T(av)) were transformed into Δ(g)lH(o)m(298), 126.8, 130.3, and 136.5 for [C(n)mim][Pro](n = 4, 5, 6), respectively. In terms of the new scale of polarity for ILs, the order of the polarity of [C(n)mim][Pro](n = 2, 3, 4, 5, 6) was predicted, that is, the polarity decreases with increasing methylene. A new model of the relationship between the surface tension and the enthalpy of vaporization for aprotic ILs was put forward and used to predict the surface tension for [C(n)mim][Pro](n = 2, 3, 4, 5, 6) and others. The predicted surface tension for the ILs is in good agreement with the experimental one.

  11. Enhanced CO2 capture in binary mixtures of 1-alkyl-3-methylimidazolium tricyanomethanide ionic liquids with water

    NARCIS (Netherlands)

    Romanos, G.E.; Zubeir, L.F.; Likodimos, V.; Falaras, P.; Kroon, M.C.; Iliev, B.; Adamova, G.; Schubert, T.J.S.

    2013-01-01

    The absorption of carbon dioxide and water in the 1-butyl-3-methylimidazoliun tricyanomethanide ([C4C1im][TCM]) and 1-octyl-3-methylimidazolium tricyanomethanide ([C8C1im][TCM]) ionic liquids (ILs) was systematically investigated for the first time as a function of the H2O content by means of a

  12. Thermal Properties of 1-Alkyl-3-Methylimidazolium bis(trifluoromethylsulfonyl)Imide Ionic Liquids with Linear, Branched and Cyclic Alkyl Substituents.

    Czech Academy of Sciences Publication Activity Database

    Rotrekl, Jan; Storch, Jan; Kloužek, Jaroslav; Vrbka, P.; Husson, P.; Andresová, Adéla; Bendová, Magdalena; Wagner, Zdeněk

    2017-01-01

    Roč. 443, JUL 15 (2017), s. 32-43 ISSN 0378-3812 R&D Projects: GA MŠk LD14090 Institutional support: RVO:67985858 ; RVO:67985891 Keywords : ionic liquids * thermophysical properties * structure-property relationship Subject RIV: CF - Physical ; Theoretical Chemistry; CC - Organic Chemistry (USMH-B) OBOR OECD: Physical chemistry; Organic chemistry (USMH-B) Impact factor: 2.473, year: 2016

  13. P-rho-T Measurements for 1-Alkyl-3-methylimidazolium-Based Ionic Liquids with Tetrafluoroborate and a Trifluoromethanesulfonate, Anion

    Czech Academy of Sciences Publication Activity Database

    Klomfar, Jaroslav; Součková, Monika; Pátek, Jaroslav

    2012-01-01

    Roč. 57, č. 3 (2012), s. 708-720 ISSN 0021-9568 R&D Projects: GA ČR GA101/09/0010; GA AV ČR IAA200760701 Institutional research plan: CEZ:AV0Z20760514 Keywords : ionic liquids * tetrafluoroborate * trifluoromethanesulfonate * density Subject RIV: BJ - Thermodynamics Impact factor: 2.004, year: 2012 http://pubs.acs.org/doi/abs/10.1021/je200903m

  14. Enhanced CO2 capture in binary mixtures of 1-alkyl-3-methylimidazolium tricyanomethanide ionic liquids with water.

    Science.gov (United States)

    Romanos, George E; Zubeir, Lawien F; Likodimos, Vlassis; Falaras, Polycarpos; Kroon, Maaike C; Iliev, Boyan; Adamova, Gabriela; Schubert, Thomas J S

    2013-10-10

    Absorption of carbon dioxide and water in 1-butyl-3-methylimidazoliun tricyanomethanide ([C4C1im][TCM]) and 1-octyl-3-methylimidazolium tricyanomethanide ([C8C1im][TCM]) ionic liquids (ILs) was systematically investigated for the first time as a function of the H2O content by means of a gravimetric system together with in-situ Raman spectroscopy, excess molar volume (V(E)), and viscosity deviation measurements. Although CO2 absorption was marginally affected by water at low H2O molar fractions for both ILs, an increase of the H2O content resulted in a marked enhancement of both the CO2 solubility (ca. 4-fold) and diffusivity (ca. 10-fold) in the binary [C(n)C1im][TCM]/H2O systems, in contrast to the weak and/or detrimental influence of water in most physically and chemically CO2-absorbing ILs. In-situ Raman spectroscopy on the IL/CO2 systems verified that CO2 is physically absorbed in the dry ILs with no significant effect on their structural organization. A pronounced variation of distinct tricyanomethanide Raman modes was disclosed in the [C(n)C1im][TCM]/H2O mixtures, attesting to the gradual disruption of the anion-cation coupling by the hydrogen-bonded water molecules to the [TCM](-) anions, in accordance with the positive excess molar volumes and negative viscosity deviations for the binary systems. Most importantly, CO2 absorption in the ILs/H2O mixtures at high water concentrations revealed that the [TCM](-) Raman modes tend to restore their original state for the heavily hydrated ILs, in qualitative agreement with the intriguing nonmonotonous transients of CO2 absorption kinetics unveiled by the gravimetric measurements for the hybrid solvents. A molecular exchange mechanism between CO2 in the gas phase and H2O in the liquid phase was thereby proposed to explain the enhanced CO2 absorption in the hybrid [C(n)C1im][TCM]//H2O solvents based on the subtle competition between the TCM-H2O and TCM-CO2 interactions, which renders these ILs very promising for CO2

  15. Odd-even effect on the formation of aqueous biphasic systems formed by 1-alkyl-3-methylimidazolium chloride ionic liquids and salts

    Science.gov (United States)

    Belchior, Diana C. V.; Sintra, Tânia E.; Carvalho, Pedro J.; Soromenho, Mário R. C.; Esperança, José M. S. S.; Ventura, Sónia P. M.; Rogers, Robin D.; Coutinho, João A. P.; Freire, Mara G.

    2018-05-01

    This work provides a comprehensive evaluation of the effect of the cation alkyl side chain length of the 1-alkyl-3-methylimidazolium chloride series ([CnC1im]Cl, n = 2-14) of ionic liquids (ILs) on their capability to form aqueous biphasic systems (ABSs) with salts and self-aggregation derived properties. The liquid-liquid phase behavior of ternary systems composed of [CnC1im]Cl, water, and K3PO4 or K2CO3 and the respective Setschenow salting-out coefficients (ks), a quantitative measure of the two-phase formation ability, were determined. An odd-even effect in the ks values along the number of methylene groups of the longest IL cation alkyl side chain was identified for the ABS formed by K2CO3, a weaker salting-out agent where the phenomenon is clearly identified. In general, cations with even alkyl side chains, being likely to display higher molar volumes, are more easily salted-out and thus more prone to undergo phase separation. The odd-even effect in the ks values is, however, more significant in ILs up to n = 6, where the nanostructuration/nanosegregation of ILs plays a less relevant role. Still, with the [CnC1im]Cl (n = 7-14) series of ILs, an odd-even effect was also identified in the ILs' ionization degree, molar conductivity, and conductivity at infinite dilution. In summary, it is shown here that the ILs' odd-even effect occurs in IL aqueous solutions and not just in neat ILs, an already well-established phenomenon occurring in a series of ILs' properties described as a result of the orientation of the terminal methyl groups to the imidazolium ring cation and consequent effect in the ILs' cohesive energy.

  16. The microwave assisted synthesis of 1-alkyl-3-methylimidazolium bromide as potential corrosion inhibitor toward carbon steel in 1 M HCl solution saturated with carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Pasasa, Norman Vincent A., E-mail: npasasa@gmail.com; Bundjali, Bunbun; Wahyuningrum, Deana [Department of Chemistry, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Jalan Ganesha No. 10 Bandung, Jawa Barat (Indonesia)

    2015-09-30

    Injection of corrosion inhibitor into the fluid current of oil and gas pipelines is an effective way to mitigate corrosion rate on the inner-surface parts of pipelines, especially carbon steel pipelines. In this research, two alkylimidazolium ionic liquids, 1-decyl-3-methylimidazolium bromide (IL1) and 1-dodecyl-3-methylimidazolium bromide (IL2) have been synthesized and studied as a potential corrosion inhibitor towards carbon steel in 1 M HCl solution saturated with carbon dioxide. IL1 and IL2 were synthesized using microwave assisted organic synthesis (MAOS) method. Mass Spectrometry analysis of IL1 and IL2 showed molecular mass [M-H+] peak at 223.2166 and 251.2484, respectively. The FTIR,{sup 1}H-NMR and {sup 13}C-NMR spectra confirmed that IL1 and IL2 were successfully synthesized. Corrosion inhibition activity of IL1 and IL2 were determined using weight loss method. The results showed that IL1 and IL2 have the potential as good corrosion inhibitors with corrosion inhibition efficiency of IL1 and IL2 are 96.00% at 100 ppm (343 K) and 95.60% at 50 ppm (343 K), respectively. The increase in the concentration of IL1 and IL2 tends to improve their corrosion inhibition activities. Analysis of the data obtained from the weight loss method shows that the adsorption of IL1 and IL2 on carbon steel is classified into chemisorption which obeys Langmuir’s adsorption isotherm.

  17. Prediction of the thermodynamic properties of 1-alkyl-3-methylimidazolium lactate ionic liquids [C_nmim][Lact](n=2,3,4,5,and 6) by parachor

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    An ionic liquid (IL) based on lactate,1-butyl-3-methylimidazolium lactate ([C4mim][Lact]),has been prepared and characterized by 1H nuclear magnetic resonance (NMR) spectroscopy and differential scanning calorimetry (DSC).Since the IL can form strong hydrogen bonds with water,trace water is a problematic impurity in the IL.Using the standard addition method (SAM),the density,refractive index and surface tension of [C4mim][Lact] were measured in the temperature range (308.15 to 343.15 ± 0.05) K.On the basis of the experimental data,the parachor and molar volume for [C4mim][Lact],and the molecular volume V m,surface tension γ,molar enthalpy of vaporization △lgHm 0,refractive index n D,and the thermal expansion coefficients,for the homologues [Cnmim][Lact] (n=2,3,4,5,and 6) were estimated using semi-empirical methods.The estimated values are in good agreement with the experimental data.

  18. Studies on properties of ionic liquids 1-alkyl-3-methylimidazolium lactate at temperatures from (288.15 to 333.15) K

    International Nuclear Information System (INIS)

    Hong, Mei; Sun, Ao; Yang, Qi; Guan, Wei; Tong, Jing; Yang, Jia-Zhen

    2013-01-01

    Highlights: • Two ILs [C 2 mim][Lact] and [C 5 mim][Lact] were prepared. • The density, surface tension and refractive index for two ILs were measured in terms of SAT. • Using Kabo’s and Rebelo’s method, the molar enthalpy of evaporation for two ILs was estimated. • The surface tension was estimated using the parachor and the refractive index. -- Abstract: Two chiral ionic liquids based on lactic acid (LAILs), 1-ethyl-3-methylimidazolium lactate ([C 2 mim][Lact]) and 1-pentyl-3-methylimidazolium lactate ([C 5 mim][Lact]), have been prepared by the neutralization method and characterized by 1 H NMR and DSC. Their density, surface tension and refractive index were measured at T {(288.15 to 333.15) ± 0.05} K. Since the LAILs can form strong hydrogen bonds with water, small amounts of water are difficult to remove by conventional methods. In order to eliminate the effect of the impurity as water, the standard addition method (SAM) was applied to these measurements. The molar volume of [C n mim][Lact] (n = 2, 5), the thermal expansion coefficient, α, the surface excess entropy, S a , the surface excess energy E a , parachor, P, and molar refraction, R m , were obtained. According to the methods of both Kabo and Rebelo, the molar enthalpy of evapouration of the LAILs was estimated using experimental values for the surface tension and molar volume. At the same time, the surface tension of the LAILs may be estimated using the data of the parachor and refractive index. The estimated values of the surface tension correlate quite well with the corresponding experimental values

  19. Implementation of perturbed-chain statistical associating fluid theory (PC-SAFT), generalized (G)SAFT+cubic, and cubic-plus-association (CPA) for modeling thermophysical properties of selected 1-alkyl-3-methylimidazolium ionic liquids in a wide pressure range.

    Science.gov (United States)

    Polishuk, Ilya

    2013-03-14

    This study is the first comparative investigation of predicting the isochoric and the isobaric heat capacities, the isothermal and the isentropic compressibilities, the isobaric thermal expansibilities, the thermal pressure coefficients, and the sound velocities of ionic liquids by statistical associating fluid theory (SAFT) equation of state (EoS) models and cubic-plus-association (CPA). It is demonstrated that, taking into account the high uncertainty of the literature data (excluding sound velocities), the generalized for heavy compounds version of SAFT+Cubic (GSAFT+Cubic) appears as a robust estimator of the auxiliary thermodynamic properties under consideration. In the case of the ionic liquids the performance of PC-SAFT seems to be less accurate in comparison to ordinary compounds. In particular, PC-SAFT substantially overestimates heat capacities and underestimates the temperature and pressure dependencies of sound velocities and compressibilities. An undesired phenomenon of predicting high fictitious critical temperatures of ionic liquids by PC-SAFT should be noticed as well. CPA is the less accurate estimator of the liquid phase properties, but it is advantageous in modeling vapor pressures and vaporization enthalpies of ionic liquids. At the same time, the preliminary results indicate that the inaccuracies in predicting the deep vacuum vapor pressures of ionic liquids do not influence modeling of phase equilibria in their mixtures at much higher pressures.

  20. Effects of 1-Alkyl-3-Methylimidazolium Nitrate on Soil Physical and Chemical Properties and Microbial Biomass.

    Science.gov (United States)

    Zhou, Tongtong; Wang, Jun; Ma, Zhiqiang; Du, Zhongkun; Zhang, Cheng; Zhu, Lusheng; Wang, Jinhua

    2018-05-01

    Ionic liquids (ILs), also called room temperature ILs, are widely applied in many fields on the basis of their unique physical and chemical properties. However, numerous ILs may be released into and gradually accumulate in the environment due to their extensive use and absolute solubility. The effects of 1-alkyl-3-methylimidazolium nitrate ([C n mim]NO 3 , n = 4, 6, 8) on soil pH, conductivity, cation exchange capacity, microbial biomass carbon, and microbial biomass nitrogen were examined at the doses of 1, 10, and 100 mg/kg on days 10, 20, 30, and 40. The results demonstrated that the soil pH decreased and the conductivity increased with increasing IL doses. No significant differences were observed in the soil cation-exchange capacity. All three of the tested ILs decreased the soil microbial biomass carbon and nitrogen. Additionally, there were few differences among the ILs with different alkyl chain lengths on the tested indicators except for the microbial biomass nitrogen. The present study addressed a gap in the literature regarding the effects of the aforementioned ILs with different alkyl side chains on the physicochemical properties of soil, and the results could provide the basic data for future studies on their toxicity to soil organisms, such as earthworms and soil microbes.

  1. Estimation of physicochemical properties of 1-alkyl-3-methylimidazolium glutamate

    International Nuclear Information System (INIS)

    Fang, Da-wei; Yan, Qiang; Li, Du; Xia, Li-Xin; Zang, Shu-Liang

    2014-01-01

    Highlights: • The standard addition method (SAM) was applied in determination of density and surface tension of amino acid ionic liquids. • The molar refraction has been calculated by experimental data of refractive index. • Physico-chemical properties of the homologue of [C n mim][Glu] have been predicted by semiempirical methods. - Abstract: Amino acid ionic liquids (AAILs) [C 5 mim][Glu] (1-pentyl-3-methylimidazolium glutamate) and [C 6 mim][Glu] (1-hexyl-3-methylimidazolium glutamate) were prepared by the neutralization method and characterized by 1 H NMR spectroscopy and DSC. The values of their density, surface tension were measured over the temperature range (308.15 to 343.15 ± 0.05) K, and the refractive index was measured within the temperature range (293.15 to 328.15 ± 0.05) K. Since the AAILs can form strong hydrogen bonds with water, a small amount of water is difficult to remove from the AAILs by common methods. In order to eliminate the effect of water as an impurity existed in AAIL sample, the standard addition method (SAM) was applied to these measurements. In terms of a semi-empirical method, the following physico-chemical properties were predicted: molecular volume, V m , standard molar entropy, S 0 , parachor, P, surface tension, γ, thermal expansion coefficients, α, molar refraction, R M , and refractive index, n D , of the homologue of [C n mim][Glu] (n = 2, 3, 4)

  2. Structure, conformations, vibrations, and ideal-gas properties of 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ionic pairs and constituent ions.

    Science.gov (United States)

    Paulechka, Yauheni U; Kabo, Gennady J; Emel'yanenko, Vladimir N

    2008-12-11

    Energies, geometries, and frequencies of normal vibrations have been calculated by quantum-chemical methods for different conformers of a bis(trifluoromethylsulfonyl)imide anion (NTf2-), 1-alkyl-3-methylimidazolium cations ([C(n)mim]+, n = 2, 4, 6, 8), and [C(n)mim]NTf2 ionic pairs. The assignment of frequencies for NTf2-, [C2mim]+, and [C4mim]+ in the vibrational spectra of ionic liquids have been performed. Thermodynamic properties of [C(n)mim]NTf2, [C(n)mim]+, and NTf2- in the gas state have been calculated by the statistical thermodynamic methods. The resulting entropies are in satisfactory agreement with the values obtained from the experimental data previously reported in literature.

  3. Effect of alkyl chain length on the rotational diffusion of nonpolar and ionic solutes in 1-alkyl-3-methylimidazolium-bis(trifluoromethylsulfonyl)imides.

    Science.gov (United States)

    Gangamallaiah, V; Dutt, G B

    2013-10-10

    Rotational diffusion of a nonpolar solute 9-phenylanthracene (9-PA) and a cationic solute rhodamine 110 (R110) has been examined in a series of 1-alkyl-3-methylimidazolium (alkyl = octyl, decyl, dodecyl, tetradecyl, hexadecyl, and octadecyl) bis(trifluoromethylsulfonyl)imides to understand the influence of alkyl chain length on solute rotation. In this study, reorientation times (τr) have been measured as a function of viscosity (η) by varying the temperature (T) of the solvents. These results have been analyzed using the Stokes-Einstein-Debye (SED) hydrodynamic theory along with the ones obtained for the same solutes in 1-alkyl-3-methylimidazolium (alkyl = methyl, ethyl, propyl, butyl, and hexyl) bis(trifluoromethylsulfonyl)imides (Gangamallaiah and Dutt, J. Phys. Chem. B 2012, 116, 12819-12825). It has been noticed that the data for 9-PA and R110 follows the relation τr = A(η/T)(n) with A being the ratio of hydrodynamic volume of the solute to the Boltzmann constant and n = 1 as envisaged by the SED theory. However, upon increasing the alkyl chain length from methyl to octadecyl significant deviations from the SED theory have been observed especially from the octyl derivative onward. From methyl to octadecyl derivatives, the value of A decreases by a factor of 3 for both the solutes and n by a factor of 1.4 and 1.6 for 9-PA and R110, respectively. These observations have been rationalized by taking into consideration the organized structure of the ionic liquids, whose influence appears to be pronounced when the number of carbon atoms in the alkyl chain attached to the imidazolium cation exceeds eight.

  4. Rotational diffusion of nonpolar and ionic solutes in 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imides: is solute rotation always influenced by the length of the alkyl chain on the imidazolium cation?

    Science.gov (United States)

    Gangamallaiah, V; Dutt, G B

    2012-10-25

    In an attempt to find out whether the length of the alkyl chain on the imidazolium cation has a bearing on solute rotation, temperature-dependent fluorescence anisotropies of three structurally similar solutes have been measured in a series of 1-alkyl-3-methylimidazolium (alkyl = methyl, ethyl, propyl, butyl, and hexyl) bis(trifluoromethylsulfonyl)imides. Solute-solvent coupling constants obtained from the experimentally measured reorientation times with the aid of Stokes-Einstein-Debye hydrodynamic theory indicate that there is no influence of the length of the alkyl chain on the rotation of nonpolar, anionic, and cationic solutes 9-phenylanthracene (9-PA), fluorescein (FL), and rhodamine 110 (R110), respectively. It has also been noticed that the rotational diffusion of 9-PA is closer to the predictions of slip hydrodynamics, whereas the rotation of negatively charged FL and positively charged R110 is almost identical and follows stick hydrodynamics in these ionic liquids. Despite having similar shape and size, ionic solutes rotate slower by a factor of 3-4 compared to the nonpolar solute. Interplay of specific and electrostatic interactions between FL and the imidazolium cation of the ionic liquids, and between R110 and the bis(trifluoromethylsulfonyl)imide anion, appear to be responsible for the observed behavior. These results are an indication that the length of the alkyl chain on the imidazolium cation does not alter their physical properties in a manner that has an effect on solute rotation.

  5. Extraction and Chromatographic Determination of Shikimic Acid in Chinese Conifer Needles with 1-Benzyl-3-methylimidazolium Bromide Ionic Liquid Aqueous Solutions

    Science.gov (United States)

    Chen, Fengli; Hou, Kexin; Li, Shuangyang; Zu, Yuangang; Yang, Lei

    2014-01-01

    An ionic liquids-based ultrasound-assisted extraction (ILUAE) method was successfully developed for extracting shikimic acid from conifer needles. Eleven 1-alkyl-3-methylimidazolium ionic liquids with different cations and anions were investigated and 1-benzyl-3-methylimidazolium bromide solution was selected as the solvent. The conditions for ILUAE, including the ionic liquid concentration, ultrasound power, ultrasound time, and liquid-solid ratio, were optimized. The proposed method had good recovery (99.37%–100.11%) and reproducibility (RSD, n = 6; 3.6%). ILUAE was an efficient, rapid, and simple sample preparation technique that showed high reproducibility. Based on the results, a number of plant species, namely, Picea koraiensis, Picea meyeri, Pinus elliottii, and Pinus banksiana, were identified as among the best resources of shikimic acid. PMID:24782942

  6. Temperature Dependence Measurements of the Density at 0.1 MPa for 1-Alkyl-3-methylimidazolium-Based Ionic Liquids with the Trifluoromethanesulfonate and Tetrafluoroborate Anion

    Czech Academy of Sciences Publication Activity Database

    Klomfar, Jaroslav; Součková, Monika; Pátek, Jaroslav

    2010-01-01

    Roč. 55, č. 9 (2010), s. 4054-4057 ISSN 0021-9568 R&D Projects: GA AV ČR IAA200760701 Institutional research plan: CEZ:AV0Z20760514 Keywords : density * tetrafluoroborate * trifluoromethanesulfonate Subject RIV: BJ - Thermodynamics Impact factor: 2.089, year: 2010 http://pubs.acs.org/doi/pdfplus/10.1021/je100185e

  7. Carbohydrates-tailored phase tunable systems composed of ionic liquids and water

    International Nuclear Information System (INIS)

    Chen Yuhaun; Wang Yige; Cheng Qingyan; Liu Xiaoli; Zhang Suojiang

    2009-01-01

    Carbohydrates were found to have substantial effects on tailoring phase tunable of ionic liquids (ILs) and water. Phase behaviors of 1-alkyl-3-methylimidazolium derivatives [C n mim]X (n = 2 to 10, X = Cl - , Br - , BF 4 - )-carbohydrate-H 2 O were systemically investigated. For hydrophilic ILs, 1-alkyl-3-methylimidazolium tetrafluoroborate [C n mim]BF 4 (n = 3, 4), the homogeneous aqueous solution can be induced to separate two aqueous phases by addition of carbohydrate. For hydrophobic ILs, [C n mim]BF 4 (n = 5 to 10), the mutual solubility with water can be lowered by addition of carbohydrate. While 1-alkyl-3-methyl imidazolium chloride ([C n mim]Cl, n = 2 to 10) and 1-alkyl-3-methyl imidazolium bromide ([C n mim]Br, n = 2 to 10) aqueous solutions never form aqueous two-phase systems (ATPSs) with carbohydrate in the investigated temperatures ranging from (242.15 to 373.15) K. The high partitioning behavior of phenol in [C n mim]BF 4 (n = 3 to 10) (1) + carbohydrate (2) + H 2 O (3) shows that carbohydrate-tailored {IL + H 2 O} systems are feasible to be used as extraction systems, especially in biological and environmental engineering.

  8. IONIC LIQUID-CATALYZED ALKYLATION OF ISOBUTANE WITH 2-BUTENE

    Science.gov (United States)

    A detailed study of the alkylation of isobutane with 2-butene in ionic liquid media has been conducted using 1-alkyl-3-methylimidazolium halides?aluminum chloride encompassing various alkyl groups (butyl-, hexyl-, and octyl-) and halides (Cl, Br, and I) on its cations and anions,...

  9. Ionic liquids: differential scanning calorimetry as a new indirect method for determination of vaporization enthalpies.

    Science.gov (United States)

    Verevkin, Sergey P; Emel'yanenko, Vladimir N; Zaitsau, Dzmitry H; Ralys, Ricardas V; Schick, Christoph

    2012-04-12

    Differential scanning calorimetry (DSC) has been used to measure enthalpies of synthesis reactions of the 1-alkyl-3-methylimidazolium bromide [C(n)mim][Br] ionic liquids from 1-methylimidazole and n-alkyl bromides (with n = 4, 5, 6, 7, and 8). The optimal experimental conditions have been elaborated. Enthalpies of formation of these ionic liquids in the liquid state have been determined using the DSC results according to the Hess Law. The ideal-gas enthalpies of formation of [C(n)mim][Br] were calculated using the methods of quantum chemistry. They were used together with the DSC results to derive indirectly the enthalpies of vaporization of the ionic liquids under study. In order to validate the indirect determination, the experimental vaporization enthalpy of [C(4)mim][Br] was measured by using a quartz crystal microbalance (QCM). The combination of reaction enthalpy measurements by DSC with modern high-level first-principles calculations opens valuable indirect thermochemical options to obtain values of vaporization enthalpies of ionic liquids.

  10. Charge Transport and Phase Behavior of Imidazolium-Based Ionic Liquid Crystals from Fully Atomistic Simulations.

    Science.gov (United States)

    Quevillon, Michael J; Whitmer, Jonathan K

    2018-01-02

    Ionic liquid crystals occupy an intriguing middle ground between room-temperature ionic liquids and mesostructured liquid crystals. Here, we examine a non-polarizable, fully atomistic model of the 1-alkyl-3-methylimidazolium nitrate family using molecular dynamics in the constant pressure-constant temperature ensemble. These materials exhibit a distinct "smectic" liquid phase, characterized by layers formed by the molecules, which separate the ionic and aliphatic moieties. In particular, we discuss the implications this layering may have for electrolyte applications.

  11. Imidazolium ionic liquids as solvents for cerium(IV)-mediated oxidation reactions

    OpenAIRE

    Mehdi, Hasan; Bodor, Andrea; Lantos, Diana; Horváth, István T; De Vos, Dirk; Binnemans, Koen

    2007-01-01

    Use of imidazolium ionic liquids as solvents for organic transformations with tetravalent cerium salts as oxidizing agents was evaluated. Good solubility was found for ammonium hexanitratocerate(IV) (ceric ammonium nitrate, CAN) and cerium(IV) triflate in 1-alkyl-3-methylimidazolium triflate ionic liquids. Oxidation of benzyl alcohol to benzaldehyde in 1-ethyl-3-methylimidazolium triflate was studied by in-situ FTIR spectroscopy and 13C NMR spectroscopy on carbon-13-labeled benzyl alcohol. Ca...

  12. Identification of degradation products of ionic liquids in an ultrasound assisted zero-valent iron activated carbon micro-electrolysis system and their degradation mechanism.

    Science.gov (United States)

    Zhou, Haimei; Lv, Ping; Shen, Yuanyuan; Wang, Jianji; Fan, Jing

    2013-06-15

    Ionic liquids (ILs) have potential applications in many areas of chemical industry because of their unique properties. However, it has been shown that the ILs commonly used to date are toxic and not biodegradable in nature, thus development of efficient chemical methods for the degradation of ILs is imperative. In this work, degradation of imidazolium, piperidinium, pyrrolidinium and morpholinium based ILs in an ultrasound and zero-valent iron activated carbon (ZVI/AC) micro-electrolysis system was investigated, and some intermediates generated during the degradation were identified. It was found that more than 90% of 1-alkyl-3-methylimidazolium bromide ([Cnmim]Br, n = 2, 4, 6, 8, 10) could be degraded within 110 min, and three intermediates 1-alkyl-3-methyl-2,4,5-trioxoimidazolidine, 1-alkyl-3-methylurea and N-alkylformamide were detected. On the other hand, 1-butyl-1-methylpiperidinium bromide ([C4mpip]Br), 1-butyl-1-methylpyrrolidinium bromide ([C4mpyr]Br) and N-butyl-N-methylmorpholinium bromide ([C4mmor]Br) were also effectively degraded through the sequential oxidization into hydroxyl, carbonyl and carboxyl groups in different positions of the butyl side chain, and then the N-butyl side chain was broken to form the final products of N-methylpiperidinium, N-methylpyrrolidinium and N-methylmorpholinium, respectively. Based on these intermediate products, degradation pathways of these ILs were suggested. These findings may provide fundamental information on the assessment of the factors related to the environmental fate and environmental behavior of these commonly used ILs. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Synthesis, Characterization, and Impregnation of Some Ionic Liquids on Polymer Membrane for Separation of Carbon Dioxide from Its Mixture with Methane

    Directory of Open Access Journals (Sweden)

    T. T. L. Bui

    2018-03-01

    Full Text Available Some 1-alkyl-3-methylimidazolium-based ionic liquids were synthesized, characterized, and immobilized on membranes to form supported ionic liquid membranes. The supported ionic liquid membranes were characterized by SEM. The initial transmembrane pressures were investigated for each type of impregnated membrane. The CO2/CH4 single gas and mixed gas permeability (CO2 and CH4 have been investigated. The results showed that the CO2/CH4 ideal selectivities and mixed gas selectivities reached 15.45 – 23.9 and 13.91 – 22.82, respectively (equivalent to separation yields of 93.3 – 95.98 %.mThe 1-alkyl-3-methylimidazolium acetate impregnated membrane leads to a slightly lowermCO2/CH4 selectivity, however, this ionic liquid is stable, free of halogen and has a low price. The impregnated membranes prepared from polyvinylidene fluoride are more stablemthan those from polyethersulfone support, and have a higher affinity for CO2 compared to other gas. The obtained high CO2/CH4 selectivities indicate that immobilized membranes can be used for CO2 separation processes.

  14. The physicochemical properties of the low-temperature ionic liquid silver bromide-1-butyl-3-methylimidazolium bromide

    Science.gov (United States)

    Grishina, E. P.; Ramenskaya, L. M.; Pimenova, A. M.

    2009-11-01

    The physicochemical properties of the low-temperature ionic liquid based on 1-butyl-3-methylimidazolium bromide (BMImBr) and silver bromide were studied. Differential scanning calorimetry, Fourier transform IR spectroscopy, densimetry, viscometry, and conductometry measurements were performed to determine the dependences of the parameters under study on the concentration of AgBr. It was shown that the temperature and concentration behavior of the physicochemical properties of BMImBr-AgBr melts characterized the interaction between the system components with the formation of complex particles.

  15. Surface tension and 0.1 MPa density of 1-alkyl-3-methylimidazolium tetrafluoroborates in a homologous series perspective

    Czech Academy of Sciences Publication Activity Database

    Součková, Monika; Klomfar, Jaroslav; Pátek, Jaroslav

    2016-01-01

    Roč. 100, September (2016), s. 79-88 ISSN 0021-9614 R&D Projects: GA ČR GA13-00145S Institutional support: RVO:61388998 Keywords : 1-Cn-3-methylimidazolium cation * tetrafluoroborate anion * density–temperature relation * surface tension–temperature relation * recommended property values Subject RIV: BJ - Thermodynamics Impact factor: 2.726, year: 2016

  16. Calculating the enthalpy of vaporization for ionic liquid clusters.

    Science.gov (United States)

    Kelkar, Manish S; Maginn, Edward J

    2007-08-16

    Classical atomistic simulations are used to compute the enthalpy of vaporization of a series of ionic liquids composed of 1-alkyl-3-methylimidazolium cations paired with the bis(trifluoromethylsulfonyl)imide anion. The calculations show that the enthalpy of vaporization is lowest for neutral ion pairs. The enthalpy of vaporization increases by about 40 kJ/mol with the addition of each ion pair to the vaporizing cluster. Non-neutral clusters have much higher vaporization enthalpies than their neutral counterparts and thus are not expected to make up a significant fraction of volatile species. The enthalpy of vaporization increases slightly as the cation alkyl chain length increases and as temperature decreases. The calculated vaporization enthalpies are consistent with two sets of recent experimental measurements as well as with previous atomistic simulations.

  17. Thermodynamics of dilute aqueous solutions of imidazolium based ionic liquids

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Tejwant [Salt and Marine Chemicals Division, Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research (CSIR), G.B. Marg, Bhavnagar 364002 (India); Kumar, Arvind, E-mail: arvind@csmcri.or [Salt and Marine Chemicals Division, Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research (CSIR), G.B. Marg, Bhavnagar 364002 (India)

    2011-06-15

    Research highlights: The thermodynamic behaviour of aqueous imidazolium ILs has been investigated. Volumetric and ultrasonic results indicated the hydrophobic hydration of ILs. Viscometric studies revealed studied ionic liquids as water-structure makers. Hydration number increased with increase in alkyl chain length of the cation. - Abstract: Experimental measurements of density {rho}, speed of sound u, and viscosity {eta} of aqueous solutions of various 1-alkyl-3-methylimidazolium based ionic liquid (IL) solutions have been performed in dilute concentration regime at 298.15 K to get insight into hydration behaviour of ILs. The investigated ILs are based on 1-alkyl-3-methylimidazolium cation, [C{sub n}mim] having [BF{sub 4}]{sup -}, [Cl]{sup -}, [C{sub 1}OSO{sub 3}]{sup -}, and [C{sub 8}OSO{sub 3}]{sup -} as anions where n = 4 or 8. Several thermodynamic parameters like apparent molar volume {phi}{sub V}, isentropic compressibility {beta}{sub s}, and viscosity B-coefficients have been derived from experimental data. Limiting value of apparent molar volume has been discussed in terms of intrinsic molar volume (V{sub int}) molar electrostriction volume (V{sub elec}), molar disordered (V{sub dis}), and cage volume (V{sub cage}). Viscosity B-coefficients have been used to quantify the kosmotropic or chaotropic nature of ILs. Hydration number of ILs obtained using elctrostriction volume, isentropic compressibility, viscosity, and differential scanning calorimetry have been found to be comparative within the experimental error. The hydrophobic hydration has found to play an important role in hydration of ILs as compared to hydration due to hydrogen bonding and electrostriction. Limiting molar properties, hydration numbers, and B-coefficients have been discussed in terms of alkyl chain length of cation or nature of anion.

  18. Thermodynamics of dilute aqueous solutions of imidazolium based ionic liquids

    International Nuclear Information System (INIS)

    Singh, Tejwant; Kumar, Arvind

    2011-01-01

    Research highlights: → The thermodynamic behaviour of aqueous imidazolium ILs has been investigated. → Volumetric and ultrasonic results indicated the hydrophobic hydration of ILs. → Viscometric studies revealed studied ionic liquids as water-structure makers. → Hydration number increased with increase in alkyl chain length of the cation. - Abstract: Experimental measurements of density ρ, speed of sound u, and viscosity η of aqueous solutions of various 1-alkyl-3-methylimidazolium based ionic liquid (IL) solutions have been performed in dilute concentration regime at 298.15 K to get insight into hydration behaviour of ILs. The investigated ILs are based on 1-alkyl-3-methylimidazolium cation, [C n mim] having [BF 4 ] - , [Cl] - , [C 1 OSO 3 ] - , and [C 8 OSO 3 ] - as anions where n = 4 or 8. Several thermodynamic parameters like apparent molar volume φ V , isentropic compressibility β s , and viscosity B-coefficients have been derived from experimental data. Limiting value of apparent molar volume has been discussed in terms of intrinsic molar volume (V int ) molar electrostriction volume (V elec ), molar disordered (V dis ), and cage volume (V cage ). Viscosity B-coefficients have been used to quantify the kosmotropic or chaotropic nature of ILs. Hydration number of ILs obtained using elctrostriction volume, isentropic compressibility, viscosity, and differential scanning calorimetry have been found to be comparative within the experimental error. The hydrophobic hydration has found to play an important role in hydration of ILs as compared to hydration due to hydrogen bonding and electrostriction. Limiting molar properties, hydration numbers, and B-coefficients have been discussed in terms of alkyl chain length of cation or nature of anion.

  19. Measurement and correlation of vapor-liquid equilibria for a binary system containing 1-butyl-3-methylimidazolium tridecafluorohexyl sulfonate and carbon dioxide

    International Nuclear Information System (INIS)

    Hong, Soon Kang; Park, Yoon Kook

    2016-01-01

    Using a high-pressure variable-volume view cell, the vapor-liquid equilibria of the binary system CO 2 and 1-butyl-3-methylimidazolium tridecafluorohexylsulfonate ([BMIM][TDfO]) were determined. The CO 2 mole fraction ranged from 0.104 to 0.952 over a temperature range of 298.2-323.2 K. Both the Peng-Robinson and Soave-Redlich- Kwong equations of state were applied with two different mixing rules to correlate with the experimentally obtained results. Increasing the alkyl chain length in perfluorinated sulfonate anion mother structure from methyl to hexyl markedly increased the CO 2 solubility. To investigate the effect of the number of fluorine atoms in the anion on the phase behavior of imidazolium-based ionic liquid, these experimental results were then compared with those reported in previous experimental studies of 1-alkyl-3-methylimidazolium cations-including ionic liquid+CO 2 binary system.

  20. Capacitance evolution of electrochemical capacitors with tailored nanoporous electrodes in pure and dissolved ionic liquids

    Energy Technology Data Exchange (ETDEWEB)

    Mysyk, R.; Raymundo-Pinero, E. [CRMD, CNRS/University, Orleans (France); Ruiz, V.; Santamaria, R. [Instituto Nacional del Carbon (CSIC), Oviedo (Spain); Beguin, F.

    2010-10-15

    A homologous series of ionic liquids (IL) with 1-alkyl-3-methylimidazolium cations of different lengths of alkyl chain was used to study the effect of cation size on the capacitive response of two carbons with a tailored pore size distribution. The results reveal a clear ion-sieving effect in pure ILs, while the effect is heavily mitigated for the same salts used in solution, most likely due to somewhat stronger geometrical flexibility of dissolved ions. For the electrode material showing the ion-sieving effect in solution, the gravimetric capacitance values are higher than in pure ILs. The dissimilarity of capacitance values between pure and dissolved ILs with ion-sieving carbons highlights their respective advantages and disadvantages in terms of energy density: whereas pure ILs can potentially provide a larger working voltage window, the corresponding dissolved salts can access smaller pores, mostly contributing to higher capacitance values. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  1. Interaction mechanisms of ionic liquids [Cnmim]Br (n=4, 6, 8, 10) with bovine serum albumin

    International Nuclear Information System (INIS)

    Yan Hua; Wu Junyong; Dai Guoliang; Zhong Aiguo; Chen Hao; Yang Jianguo; Han Deman

    2012-01-01

    It is important to study the interaction of ionic liquids (ILs) with protein for the applications of ILs in biochemical process, and help the researchers to choose and design the better ILs to serve as a solvent. In this work, the interaction between 1-alkyl-3-methylimidazolium bromide [C n mim]Br (n=4, 6, 8, 10) and bovine serum albumin (BSA) was systematically investigated for the first time by multi-spectroscopic approach (fluorescence, UV–vis and FT-IR spectroscopy) and density functional theory (DFT). [C n mim]Br (n=4, 6, 8, 10) can bind to BSA by H-bond interaction between their cationic headgroups and Asp/Glu amino acid residue at the surface of BSA, and hydrophobic interaction between their hydrocarbon chains and the hydrophobic amino acid residues in the interior of BSA. On the basis of thermodynamic parameters and the similar structure of [C n mim]Br (n=4, 6, 8, 10), it can be inferred that the hydrophobic interaction plays a major role in the interaction of [C 10 mim]Br with BSA, while the hydrogen bond and van der Waals force play a major role in the interaction of [C n mim]Br (n=4, 6, 8) with BSA. Synchronous fluorescence and FT-IR spectra indicate that [C 10 mim]Br could markedly change the secondary structure of BSA, while [C n mim]Br (n=4, 6, 8) could slightly change the secondary structure of BSA. The results allowed us to understand (i) the effect of the alkyl chain length of the cation on the mechanism of ILs–protein interaction and (ii) the effect of the alkyl chain length of the cation on the protein secondary structure. - Highlights: ► Interaction of [C n mim]Br with BSA was investigated by spectroscopy and DFT. ► Interaction mechanisms and BSA secondary structure were discussed. ► Effects of the alkyl chain length of cation were presented.

  2. Toxic effects of imidazolium ionic liquids on the green seaweed Ulva lactuca: oxidative stress and DNA damage.

    Science.gov (United States)

    Kumar, Manoj; Trivedi, Nitin; Reddy, C R K; Jha, Bhavanath

    2011-11-21

    The green credentials of ionic liquids (ILs) are being increasingly questioned due to the growing evidence of their toxicity to aquatic ecosystems, although the mechanisms of toxicity are unknown. This study provides insights into the mechanism of toxicity and biological effects of 1-alkyl-3-methylimidazolium bromide [C(n)mim]Br (n = 4 to 16) on the marine macroalga Ulva lactuca. The cell viability of this alga during IL exposure was found to be negatively correlated to the chain length of the alkyl group. The IL ([C(12)mim]Br) exposure triggers the generation of reactive oxygen species (ROS viz. O(2)(•-), H(2)O(2), and OH(•)), damage of the membrane and DNA, and inhibition of antioxidant systems in the alga. The enhanced production of ROS and lipid peroxidation in the alga subjected to LC(50) concentration for 4 days was largely attributed to lipoxygenase (LOX) activity coupled with the induction of two LOX isoforms (~80 kDa and ~55 kDa). Pretreatment of the algal thallus with enzyme inhibitors such as diphenylene iodonium, sodium azide, cantharidin, and oxadiazoloquinoxalin-1-one, prior to [C(12)mim]Br exposure showed the regulation of ROS by the activation of membrane bound NADPH-oxidase and cytochrome oxidase. The IL exposure resulted in the accumulation of n-3 and n-6 fatty acids at 0.5 LC(50) concentration indicating the induction of desaturase enzymes. Furthermore, antioxidant enzyme activities such as superoxide dismutase (SOD), ascorbate peroxidase (APX), and glutathione reductase (GR) were enhanced by 1.3-2.0-fold, while glutathione peroxidase (GSH-Px) diminished, together with a higher regeneration rate of reduced ascorbate and glutathione. The isoforms of antioxidant enzymes, namely, Mn-SOD (~85 kDa), APX (~125 and 45 kDa), and GR (~135 kDa) regulated differentially to IL exposure. The comet assay performed for the first time for seaweeds revealed the significant induction of DNA damage (>50-70% increase in % tail DNA over control) in alga exposed

  3. Research on Wheat Straw Pulping with Ionic Liquid 1-Ethyl-3-Methylimidazole Bromide

    Directory of Open Access Journals (Sweden)

    Wei Song

    2016-12-01

    Full Text Available In this paper, the pulping process of wheat straw using ionic liquid 1-ethyl-3-methylimidazolium bromide ([Emim]Br as the digestion liquor is presented. The influence of pulping conditions on the pulp yield are analysed by single-factor and orthogonal experiments, and optimum pulping conditions are obtained. The average pulp yield reaches 44 %, and the average recovery rate of ionic liquid is 93.5 %. The XRD pattern shows no obvious change in the crystal structure of the wheat straw cellulose. Additionally, the SEM image illustrates that there are many fine fibres in the pulp and the spaces between the fibres are large.

  4. Thermal decomposition mechanism of 1-ethyl-3-methylimidazolium bromide ionic liquid.

    Science.gov (United States)

    Chambreau, Steven D; Boatz, Jerry A; Vaghjiani, Ghanshyam L; Koh, Christine; Kostko, Oleg; Golan, Amir; Leone, Stephen R

    2012-06-21

    In order to better understand the volatilization process for ionic liquids, the vapor evolved from heating the ionic liquid 1-ethyl-3-methylimidazolium bromide (EMIM(+)Br(-)) was analyzed via tunable vacuum ultraviolet photoionization time-of-flight mass spectrometry (VUV-PI-TOFMS) and thermogravimetric analysis mass spectrometry (TGA-MS). For this ionic liquid, the experimental results indicate that vaporization takes place via the evolution of alkyl bromides and alkylimidazoles, presumably through alkyl abstraction via an S(N)2 type mechanism, and that vaporization of intact ion pairs or the formation of carbenes is negligible. Activation enthalpies for the formation of the methyl and ethyl bromides were evaluated experimentally, ΔH(‡)(CH(3)Br) = 116.1 ± 6.6 kJ/mol and ΔH(‡)(CH(3)CH(2)Br) = 122.9 ± 7.2 kJ/mol, and the results are found to be in agreement with calculated values for the S(N)2 reactions. Comparisons of product photoionization efficiency (PIE) curves with literature data are in good agreement, and ab initio thermodynamics calculations are presented as further evidence for the proposed thermal decomposition mechanism. Estimates for the enthalpy of vaporization of EMIM(+)Br(-) and, by comparison, 1-butyl-3-methylimidazolium bromide (BMIM(+)Br(-)) from molecular dynamics calculations and their gas phase enthalpies of formation obtained by G4 calculations yield estimates for the ionic liquids' enthalpies of formation in the liquid phase: ΔH(vap)(298 K) (EMIM(+)Br(-)) = 168 ± 20 kJ/mol, ΔH(f, gas)(298 K) (EMIM(+)Br(-)) = 38.4 ± 10 kJ/mol, ΔH(f, liq)(298 K) (EMIM(+)Br(-)) = -130 ± 22 kJ/mol, ΔH(f, gas)(298 K) (BMIM(+)Br(-)) = -5.6 ± 10 kJ/mol, and ΔH(f, liq)(298 K) (BMIM(+)Br(-)) = -180 ± 20 kJ/mol.

  5. Preparation and evaluation of a novel hybrid monolithic column based on pentafluorobenzyl imidazolium bromide ionic liquid.

    Science.gov (United States)

    Shan, Yuanhong; Qiao, Lizhen; Shi, Xianzhe; Xu, Guowang

    2015-01-02

    To develop a novel hybrid monolithic column based on pentafluorobenzyl imidazolium bromide ionic liquid, a new ionic liquid monomer was synthesized from 1-vinylimidazole and pentafluorobenzyl bromide. By employing a facile one-step copolymerization of polyhedral-oligomeric-silsesquioxane-type (POSS) cross-linking agent and the home-made ionic liquid monomer, the hybrid monolithic columns were in situ fabricated in fused-silica capillary. The morphology of monolithic column was characterized by scanning electron microscope (SEM) and the chemical composition was confirmed by Fourier-transform infrared spectroscopy (FT-IR) and elemental analysis. Excellent mechanical stability and slight swelling propensity were exhibited which was ascribed to the rigid hybrid monolithic skeleton. Reproducibility results of run-to-run, column-to-column, batch-to-batch and day-to-day were investigated and the RSDs were less than 0.46%, 1.84%, 3.96% and 3.17%, respectively. The mixed-mode retention mechanism with hydrophobic interaction, π-π stacking, ion-exchange, electrostatic interaction and dipole-dipole interaction was explored systematically using analytes with different structure types. Satisfied separation capability and column efficiency were achieved for the analysis of small molecular compounds such as alkylbenzenes, polycyclic aromatic hydrocarbons, nucleosides and halogenated compounds. Copyright © 2014 Elsevier B.V. All rights reserved.

  6. Synergistic extraction of europium(III) in ammonium ionic liquid

    International Nuclear Information System (INIS)

    Rout, Alok; Venkatesan, K.A.; Antony, M.P.

    2016-01-01

    Room temperature ionic liquids have been receiving increased attention for possible applications in the area of nuclear fuel reprocessing and waste management due to their fascinating properties such as good ionicity, high solvation capability, properties tunable etc. Most of the studies in the literature on the extraction of metal ions with molecular extractants dissolved in ionic liquid diluents are making use of the hydrophobic ionic liquids containing imidazolium cations such as the 1-alkyl-3-methylimidazolium ion. From an environmental point of view, such ionic liquids are not suitable as the primary mode of the metal extraction is by cation exchange mechanism wherein ionic liquid cation is lost to the aqueous phase leading to aqueous contamination and issue of recyclability of organic phase. However, there are some hydrophobic ionic liquids such as trioctylmethylammonium chloride ((N 1888 )(Cl)), and trihexyl(tetradecyl)phoshonium chloride (Cyphos IL 101) that exhibit no cation exchange in the aqueous phase during extraction. In this context, the extraction behavior of europium(III) using a neutral extractant, octyl, phenyl-N.N-diisobutylmethylcarbamoylphophinoxide (CMPO) and/or an acidic extractant bis(ethylhexyl)phosphoric acid (D2EHPA) dissolved in the ammonium ionic liquid diluent, trioctylmethylammonium bis(trifluoromethanesulfonyl)imide, (N 1888 )(NTf 2 ). The extraction behavior of CMPO (or D2EHPA)/(N 1888 )((Tf 2 ) system was investigated as a function of different extraction parameters such as feed acidity, extractant concentration, equilibration time etc.

  7. Ionic liquids: an x-ray reflectivity study

    International Nuclear Information System (INIS)

    Sloutskin, E.; Deutsch, M.; Tamam, L.; Ocko, B.; Kuzmenko, I.; Gog, T.

    2005-01-01

    Full Text:Ionic liquids are non-volatile, non-flammable and thermally stable solvents, and as such are promising 'green' replacements for traditional volatile organic solvents. In the last years hundreds of Ionic liquids were synthesized. Due to the Ionic liquids great industrial potential, this number is growing at an exceedingly fast rate. Despite the great importance of the interfacial properties of materials for technological applications and basic science, the atomic-scale surface structure of the Ionic liquids has never been studied previously. In our study, synchrotron x-ray reflectivity and surface tensiometry were employed to obtain the surface structure and thermodynamics of two ionic liquids, based on the 1-alkyl-3-methylimidazolium cations. A molecular layer of a density ∼18% higher than that of the bulk is found to form at the free surface of these liquids. The excess concentration of the oppositely charged ions within the surface layer is determined by chemical substitution of the anion. Finally, the observed layering at the surface is contrasted with our measurements on the behavior of classical aqueous salt solutions

  8. Bromide as chemical tracer to measure the liquid effluent flow at IPEN-CNEN/SP

    International Nuclear Information System (INIS)

    Silva, Douglas B.; Faustino, Mainara G.; Monteiro, Lucilena R.; Cotrim, Marycel E.B.; Pires, Maria Aparecida F.

    2013-01-01

    Due to recent changes in CONAMA Resolution 357, which occurred through the publication of Resolution 430, on May 13, 2011 that now set standards about the effluent release, IPEN-CNEN/SP initiated several actions to improve the Environmental Monitoring Program (PMA-Q) of stable chemical compounds. Besides various parameters (physical and chemical) established by CONAMA, the submission of an annual pollution inventory report became necessary. The liquid effluent flow measurement is required to implement this inventory. Thereby, this paper describes a study that uses bromide as a chemical tracer. This paper presents the results of 6 tracer releases in IPEN wastewater collection network between 2011 and 2012. Two tracer releases designs were performed: single pulse and continuous releases performed with 1 to 6 hours duration, done by using one single piston pump manufactured by DIONEX. After the release, one fraction of the effluent was collected every 15 minutes at IPEN effluent monitoring station. The tracer concentration in the effluent was analyzed by ion chromatography and flow was calculated considering the dilution in the system and pump flow set up for the release. The flow values were measured in 6 events were determined and evaluated as per Brazilian regulation requirements. Experimental designs to be implemented during 2013 monitoring were also discussed in this paper, contributing to legal compliance and to improve IPEN's Environmental Monitoring Program for stable chemical compounds (PMA-Q). (author)

  9. Hg⁰ removal from flue gas by ionic liquid/H₂O₂.

    Science.gov (United States)

    Cheng, Guangwen; Bai, Bofeng; Zhang, Qiang; Cai, Ming

    2014-09-15

    1-Alkyl-3-methylimidazolium chloride ionic liquids ([Cnmim] Cl, n=4, 6, 8) were prepared. The ionic liquid was then mixed with hydrogen peroxide (H2O2) to form an absorbent. The Hg(0) removal performance of the absorbent was investigated in a gas/liquid scrubber using simulated flue gas. It was found that the ionic liquid/H2O2 mixture was an excellent absorbent and could be used to remove Hg(0) from flue gas. When the mass ratio of H2O2 to ionic liquid was 0.5, the absorbent showed high Hg(0) removal efficiency (up to 98%). The Hg(0) removal efficiency usually increased with the absorption temperature, while decreased with the increase of alkyl chain length in ionic liquid molecule. The Hg(0) removal mechanism involved with Hg(0) oxidation by H2O2 and Hg(2+) transfer from aqueous phase to ionic liquid phase. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Vapor-liquid equilibria of the water + 1,3-propanediol and water + 1,3-propanediol + lithium bromide systems

    Energy Technology Data Exchange (ETDEWEB)

    Mun, S Y; Lee, H

    1999-12-01

    Vapor-liquid equilibrium data of the water + 1,3-propanediol and water + 1,3-propanediol + lithium bromide systems were measured at 60, 160, 300, and 760 mmHg at temperatures ranging from 315 to 488 K. The apparatus used in this work is a modified still especially designed for the measurement of low-pressure VLE, in which both liquid and vapor are continuously recirculated. For the analysis of salt-containing solutions, a method incorporating refractometry and gravimetry was used. From the experimental measurements, the effect of lithium bromide on the VLE behavior of water + 1,3-propanediol was investigated. The experimental data of the salt-free system were successfully correlated using the Wilson, NRTL, and UNIQUAC models. In addition, the extended UNIQUAC model of Sander et al. was applied to the VLE calculation of salt-containing mixtures.

  11. Application of ionic liquids in electrochemical sensing systems.

    Science.gov (United States)

    Shiddiky, Muhammad J A; Torriero, Angel A J

    2011-01-15

    Since 1992, when the room temperature ionic liquids (ILs) based on the 1-alkyl-3-methylimidazolium cation were reported to provide an attractive combination of an electrochemical solvent and electrolyte, ILs have been widely used in electrodeposition, electrosynthesis, electrocatalysis, electrochemical capacitor, and lithium batteries. However, it has only been in the last few years that electrochemical biosensors based on carbon ionic liquid electrodes (CILEs) and IL-modified macrodisk electrodes have been reported. However, there are still a lot of challenges in achieving IL-based sensitive, selective, and reproducible biosensors for high speed analysis of biological and environmental compounds of interest. This review discusses the principles of operation of electrochemical biosensors based on CILEs and IL/composite-modified macrodisk electrodes. Subsequently, recent developments and major strategies for enhancing sensing performance are discussed. Key challenges and opportunities of IL-based biosensors to further development and use are considered. Emphasis is given to direct electron-transfer reaction and electrocatalysis of hemeproteins and enzyme-modified composite electrodes. Copyright © 2010 Elsevier B.V. All rights reserved.

  12. Viscometric studies of interactions between ionic liquid 1-octyl-3-methyl-imidazolium bromide and polyvinyl pyrrolidone in aqueous solutions

    International Nuclear Information System (INIS)

    Mehrdad, Abbas; Shekaari, Hemayat; Niknam, Zahra

    2014-01-01

    Highlights: • Viscosities of PVP in aqueous solution of IL are measured. • The flow activation energies are calculated. • The flow activation energies are correlated in terms of polymer concentration. • Intrinsic viscosity of PVP is decreased by increasing temperature. - Abstract: Ionic liquids are investigated as solvents for polymerization processes, as plasticizers of various kinds of polymers and as components of the polymeric matrixes. In this research, viscosity of polyvinyl pyrrolidone in aqueous solution of ionic liquid, 1-octyl-3-methyl imidazolium bromide are measured at various temperatures. The flow activation energies are calculated and correlated in terms of polymer concentration. From sign of the initial slope of the activation energy versus polymer concentration at zero concentration, it is concluded that thermodynamic quality of ionic liquid aqueous solutions are reduced by increasing temperature. The value of the intrinsic viscosity of polyvinyl pyrrolidone was determined using Huggins equation and thermodynamic parameters of this polymer were calculated on the basis of intrinsic viscosity. Also the effect of ionic liquid, 1-octyl-3-methyl imidazolium bromide on the thermodynamic parameters of dilute aqueous polyvinyl pyrrolidone solutions, such as (polymer + solvent) interaction parameter, theta temperature, the heat of dilution parameter and the entropy of dilution parameter was investigated. Results suggest that the thermodynamic quality of water was increased slightly by the addition of ionic liquid in aqueous solution of polyvinyl pyrrolidone

  13. Ionic liquids based simultaneous ultrasonic and microwave assisted extraction of phenolic compounds from burdock leaves

    International Nuclear Information System (INIS)

    Lou Zaixiang; Wang Hongxin; Zhu Song; Chen Shangwei; Zhang Ming; Wang Zhouping

    2012-01-01

    The ionic liquids based simultaneous ultrasonic and microwave assisted extraction (IL-UMAE) technique was first proposed and applied to isolate compounds. The ionic liquids comprising a range of four anions, five 1-alkyl-3-methylimidazolium derivatives were designed and prepared. The results suggested that varying the anion and cation both had apparent effects on the extraction of phenolics. The results also showed that irradiation power, time and solid–liquid ratio significantly affected the yields. The yields of caffeic acid and quercetin obtained by IL-UMAE were higher than those by regular UMAE. Compared with conventional heat-reflux extraction (HRE), the proposed approach exhibited higher efficiency (8–17% enhanced) and shorter extraction time (from 5 h to 30 s). The results indicated ILUMAE to be a fast and efficient extraction technique. Moreover, the proposed method was validated by the reproducibility and recovery experiments. The ILUMAE method provided good recoveries (from 96.1% to 105.3%) with RSD lower than 5.2%, which indicated that the proposed method was credible. Based on the designable nature of ionic liquids, and the rapid and highly efficient performance of the proposed approach, ILUMAE provided a new alternative for preparation of various useful substances from solid samples.

  14. The effect of the alkyl chain length on physicochemical features of (ionic liquids + γ-butyrolactone) binary mixtures

    International Nuclear Information System (INIS)

    Papović, Snežana; Bešter-Rogač, Marija; Vraneš, Milan; Gadžurić, Slobodan

    2016-01-01

    Highlights: • Influence of alkyl substituent length on IL properties was studied. • Nature of interactions between studied [C_nC_1im][NTf_2] and GBL were discussed. • Angell strength parameter indicates [C_nC_1im][NTf_2] are fragile liquids. • ILs properties regularly change with increase of the alkyl chain length. • Absence of GBL self-association upon addition of IL is observed. - Abstract: Densities and viscosities were determined and analysed for γ-butyrolactone (GBL) binary mixtures with 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ionic liquids (where alkyl = ethyl, hexyl, octyl) as a function of temperature at atmospheric pressure (p = 0.1 MPa) and over the whole composition range. Excess molar volumes have been calculated from the experimental densities and were fitted using Redlich–Kister’s polynomial equation. Other volumetric parameters have been also calculated in order to obtain information about interactions between GBL and imidazolium based ionic liquids with different alkyl chain length. From the viscosity measurements, the Angell strength parameter was calculated for pure ionic liquids indicating that all investigated electrolytes are “fragile” liquids.

  15. Phase behaviour, interactions, and structural studies of (amines+ionic liquids) binary mixtures.

    Science.gov (United States)

    Jacquemin, Johan; Bendová, Magdalena; Sedláková, Zuzana; Blesic, Marijana; Holbrey, John D; Mullan, Claire L; Youngs, Tristan G A; Pison, Laure; Wagner, Zdeněk; Aim, Karel; Costa Gomes, Margarida F; Hardacre, Christopher

    2012-05-14

    We present a study on the phase equilibrium behaviour of binary mixtures containing two 1-alkyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}imide-based ionic liquids, [C(n)mim] [NTf(2)] (n=2 and 4), mixed with diethylamine or triethylamine as a function of temperature and composition using different experimental techniques. Based on this work, two systems showing an LCST and one system with a possible hourglass shape are measured. Their phase behaviours are then correlated and predicted by using Flory-Huggins equations and the UNIQUAC method implemented in Aspen. The potential of the COSMO-RS methodology to predict the phase equilibria was also tested for the binary systems studied. However, this methodology is unable to predict the trends obtained experimentally, limiting its use for systems involving amines in ionic liquids. The liquid-state structure of the binary mixture ([C(2)mim] [NTf(2)]+diethylamine) is also investigated by molecular dynamics simulation and neutron diffraction. Finally, the absorption of gaseous ethane by the ([C(2)mim][NTf(2)]+diethylamine) binary mixture is determined and compared with that observed in the pure solvents. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Thermophysical properties of ionic liquid {1-butyl-3-methylimidazolium bromide [bmim][Br] in alkoxyalkanols + water} mixtures at different temperatures

    International Nuclear Information System (INIS)

    Pal, Amalendu; Kumar, Harsh; Kumar, Bhupinder; Sharma, Pooja; Kaur, Kirtanjot

    2013-01-01

    Highlights: ► Densities and speeds of sound of alkoxyalkanols in [bmim][Br]. ► Synthesis of room temperature ionic liquid [bmim][Br]. ► Partial molar volumes and compressibility of transfer. ► Apparent molar expansivities and the Hepler’s constant were calculated. ► Solute–solute and solute–solvent interactions and the structural changes of the solutes. - Abstract: The interactions of alkoxyalkanols with the ionic liquid 1-butyl-3-methylimidazolium bromide [bmim][Br] as a function of temperature were investigated by combination of volumetric and acoustic methods. The density, ρ, and speed of sound, u, of ethylene glycol monomethyl ether, diethylene glycol monomethyl ether, and triethylene glycol monomethyl ether (0.00–1.01 mol·kg −1 ) in aqueous 1-butyl-3-methylimidazolium bromide solutions ranging from pure water to 0.29 mass% of ionic liquid have been measured at T = (288.15, 298.15 and 308.15) K and atmospheric pressure. The apparent molar volume (V φ ) and adiabatic compressibility (K φ,S ) of alkoxyalkanols in aqueous ionic liquid solution were determined at the measured temperatures. The partial molar volume (V φ 0 ) and partial molar adiabatic compressibility (K φ 0 ) of alkoxyalkanols at infinite dilution were evaluated. Transfer volumes (ΔV φ 0 ) and transfer adiabatic compressibility (ΔK φ 0 ) at infinite dilution from water to aqueous ionic liquid solution were also calculated. The temperature dependence of the apparent molar volume was used to calculate apparent molar expansivity (φ E 0 ) and the Hepler’s constant values, (∂ 2 V φ 0 /∂T 2 ). The results were explained on the basis of competing patterns of interactions of co-solvent and the solute.

  17. Effects of imidazolium chloride ionic liquids and their toxicity to Scenedesmus obliquus.

    Science.gov (United States)

    Liu, Huijun; Zhang, Xiaoqiang; Chen, Caidong; Du, Shaoting; Dong, Ying

    2015-12-01

    The low volatility of ionic liquids effectively eliminates a major pathway for environmental release and contamination; however, the good solubility, low degree of environmental degradation and biodegradation of ILs may pose a potential threat to the aquatic environment. The growth inhibition of the green alga Scenedesmus obliquus by five 1-alkyl-3-methylimidazolium chloride ionic liquids (ILs) ([Cnmim]Cl, n=6, 8, 10, 12, 16) was investigated, and the effect on cellular membrane permeability and the ultrastructural morphology by ILs ([Cnmim]Cl, n=8, 12, 16) were studied. The results showed that the growth inhibition rate increased with increasing IL concentration and increasing alkyl chain lengths. The relative toxicity was determined to be [C6mim]Cl<[C8mim]Cl<[C10mim]Cl<[C12mim]Cl<[C16mim]Cl. The algae were most sensitive to imidazolium chloride ILs at 48 h according to the results from the growth inhibition rate and cellular membrane permeability tests. The ultrastructural morphology showed that the ILs had negative effects on the cellular morphology and structure of the algae. The cell wall of treated algae became wavy and separated from the cell membrane. Chloroplast grana lamellae became obscure and loose, osmiophilic material was deposited in the chloroplast, and mitochondria and their cristae swelled. Additionally, electron-dense deposits were observed in the vacuoles. Copyright © 2015 Elsevier Inc. All rights reserved.

  18. Revisiting imidazolium based ionic liquids: Effect of the conformation bias of the [NTf2] anion studied by molecular dynamics simulations

    Science.gov (United States)

    Neumann, Jan; Golub, Benjamin; Odebrecht, Lisa-Marie; Ludwig, Ralf; Paschek, Dietmar

    2018-05-01

    We study ionic liquids composed of 1-alkyl-3-methylimidazolium cations and bis(trifluoromethyl-sulfonyl)imide anions ([CnMIm][NTf2]) with varying chain-length n = 2, 4, 6, 8 by using molecular dynamics simulations. We show that a reparametrization of the dihedral potentials as well as charges of the [NTf2] anion leads to an improvement of the force field model introduced by Köddermann, Paschek, and Ludwig [ChemPhysChem 8, 2464 (2007)] (KPL-force field). A crucial advantage of the new parameter set is that the minimum energy conformations of the anion (trans and gauche), as deduced from ab initio calculations and Raman experiments, are now both well represented by our model. In addition, the results for [CnMIm][NTf2] show that this modification leads to an even better agreement between experiment and molecular dynamics simulation as demonstrated for densities, diffusion coefficients, vaporization enthalpies, reorientational correlation times, and viscosities. Even though we focused on a better representation of the anion conformation, also the alkyl chain-length dependence of the cation behaves closer to the experiment. We strongly encourage to use the new NGOLP (Neumann, Golub, Odebrecht, Ludwig, Paschek) force field for the [NTf2] anion instead of the earlier KPL parameter set for computer simulations aiming to describe the thermodynamics, dynamics, and also structure of imidazolium-based ionic liquids.

  19. Thermophysical Properties of Homologous Tetracyanoborate-Based Ionic Liquids Using Experiments and Molecular Dynamics Simulations.

    Science.gov (United States)

    Koller, Thomas M; Ramos, Javier; Schulz, Peter S; Economou, Ioannis G; Rausch, Michael H; Fröba, Andreas P

    2017-04-27

    Thermophysical properties of low-viscosity ionic liquids (ILs) based on the tetracyanoborate ([B(CN) 4 ] - ) anion carrying a homologous series of 1-alkyl-3-methylimidazolium ([AMIM] + ) cations [EMIM] + (ethyl), [BMIM] + (butyl), [HMIM] + (hexyl), [OMIM] + (octyl), and [DMIM] + (decyl) were investigated by experimental methods and molecular dynamics (MD) simulations at atmospheric pressure and various temperatures. Spectroscopic methods based on nuclear magnetic resonance and surface light scattering were applied to measure the ion self-diffusion coefficients and dynamic viscosity, respectively. In terms of MD simulations, a nonpolarizable molecular model for [EMIM][B(CN) 4 ] developed by optimization to experimental data was transferred to the other homologous ILs. For the appropriate description of the inter- and intramolecular interactions, precise and approximate force fields (FFs) were tested regarding their transferability within the homologous IL series, aiming at reducing the computational effort in molecular simulations. It is shown that at comparable simulated and experimental densities, the calculated and measured data for viscosity and self-diffusion coefficients of the ILs agree well mostly within combined uncertainties, but deviate stronger for longer-chained ILs using an overly coarse FF model. For the [B(CN) 4 ] - -based ILs studied, a comparison with literature data, the influence of varying alkyl chain length in the cation on their structural and thermophysical properties, and a correlation between self-diffusivity and viscosity are discussed.

  20. Measurement and correlation of vapor-liquid equilibria for a binary system containing 1-butyl-3-methylimidazolium tridecafluorohexyl sulfonate and carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Soon Kang; Park, Yoon Kook [Hongik University, Sejong (Korea, Republic of)

    2016-01-15

    Using a high-pressure variable-volume view cell, the vapor-liquid equilibria of the binary system CO{sub 2} and 1-butyl-3-methylimidazolium tridecafluorohexylsulfonate ([BMIM][TDfO]) were determined. The CO{sub 2} mole fraction ranged from 0.104 to 0.952 over a temperature range of 298.2-323.2 K. Both the Peng-Robinson and Soave-Redlich- Kwong equations of state were applied with two different mixing rules to correlate with the experimentally obtained results. Increasing the alkyl chain length in perfluorinated sulfonate anion mother structure from methyl to hexyl markedly increased the CO{sub 2} solubility. To investigate the effect of the number of fluorine atoms in the anion on the phase behavior of imidazolium-based ionic liquid, these experimental results were then compared with those reported in previous experimental studies of 1-alkyl-3-methylimidazolium cations-including ionic liquid+CO{sub 2} binary system.

  1. Making sense of enthalpy of vaporization trends for ionic liquids: new experimental and simulation data show a simple linear relationship and help reconcile previous data.

    Science.gov (United States)

    Verevkin, Sergey P; Zaitsau, Dzmitry H; Emel'yanenko, Vladimir N; Yermalayeu, Andrei V; Schick, Christoph; Liu, Hongjun; Maginn, Edward J; Bulut, Safak; Krossing, Ingo; Kalb, Roland

    2013-05-30

    Vaporization enthalpy of an ionic liquid (IL) is a key physical property for applications of ILs as thermofluids and also is useful in developing liquid state theories and validating intermolecular potential functions used in molecular modeling of these liquids. Compilation of the data for a homologous series of 1-alkyl-3-methylimidazolium bis(trifluoromethane-sulfonyl)imide ([C(n)mim][NTf2]) ILs has revealed an embarrassing disarray of literature results. New experimental data, based on the concurring results from quartz crystal microbalance, thermogravimetric analyses, and molecular dynamics simulation have revealed a clear linear dependence of IL vaporization enthalpies on the chain length of the alkyl group on the cation. Ambiguity of the procedure for extrapolation of vaporization enthalpies to the reference temperature 298 K was found to be a major source of the discrepancies among previous data sets. Two simple methods for temperature adjustment of vaporization enthalpies have been suggested. Resulting vaporization enthalpies obey group additivity, although the values of the additivity parameters for ILs are different from those for molecular compounds.

