Drivability Improvement Control for Vehicle Start-Up Applied to an Automated Manual Transmission
Danna Jiang
2017-01-01
Full Text Available Drivability is the key factor for the automated manual transmission. It includes fast response to the driver’s demand and the driving comfort. This paper deals with a control methodology applied to an automated manual transmission vehicle for drivability enhancement during vehicle start-up phase. Based on a piecewise model of powertrain, a multiple-model predictive controller (mMPC is designed with the engine speed, clutch disc speed, and wheel speed as the measurable input variables and the engine torque reference and clutch friction torque reference as the controller’s output variables. The model not only includes the clutch dynamic, the flexible shaft dynamic, but also includes the actuators’ delay character. Considering the driver’s intention, a slipping speed trajectory is generated based on the acceleration pedal dynamically. The designed control strategy is verified on a complete powertrain and longitudinal vehicle dynamic model with different driver’s torque demands.
A solution approach for non-linear analysis of concrete members
Hadi, N. M.; Das, S.
1999-01-01
Non-linear solution of reinforced concrete structural members, at and beyond its maximum strength poses complex numerical problems. This is due to the fact that concrete exhibits strain softening behaviour once it reaches its maximum strength. This paper introduces an improved non-linear solution capable to overcome the numerical problems efficiently. The paper also presents a new concept of modeling discrete cracks in concrete members by using gap elements. Gap elements are placed in between two adjacent concrete elements in tensile zone. The magnitude of elongation of gap elements, which represents the width of the crack in concrete, increases edith the increase of tensile stress in those elements. As a result, transfer of local from one concrete element to adjacent elements reduces. Results of non-linear finite element analysis of three concrete beams using this new solution strategy are compared with those obtained by other researchers, and a good agreement is achieved. (authors). 13 refs. 9 figs.,
Mineralization of linear alkylbenzene sulfonate by a four-member aerobic bacterial consortium
Jimenez, L.; Breen, A.; Thomas, N.; Sayler, G.S.; Federle, T.W.
1991-01-01
A bacterial consortium capable of linear alkylbenzene sulfonate (LAS) mineralization under aerobic conditions was isolated from a chemostat inoculated with activated sludge. The consortium, designated KJB, consisted of four members, all of which were gram-negative, rod-shaped bacteria that grew in pairs and short chains. Three isolates had biochemical properties characteristic of Pseudomonas spp.; the fourth showed characteristics of the Aeromonas spp. Cell suspensions were grown together in minimal medium with [ 14 C]LAS as the only carbon source. After 13 days of incubation, more than 25% of the [ 14 C]LAS was mineralized to 14 CO 2 by the consortium. Pure bacterial cultures and combinations lacking any one member of the KJB bacterial consortium did not mineralize LAS. Three isolates carried out primary biodegradation of the surfactant, and one did not. This study shows that the four bacteria complemented each other and synergistically mineralized LAS, indicating catabolic cooperation among the four consortium members
Modeling and control of a hybrid-electric vehicle for drivability and fuel economy improvements
Koprubasi, Kerem
The gradual decline of oil reserves and the increasing demand for energy over the past decades has resulted in automotive manufacturers seeking alternative solutions to reduce the dependency on fossil-based fuels for transportation. A viable technology that enables significant improvements in the overall tank-to-wheel vehicle energy conversion efficiencies is the hybridization of electrical and conventional drive systems. Sophisticated hybrid powertrain configurations require careful coordination of the actuators and the onboard energy sources for optimum use of the energy saving benefits. The term optimality is often associated with fuel economy, although other measures such as drivability and exhaust emissions are also equally important. This dissertation focuses on the design of hybrid-electric vehicle (HEV) control strategies that aim to minimize fuel consumption while maintaining good vehicle drivability. In order to facilitate the design of controllers based on mathematical models of the HEV system, a dynamic model that is capable of predicting longitudinal vehicle responses in the low-to-mid frequency region (up to 10 Hz) is developed for a parallel HEV configuration. The model is validated using experimental data from various driving modes including electric only, engine only and hybrid. The high fidelity of the model makes it possible to accurately identify critical drivability issues such as time lags, shunt, shuffle, torque holes and hesitation. Using the information derived from the vehicle model, an energy management strategy is developed and implemented on a test vehicle. The resulting control strategy has a hybrid structure in the sense that the main mode of operation (the hybrid mode) is occasionally interrupted by event-based rules to enable the use of the engine start-stop function. The changes in the driveline dynamics during this transition further contribute to the hybrid nature of the system. To address the unique characteristics of the HEV
Bayes filter modification for drivability map estimation with observations from stereo vision
Panchenko, Aleksei; Prun, Viktor; Turchenkov, Dmitri
2017-02-01
Reconstruction of a drivability map for a moving vehicle is a well-known research topic in applied robotics. Here creating such a map for an autonomous truck on a generally planar surface containing separate obstacles is considered. The source of measurements for the truck is a calibrated pair of cameras. The stereo system detects and reconstructs several types of objects, such as road borders, other vehicles, pedestrians and general tall objects or highly saturated objects (e.g. road cone). For creating a robust mapping module we use a modification of Bayes filtering, which introduces some novel techniques for occupancy map update step. Specifically, our modified version becomes applicable to the presence of false positive measurement errors, stereo shading and obstacle occlusion. We implemented the technique and achieved real-time 15 FPS computations on an industrial shake proof PC. Our real world experiments show the positive effect of the filtering step.
Wu, Shaohua; Duan, Bin; Qin, Xiaohong; Butcher, Jonathan T
2017-09-15
Polymeric hydrogels have great potential in soft biological micro-actuator applications. However, inappropriate micro-architecture, non-anisotropy, weak biomechanics, and inferior response behaviors limit their development. In this study, we designed and manufactured novel polyacrylonitrile (PAN)-based hydrogel yarns composed with uniaxially aligned nanofibers. The nanofibrous hydrogel yarns possessed anisotropic architecture and robust mechanical properties with flexibility, and could be assembled into defined scaffold structures by subsequent processes. The as-prepared hydrogel yarns showed excellent pH response behaviors, with around 100% maximum length and 900% maximum diameter changes, and the pH response was completed within several seconds. Moreover, the hydrogel yarns displayed unique cell-responsive abilities to promote the cell adhesion, proliferation, and smooth muscle differentiation of human adipose derived mesenchymal stem cells (HADMSC). Chicken cardiomyocytes were further seeded onto our nanofibrous hydrogel yarns to engineer living cell-based microactuators. Our results demonstrated that the uniaxially aligned nanofibrous networks within the hydrogel yarns were the key characteristics leading to the anisotropic organization of cardiac cells, and improved sarcomere organization, mimicking the cardiomyocyte bundles in the native myocardium. The construct is capable of sustaining spontaneous cardiomyocyte pumping behaviors for 7days. Our PAN-based nanofibrous hydrogel yarns are attractive for creating linear microactuators with pH-response capacity and biological microactuators with cardiomyocyte-drivability. A mechanically robust polyacrylonitrile-based nanofibrous hydrogel yarn is fabricated by using a modified electrospinning setup in combination with chemical modification processes. The as-prepared hydrogel yarn possesses a uniaxially aligned nanofiber microarchitecture and supports a rapid, pH-dependent expansion/contraction response within a few
Members of the global linear-collider community who attended IWLC2010 in Geneva
Maximilien Brice
2010-01-01
The International Workshop on Linear Colliders (IWLC2010) recently brought together many experts involved in research and development for an electron–positron linear collider – the favoured future facility to complement the LHC. Organized by the European Committee for Future Accelerators (ECFA) and hosted by CERN, the meeting took place on 18–22 October and attracted 479 registered participants.
Guillaume Colin
2014-09-01
Full Text Available The paper proposes a generic methodology to incorporate constraints (pollutant emission, battery health, drivability into on-line energy management strategies (EMSs for hybrid electric vehicles (HEVs and plug-in hybrid electric vehicles (PHEVs. The integration of each constraint into the EMS, made with the Pontryagin maximum principle, shows a tradeoff between the fuel consumption and the constraint introduced. As state dynamics come into play (catalyst temperature, battery cell temperature, etc., the optimization problem becomes more complex. Simulation results are presented to highlight the contribution of this generic strategy, including constraints compared to the standard approach. These results show that it is possible to find an energy management strategy that takes into account an increasing number of constraints (drivability, pollution, aging, environment, etc.. However, taking these constraints into account increases fuel consumption (the existence of a trade-off curve. This trade-off can be sometimes difficult to find, and the tools developed in this paper should help to find an acceptable solution quickly
Is interstellar detection of higher members of the linear radicals CnCH and CnN feasible?
Pauzat, F.; Ellinger, Y.; Mclean, A. D.
1991-01-01
Rotational constants and dipole moments for linear-chain radicals CnCH and CnN are estimated using a combinatiaon of ab initio molecular orbital calculations and observed data on the starting members of the series. CnCH with n = 0-5 have been observed by radioastronomy in carbon-rich interstellar clouds; higher members of the series have 2Pi ground states with large dipole moments and are strong candidates for observation. CN and C3N have also been observed by radioastronomy; higher members of the series, with the possible exception of C5N, have 2Pi ground states with near-zero dipole moments making their interstellar detection hopeless under present observational conditions. C5N can be a strong candidate only if it has a 2Sigma ground state, and best computations so far indicate that this is not the case.
Is interstellar detection of higher members of the linear radicals CnCH and CnN feasible?
Pauzat, F.; Ellinger, Y.; Mclean, A.D.
1991-01-01
Rotational constants and dipole moments for linear-chain radicals CnCH and CnN are estimated using a combinatiaon of ab initio molecular orbital calculations and observed data on the starting members of the series. CnCH with n = 0-5 have been observed by radioastronomy in carbon-rich interstellar clouds; higher members of the series have 2Pi ground states with large dipole moments and are strong candidates for observation. CN and C3N have also been observed by radioastronomy; higher members of the series, with the possible exception of C5N, have 2Pi ground states with near-zero dipole moments making their interstellar detection hopeless under present observational conditions. C5N can be a strong candidate only if it has a 2Sigma ground state, and best computations so far indicate that this is not the case. 20 refs
Dalian Marius DORAN
2017-11-01
Full Text Available The article aims to research impact of budget balance, whether surplus or deficit, on the main indicator characterizing the economic growth of a country, namely GDP and the inflation rate in the 27 European Union Member States and the United Kingdom. For this analysis was used panel data, taking into account the period from 2001 to 2015. The method used for the analysis is the linear regression with fixed effects and with Driscoll-Kraay standard errors. The dependent variables are the growth rate of real GDP and the inflation rate, and the independent variable is the budget balance (surplus or deficit. The results obtained after using econometric software Stata shows a positive impact of budget balance on growth in the European Union for the analyzed period.
Trujillo, Michael; Perrin, Paul B; Doser, Karoline
2016-01-01
Objective: No studies have examined the impact of personality traits on mental health among caregivers of individuals with severe brain injury. Therefore, the purpose of the current study was to construct linear growth models to examine whether the personality traits of family members...... neuroticism had lower anxiety and depression over time, as well as a more accelerated decrease in anxiety and depression. Conclusions: Caregivers' personality traits were strongly associated over time with mental HRQoL, anxiety, and depression, with neuroticism being especially important for trajectories...... the Short Form-36 assessing mental HRQoL (vitality, social functioning, role limitations-emotional, mental health), anxiety, and depression across 5 time points during the 1st year after injury. The measure of personality was administered 3 months after the patients' discharge. Results: All mental HRQo...
Trujillo, Michael; Perrin, Paul B; Doser, Karoline; Norup, Anne
2016-11-01
No studies have examined the impact of personality traits on mental health among caregivers of individuals with severe brain injury. Therefore, the purpose of the current study was to construct linear growth models to examine whether the personality traits of family members of individuals with severe brain injury could predict the trajectories of their own mental health-related quality of life (HRQoL), anxiety, and depression beginning in a neurointensive care unit through 1 year after injury. Danish family members of individuals with severe brain injury (n = 52) completed the Short Form-36 assessing mental HRQoL (vitality, social functioning, role limitations-emotional, mental health), anxiety, and depression across 5 time points during the 1st year after injury. The measure of personality was administered 3 months after the patients' discharge. All mental HRQoL, anxiety, and depression variables improved significantly over time. Caregivers who were less neurotic and less conscientious had higher vitality, social functioning, and mental health over time, whereas caregivers who were more agreeable had higher social functioning over time. Caregivers with lower neuroticism had lower anxiety and depression over time, as well as a more accelerated decrease in anxiety and depression. Caregivers' personality traits were strongly associated over time with mental HRQoL, anxiety, and depression, with neuroticism being especially important for trajectories of anxiety and depression. These results suggest that personality assessments for caregivers of individuals with severe brain injury could help identify those most at risk for poor mental health over the course of rehabilitation. (PsycINFO Database Record (c) 2016 APA, all rights reserved).
Nassim Kernou
2018-01-01
Full Text Available A rational three-dimensional nonlinear finite element model (NLFEAS is used for evaluating the behavior of high strength concrete slabs under monotonic transverse load. The non-linear equations of equilibrium have been solved using the incremental-iterative technique based on the modified Newton-Raphson method. The convergence of the solution was controlled by a load convergence criterion. The validity of the theoretical formulations and the program used was verified, through comparison with results obtained using ANSYS program and with available experimental test results. A parametric study was conducted to investigate the effect of different parameters on the behavior of slabs which was evaluated in terms of loaddeflection characteristics, concrete and steel stresses and strains, and failure mechanisms. Also, punching shear resistance of slabs was numerically evaluated and compared with the prediction specified by some design codes.
Yang, Xuejin
2016-06-07
Benzo[4,5]cyclohepta[1,2-b]fluorene (5a), a new π-conjugated polycyclic hydrocarbon containing linearly fused six-, five-, six-, seven- and six-membered rings (C6-C5-C6-C7-C6), was designed and its stable derivatives 5b and 5c were synthesized. With 22 π electrons, 5a is an isomer of pentacene with quinoidal, dipolar ionic and diradical resonance forms. Molecules 5b and 5c were experimentally investigated with cyclic voltammetry, electronic absorption spectroscopy and X-ray crystallographic analysis, and theoretically studied by calculating the NICS value, diradical character and dipole moment. A comparison of 5a–c with pentacene and other pentacene analogues containing linearly fused five- or seven- membered rings was also conducted and discussed. It was found that 5b behaved as a p-type organic semiconductor in solution-processed thin film transistors with field effect mobility of up to 0.025 cm2/Vs.
Yang, Xuejin; Shi, Xueliang; Aratani, Naoki; Goncalves, Theo; Huang, Kuo-Wei; Yamada, Hiroko; Chi, Chunyan; Miao, Qian
2016-01-01
Benzo[4,5]cyclohepta[1,2-b]fluorene (5a), a new π-conjugated polycyclic hydrocarbon containing linearly fused six-, five-, six-, seven- and six-membered rings (C6-C5-C6-C7-C6), was designed and its stable derivatives 5b and 5c were synthesized. With 22 π electrons, 5a is an isomer of pentacene with quinoidal, dipolar ionic and diradical resonance forms. Molecules 5b and 5c were experimentally investigated with cyclic voltammetry, electronic absorption spectroscopy and X-ray crystallographic analysis, and theoretically studied by calculating the NICS value, diradical character and dipole moment. A comparison of 5a–c with pentacene and other pentacene analogues containing linearly fused five- or seven- membered rings was also conducted and discussed. It was found that 5b behaved as a p-type organic semiconductor in solution-processed thin film transistors with field effect mobility of up to 0.025 cm2/Vs.
Ebbesen S.
2012-09-01
Full Text Available Automotive manufacturers of hybrid electric vehicles are confronted with the multi-objective non-trivial optimization problem of engine downsizing and electric hybridization under consideration of cost and drivability. Solutions to this sizing problem are typically reached by heuristic design methodologies. However, a design approach formalized in an optimization theoretical setting is necessary in order to obtain globally optimal solutions. In this paper, we present a framework for optimal sizing of hybrid electric drivetrain components. This framework is cast within standard optimization theory. Moreover, it is flexible in order to easily include any number of objectives, such as minimization of fuel consumption, cost of hybridization, emission levels and (or maximization of acceleration performance. Based on this framework, we demonstrate a number of techniques and tools to analyze, accept, improve, or reject the proposed solutions to the optimal sizing problem. Les constructeurs de véhicules automobiles électriques hybrides sont confrontés au problème délicat de l’optimisation multiobjectifs de la réduction de taille moteur et de l’hybridation électrique, tout en considérant le coût et la performance de conduite. Les solutions à ce problème de dimensionnement moteur sont généralement obtenues par des méthodes de conception de type heuristique. Cependant, afin d’obtenir des solutions optimales globales, il est nécessaire de recourir aux formalismes théoriques d’optimisation. Dans cet article, nous présentons une méthodologie de travail, qui s’appuie sur les théories classiques d’optimisation, pour le dimensionnement optimal des composants d’une chaîne de traction électrique hybride. En outre, cette approche est flexible afin de permettre l’ajout d’un nombre quelconque d’objectifs, comme la minimisation de la consommation d’essence, le coût de l’hybridation, les niveaux d’émission et (ou la
Shilov, Georgi E
1977-01-01
Covers determinants, linear spaces, systems of linear equations, linear functions of a vector argument, coordinate transformations, the canonical form of the matrix of a linear operator, bilinear and quadratic forms, Euclidean spaces, unitary spaces, quadratic forms in Euclidean and unitary spaces, finite-dimensional space. Problems with hints and answers.
Thermal effects in concrete members
Kar, A.K.
1977-01-01
The proposed method of analysis for concrete members subjected to temperature changes is consistent with the requirements of ultimate strength design. This also facilitates the provision of the same safety margin as for other loads. Due to cracks and creep in concrete, thermal stresses are nonlinear; they are dependent on the effective member stiffness, which in turn vary with the magnitude of loading. Therefore it is inconsistent to have an ultimate strength design in conjunction with an analysis based on the linear elastic theory. It is proposed that when the requirements of serviceability are met, the neutral axis corresponding to the ultimate load capacity conditions be considered for temperature-induced loadings. This conforms with the fact that the thermal load, because of creep and formation of cracks in the member, can be self-relieving as the failure load condition or ultimate capacity is approached. The maximum thermal load that can develop in dependent on the effective cross section of the member. Recommendations are made for determining the average effective member stiffness, which lies between the stiffness corresponding to the cracked (at ultimate condition) and the uncracked sections. In the proposed method, thermal stresses are not considered completely self-relieving. The stresses are considered simultaneously with stresses resulting from other causes. A step-by-step approach is presented for analysis and design of concrete members subjected to temperature changes
2007-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.63) is Palau which deposited its Instrument of Acceptance of the Statute on 2 March 2007. The Attachment hereto shows the dates on which the present 144 Member States became Members [fr
2007-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.63) is Palau which deposited its Instrument of Acceptance of the Statute on 2 March 2007. The Attachment hereto shows the dates on which the present 144 Member States became Members [es
Suwono.
1978-01-01
A linear gate providing a variable gate duration from 0,40μsec to 4μsec was developed. The electronic circuity consists of a linear circuit and an enable circuit. The input signal can be either unipolar or bipolar. If the input signal is bipolar, the negative portion will be filtered. The operation of the linear gate is controlled by the application of a positive enable pulse. (author)
Vretenar, M
2014-01-01
The main features of radio-frequency linear accelerators are introduced, reviewing the different types of accelerating structures and presenting the main characteristics aspects of linac beam dynamics
Linearization Method and Linear Complexity
Tanaka, Hidema
We focus on the relationship between the linearization method and linear complexity and show that the linearization method is another effective technique for calculating linear complexity. We analyze its effectiveness by comparing with the logic circuit method. We compare the relevant conditions and necessary computational cost with those of the Berlekamp-Massey algorithm and the Games-Chan algorithm. The significant property of a linearization method is that it needs no output sequence from a pseudo-random number generator (PRNG) because it calculates linear complexity using the algebraic expression of its algorithm. When a PRNG has n [bit] stages (registers or internal states), the necessary computational cost is smaller than O(2n). On the other hand, the Berlekamp-Massey algorithm needs O(N2) where N(≅2n) denotes period. Since existing methods calculate using the output sequence, an initial value of PRNG influences a resultant value of linear complexity. Therefore, a linear complexity is generally given as an estimate value. On the other hand, a linearization method calculates from an algorithm of PRNG, it can determine the lower bound of linear complexity.
Said-Houari, Belkacem
2017-01-01
This self-contained, clearly written textbook on linear algebra is easily accessible for students. It begins with the simple linear equation and generalizes several notions from this equation for the system of linear equations and introduces the main ideas using matrices. It then offers a detailed chapter on determinants and introduces the main ideas with detailed proofs. The third chapter introduces the Euclidean spaces using very simple geometric ideas and discusses various major inequalities and identities. These ideas offer a solid basis for understanding general Hilbert spaces in functional analysis. The following two chapters address general vector spaces, including some rigorous proofs to all the main results, and linear transformation: areas that are ignored or are poorly explained in many textbooks. Chapter 6 introduces the idea of matrices using linear transformation, which is easier to understand than the usual theory of matrices approach. The final two chapters are more advanced, introducing t...
Stoll, R R
1968-01-01
Linear Algebra is intended to be used as a text for a one-semester course in linear algebra at the undergraduate level. The treatment of the subject will be both useful to students of mathematics and those interested primarily in applications of the theory. The major prerequisite for mastering the material is the readiness of the student to reason abstractly. Specifically, this calls for an understanding of the fact that axioms are assumptions and that theorems are logical consequences of one or more axioms. Familiarity with calculus and linear differential equations is required for understand
Solow, Daniel
2014-01-01
This text covers the basic theory and computation for a first course in linear programming, including substantial material on mathematical proof techniques and sophisticated computation methods. Includes Appendix on using Excel. 1984 edition.
Liesen, Jörg
2015-01-01
This self-contained textbook takes a matrix-oriented approach to linear algebra and presents a complete theory, including all details and proofs, culminating in the Jordan canonical form and its proof. Throughout the development, the applicability of the results is highlighted. Additionally, the book presents special topics from applied linear algebra including matrix functions, the singular value decomposition, the Kronecker product and linear matrix equations. The matrix-oriented approach to linear algebra leads to a better intuition and a deeper understanding of the abstract concepts, and therefore simplifies their use in real world applications. Some of these applications are presented in detailed examples. In several ‘MATLAB-Minutes’ students can comprehend the concepts and results using computational experiments. Necessary basics for the use of MATLAB are presented in a short introduction. Students can also actively work with the material and practice their mathematical skills in more than 300 exerc...
Berberian, Sterling K
2014-01-01
Introductory treatment covers basic theory of vector spaces and linear maps - dimension, determinants, eigenvalues, and eigenvectors - plus more advanced topics such as the study of canonical forms for matrices. 1992 edition.
Searle, Shayle R
2012-01-01
This 1971 classic on linear models is once again available--as a Wiley Classics Library Edition. It features material that can be understood by any statistician who understands matrix algebra and basic statistical methods.
Christofilos, N.C.; Polk, I.J.
1959-02-17
Improvements in linear particle accelerators are described. A drift tube system for a linear ion accelerator reduces gap capacity between adjacent drift tube ends. This is accomplished by reducing the ratio of the diameter of the drift tube to the diameter of the resonant cavity. Concentration of magnetic field intensity at the longitudinal midpoint of the external sunface of each drift tube is reduced by increasing the external drift tube diameter at the longitudinal center region.
Olive, David J
2017-01-01
This text covers both multiple linear regression and some experimental design models. The text uses the response plot to visualize the model and to detect outliers, does not assume that the error distribution has a known parametric distribution, develops prediction intervals that work when the error distribution is unknown, suggests bootstrap hypothesis tests that may be useful for inference after variable selection, and develops prediction regions and large sample theory for the multivariate linear regression model that has m response variables. A relationship between multivariate prediction regions and confidence regions provides a simple way to bootstrap confidence regions. These confidence regions often provide a practical method for testing hypotheses. There is also a chapter on generalized linear models and generalized additive models. There are many R functions to produce response and residual plots, to simulate prediction intervals and hypothesis tests, to detect outliers, and to choose response trans...
Alcaraz, J.
2001-01-01
After several years of study e''+ e''- linear colliders in the TeV range have emerged as the major and optimal high-energy physics projects for the post-LHC era. These notes summarize the present status form the main accelerator and detector features to their physics potential. The LHC era. These notes summarize the present status, from the main accelerator and detector features to their physics potential. The LHC is expected to provide first discoveries in the new energy domain, whereas an e''+ e''- linear collider in the 500 GeV-1 TeV will be able to complement it to an unprecedented level of precision in any possible areas: Higgs, signals beyond the SM and electroweak measurements. It is evident that the Linear Collider program will constitute a major step in the understanding of the nature of the new physics beyond the Standard Model. (Author) 22 refs
Edwards, Harold M
1995-01-01
In his new undergraduate textbook, Harold M Edwards proposes a radically new and thoroughly algorithmic approach to linear algebra Originally inspired by the constructive philosophy of mathematics championed in the 19th century by Leopold Kronecker, the approach is well suited to students in the computer-dominated late 20th century Each proof is an algorithm described in English that can be translated into the computer language the class is using and put to work solving problems and generating new examples, making the study of linear algebra a truly interactive experience Designed for a one-semester course, this text adopts an algorithmic approach to linear algebra giving the student many examples to work through and copious exercises to test their skills and extend their knowledge of the subject Students at all levels will find much interactive instruction in this text while teachers will find stimulating examples and methods of approach to the subject
Karloff, Howard
1991-01-01
To this reviewer’s knowledge, this is the first book accessible to the upper division undergraduate or beginning graduate student that surveys linear programming from the Simplex Method…via the Ellipsoid algorithm to Karmarkar’s algorithm. Moreover, its point of view is algorithmic and thus it provides both a history and a case history of work in complexity theory. The presentation is admirable; Karloff's style is informal (even humorous at times) without sacrificing anything necessary for understanding. Diagrams (including horizontal brackets that group terms) aid in providing clarity. The end-of-chapter notes are helpful...Recommended highly for acquisition, since it is not only a textbook, but can also be used for independent reading and study. —Choice Reviews The reader will be well served by reading the monograph from cover to cover. The author succeeds in providing a concise, readable, understandable introduction to modern linear programming. —Mathematics of Computing This is a textbook intend...
Reduction of Linear Programming to Linear Approximation
Vaserstein, Leonid N.
2006-01-01
It is well known that every Chebyshev linear approximation problem can be reduced to a linear program. In this paper we show that conversely every linear program can be reduced to a Chebyshev linear approximation problem.
Russell C. Moody; Jen Y. Liu
1999-01-01
Glued structural members are manufactured in a variety of configurations. Structural composite lumber (SCL) products consist of small pieces of wood glued together into sizes common for solid-sawn lumber. Glued-laminated timber (glulam) is an engineered stress-rated product that consists of two or more layers of lumber in which the grain of all layers is oriented...
2017-08-01
Lithuania is on course to become an associate member of CERN, pending final approval by the Lithuanian parliament. Associate membership will allow representatives of the Baltic nation to take part in meetings of the CERN Council, which oversees the Geneva-based physics lab.
Anon.
1992-01-01
The political upheaval in what was the Soviet Union was reflected in an Extraordinary Plenipotentiaries Committee of Joint Institute for Nuclear Research (JINR) Member States, held in Dubna, near Moscow, on 10-13 December, with representatives of eleven sovereign republics of the former Soviet State taking part
Tanwiwat Jaikuna
2017-02-01
Full Text Available Purpose: To develop an in-house software program that is able to calculate and generate the biological dose distribution and biological dose volume histogram by physical dose conversion using the linear-quadratic-linear (LQL model. Material and methods : The Isobio software was developed using MATLAB version 2014b to calculate and generate the biological dose distribution and biological dose volume histograms. The physical dose from each voxel in treatment planning was extracted through Computational Environment for Radiotherapy Research (CERR, and the accuracy was verified by the differentiation between the dose volume histogram from CERR and the treatment planning system. An equivalent dose in 2 Gy fraction (EQD2 was calculated using biological effective dose (BED based on the LQL model. The software calculation and the manual calculation were compared for EQD2 verification with pair t-test statistical analysis using IBM SPSS Statistics version 22 (64-bit. Results: Two and three-dimensional biological dose distribution and biological dose volume histogram were displayed correctly by the Isobio software. Different physical doses were found between CERR and treatment planning system (TPS in Oncentra, with 3.33% in high-risk clinical target volume (HR-CTV determined by D90%, 0.56% in the bladder, 1.74% in the rectum when determined by D2cc, and less than 1% in Pinnacle. The difference in the EQD2 between the software calculation and the manual calculation was not significantly different with 0.00% at p-values 0.820, 0.095, and 0.593 for external beam radiation therapy (EBRT and 0.240, 0.320, and 0.849 for brachytherapy (BT in HR-CTV, bladder, and rectum, respectively. Conclusions : The Isobio software is a feasible tool to generate the biological dose distribution and biological dose volume histogram for treatment plan evaluation in both EBRT and BT.
Supporting Members and Friends
2005-10-01
Thank you! Over the past year, AGU has received 12,104 gifts, both large and small, from members and friends. The Union has also received corporate contributions, National Science Foundation grants, and support from the National Oceanographic Partnership Program and National Association of Geoscience Teachers. Together their generosity has benefited AGU non revenue producing programs that are critical to our science and the future health of the Union. The following list gratefully acknowledges annual gifts of $100 or more and cumulative giving of $5,000 or more. The 1919 Society ($100,000 or more) and Benefactors ($5,000-$99,999) recognize single major gifts and cumulative contributions. Three circles acknowledge annual giving: President's Circle ($1,000 or more), Leadership Circle ($200-$999), and Supporters Circle ($100-$199). Supporting Life Members, who contribute a one-time gift of $1,200 in addition to lifetime dues, are among our most loyal Supporters.
Staff Association
2018-01-01
Summer is coming, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 25 € instead of 31 €. Access to Aqualibi: 5 € instead of 8 € on presentation of your Staff Association member ticket. Free for children under 100 cm. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.
Staff Association
2017-01-01
Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 24 € instead of 30 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children under 100 cm. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.
Staff Association
2017-01-01
Summer is coming, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 24 € instead of 30 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children under 100 cm. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.
Richman, Barbara T.
The new Board on Ocean Science and Policy (BOSP) (Eos, June 7, 1983, p. 402) met for the first time on May 4. John B. Slaughter, former director of the National Science Foundation and now chancellor of the University of Maryland in College Park, is the board's chairman. Other board members are D. James Baker, Jr. (University of Washington, Seattle); Kirk Bryan (Geophysical Fluid Dynamics Laboratory, Princeton University); John P. Craven (University of Hawaii); Charles L. Drake (Dartmouth College); Paul M. Fye (Woods Hole Oceanographic Institution); Edward D. Goldberg (Scripps Institution of Oceanography); G. Ross Heath (Oregon State University); Judith T. Kildow (Massachusetts Institute of Technology); John A. Knauss (University of Rhode Island); James J. McCarthy (Museum of Comparative Zoology, Harvard University); H. William Menard (Scripps Institution of Oceanography); C. Barry Raleigh (Lamont-Doherty Geological Observatory); Roger Revelle (University of California, San Diego); David A. Ross (Woods Hole Oceanographic Institution); Brian J. Rothschild (University of Maryland); William M. Sackett (University of South Florida); John H. Steele (Woods Hole Oceanographic Institution); and Carl Wunsch (MIT). Wallace Broecker (Lamont-Doherty Geological Observatory), an original board member, resigned after the first meeting. Broecker told Eos that combining the science and policy boards resulted in a new board whose mission is too broad. A new board member will be appointed in Broecker's place
Perceived Family Resources Based on Number of Members with ADHD
Corwin, Melinda; Mulsow, Miriam; Feng, Du
2012-01-01
Objective: This study examines how the number of family members with ADHD affects other family members' perceived resources. Method: A total of 40 adolescents diagnosed with ADHD and their mothers, fathers, and adolescent siblings living in the household participated. Hierarchical linear modeling was used to analyze family-level data from a total…
Characteristic polynomials of linear polyacenes and their ...
Coefficients of characteristic polynomials (CP) of linear polyacenes (LP) have been shown to be obtainable from Pascal's triangle by using a graph factorisation and squaring technique. Strong subspectrality existing among the members of the linear polyacene series has been shown from the derivation of the CP's. Thus it ...
2007-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.63) is Palau which deposited its Instrument of Acceptance of the Statute on 2 March 2007. The Attachment hereto shows the dates on which the present 144 Member States became Members
2009-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.67) is Cambodia which deposited its Instrument of Acceptance of the Statute on 23 November 2009. The Attachment hereto shows the dates on which the present 151 Member States became Members
2008-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.64) is Nepal which deposited its Instrument of Acceptance of the Statute on 8 July 2008. The Attachment hereto shows the dates on which the present 145 Member States became Members
2006-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.61) are Belize, Mozambique and Malawi, which deposited their Instruments of Acceptance of the Statute on 31 March 2006, 18 September 2006 and 2 October 2006 respectively. The Attachment hereto shows the dates on which the present 142 Member States became Members
2009-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.66) are Bahrain, Burundi, Congo and Lesotho which deposited their Instruments of Acceptance of the Statute on 23 June 2009, 24 June 2009, 15 July 2009 and 13 July 2009, respectively. The Attachment hereto shows the dates on which the present 150 Member States became Members
2006-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.62) is Montenegro which deposited its Instrument of Acceptance of the Statute on 30 October 2006. The Attachment hereto shows the dates on which the present 143 Member States became Members
2009-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.66) are Bahrain, Burundi, Congo and Lesotho which deposited their Instruments of Acceptance of the Statute on 23 June 2009, 24 June 2009, 15 July 2009 and 13 July 2009, respectively. The Attachment hereto shows the dates on which the present 150 Member States became Members [ru
2009-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.67) is Cambodia which deposited its Instrument of Acceptance of the Statute on 23 November 2009. The Attachment hereto shows the dates on which the present 151 Member States became Members [fr
2006-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.61) are Belize, Mozambique and Malawi, which deposited their Instruments of Acceptance of the Statute on 31 March 2006, 18 September 2006 and 2 October 2006 respectively. The Attachment hereto shows the dates on which the present 142 Member States became Members [fr
2009-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.66) are Bahrain, Burundi, Congo and Lesotho which deposited their Instruments of Acceptance of the Statute on 23 June 2009, 24 June 2009, 15 July 2009 and 13 July 2009, respectively. The Attachment hereto shows the dates on which the present 150 Member States became Members [fr
2009-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.65) is the Sultanate of Oman which deposited its Instrument of Acceptance of the Statute on 5 February 2009. The Attachment hereto shows the dates on which the present 146 Member States became Members [fr
2005-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.59) is the Islamic Republic of Mauritania, which deposited the instrument of acceptance of the Statute on 23 November 2004. The Attachment hereto shows the dates on which the present 138 Member States became Members
2009-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.66) are Bahrain, Burundi, Congo and Lesotho which deposited their Instruments of Acceptance of the Statute on 23 June 2009, 24 June 2009, 15 July 2009 and 13 July 2009, respectively. The Attachment hereto shows the dates on which the present 150 Member States became Members [es
2009-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.67) is Cambodia which deposited its Instrument of Acceptance of the Statute on 23 November 2009. The Attachment hereto shows the dates on which the present 151 Member States became Members [es
2006-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.60) is Chad, which deposited the instrument of acceptance of the Statute on 2 November 2005. The Attachment hereto shows the dates on which the present 139 Member States became Members
2009-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.65) is the Sultanate of Oman which deposited its Instrument of Acceptance of the Statute on 5 February 2009. The Attachment hereto shows the dates on which the present 146 Member States became Members [es
2003-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.58) is Kyrgyzstan, which deposited the instrument of acceptance of the Statute on 10 September 2003. The list shows the dates on which the present 137 Member States became Members
2009-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.65) is the Sultanate of Oman which deposited its Instrument of Acceptance of the Statute on 5 February 2009. The Attachment hereto shows the dates on which the present 146 Member States became Members
2009-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.67) is Cambodia which deposited its Instrument of Acceptance of the Statute on 23 November 2009. The Attachment hereto shows the dates on which the present 151 Member States became Members [ru
Staff Association
2013-01-01
Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 21 € instead of 26 €. Access to Aqualibi: 5 € instead of 8 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12 h 00. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 30 CHF instead of 39 CHF – Adults : 36 CHF instead of 49 CHF Bonus! Free for children under 5.
