WorldWideScience

Sample records for lioh content producing

  1. Autoclave corrosion of zircaloy-4 cladding samples in LiOH solutions

    International Nuclear Information System (INIS)

    Hermann, A.

    2010-03-01

    In reactor operation, pH of the cooling water is adjusted by addition of alkaline hydroxides, and LiOH has been found to be the most suitable one. The addition of LiOH above a certain concentration level (depending on temperature) increases the corrosion rate of zirconium and its alloys. Hydrogen pick-up by the metal is also increased, and this effect is used to produce hydrided specimens for different investigations using the corrosion reaction. At the Paul Scherrer Institute several projects were accomplished to investigate the influence of hydrogen in Zircaloy cladding on its mechanical properties. In order to produce hydrided specimens for comparison and for adjusting new equipment, Zircaloy tubing samples were hydrogen charged by autoclave corrosion in lithiated water. Results of the corrosion experiments are outlined in this publication. Because of the great variety of possible experimental parameters these results are still of interest for the scientific community. Autoclave corrosion was accomplished in 0.2 M or 0.5 M LiOH solution at a constant temperature of 340 o C and a pressure of 160 bar. The corrosion rate increases from 84 mg/(dm 2 d) in 0.2 M LiOH to 153 mg/(dm 2 d) in 0.5 M LiOH. The hydrogen pick-up fraction in 0.5 M LiOH amounts to 80%. In 0.5 M LiOH, Zircaloy tubing samples can be charged with ∼ 500 ppm hydrogen in about 40 hours. In the corrosion experiments described in this report a homogeneous distribution of hydrides should be expected (except very high hydride concentrations) because no temperature gradient exists through the tubing wall. Hydrogen stringers are homogeneously distributed with circumferential orientation (stress-relieved tubing samples). (author)

  2. Fabrication and characterization of lithium orthosilicate pebbles using LiOH as a new raw material

    International Nuclear Information System (INIS)

    Knitter, R.; Reimann, J.; Risthaus, P.; Boccaccini, L.V.; Piazza, G.

    2004-01-01

    For the European Helium Cooled Pebble Bed (HCPB) blanket slightly overstoichiometric lithium orthosilicate pebbles (Li 4 SiO 4 +SiO 2 ) have been chosen as one optional breeder material. This material is developed in collaboration between Research Centre Karlsruhe (FZK) and the Schott Glas, Mainz. The lithium orthosilicate (OSi) pebbles are fabricated by the melting and spraying method in a semi-industrial scale facility. In the past, the not enriched pebbles were produced from a mixture of Li 4 SiO 4 and SiO 2 powders, but due to the fact that enriched Li 4 SiO 4 is not available on the market, highly enriched carbonate powder was used that finally resulted in nonsatisfying pebble characteristics. Enriched LiOH powder is commercially available, therefore, a new production route was pursued based on the following, simplified reaction: 4 LiOH + SiO 2 → Li 4 SiO 4 + 2 H 2 O. The melting process of LiOH and SiO 2 is less difficult to control than the melting of Li 2 CO 3 in spite of the decomposition of water. The pebbles produced from LiOH and SiO 2 are similar to those produced from Li 4 SiO 4 and SiO 2 . They exhibit a distinctly dendritic structure and show only a small amount of pores and cracks. In addition to the main constituent Li 4 SiO 4 , the high temperature phase Li 6 Si 2 O 7 was detected due to the quenching process and the excess of SiO 2 . This minor constituent, however, decomposes to Li 4 SiO 4 and Li 2 SiO 3 during annealing. In compressive crush load tests of single pebbles a crush load of about 9.5 N was measured for pebbles after drying at 300degC. The chemical analysis revealed a further advantage of the use of LiOH in the melting process. As LiOH is available in high-purity quality, the pebbles contain impurities to a lower degree than pebbles produced from Li 4 SiO 4 or Li 2 CO 3 . In order to obtain characteristic pebble bed data, first Uniaxial Compression Tests (UCTs) were performed at temperatures between ambient and at 850deg

  3. Understanding LiOH chemistry in a ruthenium-catalyzed Li-O{sub 2} battery

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Tao; Liu, Zigeng; Kim, Gunwoo; Grey, Clare P. [Department of Chemistry, University of Cambridge (United Kingdom); Frith, James T.; Garcia-Araez, Nuria [Department of Chemistry, University of Southampton (United Kingdom)

    2017-12-11

    Non-aqueous Li-O{sub 2} batteries are promising for next-generation energy storage. New battery chemistries based on LiOH, rather than Li{sub 2}O{sub 2}, have been recently reported in systems with added water, one using a soluble additive LiI and the other using solid Ru catalysts. Here, the focus is on the mechanism of Ru-catalyzed LiOH chemistry. Using nuclear magnetic resonance, operando electrochemical pressure measurements, and mass spectrometry, it is shown that on discharging LiOH forms via a 4 e{sup -} oxygen reduction reaction, the H in LiOH coming solely from added H{sub 2}O and the O from both O{sub 2} and H{sub 2}O. On charging, quantitative LiOH oxidation occurs at 3.1 V, with O being trapped in a form of dimethyl sulfone in the electrolyte. Compared to Li{sub 2}O{sub 2}, LiOH formation over Ru incurs few side reactions, a critical advantage for developing a long-lived battery. An optimized metal-catalyst-electrolyte couple needs to be sought that aids LiOH oxidation and is stable towards attack by hydroxyl radicals. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. A preliminary report on the effects of long-term exposure of LiOH on pure nickel

    Science.gov (United States)

    Whittenberger, J. D.

    1987-01-01

    A 'bread pan' capsule has been designed which allows large numbers of tensile specimens to be simultaneously exposed to molten LiOH, its vapor, and vacuum. Capsules and specimens fabricated from the pure nickel alloy Ni-200 were annealed for 401 hours and 2500 hours at 775 K. Examination of the exposed materials revealed that little outward damage in terms of visible attack, weight change, or loss of room temperature tensile properties occurred. In particular, the mechanical behavior of hydroxide-contaminated alloy was essentially identical to that receiving a simple thermal exposure in vacuum. Examination of the microstructures revealed that LiOH did produce some nonuniform, shallow intergranular corrosion in NI-200; however, the extent of the damage was insufficient to produce weakening or embrittlement.

  5. LiOH - H2O2 - H2O trinary system study for the selection of optimal conditions of lithium peroxide synthesis

    International Nuclear Information System (INIS)

    Nefedov, R A; Ferapontov, Yu A; Kozlova, N P

    2016-01-01

    Using solubility method the decay kinetics of peroxide products contained in liquid phase of LiOH - H 2 O 2 - H 2 O trinary system with 2 to 6% by wt hydrogen peroxide content in liquid phase in 21 to 33 °C temperature range has been studied. Conducted studies have allowed to determine temperature and concentration limits of solid phase existence of Li 2 O 2 ·H 2 O content, distinctness of which has been confirmed using chemical and qualitative X- ray phase analysis. Stabilizing effect of solid phase of Li 2 O 2 ·H 2 O content on hydrogen peroxide decay contained in liquid phase of LiOH - H 2 O 2 - H 2 O trinary system under conditions of experiments conducted has been shown. (paper)

  6. LiOH - H2O2 - H2O trinary system study for the selection of optimal conditions of lithium peroxide synthesis

    Science.gov (United States)

    Nefedov, R. A.; Ferapontov, Yu A.; Kozlova, N. P.

    2016-01-01

    Using solubility method the decay kinetics of peroxide products contained in liquid phase of LiOH - H2O2 - H2O trinary system with 2 to 6% by wt hydrogen peroxide content in liquid phase in 21 to 33 °C temperature range has been studied. Conducted studies have allowed to determine temperature and concentration limits of solid phase existence of Li2O2·H2O content, distinctness of which has been confirmed using chemical and qualitative X- ray phase analysis. Stabilizing effect of solid phase of Li2O2·H2O content on hydrogen peroxide decay contained in liquid phase of LiOH - H2O2 - H2O trinary system under conditions of experiments conducted has been shown.

  7. Origin of the OH vibrational blue shift in the LiOH crystal.

    Science.gov (United States)

    Hermansson, Kersti; Gajewski, Grzegorz; Mitev, Pavlin D

    2008-12-25

    The O-H vibrational frequency in crystalline hydroxides is either upshifted or downshifted by its crystalline surroundings. In the LiOH crystal, the experimental gas-to-solid O-H frequency upshift ("blue shift") is approximately +115 cm(-1). Here plane-wave DFT calculations for the isotope-isolated LiOH crystal have been performed and we discuss the origin of the OH frequency upshift, and the nature of the OH group and the interlayer interactions. We find that (1) the vibrational frequency upshift originates from interactions within the LiOH layer; this OH upshift is slightly lessened by the interlayer interactions; (2) the interlayer O-H - - - H-O interaction is largely electrostatic in character (but there is no hydrogen bonding); (3) the gas-to-solid vibrational shift for OH in LiOH(s) and its subsystems qualitatively adheres to a parabola-like "frequency vs electric field strength" correlation curve, which has a maximum for a positive electric field, akin to the correlation curve earlier found in the literature for an isolated OH(-) ion in an electric field.

  8. Effect of calcium on the electrochemical behavior of lithium anode in LiOH aqueous solution used for lithium–water battery

    International Nuclear Information System (INIS)

    Zhang Ziyan; Chen Kanghua; Ni Erfu

    2012-01-01

    The effect of minor addition of calcium to lithium anode on the electrochemical behavior of lithium anode in 4 M LiOH at 30 °C temperature is investigated by hydrogen collection, polarization curves and electrochemical impedance spectroscopy. The results show that the hydrogen evolution rate is marginally reduced with increasing calcium content. Addition of calcium to lithium mainly inhibits the anodic process. Minor addition of calcium to lithium slightly reduced the discharge current of lithium anode. Minor addition of calcium to lithium anode marginally enhances the hydrogen inhibition of lithium by the formation of calcium hydride combined with LiOH and LiOH·H 2 O formed on the anode surface.

  9. Properties of pure nickel after long term exposures to LiOH and vacuum at 775 K

    Science.gov (United States)

    Whittenberger, J. D.

    1991-01-01

    The solid to liquid phase transformation of LiOH at 744.3 K is considered to be an ideal candidate thermal energy storage (TES) mechanism for a Rankine heat engine based solar dynamic system operating at approximately 682 K. While pure nickel is thought to be a suitable containment material for LiOH, long term containment is of concern because molten hydroxides are usually corrosive. Two commercially pure nickel alloys, Ni-200 and Ni-201, were exposed to molten LiOH, its vapor, and vacuum at 775 K for periods ranging from 50 to 5000 h, and simple mechanical property measurements (77 to 900 K tensile and 750 K creep rupture) of exposed alloys were undertaken. The mechanical property test procedures are described and tabular lists of the test data are presented.

  10. Development and optimization of a modified process for producing the battery grade LiOH: Optimization of energy and water consumption

    International Nuclear Information System (INIS)

    Grágeda, Mario; González, Alonso; Alavia, Wilson; Ushak, Svetlana

    2015-01-01

    LiOH·H 2 O is used for preparation of alkaline batteries. The required characteristics of this compound are low levels of impurities and a specific particle size distribution. LiOH·H 2 O is produced from ore and brines. In northern Chile, lithium is produced from brines. This region presents particular desert climate conditions where water and energy are scarce. To help solve this problem, the conventional production process for battery grade LiOH·H 2 O was simulated and a modified process was developed, with an efficient consumption of energy and water, to improve the environmental sustainability of the plant, and greater process yield and product purity. Different configurations of the equipments were studied and for the best configurations the behavior of the modified process at different scenarios were simulated. It was found that the purity is independent of concentration used in feed to thickeners. The process yield increases in average 2.4% for modified process due to recycling operation. In modified process is obtained 28% more product mass, specific energy consumption decreases up to 4.8% and losses of Li/kg of product decreased by 83% compared to conventional process. The water consumption per kg of product in modified process is 1%–6.3%, being lower than in conventional process. The results presented can be considered as guidelines to address the optimization of the industrial process for obtaining the battery grade LiOH. - Highlights: • Water and energy are important resources in any sustainable industrial process. • High purity LiOH·H 2 O is a material for producing of lithium batteries. • Conventional and modified optimized processes for LiOH·H 2 O production were simulated. • Energy and water consumptions decrease for the modified process. • Optimal operational conditions of H 2 O, feed, pressure and energy were established

  11. Cation incorporation into zirconium oxide in LiOH, NaOH, and KOH solutions

    International Nuclear Information System (INIS)

    Jeong, Y.H.; Kim, K.H.; Baek, J.H.

    1999-01-01

    To investigate the cation incorporation into zirconium oxide, SIMS analysis was performed on the specimens prepared to have an equal oxide thickness in LiOH, NaOH, and KOH solutions. Even though they have an equal oxide thickness in LiOH, NaOH, and KOH solutions, the penetration depth of cation into the oxide decreased with an increase in the ionic radius of cation. The cation is considered to control the corrosion in alkali hydroxide solutions and its effect is dependent on the concentration of alkali and the oxide thickness. The slight enhancement of the corrosion rate at a low concentration is thought to be caused by cation incorporation into oxide, while the significant acceleration at a high concentration is due to the transformation of oxide microstructures that would be also induced by cation incorporation into oxide. (orig.)

  12. Comparison of two analytical methods for the local quantitative determination of lithium and boron contents in cladding materials

    International Nuclear Information System (INIS)

    Gavillet, D.; Guenther-Leopold, I.; Martin, M.; Guillong, M.; Hellwig, Ch.; Sell, H.J.

    2008-01-01

    Pressurized water reactors contain boric acid for reactivity control. As the acidic coolant conditions result in an increased attack of the circuit materials, LiOH is added to render the coolant slightly alkaline. However, LiOH can affect corrosion of the Zr alloy cladding. Thus the Li content in the oxide layers of irradiated fuel rods is of high interest, especially for new alloys (pathfinder rods). At the 'Paul Scherrer Institut' the lithium as well as the boron content in the oxide layers of claddings are determined by Secondary Ion Mass Spectrometry (SIMS). Quantification is performed by direct comparison with a Zircaloy-oxide layer implanted with B and Li. A new and independent method using Laser Ablation Inductively Coupled Plasma Mass Spectrometry was applied to cross-check the SIMS data. (authors)

  13. Raman spectra from very concentrated aqueous NaOH and from wet and dry, solid, and anhydrous molten, LiOH, NaOH, and KOH.

    Science.gov (United States)

    Walrafen, George E; Douglas, Rudolph T W

    2006-03-21

    High-temperature, high-pressure Raman spectra were obtained from aqueous NaOH solutions up to 2NaOHH2O, with X(NaOH)=0.667 at 480 K. The spectra corresponding to the highest compositions, X(NaOH)> or =0.5, are dominated by H3O2-. An IR xi-function dispersion curve for aqueous NaOH, at 473 K and 1 kbar, calculated from the data of Franck and Charuel indicates that the OH- ion forms H3O2- by preferential H bonding with nonhydrogen-bonded OH groups. Raman spectra from wet to anhydrous, solid LiOH, NaOH, and KOH yield sharp, symmetric OH- stretching peaks at 3664, 3633, and 3596 cm(-1), respectively, plus water-related, i.e., H3O2-, peaks near LiOH, 3562 cm(-1), NaOH, 3596 cm(-1), and, KOH, 3500 cm(-1). Absence of H3O2- peaks from the solid assures that the corresponding melt is anhydrous. Raman spectra from the anhydrous melts yield OH- stretching peak frequencies: LiOH, 3614+/-4 cm(-1), 873 K; NaOH, 3610+/-2 cm(-1), 975 K; and, KOH, 3607+/-2 cm(-1), 773 K, but low-frequency asymmetry due to ion-pair interactions is present which is centered near 3550 cm(-1). The ion-pair-related asymmetry corresponds to the sole IR maximum near 3550 cm(-1) from anhydrous molten NaOH, at 623 K. Bose-Einstein correction of published low-frequency Raman data from molten LiOH revealed an acoustic phonon, near 205 cm(-1), related to restricted translation of OH- versus Li+, and an optical phonon, at 625 cm(-1) and tau approximately 0.05 ps, due to protonic precession and/or pendular motion. Strong H bonding between water and the O atom of OH- forms H3O2-, but the proton of OH- does not bond with H significantly. Large Raman bandwidths (aqueous solutions) are explained in terms of inhomogeneous broadening due to proton transfer in a double well. Vibrational assignments are presented for H3O2-.

  14. Selenium content of foods purchased or produced in Ohio.

    Science.gov (United States)

    Snook, J T; Kinsey, D; Palmquist, D L; DeLany, J P; Vivian, V M; Moxon, A L

    1987-06-01

    Approximately 450 samples of about 100 types of foods consumed by rural and urban Ohioans were analyzed for selenium. Meat, dairy products, eggs, and grain products produced in Ohio have considerably lower selenium content than corresponding products produced in high selenium areas, such as South Dakota. Retail Ohio foods with interregional distribution tended to be higher in selenium content than corresponding foods produced in Ohio. Best sources of selenium in Ohio foods commonly consumed were meat and pasta products. Poor sources of selenium were fruits, most vegetables, candies, sweeteners, and alcoholic and nonalcoholic beverages. Establishment of an accurate data base for selenium depends on knowledge of the interregional distribution of foods, the selenium content of foods at their production site, and the selenium content of foods with wide local distribution.

  15. The influence of bismuth oxide doping on the rechargeability of aqueous cells using MnO2 cathode and LiOH electrolyte

    International Nuclear Information System (INIS)

    Minakshi, Manickam; Mitchell, David R.G.

    2008-01-01

    Bi-doped manganese dioxide (MnO 2 ) has been prepared from γ-MnO 2 by physical admixture of bismuth oxide (Bi 2 O 3 ). The doping improved the cycling ability of the aqueous cell. These results are discussed and compared with the electrochemical behavior of bismuth-free MnO 2 . Batteries using the traditional potassium hydroxide (KOH) electrolyte are non-rechargeable. However, with lithium hydroxide (LiOH) as an electrolyte, the cell becomes rechargeable. Furthermore, the incorporation of bismuth into MnO 2 in the LiOH cell was found to result in significantly longer cycle life, compared with cells using undoped MnO 2 . The Bi-doped cell exhibited a greater capacity after 100 discharge cycles, than the undoped cell after just 40 cycles. X-ray diffraction and the microscopic analysis suggest that the presence of Bi 3+ ions reduces the magnitude of structural changes occurring in MnO 2 during cycling. Comparison with additives assessed in our previous studies (titanium disulfide (TiS 2 ); titanium boride (TiB 2 )) shows that the best rechargeability behavior is obtained for the current Bi-doped MnO 2 . As the size of Bi 3+ ions (0.96 A) is much larger than Mn 3+ (0.73 A) or Mn 2+ (0.67 A) they have effectively prevented the formation of non-rechargeable products

  16. Effect of LiOH, NaOH and KOH on corrosion and oxide microstructure of Zr-based alloys

    International Nuclear Information System (INIS)

    Jeong, Y.H.; Kim, H.G.; Jung, Y.H.; Ruhmann, H.

    1999-01-01

    Long-term corrosion test, SIMS analysis, and TEM microstructural study were carried out to investigate the corrosion characteristics and mechanism of Zr alloys in alkali hydroxides. The corrosion tests were performed in solutions of LiOH, NaOH, KOH, RbOH, and CsOH at 350 deg. C for 500 days. SIMS analysis was performed for the specimens prepared to have an equal oxide thickness. TEM studies on the specimens with an equal oxide thickness in various solutions in both pre- and post-transition regimes were also conducted. The corrosion rate in alkali hydroxide solutions was observed to decrease as the ionic radius of alkali cation was increased. The penetration depth of cation into the oxide decreases with increasing the ionic radius of cation. Even though the oxide thickness was equal, the different oxide morphologies were observed in specimens. Namely, in LiOH solution the oxide morphology was transformed early from columnar to equiaxed structure. However, in KOH solution the columnar structure was maintained up to post-transition regime. Based on the corrosion test, SIMS analysis, and microstructural study, the cation is considered to control the corrosion in a alkali hydroxide solution and its effect is dependent on the concentration of alkali and the oxide thickness. The slight acceleration of the corrosion rate at a low concentration is thought to be caused by cation incorporation into oxide while the significant acceleration at a high concentration is due to the transformation of oxide microstructure that would be induced by cation incorporation. KOH was shown not to affect significantly the corrosion and the hydrogen pickup of Zircaloy. Therefore, it has a potential for PWR application only from the point of view of Zircaloy corrosion. (author)

  17. In situ measurement of the effect of LiOH on the stability of zircaloy-2 surface film in PWR water

    International Nuclear Information System (INIS)

    Saario, T.; Taehtinen, S.

    1997-01-01

    Surface films on the metals play a major role in corrosion assisted cracking. A new method called Contact Electric Resistance (CER) method has been recently developed for in situ measurement of the electric resistance of surface films in high temperature and high pressure environments. The technique has been used to determine in situ the electric resistance of films on metals when in contact with water and dissolved anions, during formation and destruction of oxides and hydrides and during electroplating of metals. Electric resistance data can be measured with a frequency of the order of one hertz, which makes it possible to investigate in situ the kinetics of surface film related processes which are dependent on the environment, temperature, pH and electrochemical potential. This paper presents the results of the CER investigation on the effects of LiOH on the stability of Zircaloy-2 surface film in water with 2000 ppm H 3 BO 3 . At 300 deg. C the LiOH concentrations higher than 10 -2 M (roughly 70 ppm of Li + ) were found to markedly reduce the electric resistance of the Zircaloy-2 surface film during a test period of less than two hours. The decrease of the film resistance is very abrupt, possibly indicating a phase transformation. Moreover, the advantages of the CER technique over the other competing techniques which rely on the measurement of current are discussed. (author)

  18. In situ measurement of the effect of LiOH on the stability of zircaloy-2 surface film in PWR water

    Energy Technology Data Exchange (ETDEWEB)

    Saario, T; Taehtinen, S [Technical Research Centre of Finland, Espoo (Finland)

    1997-02-01

    Surface films on the metals play a major role in corrosion assisted cracking. A new method called Contact Electric Resistance (CER) method has been recently developed for in situ measurement of the electric resistance of surface films in high temperature and high pressure environments. The technique has been used to determine in situ the electric resistance of films on metals when in contact with water and dissolved anions, during formation and destruction of oxides and hydrides and during electroplating of metals. Electric resistance data can be measured with a frequency of the order of one hertz, which makes it possible to investigate in situ the kinetics of surface film related processes which are dependent on the environment, temperature, pH and electrochemical potential. This paper presents the results of the CER investigation on the effects of LiOH on the stability of Zircaloy-2 surface film in water with 2000 ppm H{sub 3}BO{sub 3}. At 300 deg. C the LiOH concentrations higher than 10{sup -2} M (roughly 70 ppm of Li{sup +}) were found to markedly reduce the electric resistance of the Zircaloy-2 surface film during a test period of less than two hours. The decrease of the film resistance is very abrupt, possibly indicating a phase transformation. Moreover, the advantages of the CER technique over the other competing techniques which rely on the measurement of current are discussed. (author).

  19. Low Temperature Particle Filtration of Producer Gas with Low Tar Content

    DEFF Research Database (Denmark)

    Hindsgaul, Claus

    This report describes the tests of different techniques for removing the particulates from producer gas from the 100 kW two-stage down-draft gasifier at DTU1 . The goal of the tests was to identify and implement methods to remove soot particles from producer gas with low tar content. During the f...

  20. Preparation of lithium indium oxide via a rheological phase route and its electrochemical characteristics in LiOH and Li{sub 2}SO{sub 4} solutions

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Guo-Qing [Department of Chemistry and Environment Science of Yangtze Normal University, 408100 Chongqing (China); College of Chemistry and Chemical Engineering of Chongqing University, Chongqing 400030 (China); Zhang, Sheng-Tao [College of Chemistry and Chemical Engineering of Chongqing University, Chongqing 400030 (China); Wu, Xing-Fa [Department of Chemistry and Environment Science of Yangtze Normal University, 408100 Chongqing (China)

    2010-01-15

    Submicrometer-sized lithium indium oxide (LiInO{sub 2}) powder via a rheological phase method using trilithium citrate tetra hydrate (C{sub 6}H{sub 5}Li{sub 3}O{sub 7} . 4H{sub 2}O) and indium oxide (In{sub 2}O{sub 3}) has been prepared in this work for the first time. The optimal pyrolyzing temperature range to prepare crystalline LiInO{sub 2} is between 650 and 900 C, which was confirmed by thermal gravimetric and differential thermogravimetric analysis of the precursor and X-ray diffraction analysis. The pure phase LiInO{sub 2} sample obtained has a uniform particle morphology and submicrosize, which was observed by scanning electron microscopy. The electrochemical studies show that a new pair of cathodic and anodic peaks at 0.23 and 0.38 V (vs. saturated calomel electrode) was obviously observed from the cyclic voltammetry curve of LiInO{sub 2} in 1 M LiOH solution, indicating a battery characteristic of the material in this electrolyte. While in 1 M Li{sub 2}SO{sub 4} solution, the sample presents a supercapacitive characteristic within the same potential range. The reasons for different electrochemical behaviors in these two electrolytes can be attributed to the fact that the reaction of lithium ion insertion/extraction into/out of a LiInO{sub 2} electrode takes place in the bulk material in LiOH electrolyte solution, whereas it takes place on the electrode/electrolyte interface for Li{sub 2}SO{sub 4} electrolyte case. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  1. Mineral content of the honey produced in Zulia state, Venezuela.

    Science.gov (United States)

    Sulbarán de Ferrer, Betzabé; Ojeda de Rodríguez, Graciela; Peña, Jorge; Martínez, Janeth; Morán, María

    2004-09-01

    The mineral content of the honey produced in five zones of the Zulia state, Venezuela, during dry and rainy seasons was determined. The analyzed elements were: sodium, potassium (by emission spectroscopy), calcium, magnesium, copper, iron, manganese (by atomic absorption spectroscopy), phosphorus (phosphate ions, by colorimetric method), and ash content of raw honey samples directly collected from different beekeepers. The mean values for Na, K, Ca, Mg, Cu, Fe, Mn, and P were 353+84; 1774+138; 237+66; 52+24; 0.76+0.43; 13.5+10.23; 0.92+0.42 and 1642+323 mg/kg respectively. The mean ash content was 0.431+0.15%. Potassium was the most abundant of the elements determined. This results confirm that Zulian honey can be considered a good source of minerals.

  2. High oleic acid content materials of rapeseed (Brassica napus) produced by radiation breeding

    International Nuclear Information System (INIS)

    Guan Chunyun; Liu Chunlin; Chen Sheyuan

    2006-01-01

    High oleic acid content rapeseed breeding has great significance, because high oleic acid oil is a healthy and nutritious oil, which is of a long shelflife and also propitious to producing biodiesel fuel. The high oleic acid content breeding materials of rapeseed (B. napus) were obtained by 80-100 kR ~(60)Co gamma ray ionizing radiation treatment of dry seeds and continuous selection. The results showed that the oleic acid contents of M (2), M (3) and M (4) progenies increased by different grades. Moreover, the oleic acid content of M (5) progeny increased greatly. The oleic acid contents were higher than 70% in the most of the plants and the highest one reached 93.5 %. The base G was transited by base A in fad (2) gene at the 270 site of high oleic acid mutation (M(6) 04-855). The location is at the beta folding area and conservative area of this protein. Base mutation at sites 1 044 and 1 062 also led to produce a stop condon. These changes in structure led to loss the function of fad (2). According to molecular mechanism of gene mutation, no matter what transvertion or transition happens, several replications are needed. That is to say several generations are needed. That was also the reason why high oleic acid content mutation occurred in later generations

  3. Performance and emission comparison of a supercharged dual-fuel engine fueled by producer gases with varying hydrogen content

    Energy Technology Data Exchange (ETDEWEB)

    Mohon Roy, Murari [Rajshahi University of Engineering and Technology (JSPS Research Fellow, Okayama University), Tsushima-Naka 3, Okayama 700-8530 (Japan); Department of Mechanical Engineering, Okayama University, Tsushima-Naka 3, Okayama 700-8530 (Japan); Tomita, Eiji; Kawahara, Nobuyuki; Harada, Yuji [Department of Mechanical Engineering, Okayama University, Tsushima-Naka 3, Okayama 700-8530 (Japan); Sakane, Atsushi (Mitsui Engineering and Shipbuilding Co. Ltd., 6-4 Tsukiji 5-chome, Chuo-ku, Tokyo)

    2009-09-15

    This study investigated the effect of hydrogen content in producer gas on the performance and exhaust emissions of a supercharged producer gas-diesel dual-fuel engine. Two types of producer gases were used in this study, one with low hydrogen content (H{sub 2} = 13.7%) and the other with high hydrogen content (H{sub 2} = 20%). The engine was tested for use as a co-generation engine, so power output while maintaining a reasonable thermal efficiency was important. Experiments were carried out at a constant injection pressure and injection quantity for different fuel-air equivalence ratios and at various injection timings. The experimental strategy was to optimize the injection timing to maximize engine power at different fuel-air equivalence ratios without knocking and within the limit of the maximum cylinder pressure. Two-stage combustion was obtained; this is an indicator of maximum power output conditions and a precursor of knocking combustion. Better combustion, engine performance, and exhaust emissions (except NO{sub x}) were obtained with the high H{sub 2}-content producer gas than with the low H{sub 2}-content producer gas, especially under leaner conditions. Moreover, a broader window of fuel-air equivalence ratio was found with highest thermal efficiencies for the high H{sub 2}-content producer gas. (author)

  4. Equilibrium moisture content of OSB panels produced with veneer inclusion and different types of adhesive

    Directory of Open Access Journals (Sweden)

    Lourival Marin Mendes

    2014-03-01

    Full Text Available The aim of this study was to evaluate different statistical models to estimate the equilibrium moisture content of OSB panels exposed to different conditions of air temperature and relative humidity, And also to evaluate the influence of the adhesive and veneer inclusion in the equilibrium moisture content. The panels were produced with three different adhesive types (phenol-formaldehyde - FF, melamine-urea-formaldehyde - MUF, and phenol-melamine-urea-formaldehyde - PMUF and with and without veneer inclusion. The evaluation of the equilibrium moisture content of the panels was carried out at temperatures of 30, 40 and 50°C and relative humidity of 40, 50, 60, 70, 80 and 90%. The modeling of equilibrium moisture content was performed using the statistical non-linear and polynomial models. In general, the polynomial models are most indicated for determining the equilibrium moisture content of OSB. The models adjusted only with air relative humidity presented the best precision measurements. The type of adhesive affected the equilibrium moisture content of the panels, being observed for adhesives PMUF and FF the same trend of variation, and the highest values obtained for the panels produced with adhesive MUF. The veneer inclusion decreased the equilibrium moisture content only in the panels with MUF adhesive.

  5. Polonium 210 content in foodstuffs produced in Bulgaria

    International Nuclear Information System (INIS)

    Keslev, D.; Novakova, E.; Boyadzhiev, A.; Kerteva, A.

    1975-01-01

    A study of the content of polonium-210 in a variety of foodstuffs produced in Bulgaria in 1970 revealed peak radionuclide concentration in wheat - 6.7 pCi/kg, followed by prunes - 2.2 pCi/kg, cabbage - 1.86 pCi/kg, peppers - 1.64 pCi/kg. The content of polonium-210 in onions, meat and potatoes was low (0.5, 0.8 and 0.9 pCi/kg accordingly). All other food products studied - milk, bread, beans, eggs, tomatoes, apples, pears, grapes and drinking water - appeared to have approximately equal polonium-210 concentration - from 1.21 to 1.35 pCi/kg. The daily intake of polonium-210 with food and water amounted accordingly to 1.61, 1.79 and 2.08 pCi/kg in preschool children, in school children and in senile individuals. The major part (68 - 82 per cent) of incorporated polonium-210 was eliminated with the stools. In all age groups the amount of polonium-210 removed daily from the body with the excreta corresponded to the intake, i.e. the balance of polonium-210 was in a state of equilibrium. The age factor in all three groups exerted no effect on the radionuclide intake and elimination from the body. (Ch.K.)

  6. Evaluation of the nitrate content in leaf vegetables produced through different agricultural systems.

    Science.gov (United States)

    Guadagnin, S G; Rath, S; Reyes, F G R

    2005-12-01

    The nitrate content of leafy vegetables (watercress, lettuce and arugula) produced by different agricultural systems (conventional, organic and hydroponic) was determined. The daily nitrate intake from the consumption of these crop species by the average Brazilian consumer was also estimated. Sampling was carried out between June 2001 to February 2003 in Campinas, São Paulo State, Brazil. Nitrate was extracted from the samples using the procedure recommended by the AOAC. Flow injection analysis with spectrophotometric detection at 460 nm was used for nitrate determination through the ternary complex FeSCNNO+. For lettuce and arugula, the average nitrate content varied (p hydroponic system. For watercress, no difference (p hydroponic samples, both having higher nitrate contents (p hydroponic system, represented 29% of the acceptable daily intake established for this ion.

  7. The production of lithium oxide microspheres from the disintegration of a liquid jet

    International Nuclear Information System (INIS)

    Al-Ubaidi, M.R.; Anno, J.N.

    1989-01-01

    Microspheres of lithium hydroxide (LiOH) were produced from in-flight solidification of droplets formed by the disintegration of an acoustically driven, mechanically vibrated cylindrical liquid jet of molten LiOH. The molten material at 470 to 480 degrees C was fed through a 25-gauge (0.0267-cm bore diameter) nozzle, interiorly electroplated with silver, under ∼27.6-kPa (4-psig) pressure, and at a mechanical vibration frequency of 10 Hz. The resulting jet issued into a 5.5-cm-diam vertical glass drop tube entraining a 94.5 cm 3 /s (12 ft 3 /h) argon gas stream at 75 degrees C. The 100-cm-long drop tube was sufficient to allow the droplets of molten LiOH resulting from jet disintegration to solidify in-flight without catastrophic thermal shock, being then collected a solid microspheres. These LiOH microspheres were then vacuum processed to lithium oxide (Li 2 O). Preliminary experiments resulted in microspheres with diameters varying from 120 to 185 μm, but with evidence of impurity contamination occurring during the initial stages of the process

  8. Application of laser-produced-plasmas to determination of carbon content in steel

    International Nuclear Information System (INIS)

    Ortiz, M.; Aragon, C.; Aguilera, J.A.; Campos, J.

    1994-01-01

    This paper describes an analytical method to determine carbon content in solid and molten steel. It is based on the study of the emission spectrum from a Nd-YAG laser produced plasma. The light emitted from the plasma is focused to the entrance slit of a spectrometer and detected by an OMA III system. For every laser pulse an spectral range of 100 A are recorded. With the use of time-resolved spectroscopy a precision of 1.6% and a detection limit of 65 ppm of carbon content in steel have been obtained. These values are similar to those of other accurate conventional techniques but using optics fiber and laser excitation it is possible to made sample calibrations in hostile environments. Also, as the analysis are made in real time changes in sample composition can be measured without stopping production processes. (Author) 26 refs

  9. Application of laser-produced-plasmas to determination of carbon content in steel

    International Nuclear Information System (INIS)

    Ortiz, M.; Aragon, C.; Aguilera, J. A.; Campos, J.

    1994-01-01

    This paper describes an analytical method to determine carbon content in solid and molten steel. It is based on the study of the emission spectrum from a Nd-YAG laser produced plasma. The light emitted from the plasma is focused to the entrance slit of a spectrometer and detected by an OMA III system. For every laser pulse an spectral range of 100 A are recorded. With the use of time-resolved spectroscopy a precision of 1.6 % and a detection limit of 65 ppm of carbon content in steel have been obtained. These values are similar to those of other accurate conventional techniques but using optics fiber and laser excitation it is possible to made sample calibrations in hostile environments. Also, as the analysis are made in real time changes in sample composition can be measured without stopping production processes. (Author) 26 refs

  10. Determination of the carbon content of domestic farm produces to estimate offsite C-14 ingestion dose

    International Nuclear Information System (INIS)

    Jung, Y. G.; Kim, M. J.; Lee, G. B.

    2003-01-01

    The carbon content of grains, leafy and root vegetables, and fruits which the Koreans usually eat were calculated to use in the estimation of offsite C-14 ingestion dose. With the data of food intake per day in the Report on 1998 national health and nutrition survey- dietary intake survey, 5 age-group integrate d intake of the 4 farm produce groups were extracted for food items and the amount. Intake percentage in each food group were taken as food weighing factor for the foods. Carbon content was calculated using protein, fat, and carbohydrate content of the foods, and multiplied by the corresponding food weighing factor to derive the content of the food groups. The calculated carbon content of grains, leafy and root vegetables, and fruits were 39.%, 4.2%, 8.0%, and 5.9% respectively. Grains and fruits were not much different from ODCM for carbon content, but vegetables were higher by 0.7%∼4.5%

  11. The Hydrogen Pickup Behavior for Zirconium-based Alloys in Various Out-of-pile Corrosion Test Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Aomi, M.; Etoh, Y.; Ishimoto, S.; Une, K. [Nippon Nuclear Fuel Development, Co., Ltd., 2163 Narita-cho, Oarai-machi, Ibaraki-ken, 311-1313 (Japan); Ito, K. [Global Nuclear Fuel Japan Co., Ltd., 3-1 Uchikawa 2-chome, Yokosuka-shi, Kanagawa-ken, 239-0836 (Japan)

    2009-06-15

    An acceleration of hydrogen absorption in zirconium alloy claddings at high burnups is one of the most important issues limiting the fuel performance from the viewpoint of cladding integrity. In this context, advanced cladding materials with higher corrosion resistant and lower hydrogen absorption properties have been widely searched in various organizations. In this study, four kinds of zirconium-based alloys, whose in-pile data had been acquired [1,2] were subjected to comprehensive out-of-pile corrosion tests with various temperature and atmosphere conditions in order to investigate the correlation between in-pile and out-of-pile corrosion and hydrogen pick-up behavior, i.e. Zry-2, GNF-Ziron (Zry-2-based alloy with {approx}0.25 wt % of Fe), Hi-FeNi Zircaloy (Zry-2-based alloy with {approx}0.25 wt % of Fe and {approx}0.1 wt% Ni), and VB (Zr-based alloy containing Sn, Cr, and {approx}0.5 wt % of Fe). All the alloys were annealed in RXA condition. The out-of-pile corrosion tests were carried out in three different conditions of 400 deg. C steam, 475 deg. C supercritical water, and 290 deg. C LiOH aqueous solution. In addition to these alloys, several Zry-2-based alloys with various iron contents were tested in 290 deg. C LiOH aqueous solution. Among the four corrosion conditions, the 290 deg. C LiOH aqueous solution test well screened the hydrogen pick-up behavior of the alloys. The hydrogen absorption decreased with higher iron contents in the alloys in both the out-of-pile and in-pile conditions. Especially, the distinct suppression of hydrogen absorption was observed for VB with the highest iron content. The similar dependence of iron content on the hydrogen pick-up fraction was also obtained for the Zry-2-based alloys with different iron contents, which were corroded in the 290 deg. C LiOH aqueous solution condition. As for the corrosion behavior in the 290 deg. C LiOH aqueous solution condition, the weight gains of Zry-2, GNF-Ziron and VB followed the 1

  12. How international oil and gas companies respond to local content policies in petroleum-producing developing countries: A narrative enquiry

    International Nuclear Information System (INIS)

    Ngoasong, Michael Zisuh

    2014-01-01

    This paper uses narrative analysis to critically examine the business practices used by five international oil and gas companies (IOCs) (Chevron, ExxonMobil, Shell, BP and Total) to respond to local content policies in petroleum-producing developing countries (Nigeria, Angola, Venezuela, Kazakhstan, Brazil, Indonesia, Yemen and Indonesia) during the period 2000–2012. The business practices include the formulation of local content strategies that are implemented through programmes and initiatives aimed at developing and using host country suppliers and workforce. Such practices and the narratives used to communicate them implicitly reflect the context in which the effectiveness of local content policies on economic development can be assessed. By comparing and contrasting the narratives across the five IOCs in relation to the wider literature, four emergent narrative strategies justifying the business practices of IOCs are identified and discussed. They include: (1) direct engagement to renegotiate local content requirements with governments, (2) legal compliance framework, (3) the business case for local content strategies, and (4) corporate social responsibility (CSR) initiatives. The conclusion considers the policy implications of these findings for local content development in petroleum-producing developing countries. - Highlights: • Local content policies define the local context that shape IOCs’ business practices. • Provides a narrative analysis of the business practices of IOCs in developing countries. • IOCs use four narrative strategies to relate their business practices to local content policies. • The business practices of IOCs can determine the effectiveness of local content policies

  13. The content and distribution of steryl ferulates in wheat produced in Japan.

    Science.gov (United States)

    Tsuzuki, Wakako; Mogushi, Hiroyuki; Kawahara, Shuji; Kotake-Nara, Eiichi; Komba, Shiro; Kanai, Yoshikazu; Yamada, Sumiyo; Horigane, Akira

    2017-03-01

    Oryzanol contained in rice bran is a complex mixture of steryl ferulates (SFs) with many identified health benefits. Recently, SF has been shown to exist in other cereals such as wheat, rye, and corn. In this study, SFs in several wheats produced in Japan were analyzed. For instance, SF content of whole wheat grain, Yumekaori (Japan) was 15.2 ± 1.4 mg-oryzanol-equivalent/100 g grain, while that of the imported one, 1CW (Canada) was 11.4 ± 1.3 mg-oryzanol-equivalent/100 g grain. The main SF components in the examined wheats were campesteryl ferulate, campestanyl ferulate, and sitostanyl ferulate. SF distribution in whole wheat grain was investigated using 14 fractions produced by a conventional test milling machine. SF was intensively accumulated in the four bran fractions (24 - 95 mg-oryzanol-equivalent/100 g bran fraction). These results suggest that the wheat bran would be an important source of SF.

  14. Sewage sludge based producer gas of rich H{sub 2} content as a fuel for an IC engine

    Energy Technology Data Exchange (ETDEWEB)

    Szwaja, Stanislaw; Cupial, Karol [Czestochowa Univ. of Technology (Poland)

    2010-07-01

    The manuscript presents investigation on hydrogen rich gas combustion in an internal combustion (IC) engine. The gas is obtained from gasification process of sewage sludge which is by-product of waste water treatment in a municipal sewage treatment plant. Recently introduced EU regulations of environmental protection do not allow to use such sludge as a soil fertilizer or substance for landfilling the ground due to its biological toxicity. On another hand, this sludge contains organic content of approximately 45-55% and from this point of view the sludge looks as an attractive material for fuel production through its gasification. This technology, primarily applied for wood gasification, has been also successfully implemented for gasification of sludge. It was found that the producer gas obtained in this way is rich of hydrogen content even up to 25%. This is because of high water content in the sludge that provides favorable conditions for steam reforming resulting in increase of hydrogen in the products of gasification. The high hydrogen content in the producer gas can lead to improper combustion particularly when the combustion takes place in the internal combustion engine. That improper combustion might appear as combustion knock and it is the main problem for the engine in which hydrogen is used as a fuel [1]. Onset of the knock during combustion contributes to rapid increase in heat transfer to the piston crown causing the piston to be quickly overheated that leads to surface erosion and damages. Additionally, engine body vibration coming from the knock significantly shortens engine durability. Conclusions from this investigation provide good premises for combusting the sludge producer gas in the IC engine without any improper combustion anomalies, thus considers this gas as worthy fuel for a stationary engine driven a power generator. The presentation shows results of producer gas combustion in both the spark-ignited and the compression ignition engine with

  15. The effects of moisture on LiD single crystals studied by temperature-programmed decomposition

    International Nuclear Information System (INIS)

    Dinh, L.N.; Cecala, C.M.; Leckey, J.H.; Balooch, M.

    2001-01-01

    Temperature-programmed decomposition (TPD) technique was performed on LiOH powders and LiD single crystals previously exposed to different moisture levels. Our results show that the LiOH decomposition process is rate-limited by an inward moving reaction front mechanism with an activation energy barrier of ∼122-149 kJ/mol. The LiOH structure is stable even if kept at 320 K. However, LiOH structures formed on the surface of LiD single crystals during moisture exposure at low dosages may have multiple activation energy barriers, some of which may be much lower than 122 kJ/mol. The rate-limiting mechanism for the decomposition of LiOH structures with reduced activation energy barriers is consistent with a unimolecular nucleation model. We attribute the lowering of the activation energy barrier for the LiOH decomposition to the existence of sub-stoichiometric Li(OH) x with x 2 O formation is observed. The release of H 2 O molecules from LiOH · H 2 O structure has small activation energy barriers in the range of 48-69 kJ/mol and follows a unimolecular nucleation process. The loosely bonded H 2 O molecules in the LiOH · H 2 O structure can be easily pumped away at room temperature in a reasonable amount of time. Our experiments also suggest that handling LiD single crystals at an elevated temperature of 340 K or more reduces the growth rate of LiOH and LiOH · H 2 O significantly

  16. Fabrication of Li{sub 4}SiO{sub 4} pebbles by gel-precipitation technology

    Energy Technology Data Exchange (ETDEWEB)

    Wen, Z.; Wu, X.; Gu, Z. [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai (China)

    2007-07-01

    Full text of publication follows: Lithium orthosilicate (Li{sub 4}SiO{sub 4}) is considered as a promising candidate as breeder material for fusion reactors due to its high lithium content, high stability and favorable tritium release behavior. The shape the breeder materials adopted was determined by many factors, such as the tritium breeding ratio, the ease of diffusion of tritium, the release of thermal stress and irradiation cracking etc. At present pebble configuration has been recognized as the preferred option in most blanket designs for tritium breeders. In the fabrication of spheres of a ceramic material, there are several methods available: the agglomeration of powders, melt-spraying method, sol-gel process and gel-precipitation process. Li{sub 4}SiO{sub 4} pebbles with satisfying quality have been fabricated by melt-spraying method. But expensive experimental equipment and high temperature restrict the extensive application of the method. Gel-precipitation can be operated at room temperature and no special equipment is needed. The technique has been successfully used to produce lithium aluminate ceramic spheres. In this work, fabrication of Li{sub 4}SiO{sub 4} pebbles by gel-precipitation technology was first time investigated systematically. LiOH, citric acid and SiO{sub 2} (aerosil) were used as raw materials. SiO{sub 2} (aerosil) was dispersed in the gel formed by LiOH and citric acid, milky suspension was then obtained and Li{sub 4}SiO{sub 4} pebbles were produced from the milky suspension. The pebbles obtained displayed pure Li{sub 4}SiO{sub 4} phase, exhibited high sphericity, uniform distribution in size, small amount of pores and cracks. Phase transformation with the molar ratio of SiO{sub 2}/LiOH was investigated. The effect of sintering temperature on microstructure was discussed. The water-based gel-precipitation method for fabrication of Li{sub 4}SiO{sub 4} spheres was simple and convenient to realize mass production. (authors)

  17. Perceived risks of produced water management and naturally occurring radioactive material content in North Dakota.

    Science.gov (United States)

    Torres, Luisa; Yadav, Om Prakash; Khan, Eakalak

    2017-07-01

    Unconventional oil and gas development using hydraulic fracturing has caused conflict and controversy across the globe including the U.S. where some States banned the practice. Nevertheless, North Dakota (ND) has supported the practice because the State perceives the risks to be acceptable and because it has brought growth and opportunities to small communities. However, social acceptance of new technology is based on a number of factors and not contingent on economic benefits. To date, no research has been conducted to understand public risk perception of hazards associated with produced water from hydraulic fracturing in ND. This study focuses on understanding the risk perception of select ND stakeholder groups regarding produced water management and naturally occurring radioactive material. The software Qualtrics was used to create an online survey, collect data, and perform statistical analysis. The most important variables that seem to influence risk perception are the images and thoughts associated with produced water, level of knowledge about produced water handling and content, and knowing how to proceed in case of a spill of produced water. Overall, social risk perception could be in alignment with actual technical risk if availability of objective information is improved. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. TiO2-SiO2 Coatings with a Low Content of AuNPs for Producing Self-Cleaning Building Materials

    Directory of Open Access Journals (Sweden)

    Manuel Luna

    2018-03-01

    Full Text Available The high pollution levels in our cities are producing a significant increase of dust on buildings. An application of photoactive coatings on building materials can produce buildings with self-cleaning surfaces. In this study, we have developed a simple sol-gel route for producing Au-TiO2/SiO2 photocatalysts with application on buildings. The gold nanoparticles (AuNPs improved the TiO2 photoactivity under solar radiation because they promoted absorption in the visible range. We varied the content of AuNPs in the sols under study, in order to investigate their effect on self-cleaning properties. The sols obtained were sprayed on a common building stone, producing coatings which adhere firmly to the stone and preserve their aesthetic qualities. We studied the decolourization efficiency of the photocatalysts under study against methylene blue and against soot (a real staining agent for buildings. Finally, we established that the coating with an intermediate Au content presented the best self-cleaning performance, due to the role played by its structure and texture on its photoactivity.

  19. Effect of sewage sludge content on gas quality and solid residues produced by cogasification in an updraft gasifier

    Energy Technology Data Exchange (ETDEWEB)

    Seggiani, Maurizia, E-mail: m.seggiani@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy); Puccini, Monica, E-mail: m.puccini@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy); Raggio, Giovanni, E-mail: g.raggio@tiscali.it [Italprogetti Engineering SPA, Lungarno Pacinotti, 59/A, 56020 San Romano (Pisa) (Italy); Vitolo, Sandra, E-mail: s.vitolo@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy)

    2012-10-15

    Highlights: Black-Right-Pointing-Pointer Cogasification of sewage sludge with wood pellets in updraft gasifier was analysed. Black-Right-Pointing-Pointer The effects of sewage sludge content on the gasification process were examined. Black-Right-Pointing-Pointer Sewage sludge addition up to 30 wt.% reduces moderately the process performance. Black-Right-Pointing-Pointer At high sewage sludge content slagging and clinker formation occurred. Black-Right-Pointing-Pointer Solid residues produced resulted acceptable at landfills for non-hazardous waste. - Abstract: In the present work, the gasification with air of dehydrated sewage sludge (SS) with 20 wt.% moisture mixed with conventional woody biomass was investigated using a pilot fixed-bed updraft gasifier. Attention was focused on the effect of the SS content on the gasification performance and on the environmental impact of the process. The results showed that it is possible to co-gasify SS with wood pellets (WPs) in updraft fixed-bed gasification installations. However, at high content of sewage sludge the gasification process can become instable because of the very high ash content and low ash fusion temperatures of SS. At an equivalent ratio of 0.25, compared with wood pellets gasification, the addition of sewage sludge led to a reduction of gas yield in favor of an increase of condensate production with consequent cold gas efficiency decrease. Low concentrations of dioxins/furans and PAHs were measured in the gas produced by SS gasification, well below the limiting values for the exhaust gaseous emissions. NH{sub 3}, HCl and HF contents were very low because most of these compounds were retained in the wet scrubber systems. On the other hand, high H{sub 2}S levels were measured due to high sulfur content of SS. Heavy metals supplied with the feedstocks were mostly retained in gasification solid residues. The leachability tests performed according to European regulations showed that metals leachability was

  20. Lipid content and cryotolerance of in vitro-produced bovine embryos treated with forskolin before vitrification

    Directory of Open Access Journals (Sweden)

    Melissa Meneghel

    Full Text Available ABSTRACT: The aim of the present study was to evaluate the intracytoplasmic lipid content, development and cryotolerance of in vitro-produced bovine embryos treated with different concentrations of forskolin before vitrification. Embryos were produced from abattoir-derived ovaries and allocated into four groups. In the treatment groups, forskolin was added to the in vitro culture medium on Day 6 and incubated for 24 hours in one of the following concentrations: 2.5μM (Forsk 2.5 group, 5.0μM (Forsk 5.0 group or 10.0μM (Forsk 10.0 group. Embryos from the control group were cultured without forskolin. On Day 7 of culture, the expanded blastocysts were stained with the lipophilic dye Sudan Black B for determination of the intracytoplasmic lipid content or were cryopreserved via the Vitri-Ingá® procedure. Although there were no significant differences (P>0.05 in the blastocyst rates between the Control group (44.9% and the other treatments, the embryo production was lower (P0.05 to that found in Forsk 2.5 (0.92±0.03 and Forsk 10.0 groups (1.06±0.03 groups; however the lipid accumulation in blastocysts from Forsk 5.0 group (0.82±0.04 was lower than in the Control group (P<0.05. Based on these results, Forsk 5.0 treatment was tested for cryotolerance and it was observed that the blastocoel re-expansion rate evaluated 24 hours after warming was greater (P<0.05 in Forsk 5.0 group (72.2% compared to the Control group (46.2%. In conclusion, pre-treatment with forskolin at a concentration of 5.0 μM for 24 hours before vitrification is effective in reducing the intracytoplasmic lipid content and, consequently, improves cryotolerance of IVP bovine embryos.

  1. Spectroscopic analysis of lithium hydroxide and carbonate in solid state lithium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Oohira, Shigeru; Fujii, Yasuhiko; Okamoto, Makoto; Kakihana, Masato; Nagumo, Tadashi

    1985-08-01

    Infrared spectra of LiOH and Li2CO3 suspended on KBr discs were measured over the concentration range 20 g/100 mg KBr to 600 g/100 mg KBr. The absorbance of a selected infrared band of each sample was carefully determined. The empirical equation, which expresses a correlation between the absorbance and the concentration, was given for each lithium compound. The feasibility of independent and direct determination of the LiOH and Li2CO3 content in Li2O was shown, and the spectroscopic technique was applied to a typical Li2O sample. It was shown that the detection limit of the analysis was improved by low-temperature measurements of the infrared spectra. (orig.).

  2. Relationship Between the Process Parameters and Resin Content of a Glass/Epoxy Prepreg Produced by Dipping Method

    Directory of Open Access Journals (Sweden)

    Hamid Reza Khalafi

    2015-02-01

    Full Text Available The properties of prepregs are characterized in terms of their volatile content, resin content, the degree of pre-cure, void content, tack and flow ability. Resin content is one of the most important properties of prepregs so that its changing will result in altered properties such as, tack and resin flow. In order to monitor the resin content, a quantitative relation to the processing parameters such as line speed, viscosity and distance between the resin up taking rollers have to be determined. In this study, a tri-axial E-glass fabric with the areal weight of 1025 g/m2 and an epoxy resin (Epon 828 were used to produce the prepreg by the dipping method. In the theoretical part of this work, the free coating is studied and as a result the thickness layer of the coating resin through the resin bath is calculated by Landau-Levich model. In continuation, the achieved thickness was considered as a feed for the calendering process. Using the momentum equation for the passing impregnated fibres through the extra resin uptake rollers, the relation between the internal resin layer thickness and final coating resin layer thickness was achieved in an integral equation form. In order to solve this integral equation, MAPLE software was applied. The theoretical results were in good agreement with the experimental data and showed that the resin content increased linearly with increasing the distance between rollers, the radius and roller angular velocity. In contrast, the resin content decreased with increasing the line speed. According to our calculations, the effect of the resin viscosity variation on the resin content was negligibly small.

  3. Root Cause Assessment of Pressure Drop Rise of a Packed Bed of Lithium Hydroxide in the International Space Station Trace Contaminant Control System

    Science.gov (United States)

    Aguilera, Tatiana; Perry, Jay L.

    2009-01-01

    The trace contaminant control system (TCCS) located in the International Space Station s (ISS) U.S. laboratory module employs physical adsorption, thermal catalytic oxidation, and chemical adsorption to remove trace chemical contamination produced by equipment offgassing and anthropogenic sources from the cabin atmosphere. The chemical adsorption stage, consisting of a packed bed of granular lithium hydroxide (LiOH), is located after the thermal catalytic oxidation stage and is designed to remove acid gas byproducts that may be formed in the upstream oxidation stage. While in service on board the ISS, the LiOH bed exhibited a change in flow resistance that leading to flow control difficulties in the TCCS. Post flight evaluation revealed LiOH granule size attrition among other changes. An experimental program was employed to investigate mechanisms hypothesized to contribute to the change in the packed bed s flow resistance. Background on the problem is summarized, including a discussion of likely mechanisms. The experimental program is described, results are presented, and implications for the future are discussed.

  4. Food Grade Grease Berbahan Baku Minyak Sawit Crude Palm Oil (Cpo Off Grade Dengan Variasi Konsentrasi Thickening

    Directory of Open Access Journals (Sweden)

    Martanto Totok

    2017-03-01

    Full Text Available Food grade grease (FGG is a kind of lubricant made from vegetable oil. Food Grease isconsidered safe for healthy and it does not pollute the environment so that it can be veryimportant for particular industries such as pharmaceutical, animal feeding, cosmetic, andespecially food industry. This study is aiming at obtaining optimum basic formulation ofthickening agent (LiOH that can produce qualified food grade grease. It is a kind of factorialexperimental study by using complete random sampling. Based on Fisher test, the treatmentshows a different result significantly. Then, it is continued by conducting Duncan’s MultipleRange Test (DMRT. 2% of activated charcoal is the best treatment because it results FFAscore, lower water content, and the bright yellow color that is shown by the score of 5.48%,0.0498 %, and 3 % that successively obtained. The treatment on thickening agent (LiOH(P1 and the revious one (L1 are the best treatment which produce qualified food gradegrease, corrosion resistance value 12.0, dropping point 130C, lubricating texture value 1,pH value 9.45, water content 0.19%, and ash content value 0.76%.

  5. Determination of Methanol Content in Herbal Distillates Produced in Urmia Using Spectrophotometry

    Directory of Open Access Journals (Sweden)

    Mohammad Delirrad

    2012-05-01

    Full Text Available Background: Herbal distillates have been used for many centuries as drinks, flavors, and herbal medicine in Iran, especially in the city of Urmia. Recently, some studies claimed the presence of methanol in different types of herbal distillates. Methanol is a highly toxic compound which can cause acute or chronic toxicity in humans. Acute poisoning with methanol can cause different complications and even death while chronic methanol exposure has a wide range of nonspecific and misleading findings. The main purpose of this study was to determine methanol content in the commonly-used industrial herbal distillates produced in Urmia. Methods: Five samples of six types of most commonly used herbal distillates (peppermint, musk willow, lemon balm, pennyroyal, dill, and rose water were purchased from five active herbal distillates manufacturers in Urmia. All samples were transferred to the laboratory and methanol content of each sample was measured two times according to the standard method of analysis using spectrophotometer. Results: The lowest and highest concentration of methanol were found in rose water (mean=72.4±32.1 ppm and musk willow (mean=278.3±106 ppm samples, respectively. One-way ANOVA showed statistically significant differences among methanol concentrations in the studied herbal distillates (F=60.9, P <0.001. Discussion: Different amounts of methanol were found in herbal distillates and it seems that there are statistically significant differences in methanol concentrations of various types of herbal distillates. Therefore, considering the harmful effects of methanol on human health, further studies are required for determining permitted levels of methanol in herbal distillates.

  6. Social media as a space for support: Young adults' perspectives on producing and consuming user-generated content about diabetes and mental health.

    Science.gov (United States)

    Fergie, Gillian; Hunt, Kate; Hilton, Shona

    2016-12-01

    Social media offer opportunities to both produce and consume content related to health experiences. However, people's social media practices are likely to be influenced by a range of individual, social and environmental factors. The aim of this qualitative study was to explore how engagement with user-generated content can support people with long-term health conditions, and what limits users' adoption of these technologies in the everyday experience of their health condition. Forty semi-structured interviews were conducted with young adults, aged between 18 and 30 years, with experience of diabetes or a common mental health disorder (CMHD). We found that the online activities of these young adults were diverse; they ranged from regular production and consumption ('prosumption') of health-related user-generated content to no engagement with such content. Our analysis suggested three main types of users: 'prosumers'; 'tacit consumers' and 'non-engagers'. A key determinant of participants' engagement with resources related to diabetes and CMHDs in the online environment was their offline experiences of support. Barriers to young adults' participation in online interaction, and sharing of content related to their health experiences, included concerns about compromising their presentation of identity and adherence to conventions about what content is most appropriate for specific social media spaces. Based on our analysis, we suggest that social media do not provide an unproblematic environment for engagement with health content and the generation of supportive networks. Rather, producing and consuming user-generated content is an activity embedded within individuals' specific health experiences and is impacted by offline contexts, as well as their daily engagement with, and expectations, of different social media platforms. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  7. Reaction of LiD with moisture by temperature programmed reaction (TPR)

    International Nuclear Information System (INIS)

    Dinh, L N; Balooch, M; Cecala, C M; Leckey, J H

    2000-01-01

    The temperature programmed reaction technique was performed on LiOH powders and LiD single crystals previously exposed to different moisture levels. Our results show that the LiOH decomposition process has an activation energy barrier of 30 to 33.1 kcal/mol. The LiOH structure is stable at 320 K for 100 years. However, LiOH structures formed on the surface of LiD during moisture exposure at low dosages may have multiple activation energy barriers, some of which may be much lower than 30 kcal/mol. We attribute the lowering of the activation energy barrier for the LiOH decomposition to the existence of dangling bonds, cracks, and other long range disorders in the LiOH structures formed at low levels of moisture exposure. These defective LiOH structures may decompose significantly over the next 100 years of storage even at room temperature. At high moisture exposure levels, LiOH.H 2 O formation is observed. The release of H 2 O molecules from LiOH.H 2 O structure has small activation energy barriers in the range of 13.8 kcal/mol to 16.0 kcal/mol. The loosely bonded H 2 O molecules in the LiOH.H 2 O structure can be easily pumped away at room temperature in a reasonable amount of time. Our experiments also suggest that handling LiD single crystals at an elevated temperature of 340 K or more reduces the growth of LiOH and LiOH.H 2 O significantly

  8. Fertilization effect on yield and nitrate content in organically produced lettuce

    Directory of Open Access Journals (Sweden)

    Čabilovski Ranko

    2010-01-01

    Full Text Available The effect of applying different organic materials (OM on yield and nitrate content in lettuce was studied in a field experiment on a farm registered for organic production during two years (2007 and 2008. Treatments were: farmyard manure (ST, guano (G, milled soybean (Glicine hispida seed (S; milled forage pea (Pisum sativum seed (P and control treatment (q. Biannual average fresh matter (FM yield of lettuce on fertilized plots ranges from 45.44 t ha-1 (P to 46,38 t ha-1 (ST and was significantly higher than fresh matter yield of the control (39.34 t ha-1, while the differences between fertilized treatments were not significant. Nitrate content in the fresh mass of lettuce in all treatments in both years was below the maximum allowed content (2.500 mg kg-1 regulated by the EU (Commission Regulation (EC, No 466/2001. In both years, the lowest nitrate content in the fresh mass of lettuce was recorded with the control treatment (q and highest with S treatment. Nitrate contents with G, P and S treatments were significantly higher than that recorded with FYM and q, whereas the differences between FYM and q were not significant in either the first or the second year of research. Linear correlation (r = 0.83**in 2007; r = 0.91** in 2008 was found between the content of mineral N in the soil and nitrate content in the FM of lettuce at the moment of harvesting in both years. .

  9. New kinetic insight into the spontaneous oxidation process of lithium in air by EPMA

    Energy Technology Data Exchange (ETDEWEB)

    Otero, Manuel [IFEG, Facultad de Matemáticas, Astronomía y Física, Universidad Nacional de Córdoba, Córdoba (Argentina); INFICQ, Departamento de Matemáticas y Física, Facultad de Ciencias Químicas, Universidad Nacional de Córdoba, Córdoba (Argentina); Lener, German [INFAP, Facultad de Ciencias Físico Matemáticas y Naturales, Universidad Nacional de San Luis, San Luis (Argentina); Trincavelli, Jorge, E-mail: trincavelli@famaf.unc.edu.ar [IFEG, Facultad de Matemáticas, Astronomía y Física, Universidad Nacional de Córdoba, Córdoba (Argentina); Barraco, Daniel [IFEG, Facultad de Matemáticas, Astronomía y Física, Universidad Nacional de Córdoba, Córdoba (Argentina); Nazzarro, Marcelo Sandro; Furlong, Octavio [INFAP, Facultad de Ciencias Físico Matemáticas y Naturales, Universidad Nacional de San Luis, San Luis (Argentina); Leiva, Ezequiel Pedro Marcos [INFICQ, Departamento de Matemáticas y Física, Facultad de Ciencias Químicas, Universidad Nacional de Córdoba, Córdoba (Argentina)

    2016-10-15

    Highlights: • EPMA measurements and Monte Carlo simulations were applied to study the corrosion process of Li in air. • The kinetic mechanism of corrosion was discussed. • A diffusion process of water through LiOH was found and quantitatively studied. - Abstract: The exposure of metallic lithium to ambient air produces a fast corrosion reaction of the surface that continues to the bulk of the material. This spontaneous process was explored by means of X-ray Photoelectron Spectroscopy (XPS) and Electron Probe Micro-Analysis (EPMA). The combination of these techniques and Monte Carlo simulations allowed observing the formation of a film of lithium hydroxide (LiOH) and studying the growth within the material during the first 300 s. The corrosion is mainly due to the reaction of lithium with water and the diffusion of water through the growing LiOH film is the rate determining step. On the basis of a kinetic analysis we studied the mechanism of reaction and inferred a diffusion coefficient of D = (5.1 ± 0.4) × 10{sup −12} cm{sup 2}/s in agreement with results from the literature obtained using different techniques.

  10. Study On Analytical Methods Of Tellurium Content In Natriiodide (Na131I) Radiopharmaceutical Solution Produced In The Dalat Nuclear Reactor

    International Nuclear Information System (INIS)

    Vo Thi Cam Hoa; Duong Van Dong; Nguyen Thi Thu; Chu Van Khoa

    2007-01-01

    This report describes the practical methods for analyzing of Tellurium content in Na 131 I solution produced at the Dalat Nuclear Research Institute. We studied analytical methods to control Tellurium content in final Na 131 I solution product used in medical purposes by three methods such as: spot test, gamma spectrometric and spectrophotometric methods. These investigation results are shown that the spot test method is suitable for controlling Tellurium trace in the final product. This spot test can be determinate Tellurium trace less than 10 ppm and are used to quality control of Na 131 I solution using in medical application. (author)

  11. Carbon content and C:N ratio of transparent exopolymeric particles (TEP) produced by bubbling exudates of diatoms

    DEFF Research Database (Denmark)

    Mari, Xavier

    1999-01-01

    The carbon content of transparent exopolymeric particles (TEP) was measured in the laboratory in particles produced by bubbling exudates of the diatom Thalassiosira weissflogii, grown under nitrogen non-limited conditions (N:P = 7). The carbon content of these particles (TEP-C) appears to vary...... a coastal area (Kattegat, Denmark), TEP carbon concentration in the surface mixed layer was on the order of 230 ± 150 µg C l-1. This is high relative to other sources of particulate organic carbon (e.g. phytoplankton) and depending on TEP turnover rates, suggests that TEP is an important pathway...... for dissolved organic carbon in coastal seas. The carbon to nitrogen ratio of TEP was measured from particles formed by bubbling exudates of the diatoms T. weissflogii, Skeletonema costatum, Chaetoceros neogracile and C. affinis. Each of these diatom species was grown under various N:P ratios, from N...