  2. Mechanical heterogeneity in ionic liquids

    Science.gov (United States)

    Veldhorst, Arno A.; Ribeiro, Mauro C. C.

    2018-05-01

    Molecular dynamics (MD) simulations of five ionic liquids based on 1-alkyl-3-methylimidazolium cations, [CnC1im]+, have been performed in order to calculate high-frequency elastic moduli and to evaluate heterogeneity of local elastic moduli. The MD simulations of [CnC1im][NO3], n = 2, 4, 6, and 8, assessed the effect of domain segregation when the alkyl chain length increases, and [C8C1im][PF6] assessed the effect of strength of anion-cation interaction. Dispersion curves of excitation energies of longitudinal and transverse acoustic, LA and TA, modes were obtained from time correlation functions of mass currents at different wavevectors. High-frequency sound velocity of LA modes depends on the alkyl chain length, but sound velocity for TA modes does not. High-frequency bulk and shear moduli, K∞ and G∞, depend on the alkyl chain length because of a density effect. Both K∞ and G∞ are strongly dependent on the anion. The calculation of local bulk and shear moduli was accomplished by performing bulk and shear deformations of the systems cooled to 0 K. The simulations showed a clear connection between structural and elastic modulus heterogeneities. The development of nano-heterogeneous structure with increasing length of the alkyl chain in [CnC1im][NO3] implies lower values for local bulk and shear moduli in the non-polar domains. The mean value and the standard deviations of distributions of local elastic moduli decrease when [NO3]- is replaced by the less coordinating [PF6]- anion.

  3. Calorimetric determination of the enthalpy of 1-butyl-3-methylimidazolium bromide synthesis: a key quantity in thermodynamics of ionic liquids.

    Science.gov (United States)

    Paulechka, Yauheni U; Kabo, Andrey G; Blokhin, Andrey V

    2009-11-05

    The enthalpy of the 1-butyl-3-methylimidazolium bromide [C(4)mim]Br ionic liquid synthesis reaction 1-methylimidazole (liq) + 1-bromobutane (liq) --> [C(4)mim]Br (liq) was determined in a homemade small-volume isoperibol calorimeter to be Delta(r)H degrees (298) = -87.7 +/- 1.6 kJ x mol(-1). The activation energy for this reaction in a homogeneous system E(A) = 73 +/- 4 kJ x mol(-1) was found from the results of calorimetric measurements. The formation enthalpies for the crystalline and liquid [C(4)mim]Br were determined from the calorimetric data: Delta(f)H degrees (298)(cr) = -178 +/- 5 kJ x mol(-1) and Delta(f)H degrees (298)(liq) = -158 +/- 5 kJ x mol(-1). The ideal-gas formation enthalpy of this compound Delta(f)H degrees (298)(g) = 16 +/- 7 kJ x mol(-1) was calculated using the methods of quantum chemistry and statistical thermodynamics. The vaporization enthalpy of [C(4)mim]Br, Delta(vap)H degrees (298) = 174 +/- 9 kJ x mol(-1), was estimated from the experimental and calculated formation enthalpies. It was demonstrated that vapor pressure of this ionic liquid cannot be experimentally determined.

  4. Water in Room Temperature Ionic Liquids

    Science.gov (United States)

    Fayer, Michael

    2014-03-01

    Room temperature ionic liquids (or RTILs, salts with a melting point below 25 °C) have become a subject of intense study over the last several decades. Currently, RTIL application research includes synthesis, batteries, solar cells, crystallization, drug delivery, and optics. RTILs are often composed of an inorganic anion paired with an asymmetric organic cation which contains one or more pendant alkyl chains. The asymmetry of the cation frustrates crystallization, causing the salt's melting point to drop significantly. In general, RTILs are very hygroscopic, and therefore, it is of interest to examine the influence of water on RTIL structure and dynamics. In addition, in contrast to normal aqueous salt solutions, which crystallize at low water concentration, in an RTIL it is possible to examine isolated water molecules interacting with ions but not with other water molecules. Here, optical heterodyne-detected optical Kerr effect (OHD-OKE) measurements of orientational relaxation on a series of 1-alkyl-3-methylimidazolium tetrafluoroborate RTILs as a function of chain length and water concentration are presented. The addition of water to the longer alkyl chain RTILs causes the emergence of a long time bi-exponential orientational anisotropy decay. Such decays have not been seen previously in OHD-OKE experiments on any type of liquid and are analyzed here using a wobbling-in-a-cone model. The orientational relaxation is not hydrodynamic, with the slowest relaxation component becoming slower as the viscosity decreases for the longest chain, highest water content samples. The dynamics of isolated D2O molecules in 1-butyl-3-methylimidazolium hexafluorophosphate (BmImPF6) were examined using two dimensional infrared (2D IR) vibrational echo spectroscopy. Spectral diffusion and incoherent and coherent transfer of excitation between the symmetric and antisymmetric modes are examined. The coherent transfer experiments are used to address the nature of inhomogeneous

  5. Cation symmetry effect on the volatility of ionic liquids.

    Science.gov (United States)

    Rocha, Marisa A A; Coutinho, João A P; Santos, Luís M N B F

    2012-09-06

    This work reports the first data for the vapor pressures at several temperatures of the ionic liquids, [C(N/2)C(N/2)im][NTf(2)] (N = 4, 6, 8, 10, 12) measured using a Knudsen effusion apparatus combined with a quartz crystal microbalance. The morphology and the thermodynamic parameters of vaporization derived from the vapor pressures, are compared with those for the 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide series, [C(N-1)C(1)im][NTf(2)] (N = 3 - 9, 11, and 13). It was found that the volatility of [C(N/2)C(N/2)im][NTf(2)] series is significantly higher than the asymmetric cation ILs with the same total number of carbons in the alkyl side chains, [C(N-1)C(1)im][NTf(2)]. The observed higher volatility is related with the lower enthalpy of vaporization. The symmetric cation, [C(N/2)C(N/2)im][NTf(2)], presents lower entropies of vaporization compared with the asymmetric [C(N-1)C(1)im][NTf(2)], indicating an increase of the absolute liquid entropy in the symmetric cation ILs, being a reflection of a change of the ion dynamics in the IL liquid phase. Moreover both the enthalpy and entropy of vaporization of the [C(N/2)C(N/2)im][NTf(2)] ILs, present a clear odd-even effect with higher enthalpies/entropies of vaporization for the odd number of carbons in each alkyl chain ([C(3)C(3)im][NTf(2)] and [C(5)C(5)im][NTf(2)]).

  6. Application of ionic liquids based enzyme-assisted extraction of chlorogenic acid from Eucommia ulmoides leaves

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Tingting; Sui, Xiaoyu, E-mail: suixiaoyu@outlook.com; Li, Li; Zhang, Jie; Liang, Xin; Li, Wenjing; Zhang, Honglian; Fu, Shuang

    2016-01-15

    A new approach for ionic liquid based enzyme-assisted extraction (ILEAE) of chlorogenic acid (CGA) from Eucommia ulmoides is presented in which enzyme pretreatment was used in ionic liquids aqueous media to enhance extraction yield. For this purpose, the solubility of CGA and the activity of cellulase were investigated in eight 1-alkyl-3-methylimidazolium ionic liquids. Cellulase in 0.5 M [C6mim]Br aqueous solution was found to provide better performance in extraction. The factors of ILEAE procedures including extraction time, extraction phase pH, extraction temperatures and enzyme concentrations were investigated. Moreover, the novel developed approach offered advantages in term of yield and efficiency compared with other conventional extraction techniques. Scanning electronic microscopy of plant samples indicated that cellulase treated cell wall in ionic liquid solution was subjected to extract, which led to more efficient extraction by reducing mass transfer barrier. The proposed ILEAE method would develope a continuous process for enzyme-assisted extraction including enzyme incubation and solvent extraction process. In this research, we propose a novel view for enzyme-assisted extraction of plant active component, besides concentrating on enzyme facilitated cell wall degradation, focusing on improvement of bad permeability of ionic liquids solutions. - Highlights: • An ionic liquid based enzyme-assisted extraction method of natural product was explored. • ILEAE utilizes enzymatic treatment to improve permeability of ionic liquids solution. • Enzyme incubation and solvent extraction process were ongoing simultaneously. • ILEAE process simplified operating process and suitable for more complete extraction.

  7. Application of ionic liquids based enzyme-assisted extraction of chlorogenic acid from Eucommia ulmoides leaves

    International Nuclear Information System (INIS)

    Liu, Tingting; Sui, Xiaoyu; Li, Li; Zhang, Jie; Liang, Xin; Li, Wenjing; Zhang, Honglian; Fu, Shuang

    2016-01-01

    A new approach for ionic liquid based enzyme-assisted extraction (ILEAE) of chlorogenic acid (CGA) from Eucommia ulmoides is presented in which enzyme pretreatment was used in ionic liquids aqueous media to enhance extraction yield. For this purpose, the solubility of CGA and the activity of cellulase were investigated in eight 1-alkyl-3-methylimidazolium ionic liquids. Cellulase in 0.5 M [C6mim]Br aqueous solution was found to provide better performance in extraction. The factors of ILEAE procedures including extraction time, extraction phase pH, extraction temperatures and enzyme concentrations were investigated. Moreover, the novel developed approach offered advantages in term of yield and efficiency compared with other conventional extraction techniques. Scanning electronic microscopy of plant samples indicated that cellulase treated cell wall in ionic liquid solution was subjected to extract, which led to more efficient extraction by reducing mass transfer barrier. The proposed ILEAE method would develope a continuous process for enzyme-assisted extraction including enzyme incubation and solvent extraction process. In this research, we propose a novel view for enzyme-assisted extraction of plant active component, besides concentrating on enzyme facilitated cell wall degradation, focusing on improvement of bad permeability of ionic liquids solutions. - Highlights: • An ionic liquid based enzyme-assisted extraction method of natural product was explored. • ILEAE utilizes enzymatic treatment to improve permeability of ionic liquids solution. • Enzyme incubation and solvent extraction process were ongoing simultaneously. • ILEAE process simplified operating process and suitable for more complete extraction.

  8. The influence of mesoscopic confinement on the dynamics of imidazolium-based room temperature ionic liquids in polyether sulfone membranes

    Science.gov (United States)

    Thomaz, Joseph E.; Bailey, Heather E.; Fayer, Michael D.

    2017-11-01

    The structural dynamics of a series of 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (CnmimNTf2, n = 2, 4, 6, 10: ethyl—Emim; butyl—Bmim; hexyl—Hmim; decyl—Dmim) room temperature ionic liquids confined in the pores of polyether sulfone (PES 200) membranes with an average pore size of ˜350 nm and in the bulk liquids were studied. Time correlated single photon counting measurements of the fluorescence of the fluorophore coumarin 153 (C153) were used to observe the time-dependent Stokes shift (solvation dynamics). The solvation dynamics of C153 in the ionic liquids are multiexponential decays. The multiexponential functional form of the decays was confirmed as the slowest decay component of each bulk liquid matches the slowest component of the liquid dynamics measured by optical heterodyne-detected optical Kerr effect (OHD-OKE) experiments, which is single exponential. The fact that the slowest component of the Stokes shift matches the OHD-OKE data in all four liquids identifies this component of the solvation dynamics as arising from the complete structural randomization of the liquids. Although the pores in the PES membranes are large, confinement on the mesoscopic length scale results in substantial slowing of the dynamics, a factor of ˜4, for EmimNTf2, with the effect decreasing as the chain length increases. By DmimNTf2, the dynamics are virtually indistinguishable from those in the bulk liquid. The rotation relaxation of C153 in the four bulk liquids was also measured and showed strong coupling between the C153 probe and its environment.

  9. Modeling gas solubilities in imidazolium based ionic liquids with the [Tf2N] anion using the GC-EoS

    NARCIS (Netherlands)

    Pereda, Selva; Raeissi, Sonia; Andreatta, A.E. (Alfonsina); Bottini, Susana B.; Kroon, Maaike; Peters, Cor

    2016-01-01

    The group contribution equation of state (GC-EoS) is extended to model gas solubilities in the homologous 1-alkyl-3-methylimidazolium bis(trifluoromethyl-sulfonyl) imide family. The gases considered in this work are CO2, CO, H2, CH4, and C2H6. The model parameters were estimated on the basis of 1400

  10. Influence of Cetyltrimethylammonium Bromide on Gold Nanocrystal Formation Studied by in Situ Liquid Cell Scanning Transmission Electron Microscopy

    DEFF Research Database (Denmark)

    Canepa, Silvia A.; Sneed, Brian T.; Sun, Hongyu

    2018-01-01

    The synthesis of monodisperse size- and shape-controlled Au nanocrystals is often achieved with cetyltrimethylammonium bromide (CTAB) surfactant; however, its role in the growth of such tailored nanostructures is not well understood. To elucidate the formation mechanism(s) and evolution of the mo...

  11. Can the scaling behavior of electric conductivity be used to probe the self-organizational changes in solution with respect to the ionic liquid structure? The case of [C8MIM][NTf2].

    Science.gov (United States)

    Paluch, Marian; Wojnarowska, Zaneta; Goodrich, Peter; Jacquemin, Johan; Pionteck, Jürgen; Hensel-Bielowka, Stella

    2015-08-28

    Electrical conductivity of the supercooled ionic liquid [C8MIM][NTf2], determined as a function of temperature and pressure, highlights strong differences in its ionic transport behavior between low and high temperature regions. To date, the crossover effect which is very well known for low molecular van der Waals liquids has been rarely described for classical ionic liquids. This finding highlights that the thermal fluctuations could be dominant mechanisms driving the dramatic slowing down of ion motions near Tg. An alternative way to analyze separately low and high temperature dc-conductivity data using a density scaling approach was then proposed. Based on which a common value of the scaling exponent γ = 2.4 was obtained, indicating that the applied density scaling is insensitive to the crossover effect. By comparing the scaling exponent γ reported herein along with literature data for other ionic liquids, it appears that γ decreases by increasing the alkyl chain length on the 1-alkyl-3-methylimidazolium-based ionic liquids. This observation may be related to changes in the interaction between ions in solution driven by an increase in the van der Waals type interaction by increasing the alkyl chain length on the cation. This effect may be related to changes in the ionic liquid nanostructural organization with the alkyl chain length on the cation as previously reported in the literature based on molecular dynamic simulations. In other words, the calculated scaling exponent γ may be then used as a key parameter to probe the interaction and/or self-organizational changes in solution with respect to the ionic liquid structure.

  12. Influence of the ionic liquid 1-butyl-3-methylimidazolium bromide on amyloid fibrillogenesis in lysozyme: Evidence from photophysical and imaging studies.

    Science.gov (United States)

    Basu, Anirban; Bhattacharya, Subhash Chandra; Kumar, Gopinatha Suresh

    2018-02-01

    Many proteins can abnormally fold to form pathological amyloid deposits/aggregates that are responsible for various degenerative disorders called amyloidosis. Here we have examined the anti-amyloidogenic potency of an ionic liquid, 1-butyl-3-methylimidazolium bromide, using lysozyme as a model system. Thioflavin T fluorescence assay demonstrated that the ionic liquid suppressed the formation of lysozyme fibrils significantly. This observation was further confirmed by the Congo red assay. Fluorescence microscopy, intrinsic fluorescence studies, nile red fluorescence assay, ANS binding assay and circular dichroism studies also testified diminishing of the fibrillogenesis in the presence of ionic liquid. Formation of amyloid fibrils was also characterized by α to β conformational transition. From far-UV circular dichroism studies it was observed that the β-sheet content of the lysozyme samples decreased in the presence of the ionic liquid which in turn implied that fibrillogenesis was supressed by the ionic liquid. Atomic force microscopy imaging unequivocally established that the ionic liquid attenuated fibrillogenesis in lysozyme. These results may be useful for the development of more effective therapeutics for amyloidosis. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Thermophysical properties of ionic liquid, 1-hexyl-3-methylimidazolum bromide + N-N′bis(2-pyridylmethylidene)-1,2-diiminoethane (BPIE) Schiff base + N,N-dimethylformamide solutions

    International Nuclear Information System (INIS)

    Shekaari, Hemayat; Bezaatpour, Abolfazl; Khoshalhan, Maryam

    2012-01-01

    Highlights: ► Thermodynamic properties of ionic liquids + BPIE Schiff base + DMF were studied. ► There are preferential interactions between ionic liquid and BPIE molecules. ► The nonpolar–nonpolar interactions are dominant interactions between BPIE and ionic liquid. - Abstract: Effect of N-N′bis(2-pyridylmethylidene)-1,2-diiminoethane (BPIE) Schiff base on thermodynamic properties of ionic liquid, 1-hexyl-3-methylimidazolium bromide ([HMIm]Br) in N,N-dimethylformamide (DMF) solutions were determined at T = 298.15–313.15 K. The standard partial molar volumes, V φ 0 , partial molar volumes of transfer, Δ tr V φ 0 have been calculated using the measured density data. The cosphere overlap model was used to interpretate the partial molar volumes of transfer, Δ tr V φ 0 . The calculated Hepler's constants, ∂ 2 V φ 0 /∂ 2 T, indicate that the BPIE and ionic liquid have structure-breaking (chaotropic) tendency. Ion association constants, K a , and limiting molar conductivities, Λ 0 , viscosity B-coefficients and molar refractions, R D , have been used to confirm the conclusions obtained from the volumetric properties. The results were interpreted in terms of various solute–solvent interactions occuring in the investigated solutions and indicating an enhancement in the nonpolar–nonpolar interactions between the BPIE Schiff base and the ionic liquid with increasing BPIE concentration.

  14. Systematic study of the thermophysical properties of imidazolium-based ionic liquids with cyano-functionalized anions.

    Science.gov (United States)

    Neves, Catarina M S S; Kurnia, Kiki Adi; Coutinho, João A P; Marrucho, Isabel M; Lopes, José N Canongia; Freire, Mara G; Rebelo, Luís Paulo N

    2013-09-05

    In the past few years, ionic liquids (ILs) with cyano-functionalized anions have shown to be improved candidates for electrochemical and separation applications. Nevertheless, only scattered data exist hitherto and a broad analysis of their structure-property relationship has yet to be attempted. Therefore, in this work, a systematic study of the densities, viscosities and refractive indices of imidazolium-based ILs with cyano-functionalized anions was carried out at 0.1 MPa within a broad temperature range (from 278 to 363 K). The ILs under study are based on 1-alkyl-3-methylimidazolium cations (alkyl = ethyl, butyl and hexyl) combined with the [SCN](-), [N(CN)2](-), [C(CN)3](-) and [B(CN)4](-) anions. The selected matrix of cation/anion combinations allows us to provide a detailed and comprehensive investigation of the influence of the -CN group through an analysis of the thermophysical properties of the related ILs. The results show that, regardless of the cation, the densities decrease with an increase in the number of cyano groups or anion molecular weight. Moreover, for a fixed cation and temperature, the refractive index of the ILs decreases according to the rank: [SCN](-) > [N(CN)2](-) ≈ [C(CN)3](-) > [B(CN)4](-). On the other hand, no clear trend was observed for the viscosity of ILs and the respective number of -CN groups. The viscosity dependence on the cyano-functionalized anions decreases in the order: [SCN](-) > [B(CN)4](-) > [N(CN)2](-) > [C(CN)3](-). The isobaric thermal expansion coefficient, the derived molar refraction, the free volume, and the viscosity energy barrier of all compounds were estimated from the experimental data and are presented and discussed. Finally, group contribution models were applied, and new group contribution parameters are presented, extending these methods to the prediction of the ILs properties.

  15. Group contribution and parachor analysis of experimental data on density and surface tension for members of the homologous series of 1-C-n-3-methylimidazolium chlorides

    Czech Academy of Sciences Publication Activity Database

    Součková, Monika; Klomfar, Jaroslav; Pátek, Jaroslav

    2017-01-01

    Roč. 454, December (2017), s. 43-56 ISSN 0378-3812 R&D Projects: GA ČR GA13-00145S Institutional support: RVO:61388998 Keywords : ionic liquid * 1-alkyl-3-methylimidazolium-based cation * chloride anion * experimental data * density-temperature relation Subject RIV: BJ - Thermodynamics OBOR OECD: Thermodynamics Impact factor: 2.473, year: 2016

  16. Self-aggregation of bio-surfactants within ionic liquid 1-ethyl-3-methylimidazolium bromide: A comparative study and potential application in antidepressants drug aggregation

    Science.gov (United States)

    Banjare, Manoj Kumar; Behera, Kamalakanta; Kurrey, Ramsingh; Banjare, Ramesh Kumar; Satnami, Manmohan L.; Pandey, Siddharth; Ghosh, Kallol K.

    2018-06-01

    Aggregation behavior of bio-surfactants (BS) sodium cholate (NaC) and sodium deoxycholate (NaDC) within aqueous solution of ionic liquid (IL) 1-ethyl-3-methylimidazolium bromide [Emim][Br] has been investigated using surface tension, conductivity, steady state fluorescence, FT-IR and dynamic light scattering (DLS) techniques. Various interfacial and thermodynamic parameters are determined in the presence of different wt% of IL [Emim][Br]. Information regarding the local microenvironment and size of the aggregates is obtained from fluorescence and DLS, respectively. FT-IR spectral response is used to reveal the interactions taking place within aqueous NaC/NaDC micellar solutions. It is noteworthy to mention that increasing wt% of [Emim][Br] results in an increase in the spontaneity of micelle formation and the hydrophilic IL shows more affinity for NaC as compared to NaDC. Further, the micellar solutions of BS-[Emim][Br] are utilized for studying the aggregation of antidepressants drug promazine hydrochloride (pH). UV-vis spectroscopic investigation reveals interesting outcomes and the results show changes in spectral absorbance of PH drug on the addition of micellar solution (BS-[Emim][Br]). Highest binding affinity and most promising activity are shown for NaC as compared to NaDC.

  17. Identification of metabolites involved in the biodegradation of the ionic liquid 1-butyl-3-methylpyridinium bromide by activated sludge microorganisms.

    Science.gov (United States)

    Pham, Thi Phuong Thuy; Cho, Chul-Woong; Jeon, Che-Ok; Chung, Yun-Jo; Lee, Min-Woo; Yun, Yeoung-Sang

    2009-01-15

    Ionic liquids (ILs) are low melting organic salts that potentially comprise wide application due to their fascinating properties and have emerged as promising "green" replacements for volatile organic solvents. Despite their nonmeasurable vapor pressure, some quantities of ILs will soon be present in effluent discharges since they do have significant solubility in water. Recently, the toxic effects of ILs toward aquatic communities have been intensively investigated, but little information is available concerning the biodegradable properties of these compounds. The objective of this study was to identify the metabolites generated during the biotransformation of 1-butyl-3-methylpyridinium by microorganisms in aerobic activated sludge. The obtained results revealed that the alkylpyridinium salt was metabolized through the sequential oxidization in different positions of the alkyl side chains. High-performance liquid chromatography and mass-spectrometry analyses demonstrated that this biodegradation led to the formation of 1-hydroxybutyl-3-methylpyridinium, 1-(2-hydroxybutal)-3-methylpyridinium, 1-(2-hydroxyethyl)-3-methylpyridinium, and methylpyridine. On the basis of these intermediate products, biodegradation pathways were also suggested. These findings provide the basic information that might be useful for assessing the factors related to the environmental fate and behavior of this commonly used pyridinium IL.

  18. Effect of ionic liquids, 1-butyl-3-methyl imidazolium bromide and 1-hexyl-3-methyl imidazolium bromide on the vapour – Liquid equilibria of the aqueous D-fructose solutions at 298.15 K and atmospheric pressure using isopiestic method

    International Nuclear Information System (INIS)

    Zafarani-Moattar, Mohammed Taghi; Shekaari, Hemayat; Mazaher Haji Agha, Elnaz

    2017-01-01

    Highlights: • VLE data for aqueous fructose + [BMIm]Br or [HMIm]Br systems were measured. • Performances of different local composition models were tested in fitting VLE data. • Molal activity coefficients were calculated. • The results were discussed on basis of water, IL and sugar interactions. - Abstract: In this study, water activity measurements have been carried out by the isopiestic method for the systems (D-fructose + 1-butyl-3-methyl imidazolium bromide + H 2 O) and (D-fructose + 1-hexyl-3-methyl imidazolium bromide + H 2 O) at 298.15 K and atmospheric pressure. Vapour pressures and osmotic coefficients of the solutions have been determined from the experimental measured water activity results. The experimental water activity values were satisfactorily correlated with segment-based local composition models of the Wilson, NRTL, modified NRTL, NRF-NRTL and UNIQUAC. Then, using the parameters obtained from these models, the unsymmetrical molal activity coefficients of the D-fructose and ionic liquids in the binary and D-fructose in ternary aqueous solutions have been calculated. Furthermore, the activity coefficients of D-fructose in binary and ternary solutions were used to calculate the Gibbs energy of transfer for D-fructose from water to aqueous ionic liquid solutions. An application of McMillan-Mayer theory of solutions through virial expansion of transfer Gibbs energy was made to get pair and triplet interaction parameters and salting constant values. From the sign and magnitude of these parameters and salting constants and also from the magnitude of activity coefficients some information about solute-solute and solute-solvent interactions are obtained.

  19. Determination of Residual Nonsteroidal Anti-Inflammatory Drugs in Aqueous Sample Using Magnetic Nanoparticles Modified with Cetyltrimethylammonium Bromide by High Performance Liquid Chromatography

    OpenAIRE

    Khoeini Sharifabadi, Malihe; Saber-Tehrani, Mohammad; Waqif Husain, Syed; Mehdinia, Ali; Aberoomand-Azar, Parviz

    2014-01-01

    A simple and sensitive solid-phase extraction method for separation and preconcentration of trace amount of four nonsteroidal anti-inflammatory drugs (naproxen, indomethacin, diclofenac, and ibuprofen) using Fe3O4 magnetic nanoparticles modified with cetyltrimethylammonium bromide has been developed. For this purpose, the surface of MNPs was modified with cetyltrimethylammonium bromide (CTAB) as a cationic surfactant. Effects of different parameters influencing the extraction efficiency of dr...

  20. Ionic Liquid and Supercritical Fluid Hyphenated Techniques for Dissolution and Separation of Lanthanides, Actinides, and Fission Products

    International Nuclear Information System (INIS)

    Wai, Chien M.; Mincher, Bruce

    2012-01-01

    This project is investigating techniques involving ionic liquids (IL) and supercritical (SC) fluids for dissolution and separation of lanthanides, actinides, and fission products. The research project consists of the following tasks: Study direct dissolution of lanthanide oxides, uranium dioxide and other actinide oxides in [bmin][Tf 2 N] with TBP(HNO 3 ) 1.8 (H 2 O) 0.6 and similar types of Lewis acid-Lewis base complexing agents; Measure distributions of dissolved metal species between the IL and the sc-CO 2 phases under various temperature and pressure conditions; Investigate the chemistry of the dissolved metal species in both IL and sc-CO 2 phases using spectroscopic and chemical methods; Evaluate potential applications of the new extraction techniques for nuclear waste management and for other projects. Supercritical carbon dioxide (sc-CO 2 ) and ionic liquids are considered green solvents for chemical reactions and separations. Above the critical point, CO 2 has both gas- and liquid-like properties, making it capable of penetrating small pores of solids and dissolving organic compounds in the solid matrix. One application of sc-CO 2 extraction technology is nuclear waste management. Ionic liquids are low-melting salts composed of an organic cation and an anion of various forms, with unique properties making them attractive replacements for the volatile organic solvents traditionally used in liquid-liquid extraction processes. One type of room temperature ionic liquid (RTIL) based on the 1-alkyl-3-methylimidazolium cation [bmin] with bis(trifluoromethylsulfonyl)imide anion [Tf 2 N] is of particular interest for extraction of metal ions due to its water stability, relative low viscosity, high conductivity, and good electrochemical and thermal stability. Recent studies indicate that a coupled IL sc-CO 2 extraction system can effectively transfer trivalent lanthanide and uranyl ions from nitric acid solutions. Advantages of this technique include operation at

  1. Alkylation of nido-7,8-dicarbollide anion in liquid ammonia by propargyl bromide yielding 8-propargyl-nido-7,9-dicarbaundecaborate and 9-propargyl-nido-7,8-dicarbaundecaborate anions

    International Nuclear Information System (INIS)

    Zakharkin, L.I.; Ol'shevskaya, V.A.; Zhigareva, G.G.; Petrovskij, P.V.; Vinogradova, L.E.

    2002-01-01

    Products of alkylation of nido-7,8-dicarbollide anion by propargyl bromide in liquid ammonia at a temperature of -50 deg C were studied by the methods of 11 B NMR, IR and UV spectroscopy. It was ascertained that the above-mentioned reaction is accompanied by framework regroupings and results, depending on the reaction conditions, in formation of 8-propargyl-nido-7,9-dicarbaundecaborate- and 9-propargyl-nido-7,8-dicarbaundecaborate-anion. Ability of the salts prepared to get colored in alcohol solution as a result of action of diluted mineral acids, which is unusual for carborane derivatives, was revealed [ru

  2. Two Zn and Hg bromide salts based on 1-ethyl-3-methyl imidazolium ionic liquid: Ionothermal synthesis, structures and supramolecular organization

    Directory of Open Access Journals (Sweden)

    Xiu-Cheng Zhang

    2012-12-01

    Full Text Available Two Zn(II and Hg(II bromide salts, [EMI]2[ZnBr4] (1 and [EMI][HgBr3] (2, have been synthesized under ionothermal conditions using 1-ethyl-3-methyl imidazolium bromide ([EMI]Br as solvents. 1 consists of tetrahedral anion [ZnBr4]2− and 2 consists of 1D double chain locating in the cavities surrounded by [EMI]+ cations. Both compounds exhibit 3D supramolecular architectures organized by the C-H•••Br hydrogen bondings and alkyl-alkyl interactions.DOI: http://dx.doi.org/10.4314/bcse.v26i3.9

  3. Thermophysical properties of imidazolium tricyanomethanide ionic liquids: experiments and molecular simulation.

    Science.gov (United States)

    Zubeir, Lawien F; Rocha, Marisa A A; Vergadou, Niki; Weggemans, Wilko M A; Peristeras, Loukas D; Schulz, Peter S; Economou, Ioannis G; Kroon, Maaike C

    2016-08-17

    The low-viscous tricyanomethanide ([TCM](-))-based ionic liquids (ILs) are gaining increasing interest as attractive fluids for a variety of industrial applications. The thermophysical properties (density, viscosity, surface tension, electrical conductivity and self-diffusion coefficient) of the 1-alkyl-3-methylimidazolium tricyanomethanide [Cnmim][TCM] (n = 2, 4 and 6-8) IL series were experimentally measured over the temperature range from 288 to 363 K. Moreover, a classical force field optimized for the imidazolium-based [TCM](-) ILs was used to calculate their thermodynamic, structural and transport properties (density, surface tension, self-diffusion coefficients, viscosity) in the temperature range from 300 to 366 K. The predictions were directly compared against the experimental measurements. The effects of anion and alkyl chain length on the structure and thermophysical properties have been evaluated. In cyano-based ILs, the density decreases with increasing molar mass, in contrast to the behavior of the fluorinated anions, being in agreement with the literature. The contribution per -CH2- group to the increase of the viscosity presents the following sequence: [PF6](-) > [BF4](-) > [Tf2N](-) > [DCA](-) > [TCB](-) > [TCM](-). [TCM](-)-based ILs show lower viscosity than dicyanamide ([DCA](-))- and tetracyanoborate ([TCB](-))-based ILs, while the latter two exhibit a crossover which depends both on temperature and the alkyl chain length of the cation. The surface tension of the investigated ILs decreases with increasing alkyl chain length. [C2mim][TCM] shows an outlier behavior compared to other members of the homologous series. The surface enthalpies and surface entropies for all the studied systems have been calculated based on the experimentally determined surface tensions. The relationship between molar conductivity and viscosity was analyzed using the Walden rule. The experimentally determined self-diffusion coefficients of the cations are in good

  4. Methyl bromide residues in fumigated cocoa beans with particular reference to inorganic bromide

    International Nuclear Information System (INIS)

    Adomako, D.

    1976-01-01

    Inorganic bromide residues and 14 C-labelled methylated products (expressed as CH 3 Br equivalent) in cocoa beans fumigated with [ 14 C]-methyl bromide have been determined by radiometric and chemical methods. Determination of 14 C by direct combustion in an oxygen chamber followed by liquid scintillation counting confirmed previous findings with respect to the magnitude, distribution and chemical nature of the residues. Although recovery of added bromide was good, the values of total bromide obtained by the chemical method were only half of those estimated from the total residual 14 C-activity. This is attributed to loss of organic (presumably, protein-bound) bromide. In agreement with the total 14 C-labelled residue contents, total bromide in shells was 20 times greater than that in nibs. The low levels of residues in the nib (12ppm as CH 3 Br equivalent, 10ppm Br) and the further reduction of organic residues by roasting suggest that no toxicological and nutritional hazards may be expected from fumigation of cocoa beans with methyl bromide. (author)

  5. Aggregation behavior of gemini pyrrolidine-based ionic liquids 1,1'-(butane-1,4-diyl)bis(1-alkylpyrrolidinium) bromide ([C(n)py-4-C(n)py][Br2]) in aqueous solution.

    Science.gov (United States)

    Zhang, Shaohua; Yan, Han; Zhao, Mingwei; Zheng, Liqiang

    2012-04-15

    Three gemini pyrrolidine-based ionic liquids, 1,1'-(butane-1,4-diyl)bis(1-alkylpyrrolidinium) bromide ([C(n)py-4-C(n)py][Br(2)], n=10, 12, 14), were synthesized. Their aggregation behavior in aqueous solution was systematically investigated by surface tension, electrical conductivity, and steady-state fluorescence. Compared with their corresponding monomers, N-alkyl-N-methylpyrrolidinium bromide (C(n)MPB), [C(n)py-4-C(n)py][Br(2)], have higher surface activity. The special structure of [C(n)py-4-C(n)py][Br(2)] that has a spacer in their hydrophilic head groups results in a lower surface excess concentration (Γ(max)) and a larger molecular cross-sectional area (A(min)). Electrical conductivity studies show a lower degree of counter-ion binding to the aggregates. A smaller aggregation number (N(agg)) is observed by the pyrene fluorescence quenching method. A series of thermodynamic parameters (ΔG(agg)(0),ΔH(agg)(0),-TΔS(agg)(0)) of aggregation derived from electrical conductivity indicate that the aggregation of [C(n)py-4-C(n)py][Br(2)] is enthalpy-driven, while aggregation of C(n)MPB is entropy-driven at low temperatures but enthalpy-driven at high temperatures. Copyright © 2012 Elsevier Inc. All rights reserved.

  6. Determination of residual nonsteroidal anti-inflammatory drugs in aqueous sample using magnetic nanoparticles modified with cetyltrimethylammonium bromide by high performance liquid chromatography.

    Science.gov (United States)

    Khoeini Sharifabadi, Malihe; Saber-Tehrani, Mohammad; Waqif Husain, Syed; Mehdinia, Ali; Aberoomand-Azar, Parviz

    2014-01-01

    A simple and sensitive solid-phase extraction method for separation and preconcentration of trace amount of four nonsteroidal anti-inflammatory drugs (naproxen, indomethacin, diclofenac, and ibuprofen) using Fe3O4 magnetic nanoparticles modified with cetyltrimethylammonium bromide has been developed. For this purpose, the surface of MNPs was modified with cetyltrimethylammonium bromide (CTAB) as a cationic surfactant. Effects of different parameters influencing the extraction efficiency of drugs including the pH, amount of salt, shaking time, eluent type, the volume of solvent, amount of adsorbent, sample volume, and the time of desorption were investigated and optimized. Methanol has been used as desorption solvent and the extracts were analysed on a reversed-phase octadecyl silica column using 0.02 M phosphate-buffer (pH = 6.02) acetonitrile (65 : 35 v/v) as the mobile phase and the effluents were measured at 202 nm with ultraviolet detector. The relative standard deviation (RSD%) of the method was investigated at three concentrations (25, 50, and 200 ng/mL) and was in the range of 3.98-9.83% (n = 6) for 50 ng/mL. The calibration curves obtained for studied drugs show reasonable linearity (R (2) > 0.99) and the limit of detection (LODs) ranged between 2 and 7 ng/mL. Finally, the proposed method has been effectively employed in extraction and determination of the drugs in biological and environmental samples.

  7. Determination of Residual Nonsteroidal Anti-Inflammatory Drugs in Aqueous Sample Using Magnetic Nanoparticles Modified with Cetyltrimethylammonium Bromide by High Performance Liquid Chromatography

    Directory of Open Access Journals (Sweden)

    Malihe Khoeini Sharifabadi

    2014-01-01

    Full Text Available A simple and sensitive solid-phase extraction method for separation and preconcentration of trace amount of four nonsteroidal anti-inflammatory drugs (naproxen, indomethacin, diclofenac, and ibuprofen using Fe3O4 magnetic nanoparticles modified with cetyltrimethylammonium bromide has been developed. For this purpose, the surface of MNPs was modified with cetyltrimethylammonium bromide (CTAB as a cationic surfactant. Effects of different parameters influencing the extraction efficiency of drugs including the pH, amount of salt, shaking time, eluent type, the volume of solvent, amount of adsorbent, sample volume, and the time of desorption were investigated and optimized. Methanol has been used as desorption solvent and the extracts were analysed on a reversed-phase octadecyl silica column using 0.02 M phosphate-buffer (pH = 6.02 acetonitrile (65 : 35 v/v as the mobile phase and the effluents were measured at 202 nm with ultraviolet detector. The relative standard deviation (RSD% of the method was investigated at three concentrations (25, 50, and 200 ng/mL and was in the range of 3.98–9.83% (n=6 for 50 ng/mL. The calibration curves obtained for studied drugs show reasonable linearity (R2>0.99 and the limit of detection (LODs ranged between 2 and 7 ng/mL. Finally, the proposed method has been effectively employed in extraction and determination of the drugs in biological and environmental samples.

  8. Quality evaluation of Hypericum ascyron extract by two-dimensional high-performance liquid chromatography coupled with the colorimetric 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide method.

    Science.gov (United States)

    Li, Xiu-Mei; Luo, Xue-Gang; Zhang, Chao-Zheng; Wang, Nan; Zhang, Tong-Cun

    2015-02-01

    In this paper, a heart-cutting two-dimensional high-performance liquid chromatography coupled with the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) method was established for controlling the quality of different batches of Hypericum ascyron extract for the first time. In comparison with the common one-dimensional fingerprint, the second-dimensional fingerprint compiled additional spectral data and was hence more informative. The quality of H. ascyron extract was further evaluated by similarity measures and the same results were achieved, the correlation coefficients of the similarity of ten batches of H. ascyron extract were >0.99. Furthermore, we also evaluated the quality of the ten batches of H. ascyron extract by antibacterial activity. The result demonstrated that the quality of the ten batches of H. ascyron extract was not significantly different by MTT. Finally, we demonstrated that the second-dimensional fingerprint coupled with the MTT method was a more powerful tool to characterize the quality of samples of batch to batch. Therefore the proposed method could be used to comprehensively conduct the quality control of traditional Chinese medicines. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Methylnaltrexone bromide methanol monosolvate

    Directory of Open Access Journals (Sweden)

    Xinbo Zhou

    2012-03-01

    Full Text Available In the title compound [systematic name: (4R,4aS,7aR,12bS-3-cyclopropylmethyl-4a,9-hydroxy-7-oxo-2,3,4,4a,5,6,7,7a-octahydro-1H-4,12-methanobenzofuro[3,2-e]isoquinolin-3-ium bromide methanol monosolvate], C21H26NO4+·Br−·CH3OH, two of the three six-membered rings adopt chair conformations while the third, which contains a C=C double bond, adopts an approximate half-boat conformation. The 2,3-dihydrofuran ring adopts an envelope conformation. In the crystal, the components are linked by O—H...O and O—H...Br hydrogen bonds. The absolute stereochemistry was inferred from one of the starting materials.

  10. Iron bromide vapor laser

    Science.gov (United States)

    Sukhanov, V. B.; Shiyanov, D. V.; Trigub, M. V.; Dimaki, V. A.; Evtushenko, G. S.

    2016-03-01

    We have studied the characteristics of a pulsed gas-discharge laser on iron bromide vapor generating radiation with a wavelength of 452.9 nm at a pulse repetition frequency (PRF) of 5-30 kHz. The maximum output power amounted to 10 mW at a PRF within 5-15 kHz for a voltage of 20-25 kV applied to electrodes of the discharge tube. Addition of HBr to the medium produced leveling of the radial profile of emission. Initial weak lasing at a wavelength of 868.9 nm was observed for the first time, which ceased with buildup of the main 452.9-nm line.

  11. Bromide in some coastal and oceanic waters of India

    Digital Repository Service at National Institute of Oceanography (India)

    DeSouza, F.P.; Dalal, V.N.K.

    Bromide concentration and bromide/chlorinity ratio are estimated in coastal waters of Goa, Minicoy Lagoon, Western Arabian Sea and Western Bay of Bengal. The influence of precipitation and river runoff on bromide and bromide/chlorinity ratio...

  12. Uptake of ozone to mixed sodium bromide/ citric acid solutions

    Science.gov (United States)

    Lee, Ming-Tao; Steimle, Emilie; Bartels-Rausch, Thorsten; Kato, Shunsuke; Lampimäki, Markus; Brown, Matthew; van Bokhoven, Jeroen; Nolting, Frithjof; Kleibert, Armin; Türler, Andreas; Ammann, Markus

    2013-04-01

    headgroup [5]. In this study we would like to go one step further and look into the effect of a more complex organic compound, CA. We used ambient pressure XPS on a vacuum liquid microjet. The continuously refreshed free-flowing aqueous filament under vacuum permits photoelectron spectroscopy measurements from volatile aqueous interfaces in absence of beam damage [6]. Measurements were made at the SIM beam line of the Swiss Light Source (SLS) at the Paul Scherrer Institute. The ability to tune the photon energy (150-2000 eV) is crucial to get precise component ratios as a function of photoelectron kinetic energy and thus probe depth, thus allowing to determine relative concentrations of citric acid and bromide at the surface and in the bulk, respectively. REFERENCES [1] Clifford and Donaldson, J. Phys. Chem. A, 111, 9809-9814, (2007). [2] Oldridge and Abbatt, J. Phys. Chem. A, 115, 2590-2598, (2011). [3] S. Ghosal et al., Science 307, 563 (2005). [4] M.A. Brown et al., Phys. Chem. Chem. Phys. 10, 4778 (2008). [5] M. Krisch et al., J. Phys. Chem. C 111, 13497 (2007). [6] M.A. Brown et al., J. Phys. Chem. Lett. 3, 231 (2012).

  13. System of lithium, sodium, and strontium bromides

    International Nuclear Information System (INIS)

    Litvinova, G.N.; Yagub'yan, E.S.; Bukhalova, G.A.

    1988-01-01

    The visual-polythermal and partially differential thermal methods of analysis have been applied to investigate the meltability diagram of the Li 2 Br 2 -Na 2 Br 2 -SrBr 2 ternary system. Three fields of crystallization belonging to strontium bromide, to the compound LiSr 2 Br 5 and solid solutions of lithium and sodium bromides are found. Two points complying with nonvariant equilibria are discovered

  14. Silica coated ionic liquid templated mesoporous silica nanoparticles ...

    African Journals Online (AJOL)

    A series of long chain pyridinium based ionic liquids 1-tetradecylpyridinium bromide, 1-hexadecylpyridinium bromide and 1-1-octadecylpyridinium bromide were used as templates to prepare silica coated mesoporous silica nanoparticles via condensation method under basic condition. The effects of alkyl chain length on ...

  15. Effect of ipratropium bromide in bronchial asthma.

    Directory of Open Access Journals (Sweden)

    Taskar V

    1992-07-01

    Full Text Available The effect of inhalation of ipratropium bromide was evaluated in 20 patients with bronchial asthma. It was observed that there was no significant improvement in the forced vital capacity and the forced expired volume in one second, while there was significant improvement in the peak expiratory flow rate (PEFR measured at 9 pm, after inhalation of 2 puffs of ipratropium bromide aerosol (0.02mg/puff three to four times a day for 2 weeks. Since PEFR is a measure of large airway function and cholinergic mechanisms are primarily involved for airflow obstruction at large airways, improvement in PEFR by ipratropium bromide highlights its role as a useful bronchodilator in patients in whom vagal reflexes are responsible for the provocation of bronchoconstriction.

  16. A novel cetyltrimethyl ammonium silver bromide complex and silver bromide nanoparticles obtained by the surfactant counterion.

    Science.gov (United States)

    Liu, Xian-Hao; Luo, Xiao-Hong; Lu, Shu-Xia; Zhang, Jing-Chang; Cao, Wei-Liang

    2007-03-01

    A novel cetyltrimethyl ammonium silver bromide (CTASB) complex has been prepared simply through the reaction of silver nitrate with cetyltrimethyl ammonium bromide (CTAB) in aqueous solution at room temperature by controlling the concentration of CTAB and the molar ratio of CTAB to silver nitrate in the reaction solution, in which halogen in CTAB is used as surfactant counterion. The structure and thermal behavior of cetyltrimethyl ammonium silver bromide have been investigated by using X-ray diffraction (XRD), infrared spectroscopy (IR), X-ray photoelectron spectroscopy (XPS), UV/vis spectroscopy, thermal analysis (TG-DTA), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The results show that the complex possesses a metastable layered structure. Upon heating the CTASB aqueous dispersion to above 80 degrees C, the structure change of the complex took place and CTAB-capped nanosized silver bromide particles further formed.

  17. 40 CFR 180.123 - Inorganic bromide residues resulting from fumigation with methyl bromide; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ..., postharvest 30.0 Lemon, postharvest 30.0 Lime, postharvest 30.0 Mango, postharvest 20.0 Melon, honeydew... methyl bromide or from such fumigation in addition to the authorized use of methyl bromide on the source...

  18. Radiolytic reduction reaction of colloidal silver bromide solution

    International Nuclear Information System (INIS)

    Oya, Yasuhisa; Zushi, Takehiro; Hasegawa, Kunihiko; Matsuura, Tatsuo.

    1995-01-01

    The reduction reaction of colloidal silver bromide (AgBr 3 ) 2- in nitrous oxide gas saturated solution of some alcohols: methanol, ethanol, 2-propanol and 2-methyl-2-propanol by γ-irradiation was studied spectrophotometrically in order to elucidate the mechanism of the formation of colloidal silver bromide (AgBr 3 ) 3- at ambient temperature. The amount of colloidal silver bromide formed increases in the order: i-PrOH, EtOH, MeOH. In t-BuOH, colloidal silver bromide did not form. The relative reactivities of alcohols for colloidal silver bromide was also studied kinetically. (author)

  19. Methyl bromide residues in fumigated cocoa beans

    International Nuclear Information System (INIS)

    Adomako, D.

    1975-01-01

    The 14 C activity in unroasted [ 14 C]-methyl bromide fumigated cocoa beans was used to study the fate and persistence of CH 3 Br in the stored beans. About 70% of the residues occurred in the shells. Unchanged CH 3 Br could not be detected, all the sorbed CH 3 Br having reacted with bean constituents apparently to form 14 C-methylated derivatives and inorganic bromide. No 14 C activity was found in the lipid fraction. Roasting decreased the bound (non-volatile) residues, with corresponding changes in the activities and amounts of free sugars, free and protein amino acids. Roasted nibs and shells showed a two-fold increase in the volatile fraction of the 14 C residue. This fraction may be related to the volatile aroma compounds formed by Maillard-type reactions. (author)

  20. First Stabilization and Disposal of Radioactive Zinc Bromide at the SRS

    International Nuclear Information System (INIS)

    Denny, J.K.

    2003-01-01

    Facilities Disposition Projects (FDP) personnel at Savannah River Site (SRS) implement the Inactive Facility Risk Management Program to drive down risk and costs in SRS inactive facilities. The program includes cost-effective techniques to identify and dispose of hazardous chemicals and radioactive waste from inactive facilities, thereby ensuring adequate protection of the public, workers and the environment. In June 1998, FDP conducted an assessment of the inactive C-Reactor Facility to assure that chemical and radiological hazards had been identified and were being safely managed. The walkdown identified the need to mitigate a significant hazard associated with storing approximately 13,400 gallons of liquid radioactive Zinc Bromide in three aging railcar tankers outside of the facility. No preventive maintenance was being performed on the rusting tankers and a leak could send radioactive Zinc Bromide into an outfall and offsite to the Savannah River. In 2001, DOE-Savannah River (DOE- SR) funded the FDP to eliminate the identified hazard by disposing of the radioactive Zinc Bromide solution and the three contaminated railcar tankers. This paper describes the innovative, cost-effective approaches and technology used to perform the first stabilization and disposal of radioactive Zinc Bromide at SRS

  1. Advanced hydrogen electrode for hydrogen-bromide battery

    Science.gov (United States)

    Kosek, Jack A.; Laconti, Anthony B.

    1987-01-01

    Binary platinum alloys are being developed as hydrogen electrocatalysts for use in a hydrogen bromide battery system. These alloys were varied in terms of alloy component mole ratio and heat treatment temperature. Electrocatalyst evaluation, performed in the absence and presence of bromide ion, includes floating half cell polarization studies, electrochemical surface area measurements, X ray diffraction analysis, scanning electron microscopy analysis and corrosion measurements. Results obtained to date indicate a platinum rich alloy has the best tolerance to bromide ion poisoning.

  2. Studies on chlorinated bromide salt for microfouling control

    International Nuclear Information System (INIS)

    Satpathy, K.K.; Rajmohan, R.; Rao, T.S.; Nair, K.V.K.; Mathur, P.K.

    1995-01-01

    The Fast Breeder Test reactor (FBTR) at Kalpakkam has been facing various problems in cooling water systems in spite of intermittent chlorination.Effects of chlorinated-bromide mixture was evaluated against heterotrophic bacteria (TVC) and iron oxidising bacteria (IOB) vis-a-vis chlorine. Results indicated that chlorinated-bromide mixture was far superior (2 orders of magnitude for TVC and 2 times for IOB) to chlorine in microfouling control. Results also showed that at bromide to chlorine ratio of one effectiveness of chlorinated-bromide was at its maximum. (author). 9 refs., 1 tab

  3. Development of copper bromide laser master oscillator power

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... Development of master oscillator power amplifier (MOPA) system of copper bromide laser (CBL) operating at 110 W average power is reported. The spectral distribution of power at green (510.6 nm) and yellow (578.2 nm) components in the output of a copper bromide laser is studied as a function of ...

  4. Conduction bands and invariant energy gaps in alkali bromides

    NARCIS (Netherlands)

    Boer, P.K. de; Groot, R.A. de

    1998-01-01

    Electronic structure calculations of the alkali bromides LiBr, NaBr, KBr, RbBr and CsBr are reported. It is shown that the conduction band has primarily bromine character. The size of the band gaps of bromides and alkali halides in general is reinterpreted.

  5. Ion adsorption properties of molybdenum (II) bromide

    International Nuclear Information System (INIS)

    Ganzerli-Valentini, M.T.; Meloni, S.; Caramella-Crespi, V.; Borroni, P.A.

    1976-01-01

    The adsorption of about 50 ions on molybdenum dibromide, (Mo 6 Br 8 )Br 4 .2H 2 O in nitric acid was investigated. The behaviour of the investigated elements on MDB in nitric acid, in the concentration range 10 -2 -8M is presented, where the distribution coefficients are given against the HNO 3 molarity. In some cases the elements were investigated in different oxidation states. Most of the elements are not adsorbed or poorly adsorbed, among these the stable anions, thus indicating that bromide ions substitution with other anions is not competitive. The preparation of the adsorber and its characterization is presented and discussed. Adsorption mechanism studies were carried out for some noble metals and chromium. Sorption cannot be ascribed to ion exchange mechanism but to formation of insoluble species, and to settlement of few ions into surface sorption sites or into a limited number of cavitites in the cluster crystal structure of the adsorber. (T.G.)

  6. Agricultural soil fumigation as a source of atmospheric methyl bromide.

    Science.gov (United States)

    Yagi, K; Williams, J; Wang, N Y; Cicerone, R J

    1993-09-15

    Methyl bromide (MeBr) is used increasingly as a biocidal fumigant, primarily in agricultural soils prior to planting of crops. This usage carries potential for stratospheric ozone reduction due to Br atom catalysis, depending on how much MeBr escapes from fumigated soils to the atmosphere and on details of atmospheric chemical reactions. We present direct field measurements of MeBr escape; 87% of the applied MeBr was emitted within 7 days after a commercial fumigation. Covering the field with plastic sheets retarded MeBr escape somewhat but first-day losses were still 40%; thicker sections of sheets were relatively more effective than thin sections. We also measured gaseous MeBr concentrations versus depth in the soil column; these profiles display diffusion-like evolution. In soil, MeBr is partitioned among gas, liquid, and adsorbed solid phases. Calculated soil inventories agreed only roughly with applied amounts, probably due to nonequilibrium partitioning (during the first 30 min) and to uncertainties in partitioning coefficients. Fumigated fields may release less MeBr if they are covered by more gas-tight plastic films, if injection techniques are improved and injection is deeper, and if soil moistures, organic amounts, and densities are greater than in the soil studied here.

  7. Alkene- and alkyne- substituted methylimidazolium bromides: structural effects and Physical properties (Postprint)

    National Research Council Canada - National Science Library

    Schneider, Stefan; Drake, Gregory; Hall, Leslie; Hawkiins, Tommy; Rosander, Michael; Smith, Dennis

    2007-01-01

    .... X-ray structures of 1-(2-butynyl)-3-methylimidazolium bromide, 1-propargyl-3-methylimidazolium bromide as well as the X-ray structure of 1-allyl-3- methylimidazolium bromide which was previously identified as a room temperature ionic...

  8. Alkene- and Alkyne- Substituted Methylimidazolium Bromides: Structural Effects and Physical properties (Preprint)

    National Research Council Canada - National Science Library

    Schneider, Stefan; Drake, Gregory; Hall, Leslie; Hawkiins, Tommy; Rosander, Michael; Smith, Dennis

    2007-01-01

    .... X-ray structures of 1-(2-butynyl)-3-methylimidazolium bromide, 1-propargyl-3-methylimidazolium bromide as well as the X-ray structure of 1-allyl-3- methylimidazolium bromide which was previously identified as a room temperature ionic...

  9. Trends in bromide wet deposition concentrations in the contiguous United States, 2001-2016.

    Science.gov (United States)

    Wetherbee, Gregory A; Lehmann, Christopher M B; Kerschner, Brian M; Ludtke, Amy S; Green, Lee A; Rhodes, Mark F

    2018-02-01

    Bromide (Br - ) and other solute concentration data from wet deposition samples collected and analyzed by the National Atmospheric Deposition Program (NADP) from 2001 to 2016, were statistically analyzed for trends both geographically and temporally by precipitation type. Analysis was limited to NADP sites in the contiguous 48 United States. The Br - concentrations for this time period had a high number of values censored at the detection limits with greater than 86 percent of sample concentrations below analytical detection. Bromide was more frequently detected at NADP sites in coastal regions. Analysis using specialized statistical techniques for censored data revealed that Br - concentrations varied by precipitation type with higher concentrations usually observed in liquid versus precipitation containing snow. Negative temporal trends in Br - wet deposition concentrations were observed at a majority of NADP sites; approximately 25 percent of these trend values were statistically significant at less than 0.05 to 0.10 significance levels. Potential causes for the negative trends were explored, including annual and seasonal changes in precipitation depth, reduced emissions of methyl bromide (CH 3 Br) from coastal wetlands, and declining industrial use of bromine compounds. The results indicate that Br - in non-coastal wet-deposition comes mainly from long-range transport, not local sources. Correlations between Br - , chloride, and nitrate concentrations also were evaluated. Published by Elsevier Ltd.

  10. Isopiestic investigation of the osmotic coefficients of MgBr{sub 2}(aq) and study of bromide salts solubility in the (m{sub 1}KBr + m{sub 2}MgBr{sub 2})(aq) system at T = 323.15 K. Thermodynamic model of solution behaviour and (solid + liquid) equilibria in the MgBr{sub 2}(aq), and (m{sub 1}KBr + m{sub 2}MgBr{sub 2})(aq) systems to high concentration and temperature

    Energy Technology Data Exchange (ETDEWEB)

    Christov, Christomir, E-mail: christov@svr.igic.bas.b [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, ul. ' Acad. G. Bonchev' , bl. 11, 1113 Sofia (Bulgaria)

    2011-03-15

    The isopiestic method has been used to determine the osmotic coefficients of the binary solutions MgBr{sub 2}(aq) (from 0.4950 to 2.5197 mol {center_dot} kg{sup -1}) at the temperature T = 323.15 K. Sodium chloride solutions have been used as isopiestic reference standards. The solubility of the bromide minerals in the mixed system (m{sub 1}KBr + m{sub 2}MgBr{sub 2})(aq) has been investigated at T = 323.15 K by the physico-chemical analysis method. In addition to simple salts {l_brace}KBr(cr) and MgBr{sub 2} . 6H{sub 2}O(cr){r_brace}, equilibrium crystallization of the highly incongruent double salt with stoichiometric composition 1:1:6 {l_brace}bromcarnallite: KBr . MgBr{sub 2} . 6H{sub 2}O(cr){r_brace} was also established. The results obtained from the isopiestic and solubility measurements have been combined with all other experimental thermodynamic quantities available in the literature (osmotic coefficients, and solubility of the bromide mineral) to construct a chemical model that calculates solute and solvent activities and (solid + liquid) equilibria in the MgBr{sub 2}(aq) binary, and (m{sub 1}KBr + m{sub 2}MgBr{sub 2})(aq) mixed systems from dilute to high solution concentration within the (273.15 to 438.15) K temperature range. The solubility modelling approach based on fundamental Pitzer specific interaction equations is employed. It was found, that the standard for 2-1 type of electrolytes approach with three ({beta}{sup (0)}, {beta}{sup (1)}, and C{sup {phi}}) single electrolyte ion interaction parameters gives excellent agreement with osmotic coefficients from T = (298.15 to 373.45) K; up to saturation at 298.15 K, and up to m(MgBr{sub 2}) = 5.83 mol {center_dot} kg{sup -1} at 373.45 K, and with MgBr{sub 2} {center_dot} 6H{sub 2}O(cr) equilibrium pure water solubility data within the (273.15 to 438.15) K temperature range and up to {approx}8.5 mol {center_dot} kg{sup -1} used in parameterization. The model for the ternary system gives very good

  11. Spectroscopic investigations of Eu{sup 3+}-complexes with ligands containing multiple diglycolamide pendant arms in a room temperature ionic liquid

    Energy Technology Data Exchange (ETDEWEB)

    Sengupta, Arijit [Radiochemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Mohapatra, Prasanta K., E-mail: mpatra@barc.gov.in [Radiochemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Iqbal, Mudassir; Huskens, Jurriaan; Verboom, Willem [Laboratory of Molecular Nanofabrication, MESA" + Institute for Nanotechnology, University of Twente, P. O. Box 217, 7500 AE Enschede (Netherlands)

    2014-10-15

    Fluorescence spectroscopy was used to study the complexation of different ligands containing multiple diglycolamide (DGA) pendent arms such as T-DGA (tripodal diglycolamide), C4DGA (upper rim functionalized calix [4] arene with four DGA moieties), and C8DGA (both side functionalized calix [4] arene with eight DGA moieties) with Eu{sup 3+} in ionic liquids such as C{sub 4}mimNTf{sub 2} and C{sub 8}mimNTf{sub 2} (1-alkyl-3-methylimidazolium bis(trifluoromethylsulphonyl)imide). Mainly five sets of emission profiles were observed in all the spectra (1st set at∼580 nm assigned as the {sup 5}D{sub 0}→{sup 7}F{sub 0} transition, 2nd set at∼593 nm assigned as the {sup 5}D{sub 0}→{sup 7}F{sub 1} transition, 3rd set at∼613 nm assigned as the {sup 5}D{sub 0}→{sup 7}F{sub 2} transition, 4th set at∼650 nm assigned as the {sup 5}D{sub 0}→{sup 7}F{sub 3} transition, and 5th set at∼700 nm assigned as the {sup 5}D{sub 0}→{sup 7}F{sub 4} transition). The difference in the spectral features revealed that the nature of the complexes differs significantly from one another. Judd–Offelt constant Ω{sub 2}, which is a measure of the covalency of the metal–ligand bond, follows the order Eu{sup 3+}–C4DGA (C{sub 8}mimNTf{sub 2})>Eu{sup 3+}–C8DGA (C{sub 8}mimNTf{sub 2})>Eu{sup 3+}–TODGA (C{sub 4}mimNTf{sub 2})>Eu{sup 3+}–T-DGA (C{sub 4}mimNTf{sub 2})>Eu{sup 3+}{sub aq}. The high intensity of the {sup 5}D{sub 0}→{sup 7}F{sub 2} transitions in all complexes suggests that Eu{sup 3+} resides in a highly asymmetric environment. From the splitting patterns of the transitions, the local site symmetry around Eu{sup 3+} was found to be C{sub 2V} for the Eu{sup 3+}–T-DGA complex in both C{sub 4}mimNTf{sub 2} and a 1:5 acetonitrile–water mixture, C{sub 4V} for Eu{sup 3+}–C8DGA and Eu{sup 3+}–TODGA complexes, and either C{sub 1}, C{sub 2}, or C{sub S} for the Eu{sup 3+}–C4DGA complex. A linear relationship between the {sup 5}D{sub 0}–{sup 7}F{sub 1} splitting

  12. Chloride, bromide and iodide scintillators with europium

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2016-09-27

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  13. Growth and Characterization of Tetraphenylphosphonium Bromide Crystal

    Directory of Open Access Journals (Sweden)

    Guangqiang Wang

    2017-05-01

    Full Text Available Multiple-phenyl phosphorous compounds are a group of chemical materials that have been used as reactants, pharmaceutical intermediates, extractants, and catalysts in organic synthetic reactions. However, the crystal growth of bulk crystals of multiple-phenyl phosphorous compounds, which may expand their applications in photonics technology, have been largely overlooked. In this article, the crystal growth of tetraphenylphosphonium bromide (TPPB has been studied in organic solvents and water. The crystal structures and crystallization features are analyzed by X-ray diffraction data. By a slow temperature-lowering method, a single-crystal of TPPB (2H2O with the size of 27 × 20 × 20 mm3 has been obtained in water. The basic thermal and optical properties were characterized. We find that the TPPB (2H2O crystal shows excellent transparent property in the near-IR region. Large Raman shifts and strong Raman scattering intensity indicate that TPPB is a potential candidate in Raman-scattering-based nonlinearity applications.

  14. Bromide space, total body water, and sick cell syndrome

    International Nuclear Information System (INIS)

    Schober, O.; Hundeshagen, H.; Lehr, L.

    1982-01-01

    Displacements of the bromide space (Br-82-C, as a marker for the extracellular fluid compartment) are caused by an enhanced anatomical space and/or increased permeability of cells to bromide. The ratio Br-82-C: total body water (TBW) was evaluated to be 0.83 +- 0.17 in critically ill patients (n = 38) compared with the normal value of 0.46 +- 0.04 (n = 10). Because of normal TBW in critically ill patients (TBW = 505 +- 68 ml/kg), an increased bromide penetration into cells seems to be responsible for the enlarged ratio Br-82-C: TBW. Taking into consideration measurements in patients with malabsorption (Br-82-C: TBW = 0.56 +- 0.13; n = 13) and carcinoma of the rectum and colon (Br-82-C: TBW = 0.66 +- 0.24; n = 18) we think that the bromide space is a good measurement of the effective extracellular water. (orig.)

  15. Development of copper bromide laser master oscillator power ...

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... Development of master oscillator power amplifier (MOPA) system of copper bromide laser (CBL) operating at ... The spectral distribution of power at .... It is evident from the voltage waveforms that the breakdown voltage drops.

  16. Methyl Bromide Commodity Fumigation Buffer Zone Lookup Tables

    Science.gov (United States)

    Product labels for methyl bromide used in commodity and structural fumigation include requirements for buffer zones around treated areas. The information on this page will allow you to find the appropriate buffer zone for your planned application.

  17. Synthesis and Heme Polymerization Inhibitory Activity (HPIA Assay of Antiplasmodium of (1-N-(3,4-Dimethoxybenzyl-1,10-Phenanthrolinium Bromide from Vanillin

    Directory of Open Access Journals (Sweden)

    Dhina Fitriastuti

    2014-03-01

    Full Text Available The synthesis of (1-N-(3,4-dimethoxy-benzyl-1,10-phenanthrolinium bromide had been conducted from vanillin. Heme polymerization inhibitory activity assay of the synthesized antiplasmodium has also been carried out. The first step of reaction was methylation of vanillin using dimethylsulfate and NaOH. The mixture was refluxed for 2 h to yield veratraldehyde in the form of light yellow solid (79% yield. Methylation product was reduced using sodium borohydride (NaBH4 with grinding method and yielded veratryl alcohol in the form of yellow liquid (98% yield. Veratryl alcohol was brominated using PBr3 to yield yellowish black liquid (85% yield. The final step was benzylation of 1,10-phenanthroline monohydrate with the synthesized veratryl bromide under reflux condition in acetone for 14 h to afford (1-N-(3,4-dimethoxy-benzyl-1,10-phenanthrolinium bromide (84% as yellow solid with melting point of 166-177 °C. The structures of products were characterized by FT-IR, GC-MS and 1H-NMR spectrometers. The results of heme polymerization inhibitory activity assay of (1-N-(3,4-dimethoxybenzyl-1,10-phenanthrolinium bromide showed that it had IC50 HPIA of 3.63 mM, while chloroquine had IC50 of4.37 mM. These results indicated that (1-N-(3,4-dimethoxybenzyl-1,10-phenanthrolinium bromide was more potential antiplasmodium than chloroquine.

  18. Fluoride, bromide and iodide in the Arabian Sea

    Digital Repository Service at National Institute of Oceanography (India)

    DeSouza, F.P.

    Fluoride concentrations varying from 1.32 mg/l at the surface to 1.37 mg/l at depth showed an average of 1.35 + or - 0.004 mg/l with F/Cl of (6.65 + - 0.07) x 10/5. Average bromide was 70 mg/l with Br/Cl of 0.00347. Bromide was found to bear a...

  19. Disinfection byproduct regulatory compliance surrogates and bromide-associated risk.

    Science.gov (United States)

    Kolb, Chelsea; Francis, Royce A; VanBriesen, Jeanne M

    2017-08-01

    Natural and anthropogenic factors can alter bromide concentrations in drinking water sources. Increasing source water bromide concentrations increases the formation and alters the speciation of disinfection byproducts (DBPs) formed during drinking water treatment. Brominated DBPs are more toxic than their chlorinated analogs, and thus have a greater impact on human health. However, DBPs are regulated based on the mass sum of DBPs within a given class (e.g., trihalomethanes and haloacetic acids), not based on species-specific risk or extent of bromine incorporation. The regulated surrogate measures are intended to protect against not only the species they directly represent, but also against unregulated DBPs that are not routinely measured. Surrogates that do not incorporate effects of increasing bromide may not adequately capture human health risk associated with drinking water when source water bromide is elevated. The present study analyzes trihalomethanes (THMs), measured as TTHM, with varying source water bromide concentrations, and assesses its correlation with brominated THM, TTHM risk and species-specific THM concentrations and associated risk. Alternative potential surrogates are evaluated to assess their ability to capture THM risk under different source water bromide concentration conditions. The results of the present study indicate that TTHM does not adequately capture risk of the regulated species when source water bromide concentrations are elevated, and thus would also likely be an inadequate surrogate for many unregulated brominated species. Alternative surrogate measures, including THM 3 and the bromodichloromethane concentration, are more robust surrogates for species-specific THM risk at varying source water bromide concentrations. Copyright © 2017. Published by Elsevier B.V.

  20. On-line production of [11C]cyanogen bromide

    International Nuclear Information System (INIS)

    Westerberg, G.; Laangstroem, B.

