Confined discharge plasma sources for Z-pinch experiments

International Nuclear Information System (INIS)

Hinshelwood, D.D.; Goodrich, P.J.; Mehlman, G.; Scherrer, V.E.; Stephanakis, S.J.; Young, F.C.

1989-01-01

The authors report their investigation Z-pinch implosions on the NRL Gamble II generator using metallic sources of sodium and aluminum, and non-metallic source of sodium (NaF), magnesium (MgF 2 ), and aluminum (Al 2 0 3 ). For 1 MA driving currents, peak Κ-shell radiated powers of about 100 GW and energies of about 1.5 kj have been obtained with both pure aluminum and NaF implosions. The aluminum results are comparable to those in previous Gamble II experiments with aluminum wire arrays. Confined discharge sources have been used to generate tens of GW in the Na Heα pump line and flourescence of the neon has been observed. The effects of nozzle shape and size, chamber diameter, amount of fuse material, and confined discharge current have been investigated in Gamble II implosion experiments. These studies indicate that confined discharge sources are capable of supplying significantly more material than required for implosions at the 1 MA level, so that this technique could be extended to higher current generators

Material testing in a linear theta pinch

International Nuclear Information System (INIS)

Alani, R.; Azodi, H.; Naraghi, M.; Safaii, B.; Torabi-Fard, A.

1983-01-01

The interaction of stainless steel 316 and Inconel 625 alloys has been investigated with a thermonuclear-like plasma, n = 10 16 cm -3 and Tsub(i) = 1 keV, generated in the Alvand I linear theta pinch. The average power flux is 10 7 W/cm 2 and the interaction time nearly one μs. A theoretical analysis based on the formation of an observed impurity layer near the material, has been used to determine the properties of the impurity layer and the extent of the damage on the material. Although arcing has been observed, the dominant damage mechanism has been assessed to be due to evaporation. Exposure to single shots has produced very heavily defective areas and even surface cracks on the SS 316 sample, but no cracks were observed on Inconel 625 after exposure to even 18 shots. On the basis of temperature rise and evaporation a comparison is made among materials exposed to plasmas of a theta pinch, shock tube, present generation tokamak and an anticipated tokamak reactor. (orig.)

Simulation of high-energy particle production through sausage and kink instabilities in pinched plasma discharges

International Nuclear Information System (INIS)

Haruki, Takayuki; Yousefi, Hamid Reza; Masugata, Katsumi; Sakai, Jun-Ichi; Mizuguchi, Yusuke; Makino, Nao; Ito, Hiroaki

2006-01-01

In an experimental plasma, high-energy particles were observed by using a plasma focus device, to obtain energies of a few hundred keV for electrons, up to MeV for ions. In order to study the mechanism of high-energy particle production in pinched plasma discharges, a numerical simulation was introduced. By use of a three-dimensional relativistic and fully electromagnetic particle-in-cell code, the dynamics of a Z-pinch plasma, thought to be unstable against sausage and kink instabilities, are investigated. In this work, the development of sausage and kink instabilities and subsequent high-energy particle production are shown. In the model used here, cylindrically distributed electrons and ions are driven by an external electric field. The driven particles spontaneously produce a current, which begins to pinch by the Lorentz force. Initially the pinched current is unstable against a sausage instability, and then becomes unstable against a kink instability. As a result high-energy particles are observed

Dense Z-pinch plasmas

International Nuclear Information System (INIS)

Shlachter, J.S.; Hammel, J.E.; Scudder, D.W.

1985-01-01

Early researchers recogniZed the desirable features of the linear Z-pinch configuration as a magnetic fusion scheme. In particular, a Z-pinch reactor might not require auxiliary heating or external field coils, and could constitute an uncomplicated, high plasma β geometry. The simple Z pinch, however, exhibited gross MHD instabilities that disrupted the plasma, and the linear Z pinch was abandoned in favor of more stable configurations. Recent advances in pulsed-power technology and an appreciation of the dynamic behavior of an ohmically heated Z pinch have led to a reexamination of the Z pinch as a workable fusion concept

Equilibrium, stability and heating of plasmas in linear and toroidal Extrap pinches

International Nuclear Information System (INIS)

Bonnevier, B.; Drake, J.R.; Dalhed, H.E.

1983-01-01

The Extrap scheme consists of a Z-pinch immersed in an octupole field. The total magnetic field has no component along the pinch axis. Globally stable Z-pinch equilibria with a distributed plasma current density and a duration of about 100 Alfven transit times have been observed in linear and toroidal sector experiments. Theoretical studies indicate that this stability can be the result of constraints introduced by the octupole field and the resulting separatrix of the total field, in combination with finite-Larmor-radius effects. A scheme for ICRF heating of the plasma in configurations with a magnetic neutral line, being applicable to Extrap and FRC, is analysed. Wave propagation arises owing to the Hall effect. Particle resonances are responsible for the absorption, owing to a high parallel wavenumber and a weak magnetic field. (author)

The quest for a z-pinch based fusion energy source—a historical perspective

Science.gov (United States)

Sethian, John

1997-05-01

Ever since 1958, when Oscar Anderson observed copious neutrons emanating from a "magnetically self-constricted column of deuterium plasma," scientists have attempted to develop the simple linear pinch into a fusion power source. After all, simple calculations show that if one can pass a current of slightly less than 2 million amperes through a stable D-T plasma, then one could achieve not just thermonuclear break-even, but thermonuclear gain. Moreover, several reactor studies have shown that a simple linear pinch could be the basis for a very attractive fusion system. The problem is, of course, that the seemingly simple act of passing 2 MA through a stable pinch has proven to be quite difficult to accomplish. The pinch tends to disrupt due to instabilities, either by the m=0 (sausage) or m=1 (kink) modes. Curtailing the growth of these instabilities has been the primary thrust of z-pinch fusion research, and over the years a wide variety of formation techniques have been tried. The early pinches were driven by relatively slow capacitive discharges and were formed by imploding a plasma column. The advent of fast pulsed power technology brought on a whole new repertoire of formation techniques, including: fast implosions, laser or field-enhanced breakdown in a uniform volume of gas, a discharge inside a small capillary, a frozen deuterium fiber isolated by vacuum, and staged concepts in which one pinch implodes upon another. And although none of these have yet to be successful, some have come tantalizingly close. This paper will review the history of this four-decade long quest for fusion power.

Linear pinch driven by a moving compact torus

International Nuclear Information System (INIS)

Hartman, C.W.; Hammer, J.H.; Eddleman, J.L.

1984-01-01

In principle, a Z-pinch of sufficiently large aspect ratio can provide arbitrarily high magnetic field intensity for the confinement of plasma. In practice, however, achievable field intensities and timescales are limited by parasitic inductances, pulse driver power, current, voltage, and voltage standoff of nearby insulating surfaces or surrounding gas. Further, instabilities may dominate to prevent high fields (kink mode) or enhance them (sausage mode) but in a nonuniform and uncontrollable way. In this paper we discuss an approach to producing a high-field-intensity pinch using a moving compact torus. The moving torus can serve as a very high power driver and may be used to compress a pre-established pinch field, switch on an accelerating pinch field, or may itself be reconfigured to form an intense pinch. In any case, the high energy, high energy density, and high velocity possible with an accelerated compact torus can provide extremely high power to overcome, by a number of orders of magnitude, the limitations to pinch formation described earlier. In this paper we will consider in detail pinches formed by reconfiguration of the compact torus

Pinch modes in the SPEED2 plasma focus

International Nuclear Information System (INIS)

Kies, W.; Decker, G.; Berntien, U.; Glushkov, D.A.; Sidelnikov, Yu.V.; Koshelev, K.N.; Simanovskij, D.M.; Bobashev, S.V.

2001-01-01

Deuterium discharges in the SPEED2 plasma focus (80 kJ, 200 kV, 2 MA, 400 ns) have been found unexpectedly stable within the operational regime as a neutron source. Only at higher filling pressures (above 6 mbar) sometimes m=0 instabilities appeared in the pinch column, especially in discharges of lower efficiency (moderate dynamics and neutron yield). Enhancing the electromagnetic radiation by doping these discharges with heavy gases (e.g. neon, argon) distinctly two pinch modes are produced, the micropinch mode (MPM) or the stable column mode (SCM), with a transition regime where the initial SCM is followed by the MPM. Micropinches are local radiative collapses initiated by m=0 instabilities of low-energy-density pinch plasmas. These instabilities and the successive micropinches can be suppressed by kinetic deuterons produced during dynamical compression of high-energy-density deuterium plasma sheaths. Depending on the relaxation of this fast deuteron component the pinch column can be stabilized for several tens of nanoseconds. While the short-lived (appr.1 ns) micropinches erratically appear as point-like successive flashes along the pinch axis with temperatures about 1 keV and about solid density the reproducible SCM, optimized with respect to the compression ratio, forms a powerful linear radiation source of temperatures and densities similar to the MPM. The SCM needs powerful (fast) drivers in order to use the kinetic ion stabilization, but not necessarily MA currents as available from the SPEED2 driver. This opens the possibility to establish the SCM also in compact experiments like SPEED3 (8 kJ, 80 kV, 0.8 MA, 300 ns) or even SPEED4 (2 kJ, 40 kV 250 kA, 300 ns). (author)

Rotational instability in a linear theta pinch

International Nuclear Information System (INIS)

Ekdahl, C.; Bartsch, R.R.; Commisso, R.J.; Gribble, R.F.; McKenna, K.F.; Miller, G.; Siemon, R.E.

1980-01-01

The m=1 ''wobble'' instability of the plasma column in a 5-m linear theta pinch has been studied using an axial array of orthogonally viewing position detectors to resolve the wavelength and frequency of the column motion. The experimental results are compared with recent theoretical predictions that include finite Larmor orbit effects. The frequency and wavelength characteristics at saturation agree with the predicted dispersion relation for a plasma rotating faster than the diamagnetic drift speed. Measurements of the magnetic fields at the ends of the pinch establish the existence of currents flowing in such a way that they short out the radial electric fields in the plasma column. The magnitude of rotation, the observed delay in the onset of m=1 motion, and the magnitude of end-shorting currents can all be understood in terms of the torsional Alfven waves that communicate to the central plasma column the information that the ends have been shorted. The same waves are responsible for the torque which rotates the plasma and leads to the observed m=1 instability. Observations of the plasma in the presence of solid end plugs indicate a stabilization of high-m number modes and a reduction of the m=1 amplitude

An investigation of transient pressure and plasma properties in a pinched plasma column. M.S. Thesis

Science.gov (United States)

Stover, E. K.; York, T. M.

1971-01-01

The transient pinched plasma column generated in a linear Z-pinch was studied experimentally and analytically. The plasma column was investigated experimentally with the following plasma diagnostics: a special rapid response pressure transducer, a magnetic field probe, a voltage probe and discharge luminosity. Axial pressure profiles on the discharge chamber axis were used to identify three characteristic regions of plasma column behavior; they were in temporal sequence: strong axial pressure asymmetry noted early in plasma column lifetime followed by plasma heating in which there is a rapid rise in static pressure and a slight decrease static pressure before plasma column breakup. Plasma column lifetime was approximately 5 microseconds. The axial pressure asymmetry was attributed to nonsimultaneous pinching of the imploding current sheet along the discharge chamber axis. The rapid heating is attributed in part to viscous effects introduced by radial gradients in the axial streaming velocity. Turbulent heating arising from discharge current excitation of the ion acoustic wave instability is also considered a possible heating mechanism.

Lasing at short wavelength in a capillary discharge and in a dense Z-pinch

International Nuclear Information System (INIS)

Kunze, H.-J.; Glenzer, S.; Steden, C.; Wieschebrink, H. T.; Koshelev, K. N.; Uskov, D.

1995-01-01

Results on the emission of the CVI Balmer-α transition obtained with a fast capillary discharge are summarized, and a model is discussed, which explains the observations as result of fast ions produced by a m=0 instabililty and charge exchange with CIII ions in the cold plasma region. Plasmas of large dimensions were produced in the gas-liner pinch discharge, and the emission of the 4f-3d transition has been studied in CIV, NV, OVI, and FVII. Amplification is seen on the transition in OVI and FVII

An investigation of transient pressures and plasma properties in a pinched plasma column. M.S. Thesis

Science.gov (United States)

Stover, E. K.; York, T. M.

1971-01-01

The transient pinched plasma column generated in a linear Z-pinch was studied experimentally and analytically. The plasma column was investigated experimentally with several plasma diagnostics; they were: a rapid response pressure transducer, a magnetic field probe, a voltage probe, and discharge luminosity. Axial pressure profiles on the discharge chamber axis were used to identify three characteristic regions of plasma column behavior: (1) strong axial pressure asymmetry noted early in plasma column lifetime, (2) followed by plasma heating in which there is a rapid rise in static pressure, and (3) a slight decrease static pressure before plasma column breakup. Plasma column lifetime was approximately 5 microseconds. The axial pressure asymmetry was attributed to nonsimultaneous pinching of the imploding current sheet along the discharge chamber axis. The rapid heating could be attributed in part to viscous effects introduced by radial gradients in the axial streaming velocity.

Kinetic description of linear theta-pinch equilibria

International Nuclear Information System (INIS)

Batchelor, D.B.; Davidson, R.C.

1975-01-01

Equilibrium properties of linear theta-pinch plasmas are studied within the framework of the steady-state (o/x=0) Vlasov-Maxwell equations. The analysis is carried out for an infinitely long plasma column aligned parallel to an externally applied axial magnetic field Bsub(z)sup(ext)esub(z). Equilibrium properties are calculated for the class of rigid-rotor Vlasov equilibria, in which the th component distribution function (Hsub(perpendicular), Psub(theta), upsilonsub(z) depends on perpendicular energy H and canonical angular momentum Psub(theta), exclusively through the linear combination Hsub(perpendicular)-ωsub(j)Psub(theta), where ω;=const.=angular velocity of mean rotation. General equilibrium relations that pertain to the entire class of rigid-rotor Vlasov equilibria are discussed; and specific examples of sharp- and diffuse-boundary equilibrium configurations are considered. Rigid-rotor density and magnetic field profiles are compared with experimentally observed profiles. A general prescription is given for determining the functional dependence of the equilibrium distribution function on Hsub(perpendicular)-ωsub(j)Psub(theta) in circumstances, where the density profile or magnetic field profile is specified. (author)

Engineering and physics considerations for a linear theta-pinch hybrid reactor (LTPHR)

International Nuclear Information System (INIS)

Krakowski, R.A.; Miller, R.L.; Hagenson, R.L.

1976-01-01

A fusion-fission hybrid reactor based on pulsed, high-β, linear theta-pinch magnetic confinement is considered. A preliminary design which incorporates key physics, engineering and economic considerations is presented. An extensive presentation of the system energy balance is made, and this energy balance is evaluated parametrically. The feasibility of end-loss reduction is addressed

Fiber Z-pinch experiments and calculations in the finite Larmor radius regime

International Nuclear Information System (INIS)

Haines, M.G.; Dangor, A.E.; Coppins, M.

1996-01-01

The dense Z-pinch project at Imperial College is aimed at achieving radiative collapse to high density in a hydrogen plasma, and also to study plasmas close to controlled fusion conditions. To this end, the MAGPIE generator (2.4 MV, 1.25 Ω, and 200 ns) has been built and tested, and is now giving preliminary experimental data at 60% of full voltage for carbon and CD 2 fibers. These discharges are characterized by an initial radial expansion followed by the occurrence of m = 0 structures with transient X-ray emission from bright spots. Late in the discharge a disruption can occur, accompanied by hard X-ray emission from the anode due to an energetic electron beam and, in the case of CD 2 fibers, a neutron burst. Concomitant theoretical studies have solved the linear stability problem for a Z-pinch with large ion Larmor radii, showing that a reduction in growth rate of m = 0 and m = 1 modes to about 20% of the magnetohydrodynamic (MHD) value can occur for a parabolic density profile when the Larmor radius is optimally 20% of the pinch radius. Two-dimensional MHD simulations of Z-pinches in two extremes of focussed short-pulse laser-plasma interactions and of galactic jets reveal a nonlinear stabilizing effect in the presence of sheared flow. One-dimensional simulations show that at low line density the lower hybrid drift instability can lead to coronal radial expansion of a Z-pinch plasma. (Author)

Fabrication of a segmented composite stainless steel-alumina discharge tube for a theta-pinch coil

International Nuclear Information System (INIS)

Dickinson, J.M.; Stoddard, S.D.; Muller, J.F.

1975-11-01

An 80-mm-diam segmented discharge tube that simulated in a simplified way the blanket and first wall of the Reference Theta-Pinch Reactor (RTPR) has been constructed. The segments were fabricated by plasma-arc spraying an alumina coating on tubular stainless steel trapezoids. These were laid up to form a cylinder that was contained in a fully dense alumina vacuum tube. The fabrication processes are discussed in detail

Effects of boundary conditions on temperature and density in an EXTRAP Z-pinch

International Nuclear Information System (INIS)

Drake, J.R.; Karlsson, P.

1985-08-01

Using the fluid equations, we examine transport in an Extrap configuration by carrying out calculations incorporating model profiles for the density and temperature. The goal of this analysis is to examine the scaling of the pinch equilibrium plasma density, temperature and radius with parameters that are characteristic for Extrap Z-pinches. These parameters include the discharge current, the neutral hydrogen filling density, an oxygen impurity fractional concentration and the condition at the pinch boundary. An Extrap Z-pinch is a pinch discharge where the current channel has a characteristic non-circular cross-section achieved by bounding the discharge by a magnetic separatrix produced when a vacuum octupole magnetic field, generated by currents in external conductors, combines with the self-magnetic field produced by the discharge current. The pinch boundary is changed from a plasma-vacuum boundary to an interface between a high-beta pinch plasma and a low-beta plasma contained in the vacuum magnetic field. The energy that is lost from the pinch region sustains this boundary layer. The introduction of a separatrix boundary around the pinch with four X-point nulls deteriorates the containment of the pinch somewhat. However the presence of the warm, low-beta plasma scrape-off layer, which provides a boundary condition on the pinch, tends to counteract the negative effects of the poorer confinement. Thus the equilibrium parameters that characterize the pinch may not be severely deteriorated by the introduction of the separatrix when the entire configuration, including the scrape-off layer, is considered. (author)

Plasma-erosion-enhanced neutron emission in fiber-generated dense Z-pinches

International Nuclear Information System (INIS)

Mosher, D.; Colombant, D.