  12. MONITORING OF A GLUTEN CONTENT IN SELECTED MEAT PRODUCTS FROM THREE BIGGEST MEAT PRODUCERS IN SLOVAKIA

    Directory of Open Access Journals (Sweden)

    Ladislav Staruch

    2012-02-01

    Full Text Available The work is focused on a monitoring of a gluten content in selected meat products from three biggest and most popular meat producers in Slovakia. Gluten is a type of protein complex which is typical naturally presented component of wheat, barley and rye. Flour from this sources with natural gluten content is also added into the some type of meat products and other foodstuffs for a technological reasons hand in hand with economic reasons.  Some of the gluten quantities could be hazardous for sensitive people as celiatics and allergic to gluten. Within the context of this reasons there is a need to control the amounts of this hidden type of gluten inclusive of spice mixes using in a meat production. Monitoring by itself was realized with a use of the sandwich ELISA RIDASCREEN® Fast Gliadin test. ELISA means enzyme linked immunosorbent assay. It is based on a specific reaction among the enzyme and antigen leading to a creation of a complex.  This test provides us exact quantitification of a gluten content in this type of food products using a colorimetric reaction of a complex by observing of all fundamentals of this technique. There were analysed 16 meat products and 5 types of spice mixes in total.doi:10.5219/167

  13. Determination of water, hydrogen, and carbon content of Korean main farm produces for the calculation of H-3 and C-14 ingestion dose

    International Nuclear Information System (INIS)

    Chung, Yang Geun; Lee, Gab Bock; Kim, Mi Ja; Eum, Hee Moon

    2003-01-01

    Water, hydrogen, and carbon content of grains, leafy vegetable, root vegetable, and fruits in Korea were determined to be used in the calculation of HTO, OBT, C-14 offsite ingestion dose. The individual items and the weighting factors of the 4 groups were based on the results of nationwide dietary intake survey in Korea. Items produced in an island or imported were excluded for the reason that they would not be affected directly by the nuclear power plants in the nation. On the same assumption, cooked and instant foods also were excluded. Items within 95% of the cumulative percentage of intake in each category were selected as the main farm produces, and then each intake percentage was taken as the weighting factor. Water, Hydrogen, and carbon content were determined using the data in Food Composition TABLE of Korea. H and C content were calculated from protein, fat, and carbohydrate content in the TABLE, and multiplied by each weighting factor to make the group-representative value. Grains, lefty and root vegetable, and fruits of Korea had 11.0%, 93.6%, 87.9%, 86.2% of water, 5.6%, 0.4%. 0.7%, 0.9% of hydrogen, and 39.6%, 2.5%, 5.2%, 6.0% of carbon, respectively. This is different from those in the ODCM from AECL data. Over ODCM, water content of grains and vegetable were 0.92-0.98 times ODCM, and fruits 1.03 times ODCM, which would result in the change of HTO ingestion dose as much. Hydrogen content of grains and vegetables are 1.02-2.33 times ODCM, but fruits 0.9 times ODCM. Carbon content of grains, leafy vegetables, and fruits are 0.7-0.98 times ODCM, but root vegetables 1.49 times ODCM. This would result in the change of ingestion dose as much

  14. Heavy metal (Pb, Cu, Zn and Cd content in wine produced from grape cultivar Mavrud, grown in an industrially polluted region

    Directory of Open Access Journals (Sweden)

    Violina Angelova

    1999-09-01

    Full Text Available The investigation was carried out in the period 1991-1993 with cv. Mavrud, grown in the region with a major industrial pollutant the Non-Ferrous-Metal Works (NFMW and a region with no industrial pollutants (as a control. The heavy metal content in soil, grapes and wine was determined. Most of the heavy metals in the grapes precipitate during fermentation into the sediments, which is the reason for their significantly lower content in the wine. Water washing of grape before processing leads to about 2 time decrease in the Pb, Cu, Zn and Cd contents of wine. The pre-washing of grapes does not lead to any quality deterioration in the wine produced. The amounts of Cu, Zn and Cd in the wine from cv. Mavrud, grown in the region of the NFMW-Plovdiv, are lower than the maximum admissible levels, while the Pb content exceeds them about two times.

  15. Determining the water cut and water salinity in an oil-water flowstream by measuring the sulfur content of the produced oil

    International Nuclear Information System (INIS)

    Smith, H.D.; Arnold, D.M.

    1980-01-01

    A technique for detecting water cut and water salinity in an oil/water flowstream in petroleum refining and producing operations is described. The fluid is bombarded with fast neutrons which are slowed down and then captured producing gamma spectra characteristic of the fluid material. Analysis of the spectra indicates the relative presence of the elements sulfur, hydrogen and chlorine and from the sulfur measurement, the oil cut (fractional oil content) of the fluid is determined, enabling the water cut to be found. From the water cut, water salinity can also be determined. (U.K.)

  16. Evaluation of Cadmium, Lead and Zinc Content of Compost Produced in Babol Composting Plant

    Directory of Open Access Journals (Sweden)

    Fatemeh Asgharzadeh

    2014-03-01

    Full Text Available Background and purpose: The most important parameter is heavy metal contents in compost production technology. These heavy metals residue from substances like soap, detergents, cosmetics, packaging, leather and butteries are existed in municipal solid waste. The heavy metals can produce toxin for animal, human and plant. The aim of this research was study of produced compost quality based on heavy metals (Pb, Cd and Zn in Babol compost plant in 2012. Materials and Methods: The present research is a descriptive- cross sectional study in which was performed in six months. Total sample numbers (5 samples were randomly provided from final compost of Babol plant and then after extraction and filtration, the concentration of heavy metals like cadmium, lead and zinc was measured by atomic absorption spectrophotometer PG- 999. Results: In analyzed samples the maximum, minimum and average of cadmium in the final compost were 7.25, 0.47 and 1.9 mg/kg. The maximum, minimum and mean of lead were 239.2, 31.9 and 67.1 mg/kg; in zinc were 972.7, 483.5 and 603.7 mg/kg respectively. Conclusion: The concentration of heavy metals in Babol compost samples was under Iranian national and World Health Organization standards and could be used for different species of plants. However, the usability of compost depends on other parameters such as carbon to nitrogen and other components like glass, plastics and textiles.

  17. SIMS and TEM study on oxide characteristics of Zircaloy

    International Nuclear Information System (INIS)

    Jung, Y. H.; Baek, J. H.; Kim, S. J.; Kim, K. H.; Choi, B. K.; Jung, Y. H.

    1998-01-01

    Long-term corrosion test, SIMS analysis, and TEM study were carried out to investigate the corrosion characteristics and corrosion mechanism of Zircaloy-4 in LiOH solution. The corrosion tests were performed in alkali solutions at 350 deg C for 500days. SIMS analysis was performed for the specimens prepared to have an equal oxide thickness to measure the cation content. TEM studies on the samples formed in various alkali solutions were also conducted. Based on the corrosion test, SIMS analysis, and TEM study, the cation is considered to control the corrosion in LiOH solution and its effect is dependent on the concentration of alkali and the oxide thickness. The slight acceleration of corrosion rate at a low concentration is thought to be caused by the cation incorporation into oxide while the significant acceleration at a high concentration is due to the transformation of oxide microstructure that would be induced by the cation incorporation

  18. Web content a writer's guide

    CERN Document Server

    Mizrahi, Janet

    2013-01-01

    The explosion of electronic sources, whether in the form of news, commentary, sales and marketing, or information, has created boundless opportunities for producing content. Whether you're an entrepreneur with a start-up business who needs a website, an executive who uses social media to connect with various stakeholders, or a content provider blogging about topical issues, you'll need to know how to write for the web and address the unique environment of the digital world. This book will help you produce web content that generates results. Writing for the screen differs from writing for a pri

  19. Lithium uptake and the accelerated corrosion of zirconium alloys

    International Nuclear Information System (INIS)

    Ramasubramanian, N.; Precoanin, N.; Ling, V.C.

    1989-01-01

    The corrosion of zirconium alloys in aqueous lithiated solutions is sensitive to the concentration of the alkali and the temperature. In concentrated solutions, >10 -1 M in lithium hydroxide (LiOH) (700-ppm lithium) and at temperatures >573 K, accelerated corrosion occurs at quite an early stage. Our investigations indicate that the accelerated corrosion is caused by the generation of porosity, rather than the dissolution of lithium, in the growing oxide. Specimens of standard Zircaloy-4 fuel cladding and Zr-2.5 wt% Nb pressure tube materials were corroded in lithium hydroxide solutions, 10 -3 to 1 M in concentration, at 589 K. Impedance measurements, polarizations in molten lithium nitrate-lithium hydroxide (LiNO 3 -LiOH) and scanning electron microscopy of the alloy-oxide interface indicated a high level of porosity, right from the initial stages, for oxide films grown in the concentrated solutions. The oxides, when analyzed by atomic absorption spectroscopy, revealed the presence of a few 100 ppm of lithium, too small to account for the accelerated corrosion by a mechanism of solid solution of lithium in zirconia. X-ray powder patterns of the oxides showed peaks for only monoclinic zirconia, but occasionally peaks for LiOH · H 2 O and LiOH were also observed. The counts for lithium, detected by secondary ion mass spectrometry, decreased when specimens cut from the same corroded samples were leached in nitric acid. It is concluded from these observations that a major part of lithium is physically held in the porous oxide. Lithium hydroxide is not completely dissociated in aqueous solutions; with increasing concentration and temperature, an increasingly larger proportion of the alkali remains undissociated. It is suggested that the accelerated corrosion in concentrated solutions is caused by the participation of the undissociated alkali in the reactions occurring on the surfaces of the zirconia crystallites. The undissociated LiOH and hydroxyl ions react at an

  20. Characterization of Briquette Produced from Tannery Solid Waste

    Directory of Open Access Journals (Sweden)

    Olatunde Ajani Oyelaran

    2017-06-01

    Full Text Available Skin processing produces large volumes of wastes, much of which are not utilized but disposed in the landfill. This study explored the possibility of producing briquettes from tannery waste that could be used for heating purposes for cottage factories and domestic cooking. Wastes studied are buffing dust, chrome shavings, fleshing, and hair. The briquette properties tested were moisture content, volatile matter, ash content, fixed carbon content, calorific value, compressive strength, density and durability. The moisture content of the raw materials ranged between 2.04 and 8.37% while the moisture content of the produced briquettes after 19 days of drying ranges between 1.17 and 4.13%. The volatile matter also decreases while the ash content increases after briquetting. The fixed carbon content ranges 73.79 and 93.23%. The heating values of the briquettes also showed a great increased after briquetting of between 19.82 and 21.86 MJ/kg. The compressive strength ranges between 0.17 and 0.21 kN/cm2, the durability ranges between 97.83 and 99.54%. The maximum densities of the briquettes also meet the required specifications of minimum value of 600 kg/m3. The briquettes produced also possess good qualities that make tannery solid waste a materials for production of briquettes for heating and in cottage industries

  1. Hot temperature corrosion of a zircon-1%niobium alloy

    International Nuclear Information System (INIS)

    Muller, Sebastian; Lanzani, Liliana

    2010-01-01

    The reaction of the Zr-1%Niobium alloy to corrosion is studied in this work, which is used as fuel elements sheath material in Russian VVER reactors. For comparative purposes, the conventional alloys Zircaloy-4 y Zr-2.5%Nb have been tested as well. Autoclave tests were carried out in water and in solutions of LiOH with concentrations of 0-1 to 1M at 343 o C and in water vapor at 400 o C (following ASTM G2/G2M-06). The gain in weight/unit of area of the autoclaved samples was determined in order to evaluate the corrosion, and metallographics were performed to characterize the oxides and hydrides that formed. The results show that for tests of 16 hours, a minimum concentration of 0.65M LiOH is needed to accelerate corrosion in Zr-1%Nb and Zr-2.5%Nb, while acceleration occurs in Zircaloy-4 at a concentration of 0.45M. In solutions of LiOH 1M the hydrogen 'uptake' in Zr-1Nb and Zr-2,5Nb is considerably lower in Zircaloy-4. The lesser amount of β-Zr phase present in the Zr-1Nb alloy produces thinner and more compact oxides, with better visual characteristics than for those formed in Zr-2.5Nb

  2. Content Marketing Practices in Finland

    OpenAIRE

    Suuronen, Toni

    2016-01-01

    The purpose of this study is to draw attention to increasingly important business phenomenon of content marketing. This paper defines content marketing, identifies its key elements and phases, and explores content marketing practices. The theorethical part is based on Pam Didner's 4P model that describes the stages of content marketing cycle: plan, produce, promote and perfect. The empirical part of the study is based on semi-structured interviews of seasoned content marketing professionals t...

  3. The cadmium and lead content of the grain produced by leading Chinese rice cultivars.

    Science.gov (United States)

    Xie, L H; Tang, S Q; Wei, X J; Shao, G N; Jiao, G A; Sheng, Z H; Luo, J; Hu, P S

    2017-02-15

    The cadmium (Cd) and lead (Pb) content in both white and wholemeal flour milled from 110 leading rice cultivars was assessed. The white flour Cd content ranged from <0.0025 to 0.2530mg/kg (geometric mean (GM)=0.0150mg/kg), while its Pb content ranged from <0.0250 to 0.3830mg/kg (GM=0.0210mg/kg). The indica types took up higher amounts of Cd and Pb than did the japonica types. Although the heavy metal content of wholemeal flour tended to higher than that of white flour, nevertheless 84.5% (Cd) and 95.4% (Pb) of the entries were compliant with the national maximum allowable concentration of 0.2000mg/kg of each contaminant. An analysis of the Cd content in the white flour of three indica type cultivars grown in two consecutive years at two locations indicated that Cd content may be significantly affected by the conditions prevailing in the growing season. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Measurement of thorium content in gas mantles produced in India

    Energy Technology Data Exchange (ETDEWEB)

    Gaur, P K [Bhabha Atomic Research Centre, Mumbai (India). Radiological Physics Div.; Chury, A J; Venkataraman, G [Bhabha Atomic Research Centre, Mumbai (India). Radiation Protection Services Div.

    1994-04-01

    Incandescent gas mantles, processed with thorium nitrate, were monitored for thorium content, using a 2 inch thick Nal(Tl) detector and detecting medium energy gamma radiations emitted by thorium daughters. Thirty different brands, manufactured in the country have been counted and most of them were found to contain thorium within the permissible limit specified by Atomic Energy Regulatory Board (AERB). (author). 5 refs., 1 fig., 3 tabs.

  5. Corrosion behavior of Zr-x(Nb, Sn and Cu) binary alloys

    International Nuclear Information System (INIS)

    Kim, M. H.; Lee, M. H.; Park, S. Y.; Jung, Y. H.; We, M. Y.

    1999-01-01

    For the development of advanced zirconium alloys for nuclear fuel cladding, the corrosion behaviors of zirconium binary alloys were studied on the Zr-xNb, Zr-xSn, and Zr-xCu alloys. The corrosion test were performed in water at 360 deg C, steam at 400 deg C and LiOH at 360 deg C for 45 days. The corrosion behaviors of Zr-xNb was similar to that of Zr-xCu alloys. However, the corrosion behavior of Zr-xSn was different from Zr-xNb and Zr-xCu. The weight gain of Zr-xNb and Zr-xCu was increased with addition of alloying elements. When Sn is added to Zr matrix in range below the solubility limit, the corrosion resistance decrease with increasing Sn-content, while in the range over solubility limit, Sn has an adverse effect on the corrosion resistance. Especially, Zr-xSn alloys showed higher corrosion resistance than Zr-xNb and Zr-xCu alloys in LiOH solution

  6. Development of a chemically defined platform fed-batch culture media for monoclonal antibody-producing CHO cell lines with optimized choline content.

    Science.gov (United States)

    Kuwae, Shinobu; Miyakawa, Ichiko; Doi, Tomohiro

    2018-01-11

    A chemically defined platform basal medium and feed media were developed using a single Chinese hamster ovary (CHO) cell line that produces a monoclonal antibody (mAb). Cell line A, which showed a peak viable cell density of 5.9 × 10 6  cells/mL and a final mAb titer of 0.5 g/L in batch culture, was selected for the platform media development. Stoichiometrically balanced feed media were developed using glucose as an indicator of cell metabolism to determine the feed rates of all other nutrients. A fed-batch culture of cell line A using the platform fed-batch medium yielded a 6.4 g/L mAb titer, which was 12-fold higher than that of the batch culture. To examine the applicability of the platform basal medium and feed media, three other cell lines (A16, B, and C) that produce mAbs were cultured using the platform fed-batch medium, and they yielded mAb titers of 8.4, 3.3, and 6.2 g/L, respectively. The peak viable cell densities of the three cell lines ranged from 1.3 × 10 7 to 1.8 × 10 7  cells/mL. These results show that the nutritionally balanced fed-batch medium and feeds worked well for other cell lines. During the medium development, we found that choline limitation caused a lower cell viability, a lower mAb titer, a higher mAb aggregate content, and a higher mannose-5 content. The optimal choline chloride to glucose ratio for the CHO cell fed-batch culture was determined. Our platform basal medium and feed media will shorten the medium-development time for mAb-producing cell lines.

  7. Influence of microstructure on the accelerated corrosion in Zr-Nb alloys

    International Nuclear Information System (INIS)

    Muller, S; Lanzani, L

    2012-01-01

    The influence of microstructure on the accelerated corrosion of Zr-1%Nb and Zr-2.5%Nb (CANDU's pressure tube material) has been studied. The behavior of Zircaloy-4 was also studied in order to compare the Zr-Nb alloys with an alloy that does not have niobium as an alloying element. The corrosion tests were carried out in LiOH 0.1M at 340 o C, in LiOH 1M at the same temperature and in steam at 400 o C. The results showed that the behavior of Zr-Nb alloys in steam at 400 o C is similar to that of Zircaloy-4 in this medium. However, Zr-Nb alloys are more sensitive than Zircaloy-4 to the presence of LiOH. The results suggest that the niobium concentration in the matrix is the parameter that defines the oxidation rate in Zr-Nb alloys, while the presence of second phases in these alloys (β--Zr/β-Nb/Zr-Nb-Fe) could be related with the growth of non-protective oxides in LiOH solutions. In LiOH 1M, the corrosion resistance of Zr-Nb alloys is similar to that of Zircaloy-4, except for the Zr-1Nb martensitic material which showed a sharp increase in the oxidation rate in this medium (author)

  8. Electrochemical corrosion of Zircaloy-2 under PWR water chemistry but at room temperature

    International Nuclear Information System (INIS)

    Waheed, Abdel-Aziz Fahmy; Kandil, Abdel-Hakim Taha; Hamed, Hani M.

    2016-01-01

    Highlights: • There is no simple relation between the corrosion rate and LiOH concentration. • At low concentration, 100 ppm Li, an increase of the rate is due to the pH impact. • LiOH in concentrated solution led to accelerated corrosion by pH effect and porosity. • Boron abates the lithium effect by pH neutralizing and participation in the corrosion. - Abstract: Electrochemical corrosion of Zircaloy-2 was tested at room temperature in lithium hydroxide (LiOH) concentrations that ranged from 2.2 to 7000 ppm and boric acid (H 3 BO 3 ) concentrations that ranged from 50 to 4000 ppm. Following the corrosion experiments, the oxide films of specimens were examined by SEM to examine the oxide existence. LiOH concentrations as high as 1 M (7000-ppm lithium) can lead to significantly increased electrochemical corrosion rate. It is suggested that the accelerated corrosion in concentrated solution is caused by the synergetic effect of LiOH, pH and porosity generation. In solutions containing 100 ppm of lithium, the presence of boron had an ameliorating effect on the corrosion rates of Zircaloy-2. Similar to acceleration of corrosion by lithium, the inhibition by boron is due to a combined effect of pH neutralizing and its participation in the corrosion process.

  9. Examinations of content of heavy metals in municipal solid waste and produced compost

    International Nuclear Information System (INIS)

    Golimowski, J.; Tykarska, A.; Orzechowska, K.

    1993-01-01

    The basic methods of utilization of municipal solid waste are biothermic and aerobic methods to compost. The content of heavy metals in composts depends on the initial their content in wastes as well as on the compost process. The voltammetric method has been applied for measurement of concentration of Zn, Cd, Pb, Cu, Cr, Ni and Hg in the waste and composts samples. (author). 24 refs, 2 figs, 3 tabs

  10. Examination of the selenium content of wheat grasses produced in different soil types in Csik Basin

    Directory of Open Access Journals (Sweden)

    Tamás M.

    2015-01-01

    Full Text Available In the course of the research, we determined selenium and dry matter content of 35 wheat grass and 35 wheat seed samples. The selenium content of the preparation plant probes was measured by spectrofluorimetric determination (λexcitation = 380 nm, λemission = 519 nm of the resulted piazselenol complex. It was established that between the selenium content of the wheat grass and wheat seed the correlation coefficient was 0.36 at p = 0.05 level, which indicates a medium-close correlation. Similarly, there was a medium-close correlation between the selenium content of the wheat grass calculated on dry-matter basis and total selenium content of the wheat, with a correlation coefficient of 0.40 at p = 0.02 level. Afterwards, beside the selenium content, we measured the selenomethionine content by ion-exchange chromatography and highperformance liquid chromatography, and the organic selenium content was calculated. A very close correlation was established between the total selenium, selenomethionine and calculated organic selenium content of wheat (the correlation coefficients were between 0.92 and 0.99 at p = 0.01 level. The correlation between the selenomethionine content of wheat grass and wheat seed was very weak (r = 0.23.

  11. Effects of the inoculations using bacteria producing ACC deaminase on ethylene metabolism and growth of wheat grown under different soil water contents.

    Science.gov (United States)

    Zhang, Guozhuang; Sun, Yonglin; Sheng, Hao; Li, Haichao; Liu, Xiping

    2018-04-01

    Crop growth and productivity are often impacted by the increased ethylene content induced by adverse environmental conditions such drought. Inoculations with bacteria producing ACC deaminase is considered as a potential biological approach to improve the growth and tolerance of stressed plants by lowering endogenous ethylene level. In this study, germinated wheat seeds were inoculated using three species of the rhizobacteria, which were isolated from the rhizosphere of wheat growing in dryland, and sown in pots. After three weeks, wheat seedlings were exposed to non-limiting water condition, medium drought and severe drought, respectively, for six weeks. The results showed that, irrespective of rhizobacterial inoculations, decreased soil water contents stimulated wheat ethylene metabolism, which was reflected by the significantly increased activity of ACC synthetase and ACC oxidase, besides an increased content of ACC both in the roots and leaves, and an enhanced capacity of leaves to release ethylene, concomitant with a significant decline in shoot and roots biomass. The inoculations of all three rhizobacterial species under each water condition reduced ACC content in wheat leaves, but effects of the inoculations on ACC synthase and ACC oxidase activity in the leaves and roots, ACC content in the roots, the capacity of leaves to release ethylene, and wheat growth varied with water conditions and bacterial species. Hence, both soil water conditions and rhizobacterial inoculations acted on all the processes of ethylene metabolism, with the former being dominant. The inoculations under non-limiting water condition and medium drought promoted shoot and root growth of wheat plants. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

  12. Effect of air humidity on microstructure and phase composition of lithium deuteride corrosion products

    International Nuclear Information System (INIS)

    Liu, Xiaobo; Liu, Jiping

    2017-01-01

    Highlights: • Lithium deuteride samples are corroded by air with different relative humidity. • Show the structure and composition of fracture surface of corrosion particle. • The lithium carbonate formation is related to air humidity. • The lithium carbonate only exists in the surface of lithium hydroxide layer. • There is a concentration gradient of H 2 O across the lithium hydroxide layer. - Abstract: Lithium deuteride (LiD) was exposed to air for 600 min to determine the effect of air humidity on its microstructure and phase composition. XRD and XPS results revealed that LiOH and Li 2 CO 3 formed at relative humidity values of >30%, whereas only LiOH formed at values <20%. SEM and EDS images showed a clear LiOH layer; Li 2 CO 3 was confined to the surface of this layer. The schematic illustration revealed that the concentration gradient of H 2 O across the LiOH layer resulted in little Li 2 CO 3 formed in the layer. This work will contribute to increase understanding of LiD corrosion in air.

  13. Fuel burn-up distribution and transuranic nuclide contents produced at the first cycle operation of AP1000

    International Nuclear Information System (INIS)

    Jati Susilo; Jupiter Sitorus Pane

    2016-01-01

    AP1000 reactor core was designed with nominal power of 1154 MWe (3415 MWth), operated within life time of 60 years and cycle length of 18 months. For the first cycle, the AP1000 core uses three kinds of UO 2 enrichment, they are 2.35 w/o, 3.40 w/o and 4.45 w/o. Absorber materials such as ZrB 2 , Pyrex and Boron solution are used to compensate the excess reactivity at the beginning of cycle. In the core, U-235 fuels are burned by fission reaction and produce energy, fission products and new neutron. Because of the U-238 neutron absorption reaction, the high level radioactive waste of heavy nuclide transuranic such as Pu, Am, Cm and Np are also generated. They have a very long half life. The purpose of this study is to evaluate the result of fuel burn-up distribution and heavy nuclide transuranic contents produced by AP1000 at the end of first cycle operation (EOFC). Calculation of ¼ part of the AP1000 core in the 2 dimensional model has been done using SRAC2006 code with the module of COREBN/HIST. The input data called the table of macroscopic cross section, is calculated using module of PIJ. The result shows that the maximum fuel assembly (FA) burn-up is 27.04 GWD/MTU, that is still lower than allowed maximum burn-up of 62 GWD/MTU. Fuel loading position at the center/middle of the core will produce bigger burn-up and transuranic nuclide than one at the edges the of the core. The use of IFBA fuel just give a small effect to lessen the fuel burn-up and transuranic nuclide production. (author)

  14. Yield and properties of ethanol biofuel produced from different whole cassava flours.

    Science.gov (United States)

    Ademiluyi, F T; Mepba, H D

    2013-01-01

    The yield and properties of ethanol biofuel produced from five different whole cassava flours were investigated. Ethanol was produced from five different whole cassava flours. The effect of quantity of yeast on ethanol yield, effect of whole cassava flour to acid and mineralized media ratio on the yield of ethanol produced, and the physical properties of ethanol produced from different cassava were investigated. Physical properties such as distillation range, density, viscosity, and flash point of ethanol produced differ slightly for different cultivars, while the yield of ethanol and electrical conductivity of ethanol from the different cassava cultivars varies significantly. The variation in mineral composition of the different whole cassava flours could also lead to variation in the electrical conductivity of ethanol produced from the different cassava cultivars. The differences in ethanol yield are attributed to differences in starch content, protein content, and dry matter of cassava cultivars. High yield of ethanol from whole cassava flour is best produced from cultivars with high starch content, low protein content, and low fiber.

  15. Comparison of γ-aminobutyric acid and biogenic amine content of different types of ewe’s milk cheese produced in Sardinia, Italy

    Directory of Open Access Journals (Sweden)

    Gavina Manca

    2015-06-01

    Full Text Available The bioactive compounds γ-aminobutyric acid (GABA and biogenic amines (BA, together with protein-free amino acids, were measured by high-performance liquid chromatography in ewe’s milk cheeses produced in Sardinia with different technological traits. The study included three types of cheese: Pecorino Sardo PDO, Pecorino and Casu Marzu. Farmhouse Casu Marzu and Pecorino showed GABA content (maximum levels: 1001.3 and 378.1 mg 100 g–1 respectively that had never been found so high in cheese before, suggesting that these types of cheese present ideal conditions to produce GABA. These two types of cheese also showed high levels of BA (their total maximum levels were 1035.7 and 288.0 mg 100 g–1 respectively. Pearson correlation analysis detected significant correlation between GABA and the main BA present in the cheeses (tyramine, cadaverine and putrescine, suggesting that the factors affecting the production of GABA are the same as those influencing BA formation.

  16. Synthesis of lithium silicates generators of tritium by a modified method of combustion

    International Nuclear Information System (INIS)

    Cruz G, D.

    2003-01-01

    analysis (TGA). It was found that the molar ratios more adequate of LiOH : H 2 SiO 3 : CH 4 N 2 O to produce Li 2 SiO 3 were: 3:1:3 and 3:1:6. The present carbonates in the powders prepared were eliminated in the second series by heating of the mixture to higher temperatures (650 C), or for washed of the same distilled water. The urea in excess produced coesite (SiO 2 ) as main product in the ceramics. Presently work was obtained, in accordance with the results, a sample of lithium silicate (Li 2 SiO 3 ) not polluted with any type of compound that it contained coal. (Author)

  17. Characterization of Physico-Chemical Properties and Antioxidant Capacities of Bioactive Honey Produced from Australian Grown Agastache rugosa and its Correlation with Colour and Poly-Phenol Content

    Directory of Open Access Journals (Sweden)

    Sushil Anand

    2018-01-01

    Full Text Available The antioxidant and antimicrobial components of honey vary based on sourced of nectar. Medicinal plants with the therapeutic value have potential to produce honey with greater bioactivity. The aim of the present study was to characterize the physico-chemical and antioxidant capacities of Agastache honey produced from Agastache rugosa and compare them with other popular commercial honeys sold in Australia. The total phenolics, total flavonoids, moisture content, colour, pH, protein content and antioxidant capacity were evaluated for Agastache, Manuka, Jelly bush, Tea tree, Super manuka and Jarrah honeys. The results reveal that the moisture content ranged from 17–21%, pH ranged from 3.8–4.3 and estimated protein content ranged from 900–2200 µg/g. The DPPH•, ABTS•+, ORAC and FRAP methods were used to measure the antioxidant capacity of the honey samples. The DPPH• % inhibition, ABTS•+, ORAC and FRAP values for Agastache honey were 9.85 (±1.98 µmol TE/g, 26.88 (±0.32 µmol TE/g, 19.78 (±1.1 µmol TE/g and 3.61 (±0.02 µmol TE/g whereas the highest antioxidant capacity values obtained were 18.69 (±0.9 µmol TE/g, 30.72 (±0.27 µmol TE/g, 26.95 (±0.9 µmol TE/g and 3.68 (±0.04 µmol TE/g, respectively. There was a positive correlation between colour, total phenolic content and DPPH• scavenging activity for most of the honeys except Tea tree honey. However, there was no clear correlation with ABTS•+, ORAC and FRAP values. The measured antioxidant capacity of samples varied with the assays used. The DPPH• assay clearly indicated that the phenolic compounds contribute to the scavenging activity of the honeys. Nevertheless, all assays confirm that Agastache honey has significant antioxidant capacity. Therefore, Agastache honey can be important to human nutrition and health.

  18. Quantification of trace level of fluoride content in uranium oxide produced by deconversion of HEX gas by ion chromatography

    International Nuclear Information System (INIS)

    Unnikrishnan, E.K.; Padmakumar, P.R.; Shanmugavelu, P.; Sudhakar, T.M.; Bhowmik, A.

    2015-01-01

    Fluoride content in nuclear fuel is detrimental due to its corrosion behavior with cladding material. It is essential to monitor and control the fluoride concentration in nuclear material at various processing stages. Deconversion of upgraded HEX gas is carried out to produce uranium oxide. The performance of the deconversion process of HEX gas is evaluated for which trace level of fluoride concentration accompanying uranium oxide is considered as a marker. An analytical method has been developed for testing the uranium oxide produced from deconversion process of HEX gas. The method involves sample pretreatment followed by analysis using ion chromatography. The test method was validated for its performance using in house synthetic uranyl fluoride (UO 2 F 2 ) standard solutions prepared with different level of fluoride content. The results are in agreement with the expected values with the recovery in the range of 80-95%. This method has been successfully implemented for routine analysis of samples at our lab. Since UO 2 F 2 reference material is not available to validate this method, in house UO 2 F 2 standards were prepared from U 3 O 8 prepared from nuclear grade uranyl nitrate solution. UO 2 F 2 standards were prepared by converting U 3 O 8 to UO 2 F 2 by the addition of HF followed by H 2 O 2 at 200°C on a hot plate. The entire yellow colored UO 2 F 2 was dissolved in nano pure water and recrystallised several times to ensure that all free HF is removed. The crystals dried in air oven at 120° for three hours. Samples containing 1000 mg kg -1 fluoride prepared from this UO 2 F 2 , and subsequently from this sample containing 5 mg kg -1 to 35 mg kg -1 fluoride samples were prepared and analysed against fluoride CRM and the fluoride concentration obtained was analysed

  19. Producing ashless coal extracts by microwave irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ozgur Sonmez; Elife Sultan Giray [Mersin University, Mersin (Turkey). Department of Chemistry

    2011-06-15

    To produce ashless coal extracts, three Turkish coals were extracted with N-methyl-2-pyrrolidinone (NMP), NMP/ethylenediamine (EDA) (17/1, vol/vol) mixture and NMP/tetralin (9/1, vol/vol) mixture through thermal extraction and microwave extraction. Solvent extraction by microwave irradiation (MI) was found to be more effective than that by thermal extraction. Extraction yield of coals in NMP enhanced by addition of a little EDA, but tetralin addition showed variances according to extraction method used. While tetralin addition caused a decrease in the thermal extraction yield, it increased the yield of the extraction by MI. Following the extraction, the solid extracts were produced with ash content ranging from 0.11% to 1.1%. Ash content of solid extract obtained from microwave extraction are less than ash contents of solid extracts obtained from thermal extraction. 34 refs., 7 figs., 5 tabs.

  20. 7 CFR 1124.62 - Announcement of producer prices.

    Science.gov (United States)

    2010-01-01

    ... butterfat, protein, nonfat solids, and other solids content of producer milk; and (g) The statistical... publicly the following prices and information: (a) The producer price differential; (b) The protein price....62 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING...

  1. Wild blueberry polyphenol-protein food ingredients produced by three drying methods: Comparative physico-chemical properties, phytochemical content, and stability during storage.

    Science.gov (United States)

    Correia, Roberta; Grace, Mary H; Esposito, Debora; Lila, Mary Ann

    2017-11-15

    Particulate colloidal aggregate food ingredients were prepared by complexing wheat flour, chickpea flour, coconut flour and soy protein isolate with aqueous wild blueberry pomace extracts, then spray drying, freeze drying, or vacuum oven drying to prepare dry, flour-like matrices. Physico-chemical attributes, phytochemical content and stability during storage were compared. Eighteen anthocyanins peaks were identified for samples. Spray dried matrices produced with soy protein isolate had the highest concentration of polyphenols (156.2mg GAE/g) and anthocyanins (13.4mg/g) and the most potent DPPH scavenging activity (714.1μmolesTE/g). Spray dried blueberry polyphenols complexed with protein were protected from degradation during 16weeks at 4°C and 20°C. Soy protein isolate more efficiently captured and stabilized wild blueberry pomace phytochemicals than other protein sources. Overall, spray drying the blueberry extracts complexed with protein proved to be an environment-friendly strategy to produce stable functional ingredients with multiple applications for the food industry. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Bioavailability of isoflavones from soy products in equol producers and non-producers in Japanese women

    OpenAIRE

    Ayako Miura; Chitose Sugiyama; Hiroyuki Sakakibara; Kayoko Simoi; Toshinao Goda

    2016-01-01

    Background: The estimated intake of soy isoflavones from a meal has been based on the content in a food, but the health effects of soy isoflavones are possibly affected by their bioavailability. In this study we have evaluated the isoflavone bioavailability after the intake of three kinds of soy foods and a commercial soy isoflavone supplement, and examined whether the isoflavone bioavailability is different between equol producers and non-producers. Methods: Healthy female subjects (n = 2...

  3. A Survey on Lead and Cadmium Content in Bread Produced in Yazd

    Directory of Open Access Journals (Sweden)

    B Hajimohammadi

    2015-11-01

    Full Text Available Introduction: Due to such complications of absorbing lead and cadmium heavy metals as kidney and liver dysfunction, vascular and heart diseases, anemia, digestive complications, nervous and skeletal problems and due to importance of bread as one of the most important food diets in Iran, especially in Yazd, the amount of lead and cadmium was evaluated in a variety of breads in Yazd. Methods: This descriptive cross-sectional study was carried out in 2013. Out of 69 bakeries, random probability proportionate sampling was applied in order to measure the heavy metals (lead and cadmium content in samples by ash and atomic absorption equipped with grafiti furnace(ETAAS with correction of background time. The study data were analyzed using SPSS (v.17 considering p-value of less than 0.05 as significant. Results: The average amounts of lead and cadmium were 99.05 and 7.49 mg/kg respectively. The amount of lead in Sangak bread was higher than that of other types of breads, whereas lead amounts of fantasy bread was reported less than those of other breads. Cadmium content demonstrated no significant differences among breads. Lead amount was higher in direct heat breads. Whereas, cadmium amount showed no significant differences between direct and indirect heat breads. It is worth mentioning that lead and cadmium content were reported lower than allowable levels in all samples. Conclusions: As the study results revealed and considering per capita consumption of bread in Iran (about 160 kg, it seems that weekly intake of lead and cadmium in Yazd is at an acceptable level, though possible risk of heavy metals(lead and cadmium need to decrease in order to prevent the probable risks of lead and cadmium heavy metals.

  4. How to Make Mathematical eContent Travel Well

    OpenAIRE

    Caprotti, Olga; Pauna, Matti; Seppälä, Mika

    2009-01-01

    Electronic content produced for education travels well when it can be reused across national borders and in different curricular frameworks. In this article, we discuss what features of mathematical e-content contribute to making it travel well.

  5. Method of producing ethyl alcohol

    Energy Technology Data Exchange (ETDEWEB)

    Philliskirk, G; Yates, H J

    1978-09-13

    Ethanol was produced from whey by removing protein from the whey by ultrafiltration, concentrating the deproteinized whey by reverse osmosis to a lactose content of at least 8 g/100 mL, fermenting with Candida pseudotropicalis NCYC 744, and distilling. E.g., milk whey was deproteinized to give a permeate containing 8.3 g lactose/100 mL. After fermentation, the final lactose content was 0.1 g/100 mL and the ethanol concentration was 3.55 g/100 mL, representing a 42% conversion of lactose to ethanol.

  6. Environmental and genetic factors influence the vitamin D content of cows' milk.

    Science.gov (United States)

    Weir, R R; Strain, J J; Johnston, M; Lowis, C; Fearon, A M; Stewart, S; Pourshahidi, L K

    2017-02-01

    Vitamin D is obtained by cattle from the diet and from skin production via UVB exposure from sunlight. The vitamin D status of the cow impacts the vitamin D content of the milk produced, much like human breast milk, with seasonal variation in the vitamin D content of milk well documented. Factors such as changes in husbandry practices therefore have the potential to impact the vitamin D content of milk. For example, a shift to year-round housing from traditional practices of cattle being out to graze during the summer months and housed during the winter only, minimises exposure to the sun and has been shown to negatively influence the vitamin D content of the milk produced. Other practices such as changing dietary sources of vitamin D may also influence the vitamin D content of milk, and evidence exists to suggest genetic factors such as breed can cause variation in the concentrations of vitamin D in the milk produced. The present review aims to provide an overview of the current understanding of how genetic and environmental factors influence the vitamin D content of the milk produced by dairy cattle. A number of environmental and genetic factors have previously been identified as having influence on the nutritional content of the milk produced. The present review highlights a need for further research to fully elucidate how farmers could manipulate the factors identified to their advantage with respect to increasing the vitamin D content of milk and standardising it across the year.

  7. GENERALIZATION, FORMULATION AND HEAT CONTENTS OF SIMULATED MSW WITH HIGH MOISTURE CONTENT

    Directory of Open Access Journals (Sweden)

    A. JOHARI

    2012-12-01

    Full Text Available This paper presents a generalization technique for the formulation of simulated municipal solid waste. This technique is used for the elimination of the inconsistency in the municipal solid waste (MSW characteristics due to its heterogeneous nature. The compositions of simulated municipal solid waste were formulated from four major municipal waste streams components in Malaysia namely paper, plastic, food and yard waste. The technique produced four simplified waste generalization categories with composition of paper (19%, plastic (25%, food (27% and green waste (29% respectively. Comparative study was conducted for proximate analysis for the determination of volatile matter, fixed carbon and ash content. Ultimate analysis was performed for carbon and hydrogen content. The heat content for simulated and actual municipal solid waste showed good agreement. The moisture content of the simulated municipal solid waste and actual municipal solid waste were established at 52.34% and 61.71% respectively. Overall results were considered to be representative of the actual compositions of municipal solid waste in Malaysia.

  8. Fly ash from a Mexican mineral coal. II. Source of W zeolite and its effectiveness in arsenic (V) adsorption

    International Nuclear Information System (INIS)

    Medina, Adriana; Gamero, Procoro; Almanza, Jose Manuel; Vargas, Alfredo; Montoya, Ascencion; Vargas, Gregorio; Izquierdo, Maria

    2010-01-01

    Coal-fired plants in Coahuila (Mexico) produce highly reactive fly ash (MFA), which is used in a one-step process as a raw material in producing zeolite. We explored two routes in the synthesis of zeolite: (a) direct MFA zeolitization, which resulted in the formation of W zeolite with KOH and analcime with NaOH and (b) a MFA fusion route, which resulted in the formation of zeolite W or chabazite with KOH and zeolite X or P with NaOH. No residual crystalline phases were present. When LiOH was employed, ABW zeolite with quartz and mullite were obtained. For both zeolitization routes, the nature of the alkali (KOH, NaOH, LiOH), the alkali/MFA ratio (0.23-1.46), and the crystallization temperature and time (90-175 o C; 8-24 h) were evaluated. Additionally, the effect of temperature and time on MFA fusion was studied. W zeolite was obtained by both zeolitization methods. The direct route is preferred because it is a straightforward method using soft reaction conditions that results in a high yield of low cost zeolites with large crystal agglomerates. It was demonstrated that aluminum modified W zeolite has the ability to remove 99% of the arsenic (V) from an aqueous solution of Na 2 HAsO 4 .7H 2 O originally containing 740 ppb.

  9. Fly ash from a Mexican mineral coal. II. Source of W zeolite and its effectiveness in arsenic (V) adsorption

    Energy Technology Data Exchange (ETDEWEB)

    Medina, Adriana [CINVESTAV IPN-Unidad Saltillo, Carretera Saltillo-Monterrey Km 13.5, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Gamero, Procoro, E-mail: pgamerom@hotmail.com [CINVESTAV IPN-Unidad Saltillo, Carretera Saltillo-Monterrey Km 13.5, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Almanza, Jose Manuel [CINVESTAV IPN-Unidad Saltillo, Carretera Saltillo-Monterrey Km 13.5, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Vargas, Alfredo; Montoya, Ascencion [Instituto Mexicano del Petroleo, Eje Central Lazaro Cardenas 152, G.A. Madero, C.P. 07730, Distrito Federal (Mexico); Vargas, Gregorio [CINVESTAV IPN-Unidad Saltillo, Carretera Saltillo-Monterrey Km 13.5, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Izquierdo, Maria [Instituto de Ciencias de la Tierra ' Jaume Almera' , CSIC, C/Luis Sole Sabaris, s/n 08028 Barcelona (Spain)

    2010-09-15

    Coal-fired plants in Coahuila (Mexico) produce highly reactive fly ash (MFA), which is used in a one-step process as a raw material in producing zeolite. We explored two routes in the synthesis of zeolite: (a) direct MFA zeolitization, which resulted in the formation of W zeolite with KOH and analcime with NaOH and (b) a MFA fusion route, which resulted in the formation of zeolite W or chabazite with KOH and zeolite X or P with NaOH. No residual crystalline phases were present. When LiOH was employed, ABW zeolite with quartz and mullite were obtained. For both zeolitization routes, the nature of the alkali (KOH, NaOH, LiOH), the alkali/MFA ratio (0.23-1.46), and the crystallization temperature and time (90-175 {sup o}C; 8-24 h) were evaluated. Additionally, the effect of temperature and time on MFA fusion was studied. W zeolite was obtained by both zeolitization methods. The direct route is preferred because it is a straightforward method using soft reaction conditions that results in a high yield of low cost zeolites with large crystal agglomerates. It was demonstrated that aluminum modified W zeolite has the ability to remove 99% of the arsenic (V) from an aqueous solution of Na{sub 2}HAsO{sub 4}.7H{sub 2}O originally containing 740 ppb.

  10. In-situ electrochemical study of Zr1nb alloy corrosion in high temperature Li{sup +} containing water

    Energy Technology Data Exchange (ETDEWEB)

    Krausová, Aneta [University of Chemistry and Technology, Technická 3, 166 28 Prague 6 (Czech Republic); Macák, Jan, E-mail: macakj@vscht.cz [University of Chemistry and Technology, Technická 3, 166 28 Prague 6 (Czech Republic); Sajdl, Petr [University of Chemistry and Technology, Technická 3, 166 28 Prague 6 (Czech Republic); Novotný, Radek [JRC-IET, Westerduinveg 3, 1755 LE Petten (Netherlands); Renčiuková, Veronika [University of Chemistry and Technology, Technická 3, 166 28 Prague 6 (Czech Republic); Vrtílková, Věra [ÚJP a.s., Nad Kamínkou 1345, 156 10 Prague 5 (Czech Republic)

    2015-12-15

    Long-term in-situ corrosion tests were performed in order to evaluate the influence of lithium ions on the corrosion of zirconium alloy. Experiments were carried out in a high-pressure high-temperature loop (280 °C, 8 MPa) in a high concentration water solution of LiOH (70 and 200 ppm Li{sup +}) and in a simulated WWER primary coolant environment. The kinetic parameters characterising the oxidation process have been explored using in-situ electrochemical impedance spectroscopy and slow potentiodynamic polarization. Also, a suitable equivalent circuit was suggested, which would approximate the impedance characteristics of the corrosion of Zr–1Nb alloy. The Mott–Schottky approach was used to determine the semiconducting character of the passive film. - Highlights: • Zr1Nb alloy was tested in WWER coolant and in LiOH solutions at 280 °C. • Corrosion rates were estimated in-situ from electrochemical data. • Electrochemical data agreed well with weight gains and metallography data. • Increase of corrosion rate in LiOH appeared after short exposure (300–500 h). • Very high donor densities (1.1–1.2 × 10{sup 20} cm{sup −3}) of Zr oxide grown in LiOH were found.

  11. Interaction of steel elements with products of lithium-water reactions

    International Nuclear Information System (INIS)

    Starkov, O.V.; Orlov, A.V.; Orlova, E.A.

    1980-01-01

    Isobar and isothermal potentials of reactions of products of lithium interaction with water (Li 2 O, LiOH) with components of structural steels (Fe, Cr, Ni, Cr 4 C, Ni, Ti, Si, Al) are calculated at the general pressure of P=1 at in the absence of mutual solubility of components. The chemical resistance of steel components to lithium oxide and hydroxide effect in the temperature range of 300-1500 K is estimated comparatively. Lithium oxide and hydroxide have different corrosion properties relatively to chromium-nickel steels (simple and complex compounds form with LiOH, which do not form with Li 2 O). Titanium, niobium, silicon, aluminium form stable compounds when interacting with LiOH. In reactions with Li 2 O only complex titanium compounds are stable at the temperature >1150 K; aluminium compounds are stable in the whole range of temperatures investigated

  12. Synthesis of lithium silicates generators of tritium by a modified method of combustion; Sintesis de silicatos de litio generadores de tritio por un metodo modificado de combustion

    Energy Technology Data Exchange (ETDEWEB)

    Cruz G, D

    2003-07-01

    -ray diffraction (XRD), Infrared spectroscopy (I S), semiquantitative elemental analysis (EDS) and Thermal gravimetric analysis (TGA). It was found that the molar ratios more adequate of LiOH : H{sub 2}SiO{sub 3} : CH{sub 4}N{sub 2}O to produce Li{sub 2}SiO{sub 3} were: 3:1:3 and 3:1:6. The present carbonates in the powders prepared were eliminated in the second series by heating of the mixture to higher temperatures (650 C), or for washed of the same distilled water. The urea in excess produced coesite (SiO{sub 2}) as main product in the ceramics. Presently work was obtained, in accordance with the results, a sample of lithium silicate (Li{sub 2}SiO{sub 3}) not polluted with any type of compound that it contained coal. (Author)

  13. 7 CFR 1001.62 - Announcement of producer prices.

    Science.gov (United States)

    2010-01-01

    ... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat solids price; (d) The other solids price; (e) The butterfat price; (f) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (g) The statistical uniform price for milk...

  14. Comparison of Journalistic Values of Television Reporters and Producers.

    Science.gov (United States)

    Smith, Conrad; Becker, Lee B.

    1989-01-01

    Analyzes the contention that television producers are representative of the show business side of news production whereas the reporter is the protector of the more noble journalistic goals. Finds little evidence that reporters are fighting producers to protect journalistic integrity. (RS)

  15. Aggregation, content farms and huffinization: the rise of low-pay and no-pay journalism

    NARCIS (Netherlands)

    Bakker, P.

    2012-01-01

    The business model of gathering, producing and distributing news is changing rapidly. Producing content is not enough; moderation and curation by "news workers" is at least as important. There is a growing pressure on news organizations to produce more inexpensive content for digital platforms,

  16. Content of Wax during Dewaxing Process: Adopting a DOE Method

    Directory of Open Access Journals (Sweden)

    Mohammad Hosein Eghbali

    2013-01-01

    Full Text Available The oil content of the wax produced in a dewaxing process is the key economic parameter that should be reduced as much as possible. Some factors such as the type of solvents, cooling rate, temperature, and solvent to oil ratio influence the dewaxing process. Due to the fact that crude oil differs from place to place and since the operational conditions for wax extraction vary for different types of crude oil, the objective of this work is to study the operational conditions for wax production from an Iranian raffinate sample used in Sepahan Oil Company. All the experiments are conducted based on a design of experiment (DOE technique for minimizing the oil content of the wax produced. The effects of five factors have been determined quantitatively and appropriate levels are suggested for reducing the oil content. The results show that the solvent ratio, solvent composition, and cooling rate play the most important role in minimizing the oil content of the produced wax.

  17. Comparison of consecutive harvests versus blending treatments to produce lower alcohol wines from Cabernet Sauvignon grapes: Impact on polysaccharide and tannin content and composition.

    Science.gov (United States)

    Schelezki, Olaf J; Smith, Paul A; Hranilovic, Ana; Bindon, Keren A; Jeffery, David W

    2018-04-01

    A changing climate has led to winegrapes being harvested with increased sugar levels and at greater risk of berry shrivel. A suggested easy-to-adopt strategy to manage the associated rising wine alcohol levels is the pre-fermentative substitution of juice with either "green harvest wine" or water. Our study investigates the effects of this approach on Vitis vinifera L. cv. Cabernet Sauvignon wine quality attributes. Wines were also made from fruit collected at consecutive earlier harvest time points to produce wines comparable in alcohol to the substituted wines. Tannin concentrations and colour did not change significantly in the wines with modified alcohol content even at higher juice substitution rates. Differences in polysaccharide and tannin composition indicated variability in extraction dynamics according to substitution rate and type of blending component. In scenarios where berry shrivel is inevitable, the incorporation of water in particular offers much promise as part of a strategy to manage wine alcohol content. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Mechanical properties of lightweight aerated concrete with different aluminium powder content

    Directory of Open Access Journals (Sweden)

    Shabbar Rana

    2017-01-01

    Full Text Available Aerated concrete is produced by introducing gas into a concrete, the amount dependent upon the requirements for strength. One method to achieve this is by using powdered aluminium which reacts with the calcium hydroxide produced upon hydration of the cement. The aim of the current study was to investigate the influence of the powder content on the mechanical properties of aerated concrete namely; compressive and flexural strengths, modulus of elasticity, density and porosity. The results indicated that an increase in aluminium content caused a decrease in the compressive and tensile strengths. It also produced a decrease in the modulus of elasticity. When the aluminium content increased, the density decreased and the porosity increased.

  19. Physical properties of honeys produced in the Northeast of Brazil

    Directory of Open Access Journals (Sweden)

    Patricia Argemira Costa

    2013-04-01

    Full Text Available The aim of this work was to study the rheological, thermal and some other physical-chemical properties of selected honeys produced in the Northeast of Brazil. Two samples were produced by native “Jandaira” bees (Melipona subnitida and ten other samples by Africanized bees (Apis mellifera. The samples were analyzed for pH, water activity (aW, soluble solids and water content. Viscosity flow curves were obtained using a rheometer (25ºC, 0-100s-1. Thermal analyses were performed on a differential scanning calorimeter, with heating rate of 10ºC/min (-100 to 100ºC. The water content and the pH of the honey samples varied from 17.2 to 27.9% and from 3.2 to 4.2, respectively, and, the aW of the samples varied from 0.57 to 0.74. Two samples were out of specification with respect to water content, according to Brazilian laws. In relation to rheology, all honey samples showed Newtonian behaviour with no thixotropy or dilatancy. The viscosity varied as an exponential function of the water content. The highest viscosity was obtained for the sample with lower values of water content and aW. Thermograms showed a glass transition (Tg occurring between -52.4 and -42.6ºC, in the samples produced by Apis mellifera and -67.6 and -57.0ºC for the other samples. A linear relationship was obtained between Tg and water content. In conclusion, the honey viscosity depended on the water content of the product. The higher the water value and therefore the greater the aw, the lower viscosity and Tg of the samples.

  20. Corrosion characteristics and oxide microstructures of Zircaloy-4 in aqueous alkali hydroxide solutions

    International Nuclear Information System (INIS)

    Jeong, Y.H.; Baek, J.H.; Kim, S.J.; Kim, H.G.

    1999-01-01

    The corrosion characteristics of Zircaloy-4 have been investigated in various aqueous solutions of LiOH, NaOH, KOH, RbOH and CsOH with equimolar M + and OH - at 350 C. The characterization of the oxides was performed using transmission electron microscope (TEM) and scanning electron microscope (SEM) on the samples which were prepared to have an equal oxide thickness in pre-transition and post-transition regimes. At a low concentration (4.3 mmol) of aqueous alkali hydroxide solutions, the corrosion rates decrease gradually as the ionic radius of cation increases. At a high concentration (32.5 mmol), the corrosion rate increases significantly in LiOH solution and slightly in NaOH solution, but in the other hydroxide solutions such as KOH, RbOH and CsOH, the corrosion rate is not accelerated. Even if the specimens have an equal oxide thickness in LiOH, NaOH and KOH solutions, the oxide microstructure formed in the LiOH solution is quite different from those formed in the NaOH or the KOH solutions. In the LiOH solution, the oxides grown in the pre-transition regime as well as in the post-transition regime have an equiaxed structure including many pores and open grain boundaries. The oxides grown in the NaOH solution have a protective columnar structure in the pre-transition regime but an equiaxed structure in the post-transition regime. On the other hand, in the KOH solution, the columnar structure is maintained from its pre-transition regime to the post-transition regime. On the basis of the above results, it can be suggested that the cation incorporation into zirconium oxide would control the oxide microstructure, the oxide growth mechanism at the metal-oxide interface and the corrosion rate in alkali hydroxide solutions. (orig.)

  1. Effect of Acetylene Black Content in Li4Ti5O12 Xerogel Solid-State Anode Materials on Half-Cell Li-ion Batteries Performance

    Science.gov (United States)

    Abdurrahman, N. M.; Priyono, B.; Syahrial, A. Z.; Subhan, A.

    2017-07-01

    The effect of Acetylene Black (AB) additive contents in lithium titanate/Li4Ti5O12 (LTO) anode on Li-ion Batteries performance is studied in this work. The LTO active material for Li-ion batteries anode was successfully synthesized using sol-gel method to form TiO2 xerogel continued by mixing process with LiOH in ball-mill and then sintered to obtain spinel LTO. The LTO powder is characterized by X-Ray Diffraction (XRD), scanning electron microscopy-Energy Dispersive Spectroscopy (SEM-EDS), and Brunauer-Emmett-Teller (BET). The spinel LTO and TiO2 rutile were detected by XRD diffractogram. The LTO powder is in the form of agglomerates structure. This powder then was mixed with PVDF binder (10%wt) and AB additives with various amount from 10%wt (LTO2 Ac-1), 12%wt (LTO2 Ac-2), and 15%wt (LTO2 Ac-3) of total weight solid content to form electrode sheet. Half-cell coin battery was made with lithium metal foil as a counter electrode. Cyclic voltammetry (CV), Electrochemical-impedance spectroscopy (EIS), and charge discharge (CD) test used to examine the battery performance. The highest resistance value is obtained in LTO2 Ac-3 sample with 15%wt of AB. It might be caused by the formation of side reaction product on electrode surface at initial cycle due to high reactivity of LTO2 Ac-3 electrode. The highest initial capacity at CV test and CD test was obtained in LTO2 Ac-1 (10%wt AB) sample, due to the best proportion of active material content in the compound. While, in the charge-discharge test at high current rate, the best sample rate-capability performance belongs to LTO2 Ac-3 sample (15%wt AB), which still have 24.12 mAh/g of discharge capacity at 10 C with 71.34% capacity loss.

  2. Characterization of Soluble Organics in Produced Water

    Energy Technology Data Exchange (ETDEWEB)

    Bostick, D.T.

    2002-01-16

    Soluble organics in produced water and refinery effluents represent treatment problems for the petroleum industry. Neither the chemistry involved in the production of soluble organics nor the impact of these chemicals on total effluent toxicity is well understood. The U.S. Department of Energy provides funding for Oak Ridge National Laboratory (ORNL) to support a collaborative project with Shell, Chevron, Phillips, and Statoil entitled ''Petroleum and Environmental Research Forum project (PERF 9844: Manage Water-Soluble Organics in Produced Water''). The goal of this project, which involves characterization and evaluation of these water-soluble compounds, is aimed at reducing the future production of such contaminants. To determine the effect that various drilling conditions might have on water-soluble organics (WSO) content in produced water, a simulated brine water containing the principal inorganic components normally found in Gulf of Mexico (GOM) brine sources was prepared. The GOM simulant was then contacted with as-received crude oil from a deep well site to study the effects of water cut, produced-water pH, salinity, pressure, temperature, and crude oil sources on the type and content of the WSO in produced water. The identities of individual semivolatile organic compounds (SVOCs) were determined in all as-received crude and actual produced water samples using standard USEPA Method (8270C) protocol. These analyses were supplemented with the more general measurements of total petroleum hydrocarbon (TPH) content in the gas (C{sub 6}-C{sub 10}), diesel (C{sub 10}-C{sub 20}), and oil (C{sub 20}-C{sub 28}) carbon ranges as determined by both gas chromatographic (GC) and infrared (IR) analyses. An open liquid chromatographic procedure was also used to differentiate the saturated hydrocarbon, aromatic hydrocarbon, and polar components within the extractable TPH. Inorganic constituents in the produced water were analyzed by ion

  3. Measurement of broiler litter production rates and nutrient content using recycled litter.

    Science.gov (United States)

    Coufal, C D; Chavez, C; Niemeyer, P R; Carey, J B

    2006-03-01

    It is important for broiler producers to know litter production rates and litter nutrient content when developing nutrient management plans. Estimation of broiler litter production varies widely in the literature due to factors such as geographical region, type of housing, size of broiler produced, and number of flocks reared on the same litter. Published data for N, P, and K content are also highly variable. In addition, few data are available regarding the rate of production, characteristics, and nutrient content of caked litter (cake). In this study, 18 consecutive flocks of broilers were reared on the same litter in experimental pens under simulated commercial conditions. The mass of litter and cake produced was measured after each flock. Samples of all litter materials were analyzed for pH, moisture, N, P, and K. Average litter and cake moisture content were 26.4 and 46.9%, respectively. Significant variation in litter and cake nutrient content was observed and can largely be attributed to ambient temperature differences. Average litter, cake, and total litter (litter plus cake) production rates were 153.3, 74.8, and 228.2 g of dry litter material per kg of live broiler weight (g/kg) per flock, respectively. Significant variation in litter production rates among flocks was also observed. Cumulative litter, cake, and total litter production rates after 18 flocks were 170.3, 78.7, and 249.0 g/kg, respectively. The data produced from this research can be used by broiler producers to estimate broiler litter and cake production and the nutrient content of these materials.

  4. Enhancement of the folate content in Egyptian pita bread.

    Science.gov (United States)

    Hefni, Mohammed; Witthöft, Cornelia M

    2012-01-01

    Egypt has a high incidence of neural tube defects related to folate deficiency. One major food source for folate is pita (baladi) bread, which is consumed daily. Bioprocessing (e.g. germination) has been reported to increase the folate content in cereals. The aim was to produce pita bread with increased folate content using germinated wheat flour (GWF). Prior to milling the effects of germination and drying conditions on folate content in wheat grains were studied. Pita bread was baked from wheat flour substituted with different levels of GWF. The folate content in dough and bread and rheological properties of dough were determined. Germination of wheat grains resulted in, depending on temperature, 3- to 4-fold higher folate content with a maximum of 61 µg/100 g DM (dry matter). The folate content in both flour and bread increased 1.5 to 4-fold depending on the level of flour replacement with GWF. Pita bread baked with 50% sieved GWF was acceptable with respect to colour and layer separation, and had a folate content of 50 µg/100 g DM compared with 30 µg/100 g DM in conventional pita bread (0% GWF). Using 50% GWF, pita bread with increased folate content, acceptable for the Egyptian consumer, was produced. Consumption of this bread would increase the average daily folate intake by 75 µg.

  5. Enhancement of the folate content in Egyptian pita bread

    Directory of Open Access Journals (Sweden)

    Cornelia M. Witthöft

    2012-04-01

    Full Text Available Introduction: Egypt has a high incidence of neural tube defects related to folate deficiency. One major food source for folate is pita (baladi bread, which is consumed daily. Bioprocessing (e.g. germination has been reported to increase the folate content in cereals. The aim was to produce pita bread with increased folate content using germinated wheat flour (GWF.Methods: Prior to milling the effects of germination and drying conditions on folate content in wheat grains were studied. Pita bread was baked from wheat flour substituted with different levels of GWF. The folate content in dough and bread and rheological properties of dough were determined.Results: Germination of wheat grains resulted in, depending on temperature, 3- to 4-fold higher folate content with a maximum of 61 µg/100 g DM (dry matter. The folate content in both flour and bread increased 1.5 to 4-fold depending on the level of flour replacement with GWF. Pita bread baked with 50% sieved GWF was acceptable with respect to colour and layer separation, and had a folate content of 50 µg/100 g DM compared with 30 µg/100 g DM in conventional pita bread (0% GWF.Conclusion: Using 50% GWF, pita bread with increased folate content, acceptable for the Egyptian consumer, was produced. Consumption of this bread would increase the average daily folate intake by 75 µg.

  6. Changes in Hydrogen Content During Steelmaking

    Directory of Open Access Journals (Sweden)

    Vrbek K.

    2015-04-01

    Full Text Available Štore Steel produces steel grades for spring, forging and engineering industry applications. Steelmaking technology consists of scrap melting in Electric Arc Furnace (EAF, secondary metallurgy in Ladle Furnace (LF and continuous casting of billets (CC. Hydrogen content during steelmaking of various steel grades and steelmaking technologies was measured. Samples of steel melt from EAF, LF and CC were collected and investigated. Sampling from Electric Arc Furnace and Ladle Furnace was carried out using vacuum pin tubes. Regular measurements of hydrogen content in steel melt were made using Hydris device. Hydrogen content results measured in tundish by Hydris device were compared with results from pin tube samples. Based on the measurement results it was established that hydrogen content during steelmaking increases. The highest values were determined in tundish during casting. Factors that influence the hydrogen content in liquid steel the most were steelmaking technology and alloying elements.

  7. Application of laser-produced-plasmas to determination of carbon content in steel; Aplicacion de los plasmas generados por laser a la determinacion de carbono en aceros

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz, M; Aragon, C; Aguilera, J A; Campos, J

    1994-07-01

    This paper describes an analytical method to determine carbon content in solid and molten steel. It is based on the study of the emission spectrum from a Nd-YAG laser produced plasma. The light emitted from the plasma is focused to the entrance slit of a spectrometer and detected by an OMA III system. For every laser pulse an spectral range of 100 A are recorded. With the use of time-resolved spectroscopy a precision of 1.6 % and a detection limit of 65 ppm of carbon content in steel have been obtained. These values are similar to those of other accurate conventional techniques but using optics fiber and laser excitation it is possible to made sample calibrations in hostile environments. Also, as the analysis are made in real time changes in sample composition can be measured without stopping production processes. (Author) 26 refs.

  8. In situ observation of lithium hydride hydrolysis by DRIFT spectroscopy

    International Nuclear Information System (INIS)

    Awbery, Roy P.; Broughton, Duncan A.; Tsang, S.C.

    2008-01-01

    Polycrystalline LiH was studied in situ using diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy to investigate the effect water vapour has on the rate of production of the corrosion products, particularly LiOH. The reaction rate of the formation of surface LiOH was monitored by measurement of the hydroxyl (OH) band at 3676 cm -1 . The initial hydrolysis rate of LiH exposed to water vapour at 50% relative humidity was found to be almost two times faster than LiH exposed to water vapour at 2% relative humidity. The hydrolysis rate was shown to be initially very rapid followed by a much slower, almost linear rate. The change in hydrolysis rate was attributed to the formation of a coherent layer of LiOH on the LiH surface. Exposure to lower levels of water vapour appeared to result in the formation of a more coherent corrosion product, resulting in effective passivation of the surface to further attack from water

  9. Controllable synthesis of ZnO nanoparticles with high intensity visible photoemission and investigation of its mechanism

    International Nuclear Information System (INIS)

    Lv Yunbo; Xiao Wen; Li Weiyan; Xue Junmin; Ding Jun

    2013-01-01

    ZnO is known as a good photoluminescent semiconductor due to its ability to emit visible light. However, the visible emission mechanism is still under debate. In this work, we have successfully synthesized nanoparticles using LiOH, KOH and NaOH as bases and have achieved visible emission of various colours, such as blue, cyan, green and orange. We demonstrate that LiOH is the most efficient base to control the properties of ZnO nanoparticle emission by varying LiOH concentration. Moreover, detailed studies by TEM, UV and XRD show that ZnO particle size plays an important role in the colour of the emitted light and smaller particles tend to emit shorter wavelength photons. The visible emission is suggested to arise from an electron transition from the conduction band to a deep-trapped defect state. Our experimental results suggest the presence of oxygen vacancies on the ZnO nanoparticle surface. (paper)

  10. Development of Pressure Swing Adsorption Technology for Spacesuit Carbon Dioxide and Humidity Removal

    Science.gov (United States)

    Papale, William; Paul, Heather; Thomas, Gretchen

    2006-01-01

    Metabolically produced carbon dioxide (CO2) removal in spacesuit applications has traditionally been accomplished utilizing non-regenerative Lithium Hydroxide (LiOH) canisters. In recent years, regenerative Metal Oxide (MetOx) has been developed to replace the Extravehicular Mobility Unity (EMU) LiOH canister for extravehicular activity (EVA) missions in micro-gravity, however, MetOx may carry a significant weight burden for potential use in future Lunar or planetary EVA exploration missions. Additionally, both of these methods of CO2 removal have a finite capacity sized for the particular mission profile. Metabolically produced water vapor removal in spacesuits has historically been accomplished by a condensing heat exchanger within the ventilation process loop of the suit life support system. Advancements in solid amine technology employed in a pressure swing adsorption system have led to the possibility of combining both the CO2 and humidity control requirements into a single, lightweight device. Because the pressure swing adsorption system is regenerated to space vacuum or by an inert purge stream, the duration of an EVA mission may be extended significantly over currently employed technologies, while markedly reducing the overall subsystem weight compared to the combined weight of the condensing heat exchanger and current regenerative CO2 removal technology. This paper will provide and overview of ongoing development efforts evaluating the subsystem size required to manage anticipated metabolic CO2 and water vapor generation rates in a spacesuit environment.

  11. Carbon fuel particles used in direct carbon conversion fuel cells

    Science.gov (United States)

    Cooper, John F.; Cherepy, Nerine

    2012-10-09

    A system for preparing particulate carbon fuel and using the particulate carbon fuel in a fuel cell. Carbon particles are finely divided. The finely dividing carbon particles are introduced into the fuel cell. A gas containing oxygen is introduced into the fuel cell. The finely divided carbon particles are exposed to carbonate salts, or to molten NaOH or KOH or LiOH or mixtures of NaOH or KOH or LiOH, or to mixed hydroxides, or to alkali and alkaline earth nitrates.

  12. Carbon Fuel Particles Used in Direct Carbon Conversion Fuel Cells

    Science.gov (United States)

    Cooper, John F.; Cherepy, Nerine

    2008-10-21

    A system for preparing particulate carbon fuel and using the particulate carbon fuel in a fuel cell. Carbon particles are finely divided. The finely dividing carbon particles are introduced into the fuel cell. A gas containing oxygen is introduced into the fuel cell. The finely divided carbon particles are exposed to carbonate salts, or to molten NaOH or KOH or LiOH or mixtures of NaOH or KOH or LiOH, or to mixed hydroxides, or to alkali and alkaline earth nitrates.

  13. Investigation of effective parameters in preparation and controlling lithium fluoride nano size powder

    International Nuclear Information System (INIS)

    Naderi, S.; Sarraf Mamoory, F.; Riahi Noori, N.