    1997-01-01

    The electrophilic labelling precursor [ 11 C]cyanogen bromide was produced in 95% radiochemical yield (decay-corrected) from hydrogen [ 11 C]cyanide within 3 min from the end of bombardment using a simple and convenient solid-phase on-line procedure. The [ 11 C]cyanogen bromide has been used in the synthesis of a number of labelled compounds for use in positron emission tomography. (author)

  1. Interaction of cephalosporin drugs with dodecyltrimethylammonium Bromide

    International Nuclear Information System (INIS)

    Hoque, Md. Anamul; Hossain, Mohammed Delwar; Khan, Mohammed Abdullah

    2013-01-01

    Highlights: • We carry out the interaction of cephalosporin drugs with DTAB conductometrically. • We examine the effect of drugs on the critical micelle concentration of DTAB. • Three critical micelle concentrations are obtained for drug- DTAB system. • Electrostatic and hydrophobic interactions between drugs and DTAB are proposed. • Drug supported micelle formation of DTAB is much favoured in aq. solution of K 2 SO 4 . -- Abstract: The interaction of three cephalosporin drugs namely cefadroxyl monohydrate (CFM), cephalexin monohydrate (CLM) and cephradine monohydrate (CDM) with dodecyltrimethylammonium Bromide (DTAB) has been carried out by conductance measurements in aqueous medium and in aqueous solution of K 2 SO 4 salt over temperature range of (303.15 to 318.15) K. For pure DTAB and drug-DTAB systems, three critical micelle concentrations were obtained. The third critical micelle concentration (c ∗ 3 ) indicates that the spherical micelle turns into rod shape that is sphere to rod transition. The c ∗ values of DTAB are changed due to the addition of cephalosporin drugs. In addition, the change of the values of c ∗ 1 , c ∗ 2 and c ∗ 3 with increase of the concentration of drugs indicate the presence of interaction between drug and DTAB. The c ∗ values indicate that micellization for the cephalosporins-surfactant systems in water follow the order: CFM-surfactant ∗ values for the cephalosporins - DTAB systems in aqueous K 2 SO 4 are lower in magnitude than those in pure water and the values decrease with increase of the concentrations of K 2 SO 4 at a particular temperature. A significant decrease of c ∗ values in the presence of K 2 SO 4 for cephalosporins-DTAB systems indicates that drug supported ionic micelle formation is much favoured in aqueous K 2 SO 4 solution compared to that in pure water. For cephalosporin-DTAB systems, ΔG 0 m values are negative which indicate that the drugs mediated ionic micelle formation processes are

  2. Thermodynamics of the interactions of some amino acids and peptides with dodecyltrimethylammonium bromide and tetradecyltrimethylammonium bromide

    International Nuclear Information System (INIS)

    Talele, Paurnima; Kishore, Nand

    2014-01-01

    Highlights: • Interactions of amino acids and peptides were studied with two cationic surfactants. • Partial molar properties and hydration numbers did not change significantly. • Measured properties indicate balance of polar and non-polar interactions. • Peptide bonds did not strengthen the extent of polar interactions with surfactant. • Results provide quantitative fine details of cationic surfactant–amino acids/peptides interactions. -- Abstract: The values of apparent molar volume V 2,ϕ and apparent molar adiabatic compressibility K S,2,ϕ of amino acids glycine, L-alanine, DL-α-amino-n-butyric acid, L-valine, L-leucine and peptides glycyl-glycine, glycyl-glycyl-glycine and glycyl-leucine have been determined in aqueous solutions of cationic surfactants dodecyltrimethylammonium bromide (DTAB) and tetradecyltrimethylammonium bromide (TTAB) by means of density and sound velocity measurements. The heat evolved or absorbed (q) during the course of interactions of amino acids and peptides with the aqueous solutions of surfactants were determined by isothermal titration calorimetry at T = 298.15 K. The values of standard partial molar volume V 2,m 0 and standard partial molar adiabatic compressibility K s,2,m 0 at infinite dilution were calculated from the values of V 2,ϕ and K S,2,ϕ . Similarly the values of limiting enthalpies of dilution (Δ dil H 0 ) of the amino acids/peptides were calculated from heat evolved or absorbed during calorimetric experiments. The standard partial molar quantities of transfer from water to aqueous surfactant solutions have been used to identify the interactions of amino acids and peptides with surfactants in terms of ionic–ionic, ionic–hydrophobic and hydrophobic–hydrophobic group interactions

  3. Dilute Ionic Liquids Pretreatment of Palm Empty Bunch and Its Impact to Produce Bioethanol

    OpenAIRE

    Lucy Arianie; Utin Dewi Pebriyana; Yudiansyah; Nora Idiawati; Deana Wahyuningrum

    2014-01-01

    Ethanol production through ionic liquids pretreatment of palm empty bunch (PEB) was carried out. This research aims to investigate impact of ionic liquids synthetic i.e 1-butyl-3-methyl imidazoliumbromide or [BMIM]bromide toward cellulose’s palm empty bunch and convert its cellulose into bioethanol. Ionic liquid was synthesized  through reflux and microwave assisted synthesis methods. Research investigation showed that microwave assisted synthesis produce [BMIM]bromide 90% faster than reflux ...

  4. Numerical simulation of bubbles motion in lifting pipe of bubble pump for lithium bromide absorption chillers

    International Nuclear Information System (INIS)

    Gao, Hongtao; Liu, Bingbing; Yan, Yuying

    2017-01-01

    A bubble pump is proposed to replace the traditional mechanical solution pump in lithium bromide absorption chillers, for its advantageous feature that can be driven by industrial waste heat or solar energy or other low-grade energy. In two-stage bubble pump driven lithium bromide absorption refrigeration system, flow patterns in lifting pipe have significant effects on the performance of bubble pump. In this paper, the single bubble motion and the double bubbles coalescence in vertical ascending pipe are simulated by an improved free energy model of lattice Boltzmann method, in which the two-phase liquid to gas density ratio is 2778. The details of bubbles coalescence process are studied. Density and velocity of bubbles have been obtained. The computational results show that the initial radius of each bubble has a great influence on the coalescence time. The larger the initial bubble radius, the shorter the coalescence time. The pipe diameter has a little effect on the two bubbles coalescence time while it has a significant effect on the bubble velocity. As the pipe diameter increases, the bubble velocity increases. The obtained results are helpful for studying the transition mechanisms of two-phase flow patterns and useful for improving the bubble pump performance by controlling the flow patterns in lifting pipe.

  5. Effect of chronic administration of phenobarbital, or bromide, on pharmacokinetics of levetiracetam in dogs with epilepsy.

    Science.gov (United States)

    Muñana, K R; Nettifee-Osborne, J A; Papich, M G

    2015-01-01

    Levetiracetam (LEV) is a common add-on antiepileptic drug (AED) in dogs with refractory seizures. Concurrent phenobarbital administration alters the disposition of LEV in healthy dogs. To evaluate the pharmacokinetics of LEV in dogs with epilepsy when administered concurrently with conventional AEDs. Eighteen client-owned dogs on maintenance treatment with LEV and phenobarbital (PB group, n = 6), LEV and bromide (BR group, n = 6) or LEV, phenobarbital and bromide (PB-BR group, n = 6). Prospective pharmacokinetic study. Blood samples were collected at 0, 1, 2, 4, and 6 hours after LEV administration. Plasma LEV concentrations were determined by high-pressure liquid chromatography. To account for dose differences among dogs, LEV concentrations were normalized to the mean study dose (26.4 mg/kg). Pharmacokinetic analysis was performed on adjusted concentrations, using a noncompartmental method, and area-under-the-curve (AUC) calculated to the last measured time point. Compared to the PB and PB-BR groups, the BR group had significantly higher peak concentration (Cmax ) (73.4 ± 24.0 versus 37.5 ± 13.7 and 26.5 ± 8.96 μg/mL, respectively, P phenobarbital in dogs. Copyright © 2015 by the American College of Veterinary Internal Medicine.

  6. Analysis of infiltration through mill tailings using a bromide tracer

    International Nuclear Information System (INIS)

    Lewis, G.J.; Stephens, D.B.

    1985-01-01

    Infiltration of precipitation into tailings impoundments as a means of recharge to underlying materials is often considered insignificant, particularly in arid and semi-arid environments. A series of experiments was performed to investigate the behavior of infiltrated precipitation into tailing soils, by the use of a bromide tracer. A bromide tracer was applied to the surface of columns driven into the tailings to monitor downward advancement of tracer-laden water. Controlled laboratory experiments on the behavior of the bromide tracer under varying precipitation events and initial soil moisture contents were also conducted. Results indicate that a definite downward migration of infiltrated precipitation occurs, particularly with large magnitude precipitation events, and that, eventually, some fraction of the infiltrated precipitation may continue downward below the zone affected by evaporation. The use of an artificially applied bromide tracer to monitor depth of infiltration of precipitation is a simple, safe technique that can provide valuable information for long-term tailings management strategies at low cost

  7. Exposure to methyl bromide during greenhouse fumigation on Crete, Greece

    NARCIS (Netherlands)

    Vreede, J.A.F. de; Boeft, J. den; Hemmen, J.J. van

    1998-01-01

    In agricultural areas where greenhouses and dwellings are intermixed, the general population as well as the professional applicators may be exposed to pesticides. In a field study on Crete, exposure to methyl bromide during soil fumigation was assessed. Exposure of applicators (both contractors and

  8. Revisiting the Kinetics and Mechanism of Bromate-Bromide Reaction

    Directory of Open Access Journals (Sweden)

    Côrtes Carlos Eduardo S.

    2001-01-01

    Full Text Available The bromate-bromide reaction was investigated in an acidity range not studied yet. The reaction was followed at the Br2/Br3- isosbestic point (lambda = 446 nm. It was observed a first-order behavior for bromate and bromide ions and a second-order behavior for H+ ion that results in the rate law nu = k[BrO3-][Br- ][H+]². This rate law suggests a mechanism involving two successive protonation of bromate followed by the interaction of the intermediate species H2BrO3+ with bromide. These results disagree with the obtained by other authors who observed a second-order behavior for the bromide and first-order for H+, and have proposed intermediate species like H2Br2O3 and HBr2O3-. The second-order for [H+] observed in the range 0.005 <= [H+] <= 2.77 mol L-1 sets down that the pKa of bromic acid, HBrO3, must be lower than -0.5 (T = 25 °C, different from all other values for this pKa proposed in the literature.

  9. Ipratropium bromide delivered by metered-dose aerosol to infant ...

    African Journals Online (AJOL)

    1990-08-21

    Aug 21, 1990 ... Two methods of administration of ipratropium bromide. (Atrovent; Boehringer Ingelheim) to wheezing children'< 25 months of age were compared: (I) the conventional nebulisa- tion (15 children); and (iI) a metered-dose aerosol plus spacer and mask (MDA group, 17 children). The drug induced a significant ...

  10. Ipratropium bromide delivered by metered-dose aerosol to infant ...

    African Journals Online (AJOL)

    Two methods of administration of ipratropium bromide (Atrovent; Boehringer Ingelheim) to wheezing children'< 25 months of age were compared: (i) the conventional nebulisation (15 children); and (ii) a metered-dose aerosol plus spacer and mask (MDA group, 17 children). The drug induced a significant and similar fall in ...

  11. 7 CFR 305.6 - Methyl bromide fumigation treatment schedules.

    Science.gov (United States)

    2010-01-01

    ... 12 40 or above 16 8 T408-g-1 Chamber 60 or above 10 24 60 or above 20 15.5 T408-g-2 Tarpaulin 60 or..., fumigation with methyl bromide for sapote fruit fly. Regulated citrus fruits originating inside an area quarantined for sapote fruit fly that are to be moved outside the quarantined area may be treated with methyl...

  12. Study of methyl bromide reactivity with human and mouse hemoglobin

    African Journals Online (AJOL)

    A study has been carried out on in-vitro reactivity of human and mouse hemoglobin spectrophotometrically at physiological pH, using different protein to reagent ratios. Hemoglobin side chains were modified with different concentrations of methyl bromide on agro-soil fumigant. To ascertain if the site of alkylation was the ...

  13. Preparation of pyridostigmine bromide labeled with carbon-14 and tritium

    Energy Technology Data Exchange (ETDEWEB)

    Kepler, J.A.; Twine, C.E.; Austin, R.D. (Research Triangle Inst., Research Triangle Park, NC (United States))

    1992-08-01

    [2-[sup 14]C]Pyridostigmine bromide was prepared in 17.6% radiochemical yield with specific activity of 18 mCi/mmol. The reaction sequence involved preparation of 2-furan[[sup 14]C]carboxylic acid by carbonation of 2-lithiofuran, followed by conversion to 2-amino[[sup 14]C]methylfuran by lithium aluminium hydride reduction of its carboxamide. Oxidative rearrangement of 2-amino[[sup 14]C]methylfuran gave 3-hydroxy[2-[sup 14]C]pyridine which was converted to [2-[sup 14]C]pyridostigmine bromide by reaction with dimethylcarbamyl chloride and quarternization with bromomethane. Pyridostigmine bromide labeled in the methyl group of the carbamate function was prepared in 73% yield with specific activity of 37.6 mCi/mmol by reaction of bis-3-pyridyl carbonate with [[sup 14]C]dimethylamine followed by quarternization with bromomethane. [6-[sup 3]H]-Pyridostigmine bromide with specific activity of 22.5 mCi/mmol was prepared by catalytic halogen-tritium replacement of 2,6-dibromo-3-dimethylcarbamyloxypyridine followed by quarternization with bromomethane and back-exchanging the labile 2-tritium. (author).

  14. Preparation of pyridostigmine bromide labeled with carbon-14 and tritium

    International Nuclear Information System (INIS)

    Kepler, J.A.; Twine, C.E.; Austin, R.D.

    1992-01-01

    [2- 14 C]Pyridostigmine bromide was prepared in 17.6% radiochemical yield with specific activity of 18 mCi/mmol. The reaction sequence involved preparation of 2-furan[ 14 C]carboxylic acid by carbonation of 2-lithiofuran, followed by conversion to 2-amino[ 14 C]methylfuran by lithium aluminium hydride reduction of its carboxamide. Oxidative rearrangement of 2-amino[ 14 C]methylfuran gave 3-hydroxy[2- 14 C]pyridine which was converted to [2- 14 C]pyridostigmine bromide by reaction with dimethylcarbamyl chloride and quarternization with bromomethane. Pyridostigmine bromide labeled in the methyl group of the carbamate function was prepared in 73% yield with specific activity of 37.6 mCi/mmol by reaction of bis-3-pyridyl carbonate with [ 14 C]dimethylamine followed by quarternization with bromomethane. [6- 3 H]-Pyridostigmine bromide with specific activity of 22.5 mCi/mmol was prepared by catalytic halogen-tritium replacement of 2,6-dibromo-3-dimethylcarbamyloxypyridine followed by quarternization with bromomethane and back-exchanging the labile 2-tritium. (author)

  15. Capacitive-discharge-pumped copper bromide vapour laser

    International Nuclear Information System (INIS)

    Sukhanov, V B; Fedorov, V F; Troitskii, V O; Gubarev, F A; Evtushenko, Gennadii S

    2007-01-01

    A copper bromide vapour laser pumped by a high-frequency capacitive discharge is developed. It is shown that, by using of a capacitive discharge, it is possible to built a sealed off metal halide vapour laser of a simple design allowing the addition of active impurities into the working medium. (letters)

  16. A study of bromide in the Mandovi-Zuari river system of Goa

    Digital Repository Service at National Institute of Oceanography (India)

    De; Dalal, V.N

    Bromide was the subject of detailed investigation in the Mandovi Zuari river system and information was compiled on its spatial and temporal distribution. A simple mixture relation of Carpenter et. al. was applied and seawater percentage and bromide...

  17. Comparison and Analysis of Lithium Bromide-water Absorption Chillers Using Plastic Heat Transfer Tubes and Traditional Lithium Bromide-water Absorption Chillers

    OpenAIRE

    Xue-dong Zhang

    2010-01-01

    There are extensive applications of lithium bromide-water absorption chillers in industry, but the heat exchangers corrosion and refrigerating capacity loss are very difficult to be solved. In this paper, an experiment was conducted by using plastic heat transfer tubes instead of copper tubes. As an example, for a lithium bromide-water absorption chiller of refrigerating capacity of 35kW, the correlative performance of the lithium bromide-water absorption chiller using pl...

  18. Aluminum electroplating on steel from a fused bromide electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat K. Tripathy; Laura A. Wurth; Eric J. Dufek; Toni Y. Gutknecht; Natalie J. Gese; Paula Hahn; Steven M. Frank; Guy L. Frederickson; J. Stephen Herring

    2014-08-01

    A quaternary bromide bath (LiBr–KBr–CsBr–AlBr3) was used to electro-coat aluminum on steel substrates. The electrolytewas prepared by the addition of AlBr3 into the eutectic LiBr–KBr–CsBr melt. A smooth, thick, adherent and shiny aluminum coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminum coverage. Both salt immersion and open circuit potential measurement suggested that the coatings did display a good corrosionresistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminum coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminumcoating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

  19. Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat Tripathy; Laura Wurth; Eric Dufek; Toni Y. Gutknecht; Natalie Gese; Paula Hahn; Steven Frank; Guy Fredrickson; J Stephen Herring

    2014-08-01

    A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

  20. Use of 82Br and 131I radionuclides in studies of goitrogenic effects of exogenous bromide

    International Nuclear Information System (INIS)

    Stanislav Pavelka

    2012-01-01

    The interference of excessive bromide intake with iodine metabolism in the rat was studied using 82 Br and 131 I radionuclides. Mainly lactating rat dams and their pups were used, in addition to adult male rats, in the present studies. Particularly, the influence of high bromide intake in lactating rat dams on the transfer of iodine and bromide to suckling young through breast milk was evaluated. The induction of hypothyroid status in the pups by high bromide intake in the mothers was proved unambiguously. Excessive bromide in lactating rat dams caused a marked decrease in plasma levels of thyroid hormones both, in the mothers and in their sucklings. The effects of an enhanced bromide intake on the thyroid function in relation to iodine status in the animals were also followed. Marked goitrogenic and thyrotoxic effects of excessive bromide in adult rats were significantly enhanced under the conditions of simultaneous iodine deficiency in the experimental animals. (author)

  1. Zinc Bromide Flow Battery Installation for Islanding and Backup Power

    Science.gov (United States)

    2017-08-09

    demonstrates the energy security and cost benefits of implementing a Zn/Br Flow Battery-based ESS at the Marine Corps Air Station (MCAS) located at...user will be realized through the system’s peak shaving mode. This benefit was also used to calculate the operational cost reductions when using the...EW-201242) Zinc Bromide Flow Battery Installation for Islanding and Backup Power August 2017 This document has been cleared for public release

  2. Multiple cutaneous leiomyomas: Pain relief with pulsed hysocine butyl bromide

    Directory of Open Access Journals (Sweden)

    Kaliyadan Feroze

    2009-01-01

    Full Text Available A 35-year-old male patient presented to our outpatient department, complaining of multiple, raised skin lesions on the forehead and back, associated with intermittent pain, especially on exposure to cold. A diagnosis of cutaneous leiomyoma (type 2 segmental was made, which was confirmed by skin biopsy. The patient was started on a trial of pulsed Hyoscine Butyl bromide tablets, following which the patient had significant relief from pain associated with the lesions.

  3. On the existence of 'L-alanine cadmium bromide'.

    Science.gov (United States)

    Srinivasan, Bikshandarkoil R

    2013-12-01

    It is argued that the recently reported nonlinear optical crystal L-alanine cadmium bromide, grown by slow solvent evaporation method at room temperature [P. Ilayabarathi, J. Chandrasekaran, Spectrochim. Acta 96A (2012) 684-689] is the well-known L-alanine crystal. The isolation of L-alanine crystal is explained due to fractional crystallization. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. On the distribution of bromide and bromide/chlorinity ratios in the waters of the Arabian sea off central Indian coast

    Digital Repository Service at National Institute of Oceanography (India)

    DeSouza, F.P.; SenGupta, R.

    Water samples from surface to 2000 m depth at two stations in the Arabian Sea collected during the 82nd cruise of R V Gaveshani in November, 1980 were analysed for bromide. The average bromide concentration was 0.068 g/kg plus or minus 0...

  5. Designing the lithium bromide air conditioning absorption system for a bus

    International Nuclear Information System (INIS)

    Yusoff Ali; Kamaruzzaman Sopian; Hariadi

    2006-01-01

    A system of air-conditioning using Lithium Bromide absorption system is used as an alternative refrigerant that will not pollute the atmosphere. Lithium Bromide is a chemical salt soluble in water. There is a big difference between vapour compression system and LiBr 2 absorption system. The absorption air conditioning system is made of a generator, a condenser, an evaporator and an absorber with necessary pumps and piping. When LiBr 2 solution is heated under low pressure, water will evaporate first, while LiBr 2 will remain in the solution and will become more concentrated. The water is the refrigerant in this system. The generator, where the water is vapourised, is heated using an electric heater or solar energy. The LiBr 2 weak solution under low pressure in the generator is heated and the water evaporate into vapour. The vapour produced is then cooled in the condenser and then expanded into the evaporator. The refrigerant (water) in evaporator change phase from liquid to vapour by absorbing heat from cooling water, which flow in the coil in the evaporator. The chilled water obtained is then pumped into the fan coil, which will be used in conditioning the passenger area of the bus. The water vapour from the evaporator is absorbed into LiBr 2 solution in the absorber, forming a weak solution of LiBr 2 . the weak solution from the absorber is then pumped back to the generator to regenerate. The absorption system does not use compressor, but requires pumps that need lower input power compared to that of a compressor. The system is considered as a new application for the bus. This will have great potential and will be environmentally friendly. The model in this study will be used for calculation of the cooling load for the bus

  6. EFFICACY OF HYOSCINE BUTYL BROMIDE SUPPOSITORY FOR POSTOPERATIVE PAIN RELIEF

    Directory of Open Access Journals (Sweden)

    Soniya C. Alphonse

    2017-07-01

    Full Text Available BACKGROUND Caesarean Section is on the rise all over the world. Women undergoing Caesarean section often wish to be awake post operatively and to avoid excessive medications affecting interactions with the new born infant. Multimodal pain therapy has been advocated for postoperative pain management after caesarean section. MATERIALS AND METHODS The study is a prospective randomized controlled study conducted at a tertiary care hospital to study the effect of Hyoscine Butyl Bromide Suppositories for postoperative analgesia following elective repeat caesarean section. The study included sixty patients divided into two groups- Group1 (study group were given Hyoscine Butyl Bromide Suppository (10 mg along with Injection. Tramadol 50 mg IM and Group II (control group were given Injection Tramadol IM only at the end of surgery. Pain score of the patient assessed at 1 hr, 2 hrs, 6hrs and 24 hrs post operatively. The total no of doses of injection tramadol needed in 24 hrs and the interval between 1st and 2nd dose of tramadol was also noted. The adverse effects of the drug and additional advantages of the drug if any were also assessed. RESULTS There was no statistically significant difference in pain score during the assessment intervals between the two groups. There was no difference in the number of doses of tramadol needed in the first 24 hrs. The mean interval between the 1st and 2nd dose of tramadol was found to be 7.6538 hours for group 1 patients and 6.9130 for group patients which was found to be statistically significant. There was no statistically significant side effects/ additional advantages for the drugs. CONCLUSION Concurrent administration of Hyoscine Butyl Bromide Suppository (10 mg and injection Tramadol 50 mg IM offers a longer postoperative analgesia without any increased adverse effects.

  7. Four groups of new aromatic halogenated disinfection byproducts: effect of bromide concentration on their formation and speciation in chlorinated drinking water.

    Science.gov (United States)

    Pan, Yang; Zhang, Xiangru

    2013-02-05

    Bromide is naturally present in source waters worldwide. Chlorination of drinking water can generate a variety of chlorinated and brominated disinfection byproducts (DBPs). Although substantial efforts have been made to examine the effect of bromide concentration on the formation and speciation of halogenated DBPs, almost all previous studies have focused on trihalomethanes and haloacetic acids. Given that about 50% of total organic halogen formed in chlorination remains unknown, it is still unclear how bromide concentration affects the formation and speciation of the new/unknown halogenated DBPs. In this study, chlorinated drinking water samples with different bromide concentrations were prepared, and a novel approach-precursor ion scan using ultra performance liquid chromatography/electrospray ionization-triple quadrupole mass spectrometry-was adopted for the detection and identification of polar halogenated DBPs in these water samples. With this approach, 11 new putative aromatic halogenated DBPs were identified, and they were classified into four groups: dihalo-4-hydroxybenzaldehydes, dihalo-4-hydroxybenzoic acids, dihalo-salicylic acids, and trihalo-phenols. A mechanism for the formation of the four groups of new aromatic halogenated DBPs was proposed. It was found that increasing the bromide concentration shifted the entire polar halogenated DBPs as well as the four groups of new DBPs from being less brominated to being more brominated; these new aromatic halogenated DBPs might be important intermediate DBPs formed in drinking water chlorination. Moreover, the speciation of the four groups of new DBPs was modeled: the speciation patterns of the four groups of new DBPs well matched those determined from the model equations, and the reactivity differences between HOBr and HOCl in reactions forming the four groups of new DBPs were larger than those in reactions forming trihalomethanes and haloacetic acids.

  8. Methylation of food commodities during fumigation with methyl bromide

    International Nuclear Information System (INIS)

    Starratt, A.N.; Bond, E.J.

    1990-01-01

    Sites of methylation in several commodities (wheat, oatmeal, peanuts, almonds, apples, oranges, maize, alfalfa and potatoes) during fumigation with 14 C-methyl bromide were studied. Differences were observed in levels of the major volatiles: methanol, dimethyl sulphide and methyl mercaptan, products of O- and S-methylation, resulting from treatment of the fumigated materials with 1N sodium hydroxide. In studies of maize and wheat, histidine was the amino acid which underwent the highest level of N-methylation. (author). 24 refs, 3 tabs

  9. Tiotropium Bromide in Chronic Obstructive Pulmonary Disease and Bronchial Asthma.

    Science.gov (United States)

    Alvarado-Gonzalez, Alcibey; Arce, Isabel

    2015-11-01

    Inhaled bronchodilators are the mainstay of pharmacological treatment for stable chronic obstructive pulmonary disease (COPD), including β2-agonists and muscarinic antagonists. Tiotropium bromide, a long-acting antimuscarinic bronchodilator (LAMA), is a treatment choice for moderate-to-severe COPD; its efficacy and safety have been demonstrated in recent trials. Studies also point to a beneficial role of tiotropium in the treatment of difficult-to-control asthma and a potential function in the asthma-COPD overlap syndrome (ACOS). Combination of different bronchodilator molecules and addition of inhaled corticosteroids are viable therapeutic alternatives. A condensation of the latest trials and the rationale behind these therapies will be presented in this article.

  10. Transient anisocoria in a patient treated with nebulized ipratropium bromide

    Directory of Open Access Journals (Sweden)

    Renato Pejic

    2017-09-01

    Conclusions and importance: Presence of anisocoria may be a concerning neurological sign. If there are no other neurological or ophthalmological signs and symptoms and a recent ipratropium bromide inhalation treatment exists in the patient's history, we should consider iatrogenic side-effect of drugs as a possible reason of anisocoria and possibly spare the patient extensive and invasive diagnostic procedures that can also raise costs of treatment significantly. Observing neurological status and testing with 1% pilocarpine solution may be necessary to determine the etiology of this condition.

  11. Suicide by intravenous injection of rocuronium-bromide: Case report

    Directory of Open Access Journals (Sweden)

    Nikolić Slobodan

    2005-01-01

    Full Text Available Suicides by intravenous injection of an overdose of medicaments are uncommon. In this paper, we present the case of a suicide by rocuronium-bromide injection in combination with an oral overdose of metoprolol. Unfortunately, in Belgrade, there is no toxicological laboratory capable of detecting rocuronium. The interpretation of autopsy and toxicological data in this case was made difficult due to the extreme putrefaction of the body of the deceased. So, by forensic investigation, the case was solved indirectly, through circumstantial evidence: an empty ampoule of rocuronium found near the body, as well as a plastic syringe and cloth-bandage found in the left hand of the deceased.

  12. Spectrophotometric determination of indium with chromazurol S and dimethyllaurylbenzylammonium bromide

    International Nuclear Information System (INIS)

    Kwapulinska, G.; Buhl, F.

    1988-01-01

    The ternary system: indium-chromazurol S (CHAS)-dimethyllaurylbenzylammonium bromide (ST) was applied for determination of microgramme amounts of indium. The addition of ST enhances the sensitivity of the method; at λ max =625 nm the molar absorptivity of In-CHAS-ST complex equals 1.74 x 10 5 . The system obeyes the Lambert-Beer law in the range of indium concentration from 0.04 to 0.48 ppm. The maximal absorbance was obtained at pH 6. The complex is formed immediately and is stable during 2 hours. 3 figs., 10 refs. (author)

  13. Power Plant Bromide Discharges and Downstream Drinking Water Systems in Pennsylvania.

    Science.gov (United States)

    Good, Kelly D; VanBriesen, Jeanne M

    2017-10-17

    Coal-fired power plants equipped with wet flue gas desulfurization (FGD) systems have been implicated in increasing bromide levels and subsequent increases in disinfection byproducts at downstream drinking water plants. Bromide was not included as a regulated constituent in the recent steam electric effluent limitations guidelines and standards (ELGs) since the U.S. EPA analysis suggested few drinking water facilities would be affected by bromide discharges from power plants. The present analysis uses a watershed approach to identify Pennsylvania drinking water intakes downstream of wet FGD discharges and to assess the potential for bromide discharge effects. Twenty-two (22) public drinking water systems serving 2.5 million people were identified as being downstream of at least one wet FGD discharge. During mean August conditions (generally low-flow, minimal dilution) in receiving rivers, the median predicted bromide concentrations contributed by wet FGD at Pennsylvania intake locations ranged from 5.2 to 62 μg/L for the Base scenario (including only natural bromide in coal) and from 16 to 190 μg/L for the Bromide Addition scenario (natural plus added bromide for mercury control); ranges depend on bromide loads and receiving stream dilution capacity.

  14. Transient neuromyopathy after bromide intoxication in a dog with idiopathic epilepsy

    Directory of Open Access Journals (Sweden)

    Steinmetz Sonja

    2012-12-01

    Full Text Available Abstract A seven-year old Australian Shepherd, suffering from idiopathic epilepsy under treatment with phenobarbitone and potassium bromide, was presented with generalised lower motor neuron signs. Electrophysiology and muscle-nerve biopsies revealed a neuromyopathy. The serum bromide concentration was increased more than two-fold above the upper reference value. Clinical signs disappeared after applying diuretics and reducing the potassium bromide dose rate. This is the first case report describing electrophysiological and histopathological findings associated with bromide induced lower motor neuron dysfunction in a dog.

  15. Acute effect of methyl bromide on sleep-wakefulness and its

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, S; Arito, H; Abuku, S; Imamiya, S

    1986-01-01

    In an attempt to clarify the acute effects of methyl bromide on the central nervous system, abnormal electrocorticographic activity and changes in sleep-wakefulness and its circadian rhythms were investigated after a single injection of methyl bromide. The effects of possible hydrolyzed products of methyl bromide, methanol and bromine ions on sleep and its rhythms were also examined. It was found that the hydrolyzed products of methyl bromide, bromine ions and methanol exerted little effect on the amounts of wakefulness (W), non-REM sleep (NREMS) and REM sleep (REMS) at the same molar dose as 45 mg methyl bromide/kg. Thus, it can be concluded that the methyl bromide-induced changes in sleep-wakefulness and its circadian rhythms are due to methyl bromide and not to the hydrolyzed products. It was also found that amounts of W, NREMS and REMS were changed dose-dependently after a single injection of methyl bromide and that methyl bromide significantly disrupted the circadian REMS rhythm. 17 references, 1 figure, 1 table.

  16. Vapour pressures, densities, and viscosities of the (water + lithium bromide + potassium acetate) system and (water + lithium bromide + sodium lactate) system

    International Nuclear Information System (INIS)

    Lucas, Antonio de; Donate, Marina; Rodriguez, Juan F.

    2006-01-01

    Measurements of thermophysical properties (vapour pressure, density, and viscosity) of the (water + lithium bromide + potassium acetate) system LiBr:CH 3 COOK = 2:1 by mass ratio and the (water + lithium bromide + sodium lactate) system LiBr:CH 3 CH(OH)COONa = 2:1 by mass ratio were measured. The system, a possible new working fluid for absorption heat pump, consists of absorbent (LiBr + CH 3 COOK) or (LiBr + CH 3 CH(OH)COONa) and refrigerant H 2 O. The vapour pressures were measured in the ranges of temperature and absorbent concentration from T = (293.15 to 333.15) K and from mass fraction 0.20 to 0.50, densities and viscosities were measured from T = (293.15 to 323.15) K and from mass fraction 0.20 to 0.40. The experimental data were correlated with an Antoine-type equation. Densities and viscosities were measured in the same range of temperature and absorbent concentration as that of the vapour pressure. Regression equations for densities and viscosities were obtained with a minimum mean square error criterion

  17. Field-scale transport of water and bromide in a cracking clay soil

    NARCIS (Netherlands)

    Hendriks, R.F.A.; Hamminga, W.; Oostindie, K.; Bronswijk, J.J.B.

    1995-01-01

    The transport of a bromide tracer was studied in a cracking heavy clay soil. The soil was sampled six times and the groundwater and drain discharge were sampled frequently. Samples were analysed for bromide content. Solutes were transported in three domains: macropores, such as large continuous

  18. 78 FR 36507 - Notice of Availability of a Treatment Evaluation Document; Methyl Bromide Fumigation of Blueberries

    Science.gov (United States)

    2013-06-18

    ... treatment schedule for blueberries at a temperature of 60[emsp14][deg]F at a dosage rate of 2 lbs gas/1,000...] Notice of Availability of a Treatment Evaluation Document; Methyl Bromide Fumigation of Blueberries... and Quarantine Treatment Manual an additional treatment schedule for methyl bromide fumigation of...

  19. Thermochromatic investigation of some bromides and comparison with the corresponding chlorides

    International Nuclear Information System (INIS)

    Kim U Zin; Timokhin, S.N.; Zvara, I.

    1988-01-01

    The thermochromatographic behaviour of chlorides and bromides of La, Tb, Ag, Mn, Cs, Zn, Au, Zr, Hf, Nb ('carrier-free' nuclides) in quartz column was studied. From the experimental data a correlation was observed between the deposition temperature on the column and the enthalpy of sublimation of the chlorides and bromides. The enthalpy of adsortion of the halides were also evaluated. (author)

  20. Pancreatitis associated with potassium bromide/phenobarbital combination therapy in epileptic dogs.

    OpenAIRE

    Gaskill, C L; Cribb, A E

    2000-01-01

    In a retrospective study, at least 10% of dogs receiving potassium bromide/phenobarbital combination therapy, compared with 0.3% of dogs receiving phenobarbital monotherapy, had probable pancreatitis. Pancreatitis may be a more frequent and more serious adverse effect of potassium bromide/phenobarbital combination therapy than has been reported previously.

  1. Rejection of Bromide and Bromate Ions by a Ceramic Membrane.

    Science.gov (United States)

    Moslemi, Mohammadreza; Davies, Simon H; Masten, Susan J

    2012-12-01

    Effects of pH and the addition of calcium chloride (CaCl(2)) on bromate (BrO(3) (-)) and bromide (Br(-)) rejection by a ceramic membrane were investigated. Rejection of both ions increased with pH. At pH 8, the rejection of BrO(3) (-) and Br(-) was 68% and 63%, respectively. Donnan exclusion appears to play an important role in determining rejection of BrO(3) (-) and Br(-). In the presence of CaCl(2), rejection of BrO(3) (-) and Br(-) ions was greatly reduced, confirming the importance of electrostatic interactions in determining rejection of BrO(3) (-) and Br(-). The effect of Ca(2+) is so pronounced that in most natural waters, rejection of both BrO(3) (-) and Br(-) by the membrane would be extremely small.

  2. Hyoscine-N-Butyl-Bromide-Induced Hypotension and Myocardial Ischemia

    Directory of Open Access Journals (Sweden)

    Guan-Liang Chen

    2013-01-01

    Full Text Available Hyoscine N-butyl bromide, also known as scopolamine, is a type of antimuscarinic agent. This drug is associated with numerous common side effects, including abdominal fullness, constipation, urinary retention, blurred vision, skin flushing, tachycardia, decreased sweating, and salivation. The most unfavorable side effect is hemodynamic instability. In the present case, hypotension and acute myocardial infarction developed after intravenous hyoscine injection as a premedication therapy for colonoscopy. It was difficult to differentiate the cause-effect relationship between myocardial infarction and hypotension. Because both conditions were present under drug effects, we considered 2 possible diagnoses. One was coronary spasm with cardiogenic shock, and the other was myocardial ischemic sequela due to shock status. The latter diagnosis was confirmed after a series of examinations.

  3. Irradiation as an alternative to methyl bromide: the Australian situation

    Energy Technology Data Exchange (ETDEWEB)

    Heather, N W [Gatton College, University of Queensland, Queensland (Australia)

    1999-05-01

    International agreement to phase out the fumigant Methyl bromide (MeBr) will have serious implications for pest and disease control in Australia, particularly grain pest control, quarantine usage on fresh horticultural produce and control of soil pathogens or nematodes. Irradiation is a practical alternative but is not currently approved for use in Australia. Other options are available but none of the viable methods except irradiation have the short application time needed for treatment of grams found to be infested during loading at export. This usage is vital, as Australian grain is exported at very high standards of freedom from insects, assured by Government regulatory requirements. Irradiation is contrasted against other alternatives including heat and cold, especially for fresh horticultural produce. (author) 4 refs, 5 tabs

  4. Irradiation as an alternative to methyl bromide: the Australian situation

    International Nuclear Information System (INIS)

    Heather, N.W.

    1999-01-01

    International agreement to phase out the fumigant Methyl bromide (MeBr) will have serious implications for pest and disease control in Australia, particularly grain pest control, quarantine usage on fresh horticultural produce and control of soil pathogens or nematodes. Irradiation is a practical alternative but is not currently approved for use in Australia. Other options are available but none of the viable methods except irradiation have the short application time needed for treatment of grams found to be infested during loading at export. This usage is vital, as Australian grain is exported at very high standards of freedom from insects, assured by Government regulatory requirements. Irradiation is contrasted against other alternatives including heat and cold, especially for fresh horticultural produce. (author)

  5. The sorption behavior of DDT onto sediment in the presence of surfactant cetyltrimethylammonium bromide

    International Nuclear Information System (INIS)

    Cao Xiaoyan; Han Huayu; Yang Guipeng; Gong Xiaofei; Jing Jianning

    2011-01-01

    Highlights: → The sorption behavior of a complex system consists of DDT and CTAB onto marine sediment was studied. → Batch experiments were carried out to investigate the kinetics and thermodynamics. → The presence of CTAB could remarkably accelerate and enhance the sorption of DDT. → The sorption of DDT had relatively more negative ΔG 0 and ΔH 0 in the presence of CTAB. - Abstract: The sorption behavior of p,p'- and o,p'-dichlorodiphenyltrichloroethane (DDT) in the presence of a cationic surfactant cetyltrimethylammonium bromide (CTAB) on sediment was studied. Batch experiments were carried out to investigate the kinetics and thermodynamics of the process. The kinetic behavior of these three chemicals on sediment was described by pseudo-second-order kinetic equations, and the isotherms followed the Freundlich model well. The presence of CTAB was able to remarkably accelerate and enhance the sorption of DDT, whereas DDT showed no effect on the sorption of CTAB in our considered concentration ranges. The thermodynamic parameters, such as standard enthalpy change (ΔH 0 ), standard entropy change (ΔS 0 ) and standard Gibbs free energy change (ΔG 0 ) showed that the sorption process of p,p'- and o,p'-DDT was physical, spontaneous and exothermic, and the randomness at the solid-liquid interface increased during the process. In the presence of CTAB, the sorption of DDT showed significantly negative ΔG 0 and ΔH 0 values.

  6. Characterization of Jamaican agro-industrial wastes. Part II, fatty acid profiling using HPLC: precolumn derivatization with phenacyl bromide.

    Science.gov (United States)

    Bailey-Shaw, Y A; Golden, K D; Pearson, A G M; Porter, R B R

    2012-09-01

    This paper describes the determination of fatty acid composition of coffee, citrus and rum distillery wastes using reversed-phase high-performance liquid chromatography (RP-HPLC). Lipid extracts of the waste samples are derivatized with phenacyl bromide and their phenacyl esters are separated on a C8 reversed-phase column by using continuous gradient elution with water and acetonitrile. The presence of saturated and unsaturated fatty acids in quantifiable amounts in the examined wastes, as well as the high percentage recoveries, are clear indications that these wastes have potential value as inexpensive sources of lipids. The HPLC procedures described here could be adopted for further analysis of materials of this nature.

  7. Liquids and liquid mixtures

    CERN Document Server

    Rowlinson, J S; Baldwin, J E; Buckingham, A D; Danishefsky, S

    2013-01-01

    Liquids and Liquid Mixtures, Third Edition explores the equilibrium properties of liquids and liquid mixtures and relates them to the properties of the constituent molecules using the methods of statistical thermodynamics. Topics covered include the critical state, fluid mixtures at high pressures, and the statistical thermodynamics of fluids and mixtures. This book consists of eight chapters and begins with an overview of the liquid state and the thermodynamic properties of liquids and liquid mixtures, including vapor pressure and heat capacities. The discussion then turns to the thermodynami

  8. Synthesis of 2-Isopropyl Naphthalene Catalyzed by Et3NHCl-AlCl3 Ionic Liquids

    Institute of Scientific and Technical Information of China (English)

    Li Chenmin; Qi Xin; Tang Xiangyang

    2014-01-01

    In this paper, 2-isopropyl naphthalene has been synthesized by the reaction of naphthalene and isopropyl bromide, using triethylamine hydrochloride-aluminum chloride ionic liquid as the catalyst. The effect of the catalyst composition, the reaction time, the reaction temperature, the ionic liquid dosage, as well as the molar ratio of the reagents on the 2-isopropyl naphthalene yield was systematically investigated. The optimal reaction conditions cover:an AlCl3 to Et3NHCl ratio of 2.0, a reaction time of 3 h, a reaction temperature of 15.0℃, a volume fraction of ionic liquid to the mixture (isopropyl bromide, n-dodecane and n-hexane) of 9%, and a naphthalene/isopropyl bromide molar ratio of 4.0. Under the optimal reaction condi-tions, the conversion of isopropyl bromide reached 98%and the selectivity of 2-isopropyl naphthalene was equal to 80%. The test results veriifed good catalytic activity upon using Et3NHCl-AlCl3 ionic liquid as the catalyst for alkylation of naph-thalene with isopropyl bromide. The activity of the ionic liquid remains unchanged after it has been recycled for 4 times.

  9. Evaluation of alkali bromide salts for potential pyrochemical applications

    International Nuclear Information System (INIS)

    Tripathy, P.K.; Gutknecht, T.Y.; Herrmann, S.D.; Fredrickson, G.L.; Lister, T.E.

    2013-01-01

    Transient techniques were employed to study the electrochemical behavior, reduction mechanism and transport properties of REBr 3 (RE - La, Nd and Gd) in pure LiBr, LiBr-KBr (eutectic) and LiBr-KBr-CsBr (eutectic) melts. Gd(III) showed a reversible single step soluble-insoluble exchange phenomenon in LiBr melt at 973 K. Although La (III), Nd(III) and Gd(III) ions showed reversible behavior in eutectic LiBr-KBr melts, these ions showed a combination of temperature dependent reversible and pseudo-reversible behavior. While both La(III) and Gd(III) showed one step reduction, the reduction of Nd(III) was observed to be a two step process. La metal could be electrodeposited from the ternary electrolyte at a temperature of 673 K. Various electrochemical measurements suggest that both binary and ternary bromide melts can potentially be used to electro-deposit high purity RE metals at comparatively lower operating temperatures. (authors)

  10. IPRATROPIUM BROMIDE FOR ACUTE ASTHMA IN CHILDREN: A RETROSPECTIVE TRIAL.

    Science.gov (United States)

    Nomura, Osamu; Morikawa, Yoshihiko; Hagiwara, Yusuke; Ihara, Takateru; Inoue, Nobuaki; Sakakibara, Hiroshi; Akasawa, Akira

    Inhaled anticholinergics such as ipratropium bromide (IB), when administered with β2-agonists, are effective in reducing hospital admissions of children presenting to the emergency department with moderate to severe asthma. However, treatment of acute asthma with IB is still uncommon in Japan. The aim of this study was to investigate the effectiveness and safety of IB for the treatment of pediatric acute asthma. We conducted a retrospective study to compare the admission rate of patients who received IB with those who did not. Patients aged 4 years or older with a history of moderate to severe attacks were included. For analysis, propensity score matching was used to adjust the confounding factors related to IB use. Patients received IB by metered-dose inhaler (40μg per dose) with a spacer three times at 20-min intervals. Among 175 patients included in the analysis, 102 patients were treated with IB (IB group) and 73 patients were treated without IB (Non-IB group). A propensity score matching analysis extracted 63 patients from each group. There was no statistical difference between the two groups in terms of admission rate (IB group 12.7% vs Non-IB group 9.5%; p=0.78). One patient (1.0%) treated with IB experienced dryness of the mouth, which resolved spontaneously. The admission rate did not decline with IB use. Several confounding factors could have influenced and limited our results. A prospective study is needed to investigate the effectiveness of IB in Japan.

  11. Factors affecting a cyanogen bromide-based assay of thiamin.

    Science.gov (United States)

    Wyatt, D T; Lee, M; Hillman, R E

    1989-11-01

    We analyzed extensively a modified thiochrome method for thiamin analysis. Acid phosphatase (EC 3.1.3.2) from potato was superior to either alpha-amylase or acid phosphatase from wheat germ as a dephosphorylating agent. Timing of cyanogen bromide exposure was important, but the assay had good precision and accuracy. The standard curve was linear from 10 to 3000 nmol/L. The within-run and between-run coefficients of variation for total thiamin in whole blood were 3.6% and 7.4%, respectively. Analytical recoveries for low, intermediate, and high additions of thiamin to whole blood were 93-109%. Sample yield was increased by 41% (+/- 29% SD) with pre-assay freezing. Samples were stable for two days at room temperature, for seven days when refrigerated, and for two years when frozen. Previously unreported interference was seen with penicillin derivatives, and with several commonly used diuretic and antiepileptic medications. This assay may be suitable for population screening; 200 samples could be analyzed weekly at a cost of +0.20 per sample.

  12. Evaluation of Alkali Bromide Salts for Potential Pyrochemical Applications

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat K. Tripathy; Steven D. Herrmann; Guy L. Fredrickson; Tedd E. Lister; Toni Y. Gutknecht

    2013-10-01

    Transient techniques were employed to study the electrochemical behavior, reduction mechanism and transport properties of REBr3 (RE - La, Nd and Gd) in pure LiBr, LiBr-KBr (eutectic) and LiBr-KBr-CsBr (eutectic) melts. Gd(III) showed a reversible single step soluble-insoluble exchange phenomenon in LiBr melt at 973K. Although La (III), Nd(III) and Gd(III) ions showed reversible behavior in eutectic LiBr-KBr melts, these ions showed a combination of temperature dependent reversible and pseudo-reversible behavior. While both La(III) and Gd(III) showed one step reduction, the reduction of Nd(III) was observed to be a two step process. La metal could be electrodeposited from the ternary electrolyte at a temperature of 673K. Various electrochemical measurements suggest that both binary and ternary bromide melts can potentially be used to electrodeposit high purity RE metals at comparatively lower operating temperatures.

  13. Absorber performance of a water/lithium-bromide absorption chiller

    International Nuclear Information System (INIS)

    Xie Guozhen; Sheng Guogang; Bansal, Pradeep Kumar; Li, Guang

    2008-01-01

    An absorber is one of the most important components of a lithium-bromide absorption chiller (LBAC) as its absorbing characteristics directly influence the performance of the whole chiller. It has been indicated that the absorbing efficiency and cooling capacity could be improved by increasing the solution concentration. In this paper, based on the mechanism of falling film absorption on horizontal tubes, the theoretical models of falling film absorption on horizontal tubes have been established. A series of programs used for computing the theoretical mathematical models, including simulation of LBAC cycle and falling film absorption, have been programmed. The models have been validated reasonably by the experimental data. The results show that the cooling capacity of the LBAC varies in parabola shape of curve with the solution concentration from 52.5% to 58.5%, and that the best coefficient of performance (COP) occurs at concentration of 57%. The investigation proposes the absorbing process of sub-steady thermodynamic equilibrium for the duality solution under increase absorbing pressure

  14. Advanced crystal growth techniques for thallium bromide semiconductor radiation detectors

    Science.gov (United States)

    Datta, Amlan; Becla, Piotr; Guguschev, Christo; Motakef, Shariar

    2018-02-01

    Thallium Bromide (TlBr) is a promising room-temperature radiation detector candidate with excellent charge transport properties. Currently, Travelling Molten Zone (TMZ) technique is widely used for growth of semiconductor-grade TlBr crystals. However, there are several challenges associated with this type of crystal growth process including lower yield, high thermal stress, and low crystal uniformity. To overcome these shortcomings of the current technique, several different crystal growth techniques have been implemented in this study. These include: Vertical Bridgman (VB), Physical Vapor Transport (PVT), Edge-defined Film-fed Growth (EFG), and Czochralski Growth (Cz). Techniques based on melt pulling (EFG and Cz) were demonstrated for the first time for semiconductor grade TlBr material. The viability of each process along with the associated challenges for TlBr growth has been discussed. The purity of the TlBr crystals along with its crystalline and electronic properties were analyzed and correlated with the growth techniques. Uncorrected 662 keV energy resolutions around 2% were obtained from 5 mm x 5 mm x 10 mm TlBr devices with virtual Frisch-grid configuration.

  15. Improved spectrometric characteristics of thallium bromide nuclear radiation detectors

    CERN Document Server

    Hitomi, K; Shoji, T; Suehiro, T; Hiratate, Y

    1999-01-01

    Thallium bromide (TlBr) is a compound semiconductor with a high atomic number and wide band gap. In this study, nuclear radiation detectors have been fabricated from the TlBr crystals. The TlBr crystals were grown by the horizontal travelling molten zone (TMZ) method using the materials purified by many pass zone refining. The crystals were characterized by measuring the resistivity, the mobility-lifetime (mu tau) product and the energy required to create an electron-hole pair (the epsilon value). Improved energy resolution has been obtained by the TlBr radiation detectors. At room temperature the full-width at half-maximum (FWHM) for the 59.5, 122 and 662 keV gamma-ray photo peak obtained from the detectors were 3.3, 8.8 and 29.5 keV, respectively. By comparing the saturated peak position of the TlBr detector with that of the CdTe detector, the epsilon value has been estimated to be about 5.85 eV for the TlBr crystal.

  16. Fabrication of double-sided thallium bromide strip detectors

    Energy Technology Data Exchange (ETDEWEB)

    Hitomi, Keitaro, E-mail: keitaro.hitomi@qse.tohoku.ac.jp [Department of Quantum Science and Energy Engineering, Graduate School of Engineering, Tohoku University, Sendai 980-8579 (Japan); Nagano, Nobumichi [Department of Quantum Science and Energy Engineering, Graduate School of Engineering, Tohoku University, Sendai 980-8579 (Japan); Onodera, Toshiyuki [Department of Electronics and Intelligent Systems, Tohoku Institute of Technology, Sendai 982-8577 (Japan); Kim, Seong-Yun; Ito, Tatsuya; Ishii, Keizo [Department of Quantum Science and Energy Engineering, Graduate School of Engineering, Tohoku University, Sendai 980-8579 (Japan)

    2016-07-01

    Double-sided strip detectors were fabricated from thallium bromide (TlBr) crystals grown by the traveling-molten zone method using zone-purified materials. The detectors had three 3.4-mm-long strips with 1-mm widths and a surrounding electrode placed orthogonally on opposite surfaces of the crystals at approximately 6.5×6.5 mm{sup 2} in area and 5 mm in thickness. Excellent charge transport properties for both electrons and holes were observed from the TlBr crystals. The mobility-lifetime products for electrons and holes in the detector were measured to be ~3×10{sup −3} cm{sup 2}/V and ~1×10{sup −3} cm{sup 2}/V, respectively. The {sup 137}Cs spectra corresponding to the gamma-ray interaction position were obtained from the detector. An energy resolution of 3.4% of full width at half maximum for 662-keV gamma rays was obtained from one “pixel” (an intersection of the strips) of the detector at room temperature.

  17. Chloride, bromide and iodide scintillators with europium doping

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2014-08-26

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  18. A comparison of the effect of intranasal desmopressin and intramuscular hyoscine N-butyl bromide combination with intramuscular hyoscine N-butyl bromide alone in acute renal colic

    Directory of Open Access Journals (Sweden)

    Abdol-Reza Kheirollahi

    2010-01-01

    Full Text Available Background: Patients with acute renal colic usually require immediate diagnosis and treatment. In this clinical trial analgesic effect of hyoscine N-butyl bromide and desmopressin combination in comparison with hyoscine N-butyl bromide alone in patients with acute renal colic induced by urinary stones was assessed. Methods: The study included 114 patients randomly allocated in two groups (A and B. Patients in group A received 20 mg intramuscular hyoscine N-butyl bromide at admission time and patients in group B received 20 μg of intranasal desmopressin in combination with 20 mg intramuscular hyoscine N-butyl bromide. A visual analogue scale (VAS; a 10-cm horizontal scale ranging from "zero or no pain" to "10 or unbearable pain" was hired to assess the patients′ pain severity at baseline, 30 and 60 minutes after the treatments. Results: On admission, the pain level was similar in both groups (group A: 8.95 ± 0.11 and group B: 8.95 ± 0.12. In group A, the mean of pain level showed a decrease after 30 minutes (group A: 7.26 ± 0.25 and group B: 5.95 ± 0.28 but further decreasing did not occur; however in group B, the pain consistently decreased and the mean after 60 minutes was significantly decreased (group A: 6.80 ± 0.31 and group B: 3.71 ± 0.31. No side effects were detected in this study. Conclusions: The combination of hyoscine N-butyl bromide and desmopressin is more effective than hyoscine N-butyl bromide alone in patients with renal colic. Further studies are recommended to validate these findings and compare the different doses of desmopressin.

  19. CHLORPYRIFOS TRANSFORMATION BY AQUEOUS CHLORINE IN THE PRESENCE OF BROMIDE AND NATURAL ORGANIC MATTER

    Science.gov (United States)

    The aqueous chlorination of chlorpyrifos (CP) was investigated in the presence of bromide and natural organic matter (NOM), which were identified as naturally occurring aqueous constituents that could impact CP transformation rates to the toxic product chlorpyrifos oxon (CPO). Br...

  20. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Treatment Longer than 8 Hours

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  1. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Treatment 8 Hours or Less

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  2. Tribromoisocyanuric acid/triphenylphosphine: a new system for conversion of alcohols into alkyl bromides

    International Nuclear Information System (INIS)

    Andrade, Vitor S.C. de; Mattos, Marcio C.S. de

    2014-01-01

    An efficient and facile method has been developed for the conversion of alcohols into alkyl bromides under neutral conditions using tribromoisocyanuric acid and triphenylphosphine (molar ratio 1.0:0.7:2.0, alcohol/tribromoisocyanuric acid/triphenylphosphine) in dichloromethane at room temperature. This method can be applied for the conversion of primary, secondary, benzilic and allylic alcohols, and their corresponding bromides are obtained in 67-82 % yield. Tertiary alcohols do not react under these conditions. (author)

  3. Tribromoisocyanuric acid/triphenylphosphine: a new system for conversion of alcohols into alkyl bromides

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Vitor S.C. de; Mattos, Marcio C.S. de, E-mail: mmattos@iq.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Instituto de Quimica. Departamento de Quimica Organica

    2014-05-15

    An efficient and facile method has been developed for the conversion of alcohols into alkyl bromides under neutral conditions using tribromoisocyanuric acid and triphenylphosphine (molar ratio 1.0:0.7:2.0, alcohol/tribromoisocyanuric acid/triphenylphosphine) in dichloromethane at room temperature. This method can be applied for the conversion of primary, secondary, benzilic and allylic alcohols, and their corresponding bromides are obtained in 67-82 % yield. Tertiary alcohols do not react under these conditions. (author)

  4. Influence of bromide on the performance of the amphipod Hyalella azteca in reconstituted waters

    Science.gov (United States)

    Ivey, Chris D.; Ingersoll, Christopher G.

    2016-01-01

    Poor performance of the amphipod Hyalella azteca has been observed in exposures using reconstituted waters. Previous studies have reported success in H. azteca water-only exposures with the addition of relatively high concentrations of bromide. The present study evaluated the influence of lower environmentally representative concentrations of bromide on the response ofH. azteca in 42-d water-only exposures. Improved performance of H. azteca was observed in reconstituted waters with >0.02 mg Br/L.

  5. Stabilized thallium bromide radiation detectors and methods of making the same

    Science.gov (United States)

    Leao, Cedric Rocha; Lordi, Vincenzo

    2015-11-24

    According to one embodiment, a crystal includes thallium bromide (TlBr), one or more positively charged dopants, and one or more negatively charged dopants. According to another embodiment, a system includes a monolithic crystal including thallium bromide (TlBr), one or more positively charged dopants, and one or more negatively charged dopants; and a detector configured to detect a signal response of the crystal.

  6. Dilute Ionic Liquids Pretreatment of Palm Empty Bunch and Its Impact to Produce Bioethanol

    Directory of Open Access Journals (Sweden)

    Lucy Arianie

    2013-12-01

    Full Text Available Ethanol production through ionic liquids pretreatment of palm empty bunch (PEB was carried out. This research aims to investigate impact of ionic liquids synthetic i.e 1-butyl-3-methyl imidazoliumbromide or [BMIM]bromide toward cellulose’s palm empty bunch and convert its cellulose into bioethanol. Ionic liquid was synthesized  through reflux and microwave assisted synthesis methods. Research investigation showed that microwave assisted synthesis produce [BMIM]bromide 90% faster than reflux method. The characterization of synthesized product using FTIR, 1H-NMR, 13C-NMR and LC-MS showed that these reactions have been carried out successfully. Scanning electron microscope figure out changes morphological surface of palm empty bunch caused by ionic liquid pretreatment. Crystallinity index of PEB milled and cellulose of PEFB after [BMIM]bromide dissolution were identified using comparison of PEB FTIR spectrum. Cellulose without dilute [BMIM]bromide have higher LOI number than cellulose after [BMIM]bromide dissolution. It indicated that a large part of cellulose after dissolution has been changed into amorf. Hydrolysis residue of palm empty bunch hydrolyzed by sulfuric acids 5%, 100 0C for 5 hours and produce 685 ppm of reducing sugar. Simultaneous Saccharification and Fermentation using Trichoderma viride and Saccharomyce cerevisiae  for 5 days produce 0,69% of bioethanol.

  7. Dilute Ionic Liquids Pretreatment of Palm Empty Bunch and Its Impact to Produce Bioethanol

    Directory of Open Access Journals (Sweden)

    Lucy Arianie

    2014-06-01

    Full Text Available Ethanol production through ionic liquids pretreatment of palm empty bunch (PEB was carried out. This research aims to investigate impact of ionic liquids synthetic i.e 1-butyl- 3-methyl imidazoliumbromide or [BMIM]bromide toward cellulose’s palm empty bunch and convert its cellulose into bioethanol. Ionic liquid was synthesized through reflux and microwave assisted synthesis methods. Research investigation showed that microwave assisted synthesis produce [BMIM]bromide 90% faster than reflux method. The characterization of synthesized product using FTIR, 1H-NMR, 13C-NMR and LC-MS showed that these reactions have been carried out successfully. Scanning electron microscope figure out changes morphological surface of palm empty bunch caused by ionic liquid pretreatment. Crystallinity index of PEB milled and cellulose of PEFB after [BMIM]bromide dissolution were identified using comparison of PEB FTIR spectrum. Cellulose without dilute [BMIM]bromide have higher LOI number than cellulose after [BMIM]bromide dissolution. It indicated that a large part of cellulose after dissolution has been changed into amorf. Hydrolysis residue of palm empty bunch hydrolyzed by sulfuric acids 5%, 100 0C for 5 hours and produce 685 ppm of reducing sugar. Simultaneous Saccharification and Fermentation using Trichoderma viride and Saccharomyce cerevisiae for 5 days produce 0,69% of bioethanol.

  8. Control of insects with fumigants at low temperatures: toxicity of mixtures of methyl bromide and acrylonitrile to three species of insects

    Energy Technology Data Exchange (ETDEWEB)

    Bond, E.J.; Buckland, C.T.

    1976-12-15

    Acrylonitrile can be mixed with methyl bromide to increase toxicity so that the quantity of methyl bromide required for control of Sitophilus granarius (L.), Tenebrio molitor L., and Tribolium confusum Jacquelin duval is reduced by one half. Mixtures of methyl bromide and acrylonitrile are considerably more effective at low temperatures than methyl bromide alone.

  9. Monitoring of water movement in paddy field's soil using a bromide tracer

    International Nuclear Information System (INIS)

    Asiah Ahmad; Kouichi Yuita

    1994-01-01

    Water movement in soils at the lower course and the middle course of Sakawa River's paddy field was monitored over an 8 week period using a bromide tracer. The water of soil samples taken one day after bromide application contained high concentrations of bromide at 50 to 60 cm soil depth at lower course. The bromide was concentrated promarily within 20 to 80 cm depth. No downward movement below 80 cm depth was detected six weeks afetr the application. This might indicate the high water table of this area. On the other hand, bromide concentrations were high at 50 cm depth in water of the soils sample taken one day after application from the middle course of Sakawa River plot. However, the concentrations were nearly at background level in all samples taken from the middle course of sakawa River 3 weeks after application. The evidence from bromide's movement shows that water readily penetrate the soils at the middle course of Sakawa River. The downward movement was faster compared to that at lower course

  10. Partial molar volume and isentropic compressibility of symmetrical and asymmetrical quaternary ammonium bromides in aqueous solution

    International Nuclear Information System (INIS)

    Moreno, Nicolás; Buchner, Richard; Vargas, Edgar F.

    2015-01-01

    Highlights: • Structural effects of the cations on surrounding water molecules are discussed. • Alkyl-chain geometry determines the hydration of Bu 4 N + isomers. • The “compactness” in the hydration shells varies significantly among the isomers. - Abstract: Values of apparent molar volume and isentropic compressibility of symmetric and asymmetric isomers of tetrabutylammonium bromide, namely tetra-n-butylammonium bromide, tetra-iso-butylammonium bromide, tetra-sec-butylammonium bromide, di-n-butyl-di-iso-butylammonium bromide and di-n-butyl-di-sec-butylammonium bromide, in aqueous solution were determined from density and speed of sound measurements. These properties were obtained as a function of molal concentration within the range of 0.01 < m/mol · kg −1 < 0.1 covering temperatures from 278.15 ⩽ T/K ⩽ 293.15. The partial molar volumes and the apparent isentropic molar compressibility at infinite dilution were calculated and their dependence on temperature examined. The results show that cations with sec-butyl chains have larger structural volumes compared to those with iso-butyl chains. In addition, cations with sec-butyl chains induce smaller structural changes in their hydration shell than the others

  11. The killing of African trypanosomes by ethidium bromide.

    Directory of Open Access Journals (Sweden)

    Arnab Roy Chowdhury

    2010-12-01

    Full Text Available Introduced in the 1950s, ethidium bromide (EB is still used as an anti-trypanosomal drug for African cattle although its mechanism of killing has been unclear and controversial. EB has long been known to cause loss of the mitochondrial genome, named kinetoplast DNA (kDNA, a giant network of interlocked minicircles and maxicircles. However, the existence of viable parasites lacking kDNA (dyskinetoplastic led many to think that kDNA loss could not be the mechanism of killing. When recent studies indicated that kDNA is indeed essential in bloodstream trypanosomes and that dyskinetoplastic cells survive only if they have a compensating mutation in the nuclear genome, we investigated the effect of EB on kDNA and its replication. We here report some remarkable effects of EB. Using EM and other techniques, we found that binding of EB to network minicircles is low, probably because of their association with proteins that prevent helix unwinding. In contrast, covalently-closed minicircles that had been released from the network for replication bind EB extensively, causing them, after isolation, to become highly supertwisted and to develop regions of left-handed Z-DNA (without EB, these circles are fully relaxed. In vivo, EB causes helix distortion of free minicircles, preventing replication initiation and resulting in kDNA loss and cell death. Unexpectedly, EB also kills dyskinetoplastic trypanosomes, lacking kDNA, by inhibiting nuclear replication. Since the effect on kDNA occurs at a >10-fold lower EB concentration than that on nuclear DNA, we conclude that minicircle replication initiation is likely EB's most vulnerable target, but the effect on nuclear replication may also contribute to cell killing.

  12. Inhalable Ipratropium Bromide Particle Engineering with Multicriteria Optimization.

    Science.gov (United States)

    Vinjamuri, Bhavani Prasad; Haware, Rahul V; Stagner, William C

    2017-08-01

    Spray-dried ipratropium bromide (IPB) microspheres for oral inhalation were engineered using Quality by Design. The interrogation of material properties, process parameters, and critical product quality attributes interplay enabled rational product design. A 2 7-3 screening design exhibited the Maillard reaction between L-leucine (LL) and lactose at studied outlet temperatures (OT) >130°C. A response surface custom design was used in conjunction with multicriteria optimization to determine the operating design space to achieve inhalable microparticles. Statistically significant predictive models were developed for volume median diameter (p = 0.0001, adjusted R 2   = 0.9938), span (p = 0.0278, adjusted R 2   = 0.7912), yield (p = 0.0020, adjusted R 2   = 0.9320), and OT (p = 0.0082, adjusted R 2   = 0.8768). An independent verification batch confirmed the model's predictive capability. The prediction and actual values were in good agreement. Particle size and span were 3.32 ± 0.09 μm and 1.71 ± 0.18, which were 4.7 and 5.3% higher than the predicted values. The process yield was 50.3%, compared to the predicted value of 65.3%. The OT was 100°C versus the predicted value of 105°C. The label strength of IPB microparticles was 99.0 to 105.9% w/w suggesting that enrichment occurred during the spray-drying process. The present study can be utilized to initiate the design of the first commercial IPB dry powder inhaler.

  13. Membrane electrodes for the determination of pyridostigmine bromide.

    Science.gov (United States)

    El-Kosasy, Amira M; Salem, Maissa Y; El-Bardicy, Mohamed G; Abd El-Rahman, Mohamed K

    2009-01-01

    Two pyridostigmine bromide (PB) selective electrodes were investigated with 2-nitrophenyl octyl ether as a plasticizer in a polymeric matrix of carboxylated polyvinyl chloride (PVC-COOH), based on the interaction between the drug solution and the dissociated COOH groups in the PVC-COOH. One of the sensors was fabricated by using PVC-COOH only as anionic site without incorporation of an ionophore (sensor 1). The second sensor was constructed by using 2-hydroxy propyl beta-cyclodextrin as an ionophore (sensor 2). Linear responses of PB within a concentration range of 10(-3)-10(-2) and 10(-5)-10(-2) M, with slopes of 51.9 +/- 0.31 and 56.7 +/- 0.40 mV/decade over pH range of 5-10 were obtained using sensors 2 and 1, respectively. The proposed method displayed useful analytical characteristics for determination of PB in tablets with average recoveries of 100.22 +/- 0.62, and 100.15 +/- 0.72, and in plasma with average recoveries of 99.14 +/- 1.19 and 99.79 +/- 0.72, for sensors 2 and 1, respectively. The utility of 2-hydroxy propyl beta-cyclodextrin as an ionophore has a significant influence on increasing both membrane sensitivity and selectivity of sensor 2 in comparison with sensor 1. The methods were also used to determine the intact drug in the presence of its degradate, and thus could be used as stability-indicating methods. The results obtained by the proposed procedures were statistically analyzed and compared with those obtained by the U.S. Pharmacopeia method. No significant difference for either accuracy or precision was observed.

  14. Fluorescence Decay Dynamics of Ethidium Bromide in Polymers

    International Nuclear Information System (INIS)

    Jee, Ah Young; Min Yung

    2010-01-01

    The fluorescence lifetimes of EB in five polymers covering LDPE, HDPE, PC, PS, and PAA were measured by picosecond time-correlated single photon counting. The lifetime change of EB has been previously described by hydrogen bonding ability. In this work, we have observed that the lifetime of EB depends strongly on the Young's modulus of medium. Thus, it is possible that the fluorescence decay dynamics of EB could be influenced by medium rigidity rather than hydrogen bonding ability in polymer. The medium influence on the fluorescence decay dynamics of ethidium bromide (EB) has been investigated in various environments. For example, Ohmstead and Kearns related the fluorescence lifetime of EB to the excited-state proton transfer process. In addition, they reported that the solvent viscosity plays a minor role in the excited state decay process of EB. Chirico et al. measured the fluorescence decay of EB as 1.7 ns in water and 6.5 ns in ethanol and concluded that hydrogen bonding ability is a key factor for the nonradiative relaxation. Pal et al. measured the fluorescence decay time of EB in acetone, acetonitrile, and their mixtures. They observed that the fluorescence decay processes were independent on the solvent polarity. These results show that the EB lifetime does not depend much on polarity or viscosity, but is mainly influenced by hydrogen bonding. Overall, EB is one of most widely used dyes for probing DNA. When EB is intercalated into the helical structure of DNA, a large increase in the fluorescence lifetime has been observed in comparison with water environment, and the fluorescence enhancement was attributed to the blocking of the excited-state proton transfer

  15. Stable room-temperature thallium bromide semiconductor radiation detectors

    Science.gov (United States)

    Datta, A.; Fiala, J.; Becla, P.; Motakef, Shariar

    2017-10-01

    Thallium bromide (TlBr) is a highly efficient ionic semiconductor with excellent radiation detection properties. However, at room temperature, TlBr devices polarize under an applied electric field. This phenomenon not only degrades the charge collection efficiency of the detectors but also promotes chemical reaction of the metal electrodes with bromine, resulting in an unstable electric field and premature failure of the device. This drawback has been crippling the TlBr semiconductor radiation detector technology over the past few decades. In this exhaustive study, this polarization phenomenon has been counteracted using innovative bias polarity switching schemes. Here the highly mobile Br- species, with an estimated electro-diffusion velocity of 10-8 cm/s, face opposing electro-migration forces during every polarity switch. This minimizes the device polarization and availability of Br- ions near the metal electrode. Our results indicate that it is possible to achieve longer device lifetimes spanning more than 17 000 h (five years of 8 × 7 operation) for planar and pixelated radiation detectors using this technique. On the other hand, at constant bias, 2500 h is the longest reported lifetime with most devices less than 1000 h. After testing several biasing switching schemes, it is concluded that the critical bias switching frequency at an applied bias of 1000 V/cm is about 17 μHz. Using this groundbreaking result, it will now be possible to deploy this highly efficient room temperature semiconductor material for field applications in homeland security, medical imaging, and physics research.

  16. Eudragit RS PO nanoparticles for sustained release of pyridostigmine bromide

    International Nuclear Information System (INIS)

    Hoobakht, Fatemeh; Ganji, Fariba; Vasheghani-Farahani, Ebrahim; Mousavi, Seyyed Mohammad

    2013-01-01

    Pyridostigmine bromide (PB) is an inhibitor of cholinesterase, which is used in the treatment of myasthenia gravis and administered for protection against exposure to toxic nerve agents. Tests were done to investigate prolonging the half-life of PB and improving its release behavior. PB was loaded in nanoparticles (NPs) of Eudragit RS PO (Eu-RS) prepared using the technique of quasi emulsion solvent diffusion. Variables of output power of the sonicator, bath temperature and mixing time, were chosen as the optimization factors to obtain the minimum sized NPs. In addition, emulsions were tested at different ratios of drug-to-polymer by dynamic light scattering to determine size and zeta potential of NPs. UV-spectroscopy was used to determine PB content of the NPs. Drug-loaded NPs were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectra. Results determined that mixing time had a significant impact on the size of Eu-RS NPs, but power output of sonicator and bath temperature had no significant effect. The particle size obtained at the optimum condition (power output of 70 W, bath temperature of 33 °C, and mixing time of 7 min) was less than 200 nm (optimum sizes were 138.9 and 179.5 nm for Eu-RS and PB-loaded Eu-RS NPs, respectively). The optimum PB-loaded Eu-RS NPs at the PB to Eu-RS weight ratio of 1–4 and 20 % of loaded PB released from the nanocarriers within 100 h

  17. Dicationic alkylammonium bromide gemini surfactants. Membrane perturbation and skin irritation.

    Directory of Open Access Journals (Sweden)

    João A S Almeida

    Full Text Available Dicationic alkylammonium bromide gemini surfactants represent a class of amphiphiles potentially effective as skin permeation enhancers. However, only a limited number of studies has been dedicated to the evaluation of the respective cytotoxicity, and none directed to skin irritation endpoints. Supported on a cell viability study, the cytotoxicity of gemini surfactants of variable tail and spacer length was assessed. For this purpose, keratinocyte cells from human skin (NCTC 2544 cell line, frequently used as a model for skin irritation, were employed. The impact of the different gemini surfactants on the permeability and morphology of model vesicles was additionally investigated by measuring the leakage of calcein fluorescent dye and analyzing the NMR spectra of ³¹P, respectively. Detail on the interaction of gemini molecules with model membranes was also provided by a systematic differential scanning calorimetry (DSC and molecular dynamics (MD simulation. An irreversible impact on the viability of the NCTC 2544 cell line was observed for gemini concentrations higher than 25 mM, while no cytotoxicity was found for any of the surfactants in a concentration range up to 10 mM. A higher cytotoxicity was also found for gemini surfactants presenting longer spacer and shorter tails. The same trend was obtained in the calorimetric and permeability studies, with the gemini of longest spacer promoting the highest degree of membrane destabilization. Additional structural and dynamical characterization of the various systems, obtained by ³¹P NMR and MD, provide some insight on the relationship between the architecture of gemini surfactants and the respective perturbation mechanism.