1990-01-01

Experiments in which dense z-pinches are created from high-current discharges through frozen deuterium fibers have reported neutron yields far in excess of those expected from thermal processes. A simple analysis based on pinch collapse due to the sausage instability has successfully predicted the relative variation of neutron yield with discharge current, but model assumptions precluded prediction of absolute values of the yield. A pinch-collapse model derived from a 2-dimensional, nonlinear treatment of the sausage instability, combined with space-charged-limited (SCL) ion orbital dynamic for the vacuum region above the pinches and between the expanding flares, leads to neutron yields four or more orders-of-magnitude below experimental values. Here, the same pinch-collapse model is used in conjunction with a low-density plasma background above the collapsing pinches. Ions are accelerated across the space-charge sheath separating the background plasma from the flares, which electron emission from the flares is strongly insulated by the z-discharge magnetic field. The sheath gap increases in time, i.e., the background plasma erodes, at a rate determined by its density and the SCL ion current density which, in turn, depends on the z-discharge dynamics and the associated induced electromagnetic fields. A model incorporating the above processes is used to determine the accelerated ion energy spectrum and associated neutron yield as functions of the discharge, instability, and background parameters

Experiments on screw-pinch plasmas with elongated cross section

International Nuclear Information System (INIS)

Lassing, H.W.

1989-01-01

In this thesis experiments are described carried out with SPICA II, a toroidal screw-pinch plasma device. this device is the last one in a series of plasma machines of the toroidal screw-pinch differing from its predecessor in its race-track shaped section. In devices of the type toroidal screw-pinch stable confinement is possible of plasmas with larger β values than in a tokamak discharge. In a pinch the plasma is screwed up, during the formation, in such a way that in a relatively small volume a plasma is formated with a high pressure. During the screwing up the plasma is heated by shock heating as well as adiabatic compression. With the modified snowplow model the density and temperature after the formation can be calculated, starting from the initial conditions. When all ions arrive into the plasma column, the density in the column is determined by the volume compression. First purpose of the experiments was to find a stable discharge. Subsequently discharges have been made with a high as possible β in order to investigate at which maximum β it is possible to confine screw-pinch plasmas stably. When these had been found, the nature and importance could be investigated of the processes following which the screw-pinch plasma looses its energy. (author), 75 res.; 95 figs.; 8 tabs

Plasma channel and Z-pinch dynamics for heavy ion transport

Energy Technology Data Exchange (ETDEWEB)

Ponce-Marquez, David [Univ. of California, Berkeley, CA (United States)

2002-01-01

A self stabilized, free standing, z-pinch plasma channel has been proposed to deliver the high intensity heavy ion beam from the end of a driver to the fuel target in a heavy ion inertial fusion power plant. The z-pinch relaxes emittance and energy spread requirements requiring a lower cost driver. A z-pinch transport would reduce the number of beam entry port holes to the target chamber from over a hundred to four as compared to neutralized ballistic focusing thus reducing the driver hardware exposure to neutron flux. Experiments where a double pulse discharge technique is used, z-pinch plasma channels with enhanced stability are achieved. Typical parameters are 7 kV pre-pulse discharge and 30 kV main bank discharge with 50 kA of channel current in a 7 torr background gas atmosphere. This work is an experimental study of these plasma channels examining the relevant physics necessary to understand and model such plasmas. Laser diagnostics measured the dynamical properties of neutrals and plasma. Schlieren and phase contrast techniques probe the pre-pulse gas dynamics and infrared interferometry and faraday effect polarimetry are used on the z-pinch to study its electron density and current distribution. Stability and repeatability of the z-pinch depend on the initial conditions set by the pre-pulse. Results show that the z-pinch channel is wall stabilized by an on-axis gas density depression created by the pre-pulse through hydrodynamic expansion where the ratio of the initial gas density to the final gas density is > 10/1. The low on-axis density favors avalanching along the desired path for the main bank discharge. Pinch time is around 2 s from the main bank discharge initiation with a FWHM of ~ 2 cm. Results also show that typical main bank discharge plasma densities reach 10¹⁷ cm^-3 peak on axis for a 30 kV, 7 torr gas nitrogen discharge. Current rise time is limited by the circuit-channel inductance with the highest contribution to the

Plasma and current structures in dynamical pinches

International Nuclear Information System (INIS)

Butov, I.Ya.; Matveev, Yu.V.

1981-01-01

Dynamics of plasma layers and current structure in aZ-pinch device has been experimentally investigated. It is found that shaping of a main current envelope is ended with its explosion-like expansion, the pinch decaying after compression to separated current filaments. It is also shown that filling of a region outside the pinch with plasma and currents alternating in directions occurs owing to interaction of current loops (inductions) formed in a magnetic piston during its compression with reflected shock wave. Current circulating in the loops sometimes exceeds 1.5-2 times the current of discharge circuit. The phenomena noted appear during development of superheat instability and can be realized, for example, in theta-pinches, plasma focuses, tokamaks. The experiments were carried out at the Dynamic Zeta-pinch device at an energy reserse of up to 15 kJ (V 0 =24 kV) in a capacitor bank. Half-period of the discharge current is 9 μs; Isub(max)=3.5x10sup(5) A. Back current guide surrounding a china chamber of 28 cm diameter and 50 cm length is made in the form of a hollow cylinder. Initial chamber vacuum is 10 -6 torr [ru

Staged theta pinch experiments

International Nuclear Information System (INIS)

Linford, R.K.; Downing, J.N.; Gribble, R.F.; Jacobson, A.R.; Platts, D.A.; Thomas, K.S.

1976-01-01

Two implosion heating circuits are being experimentally tested. The principal experiment in the program is the 4.5-m-long Staged Theta Pinch (STP). It uses two relatively low energy (50kJ and 100 kJ), high voltage (125 kV) capacitor banks to produce the theta pinch plasma inside the 20 cm i.d. quartz discharge tube. A lower voltage (50 kV), higher energy (750 kJ) capacitor bank is used to contain the plasma and provide a variable amount of adiabatic compression. Because the experiment produces a higher ratio of implosion heating to compressional heating than conventional theta pinches, it should be capable of producing high temperature plasmas with a much larger ratio of plasma radius to discharge tube radius than has been possible in the past. The Resonant Heating Experiment (RHX) in its initial configuration is the same as a 0.9-m-long section of the high voltage part of the STP experiment and all the plasma results here were obtained with the experiment in that configuration. Part of the implosion bank will be removed and a low inductance crowbar added to convert it to the resonant heating configuration. (U.K.)

Experimental studies of the MHD stability of non-circular Extrap Z-pinches

International Nuclear Information System (INIS)

Drake, J.R.

1985-01-01

Extrap Z-pinches, which can be sustained for many Alfven times, can be characterized as non-circular Z-pinch discharges bounded by a magnetic separatrix acting somewhat like a limiter. The magnetic separatrix is produced when a vacuum magnetic field, generated by currents in external conductors, combines with the self-magnetic field produced by the discharge current. The separatrix deforms the pinch cross-section and affects the equilibrium at the pinch boundary; both effects improve stability. Experiments have been performed which indicate that both effects are necessary for the successful generation of sustained Extrap discharges. In one experiment, the importance of the non-circularity of the cross-section was investigated. The deformation provided by the vacuum field can provide regions in the discharge where field lines have good curvature, which improves the stability of the configuration against internal modes. In configurations apparently lacking good curvature, discharges could not be sustained. In a second experiment, the dependence of the amplitude of global kink instabilities on the discharge current density profile were studied. The behaviour of the modes was consistent with that which would be expected for surface current-driven modes. (orig.)

Experimental studies of the MHD stability of non-circular extrap Z-pinches

International Nuclear Information System (INIS)

Drake, J.R.

1984-12-01

Extrap Z-pinches, which can be sustained for many Alfven times, can be characterized as non-circular Z-pinch discharges bounded by a magnetic separatrix acting somewhat like a limiter. The magnetic separatrix is produced when a vacuum magnetic field, generated by currents in external conductors, combines with the self-magnetic field produced by the discharge current. The separatrix deforms the pinch cross-section and affects the equilibrium at the pinch boundary; both effects improve stability. Experiments have been performed which indicate that both effects are necessary for the successful generation of sustained Extrap discharges. In one experiment, the importance of the non-circularity of the cross-section was investigated. The deformation provided by the vacuum field can provide regions in the discharge where field lines have good curvature, which improves the stability of the configuration against internal modes. In configurations apparently lacking good curvature, discharges could not be sustained. In a second experiment, the dependence of the amplitude of global kink instabilities on the discharge current density profile were studied. The behaviour of the modes was consistent with that which would be expected for surface current-driven modes. (Author)

Study of flow and loss processes at the ends of a linear theta pinch. Progress report, June 1, 1978--May 31, 1979

International Nuclear Information System (INIS)

York, T.M.; Klevans, E.H.

1979-02-01

Experimental and analytical studies of end loss from a linear theta pinch have been carried out. Analysis of reduced data on loss from a 25 cm long theta pinch has indicated: rotation at the end of pinch collapse, which appears to persist; ejection of the plasma in two modes, the first of which includes reversed, trapped fields; unique patterns of radial and axial variation of electron density in the end loss flow; substantial inaccuracies in plasma properties indicated by spectroscopy as compared to Thomson scattering. Studies of loss in a 50 cm long pinch with 50 eV, 2 x 10 16 cm -3 plasma are underway

Scaling the Shear-flow Stabilized Z-pinch to Reactor Conditions

Science.gov (United States)

McLean, H. S.; Schmidt, A.; Shumlak, U.; Nelson, B. A.; Golingo, R. P.; Cleveau, E.

2015-11-01

We present a conceptual design along with scaling calculations for a pulsed fusion reactor based on the shear-flow-stabilized Z-pinch device. Experiments performed on the ZaP device, at the University of Washington, have demonstrated stable operation for durations of 20 usec at ~100kA discharge current for pinches that are ~1 cm in diameter and 100 cm long. The inverse of the pinch diameter and plasma energy density scale strongly with pinch current and calculations show that maintaining stabilization durations of ~7 usec for increased discharge current (~15x) in a shortened pinch (10 cm) results in a pinch diameter of ~200 um and plasma conditions that approach those needed to support significant fusion burn and energy gain (Ti ~ 30keV, density ~ 3e26/m3, ntau ~1.4e20 sec/m3). Compelling features of the concept include operation at modest discharge current (1.5 MA) and voltage (40kV) along with direct adoption of liquid metals for at least one electrode--technological capabilities that have been proven in existing, commercial, pulse power devices such as large ignitrons. LLNL-ABS-674920. This work performed under the auspices of the U.S. Department of Energy ARPAe ALPHA Program by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Experimental study of ultra-low q discharges in the linear Extrap L1 device

International Nuclear Information System (INIS)

Brunsell, P.; Karlsson, Per.

1991-01-01

Linear pinch discharges with combined octupole and longitudinal magnetic fields are experimentally studied in the Extrap L1 device. Plasma currents are around I p =10 kA, plasma temperautres are up to T e =50 eV and plasma densities are of the order of n=5x10 21 m -3 . The plasma equilibria are in the ultra-low q (ULQ) regime corresponding to operation with plasma currents in excess of the Kruskal-Shafranov stability limit (q less than 1). The plasma current exhibits the typical time behaviour seen in toroidal ULQ experiments; the unstable setting up phase and the step-wise decay with current levels corresponding to q-values in windows between rational values. Longitudinal plasma current generated by radial plasma diffusion is seen, with amplitudes up to 30% of the externally driven current during the initial phase of the discharge. The effect of the octupole magnetic field on the ULQ confinement is investigated. The plasma temperature increases by more than a factor of two, for the optimum octupole rod current (I v =I p ), compared to the case without octupole field. A plasma current limitation for stable operation corresponding to q bigger than 1/2 is observed, excepts for low axial magnetic field strength. In the low axial field regime, the octupole field alone provides sufficient stabilization for operation with q less than 1/2. Plasma density and temperature both increase linearly with applied axial magnetic field. The density shows a strong, approximately exponential, dependence on discharge voltage. (au)

Upper pinch radius limit in EXTRAP

International Nuclear Information System (INIS)

Lehnert, B.

1989-12-01

A simple static equilibrium model of the Z-pinch is considered where a hot plasma core is surrounded by a cold-mantle (gas blanket). The pinch radius, defined as the radial extension of the fully ionized plasma core, is uniquely determined by the plasma particle. momentum and heat balance equations. In Extrap configurations an octupole field is introduced which imposes a magnetic separatrix on Z-pinch geometry. This makes the conditions for Extrap equilibrium 'overdetermined' when the characteristic pinch radium given by the plasma parameters tends to exceed the characteristic radius of the magnetic separatrix. In this case no conventional pinch equilibrium can exist, and part of the current which is forced into the plasma discharge by external sources must be channelled outside of the separatrix, i.e. into the surrounding support structure of the Extrap conductors and the vessel walls. A possibly existing bootstrap current in the plasma boundary layer is further expected to be 'scraped off' in this case. The present paper gives some illustrations of the marginal case of this upper pinch radius limit, in a state where the pinch current is antiparallel to the external rod currents which generate the octupole field. (authors)

Influence of the inner diameters of capillary on the Z-Pinch plasma of the capillary discharge soft X-ray laser

International Nuclear Information System (INIS)

Jiang, Shan; Zhao, Yong-peng; Cui, Huai-yu; Li, Lian-bo; Ding, Yu-jie; Zhang, Wen-hong; Li, Wei

2015-01-01

In this paper, the effects of inner diameters on the Z-pinch plasma of capillary discharge soft X-ray laser were investigated with the 3.2 mm and 4.0 mm inner diameter alumina capillaries. The intensities of the laser emitted from the 3.2 mm and 4.0 mm inner diameter alumina capillaries were measured under different initial pressures. To understand the underlying physics of the experimental measurements, the Z-pinch plasma simulations had been conducted with a one-dimensional cylindrical symmetry Lagrangian magneto-hydrodynamics (MHD) code. The parametric studies of Z-pinch plasma, such as the electron temperature, the electron density and the Ne-like Ar ion density, were performed with the MHD code. With the experimental and the simulated results, the discussions had been conducted on the Z-pinch plasma of Ne-like Ar 46.9 nm laser with the 3.2 mm and 4.0 mm inner diameter alumina capillaries. The analysis had been made on the difference of the gain coefficients under the optimum pressures with both capillaries. Then, the effects of inner diameters on the optimum pressure and the pressure domain were analyzed. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

X-ray backlighting of two-wire Z-pinch plasma using X-pinch

International Nuclear Information System (INIS)

Tong, Zhao; Xiao-Bing, Zou; Ran, Zhang; Xin-Xin, Wang

2010-01-01

Two 50-μm Mo wires in parallel used as a Z-pinch load are electrically exploded with a pulsed current rising to 275 kA in 125 ns and their explosion processes are backlighted using an X-pinch as an x-ray source. The backlighting images show clearly the processes similar to those occurring in the initial stages of a cylindrical wire-array Z-pinch, including the electric explosion of single wires characterised by the dense wire cores surrounded by a low-density coronal plasma, the expansion of the exploding wire, the sausage instability (m = 0) in the coronal plasma around each wire, the motion of the coronal plasma as well as the wire core toward the current centroid, the formation of the precursor plasma column with a twist structure something like that of higher mode instability, especially the kink instability (m = 1). (fluids, plasmas and electric discharges)

Determination of plasma Z-pinch effect by intrinsic stimulated emission

International Nuclear Information System (INIS)

Lue, J.T.; Liang, J.M.

1977-01-01

The plasma Z-pinch behavior has been observed in a relatively small-bore diameter tube and low bank voltage discharge system. The instant of the occurrence of the laser line at 4880 A coincides with the plasma pinch time calculated by using a one-fluid snow-plow model. A determination of plasma pinch parameters by measuring the intrinsic stimulated emission of the ions is described

Accurate approximation of the dispersion differential equation of ideal magnetohydrodynamics: The diffuse linear pinch

International Nuclear Information System (INIS)

Barnes, D.C.; Cayton, T.E.

1980-01-01

The ideal magnetohydrodynamic stability of the diffuse linear pinch is studied in the special case when the poloidal magnetic field component is small compared with the axial field component. A two-term approximation for growth rates is derived by straightforward asymptotic expansion in terms of a small parameter that is proportional to (B/sub theta//rB/sub z/). Evaluation of the second term in the expansion requires only a trivial amount of additional computation after the leading-order eigenvalue and eigenfunction are determined. For small, but finite, values of the expansion parameter the second term is found to be non-negligible compared with the leading term. The approximate solution is compared with exact solutions and the range of validity of the approximation is investigated. Implications of these results to a wide class of problems involving weakly unstable near theta-pinch configurations are discussed

Equilibrium poloidal field distributions in reversed-field-pinch toroidal discharges

International Nuclear Information System (INIS)

Baker, D.A.; Mann, L.W.; Schoenberg, K.F.

1982-04-01

A comparison between the analytic formulae of Shafranov for equilibrium in axisymmetric toroidal reversed field pinch (RFP) systems and fully toroidal numerical solutions of the Grad-Shafranov equation is presented as a function of poloidal beta, internal plasma inductance, and aspect ratio. The Shafranov formula for the equilibrium poloidal field distribution is accurate to within 5% for aspect ratios greater than 2, poloidal betas less than 50%, and for plasma current channels that exceed one-third of the minor toroidal radius. The analytic description for the center shift of the innermost flux surface that encloses the plasma current (the Shafranov shift) is accurate to within 15% for aspect ratios greater than 2 and poloidal betas below 50%, provided the shift does not exceed one-tenth of the minor conducting boundary radius. The behavior of the magnetic axis shift as a function of plasma parameters is included. The Shafranov formulae provide a convenient method for describing the equilibrium behavior of an RFP discharge. Examples illustrating the application of the analytic formulae to the Los Alamos ZT-40M RFP experiment are given

Equilibrium poloidal-field distributions in reversed-field-pinch toroidal discharges

International Nuclear Information System (INIS)

Baker, D.A.; Mann, L.W.; Schoenberg, K.F.

1983-01-01

A comparison between the approximate analytic formulae of Shafranov for equilibrium in axisymmetric toroidal systems and fully toroidal numerical solutions of the Grad-Shafranov equation for reversed-field-pinch (RFP) configurations is presented as a function of poloidal beta, internal plasma inductance, and aspect ratio. The Shafranov formula for the equilibrium poloidal-field distribution at the conducting shell that surrounds the plasma is accurate to within 5% for aspect ratios greater than 2, poloidal betas less than 50%, and for plasma current channels that exceed one third of the minor toroidal radius. The analytic description for the centre shift of the innermost flux surface that encloses the plasma current (the Shafranov shift) is accurate to within 15% for aspect ratios greater than 2 and poloidal betas below 50%, provided the shift does not exceed one tenth of the minor conducting boundary radius. The Shafranov formulae provide a convenient method for describing the gross equilibrium behaviour of an axisymmetric RFP discharge, as well as an effective tool for designing the poloidal-field systems of RFP experiments. (author)

A Reactor Development Scenario for the FUZE Shear-flow Stabilized Z-pinch

Science.gov (United States)

McLean, H. S.; Higginson, D. P.; Schmidt, A.; Tummel, K. K.; Shumlak, U.; Nelson, B. A.; Claveau, E. L.; Golingo, R. P.; Weber, T. R.