    2007-01-01

    In this research, the reaction of LiOH + HF+LiF+H 2 O has been selected and some precipitation parameters such as pH, temperature, time, super saturation, q d agitation type have been studied, and controlled. The morphology, phase analysis and particle size of the resulting powders were analyzed by SEM, XRD and LPSA. Finally, at temperature 2S d ig C , pH of about 2-3, reaction time less than 1 sec, and agitation by ultrasonic bath, the pure nano lithium fluoride powders of about 100 nm were produced

  14. Trace metal contents of selected seeds and vegetables from oil producing areas of Nigeria.

    Science.gov (United States)

    Wegwu, Matthew O; Omeodu, Stephen I

    2010-07-01

    The concentrations of accumulated trace metals in selected seeds and vegetables collected in the oil producing Rivers State of Nigeria were investigated. The values were compared with those of seeds and vegetables cultivated in Owerri, a less industrialized area in Nigeria. The lead (Pb) and cadmium (Cd) contents of the seeds obtained from Rivers State ranged between 0.10 and 0.23 microg/g dry weight, while those of the seeds cultivated in Owerri fell below the detection limit of 0.01 microg/g dry weight. The highest manganese (Mn) level (902 microg/g dry weight) was found in Irvingia garbonesis seeds cultivated in Rivers State. Similarly, the highest nickel (Ni) value (199 microg/g dry weight) was also obtained in I. garbonesis, however, in the seeds sampled in Owerri. The highest copper (Cu), zinc (Zn), and iron (Fe) levels (16.8, 5.27, and 26.2 microg/g dry weight, resp.) were detected in seeds collected in Rivers State. With the exception of Talinum triangulae, Ocinum gratissimum, and Piper guineese, with Pb levels of 0.09, 0.10, and 0.11 microg/g dry weight, respectively, the Pb and Cd levels in the vegetables grown in Owerri fell below the detection limit of 0.01 microg/g dry weight. The trace metal with the highest levels in all the vegetables studied was Mn, followed by Fe. The highest concentrations of Ni and Cu occurred in vegetables collected from Rivers State, while the highest level of Zn was observed in Piper guineese collected in Owerri, with a value of 21.4 microg/g dry weight. Although the trace metal concentrations of the seeds and vegetables collected in Rivers State tended to be higher than those of the seeds and vegetables grown in Owerri, the average levels of trace metals obtained in this study fell far below the WHO specifications for metals in foods.

  15. THE PROBLEM OF CREATION AND CONSUMING OF MEDIA CONTENT OF INNOVATIVE PR

    Directory of Open Access Journals (Sweden)

    Berezenko Vita Vitalyevna

    2013-04-01

    Full Text Available The article analyses on the theoretical level the media content of innovative public relations which can be conveyed via the possibilities of online communication; it also defines the characteristic features of the media content drawing attention of scientific community ( scholars. The purpose of this article - review of the production and consumption of media content of innovative PR in Ukraine at the theoretical level. Problems of creating and consuming of innovative PR media content are determined; among them the problem of professional training and state of being ready of all participants of communication for adequate perception and consuming of innovative media content, intellectual product, as soon as they are science consuming a priori, i.e. complex; the problem of copyright for intellectual product created by both producer and consumer, i.e. created by their mutual efforts. Public relations produce new characteristics of content in media while carrying out strategic functions in the Ukrainian society.

  16. Unsupervised Segmentation Methods of TV Contents

    Directory of Open Access Journals (Sweden)

    Elie El-Khoury

    2010-01-01

    Full Text Available We present a generic algorithm to address various temporal segmentation topics of audiovisual contents such as speaker diarization, shot, or program segmentation. Based on a GLR approach, involving the ΔBIC criterion, this algorithm requires the value of only a few parameters to produce segmentation results at a desired scale and on most typical low-level features used in the field of content-based indexing. Results obtained on various corpora are of the same quality level than the ones obtained by other dedicated and state-of-the-art methods.

  17. Determining gold content

    International Nuclear Information System (INIS)

    Clayton, C.G.; Wormald, M.R.

    1981-01-01

    A method for determining the gold content of a material, comprises irradiating a body of the material with neutrons and determining the intensity of γ-rays having an energy of 279 keV arising from the reaction 179 Au(nn') 179 Au → 279 keV. The apparatus has means for conveying the materials past an assembly, which has a neutron source, which does not produce neutrons having sufficient energy to excite fast neutron reactions in non-auriferous constituents. (author)

  18. Determination of Some Quality Criteria of the Kefir Produced with Molasses and Plum

    Directory of Open Access Journals (Sweden)

    Tuğba Kök Taş

    2014-02-01

    Full Text Available The aim of this study is to determine the quality characteristics of kefir by developing different flavours in order to increase its consumption. Plum (10% and molasses (7.5% which are rich in phenolic contents are used to produce kefir in different flavours. Chemical analysis (pH, titratable acidity, dry matter and colour, microbial analysis (total microorganism, Lactobacillus spp, Lactococcus spp. and yeast counts, total antioxidant activity (by ORAC method, total amount of phenolic contents and sensorial properties of all kefir samples were carried out at the 1st, 7th and 14th days of storage. Consequently, the results of pH, titratable acidity and dry matter in the kefir samples were determined to change between the values 4.11-4.39; 0.22-0.30 and 11.9-17.02% respectively, during the storage. In the colour analysis, the redness colour parameter of the kefir sample produced using molasses was determined to be higher compared to the other kefir samples. At the first day of storage, the total antioxidant contents of the control group kefir, plum- added kefir and molasses-added kefir samples were determined as 13.30; 16.80 and 17.35 µmol ml-1; and the total phenolic contents as 945.70; 2535.8 and 2357.6 mg ml-1, respectively. Content of total microorganism in kefir samples varied between 8.91-9.80 log kob ml-1during the storage period. Lactobacillus spp. and Lactococcus spp. contents of kefir produced using molasses were determined to have the highest values with 9.11 and 9.91 log kob ml-1, respectively, at the first day. Yeast content of the plum kefir and the molasses kefir samples including sugar was detected to be higher than that of the controlled kefir sample. According to the results of the sensory analysis, the kefir produced with plum was approved the most by the panelists. As a result of this study, two alternative products with quite high total phenolic content and antioxidant activity were developed for consumers.

  19. Evaluation of phenolic compounds content and in vitro antioxidant activity of red wines produced from Vitis labrusca grapes

    Directory of Open Access Journals (Sweden)

    Daniel Braga de Lima

    2011-09-01

    Full Text Available Wine production in the northern Curitiba, Paraná, Brazil, specifically the communes of Colombo and Almirante Tamandaré, is based mainly on the utilization of Vitis labrusca grapes var. Bordô (Ives. Total sugar content, pH, and total acidity were analyzed in red wine samples from 2007 and 2008 vintages following official methods of analysis. Moreover, total phenolic, flavonoid, and tannin contents were analyzed by colorimetric methodologies and the antioxidant activity was determined using the 2,2-diphenyl-1-picrylhydrazyl (DPPH radical methodology. Phenolic compounds were identified by high performance liquid chromatography. The total phenolic content of wine samples presented concentrations varying between 1582.35 and 2896.08 mg gallic acid.L-1 since the major part corresponds to flavonoid content. In these compounds' concentration range, a direct relationship between phenolic compounds content and levels of antioxidant activity was not observed. Among the identified phenolic compounds, chlorogenic, caffeic, and syringic acids were found to be the major components. Using three principal components, it was possible to explain 81.36% of total variance of the studied samples. Principal Components Analysis does not differentiate between vintages.

  20. Impurities in chromium deposits produced by electroplating and physical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Dini, J.W.

    1994-05-01

    Impurity contents in electrodeposited (hexavalent and trivalent) chromium deposits and physically vapor deposited (thermal evaporation, electron beam evaporation and rf-sputtering) were compared. Oxygen is the key impurity obtained in electrodeposited films but it can be minimized in hexavalent plating solutions by operating at high temperature, e. g., 85 C. Electrodeposits produced in trivalent chromium plating solutions and physically vapor deposited films have much higher oxygen contents than electrodeposits produced in hexavalent chromium solutions operated at temperatures around 85 C. Depending on the target material used for physically vapor deposited films, these films can also have high amounts of other impurities.

  1. Producing ergosterol from corn straw hydrolysates using ...

    African Journals Online (AJOL)

    Ergosterol is an economically important metabolite produced by Saccharomyces cerevisiae. In this study, the production of ergosterol by the strain using corn straw as an inexpensive carbon source was investigated. The total yield of ergosterol was determined by both the biomass and ergosterol content in yeast cells which ...

  2. 7 CFR 1126.62 - Announcement of producer prices.

    Science.gov (United States)

    2010-01-01

    ....62 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE SOUTHWEST MARKETING...; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h...

  3. 7 CFR 1030.62 - Announcement of producer prices.

    Science.gov (United States)

    2010-01-01

    ... cell adjustment rate; (g) The average butterfat, nonfat solids, protein and other solids content of... publicly the following prices and information: (a) The producer price differential; (b) The protein price....62 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING...

  4. An analysis of infiltration with moisture content distribution in a two-dimensional discretized water content domain

    KAUST Repository

    Yu, Han; Douglas, Craig C.

    2014-01-01

    On the basis of unsaturated Darcy's law, the Talbot-Ogden method provides a fast unconditional mass conservative algorithm to simulate groundwater infiltration in various unsaturated soil textures. Unlike advanced reservoir modelling methods that compute unsaturated flow in space, it only discretizes the moisture content domain into a suitable number of bins so that the vertical water movement is estimated piecewise in each bin. The dimensionality of the moisture content domain is extended from one dimensional to two dimensional in this study, which allows us to distinguish pore shapes within the same moisture content range. The vertical movement of water in the extended model imitates the infiltration phase in the Talbot-Ogden method. However, the difference in this extension is the directional redistribution, which represents the horizontal inter-bin flow and causes the water content distribution to have an effect on infiltration. Using this extension, we mathematically analyse the general relationship between infiltration and the moisture content distribution associated with wetting front depths in different bins. We show that a more negatively skewed moisture content distribution can produce a longer ponding time, whereas a higher overall flux cannot be guaranteed in this situation. It is proven on the basis of the water content probability distribution independent of soil textures. To illustrate this analysis, we also present numerical examples for both fine and coarse soil textures.

  5. An analysis of infiltration with moisture content distribution in a two-dimensional discretized water content domain

    KAUST Repository

    Yu, Han

    2014-06-11

    On the basis of unsaturated Darcy\\'s law, the Talbot-Ogden method provides a fast unconditional mass conservative algorithm to simulate groundwater infiltration in various unsaturated soil textures. Unlike advanced reservoir modelling methods that compute unsaturated flow in space, it only discretizes the moisture content domain into a suitable number of bins so that the vertical water movement is estimated piecewise in each bin. The dimensionality of the moisture content domain is extended from one dimensional to two dimensional in this study, which allows us to distinguish pore shapes within the same moisture content range. The vertical movement of water in the extended model imitates the infiltration phase in the Talbot-Ogden method. However, the difference in this extension is the directional redistribution, which represents the horizontal inter-bin flow and causes the water content distribution to have an effect on infiltration. Using this extension, we mathematically analyse the general relationship between infiltration and the moisture content distribution associated with wetting front depths in different bins. We show that a more negatively skewed moisture content distribution can produce a longer ponding time, whereas a higher overall flux cannot be guaranteed in this situation. It is proven on the basis of the water content probability distribution independent of soil textures. To illustrate this analysis, we also present numerical examples for both fine and coarse soil textures.

  6. Crowdsourcing Content Creation in the Classroom

    Science.gov (United States)

    Hills, Thomas T.

    2015-01-01

    The recent growth in crowdsourcing technologies offers a new way of envisioning student involvement in the classroom. This article describes a participatory action research approach to combining crowdsourced content creation with the student as producer model, whereby students' interests are used to drive the identification and creation of…

  7. Postharvest changes in glycoalkaloid content of potatoes.

    Science.gov (United States)

    Friedman, M; McDonald, G M

    1999-01-01

    Potatoes contain antinutritional and potentially toxic compounds including inhibitors of digestive enzymes, hemagglutinins, and glycoalkaloids. Solanum glycoalkaloids are reported to inhibit cholinesterase, disrupt cell membranes, and induce teratogenicity. In this overview, we describe the role of potatoes in the human diet, reported changes in glycoalkaloid content of fresh and processed potatoes during storage, under the influence of light and radiation, following mechanical damage, and as a result of food processing. Also covered are safety aspects and suggested research needs to develop a protocol that can be adopted by the potato producers and processors to minimize post-harvest synthesis of glycoalkaloids in potatoes. Reducing the glycoalkaloid content of potatoes will provide a variety of benefits extending from the farm to processing, shipping, marketing, and consumption of potatoes and potato products. A commercially available ELISA kit is described which permits rapid assay of glycoalkaloid content of parts of the potato plant including leaves, tubers, and peel, as well as processed potato products including french fries, chips, and skins. Understanding the multiple overlapping aspects of glycoalkaloids in the plant and in the diet will permit controlling postharvest glycoalkaloid production for the benefit of the producer and consumer.

  8. Summarizing Audiovisual Contents of a Video Program

    Science.gov (United States)

    Gong, Yihong

    2003-12-01

    In this paper, we focus on video programs that are intended to disseminate information and knowledge such as news, documentaries, seminars, etc, and present an audiovisual summarization system that summarizes the audio and visual contents of the given video separately, and then integrating the two summaries with a partial alignment. The audio summary is created by selecting spoken sentences that best present the main content of the audio speech while the visual summary is created by eliminating duplicates/redundancies and preserving visually rich contents in the image stream. The alignment operation aims to synchronize each spoken sentence in the audio summary with its corresponding speaker's face and to preserve the rich content in the visual summary. A Bipartite Graph-based audiovisual alignment algorithm is developed to efficiently find the best alignment solution that satisfies these alignment requirements. With the proposed system, we strive to produce a video summary that: (1) provides a natural visual and audio content overview, and (2) maximizes the coverage for both audio and visual contents of the original video without having to sacrifice either of them.

  9. TEACHER-PRODUCED INSTRUCTIONAL FILMS IN CHEMISTRY, 8MM AND SUPER 8.

    Science.gov (United States)

    O'CONNOR, ROD; SLABAUGH, WENDELL

    TECHNIQUES FOR PRODUCING 8MM INSTRUCTIONAL FILMS IN CHEMISTRY ARE PRESENTED. IN PART I A PHILOSOPHY OF TEACHER-PRODUCED FILMS IS DEVELOPED, EMPHASIZING THE VALUE OF THE LOCAL SETTING, AND CUSTOM-MADE CONTENTS. APPLICATIONS SUGGESTED ARE (1) TECHNIQUE INSTRUCTION, (2) FILMED EXPERIMENTS, (3) INSTRUMENT FAMILIARIZATION, (4) LECTURE AIDS, AND (5)…

  10. Portable rapid gas content measurement - an opportunity for a step change in the coal industry?

    International Nuclear Information System (INIS)

    Beamish, Basil; Kizil, Mehmet; Gu, Ming

    2013-01-01

    The last major advance in gas content measurement for coal seams was the introduction of the quick crush technique in the early 1990s. This is a laboratory test method that has proven very reliable over the years. Recent laboratory testing using a portable quick crushing device, known as the portable gas content analyser, has produced consistent gas content results for a set of core samples obtained from a single borehole that intersected four coal seams. The retained gas content values obtained for the seams show the same increasing gas content pattern and gas composition change with depth as the standard quick crush technique. Use of the portable gas content analyser provides the opportunity to produce rapid, reliable gas content measurement of coal that could be developed for assessing gas compliance cores and outburst-prone conditions at a mine site.

  11. Phenolic Content of Blends of Tempranillo with Graciano or Cabernet Sauvignon Wines Produced in Spain

    Directory of Open Access Journals (Sweden)

    María Monagas

    2006-01-01

    Full Text Available The effect of Graciano (GRA, Spanish valuable variety of limited production in Mediterranean countries vs. Cabernet Sauvignon (CS, world-wide known French variety on the phenolic content [total polyphenols (TP, total anthocyanins (TA, catechins (CAT and proanthocyanidins (PRO] of Tempranillo wines (TEM-BASE, a largely cultivated Spanish variety was studied in blends prepared with 25 and 10 % of each variety after 4, 6, 9, 16.5 and 23 months of bottle ageing. Significant differences among wines (blends and base wine according to the »blend« factor were observed for CAT and TA. Besides, although the evolution trend during wine ageing of different families of phenolic compounds studied was similar in the blends and base wine, different blends presented a faster anthocyanin disappearance kinetics than the base wine, probably due to their higher CAT content, which may favour the progress of certain anthocyanin condensation reactions during ageing in the bottle. This effect was slightly more pronounced in the TEM-GRA blends than in the TEM-CS ones. A further study of the phenolic composition of the monovarietal wines used for blending, as well as of the grapes (skins and seeds from which these wines were elaborated, revealed that the blending effect on CAT could be associated with higher concentration of these compounds in Graciano and Cabernet Sauvignon grape seeds in comparison with Tempranillo. Finally, the findings of this work scientifically confirm that, in terms of the phenolic content, Graciano wines possess properties similar to Cabernet Sauvignon for blending with Tempranillo.

  12. Chemical composition and microbial load of cheese produced using ...

    African Journals Online (AJOL)

    Aframomum sceptrum) on the chemical composition and microbial load of cheese was evaluated in a Completely Randomized Design. Cheese produced with 1% bear berry (Aframomum sceptrum) had the highest (P < 0.05) crude protein content ...

  13. Effects of adsorbates on Zircaloy oxidation in air

    International Nuclear Information System (INIS)

    Cho, Y.; Kim, Y-G.; Park, K.

    1997-01-01

    The air-oxidation of Zry and the effects of adsorbates on the oxidation are found by the intermittent measurement of the weight gain of specimens. NaC1 enhances the oxidation, where nonuniform stresses on the surface and C1 ions are the cause. LiOH also enhances the oxidation, where the initial oxide formed by LiOH seems to the reason. The effects of fluorides on oxidation are also measured. NaF is most harmful and KF follows next. LiF does not effect the oxidation of Zry. Diffusion of fluorides in oxide determines the enhancement. (author)

  14. Using muonium to probe the kinetics of the reaction between the H atom and OH"- in superheated water

    International Nuclear Information System (INIS)

    Ghandi, K.; Alcorn, C.; Brodovitch, J.-C.; Driedger, E.; Mozafari, M.; Percival, P.W.

    2011-01-01

    Operation of a supercritical-water-cooled nuclear reactor requires knowledge of water chemistry over a wide range of conditions. The considerable knowledge gap for conditions above the operating temperature of current-generation CANDU reactors is the target of this study. Since the H atom is difficult to probe at the desired temperatures and pressures, muonium is used as an alternative. In the current CANDU reactors, coolant pH is controlled using LiOH. We are studying how the rate constants for the reaction of muonium with LiOH and NaOH change with temperature and pressure. (author)

  15. Using muonium to probe the kinetics of the reaction between the H atom and OH{sup -} in superheated water

    Energy Technology Data Exchange (ETDEWEB)

    Ghandi, K.; Alcorn, C. [Mount Allison Univ., Sackville, NB (Canada); Brodovitch, J.-C. [Simon Fraser Univ., Burnaby, BC (Canada); Driedger, E. [Mount Allison Univ., Sackville, NB (Canada); Mozafari, M. [Simon Fraser Univ., Burnaby, BC (Canada); Percival, P.W. [Simon Fraser Univ., Burnaby, BC (Canada); TRIUMF, Vancouver, BC (Canada)

    2011-07-01

    Operation of a supercritical-water-cooled nuclear reactor requires knowledge of water chemistry over a wide range of conditions. The considerable knowledge gap for conditions above the operating temperature of current-generation CANDU reactors is the target of this study. Since the H atom is difficult to probe at the desired temperatures and pressures, muonium is used as an alternative. In the current CANDU reactors, coolant pH is controlled using LiOH. We are studying how the rate constants for the reaction of muonium with LiOH and NaOH change with temperature and pressure. (author)

  16. Gas condensate--raw material for producing liquid paraffin hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Aliyeva, R.B.; Alikishi-Zade, G.Yu.; Kuliyev, A.M.; Leonidov, A.N.; Pereverzev, A.N.

    1980-01-01

    The problem of efficient utilization of gas condensates as raw material for removal of a valuable product, liquid paraffins, is examined. A classification of gas condensates is given which is used as raw material for removing these hydrocarbons: gas condensate with high content of n-alkanes (25-40 mass percent), with average content (18-25 mass percent), with low content (12-18 mass percent), light weight fractions compositions, which do not contain fractions up to 200/sup 0/, and also, content ofless than 12% n-alkanes. Gas condensate I-III groups are 30% of the total reserve of gas condensate. Liquid paraffins hydrocarbons, produced from fractions of diesel fuel, which has been removed from Shatlyk gas condensate under conditions which simulate virtual processes of caramide deparaffinization meet all requirements without additional refining.

  17. Fissile Content Assay of Spent Fuel Using LSDS System

    International Nuclear Information System (INIS)

    Jeon, Ju Young; Lee, Yong Deok; Park, Chang Je

    2016-01-01

    About 1.5 % fissile materials still exist in the spent fuel. Therefore, for reutilization of fissile materials in spent fuel at SFR, resource material is produced through the pyro process. Fissile material contents in the resource material must be analyzed before fabricating SFR fuel for reactor safety and economics. The new technology for an isotopic fissile material content assay is under development at KAERI using a lead slowing down spectrometer (LSDS). LSDS is very sensitive to distinguish fission signals from each fissile isotope in spent and recycled fuel. In an assay of fissile content of spent fuel and recycled fuel, an intense radiation background gives limits the direct analysis of fissile materials. However, LSDS is not influenced by such a radiation background in a fissile assay. Based on the decided LSDS geometry set up, a self shielding parameter was calculated at the fuel assay zone by introducing spent fuel or pyro produced nuclear material. When nuclear material is inserted into the assay area, the spent fuel assembly or pyro recycled fuel material perturbs the spatial distribution of slowing down neutrons in lead and the prompt fast fission neutrons produced by fissile materials are also perturbed. The self shielding factor is interpreted as how much of the absorption is created inside the fuel area when it is in the lead. The self shielding effect provides a non-linear property in the isotopic fissile assay. When the self shielding is severe, the assay system becomes more complex and needs a special parameter to treat this non linear effect. Additionally, an assay of isotopic fissile content will contribute to an accuracy improvement of the burn-up code and increase the transparency and credibility for spent fuel storage and usage, as internationally increasing demand. The fissile contents result came out almost exactly with relative error ∼ 2% in case of Pu239, Pu241 for two different plutonium contents. In this study, meaningful results were

  18. Genome Sequence and Composition of a Tolyporphin-Producing Cyanobacterium-Microbial Community

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, Rebecca-Ayme; Zhang, Yunlong; Zhang, Ran; Williams, Philip G.; Lindsey, Jonathan S.; Miller, Eric S.; Nojiri, Hideaki

    2017-07-28

    ABSTRACT

    The cyanobacterial culture HT-58-2 was originally described as a strain ofcontent content-type='genus-species'>Tolypothrix nodosacontent>with the ability to produce tolyporphins, which comprise a family of distinct tetrapyrrole macrocycles with reported efflux pump inhibition properties. Upon reviving the culture from what was thought to be a nonextant collection, studies of culture conditions, strain characterization, phylogeny, and genomics have been undertaken. Here, HT-58-2 was shown by 16S rRNA analysis to closely align withcontent content-type='genus-species'>Brasilonema>strains and not withcontent content-type='genus-species'>Tolypothrix>isolates. Light, fluorescence, and scanning electron microscopy revealed cyanobacterium filaments that are decorated with attached bacteria and associated with free bacteria. Metagenomic surveys of HT-58-2 cultures revealed a diversity of bacteria dominated bycontent content-type='genus-species'>Erythrobacteraceae>, 97% of which arecontent content-type='genus-species'>Porphyrobacter>species. A dimethyl sulfoxide washing procedure was found to yield enriched cyanobacterial DNA (presumably by removing community bacteria) and sequence data sufficient for genome assembly. The finished, closed HT-58-2Cyano genome consists of 7.85 Mbp (42.6% G+C) and contains 6,581 genes. All genes for biosynthesis of tetrapyrroles (e.g., heme, chlorophylla, and phycocyanobilin) and almost all for cobalamin were identified dispersed throughout the chromosome. Among the 6,177 protein-encoding genes, coding sequences (CDSs) for all but two of the eight enzymes for conversion of glutamic acid to protoporphyrinogen IX also were found within one major gene cluster. The cluster also includes 10 putative genes (and one hypothetical gene) encoding proteins with

  19. Method for producing fluorinated diamond-like carbon films

    Science.gov (United States)

    Hakovirta, Marko J.; Nastasi, Michael A.; Lee, Deok-Hyung; He, Xiao-Ming

    2003-06-03

    Fluorinated, diamond-like carbon (F-DLC) films are produced by a pulsed, glow-discharge plasma immersion ion processing procedure. The pulsed, glow-discharge plasma was generated at a pressure of 1 Pa from an acetylene (C.sub.2 H.sub.2) and hexafluoroethane (C.sub.2 F.sub.6) gas mixture, and the fluorinated, diamond-like carbon films were deposited on silicon substrates. The film hardness and wear resistance were found to be strongly dependent on the fluorine content incorporated into the coatings. The hardness of the F-DLC films was found to decrease considerably when the fluorine content in the coatings reached about 20%. The contact angle of water on the F-DLC coatings was found to increase with increasing film fluorine content and to saturate at a level characteristic of polytetrafluoroethylene.

  20. The Social Content Strategy of the ATLAS Experiment

    CERN Document Server

    Sidoti, Antonio; The ATLAS collaboration

    2018-01-01

    Social media is an essential tool for communicating particle physics results to a wide audience. This presentation will explore how the nature of social media platforms has impacted the content being shared across them, and the subsequent effect this has had on the user experience. The ATLAS Experiment has adapted its communication strategy to match this social media evolution, producing content specifically targeting this emerging audience. The success of this approach is examined and the effect on user experience is evaluated.

  1. Secondary Metabolite Content in Roots and Callus of Paeonia Anomala L.

    Directory of Open Access Journals (Sweden)

    A.A. ZARIPOVA

    2014-06-01

    Full Text Available Taking into account the fact that in the process of introduction in vitro culture the change of secondary metabolite content may take place we compared the chemical composition of plant material of wild-growing plants of Paeonia anomala introduced and produced using the methods of clonal micropropagation, callus tissue.The content of phenolic compounds, that is catechins and gallatos was compared. Paeoniflorin content was estimated by direct spectrophotometry of methanol extracts (λ = 231,7 nm, ε 1% 1 sm = 265.4. Integral characteristic of the obtained extracts was received by comparison of absorption spectra using spectrophotometer SP - 121 within wave diapason 300 - 460 nm.Light absorption curves of methanol extracts had two distinct peaks at λ = 232 nm and λ = 275 nm typical of paeoniflorin. Paeoniflorin content was 80 % higher in young peony roots than in control plant. This glycoside content in callus culture was 44 % higher than in wild-growing plant roots and 26 % lower than in plantlet roots.The use of ethanol as extragent showed a higher content of extracted substances in callus tissue. The comparison of the obtained spectra in the region corresponding to phenolic compound absorption shows the highest phenolic compound content in callus tissue and young plant roots. Judging by light absorption maximum it may be phenolic acids. The lowest phenolic compound content was determined in adult wild-growing plant roots, where a high phlobaphene content was visually observed.The conducted research confirms the fact that callus culture of Paeonia anomala L. is a perspective producer of monoterpene glycosides and phenolic compounds. Extracts from plantlets and callus culture exceed in biological active substance content rootstock extracts of open air plants.

  2. Measuring the gypsum content of C&D debris fines.

    Science.gov (United States)

    Musson, Stephen E; Xu, Qiyong; Townsend, Timothy G

    2008-11-01

    Construction and demolition (C&D) debris recycling facilities often produce a screened material intended for use as alternative daily cover (ADC) at active landfills or for shaping and grading at closed landfills. This product contains soil and small pieces of wood, concrete, gypsum drywall, shingles and other components of C&D debris. Concerns have been raised over the contribution of gypsum drywall in C&D debris fines to odor problems at landfills where the product is used. To address such concerns, limitations may be placed on the percentage of gypsum (or sulfate) that can occur, and standardized testing procedures are required to permit valid compliance testing. A test procedure was developed for measuring the gypsum content in C&D debris fines. The concentration of sulfate leached in an aqueous solution was used to estimate the initial gypsum content of the sample. The impact of sample size and leaching time were evaluated. Precision and accuracy increased with increasing gypsum content. Results from replicate samples had an average relative standard deviation of 9%. The gypsum content of fines obtained from different facilities in the US varied widely from 1% to over 25%. These variations not only occurred between differing facilities, but within batches produced within a single facility.

  3. A New Method to Produce Ni-Cr Ferroalloy Used for Stainless Steel Production

    Science.gov (United States)

    Chen, Pei-Xian; Chu, Shao-Jun; Zhang, Guo-Hua

    2016-08-01

    A new electrosilicothermic method has been proposed in the present paper to produce Ni-Cr ferroalloy, which can be used for the production of 300 series stainless steel. Based on this new process, the Ni-Si ferroalloy is first produced as the intermediate alloy, and then the desiliconization process of Ni-Si ferroalloy melt with chromium concentrate is carried out to generate Ni-Cr ferroalloy. The silicon content in the Ni-Si ferroalloy produced in the submerged arc furnace should be more than 15 mass% (for the propose of reducing dephosphorization), in order to make sure the phosphorus content in the subsequently produced Ni-Cr ferroalloy is less than 0.03 mass%. A high utilization ratio of Si and a high recovery ratio of Cr can be obtained after the desiliconization reaction between Ni-Si ferroalloy and chromium concentrate in the electric arc furnace (EAF)-shaking ladle (SL) process.

  4. Low Temperature Synthesis, Chemical and Electrochemical Characterization of LiNi(x)Co(1-x)O2 (0 less than x less than 1)

    Science.gov (United States)

    Nanjundaswamy, K. S.; Standlee, D.; Kelly, C. O.; Whiteley, R. V., Jr.

    1997-01-01

    A new method of synthesis for the solid solution cathode materials LiNi(x)Co(1-x)O2 (0 less than x less than 1) involving enhanced reactions at temperatures less than or equal to 700 deg. C, between metal oxy-hydroxide precursors MOOH (M = Ni, Co) and Li-salts (Li2CO3, LiOH, and LiNO3) has been investigated. The effects of synthesis conditions and sources of Li, on phase purity, microstructure, and theoretical electrochemical capacity (total M(3+) content) are characterized by powder X-ray diffraction analysis, scanning electron microscopy, chemical analysis and room temperature magnetic susceptibility. An attempt has been made to correlate the electrochemical properties with the synthesis conditions and microstructure.

  5. Preliminary evaluation of fuel oil produced from pyrolysis of low ...

    African Journals Online (AJOL)

    MICHAEL

    The wax content decreases as temperature increases .The highest quantity ... polyethylene are generated . The producers of ... increase in the volume of waste generated daily by its usage in .... aviation industry and other domestic fuel users.

  6. Novel determination of surface temperature of lithium hydride hydrolysis using DRIFT spectroscopy

    International Nuclear Information System (INIS)

    Awbery, Roy P.; Tsang, S.C.

    2008-01-01

    Diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy has been used to show how increasing temperature causes the hydroxyl band of LiOH to shift linearly and reversibly towards lower wavenumbers. The band shift with temperature was used to determine the surface temperature of LiH when exposed to water vapour at 158, 317, 793 and >1900 Pa (5%, 10%, 25% and >60% relative humidity), the exothermic hydrolysis reaction resulting in surface temperature increases of up to 50 deg. C. The rate of surface heating was found to increase slightly with increasing water vapour exposures up to 793 Pa, demonstrating that the LiH hydrolysis reaction rate was dependent upon the partial pressure of water vapour. The growth of surface LiOH appeared to significantly slow down further reaction until the water vapour exposure was increased beyond 1900 Pa, when formation of hydrated LiOH occurred. The effect of temperature on detectors was also investigated showing that baselines shifted towards higher intensities with increasing temperature when measured with a DTGS detector and towards lower intensities with an MCT detector, over the temperature range 25-450 deg. C

  7. Effects of magnesium contents in ZnMgO ternary alloys grown by molecular beam epitaxy

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Sheng-Yao, E-mail: shenghu2729@yahoo.com [Department of Digital Technology Design, Tungfang Design Institute, Hunei, Kaohsiung 82941, Taiwan (China); Chou, Wu-Ching [Department of Electrophysics, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Weng, Yu-Hsiang [Department of Electrical Engineering, National Taiwan Ocean University, Keelung 20224, Taiwan (China)

    2015-07-05

    Highlights: • ZnMgO alloys with different Mg contents have been produced by MBE. • Optical and structural properties have been measured and investigated. • Stress is tensile and is increased as the increasing of Mg contents. • The asymmetric behavior of the Raman mode was influenced due to the Mg contents. - Abstract: Ternary alloys of ZnMgO samples with different magnesium contents have been grown by molecular beam epitaxy on the sapphire substrates. Room temperature photoluminescence energy of ZnMgO shifted as high as 3.677 eV by increasing Mg contents corresponding to the higher Urbach average localization energy which indicates more randomness in the alloys with higher Mg contents. XRD results are also verified that the c-axis length decreases as the increasing Mg contents linking to the increased tensile stress produced by the Mg atoms. Raman spectra analyzed by the spatial correlation model to describe that the linewidth Γ is decreased but the correlation length L is increased as the increasing of Mg contents.

  8. Effects of magnesium contents in ZnMgO ternary alloys grown by molecular beam epitaxy

    International Nuclear Information System (INIS)

    Hu, Sheng-Yao; Chou, Wu-Ching; Weng, Yu-Hsiang

    2015-01-01

    Highlights: • ZnMgO alloys with different Mg contents have been produced by MBE. • Optical and structural properties have been measured and investigated. • Stress is tensile and is increased as the increasing of Mg contents. • The asymmetric behavior of the Raman mode was influenced due to the Mg contents. - Abstract: Ternary alloys of ZnMgO samples with different magnesium contents have been grown by molecular beam epitaxy on the sapphire substrates. Room temperature photoluminescence energy of ZnMgO shifted as high as 3.677 eV by increasing Mg contents corresponding to the higher Urbach average localization energy which indicates more randomness in the alloys with higher Mg contents. XRD results are also verified that the c-axis length decreases as the increasing Mg contents linking to the increased tensile stress produced by the Mg atoms. Raman spectra analyzed by the spatial correlation model to describe that the linewidth Γ is decreased but the correlation length L is increased as the increasing of Mg contents

  9. Cellulose gels produced in room temperature ionic liquids by ionizing radiation

    International Nuclear Information System (INIS)

    Kimura, Atsushi; Nagasawa, Naotsugu; Taguchi, Mitsumasa

    2014-01-01

    Cellulose-based gels were produced in room temperature ionic liquids (RTILs) by ionizing radiation. Cellulose was dissolved at the initial concentration of 20 wt% in 1-ethyl-3-methylimidazolium (EMI)-acetate or N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium (DEMA)-formate with a water content of 18 wt%, and irradiated with γ-rays under aerated condition to produce new cellulose gels. The gel fractions of the cellulose gels obtained in EMI-acetate and DEMA-formate at a dose of 10 kGy were 13% and 19%, respectively. The formation of gel fractions was found to depend on the initial concentration of cellulose, water content, and irradiation temperature. The obtained gel readily absorbed water, methanol, ethanol, dichloromethane, N,N-dimethylacetamide, and RTILs. - Highlights: • Cellulose gels were produced in room temperature ionic liquids (RTILs). • Water plays a crucial role in the cross-linking reaction. • Cellulose gels swollen with RTILs show good electronic conductivity (3.0 mS cm −1 )

  10. SAIChE Conference Poster: Irradiation treatment of dissolving pulps produced in South Africa

    CSIR Research Space (South Africa)

    Ocwelwang, A

    2014-07-01

    Full Text Available stream_source_info Ocwelwang_2014_ABSTRACT.pdf.txt stream_content_type text/plain stream_size 876 Content-Encoding ISO-8859-1 stream_name Ocwelwang_2014_ABSTRACT.pdf.txt Content-Type text/plain; charset=ISO-8859-1 2014... International Conference on Chemical Thermodynamics and South African Institution of Chemical Engineering Conference, Durban, South Africa, 27 July - 1 August 2014 SAIChE Conference Poster: Irradiation treatment of dissolving pulps produced in South...

  11. Thermal energy storage material thermophysical property measurement and heat transfer impact

    Science.gov (United States)

    Tye, R. P.; Bourne, J. G.; Destarlais, A. O.

    1976-01-01

    The thermophysical properties of salts having potential for thermal energy storage to provide peaking energy in conventional electric utility power plants were investigated. The power plants studied were the pressurized water reactor, boiling water reactor, supercritical steam reactor, and high temperature gas reactor. The salts considered were LiNO3, 63LiOH/37 LiCl eutectic, LiOH, and Na2B4O7. The thermal conductivity, specific heat (including latent heat of fusion), and density of each salt were measured for a temperature range of at least + or - 100 K of the measured melting point. Measurements were made with both reagent and commercial grades of each salt.

  12. Effects of moisture barrier and initial moisture content on the storage ...

    African Journals Online (AJOL)

    The two factors examined were moisture barrier at three levels namely: thick lining, thin lining and non-lining. The other factor included initial moisture content of the produce, namely, turgid and partially wilted. Partial wilting of the produce was achieved by exposing freshly harvested materials at ambient temperature to dry ...

  13. Using the DOM Tree for Content Extraction

    Directory of Open Access Journals (Sweden)

    David Insa

    2012-10-01

    Full Text Available The main information of a webpage is usually mixed between menus, advertisements, panels, and other not necessarily related information; and it is often difficult to automatically isolate this information. This is precisely the objective of content extraction, a research area of widely interest due to its many applications. Content extraction is useful not only for the final human user, but it is also frequently used as a preprocessing stage of different systems that need to extract the main content in a web document to avoid the treatment and processing of other useless information. Other interesting application where content extraction is particularly used is displaying webpages in small screens such as mobile phones or PDAs. In this work we present a new technique for content extraction that uses the DOM tree of the webpage to analyze the hierarchical relations of the elements in the webpage. Thanks to this information, the technique achieves a considerable recall and precision. Using the DOM structure for content extraction gives us the benefits of other approaches based on the syntax of the webpage (such as characters, words and tags, but it also gives us a very precise information regarding the related components in a block, thus, producing very cohesive blocks.

  14. Operando X-ray diffraction analysis for a glyme-based Li-O_2 battery

    International Nuclear Information System (INIS)

    Yogi, C.; Takao, N.; Kubobuchi, K.; Matsumoto, M.; Mogi, M.; Imai, H.; Watanabe, T.

    2016-01-01

    We investigated the effect of the carbon species in the air (oxygen) electrode, electrolyte concentration, and humidity in the supplied O_2 gas on the Li-O_2 reactions by using the operando XRD analysis. Regarding carbon species, we found that the over-potentials in the galvanostatic discharge-charge process were suppressed when using the KB carbon in the air electrode. The results of operando XRD measurements revealed that the Li_2O_2 formed on the KB had the smaller crystalline or more amorphous like structures, which could be one reason for faster reaction kinetics of Li_2O_2 dissolution. The discharge-charge curves of the cells with different concentration of LiTFSI/(G4)_n electrolyte showed the slight difference but less differences in the Li_2O_2 formation and dissolution behaviors. In addition to the nature of Li_2O_2 products, reaction of Li-salts would also have ineligible effects. We also found that the higher humidity in oxygen produced more the LiOH and promoted the Li_2O_2 dissolution, which indicate that the LiOH formation could affect the Li_2O_2 morphologies or surface chemistries. Our present results demonstrated that the operando XRD measurement are useful for analyzing the reaction mechanism of Li-O_2 battery.

  15. Method of producing pitch (distillation residue)

    Energy Technology Data Exchange (ETDEWEB)

    Stepanenko, M.A.; Belkina, T.V.; Krysin, V.P.

    1979-08-15

    A method is proposed for producing pitch by mixing hard coal pitch with anthracene fraction and thermal treatment of the mixture. The method is distinguished in that in order to increase the quality of the pitch, the anthracene fraction is subjected to thermal treatment at 250-300/sup 0/ for 10-13 hours in the presence of air. This duration of heat treatment allows one to build up in the anthracene fraction up to 20-24% of material which is not soluble and toluene, without the formation of products which are not soluble in quinoline. The fraction prepared in this manner is inserted into the initial pitch in the ratio 1:2 up to 1:9, the mixture is subject to heat treatment at temperature 360-380/sup 0/ and air consumption 7-91/kgX hours until the production of pitch with softening temperature of 85-90/sup 0/. As the initial raw material we used pitch with softening temperature of 60/sup 0/, content of substances which are not soluble in quinoline, 2.0% which are not soluble and toluene 20.6% and coking residue of 49.2%. Example. 80 grams of anthracene fraction is added to 320 grams of pitch. The anthracene fraction is subjected previously to heat treatment at 300/sup 0/ for 13 hours in the presence of air, supplied in the amount of 9 liters per hour. As a result of the heat treatment of the content of materials which are not soluble in toluence in the anthracene fraction is 24.0%, in quinoline it is 0.1%. The ratio of a pitch and thermally treated anthracene fraction in the mixture was 4:l. The produced mixture was subjected to heat treatment at 360/sup 0/ for 1.5 hours with air supply in the amount of 7 liters/ kilograms/hours. Pitch is produced with the following characteristics: softening temperature 88/sup 0/, content of substances which are not soluble in toluene 32.5%, in quinilone, 6.0%, coking residue, 56.7%. The invention can be used in the chemical coking and petrochemical industry.

  16. Is there a feeding strategy to increase milk casein content?

    Directory of Open Access Journals (Sweden)

    A. Formigoni

    2010-04-01

    Full Text Available Because more than 60% of milk produced in Italy is transformed into cheese, milk economical value strongly depends on cheese yield. Among the factors that influence cheese yield, milk casein and fat content plays a major role: when milk is converted into Grana Padano and Parmigiano reggiano, three grams of seasoned cheese are produced from one gram of milk casein.....

  17. Standards-based Content Resources: A Prerequisite for Content Integration and Content Interoperability

    Directory of Open Access Journals (Sweden)

    Christian Galinski

    2010-05-01

    Full Text Available Objective: to show how standards-based approaches for content standardization, content management, content related services and tools as well as the respective certification systems not only guarantee reliable content integration and content interoperability, but also are of particular benefit to people with special needs in eAccessibility/eInclusion. Method: document MoU/MG/05 N0221 ''Semantic Interoperability and the need for a coherent policy for a framework of distributed, possibly federated repositories for all kinds of content items on a world-wide scale''2, which was adopted in 2005, was a first step towards the formulation of global interoperability requirements for structured content. These requirements -based on advanced terminological principles- were taken up in EU-projects such as IN-SAFETY (INfrastructure and SAFETY and OASIS (Open architecture for Accessible Services Integration and Standardization. Results: Content integration and content interoperability are key concepts in connection with the emergence of state-of-the-art distributed and federated databases/repositories of structured content. Given the fact that linguistic content items are increasingly combined with or embedded in non-linguistic content items (and vice versa, a systemic and generic approach to data modelling and content management has become the order of the day. Fulfilling the requirements of capability for multilinguality and multimodality, based on open standards makes software and database design fit for eAccessibility/eInclusion from the outset. It also makes structured content capable for global content integration and content interoperability, because it enhances its potential for being re-used and re-purposed in totally different eApplications. Such content as well as the methods, tools and services applied can be subject to new kinds of certification schemes which also should be based on standards. Conclusions: Content must be totally reliable in some

  18. Fatty Acid Content of Indonesian Aquatic Microalgae

    Directory of Open Access Journals (Sweden)

    TRI PRARTONO

    2010-12-01

    Full Text Available High utilization of fossil fuel increases the level of carbon dioxide in the atmosphere and results in global warming phenomenon. These things establish the world's thought to look for the other alternative energy that can reduce the use of fossil fuel even to be replaced by the substitute. Recently, Indonesia has been doing the research of microalgae as a feedstock of an alternative biofuel. Fatty acid content that microalgae have is also high to produce biofuel. The steps used in this research is a 7 days cultivation, harvesting, extraction using hexane, and fatty acid identification using Gas Chromatography of microalgae species. Fatty acid component in some species such as Chlorella sp., Scenedesmus sp., Nannochloropsis sp., and Isochrysis sp. is between 0.21-29.5%; 0.11-25.16%; 0.30-42.32%; 2.06-37.63%, respectively, based on dry weight calculation. The high content of fatty acid in some species of microalgae showed the potential to be the feedstock of producing biofuel in overcoming the limited utilization from petroleum (fossil fuel presently.

  19. Ascorbic Acid Contents in Chili Peppers (Capsicum L.

    Directory of Open Access Journals (Sweden)

    Owk ANIEL KUMAR

    2009-12-01

    Full Text Available The genus Capsicum commonly known as chili pepper is a major spice crop and is almost cosmopolitan in distribution. The nutritive value of chili pepper is largely determined by ascorbic acid content. The fruits at five ripening stages viz., (M1, M2, M3, M4 and M5 from seventeen cultivars of Capsicum annuum L and one cultivar of Capsicum frutescens L were analyzed for ascorbic acid content. Among eighteen genotypes the C. annuum var. IC: 119262(CA2 showed higher ascorbic acid content (mg/100g FW i.e., 208.00.68 (M1, 231.00.66 (M2, 280.00.31 (M3, 253.00.34 (M4 and 173.70.27 (M5. The study revealed that the gradual increase in ascorbic acid content from green to red and subsequently declined in the lateral stages (red partially dried and red fully dried fruits. The variability of ascorbic acid content in the genotypes suggests that these selected genotypes may be use full as parents in hybridization programs to produce fruits with good nutritional values.

  20. Influence of Fiber Content on Mechanical and Morphological Properties of Woven Kenaf Reinforced PVB Film Produced Using a Hot Press Technique

    Directory of Open Access Journals (Sweden)

    Suhad D. Salman

    2016-01-01

    Full Text Available This work addresses the results of experimental investigation carried out on mechanical and morphological properties of plain woven kenaf fiber reinforced PVB film which was prepared by hot press technique. The composites were prepared with various fiber contents: 0%, 10%, 20%, 30%, 40%, 50%, and 60% (by weight, with the processing parameters 165°C, 20 min, and at a pressure of 8 MPa applied on the material. Tensile, flexural, and Charpy impact properties were studied as well as morphological properties of impact fracture surface. With the increase in kenaf fibers content up to 40%, the PVB composites have shown lower tensile and flexural strength accompanied with reduction in the ultimate strain of the composite. The results showed that impact properties were affected in markedly different ways by using various kenaf contents and decrease with the increase in kenaf fiber content up to 40%; however, high impact strength was observed even with 40% kenaf fiber content. Furthermore, scanning electron microscopy for impact samples was utilised to demonstrate the different failures in the fracture surfaces for various kenaf fibers contents.

  1. Letting go of the words writing web content that works

    CERN Document Server

    Redish, Janice (Ginny)

    2012-01-01

    Web site design and development continues to become more sophisticated an important part of this maturity originates with well laid out and well written content. Ginny Redish is a world-renowned expert on information design and how to produce clear writing in plain language for the web. All of the invaluable information that she  shared in the first edition is included with numerous new examples. New information on content strategy for web sites, search engine optimization (SEO), and social media will enhance the book's content making it once again the only book you need to own to o

  2. Applicability of the ''review of content'' under the law on standard terms and conditions to power availability and power supply contracts between producers and resellers; Die Anwendbarkeit der AGB-rechtlichen Inhaltskontrolle auf Leistungsvorhaltungs- und Stromliefervertraege zwischen Erzeuger und Weiterverkaeufer

    Energy Technology Data Exchange (ETDEWEB)

    Putzka, Florian

    2009-07-01

    This study deals with the applicability under the law on standard terms and conditions of the ''review of content'' to power availability and power supply contracts between producers and resellers. It addresses fundamental issues concerning the encroachment on the private autonomy of those involved as well as the hazard to the contract certainty of their contracts that is posed by the instrument of judicial review of content under the law on standard terms and conditions. The purpose of the study is to determine to what extent power availability and power supply contracts between producers and resellers are subject to a review of content by a civil judge, be it on the strength of the law on standard terms and conditions or through what is known as an extended review of content. Power supply contracts between power suppliers and final customers are left out of consideration here, even though the authors are aware of the fact that as a result of the amendment to the Energy Economy Law in 2005 and the ordinances following in its wake it is becoming more and more common for such contracts to be amenable to the law on standard terms and conditions.

  3. Preparation of Tritium from irradiated lithium compounds (study)

    International Nuclear Information System (INIS)

    1989-01-01

    The aim of the present study is the selection of a certain scheme for release, collection, measurement and analysis of Tritium as produced in Lithium compounds (Li 2 O, LiOH, Li 2 CO 3 LiF and some Lithium alloys) in accordance with the 6 Li(n, α)T reaction. Tritium technology is of vital concern to power reactor programmes as well as to fusion technology. Meanwhile the fields of activity include, tritium generation and mangement in fission and fusion reactors; enviromental studies, release modeling HT/HTO conversion and dose assessments, absorption/ deabsorption, monitoring and plant design; research and development, labeling, compatibility and physical chemical properties

  4. Preparation of Tritium from irradiated lithium compounds (study)

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The aim of the present study is the selection of a certain scheme for release, collection, measurement and analysis of Tritium as produced in Lithium compounds (Li[sub 2]O, LiOH, Li[sub 2]CO[sub 3] LiF and some Lithium alloys) in accordance with the [sup 6]Li(n, [alpha])T reaction. Tritium technology is of vital concern to power reactor programmes as well as to fusion technology. Meanwhile the fields of activity include, tritium generation and mangement in fission and fusion reactors; enviromental studies, release modeling HT/HTO conversion and dose assessments, absorption/ deabsorption, monitoring and plant design; research and development, labeling, compatibility and physical chemical properties.

  5. Analyzing Public Discourse: Using Media Content Analysis to Understand the Policy Process

    Science.gov (United States)

    Saraisky, Nancy Green

    2016-01-01

    One of the most basic and obvious sources of data for education policy analysis is text. This article discusses content analysis as an important part of the methodological toolbox for elucidating patterns and trends about education policy. Focusing specifically on media, I show how media content analysis can produce nuanced insights about the ways…

  6. Information content of poisson images

    International Nuclear Information System (INIS)

    Cederlund, J.

    1979-04-01

    One major problem when producing images with the aid of Poisson distributed quanta is how best to compromise between spatial and contrast resolution. Increasing the number of image elements improves spatial resolution, but at the cost of fewer quanta per image element, which reduces contrast resolution. Information theory arguments are used to analyse this problem. It is argued that information capacity is a useful concept to describe an important property of the imaging device, but that in order to compute the information content of an image produced by this device some statistical properties (such as the a priori probability of the densities) of the object to be depicted must be taken into account. If these statistical properties are not known one cannot make a correct choice between spatial and contrast resolution. (author)

  7. Chemical and ecotoxicological evaluation of biochar produced from residues of biogas production.

    Science.gov (United States)

    Stefaniuk, Magdalena; Oleszczuk, Patryk; Bartmiński, Piotr

    2016-11-15

    Analyses were carried out for biochars produced at three temperatures of pyrolysis (400, 600 and 800°C) from solid residue from biogas production (RBP). Separated and non-separated RBP from biogas plants employing different biogas production conditions were pyrolyzed. The contents of heavy metals and polycyclic aromatic hydrocarbons (PAHs) (16 PAH US EPA) were analyzed in biochars. The analyses showed that with an increased pyrolysis temperature, there was an increase in the contents of PAHs and of certain heavy metals (Cr, Cu, Cd, Pb and Mn). In the ecotoxicological tests, it was noted that the effect depended on the temperature of pyrolysis and on the feedstock from which the biochar was produced. The least harmful effect on the test organisms was from biochar produced by separated RBP in a biogas plant operating in mesophilic conditions. The most negative effect on the test organisms was characteristic of biochar produced from non-separated mesophilic RBP. This study shows that the main factors determining the level of toxicity of biochars produced from RBP towards various living organisms are both the method of feedstock production and the temperature at which the process of pyrolysis is conducted. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Evaluation of Non-Saccharomyces Yeasts for the Reduction of Alcohol Content in Wine

    Science.gov (United States)

    Contreras, A.; Hidalgo, C.; Henschke, P. A.; Chambers, P. J.; Curtin, C.

    2014-01-01

    Over recent decades, the average ethanol concentration of wine has increased, largely due to consumer preference for wine styles associated with increased grape maturity; sugar content increases with grape maturity, and this translates into increased alcohol content in wine. However, high ethanol content impacts wine sensory properties, reducing the perceived complexity of flavors and aromas. In addition, for health and economic reasons, the wine sector is actively seeking technologies to facilitate the production of wines with lower ethanol content. Nonconventional yeast species, in particular, non-Saccharomyces yeasts, have shown potential for producing wines with lower alcohol content. These yeast species, which are largely associated with grapes preharvest, are present in the early stages of fermentation but, in general, are not capable of completing alcoholic fermentation. We have evaluated 50 different non-Saccharomyces isolates belonging to 24 different genera for their capacity to produce wine with a lower ethanol concentration when used in sequential inoculation regimes with a Saccharomyces cerevisiae wine strain. A sequential inoculation of Metschnikowia pulcherrima AWRI1149 followed by an S. cerevisiae wine strain was best able to produce wine with an ethanol concentration lower than that achieved with the single-inoculum, wine yeast control. Sequential fermentations utilizing AWRI1149 produced wines with 0.9% (vol/vol) and 1.6% (vol/vol) (corresponding to 7.1 g/liter and 12.6 g/liter, respectively) lower ethanol concentrations in Chardonnay and Shiraz wines, respectively. In Chardonnay wine, the total concentration of esters and higher alcohols was higher for wines generated from sequential inoculations, whereas the total concentration of volatile acids was significantly lower. In sequentially inoculated Shiraz wines, the total concentration of higher alcohols was higher and the total concentration of volatile acids was reduced compared with those in

  9. Effect of Y2O3 Content on Microstructure of Gradient Bioceramic Composite Coating Produced by Wide-Band Laser Cladding

    Institute of Scientific and Technical Information of China (English)

    Liu Qibin; Zou Jianglong; Zheng Min; Dong Chuang

    2005-01-01

    To eliminate thermal stress and cracks in the process of laser cladding, a kind of bioceramic coating with gradient compositional design was prepared on the surface of Ti alloy by using wide-band laser cladding. And effect of Y2O3 content on gradient bioceramic composite coating was studied. The experimental results indicate that adding rare earth can refine grain. Different rare earth contents affect formation of HA and β-TCP in bioceramic coating. When the content of rare earth ranges from 0.4% to 0.6%, the active extent of rare earth in synthesizing HA and β-TCP is the best, which indicates that "monosodium glutamate" effect of rare earth plays a dominant role. However, when rare earth content is up to 0.8%, the amount of synthesizing HA and β-TCP in coating conversely goes down, which demonstrates that rare earth gradually losts its catalysis in manufacturing HA and β-TCP.

  10. External Correlates of the MMPI-2 Content Component Scales in Mental Health Inpatients

    Science.gov (United States)

    Green, Bradley A.; Handel, Richard W.; Archer, Robert P.

    2006-01-01

    External correlates of the Minnesota Multiphasic Personality Inventory-2 (MMPI-2) Content Component Scales were identified using an inpatient sample of 544 adults. The Brief Psychiatric Rating Scale (BPRS) and Symptom Checklist 90-Revised (SCL-90-R) produced correlates of the Content Component Scales, demonstrating external validity with…

  11. LSDS Development for Isotopic Fissile Content Assay

    International Nuclear Information System (INIS)

    Lee, Yong Deok; Park, Chang Je; Park, Geun Il; Lee, Jung Won; Song, Kee Chan

    2010-01-01

    Concerning the sustainable energy supply and green house effect, nuclear energy became the most feasible option to meet the energy demand in Korea. However, the production of the spent nuclear fuel is the inevitable situation. Since the first nuclear power plant started to produce the electricity in Korea, the accumulated amount of spent fuels exceeded 10k tomes recently. The accumulation of the spent fuels is the big issue in the society. Therefore, as an option which strengthens the nuclear proliferation resistance and reduces the amount of spent fuels, sodium fast reactor (SFR) program linked with pyro-processing is under development to re-use the PWR spent fuel and produce the energy. In the process, the produced metallic material involves uranium and TRU (transuranic; neptunium, plutonium, and americium). The uranium-TRU is used to fabricate SFR fuel. The burning the recycled fuel in the reactor is to solve the current spent fuel storage problem and to minimize the actinides accumulation having long half-life. Generally, the spent fuel from PWR has unburned ∼1 % U235, produced ∼0.5 % plutonium from decay chain, ∼3 % fission products, ∼ 0.1 % minor actinides (MA) and uranium remainder. About 1.5 % fissile materials still exist in the spent fuel. Therefore, spent fuel is not only waste but energy resource. The direct and isotopic fissile content assay is the crucial technology for the spent fuel reuse. Additionally, the fissile content analysis will contribute to the optimum storage design and safe spent fuel management. Several nondestructive technologies have been developed for the spent fuel assay; gamma ray measurement, passive and active neutron measurements. Spent fuel emits intense gamma rays and neutrons by (a, n) and spontaneous fission. This intense background has the limitation on the direct analysis of fissile materials. Recently, to analyze the individual fissile content, leadslowing down spectrometer (LSDS) has been being developed in Korea

  12. 7 CFR 205.305 - Multi-ingredient packaged products with less than 70 percent organically produced ingredients.

    Science.gov (United States)

    2010-01-01

    ... Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... organically produced ingredients may only identify the organic content of the product by: (1) Identifying each... statement, displaying the product's percentage of organic contents on the information panel. (b...

  13. Cascade reactor: granule fabrication processes

    International Nuclear Information System (INIS)

    Erlandson, O.D.; Winkler, E.O.; Maya, I.; Pitts, J.H.

    1985-01-01

    A key feature of Cascade is the granular blanket. Of the many blanket material options open to Cascade, fabrication of Li 2 O granules was felt to offer the greatest challenge. The authors explored available methods for initial Li 2 O granule fabrication. They identified three cost-effective processes for fabricating Li 2 O granules: the VSM drop-melt furnace process, which is based on melting and spheroidizing irregularly shaped Li 2 O feed granules; the LiOH process, which spheroidizes liquefied LiOH and uses GA Technologies' sphere-forming procedures; and the Li 2 CO 3 sol-gel process, used for making spherical fuel particles for the high-temperature gas-cooled reactor (HTGR). Each process is described below

  14. Compelling Untruths: Content Borrowing and Vivid False Memories

    Science.gov (United States)

    Lampinen, James Michael; Meier, Christopher R.; Arnal, Jack D.; Leding, Juliana K.

    2005-01-01

    False memories are sometimes accompanied by surprisingly vivid experiential detail that makes them difficult to distinguish from actual memories. Such strikingly real false memories may be produced by a process called content borrowing in which details from presented items are errantly borrowed to corroborate the occurrence of the false memory…

  15. Comparative experiments on polymer degradation technique of produced water of polymer flooding oilfield

    Science.gov (United States)

    Chen, Rong; Qi, Mei; Zhang, Guohui; Yi, Chenggao

    2018-02-01

    The application of polymer flooding technology in oilfields can result in polymer content increased in produced water. This increasing made produced water quality become poor. The efficiency of produced water processing decreased significantly. Processed water quality seriously exceeded criterion’s stipulation. The presence of the polymer in produced water is the main reason for more difficulties in processing of produced water, therefore the polymer degradation technology is a key coefficient in produced water processing for polymer flooding oilfields. We evaluated several physical and chemical polymer degradation methods with the solution of separated water from polymer flooding oilfields and hydrolyzed polyacrylamide. The experiment results can provide a basis for produced water processing technologies application in polymer flooding oilfields.

  16. 40 CFR 80.340 - What standards and requirements apply to refiners producing gasoline by blending blendstocks into...

    Science.gov (United States)

    2010-07-01

    ... to refiners producing gasoline by blending blendstocks into previously certified gasoline (PCG)? 80... gasoline by blending blendstocks into previously certified gasoline (PCG)? (a) Any refiner who produces...) The sulfur content and volume of each batch of gasoline produced is that of the butane the refiner...

  17. Encounters and Content Sharing in an Urban Village: Reading Texts Through an Archaeological Lens

    Science.gov (United States)

    Garcia, Nicole; Foth, Marcus; Hearn, Greg

    Archaeology provides a framework of analysis and interpretation that is useful for disentangling the textual layers of a contemporary lived-in urban space. The producers and readers of texts may include those who planned and developed the site and those who now live, visit, and work there. Some of the social encounters and content sharing between these people may be artificially produced or manufactured in the hope that certain social situations will occur. Others may be serendipitous. With archaeology's original focus on places that are no longer inhabited, it is often only the remaining artifacts and features of the built environment that form the basis for interpreting the social relationships of past people. Our analysis, however, is framed within a contemporary notion of archaeological artifacts in an urban setting. Unlike an excavation, where the past is revealed through digging into the landscape, the application of landscape archaeology within a present day urban context is necessarily more experiential, visual, and based on recording and analyzing the physical traces of social encounters and relationships between residents and visitors. These physical traces are present within the creative content, and the built and natural elements of the environment. This chapter explores notions of social encounters and content sharing in an urban village by analyzing three different types of texts: the design of the built environment; content produced by residents through a geospatial web application; and, print and online media produced in digital storytelling workshops.

  18. Identify Web-page Content meaning using Knowledge based System for Dual Meaning Words

    OpenAIRE

    Sinha, Sukanta; Dattagupta, Rana; Mukhopadhyay, Debajyoti

    2012-01-01

    Meaning of Web-page content plays a big role while produced a search result from a search engine. Most of the cases Web-page meaning stored in title or meta-tag area but those meanings do not always match with Web-page content. To overcome this situation we need to go through the Web-page content to identify the Web-page meaning. In such cases, where Webpage content holds dual meaning words that time it is really difficult to identify the meaning of the Web-page. In this paper, we are introdu...

  19. Influence of Sweetness and Ethanol Content on Mead Acceptability

    Directory of Open Access Journals (Sweden)

    Gomes Teresa

    2015-06-01

    Full Text Available Mead is a traditional alcoholic beverage obtained by fermenting mead wort; however, its production still remains frequently an empirical exercise. Different meads can be produced, depending on fermentation conditions. Nevertheless, to date few studies have been developed on factors that may influence mead quality. The main objective of this work was to study the influence of sweetness and ethanol content on mead acceptability. Different meads were produced with two sweetness levels (sweet and dry meads and three ethanol contents (18, 20, 22% (v/v, adjusted by brandy addition. Afterwards, meads acceptability was evaluated by sensory analysis through a consumers’ panel (n=108 along with chemical analysis by HPLC-RID of glucose, fructose, ethanol, glycerol and acetic acid. The sweet (75 gglucose+fructose/L and dry (23 gglucose+fructose/L meads presented glycerol contents equal to 5.10±0.54 and 5.96±0.95 g/L, respectively, that were desirable since glycerol improves mead quality. Low concentrations of acetic acid were determined (0.46±0.08 and 0.57±0.09 g/L, avoiding the vinegar off-character. Concerning sensory analysis, the alcohol content of mead had no effect on the sensory attributes studied, namely, aroma, sweetness, flavour, alcohol feeling and general appreciation. Regarding sweetness, the “sweet meads” were the most appreciated by the consumers (score of 5.4±2.56, whereas the “dry meads” (score of 2.7±2.23 showed low acceptability. In conclusion, this work revealed that sweetness is a sensory key attribute for mead acceptance by the consumers, whereas ethanol content (18 to 22% (v/v is not.

  20. Suitable alkaline for graphene peeling grown on metallic catalysts using chemical vapor deposition

    Science.gov (United States)

    Karamat, S.; Sonuşen, S.; Çelik, Ü.; Uysallı, Y.; Oral, A.

    2016-04-01

    In chemical vapor deposition, the higher growth temperature roughens the surface of the metal catalyst and a delicate method is necessary for the transfer of graphene from metal catalyst to the desired substrates. In this work, we grow graphene on Pt and Cu foil via ambient pressure chemical vapor deposition (AP-CVD) method and further alkaline water electrolysis was used to peel off graphene from the metallic catalyst. We used different electrolytes i.e., sodium hydroxide (NaOH), potassium hydroxide (KOH), lithium hydroxide (LiOH) and barium hydroxide Ba(OH)2 for electrolysis, hydrogen bubbles evolved at the Pt cathode (graphene/Pt/PMMA stack) and as a result graphene layer peeled off from the substrate without damage. The peeling time for KOH and LiOH was ∼6 min and for NaOH and Ba(OH)2 it was ∼15 min. KOH and LiOH peeled off graphene very efficiently as compared to NaOH and Ba(OH)2 from the Pt electrode. In case of copper, the peeling time is ∼3-5 min. Different characterizations like optical microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy were done to analyze the as grown and transferred graphene samples.

  1. Plants with modified lignin content and methods for production thereof

    Science.gov (United States)

    Zhao, Qiao; Chen, Fang; Dixon, Richard A.

    2014-08-05

    The invention provides methods for decreasing lignin content and for increasing the level of fermentable carbohydrates in plants by down-regulation of the NST transcription factor. Nucleic acid constructs for down-regulation of NST are described. Transgenic plants are provided that comprise reduced lignin content. Plants described herein may be used, for example, as improved biofuel feedstock and as highly digestible forage crops. Methods for processing plant tissue and for producing ethanol by utilizing such plants are also provided.

  2. The FCC process as a producer of light olefins

    International Nuclear Information System (INIS)

    Yung, K.Y.; Yanik, S.; O'Connor, P.; Pouwels, C.

    1992-01-01

    To reduce emissions from the gasoline engine, aromatics content and vapor pressure of the motor gasoline pool will be reduced and a minimum amount of oxygen will be mandated. This reformulation will limit the application of high octane components like benzene, toluene and butanes and will require the use of oxygenates. To compensate for the loss in octane, the use of alkylate and, of course also oxygenates will grow. The Fluid Catalytic Cracking Unit is, as producer of (olefinic) propanes, butanes and pentanes, an important feedstock producer for alkylate and oxygenate producing process. Hence, process adjustments and FCC catalyst formations to increase the yield of above desirable light products are of prime importance and will be dealt with in this paper

  3. Lithium inclusion in indium metal-organic frameworks showing increased surface area and hydrogen adsorption

    Directory of Open Access Journals (Sweden)

    Mathieu Bosch

    2014-12-01

    Full Text Available Investigation of counterion exchange in two anionic In-Metal-Organic Frameworks (In-MOFs showed that partial replacement of disordered ammonium cations was achieved through the pre-synthetic addition of LiOH to the reaction mixture. This resulted in a surface area increase of over 1600% in {Li [In(1,3 − BDC2]}n and enhancement of the H2 uptake of approximately 275% at 80 000 Pa at 77 K. This method resulted in frameworks with permanent lithium content after repeated solvent exchange as confirmed by inductively coupled plasma mass spectrometry. Lithium counterion replacement appears to increase porosity after activation through replacement of bulkier, softer counterions and demonstrates tuning of pore size and properties in MOFs.

  4. Mortar modified with sulfonated polystyrene produced from waste plastic cups

    Directory of Open Access Journals (Sweden)

    L. A. C. MOTTA

    Full Text Available Abstract In this work, we studied the addition of sulfonated polystyrene produced from waste plastic cups as an admixture for mortars. Mortars were analyzed with polystyrene content of 0.0; 0.2; 0.6; 1.0 and 1.4% in relation to the cement mass. The influence of polystyrene on the mortars' properties was evaluated by the consistency index, water retention, water absorption, porosity, elasticity modulus, compressive strength, flexural strength, bond tensile strength and microscopy. The increase in the sulfonated polystyrene content decreased the elasticity modulus of the mortar and, despite higher porosity, there was a reduction of water absorption by capillarity. In relation to mortar without admixture, the modified mortar showed an increase in water retention and consistency index, and a large increase in flexural strength and bond tensile strength. The significant increase of bond tensile strength (214% with admixture 1% highlights the potential of the produced material as an adhesive mortar.