Staff Association
2015-01-01
Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 21,50 € instead of 27 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12:00 p.m. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.
Staff Association
2016-01-01
Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 23 € instead of 29 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12:00 p.m. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.
Niemann, R.C.; Gonczy, J.D.; Nicol, T.H.
1987-01-01
A cryogenic support member is described for restraining a cryogenic system comprising; a rod having a depression at a first end. The rod is made of non-metallic material. The non-metallic material has an effectively low thermal conductivity; a metallic plug; and a metallic sleeve. The plug and the sleeve are shrink-fitted to the depression in the rod and assembled thereto such that the plug is disposed inside the depression of the rod. The sleeve is disposed over the depression in the rod and the rod is clamped therebetween. The shrink-fit clamping the rod is generated between the metallic plug and the metallic sleeve
Thermal effects in concrete members
Kar, A.K.
1977-01-01
When subjected to temperature changes and restrained from free movement, a member develops stresses. Restrained members are sometimes assumed to act independently of other members. A method of analysis and design for thermal stresses in such members is provided. The method of analysis, based on the ultimate strength concept, greatly reduces the computational efforts for determining thermal effects in concrete members. Available charts and tables and the recommendations given herein simplify the design. (Auth.)
Linear Algebra and Smarandache Linear Algebra
Vasantha, Kandasamy
2003-01-01
The present book, on Smarandache linear algebra, not only studies the Smarandache analogues of linear algebra and its applications, it also aims to bridge the need for new research topics pertaining to linear algebra, purely in the algebraic sense. We have introduced Smarandache semilinear algebra, Smarandache bilinear algebra and Smarandache anti-linear algebra and their fuzzy equivalents. Moreover, in this book, we have brought out the study of linear algebra and vector spaces over finite p...
Staff Association
2013-01-01
The Courir shops propose the following offer: 15% discount on all articles (not on sales) in the Courir shops (Val Thoiry, Annemasse and Neydens) and 5% discount on sales upon presentation of your Staff Association membership card and an identity card before payment. Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 21 € instead of 26 €. Access to Aqualibi: 5 € instead of 8 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12 h 00. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 30 CHF instead of 39 CHF – Adults : 36 CHF instead of 49 CHF Bonus! Free for children under 5.
Association du personnel
2013-01-01
La banque LCL propose aux membres de l’Association du personnel les avantages suivants : – Un barème Privilège sur le Prêt immobilier – Des avantages tarifaires sur l’épargne, notamment l’assurance-vie. – Un taux préférentiel de prêt à la consommation. En outre, jusqu’au 30 septembre 2013, elle offre 50€ à tous les nouveaux clients, membres de l'Association du personnel. Summer is here, enjoy our offers for the aquatic parcs! Tickets "Zone terrestre" : 21 € instead of de 26 €. Access to Aqualibi : 5 euros instead of 8 euros on presentation of your SA member ticket. Free for children (3-11 years old) before 12 h 00. Free for children under 3, with limited access to the attractions. Free car park. * * * * * * * Full day ticket: – Children : 30 CHF instead of 39 CHF &...
Staff Association
2013-01-01
The warm weather arrives, it's time to take advantage of our offers Walibi and Aquapark! Walibi : Tickets "Zone terrestre": 21 € instead of 26 € Access to Aqualibi: 5 € instead of 8 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12 h 00. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Half-day ticket (5 hours): – Children: 26 CHF instead of 35 CHF – Adults : 32 CHF instead of 43 CHF Day ticket: – Children: 30 CHF instead of 39 CHF – Adults : 36 CHF instead of 49 CHF Free for children under 5.
2003-01-01
The document lists the 135 Member States of the Agency as of 19 March 2003. The new Member since the last issue of the list (INFCIRC/2/56) is the Republic of Honduras. The dates on which the present 135 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute
1999-01-01
The document lists the 130 Member States of the Agency as of 1 December 1999. The new Member since the last issue of the list (INFCIRC/2/52) is Angola. The dates on which the present 130 Member States became Members, and the state Honduras) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute are given in an Attachment
2002-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.55) is the Republic of Botswana, which deposited the instrument of acceptance of the Statute on 20 March 2002. The Attachment hereto shows the dates on which the present 134 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute
2001-01-01
The document lists the 132 Member States of the Agency as of 1 June 2001. The new Members since the last issue of the list (INFCIRC/2/53) are Central African Republic and Azerbaijan. The dates on which the present 132 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.69) is the Commonwealth of Dominica, which deposited its instrument of acceptance of the Statute on 17 February 2012. The Attachment hereto shows the dates on which the present 153 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.70) is Papua New Guinea, which deposited its instrument of acceptance of the Statute on 4 April 2012. The Attachment hereto shows the dates on which the present 154 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.69) is the Commonwealth of Dominica, which deposited its instrument of acceptance of the Statute on 17 February 2012. The Attachment hereto shows the dates on which the present 153 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es
2013-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.74) is Swaziland, which deposited its instrument of acceptance of the Statute on 15 February 2013. The Attachment hereto shows the dates on which the present 159 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.71) is Rwanda, which deposited its instrument of acceptance of the Statute on 4 September 2012. The Attachment hereto shows the dates on which the present 155 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
2011-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.68) is the Lao People's Democratic Republic which deposited its instrument of acceptance of the Statute on 4 November 2011. The Attachment hereto shows the dates on which the present 152 Member States deposited instruments of ratification or acceptance of the Statue with the depositary Government [fr
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.73) is Trinidad and Tobago, which deposited its instrument of acceptance of the Statute on 9 November 2012. The Attachment hereto shows the dates on which the present 158 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.70) is Papua New Guinea, which deposited its instrument of acceptance of the Statute on 4 April 2012. The Attachment hereto shows the dates on which the present 154 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [ru
Family members' experiences of autopsy
Oppewal, F; Meyboom-de Jong, B
Background. The experiences of family members will teach us how to handle an autopsy, the ultimate quality assessment tool. Objective. The aim of this study was to determine surviving family members' experience of autopsy. Method. Seven GPs were asked to approach surviving family members of
2014-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.76) is Brunei Darussalam, which deposited its instrument of acceptance of the Statute on 18 February 2014. The Attachment hereto shows the dates on which the present 162 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.70) is Papua New Guinea, which deposited its instrument of acceptance of the Statute on 4 April 2012. The Attachment hereto shows the dates on which the present 154 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.71) is Rwanda, which deposited its instrument of acceptance of the Statute on 4 September 2012. The Attachment hereto shows the dates on which the present 155 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.69) is the Commonwealth of Dominica, which deposited its instrument of acceptance of the Statute on 17 February 2012. The Attachment hereto shows the dates on which the present 153 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr
1993-01-01
The 42nd revision of INFCIRC/2 lists the 113 Member States of the International Atomic Energy Agency as of 1 January 1993. It includes Slovenia as a new Member State as of 21 September 1992, Cambodia replaces the former name ''Democratic Kampuchea'' and Czechoslovakia was deleted as it ceased to be a member of the Agency as of 1 January 1993 (INFCIRC/417)
2011-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.68) is the Lao People's Democratic Republic which deposited its instrument of acceptance of the Statute on 4 November 2011. The Attachment hereto shows the dates on which the present 152 Member States deposited instruments of ratification or acceptance of the Statue with the depositary Government [es
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.73) is Trinidad and Tobago, which deposited its instrument of acceptance of the Statute on 9 November 2012. The Attachment hereto shows the dates on which the present 158 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.70) is Papua New Guinea, which deposited its instrument of acceptance of the Statute on 4 April 2012. The Attachment hereto shows the dates on which the present 154 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.71) is Rwanda, which deposited its instrument of acceptance of the Statute on 4 September 2012. The Attachment hereto shows the dates on which the present 155 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es
2014-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.76) is Brunei Darussalam, which deposited its instrument of acceptance of the Statute on 18 February 2014. The Attachment hereto shows the dates on which the present 162 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es
2012-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.72) are Fiji and Togo, which deposited their instruments of acceptance of the Statute on 2 November 2012 and 1 November 2012, respectively. The Attachment hereto shows the dates on which the present 157 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
2014-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.76) is Brunei Darussalam, which deposited its instrument of acceptance of the Statute on 18 February 2014. The Attachment hereto shows the dates on which the present 162 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.73) is Trinidad and Tobago, which deposited its instrument of acceptance of the Statute on 9 November 2012. The Attachment hereto shows the dates on which the present 158 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
2011-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.68) is the Lao People's Democratic Republic which deposited its instrument of acceptance of the Statute on 4 November 2011. The Attachment hereto shows the dates on which the present 152 Member States deposited instruments of ratification or acceptance of the Statue with the depositary Government
2012-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.71) is Rwanda, which deposited its instrument of acceptance of the Statute on 4 September 2012. The Attachment hereto shows the dates on which the present 155 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [ru
Linearly constrained minimax optimization
Madsen, Kaj; Schjær-Jacobsen, Hans
1978-01-01
We present an algorithm for nonlinear minimax optimization subject to linear equality and inequality constraints which requires first order partial derivatives. The algorithm is based on successive linear approximations to the functions defining the problem. The resulting linear subproblems...
Linear accelerator with x-ray absorbing insulators
Rose, P.H.
1975-01-01
Annular insulators for supporting successive annular electrodes in a linear accelerator have embedded x-ray absorbing shield structures extending around the accelerating path. The shield members are disposed to intercept x-ray radiation without disrupting the insulative effect of the insulator members. In preferred forms, the structure comprises a plurality of annular members of heavy metal disposed in an x-ray blocking array, spaced from each other by the insulating substance of the insulator member. (auth)
Design of reinforced concrete members based on structural mechanics
Diaz, B.E.; Schulz, M.
1984-01-01
Up to now the design of reinforced concrete linear members is performed with the help of an inconsistent design theory, which nevertherless is sufficiently safe and simple to be used in the practice. The purpose of this paper is to present a rational reinforced concrete design method which is not too dissimilar to the present design rules, but is capable of defining consistently internal stresses along a reinforced concrete section. The present status of the completed computer procedures allows the analysis of linear reinforced concrete members formed by laminar reinforced concrete plates presenting variable thickness. A practical approach is presented for which the concrete and steel section is constant along the member axis. In this case, the concept of the equivalent section is introduced, which allows a simple analysis of the stress pattern along the member section. (Author) [pt
2012-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.72) are Fiji and Togo, which deposited their instruments of acceptance of the Statute on 2 November 2012 and 1 November 2012, respectively. The Attachment hereto shows the dates on which the present 157 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [ru
2012-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.72) are Fiji and Togo, which deposited their instruments of acceptance of the Statute on 2 November 2012 and 1 November 2012, respectively. The Attachment hereto shows the dates on which the present 157 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr
1999-01-01
The document lists the 129 Member States of the Agency as of 1 June 1999. The new Member since the last issue of the list (INFCIRC/2/51) is Benin. The dates on which the present 129 states became Members, and the state (Honduras) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 43rd session of the General Conference are given in an Attachment
2012-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.72) are Fiji and Togo, which deposited their instruments of acceptance of the Statute on 2 November 2012 and 1 November 2012, respectively. The Attachment hereto shows the dates on which the present 157 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es
1995-01-01
The new member since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.44) is Yemen. The Attachment hereto shows the dates on which the 122 States became members of the Agency, as well as the State whose application for membership of the Agency was approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute
2014-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.75) are San Marino and the Bahamas, which deposited their instruments of acceptance of the Statute on 25 November 2013 and 7 January 2014, respectively. The Attachment hereto shows the dates on which the present 161 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es
1994-01-01
The new members since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.42) are: Armenia, Coratia, the Czech Republic, Lithuania, the Marshall Islands, the Slovak Republic and Uzbekistan. The Attachment to the circular shows the dates on which the 120 States became members of the Agency, as well as those States whose application for membership of the Agency was approved by the General Conference, but who have not yet deposited an instrument of acceptance of the Statute
1998-01-01
The document lists the 128 Member States of the Agency as of 18 September 1998. The new Member since the last issue of the list (INFCIRC/2/50) is Burkina Faso. In an attachment the dates on which the present 128 states became Members, and the state (Benin) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 42nd session of the General Conference are given
2014-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.75) are San Marino and the Bahamas, which deposited their instruments of acceptance of the Statute on 25 November 2013 and 7 January 2014, respectively. The Attachment hereto shows the dates on which the present 161 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
NONE
1995-02-13
The new member since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.44) is Yemen. The Attachment hereto shows the dates on which the 122 States became members of the Agency, as well as the State whose application for membership of the Agency was approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute.
1998-01-01
The document lists the 127 Member States of the Agency as of 1 January 1998. The new Members since the last issue of of the list (INFCIRC/2/49) are Malta and the Republic of Moldova. In an attachment are given the dates on which the present 127 states become Members, the state (Burkina Faso) whose application for membership of the Agency has been approved by the General Conference but which has not deposited an instrument of acceptance of the Statute
NONE
1998-01-15
The document lists the 127 Member States of the Agency as of 1 January 1998. The new Members since the last issue of of the list (INFCIRC/2/49) are Malta and the Republic of Moldova. In an attachment are given the dates on which the present 127 states become Members, the state (Burkina Faso) whose application for membership of the Agency has been approved by the General Conference but which has not deposited an instrument of acceptance of the Statute.
NONE
1998-09-18
The document lists the 128 Member States of the Agency as of 18 September 1998. The new Member since the last issue of the list (INFCIRC/2/50) is Burkina Faso. In an attachment the dates on which the present 128 states became Members, and the state (Benin) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 42nd session of the General Conference are given
NONE
1999-06-16
The document lists the 129 Member States of the Agency as of 1 June 1999. The new Member since the last issue of the list (INFCIRC/2/51) is Benin. The dates on which the present 129 states became Members, and the state (Honduras) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 43rd session of the General Conference are given in an Attachment.
2014-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.75) are San Marino and the Bahamas, which deposited their instruments of acceptance of the Statute on 25 November 2013 and 7 January 2014, respectively. The Attachment hereto shows the dates on which the present 161 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr
Foundations of linear and generalized linear models
Agresti, Alan
2015-01-01
A valuable overview of the most important ideas and results in statistical analysis Written by a highly-experienced author, Foundations of Linear and Generalized Linear Models is a clear and comprehensive guide to the key concepts and results of linear statistical models. The book presents a broad, in-depth overview of the most commonly used statistical models by discussing the theory underlying the models, R software applications, and examples with crafted models to elucidate key ideas and promote practical model building. The book begins by illustrating the fundamentals of linear models,
2001-01-01
The new Members since the last list of Member States was issued (INFCIRC/2/Rev.54) are the Republic of Tajikistan, which deposited the instrument of acceptance of the Statute on 10 September 2001 and the Federal Republic of Yugoslavia, which deposited the instrument of acceptance of the Statute on 31 October 2001. The Attachment hereto shows the dates on which the present 133 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference, but which have not yet deposited an instrument of acceptance of the Statute
1996-01-01
The document lists the 124 Member States of the Agency as of 1 September 1996. The new Member since the last issue of the list (INFCIRC/2/Rev.47) is Georgia. In an attachment are given the dates on which the 124 Member States became Members, the State (Latvia) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the State (Republic of Moldova) whose application for membership has been recommended by the Board of Governors for approval by the General Conference
1996-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.46) is Bosnia and Herzegovina. The Attachment hereto shows the dates on which the present 123 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference but which have not yet deposited an instrument of acceptance of the Statute and the State whose application for membership has been recommended by the Board of Governors for approval by the General Conference
1995-01-01
No new Member has joined the Agency since the last list of Member States was issued (INFCIRC/2/Rev.45). The Attachment hereto shows the dates on which the present 122 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States whose applications for membership have been recommended by the Board of Governors for approval by the General Conference
2003-01-01
The document lists the 136 Member States of the Agency as of 6 May 2003. The new Members since the last issue of the list (INFCIRC/2/57) are Eritrea and the Republic of Seychelles. Cambodia withdrew from the Agency with effect from 26 March 2003. The dates on which the present 136 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute
NONE
1996-09-10
The document lists the 124 Member States of the Agency as of 1 September 1996. The new Member since the last issue of the list (INFCIRC/2/Rev.47) is Georgia. In an attachment are given the dates on which the 124 Member States became Members, the State (Latvia) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the State (Republic of Moldova) whose application for membership has been recommended by the Board of Governors for approval by the General Conference.
NONE
1995-09-11
No new Member has joined the Agency since the last list of Member States was issued (INFCIRC/2/Rev.45). The Attachment hereto shows the dates on which the present 122 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States whose applications for membership have been recommended by the Board of Governors for approval by the General Conference.
NONE
1996-02-26
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.46) is Bosnia and Herzegovina. The Attachment hereto shows the dates on which the present 123 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference but which have not yet deposited an instrument of acceptance of the Statute and the State whose application for membership has been recommended by the Board of Governors for approval by the General Conference.
Linear positivity and virtual probability
Hartle, James B.
2004-01-01
We investigate the quantum theory of closed systems based on the linear positivity decoherence condition of Goldstein and Page. The objective of any quantum theory of a closed system, most generally the universe, is the prediction of probabilities for the individual members of sets of alternative coarse-grained histories of the system. Quantum interference between members of a set of alternative histories is an obstacle to assigning probabilities that are consistent with the rules of probability theory. A quantum theory of closed systems therefore requires two elements: (1) a condition specifying which sets of histories may be assigned probabilities and (2) a rule for those probabilities. The linear positivity condition of Goldstein and Page is the weakest of the general conditions proposed so far. Its general properties relating to exact probability sum rules, time neutrality, and conservation laws are explored. Its inconsistency with the usual notion of independent subsystems in quantum mechanics is reviewed. Its relation to the stronger condition of medium decoherence necessary for classicality is discussed. The linear positivity of histories in a number of simple model systems is investigated with the aim of exhibiting linearly positive sets of histories that are not decoherent. The utility of extending the notion of probability to include values outside the range of 0-1 is described. Alternatives with such virtual probabilities cannot be measured or recorded, but can be used in the intermediate steps of calculations of real probabilities. Extended probabilities give a simple and general way of formulating quantum theory. The various decoherence conditions are compared in terms of their utility for characterizing classicality and the role they might play in further generalizations of quantum mechanics
Materials Delivered by Member States
1969-01-01
In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 30 June 1969 in compliance with requests the Agency had made under Article IX. D
Materials Delivered by Member States
1975-01-01
In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to 30 June 1975, in compliance with requests the Agency had made under Article IX. D
Materials Delivered by Member States
1974-01-01
In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to 31 March 1974, in compliance with requests the Agency had made under Article IX. D
Materials Delivered by Member States
1971-01-01
In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1970, in compliance with requests the Agency had made under Article IX. D
Materials Delivered by Member States
1973-01-01
In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1972, in compliance with requests the Agency had made under Article IX. D
Materials Delivered by Member States
1972-01-01
In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1971, in compliance with requests the Agency had made under Article IX. D
Working with Difficult Group Members.
Kottler, Jeffrey A.
1994-01-01
Describes types of group members who are challenging in group settings including entitled, manipulative, and character-disordered clients. Provides suggestions for working with these group members, either as isolated cases or as homogenous populations, emphasizing the protection of other clients' rights. Includes 31 references. (Author/CRR)
1997-01-01
The document lists the 125 Member States of the Agency as of 1 September 1997. The new Member since the last issue of the list (INFCIRC/2/Rev.48) is Latvia. In an Attachment are given the dates on which the present 125 States became Members, the State (Republic of Moldova) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States (Malta and Burkina Faso) whose applications for membership have been recommended by the Board of Governors for approval by the General Conference
1994-01-01
The new members since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.43) are: Kazakhstan and the former Yugoslav Republic of Macedonia. The Democratic People's Republic of Korea withdrew from membership of the Agency as of 13 June 1994. The Attachment hereto shows the dates on which the 121 States became members of the Agency, as well as those States whose application for membership of the Agency was approved by the General Conference, but who have not yet deposited an instrument of acceptance of the Statute
NONE
1997-09-22
The document lists the 125 Member States of the Agency as of 1 September 1997. The new Member since the last issue of the list (INFCIRC/2/Rev.48) is Latvia. In an Attachment are given the dates on which the present 125 States became Members, the State (Republic of Moldova) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States (Malta and Burkina Faso) whose applications for membership have been recommended by the Board of Governors for approval by the General Conference.
Multivariate generalized linear mixed models using R
Berridge, Damon Mark
2011-01-01
Multivariate Generalized Linear Mixed Models Using R presents robust and methodologically sound models for analyzing large and complex data sets, enabling readers to answer increasingly complex research questions. The book applies the principles of modeling to longitudinal data from panel and related studies via the Sabre software package in R. A Unified Framework for a Broad Class of Models The authors first discuss members of the family of generalized linear models, gradually adding complexity to the modeling framework by incorporating random effects. After reviewing the generalized linear model notation, they illustrate a range of random effects models, including three-level, multivariate, endpoint, event history, and state dependence models. They estimate the multivariate generalized linear mixed models (MGLMMs) using either standard or adaptive Gaussian quadrature. The authors also compare two-level fixed and random effects linear models. The appendices contain additional information on quadrature, model...
Leader-Member Exchange, Learning Orientation and Innovative Work Behavior
Atitumpong, Aungkhana; Badir, Yuosre F.
2018-01-01
Purpose: This study aims to examine the effects of leader-member exchange (LMX) and employee learning orientation on employee innovative work behavior (IWB) through creative self-efficacy. Design/methodology/approach: Data have been collected from 337 employees and 137 direct managers from manufacturing sector. A hierarchical linear model has been…
Tuey, R. C.
1972-01-01
Computer solutions of linear programming problems are outlined. Information covers vector spaces, convex sets, and matrix algebra elements for solving simultaneous linear equations. Dual problems, reduced cost analysis, ranges, and error analysis are illustrated.
Peterson, David; Stofleth, Jerome H.; Saul, Venner W.
2017-07-11
Linear shaped charges are described herein. In a general embodiment, the linear shaped charge has an explosive with an elongated arrowhead-shaped profile. The linear shaped charge also has and an elongated v-shaped liner that is inset into a recess of the explosive. Another linear shaped charge includes an explosive that is shaped as a star-shaped prism. Liners are inset into crevices of the explosive, where the explosive acts as a tamper.
Classifying Linear Canonical Relations
Lorand, Jonathan
2015-01-01
In this Master's thesis, we consider the problem of classifying, up to conjugation by linear symplectomorphisms, linear canonical relations (lagrangian correspondences) from a finite-dimensional symplectic vector space to itself. We give an elementary introduction to the theory of linear canonical relations and present partial results toward the classification problem. This exposition should be accessible to undergraduate students with a basic familiarity with linear algebra.
Lawson, C. L.; Krogh, F. T.; Gold, S. S.; Kincaid, D. R.; Sullivan, J.; Williams, E.; Hanson, R. J.; Haskell, K.; Dongarra, J.; Moler, C. B.
1982-01-01
The Basic Linear Algebra Subprograms (BLAS) library is a collection of 38 FORTRAN-callable routines for performing basic operations of numerical linear algebra. BLAS library is portable and efficient source of basic operations for designers of programs involving linear algebriac computations. BLAS library is supplied in portable FORTRAN and Assembler code versions for IBM 370, UNIVAC 1100 and CDC 6000 series computers.
Burnout in Female Faculty Members.
Cassidy-Vu, Lisa; Beck, Keli; Moore, Justin B
2017-04-01
Despite approximately equal numbers of male and female medical school graduates, women are entering academic medicine at a lower rate than their male colleagues. Of those who do assume a faculty position, female faculty members report higher levels of burnout, often attributable to gender-specific difficulties in clinical expectations and maintenance of work-life balance. Many of these struggles are attributable to issues that are amenable to supportive policies, but these policies are inconsistent in their availability and practice. This commentary presents evidence for inconsistencies in the day-to-day experience of female faculty members, and proposes solutions for the mitigation of the challenges experienced more often by female faculty members with the goal of diversifying and strengthening academic medicine.
Non linear system become linear system
Petre Bucur
2007-01-01
Full Text Available The present paper refers to the theory and the practice of the systems regarding non-linear systems and their applications. We aimed the integration of these systems to elaborate their response as well as to highlight some outstanding features.
Linear motor coil assembly and linear motor
2009-01-01
An ironless linear motor (5) comprising a magnet track (53) and a coil assembly (50) operating in cooperation with said magnet track (53) and having a plurality of concentrated multi-turn coils (31 a-f, 41 a-d, 51 a-k), wherein the end windings (31E) of the coils (31 a-f, 41 a-e) are substantially
Materials Delivered by Member States
1966-01-01
The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 31 December 1965 in compliance with requests the Agency had made under Article IX. D. Part III contains information about materials which had not been delivered by 31 December but which had been allocated, in accordance with Article XI. F. 1 of the Statute, to approved Agency projects for which project arrangements were in force on that date
Materials Delivered by Member States
1965-01-01
The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 31 December 1964 in compliance with requests the Agency had made under Article IX. D. Part II contains information about materials which had not been delivered by 31 December but which had been allocated, in accordance with Article XI. F. 1 of the Statute, to approved Agency projects for which project arrangements were in force on that date
Materials Delivered by Member States
1968-01-01
The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 30 June 1968 in compliance with requests the Agency had made under Article IX,D. Part II contains information about materials which had not been delivered by 30 June 1968 but which had been allocated, in accordance with Article XI.F.I of the Statute, to approved Agency projects for which project arrangements were in force on that date
Method for brazing together planar and nonplanar metal members
Hammersand, F.G.; Witkowski, A.J.
1985-01-01
The invention relates to a method and apparatus for brazing two metal members together, at least one of which is nonplanar, in a brazing furnace using a substantially pure brazing material. The method comprises the steps of utilizing a brazing fixture to hold the two metal members in tangential relation to one another along a portion of each member so that a cavity is formed adjacent to the contacting portions. A braze material is then positioned within the cavity. The braze fixture, the metal members, and the braze material are then placed in a brazing furnace. A heat shield is then placed over the braze fixture, the metal members, and the braze material to shield the braze material from direct furnace radiation. The furnace temperature is linearly increased at a rate of about 180 0 C. per hour until a temperature of 350 0 C. is achieved. Heat is transferred by conduction from the metal members to the braze material to cause the braze material to melt. Some material from the metal members slowly diffuses into the braze material forming a braze joint. The furnace is rapidly cooled to room temperature using nitrogen gas. The brazed assemblies made according to this method are superior to assemblies formed by heliarc welding
Wiedemann, H.
1981-11-01
Since no linear colliders have been built yet it is difficult to know at what energy the linear cost scaling of linear colliders drops below the quadratic scaling of storage rings. There is, however, no doubt that a linear collider facility for a center of mass energy above say 500 GeV is significantly cheaper than an equivalent storage ring. In order to make the linear collider principle feasible at very high energies a number of problems have to be solved. There are two kinds of problems: one which is related to the feasibility of the principle and the other kind of problems is associated with minimizing the cost of constructing and operating such a facility. This lecture series describes the problems and possible solutions. Since the real test of a principle requires the construction of a prototype I will in the last chapter describe the SLC project at the Stanford Linear Accelerator Center.
Blyth, T S
2002-01-01
Basic Linear Algebra is a text for first year students leading from concrete examples to abstract theorems, via tutorial-type exercises. More exercises (of the kind a student may expect in examination papers) are grouped at the end of each section. The book covers the most important basics of any first course on linear algebra, explaining the algebra of matrices with applications to analytic geometry, systems of linear equations, difference equations and complex numbers. Linear equations are treated via Hermite normal forms which provides a successful and concrete explanation of the notion of linear independence. Another important highlight is the connection between linear mappings and matrices leading to the change of basis theorem which opens the door to the notion of similarity. This new and revised edition features additional exercises and coverage of Cramer's rule (omitted from the first edition). However, it is the new, extra chapter on computer assistance that will be of particular interest to readers:...
Wiedemann, H.
1981-11-01
Since no linear colliders have been built yet it is difficult to know at what energy the linear cost scaling of linear colliders drops below the quadratic scaling of storage rings. There is, however, no doubt that a linear collider facility for a center of mass energy above say 500 GeV is significantly cheaper than an equivalent storage ring. In order to make the linear collider principle feasible at very high energies a number of problems have to be solved. There are two kinds of problems: one which is related to the feasibility of the principle and the other kind of problems is associated with minimizing the cost of constructing and operating such a facility. This lecture series describes the problems and possible solutions. Since the real test of a principle requires the construction of a prototype I will in the last chapter describe the SLC project at the Stanford Linear Accelerator Center
Matrices and linear transformations
Cullen, Charles G
1990-01-01
""Comprehensive . . . an excellent introduction to the subject."" - Electronic Engineer's Design Magazine.This introductory textbook, aimed at sophomore- and junior-level undergraduates in mathematics, engineering, and the physical sciences, offers a smooth, in-depth treatment of linear algebra and matrix theory. The major objects of study are matrices over an arbitrary field. Contents include Matrices and Linear Systems; Vector Spaces; Determinants; Linear Transformations; Similarity: Part I and Part II; Polynomials and Polynomial Matrices; Matrix Analysis; and Numerical Methods. The first
Efficient Non Linear Loudspeakers
Petersen, Bo R.; Agerkvist, Finn T.
2006-01-01
Loudspeakers have traditionally been designed to be as linear as possible. However, as techniques for compensating non linearities are emerging, it becomes possible to use other design criteria. This paper present and examines a new idea for improving the efficiency of loudspeakers at high levels...... by changing the voice coil layout. This deliberate non-linear design has the benefit that a smaller amplifier can be used, which has the benefit of reducing system cost as well as reducing power consumption....
Faraway, Julian J
2014-01-01
A Hands-On Way to Learning Data AnalysisPart of the core of statistics, linear models are used to make predictions and explain the relationship between the response and the predictors. Understanding linear models is crucial to a broader competence in the practice of statistics. Linear Models with R, Second Edition explains how to use linear models in physical science, engineering, social science, and business applications. The book incorporates several improvements that reflect how the world of R has greatly expanded since the publication of the first edition.New to the Second EditionReorganiz
Carr, Joseph
1996-01-01
The linear IC market is large and growing, as is the demand for well trained technicians and engineers who understand how these devices work and how to apply them. Linear Integrated Circuits provides in-depth coverage of the devices and their operation, but not at the expense of practical applications in which linear devices figure prominently. This book is written for a wide readership from FE and first degree students, to hobbyists and professionals.Chapter 1 offers a general introduction that will provide students with the foundations of linear IC technology. From chapter 2 onwa
Fault tolerant linear actuator
Tesar, Delbert
2004-09-14
In varying embodiments, the fault tolerant linear actuator of the present invention is a new and improved linear actuator with fault tolerance and positional control that may incorporate velocity summing, force summing, or a combination of the two. In one embodiment, the invention offers a velocity summing arrangement with a differential gear between two prime movers driving a cage, which then drives a linear spindle screw transmission. Other embodiments feature two prime movers driving separate linear spindle screw transmissions, one internal and one external, in a totally concentric and compact integrated module.
Superconducting linear accelerator cryostat
Ben-Zvi, I.; Elkonin, B.V.; Sokolowski, J.S.
1984-01-01
A large vertical cryostat for a superconducting linear accelerator using quarter wave resonators has been developed. The essential technical details, operational experience and performance are described. (author)
ALA Salary Survey: Personal Members
American Libraries, 1971
1971-01-01
A survey of the members of the American Library Association revealed that the principal salary determinants are academic degree, type of employer and sex. The obvious differences in the earnings of men and women is not only found in the early experience years but any narrowing which does take place in the wage gap seems to take place at the…
Slovenia joins IPPOG as member
'marcelloni, claudia
2018-01-01
Slovenia became an official member of IPPOG on 19 April 2018. The MOU was signed by the head of Particle Physics Department at Jozef Stefan Institute representing Slovenia participation at IPPOG. Andrej Gorišek, country representative for Slovenia in IPPOG, brought the document to the meeting in Italy where IPPOG chairs signed it, confirming Slovenia membership to the collaboration.
Patten, B.C.
1983-04-01
Two issues concerning linearity or nonlinearity of natural systems are considered. Each is related to one of the two alternative defining properties of linear systems, superposition and decomposition. Superposition exists when a linear combination of inputs to a system results in the same linear combination of outputs that individually correspond to the original inputs. To demonstrate this property it is necessary that all initial states and inputs of the system which impinge on the output in question be included in the linear combination manipulation. As this is difficult or impossible to do with real systems of any complexity, nature appears nonlinear even though it may be linear. A linear system that displays nonlinear behavior for this reason is termed pseudononlinear. The decomposition property exists when the dynamic response of a system can be partitioned into an input-free portion due to state plus a state-free portion due to input. This is a characteristic of all linear systems, but not of nonlinear systems. Without the decomposition property, it is not possible to distinguish which portions of a system's behavior are due to innate characteristics (self) vs. outside conditions (environment), which is an important class of questions in biology and ecology. Some philosophical aspects of these findings are then considered. It is suggested that those ecologists who hold to the view that organisms and their environments are separate entities are in effect embracing a linear view of nature, even though their belief systems and mathematical models tend to be nonlinear. On the other hand, those who consider that organism-environment complex forms a single inseparable unit are implictly involved in non-linear thought, which may be in conflict with the linear modes and models that some of them use. The need to rectify these ambivalences on the part of both groups is indicated.
Linear colliders - prospects 1985
Rees, J.
1985-06-01
We discuss the scaling laws of linear colliders and their consequences for accelerator design. We then report on the SLAC Linear Collider project and comment on experience gained on that project and its application to future colliders. 9 refs., 2 figs
Richter, B.
1985-01-01
A report is given on the goals and progress of the SLAC Linear Collider. The author discusses the status of the machine and the detectors and give an overview of the physics which can be done at this new facility. He also gives some ideas on how (and why) large linear colliders of the future should be built
Rogner, H.H.
1989-01-01
The submitted sections on linear programming are extracted from 'Theorie und Technik der Planung' (1978) by W. Blaas and P. Henseler and reformulated for presentation at the Workshop. They consider a brief introduction to the theory of linear programming and to some essential aspects of the SIMPLEX solution algorithm for the purposes of economic planning processes. 1 fig
Rowe, C.H.; Wilton, M.S. de.
1979-01-01
An improved recirculating electron beam linear accelerator of the racetrack type is described. The system comprises a beam path of four straight legs with four Pretzel bending magnets at the end of each leg to direct the beam into the next leg of the beam path. At least one of the beam path legs includes a linear accelerator. (UK)
Understanding Heterogeneous Preferences of Cooperative Members
Kalogeras, N.; Pennings, J.M.E.; Lans, van der I.A.; Garcia, P.; Dijk, van G.
2009-01-01
We study the heterogeneity in the preference structure of cooperative members. Using conjoint analysis the utility that members attach to intra-organizational and strategic attributes of their cooperative is elicited. Recognizing that members are not homogenous, a concomitant finitemixture
Semidefinite linear complementarity problems
Eckhardt, U.
1978-04-01
Semidefinite linear complementarity problems arise by discretization of variational inequalities describing e.g. elastic contact problems, free boundary value problems etc. In the present paper linear complementarity problems are introduced and the theory as well as the numerical treatment of them are described. In the special case of semidefinite linear complementarity problems a numerical method is presented which combines the advantages of elimination and iteration methods without suffering from their drawbacks. This new method has very attractive properties since it has a high degree of invariance with respect to the representation of the set of all feasible solutions of a linear complementarity problem by linear inequalities. By means of some practical applications the properties of the new method are demonstrated. (orig.) [de
Axler, Sheldon
2015-01-01
This best-selling textbook for a second course in linear algebra is aimed at undergrad math majors and graduate students. The novel approach taken here banishes determinants to the end of the book. The text focuses on the central goal of linear algebra: understanding the structure of linear operators on finite-dimensional vector spaces. The author has taken unusual care to motivate concepts and to simplify proofs. A variety of interesting exercises in each chapter helps students understand and manipulate the objects of linear algebra. The third edition contains major improvements and revisions throughout the book. More than 300 new exercises have been added since the previous edition. Many new examples have been added to illustrate the key ideas of linear algebra. New topics covered in the book include product spaces, quotient spaces, and dual spaces. Beautiful new formatting creates pages with an unusually pleasant appearance in both print and electronic versions. No prerequisites are assumed other than the ...