2016-10-01

We present a conceptual design, scaling calculations, and a development path for a pulsed fusion reactor based on the shear-flow-stabilized Z-pinch device. Experiments performed on the ZaP device have demonstrated stable operation for 40 us at 150 kA total discharge current (with 100 kA in the pinch) for pinches that are 1cm in diameter and 100 cm long. Scaling calculations show that achieving stabilization for a pulse of 100 usec, for discharge current 1.5 MA, in a shortened pinch 50 cm, results in a pinch diameter of 200 um and a reactor plant Q 5 for reasonable assumptions of the various system efficiencies. We propose several key intermediate performance levels in order to justify further development. These include achieving operation at pinch currents of 300 kA, where Te and Ti are calculated to exceed 1 keV, 700 kA where fusion power exceeds pinch input power, and 1 MA where fusion energy per pulse exceeds input energy per pulse. This work funded by USDOE ARPAe ALPHA Program and performed under the auspices of Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-697801.

Inter-Diffusion of Plasma and Magnetic Fields in Pinch and Hardcore Discharges; Interdiffusion d'un Plasma et de Champs Magnetiques dans la Striction Rectiligne et la Striction Tubulaire; Vzaimnaya diffuziya plazmy i magnitnogo polya v pinch-razryadakh i razryadakh v tverdoj serdtsevine; Interdifusion Plasma-Campo Magnetico en Descargas de Estriccion y de Nucleo Rigido

Energy Technology Data Exchange (ETDEWEB)

Reynolds, P.; Lees, D. J.; Bickerton, R. J.; Hardcastle, R. A.; Wetherell, A. T.; White, B. M. [United Kingdom Atomic Energy Authority, Culham Laboratory, Abingdon, Berks. (United Kingdom)

1966-04-15

The inter-diffusion of plasma and magnetic field is studied in pinch and hardcore discharges in a large bore, linear discharge tube (TIBER). The variation with magnetic field configuration, initial pressure, peak current, pre-heat conditions and rise time is found. The rapid ('anomalous') field diffusion found in the pinch case is due to a hydromagnetic rather than an electrostatic instability. (author) [French] Les auteurs etudient l'interdiffusion d'un plasma et de champs magnetiques dans la striction rectiligne et la striction tubulaire, au moyen d'une chambre a decharge droite de grand diametre (TIBER). Ils en determinent les variations selon la configuration du champ magnetique, la pression initiale, le courant maximum, les conditions de preechauffage et le temps de montee. La diffusion du champ rapide (anormale) constatee dans le cas de la striction rectiligne s'explique par une instabilite hydromagnetique et non par une instabilite electrostatique. (author) [Spanish] Se estudia la interdifusion plasma-campo magnetico en descargas de estriccion y de nucleo rigido utilizando una camara lineal de descarga de gran diametro interno (TIBER). Se determina la variacion segun la configuracion del campo magnetico, la presion inicial, la intensidad maxima de corriente, las condiciones de precalentamiento y el tiempo de crecimiento. La rapida difusion de los campos ('difusion anomala') observada en el caso de la estriccion se debe mas a una inestabilidad hidromagnetica que a una electrostatica. (author) [Russian] Vzaimnaja diffuzija plazmy i magnitnogo polja issleduetsja v pinch-razrjadah i razrjadah v tverdoj serdcevine v linejnoj razrjadnoj trubke bol'shogo diametra (Tiber). Opredeljajutsja izmenenie konfiguracii magnitnogo polja, nachal'noe davlenie, pikovyj tok, uslovija predvaritel'nogo nagreva i vremja pod'ema. Pokazyvaetsja, chto bystraja (''anomal'naja'') diffuzija polja, ustanovlennaja pri pinche, imeet mesto skoree iz-za gidromagnitnoj, chem iz

Z-Pinch at extreme energies: Nanofocus of less than 1J. Plasma Focus of 400 J. Gas embedded Z-pinch operating at MA

International Nuclear Information System (INIS)

Pavez Morales, Cristian A

2007-01-01

The work presented in this thesis is in relation with an experimental study developed in three different pulsed plasma generators. Two of them were already operating in the plasma laboratory of the Chilean Nuclear Energy Commission (CCHEN ) at the beginning of this thesis and they are: a) plasma focus PF-40OJ ((880nF, 30kV, 120kA, 400J, 300ns maximum current, dl/dt4x10 11 A/s) which is one of the first plasma focus devices at low energy that produces neutron pulses of fusion and b) the pulsed power generator SPEED-2 (4.1μF equivalent capacity, 300 kV, 4 MA in short circuit, 187 kJ, 400 ns at maximum current, dl/dt∼10 13 A/s) designed to operate in a plasma focus configuration. The third experiment corresponds to a plasma focus device at energy lower than 1J (Nanofocus), which was designed, constructed and characterized during the development of this thesis. The performed work can be summarized in two general aspects: the experimental study of the scaling in plasma focus devices at low energy and the development of a linear Z-pinch configuration using the SPEED-2 generator. In this last situation, a mechanism of preionization was developed in order to create a gas embedded Z-pinch discharge (Deuterium in the case of our experiment) that was conveniently coupled to the electrical characteristics of the generator. In every experiment, the plasma properties were studied (density, dynamics, size, radiation emission) and they reported the state of it. In the plasma focus device PF-40OJ, the electronic density was characterized for discharges in H 2 by using optical refractive techniques, measuring density values in the pinch ∼10 25 m -3 , similar to those reported in plasma focus devices at higher energies. The anisotropy was measured in the distribution of the intensity in the neutron emission for discharges in D 2 using track detector techniques CR-39. A distribution for the neutron flux characterized by an isotropic contribution of 57.5% and also by other

High-β, improved confinement reversed-field pinch plasmas at high density

International Nuclear Information System (INIS)

Wyman, M. D.; Chapman, B. E.; Ahn, J. W.; Almagri, A. F.; Anderson, J. K.; Den Hartog, D. J.; Ebrahimi, F.; Ennis, D. A.; Fiksel, G.; Gangadhara, S.; Goetz, J. A.; O'Connell, R.; Oliva, S. P.; Prager, S. C.; Reusch, J. A.; Sarff, J. S.; Stephens, H. D.; Bonomo, F.; Franz, P.; Brower, D. L.

2008-01-01

In Madison Symmetric Torus [Dexter et al., Fusion Technol. 19, 131 (1991)] discharges where improved confinement is brought about by modification of the current profile, pellet injection has quadrupled the density, reaching n e =4x10 19 m -3 . Without pellet injection, the achievable density in improved confinement discharges had been limited by edge-resonant tearing instability. With pellet injection, the total beta has been increased to 26%, and the energy confinement time is comparable to that at low density. Pressure-driven local interchange and global tearing are predicted to be linearly unstable. Interchange has not yet been observed experimentally, but there is possible evidence of pressure-driven tearing, an instability usually driven by the current gradient in the reversed-field pinch

Determining the resistance of X-pinch plasma

International Nuclear Information System (INIS)

Zhao Shen; Zhu Xin-Lei; Zhang Ran; Luo Hai-Yun; Zou Xiao-Bing; Wang Xin-Xin; Xue Chuang; Ning Cheng; Ding Ning; Shu Xiao-Jian

2013-01-01

The current and the voltage of an X-pinch were measured. The inductance of the X-pinch was assumed to be a constant and estimated by the calculation of the magnetic field based on the well-known Biot—Savart's Law. The voltage of the inductance was calculated with L · di/dt and subtracted from the measured voltage of the X-pinch. Then, the resistance of the X-pinch was determined and the following results were obtained. At the start of the current flow the resistance of the exploding wires is several tens of Ohms, one order of magnitude, higher than the metallic resistance of the wires at room temperature, and then it falls quickly to about 1 Ω, which reflects the physical processes occurring in the electrically exploding wires, i.e., a current transition from the highly resistive wire core to the highly conductive plasma. It was shown that the inductive contribution to the voltage of the X-pinch is less than the resistive contribution. For the wires we used, the wires' material and diameter have no strong influence on the resistance of the X-pinch, which may be explained by the fact that the current flows through the plasma rather than through the metallic wire itself. As a result, the current is almost equally divided between two parallel X-pinches even though the diameter and material of the wires used for these two X-pinches are significantly different. (physics of gases, plasmas, and electric discharges)

Spatially and temporally resolved EUV emissions from SATURN z-pinches

International Nuclear Information System (INIS)

Nash, T.J.; Breeze, S.; Mock, R.; Jobe, D.

1995-01-01

EUV emissions can be used to measure several z-pinch parameters. The authors have measured implosion velocity from Doppler splitting of lines and estimated electron temperature during run-in from the mean ionization state of line emissions. In an argon pinch they measure an electron temperature of 100 eV before stagnation. To date Doppler split lines have measured implosion velocities less than 40 cm/microsecond. They are presently attempting to measure magnetic field or load current from Zeeman splitting and it may be possible to measure electron density from a Stark-broadened line. Opacity and ion thermal broadening may also contribute to line width information. The spectrometer utilizes a variable line space grating to give a flat focal field. Spectral resolution with a 60 micron detector resolution is up to 3,000 and generally increases with wavelength. This is sufficient to detect several plasma line broadening mechanisms. The spectrometer may detect lines above 100 angstrom and below 1,400 angstrom. Spectral range across a microchannel plate stripline detector decreases with increasing wavelength setting. The authors may gate two striplines with 1 to 12 nsec gates at any time during the pinch discharge. Each stripline spatially images the pinch diameter perpendicular to the direction of dispersion. Spatial resolution in the pinch diameter is 1 mm. Spatial acquisition along the z axis is also 1 mm. Data are presented from argon, krypton, and aluminum z-pinch discharges on the SATURN accelerator

Overview of the Fusion Z-Pinch Experiment FuZE

Science.gov (United States)

Weber, T. R.; Shumlak, U.; Nelson, B. A.; Golingo, R. P.; Claveau, E. L.; McLean, H. S.; Tummel, K. K.; Higginson, D. P.; Schmidt, A. E.; UW/LLNL Team

2016-10-01

Previously, the ZaP device, at the University of Washington, demonstrated sheared flow stabilized (SFS) Z-pinch plasmas. Instabilities that have historically plagued Z-pinch plasma confinement were mitigated using sheared flows generated from a coaxial plasma gun of the Marshall type. Based on these results, a new SFS Z-pinch experiment, the Fusion Z-pinch Experiment (FuZE), has been constructed. FuZE is designed to investigate the scaling of SFS Z-pinch plasmas towards fusion conditions. The experiment will be supported by high fidelity physics modeling using kinetic and fluid simulations. Initial plans are in place for a pulsed fusion reactor following the results of FuZE. Notably, the design relies on proven commercial technologies, including a modest discharge current (1.5 MA) and voltage (40 kV), and liquid metal electrodes. Supported by DoE FES, NNSA, and ARPA-E ALPHA.

Scylla IV-P theta pinch

International Nuclear Information System (INIS)

Bailey, A.G.; Chandler, G.I.; Ekdahl, C.A. Jr.; Lillberg, J.W.; Machalek, M.D.; Seibel, F.T.

1976-01-01

Scylla IV-P is a flexible, linear theta pinch designed to investigate high-density linear concepts, end-stoppering, alternate heating methods, and plasma injection techniques relevant to a pure fusion reactor and/or a fusion-fission hybrid system. The construction and experimental arrangement of the device are briefly described

Gas-puff Z-pinch experiment on the LIMAY-I

International Nuclear Information System (INIS)

Takasugi, K.; Miyamoto, T.; Akiyama, H.; Shimomura, N.; Sato, M.; Tazima, T.

1989-01-01

A gas-puff z-pinch plasma has been produced on the pulsed power generator LIMAY-I at IPP Nagoya University. The stored energy of the generator is 13 kJ, and it generates 600 kV-70 ns-3 Ω power pulse. Ar or He gas is puffed from a hollow nozzle with 18 mm diameter, and a z-pinch plasma is produced by a discharge between 3 mm gap electrodes

Reduction of thermal expansion in Z-pinches by electron beam assisted magnetic field generation

International Nuclear Information System (INIS)

Heikkinen, J.A.; Karttunen, S.J.

1989-01-01

Weak radial expansion of a Z-pinch plasma column during its strong initial ohmic heating phase is expected when the generation of a confining magnetic field is assisted by a correctly formed electron beam pulse. Appropriate one-dimensional magnetohydrodynamic equations are numerically solved, and the observed increase of plasma radius as a function of time for various discharge parameters is compared to a normal Z-pinch discharge initiation. (author)

Energy transfer efficiency measurements in a theta-pinch

International Nuclear Information System (INIS)

Cavalcanti, G.H.; Luna, F.R.T.; Trigueiros, A.G.

1993-01-01

An increase in energy transfer efficiency of the capacitor bank to the plasma was obtained when the electrical system of a theta-pinch was changed so that the ratio of total inductance to coil inductance was switched of 1/6 to 1/2. A further increase about 20% was obtained for 16/1 ratio. The measurements were made through the current discharge decay, and the spectral analysis of the emitted light from theta-pinch shows a correspondent efficiency increase. (author)

Cryogenic high current discharges

International Nuclear Information System (INIS)

Meierovich, B.E.

1994-01-01

Z-pinches formed from frozen deuterium fibers by a rapidly rising current have enhanced stability and high neutron yield. The efforts to understand the enhanced stability and neutron yield on the basis of classical picture of Bennett equilibrium of the current channel has not given satisfactory results. The traditional approach does not take into account the essential difference between the frozen deuterium fiber Z-pinches and the usual Z-pinches such as exploding wires or classical gas-puffed Z-pinches. The very low temperature of the fiber atoms (10 K), together with the rapidly rising current, result in the coexistence of a high current channel with unionized fiber atoms for a substantial period of time. This phenomena lasts during the risetime. This approach takes into account the difference of the breakdown in a dielectric deuterium fiber and the breakdown in a metallic wire. This difference is essential to the understanding of specific features of cryogenic high current discharges. Z-pinches in frozen deuterium fibers should be considered as a qualitatively new phenomenon on the boundary of cryogenic and high current physics. It is a start of a new branch in plasma physics: the physics of cryogenic high current discharges

Theory of neutron spectra from d-d-reactions in the linear z-pinch and the plasma focus

International Nuclear Information System (INIS)

Deutsch, R.; Kaeppeler, H.J.

1982-05-01

Because of a finite gyroradius effect, the equilibrium probability density function of the ions in the azimuthal magnetic field of a linear z-pinch becomes anisotropic. This density function was derived by solving the Vlasov equation and used to determine the neutron spectra produced in the deuterium plasma of a z-pinch. The neutron spectra were calculated for two models, differing in the energy distribution of the fast ions. A background plasma with 'slow' ions was also considered. The interactions of the fast ions with the slow ions and 'beam-beam' interactions between fast ions were considered. Typical spectra for arbitrary directions to the cylindrical axis are given. The anisotropy factors were calculated. Considering the influence of the azimuthal magnetic field on the equilibrium density function of the deuterons, the well known particularities of the neutron spectra are obtained without any of the contradictions typical of the traditional models. (orig.)

High-energy electron acceleration in the gas-puff Z-pinch plasma

Energy Technology Data Exchange (ETDEWEB)

Takasugi, Keiichi, E-mail: takasugi@phys.cst.nihon-u.ac.jp [Institute of Quantum Science, Nihon University, 1-8 Kanda-Surugadai, Chiyoda, Tokyo 101-8308 (Japan); Miyazaki, Takanori [Institute of Quantum Science, Nihon University, 1-8 Kanda-Surugadai, Chiyoda, Tokyo 101-8308, Japan and Dept. Innovation Systems Eng., Utsunomiya University, 7-1-2 Yoto, Utsunomiya, Tochigi 321-8585 (Japan); Nishio, Mineyuki [Anan National College of Technology, 265 Aoki, Minobayashi, Anan, Tokushima 774-0017 (Japan)

2014-12-15

The characteristics of hard x-ray generation were examined in the gas-puff z-pinch experiment. The experiment on reversing the voltage was conducted. In both of the positive and negative discharges, the x-ray was generated only from the anode surface, so it was considered that the electrons were accelerated by the induced electromagnetic force at the pinch time.

A summary of the Berkeley and Livermore pinch programs

Energy Technology Data Exchange (ETDEWEB)

Colgate, Stirling A [University of California Radiation Laboratory, Livermore, CA (United States)

1958-07-01

In order to progress toward practical thermonuclear devices, the principal objective must be to prolong containment times by improving the electrical conductivity of the plasma. Those pinch configurations which are grossly unstable are, of course, unsuitable for practical thermonuclear work. Therefore our purely dynamic experiments are conducted only to study basic shock heating and instability mechanisms. Our basic evaluation of progress in pinch-type experiments is the reduction of the dissipation rate of the magnetic fields. The present pessimistic viewpoint is that most of the pinch devices that depend upon high current density within the plasma are beset with an enhanced dissipation rate which is disastrous to pinch containment. This dissipation is derived either from an electron plasma current instability or from hydromagnetic turbulence. Both have been predicted in theory and observed in experiment. Studies have been presented for the following cases: linear and toroidal pinch experiments; sheet pinch devices of modest size; homopolar geometry; shock heating and screw dynamic pinch.

Investigation of plasma turbulence in a theta-pinch-discharge

International Nuclear Information System (INIS)

Lins, G.

1980-01-01

This thesis is concerned with investigations of plasma turbulence in a 3 KJ Theta-Pinch during implosion by high-frequency Stark-effect and Thomson scattering. The next points are modifications of electron-distribution function by ionization in low preionizized turbulent plasma and energy losses by particle flow and heat flow at the ends. (HT)

Evidence of flow stabilization in the ZaP Z pinch experiment

International Nuclear Information System (INIS)

Shumlak, U.; Crawford, E.; Golingo, R.P.; Nelson, B.A.; Zyrmpas, A.; Den Hartog, D.J.; Holly, D.J.