  5. Liquid alternative diesel fuels with high hydrogen content

    Energy Technology Data Exchange (ETDEWEB)

    Hancsok, Jenoe; Varga, Zoltan; Eller, Zoltan; Poelczmann, Gyoergy [Pannonia Univ., Veszprem (Hungary). MOL Dept. of Hydrocarbon Processing; Kasza, Tamas [MOL Hungarian Oil and Gas Plc., Szazhalombatta (Hungary)

    2013-06-01

    Mobility is a keystone of the sustainable development. In the operation of the vehicles as the tools of mobility internal combustion engines, so thus Diesel engines will play a remarkable role in the next decades. Beside fossil fuels - used for power these engines - liquid alternative fuels have higher and higher importance, because of their known advantages. During the presentation the categorization possibilities based on the chronology of their development and application will be presented. The importance of fuels with high hydrogen content will be reviewed. Research and development activity in the field of such kind of fuels will be presented. During this developed catalytic systems and main performance properties of the product will be presented which were obtained in case of biogasoils produced by special hydrocracking of natural triglycerides and in case of necessity followed by isomerization; furthermore in case of synthetic biogasoils obtained by the isomerization hydrocracking of Fischer-Tropsch paraffins produced from biomass based synthesis gas. Excellent combustion properties (cetane number > 65-75), good cold flow properties and reduced harmful material emission due to the high hydrogen content (C{sub n}H{sub 2n+2}) are highlighted. Finally production possibilities of linear and branched paraffins based on lignocelluloses are briefly reviewed. Summarizing it was concluded that liquid hydrocarbons with high isoparaffin content are the most suitable fuels regarding availability, economical and environmental aspects, namely the sustainable development. (orig.)

  6. Changes in Hydrogen Content During Steelmaking

    OpenAIRE

    Vrbek K.; Lamut J.; Marolt M.; Knap M.

    2015-01-01

    Štore Steel produces steel grades for spring, forging and engineering industry applications. Steelmaking technology consists of scrap melting in Electric Arc Furnace (EAF), secondary metallurgy in Ladle Furnace (LF) and continuous casting of billets (CC). Hydrogen content during steelmaking of various steel grades and steelmaking technologies was measured. Samples of steel melt from EAF, LF and CC were collected and investigated. Sampling from Electric Arc Furnace and Ladle Furnace was carrie...

  7. The radionuclide content of radioactive wastes

    International Nuclear Information System (INIS)

    1988-06-01

    This report presents the radionuclide content of stocks and arisings of radioactive wastes in the United Kingdom. Operational and decommissioning wastes are considered for both committed and prospective plant. Arisings are from power reactors, commercial reprocessing, fuel manufacture, medical and industrial sources and research and development. Data is included from Amersham International, British Nuclear Fuels, Central Electricity Generating Board, South of Scotland Electricity Board, United Kingdom Atomic Energy Authority and minor waste producers. (author)

  8. Combinations of mutant FAD2 and FAD3 genes to produce high oleic acid and low linolenic acid soybean oil.

    Science.gov (United States)

    Pham, Anh-Tung; Shannon, J Grover; Bilyeu, Kristin D

    2012-08-01

    High oleic acid soybeans were produced by combining mutant FAD2-1A and FAD2-1B genes. Despite having a high oleic acid content, the linolenic acid content of these soybeans was in the range of 4-6 %, which may be high enough to cause oxidative instability of the oil. Therefore, a study was conducted to incorporate one or two mutant FAD3 genes into the high oleic acid background to further reduce the linolenic acid content. As a result, soybean lines with high oleic acid and low linolenic acid (HOLL) content were produced using different sources of mutant FAD2-1A genes. While oleic acid content of these HOLL lines was stable across two testing environments, the reduction of linolenic acid content varied depending on the number of mutant FAD3 genes combined with mutant FAD2-1 genes, on the severity of mutation in the FAD2-1A gene, and on the testing environment. Combination of two mutant FAD2-1 genes and one mutant FAD3 gene resulted in less than 2 % linolenic acid content in Portageville, Missouri (MO) while four mutant genes were needed to achieve the same linolenic acid in Columbia, MO. This study generated non-transgenic soybeans with the highest oleic acid content and lowest linolenic acid content reported to date, offering a unique alternative to produce a fatty acid profile similar to olive oil.

  9. Comparison of chemical, rheological and sensory properties of kefir produced by kefir grains and commercial kefir starter

    Directory of Open Access Journals (Sweden)

    Irena Barukčić

    2017-01-01

    Full Text Available The main objective of this study was to compare chemical, rheological and sensory characteristics of kefir produced by using kefir grains and kefir starter. The intent was also to investigate whether it is plausible to use a combined inoculum (kefir grains and starter in order to obtain a kefir with improved characteristics in terms of sensory and rheological characteristics. Kefir samples were produced at 25 °C and 35 °C by using starter culture XPL-1, kefir grains and their combinations. All of the produced kefir samples were analysed for acidity, total dry matter, ethanol content, syneresis, viscosity and were sensory evaluated by a specially trained panel. There were no significant differences considering the total dry matter, syneresis, ethanol content and acidity. Excess viscosity was observed in samples produced by starter culture at 35 °C, which was described as untypical, yoghurt like and unsatisfactory by a sensory panel. The sample produced at 25 °C by equal amounts of kefir grains and starter culture received the highest scores at sensory evaluation and showed the best potential for optimizing the further use. Further investigations need to focus on examining kefir properties during the storage period, especially regarding microbiological and sensory properties, ethanol content and texture profile.

  10. The political economy of local content in African extractives

    DEFF Research Database (Denmark)

    Buur, Lars; Hansen, Michael; Kjær, Mette

    Extractive foreign direct investment (FDI) is heralded as the new development opportunity in Africa. But extractive FDI has a record of producing enclaves in host countries with few linkages to the local economy. Only if it creates local content will extractive FDI become a catalyst of development...

  11. Integrative approach to produce hydrogen and polyhydroxybutyrate from biowaste using defined bacterial cultures.

    Science.gov (United States)

    Patel, Sanjay K S; Kumar, Prasun; Singh, Mamtesh; Lee, Jung-Kul; Kalia, Vipin C

    2015-01-01

    Biological production of hydrogen (H2) and polyhydroxybutyrate (PHB) from pea-shell slurry (PSS) was investigated using defined mixed culture (MMC4, composed of Enterobacter, Proteus, Bacillus spp.). Under batch culture, 19.0LH2/kg of PSS (total solid, TS, 2%w/v) was evolved. Using effluent from the H2 producing stage, Bacillus cereus EGU43 could produce 12.4% (w/w) PHB. Dilutions of PSS hydrolysate containing glucose (0.5%, w/v) resulted in 45-75LH2/kg TS fed and 19.1% (w/w) of PHB content. Under continuous culture, MMC4 immobilized on coconut coir (CC) lead to an H2 yield of 54L/kg TS fed and a PHB content of 64.7% (w/w). An improvement of 2- and 3.7-fold in H2 and PHB yields were achieved in comparison to control. This integrative approach using defined set of bacterial strains can prove effective in producing biomolecules from biowastes. Copyright © 2014. Published by Elsevier Ltd.

  12. Using cotton plant residue to produce briquettes

    Energy Technology Data Exchange (ETDEWEB)

    Coates, W. [University of Arizona, Tucson, AZ (United States). Bioresources Research Facility

    2000-07-01

    In Arizona, cotton (Gossypium) plant residue left in the field following harvest must be buried to prevent it from serving as an overwintering site for insects such as the pink bollworm. Most tillage operations employed to incorporate the residue into the soil are energy intensive and often degrade soil structure. Trials showed that cotton plant residue could be incorporated with pecan shells to produce commercially acceptable briquettes. Pecan shell briquettes containing cotton residue rather than waste paper were slightly less durable, when made using equivalent weight mixtures and moisture contents. Proximate and ultimate analyses showed the only difference among briquette samples to be a higher ash content in those made using cotton plant residue. Briquettes made with paper demonstrated longer flame out time, and lower ash percentage, compared to those made with cotton plant residue. (author)

  13. Colour, phenolic content and antioxidant activity of grape juice

    Directory of Open Access Journals (Sweden)

    Vívian Maria Burin

    2010-12-01

    Full Text Available Viticultural practices in the State of Santa Catarina, Brazil, have shown economic growth, with the production of grapes used to produce wines and grape juice. Grapes are rich in phenolic compounds which have drawn attention not only because of their important role in the development of products derived from grapes, but also for their potential beneficial health effects. The objective of this study was to evaluate commercial, organic and homemade grape juices produced in Santa Catarina. Grape juices were analyzed for total phenolic content, colour, and antioxidant activity. The commercial juices had the highest average values for total monomeric anthocyanins and total phenolics. There was a strong positive correlation (R = 0.9566 between the antioxidant activity and total phenolic content for the commercial juice. In addition, the Principle Components Analysis showed a strong positive correlation between the red colour and total monomeric anthocyanins. However, the total monomeric anthocyanis and polymeric anthocyanins showed a negative correlation.

  14. Effects of replacement of binder content on bond strength of mortars

    Directory of Open Access Journals (Sweden)

    E. B. C. Costa

    Full Text Available The reduction of binder content in cementitious systems is an effective way to mitigate environmental impacts without increasing costs. The main purpose of this study is to evaluate the effect of content binder on bond strength of mortar-brick interface. For thus, it was studied mortars produced with two limestone fines with different particle size distribution. The limestone fines were added at rates of 0% to 60% at increments of 15% as partial volume replacement of binder. Mortars were prepared in proportion of 1:3 (binder + limestone: sand in volume. The water content was kept constant and equal to 18% in relation to total weight of solids. The mechanical property of mortars was evaluated by tensile strength and the performance of interface by bond strength tests at 14 days. Results indicate that is possible make mortars with 45% less than binder without reducing bond strength. Thus, the use of appropriate particles of limestone can produce more environmentally friendly concrete and rendering mortars by reducing its binder factor without affecting its performance.

  15. Procedure and apparatus for the determination of the gold content in a material containing gold

    International Nuclear Information System (INIS)

    1980-01-01

    This patent describes a method and apparatus for determining the gold content of materials, and in particular, of rock and stone samples. The procedure is based upon the irradiation of the material with neutrons and the determination of the intensity of the gamma radiation (279 keV) produced in the reaction 197 Au(n,n')sup(197m)Au. The neutron source used produces the neutrons by the deuteron-deuteron or deuteron-beryllium reaction. The energy of these neutrons is not high enough for producing fast neutron reactions in the other elements of the material. The apparatus described separates the samples with a gold content above a certain value by means of the procedure described above. (Th.P.)

  16. A rapid HPEAC method for determination of lactic acid produced by ...

    African Journals Online (AJOL)

    Poste

    water bath at 65°C from 3 to 4 min. The fat content (in percent) ... were compared to the EMBL, Gen Bank, DDJB and PDB databases, using BLAST ..... Structure of the exopolysaccharide produced by Lactococcus lactis subsp cremoris H414 ...

  17. Vegetation Water Content Mapping for Agricultural Regions in SMAPVEX16

    Science.gov (United States)

    White, W. A.; Cosh, M. H.; McKee, L.; Berg, A. A.; McNairn, H.; Hornbuckle, B. K.; Colliander, A.; Jackson, T. J.

    2017-12-01

    Vegetation water content impacts the ability of L-band radiometers to measure surface soil moisture. Therefore it is necessary to quantify the amount of water held in surface vegetation for an accurate soil moisture remote sensing retrieval. A methodology is presented for generating agricultural vegetation water content maps using Landsat 8 scenes for agricultural fields of Iowa and Manitoba for the Soil Moisture Active Passive Validation Experiments in 2016 (SMAPVEX16). Manitoba has a variety of row crops across the region, and the study period encompasses the time frame from emergence to reproduction, as well as a forested region. The Iowa study site is dominated by corn and soybeans, presenting an easier challenge. Ground collection of vegetation biomass and water content were also collected to provide a ground truth data source. Errors for the resulting vegetation water content maps ranged depending upon crop type, but generally were less than 15% of the total plant water content per crop type. Interpolation is done between Landsat overpasses to produce daily vegetation water content maps for the summer of 2016 at a 30 meter resolution.

  18. Potential of hot water extraction of birch wood to produce high-purity dissolving pulp after alkaline pulping.

    Science.gov (United States)

    Borrega, Marc; Tolonen, Lasse K; Bardot, Fanny; Testova, Lidia; Sixta, Herbert

    2013-05-01

    The potential of hot water extraction of birch wood to produce highly purified dissolving pulp in a subsequent soda-anthraquinone pulping process was evaluated. After intermediate extraction intensities, pulps with low xylan content (3-5%) and high cellulose yield were successfully produced. Increasing extraction intensity further decreased the xylan content in pulp. However, below a xylan content of 3%, the cellulose yield dramatically decreased. This is believed to be due to cleavage of glycosidic bonds in cellulose during severe hot water extractions, followed by peeling reactions during alkaline pulping. Addition of sodium borohydride as well as increased anthraquinone concentration in the pulping liquor increased the cellulose yield, but had no clear effects on pulp purity and viscosity. The low intrinsic viscosity of pulps produced after severe extraction intensities and soda-anthraquinone pulping corresponded to the viscosity at the leveling-off degree of polymerization, suggesting that nearly all amorphous cellulose had been degraded. Copyright © 2012 Elsevier Ltd. All rights reserved.

  19. Discussion on the genesis of uranium-producing pegmatite in Shangdan area

    Energy Technology Data Exchange (ETDEWEB)

    Mingyue, Feng [Beijing Research Inst. of Uranium Geology (China)

    1996-01-01

    This paper describes the characteristics of uranium-producing pematite, gneissic granodiorite metamorphic rocks of the Qinling Group in such aspects as petrochemical compositions, contents of trace elements (Rb and Sr etc.), initial ratio of strontium isotopes and assemblage types of accessory minerals. Through the comparison between U-barren pegmatite within the massif and U-producing pegmatite outside the massif, and the study on Sm and Nd isotope tracers, a viewpoint is presented that the U-producing pegmatite veins resulted from slow crystallization of granitic magma under relatively confined condition produced from the selective melting of the Qinling Group metamorphic rocks rather than residual magmatic crystallization from the late-stage magmatic differentiation of gneissic granodiorite (T{sub DM} is about 10 Ma).

  20. Natural Abundance 14C Content of Dibutyl Phthalate (DBP from Three Marine Algae

    Directory of Open Access Journals (Sweden)

    Kazuyo Ukai

    2006-11-01

    Full Text Available Abstract: Analysis of the natural abundance 14C content of dibutyl phthalate (DBP from two edible brown algae, Undaria pinnatifida and Laminaria japonica, and a green alga, Ulva sp., revealed that the DBP was naturally produced. The natural abundance 14C content of di-(2-ethylhexyl phthalate (DEHP obtained from the same algae was about 50-80% of the standard sample and the 14C content of the petrochemical (industrial products of DBP and DEHP were below the detection limit.

  1. CO2 Removal from Mars EMU, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — CO2 control for during ExtraVehicular Activity (EVA) on mars is challenging. Lithium hydroxide (LiOH) canisters have impractical logistics penalties, and regenerable...

  2. Effect of Carbon Content on the Properties of Iron-Based Powder Metallurgical Parts Produced by the Surface Rolling Process

    Directory of Open Access Journals (Sweden)

    Yan Zhao

    2018-01-01

    Full Text Available In recent years, the rolling densification process has become increasingly widely used to strengthen powder metallurgy parts. The original composition of the rolled powder metallurgy blank has a significant effect on the rolling densification technology. The present work investigated the effects of different carbon contents (0 wt. %, 0.2 wt. %, 0.45 wt. %, and 0.8 wt. % on the rolling densification. The selection of the raw materials in the surface rolling densification process was analyzed based on the pore condition, structure, hardness, and friction performance of the materials. The results show that the 0.8 wt. % carbon content of the surface rolling material can effectively improve the properties of iron-based powder metallurgy parts. The samples with 0.8 wt. % carbon have the highest surface hardness (340 HV0.1 and the lowest surface friction coefficient (0.35. Even if the dense layer depth is 1.13 mm, which is thinner than other samples with low carbon content, it also meets the requirements for powder metallurgy parts such as gears used in the auto industry.

  3. Analysis of deoxynivalenol and deoxynivalenol-3-glucosides content in Canadian spring wheat cultivars inoculated with Fusarium graminearum.

    Science.gov (United States)

    Amarasinghe, Chami C; Simsek, Senay; Brûlé-Babel, Anita; Fernando, W G Dilantha

    2016-07-01

    Contamination of wheat grains with Fusarium mycotoxins and their modified forms is an important issue in wheat industry. The objective of this study was to analyse the deoxynivalenol (DON) and deoxynivalenol-3-glucosides (D3G) content in Canadian spring wheat cultivars grown in two locations, inoculated with a mixture of 3-acetyldeoxynivalenol (3-ADON)-producing Fusarium graminearum strains and a mixture of 15-acetlyldeoxynivalenol (15-ADON)-producing F. graminearum strains. According to the analysis of variance, significant differences were observed among the cultivars for Fusarium head blight (FHB) disease index, Fusarium-damaged kernel percentage (%FDK), DON content and D3G content. When the effect of chemotype was considered, significant differences were observed for FHB disease index, FDK percentage and DON content. The D3G content and D3G/DON ratio were not significantly different between the chemotypes, except for D3G content at the Winnipeg location. The Pearson correlation coefficient between DON and D3G was 0.84 and 0.77 at Winnipeg and Carman respectively. The highest D3G/DON ratio was observed in cultivars Carberry (44%) in Carman and CDC Kernen (63.8%) in Winnipeg. The susceptible cultivars showed lower D3G/DON ratio compared with the cultivars rated as moderately resistant and intermediate. The current study indicated that Canadian spring cultivars produce D3G upon Fusarium infection.

  4. Operando X-ray diffraction analysis for a glyme-based Li-O{sub 2} battery

    Energy Technology Data Exchange (ETDEWEB)

    Yogi, C.; Takao, N.; Kubobuchi, K.; Matsumoto, M.; Mogi, M., E-mail: mogi@nissan-arc.co.jp; Imai, H. [Device-functional analysis department, NISSAN ARC Ltd., 1 Natsushima, Yokosuka Kanagawa, 237-0061 JAPAN (Japan); Watanabe, T. [Japan Synchrotron Radiation Research Institute (JASRI), 1-1-1 Koto, Sayo Hyogo, 679-5198 JAPAN (Japan)

    2016-08-26

    We investigated the effect of the carbon species in the air (oxygen) electrode, electrolyte concentration, and humidity in the supplied O{sub 2} gas on the Li-O{sub 2} reactions by using the operando XRD analysis. Regarding carbon species, we found that the over-potentials in the galvanostatic discharge-charge process were suppressed when using the KB carbon in the air electrode. The results of operando XRD measurements revealed that the Li{sub 2}O{sub 2} formed on the KB had the smaller crystalline or more amorphous like structures, which could be one reason for faster reaction kinetics of Li{sub 2}O{sub 2} dissolution. The discharge-charge curves of the cells with different concentration of LiTFSI/(G4){sub n} electrolyte showed the slight difference but less differences in the Li{sub 2}O{sub 2} formation and dissolution behaviors. In addition to the nature of Li{sub 2}O{sub 2} products, reaction of Li-salts would also have ineligible effects. We also found that the higher humidity in oxygen produced more the LiOH and promoted the Li{sub 2}O{sub 2} dissolution, which indicate that the LiOH formation could affect the Li{sub 2}O{sub 2} morphologies or surface chemistries. Our present results demonstrated that the operando XRD measurement are useful for analyzing the reaction mechanism of Li-O{sub 2} battery.

  5. Production of Manooligomannan from Palm Kernel Cake by Mannanase Produced from Streptomyces Cyaenus

    Directory of Open Access Journals (Sweden)

    Awan Purnawan

    2017-04-01

    Full Text Available The increase of public attention to health has prompted researchers to look for new sources of functional food. Palm Cake Kernel (PKC waste was abundant in Indonesia, Oligosaccharide has an important benefit for human health. Recently oligosaccharide is not only important as an artificial sweetener, but also as a functional food component. This study was aimed to produce oligo-mannan enzymatically from PKC waste using mannanase derived from of Streptomyces cyaenus isolates of indigenous Indonesia. The enzyme concentration was determined by enzyme activity assay while oligo-mannan content in the PKC was analyzed using TLC and HPLC. Mannanase enzyme activity of 1706 U/ml on the second day of agitation 200 rpm at a temperature of 30°C Hydrolysis of mannooligomannan by using mannanase produced by streptomyces cyaenus. The optimum mannanase enzyme activity obtained on day 2 with the value of the activity as much of 0.702 U/mL. The protein content of the 2nd day at an agitation speed of 150 rpm, 200 rpm, and 250 rpm, respectively, were 1783, 1950 and 2283 ppm. Streptomyces cyaenus is Indonesian original isolates potentially producing mannanase that can produce mannooligomannan.

  6. The bio refinery; producing feed and fuel from grain.

    Science.gov (United States)

    Scholey, D V; Burton, E J; Williams, P E V

    2016-04-15

    It is both possible and practicable to produce feed and fuel from grain. Using the value of grain to produce renewable energy for transport, while using the remaining protein content of the grain as a valuable protein source for livestock and for fish, can be seen as a complimentary and optimal use of all the grain constituents. Consideration must be given to maximise the value of the yeast components, as substantial yeast is generated during the fermentation of the grain starch to produce ethanol. Yeast is a nutritionally rich feed ingredient, with potential for use both as feed protein and as a feed supplement with possible immunity and gut health enhancing properties. Bioprocessing, with the consequent economies of scale, is a process whereby the value of grain can be optimised in a way that is traditional, natural and sustainable for primarily producing protein and oil for feed with a co-product ethanol as a renewable fuel. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Content

    DEFF Research Database (Denmark)

    Keiding, Tina Bering

    secondary levels. In subject matter didactics, the question of content is more developed, but it is still mostly confined to teaching on lower levels. As for higher education didactics, discussions on selection of content are almost non-existent on the programmatic level. Nevertheless, teachers are forced...... curriculum, in higher education, and to generate analytical categories and criteria for selection of content, which can be used for systematic didactical reflection. The larger project also concerns reflection on and clarification of the concept of content, including the relation between content at the level......Aim, content and methods are fundamental categories of both theoretical and practical general didactics. A quick glance in recent pedagogical literature on higher education, however, reveals a strong preoccupation with methods, i.e. how teaching should be organized socially (Biggs & Tang, 2007...

  8. A novel method of producing a microcrystalline beta-sitosterol suspension in oil

    DEFF Research Database (Denmark)

    Christiansen, Leena I; Rantanen, Jukka T; von Bonsdorff, Anna K

    2002-01-01

    This paper describes a novel method of producing a microcrystalline oral suspension containing beta-sitosterol in oil for the treatment of hypercholesterolaemia. beta-Sitosterol pseudopolymorphs with different water contents were crystallized from acetone and acetone-water solutions. Structural...

  9. Manipulation of carbon flux into fatty acid biosynthesis pathway in Dunaliella salina using AccD and ME genes to enhance lipid content and to improve produced biodiesel quality

    Directory of Open Access Journals (Sweden)

    Ahmad Farhad Talebi

    2014-08-01

    Full Text Available Advanced generations of biofuels basically revolve around non-agricultural energy crops. Among those, microalgae owing to its unique characteristics i.e. natural tolerance to waste and saline water, sustainable biomass production and high lipid content (LC, is regarded by many as the ultimate choice for the production of various biofuels such as biodiesel. In the present study, manipulation of carbon flux into fatty acid biosynthesis pathway in Dunaliella salina was achieved using pGH plasmid harboring AccD and ME genes to enhance lipid content and to improve produced biodiesel quality. The stability of transformation was confirmed by PCR after several passages. Southern hybridization of AccD probe with genomic DNA revealed stable integration of the cassette in the specific positions in the chloroplast genome with no read through transcription by indigenous promoters. Comparison of the LC and fatty acid profile of the transformed algal cell line and the control revealed the over-expression of the ME/AccD genes in the transformants leading to 12% increase in total LC and significant improvements in biodiesel properties especially by increasing algal oil oxidation stability. The whole process successfully implemented herein for transforming algal cells by genes involved in lipid production pathway could be helpful for large scale biodiesel production from microalgae.

  10. A Comparative Analysis of Numbers and Biology Content Domains between Turkey and the USA

    Science.gov (United States)

    Incikabi, Lutfi; Ozgelen, Sinan; Tjoe, Hartono

    2012-01-01

    This study aimed to compare Mathematics and Science programs focusing on TIMSS content domains of Numbers and Biology that produced the largest achievement gap among students from Turkey and the USA. Specifically, it utilized the content analysis method within Turkish and New York State (NYS) frameworks. The procedures of study included matching…

  11. Organ donation on Web 2.0: content and audience analysis of organ donation videos on YouTube.

    Science.gov (United States)

    Tian, Yan

    2010-04-01

    This study examines the content of and audience response to organ donation videos on YouTube, a Web 2.0 platform, with framing theory. Positive frames were identified in both video content and audience comments. Analysis revealed a reciprocity relationship between media frames and audience frames. Videos covered content categories such as kidney, liver, organ donation registration process, and youth. Videos were favorably rated. No significant differences were found between videos produced by organizations and individuals in the United States and those produced in other countries. The findings provide insight into how new communication technologies are shaping health communication in ways that differ from traditional media. The implications of Web 2.0, characterized by user-generated content and interactivity, for health communication and health campaign practice are discussed.

  12. Growth of locally isolated microalga in POME to produce lipid as alternative energy sources

    Science.gov (United States)

    Elvitriana; Munir, E.; Delvian; Wahyuningsih, H.

    2018-04-01

    Purpose of this study was to find the best growth of locally isolated microalgae that produce lipids from Palm Oil Mill Effluent (POME) as an alternative energy source. Microalgae was cultivated in POME in glass vessel at room temperature using a lighting intensity of 13,000 lux and continuously aeration for 24 and 12 hours, respectively. Biomass of microalgae were analyzed daily to get their growth by spectrophotometry at 624 nm wavelength, whereas Modified Bligh and Dyer method determined lipid content. Results show that the best growth occurred at 10% inoculum with lighting cycle and aeration of 24 hours (on/off) and resulting highest biomass content of 0.99 g dry weight/L followed by the decrease of organic substances in POME. The percentage reduction of COD, BOD, TSS, and oil at POME reached above 92%, while phosphate concentration reached 89.2%. Cultivation of microalgae in POME for 12 days showed its ability to reduce organic substances and nutrients in POME and produced biomass with lipid content of 35%. These results reached to the conclusion that locally isolated microalgae has an ability to treat POME safely for environment and POME can be used as a growing medium of microalgae that produces lipids.

  13. Provision of information to consumers about the calorie content of alcoholic drinks: did the Responsibility Deal pledge by alcohol retailers and producers increase the availability of calorie information?

    Science.gov (United States)

    Petticrew, M; Douglas, N; Knai, C; Maani Hessari, N; Durand, M A; Eastmure, E; Mays, N

    2017-08-01

    Alcohol is a significant source of dietary calories and is a contributor to obesity. Industry pledges to provide calorie information to consumers have been cited as reasons for not introducing mandatory ingredient labelling. As part of the Public Health Responsibility Deal (RD) in England, alcohol retailers and producers committed to providing consumers with information on the calorie content of alcoholic drinks. This study examines what was achieved following this commitment and considers the implications for current industry commitments to provide information on alcohol calories. Analysis of RD pledge delivery plans and progress reports. Assessment of calorie information in supermarkets and in online stores. (i) Analysis of the content of pledge delivery plans and annual progress reports of RD signatories to determine what action they had committed to, and had taken, to provide calorie information. (ii) Analysis of the availability of calorie information on product labels; in UK supermarkets; and on online shopping sites and websites. No information was provided in any of 55 stores chosen to represent all the main UK supermarkets. Calorie information was not routinely provided on supermarkets' websites, or on product labels. One of the stated purposes of the RD was to provide consumers with the information to make informed health-related choices, including providing information on the calorie content of alcoholic drinks. This study indicates that this did not take place to any significant extent. The voluntary implementation of alcohol calorie labelling by industry needs to continue to be carefully monitored to determine whether and how it is done. Copyright © 2017 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

  14. Production and characterization of thin 7Li targets fabricated by ion implantation

    International Nuclear Information System (INIS)

    Cruz, J.; Fonseca, M.; Luis, H.; Mateus, R.; Marques, H.; Jesus, A.P.; Ribeiro, J.P.; Teodoro, O.M.N.D.; Rolfs, C.

    2009-01-01

    Very high fluence implantation of 7 Li + ions was used to promote the formation of a thin and high density 7 Li target in the surface region of Al samples. The implanted volume was characterized by particle induced gamma-ray emission, Rutherford backscattering spectrometry, X-ray photoelectron spectroscopy and nuclear reaction analysis, revealing that the implanted surface is a combination of Li 2 CO 3 , metallic lithium, LiOH and C, with almost no Al present. Radiation damage effects by proton beams were studied by observing the evolution of the 7 Li(p, α) 4 He nuclear reaction yield with the accumulated charge, at different proton energies, revealing high stability of the produced Li target.

  15. Effect of 60Co γ-ray irradiation to Agaricus blazei on the amino acid content of their fruitbodies

    International Nuclear Information System (INIS)

    Jiang Zhihe; Lin Yong; Xiao Shuxia

    2004-01-01

    The amino acid contents of Agaricus blazei fruitbodies produced from strains irradiated with different dosages of 60 Co γ-ray were determined. The results showed that the contents of essential amino acids, essential amino acids for children, methionine amino acids, side chain amino acids, tasty amino acids, sweet amino acids and aromatic amino acids of Agaricus blazei fruitbodies produced from irradiated atrains were all higher than that from the CK

  16. Natural Variation in Synthesis and Catabolism Genes Influences Dhurrin Content in Sorghum

    Directory of Open Access Journals (Sweden)

    Chad M. Hayes

    2015-07-01

    Full Text Available Cyanogenic glucosides are natural compounds found in more than 1000 species of angiosperms that produce HCN and are deemed undesirable for agricultural use. However, these compounds are important components of the primary defensive mechanisms of many plant species. One of the best-studied cyanogenic glucosides is dhurrin [(--hydroxymandelonitrile-β--glucopyranoside], which is produced primarily in sorghum [ (L. Moench]. The biochemical basis for dhurrin metabolism is well established; however, little information is available on its genetic control. Here, we dissect the genetic control of leaf dhurrin content through a genome-wide association study (GWAS using a panel of 700 diverse converted sorghum lines (conversion panel previously subjected to pre-breeding and selected for short stature (∼1 m in height and photoperiod insensitivity. The conversion panel was grown for 2 yr in three environments. Wide variation for leaf dhurrin content was found in the sorghum conversion panel, with the Caudatum group exhibiting the highest dhurrin content and the Guinea group showing the lowest dhurrin content. A GWAS using a mixed linear model revealed significant associations (a false discovery rate [FDR] < 0.05 close to both UGT 185B1 in the canonical biosynthetic gene cluster on chromosome 1 and close to the catabolic dhurrinase loci on chromosome 8. Dhurrin content was associated consistently with biosynthetic genes in the two N-fertilized environments, while dhurrin content was associated with catabolic loci in the environment without supplemental N. These results suggest that genes for both biosynthesis and catabolism are important in determining natural variation for leaf dhurrin in sorghum in different environments.

  17. Toward a Strategic Management Perspective on Local Content in African Extractives

    DEFF Research Database (Denmark)

    Hansen, Michael W.

    understanding of MNC strategy and interests. Hence, the aim of this paper is to characterize and conceptually develop the strategic management perspective on local content. The paper outlines generic strategies that MNCs may adopt to balance the often conflicting pressures for local content and global......Local content requirements - i.e. government backed requirements that extractive MNCs must procure inputs locally - are fast becoming a major issue in MNC-host country bargaining in Africa. Across Africa, governments are seeking to mobilize MNCs for sustainable development through increasingly......, this literature is predominantly informed by economic and political perspectives, and strategic management perspectives are virtually absent. This is problematic as one of the main reasons why local content interventions in Africa fail to produce the expected results is that they often are based on an inadequate...

  18. Seed oil content and fatty acid composition of annual halophyte ...

    African Journals Online (AJOL)

    Suaeda acuminata produces two morphologically distinct types of seeds on the same plant. This study was conducted to compare oil content and fatty acid composition of the two seed morphs. Though oil characteristics between dimorphic seeds showed statistically significant difference, these differences were relatively ...

  19. Phase-image-based content-addressable holographic data storage

    Science.gov (United States)

    John, Renu; Joseph, Joby; Singh, Kehar

    2004-03-01

    We propose and demonstrate the use of phase images for content-addressable holographic data storage. Use of binary phase-based data pages with 0 and π phase changes, produces uniform spectral distribution at the Fourier plane. The absence of strong DC component at the Fourier plane and more intensity of higher order spatial frequencies facilitate better recording of higher spatial frequencies, and improves the discrimination capability of the content-addressable memory. This improves the results of the associative recall in a holographic memory system, and can give low number of false hits even for small search arguments. The phase-modulated pixels also provide an opportunity of subtraction among data pixels leading to better discrimination between similar data pages.

  20. Commercial and Advertising Content in Free Consumer Curriculum Materials.

    Science.gov (United States)

    Rudd, Joel

    The results of the first systematic content analysis of free consumer curriculum materials indicate the extent to which such business sponsored materials are an advertising vehicle for their producers. The business sponsored materials in this sample of 116 items contain nearly twice as many advertising statements as the non-business materials.…

  1. Effect of Moisture Content on Lignocellulosic Power Generation: Energy, Economic and Environmental Impacts

    Directory of Open Access Journals (Sweden)

    Karthik Rajendran

    2017-12-01

    Full Text Available The moisture content of biomass affects its processing for applications such as electricity or steam. In this study, the effects of variation in moisture content of banagrass and energycane was evaluated using techno-economic analysis and life-cycle assessments. A 25% loss of moisture was assumed as a variation that was achieved by field drying the biomass. Techno-economic analysis revealed that high moisture in the biomass was not economically feasible. Comparing banagrass with energycane, the latter was more economically feasible; thanks to the low moisture and ash content in energycane. About 32 GWh/year of electricity was produced by field drying 60,000 dry MT/year energycane. The investment for different scenarios ranged between $17 million and $22 million. Field-dried energycane was the only economically viable option that recovered the investment after 11 years of operation. This scenario was also more environmentally friendly, releasing 16-gCO2 equivalent/MJ of electricity produced.

  2. Weld metal microstructures of hardfacing deposits produced by self-shielded flux-cored arc welding

    International Nuclear Information System (INIS)

    Dumovic, M.; Monaghan, B.J.; Li, H.; Norrish, J.; Dunne, D.P.

    2015-01-01

    The molten pool weld produced during self-shielded flux-cored arc welding (SSFCAW) is protected from gas porosity arising from oxygen and nitrogen by reaction ('killing') of these gases by aluminium. However, residual Al can result in mixed micro-structures of δ-ferrite, martensite and bainite in hardfacing weld metals produced by SSFCAW and therefore, microstructural control can be an issue for hardfacing weld repair. The effect of the residual Al content on weld metal micro-structure has been examined using thermodynamic modeling and dilatometric analysis. It is concluded that the typical Al content of about 1 wt% promotes δ-ferrite formation at the expense of austenite and its martensitic/bainitic product phase(s), thereby compromising the wear resistance of the hardfacing deposit. This paper also demonstrates how the development of a Schaeffler-type diagram for predicting the weld metal micro-structure can provide guidance on weld filler metal design to produce the optimum microstructure for industrial hardfacing applications.

  3. How Do Grass Species, Season and Ensiling Influence Mycotoxin Content in Forage?

    Directory of Open Access Journals (Sweden)

    Adam Nawrath

    2013-11-01

    Full Text Available Mycotoxins are secondary metabolites produced by fungal species that have harmful effects on mammals. The aim of this study was to assess the content of mycotoxins in fresh-cut material of selected forage grass species both during and at the end of the growing season. We further assessed mycotoxin content in subsequently produced first-cutting silages with respect to the species used in this study: Lolium perenne (cv. Kentaur, Festulolium pabulare (cv. Felina, Festulolium braunii (cv. Perseus, and mixtures of these species with Festuca rubra (cv. Gondolin or Poa pratensis (Slezanka. The mycotoxins deoxynivalenol, zearalenone and T-2 toxin were mainly detected in the fresh-cut grass material, while fumonisin and aflatoxin contents were below the detection limits. July and October were the most risky periods for mycotoxins to occur. During the cold temperatures in November and December, the occurrence of mycotoxins in fresh-cut material declined. Although June was a period with low incidence of mycotoxins in green silage, contents of deoxynivalenol and zearalenone in silages from the first cutting exceeded by several times those determined in their biomass collected directly from the field. Moreover, we observed that use of preservatives or inoculants did not prevent mycotoxin production.

  4. Roller compaction: Effect of morphology and amorphous content of lactose powder on product quality.

    Science.gov (United States)

    Omar, Chalak S; Dhenge, Ranjit M; Osborne, James D; Althaus, Tim O; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

    2015-12-30

    The effect of morphology and amorphous content, of three types of lactose, on the properties of ribbon produced using roller compaction was investigated. The three types of lactose powders were; anhydrous SuperTab21AN, α-lactose monohydrate 200 M, and spray dried lactose SuperTab11SD. The morphology of the primary particles was identified using scanning electron microscopy (SEM) and the powder amorphous content was quantified using NIR technique. SEM images showed that 21AN and SD are agglomerated type of lactose whereas the 200 M is a non-agglomerated type. During ribbon production, an online thermal imaging technique was used to monitor the surface temperature of the ribbon. It was found that the morphology and the amorphous content of lactose powders have significant effects on the roller compaction behaviour and on ribbon properties. The agglomerated types of lactose produced ribbon with higher surface temperature and tensile strength, larger fragment size, lower porosity and lesser fines percentages than the non-agglomerated type of lactose. The lactose powder with the highest amorphous content showed to result in a better binding ability between the primary particles. This type of lactose produced ribbons with the highest temperature and tensile strength, and the lowest porosity and amount of fines in the product. It also produced ribbon with more smooth surfaces in comparison to the other two types of lactose. It was noticed that there is a relationship between the surface temperature of the ribbon during production and the tensile strength of the ribbon; the higher the temperature of the ribbon during production the higher the tensile strength of the ribbon. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. TREATMENT OF PRODUCED OIL AND GAS WATERS WITH SURFACTANT-MODIFIED ZEOLITE

    Energy Technology Data Exchange (ETDEWEB)

    Lynn E. Katz; R.S. Bowman; E.J. Sullivan

    2003-11-01

    Co-produced water from the oil and gas industry accounts for a significant waste stream in the United States. It is by some estimates the largest single waste stream in the country, aside from nonhazardous industrial wastes. Characteristics of produced water include high total dissolved solids content, dissolved organic constituents such as benzene and toluene, an oil and grease component, and chemicals added during the oil-production process. While most of the produced water is disposed via reinjection, some must be treated to remove organic constituents before the water is discharged. Current treatment options are successful in reducing the organic content; however, they cannot always meet the levels of current or proposed regulations for discharged water. Therefore, an efficient, cost-effective treatment technology is needed. Surfactant-modified zeolite (SMZ) has been used successfully to treat contaminated ground water for organic and inorganic constituents. In addition, the low cost of natural zeolites makes their use attractive in water-treatment applications. This report summarizes the work and results of this four-year project. We tested the effectiveness of surfactant-modified zeolite (SMZ) for removal of BTEX with batch and column experiments using waters with BTEX concentrations that are comparable to those of produced waters. The data from our experimental investigations showed that BTEX sorption to SMZ can be described by a linear isotherm model, and competitive effects between compounds were not significant. The SMZ can be readily regenerated using air stripping. We field-tested a prototype SMZ-based water treatment system at produced water treatment facilities and found that the SMZ successfully removes BTEX from produced waters as predicted by laboratory studies. When compared to other existing treatment technologies, the cost of the SMZ system is very competitive. Furthermore, the SMZ system is relatively compact, does not require the storage of

  6. Kynurenic acid content in anti-rheumatic herbs.

    Science.gov (United States)

    Zgrajka, Wojciech; Turska, Monika; Rajtar, Grażyna; Majdan, Maria; Parada-Turska, Jolanta

    2013-01-01

    The use of herbal medicines is common among people living in rural areas and increasingly popular in urbanized countries. Kynurenic acid (KYNA) is a metabolite of kynurenine possessing anti-inflammatory, anti-oxidative and pain reliving properties. Previous data indicated that the content of KYNA in the synovial fluid of patients with rheumatoid arthritis is lower than in patients with osteoarthritis. Rheumatoid arthritis is a chronic, systemic inflammatory disorder affecting about 1% of the world's population. The aim of the presented study was to investigate the content of KYNA in 11 herbal preparations used in rheumatic diseases. The following herbs were studied: bean pericarp, birch leaf, dandelion root, elder flower, horsetail herb, nettle leaf, peppermint leaf and willow bark. An anti-rheumatic mixture of the herbs Reumatefix and Reumaflos tea were also investigated. The herbs were prepared according to producers' directions. In addition, the herbal supplement Devil's Claw containing root of Harpagophytum was used. KYNA content was measured using the high-performance liquid chromatography method, and KYNA was detected fluorometrically. KYNA was found in all studied herbal preparations. The highest content of KYNA was found in peppermint, nettle, birch leaf and the horsetail herb. The lowest content of KYNA was found in willow bark, dandelion root and in the extract from the root of Harpagophytum. These findings indicate that the use of herbal preparations containing a high level of KYNA can be considered as a supplementary measure in rheumatoid arthritis therapy, as well as in rheumatic diseases prevention.

  7. Influence of some viticultural practices on the polyphenolic content of wines produced from cv. Agiorgitiko (Vitis vinifera L.

    Directory of Open Access Journals (Sweden)

    Sofoklis Petropoulos

    2011-12-01

    Significance and impact of the study: Climate and weather conditions should be taken into account before applying practices that increase bunch exposure, especially in warm wine regions where light could be detrimental to the polyphenolic content of the wines.

  8. Multimedia content classification metrics for content adaptation

    OpenAIRE

    Fernandes, Rui; Andrade, M.T.

    2015-01-01

    Multimedia content consumption is very popular nowadays. However, not every content can be consumed in its original format: the combination of content, transport and access networks, consumption device and usage environment characteristics may all pose restrictions to that purpose. One way to provide the best possible quality to the user is to adapt the content according to these restrictions as well as user preferences. This adaptation stage can be best executed if knowledge about the conten...

  9. Multimedia content classification metrics for content adaptation

    OpenAIRE

    Fernandes, Rui; Andrade, M.T.

    2016-01-01

    Multimedia content consumption is very popular nowadays. However, not every content can be consumed in its original format: the combination of content, transport and access networks, consumption device and usage environment characteristics may all pose restrictions to that purpose. One way to provide the best possible quality to the user is to adapt the content according to these restrictions as well as user preferences. This adaptation stage can be best executed if knowledge about the conten...

  10. Refining Bio-Gas Produced from Biomass: An Alternative to Cooking Gas

    Directory of Open Access Journals (Sweden)

    A. S. ABDULKAREEM

    2005-06-01

    Full Text Available Our life is completely dependent on a reliable and adequate supply of energy. In other to reduce dependence on fossil fuels, the use of animal dung in producing a renewable alternative source of energy has been proved using cow dung. This work is aimed at produced and refined bio - gas from animal dung by reduces the H2S and CO2 content of bio - gas in other to improved the quality of the bio - gas to be used as an alternative to the petroleum based produces in use now. The sample of gas produced was passed through the gas chromatography to determine the percentage composition (mol % dry basis of the bio - gas contents. The results of the bio - gas before refinement were 54.09% mole dry CH4, 40.02mole % dry CO2 and 0.80mole % dry H2S which conformed with the literature values of 50 - 65 % mole dry CH4, 35 - 50 % mole dry CO2 and 0.1 - 1.0 % mole dry H2S. After refining, the composition of bio - gas on dry basis were 54.09% mole dry CH4, 4.01% mole dry CO2, 0.02% mole dry O2, 0.05% mole dry NH3, 0.01% mole dry H2S, 0.5% mole dry H2 and 2.54% mole dry N2. Analysis of the remnant indicated that it could be used for plant nutrient.

  11. Measuring ash content of coal

    International Nuclear Information System (INIS)

    Clayton, C.G.; Wormald, M.R.

    1980-01-01

    An apparatus for measuring the ash content of coal is claimed. It comprises a means for irradiating a known quantity of coal in a transport container with a known dose of neutrons, a means for detecting γ-rays having a predetermined energy emitted by the irradiated coal, the γ-rays being indicative of the presence of an ash-forming element in the coal, a means for producing a signal related to the intensity of the γ-ray emission and a means responsive to the signal to provide an indication of the concentration of the ash-forming element in the coal

  12. Development of a Solid-State Fermentation System for Producing Bioethanol from Food Waste

    Science.gov (United States)

    Honda, Hiroaki; Ohnishi, Akihiro; Fujimoto, Naoshi; Suzuki, Masaharu

    Liquid fermentation is the a conventional method of producing bioethanol. However, this method results in the formation of high concentrations waste after distillation and futher treatment requires more energy and is costly(large amounts of costly energy).Saccharification of dried raw garbage was tested for 12 types of Koji starters under the following optimum culture conditions: temperature of 30°C and initial moisture content of 50%.Among all the types, Aspergillus oryzae KBN650 had the highest saccharifying power. The ethanol-producing ability of the raw garbage was investigated for 72 strains of yeast, of which Saccharomyces cerevisiae A30 had the highest ethanol production(yield)under the following optimum conditions: 1 :1 ratio of dried garbage and saccharified garbage by weight, and initial moisture content of 60%. Thus, the solid-state fermentation system consisted of the following 4 processes: moisture control, saccharification, ethanol production and distillation. This system produced 0.6kg of ethanol from 9.6kg of garbage. Moreover the ethanol yield from all sugars was calculated to be 0.37.

  13. Digital processing of ionospheric electron content data

    Science.gov (United States)

    Bernhardt, P. A.

    1979-01-01

    Ionospheric electron content data contain periodicities that are produced by a diversity of sources including hydromagnetic waves, gravity waves, and lunar tides. Often these periodicities are masked by the strong daily variation in the data. Digital filtering can be used to isolate the weaker components. The filtered data can then be further processed to provide estimates of the source properties. In addition, homomorphic filtering may be used to identify nonlinear interactions in the ionosphere.

  14. Fast crawling methods of exploring content distributed over large graphs

    KAUST Repository

    Wang, Pinghui

    2018-03-15

    Despite recent effort to estimate topology characteristics of large graphs (e.g., online social networks and peer-to-peer networks), little attention has been given to develop a formal crawling methodology to characterize the vast amount of content distributed over these networks. Due to the large-scale nature of these networks and a limited query rate imposed by network service providers, exhaustively crawling and enumerating content maintained by each vertex is computationally prohibitive. In this paper, we show how one can obtain content properties by crawling only a small fraction of vertices and collecting their content. We first show that when sampling is naively applied, this can produce a huge bias in content statistics (i.e., average number of content replicas). To remove this bias, one may use maximum likelihood estimation to estimate content characteristics. However, our experimental results show that this straightforward method requires to sample most vertices to obtain accurate estimates. To address this challenge, we propose two efficient estimators: special copy estimator (SCE) and weighted copy estimator (WCE) to estimate content characteristics using available information in sampled content. SCE uses the special content copy indicator to compute the estimate, while WCE derives the estimate based on meta-information in sampled vertices. We conduct experiments on a variety of real-word and synthetic datasets, and the results show that WCE and SCE are cost effective and also “asymptotically unbiased”. Our methodology provides a new tool for researchers to efficiently query content distributed in large-scale networks.

  15. Flourine content of plants and animals

    Energy Technology Data Exchange (ETDEWEB)

    Tsunoda, F; Kunita, H

    1973-06-01

    The fluoride content in the air can be measured by plant indicators, either by the extent of plant damage or by the cumulative fluoride content in the plant. The latter seems to be more effective when dealing with fluorine in the air, since a considerable amount of F accumulation in the plant sometimes does not manifest itself in damage. Leaves of gladioli are often used as indicators, but experiments have shown that the leaves of wild iris and flags are just as susceptible to F in the air. The pine and cedar needles and tulip and orange leaves are also sensitive indicators. The measurements of soluble fluorine in the air were taken for the past 5 years by the lime treated filter paper method and a dust meter in seven polluted areas, and the cumulative F content in the leaves of iris in these areas were compared with iris leaves in control areas. By the characteristic translocation of F, the tips and edges of leaves had much higher F content than other parts of the same plant. Approximately 1/3 of the measurements in those parts could be considered as a pollution index. The leaves taken from the most polluted areas showed approximately 80 times over the leaves from control areas in dry weight. Even 1/3 of the actual measurements was 100 ppm in dry weight, 30 ppm in raw weight. The produce in air polluted areas has 5-10 ppm F content in polished rice and green vegetables. If the daily consumption of rice is 308 g/capita, 3.08 mg of F is taken daily into the human body.

  16. Effect of Manganese Content on the Fabrication of Porous Anodic Alumina

    Directory of Open Access Journals (Sweden)

    C. H. Voon

    2012-01-01

    Full Text Available The influence of manganese content on the formation of well-ordered porous anodic alumina was studied. Porous anodic alumina has been produced on aluminium substrate of different manganese content by single-step anodizing at 50 V in 0.3 M oxalic acid at 15°C for 60 minutes. The well-ordered pore and cell structure was revealed by subjecting the porous anodic alumina to oxide dissolution treatment in a mixture of chromic acid and phosphoric acid. It was found that the manganese content above 1 wt% impaired the regularity of the cell and pore structure significantly, which can be attributed to the presence of secondary phases in the starting material with manganese content above 1 wt%. The pore diameter and interpore distance decreased with the addition of manganese into the substrates. The time variation of current density and the thickness of porous anodic alumina also decreased as a function of the manganese content in the substrates.

  17. Effects of Moisture Content on the Foundry Properties of Yola Natural Sand

    Directory of Open Access Journals (Sweden)

    Paul Aondona IHOM

    2012-08-01

    Full Text Available The effect of moisture content of Yola natural sand has been studied. The moisture content was varied from 1 to 9%. The effect of the moisture content on the green compression strength, green permeability and bulk density was investigated. Particle size distribution of the natural sand, the grain fineness number, average grain size, grain shape and the clay content of the natural sand were also studied. 5% moisture gave the optimum green compression strength of 118.6KN/m2. The dry compression strength increased with moisture content, an optimum value of 4000KN/m2 was obtained at 9% moisture. The Yola natural sand had a grain fineness number of 88.05AFS, average grain size of 335.78 microns and a clay content of 26%. A sand mixture containing 5% moisture was prepared and used to produce a test casting with aluminium scraps, the test casting was sound.

  18. What Combinations of Contents is Driving Popularity in IPTV-based Social Networks?

    Science.gov (United States)

    Bhatt, Rajen

    IPTV-based Social Networks are gaining popularity with TV programs coming over IP connection and internet like applications available on home TV. One such application is rating TV programs over some predefined genres. In this paper, we suggest an approach for building a recommender system to be used by content distributors, publishers, and motion pictures producers-directors to decide on what combinations of contents may drive popularity or unpopularity. This may be used then for creating a proper mixture of media contents which can drive high popularity. This may also be used for the purpose of catering customized contents for group of users whose taste is similar and thus combinations of contents driving popularity for a certain group is also similar. We use a novel approach for this formulation utilizing fuzzy decision trees. Computational experiments performed over real-world program review database shows that the proposed approach is very efficient towards understanding of the content combinations.

  19. Spectrophotometric determination of silicon in silumin matrix

    International Nuclear Information System (INIS)

    Samanta, Papu; Pandey, K.L.; Kumar, Pradeep; Bagchi, A.C.; Abdulla, K.K.

    2015-01-01

    In dispersion fuel, fissile material is dispersed in inert matrix. Aluminum-silicon-nickel (silumin) alloy is employed as inert matrix owing to its high thermal conductivity, high castability, high corrosion resistance. All these properties depend on the chemical composition and the structure of silumin. Silicon is stringent specification in silumin. A spectrophotometric method has been developed for the determination of silicon content in silumin matrix. Silumin matrix was fused with LiOH and subsequent dissolution in water along with few drops of conc. sulphuric acid. The molybodo-silicic formed by the addition of ammonium molybdate is reduced to molybdenum blue by ascorbic acid in the presence of antimony. The absorbance was measured at 810 nm. Aluminum and nickel were found to be non-interfering with the silicon determination. (author)

  20. Dietary calcium phosphate content and oat β-glucan influence gastrointestinal microbiota, butyrate-producing bacteria and butyrate fermentation in weaned pigs.

    Science.gov (United States)

    Metzler-Zebeli, Barbara U; Zijlstra, Ruurd T; Mosenthin, Rainer; Gänzle, Michael G

    2011-03-01

    This study aimed to evaluate the effects of oat β-glucan in combination with low- and high-dietary calcium phosphate (CaP) content on gastrointestinal bacterial microbiota, prevalence of butyrate-production pathway genes and fermentation end-products in 32 weaned pigs allocated to four diets: a cornstarch-casein-based diet with low [65% of the calcium (Ca) and phosphorous (P) requirement] and high CaP content (125% and 115% of the Ca and P requirement, respectively); and low and high CaP diets supplemented with 8.95% of oat β-glucan concentrate. Pigs were slaughtered after 14 days, and digesta were collected for quantitative PCR analysis, and quantification of short-chain fatty acids and lactate. The high CaP content reduced gastric lactate and streptococci and propionate in the large intestine. Oat β-glucan distinctly raised gastric bacterial numbers, and colonic lactobacilli and bifidobacteria. Although not reflected by gene copies of butyrate-production pathway genes, oat β-glucan also increased gastric, caecal and colonic butyrate concentrations, which may be favourable for intestinal development in weaned pigs. Thus, a high CaP content negatively affected the intestinal abundance of certain fermentation end-products, whereas oat β-glucan generally enhanced bacterial numbers and activity. The results emphasize the importance of the stomach for bacterial metabolism of oat β-glucan in weaned pigs. © 2010 Federation of European Microbiological Societies. Published by Blackwell Publishing Ltd. All rights reserved.

  1. Method of producing granulated ceramic nuclear fuels

    International Nuclear Information System (INIS)

    Wilkinson, W.L.

    1976-01-01

    For the production of granulated ceramic nuclear fuels with a grain size spectrum as narrow as possible it is proposed to suspend the nuclear fuel powder in a non-aqueous solvent with small content of hydrogen (e.g. chloridized hydrocarbons) while adding a binding agent and then dry it by means of rays. As binding agent polybutyl methane acrylate in dibutyl phthalate is proposed. The method is described by the example of UO 2 -powder in trichloroethylene. The dry granulated material is produced in one working step. (UWI) [de

  2. Analysis for Producing a Facsimile of the Cadastral Map of Varaždin

    Directory of Open Access Journals (Sweden)

    Mirko Husak

    2012-12-01

    Full Text Available This paper investigates and suggests methods for producing a facsimile of the 1 860 cadastral map of Varaždin. The methods used to produce the map, the coordinate systems, map contents, usage, maintenance and damage are described. Three samples from the map that display the elements of damage noted were researched, and the possibility of replacing damaged sections with undamaged sections using digital methods investigated. The sources available were the original cadastral colour map of Varaždin, along with the line art cadastral map and field cadastral sketches. The original colour and line art maps were scanned using the DeSkan Express scanning system for large formats. A flatbed UMAX Mirage II A3 scanner was used for scanning the field cadastral map. For the research image-processing, Adobe Photoshop CE 7.0 software was used, although it was primarily designed for processing photographs. The colour separation method was rejected from the start, since the map was made by hand. The paper discusses the possibility of copying and inserting missing parts from additional map sources, changing the colour of the paper to white or another colour, removing the map content added in red ink and lead pencil, and so on. The discussion is based on actual examples from the digital image. The conclusion suggests image-processing methods for achieving optimal results in producing a facsimile of the Varaždin cadastral map.Keywords: facsimile; cadastral map; map content; scanning; digital image processing

  3. Complete Genome Sequence of the Gamma-Aminobutyric Acid-Producing Strain Streptococcus thermophilus APC151.

    Science.gov (United States)

    Linares, Daniel M; Arboleya, Silvia; Ross, R Paul; Stanton, Catherine

    2017-04-27

    Here is presented the whole-genome sequence of Streptococcus thermophilus APC151, isolated from a marine fish. This bacterium produces gamma-aminobutyric acid (GABA) in high yields and is biotechnologically suitable to produce naturally GABA-enriched biofunctional yogurt. Its complete genome comprises 2,097 genes and 1,839,134 nucleotides, with an average G+C content of 39.1%. Copyright © 2017 Linares et al.

  4. Suitable alkaline for graphene peeling grown on metallic catalysts using chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Karamat, S., E-mail: shumailakaramat@gmail.com [Department of Physics, Middle East Technical University, Ankara 06800 (Turkey); COMSATS Institute of Information Technology, Islamabad 54000 (Pakistan); Sonuşen, S. [Sabancı Üniversitesi (SUNUM), İstanbul 34956 (Turkey); Çelik, Ü. [Nanomagnetics Instruments, Ankara (Turkey); Uysallı, Y. [Department of Physics, Middle East Technical University, Ankara 06800 (Turkey); Oral, A., E-mail: orahmet@metu.edu.tr [Department of Physics, Middle East Technical University, Ankara 06800 (Turkey)

    2016-04-15

    Graphical abstract: - Highlights: • Graphene layers were grown on Pt and Cu foil via ambient pressure chemical vapor deposition method and for the delicate removal of graphene from metal catalysts, electrolysis method was used by using different alkaline (sodium hydroxide, potassium hydroxide, lithium hydroxide and barium hydroxide). • The delamination speed of PMMA/graphene stack was higher during the KOH and LiOH electrolysis as compare to NaOH and Ba(OH){sub 2}. Ba(OH){sub 2} is not advisable because of the residues left on the graphene surface which would further trapped in between graphene and SiO{sub 2}/Si surface after transfer. The average peeling time in case of Pt electrode is ∼6 min for KOH and LiOH and ∼15 min for NaOH and Ba(OH){sub 2}. • Electrolysis method also works for the Cu catalyst. The peeling of graphene was faster in the case of Cu foil due to small size of bubbles which moves faster between the stack and the electrode surface. The average peeling time was ∼3–5 min. • XPS analysis clearly showed that the Pt substrates can be re-used again. Graphene layer was transferred to SiO{sub 2}/Si substrates and to the flexible substrate by using the same peeling method. - Abstract: In chemical vapor deposition, the higher growth temperature roughens the surface of the metal catalyst and a delicate method is necessary for the transfer of graphene from metal catalyst to the desired substrates. In this work, we grow graphene on Pt and Cu foil via ambient pressure chemical vapor deposition (AP-CVD) method and further alkaline water electrolysis was used to peel off graphene from the metallic catalyst. We used different electrolytes i.e., sodium hydroxide (NaOH), potassium hydroxide (KOH), lithium hydroxide (LiOH) and barium hydroxide Ba(OH){sub 2} for electrolysis, hydrogen bubbles evolved at the Pt cathode (graphene/Pt/PMMA stack) and as a result graphene layer peeled off from the substrate without damage. The peeling time for KOH and LiOH

  5. Suitable alkaline for graphene peeling grown on metallic catalysts using chemical vapor deposition

    International Nuclear Information System (INIS)

    Karamat, S.; Sonuşen, S.; Çelik, Ü.; Uysallı, Y.; Oral, A.

    2016-01-01

    Graphical abstract: - Highlights: • Graphene layers were grown on Pt and Cu foil via ambient pressure chemical vapor deposition method and for the delicate removal of graphene from metal catalysts, electrolysis method was used by using different alkaline (sodium hydroxide, potassium hydroxide, lithium hydroxide and barium hydroxide). • The delamination speed of PMMA/graphene stack was higher during the KOH and LiOH electrolysis as compare to NaOH and Ba(OH)_2. Ba(OH)_2 is not advisable because of the residues left on the graphene surface which would further trapped in between graphene and SiO_2/Si surface after transfer. The average peeling time in case of Pt electrode is ∼6 min for KOH and LiOH and ∼15 min for NaOH and Ba(OH)_2. • Electrolysis method also works for the Cu catalyst. The peeling of graphene was faster in the case of Cu foil due to small size of bubbles which moves faster between the stack and the electrode surface. The average peeling time was ∼3–5 min. • XPS analysis clearly showed that the Pt substrates can be re-used again. Graphene layer was transferred to SiO_2/Si substrates and to the flexible substrate by using the same peeling method. - Abstract: In chemical vapor deposition, the higher growth temperature roughens the surface of the metal catalyst and a delicate method is necessary for the transfer of graphene from metal catalyst to the desired substrates. In this work, we grow graphene on Pt and Cu foil via ambient pressure chemical vapor deposition (AP-CVD) method and further alkaline water electrolysis was used to peel off graphene from the metallic catalyst. We used different electrolytes i.e., sodium hydroxide (NaOH), potassium hydroxide (KOH), lithium hydroxide (LiOH) and barium hydroxide Ba(OH)_2 for electrolysis, hydrogen bubbles evolved at the Pt cathode (graphene/Pt/PMMA stack) and as a result graphene layer peeled off from the substrate without damage. The peeling time for KOH and LiOH was ∼6 min and for NaOH and

  6. Relation between feeding mechanisms and solidification mode in 380 aluminium alloy with different iron contents

    International Nuclear Information System (INIS)

    Tovio, D. O.; Gonzalez, A.C.; Mugica, G. W.; Cuyas, J. C.

    2003-01-01

    In the present work the effect of iron (0.15, 0.42 and 0.86%) content in feeding mechanisms for 380 aluminium alloy has been studied. The feeding capacity has been evaluated by a device that produces a barrier removable to allowing the movement of the inter dendritic liquid. The results show the flow of different quantity of liquid, it depends of the temperature of operating the device and of the iron content. For minimum and maximum iron content, the inter dendritic and bursts feeding mechanisms are fundamentally involved, for 0.42% of iron the feeding mechanisms was the inter dendritic. The authors establish this behavior by the solidification mode of alloy, which promotes the presence of particles of Si or plates of b-Al 3 FeDi phase, in the inter dendritic channels and produce the different feeding mechanisms. (Author) 15 refs

  7. Use a microwave oven to determine the moisture content of sunflower

    International Nuclear Information System (INIS)

    Backer, L.F.; Walz, A.W.

    1987-01-01

    Much of the sunflower crop in the major producing areas of the United States requires artificial drying because of late crop maturity. Plant growth regulators permit earlier harvest by accelerating the maturation rate of the plant; research indicates that use of the growth regulator would result in approximately 10-14 days earlier maturation. Effectiveness of the chemical is dependent on timely application at relatively high moisture contents (50 to 55 percent). A rapid means of determining seed moisture content is required so the chemical can be applied at the proper growth stage . Additionally, sunflower is often harvested at moisture contents of more than 17 percent. Most electronic moisture meters are not calibrated for moisture contents this high and the accuracy of most moisture meters decreases with increasing moisture content. A recent study has shown that a conventional microwave oven can successfully be used to very rapidly determine the moisture content of high moisture sunflower seeds to indicate proper growth stage for the application of plant growth regulators. The microwave oven could also be used with reasonable accuracy to check harvest moisture content down to about 15 percent. At lower moisture contents, it would be advisable to use a calibrated electronic moisture meter

  8. Correlating Lithium Hydroxyl Accumulation with Capacity Retention in V2O5 Aerogel Cathodes.

    Science.gov (United States)

    Wangoh, Linda W; Huang, Yiqing; Jezorek, Ryan L; Kehoe, Aoife B; Watson, Graeme W; Omenya, Fredrick; Quackenbush, Nicholas F; Chernova, Natasha A; Whittingham, M Stanley; Piper, Louis F J

    2016-05-11

    V2O5 aerogels are capable of reversibly intercalating more than 5 Li(+)/V2O5 but suffer from lifetime issues due to their poor capacity retention upon cycling. We employed a range of material characterization and electrochemical techniques along with atomic pair distribution function, X-ray photoelectron spectroscopy, and density functional theory to determine the origin of the capacity fading in V2O5 aerogel cathodes. In addition to the expected vanadium redox due to intercalation, we observed LiOH species that formed upon discharge and were only partially removed after charging, resulting in an accumulation of electrochemically inactive LiOH over each cycle. Our results indicate that the tightly bound water that is necessary for maintaining the aerogel structure is also inherently responsible for the capacity fade.

  9. Rheocasting of Al-Cu alloy A201 with different silver content

    CSIR Research Space (South Africa)

    Masuku, EP

    2008-09-01

    Full Text Available Rheocasting of alloys A206 and A201 was investigated in this study. Conical bars with different silver contents were produced using CSIR rheoprocess technology, together with high pressure die casting. The results showed that addition of Ag to alloy...

  10. Inability to produce a model of dialysis encephalopathy in the rat by aluminum administration.

    Science.gov (United States)

    Perry, T L; Yong, V W; Godolphin, W J; Sutter, M; Hansen, S; Kish, S J; Foulks, J G; Ito, M

    1987-04-01

    We attempted to produce a rat model of brain aluminum toxicity in order to explore whether or not aluminum accumulation produces the neurochemical changes observed in brains of patients who die with dialysis encephalopathy. Daily subcutaneous injection of Al(OH)3 caused marked elevation of serum aluminum concentrations, but did not increase brain aluminum contents, either in rats with normal renal function, or in rats with unilateral or 5/6 nephrectomies. LiCl pretreatment, which has been reported to cause irreversible renal failure, did not impair renal function nor aid in achieving elevated brain aluminum contents. No reductions in brain contents of gamma-aminobutyric acid (GABA) or in glutamic acid decarboxylase (GAD, E.C.4.1.1.15) and choline acetyltransferase (ChAT, E.C.2.3.1.6) activities were observed in aluminum-treated rats. We conclude that the rat is not a suitable laboratory animal to explore the role of aluminum toxicity in causing the GABA and ChAT deficits present in brains of hemodialyzed human patients.

  11. Using the Integrative Model to Explain How Exposure to Sexual Media Content Influences Adolescent Sexual Behavior

    Science.gov (United States)

    Bleakley, Amy; Hennessy, Michael; Fishbein, Martin; Jordan, Amy

    2011-01-01

    Published research demonstrates an association between exposure to media sexual content and a variety of sex-related outcomes for adolescents. What is not known is the mechanism through which sexual content produces this "media effect" on adolescent beliefs, attitudes, and behavior. Using the Integrative Model of Behavioral Prediction, this…

  12. Quality of Milk Pasteurized Produced By UD. Gading Mas During Storage in Refrigerator

    Directory of Open Access Journals (Sweden)

    Manik Eirry Sawitri

    2012-02-01

    Full Text Available The aim of this research was to study pasteurized milk quality produced by UD. Gading Mas on pH, Acidity, alcohol test and TPC during 5 days storage in refrigerator. On first day showed that  weight mass 1,06 (w/w; fat content 2,00 (g/100g,  protein content 3,02  (g/100g, Zn 1,67 ppm, Cu<0,005 ppm, Pb 0,02 ppm,  As  0,0120 ppm, Hg< 0,0002 ppm, Sn 1,60 ppm dan Cd < 0,001 ppm and organoleptic test included color, flavor and taste were normal. Pasteurized milk characteristic during 5 days refrigeration for pH were 6,57;6,58;6,73;6,60 and 6,50 respectively. Acidity were 1,147 %, 0,145 %, 0,145%, 0,157 %, 0,156 % and 0,175  % respectively. TPC were 6,16 x 101, 1,2. 104; 3,15.104, 0,42.106 and 3,5.108 respectively. It concluded that pasteurized milk produced by UD Gading Mas fulfilled SNI quality standard based on weight mass, pH, acidity, fat, protein, heavy metal content, organoleptic test and TPC.   Keywords: pasteurized milk, quality, refrigerator

  13. MoisturEC: an R application for geostatistical estimation of moisture content from electrical conductivity data

    Science.gov (United States)

    Terry, N.; Day-Lewis, F. D.; Werkema, D. D.; Lane, J. W., Jr.

    2017-12-01

    Soil moisture is a critical parameter for agriculture, water supply, and management of landfills. Whereas direct data (as from TDR or soil moisture probes) provide localized point scale information, it is often more desirable to produce 2D and/or 3D estimates of soil moisture from noninvasive measurements. To this end, geophysical methods for indirectly assessing soil moisture have great potential, yet are limited in terms of quantitative interpretation due to uncertainty in petrophysical transformations and inherent limitations in resolution. Simple tools to produce soil moisture estimates from geophysical data are lacking. We present a new standalone program, MoisturEC, for estimating moisture content distributions from electrical conductivity data. The program uses an indicator kriging method within a geostatistical framework to incorporate hard data (as from moisture probes) and soft data (as from electrical resistivity imaging or electromagnetic induction) to produce estimates of moisture content and uncertainty. The program features data visualization and output options as well as a module for calibrating electrical conductivity with moisture content to improve estimates. The user-friendly program is written in R - a widely used, cross-platform, open source programming language that lends itself to further development and customization. We demonstrate use of the program with a numerical experiment as well as a controlled field irrigation experiment. Results produced from the combined geostatistical framework of MoisturEC show improved estimates of moisture content compared to those generated from individual datasets. This application provides a convenient and efficient means for integrating various data types and has broad utility to soil moisture monitoring in landfills, agriculture, and other problems.