  18. Stable room-temperature thallium bromide semiconductor radiation detectors

    Directory of Open Access Journals (Sweden)

    A. Datta

    2017-10-01

    Full Text Available Thallium bromide (TlBr is a highly efficient ionic semiconductor with excellent radiation detection properties. However, at room temperature, TlBr devices polarize under an applied electric field. This phenomenon not only degrades the charge collection efficiency of the detectors but also promotes chemical reaction of the metal electrodes with bromine, resulting in an unstable electric field and premature failure of the device. This drawback has been crippling the TlBr semiconductor radiation detector technology over the past few decades. In this exhaustive study, this polarization phenomenon has been counteracted using innovative bias polarity switching schemes. Here the highly mobile Br− species, with an estimated electro-diffusion velocity of 10−8 cm/s, face opposing electro-migration forces during every polarity switch. This minimizes the device polarization and availability of Br− ions near the metal electrode. Our results indicate that it is possible to achieve longer device lifetimes spanning more than 17 000 h (five years of 8 × 7 operation for planar and pixelated radiation detectors using this technique. On the other hand, at constant bias, 2500 h is the longest reported lifetime with most devices less than 1000 h. After testing several biasing switching schemes, it is concluded that the critical bias switching frequency at an applied bias of 1000 V/cm is about 17 μHz. Using this groundbreaking result, it will now be possible to deploy this highly efficient room temperature semiconductor material for field applications in homeland security, medical imaging, and physics research.

  19. Eudragit RS PO nanoparticles for sustained release of pyridostigmine bromide

    Energy Technology Data Exchange (ETDEWEB)

    Hoobakht, Fatemeh; Ganji, Fariba, E-mail: fganji@modares.ac.ir; Vasheghani-Farahani, Ebrahim [Tarbiat Modares University, Biomedical Engineering Group, Chemical Engineering Department (Iran, Islamic Republic of); Mousavi, Seyyed Mohammad [Tarbiat Modares University, Biotechnology Group, Chemical Engineering Department (Iran, Islamic Republic of)

    2013-09-15

    Pyridostigmine bromide (PB) is an inhibitor of cholinesterase, which is used in the treatment of myasthenia gravis and administered for protection against exposure to toxic nerve agents. Tests were done to investigate prolonging the half-life of PB and improving its release behavior. PB was loaded in nanoparticles (NPs) of Eudragit RS PO (Eu-RS) prepared using the technique of quasi emulsion solvent diffusion. Variables of output power of the sonicator, bath temperature and mixing time, were chosen as the optimization factors to obtain the minimum sized NPs. In addition, emulsions were tested at different ratios of drug-to-polymer by dynamic light scattering to determine size and zeta potential of NPs. UV-spectroscopy was used to determine PB content of the NPs. Drug-loaded NPs were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectra. Results determined that mixing time had a significant impact on the size of Eu-RS NPs, but power output of sonicator and bath temperature had no significant effect. The particle size obtained at the optimum condition (power output of 70 W, bath temperature of 33 Degree-Sign C, and mixing time of 7 min) was less than 200 nm (optimum sizes were 138.9 and 179.5 nm for Eu-RS and PB-loaded Eu-RS NPs, respectively). The optimum PB-loaded Eu-RS NPs at the PB to Eu-RS weight ratio of 1-4 and 20 % of loaded PB released from the nanocarriers within 100 h.

  20. X-ray Crystal Structure, Raman Spectroscopy and Ab Initio Density Functional Theory Calculations on 1,1,3,3-Tetramethylguanidinium Bromide

    DEFF Research Database (Denmark)

    Berg, Rolf W.; Riisager, Anders; Nguyen van Buu, Olivier

    2010-01-01

    The salt 1,1,3,3-tetramethylguanidinium bromide, [((CH3)2N)2C=NH2]+Br- or [tmgH]Br, was found to melt at 135(5) °C, forming what may be referred to as a moderate temperature ionic liquid. The chemistry was studied and compared with the corresponding chloride compound. We present X-ray diffraction...... and Raman evidence to show that also the bromide salt contains dimeric ion pair “molecules” in the crystalline state and probably also in the liquid state. The structure of [tmgH]Br determined at 120(2) K was found to be monoclinic, space group P21/n, with a = 7.2072(14), b = 13.335(3), c = 9.378(2) Å, beta......, for example, a characteristic strong band at 2229 cm-1. This band was interpreted by some of us to show that the [tmgH]Cl gas phase should consist of monomeric ion pair “molecules” held together by a single N-H+ · · · Cl- hydrogen bond, the stretching vibration of which should be causing the band, based on ab...

  1. Chemical Dynamics and Critical Phenomena: Electrical Conductivity and Reactivity of Benzyl Bromide in Triethylamine+Water Near its Consolute Point

    Science.gov (United States)

    Specker, Christopher D.; Ellis, Joel M.; Baird, James K.

    2007-06-01

    The binary liquid mixture of triethylamine+water has a lower consolute point at a critical composition of 32.27mass% triethylamine. Starting at a temperature within the one-phase region, the electrical conductivity of a sample of this mixture was measured and found to increase smoothly with increasing temperature before falling sharply at 291.24K (18.09°C). Since opalescence was visible at this temperature, it was identified with the critical solution temperature of the binary mixture. A solution of 90 μL of benzyl bromide dissolved in 90mL of 32.27mass% triethylamine+water was prepared, and the resulting Menschutkin reaction between benzyl bromide and triethylamine was allowed to come to equilibrium. The electrical conductivity of this equilibrium mixture was measured in the one-phase region and was found to increase smoothly with increasing temperature before rising sharply at 291.55K (18.40°C). This temperature was identified as the critical temperature of the ternary. The rate of approach of the ternary mixture to chemical equilibrium was also measured and shown to be governed by a first-order rate law. The temperature dependence of the rate coefficient followed the Arrhenius equation up to a temperature of about 290.74K (17.59°C). Above this temperature, the rate coefficient fell by as much as 22% below the value predicted by extrapolation of the Arrhenius equation. This suppression in the rate reaction in the vicinity of the critical temperature can be interpreted as evidence for the existence of critical slowing down.

  2. 2,6-Bis(oxazolinyl)phenylnickel(II) Bromide and 2,6-Bis(ketimine)phenylnickel(II) Bromide: Synthesis, Structural Features, and Redox Properties

    NARCIS (Netherlands)

    Stol, M.; Snelders, D.J.M.|info:eu-repo/dai/nl/304836257; Godbole, M.D.; Havenith, R.W.A.|info:eu-repo/dai/nl/205279546; Haddleton, D.M.; Clarkson, G.; Lutz, M.|info:eu-repo/dai/nl/304828971; Spek, A.L.|info:eu-repo/dai/nl/156517566; van Klink, G.P.M.|info:eu-repo/dai/nl/170637964; van Koten, G.|info:eu-repo/dai/nl/073839191

    2007-01-01

    2,6-Bis(oxazolinyl)phenylnickel bromide complexes [NiBr(R,R'-Phebox)] (2) were synthesized via two synthetic routes (A and B). In route A, selective bis-ortho lithiation of [R,R'-PheboxBr], followed by a transmetalation reaction with [NiBr2(PEt3)2], yielded not only complexes 2 with an

  3. Quasi-Chemical PC-SAFT: An Extended Perturbed Chain-Statistical Associating Fluid Theory for Lattice-Fluid Mixtures.

    Science.gov (United States)

    Parvaneh, Khalil; Shariati, Alireza

    2017-09-07

    In this study, a new modification of the perturbed chain-statistical associating fluid theory (PC-SAFT) has been proposed by incorporating the lattice fluid theory of Guggenheim as an additional term to the original PC-SAFT terms. As the proposed model has one more term than the PC-SAFT, a new mixing rule has been developed especially for the new additional term, while for the conventional terms of the PC-SAFT, the one-fluid mixing rule is used. In order to evaluate the proposed model, the vapor-liquid equilibria were estimated for binary CO 2 mixtures with 16 different ionic liquids (ILs) of the 1-alkyl-3-methylimidazolium family with various anions consisting of bis(trifluoromethylsulfonyl) imide, hexafluorophosphate, tetrafluoroborate, and trifluoromethanesulfonate. For a comprehensive comparison, three different modes (different adjustable parameters) of the proposed model were compared with the conventional PC-SAFT. Results indicate that the proposed modification of the PC-SAFT EoS is generally more reliable with respect to the conventional PC-SAFT in all the three proposed modes of vapor-liquid equilibria, giving good agreement with literature data.

  4. Residential proximity to methyl bromide use and birth outcomes in an agricultural population in California.

    Science.gov (United States)

    Gemmill, Alison; Gunier, Robert B; Bradman, Asa; Eskenazi, Brenda; Harley, Kim G

    2013-06-01

    Methyl bromide, a fungicide often used in strawberry cultivation, is of concern for residents who live near agricultural applications because of its toxicity and potential for drift. Little is known about the effects of methyl bromide exposure during pregnancy. We investigated the relationship between residential proximity to methyl bromide use and birth outcomes. Participants were from the CHAMACOS (Center for the Health Assessment of Mothers and Children of Salinas) study (n = 442), a longitudinal cohort study examining the health effects of environmental exposures on pregnant women and their children in an agricultural community in northern California. Using data from the California Pesticide Use Reporting system, we employed a geographic information system to estimate the amount of methyl bromide applied within 5 km of a woman's residence during pregnancy. Multiple linear regression models were used to estimate associations between trimester-specific proximity to use and birth weight, length, head circumference, and gestational age. High methyl bromide use (vs. no use) within 5 km of the home during the second trimester was negatively associated with birth weight (β = -113.1 g; CI: -218.1, -8.1), birth length (β = -0.85 cm; CI: -1.44, -0.27), and head circumference (β = -0.33 cm; CI: -0.67, 0.01). These outcomes were also associated with moderate methyl bromide use during the second trimester. Negative associations with fetal growth parameters were stronger when larger (5 km and 8 km) versus smaller (1 km and 3 km) buffer zones were used to estimate exposure. Residential proximity to methyl bromide use during the second trimester was associated with markers of restricted fetal growth in our study.

  5. Fluorometric determination of ethidium bromide efflux kinetics in Escherichia coli

    Directory of Open Access Journals (Sweden)

    Monteiro Gabriel A

    2009-10-01

    Full Text Available Abstract Background Efflux pump activity has been associated with multidrug resistance phenotypes in bacteria, compromising the effectiveness of antimicrobial therapy. The development of methods for the early detection and quantification of drug transport across the bacterial cell wall is a tool essential to understand and overcome this type of drug resistance mechanism. This approach was developed to study the transport of the efflux pump substrate ethidium bromide (EtBr across the cell envelope of Escherichia coli K-12 and derivatives, differing in the expression of their efflux systems. Results EtBr transport across the cell envelope of E. coli K-12 and derivatives was analysed by a semi-automated fluorometric method. Accumulation and efflux of EtBr was studied under limiting energy supply (absence of glucose and low temperature and in the presence and absence of the efflux pump inhibitor, chlorpromazine. The bulk fluorescence variations were also observed by single-cell flow cytometry analysis, revealing that once inside the cells, leakage of EtBr does not occur and that efflux is mediated by active transport. The importance of AcrAB-TolC, the main efflux system of E. coli, in the extrusion of EtBr was evidenced by comparing strains with different levels of AcrAB expression. An experimental model was developed to describe the transport kinetics in the three strains. The model integrates passive entry (influx and active efflux of EtBr, and discriminates different degrees of efflux between the studied strains that vary in the activity of their efflux systems, as evident from the calculated efflux rates: = 0.0173 ± 0.0057 min-1; = 0.0106 ± 0.0033 min-1; and = 0.0230 ± 0.0075 min-1. Conclusion The combined use of a semi-automated fluorometric method and an experimental model allowed quantifying EtBr transport in E. coli strains that differ in their overall efflux activity. This methodology can be used for the early detection of differences in

  6. Activity of aminotransferases in organs of rats during hypoxia of enclosed space of the action of thiamine bromide

    Directory of Open Access Journals (Sweden)

    Сніжана Сергіївна Чернадчук

    2015-05-01

    Full Text Available It is studied an aminotransferase activity during injection of thiamin bromide in rat tissues in normal and hypoxic enclosed space. After injection of thiamine bromide we have set reduction of AST and ALT activity, relative to control, except by the brain tissue, where there was an increase of investigated indicators. The decrease of activity of the investigated elements is occurred in animals which before hypoxia were injection of thiamine bromide

  7. The salting-out effect and phase separation in aqueous solutions of tri-sodium citrate and 1-butyl-3-methylimidazolium bromide

    International Nuclear Information System (INIS)

    Sadeghi, Rahmat; Golabiazar, Roonak; Shekaari, Hemayat

    2010-01-01

    The aim of this work is to obtain further evidence about the salting-out effect produced by the addition of tri-sodium citrate to aqueous solutions of water miscible ionic liquid 1-butyl-3-methylimidazolium bromide ([C 4 mim][Br]) by evaluating the effect of tri-sodium citrate on the thermodynamic properties of aqueous solutions of this ionic liquid. Experimental measurements of density and sound velocity at different temperatures ranging from (288.15 to 308.15) K, the refractive index at 308.15 K and the liquid-liquid phase diagram at different temperatures ranging from (288.15 to 338.15) K for aqueous solutions containing 1-butyl-3-methylimidazolium bromide ([C 4 mim][Br]) and tri-sodium citrate (Na 3 Cit) are taken. The apparent molar volume of transfer of [C 4 mim][Br] from water to aqueous solutions of Na 3 Cit have positive values and it increases by increasing salt molality. Although at high IL molality, the apparent molar isentropic compressibility shows similar behaviour with that of the apparent molar volume. However at low concentrations of IL, the apparent molar isentropic compressibility of transfer of [C 4 mim][Br] from water to aqueous solutions of Na 3 Cit have negative values. The effects of temperature and the addition of Na 3 Cit and [C 4 mim][Br] on the liquid-liquid phase diagram of the investigated system have been studied. It was found that an increase in temperature caused the expansion of the one-phase region. The presence of Na 3 Cit triggers a salting-out effect, leading to significant upward shifts of the liquid-liquid de-mixing temperatures of the system. The effect of temperature on the phase-forming ability in the system investigated has been studied based on a salting-out coefficient obtained from fitting the binodal values to a Setschenow-type equation for each temperature. Based on cloud point values, the energetics of the clouding process have been estimated and it was found that both of entropy and enthalpy are the driving forces

  8. The salting-out effect and phase separation in aqueous solutions of tri-sodium citrate and 1-butyl-3-methylimidazolium bromide

    Energy Technology Data Exchange (ETDEWEB)

    Sadeghi, Rahmat, E-mail: rsadeghi@uok.ac.i [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of); Golabiazar, Roonak [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of); Shekaari, Hemayat [Department of Chemistry, Faculty of Science, University of Mohaghegh Ardabili, Ardabil (Iran, Islamic Republic of)

    2010-04-15

    The aim of this work is to obtain further evidence about the salting-out effect produced by the addition of tri-sodium citrate to aqueous solutions of water miscible ionic liquid 1-butyl-3-methylimidazolium bromide ([C{sub 4}mim][Br]) by evaluating the effect of tri-sodium citrate on the thermodynamic properties of aqueous solutions of this ionic liquid. Experimental measurements of density and sound velocity at different temperatures ranging from (288.15 to 308.15) K, the refractive index at 308.15 K and the liquid-liquid phase diagram at different temperatures ranging from (288.15 to 338.15) K for aqueous solutions containing 1-butyl-3-methylimidazolium bromide ([C{sub 4}mim][Br]) and tri-sodium citrate (Na{sub 3}Cit) are taken. The apparent molar volume of transfer of [C{sub 4}mim][Br] from water to aqueous solutions of Na{sub 3}Cit have positive values and it increases by increasing salt molality. Although at high IL molality, the apparent molar isentropic compressibility shows similar behaviour with that of the apparent molar volume. However at low concentrations of IL, the apparent molar isentropic compressibility of transfer of [C{sub 4}mim][Br] from water to aqueous solutions of Na{sub 3}Cit have negative values. The effects of temperature and the addition of Na{sub 3}Cit and [C{sub 4}mim][Br] on the liquid-liquid phase diagram of the investigated system have been studied. It was found that an increase in temperature caused the expansion of the one-phase region. The presence of Na{sub 3}Cit triggers a salting-out effect, leading to significant upward shifts of the liquid-liquid de-mixing temperatures of the system. The effect of temperature on the phase-forming ability in the system investigated has been studied based on a salting-out coefficient obtained from fitting the binodal values to a Setschenow-type equation for each temperature. Based on cloud point values, the energetics of the clouding process have been estimated and it was found that both of

  9. Ethidium bromide resistance of L929 cells is accompanied by regular changes in karotype structure

    International Nuclear Information System (INIS)

    Grinchuk, T.M.; Novikova, I.Yu.; Sorokina, E.A.; Sal'nikov, K.V.

    1988-01-01

    Using the method of differential staining of chromosomes for G-bands a comparative karyological analysis of line L 929 mouse cells has been conducted, after the L 929 cells had been sequentially selected for resistance to ethidium bromide at concentrations of 1, 10, 25, and 50 μg/ml and had retained these levels of resistance for a number of cell generations. It was found that the resistant variants exhibited certain karyotypic changes. Only thirteen of the thirty six marker chromosomes typical of the original ethidium bromide-sensitive cells were preserved. Sixteen of the markers were specific for the resistant variants. The changes detected arose at the initial selection stage and were preserved unaltered as the concentration of the toxin was raised. The detection of similar karyotypic changes in cells of clone L 929 of independent origin selected for resistance of 3 μg/ml of ethidium bromide and also in cells of the clone selected for resistance to 25 μg/ml of ethidium bromide and studied previously by the present authors suggests that these changes are universal for L 929 cells resistant to ethidium bromide

  10. Profile of aclidinium bromide in the treatment of chronic obstructive pulmonary disease

    Directory of Open Access Journals (Sweden)

    Sims MW

    2011-09-01

    Full Text Available Michael W Sims, Reynold A Panettieri, Jr. Pulmonary, Allergy, and Critical Care Division, Airways Biology Initiative, Department of Medicine, University of Pennsylvania School of Medicine, Philadelphia, PA, USA Abstract: Bronchodilators provide the mainstay of pharmacologic therapy for chronic obstructive pulmonary disease (COPD, and anticholinergic bronchodilators, in particular, appear to be the most effective. There are currently two anticholinergic agents available in the US for the treatment of COPD (ipratropium bromide and tiotropium bromide, but several others are in various stages of development. Aclidinium bromide, a novel, long-acting, anticholinergic bronchodilator, is currently in Phase III trials for the management of COPD. Available evidence suggests that aclidinium is a safe and well tolerated drug with a relatively rapid onset and a sufficient duration of action to provide once-daily dosing. This article will provide a pharmacologic profile of aclidinium bromide and review the preclinical and clinical studies evaluating its safety and efficacy in the treatment of COPD. Keywords: aclidinium bromide, bronchodilators, pulmonary disease, chronic obstructive, muscarinic antagonists, pharmacokinetics, pharmacology

  11. Pharmacodynamic Comparison of Rocuronium Bromide between Patients from the Plateau Area and from the Plain Area.

    Science.gov (United States)

    Xie, Min; Huang, Jianxin; Li, Peng; Ou, Zhiyan; Hou, Jing

    2016-06-23

    We aimed to conduct a pharmacodynamic comparison of rocuronium bromide between patients from the plateau area and from the plain area. A total of 104 patients who received laparoscopic cholecystectomy in Sichuan Provincial People's Hospital and Aba Autonomous Prefecture People's Hospital from October 2015 to December 2015 were included in this study. Among them, 46 patients were from the plateau area and 58 were from the plain area. Both groups received total intravenous anesthesia (TIVA) with a dose of 0.6mg/kg rocuronium bromide during induction. In the meantime, neuromuscular block was monitored using a train-of-four (TOF) stimulation mode. The onset time (time to achieve the lowest TOF value after the injection of rocuronium bromide), duration of maximal neuromuscular block (duration of lowest T1 value), time to 25% recovery, time to 75% recovery, recovery index (time from 25% recovery to 75% recovery), time to extubation, length of stay in Post Anesthesia Care Unit (PACU) and muscle strength upon PACU discharge were all recorded. The onset time, time to 25% recovery, time to 75% recovery and time to extubation were all significantly prolonged in patients from the plateau area after receiving one single dose of rocuronium bromide (P0.05). Compared to patients from the plain area, patients from the plateau area showed prolonged onset time of rocuronium bromide, reduced metabolic capabilities and longer duration of muscular relaxation. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

  12. Utility of bromide and heat tracers for aquifer characterization affected by highly transient flow conditions

    Science.gov (United States)

    Ma, Rui; Zheng, Chunmiao; Zachara, John M.; Tonkin, Matthew

    2012-08-01

    A tracer test using both bromide and heat tracers conducted at the Integrated Field Research Challenge site in Hanford 300 Area (300A), Washington, provided an instrument for evaluating the utility of bromide and heat tracers for aquifer characterization. The bromide tracer data were critical to improving the calibration of the flow model complicated by the highly dynamic nature of the flow field. However, most bromide concentrations were obtained from fully screened observation wells, lacking depth-specific resolution for vertical characterization. On the other hand, depth-specific temperature data were relatively simple and inexpensive to acquire. However, temperature-driven fluid density effects influenced heat plume movement. Moreover, the temperature data contained "noise" caused by heating during fluid injection and sampling events. Using the hydraulic conductivity distribution obtained from the calibration of the bromide transport model, the temperature depth profiles and arrival times of temperature peaks simulated by the heat transport model were in reasonable agreement with observations. This suggested that heat can be used as a cost-effective proxy for solute tracers for calibration of the hydraulic conductivity distribution, especially in the vertical direction. However, a heat tracer test must be carefully designed and executed to minimize fluid density effects and sources of noise in temperature data. A sensitivity analysis also revealed that heat transport was most sensitive to hydraulic conductivity and porosity, less sensitive to thermal distribution factor, and least sensitive to thermal dispersion and heat conduction. This indicated that the hydraulic conductivity remains the primary calibration parameter for heat transport.

  13. A novel explicit approach to model bromide and pesticide transport in soils containing macropores

    Science.gov (United States)

    Klaus, J.; Zehe, E.

    2011-01-01

    The present study tests whether an explicit treatment of worm burrows is feasible for simulating water flow, bromide and pesticide transport in structured heterogeneous soils. The essence is to represent worm burrows as morphologically connected paths of low flow resistance in the spatially highly resolved model domain. A recent Monte Carlo study (Klaus and Zehe, 2010) revealed that this approach allowed successful reproduction of tile drain event discharge recorded during an irrigation experiment at a tile drained field site. However, several "hillslope architectures" that were all consistent with the available extensive data base allowed a good reproduction of tile drain flow response. Our second objective was thus to find out whether this "equifinality" in spatial model setups may be reduced when including bromide tracer data in the model falsification process. We thus simulated transport of bromide and Isoproturon (IPU) for the 13 spatial model setups, which performed best with respect to reproduce tile drain event discharge, without any further calibration. All model setups allowed a very good prediction of the temporal dynamics of cumulated bromide leaching into the tile drain, while only four of them matched the accumulated water balance and accumulated bromide loss into the tile drain. The number of behavioural model architectures could thus be reduced to four. One of those setups was used for simulating transport of IPU, using different parameter combinations to characterise adsorption according to the Footprint data base. Simulations could, however, only reproduce the observed leaching behaviour, when we allowed for retardation coefficients that were very close to one.

  14. Rocuronium Bromide Inhibits Inflammation and Pain by Suppressing Nitric Oxide Production and Enhancing Prostaglandin E2 Synthesis in Endothelial Cells.

    Science.gov (United States)

    Baek, Sang Bin; Shin, Mal Soon; Han, Jin Hee; Moon, Sang Woong; Chang, Boksoon; Jeon, Jung Won; Yi, Jae Woo; Chung, Jun Young

    2016-12-01

    Rocuronium bromide is a nondepolarizing neuromuscular blocking drug and has been used as an adjunct for relaxation or paralysis of the skeletal muscles, facilitation of endotracheal intubation, and improving surgical conditions during general anesthesia. However, intravenous injection of rocuronium bromide induces injection pain or withdrawal movement. The exact mechanism of rocuronium bromide-induced injection pain or withdrawal movement is not yet understood. We investigated whether rocuronium bromide treatment is involved in the induction of inflammation and pain in vascular endothelial cells. For this study, calf pulmonary artery endothelial (CPAE) cells were used, and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay, Western blot, nitric oxide detection, and prostaglandin E 2 immunoassay were conducted. Rocuronium bromide treatment inhibited endothelial nitric oxide synthase and suppressed nitric oxide production in CPAE cells. Rocuronium bromide activated cyclooxygenase-2, inducible nitric oxide synthase and increased prostaglandin E 2 synthesis in CPAE cells. Rocuronium bromide induced inflammation and pain in CPAE cells. Suppressing nitric oxide production and enhancing prostaglandin E 2 synthesis might be associated with rocuronium bromide-induced injection pain or withdrawal movement.

  15. Experimental determination and prediction of phase behavior for 1-butyl-3-methylimidazolium nonafluorobutyl sulfonate and carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Soon Kang; Park, YoonKook [Hongik University, Sejong (Korea, Republic of); Pore, Dattaprasad Marutrao [Shivaji University, Kolhapur (India)

    2014-09-15

    The vapor-liquid equilibrium of the binary system CO{sub 2}+1-butyl-3-methylimidazolium nonafluorobutyl sulfonate ([BMIM][NfO]) was measured over a temperature range of 298.2-323.2 K at intervals of 5.0 K for CO{sub 2} mole fraction ranging from 0.137 to 0.900 using a high-pressure variable-volume view cell. The Peng-Robinson equation of state was then applied with two-parameter mixing rules over the same range and the results compared with the experimentally obtained data. Increasing the alkyl chain length in perfluorinated sulfonate from methyl to butyl markedly increased the CO{sub 2} solubility. To investigate the effect of the number of fluorine atoms in the anion on the phase behavior of imidazolium based ionic liquid, these experimental results were then compared with those reported in previous experimental studies of 1-alkyl-3-methylimidazolium cations and with modeling data. It looks likely that both the number of fluorine atoms in the anion and the presence of S=O groups play an important role in designing CO{sub 2}-philic molecules.

  16. Competition between organics and bromide at the aqueous solution-air interface as seen from ozone uptake kinetics and X-ray photoelectron spectroscopy.

    Science.gov (United States)

    Lee, Ming-Tao; Brown, Matthew A; Kato, Shunsuke; Kleibert, Armin; Türler, Andreas; Ammann, Markus

    2015-05-14

    A more detailed understanding of the heterogeneous chemistry of halogenated species in the marine boundary layer is required. Here, we studied the reaction of ozone (O3) with NaBr solutions in the presence and absence of citric acid (C6H8O7) under ambient conditions. Citric acid is used as a proxy for oxidized organic material present at the ocean surface or in sea spray aerosol. On neat NaBr solutions, the observed kinetics is consistent with bulk reaction-limited uptake, and a second-order rate constant for the reaction of O3 + Br(-) is 57 ± 10 M(-1) s(-1). On mixed NaBr-citric acid aqueous solutions, the uptake kinetics was faster than that predicted by bulk reaction-limited uptake and also faster than expected based on an acid-catalyzed mechanism. X-ray photoelectron spectroscopy (XPS) on a liquid microjet of the same solutions at 1.0 × 10(-3)-1.0 × 10(-4) mbar was used to obtain quantitative insight into the interfacial composition relative to that of the bulk solutions. It revealed that the bromide anion becomes depleted by 30 ± 10% while the sodium cation gets enhanced by 40 ± 20% at the aqueous solution-air interface of a 0.12 M NaBr solution mixed with 2.5 M citric acid in the bulk, attributed to the role of citric acid as a weak surfactant. Therefore, the enhanced reactivity of bromide solutions observed in the presence of citric acid is not necessarily attributable to a surface reaction but could also result from an increased solubility of ozone at higher citric acid concentrations. Whether the acid-catalyzed chemistry may have a larger effect on the surface than in the bulk to offset the effect of bromide depletion also remains open.

  17. Methyl bromide: ocean sources, ocean sinks, and climate sensitivity.

    Science.gov (United States)

    Anbar, A D; Yung, Y L; Chavez, F P

    1996-03-01

    The oceans play an important role in the geochemical cycle of methyl bromide (CH3Br), the major carrier of O3-destroying bromine to the stratosphere. The quantity of CH3Br produced annually in seawater is comparable to the amount entering the atmosphere each year from natural and anthropogenic sources. The production mechanism is unknown but may be biological. Most of this CH3Br is consumed in situ by hydrolysis or reaction with chloride. The size of the fraction which escapes to the atmosphere is poorly constrained; measurements in seawater and the atmosphere have been used to justify both a large oceanic CH3Br flux to the atmosphere and a small net ocean sink. Since the consumption reactions are extremely temperature-sensitive, small temperature variations have large effects on the CH3Br concentration in seawater, and therefore on the exchange between the atmosphere and the ocean. The net CH3Br flux is also sensitive to variations in the rate of CH3Br production. We have quantified these effects using a simple steady state mass balance model. When CH3Br production rates are linearly scaled with seawater chlorophyll content, this model reproduces the latitudinal variations in marine CH3Br concentrations observed in the east Pacific Ocean by Singh et al. [1983] and by Lobert et al. [1995]. The apparent correlation of CH3Br production with primary production explains the discrepancies between the two observational studies, strengthening recent suggestions that the open ocean is a small net sink for atmospheric CH3Br, rather than a large net source. The Southern Ocean is implicated as a possible large net source of CH3Br to the atmosphere. Since our model indicates that both the direction and magnitude of CH3Br exchange between the atmosphere and ocean are extremely sensitive to temperature and marine productivity, and since the rate of CH3Br production in the oceans is comparable to the rate at which this compound is introduced to the atmosphere, even small

  18. Effects of caffeine on cleavage delay of sea urchin eggs induced by ethidium bromide or puromycin

    International Nuclear Information System (INIS)

    Kimura, Hiroshi

    1975-01-01

    The mitotic delay was induced when sea urchin eggs were treated with either ethidium bromide or puromycin, as observed with eggs fertilized with x- or UV-irradiated sperm. Treatment of these eggs with caffeine during the period of early prophase block resulted in the reduction of the mitotic delay. Protein synthesis of these eggs was not affected by x-irradiation but inhibited by ethidium bromide or puromycin. Caffeine was almost ineffective in changing the protein synthesis of eggs inseminated with x-irradiated sperm or treated with ethidium bromide. These facts mean that additive synthesis of protein is not required for the reduction by caffeine of the mitotic delay. Some role of protein synthesis in the reduction by caffeine of the cleavage delay is not excluded for puromycin treated eggs, since caffeine counteracted the inhibitory effect of puromycin on protein synthesis. (author)

  19. Temporary diplopia upon hyoscine-N-butyl bromide administration: case report

    Directory of Open Access Journals (Sweden)

    Migliorini R

    2013-05-01

    Full Text Available R Migliorini, R Malagola, M Mafrici, R Spena, L ArricoDepartment of Sense Organs, University of Rome "La Sapienza", Rome, ItalyAbstract: Hyoscine-N-butyl bromide is a widely used antispasmodic belonging to the belladonna alkaloid class of semisynthetic quaternary ammonium compounds. These compounds exert a spasmolytic action on the smooth muscles of the bile-gastrointestinal tract, genitourinary tract, salivary glands (xerostomia, and also on the visual apparatus – in particular, the irido-ciliary complex. As a consequence, they provoke collateral effects such as mydriasis and accommodation disturbances. We report the case of a 23-year-old woman who complained of not only "dry mouth" but also "cloudy vision" and a "diplopia", both of temporary type, 2 hours after oral administration of hyoscine-N-butyl bromide.Keywords: hyoscine-N-butyl bromide, accommodation disorders, temporary diplopia, fusion alteration, vertical strabismus

  20. Chloride/bromide ratios in leachate derived from farm-animal waste

    International Nuclear Information System (INIS)

    Hudak, P.F.

    2003-01-01

    Results have important implications for identifying animal sources of contaminated groundwater. - Ratios of conservative chemicals have been used to identify sources of groundwater contamination. While chloride/bromide ratios have been reported for several common sources of groundwater contamination, little work has been done on leachate derived from farm-animal waste. In this study, chloride/bromide ratios were measured in leachate derived from longhorn-cattle, quarter-horse, and pygme-goat waste at a farm in Abilene, Texas, USA. (Minimum, median, and maximum) chloride/bromide ratios of (66.5, 85.6, and 167), (119, 146, and 156), and (35.4, 57.8, and 165) were observed for cattle, horses, and goats, respectively. These ratios are below typical values for domestic wastewater and within the range commonly observed for oilfield brine. Results of this study have important implications for identifying sources of contaminated groundwater in settings with significant livestock and/or oil production

  1. Iodate and iodo-trihalomethane formation during chlorination of iodide-containing waters: role of bromide.

    Science.gov (United States)

    Criquet, Justine; Allard, Sebastien; Salhi, Elisabeth; Joll, Cynthia A; Heitz, Anna; von Gunten, Urs

    2012-07-03

    The kinetics of iodate formation is a critical factor in mitigation of the formation of potentially toxic and off flavor causing iodoorganic compounds during chlorination. This study demonstrates that the formation of bromine through the oxidation of bromide by chlorine significantly enhances the oxidation of iodide to iodate in a bromide-catalyzed process. The pH-dependent kinetics revealed species specific rate constants of k(HOBr + IO(-)) = 1.9 × 10(6) M(-1) s(-1), k(BrO(-) + IO(-)) = 1.8 × 10(3) M(-1) s(-1), and k(HOBr + HOI) < 1 M(-1) s(-1). The kinetics and the yield of iodate formation in natural waters depend mainly on the naturally occurring bromide and the type and concentration of dissolved organic matter (DOM). The process of free chlorine exposure followed by ammonia addition revealed that the formation of iodo-trihalomethanes (I-THMs), especially iodoform, was greatly reduced by an increase of free chlorine exposure and an increase of the Br(-)/I(-) ratio. In water from the Great Southern River (with a bromide concentration of 200 μg/L), the relative I-incorporation in I-THMs decreased from 18 to 2% when the free chlorine contact time was increased from 2 to 20 min (chlorine dose of 1 mg Cl(2)/L). This observation is inversely correlated with the conversion of iodide to iodate, which increased from 10 to nearly 90%. Increasing bromide concentration also increased the conversion of iodide to iodate: from 45 to nearly 90% with a bromide concentration of 40 and 200 μg/L, respectively, and a prechlorination time of 20 min, while the I-incorporation in I-THMs decreased from 10 to 2%.

  2. Irradiation as a disinfestation method - update on methyl bromide phase out, regulatory action and emerging opportunities

    International Nuclear Information System (INIS)

    Marcotte, Michelle

    1998-01-01

    Methyl bromide (MeBr), is the most widely used agricultural fumigant in the world for the control of pests and plant diseases. It is used to control pests and diseases in food, agricultural and forestry commodities after harvest, before or during storage or transportation and/or at time of import to control quarantine or storage pests. Knowing MeBr will be phased out has spurred a search for alternative treatments and products, and has placed pressure on regulatory authorities to approve alternatives. Some of methyl bromide use could be replaced with irradiation. Methyl bromide is also used for soil and structural fumigation, and although there is some use of irradiation for packaged soil or greenhouse products, in general, these uses can not be replaced by irradiation. Some radiation processing facilities have either seen increased business to disinfest commodities, or have experienced more inquiries for service. There are many other processes and products competing for this market and irradiation will not win its share of the business without an improved regulatory picture, improved marketing to methyl bromide users and improved information to answer questions from commodity sectors. The United Nations Environment Program - Methyl Bromide Technical Options Committee (MBTOC) provides a venue for the publication or information about the use and availability of irradiation as an alternative to methyl bromide. It provides the technical base to the Montreal Protocol contributing to the setting of phase out dates; this committee is actively researching and assessing all alternatives and needs information about irradiation. The author is a member of the MBTOC committee

  3. Halide-mediated regioselective 6-O-glycosylation of unprotected hexopyranosides with perbenzylated glycosyl bromide donors

    DEFF Research Database (Denmark)

    Niedbal, Dominika Alina; Madsen, Robert

    2016-01-01

    The regio- and stereoselective glycosylation at the 6-position in 2,3,4,6-unprotected hexopyranosides has been investigated with dibutyltin oxide as the directing agent. Perbenzylated hexopyranosyl bromides were employed as the donors and the glycosylations were promoted by tetrabutylammonium...... bromide. The couplings were completely selective for both glucose and galactose donors and acceptors as long as the stannylene acetal of the acceptor was soluble in dichloromethane. This gave rise to a number of 1,2-cis-linked disaccharides in reasonable yields. Mannose donors and acceptors, on the other...

  4. Kinetics of bromide catalysed oxidation of dextrose by cerium (IV) in aqueous sulphuric acid solution

    International Nuclear Information System (INIS)

    Sharma, J.; Sah, M.P.

    1994-01-01

    Kinetics of bromide catalysed oxidation of dextrose by Ce IV in aqueous sulphuric acid medium show first order dependence each in dextrose and cerium(IV). The reaction rate decreases on increasing the concentration of hydrogen ion. The increase in [HSO 4 - ] or [SO 4 2- ] decreases the rate. The bromide ion shows positive catalytic effect on the reaction rate. The value of activation energy has been calculated and a suitable mechanism confirming to the kinetic data is proposed. (author). 3 refs., 3 tabs

  5. Well-Defined Copper(I) Fluoroalkoxide Complexes for Trifluoroethoxylation of Aryl and Heteroaryl Bromides

    KAUST Repository

    Huang, Ronglu

    2015-03-17

    © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. Copper(I) fluoroalkoxide complexes bearing dinitrogen ligands were synthesized and the structure and reactivity of the complexes toward trifluoroethoxylation, pentafluoropropoxylation, and tetrafluoropropoxylation of aryl and heteroaryl bromides were investigated. Efficiency drive: A series of copper(I) fluoroalkoxide complexes bearing N,N ligands have been prepared and structurally characterized. These well-defined complexes serve as efficient reagents for the fluoroalkoxylation of aryl and heteroaryl bromides to produce a wide range of trifluoroethyl, pentafluoropropyl, and tetrafluoropropyl (hetero)aryl ethers in good to excellent yields.

  6. COMPARISON OF ROCURONIUM BROMIDE AND SUCCINYLCHOLINE CHLORIDE FOR USE DURING RAPID SEQUENCE INTUBATION IN ADULTS

    Directory of Open Access Journals (Sweden)

    Ch. Penchalaiah

    2015-08-01

    Full Text Available BACKGROUND AND OBJECTIVE : The goal of rapid sequence intubation is to secure the patients airway smoothly and quickly, minimizing the chances of regurgitation and aspiration of gastric contents. Traditionally succinylcholine chloride has been the neuromuscular blocking drug of choi ce for use in rapid sequence intubation because of its rapid onset of action and profound relaxation. Succinylcholine chloride remains unsurpassed in providing ideal intubating conditions. However the use of succinylcholine chloride is associated with many side effects like muscle pain, bradycardia, hyperkalaemia and rise in intragastric and intraocular pressure. Rocuronium bromide is the only drug currently available which has the rapidity of onset of action like succinylcholine chloride. Hence the present study was undertaken to compare rocuronium bromide with succinylcholine chloride for use during rapid sequence intubation in adult patients. METHODOLOGY : The study population consisted of 90 patients aged between 18 - 60 years posted for various elective su rgeries requiring general anaesthesia . S tudy population was randomly divided into 3 groups with 30 patients in each sub group. 1. Group I : Intubated with 1 mg kg - 1 of succinylcholine chloride (n=30 . 2. Grou p II : Intubated with rocuronium bromide 0.6 mg kg - 1 (n=30 . 3. Group III : Intubated with rocuronium bromide 0.9 mg kg - 1 (n=30 . Intubating conditions were assessed at 60 seconds based on the scale adopted by Toni Magorian et al. 1993. The haemodynamic para meters in the present study were compared using p - value obtained from student t - test . RESULTS : It was noted that succinylcholine chloride 1 mg kg - 1 body weight produced excellent intubating conditions in all patients. Rocuronium bromide 0.6 mg kg - 1 body we ight produced excellent intubating conditions in 53.33% of patients but produced good to excellent intubating conditions in 96.67% of patients. Rocuronium bromide 0.9 mg kg - 1

  7. Temperature Dependence of Mineral Solubility in Water. Part 2. Alkaline and Alkaline Earth Bromides

    Science.gov (United States)

    Krumgalz, B. S.

    2018-03-01

    Databases of alkaline and alkaline earth bromide solubilities in water at various temperatures were created using experimental data from publications over about the last two centuries. Statistical critical evaluation of the created databases was produced since there were enough independent data sources to justify such evaluation. The reliable experimental data were adequately described by polynomial expressions over various temperature ranges. Using the Pitzer approach for ionic activity and osmotic coefficients, the thermodynamic solubility products for the discussed bromide minerals have been calculated at various temperature intervals and also represented by polynomial expressions.

  8. Biodegradation of imidazolium ionic liquids by activated sludge microorganisms.

    Science.gov (United States)

    Liwarska-Bizukojc, Ewa; Maton, Cedric; Stevens, Christian V

    2015-11-01

    Biological properties of ionic liquids (ILs) have been usually tested with the help of standard biodegradation or ecotoxicity tests. So far, several articles on the identification of intermediate metabolites of microbiological decay of ILs have been published. Simultaneously, the number of novel ILs with unrecognized characteristics regarding biodegradability and effect on organisms and environment is still increasing. In this work, seven imidazolium ionic liquids of different chemical structure were studied. Three of them are 1-alkyl-3-methyl-imidazolium bromides, while the other four are tetra- or completely substituted imidazolium iodides. This study focused on the identification of intermediate metabolites of the aforementioned ionic liquids subjected to biodegradation in a laboratory activated sludge system. Both fully substituted ionic liquids and 1-ethyl-3-methyl-imidazolium bromide were barely biodegradable. In the case of two of them, no biotransformation products were detected. The elongation of the alkyl side chain made the IL more susceptible for microbiological decomposition. 1-Decyl-3-methyl-imidazolium bromide was biotransformed most easily. Its primary biodegradation up to 100 % could be achieved. Nevertheless, the cleavage of the imidazolium ring has not been observed.

  9. Purification of the labeled cyanogen bromide peptides of the α polypeptide from sodium and potassium ion-activated adenosinetriphosphatase modified with N-[3H]ethylmaleimide

    International Nuclear Information System (INIS)

    Le, D.T.

    1985-01-01

    Sodium and potassium ion-activated adenosinetriphosphatase, isolated from canine kidney, was reacted with N-[ 3 H]ethylmaleimide under three different conditions, defined by particular concentrations of ligands for the enzyme, such that after the same amount of time the remaining activity of then enzyme varied from 90% to 30%. The conformation of the enzyme also differed among the three conditions. In all cases, the α-polypeptide was purified and subjected to cyanogen bromide digestion. Two distinct, radioactive peptides were separated by gel filtration of the cyanogen bromide digest on a column of Sephadex LH-60 equilibrated with 95% ethanol: 88% formic acid:4:1. One of the radioactive peptides was shown to contain the sulfhydryl residue whose reaction with N-ethylmaleimide inactivates the enzyme. The other radioactive peptide contained a sulfhydryl residue that seems to react with N-ethylmaleimide only when the binding site for ATP is not occupied. Alkylation of this residue, however, does not result in inactivation of enzyme. Both peptides were purified further by high-pressure liquid chromatography, and their amino-terminal sequences were determined by the manual dansyl-Edman or solid-phase techniques. The peptide containing the sulfhydryl protected by ATP has, as its amino terminus, the lysine that reacts exclusively with fluorescein-5'-isothiocyanate

  10. Effects of soil type, moisture content, redox potential and methyl bromide fumigation on Kd values of radio-selenium in soil

    International Nuclear Information System (INIS)

    Ashworth, D.J.; Moore, J.; Shaw, G.

    2008-01-01

    Understanding the processes that determine the solid-liquid partitioning (K d value) of Se is of fundamental importance in assessing the risk associated with the disposal of radio-selenium-containing waste. Using a mini-column (rather than batch) approach, K d values for 75 Se were determined over time in relation to soil moisture content (field capacity or saturated), redox potential and methyl bromide fumigation (used to disrupt the soil microbial population) in three contrasting soil types: clay loam, organic and sandy loam. The K d values were generally in the range 50-500 L kg -1 , with mean soil K d increasing with increasing organic matter content. Saturation with water lowered the measured redox potentials in the soils. However, only in the sandy loam soil did redox potential become negative, and this led to an increase in 75 Se K d value in this soil. Comparison of the data with the Eh-pH stability diagram for Se suggested that such strong reduction may have been consistent with the formation of the insoluble Se species, selenide. These findings, coupled with the fact that methyl bromide fumigation had no discernible effect on 75 Se K d value in the sandy loam soil, suggest that geochemical, rather than microbial, processes controlled 75 Se partitioning. The inter-relations between soil moisture content, redox potential and Se speciation should be considered in the modelling and assessment of radioactive Se fate and transport in the environment

  11. Visible-Light-Initiated Na2-Eosin Y Catalyzed Highly Regio- and Stereoselective Difunctionalization of Alkynes with Alkyl Bromides.

    Science.gov (United States)

    Wang, Kuai; Meng, Ling-Guo; Wang, Lei

    2016-08-19

    A highly regioselective and stereoselective addition of alkyl bromides (amino-brominated aromatic β,β-dicyanoalkenes) to arylacetylenes by photoredox catalysis was developed. This difunctionalization of arylacetylenes was accomplished under ambient and metal-free conditions to produce alkenyl bromides in high efficiency with a wide range of group tolerance.

  12. Synthesis of electrophilic 11C-synthons: 11C-cyanogen bromide and some 11C-cyano reagents

    International Nuclear Information System (INIS)

    Westerberg, G.; Malmborg, P.; Langstroem, B.

    1990-01-01

    A fast, simple, and reliable method has been developed for the synthesis of carbon-11 labelled cyanogen bromide and several of its stabilized amine salts or cyanates. Preparation of cyanogen bromide is by bromination (bromine gas) of carbon-11 labelled hydrocyanic acid, followed by reaction with a tertiary amine or a phenol to yield the ammonium salts or cyanates

  13. A rapid method to estimate uranium using ionic liquid as extracting agent from basic aqueous media

    International Nuclear Information System (INIS)

    Prabhath Ravi, K.; Sathyapriya, R.S.; Rao, D.D.; Ghosh, S.K.

    2016-01-01

    Room temperature ionic liquids, as their name suggests are salts with a low melting point typically less than 100 °C and exist as liquid at room temperature. The common cationic parts of ionic liquids are imidazolium, pyridinium, pyrrolidinium, quaternary ammonium, or phosphonium ions, and common anionic parts are chloride, bromide, boron tetrafluorate, phosphorous hexafluorate, triflimide etc. The physical properties of ionic liquids can be tuned by choosing appropriate cations with differing alkyl chain lengths and anions. Application of ionic liquids in organic synthesis, liquid-liquid extractions, electrochemistry, catalysis, speciation studies, nuclear reprocessing is being studied extensively in recent times. In this paper a rapid method to estimate the uranium content in aqueous media by extraction with room temperature ionic liquid tricaprylammoniumthiosalicylate ((A- 336)(TS)) followed by liquid scintillation analysis is described. Re-extraction of uranium from ionic liquid phase to aqueous phase was also studied

  14. Ionothermal Synthesis of a Novel 3D Cobalt Coordination Polymer with a Uniquely Reported Framework: [BMI]2[Co2(BTC2(H2O2

    Directory of Open Access Journals (Sweden)

    Il-Ju Ko

    2017-01-01

    Full Text Available The framework of [RMI]2[Co2(BTC2(H2O2] (RMI = 1-alkyl-3-methylimidazolium, alkyl; ethyl (EMI; propyl (PMI; butyl (BMI, which has uniquely occurred in ionothermal reactions of metal salts and H3BTC (1,3,5-benzenetricarboxylic acid, an organic ligand, reappeared in this work. Ionothermal reaction of cobalt acetate and H3BTC with [BMI]Br ionic liquid as the reaction medium yielded the novel coordination polymer [BMI]2[Co2(BTC2(H2O2] (compound B2. Similar ionothermal reactions with different [EMI]Br and [PMI]Br as the reaction media have been previously reported to produce [EMI]2[Co3(BTC2(OAc2] (compound A1 and [PMI]2[Co2(BTC2(H2O2] (compound B1, respectively. In contrast with the trinuclear secondary building unit of A1, the framework structure of B1 and B2 consists of dinuclear secondary building units in common, but with subtle distinction posed by the different size of the incorporated cations. These structural differences amidst the frameworks showed interesting aspects, including guest and void volume, and were used to explain the chemical trend observed in the system. Moreover, the physicochemical properties of the newly synthesized compound have been briefly discussed.

  15. Mitochondrial genetic damage induced in yeast by a photoactivated furocoumarin in combination with ethidium bromide or ultraviolet light

    International Nuclear Information System (INIS)

    Juliani, M.H.; Hixon, S.; Moustacchi, E.

    1976-01-01

    Ethidium bromide (EB) and ultraviolet light (UV) in combination are known to produce a synergistic induction of 'petite' mutants in yeast. Two other agents were combined with EB, 3-Carbethoxypsoralene (3 CPs) activated by 365 nm light or γ rays. EB in combination with 3 CPs also resulted in an enhanced production of 'petite' mutants. After the photoaddition of 3 CPs in exponential phase cells, recovery of the 'petite' mutation during dark liquid holding was inhibited by the presence of EB producing an enhanced number of 'petite' mutants. The behavior of mitochondrial antibiotic resistance markers after individual and combined treatments with EB and 3 CPs indicates a random loss of markers after EB and a preferential loss of a certain region for the 3 CPs photoaddition. The combination of the two agents leads to an additivity of total drug marker losses rather than a synergistic loss. The combination of EB with γ rays produced no enhancement in 'petite' induction. A combination of UV and 3 CPs showed a synergistic interaction for 'petite' induction. These results indicate that the three agents, EB, UV and 3 CPs photoaddition may share a common repair step for mitochondrial lesions. (orig.) [de

  16. Distribution of bromine in mixed iodide-bromide organolead perovskites and its impact on photovoltaic performance

    NARCIS (Netherlands)

    Zhou, Yang; Wang, Feng; Fang, Hong-Hua; Loi, Maria Antonietta; Xie, Fang-Yan; Zhao, Ni; Wong, Ching-Ping

    2016-01-01

    Mixed iodide-bromide (I-Br) organolead perovskites are of great interest for both single junction and tandem solar cells since the optical bandgap of the materials can be tuned by varying the bromine to iodine ratio. Yet, it remains unclear how bromine incorporation modifies the properties of the

  17. Application of vacuum membrane distillation to lithium bromide absorption refrigeration system

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zanshe; Feng, Shiyu; Li, Yun [School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an 710049 (China); Gu, Zhaolin [School of Human Settlement and Civil Engineering, Xi' an Jiaotong University, Xi' an 710049 (China)

    2009-11-15

    Conventional generator in lithium bromide absorption refrigeration system is too bulky and heavy to be fitted into small scale device, and the temperature of the driving heater in the generator seems much higher than low grade energy such as regenerative energy or waste heat energy. In this paper, desorption of aqueous lithium bromide solution by vacuum membrane distillation process was presented. Hollow fiber membrane module made by polyvinylidene fluoride was used as desorption device of aqueous lithium bromide solution. Influencing factors of feed flux, feed temperature in lumen side and vacuum pressure in shell side were tested and analyzed with orthogonal test. The results showed that permeation flux of water vapor increased with the feed temperature increasing and the feed flux increasing in lumen side, and the permeation flux also went up along with absolute pressure drop in shell side. Feasibility and potential application analysis shows that the temperature of the driving heat was low and the volume and weight of the desorption device was light. In this study, vacuum membrane distillation to the lithium bromide absorption refrigeration system has proved to be an efficient and cheap desorption mode. (author)

  18. Once-daily glycopyrronium bromide, a long-acting muscarinic antagonist, for chronic obstructive pulmonary disease

    DEFF Research Database (Denmark)

    Ulrik, Charlotte Suppli

    2012-01-01

    Long-acting bronchodilators are central in the pharmacological management of patients with chronic obstructive pulmonary disease (COPD). The aim of this systematic review is to provide an overview of the studies evaluating the safety and clinical efficacy of inhaled glycopyrronium bromide, a novel...... long-acting muscarinic antagonist, in patients with COPD....

  19. Valence photoelectron spectra of alkali bromides calculated within the propagator theory

    DEFF Research Database (Denmark)

    Karpenko, Alexander; Iablonskyi, Denys; Aksela, Helena

    2013-01-01

    The valence ionization spectra covering the binding energy range 0-45 eV of alkali bromide XBr (X = Li, Na, K, Rb) vapors are studied within the framework of the propagator theory. Relativistic Algebraic Diagrammatic Construction calculations have been carried out in order to investigate photoion...... photoionization processes and to describe molecular electronic structure. Theoretical results are compared with available experimental data....

  20. Methyl bromide fumigation and delayed mortality: safe trade of live pests?

    Science.gov (United States)

    Phillips, C B; Iline, I I; Novoselov, M; McNeill, M R; Richards, N K; van Koten, C; Stephenson, B P

    Live organisms intercepted from treated commodities during phytosanitary inspections usually arouse suspicions of treatment failure, sub-standard treatment application, or post-treatment infestation. The additional possibility that some treatments could kill slowly, meaning commodities might be inspected before pests have succumbed, is seldom considered for treatments other than irradiation. We used a novel biochemical viability assay to measure delays between methyl bromide fumigation and mortality of dipteran eggs, and evaluated the correspondence between egg viability and egg morphological features. Our experimental conditions simulated shipping of rock melons from Australia to New Zealand by sea and air. No eggs survived fumigation, but they took 3-20 days to die, whereas phytosanitary inspections of rock melons occur within 2-7 days. Delays were not influenced by methyl bromide concentration, but were significantly lengthened by cooler storage temperatures. Methyl bromide's preservative effects delayed degradation of egg morphology, so the biochemical assay detected mortality long before morphological signs of egg death appeared. The results show that commodities subjected to effective methyl bromide treatments are at risk of being inspected before all pests have either died, or started to exhibit morphological signs of death. This could cause commodities to be unnecessarily rejected by quarantine authorities. Better methods than inspection for live pests are needed to assist authorities to gain assurance that treated commodities have been effectively disinfested. These could be developed by exploiting biochemical responses of pests and commodities to treatments.

  1. SYNTHESIS AND CATALYTIC PROPERTIES OF CROSS-LINKED HYDROPHOBICALLY ASSOCIATING POLY(ALKYLMETHYLDIALLYLAMMONIUM BROMIDES)

    NARCIS (Netherlands)

    WANG, GJ; ENGBERTS, JBFN

    1994-01-01

    Cross-linked, hydrophobically associating homo- and copolymers were synthesized by free-radical cyclo(co)polymerization of alkylmethyldiallylammonium bromide monomers with a small amount of N,N'-methylenebisacrylamide in aqueous solution using ammonium persulfate as the initiator. The cross-linked

  2. Unilateral mydriasis secondary to ipratropium bromide in a critically ill patient

    Directory of Open Access Journals (Sweden)

    Luciano Santana-Cabrera

    2012-01-01

    Full Text Available Unilateral dilated pupil in a critical patient under sedation is an important clinical sign that requires prompt evaluation. An exhaustive assessment must be performed, including neurological examination and imaging tests, and pharmacological causes must be ruled out. We describe a case of unilateral fixed dilated pupil secondary to the administration of a nebulized cholinergic antagonist, ipratropium bromide, in an unconscious patient.

  3. Microwave-Enhanced Cross-Coupling Reactions Involving Alkynyltrifluoroborates with Aryl Bromides

    Directory of Open Access Journals (Sweden)

    George W. Kabalka

    2013-01-01

    Full Text Available Palladium-catalyzed alkynylation has emerged as one of the most reliable methods for the synthesis of alkynes which are often used in natural product syntheses and material science. An efficient method for coupling alkynyltrifluoroborates with various aryl bromides in the presence of a palladium catalyst has been developed using microwave irradiation. The microwave reactions are rapid and efficient.

  4. Gold micro- and nano-particles for surface enhanced vibrational spectroscopy of pyridostigmine bromide

    DEFF Research Database (Denmark)

    Dolgov, Leonid; Fesenko, Olena; Kavelin, Vladyslav

    2017-01-01

    Triangular gold microprisms and spherical silica nanoparticles with attached gold nano-islands were examined as an active nanostructures for the surface enhanced Raman and infrared spectroscopy. These particles were probed for the detection of pyridostigmine bromide as a safe analog of military c...

  5. SYBR safeTM efficiently replaces ethidium bromide in Aspergillus fumigatus gene disruption.

    Science.gov (United States)

    Canela, H M S; Takami, L A; Ferreira, M E S

    2017-02-08

    Invasive aspergillosis is a disease responsible for high mortality rates, caused mainly by Aspergillus fumigatus. The available drugs are limited and this disease continues to occur at an unacceptable frequency. Gene disruption is essential in the search for new drug targets. An efficient protocol for A. fumigatus gene disruption was described but it requires ethidium bromide, a genotoxic agent, for DNA staining. Therefore, the present study tested SYBR safe TM , a non-genotoxic DNA stain, in A. fumigatus gene disruption protocol. The chosen gene was cipC, which has already been disrupted successfully in our laboratory. A deletion cassette was constructed in Saccharomyces cerevisiae and used in A. fumigatus transformation. There was no statistical difference between the tested DNA stains. The success rate of S. cerevisiae transformation was 63.3% for ethidium bromide and 70% for SYBR safe TM . For A. fumigatus gene disruption, the success rate for ethidium bromide was 100 and 97% for SYBR safe TM . In conclusion, SYBR safe TM efficiently replaced ethidium bromide, making this dye a safe and efficient alternative for DNA staining in A. fumigatus gene disruption.

  6. PHARMACOKINETICS OF ROCURONIUM BROMIDE IN PATIENTS WITH AND WITHOUT RENAL-FAILURE

    NARCIS (Netherlands)

    COOPER, RA; MIRAKHUR, RK; WIERDA, JMKH; MADDINENI, VR

    We studied the onset and duration of action and pharmacokinetics of rocuronium bromide during anaesthesia with nitrous oxide, fentanyl and isoflurane after a single bolus dose of rocuronium (0.6 mg kg(-1)) in nine patients with chronic renal failure requiring regular haemodialysis, and in nine

  7. Comparison of bromide and nitrate transport in the Bainsvlei soil of ...

    African Journals Online (AJOL)

    Bromide is commonly used to simulate the movement of nitrate fertilisers through the soil profile. However, there exists no comparative evaluation of the leaching properties of Br- and NO3-_N under local soil and rainfall conditions at Bloemfontein. The purpose of this work was to conduct a field experiment to evaluate the ...

  8. Iodine catalyzed and tertiary butyl ammonium bromide promoted p reparation of b enzoxazaphosphininyl phenylboronates

    Directory of Open Access Journals (Sweden)

    K. R. Kishore K. Reddy,

    2009-05-01

    Full Text Available Benzoxazaphosphininyl Phenylboronates were prepared by O-Phosphorylation of potassium salt ofphenylboronic acid with cyclic phosphoromonochloridates in the presence of stoichiometric amount of Iodineand catalytic amount of tertiary butyl ammonium bromide at 50-60 °C in dry toluene.

  9. Use of Br-82 and I-131 radionuclides in studies of goitrogenic effects of exogenous bromide

    Czech Academy of Sciences Publication Activity Database

    Pavelka, Stanislav

    2012-01-01

    Roč. 291, č. 2 (2012), s. 379-383 ISSN 0236-5731 R&D Projects: GA ČR(CZ) GA304/08/0256 Institutional research plan: CEZ:AV0Z50110509 Keywords : bromide * goitrogenic effect * iodine radionuclides * thyroid hormone Subject RIV: ED - Physiology Impact factor: 1.467, year: 2012

  10. 77 FR 29341 - Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications...

    Science.gov (United States)

    2012-05-17

    ...: The amount of fumigant gas used (both methyl bromide and alternatives), price per pound of the... practices organic producers are using for their commodity. Structures and Facilities (Flour Mills, Rice... methods. For the economic assessment applicants must provide the following: Price per pound of fumigant...

  11. Optical and structural characterization of KBr crystals doped cadmium bromide (CdBr2)

    International Nuclear Information System (INIS)

    Bensouici, A.; Plaza, J.L.; Dieguez, E.; Halimi, O.; Guerbous, L.; Sebais, M.

    2010-01-01

    In this paper we demonstrate the presence of CdBr 2 and cadmium aggregates in KBr matrix during Czochralski growth of KBr crystals. The chemical decomposition of CdBr 2 due to high temperature of crystallisation and reformation of cadmium bromide seems to be responsible for this effect.

  12. Optical and structural characterization of KBr crystals doped cadmium bromide (CdBr{sub 2})

    Energy Technology Data Exchange (ETDEWEB)

    Bensouici, A., E-mail: bensouicia@yahoo.f [Laboratory of Crystallography (Saint Lucia), Department of Physics, Mentouri-Constantine University, Constantine (Algeria); Plaza, J.L., E-mail: joseluis.plaza@uam.e [Crystal Growth Laboratory (CGL), Departamento de Fisica de Materiales, Universidad Autonoma de Madrid, Madrid (Spain); Dieguez, E. [Crystal Growth Laboratory (CGL), Departamento de Fisica de Materiales, Universidad Autonoma de Madrid, Madrid (Spain); Halimi, O. [Laboratory of Crystallography (Saint Lucia), Department of Physics, Mentouri-Constantine University, Constantine (Algeria); Guerbous, L. [Centre de recherche nucleaire d' Alger (CRNA), Alger 16000 (Algeria); Sebais, M. [Laboratory of Crystallography (Saint Lucia), Department of Physics, Mentouri-Constantine University, Constantine (Algeria)

    2010-04-15

    In this paper we demonstrate the presence of CdBr{sub 2} and cadmium aggregates in KBr matrix during Czochralski growth of KBr crystals. The chemical decomposition of CdBr{sub 2} due to high temperature of crystallisation and reformation of cadmium bromide seems to be responsible for this effect.

  13. CL 14: Solvation structure and dynamics of room temperature ionic liquids

    International Nuclear Information System (INIS)

    Musat, Raluca M.; Polyansky, Dmitriy; Crowell, Robert A.; Thomas, Marie; Wishart, James F.; Takahashi, Kenji; Katsumura, Yosuke

    2010-01-01

    Room temperature ionic liquids (RTILs) have emerged as a new class of solvents that, due to their unique properties (e.g., low volatility, large electrochemical window, high conductivity, etc.), have several potential applications. Among these are their possible use in nuclear fuel reprocessing, dye sensitized solar cells, and CO 2 sequestration. The properties of a given class of RTILs depend strongly on the choice of the counter anion. In this contribution we present new results using both static and time-resolved EXAFS (ca. 1 ns resolution) and time resolved optical absorption spectroscopy on a series of bromide containing imidazolium salts. The static results provide detailed information of the solvation shell of the bromide ion while the time-resolved data shed light on the nature and chemical behavior of the lowest lying charge transfer band, the physical motion of the bromine atom and its conversion to di-bromide. The photochemistry of the charge transfer (CT) band of the room temperature ionic liquid 1-hexyl-3-methylimidazolium bromide is investigated using ultrafast transient absorption spectroscopy (TA) in the near-IR and steady state UV absorption. Irradiation of the CT band at 266 nm results in the steady state production of di-bromide which absorbs strongly at 266 nm. It is shown that this photoproduct, which is apparently very stable, adversely affects ultrafast transient absorption measurements. Flowing and simultaneously translating the sample mitigates this effect and reveals new transient species and dynamics within the detection window of 850 nm to 1250 nm. (authors)

  14. Highly Selective Liquid-Phase Benzylation of Anisole with Solid-Acid Zeolite Catalysts

    DEFF Research Database (Denmark)

    Poreddy, Raju; Shunmugavel, Saravanamurugan; Riisager, Anders

    2015-01-01

    Zeolites were evaluated as solid acid catalysts for the liquid-phase benzylation of anisole with benzyl alcohol, benzyl bromide, and benzyl chloride at 80 °C. Among the examined zeolites, H-mordenite-10 (H-MOR-10) demonstrated particular high activity (>99 %) and excellent selectivity (>96...

  15. A novel explicit approach to model bromide and pesticide transport in connected soil structures

    Directory of Open Access Journals (Sweden)

    J. Klaus

    2011-07-01

    Full Text Available The present study tests whether an explicit treatment of worm burrows and tile drains as connected structures is feasible for simulating water flow, bromide and pesticide transport in structured heterogeneous soils at hillslope scale. The essence is to represent worm burrows as morphologically connected paths of low flow resistance in a hillslope model. A recent Monte Carlo study (Klaus and Zehe, 2010, Hydrological Processes, 24, p. 1595–1609 revealed that this approach allowed successful reproduction of tile drain event discharge recorded during an irrigation experiment at a tile drained field site. However, several "hillslope architectures" that were all consistent with the available extensive data base allowed a good reproduction of tile drain flow response. Our second objective was thus to find out whether this "equifinality" in spatial model setups may be reduced when including bromide tracer data in the model falsification process. We thus simulated transport of bromide for the 13 spatial model setups that performed best with respect to reproduce tile drain event discharge, without any further calibration. All model setups allowed a very good prediction of the temporal dynamics of cumulated bromide leaching into the tile drain, while only four of them matched the accumulated water balance and accumulated bromide loss into the tile drain. The number of behavioural model architectures could thus be reduced to four. One of those setups was used for simulating transport of Isoproturon, using different parameter combinations to characterise adsorption according to the Footprint data base. Simulations could, however, only reproduce the observed leaching behaviour, when we allowed for retardation coefficients that were very close to one.

  16. A novel explicit approach to model bromide and pesticide transport in connected soil structures

    Science.gov (United States)

    Klaus, J.; Zehe, E.

    2011-07-01

    The present study tests whether an explicit treatment of worm burrows and tile drains as connected structures is feasible for simulating water flow, bromide and pesticide transport in structured heterogeneous soils at hillslope scale. The essence is to represent worm burrows as morphologically connected paths of low flow resistance in a hillslope model. A recent Monte Carlo study (Klaus and Zehe, 2010, Hydrological Processes, 24, p. 1595-1609) revealed that this approach allowed successful reproduction of tile drain event discharge recorded during an irrigation experiment at a tile drained field site. However, several "hillslope architectures" that were all consistent with the available extensive data base allowed a good reproduction of tile drain flow response. Our second objective was thus to find out whether this "equifinality" in spatial model setups may be reduced when including bromide tracer data in the model falsification process. We thus simulated transport of bromide for the 13 spatial model setups that performed best with respect to reproduce tile drain event discharge, without any further calibration. All model setups allowed a very good prediction of the temporal dynamics of cumulated bromide leaching into the tile drain, while only four of them matched the accumulated water balance and accumulated bromide loss into the tile drain. The number of behavioural model architectures could thus be reduced to four. One of those setups was used for simulating transport of Isoproturon, using different parameter combinations to characterise adsorption according to the Footprint data base. Simulations could, however, only reproduce the observed leaching behaviour, when we allowed for retardation coefficients that were very close to one.

  17. Osmotic and activity coefficients in the binary solutions of 1-butyl-3-methylimidazolium chloride and bromide in methanol or ethanol at T = 298.15 K from isopiestic measurements

    International Nuclear Information System (INIS)

    Sardroodi, Jaber Jahanbin; Azamat, Jafar; Atabay, Maryam

    2011-01-01

    Highlights: → The osmotic coefficients of the solutions of 1-butyl-3-methylimidazolium chloride and bromide in ethanol and methanol have been measured. → Measured osmotic coefficients were correlated using NRTL and Pitzer models. → Vapor pressures were evaluated from the correlated osmotic coefficients. → Model parameters have been interpreted in terms of ion-ion and ion-solvent interactions. - Abstract: Osmotic coefficients of the binary solutions of two room-temperature ionic liquids (1-butyl-3-methylimidazolium chloride and bromide) in methanol and ethanol have been measured at T = 298.15 K by the isopiestic method. The experimental osmotic coefficient data have been correlated using a forth-order polynomial in terms of (molality) 0.5 , with both, ion interaction model of Pitzer and electrolyte non-random two liquid (e-NRTL) model of Chen. The values of vapor pressures of above-mentioned solutions have been calculated from the osmotic coefficients. The model parameters fitted to the experimental osmotic coefficients have been used for prediction of the mean ionic activity coefficients of those ionic liquids in methanol and ethanol.

  18. Ease of intubation: A randomized, double-blind study to compare two doses of rocuronium bromide for endotracheal intubation.