Handbook on linear motor application
1988-10-01
This book guides the application for Linear motor. It lists classification and speciality of Linear Motor, terms of linear-induction motor, principle of the Motor, types on one-side linear-induction motor, bilateral linear-induction motor, linear-DC Motor on basic of the motor, linear-DC Motor for moving-coil type, linear-DC motor for permanent-magnet moving type, linear-DC motor for electricity non-utility type, linear-pulse motor for variable motor, linear-pulse motor for permanent magneto type, linear-vibration actuator, linear-vibration actuator for moving-coil type, linear synchronous motor, linear electromagnetic motor, linear electromagnetic solenoid, technical organization and magnetic levitation and linear motor and sensor.
Community Members Draw the Line
Gregory Freeland
2014-06-01
Full Text Available This study investigates whether a community-based task force’s redistricting plan in Ventura County, California, positively affected fair representation, social equity issues, community interests, and the electoral process. Examination and evaluation of the organizational strategies and collaborations involved in the task force’s redistricting process find that the Board of Supervisors districts that members of the community drew were successful in improving and maintaining fair representation. This finding is based on comparing supervisorial votes and policies with community members’ votes on state propositions and local measures, in addition to conducting interviews with task force members, politicians, and community activists. This study finds that citizen participation in governmental processes improves overall community health and political participation.
Power reactors in member states
1975-01-01
This is the first issue of a periodical computer-based listing of civilian nuclear power reactors in the Member States of the IAEA, presenting the situation as of 1 April 1975. It is intended as a replacement for the Agency's previous annual publication of ''Power and Research Reactors in Member States''. In the new format, the listing contains more information about power reactors in operation, under construction, planned and shut down. As far as possible all the basic design data relating to reactors in operation have been included. In future these data will be included also for other power reactors, so that the publication will serve to give a clear picture of the technical progress achieved. Test and research reactors and critical facilities are no longer listed. Of interest to nuclear power planners, nuclear system designers, nuclear plant operators and interested professional engineers and scientists
Staff Association
2018-01-01
Evolution 2, your specialist for Outdoor Adventures Be it for a ski lesson, a parachute jump or for a mountain bike descent, come live an unforgettable experience with our outdoor specialists. Benefit from a 10 % discount on all activities: Offer is open to SA members and their family members living in the same household, upon presentation of the membership card. Offer available for all bookings made between 1 June 2018 and 30 May 2019. Offer available on all the Evoltion2 sites. A wide range of summer and winter activities. More information on http://evolution2.com/ Contact and reservation : +33 (0)4.50.02.63.35 management@evolution2.com
Materials Delivered by Member States
1962-01-01
The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered up to 30 September 1962 by Member States in compliance with requests the Agency has made under Article IX. D. Part II contains information about materials which have not yet been delivered but which have been allocated, in accordance with Article XI. F. 1 of the Statute, to approved Agency projects for which project agreements were in force on 30 September 1962. Reports on subsequent deliveries of materials and revised information about allocated but undelivered materials will be issued from time to time
Communication Among Melanoma Family Members
Bowen, Deborah J; Albrecht, Terrance; Hay, Jennifer; Eggly, Susan; Harris-Wei, Julie; Meischke, Hendrika; Burke, Wylie
2017-01-01
Interventions to improve communication among family members may facilitate information flow about familial risk and preventive health behaviors. This is a secondary analysis of the effects of an interactive website intervention aimed at increasing communication frequency and agreement about health risk among melanoma families. Participants were family units, consisting of one family member with melanoma identified from a previous research study (the case) and an additional first degree relative and a parent of a child 0–17. Family triads were randomized to receive access to the website intervention or to serve as control families. Family communication frequency and agreement about melanoma prevention behaviors and beliefs were measured at baseline and again at one year post randomization. Intervention participants of all three types significantly increased the frequency of communication to their first degree relatives (Parents, siblings, children; range =14–18 percentage points; all pcommunication about cancer risk. PMID:28248624
AGU has recently established a new customer "support line"—solutions@agu.org—as the point of contact on AGU's staff for members and other individual constituents who have not been able to resolve issues or get questions answered promptly or to their satisfaction through customary channels.Over the past year, there have been many changes at AGU. Unfortunately—and perhaps as a result of these changes—communication with members and individual constituents has suffered. Some individuals report, for example, that e-mail messages are not answered to their satisfaction, or in a timely manner. Instructions on AGU's Web site are unclear in some areas. Problems related specifically to the transition to electronic publishing are cropping up.
Towards mobile staff members management
Encheva, Sylvia
2017-07-01
Todays project management requires a number of abilities which involve finding quick solutions to shortage of staff members with possession of specific qualities. When persons with team responsibilities are under pressure or due to various circumstances are unable to perform exhaustive search in databases, an interactive visualization tool can come in quite handy in finding good solutions unforeseen occurrences. In particular we propose application of selected graphs for facilitating mobile human resource management.
Shielding member for thermonuclear device
Onozuka, Masanori
1997-06-30
In a thermonuclear device for shielding fast neutrons by shielding members disposed in a shielding vessel (vacuum vessel and structures such as a blanket disposed in the vacuum vessel), the shielding member comprises a large number of shielding wires formed fine and short so as to have elasticity. The shielding wires are sealed in a shielding vessel together with water, and when the width of the shielding vessel is changed, the shielding wires follow after the change of the width while elastically deforming in the shielding vessel, so that great stress and deformation are not formed thereby enabling to improve reliability. In addition, the length, the diameter and the shape of each of the shielding wires can be selected in accordance with the shielding space of the shielding vessel. Even if the shape of the shielding vessel is complicated, the shielding wires can be inserted easily. Accordingly, the filling rate of the shielding members can be changed easily. It can be produced more easily compared with a conventional spherical pebbles. It can be produced more easily than existent spherical shielding pebbles thereby enabling to reduce the production cost. (N.H.)
Linear ubiquitination in immunity.
Shimizu, Yutaka; Taraborrelli, Lucia; Walczak, Henning
2015-07-01
Linear ubiquitination is a post-translational protein modification recently discovered to be crucial for innate and adaptive immune signaling. The function of linear ubiquitin chains is regulated at multiple levels: generation, recognition, and removal. These chains are generated by the linear ubiquitin chain assembly complex (LUBAC), the only known ubiquitin E3 capable of forming the linear ubiquitin linkage de novo. LUBAC is not only relevant for activation of nuclear factor-κB (NF-κB) and mitogen-activated protein kinases (MAPKs) in various signaling pathways, but importantly, it also regulates cell death downstream of immune receptors capable of inducing this response. Recognition of the linear ubiquitin linkage is specifically mediated by certain ubiquitin receptors, which is crucial for translation into the intended signaling outputs. LUBAC deficiency results in attenuated gene activation and increased cell death, causing pathologic conditions in both, mice, and humans. Removal of ubiquitin chains is mediated by deubiquitinases (DUBs). Two of them, OTULIN and CYLD, are constitutively associated with LUBAC. Here, we review the current knowledge on linear ubiquitination in immune signaling pathways and the biochemical mechanisms as to how linear polyubiquitin exerts its functions distinctly from those of other ubiquitin linkage types. © 2015 The Authors. Immunological Reviews Published by John Wiley & Sons Ltd.
Krivonos, S.O.; Sorin, A.S.
1994-06-01
We show that the Zamolodchikov's and Polyakov-Bershadsky nonlinear algebras W 3 and W (2) 3 can be embedded as subalgebras into some linear algebras with finite set of currents. Using these linear algebras we find new field realizations of W (2) 3 and W 3 which could be a starting point for constructing new versions of W-string theories. We also reveal a number of hidden relationships between W 3 and W (2) 3 . We conjecture that similar linear algebras can exist for other W-algebra as well. (author). 10 refs
Schneider, Hans
1989-01-01
Linear algebra is one of the central disciplines in mathematics. A student of pure mathematics must know linear algebra if he is to continue with modern algebra or functional analysis. Much of the mathematics now taught to engineers and physicists requires it.This well-known and highly regarded text makes the subject accessible to undergraduates with little mathematical experience. Written mainly for students in physics, engineering, economics, and other fields outside mathematics, the book gives the theory of matrices and applications to systems of linear equations, as well as many related t
Linearity in Process Languages
Nygaard, Mikkel; Winskel, Glynn
2002-01-01
The meaning and mathematical consequences of linearity (managing without a presumed ability to copy) are studied for a path-based model of processes which is also a model of affine-linear logic. This connection yields an affine-linear language for processes, automatically respecting open......-map bisimulation, in which a range of process operations can be expressed. An operational semantics is provided for the tensor fragment of the language. Different ways to make assemblies of processes lead to different choices of exponential, some of which respect bisimulation....
Amir-Moez, A R; Sneddon, I N
1962-01-01
Elements of Linear Space is a detailed treatment of the elements of linear spaces, including real spaces with no more than three dimensions and complex n-dimensional spaces. The geometry of conic sections and quadric surfaces is considered, along with algebraic structures, especially vector spaces and transformations. Problems drawn from various branches of geometry are given.Comprised of 12 chapters, this volume begins with an introduction to real Euclidean space, followed by a discussion on linear transformations and matrices. The addition and multiplication of transformations and matrices a
Weisberg, Sanford
2013-01-01
Praise for the Third Edition ""...this is an excellent book which could easily be used as a course text...""-International Statistical Institute The Fourth Edition of Applied Linear Regression provides a thorough update of the basic theory and methodology of linear regression modeling. Demonstrating the practical applications of linear regression analysis techniques, the Fourth Edition uses interesting, real-world exercises and examples. Stressing central concepts such as model building, understanding parameters, assessing fit and reliability, and drawing conclusions, the new edition illus
Callier, Frank M.; Desoer, Charles A.
1991-01-01
The aim of this book is to provide a systematic and rigorous access to the main topics of linear state-space system theory in both the continuous-time case and the discrete-time case; and the I/O description of linear systems. The main thrusts of the work are the analysis of system descriptions and derivations of their properties, LQ-optimal control, state feedback and state estimation, and MIMO unity-feedback systems.
7 CFR 1425.19 - Member cooperatives.
2010-01-01
... 7 Agriculture 10 2010-01-01 2010-01-01 false Member cooperatives. 1425.19 Section 1425.19... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COOPERATIVE MARKETING ASSOCIATIONS § 1425.19 Member cooperatives. A CMA may obtain loans or LDP's on behalf of a member cooperative when the member...
Blyth, T S
2002-01-01
Most of the introductory courses on linear algebra develop the basic theory of finite dimensional vector spaces, and in so doing relate the notion of a linear mapping to that of a matrix. Generally speaking, such courses culminate in the diagonalisation of certain matrices and the application of this process to various situations. Such is the case, for example, in our previous SUMS volume Basic Linear Algebra. The present text is a continuation of that volume, and has the objective of introducing the reader to more advanced properties of vector spaces and linear mappings, and consequently of matrices. For readers who are not familiar with the contents of Basic Linear Algebra we provide an introductory chapter that consists of a compact summary of the prerequisites for the present volume. In order to consolidate the student's understanding we have included a large num ber of illustrative and worked examples, as well as many exercises that are strategi cally placed throughout the text. Solutions to the ex...
Mamyrin, B.A.; Shmikk, D.V.
1979-01-01
A description and operating principle of a linear mass reflectron with V-form trajectory of ion motion -a new non-magnetic time-of-flight mass spectrometer with high resolution are presented. The ion-optical system of the device consists of an ion source with ionization by electron shock, of accelerating gaps, reflector gaps, a drift space and ion detector. Ions move in the linear mass refraction along the trajectories parallel to the axis of the analyzer chamber. The results of investigations into the experimental device are given. With an ion drift length of 0.6 m the device resolution is 1200 with respect to the peak width at half-height. Small-sized mass spectrometric transducers with high resolution and sensitivity may be designed on the base of the linear mass reflectron principle
Olver, Peter J
2018-01-01
This textbook develops the essential tools of linear algebra, with the goal of imparting technique alongside contextual understanding. Applications go hand-in-hand with theory, each reinforcing and explaining the other. This approach encourages students to develop not only the technical proficiency needed to go on to further study, but an appreciation for when, why, and how the tools of linear algebra can be used across modern applied mathematics. Providing an extensive treatment of essential topics such as Gaussian elimination, inner products and norms, and eigenvalues and singular values, this text can be used for an in-depth first course, or an application-driven second course in linear algebra. In this second edition, applications have been updated and expanded to include numerical methods, dynamical systems, data analysis, and signal processing, while the pedagogical flow of the core material has been improved. Throughout, the text emphasizes the conceptual connections between each application and the un...
Banach, S
1987-01-01
This classic work by the late Stefan Banach has been translated into English so as to reach a yet wider audience. It contains the basics of the algebra of operators, concentrating on the study of linear operators, which corresponds to that of the linear forms a1x1 + a2x2 + ... + anxn of algebra.The book gathers results concerning linear operators defined in general spaces of a certain kind, principally in Banach spaces, examples of which are: the space of continuous functions, that of the pth-power-summable functions, Hilbert space, etc. The general theorems are interpreted in various mathematical areas, such as group theory, differential equations, integral equations, equations with infinitely many unknowns, functions of a real variable, summation methods and orthogonal series.A new fifty-page section (``Some Aspects of the Present Theory of Banach Spaces'''') complements this important monograph.
Høskuldsson, Agnar
1996-01-01
Determination of the proper dimension of a given linear model is one of the most important tasks in the applied modeling work. We consider here eight criteria that can be used to determine the dimension of the model, or equivalently, the number of components to use in the model. Four of these cri......Determination of the proper dimension of a given linear model is one of the most important tasks in the applied modeling work. We consider here eight criteria that can be used to determine the dimension of the model, or equivalently, the number of components to use in the model. Four...... the basic problems in determining the dimension of linear models. Then each of the eight measures are treated. The results are illustrated by examples....
Linear programming using Matlab
Ploskas, Nikolaos
2017-01-01
This book offers a theoretical and computational presentation of a variety of linear programming algorithms and methods with an emphasis on the revised simplex method and its components. A theoretical background and mathematical formulation is included for each algorithm as well as comprehensive numerical examples and corresponding MATLAB® code. The MATLAB® implementations presented in this book are sophisticated and allow users to find solutions to large-scale benchmark linear programs. Each algorithm is followed by a computational study on benchmark problems that analyze the computational behavior of the presented algorithms. As a solid companion to existing algorithmic-specific literature, this book will be useful to researchers, scientists, mathematical programmers, and students with a basic knowledge of linear algebra and calculus. The clear presentation enables the reader to understand and utilize all components of simplex-type methods, such as presolve techniques, scaling techniques, pivoting ru...
Anon.
1994-01-01
The aim of the TESLA (TeV Superconducting Linear Accelerator) collaboration (at present 19 institutions from seven countries) is to establish the technology for a high energy electron-positron linear collider using superconducting radiofrequency cavities to accelerate its beams. Another basic goal is to demonstrate that such a collider can meet its performance goals in a cost effective manner. For this the TESLA collaboration is preparing a 500 MeV superconducting linear test accelerator at the DESY Laboratory in Hamburg. This TTF (TESLA Test Facility) consists of four cryomodules, each approximately 12 m long and containing eight 9-cell solid niobium cavities operating at a frequency of 1.3 GHz
Linearly Adjustable International Portfolios
Fonseca, R. J.; Kuhn, D.; Rustem, B.
2010-09-01
We present an approach to multi-stage international portfolio optimization based on the imposition of a linear structure on the recourse decisions. Multiperiod decision problems are traditionally formulated as stochastic programs. Scenario tree based solutions however can become intractable as the number of stages increases. By restricting the space of decision policies to linear rules, we obtain a conservative tractable approximation to the original problem. Local asset prices and foreign exchange rates are modelled separately, which allows for a direct measure of their impact on the final portfolio value.
Linearly Adjustable International Portfolios
Fonseca, R. J.; Kuhn, D.; Rustem, B.
2010-01-01
We present an approach to multi-stage international portfolio optimization based on the imposition of a linear structure on the recourse decisions. Multiperiod decision problems are traditionally formulated as stochastic programs. Scenario tree based solutions however can become intractable as the number of stages increases. By restricting the space of decision policies to linear rules, we obtain a conservative tractable approximation to the original problem. Local asset prices and foreign exchange rates are modelled separately, which allows for a direct measure of their impact on the final portfolio value.
Barkman, W.E.; Adams, W.Q.; Berrier, B.R.
1978-01-01
A linear induction motor has been operated on a test bed with a feedback pulse resolution of 5 nm (0.2 μin). Slewing tests with this slide drive have shown positioning errors less than or equal to 33 nm (1.3 μin) at feedrates between 0 and 25.4 mm/min (0-1 ipm). A 0.86-m (34-in)-stroke linear motor is being investigated, using the SPACO machine as a test bed. Initial results were encouraging, and work is continuing to optimize the servosystem compensation
Hogben, Leslie
2013-01-01
With a substantial amount of new material, the Handbook of Linear Algebra, Second Edition provides comprehensive coverage of linear algebra concepts, applications, and computational software packages in an easy-to-use format. It guides you from the very elementary aspects of the subject to the frontiers of current research. Along with revisions and updates throughout, the second edition of this bestseller includes 20 new chapters.New to the Second EditionSeparate chapters on Schur complements, additional types of canonical forms, tensors, matrix polynomials, matrix equations, special types of
Linear Algebra Thoroughly Explained
Vujičić, Milan
2008-01-01
Linear Algebra Thoroughly Explained provides a comprehensive introduction to the subject suitable for adoption as a self-contained text for courses at undergraduate and postgraduate level. The clear and comprehensive presentation of the basic theory is illustrated throughout with an abundance of worked examples. The book is written for teachers and students of linear algebra at all levels and across mathematics and the applied sciences, particularly physics and engineering. It will also be an invaluable addition to research libraries as a comprehensive resource book for the subject.
2013-05-10
AND VICTIM- ~ vAP BLAMING 4. AMERICA, LINEARLY CYCUCAL AF IMT 1768, 19840901, V5 PREVIOUS EDITION WILL BE USED. C2C Jessica Adams Dr. Brissett...his desires, his failings, and his aspirations follow the same general trend throughout history and throughout cultures. The founding fathers sought
Southworth, B.
1985-01-01
The peak of the construction phase of the Stanford Linear Collider, SLC, to achieve 50 GeV electron-positron collisions has now been passed. The work remains on schedule to attempt colliding beams, initially at comparatively low luminosity, early in 1987. (orig./HSI).
Mafra Neto, F.
1992-01-01
The dose of gamma radiation from a linear source of cesium 137 is obtained, presenting two difficulties: oblique filtration of radiation when cross the platinum wall, in different directions, and dose connection due to the scattering by the material mean of propagation. (C.G.C.)
Resistors Improve Ramp Linearity
Kleinberg, L. L.
1982-01-01
Simple modification to bootstrap ramp generator gives more linear output over longer sweep times. New circuit adds just two resistors, one of which is adjustable. Modification cancels nonlinearities due to variations in load on charging capacitor and due to changes in charging current as the voltage across capacitor increases.
LINEAR COLLIDERS: 1992 workshop
Settles, Ron; Coignet, Guy
1992-01-01
As work on designs for future electron-positron linear colliders pushes ahead at major Laboratories throughout the world in a major international collaboration framework, the LC92 workshop held in Garmisch Partenkirchen this summer, attended by 200 machine and particle physicists, provided a timely focus
Brameier, Markus
2007-01-01
Presents a variant of Genetic Programming that evolves imperative computer programs as linear sequences of instructions, in contrast to the more traditional functional expressions or syntax trees. This book serves as a reference for researchers, but also contains sufficient introduction for students and those who are new to the field
Dobbs, David E.
2013-01-01
A direct method is given for solving first-order linear recurrences with constant coefficients. The limiting value of that solution is studied as "n to infinity." This classroom note could serve as enrichment material for the typical introductory course on discrete mathematics that follows a calculus course.
Takeda, Seishi
1992-01-01
The status of R and D of future e + e - linear colliders proposed by the institutions throughout the world is described including the JLC, NLC, VLEPP, CLIC, DESY/THD and TESLA projects. The parameters and RF sources are discussed. (G.P.) 36 refs.; 1 tab
Finite-dimensional linear algebra
Gockenbach, Mark S
2010-01-01
Some Problems Posed on Vector SpacesLinear equationsBest approximationDiagonalizationSummaryFields and Vector SpacesFields Vector spaces Subspaces Linear combinations and spanning sets Linear independence Basis and dimension Properties of bases Polynomial interpolation and the Lagrange basis Continuous piecewise polynomial functionsLinear OperatorsLinear operatorsMore properties of linear operatorsIsomorphic vector spaces Linear operator equations Existence and uniqueness of solutions The fundamental theorem; inverse operatorsGaussian elimination Newton's method Linear ordinary differential eq
International Focus: Highlighting APPA Members Worldwide
Glazner, Steve, Comp.
2011-01-01
While most APPA member institutions are located in the United States and Canada, there are also 45 of member institutions located internationally--from Australia and New Zealand to Southeast Asia to the Middle East to Europe. This article focuses on four of its international members: (1) American University of Kuwait (AUK); (2) American University…
The Members of the Agency (French Edition)
2013-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.74) is Swaziland, which deposited its instrument of acceptance of the Statute on 15 February 2013. The Attachment hereto shows the dates on which the present 159 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
The Members of the Agency (Spanish Edition)
2013-01-01
The new Member since the last list of Member States was issued (INFCIRC/2/Rev.74) is Swaziland, which deposited its instrument of acceptance of the Statute on 15 February 2013. The Attachment hereto shows the dates on which the present 159 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government
The Analysis of Flexicurity in the EU Members States
Suzana LAPORŠEK
2011-02-01
Full Text Available The purpose of this paper is to present the characteristics of labor markets in the EU Member States in terms of design and implementation of policy components of flexicurity, as well as to examine the relationship between flexicurity and labor productivity. The estimates of the characteristics of labor market flexibility and security, and flexicurity models in the EU are based on the descriptive statistics and cluster analysis. The impact of flexicurity on labor productivity is assessed using principal component analysis and linear regression analysis. The results of empirical analysis point on the existence of considerable differences in labor market flexibility and security across EU Member States. The least successful at simultaneous implementation of flexibility and security are New Member States, showing rigid labor market regulation at very low security of employees. On the other hand, the most balanced flexicurity policies, thus ensuring high levels of flexibility and security, can be found among Scandinavian countries. The latter, together with United Kingdom and Ireland, also achieve the highest macroeconomic performance. The positive impact of flexicurity on macroeconomic performance was confirmed by linear regression analysis, which showed a positive relationship between indicators of security in the labor market and labor productivity.
Linearity and Non-linearity of Photorefractive effect in Materials ...
In this paper we have studied the Linearity and Non-linearity of Photorefractive effect in materials using the band transport model. For low light beam intensities the change in the refractive index is proportional to the electric field for linear optics while for non- linear optics the change in refractive index is directly proportional ...
Linearly Refined Session Types
Pedro Baltazar
2012-11-01
Full Text Available Session types capture precise protocol structure in concurrent programming, but do not specify properties of the exchanged values beyond their basic type. Refinement types are a form of dependent types that can address this limitation, combining types with logical formulae that may refer to program values and can constrain types using arbitrary predicates. We present a pi calculus with assume and assert operations, typed using a session discipline that incorporates refinement formulae written in a fragment of Multiplicative Linear Logic. Our original combination of session and refinement types, together with the well established benefits of linearity, allows very fine-grained specifications of communication protocols in which refinement formulae are treated as logical resources rather than persistent truths.
Kuznetsov, N.; Maz'ya, V.; Vainberg, B.
2002-08-01
This book gives a self-contained and up-to-date account of mathematical results in the linear theory of water waves. The study of waves has many applications, including the prediction of behavior of floating bodies (ships, submarines, tension-leg platforms etc.), the calculation of wave-making resistance in naval architecture, and the description of wave patterns over bottom topography in geophysical hydrodynamics. The first section deals with time-harmonic waves. Three linear boundary value problems serve as the approximate mathematical models for these types of water waves. The next section uses a plethora of mathematical techniques in the investigation of these three problems. The techniques used in the book include integral equations based on Green's functions, various inequalities between the kinetic and potential energy and integral identities which are indispensable for proving the uniqueness theorems. The so-called inverse procedure is applied to constructing examples of non-uniqueness, usually referred to as 'trapped nodes.'
The International Linear Collider
List Benno
2014-04-01
Full Text Available The International Linear Collider (ILC is a proposed e+e− linear collider with a centre-of-mass energy of 200–500 GeV, based on superconducting RF cavities. The ILC would be an ideal machine for precision studies of a light Higgs boson and the top quark, and would have a discovery potential for new particles that is complementary to that of LHC. The clean experimental conditions would allow the operation of detectors with extremely good performance; two such detectors, ILD and SiD, are currently being designed. Both make use of novel concepts for tracking and calorimetry. The Japanese High Energy Physics community has recently recommended to build the ILC in Japan.
The International Linear Collider
List, Benno
2014-04-01
The International Linear Collider (ILC) is a proposed e+e- linear collider with a centre-of-mass energy of 200-500 GeV, based on superconducting RF cavities. The ILC would be an ideal machine for precision studies of a light Higgs boson and the top quark, and would have a discovery potential for new particles that is complementary to that of LHC. The clean experimental conditions would allow the operation of detectors with extremely good performance; two such detectors, ILD and SiD, are currently being designed. Both make use of novel concepts for tracking and calorimetry. The Japanese High Energy Physics community has recently recommended to build the ILC in Japan.
Høskuldsson, Agnar
1996-01-01
Determination of the proper dimension of a given linear model is one of the most important tasks in the applied modeling work. We consider here eight criteria that can be used to determine the dimension of the model, or equivalently, the number of components to use in the model. Four...... the basic problems in determining the dimension of linear models. Then each of the eight measures are treated. The results are illustrated by examples....... of these criteria are widely used ones, while the remaining four are ones derived from the H-principle of mathematical modeling. Many examples from practice show that the criteria derived from the H-principle function better than the known and popular criteria for the number of components. We shall briefly review...
Goldowsky, Michael P. (Inventor)
1987-01-01
A reciprocating linear motor is formed with a pair of ring-shaped permanent magnets having opposite radial polarizations, held axially apart by a nonmagnetic yoke, which serves as an axially displaceable armature assembly. A pair of annularly wound coils having axial lengths which differ from the axial lengths of the permanent magnets are serially coupled together in mutual opposition and positioned with an outer cylindrical core in axial symmetry about the armature assembly. One embodiment includes a second pair of annularly wound coils serially coupled together in mutual opposition and an inner cylindrical core positioned in axial symmetry inside the armature radially opposite to the first pair of coils. Application of a potential difference across a serial connection of the two pairs of coils creates a current flow perpendicular to the magnetic field created by the armature magnets, thereby causing limited linear displacement of the magnets relative to the coils.
Henneaux, Marc; Teitelboim, Claudio
2005-01-01
We show that duality transformations of linearized gravity in four dimensions, i.e., rotations of the linearized Riemann tensor and its dual into each other, can be extended to the dynamical fields of the theory so as to be symmetries of the action and not just symmetries of the equations of motion. Our approach relies on the introduction of two superpotentials, one for the spatial components of the spin-2 field and the other for their canonically conjugate momenta. These superpotentials are two-index, symmetric tensors. They can be taken to be the basic dynamical fields and appear locally in the action. They are simply rotated into each other under duality. In terms of the superpotentials, the canonical generator of duality rotations is found to have a Chern-Simons-like structure, as in the Maxwell case
Phinney, N.
1992-01-01
The SLAC Linear Collider has begun a new era of operation with the SLD detector. During 1991 there was a first engineering run for the SLD in parallel with machine improvements to increase luminosity and reliability. For the 1992 run, a polarized electron source was added and more than 10,000 Zs with an average of 23% polarization have been logged by the SLD. This paper discusses the performance of the SLC in 1991 and 1992 and the technical advances that have produced higher luminosity. Emphasis will be placed on issues relevant to future linear colliders such as producing and maintaining high current, low emittance beams and focusing the beams to the micron scale for collisions. (Author) tab., 2 figs., 18 refs
Linear waves and instabilities
Bers, A.
1975-01-01
The electrodynamic equations for small-amplitude waves and their dispersion relation in a homogeneous plasma are outlined. For such waves, energy and momentum, and their flow and transformation, are described. Perturbation theory of waves is treated and applied to linear coupling of waves, and the resulting instabilities from such interactions between active and passive waves. Linear stability analysis in time and space is described where the time-asymptotic, time-space Green's function for an arbitrary dispersion relation is developed. The perturbation theory of waves is applied to nonlinear coupling, with particular emphasis on pump-driven interactions of waves. Details of the time--space evolution of instabilities due to coupling are given. (U.S.)
Extended linear chain compounds
Linear chain substances span a large cross section of contemporary chemistry ranging from covalent polymers, to organic charge transfer com plexes to nonstoichiometric transition metal coordination complexes. Their commonality, which coalesced intense interest in the theoretical and exper imental solid state physics/chemistry communities, was based on the obser vation that these inorganic and organic polymeric substrates exhibit striking metal-like electrical and optical properties. Exploitation and extension of these systems has led to the systematic study of both the chemistry and physics of highly and poorly conducting linear chain substances. To gain a salient understanding of these complex materials rich in anomalous aniso tropic electrical, optical, magnetic, and mechanical properties, the conver gence of diverse skills and talents was required. The constructive blending of traditionally segregated disciplines such as synthetic and physical organic, inorganic, and polymer chemistry, crystallog...
Lexan Linear Shaped Charge Holder with Magnets and Backing Plate
Maples, Matthew W.; Dutton, Maureen L.; Hacker, Scott C.; Dean, Richard J.; Kidd, Nicholas; Long, Chris; Hicks, Robert C.
2013-01-01
A method was developed for cutting a fabric structural member in an inflatable module, without damaging the internal structure of the module, using linear shaped charge. Lexan and magnets are used in a charge holder to precisely position the linear shaped charge over the desired cut area. Two types of charge holders have been designed, each with its own backing plate. One holder cuts fabric straps in the vertical configuration, and the other charge holder cuts fabric straps in the horizontal configuration.
Diamond, Jared M.
1966-01-01
1. The relation between osmotic gradient and rate of osmotic water flow has been measured in rabbit gall-bladder by a gravimetric procedure and by a rapid method based on streaming potentials. Streaming potentials were directly proportional to gravimetrically measured water fluxes. 2. As in many other tissues, water flow was found to vary with gradient in a markedly non-linear fashion. There was no consistent relation between the water permeability and either the direction or the rate of water flow. 3. Water flow in response to a given gradient decreased at higher osmolarities. The resistance to water flow increased linearly with osmolarity over the range 186-825 m-osM. 4. The resistance to water flow was the same when the gall-bladder separated any two bathing solutions with the same average osmolarity, regardless of the magnitude of the gradient. In other words, the rate of water flow is given by the expression (Om — Os)/[Ro′ + ½k′ (Om + Os)], where Ro′ and k′ are constants and Om and Os are the bathing solution osmolarities. 5. Of the theories advanced to explain non-linear osmosis in other tissues, flow-induced membrane deformations, unstirred layers, asymmetrical series-membrane effects, and non-osmotic effects of solutes could not explain the results. However, experimental measurements of water permeability as a function of osmolarity permitted quantitative reconstruction of the observed water flow—osmotic gradient curves. Hence non-linear osmosis in rabbit gall-bladder is due to a decrease in water permeability with increasing osmolarity. 6. The results suggest that aqueous channels in the cell membrane behave as osmometers, shrinking in concentrated solutions of impermeant molecules and thereby increasing membrane resistance to water flow. A mathematical formulation of such a membrane structure is offered. PMID:5945254
Fundamentals of linear algebra
Dash, Rajani Ballav
2008-01-01
FUNDAMENTALS OF LINEAR ALGEBRA is a comprehensive Text Book, which can be used by students and teachers of All Indian Universities. The Text has easy, understandable form and covers all topics of UGC Curriculum. There are lots of worked out examples which helps the students in solving the problems without anybody's help. The Problem sets have been designed keeping in view of the questions asked in different examinations.
Sander, K F
1964-01-01
Linear Network Theory covers the significant algebraic aspect of network theory, with minimal reference to practical circuits. The book begins the presentation of network analysis with the exposition of networks containing resistances only, and follows it up with a discussion of networks involving inductance and capacity by way of the differential equations. Classification and description of certain networks, equivalent networks, filter circuits, and network functions are also covered. Electrical engineers, technicians, electronics engineers, electricians, and students learning the intricacies
Non linear viscoelastic models
Agerkvist, Finn T.
2011-01-01
Viscoelastic eects are often present in loudspeaker suspensions, this can be seen in the displacement transfer function which often shows a frequency dependent value below the resonance frequency. In this paper nonlinear versions of the standard linear solid model (SLS) are investigated....... The simulations show that the nonlinear version of the Maxwell SLS model can result in a time dependent small signal stiness while the Kelvin Voight version does not....
Relativistic Linear Restoring Force
Clark, D.; Franklin, J.; Mann, N.
2012-01-01
We consider two different forms for a relativistic version of a linear restoring force. The pair comes from taking Hooke's law to be the force appearing on the right-hand side of the relativistic expressions: d"p"/d"t" or d"p"/d["tau"]. Either formulation recovers Hooke's law in the non-relativistic limit. In addition to these two forces, we…
Superconducting linear colliders
Anon.
1990-01-01
The advantages of superconducting radiofrequency (SRF) for particle accelerators have been demonstrated by successful operation of systems in the TRISTAN and LEP electron-positron collider rings respectively at the Japanese KEK Laboratory and at CERN. If performance continues to improve and costs can be lowered, this would open an attractive option for a high luminosity TeV (1000 GeV) linear collider
Perturbed asymptotically linear problems
Bartolo, R.; Candela, A. M.; Salvatore, A.
2012-01-01
The aim of this paper is investigating the existence of solutions of some semilinear elliptic problems on open bounded domains when the nonlinearity is subcritical and asymptotically linear at infinity and there is a perturbation term which is just continuous. Also in the case when the problem has not a variational structure, suitable procedures and estimates allow us to prove that the number of distinct crtitical levels of the functional associated to the unperturbed problem is "stable" unde...
Miniature linear cooler development
Pruitt, G.R.
1993-01-01
An overview is presented of the status of a family of miniature linear coolers currently under development by Hughes Aircraft Co. for use in hand held, volume limited or power limited infrared applications. These coolers, representing the latest additions to the Hughes family of TOP trademark [twin-opposed piston] linear coolers, have been fabricated and tested in three different configurations. Each configuration is designed to utilize a common compressor assembly resulting in reduced manufacturing costs. The baseline compressor has been integrated with two different expander configurations and has been operated with two different levels of input power. These various configuration combinations offer a wide range of performance and interface characteristics which may be tailored to applications requiring limited power and size without significantly compromising cooler capacity or cooldown characteristics. Key cooler characteristics and test data are summarized for three combinations of cooler configurations which are representative of the versatility of this linear cooler design. Configurations reviewed include the shortened coldfinger [1.50 to 1.75 inches long], limited input power [less than 17 Watts] for low power availability applications; the shortened coldfinger with higher input power for lightweight, higher performance applications; and coldfingers compatible with DoD 0.4 Watt Common Module coolers for wider range retrofit capability. Typical weight of these miniature linear coolers is less than 500 grams for the compressor, expander and interconnecting transfer line. Cooling capacity at 80K at room ambient conditions ranges from 400 mW to greater than 550 mW. Steady state power requirements for maintaining a heat load of 150 mW at 80K has been shown to be less than 8 Watts. Ongoing reliability growth testing is summarized including a review of the latest test article results
Avram Mihai
2017-01-01
Full Text Available The paper presents a linear pneumatic actuator with short working stroke. It consists of a pneumatic motor (a simple stroke cylinder or a membrane chamber, two 2/2 pneumatic distributors “all or nothing” electrically commanded for controlling the intake/outtake flow to/from the active chamber of the motor, a position transducer and a microcontroller. There is also presented the theoretical analysis (mathematical modelling and numerical simulation accomplished.
Avram Mihai; Niţu Constantin; Bucşan Constantin; Grămescu Bogdan
2017-01-01
The paper presents a linear pneumatic actuator with short working stroke. It consists of a pneumatic motor (a simple stroke cylinder or a membrane chamber), two 2/2 pneumatic distributors “all or nothing” electrically commanded for controlling the intake/outtake flow to/from the active chamber of the motor, a position transducer and a microcontroller. There is also presented the theoretical analysis (mathematical modelling and numerical simulation) accomplished.