2001-01-01

The stabilizing effect of an axial flow on the m = 1 kink instability in Z pinches has been studied numerically with a linearized ideal MHD model to reveal that a sheared axial flow stabilizes the kink mode when the shear exceeds a threshold. The sheared flow stabilizing effect is investigated with the flow-through Z pinch experiment, ZaP. An azimuthal array of surface mounted magnetic probes located at the midplane of the 50 cm long pinch plasma measures the fluctuation levels of the azimuthal modes m=1, 2, and 3. After pinch formation a quiescent period is found where the mode activity is reduced to a few percent of the average field. Optical images from a fast framing camera and a HeNe interferometer also indicate a stable pinch plasma during this time. Doppler shift measurements of a C-III line correspond to an axial flow velocity of 9.6x10 4 m/s internal to the pinch. During the time when the axial plasma flow is high, the plasma experiences a quiescent period which lasts approximately 800 exponential growth times predicted by linear theory for a static plasma. (author)

Mechanism of hot spots formation in magnetic Z-pinch

Energy Technology Data Exchange (ETDEWEB)

Kubes, P; Kravarik, J [Ceske Vysoke Uceni Technicke, Prague (Czech Republic). Fakulta Elektrotechnicka; Kolacek, K; Krejci, A [Akademie Ved Ceske Republiky, Prague (Czech Republic). Ustav Fyziky Plazmatu; Paduch, M; Tomaszewski, K [Inst. of Plasma Physics and Laser Microfusion, Warsaw (Poland)

1997-12-31

The evolution of neon implosion of low energy discharge (4 kJ, 40 kV, 150 kA, 1.1 {mu}s) was studied using X-ray, schlieren and high speed electrooptical visible gated Quadro camera diagnostics. The geometry, the helical structure of pinched column, two steps of pinching and X-ray emission were studied. The diameters, electron density and temperature of the hot spots were determined. The hypothesis of axial component of magnetic field generation, of helical shape of magnetic and electric field lines, of the possibility of the release of magnetic energy and of the acceleration of the keV electrons and ions due to voltage induction during the second pinching of the column are discussed. (author). 3 figs., 5 refs.

New bifocal pinch experiment SPEED 3

International Nuclear Information System (INIS)

Raacke, J.; Berntien, U.; Decker, G.; Kies, W.; Roewekamp, P.

1996-01-01

The SPEED 3 compact plasma focus device will be used as a soft x-ray source for various practical applications. It exploits a bifocal configuration with a plane insulator, very short accelerator and a hollow inner electrode. The discharge is driven by eight parallel two-stage Marx modules, capable of delivering up to 1.25 MA of current with the rise time of 0.3 s. The key parts of the device, the plasma diagnostic systems used, and the processes in the discharge are described in the paper. Framing camera pictures of a typical discharge are shown for illustration. The results of preliminary experiments are discussed, dealing almost exclusively with the discharge inaction, sheath and pinch formation. (J.U.). 1 tab., 3 figs., 2 refs

New bifocal pinch experiment SPEED 3

Energy Technology Data Exchange (ETDEWEB)

Raacke, J; Berntien, U; Decker, G; Kies, W; Roewekamp, P [Heinrich-Heine-Univ., Duesseldorf (Germany). Inst. fuer Experimentalphysik

1997-12-31

The SPEED 3 compact plasma focus device will be used as a soft x-ray source for various practical applications. It exploits a bifocal configuration with a plane insulator, very short accelerator and a hollow inner electrode. The discharge is driven by eight parallel two-stage Marx modules, capable of delivering up to 1.25 MA of current with the rise time of 0.3 s. The key parts of the device, the plasma diagnostic systems used, and the processes in the discharge are described in the paper. Framing camera pictures of a typical discharge are shown for illustration. The results of preliminary experiments are discussed, dealing almost exclusively with the discharge inaction, sheath and pinch formation. (J.U.). 1 tab., 3 figs., 2 refs.

Experimental investigation of energy loss and end loss physics in a linear theta pinch. Scientific report 81-3

International Nuclear Information System (INIS)

Jacoby, B.A.

1981-01-01

The results of an experimental study of particle and thermal loss processes from a 50-cm long theta pinch are presented. The plasma was generated with a 40-mTorr fill of deuterium in a 3.81 cm radius discharge tube; 67% Z-preionization was followed by a main current discharge that produced a 23-kG peak magnetic field in 4.75 μsec. The electron density and temperature in the plasma column at the end of dynamic implosion were characterized by 1.0 x 10 16 cm -3 and 20 eV, respectively. This was followed by adiabatic compression which occurred with the particle and energy loss of interest. The diagnostics employed in this experiment were Thomson scattering, continuum radiation spectroscopy, local magnetic-field probes, local pressure probes, and diamagnetic loops. Axial temperature and density profiles were mapped from the coil into the end region

Plasma resistance behavior during the linear decay phase of RFPs in ETA BETA II

International Nuclear Information System (INIS)

Nalesso, G.F.

1982-01-01

In the aided-reversal mode RFP discharges produced in ETA BETA II, the plasma current is characterized by a linear decay phase, which follows an approximately exponential phase. During the same period the measured toroidal voltage is negative and initially increasing in absolute value (exponential phase) and then decreasing to almost zero during the linear phase before the current termination. The same behavior of the current has been observed in the quiescent phase in Zeta where a negative toroidal electric field was also observed. In this note we present a model that can explain the linear decay phase and fits with the experimental parameters and allows us to estimate the plasma resistance behavior during the linear phase of slow reversed field pinch discharges

Recent studies of Reversed-Field Pinch reactors

International Nuclear Information System (INIS)

Hagenson, R.L.; Krakowski, R.A.

1981-01-01

The reactor prognoses of a class of confinement scheme that relies primarily on self-fields induced by axial currents flowing within a plasma column are presented. The primary focus has been placed on the toroidal Reversed-Field Pinch (RFP). At the limit of very large current densities is the gas-embedded Dense Z-Pinch (DZP), a small-radius, linear device. Past conventional RFP reactor designs are reviewed. The extention of these conventional RFP reactors to DD advanced-fuel operation is described. The implications are summarized of operating higher-density, compact RFPs as reactors, wherein the current density rather than physical dimensions are scaled. Lastly, the application of very high current densities supported in a sub-millimeter linear current channel, as embodied in the DZP reactor, is reviewed

Experimental study of the initial plasma formation stage in a linear theta pinch of inverted field

International Nuclear Information System (INIS)

Casin, G.C.; Alvarez, Ricardo; Rojkind, R.H.; Rodrigo, A.B.

1986-01-01

The initial stage of the plasma formation was studied in a linear theta pinch. Experiments were made to determine the machine operating conditions for good shot-to-shot reproducibility. Spectroscopic measurements of electron density and of electron and ion temperature were made afterwards to characterize the plasma at different stages of its heating process. The results obtained indicate that shot-to-shot reproducibility is strongly influenced by the presence of impurities and by the plasma preionization technique used. Under proper operating conditions, excellent reproducibility was observed. The measured values of the plasma parameters are compatible with those determined for similar machines. (Author) [es

Resistive wall modes in the EXTRAP T2R reversed-field pinch

Science.gov (United States)

Brunsell, P. R.; Malmberg, J.-A.; Yadikin, D.; Cecconello, M.

2003-10-01

Resistive wall modes (RWM) in the reversed field pinch are studied and a detailed comparison of experimental growth rates and linear magnetohydrodynamic (MHD) theory is made. RWM growth rates are experimentally measured in the thin shell device EXTRAP T2R [P. R. Brunsell et al., Plasma Phys. Controlled Fusion 43, 1 (2001)]. Linear MHD calculations of RWM growth rates are based on experimental equilibria. Experimental and linear MHD RWM growth rate dependency on the equilibrium profiles is investigated experimentally by varying the pinch parameter Θ=Bθ(a)/ in the range Θ=1.5-1.8. Quantitative agreement between experimental and linear MHD growth rates is seen. The dominating RWMs are the internal on-axis modes (having the same helicity as the central equilibrium field). At high Θ, external nonresonant modes are also observed. For internal modes experimental growth rates decrease with Θ while for external modes, growth rates increase with Θ. The effect of RWMs on the reversed-field pinch plasma performance is discussed.

Pinched Nerve

Science.gov (United States)

... You are here Home » Disorders » All Disorders Pinched Nerve Information Page Pinched Nerve Information Page What research is being done? Within the NINDS research programs, pinched nerves are addressed primarily through studies associated with pain ...

Linear and nonlinear development of m=0 instability in a diffuse Bennett Z-pinch equilibrium with sheared axial flow

International Nuclear Information System (INIS)

Paraschiv, I.; Bauer, B. S.; Lindemuth, I. R.; Makhin, V.

2010-01-01

The effect of sheared axial flow on the Z-pinch sausage instability has been examined with two-dimensional magnetohydrodynamic simulations. Diffuse Bennett equilibria in the presence of axial flows with parabolic and linear radial profiles have been considered, and a detailed study of the linear and nonlinear development of small perturbations from these equilibria has been performed. The consequences of both single-wavelength and random-seed perturbations were calculated. It was found that sheared flows changed the internal m=0 mode development by reducing the linear growth rates, decreasing the saturation amplitude, and modifying the instability spectrum. High spatial frequency modes were stabilized to small amplitudes and only long wavelengths continued to grow. Full stability was obtained for supersonic plasma flows.

Dense sheet Z-pinches

International Nuclear Information System (INIS)

Tetsu, Miyamoto

1999-01-01

The steady state and quasi-steady processes of infinite- and finite-width sheet z-pinches are studied. The relations corresponding to the Bennett relation and Pease-Braginskii current of cylindrical fiber z-pinches depend on a geometrical factor in the sheet z-pinches. The finite-width sheet z-pinch is approximated by a segment of infinite-width sheet z-pinch, if it is wide enough, and corresponds to a number of (width/thickness) times fiber z-pinch plasmas of the diameter that equals the sheet thickness. If the sheet current equals this number times the fiber current, the plasma created in the sheet z-pinches is as dense as in the fiber z-pinches. The total energy of plasma and magnetic field per unit mass is approximately equal in both pinches. Quasi-static transient processes are different in several aspects from the fiber z-pinch. No radiation collapse occurs in the sheet z-pinch. The stability is improved in the sheet z-pinches. The fusion criterions and the experimental arrangements to produce the sheet z-pinches are also discussed. (author)

Energy storage and transfer with homopolar machine for a linear theta-pinch hybrid reactor

International Nuclear Information System (INIS)

Vogel, H.F.; Brennan, M.; Dase, W.G.; Tolk, K.M.; Weldon, W.F.

1975-12-01

This report describes the energy storage and transfer system for the compression coil system of a linear theta-pinch hybrid reactor (LTPHR). High efficiency and low cost are the principal requirements for the energy storage and transfer of 25 MJ/m or 25 GJ for a 1-km LTPHR. The circuit efficiency must be approximately 90 percent, and the cost for the circuit 5 to 6 cents/J. Scaling laws and simple relationships between circuit efficiency and cost per unit energy as a function of the half cycle time are presented. Capacitors and homopolor machines are considered as energy storage elements with both functioning basically as capacitors. The advantage of the homopolar machine in this application is its relatively low cost, whereas that of capacitors is better efficiency

The physics of reversed-field pinch profile sustainment

International Nuclear Information System (INIS)

Moses, R.W.

1985-01-01

A description of the Reversed-Field Pinch (RFP) is given. There is experimental evidence that indicates that an RFP dynamo effect sustains field reversal in steady state. Three sustainment mechanisms are reviewed: the MHD model, the tangled discharge model, and the kinetic dynamo model. The relationship of these models to each another is discussed briefly

The role of radial particle pinches in ELM suppression by resonant magnetic perturbations

International Nuclear Information System (INIS)

Stacey, W.M.; Evans, T.E.

2011-01-01

The force balance in the plasma edge in a matched pair of DIII-D (Luxon 2002 Nucl. Fusion 42 6149) tokamak discharges with and without resonant magnetic perturbations (RMPs) is evaluated in order to investigate the effects on particle transport of RMP applied for the purpose of suppressing edge-localized modes (ELMs). Experimental data are used to evaluate the radial and toroidal force balances, which may be written as a pinch-diffusion relation for the radial ion flux to facilitate investigation of transport effects. The radial electric field in the H-mode plasma had a sharp negative dip in the steep gradient region of the edge pedestal, associated with which was a large inward pinch velocity. The main effect of RMP was to make the edge electric field less negative or more positive, reducing this strong negative dip in the radial electric field (even reversing it from negative to positive over some regions), thereby reducing the strong inward particle pinch in the edge of an H-mode discharge, thus causing a reduction in edge density below the ELM threshold.

Kinetic theory of the sausage instability of a z-pinch

International Nuclear Information System (INIS)

Isichenko, M.B.; Kulyabin, K.L.; Yan'kov, V.V.

1989-01-01

A linear problem of z-pinch sausage development is considered taking into account the influence of kinetic effects for ideal scanning current. Plasma electrons are considered to be cold and ions - collisionless. It is also supposed that the magnetic field inside a pinch doesn't affect the motion of ions, which are reflected like in a mirror from a jump of an electric potential arising on the plasma boundary. In case of long-wave perturbations ka >1 the acount of kinetics leads to considerable decrease of the increment [(ka) 1/2 times] in comparison with the hydrodynamic description, that permits to explain the increased instability of z-pinches observed in experiments

LASL toroidal reversed-field pinch program

International Nuclear Information System (INIS)

Baker, D.A.; Buchenauer, C.J.; Burkhardt, L.C.

1978-01-01

The determination of the absolute energy loss due to radiation from impurities in the LASL toroidal reversed-field pinch experiment ZT-S is reported. The measurements show over half of the energy loss is accounted for by this mechanism. Thomson scattering electron density measurements indicate only a gradual increase in temperature as the filling pressure is reduced indicating an increased energy loss at lower pressures. Cylindrical and toroidal simulations of the experiment indicate either that a highly radiative pinch boundary or anomalous transport are needed to match the experimental results. New effects on the equilibrium due to plasma flows induced by the toroidal geometry are predicted by the toroidal simulations. The preliminary results on the low temperature discharge cleaning of the ZT-S torus are reported. A description of the upgrade of the ZT-S experiment and the objectives, construction and theoretical predictions for the new ZT-40 experiment are given

Ultra-low q and reversed field pinch experiments in Extrap T1 with a resistive shell

International Nuclear Information System (INIS)

Brunsell, P.; Drake, J.R.; Mazur, S.; Nordlund, P.

1991-02-01

The Extrap T1 device is a high aspect ratio toroidal pinch with the dimensions R/a = 0.5 m/0.057 m. In the experiments described here, the stainless steel bellows vacuum vessels was surrounded by a resistive shell with a perpendicular field penetration time of 75 μs. The ULQ discharges, with toroidal currents in the range 20-50 kA and pulse lengths up to 2 ms, showed the typical step-wise decay of the plasma current. The current steps corresponded to transitions of the edge q-value across rational values 1/4, 1/3, 1/2, and 1. During a step through a rational q value, there was an increase in the fluctuation activity and a corresponding increase in the plasma resistance. As part of the ULQ studies, discharges with four poloidal field nulls were produced by applying an octupole magnetic field, thus demonstrating that it is possible to sustain ULQ equilibria with poloidal field x-points and a magnetic separatix. In another study, the transition from ULQ discharges to relaxed state discharges was investigated. When the initial bias toroidal field was reduced so that q was less than about 1/6, which corresponded to a pinch parameter of about 0.6, a change in the discharge character was observed. The loop voltage required to sustain a given current increased and stochastic fluctuations were seen. Toroidal flux was generated and relaxed state equilibira developed. For higher pinch parameter, in the range of 1.5 to 2.0, a reversed field pinch could be set up if the toroidal field power supply provided a reversed current in the coils. The plasma resistivity was again lower and the pulse lengths in the RFP mode were up to 1 ms, corresponding to over 10 shell penetration times. (au)

Evaluation of Particle Pinch and Diffusion Coefficients in the Edge Pedestal of DIII-D H-mode Discharges

Science.gov (United States)

Stacey, W. M.; Groebner, R. J.

2009-11-01

Momentum balance requires that the radial particle flux satisfy a pinch-diffusion relationship. The pinch can be evaluated in terms of measurable quantities (rotation velocities, Er, etc.) by the use of momentum and particle balance [1,2], the radial particle flux can be determined by momentum balance, and then the diffusion coefficient can be evaluated from the pinch diffusion relation using the measured density gradient. Applications to several DIII-D H-mode plasmas are presented. 6pt [1] W.M. Stacey, Contr. Plasma Phys. 48, 94 (2008). [2] W.M. Stacey and R.J. Groebner, Phys. Plasmas 15, 012503 (2008).

Neutron emission generated during wire array Z-pinch implosion onto deuterated fiber

Czech Academy of Sciences Publication Activity Database

Klir, D.; Kravarik, J.; Kubes, P.; Rezac, K.; Ananev, S.S.; Bakshaev, Yu. L.; Blinov, P. I.; Chernenko, A. S.; Kazakov, E.D.; Korolev, V. D.; Meshcherov, B.R.; Ustroev, G. I.; Juha, Libor; Krása, Josef; Velyhan, Andriy

2008-01-01

Roč. 15, č. 3 (2008), 32701/1-32701/13 ISSN 1070-664X R&D Projects: GA MŠk(CZ) LC528; GA MŠk LA08024 Institutional research plan: CEZ:AV0Z10100523 Keywords : fusion plasmas * d-d reaction * neutron yield * Z pinch * high-current discharges Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.427, year: 2008

Stable Alfven-wave dynamo action in the reversed-field pinch

International Nuclear Information System (INIS)

Werley, K.A.

1984-01-01

Previous theoretical work has suggested that Alfven waves may be related to the anomalous toroidal magnetic flux generation and extended (over classical expectations) discharge times observed in the reversed-field pinch. This thesis examines the dynamo action of stable Alfven waves as a means of generating toroidal flux. Recent advances in linear resistive MHD stability analysis are used to calculate the quasi-linear dynamo mean electromotive force of Alfven waves. This emf is incorporated into a one-dimensional transport and mean-field evolution code. The changing equilibrium is then fed back to the stability code to complete a computational framework that self-consistently evaluates a dynamic plasma dynamo. This technique is readily extendable to other plasmas in which dynamic stable model action is of interest. Such plasmas include Alfven wave current-drive and plasma heating for fusion devices, as well as astrophysical and geophysical dynamo systems. This study also contains extensive studies of resistive Alfven wave properties. This includes behavior versus spectral location, magnetic Reynolds number and wave number

Design of a 5-MA 100-ns linear-transformer-driver accelerator for wire array Z-pinch experiments

Science.gov (United States)

Zhou, Lin; Li, Zhenghong; Wang, Zhen; Liang, Chuan; Li, Mingjia; Qi, Jianmin; Chu, Yanyun

2016-03-01

The linear-transformer-driver (LTD) is a recently developed pulsed-power technology that shows great promise for a number of applications. These include a Z -pinch-driven fission-fusion-hybrid reactor that is being developed by the Chinese Academy of Engineering Physics. In support of the reactor development effort, we are planning to build an LTD-based accelerator that is optimized for driving wire-array Z -pinch loads. The accelerator comprises six modules in parallel, each of which has eight series 0.8-MA LTD cavities in a voltage-adder configuration. Vacuum transmission lines are used from the interior of the adder to the central vacuum chamber where the load is placed. Thus the traditional stack-flashover problem is eliminated. The machine is 3.2 m tall and 12 m in outer diameter including supports. A prototype cavity was built and tested for more than 6000 shots intermittently at a repetition rate of 0.1 Hz. A novel trigger, in which only one input trigger pulse is needed by utilizing an internal trigger brick, was developed and successfully verified in these shots. A full circuit modeling was conducted for the accelerator. The simulation result shows that a current pulse rising to 5.2 MA in 91 ns (10%-90%) can be delivered to the wire-array load, which is 1.5 cm in height, 1.2 cm in initial radius, and 1 mg in mass. The maximum implosion velocity of the load is 32 cm /μ s when compressed to 0.1 of the initial radius. The maximum kinetic energy is 78 kJ, which is 11.7% of the electric energy stored in the capacitors. This accelerator is supposed to enable a radiation energy efficiency of 20%-30%, providing a high efficient facility for research on the fast Z pinch and technologies for repetition-rate-operated accelerators.