    Science.gov (United States)

    Shukla, Aparna; Misra, Shilpi

    2016-01-01

    Clinical need for a nondepolarizing agent with a rapid onset time and a brief duration of action has led to the development of rocuronium bromide. The aim of this study was to evaluate optimal dose of rocuronium bromide for intubation and to compare the onset time, duration of action, intubating conditions, and hemodynamic effects of two doses of rocuronium bromide. A prospective, randomized, double-blind study. All the patients were divided in a randomized, double-blind fashion into two groups of twenty patients each. Group I patients received rocuronium bromide 0.6 mg/kg intravenously and intubated at 60 s, Group II patients received rocuronium bromide 0.9 mg/kg and intubated at 60 s. The neuromuscular block was assessed using single twitch stimulation of 0.1 Hz at adductor pollicis muscle of hand at every 10 s. The results were compiled and analyzed statistically using Chi-square test for qualitative data and Student's t -test for quantitative data. Time of onset was significantly shorter ( P Rocuronium bromide 0.9 mg/kg is a safer alternative to rocuronium bromide 0.6 mg/kg for endotracheal intubation with shorter time of onset and better intubating conditions.

  19. Comparison of phenobarbital with bromide as a first-choice antiepileptic drug for treatment of epilepsy in dogs.

    Science.gov (United States)

    Boothe, Dawn Merton; Dewey, Curtis; Carpenter, David Mark

    2012-05-01

    To compare efficacy and safety of treatment with phenobarbital or bromide as the first-choice antiepileptic drug (AED) in dogs. Double-blinded, randomized, parallel, clinical trial. 46 AED-naïve dogs with naturally occurring epilepsy. Study inclusion was based on age, history, findings on physical and neurologic examinations, and clinicopathologic test results. For either phenobarbital treatment (21 dogs) or bromide treatment (25), a 7-day loading dose period was initiated along with a maintenance dose, which was adjusted on the basis of monthly monitoring. Efficacy and safety outcomes were compared between times (baseline and study end [generally 6 months]) and between drugs. Phenobarbital treatment resulted in eradication of seizures (17/20 [85%]) significantly more often than did bromide (12/23 [52%]); phenobarbital treatment also resulted in a greater percentage decrease in seizure duration (88 ± 34%), compared with bromide (49 ± 75%). Seizure activity worsened in 3 bromide-treated dogs only. In dogs with seizure eradication, mean ± SD serum phenobarbital concentration was 25 ± 6 μg/mL (phenobarbital dosage, 4.1 ± 1.1 mg/kg [1.9 ± 0.5 mg/lb], p.o., q 12 h) and mean serum bromide concentration was 1.8 ± 0.6 mg/mL (bromide dosage, 31 ± 11 mg/kg [14 ± 5 mg/lb], p.o., q 12 h). Ataxia, lethargy, and polydipsia were greater at 1 month for phenobarbital-treated dogs; vomiting was greater for bromide-treated dogs at 1 month and study end. Both phenobarbital and bromide were reasonable first-choice AEDs for dogs, but phenobarbital was more effective and better tolerated during the first 6 months of treatment.

  20. Characterization of surfactant liquid crystal phases suitable for molecular alignment and measurement of dipolar couplings

    International Nuclear Information System (INIS)

    Barrientos, Laura G.; Dolan, Caroline; Gronenborn, Angela M.

    2000-01-01

    Media employed for imparting partial alignment onto solute molecules have recently attracted considerable attention, since they permit the measurement of NMR parameters for solute biomolecules commonly associated with solid state NMR. Here we characterize a medium which is based on a quasi-ternary surfactant system comprising cetylpyridinium bromide/hexanol/sodium bromide. We demonstrate that dilute solutions of this system can exist in liquid crystalline phases which orient in the magnetic field and allow the measurement of residual dipolar couplings under a variety of conditions. The present system is extremely versatile and robust, tolerating different buffer conditions, temperature ranges and concentrations

  1. Comparative microvascular exchange kinetics of [{sup 77}Br]bromide and {sup 99m}Tc-DTPA in humans

    Energy Technology Data Exchange (ETDEWEB)

    Cousins, Claire [Department of Clinical Radiology, Addenbrooke' s Hospital, Cambridge (United Kingdom); Skehan, Stephen J.; Rolph, Susan M.; Flaxman, Mary E.; Ballinger, James R.; Bird, Nicholas J.; Barber, Robert W.; Peters, Michael A. [Department of Nuclear Medicine, Addenbrooke' s Hospital, Cambridge (United Kingdom)

    2002-05-01

    The plasma clearance curves of small hydrophilic solutes comprise three exponentials, consistent with a three-compartmental distribution model. A previous comparison between inulin and diethylene triamine penta-acetic acid (DTPA) suggested that these three compartments are in series, the first being plasma and the second and third representing compartments within the extravascular space. Moreover, whilst the total distribution volumes of these two indicators were similar, the volume of the second compartment was higher for DTPA. The purpose of the current study was to investigate whether a solute smaller than DTPA, namely bromide, fits the hypothesis that the second space volume is an inverse function of the size of the solute. Two groups of subjects were studied: group A comprised eight patients undergoing routine diagnostic arteriography and group B, eight patients referred for routine measurement of glomerular filtration rate plus two normal volunteers. {sup 99m}Tc-DTPA and sodium [{sup 77}Br]bromide were intravenously administered simultaneously. In group A, frequent arterial samples were obtained up to 40 min after injection, and antecubital venous samples 30 s after each arterial sample. In group B, frequent venous samples were obtained up to 280 min after injection. Volume measurements based on bromide were corrected for erythrocyte bromide accumulation. In both subject groups, the normalised venous concentration ratio of bromide to DTPA, corrected for red cell bromide uptake, was significantly less than unity in the earliest blood samples, being 0.56 (SD 0.08) at 1 min, consistent with faster diffusion of bromide from plasma to interstitial fluid. Furthermore, the extraction fraction of bromide from plasma to interstitial fluid in the forearm was about 0.6, higher than that of DTPA (about 0.5) in spite of red cell bromide accumulation which equilibrated with plasma bromide within 20 s and resulted in a red cell to plasma concentration ratio of 0.51 (0

  2. Evaluation of the influence of base and alkyl bromide on synthesis of pyrazinoic acid esters through factorial design

    International Nuclear Information System (INIS)

    Fernandes, Joao Paulo dos Santos; Felli, Veni Maria Andres

    2009-01-01

    Pyrazinoic acid esters have been synthesized as prodrugs of pyrazinoic acid. In the literature, its preparation is reported through the reaction of pyrazinoyl chloride with alcohols and the reaction with DCC/DMAP. In this work, it is reported a 22 factorial design to evaluate the preparation of these esters through the substitution of alkyl bromides with carboxylate anion. The controlled factors were alkyl chain length of bromides (ethyl and hexyl) and the used base (triethylamine and DBU). Results revealed that the used base used has significant effect on yield, and alkyl bromide used has neither significant influence, nor its interaction effect with base. (author)

  3. Atmospheric volatilization of methyl bromide, 1,3-dichloropropene, and propargyl bromide through two plastic films: transfer coefficient and temperature effect

    Science.gov (United States)

    Wang, D.; Yates, S. R.; Gan, J.; Knuteson, J. A.

    Atmospheric emission of methyl bromide (MeBr) and its potential alternative chemicals such as 1,3-dichloropropene (1,3-D) and propargyl bromide (PrBr) can contribute to air pollution and ozone depletion (for MeBr). One of the main sources of these chemicals is from agricultural soil fumigation. To understand the volatilization dynamics, emission of MeBr, 1,3-D, and PrBr through a polyethylene-based high-barrier film (HBF) and a virtually impermeable film (VIF) was measured using an air flow and sampling system that produced >90% mass balance. The experiment was conducted outdoors and was subjected to ambient daily temperature variations. The HBF film was found to be very permeable to 1,3-D and PrBr, but somewhat less permeable to MeBr. The VIF film was very impermeable to 1,3-D, PrBr, or MeBr. Measured volatilization flux, in general, exhibited strong diurnal variations which were controlled by film temperature. Unlike the HBF film, a time lag (˜12 h) was observed between high-temperatures and high-emission flux values for the VIF film. An impermeable film may be used as an effective means of controlling the atmospheric emission of MeBr and its alternative chemicals.

  4. Indirect complexometric determination of mercury(II) using potassium bromide as selective masking agent

    International Nuclear Information System (INIS)

    Sreekumar, N.V.; Nazareth, R.A.; Narayana, B.; Hegde, P.; Manjunatha, B.R.

    2002-01-01

    A complexometric method for the determination of mercury in presence of other metal ions based on the selective masking ability of potassium bromide towards mercury is described. Mercury(II) present in a given sample solution is first complexed with a known excess of EDTA and the surplus EDTA is titrated against zinc sulfate solution at pH 5-6 using xylenol orange as the indicator. A known excess of 10 % solution of potassium bromide is then added and the EDTA released from Hg-EDTA complex is titrated against standard zinc sulfate solution. Reproducible and accurate results are obtained for 8 mg to 250 mg of mercury(II) with a relative error ±0.28 % and standard deviations /leg 0.5 mg. The interference of various ions is studied. This method was applied to the determination of mercury(II) in its alloys. (author)

  5. Temporary arrest of fetal movement with pancuronium bromide to enable antenatal magnetic resonance imaging of holoprosencephaly.

    Science.gov (United States)

    Horvath, L; Seeds, J W

    1989-10-01

    The well-known ability of real-time ultrasound to detect congenital abnormalities is often limited by acoustic artifact or fetal position or both. Magnetic resonance imaging can provide superior soft tissue resolution but is vulnerable to maternal and fetal motion artifact. Described and illustrated here is a case of fetal holoprosencephaly that was not of diagnostic clarity on ultrasound. The fetus was paralyzed with an intramuscular injection of pancuronium bromide before a resonance imaging study. Successful fetal paralysis with pancuronium bromide has been reported prior to a variety of fetal interventions for the temporary arrest of fetal movement. The resonance study illustrated here was of significantly superior clarity and improved the accuracy of prognosis and management counseling. It is concluded that in selected cases where ultrasound is not of diagnostic clarity due to acoustic artifact, fetal paralysis and magnetic resonance imaging may be considered.

  6. Apparent molal volumes of symmetrical and asymmetrical isomers of tetrabutylammonium bromide in water at several temperatures

    International Nuclear Information System (INIS)

    Moreno, Nicolás; Malagón, Andrés; Buchner, Richard; Vargas, Edgar F.

    2014-01-01

    Highlights: • Apparent molal volumes of five isomers of Bu 4 NBr in water have been measured. • The structural effect of branched and linear chains is discussed. • The structural contributions to the ionic volume were calculated. -- Abstract: Apparent molal volumes of a series of differently substituted quaternary ammonium bromides, namely tetra-iso-butyl-, tetra-sec-butyl-, tetra-n-butyl-, di-n-butyl-di-sec-butyl- and di-n-butyl-di-iso-butylammonium bromide have been determined as a function of molal concentration at (298.15, 303.15 and 308.15) K. Partial molar volumes at infinite dilution and ionic molar volumes of these quaternary ammonium cations were determined. Structural volume contributions to the ionic molar volume were also calculated. The symmetric and asymmetric quaternary ammonium cations are “structure making” ions. The contribution of the branched butyl chains predominates over the linear butyl chains in the asymmetric cations

  7. Preparation and optical characteristics of layered perovskite-type lead-bromide-incorporated azobenzene chromophores

    Science.gov (United States)

    Sasai, Ryo; Shinomura, Hisashi

    2013-02-01

    Lead bromide-based layered perovskite powders with azobenzene derivatives were prepared by a homogeneous precipitation method. From the diffuse reflectance (DR) and photoluminescence (PL) spectra of the hybrid powder materials, the present hybrids exhibited sharp absorption and PL peaks originating from excitons produced in the PbBr42- layer. When the present hybrid powder was irradiated with UV light at 350 nm, the absorption band from the trans-azobenzene chromophore, observed around 350 nm, decreased, while the absorption band from the cis-azobenzene chromophore, observed around 450 nm, increased. These results indicate that azobenzene chromophores in the present hybrid materials exhibit reversible photoisomerization. Moreover, it was found that the PL intensity from the exciton also varied due to photoisomerization of the azobenzene chromophores in the present hybrid. Thus, for the first time we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation.

  8. Mechanism of HERG potassium channel inhibition by tetra-n-octylammonium bromide and benzethonium chloride

    International Nuclear Information System (INIS)

    Long, Yan; Lin, Zuoxian; Xia, Menghang; Zheng, Wei; Li, Zhiyuan

    2013-01-01

    Tetra-n-octylammonium bromide and benzethonium chloride are synthetic quaternary ammonium salts that are widely used in hospitals and industries for the disinfection and surface treatment and as the preservative agent. Recently, the activities of HERG channel inhibition by these compounds have been found to have potential risks to induce the long QT syndrome and cardiac arrhythmia, although the mechanism of action is still elusive. This study was conducted to investigate the mechanism of HERG channel inhibition by these compounds by using whole-cell patch clamp experiments in a CHO cell line stably expressing HERG channels. Tetra-n-octylammonium bromide and benzethonium chloride exhibited concentration-dependent inhibitions of HERG channel currents with IC 50 values of 4 nM and 17 nM, respectively, which were also voltage-dependent and use-dependent. Both compounds shifted the channel activation I–V curves in a hyperpolarized direction for 10–15 mV and accelerated channel activation and inactivation processes by 2-fold. In addition, tetra-n-octylammonium bromide shifted the inactivation I–V curve in a hyperpolarized direction for 24.4 mV and slowed the rate of channel deactivation by 2-fold, whereas benzethonium chloride did not. The results indicate that tetra-n-octylammonium bromide and benzethonium chloride are open-channel blockers that inhibit HERG channels in the voltage-dependent, use-dependent and state-dependent manners. - Highlights: ► Tetra-n-octylammonium and benzethonium are potent HERG channel inhibitors. ► Channel activation and inactivation processes are accelerated by the two compounds. ► Both compounds are the open-channel blockers to HERG channels. ► HERG channel inhibition by both compounds is use-, voltage- and state dependent. ► The in vivo risk of QT prolongation needs to be studied for the two compounds

  9. Bromidotetra?kis?(2-isopropyl-1H-imidazole-?N 3)copper(II) bromide

    OpenAIRE

    Godlewska, Sylwia; Socha, Joanna; Baranowska, Katarzyna; Do??ga, Anna

    2011-01-01

    The CuII atom in the title salt, [CuBr(C6H10N2)4]Br, is coordinated in a square-pyramidal geometry by four imidazole N atoms and one bromide anion that is located at the apex of the pyramid. The cations and the anions form a two-dimensional network parallel to (001) through N—H...Br hydrogen bonds.

  10. Bromide (Br) - Based Synthesis of Ag Nanocubes with High-Yield

    OpenAIRE

    Wu, Fan; Wang, Wenhui; Xu, Zhongfeng; Li, Fuli

    2015-01-01

    The geometry of metal nanoparticles greatly affects the properties of the localized surface plasmon resonance and surface-enhanced Raman scattering. The synthesis of metal nanoparticles with controllable geometry has thus attracted extensive attentions. In this work, we report a modified polyol synthesis approach of silver (Ag) nanocubes through tuning the concentration of bromide ions (Br? ions). We have systematically investigated the effect of Br? ions in the polyol process, and find that ...

  11. Chemical effects of radiative thermal neutron capture. Part 5.- Potassium bromide

    International Nuclear Information System (INIS)

    Maddock, A. G.; Val Cob, M. del

    1961-01-01

    By the use of the bromine atom exchanging reagent CHBr: CHBr, it has been shown that the specific activity of the atomic bromine in pile-irradiated potassium bromide is greater than that of the total bromine. This result suggests that the inactive radiolytic bromine atoms and the ejected radioactive atoms occupy different defect sites, the latter most likely finding interstitial positrons. (Author) 6 refs

  12. Mechanism of HERG potassium channel inhibition by tetra-n-octylammonium bromide and benzethonium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Long, Yan; Lin, Zuoxian [Key Laboratory of Regenerative Biology, Guangzhou Institute of Biomedicine and Health, Chinese Academy of Sciences, Guangzhou 510530 (China); Xia, Menghang; Zheng, Wei [National Center for Advancing Translational Sciences, National Institutes of Health, Bethesda, MD 20892 (United States); Li, Zhiyuan, E-mail: li_zhiyuan@gibh.ac.cn [Key Laboratory of Regenerative Biology, Guangzhou Institute of Biomedicine and Health, Chinese Academy of Sciences, Guangzhou 510530 (China)

    2013-03-01

    Tetra-n-octylammonium bromide and benzethonium chloride are synthetic quaternary ammonium salts that are widely used in hospitals and industries for the disinfection and surface treatment and as the preservative agent. Recently, the activities of HERG channel inhibition by these compounds have been found to have potential risks to induce the long QT syndrome and cardiac arrhythmia, although the mechanism of action is still elusive. This study was conducted to investigate the mechanism of HERG channel inhibition by these compounds by using whole-cell patch clamp experiments in a CHO cell line stably expressing HERG channels. Tetra-n-octylammonium bromide and benzethonium chloride exhibited concentration-dependent inhibitions of HERG channel currents with IC{sub 50} values of 4 nM and 17 nM, respectively, which were also voltage-dependent and use-dependent. Both compounds shifted the channel activation I–V curves in a hyperpolarized direction for 10–15 mV and accelerated channel activation and inactivation processes by 2-fold. In addition, tetra-n-octylammonium bromide shifted the inactivation I–V curve in a hyperpolarized direction for 24.4 mV and slowed the rate of channel deactivation by 2-fold, whereas benzethonium chloride did not. The results indicate that tetra-n-octylammonium bromide and benzethonium chloride are open-channel blockers that inhibit HERG channels in the voltage-dependent, use-dependent and state-dependent manners. - Highlights: ► Tetra-n-octylammonium and benzethonium are potent HERG channel inhibitors. ► Channel activation and inactivation processes are accelerated by the two compounds. ► Both compounds are the open-channel blockers to HERG channels. ► HERG channel inhibition by both compounds is use-, voltage- and state dependent. ► The in vivo risk of QT prolongation needs to be studied for the two compounds.

  13. Chemical effects of radiative thermal neutron capture. Part 5.- Potassium bromide

    Energy Technology Data Exchange (ETDEWEB)

    Maddock, A G; Val Cob, M del

    1961-07-01

    By the use of the bromine atom exchanging reagent CHBr: CHBr, it has been shown that the specific activity of the atomic bromine in pile-irradiated potassium bromide is greater than that of the total bromine. This result suggests that the inactive radiolytic bromine atoms and the ejected radioactive atoms occupy different defect sites, the latter most likely finding interstitial positrons. (Author) 6 refs.

  14. The Effect of Ozonation Process on Bromide-Containing Groundwaters in Bandung Area and Its Surroundings

    Directory of Open Access Journals (Sweden)

    Mindriany Syafila

    2012-11-01

    Full Text Available Disinfection process was applied as the last step of the water treatment to kill pathogenic bacteria in the water. However, according to several studies, the ozonation disinfection process could form undesired by-products. One of the by-products potentially affecting human life is bromate produced from bromide ionic-containing water. This study was carried out to examine the effect of raw water characteristics and pH on bromate formation. Also, the performance of bromate formation for a period of exposure time was analyzed. Raw waters taken from four different areas around Bandung were exposed to ozone introduced to a reactor with a flow rate of 2 L/min. The pH of the raw waters varied from 4, 7 to 10. The results show that there was no evidence of an initial bromide ion concentration, whereas a change in pH value gives a significantly different outcome. In acidic condition (pH of 4 the bromate formation tends to decrease, whereas when the pH value increases to a pH of 10, the bromate formation increases. Therefore, for drinking water with a neutral pH, when bromide ions are detected in the raw water, the drinking water may be toxic due to the presence of bromate.

  15. The discovery and development of aclidinium bromide for the treatment of chronic obstructive pulmonary disease.

    Science.gov (United States)

    Malerba, Mario; Radaeli, Alessandro; Santini, Giuseppe; Morjaria, Jaymin; Mores, Nadia; Mondino, Chiara; Macis, Giuseppe; Montuschi, Paolo

    2018-06-01

    Bronchodilators, including long-acting muscarinic receptor antagonists (LAMAs), are a mainstay of the pharmacological treatment of chronic obstructive pulmonary disease (COPD). LAMAs act as bronchodilators principally by antagonizing airway smooth muscle cells M 3 muscarinic receptors. Aclidinium bromide is a twice-daily LAMA which was developed to improve on the efficacy and/or safety of previous LAMAs. Area covered: Herein, the authors present the pharmacotherapeutic role of aclidinium in COPD and point out unmet need in this research area. The following aspects are covered: a) the discovery and medicinal chemistry of aclidinium bromide; b) an overview of the market; c) its mechanism of action; d) its pharmacokinetic/pharmacodynamic profile derived from pre-clinical studies; e) the clinical studies which led to its licensing; f) the evidence from meta-analyses; g) the aclidinium/formoterol fixed dose combination for COPD and h) priorities in this area of research. Expert opinion: Aclidinium bromide has the pharmacological properties, safety and efficacy profile and inhaler characteristics which makes it a valuable therapeutic option for pharmacological management of patients with COPD. Due to its rapid biotransformation into inactive metabolites, aclidinium is potentially one of the safest LAMAs. Further head-to-head randomized clinical trials are required to define efficacy and safety of aclidinium when compared to once-daily LAMAs. The clinical relevance of airway anti-remodeling effects of aclidinium has to be defined.

  16. Preparation and optical characteristics of layered perovskite-type lead-bromide-incorporated azobenzene chromophores

    International Nuclear Information System (INIS)

    Sasai, Ryo; Shinomura, Hisashi

    2013-01-01

    Lead bromide-based layered perovskite powders with azobenzene derivatives were prepared by a homogeneous precipitation method. From the diffuse reflectance (DR) and photoluminescence (PL) spectra of the hybrid powder materials, the present hybrids exhibited sharp absorption and PL peaks originating from excitons produced in the PbBr 4 2− layer. When the present hybrid powder was irradiated with UV light at 350 nm, the absorption band from the trans-azobenzene chromophore, observed around 350 nm, decreased, while the absorption band from the cis-azobenzene chromophore, observed around 450 nm, increased. These results indicate that azobenzene chromophores in the present hybrid materials exhibit reversible photoisomerization. Moreover, it was found that the PL intensity from the exciton also varied due to photoisomerization of the azobenzene chromophores in the present hybrid. Thus, for the first time we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation. - Graphical abstract: For the first time, we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation. Highlights: ► PbBr-based layered perovskite with azobenezene derivatives could be synthesized by a homogeneous precipitation method. ► Azobenzene derivatives incorporated the present hybrid that exhibited reversible photoisomerization under UV and/or visible light irradiation. ► PL property of the present hybrid could also be varied by photoisomerization.

  17. Toxic impact of bromide and iodide on drinking water disinfected with chlorine or chloramines.

    Science.gov (United States)

    Yang, Yang; Komaki, Yukako; Kimura, Susana Y; Hu, Hong-Ying; Wagner, Elizabeth D; Mariñas, Benito J; Plewa, Michael J

    2014-10-21

    Disinfectants inactivate pathogens in source water; however, they also react with organic matter and bromide/iodide to form disinfection byproducts (DBPs). Although only a few DBP classes have been systematically analyzed for toxicity, iodinated and brominated DBPs tend to be the most toxic. The objectives of this research were (1) to determine if monochloramine (NH2Cl) disinfection generated drinking water with less toxicity than water disinfected with free chlorine (HOCl) and (2) to determine the impact of added bromide and iodide in conjunction with HOCl or NH2Cl disinfection on mammalian cell cytotoxicity and genomic DNA damage induction. Water disinfected with chlorine was less cytotoxic but more genotoxic than water disinfected with chloramine. For both disinfectants, the addition of Br(-) and I(-) increased cytotoxicity and genotoxicity with a greater response observed with NH2Cl disinfection. Both cytotoxicity and genotoxicity were highly correlated with TOBr and TOI. However, toxicity was weakly and inversely correlated with TOCl. Thus, the forcing agents for cytotoxicity and genotoxicity were the generation of brominated and iodinated DBPs rather than the formation of chlorinated DBPs. Disinfection practices need careful consideration especially when using source waters containing elevated bromide and iodide.

  18. Room temperature synthesis of silver nanowires from tabular silver bromide crystals in the presence of gelatin

    Science.gov (United States)

    Liu, Suwen; Wehmschulte, Rudolf J.; Lian, Guoda; Burba, Christopher M.

    2006-03-01

    Long silver nanowires were synthesized at room temperature by a simple and fast process derived from the development of photographic films. A film consisting of an emulsion of tabular silver bromide grains in gelatin was treated with a photographic developer (4-(methylamino)phenol sulfate (metol), citric acid) in the presence of additional aqueous silver nitrate. The silver nanowires have lengths of more than 50 μm, some even more than 100 μm, and average diameters of about 80 nm. Approximately, 70% of the metallic silver formed in the reduction consists of silver nanowires. Selected area electron diffraction (SAED) results indicate that the silver nanowires grow along the [111] direction. It was found that the presence of gelatin, tabular silver bromide crystals and silver ions in solution are essential for the formation of the silver nanowires. The nanowires appear to originate from the edges of the silver bromide crystals. They were characterized by transmission electron microscopy (TEM), SAED, scanning electron microscopy (SEM), and powder X-ray diffraction (XRD).

  19. Room temperature synthesis of silver nanowires from tabular silver bromide crystals in the presence of gelatin

    International Nuclear Information System (INIS)

    Liu Suwen; Wehmschulte, Rudolf J.; Lian Guoda; Burba, Christopher M.

    2006-01-01

    Long silver nanowires were synthesized at room temperature by a simple and fast process derived from the development of photographic films. A film consisting of an emulsion of tabular silver bromide grains in gelatin was treated with a photographic developer (4-(methylamino)phenol sulfate (metol), citric acid) in the presence of additional aqueous silver nitrate. The silver nanowires have lengths of more than 50 μm, some even more than 100 μm, and average diameters of about 80 nm. Approximately, 70% of the metallic silver formed in the reduction consists of silver nanowires. Selected area electron diffraction (SAED) results indicate that the silver nanowires grow along the [111] direction. It was found that the presence of gelatin, tabular silver bromide crystals and silver ions in solution are essential for the formation of the silver nanowires. The nanowires appear to originate from the edges of the silver bromide crystals. They were characterized by transmission electron microscopy (TEM), SAED, scanning electron microscopy (SEM), and powder X-ray diffraction (XRD)

  20. Electrolytic coloration and spectral properties of hydroxyl-doped potassium bromide single crystals

    International Nuclear Information System (INIS)

    Qi, Lan; Song, Cuiying; Gu, Hongen

    2013-01-01

    Hydroxyl-doped potassium bromide single crystals are colored electrolytically at various temperatures and voltages by using a pointed cathode and a flat anode. The characteristic OH − spectral band is observed in absorption spectrum of uncolored single crystal. The characteristic O − , OH − , U, V 2 , O 2− −V a + , M L1 , F and M spectral bands are observed simultaneously in absorption spectra of colored single crystals. Current–time curve for electrolytic coloration of hydroxyl-doped potassium bromide single crystal and its relationship with electrolytic coloration processes are given. Production and conversion of color centers are explained. - Highlights: ► We expanded the traditional electrolysis method. ► Hydroxyl-doped potassium bromide crystals were colored electrolytically for the first time. ► Useful V, F and F-aggregate color centers were produced in colored crystals. ► V color centers were produced directly and F as well as F-aggregate color centers indirectly.

  1. Pitting Corrosion Behavior of 304 SS and 316 SS Alloys in Aqueous Chloride and Bromide Solutions

    Directory of Open Access Journals (Sweden)

    Ibtehal Kareem Shakir

    2018-01-01

    Full Text Available The importance of the present work falls on the pitting corrosion behavior investigation of 304 SS and 316 SS alloys in 3.5 wt% of aqueous solution bearing with chloride and bromide anion at different solutions temperature range starting from (20-50oC due to the pitting corrosion tremendous effect on the economic, safety and materials loss due to leakage. The impact of solution temperatures on the pitting corrosion resistance at 3.5wt% (NaCl and NaBr solutions for the 304 SS and 316 SS has been investigated utilizing the cyclic polarization techniques at the potential range -400 to1000 mV vs. SCE at 40 mV/sec scan rate followed by the surface characterization employing Scanning Electron Microscope. The results show that a significant decline in the pitting corrosion potential Ep values of both stainless steel alloys in chloride and bromide solution during temperature increase attributed to the pitting corrosion potential decreased arises from the modification of the passive film properties. The surface examination using optical microscope and scanning electron microscope prove the occurring of higher pitting density over 304 SS in chloride solution than that observed in bromide solution with a non-circular lacy cover pitfall out at the center and falls inside the pits hall in comparison to the isolated circular lacy cover pit formed on 316 SS in 3.5wt% NaBr solution at 50 oC.

  2. Once-daily glycopyrronium bromide (Seebri Breezhaler(®)) for the treatment of chronic obstructive pulmonary disease (COPD)

    DEFF Research Database (Denmark)

    Ulrik, Charlotte Suppli

    2015-01-01

    INTRODUCTION: Long-acting bronchodilators are the mainstay of pharmacological therapy for patients with chronic obstructive pulmonary disease (COPD). The choice of optimal bronchodilator therapy for COPD is increasingly difficult for clinicians as new treatments are marketed. AREAS COVERED: Inhaled...... glycopyrronium bromide (Seebri Breezhaler®) is a well-tolerated long-acting anti-muscarinic agent (LAMA) with a fast onset of action. In patients with moderate to severe COPD, glycopyrronium bromide has clinically important effects on level of FEV1, use of relief medication, day-time dyspnea scores, and probably...... also on health status. Furthermore, glycopyrronium bromide also has beneficial effects on dynamic hyperinflation and, probably by that, exercise tolerance. Glycopyrronium bromide has been shown to reduce the rate of exacerbations in patients with moderate to severe COPD, although as a secondary outcome...

  3. Estimating Potential Increased Bladder Cancer Risk Due to Increased Bromide Concentrations in Sources of Disinfected Drinking Waters - slides

    Science.gov (United States)

    Public water systems are increasingly facing higher bromide levels in their source waters from anthropogenic contamination through coal-fired powerplants, conventional oil and gas extraction, and hydraulic fracturing. Climate change is likely to exacerbate this in coming years. W...

  4. Estimating Potential Increased Bladder Cancer Risk Due to Increased Bromide Concentrations in Sources of Disinfected Drinking Waters

    Science.gov (United States)

    Public water systems are increasingly facing higher bromide levels in their source waters from anthropogenic contamination through coal-fired power plants, conventional oil and gas extraction, and hydraulic fracturing. Climate change is likely to exacerbate this in coming years. ...

  5. Comparative study on bromide and iodide ion-isotopic exchange reactions using strongly basic anion exchange resin Duolite A-113

    International Nuclear Information System (INIS)

    Lokhande, R.S.; Dole, M.H.; Singare, P.U.

    2006-01-01

    Kinetics of ion-isotopic exchange reaction was studied using industrial grade ion exchange resin Duolite A-113. The radioactive isotopes 131 I and 82 Br were used to trace the ion-isotopic exchange reaction. The experiments were performed in the temperature range of 26.0degC to 43.0degC and the concentration of external ionic solution varying from 0.005 M to 0.100 M. For bromide ion-isotopic exchange reaction, the calculated values of specific reaction rate, initial rate of bromide ion exchange, and amount of bromide ions exchanged were obtained higher than that for iodide ion-isotopic exchange reaction under identical experimental conditions. The observed variation in the results for two ion-isotopic exchange reactions was due to the difference in the ionic size of bromide and iodide ions. (author)

  6. GREEN CHEMISTRY APPLICATION FOR THE SYNTHESIS OF (1-N-4’-METHOXYBENZYL-1,10-PHENANTHROLINIUM BROMIDE

    Directory of Open Access Journals (Sweden)

    Maulidan Firdaus

    2010-06-01

    Full Text Available A simple, energy-efficient, and relatively quick synthetic procedure for the synthesis of (1-N-4'-methoxybenzyl-1,10-phenanthrolinium bromide, based on green chemistry principles has been carried out. The synthesis was started by solvent-free reduction of p-anisaldehyde with NaBH4 to give 4-methoxybenzyl alcohol in 98% yield to be followed by solvent-free treatment of the resulted alcohol with PBr3 to yield 4-methoxybenzyl bromide (86%. Furthermore, the obtained bromide was reacted with 1,10-phenanthroline in acetone at reflux for 12 h to give the phenanthrolinium salt target in 68% yield.   Keywords: green chemistry, p-anisaldehyde, (1-N-4'-methoxybenzyl-1,10-phenanthrolinium bromide

  7. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, No Stack, More than 8 Hours

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  8. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Horizontal Stacks, 8 Hours or Less

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  9. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, No Stack, 8 Hours or Less

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  10. Prostate cancer and toxicity from critical use exemptions of methyl bromide: Environmental protection helps protect against human health risks

    Directory of Open Access Journals (Sweden)

    Budnik Lygia T

    2012-01-01

    Full Text Available Abstract Background Although ozone-depleting methyl bromide was destined for phase-out by 2005, it is still widely applied as a consequence of various critical-use-exemptions and mandatory international regulations aiming to restrict the spread of pests and alien species (e.g. in globalized transport and storage. The withdrawal of methyl bromide because of its environmental risk could fortuitously help in the containment of its human toxicity. Methods We performed a systematic review of the literature, including in vitro toxicological and epidemiological studies of occupational and community exposure to the halogenated hydrocarbon pesticide methyl bromide. We focused on toxic (especially chronic or carcinogenic effects from the use of methyl bromide, on biomonitoring data and reference values. Eligible epidemiological studies were subjected to meta-analysis. Results Out of the 542 peer reviewed publications between 1990-2011, we found only 91 referring to toxicity of methyl bromide and 29 using the term "carcinogenic", "neoplastic" or "mutagenic". Several studies provide new additional data pertaining to the mechanistic aspects of methyl bromide toxicity. Few studies have performed a detailed exposure assessment including biomonitoring. Three evaluated epidemiological studies assessed a possible association between cancer and methyl bromide. Overall, exposure to methyl bromide is associated with an increased risk of prostate cancer OR, 1.21; 95% CI (0,98-1.49, P = 0.076. Two epidemiological studies have analyzed environmental, non-occupational exposure to methyl bromide providing evidence for its health risk to the general public. None of the epidemiological studies addressed its use as a fumigant in freight containers, although recent field and case reports do refer to its toxic effects associated with its use in shipping and storage. Conclusions Both the epidemiological evidence and toxicological data suggest a possible link between methyl

  11. Hydrogen Bonding in Ion-pair Molecules in Vapors over ionic liquids, studied by Raman Spectroscopy and ab initio Calculations

    DEFF Research Database (Denmark)

    Berg, Rolf W.

    gaseous free state models. Some extreme examples are to be discussed: (1) The 1,1,3,3-tetramethyl-guanidinium chloride “molecule” [TMG-H-Cl] found [ref 1] to exist in gaseous state over its corresponding liquid in evacuated ampouls heated at ~225°C (Fig. 1); (2) the analogous bromide “molecule” [TMG...

  12. Surface tension and 0.1 MPa density data for 1-Cn-3-methylimidazolium iodides with n=3, 4, and 6, validated using a parachor and group contribution model

    Czech Academy of Sciences Publication Activity Database

    Součková, Monika; Klomfar, Jaroslav; Pátek, Jaroslav

    2015-01-01

    Roč. 83, April (2015), s. 52-60 ISSN 0021-9614 R&D Projects: GA ČR GA13-00145S; GA ČR GA101/09/0010 Institutional support: RVO:61388998 Keywords : density * surface tension * 1-alkyl-3-methylimidazolium iodide * group contribution method * parachor Subject RIV: BJ - Thermodynamics Impact factor: 2.196, year: 2015

  13. Micellar and analytical implications of a new potentiometric PVC sensor based on neutral ion-pair complexes of dodecylmethylimidazolium bromide-sodium dodecylsulfate.

    Science.gov (United States)

    Sanan, Reshu; Mahajan, Rakesh Kumar

    2013-03-15

    With an aim to characterize the micellar aggregates of imidazolium based ionic liquids, a new potentiometric PVC sensor based on neutral ion-pair complexes of dodecylmethylimidazolium bromide-sodium dodecylsulfate (C12MeIm(+)DS(-)) has been developed. The electrode exhibited a linear response for the concentration range of 7.9×10(-5)-9.8×10(-3) M with a super-Nernstian slope of 92.94 mV/decade, a response time of 5 s and critical micellar concentration (cmc) of 10.09 mM for C12MeImBr. The performance of the electrode in investigating the cmc of C12MeImBr in the presence of two drugs [promazine hydrochloride (PMZ) and promethazine hydrochloride (PMT)] and three triblock copolymers (P123, L64 and F68) has been found to be satisfactory on comparison with conductivity measurements. Various micellar parameters have been evaluated for the binary mixtures of C12MeImBr with drugs and triblock copolymers using Clint's, Rubingh's, and Motomura's approach. Thus the electrode offers a simple, straightforward and relatively fast technique for the characterization of micellar aggregates of C12MeImBr, complementing existing conventional techniques. Further, the analytical importance of proposed C12MeIm(+)-ISE as end point indicator in potentiometric titrations and for direct determination of cationic surfactants [cetylpyridinium chloride (CPC), tetradecyltrimethylammonium bromide (TTAB), benzalkonium chloride (BC)] in some commercial products was judged by comparing statistically with classical two-phase titration methods. Copyright © 2013 Elsevier Inc. All rights reserved.

  14. Examining the interrelationship between DOC, bromide and chlorine dose on DBP formation in drinking water--a case study.

    Science.gov (United States)

    Bond, Tom; Huang, Jin; Graham, Nigel J D; Templeton, Michael R

    2014-02-01

    During drinking water treatment aqueous chlorine and bromine compete to react with natural organic matter (NOM). Among the products of these reactions are potentially harmful halogenated disinfection by-products, notably four trihalomethanes (THM4) and nine haloacetic acids (HAAs). Previous research has concentrated on the role of bromide in chlorination reactions under conditions of a given NOM type and/or concentration. In this study different concentrations of dissolved organic carbon (DOC) from U.K. lowland water were reacted with varying amounts of bromide and chlorine in order to examine the interrelationship between the three reactants in the formation of THM4, dihaloacetic acids (DHAAs) and trihaloacetic acids (THAAs). Results showed that, in general, molar yields of THM4 increased with DOC, bromide and chlorine concentrations, although yields did fluctuate versus chlorine dose. In contrast both DHAA and THAA yields were mainly independent of changes in bromide and chlorine dose at low DOC (1 mg·L(-1)), but increased with chlorine dose at higher DOC concentrations (4 mg·L(-1)). Bromine substitution factors reached maxima of 0.80, 0.67 and 0.65 for the THM4, DHAAs and THAAs, respectively, at the highest bromide/chlorine ratio studied. These results suggest that THM4 formation kinetics depend on both oxidation and halogenation steps, whereas for DHAAs and THAAs oxidation steps are more important. Furthermore, they indicate that high bromide waters may prove more problematic for water utilities with respect to THM4 formation than for THAAs or DHAAs. While mass concentrations of all three groups increased in response to increased bromide incorporation, only the THMs also showed an increase in molar yield. Overall, the formation behaviour of DHAA and THAA was more similar than that of THM4 and THAA. © 2013.

  15. Removal of bromide from aqueous solutions using the UV/ZnO process based on the multivariate analysis model

    Directory of Open Access Journals (Sweden)

    Kolsoom Mohammad Moradi

    2017-02-01

    Full Text Available Background: Bromide is found naturally in groundwater and surface water. The rapid growth of industrial activities, drainage of surface runoff, and use of methyl bromide in pesticides has increased bromide discharge to the environment. Disinfection of water-containing bromide causes the creation of additional products of organo-halogenated that are considered cancer-causing agents. In this study, the effect and optimization of factors in removal of this ion was evaluated by using the nano-photocatalytic UV/ZnO process. Methods: This analytical study was conducted in a batch system by the phenol-red method. The test design was performed through the analysis model of multi-factor variance with 99 subjects, while the main, interactive, and reciprocal effects of variables, such as reaction time, catalyst concentration, bromide concentration, and pH at different levels of each factor, were analysed by using SPSS version 16. Results: The main, interactive, and reciprocal effects of factors were significant in three different levels with P < 0.001, and the optimal level of the factors reaction time, catalyst concentration, bromide concentration, and pH were 120 minutes, 0.5, 0.1, and 7 mg/L, respectively, by using the Schaffer test. The highest removal efficiency of 95% was obtained at least 91.56 and a maximum of 94.76% was obtained under optimal conditions of all factors. Conclusion: The results show that by optimization of factors, this process can be effectively used to remove bromide from aquatic environments.

  16. LIQUID-LIQUID EXTRACTION COLUMNS

    Science.gov (United States)

    Thornton, J.D.

    1957-12-31

    This patent relates to liquid-liquid extraction columns having a means for pulsing the liquid in the column to give it an oscillatory up and down movement, and consists of a packed column, an inlet pipe for the dispersed liquid phase and an outlet pipe for the continuous liquid phase located in the direct communication with the liquid in the lower part of said column, an inlet pipe for the continuous liquid phase and an outlet pipe for the dispersed liquid phase located in direct communication with the liquid in the upper part of said column, a tube having one end communicating with liquid in the lower part of said column and having its upper end located above the level of said outlet pipe for the dispersed phase, and a piston and cylinder connected to the upper end of said tube for applying a pulsating pneumatic pressure to the surface of the liquid in said tube so that said surface rises and falls in said tube.

  17. Evaluation of bromide mass discharge in a sandy aquifer at Vandenberg AFB, CA

    Science.gov (United States)

    Mackay, D. M.; Rasa, E.; Einarson, M.; Kaiser, P.; Chakraborty, I.; Scow, K. M.

    2009-12-01

    Side-by-side experiments were conducted by UC Davis research team at a former fuel station at Vandenberg Air Force Base (AFB) to evaluate the rate of transformation of methyl tert-butyl ether (MTBE) to tert-butyl alcohol (TBA) impacted by ethanol and to investigate evidence of TBA degradation under sulfate reducing conditions. On one side we injected groundwater amended with ethanol and MTBE. In the other lane we injected groundwater amended with TBA. On both sides, injected ground water was spiked with bromide tracer to provide estimates of groundwater flow direction variations, flow velocity, dispersion, and mobile mass loss resulting from diffusive sequestration into aquitards. 162 monitoring wells were aligned into seven transects located downgradient of the injection wells. The mass discharge approach was used to evaluate the natural attenuation of the injected constituents. In this talk we will focus on calculations of mass discharge of the bromide tracer at each of the seven monitoring well transects. The amount of bromide mass discharged through each transect was calculated for any sampling time using field measurements of break through curves. Cumulative mass discharges were estimated and, by iteration based on mass balance, the flow properties of the aquifer were estimated. The calibration process resulted in subtle but quantitatively important changes in our assumptions regarding key physical properties of the aquifer (thickness, porosity) which could be only approximately estimated by standard methods (coring, CPT, etc.). On the basis of this calibration, a more robust approach was devised for evaluating the source and fate of TBA in the aquifer.

  18. Overcoming beta-agonist tolerance: high dose salbutamol and ipratropium bromide. Two randomised controlled trials

    Directory of Open Access Journals (Sweden)

    Haney Sarah

    2007-03-01

    Full Text Available Abstract Background Asthmatics treated with long-acting beta-agonists have a reduced bronchodilator response to moderate doses of inhaled short acting beta-agonists during acute bronchoconstriction. It is not known if the response to higher doses of nebulised beta-agonists or other bronchodilators is impaired. We assessed the effect of long-acting beta-agonist treatment on the response to 5 mg nebulised salbutamol and to ipratropium bromide. Methods Two double-blind, placebo-controlled, crossover studies of inhaled formoterol 12 μg twice daily in patients with asthma. High-dose salbutamol: 36 hours after the last dose of 1 week of formoterol or placebo treatment, 11 subjects inhaled methacholine to produce a 20% fall in FEV1. Salbutamol 5 mg was then administered via nebuliser and the FEV1 was monitored for 20 minutes. Ipratropium: 36 hours after the last dose of 1 week of formoterol or placebo treatment, 11 subjects inhaled 4.5% saline to produce a 20% fall in FEV1. Salbutamol 200 μg or ipratropium bromide 40 μg was then inhaled and the FEV1 was monitored for 30 minutes. Four study arms compared the response to each bronchodilator after formoterol and placebo. Analyses compared the area under the bronchodilator response curves, adjusting for changes in pre-challenge FEV1, dose of provocational agent and FEV1 fall during the challenge procedure. Results The response to nebulised salbutamol was 15% lower after formoterol therapy compared to placebo (95% confidence 5 to 25%, p = 0.008. The response to ipratropium was unchanged. Conclusion Long-acting beta-agonist treatment induces tolerance to the bronchodilator effect of beta-agonists, which is not overcome by higher dose nebulised salbutamol. However, the bronchodilator response to ipratropium bromide is unaffected.

  19. Efficient SN2 fluorination of primary and secondary alkyl bromides by copper(I) fluoride complexes

    KAUST Repository

    Liu, Yanpin; Chen, Chaohuang; Li, Huaifeng; Huang, Kuo-Wei; Tan, Jianwei; Weng, Zhiqiang

    2013-01-01

    Copper(I) fluoride complexes ligated by phenanthroline derivatives have been synthesized and structurally characterized by X-ray crystallography. These complexes adopt as either ionic or neutral forms in the solid state, depending on the steric bulkiness of the substituent groups on the phenanthroline ligands. These complexes react with primary and secondary alkyl bromides to produce the corresponding alkyl fluorides in modest to good yields. This new method is compatible with a variety of important functional groups such as ether, thioether, amide, nitrile, methoxyl, hydroxyl, ketone, ester, and heterocycle moieties. © 2013 American Chemical Society.

  20. Effect of Urea on the Thermodynamics of Hexadecyltrimethylammonium Bromide Micelle Formation in Aqueous Solutions

    Science.gov (United States)

    Velikov, A. A.

    2018-02-01

    The effect of urea on the thermodynamics of hexadecyltrimethylammonium bromide (CTAB) micelle formation in aqueous urea solutions was studied by isothermal titration microcalorimetry. The thermodynamic functions of Δ H, Δ G, and Δ S of CTAB micelle formation were calculated. The critical micelle concentrations (CMC) were determined. The addition of urea to the solution decreased the micelle formation entropy. This was attributed to the "lowering" of the structural temperature of the solution, which led to an increased number of hydrogen bonds and structure formation of water.

  1. Aclidinium bromid forbedrer lungefunktionen og reducerer dyspnø hos patienter med KOL

    DEFF Research Database (Denmark)

    Ulrik, Charlotte Suppli

    2014-01-01

    Long-acting bronchodilators are central for treatment of COPD. This short review provides an overview of studies evaluating the efficacy of aclidinium bromide, a long-acting anticholinergic bronchodilator, for the treatment of COPD. Twice-daily dosing of aclidinium leads to clinically important...... improvements in forced expiratory volume in 1 second, health status, use of rescue medication, day-time dyspnoea and exercise tolerance. The available studies also suggest an effect on night-time dyspnoea and exacerbation rate in patients with COPD. Aclidinium seems to have potential for a significant role...

  2. Phase diagram of tetradecyltrimethylammonium bromide (TTAB) + water + octanol system with application of mechanical deformation

    Science.gov (United States)

    Yavuz, Aykut Evren; Masalci, Özgür; Kazanci, Nadide

    2014-11-01

    Morphological properties of tetradecyltrimethylammonium bromide (TTAB) + water + octanol system in different concentrations have been studied. In the process, isotropic phase (L1) and nematic calamitic (NC), nematic discotic (ND), hexagonal E and lamellar D anizotropic mesophases have been determined by polarizing microscopy method and partial ternary phase diagram of the system set up. Textural properties of the anisotropic mesophases of the system have been discussed and their birefringence values measured. Mechanical deformation has been applied to the mesophases. The textural properties and the birefringence values have been observed to be changed by the deformation, after and before which changes have been compared.

  3. Radiation Induced Formation of Acrylated Palm Oil Nanoparticles using Cetyltrimethylammonium Bromide Microemulsion System

    International Nuclear Information System (INIS)

    Rida Tajau; Rida Tajau; Wan Mohd Zin Wan Yunus

    2011-01-01

    In this study, we report the preparation of Acrylated Palm Oil (APO) nanoparticles using aqueous Cetyltrimethylammonium bromide (CTAB) microemulsion system. This microemulsion system which contains the dispersed APO nano droplets was subjected to the gamma irradiation to induce the formation of the crosslinked APO nanoparticle. After irradiation at higher doses, the size of APO nanoparticles was transformed from a submicron-sized to a nano-sized of the particles. Size decreasing might be due to the intermolecular and the intramolecular crosslinking reactions of the APO nanoparticles during the irradiation process. (author)

  4. Emission characteristics of plasma based on xenon-rubidium bromide mixture

    Science.gov (United States)

    Heneral, A. A.; Avtaeva, S. V.

    2017-10-01

    Luminescence spectra of a longitudinal pulse-periodic discharge in xenon mixture with rubidium bromide vapors (Xe-RbBr) are studied experimentally at low pressures. The conditions leading to the appearance of intense bands of ultraviolet radiation of exciplex XeBr* molecules in the spectral interval between 200 and 400 nm are found. The highest yield of UV radiation of XeBr* molecules is achieved when the temperature of discharge-tube walls is equal to 750°C. A maximum power of UV radiation from the entire plasma volume as high as 4.8 W is obtained.

  5. Copper bromide vapour laser with an output pulse duration of up to 320 ns

    International Nuclear Information System (INIS)

    Gubarev, F A; Fedorov, K V; Evtushenko, G S; Fedorov, V F; Shiyanov, D V

    2016-01-01

    We report the development of a copper bromide vapour laser with an output pulse duration of up to 320 ns. To lengthen the pulse, the discharge current was limited using a compound switch comprising a pulsed hydrogen thyratron and a tacitron. This technique permits limiting the excitation of the working levels at the initial stage of the discharge development to lengthen the inversion lifetime. The longest duration of a laser pulse was reached in tubes 25 and 50 mm in diameter for a pulse repetition rate of 2 – 4 kHz. (lasers and laser beams)

  6. Efficient SN2 fluorination of primary and secondary alkyl bromides by copper(I) fluoride complexes

    KAUST Repository

    Liu, Yanpin

    2013-11-11

    Copper(I) fluoride complexes ligated by phenanthroline derivatives have been synthesized and structurally characterized by X-ray crystallography. These complexes adopt as either ionic or neutral forms in the solid state, depending on the steric bulkiness of the substituent groups on the phenanthroline ligands. These complexes react with primary and secondary alkyl bromides to produce the corresponding alkyl fluorides in modest to good yields. This new method is compatible with a variety of important functional groups such as ether, thioether, amide, nitrile, methoxyl, hydroxyl, ketone, ester, and heterocycle moieties. © 2013 American Chemical Society.

  7. Liquid Ventilation

    Directory of Open Access Journals (Sweden)

    Qutaiba A. Tawfic

    2011-01-01

    Full Text Available Mammals have lungs to breathe air and they have no gills to breath liquids. When the surface tension at the air-liquid interface of the lung increases, as in acute lung injury, scientists started to think about filling the lung with fluid instead of air to reduce the surface tension and facilitate ventilation. Liquid ventilation (LV is a technique of mechanical ventilation in which the lungs are insufflated with an oxygenated perfluorochemical liquid rather than an oxygen-containing gas mixture. The use of perfluorochemicals, rather than nitrogen, as the inert carrier of oxygen and carbon dioxide offers a number of theoretical advantages for the treatment of acute lung injury. In addition, there are non-respiratory applications with expanding potential including pulmonary drug delivery and radiographic imaging. The potential for multiple clinical applications for liquid-assisted ventilation will be clarified and optimized in future. Keywords: Liquid ventilation; perfluorochemicals; perfluorocarbon; respiratory distress; surfactant.

  8. Subsidizing Liquidity

    DEFF Research Database (Denmark)

    Malinova, Katya; Park, Andreas

    2015-01-01

    the breakdown of trading fees between liquidity demanders and suppliers matters. Posted quotes adjust after the change in fee composition, but the transaction costs for liquidity demanders remain unaffected once fees are taken into account. However, as posted bid-ask spreads decline, traders (particularly......Facing increased competition over the last decade, many stock exchanges changed their trading fees to maker-taker pricing, an incentive scheme that rewards liquidity suppliers and charges liquidity demanders. Using a change in trading fees on the Toronto Stock Exchange, we study whether and why...... retail) use aggressive orders more frequently, and adverse selection costs decrease....

  9. Bromide Sources and Loads in Swiss Surface Waters and Their Relevance for Bromate Formation during Wastewater Ozonation.

    Science.gov (United States)

    Soltermann, Fabian; Abegglen, Christian; Götz, Christian; von Gunten, Urs

    2016-09-20

    Bromide measurements and mass balances in the catchments of major Swiss rivers revealed that chemical industry and municipal waste incinerators are the most important bromide sources and account for ∼50% and ∼20%, respectively, of the ∼2000 tons of bromide discharged in the Rhine river in 2014 in Switzerland. About 100 wastewater treatment plants (WWTPs) will upgrade their treatment for micropollutant abatement in the future to comply with Swiss regulations. An upgrade with ozonation may lead to unintended bromate formation in bromide-containing wastewaters. Measured bromide concentrations were industry). Wastewater ozonation formed little bromate at specific ozone doses of ≤0.4 mg O3/mg DOC, while the bromate yields were almost linearly correlated to the specific ozone dose for higher ozone doses. Molar bromate yields for typical specific ozone doses in wastewater treatment (0.4-0.6 mg O3/mg DOC) are ≤3%. In a modeled extreme scenario (in which all upgraded WWTPs release 10 μg L(-1) of bromate), bromate concentrations increased by major Swiss rivers and by several micrograms per liter in receiving water bodies with a high fraction of municipal wastewater.

  10. Impact of Wildfire Emissions on Chloride and Bromide Depletion in Marine Aerosol Particles.

    Science.gov (United States)

    Braun, Rachel A; Dadashazar, Hossein; MacDonald, Alexander B; Aldhaif, Abdulamonam M; Maudlin, Lindsay C; Crosbie, Ewan; Aghdam, Mojtaba Azadi; Hossein Mardi, Ali; Sorooshian, Armin

    2017-08-15

    This work examines particulate chloride (Cl - ) and bromide (Br - ) depletion in marine aerosol particles influenced by wildfires at a coastal California site in the summers of 2013 and 2016. Chloride exhibited a dominant coarse mode due to sea salt influence, with substantially diminished concentrations during fire periods as compared to nonfire periods. Bromide exhibited a peak in the submicrometer range during fire and nonfire periods, with an additional supermicrometer peak in the latter periods. Chloride and Br - depletions were enhanced during fire periods as compared to nonfire periods. The highest observed %Cl - depletion occurred in the submicrometer range, with maximum values of 98.9% (0.32-0.56 μm) and 85.6% (0.56-1 μm) during fire and nonfire periods, respectively. The highest %Br - depletion occurred in the supermicrometer range during fire and nonfire periods with peak depletion between 1.8-3.2 μm (78.8% and 58.6%, respectively). When accounting for the neutralization of sulfate by ammonium, organic acid particles showed the greatest influence on Cl - depletion in the submicrometer range. These results have implications for aerosol hygroscopicity and radiative forcing in areas with wildfire influence owing to depletion effects on composition.

  11. Study of the Reaction 2-(p-Nitrophenylethyl Bromide + OH− in Dimeric Micellar Solutions

    Directory of Open Access Journals (Sweden)

    María Luisa Moyá

    2011-11-01

    Full Text Available The dehydrobromination reaction 2-(p-nitrophenylethyl bromide + OH− was investigated in several alkanediyl-a-w-bis(dodecyldimethylammonium bromide, 12-s-12,2Br− (with s = 2, 3, 4, 5, 6, 8, 10, 12 micellar solutions, in the presence of NaOH 5 × 10−3 M. The kinetic data were quantitatively rationalized within the whole surfactant concentration range by using an equation based on the pseudophase ion-exchange model and taking the variations in the micellar ionization degree caused by the morphological transitions into account. The agreement between the theoretical and the experimental data was good in all the dimeric micellar media studied, except for the 12-2-12,2Br− micellar solutions. In this case, the strong tendency to micellar growth shown by the 12-2-12,2Br− micelles could be responsible for the lack of accordance. Results showed that the dimeric micelles accelerate the reaction more than two orders of magnitude as compared to water.

  12. Sociology in Global Environmental Governance? Neoliberalism, Protectionism and the Methyl Bromide Controversy in the Montreal Protocol

    Directory of Open Access Journals (Sweden)

    Brian J. Gareau

    2017-10-01

    Full Text Available Sociological studies of global agriculture need to pay close attention to the protectionist aspects of neoliberalism at the global scale of environmental governance. With agri-food studies in the social sciences broadening interrogations of the impact of neoliberalism on agri-food systems and their alternatives, investigating global environmental governance (GEG will help reveal its impacts on the global environment, global science/knowledge, and the potential emergence of ecologically sensible alternatives. It is argued here that as agri-food studies of neoliberalism sharpen the focus on these dimensions the widespread consequences of protectionism of US agri-industry in GEG will become better understood, and the solutions more readily identifiable. This paper illustrates how the delayed phase out of the toxic substance methyl bromide in the Montreal Protocol exemplifies the degree to which the US agri-industry may be protected at the global scale of environmental governance, thus prolonging the transition to ozone-friendly alternatives. Additionally, it is clear that protectionism has had a significant impact on the dissemination and interpretation of science/knowledge of methyl bromide and its alternatives. Revealing the role that protectionism plays more broadly in the agriculture/environmental governance interface, and its oftentimes negative impacts on science and potential alternatives, can shed light on how protectionism can be made to serve ends that are at odds with environmental protection.

  13. Comparison of inorganic inhibitors of copper, nickel and copper-nickels in aqueous lithium bromide solution

    International Nuclear Information System (INIS)

    Munoz, A. Igual; Anton, J. Garcia; Guin-tilde on, J.L.; Herranz, V. Perez

    2004-01-01

    The electrochemical behavior of copper, nickel and two copper-nickel (Cu90/Ni10 and Cu70/Ni30) alloys in 850 g/L LiBr solution in the absence and presence of three different inorganic inhibitors (chromate CrO 4 2- , molybdate MoO 4 2- , and tetraborate B 4 O 7 2- ) has been studied. Differences in inhibition efficiency are discussed in terms of potentiodynamic and cyclic measurements. The best protection is obtained by adding chromate to the 850 g/L LiBr solution while the inhibition efficiencies of molybdate and tetraborate ions were not markedly high. Very aggressive anions, such as bromides, in the present experimental conditions, notably reduce the action of the less efficient molecules (molybdate and tetraborate), but not that of the most efficient ones (chromate). The results of the investigation show that the inhibiting properties depend on the nickel content in the alloy; this element improves the general corrosion resistance of the material in the sense that it shifts free corrosion potential towards more noble values and density corrosion currents towards lower levels. The nickel content in the alloy also enlarges the passivating region of the materials in chromate and molybdate-containing solution; furthermore it decreases the current passivating values to lower values. Nickel addition improves the localized corrosion resistance in the bromide media

  14. Surface Electronic Structure of Hybrid Organo Lead Bromide Perovskite Single Crystals

    KAUST Repository

    Komesu, Takashi

    2016-08-24

    The electronic structure and band dispersion of methylammonium lead bromide, CH3NH3PbBr3, has been investigated through a combination of angle-resolved photoemission spectroscopy (ARPES) and inverse photoemission spectroscopy (IPES), as well as theoretical modeling based on density functional theory. The experimental band structures are consistent with the density functional calculations. The results demonstrate the presence of a dispersive valence band in MAPbBr3 that peaks at the M point of the surface Brillouin zone. The results also indicate that the surface termination of the CH3NH3PbBr3 is the methylammonium bromide (CH3NH3Br) layer. We find our results support models that predict a heavier hole effective mass in the region of -0.23 to -0.26 me, along the Γ (surface Brillouin center) to M point of the surface Brillouin zone. The surface appears to be n-type as a result of an excess of lead in the surface region. © 2016 American Chemical Society.

  15. Aclidinium bromide plus formoterol for the treatment of chronic obstructive pulmonary disease.

    Science.gov (United States)

    Lal, Chitra; Strange, Charlie

    2015-02-01

    Drugs that target dynamic hyperinflation such as long-acting β-2 agonists and long-acting antimuscarinic antagonists form a cornerstone of chronic obstructive pulmonary disease (COPD) management. The idea of combining these two medications in a single formulation, which may potentially improve patient compliance, is novel and attractive. The pharmacologic profiles of aclidinium bromide and formoterol fumarate are discussed. However, studies to define drug interactions and alterations in the pharmacodynamics and pharmacokinetics of the fixed dose combination (FDC) of aclidinium bromide/formoterol fumarate in large populations remain unpublished. Results of Phase II and two Phase III pivotal trials, ACLIFORM/COPD and AUGMENT COPD, evaluating the FDC are discussed. Initial data for the aclidinium/formoterol inhaler appears to be promising for impacting the lung function. To define if this benefit translates into improved long-term outcomes of decreased exacerbation frequency, improved quality of life and decreased disease-specific mortality are important. The introduction of this combination will likely have a significant impact on the prescribing habits of physicians across the world.

  16. Prolonged release matrix tablet of pyridostigmine bromide: formulation and optimization using statistical methods.

    Science.gov (United States)

    Bolourchian, Noushin; Rangchian, Maryam; Foroutan, Seyed Mohsen

    2012-07-01

    The aim of this study was to design and optimize a prolonged release matrix formulation of pyridostigmine bromide, an effective drug in myasthenia gravis and poisoning with nerve gas, using hydrophilic - hydrophobic polymers via D-optimal experimental design. HPMC and carnauba wax as retarding agents as well as tricalcium phosphate were used in matrix formulation and considered as independent variables. Tablets were prepared by wet granulation technique and the percentage of drug released at 1 (Y(1)), 4 (Y(2)) and 8 (Y(3)) hours were considered as dependent variables (responses) in this investigation. These experimental responses were best fitted for the cubic, cubic and linear models, respectively. The optimal formulation obtained in this study, consisted of 12.8 % HPMC, 24.4 % carnauba wax and 26.7 % tricalcium phosphate, had a suitable prolonged release behavior followed by Higuchi model in which observed and predicted values were very close. The study revealed that D-optimal design could facilitate the optimization of prolonged release matrix tablet containing pyridostigmine bromide. Accelerated stability studies confirmed that the optimized formulation remains unchanged after exposing in stability conditions for six months.

  17. Structural, vibrational and thermal characterization of phase transformation in L-histidinium bromide monohydrate single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Moura, G.M. [Universidade Federal do Maranhão, CCSST, Imperatriz, MA, 65900-410 (Brazil); Universidade Federal do Sul e Sudeste do Pará, ICEN, Marabá, PA 68505-080 (Brazil); Carvalho, J.O. [Universidade Federal do Maranhão, CCSST, Imperatriz, MA, 65900-410 (Brazil); Instituto Federal do Tocantins, Araguaína, TO, 77.826-170 (Brazil); Silva, M.C.D.; Façanha Filho, P.F. [Universidade Federal do Maranhão, CCSST, Imperatriz, MA, 65900-410 (Brazil); Santos, A.O. dos, E-mail: adenilson1@gmail.com [Universidade Federal do Maranhão, CCSST, Imperatriz, MA, 65900-410 (Brazil)

    2015-09-01

    L-Histidinium bromide monohydrate (LHBr) single crystal is a nonlinear optical material. In this work the high temperature phase transformation and the thermal stability of single crystals of LHBr was investigated by X-ray diffraction, thermogravimetric analysis, differential thermal analysis, differential scanning calorimetry and Raman spectroscopy. The results showed the LHBr phase transformation of orthorhombic (P2{sub 1}2{sub 1}2{sub 1}) to monoclinic system (P 1 2 1) at 120 °C, with the lattice parameters a = 12.162(1) Å, b = 16.821(2) Å, c = 19.477(2) Å and β = 108.56(2)°. These techniques are complementary and confirm the structural phase transformation due to loss water of crystallization. - Highlights: • -histidinium bromide single crystal was grown by slow evaporation technique. • X-ray diffraction characterize the high-temperature phase transformation. • The structural phase transformation occur due to loss of water of crystallization. • The LHBr thermal expansion coefficients exhibit an anisotropic behavior.

  18. Integration of Bromine and Cyanogen Bromide Generators for the Continuous-Flow Synthesis of Cyclic Guanidines.

    Science.gov (United States)

    Glotz, Gabriel; Lebl, René; Dallinger, Doris; Kappe, C Oliver

    2017-10-23

    A continuous-flow process for the in situ on-demand generation of cyanogen bromide (BrCN) from bromine and potassium cyanide that makes use of membrane-separation technology is described. In order to circumvent the handling, storage, and transportation of elemental bromine, a continuous bromine generator using bromate-bromide synproportionation can optionally be attached upstream. Monitoring and quantification of BrCN generation was enabled through the implementation of in-line FTIR technology. With the Br 2 and BrCN generators connected in series, 0.2 mmol BrCN per minute was produced, which corresponds to a 0.8 m solution of BrCN in dichloromethane. The modular Br 2 /BrCN generator was employed for the synthesis of a diverse set of biologically relevant five- and six-membered cyclic amidines and guanidines. The set-up can either be operated in a fully integrated continuous format or, where reactive crystallization is beneficial, in semi-batch mode. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Liquidity Runs

    NARCIS (Netherlands)

    Matta, R.; Perotti, E.

    2016-01-01

    Can the risk of losses upon premature liquidation produce bank runs? We show how a unique run equilibrium driven by asset liquidity risk arises even under minimal fundamental risk. To study the role of illiquidity we introduce realistic norms on bank default, such that mandatory stay is triggered

  20. Phase equilibrium of (CO2 + 1-aminopropyl-3-methylimidazolium bromide + water) electrolyte system and effects of aqueous medium on CO2 solubility: Experiment and modeling

    International Nuclear Information System (INIS)

    Chen, Ying; Guo, Kaihua; Bi, Yin; Zhou, Lan

    2017-01-01

    Highlights: • Phase and chemical equilibrium data for (CO 2 + [APMIm]Br + H 2 O) electrolyte system. • A modified eNRTL model for CO 2 solubility in the amino-based IL aqueous solution. • Effects of aqueous medium on both chemical and physical dissolution of CO 2 . • The correlative coefficient, R s ∗ , for the Henry’s constant of the solution. • New parameters for the segments interaction and the chemical equilibrium constants. - Abstract: New experimental data for solubility of carbon dioxide (CO 2 ) in the aqueous solution of 1-aminopropyl-3-methylimidazolium bromide ([APMIm]Br) with four different water mass fractions (0.559, 0.645, 0.765 and 0.858) at T = (278.15–348.15) K with an interval of T = 10 K and p = (0.1237–6.9143) MPa were presented. The electrolyte nonrandom two-liquid (eNRTL) model was modified to be applicable for an ionic liquid (IL) aqueous solution system, by introducing an idle factor β to illustrate the association effect of IL molecules. A solution Henry’s constant for CO 2 solubility in the IL aqueous solution was defined by introducing a correlative coefficient R s ∗ . The vapor-liquid phase equilibrium of the [APMIm]Br-H 2 O-CO 2 ternary system was successfully calculated with the modified eNRTL model. The chemical and physical mechanisms for the ionized CO 2 formation and the molecular CO 2 dissolved in the solution were identified. The effects of aqueous medium on both chemical and physical dissolution of CO 2 in the [APMIm]Br aqueous solution were studied, and a considerable enhancement of the solubility of CO 2 with increase of the water content in the solution was observed.

  1. Bromide as a tracer for studying water movement and nitrate displacement in soils: comparison with stable isotope tracers; Bromid als Tracer zur Untersuchung der Wasserbewegung und der Nitratverlagerung in Boeden: Vergleich mit stabilisotopen Tracern

    Energy Technology Data Exchange (ETDEWEB)

    Russow, R.; Knappe, S. [UFZ - Umweltforschungszentrum Leipzig-Halle GmbH, Bad Lauchstaedt (Germany). Sektion Bodenforschung

    1999-02-01

    Tracers are an ideal means of studying water movement and associated nitrate displacement. Often bromide is preferred as a tracer because it is considered a representative tracer for water and because, being a conservative tracer (i.e. not involved in chemical and biological soil processes), it can be used for studying anion transport in soils. Moreover, it is less expensive and easier to measure than the stable isotopes deuterium and {sup 15}N. Its great advantage over radioactive tracers (e.g. tritium), which outweighs their extreme sensitivity and ease of measurement and which it has in common with stable isotopes, is that it does not require radiation protection measures. However, there are also constraints on the use of bromide as a tracer in soil/water/plant systems. Our own studies on different soils using D{sub 2}O, bromide and [{sup 15}N]-nitrate in lysimeters suggest that the above assumptions on bromide tracers need not always be valid under conditions as they prevail in biologically active soils. As the present paper shows, these studies permit a good assessment of the possibilities and limits to these tracers. [Deutsch] Fuer die Untersuchung der Wasserbewegung sowie der daran gekoppelten Nitrat-Verlagerung ist der Einsatz von Tracern das Mittel der Wahl. Dabei wird Bromid als Tracer haeufig bevorzugt, da es allgemein als ein repraesentativer Tracer fuer Wasser und als konservativer Tracer (nicht involviert in chemische und biologische Bodenprozesse) zur Untersuchung des Anionentransportes in Boeden angesehen wird und es gegenueber den stabilen Isotopen Deuterium und {sup 15}N billiger und einfacher zu bestimmen ist. Gegenueber den radioaktiven Tracern (z.B. Tritium), die zwar sehr empfindlich und einfach messbar sind, besteht der grosse Vorteil, dass, wie bei den stabilen Isotopen, keine Strahlenschutzmassnahmen ergriffen werden muessen. Es gibt jedoch auch einschraenkende Hinweise fuer die Verwendung von Bromid als Tracer im System Boden

  2. Managing liquidity

    DEFF Research Database (Denmark)

    Pokutta, Sebastian; Schmaltz, Christian

    2011-01-01

    Large banking groups face the question of how to optimally allocate and generate liquidity: in a central liquidity hub or in many decentralized branches. We translate this question into a facility location problem under uncertainty. We show that volatility is the key driver behind (de......-)centralization. We provide an analytical solution for the 2-branch model and show that a liquidity center can be interpreted as an option on immediate liquidity. Therefore, its value can be interpreted as the price of information, i.e., the price of knowing the exact demand. Furthermore, we derive the threshold...... above which it is advantageous to open a liquidity center and show that it is a function of the volatility and the characteristic of the bank network. Finally, we discuss the n-branch model for real-world banking groups (10-60 branches) and show that it can be solved with high granularity (100 scenarios...