Scheffel, J.
1984-03-01
The linear Grad-Shafranov equation for a toroidal, axisymmetric plasma is solved analytically. Exact solutions are given in terms of confluent hyper-geometric functions. As an alternative, simple and accurate WKBJ solutions are presented. With parabolic pressure profiles, both hollow and peaked toroidal current density profiles are obtained. As an example the equilibrium of a z-pinch with a square-shaped cross section is derived.(author)
Buttram, M.T.; Ginn, J.W.
1988-06-21
A linear induction accelerator includes a plurality of adder cavities arranged in a series and provided in a structure which is evacuated so that a vacuum inductance is provided between each adder cavity and the structure. An energy storage system for the adder cavities includes a pulsed current source and a respective plurality of bipolar converting networks connected thereto. The bipolar high-voltage, high-repetition-rate square pulse train sets and resets the cavities. 4 figs.
Springer, T A
1998-01-01
"[The first] ten chapters...are an efficient, accessible, and self-contained introduction to affine algebraic groups over an algebraically closed field. The author includes exercises and the book is certainly usable by graduate students as a text or for self-study...the author [has a] student-friendly style… [The following] seven chapters... would also be a good introduction to rationality issues for algebraic groups. A number of results from the literature…appear for the first time in a text." –Mathematical Reviews (Review of the Second Edition) "This book is a completely new version of the first edition. The aim of the old book was to present the theory of linear algebraic groups over an algebraically closed field. Reading that book, many people entered the research field of linear algebraic groups. The present book has a wider scope. Its aim is to treat the theory of linear algebraic groups over arbitrary fields. Again, the author keeps the treatment of prerequisites self-contained. The material of t...
Parametric Linear Dynamic Logic
Peter Faymonville
2014-08-01
Full Text Available We introduce Parametric Linear Dynamic Logic (PLDL, which extends Linear Dynamic Logic (LDL by temporal operators equipped with parameters that bound their scope. LDL was proposed as an extension of Linear Temporal Logic (LTL that is able to express all ω-regular specifications while still maintaining many of LTL's desirable properties like an intuitive syntax and a translation into non-deterministic Büchi automata of exponential size. But LDL lacks capabilities to express timing constraints. By adding parameterized operators to LDL, we obtain a logic that is able to express all ω-regular properties and that subsumes parameterized extensions of LTL like Parametric LTL and PROMPT-LTL. Our main technical contribution is a translation of PLDL formulas into non-deterministic Büchi word automata of exponential size via alternating automata. This yields a PSPACE model checking algorithm and a realizability algorithm with doubly-exponential running time. Furthermore, we give tight upper and lower bounds on optimal parameter values for both problems. These results show that PLDL model checking and realizability are not harder than LTL model checking and realizability.
Quantum linear Boltzmann equation
Vacchini, Bassano; Hornberger, Klaus
2009-01-01
We review the quantum version of the linear Boltzmann equation, which describes in a non-perturbative fashion, by means of scattering theory, how the quantum motion of a single test particle is affected by collisions with an ideal background gas. A heuristic derivation of this Lindblad master equation is presented, based on the requirement of translation-covariance and on the relation to the classical linear Boltzmann equation. After analyzing its general symmetry properties and the associated relaxation dynamics, we discuss a quantum Monte Carlo method for its numerical solution. We then review important limiting forms of the quantum linear Boltzmann equation, such as the case of quantum Brownian motion and pure collisional decoherence, as well as the application to matter wave optics. Finally, we point to the incorporation of quantum degeneracies and self-interactions in the gas by relating the equation to the dynamic structure factor of the ambient medium, and we provide an extension of the equation to include internal degrees of freedom.
Emma, P.
1995-01-01
The Stanford Linear Collider (SLC) is the first and only high-energy e + e - linear collider in the world. Its most remarkable features are high intensity, submicron sized, polarized (e - ) beams at a single interaction point. The main challenges posed by these unique characteristics include machine-wide emittance preservation, consistent high intensity operation, polarized electron production and transport, and the achievement of a high degree of beam stability on all time scales. In addition to serving as an important machine for the study of Z 0 boson production and decay using polarized beams, the SLC is also an indispensable source of hands-on experience for future linear colliders. Each new year of operation has been highlighted with a marked improvement in performance. The most significant improvements for the 1994-95 run include new low impedance vacuum chambers for the damping rings, an upgrade to the optics and diagnostics of the final focus systems, and a higher degree of polarization from the electron source. As a result, the average luminosity has nearly doubled over the previous year with peaks approaching 10 30 cm -2 s -1 and an 80% electron polarization at the interaction point. These developments as well as the remaining identifiable performance limitations will be discussed
Members of the LHC Resources Review Boards
Maximilien Brice
2002-01-01
Photo 01: Members of the LHCRRB visiting Point 2, hosting the ALICE experiment From l. to r. : W. Korda, Head of the VIP Office; P. Rimmer, CERN public relations, J. Seed, Member of the LHCRRB, J.-P. Revol, ALICE CERN Team Leader; J. Bartke, Member of the LHCRRB; F. Suransky, Member of the LHCRRB; J. Schukraft, Spokesperson, ALICE experiment and S. Molinari, VIP Office. Photo 02: Members of the LHC Resources Review Boards visiting the ALICE magnet at Point 2. L. to. r.: O. Dines-Hansen, H. Boggild, S. Irgens-Jensens, H.A. Gustafsson Photo 03: Members of the LHCRRB visiting Point 2, hosting the ALICE experiment From l. t to r.: J.Richter, Member of the LHCRRB; H. Gutbrod, Deputy Spokesperson, ALICE experiment; G. Paic, ALICE experiment; D. Muller, Member of the LHCRRB; P. Brau-Munzinger, ALICE experiment; R. Santo, Member of the LHCRRB, A. Van Rijn, Member of the LHCRRB; J. Engelen, Member of the LHCRRB.
Tension stiffening in partially prestressed concrete flexural members
Oukaili, K. N.
2000-01-01
Concrete tensile strength is not being zero, cracking does not extend to the neutral axis as assumed in standard cracked section analysis. In addition, un cracked concrete, which exists above the crack tip in the tension zone, contributes to the stiffness of the member. This paper discusses the influence of concrete tensile stress below the neut ural axis position at the cracked section on the tension stiffening phenomenon and deflection of progressively cracking partially prestressed concrete flexural members. The computation of the neutral axis location, which takes into consideration the effect of concrete in tension, can be achieved by solving iteratively tow simultaneous equation derived from forces and moments equilibrium, strain compatibility and linear stress - strain relationship in concrete across the section depth. Once the section depth after cracking is known, it can be used to calculate the effective moment of inertia for deflection analysis. (author). 13 refs., 3 figs., 1 table
Garbet, X.; Mourgues, F.; Samain, A.
1987-01-01
Among the various instabilities which could explain the anomalous electron heat transport observed in tokamaks during additional heating, a microtearing turbulence is a reasonable candidate since it affects directly the magnetic topology. This turbulence may be described in a proper frame rotating around the majors axis by a static potential vector. In strong non linear regimes, the flow of electrons along the stochastic field lines induces a current. The point is to know whether this current can sustain the turbulence. The mechanisms of this self-consistency, involving the combined effects of the thermal diamagnetism and of the electric drift are presented here
Wangler, Thomas P
2008-01-01
Thomas P. Wangler received his B.S. degree in physics from Michigan State University, and his Ph.D. degree in physics and astronomy from the University of Wisconsin. After postdoctoral appointments at the University of Wisconsin and Brookhaven National Laboratory, he joined the staff of Argonne National Laboratory in 1966, working in the fields of experimental high-energy physics and accelerator physics. He joined the Accelerator Technology Division at Los Alamos National Laboratory in 1979, where he specialized in high-current beam physics and linear accelerator design and technology. In 2007
Richter, B.; Bell, R.A.; Brown, K.L.
1980-06-01
The SLAC LINEAR COLLIDER is designed to achieve an energy of 100 GeV in the electron-positron center-of-mass system by accelerating intense bunches of particles in the SLAC linac and transporting the electron and positron bunches in a special magnet system to a point where they are focused to a radius of about 2 microns and made to collide head on. The rationale for this new type of colliding beam system is discussed, the project is described, some of the novel accelerator physics issues involved are discussed, and some of the critical technical components are described
Lopez, Cesar
2014-01-01
MATLAB is a high-level language and environment for numerical computation, visualization, and programming. Using MATLAB, you can analyze data, develop algorithms, and create models and applications. The language, tools, and built-in math functions enable you to explore multiple approaches and reach a solution faster than with spreadsheets or traditional programming languages, such as C/C++ or Java. MATLAB Linear Algebra introduces you to the MATLAB language with practical hands-on instructions and results, allowing you to quickly achieve your goals. In addition to giving an introduction to
Special set linear algebra and special set fuzzy linear algebra
Kandasamy, W. B. Vasantha; Smarandache, Florentin; Ilanthenral, K.
2009-01-01
The authors in this book introduce the notion of special set linear algebra and special set fuzzy Linear algebra, which is an extension of the notion set linear algebra and set fuzzy linear algebra. These concepts are best suited in the application of multi expert models and cryptology. This book has five chapters. In chapter one the basic concepts about set linear algebra is given in order to make this book a self contained one. The notion of special set linear algebra and their fuzzy analog...
Munehiro, H
1980-05-29
When driving the carriage of a printer through a rotating motor, there are problems regarding the limited accuracy of the carriage position due to rotation or contraction and ageing of the cable. In order to solve the problem, a direct drive system was proposed, in which the printer carriage is driven by a linear motor. If one wants to keep the motor circuit of such a motor compact, then the magnetic flux density in the air gap must be reduced or the motor travel must be reduced. It is the purpose of this invention to create an electrodynamic linear motor, which on the one hand is compact and light and on the other hand has a relatively high constant force over a large travel. The invention is characterised by the fact that magnetic fields of alternating polarity are generated at equal intervals in the magnetic field, and that the coil arrangement has 2 adjacent coils, whose size corresponds to half the length of each magnetic pole. A logic circuit is provided to select one of the two coils and to determine the direction of the current depending on the signals of a magnetic field sensor on the coil arrangement.
Kozarov, A.; Petrov, O.; Antonov, J.; Sotirova, S.; Petrova, B.
2006-01-01
The purpose of the linear wind-power generator described in this article is to decrease the following disadvantages of the common wind-powered turbine: 1) large bending and twisting moments to the blades and the shaft, especially when strong winds and turbulence exist; 2) significant values of the natural oscillation period of the construction result in the possibility of occurrence of destroying resonance oscillations; 3) high velocity of the peripheral parts of the rotor creating a danger for birds; 4) difficulties, connected with the installation and the operation on the mountain ridges and passages where the wind energy potential is the largest. The working surfaces of the generator in questions driven by the wind are not connected with a joint shaft but each moves along a railway track with few oscillations. So the sizes of each component are small and their number can be rather large. The mechanical trajectory is not a circle but a closed outline in a vertical plain, which consists of two rectilinear sectors, one above the other, connected in their ends by semi-circumferences. The mechanical energy of each component turns into electrical on the principle of the linear electrical generator. A regulation is provided when the direction of the wind is perpendicular to the route. A possibility of effectiveness is shown through aiming of additional quantities of air to the movable components by static barriers
Partially Flipped Linear Algebra: A Team-Based Approach
Carney, Debra; Ormes, Nicholas; Swanson, Rebecca
2015-01-01
In this article we describe a partially flipped Introductory Linear Algebra course developed by three faculty members at two different universities. We give motivation for our partially flipped design and describe our implementation in detail. Two main features of our course design are team-developed preview videos and related in-class activities.…
Linearization of the Lorenz system
Li, Chunbiao; Sprott, Julien Clinton; Thio, Wesley
2015-01-01
A partial and complete piecewise linearized version of the Lorenz system is proposed. The linearized versions have an independent total amplitude control parameter. Additional further linearization leads naturally to a piecewise linear version of the diffusionless Lorenz system. A chaotic circuit with a single amplitude controller is then implemented using a new switch element, producing a chaotic oscillation that agrees with the numerical calculation for the piecewise linear diffusionless Lorenz system. - Highlights: • A partial and complete piecewise linearized version of the Lorenz system are addressed. • The linearized versions have an independent total amplitude control parameter. • A piecewise linear version of the diffusionless Lorenz system is derived by further linearization. • A corresponding chaotic circuit without any multiplier is implemented for the chaotic oscillation
Topics in computational linear optimization
Hultberg, Tim Helge
2000-01-01
Linear optimization has been an active area of research ever since the pioneering work of G. Dantzig more than 50 years ago. This research has produced a long sequence of practical as well as theoretical improvements of the solution techniques avilable for solving linear optimization problems...... of high quality solvers and the use of algebraic modelling systems to handle the communication between the modeller and the solver. This dissertation features four topics in computational linear optimization: A) automatic reformulation of mixed 0/1 linear programs, B) direct solution of sparse unsymmetric...... systems of linear equations, C) reduction of linear programs and D) integration of algebraic modelling of linear optimization problems in C++. Each of these topics is treated in a separate paper included in this dissertation. The efficiency of solving mixed 0-1 linear programs by linear programming based...
Linearization of the Lorenz system
Li, Chunbiao, E-mail: goontry@126.com [School of Electronic & Information Engineering, Nanjing University of Information Science & Technology, Nanjing 210044 (China); Engineering Technology Research and Development Center of Jiangsu Circulation Modernization Sensor Network, Jiangsu Institute of Commerce, Nanjing 211168 (China); Sprott, Julien Clinton [Department of Physics, University of Wisconsin–Madison, Madison, WI 53706 (United States); Thio, Wesley [Department of Electrical and Computer Engineering, The Ohio State University, Columbus, OH 43210 (United States)
2015-05-08
A partial and complete piecewise linearized version of the Lorenz system is proposed. The linearized versions have an independent total amplitude control parameter. Additional further linearization leads naturally to a piecewise linear version of the diffusionless Lorenz system. A chaotic circuit with a single amplitude controller is then implemented using a new switch element, producing a chaotic oscillation that agrees with the numerical calculation for the piecewise linear diffusionless Lorenz system. - Highlights: • A partial and complete piecewise linearized version of the Lorenz system are addressed. • The linearized versions have an independent total amplitude control parameter. • A piecewise linear version of the diffusionless Lorenz system is derived by further linearization. • A corresponding chaotic circuit without any multiplier is implemented for the chaotic oscillation.
Fracture mechanical analysis of strengthened concrete tension members with one crack
Hansen, Christian Skodborg; Stang, Henrik
2012-01-01
A concrete tension member strengthened 2 with fiber reinforced polymer plates on two sides 3 is analyzed with non-linear fracture mechanics. The 4 analysis of the strengthened tension member incorpo5 rates cohesive properties for both concrete and inter6 face between concrete and strengthening...... the structural classification parameters, is inves13 tigated in a non-dimensional analysis, and found to 14 depend strongly on the ratio between interfacial and 15 concrete fracture energies....
Finding Street Gang Members on Twitter
Balasuriya, Lakshika; Wijeratne, Sanjaya; Doran, Derek; Sheth, Amit
2016-01-01
Most street gang members use Twitter to intimidate others, to present outrageous images and statements to the world, and to share recent illegal activities. Their tweets may thus be useful to law enforcement agencies to discover clues about recent crimes or to anticipate ones that may occur. Finding these posts, however, requires a method to discover gang member Twitter profiles. This is a challenging task since gang members represent a very small population of the 320 million Twitter users. ...
On the linear programming bound for linear Lee codes.
Astola, Helena; Tabus, Ioan
2016-01-01
Based on an invariance-type property of the Lee-compositions of a linear Lee code, additional equality constraints can be introduced to the linear programming problem of linear Lee codes. In this paper, we formulate this property in terms of an action of the multiplicative group of the field [Formula: see text] on the set of Lee-compositions. We show some useful properties of certain sums of Lee-numbers, which are the eigenvalues of the Lee association scheme, appearing in the linear programming problem of linear Lee codes. Using the additional equality constraints, we formulate the linear programming problem of linear Lee codes in a very compact form, leading to a fast execution, which allows to efficiently compute the bounds for large parameter values of the linear codes.
Post-processing through linear regression
van Schaeybroeck, B.; Vannitsem, S.
2011-03-01
Various post-processing techniques are compared for both deterministic and ensemble forecasts, all based on linear regression between forecast data and observations. In order to evaluate the quality of the regression methods, three criteria are proposed, related to the effective correction of forecast error, the optimal variability of the corrected forecast and multicollinearity. The regression schemes under consideration include the ordinary least-square (OLS) method, a new time-dependent Tikhonov regularization (TDTR) method, the total least-square method, a new geometric-mean regression (GM), a recently introduced error-in-variables (EVMOS) method and, finally, a "best member" OLS method. The advantages and drawbacks of each method are clarified. These techniques are applied in the context of the 63 Lorenz system, whose model version is affected by both initial condition and model errors. For short forecast lead times, the number and choice of predictors plays an important role. Contrarily to the other techniques, GM degrades when the number of predictors increases. At intermediate lead times, linear regression is unable to provide corrections to the forecast and can sometimes degrade the performance (GM and the best member OLS with noise). At long lead times the regression schemes (EVMOS, TDTR) which yield the correct variability and the largest correlation between ensemble error and spread, should be preferred.
Post-processing through linear regression
B. Van Schaeybroeck
2011-03-01
Full Text Available Various post-processing techniques are compared for both deterministic and ensemble forecasts, all based on linear regression between forecast data and observations. In order to evaluate the quality of the regression methods, three criteria are proposed, related to the effective correction of forecast error, the optimal variability of the corrected forecast and multicollinearity. The regression schemes under consideration include the ordinary least-square (OLS method, a new time-dependent Tikhonov regularization (TDTR method, the total least-square method, a new geometric-mean regression (GM, a recently introduced error-in-variables (EVMOS method and, finally, a "best member" OLS method. The advantages and drawbacks of each method are clarified.
These techniques are applied in the context of the 63 Lorenz system, whose model version is affected by both initial condition and model errors. For short forecast lead times, the number and choice of predictors plays an important role. Contrarily to the other techniques, GM degrades when the number of predictors increases. At intermediate lead times, linear regression is unable to provide corrections to the forecast and can sometimes degrade the performance (GM and the best member OLS with noise. At long lead times the regression schemes (EVMOS, TDTR which yield the correct variability and the largest correlation between ensemble error and spread, should be preferred.
Introduction to linear elasticity
Gould, Phillip L
2013-01-01
Introduction to Linear Elasticity, 3rd Edition, provides an applications-oriented grounding in the tensor-based theory of elasticity for students in mechanical, civil, aeronautical, and biomedical engineering, as well as materials and earth science. The book is distinct from the traditional text aimed at graduate students in solid mechanics by introducing the subject at a level appropriate for advanced undergraduate and beginning graduate students. The author's presentation allows students to apply the basic notions of stress analysis and move on to advanced work in continuum mechanics, plasticity, plate and shell theory, composite materials, viscoelasticity and finite method analysis. This book also: Emphasizes tensor-based approach while still distilling down to explicit notation Provides introduction to theory of plates, theory of shells, wave propagation, viscoelasticity and plasticity accessible to advanced undergraduate students Appropriate for courses following emerging trend of teaching solid mechan...
Haniger, L.; Elger, R.; Kocandrle, L.; Zdebor, J.
1986-01-01
A linear step drive is described developed in Czechoslovak-Soviet cooperation and intended for driving WWER-1000 control rods. The functional principle is explained of the motor and the mechanical and electrical parts of the drive, power control, and the indicator of position are described. The motor has latches situated in the reactor at a distance of 3 m from magnetic armatures, it has a low structural height above the reactor cover, which suggests its suitability for seismic localities. Its magnetic circuits use counterpoles; the mechanical shocks at the completion of each step are damped using special design features. The position indicator is of a special design and evaluates motor position within ±1% of total travel. A drive diagram and the flow chart of both the control electronics and the position indicator are presented. (author) 4 figs
Tjutju, R.L.
1977-01-01
Pulse amplifier is standard significant part of spectrometer. Apart from other type of amplification, it's a combination of amplification and pulse shaping. Because of its special purpose the device should fulfill the following : High resolution is desired to gain a high yield comparable to its actual state of condition. High signal to noise is desired to nhν resolution. High linearity to facilitate calibration. A good overload recovery, in order to the device will capable of analizing a low energy radiation which appear joinly on the high energy fields. Other expections of the device are its economical and practical use its extentive application. For that reason it's built on a standard NIM principle. Taking also into account the above mentioned considerations. High quality component parts are used throughout, while its availability in the domestic market is secured. (author)
1976-01-01
This report covers the activity of the Linear Accelerator Laboratory during the period June 1974-June 1976. The activity of the Laboratory is essentially centered on high energy physics. The main activities were: experiments performed with the colliding rings (ACO), construction of the new colliding rings and beginning of the work at higher energy (DCI), bubble chamber experiments with the CERN PS neutrino beam, counter experiments with CERN's PS and setting-up of equipment for new experiments with CERN's SPS. During this period a project has also been prepared for an experiment with the new PETRA colliding ring at Hamburg. On the other hand, intense collaboration with the LURE Laboratory, using the electron synchrotron radiation emitted by ACO and DCI, has been developed [fr
Van Atta, C.M.; Beringer, R.; Smith, L.
1959-01-01
A linear accelerator of heavy ions is described. The basic contributions of the invention consist of a method and apparatus for obtaining high energy particles of an element with an increased charge-to-mass ratio. The method comprises the steps of ionizing the atoms of an element, accelerating the resultant ions to an energy substantially equal to one Mev per nucleon, stripping orbital electrons from the accelerated ions by passing the ions through a curtain of elemental vapor disposed transversely of the path of the ions to provide a second charge-to-mass ratio, and finally accelerating the resultant stripped ions to a final energy of at least ten Mev per nucleon.
Tip, A.
1998-06-01
Starting from Maxwell's equations for a linear, nonconducting, absorptive, and dispersive medium, characterized by the constitutive equations D(x,t)=ɛ1(x)E(x,t)+∫t-∞dsχ(x,t-s)E(x,s) and H(x,t)=B(x,t), a unitary time evolution and canonical formalism is obtained. Given the complex, coordinate, and frequency-dependent, electric permeability ɛ(x,ω), no further assumptions are made. The procedure leads to a proper definition of band gaps in the periodic case and a new continuity equation for energy flow. An S-matrix formalism for scattering from lossy objects is presented in full detail. A quantized version of the formalism is derived and applied to the generation of Čerenkov and transition radiation as well as atomic decay. The last case suggests a useful generalization of the density of states to the absorptive situation.
Computer Program For Linear Algebra
Krogh, F. T.; Hanson, R. J.
1987-01-01
Collection of routines provided for basic vector operations. Basic Linear Algebra Subprogram (BLAS) library is collection from FORTRAN-callable routines for employing standard techniques to perform basic operations of numerical linear algebra.
Quaternion Linear Canonical Transform Application
Bahri, Mawardi
2015-01-01
Quaternion linear canonical transform (QLCT) is a generalization of the classical linear canonical transfom (LCT) using quaternion algebra. The focus of this paper is to introduce an application of the QLCT to study of generalized swept-frequency filter
Recursive Algorithm For Linear Regression
Varanasi, S. V.
1988-01-01
Order of model determined easily. Linear-regression algorithhm includes recursive equations for coefficients of model of increased order. Algorithm eliminates duplicative calculations, facilitates search for minimum order of linear-regression model fitting set of data satisfactory.
Dynamical systems and linear algebra
Colonius, Fritz (Prof.)
2007-01-01
Dynamical systems and linear algebra / F. Colonius, W. Kliemann. - In: Handbook of linear algebra / ed. by Leslie Hogben. - Boca Raton : Chapman & Hall/CRC, 2007. - S. 56,1-56,22. - (Discrete mathematics and its applications)
Linear spaces: history and theory
Albrecht Beutelspracher
1990-01-01
Linear spaces belong to the most fundamental geometric and combinatorial structures. In this paper I would like to give an onerview about the theory of embedding finite linear spaces in finite projective planes.
Linear versus non-linear supersymmetry, in general
Ferrara, Sergio [Theoretical Physics Department, CERN,CH-1211 Geneva 23 (Switzerland); INFN - Laboratori Nazionali di Frascati,Via Enrico Fermi 40, I-00044 Frascati (Italy); Department of Physics and Astronomy, UniversityC.L.A.,Los Angeles, CA 90095-1547 (United States); Kallosh, Renata [SITP and Department of Physics, Stanford University,Stanford, California 94305 (United States); Proeyen, Antoine Van [Institute for Theoretical Physics, Katholieke Universiteit Leuven,Celestijnenlaan 200D, B-3001 Leuven (Belgium); Wrase, Timm [Institute for Theoretical Physics, Technische Universität Wien,Wiedner Hauptstr. 8-10, A-1040 Vienna (Austria)
2016-04-12
We study superconformal and supergravity models with constrained superfields. The underlying version of such models with all unconstrained superfields and linearly realized supersymmetry is presented here, in addition to the physical multiplets there are Lagrange multiplier (LM) superfields. Once the equations of motion for the LM superfields are solved, some of the physical superfields become constrained. The linear supersymmetry of the original models becomes non-linearly realized, its exact form can be deduced from the original linear supersymmetry. Known examples of constrained superfields are shown to require the following LM’s: chiral superfields, linear superfields, general complex superfields, some of them are multiplets with a spin.
Linear versus non-linear supersymmetry, in general
Ferrara, Sergio; Kallosh, Renata; Proeyen, Antoine Van; Wrase, Timm
2016-01-01
We study superconformal and supergravity models with constrained superfields. The underlying version of such models with all unconstrained superfields and linearly realized supersymmetry is presented here, in addition to the physical multiplets there are Lagrange multiplier (LM) superfields. Once the equations of motion for the LM superfields are solved, some of the physical superfields become constrained. The linear supersymmetry of the original models becomes non-linearly realized, its exact form can be deduced from the original linear supersymmetry. Known examples of constrained superfields are shown to require the following LM’s: chiral superfields, linear superfields, general complex superfields, some of them are multiplets with a spin.
Monahan, John F
2008-01-01
Preface Examples of the General Linear Model Introduction One-Sample Problem Simple Linear Regression Multiple Regression One-Way ANOVA First Discussion The Two-Way Nested Model Two-Way Crossed Model Analysis of Covariance Autoregression Discussion The Linear Least Squares Problem The Normal Equations The Geometry of Least Squares Reparameterization Gram-Schmidt Orthonormalization Estimability and Least Squares Estimators Assumptions for the Linear Mean Model Confounding, Identifiability, and Estimability Estimability and Least Squares Estimators F
7 CFR 1425.14 - Member business.
2010-01-01
... 7 Agriculture 10 2010-01-01 2010-01-01 false Member business. 1425.14 Section 1425.14 Agriculture... business. (a) At least 50 percent of a crop of an authorized commodity acquired by, or delivered to, a CMA... not be considered in determining the volume of member or nonmember business. ...
Templates for Linear Algebra Problems
Bai, Z.; Day, D.; Demmel, J.; Dongarra, J.; Gu, M.; Ruhe, A.; Vorst, H.A. van der
1995-01-01
The increasing availability of advanced-architecture computers is having a very signicant eect on all spheres of scientic computation, including algorithm research and software development in numerical linear algebra. Linear algebra {in particular, the solution of linear systems of equations and
Linearization of CIF through SOS
Nadales Agut, D.E.; Reniers, M.A.; Luttik, B.; Valencia, F.
2011-01-01
Linearization is the procedure of rewriting a process term into a linear form, which consist only of basic operators of the process language. This procedure is interesting both from a theoretical and a practical point of view. In particular, a linearization algorithm is needed for the Compositional
Engberg, Uffe Henrik; Winskel, Glynn
This article shows how individual Petri nets form models of Girard's intuitionistic linear logic. It explores questions of expressiveness and completeness of linear logic with respect to this interpretation. An aim is to use Petri nets to give an understanding of linear logic and give some apprai...
Richards, J.A.
1977-01-01
A linear particle accelerator which provides a pulsed beam of charged particles of uniform energy is described. The accelerator is in the form of an evacuated dielectric tube, inside of which a particle source is located at one end of the tube, with a target or window located at the other end of the dielectric tube. Along the length of the tube are externally located pairs of metal plates, each insulated from each other in an insulated housing. Each of the plates of a pair are connected to an electrical source of voltage of opposed polarity, with the polarity of the voltage of the plates oriented so that the plate of a pair, nearer to the particle source, is of the opposed polarity to the charge of the particle emitted by the source. Thus, a first plate about the tube located nearest the particle source, attracts a particle which as it passes through the tube past the first plate is then repelled by the reverse polarity of the second plate of the pair to continue moving towards the target
Generalized Linear Covariance Analysis
Carpenter, James R.; Markley, F. Landis
2014-01-01
This talk presents a comprehensive approach to filter modeling for generalized covariance analysis of both batch least-squares and sequential estimators. We review and extend in two directions the results of prior work that allowed for partitioning of the state space into solve-for'' and consider'' parameters, accounted for differences between the formal values and the true values of the measurement noise, process noise, and textita priori solve-for and consider covariances, and explicitly partitioned the errors into subspaces containing only the influence of the measurement noise, process noise, and solve-for and consider covariances. In this work, we explicitly add sensitivity analysis to this prior work, and relax an implicit assumption that the batch estimator's epoch time occurs prior to the definitive span. We also apply the method to an integrated orbit and attitude problem, in which gyro and accelerometer errors, though not estimated, influence the orbit determination performance. We illustrate our results using two graphical presentations, which we call the variance sandpile'' and the sensitivity mosaic,'' and we compare the linear covariance results to confidence intervals associated with ensemble statistics from a Monte Carlo analysis.
Equipartitioning in linear accelerators
Jameson, R.A.
1982-01-01
Emittance growth has long been a concern in linear accelerators, as has the idea that some kind of energy balance, or equipartitioning, between the degrees of freedom, would ameliorate the growth. M. Prome observed that the average transverse and longitudinal velocity spreads tend to equalize as current in the channel is increased, while the sum of the energy in the system stays nearly constant. However, only recently have we shown that an equipartitioning requirement on a bunched injected beam can indeed produce remarkably small emittance growth. The simple set of equations leading to this condition are outlined. At the same time, Hofmann has investigated collective instabilities in transported beams and has identified thresholds and regions in parameter space where instabilities occur. Evidence is presented that shows transport system boundaries to be quite accurate in computer simulations of accelerating systems. Discussed are preliminary results of efforts to design accelerators that avoid parameter regions where emittance is affected by the instabilities identified by Hofmann. These efforts suggest that other mechanisms are present. The complicated behavior of the RFQ linac in this framework also is shown
Equipartitioning in linear accelerators
Jameson, R.A.
1981-01-01
Emittance growth has long been a concern in linear accelerators, as has the idea that some kind of energy balance, or equipartitioning, between the degrees of freedom, would ameliorate the growth. M. Prome observed that the average transverse and longitudinal velocity spreads tend to equalize as current in the channel is increased, while the sum of the energy in the system stays nearly constant. However, only recently have we shown that an equipartitioning requirement on a bunched injected beam can indeed produce remarkably small emittance growth. The simple set of equations leading to this condition are outlined below. At the same time, Hofmann, using powerful analytical and computational methods, has investigated collective instabilities in transported beams and has identified thresholds and regions in parameter space where instabilities occur. This is an important generalization. Work that he will present at this conference shows that the results are essentially the same in r-z coordinates for transport systems, and evidence is presented that shows transport system boundaries to be quite accurate in computer simulations of accelerating systems also. Discussed are preliminary results of efforts to design accelerators that avoid parameter regions where emittance is affected by the instabilities identified by Hofmann. These efforts suggest that other mechanisms are present. The complicated behavior of the RFQ linac in this framework also is shown
Briggs, R.J.
1986-06-01
The development of linear induction accelerators has been motivated by applications requiring high-pulsed currents of charged particles at voltages exceeding the capability of single-stage, diode-type accelerators and at currents too high for rf accelerators. In principle, one can accelerate charged particles to arbitrarily high voltages using a multi-stage induction machine, but the 50-MeV, 10-kA Advanced Test Accelerator (ATA) at LLNL is the highest voltage machine in existence at this time. The advent of magnetic pulse power systems makes sustained operation at high-repetition rates practical, and this capability for high-average power is very likely to open up many new applications of induction machines in the future. This paper surveys the US induction linac technology with primary emphasis on electron machines. A simplified description of how induction machines couple energy to the electron beam is given, to illustrate many of the general issues that bound the design space of induction linacs
Berkeley Proton Linear Accelerator
Alvarez, L. W.; Bradner, H.; Franck, J.; Gordon, H.; Gow, J. D.; Marshall, L. C.; Oppenheimer, F. F.; Panofsky, W. K. H.; Richman, C.; Woodyard, J. R.
1953-10-13
A linear accelerator, which increases the energy of protons from a 4 Mev Van de Graaff injector, to a final energy of 31.5 Mev, has been constructed. The accelerator consists of a cavity 40 feet long and 39 inches in diameter, excited at resonance in a longitudinal electric mode with a radio-frequency power of about 2.2 x 10{sup 6} watts peak at 202.5 mc. Acceleration is made possible by the introduction of 46 axial "drift tubes" into the cavity, which is designed such that the particles traverse the distance between the centers of successive tubes in one cycle of the r.f. power. The protons are longitudinally stable as in the synchrotron, and are stabilized transversely by the action of converging fields produced by focusing grids. The electrical cavity is constructed like an inverted airplane fuselage and is supported in a vacuum tank. Power is supplied by 9 high powered oscillators fed from a pulse generator of the artificial transmission line type.
Random linear codes in steganography
Kamil Kaczyński
2016-12-01
Full Text Available Syndrome coding using linear codes is a technique that allows improvement in the steganographic algorithms parameters. The use of random linear codes gives a great flexibility in choosing the parameters of the linear code. In parallel, it offers easy generation of parity check matrix. In this paper, the modification of LSB algorithm is presented. A random linear code [8, 2] was used as a base for algorithm modification. The implementation of the proposed algorithm, along with practical evaluation of algorithms’ parameters based on the test images was made.[b]Keywords:[/b] steganography, random linear codes, RLC, LSB
Linear Algebraic Method for Non-Linear Map Analysis
Yu, L.; Nash, B.
2009-01-01
We present a newly developed method to analyze some non-linear dynamics problems such as the Henon map using a matrix analysis method from linear algebra. Choosing the Henon map as an example, we analyze the spectral structure, the tune-amplitude dependence, the variation of tune and amplitude during the particle motion, etc., using the method of Jordan decomposition which is widely used in conventional linear algebra.
Concerns raised over new EPA members
Gwynne, Peter
2017-12-01
The Trump administration has nominated three new members of the Environmental Protection Agency (EPA) who critics say are undermining laws and “pampering” the industries they are supposed to regulate.
Energy outlooks of young members of parliament
Tolonen, P.
1999-01-01
Pekka Tolonen Energy outlooks of young members of parliament The main theme is 'youth and nuclear energy'. This article presents opinions of young opinion leaders over energy policy and nuclear energy
Member states buoy up beleagured EMBL
Balter, M
1999-01-01
EMBL's governing council, made up of delegates from the lab's 16 member countries, agreed in principle to meet the costs of a multimillion-dollar pay claim, the result of a recent ruling by the ILO in Geneva (1 page).
Israel, CERN’s new Member State
Brice, Maximilien
2014-01-01
On Wednesday, 15 January 2014, the official Israeli Flag-raising Ceremony took place to mark the accession of Israel to Membership of CERN, bringing the Organization’s number of Member States to 21.
Team Members | Center for Cancer Research
Our Team Members The Foregut Team includes experts in the diagnosis and treatment of the diseases listed below. Our clinical experience and active research offers patients the highest quality care in the setting of groundbreaking clinical trials.
STRUCTURAL PERFORMANCE OF DEGRADED REINFORCED CONCRETE MEMBERS
Braverman, J.I.; Miller, C.A.; Ellingwood, B.R.; Naus, D.J.; Hofmayer, C.H.; Bezler, P.; Chang, T.Y.