Electrostatic Discharge Current Linear Approach and Circuit Design Method

Directory of Open Access Journals (Sweden)

Pavlos K. Katsivelis

2010-11-01

Full Text Available The Electrostatic Discharge phenomenon is a great threat to all electronic devices and ICs. An electric charge passing rapidly from a charged body to another can seriously harm the last one. However, there is a lack in a linear mathematical approach which will make it possible to design a circuit capable of producing such a sophisticated current waveform. The commonly accepted Electrostatic Discharge current waveform is the one set by the IEC 61000-4-2. However, the over-simplified circuit included in the same standard is incapable of producing such a waveform. Treating the Electrostatic Discharge current waveform of the IEC 61000-4-2 as reference, an approximation method, based on Prony’s method, is developed and applied in order to obtain a linear system’s response. Considering a known input, a method to design a circuit, able to generate this ESD current waveform in presented. The circuit synthesis assumes ideal active elements. A simulation is carried out using the PSpice software.

LASL toroidal reversed-field pinch programme

International Nuclear Information System (INIS)

Baker, D.A.; Buchenauer, C.J.; Burkhardt, L.C.

1979-01-01

The determination of the absolute energy loss due to radiation from impurities in the LASL toroidal reversed-field pinch experiment ZT-S is reported. The measurements show that over half the energy loss is accounted for by this mechanism. Thomson-scattering electron density measurements indicate only a gradual increase in temperature as the filling pressure is reduced, indicating an increased energy loss at lower pressures. Cylindrical and toroidal simulations of the experiment indicate either that a highly radiative pinch boundary or anomalous transport is needed to match the experimental results. New effects on the equilibrium due to plasma flows induced by the toroidal geometry are predicted by the toroidal simulations. The preliminary results on the low-temperature discharge cleaning of the ZT-S torus are reported. A description of the upgrade of the ZT-S experiment and the objectives, construction and theoretical predictions for the new ZT-40 experiment are given. (author)

A comparison between linear and toroidal Extrap systems

International Nuclear Information System (INIS)

Lehnert, B.

1988-09-01

The Extrap scheme consists of a Z-pinch immersed in an octupole field generated by currents in a set of external conductors. A comparison between linear and toroidal Extrap geometry is made in this paper. As compared to toroidal systems, linear geometry has the advantages of relative simplicity and of a current drive by means of electrodes. Linear devices are convenient for basic studies of Extrap, at moderately high pinch currents and plasma temperatures. Within the parameter ranges of experiments at high pinch currents and plasma temperatures, linear systems have on the other hand some substantial disadvantages, on account of the plasma interaction with the end regions. This results in a limitation of the energy confinement time, and leads in the case of an ohmically heated plasma to excessively high plasma densities and small pinch radii which also complicate the introduction of the external conductors. (author)

Finite-Larmor-radius effects on z-pinch stability

Science.gov (United States)

Scheffel, Jan; Faghihi, Mostafa

1989-06-01

The effect of finite Larmor radius (FLR) on the stability of m = 1 small-axial-wavelength kinks in a z-pinch with purely poloidal magnetic field is investigated. We use the incompressible FLR MHD model; a collisionless fluid model that consistently includes the relevant FLR terms due to ion gyroviscosity, Hall effect and electron diamagnetism. With FLR terms absent, the Kadomtsev criterion of ideal MHD, 2r dp/dr + m2B2/μ0 ≥ 0 predicts instability for internal modes unless the current density is singular at the centre of the pinch. The same result is obtained in the present model, with FLR terms absent. When the FLR terms are included, a normal-mode analysis of the linearized equations yields the following results. Marginally unstable (ideal) modes are stabilized by gyroviscosity. The Hall term has a damping (but not absolutely stabilizing) effect - in agreement with earlier work. On specifying a constant current and particle density equilibrium, the effect of electron diamagnetism vanishes. For a z-pinch with parameters relevant to the EXTRAP experiment, the m = 1 modes are then fully stabilized over the crosssection for wavelengths λ/a ≤ 1, where a denotes the pinch radius. As a general z-pinch result a critical line-density limit Nmax = 5 × 1018 m-1 is found, above which gyroviscous stabilization near the plasma boundary becomes insufficient. This limit corresponds to about five Larmor radii along the pinch radius. The result holds for wavelengths close to, or smaller than, the pinch radius and for realistic equilibrium profiles. This limit is far below the required limit for a reactor with contained alpha particles, which is in excess of 1020 m-1.

Finite-Larmor-radius effects on z-pinch stability

Energy Technology Data Exchange (ETDEWEB)

Scheffel, J.; Faghihi, M. (Royal Inst. of Tech., Stockholm (Sweden))

1989-06-01

The effect of finite Larmor radius (FLR) on the stability of m = 1 small-axial-wavelength kinks in a z-pinch with purely poloidal magnetic field is investigated. The incompressible FLR MHD model is used; a collisionless fluid model that consistently includes the relevant FLR terms due to ion gyroviscosity, Hall effect and electron diamagnetism. With FLR terms absent, the Kadomtsev criterion of ideal MHD, 2rdp/dr+m{sup 2}B{sup 2}/{mu}{sub 0}{ge}0 predicts instability for internal modes unless the current density is singular at the centre of the pinch. The same result is obtained in the present model, with FLR terms absent. When the LFR terms are included, a normal-mode analysis of the linearized equations yields the following results. Marginally unstable (ideal) modes are stabilized by gyroviscosity. The Hall term has a damping (but no absolutely stabilizing) effect - in agreement with earlier work. On specifying a constant current and particle density equilibrium, the effect of electron diamagnetism vanishes. For a z-pinch with parameters relevant to the EXTRAP experiment, the m = 1 modes are then fully stabilized over the cross-section for wavelengths {lambda}/{alpha}{le}1, where {alpha} denotes the pinch radius. As a general z-pinch result a critical line-density limit ''N''{sub max}=5x10{sup 18}m{sup -1} is found, above which gyroviscous stabilization near the plasma boundary becomes insufficient. This limit corresponds to about five Larmor radii along the pinch radius. The result holds for wavelengths close to, or smaller than, the pinch radius and for realistic equilibrium profiles. This limit is far below the required limit for a reactor with contained alpha particles, which is in excess of 10{sup 20} m{sup -1}. (author).

Finite-Larmor-radius effects on z-pinch stability

International Nuclear Information System (INIS)

Scheffel, J.; Faghihi, M.

1989-01-01

The effect of finite Larmor radius (FLR) on the stability of m = 1 small-axial-wavelength kinks in a z-pinch with purely poloidal magnetic field is investigated. The incompressible FLR MHD model is used; a collisionless fluid model that consistently includes the relevant FLR terms due to ion gyroviscosity, Hall effect and electron diamagnetism. With FLR terms absent, the Kadomtsev criterion of ideal MHD, 2rdp/dr+m 2 B 2 /μ 0 ≥0 predicts instability for internal modes unless the current density is singular at the centre of the pinch. The same result is obtained in the present model, with FLR terms absent. When the LFR terms are included, a normal-mode analysis of the linearized equations yields the following results. Marginally unstable (ideal) modes are stabilized by gyroviscosity. The Hall term has a damping (but no absolutely stabilizing) effect - in agreement with earlier work. On specifying a constant current and particle density equilibrium, the effect of electron diamagnetism vanishes. For a z-pinch with parameters relevant to the EXTRAP experiment, the m = 1 modes are then fully stabilized over the cross-section for wavelengths λ/α≤1, where α denotes the pinch radius. As a general z-pinch result a critical line-density limit ''N'' max =5x10 18 m -1 is found, above which gyroviscous stabilization near the plasma boundary becomes insufficient. This limit corresponds to about five Larmor radii along the pinch radius. The result holds for wavelengths close to, or smaller than, the pinch radius and for realistic equilibrium profiles. This limit is far below the required limit for a reactor with contained alpha particles, which is in excess of 10 20 m -1 . (author)

Flow effects on the stability of z-pinches

International Nuclear Information System (INIS)

Shumlak, U.; Hartman, C.W.

1996-01-01

The effect of an axial flow on the m = 1 kink instability in z-pinches is studied numerically by reducing the linearized ideal MHD equations to a one-dimensional eigenvalue equation for the radial displacement. The derivation of the displacement equation for equilibria with axial flows will be presented. A diffuse z-pinch equilibrium is chosen that is made marginally stable to the m = 0 sausage mode by tailoring the pressure profile. The principle result reveals that a sheared axial flow does stabilize the kink mode when the shear exceeds a threshold value. Additionally, the m = 0 sausage mode is driven from marginal stability into the stable regime which suggests that the equilibrium pressure profile control can be relaxed. Fast z-pinches such as liner implosions are plagued by the Rayleigh-Taylor instability which destroys the liner and disrupts the current path before the liner arrives on axis. A sheared axial flow in a liner may quench the Rayleigh-Taylor instability in the same way that it quenches MHD instabilities in a diffuse z-pinch. Simulation results will be presented showing the effect of a sheared axial flow on the Rayleigh-Taylor instability in a fast liner implosion

Z-pinches

International Nuclear Information System (INIS)

Yan'kov, V.V.

1991-01-01

Although pinches, unlike tokamaks, have not occupied a central position in fusion research, their structural simplicity and the wealth of physical processes associated with plasma foci have maintained a steady interest. The development of Z-pinches, including plasma foci, micropinches, and dense Z-pinches, is reviewed. Attention is focused on theoretical as opposed to experimental questions, and on recent work rather than the basic results now found in textbooks. Finally, Soviet work is discussed more fully than work done abroad, and applications to controlled fusion are emphasized

Solid fiber Z-pinches

International Nuclear Information System (INIS)

Lindemuth, I.R.

1989-01-01

One- and two-dimensional magnetohydrodynamic computations have been performed to study the behavior of solid deuterium fiber Z-pinch experiments performed at Los Alamos and the Naval Research Laboratory. The computations use a tabulated atomic data base and ''cold-start'' initial conditions. The computations predict that the solid fiber persists longer in existing experiments than previously expected and that the discharge actually consists of a relatively low-density, hot plasma which has been ablated from the fiber. The computations exhibit m = 0 behavior in the hot, exterior plasma prior to complete ablation of the solid fiber. The m = 0 behavior enhances the fiber ablation rate. 10 refs., 5 figs

Evident anomalous inward particle pinch in full non-inductive plasmas driven by lower hybrid waves on Tore Supra

International Nuclear Information System (INIS)

Hoang, G.T.; Bourdelle, C.; Pegourie, B.; Artaud, J.F.; Bucalossi, J.; Clairet, F.; Fenzi-Bonizec, C.; Garbet, X.; Gil, C.; Guirlet, R.; Imbeaux, F.; Lasalle, J.; Loarer, T.; Lowry, C.; Schunke, B.; Travere, J.M.; Tsitrone, E.

2003-01-01

These slides present some characteristics concerning peaked density profile observed in Tore-Supra. It appears that density profile remains peaked for more than 3 minutes in fully LHCD (lower hybrid current drive) discharges. The absence of toroidal electric field and the fact that the ware pinch has vanished across the entire plasma show that toroidal electric field and ware pinch are not the cause of the peaked profile. It is shown that peaked profile is linked to transport properties and can only be explained by a particle pinch velocity 2 orders of magnitude above the neoclassical pinch. It is also shown that the radial profile is in agreement with Isitchenko's formula. (A.C.)

Architecture of petawatt-class z-pinch accelerators

Directory of Open Access Journals (Sweden)

W. A. Stygar

2007-03-01

Full Text Available We have developed an accelerator architecture that can serve as the basis of the design of petawatt-class z-pinch drivers. The architecture has been applied to the design of two z-pinch accelerators, each of which can be contained within a 104-m-diameter cylindrical tank. One accelerator is driven by slow (∼1   μs Marx generators, which are a mature technology but which necessitate significant pulse compression to achieve the short pulses (≪1   μs required to drive z pinches. The other is powered by linear transformer drivers (LTDs, which are less mature but produce much shorter pulses than conventional Marxes. Consequently, an LTD-driven accelerator promises to be (at a given pinch current and implosion time more efficient and reliable. The Marx-driven accelerator produces a peak electrical power of 500 TW and includes the following components: (i 300 Marx generators that comprise a total of 1.8×10^{4} capacitors, store 98 MJ, and erect to 5 MV; (ii 600 water-dielectric triplate intermediate-store transmission lines, which also serve as pulse-forming lines; (iii 600 5-MV laser-triggered gas switches; (iv three monolithic radial-transmission-line impedance transformers, with triplate geometries and exponential impedance profiles; (v a 6-level 5.5-m-diameter 15-MV vacuum insulator stack; (vi six magnetically insulated vacuum transmission lines (MITLs; and (vii a triple-post-hole vacuum convolute that adds the output currents of the six MITLs, and delivers the combined current to a z-pinch load. The accelerator delivers an effective peak current of 52 MA to a 10-mm-length z pinch that implodes in 95 ns, and 57 MA to a pinch that implodes in 120 ns. The LTD-driven accelerator includes monolithic radial transformers and a MITL system similar to those described above, but does not include intermediate-store transmission lines, multimegavolt gas switches, or a laser trigger system. Instead, this accelerator is driven by 210

MHD simulations of molybdenum X-pinches

International Nuclear Information System (INIS)

Ivanenkov, G.V.; Stepnevski, V.

2002-01-01

One investigates into compression of molybdenum X-pinches applying numerical MHD-models with parabolic and conical initial geometry. The second model describing plasma axial motion in greater detail offers a real geometry of a discharge and is applicable to loads characterized by higher masses in contrast to the first one. Both models enabled to describe all basic phases of compression including origination of a minidiode, occurrence of a narrow neck, microexplosion of a hot point and origination of shock waves followed by sausage instability [ru

Confinement characteristics of the TPE reversed field pinch plasmas and effects of the boundary configuration

International Nuclear Information System (INIS)

Yagi, Y.; Maejima, Y.; Zollino, G.

2001-01-01

Confinement characteristics of the TPE series reversed field pinch (RFP) machines, TPE-1RM15, TPE-1RM20 and TPE-1RM20mod, at Electrotechnical Laboratory (ETL) are summarized. Especially data are synthesized in respect to the effects of the different boundary structures of the machines, where shell proximity and overlapped poloidal shell gaps by the multi-layered shell structure are featured. Comparison of the experimental results is shown in terms of the characteristics of magnetic fluctuations, global confinement properties in general, operation capability of the improved confinement in high pinch parameter (Q) discharges and locked mode events. Linear growth rate of the unstable modes as a function of the shell distance is numerically simulated. Understandings of RFP plasma physics have also made progress by the most recent intensive experiments on correlation studies between fast electrons and dynamo activities and measurement of the plasma and mode rotation. TPE-1RM20mod was shutdown in December 1996 and new RFP experiment has started in TPE-RX from March 1998. The new machine also succeeds the concept of the shell configuration of the TPE-1RM20. (author)

Plasma experiments on staged theta pinch, implosion heating experiment and Scyllac feedback-sector experiment

International Nuclear Information System (INIS)

Bartsch, R.R.; Buchenauer, C.J.; Cantrell, E.L.

1977-01-01

Results of the Los Alamos theta-pinch program in three areas of investigation are summarized: 1) In the Staged Theta Pinch, results are reported on the effects of magnetic field amplitude and time history of plasma formation. 2) In the Implosion Heating Experiment, density, internal-magnetic field and neutron measurements yield a consistent picture of the implosion which agrees with kinetic computations and with a simple dynamic model of the ions and magnetic piston. 3) In the Scyllac Feedback-Sector Experiment, the l=1, 0 equilibrium plasma parameters have been adjusted to accommodate the feedback stabilization system. With a uniform toroidal discharge tube the m=1 instability is feedback-stabilized in the vertical direction, and confinement in the toroidal direction is extended by feedback control. Results with a helical discharge tube are also reported. (author)

Energy storage and transfer with homopolar machine for a linear theta-pinch hybrid reactor

International Nuclear Information System (INIS)

Vogel, H.F.; Brennan, M.; Dase, W.G.; Tolk, K.M.; Weldon, W.F.

1976-01-01

The energy storage and transfer system for the compression coils of a linear theta-pinch hybrid reactor (LTPHR) are described. High efficiency and low cost are the principal requirements for the energy storage and transfer of 25MJ/m or 25GJ for a 1-km LTPHR. The circuit efficiency must be approximately 90%, and the cost for the circuit 5-6c/J. Scaling laws and simple relationships between circuit efficiency and cost-per-unit energy as a function of the half cycle time are presented. An important consideration concerns the pulse repetition rate of 2.25 pulses per second, 70x10 6 shots/yr, or 1.7x10 9 shots over the 25-yr plant life. Current interruption to initiate energy transfer is not feasible at this rate. Therefore, a simple ringing circuit with contactors to make and break at the periodically occurring zero-current instances, is considered

Structural design aspects of magnetic coils for a linear theta-pinch hybrid reactor

International Nuclear Information System (INIS)

Bartholomew, R.J.