  3. The Research on Programmable Control System of Lithium-Bromide Absorption Refrigerating Air Conditioner Based on the Network

    Directory of Open Access Journals (Sweden)

    Sun Lunan

    2016-01-01

    Full Text Available This article regard the solar lithium-bromide absorption refrigerating air conditioning system as the research object, and it was conducting adequate research of the working principle of lithium bromide absorption refrigerating machine, also it was analyzing the requirements of control system about solar energy air conditioning. Then the solar energy air conditioning control system was designed based on PLC, this system was given priority to field bus control system, and the remote monitoring is complementary, which was combining the network remote monitoring technology. So that it realized the automatic control and intelligent control of new lithium bromide absorption refrigerating air conditioning system with solar energy, also, it ensured the control system can automatically detect and adjust when the external conditions was random changing, to make air conditioning work effectively and steadily, ultimately ,it has great research significance to research the air conditioning control system with solar energy.

  4. Characterization of the corrosion products formed on mild steel in acidic medium with N-octadecylpyridinium bromide as corrosion inhibitor

    Energy Technology Data Exchange (ETDEWEB)

    Nava, N., E-mail: tnava@imp.mx; Likhanova, N. V. [Direccion de Investigacion y Posgrado, Instituto Mexicano del Petroleo (Mexico); Olivares-Xometl, O. [Benemerita Universidad Autonoma de Puebla, Facultad de Ingenieria Quimica (Mexico); Flores, E. A. [Direccion de Investigacion y Posgrado, Instituto Mexicano del Petroleo (Mexico); Lijanova, I. V. [CIITEC, Instituto Politecnico Nacional (Mexico)

    2011-11-15

    The characterization of the corrosion products formed on mild steel SAE 1018 after 2 months exposure in aqueous sulfuric acid with and without corrosion inhibitor N-octadecylpyridinium bromide has been carried out by means of transmission {sup 57}Fe Moessbauer spectroscopy and X-ray powder diffraction (XRD). The major constituent of the rust formed in this environment without corrosion inhibitor is goethite ({alpha}-FeOOH). The samples with N-octadecylpyridinium bromide contain rozenite and large amounts of melanterite in the corrosion layers.

  5. Synthesis of an Ionic Liquid and Its Application as Template for the Preparation of Mesoporous Material MCM-41: A Comprehensive Experiment for Undergraduate Students

    Science.gov (United States)

    Hu, Jun; Yin, Jinxiang; Lin, Tianshu; Li, Guangtao

    2012-01-01

    A new solvent-free microwave experiment to synthesize the ionic liquid 1-hexadecyl-3-methylimidazolium bromide (HDMIm-Br) in high yield is presented. The structure is confirmed by IR and [superscript 1]H NMR spectra. HDMIm-Br is then used to prepare an organic-inorganic mesoporous material MCM-41. The microscopic arrangements of mesoporous…

  6. Solid-liquid phase equilibrium in the systems of LiBr-H2O and LiCl-H2O

    Czech Academy of Sciences Publication Activity Database

    Pátek, Jaroslav; Klomfar, Jaroslav

    2006-01-01

    Roč. 250, - (2006), s. 138-149 ISSN 0378-3812 Institutional research plan: CEZ:AV0Z20760514 Keywords : salt-water system * solubility * solid-liquid system * lithium bromide * litthium chloride Subject RIV: BJ - Thermodynamics Impact factor: 1.680, year: 2006

  7. Designing solid-liquid interphases for sodium batteries

    KAUST Repository

    Choudhury, Snehashis

    2017-10-06

    Secondary batteries based on earth-abundant sodium metal anodes are desirable for both stationary and portable electrical energy storage. Room-temperature sodium metal batteries are impractical today because morphological instability during recharge drives rough, dendritic electrodeposition. Chemical instability of liquid electrolytes also leads to premature cell failure as a result of parasitic reactions with the anode. Here we use joint density-functional theoretical analysis to show that the surface diffusion barrier for sodium ion transport is a sensitive function of the chemistry of solid–electrolyte interphase. In particular, we find that a sodium bromide interphase presents an exceptionally low energy barrier to ion transport, comparable to that of metallic magnesium. We evaluate this prediction by means of electrochemical measurements and direct visualization studies. These experiments reveal an approximately three-fold reduction in activation energy for ion transport at a sodium bromide interphase. Direct visualization of sodium electrodeposition confirms large improvements in stability of sodium deposition at sodium bromide-rich interphases.

  8. Studies on nitrile rubber degradation in zinc bromide completion fluid and its prevention by surface fluorination

    Science.gov (United States)

    Vega-Cantu, Yadira Itzel

    Poly(acrylonitrile-co-butadiene) or nitrile-butadiene rubber (NBR) is frequently used as an O-ring material in the oil extraction industry due to its excellent chemical properties and resistance to oil. However, degradation of NBR gaskets is known to occur during the well completion and oil extraction process where packers are exposed to completion fluids such as ZnBr2 brine. Under these conditions NBR exhibits accelerated chemical degradation resulting in embrittlement and cracking. Samples of NBR, poly(acrylonitrile) (PAN) and poly(butadiene) (PB) have been exposed to ZnBr2 based completion fluid, and analyzed by ATR and diffuse reflectance IR. Analysis shows the ZnBr2 based completion fluid promotes hydrolysis of the nitrile group to form amides and carboxylic groups. Analysis also shows that carbon-carbon double bonds in NBR are unaffected after short exposure to zinc bromide based completion fluid, but are quickly hydrolyzed in acidic bromide mixtures. Although fluoropolymers have excellent chemical resistance, their strength is less than nitrile rubber and replacing the usual gasket materials with fluoroelastomers is expensive. However, a fluoropolymer surface on a nitrile elastomer can provide the needed chemical resistance while retaining their strength. In this study, we have shown that this can be achieved by direct fluorination, a rather easy and inexpensive process. Samples of NBR O-rings have been fluorinated by exposure to F2 and F2/HF mixtures at various temperatures. Fluorination with F 2 produces the desired fluoropolymer layer; however, fluorination by F2/HF mixtures gave a smoother fluorinated layer at lower temperatures and shorter times. Fluorinated samples were exposed to ZnBr2 drilling fluid and solvents. Elemental analysis shows that the fluorinated layer eliminates ZnBr2 diffusion into the NBR polymeric matrix. It was also found that surface fluorination significantly retards the loss of mechanical properties such as elasticity, tensile

  9. COPD patient satisfaction with ipratropium bromide/albuterol delivered via Respimat: a randomized, controlled study

    Directory of Open Access Journals (Sweden)

    Ferguson GT

    2013-03-01

    Full Text Available Gary T Ferguson,1 Mo Ghafouri,2 Luyan Dai,2 Leonard J Dunn31Pulmonary Research Institute of Southeast Michigan, Livonia, MI, USA; 2Boehringer Ingelheim Pharmaceuticals, Inc, Ridgefield, CT, USA; 3Clinical Research of West Florida, Inc, Clearwater, FL, USABackground: Ipratropium bromide/albuterol Respimat inhaler (CVT-R was developed as an environmentally friendly alternative to ipratropium bromide/albuterol metered-dose inhaler (CVT-MDI, which uses a chlorofluorocarbon propellant.Objective: The objective of this study was to evaluate patient satisfaction, device usage, and long-term safety of CVT-R compared to CVT-MDI, and to the simultaneous administration of ipratropium bromide hydrofluoroalkane (HFA; I and albuterol HFA (A metered-dose inhalers as dual monotherapies (I + A.Design: This is a 48-week, open-label, randomized, active-controlled, parallel-group study (n = 470 comparing CVT-R to CVT-MDI and to I + A.Participants: Patients were at least 40 years of age, diagnosed with chronic obstructive pulmonary disease (COPD, and current or exsmokers.Interventions: Patients were randomized to receive: (1 CVT-R, one inhalation four times daily (QID; or (2 CVT-MDI, two inhalations QID; or (3 I + A two inhalations of each inhaler QID.Main measures: Patient Satisfaction and Preference Questionnaire (PASAPQ performance score (primary endpoint and adverse events.Key results: PASAPQ performance score was significantly higher (CVT-R versus CVT-MDI, 9.6; and CVT-R versus I + A, 6.2; both P < 0.001 when using CVT-R compared to CVT-MDI or I + A at all visits starting from week 3, while CVT-MDI and I + A treatment groups were similar. Time to first COPD exacerbation was slightly longer in the CVT-R group compared to the other treatment groups, although it did not reach statistical significance (CVT-R versus CVT-MDI, P = 0.57; CVT-R versus I + A, P = 0.22. Rates of withdrawal and patient refusal to continue treatment were lower in CVT-R compared with CVT

  10. Purification of the labeled cyanogen bromide peptides of the. cap alpha. polypeptide from sodium and potassium ion-activated adenosinetriphosphatase modified with N-(/sup 3/H)ethylmaleimide

    Energy Technology Data Exchange (ETDEWEB)

    Le, D.T.

    1985-01-01

    Sodium and potassium ion-activated adenosinetriphosphatase, isolated from canine kidney, was reacted with N-(/sup 3/H)ethylmaleimide under three different conditions, defined by particular concentrations of ligands for the enzyme, such that after the same amount of time the remaining activity of then enzyme varied from 90% to 30%. The conformation of the enzyme also differed among the three conditions. In all cases, the ..cap alpha..-polypeptide was purified and subjected to cyanogen bromide digestion. Two distinct, radioactive peptides were separated by gel filtration of the cyanogen bromide digest on a column of Sephadex LH-60 equilibrated with 95% ethanol: 88% formic acid:4:1. One of the radioactive peptides was shown to contain the sulfhydryl residue whose reaction with N-ethylmaleimide inactivates the enzyme. The other radioactive peptide contained a sulfhydryl residue that seems to react with N-ethylmaleimide only when the binding site for ATP is not occupied. Alkylation of this residue, however, does not result in inactivation of enzyme. Both peptides were purified further by high-pressure liquid chromatography, and their amino-terminal sequences were determined by the manual dansyl-Edman or solid-phase techniques. The peptide containing the sulfhydryl protected by ATP has, as its amino terminus, the lysine that reacts exclusively with fluorescein-5'-isothiocyanate.

  11. Liquid explosives

    CERN Document Server

    Liu, Jiping

    2015-01-01

    The book drawing on the author's nearly half a century of energetic materials research experience intends to systematically review the global researches on liquid explosives. The book focuses on the study of the conception, explosion mechanism, properties and preparation of liquid explosives. It provides a combination of theoretical knowledge and practical examples in a reader-friendly style. The book is likely to be interest of university researchers and graduate students in the fields of energetic materials, blasting engineering and mining.

  12. Thermophysical properties of phosphonium-based ionic liquids

    Science.gov (United States)

    Bhattacharjee, Arijit; Lopes-da-Silva, José A.; Freire, Mara G.; Coutinho, João A. P.; Carvalho, Pedro J.

    2015-01-01

    Experimental data for density, viscosity, refractive index and surface tension of four phosphonium-based ionic liquids were measured in the temperature range between (288.15 and 353.15) K and at atmospheric pressure. The ionic liquids considered include tri(isobutyl) methylphosphonium tosylate, [Pi(444)1][Tos], tri(butyl)methylphosphonium methylsulfate, [P4441][CH3SO4], tri(butyl)ethylphosphonium diethylphosphate, [P4442][(C2H5O)2PO2], and tetraoctylphosphonium bromide, [P8888][Br]. Additionally, derivative properties, such as the isobaric thermal expansion coefficient, the surface thermodynamic properties and the critical temperatures for the investigated ionic liquids were also estimated and are presented and discussed. Group contribution methods were evaluated and fitted to the density, viscosity and refractive index experimental data. PMID:26435574

  13. Thermophysical properties of phosphonium-based ionic liquids.

    Science.gov (United States)

    Bhattacharjee, Arijit; Lopes-da-Silva, José A; Freire, Mara G; Coutinho, João A P; Carvalho, Pedro J

    2015-08-25

    Experimental data for density, viscosity, refractive index and surface tension of four phosphonium-based ionic liquids were measured in the temperature range between (288.15 and 353.15) K and at atmospheric pressure. The ionic liquids considered include tri(isobutyl) methylphosphonium tosylate, [P i (444)1 ][Tos], tri(butyl)methylphosphonium methylsulfate, [P 4441 ][CH 3 SO 4 ], tri(butyl)ethylphosphonium diethylphosphate, [P 4442 ][(C 2 H 5 O) 2 PO 2 ], and tetraoctylphosphonium bromide, [P 8888 ][Br]. Additionally, derivative properties, such as the isobaric thermal expansion coefficient, the surface thermodynamic properties and the critical temperatures for the investigated ionic liquids were also estimated and are presented and discussed. Group contribution methods were evaluated and fitted to the density, viscosity and refractive index experimental data.

  14. Determination of critical micelle concentration of cetyltrimethylammonium bromide: Different procedures for analysis of experimental data

    Directory of Open Access Journals (Sweden)

    Goronja Jelena M.

    2016-01-01

    Full Text Available Conductivity of two micellar systems was measured in order to determine critical micelle concentration (CMC of cetyltrimethylammonium bromide (CTAB. Those systems were: CTin water and CTin binary mixture acetonitrile (ACN-water. Conductivity (κ-concentration (c data were treated by four different methods: conventional method, differential methods (first and second derivative and method of integration (methods A-D, respectively. As CTin water micellar system shows a sharp transition between premicellar and postmicellar part of the κ/c curve, any of the applied methods gives reliable CMC values and there is no statistically significant difference between them. However, for CTin ACN-water mixture micellar system the integration method for CMC determination is recommended due to a weak curvature of κ/c plot.

  15. Purification of Sarcocystis neurona sporocysts from opossum (Didelphis virginiana) using potassium bromide discontinuous density gradient centrifugation.

    Science.gov (United States)

    Elsheikha, Hany M; Murphy, Alice J; Fitzgerald, Scott D; Mansfield, Linda S; Massey, Jeffrey P; Saeed, Mahdi A

    2003-06-01

    This report describes a new, inexpensive procedure for the rapid and efficient purification of Sarcocystis neurona sporocysts from opossum small intestine. S. neurona sporocysts were purified using a discontinuous potassium bromide density gradient. The procedure provides a source of sporocyst wall and sporozoites required for reliable biochemical characterization and for immunological studies directed at characterizing antigens responsible for immunological responses by the host. The examined isolates were identified as S. neurona using random amplified polymorphic DNA primers and restriction endonuclease digestion assays. This method allows the collection of large numbers of highly purified S. neurona sporocysts without loss of sporocyst viability as indicated by propidium iodide permeability and cell culture infectivity assays. In addition, this technique might also be used for sporocyst purification of other Sarcocystis spp.

  16. Characterization of potassium bromide crystals grown in the aqueous solution of picric acid

    Energy Technology Data Exchange (ETDEWEB)

    Maheswari, J. Uma, E-mail: umak.anand@gmail.com [Department of Physics, The M.D.T.Hindu College, Tirunelveli 627010, Tamilnadu (India); Krishnan, C. [Department of Physics, Arignar Anna College, Aralvoymoli 629301, Tamilnadu (India); Kalyanaraman, S. [Physics Research Centre, Sri Paramakalyani College, Alwarkurichi 627412, Tamilnadu (India); Selvarajan, P. [Department of Physics, Aditanar College of Arts and Science, Tiruchendur 628216, Tamilnadu (India)

    2016-12-01

    Potassium bromide crystals were grown in the aqueous solution of picric acid by slow evaporation technique at room temperature. X-ray Diffraction (XRD) analysis ensures that the grown sample is in Fm3m space group and FCC structure. Energy Dispersive X-ray Spectroscopy (EDX) reveals the presence of elements in the title compound. UV–Vis-NIR spectrum reveals that the grown sample is a promising nonlinear optical (NLO) material. FTIR analysis confirms the functional groups present in the sample. The thermogravimetric (TG) and differential thermogravimetric (DTA) analyses ensure that the sample material is thermally stable up to 160 °C. The second harmonic efficiency of the sample is 1.3 times greater than that of standard KDP. The mechanical strength of the grown sample is estimated by Vickers microhardness tester. The electrical properties were investigated by impedance analysis and the results of various studies of the grown crystals are discussed.

  17. Investigation of thermodynamic parameters of cetyl pyridinium bromide sorption onto ZSM-5 and natural clinoptilolite

    International Nuclear Information System (INIS)

    Ghiaci, M.; Kia, R.; Kalbasi, R.J.

    2004-01-01

    A study was undertaken to determine the influence of temperature and surfactant concentration on the adsorption of cetyl pyridinium bromide on two ZSM-5 zeolites, and on natural clinoptilolite. The effect of temperature on adsorption and thermodynamic properties was investigated by making measurements at (297, 303, 307, 313) K. The results show that the calculated curves from the general isotherm equation can represent the experimental data very well up to T=313 K. Based on the calculation of the thermodynamics of adsorption, it is evident that the principle contribution to the ΔG compfn hm of negative value is the large positive value of ΔS compfn hm (36 to 52 J · mol -1 ), whereas ΔH compfn hm is positive and in the range of 1 to 7 kJ · mol -1 . Therefore, similar to the micellisation in bulk solution, the second step of surfactant adsorption is an entropy-driven process

  18. Interaction between dimethyldioctadecylammonium bromide-modified PLGA microspheres and hyaluronic acid

    Science.gov (United States)

    Mulia, Kamarza; Devi, Krisanti, Elsa

    2017-02-01

    In application of intravitreal injection, an extended drug delivery system is desired so that the frequency of injection to treat diabetic retinopathy may be reduced. Poly(lactic-co-glycolic acid) polymer (PLGA) was used to encapsulate a model drug in the form of microspheres. The zeta potential of dimethyldioctadecylammonium bromide (DDAB)-modified PLGA microspheres in water was proportional to the DDAB concentration used in the preparation step, up to +57.8 mV. The scanning electron microscope pictures and the zeta potential data (SEM) confirmed that the surface of the PLGA has been modified by the cationic surfactant and that electrostatic interaction between the positively charged microspheres and the negatively charged vitreous were present.

  19. Bromide (Br)--Based Synthesis of Ag Nanocubes with High-Yield.

    Science.gov (United States)

    Wu, Fan; Wang, Wenhui; Xu, Zhongfeng; Li, Fuli

    2015-06-09

    The geometry of metal nanoparticles greatly affects the properties of the localized surface plasmon resonance and surface-enhanced Raman scattering. The synthesis of metal nanoparticles with controllable geometry has thus attracted extensive attentions. In this work, we report a modified polyol synthesis approach of silver (Ag) nanocubes through tuning the concentration of bromide ions (Br(-) ions). We have systematically investigated the effect of Br(-) ions in the polyol process, and find that higher concentration of Br(-) ions can enhance oxidative etching effect, which is the dominative factor in determining nanostructure geometry. Therefore, one can realize control over nanostructure geometry by manipulating the concentration of Br(-) ions. Our work provides an effective approach to control the shape of metallic nanostructures for potential applications.

  20. Bromide (Br) - Based Synthesis of Ag Nanocubes with High-Yield

    Science.gov (United States)

    Wu, Fan; Wang, Wenhui; Xu, Zhongfeng; Li, Fuli

    2015-01-01

    The geometry of metal nanoparticles greatly affects the properties of the localized surface plasmon resonance and surface-enhanced Raman scattering. The synthesis of metal nanoparticles with controllable geometry has thus attracted extensive attentions. In this work, we report a modified polyol synthesis approach of silver (Ag) nanocubes through tuning the concentration of bromide ions (Br− ions). We have systematically investigated the effect of Br− ions in the polyol process, and find that higher concentration of Br− ions can enhance oxidative etching effect, which is the dominative factor in determining nanostructure geometry. Therefore, one can realize control over nanostructure geometry by manipulating the concentration of Br− ions. Our work provides an effective approach to control the shape of metallic nanostructures for potential applications. PMID:26058050

  1. Ammonia-hydrogen bromide and ammonia-hydrogen iodide complexes: anion photoelectron and ab initio studies.

    Science.gov (United States)

    Eustis, S N; Whiteside, A; Wang, D; Gutowski, M; Bowen, K H

    2010-01-28

    The ammonia-hydrogen bromide and ammonia-hydrogen iodide, anionic heterodimers were studied by anion photoelectron spectroscopy. In complementary studies, these anions and their neutral counterparts were also investigated via ab initio theory at the coupled cluster level. In both systems, neutral NH(3)...HX dimers were predicted to be linear, hydrogen-bonded complexes, whereas their anionic dimers were found to be proton-transferred species of the form, (NH(4)(+)X(-))(-). Both experimentally measured and theoretically predicted vertical detachment energies (VDE) are in excellent agreement for both systems, with values for (NH(4)(+)Br(-))(-) being 0.65 and 0.67 eV, respectively, and values for (NH(4)(+)I(-))(-) being 0.77 and 0.81 eV, respectively. These systems are discussed in terms of our previous study of (NH(4)(+)Cl(-))(-).

  2. Self-made silver-bromide-based emulsions for users in holography: manufacturing, processing, and application

    Science.gov (United States)

    Duenkel, Lothar; Eichler, Juergen; Ackermann, Gerhard; Schneeweiss, Claudia

    2004-06-01

    Holography is the most fascinating technology for three-dimensional imaging. But despite of many decades of research, the seek for an ideal recording material has never been given up. From all ultra-fine materials, silver bromide emulsions with very small grain sizes have the highest sensitivity. In recent years however, many traditional manufacturers discontinued their production. Meanwhile, newcomers succeeded in manufacturing emulsions which are very suitable for holography, concerning extremely high resolution, brigthness and sensitivity1. But two problems may still linger: First, the deficient market situation for production and application on this field. Second, the reputation of the system of being extremely complicated for laboratory preparation. In such a crucial situation, the authors have succeeded in presenting a laboratory procedure for making do-it-yourself materials available to any expert who is well versed in holography, and who disposes of normal darkroom equipment2. The methodology is based on precipitation using the traditional double-jet method according to Thiry and predecessors3. But sensitization is carried out by a diffusion process according to the procedure as proposed by Blyth et al.4 Thus, precipitation and coating on one side and sensitization on the other one are separated strictly from one another. Efficient desaltation is an important process too, warranting the high opto-mechanical quality of the layer. The material has been sensitzed for HeNe-Laser radiation (632,8 nm) only up to now. The mean diameter of the silver bromide grains is about 15 nm, as determined by transmission electron microscopy (TEM). Phillips-Bjelkhagen Ultimate (PBU) or Fe3+ rehalogenation bleach are applied successfully5-6. In final result, a new generation of holograms with ultra-high resolution, proper contrast, excellent sharpness and light brightness has been obtained. Holography belongs to an advancing technology where the search for an ideal recording

  3. Efficient loading of primary alcohols onto a solid phase using a trityl bromide linker

    DEFF Research Database (Denmark)

    Crestey, François; Ottesen, Lars Korsgaard; Jaroszewski, Jerzy Witold

    2008-01-01

    The Letter describes an improved, rapid and mild strategy for the loading of primary alcohols onto a polystyrene trityl resin via a highly reactive trityl bromide linker. This protocol facilitates an efficient resin loading even of acid-sensitive or heat-labile alcohols, which otherwise require...... expensive or non-commercial resin types. Secondary alcohols were only attached in moderate to low yields, while attempts to load a tertiary alcohol expectedly failed. Importantly, selective attachment of diols via a primary alcohol group in the presence of more hindered alcohol groups proved possible....... The effects of activation time and reagent excess as well as alcohol structure were investigated. This improved method provides a convenient access to O-linked resin-bound N-Fmoc-protected amino alcohols that may be employed in SPS of peptides with C-terminal alcohol functionalities. In the case...

  4. A copper bromide vapour laser with a high pulse repetition rate

    International Nuclear Information System (INIS)

    Shiyanov, D V; Evtushenko, Gennadii S; Sukhanov, V B; Fedorov, V F

    2002-01-01

    The results of an experimental study of a copper bromide vapour laser with a discharge-channel diameter above 2.5 cm and a high pump-pulse repetition rate are presented. A TGU1-1000/25 high-power tacitron used as a switch made it possible to obtain for the first time a fairly high output radiation power for pump-pulse repetition rates exceeding 200 kHz. At a maximum pump-pulse repetition rate of 250 kHz achieved in a laser tube 2.6 cm in diameter and 76 cm long, the output power was 1.5 W. The output powers of 3 and 10.5 W were reached for pump-pulse repetition rates of 200 and 100 kHz, respectively. These characteristics were obtained without circulating a buffer gas and (or) low-concentration active impurities through the active volume. (active media. lasers)

  5. PREFACE: Functionalized Liquid Liquid Interfaces

    Science.gov (United States)

    Girault, Hubert; Kornyshev, Alexei A.; Monroe, Charles W.; Urbakh, Michael

    2007-09-01

    Most natural processes take place at interfaces. For this reason, surface science has been a focal point of modern research. At solid-liquid interfaces one can induce various species to adsorb or react, and thus may study interactions between the substrate and adsorbates, kinetic processes, optical properties, etc. Liquid-liquid interfaces, formed by immiscible liquids such as water and oil, have a number of distinctive features. Both sides of the interface are amenable to detailed physical and chemical analysis. By chemical or electrochemical means, metal or semiconductor nanoparticles can be formed or localised at the interface. Surfactants can be used to tailor surface properties, and also to place organic molecular or supermolecular constructions at the boundary between the liquids. Electric fields can be used to drive ions from one fluid to another, or even change the shape of the interface itself. In many cases, both liquids are optically transparent, making functionalized liquid-liquid interfaces promising for various optical applications based on the transmission or reflection of light. An advantage common to most of these systems is self-assembly; because a liquid-liquid interface is not mechanically constrained like a solid-liquid interface, it can easily access its most stable state, even after it has been driven far from equilibrium. This special issue focuses on four modes of liquid-liquid interfacial functionalization: the controlled adsorption of molecules or nanoparticles, the formation of adlayers or films, electrowetting, and ion transfer or interface-localized reactions. Interfacial adsorption can be driven electrically, chemically, or mechanically. The liquid-liquid interface can be used to study how anisotropic particles orient at a surface under the influence of a field, how surfactants interact with other adsorbates, and how nanoparticles aggregate; the transparency of the interface also makes the chirality of organic adsorbates amenable to

  6. Purification of labeled cyanogen bromide peptides of the alpha polypeptide from sodium ion and potassium ion activated adenosinetriphosphatase modified with N-(/sup 3/H)ethylmaleimide

    Energy Technology Data Exchange (ETDEWEB)

    Le, D.T.

    1986-05-06

    Sodium ion and potassium ion activated adenosinetriphosphatase, isolated from canine kidney, was reacted with N-(/sup 3/H)ethylmaleimide while it was poised in three different conformations, ostensibly E2-P, E2, and E1, respectively. These assignments were made from a consideration of the particular concentrations of ligands in the respective alkylation mixtures. After a 30-min reaction, the remaining enzymatic activity was found to vary among these three different samples from 90 to 30% of that of unalkylated controls. In all cases, the alpha polypeptide was purified and subjected to digestion with cyanogen bromide, and in each digest the same two distinct radioactive peptides were identified and purified by gel filtration on a column of Sephadex LH-60. The incorporation of N-(/sup 3/H)ethylmaleimide into one of these two peptides correlated closely with enzymatic inactivation, while the incorporation into the other was most extensive when the portion of the active site to which ATP binds was unoccupied. Alkylation of the residue within the latter peptide, however, does not result in inactivation of the enzyme. Both peptides were further purified by high-pressure liquid chromatography, and their amino-terminal sequences were determined by manual dansyl Edman or solid-phase techniques. The peptide containing the sulfhydryl protected by ATP has, as its amino terminus, the lysine that reacts exclusively with fluoresceinyl 5'-isothiocyanate.

  7. Purification of labeled cyanogen bromide peptides of the alpha polypeptide from sodium ion and potassium ion activated adenosinetriphosphatase modified with N-[3H]ethylmaleimide

    International Nuclear Information System (INIS)

    Le, D.T.

    1986-01-01

    Sodium ion and potassium ion activated adenosinetriphosphatase, isolated from canine kidney, was reacted with N-[ 3 H]ethylmaleimide while it was poised in three different conformations, ostensibly E2-P, E2, and E1, respectively. These assignments were made from a consideration of the particular concentrations of ligands in the respective alkylation mixtures. After a 30-min reaction, the remaining enzymatic activity was found to vary among these three different samples from 90 to 30% of that of unalkylated controls. In all cases, the alpha polypeptide was purified and subjected to digestion with cyanogen bromide, and in each digest the same two distinct radioactive peptides were identified and purified by gel filtration on a column of Sephadex LH-60. The incorporation of N-[ 3 H]ethylmaleimide into one of these two peptides correlated closely with enzymatic inactivation, while the incorporation into the other was most extensive when the portion of the active site to which ATP binds was unoccupied. Alkylation of the residue within the latter peptide, however, does not result in inactivation of the enzyme. Both peptides were further purified by high-pressure liquid chromatography, and their amino-terminal sequences were determined by manual dansyl Edman or solid-phase techniques. The peptide containing the sulfhydryl protected by ATP has, as its amino terminus, the lysine that reacts exclusively with fluoresceinyl 5'-isothiocyanate

  8. Catalytic cracking of slack wax with molten mixtures containing aluminum chloride and bromide. [Wax obtained in the process of dewaxing lubricating oils

    Energy Technology Data Exchange (ETDEWEB)

    Ohtsuka, Y; Oizumi, K; Tamai, Y

    1983-09-01

    The catalytic cracking of slack wax with molten mixtures of AlCl/sub 3/ (aluminum chloride) and AlBr/sub 3/ (aluminum bromide) was investigated in an atmospheric semi-batch reactor at low temperatures of 100 to 160/sup 0/C. The cracking rate was proportional to the amount of unreacted wax. The conversion at 135/sup 0/C reached 25 wt % under typical reaction conditions. About 95 wt % of the cracking products consisted of isobutane, 2-methylbutane, and methylpentanes, ca. 50% of these isoparaffins being isobutane. The difference in cracking activity between this catalyst and a solid acid catalyst is discussed based on the product distribution. Hardly any reaction took place without HCl, which shows that the presence of HCl is essential for this cracking. The cracking rate increased sharply with an increase in the amount of the catalyst. The rate did not depend on the composition of the AlCl/sub 3//sup -/ AlBr/sub 3/ catalyst, but the product distribution did depend on it and the content of the gasoline fraction in the products increased with an increase in the concentration of AlBr/sub 3/. The cracking residue was characterized by IR and NMR spectroscopy. The results show that the cracking reaction probably occurs heterogeneously at the interface between the liquid wax and the molten catalyst. 3 figures, 4 tables.

  9. Enhancement of Inverted Polymer Solar Cells Performances Using Cetyltrimethylammonium-Bromide Modified ZnO

    Directory of Open Access Journals (Sweden)

    Chung-Kai Wu

    2018-03-01

    Full Text Available In this study, the performance and stability of inverted bulk heterojunction (BHJ polymer solar cells (PSCs is enhanced by doping zinc oxide (ZnO with 0–6 wt % cetyltrimethylammonium bromide (CTAB in the sol-gel ZnO precursor solution. The power conversion efficiency (PCE of the optimized 3 wt % CTAB-doped ZnO PSCs was increased by 9.07%, compared to a PCE of 7.31% for the pristine ZnO device. The 0–6 wt % CTAB-doped ZnO surface roughness was reduced from 2.6 to 1 nm and the number of surface defects decreased. The X-ray photoelectron spectroscopy binding energies of Zn 2p3/2 (1021.92 eV and 2p1/2 (1044.99 eV shifted to 1022.83 and 1045.88 eV, respectively, which is related to strong chemical bonding via bromide ions (Br− that occupy oxygen vacancies in the ZnO lattice, improving the PCE of PSCs. The concentration of CTAB in ZnO significantly affected the work function of PSC devices; however, excessive CTAB increased the work function of the ZnO layer, resulting from the aggregation of CTAB molecules. In addition, after a 120-hour stability test in the atmosphere with 40% relative humidity, the inverted device based on CTAB-doped ZnO retained 92% of its original PCE and that based on pristine ZnO retained 68% of its original PCE. The obtained results demonstrate that the addition of CTAB into ZnO can dramatically influence the optical, electrical, and morphological properties of ZnO, enhancing the performance and stability of BHJ PSCs.

  10. Bromide supplementation exacerbated the renal dysfunction, injury and fibrosis in a mouse model of Alport syndrome.

    Science.gov (United States)

    Yokota, Tsubasa; Omachi, Kohei; Suico, Mary Ann; Kojima, Haruka; Kamura, Misato; Teramoto, Keisuke; Kaseda, Shota; Kuwazuru, Jun; Shuto, Tsuyoshi; Kai, Hirofumi

    2017-01-01

    A seminal study recently demonstrated that bromide (Br-) has a critical function in the assembly of type IV collagen in basement membrane (BM), and suggested that Br- supplementation has therapeutic potential for BM diseases. Because salts of bromide (KBr and NaBr) have been used as antiepileptic drugs for several decades, repositioning of Br- for BM diseases is probable. However, the effects of Br- on glomerular basement membrane (GBM) disease such as Alport syndrome (AS) and its impact on the kidney are still unknown. In this study, we administered daily for 16 weeks 75 mg/kg or 250 mg/kg (within clinical dosage) NaBr or NaCl (control) via drinking water to 6-week-old AS mice (mouse model of X-linked AS). Treatment with 75 mg/kg NaBr had no effect on AS progression. Surprisingly, compared with 250 mg/kg NaCl, 250 mg/kg NaBr exacerbated the progressive proteinuria and increased the serum creatinine and blood urea nitrogen in AS mice. Histological analysis revealed that glomerular injury, renal inflammation and fibrosis were exacerbated in mice treated with 250 mg/kg NaBr compared with NaCl. The expressions of renal injury markers (Lcn2, Lysozyme), matrix metalloproteinase (Mmp-12), pro-inflammatory cytokines (Il-6, Il-8, Tnf-α, Il-1β) and pro-fibrotic genes (Tgf-β, Col1a1, α-Sma) were also exacerbated by 250 mg/kg NaBr treatment. Notably, the exacerbating effects of Br- were not observed in wild-type mice. These findings suggest that Br- supplementation needs to be carefully evaluated for real positive health benefits and for the absence of adverse side effects especially in GBM diseases such as AS.

  11. Multimetallic catalysed cross-coupling of aryl bromides with aryl triflates

    Science.gov (United States)

    Ackerman, Laura K. G.; Lovell, Matthew M.; Weix, Daniel J.

    2015-08-01

    The advent of transition-metal catalysed strategies for forming new carbon-carbon bonds has revolutionized the field of organic chemistry, enabling the efficient synthesis of ligands, materials, and biologically active molecules. In cases where a single metal fails to promote a selective or efficient transformation, the synergistic cooperation of two distinct catalysts--multimetallic catalysis--can be used instead. Many important reactions rely on multimetallic catalysis, such as the Wacker oxidation of olefins and the Sonogashira coupling of alkynes with aryl halides, but this approach has largely been limited to the use of metals with distinct reactivities, with only one metal catalyst undergoing oxidative addition. Here, we demonstrate that cooperativity between two group 10 metal catalysts--(bipyridine)nickel and (1,3-bis(diphenylphosphino)propane)palladium--enables a general cross-Ullmann reaction (the cross-coupling of two different aryl electrophiles). Our method couples aryl bromides with aryl triflates directly, eliminating the use of arylmetal reagents and avoiding the challenge of differentiating between multiple carbon-hydrogen bonds that is required for direct arylation methods. Selectivity can be achieved without an excess of either substrate and originates from the orthogonal reactivity of the two catalysts and the relative stability of the two arylmetal intermediates. While (1,3-bis(diphenylphosphino)propane)palladium reacts preferentially with aryl triflates to afford a persistent intermediate, (bipyridine)nickel reacts preferentially with aryl bromides to form a transient, reactive intermediate. Although each catalyst forms less than 5 per cent cross-coupled product in isolation, together they are able to achieve a yield of up to 94 per cent. Our results reveal a new method for the synthesis of biaryls, heteroaryls, and dienes, as well as a general mechanism for the selective transfer of ligands between two metal catalysts. We anticipate that this

  12. Ethidium bromide stimulated hyper laccase production from bird's nest fungus Cyathus bulleri.

    Science.gov (United States)

    Dhawan, S; Lal, R; Kuhad, R C

    2003-01-01

    Effect of ethidium bromide, a DNA intercalating agent, on laccase production from Cyathus bulleri was studied. The bird's nest fungus, Cyathus bulleri was grown on 2% (w/v) malt extract agar (MEA) supplemented with 1.5 microg ml(-1) of the phenanthridine dye ethidium bromide (EtBr) for 7 d and when grown subsequently in malt extract broth (MEB), produced a 4.2-fold increase in laccase production as compared to the untreated fungus. The fungal cultures following a single EtBr treatment, when regrown on MEA devoid of EtBr, produced a sixfold increase in laccase in MEB. However, on subsequent culturing on MEA in the absence of EtBr, only a 2.5-fold increase in laccase production could be maintained. In another attempt, the initial EtBr-treated cultures, when subjected to a second EtBr treatment (1.5 microg ml(-1)) on MEA for 7 d, produced a 1.4-fold increase in laccase production in MEB. The white-rot fungus Cyathus bulleri, when treated with EtBr at a concentration of 1.5 microg ml(-1) and regrown on MEA devoid of EtBr, produced a sixfold increase in laccase production in MEB. The variable form of C. bulleri capable of hyper laccase production can improve the economic feasibility of environmentally benign processes involving use of fungal laccases in cosmetics (including hair dyes), food and beverages, clinical diagnostics, pulp and paper industry, industrial effluent treatment, animal biotechnology and biotransformations.

  13. Single nucleotide polymorphism discrimination with and without an ethidium bromide intercalator

    International Nuclear Information System (INIS)

    Fenati, Renzo A.; Connolly, Ashley R.; Ellis, Amanda V.

    2017-01-01

    Single nucleotide polymorphism (SNP) genotyping is an important aspect in understanding genetic variations. Here, we discriminate SNPs using toe-hold mediated displacement reactions. The biological target is an 80 nucleotide long double-stranded–DNA from the mtDNA HV1 region, associated with maternal ancestry. This target has been specially designed with a pendant toehold and a cationic fluorophore, ATTO 647N, as a reporter, produced in a polymerase chain reaction. Rates of reaction for the toehold-polymerase chain reaction products (TPPs) with their corresponding complementary displacing sequences, labelled with a Black Hole Quencher 1, followed the order TPP–Cytosine > TPP–Thymine > TPP–Adenine ≥ TPP–Guanine. Non-complementary rates were the slowest with mismatches involving cytosine. These reactions, operating in a static/or contact mode, gave averaged readouts between SNPs within 15 min (with 80–90% quenching), compared to 25–30 min in previous studies involving fluorescence resonance energy transfer. Addition of an intercalating agent, ethidium bromide, retarded the rate of reaction in which cytosine was involved, presumably through stabilization of the base pairing, which resulted in markedly improved discrimination of cytosine containing SNPs. - Highlights: • Fluorophores and DNA intercalators effect the rate of toehold-mediated strand displacement. • Ethidium bromide had a destabilizing effect on mismatches that contained cytosine. • A cationic fluorophore and Black Hole Quencher 1 strand displacement system was 2–3 times faster than a FRET system. • This enabled SNP detection using toehold-mediated strand displacement in 15 min.

  14. Modeling bromide effects on yields and speciation of dihaloacetonitriles formed in chlorinated drinking water.

    Science.gov (United States)

    Roccaro, Paolo; Chang, Hyun-shik; Vagliasindi, Federico G A; Korshin, Gregory V

    2013-10-15

    This study examined effects of bromide on yields and speciation of dihaloacetonitrile (DHAN) species that included dichloro-, bromochloro- and dibromoacetonitriles generated in chlorinated water. Experimental data obtained using two water sources, varying concentrations and characters of Natural Organic Matter (NOM), bromide concentrations, reaction times, chlorine doses, temperatures and pHs were interpreted using a semi-phenomenological model that assumed the presence of three kinetically distinct sites in NOM (denoted as sites S1, S2 and S3) and the occurrence of sequential incorporation of bromine and chlorine into them. One site was found to react very fast with the chlorine and bromine but its contribution in the DHAN generation was very low. The site with the highest contribution to the yield of DHAN (>70%) has the lowest reaction rates. The model introduced dimensionless coefficients (denoted as φ1(DHAN), φ2(DHAN) and φ3(DHAN)) applicable to the initial DHAN generation sites and their monochlorinated and monobrominated products, respectively. These parameters were used to quantify the kinetic preference to bromine incorporation over that of chlorine. Values of these coefficients optimized for DHAN formation were indicative of the strongly preferential incorporation of bromine into the engaged NOM sites. The same set of φ(i)(DHAN) coefficients could be used to model the speciation of DHAN released from their kinetically different precursors. The dimensionless speciation coefficients φ(i)(DHAN) were determined to be site specific and dependent on the NOM content and character as well as pH. The presented model of DHAN formation and speciation can help quantify in more detail the generation of DHAN and provide more insight necessary for further assessment of their potential health effects. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. Role of once-daily glycopyrronium bromide (NVA237 in the management of COPD

    Directory of Open Access Journals (Sweden)

    D’Urzo A

    2013-08-01

    Full Text Available Anthony D'UrzoDepartment of Family and Community Medicine, University of Toronto, Toronto, ON, CanadaAbstract: Progressive airflow limitation is a hallmark feature of chronic obstructive pulmonary disease (COPD that ultimately leads to breathlessness, impaired quality of life, and reduced exercise capacity. Pharmacotherapy is used in patients with COPD to prevent and control symptoms, reduce both the frequency and severity of exacerbations, improve health status, and increase exercise tolerance. These strategies are intended to address management issues which promote both current disease control and a reduction in the risk of disease deterioration in the future. At the present time, long-acting β2-agonists (LABAs and long-acting muscarinic antagonists (LAMAs are available for maintenance therapy in patients with persistent symptoms. Tiotropium was the first LAMA to be approved for management of COPD, and many studies have described its beneficial effects on multiple clinically relevant outcomes. Glycopyrronium bromide (NVA237, a new LAMA, has been developed and received regulatory approval for management of COPD in a number of countries around the world. Results from pivotal Phase III trials suggest that NVA237 is safe and well tolerated in patients with moderate to severe COPD, and provides rapid and sustained improvements in lung function. Further, these changes are associated with statistically and clinically meaningful improvements in dyspnea, health-related quality of life, and exercise tolerance. Treatment with NVA237 also results in a significant reduction in risk of exacerbations and the need for rescue medication, and has been comparable with tiotropium with respect to safety and efficacy outcomes. Finally, emerging data indicate that NVA237 is efficacious both as monotherapy and in combination with indacaterol.Keywords: glycopyrronium bromide, NVA237, chronic obstructive pulmonary disease, inhaled long-acting bronchodilators

  16. Single nucleotide polymorphism discrimination with and without an ethidium bromide intercalator

    Energy Technology Data Exchange (ETDEWEB)

    Fenati, Renzo A.; Connolly, Ashley R. [Flinders Centre for Nanoscale Science and Technology, Flinders University, Sturt Road, Bedford Park, Adelaide, South Australia 5042 (Australia); Ellis, Amanda V., E-mail: amanda.ellis@flinders.edu.au [Flinders Centre for Nanoscale Science and Technology, Flinders University, Sturt Road, Bedford Park, Adelaide, South Australia 5042 (Australia); Chemical and Biomolecular Engineering, The University of Melbourne, Parkville, VIC 3010 (Australia)

    2017-02-15

    Single nucleotide polymorphism (SNP) genotyping is an important aspect in understanding genetic variations. Here, we discriminate SNPs using toe-hold mediated displacement reactions. The biological target is an 80 nucleotide long double-stranded–DNA from the mtDNA HV1 region, associated with maternal ancestry. This target has been specially designed with a pendant toehold and a cationic fluorophore, ATTO 647N, as a reporter, produced in a polymerase chain reaction. Rates of reaction for the toehold-polymerase chain reaction products (TPPs) with their corresponding complementary displacing sequences, labelled with a Black Hole Quencher 1, followed the order TPP–Cytosine > TPP–Thymine > TPP–Adenine ≥ TPP–Guanine. Non-complementary rates were the slowest with mismatches involving cytosine. These reactions, operating in a static/or contact mode, gave averaged readouts between SNPs within 15 min (with 80–90% quenching), compared to 25–30 min in previous studies involving fluorescence resonance energy transfer. Addition of an intercalating agent, ethidium bromide, retarded the rate of reaction in which cytosine was involved, presumably through stabilization of the base pairing, which resulted in markedly improved discrimination of cytosine containing SNPs. - Highlights: • Fluorophores and DNA intercalators effect the rate of toehold-mediated strand displacement. • Ethidium bromide had a destabilizing effect on mismatches that contained cytosine. • A cationic fluorophore and Black Hole Quencher 1 strand displacement system was 2–3 times faster than a FRET system. • This enabled SNP detection using toehold-mediated strand displacement in 15 min.

  17. Nanosized sustained-release pyridostigmine bromide microcapsules: process optimization and evaluation of characteristics

    Science.gov (United States)

    Tan, Qunyou; Jiang, Rong; Xu, Meiling; Liu, Guodong; Li, Songlin; Zhang, Jingqing

    2013-01-01

    Background Pyridostigmine bromide (3-[[(dimethylamino)-carbonyl]oxy]-1-methylpyridinium bromide), a reversible inhibitor of cholinesterase, is given orally in tablet form, and a treatment schedule of multiple daily doses is recommended for adult patients. Nanotechnology was used in this study to develop an alternative sustained-release delivery system for pyridostigmine, a synthetic drug with high solubility and poor oral bioavailability, hence a Class III drug according to the Biopharmaceutics Classification System. Novel nanosized pyridostigmine-poly(lactic acid) microcapsules (PPNMCs) were expected to have a longer duration of action than free pyridostigmine and previously reported sustained-release formulations of pyridostigmine. Methods The PPNMCs were prepared using a double emulsion-solvent evaporation method to achieve sustained-release characteristics for pyridostigmine. The preparation process for the PPNMCs was optimized by single-factor experiments. The size distribution, zeta potential, and sustained-release behavior were evaluated in different types of release medium. Results The optimal volume ratio of inner phase to external phase, poly(lactic acid) concentration, polyvinyl alcohol concentration, and amount of pyridostigmine were 1:10, 6%, 3% and 40 mg, respectively. The negatively charged PPNMCs had an average particle size of 937.9 nm. Compared with free pyridostigmine, PPNMCs showed an initial burst release and a subsequent very slow release in vitro. The release profiles for the PPNMCs in four different types of dissolution medium were fitted to the Ritger-Peppas and Weibull models. The similarity between pairs of dissolution profiles for the PPNMCs in different types of medium was statistically significant, and the difference between the release curves for PPNMCs and free pyridostigmine was also statistically significant. Conclusion PPNMCs prepared by the optimized protocol described here were in the nanometer range and had good uniformity

  18. 78 FR 14508 - Notice of Affirmation of Addition of a Treatment Schedule for Methyl Bromide Fumigation of...

    Science.gov (United States)

    2013-03-06

    ... contacting the Animal and Plant Health Inspection Service, Plant Protection and Quarantine, Manuals Unit, 92... the Plant Protection and Quarantine Treatment Manual a treatment schedule for methyl bromide..., 2013, we are affirming the addition to the Plant Protection and Quarantine Treatment Manual of the...

  19. FLUORESCENCE SPECTROSCOPIC STUDY OF THE FORMATION OF HYDROPHOBIC MICRODOMAINS IN AQUEOUS-SOLUTIONS OF POLY(ALKYLMETHYLDIALLYLAMMONIUM BROMIDES)

    NARCIS (Netherlands)

    YANG, YJ; Engberts, Jan B F N

    The conformational state of poly(alkylmethyldiallylammonium bromides) was studied in aqueous solutions using pyrene as a fluorescence probe. The results are indicative for the formation of hydrophobic microdomains in the case of several copolymers which possess sufficiently hydrophobic alkyl side

  20. FLUORESCENCE PROBING OF THE FORMATION OF HYDROPHOBIC MICRODOMAINS BY CROSS-LINKED POLY(ALKYLMETHYLDIALLYLAMMONIUM BROMIDES) IN AQUEOUS-SOLUTION

    NARCIS (Netherlands)

    WANG, GJ; ENGBERTS, J B F N

    Pyrene has been used as a fluorescence probe to investigate the conformational behavior of cross-linked poly(alkylmethyldiallylammonium bromides) in aqueous solutions. Binding of pyrene to hydrophobic microdomains, formed by the polysoaps, is reflected by a change in the ratio I-1/I-3 of the

  1. Measurement of properties of a lithium bromide aqueous solution for the determination of the concentration for a prototype absorption machine

    International Nuclear Information System (INIS)

    Labra, L.; Juárez-Romero, D.; Siqueiros, J.; Coronas, A.; Salavera, D.

    2017-01-01

    Highlights: • Determination of concentration of absorption mixture for absorption heat transformers. • Measurement of physical properties for heat transformer assessment. • Comparative behavior of Electric conductivity, Refractive index, and density of LiBr-H_2O. - Abstract: An electrolyte solution of Lithium Bromide (LiBr) water was chosen for study because of its wide use in prototype absorption machines. The LiBr must be operated close to the temperature and mass fraction at which lithium bromide achieves the highest efficiency. For the purpose of establishing the concentration in a prototype absorption machines, measurements were made of the properties that vary with temperature and concentration. The selected properties are electrical conductivity, density, refractive indexes and sound velocity. The resulting measured properties values were compared with some values found in previous works. The properties of aqueous lithium bromide solutions were measured at the concentration range of 45–65% of LiBr and temperatures range of 20–80 °C. Semi-empirical correlations that determine the properties of lithium bromide are also proposed. The methods for measuring the properties of aqueous solutions were considered taking into account their reliability, simplicity and sampling time.

  2. Suzuki coupling reactions catalyzed by poly(N-ethyl-4-vinylpyridinium bromide stabilized palladium nanoparticles in aqueous solution

    Directory of Open Access Journals (Sweden)

    2008-04-01

    Full Text Available InIn this work, it was investigated to use of poly(N-ethyl-4-vinylpyridinium bromide stabilized palladium nanoparticles in the Suzuki reaction between phenylboronic acid and aryl halides in aqueous solution. The nanoparticles were isolated and re-used several times with low loss of activity.

  3. Substituent Effects Dehalogenation of Aryl Bromides with NaAlH2(OCH2CH2OCH3)2

    Czech Academy of Sciences Publication Activity Database

    Czakoová, Marie; Hetflejš, Jiří; Včelák, Jaroslav

    2001-01-01

    Roč. 72, č. 2 (2001), s. 277-287 ISSN 0133-1736 R&D Projects: GA ČR GA203/97/1173 Institutional research plan: CEZ:AV0Z4072921 Keywords : substituent effects * aryl bromides * Co-assisted debromination Subject RIV: CC - Organic Chemistry Impact factor: 0.475, year: 2001

  4. Elimination of nonspecific radioactivity from [{sup 76}Br]bromide in PET study with [{sup 76}Br]bromodeoxyuridine

    Energy Technology Data Exchange (ETDEWEB)

    Li Lu; Bergstroem, Mats E-mail: Mats.Bergstroem@pet.uu.se; Fasth, Karl-Johan; Wu Feng; Eriksson, Barbro; Laangstroem, Bengt

    1999-10-01

    [{sup 76}Br]Bromodeoxyuridine ([{sup 76}Br]BrdU) might allow a determination of proliferation in vivo using positron emission tomography (PET), but only with consideration of organ nonspecific radioactivity constituted by [{sup 76}Br]bromide. A first study assessed the potential of diuretics to eliminate [{sup 76}Br]bromide. [{sup 76}Br]Bromide was injected in the vein of rats and different diuretic combinations were given. Urine was collected and radioactivity measured. Torasemide plus sodium chloride gave better {sup 76}Br elimination than the other diuretics. In a second experiment, rats were given [{sup 76}Br]BrdU. After the radioactivity injection, the rats of the treatment group were given torasemide plus NaCl. At 44 h after the radioactivity injection, the radioactivity concentration and the fraction incorporated into DNA were measured in different organs. Using diuretics, the elimination of [{sup 76}Br]bromide was increased. The radioactivity decreased 30-50% in most of the organs but the highest radioactivity uptake was found in the organs with more active DNA synthesis. This method may facilitate the use of [{sup 76}Br]BrdU as a tracer for DNA synthesis using PET.

  5. Elimination of nonspecific radioactivity from [76Br]bromide in PET study with [76Br]bromodeoxyuridine

    International Nuclear Information System (INIS)

    Li Lu; Bergstroem, Mats; Fasth, Karl-Johan; Wu Feng; Eriksson, Barbro; Laangstroem, Bengt

    1999-01-01

    [ 76 Br]Bromodeoxyuridine ([ 76 Br]BrdU) might allow a determination of proliferation in vivo using positron emission tomography (PET), but only with consideration of organ nonspecific radioactivity constituted by [ 76 Br]bromide. A first study assessed the potential of diuretics to eliminate [ 76 Br]bromide. [ 76 Br]Bromide was injected in the vein of rats and different diuretic combinations were given. Urine was collected and radioactivity measured. Torasemide plus sodium chloride gave better 76 Br elimination than the other diuretics. In a second experiment, rats were given [ 76 Br]BrdU. After the radioactivity injection, the rats of the treatment group were given torasemide plus NaCl. At 44 h after the radioactivity injection, the radioactivity concentration and the fraction incorporated into DNA were measured in different organs. Using diuretics, the elimination of [ 76 Br]bromide was increased. The radioactivity decreased 30-50% in most of the organs but the highest radioactivity uptake was found in the organs with more active DNA synthesis. This method may facilitate the use of [ 76 Br]BrdU as a tracer for DNA synthesis using PET

  6. Visible light-photocatalysed carbazole synthesis via a formal (4+2) cycloaddition of indole-derived bromides and alkynes.

    Science.gov (United States)

    Yuan, Zhi-Guang; Wang, Qiang; Zheng, Ang; Zhang, Kai; Lu, Liang-Qiu; Tang, Zilong; Xiao, Wen-Jing

    2016-04-14

    We successfully developed an unprecedented route to carbazole synthesis through a visible light-photocatalysed formal (4+2) cycloaddition of indole-derived bromides and alkynes. This novel protocol features extremely mild conditions, a broad substrate scope and high reaction efficiency.

  7. Biological half-life of bromide in the rat depends primarily on the magnitude of sodium intake

    Czech Academy of Sciences Publication Activity Database

    Pavelka, Stanislav; Babický, Arnošt; Vobecký, Miloslav

    2005-01-01

    Roč. 54, č. 6 (2005), s. 639-644 ISSN 0862-8408 Institutional research plan: CEZ:AV0Z50110509 Keywords : biological half-life * bromide * sodium Subject RIV: ED - Physiology Impact factor: 1.806, year: 2005

  8. Analysis of genotoxic activity of ketamine and rocuronium bromide using the somatic mutation and recombination test in Drosophila melanogaster.

    Science.gov (United States)

    Koksal, Pakize Muge; Gürbüzel, Mehmet

    2015-03-01

    The present study evaluated the mutagenic and recombinogenic effects of two commonly used anesthetic agents, ketamine and rocuronium bromide, in medicine using the wing somatic mutation and recombination test (SMART) in Drosophila. The standard (ST) cross and the high-bioactivation (HB) cross with high sensitivity to procarcinogens and promutagens were used. The SMART test is based on the loss of heterozygosity, which occurs via various mechanisms, such as chromosome loss and deletion, half-translocation, mitotic recombination, mutation, and non-disjunction. Genetic alterations occurring in the somatic cells of the wing's imaginal discs result in mutant clones in the wing blade. Three-day-old trans-heterozygous larvae with two recessive markers, multiple wing hairs (mwh) and flare (flr(3)), were treated with ketamine and rocuronium bromide. Analysis of the ST cross indicated that ketamine exhibited genotoxicity activity and that this activity was particularly dependent on homologous mitotic recombination at concentrations of 250 μg/ml and above. Rocuronium bromide did not exert mutagenic and/or recombinogenic effects. In the HB cross, ketamine at a concentration of 1000 μg/ml and rocuronium bromide at all concentrations, with the exception of 250 μg/ml (inconclusive), exerted genotoxic effects, which could also be associated with the increase in mitotic recombination. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. tBuLi-Mediated One-Pot Direct Highly Selective Cross-Coupling of Two Distinct Aryl Bromides

    NARCIS (Netherlands)

    Vila, Carlos; Cembellin, Sara; Hornillos, Valentin; Giannerini, Massimo; Fananas-Mastral, Martin; Feringa, Ben L.

    2015-01-01

    A Pd-catalyzed direct cross-coupling of two distinct aryl bromides mediated by tBuLi is described. The use of [Pd-PEPPSI-IPr] or [Pd-PEPPSI-IPent] as catalyst allows for the efficient one-pot synthesis of unsymmetrical biaryls at room temperature. The key for this selective cross-coupling is the use

  10. Bromide as a tracer for studying water movement and nitrate displacement in soils: comparison with stable isotope tracers

    International Nuclear Information System (INIS)

    Russow, R.; Knappe, S.

    1999-01-01

    Tracers are an ideal means of studying water movement and associated nitrate displacement. Often bromide is preferred as a tracer because it is considered a representative tracer for water and because, being a conservative tracer (i.e. not involved in chemical and biological soil processes), it can be used for studying anion transport in soils. Moreover, it is less expensive and easier to measure than the stable isotopes deuterium and 15 N. Its great advantage over radioactive tracers (e.g. tritium), which outweighs their extreme sensitivity and ease of measurement and which it has in common with stable isotopes, is that it does not require radiation protection measures. However, there are also constraints on the use of bromide as a tracer in soil/water/plant systems. Our own studies on different soils using D 2 O, bromide and [ 15 N]-nitrate in lysimeters suggest that the above assumptions on bromide tracers need not always be valid under conditions as they prevail in biologically active soils. As the present paper shows, these studies permit a good assessment of the possibilities and limits to these tracers [de

  11. The vapour pressures over saturated aqueous solutions of cadmium chloride, cadmium bromide, cadmium iodide, cadmium nitrate, and cadmium sulphate

    International Nuclear Information System (INIS)

    Apelblat, Alexander; Korin, Eli

    2007-01-01

    Vapour pressures of water over saturated solutions of cadmium salts (chloride, bromide, iodide, nitrate, and sulphate) were determined over the temperature range 280 K to 322 K and compared with the literature data. The vapour pressures determined were used to obtain the water activities, osmotic coefficients and the molar enthalpies of vaporization in the (cadmium salt + water) systems

  12. The vapour pressures over saturated aqueous solutions of cadmium chloride, cadmium bromide, cadmium iodide, cadmium nitrate, and cadmium sulphate

    Energy Technology Data Exchange (ETDEWEB)

    Apelblat, Alexander [Department of Chemical Engineering, Ben Gurion University of the Negev, P.O. Box 653, Beer Sheva 84105 (Israel)]. E-mail: apelblat@bgu.ac.il; Korin, Eli [Department of Chemical Engineering, Ben Gurion University of the Negev, P.O. Box 653, Beer Sheva 84105 (Israel)

    2007-07-15

    Vapour pressures of water over saturated solutions of cadmium salts (chloride, bromide, iodide, nitrate, and sulphate) were determined over the temperature range 280 K to 322 K and compared with the literature data. The vapour pressures determined were used to obtain the water activities, osmotic coefficients and the molar enthalpies of vaporization in the (cadmium salt + water) systems.

  13. Optimal Liquidation under Stochastic Liquidity

    OpenAIRE

    Becherer, Dirk; Bilarev, Todor; Frentrup, Peter

    2016-01-01

    We solve explicitly a two-dimensional singular control problem of finite fuel type for infinite time horizon. The problem stems from the optimal liquidation of an asset position in a financial market with multiplicative and transient price impact. Liquidity is stochastic in that the volume effect process, which determines the inter-temporal resilience of the market in spirit of Predoiu, Shaikhet and Shreve (2011), is taken to be stochastic, being driven by own random noise. The optimal contro...

  14. Hexadecyltrimethylammonium bromide (CTA-Br) and 1-butyl-3-methylimidazolium tetrafluoroborate (bmim-BF4) in aqueous solution: An ephemeral binary system.

    Science.gov (United States)

    Comelles, Francesc; Ribosa, Isabel; Gonzalez, Juan José; Garcia, M Teresa

    2017-03-15

    Mixtures of the cationic surfactant hexadecyltrimethylammonium bromide (CTA-Br) and the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate (bmim-BF 4 ) in aqueous solutions are expected to behave as typical binary cationic surfactant system taking into account the surface activity displayed by the ionic liquid, instead of considering the IL as a water cosolvent. Surface tension and conductivity measurements have been conducted as a function of the total concentration of the mixtures at different surfactant mole fraction (α CTA-Br ) to investigate the surface active properties. Turbidity immediately appearing when the compounds are mixed in water suggests the spontaneous formation of the low soluble compound hexadecyltrimethylammonium tetrafluoroborate (CTA-BF 4 ), together with the salt formed by the respective counterions bmim + and Br - in solution. For α CTA-Br ≠0.5, furthermore of the mentioned compounds, the spare bmim-BF 4 (for α CTA-Br Br (for α CTA-Br >0.5), are also present in the aqueous solution. Systems containing excess of bmim-BF 4 show a low critical aggregate concentration (cac), but an unexpected high surface tension at cac (γ cac ≈53-56mN/m), as pure CTA-BF 4 . For systems containing excess of CTA-Br, cac increases but γ cac decreases up to 36mN/m. Mixtures of pure CTA-BF 4 and bmim-BF 4 or CTA-Br behave as typical binary surfactant systems. Copyright © 2016 Elsevier Inc. All rights reserved.

  15. Effect of preconditioning on silver leaching and bromide removal properties of silver-impregnated activated carbon (SIAC).

    Science.gov (United States)

    Rajaeian, Babak; Allard, Sébastien; Joll, Cynthia; Heitz, Anna

    2018-07-01

    Silver impregnated activated carbon (SIAC) has been found to be effective in mitigating the formation of brominated-disinfection by products during drinking water treatment. However, there are still uncertainties regarding its silver leaching properties, and strategies for the prevention of silver leaching have remained elusive. This study focused on the evaluation of one type of commercially available SIAC for its ability to remove bromide while minimising silver leaching from the material. Both synthetic and real water matrices were tested. Depending on solution pH, it was found that changing the surface charge properties of SIAC, as measured by the point of zero charge pH, can result in additional bromide removal while minimising the extent of silver leaching. To better understand the mechanism of silver leaching from the SIAC, eight preconditioning environments, i.e. variable pH and ionic strength were tested for a fixed amount of SIAC and two preconditioning environments were selected for a more detailed investigation. Experiments carried out in synthetic water showed that preconditioning at pH 10.4 did not deteriorate the capacity of SIAC to remove bromide, but significantly decreased the release of silver in the form of ionic silver (Ag + ), silver bromide (AgBr) and silver chloride (AgCl) from 40% for the pristine to 3% for the treated SIAC. This was confirmed using a groundwater sample. These results suggest that preconditioned SIAC has the potential to be an effective method for bromide removal with minimised silver leaching in a long-term field application for drinking water production. Copyright © 2018 Elsevier Ltd. All rights reserved.

  16. Impact of bromide on halogen incorporation into organic moieties in chlorinated drinking water treatment and distribution systems.

    Science.gov (United States)

    Tan, J; Allard, S; Gruchlik, Y; McDonald, S; Joll, C A; Heitz, A

    2016-01-15

    The impact of elevated bromide concentrations (399 to 750 μg/L) on the formation of halogenated disinfection by-products (DBPs), namely trihalomethanes, haloacetic acids, haloacetonitriles, and adsorbable organic halogen (AOX), in two drinking water systems was investigated. Bromine was the main halogen incorporated into all of the DBP classes and into organic carbon, even though chlorine was present in large excess to maintain a disinfectant residual. Due to the higher reactivity of bromine compared to chlorine, brominated DBPs were rapidly formed, followed by a slower increase in chlorinated DBPs. Higher bromine substitution and incorporation factors for individual DBP classes were observed for the chlorinated water from the groundwater source (lower concentration of dissolved organic carbon (DOC)), which contained a higher concentration of bromide, than for the surface water source (higher DOC). The molar distribution of adsorbable organic bromine to chlorine (AOBr/AOCl) for AOX in the groundwater distribution system was 1.5:1 and almost 1:1 for the surface water system. The measured (regulated) DBPs only accounted for 16 to 33% of the total organic halogen, demonstrating that AOX measurements are essential to provide a full understanding of the formation of halogenated DBPs in drinking waters. In addition, the study demonstrated that a significant proportion (up to 94%) of the bromide in source waters can be converted AOBr. An evaluation of AOBr and AOCl through a second groundwater treatment plant that uses conventional treatment processes for DOC removal produced 70% of AOX as AOBr, with 69% of the initial source water bromide converted to AOBr. Exposure to organobromine compounds is suspected to result in greater adverse health consequences than their chlorinated analogues. Therefore, this study highlights the need for improved methods to selectively reduce the bromide content in source waters. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Liquidity risk and contagion for liquid funds

    OpenAIRE

    Darolles , Serge; Dudek , Jeremy; Le Fol , Gaëlle

    2014-01-01

    Fund managers face liquidity problems but they have to distinguish the market liquidity risk implied by their assets and the funding liquidity risk. This latter is due to both the liquidity mismatch between assets and liabilities and the redemption risk due to the possible outflows from clients. The main contribution of this paper is the analysis of contagion looking at common market liquidity problems to detect funding liquidity problems. Using the CDS Bond Spread basis as a liquidity indica...

  18. Hidden Liquidity

    OpenAIRE

    Cebiroglu, Gökhan; Horst, Ulrich

    2012-01-01

    We cross-sectionally analyze the presence of aggregated hidden depth and trade volume in the S&P 500 and identify its key determinants. We find that the spread is the main predictor for a stock’s hidden dimension, both in terms of traded and posted liquidity. Our findings moreover suggest that large hidden orders are associated with larger transaction costs, higher price impact and increased volatility. In particular, as large hidden orders fail to attract (latent) liquidity to the market, hi...

  19. CdTe quantum dots functionalized with 4-amino-2,2,6,6-tetramethylpiperidine-N-oxide as luminescent nanoprobe for the sensitive recognition of bromide ion

    International Nuclear Information System (INIS)

    Adegoke, Oluwasesan; Hosten, Eric; McCleland, Cedric; Nyokong, Tebello

    2012-01-01

    Graphical abstract: A bromide ion-selective modified nanoprobe sensor based on 4-amino-2,2,6,6-tetramethylpiperidine-N-oxide (4AT)-functionalized CdTe quantum dots (QDs-4AT) showed a high selectivity and sensitivity for the determination of bromide ion using fluorescence recovery. Highlights: ► Water soluble CdTe quantum dots interact with tetramethylpiperidine-N-oxide. ► Quantum dots fluorescence is quenched by the radical. ► In the presence of bromide ions the fluorescence is restored. ► The sensor is more selective to bromine ions than other common ions. - Abstract: A novel bromide ion-selective modified nanoprobe sensor based on 4-amino-2,2,6,6-tetramethylpiperidine-N-oxide (4AT)-functionalized CdTe quantum dots (QDs-4AT) has been developed. Fluorescence quenching of the QDs by 4AT was observed. The functionalized QDs-4AT nanoprobe allowed a highly sensitive determination of bromide ion via analyte-induced change in the photoluminescence (fluorescence recovery) of the modified QDs. A detection limit of 0.6 nM of bromide ion was obtained, while the interfering effect of other inorganic cations and anions was investigated to examine the selectivity of the nanoprobe. The linear range was between 0.01 and 0.13 μM. Combined fluorescence lifetime and electron paramagnetic resonance measurements confirmed electron transfer processes between bromide ion and QDs-4AT.

  20. Liquid ventilation.

    Science.gov (United States)

    Sarkar, Suman; Paswan, Anil; Prakas, S

    2014-01-01

    Human have lungs to breathe air and they have no gills to breath liquids like fish. When the surface tension at the air-liquid interface of the lung increases as in acute lung injury, scientists started to think about filling the lung with fluid instead of air to reduce the surface tension and facilitate ventilation. Liquid ventilation (LV) is a technique of mechanical ventilation in which the lungs are insufflated with an oxygenated perfluorochemical liquid rather than an oxygen-containing gas mixture. The use of perfluorochemicals, rather than nitrogen as the inert carrier of oxygen and carbon dioxide offers a number of advantages for the treatment of acute lung injury. In addition, there are non-respiratory applications with expanding potential including pulmonary drug delivery and radiographic imaging. It is well-known that respiratory diseases are one of the most common causes of morbidity and mortality in intensive care unit. During the past few years several new modalities of treatment have been introduced. One of them and probably the most fascinating, is of LV. Partial LV, on which much of the existing research has concentrated, requires partial filling of lungs with perfluorocarbons (PFC's) and ventilation with gas tidal volumes using conventional mechanical ventilators. Various physico-chemical properties of PFC's make them the ideal media. It results in a dramatic improvement in lung compliance and oxygenation and decline in mean airway pressure and oxygen requirements. No long-term side-effect reported.

  1. Liquid Marbles

    KAUST Repository

    Khalil, Kareem

    2012-12-01

    Granulation, the process of formation of granules from a combination of base powders and binder liquids, has been a subject of research for almost 50 years, studied extensively for its vast applications, primarily to the pharmaceutical industry sector. The principal aim of granulation is to form granules comprised of the active pharmaceutical ingredients (API’s), which have more desirable handling and flowability properties than raw powders. It is also essential to ensure an even distribution of active ingredients within a tablet with the goal of achieving time‐controlled release of drugs. Due to the product‐specific nature of the industry, however, data is largely empirical [1]. For example, the raw powders used can vary in size by two orders of magnitude with narrow or broad size distributions. The physical properties of the binder liquids can also vary significantly depending on the powder properties and required granule size. Some significant progress has been made to better our understanding of the overall granulation process [1] and it is widely accepted that the initial nucleation / wetting stage, when the binder liquid first wets the powders, is key to the whole process. As such, many experimental studies have been conducted in attempt to elucidate the physics of this first stage [1], with two main mechanisms being observed – classified by Ivenson [1] as the “Traditional description” and the “Modern Approach”. See Figure 1 for a graphical definition of these two mechanisms. Recent studies have focused on the latter approach [1] and a new, exciting development in this field is the Liquid Marble. This interesting formation occurs when a liquid droplet interacts with a hydrophobic (or superhydrophobic) powder. The droplet can become encased in the powder, which essentially provides a protective “shell” or “jacket” for the liquid inside [2]. The liquid inside is then isolated from contact with other solids or liquids and has some

  2. Persistent modification of Nav1.9 following chronic exposure to insecticides and pyridostigmine bromide

    International Nuclear Information System (INIS)

    Nutter, Thomas J.; Cooper, Brian Y.