2001-01-01
This paper describes the results of a study to evaluate, in probabilistic terms, the effects of age-related degradation on the structural performance of reinforced concrete members at nuclear power plants. The paper focuses on degradation of reinforced concrete flexural members and shear walls due to the loss of steel reinforcing area and loss of concrete area (cracking/spalling). Loss of steel area is typically caused by corrosion while cracking and spalling can be caused by corrosion of reinforcing steel, freeze-thaw, or aggressive chemical attack. Structural performance in the presence of uncertainties is depicted by a fragility (or conditional probability of failure). The effects of degradation on the fragility of reinforced concrete members are calculated to assess the potential significance of various levels of degradation. The fragility modeling procedures applied to degraded concrete members can be used to assess the effects of degradation on plant risk and can lead to the development of probability-based degradation acceptance limits
On some properties of the block linear multi-step methods | Chollom ...
The convergence, stability and order of Block linear Multistep methods have been determined in the past based on individual members of the block. In this paper, methods are proposed to examine the properties of the entire block. Some Block Linear Multistep methods have been considered, their convergence, stability and ...
Linear Programming and Network Flows
Bazaraa, Mokhtar S; Sherali, Hanif D
2011-01-01
The authoritative guide to modeling and solving complex problems with linear programming-extensively revised, expanded, and updated The only book to treat both linear programming techniques and network flows under one cover, Linear Programming and Network Flows, Fourth Edition has been completely updated with the latest developments on the topic. This new edition continues to successfully emphasize modeling concepts, the design and analysis of algorithms, and implementation strategies for problems in a variety of fields, including industrial engineering, management science, operations research
LINEAR2007, Linear-Linear Interpolation of ENDF Format Cross-Sections
2007-01-01
1 - Description of program or function: LINEAR converts evaluated cross sections in the ENDF/B format into a tabular form that is subject to linear-linear interpolation in energy and cross section. The code also thins tables of cross sections already in that form. Codes used subsequently need thus to consider only linear-linear data. IAEA1311/15: This version include the updates up to January 30, 2007. Changes in ENDF/B-VII Format and procedures, as well as the evaluations themselves, make it impossible for versions of the ENDF/B pre-processing codes earlier than PREPRO 2007 (2007 Version) to accurately process current ENDF/B-VII evaluations. The present code can handle all existing ENDF/B-VI evaluations through release 8, which will be the last release of ENDF/B-VI. Modifications from previous versions: - Linear VERS. 2007-1 (JAN. 2007): checked against all ENDF/B-VII; increased page size from 60,000 to 600,000 points 2 - Method of solution: Each section of data is considered separately. Each section of File 3, 23, and 27 data consists of a table of cross section versus energy with any of five interpolation laws. LINEAR will replace each section with a new table of energy versus cross section data in which the interpolation law is always linear in energy and cross section. The histogram (constant cross section between two energies) interpolation law is converted to linear-linear by substituting two points for each initial point. The linear-linear is not altered. For the log-linear, linear-log and log- log laws, the cross section data are converted to linear by an interval halving algorithm. Each interval is divided in half until the value at the middle of the interval can be approximated by linear-linear interpolation to within a given accuracy. The LINEAR program uses a multipoint fractional error thinning algorithm to minimize the size of each cross section table
Elementary linear programming with applications
Kolman, Bernard
1995-01-01
Linear programming finds the least expensive way to meet given needs with available resources. Its results are used in every area of engineering and commerce: agriculture, oil refining, banking, and air transport. Authors Kolman and Beck present the basic notions of linear programming and illustrate how they are used to solve important common problems. The software on the included disk leads students step-by-step through the calculations. The Second Edition is completely revised and provides additional review material on linear algebra as well as complete coverage of elementary linear program
Hood, John Linsley
2013-01-01
The Art of Linear Electronics presents the principal aspects of linear electronics and techniques in linear electronic circuit design. The book provides a wide range of information on the elucidation of the methods and techniques in the design of linear electronic circuits. The text discusses such topics as electronic component symbols and circuit drawing; passive and active semiconductor components; DC and low frequency amplifiers; and the basic effects of feedback. Subjects on frequency response modifying circuits and filters; audio amplifiers; low frequency oscillators and waveform generato
Linearity and Non-linearity of Photorefractive effect in Materials ...
Linearity and Non-linearity of Photorefractive effect in Materials using the Band transport ... For low light beam intensities the change in the refractive index is ... field is spatially phase shifted by /2 relative to the interference fringe pattern, which ...
The linear programming bound for binary linear codes
Brouwer, A.E.
1993-01-01
Combining Delsarte's (1973) linear programming bound with the information that certain weights cannot occur, new upper bounds for dmin (n,k), the maximum possible minimum distance of a binary linear code with given word length n and dimension k, are derived.
Linear operator inequalities for strongly stable weakly regular linear systems
Curtain, RF
2001-01-01
We consider the question of the existence of solutions to certain linear operator inequalities (Lur'e equations) for strongly stable, weakly regular linear systems with generating operators A, B, C, 0. These operator inequalities are related to the spectral factorization of an associated Popov
Linear and non-linear optics of condensed matter
McLean, T.P.
1977-01-01
Part I - Linear optics: 1. General introduction. 2. Frequency dependence of epsilon(ω, k vector). 3. Wave-vector dependence of epsilon(ω, k vector). 4. Tensor character of epsilon(ω, k vector). Part II - Non-linear optics: 5. Introduction. 6. A classical theory of non-linear response in one dimension. 7. The generalization to three dimensions. 8. General properties of the polarizability tensors. 9. The phase-matching condition. 10. Propagation in a non-linear dielectric. 11. Second harmonic generation. 12. Coupling of three waves. 13. Materials and their non-linearities. 14. Processes involving energy exchange with the medium. 15. Two-photon absorption. 16. Stimulated Raman effect. 17. Electro-optic effects. 18. Limitations of the approach presented here. (author)
Advanced statistics: linear regression, part I: simple linear regression.
Marill, Keith A
2004-01-01
Simple linear regression is a mathematical technique used to model the relationship between a single independent predictor variable and a single dependent outcome variable. In this, the first of a two-part series exploring concepts in linear regression analysis, the four fundamental assumptions and the mechanics of simple linear regression are reviewed. The most common technique used to derive the regression line, the method of least squares, is described. The reader will be acquainted with other important concepts in simple linear regression, including: variable transformations, dummy variables, relationship to inference testing, and leverage. Simplified clinical examples with small datasets and graphic models are used to illustrate the points. This will provide a foundation for the second article in this series: a discussion of multiple linear regression, in which there are multiple predictor variables.
ADA members weigh in on critical issues.
Burgess, Karen; Ruesch, Jon D; Mikkelsen, Matthew C; Wagner, Karen Schaid
2003-01-01
Science, new technology, patient care, dental reimbursement and government regulations all affect today's dental practitioners. To find out more about how such challenges may affect current private practitioners, the American Dental Association conducted the 2000 Membership Needs and Opinions Survey. A questionnaire was sent to 6,310 ADA members in January 2000 with follow-up mailings in February, March and April 2000. Data collection was completed in July 2000. The survey included questions on critical professional issues, and on perceptions of the ADA and ADA priorities. A total of 3,558 completed surveys were received for an adjusted response rate of 59.5 percent. Members rated the identified issues' level of importance to them. The top three issues included "maintaining my ability to recommend the treatment option I feel is most appropriate for my patients," "receiving fair reimbursement for the dental services I provide," and "protecting myself, my staff and my patients from communicable diseases." New dentists found other items to be more significant to them compared with members overall. Although ADA members as a whole had similar views on critical issues facing dentistry and ADA priorities, there were significant differences regarding some issues. New dentists were far more concerned about securing funds for their practice and paying off debt than were all ADA members. Minority dentists expressed greater levels of concern about certain issues than did all ADA members. When planning and implementing ADA activities, the Association should continue to take into account members' relative rankings of professional issues and note issues of special interest to selected membership subgroups.
Relevance of Linear Stability Results to Enhanced Oil Recovery
Ding, Xueru; Daripa, Prabir
2012-11-01
How relevant can the results based on linear stability theory for any problem for that matter be to full scale simulation results? Put it differently, is the optimal design of a system based on linear stability results is optimal or even near optimal for the complex nonlinear system with certain objectives of interest in mind? We will address these issues in the context of enhanced oil recovery by chemical flooding. This will be based on an ongoing work. Supported by Qatar National Research Fund (a member of the Qatar Foundation).
Energy recuperation in fully electric vehicles subject to stability and drivability requirements
Ólafsdóttir, J.M.; Lidberg, M.; Falcone, P.; Iersel, S. van; Jansen, S.T.H.
2012-01-01
This paper presents a combined control and estimation framework for energy recuperation in fully electric vehicles. We consider a fully electric powertrain, with a driven front axle operating on low friction road surfaces. Our objective is to find the blending of regenerative and friction braking
Supporting drivable region detection by minimising salient pixels generated through robot sensors
Falola, O
2010-11-01
Full Text Available The role of robots, automatically guided machines able to perform tasks on their own cannot be over emphasized. In particular, if robotic vehicles are to work effectively, the way they are required to perform their jobs and their ability to reach...
INFLUENCE OF DOMAIN SHIFT FACTORS ON DEEP SEGMENTATION OF THE DRIVABLE PATH OF AN AUTONOMOUS VEHICLE
R. P. A. Bormans
2018-05-01
Full Text Available One of the biggest challenges for an autonomous vehicle (and hence the WEpod is to see the world as humans would see it. This understanding is the base for a successful and reliable future of autonomous vehicles. Real-world data and semantic segmentation generally are used to achieve full understanding of its surroundings. However, deploying a pretrained segmentation network to a new, previously unseen domain will not attain similar performance as it would on the domain where it is trained on due to the differences between the domains. Although research is done concerning the mitigation of this domain shift, the factors that cause these differences are not yet fully explored. We filled this gap with the investigation of several factors. A base network was created by a two-step finetuning procedure on a convolutional neural network (SegNet which is pretrained on CityScapes (a dataset for semantic segmentation. The first tuning step is based on RobotCar (road scenery dataset recorded in Oxford, UK while afterwards this network is fine-tuned for a second time but now on the KITTI (road scenery dataset recorded in Germany dataset. With this base, experiments are used to obtain the importance of factors such as horizon line, colour and training order for a successful domain adaptation. In this case the domain adaptation is from the KITTI and RobotCar domain to the WEpod domain. For evaluation, groundtruth labels are created in a weakly-supervised setting. Negative influence was obtained for training on greyscale images instead of RGB images. This resulted in drops of IoU values up to 23.9 % for WEpod test images. The training order is a main contributor for domain adaptation with an increase in IoU of 4.7 %. This shows that the target domain (WEpod is more closely related to RobotCar than to KITTI.
Osunmakinde, IO
2009-11-01
Full Text Available of hidden paths embedded in the complex environments. Experimental evaluations of the ESA on real life and publicly available road frames outperform the classical statistical baseline methods in handling uncertainties over time. Our awareness results reveal...
Crasmareanu Mircea
2017-12-01
Full Text Available We consider the paracomplex version of the notion of mixed linear spaces introduced by M. Jurchescu in [4] by replacing the complex unit i with the paracomplex unit j, j2 = 1. The linear algebra of these spaces is studied with a special view towards their morphisms.
Linear Algebra and Image Processing
Allali, Mohamed
2010-01-01
We use the computing technology digital image processing (DIP) to enhance the teaching of linear algebra so as to make the course more visual and interesting. Certainly, this visual approach by using technology to link linear algebra to DIP is interesting and unexpected to both students as well as many faculty. (Contains 2 tables and 11 figures.)
Efficient Searching with Linear Constraints
Agarwal, Pankaj K.; Arge, Lars Allan; Erickson, Jeff
2000-01-01
We show how to preprocess a set S of points in d into an external memory data structure that efficiently supports linear-constraint queries. Each query is in the form of a linear constraint xd a0+∑d−1i=1 aixi; the data structure must report all the points of S that satisfy the constraint. This pr...
Johnson, Bruce G.; Gerver, Michael J.; Hawkey, Timothy J.; Fenn, Ralph C.
1993-01-01
Improved linear actuator comprises air slide and linear electric motor. Unit exhibits low friction, low backlash, and more nearly even acceleration. Used in machinery in which positions, velocities, and accelerations must be carefully controlled and/or vibrations must be suppressed.
Linear morphoea follows Blaschko's lines.
Weibel, L; Harper, J I
2008-07-01
The aetiology of morphoea (or localized scleroderma) remains unknown. It has previously been suggested that lesions of linear morphoea may follow Blaschko's lines and thus reflect an embryological development. However, the distribution of linear morphoea has never been accurately evaluated. We aimed to identify common patterns of clinical presentation in children with linear morphoea and to establish whether linear morphoea follows the lines of Blaschko. A retrospective chart review of 65 children with linear morphoea was performed. According to clinical photographs the skin lesions of these patients were plotted on to standardized head and body charts. With the aid of Adobe Illustrator a final figure was produced including an overlay of all individual lesions which was used for comparison with the published lines of Blaschko. Thirty-four (53%) patients had the en coup de sabre subtype, 27 (41%) presented with linear morphoea on the trunk and/or limbs and four (6%) children had a combination of the two. In 55 (85%) children the skin lesions were confined to one side of the body, showing no preference for either left or right side. On comparing the overlays of all body and head lesions with the original lines of Blaschko there was an excellent correlation. Our data indicate that linear morphoea follows the lines of Blaschko. We hypothesize that in patients with linear morphoea susceptible cells are present in a mosaic state and that exposure to some trigger factor may result in the development of this condition.
Campagnoli, Patrizia; Petris, Giovanni
2009-01-01
State space models have gained tremendous popularity in as disparate fields as engineering, economics, genetics and ecology. Introducing general state space models, this book focuses on dynamic linear models, emphasizing their Bayesian analysis. It illustrates the fundamental steps needed to use dynamic linear models in practice, using R package.
Linear Programming across the Curriculum
Yoder, S. Elizabeth; Kurz, M. Elizabeth
2015-01-01
Linear programming (LP) is taught in different departments across college campuses with engineering and management curricula. Modeling an LP problem is taught in every linear programming class. As faculty teaching in Engineering and Management departments, the depth to which teachers should expect students to master this particular type of…
Introduction to RF linear accelerators
Weiss, M.
1994-01-01
The basic features of RF linear accelerators are described. The concept of the 'loaded cavity', essential for the synchronism wave-particle, is introduced, and formulae describing the action of electromagnetic fields on the beam are given. The treatment of intense beams is mentioned, and various existing linear accelerators are presented as examples. (orig.)
Spatial Processes in Linear Ordering
von Hecker, Ulrich; Klauer, Karl Christoph; Wolf, Lukas; Fazilat-Pour, Masoud
2016-01-01
Memory performance in linear order reasoning tasks (A > B, B > C, C > D, etc.) shows quicker, and more accurate responses to queries on wider (AD) than narrower (AB) pairs on a hypothetical linear mental model (A -- B -- C -- D). While indicative of an analogue representation, research so far did not provide positive evidence for spatial…
Andersen, O. Krogh
1975-01-01
of Korringa-Kohn-Rostoker, linear-combination-of-atomic-orbitals, and cellular methods; the secular matrix is linear in energy, the overlap integrals factorize as potential parameters and structure constants, the latter are canonical in the sense that they neither depend on the energy nor the cell volume...
Migration processes in SCO member states
Valentina Sergeevna Antonyuk
2012-12-01
Full Text Available The article concerns modern state and development of migration processes in SCO member states. As a main method of research statistical analysis was applied. The article shows that migration streams between SCO member states are rather intensive, and the problem of labor migration becomes more and more urgent. The countries of consuming and supplying of labour force are clearly differentiated in the region. For some countries, labor export is the key sector of economy. At the same time, interstate relations between SCO member states sometimes are rather disputed. The most urgent factors causing the development of migration processes in the region were determined. Among them, thefactor of growing outflows from China isespecially noted. It is noted that migration processes are discussed by SCO member states nowadays in terms of illegal migration and international criminality connected with it. It means that the question of labor migration is a real problem. It is indicated that the creation of a specific joint commission on migration policy affiliated with the Council of Foreign Ministers of SCO member states is the necessary condition of effective interaction in migration questions within the framework of Shanghai Cooperation Organization.
Static Members of Classes in C#
Adrian LUPASC
2017-12-01
Full Text Available The C# language is object-oriented, which is why the declared member data must be part of a class. Thus, there is no possibility to declare certain variables that can be accessed from anywhere within the application, as it happens, for example, with global variables at the C language level. Making this work in C# is possible through static members of the class. Declaring a class implies defining some of its member data that later receive values when creating each object. A static member of the class can be interpreted as belonging only to the class, not to the objects subsequently created, which means that for the non-static data, there are as many children as there were objects created, while for the static ones there is only one copy, regardless of the number of created objects. In this regard, this paper presents the main aspects that characterize these abstract concepts of object oriented programming in general and C# language in particular, detailing how to develop an application that includes both static and non-static members. At the same time, particularities in the mirror for the two types of data, restrictions on use and potential limitations are presented.
Introduction to generalized linear models
Dobson, Annette J
2008-01-01
Introduction Background Scope Notation Distributions Related to the Normal Distribution Quadratic Forms Estimation Model Fitting Introduction Examples Some Principles of Statistical Modeling Notation and Coding for Explanatory Variables Exponential Family and Generalized Linear Models Introduction Exponential Family of Distributions Properties of Distributions in the Exponential Family Generalized Linear Models Examples Estimation Introduction Example: Failure Times for Pressure Vessels Maximum Likelihood Estimation Poisson Regression Example Inference Introduction Sampling Distribution for Score Statistics Taylor Series Approximations Sampling Distribution for MLEs Log-Likelihood Ratio Statistic Sampling Distribution for the Deviance Hypothesis Testing Normal Linear Models Introduction Basic Results Multiple Linear Regression Analysis of Variance Analysis of Covariance General Linear Models Binary Variables and Logistic Regression Probability Distributions ...
Acoustic emission linear pulse holography
Collins, H.D.; Busse, L.J.; Lemon, D.K.
1983-01-01
This paper describes the emission linear pulse holography which produces a chronological linear holographic image of a flaw by utilizing the acoustic energy emitted during crack growth. A thirty two point sampling array is used to construct phase-only linear holograms of simulated acoustic emission sources on large metal plates. The concept behind the AE linear pulse holography is illustrated, and a block diagram of a data acquisition system to implement the concept is given. Array element spacing, synthetic frequency criteria, and lateral depth resolution are specified. A reference timing transducer positioned between the array and the inspection zone and which inititates the time-of-flight measurements is described. The results graphically illustrate the technique using a one-dimensional FFT computer algorithm (ie. linear backward wave) for an AE image reconstruction
Limit analysis on FRP-strengthened RC members
D. De Domenico
2014-07-01
Full Text Available Reinforced concrete (RC members strengthened with externally bonded fiber-reinforced-polymer (FRP plates are numerically investigated by a plasticity-based limit analysis approach. The key-concept of the present approach is to adopt proper constitutive models for concrete, steel reinforcement bars (re-bars and FRP strengthening plates according to a multi-yield-criteria formulation. This allows the prediction of concrete crushing, steel bars yielding and FRP rupture that may occur at the ultimate limit state. To simulate such limitstate of the analysed elements, two iterative methods performing linear elastic analyses with adaptive elastic parameters and finite elements (FEs description are employed. The peak loads and collapse mechanisms predicted for FRP-plated RC beams are validated by comparison with the corresponding experimental findings.
Linear and Generalized Linear Mixed Models and Their Applications
Jiang, Jiming
2007-01-01
This book covers two major classes of mixed effects models, linear mixed models and generalized linear mixed models, and it presents an up-to-date account of theory and methods in analysis of these models as well as their applications in various fields. The book offers a systematic approach to inference about non-Gaussian linear mixed models. Furthermore, it has included recently developed methods, such as mixed model diagnostics, mixed model selection, and jackknife method in the context of mixed models. The book is aimed at students, researchers and other practitioners who are interested
Does formal mentoring for faculty members matter? A survey of clinical faculty members.
Mylona, Elza; Brubaker, Linda; Williams, Valerie N; Novielli, Karen D; Lyness, Jeffrey M; Pollart, Susan M; Dandar, Valerie; Bunton, Sarah A
2016-06-01
Mentoring relationships, for all medical school faculty members, are an important component of lifelong development and education, yet an understanding of mentoring among medical school clinical faculty members is incomplete. This study examined associations between formal mentoring relationships and aspects of faculty members' engagement and satisfaction. It then explored the variability of these associations across subgroups of clinical faculty members to understand the status of mentoring and outcomes of mentoring relationships. The authors hypothesised that academic clinical faculty members currently in formal mentoring relationships experience enhanced employee engagement and satisfaction with their department and institution. Medical school faculty members at 26 self-selected USA institutions participated in the 2011-2014 Faculty Forward Engagement Survey. Responses from clinical faculty members were analysed for relationships between mentoring status and perceptions of engagement by faculty members. Of the 11 953 clinical faculty respondents, almost one-third reported having a formal mentoring relationship (30%; 3529). Most mentored faculty indicated the relationship was important (86%; n = 3027), and over three-fourths were satisfied with their mentoring experience (77%; n = 2722). Mentored faculty members across ranks reported significantly higher levels of satisfaction and more positive perceptions of their roles in the organisation. Faculty members who were not receiving mentoring reported significantly less satisfaction with their workplace environment and lower overall satisfaction. Mentored clinical faculty members have significantly greater satisfaction with their department and institution. This multi-institutional study provides evidence that fostering mentoring opportunities may facilitate faculty members' satisfaction and engagement, which, in turn, may help medical schools retain high-quality faculty staff committed to the multidimensional
Cracking in Flexural Reinforced Concrete Members
Rasmussen, Annette Beedholm; Fisker, Jakob; Hagsten, Lars German
2017-01-01
The system of cracks developing in reinforced concrete is in many aspects essential when modelling structures in both serviceability- and ultimate limit state. This paper discusses the behavior concerning crack development in flexural members observed from tests and associates it with two different...... existing models. From the investigations an approach is proposed on how to predict the crack pattern in flexural members involving two different crack systems; primary flexural cracks and local secondary cracks. The results of the approach is in overall good agreement with the observed tests and captures...... the pronounced size effect associated with flexural cracking in which the crack spacing and crack widths are approximately proportional to the depth of the member....
Vector optical fields with bipolar symmetry of linear polarization.
Pan, Yue; Li, Yongnan; Li, Si-Min; Ren, Zhi-Cheng; Si, Yu; Tu, Chenghou; Wang, Hui-Tian
2013-09-15
We focus on a new kind of vector optical field with bipolar symmetry of linear polarization instead of cylindrical and elliptical symmetries, enriching members of family of vector optical fields. We design theoretically and generate experimentally the demanded vector optical fields and then explore some novel tightly focusing properties. The geometric configurations of states of polarization provide additional degrees of freedom assisting in engineering the field distribution at the focus to the specific applications such as lithography, optical trapping, and material processing.
Canonical perturbation theory in linearized general relativity theory
Gonzales, R.; Pavlenko, Yu.G.
1986-01-01
Canonical perturbation theory in linearized general relativity theory is developed. It is shown that the evolution of arbitrary dynamic value, conditioned by the interaction of particles, gravitation and electromagnetic fields, can be presented in the form of a series, each member of it corresponding to the contribution of certain spontaneous or induced process. The main concepts of the approach are presented in the approximation of a weak gravitational field
Geneva University honours two CERN staff members
2001-01-01
Albert Hofmann Steve Myers On 8 June, two CERN staff members will receive Geneva University's highest distinction. On the proposal of the University's particle physicists, Steve Myers and Albert Hoffmann, who orchestrated LEP commissioning and operation and were instrumental in its success, will awarded the distinction of doctor honoris causa. The ceremony, interspersed with musical interludes, will be followed by a formal reception and is open to all. The Uni Dufour car park will be free to members of the public attending the ceremony. 8 June 2001 at 10.00 a.m. Uni Dufour, Auditoire Piaget 24, rue Général Dufour, Geneva.
Ferencz, Donald C.; Viterna, Larry A.
1991-01-01
ALPS is a computer program which can be used to solve general linear program (optimization) problems. ALPS was designed for those who have minimal linear programming (LP) knowledge and features a menu-driven scheme to guide the user through the process of creating and solving LP formulations. Once created, the problems can be edited and stored in standard DOS ASCII files to provide portability to various word processors or even other linear programming packages. Unlike many math-oriented LP solvers, ALPS contains an LP parser that reads through the LP formulation and reports several types of errors to the user. ALPS provides a large amount of solution data which is often useful in problem solving. In addition to pure linear programs, ALPS can solve for integer, mixed integer, and binary type problems. Pure linear programs are solved with the revised simplex method. Integer or mixed integer programs are solved initially with the revised simplex, and the completed using the branch-and-bound technique. Binary programs are solved with the method of implicit enumeration. This manual describes how to use ALPS to create, edit, and solve linear programming problems. Instructions for installing ALPS on a PC compatible computer are included in the appendices along with a general introduction to linear programming. A programmers guide is also included for assistance in modifying and maintaining the program.
Linear and quasi-linear equations of parabolic type
Ladyženskaja, O A; Ural′ceva, N N; Uralceva, N N
1968-01-01
Equations of parabolic type are encountered in many areas of mathematics and mathematical physics, and those encountered most frequently are linear and quasi-linear parabolic equations of the second order. In this volume, boundary value problems for such equations are studied from two points of view: solvability, unique or otherwise, and the effect of smoothness properties of the functions entering the initial and boundary conditions on the smoothness of the solutions.
The Theory of Linear Prediction
Vaidyanathan, PP
2007-01-01
Linear prediction theory has had a profound impact in the field of digital signal processing. Although the theory dates back to the early 1940s, its influence can still be seen in applications today. The theory is based on very elegant mathematics and leads to many beautiful insights into statistical signal processing. Although prediction is only a part of the more general topics of linear estimation, filtering, and smoothing, this book focuses on linear prediction. This has enabled detailed discussion of a number of issues that are normally not found in texts. For example, the theory of vecto
Correlation and simple linear regression.
Zou, Kelly H; Tuncali, Kemal; Silverman, Stuart G
2003-06-01
In this tutorial article, the concepts of correlation and regression are reviewed and demonstrated. The authors review and compare two correlation coefficients, the Pearson correlation coefficient and the Spearman rho, for measuring linear and nonlinear relationships between two continuous variables. In the case of measuring the linear relationship between a predictor and an outcome variable, simple linear regression analysis is conducted. These statistical concepts are illustrated by using a data set from published literature to assess a computed tomography-guided interventional technique. These statistical methods are important for exploring the relationships between variables and can be applied to many radiologic studies.
Saravanan, R
2018-01-01
Non-linear optical materials have widespread and promising applications, but the efforts to understand the local structure, electron density distribution and bonding is still lacking. The present work explores the structural details, the electron density distribution and the local bond length distribution of some non-linear optical materials. It also gives estimation of the optical band gap, the particle size, crystallite size, and the elemental composition from UV-Visible analysis, SEM, XRD and EDS of some non-linear optical materials respectively.
Optimal control linear quadratic methods
Anderson, Brian D O
2007-01-01
This augmented edition of a respected text teaches the reader how to use linear quadratic Gaussian methods effectively for the design of control systems. It explores linear optimal control theory from an engineering viewpoint, with step-by-step explanations that show clearly how to make practical use of the material.The three-part treatment begins with the basic theory of the linear regulator/tracker for time-invariant and time-varying systems. The Hamilton-Jacobi equation is introduced using the Principle of Optimality, and the infinite-time problem is considered. The second part outlines the
Migration from New EU Member Countries
Pytlikova, Mariola
2007-01-01
The main purpose of the paper is to give predictions of the migration potential from the 7 new EU member countries to the EEA/EU-13 countries. Being able to analyze 'real' migration behavior from these particular countries over the period 1990-2000 helps me to avoid problems related to (double) o...
Role Orientations of Members of Parliament
Thomassen, Jacques J.A.; Esaiasson, Peter
2006-01-01
To what extent would a change of the Dutch electoral system, strengthening the bond between individual Members of Parliament (MPs) and specific constituencies, improve the quality of political representation, and increase the legitimacy of the political system in the process? In order to answer this
Members' needs, intragroup conflict, and group performance.
Chun, Jinseok S; Choi, Jin Nam
2014-05-01
Focusing on "what people want in their group" as a critical antecedent of intragroup conflict, the present study theorizes and empirically investigates the relationships among the psychological needs of group members, intragroup conflict, and group performance. It attends to the within-group average and dispersion of members' psychological needs and examines the effects stemming from group composition of needs on multiple types of conflict. The analyses based on multisource data from 145 organizational teams revealed significant relationships between the groups' composition with respect to the members' need for achievement and task conflict, need for affiliation and relationship conflict, and need for power and status conflict. Some of these relationships were moderated by open communication among members. The analyses also demonstrated that when the 3 types of conflict were considered together, task conflict was a positive predictor of group performance, whereas relationship conflict was a negative predictor. The findings highlight the motivational aspects of intragroup conflict, revealing the multilevel dynamics of the psychological needs in social settings. (c) 2014 APA, all rights reserved.
Boron--epoxy tubular structure members
Shakespeare, W. B. J.; Nelson, P. T.; Lindkvist, E. C.
1973-01-01
Composite materials fabricate thin-walled tubular members which have same load-carrying capabilities as aluminum, titanium, or other metals, but are lighter. Interface between stepped end fitting and tube lends itself to attachments by primary as well as secondary bonding. Interlaminar shear and hoop stress buildup in attachment at end fitting is avoided.
Phylogenetic relationships among members of the Pachydactylus ...
The Pachydactylus capensis group is a phenetically-defined assemblage of five small-bodied geckos broadly distributed in eastern southern Africa. Several additional small-bodied Pachydactylus have been historically considered subspecies of P. capensis or members of this group. To assess evolutionary relationships ...
WTO Members' Commitments in Education Services
Xu, Jian
2009-01-01
The establishment of World Trade Organization is in line with the conclusion reached at the end of the Uruguay Round in April 1994 by the bulk of the world's trading nations. WTO is in charge of managing multilateral trading system. WTO's "General Agreement on Trade in Services" (GATS) requires member nations to comply with the following…
Issues Causing Stress among Business Faculty Members
Adrian, C. Mitchell; Cox, Susie S.; Phelps, Lonnie D.; Schuldt, Barbara A.; Totten, Jeff W.
2014-01-01
This study examines factors contributing to faculty stress. Factors including demographics, tenure, discipline, and teaching medium are all examined. Whereas once faculty members were inundated with learning new electronic technology (and the stress it created), many appear to have become somewhat comfortable with this change and have adapted to…
Important characteristics of operational force members
Van Heerden, Adelai
2017-10-01
Full Text Available The operational forces military context is generally acknowledged as one of the most stressful contexts as it is demanding of members on a physical, psychological, social level with organisational, intra- and inter-personal demands of an extreme...
Israel, CERN’s new Member State
Anaïs Schaeffer
2014-01-01
On Wednesday, 15 January 2014, the official Israeli Flag-raising Ceremony took place to mark the accession of Israel to Membership of CERN, bringing the Organization’s number of Member States to 21. For more information, click here.
Vogler, Sabine; Habl, Claudia; Bogut, Martina; Vončina, Luka
2011-01-01
Aim To perform a comparative analysis of the pharmaceutical pricing and reimbursement systems in Croatia and the 27 European Union (EU) Member States. Methods Knowledge about the pharmaceutical systems in Croatia and the 27 EU Member States was acquired by literature review and primary research with stakeholders. Results Pharmaceutical prices are controlled at all levels in Croatia, which is also the case in 21 EU Member States. Like many EU countries, Croatia also applies external price referencing, ie, compares prices with other countries. While the wholesale remuneration by a statutorily regulated linear mark-up is applied in Croatia and in several EU countries, the pharmacy compensation for dispensing reimbursable medicines in the form of a flat rate service fee in Croatia is rare among EU countries, which usually apply a linear or regressive pharmacy mark-up scheme. Like in most EU countries, the Croatian Social Insurance reimburses specific medicines at 100%, whereas patients are charged co-payments for other reimbursable medicines. Criteria for reimbursement include the medicine’s importance from the public health perspective, its therapeutic value, and relative effectiveness. In Croatia and in many EU Member States, reimbursement is based on a reference price system. Conclusion The Croatian pharmaceutical system is similar to those in the EU Member States. Key policies, like external price referencing and reference price systems, which have increasingly been introduced in EU countries are also applied in Croatia and serve the same purpose: to ensure access to medicines while containing public pharmaceutical expenditure. PMID:21495202
Vogler, Sabine; Habl, Claudia; Bogut, Martina; Voncina, Luka
2011-04-15
To perform a comparative analysis of the pharmaceutical pricing and reimbursement systems in Croatia and the 27 European Union (EU) Member States. Knowledge about the pharmaceutical systems in Croatia and the 27 EU Member States was acquired by literature review and primary research with stakeholders. Pharmaceutical prices are controlled at all levels in Croatia, which is also the case in 21 EU Member States. Like many EU countries, Croatia also applies external price referencing, i.e., compares prices with other countries. While the wholesale remuneration by a statutorily regulated linear mark-up is applied in Croatia and in several EU countries, the pharmacy compensation for dispensing reimbursable medicines in the form of a flat rate service fee in Croatia is rare among EU countries, which usually apply a linear or regressive pharmacy mark-up scheme. Like in most EU countries, the Croatian Social Insurance reimburses specific medicines at 100%, whereas patients are charged co-payments for other reimbursable medicines. Criteria for reimbursement include the medicine's importance from the public health perspective, its therapeutic value, and relative effectiveness. In Croatia and in many EU Member States, reimbursement is based on a reference price system. The Croatian pharmaceutical system is similar to those in the EU Member States. Key policies, like external price referencing and reference price systems, which have increasingly been introduced in EU countries are also applied in Croatia and serve the same purpose: to ensure access to medicines while containing public pharmaceutical expenditure.
7 CFR 983.42 - Initial members and nomination of successor members.
2010-01-01
...) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF... alternate is selected shall serve in place of that member on the committee, and shall have and be able to... members of the committee shall serve for terms of two years: Provided, That four of the initially selected...
Cellular Automata Rules and Linear Numbers
Nayak, Birendra Kumar; Sahoo, Sudhakar; Biswal, Sagarika
2012-01-01
In this paper, linear Cellular Automta (CA) rules are recursively generated using a binary tree rooted at "0". Some mathematical results on linear as well as non-linear CA rules are derived. Integers associated with linear CA rules are defined as linear numbers and the properties of these linear numbers are studied.
Feedback systems for linear colliders
Hendrickson, L; Himel, Thomas M; Minty, Michiko G; Phinney, N; Raimondi, Pantaleo; Raubenheimer, T O; Shoaee, H; Tenenbaum, P G
1999-01-01
Feedback systems are essential for stable operation of a linear collider, providing a cost-effective method for relaxing tight tolerances. In the Stanford Linear Collider (SLC), feedback controls beam parameters such as trajectory, energy, and intensity throughout the accelerator. A novel dithering optimization system which adjusts final focus parameters to maximize luminosity contributed to achieving record performance in the 1997-98 run. Performance limitations of the steering feedback have been investigated, and improvements have been made. For the Next Linear Collider (NLC), extensive feedback systems are planned as an intregal part of the design. Feedback requiremetns for JLC (the Japanese Linear Collider) are essentially identical to NLC; some of the TESLA requirements are similar but there are significant differences. For NLC, algorithms which incorporate improvements upon the SLC implementation are being prototyped. Specialized systems for the damping rings, rf and interaction point will operate at hi...
An introduction to linear algebra
Mirsky, L
2003-01-01
Rigorous, self-contained coverage of determinants, vectors, matrices and linear equations, quadratic forms, more. Elementary, easily readable account with numerous examples and problems at the end of each chapter.
CLIC: developing a linear collider
Laurent Guiraud
1999-01-01
Compact Linear Collider (CLIC) is a CERN project to provide high-energy electron-positron collisions. Instead of conventional radio-frequency klystrons, CLIC will use a low-energy, high-intensity primary beam to produce acceleration.