  14. Physicochemical Changes and Resistant-Starch Content of Extruded Cornstarch with and without Storage at Refrigerator Temperatures

    Directory of Open Access Journals (Sweden)

    David Neder-Suárez

    2016-08-01

    Full Text Available Effects of extrusion cooking and low-temperature storage on the physicochemical changes and resistant starch (RS content in cornstarch were evaluated. The cornstarch was conditioned at 20%–40% moisture contents and extruded in the range 90–130 °C and at screw speeds in the range 200–360 rpm. The extrudates were stored at 4 °C for 120 h and then at room temperature. The water absorption, solubility index, RS content, viscoelastic, thermal, and microstructural properties of the extrudates were evaluated before and after storage. The extrusion temperature and moisture content significantly affected the physicochemical properties of the extrudates before and after storage. The RS content increased with increasing moisture content and extrusion temperature, and the viscoelastic and thermal properties showed related behaviors. Microscopic analysis showed that extrusion cooking damaged the native starch structure, producing gelatinization and retrogradation and forming RS. The starch containing 35% moisture and extruded at 120 °C and 320 rpm produced the most RS (1.13 g/100 g after to storage at low temperature. Although the RS formation was low, the results suggest that extrusion cooking could be advantageous for RS production and application in the food industry since it is a pollution less, continuous process requiring only a short residence time.

  15. A one-step bioprocess for production of high-content fructo-oligosaccharides from inulin by yeast.

    Science.gov (United States)

    Wang, Da; Li, Fu-Li; Wang, Shi-An

    2016-10-20

    Commercial fructo-oligosaccharides (FOS) are predominantly produced from sucrose by transfructosylation process that presents a maximum theoretical yield below 0.60gFOSgSucrose(-1). To obtain high-content FOS, costly purification is generally employed. Additionally, high-content FOS can be produced from inulin by using endo-inulinases. However, commercial endo-inulinases have not been extensively used in scale-up production of FOS. In the present study, a one-step bioprocess that integrated endo-inulinase production, FOS fermentation, and non-FOS sugars removal into one reactor was proposed to produce high-content FOS from inulin. The bioprocess was implemented by a recombinant yeast strain JZHΔS-TSC, in which a heterologous endo-inulinase gene was expressed and the inherent invertase gene SUC2 was disrupted. FOS fermentation at 40°C from 200g/L chicory inulin presented the maximun titer, yield, and productivity of 180.2±0.8g/L, 0.9gFOSgInulin(-1), and 7.51±0.03g/L/h, respectively. This study demonstrated that the one-step bioprocess was simple and highly efficient. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. [Differential Effect and Mechanism of in situ Immobilization of Cadmium Contamination in Soil Using Diatomite Produced from Different Areas].

    Science.gov (United States)

    Zhu, Jian; Wang, Ping; Lin, Yan; Lei, Ming-jing; Chen, Yang

    2016-02-15

    In order to understand the difference of in situ immobilization effect and mechanism of Cd contamination in soil using diatomite produced from different areas, the test was conducted using diatomite produced from Yunnan Tengchong, Jilin Linjiang, Zhejiang Shengzhou and Henan Xinyang of China as modifiers to immobilize cadmium contamination in simulated soil. The results indicated that the diatomite from all the four producing areas could effectively immobilize available Cd in soil, decreasing the available Cd content in soil by 27.7%, 28.5%, 30.1% and 57.2%, respectively when the adding concentration was 30 g x kg(-1). Their ability for immobilizing available Cd in soil followed the sequence of Henan Xinyang > Zhejiang Shengzhou > Jilin Linjiang > Yunnan Tengchong. It was also found that the physical and chemical properties of diatomite played a main role in soil cadmium immobilization, lower bulk density, larger specific surface area, more micro pores and wider distribution range of aperture were more favorable for available Cd immobilization. The results also showed that, the diatomite could control Cd contamination by changing soil physical and chemical properties, among these properties, pH and organic matter content were the key factors, increasing soil pH value and organic matter content was favorable for available cadmium immobilization, while the soil water content had little effect on available cadmium immobilization. The control of soil cadmium contamination by using diatomite to change cation exchange capacity was limited by time in some degree. The diatomite produced from Henan Xinyang, Zhejiang Shengzhou and Yunnan Tengchong increased the soil pH value and organic matter content, and was favorable for available Cd immobilization, while the diatomite from Jilin Linjiang showed converse effect.

  17. Ethylene production, ACC and MACC content of freesia buds and florets.

    NARCIS (Netherlands)

    Spikman, G.

    1988-01-01

    Changes in ethylene production, ACC (1-aminocyclopropane-1-carboxylic acid) and MACC (1-(malonylamino)-cyclopropane-1-carboxylic acid) content of buds and florets of detached inflorescences were studied. Most of the ethylene produced by the inflorescences came from small buds at the apex. This

  18. Enzymatic pre-treatment of high content cellulosic feedstock improves biogas production

    Science.gov (United States)

    Animal wastes with high lignin and cellulosic contents can serve as the feedstock for biogas production (mainly methane) that could be used as alternative energy source. However, these high lignin and cellulosic feedstocks are quite recalcitrant to be readily utilized by methanogens to produce ben...

  19. Using of natural radioactivity for determination of phosphorus content in phosphate rocks, apatites and superphosphates

    Energy Technology Data Exchange (ETDEWEB)

    Magas, S; Kasprzak, K S; Gorski, Z [Politechnika Poznanska (Poland). Inst. Chemii Podstawowej

    1980-01-01

    A quick radiometric method of determination of phosphorus content in natural phosphate rocks, apatites and phosphorus fertilizers, obtained from them has been developed on the basis of uranium and the products of its radioactive decay contained in these materials. The uranium content in these materials amounts to 0.01/0.02%, and is for a given deposit proportional to the phosphorus content. The method is well fitted for laboratory quick determination of phosphorus content in raw-materials and products in factories producing phosphorus fertilizers and makes possible the automation of process and proportioning of sulphuric acid in production of superphosphates.

  20. Determination of oxygen content in steel using activation analysis with 14 MeV neutron

    International Nuclear Information System (INIS)

    Calado, C.E.

    1978-01-01

    In the quantitative analysis of oxygen in steel by fast neutron activation analysis the oxygen content is evaluated from the measured activity of 16 N produced. Steel s mples are irradiated in 14 MeV neutron flux. After irradiation the samples are pneumatically transfered to the counting terminal where activity is measured. Oxygen concentrations, are obtained by comparison with standards of specified oxygen content [pt

  1. The development of Facebook marketing utilizing Content marketing. Case: Pirjon Pakari Oy.

    OpenAIRE

    Lehtikangas, Pauliina

    2015-01-01

    The purpose of this thesis was to learn how to improve Pirjon Pakari Oy’s brand visibility and overall visibility on Facebook. This was done by trying to add value to the end customer by producing interesting and engaging posts to Pirjon Pakari Oy’s Facebook page. This case study utilized theory from content marketing in attempts to improve the marketing of “Pirjon” Facebook page and therefore a Facebook content marketing strategy was created for Pirjon Pakari Oy. This strategy was implemente...

  2. THE INFLUENCE OF THE EXTRACTION TEMPERATURE ON THE RENDEMENT AND PECTIN METHOXYL CONTENTS OF WATERHYACINTH (Eichornia crassipes (Mart Solms

    Directory of Open Access Journals (Sweden)

    Ika Daniarsari

    2010-06-01

    Full Text Available The purpose of this research is to find out the influence of the extraction temperature on the rendement and pectin methoxyl contents of waterhyacinth with the applied temperatures ranged from 60, 70, 80, 90 and 100 °C.The stages of this research involve extraction, precipitation, washing and drying. The pectin produced was, then, identified by reacting it with water, ethanol 96 %, NaOH and spectrophotometer IR. Its product was, then, compared to the comparing pectin. To determine the methoxyl contents, the acid - base titration was used. The resulting data were analysed and tested using One Direction Anava with SPSS 10.0 program. From the quantitative used by this study, pectin was produced. This is shown by the gel-formation. The rendements produced with the extraction temperatures of 60, 70, 80, 90 and 100 °C were 0,428 %; 0,487 %; 0,629 %; 0,774 % and 0,958% respectively. While its methoxyl contents were 3,879 %; 3,993 %; 4,413 %; 3,573 % and 2,837 %. Based on the analysed data, it was found that the treatment with the extraction temperature gives a significant influence on the rendement and pectin methoxyl contents of waterhyacinth. Keywords: extraction, pectin, methoxyl contents

  3. Refinement of the crystal structures of biomimetic weddellites produced by microscopic fungus Aspergillus niger

    Science.gov (United States)

    Rusakov, A. V.; Frank-Kamenetskaya, O. V.; Gurzhiy, V. V.; Zelenskaya, M. S.; Izatulina, A. R.; Sazanova, K. V.

    2014-05-01

    The single-crystal structures of four biomimetic weddellites CaC2O4 · (2 + x)H2O with different contents of zeolitic water ( x = 0.10-0.24 formula units) produced by the microscopic fungus Aspergillus niger were refined from X-ray diffraction data ( R = 0.029-0.038). The effect of zeolitic water content on the structural stability of weddellite was analyzed. The parameter a was shown to increase with increasing x due to the increase in the distance between water molecules along this direction. The water content and structural parameters of the synthesized weddellites are similar to those of weddellites from biofilms and kidney stones.

  4. Investigation of Continuous Gas Engine CHP Operation on Biomass Producer Gas

    DEFF Research Database (Denmark)

    Ahrenfeldt, Jesper; Henriksen, Ulrik Birk; Jensen, Torben Kvist

    2005-01-01

    More than 2000 hours of gas engine operation with producer gas from biomass as fuel has been conducted on the gasification CHP demonstration and research plant, named “Viking” at the Technical University of Denmark. The gas engine is an integrated part of the entire gasification plant. The excess...... operates with varying excess of air due to variation in gas composition and thus stoichiometry, and a second where the excess of air in the exhaust gas is fixed and the flow rate of produced gas from the gasifier is varying. The interaction between the gas engine and the gasification system has been...... investigated. The engine and the plant are equipped with continuously data acquisition that monitors the operation including the composition of the producer gas and the flow. Producer gas properties and contaminations have been investigated. No detectable tar or particle content was observed...

  5. Resin impregnation process for producing a resin-fiber composite

    Science.gov (United States)

    Palmer, Raymond J. (Inventor); Moore, William E. (Inventor)

    1994-01-01

    Process for vacuum impregnation of a dry fiber reinforcement with a curable resin to produce a resin-fiber composite, by drawing a vacuum to permit flow of curable liquid resin into and through a fiber reinforcement to impregnate same and curing the resin-impregnated fiber reinforcement at a sufficient temperature and pressure to effect final curing. Both vacuum and positive pressure, e.g. autoclave pressure, are applied to the dry fiber reinforcement prior to application of heat and prior to any resin flow to compact the dry fiber reinforcement, and produce a resin-fiber composite of reduced weight, thickness and resin content, and improved mechanical properties. Preferably both a vacuum and positive pressure, e.g. autoclave pressure, are also applied during final curing.

  6. Growth and artemisinin content of artemisia Annua L. As a result of gamma irradiation on shoot culture

    International Nuclear Information System (INIS)

    Tri Muji Ermayanti; Erwin Al Hafiizh; Andri Fadillah Martin; Arthur A Lelono; Wiguna Rahman

    2016-01-01

    Artemisinin is the main compound produced by Artemisia annua is used as antimalarial drug. Many research have been conducted in order to increase artemisinin content in A. annua so that it can be produced economically. In several plants, mutation can be induced by Gamma irradiation to increase their secondary metabolite production. The aim of this research was to investigate the growth and artemisinin content of A. annua after Gamma irradiation. Irradiation was conducted using in vitro shoot tips with 5-50 Gy. Survival rate, growth of shoot culture, ploidy level confirmation, acclimatization, growth of plants in the field and artemisinin content were recorded. The results showed that LD_5_0 of A. annua was 37 Gy, therefore, shoots only grew in the control environment in the laboratory, their growth in the field was inhibited. Irradiation with 50 Gy, shoots only grew for 8 weeks, and died afterwards. Irradiation dose affected on growth of plants in the field as well as their artemisinin content. (author)

  7. Plasticized chitosan/polyolefin films produced by extrusion.

    Science.gov (United States)

    Matet, Marie; Heuzey, Marie-Claude; Ajji, Abdellah; Sarazin, Pierre

    2015-03-06

    Plasticized chitosan and polyethylene blends were produced through a single-pass extrusion process. Using a twin-screw extruder, chitosan plasticization was achieved in the presence of an acetic acid solution and glycerol, and directly mixed with metallocene polyethylene, mPE, to produce a masterbatch. Different dilutions of the masterbatch (2, 5 and 10 wt% of plasticized chitosan), in the presence of ethylene vinyl acetate, EVA, were subsequently achieved in single screw film extrusion. Very small plasticized chitosan domains (number average diameter <5 μm) were visible in the polymeric matrix. The resulting films presented a brown color and increasing haze with chitosan plasticized content. Mechanical properties of the mPE films were affected by the presence of plasticized chitosan, but improvement was observed as a result of some compatibility between mPE and chitosan in the presence of EVA. Finally the incorporation of plasticized chitosan affected mPE water vapor permeability while oxygen permeability remained constant. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. New formulations of sunflower based bio-lubricants with high oleic acid content – VOSOLUB project

    Directory of Open Access Journals (Sweden)

    Leao J. D.

    2016-09-01

    Full Text Available VOSOLUB project is a demonstration project supported by Executive Agency for Small and Medium-sized Enterprises (EASME that aims at testing under real operating conditions new formulations of sunflower-based biolubricants with high oleic acid content. These biolubricant formulations (including hydraulic fluids, greases, and neat oil metal-working fluids will be tested in three European demonstrating sites. Their technical performance will be evaluated and compared to corresponding mineral lubricants ones. In order to cover the demand for the sunflower base oil, a European SMEs network will be established to ensure the supply of the base at a competitive market price. Results presented concerns the base oil quality confirmed to be in accordance with the specification required, in particular on Free Fatty acid content, Phosphorus content, rancimat induction time and oleic acid content (ITERG. The oil characteristics specific for lubricant application analyzed by BfB Oil Research under normalized methods, match with lubricant specifications requirement such as viscosity, cold & hot properties, surface properties, anti-oxidant properties and thermal stability, anti-wear and EP properties, anti-corrosion properties Performance of the new biolubricant have been assessed by formulators and TEKNIKER First results on the use of new lubricant on real condition for rail Grease (produced by RS CLARE and tested with Sheffield Supertram, Hydraulic oil (produced by BRUGAROLAS and cutting oil (produced by MOTUL TECH and tested with innovative machining, turning are described.

  9. The role of content marketing in social media content communities

    Directory of Open Access Journals (Sweden)

    Charmaine du Plessis

    2017-10-01

    Full Text Available Background: Content marketing has become a leading marketing technique in digital marketing communication and uses the point of view of consumers to build relationships by creating and sharing engaging content in social media that enhance their daily lives. Existing research on social media communities has focused mainly on social media marketing and virtual brand community perspectives while content marketing’s valuable and unobtrusive role in social media content communities has largely been overlooked. Objective: The purpose of this article was to investigate content marketing’s role in social media content communities to engage with the target audience in an innate manner. Method: This study made use of a directed, inductive content analysis of 51 practitioner documents relating to business-to-consumer content marketing practices to add another perspective to existing research on communities in social media. The content analysis was facilitated by using QDA Miner, a widely adopted and reliable qualitative data analysis software programme. Results: Three categories emerged from the data namely building content communities, platform-specific content and understanding channels. These categories provide sufficient evidence of how brands make use of social media content communities to connect with the target audience in an unobtrusive manner, in addition to being present in virtual brand communities. Conclusion: The findings make several contributions to the existing literature. Firstly, it provides a clearer distinction between brand and social media content communities. Secondly, it extends conceptions about social media communities to include content communities and, thirdly, it provides sufficient evidence of how content marketing could benefit a brand by naturally becoming part of social media conversations.

  10. Submerged Cultivation of Mycelium with High Ergothioneine Content from the Culinary-Medicinal Golden Oyster Mushroom, Pleurotus citrinopileatus (Higher Basidiomycetes).

    Science.gov (United States)

    Lin, Shin-Yi; Chien, Shih-Chang; Wang, Sheng-Yang; Mau, Jeng-Leun

    2015-01-01

    The optimization of submerged culture of the culinary-medicinal golden oyster mushroom, Pleurotus citrinopileatus, was studied using a one-factor-at-a-time, two-stage stimulation and central composite rotatable design to produce mycelia with high ergothioneine content. The optimal culture conditions for mycelia harvested at day 22 were a temperature of 25°C, an inoculation ratio of 5%, 2% glucose, 0.5% yeast extract, and adjustment of the initial pH value to 10. The biomass and ergothioneine content were 8.28 g/L and 10.65 mg/g dry weight (dw), respectively. The addition of an amino acid precursor increased the ergothioneine content of mycelia; cysteine was the most effective. In addition, the results obtained from central composite rotatable design showed that the recommended combination for cysteine, histidine, and methionine was 8, 4, and 0.5 mmol/L, respectively. The predicted ergothioneine content was 13.90 mg/g dw, whereas the experimental maximal ergothioneine content was 14.57 mg/g dw. With the addition of complex precursors and under optimal culture conditions, mycelia harvested at days 16-20 had higher ergothioneine content. Accordingly, the information obtained could be used to produce mycelia with high ergothioneine content.

  11. Ruminant and industrially produced trans fatty acids

    DEFF Research Database (Denmark)

    Stender, Steen; Astrup, Arne; Dyerberg, Jørn

    2008-01-01

    % of the fatty acids in trans form compared to the content in ruminant fat which generally does not exceed 6%. In Western Europe, including Scandinavia, the average daily intake of IP-TFA has decreased during the recent decade due to societal pressure and a legislative ban, whereas the intake of RP-TFA has......Fatty acids of trans configuration in our food come from two different sources - industrially produced partially hydrogenated fat (IP-TFA) used in frying oils, margarines, spreads, and in bakery products, and ruminant fat in dairy and meat products (RP-TFA). The first source may contain up to 60...

  12. Phenolics content and antioxidant capacity of commercial red fruit juices

    Directory of Open Access Journals (Sweden)

    Mitić Milan N.

    2011-01-01

    Full Text Available The content of phenolics: total phenols (TP, flavonoids (TF, anthocyanins (TA and hydroxicinnamic acid as well as the total antioxidant capacity (TAC in nine commercial red fruit juices (sour cherry, black currant, red grape produced in Serbia were evaluated. The total compounds content was measured by spectrophotometric methods, TAC was determined using DPPH assays, and individual anthocyanins and hydroxycinnamic acids was determined using HPLC-DAD methods. Among the examined fruit juices, the black currant juices contained the highest amounts of all groups of the phenolics and exhibited strong antioxidant capacity. The amount of anthocyanins determined by HPLC method ranged from 92.36 to 512.73 mg/L in red grape and black currant juices, respectively. The anthocyanins present in the investigated red fruit juices were derivatives of cyanidin, delphinidin, petunidin, peonidin and malvidin. The predominant phenolic acid was neoclorogenic acid in sour cherry, caffeic acid in black currant, and p-coumaric acid in black grape juices. Generally, the red fruit juices produced in the Serbia are a rich source of the phenolic, which show evident antioxidant capacity.

  13. Radioactivity Content in Phosphoric Acid Used for Fertilizer Production

    International Nuclear Information System (INIS)

    Ibrahiem, N.M.; Hamed, A.A.

    2003-01-01

    Uranium content in phosphoric acid used fertilizer production was measured by alpha spectrometry, laser fluorimetry high resolution gamma spectrometry. Also, polonium-210 content was determined in phosphoric acid by alpha spectrometry. Uranium-234 and uranium-238 concentrations, measured by alpha spectroscopy, were found to be 601 and 507 Bq I -1 , respectively. Total uranium content obtained by laser fluorimetry was about 545 BqI - (45.4ppm). Gamma spectroscopy analysis gave the concentrations of 40 K, 238 U, 235 U, 214 Pb, 214 Bi and 208 TI, as 17,644,19.5, 1.2,1.3 and 9.4 Bq I -1 , respectively. Polonium-210 concentration was found to be about 3.1 Bq I -1 . Uranium-232 and polonium-208 were used as yield tracers, for alpha measurements of uranium and polonium, respectively. Samples of the tri-super phosphate (TSP) and single-super phosphate (SSP) fertilizers and the phosphogypsum produced were also analyzed by gamma spectroscopy. Uranium content in both phosphate fertilizers was 3205 and 1440 Bq Kg -1 for 238 U and 83 and 35 Bq Kg -1 for, 235 U respectively

  14. Analysis of Selenium Contents in Plant Foods Consumed by Korean adults

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Okhee; Kim, Kangsung [Kyonghee Univ., Yongin (Korea, Republic of); Moon, Jonghwa; Chung, Yongsam [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    Se exhibited a relatively small range of adequate ingestion level for health. An accurate investigation of Se consumption in Korean population has been rare because the database of food containing selenium is rather small. The table of Se content in food is a basic tool for calculating selenium intake. Since diet is the main source of Se intake, the Se content in various foods and personal dietary practices would be primarily determined to evaluate the nutritional status of Se for a population. To evaluate the Se intake levels of a population, a Se food database should be generated based on data produced by high-precision analytical techniques. In addition, this database should contain the Se contents of foods that are regularly consumed by the studied population. Plant foods contain lower Se levels when compared to animal products. However, grains, potatoes, starches, and legumes have been the main sources of carbohydrates and proteins in traditional Korean diet. Since grains such as rice are a staple food and remain the most consumed foods in Korea, their contribution to dietary Se intake might be considerable. However, no reports on the selenium content from plant foods have been compiled for the Korean population. The goal of this study was to measure the Se content in common consumed plant foods such as grain, potatoes, legumes and their products. The legume rich in protein contained relatively high amount of Se when compared to other plant food type. The raw wheat and wheat product which have been imported from abroad showed higher amount of Se than rice mostly produced in Korea. The acquired Se value is useful to assess the Se intake of Korean adults from plant foods.

  15. Analysis of Selenium Contents in Plant Foods Consumed by Korean adults

    International Nuclear Information System (INIS)

    Lee, Okhee; Kim, Kangsung; Moon, Jonghwa; Chung, Yongsam

    2014-01-01

    Se exhibited a relatively small range of adequate ingestion level for health. An accurate investigation of Se consumption in Korean population has been rare because the database of food containing selenium is rather small. The table of Se content in food is a basic tool for calculating selenium intake. Since diet is the main source of Se intake, the Se content in various foods and personal dietary practices would be primarily determined to evaluate the nutritional status of Se for a population. To evaluate the Se intake levels of a population, a Se food database should be generated based on data produced by high-precision analytical techniques. In addition, this database should contain the Se contents of foods that are regularly consumed by the studied population. Plant foods contain lower Se levels when compared to animal products. However, grains, potatoes, starches, and legumes have been the main sources of carbohydrates and proteins in traditional Korean diet. Since grains such as rice are a staple food and remain the most consumed foods in Korea, their contribution to dietary Se intake might be considerable. However, no reports on the selenium content from plant foods have been compiled for the Korean population. The goal of this study was to measure the Se content in common consumed plant foods such as grain, potatoes, legumes and their products. The legume rich in protein contained relatively high amount of Se when compared to other plant food type. The raw wheat and wheat product which have been imported from abroad showed higher amount of Se than rice mostly produced in Korea. The acquired Se value is useful to assess the Se intake of Korean adults from plant foods

  16. Effects of Silica in Rice Husk Ash (RHA) in producing High Strength Concrete

    OpenAIRE

    Kartini, K; Nurul Nazierah, M.Y; Zaidahtulakmal, M.Z; Siti Aisyah, G

    2012-01-01

    High strength concrete (HSC) are known to have a higher amount of cement binder in the mix design properties with low w/b ratio. The high mass of cement content produced substantial heat liberation in the concrete due to the reaction between cement and water, which can lead to cracking. Additive likes silica fume is too expensive to use in the HSC in order to overcome the problems, however, the initiative of utilizing the rice husk ash (RHA) which have high silica content are apply for the de...

  17. Studies on MgNi-Based Metal Hydride Electrode with Aqueous Electrolytes Composed of Various Hydroxides

    Directory of Open Access Journals (Sweden)

    Jean Nei

    2016-08-01

    Full Text Available Compositions of MgNi-based amorphous-monocrystalline thin films produced by radio frequency (RF sputtering with a varying composition target have been optimized. The composition Mg52Ni39Co3Mn6 is identified to possess the highest initial discharge capacity of 640 mAh·g−1 with a 50 mA·g−1 discharge current density. Reproduction in bulk form of Mg52Ni39Co3Mn6 alloy composition was prepared through a combination of melt spinning (MS and mechanical alloying (MA, shows a sponge-like microstructure with >95% amorphous content, and is chosen as the metal hydride (MH alloy for a sequence of electrolyte experiments with various hydroxides including LiOH, NaOH, KOH, RbOH, CsOH, and (C2H54N(OH. The electrolyte conductivity is found to be closely related to cation size in the hydroxide compound used as 1 M additive to the 4 M KOH aqueous solution. The degradation performance of Mg52Ni39Co3Mn6 alloy through cycling demonstrates a strong correlation with the redox potential of the cation in the alkali hydroxide compound used as 1 M additive to the 5 M KOH aqueous solution. NaOH, CsOH, and (C2H54N(OH additions are found to achieve a good balance between corrosion and conductivity performances.

  18. THE LYMAN ALPHA REFERENCE SAMPLE: EXTENDED LYMAN ALPHA HALOS PRODUCED AT LOW DUST CONTENT

    International Nuclear Information System (INIS)

    Hayes, Matthew; Östlin, Göran; Duval, Florent; Guaita, Lucia; Melinder, Jens; Sandberg, Andreas; Schaerer, Daniel; Verhamme, Anne; Orlitová, Ivana; Mas-Hesse, J. Miguel; Otí-Floranes, Héctor; Adamo, Angela; Atek, Hakim; Cannon, John M.; Herenz, E. Christian; Kunth, Daniel; Laursen, Peter

    2013-01-01

    We report on new imaging observations of the Lyman alpha emission line (Lyα), performed with the Hubble Space Telescope, that comprise the backbone of the Lyman alpha Reference Sample. We present images of 14 starburst galaxies at redshifts 0.028 P20 , Lyα radii are larger than those of Hα by factors ranging from 1 to 3.6, with an average of 2.4. The average ratio of Lyα-to-FUV radii is 2.9. This suggests that much of the Lyα light is pushed to large radii by resonance scattering. Defining the Relative Petrosian Extension of Lyα compared to Hα, ξ Lyα = R Lyα P20 /R Hα P20 , we find ξ Lyα to be uncorrelated with total Lyα luminosity. However, ξ Lyα is strongly correlated with quantities that scale with dust content, in the sense that a low dust abundance is a necessary requirement (although not the only one) in order to spread Lyα photons throughout the interstellar medium and drive a large extended Lyα halo.

  19. Recycling radioactive scrap metal by producing concrete shielding with steel granules

    International Nuclear Information System (INIS)

    Sappok, M.

    1996-01-01

    Siempelkamp foundry at Krefeld, Germany, developed a method for recycling radioactively contaminated steel from nuclear installations. The material is melted and used for producing shielding plates, containers, etc., on a cast-iron basis. Because the percentage of stainless steel has recently increased significantly, problems in the production of high-quality cast iron components have also grown. The metallurgy, the contents of nickel and chromium especially, does not allow for the recycling of stainless steel in a percentage to make this process economical. In Germany, the state of the art is to use shielded concrete containers for the transport of low active waste; this concrete is produced by using hematite as an additive for increasing shielding efficiency. The plan was to produce steel granules from radioactive scrap metal as a substitute for hematite in shielding concrete

  20. Increased mannoprotein content in wines produced by Saccharomyces kudriavzevii×Saccharomyces cerevisiae hybrids.

    Science.gov (United States)

    Pérez-Través, Laura; Querol, Amparo; Pérez-Torrado, Roberto

    2016-11-21

    Several wine quality aspects are influenced by yeast mannoproteins on account of aroma compounds retention, lactic-acid bacterial growth stimulation, protection against protein haze and astringency reduction. Thus selecting a yeast strain that produces high levels of mannoproteins is important for the winemaking industry. In this work, we observed increased levels of mannoproteins in S. cerevisiae×S. kudriavzevii hybrids, compared to the S. cerevisiae strain, in wine fermentations. Furthermore, the expression of a key gene related to mannoproteins biosynthesis, PMT1, increased in the S. cerevisiae×S. kudriavzevii hybrid. We showed that artificially constructed S. cerevisiae×S. kudriavzevii hybrids also increased the levels of mannoproteins. This work demonstrates that either natural or artificial S. cerevisiae×S. kudriavzevii hybrids present mannoprotein overproducing capacity under winemaking conditions, a desirable physiological feature for this industry. These results suggest that genome interaction in hybrids generates a physiological environment that enhances the release of mannoproteins. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Effect of extrusion conditions on aflatoxin content of corn–peanut ...

    African Journals Online (AJOL)

    Corn-peanut extrudates and flakes were then produced at various combinations of feed moisture contents (17% and 21%,) barrel temperatures (140°C, 160°C and 180°C) and screw speeds (150 rpm,200 rpm and 250 rpm)in a double screw extruder under factorial design. The process parameters were recorded during the ...

  2. Effect Of Sprouting On Available Lysine Content Of Cowpea ( Vigna ...

    African Journals Online (AJOL)

    This study was conducted to determine the effect of sprouting on available Lysine content of cowpea (Vigna unguiculata) flour and the performance of the flour used for producing “moi – moi” (steamed bean cake). Cowpea seed was subjected to sprouting for different periods of 1 day, 2 days and 3 days for samples B, C and ...

  3. Hearth bread characteristics: Effect of protein quality, protein content, whole meal flour, DATEM, proving time, and their interactions

    NARCIS (Netherlands)

    Aamodt, A.; Magnus, E.M.; Færgestad, E.M.

    2005-01-01

    The effects of protein quality, protein content, ingredients, and baking process of flour blends on hearth loaves were studied. The flour blends varied in protein composition and content. Flours of strong protein quality produced hearth loaves with larger loaf volume, larger bread slice area, and

  4. Produced water reuse aiming reinjection; Reuso de agua produzida visando reinjecao

    Energy Technology Data Exchange (ETDEWEB)

    Louvisse, Ana Maria Travalloni; Hora, Jairo Maynard da Fonseca; Guilherme, Claudio [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2004-07-01

    As an oil reservoir goes aging, the BSW (water and solid content associated to the crude oil ) from the produced oil increase acutely. As this associated water is isolated from the crude oil, it presents several contaminants with concentrations above to that specified in the environmental norms for its discharge. Attending the environmental legislation, some times, is very difficult and can even enable the entire project. As the reservoir becomes old, enhance techniques are necessary to maintain the oil producing. A common recovery mechanism, called secondary recovery, is the water injection. Commonly the water for secondary recovery is not easily available. The main objective of this work is present a treatment system for produced water used in a specific field in the Northwest region. This treatment involves reinjection of this water after filtration. We will have a high environmental benefited, avoiding the discharge of produced water, highly toxic, and at the same time enhanced the oil production. In this work, we develop a method to modify the physical chemistry characteristics of the produced water and increase the treatment process efficiency. (author)

  5. CO2 and humidity removal system for extended Shuttle missions - Equilibrium testing and performance analysis

    Science.gov (United States)

    Davis, S. H.; Kissinger, L. D.

    1976-01-01

    In Shuttle orbiter cabins, lithium hydroxide (LiOH) canisters are currently planned to be used for CO2 adsorption and condensing heat exchangers for humidity control. In this paper a more effective CO2 and humidity removal method is proposed by replacing the LiOH component with HS-C adsorbent (a polyethylenimine coated acrylic ester), thus eliminating the low temperature constraints on the active thermal control system. Since the adsorption of CO2 and H2O are reversible, a double bed configuration operating cyclicly is planned to provide continuous atmospheric control. Apparatus and the experimental procedure to test the adsorption equilibrium are described and some of the indicative results, tabulated by computers, are presented with the help of exponential expressions and differential equations. By using a computer model of the Shuttle HS-C system, performance predictions are made.

  6. NASA ISS Portable Fan Assembly Acoustics

    Science.gov (United States)

    Boone, Andrew; Allen, Christopher S.; Hess, Linda F.

    2018-01-01

    The Portable Fan Assembly (PFA) is a variable speed fan that can be used to provide additional ventilation inside International Space Station (ISS) modules as needed for crew comfort or for enhanced mixing of the ISS atmosphere. This fan can also be configured with a Shuttle era lithium hydroxide (LiOH) canister for CO2 removal in confined areas partially of fully isolated from the primary Environmental Control and Life Support System (ECLSS) on ISS which is responsible for CO2 removal. This report documents noise emission levels of the PFA at various speed settings and configurations. It also documents the acoustic attenuation effects realized when circulating air through the PFA inlet and outlet mufflers and when operating in its CO2 removal configuration (CRK) with a LiOH canister (sorbent bed) installed over the fan outlet.

  7. The Context of Current Content Analysis of Gender Roles: An Introduction to a Special Issue

    Science.gov (United States)

    Popova, Lucy; Linz, Daniel G.

    2010-01-01

    The aim of this paper is to provide context for the quantitative content analyses of gender roles that are to be included in both parts of this special issue. First, a timeline of historical uses of the content analysis methodology is presented. Second, research objectives that frequently drive content analysis of gender roles are described; these include: to support feminist claims, to compare media with real life, to predict effects on audiences, and to detect effects of media producers on content. Third, previous content analyses published in Sex Roles and other gender-focused journals are reviewed and categorized in terms of medium, genre, time span, gender, and nationality. Finally, contributions of each of the articles in this special issue are outlined. PMID:20694031

  8. Recycling produced water for algal cultivation for biofuels

    Energy Technology Data Exchange (ETDEWEB)

    Neal, Justin N. [Los Alamos National Laboratory; Sullivan, Enid J. [Los Alamos National Laboratory; Dean, Cynthia A. [Los Alamos National Laboratory; Steichen, Seth A. [Los Alamos National Laboratory

    2012-08-09

    Algal growth demands a continuous source of water of appropriate salinity and nutritional content. Fresh water sources are scarce in the deserts of the Southwestern United States, hence, salt water algae species are being investigated as a renewable biofuel source. The use of produced water from oil wells (PW) could offset the demand for fresh water in cultivation. Produced water can contain various concentrations of dissolved solids, metals and organic contaminants and often requires treatment beyond oil/water separation to make it suitable for algae cultivation. The produced water used in this study was taken from an oil well in Jal, New Mexico. An F/2-Si (minus silica) growth media commonly used to cultivate Nannochloropsis salina 1776 (NS 1776) was prepared using the produced water (F/2-Si PW) taking into account the metals and salts already present in the water. NS 1776 was seeded into a bioreactor containing 5L of the (F/2-Si PW) media. After eleven days the optical density at 750 nm (an indicator of algal growth) increased from 0 to 2.52. These results indicate algae are able to grow, though inhibited when compared with non-PW media, in the complex chemical conditions found in produced water. Savings from using nutrients present in the PW, such as P, K, and HCO{sub 3}{sup -}, results in a 44.38% cost savings over fresh water to mix the F/2-Si media.

  9. Radiological quality of packaged waters produced in France

    International Nuclear Information System (INIS)

    Franques, Nathalie; Perrin, Marie-Line; Godet, Jean-Luc; Pineau, Cyril; Loyen, Jeanne; Brassac, Annette; Gleizes, Marc; Baudry, Michel

    2013-09-01

    Based on radionuclide and uranium analyses performed in 2012 by the IRSN on packaged waters produced in France, this report presents the main results on this national survey. The objectives were a systematic measurement of radioactivity indicators, a systematic measurement of uranium content, and a limited measurement of radon-222 content in some samples. After some recalls on the notions of radioactivity and exposure, on uranium and radon properties, and of the present regulation, this report presents the adopted methodology, and discusses the range and limitation of this study. It presents and comments the results of systematic analyses of spring and natural mineral waters (presence of tritium, global beta and alpha activity, uranium concentration), the results of measurements of radon-222, and the results of additional analyses of spring and natural mineral waters (main radionuclides, radium-226, uranium isotopes, other radionuclides). It reports the calculation of doses and the interpretation of results for waters which have been submitted to additional analyses

  10. Neutron producing reactions in PuBe neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Bagi, János [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU) (Germany); Lakosi, László; Nguyen, Cong Tam [Centre for Energy Research, Hungarian Academy of Sciences, Budapest (Hungary)

    2016-01-01

    There are a plenty of out-of-use plutonium–beryllium neutron sources in Eastern Europe presenting both nuclear safeguards and security issues. Typically, their actual Pu content is not known. In the last couple of years different non-destructive methods were developed for their characterization. For such methods detailed knowledge of the nuclear reactions taking place within the source is necessary. In this paper we investigate the role of the neutron producing reactions, their contribution to the neutron yield and their dependence on the properties of the source.

  11. Characterization and Ecology of Carboxymethylcellulase-Producing Anaerobic Bacterial Communities Associated with the Intestinal Tract of the Pinfish, Lagodon rhomboides

    OpenAIRE

    Stellwag, E. J.; Smith, T. D.; Luczkovich, J. J.

    1995-01-01

    Carboxymethylcellulase (CMCase)-producing obligate anaerobes were isolated from the intestinal tract contents but not the feeding habitat of seagrass-consuming pinfish. Taxonomic characterization of these CMCase-producing strains revealed four taxonomic clusters; three were clostridial and one was of unknown taxonomic affinity. Our results demonstrated that the CMCase-producing obligate anaerobe community from pinfish differed from functionally similar microbial communities in terrestrial her...

  12. The content of minerals and trace elements in meals

    International Nuclear Information System (INIS)

    Bognar, A.; Schelenz, R.; Gruenewald, T.; Frahm, H.; Heine, K.; Wiechen, A.; Bundesanstalt fuer Milchforschung, Kiel

    1981-07-01

    Within the frame work of the research programme 'School Feeding', 68 menu items of different producers were investigated for the content of the minerals calcium, chlorine, iron, potassium, magnesium, sodium and phosphorus, and for the trace elements antimony, barium, bromine, cesium, chromium, hafnium, iridium,cobalt, copper, manganese, mercury, rubidium, scandium, selenium, silver, strontium, tin and zinc. For the analytical determination of the elements, instrumental neutron activation analysis and X-ray fluorometry were applied. The studies showed that a calculation of the content of minerals and trace elements in meals on the basis of recipes and nutritive tables for raw foods is not justified, expect for sodium and phosphorus, because incorrect results can be obtained for the majority of meals. (orig./MG) [de

  13. METHODS OF REDUCTION OF FREE PHENOL CONTENT IN PHENOLIC FOAM

    Directory of Open Access Journals (Sweden)

    Bruyako Mikhail Gerasimovich

    2012-12-01

    method aimed at reduction of toxicity of phenolic foams consists in the introduction of a composite mixture of chelate compounds. Raw materials applied in the production of phenolic foams include polymers FRB-1A and VAG-3. The aforementioned materials are used to produce foams FRP-1. Introduction of 1% aluminum fluoride leads to the 40% reduction of the free phenol content in the foam. Introduction of crystalline zinc chloride accelerates the foaming and curing of phenolic foams. The technology that contemplates the introduction of zeolites into the mixture includes pre-mixing with FRB -1A and subsequent mixing with VAG-3; thereafter, the composition is poured into the form, in which the process of foaming is initiated. The content of free phenol was identified using the method of UV spectroscopy. The objective of the research was to develop methods of reduction of the free phenol content in the phenolic foam.

  14. Determination of ash content of coal by mass absorption coefficient measurements at two X-ray energies

    International Nuclear Information System (INIS)

    Fookes, R.A.; Gravitis, V.L.; Watt, J.S.

    1977-01-01

    A method for determining the ash content of coal is proposed. It involves measurements proportional to mass absorption coefficients of coal at two X-ray energies. These measurements can be made using X-ray transmission or scatter techniques. Calculations based on transmission of narrow beams of X-rays have shown that ash can be determined to about 1wt%(1 sigma) in coal of widely varying ash content and composition. Experimentally, ash content was determined to 0.67wt% by transmission techniques and 1.0wt% by backscatter techniques in coal samples from the Bulli seam, NSW, Australia, having ash in the range 11-34wt%. For samples with a much wider range of coal composition (7-53wt% ash and 0-25wt% iron in the ash), ash content was determined by backscatter measurements to 1.62wt%. The method produced ash determinations at least as accurate as those produced by the established technique which compensates for variation in iron content of the ash by X-ray fluorescence analysis for iron. Compared with the established technique, it has the advantage of averaging analysis over much larger volumes of coal, but the disadvantage that much more precise measurements of X-ray intensities are required. (author)

  15. Production and characterization refuse derived fuel (RDF) from high organic and moisture contents of municipal solid waste (MSW)

    Science.gov (United States)

    Dianda, P.; Mahidin; Munawar, E.

    2018-03-01

    Many cities in developing countries is facing a serious problems to dealing with huge municipal solid waste (MSW) generated. The main approach to manage MSW is causes environmental impact associated with the leachate and landfill gas emissions. On the other hand, the energy available also limited by rapid growth of population and economic development due to shortage of the natural resource. In this study, the potential utilized of MSW to produce refuse derived fuel (RDF) was investigate. The RDF was produced with various organic waste content. Then, the RDF was subjected to laboratory analysis to determine its characteristic including the calorific value. The results shows the moisture content was increased by increasing organic waste content, while the calorific value was found 17-36 MJ/kg. The highest calorific value was about 36 MJ/kg obtained at RDF with 40% organic waste content. This results indicated that the RDF can be use to substitute coal in main burning process and calcinations of cement industry.

  16. On the Creative Edge: Exploring Motivations for Creating Non-Suicidal Self-Injury Content Online.

    Science.gov (United States)

    Seko, Yukari; Kidd, Sean A; Wiljer, David; McKenzie, Kwame J

    2015-10-01

    The last decade has witnessed an exponential growth in user-generated online content featuring Non-Suicidal Self-Injury (NSSI), including photography, digital video, poems, blogging, and drawings. Although the increasing visibility of NSSI content has evoked public concern over potential health risks, little research has investigated why people are drawn to create and publish such content. This article reports the findings from a qualitative analysis of online interviews with 17 individuals who produce NSSI content. A thematic analysis of participants' narratives identified two prominent motives: self-oriented motivation (to express self and creativity, to reflect on NSSI experience, to mitigate self-destructive urges) and social motivation (to support similar others, to seek out peers, to raise social awareness). Participants also reported a double-edged impact of NSSI content both as a trigger and a deterrent to NSSI. © The Author(s) 2015.

  17. Depth enhancement of S3D content and the psychological effects

    Science.gov (United States)

    Hirahara, Masahiro; Shiraishi, Saki; Kawai, Takashi

    2012-03-01

    Stereoscopic 3D (S3D) imaging technologies are widely used recently to create content for movies, TV programs, games, etc. Although S3D content differs from 2D content by the use of binocular parallax to induce depth sensation, the relationship between depth control and the user experience remains unclear. In this study, the user experience was subjectively and objectively evaluated in order to determine the effectiveness of depth control, such as an expansion or reduction or a forward or backward shift in the range of maximum parallactic angles in the cross and uncross directions (depth bracket). Four types of S3D content were used in the subjective and objective evaluations. The depth brackets of comparison stimuli were modified in order to enhance the depth sensation corresponding to the content. Interpretation Based Quality (IBQ) methodology was used for the subjective evaluation and the heart rate was measured to evaluate the physiological effect. The results of the evaluations suggest the following two points. (1) Expansion/reduction of the depth bracket affects preference and enhances positive emotions to the S3D content. (2) Expansion/reduction of the depth bracket produces above-mentioned effects more notable than shifting the cross/uncross directions.

  18. New Tools to Convert PDF Math Contents into Accessible e-Books Efficiently.

    Science.gov (United States)

    Suzuki, Masakazu; Terada, Yugo; Kanahori, Toshihiro; Yamaguchi, Katsuhito

    2015-01-01

    New features in our math-OCR software to convert PDF math contents into accessible e-books are shown. A method for recognizing PDF is thoroughly improved. In addition, contents in any selected area including math formulas in a PDF file can be cut and pasted into a document in various accessible formats, which is automatically recognized and converted into texts and accessible math formulas through this process. Combining it with our authoring tool for a technical document, one can easily produce accessible e-books in various formats such as DAISY, accessible EPUB3, DAISY-like HTML5, Microsoft Word with math objects and so on. Those contents are useful for various print-disabled students ranging from the blind to the dyslexic.

  19. Homepage to distribute the anatomy learning contents including Visible Korean products, comics, and books.

    Science.gov (United States)

    Chung, Beom Sun; Chung, Min Suk

    2018-03-01

    The authors have operated the homepage (http://anatomy.co.kr) to provide the learning contents of anatomy. From the homepage, sectioned images, volume models, and surface models-all Visible Korean products-can be downloaded. The realistic images can be interactively manipulated, which will give rise to the interest in anatomy. The various anatomy comics (learning comics, comic strips, plastination comics, etc.) are approachable. Visitors can obtain the regional anatomy book with concise contents, mnemonics, and schematics as well as the simplified dissection manual and the pleasant anatomy essay. Medical students, health allied professional students, and even laypeople are expected to utilize the easy and comforting anatomy contents. It is hoped that other anatomists successively produce and distribute their own informative contents.

  20. Homepage to distribute the anatomy learning contents including Visible Korean products, comics, and books

    Science.gov (United States)

    Chung, Beom Sun

    2018-01-01

    The authors have operated the homepage (http://anatomy.co.kr) to provide the learning contents of anatomy. From the homepage, sectioned images, volume models, and surface models—all Visible Korean products—can be downloaded. The realistic images can be interactively manipulated, which will give rise to the interest in anatomy. The various anatomy comics (learning comics, comic strips, plastination comics, etc.) are approachable. Visitors can obtain the regional anatomy book with concise contents, mnemonics, and schematics as well as the simplified dissection manual and the pleasant anatomy essay. Medical students, health allied professional students, and even laypeople are expected to utilize the easy and comforting anatomy contents. It is hoped that other anatomists successively produce and distribute their own informative contents. PMID:29644104

  1. Content Maps: A Teaching and Assessment Tool for Content Knowledge

    Science.gov (United States)

    Ward, Phillip; Lehwald, Harry; Lee, Yun Soo

    2015-01-01

    Developing content knowledge in teachers presents a constant challenge for teacher educators. This article introduces a teaching and assessment tool called a "content map," which allows teacher educators, teachers, and coaches to conceptualize the scope, sequence, and relational characteristics of the content being taught. Content maps…

  2. Synthesis and protonation behavior of carboxylate-functionalized poly(propylene imine) dendrimers

    NARCIS (Netherlands)

    Duijvenbode, van R.C.; Rajanayagam, A.; Koper, G.J.M.; Baars, M.W.P.L.; Waal, de B.F.M.; Meijer, E.W.; Borkovec, M.

    2000-01-01

    Five generations of carboxylate-functionalized poly(propyleneimine) dendrimers have been synthesized starting from a double Michael addition of amine-functionalized poly(propyleneimine) dendrimers to methyl acrylate followed by basic hydrolysis using LiOH in a water/methanol mixture. The dendritic

  3. Treatment of offshore produced water - an effective membrane process

    International Nuclear Information System (INIS)

    Taylor, J.; Larson, R.; Scherer, B.

    1991-01-01

    The conference paper describes a new membrane technology being extremely effective in separating hydrocarbons from water streams. The membrane is composed of a completely natural cellulose and is resistant to all hydrocarbons and organic solvents, and preliminary tests have shown that it is resistant to fouling by oily molecules and calcium scaling. The membrane system being designed shows good potential for the treatment of offshore produced water with a hydrocarbon content well within present and emerging standards. 6 refs., 8 figs., 3 tabs

  4. An intelligent content discovery technique for health portal content management.

    Science.gov (United States)

    De Silva, Daswin; Burstein, Frada

    2014-04-23

    Continuous content management of health information portals is a feature vital for its sustainability and widespread acceptance. Knowledge and experience of a domain expert is essential for content management in the health domain. The rate of generation of online health resources is exponential and thereby manual examination for relevance to a specific topic and audience is a formidable challenge for domain experts. Intelligent content discovery for effective content management is a less researched topic. An existing expert-endorsed content repository can provide the necessary leverage to automatically identify relevant resources and evaluate qualitative metrics. This paper reports on the design research towards an intelligent technique for automated content discovery and ranking for health information portals. The proposed technique aims to improve efficiency of the current mostly manual process of portal content management by utilising an existing expert-endorsed content repository as a supporting base and a benchmark to evaluate the suitability of new content A model for content management was established based on a field study of potential users. The proposed technique is integral to this content management model and executes in several phases (ie, query construction, content search, text analytics and fuzzy multi-criteria ranking). The construction of multi-dimensional search queries with input from Wordnet, the use of multi-word and single-word terms as representative semantics for text analytics and the use of fuzzy multi-criteria ranking for subjective evaluation of quality metrics are original contributions reported in this paper. The feasibility of the proposed technique was examined with experiments conducted on an actual health information portal, the BCKOnline portal. Both intermediary and final results generated by the technique are presented in the paper and these help to establish benefits of the technique and its contribution towards effective

  5. Manual to radioactive waste management produced in hospitals, research and education centers

    International Nuclear Information System (INIS)

    Villasenor N, L.F.; Mejia L, M.

    1996-01-01

    This manual collects the experience on the disposal and management of the wastes produced in the preparation and application of radioactive material. Although the content is not so extensive, the authors have tried to provide the necessary guidelines and adequate information for the management of the wastes produced in hospitals and research and education centers. The objective of this work is to describe the basis and principles for the establishment of a minimization program, a segregation program and a provisional waste storage, in order to reduce the generation of wastes, personal exposure and the environmental impact. (authors). 5 refs

  6. Complete genome sequence of Agarivorans gilvus WH0801(T), an agarase-producing bacterium isolated from seaweed.

    Science.gov (United States)

    Zhang, Pujuan; Rui, Junpeng; Du, Zongjun; Xue, Changhu; Li, Xiangzhen; Mao, Xiangzhao

    2016-02-10

    Agarivorans gilvus WH0801(T), an agarase-producing bacterium, was isolated from the surface of seaweed. Here, we present the complete genome sequence, which consists of one circular chromosome of 4,416,600 bp with a GC content of 45.9%. This genetic information will provide insight into biotechnological applications of producing agar for food and industry. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Pigments in Extra-Virgin Olive Oils Produced in Tuscany (Italy) in Different Years

    Science.gov (United States)

    Lazzerini, Cristina; Domenici, Valentina

    2017-01-01

    Pigments are responsible for the color of olive oils, and are an important ingredient that is directly related to the quality of this food. However, the concentration of pigments can vary significantly depending on the climate conditions, harvesting time, and olive cultivars. In this work, we quantified the main pigments in several extra-virgin olive oils produced from a blend of three cultivars (Moraiolo, Frantoio, and Leccino) typical of Tuscany (Italy) harvested in three different years: 2012, 2013, and 2014. Pigments—namely, β-carotene, lutein, pheophytin A, and pheophytin B—were quantified by a method based on the mathematical analysis of the near ultraviolet-visible absorption spectra of the oils. Data were analyzed by a multivariate statistical approach. The results show that the pigments’ content of extra-virgin olive oils produced in 2014 can be well distinguished with respect to previous years. This can be explained by the anomalous climate conditions, which strongly affected Italy and, in particular, Tuscany, where the olives were harvested. This study represents an interesting example of how pigment content can be significant in characterizing olive oils. Moreover, this is the first report of pigment quantification in extra-virgin olive oils produced in Tuscany. PMID:28353651

  8. Effect of Zn content on the chemical conversion treatments of AZ91D magnesium alloy

    International Nuclear Information System (INIS)

    Hu Lifang; Meng Qingsen; Chen Shaoping; Wang Hao

    2012-01-01

    Highlights: ► The effect of Zn content on the chemical conversion process of Mg alloy was studied. ► The coating thickness grows up with the increase of the Zn content. ► The corrosion resistance of the coating is comparable if the Zn content below 2 wt.%. ► The corrosion resistance of the coating became poorer if the Zn content beyond 2 wt.%. - Abstract: In this study, four AZ91D magnesium plates with different Zn content were treated with chemical conversion treatments. The chemical conversion coating was examined using scanning electron microscope, optical microscope and glow discharge optical emission spectrometer. The testing results indicated that increase in Zn content produced a thicker chemical conversion coating. However, when the Zn content exceeded 2 wt.%, the thickness of the chemical conversion coating decreased. To investigate the chemical conversion mechanism, potentiodynamic polarization and electrochemical impedance spectroscopy were employed to evaluate the corrosion resistance of the magnesium substrate in 3.5 wt.% NaCl solution.

  9. Cadmium and lead contents in drinking milk from selected regions of Poland

    Directory of Open Access Journals (Sweden)

    Renata Pietrzak-Fiećko

    2013-09-01

    Full Text Available Background. Cadmium and lead are classified as toxic metals. Toxicity is attributed to the adverse effect on the human body, and therefore the content of these elements is analyzed in the environment and in food products. Studies conducted by many researchers indicate that more of cadmium and lead accumulate in products of plant origin, however, food products of animal origin are also not free from these compounds. The aim of this study was to determine the content of cadmium and lead in drinking milk originating from four selected milk producers from two different regions. Methods. A total of 28 milk samples were tested. The tested material was mineralized dry. To determine the content of the analyzed elements the Flame Atomic Absorption Spectrometry method was used. There were no significant differences in the content of heavy metals in the analyzed samples of milk. Results. None of the samples revealed the exceedance of the highest permissible level of these elements. Conclusions. Cadmium and lead content in tested drinking milk does not pose a threat to human health

  10. STATISTICAL ANALYSIS OF RAW SUGAR MATERIAL FOR SUGAR PRODUCER COMPLEX

    OpenAIRE

    A. A. Gromkovskii; O. I. Sherstyuk

    2015-01-01

    Summary. In the article examines the statistical data on the development of average weight and average sugar content of sugar beet roots. The successful solution of the problem of forecasting these raw indices is essential for solving problems of sugar producing complex control. In the paper by calculating the autocorrelation function demonstrated that the predominant trend component of the growth raw characteristics. For construct the prediction model is proposed to use an autoregressive fir...

  11. Producing bio-pellets from sunflower oil cake for use as an energy source

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, Yuichi; Kato, Hitoshi; Kanai, Genta; Togashi, Tatsushi [National Agricultural Research Center (Japan)], E-mail: kobay@affrc.go.jp

    2008-07-01

    Pellet fuels were produced from ground sunflower oil cake using a pelletizer. The length, hardness, and powder characteristics of dried pellets depend on the initial water content of the oil cake. The appropriate values of water contents were 19.9 - 21.0% w.b. Oil cake pellets were found to contain 6.07% ash and 20.99 MJ/kg caloric value, which are within the standard range of wood pellets. Combustion experiments using a commercial pellet stove demonstrate that oil cake pellets burn as well as wood pellets. Oil cake pellets are useful as a fuel alternative to wood pellets. (author)

  12. The Role of Content Aggregators In GEOValue

    Science.gov (United States)

    Wright, D. J.; Breyer, S.; Hogeweg, M.; Foust, J.; Jordan, L.; Plunkett, G.

    2016-12-01

    Data (aka content) in the form of numbers or layers, and transformed into information by way of maps, images, graphs, charts, tables, even stories, are foundational for a myriad of decision-makers. Recent advances in information technology, as well as civil remote sensing of the Earth, are rapidly allowing us to advance beyond mere static data collection and archiving, further enabling information awareness and understanding, and leading us towards knowledge and better decision making. However, such volumes, velocities, and varieties of data streams also bring with them serious dilemmas with regard to effective organization, cataloging, and easy access. This is where the role of aggregator comes in, with their provision of the necessary sustainability and reliability of information via proven, well-engineered platforms, all with the necessary interoperability and openness as guaranteed through the adoption of established standards. Information technology (IT) giants such as Google, Facebook, IBM and Apple are well known for aggregating just about every aspect of life in modern society, from our music to our mood swings. A use case of the Environmental Systems Research Institute (aka Esri) is presented as a geospatial aggregator. It has over the years, compiled, assembled and produced a carefully curated library of public content into a global "Living Atlas of the World," organized into different themes such as Earth observation, transportation, demographics, natural hazards, ecological land units, elevation, and more. Among a myriad of decision scenarios with this content to be presented is the tracking of sea ice in the Arctic, estimating potential impact to shipping lanes or coastal infrastructure, and forecasting future conditions. Esri as the main aggregator of Living Atlas content continues to welcome not only contributors who will publish new content to be included in this global Atlas, but fellow curators who will assist in reviewing, organizing, and even

  13. Tungsen--nickel--cobalt alloy and method of producing same

    International Nuclear Information System (INIS)

    Dickinson, J.M.; Riley, R.E.

    1977-01-01

    An improved tungsten alloy having a tungsten content of approximately 95 weight percent, a nickel content of about 3 weight percent, and the balance being cobalt of about 2 weight percent is described. A method for producing this tungsten--nickel--cobalt alloy is further described and comprises coating the tungsten particles with a nickel--cobalt alloy, pressing the coated particles into a compact shape, heating the compact in hydrogen to a temperature in the range of 1400 0 C and holding at this elevated temperature for a period of about 2 hours, increasing this elevated temperature to about 1500 0 C and holding for 1 hour at this temperature, cooling to about 1200 0 C and replacing the hydrogen atmosphere with an inert argon atmosphere while maintaining this elevated temperature for a period of about 1 / 2 hour, and cooling the resulting alloy to room temperature in this argon atmosphere

  14. Rapid discrimination of visual scene content in the human brain

    Science.gov (United States)

    Anokhin, Andrey P.; Golosheykin, Simon; Sirevaag, Erik; Kristjansson, Sean; Rohrbaugh, John W.; Heath, Andrew C.

    2007-01-01

    The rapid evaluation of complex visual environments is critical for an organism's adaptation and survival. Previous studies have shown that emotionally significant visual scenes, both pleasant and unpleasant, elicit a larger late positive wave in the event-related brain potential (ERP) than emotionally neutral pictures. The purpose of the present study was to examine whether neuroelectric responses elicited by complex pictures discriminate between specific, biologically relevant contents of the visual scene and to determine how early in the picture processing this discrimination occurs. Subjects (n=264) viewed 55 color slides differing in both scene content and emotional significance. No categorical judgments or responses were required. Consistent with previous studies, we found that emotionally arousing pictures, regardless of their content, produce a larger late positive wave than neutral pictures. However, when pictures were further categorized by content, anterior ERP components in a time window between 200−600 ms following stimulus onset showed a high selectivity for pictures with erotic content compared to other pictures regardless of their emotional valence (pleasant, neutral, and unpleasant) or emotional arousal. The divergence of ERPs elicited by erotic and non-erotic contents started at 185 ms post-stimulus in the fronto-central midline regions, with a later onset in parietal regions. This rapid, selective, and content-specific processing of erotic materials and its dissociation from other pictures (including emotionally positive pictures) suggests the existence of a specialized neural network for prioritized processing of a distinct category of biologically relevant stimuli with high adaptive and evolutionary significance. PMID:16712815

  15. Pyrolysis of blended animal manures to produce combustible gas and value-added charcoal adsorbent

    Science.gov (United States)

    Blended swine solids, chicken litter, and rye grass were pyrolyzed using a skid-mounted sytem. Produced gas composition was analyzed for major hydrocarbons and S-containing compounds. Charcoal was analyzed for its surface functional groups, contact angles, HHV, and total element contents. Some of th...

  16. Effect of Alkali Treatment and Fiber Content Variation on the Tensile ...

    African Journals Online (AJOL)

    The eect of alkali treatment and ber content variation on the tensile properties of coir ber reinforced cashew nut shell liquid (CNSL) composite was studied. Biocomposite consisting of coir bers and cashew nut shell liquid resin was produced using the hand lay-up technique. The bers were treated with 5% NaOH and varied ...

  17. Electrochemically produced alumina as TL detector

    International Nuclear Information System (INIS)

    Osvay, M.

    1996-01-01

    The goal of this work was to compare the TL properties of various electrochemically produced alumina layers (E-AIO) in order to investigate the effect of the electrolyte and the Mg content on the alloys. It has been found that the TL sensitivity of oxidised layers is more influenced by the type of electrolyte, than by the composition of alloy. Hard oxide layer evolved in reduction electrolyte has rather different character compared to other alumina production investigated. The effect of reducing media seems to be very important during preparation of alumina layer. One of the advantages properties of E-AIO is, that it serve a promising method to increase the measuring range of TL method above 10 kGy as well. (author)

  18. Measuring the incombustible content of mine dust using backscatter of low energy gamma rays

    International Nuclear Information System (INIS)

    Stewart, R.F.; Martin, J.W.

    1970-01-01

    Low energy gamma radiation directionally applied in a method, and by an adjustable apparatus to a layer of mine dust produces scattered gammas whose reflected radiation detected at a predetermined distance from the mine dust acts to cause the generation of an electrical control input for a meter indicating the incombustible content of the mine dust substantially independently of the effects on such indicating which are normally due to its bulk density and any moisture content thereof. (U.S.)

  19. Modeling on Fe-Cr microstructure: evolution with Cr content

    International Nuclear Information System (INIS)

    Diaz Arroyo, D.; Perlado, J.M.; Hernandez-Mayoral, M.; Caturla, M.J.; Victoria, M.

    2007-01-01

    Full text of publication follows: The minimum energy configuration of interstitials in the Fe-Cr system, which is the base for the low activation steels being developed in the European fusion reactor materials community, is determined by magnetism. Magnetism plays also a role in the atomic configurations found with increasing Cr content. Results will be presented from a program in which the microstructure evolution produced after heavy ion irradiation in the range from room temperature to 80 K is studied as a function of the Cr content in alloys produced under well controlled conditions, i.e. from high purity elements and with adequate heat treatment. It is expected that these measurements will serve as matrix for model validation. The first step in such modeling sequence is being performed by modeling the evolution of displacement cascades in Fe using the Dudarev -Derlet and Mendeleev potentials for Fe and the Caro potential for Fe-Cr. It is of particular interest to study the evolution of high-energy cascades, where an attempt will be made to clarify the role of the evolution of sub-cascades. Kinetic Monte Carlo (kMC) techniques will be used then to simulate the defect evolution. A new parallel kMC code is being implemented for this purpose. (authors)

  20. Effect of culinary and technological treatment of the farm animal products on the fission products content in them

    International Nuclear Information System (INIS)

    Meshalkin, G.S.

    1973-01-01

    The application of various procedures aimed at reducing the content of artificial radionuclides at the stage of technological and culinary processing of agricultural produce is considered. During the processing of milk and meat, which are basic farming produce, much of the contained fission products can be removed with low-value wastes. One of the more readily accessible methods of milk purification is recognized to be that of ion ixchange. A large role in reducing the radionuclide content of farming products is played by the time factor, i.e. the time spent for the manufacture and marketing of the products

  1. A study of real-time content marketing : formulating real-time content marketing based on content, search and social media

    OpenAIRE

    Nguyen, Thi Kim Duyen

    2015-01-01

    The primary objective of this research is to understand profoundly the new concept of content marketing – real-time content marketing on the aspect of the digital marketing experts. Particularly, the research will focus on the real-time content marketing theories and how to build real-time content marketing strategy based on content, search and social media. It also finds out how marketers measure and keep track of conversion rates of their real-time content marketing plan. Practically, th...

  2. Radioactivity content of books

    International Nuclear Information System (INIS)

    Lalit, B.Y.; Shukla, V.K.; Ramachandran, T.V.

    1981-01-01

    The natural and fallout radioactivity was measured in a large number of books produced in various countries after 1955. Results of these measurements showed that the books contained radioactivity due to fallout 137 Cs and 226 Ra, 228 Th and 40 K radioisotopes of primordial origin. Books printed in the U.S.A. had low radioactivity of 40K and 226 Ra origin compared to books printed in the European subcontinent. Books printed during high fallout rate (1962-64) or thereafter did not exhibit any significantly higher 137 Cs levels. The maximum radiation dose to the eyes calculated for the radioactivity content of the books was 0.8 μR/hr and the minimum was 0.07 μR/hr; most of the books were in the range 0.3-0.5 μR/hr. (U.K.)

  3. Expression of modified tocopherol content and profile in sunflower tissues.

    Science.gov (United States)

    Del Moral, Lidia; Fernández-Martínez, José M; Pérez-Vich, Begoña; Velasco, Leonardo

    2012-01-30

    Alpha-tocopherol is the predominant tocopherol form in sunflower seeds. Sunflower lines that accumulate increased levels of beta-, gamma- and delta-tocopherol in seeds as well as lines with reduced and increased total seed tocopherol content have been developed. The objective of this research was to evaluate whether the modified tocopherol levels are expressed in plant tissues other than seeds. Lines with increased levels of beta-, gamma- and delta-tocopherol in seeds also possessed increased levels of these tocopherols in leaves, roots and pollen. Correlation coefficients for the proportion of individual tocopherols in different plant tissues were significantly positive in all cases, ranging from 0.68 to 0.97. A line with reduced tocopherol content in seeds also showed reduced content in roots and pollen. Genetic modifications producing altered seed tocopherol profiles in sunflower are also expressed in leaves, roots and pollen. Reduced total seed tocopherol content is mainly expressed at the root and pollen level. The expression of tocopherol mutations in other plant tissues will enable further studies on the physiological role of tocopherols and could be of interest for early selection for these traits in breeding programmes. Copyright © 2011 Society of Chemical Industry.

  4. Analysis of total hydrogen content in palm oil and palm kernel oil using thermal neutron moderation method

    International Nuclear Information System (INIS)

    Akaho, E.H.K.; Dagadu, C.P.K.; Maaku, B.T.; Anim-Sampong, S.; Kyere, A.W.K.; Jonah, S.A.

    2001-01-01

    A fast and non-destructive technique based on thermal neutron moderation has been used for determining the total hydrogen content in two types of red palm oil (dzomi and amidze) and palm kernel oil produced by traditional methods in Ghana. An equipment consisting of an 241 Am-Be neutron source and 3 He neutron detector was used in the investigation. The equipment was originally designed for detection of liquid levels in petrochemical and other process industries. Standards in the form of liquid hydrocarbons were used to obtain calibration lines for thermal neutron reflection parameter as a function of hydrogen content. Measured reflection parameters with respective hydrogen content with or without heat treatment of the three edible palm oils available on the market were compared with a brand cooking oil (frytol). The average total hydrogen content in the local oil samples prior to heating was measured to be 11.62 w% which compared well with acceptable value of 12 w% for palm oils in the sub-region. After heat treatment, the frytol oil (produced through bleaching process) had the least loss of hydrogen content of 0.26% in comparison with palm kernel oil of 0.44% followed by dzomi of 1.96% and by amidze of 3.22%. (author)

  5. Determination of gel content and SEM morphology for sago-PVA blends film

    International Nuclear Information System (INIS)

    Sarada Idris; Zulkafli Ghazali; Kamarudin Hashim

    2006-01-01

    Blends of polyvinyl alcohol and sago starch have been prepared to evaluate the potential of producing biodegradable products. Glycerol was introduced in the blends to improve the flexibility of the films as plasticizer in order more flexible film. These blends have been subjected to electron beam irradiation to evaluate and characterized radiation effect on the blends. Subsequently films were produced from this blend. The gel content of un-irradiated and irradiated films as evidence of cross linking was measured and discussed. This paper also discuss the films morphology from Scanning Electron Microscopy(SEM) observation. (Author)

  6. Using advanced oxidation treatment for biofilm inactivation by varying water vapor content in air plasma

    Science.gov (United States)

    Ryota, Suganuma; Koichi, Yasuoka

    2015-09-01

    Biofilms are caused by environmental degradation in food factories and medical facilities. The inactivation of biofilms involves making them react with chemicals including chlorine, hydrogen peroxide, and ozone, although inactivation using chemicals has a potential problem because of the hazardous properties of the residual substance and hydrogen peroxide, which have slow reaction velocity. We successfully performed an advanced oxidation process (AOP) using air plasma. Hydrogen peroxide and ozone, which were used for the formation of OH radicals in our experiment, were generated by varying the amount of water vapor supplied to the plasma. By varying the content of the water included in the air, the main product was changed from air plasma. When we increased the water content in the air, hydrogen peroxide was produced, while ozone peroxide was produced when we decreased the water content in the air. By varying the amount of water vapor, we realized a 99.9% reduction in the amount of bacteria in the biofilm when we discharged humidified air only. This work was supported by JSPS KAKENHI Grant Number 25630104.