    2014-01-01

    Many veterans of the 1991 Gulf War (GW) returned from that conflict with a widespread chronic pain affecting deep tissues. Recently, we have shown that a 60 day exposure to the insecticides permethrin, chlorpyrifos, and pyridostigmine bromide (NTPB) had little influence on nociceptor action potential forming Na v 1.8, but increased K v 7 mediated inhibitory currents 8 weeks after treatment. Using the same exposure regimen, we used whole cell patch methods to examine whether the influences of NTPB could be observed on Na v 1.9 expressed in muscle and vascular nociceptors. During a 60 day exposure to NTPB, rats exhibited lowered muscle pain thresholds and increased rest periods, but these measures subsequently returned to normal levels. Eight and 12 weeks after treatments ceased, DRG neurons were excised from the sensory ganglia. Whole cell patch studies revealed little change in voltage dependent activation and deactivation of Na v 1.9, but significant increases in the amplitude of Na v 1.9 were observed 8 weeks after exposure. Cellular studies, at the 8 week delay, revealed that NTPB also significantly prolonged action potential duration and afterhyperpolarization (22 °C). Acute application of permethrin (10 μM) also increased the amplitude of Na v 1.9 in skin, muscle and vascular nociceptors. In conclusion, chronic exposure to Gulf War agents produced long term changes in the amplitude of Na v 1.9 expressed in muscle and vascular nociceptors. The reported increases in K v 7 amplitude may have been an adaptive response to increased Na v 1.9, and effectively suppressed behavioral pain measures in the post treatment period. Factors that alter the balance between Na v 1.9 and K v 7 could release spontaneous discharge and produce chronic deep tissue pain. - Highlights: • Rats were treated 60 days with permethrin, chlorpyrifos and pyridostigmine bromide. • 8 weeks after treatments, Nav1.9 activation and deactivation were unchanged. • The amplitude and

  3. Simultaneous determination of bromide and iodide as acetone derivatives by gas chromatography and electron capture detection in natural waters and biological fluids

    International Nuclear Information System (INIS)

    Maros, L.; Kaldy, M.; Igaz, S.

    1989-01-01

    Oxidation of bromide and iodide ions in acidic solutions in the presence of acetone forms the corresponding acetone derivatives. Iodate was reduced with thiosulfate prior to the determination. After extraction with benzene the bromo- and iodoacetone were measured by gas chromatography using electron capture detection. The bromide and iodide contents of rainwater, drinking water, river water, seawater, oil brine, common salt, cow milk, and human blood serum were determined. The relative standard deviations for bromide at 10/sup /minus/7/ M and for iodide at 10/sup /minus/8/ M concentration were 1.9% and 3.0%, respectively, using 10-mL sample for the determination without preconcentration

  4. Characterization of the influence of 1-butyl-3-methylimidazolium chloride on the structure and thermal stability of green fluorescent protein

    International Nuclear Information System (INIS)

    Heller, William T.; O'Neill, Hugh Michael; Zhang, Qiu; Baker, Gary A.

    2010-01-01

    Ionic liquids (ILs) are finding a vast array of applications as novel solvents for a wide variety of processes that include enzymatic chemistry, particularly as more biocompatible ILs are designed and discovered. While it is assumed that a native or near-native structure is required for enzymatic activity, there is some evidence that ILs alter protein structure and oligomerization states in a manner than can negatively impact function. The IL 1-butyl-3-methylimidazolium chloride, (bmim)Cl, is a well-studied, water-miscible member of the popular 1-alkyl-3-methylimidazolium IL family. To improve our understanding of the impact of water-miscible ILs on proteins, we have characterized the structure and oligomerization state of green fluorescent protein (GFP) in aqueous solutions containing 25 and 50 vol % (bmim)Cl using a combination of optical spectroscopy and small-angle neutron scattering (SANS). Measurements were also performed as a function of temperature to provide insight into the effect of the IL on the thermal stability of GFP. While GFP exists as a dimer in water, the presence of 25 vol % (bmim)Cl causes GFP to transition to a monomeric state. The SANS data indicate that GFP is a great deal less compact in 50 vol % (bmim)Cl than in neat water, indicative of unfolding from the native structure. The oligomerization state of the protein in IL-containing aqueous solution changes from a dimer to a monomer in response to the IL, but does not change as a function of temperature in the IL-containing solution. The SANS and spectroscopic results also demonstrate that the addition of (bmim)Cl to the solution decreases the thermal stability of GFP, allowing the protein to unfold at lower temperatures than in aqueous solution.

  5. Liposomes containing cationic dimethyl dioctadecyl ammonium bromide: formulation, quality control, and lipofection efficiency.

    Science.gov (United States)

    Dass, Crispin R; Walker, Todd L; Burton, Mark A

    2002-01-01

    This article describes a novel, simple, and relatively inexpensive method to prepare cationic liposomes using an ethanol injection/pressure extrusion method. The study also demonstrated that binding erythrosine dye to cationic liposomes results in a shift of the absorption maximum of the dye from 528 nm to 549 nm at pH 4.25, allowing quantification and visualization of these vesicles. In addition, a relatively simple Ficoll-based gradient centrifugation method for separation of lipoplexes from unbound molecules is presented. Laboratory-formulated dimethyl dioctadecyl ammonium bromide (DDAB) containing liposomes were just as efficient in complexing nucleic acids as commercially available types, and binding increased as the positive to neutral lipid ratio was increased. Transfection efficiency of the DDAB-containing liposomes increased as the ratio of cationic to neutral lipid was increased from 1:1 to 4:1 with either PtdChol or DOPE as the neutral lipid. A concomitant increase in cytotoxicity of CSU-SA1 cancer cells was noted as the ratio of positive to neutral lipid of the liposomes was increased. Nevertheless, our present study showed that the 2:1 liposome is a good choice since it delivers functional plasmids at a comparable rate to commercial liposome formulations, has similar toxicities to the less harmful commercial liposomes, and is at least 1000-fold more economical to prepare inhouse, a major factor to be considered in preclinical and clinical studies with these carriers.

  6. Modification of carbon nanotube's dispersion using cetyltrimethyl ammonium bromide (CTAB) as cancer drug delivery

    Science.gov (United States)

    Wulan, Praswati PDK.; Wulandari, Hanifia; Ulwan, Sekar H.; Purwanto, Widodo W.; Mulia, Kamarza

    2018-02-01

    Cancer is a disease that causes many deaths globally. Cancer treatments have side effects that can danger the human body. Carbon nanotube (CNT) becomes drug (anti-cancer) delivery towards cancer cells that have been targeted. Yet, CNT tends to aggregate. It could be overcome by functionalization (modification) of CNT using Cetyltrimethyl Ammonium Bromide (CTAB). The variations we use were CNT-CTAB with a dose of CNT 100 mg and CTAB varied between 80, 90, 100, 110, and 120 mg. There were several stages of CNT modification process: dispersion, filtration, washing, and drying. The optimum condition obtained was on CNT-110 mg CTAB because it could be dispersed up to 70 hours better than pure CNT, Zeta Potential (ZP) ≥16 mV, and absorbance Uv-vis 1.05. Both the ZP value and the absorbance of Uv-vis showed the CNT dispersion modified to be better than the pure CNT. Furthermore, SEM-EDX did not produce structural damage to CNT modified surfaces, the percentage of the mass of Oxygen (O) elements as characteristic of increased hydrophilic properties, and Ni elements as toxic impurities become reduced. FTIR spectrum results showed the highest intensity occurred at CTAB CNT-110mg at 1221 m-1. This strong C-N vibration interaction suggests that CNTs CNT modification become readily dispersed in water.

  7. A microcalorimetry and binding study on interaction of dodecyl trimethylammonium bromide with wigeon hemoglobin

    International Nuclear Information System (INIS)

    Bordbar, A.K.; Moosavi-Movahedi, A.A.; Amini, M.K.

    2003-01-01

    The thermodynamic parameters for the binding of dodecyl trimethylammonium bromide (DTAB) with wigeon hemoglobin (Hb) in aqueous solution at various pH and 27 deg. C have been measured by equilibrium dialysis and titration microcalorimetry techniques. The Scatchard plots represent unusual features at neutral and alkaline pH and specific binding at acidic pH. This leads us to analyze the binding data by fitting the data to the Hill equation for multiclasses of binding sites. The best fit was obtained with the equation for one class at acidic pH and two classes at neutral and alkaline pH. The thermodynamic analysis of the binding process shows that the strength of binding at neutral pH is more than these at other pH values. This can be related to the more accessible hydrophobic surface area of wigeon hemoglobin at this pH. The endothermic enthalpy data which was measured by microcalorimetry confirms the binding data analysis and represents the more regular and stable structure of wigeon hemoglobin at neutral pH

  8. Insights into the energetics and mechanism underlying the interaction of tetraethylammonium bromide with proteins

    International Nuclear Information System (INIS)

    Banerjee, Tuhina; Kishore, Nand

    2008-01-01

    Calorimetry has been employed to investigate the quantitative energetic aspects and mechanism underlying protein-tetraethylammonium bromide (TEAB) interactions. Differential scanning calorimetry and UV-Visible spectroscopy have been used to study the thermal unfolding of three proteins of different structure and function (bovine serum albumin, α-lactalbumin, and bovine pancreatic ribonuclease A). The mode of interaction has been studied by using isothermal titration calorimetry, which demonstrates the absence of appreciable specific binding of TEAB to the protein. This suggests the involvement of solvent mediated effects and, possibly weak non-specific binding. The thermal unfolding transitions were found to be calorimetrically reversible for α-lactalbumin and bovine pancreatic ribonuclease A and partially reversible in the case of bovine serum albumin. The results indicate protein destabilization promoted by the TEAB interaction. The preferential interaction parameters of TEAB with α-lactalbumin and ribonuclease A confirm that an increased interaction of the hydrophobic groups of the TEAB with that of the protein upon denaturation is responsible for the reduced thermal stability of the protein. The decrease in the thermal stability of proteins in the presence of TEAB is well supported by a red shift in the intrinsic fluorescence of these proteins leading to conformational change thereby shifting the native ↔ denatured equilibrium towards right. The forces responsible for the thermal denaturation of the proteins of different structure and function in the presence of TEAB are discussed

  9. Oxidative precipitation of ruthenium oxide for supercapacitors: Enhanced capacitive performances by adding cetyltrimethylammonium bromide

    Science.gov (United States)

    Chen, I.-Li; Wei, Yu-Chen; Chen, Tsan-Yao; Hu, Chi-Chang; Lin, Tsang-Lang

    2014-12-01

    Thermally stable and porous RuO2·xH2O with superior rate-retention capability is prepared by the H2O2-oxidative precipitation method modified with the cetyltrimethylammonium bromide (CTAB) template. The specific capacitance and rate-retention of RuO2·xH2O are considerably enhanced by the CTAB modification and annealing at 200 °C because of extremely localized crystallization and pore opening of slightly sintered RuO2·xH2O nanoparticles trapped with CTAB. This unique structure, confirmed by the X-ray absorption spectroscopic (XAS), Raman spectroscopic, and transmission electron microscopic (TEM) analyses, favors the utilization of RuO2·xH2O nanocrystals and increases the electrolyte accessibility in comparing with RuO2·xH2O without CTAB modification. The preferential orientation growth along the {101} facet of RuO2 nanocrystals in some local regions is acquired by the CTAB modification and annealing in air at temperatures ≥350 °C. Such preferential orientation growth of RuO2 crystallites is attributable to the oxidation of trapped surfactants during the thermal annealing process, which adsorb on the high surface energy planes of RuO2.

  10. Simulation of solar lithium bromide-water absorption cooling system with parabolic trough collector

    International Nuclear Information System (INIS)

    Mazloumi, M.; Naghashzadegan, M.; Javaherdeh, K.

    2008-01-01

    Ahwaz is one of the sweltering cities in Iran where an enormous amount of energy is being consumed to cool residential places in a year. The aim of this research is to simulate a solar single effect lithium bromide-water absorption cooling system in Ahwaz. The solar energy is absorbed by a horizontal N-S parabolic trough collector and stored in an insulated thermal storage tank. The system has been designed to supply the cooling load of a typical house where the cooling load peak is about 17.5 kW (5 tons of refrigeration), which occurs in July. A thermodynamic model has been used to simulate the absorption cycle. The working fluid is water, which is pumped directly to the collector. The results showed that the collector mass flow rate has a negligible effect on the minimum required collector area, but it has a significant effect on the optimum capacity of the storage tank. The minimum required collector area was about 57.6 m 2 , which could supply the cooling loads for the sunshine hours of the design day for July. The operation of the system has also been considered after sunset by saving solar energy

  11. Second law-based thermodynamic analysis of water-lithium bromide absorption refrigeration system

    Energy Technology Data Exchange (ETDEWEB)

    Kilic, Muhsin [Department of Mechanical Engineering, Faculty of Engineering and Architecture, Uludag University, TR 16059, Bursa (Turkey)]. E-mail: mkilic@uludag.edu.tr; Kaynakli, Omer [Department of Mechanical Engineering, Faculty of Engineering and Architecture, Uludag University, TR 16059, Bursa (Turkey)

    2007-08-15

    In this study, the first and the second law of thermodynamics are used to analyze the performance of a single-stage water-lithium bromide absorption refrigeration system (ARS) when some working parameters are varied. A mathematical model based on the exergy method is introduced to evaluate the system performance, exergy loss of each component and total exergy loss of all the system components. Parameters connected with performance of the cycle-circulation ratio (CR), coefficient of performance (COP), Carnot coefficient of performance (COP{sub c} ), exergetic efficiency ({xi}) and efficiency ratio ({tau})-are calculated from the thermodynamic properties of the working fluids at various operating conditions. Using the developed model, the effect of main system temperatures on the performance parameters of the system, irreversibilities in the thermal process and non-dimensional exergy loss of each component are analyzed in detail. The results show that the performance of the ARS increases with increasing generator and evaporator temperatures, but decreases with increasing condenser and absorber temperatures. Exergy losses in the expansion valves, pump and heat exchangers, especially refrigerant heat exchanger, are small compared to other components. The highest exergy loss occurs in the generator regardless of operating conditions, which therefore makes the generator the most important component of the cycle.

  12. Second law-based thermodynamic analysis of water-lithium bromide absorption refrigeration system

    International Nuclear Information System (INIS)

    Kilic, Muhsin; Kaynakli, Omer

    2007-01-01

    In this study, the first and the second law of thermodynamics are used to analyze the performance of a single-stage water-lithium bromide absorption refrigeration system (ARS) when some working parameters are varied. A mathematical model based on the exergy method is introduced to evaluate the system performance, exergy loss of each component and total exergy loss of all the system components. Parameters connected with performance of the cycle-circulation ratio (CR), coefficient of performance (COP), Carnot coefficient of performance (COP c ), exergetic efficiency (ξ) and efficiency ratio (τ)-are calculated from the thermodynamic properties of the working fluids at various operating conditions. Using the developed model, the effect of main system temperatures on the performance parameters of the system, irreversibilities in the thermal process and non-dimensional exergy loss of each component are analyzed in detail. The results show that the performance of the ARS increases with increasing generator and evaporator temperatures, but decreases with increasing condenser and absorber temperatures. Exergy losses in the expansion valves, pump and heat exchangers, especially refrigerant heat exchanger, are small compared to other components. The highest exergy loss occurs in the generator regardless of operating conditions, which therefore makes the generator the most important component of the cycle

  13. An investigation of the atmospheric sources and sinks of methyl bromide

    International Nuclear Information System (INIS)

    Singh, H.B.; Kanakidou, M.

    1993-01-01

    Methyl Bromide (CH 3 Br) is a ubiquitous component of the atmosphere and has been implicated as an important player in the depletion of stratospheric ozone. Atmospheric CH 3 Br abundances, interhemispheric gradients, oceanic concentrations, man-made emissions, and removal processes have been analyzed and interpreted with the help of a simple box model and a 2-D global photochemical model. Its calculated atmospheric lifetime (T) of 1.7-1.9 years, based on reaction with OH radicals, is consistent with a global source of 90-110 Gg (10 9 g)/year. Consequences of a much shorter lifetime of 1.2 years, due to possible deposition/hydrolysis losses, are also considered. Available data are used to estimate a CH 3 Br source that is 35% (20-50%) man-made and 65% (80-50%) natural. Oceans are substantially supersaturated and provide the most important natural source of ∼60 (40-80) Gg/year. Within the oceans 200-300 Gg/year of CH 3 Br may be produced. Indirect emissions from automobile exhaust and biomass burning can not be well quantified (1-10 Gg/year). A global trend of 0.1-0.2 ppt/year is predicted. Model results show significant vertical and seasonal variations in the atmospheric abundances and interhemispheric gradients of CH 3 Br. Substantial uncertainties in calibrations, source estimates, and deposition processes are present. 12 refs., 3 figs., 2 tabs

  14. Phosphorescent quantum dots/ethidium bromide nanohybrids based on photoinduced electron transfer for DNA detection.

    Science.gov (United States)

    Bi, Lin; Yu, Yuan-Hua

    2015-04-05

    Mercaptopropionic acid-capped Mn-doped ZnS quantum dots/ethidium bromide (EB) nanohybrids were constructed for photoinduced electron transfer (PIET) and then used as a room-temperature phosphorescence (RTP) probe for DNA detection. EB could quench the RTP of Mn-doped ZnS QDs by PIET, thereby forming Mn-doped ZnS QDs/EB nanohybrids and storing RTP. Meanwhile, EB could be inserted into DNA and EB could be competitively desorbed from the surface of Mn-doped ZnS QDs by DNA, thereby releasing the RTP of Mn-doped ZnS QDs. Based on this mechanism, a RTP sensor for DNA detection was developed. Under optimal conditions, the detection limit for DNA was 0.045 mg L(-1), the relative standard deviation was 1.7%, and the method linear ranged from 0.2 to 20 mg L(-1). The proposed method was applied to biological fluids, in which satisfactory results were obtained. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Hydrogen Storage Capacity of Tetrahydrofuran and Tetra-N-Butylammonium Bromide Hydrates Under Favorable Thermodynamic Conditions

    Directory of Open Access Journals (Sweden)

    Joshua T. Weissman

    2017-08-01

    Full Text Available An experimental study was conducted to evaluate the feasibility of employing binary hydrates as a medium for H2 storage. Two reagents, tetrahydrofuran (THF and tetra-n-butylammonium bromide (TBAB, which had been reported previously to have potential to form binary hydrates with H2 under favorable conditions (i.e., low pressures and high temperatures, were investigated using differential scanning calorimetry and Raman spectroscopy. A scale-up facility was employed to quantify the hydrogen storage capacity of THF binary hydrate. Gas chromatography (GC and pressure drop analyses indicated that the weight percentages of H2 in hydrate were less than 0.1%. The major conclusions of this investigation were: (1 H2 can be stored in binary hydrates at relatively modest pressures and temperatures which are probably feasible for transportation applications; and (2 the storage capacity of H2 in binary hydrate formed from aqueous solutions of THF over a concentration range extending from 2.78 to 8.34 mol % and at temperatures above 263 K and pressures below 11 MPa was <0.1 wt %.

  16. Sodium bromide electron-extraction layers for polymer bulk-heterojunction solar cells

    International Nuclear Information System (INIS)

    Gao, Zhi; Qu, Bo; Xiao, Lixin; Chen, Zhijian; Zhang, Lipei; Gong, Qihuang

    2014-01-01

    Inexpensive and non-toxic sodium bromide (NaBr) was introduced into polymer solar cells (PSCs) as the cathode buffer layer (CBL) and the electron extraction characteristics of the NaBr CBL were investigated in detail. The PSCs based on NaBr CBL with different thicknesses (i.e., 0 nm, 0.5 nm, 1 nm, and 1.5 nm) were prepared and studied. The optimal thickness of NaBr was 1 nm according to the photovoltaic data of PSCs. The open-circuit voltage (V oc ), short-circuit current density (J sc ), fill factor (FF), and power conversion efficiency (PCE) of the PSC with 1 nm NaBr were evaluated to be 0.58 V, 7.36 mA/cm 2 , 0.63, and 2.70%, respectively, which were comparable to those of the reference device with the commonly used LiF. The optimized photovoltaic performance of PSC with 1 nm NaBr was ascribed to the improved electron transport and extraction capability of 1 nm NaBr in PSCs. In addition, the NaBr CBL could prevent the diffusion of oxygen and water vapor into the active layer and prolong the lifetime of the devices to some extent. Therefore, NaBr layer could be considered as a promising non-toxic CBL for PSCs in future

  17. XRD, TEM, and thermal analysis of Arizona Ca-montmorillonites modified with didodecyldimethylammonium bromide.

    Science.gov (United States)

    Sun, Zhiming; Park, Yuri; Zheng, Shuilin; Ayoko, Godwin A; Frost, Ray L

    2013-10-15

    An Arizona SAz-2 calcium montmorillonite was modified by a typical dialkyl cationic surfactant (didodecyldimethylammonium bromide, abbreviated to DDDMA) through direct ion exchange. The obtained organoclays were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), high-resolution thermogravimetric analysis (HR-TG), and infrared emission spectroscopy (IES). The intercalation of surfactants greatly increased the basal spacing of the interlayers and the conformation arrangement of the loaded surfactant were assessed based on the XRD and TEM measurements. This work shows that the dialkyl surfactant can be directly intercalated into the montmorillonite without first undergoing Na(+) exchange. Moreover, the thermal stability of organoclays and the different arrangements of the surfactant molecules intercalated in the SAz-2 Ca-montmorillonite were determined by a combination of TG and IES techniques. The detailed conformational ordering of different intercalated surfactants under different conditions was also studied. The surfactant molecule DDDMA has proved to be thermally stable even at 400°C which indicates that the prepared organoclay is stable to significantly high temperatures. This study offers new insights into the structure and thermal stabilities of SAz-2 Ca-montmorillonite modified with DDDMA. The experimental results also confirm the potential applications of organic SAz-2 Ca-montmorillonites as adsorbents and polymer-clay nanocomposites. Copyright © 2013 Elsevier Inc. All rights reserved.

  18. Electrical conductivity studies on Ammonium bromide incorporated with Zwitterionic polymer blend electrolyte for battery application

    Science.gov (United States)

    Parameswaran, V.; Nallamuthu, N.; Devendran, P.; Nagarajan, E. R.; Manikandan, A.

    2017-06-01

    Solid polymer blend electrolytes are widely studied due to their extensive applications particularly in electrochemical devices. Blending polymer makes the thermal stability, higher mechanical strength and inorganic salt provide ionic charge carrier to enhance the conductivity. In these studies, 50% polyvinyl alcohol (PVA), 50% poly (N-vinyl pyrrolidone) (PVP) and 2.5% L-Asparagine mixed with different ratio of the Ammonium bromide (NH4Br), have been synthesized using solution casting technique. The prepared PVA/PVP/L-Asparagine/doped-NH4Br polymer blend electrolyte films have been characterized by various analytical methods such as FT-IR, XRD, impedance spectroscopy, TG-DSC and scanning electron microscopy. FT-IR, XRD and TG/DSC analysis revealed the structural and thermal behavior of the complex formation between PVA/PVP/L-Asparagine/doped-NH4Br. The ionic conductivity and the dielectric properties of PVA/PVP/L-Asparagine/doped-NH4Br polymer blend electrolyte films were examined using impedance analysis. The highest ionic conductivity was found to be 2.34×10-4 S cm-1 for the m.wt. composition of 50%PVA:50%PVP:2.5%L-Asparagine:doped 0.15 g NH4Br at ambient temperature. Solid state proton battery is fabricated and the observed open circuit voltage is 1.1 V and its performance has been studied.

  19. Sodium Hypochlorite and Sodium Bromide Individualized and Stabilized Carbon Nanotubes in Water

    KAUST Repository

    Xu, Xuezhu

    2017-09-20

    Aggregation is a major problem for hydrophobic carbon nanomaterials such as carbon nanotubes (CNTs) in water because it reduces the effective particle concentration, prevents particles from entering the medium, and leads to unstable electronic device performances when a colloidal solution is used. Molecular ligands such as surfactants can help the particles to disperse, but they tend to degrade the electrical properties of CNTs. Therefore, self-dispersed particles without the need for surfactant are highly desirable. We report here, for the first time to our knowledge, that CNT particles with negatively charged hydrophobic/water interfaces can easily self-disperse themselves in water via pretreating the nanotubes with a salt solution with a low concentration of sodium hypochlorite (NaClO) and sodium bromide (NaBr). The obtained aqueous CNT suspensions exhibit stable and superior colloidal performances. A series of pH titration experiments confirmed the presence and role of the electrical double layers on the surface of the salted carbon nanotubes and of functional groups and provided an in-depth understanding of the phenomenon.

  20. 76 FR 29238 - Methyl Bromide; Cancellation Order for Registration Amendments To Terminate Certain Soil Uses

    Science.gov (United States)

    2011-05-20

    ...This notice announces EPA's order for the amendments to terminate soil uses, voluntarily requested by the registrants and accepted by the Agency, of products containing methyl bromide, pursuant to section 6(f)(1) of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), as amended. This cancellation order follows a February 9, 2011, Federal Register Notice of Receipt of Requests from the registrants listed in Table 2 of Unit II to voluntarily amend to terminate uses of these product registrations. These are not the last products containing this pesticide registered for use in the United States. In that notice, EPA indicated that it would issue an order implementing the amendments to terminate uses, unless the Agency received substantive comments within the 30-day comment period that would merit its further review of these requests, or unless the registrants withdrew their requests. The Agency did not receive any comments on the notice. Further, the registrants did not withdraw their requests. These amendments do not affect post-harvest fumigant uses. Any distribution, sale, or use of the products subject to this cancellation order is permitted only in accordance with the terms of this order, including any existing stocks provisions.

  1. Mathematical Model of a Lithium-Bromide/Water Absorption Refrigeration System Equipped with an Adiabatic Absorber

    Directory of Open Access Journals (Sweden)

    Salem M. Osta-Omar

    2016-11-01

    Full Text Available The objective of this paper is to develop a mathematical model for thermodynamic analysis of an absorption refrigeration system equipped with an adiabatic absorber using a lithium-bromide/water (LiBr/water pair as the working fluid. The working temperature of the generator, adiabatic absorber, condenser, evaporator, the cooling capacity of the system, and the ratio of the solution mass flow rate at the circulation pump to that at the solution pump are used as input data. The model evaluates the thermodynamic properties of all state points, the heat transfer in each component, the various mass flow rates, and the coefficient of performance (COP of the cycle. The results are used to investigate the effect of key parameters on the overall performance of the system. For instance, increasing the generator temperatures and decreasing the adiabatic absorber temperatures can increase the COP of the cycle. The results of this mathematical model can be used for designing and sizing new LiBr/water absorption refrigeration systems equipped with an adiabatic absorber or for optimizing existing aforementioned systems.

  2. Photocontrol of Voltage-Gated Ion Channel Activity by Azobenzene Trimethylammonium Bromide in Neonatal Rat Cardiomyocytes.

    Directory of Open Access Journals (Sweden)

    Sheyda R Frolova

    Full Text Available The ability of azobenzene trimethylammonium bromide (azoTAB to sensitize cardiac tissue excitability to light was recently reported. The dark, thermally relaxed trans- isomer of azoTAB suppressed spontaneous activity and excitation propagation speed, whereas the cis- isomer had no detectable effect on the electrical properties of cardiomyocyte monolayers. As the membrane potential of cardiac cells is mainly controlled by activity of voltage-gated ion channels, this study examined whether the sensitization effect of azoTAB was exerted primarily via the modulation of voltage-gated ion channel activity. The effects of trans- and cis- isomers of azoTAB on voltage-dependent sodium (INav, calcium (ICav, and potassium (IKv currents in isolated neonatal rat cardiomyocytes were investigated using the whole-cell patch-clamp technique. The experiments showed that azoTAB modulated ion currents, causing suppression of sodium (Na+ and calcium (Ca2+ currents and potentiation of net potassium (K+ currents. This finding confirms that azoTAB-effect on cardiac tissue excitability do indeed result from modulation of voltage-gated ion channels responsible for action potential.

  3. Removal of nitrate from aqueous solution using cetylpyridinium bromide (CPB) modified zeolite as adsorbent

    International Nuclear Information System (INIS)

    Zhan Yanhui; Lin Jianwei; Zhu Zhiliang

    2011-01-01

    Surfactant modified zeolites (SMZ) with different coverage types were prepared by loading the cetylpyridinium bromide (CPB) onto the surface of the natural zeolites. The adsorption behavior of nitrate on SMZ was investigated. Natural zeolite and SMZ with monolayer CPB coverage were inefficient for the removal of nitrate from aqueous solution. However, SMZ with patchy bilayer or bilayer CPB coverage was efficient in nitrate removal, and the nitrate adsorption capacity of SMZ increased with its CPB loading. For typical SMZ with bilayer CPB coverage, the nitrate adsorption process was well described by the pseudo-second-order kinetic model, and the experimental isotherm data fitted well with the Langmuir, Freundlich and Dubinin-Redushkevich isotherm models. Thermodynamic parameters such as Gibbs free energy change, enthalpy change and entropy change were calculated and the results showed that the adsorption of nitrate on SMZ was spontaneous and exothermic in nature. The presence of competing anions such as chloride, sulfate and bicarbonate ions slightly reduced the nitrate adsorption efficiency. Anionic exchange and electrostatic interaction were proven to be the main mechanisms that govern the adsorption of nitrate on SMZ.

  4. Permanganate-bromide-silver nanoparticles as a new chemiluminescence system and its application to captopril determination.

    Science.gov (United States)

    Amjadi, Mohammad; Manzoori, Jamshid L; Hassanzadeh, Javad; Sorouraddin, Mohammad H

    2013-10-15

    A novel chemiluminescence (CL) system based on the oxidation of bromide by permanganate in sulfuric acid medium is introduced. The enhancing effect of silver nanoparticles (NPs), synthesized by chemical reduction method, on this reaction was studied. It was demonstrated that spherical silver nanoparticles with average size of 18 nm had a most remarkable catalytic effect on this reaction. CL emission wavelengths and UV-vis spectra were used to characterize the system and propose a possible mechanism. Furthermore, it was found that captopril inhibits the action of NPs and decreases the intensity of CL. Based on this phenomenon, a new CL method was developed for the determination of captopril in the 3.0 × 10(-10) to 1.0 × 10(-7) mol L(-1) concentration range with a detection limit (3s) of 0.12 nmol L(-1). The method was successfully applied to the determination of captopril in pharmaceutical formulations, human urine and serum samples. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. Influence of pyridostigmine bromide on human thermoregulation during cold-water immersion

    Energy Technology Data Exchange (ETDEWEB)

    Cadarette, B.S.; Prusaczyk, W.K.; Sawka, M.N. (Army Research Inst. of Environmental Medicine, Natick, MA (United States))

    1991-03-11

    This study examined the effects of an oral 30 mg dose of pyridostigmine bromide (PYR) on thermoregulatory and physiological responses during cold stress. Six men were immersed in chilled stirred water for up to 180 minutes; once 2 hours following ingestion of PYR and once 2 hours following ingestion of a placebo (CON). With PYR, mean ({plus minus} SD) red blood cell cholinesterase inhibition was 33 ({plus minus}12)% at 110 minutes post-ingestion. Cholinesterase inhibition was negatively related to lean body mass. Abdominal discomfort caused termination in 3 of 6 PYR experiments ({bar X} immersion time = 117 min) but in no CON experiments ({bar X} immersion time = 142 min, p > 0.05). During immersion, metabolic rate increased significantly over pre-immersion levels, and increased with duration of immersion, but did not differ between conditions. PYR had no significant effect on rectal temperature, mean body temperature, thermal sensation, heart rate, or plasma cortisol concentration. It was concluded that a 30 mg dose of PYR does not increase susceptibility to hypothermia in humans immersed in cold-water; however, in combination with cold-stress, PYR may result in marked abdominal cramping and limit cold tolerance.

  6. Removal of hexavalent chromium by using red mud activated with cetyltrimethylammonium bromide.

    Science.gov (United States)

    Li, Deliang; Ding, Ying; Li, Lingling; Chang, Zhixian; Rao, Zhengyong; Lu, Ling

    2015-01-01

    The removal of hexavalent chromium [Cr(VI)] from aqueous solution by using red mud activated with cetyltrimethylammonium bromide (CTAB) was studied. The optimum operation parameters, such as CTAB concentration, pH values, contact time, and initial Cr(VI) concentration, were investigated. The best concentration of CTAB for modifying red mud was found to be 0.50% (mCTAB/VHCl,0.6 mol/L). The lower pH (mud activated with CTAB can greatly improve the removal ratio of Cr(VI) as high as four times than that of original red mud. Adsorption equilibrium was reached within 30 min under the initial Cr(VI) concentration of 100 mg L(-1). The isotherm data were analysed using Langmuir and Freundlich models. The adsorption of Cr(VI) on activated red mud fitted well to the Langmuir isotherm model, and the maximum adsorption capacity was estimated as 22.20 mg g(-1) (Cr/red mud). The adsorption process could be well described using the pseudo-second-order model. The result shows that activated red mud is a promising agent for low-cost water treatment.

  7. A Facile Electrochemical Sensor for Nonylphenol Determination Based on the Enhancement Effect of Cetyltrimethylammonium Bromide

    Directory of Open Access Journals (Sweden)

    Qing Lu

    2013-01-01

    Full Text Available A facile electrochemical sensor for the determination of nonylphenol (NP was fabricated in this work. Cetyltrimethylammonium bromide (CTAB, which formed a bilayer on the surface of the carbon paste (CP electrode, displayed a remarkable enhancement effect for the electrochemical oxidation of NP. Moreover, the oxidation peak current of NP at the CTAB/CP electrode demonstrated a linear relationship with NP concentration, which could be applied in the direct determination of NP. Some experimental parameters were investigated, such as external solution pH, mode and time of accumulation, concentration and modification time of CTAB and so on. Under optimized conditions, a wide linear range from 1.0 × 10−7 mol·L−1 to 2.5 × 10−5 mol·L−1 was obtained for the sensor, with a low limit of detection at 1.0 × 10−8 mol·L−1. Several distinguishing advantages of the as-prepared sensor, including facile fabrication, easy operation, low cost and so on, suggest a great potential for its practical applications.

  8. Prediction of strontium bromide laser efficiency using cluster and decision tree analysis

    Directory of Open Access Journals (Sweden)

    Iliev Iliycho

    2018-01-01

    Full Text Available Subject of investigation is a new high-powered strontium bromide (SrBr2 vapor laser emitting in multiline region of wavelengths. The laser is an alternative to the atom strontium lasers and electron free lasers, especially at the line 6.45 μm which line is used in surgery for medical processing of biological tissues and bones with minimal damage. In this paper the experimental data from measurements of operational and output characteristics of the laser are statistically processed by means of cluster analysis and tree-based regression techniques. The aim is to extract the more important relationships and dependences from the available data which influence the increase of the overall laser efficiency. There are constructed and analyzed a set of cluster models. It is shown by using different cluster methods that the seven investigated operational characteristics (laser tube diameter, length, supplied electrical power, and others and laser efficiency are combined in 2 clusters. By the built regression tree models using Classification and Regression Trees (CART technique there are obtained dependences to predict the values of efficiency, and especially the maximum efficiency with over 95% accuracy.

  9. Kinetics and mechanism of the pyridinolysis of phenacyl bromides in acetonitrile

    Science.gov (United States)

    Koh; Han; Lee; Lee

    2000-07-28

    Kinetic studies of the reactions of substituted phenacyl bromides (YC6H4COCH2Br) with pyridines (XC5H4N) are carried out in acetonitrile at 45.0 degrees C. A biphasic Bronsted plot is obtained with a change in slope from a large (betaX approximately equals 0.65-0.80) to a small (betaX approximately 0.36-0.40) value at pKa = 3.2-3.6, which can be attributed to a change in the rate-determining step from breakdown to formation of a tetrahedral intermediate in the reaction path as the basicity of the pyridine nucleophile increases. This mechanism is supported by the faster rates with pyridines than with anilines and the change of cross-interaction constant rhoXY from a large positive (rhoXY = +1.4) to a small positive (rhoXY approximately +0.1) value. The large magnitude of Hammett rhoX (= -5.5 to -6.9) values for the pyridines with electron-withdrawing substituents and positive deviations of the pi-acceptors, p-CH3CO and p-CN, are quite similar to those for the pyridinium ion formation equilibria. The activation parameters are also in line with the proposed mechanism.

  10. Low-Dimensional Organic Tin Bromide Perovskites and Their Photoinduced Structural Transformation.

    Science.gov (United States)

    Zhou, Chenkun; Tian, Yu; Wang, Mingchao; Rose, Alyssa; Besara, Tiglet; Doyle, Nicholas K; Yuan, Zhao; Wang, Jamie C; Clark, Ronald; Hu, Yanyan; Siegrist, Theo; Lin, Shangchao; Ma, Biwu

    2017-07-24

    Hybrid organic-inorganic metal halide perovskites possess exceptional structural tunability, with three- (3D), two- (2D), one- (1D), and zero-dimensional (0D) structures on the molecular level all possible. While remarkable progress has been realized in perovskite research in recent years, the focus has been mainly on 3D and 2D structures, with 1D and 0D structures significantly underexplored. The synthesis and characterization of a series of low-dimensional organic tin bromide perovskites with 1D and 0D structures is reported. Using the same organic and inorganic components, but at different ratios and reaction conditions, both 1D (C 4 N 2 H 14 )SnBr 4 and 0D (C 4 N 2 H 14 Br) 4 SnBr 6 can be prepared in high yields. Moreover, photoinduced structural transformation from 1D to 0D was investigated experimentally and theoretically in which photodissociation of 1D metal halide chains followed by structural reorganization leads to the formation of a more thermodynamically stable 0D structure. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Removal of bromide and bromate from drinking water using granular activated carbon.

    Science.gov (United States)

    Zhang, Yong-Qing; Wu, Qing-Ping; Zhang, Ju-Mei; Yang, Xiu-Hua

    2015-03-01

    Granular activated carbon (GAC) was used to remove bromide (Br⁻) and bromate (BrO(3)(-)) from drinking water in both bench- and pilot-scale experiments. The present study aims to minimize BrO(3)(-) formation and eliminate BrO(3)(-) generated during the ozonation of drinking water, particularly in packaged drinking water. Results show that the Br⁻ and BrO(3)(-) levels in GAC-treated water decreased in both bench- and pilot-scale experiments. In the bench-scale experiments, when the empty bed contact time (EBCT) was 5 min, the highest reduction rates of Br(-) in the mineral and ultrapure water were found to be 74.9% and 91.2%, respectively, and those of BrO(3)(-) were 94.4% and 98.8%, respectively. The GAC capacity for Br⁻ and BrO(3)(-) removal increased with the increase in EBCT. Reduction efficiency was better in ultrapure water than in mineral water. In the pilot-scale experiments, the minimum reduction rates of Br⁻ and BrO(3)(-) were 38.5% and 73.2%, respectively.

  12. Synthesis, characterization and antibacterial properties of dihydroxy quaternary ammonium salts with long chain alkyl bromides.

    Science.gov (United States)

    Liu, Wen-Shuai; Wang, Chun-Hua; Sun, Ju-Feng; Hou, Gui-Ge; Wang, Yu-Peng; Qu, Rong-Jun

    2015-01-01

    Five N-methyl-N-R-N,N-bis(2-hydroxyethyl) ammonium bromides (R = -benzyl (chloride, BNQAS), -dodecyl (C12QAS), -tetradecyl (C14QAS), -hexadecyl (C16QAS), -octadecyl (C18QAS)) were prepared based on N-methyldiethanolamine (MDEA) and halohydrocarbon. Five QAS were characterized by FTIR, NMR, and MS. BNQAS, C12QAS, C14QAS, and C16QAS were confirmed by X-ray single-crystal diffraction. Their antibacterial properties indicated good antibacterial abilities against E. coli, S. aureus, B. subtilis, especially C12QAS with the best antibacterial ability (100% to E. coli, 95.65% to S. aureus, and 91.41% to B. subtilis). In addition, C12QAS also displayed the best antifungal activities than BNQAS and C18QAS against Cytospora mandshurica, Botryosphaeria ribis, Physalospora piricola, and Glomerella cingulata with the ratio of full marks. The strategy provides a facile way to design and develop new types of antibacterial drugs for application in preventing the fruit rot, especially apple. © 2014 John Wiley & Sons A/S.

  13. Single nucleotide polymorphism discrimination with and without an ethidium bromide intercalator.

    Science.gov (United States)

    Fenati, Renzo A; Connolly, Ashley R; Ellis, Amanda V

    2017-02-15

    Single nucleotide polymorphism (SNP) genotyping is an important aspect in understanding genetic variations. Here, we discriminate SNPs using toe-hold mediated displacement reactions. The biological target is an 80 nucleotide long double-stranded-DNA from the mtDNA HV1 region, associated with maternal ancestry. This target has been specially designed with a pendant toehold and a cationic fluorophore, ATTO 647N, as a reporter, produced in a polymerase chain reaction. Rates of reaction for the toehold-polymerase chain reaction products (TPPs) with their corresponding complementary displacing sequences, labelled with a Black Hole Quencher 1, followed the order TPP-Cytosine > TPP-Thymine > TPP-Adenine ≥ TPP-Guanine. Non-complementary rates were the slowest with mismatches involving cytosine. These reactions, operating in a static/or contact mode, gave averaged readouts between SNPs within 15 min (with 80-90% quenching), compared to 25-30 min in previous studies involving fluorescence resonance energy transfer. Addition of an intercalating agent, ethidium bromide, retarded the rate of reaction in which cytosine was involved, presumably through stabilization of the base pairing, which resulted in markedly improved discrimination of cytosine containing SNPs. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. Energetic and binding properties of DNA upon interaction with dodecyl trimethylammonium bromide.

    Science.gov (United States)

    Bathaie, S Z; Moosavi-Movahedi, A A; Saboury, A A

    1999-02-15

    The interaction of dodecyl trimethylammonium bromide (DTAB), a cationic surfactant, with calf thymus DNA has been studied by various methods, including potentiometric technique using DTAB-selective plastic membrane electrode at 27 and 37 degreesC, isothermal titration microcalorimetry and UV spectrophotometry at 27 degreesC using 0.05 M Tris buffer and 0.01 M NaCl at pH 7.4. The free energy is calculated from binding isotherms on the basis of Wyman binding potential theory and the enthalpy of binding according to van't Hoff relation. The enthalpy of unfolding has been determined by subtraction of the enthalpy of binding from the microcalorimetric enthalpy. The results show that, after the interaction of first DTAB molecule to DNA (base molarity) through the electrostatic interaction, the second DTAB molecule also binds to DNA through electrostatic interaction. At this stage, the predom-inant DNA conformational change occurs. Afterwards up to 20 DTAB molecules, below the critical micelle concentration of DTAB, bind through hydrophobic interactions.

  15. Carboxymethylcellulose acetate butyrate/poly(4-vinyl-N-pentyl pyridinium bromide blends as antimicrobial coatings

    Directory of Open Access Journals (Sweden)

    L. S. Blachechen

    2015-09-01

    Full Text Available Blends of carboxymethyl cellulose acetate butyrate (CMCAB, a cellulose derivative, and poly(4-vinyl-N-pentyl pyridinium bromide (QPVP-C5, an antimicrobial polymer, were prepared by casting method and characterized by means of Fourier transform infrared vibrational spectroscopy (FTIR, scanning electron microscopy (SEM, thermogravimetric analysis (TGA, differential scanning calorimetry (DSC and contact angle measurements. Miscibility between CMCAB and QPVP-C5 was evidenced by DSC measurements of blends, which showed a single thermal event of Tg, and SEM images, which revealed homogenous morphology, regardless the blend composition. Moreover, thermal stability of QPVP-C5 was substantially enhanced, when it was mixed with CMCAB. Upon increasing the QPVP-C5 content in the blend the wettability and antimicrobial activity against Gram-positive bacteria Micrococcus luteus increased, indicating the surface enrichment by pyridinium groups. In fact, blends with 70 wt% QPVP-C5 reduced 5 log and 4 log the colony-forming units of Micrococcus luteus and Escherichia coli, respectively.

  16. Reversal or protection by light of the ethidium bromide induced petite mutation in yeast

    International Nuclear Information System (INIS)

    Hixon, S.C.; Burnham, A.D.; Irons, R.L.

    1979-01-01

    An intermediate in the ethidium bromide (EB) induced petite mutation pathway may be destabilized by daylight light to cause a reversion to the normal grande phenotype. Starved cells preincubated in the dark for up to 6 h with 100μg/ml EB could be reverted to grandes after one hour of light exposure, whereas similarly treated cells maintained in the dark expresse the petite mutation in more than 80 percent of the population. In addition, the production of petite mutants by EB in buffer could be prevented if cell suspensions were exposed to light immediately upon the addition of EB. Photoreversal of the EB-derived petite mutation in growing cells as less efficient presumably because the availability of an energy source caused a continuation of mutation events beyond the light revertible step to a non-reversible fixation of the mutation. Cells treated with EB in growth and reversal of the mutation. This may be due to the cold inhibition of an enzyme which comes into play beyond the light sensitive step in the mutation pathway. (orig.) [de

  17. The effects of cetyltrimethylammonium bromide surfactant on alumina modified zinc oxides

    Energy Technology Data Exchange (ETDEWEB)

    Gac, Wojciech, E-mail: wojciech.gac@umcs.lublin.pl [Department of Chemical Technology, Faculty of Chemistry, Maria Curie-Sklodowska University, 3 M. Curie-Sklodowska Sq., 20-031 Lublin (Poland); Zawadzki, Witold; Słowik, Grzegorz; Pawlonka, Justyna; Machocki, Andrzej [Department of Chemical Technology, Faculty of Chemistry, Maria Curie-Sklodowska University, 3 M. Curie-Sklodowska Sq., 20-031 Lublin (Poland); Lipke, Agnieszka; Majdan, Marek [Department of Inorganic Chemistry, Faculty of Chemistry, Maria Curie-Sklodowska University, 2 M. Curie-Sklodowska Sq., 20-031 Lublin (Poland)

    2016-06-15

    Highlights: • Synthesis of novel ZnO−Al{sub 2}O{sub 3} oxides in the presence of CTAB surfactant. • Determination of the structural, surface and optical properties. • Nanocrystalline, high-surface area ZnO−Al{sub 2}O{sub 3} oxides. • ZnO-Al{sub 2}O{sub 3} materials of different gap energy. - Abstract: Novel alumina modified zinc oxide materials were prepared by co-precipitation method in the presence of different amounts of cetyltrimethylammonium bromide (CTAB) surfactant. X-ray diffraction, {sup 27}Al magic-angle spinning Nuclear Magnetic Resonance Spectroscopy, and transmission electron microscopy studies evidenced formation of 10–15 nm zinc oxide nanoparticles in the presence of the small amounts of surfactant. Amorphous alumina and zinc aluminate phases of different coordination environment of Al sites were identified. An increase of surfactant concentration led to the elongation of nanoparticles and changes of the nature of hydroxyl groups. Precipitation in the high CTAB concentration conditions facilitated formation of mesoporous materials of high specific surface area. The materials were composed of very small (2–3 nm) zinc aluminate spinel nanoparticles. High concentration of CTAB induced widening of band gap energy.

  18. Stable bromine isotopic composition of methyl bromide released from plant matter

    Science.gov (United States)

    Horst, Axel; Holmstrand, Henry; Andersson, Per; Thornton, Brett F.; Wishkerman, Asher; Keppler, Frank; Gustafsson, Örjan

    2014-01-01

    Methyl bromide (CH3Br) emitted from plants constitutes a natural source of bromine to the atmosphere, and is a component in the currently unbalanced global CH3Br budget. In the stratosphere, CH3Br contributes to ozone loss processes. Studies of stable isotope composition may reduce uncertainties in the atmospheric CH3Br budget, but require well-constrained isotope fingerprints of the source end members. Here we report the first measurements of stable bromine isotopes (δ81Br) in CH3Br from abiotic plant emissions. Incubations of both KBr-fortified pectin, a ubiquitous cell-stabilizing macromolecule, and of a natural halophyte (Salicornia fruticosa), yielded an enrichment factor (ε) of -2.00 ± 0.23‰ (1σ, n = 8) for pectin and -1.82 ± 0.02‰ (1σ, n = 4) for Salicornia (the relative amount of the heavier 81Br was decreased in CH3Br compared to the substrate salt). For short incubations, and up to 10% consumption of the salt substrate, this isotope effect was similar for temperatures from 30 up to 300 °C. For longer incubations of up to 90 h at 180 °C the δ81Br values increased from -2‰ to 0‰ for pectin and to -1‰ for Salicornia. These δ81Br source signatures of CH3Br formation from plant matter combine with similar data for carbon isotopes to facilitate multidimensional isotope diagnostics of the CH3Br budget.

  19. Precipitation, stabilization and molecular modeling of ZnS nanoparticles in the presence of cetyltrimethylammonium bromide.

    Science.gov (United States)

    Praus, Petr; Dvorský, Richard; Horínková, Petra; Pospíšil, Miroslav; Kovář, Petr

    2012-07-01

    ZnS nanoparticles were precipitated in aqueous dispersions of cationic surfactant cetyltrimethylammonium bromide (CTAB). The sphere radii of ZnS nanoparticles calculated by using band-gap energies steeply decreased from 4.5 nm to 2.2 nm within CTAB concentrations of 0.4-1.5 mmol L(-1). Above the concentration of 1.5 mmol L(-1), the radii were stabilized at R=2.0 nm and increased up to R=2.5 nm after 24 h. The hydrodynamic diameters of CTAB-ZnS structures observed by the dynamic light scattering (DLS) method ranged from 130 nm to 23 nm depending on CTAB concentrations of 0.5-1.5 mmol L(-1). The complex structures were observed by transmission electron microscopy (TEM). At the higher CTAB concentrations, ZnS nanoparticles were surrounded by CTA(+) bilayers forming positively charged micelles with the diameter of 10nm. The positive zeta-potentials of the micelles and their agglomerates were from 16 mV to 33 mV. Wurtzite and sphalerite nanoparticles with R=2.0 nm and 2.5 nm covered by CTA(+) were modeled with and without water. Calculated sublimation energies confirmed that a bilayer arrangement of CTA(+) on the ZnS nanoparticles was preferred to a monolayer. Copyright © 2012 Elsevier Inc. All rights reserved.

  20. Effects of Nonhydrostatic Stress on Structural and Optoelectronic Properties of Methylammonium Lead Bromide Perovskite

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Rong; Cai, Weizhao; Bi, Tiange; Zarifi, Niloofar; Terpstra, Tyson; Zhang, Chuang; Verdent, Z. Valy; Zurek, Eva; Deemyad, Shanti (Buffalo); (Utah)

    2017-07-13

    We report synchrotron X-ray diffraction, photoconductivity, and photoluminescence investigations of methylammonium-lead-bromide (MAPbBr3) under various stress conditions, supported by density-functional-theory (DFT) calculations. The properties of MAPbBr3 show substantial dependence on the hydrostatic conditions. While nonhydrostatic compression of MAPbBr3 leads to amorphization above 2.4 GPa, under quasi-hydrostatic (Ar) and hydrostatic (He) pressure, the sample remains in crystalline phases. A sequence of phase transitions between two cubic phases and orthorhombic Pnma phase is observed when using Ar, or no pressure-transmitting-medium (PTM). In helium-PTM only transitions between the two cubic structures and a new isostructural phase transition with a large volume collapse to a third cubic-phase at 2.7 GPa was observed. The photoluminescence measurements indicate a pressure-induced band gap-narrowing in the cubic phase I, and a blue-shift in the orthorhombic structure. DFT calculations illustrate that the dynamics of the organic molecules and the inorganic lattice, coupled via the N–H···Br hydrogen-bonding interactions, affect the Pb–Br distance and the bandgap evolution under pressure.

  1. Mitochondrial DNA depletion by ethidium bromide decreases neuronal mitochondrial creatine kinase: Implications for striatal energy metabolism.

    Science.gov (United States)

    Warren, Emily Booth; Aicher, Aidan Edward; Fessel, Joshua Patrick; Konradi, Christine

    2017-01-01

    Mitochondrial DNA (mtDNA), the discrete genome which encodes subunits of the mitochondrial respiratory chain, is present at highly variable copy numbers across cell types. Though severe mtDNA depletion dramatically reduces mitochondrial function, the impact of tissue-specific mtDNA reduction remains debated. Previously, our lab identified reduced mtDNA quantity in the putamen of Parkinson's Disease (PD) patients who had developed L-DOPA Induced Dyskinesia (LID), compared to PD patients who had not developed LID and healthy subjects. Here, we present the consequences of mtDNA depletion by ethidium bromide (EtBr) treatment on the bioenergetic function of primary cultured neurons, astrocytes and neuron-enriched cocultures from rat striatum. We report that EtBr inhibition of mtDNA replication and transcription consistently reduces mitochondrial oxygen consumption, and that neurons are significantly more sensitive to EtBr than astrocytes. EtBr also increases glycolytic activity in astrocytes, whereas in neurons it reduces the expression of mitochondrial creatine kinase mRNA and levels of phosphocreatine. Further, we show that mitochondrial creatine kinase mRNA is similarly downregulated in dyskinetic PD patients, compared to both non-dyskinetic PD patients and healthy subjects. Our data support a hypothesis that reduced striatal mtDNA contributes to energetic dysregulation in the dyskinetic striatum by destabilizing the energy buffering system of the phosphocreatine/creatine shuttle.

  2. Evaluation of methyl bromide alternatives efficacy against soil-borne pathogens, nematodes and soil microbial community.

    Directory of Open Access Journals (Sweden)

    Hongwei Xie

    Full Text Available Methyl bromide (MB and other alternatives were evaluated for suppression of Fusarium spp., Phytophthora spp., and Meloidogyne spp. and their influence on soil microbial communities. Both Fusarium spp. and Phytophthora spp. were significantly reduced by the MB (30.74 mg kg-1, methyl iodide (MI: 45.58 mg kg-1, metham sodium (MS: 53.92 mg kg-1 treatments. MS exhibited comparable effectiveness to MB in controlling Meloidogyne spp. and total nematodes, followed by MI at the tested rate. By contrast, sulfuryl fluoride (SF: 33.04 mg kg-1 and chloroform (CF: 23.68 mg kg-1 showed low efficacy in controlling Fusarium spp., Phytophthora spp., and Meloidogyne spp. MB, MI and MS significantly lowered the abundance of different microbial populations and microbial biomass in soil, whereas SF and CF had limited influence on them compared with the control. Diversity indices in Biolog studies decreased in response to fumigation, but no significant difference was found among treatments in PLFA studies. Principal component and cluster analyses of Biolog and PLFA data sets revealed that MB and MI treatments greatly influenced the soil microbial community functional and structural diversity compared with SF treatment. These results suggest that fumigants with high effectiveness in suppressing soil-borne disease could significantly influence soil microbial community.

  3. Thermochemistry of adducts of some bivalent transition metal bromides with aniline

    International Nuclear Information System (INIS)

    Dunstan, Pedro Oliver

    2006-01-01

    The compounds [MBr 2 (an) 2 ] (where M is Mn(II), Fe(II), Co(II), Ni(II), Cu(II) or Zn(II); an=aniline) were synthesized and characterized by melting points, elemental analysis, thermal studies, and electronic and IR spectroscopy. The enthalpies of dissolution of the adducts, metal(II) bromides and aniline in methanol, aqueous 1.2M HCl or 25% (v/v) aqueous 1.2M HCl in methanol were measured. The following thermochemical parameters for the adducts have been determined by thermochemical cycles: the standard enthalpies for the Lewis acid/base reactions (Δ r H o ), the standard enthalpies of formation (Δ f H o ), the standard enthalpies of decomposition (Δ D H o ), the lattice standard enthalpies (Δ M H o ) and the standard enthalpies of the Lewis acid/base reactions in the gaseous phase (Δ r H o (g)). The mean bond dissociation enthalpies of the M(II)-nitrogen bonds (D-bar (M?N) ) and the enthalpies of formation of the adducts from the ions in the gaseous phase: M 2+ (g) +Br - (g) +an (g) ->[MBr 2 (an) 2 ] (g) (Δ fi H o ) have been estimated

  4. Room temperature X- and gamma-ray detectors using thallium bromide crystals

    CERN Document Server

    Hitomi, K; Shoji, T; Suehiro, T; Hiratate, Y

    1999-01-01

    Thallium bromide (TlBr) is a compound semiconductor with wide band gap (2.68 eV) and high X- and gamma-ray stopping power. The TlBr crystals were grown by the horizontal travelling molten zone (TMZ) method using purified material. Two types of room temperature X- and gamma-ray detectors were fabricated from the TlBr crystals: TlBr detectors with high detection efficiency for positron annihilation gamma-ray (511 keV) detection and TlBr detectors with high-energy resolution for low-energy X-ray detection. The detector of the former type demonstrated energy resolution of 56 keV FWHM (11%) for 511 keV gamma-rays. Energy resolution of 1.81 keV FWHM for 5.9 keV was obtained from the detector of the latter type. In order to analyze noise characteristics of the detector-preamplifier assembly, the equivalent noise charge (ENC) was measured as a function of the amplifier shaping time for the high-resolution detector. This analysis shows that parallel white noise and 1/f noise were dominant noise sources in the detector...

  5. Binding of dyes to hydroxyapatite treated with cetylpyridinium chloride or cetrimonium bromide.

    Science.gov (United States)

    Jensen, J E

    1978-03-01

    The effect of cetylpyridinium chloride (CPC) and cetrimonium bromide (CTAB) on the adsorption of some acidic food dyes to hydroxyapatite was studied. The dyes investigated were brilliant blue (FD&C Blue No. 1), tartrazine (FD&C Yellow No. 5), sunset yellow (FD&C Yellow No. 6) and amaranth (FD&C Red No. 2). The apatite had adsorbed 9.2 mumol CPC per g dry weight. The adsorbed CPC was in equilibrium with a free concentration of 20 microgram/ml (58 micrometer). The adsorption of CPC and CTAB to the apatite was followed by an increased ability of the crystals to bind the dyes. The dyes were very firmly adsorbed and were not released during a series of washings. Untreated apatite showed only a minor affinity for the dyes. The adsorbed dyes were easily washed out. CPC and CTAB showed the smae specific ability to increase the binding capacity of the apatite. The results are discussed and related to the formation of stains on the teeth in persons using quaternary ammonium compounds for mouthrinsing. A mechanism explaining the production of stains is proposed.

  6. Synthesis of zeolitic materials from volcanic ash in presence and absence of cetyltrimethylammonium bromide

    Energy Technology Data Exchange (ETDEWEB)

    Sanhueza N, V. M.; Bennun T, L. D., E-mail: vsanhuez@udec.cl [Universidad de Concepcion, Facultad de Ciencias Quimicas, Edmundo Larenas 129, Region del Biobio (Chile)

    2015-07-01

    Zeolitic materials as Na-phillipsite, Na-K-phillipsite-like zeolites and the mixtures of zeolites (phillipsite+analcime and phillipsite+chabazite+analcime) were synthesized from volcanic ash, either in presence and absence of cetiltrimetilamonium bromide (CTAB). The ash sample used in the laboratory experiments contains 75.36% SiO{sub 2} and 14.11% Al{sub 2}O{sub 3}, abundances. The reaction time as well as the influence of CTAB were studied in the zeolitic materials crystallization. The experiments were carried out under hydrothermal conditions, autogenic pressure and temperature of 150 grades C, as well as reaction time from 8 to 116 h. Products from this hydrothermal treatment were identified by X-ray diffraction (XRD) and characterized by scanning electron microscopy-energy dispersive X-ray spectroscopy (Sem-EDS). Of the zeolitic materials obtained the Na-K-phillipsite-like zeolite was found to be the most effective for the retention of cations Pb{sup 2+}, Zn{sup 2+} and Ba{sup 2+}. (Author)

  7. Cervical spinal demyelination with ethidium bromide impairs respiratory (phrenic) activity and forelimb motor behavior in rats

    Science.gov (United States)

    Nichols, Nicole L.; Punzo, Antonio M.; Duncan, Ian D.; Mitchell, Gordon S.; Johnson, Rebecca A.

    2012-01-01

    Although respiratory complications are a major cause of morbidity/mortality in many neural injuries or diseases, little is known concerning mechanisms whereby deficient myelin impairs breathing, or how patients compensate for such changes. Here, we tested the hypothesis that respiratory and forelimb motor function are impaired in a rat model of focal dorsolateral spinal demyelination (ethidium bromide, EB). Ventilation, phrenic nerve activity and horizontal ladder walking were performed 7-14 days post-C2 injection of EB or vehicle (SHAM). EB caused dorsolateral demyelination at C2-C3 followed by signficant spontaneous remyelination at 14 days post-EB. Although ventilation did not differ between groups, ipsilateral integrated phrenic nerve burst amplitude was significantly reduced versus SHAM during chemoreceptor activation at 7 days post-EB but recovered by 14 days. The ratio of ipsi- to contralateral phrenic nerve amplitude correlated with cross-sectional lesion area. This ratio was significantly reduced 7 days post-EB versus SHAM during baseline conditions, and versus SHAM and 14 day groups during chemoreceptor activation. Limb function ipsilateral to EB was impaired 7 days post-EB and partially recovered by 14 days post-EB. EB provides a reversible model of focal, spinal demyelination, and may be a useful model to study mechanisms of functional impairment and recovery via motor plasticity, or the efficacy of new therapeutic interventions to reduce severity or duration of disease. PMID:23159317

  8. Lithium bromide high-temperature absorption heat pump: coefficient of performance and exergetic efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Izquierdo, M [Consejo Superior de Investigaciones Cientificas, Madrid (ES). Inst. de Optica; Aroca, S [Escuela Tecnica Superior de Ingenieros Industriales, Valladolid (ES). Catedratico de Ingenieria Termica

    1990-04-01

    A theoretical study of a lithium bromide absorption heat pump, used as a machine type I and aimed to produce heat at 120{sup 0}C via waste heat sources at 60{sup 0}C, is given. Real performance conditions are stated for each component of the machine. By means of thermodynamic diagrams (p, t, x) and (h, x), the required data are obtained for calculation of the heat recovered in the evaporator Q{sub e}, the heat delivered to the absorber Q{sub a} and to the condenser Q{sub c}, and the heat supplied to the generator Q{sub g}. The heat delivered by the hot solution to the cold solution in the heat recovered Q{sub r}, and the work W{sub p} done by the solution pump are calculated. The probable COP is calculated as close to 1.4 and the working temperature in the generator ranges from 178 to 200{sup 0}C. The heat produced by the heat pump is 22% cheaper than that obtained from a cogeneration system comprising a natural gas internal combustion engine and high temperature heat pump with mechanical compression. Compared with a high temperature heat pump with mechanical compression, the heat produced by the absorption heat pump is 31% cheaper. From (h, x) and (s, x) diagrams, exergy losses for each component can be determined leading to an exergetic efficiency of 75% which provides the quality index of the absorption cycle. (author).

  9. The challenge of research and extension to define and implement alternatives to methyl bromide.

    Science.gov (United States)

    Noling, J W; Becker, J O

    1994-12-01

    Over the past 30 years, methyl bromide (MBr), a broad spectrum fumigant, has been used extensively for soilborne disease and pest control in the production of many fruit, vegetable, turf, and nursery crops. Recently, agricultural emissions of MBr were implicated as a potentially significant contributor to stratospheric ozone depletion. As a precautionary measure for global ozone protection, the U.S. Environmental Protection Agency has enforced federal legislation which mandates a complete phase-out of MBr use within the United States by 1 January 2001. Thus, new cost effective, environmentally compatible strategies for control of nematodes and other soilborne pests and pathogens must be developed and tested in a relatively short time to avoid significant losses in crop productivity. The extent to which certain agricultural industries that are now heavily reliant on MBr are affected will depend on the development of sustainable, integrated tactics to pest control, such as combinations of cultural, chemical, and biological tactics. New muhidisciplinary research and extension programs must be developed to address and overcome major constraints and incompatibilities that have prevented such tactics from being widely adopted.

  10. Mitochondrial DNA depletion by ethidium bromide decreases neuronal mitochondrial creatine kinase: Implications for striatal energy metabolism.

    Directory of Open Access Journals (Sweden)

    Emily Booth Warren

    Full Text Available Mitochondrial DNA (mtDNA, the discrete genome which encodes subunits of the mitochondrial respiratory chain, is present at highly variable copy numbers across cell types. Though severe mtDNA depletion dramatically reduces mitochondrial function, the impact of tissue-specific mtDNA reduction remains debated. Previously, our lab identified reduced mtDNA quantity in the putamen of Parkinson's Disease (PD patients who had developed L-DOPA Induced Dyskinesia (LID, compared to PD patients who had not developed LID and healthy subjects. Here, we present the consequences of mtDNA depletion by ethidium bromide (EtBr treatment on the bioenergetic function of primary cultured neurons, astrocytes and neuron-enriched cocultures from rat striatum. We report that EtBr inhibition of mtDNA replication and transcription consistently reduces mitochondrial oxygen consumption, and that neurons are significantly more sensitive to EtBr than astrocytes. EtBr also increases glycolytic activity in astrocytes, whereas in neurons it reduces the expression of mitochondrial creatine kinase mRNA and levels of phosphocreatine. Further, we show that mitochondrial creatine kinase mRNA is similarly downregulated in dyskinetic PD patients, compared to both non-dyskinetic PD patients and healthy subjects. Our data support a hypothesis that reduced striatal mtDNA contributes to energetic dysregulation in the dyskinetic striatum by destabilizing the energy buffering system of the phosphocreatine/creatine shuttle.

  11. Sodium Hypochlorite and Sodium Bromide Individualized and Stabilized Carbon Nanotubes in Water

    KAUST Repository

    Xu, Xuezhu; Zhou, Jian; Colombo, Veronica; Xin, Yangyang; Tao, Ran; Lubineau, Gilles

    2017-01-01

    Aggregation is a major problem for hydrophobic carbon nanomaterials such as carbon nanotubes (CNTs) in water because it reduces the effective particle concentration, prevents particles from entering the medium, and leads to unstable electronic device performances when a colloidal solution is used. Molecular ligands such as surfactants can help the particles to disperse, but they tend to degrade the electrical properties of CNTs. Therefore, self-dispersed particles without the need for surfactant are highly desirable. We report here, for the first time to our knowledge, that CNT particles with negatively charged hydrophobic/water interfaces can easily self-disperse themselves in water via pretreating the nanotubes with a salt solution with a low concentration of sodium hypochlorite (NaClO) and sodium bromide (NaBr). The obtained aqueous CNT suspensions exhibit stable and superior colloidal performances. A series of pH titration experiments confirmed the presence and role of the electrical double layers on the surface of the salted carbon nanotubes and of functional groups and provided an in-depth understanding of the phenomenon.

  12. Volumetric properties of the (tetrahydrofuran + water) and (tetra-n-butyl ammonium bromide + water) systems: Experimental measurements and correlations

    International Nuclear Information System (INIS)

    Belandria, Veronica; Mohammadi, Amir H.; Richon, Dominique

    2009-01-01

    In this communication, we report experimental density data for the binary mixtures of (water + tetrahydrofuran) and (water + tetra-n-butyl ammonium bromide) at atmospheric pressure and various temperatures. The densities were measured using an Anton Paar TM digital vibrating-tube densimeter. For the (tetrahydrofuran + water) system, excess molar volumes have been calculated using the experimental densities and correlated using the Redlich-Kister equation. The Redlich-Kister equation parameters have been adjusted on experimental results. The partial molar volumes and partial excess molar volumes at infinite dilution have also been calculated for each component. A simple density equation was finally applied to correlate the measured density of the (tetra-n-butyl ammonium bromide + water) system.

  13. Configuration optimization of series flow double-effect water-lithium bromide absorption refrigeration systems by cost minimization

    DEFF Research Database (Denmark)

    Mussati, Sergio F.; Cignitti, Stefano; Mansouri, Seyed Soheil

    2018-01-01

    An optimal process configuration for double-effect water-lithium bromide absorption refrigeration systems with series flow – where the solution is first passed through the high-temperature generator – is obtained by minimization of the total annual cost for a required cooling capacity. To this end......) takes place entirely at the high-temperature zone, and the sizes and operating conditions of the other process units change accordingly in order to meet the problem specification with the minimal total annual cost. This new configuration was obtained for wide ranges of the cooling capacity (150–450 k.......9%, respectively. Most importantly, the obtained optimal solution eliminates the low-temperature solution heat exchanger from the conventional configuration, rendering a new process configuration. The energy integration between the weak and strong lithium bromide solutions (cold and hot streams, respectively...

  14. Liquid helium

    CERN Document Server

    Atkins, K R

    1959-01-01

    Originally published in 1959 as part of the Cambridge Monographs on Physics series, this book addresses liquid helium from the dual perspectives of statistical mechanics and hydrodynamics. Atkins looks at both Helium Three and Helium Four, as well as the properties of a combination of the two isotopes. This book will be of value to anyone with an interest in the history of science and the study of one of the universe's most fundamental elements.

  15. Mitochondrial nucleoid clusters protect newly synthesized mtDNA during Doxorubicin- and Ethidium Bromide-induced mitochondrial stress

    Czech Academy of Sciences Publication Activity Database

    Alán, Lukáš; Špaček, Tomáš; Pajuelo-Reguera, David; Jabůrek, Martin; Ježek, Petr

    2016-01-01

    Roč. 302, Jul 1 (2016), s. 31-40 ISSN 0041-008X R&D Projects: GA ČR(CZ) GAP305/12/1247; GA MŠk(CZ) LQ1604; GA MŠk(CZ) ED1.1.00/02.0109 Institutional support: RVO:67985823 Keywords : Doxorubicin * Ethidium Bromide * nucleoid clusters * mitochondrial DNA stress * mitochondrial transcription factor A Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 3.791, year: 2016

  16. Density and surface tension of high-temperature stratifying mixtures of alkali metal bromides and lithium fluoride

    International Nuclear Information System (INIS)

    Rukavishnikova, I.V.; Lokett, V.N.; Burukhin, A.S.; Stepanov, V.P.