1988 linear accelerator conference proceedings
1989-06-01
This report contains papers presented at the 1988 Linear Accelerator Conference. A few topics covered are beam dynamics; beam transport; superconducting components; free electron lasers; ion sources; and klystron research
CERN balances linear collider studies
ILC Newsline
2011-01-01
The forces behind the two most mature proposals for a next-generation collider, the International Linear Collider (ILC) and the Compact Linear Collider (CLIC) study, have been steadily coming together, with scientists from both communities sharing ideas and information across the technology divide. In a support of cooperation between the two, CERN in Switzerland, where most CLIC research takes place, recently converted the project-specific position of CLIC Study Leader to the concept-based Linear Collider Study Leader. The scientist who now holds this position, Steinar Stapnes, is charged with making the linear collider a viable option for CERN’s future, one that could include either CLIC or the ILC. The transition to more involve the ILC must be gradual, he said, and the redefinition of his post is a good start. Though not very much involved with superconducting radiofrequency (SRF) technology, where ILC researchers have made significant advances, CERN participates in many aspect...
Linear Methods for Image Interpolation
Pascal Getreuer
2011-01-01
We discuss linear methods for interpolation, including nearest neighbor, bilinear, bicubic, splines, and sinc interpolation. We focus on separable interpolation, so most of what is said applies to one-dimensional interpolation as well as N-dimensional separable interpolation.
Klumpp, A. R.; Lawson, C. L.
1988-01-01
Routines provided for common scalar, vector, matrix, and quaternion operations. Computer program extends Ada programming language to include linear-algebra capabilities similar to HAS/S programming language. Designed for such avionics applications as software for Space Station.
Acoustic emission linear pulse holography
Collins, H.D.; Busse, L.J.; Lemon, D.K.
1983-10-25
This device relates to the concept of and means for performing Acoustic Emission Linear Pulse Holography, which combines the advantages of linear holographic imaging and Acoustic Emission into a single non-destructive inspection system. This unique system produces a chronological, linear holographic image of a flaw by utilizing the acoustic energy emitted during crack growth. The innovation is the concept of utilizing the crack-generated acoustic emission energy to generate a chronological series of images of a growing crack by applying linear, pulse holographic processing to the acoustic emission data. The process is implemented by placing on a structure an array of piezoelectric sensors (typically 16 or 32 of them) near the defect location. A reference sensor is placed between the defect and the array.
Functionalized linear and cyclic polyolefins
Tuba, Robert; Grubbs, Robert H.
2018-02-13
This invention relates to methods and compositions for preparing linear and cyclic polyolefins. More particularly, the invention relates to methods and compositions for preparing functionalized linear and cyclic polyolefins via olefin metathesis reactions. Polymer products produced via the olefin metathesis reactions of the invention may be utilized for a wide range of materials applications. The invention has utility in the fields of polymer and materials chemistry and manufacture.
Rumen Daskalov
2017-07-01
Full Text Available Let an $[n,k,d]_q$ code be a linear code of length $n$, dimension $k$ and minimum Hamming distance $d$ over $GF(q$. One of the most important problems in coding theory is to construct codes with optimal minimum distances. In this paper 22 new ternary linear codes are presented. Two of them are optimal. All new codes improve the respective lower bounds in [11].
Explorative methods in linear models
Høskuldsson, Agnar
2004-01-01
The author has developed the H-method of mathematical modeling that builds up the model by parts, where each part is optimized with respect to prediction. Besides providing with better predictions than traditional methods, these methods provide with graphic procedures for analyzing different feat...... features in data. These graphic methods extend the well-known methods and results of Principal Component Analysis to any linear model. Here the graphic procedures are applied to linear regression and Ridge Regression....
Polarized Electrons for Linear Colliders
Clendenin, J.
2004-01-01
Future electron-positron linear colliders require a highly polarized electron beam with a pulse structure that depends primarily on whether the acceleration utilizes warm or superconducting rf structures. The International Linear Collider (ILC) will use cold structures for the main linac. It is shown that a dc-biased polarized photoelectron source such as successfully used for the SLC can meet the charge requirements for the ILC micropulse with a polarization approaching 90%
Why 4-H Members Leave: A Study of Discontinuance through Both Current 4-H Members and Former Members
Chilek, Kevin Dwayne
2012-01-01
4-H members quit. It is part of every 4-H program, and according to the research, it is even part of growing up. If only we knew why they quit, we could possibly do something about it. To date, the reasons youth join 4-H have been more thoroughly researched than the reasons they quit. This study explores why youth choose to discontinue membership…
Radiogenic leukemia risk analysis for the Techa River Cohort members
Krestinina, L.Y.; Epifanova, S.B.; Akleyev, A.V.; Preston, D.; Davis, F.; Ron, E.
2008-01-01
Full text: Members of the Techa River Cohort have been exposed to a long-term external and internal irradiation due to releases of radioactive waste from the Mayak Production Association into the Techa River. Since internal exposure resulted primarily from incorporation of 90 Sr in the bone structure, the bone marrow was the principal target. The maximum dose to the red bone marrow accumulated over 50 years in cohort members reached 2 Gy, and the mean dose was 0.3 Gy. The epidemiological analysis of radiogenic risk of leukemia development was conducted based on the retrospective cohort study approach and regression analysis using the Epicure statistical packet. The extended Techa River Cohort (ETRC) includes about 30 thousand people of the two genders, various ages and different ethnicity (mostly Russians, Tartars and Bashkirs). The catchment area for leukemia mortality and incidence follow-up includes the whole Chelyabinsk and Kurgan Oblasts. The previous analysis of leukemia mortality risk for a 50-year follow-up period pointed out statistically significant dose dependence. The presentation will for the first time describe the results of leukemia incidence risk analyses for the period from 1953 through 2004. Over this 52-year follow-up period 92 leukemia cases (42 in men and 50 in women) were registered among ETRC members resident in the catchment area. Among those 92 cases there were 22 cases attributed to chronic lymphoid leukemia (12 in men and 10 in women). The preliminary analysis of leukemia incidence risk showed a statistically significant linear dependence on dose for total leukemias (p = 0.006), as well as for leukemias with CLL excluded (p < 0.001). The point value of the total leukemia incidence ERR was 2.0/Gy (95% CI: 0.4-15.4) and for leukemia with CLL excluded the ERR was 4.5/Gy (95% CI: 1.1-14.7). More than 57% of leukemia cases (excluding CLL) registered in ETRC members could be related to the radiogenic factor. Analyses of chronic lymphoid
Primordial black holes in linear and non-linear regimes
Allahyari, Alireza; Abolhasani, Ali Akbar [Department of Physics, Sharif University of Technology, Tehran (Iran, Islamic Republic of); Firouzjaee, Javad T., E-mail: allahyari@physics.sharif.edu, E-mail: j.taghizadeh.f@ipm.ir [School of Astronomy, Institute for Research in Fundamental Sciences (IPM), P.O. Box 19395-5531, Tehran (Iran, Islamic Republic of)
2017-06-01
We revisit the formation of primordial black holes (PBHs) in the radiation-dominated era for both linear and non-linear regimes, elaborating on the concept of an apparent horizon. Contrary to the expectation from vacuum models, we argue that in a cosmological setting a density fluctuation with a high density does not always collapse to a black hole. To this end, we first elaborate on the perturbation theory for spherically symmetric space times in the linear regime. Thereby, we introduce two gauges. This allows to introduce a well defined gauge-invariant quantity for the expansion of null geodesics. Using this quantity, we argue that PBHs do not form in the linear regime irrespective of the density of the background. Finally, we consider the formation of PBHs in non-linear regimes, adopting the spherical collapse picture. In this picture, over-densities are modeled by closed FRW models in the radiation-dominated era. The difference of our approach is that we start by finding an exact solution for a closed radiation-dominated universe. This yields exact results for turn-around time and radius. It is important that we take the initial conditions from the linear perturbation theory. Additionally, instead of using uniform Hubble gauge condition, both density and velocity perturbations are admitted in this approach. Thereby, the matching condition will impose an important constraint on the initial velocity perturbations δ {sup h} {sub 0} = −δ{sub 0}/2. This can be extended to higher orders. Using this constraint, we find that the apparent horizon of a PBH forms when δ > 3 at turn-around time. The corrections also appear from the third order. Moreover, a PBH forms when its apparent horizon is outside the sound horizon at the re-entry time. Applying this condition, we infer that the threshold value of the density perturbations at horizon re-entry should be larger than δ {sub th} > 0.7.
Members of the Forum Engelberg visit CERN
Patrive Loïez
2002-01-01
The Forum Engelberg is an annual interdisciplinary conference held in Engelberg, Switzerland intended to act as an international platform for debate and exchange of views on key issues affecting scientific research, technology, economics and philosophy. Its President is Hubert Curien - former French Minister of Research and Space Research, and President of the CERN Council from 1994 to 1996. Photo 01: CERN Director-General Prof. Luciano Maiani (left) speaks to Forum members and public figures from the Geneva area during the visit. In the background is Jean-Claude Landry from the Department of the Interior, Agriculture and Environment, State of Geneva. Photo 02: CERN Director-General Prof. Luciano Maiani (left) speaks to Forum members and public figures from the Geneva area during the visit. In the background is Bernard Ecoffey, Founder of the Forum Engelberg.
Surface modifying method for metal member
Amano, Kazuo; Enomoto, Kunio; Hirano, Akihiko; Hirano, Atsuya; Hattori, Shigeo; Hayashi, Eisaku; Ueyama, Toshiharu; Hayashi, Makoto
1998-01-01
A surface of a metal member such as carbon steel to be used in a corrosion circumstance such as in a nuclear power plant and a thermoelectric plant are polished. A printing method is conducted for removing obstacles on the surface of the member. Namely, a photographing printing paper immersed in a diluted sulfuric acid solution is appended tightly to the portion with its surface polished smoothly. Sulfur present in the form of an obstacle of MnS or present alone in the material reacts with the sulfuric acid to form a sulfuric acid gas, and reacts with Ag of the printing paper to discolor the printing paper to brown. When a peeled printing paper is discolored to brown, sulfur printing is repeated. After conforming that the peeled printing paper is white, the surface is washed. Subsequently, surface plasticization is conducted by water jet peening or shot peening. (I.N.)
Identifying New Members of Nearby Moving Groups
Holmbeck, Erika; Vican, Laura
2014-06-01
Our group has assembled a sample of 14,000 stars of spectral types B9-M9 with measured UVW Galactic space velocities and lying within 125 pc of Earth. We have identified candidate members of three nearby young (less than 100 Myr) moving groups. For stars of spectral types G5 and later, we have used the Kast spectrometer on the Shane 3m telescope at Lick Observatory to measure lithium abundance in order to determine stellar ages. With the data we have obtained from this run, we will be able to establish whether our candidates are bona fide members of the moving groups in question. I will be presenting the preliminary results from this survey, including spectra of the ~50 stars observed thus far. These nearby young stars will make excellent targets for direct imaging followup surveys, since any giant planets around young stars will still be warm, and will therefore be bright enough to detect with instruments like GPI.
Lithuania to become Associate Member of CERN
Dačkus, Robertas
2017-01-01
On 27 June 2017, in Vilnius, Lithuania, CERN Director General, Fabiola Gianotti, and the Minister of Foreign Affairs of the Republic of Lithuania, Linas Linkevičius, in the presence of the President of the Republic of Lithuania, Dalia Grybauskaitė, signed the Agreement admitting Lithuania as an Associate Member of CERN. The last step for the Agreement to enter into force requires final approval by the Government of Lithuania.
Mapping organizational members' sense of fit
Billsberry, Jon; Marsh, Philip; Moss-Jones, John
2004-01-01
Despite its importance in the organizational behavior literature, person–organization (P–O) fit remains an elusive construct. One reason for this is the lack of research about organizational members’ own sense of their P–O fit. In this paper we report an empirical study that explored organizational members’ own sense of fit using storytelling and causal mapping techniques. The results suggest that organizational members categorize their perceptions of their fit into five discrete domains (job...
Service Member Suicide and Readiness: An Analysis
2017-05-25
command, and degrades the morale of those still serving, as well as the American public.8 A shrinking number of qualified volunteers and reductions...to Sri Aurobindo’s Philosophy of Integral Non-Dualism,” in The Integral Philosophy of Sri Aurobindo, ed. Haridas Chaudhuri and Frederic Spiegelberg...potentially unsolvable problem should not prevent attempts to develop solutions. In a moral sense, service member suicide should elicit greater diligence
Member State Event: Telling CERN's story !
2004-01-01
As part of the events to mark the Laboratory's fiftieth anniversary, members of the CERN personnel are telling the story of CERN. Robert Cailliau (on the right), currently responsible for CERN's external communications, and Chiara Mariotti (in the center), a physicist working at CMS, were invited to talk about the history of CERN and the Web at a conference in the 'Science Thursdays' series entitled 'From the Quark to the Web' in Turin on 26 February.
Members of the Forum Engelberg visit CERN
Patrice Loïez
2002-01-01
The Forum Engelberg is an annual interdisciplinary conference held in Engelberg, Switzerland intended to act as an international platform for debate and exchange of views on key issues affecting scientific research, technology, economics and philosophy. Its President is Hubert Curien - former French Minister of Research and Space Research, and President of the CERN Council from 1994 to 1996. He is pictured here (right) alongside CERN Director-General Prof. Luciano Maiani during the visit of Forum members to CERN.
REGISTRATION OF VEHICLES IN SWITZERLAND: MEMBERS OF THE FAMILY OF A MEMBER OF THE PERSONNEL
Service des Relations avec les Pays Hôtes
1999-01-01
The Permanent Mission of Switzerland to the International Organisations in Geneva has informed CERN that members of the family of a member of the personnel who hold a carte delégitimation or a Ci permit may not register a vehicle in Switzerland. Only those members of the family who are of Swiss nationality or hold an ordinary permit (e.g. a 'B' or 'C' permit) may register vehicles in their own names.Relations with the Host States Servicehttp://www.cern.ch/relations/Tel. 72848
Member State Event: Telling CERN's Story
2004-01-01
As part of the events to mark the Laboratory's fiftieth anniversary, members of the CERN personnel are telling the story of CERN. Robert Cailliau (on the right of the photograph), co-inventor of the Web and currently responsible for CERN's external communications, and Chiara Mariotti (in the center), a physicist working at CMS, were invited to talk about the history of CERN and the Web at a conference in the 'Science Thursdays' series entitled 'From the Quark to the Web' in Turin on 26 February. This was not their first appearance before a non-specialist audience (almost 1000 people that day!) eager to find out what goes on in a unique research centre like CERN as talking about the Laboratory's activities and its history are part and parcel of their work for the Organization. Anniversary Events in the Member States: This 'Science Thursday' event devoted to CERN was one of Italy's contributions to CERN's fiftieth anniversary celebrations. Coming up soon in the Member States: Italy International Centre...
Variable linear motion cycle monitoring device
Ezekoye, L.I.; Cavada, D.R.
1989-01-01
A pressurized water reactor nuclear power plant is described including feedwater flow control valve having a valve member which can be moved varying amounts in discrete movements in either direction between an open and a closed position to control feedwater flow; and apparatus for recording cycles of reciprocal movement of the valve member. The apparatus consists of: a travel translator member, means connecting the travel translator member to the valve member for reciprocal rectilinear movement in direction corresponding to, and for a distance proportional to, the movement of the valve member, a shaft member for rotation its longitudinal axis, means for limiting angular rotation of the shaft member in each direction; means for counting cycles of reciprocal rotation of the shaft member between rotating limits set by the limiting mean; a wheel mounted on the shaft member and in engagement with the travel translator member the wheel translating movement of the travel translator into rotation of the shaft member between the limits of rotation of the shaft member set by the limit means, and means permitting relative movement between the wheel and one of the member once the limits of rotation of the shaft member are reached and the travel translator member continues movement in the same direction
The linear-non-linear frontier for the Goldstone Higgs
Gavela, M.B.; Saa, S.; Kanshin, K.; Machado, P.A.N.
2016-01-01
The minimal SO(5)/SO(4) σ-model is used as a template for the ultraviolet completion of scenarios in which the Higgs particle is a low-energy remnant of some high-energy dynamics, enjoying a (pseudo) Nambu-Goldstone-boson ancestry. Varying the σ mass allows one to sweep from the perturbative regime to the customary non-linear implementations. The low-energy benchmark effective non-linear Lagrangian for bosons and fermions is obtained, determining as well the operator coefficients including linear corrections. At first order in the latter, three effective bosonic operators emerge which are independent of the explicit soft breaking assumed. The Higgs couplings to vector bosons and fermions turn out to be quite universal: the linear corrections are proportional to the explicit symmetry-breaking parameters. Furthermore, we define an effective Yukawa operator which allows a simple parametrization and comparison of different heavy-fermion ultraviolet completions. In addition, one particular fermionic completion is explored in detail, obtaining the corresponding leading low-energy fermionic operators. (orig.)
Advanced statistics: linear regression, part II: multiple linear regression.
Marill, Keith A
2004-01-01
The applications of simple linear regression in medical research are limited, because in most situations, there are multiple relevant predictor variables. Univariate statistical techniques such as simple linear regression use a single predictor variable, and they often may be mathematically correct but clinically misleading. Multiple linear regression is a mathematical technique used to model the relationship between multiple independent predictor variables and a single dependent outcome variable. It is used in medical research to model observational data, as well as in diagnostic and therapeutic studies in which the outcome is dependent on more than one factor. Although the technique generally is limited to data that can be expressed with a linear function, it benefits from a well-developed mathematical framework that yields unique solutions and exact confidence intervals for regression coefficients. Building on Part I of this series, this article acquaints the reader with some of the important concepts in multiple regression analysis. These include multicollinearity, interaction effects, and an expansion of the discussion of inference testing, leverage, and variable transformations to multivariate models. Examples from the first article in this series are expanded on using a primarily graphic, rather than mathematical, approach. The importance of the relationships among the predictor variables and the dependence of the multivariate model coefficients on the choice of these variables are stressed. Finally, concepts in regression model building are discussed.
The linear-non-linear frontier for the Goldstone Higgs
Gavela, M.B.; Saa, S. [IFT-UAM/CSIC, Universidad Autonoma de Madrid, Departamento de Fisica Teorica y Instituto de Fisica Teorica, Madrid (Spain); Kanshin, K. [Universita di Padova, Dipartimento di Fisica e Astronomia ' G. Galilei' , Padua (Italy); INFN, Padova (Italy); Machado, P.A.N. [IFT-UAM/CSIC, Universidad Autonoma de Madrid, Departamento de Fisica Teorica y Instituto de Fisica Teorica, Madrid (Spain); Fermi National Accelerator Laboratory, Theoretical Physics Department, Batavia, IL (United States)
2016-12-15
The minimal SO(5)/SO(4) σ-model is used as a template for the ultraviolet completion of scenarios in which the Higgs particle is a low-energy remnant of some high-energy dynamics, enjoying a (pseudo) Nambu-Goldstone-boson ancestry. Varying the σ mass allows one to sweep from the perturbative regime to the customary non-linear implementations. The low-energy benchmark effective non-linear Lagrangian for bosons and fermions is obtained, determining as well the operator coefficients including linear corrections. At first order in the latter, three effective bosonic operators emerge which are independent of the explicit soft breaking assumed. The Higgs couplings to vector bosons and fermions turn out to be quite universal: the linear corrections are proportional to the explicit symmetry-breaking parameters. Furthermore, we define an effective Yukawa operator which allows a simple parametrization and comparison of different heavy-fermion ultraviolet completions. In addition, one particular fermionic completion is explored in detail, obtaining the corresponding leading low-energy fermionic operators. (orig.)
Linearization: Geometric, Complex, and Conditional
Asghar Qadir
2012-01-01
Full Text Available Lie symmetry analysis provides a systematic method of obtaining exact solutions of nonlinear (systems of differential equations, whether partial or ordinary. Of special interest is the procedure that Lie developed to transform scalar nonlinear second-order ordinary differential equations to linear form. Not much work was done in this direction to start with, but recently there have been various developments. Here, first the original work of Lie (and the early developments on it, and then more recent developments based on geometry and complex analysis, apart from Lie’s own method of algebra (namely, Lie group theory, are reviewed. It is relevant to mention that much of the work is not linearization but uses the base of linearization.
Window observers for linear systems
Utkin Vadim
2000-01-01
Full Text Available Given a linear system x ˙ = A x + B u with output y = C x and a window function ω ( t , i.e., ∀ t , ω ( t ∈ {0,1 }, and assuming that the window function is Lebesgue measurable, we refer to the following observer, x ˆ = A x + B u + ω ( t L C ( x − x ˆ as a window observer. The stability issue is treated in this paper. It is proven that for linear time-invariant systems, the window observer can be stabilized by an appropriate design under a very mild condition on the window functions, albeit for linear time-varying system, some regularity of the window functions is required to achieve observer designs with the asymptotic stability. The corresponding design methods are developed. An example is included to illustrate the possible applications
Topics in quaternion linear algebra
Rodman, Leiba
2014-01-01
Quaternions are a number system that has become increasingly useful for representing the rotations of objects in three-dimensional space and has important applications in theoretical and applied mathematics, physics, computer science, and engineering. This is the first book to provide a systematic, accessible, and self-contained exposition of quaternion linear algebra. It features previously unpublished research results with complete proofs and many open problems at various levels, as well as more than 200 exercises to facilitate use by students and instructors. Applications presented in the book include numerical ranges, invariant semidefinite subspaces, differential equations with symmetries, and matrix equations. Designed for researchers and students across a variety of disciplines, the book can be read by anyone with a background in linear algebra, rudimentary complex analysis, and some multivariable calculus. Instructors will find it useful as a complementary text for undergraduate linear algebra courses...
Towards the International Linear Collider
Lopez-Fernandez, Ricardo
2006-01-01
The broad physics potential of e+e- linear colliders was recognized by the high energy physics community right after the end of LEP in 2000. In 2007, the Large Hadron Collider (LHC) now under construction at CERN will obtain its first collisions. The LHC, colliding protons with protons at 14 TeV, will discover a standard model Higgs boson over the full potential mass range, and should be sensitive to new physics into the several TeV range. The program for the Linear Collider (LC) will be set in the context of the discoveries made at the LHC. All the proposals for a Linear Collider will extend the discoveries and provide a wealth of measurements that are essential for giving deeper understanding of their meaning, and pointing the way to further evolution of particle physics in the future. For the mexican groups is the right time to join such an effort
Linear Synchronous Motor Repeatability Tests
Ward, C.R.
2002-01-01
A cart system using linear synchronous motors was being considered for the Plutonium Immobilization Plant (PIP). One of the applications in the PIP was the movement of a stack of furnace trays, filled with the waste form (pucks) from a stacking/unstacking station to several bottom loaded furnaces. A system was ordered to perform this function in the PIP Ceramic Prototype Test Facility (CPTF). This system was installed and started up in SRTC prior to being installed in the CPTF. The PIP was suspended and then canceled after the linear synchronous motor system was started up. This system was used to determine repeatability of a linear synchronous motor cart system for the Modern Pit Facility
Linearly polarized photons at ELSA
Eberhardt, Holger [Physikalisches Institut, Universitaet Bonn (Germany)
2009-07-01
To investigate the nucleon resonance regime in meson photoproduction, double polarization experiments are currently performed at the electron accelerator ELSA in Bonn. The experiments make use of a polarized target and circularly or linearly polarized photon beams. Linearly polarized photons are produced by coherent bremsstrahlung from an accurately aligned diamond crystal. The orientation of the crystal with respect to the electron beam is measured using the Stonehenge-Technique. Both, the energy of maximum polarization and the plane of polarization, can be deliberately chosen for the experiment. The linearly polarized beam provides the basis for the measurement of azimuthal beam asymmetries, such as {sigma} (unpolarized target) and G (polarized target). These observables are extracted in various single and multiple meson photoproduction channels.
Linear programming foundations and extensions
Vanderbei, Robert J
2001-01-01
Linear Programming: Foundations and Extensions is an introduction to the field of optimization. The book emphasizes constrained optimization, beginning with a substantial treatment of linear programming, and proceeding to convex analysis, network flows, integer programming, quadratic programming, and convex optimization. The book is carefully written. Specific examples and concrete algorithms precede more abstract topics. Topics are clearly developed with a large number of numerical examples worked out in detail. Moreover, Linear Programming: Foundations and Extensions underscores the purpose of optimization: to solve practical problems on a computer. Accordingly, the book is coordinated with free efficient C programs that implement the major algorithms studied: -The two-phase simplex method; -The primal-dual simplex method; -The path-following interior-point method; -The homogeneous self-dual methods. In addition, there are online JAVA applets that illustrate various pivot rules and variants of the simplex m...
Uniqueness theorems in linear elasticity
Knops, Robin John
1971-01-01
The classical result for uniqueness in elasticity theory is due to Kirchhoff. It states that the standard mixed boundary value problem for a homogeneous isotropic linear elastic material in equilibrium and occupying a bounded three-dimensional region of space possesses at most one solution in the classical sense, provided the Lame and shear moduli, A and J1 respectively, obey the inequalities (3 A + 2 J1) > 0 and J1>O. In linear elastodynamics the analogous result, due to Neumann, is that the initial-mixed boundary value problem possesses at most one solution provided the elastic moduli satisfy the same set of inequalities as in Kirchhoffs theorem. Most standard textbooks on the linear theory of elasticity mention only these two classical criteria for uniqueness and neglect altogether the abundant literature which has appeared since the original publications of Kirchhoff. To remedy this deficiency it seems appropriate to attempt a coherent description ofthe various contributions made to the study of uniquenes...
Bayes linear statistics, theory & methods
Goldstein, Michael
2007-01-01
Bayesian methods combine information available from data with any prior information available from expert knowledge. The Bayes linear approach follows this path, offering a quantitative structure for expressing beliefs, and systematic methods for adjusting these beliefs, given observational data. The methodology differs from the full Bayesian methodology in that it establishes simpler approaches to belief specification and analysis based around expectation judgements. Bayes Linear Statistics presents an authoritative account of this approach, explaining the foundations, theory, methodology, and practicalities of this important field. The text provides a thorough coverage of Bayes linear analysis, from the development of the basic language to the collection of algebraic results needed for efficient implementation, with detailed practical examples. The book covers:The importance of partial prior specifications for complex problems where it is difficult to supply a meaningful full prior probability specification...
Scalar-tensor linear inflation
Artymowski, Michał [Institute of Physics, Jagiellonian University, Łojasiewicza 11, 30-348 Kraków (Poland); Racioppi, Antonio, E-mail: Michal.Artymowski@uj.edu.pl, E-mail: Antonio.Racioppi@kbfi.ee [National Institute of Chemical Physics and Biophysics, Rävala 10, 10143 Tallinn (Estonia)
2017-04-01
We investigate two approaches to non-minimally coupled gravity theories which present linear inflation as attractor solution: a) the scalar-tensor theory approach, where we look for a scalar-tensor theory that would restore results of linear inflation in the strong coupling limit for a non-minimal coupling to gravity of the form of f (φ) R /2; b) the particle physics approach, where we motivate the form of the Jordan frame potential by loop corrections to the inflaton field. In both cases the Jordan frame potentials are modifications of the induced gravity inflationary scenario, but instead of the Starobinsky attractor they lead to linear inflation in the strong coupling limit.
Permafrost Hazards and Linear Infrastructure
Stanilovskaya, Julia; Sergeev, Dmitry
2014-05-01
The international experience of linear infrastructure planning, construction and exploitation in permafrost zone is being directly tied to the permafrost hazard assessment. That procedure should also consider the factors of climate impact and infrastructure protection. The current global climate change hotspots are currently polar and mountain areas. Temperature rise, precipitation and land ice conditions change, early springs occur more often. The big linear infrastructure objects cross the territories with different permafrost conditions which are sensitive to the changes in air temperature, hydrology, and snow accumulation which are connected to climatic dynamics. One of the most extensive linear structures built on permafrost worldwide are Trans Alaskan Pipeline (USA), Alaska Highway (Canada), Qinghai-Xizang Railway (China) and Eastern Siberia - Pacific Ocean Oil Pipeline (Russia). Those are currently being influenced by the regional climate change and permafrost impact which may act differently from place to place. Thermokarst is deemed to be the most dangerous process for linear engineering structures. Its formation and development depend on the linear structure type: road or pipeline, elevated or buried one. Zonal climate and geocryological conditions are also of the determining importance here. All the projects are of the different age and some of them were implemented under different climatic conditions. The effects of permafrost thawing have been recorded every year since then. The exploration and transportation companies from different countries maintain the linear infrastructure from permafrost degradation in different ways. The highways in Alaska are in a good condition due to governmental expenses on annual reconstructions. The Chara-China Railroad in Russia is under non-standard condition due to intensive permafrost response. Standards for engineering and construction should be reviewed and updated to account for permafrost hazards caused by the
A Linear Electromagnetic Piston Pump
Hogan, Paul H.
Advancements in mobile hydraulics for human-scale applications have increased demand for a compact hydraulic power supply. Conventional designs couple a rotating electric motor to a hydraulic pump, which increases the package volume and requires several energy conversions. This thesis investigates the use of a free piston as the moving element in a linear motor to eliminate multiple energy conversions and decrease the overall package volume. A coupled model used a quasi-static magnetic equivalent circuit to calculate the motor inductance and the electromagnetic force acting on the piston. The force was an input to a time domain model to evaluate the mechanical and pressure dynamics. The magnetic circuit model was validated with finite element analysis and an experimental prototype linear motor. The coupled model was optimized using a multi-objective genetic algorithm to explore the parameter space and maximize power density and efficiency. An experimental prototype linear pump coupled pistons to an off-the-shelf linear motor to validate the mechanical and pressure dynamics models. The magnetic circuit force calculation agreed within 3% of finite element analysis, and within 8% of experimental data from the unoptimized prototype linear motor. The optimized motor geometry also had good agreement with FEA; at zero piston displacement, the magnetic circuit calculates optimized motor force within 10% of FEA in less than 1/1000 the computational time. This makes it well suited to genetic optimization algorithms. The mechanical model agrees very well with the experimental piston pump position data when tuned for additional unmodeled mechanical friction. Optimized results suggest that an improvement of 400% of the state of the art power density is attainable with as high as 85% net efficiency. This demonstrates that a linear electromagnetic piston pump has potential to serve as a more compact and efficient supply of fluid power for the human scale.
Sparse Linear Identifiable Multivariate Modeling
Henao, Ricardo; Winther, Ole
2011-01-01
and bench-marked on artificial and real biological data sets. SLIM is closest in spirit to LiNGAM (Shimizu et al., 2006), but differs substantially in inference, Bayesian network structure learning and model comparison. Experimentally, SLIM performs equally well or better than LiNGAM with comparable......In this paper we consider sparse and identifiable linear latent variable (factor) and linear Bayesian network models for parsimonious analysis of multivariate data. We propose a computationally efficient method for joint parameter and model inference, and model comparison. It consists of a fully...
Quantized, piecewise linear filter network
Sørensen, John Aasted
1993-01-01
A quantization based piecewise linear filter network is defined. A method for the training of this network based on local approximation in the input space is devised. The training is carried out by repeatedly alternating between vector quantization of the training set into quantization classes...... and equalization of the quantization classes linear filter mean square training errors. The equalization of the mean square training errors is carried out by adapting the boundaries between neighbor quantization classes such that the differences in mean square training errors are reduced...
Correct Linearization of Einstein's Equations
Rabounski D.
2006-06-01
Full Text Available Regularly Einstein's equations can be reduced to a wave form (linearly dependent from the second derivatives of the space metric in the absence of gravitation, the space rotation and Christoffel's symbols. As shown here, the origin of the problem is that one uses the general covariant theory of measurement. Here the wave form of Einstein's equations is obtained in the terms of Zelmanov's chronometric invariants (physically observable projections on the observer's time line and spatial section. The obtained equations depend on solely the second derivatives even if gravitation, the space rotation and Christoffel's symbols. The correct linearization proves: the Einstein equations are completely compatible with weak waves of the metric.
Basic linear partial differential equations
Treves, Francois
1975-01-01
Focusing on the archetypes of linear partial differential equations, this text for upper-level undergraduates and graduate students features most of the basic classical results. The methods, however, are decidedly nontraditional: in practically every instance, they tend toward a high level of abstraction. This approach recalls classical material to contemporary analysts in a language they can understand, as well as exploiting the field's wealth of examples as an introduction to modern theories.The four-part treatment covers the basic examples of linear partial differential equations and their
Introduction to computational linear algebra
Nassif, Nabil; Erhel, Jocelyne
2015-01-01
Introduction to Computational Linear Algebra introduces the reader with a background in basic mathematics and computer programming to the fundamentals of dense and sparse matrix computations with illustrating examples. The textbook is a synthesis of conceptual and practical topics in ""Matrix Computations."" The book's learning outcomes are twofold: to understand state-of-the-art computational tools to solve matrix computations problems (BLAS primitives, MATLAB® programming) as well as essential mathematical concepts needed to master the topics of numerical linear algebra. It is suitable for s
Linear feedback controls the essentials
Haidekker, Mark A
2013-01-01
The design of control systems is at the very core of engineering. Feedback controls are ubiquitous, ranging from simple room thermostats to airplane engine control. Helping to make sense of this wide-ranging field, this book provides a new approach by keeping a tight focus on the essentials with a limited, yet consistent set of examples. Analysis and design methods are explained in terms of theory and practice. The book covers classical, linear feedback controls, and linear approximations are used when needed. In parallel, the book covers time-discrete (digital) control systems and juxtapos
Passive longitudinal phase space linearizer
P. Craievich
2010-03-01
Full Text Available We report on the possibility to passively linearize the bunch compression process in electron linacs for the next generation x-ray free electron lasers. This can be done by using the monopole wakefields in a dielectric-lined waveguide. The optimum longitudinal voltage loss over the length of the bunch is calculated in order to compensate both the second-order rf time curvature and the second-order momentum compaction terms. Thus, the longitudinal phase space after the compression process is linearized up to a fourth-order term introduced by the convolution between the bunch and the monopole wake function.
Generalized, Linear, and Mixed Models
McCulloch, Charles E; Neuhaus, John M
2011-01-01
An accessible and self-contained introduction to statistical models-now in a modernized new editionGeneralized, Linear, and Mixed Models, Second Edition provides an up-to-date treatment of the essential techniques for developing and applying a wide variety of statistical models. The book presents thorough and unified coverage of the theory behind generalized, linear, and mixed models and highlights their similarities and differences in various construction, application, and computational aspects.A clear introduction to the basic ideas of fixed effects models, random effects models, and mixed m
Emittance control in linear colliders
Ruth, R.D.
1991-01-01
Before completing a realistic design of a next-generation linear collider, the authors must first learn the lessons taught by the first generation, the SLC. Given that, they must make designs fault tolerant by including correction and compensation in the basic design. They must also try to eliminate these faults by improved alignment and stability of components. When these two efforts cross, they have a realistic design. The techniques of generation and control of emittance reviewed here provide a foundation for a design which can obtain the necessary luminosity in a next-generation linear collider
Linear contextual modal type theory
Schack-Nielsen, Anders; Schürmann, Carsten
Abstract. When one implements a logical framework based on linear type theory, for example the Celf system [?], one is immediately con- fronted with questions about their equational theory and how to deal with logic variables. In this paper, we propose linear contextual modal type theory that gives...... a mathematical account of the nature of logic variables. Our type theory is conservative over intuitionistic contextual modal type theory proposed by Nanevski, Pfenning, and Pientka. Our main contributions include a mechanically checked proof of soundness and a working implementation....
A Non-Member Spouse's Entitlement To The Member's Pension Interest
Motseotsile Clement Marumoagae
2014-12-01
Full Text Available It is important that married couples seek legal advice with regard to the assets falling within their joint estate, more particularly their retirement benefits. This article reflects on the entitlement (if any of non-member spouses to their spouses' retirement fund benefits. Pension benefits can be due before, during or after divorce, and parties to the marriage should be aware of their rights with regard to the accruing pension benefits of their spouses. While it is settled law that non-member spouses are entitled to receive a portion of their member spouses' pension benefits (known as "pension interest" immediately on divorce, it is not particularly clear whether non-member spouses are also entitled to receive the same before or sometime after divorce. In this article I provide a contextual understanding of the entitlements (if any which spouses or former spouses of members of pension funds have on such member spouses' retirement benefits. Furthermore, it shown in this article that various divisions of South African High Courts have been inconsistent in how they have approached the issue of the pension interest between divorcing spouses or divorced ex-spouses.
Vanilla Technicolor at Linear Colliders
T. Frandsen, Mads; Jarvinen, Matti; Sannino, Francesco
2011-01-01
We analyze the reach of Linear Colliders (LC)s for models of dynamical electroweak symmetry breaking. We show that LCs can efficiently test the compositeness scale, identified with the mass of the new spin-one resonances, till the maximum energy in the center-of-mass of the colliding leptons. In ...