1976-02-01

The structural design aspects of a linear theta-pinch hybrid reactor (LTPHR) are centered in the solenoidal adiabatic compression coil (ACC) which must support the high magnetic pulse forces that tend to expand the coil and separate the leads. The structural model is represented by the theory of elasticity solution to a thick-walled cylinder. Dynamic amplification (or attenuation) is considered by a shock spectrum technique. A composite material is postulated, where the conductor material for each strand is clad with a high-strength stainless steel with insulation considered. Yield strength (for isolated-pulse operation) and endurance limit (for repetitive-pulse operation) for the high-strength steel impose magnetic field strength constraints on the coil design. These constraints are combined in an overall energy balance calculation that includes neutronic considerations to determine an optimum ACC design. The computer code ENBAL was used to incorporate neutronic, electrical, and structural constraints into the overall energy balance of the LTPHR. The lead separation problem is solved by designing spaced clamps to hold the leads together over great distances

Design of the PST: A Diagnostic for 1-D Imaging of Fast Z-Pinch Power Emissions

International Nuclear Information System (INIS)

Rochau, Gregory A.; Derzon, Mark S.; Chandler, Gordon A.; Lazier, Steven Earl

2000-01-01

Fast Z-pinch technology developed on the Z machine at Sandia National Laboratories can produce up to 230 TW of thermal x-ray power for applications in inertial confinement fusion (ICF) and weapons physics experiments. During implosion, these Z-pinches develop Rayleigh-Taylor (R-T) instabilities which are very difficult to diagnose and which functionally diminish the overall pinch quality. The Power-Space-Time (PST) instrument is a newly configured diagnostic for measuring the pinch power as a function of both space and time in a Z-pinch. Placing the diagnostic at 90 degrees from the Z-pinch axis, the PST provides a new capability in collecting experimental data on R-T characteristics for making meaningful comparisons to magneto-hydrodynamic computer models. This paper is a summary of the PST diagnostic design. By slit-imaging the Z-pinch x-ray emissions onto a linear scintillator/fiber-optic array coupled to a streak camera system, the PST can achieve ∼100 microm spatial resolution and ∼1.3 ns time resolution. Calculations indicate that a 20 microm thick scintillating detection element filtered by 1,000 angstrom of Al is theoretically linear in response to Plankian x-ray distributions corresponding to plasma temperatures from 40 eV to 150 eV, By calibrating this detection element to x-ray energies up to 5,000 eV, the PST can provide pinch power as a function of height and time in a Z-pinch for temperatures ranging from ∼40 eV to ∼400 eV. With these system pm-meters, the PST can provide data for an experimental determination of the R-T mode number, amplitude, and growth rate during the late-time pinch implosion

Modelling of capillary Z-pinch recombination pumping of boron extreme ultraviolet laser

Czech Academy of Sciences Publication Activity Database

Vrba, Pavel; Bobrova, N. A.; Sasorov, P. V.; Vrbová, M.; Hübner, Jakub

2009-01-01

Roč. 16, č. 7 (2009), 073105 1-073105 11 ISSN 1070-664X R&D Projects: GA ČR GA102/07/0275 Institutional research plan: CEZ:AV0Z20430508 Keywords : Boron * capillary * discharges (electric * laser ablation * optical pumping * plasma heating by laser * plasma kinetic theory * plasma magnetohydrodynamics * Z pinch Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.475, year: 2009 http://link.aip.org/link/? PHP /16/073105

Non-linear macro evolution of a dc driven micro atmospheric glow discharge

Energy Technology Data Exchange (ETDEWEB)

Xu, S. F.; Zhong, X. X., E-mail: xxzhong@sjtu.edu.cn [The State Key Laboratory on Fiber Optic Local Area, Communication Networks and Advanced Optical Communication Systems, Key Laboratory for Laser Plasmas and Department of Physics and Astronomy, Shanghai Jiao Tong University, Shanghai 200240 (China)

2015-10-15

We studied the macro evolution of the micro atmospheric glow discharge generated between a micro argon jet into ambient air and static water. The micro discharge behaves similarly to a complex ecosystem. Non-linear behaviors are found for the micro discharge when the water acts as a cathode, different from the discharge when water behaves as an anode. Groups of snapshots of the micro discharge formed at different discharge currents are captured by an intensified charge-coupled device with controlled exposure time, and each group consisted of 256 images taken in succession. Edge detection methods are used to identify the water surface and then the total brightness is defined by adding up the signal counts over the area of the micro discharge. Motions of the water surface at different discharge currents show that the water surface lowers increasingly rapidly when the water acts as a cathode. In contrast, the water surface lowers at a constant speed when the water behaves as an anode. The light curves are similar to logistic growth curves, suggesting that a self-inhibition process occurs in the micro discharge. Meanwhile, the total brightness increases linearly during the same time when the water acts as an anode. Discharge-water interactions cause the micro discharge to evolve. The charged particle bomb process is probably responsible for the different behaviors of the micro discharges when the water acts as cathode and anode.

Design of a 5-MA 100-ns linear-transformer-driver accelerator for wire array Z-pinch experiments

Directory of Open Access Journals (Sweden)

Zhou Lin

2016-03-01

Full Text Available The linear-transformer-driver (LTD is a recently developed pulsed-power technology that shows great promise for a number of applications. These include a Z-pinch-driven fission-fusion-hybrid reactor that is being developed by the Chinese Academy of Engineering Physics. In support of the reactor development effort, we are planning to build an LTD-based accelerator that is optimized for driving wire-array Z-pinch loads. The accelerator comprises six modules in parallel, each of which has eight series 0.8-MA LTD cavities in a voltage-adder configuration. Vacuum transmission lines are used from the interior of the adder to the central vacuum chamber where the load is placed. Thus the traditional stack-flashover problem is eliminated. The machine is 3.2 m tall and 12 m in outer diameter including supports. A prototype cavity was built and tested for more than 6000 shots intermittently at a repetition rate of 0.1 Hz. A novel trigger, in which only one input trigger pulse is needed by utilizing an internal trigger brick, was developed and successfully verified in these shots. A full circuit modeling was conducted for the accelerator. The simulation result shows that a current pulse rising to 5.2 MA in 91 ns (10%–90% can be delivered to the wire-array load, which is 1.5 cm in height, 1.2 cm in initial radius, and 1 mg in mass. The maximum implosion velocity of the load is 32  cm/μs when compressed to 0.1 of the initial radius. The maximum kinetic energy is 78 kJ, which is 11.7% of the electric energy stored in the capacitors. This accelerator is supposed to enable a radiation energy efficiency of 20%–30%, providing a high efficient facility for research on the fast Z pinch and technologies for repetition-rate-operated accelerators.

Oscillating field current drive for reversed field pinch discharges

International Nuclear Information System (INIS)

Schoenberg, K.F.; Gribble, R.F.; Baker, D.A.

1984-06-01

Oscillating Field Current Drive (OFCD), also known as F-THETA pumping, is a steady-state current-drive technique proposed for the Reversed Field Pinch (RFP). Unlike other current-drive techniques, which employ high-technology, invasive, and power intensive schemes using radio frequency or neutral particle injection, F-THETA pumping entails driving the toroidal and poloidal magnetic field circuits with low-frequency (audio) oscillating voltage sources. Current drive by this technique is a consequence of the strong nonlinear plasma coupling in the RFP. Because of its low frequency and efficient plasma coupling, F-THETA pumping shows excellent promise as a reactor-relevant current-drive technique. A conceptual and computational study of this concept, including its experimental and reactor relevance, is explored in this paper

Charger 1: A New Facility for Z-Pinch Research

Science.gov (United States)

Taylor, Brian; Cassibry, Jason; Cortez, Ross; Doughty, Glen; Adams, Robert; DeCicco, Anthony

2017-01-01

Charger 1 is a multipurpose pulsed power laboratory located on Redstone Arsenal, with a focus on fusion propulsion relevant experiments involving testing z-pinch diodes, pulsed magnetic nozzle and other related physics experiments. UAH and its team of pulsed power researchers are investigating ways to increase and optimize fusion production from Charger 1. Currently the team has reached high-power testing. Due to the unique safety issues related to high power operations the UAH/MSFC team has slowed repair efforts to develop safety and operations protocols. The facility is expected to be operational by the time DZP 2017 convenes. Charger 1 began life as the Decade Module 2, an experimental prototype built to prove the Decade Quad pinch configuration. The system was donated to UAH by the Defense Threat Reduction Agency (DRTA) in 2012. For the past 5 years a UAH/MSFC/Boeing team has worked to refurbish, assemble and test the system. With completion of high power testing in summer 2017 Charger 1 will become operational for experimentation. Charger 1 utilizes a Marx Bank of 72 100-kV capacitors that are charged in parallel and discharged in series. The Marx output is compressed to a pulse width of approximately 200 ns via a pulse forming network of 32 coaxial stainless steel tubes using water as a dielectric. After pulse compression a set of SF6 switches are triggered, allowing the wave front to propagate through the output line to the load. Charger 1 is capable of storing 572-kJ of energy and time compressing discharge to less than 250 ns discharge time producing a discharge of about 1 TW of discharge with 1 MV and 1 MA peak voltage and current, respectively. This capability will be used to study energy yield scaling and physics from solid density target as applied to advanced propulsion research.

Revised field pinch experiments. Annual progress report, June 1, 1984-May 31, 1985

International Nuclear Information System (INIS)

Robertson, S.

1985-01-01

The dielectric breaks in the Reversatron vacuum chamber were replaced by bellows sections in December 1984, and operation was resumed in January 1985. The plasma current was limited to 20 kA due to the inefficiency of the air-core transformer. RFP discharges were not obtained due to the pinch parameter theta being below the required value of 1.6. Diagnostics indicated n approx. 4 x 10 13 cm -3 and T/sub e/ approx. 75 eV. Inductively decoupled vertical field coils were used to vary the equilibrium position of the plasma and to maximize the plasma current. A new air-core transformer is being installed which will give an increased plasma current and pinch parameter. Operation with the shell in place will begin in June 1985. If adequate theta values and RFP discharges are obtained, operation without the shell will begin in October 1985

Collisional tearing in a field-reversed sheet pinch assuming nonparallel propagation

International Nuclear Information System (INIS)

Quest, K.B.; Coroniti, F.V.

1985-01-01

We examine the linear stability properties of the collisional tearing mode in a reversed-field sheet pinch assuming that the wave vector is not parallel to B, where B is the equilibrium magnetic field. We show that pressure balance in the direction of the equilibrium current requires a nonzero perturbed current component deltaJ/sub z/ that is driven toward tyhe center of the pinch. At the center of the pinch, deltaJ/sub z/ goes to zero, and momentum is balanced by coupling to the ion-acoustic mode. In order to achieve current closure, a large perturbed field-aligned current is generated that is strongly localized about the dissipative tearing layer. The relation of this work to the collisionless case is discussed

Research on pinch devices of tens of kA to MA

Energy Technology Data Exchange (ETDEWEB)

Soto, L.; Silva, P.; Moreno, J.; Silvester, G.; Zambra, M. [Comision Chilena de Energia Nuclear, Santiago (Chile); Pavez, C.; Saavedra, R. [Univ. de Concepcion (Chile); Bruzzone, H. [Pladema (Antiqua and Barbuda)]|[Univ. de Mar del Plata and CONICET (Argentina); Barbaglia, M. [Pladema (Antiqua and Barbuda); Mayer, R. [Pladema (Antiqua and Barbuda)]|[Inst. Balseiro, Bariloche, CNEA and CONICET (Argentina); Sidelnikov, Y.; Kies, W. [Heinrich-Heine-Univ., Duesseldorf (Germany)

2004-07-01

At present the Plasma Physics and Plasma Technology Group of the Comision Chilena de Energia Nuclear (CCHEN) has the experimental facilities in order to study dense transient discharges in a wide range of energy and current, namely: (I) energy from tens of joules to hundred of kilojoules, (II) current from tens of kiloamperes to some mega-amperes. Also several diagnostics have been implemented. An overview of the work being carried out on dense pinch discharges at the Comision Chilena de Energia Nuclear is presented. (orig.)

Research on pinch devices of tens of kA to MA

International Nuclear Information System (INIS)

Soto, L.; Silva, P.; Moreno, J.; Silvester, G.; Zambra, M.; Pavez, C.; Saavedra, R.; Bruzzone, H.; Barbaglia, M.; Mayer, R.; Sidelnikov, Y.; Kies, W.

2004-01-01

At present the Plasma Physics and Plasma Technology Group of the Comision Chilena de Energia Nuclear (CCHEN) has the experimental facilities in order to study dense transient discharges in a wide range of energy and current, namely: (I) energy from tens of joules to hundred of kilojoules, (II) current from tens of kiloamperes to some mega-amperes. Also several diagnostics have been implemented. An overview of the work being carried out on dense pinch discharges at the Comision Chilena de Energia Nuclear is presented. (orig.)

Pinch Related Research At Institute For Plasma Research, India

International Nuclear Information System (INIS)

Shyam, Anurag

2006-01-01

Several pinch related experiment, their drivers and related diagnostics are being developed in our laboratory. The first set of experiments is to investigate various aspects of magnetized target fusion (MTF/MAGO). To drive the liner, in Z or theta pinch configuration, a 1.2 MJ, 3.6 MA capacitor bank is developed. For liner diagnostics flash radiography, VISAR and pyrometery are being developed. To produce magnetized (target) plasma a 120 kJ, 3 MA and several other banks are developed. Hot magnetized Plasma will be diagnosed by optical schlieren, interferometery and X-Ray spectrometry. A terra-watt system consisting of a Marx bank and water line delivering 800 kA at 1.6 MV will be commissioned, soon. The device will be used to study different pinch (wire array) configurations for production of electro-magnetic radiations. Smaller pulsed power systems, consisting of 1MV/500 kV Marx bank/tesla transformer and than water or solid state (cables) pulse forming network (coax) are also being developed for capillary discharge and other experiments. Two plasma foci experiments are also being conducted. The effort is produce a repetitively operating compact plasma focus

Studies of end loss from a theta pinch using a Twyman--Green interferometer. Scientific report 77-4

International Nuclear Information System (INIS)

Freeman, R.S.

1977-11-01

The transient rate of flow of plasma from the ends of a short, high density, low temperature linear theta pinch was studied experimentally and analytically. Diagnostic devices were used to study the discharge and plasma properties; these included a Rogowski coil, a magnetic field probe and a Twyman-Green double pass interferometer which was illuminated by a 7 mW He--He laser. The interferometer was used to monitor the passage of fringes with respect to time at two radial positions simultaneously by the use of a photodetector consisting of two fast silicon photodiodes with supporting circuitry. One complete fringe represented a change in number density of 2.942 x 10 16 cm -3

The Rayleigh-Taylor instability in the spherical pinch

International Nuclear Information System (INIS)

Chen, H.B.; Hilko, B.; Panarella, E.

1994-01-01

The spherical pinch (SP) concept is an outgrowth of the inertial confinement model (ICF). Unlike the ICF where instabilities, especially the Rayleigh-Taylor instability, have been studied extensively, the instability study of the spherical pinch has just begun. The Raleigh-Taylor instability is investigated for the first time in the SP in the present work. By using the simple condition for the Rayleigh-Taylor instability ∇p · ∇p < O (density and pressure gradients have opposite direction), we have qualitatively identified the regions for development of instabilities in the SP. It is found that the explosion phase (central discharge) is stable and instabilities take place in the imploding phase. However, the growth rate for the instability is not in exponential form, and the appearance of the Rayleigh-Taylor instability does not prevent the main shock wave from converging to the center of the sphere

Dynamics of the plasma current sheath in plasma focus discharges in different gases

Energy Technology Data Exchange (ETDEWEB)

Vinogradov, V. P.; Krauz, V. I., E-mail: krauz-vi@nrcki.ru [National Research Center Kurchatov Institute (Russian Federation); Mokeev, A. N. [Project Center ITER (Russian Federation); Myalton, V. V.; Kharrasov, A. M. [National Research Center Kurchatov Institute (Russian Federation)

2016-12-15

The shape of the plasma current sheath (PCS) in the final stage of its radial compression, the dynamics of pinching, and the subsequent pinch decay in plasma focus (PF) discharges in different gases are studied using an improved multichannel system of electron-optical plasma photography and a newly elaborated synchronization system. The PCS structure in discharges in heavy gases (Ne, Ar) is found to differ significantly from that in discharges in hydrogen and deuterium. The influence of a heavy gas (Xe) additive to hydrogen and deuterium on the structure and compression dynamics of the PCS is investigated.

Characteristics of the TPE reversed-field pinch plasmas in conventional and improved confinement regimes

International Nuclear Information System (INIS)

Sakakita, H.; Asai, T.; Fiksel, G.; Yagi, Y.; Frassinetti, L.; Hayase, K.; Hirano, Y.; Kiyama, S.; Koguchi, H.; Shimada, T.; Innocente, P.; Spizzo, G.; Terranova, D.; Sato, Y.; Yoshikawa, M.

2005-01-01

We present the characteristics and experimental scaling laws of reversed-field pinch (RFP) plasmas, which are obtained from the recently established toroidal pinch experiment (TPE) database. The database contains information for approximately 1500 discharges consistently selected from four TPE RFP devices, and covers two decades of RFP experiments under conventional operating conditions at the National Institute of Advanced Industrial Science and Technology. We present the physics of the pulsed poloidal current drive (PPCD) discharges in the TPE-RX RFP device, and a comparison of the improved energy confinement time in PPCD, τ E P PCD , with τ E s caling as the reference scaling law (τ E s caling ∼ a 1.63 (I P 0.78 (I P /N) 0.33 Θ 2.97 ) in the TPE database, is attempted. The result shows that τ E P PCD agrees well with τ E s caling because of the strong pinch parameter dependence on the TPE scaling law. A potential improved confinement mode in the quasi-single-helicity (QSH) state is also investigated in TPE-RX, with respect to the operation conditions under which the QSH spontaneously appears in the core region, where a typical island structure is observed by means of soft Xray tomography. (author)

Fusion with Z-pinches

International Nuclear Information System (INIS)

Cook, D.

1998-06-01

In the past thirty-six months, great progress has been made in x-ray production using high-current z-pinches. Today, the x-ray energy and power output of the Z accelerator (formerly PBFA-II) is the largest available in the laboratory. These z-pinch x-ray sources have the potential to drive high-yield ICF reactions at affordable cost if several challenging technical problems can be overcome. In this paper, the recent technical progress with Z-pinches will be described, and a technical strategy for achieving high-yield ICF with z-pinches will be presented

Development of an effective pinch bar

CSIR Research Space (South Africa)

Ottermann, RW

2003-02-01

Full Text Available . ....................................10 Figure 3-3: Layout of lightweight pinch bar extruded fibreglass tube. ..................................11 Figure 3-4: XDM lightweight pinch bar with manufactured glass fibre bar. ..........................12 Figure 3-5: XDM lightweight pinch... bar with extruded glass fibre tube. ................................12 Figure 3-6: Stiffness of a 2.8m lightweight pinch bar with an extruded glass fibre tube and a 25mm steel pinch bar...