    2006-01-01

    The density and interphase tension of molten mixtures of lithium fluoride with potassium, rubidium, and cesium bromides were measured over the temperature range 1120-1320 K in the region of limited mutual solubility by the hydrostatic weighing and meniscus weight methods. The dependences of properties on the size ratio between the mixed ions were determined. The critical order parameters for systems with the predominantly ionic character of interparticle interactions were estimated [ru

  17. Bis(2,2'-bipyridyl-κN,N')(carbonato-κO,O')cobalt(III) bromide trihydrate.

    Science.gov (United States)

    Ma, Peng-Tao; Wang, Yu-Xia; Zhang, Guo-Qian; Li, Ming-Xue

    2007-12-06

    The title complex, [Co(CO(3))(C(10)H(8)N(2))(2)]Br·3H(2)O, is isostructural with the chloride analogue. The six-coordinated octahedral [Co(2,2'-bipy)(2)CO(3)](+) cation (2,2'-bipy is 2,2'-bipyrid-yl), bromide ion and water mol-ecules are linked together via O-H⋯Br and O-H⋯O hydrogen bonds, generating a one-dimensional chain.

  18. THE VALUE OF THE COMPOUND DRUGS FORMOTEROL AND IPRATROPIUM BROMIDE IN COMPLEX TREATMENT OF CHRONIC NONSPECIFIC LUNG DISEASES IN CHILDREN

    Directory of Open Access Journals (Sweden)

    O.I. Simonova

    2006-01-01

    Full Text Available The complex mechanism of development of bronchoobstructive bronchitis in chronic nonspecific lung diseases in children and its effective therapy with the compound bronchodilator berodual are discussed. Berodual comprises b2-adrenoreceptor agonist — fenoterol and anticholinergic drug — ipatropium bromide, that amplify bronchodilatory action of each other. Indications, contraindication and intake peculiarities are illustrated.Key words: chronic nonspecific lung diseases, bronchoob structive syndrome, bronchodilators, children.

  19. Palladium-Catalyzed Heck Coupling Reaction of Aryl Bromides in Aqueous Media Using Tetrahydropyrimidinium Salts as Carbene Ligands

    Directory of Open Access Journals (Sweden)

    İsmail Özdemir

    2010-01-01

    Full Text Available An efficient and stereoselective catalytic system for the Heck cross coupling reaction using novel 1,3-dialkyl-3,4,5,6-tetrahydropyrimidinium salts (1, LHX and Pd(OAc2 loading has been reported. The palladium complexes derived from the salts 1a-f prepared in situ exhibit good catalytic activity in the Heck coupling reaction of aryl bromides under mild conditions.

  20. Evaluating equilibrium and non-equilibrium transport of bromide and isoproturon in disturbed and undisturbed soil columns

    Science.gov (United States)

    Dousset, S.; Thevenot, M.; Pot, V.; Šimunek, J.; Andreux, F.

    2007-12-01

    In this study, displacement experiments of isoproturon were conducted in disturbed and undisturbed columns of a silty clay loam soil under similar rainfall intensities. Solute transport occurred under saturated conditions in the undisturbed soil and under unsaturated conditions in the sieved soil because of a greater bulk density of the compacted undisturbed soil compared to the sieved soil. The objective of this work was to determine transport characteristics of isoproturon relative to bromide tracer. Triplicate column experiments were performed with sieved (structure partially destroyed to simulate conventional tillage) and undisturbed (structure preserved) soils. Bromide experimental breakthrough curves were analyzed using convective-dispersive and dual-permeability (DP) models (HYDRUS-1D). Isoproturon breakthrough curves (BTCs) were analyzed using the DP model that considered either chemical equilibrium or non-equilibrium transport. The DP model described the bromide elution curves of the sieved soil columns well, whereas it overestimated the tailing of the bromide BTCs of the undisturbed soil columns. A higher degree of physical non-equilibrium was found in the undisturbed soil, where 56% of total water was contained in the slow-flow matrix, compared to 26% in the sieved soil. Isoproturon BTCs were best described in both sieved and undisturbed soil columns using the DP model combined with the chemical non-equilibrium. Higher degradation rates were obtained in the transport experiments than in batch studies, for both soils. This was likely caused by hysteresis in sorption of isoproturon. However, it cannot be ruled out that higher degradation rates were due, at least in part, to the adopted first-order model. Results showed that for similar rainfall intensity, physical and chemical non-equilibrium were greater in the saturated undisturbed soil than in the unsaturated sieved soil. Results also suggested faster transport of isoproturon in the undisturbed soil due

  1. Propargyl organometallic compounds. II. Alkylation of sodium derivatives of 1-alkyl-1-aryl-2-alkynes in liquid ammonia

    International Nuclear Information System (INIS)

    Libman, N.M.; Sevryukov, Yu.P.

    1987-01-01

    In most cases the alkylation of the sodium derivatives of 1-phenyl-1-alkyl-2-alkynes by methyl, ethyl, isopropyl, and tert-butyl bromides in liquid ammonia takes place preferentially at the sp 2 -hybridized carbon atom, and this leads to the formation of the corresponding acetylenes, The regioselectivity of the reaction is explained by the greater softness of the trigonal atom of the ambient propargyl anion and its smaller screening by the solvate shell compared with the diagonal atom

  2. Effect of phytosanitary irradiation and methyl bromide fumigation on the physical, sensory, and microbiological quality of blueberries and sweet cherries.

    Science.gov (United States)

    Thang, Karen; Au, Kimberlee; Rakovski, Cyril; Prakash, Anuradha

    2016-10-01

    The objective of this study was to determine whether irradiation could serve as a suitable phytosanitary treatment alternative to methyl bromide (MB) fumigation for blueberries and sweet cherry and also to determine the effect of phytosanitary irradiation treatment on survival of Salmonella spp. and Listeria monocytogenes on these fruit. 'Bluecrop' blueberries (Vaccinium corymbosum) and 'Sweetheart' cherries (Prunus avium) were irradiated at 0.4 kGy or fumigated with methyl bromide and evaluated for quality attributes during storage. Irradiation caused an immediate decrease in firmness of both fruit without further significant change during storage. Fumigated fruit, in contrast, softened by 11-14% during storage. Irradiation did not adversely affect blueberry and cherry shelf-life. MB fumigation did not impact blueberry and cherry quality attributes initially; however, fumigated fruit exhibited greater damage and mold growth than the control and irradiated samples during storage. Irradiation at 400 Gy resulted in a ∼1 log CFU g(-1) reduction in Salmonella spp. and Listeria monocytogenes counts, indicating that this treatment cannot significantly enhance safety. This study indicates that irradiation at a target dose of 0.4 kGy for phytosanitary treatment does not negatively impact blueberry and cherry quality and can serve as an alternative to methyl bromide fumigation. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  3. Delivery of albuterol and ipratropium bromide from two nebulizer systems in chronic stable asthma. Efficacy and pulmonary deposition

    International Nuclear Information System (INIS)

    Johnson, M.A.; Newman, S.P.; Bloom, R.; Talaee, N.; Clarke, S.W.

    1989-01-01

    Bronchodilator responses to both nebulized albuterol (salbutamol) and ipratropium bromide and aerosol delivery to the tracheobronchial tree have been assessed in eight patients with chronic stable asthma (mean baseline FEV1, 50 percent; reversibility greater than 20 percent). Two commercially available nebulizer systems were used, namely, a Turret nebulizer operated at a compressed gas flow rate of 12 L/min (droplet MMD, 3.3 mu) and an Inspiron nebulizer driven at 6 L/min (MMD, 7.7 mu). Albuterol was given as doses of 250 micrograms, 250 micrograms, 500 micrograms, and 1,000 micrograms (cumulative dose, 2 mg) and ipratropium bromide as doses of 50 micrograms, 50 micrograms, 100 micrograms, and 200 micrograms (cumulative dose, 400 micrograms) at intervals of 35 minutes. For albuterol, bronchodilatation was significantly (p less than 0.05) greater at all dosage levels with the Turret. For ipratropium, bronchodilatation was similar for both nebulizers. Measurements of aerosol deposition using 99m Tc-labelled pentetic acid (diethylenetriamine pentaacetic acid; DTPA) showed that 9.1 +/- 1.1 percent and 2.7 +/- 0.2 percent of the dose reached the lungs during nebulization to dryness for Turret and Inspiron, respectively (p less than 0.01); distribution within the lungs was similar for the two aerosols. Selection of nebulizer apparatus can influence delivery of aerosol and subsequent bronchodilator response to albuterol in patients with chronic stable asthma but is less important for aerosol delivery of ipratropium bromide in these patients

  4. Elastic silicone encapsulation of n-hexadecyl bromide by microfluidic approach as novel microencapsulated phase change materials

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Zhenjin [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China); School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Su, Lin; Li, Jing; Yang, Ruizhuang; Zhang, Zhanwen; Liu, Meifang; Li, Jie [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China); Li, Bo, E-mail: LB6711@126.com [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China)

    2014-08-20

    Highlights: • n-Hexadecyl bromide was encapsuled in elastic silicone shell. • The surfaces of microcapsules were smooth and the cross sections were compact. • Latent heat of microcapsules was 76.35 J g{sup −1}. • The microencapsulation ratio was 49 wt.%. • The microcapsules had good thermal stability. - Abstract: The elastic silicone/n-hexadecyl bromide microcapsules were prepared as novel microencapsulated phase change materials by microfluidic approach with the co-flowing channels, where the double oil1-in-oil2-in-water (O1/O2/W) droplets with a core–shell geometry were fabricated. The thermal characterizations of the microcapsules were investigated using differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). The DSC results showed that the microcapsules had good energy storage capacity with melting and freezing enthalpies 76.35 J g{sup −1} and 78.67 J g{sup −1}, respectively. The TGA investigation showed that the microcapsules had good thermal stability. The surfaces of microcapsules were smooth and the cross sections were compact from the results of optical microscope and scanning electron microscopy (SEM). Optical microscope showed that the silicone shell can provide expansion place due to its elastic property. Therefore, the silicone/n-hexadecyl bromide microcapsules showed good potential as thermal regulating textile and thermal insulation materials.

  5. Elastic silicone encapsulation of n-hexadecyl bromide by microfluidic approach as novel microencapsulated phase change materials

    International Nuclear Information System (INIS)

    Fu, Zhenjin; Su, Lin; Li, Jing; Yang, Ruizhuang; Zhang, Zhanwen; Liu, Meifang; Li, Jie; Li, Bo

    2014-01-01

    Highlights: • n-Hexadecyl bromide was encapsuled in elastic silicone shell. • The surfaces of microcapsules were smooth and the cross sections were compact. • Latent heat of microcapsules was 76.35 J g −1 . • The microencapsulation ratio was 49 wt.%. • The microcapsules had good thermal stability. - Abstract: The elastic silicone/n-hexadecyl bromide microcapsules were prepared as novel microencapsulated phase change materials by microfluidic approach with the co-flowing channels, where the double oil1-in-oil2-in-water (O1/O2/W) droplets with a core–shell geometry were fabricated. The thermal characterizations of the microcapsules were investigated using differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). The DSC results showed that the microcapsules had good energy storage capacity with melting and freezing enthalpies 76.35 J g −1 and 78.67 J g −1 , respectively. The TGA investigation showed that the microcapsules had good thermal stability. The surfaces of microcapsules were smooth and the cross sections were compact from the results of optical microscope and scanning electron microscopy (SEM). Optical microscope showed that the silicone shell can provide expansion place due to its elastic property. Therefore, the silicone/n-hexadecyl bromide microcapsules showed good potential as thermal regulating textile and thermal insulation materials

  6. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks, More than 8 hours, 10 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  7. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, More than 8 Hours, 25 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  8. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks , 8 Hours or Less, 25 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  9. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, 8 Hours or Less, 25 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  10. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, 8 Hours or Less, 50 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  11. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, More than 8 Hours, 10 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  12. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, More than 8 Hours, 50 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  13. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, More than 8 Hours, 5 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  14. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, 8 Hours or Less, 10 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  15. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks, 8 Hours or Less, 50 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  16. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks, More than 8 hours, 50 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  17. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks , 8 Hours or Less, 5 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  18. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks, More than 8 hours, 25 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  19. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks , 8 Hours or Less, 10 Foot Stack Height

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  20. Novel amphiphilic polymeric ionic liquid-solid phase micro-extraction membrane for the preconcentration of aniline as degradation product of azo dye Orange G under sonication by liquid chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Cai, Mei-Qiang; Wei, Xiao-Qing; Du, Chun-Hui; Ma, Xu-Ming; Jin, Mi-Cong

    2014-07-04

    A novel amphiphilic polymeric ionic liquid membrane containing a hydrophilic bromide anion and a hydrophobic carbonyl group was synthesized in dimethylformamide (DMF) systems using the ionic liquid 1-butyl-3-vinylimidazolium bromide (BVImBr) and the methylmethacrylate (MMA) as monomers. The prepared amphiphilic ploy-methylmethacrylate-1-butyl-3-vinylimidazolium bromide (MMA-BVImBr) was characterized by a scanning electron microscope and an infrared spectrum instrument. The results of solid-phase micro-extraction membrane (SPMM) experiments showed that the adsorption capacity of membrane was about 0.76μgμg(-1) for aniline. Based on this, a sensitive method for the determination of trace aniline, as a degradation product of azo dye Orange G under sonication, was developed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The calibration curve showed a good linearity ranging from 0.5 to 10.0μgL(-1) with a correlation coefficient value of 0.9998. The limit of quantification was 0.5μgL(-1). The recoveries ranged from 90.6% to 96.1%. The intra- and inter-day relative standard deviations were less than 8.3% and 10.9%. The developed SPMM-LC-MS/MS method was used successfully for preconcentration of trace aniline produced during the sonication of Orange G solution. Copyright © 2014 Elsevier B.V. All rights reserved.

  1. Electrochemical Study of Bromide in the Presence of 1,3-Indandione. Application to the Electrochemical Synthesis of Bromo Derivatives of 1,3-Indandione

    OpenAIRE

    Nematollahi, D.; Akaberi, N.

    2001-01-01

    The electrochemical oxidation of bromide in the presence of 1,3-indandione (1) in water/acetic acid and methanol/acetic acid mixtures has been studied by cyclic voltammetry and controlled-potential coulometry. The results indicate the participation of 1,3-indandione in the bromination reaction. On the basis of the electroanalytical and preparative results a reaction mechanism including electron transfer, chemical reaction and regeneration of bromide was discussed. The electrochemical synthesi...

  2. Physicochemical and in vitro deposition properties of salbutamol sulphate/ipratropium bromide and salbutamol sulphate/excipient spray dried mixtures for use in dry powder inhalers.

    Science.gov (United States)

    Corrigan, Deirdre O; Corrigan, Owen I; Healy, Anne Marie

    2006-09-28

    The physicochemical and aerodynamic properties of spray dried powders of the drug/drug mixture salbutamol sulphate/ipratropium bromide were investigated. The in vitro deposition properties of spray dried salbutamol sulphate and the spray dried drug/excipient mixtures salbutamol sulphate/lactose and salbutamol sulphate/PEG were also determined. Spray drying ipratropium bromide monohydrate resulted in a crystalline material from both aqueous and ethanolic solution. The product spray dried from aqueous solution consisted mainly of ipratropium bromide anhydrous. There was evidence of the presence of another polymorphic form of ipratropium bromide. When spray dried from ethanolic solution the physicochemical characterisation suggested the presence of an ipratropium bromide solvate with some anhydrous ipratropium bromide. Co-spray drying salbutamol sulphate with ipratropium bromide resulted in amorphous composites, regardless of solvent used. Particles were spherical and of a size suitable for inhalation. Twin impinger studies showed an increase in the fine particle fraction (FPF) of spray dried salbutamol sulphate compared to micronised salbutamol sulphate. Co-spray dried salbutamol sulphate:ipratropium bromide 10:1 and 5:1 systems also showed an increase in FPF compared to micronised salbutamol sulphate. Most co-spray dried salbutamol sulphate/excipient systems investigated demonstrated FPFs greater than that of micronised drug alone. The exceptions to this were systems containing PEG 4000 20% or PEG 20,000 40% both of which had FPFs not significantly different from micronised salbutamol sulphate. These two systems were crystalline unlike most of the other spray dried composites examined which were amorphous in nature.

  3. A copper-mediated reverse aromatic Finkelstein reaction in ionic liquid

    Directory of Open Access Journals (Sweden)

    Anh T.H. Nguyen

    2018-03-01

    Full Text Available We have developed a general method for reverse aromatic Finkelstein reactions. Good reaction yields were obtained when aryl iodides or aryl bromides were treated with copper halide salts as promoters in a 1-butyl-3-methylimidazolium bromide ([BMIM]Br ionic liquid (IL solvent at 140 °C for 8 h. Preliminary investigation supported that the copper salts were also the halide sources in halogen exchange reactions. The optimized conditions are applicable to a variety of substrates and have excellent functional group tolerance. Additionally, the [BMIM]Br solvent showed good stability for at least 10 consecutive runs. Results indicated that the [BMIM]Br solvent was recyclable for reverse aromatic Finkelstein reactions.

  4. Liquid electrode

    Science.gov (United States)

    Ekechukwu, A.A.

    1994-07-05

    A dropping electrolyte electrode is described for use in electrochemical analysis of non-polar sample solutions, such as benzene or cyclohexane. The liquid electrode, preferably an aqueous salt solution immiscible in the sample solution, is introduced into the solution in dropwise fashion from a capillary. The electrolyte is introduced at a known rate, thus, the droplets each have the same volume and surface area. The electrode is used in making standard electrochemical measurements in order to determine properties of non-polar sample solutions. 2 figures.

  5. Liquid diode

    International Nuclear Information System (INIS)

    1976-01-01

    The liquid diode is designed for a flowmeter chamber which has an inlet and an outlet duct, and a flow chamber with a cross-section which is greater than inlet. In the space between the inlet and outlet are two screens with a number of spheres, which may be of different sizes and weights. The screen on the inlet side is smaller than that at the outlet, so that the spheres are able to block the inlet under reverse flow conditions, but do not block the outlet. The system functions as a non-return valve. (G.C.)

  6. Combination of selected enzymes with cetyltrimethylammonium bromide in biofilm inactivation, removal and regrowth

    KAUST Repository

    Araujo, Paula Alexandra Da Silva; Machado, Idalina; Meireles, Ana; Leiknes, TorOve; Mergulhã o, Filipe; Melo, Luí s F.; Simõ es, Manuel

    2017-01-01

    Enzymes are considered an innovative and environmentally friendly approach for biofilm control due to their lytic and dispersal activities. In this study, four enzymes (β-glucanase, α-amylase, lipase and protease) were tested separately and in combination with the quaternary ammonium compound cetyltrimethylammonium bromide (CTAB) to control flow-generated biofilms of Pseudomonas fluorescens. The four enzymes caused modest reduction of biofilm colony forming units (CFU). Protease, β-glucanase and α-amylase also caused modest biofilm removal. CTAB combined with either β-glucanase or α-amylase increased biofilm removal. Its combination with either β-glucanase or protease increased CFU reduction. However, CTAB−protease combination was antagonist in biofilm removal. Long-term effects in biofilm mass reduction were observed after protease exposure. In contrast, biofilms treated with β-glucanase were able to regrowth significantly after exposure. Moreover, short-term respirometry tests with planktonic cells were performed to understand the effects of enzymes and their combination with CTAB on P. fluorescens viability. Protease and lipase demonstrated antimicrobial action, while α-amylase increased bacterial metabolic activity. The combination of CTAB with either protease or α-amylase was antagonistic, decreasing the antimicrobial action of CTAB. The overall results demonstrate a modest effect of the selected enzymes in biofilm control, either when applied alone or each one in combination with CTAB. Total biofilm removal or CFU reduction was not achieved and, in some cases, the use of enzymes antagonized the effects of CTAB. The results also propose that complementary tests, to characterize biofilm integrity and microbial viability, are required when someone is trying to assess the role of novel biocide - enzyme mixtures for effective biofilm control.

  7. Spectroscopic study on the interaction of Bacillus subtilis α-amylase with cetyltrimethylammonium bromide

    International Nuclear Information System (INIS)

    Omidyan, R.; Kazemi, S.H.; Bordbar, A.K.; Zaynalpour, S.

    2011-01-01

    The interaction between α-amylase from Bacillus subtilis and cetyltrimethylammonium bromide (CTAB) has been investigated at various temperature conditions using fluorescence and circular dichroism (CD) spectroscopic methods. Fluorescence data revealed that the fluorescence quenching of α-amylase by CTAB is the result of complex formation between CTAB and α-amylase. The thermodynamic analysis on the binding interaction data shows that the interactions are strongly exothermic (ΔH o =-17.92 kJ mol -1 ) accompanied with increase in entropy (ΔS o between 109 to 135 J mol -1 K -1 ). Thus the binding of CTAB to α-amylase is both enthalpic and entropic driven, which represent the predominate role of both electrostatic and hydrophobic interactions in complex formation process. The values of 2.17x10 -3 M -1 and 1.30 have been obtained from associative binding constant (K a ) and stoichiometry of binding number (n), from analysis of fluorescence data, respectively. Circular dichroism spectra showed the substantial conformational changes in secondary structure of α-amylase due to binding of CTAB, which represents the complete destruction of both secondary and tertiary structure of α-amylase by CTAB. - Research highlights: → The Fluorescence quenching effect of α-amylase by CTAB is a consequence of formation α-amylase-CTAB complex. → The α-helical analyzing from the CD spectra in the various concentration of CTAB shows strongly deformation of α-amylase. → Thermodynamic analysis of quenching verify that the interactions are both enthalpy and entropic driven.

  8. Ionization and dissociation dynamics of vinyl bromide probed by femtosecond extreme ultraviolet transient absorption spectroscopy

    International Nuclear Information System (INIS)

    Lin, Ming-Fu; Neumark, Daniel M.; Gessner, Oliver; Leone, Stephen R.

    2014-01-01

    Strong-field induced ionization and dissociation dynamics of vinyl bromide, CH 2 =CHBr, are probed using femtosecond extreme ultraviolet (XUV) transient absorption spectroscopy. Strong-field ionization is initiated with an intense femtosecond, near infrared (NIR, 775 nm) laser field. Femtosecond XUV pulses covering the photon energy range of 50-72 eV probe the subsequent dynamics by measuring the time-dependent spectroscopic features associated with transitions of the Br (3d) inner-shell electrons to vacancies in molecular and atomic valence orbitals. Spectral signatures are observed for the depletion of neutral C 2 H 3 Br, the formation of C 2 H 3 Br + ions in their ground (X ~ ) and first excited (A ~ ) states, the production of C 2 H 3 Br ++ ions, and the appearance of neutral Br ( 2 P 3/2 ) atoms by dissociative ionization. The formation of free Br ( 2 P 3/2 ) atoms occurs on a timescale of 330 ± 150 fs. The ionic A ~ state exhibits a time-dependent XUV absorption energy shift of ∼0.4 eV within the time window of the atomic Br formation. The yield of Br atoms correlates with the yield of parent ions in the A ~ state as a function of NIR peak intensity. The observations suggest that a fraction of vibrationally excited C 2 H 3 Br + (A ~ ) ions undergoes intramolecular vibrational energy redistribution followed by the C–Br bond dissociation. The C 2 H 3 Br + (X ~ ) products and the majority of the C 2 H 3 Br ++ ions are relatively stable due to a deeper potential well and a high dissociation barrier, respectively. The results offer powerful new insights about orbital-specific electronic processes in high field ionization, coupled vibrational relaxation and dissociation dynamics, and the correlation of valence hole-state location and dissociation in polyatomic molecules, all probed simultaneously by ultrafast table-top XUV spectroscopy

  9. Comparison of Freezing and Hydrate Formation Methods in Removing Chloride and Bromide Ions from Brine

    Directory of Open Access Journals (Sweden)

    Marzieh Fattahi

    2018-01-01

    Full Text Available The growing population and enhanced industrial activities coupled with limitations on freshwater availability have led to efforts to desalinate salt water from the seas. Membrane and thermal technologies are the two commonly used for this purpose. In this study, the direct freezing and hydrate formation techniques were used for salt water desalination. Materials and Methods: Distilled water, sodium chloride, and sodium bromide were used as raw materials in the experiments. The experimental setup included a stationary reactor with two coaxial cylinders, in which ice crystals were deposited outside the cool inner cylinder to increase the salt concentration in the residual brine. An electrical conductivity instrument was used to measure sal removal. Results: Salt removal was shown to decrease with increasing salt concentration in the direct freeze method. A different trend was, however, observed in the hydrate formation method; salt removal was negligible at low concentrations in this method but increased at high concentrations before a constant value was reached. Overall, the hydrate formation recorded a higher salt removal efficiency than the other method. To investigate the effect of anion size on salt removal efficiency, experiments were carried out using NaCl and NaBr, which have the same cation but different anion sizes. Result showed that removal efficiency increased with increasing anion size. Conclusion: It was found that increasing ion radius leads to the lower likelihood of ion presence in the crystal lattice, thereby reducing salt removal efficiency. On the other hand, low concentrations of salt serve as site for the generation of cores, which naturally serve as removal accelerators.

  10. Spectroscopic study on the interaction of Bacillus subtilis {alpha}-amylase with cetyltrimethylammonium bromide

    Energy Technology Data Exchange (ETDEWEB)

    Omidyan, R., E-mail: r.omidyan@sci.ui.ac.i [Department of Chemistry, University of Isfahan, Isfahan 81746-73441 (Iran, Islamic Republic of); Department of Chemistry, Institute for Advanced Studies in Basic Sciences (IASBS), Zanjan 45137-66731 (Iran, Islamic Republic of); Kazemi, S.H. [Department of Chemistry, Institute for Advanced Studies in Basic Sciences (IASBS), Zanjan 45137-66731 (Iran, Islamic Republic of); Bordbar, A.K. [Department of Chemistry, University of Isfahan, Isfahan 81746-73441 (Iran, Islamic Republic of); Zaynalpour, S. [Department of Chemistry, Institute for Advanced Studies in Basic Sciences (IASBS), Zanjan 45137-66731 (Iran, Islamic Republic of)

    2011-06-15

    The interaction between {alpha}-amylase from Bacillus subtilis and cetyltrimethylammonium bromide (CTAB) has been investigated at various temperature conditions using fluorescence and circular dichroism (CD) spectroscopic methods. Fluorescence data revealed that the fluorescence quenching of {alpha}-amylase by CTAB is the result of complex formation between CTAB and {alpha}-amylase. The thermodynamic analysis on the binding interaction data shows that the interactions are strongly exothermic ({Delta}H{sup o}=-17.92 kJ mol{sup -1}) accompanied with increase in entropy ({Delta}S{sup o} between 109 to 135 J mol{sup -1} K{sup -1}). Thus the binding of CTAB to {alpha}-amylase is both enthalpic and entropic driven, which represent the predominate role of both electrostatic and hydrophobic interactions in complex formation process. The values of 2.17x10{sup -3} M{sup -1} and 1.30 have been obtained from associative binding constant (K{sub a}) and stoichiometry of binding number (n), from analysis of fluorescence data, respectively. Circular dichroism spectra showed the substantial conformational changes in secondary structure of {alpha}-amylase due to binding of CTAB, which represents the complete destruction of both secondary and tertiary structure of {alpha}-amylase by CTAB. - Research highlights: {yields} The Fluorescence quenching effect of {alpha}-amylase by CTAB is a consequence of formation {alpha}-amylase-CTAB complex. {yields} The {alpha}-helical analyzing from the CD spectra in the various concentration of CTAB shows strongly deformation of {alpha}-amylase. {yields} Thermodynamic analysis of quenching verify that the interactions are both enthalpy and entropic driven.

  11. Extraction spectrophotometric determination of rare earth with trioctylethylammonium bromide and Xylenol Orange

    International Nuclear Information System (INIS)

    Shijo, Yoshio

    1976-01-01

    A spectrophotometric method of determination of the rare earth was studied by the solvent extraction of rare earth-Xylenol Orange chelate into xylene solution of trioctylethylammonium bromide(TOEA). The rare earth-XO-TOEA complexes are extracted into aromatic hydrocarbons such as benzene, toluene, and xylene, but not into polar solvents such as n-butanol ethylacetate, methylisobutylketone, and nitrobenzene. The optimum pH range for the extraction were 6.3 -- 6.7, 6.3 -- 6.5, 5.8 -- 6.9, 5.7 -- 6.9, and 5.5 -- 6.8 for lanthanum, praseodymium, cerium, gadolinium, and dysprosium, respectively. The absorption maximum of the complexes extracted into xylene were found at 605 nm for lanthanum, praseodymium, and cerium, 596 nm for gadolinium, and 590 nm for dysprosium. Beer's law held for about 0 -- 4.5 μg of rare earth per 5 ml of xylene. The molar absorptivity of the extracted species were 1.53x10 5 , 1.42x10 5 , 1.35x10 5 , 8.5x10 4 , 8.2x10 4 cm -1 mol -1 l for lanthanum, praseodymium, cerium, gadolinium, and dysprosium, respectively. The composition of the ternary complexes were estimated to be M:XO:TOEA=1:1:2 for gadolinium and dysprosium, whereas 1:2:n for lanthanum, praseodymium and cerium. Combination ratio n of TOEA to metal-XO chelates in the latters could not be estimated by the commonly available methods. Thorium, vanadium, uranium, bismuth, aluminum, zirconium, chromium, nitrate, perchlorate and iodide interfered when triethylenetetramine and 1,10-phenanthroline were added as masking agent. (auth.)

  12. Nutrient removal by Chlorella vulgaris F1068 under cetyltrimethyl ammonium bromide induced hormesis.

    Science.gov (United States)

    Zhou, Qiongzhi; Li, Feng; Ge, Fei; Liu, Na; Kuang, Yangduo

    2016-10-01

    Toxicants are generally harmful to biotechnology in wastewater treatment. However, trace toxicant can induce microbial hormesis, but to date, it is still unknown how this phenomenon affects nutrient removal during municipal wastewater treatment process. Therefore, this study focused on the effects of hormesis induced by cetyltrimethyl ammonium bromide (CTAB), a representative quaternary ammonium cationic surfactant, on nutrient removal by Chlorella vulgaris F1068. Results showed that when the concentration of CTAB was less than 10 ng/L, the cellular components chlorophyll a, proteins, polysaccharides, and total lipids increased by 10.11, 58.17, 38.78, and 11.87 %, respectively, and some enzymes in nutrient metabolism of algal cells, such as glutamine synthetase (GS), acid phosphatase (ACP), H(+)-ATPase, and esterase, were also enhanced. As a result, the removal efficiencies of ammonia nitrogen (NH4 (+)) and total phosphorus (TP) increased by 14.66 and 8.51 %, respectively, compared to the control during a 7-day test period. The underlying mechanism was mainly due to an enhanced photosynthetic activity of C. vulgaris F1068 indicated by the increase in chlorophyll fluorescence parameters (the value of Fv/Fm, ΦII, Fv/Fo, and rETR increased by 12.99, 7.56, 25.59, and 8.11 %, respectively) and adenylate energy charge (AEC) (from 0.68 to 0.72). These results suggest that hormesis induced by trace toxicants could enhance the nutrient removal, which would be further considered in the design of municipal wastewater treatment processes. Graphical abstract The schematic mechanism of C. vulgaris F1068 under CTAB induced hormesis. Green arrows ( ) represent the increase and the red arrow ( ) represents the decrease.

  13. Application of artificial neural network in 3D imaging with lanthanum bromide calorimeter

    Science.gov (United States)

    Gostojic, A.; Tatischeff, V.; Kiener, J.; Hamadache, C.; Karkour, N.; Linget, D.; Grave, X.; Gibelin, L.; Travers, B.; Blin, S.; Barrillon, P.

    2015-07-01

    Gamma-ray astronomy in the energy range from 0.1 up to 100 MeV holds many understudied questions connected with e.g. stellar nucleosynthesis, the active Sun, neutron stars and black holes. To access the physics behind, a significant improvement in detection sensitivity is needed compared to previous missions, e.g. CGRO and INTEGRAL. One of the promising concepts for a future gamma-ray mission is an Advanced Compton Telescope. Under the project of creating a prototype of such instrument, we study the perspectives of using a novel inorganic scintillator as a calorimeter part. Modern inorganic crystal or ceramics scintillators are constantly improving on qualities such as energy resolution and radiation hardness, and this makes them a smart choice for a new space-borne telescope. At CSNSM Orsay, we have assembled a detection module from a 5 × 5cm2 area and 1 cm thick, cerium-doped lanthanum (III) bromide (LaBr3:Ce) inorganic scintillator coupled to a 64 channel multi-anode photomultiplier. The readout of the PMT signals is carried out with the ASIC MAROC, used previously for the luminometer of the ATLAS detector (CERN). Characterization, thorough measurements with various radioactive sources, as well as, single photoelectron detection have been done. Furthermore, we made a comparison of measurements with a detailed GEANT4-based simulation which includes tracking of the optical photons. Finally, we have studied the 3D reconstruction of the first interaction point of incident gamma rays, utilizing a neural network algorithm. This spatial position resolution plays a crucial part in the future implementations and, together with the other measured properties, it makes our detector module very interesting for the next generation of space telescopes operating in the MeV range.

  14. White-Light Emission and Structural Distortion in New Corrugated Two-Dimensional Lead Bromide Perovskites.

    Science.gov (United States)

    Mao, Lingling; Wu, Yilei; Stoumpos, Constantinos C; Wasielewski, Michael R; Kanatzidis, Mercouri G

    2017-03-29

    Hybrid inorganic-organic perovskites are developing rapidly as high performance semiconductors. Recently, two-dimensional (2D) perovskites were found to have white-light, broadband emission in the visible range that was attributed mainly to the role of self-trapped excitons (STEs). Here, we describe three new 2D lead bromide perovskites incorporating a series of bifunctional ammonium dications as templates which also emit white light: (1) α-(DMEN)PbBr 4 (DMEN = 2-(dimethylamino)ethylamine), which adopts a unique corrugated layered structure in space group Pbca with unit cell a = 18.901(4) Å, b = 11.782(2) Å, and c = 23.680(5) Å; (2) (DMAPA)PbBr 4 (DMAPA = 3-(dimethylamino)-1-propylamine), which crystallizes in P2 1 /c with a = 10.717(2) Å, b = 11.735(2) Å, c = 12.127(2) Å, and β = 111.53(3)°; and (3) (DMABA)PbBr 4 (DMABA = 4-dimethylaminobutylamine), which adopts Aba2 with a = 41.685(8) Å, b = 23.962(5) Å, and c = 12.000(2) Å. Photoluminescence (PL) studies show a correlation between the distortion of the "PbBr 6 " octahedron in the 2D layer and the broadening of PL emission, with the most distorted structure having the broadest emission (183 nm full width at half-maximum) and longest lifetime (τ avg = 1.39 ns). The most distorted member α-(DMEN)PbBr 4 exhibits white-light emission with a color rendering index (CRI) of 73 which is similar to a fluorescent light source and correlated color temperature (CCT) of 7863 K, producing "cold" white light.

  15. Combination of selected enzymes with cetyltrimethylammonium bromide in biofilm inactivation, removal and regrowth

    KAUST Repository

    Araujo, Paula Alexandra Da Silva

    2017-03-01

    Enzymes are considered an innovative and environmentally friendly approach for biofilm control due to their lytic and dispersal activities. In this study, four enzymes (β-glucanase, α-amylase, lipase and protease) were tested separately and in combination with the quaternary ammonium compound cetyltrimethylammonium bromide (CTAB) to control flow-generated biofilms of Pseudomonas fluorescens. The four enzymes caused modest reduction of biofilm colony forming units (CFU). Protease, β-glucanase and α-amylase also caused modest biofilm removal. CTAB combined with either β-glucanase or α-amylase increased biofilm removal. Its combination with either β-glucanase or protease increased CFU reduction. However, CTAB−protease combination was antagonist in biofilm removal. Long-term effects in biofilm mass reduction were observed after protease exposure. In contrast, biofilms treated with β-glucanase were able to regrowth significantly after exposure. Moreover, short-term respirometry tests with planktonic cells were performed to understand the effects of enzymes and their combination with CTAB on P. fluorescens viability. Protease and lipase demonstrated antimicrobial action, while α-amylase increased bacterial metabolic activity. The combination of CTAB with either protease or α-amylase was antagonistic, decreasing the antimicrobial action of CTAB. The overall results demonstrate a modest effect of the selected enzymes in biofilm control, either when applied alone or each one in combination with CTAB. Total biofilm removal or CFU reduction was not achieved and, in some cases, the use of enzymes antagonized the effects of CTAB. The results also propose that complementary tests, to characterize biofilm integrity and microbial viability, are required when someone is trying to assess the role of novel biocide - enzyme mixtures for effective biofilm control.

  16. Effects of cetyltriethylammonium bromide on the replication of Bombyx mori nucleopolyhedrovirus.

    Science.gov (United States)

    Zhou, Yajing; Zhang, Zhifang; He, Jialu; Zhang, Yuanxing

    2002-05-01

    An experimental study was undertaken to quantify the effects of cetyltriethylammonium bromide (CTAB) on the replication of Bombyx mori nucleopolyhedrovirus (BmNPV) and the transcriptionalactivity of BmNPV ie-1 promoter. The results demonstrated that the budded virus (BV) titer rose about 3.7-fold by adding CTAB to the culture media up to 0.1 mu g ml(-1) in infected Bm-N cells with a wild-type BmNPV. The transient expression level of luciferase driven by BmNPV ie-1 promoter was enhanced by more than 3-fold in the presence of 0.1 mu g ml(-1) of CTAB in uninfected insect cells via a transient expression system. Contrary to the rise in BV titer, the polyhedra inside the nucleus of infected cells dropped linearly from 4.0 x 10(6) ml(-1) down to 2.1 x 10(6) ml(-1) with in a range of CTAB concentrations from 0 to 0.25 mu g ml(-1). The same trend in expression level of beta -galactosidase or phytase was given when the Bm-N cells or fifth-instar silkworm larvae infected with a recombinant BmNPV containing the beta -galactosidase or phytase reporter gene driven by the polyhedrin promoter. We deduced that CTAB appeared to affect the virus bi-phasic life cycle stages and production pathways, resulting in an enhancement in BV production and a suppression of occluded virus (OV) production and expression of foreign genes controlled by the polyhedrin promoter.

  17. Pixellated thallium bromide detectors for gamma-ray spectroscopy and imaging

    Energy Technology Data Exchange (ETDEWEB)

    Onodera, T. E-mail: tosiyuki@smail.tohtech.ac.jp; Hitomi, K.; Shoji, T.; Hiratate, Y

    2004-06-01

    Recently, pixellated semiconductor detectors exhibit high-energy resolution, which have been studied actively and fabricated from CdTe, CZT and HgI{sub 2}. Thallium bromide (TlBr) is a compound semiconductor characterized with its high atomic numbers (Tl=81, Br=35) and high density (7.56 g/cm{sup 3}). Thus, TlBr exhibits higher photon stopping power than other semiconductor materials used for radiation detector fabrication such as CdTe, CZT and HgI{sub 2}. The wide band gap of TlBr (2.68 eV) permits the detectors low-noise operation at around room temperature. Our studies made an effort to fabricate pixellated TlBr detectors had sufficient detection efficiency and good charge collection efficiency. In this study, pixellated TlBr detectors were fabricated from the crystals purified by the multipass zone-refining method and grown by the horizontal traveling molten zone (TMZ) method. The TlBr detector has a continuous cathode over one crystal surface and 3x3 pixellated anodes (0.57x0.57 mm{sup 2} each) surrounded by a guard ring on the opposite surface. The electrodes were realized by vacuum evaporation of palladium through a shadow mask. Typical thickness of the detector was 2 mm. Spectrometric performance of the TlBr detectors was tested by irradiating them with {sup 241}Am (59.5 keV), {sup 57}Co (122 keV) and {sup 137}Cs (662 keV) gamma-ray sources at temperature of -20 deg. C. Energy resolutions (FWHM) were measured to be 4.0, 6.0 and 9.7 keV for 59.5, 122 and 662 keV gamma-rays, respectively.

  18. Determination of niobium with p-arsonophenylazochromotropic acied and cetylpyridinium bromide

    International Nuclear Information System (INIS)

    Sanz-Medel, A.; Camara Rica, C.; Perez-Bustamante, J.A.

    1980-01-01

    Color stabilization and modification of the visible spectrum of the p-arsonophenylazochromotropic acid (L) and Nb(V) binary complex by the addition of surfactants has been studied in the course of a search for improved spectrophotometric methods for niobium. Addition of cationic surfactants resulted in an effective means of color stabilization and brought about a drastic improvement in the intensity of the absorption band maximum (sensitized reactions). The surfactant which gave the most intense absorption band maximum was cetylpyridinium bromide (CPAB). Spectrophotometric measurements indicate the formation of two Nb-L-CPAB ion-association ternary complexes: a complex with the stoichiometry 1:2:4 was formed in approximately 1 M HCl. The other complex had the stoichiometry 1:1:2 and formed in 2 to 4 M HCl mediums. Both ternary complexes mentioned can be applied to the spectrophotometric determination of niobium and two different analytical methods have been established: the complex formed in a 1.0 M HCl medium provides a method less selective than the complex formed in 2 to 4 M HCl. The method provided by the former complex is sensitive (epsilon = 1.87 x 10 4 L mol -1 cm -1 ), has a working range of 0.5 to 5 ppm Nb, and has a relative standard deviation of 0.5%. The complex formed in the higher acidity range provides a less sensitive method. The working range is 1 to 9 ppm and epsilon = 7.40 x 10 3 L mol -1 cm -1 . This latter method is most adequate for a selective spectrophotometric determination of niobium (relative standard deviation being 0.5%). 5 figures, 2 tables

  19. Production of hydrogen bromide and oxygen from water and bromine using a metal oxide

    International Nuclear Information System (INIS)

    Ishikawa, Hiroshi; Nakane, Masanori; Ishii, Eiichi; Uehara, Itsuki; Miyake, Yoshizo

    1978-01-01

    In order to produce hydrogen by the thermochemical water splitting cycle, the following two-step reactions have been investigated. M.O + Br 2 → M.Br 2 + 1/2O 2 (1) M.Br 2 + H 2 O → M.O + 2HBr (2) At first, indium, zinc, cobalt, manganese and nickel were picked up as suitable elements based on ΔG 0 -T diagram of the reactions. Then, each fundamental reaction was checked experimentally. In the case of cobalt, manganese and nickel, reaction (1) hardly proceeded below 900 0 C under atmospheric pressure of Br 2 . Therefore, detailed experiments were carried out on zinc and indium. In the case of zinc, the equilibrium conversion of Br 2 for reaction (1) was estimated to be 37% at 900 0 C and that of ZnBr 2 (g) for reaction (2) was estimated to be 5% at the same temperature. Also in the case of indium, both the equilibrium conversions of Br 2 and of InBr 3 (g) turned out 10% under the same conditions. As the rate of conversion was rather low, large amounts of unreacted substances should be recycled to proceed these reactions. In the hydrolysis of both ZnBr 2 and InBr 3 , the use of five and ten times larger amount of H 2 O could reduce the amounts of unreacted metal bromides to about a half and one third of the values mentioned above, respectively. Under the present conditions the two-step sub-cycle using the metal oxide is considered to be difficult to realize from technical points of view. (author)

  20. Performance characteristics of single effect lithium bromide/ water absorption chiller for small data centers

    Science.gov (United States)

    Mysore, Abhishek Arun Babu

    A medium data center consists of servers performing operations such as file sharing, collaboration and email. There are a large number of small and medium data centers across the world which consume more energy and are less efficient when compared to large data center facilities of companies such as GOOGLE, APPLE and FACEBOOK. Such companies are making their data center facilities more environmental friendly by employing renewable energy solutions such as wind and solar to power the data center or in data center cooling. This not only reduces the carbon footprint significantly but also decreases the costs incurred over a period of time. Cooling of data center play a vital role in proper functioning of the servers. It is found that cooling consumes about 50% of the total power consumed by the data center. Traditional method of cooling includes the use of mechanical compression chillers which consume lot of power and is not desirable. In order to eliminate the use of mechanical compressor chillers renewable energy resources such as solar and wind should be employed. One such technology is solar thermal cooling by means of absorption chiller which is powered by solar energy. The absorption chiller unit can be coupled with either flat plate or evacuated tube collectors in order to achieve the required inlet temperature for the generator of the absorption chiller unit. In this study a modular data center is considered having a cooling load requirement of 23kw. The performance characteristics of a single stage Lithium Bromide/ water refrigeration is presented in this study considering the cooling load of 23kw. Performance characteristics of each of the 4 heat exchangers within the unit is discussed which helps in customizing the unit according to the users' specific needs. This analysis helps in studying the importance of different properties such as the effect of inlet temperatures of hot water for generator, inlet temperatures of cooling water for absorber and

  1. From Funding Liquidity to Market Liquidity

    DEFF Research Database (Denmark)

    Dick-Nielsen, Jens; Lund, Jesper; Gyntelberg, Jacob

    This paper shows empirically that funding liquidity drives market liquidity. As it becomes harder to secure term funding in the money markets, liquidity deteriorates in the Danish bond market. We show that the first principal component of bond market liquidity is driven by the market makers...... for other European government bonds using MTS data. The findings suggest that regulatory bond based liquidity buffers for banks will have limited effectiveness....

  2. Lyotropic liquid crystalline phase behaviour in amphiphile-protic ionic liquid systems.

    Science.gov (United States)

    Chen, Zhengfei; Greaves, Tamar L; Fong, Celesta; Caruso, Rachel A; Drummond, Calum J

    2012-03-21

    Approximate partial phase diagrams for nine amphiphile-protic ionic liquid (PIL) systems have been determined by synchrotron source small angle X-ray scattering, differential scanning calorimetry and cross polarised optical microscopy. The binary phase diagrams of some common cationic (hexadecyltrimethyl ammonium chloride, CTAC, and hexadecylpyridinium bromide, HDPB) and nonionic (polyoxyethylene (10) oleyl ether, Brij 97, and Pluronic block copolymer, P123) amphiphiles with the PILs, ethylammonium nitrate (EAN), ethanolammonium nitrate (EOAN) and diethanolammonium formate (DEOAF), have been studied. The phase diagrams were constructed for concentrations from 10 wt% to 80 wt% amphiphile, in the temperature range 25 °C to >100 °C. Lyotropic liquid crystalline phases (hexagonal, cubic and lamellar) were formed at high surfactant concentrations (typically >50 wt%), whereas at thermal stability of the phases formed by these surfactants persisted to temperatures above 100 °C. The phase behaviour of amphiphile-PIL systems was interpreted by considering the PIL cohesive energy, liquid nanoscale order, polarity and ionicity. For comparison the phase behaviour of the four amphiphiles was also studied in water.

  3. Liquid crystalline epoxy nanocomposite material for dental application.

    Science.gov (United States)

    Tai, Yun-Yuan; Hsu, Sheng-Hao; Chen, Rung-Shu; Su, Wei-Fang; Chen, Min-Huey

    2015-01-01

    Novel liquid crystalline epoxy nanocomposites, which exhibit reduced polymerization shrinkage and effectively bond to tooth structures, can be applied in esthetic dentistry, including core and post systems, direct and indirect restorations, and dental brackets. The purposes of this study were to investigate the properties of liquid crystalline epoxy nanocomposites including biocompatibility, microhardness, and frictional forces of bracket-like blocks with different filler contents for further clinical applications. In this study, we evaluated liquid crystalline epoxy nanocomposite materials that exhibited various filler contents, by assessing their cell activity performance using a 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay and their microhardness with or without thermocycling. We also evaluated the frictional force between bracket-like duplicates and commercially available esthetic bracket systems using Instron 5566. The liquid crystalline epoxy nanocomposite materials showed good biocompatibility. The materials having high filler content demonstrated greater microhardness compared with commercially available bracket materials, before and after the thermocycling treatment. Thus, manufacturing processes are important to reduce frictional force experienced by orthodontic brackets. The microhardness of the bracket-like blocks made by our new material is superior to the commercially available brackets, even after thermocycling. Our results indicate that the evaluated liquid crystalline epoxy nanocomposite materials are of an appropriate quality for application in dental core and post systems and in various restorations. By applying technology to refine manufacturing processes, these new materials could also be used to fabricate esthetic brackets for orthodontic treatment. Copyright © 2014. Published by Elsevier B.V.

  4. U.S. EPA, Pesticide Product Label, METHYL BROMIDE 89.5%, 09/06/1989

    Science.gov (United States)

    2011-04-19

    ... a .. d V' • ..ut .. r.. Liquid (inh.laU .... h .... d). Do not ahlp ... ' : .~; t:~ ': . nee.allty to .n'" "0'" pt'iof to dllc .... 'OI. ... booll. . ,-·t··:, . j, .. ·· laM •• wh". ...

  5. Synthesis and characterization of new N-heterocyclic carbene ligands: 1,3-Bis(acetamide)imidazol-3-ium bromide and 3-(acetamide)-1-(3-aminopropyl)-1H-imidazol-3-ium bromide

    Science.gov (United States)

    Turkyilmaz, Murat; Uluçam, Gühergül; Aktaş, Şaban; Okan, S. Erol

    2017-05-01

    Two new pincer type N-heterocyclic carbene ligands were synthesized. The compounds were characterized by FTIR, NMR (1H, 13C) GC-MS and elemental analyses. They were also both modelled by DFT calculations as the crystal structure of 1,3-bis(acetamide)imidazol-3-ium bromide was determined by XRD which is an orthorhombic system with space group P21212. The structural analyses in gas phase were realized by comparing the experimental NMR and IR spectra with those of the theoretical calculations. In vitro biological activities of the molecules were determined and found that one of them exhibits significant cytotoxic activity.

  6. Importance of Interfacial Interactions to Access Shear Elasticity of Liquids and Understand Flow Induced Birefringence from Liquid Crystals to Worm-Like Micellar Solutions

    Directory of Open Access Journals (Sweden)

    Noirez Laurence

    2017-03-01

    Full Text Available This work points out the importance of the substrate boundary conditions to lower the dissipation in the dynamic measurement and access the closest dynamic characteristics of liquids, in particular to access the low frequency shear elasticity. The liquid/surface interface is a source of dissipation that enters and impacts the measurement. Examples of steady-state shear flows or flow birefringence are presented to highlight the non-universality of the behavior with respect to the nature of the substrate or the sheared thickness. Additionally the present development completes and extends the identification of low frequency shear elasticity made at sub-millimeter gaps in various one-component liquids to salt-free aqueous solutions (CTAB-water (Hexadecyl-TrimethylAmmonium Bromide.

  7. CdTe quantum dots functionalized with 4-amino-2,2,6,6-tetramethylpiperidine-N-oxide as luminescent nanoprobe for the sensitive recognition of bromide ion

    Energy Technology Data Exchange (ETDEWEB)

    Adegoke, Oluwasesan [Department of Chemistry, Rhodes University, Grahamstown 6140 (South Africa); Hosten, Eric; McCleland, Cedric [Department of Chemistry, Nelson Mandela Metropolitan University (South Campus), Port Elizabeth 6031 (South Africa); Nyokong, Tebello, E-mail: t.nyokong@ru.ac.za [Department of Chemistry, Rhodes University, Grahamstown 6140 (South Africa)

    2012-04-06

    Graphical abstract: A bromide ion-selective modified nanoprobe sensor based on 4-amino-2,2,6,6-tetramethylpiperidine-N-oxide (4AT)-functionalized CdTe quantum dots (QDs-4AT) showed a high selectivity and sensitivity for the determination of bromide ion using fluorescence recovery. Highlights: Black-Right-Pointing-Pointer Water soluble CdTe quantum dots interact with tetramethylpiperidine-N-oxide. Black-Right-Pointing-Pointer Quantum dots fluorescence is quenched by the radical. Black-Right-Pointing-Pointer In the presence of bromide ions the fluorescence is restored. Black-Right-Pointing-Pointer The sensor is more selective to bromine ions than other common ions. - Abstract: A novel bromide ion-selective modified nanoprobe sensor based on 4-amino-2,2,6,6-tetramethylpiperidine-N-oxide (4AT)-functionalized CdTe quantum dots (QDs-4AT) has been developed. Fluorescence quenching of the QDs by 4AT was observed. The functionalized QDs-4AT nanoprobe allowed a highly sensitive determination of bromide ion via analyte-induced change in the photoluminescence (fluorescence recovery) of the modified QDs. A detection limit of 0.6 nM of bromide ion was obtained, while the interfering effect of other inorganic cations and anions was investigated to examine the selectivity of the nanoprobe. The linear range was between 0.01 and 0.13 {mu}M. Combined fluorescence lifetime and electron paramagnetic resonance measurements confirmed electron transfer processes between bromide ion and QDs-4AT.

  8. Experimental investigation on an ammonia-water-lithium bromide absorption refrigeration system without solution pump

    International Nuclear Information System (INIS)

    Wu Tiehui; Wu Yuyuan; Yu Zhiqiang; Zhao Haichen; Wu Honglin

    2011-01-01

    Highlights: → An absorption refrigeration system with ternary solution of NH 3 -H 2 O-LiBr was set up. → Performance of the NH 3 -H 2 O-LiBr system without solution pump was firstly tested. → Generator pressure in NH 3 -H 2 O-LiBr system was lower than the one in NH 3 -H 2 O system. → The COP of the NH 3 -H 2 O-LiBr system was 51.89% larger than the NH 3 -H 2 O binary system. → The optimum mass fraction of LiBr of about 23% led to the largest COP of 0.401. -- Abstract: Experimental researches were carried out on a novel ammonia-water-lithium bromide ternary solution absorption refrigeration and air-conditioning system without solution pump and distillation equipments. The experiments were conducted by using three kinds of NH 3 -H 2 O binary solution and 17 kinds of ternary solution with difference in mass fraction of NH 3 and LiBr. The experimental results showed that the vapor pressure of the generator in the system would be lower than that of the generator in an ammonia-water absorption system. In above two situations the same ammonia mass fraction and the same solution temperature were kept. The amplitude of vapor pressure decrease of the system generator would be larger with the increase of the mass fraction of LiBr. The maximum amplitude of decrease would be of 50%. With the increase of the mass fraction of LiBr, the coefficient of performance (COP) of the system would be increased initially, and then decreased later when the mass fraction of LiBr exceeded a certain value. This value was about 23% for the solution with ammonia mass fraction of 50% and 55%, and about 30% for the solution with ammonia mass fraction of 60%. Compared with the ammonia-water system, the COP of the ternary solution system with the same mass fraction of ammonia would increase up to 30%. With the ammonia mass fraction of 60% and LiBr mass fraction of 30% applied, the COP of the ternary solution system was increased up to 0.401. It was 51.89% higher than that when binary

  9. Tiotropium bromide in the routine care of GOLD stage II COPD patients: a pharmaeconomic evaluation

    Directory of Open Access Journals (Sweden)

    Orietta Zaniolo

    2011-06-01

    Full Text Available Background: a secondary pre-specified analysis of the UPLIFT cohort demonstrated that the inclusion of tiotropium bromide in the routine care of GOLD stage II (moderate chronic obstructive pulmonary disease (COPD patients is associated with stronger improvements of survival, quality of life, and exacerbation rate than those shown in the total cohort; in this subgroup, tiotropium furthermore induces a significant reduction in the rate of FEV1 decline.Objective: to adapt the Spiriva® model, originally built to evaluate cost-effectiveness of tiotropium inclusion in the general COPD population, to GOLD II patients.Methods: the Spiriva® model is a probabilistic Markov patient-level simulation developed over a lifetime horizon to compare outcomes associated with the inclusion of tiotropium in routine care (RC for COPD treatment with those obtained with RC alone. Patients are characterised by gender, age, height, smoking status and FEV1. Model structure and sources have been maintained unvaried, except for demographic characteristics, specific for GOLD II patients, as extrapolated from an Italian observational study, and tiotropium efficacy, based on the secondary analysis of GOLD II UPLIFT patients. As in the original model, only direct health care costs are considered.Results: patients treated with tiotropium on average (95% CI gain 0.70 (0.00/7.23 LYs or 0.77 (0.02/4.67 QALYs compared to RC. The incremental lifetime cost is € 3,520 (-6,391/26,686, meaning that the incremental cost required to gain a QALY (incremental cost-effectiveness ratio – ICER is equal to € 4,548. Sensitivity analysis shows that tiotropium has a 50% probability of being cost-effective for a willingness-to-pay (WTP around 4,600 €/QALY; 100% probability is achieved with a WTP of € 9,300.Conclusions: the adoption of a strategy based on the inclusion of tiotropium from the early COPD stages represents good value for money in Italy, as the ICER estimated for GOLD II

  10. Evaluation of intubating conditions after rocuronium bromide in adults induced with propofol or thiopentone sodium

    Directory of Open Access Journals (Sweden)

    Moazzam Md Shahnawaz

    2011-01-01

    Full Text Available Aim: The aims of present study were to compare the propofol and rocuronium with thiopentone and rocuronium in terms of clinically satisfactory intubating conditions and to co-relate intubating conditions with degree of paralysis in adductor pollicis muscle using train of four ratio (TOFR. The intubating conditions were evaluated after rocuronium bromide 0.6 mg kg−1 at 60 s. Materials and Methods : 60 patients of ASA grades I-II of either sex, age 18-50 years, undergoing various elective surgical procedures were randomly divided into two groups, propofol rocuronium (PR group and thiopentone rocuronium (TR group of 30 patients in each. In the PR group, patients received propofol 2.5 mg kg−1 and rocuronium 0.6 mg kg−1 ; in TR group, patients received thiopentone 5 mg kg−1 and rocuronium 0.6 mg kg−1 . In all patients the intubating conditions were evaluated by the observer at 60 s. TOFR was measured at the time of intubation by an assistant. Results : In the PR group the number of the patients placed in intubating conditions grades I, II, III and IV were 40%, 36.67%, 13.33% and 10% and their mean TOFR were 31.8±17.9%, 61.8±;14.6%, 61.7±27.9%, and 78.3±5.7% respectively. While in theTR group the number of patients placed in intubating condition grade I, II, and III were 60%, 26.67%, and 13.33% and their mean TOFR , 41.2±28.3%, 68.0±10.9% and 78.7±6.8%, respectively. There was no patient in grade lV in theTR group. Conclusion : The clinical intubating conditions and degree of paralysis of adductor pollicis muscle after rocuronium 0.6 mg kg−1 at 60 s in adults induced with propofol or thiopentone sodium are comparable.

  11. Effect of aerosol inhalation of ipratropium bromide combined with budesonide and terbutaline on cytokines in children with bronchopneumonia

    Directory of Open Access Journals (Sweden)

    Xiang-Yu Che

    2016-09-01

    Full Text Available Objective: To explore the clinical efficacy of aerosol inhalation of ipratropium bromide combined with budesonide and terbutaline in the treatment of bronchopneumonia in children and the effect on cytokines. Methods: A total of 70 children with bronchopneumonia who were admitted in our hospital from March, 2015 to March, 2016 were included in the study and randomized into the study group and the control group. The patients in the control group were given anti-infection, oxygen inhalation, cough and asthma relieving, acidosis correcting, mask+oxygen driven aerosol inhalation of budesonide (0.5 mg/time and terbutaline (1.0 mg/time, with an oxygen flow rate of 5-7 L/min, 5-10 min every time, twice a day. On the above basis, the patients in the study group were given additional ipratropium bromide (1.0 mg/time. After 7-day treatment, the efficacy was evaluated. The levels of IL-6, TNF-毩, CRP, and WBC before and after treatment were detected. PEF, FVC, and FEV1 before and after treatment were detected. The improvement of clinical symptoms and signs, and the occurrence of adverse reactions were observed. Results: The levels of IL-6, TNF-毩, CRP, and WBC counting after treatment in the two groups were significantly reduced when compared with before treatment (P0.05. Conclusions: Ipratropium bromide combined with budesonide and terbutaline in the treatment of bronchopneumonia in children can rapidly relieve the symptoms, and improve the cytokine level, without obvious adverse reactions; therefore, it deserves to be widely recommended in the clinic.

  12. Evaluation of the mydriatic effects of topical administration of rocuronium bromide in Hispaniolan Amazon parrots (Amazona ventralis).

    Science.gov (United States)

    Petritz, Olivia A; Guzman, David Sanchez-Migallon; Gustavsen, Kate; Wiggans, K Tomo; Kass, Philip H; Houck, Emma; Murphy, Christopher J; Paul-Murphy, Joanne

    2016-01-01

    OBJECTIVE :To determine the mydriatic effects of topical rocuronium bromide administration in Hispaniolan Amazon parrots (Amazona ventralis) and to identify any adverse effects associated with treatment. Randomized crossover study. 8 healthy adult Hispaniolan Amazon parrots. Rocuronium bromide (20 μL/eye; 10 mg/mL) or saline (20 μL/eye; 0.9% NaCl) solution was administered in both eyes of each bird with a 26-day washout period. The birds were manually restrained in lateral recumbency with the apex of the cornea positioned upward for 2 minutes following administration in each eye. Infrared pupillometry and direct pupillary light reflex measurements were used to evaluate the mydriatic effects. Pupillary measurements were recorded prior to administration and every 20 minutes for 2 hours after administration, then hourly for a total of 7 hours. A brief physical examination was performed, direct pupillary light reflex was tested, and fluorescein staining was performed on each eye of each bird 24 hours after administration. A significant difference in pupillary diameter for the active versus control treatment group was noted from 20 to 360 minutes after drug administration, but not at 420 minutes. Minimal adverse effects were noted. Three birds had transient inferior eyelid paresis noted in both eyes after receiving rocuronium; 24 hours after the treatment, no differences in ocular measurements existed between the active and control treatments. Results suggested that topical rocuronium bromide administration may be safely used for pupillary dilation in Hispaniolan Amazon parrots and could be used for clinical evaluation, fundus imaging, and surgical interventions involving the lens and posterior segment in this species.

  13. Bromidotetra?kis?(1H-2-ethyl-5-methyl?imidazole-?N 3)copper(II) bromide

    OpenAIRE

    Godlewska, Sylwia; Baranowska, Katarzyna; Socha, Joanna; Do??ga, Anna

    2011-01-01

    The CuII ion in the title compound, [CuBr(C6H10N2)4]Br, is coordinated in a square-based-pyramidal geometry by the N atoms of four imidazole ligands and a bromide anion in the apical site. Both the CuII and Br− atoms lie on a crystallographic fourfold axis. In the crystal, the [CuBr(C6H10N2)4]+ complex cations are linked to the uncoordinated Br− anions (site symmetry overline{4}) by N—H...Br hydrogen bonds, generating a three-dimensional network. The ethyl group ...

  14. Bis(2,2′-bipyrid­yl)bromidocopper(II) bromide bromo­acetic acid hemihydrate

    OpenAIRE

    Liu, Yaru; Sun, Junshan; Wang, Xinli

    2009-01-01

    In the title compound, [CuBr(C10H8N2)2]Br·BrCH2COOH·0.5H2O, the CuII ion is coordinated by four N atoms [Cu—N = 1.985 (6)–2.125 (7) Å] from two 2,2′-bipyridine ligand molecules and a bromide anion [Cu—Br = 2.471 (2) Å] in a distorted trigonal-bipyramidal geometry. Short centroid–centroid distances [3.762 (5) and 3.867 (5) ...

  15. Efficacy and safety of eco-friendly inhalers: focus on combination ipratropium bromide and albuterol in chronic obstructive pulmonary disease

    Directory of Open Access Journals (Sweden)

    Panos RJ

    2013-04-01

    Full Text Available Ralph J Panos1,2 1Pulmonary, Critical Care, and Sleep Medicine Division, Cincinnati Veterans Affairs Medical Center, 2Pulmonary, Critical Care, and Sleep Medicine Division, University of Cincinnati College of Medicine, Cincinnati, OH, USA Background: Chronic obstructive pulmonary disease (COPD is a major cause of morbidity and mortality and its treatment is critical to improve quality of life, reduce symptoms, and diminish the frequency of COPD exacerbations. Due to the harmful environmental effects of pressurized metered-dose inhalers (pMDIs containing chlorofluorocarbons (CFCs, newer systems for delivering respiratory medications have been developed. Methods: A search of the literature in the PubMed database was undertaken using the keywords “COPD,” “albuterol,” “ipratropium bromide,” and “Respimat® Soft Mist Inhaler™”; pertinent references within the identified citations were included. The environmental effect of CFC-pMDIs, the invention of the Respimat® Soft Mist Inhaler™ (SMI (Boehringer Ingelheim, Ingelheim, Germany, and its use to deliver the combination of albuterol and ipratropium bromide for the treatment of COPD were reviewed. Results: The adverse environmental effects of CFC-pMDIs stimulated the invention of novel delivery systems including the Respimat SMI. This review presents its development, internal mechanism, and use to deliver the combination of albuterol and ipratropium bromide. Conclusion: CFC-pMDIs contributed to the depletion of the ozone layer and the surge in disorders caused by harmful ultraviolet B radiation. The banning of CFCs spurred the development of novel delivery systems for respiratory medications. The Respimat SMI is an innovative device that produces a vapor of inhalable droplets with reduced velocity and prolonged aerosol duration that enhance deposition within the lower airway and is associated with improved patient satisfaction. Clinical trials have demonstrated that the Respimat SMI

  16. Copper sulfate-pentahydrate-1,10-phenanthroline catalyzed amidations of alkynyl bromides. Synthesis of heteroaromatic amine substituted ynamides.

    Science.gov (United States)

    Zhang, Yanshi; Hsung, Richard P; Tracey, Michael R; Kurtz, Kimberly C M; Vera, Eymi L

    2004-04-01

    A practical cross-coupling of amides with alkynyl bromides using catalytic CuSO(4).5H(2)O and 1,10-phenanthroline is described here. This catalytic protocol is more environmentally friendly than the use of CuCN or copper halides and provides a general entry for syntheses of ynamides including various new sulfonyl and heteroaromatic amine substituted ynamides. Given the interest in ynamides, this N-alkynylation of amides should be significant for the future of ynamides in organic synthesis.

  17. Umeclidinium bromide versus placebo for people with chronic obstructive pulmonary disease (COPD).

    Science.gov (United States)

    Ni, Han; Htet, Aung; Moe, Soe

    2017-06-20

    People with chronic obstructive pulmonary disease (COPD) have poor quality of life, reduced survival, and accelerated decline in lung function, especially associated with acute exacerbations, leading to high healthcare costs. Long-acting bronchodilators are the mainstay of treatment for symptomatic improvement, and umeclidinium is one of the new long-acting muscarinic antagonists approved for treatment of patients with stable COPD. To assess the efficacy and safety of umeclidinium bromide versus placebo for people with stable COPD. We searched the Cochrane Airways Group Specialised Register (CAGR), ClinicalTrials.gov, the World Health Organization (WHO) trials portal, and the GlaxoSmithKline (GSK) Clinical Study Register, using prespecified terms, as well as the reference lists of all identified studies. Searches are current to April 2017. We included randomised controlled trials (RCTs) of parallel design comparing umeclidinium bromide versus placebo in people with COPD, for at least 12 weeks. We used standard Cochrane methodological procedures. If we noted significant heterogeneity in the meta-analyses, we subgrouped studies by umeclidinium dose. We included four studies of 12 to 52 weeks' duration, involving 3798 participants with COPD. Mean age of participants ranged from 60.1 to 64.6 years; most were males with baseline mean smoking pack-years of 39.2 to 52.3. They had moderate to severe COPD and baseline mean post-bronchodilator forced expiratory volume in one second (FEV 1 ) ranging from 44.5% to 55.1% of predicted normal. As all studies were systematically conducted according to prespecified protocols, we assessed risk of selection, performance, detection, attrition, and reporting biases as low.Compared with those given placebo, participants in the umeclidinium group had a lesser likelihood of developing moderate exacerbations requiring a short course of steroids, antibiotics, or both (odds ratio (OR) 0.61, 95% confidence interval (CI) 0.46 to 0.80; four

  18. The Liquid State

    Indian Academy of Sciences (India)

    like iron, aluminium, lead, zinc, etc .. Metals are cast ... dropping molten liquid of the alloys on a rapidly spinning copper wheel. ... Ed. Computer simulation studies in ... liquids, modelling ofliquids and study of the dynamic behaviour of liquids ...

  19. Remotely controllable liquid marbles

    KAUST Repository

    Zhang, Lianbin; Cha, Dong Kyu; Wang, Peng

    2012-01-01

    Liquid droplets encapsulated by self-organized hydrophobic particles at the liquid/air interface - liquid marbles - are prepared by encapsulating water droplets with novel core/shell-structured responsive magnetic particles, consisting of a

  20. Determination of bromide in aqueous solutions via the TlBr molecule using high-resolution continuum source graphite furnace molecular absorption spectrometry

    Science.gov (United States)

    Cacho, Frantisek; Machynak, Lubomir; Nemecek, Martin; Beinrohr, Ernest

    2018-06-01

    The paper describes the determination of bromide by evaluating the molecular absorption of thallium mono-bromide (TlBr) at the rotational line at 342.9815 nm by making use a high-resolution continuum source graphite furnace atomic absorption spectrometer. The effects of variables such as the wavelength, graphite furnace program, amount of Tl and the use of a modifier were investigated and optimized. Various chemical modifiers have been studied, such as Pd, Mg, Ag and a mixture of Pd/Mg. It was found that best results were obtained by using Ag which prevents losses of bromide during pyrolysis step through precipitation of bromide as AgBr. In this way, a maximum pyrolysis temperature of 400 °C could be used. The optimum molecule forming temperature was found to be 900 °C. Bromide concentrations in various water samples (CRM, bottled drinking water and tap water) were determined. The quantification was made by both linear calibration and standard addition techniques. The results were matched well those of the reference method. The calibration curve was linear in the range between 1 and 1000 ng Br with a correlation coefficient R = 0.999. The limit of detection and characteristic mass of the method were 0.3 ng and 4.4 ng of Br.