Variational linear algebraic equations method
Moiseiwitsch, B.L.
1982-01-01
A modification of the linear algebraic equations method is described which ensures a variational bound on the phaseshifts for potentials having a definite sign at all points. The method is illustrated by the elastic scattering of s-wave electrons by the static field of atomic hydrogen. (author)
Feedback Systems for Linear Colliders
1999-01-01
Feedback systems are essential for stable operation of a linear collider, providing a cost-effective method for relaxing tight tolerances. In the Stanford Linear Collider (SLC), feedback controls beam parameters such as trajectory, energy, and intensity throughout the accelerator. A novel dithering optimization system which adjusts final focus parameters to maximize luminosity contributed to achieving record performance in the 1997-98 run. Performance limitations of the steering feedback have been investigated, and improvements have been made. For the Next Linear Collider (NLC), extensive feedback systems are planned as an integral part of the design. Feedback requirements for JLC (the Japanese Linear Collider) are essentially identical to NLC; some of the TESLA requirements are similar but there are significant differences. For NLC, algorithms which incorporate improvements upon the SLC implementation are being prototyped. Specialized systems for the damping rings, rf and interaction point will operate at high bandwidth and fast response. To correct for the motion of individual bunches within a train, both feedforward and feedback systems are planned. SLC experience has shown that feedback systems are an invaluable operational tool for decoupling systems, allowing precision tuning, and providing pulse-to-pulse diagnostics. Feedback systems for the NLC will incorporate the key SLC features and the benefits of advancing technologies
Aspects of robust linear regression
Davies, P.L.
1993-01-01
Section 1 of the paper contains a general discussion of robustness. In Section 2 the influence function of the Hampel-Rousseeuw least median of squares estimator is derived. Linearly invariant weak metrics are constructed in Section 3. It is shown in Section 4 that $S$-estimators satisfy an exact
Periodic linear differential stochastic processes
Kwakernaak, H.
1975-01-01
Periodic linear differential processes are defined and their properties are analyzed. Equivalent representations are discussed, and the solutions of related optimal estimation problems are given. An extension is presented of Kailath and Geesey’s [1] results concerning the innovations representation
Linear colliders for photon collisions
Anon.
1994-01-01
The enthusiasm of the first international workshop on photonphoton colliders and associated physics, held at the Lawrence Berkeley Laboratory from 28 March - 1 April, could have set a ball rolling. According to proponents of this physics, the particle physics one can study with a high energy linear collider is special and complements that of a hadron supercollider
Saturation and linear transport equation
Kutak, K.
2009-03-01
We show that the GBW saturation model provides an exact solution to the one dimensional linear transport equation. We also show that it is motivated by the BK equation considered in the saturated regime when the diffusion and the splitting term in the diffusive approximation are balanced by the nonlinear term. (orig.)
Parameterized Linear Longitudinal Airship Model
Kulczycki, Eric; Elfes, Alberto; Bayard, David; Quadrelli, Marco; Johnson, Joseph
2010-01-01
A parameterized linear mathematical model of the longitudinal dynamics of an airship is undergoing development. This model is intended to be used in designing control systems for future airships that would operate in the atmospheres of Earth and remote planets. Heretofore, the development of linearized models of the longitudinal dynamics of airships has been costly in that it has been necessary to perform extensive flight testing and to use system-identification techniques to construct models that fit the flight-test data. The present model is a generic one that can be relatively easily specialized to approximate the dynamics of specific airships at specific operating points, without need for further system identification, and with significantly less flight testing. The approach taken in the present development is to merge the linearized dynamical equations of an airship with techniques for estimation of aircraft stability derivatives, and to thereby make it possible to construct a linearized dynamical model of the longitudinal dynamics of a specific airship from geometric and aerodynamic data pertaining to that airship. (It is also planned to develop a model of the lateral dynamics by use of the same methods.) All of the aerodynamic data needed to construct the model of a specific airship can be obtained from wind-tunnel testing and computational fluid dynamics
Linear Methods for Image Interpolation
Pascal Getreuer
2011-09-01
Full Text Available We discuss linear methods for interpolation, including nearest neighbor, bilinear, bicubic, splines, and sinc interpolation. We focus on separable interpolation, so most of what is said applies to one-dimensional interpolation as well as N-dimensional separable interpolation.
Directivity of basic linear arrays
Bach, Henning
1970-01-01
For a linear uniform array ofnelements, an expression is derived for the directivity as a function of the spacing and the phase constants. The cases of isotropic elements, collinear short dipoles, and parallel short dipoles are included. The formula obtained is discussed in some detail and contour...
Data Compression with Linear Algebra
Etler, David
2015-01-01
A presentation on the applications of linear algebra to image compression. Covers entropy, the discrete cosine transform, thresholding, quantization, and examples of images compressed with DCT. Given in Spring 2015 at Ocean County College as part of the honors program.
175 Years of Linear Programming
polynomial-time solvability of linear programming, that is, testing if a polyhedron Q E ~ ... Q is rational, i.e. all extreme points and rays of Q are ra- tional vectors or ..... rithrll terminates with an interior solution, a post-processing step is usually ...
175 Years of Linear Programming
Home; Journals; Resonance – Journal of Science Education; Volume 4; Issue 10. 175 Years of Linear Programming - Max Flow = Min Cut. Vijay Chandru M R Rao. Series Article Volume 4 Issue 10 October 1999 pp 22-39. Fulltext. Click here to view fulltext PDF. Permanent link:
Linear collider systems and costs
Loew, G.A.
1993-05-01
The purpose of this paper is to examine some of the systems and sub-systems involved in so-called ''conventional'' e + e - linear colliders and to study how their design affects the overall cost of these machines. There are presently a total of at least six 500 GeV c. of m. linear collider projects under study in the world. Aside from TESLA (superconducting linac at 1.3 GHz) and CLIC (two-beam accelerator with main linac at 30GHz), the other four proposed e + e - linear colliders can be considered ''conventional'' in that their main linacs use the proven technique of driving room temperature accelerator sections with pulsed klystrons and modulators. The centrally distinguishing feature between these projects is their main linac rf frequency: 3 GHz for the DESY machine, 11.424 GHz for the SLAC and JLC machines, and 14 GHz for the VLEPP machine. The other systems, namely the electron and positron sources, preaccelerators, compressors, damping rings and final foci, are fairly similar from project to project. Probably more than 80% of the cost of these linear colliders will be incurred in the two main linacs facing each other and it is therefore in their design and construction that major savings or extra costs may be found
Linear accelerators of the future
Loew, G.A.
1986-07-01
Some of the requirements imposed on future linear accelerators to be used in electron-positron colliders are reviewed, as well as some approaches presently being examined for meeting those requirements. RF sources for use in these linacs are described, as well as wakefields, single bunches, and multiple-bunch trains
175 Years of Linear Programming
Home; Journals; Resonance – Journal of Science Education; Volume 4; Issue 5. 175 Years of Linear Programming - Pune's Gift. Vijay Chandru M R Rao. Series Article Volume 4 Issue 5 May ... Computer Science and Automation, IISc Bangalore 560012, India. Director, Indian Institute of Management, Bannerghatta Road, ...
Post-fire assessment of structural wood members
Robert J. Ross; Brian K. Brashaw; Xiping Wang; Robert H. White; Roy F. Pellerin
2005-01-01
Since the interior of a charred wood member normally retains its structural integrity, large structural wood members often do not need to be replaced after a fire. Engineering judgement is required to determine which members can remain and which members need to be replaced or repaired. Due to the lack of established methods to directly determine the residual capacity...
Suicidal behavior among members of Gamblers Anonymous.
Frank, M L; Lester, D; Wexler, A
1991-09-01
A national sample of 500 members of Gamblers Anonymous was surveyed by mail in order to gather information on suicidal history. One hundred sixty two usable surveys were returned representing 32.4% of the original sample. Compulsive gamblers who had a history of suicidal preoccupation began gambling at an earlier age than nonsuicidal gamblers and were more likely to have stolen to support their gambling. They also tended to have addicted relatives and children more than nonsuicidal gamblers did. The data suggest that those gamblers who had been suicidal tend to be more serious gamblers than nonsuicidal respondents.
Looking Backward, Looking Forward: MLA Members Speak
Alliston, April; Ammons, Elizabeth; Arnold, Jean; Baym, Nina; Beckett, Sandra L; Beidler, Peter G; Berger, Roger A; Bermann, Sandra; Wilson, J. J; Boone, Troy; Booth, Alison; Booth, Wayne C; Phelan, James; Borroff, Marie; Hassan, Ihab
2000-01-01
In 1997 I was asked to organize humanities outreach activities at the University of California, Irvine. The result was the formation of Humanities Out There (HOT). In our workshops, faculty members and graduate students supervise teams of undergraduates in order to take the methods and materials of the university into the larger community. I believe that programs like these will become increasingly important in the next century, as economic, cultural, and educational divisions deepe...
Members of the State Council of Geneva
Maximilien Brice
2002-01-01
Luncheon hosted by the Director-General for members of the State Council of Geneva: From left to right A. Naudi; J. May; M. Carlo Lamprecht, State Council - Employement, Foreign Office and Economic Departement; M. Robert Hensler, State Chancellor; L. Maiani, CERN Director General; H.F. Hoffmann; M. Robert Cramer, State Council - Environment, Agriculture and Interior Departement; J.Van Der Boon; M. Laurent Moutinot, State Council - Installation, equipment and housing Departement; C. Détraz; C. Wyss; P. Jenni; G. Hentsch; M. Pierre-François Unger, State Council - Health and Social Action Departement; G. Stassinakis; M. Bourquin, CERN Council President.
Cooperation with COMECON members in coke chemistry
Medricky. Z
1987-05-01
Discusses activities of the coking industry division of the standing committee for iron metallurgy of the COMECON. The following cooperation fields are analyzed: raw material basis for coking industry, coal charge preparation and methods for reducing proportion of coking coal in a coal charge (heat treatments, formed coke processes, partial briquetting, pelletizing, increasing coking temperature, packing etc.), coking technology, coke quenching, screening, chemical processing of coal gas, environmental protection in the coking industry, environmental effects of coking, pitch coke production, methods for increasing labor productivity. Research programs coordinated by member countries are reviewed. Programs in which Czechoslovakia participates are discussed.
BVA members wow judges in photo competition.
2016-09-03
Earlier this year, BVA ran its inaugural photo competition, giving members the opportunity to showcase the work of the veterinary profession and the animals and wildlife they encounter. Standing out from over 400 high-quality entries, judges picked the images reproduced in this month's BVA News as the winning and highly commended photos. To see all the entries and hear from the winners, visit www.bva.co.uk/vet-photos-2016/. There will be another photo competition in 2017 with more categories to be announced. British Veterinary Association.
Members of the Forum Engelberg visit CERN
Patrice Loïez
2002-01-01
The Forum Engelberg is an annual interdisciplinary conference held in Engelberg, Switzerland intended to act as an international platform for debate and exchange of views on key issues affecting scientific research, technology, economics and philosophy. Photo 01: Members of the Forum Engelberg and public figures from Geneva visit SM18, the test hall for LHC magnets: (left to right) N. Siegel, Prof. Dr. Med. Bernard Mach, Mr Alexander Höchli, H. Wenninger, Mrs Mireille Quirina, Mme Konrade Von Bremen, Mrs Thérèse Wolf, Prof. Roger Berthouzoz, Mrs Marie-Anne Heimo, Mr Bernard Ecoffey.
Members of the Forum Engelberg visit CERN
Patrice Loïez
2002-01-01
The Forum Engelberg is an annual interdisciplinary conference held in Engelberg, Switzerland intended to act as an international platform for debate and exchange of views on key issues affecting scientific research, technology, economics and philosophy. Its President is Hubert Curien - former French Minister of Research and Space Research, and President of the CERN Council from 1994 to 1996. Horst Wenninger (left) in animated discussion with Alexander Höchli, member of the Institutional Committee of Forum Engelberg and former Landammann of the canton of Obwalden.
Members of the Forum Engelberg visit CERN
Patrice Loïez
2002-01-01
The Forum Engelberg is an annual interdisciplinary conference held in Engelberg, Switzerland intended to act as an international platform for debate and exchange of views on key issues affecting scientific research, technology, economics and philosophy. Its President is Hubert Curien - former French Minister of Research and Space Research, and President of the CERN Council from 1994 to 1996. Photo 01: Thérèse Wolf, Secretary of Forum Engelberg; Alain Hervé; Horst Wenninger; and Alexander Höchli, Forum member and former Landammann of the canton of Obwalden, at the CMS detector's assembly site.
Czech Republic joins IPPOG as member
'marcelloni, claudia
2018-01-01
Czech Republic became an official IPPOG member on April 21 2018. The MOU between Czech Republic and IPPOG was previously signed by the director of the Institute of Physics of the Academy of Sciences of the Czech Republic. IPPOG chairs confirmed the agreement by signing the MOU during the meeting in Pisa in presence of IPPOG representative for Czech Republic dr. Vojtech Pleskot from the Faculty of Mathematics and Physics, Charles University in Prague. Dr. Vojtech Pleskot replaces Dr. Jiri Rames who did an excellent job during his long term work in the EPPOG and IPPOG.
Spaces of Piecewise Linear Manifolds
Gomez Lopez, Mauricio Esteban
Abstract In this thesis we introduce Δ-set ψPLd(RN) which we regard as the piecewise linear analogue of the space ψd(RN) of smooth d-dimensional submanifoldsin RN introduced by Galatius in [4]. Using ψPLd(RN) we define a bi-Δ-set Cd(RN)•,• ( whose geometric realization BCPLd(RN) = llCd(RN)•,•ll ......Abstract In this thesis we introduce Δ-set ψPLd(RN) which we regard as the piecewise linear analogue of the space ψd(RN) of smooth d-dimensional submanifoldsin RN introduced by Galatius in [4]. Using ψPLd(RN) we define a bi-Δ-set Cd(RN)•,• ( whose geometric realization BCPLd(RN) = ll...... BCPLd (RN) ≅ ΩN–1lψPLd (RN)•l when N — d ≥ 3. The proof of the main theorem relies on properties of ψPLd (RN) • which arise from the fact that this Δ-set can be obtained from a more general contravariant functor PL op → Sets defined on the category of finite dimensional polyhedraand piecewise linear...... maps, and on a fiberwise transversality result for piecewise linear submersions whose fibers are contained in R × (-1,1)N-1 ⊆ RN . For the proof of this transversality result we use a theorem of Hudson on extensions of piecewise linear isotopies which is why we need to include the condition N — d ≥ 3...
Linear fixed-field multipass arcs for recirculating linear accelerators
V. S. Morozov
2012-06-01
Full Text Available Recirculating linear accelerators (RLA’s provide a compact and efficient way of accelerating particle beams to medium and high energies by reusing the same linac for multiple passes. In the conventional scheme, after each pass, the different energy beams coming out of the linac are separated and directed into appropriate arcs for recirculation, with each pass requiring a separate fixed-energy arc. In this paper we present a concept of an RLA return arc based on linear combined-function magnets, in which two and potentially more consecutive passes with very different energies are transported through the same string of magnets. By adjusting the dipole and quadrupole components of the constituting linear combined-function magnets, the arc is designed to be achromatic and to have zero initial and final reference orbit offsets for all transported beam energies. We demonstrate the concept by developing a design for a droplet-shaped return arc for a dogbone RLA capable of transporting two beam passes with momenta different by a factor of 2. We present the results of tracking simulations of the two passes and lay out the path to end-to-end design and simulation of a complete dogbone RLA.
Reactor vessel supported by flexure member
Crawford, J.D.; Pankow, B.
1977-01-01
According to the present invention there is provided an improved arrangement for supporting a reactor vessel within a containment structure against static and dynamic vertical loadings capable of being imposed as a result of a serious accident as well as during periods of normal plant operation. The support arrangement of the invention is, at the same time, capable of accommodating radial displacements that normally occur between the reactor vessel and the containment structure due to operational transients. The arrangement comprises a plurality of vertical columns connected between the reactor vessel and a support base within the containment structure. The columns are designed to accommodate relative displacements between the vessel and the containment structure by flexing. This eliminates the need for relative sliding movements and thus enables the columns to be securely fixed to the vessel. This elimination of a provision for relative sliding movements avoids the spaces or gaps between the retention members and the retained elements as occurred in prior art arrangements and, concomitantly, the danger of establishing impact forces on the retention members in the event of an accident is reduced. (author)
The dying child and surviving family members.
Shrier, D K
1980-12-01
This overview of death and dying focuses on the dying child and surviving family members. Children's concepts of death at different developmental stages are reviewed. These range from an inability to distinguish death from other forms of separation prior to age 3, through partial concepts of death until, by age 10 to 15 years, children are able to conceptualize death as universal, inevitable and final. The importance of adults assisting in the child's growing comprehension of death is stressed. The stages of grief and mourning, as outlined by Kubler-Ross, are reviewed from the perspective of the child and family: denial, anger, bargaining, depression and acceptance. Recognition is given to the variations in coping styles among different family members. The special circumstances related to the death of an infant and the impact of the death of a child on the surviving siblings are discussed. Specific helpful interventions to assist families in coping with mourning are described. The death of a child remains one of the most painful and difficult events for a family and its physician to accept.
To all members of the personnel
2005-01-01
Temporary work for children of members of the personnel During the period mid-June to mid-September 2005, a limited number of vacancies for temporary work at CERN (normally unskilled work of a routine nature) will be available to children of members of the personnel (i.e. anyone holding an employment or association contract with CERN). It should be noted that candidates must be aged between 18 and 24 inclusive on the first day of the contract, and that they must have insurance cover for both illness and accident. In view of the limited number of vacancies available, no children having previously worked at CERN under this scheme can be considered. The duration of all appointments will be 4 weeks and the allowance for the period will be CHF 1621.- net. Candidates should apply via the HR Department's electronic recruitment system (E-rt) : http://humanresources.web.cern.ch/humanresources/internal/personnel/pmd/cr/Staff-kids-05.pdf Completed application forms must be returned to this Service by 8 April 2005 ...
To all members of the personnel
HR Department
2011-01-01
Summer work for children of members of the personnel During the period from 13 June to 16 September 2011 inclusive, there will be a limited number of jobs for summer work at CERN (normally unskilled work of a routine nature), which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with the Organization). Candidates must be aged between 18 and 24 inclusive on the first day of the contract, and must have insurance coverage for both illness and accident. The duration of all contracts will be 4 weeks and the allowance will be 1717 CHF for this period. Candidates should apply via the HR Department’s electronic recruitment system (E-rt): https://ert.cern.ch/browse_intranet/wd_pds?p_web_site_id=1&p_web_page_id=8886&p_no_apply=&p_show=N Completed application forms must be returned by 11 April 2011 at the latest. The results of the selection will be available by the end of May 2011. For further information, please con...
TO ALL MEMBERS OF THE PERSONNEL
2003-01-01
Temporary work for children of members of the personnel During the period mid-June to mid-September 2003, there will be a limited number of vacancies for temporary work at CERN (normally unskilled work of routine nature) which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with CERN). It should be noted that candidates must be aged between 18 and 24 inclusive on the first day of the contract, and that they must have insurance cover for both illness and accident. In view of the limited number of vacancies available, no children previously appointed at CERN under this scheme can be considered. The duration of all appointments will be 4 weeks, the allowance being CHF 1582.- for this period. Application form can be obtained from Martine PLAZA, HR Division (by using the slip in the bulletin or by electronic mail to Martine.Plaza@cern.ch) or at http://cern.ch/hr-web/internal/general/HN-personnel/ Completed application forms must be returne...
TO ALL MEMBERS OF THE PERSONNEL
2003-01-01
Temporary work for children of members of the personnel During the period mid-June to mid-September 2003, there will be a limited number of vacancies for temporary work at CERN (normally unskilled work of routine nature) which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with CERN). It should be noted that candidates must be aged between 18 and 24 inclusive on the first day of the contract, and that they must have insurance cover for both illness and accident. In view of the limited number of vacancies available, no children previously appointed at CERN under this scheme can be considered. The duration of all appointments will be 4 weeks, the allowance being CHF 1582.- for this period. Application form can be obtained from Martine PLAZA, HR Division (by electronic mail to Martine.Plaza@cern.ch) or at http://cern.ch/hr-web/internal/general/HN-personnel/ Completed application forms must be returned to this service by 2 May 2003 at th...
TO ALL MEMBERS OF THE PERSONNEL
2003-01-01
Temporary work for children of members of the personnel During the period mid-June to mid-September 2003, there will be a limited number of vacancies for temporary work at CERN (normally unskilled work of routine nature) which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with CERN). It should be noted that candidates must be aged between 18 and 24 inclusive on the first day of the contract, and that they must have insurance cover for both illness and accident. In view of the limited number of vacancies available, no children previously appointed at CERN under this scheme can be considered. The duration of all appointments will be 4 weeks, the allowance being CHF 1582.- for this period. Application form can be obtained from Martine PLAZA, HR Division (by electronic mail to Martine.Plaza@cern.ch) or at http://cern.ch/hr-web/internal/general/HN-personnel/ Completed application forms must be returned to this service by 2 May 2003 at t...
To all members of the personnel
HR Department
2009-01-01
Temporary work for children of members of the personnel During the period from 15 June to 11 September 2009 inclusive, there will be a limited number of jobs for temporary work at CERN (normally unskilled work of routine nature), which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with the Organization). Candidates must be aged between 18 and 24 inclusive on the first day of the contract, and must have insurance coverage for both illness and accident. The duration of all appointments will be 4 weeks and the allowance will be CHF 1717. - for this period. Candidates should apply via HR Department’s electronic recruitment system (E-rt): https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=6970 Completed application forms must be returned by 10 April 2009 at the latest. The results of the selection will be available on 22 May 2009. For further information, please contact: mailto:Inger.Carriero@cern.c...
To all members of the personnel
HR Department
2009-01-01
Temporary work for children of members of the personnel During the period from 15 June to 11 September 2009 inclusive, there will be a limited number of jobs for temporary work at CERN (normally unskilled work of a routine nature), which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with the Organization). Candidates must be aged between 18 and 24 inclusive on the first day of the contract, and must have insurance coverage for both illness and accident. The duration of all appointments will be 4 weeks and the allowance will be CHF 1717. - for this period. Candidates should apply via the HR Department’s electronic recruitment system (E-rt): https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=6970 Completed application forms must be returned by 10 April 2009 at the latest. The results of the selection will be available on 22 May 2009. For further information, please contact: mailto:Inger.Carriero@...
To all members of the personnel
HR Department
2008-01-01
Temporary work for children of members of the personnel During the period from 16 June to 12 September 2008 inclusive, there will be a limited number of jobs for temporary work at CERN (normally unskilled work of a routine nature), which will be open to children of members of the personnel (i.e. anyone holding an employment or association contract with the Organization). Candidates must be aged between 18 and 24 inclusive on the first day of the contract, and must have insurance coverage for both illness and accident. The duration of appointments will be 4 weeks and the allowance for this period will be 1663.- CHF. Candidates should apply via the HR Department’s electronic recruitment system (E-rt): https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=6160 Completed application forms must be made on-line by 13 April 2008 at the latest. The results of the selection will be available on 18 May 2008. For further information, please contact: Geraldine.Ballet@cern.ch HR ...
To all members of the personnel
2006-01-01
Temporary work for children of members of the personnelDuring the period 12 June to 15 September 2006 included, there will be a limited number of jobs for temporary work at CERN (normally unskilled work of routine nature) which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with CERN). It should be noted that candidates must be aged between 18 and 24 inclusive on the first day of the contract, and that they must have insurance cover for both illness and accident. In view of the limited number of jobs available, no children who have previously worked at CERN under this scheme can be considered. The duration of all appointments will be 4 weeks, the allowance being CHF 1640.- for this period. Candidates should apply via HR department's electronic recruitment system (E-rt): https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=4691 Completed application forms must be returned to this service by 17 April 2006 at the latest. The results of t...
To all members of the personnel
HR Department
2008-01-01
Temporary work for children of members of the personnel During the period from 16 June to 12 September 2008 inclusive, there will be a limited number of jobs for temporary work at CERN (normally unskilled work of a routine nature), which will be open to children of members of the personnel (i.e. anyone holding an employment or association contract with the Organization). Candidates must be aged between 18 and 24 inclusive on the first day of the contract, and must have insurance coverage for both illness and accident. The duration of appointments will be 4 weeks and the allowance for this period will be 1663 CHF. Candidates should apply via the HR Department’s electronic recruitment system (E-rt): https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=6160 Completed application forms must be submitted on-line by 13 April 2008 at the latest. The results of the selection will be available on 18 May 2008. For further information, please contact: mailto:Geraldine.Ballet@cern....
To all members of the personnel
HR Department
2010-01-01
Summer work for children of members of the personnel During the period from 14 June to 17 September 2010 inclusive, a limited number of jobs for summer work at CERN (normally unskilled work of a routine nature) will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with the Organization). Candidates must be aged between 18 and 24 inclusive on the first day of the contract, and must have insurance coverage for both illness and accident. The duration of all contracts will be 4 weeks and the allowance will be 1717 CHF for this period. Candidates should apply via the HR Department’s electronic recruitment system (E-rt): https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=7716 Completed application forms must be returned by 9 April 2010 at the latest. The results of the selection will be available on 21 May 2010. For further information, please contact: Inger.Carriero@cern.ch Tel. 71372
To all members of the personnel
Martine Briant
2006-01-01
Temporary work for children of members of the personnelDuring the period 12 June to 15 September 2006 included, there will be a limited number of jobs for temporary work at CERN (normally unskilled work of routine nature) which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with CERN). It should be noted that candidates must be aged between 18 and 24 inclusive on the first day of the contract, and that they must have insurance cover for both illness and accident. In view of the limited number of jobs available, no children who have previously worked at CERN under this scheme can be considered. The duration of all appointments will be 4 weeks, the allowance being CHF 1640.- for this period. Candidates should apply via HR department's electronic recruitment system (E-rt) : https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=4691 Completed application forms must be returned to this service by 17 April 2006 at the latest. The results of ...
To all members of the personnel
FI Department
2008-01-01
Temporary work for children of members of the personnel During the period from 16 June to 12 September 2008 inclusive, there will be a limited number of jobs for temporary work at CERN (normally unskilled work of routine nature), which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with the Organization). Candidates must be aged between 18 and 24 inclusive on the first day of the contract, and must have insurance coverage for both illness and accident. The duration of appointments will be 4 weeks and the allowance for this period will be 1663.- CHF. Candidates should apply via HR Department’s electronic recruitment system (E-rt): https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=6160 Completed application forms must be made on-line by 13 April 2008 at the latest. The results of the selection will be available on 18 May 2008. For further information, please contact: mailto:Geraldine.Ballet@cer...
To all members of the personnel
HR Department
2009-01-01
Temporary work for children of members of the personnel During the period from 15 June to 11 September 2009 inclusive, there will be a limited number of jobs for temporary work at CERN (normally unskilled work of a routine nature), which will be made available to children of members of the personnel (i.e. anyone holding an employment or association contract with the Organization). Candidates must be aged between 18 and 24 inclusive on the first day of the contract, and must have insurance coverage for both illness and accident. The duration of all appointments will be 4 weeks and the allowance will be CHF 1717. - for this period. Candidates should apply via the HR Department’s electronic recruitment system (E-rt): https://ert.cern.ch/browse_www/wd_pds?p_web_page_id=6970 Completed application forms must be returned by 10 April 2009 at the latest. The results of the selection will be available on 22 May 2009. For further information, please contact: mailto:Inger.Carriero...
Transfer pricing rules in EU member states
Veronika Solilová
2010-01-01
Full Text Available One of the important area of international taxes is transfer pricing. Transfer price is a price set by a taxpayer when selling to, buying from, or sharing resources with a related (associated person. The transactions between these persons should be assessed at their arm’s length price in according the arm’s length principle – international accepted standard – as the price which would have been agreed between unrelated parties in free market conditions. This paper is focused on the tranfer pricing rules used in particular EU Member States so as if EU Member States apply the arm’s length principle, define the related persons, apply recommendations of the OECD Guidelines, use the transfer pricing methods, require TP Documentation, exercise specific transfer pricing audit or impose specific penalties and apply APAs. Transfer pricing rules should prevent taxpayers from shifting income to related person organized in tax havens or in countries where they enjoy some special tax benefit.
Multivariate covariance generalized linear models
Bonat, W. H.; Jørgensen, Bent
2016-01-01
are fitted by using an efficient Newton scoring algorithm based on quasi-likelihood and Pearson estimating functions, using only second-moment assumptions. This provides a unified approach to a wide variety of types of response variables and covariance structures, including multivariate extensions......We propose a general framework for non-normal multivariate data analysis called multivariate covariance generalized linear models, designed to handle multivariate response variables, along with a wide range of temporal and spatial correlation structures defined in terms of a covariance link...... function combined with a matrix linear predictor involving known matrices. The method is motivated by three data examples that are not easily handled by existing methods. The first example concerns multivariate count data, the second involves response variables of mixed types, combined with repeated...
Systems of Inhomogeneous Linear Equations
Scherer, Philipp O. J.
Many problems in physics and especially computational physics involve systems of linear equations which arise e.g. from linearization of a general nonlinear problem or from discretization of differential equations. If the dimension of the system is not too large standard methods like Gaussian elimination or QR decomposition are sufficient. Systems with a tridiagonal matrix are important for cubic spline interpolation and numerical second derivatives. They can be solved very efficiently with a specialized Gaussian elimination method. Practical applications often involve very large dimensions and require iterative methods. Convergence of Jacobi and Gauss-Seidel methods is slow and can be improved by relaxation or over-relaxation. An alternative for large systems is the method of conjugate gradients.
Linear accelerator for radioisotope production
Hansborough, L.D.; Hamm, R.W.; Stovall, J.E.
1982-02-01
A 200- to 500-μA source of 70- to 90-MeV protons would be a valuable asset to the nuclear medicine program. A linear accelerator (linac) can achieve this performance, and it can be extended to even higher energies and currents. Variable energy and current options are available. A 70-MeV linac is described, based on recent innovations in linear accelerator technology; it would be 27.3 m long and cost approx. $6 million. By operating the radio-frequency (rf) power system at a level necessary to produce a 500-μA beam current, the cost of power deposited in the radioisotope-production target is comparable with existing cyclotrons. If the rf-power system is operated at full power, the same accelerator is capable of producing an 1140-μA beam, and the cost per beam watt on the target is less than half that of comparable cyclotrons
Linear regression in astronomy. II
Feigelson, Eric D.; Babu, Gutti J.
1992-01-01
A wide variety of least-squares linear regression procedures used in observational astronomy, particularly investigations of the cosmic distance scale, are presented and discussed. The classes of linear models considered are (1) unweighted regression lines, with bootstrap and jackknife resampling; (2) regression solutions when measurement error, in one or both variables, dominates the scatter; (3) methods to apply a calibration line to new data; (4) truncated regression models, which apply to flux-limited data sets; and (5) censored regression models, which apply when nondetections are present. For the calibration problem we develop two new procedures: a formula for the intercept offset between two parallel data sets, which propagates slope errors from one regression to the other; and a generalization of the Working-Hotelling confidence bands to nonstandard least-squares lines. They can provide improved error analysis for Faber-Jackson, Tully-Fisher, and similar cosmic distance scale relations.
Squares of Random Linear Codes
Cascudo Pueyo, Ignacio; Cramer, Ronald; Mirandola, Diego
2015-01-01
a positive answer, for codes of dimension $k$ and length roughly $\\frac{1}{2}k^2$ or smaller. Moreover, the convergence speed is exponential if the difference $k(k+1)/2-n$ is at least linear in $k$. The proof uses random coding and combinatorial arguments, together with algebraic tools involving the precise......Given a linear code $C$, one can define the $d$-th power of $C$ as the span of all componentwise products of $d$ elements of $C$. A power of $C$ may quickly fill the whole space. Our purpose is to answer the following question: does the square of a code ``typically'' fill the whole space? We give...
Linear inflation from quartic potential
Kannike, Kristjan; Racioppi, Antonio [National Institute of Chemical Physics and Biophysics,Rävala 10, 10143 Tallinn (Estonia); Raidal, Martti [National Institute of Chemical Physics and Biophysics,Rävala 10, 10143 Tallinn (Estonia); Institute of Physics, University of Tartu,Tartu (Estonia)
2016-01-07
We show that if the inflaton has a non-minimal coupling to gravity and the Planck scale is dynamically generated, the results of Coleman-Weinberg inflation are confined in between two attractor solutions: quadratic inflation, which is ruled out by the recent measurements, and linear inflation which, instead, is in the experimental allowed region. The minimal scenario has only one free parameter — the inflaton’s non-minimal coupling to gravity — that determines all physical parameters such as the tensor-to-scalar ratio and the reheating temperature of the Universe. Should the more precise future measurements of inflationary parameters point towards linear inflation, further interest in scale-invariant scenarios would be motivated.
Computational linear and commutative algebra
Kreuzer, Martin
2016-01-01
This book combines, in a novel and general way, an extensive development of the theory of families of commuting matrices with applications to zero-dimensional commutative rings, primary decompositions and polynomial system solving. It integrates the Linear Algebra of the Third Millennium, developed exclusively here, with classical algorithmic and algebraic techniques. Even the experienced reader will be pleasantly surprised to discover new and unexpected aspects in a variety of subjects including eigenvalues and eigenspaces of linear maps, joint eigenspaces of commuting families of endomorphisms, multiplication maps of zero-dimensional affine algebras, computation of primary decompositions and maximal ideals, and solution of polynomial systems. This book completes a trilogy initiated by the uncharacteristically witty books Computational Commutative Algebra 1 and 2 by the same authors. The material treated here is not available in book form, and much of it is not available at all. The authors continue to prese...
Perspectives on large linear colliders
Richter, B.
1987-11-01
Three main items in the design of large linear colliders are presented. The first is the interrelation of energy and luminosity requirements. These two items impose severe constraints on the accelerator builder who must design a machine to meet the needs of experimentl high energy physics rather than designing a machine for its own sake. An introduction is also given for linear collider design, concentrating on what goes on at the collision point, for still another constraint comes here from the beam-beam interaction which further restricts the choices available to the accelerator builder. The author also gives his impressions of the state of the technology available for building these kinds of machines within the next decade. The paper concludes with a brief recommendation for how we can all get on with the work faster, and hope to realize these machines sooner by working together. 10 refs., 9 figs
Forms and Linear Network Codes
Hansen, Johan P.
We present a general theory to obtain linear network codes utilizing forms and obtain explicit families of equidimensional vector spaces, in which any pair of distinct vector spaces intersect in the same small dimension. The theory is inspired by the methods of the author utilizing the osculating...... spaces of Veronese varieties. Linear network coding transmits information in terms of a basis of a vector space and the information is received as a basis of a possibly altered vector space. Ralf Koetter and Frank R. Kschischang introduced a metric on the set af vector spaces and showed that a minimal...... distance decoder for this metric achieves correct decoding if the dimension of the intersection of the transmitted and received vector space is sufficiently large. The vector spaces in our construction are equidistant in the above metric and the distance between any pair of vector spaces is large making...
Shu, Deming; Kearney, Steven P.; Preissner, Curt A.
2015-02-17
A method and deformation compensated flexural pivots structured for precision linear nanopositioning stages are provided. A deformation-compensated flexural linear guiding mechanism includes a basic parallel mechanism including a U-shaped member and a pair of parallel bars linked to respective pairs of I-link bars and each of the I-bars coupled by a respective pair of flexural pivots. The basic parallel mechanism includes substantially evenly distributed flexural pivots minimizing center shift dynamic errors.
Quadratic Blind Linear Unmixing: A Graphical User Interface for Tissue Characterization
Gutierrez-Navarro, O.; Campos-Delgado, D.U.; Arce-Santana, E. R.; Jo, Javier A.
2015-01-01
Spectral unmixing is the process of breaking down data from a sample into its basic components and their abundances. Previous work has been focused on blind unmixing of multi-spectral fluorescence lifetime imaging microscopy (m-FLIM) datasets under a linear mixture model and quadratic approximations. This method provides a fast linear decomposition and can work without a limitation in the maximum number of components or end-members. Hence this work presents an interactive software which imple...
Perspectives on large Linear Colliders
Richter, B.