Particle acceleration and neutron production at the necks of plasma pinches

International Nuclear Information System (INIS)

Trubnikov, B.A.

1986-01-01

Induction electric fields are shown to arise in a deuterium plasma pinch because of a redistribution of the current over the discharge cross section. These fields accelerate deuterons, which produce neutrons. The total current I 0 is assumed to be constant but to consist of two components: I 0 = I 1 +I 2 , where K 1 (t) is a decaying current in the main pinch, and I 2 (t) is an increasing current in the peripheral plasma around the pinch. The current I 1 produces fields B = 2I 1 /cr and E = I 1 c -2 ln(r/R) 2 , where R is some length. The current I 1 is assumed to fall off so rapidly that the deuterons of the peripheral plasma are not ''coiled'' by the magnetic field. They acquire a velocity v = (e/M) ∫ E dt = v/sub */ ln(R/r) 2 , where v/sub */ = eI 0 /Mc 2 , in an impulsive fashion. The functional dependence r 2 = R 2 exp(-v/v/sub */) follows

Energy- and particle-confinement properties of an end-plugged, linear, theta pinch

International Nuclear Information System (INIS)

Commisso, R.J.; Bartsch, R.R.; Ekdahl, C.A.; McKenna, K.F.; Siemon, R.E.

1979-01-01

Experiments show that axial confinement of plasma in a straight theta-pinch solenoid is improved by placing solid lithium deuteride plugs at the ends. The energy confinement is increased nearly threefold in agreement with theoretical estimates which assume classical electron thermal conduction and no convective losses. The confinement of deuterium ions is explained by classical Coulomb collisions in the ablated lithium deuteride plasma

X-ray emission from a high-atomic-number z-pinch plasma created from compact wire arrays

International Nuclear Information System (INIS)

Sanford, T.W.L.; Mosher, D.; De Groot, J.S.

1996-01-01

Thermal and nonthermal x-ray emission from the implosion of compact tungsten wire arrays in 5-MA Saturn discharges is reported. The timing of multiple implosions and the thermal x-ray spectra (1 to 10 keV) agree with 2D radiation-hydrocode simulations. Nonthermal x-ray emission (10 to 100 keV) correlates with pinch spots distributed along the z-axis. The similarities of the measured nonthermal spectrum, yield, and pinch-spot emission with those of 0.8-MA, single-exploded-wire discharges on Gamble-II suggest a common nonthermal-production mechanism. Nonthermal x-ray yields are lower than expected from current scaling of Gamble II results, suggesting that implosion geometries are not as efficient as single-wire geometries for nonthermal x-ray production. The instabilities, azimuthal asymmetries, and inferred multiple implosions that accompany the implosion geometry lead to larger, more irregular pinch spots, a likely reason for reduced nonthermal efficiency. A model for nonthermal-electron acceleration across magnetic fields in highly-collisional, high-atomic-number plasmas combined with 1D hydrocode simulations of Saturn compact loads predicts weak nonthermal x-ray emission. (author). 3 figs., 10 refs

X-ray emission from a high-atomic-number z-pinch plasma created from compact wire arrays

International Nuclear Information System (INIS)

Sanford, T.W.L.; Mosher, D.; De Groot, J.S.

1996-01-01

Thermal and nonthermal x-ray emission from the implosion of compact tungsten wire arrays in 5-MA Saturn discharges is reported. The timing of multiple implosions and the thermal x-ray spectra (1 to 10 keV) agree with 2D radiation-hydrocode simulations. Nonthermal x-ray emission (10 to 100 keV) correlates with pinch spots distributed along the z-axis. The similarities of the measured nonthermal spectrum, yield, and pinch-spot emission with those of 0.8-MA, single- exploded-wire discharges on Gamble-II suggest a common nonthermal- production mechanism. Nonthermal x-ray yields are lower than expected from current scaling of Gamble II results, suggesting that implosion geometries are not as efficient as single-wire geometries for nonthermal x-ray production. The instabilities, azimuthal asymmetries, and inferred multiple implosions that accompany the implosion geometry lead to larger, more irregular pinch spots, a likely reason for reduced nonthermal efficiency. A model for nonthermal-electron acceleration across magnetic fields in highly- collisional, high-atomic-number plasmas combined with 1D hydrocode simulations of Saturn compact loads predicts weak nonthermal x-ray emission

Warm dense matter study and pulsed-power developments for X-pinch equipment in Nagaoka University of Technology

International Nuclear Information System (INIS)

Sasaki, Toru; Miki, Yasutoshi; Tachinami, Fumitaka; Saito, Hirotaka; Takahashi, Takuya; Anzai, Nobuyuki; Kikuchi, Takashi; Aso, Tsukasa; Harada, Nob.

2014-01-01

In order to explore high energy density physics, we have performed WDM experiment by using several pulsed-power devices. To generate well-defined warm dense state for evaluating electrical conductivity and its properties, we have proposed an isochoric heating of foamed metal by using pulsed-power discharge. The proposed technique yields the electrical conductivity of warm dense matter with a well-defined temperature. To observe the warm dense matter, a pulsed-power generator based on a pulse-forming-network (PFN) was studied toward generating an intense point-spot-like X-ray source from X-pinch technique. From comparison of the designing and the actual inductances of the X-pinch system, the actual inductance of X-pinch system is 3.5 times higher than the designing inductance. To reduce the total inductance of X-pinch system, we will modify the gap switch system such as multi spake gap

The stability of the High-Density Z-Pinch

International Nuclear Information System (INIS)

Glasser, A.H.; Nebel, R.A.

1989-01-01

Fiber-initiated High Density Z-Pinches at Los Alamos, NRL, and Karlsruhe have shown anomalously good stability. Kink modes are never seen, and sausage modes are at least delayed until late in the discharge. The success of these devices in reaching fusion conditions may depend on maintaining and understanding this anomalous stability. We have developed two numerical methods to study the stability in the regime where fluid theory is valid. While our methods are applicable to all modes, we will describe them only for the m = 0 sausage mode. The appearance of sausage modes late in the discharge and the total absence of kink modes suggest that an understanding of sausage modes is more urgent, and it is also simpler. 14 refs., 8 figs

The stability of the high-density z-pinch

International Nuclear Information System (INIS)

Glasser, A.H.; Nebel, R.A.

1989-01-01

Fiber-initiated High Density Z-Pinches at Los Alamos, NRL, and Karlsruhe have shown anomalously good stability. Kink modes are never seen, and sausage modes are at least delayed until late in the discharge. The success of these devices in reaching fusion conditions may depend on maintaining and understanding this anomalous stability. We have developed two numerical methods to study the stability in the regime where fluid theory is valid. While our methods are applicable to all modes, we will describe them only for the m=0 sausage mode. The appearance of sausage modes late in the discharge and the total absence of kink modes suggest that an understanding of sausage modes is more urgent, and it is also simpler

Plasma-wall interaction and locked modes in the toroidal pinch experiment TPE-RX reversed-field pinch

International Nuclear Information System (INIS)

Pasqualini, D.; Martin, P.; Koguchi, H.; Yagi, Y.; Hirano, Y.; Sakakita, H.; Spizzo, G.

2006-01-01

The MHD instabilities that sustain the reversed-field pinch (RFP) configuration tend to phase-lock together and also to wall-lock, forming a bulging of the plasma column, called 'locked mode'. This phenomenon is of particular interest, since the locked mode causes a larger plasma resistivity, plasma cooling, and, in some cases, anomalous discharge termination. Up to now, studies of the locked mode have been focused on m=1 modes (being m the poloidal mode number). In this Letter we show that m=0 modes also play a role, based on the cross-check between magnetic spectra and toroidally resolved D α array measurements. (author)

The UNICAMP theta-pinch for spectroscopic study of plasma radiations

International Nuclear Information System (INIS)

Trigueiros, A.G.; Luna, F.R.T.; Holanda Cavalcanti, G. de; Mania, A.J.

1993-01-01

The emission spectrum of six times ionized xenon (Xe VII), has been observed in the vacuum ultraviolet (VUV) using a theta-pinch discharge. The spectrum was recorded with a 2-meter normal incidence spectrograph in the 300-2000 A region. Preliminary results allow the identification of transitions in the n=5 complex. Ten of these transitions were identified. The identifications are supported by relativistic Hartree-Fock calculations. (author)

Development of Z-pinch optical guiding for laser-plasma accelerator

International Nuclear Information System (INIS)

Hosokai, Tomonao; Kando, Masaki; Dewa, Hideki; Kotaki, Hideyuki; Kondo, Shuji; Kanazawa, Shuhei; Nakajima, Kazuhisa; Horioka, Kazuhiko

2000-01-01

We have proposed optical guiding of intense laser pulse by fast Z-pinch for channel guided laser wakefield acceleration (LWFA). It has been developed based on capillary discharge-pumped X-ray laser technique. The discharge driven by current of 4.8 kA with a rise time of 15 ns through preionized helium gas could produce an uniform guiding channel with good reproducibility. With this new guiding method an intense Ti-Sapphire laser pulse (λ=790 nm, 2.2 TW, 90 fs, 1 x 10 17 W/cm 2 ) was transported through the channel over a distance of 2 cm corresponding to 12.5 times the Rayleigh length. (author)

Three-fluid MHD-model of a current shell in Z-pinch

International Nuclear Information System (INIS)

Bazdenkov, S.V.; Vikhrev, V.V.

1975-01-01

Formation and motion of the current shell in a power pulsed discharge (Z-pinch) are discussed. One-dimmensional nonstationary problem about a discharge in deuterium is solved in the three-liquid magnetohydrodynamic approximation with regard for gas ionization and motion of neutral atoms. It is shown that after the shell removal there remains a large quantity of an ionized gas near an isolating chamber wall. The quantity is sufficient that a secondary breakdown may take place in the ionized gas. The moving current shell has a double structure, i.e. a current ''piston'' and a current layer in the shock wave front

Reconsideration of the m=0 Z-pinch stability

International Nuclear Information System (INIS)

Scheffel, J.; Coppins, M.

1993-01-01

Possible paths for obtaining linear stability against the m=0 mode in the Z-pinch are studied. Using a generalized energy principle, the necessary and sufficient Chew-Goldberger-Low (CGL) m=0 stability criterion is derived. This criterion is less restrictive than that of ideal MHD, although it also requires the boundary plasma pressure to be finite. It is shown that the edge pressure cannot be stably upheld by a surface current. By instead assuming a finite pressure external gas, it is found that an edge pressure to on-axis pressure ratio of 0.5 is required for stability of a constant current density profile. A parabolic current density profile lowers the limit to the value 0.17. The growth rates are shown to be monotonically decreasing as a function of the external gas pressure. Detailed derivations of the boundary conditions are also given. The results aid in clarifying the experimental stability of four major Z-pinch experiments. Finite Larmor radius stabilization is hence required to maintain stability in future fibre pinch experiments in vacuum, implying line densities less than 10 19 m -1 . (author). 28 refs, 10 figs

Helical-D pinch

International Nuclear Information System (INIS)

Schaffer, M.J.

1997-08-01

A stabilized pinch configuration is described, consisting of a D-shaped plasma cross section wrapped tightly around a guiding axis. The open-quotes helical-Dclose quotes geometry produces a very large axial (toroidal) transform of magnetic line direction that reverses the pitch of the magnetic lines without the need of azimuthal (poloidal) plasma current. Thus, there is no need of a open-quotes dynamoclose quotes process and its associated fluctuations. The resulting configuration has the high magnetic shear and pitch reversal of the reversed field pinch (RFP). (Pitch = P = qR, where R = major radius). A helical-D pinch might demonstrate good confinement at q << 1

A reversed-field theta-pinch plasma machine

International Nuclear Information System (INIS)

Yasojima, Yoshiyuki; Ueda, Yoshihiro; Sasao, Hiroyuki; Ueno, Noboru; Tanaka, Toshihide

1984-01-01

Mitsubishi Electric has constructed a reversed-field theta-pinch machine at its Central Research Laboratory and initiated a series of plasma diagnostics and control studies for development of nuclear-fusion technology. Although the device has a linear configuration, a stable high-temperature, high-density toroidal plasma can be generated. The article describes the overall structure, vacuum system, power-supply system, and diagnostics and control system of the plasma machine. (author)

Necessary stability condition for field-reversed theta pinches

International Nuclear Information System (INIS)

Cary, J.R.

1981-03-01

Toroidal systems of arbitrary cross section without toroidal magnetic field are analyzed via the double adiabatic fluid equations. Such systems are shown to be unstable if there exists one closed field line on which the average of kapparB 2 is positive, where kappa is the curvature. A similar criterion is derived for linear systems and is applied to a noncircular z-pinch

Development of fast pulsed power driver for radiography and Z-pinch

International Nuclear Information System (INIS)

Qiu Aici; Sun Fengju

2008-01-01

Z-pinch and flash X-ray radiography have an important application in inertial confine fusion (ICF) and nuclear radiation effects simulation and high performance hydrodynamic test, etc. Z-pinch ICF and multi-pulse multi-axis high energy X-ray radiography put forward a huge challenge for pulsed power driver, so the direct-driven-load fast pulsed power driver are developed actively in home and abroard. The paper summarized the recent advances and developing trends of the fast pulsed power driver based on fast Marx(FMG) and fast linear transformer driver (LTD), and analysized the advantages and disadvantages and restricting factors about FMG and FLTD and their key technologies, then introduced the state-of-arts on the investigation in Northwest Institute of Nuclear Technology. In the end, the paper presented some advices and views about studying fast pulsed power driver applied to Z-pinch and flash X-ray radiography in home. (authors)

Analysis of staged Z-pinch implosion trajectories from experiments on Zebra

Science.gov (United States)

Ross, Mike P.; Conti, F.; Darling, T. W.; Ruskov, E.; Valenzuela, J.; Wessel, F. J.; Beg, F.; Narkis, J.; Rahman, H. U.

2017-10-01

The Staged Z-pinch plasma confinement concept relies on compressing an annular liner of high-Z plasma onto a target plasma column of deuterium fuel. The interface between the liner and target is stable against the Magneto-Rayleigh-Taylor Instability, which leads to effective fuel compression and makes the concept interesting as a potential fusion reactor. The liner initiates as a neutral gas puff, while the target plasma is a partially ionized (Zeff coaxial plasma gun. The Zebra pulsed power generator (1 MA peak current, 100 ns rise time) provides the discharge that ionizes the liner and drives the Z-pinch implosion. Diverse diagnostics observe the 100-300 km/s implosions including silicon diodes, photo-conducting detectors (PCDs), laser shadowgraphy, an XUV framing camera, and a visible streak camera. The imaging diagnostics track instabilities smaller than 0.1 mm, and Z-pinch diameters below 2.5 mm are seen at peak compression. This poster correlates the data from these diagnostics to elucidate implosion behavior dependencies on liner gas, liner pressure, target pressure, and applied, axial-magnetic field. Funded by the Advanced Research Projects Agency - Energy, DE-AR0000569.

Stability analysis of sharp-boundary Vlasov-fluid screw-pinch equilibria

International Nuclear Information System (INIS)

Lewis, H.R.; Turner, L.

1975-01-01

The Vlasov-fluid model is being used to study the linear stability of sharp-boundary screw pinches numerically. The numerical method appears to work well, and some preliminary results are reported. The sharp-boundary calculation is useful for gaining insight and for comparing with known MHD results. (auth)

Z-pinches

International Nuclear Information System (INIS)

Yan'kov, V.V.

1991-01-01

The development of Z-pinches, including plasma foci, micropinches and dense Z-pinches are reviewed. A special attention is paid to the physics of sausage instability development. Theoretical questions are discussed in more detail that the experimental ones, recent works - to a fuller extent than the fundamental pioneer ones which are included in the textbooks. The Soviet works are given a greater coverage as compared to the foreign ones. An emphasis is made on the problem of controlled thermonuclear fusion

Observation of visible emission from the molecular helium ion in the afterglow of a dense helium Z-pinch plasma

International Nuclear Information System (INIS)

Tucker, J.E.; Brake, M.L.; Gilgenbach, R.M.

1986-01-01

The authors present the results of axial and radial time resolved visible emission spectroscopy from the afterglow of a dense helium Z-pinch. These results show that the visible emissions in the pinch afterglow are dominated by line emissions from molecular helium and He II. Axial spectroscopy measurements show the occurrence of several absorption bands which cannot be identified as molecular or atomic helium nor impurities from the discharge chamber materials. The authors believe that these absorption bands are attributable to the molecular helium ion which is present in the discharge. The molecular ion has been observed by others in low pressure and temperature helium discharges directly by means of mass spectrometry and indirectly by the presence of helium atoms in the 2/sup 3/S state, (the He 2/sup 3/S state is believed to result from molecular helium ion recombination). However, the molecular helium ion has not previously been observed spectroscopically

Magnetoacoustic heating and FCT-equilibria in the belt pinch

International Nuclear Information System (INIS)

Erckmann, V.