  7. Mortar modified with sulfonated polystyrene produced from waste plastic cups

    OpenAIRE

    MOTTA,L. A. C.; VIEIRA,J. G.; OMENA,T. H.; FARIA,F. A. C.; RODRIGUES FILHO,G.; ASSUNÇÃO,R. M. N.

    2016-01-01

    Abstract In this work, we studied the addition of sulfonated polystyrene produced from waste plastic cups as an admixture for mortars. Mortars were analyzed with polystyrene content of 0.0; 0.2; 0.6; 1.0 and 1.4% in relation to the cement mass. The influence of polystyrene on the mortars' properties was evaluated by the consistency index, water retention, water absorption, porosity, elasticity modulus, compressive strength, flexural strength, bond tensile strength and microscopy. The increase...

  8. A Content Analysis of 10 Years of Clinical Supervision Articles in Counseling

    Science.gov (United States)

    Bernard, Janine M.; Luke, Melissa

    2015-01-01

    This content analysis follows Borders's (2005) review of counseling supervision literature and includes 184 counselor supervision articles published over the past 10 years. Articles were coded as representing 1 of 3 research types or 1 of 3 conceptual types. Articles were then analyzed for main topics producing 11 topic categories.

  9. Naturalising Representational Content

    Science.gov (United States)

    Shea, Nicholas

    2014-01-01

    This paper sets out a view about the explanatory role of representational content and advocates one approach to naturalising content – to giving a naturalistic account of what makes an entity a representation and in virtue of what it has the content it does. It argues for pluralism about the metaphysics of content and suggests that a good strategy is to ask the content question with respect to a variety of predictively successful information processing models in experimental psychology and cognitive neuroscience; and hence that data from psychology and cognitive neuroscience should play a greater role in theorising about the nature of content. Finally, the contours of the view are illustrated by drawing out and defending a surprising consequence: that individuation of vehicles of content is partly externalist. PMID:24563661

  10. Investigating the link between radiologists’ gaze, diagnostic decision, and image content

    Science.gov (United States)

    Tourassi, Georgia; Voisin, Sophie; Paquit, Vincent; Krupinski, Elizabeth

    2013-01-01

    Objective To investigate machine learning for linking image content, human perception, cognition, and error in the diagnostic interpretation of mammograms. Methods Gaze data and diagnostic decisions were collected from three breast imaging radiologists and three radiology residents who reviewed 20 screening mammograms while wearing a head-mounted eye-tracker. Image analysis was performed in mammographic regions that attracted radiologists’ attention and in all abnormal regions. Machine learning algorithms were investigated to develop predictive models that link: (i) image content with gaze, (ii) image content and gaze with cognition, and (iii) image content, gaze, and cognition with diagnostic error. Both group-based and individualized models were explored. Results By pooling the data from all readers, machine learning produced highly accurate predictive models linking image content, gaze, and cognition. Potential linking of those with diagnostic error was also supported to some extent. Merging readers’ gaze metrics and cognitive opinions with computer-extracted image features identified 59% of the readers’ diagnostic errors while confirming 97.3% of their correct diagnoses. The readers’ individual perceptual and cognitive behaviors could be adequately predicted by modeling the behavior of others. However, personalized tuning was in many cases beneficial for capturing more accurately individual behavior. Conclusions There is clearly an interaction between radiologists’ gaze, diagnostic decision, and image content which can be modeled with machine learning algorithms. PMID:23788627

  11. Wisdom of the crowd or technicity of content? Wikipedia as a sociotechnical system

    NARCIS (Netherlands)

    Niederer, S.; van Dijck, J.

    2010-01-01

    Wikipedia is often considered as an example of ‘collaborative knowledge’. Researchers have contested the value of Wikipedia content on various accounts. Some have disputed the ability of anonymous amateurs to produce quality information, while others have contested Wikipedia’s claim to accuracy and

  12. Wisdom of the crowd or technicity of content? Wikipedia as a sociotechnical system

    NARCIS (Netherlands)

    Niederer, S.; van Dijck, J.; David, M.; Millward, P.

    2014-01-01

    Wikipedia is often considered as an example of ‘collaborative knowledge’. Researchers have contested the value of Wikipedia content on various accounts. Some have disputed the ability of anonymous amateurs to produce quality information, while others have contested Wikipedia’s claim to accuracy and

  13. Guide book of radioactive wastes collecting. Producers, from collection to storage

    International Nuclear Information System (INIS)

    2003-01-01

    This document, more particularly devoted to radioactive waste producers (except electronuclear industry), defines the technical specifications and the financial conditions relative to the taking over of their wastes by the ANDRA, the French national agency of radioactive wastes. Content: general principles, instructions manual of the taking over demand, practical conditions of wastes collecting, packaging and containers, specifications for each category of waste, particular cases, price table, disputes. (J.S.)

  14. PEMANFAATAN MINYAK SAWIT MERAH DALAM PEMBUATANBISKUIT KACANG KAYA BETA KAROTEN [Utilization of Red Palm Oil To Produce BetaCarotene-Rich Nuts Biscuit

    Directory of Open Access Journals (Sweden)

    Robiyansyah Robiyansyah

    2017-03-01

    Full Text Available The purpose of this research was to get formulation of red palm oil and cooking oil to produce nuts biscuits with the best organoleptic properties. The formula consisted of red palm oil and cooking oil mixture with 6 comparisons: (0:100, (20:80, (40:60, (60:40, (80:20 and (100:0. These formula were then used as basis to produce nuts biscuits. Observation was done on the organoleptic properties (aroma, texture, taste and color for all biscuits for all samples, while  proximates test (water, fat,protein,ash content and betacarotene content were done only for the best formulation. The data were descriptively analyzed and presented in tables and graphs. The best organoleptic properties of these betacarotene rich nuts biscuits was formulation of 20:80. This biscuits had water content 1,42%, ash content 1,21%, fat content 32,60%, protein content 12,59%, and the total of beta carotene 347,15 ppm, with the less normal for aroma (4,55, less crunchy for the texture (4,40, distinctive flavor beans for the taste (4,28, and yellowish for the color (4,50. Keywords: β-carotene, nuts biscuits,red palm oil.

  15. The exploration of Lanthanum based perovskites and their complementary electrolytes for the supercapacitor applications

    Directory of Open Access Journals (Sweden)

    Nadarajan Arjun

    Full Text Available In this study, four different kinds of perovskite powders (LaMnO3, LaFeO3, LaCrO3, and LaNiO3 were prepared and investigated as anode materials for supercapacitor. The as-prepared powders were blended with active carbon and subsequently coated on the nickel plates as the collector layer of the supercapacitors. Three different types of the aqueous solutions (3 M KCl, 1 M LiOH, and 3 M LiOH were respectively served as the electrolytes for the supercapacitor. The morphology and crystalline phase were characterized by transmission electron microscopy and XRD. The electrical capacity and impedance were measured by the electrochemical capacitance voltage analyzer and impedance spectroscopy. The profiles of specific capacitance of the four different anodic electrodes and three different electrolytes were implemented. The impedance results indicated that four asymmetric pseudocapacitors didn’t show any Warburg-type line and semi-circle line in the low-frequency region. According to the CV profiles, the intrinsic LaNiO3 exhibits the highest specific capacitance of 106.58 F/g in 3 M LiOH. Furthermore, the 98% of the initial capacitance of LaNiO3 was retained after 500 charge-discharge life cycles at the maximum current density of 1 A/g. The efficient charge storage of LaNiO3 was attributed by the anion intercalated redox reactions along with the suitability of electrode-electrolyte interactions. Keywords: Perovskite, Lanthanum nickel oxide, Pseudocapacitance, Asymmetric supercapacitor, Oxygen de-intercalation

  16. Development of micro-coulometry for measuring oxygen content in copper oxides

    International Nuclear Information System (INIS)

    Sato, Fumiaki; Fujihara, Masaaki; Kambe, Shiro; Ishii, Osamu

    2006-01-01

    A micro-coulometry system was newly developed and employed for measuring the oxygen content in copper oxides using a reduced amount of material. To achieve this reduction in sample size, Ar flow rate, and coulometric current were optimized. When using 5.0 mg of YBa 2 Cu 3 O 6.71 , which is about 1/10 the amount used in conventional coulometry, the oxygen content was successfully determined to be 6.68 ± 0.03, Ar flow rate, and coulometric current were 0.1 l/min, and 1.0 mA, respectively. It was found to be necessary to continue to pass Ar through the solution before coulometry more than ten minutes and during the coulometric measurement. This method will be useful for measuring the oxygen content of oxide samples smaller than 10 mg, i.e. oxide materials produced in small quantities for electronic applications

  17. Nuclear DNA contents of Echinchloa crus-galli and its Gaussian relationships with environments

    Science.gov (United States)

    Li, Dan-Dan; Lu, Yong-Liang; Guo, Shui-Liang; Yin, Li-Ping; Zhou, Ping; Lou, Yu-Xia

    2017-02-01

    Previous studies on plant nuclear DNA content variation and its relationships with environmental gradients produced conflicting results. We speculated that the relationships between nuclear DNA content of a widely-distributed species and its environmental gradients might be non-linear if it was sampled in a large geographical gradient. Echinochloa crus-galli (L.) P. Beauv. is a worldwide species, but without documents on its intraspecific variation of nuclear DNA content. Our objectives are: 1) to detect intraspecific variation scope of E. crus-galli in its nuclear DNA content, and 2) to testify whether nuclear DNA content of the species changes with environmental gradients following Gaussian models if its populations were sampled in a large geographical gradient. We collected seeds of 36 Chinese populations of E. crus-galli across a wide geographical gradient, and sowed them in a homogeneous field to get their offspring to determine their nuclear DNA content. We analyzed the relationships of nuclear DNA content of these populations with latitude, longitude, and nineteen bioclimatic variables by using Gaussian and linear models. (1) Nuclear DNA content varied from 2.113 to 2.410 pg among 36 Chinese populations of E. crus-galli, with a mean value of 2.256 pg. (2) Gaussian correlations of nuclear DNA content (y) with geographical gradients were detected, with latitude (x) following y = 2.2923*e -(x - 24.9360)2/2*63.79452 (r = 0.546, P correlations of its Nuclear DNA content with geographical and most bioclimatic gradients.

  18. Digital Content Strategies

    OpenAIRE

    Halbheer, Daniel; Stahl, Florian; Koenigsberg, Oded; Lehmann, Donald R

    2013-01-01

    This paper studies content strategies for online publishers of digital information goods. It examines sampling strategies and compares their performance to paid content and free content strategies. A sampling strategy, where some of the content is offered for free and consumers are charged for access to the rest, is known as a "metered model" in the newspaper industry. We analyze optimal decisions concerning the size of the sample and the price of the paid content when sampling serves the dua...

  19. Biodiesel from the seed oil of Treculia africana with high free fatty acid content

    Energy Technology Data Exchange (ETDEWEB)

    Adewuyi, Adewale [Redeemer' s University, Department of Chemical Sciences, Faculty of Natural Sciences, Redemption City, Ogun State (Nigeria); Oderinde, Rotimi A.; Ojo, David F.K. [University of Ibadan, Industrial Unit, Department of Chemistry, Ibadan, Oyo State (Nigeria)

    2012-12-15

    Oil was extracted from the seed of Treculia africana using hexane. The oil was characterized and used in the production of biodiesel. Biodiesel was produced from the seed oil of T. africana using a two-step reaction system. The first step was a pretreatment which involved the use of 2 % sulfuric acid in methanol, and secondly, transesterification reaction using KOH as catalyst. Saponification value of the oil was 201.70 {+-} 0.20 mg KOH/g, free fatty acid was 8.20 {+-} 0.50 %, while iodine value was 118.20 {+-} 0.50 g iodine/100 g. The most dominant fatty acid was C18:2 (44 %). The result of the method applied showed a conversion which has ester content above 98 %, flash point of 131 {+-} 1.30 C, and phosphorus content below 1 ppm in the biodiesel. The biodiesel produced exhibited properties that were in agreement with the European standard (EN 14214). This study showed that the high free fatty acid content of T. africana seed oil can be reduced in a one-step pretreatment of esterification reaction using H{sub 2}SO{sub 4} as catalyst. (orig.)

  20. Method for creating high carbon content products from biomass oil

    Science.gov (United States)

    Parker, Reginald; Seames, Wayne

    2012-12-18

    In a method for producing high carbon content products from biomass, a biomass oil is added to a cracking reactor vessel. The biomass oil is heated to a temperature ranging from about 100.degree. C. to about 800.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to crack the biomass oil. Tar is separated from the cracked biomass oil. The tar is heated to a temperature ranging from about 200.degree. C. to about 1500.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to reduce the tar to a high carbon content product containing at least about 50% carbon by weight.

  1. Gene effects and combining abilities for oil content in sunflower

    Directory of Open Access Journals (Sweden)

    Jocković Milan

    2014-01-01

    Full Text Available Considering the worldwide importance of sunflower oil, objective of this study was to evaluate gene effects and combining abilities of six sunflower open pollinated varieties. Varieties were crossed according to incomplete diallel method and produced fifteen F1 progenies. Comparing the mean values of F1 progenies to parents mean in most cases superdominance was expressed as a mode of inheritance. Nonetheless, dominance of better parent and partial dominance of better parent were also recorded as a mode of inheritance. GCA/SCA ratio indicated greater importance of non-additive genetic component in oil content expression. The genetic variance analysis showed that dominant component was more important and dominant genes prevailed compared to recessive genes for oil content in sunflower.

  2. The role of content marketing in social media content communities

    OpenAIRE

    Charmaine du Plessis

    2017-01-01

    Background: Content marketing has become a leading marketing technique in digital marketing communication and uses the point of view of consumers to build relationships by creating and sharing engaging content in social media that enhance their daily lives. Existing research on social media communities has focused mainly on social media marketing and virtual brand community perspectives while content marketing’s valuable and unobtrusive role in social media content communities has largely bee...

  3. Formation of extracellular polymeric substances from acidogenic sludge in H2-producing process.

    Science.gov (United States)

    Sheng, Guo-Ping; Yu, Han-Qing

    2007-02-01

    In this study, the formation of extracellular polymeric substances (EPS) and surface characteristics of an acidogenic sludge in anaerobic H(2)-producing process was investigated. Results show that carbohydrates, proteins, and humic substances were the dominant components in bound EPS (BEPS), while in soluble EPS (SEPS), carbohydrates were the main component. The total content of BEPS initially increased but then kept almost unchanged during fermentation from 25 to 35 h; after that, it slightly decreased. The total content of SEPS increased to 172.5 +/- 0.05 mg C g(-1) volatile suspended solid with the time that increased to 23.5 h, and then rapidly decreased until 43 h; thereafter, it kept almost unchanged. The SEPS had good correlations with the specific H(2) production rate, substrate degradation rate, and specific aqueous products formation rate, but the BEPS seemed to have no such correlations with these specific rates. Results also confirm that part of EPS could be utilized by the H(2)-producing sludge. As the substrate was in short supply, the EPS would be hydrolyzed to sever as carbon and energy source.

  4. Physicochemical and microbiological characterization of cassava flower honey samples produced by africanized honeybees

    Directory of Open Access Journals (Sweden)

    Lucimar Peres de Moura Pontara

    2012-09-01

    Full Text Available Cassava producers in the region of Marília-São Paulo are integrating their farming activity with beekeeping to diversify their income. The aim of this study was to evaluate the physicochemical and microbiological quality of honey samples produced by Africanized honeybees Apis mellifera from cassava flower in 2008. Analysis were carried out for pH, total soluble solids (TSS, acidity, moisture, reducing and total sugars, apparent sucrose, hydroxymethylfurfural, color, ash, proteins, water insoluble solids, diastasic activity, mineral content, microbiological evaluations, and mineral and hydrocyanic acid (HCN content. The honey samples showed physicochemical and microbiological characteristics favorable to commercialization, with the exception of apparent sucrose and acidity, which show the need for a narrow focus of attention to the honey maturation degree at the harvest time and more careful monitoring during production and processing. The commercialization of Brazilian cassava honey, still little explored, can be widely spread in the market since the levels of hydrocyanic acid (HCN showed no consumption risk; in addition the simultaneous production of honey and cassava provides an alternative to family income increase.

  5. Hydrothermally Processed Oxide Nanostructures and Their Lithium–ion Storage Properties

    Directory of Open Access Journals (Sweden)

    Kim Yong-Jin

    2010-01-01

    Full Text Available Abstract Y- and Si-based oxide nanopowders were synthesized by a hydrothermal reaction of Y or Si powders with NaOH or LiOH aqueous solution. Nanoparticles with different morphology such as elongated nanospheres, flower-like nanoparticles and nanowires were produced by a control of processing parameters, in particular, the starting composition of solution. The preliminary result of electrochemical examination showed that the hydrothermally processed nanowires exhibit high initial capacities of Li-ion storage: 653 mAh/g for Y2O3 nanowires as anode materials and 186 mAh/g for Li2Si2O5 nanowires as cathode materials in a Li secondary cell. Compared to the powder with elongated sphere or flower-like shapes, the nanowires showed a higher Li-ion capacity and a better cycle property.

  6. Investigating the Link Between Radiologists Gaze, Diagnostic Decision, and Image Content

    Energy Technology Data Exchange (ETDEWEB)

    Tourassi, Georgia [ORNL; Voisin, Sophie [ORNL; Paquit, Vincent C [ORNL; Krupinski, Elizabeth [University of Arizona

    2013-01-01

    Objective: To investigate machine learning for linking image content, human perception, cognition, and error in the diagnostic interpretation of mammograms. Methods: Gaze data and diagnostic decisions were collected from six radiologists who reviewed 20 screening mammograms while wearing a head-mounted eye-tracker. Texture analysis was performed in mammographic regions that attracted radiologists attention and in all abnormal regions. Machine learning algorithms were investigated to develop predictive models that link: (i) image content with gaze, (ii) image content and gaze with cognition, and (iii) image content, gaze, and cognition with diagnostic error. Both group-based and individualized models were explored. Results: By pooling the data from all radiologists machine learning produced highly accurate predictive models linking image content, gaze, cognition, and error. Merging radiologists gaze metrics and cognitive opinions with computer-extracted image features identified 59% of the radiologists diagnostic errors while confirming 96.2% of their correct diagnoses. The radiologists individual errors could be adequately predicted by modeling the behavior of their peers. However, personalized tuning appears to be beneficial in many cases to capture more accurately individual behavior. Conclusions: Machine learning algorithms combining image features with radiologists gaze data and diagnostic decisions can be effectively developed to recognize cognitive and perceptual errors associated with the diagnostic interpretation of mammograms.

  7. Rheological properties and mineral content of buckwheat enriched wholegrain wheat pasta

    Directory of Open Access Journals (Sweden)

    Nedeljković Nataša

    2014-01-01

    Full Text Available Light buckwheat flour (LBF was used to substitute 20% of whole wheat flour (WWF in the formulation of wholegrain wheat pasta. Wholegrain wheat pasta (WWP and buckwheat enriched wholegrain wheat pasta (BWWP were produced on an industrial scale. Substitution level of buckwheat flour (20% was based on previously conducted rheological tests on LBF/WWF blends which were performed using 10, 20 and 30% of LBF. The obtained Mixolab profiles have indicated that wheat blend containing 20% LBF expressed the most similar rheological parameters to WWF. Proximate composition, cooking quality and mineral content of BWWP were analyzed and compared with those of WWP. The substitution of WWF with LBF in the pasta formulation resulted in significantly increased (P < 0.05 contents of P, Mg, K and Zn compared to WWP in dry pasta. The reduction in mineral content of BWWP during cooking was significantly higher (P < 0.05 compared to WWP. The content of P, Mg and K were at same level in both type of pasta after cooking. The obtained results suggest that enrichment of WWP with LBF at the level of 20% did not improve the mineral content of cooked pasta, although increase in minerals was observed in dry pasta. [Projekat Ministarstva nauke Republike Srbije, br. TR31029

  8. Blackberry Vinegar Produced By Successive Acetification Cycles: Production, Characterization And Bioactivity Parameters

    Directory of Open Access Journals (Sweden)

    Mário Antônio Alves da Cunha

    Full Text Available ABSTRACT: Blackberry vinegar was produced in successive acetification cycles and content of total phenolics, anthocyanins and antioxidant activity were evaluated along the production. Firstly, blackberry wine was obtained in bench-scale bioreactor, being verified 0.39 g/g ethanol yield, 1.78 g/L.h volumetric productivity and 76% efficiency. After, three successive acetification cycles were conducted efficiently in grapia barrel with average acetic acid production of 51.6 g/L, 72.2 % acetic acid yield and 0.4 g/L.h volumetric productivity. Appreciable contents of polyphenolic compounds, anthocyanins and high antioxidant activity were observed in the raw material, wine and vinegar obtained in each cycle of acetic acid transformation. Acetic acid transformation led the small reduction of antioxidant activity compared to alcoholic fermentation, but the antioxidant potential was maintained along the cycles. The content of total phenolics and anthocyanins also suffered a reduction in step of acetification.

  9. Characterization of activated carbon produced from urban organic waste

    Directory of Open Access Journals (Sweden)

    Abdul Gani Haji

    2013-10-01

    Full Text Available The difficulties to decompose organic waste can be handled naturally by pyrolisis so it can  decomposes quickly that produces charcoal as the product. This study aims to investigate the characteristics of activated carbon from urban organic waste. Charcoal results of pyrolysis of organic waste activated with KOH 1.0 M at a temperature of 700 and 800oC for 60 to 120 minutes. Characteristics of activated carbon were identified by Furrier Transform Infra Red (FTIR, Scanning Electron Microscopy (SEM, and X-Ray Diffraction (XRD. However, their quality is determined yield, moisture content, ash, fly substances, fixed carbon, and the power of adsorption of iodine and benzene. The identified functional groups on activated carbon, such as OH (3448,5-3436,9 cm-1, and C=O (1639,4 cm-1. In general, the degree and distance between the layers of active carbon crystallites produced activation in all treatments showed no significant difference. The pattern of activated carbon surface topography structure shows that the greater the pore formation in accordance with the temperature increase the more activation time needed. The yield of activated carbon obtained ranged from 72.04 to 82.75%. The results of characterization properties of activated carbon was obtained from 1.11 to 5.41% water, 13.68 to 17.27% substance fly, 20.36 to 26.59% ash, and 56.14 to 62.31% of fixed carbon . Absorption of activated carbon was good enough at 800oC and 120 minutes of activation time, that was equal to 409.52 mg/g of iodine and 14.03% of benzene. Activated carbon produced has less good quality, because only the water content and flying substances that meet the standards.Doi: 10.12777/ijse.5.2.89-94 [How to cite this article: Haji, A.G., Pari, G., Nazar, M., and Habibati.  (2013. Characterization of activated carbon produced from urban organic waste . International Journal of Science and Engineering, 5(2,89-94. Doi: 10.12777/ijse.5.2.89-94

  10. Assessment of produced water contaminated soils to determine remediation requirements

    International Nuclear Information System (INIS)

    Clodfelter, C.

    1995-01-01

    Produced water and drilling fluids can impact the agricultural properties of soil and result in potential regulatory and legal liabilities. Produced water typically is classified as saline or a brine and affects surface soils by increasing the sodium and chloride content. Sources of produced water which can lead to problems include spills from flowlines and tank batteries, permitted surface water discharges and pit areas, particularly the larger pits including reserve pits, emergency pits and saltwater disposal pits. Methods to assess produced water spills include soil sampling with various chemical analyses and surface geophysical methods. A variety of laboratory analytical methods are available for soil assessment which include electrical conductivity, sodium adsorption ratio, cation exchange capacity, exchangeable sodium percent and others. Limiting the list of analytical parameters to reduce cost and still obtain the data necessary to assess the extent of contamination and determine remediation requirements can be difficult. The advantage to using analytical techniques is that often regulatory remediation standards are tied to soil properties determined from laboratory analysis. Surface geophysical techniques can be an inexpensive method to rapidly determine the extent and relative magnitude of saline soils. Data interpretations can also provide an indication of the horizontal as well as the vertical extent of impacted soils. The following discussion focuses on produced water spills on soil and assessment of the impacted soil. Produced water typically contains dissolved hydrocarbons which are not addressed in this discussion

  11. The Effect of Surfactant Content over Cu-Ni Coatings Electroplated by the sc-CO₂ Technique.

    Science.gov (United States)

    Chuang, Ho-Chiao; Sánchez, Jorge; Cheng, Hsiang-Yun

    2017-04-19

    Co-plating of Cu-Ni coatings by supercritical CO₂ (sc-CO₂) and conventional electroplating processes was studied in this work. 1,4-butynediol was chosen as the surfactant and the effects of adjusting the surfactant content were described. Although the sc-CO₂ process displayed lower current efficiency, it effectively removed excess hydrogen that causes defects on the coating surface, refined grain size, reduced surface roughness, and increased electrochemical resistance. Surface roughness of coatings fabricated by the sc-CO₂ process was reduced by an average of 10%, and a maximum of 55%, compared to conventional process at different fabrication parameters. Cu-Ni coatings produced by the sc-CO₂ process displayed increased corrosion potential of ~0.05 V over Cu-Ni coatings produced by the conventional process, and 0.175 V over pure Cu coatings produced by the conventional process. For coatings ~10 µm thick, internal stress developed from the sc-CO₂ process were ~20 MPa lower than conventional process. Finally, the preferred crystal orientation of the fabricated coatings remained in the (111) direction regardless of the process used or surfactant content.

  12. List of Content

    Directory of Open Access Journals (Sweden)

    IJRED Editorial

    2013-02-01

    Full Text Available CONTENTS OF ARTICLES PAGEPassive Design of Buildings for Extreme Weather EnvironmentS.N. Al-Zubaidy, S. Tokbolat, R. Tokpatayeva 1-11 Economic Impact of CDM Implementation through Alternate Energy Resource SubstitutionK.J. Sreekanth, S. Jayaraj, N. Sudarsan 13-18 Implications of Charcoal Briquette Produced by Local Communities on Livelihoods and Environment in Nairobi KenyaMary Njenga, A Yonemitsu, N Karanjaa, M Iiyama, J Kithinji, M Dubbeling C Sundberge, R R Jamnadass 19-29 A Novel Design of Multi-Chambered Biomass BatteryK. Sudhakar, R. Ananthakrishnan, A. Goyal, H.K. Darji 31-34 Power Quality Improvement Wind Energy System Using Cascaded Multilevel InverterJ.S. Sathiyanarayanan, A. S. Kumar 35-43 Solar PV Lighting and Studying after Sunset: Analysis of Micro-benefits in Off-grid Rural GhanaGeorge Y. Obeng 45-51 Innovative Green Technology for Sustainable Industrial Estate DevelopmentR. Hadiwijoyo, P Purwanto, Sudharto P Hadi 53-58 Empowering Distributed Solar PV Energy For Malaysian Rural Housing: Towards Energy Security And Equitability Of Rural CommunitiesN.A. Ahmad, H. Byrd 59-68

  13. A novel method to produce dry geopolymer cement powder

    Directory of Open Access Journals (Sweden)

    H.A. Abdel-Gawwad

    2016-04-01

    Full Text Available Geopolymer cement is the result of reaction of two materials containing aluminosilicate and concentrated alkaline solution to produce an inorganic polymer binder. The alkali solutions are corrosive and often viscous solutions which are not user friendly, and would be difficult to use for bulk production. This work aims to produce one-mix geopolymer mixed water that could be an alternative to Portland cement by blending with dry activator. Sodium hydroxide (SH was dissolved in water and added to calcium carbonate (CC then dried at 80 °C for 8 h followed by pulverization to a fixed particle size to produce the dry activator consisting of calcium hydroxide (CH, sodium carbonate (SC and pirssonite (P. This increases their commercial availability. The dry activator was blended with granulated blast-furnace slag (GBFS to produce geopolymer cement powder and by addition of water; the geopolymerization process is started. The effect of W/C and SH/CC ratio on the physico-mechanical properties of slag pastes was studied. The results showed that the optimum percent of activator and CC content is 4% SH and 5% CC, by the weight of slag, which give the highest physico-mechanical properties of GBFS. The characterization of the activated slag pastes was carried out using TGA, DTG, IR spectroscopy and SEM techniques.

  14. Non-Invasive Rapid Harvest Time Determination of Oil-Producing Microalgae Cultivations for Biodiesel Production by Using Chlorophyll Fluorescence

    Energy Technology Data Exchange (ETDEWEB)

    Qiao, Yaqin [Key Laboratory of Algal Biology, Institute of Hydrobiology, Chinese Academy of Sciences, Wuhan (China); University of Chinese Academy of Sciences, Beijing (China); Rong, Junfeng [SINOPEC Research Institute of Petroleum Processing, Beijing (China); Chen, Hui; He, Chenliu; Wang, Qiang, E-mail: wangqiang@ihb.ac.cn [Key Laboratory of Algal Biology, Institute of Hydrobiology, Chinese Academy of Sciences, Wuhan (China)

    2015-10-05

    For the large-scale cultivation of microalgae for biodiesel production, one of the key problems is the determination of the optimum time for algal harvest when algae cells are saturated with neutral lipids. In this study, a method to determine the optimum harvest time in oil-producing microalgal cultivations by measuring the maximum photochemical efficiency of photosystem II, also called Fv/Fm, was established. When oil-producing Chlorella strains were cultivated and then treated with nitrogen starvation, it not only stimulated neutral lipid accumulation, but also affected the photosynthesis system, with the neutral lipid contents in all four algae strains – Chlorella sorokiniana C1, Chlorella sp. C2, C. sorokiniana C3, and C. sorokiniana C7 – correlating negatively with the Fv/Fm values. Thus, for the given oil-producing algae, in which a significant relationship between the neutral lipid content and Fv/Fm value under nutrient stress can be established, the optimum harvest time can be determined by measuring the value of Fv/Fm. It is hoped that this method can provide an efficient way to determine the harvest time rapidly and expediently in large-scale oil-producing microalgae cultivations for biodiesel production.

  15. Selenium contents of Japanese foodstuffs by neutron activation analysis

    International Nuclear Information System (INIS)

    Noda, Katsuhiko; Hirai, Shoji; Danbara, Hiroshi.

    1980-01-01

    Selenium (Se) contents of Japanese foodstuffs were measured by neutron activation analyses with the TRIGA-II reactor in Atomic Energy Research Laboratory, Musashi Institute of Technology. Freezedried samples (200 - 500 mg) were irradiated in the pneumatic tube (thermal neutron flux, 1 x 10 12 n.cm -2 . sec -1 ) for 10 sec, and sup(77m)Se produced was counted for 30 sec in a gamma -ray spectrometer system equipped with a Ge(Li) detector. Samples containing less than 0.05 ppm Se and the processed foods of high salt contents were analyzed with radioactivities of 75 Se after irradiation in the central symble (thermal neutron flux, 4 x 10 12 n.cm -2 .sec -1 ) for 5 hours, digestion in the HNO 3 -HClO 4 mixture, and then purification by a precipitation process. Foodstuffs of animal origins contained more Se than those of plant origins. Se contents were as follows in the descending order: fish, meats, cereals, vegetables, and fruit. Daily per capital intaked of Se was in the range of 100 - 200 mu g, as calculated for and as found by analysis of composite diets representing ordinary Japanese meals. (author)

  16. Technical note - the incorporation of ash content into gas content

    Energy Technology Data Exchange (ETDEWEB)

    Creech, M.; Mahoney, M. [Powercoal Pty. Ltd., Budgewoi, NSW (Australia)

    1995-12-31

    For gas content analysis in recent years, it has been standard procedure to report results on a `dry ash free` (daf) basis, under the assumption that gas only adsorbs onto coaly material. In order to test the relationship between ash and gas content, samples of various rock types were taken from two drillholes in the Newcastle Coalfield. The results of this study confirmed the correlation between gas content and ash, providing an accurate means of relating gas contents for all carbonaceous rock types. 4 refs., 5 figs., 1 tab.

  17. Integrating personalized medical test contents with XML and XSL-FO.

    Science.gov (United States)

    Toddenroth, Dennis; Dugas, Martin; Frankewitsch, Thomas

    2011-03-01

    In 2004 the adoption of a modular curriculum at the medical faculty in Muenster led to the introduction of centralized examinations based on multiple-choice questions (MCQs). We report on how organizational challenges of realizing faculty-wide personalized tests were addressed by implementation of a specialized software module to automatically generate test sheets from individual test registrations and MCQ contents. Key steps of the presented method for preparing personalized test sheets are (1) the compilation of relevant item contents and graphical media from a relational database with database queries, (2) the creation of Extensible Markup Language (XML) intermediates, and (3) the transformation into paginated documents. The software module by use of an open source print formatter consistently produced high-quality test sheets, while the blending of vectorized textual contents and pixel graphics resulted in efficient output file sizes. Concomitantly the module permitted an individual randomization of item sequences to prevent illicit collusion. The automatic generation of personalized MCQ test sheets is feasible using freely available open source software libraries, and can be efficiently deployed on a faculty-wide scale.

  18. Carbon films produced from ionic liquid carbon precursors

    Science.gov (United States)

    Dai, Sheng; Luo, Huimin; Lee, Je Seung

    2013-11-05

    The invention is directed to a method for producing a film of porous carbon, the method comprising carbonizing a film of an ionic liquid, wherein the ionic liquid has the general formula (X.sup.+a).sub.x(Y.sup.-b).sub.y, wherein the variables a and b are, independently, non-zero integers, and the subscript variables x and y are, independently, non-zero integers, such that ax=by, and at least one of X.sup.+ and Y.sup.- possesses at least one carbon-nitrogen unsaturated bond. The invention is also directed to a composition comprising a porous carbon film possessing a nitrogen content of at least 10 atom %.

  19. [Relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii].

    Science.gov (United States)

    Zhu, Hua; Teng, Jianbei; Cai, Yi; Liang, Jie; Zhu, Yilin; Wei, Tao

    2011-12-01

    To find out the relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii. Microscopy-counting process was applied to starch quantity statistics, sulfuric acid-anthrone colorimetry was used to assay polysaccharides content and bromocresol green colorimetry was used to assay alkaloid content. Pearson product moment correlation analysis, Kendall's rank correlation analysis and Spearman's concordance coefficient analysis were applied to study their relativity. Extremely significant positive correlation was found between starch quantity and polysaccharides content, and significant negative correlation between alkaloid content and starch quantity was discovered, as well was between alkaloid content and polysaccharides content.

  20. Selenium treatment differentially affects sulfur metabolism in high and low glucosinolate producing cultivars of broccoli (Brassica oleracea L.).

    Science.gov (United States)

    McKenzie, Marian J; Chen, Ronan K Y; Leung, Susanna; Joshi, Srishti; Rippon, Paula E; Joyce, Nigel I; McManus, Michael T

    2017-12-01

    The effect of selenium (Se) application on the sulfur (S)-rich glucosinolate (GSL)-containing plant, broccoli (Brassica oleracea L. var. italica) was examined with a view to producing germplasm with increased Se and GSL content for human health, and to understanding the influence of Se on the regulation of GSL production. Two cultivars differing in GSL content were compared. Increased Se application resulted in an increase in Se uptake in planta, but no significant change in total S or total GSL content in either cultivar. Also no significant change was observed in the activity of ATP sulfurylase (ATPS, EC 2.7.7.4) or O-acetylserine(thiol) lyase (OASTL, EC 2.5.1.47) with increased Se application. However, in the first investigation of APS kinase (APSK, EC 2.7.1.25) expression in response to Se fertilisation, an increase in transcript abundance of one variant of APS kinase 1 (BoAPSK1A) was observed in both cultivars, and an increase in BoAPSK2 transcript abundance was observed in the low GSL producing cultivar. A mechanism by which increased APSK transcription may provide a means of controlling the content of S-containing compounds, including GSLs, following Se uptake is proposed. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  1. Effect of gamma radiation on growth, productivity and protein content of chlorella pyrenoidosa

    International Nuclear Information System (INIS)

    Fernandez Gonzalez, J.; Martin Moreno, C.

    1983-01-01

    The effect of five doses of gamma radiation: 10, 100, 500, 1000 and 5000 Gy at a dose rate of 4.500 Gy/h on growth, productivity and protein content of Chlorella Pyroneidosa has been studied. High doses of gamma radiation have been observed to inhibit cellular division of Chlorella Pyrenoidosa. Culture growth stopped 48 hours after irradiation at 5.000 Gy and 72 hours after irradiation at 500 and 1000 Gy. The lowest dose (10 Gy) produced a little growth stimulation that as not statistically significative. Protein and aminoacid content did not show any change for gamma radiation doses studied. (author)

  2. Effect of gamma radiation on growth, productivity and protein content of Chlorella Pyrenoidosa

    International Nuclear Information System (INIS)

    Martin Moreno, C.; Fernandez Gonzalez, J.

    1983-01-01

    The effect of five doses of gamma radiation: 10, 100, 500, 1000 and 5000 Gy at a dose rate of 4.500 Gy/h on growth, productivity and protein content of Chlorella pyroneidosa has been studied. High doses of gamma radiation have been observed to inhibit cellular division of Chlorella pyrenoidosa. Culture growth stopped 48 hours after irradiation at 5.000 Gy and 72 hours after irradiation at 500 and 1000 Gy. The lowest dose (10 Gyl produced a little growth stimulation that not statistically significative. Protein and aminoacid content did not show any change for gamma radiation doses studied. (Author) 32 refs

  3. Analysis of total hydrogen content in palm oil and palm kernel oil ...

    African Journals Online (AJOL)

    A fast and non-destructive technique based on thermal neutron moderation has been used for determining the total hydrogen content in two types of red palm oil (dzomi and amidze) and palm kernel oil produced by traditio-nal methods in Ghana. An equipment consisting of an 241Am-Be neutron source and 3He neutron ...

  4. Adolescent judgment of sexual content on television: implications for future content analysis research.

    Science.gov (United States)

    Manganello, Jennifer A; Henderson, Vani R; Jordan, Amy; Trentacoste, Nicole; Martin, Suzanne; Hennessy, Michael; Fishbein, Martin

    2010-07-01

    Many studies of sexual messages in media utilize content analysis methods. At times, this research assumes that researchers and trained coders using content analysis methods and the intended audience view and interpret media content similarly. This article compares adolescents' perceptions of the presence or absence of sexual content on television to those of researchers using three different coding schemes. Results from this formative research study suggest that participants and researchers are most likely to agree with content categories assessing manifest content, and that differences exist among adolescents who view sexual messages on television. Researchers using content analysis methods to examine sexual content in media and media effects on sexual behavior should consider identifying how audience characteristics may affect interpretation of content and account for audience perspectives in content analysis study protocols when appropriate for study goals.

  5. Thermal decomposition of supported lithium nitrate catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz, Maria Lucia [INTEQUI (CONICET-UNSL), 25 de Mayo 384, V. Mercedes, 5730, San Luis (Argentina); Lick, Ileana Daniela [CINDECA (CONICET-UNLP), Calle 47 No 257, La Plata, 1900, Buenos Aires (Argentina); Ponzi, Marta Isabel [INTEQUI (CONICET-UNSL), 25 de Mayo 384, V. Mercedes, 5730, San Luis (Argentina); Castellon, Enrique Rodriguez; Jimenez-Lopez, Antonio [Departamento de Quimica Inorganica, Cristalografia y Mineralogia. Facultad de Ciencias, Universidad de Malaga, Campus de Teatinos, 29071 Malaga (Spain); Ponzi, Esther Natalia, E-mail: eponzi@quimica.unlp.edu.ar [CINDECA (CONICET-UNLP), Calle 47 No 257, La Plata, 1900, Buenos Aires (Argentina)

    2010-02-20

    New catalysts for soot combustion were prepared by impregnation of different supports (SiO{sub 2}, ZrO{sub 2} and ZrO{sub 2}.nH{sub 2}O) with a LiNO{sub 3} solution and then characterized by means of FTIR, XPS, TGA and UV-vis spectroscopy, whereby the presence of lithium nitrate in the prepared catalysts was identified and quantified. The soot combustion rate using this series of catalysts (LiNO{sub 3}/support) was compared with the activity of a series of impregnated catalysts prepared using LiOH (Li{sub 2}O/supports). Catalysts prepared using LiNO{sub 3} are found to be more active than those prepared using LiOH. The catalytic performance was also studied with a NO/O{sub 2} mixture in the feed, demonstrating that NO increases the combustion rate of soot, probably as a consequence of lithium oxide forming an 'in situ' nitrate ion.

  6. [Effects of nitrogen application rate on nitrate reductase activity, nitric oxide content and gas exchange in winter wheat leaves].

    Science.gov (United States)

    Shangguan, Zhou-Ping

    2007-07-01

    In this paper, the effects of different nitrogen application rates on the nitrate reductase (NR) activity, nitric oxide (NO) content and gas exchange parameters in winter wheat (Triticum aestivum L.) leaves from tillering stage to heading stage and on grain yield were studied. The results showed that the photosynthetic rate (P(n)), transpiration rate (T(r)) and instantaneous water use efficiency (IWUE) of leaves as well as the grain yield were increased with increasing nitrogen application rate first but decreased then, with the values of all these parameters reached the highest in treatment N180. The NR activity increased with increasing nitrogen application rate, and there was a significant linear correlation between NR activity and NO content at tillering and jointing stages (R2 > or = 0.68, n = 15). NO content had a quadratic positive correlation with stomatal conductance (G(s)) (R2 > or = 0.43, n = 15). The lower NO content produced by lower NR activity under lower nitrogen application rate promoted the stoma opened, while the higher NO content produced by higher NR activity under higher nitrogen application rate induced the stoma closed. Although the leaf NO content had a quadratic positive correlation with stomatal conductance (R2 > or = 0.36, n = 15), no remarkable correlation was observed between NR activity and NO content at heading stage, suggesting that nitrogen fertilization could not affect leaf NO content through promoting NR activity, and further more, regulate the stomatal action. Under appropriate nitrogen application the leaf NR activity and NO content were lower, G(s), T(r) and IWUE were higher, and thus, the crop had a better drought-resistant ability, higher P(n), and higher grain yield.

  7. Improving the Organoleptic Properties of a Craft Mezcal Beverage by Increasing Fatty Acid Ethyl Ester Contents through ATF1 Expression in an Engineered Kluyveromyces marxianus UMPe-1 Yeast.

    Science.gov (United States)

    Campos-García, Jesús; Vargas, Alejandra; Farías-Rosales, Lorena; Miranda, Ana L; Meza-Carmen, Víctor; Díaz-Pérez, Alma L

    2018-05-02

    Mezcal, a traditional beverage that originated in Mexico, is produced from species of the Agavaceae family. The esters associated with the yeasts utilized during fermentation are important for improving the organoleptic properties of the beverage. We improved the ester contents in a mezcal beverage by using the yeast Kluyveromyces marxianus, which was engineered with the ATF1 gene. ATF1 expression in the recombinant yeast significantly increased compared with that in the parental yeast, but its fermentative parameters were unchanged. Volatile-organic-compound-content analysis showed that esters had significantly increased in the mezcal produced with the engineered yeast. In a sensory-panel test, 48% of the panelists preferred the mezcal produced from the engineered yeast, 30% preferred the mezcal produced from the wild type, and 15 and 7% preferred the two mezcal types produced following the routine procedure. Correlation analysis showed that the fruitiness/sweetness description of the mezcal produced using the ATF1-engineered K. marxianus yeast correlated with the content of the esters, whose presence improved the organoleptic properties of the craft mezcal beverage.

  8. THE LYMAN ALPHA REFERENCE SAMPLE: EXTENDED LYMAN ALPHA HALOS PRODUCED AT LOW DUST CONTENT

    Energy Technology Data Exchange (ETDEWEB)

    Hayes, Matthew [Universite de Toulouse, UPS-OMP, IRAP, Toulouse (France); Oestlin, Goeran; Duval, Florent; Guaita, Lucia; Melinder, Jens; Sandberg, Andreas [Department of Astronomy, Oskar Klein Centre, Stockholm University, AlbaNova University Centre, SE-106 91 Stockholm (Sweden); Schaerer, Daniel [CNRS, IRAP, 14, avenue Edouard Belin, F-31400 Toulouse (France); Verhamme, Anne; Orlitova, Ivana [Geneva Observatory, University of Geneva, 51 Chemin des Maillettes, CH-1290 Versoix (Switzerland); Mas-Hesse, J. Miguel; Oti-Floranes, Hector [Centro de Astrobiologia (CSIC-INTA), Departamento de Astrofisica, POB 78, 28691 Villanueva de la Canada (Spain); Adamo, Angela [Max Planck Institute for Astronomy, Koenigstuhl 17, D-69117 Heidelberg (Germany); Atek, Hakim [Laboratoire d' Astrophysique, Ecole Polytechnique Federale de Lausanne (EPFL), Observatoire, CH-1290 Sauverny (Switzerland); Cannon, John M. [Department of Physics and Astronomy, Macalester College, 1600 Grand Avenue, Saint Paul, MN 55105 (United States); Herenz, E. Christian [Leibniz-Institut fuer Astrophysik (AIP), An der Sternwarte 16, D-14482 Potsdam (Germany); Kunth, Daniel [Institut d' Astrophysique de Paris, UMR 7095 CNRS and UPMC, 98 bis Bd Arago, F-75014 Paris (France); Laursen, Peter, E-mail: matthew@astro.su.se [Dark Cosmology Centre, Niels Bohr Institute, University of Copenhagen, Juliane Maries Vej 30, DK-2100 Copenhagen (Denmark)

    2013-03-10

    We report on new imaging observations of the Lyman alpha emission line (Ly{alpha}), performed with the Hubble Space Telescope, that comprise the backbone of the Lyman alpha Reference Sample. We present images of 14 starburst galaxies at redshifts 0.028 < z < 0.18 in continuum-subtracted Ly{alpha}, H{alpha}, and the far ultraviolet continuum. We show that Ly{alpha} is emitted on scales that systematically exceed those of the massive stellar population and recombination nebulae: as measured by the Petrosian 20% radius, R{sub P20}, Ly{alpha} radii are larger than those of H{alpha} by factors ranging from 1 to 3.6, with an average of 2.4. The average ratio of Ly{alpha}-to-FUV radii is 2.9. This suggests that much of the Ly{alpha} light is pushed to large radii by resonance scattering. Defining the Relative Petrosian Extension of Ly{alpha} compared to H{alpha}, {xi}{sub Ly{alpha}} = R {sup Ly{alpha}}{sub P20}/R {sup H{alpha}}{sub P20}, we find {xi}{sub Ly{alpha}} to be uncorrelated with total Ly{alpha} luminosity. However, {xi}{sub Ly{alpha}} is strongly correlated with quantities that scale with dust content, in the sense that a low dust abundance is a necessary requirement (although not the only one) in order to spread Ly{alpha} photons throughout the interstellar medium and drive a large extended Ly{alpha} halo.

  9. The effects of antioxidants on the content of polyunsaturated fatty acids in the hen's egg.

    Science.gov (United States)

    Kassab, A; Abrams, J T; Sainsbury, D W

    1979-01-01

    In experiments to see whether, in the possible interests of human health, the polyunsaturated fatty acid (PUFA) content of the chicken's egg can be increased by nutritional means, three strains of hen, light, medium, and heavy, each at the peak of lay, were first fed a basal, commercial, low-fat diet. The hens were then transferred to one of the following diets: basal + safflower oil (SO); basal + SO + butylated hydroxytoluene; or basal + SO + dl-a-toco-pheryl acetate. The diets were designated "Blank", "BHT", and "Vitamin E", respectively, the second and third containing the added antioxidants. The eggs produced were weighed, and their yolks weighed and analysed for lipid components. Additional of SO (7.5%) to the basal diet led to the PUFA content of the yolk lipids rising by 15.4% (linoleic acid, 14.1%), the magnitude of the increases being unaffected by the antioxidants. Diet "BHT" produced larger eggs and yolks than the other diets, but the proportion of yolk was the same on the three types of feed. The total cholesterol content of egg yolks was significantly affected neither by diet, nor by strain or age of hen. The implications of these results are discussed.

  10. Rapid spectrofluorometric screening of poly-hydroxyalkanoate-producing bacteria from microbial mats.

    Science.gov (United States)

    Berlanga, Mercedes; Montero, M T; Fernández-Borrell, Jordi; Guerrero, Ricardo

    2006-06-01

    Microbial mat ecosystems are characterized by both seasonal and diel fluctuations in several physicochemical variables, so that resident microorganisms must frequently adapt to the changing conditions of their environment. It has been pointed out that, under stress conditions, bacterial cells with higher contents of poly-hydroxyalkanoates (PHA) survive longer than those with lower PHA content. In the present study, PHA-producing strains from Ebro Delta microbial mats were selected using the Nile red dying technique and the relative accumulation of PHA was monitored during further laboratory cultivation. The number of heterotrophic isolates in trypticase soy agar (TSA) was ca. 107 colony-forming units/g microbial mat. Of these, 100 randomly chosen colonies were replicated on mineral salt agar limited in nitrogen, and Nile red was added to the medium to detect PHA. Orange fluorescence, produced upon binding of the dye to polymer granules in the cell, was detected in approximately 10% of the replicated heterotrophic isolates. The kinetics of PHA accumulation in Pseudomonas putida, and P. oleovorans were compared with those of several of the environmental isolates spectrofluorometry. PHA accumulation, measured as relative fluorescence intensity, resulted in a steady-state concentration after 48 h of incubation in all strains assayed. At 72 h, the maximum fluorescence intensity of each strain incubated with glucose and fructose was usually similar. MAT-28 strain accumulated more PHA than the other isolates. The results show that data obtained from environmental isolates can highly improve studies based on modeling-simulation programs, and that microbial mats constitute an excellent source for the isolation of PHA-producing strains with industrial applications.

  11. Effect of Different Elicitors and Preharvest Day Application on the Content of Phytochemicals and Antioxidant Activity of Butterhead Lettuce (Lactuca sativa var. capitata) Produced under Hydroponic Conditions.

    Science.gov (United States)

    Moreno-Escamilla, Jesús Omar; Alvarez-Parrilla, Emilio; de la Rosa, Laura A; Núñez-Gastélum, José Alberto; González-Aguilar, Gustavo A; Rodrigo-García, Joaquín

    2017-07-05

    The effect of four elicitors on phytochemical content in two varieties of lettuce was evaluated. The best preharvest day for application of each elicitor was chosen. Solutions of arachidonic acid (AA), salicylic acid (SA), methyl jasmonate (MJ), and Harpin protein (HP) were applied by foliar aspersion on lettuce leaves while cultivating under hydroponic conditions. Application of elicitors was done at 15, 7, 5, 3, or 1 day before harvest. Green lettuce showed the highest increase in phytochemical content when elicitors (AA, SA, and HP) were applied on day 7 before harvest. Similarly, antioxidant activity rose in all treatments on day 7. In red lettuce, the highest content of bioactive molecules occurred in samples treated on day 15. AA, SA, and HP were the elicitors with the highest effect on phytochemical content for both varieties, mainly on polyphenol content. Antioxidant activity also increased in response to elicitation. HPLC-MS showed an increase in the content of phenolic acids in green and red lettuce, especially after elicitation with SA, suggesting activation of the caffeic acid pathway due to elicitation.

  12. Microstructure and thermal and functional properties of biodegradable films produced using zein

    Directory of Open Access Journals (Sweden)

    Crislene Barbosa de Almeida

    2018-03-01

    Full Text Available Abstract Research is being conducted in an attempt to produce biodegradable packaging to replace plastic products, thereby reducing solid waste disposal. In this work, zein films were produced from vegetable oils (macadamia, olive and buriti and from pure oleic acid. The surface of zein-based films made using oleic acid has a good lipid distribution. The high content of oleic acid produced a film with the greatest elongation at break (8.08 ± 2.71% due to the greater homogeneity of the protein matrix. The different oils did not affect the glass transition temperature (Tg. Tg curves of films with fatty acids showed a reduction in mass at between 50 and 120 °C due to water evaporation. At 120 °C the weight loss was 3-5% and above this temperature further weight loss was observed with the highest loss being seen in the film made using pure oleic acid. In conclusion, although biodegradable films were produced using the four different oils, the film made from pure oleic acid has the best characteristics.

  13. Microstructure and Mechanical Properties of Al-10Zn-4.5Mg-xCu Turbine Impeller Produced by Investment Casting

    Directory of Open Access Journals (Sweden)

    Muhammad Syahid

    2017-03-01

    Full Text Available Aluminium alloy can be applied for a turbine impeller of Organic Rankine Cycle power plant that operates at temperatures below 150 oC. Aluminum turbine impeller can enhance efficiency of turbine due to light weight material. Al alloys was used for impeller due to good mechanical properties. Turbine impeller commonly produced by machining but which is time-consuming and less efficient because of material removal. . It can be replace by Investment casting to produce impeller turbine due to their complex geometry and precision. This study identifies effect Cu content of Al-9Zn-4Mg-xCu on the microstructure and mechanical properties of turbine impeller produce by investment casting. The study also identifies casting defect of turbine impeller. The structures consisted of α-Al, MgZn2, CuMgAl2 and CuAl2. Higher Cu content is the higher hardness value due to CuAl2 phase. Visual examination showed that the turbine impeller was free of macro defects and misruns

  14. A method for producing a hydrocarbon resin

    Energy Technology Data Exchange (ETDEWEB)

    Tsachev, A B; Andonov, K S; Igliyev, S P

    1980-11-25

    Rock coal resin (KS), for instance, with a relative density of 1,150 to 1,190 kilograms per cubic meter, which contains 8 to 10 percent naphthaline, 1.5 to 2.8 percent phenol and 6 to 15 percent substances insoluble in toluene, or its mixture with rock coal or oil fractions of resin are subjected to distillation (Ds) in a pipe furnace with two evaporators (Is) and a distillation tower with a temperature mode in the second stage of 320 to 360 degrees and 290 to 340 degrees in the pitch compartment. A hydrocarbon resin is produced with a high carbon content, especially for the production of resin and dolomite refractory materials, as well as fuel mixtures for blast furnace and open hearth industry.

  15. Determination of Optimum Condition of Leucine Content in Beef Protein Hydrolysate using Response Surface Methodology

    International Nuclear Information System (INIS)

    Siti Roha Ab Mutalib; Zainal Samicho; Noriham Abdullah

    2016-01-01

    The aim of this study is to determine the optimum condition of leucine content in beef hydrolysate. Beef hydrolysate was prepared by enzymatic hydrolysis using bromelain enzyme produced from pineapple peel. Parameter conditions such as concentration of bromelain, hydrolysis temperature and hydrolysis time were assessed to obtain the optimum leucine content of beef hydrolysate according to experimental design which was recommended by response surface methodology (RSM). Leucine content in beef hydrolysate was determined using AccQ. Tag amino acid analysis method using high performance liquid chromatography (HPLC). The condition of optimum leucine content was at bromelain concentration of 1.38 %, hydrolysis temperature of 42.5 degree Celcius and hydrolysis time of 31.59 hours with the predicted leucine content of 26.57 %. The optimum condition was verified with the leucine value obtained was 26.25 %. Since there was no significant difference (p>0.05) between the predicted and verified leucine values, thus it indicates that the predicted optimum condition by RSM can be accepted to predict the optimum leucine content in beef hydrolysate. (author)

  16. A review of content-based image retrieval systems in medical applications-clinical benefits and future directions.

    Science.gov (United States)

    Müller, Henning; Michoux, Nicolas; Bandon, David; Geissbuhler, Antoine

    2004-02-01

    Content-based visual information retrieval (CBVIR) or content-based image retrieval (CBIR) has been one on the most vivid research areas in the field of computer vision over the last 10 years. The availability of large and steadily growing amounts of visual and multimedia data, and the development of the Internet underline the need to create thematic access methods that offer more than simple text-based queries or requests based on matching exact database fields. Many programs and tools have been developed to formulate and execute queries based on the visual or audio content and to help browsing large multimedia repositories. Still, no general breakthrough has been achieved with respect to large varied databases with documents of differing sorts and with varying characteristics. Answers to many questions with respect to speed, semantic descriptors or objective image interpretations are still unanswered. In the medical field, images, and especially digital images, are produced in ever-increasing quantities and used for diagnostics and therapy. The Radiology Department of the University Hospital of Geneva alone produced more than 12,000 images a day in 2002. The cardiology is currently the second largest producer of digital images, especially with videos of cardiac catheterization ( approximately 1800 exams per year containing almost 2000 images each). The total amount of cardiologic image data produced in the Geneva University Hospital was around 1 TB in 2002. Endoscopic videos can equally produce enormous amounts of data. With digital imaging and communications in medicine (DICOM), a standard for image communication has been set and patient information can be stored with the actual image(s), although still a few problems prevail with respect to the standardization. In several articles, content-based access to medical images for supporting clinical decision-making has been proposed that would ease the management of clinical data and scenarios for the integration of

  17. Content Interactivity: The Effect of Higher Levels of Interactivity on Learner Performance Outcomes and Satisfaction in Web-Based Military Training

    Science.gov (United States)

    Kenyon, Peggy L.

    2012-01-01

    The effect of content interactivity on performance outcomes and satisfaction has been studied by researchers who compared the results of Web-based and computer-based learning to classroom learning. Few scholars have compared the effects of the same content produced at different levels (low and high) of interactivity and the resulting effects. The…

  18. Examination of dexamethasone sodium sulfate and hyperbaric oxygenation in experimentally produced cerebral edema. With special reference to their combination

    Energy Technology Data Exchange (ETDEWEB)

    Kanaya, H; Onodera, H; Watanabe, M; Kamata, K [Iwate Medical Coll., Morioka (Japan). School of Medicine

    1975-06-01

    Dexamethasone sodium sulfate and hyperbaric oxygenation were used for experimentally produced cerebral edema for the examination of the water content of the brain and cerebrovascular permeability using /sup 203/Hg as the tracer. Although dexamethasone starts lowering vascular permeability of the edematous brain at one hour after the intravenous injection, a lapse of 24 hours is required until the water content returns to normal. Although hyperbaric oxygenation dose not reduce cerebrovascular permeability, it brings back the water content of the brain to normal immediately after pressurization. Since the combination of dexamethasone and hyperbaric oxygenation maintains the water content of the brain almost normal throughout the entire process, it is ideal for the treatment of cerebral edema.

  19. Nanoemulsions produced with varied type of emulsifier and oil content: An influence of formulation and process parameters on the characteristics and physical stability

    Directory of Open Access Journals (Sweden)

    Đorđević Sanela M.

    2013-01-01

    Full Text Available The aim of the present study was to prepare oil-in-water nanoemulsions stabilized with a novel natural alkyl polyglucoside surfactant and to compare them with corresponding lecithin/polysorbate 80 - based nanoemulsions in terms of physicochemical properties and physical stability. Nanoemulsions were prepared by high pressure homogenization, using 20, 30 and 40% (w/w medium chain triglyceride as oil phase, and 4, 6 and 8% (w/w lecithin/polysorbate 80 mixture (1/1 or caprylyl/capryl glucoside as emulsifiers. The influence of emulsifier type, emulsifier concentration and oil content was investigated with respect to changes in particle size, particle size distribution, surface charge and physical stability. The influence of production parameters (number of homogenization cycles, type of homogenization process, homogenization pressure on particle size was also investigated. Analysis was performed by photon correlation spectroscopy, laser diffraction, zeta potential, pH and electrical conductivity measurements. All formulations produced revealed a small droplet size ranging from 147 to 228 nm and a very narrow size distribution (polydispersity index range 0,072-0,124. Zeta potentials were about -20 mV and -50 mV for nanoemulsions stabilized with lecithin/polysorbate 80 and caprylyl/capryl glucoside, respectively. The results obtained during the stability studies (6 months at 25°C and 1 month at 40°C indicated that nanoemulsion stability was influenced by their composition. Acquired results also suggested the most appropriate production parameters: 9 homogenization cycles, homogenization pressure of 500 bar and discontinuous process of homogenization.

  20. Results and Conclusions from the NASA Isokinetic Total Water Content Probe 2009 IRT Test

    Science.gov (United States)

    Reehorst, Andrew; Brinker, David

    2010-01-01

    The NASA Glenn Research Center has developed and tested a Total Water Content Isokinetic Sampling Probe. Since, by its nature, it is not sensitive to cloud water particle phase nor size, it is particularly attractive to support super-cooled large droplet and high ice water content aircraft icing studies. The instrument comprises the Sampling Probe, Sample Flow Control, and Water Vapor Measurement subsystems. Results and conclusions are presented from probe tests in the NASA Glenn Icing Research Tunnel (IRT) during January and February 2009. The use of reference probe heat and the control of air pressure in the water vapor measurement subsystem are discussed. Several run-time error sources were found to produce identifiable signatures that are presented and discussed. Some of the differences between measured Isokinetic Total Water Content Probe and IRT calibration seems to be caused by tunnel humidification and moisture/ice crystal blow around. Droplet size, airspeed, and liquid water content effects also appear to be present in the IRT calibration. Based upon test results, the authors provide recommendations for future Isokinetic Total Water Content Probe development.

  1. Optimizing the process of making sweet wines to minimize the content of ochratoxin A.

    Science.gov (United States)

    Ruíz Bejarano, M Jesús; Rodríguez Dodero, M Carmen; García Barroso, Carmelo

    2010-12-22

    During the drying process of raisins, the grapes are subjected to climatic variations that can result in heavy infections of some fungal species that produce ochratoxin A (OTA), a powerful toxic metabolite, whose maximum permitted content is set by the European Union at 2.0 μg/L for grapes, wine and other drinks derived from the grape. The aim of this paper is to optimize the process of making sweet wines in order to minimize the content of ochratoxin A. The results reflect a reduction of the OTA content in grapes dried under controlled conditions in a climatic chamber up to 24% compared to those sunned in the traditional way. A decrease of the concentrations of OTA is also observed during the processes of vinification. Those wines with prefermentative maceration reached a higher OTA content than the wines without maceration, but unexpectedly were not those preferred from a sensorial point of view. In addition, the process of aging in oak casks has been shown to serve as a natural method for reducing the OTA content of these wines.

  2. Evaluation of membranes for the treatment of oilfield-produced water

    Directory of Open Access Journals (Sweden)

    Silvio Edegar Weschenfelder

    2015-04-01

    Full Text Available Large quantities of water are generated during oil extraction. Reinjection of this effluent is frequently the most suitable option for environmental considerations. For this purpose, the water produced must have characteristics that will prevent the plugging of the reservoir rocks, i.e., suspended solids and oil and grease content must be lower than 5 mg L-1. This work evaluated the performance of membranes for water treatment, based upon long-term experiments with real effluent, evaluating the permeate flux over time and the effluent characteristics. The results indicated that it is possible to obtain a permeate flux with suspended solids content with less than 1 mg L-1 oil and a grease concentration in the range of 1 to 3 mg L-1 using membranes with a pore size of 0,1 m. After 50 hours of permeation, the permeate fluxes obtained with the polymeric and ceramic membranes were equal to 50 and 300 L h-1 m-2, respectively. With a chemical regeneration procedure, it was possible to recover 95% of the ceramic membrane’s original permeability and 30% of the polymeric membrane’s permeability. Considering the permeate quality, the regeneration efficiency of the membrane and the fluxes achieved, it is possible to point out the use of ceramic membranes as a potential technology for treating oilfield-produced water, and it has the advantage of being a compact and robust process.

  3. Determination of oxygen content in high T/sub c/ superconductors by a charged particle activation method

    International Nuclear Information System (INIS)

    Tao, Z.; Alburger, D.E.; Jones, K.W.; Yao, Y.D.; Kao, Y.H.

    1988-01-01

    A new method for determining the oxygen content in high T/sub c/ superconductors has been demonstrated using a charged particle activation technique. This method allows a measurement of the concentration of 16 O atoms in the superconducting material by detection of the 17 F produced with the 16 O(d,n) 17 F nuclear reaction. By way of example, this technique is applied to the determination of oxygen content in a series of high T/sub c/ Y-Ba-Cu-O samples in which the stoichiometry is varied by reducing the copper concentration. The stabilized oxygen content shows a nonlinear dependence on the copper deficiency in these specimens

  4. Lithium extraction from orthorhombic lithium manganese oxide and the phase-transformation to spinel

    CSIR Research Space (South Africa)

    Gummow, RJ

    1993-12-01

    Full Text Available Orthorhombic LiMnO2 products, synthesised by the reaction of gamma-MnO2 and LiOH in argon at 600-620 degrees C using carbon as a reducing agent, have been evaluated as electrode materials in lithium cells. Products that contained a minor proportion...

  5. Imidazole, a New Tunable Reagent for Producing Nanocellulose, Part I: Xylan-Coated CNCs and CNFs

    Directory of Open Access Journals (Sweden)

    Jia Mao

    2017-09-01

    Full Text Available Imidazole is reported to be an effective reactant for the production of nanocellulose from hardwood pulp. The morphologies and surface properties of the nanocellulose can be simply tailored according to the water content in the imidazole system: with pure imidazole, cellulose nanofibrils (CNFs in a yield of 10 wt % can be produced. With 25 wt % of water in imidazole, cellulose nanocrystals (CNCs are obtained in 20 wt % yield. Both nanocelluloses exhibit crystallinity indices in the order of 70%. Interestingly, they retain the original xylan from the pulp with ca. 9–10 wt % of residual xylan content.

  6. Local Content

    CSIR Research Space (South Africa)

    Gibberd, Jeremy

    2016-10-01

    Full Text Available Local content refers to materials and products made in a country as opposed those that are imported. There is an increasing interest in the concept of local content as a means of supporting local economies and providing jobs (Belderbos & Sleuwaegen...

  7. The impacts of temperature, alcoholic degree and amino acids content on biogenic amines and their precursor amino acids content in red wine.