1987-01-01
The accelerator community now generally agrees that the Linear Collider is the most cost-effective technology for reaching much higher energies in the center-of-mass than can be attained in the largest of the e + e - storage rings, LEP. Indeed, even as the first linear collider, the SLC at SLAC, is getting ready to begin operations groups, at SLAC, Novosibirsk, CERN and KEK are doing R and D and conceptual design studies on a next generation machine in the 1 TeV energy region. In this perspectives talk I do not want to restrict my comments to any particular design, and so I will talk about a high-energy machine as the NLC, which is shorthand for the Next Linear Collider, and taken to mean a machine with a center-of-mass energy someplace in the 0.5 to 2 TeV energy range with sufficient luminosity to carry out a meaningful experimental program. I want to discuss three main items with you. The first is the interrelation of energy and luminosity requirements. These two items impose severe constraints on the accelerator builder. Next, I will give an introduction to linear collider design, concentrating on what goes on at the collision point, for still another constraint comes here from the beam-beam interaction which further restricts the choices available to the accelerator builder.Then, I want to give my impressions of the state of the technology available for building these kinds of machines within the next decade
Linear gate with prescaled window
Koch, J; Bissem, H H; Krause, H; Scobel, W [Hamburg Univ. (Germany, F.R.). 1. Inst. fuer Experimentalphysik
1978-07-15
An electronic circuit is described that combines the features of a linear gate, a single channel analyzer and a prescaler. It allows selection of a pulse height region between two adjustable thresholds and scales the intensity of the spectrum within this window down by a factor 2sup(N) (0<=N<=9), whereas the complementary part of the spectrum is transmitted without being affected.
Stanford Linear Collider magnet positioning
Wand, B.T.
1991-08-01
For the installation of the Stanford Linear Collider (SLC) the positioning and alignment of the beam line components was performed in several individual steps. In the following the general procedures for each step are outlined. The calculation of ideal coordinates for the magnets in the entire SLC will be discussed in detail. Special emphasis was given to the mathematical algorithms and geometry used in the programs to calculate these ideal positions. 35 refs., 21 figs
Order-constrained linear optimization.
Tidwell, Joe W; Dougherty, Michael R; Chrabaszcz, Jeffrey S; Thomas, Rick P
2017-11-01
Despite the fact that data and theories in the social, behavioural, and health sciences are often represented on an ordinal scale, there has been relatively little emphasis on modelling ordinal properties. The most common analytic framework used in psychological science is the general linear model, whose variants include ANOVA, MANOVA, and ordinary linear regression. While these methods are designed to provide the best fit to the metric properties of the data, they are not designed to maximally model ordinal properties. In this paper, we develop an order-constrained linear least-squares (OCLO) optimization algorithm that maximizes the linear least-squares fit to the data conditional on maximizing the ordinal fit based on Kendall's τ. The algorithm builds on the maximum rank correlation estimator (Han, 1987, Journal of Econometrics, 35, 303) and the general monotone model (Dougherty & Thomas, 2012, Psychological Review, 119, 321). Analyses of simulated data indicate that when modelling data that adhere to the assumptions of ordinary least squares, OCLO shows minimal bias, little increase in variance, and almost no loss in out-of-sample predictive accuracy. In contrast, under conditions in which data include a small number of extreme scores (fat-tailed distributions), OCLO shows less bias and variance, and substantially better out-of-sample predictive accuracy, even when the outliers are removed. We show that the advantages of OCLO over ordinary least squares in predicting new observations hold across a variety of scenarios in which researchers must decide to retain or eliminate extreme scores when fitting data. © 2017 The British Psychological Society.
Segmented rail linear induction motor
Cowan, Jr., Maynard; Marder, Barry M.
1996-01-01
A segmented rail linear induction motor has a segmented rail consisting of a plurality of nonferrous electrically conductive segments aligned along a guideway. The motor further includes a carriage including at least one pair of opposed coils fastened to the carriage for moving the carriage. A power source applies an electric current to the coils to induce currents in the conductive surfaces to repel the coils from adjacent edges of the conductive surfaces.
Linear polarization of BY Draconis
Koch, R.H.; Pfeiffer, R.J.
1976-01-01
Linear polarization measurements are reported in four bandpasses for the flare star BY Dra. The red polarization is intrinsically variable at a confidence level greater than 99 percent. On a time scale of many months, the variability is not phase-locked to either a rotational or a Keplerian ephemeris. The observations of the three other bandpasses are useful principally to indicate a polarization spectrum rising toward shorter wavelengths
Linear morphea with secondary mucinosis
Khandpur Sujay
2009-01-01
Full Text Available Secondary mucin deposition in the skin is a common feature of lupus erythematosus and dermatomyositis. In scleroderma, it occurs uncommonly or in small amount. We describe a 7-year-old boy with progressive, linear, bound-down plaques involving the thighs, lower abdomen and back with no systemic involvement. Histopathology showed features of scleroderma with abundant mucin deposition in the reticular dermis. This report highlights excessive mucin deposition in lesions of morphea.
Cast dielectric composite linear accelerator
Sanders, David M [Livermore, CA; Sampayan, Stephen [Manteca, CA; Slenes, Kirk [Albuquerque, NM; Stoller, H M [Albuquerque, NM
2009-11-10
A linear accelerator having cast dielectric composite layers integrally formed with conductor electrodes in a solventless fabrication process, with the cast dielectric composite preferably having a nanoparticle filler in an organic polymer such as a thermosetting resin. By incorporating this cast dielectric composite the dielectric constant of critical insulating layers of the transmission lines of the accelerator are increased while simultaneously maintaining high dielectric strengths for the accelerator.
Introduction to Microwave Linear [Accelerators
Whittum, David H
1999-01-04
The elements of microwave linear accelerators are introduced starting with the principles of acceleration and accelerating structures. Considerations for microwave structure modeling and design are developed from an elementary point of view. Basic elements of microwave electronics are described for application to the accelerator circuit and instrumentation. Concepts of beam physics are explored together with examples of common beamline instruments. Charged particle optics and lattice diagnostics are introduced. Considerations for fixed-target and colliding-beam experimentation are summarized.
Positive Quasi Linear Operator Formulation
Berry, L.A.; Jaeger, E.F.
2005-01-01
Expressions for the RF quasi-linear operator are biquadratic sums over the Fourier modes (or FLR equivalent) that describe the RF electric field with a kernel that is a function of the two wave vectors, k-vector L and k-vector R , in the sum. As a result of either an implicit or explicit average over field lines or flux surfaces, this kernel only depends on one parallel wave vector, conventionally k R -vector. When k-vector is an independent component of the representation for E, the sums are demonstrably positive. However, except for closed field line systems, k-vector is dependent on the local direction of the equilibrium magnetic field, and, empirically, the absorbed energy and quasi-linear diffusion coefficients are observed to have negative features. We have formally introduced an independent k-vector sum by Fourier transforming the RF electric field (assuming straight field lines) using a field-line-length coordinate. The resulting expression is positive. We have modeled this approach by calculating the quasi linear operator for 'modes' with fixed k-vector. We form these modes by discretizing k-vector and then assigning all of the Fourier components with k-vectorthat fall within a given k-vector bin to that k-vector mode. Results will be shown as a function of the number of bins. Future work will involve implementing the expressions derived from the Fourier transform and evaluating the dependence on field line length
BLAS- BASIC LINEAR ALGEBRA SUBPROGRAMS
Krogh, F. T.
1994-01-01
The Basic Linear Algebra Subprogram (BLAS) library is a collection of FORTRAN callable routines for employing standard techniques in performing the basic operations of numerical linear algebra. The BLAS library was developed to provide a portable and efficient source of basic operations for designers of programs involving linear algebraic computations. The subprograms available in the library cover the operations of dot product, multiplication of a scalar and a vector, vector plus a scalar times a vector, Givens transformation, modified Givens transformation, copy, swap, Euclidean norm, sum of magnitudes, and location of the largest magnitude element. Since these subprograms are to be used in an ANSI FORTRAN context, the cases of single precision, double precision, and complex data are provided for. All of the subprograms have been thoroughly tested and produce consistent results even when transported from machine to machine. BLAS contains Assembler versions and FORTRAN test code for any of the following compilers: Lahey F77L, Microsoft FORTRAN, or IBM Professional FORTRAN. It requires the Microsoft Macro Assembler and a math co-processor. The PC implementation allows individual arrays of over 64K. The BLAS library was developed in 1979. The PC version was made available in 1986 and updated in 1988.
Test accelerator for linear collider
Takeda, S.; Akai, K.; Akemoto, M.; Araki, S.; Hayano, H.; Hugo, T.; Ishihara, N.; Kawamoto, T.; Kimura, Y.; Kobayashi, H.; Kubo, T.; Kurokawa, S.; Matsumoto, H.; Mizuno, H.; Odagiri, J.; Otake, Y.; Sakai, H.; Shidara, T.; Shintake, T.; Suetake, M.; Takashima, T.; Takata, K.; Takeuchi, Y.; Urakawa, J.; Yamamoto, N.; Yokoya, K.; Yoshida, M.; Yoshioka, M.; Yamaoka, Y.
1989-01-01
KEK has proposed to build Test Accelerator Facility (TAF) capable of producing a 2.5 GeV electron beam for the purpose of stimulating R ampersand D for linear collider in TeV region. The TAF consists of a 1.5 GeV S-band linear accelerator, 1.5 GeV damping ring and 1.0 GeV X-band linear accelerator. The TAF project will be carried forward in three phases. Through Phase-I and Phase-II, the S-band and X-band linacs will be constructed, and in Phase-III, the damping ring will be completed. The construction of TAF Phase-I has started, and the 0.2 GeV S-band injector linac has been almost completed. The Phase-I linac is composed of a 240 keV electron gun, subharmonic bunchers, prebunchers and traveling buncher followed by high-gradient accelerating structures. The SLAC 5045 klystrons are driven at 450 kV in order to obtain the rf-power of 100 MW in a 1 μs pulse duration. The rf-power from a pair of klystrons are combined into an accelerating structure. The accelerating gradient up to 100 MeV/m will be obtained in a 0.6 m long structure. 5 refs., 3 figs., 2 tabs
Orthogonal sparse linear discriminant analysis
Liu, Zhonghua; Liu, Gang; Pu, Jiexin; Wang, Xiaohong; Wang, Haijun
2018-03-01
Linear discriminant analysis (LDA) is a linear feature extraction approach, and it has received much attention. On the basis of LDA, researchers have done a lot of research work on it, and many variant versions of LDA were proposed. However, the inherent problem of LDA cannot be solved very well by the variant methods. The major disadvantages of the classical LDA are as follows. First, it is sensitive to outliers and noises. Second, only the global discriminant structure is preserved, while the local discriminant information is ignored. In this paper, we present a new orthogonal sparse linear discriminant analysis (OSLDA) algorithm. The k nearest neighbour graph is first constructed to preserve the locality discriminant information of sample points. Then, L2,1-norm constraint on the projection matrix is used to act as loss function, which can make the proposed method robust to outliers in data points. Extensive experiments have been performed on several standard public image databases, and the experiment results demonstrate the performance of the proposed OSLDA algorithm.
Exercise habit formation in new gym members: a longitudinal study.
Kaushal, Navin; Rhodes, Ryan E
2015-08-01
Reasoned action approaches have primarily been applied to understand exercise behaviour for the past three decades, yet emerging findings in unconscious and Dual Process research show that behavior may also be predicted by automatic processes such as habit. The purpose of this study was to: (1) investigate the behavioral requirements for exercise habit formation, (2) how Dual Process approach predicts behaviour, and (3) what predicts habit by testing a model (Lally and Gardner in Health Psychol Rev 7:S137-S158, 2013). Participants (n = 111) were new gym members who completed surveys across 12 weeks. It was found that exercising for at least four bouts per week for 6 weeks was the minimum requirement to establish an exercise habit. Dual Process analysis using Linear Mixed Models (LMM) revealed habit and intention to be parallel predictors of exercise behavior in the trajectory analysis. Finally, the habit antecedent model in LLM showed that consistency (β = .21), low behavioral complexity (β = .19), environment (β = .17) and affective judgments (β = .13) all significantly (p < .05) predicted changes in habit formation over time. Trainers should keep exercises fun and simple for new clients and focus on consistency which could lead to habit formation in nearly 6 weeks.
Biomarkers of post-deployment resilience among military service members
Krista B. Highland
2015-01-01
Full Text Available The development of PTSD after military deployment is influenced by a combination of biopsychosocial risk and resilience factors. In particular, physiological factors may mark risk for symptom progression or resiliency. Research in civilian populations suggests elevated catecholamines after trauma are associated with PTSD months following the trauma. However, less is known regarding physiological markers of PTSD resilience among post-deployment service members (SM. We therefore assessed whether catecholamines obtained shortly after deployment were associated with combat-related PTSD symptoms three months later. Eighty-seven SMs completed the Clinician-Administered PTSD Scale for DSM-IV and blood draws within two months after return from deployment to Iraq or Afghanistan (“Time 1” or “T1” and three months later (“Time 2” or “T2”. Linear regression analyses demonstrated that lower norepinephrine at T1 was associated with lower PTSD symptoms at T2. In particular, T1 norepinephrine was positively associated with T2 symptom intensity and avoidance symptoms. The present findings represent a biologically-informed method of assessing PTSD resilience after deployment, which may aid clinicians in providing tailored treatments for those in the greatest need. Further research is needed to validate these findings and incorporate physiological measures within an assessment battery.
Core seismic behaviour: linear and non-linear models
Bernard, M.; Van Dorsselaere, M.; Gauvain, M.; Jenapierre-Gantenbein, M.
1981-08-01
The usual methodology for the core seismic behaviour analysis leads to a double complementary approach: to define a core model to be included in the reactor-block seismic response analysis, simple enough but representative of basic movements (diagrid or slab), to define a finer core model, with basic data issued from the first model. This paper presents the history of the different models of both kinds. The inert mass model (IMM) yielded a first rough diagrid movement. The direct linear model (DLM), without shocks and with sodium as an added mass, let to two different ones: DLM 1 with independent movements of the fuel and radial blanket subassemblies, and DLM 2 with a core combined movement. The non-linear (NLM) ''CORALIE'' uses the same basic modelization (Finite Element Beams) but accounts for shocks. It studies the response of a diameter on flats and takes into account the fluid coupling and the wrapper tube flexibility at the pad level. Damping consists of one modal part of 2% and one part due to shocks. Finally, ''CORALIE'' yields the time-history of the displacements and efforts on the supports, but damping (probably greater than 2%) and fluid-structures interaction are still to be precised. The validation experiments were performed on a RAPSODIE core mock-up on scale 1, in similitude of 1/3 as to SPX 1. The equivalent linear model (ELM) was developed for the SPX 1 reactor-block response analysis and a specified seismic level (SB or SM). It is composed of several oscillators fixed to the diagrid and yields the same maximum displacements and efforts than the NLM. The SPX 1 core seismic analysis with a diagrid input spectrum which corresponds to a 0,1 g group acceleration, has been carried out with these models: some aspects of these calculations are presented here
Grief elaboration in families with handicapped member.
Calandra, C; Finocchiaro, G; Raciti, L; Alberti, A
1992-01-01
Families with handicapped member seem to follow the same five stages (rejection and isolation, anger, dealing with the problem, depression, acceptance) of Kubler-Ross grief elaboration theory while dealing with the narcissistic wound of a handicapped child. Some of these families show a block in one of the stages. The effort of psychotherapy is to remove the block and let them reach the last stage. In this paper families under systemic psychotherapeutic treatment are analyzed, who had in common the birth of a child with low or modest invalidating signs and psychotic or autistic features. The families structure did not show the characteristics of a psychotic family. Nevertheless either one or both parents ignored the evidence of their child disease and they built a "disease-incongrous" wait around the child, trying to push away the painful reality. The authors explain the importance of this approach for the improvement of the autistic traits.
Members of the Forum Engelberg visit CERN
Patrice Loïez
2002-01-01
The Forum Engelberg is an annual interdisciplinary conference held in Engelberg, Switzerland intended to act as an international platform for debate and exchange of views on key issues affecting scientific research, technology, economics and philosophy. Its President is Hubert Curien - former French Minister of Research and Space Research, and President of the CERN Council from 1994 to 1996.Seated here at a presentation by Peter Jenni, spokesperson for the ATLAS collaboration, during the visit of Forum members and Geneva public figures are Bernard Ecoffey, Founder of the Forum Engelberg (left), and Jean-Claude Landry, Department of the Interior, Agriculture and Environment, state of Geneva. Photo 01: (left to right) Bernard Ecoffey, Jean-Claude Landry and Peter Jenni. Photos 02, 03: (left to right) Jean-Claude Landry, Bernard Ecoffey and Peter Jenni.
Migration from the new EU member countries
Pedersen, Louise Møller; Lund Thomsen, Trine
2012-01-01
investigates the potentials, limitations and conflicts of interests that are connected with temporary employment of Eastern European migrant workers within the unskilled labour sectors seen from the perspective of Danish labour market actors; politicians, labour marked unions, Danish employers, Danish......During the past four years more than 52.500 Eastern European EU citizens have worked and lived in Denmark. Migrant workers from the new EU countries are characterized by a high degree of mobility, flexibility and eagerness in terms of working and adapting to working conditions. Poorer socioeconomic...... and working conditions in their home countries as well as being of another cultural background than their Danish colleagues brings with it many challenges. This article examines the consequences of low-skilled labour migration to Denmark from the new EU member countries in Eastern Europe. The article...
Table of members of quasi-bands
Sakai, Mitsuo.
1984-04-01
The probable members of the quasi-bands in even-even nuclei for Z between 6 and 100 are listed in this table. The terms quasi-bands have been introduced in the so-called spherical regions as the counter parts of the collective bands in the deformed regions. In the present compilation, the data for deformed nuclei are classified for convenience under the same titles, Quasi-Ground Band, Quasi-Beta Band and Quasi-Gamma Band, as are used for other nuclear regions. The present edition covers the literature through September, 1983. Fifteen newly discovered nuclides are included. The classification of energy level into quasi-bands is made on the basis of the systematic trend in the data over large groups of nuclei. (Kato, T.)
Czech Republic to Become Member of ESO
2006-12-01
Today, an agreement was signed in Prague between ESO and the Czech Republic, aiming to make the latter become a full member of ESO as of 1 January 2007. "The future membership of the Czech Republic in ESO opens for the Czech astronomers completely new opportunities and possibilities. It will foster this discipline on the highest quality level and open new opportunities for Czech industry to actively cooperate in research and development of high-tech instruments for astronomical research," said Miroslava Kopicová, Minister of Education, Youth and Sports of the Czech Republic. ESO PR Photo 52/06 ESO PR Photo 52/06 Signing Ceremony "We warmly welcome the Czech Republic as the thirteenth member of ESO," said Catherine Cesarsky, ESO's Director General. "The timing couldn't be better chosen: with the Very Large Telescope, Europe is now at the forefront of ground-based astronomy, and with the construction of ALMA and the final studies for the European Extremely Large Telescope, we will ensure that this will remain so for several decades. We look forward to working together with our Czech colleagues towards these successes." The signing event took place at the Czech Ministry of Education, Youth and Sports in Prague. Following ratification by the Czech Parliament, the Czech Republic with thus join the twelve present member states of ESO, the European Organisation for Astronomical Research in the Southern Hemisphere: Belgium, Denmark, France, Finland, Germany, Italy, the Netherlands, Portugal, Spain, Sweden, Switzerland and the United Kingdom. The Czech Republic is the first country from Central and Eastern Europe to join ESO. Astronomy in the Czech Republic has a very long tradition that dates from as far back as 3500 BC. Four centuries ago, Tycho Brahe and Johannes Kepler established themselves in Prague at the invitation of the emperor Rudolph II, laying the ground for the first golden age in astronomy. Later, eminent scientists such as Christian Doppler, Ernst Mach and
Sensory loss amongst old family members
Rasmussen, Jon Dag; Winther, Ida Wentzel
2018-01-01
and their close family. Our tentative findings point towards a prominence of different insecurities and discomforts in social life that directly links to the decreased sensory abilities. Experiences of being ‘lost’, ‘set afloat’ and disconnected in everyday life interactions are broadly described by all...... on the old people suffering a decline in sensory abilities, but also on family members as individual loss becomes collective loss in the context of family and kinship. The paper presentation takes its point of departure in rough pieces of empirical material (e.g. film-clips, sound......-clips/montage and ethnographic description) and through exposition of tentative analysis and research findings we aim to initiate a discussion around central themes of the work....
(ReTranslating as Re-membering
Julie Tarif
2016-07-01
Full Text Available This paper explores how (retranslation – interlingual and intersemiotic – can be perceived as a way of both remembering the literary legacy of other cultures but also as a way of re-membering/re-generating the body of literature(s of the importing culture. It focuses on what is called “a classic” and anchors its reflexion in polysystem theory and in the metaphorical vision of literary works as an organic living body. To do so, it concentrates on the British literary classic Oliver Twist and its translations and adaptations into French. The article addresses the following questions: What is to be remembered of certain works? Why, how and by whom are those works remembered?
OSART Works to Help Member States
Kaiser, Peter
2013-01-01
Full text: Nuclear safety is a never ending pursuit for improvement, and one of the more prominent IAEA efforts that help Member States achieve higher levels of safety is the Operational Safety Review Team (OSART) programme. In OSART missions, the IAEA coordinates internationally-based teams of experts who conduct reviews of operational safety performance at nuclear power plants. The IAEA on 14 June 2013 marked the 30th anniversary of OSART. In 1983, the Agency conducted its first OSART mission to the Kori Nuclear Power Plant in the Republic of Korea, and it conducted a total of 174 OSART missions over the following 30 years. The reviews have been done in 34 nations at 103 nuclear sites. (author)
Members of the Forum Engelberg visit CERN
Patrice Loïez
2002-01-01
The Forum Engelberg is an annual interdisciplinary conference held in Engelberg, Switzerland intended to act as an international platform for debate and exchange of views on key issues affecting scientific research, technology, economics and philosophy. Its President is Hubert Curien - former French Minister of Research and Space Research, and President of the CERN Council from 1994 to 1996. Photo 01: Raymond Battistella - Director-General of SIG, Geneva's utilities provider (left) - and Bernard Ecoffey, Founder of the Forum Engelberg. In the background is the CMS magnet system under construction. The red concentric rings are part of the barrel yoke, which returns the magnetic flux generated by the superconducting coil. Supported from the innermost barrel ring is the outer cylinder of the vacuum tank that will house the superconducting coil. Photo 02: Alexander Höchli, member of the Institutional Committee of Forum Engelberg and former Landammann of the canton of Obwalden (left), with Raymond Battistella, Di...
Simple Planar Truss (Linear, Nonlinear and Stochastic Approach
Frydrýšek Karel
2016-11-01
Full Text Available This article deals with a simple planar and statically determinate pin-connected truss. It demonstrates the processes and methods of derivations and solutions according to 1st and 2nd order theories. The article applies linear and nonlinear approaches and their simplifications via a Maclaurin series. Programming connected with the stochastic Simulation-Based Reliability Method (i.e. the direct Monte Carlo approach is used to conduct a probabilistic reliability assessment (i.e. a calculation of the probability that plastic deformation will occur in members of the truss.
Mehdi Saberi-Firoozi
2009-02-01
Full Text Available Background and Purpose: Shiraz University of Medical Sciences as one of the oldest and largest universities of medicine in Iran with 50 years history has more than 450 faculty members and 5000 students. This study is an attempt to find out the level of job satisfaction among Shiraz University ofMedical Sciences’ faculty members.Methods: In midterm of 2003-2004, data on job satisfaction level among 404 faculty members from all schools of Shiraz University of Medical Sciences were collected. The translation of Spector’s job satisfaction score was used including 34 questions in 9 items of job satisfaction and each one based on Likert’s Scale with score an of 1-5. A question related to overall job satisfaction of faculty members was added.Results: Of all faculties,, 252 responded to the questionnaire and 70.1% expressed satisfaction in response the added question. The mean scores of job satisfaction in items of coworkers, work nature, supervision, management methods, academic relations, promotion, salary and suitable benefits were3.771, 3.265, 2.557, 2.454, 2.395, and 2.376 out of 5 respectively (F=223.8, p=0.0001. In the promotion item, the satisfaction of female faculty was lower than male subjects. The level of job satisfaction was not different between clinical faculty members of Medical School with or without private activity. The results of linear regression analysis between the items of job satisfaction revealed that reimbursement and fringe benefits could predict the overall job satisfaction (r2=0.70, p<0.01.Conclusion: As a whole, the faculty members of the university were satisfied with their jobs, but a correction in reimbursement, benefits and promotion regulations especially in lower academic ranks is needed to improve the level of job satisfaction in this group.Key words: JOB SATISFACTION, FACULTY MEMBER, BASIC AND CLINICAL DEPARTMENTS, FULLTIME, PART-TIME
Linnarsson, Josefin Rahmqvist; Benzein, Eva; Årestedt, Kristofer
2015-01-01
To describe Nurses' views of forensic care provided for victims of violence and their families in EDs, to identify factors associated with Nurses' attitudes towards families in care and to investigate if these attitudes were associated with the involvement of patients' families in care. Interpersonal violence has serious health consequences for individuals and family members. Emergency departments provide care for victims of violence, and nurses play a key role in forensic care. However, there is limited knowledge of their views and their involvement of family members. A cross-sectional design was used with a sample of all registered nurses (n = 867) in 28 emergency departments in Sweden. A self-report questionnaire, including the instrument Families' Importance in Nursing Care - Nurses' Attitudes, was used to collect data. Descriptive statistics, multiple linear regression and ordinal regression were used to analyse data. Four hundred and fifty-seven nurses completed the questionnaire (53%). Most nurses provided forensic care, but few had specific education for this task. Policy documents and routines existed for specific patient groups. Most nurses involved family members in care although education and policy documents rarely included them. Being a woman, policy documents and own experience of a critically ill family member were associated with a positive attitude towards family. A positive attitude towards family members was associated with involving patients' families in care. Many emergency department nurses provided forensic care without having specific education, and policy documents only concerned women and children. Nurses' positive attitude to family members was not reflected in policies or education. These results can inspire clinical forensic care interventions in emergency departments. Educational efforts for nurses and policies for all groups of victims of violence are needed. Emergency departments may need to rethink how family members are included
APPARATUS FOR NON-DESTRUCTIVE INSPECTION OF CANTILEVERED MEMBERS
Taylor, E.R.; Mahoney, C.H.; Lay, C.R.
1961-10-24
An apparatus for non-destructive inspection of cantilevered members, such as compressor blades, is described. The member under inspection is vibrated with a regulated source of air under pressure. The amplitude of vibration of the member is maintained at its natural frequency. The frequency of vibration of the member is measured. An indication of an excessive decay or erratic shifting in the measured frequency above an allowable hysteretic decay is provided as an indication of a fault in the member. The member is vibrated for a selected test period. (AEC)
Linear Time Local Approximation Algorithm for Maximum Stable Marriage
Zoltán Király
2013-08-01
Full Text Available We consider a two-sided market under incomplete preference lists with ties, where the goal is to find a maximum size stable matching. The problem is APX-hard, and a 3/2-approximation was given by McDermid [1]. This algorithm has a non-linear running time, and, more importantly needs global knowledge of all preference lists. We present a very natural, economically reasonable, local, linear time algorithm with the same ratio, using some ideas of Paluch [2]. In this algorithm every person make decisions using only their own list, and some information asked from members of these lists (as in the case of the famous algorithm of Gale and Shapley. Some consequences to the Hospitals/Residents problem are also discussed.
Perspectives and expectations of union member and non- union member teachers on teacher unions
Tuncer FİDAN
2015-12-01
Full Text Available Unions, which can be regarded as one of the constitutive elements of democracy, are the pressure groups in political and social fields. Unions were born out of industrial confrontations and expanded into the field of public services over time, and thus teachers – who are also public employees-, also obtained the right to establish and affiliate to unions. In this research the views of union member and non-union member teachers on the most important functions and operational effectiveness of unions, teachers’ expectations from unions and teachers’ evaluation of the solidarity, competition and cooperation between unions were determined and the perspectives of teachers on unionization were revealed. qualitative research design was used. The data needed were collected through semi-structured interviews from volunteering union member and non-union member teachers who were working in the primary and secondary schools in Ankara province and who were selected through “maximum variation sampling approach”. The data were then analyzed by using the content analysis technique. In conclusion, it was found that political ideology was the most important reason for membership of teachers’ unions. Protection and development of personal rights was found to be the most important function of teacher unions and unions were thought to be insufficient in performing those functions.
Palmer, S. B.; Wehmeyer, M. L.; Davies, D. K.; Stock, S. E.
2012-01-01
Background: A nationwide survey of family members of people with intellectual and developmental disabilities ranging in age from birth through adulthood was conducted to replicate a similar effort by Wehmeyer and update the knowledge base concerning technology use by people with intellectual and developmental disabilities. Method: Survey responses…
Inflation persistence: is it similar in the new EU member states and the euro area members?
Franta, Michal; Saxa, Branislav; Šmídková, K.
-, 25/2008 (2008), s. 1-35 Grant - others:Česká národní banka(CZ) B4/2003 Institutional research plan: CEZ:AV0Z70850503 Keywords : inflation persistence * new EU member states * new hybrid Phillips curve Subject RIV: AH - Economics http://ies.fsv.cuni.cz/default/file/download/id/9070
Inflation persistence in new EU member states: is it different than in the euro area members?
Franta, Michal; Saxa, Branislav; Šmídková, Kateřina
-, č. 10 (2007), s. 1-37 ISSN 1803-2397 Institutional research plan: CEZ:AV0Z70850503 Keywords : inflation persistence * new hybrid Phillips curve * new EU member states Subject RIV: AH - Economics http://www.cnb.cz/m2export/sites/www.cnb.cz/en/research/research_publications/cnb_wp/download/cnbwp_2007_10.pdf
A review of linear compressors for refrigeration
Liang, Kun
2017-01-01
Linear compressor has no crank mechanism compared with conventional reciprocating compressor. This allows higher efficiency, oil-free operation, lower cost and smaller size when linear compressors are used for vapour compression refrigeration (VCR) system. Typically, a linear compressor consists of a linear motor (connected to a piston) and suspension springs, operated at resonant frequency. This paper presents a review of linear compressors for refrigeration system. Different designs and mod...
A Trivial Linear Discriminant Function
Shuichi Shinmura
2015-11-01
Full Text Available In this paper, we focus on the new model selection procedure of the discriminant analysis. Combining re-sampling technique with k-fold cross validation, we develop a k-fold cross validation for small sample method. By this breakthrough, we obtain the mean error rate in the validation samples (M2 and the 95\\% confidence interval (CI of discriminant coefficient. Moreover, we propose the model selection procedure in which the model having a minimum M2 was chosen to the best model. We apply this new method and procedure to the pass/ fail determination of exam scores. In this case, we fix the constant =1 for seven linear discriminant functions (LDFs and several good results were obtained as follows: 1 M2 of Fisher's LDF are over 4.6\\% worse than Revised IP-OLDF. 2 A soft-margin SVM for penalty c=1 (SVM1 is worse than another mathematical programming (MP based LDFs and logistic regression . 3 The 95\\% CI of the best discriminant coefficients was obtained. Seven LDFs except for Fisher's LDF are almost the same as a trivial LDF for the linear separable model. Furthermore, if we choose the median of the coefficient of seven LDFs except for Fisher's LDF, those are almost the same as the trivial LDF for the linear separable model.
ESPRIT And Uniform Linear Arrays
Roy, R. H.; Goldburg, M.; Ottersten, B. E.; Swindlehurst, A. L.; Viberg, M.; Kailath, T.
1989-11-01
Abstract ¬â€?ESPRIT is a recently developed and patented technique for high-resolution estimation of signal parameters. It exploits an invariance structure designed into the sensor array to achieve a reduction in computational requirements of many orders of magnitude over previous techniques such as MUSIC, Burg's MEM, and Capon's ML, and in addition achieves performance improvement as measured by parameter estimate error variance. It is also manifestly more robust with respect to sensor errors (e.g. gain, phase, and location errors) than other methods as well. Whereas ESPRIT only requires that the sensor array possess a single invariance best visualized by considering two identical but other-wise arbitrary arrays of sensors displaced (but not rotated) with respect to each other, many arrays currently in use in various applications are uniform linear arrays of identical sensor elements. Phased array radars are commonplace in high-resolution direction finding systems, and uniform tapped delay lines (i.e., constant rate A/D converters) are the rule rather than the exception in digital signal processing systems. Such arrays possess many invariances, and are amenable to other types of analysis, which is one of the main reasons such structures are so prevalent. Recent developments in high-resolution algorithms of the signal/noise subspace genre including total least squares (TLS) ESPRIT applied to uniform linear arrays are summarized. ESPRIT is also shown to be a generalization of the root-MUSIC algorithm (applicable only to the case of uniform linear arrays of omni-directional sensors and unimodular cisoids). Comparisons with various estimator bounds, including CramerRao bounds, are presented.
Linearized gyro-kinetic equation
Catto, P.J.; Tsang, K.T.
1976-01-01
An ordering of the linearized Fokker-Planck equation is performed in which gyroradius corrections are retained to lowest order and the radial dependence appropriate for sheared magnetic fields is treated without resorting to a WKB technique. This description is shown to be necessary to obtain the proper radial dependence when the product of the poloidal wavenumber and the gyroradius is large (k rho much greater than 1). A like particle collision operator valid for arbitrary k rho also has been derived. In addition, neoclassical, drift, finite β (plasma pressure/magnetic pressure), and unperturbed toroidal electric field modifications are treated
Matrix algebra for linear models
Gruber, Marvin H J
2013-01-01
Matrix methods have evolved from a tool for expressing statistical problems to an indispensable part of the development, understanding, and use of various types of complex statistical analyses. This evolution has made matrix methods a vital part of statistical education. Traditionally, matrix methods are taught in courses on everything from regression analysis to stochastic processes, thus creating a fractured view of the topic. Matrix Algebra for Linear Models offers readers a unique, unified view of matrix analysis theory (where and when necessary), methods, and their applications. Written f
Fast feedback for linear colliders
Hendrickson, L.; Adolphsen, C.; Allison, S.; Gromme, T.; Grossberg, P.; Himel, T.; Krauter, K.; MacKenzie, R.; Minty, M.; Sass, R.
1995-01-01
A fast feedback system provides beam stabilization for the SLC. As the SLC is in some sense a prototype for future linear colliders, this system may be a prototype for future feedbacks. The SLC provides a good base of experience for feedback requirements and capabilities as well as a testing ground for performance characteristics. The feedback system controls a wide variety of machine parameters throughout the SLC and associated experiments, including regulation of beam position, angle, energy, intensity and timing parameters. The design and applications of the system are described, in addition to results of recent performance studies
Cosmological perturbations beyond linear order
CERN. Geneva
2013-01-01
Cosmological perturbation theory is the standard tool to understand the formation of the large scale structure in the Universe. However, its degree of applicability is limited by the growth of the amplitude of the matter perturbations with time. This problem can be tackled with by using N-body simulations or analytical techniques that go beyond the linear calculation. In my talk, I'll summarise some recent efforts in the latter that ameliorate the bad convergence of the standard perturbative expansion. The new techniques allow better analytical control on observables (as the matter power spectrum) over scales very relevant to understand the expansion history and formation of structure in the Universe.
PIGMI linear-accelerator technology
Boyd, T.J.; Crandall, K.R.; Hamm, R.W.
1981-01-01
A new linear-accelerator technology has been developed that makes pi-meson (pion) generation possible for cancer therapy in the setting of a major hospital center. This technology uses several new major inventions in particle accelerator science-such as a new accelerator system called the radio-frequency quadrupole (RFQ), and permanent-magnet drift-tube focusing-to substantially reduce the size, cost, and complexity of a meson factory for this use. This paper describes this technology, discusses other possible uses for these new developments, and finally discusses possible costs for such installations
Beam dynamics in linear colliders
Ruth, R.D.
1990-09-01
In this paper, we discuss some basic beam dynamics issues related to obtaining and preserving the luminosity of a next generation linear collider. The beams are extracted from a damping ring and compressed in length by the first bunch compressor. They are then accelerated in a preaccelerator linac up to an energy appropriate for injection into a high gradient linac. In many designs this pre-acceleration is followed by another bunch compression to reach a short bunch. After acceleration in the linac, the bunches are finally focused transversely to a small spot. 27 refs., 1 fig