    Science.gov (United States)

    Lorenzo, C; Bordiga, M; Pérez-Álvarez, E P; Travaglia, F; Arlorio, M; Salinas, M R; Coïsson, J D; Garde-Cerdán, T

    2017-09-01

    The aim was to study how factors such as temperature, alcoholic degree, and amino acids supplementation are able to influence the content of tyramine, histamine, 2-phenylethylamine, tryptamine and their precursor amino acids in winemaking process. Biogenic amines and amino acids were quantified at the beginning, middle and end of alcoholic fermentation, and at the end of malolactic fermentation. In general, samples produced with amino acid supplementation did not show the highest concentrations of biogenic amines, except for histamine, which content increased with the addition of the four amino acids. The synthesis of tyramine was mainly affected by the temperature and alcoholic degree, the formation of phenylethylamine was largely influenced by alcoholic degree, and tryptamine synthesis principally depended on temperature. Interestingly, there was interaction between these three factors for the biogenic amines studied. In conclusion, winemaking conditions should be established depending on the biogenic amine which synthesis is required to be controlled. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Ultrasonographic Quantification of Fat Content in Fatty Liver Phantoms

    International Nuclear Information System (INIS)

    Kim, Il Young; Kim, Pyo Nyun; Joo, Gyung Soo; Kim, Ho Jung; Kim, Young Beom; Lee, Byoung Ho

    1995-01-01

    Assuming that the fat content of certain tissue might be quantified by measurirrg the ultrasound echo level, we analyzed the ultrasound histograms obtained from the fatty liver phantoms that contained various amount of fat. Various amount of margarine(Mazola. Cliff wood. USA) was mixed with 2% of agarin solution state to produce fatty liver phantoms that contained 5, 10, 20, 30 and 40% of fat. We obtained ultrasound histogram from each fatty liver phantom in gel state. We used 2% agar gel as a control. The ultrasound histograms from the control phantom showed gradual increase in echo level as the depth from the surface increased. The echo level from the phantom that contained 5% of fat showed gradual increase and subsequent decrease with the peak echo level at the depth of 3cm. The echo levels from the phantoms that contained more in 5% of fat gradually decreased as the depth from the surface increased; the change becoming more pronounced as the fat content of the phantom increased. The echo levels measured at the depth of 1cm were 9.3(control), 29.6(5%phantom), 3l.3 (10% phantom), 26.3 (20% phantom), l8.8 (30% phantom), and l6dB (40% phantom). Fat content of fatty phantoms can not be quantified by measuring only echo level. Simultaneous measurement of attenuation of ultrasound, which is not easy to do and not done in this study, is prerequisite to quantify fat content

  9. NM WAIDS: A PRODUCED WATER QUALITY AND INFRASTRUCTURE GIS DATABASE FOR NEW MEXICO OIL PRODUCERS

    Energy Technology Data Exchange (ETDEWEB)

    Martha Cather; Robert Lee; Ibrahim Gundiler; Andrew Sung; Naomi Davidson; Ajeet Kumar Reddy; Mingzhen Wei

    2003-04-01

    accuracy and speed of water quality data entry. (4) Acquisition of ground water data from the New Mexico State Engineer's office, including chloride content and TDS (Total Dissolved Solids) for over 30,000 data points in southeast New Mexico. (5) Creation of a web-based scale prediction tool, again with a web-based interface, that uses two common scaling indices (Stiff-Davis and Oddo-Thomson) to predict the likelihood of scaling. This prediction tool can either run from user input data, or the user can select samples from the water analysis database. (6) Creation of depth-to-groundwater maps for the study area. (7) Analysis of water quality data by formation. (8) Continuation of efforts to collect produced water quality information from operators in the southeast New Mexico area. (9) Qualitative assessment of produced water from various formations regarding corrosivity. (10) Efforts at corrosion education in the region through operator visits. Future work on this project will include: (11) Development of an integrated web and GIS interface for all the information collected in this effort. (12) Continued development of a fuzzy logic spill risk assessment tool that was initially developed prior to this project. Improvements will include addition of parameters found to be significant in determining the impact of a brine spill at a specific site. (13) Cleanup and integration of water quality databases. (14) Compilation of both hard copy and online corrosion toolkit material.

  10. NM WAIDS: A PRODUCED WATER QUALITY AND INFRASTRUCTURE GIS DATABASE FOR NEW MEXICO OIL PRODUCERS

    Energy Technology Data Exchange (ETDEWEB)

    Martha Cather; Robert Lee; Ibrahim Gundiler; Andrew Sung

    2003-09-24

    of water quality data entry. (4) Acquisition of ground water data from the New Mexico State Engineer's office, including chloride content and TDS (Total Dissolved Solids) for over 30,000 data points in southeast New Mexico. (5) Creation of a web-based scale prediction tool, again with a web-based interface, that uses two common scaling indices to predict the likelihood of scaling. This prediction tool can either run from user input data, or the user can select samples from the water analysis database. (6) Creation of depth-to-groundwater maps for the study area. (7) Analysis of water quality data by formation. (8) Continuation of efforts to collect produced water quality information from operators in the southeast New Mexico area. (9) Qualitative assessment of produced water from various formations regarding corrosivity. (10) Efforts at corrosion education in the region through operator visits. Future work on this project will include: (1) Development of an integrated web and GIS interface for all the information collected in this effort. (2) Continued development of a fuzzy logic spill risk assessment tool that was initially developed prior to this project. Improvements will include addition of parameters found to be significant in determining the impact of a brine spill at a specific site. (3) Compilation of both hard copy and online corrosion toolkit material.

  11. Technique for producing a continuous interference-free stream of Argon-41 in air

    International Nuclear Information System (INIS)

    Tseng, T.-T.; Jester, W.A.

    1984-01-01

    A monitoring system was developed for the detection of 131 I in the presence of orders of magnitude higher concentrations of radioactive noble gas. During the course of this work, a technique was developed for producing a continuous air stream of 41 Ar required for testing this concept. The 41 Ar stream is produced by the neutron activation of air using a research reactor. The 41 Ar content of the air stream can be varied by many orders of magnitude by varying the reactor power level and the rate at which the air is pumped through a vertically positioned tube in or in front of the reactor. It was found that the neutrons also activate other air constituents, producing undesirable interference radionuclides. Selective filtering techniques have therefore been developed to remove these interference radionuclides from the 41 Ar air stream

  12. Aluminum-graphite composite produced by mechanical milling and hot extrusion

    International Nuclear Information System (INIS)

    Flores-Zamora, M.I.; Estrada-Guel, I.; Gonzalez-Hernandez, J.; Miki-Yoshida, M.; Martinez-Sanchez, R.

    2007-01-01

    Aluminum-graphite composites were produced by mechanical milling followed by hot extrusion. Graphite content was varied between 0 and 1 wt.%. Al-graphite mixtures were initially mixed in a shaker mill without ball, followed by mechanical milling in a High-energy simoloyer mill for 2 h under argon atmosphere. Milled powders were subsequently pressed at ∼950 MPa for 2 min, and next sintered under vacuum for 3 h at 823 K. Finally, sintered products were held for 0.5 h at 823 K and hot extruded using indirect extrusion. Tension and compression tests were carried out to determine the yield stress and maximum stress of the materials. We found that the mechanical resistance increased as the graphite content increased. Microstructural characterization was done by transmission electron microscopy. Al-O-C nanofibers and graphite nanoparticles were observed in extruded samples by transmission electron microscopy. These nanoparticles and nanofibers seemed to be responsible of the reinforcement phenomenon

  13. Non-invasive rapid harvest time determination of oil-producing microalgae cultivations for bio-diesel production by using Chlorophyll fluorescence

    Directory of Open Access Journals (Sweden)

    Yaqin eQiao

    2015-10-01

    Full Text Available For the large-scale cultivation of microalgae for biodiesel production, one of the key problems is the determination of the optimum time for algal harvest when algae cells are saturated with neutral lipids. In this study, a method to determine the optimum harvest time in oil-producing microalgal cultivations by measuring the maximum photochemical efficiency of photosystem II (PSII, also called Fv/Fm, was established. When oil-producing Chlorella strains were cultivated and then treated with nitrogen starvation, it not only stimulated neutral lipid accumulation, but also affected the photosynthesis system, with the neutral lipid contents in all four algae strains – Chlorella sorokiniana C1, Chlorella sp. C2, C. sorokiniana C3, C. sorokiniana C7 – correlating negatively with the Fv/Fm values. Thus, for the given oil-producing algae, in which a significant relationship between the neutral lipid content and Fv/Fm value under nutrient stress can be established, the optimum harvest time can be determined by measuring the value of Fv/Fm. It is hoped that this method can provide an efficient way to determine the harvest time rapidly and expediently in large-scale oil-producing microalgae cultivations for biodiesel production.

  14. Computational Screening for Design of Optimal Coating Materials to Suppress Gas Evolution in Li-Ion Battery Cathodes.

    Science.gov (United States)

    Min, Kyoungmin; Seo, Seung-Woo; Choi, Byungjin; Park, Kwangjin; Cho, Eunseog

    2017-05-31

    Ni-rich layered oxides are attractive materials owing to their potentially high capacity for cathode applications. However, when used as cathodes in Li-ion batteries, they contain a large amount of Li residues, which degrade the electrochemical properties because they are the source of gas generation inside the battery. Here, we propose a computational approach to designing optimal coating materials that prevent gas evolution by removing residual Li from the surface of the battery cathode. To discover promising coating materials, the reactions of 16 metal phosphates (MPs) and 45 metal oxides (MOs) with the Li residues, LiOH, and Li 2 CO 3 are examined within a thermodynamic framework. A materials database is constructed according to density functional theory using a hybrid functional, and the reaction products are obtained according to the phases in thermodynamic equilibrium in the phase diagram. In addition, the gravimetric efficiency is calculated to identify coating materials that can eliminate Li residues with a minimal weight of the coating material. Overall, more MP and MO materials react with LiOH than with Li 2 CO 3 . Specifically, MPs exhibit better reactivity to both Li residues, whereas MOs react more with LiOH. The reaction products, such as Li-containing phosphates or oxides, are also obtained to identify the phases on the surface of a cathode after coating. On the basis of the Pareto-front analysis, P 2 O 5 could be an optimal material for the reaction with both Li residuals. Finally, the reactivity of the coating materials containing 3d/4d transition metal elements is better than that of materials containing other types of elements.

  15. Determination of Radioisotope Content by Measurement of Waste Package Dose Rates - 13394

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Daiane Cristini B.; Gimenes Tessaro, Ana Paula; Vicente, Roberto [Nuclear and Energy Research Institute Brazil, Radioactive Waste Management Department IPEN/GRR, Sao Paulo. SP. (Brazil)

    2013-07-01

    The objective of this communication is to report the observed correlation between the calculated air kerma rates produced by radioactive waste drums containing untreated ion-exchange resin and activated charcoal slurries with the measured radiation field of each package. Air kerma rates at different distances from the drum surface were calculated with the activity concentrations previously determined by gamma spectrometry of waste samples and the estimated mass, volume and geometry of solid and liquid phases of each waste package. The water content of each waste drum varies widely between different packages. Results will allow determining the total activity of wastes and are intended to complete the previous steps taken to characterize the radioisotope content of wastes packages. (authors)

  16. Form, Content, and Gender Differences in Lego[R] Block Creations by Japanese Adolescents

    Science.gov (United States)

    Kato, Daiki; Morita, Miyako

    2009-01-01

    This study examined general features of Lego block creations produced by Japanese adolescents with no known mental health disorders. The block creations of 33 participants were assessed for form, content, and gender differences. Time spent on the task, amount of area covered, and quantity and types of blocks used were measured and correlated with…

  17. The Barcelona Mobile Cluster: Actors, Contents and Trends

    Directory of Open Access Journals (Sweden)

    Carlos Alberto Scolari

    2009-07-01

    Full Text Available Communication mediated by mobile devices is one of the most dynamic sectors of the global economy and is transforming different aspects of our lives, including our ways of relating and our cultural production, distribution and consumption models. Media studies should not ignore these transformations. This paper presents the results of a study carried out during 2008 to determine the actors, contents produced and trends of the mobile communication companies in Barcelona. The study outlines an initial map of the situation, proposes a series of analysis categories and lays the foundations for more specific future studies on mCommunication.

  18. What's More Important--Literacy or Content? Confronting the Literacy-Content Dualism

    Science.gov (United States)

    Draper, Roni Jo; Smith, Leigh K.; Hall, Kendra M.; Siebert, Daniel

    2005-01-01

    The literacy-content dualism, which suggests that teachers must decide whether to provide literacy or content instruction, is a false dualism and adherence to it is detrimental to student participation in content-area reasoning, learning, and communicating. This article describes the experiences that prompted the teacher educators who authored…

  19. 21 CFR 101.60 - Nutrient content claims for the calorie content of foods.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Nutrient content claims for the calorie content of... Claims § 101.60 Nutrient content claims for the calorie content of foods. (a) General requirements. A claim about the calorie or sugar content of a food may only be made on the label or in the labeling of a...

  20. Effect of zirconia content and powder processing mechanical properties of gelcasted ZTA composite

    International Nuclear Information System (INIS)

    Khoshkalam, M.; Faghihi-Sani, M.A.; Nojoomi, A.

    2013-01-01

    Addition of fine zirconia particles in the alumina matrix in order to produce ZTA composite is a well-known method for improving the mechanical properties of alumina ceramics such as flexural strength and fracture toughness. Increasing homogeneity and reducing alumina grain size are two key factors for achieving proper mechanical properties in this ceramic matrix composite. In this work two batches of ZTA powder precursor were prepared through mixing of alumina and zirconia by ball milling and in situ synthesis of ZTA composite via solution combustion method. The bending strength testing samples were fabricated through gel-casting process. The effects of different powder processing methods as well as zirconia contents on microstructural homogeneity and mechanical properties of ZTA composites were investigated. The samples produced by solution combustion synthesized powder yielded higher homogeneity, finer microstructure and higher flexural strength. Results showed an upswing in the fracture toughness for the synthesized samples even up to 20 vol% zirconia, while the mixed samples depicted optimum fracture toughness in 10 vol% zirconia content. (author)

  1. Experimental investigation of solid oxide fuel cells using biomass gasification producer gases

    Energy Technology Data Exchange (ETDEWEB)

    Norheim, Arnstein

    2005-07-01

    The main objective of this thesis is theoretical and experimental investigations related to utilisation of biomass gasification producer gases as fuel for Solid Oxide Fuel Cells (SOFC). Initial fundamental steps towards a future system of combined heat and power production based on biomass gasification and SOFC are performed and include: 1) Theoretical modeling of the composition of biomass gasification producer gases. 2) Experimental investigation of SOFC performance using biomass gasification producer gas as fuel. 3) Experimental investigation of SOFC performance using biomass gasification producer gas containing high sulphur concentration. The modeling of the composition of gasifier producer gas was performed using the program FactSage. The main objective was to investigate the amount and speciation of trace species in the producer gases as several parameters were varied. Thus, the composition at thermodynamic equilibrium of sulphur, chlorine, potassium, sodium and compounds of these were established. This was done for varying content of the trace species in the biomass material at different temperatures and fuel utilisation i.e. varying oxygen content in the producer gas. The temperature interval investigated was in the range of normal SOFC operation. It was found that sulphur is expected to be found as H2S irrespective of temperature and amount of sulphur. Only at very high fuel utilisation some S02 is formed. Important potassium containing compounds in the gas are gaseous KOH and K. When chlorine is present, the amount of KOH and K will decrease due to the formation of KCI. The level of sodium investigated here was low, but some Na, NaOH and NaCl is expected to be formed. Below a certain temperature, condensation of alkali rich carbonates may occur. The temperature at which condensation begins is mainly depending on the amount of potassium present; the condensation temperature increases with increasing potassium content. In the first experimental work

  2. Titanium compacts produced by the pulvimetallurgical hydride-dehydride method for biomedical applications

    International Nuclear Information System (INIS)

    Barreiro, M M; Grana, D R; Kokubu, G A; Luppo, M I; Mintzer, S; Vigna, G

    2010-01-01

    Titanium powder production by the hydride-dehydride method has been developed as a non-expensive process. In this work, commercially pure grade two Ti specimens were hydrogenated. The hydrided material was milled in a planetary mill. The hydrided titanium powder was dehydrided and then sieved to obtain a particle size between 37 and 125 μm in order to compare it with a commercial powder produced by chemical reduction with a particle size lower than 150 μm. Cylindrical green compacts were obtained by uniaxial pressing of the powders at 343 MPa and sintering in vacuum. The powders and the density of sintered compacts were characterized, the oxygen content was measured and in vivo tests were performed in the tibia bones of Wistar rats in order to evaluate their biocompatibility. No differences were observed between the materials which were produced either with powders obtained by the hydride-dehydride method or with commercial powders produced by chemical reduction regarding modifications in compactation, sintering and biological behaviour.

  3. Titanium compacts produced by the pulvimetallurgical hydride-dehydride method for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Barreiro, M M [Materiales Dentales, Facultad de OdontologIa, Universidad de Buenos Aires, Marcelo T de Alvear 2142 (1122), Buenos Aires (Argentina); Grana, D R; Kokubu, G A [PatologIa I. Escuela de OdontologIa, Facultad de Medicina. Asociacion Odontologica Argentina-Universidad del Salvador, Tucuman 1845 (1050) Buenos Aires (Argentina); Luppo, M I; Mintzer, S; Vigna, G, E-mail: mbarreiro@mater.odon.uba.a, E-mail: dgrana@usal.edu.a, E-mail: luppo@cnea.gov.a, E-mail: vigna@cnea.gov.a [Departamento Materiales, Comision Nacional de Energia Atomica, Gral Paz 1499 (B1650KNA), San MartIn, Buenos Aires (Argentina)

    2010-04-15

    Titanium powder production by the hydride-dehydride method has been developed as a non-expensive process. In this work, commercially pure grade two Ti specimens were hydrogenated. The hydrided material was milled in a planetary mill. The hydrided titanium powder was dehydrided and then sieved to obtain a particle size between 37 and 125{mu}m in order to compare it with a commercial powder produced by chemical reduction with a particle size lower than 150{mu}m. Cylindrical green compacts were obtained by uniaxial pressing of the powders at 343 MPa and sintering in vacuum. The powders and the density of sintered compacts were characterized, the oxygen content was measured and in vivo tests were performed in the tibia bones of Wistar rats in order to evaluate their biocompatibility. No differences were observed between the materials which were produced either with powders obtained by the hydride-dehydride method or with commercial powders produced by chemical reduction regarding modifications in compactation, sintering and biological behaviour.

  4. The Effect of Crumb Rubber Particle Size to the Optimum Binder Content for Open Graded Friction Course

    Directory of Open Access Journals (Sweden)

    Mohd Rasdan Ibrahim

    2014-01-01

    Full Text Available The main objective of this paper is to investigate the relations of rubber size, rubber content, and binder content in determination of optimum binder content for open graded friction course (OGFC. Mix gradation type B as specified in Specification for Porous Asphalt produced by the Road Engineering Association of Malaysia (REAM was used in this study. Marshall specimens were prepared with four different sizes of rubber, namely, 20 mesh size [0.841 mm], 40 mesh [0.42 mm], 80 mesh [0.177 mm], and 100 mesh [0.149 mm] with different concentrations of rubberised bitumen (4%, 8%, and 12% and different percentages of binder content (4%–7%. The appropriate optimum binder content is then selected according to the results of the air voids, binder draindown, and abrasion loss test. Test results found that crumb rubber particle size can affect the optimum binder content for OGFC.

  5. Plasmaspheric electron content

    International Nuclear Information System (INIS)

    Hartmann, G.K.

    1978-01-01

    Measurements of the plasmaspheric electron content are reviewed with particular reference to the ATS-6 radio beacon experiment. From the review, it appears likely that measurement of the plasmaspheric electron content is the only one capable of monitoring electron fluxes continuously between L 1 and L 2. Some recent important results deduced from plasmaspheric electron content measurements are discussed

  6. Properties of retrograded and acetylated starch produced via starch extrusion or starch hydrolysis with pullulanase.

    Science.gov (United States)

    Kapelko, M; Zięba, T; Gryszkin, A; Styczyńska, M; Wilczak, A

    2013-09-12

    The aim of the present study was to determine the impact of serial modifications of starch, including firstly starch extrusion or hydrolysis with pullulanase, followed by retrogradation (through freezing and defrosting of pastes) and acetylation (under industrial conditions), on its susceptibility to amylolysis. The method of production had a significant effect on properties of the resultant preparations, whilst the direction and extent of changes depended on the type of modification applied. In the produced starch esters, the degree of substitution, expressed by the per cent of acetylation, ranged from 3.1 to 4.4 g/100 g. The acetylation had a significant impact on contents of elements determined with the atomic emission spectrometry, as it contributed to an increased Na content and decreased contents of Ca and K. The DSC thermal characteristics enabled concluding that the modifications caused an increase in temperatures and a decrease in heat of transition (or its lack). The acetylation of retrograded starch preparations increased their solubility in water and water absorbability. The modifications were found to exert various effects on the rheological properties of pastes determined based on the Brabender's pasting characteristics and flow curves determined with the use of an oscillatory-rotating viscosimeter. All starch acetates produced were characterized by ca. 40% resistance to amylolysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Chromatic and achromatic monocular deprivation produce separable changes of eye dominance in adults.

    Science.gov (United States)

    Zhou, Jiawei; Reynaud, Alexandre; Kim, Yeon Jin; Mullen, Kathy T; Hess, Robert F

    2017-11-29

    Temporarily depriving one eye of its input, in whole or in part, results in a transient shift in eye dominance in human adults, with the patched eye becoming stronger and the unpatched eye weaker. However, little is known about the role of colour contrast in these behavioural changes. Here, we first show that the changes in eye dominance and contrast sensitivity induced by monocular eye patching affect colour and achromatic contrast sensitivity equally. We next use dichoptic movies, customized and filtered to stimulate the two eyes differentially. We show that a strong imbalance in achromatic contrast between the eyes, with no colour content, also produces similar, unselective shifts in eye dominance for both colour and achromatic contrast sensitivity. Interestingly, if this achromatic imbalance is paired with similar colour contrast in both eyes, the shift in eye dominance is selective, affecting achromatic but not chromatic contrast sensitivity and revealing a dissociation in eye dominance for colour and achromatic image content. On the other hand, a strong imbalance in chromatic contrast between the eyes, with no achromatic content, produces small, unselective changes in eye dominance, but if paired with similar achromatic contrast in both eyes, no changes occur. We conclude that perceptual changes in eye dominance are strongly driven by interocular imbalances in achromatic contrast, with colour contrast having a significant counter balancing effect. In the short term, eyes can have different dominances for achromatic and chromatic contrast, suggesting separate pathways at the site of these neuroplastic changes. © 2017 The Author(s).

  8. Cold Spray Aluminum–Alumina Cermet Coatings: Effect of Alumina Content

    Science.gov (United States)

    Fernandez, Ruben; Jodoin, Bertrand

    2018-04-01

    Deposition behavior and deposition efficiency were investigated for several aluminum-alumina mixture compositions sprayed by cold spray. An increase in deposition efficiency was observed. Three theories postulated in the literature, explaining this increase in deposition efficiency, were investigated and assessed. Through finite element analysis, the interaction between a ceramic particle peening an impacting aluminum particle was found to be a possible mechanism to increase the deposition efficiency of the aluminum particle, but a probability analysis demonstrated that this peening event is too unlikely to contribute to the increment in deposition efficiency observed. The presence of asperities at the substrate and deposited layers was confirmed by a single-layer deposition efficiency measurement and proved to be a major mechanism in the increment of deposition efficiency of the studied mixtures. Finally, oxide removal produced by the impact of ceramic particles on substrate and deposited layers was evaluated as the complement of the other effects and found to also play a major role in increasing the deposition efficiency. It was found that the coatings retained approximately half of the feedstock powder alumina content. Hardness tests have shown a steady increase with the coating alumina content. Dry wear tests have revealed no improvement in wear resistance in samples with an alumina content lower than 22 wt.% compared to pure aluminum coatings. Adhesion strength showed a steady improvement with increasing alumina content in the feedstock powder from 18.5 MPa for pure aluminum coatings to values above 70 MPa for the ones sprayed with the highest feedstock powder alumina content.

  9. Production of microbial oil with high oleic acid content by Trichosporon capitatum

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Hong; Zong, Minhua [State Key Laboratory of Pulp and Paper Engineering, College of Light Industry and Food Sciences, South China University of Technology, Guangzhou 510640 (China); Li, Yuanyuan; Chen, Lei [School of Biosciences and Bioengineering, South China University of Technology, Guangzhou 510640 (China)

    2011-01-15

    Microbial oils with high unsaturated fatty acids content, especially oleic acid content, are good feedstock for high quality biodiesel production. Trichosporon capitatum was found to accumulate lipid with around 80% oleic acid and 89% total unsaturated fatty acids content on nitrogen-limited medium. In order to improve its lipid yield, effects of medium components and culture conditions on cell growth and lipid accumulation were investigated. Optimization of media resulted in a 61% increase in the lipid yield of T. capitatum after cultivation at 28 C and 160 rpm for 6 days. In addition, T. capitatum could grow well on cane molasses and afford a lipid yield comparable to that on synthetic nitrogen-limited medium. The biodiesel from the microbial oil produced by T. capitatum on cane molasses displayed a low cold filter plugging point (-15 C), and so T. capitatum might be a promising strain to provide lipid suitable for high quality biodiesel production. (author)

  10. The earthworm gut: an ideal habitat for ingested N2O-producing microorganisms.

    Science.gov (United States)

    Horn, Marcus A; Schramm, Andreas; Drake, Harold L

    2003-03-01

    The in vivo production of nitrous oxide (N(2)O) by earthworms is due to their gut microbiota, and it is hypothesized that the microenvironment of the gut activates ingested N(2)O-producing soil bacteria. In situ measurement of N(2)O and O(2) with microsensors demonstrated that the earthworm gut is anoxic and the site of N(2)O production. The gut had a pH of 6.9 and an average water content of approximately 50%. The water content within the gut decreased from the anterior end to the posterior end. In contrast, the concentration of N(2)O increased from the anterior end to the mid-gut region and then decreased along the posterior part of the gut. Compared to the soil in which worms lived and fed, the gut of the earthworm was highly enriched in total carbon, organic carbon, and total nitrogen and had a C/N ratio of 7 (compared to a C/N ratio of 12 in soil). The aqueous phase of gut contents contained up to 80 mM glucose and numerous compounds that were indicative of anaerobic metabolism, including up to 9 mM formate, 8 mM acetate, 3 mM lactate, and 2 mM succinate. Compared to the soil contents, nitrite and ammonium were enriched in the gut up to 10- and 100-fold, respectively. The production of N(2)O by soil was induced when the gut environment was simulated in anoxic microcosms for 24 h (the approximate time for passage of soil through the earthworm). Anoxia, high osmolarity, nitrite, and nitrate were the dominant factors that stimulated the production of N(2)O. Supplemental organic carbon had a very minimal stimulatory effect on the production of N(2)O, and addition of buffer or ammonium had essentially no effect on the initial N(2)O production rates. However, a combination of supplements yielded rates greater than that obtained mathematically for single supplements, suggesting that the maximum rates observed were due to synergistic effects of supplements. Collectively, these results indicate that the special microenvironment of the earthworm gut is ideally suited

  11. Sodium and potassium content and their ratio in meatballs in tomato sauce produced with lower amounts of sodium

    Science.gov (United States)

    Lilić, S.; Nikolić, D.; Pejkovski, Z.; Velebit, B.; Lakićević, B.; Korićanac, V.; Vranić, D.

    2017-09-01

    The goal of this study was to examine the possibility of partial replacement of sodium chloride with potassium chloride and ammonium chloride, with the target of achieving less sodium content in meatballs and tomato sauce as well as achieving a better Na:K ratio. The trial consisted of five groups. In the control group of meatballs and sauce, only sodium chloride was added. In group 1, half of the sodium chloride was replaced with potassium chloride related to control group while in group 2 one third of the sodium chloride was replaced with potassium chloride. In group 3, one third of the sodium chloride was replaced with ammonium chloride, and in group 4, sodium chloride was reduced to half the amount in the control group, and 1 g (0.25%) of ammonium chloride was also added. All products were acceptable according to sensory analyses. The largest reductions of sodium content were 44.64%, achieved in meatballs from group 1 and 50.62% in tomato sauce from group 4 in relation to meatballs and tomato sauce from control group. The highest Na:K ratio was calculated in meatballs and tomato sauce from control group, 2.88 and 4.39, respectively. The best Na:K ratio was in meatballs and tomato sauce from group 1, 0.60 and 0.92, respectively, in which half of sodium chloride was replaced with potassium chloride. However, in meatballs and tomato sauce from group 4, with only half the amount of sodium chloride related to control group, the Na:K ratio was worse because in these products, potassium chloride was not added.

  12. Pre-Service Teachers' Mathematics Content Knowledge: Implications for How Mathematics Is Taught in Higher Education

    Science.gov (United States)

    Lowrie, Tom; Jorgensen, Robyn

    2016-01-01

    This investigation explored pre-service teachers' mathematics content knowledge (MCK) and beliefs associated with mathematics education practices. An Exploratory Factor Analysis, conducted on a beliefs and attitudes questionnaire, produced three common attitude factors associated with (1) inquiry-based teaching; (2) how mathematics knowledge is…

  13. Preliminary Study on the Standard of Selenium Content in Agricultural Products

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhi-yuan; YOU Yong; GUO Qing-quan; WANG Yong-hong; DENG Shi-lin

    2012-01-01

    With the improvement of living standards, people pay more attention to the agricultural products with health protection function, and the selenium-rich agricultural products attract more and more consumers. The main biological role of selenium is to resist oxidation and inflammatory response, mainly focusing on resisting aging, preventing cardiovascular disease, protecting eyesight, counteracting or destroying the toxic properties, preventing cancer and thyroid disease. In most areas of China, there is a widespread shortage of selenium, thus producing selenium-rich agricultural products to provide natural selenium-rich health food to the areas in need of selenium, has gradually become a new hot spot of China’s health food industry, but high content of selenium in food is detrimental to human body, even leads to selenium intoxication, and artificially adding inorganic selenium is difficult to guarantee that the selenium content of agricultural products is not exceeded. According to human body’s daily demand for selenium in dietetics and the content of selenium in agricultural products in the Chinese food composition table, we put forward the recommendations on the standard of selenium in agricultural products, in order to provide the basis for China to formulate the health standard of selenium content in selenium-rich agricultural products.

  14. Water Content of Lunar Alkali Fedlspar

    Science.gov (United States)

    Mills, R. D.; Simon, J. I.; Wang, J.; Alexander, C. M. O'D.; Hauri, E. H.

    2016-01-01

    Detection of indigenous hydrogen in a diversity of lunar materials, including volcanic glass, melt inclusions, apatite, and plagioclase suggests water may have played a role in the chemical differentiation of the Moon. Spectroscopic data from the Moon indicate a positive correlation between water and Th. Modeling of lunar magma ocean crystallization predicts a similar chemical differentiation with the highest levels of water in the K- and Th-rich melt residuum of the magma ocean (i.e. urKREEP). Until now, the only sample-based estimates of water content of KREEP-rich magmas come from measurements of OH, F, and Cl in lunar apatites, which suggest a water concentration of alkali feldspar, a common mineral in K-enriched rocks, can have approx. 20 ppm of water, which implies magmatic water contents of approx. 1 wt % in the high-silica magmas. This estimate is 2 to 3 orders of magnitude higher than that estimated from apatite in similar rocks. However, the Cl and F contents of apatite in chemically similar rocks suggest that these melts also had high Cl/F ratios, which leads to spuriously low water estimates from the apatite. We can only estimate the minimum water content of urKREEP (+ bulk Moon) from our alkali feldspar data because of the unknown amount of degassing that led to the formation of the granites. Assuming a reasonable 10 to 100 times enrichment of water from urKREEP into the granites produces an estimate of 100-1000 ppm of water for the urKREEP reservoir. Using the modeling of and the 100-1000 ppm of water in urKREEP suggests a minimum bulk silicate Moon water content between 2 and 20 ppm. However, hydrogen loss was likely very significant in the evolution of the lunar mantle. Conclusions: Lunar granites crystallized between 4.3-3.8 Ga from relatively wet melts that degassed upon crystallization. The formation of these granites likely removed significant amounts of water from some mantle source regions, e.g. later mare basalts predicting derivation from a

  15. Comparison of Maraging Steel Micro- and Nanostructure Produced Conventionally and by Laser Additive Manufacturing

    Directory of Open Access Journals (Sweden)

    Eric A. Jägle

    2016-12-01

    Full Text Available Maraging steels are used to produce tools by Additive Manufacturing (AM methods such as Laser Metal Deposition (LMD and Selective Laser Melting (SLM. Although it is well established that dense parts can be produced by AM, the influence of the AM process on the microstructure—in particular the content of retained and reversed austenite as well as the nanostructure, especially the precipitate density and chemistry, are not yet explored. Here, we study these features using microhardness measurements, Optical Microscopy, Electron Backscatter Diffraction (EBSD, Energy Dispersive Spectroscopy (EDS, and Atom Probe Tomography (APT in the as-produced state and during ageing heat treatment. We find that due to microsegregation, retained austenite exists in the as-LMD- and as-SLM-produced states but not in the conventionally-produced material. The hardness in the as-LMD-produced state is higher than in the conventionally and SLM-produced materials, however, not in the uppermost layers. By APT, it is confirmed that this is due to early stages of precipitation induced by the cyclic re-heating upon further deposition—i.e., the intrinsic heat treatment associated with LMD. In the peak-aged state, which is reached after a similar time in all materials, the hardness of SLM- and LMD-produced material is slightly lower than in conventionally-produced material due to the presence of retained austenite and reversed austenite formed during ageing.

  16. Comparison of Maraging Steel Micro- and Nanostructure Produced Conventionally and by Laser Additive Manufacturing.

    Science.gov (United States)

    Jägle, Eric A; Sheng, Zhendong; Kürnsteiner, Philipp; Ocylok, Sörn; Weisheit, Andreas; Raabe, Dierk

    2016-12-24

    Maraging steels are used to produce tools by Additive Manufacturing (AM) methods such as Laser Metal Deposition (LMD) and Selective Laser Melting (SLM). Although it is well established that dense parts can be produced by AM, the influence of the AM process on the microstructure-in particular the content of retained and reversed austenite as well as the nanostructure, especially the precipitate density and chemistry, are not yet explored. Here, we study these features using microhardness measurements, Optical Microscopy, Electron Backscatter Diffraction (EBSD), Energy Dispersive Spectroscopy (EDS), and Atom Probe Tomography (APT) in the as-produced state and during ageing heat treatment. We find that due to microsegregation, retained austenite exists in the as-LMD- and as-SLM-produced states but not in the conventionally-produced material. The hardness in the as-LMD-produced state is higher than in the conventionally and SLM-produced materials, however, not in the uppermost layers. By APT, it is confirmed that this is due to early stages of precipitation induced by the cyclic re-heating upon further deposition-i.e., the intrinsic heat treatment associated with LMD. In the peak-aged state, which is reached after a similar time in all materials, the hardness of SLM- and LMD-produced material is slightly lower than in conventionally-produced material due to the presence of retained austenite and reversed austenite formed during ageing.

  17. Content of heavymetals in Gentiana lutea L. roots and galenic forms

    Directory of Open Access Journals (Sweden)

    DRAGOJA RADANOVIC

    2007-02-01

    Full Text Available An experimental field for the cultivated production of Gentiana lutea L. was established five years ago at the Suvobor Mountain, Serbia. Soil analysis of this area revealed the occurrence of high pseudo-total (Ni – 1270 mg/kg, Cr – 423 mg/kg, Co – 385 mg/kg and available (especially Ni – 133 mg/kg heavy metals contents in the soil. Hence, the aim of this research was to evaluate the quality of Gentiana lutea L. – roots and galenic forms (liquid extract in 70 % ethanol, spissum and siccum produced from the roots, because, for most plants, heavy metals accumulate in the root tissue. The amounts of Ni and Cr found in the analyzed roots were very high (54 mg/kg and 14 mg/kg, respectively. The efficiency of ethanol in extracting heavy metals from the roots varied depending on the particular element. The highest efficiency was obtained for Ni (41.3 %, then for Cd (39.5 %, Pb (37.0% and Co (30.4 %. According to this, a potential hazard exists for humans, if gentian's galenic forms are produced from the raw material with high heavy metals contents. It is concluded that quality control of the raw material must be carried out before further utilization of gentian.

  18. The salt content of products from popular fast-food chains in Costa Rica.

    Science.gov (United States)

    Heredia-Blonval, Katrina; Blanco-Metzler, Adriana; Montero-Campos, Marielos; Dunford, Elizabeth K

    2014-12-01

    Salt is a major determinant of population blood pressure levels. Salt intake in Costa Rica is above levels required for good health. With an increasing number of Costa Ricans visiting fast food restaurants, it is likely that fast-food is contributing to daily salt intake. Salt content data from seven popular fast food chains in Costa Rica were collected in January 2013. Products were classified into 10 categories. Mean salt content was compared between chains and categories. Statistical analysis was performed using Welch ANOVA and Tukey-Kramer HSD tests. Significant differences were found between companies; Subway products had lowest mean salt content (0.97 g/100 g; p KFC had the highest (1.57 g/100 g; p < 0.05). Significant variations in mean salt content were observed between categories. Salads had a mean salt content of 0.45 g/100 g while sauces had 2.16 g/100 g (p < 0.05). Wide variation in salt content was also seen within food categories. Salt content in sandwiches ranged from 0.5 to 2.1 g/100 g. The high levels and wide variation in salt content of fast food products in Costa Rica suggest that salt reduction is likely to be technically feasible in many cases. With an increasing number of consumers purchasing fast foods, even small improvements in salt levels could produce important health gains. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

  19. A Comparison of the Essential Amino Acid Content and the Retention Rate by Chicken Part according to Different Cooking Methods.

    Science.gov (United States)

    Kim, Honggyun; Do, Hyun Wook; Chung, Heajung

    2017-01-01

    This study set out to identify the changes in the nutrient contents during the chicken cooking process as basic data for the establishment of a national health nutrition policy. Samples were produced using 3 chicken parts (wing, breast, and leg) and 7 cooking methods (boiling, pancooking, pan-frying, deep-frying, steaming, roasting, and microwaving), and the essential amino acid contents, principal components, and retention rates were analyzed. Weight loss was observed in all chicken parts with all cooking methods. The protein and essential amino acid contents of the chicken samples differed significantly according to the part and the cooking method ( p chicken parts showed ranges of 16.81-32.36 and 0.44-2.45, respectively. The principal component analysis (PCA) clearly demonstrated that the cooking methods and chicken parts produced similar trends for the essential amino acid contents. The retention rates of the chicken parts varied with the cooking methods, yielding a minimum value of 83% for isoleucine in a roasted wing, 91% for protein in a steamed breast, and 77% for isoleucine and lysine in a roasted leg. Therefore, the protein and amino acid contents of the roasted breast were higher than those of the other cooked chicken parts.

  20. Draft Genome Sequence of Bacillus velezensis GF610, a Producer of Potent Anti-Listeria Agents.

    Science.gov (United States)

    Gerst, Michelle M; Dudley, Edward G; Xiaoli, Lingzi; Yousef, Ahmed E

    2017-10-12

    Bacillus velezensis GF610 was isolated from soil in Illinois, USA, and found to produce amyloliquecidin GF610, a potent two-component antimicrobial peptide. We report here the GF610 strain draft genome sequence, which contains 4.29 Mb and an overall GC content of 45.91%. Copyright © 2017 Gerst et al.

  1. Man-made vitreous fiber produced from incinerator ash using the thermal plasma technique and application as reinforcement in concrete.

    Science.gov (United States)

    Yang, Sheng-Fu; Wang, To-Mai; Lee, Wen-Cheng; Sun, Kin-Seng; Tzeng, Chin-Ching

    2010-10-15

    This study proposes using thermal plasma technology to treat municipal solid waste incinerator ashes. A feasible fiberization method was developed and applied to produce man-made vitreous fiber (MMVF) from plasma vitrified slag. MMVF were obtained through directly blending the oxide melt stream with high velocity compressed air. The basic technological characteristics of MMVF, including morphology, diameter, shot content, length and chemical resistance, are described in this work. Laboratory experiments were conducted on the fiber-reinforced concrete. The effects of fibrous content on compressive strength and flexural strength are presented. The experimental results showed the proper additive of MMVF in concrete can enhance its mechanical properties. MMVF products produced from incinerator ashes treated with the thermal plasma technique have great potential for reinforcement in concrete. 2010 Elsevier B.V. All rights reserved.

  2. A co-regulatory approach to stay safe online : reporting inappropriate content with the MediaKids mobile app

    OpenAIRE

    Poblet, Marta

    2016-01-01

    The convergence of mobile technologies, media, and the Internet is transforming the way that digital content is produced, distributed, and consumed, especially among children and young adults. In Europe as in many other areas, minors are exposed to an ever-growing amount of digital content on mobile phones, tablets, or computer screens. Increasing exposure at an early age brings both new opportunities and risks. This paper reviews the current discussion about strategies that deal with inappro...

  3. The effects of gamma irradiation on the vitamin E content and sensory qualities of pecan nuts (Carya illinoensis)

    Energy Technology Data Exchange (ETDEWEB)

    Taipina, Magda S. [Nuclear and Energy Research Institute, IPEN-CNEN/SP, Av. Prof. L. Prestes 2242, 05508-000 Sao Paulo (Brazil); Lamardo, Leda C.A.; Rodas, Maria A.B. [Instituto Adolfo Lutz, Av. Dr. Arnaldo 355, 01246-902 Sao Paulo, SP (Brazil); Mastro, Nelida L. del [Nuclear and Energy Research Institute, IPEN-CNEN/SP, Av. Prof. L. Prestes 2242, 05508-000 Sao Paulo (Brazil)], E-mail: nlmastro@ipen.br

    2009-07-15

    Pecan nuts (Carya illinoensis) were treated with gamma irradiation and evaluated for changes in vitamin E content and sensory properties. Irradiation at 1 and 3 kGy resulted in no changes in vitamin E content measured as {alpha}-tocopherol equivalents by a colorimetric method. A trained sensory panel found that irradiation at 1 kGy produced no significant changes in appearance, aroma, texture and flavor attributes. The vitamin E content of irradiated pecan nuts remained stable, but from the point of view of sensory quality a dose of merely 1 kGy can be considered as recommendable.

  4. The effects of gamma irradiation on the vitamin E content and sensory qualities of pecan nuts (Carya illinoensis)

    International Nuclear Information System (INIS)

    Taipina, Magda S.; Lamardo, Leda C.A.; Rodas, Maria A.B.; Mastro, Nelida L. del

    2009-01-01

    Pecan nuts (Carya illinoensis) were treated with gamma irradiation and evaluated for changes in vitamin E content and sensory properties. Irradiation at 1 and 3 kGy resulted in no changes in vitamin E content measured as α-tocopherol equivalents by a colorimetric method. A trained sensory panel found that irradiation at 1 kGy produced no significant changes in appearance, aroma, texture and flavor attributes. The vitamin E content of irradiated pecan nuts remained stable, but from the point of view of sensory quality a dose of merely 1 kGy can be considered as recommendable.

  5. The effects of gamma irradiation on the vitamin E content and sensory qualities of pecan nuts ( Carya illinoensis)

    Science.gov (United States)

    Taipina, Magda S.; Lamardo, Leda C. A.; Rodas, Maria A. B.; del Mastro, Nelida L.

    2009-07-01

    Pecan nuts ( Carya illinoensis) were treated with gamma irradiation and evaluated for changes in vitamin E content and sensory properties. Irradiation at 1 and 3 kGy resulted in no changes in vitamin E content measured as α-tocopherol equivalents by a colorimetric method. A trained sensory panel found that irradiation at 1 kGy produced no significant changes in appearance, aroma, texture and flavor attributes. The vitamin E content of irradiated pecan nuts remained stable, but from the point of view of sensory quality a dose of merely 1 kGy can be considered as recommendable.

  6. Decreasing the NO3 and increasing the vitamin C contents in spinach by a nitrogen deprivation method.

    Science.gov (United States)

    Mozafar, A

    1996-02-01

    Excessive use of nitrogen fertilizers is known to increase the NO3 and reduce the vitamin C contents in fruits and vegetables. We investigated the concentration of these compounds in spinach leaves when plants were transferred to nitrogen-free media prior to their harvest. It was noted that a pre-harvest transfer of spinach to N-free media reduces the NO3 and increases the vitamin C content of the leaves by a substantial amount in a 2-3 day period. It is suggested that this technique may be suited to produce spinach or other leafy vegetables with low NO3 and high vitamin C contents under commercial hydroponic conditions.

  7. Determination of the water content in tetra-ammonium uranyl tricarbonate by the Karl Fischer reagent method

    International Nuclear Information System (INIS)

    Sisti, C.; Grigoletto, T.

    1990-08-01

    Two methods are compared for the determination of water content in tetra-ammonium uranyl tricarbonate by the Karl Fischer reagent method. In the first method it is Known that the carbonate reacts stoichiometrically with the iodine content of the Karl Fischer reagent in the same way it reacts with the water (mole of apparent H 2 O per mole of carbonate is produced). In this case, the carbonate content in the sample is determined and a suitable correction is applied to take into account the apparent water results. In the second method it is performed an extraction of the moisture by adding methanol to the sample in an independent flask. After the decantation, an aliquot of the clear supernatant methanol is taken for the determination of water content by the Karl Fischer reagent method. (author) [pt

  8. Determination of the monosaccharide and alcohol content of balsamic and other vinegars by enzymatic methods

    Energy Technology Data Exchange (ETDEWEB)

    Plessi, M.; Monzani, A.; Coppini, D.

    1988-01-23

    The contents of monosaccharides and alcohol in bulsamic and other vinegars were determined by the enzymatic method. The traditional, unique balsamic vinegar is produced by the traditional method in modena. The older the balsamic vinegar, the higher the contents of dextrose and fructose are. The existence of wine vinegar added to the traditional balsami vinegar can be judged from the contents of them. The contents of dextrose and fructose in apple vinegar are low or medium, while those in the wine vinegar is very low. The ratio of dextrose to fructose varies according to the samples. Although sorbitol is contained in the apple vinegar, it is hardly contained in the commercially available wine vinegar. A little xylitol is contained in all the samples, while a large amount of it is contained in the apple vinegar. A sure indication of the quality and sound preparation is given by the content of glycerol which is found in all the vinegars and most distingushed in the traditional balsamic vinegar. (6 tabs, 20 refs)

  9. Volatile compounds of Aspergillus strains with different abilities to produce ochratoxin A.

    Science.gov (United States)

    Jeleń, Henryk H; Grabarkiewicz-Szczesna, Jadwiga

    2005-03-09

    Volatile compounds emitted by Aspergillus strains having different abilities to produce ochratoxin A were investigated. Thirteen strains of Aspergillus ochraceus, three belonging to the A. ochraceus group, and eight other species of Aspergillus were examined for their abilities to produce volatile compounds and ochratoxin A on a wheat grain medium. The profiles of volatile compounds, analyzed using SPME, in all A. ochraceus strains, regardless of their toxeginicity, were similar and comprised mainly of 1-octen-3-ol, 3-octanone, 3-octanol, 3-methyl-1-butanol, 1-octene, and limonene. The prevailing compound was always 1-octen-3-ol. Mellein, which forms part of the ochratoxin A molecule, was found in both toxigenic and nontoxigenic strains. Volatile compounds produced by other Aspergillus strains were similar to those of A. ochraceus. Incubation temperatures (20, 24, and 27 degrees C) and water content in the medium (20, 30, and 40%) influenced both volatile compounds formation and ochratoxin A biosynthesis efficiency, although conditions providing the maximum amount of volatiles were different from those providing the maximum amount of ochratoxin A. The pattern of volatiles produced by toxigenic A. ochraceus strains does not facilitate their differentiation from nontoxigenic strains.

  10. Techno-Economic Analysis of the Optimum Softwood Lignin Content for the Production of Bioethanol in a Repurposed Kraft Mill

    Directory of Open Access Journals (Sweden)

    Shufang Wu

    2014-09-01

    Full Text Available Kraft pulping is one possible pretreatment for softwood to economically produce bioethanol. This work evaluates the techno-economic potential of using the kraft process for producing bioethanol from softwoods in a repurposed or co-located kraft mill. Pretreated loblolly pine was enzymatically hydrolyzed at low enzyme dosages of 5 and 10 FPU/g of substrate. Pretreated residue with 13% lignin content had the highest sugar recovery, 32.7% and 47.7% at 5 and 10 FPU/g, respectively. The pretreated residues were oxygen delignified and refined. In all cases, oxygen delignification improved sugar recovery, while refining was mostly effective for pulps with high lignin content. At 5 FPU/g, the sugar recovery for all kraft pulps was 51 to 53% with oxygen delignification and refining. Increasing the enzyme dosage to 10 FPU/g increased the sugar recovery for these pulps to greater than 60%. Economic analysis for the pulps with different initial lignin content showed that kraft pulps with an initial lignin content of 6.7% with oxygen delignification had an ethanol yield of 285 L/ODt wood and the lowest total production cost of $0.55/L. Pulps with initial lignin content of 18.6% had a total production cost of $0.64/L with an ethanol yield of 264 L/ODt wood.

  11. Remedial measures in Czech houses with high radium content in building material

    International Nuclear Information System (INIS)

    Hulka, J.; Thomas, J.

    1999-01-01

    Three groups of houses built from materials having elevated natural radioactivity content were found in the Czech republic. These are: 1) about hundred old houses in Jachymov (Joachimstal) in Northern Bohemia, where residues from factory producing uranium paints were used as plaster and mortar before the World War II (radium concentration up to 1 MBq/kg, indoor gamma dose rate up to 10-100 μGy/h); 2) some 20 000 family houses built from highly emanating aerated concrete with radium content 500-1000 Bq/kg (produced from flying ash) in the period 1963-1980; 3) more than 2000 family houses from slag concrete of radium content about 3 kBq/kg in average (indoor gamma dose rate up to 2 μGy/h) made in the period 1972-83. Remedy measures were undertaken with state financial support. Intervention levels were laid down 200 Bq/m 3 for EEC (equivalent equilibrium radon concentration - it is equivalent to radon gas concentration 500 Bq/m 3 ), 2 μGy/h for indoor gamma dose rate. Weighted sum of indoor radon and indoor gamma dose rate was used if the latter was above 0,5 μGy/h. The central heat recovery ventilation units were used largely as the remedy measures. Some houses were demolished, in some houses local contamination of plasters was removed. Other tested measures (removal of the contaminated building material in great amount, gamma shielding, wall coating, etc.) proved to be not effective or not acceptable in practice. (author)

  12. Aflatoxin-producing Aspergillus spp. and aflatoxin levels in stored cassava chips as affected by processing practices

    DEFF Research Database (Denmark)

    Essono, G.; Ayodele, M.; Akoa, A.

    2009-01-01

    . The levels of aflatoxin ranged between 5.2 and 14.5 ppb. The distribution of aflatoxin in positive samples depended on 8 parameters including pH, moisture content, storage duration, types of chips, level of contamination by aflatoxin-producing fungi, processing practices and storage facilities. From analysis......), followed by A. nomius (58 isolates in 15 samples), whereas A. parasiticus was rarest. A direct competitive Enzyme-linked immunosorbent assay (ELISA)-based method was implemented to quantify the content in aflatoxins. Eighteen of the samples contained some aflatoxins at detectable levels whereas 54 did not...... of variance results, only pH (p levels were...

  13. Evaluating Content Dimensions in Entrepreneurship Education

    DEFF Research Database (Denmark)

    Moberg, Kåre

    Interest in entrepreneurship education is growing over the world, especially in innovation based economies, such as Denmark (GEM, 2010). However, we know rather little about the outcomes of entrepreneurship education, in particular with respect to which type of course content produces the best...... and models that allow us to evaluate the outcomes of different types of entrepreneurship courses. In the beginning of 2011, the Danish Foundation for Entrepreneurship – Young Enterprise initiated a research project with the aim to further our understanding of the type of impact entrepreneurship education...... and different educational designs have on different types of students. Two longitudinal surveys, one with a focus on elementary- and secondary-level education and one with focus on tertiary-level education, will be performed and databases with students from all levels of the Danish educational system...

  14. Management principles of the interaction between market attractiveness producer and its recipients

    OpenAIRE

    O.V. Sviridova

    2013-01-01

    The aim of the article. The article is devoted to the definition of the content of interaction between attractiveness producer and its recipients through the prism of general and derived management principles. Actuality of this article is caused by the formation of long-term relationships between business subjects. The main aim of these relationships is attracting and using of resources to further joint production and benefits distribution from these activities. Formation of such long-term re...

  15. Albumin/gentamicin microspheres produced by supercritical assisted atomization: optimization of size, drug loading and release.

    Science.gov (United States)

    Della Porta, G; Adami, R; Del Gaudio, P; Prota, L; Aquino, R; Reverchon, E

    2010-11-01

    In this work, the supercritical assisted atomization (SAA) is proposed, for the first time, not only as a micronization technology but also as a thermal coagulation process for the production of bovine serum albumin (BSA) microspheres charged with Gentamicin sulfate (GS). Particularly, different water solutions of BSA/GS were processed by SAA to produce protein microspheres with different size and antibiotic content. SAA precipitation temperature was selected in the range 100-130 °C to generate protein coagulation and to recover micronized BSA in form of hydrophobic aggregates; GS loading was varied between 10% and 50% (w/w) with an encapsulation efficiency which often reached 100%. In all cases, spherical and noncoalescing particles were successfully produced with a mean particle size of 2 µm and with a standard deviation of about ±1 µm. The microspheres also showed a good stability and constant water content after 60 days of storage. The release profiles of the entrapped drug were monitored using Franz cells to evaluate the possible application of the produced microspheres in wound dressing formulations. Particularly, the microspheres with a BSA/GS ratio of 4:1 after the first burst effect (of 40% of GS loaded) were able to release the GS continuously over 10 days. © 2010 Wiley-Liss, Inc. and the American Pharmacists Association

  16. The content of landscape form [the limits of formalism

    Directory of Open Access Journals (Sweden)

    Marc Treib

    2001-12-01

    Full Text Available The values behind the question of landscape appreciation and evaluation also inform the greater question of landscape content. Here the content of landscape architecture is taken as the raw material transformed through design, material from which we may derive pleasure and/or significance. What sort of raw material, its potential and its relevance, is the essay's base subject. Admittedly, structure, space, and pattern may constitute content in and of themselves: a poetics of form and space. But deeper works may result from using these vehicles to embody other types of content, among them the understanding and judicious application of ecological processes (including the immediate as well as larger site over time, and the regard for humans singly and in groups, contemporary and over time. The manner in which the designer addresses these factors may also elevate a physical statement of these concerns, alone or together, to a poetic level. It is admittedly a difficult task, and without doubt, no work is ever perfect in all respects. Nonetheless, several landscape architects currently in practice have produced designs with these considerations at their core. The work of Hargreaves Associates in the United States, and Georges Descombes and Dieter Kienast in Switzerland serve as the prime case studies. The landscape architect's project here utilizes the eternalized moment of history to inform the making of physical places. The landscape must succeed in the present - social provisions, construction intelligence, aesthetic interest - amalgamating the voices of the past with those of the "now."

  17. Sharing of Alcohol-Related Content on Social Networking Sites: Frequency, Content, and Correlates.

    Science.gov (United States)

    Erevik, Eilin K; Torsheim, Torbjørn; Vedaa, Øystein; Andreassen, Cecilie S; Pallesen, Ståle

    2017-05-01

    The present study aimed to explore students' reports of their sharing of alcohol-related content on different social networking sites (i.e., frequency of sharing and connotations of alcohol-related posts), and to identify indicators of such posting. Students at the four largest institutions for higher education in Bergen, Norway, were invited to participate in an Internet-based survey. The sample size was 11,236 (a 39.4% response rate). The survey included questions about disclosure of alcohol-related content on social networking sites, alcohol use (using the Alcohol Use Disorders Identification Test), personality factors (using the Mini-IPIP), and demographic characteristics. Binary logistic regressions were used to analyze indicators of frequent sharing of alcohol-related content depicting positive and negative aspects of alcohol use. A majority of the students had posted alcohol-related content (71.0%), although few reported having done so frequently. Positive aspects of alcohol use (e.g., enjoyment or social community) were most frequently shared. Young, single, and extroverted students with high alcohol consumption were more likely to report frequent sharing of alcohol-related content. Positive attitudes toward posting alcohol-related content and reports of exposure to such content particularly increased the likelihood of one's own posting of alcohol-related content. Positive aspects of alcohol use seem to be emphasized on social networking sites. Sharing of alcohol-related content is associated with heightened alcohol use, which implies that such sites can be relevant for prevention agents. Social influence from social networking sites, such as exposure to others' alcohol-related content, is associated with one's own sharing of similar content.

  18. Qualitative Content Analysis

    OpenAIRE

    Philipp Mayring

    2000-01-01

    The article describes an approach of systematic, rule guided qualitative text analysis, which tries to preserve some methodological strengths of quantitative content analysis and widen them to a concept of qualitative procedure. First the development of content analysis is delineated and the basic principles are explained (units of analysis, step models, working with categories, validity and reliability). Then the central procedures of qualitative content analysis, inductive development of ca...

  19. Correlation between the oxide impedance and corrosion behavior of Zr-Nb-Sn-Fe-Cu alloys

    Science.gov (United States)

    Park, Sang-Yoon; Lee, Myung-Ho; Jeong, Yong-Hwan; Jung, Youn-Ho

    2004-12-01

    The correlation between the oxide impedance and corrosion behavior of two series of Zr-Nb-Sn-Fe-Cu alloys was evaluated. Corrosion tests were performed in a 70 ppm LiOH aqueous solution at 360°C for 300 days. The results of the corrosion tests revealed that the corrosion behavior of the alloys depended on the Nb and Sn content. The impedance characteristics for the pre- and post-transition oxide layers formed on the surface of the alloys were investigated in sulfuric acid at room temperature. From the results, a pertinent equivalent circuit model was preferably established, explaining the properties of double oxide layers. The impedance of the oxide layers correlated with the corrosion behavior; better corrosion resistance always showed higher electric resistance for the inner layers. It is thus concluded that a pertinent equivalent circuit model would be useful for evaluating the long-term corrosion behavior of Zr-Nb-Sn-Fe-Cu alloys.

  20. Medium Density Fibreboard Made from Kenaf (Hibiscus cannabinus L. Stem: Effect of Thermo-mechanical Refining and Resin Content

    Directory of Open Access Journals (Sweden)

    Majid Dehghan Nayeri

    2014-03-01

    Full Text Available The present study deals with the physical and mechanical properties of dry-formed medium density fibreboard (MDF made from renewable biomass kenaf (Hibiscus cannabinus L. stem as a function of adhesive level and refining conditions. Raw material was prepared by heating for 5 min at pressure levels of 6 and 8 bars. Experimental samples with a target density of 700 kgm-3 were produced with 10, 12, or 14% urea formaldehyde as a binder. Physical properties of MDF panels, such as thickness swelling (TS and water absorption (WA as well as mechanical properties including modulus of rupture (MOR, modulus of elasticity (MOE, and internal bonding (IB, were evaluated. Based on the test results, resin content and refining pressure have significant effects on the physical and mechanical properties of MDF panels. High resin content and pressure produced MDF boards with low WA and TS but high MOR, MOE, and IB. At 8 bars pressure and 14% resin content, the MDF recorded optimum WA (83.12%, TS (20.2%, MOR (25.3 MPa, MOE (3450 MPa, and IB (0.51 MPa.

  1. Formation of volatile compounds in kefir made of goat and sheep milk with high polyunsaturated fatty acid content.

    Science.gov (United States)

    Cais-Sokolińska, D; Wójtowski, J; Pikul, J; Danków, R; Majcher, M; Teichert, J; Bagnicka, E

    2015-10-01

    This article explored the formation of volatile compounds during the production of kefir from goat and sheep milks with high polyunsaturated fatty acids (PUFA) as a result of feeding animals forage supplemented with maize dried distillers grains with solubles (DDGS). The increased PUFA content of the goat and sheep milks resulted in significant changes to the fermentation process. In particular, apart from an increase in the time taken to ferment sheep milk, fermentation yielded less 2,3-butanedione. The highest quantities of this compound were assayed in kefir produced from goat milk with an increased content of PUFA. An increase of PUFA significantly elevated ethanal synthesis during lactose-alcohol fermentation of sheep milk. Neither the origin of milk (sheep or goat) nor the level of PUFA had any statistical effect on the amount of ethanal assayed during the fermentation of milk and within the finished product. The proportion of l(+)-lactic acid was higher in kefirs produced using goat milk compared with sheep milk and did not depend on the content of PUFA in milk fat. The content of PUFA had a significant effect on the aroma profile of the resulting kefirs. An increase in PUFA content resulted in the loss of whey aroma in goat milk kefirs and the animal odor in sheep milk kefirs, and a creamy aroma became more prevalent in kefirs made from sheep milk. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  2. Enzymatic pulp upgrade for producing high-value cellulose out of a Kraft paper pulp.

    Science.gov (United States)

    Hutterer, Christian; Kliba, Gerhard; Punz, Manuel; Fackler, Karin; Potthast, Antje

    2017-07-01

    The high-yield separation of polymeric parts from wood-derived lignocellulosic material is indispensable in biorefinery concepts. For the separation of cellulose and xylan from hardwood paper pulps to obtain pulps of high cellulose contents, simple alkaline extractions were found to be the most suitable technology, although having certain limitations. These are embodied by residual alkali resistant xylan incorporated in the pulp matrix. Further purification in order to produce pure cellulose with a low uniformity could be achieved selectively degrading residual xylan and depolymerizing the cellulose macromolecules by xylanase and cellulase. The latter help to adjust cellulose chain lengths for certain dissolving pulp grades while reducing the demand for ozone in subsequent TCF bleaching. Experiments applying different commercially available enzyme preparations revealed the dependency of xylanase performance on the residual xylan content in pulps being stimulated by additional cellulase usage. The action of the latter strongly depends on the cellulose allomorphy confirming the impact of the pulp morphology. Hence, the combined application of both types of enzymes offers a high potential for upgrading pulps in order to produce a pure and high-value cellulose product. Copyright © 2017 Elsevier Inc. All rights reserved.

  3. Antioxidant properties, total phenolic and total flavonoid content of the Slovak white wines – welschriesling and chardonnay

    Directory of Open Access Journals (Sweden)

    Daniel Bajčan

    2017-01-01

    Full Text Available The biologically active compounds in wines, especially phenolics, are responsible for reduced risk of developing chronic diseses (cardiovascular diseases, cancer, diabetes, Alzheimer disease, etc., due to their antioxidant activities. Twenty six Slovak white wines, produced from different geographical origins, were examined in this study. The antioxidant activity, total phenolic and flavonoid contents of two types monovarietal wines - Welschriesling and Chardonnay were evaluated. All three mentioned parameters were determined by UV-VIS absorption spectrometry. The results showed that both types of Slovak white wines were high in polyphenols (average content was 303.2 mg GAE.L-1 in Welschriesling, resp. 355.6 mg GAE.L-1 in Chardonnay and flavonoids (average content was 51.9 mg CE.L-1 in Welschriesling, resp. 60.1 mg CE.L-1 in Chardonnay, as well as a high antioxidant activity (average value was 35.0% inhibition of DPPH in Welschriesling, resp. 43.3% inhibition of DPPH in Chardonnay, comparable to the wines produced in other regions in the world. Among the white wines, Chardonnay had higher content of total polyphenols, as well as flavonoids and higher values of antioxidant activity. Our results confirmed very strong linear correlations between all three analysed parameters (TPC, TFC and AA: TPC and TFC (r = 0.818, AA and TPC (r = 0.699, resp. TFC and AA (r = 0.693.

  4. Lithium-Vanadium bronzes as model catalysts for the selective reduction of nitric oxide

    NARCIS (Netherlands)

    Bosch, H.; Bongers, Annemie; Enoch, Gert; Snel, Ruud; Ross, Julian R.H.

    1989-01-01

    The effect of alkali metals on the selective reduction of nitric oxide with ammonia has been studied on bulk iron oxide and bulk vanadium oxide. The influence of additions of LiOH, NaOH and KOH on the activity was screened by pulse experiments carried out in the absence of gaseous oxygen; FTIR

  5. Hydrogen production by ethanol partial oxidation over nano-iron oxide catalysts produced by chemical vapour synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, Wael Ahmed Abou Taleb Sayed

    2011-01-13

    This work presents the experimental results of the synthesis of unsupported and supported SiC iron oxide nanoparticles and their catalytic activity towards ethanol partial oxidation. For comparison, further unsupported iron oxide phases were investigated towards the ethanol partial oxidation. These {gamma}-Fe{sub 2}O{sub 3} and {alpha}/{gamma}-Fe{sub 2}O{sub 3} phase catalysts were prepared by the CVS method using Fe(CO){sub 5} as precursor, supplied by another author. The {alpha}-Fe{sub 2}O{sub 3} and SiC nanoparticles were prepared by the CVS method using a home made hot wall reactor technique at atmospheric pressure. Ferrocene and tetramethylsilane were used as precursor for the production process. Process parameters of precursor evaporation temperature, precursor concentration, gas mixture velocity and gas mixture dilution were investigated and optimised to produce particle sizes in a range of 10 nm. For Fe{sub 2}O{sub 3}/SiC catalyst series production, a new hot wall reactor setup was used. The particles were produced by simultaneous thermal decomposition of ferrocene and tetramethylsilane in one reactor from both sides. The production parameters of inlet tube distance inside the reactor, precursor evaporation temperature and carrier gas flow were investigated to produce a series of samples with different iron oxide content. The prepared catalysts composition, physical and chemical properties were characterized by XRD, EDX, SEM, BET surface area, FTIR, XPS and dynamic light scattering (DLS) techniques. The catalytic activity for the ethanol gas-phase oxidation was investigated in a temperature range from 260 C to 290 C. The product distributions obtained over all catalysts were analysed with mass spectrometry analysis tool. The activity of bulk Fe{sub 2}O{sub 3} and SiC nanoparticles was compared with prepared nano-iron oxide phase catalysts. The reaction parameters, such as reaction temperature and O{sub 2}/ethanol ratio were investigated. The catalysts

  6. Fatigue behavior of highly porous titanium produced by powder metallurgy with temporary space holders

    Energy Technology Data Exchange (ETDEWEB)

    Özbilen, Sedat [Forschungszentrum Jülich, Institute of Energy and Climate Research (IEK), 52425 Jülich (Germany); Gazi University, Faculty of Technology, Department of Metallurgical and Materials Engineering, Teknikokullar, Ankara (Turkey); Liebert, Daniela [Forschungszentrum Jülich, Institute of Energy and Climate Research (IEK), 52425 Jülich (Germany); Beck, Tilmann [Forschungszentrum Jülich, Institute of Energy and Climate Research (IEK), 52425 Jülich (Germany); University of Kaiserslautern, Lehrstuhl für Werkstoffkunde (WKK), D-67663 Kaiserslautern (Germany); Bram, Martin, E-mail: m.bram@fz-juelich.de [Forschungszentrum Jülich, Institute of Energy and Climate Research (IEK), 52425 Jülich (Germany)

    2016-03-01

    Porous titanium cylinders were produced with a constant amount of temporary space holder (70 vol.%). Different interstitial contents were achieved by varying the starting powders (HDH vs. gas atomized) and manufacturing method (cold compaction without organic binders vs. warm compaction of MIM feedstocks). Interstitial contents (O, C, and N) as a function of manufacturing were measured by chemical analysis. Samples contained 0.34–0.58 wt.% oxygen, which was found to have the greatest effect on mechanical properties. Quasi-static mechanical tests under compression at low strain rate were used for reference and to define parameters for cyclic compression tests. Not unexpectedly, increased oxygen content increased the yield strength of the porous titanium. Cyclic compression fatigue tests were conducted using sinusoidal loading in a servo-hydraulic testing machine. Increased oxygen content was concomitant with embrittlement of the titanium matrix, resulting in significant reduction of compression cycles before failure. For samples with 0.34 wt.% oxygen, R, σ{sub min} and σ{sub max} were varied systematically to estimate the fatigue limit (~ 4 million cycles). Microstructural changes induced by cyclic loading were then characterized by optical microscopy, SEM and EBSD. - Highlights: • Systematic variation of the oxygen content from 0.34 to 0.58 wt.%. • Systematic study of the relationship between fatigue limit and oxygen content. • Critical oxygen equivalent seems to be 0.35 wt.% to avoid embrittlement. • Identification of the failure modes by light microscopy, SEM and EBSD.

  7. Qualitative Content Analysis

    Directory of Open Access Journals (Sweden)

    Satu Elo

    2014-02-01

    Full Text Available Qualitative content analysis is commonly used for analyzing qualitative data. However, few articles have examined the trustworthiness of its use in nursing science studies. The trustworthiness of qualitative content analysis is often presented by using terms such as credibility, dependability, conformability, transferability, and authenticity. This article focuses on trustworthiness based on a review of previous studies, our own experiences, and methodological textbooks. Trustworthiness was described for the main qualitative content analysis phases from data collection to reporting of the results. We concluded that it is important to scrutinize the trustworthiness of every phase of the analysis process, including the preparation, organization, and reporting of results. Together, these phases should give a reader a clear indication of the overall trustworthiness of the study. Based on our findings, we compiled a checklist for researchers attempting to improve the trustworthiness of a content analysis study. The discussion in this article helps to clarify how content analysis should be reported in a valid and understandable manner, which would be of particular benefit to reviewers of scientific articles. Furthermore, we discuss that it is often difficult to evaluate the trustworthiness of qualitative content analysis studies because of defective data collection method description and/or analysis description.

  8. Performance of Separation Processes for Precipitated Calcium Carbonate Produced with an Innovative Method from Steelmaking Slag and Carbon Dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Teir, Sebastian, E-mail: sebastian.teir@vtt.fi [VTT Technical Research Centre of Finland Ltd., Espoo (Finland); Auvinen, Toni [Outotec Dewatering Technology Center, Lappeenranta (Finland); Said, Arshe [Department of Energy Technology, School of Engineering, Aalto University, Espoo (Finland); Kotiranta, Tuukka; Peltola, Heljä [Outotec Research Center, Pori (Finland)

    2016-02-22

    In this work, experiments were performed to determine the filterability of calcium carbonate produced with an alternative calcium carbonate production concept. The concept uses steelmaking slag as raw material and has potential to fix CO{sub 2} emissions and utilize steelmaking slag, simultaneously. As calcium carbonate is precipitated in a solution containing ammonium chloride, calcium chloride, and ammonia, the product needs to be washed and hence filtered. In this work, different separation processes, including washing, filtering, and drying, were tested on two calcium carbonate slurries produced from steel converter slag and CO{sub 2} by a laboratory-scale pilot facility, with the aim of obtaining a solid product with a low chloride content using a minimum amount of washing water. The order of maximum filtration rates achievable of the calcium carbonate slurries was determined by experimental work. The tests included pressure filtration and vacuum filtration and the test series contained altogether 21 different filtration cycles with varying combinations of filtering, washing, and drying steps. The filtered cakes were analyzed by their residual moisture content, chloride content, and conductivity, and the filtrates by their residual solids content, chloride content, and conductivity. Pressure filtration gave a high capacity (400–460 kg/m{sup 2}h) and a low cake residual moisture content (12–14 wt-%). Vacuum filtration gave slightly higher filtration rates (500–610 kg/m{sup 2}h at the lowest residual chloride contents of the cakes), but the cake residual moisture also stayed higher (25–26 wt-%). As the vacuum filtration tests used a filter cloth with higher permeability than that of the pressure filtration tests, a slightly higher filtration rate was expected. However, both filtration technologies seem suitable for filtering and washing calcium carbonate prepared with the studied method as a residual chloride content as low as 10 ppm of the filtered

  9. Fatigue behavior of highly porous titanium produced by powder metallurgy with temporary space holders.

    Science.gov (United States)

    Özbilen, Sedat; Liebert, Daniela; Beck, Tilmann; Bram, Martin

    2016-03-01

    Porous titanium cylinders were produced with a constant amount of temporary space holder (70 vol.%). Different interstitial contents were achieved by varying the starting powders (HDH vs. gas atomized) and manufacturing method (cold compaction without organic binders vs. warm compaction of MIM feedstocks). Interstitial contents (O, C, and N) as a function of manufacturing were measured by chemical analysis. Samples contained 0.34-0.58 wt.% oxygen, which was found to have the greatest effect on mechanical properties. Quasi-static mechanical tests under compression at low strain rate were used for reference and to define parameters for cyclic compression tests. Not unexpectedly, increased oxygen content increased the yield strength of the porous titanium. Cyclic compression fatigue tests were conducted using sinusoidal loading in a servo-hydraulic testing machine. Increased oxygen content was concomitant with embrittlement of the titanium matrix, resulting in significant reduction of compression cycles before failure. For samples with 0.34 wt.% oxygen, R, σ(min) and σ(max) were varied systematically to estimate the fatigue limit (~4 million cycles). Microstructural changes induced by cyclic loading were then characterized by optical microscopy, SEM and EBSD. Copyright © 2015 Elsevier B.V. All rights reserved.

  10. Free-range farming: a natural alternative to produce vitamin D-enriched eggs.

    Science.gov (United States)

    Kühn, Julia; Schutkowski, Alexandra; Kluge, Holger; Hirche, Frank; Stangl, Gabriele I

    2014-04-01

    Food-based strategies need to be developed to improve the vitamin D status of individuals. Recent studies identified ultraviolet B irradiation as an efficient method to enrich mushrooms and eggs with vitamin D. The aim of this study was to determine whether free-range farming of hens could provide a valuable method to produce vitamin D-enriched eggs. Laying hens were randomly assigned to three groups of 33 to 34 animals each, and were kept either indoors (indoor group), outdoors (outdoor group), or with an indoor/outdoor option (indoor/outdoor group) over 4 wk. The study shows that the vitamin D3 content of egg yolk was three- to fourfold higher in the groups that were exposed to sunlight (outdoor and indoor/outdoor groups) compared with the indoor group (P Egg yolk from the outdoor group revealed the highest vitamin D3 content, which averaged 14.3 μg/100 g dry matter (DM), followed by that from the indoor/outdoor group (11.3 μg/100 g DM). Yolk from indoor eggs contained only 3.8 μg vitamin D/100 g DM. The 25-hydroxyvitamin D (25[OH]D3) content of egg yolk was also influenced by sunlight exposure, although less pronounced than the vitamin D content (P eggs randomly acquired from supermarkets had relatively low vitamin D contents. Free-range farming offers an efficient alternative to fortify eggs with vitamin D, provided that farming conditions are sufficiently attractive for hens to range outside. Copyright © 2014 Elsevier Inc. All rights reserved.

  11. Pancreatic size and fat content in diabetes: A systematic review and meta-analysis of imaging studies.

    Directory of Open Access Journals (Sweden)

    Tiago Severo Garcia

    Full Text Available Imaging studies are expected to produce reliable information regarding the size and fat content of the pancreas. However, the available studies have produced inconclusive results. The aim of this study was to perform a systematic review and meta-analysis of imaging studies assessing pancreas size and fat content in patients with type 1 diabetes (T1DM and type 2 diabetes (T2DM.Medline and Embase databases were performed. Studies evaluating pancreatic size (diameter, area or volume and/or fat content by ultrasound, computed tomography, or magnetic resonance imaging in patients with T1DM and/or T2DM as compared to healthy controls were selected. Seventeen studies including 3,403 subjects (284 T1DM patients, 1,139 T2DM patients, and 1,980 control subjects were selected for meta-analyses. Pancreas diameter, area, volume, density, and fat percentage were evaluated.Pancreatic volume was reduced in T1DM and T2DM vs. controls (T1DM vs. controls: -38.72 cm3, 95%CI: -52.25 to -25.19, I2 = 70.2%, p for heterogeneity = 0.018; and T2DM vs. controls: -12.18 cm3, 95%CI: -19.1 to -5.25, I2 = 79.3%, p for heterogeneity = 0.001. Fat content was higher in T2DM vs. controls (+2.73%, 95%CI 0.55 to 4.91, I2 = 82.0%, p for heterogeneity<0.001.Individuals with T1DM and T2DM have reduced pancreas size in comparison with control subjects. Patients with T2DM have increased pancreatic fat content.

  12. Connecting the Dots Downunder Towards An Integrated Institutional Approach To Digital Content Management

    CERN Document Server

    Harboe-Ree, Cathrine

    2004-01-01

    There is a growing interest among academic institutions in managing institutional digital content produced in and for research, teaching and learning. This article argues for an integrated approach to this activity and examines the role of libraries in facilitating this. It then considers some existing approaches to providing software to support this. Australian initiatives consistent with this integrated model are then discussed.

  13. Effect of test meals of varying dietary fiber content on plasma insulin and glucose response.

    Science.gov (United States)

    Potter, J G; Coffman, K P; Reid, R L; Krall, J M; Albrink, M J

    1981-03-01

    To assess the effect of dietary fiber on glucose tolerance four different meals of varying fiber content but identical protein fat and carbohydrate content were fed to eight healthy men aged 22 to 45. Each meal provided 75 g of carbohydrate as liquid glucose formula, as brown rice, pinto beans, or All Bran. The mean plasma glucose and insulin responses were highest following the formula, and least for All Bran and pinto beans. Rice produced nearly as great a rise in insulin and glucose as did the formula. The rank of each meal by content of neutral detergent fiber was nearly the inverse of the rank by magnitude of the insulin response evoked, fiber content being greatest in All Bran (18 g) and pinto beans (16.2 g), low in rice (2.8 g) and absent from the formula. It was concluded that dietary fiber dampened the insulin response to a high carbohydrate meal.

  14. Enhancement of lipid accumulation by oleaginous yeast through phosphorus limitation under high content of ammonia.

    Science.gov (United States)

    Huang, Xiangfeng; Luo, Huijuan; Mu, Tianshuai; Shen, Yi; Yuan, Ming; Liu, Jia

    2018-04-18

    Low concentrations of acetic acid were used as carbon source to cultivate Cryptococcus curvatus MUCL 29819 for lipid production under high content of ammonia. Phosphorus limitation combined with initial pH regulation (pH = 6) weakened inhibition of free ammonia and promoted lipid accumulation. In batch cultivation, the produced lipid content and yield was 30.3% and 0.92 g/L, higher than those under unlimited condition (18.3% and 0.64 g/L). The content of monounsaturated fatty acid also increased from 37.3% (unlimited condition) to 45.8% (phosphorus-limited condition). During sequencing batch cultivation (SBC), the lipid content reached up to 51.02% under phosphorus-limited condition while only 31.88% under unlimited condition, which can be explained by the higher conversion efficiency of the carbon source to lipid. The total energy consumption including lipid extraction, transesterification and purification was 7.47 and 8.33 GJ under phosphorus-limited and unlimited condition, respectively. Copyright © 2018. Published by Elsevier Ltd.

  15. A Comparison of Producer Gas, Biochar, and Activated Carbon from Two Distributed Scale Thermochemical Conversion Systems Used to Process Forest Biomass

    Directory of Open Access Journals (Sweden)

    Nathaniel Anderson

    2013-01-01

    Full Text Available Thermochemical biomass conversion systems have the potential to produce heat, power, fuels and other products from forest biomass at distributed scales that meet the needs of some forest industry facilities. However, many of these systems have not been deployed in this sector and the products they produce from forest biomass have not been adequately described or characterized with regards to chemical properties, possible uses, and markets. This paper characterizes the producer gas, biochar, and activated carbon of a 700 kg h−1 prototype gasification system and a 225 kg h−1 pyrolysis system used to process coniferous sawmill and forest residues. Producer gas from sawmill residues processed with the gasifier had higher energy content than gas from forest residues, with averages of 12.4 MJ m−3 and 9.8 MJ m−3, respectively. Gases from the pyrolysis system averaged 1.3 MJ m−3 for mill residues and 2.5 MJ m−3 for forest residues. Biochars produced have similar particle size distributions and bulk density, but vary in pH and carbon content. Biochars from both systems were successfully activated using steam activation, with resulting BET surface area in the range of commercial activated carbon. Results are discussed in the context of co-locating these systems with forest industry operations.

  16. Exploring Oven-drying Technique in Producing Pineapple Powder

    Directory of Open Access Journals (Sweden)

    Cyril John A. Domingo

    2017-11-01

    Full Text Available Pineapple puree and juice of 11 to 12 °Brix were used to obtain pineapple powder using oven-drying technique. Addition of maltodextrin in treatments 2 and 4 yielded good quality powder, however addition of sugar and maltodextrin in treatments 1 and 3 resulted to sticky product which was processed to pineapple leather. Treatment 2 composed of pineapple puree and maltodextrin resulted to significantly higher powder recovery compared with treatment 4 which composed of pineapple juice and maltodextrin. The solubility of pineapple powder improved as maltodextrin concentration is increased from 40.00 % to 60.00 %.Addition of maltodextrin also reduced stickiness of the final product. An instant pineapple powder of 5.47 and 5.33 % moisture content could be produced by oven-drying.This level of moisture content will prohibit bacterial growth in the pineapple powder but may have mold or yeast growth with increase storage period at environments with high humidity. Molds were observed on the 17th day at 89.00 % relative humidity as exhibited by the moisture sorption isotherm data. This suggests that appropriate packaging with moisture barrier is recommended for pineapple powder. This study showedthat by using appropriate ratio of juice, puree, and maltodextrin and appropriate oven drying conditions, a good oven-dried pineapple powder could be obtained.

  17. Structure of branching enzyme- and amylomaltase modified starch produced from well-defined amylose to amylopectin substrates

    DEFF Research Database (Denmark)

    Sorndecha, Waraporn; Sagnelli, Domenico; Meier, Sebastian

    2016-01-01

    by the molar mass rather that the branching density of the glucan per se . Our data demonstrate that a higher amylose content in the substrate starch efficiently produces α-1,6 glucosidic linkages and that the present of amylose generates a higher Μw and more resistant product than amylopectin. The combination...

  18. Wikipedia Culture Gap: Quantifying Content Imbalances Across 40 Language Editions

    Directory of Open Access Journals (Sweden)

    Marc Miquel-Ribé

    2018-06-01

    Full Text Available The online encyclopedia Wikipedia is the largest general information repository created through collaborative efforts from all over the globe. Despite the project's goal being to achieve the sum of human knowledge, there are strong content imbalances across the language editions. In order to quantify and investigate these imbalances, we study the impact of cultural context in 40 language editions. To this purpose, we developed a computational method to identify articles that can be related to the editors' cultural context associated to each Wikipedia language edition. We employed a combination of strategies taking into account geolocated articles, specific keywords and categories, as well as links between articles. We verified the method's quality with manual assessment and found an average precision of 0.92 and an average recall of 0.95. The results show that about a quarter of each Wikipedia language edition is dedicated to represent the corresponding cultural context. Although a considerable part of this content was created during the first years of the project, its creation is sustained over time. An analysis of cross-language coverage of this content shows that most of it is unique in its original language, and reveals special links between cultural contexts; at the same time, it highlights gaps where the encyclopedia could extend its content. The approach and findings presented in this study can help to foster participation and inter-cultural enrichment of Wikipedias. The datasets produced are made available for further research.

  19. Understanding human quality judgment in assessing online forum contents for thread retrieval purpose

    Science.gov (United States)

    Ismail, Zuriati; Salim, Naomie; Huspi, Sharin Hazlin

    2017-10-01

    Compared to traditional materials or journals, user-generated contents are not peer-reviewed. Lack of quality control and the explosive growth of web contents make the task of finding quality information on the web especially critical. The existence of new facilities for producing web contents such as forum makes this issue more significant. This study focuses on online forums threads or discussion, where the forums contain valuable human-generated information in a form of discussions. Due to the unique structure of the online forum pages, special techniques are required to organize and search for information in these forums. Quality biased retrieval is a retrieval approach that search for relevant document and prioritized higher quality documents. Despite major concern of quality content and recent development of quality biased retrieval, there is an urgent need to understand how quality content is being judged, for retrieval and performance evaluation purposes. Furthermore, even though there are various studies on the quality of information, there is no standard framework that has been established. The primary aim of this paper is to contribute to the understanding of human quality judgment in assessing online forum contents. The foundation of this study is to compare and evaluate different frameworks (for quality biased retrieval and information quality). This led to the finding that many quality dimensions are redundant and some dimensions are understood differently between different studies. We conducted a survey on crowdsourcing community to measure the importance of each quality dimensions found in various frameworks. Accuracy and ease of understanding are among top important dimensions while threads popularity and contents manipulability are among least important dimensions. This finding is beneficial in evaluating contents of online forum.

  20. A combination of additives can synergically decrease acrylamide content in gingerbread without compromising sensory quality.

    Science.gov (United States)

    Komprda, Tomáš; Pridal, Antonin; Mikulíková, Renata; Svoboda, Zdeněk; Cwiková, Olga; Nedomová, Šárka; Sýkora, Vladimír

    2017-02-01

    The present study tested whether replacement of the leavening agent ammonium carbonate by sodium hydrogen carbonate in combination with calcium cation and acidifying agent will synergically decrease acrylamide (AA) content in gingerbread. The type of leavening agent and the presence of Ca 2+ and citric acid accounted for 33.6%, 13.2% and 53.2% of the explained variability of the AA content, respectively (P sensory analysis did not indicate any significant deterioration (P > 0.05) in the organoleptic quality of gingerbread produced using calcium cation and citric acid. The present study demonstrates that the combination of additives NaHCO 3 /Ca 2+ /citric acid synergically decreases AA content in gingerbread without compromising the sensory quality. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  1. Scale-up fermentation of oil palm empty fruit bunch to produce ruminant feed by radiation processing

    International Nuclear Information System (INIS)

    Awang, M.R.; Mutaat, H.H.; Deres, R.M.; Kume, Tamikazu.

    1992-01-01

    Scale-up fermentation and irradiation conditions of empty fruit bunch (EFB) of oil palm were examined to produce a large amount of fermented products for animal feeds. The EFB substrates pasteurized by irradiation were inoculated with Coprinus cinereus. After 1 month incubation, the crude fiber contents decreased to 20 - 38% and crude protein contents increased to 9 - 13% in small scale fermentation using conical flask (6 - 20 g EFB). In the case of fermentation using polypropylene bags with 400 g EFB, crude fiber and protein contents were 32 - 34% and 11 - 14%, respectively. A larger plastic container packed with 1.5 kg EFB fiber of 10cm thickness was used for mushroom cultivation. After harvest of mushroom (yields were about 250 g per container), the quality of residual substrates improved further as reflected by its crude fiber content of only 16 - 20%, crude protein content of 6 - 8%. These results show that a large volume of products are available under the good aeration by increasing the number of plastic bags or containers. For the irradiation of a lot of fermentation substrates, the advantage of 60 Co gamma-ray and electron beam irradiator was also discussed. (author)

  2. The economic impact of strengthening fuel quality regulation-reducing sulfur content in diesel fuel

    International Nuclear Information System (INIS)

    Chang, H.J.; Cho, G.L.; Kim, Y.D.

    2006-01-01

    This paper investigates the impact of strengthening vehicle emission regulation on economic activities. The government attempts to use three regulation measures to protect air quality from transportation emission. The measures include the aggregate limit (bubbles), the vehicle emission standard, and the fuel quality standard. Especially, we focus on the economic impact of reducing sulfur content in diesel fuel quality standard. Sulfur content in diesel fuel is one of the main factors in worsening local air quality. The emission from diesel vehicle accounts for 51.8% of total vehicle emission in Korea. If sulfur content reduction regulation is implemented, then the petroleum industry should build more facility to produce low sulfur content diesel, leading to additional production costs and increasing prices and decreasing outputs. We use computable general equilibrium model to analyze how the sulfur reduction regulation affects economic activities and trace out local emission reduction cost and GDP loss. And we suggest the tax-recycling mechanism to mitigate the negative economic costs due to the sulfur reduction regulation

  3. Improvement of cassava for high dry matter, starch and low cyanogenic glucoside content by mutation induction

    Energy Technology Data Exchange (ETDEWEB)

    Nwachukwu, E C; Mbanaso, E N.A.; Ene, L S.O. [Plant Breeding Div., National Root Crops Research Inst., Umudike, Umuahia (Nigeria)

    1997-07-01

    Cassava (Manihot esculenta Crantz) is an important food in Nigeria. One drawback in its use as a staple food is the presence of cyanogenic glucosides which on hydrolysis produce the very toxic hydrogen cyanide (HCN). To reduce the cyanogenic levels by mutation induction, three locally adopted and high yielding varieties of cassava, TMS 30572, NR 8817 and NR 84111 were irradiated with 20, 25 and 30 Gy gamma rays. There were a wide variation in HCN, dry matter and starch content of irradiated cassava plants, screened in the MV{sub 2} propagation. Fourteen cassavavariant lines were selected for low HCN content, and 22 lines for high dry matter content. These will be further tested for yield in replicated field trials. (author). 7 refs, 3 tabs.

  4. Effects of waste content of glass waste forms on Savannah River high-level waste disposal costs

    International Nuclear Information System (INIS)

    McDonell, W.R.; Jantzen, C.M.

    1985-01-01

    Effects of the waste content of glass waste forms of Savannah River high-level waste disposal costs are evaluated by their impact on the number of waste canisters produced. Changes in waste content affect onsite Defense Waste Processing Facility (DWPF) costs as well as offsite shipping and repository emplacement charges. A nominal 1% increase over the 28 wt % waste loading of DWPF glass would reduce disposal costs by about $50 million for Savannah River wastes generated to the year 2000. Waste form modifications under current study include adjustments of glass frit content to compensate for added salt decontamination residues and increased sludge loadings in the DWPF glass. Projected cost reductions demonstrate significant incentives for continued optimization of the glass waste loadings. 13 refs., 3 figs., 3 tabs

  5. Improvement of cassava for high dry matter, starch and low cyanogenic glucoside content by mutation induction

    International Nuclear Information System (INIS)

    Nwachukwu, E.C.; Mbanaso, E.N.A.; Ene, L.S.O.

    1997-01-01

    Cassava (Manihot esculenta Crantz) is an important food in Nigeria. One drawback in its use as a staple food is the presence of cyanogenic glucosides which on hydrolysis produce the very toxic hydrogen cyanide (HCN). To reduce the cyanogenic levels by mutation induction, three locally adopted and high yielding varieties of cassava, TMS 30572, NR 8817 and NR 84111 were irradiated with 20, 25 and 30 Gy gamma rays. There were a wide variation in HCN, dry matter and starch content of irradiated cassava plants, screened in the MV 2 propagation. Fourteen cassavavariant lines were selected for low HCN content, and 22 lines for high dry matter content. These will be further tested for yield in replicated field trials. (author). 7 refs, 3 tabs

  6. Study of new compounds for their application on free radicals EPR dosimetry

    International Nuclear Information System (INIS)

    Condes N, C.S.

    1996-01-01

    L- α alanine is an amino acid which has been used for electron and γ ray dosimetric purposes, when crystallites of L-α alanine are irradiated with ionizing radiation free radicals are produced. The yield of free radicals produced by irradiation of alanine crystals can be evaluated by EPR spectrometry, however when L- α alanine crystals are irradiated with thermal neutrons the yield of the free radicals produced is very low and in consequence it's EPR-signal response is poor. In this work we mixed L-α alanine together with some lithium compounds such as LiF, LiBO 2 , LiOH and Li 2 CO 3 . In this way when we irradiate the respective mixture of alanine-lithium with thermal neutrons, the nuclear reactions 6 Li (n,α)T and 10 B (n, α) 7 Li can be produced with a high probability. As a consequence α particles and recoil atoms emerging from the nuclear reactions can impinge on alanine molecules, producing extra free radicals. From the alanine-lithium mixtures obtained, we made dosemeters (30 mm long., 3.9 mm diameter) which were irradiated in the thermal column of the TRIGA Mark III Nuclear Reactor with a flux of thermal neutrons of 5 x 10 7 n/ cm 2 s. Irradiations were made at different periods. Experimental evaluations indicate that the mixtures can be used for dosimetric purposes. (Author)

  7. Fumonisin contamination and fumonisin producing black Aspergilli in dried vine fruits of different origin.

    Science.gov (United States)

    Varga, J; Kocsubé, S; Suri, K; Szigeti, Gy; Szekeres, A; Varga, M; Tóth, B; Bartók, T

    2010-10-15

    Aspergillus niger isolates are able to produce fumonisins in high quantities on agar media with a low water activity. Several agricultural products fit this criterion, including dried vine fruits, dates and figs. Data on the occurrence and role of this species in fumonisin contamination of agricultural products with high sugar content are needed to clarify the importance of A. niger in human health. The mycobiota and fumonisin contamination of various dried vine fruit samples collected from different countries were examined to clarify the role of black Aspergilli in fumonisin contamination of such products. All except two of the examined samples were contaminated with black Aspergilli. Species assignment of the isolates was carried out using sequence analysis of part of the calmodulin gene. The range of fumonisin isomers present in the raisins samples, and produced by A. niger isolates collected from dried vine fruits was also examined using reversed-phase high-performance liquid chromatography/electrospray ionization-ion trap mass spectrometry (RP-HPLC/ESI-ITMS). Among the 30 A. niger/A. awamori isolates identified, 20 were found to be able to produce fumonisins (average contamination: 5.16 mg/kg; range: 0.017-19.6 mg/kg). The average fumonisin content of the 7 dried vine fruit samples which were found to be contaminated by potential fumonisin producing black Aspergilli was 7.22 mg/kg (range: 4.55-35.49 mg/kg). The isolates produced several fumonisin isomers also present in the dried vine fruit samples, including fumonisins B(1-4), 3-epi-FB(3), 3-epi-FB(4), iso-FB(1), and two iso-FB(2,3) forms. Fumonisin B(1) was detected for the first time in A. niger cultures. Most of these isomers have previously only been identified in Fusarium species. Our data indicate that A. niger and A. awamori are responsible for fumonisin contamination of dried vine fruits worldwide. The observed levels of contamination are alarming and pose a new threat for food safety. Copyright

  8. Detection of Isoflavones Content in Soybean Based on Hyperspectral Imaging Technology

    Directory of Open Access Journals (Sweden)

    Tan Kezhu

    2014-04-01

    Full Text Available Because of many important biological activities, Soybean isoflavones which has great potential for exploitation is significant to practical applications. Due to the conventional methods for determination of soybean isoflavones having long detection period, used too many reagents, couldn’t be detected on-line, and other issues, we propose hyperspectral imaging technology to detect the contents of soybean isoflavones. Based on the 40 varieties of soybeans produced in Heilongjiang province, we get the spectral reflection datum of soybean samples varied from the soybean’s hyperspectral images which are collected by the hyperspectral imaging system, and apply high performance liquid chromatography (HPLC method to determine the true value of the selected samples of isoflavones. The feature wavelengths for isoflavones content prediction (1516, 1572, 1691, 1716 and 1760 nm were selected based on correlation analysis. The prediction model was established by using the method of BP neural network in order to realize the prediction of soybean isoflavones content analysis. The experimental results show that, the ANN model could predict isoflavones content of soybean samples with of 0.9679, the average relative error is 0.8032 %, and the mean square error (MSE is 0.110328, which indicates the effectiveness of the proposed method and provides a theoretical basis for the applications of hyerspectral imaging in non-destructive detection for interior quality of soybean.

  9. Metal Content and Stable Isotope Determination in Some Commercial Beers from Romanian Markets

    Directory of Open Access Journals (Sweden)

    Cezara Voica

    2015-01-01

    Full Text Available Characterization of beer samples is of interest because their compositions affect the taste and stability of beer and, also, consumer health. In this work, the characterizations of 20 Romanian beers were performed by mean of Inductively Coupled Plasma Mass Spectrometry (ICP-MS and Isotope Ratio Mass Spectrometry (IRMS in order to trace heavy metals and isotopic content of them. Major, minor, and trace metals are important in beer fermentation since they supply the appropriate environment for yeast growth and influence yeast metabolism. Beside this, the presence of the C4 plants in the brewing process was followed. Our study has shown that the analyzed beers indicated the presence of different plant types used in brewing: C3, C3-C4 mixtures, and also C4, depending on producers. Also the trace metal content of each sample is presented and discussed in this study. A comparison of the beers quality manufactured by the same producer but bottled in different type of packaging like glass, dose, or PET was made; our results show that no compositional differences among the same beer type exist.

  10. Dream content and intrusive thoughts in Obsessive-Compulsive Disorder.

    Science.gov (United States)

    Cavallotti, Simone; Casetta, Cecilia; Fanti, Valentina; Gambini, Orsola; Ostinelli, Edoardo G; Ranieri, Rebecca; Vanelli, Irene; D'Agostino, Armando

    2016-10-30

    Although central to any exhaustive theory of human subjectivity, the relationship between dream and waking consciousness remains uncertain. Some findings suggest that dream consciousness can be influenced by severe disorders of thought content. The suppression of unwanted thoughts has been shown to influence dream content in healthy individuals. In order to better define this phenomenon, we evaluated the persistence of obsessive/compulsive themes across the dream and waking cognition of OCD patients and in a control group of healthy subjects. Participants were administered a shortened version of the Thematic Apperception Test to produce a waking fantasy narration, and were trained to keep a dream diary. Dream and waking narrative contents were analyzed in order to recognize obsessive/compulsive themes, and to calculate Mean Dream Obsession/Compulsion (MDO, MDC) and Mean TAT Obsession/Compulsion (MTO, MTC) parameters. No differences were found between the two populations in terms of MDO, MDC, MTO, nor MTC. Density of obsessive and compulsive themes were significantly higher in dream reports than in waking narratives for both groups. No correlation was observed between MDO/MDC scores and Y-BOCS obsession/compulsion scores in the OCD group. These findings strengthen the discontinuity hypothesis, suggesting that ruminative aspects of cognition are somehow interrupted during dream activity. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  11. Wide-scale utilization of MSWI fly ashes in cement production and its impact on average heavy metal contents in cements: The case of Austria.

    Science.gov (United States)

    Lederer, Jakob; Trinkel, Verena; Fellner, Johann

    2017-02-01

    A number of studies present the utilization of fly ashes from municipal solid waste incineration (MSWI) in cement production as a recycling alternative to landfilling. While there is a lot of research on the impact of MSWI fly ashes utilization in cement production on the quality of concrete or the leaching of heavy metals, only a few studies have determined the resulting heavy metal content in cements caused by this MSWI fly ashes utilization. Making use of the case of Austria, this study (1) determines the total content of selected heavy metals in cements currently produced in the country, (2) designs a scenario and calculates the resulting heavy metal contents in cements assuming that all MSWI fly ashes from Austrian grate incinerators were used as secondary raw materials for Portland cement clinker production and (3) evaluates the legal recyclability of demolished concretes produced from MSWI fly ash amended cements based on their total heavy metal contents. To do so, data from literature and statistics are combined in a material flow analysis model to calculate the average total contents of heavy metals in cements and in the resulting concretes according to the above scenario. The resulting heavy metal contents are then compared (i) to their respective limit values for cements as defined in a new technical guideline in Austria (BMLFUW, 2016), and (ii) to their respective limit values for recycling materials from demolished concrete. Results show that MSWI fly ashes utilization increases the raw material input in cement production by only +0.9%, but the total contents of Cd by +310%, and Hg, Pb, and Zn by +70% to +170%. However these and other heavy metal contents are still below their respective limit values for Austrian cements. The same legal conformity counts for recycling material derived from concretes produced from the MSWI fly ash cements. However, if the MSWI fly ash ratio in all raw materials used for cement production were increased from 0.9% to 22

  12. Co-production of bio-oil and propylene through the hydrothermal liquefaction of polyhydroxybutyrate producing cyanobacteria.

    Science.gov (United States)

    Wagner, Jonathan; Bransgrove, Rachel; Beacham, Tracey A; Allen, Michael J; Meixner, Katharina; Drosg, Bernhard; Ting, Valeska P; Chuck, Christopher J

    2016-05-01

    A polyhydroxybutyrate (PHB) producing cyanobacteria was converted through hydrothermal liquefaction (HTL) into propylene and a bio-oil suitable for advanced biofuel production. HTL of model compounds demonstrated that in contrast to proteins and carbohydrates, no synergistic effects were detected when converting PHB in the presence of algae. Subsequently, Synechocystis cf. salina, which had accumulated 7.5wt% PHB was converted via HTL (15% dry weight loading, 340°C). The reaction gave an overall propylene yield of 2.6%, higher than that obtained from the model compounds, in addition to a bio-oil with a low nitrogen content of 4.6%. No propylene was recovered from the alternative non-PHB producing cyanobacterial strains screened, suggesting that PHB is the source of propylene. PHB producing microorganisms could therefore be used as a feedstock for a biorefinery to produce polypropylene and advanced biofuels, with the level of propylene being proportional to the accumulated amount of PHB. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Induced mutations in wheat, Triticum aestivum L., for high protein and lysine content

    International Nuclear Information System (INIS)

    Barriga, P.; Fuentes, R.

    1984-01-01

    With the aim of producing cultivars adapted to the Lakes Region of Chile (latitude 39-44 deg. South) with better protein content and high grain yield, in 1975 spring wheat seeds of genotypes Express and UACH-2-75 were irradiated with gamma rays in doses of 15, 25 and 35 Krad. The M 1 generation was field sown and harvested individually, initiating plant selection in the M 2 generation. The selection process, through six generations, has permitted to identify some mutants of high protein content. Two mutants UACH-2-I and UACH-3-I have been included in the National Co-operative Wheat Program for yield. A second experiment was initiated in 1981 with the objective of obtaining mutants not only for high protein content but also for high lysine content. For this purpose seeds of the spring wheat genotypes Huenufen and Austral were irradiated with gamma rays in doses of 10 and 25 Krad. The M 1 generation was sown at a high density and harvested in bulk. Selection per plant will start in the M 2 generation, continuing in the following. (author)

  14. Mechanisms of mercury removal by biochars produced from different feedstocks determined using X-ray absorption spectroscopy

    International Nuclear Information System (INIS)

    Liu, Peng; Ptacek, Carol J.; Blowes, David W.; Landis, Richard C.

    2016-01-01

    Highlights: • Dissolved Hg decreases by >90% with high-T biochars (600 and 700 °C). • Elevated SO 4 2− (up to 1000 mg L −1 ) is released from manure-derived biochar. • XRF results indicate Hg is distributed heterogeneously throughout biochar particles. • S XANES indicates presence of reduced and oxidized S species in biochar. • Hg EXAFS indicate Hg is bound to S atoms in biochar particle when S content is high. - Abstract: Thirty-six biochars produced from distinct feedstocks at different temperatures were evaluated for their potential to remove mercury (Hg) from aqueous solution at environmentally relevant concentrations. Concentrations of total Hg (THg) decreased by >90% in batch systems containing biochars produced at 600 and 700 °C and by 40–90% for biochars produced at 300 °C. Elevated concentrations of SO 4 2− (up to 1000 mg L −1 ) were observed in solutions mixed with manure-based biochars. Sulfur X-ray absorption near edge structure (XANES) analyses indicate the presence of both reduced and oxidized S species in both unwashed and washed biochars. Sulfur XANES spectra obtained from biochars with adsorbed Hg were similar to those of washed biochars. Micro-X-ray fluorescence mapping results indicate that Hg was heterogeneously distributed across biochar particles. Extended X-ray absorption fine structure modeling indicates Hg was bound to S in biochars with high S content and to O and Cl in biochars with low S content. The predominant mechanisms of Hg removal are likely the formation of chemical bonds between Hg and various functional groups on the biochar. This investigation provides information on the effectiveness and mechanisms of Hg removal that is critical for evaluating biochar applications for stabilization of Hg in surface water, groundwater, soils, and sediments.

  15. Mechanisms of mercury removal by biochars produced from different feedstocks determined using X-ray absorption spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Peng [Department of Earth and Environmental Sciences, University of Waterloo, 200 University Ave. W., Waterloo, ON N2L 3G1 (Canada); Ptacek, Carol J., E-mail: ptacek@uwaterloo.ca [Department of Earth and Environmental Sciences, University of Waterloo, 200 University Ave. W., Waterloo, ON N2L 3G1 (Canada); Blowes, David W. [Department of Earth and Environmental Sciences, University of Waterloo, 200 University Ave. W., Waterloo, ON N2L 3G1 (Canada); Landis, Richard C. [E I. du Pont de Nemours and Company, 974 Centre Road, Wilmington, DE 19805 (United States)

    2016-05-05

    Highlights: • Dissolved Hg decreases by >90% with high-T biochars (600 and 700 °C). • Elevated SO{sub 4}{sup 2−} (up to 1000 mg L{sup −1}) is released from manure-derived biochar. • XRF results indicate Hg is distributed heterogeneously throughout biochar particles. • S XANES indicates presence of reduced and oxidized S species in biochar. • Hg EXAFS indicate Hg is bound to S atoms in biochar particle when S content is high. - Abstract: Thirty-six biochars produced from distinct feedstocks at different temperatures were evaluated for their potential to remove mercury (Hg) from aqueous solution at environmentally relevant concentrations. Concentrations of total Hg (THg) decreased by >90% in batch systems containing biochars produced at 600 and 700 °C and by 40–90% for biochars produced at 300 °C. Elevated concentrations of SO{sub 4}{sup 2−} (up to 1000 mg L{sup −1}) were observed in solutions mixed with manure-based biochars. Sulfur X-ray absorption near edge structure (XANES) analyses indicate the presence of both reduced and oxidized S species in both unwashed and washed biochars. Sulfur XANES spectra obtained from biochars with adsorbed Hg were similar to those of washed biochars. Micro-X-ray fluorescence mapping results indicate that Hg was heterogeneously distributed across biochar particles. Extended X-ray absorption fine structure modeling indicates Hg was bound to S in biochars with high S content and to O and Cl in biochars with low S content. The predominant mechanisms of Hg removal are likely the formation of chemical bonds between Hg and various functional groups on the biochar. This investigation provides information on the effectiveness and mechanisms of Hg removal that is critical for evaluating biochar applications for stabilization of Hg in surface water, groundwater, soils, and sediments.

  16. [Nutritional characterization of produced fish for human consumption in Bucaramanga, Colombia].

    Science.gov (United States)

    Perea, Aide; Gómez, Elieth; Mayorga, Yamile; Triana, Cora Yohanna

    2008-03-01

    This research involves the nutritional characterization of the most commonly cultivated fish in the region. The species under study were: Rainbow trout (Salmo gairdnerii), tilapia roja (Oreocliromis sp), cachama blanca (Piaractus brachypomus), bocachico (Prochilodus reticulatus magdalenae) and catfish (Pseudoplatystoma faciatum). A sea fish, coho Salmon (Oncorhynchus kisutch), was used as reference because it is the imported species most used in the region, and it also contains n-3 fatty acids. For each fish sample moisture, ash, protein content, total fat, minerals (iron, calcium and phosphorous) and a fatty acid profile were determined. Results show a total protein content in between 16.4 and 22.6 g/100 g fillet for fresh water fish. Total fat amounts for trout are the highest (8.1 g/100 g fillet), while catfish has the lowest fat content (0.4 g/100 g fillet). Trout was found to be the most important source of n-3 fatty acids (EPA+DHA) and phosphorous, with values ranging from 0.25% to 0.52%, and 250 to 346 mg/100 g fillet, respectively. Catfish and trout exhibited the highest iron content, with values ranging from 3 to 6mg/100 g fillet. Salmon, on the other hand, showed a high n-3 fatty acid content of 1.16% to 2.25%, when compared to fresh water fish. Calcium content is low in all species under scrutiny. Fresh water fish, other than trout, show no significant amount of n-3 fatty acids. However, all of them are a good source of protein. The obtained results allowed to determine the profile of oily acids of produced fish for human consumption in the region, demonstrating that the trout is the species with major quantity of oily acids n-3 specially DHA and of the minerals the phosphorus. Other species (kinds) catfish, bocachico, tilapia and cachama, are not a source of oily acids n-3, but they are an important source of protein.

  17. Effect of Mo contents on corrosion behaviors of welded duplex stainless steel

    Science.gov (United States)

    Bae, Seong Han; Lee, Hae Woo

    2013-05-01

    The corrosion behaviour and change of the phase fraction in welded 24Cr Duplex stainless steel was investigated for different chemical composition ranges of Mo contents. Filler metal was produced by fixing the contents of Cr, Ni, N, and Mn while adjusting the Mo content to 0.5, 1.4, 2.5, 3.5 wt%. The δ-ferrite fraction was observed to increase as the content of Mo increased. A polarisation test conducted in a salt solution, indicated the pitting corrosion potential increased continuously to 3.5 wt% Mo, while the corrosion potential changed most between 0.5 and 1.41 wt% Mo. The location of the pitting corrosion in 0.5 wt% Mo steel was randomly distributed, but it occurred selectively at the grain boundary between the γ- and δ-ferrite phases in 1.4, 2.5 and 3.5 wt% Mo steel. Energy dispersive X-ray spectroscopy mapping analysis showed that areas deficient in Cr, Mo, and Ni occurred around the grain boundary of the γ- and δ-ferrite phases. Non-metallic inclusions are thought to act as initiation points for the pitting corrosion that occurs in the salt solution initially as a result of the potential difference between the matrix structure and the incoherent inclusions.

  18. Geographical influences on content of 10-hydroxy-trans-2-decenoic acid in royal jelly in China.

    Science.gov (United States)

    Wei, Wen-Ting; Hu, Yuan-Qiang; Zheng, Huo-Qing; Cao, Lian-Fei; Hu, Fu-Liang; Hepburn, H Randall

    2013-10-01

    The content of 10-hydroxy-trans-2-decenoic acid (10-HDA), a marker compound in royal jelly (RJ), is the most important criterion in grading RJ for commercial trade and varies with its origin. To identify the effect of geographical origin on 10-HDA content in RJ, 138 samples were collected from 19 provinces of China (divided into three groups) produced by either Apis mellifera ligustica Spinola, 1806 or a hybrid of A. m. ligustica and Apis mellifera carnica Pollman, 1879 and analyzed for moisture, sugar, crude protein, ash, acid, and 10-HDA concentration. The results show that RJ from western China has a significantly higher 10-HDA level (2.01 +/- 0.05%) than those from northeastern (1.87 +/- 0.05%) and eastern (1.75 +/- 0.03%) China. RJ secreted by hybrid bees contained more 10-HDA (1.89 +/- 0.03%) than that secreted by A. m. ligustica (1.78 +/- 0.03%). The 10-HDA content of RJ produced during flowering of rape (Brassica campestris L.), lime (Tilia amurensis Ruprecht), and vitex (Vitex negundo L. variety heterophylla (Franch.) Rehder) was 1.92, 1.80, and 1.68%, respectively. The results would be helpful during the process of price determination of RJ by providing some basis of geographical, bee strain, and botanical information for commercial trade.

  19. Income Content of the World Coffee Exports Income Content of the World Coffee Exports

    Directory of Open Access Journals (Sweden)

    Orlando Monteiro da Silva

    2013-05-01

    Full Text Available Coffee is the most widely commercialized tropical product on the international market. The 2009/10 crop had an estimated value of $15.4 billion, with 93.4 million bags exported. According to the International Coffee Organization (ICO, 2011, the coffee sector employed  around 26 million people in 56 producing countries and over 100 exporting countries. But how would coffee products rank, in terms of income content, in relation to other commercialized products, and how have they evolved? To answer this question, the annual income content of 5,111 products exported by 167 countries from the period between 2000 and 2009, was calculated. Data from the UNCOMTRADE (2011, and “sophistication” indicators proposed by Hausmann and Rodrik (2003 who classify different products according to their productivity, were used. An emphasis was put on five coffee products (whole grain, roasted, decaffeinated, caffeinated, and soluble, showing the evolution of the number of exporting countries and of the “sophistication” index (income content, whose temporal variation was decomposed by the effects of competitiveness and income per capita changes. The results showed that non-roasted, non-decaffeinated, whole grain coffee is still the most commercialized product, but with the lowest income content of all coffee products, occupying the twenty-fourth worst position in terms of income content in 2009. The roasted, decaffeinated coffee presented the greatest income growth in the period, placing itself in the 3,309th position in 2009. The decomposition of the index showed that for coffee products with the most processing, the greatest cause of export sophistication growth was the Revealed Comparative Advantage effect. Products with the least amount of processing presented a loss in relative market share, with the addition of values to the production chain occurring outside those countries producing the raw materials.El café es el producto tropical m

  20. Air Permitting Implications of a Biorefinery Producing Raw Bio-Oil in Comparison with Producing Gasoline and Diesel Blendstocks

    Energy Technology Data Exchange (ETDEWEB)

    Bhatt, Arpit H [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhang, Yi Min [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-02-01

    A biorefinery, considered a chemical process plant under the Clean Air Act permitting program, could be classified as a major or minor source based on the size of the facility and magnitude of regulated pollutants emitted. Our previous analysis indicates that a biorefinery using fast pyrolysis conversion process to produce finished gasoline and diesel blendstocks with a capacity of processing 2,000 dry metric tons of biomass per day would likely be classified as a major source because several regulated pollutants (such as particulate matter, sulfur dioxide, nitrogen oxide) are estimated to exceed the 100 tons per year (tpy) major source threshold, applicable to chemical process plants. Being subject to a major source classification could pose additional challenges associated with obtaining an air permit in a timely manner before the biorefinery can start its construction. Recent developments propose an alternative approach to utilize bio-oil produced via the fast pyrolysis conversion process by shipping it to an existing petroleum refinery, where the raw bio-oil can be blended with petroleum-based feedstocks (e.g., vacuum gas oil) to produce gasoline and diesel blendstocks with renewable content. Without having to hydro-treat raw bio-oil, a biorefinery is likely to reduce its potential-to-emit to below the 100 tpy major source threshold, and therefore expedite its permitting process. We compare the PTE estimates for the two biorefinery designs with and without hydrotreating of bio-oils and examine the air permitting implications on potential air permit classification and discuss the best available control technology requirements for the major source biorefinery utilizing hydrotreating operation. Our analysis is expected to provide useful information to new biofuel project developers to identify opportunities to overcome challenges associated with air permitting.

  1. A Course Wiki: Challenges in Facilitating and Assessing Student-Generated Learning Content for the Humanities Classroom

    Science.gov (United States)

    Lazda-Cazers, Rasma

    2010-01-01

    New Web technology allows for the design of traditionally lecture-centered humanities courses by fostering active learning and engaging students as producers of learning content. The article presents the experiences with a student-generated wiki for a Germanic Mythology course. Evaluations indicated an overwhelmingly positive student experience…

  2. The Effect of a Ceramic Coating on Zr Alloys in Terms of Corrosion

    International Nuclear Information System (INIS)

    Kim, Kyung Tae; Park, Kwangheon; Park, Joo Young; Noh, Seonho

    2013-01-01

    It is very important to analyze fuel cladding mechanical properties. Polycarbosilane(PCS) is a special ceramic whose protection films inhibit oxidation chemical resistance and strength at high temperatures. The PCS coating was carried out under various reaction conditions. The results showed that the supercritical process tries to moderate oxidation conditions such as temperature, time, and solution amount. In this study, we used specimens of the types currently used in nuclear reactors(zry-4, zirlo), as well as their corresponding coating specimens (PCS, CrN and CrN + Tungsten), to conduct an oxidation analysis four type of conditions(water, LiOH, LiOH + Boron, and steam) over the course of a month. CrN coating layers were successfully formed with good protection on metal surface and without any defect. CrN coated specimen formed protective coating layers, inhibiting oxidized layers. However, both Zry-4 and Zirlo PCS coated specimens experience suddenly high oxidation rates in all kinds of conditions. As a result, the specimens supported the acceleration of oxidation by PCS

  3. Synthesis of Co-Al-Cl LDH by cathodic material reprocessing from cellular phone batteries

    Energy Technology Data Exchange (ETDEWEB)

    Amaral, Fabio Augusto do; Machado, Erica Oliveira; Freitas, Leonardo Luis de; Santana, Laiane Kalita; Canobre, Sheila Cristina, E-mail: fabioamaral@yahoo.com.br, E-mail: fabioamaral@iqufu.ufu.br [Universidade Federal de Uberlandia (UFU/LAETE), (Brazil). Inst. de Quimica. Lab. de Armazenamento de Energia e Tratamento de Efluente

    2014-08-15

    The aim of this paper was the recovering of the cathodic material from discarded lithium ion batteries for obtainment of the lamellar double hydroxides (LDHs) by the co-precipitation method at variable pH in HCl and H{sub 2}O{sub 2} 1:1 (v/v) acid solution containing Co and Al (extracted from cathodic material composed of LiCoO{sub 2} and aluminum foil). These metals were precipitated in LiOH at pH 9 or 11, or NH{sub 4}OH at pH 9 and submitted to the hydrothermal treatment (HT) to improve the structural organization of the LDHs lamellae. After precipitation, the resulting solids were structurally characterized by XRD for phase identification and calculation of the unit cell parameter, thermally by TGA for the identification of the mass loss and morphologically by SEM. The sample obtained by precipitation with LiOH at pH 11 / hydrothermal treatment showed diffraction peaks similar to hydrotalcite, morphological and thermal characteristics similar to the pattern Co-Al-Cl LDH obtained by co-precipitation at constant pH 8. (author)

  4. Mercury separation from mixed wastes. Annual report

    International Nuclear Information System (INIS)

    Taylor, P.A.; Klasson, K.T.; Corder, S.L.; Carlson, T.R.; McCandless, K.R.

    1995-11-01

    This is an assessment of new sorbents for removing Hg from wastes at US DOE sites. Four aqueous wastes were used for the laboratory tests: a simulant of a high-salt, acidic waste currently stored at INEL, a simulant of a high-salt, alkaline waste stored at Savannah River (SRS), a dilute LiOH solution stored at Y-12, and a low-salt, neutral groundwater generated at Y-12. Eight adsorbents covering a wide range of cost and capability were tested. Screening tests identified the most promising adsorbents, and column tests were performed using at least two adsorbents for each waste stream. No one adsorbent is effective in all of these waste streams. Based on loading capacity and compatibility, the most effect adsorbents to date are SuperLig 618 for the INEL tank waste simulant, Mersorb and Ionac SR-3 for the SRS tank waste simulant, Durasil 70 and Ionac SR-3 for the LiOH solution, and Ionac SR-3, followed by Ionac SR-4 and Mersorb, for the Y-12 groundwater

  5. Effects of externally supplied lithium on the suppression of ASR expansion in mortars

    International Nuclear Information System (INIS)

    Kawamura, Mitsunori; Kodera, Takeshi

    2005-01-01

    Lithium salts are being externally supplied for mitigating the progress of deterioration of ASR-affected concrete structures. However, it is not clear whether the sodium or potassium in the ASR gel in concrete is replaced by the lithium supplied from the outside. In this article, we examine changes in the composition of the ASR gel, previously formed in mortar specimens, after they are immersed in LiOH solution, using backscattered electron (BSE) imaging and energy-dispersive X-ray (EDX) analysis, associated with length change measurement of the mortar prisms. The intrusion of lithium ions into mortar specimens containing a reactive aggregate could arrest their further expansion within a relatively short time after immersion in 0.50 N LiOH solution. The alkali ions incorporated in most ASR gels, located not far away from interfaces between the cement paste and reactive aggregate particles, appear to be replaced by the lithium ions supplied from the solution. However, the ASR gel within the reacted aggregate particles did not appear to have been affected by the lithium ions

  6. Content provision and multi-homing

    OpenAIRE

    Pires, Armando J. Garcia

    2015-01-01

    We analyze the effects of multi-homing consumers on content provision by media firms. We develop a model where media firms compete on content provision and advertising revenues, and consumers enjoy network effects from consuming content that other consumers also consume. Media firms have to choose if they are single-content or multi-content, and in the latter case how much content to offer. Competition for advertising revenues gives a two-sided market nature to our model, since advertisers pr...

  7. Reducing the cadmium content of crude phosphates and mineral fertilizers

    Energy Technology Data Exchange (ETDEWEB)

    Plessen, H von; Schimmel, G

    1987-10-01

    Crude sedimentary phosphates generally contain cadmium together with traces of other heavy metals. These Cd traces generally end up in fertilizers produced from the crude phosphates. Processes have therefore been developed to separate the Cd from the crude phosphate or from the crude phosphoric acids arising therefrom as intermediates. In this way, the Cd content of the crude phosphate can be reduced to less the 10% of its original value, and to 50% thereof by extractive treatment with acidic calcium nitrate solution. Older calcination processes for crude phosphate have been improved to give residual Cd contents of 10 to 50% at temperatures of 800 to 1000/sup 0/C. Cadmium can be removed almost quantitatively from crude phosphate by means of dialkyl dithiophosphoric acid esters by extraction, binding to adsorbents, or ion flotation. Cadmium can be extracted from crude acids in high yield by long-chained amines. After partial neutralization of the crude acids, precipitation as cadmium sulphide is also possible.

  8. OPTIMIZATION OF PRODUCED WATER TREATMENT PROCESS - A CASE STUDY FOR DISPOSAL IN THE NIGER DELTA

    Directory of Open Access Journals (Sweden)

    BONIFACE A. ORIJI

    2017-12-01

    Full Text Available Produced water is the interstitial reservoir water that flows to the surface with the crude oil into the production separators. This study addressed the effects of some chemicals on produced water and the challenges of finding the optimal concentrations of these chemicals for treating produced water. In this study, produced water treatment was carried out in an oil production platform located in the Niger Delta so as to determine the effect of a particular scale inhibitor, biocide, demulsifier and water clarifier, also to obtain the optimum concentrations of these chemicals in the treatment of produced water. The physico-chemical properties and microbial content of the produced water were determined. The results showed that the conductivity, hardness, pH and alkalinity reduced with increasing concentration of the scale inhibitor. The total heterotrophic bacteria count (THBC, heterotrophic fungi count (THFC and the Sulphate reducing bacteria count (SRBC were found to reduce with increasing concentration of biocide and exposure time. The increase in biocide concentration from 64 PPM to 100 PPM resulted in the reduction of THBC by 99.78%, THFC by 81.32% and SRBC 99.85%. The water clarifier gave the optimum concentration for oil and grease in the produced water at 7.3 PPM.

  9. Integral use of amaranth starch to obtain cyclodextrin glycosyltransferase, by Bacillus megaterium, to produce β-cyclodextrin.

    Directory of Open Access Journals (Sweden)

    María Belem Arce-Vázquez

    2016-09-01

    Full Text Available Cyclodextrin glycosyltransferase (CGTase is an enzyme that produces cyclodextrins (CDs from starch and related carbohydrates, producing a mixture of α-, β-, and γ-CDs in different amounts. CGTase production, mainly by Bacillus sp., depends on fermentation conditions such as pH, temperature, concentration of nutrients, carbon and nitrogen sources, among others. Bacillus megaterium CGTase produces those three types of CDs, however, β-CD should prevail. Although waxy corn starch (CS is used industrially to obtain CGTase and CDs because of its high amylopectin content, alternative sources such as amaranth starch (AS could be used to accomplish those purposes. AS has high susceptibility to the amylolytic activity of CGTase because of its 80% amylopectin content. Therefore, the aim of this work was evaluate the AS as carbon source for CGTase production by B. megaterium in a submerged fermentation. Afterwards, the CGTase was purified partially and its activity to synthesize α-, β- and γ-CDs was evaluated using 1% AS as substrate. B. megaterium produced a 66 kDa CGTase (Topt=50°C; pHopt=8.0, from the early exponential growth phase which lasted 36 h. The maximum CGTase specific activity (106.62±8.33 U/mg protein was obtained after 36 h of culture. CGTase obtained with a Km=0.152 mM and a Vmax=13.4 µM/min yielded 40.47% total CDs using AS which was roughly twice as much as that of corn starch (CS; 24.48%. High costs to produce CDs in the pharmaceutical and food industries might be reduced by using AS because of its higher α-, β- and γ-CDs production (12.81%, 17.94% and 9.92%, respectively in a shorter time than that needed for CS.

  10. Seed yield and protein content in sunflower depending on stand density

    Directory of Open Access Journals (Sweden)

    Balalić Igor M.

    2016-01-01

    Full Text Available The aim of this research was to investigate the effect of stand density on seed yield and protein content in sunflower hybrids. The field experiment was carried out at Rimski Šančevi location. Six NS sunflower hybrids were examined. Five hybrids are confectionery (NS Goliat, NS Slatki, NS Gricko, Vranac and Cepko, and one is used for bird food (NS-H-6485. The trial was arranged as randomized complete block design (RCBD with four replications. Sowing was done with six different densities (from 20,000 to 70,000 plants per hectare, with an increment of 10,000 plants per hectare. Analysis of variance (ANOVA showed that the effect of hybrid, stand density and hybrid × stand density interation were highly significant for seed yield and protein content. The highest seed yield, on the basis of average for all densities, was found in NS-H-6485 (4.77 t ha-1 and in NS Gricko (4.43 t ha-1. Average seed yield of hybrids significantly increased up to 50,000 plants per ha-1, when it reached the value of 4.50 t ha-1, and then decreased. Significantly higher protein content, taking into account all stand densities, showed hybrid Cepko (16.94%. Protein content, above the overall average value, was achieved in hybrid Vranac (16.11%. The high­est protein content in the average for all six hybrids was at the lowest stand density (20,000 plants per ha-1, and then decreased up to higher densities. The results showed that stand density had significant effect on seed yield and protein content in sunflower hybrids. [Projekat Ministarstva nauke Republike Srbije, br. TR31025: The development of new cultivars and improving the technology of producing oil plant species for different purposes

  11. EFFECT OF SOME TECHNOLOGICAL FACTORS ON THE CONTENT OF ACETALDEHYDE IN BEER

    Directory of Open Access Journals (Sweden)

    Gunka Jonkova

    2010-10-01

    Full Text Available The purpose of this work was to examine the influence of the temperature, the pitching rate of yeast and wort composition (Free Amino Nitrogen on the content of acetaldehyde in beer. It is known, that higher fermentation temperatures stimulate the formation of acetaldehyde, as well as the higher rate of acetaldehyde reduction, leading to lower concentrations in the final beer. Beer produced with increased pitching rate of yeast (26 and 35 × 10[sup]6[/sup] cells•mL[sup]-1[/sup], contains lower quantities of acetaldehyde as compared to the control beer. Lower content of α-amino nitrogen in result of substitution of 5 to 10�0of the malt with rice, sugar or a combination of both does not lead to considerable differences in the acetaldehyde concentration in beer.

  12. Partitioning of semi-soluble organic compounds between the water phase and oil droplets in produced water

    Energy Technology Data Exchange (ETDEWEB)

    Faksness, Liv-Guri; Grini, Per Gerhard; Daling, Per S

    2004-04-01

    When selecting produced water treatment technologies, one should focus on reducing the major contributors to the total environmental impact. These are dispersed oil and semi-soluble hydrocarbons, alkylated phenols, and added chemicals. Experiments with produced water have been performed offshore on the Statoil operated platforms Gullfaks C and Statfjord B. These experiments were designed to find how much of the environmentally relevant compounds were dissolved in the water phase and not associated to the dispersed oil in the produced water. Results show that the distribution between the dispersed oil and the water phase varies highly for the different components groups. For example the concentration of PAHs and the C6-C9 alkylated phenols is strongly correlated to the content of dispersed oil. Therefore, the technologies enhancing the removal of dispersed oil have a higher potential for reducing the environmental impact of the produced water than previously considered.

  13. Partitioning of semi-soluble organic compounds between the water phase and oil droplets in produced water

    International Nuclear Information System (INIS)

    Faksness, Liv-Guri; Grini, Per Gerhard; Daling, Per S.

    2004-01-01

    When selecting produced water treatment technologies, one should focus on reducing the major contributors to the total environmental impact. These are dispersed oil and semi-soluble hydrocarbons, alkylated phenols, and added chemicals. Experiments with produced water have been performed offshore on the Statoil operated platforms Gullfaks C and Statfjord B. These experiments were designed to find how much of the environmentally relevant compounds were dissolved in the water phase and not associated to the dispersed oil in the produced water. Results show that the distribution between the dispersed oil and the water phase varies highly for the different components groups. For example the concentration of PAHs and the C6-C9 alkylated phenols is strongly correlated to the content of dispersed oil. Therefore, the technologies enhancing the removal of dispersed oil have a higher potential for reducing the environmental impact of the produced water than previously considered

  14. Yellow sweet potato flour: use in sweet bread processing to increase β-carotene content and improve quality.

    Science.gov (United States)

    Nogueira, Amanda C; Sehn, Georgia A R; Rebellato, Ana Paula; Coutinho, Janclei P; Godoy, Helena T; Chang, Yoon K; Steel, Caroline J; Clerici, Maria Teresa P S

    2018-01-01

    Yellow sweet potato is mostly produced by small farmers, and may be a source of energy and carotenoids in the human diet, but it is a highly perishable crop. To increase its industrial application, yellow sweet potato flour has been produced for use in bakery products. This study aimed to evaluate the technological quality and the carotenoids content in sweet breads produced with the replacement of wheat flour by 0, 3, 6, and 9% yellow sweet potato flour. Breads were characterized by technological parameters and β-carotene levels during nine days of storage. Tukey's test (p<0.05) was used for comparison between means. The increase in yellow sweet potato flour concentrations in bread led to a decrease of specific volume and firmness, and an increase in water activity, moisture, orange coloring, and carotenoids. During storage, the most significant changes were observed after the fifth day, with a decrease in intensity of the orange color. The β-carotene content was 0.1656 to 0.4715 µg/g in breads with yellow sweet potato flour. This work showed a novel use of yellow sweet potato in breads, which brings benefits to consumers' health and for the agricultural business.

  15. Stable, fertile, high polyhydroxyalkanoate producing plants and methods of producing them

    Energy Technology Data Exchange (ETDEWEB)

    Bohmert-Tatarev, Karen; McAvoy, Susan; Peoples, Oliver P.; Snell, Kristi D.

    2015-08-04

    Transgenic plants that produce high levels of polyhydroxybutyrate and methods of producing them are provided. In a preferred embodiment the transgenic plants are produced using plastid transformation technologies and utilize genes which are codon optimized. Stably transformed plants able to produce greater than 10% dwt PHS in tissues are also provided.

  16. Composição centesimal e teor de nitrato em cinco cultivares de alface produzidas sob cultivo hidropônico Centesimal composition and nitrate content in five cultivars of lettuce produced in hydroponic system

    Directory of Open Access Journals (Sweden)

    Silvana Ohse

    2009-01-01

    Full Text Available Com o objetivo de avaliar a qualidade nutricional de cinco cultivares de alface (Mimosa Verde, Mimosa Vermelha, Vera, Regina e Lucy Brown produzidas em cultivo hidropônico sob sistema NFT, determinou-se sua composição centesimal e seu teor de nitrato. O delineamento experimental utilizado foi o inteiramente casualizado com quatro repetições. O experimento foi desenvolvido no Departamento de Engenharia Rural da Universidade Federal de Santa Catarina, Florianópolis (SC, de maio a julho de 2004. As bancadas de produção possuíam sete canais com 6,0 m de comprimento e 1,50 m de largura. O espaçamento utilizado foi 0,25 m e canais e 0,25 m entre plantas no canal. A colheita foi efetuada aos 54 dias após a semeadura, e permanência por 24 dias na bancada de produção. Na cultivar de alface do tipo americana, Lucy Brown, observou-se maior teor de água da parte aérea e também maior teor de nitrato. Nas cultivares Mimosa Vermelha e Mimosa Verde verificaram, em média, maior teor de fitomassa seca da parte aérea, de lipídios, de proteína e maior valor calórico. Na cultivar Mimosa Vermelha constatou-se maior teor de carboidratos e na Mimosa Verde, o maior teor de resíduo mineral, não diferindo da cultivar Regina. O maior teor de fibra foi constatado na cultivar Regina.The nutrition quality of five different lettuce cultivars (Mimosa Verde, Mimosa Vermelha, Vera, Regina and Lucy Brown produced under NFT (Laminar Flow of Solution system was determined by their centesimal composition and nitrate content. To analyze the experimental treatments it was used a completely randomized design with four replications. The experiment was developed in a greenhouse belonging to the Department of Agricultural Engineering of the Federal University of Santa Catarina, Florianópolis, Santa Catarina State, Brazil, from May to July of 2004 (autumn-winter period. The lettuces were grown in a group of benches (3% declivity with seven canals (6.0 m length and 1

  17. Process for producing a novel copolymer. [electron beams

    Energy Technology Data Exchange (ETDEWEB)

    Oiwa, M; Matsumoto, A; Tojima, M; Matsumoto, K; Sasaki, H

    1970-11-27

    Diaryl oxalate present in a polymer not only decomposes at lower temperatures, but also provides for stronger free radicals initiating polymerization than diaryl oxalate present in a monomer. A copolymer of vinyl monomers is produced by providing a diaryl oxalate polymer or a diaryl oxalate monomer-co-vinyl monomer, decomposing them to release the diaryl oxalate units by heating or irradiating with radiation thereby copolymerizing the vinyl monomer with the polymer radicals by utilizing the diaryl oxalate unit. For example, a single diaryl oxalate polymer or a copolymer containing the diaryl oxalate polymer as a constituent of the copolymer are irradiated or heated with a vinyl monomer, i.e. methyl methacrylate, acrylnitrile, vinyl acetate, styrene etc., to form a copolymer without difficulty. In one of the examples, 500 g of diaryl oxalate monomer, 1,200 ml of benzene and 0.2 mol/l of benzoil peroxide as an initiator were mixed and polymerized in nitrogen gas at 70/sup 0/C for 8 hrs. From this polymerized solution, a polymer was deposited in methanol. The produced polymer had an iodin value of 77.7 with a yield of 35%. The gel content of the produced polymer was 98.9% for 10 Mrad. This polymer was dissolved in methyl methacrylate, thereafter filled in a mold and irradiated with electron beams of 2 MeV in nitrogen gas to harden it. The advantage of this process is that the polymerization is effected with low energy radiations at room temperature without requiring any catalyst.

  18. Variation in the fumonisin biosynthetic gene cluster in fumonisin-producing and nonproducing black aspergilli.

    Science.gov (United States)

    Susca, Antonia; Proctor, Robert H; Butchko, Robert A E; Haidukowski, Miriam; Stea, Gaetano; Logrieco, Antonio; Moretti, Antonio

    2014-12-01

    The ability to produce fumonisin mycotoxins varies among members of the black aspergilli. Previously, analyses of selected genes in the fumonisin biosynthetic gene (fum) cluster in black aspergilli from California grapes indicated that fumonisin-nonproducing isolates of Aspergillus welwitschiae lack six fum genes, but nonproducing isolates of Aspergillus niger do not. In the current study, analyses of black aspergilli from grapes from the Mediterranean Basin indicate that the genomic context of the fum cluster is the same in isolates of A. niger and A. welwitschiae regardless of fumonisin-production ability and that full-length clusters occur in producing isolates of both species and nonproducing isolates of A. niger. In contrast, the cluster has undergone an eight-gene deletion in fumonisin-nonproducing isolates of A. welwitschiae. Phylogenetic analyses suggest each species consists of a mixed population of fumonisin-producing and nonproducing individuals, and that existence of both production phenotypes may provide a selective advantage to these species. Differences in gene content of fum cluster homologues and phylogenetic relationships of fum genes suggest that the mutation(s) responsible for the nonproduction phenotype differs, and therefore arose independently, in the two species. Partial fum cluster homologues were also identified in genome sequences of four other black Aspergillus species. Gene content of these partial clusters and phylogenetic relationships of fum sequences indicate that non-random partial deletion of the cluster has occurred multiple times among the species. This in turn suggests that an intact cluster and fumonisin production were once more widespread among black aspergilli. Copyright © 2014 Elsevier Inc. All rights reserved.

  19. Content validity and its estimation

    Directory of Open Access Journals (Sweden)

    Yaghmale F

    2003-04-01

    Full Text Available Background: Measuring content validity of instruments are important. This type of validity can help to ensure construct validity and give confidence to the readers and researchers about instruments. content validity refers to the degree that the instrument covers the content that it is supposed to measure. For content validity two judgments are necessary: the measurable extent of each item for defining the traits and the set of items that represents all aspects of the traits. Purpose: To develop a content valid scale for assessing experience with computer usage. Methods: First a review of 2 volumes of International Journal of Nursing Studies, was conducted with onlyI article out of 13 which documented content validity did so by a 4-point content validity index (CV! and the judgment of 3 experts. Then a scale with 38 items was developed. The experts were asked to rate each item based on relevance, clarity, simplicity and ambiguity on the four-point scale. Content Validity Index (CVI for each item was determined. Result: Of 38 items, those with CVIover 0.75 remained and the rest were discarded reSulting to 25-item scale. Conclusion: Although documenting content validity of an instrument may seem expensive in terms of time and human resources, its importance warrants greater attention when a valid assessment instrument is to be developed. Keywords: Content Validity, Measuring Content Validity

  20. Influence of moisture content, particle size and forming temperature on productivity and quality of rice straw pellets

    Energy Technology Data Exchange (ETDEWEB)

    Ishii, Kazuei, E-mail: k-ishii@eng.hokudai.ac.jp; Furuichi, Toru

    2014-12-15

    Highlights: • Optimized conditions were determined for the production of rice straw pellets. • The moisture content and forming temperature are key factors. • High quality rice pellets in the lower heating value and durability were produced. - Abstract: A large amount of rice straw is generated and left as much in paddy fields, which causes greenhouse gas emissions as methane. Rice straw can be used as bioenergy. Rice straw pellets are a promising technology because pelletization of rice straw is a form of mass and energy densification, which leads to a product that is easy to handle, transport, store and utilize because of the increase in the bulk density. The operational conditions required to produce high quality rice straw pellets have not been determined. This study determined the optimal moisture content range required to produce rice straw pellets with high yield ratio and high heating value, and also determined the influence of particle size and the forming temperature on the yield ratio and durability of rice straw pellets. The optimal moisture content range was between 13% and 20% under a forming temperature of 60 or 80 °C. The optimal particle size was between 10 and 20 mm, considering the time and energy required for shredding, although the particle size did not significantly affect the yield ratio and durability of the pellets. The optimized conditions provided high quality rice straw pellets with nearly 90% yield ratio, ⩾12 MJ/kg for the lower heating value, and >95% durability.