1983-02-01

In the HECTOR belt pinch of high β plasma is produced by magnetic compression in a Tokamak geometry. After compresseion the initial β value can be varied between 0.2 and 0.8. During 5 μs the plasma is further heated by a fast magnetoacoustic wave with a frequency near the first harmonic of the ion cyclotronfrequency. For the first time the β-value of a pinch plasma could be increased further from 0.34 after compression to 0.46 at the end of the rf-heating cycle. By proper selection of the final β-value the region for resonance absorption of the heating wave can be shifted. Strong heating (200 MW) has been observed in the cases, where the resonance region has been located in the center of the plasma. In deuterium discharges an increase in ion temperature is observed during the heating process, whereas the electrons are energetically decoupled, showing no temperature increase. Strong plasma losses are found in the 200 MW range after the rf-heating process. The dominant mechanisms are charge exchange collisions with neutral gas atoms. During rf-heating and the subsequent cooling phase the magnetic flux is frozen due to the high conductivity of the plasma. The observed equilibria could be identified as flux conserving Tokamak (FCT) equilibria. Based on a two-dimensional code the time-evolution of the equilibria has been calculated. The q-profiles are time-independent, with increasing β the magnetic axis of the plasma is shifted towards the outer boundary of the torus, and finally the linear relation between β and βsub(pol), which is characteristic for low-β-equilibria, is no longer valid. Thus for the first time the existence of FCT-equilibria at high β has been demonstrated experimentally together with a qualitative agreement with FCT-theory. (orig./AH) [de

The formation of metallic plasmas in transient capillary discharges at high current

International Nuclear Information System (INIS)

Wyndham, E S; Favre, M; Aliaga-Rossel, R

2006-01-01

We report observations of the formation of a metallic plasma in a high aspect ratio z-pinch confined within a ceramic capillary. A series of experiments on different capillary geometries was undertaken in which titanium metal rings were used to promote the formation of a titanium plasma through preferential ablation. In an initial vacuum a titanium seed plasma is formed in the hollow cathode (HC) volume by a low energy laser spark. This pre-ionizing plasma is assisted in its expansion into the z-pinch volume by the electron beams generated by a pre-ionizing discharge in the capillary, due to the HC effect. Further intense e-beam activity occurs on applying the main driver current to the capillary electrodes before the discharge impedance abruptly drops to give rise to an ensuing high current z-pinch. A segmented titanium ring structure within the capillary promotes metal ablation. The discharges are performed in tubes of 60 to 110 mm length and 3 and 5 mm effective internal diameter. The main discharge current is provided from a small pulsed power switched coaxial line, at up to 150 kA. The generator may be configured to deliver two different rates of current rise and this is found to have a significant effect on the plasma dynamics. The plasma properties are obtained from observations of the axial x-ray emission. The diagnostics used are filtered Si diodes, filtered time-resolved multi-pinhole camera images and the time resolved soft x-ray spectrum from 3 to 20 nm. While a single species metal plasma is not obtained, a very significant proportion of Ti is achieved in the higher rate of current rise configuration. The fraction of Ti diminishes for the longest length discharges and for the larger diameter tube diameter, as does the observed z-pinch uniformity. There is a weak dependance of the electron temperature with tube geometry, but the plasma density falls substantially in the longer discharges. This coincides with diminished effectiveness of the transient HC

High brightness extreme ultraviolet (at 13.5 nm) emission from time-of-flight controlled discharges with coaxial fuel injection

International Nuclear Information System (INIS)

Hosokai, Tomonao; Horioka, Kazuhiko; Hotta, Eiki; Yokoyama, Takuma; Sato, Hiroto; Zhidkov, Alexei

2008-01-01

Extreme ultraviolet (EUV) emission from discharge produced plasma with the coaxial injection of fuel vapor (tin and lithium) produced by laser ablation is experimentally studied. Multiple plasma pinches preceding a strong and long recombination radiation of EUV are observed in the first half cycle of a sinusoidal discharge current. Due to the time-of-flight control type of the discharge, the shape of pinch radiation pulses is almost identical. With the coaxial injection of time-of-flight controlled discharges, the highest brightness of EUV emission (maximum extracted energy of 244.3 mJ/2π sr per pulse with the emitter size of ∼1x0.3 mm 2 in full width at half maximum) is provided with efficiency exceeding 2% of deposited energy into the plasma (or 1% of dissipated energy in the discharge) due to a much better matching with the optimal plasma parameters in the recombination regime and a decrease in the off-duty factor. Stability of emitting plasma of the repetitive pinches is essentially improved with use of a second laser pulse

Finite Larmor radius effects on Z-pinch stability

International Nuclear Information System (INIS)

Scheffel, J.; Faghihi, M.

1987-10-01

The effect of finite Larmor radius (FLR) on the stability of m=1 small axial wavelength kinks in a z-pinch with purely poloidal magnetic field is investigated. We use the Incompressible FLR MHD model; a collisionless fluid model which consistently includes the relevant FLR terms due to ion gyroviscosity, Hall effect and electron diamagnetism. With FLR terms absent, the Kadomtsev criterion of ideal MHD 2rdp/dr+m 2 B 2 /μ 0 >=0 predicts instability for internal modes unless the current density becomes singular at the centre of the pinch. The same result is obtained in the present model, with FLR terms absent. When the FLR terms are included, a normal mode analysis of the linearized equations yields the following results. Marginally unstable (ideal) modes are stabilized by gyroviscosity. The Hall terms have a damping, however not stabilizing, effect, in agreement with earlier work. Specifying a constant current and particle density equilibrium, the effect of electron diamagnetism vanishes. For a z-pinch with parameters relevant to the EXTRAP experiment, the m=1 modes are then fully stabilized over the cross-section for wavelengths λ/a max =3-5x10 18 m -1 is found, above which gyroviscous stabilization near the plasma boundary becomes insufficient. The result holds for wavelengths close to, or smaller than, the pinch radius and for realistic equilibrium profiles. This limit is far below the required limit for a reactor with contained alpha particles, which is in excess of 10 20 m -1 . (authors)

Flow discharge prediction in compound channels using linear genetic programming

Science.gov (United States)

Azamathulla, H. Md.; Zahiri, A.

2012-08-01

SummaryFlow discharge determination in rivers is one of the key elements in mathematical modelling in the design of river engineering projects. Because of the inundation of floodplains and sudden changes in river geometry, flow resistance equations are not applicable for compound channels. Therefore, many approaches have been developed for modification of flow discharge computations. Most of these methods have satisfactory results only in laboratory flumes. Due to the ability to model complex phenomena, the artificial intelligence methods have recently been employed for wide applications in various fields of water engineering. Linear genetic programming (LGP), a branch of artificial intelligence methods, is able to optimise the model structure and its components and to derive an explicit equation based on the variables of the phenomena. In this paper, a precise dimensionless equation has been derived for prediction of flood discharge using LGP. The proposed model was developed using published data compiled for stage-discharge data sets for 394 laboratories, and field of 30 compound channels. The results indicate that the LGP model has a better performance than the existing models.

Introduction to Pinch Technology

DEFF Research Database (Denmark)

Rokni, Masoud

? How to put energy efficiency and other targets like reducing emissions, increasing plant capacities, improve product qualities etc, into a one coherent strategic plan for the overall site? All these questions and more can be answered with a full understanding of Pinch Technology and an awareness...... of the available tools for applying it in a practical way. The aim here is to provide the basic knowledge of pinch technology concept and how it can be applied across a wide range of process industries. The pinch technology was proposed firstly for optimization of heat exchangers and therefore it is introduced...

High density linear systems for fusion power

International Nuclear Information System (INIS)

Ellis, W.R.; Krakowski, R.A.

1975-01-01

The physics and technological limitations and uncertainties associated with the linear theta pinch are discussed in terms of a generalized energy balance, which has as its basis the ratio (Q/sub E/) of total electrical energy generated to net electrical energy consumed. Included in this total is the virtual energy of bred fissile fuel, if a hybrid blanket is used, as well as the actual of real energy deposited in the blanket by the fusion neutron. The advantages and disadvantages of the pulsed operation demanded by the linear theta pinch are also discussed

Characterization of laser-cut copper foil X-pinches

Science.gov (United States)

Collins, G. W.; Valenzuela, J. C.; Hansen, S. B.; Wei, M. S.; Reed, C. T.; Forsman, A. C.; Beg, F. N.

2016-10-01

Quantitative data analyses of laser-cut Cu foil X-pinch experiments on the 150 ns quarter-period, ˜250 kA GenASIS driver are presented. Three different foil designs are tested to determine the effects of initial structure on pinch outcome. Foil X-pinch data are also presented alongside the results from wire X-pinches with comparable mass. The X-ray flux and temporal profile of the emission from foil X-pinches differed significantly from that of wire X-pinches, with all emission from the foil X-pinches confined to a ˜3 ns period as opposed to the delayed, long-lasting electron beam emission common in wire X-pinches. Spectroscopic data show K-shell as well as significant L-shell emission from both foil and wire X-pinches. Fits to synthetic spectra using the SCRAM code suggest that pinching foil X's produced a ˜1 keV, ne ≥ 1023 cm-3 plasma. The spectral data combined with the improved reliability of the source timing, flux, and location indicate that foil X-pinches generate a reproducible, K-shell point-projection radiography source that can be easily modified and tailored to suit backlighting needs across a variety of applications.

Microinstabilities and turbulent transport in the reversed field pinch

Science.gov (United States)

Carmody, Daniel Richard

The work presented in this thesis is concerned with addressing the nature of drift wave microturbulence in the reversed field pinch (RFP). Microturbulence is an important phenomenon and contributor to heat and particle transport in tokamaks, where it has been studied for several decades, but its role in the RFP is a rather new topic of study. As such, the nature of RFP drift waves and their relationship to their tokamak counterparts is still developing, and many of the results in this work are focused on addressing this challenge. Fundamental advances in microturbulence research have been made in recent decades through two parallel developments: the theoretical framework encompassed in the gyrokinetic model, and the computational power offered by massively-parallel, high-performance computing systems. Gyrokinetics is a formulation of kinetic theory in such a way that the fast timescale gyromotion of particles around magnetic field lines is averaged out. The implementation and use of RFP equilibrium models in gyrokinetic codes constitutes the bulk of this thesis. A simplified analytic equilibrium, the toroidal Bessel function model (TBFM), is used in the gyrokinetic code GYRO to explore the fundamental scaling properties of drift waves in the RFP geometry. Two drift wave instabilities, the ion temperature gradient (ITG) mode and the microtearing mode (MTM) are found to occur, and the relationship of their critical threshold in driving gradients and plasma beta is explored. The critical values in these parameters are found to be above those of similar tokamak cases by roughly a factor of the flux surface aspect ratio. The MTM is found to be stabilized by increasing the RFP pinch parameter theta, making it unlikely for it to unstable in the high-theta improved confinement pulsed poloidal current drive (PPCD) discharges. Efforts are also made to address microinstabilities in specific experimental discharges of the Madison Symmetric Torus (MST). A semi

Linear studies of resistive interchange modes in a cylindrical reversed field pinch

International Nuclear Information System (INIS)

Mirin, A.A.; O'Neill, N.J.; Killeen, J.; Bonugli, R.J.; Ellis, M.J.

1986-01-01

Resistive interchange modes in a cylindrical reversed field pinch are studied using a one-dimensional, linear, compressible initial value code. Separate equations for the electron and ion temperature perturbations are solved. Hall terms and the thermal force vector are included in Ohm's law. Anisotropic thermal conductivity and viscosity are included in the code model. Calculations are carried out for various values of poloidal and toroidal mode number, Lundquist number, Suydam parameter, Hall parameter, thermal conductivity, viscosity, etc., with respect to uniform density equilibria known to be stable to tearing modes. It is shown that in the cold ion limit sufficiently large Hall terms cause all modes that are tested to become stable. However for T/sub i/ = T/sub e/ and ignoring the effects of viscosity and thermal conductivity, there is a critical value of the ratio of Alfven to ion cyclotron frequency above which the ''even'' mode not only dominates the ''odd'' mode but is likely to have a growth rate significantly larger than that of the odd mode in the absence of Hall terms. Inclusion of a classical tensor thermal conductivity, while having little effect on the odd mode in the absence of Hall terms, does stabilize the even mode for sufficiently large Hall parameter. Inclusion of a classical tensor viscosity reduces the growth rate of (but does not necessarily stabilize) the odd mode. Inclusion of Hall and thermal force terms, tensor thermal conductivity and tensor viscosity causes all modes that are tested to stabilize. Results are compared to other contemporary studies

Measurements of high-current electron beams from X pinches and wire array Z pinches

International Nuclear Information System (INIS)

Shelkovenko, T. A.; Pikuz, S. A.; Blesener, I. C.; McBride, R. D.; Bell, K. S.; Hammer, D. A.; Agafonov, A. V.; Romanova, V. M.; Mingaleev, A. R.

2008-01-01

Some issues concerning high-current electron beam transport from the X pinch cross point to the diagnostic system and measurements of the beam current by Faraday cups are discussed. Results of computer simulation of electron beam propagation from the pinch to the Faraday cup give limits for the measured current for beams having different energy spreads. The beam is partially neutralized as it propagates from the X pinch to a diagnostic system, but within a Faraday cup diagnostic, space charge effects can be very important. Experimental results show evidence of such effects.

Cryogenic deuterium Z-pinch and wire array Z-pinch studies at Imperial College

International Nuclear Information System (INIS)

Haines, M.G.; Aliaga-Rossel, R.; Beg, N.F.

2001-01-01

Z-pinch experiments using cryogenic deuterium fibre loads have been carried out on the MAGPIE generator at currents up to 1.4MA. M=0 instabilities in the corona caused plasma expansion and disruption before the plasma could enter the collisionless Large ion Larmor radius regime. For the last 12 months we have studied Aluminium wire array implosions using laser probing, optical streaks and gated X-ray images. Plasma from the wires in accelerated to the axis as radial plasma streams with uncorrelated m=0 instabilities superimposed. Later in the discharge a global Rayleigh-Taylor (R-T) instability develops. Single and double aluminium and tungsten wire shots were conducted at 150kA. 2-D and 3-D simulations and a heuristic model of wire arrays will be presented along with theories on the combined MHD/R-T instability and sheared axial flow generation by large ion Larmor radius effects. (author)

Cryogenic deuterium Z-pinch and wire array Z-pinch studies at imperial college

International Nuclear Information System (INIS)

Haines, M.G.; Aliaga-Rossel, R.; Beg, F.N.

1999-01-01

Z-pinch experiments using cryogenic deuterium fibre loads have been carried out on the MAGPIE generator at currents up to 1.4MA. M=0 instabilities in the corona caused plasma expansion and disruption before the plasma could enter the collisionless Large ion Larmor radius regime. For the last 12 months we have studied Aluminium wire array implosions using laser probing, optical streaks and gated X-ray images. Plasma from the wires in accelerated to the axis as radial plasma streams with uncorrelated m=0 instabilities superimposed. Later in the discharge a global Rayleigh-Taylor (R-T) instability develops. Single and double aluminium and tungsten wire shots were conducted at 150kA. 2-D and 3-D simulations and a heuristic model of wire arrays will be presented along with theories on the combined MHD/R-T instability and sheared axial flow generation by large ion Larmor radius effects. (author)

Lower pinch radius limit in EXTRAP

International Nuclear Information System (INIS)

Lehnert, B.

1989-01-01

In an Extrap pinch there is a superimposed magnetic octupole field which forms a magnetic separatrix with the field generated by the pinch current. Earlier experiments have shown that the octupole field has a stabilizing influence on the plasma. Regardless of the details of this stabilizing mechanism, it is expected that the influence of the octupole field should become negligible for a sufficiently small ratio between the characteristic pinch and separatrix radii. In other words, there should exist a lower limit of this ratio below which the system approaches the state of an ordinary unstabilized Z-pinch. The present paper presents an extended version of an earlier theoretical model of this lower limit, and its relation to the corresponding critical ratio between the external conductor and pinch currents. This ratio is found to vary substantially with the plasma parameters. (authors)

Confinement in TPE-RX reversed field pinch

International Nuclear Information System (INIS)

Yagi, Y.; Bolzonella, T.; Canton, A.

2001-01-01

Characteristics of the confinement properties of a reversed field pinch (RFP), the TPE-RX (R/a=1.72/0.45 m, R and a are major and minor radii), are presented for the plasma current, I p of 0.2-0.4 MA. TPE-RX has been operational since 1998, and I p =0.5 MA and duration time of up to 0.1 s have been obtained separately. It is found that I p /N (=12x10 -14 Am, N is the line density) is higher than those of other RFPs and poloidal beta, β p , and energy confinement time, τ E , are 5-10% and 0.5-1 ms, respectively, which are comparable with those of other RFPs of comparable sizes (RFX and MST). Pulsed poloidal current drive has recently been tested and the result has shown a twofold improvement of β p and τ E . The improvement is discussed in terms of the dynamic trajectories in the F-Θ plane, where F and Θ are reversal and pinch parameters, respectively. The global confinement properties are compared between the locked and non-locked discharges, which yields a better understanding of the mode-locking phenomena in RFP plasmas. (author)

Reversed-Field Pinch plasma model

International Nuclear Information System (INIS)

Miley, G.H.; Nebel, R.A.; Moses, R.W.

1979-01-01

The stability of a Reversed-Field Pinch (RFP) is strongly dependent on the plasma profile and the confining sheared magnetic field. Magnetic diffusion and thermal transport produce changing conditions of stability. Despite the limited understanding of RFP transport, modelling is important to predict general trends and to study possible field programming options. To study the ZT-40 experiment and to predict the performance of future RFP reactors, a one-dimensional transport code has been developed. This code includes a linear, ideal MHD stability check based on an energy principle. The transport section integrates plasma profiles forward in time while the stability section periodically checks the stability of the evolving plasma profile

Study of soft X-ray energy spectra from gas-puff Z-pinch plasma

International Nuclear Information System (INIS)

Zou Xiaobing; Wang Xinxin; Zhang Guixin; Han Min; Luo Chengmu

2006-01-01

A ROSS-FILTER-PIN spectrometer in the spectral range of 0.28 keV-1.56 keV was developed to study the soft X-ray radiation emitted from gas-puff Z-pinch plasma. It is composed of five channels covering the energy interval of interest without gaps. Soft X-ray spectral energy cuts were determined by the L absorption edges of selected filter elements (K absorption edges being used for light filter elements), and the optimum thickness of filter material was designed using computer code. To minimize the residual sensitivity outside the sensitivity range of each channel, element of the first filter was added into the second filter of all the Ross pair. To diminish the area of each filter, PIN detector with small sensitive area of 1 mm 2 was adopted for the spectrometer. A filter with small area is easy to fabricate and would be helpful to withstand the Z-pinch discharge shock wave. With this ROSS-FILTER-PIN spectrometer, the energy spectra of soft X-ray from a small gas-puff Z-pinch were investigated, and the correlation between the soft X-ray yield and the plasma implosion state was also studied. (authors)

Analysis of pinching in deterministic particle separation

Science.gov (United States)

Risbud, Sumedh; Luo, Mingxiang; Frechette, Joelle; Drazer, German

2011-11-01

We investigate the problem of spherical particles vertically settling parallel to Y-axis (under gravity), through a pinching gap created by an obstacle (spherical or cylindrical, center at the origin) and a wall (normal to X axis), to uncover the physics governing microfluidic separation techniques such as deterministic lateral displacement and pinched flow fractionation: (1) theoretically, by linearly superimposing the resistances offered by the wall and the obstacle separately, (2) computationally, using the lattice Boltzmann method for particulate systems and (3) experimentally, by conducting macroscopic experiments. Both, theory and simulations, show that for a given initial separation between the particle centre and the Y-axis, presence of a wall pushes the particles closer to the obstacle, than its absence. Experimentally, this is expected to result in an early onset of the short-range repulsive forces caused by solid-solid contact. We indeed observe such an early onset, which we quantify by measuring the asymmetry in the trajectories of the spherical particles around the obstacle. This work is partially supported by the National Science Foundation Grant Nos. CBET- 0731032, CMMI-0748094, and CBET-0954840.

Model of emittance growth in a self-pinched beam

International Nuclear Information System (INIS)

Lee, E.P.; Yu, S.S.

1979-01-01

A semi-phenomenological formula is proposed for the change of emittance of a self-pinched beam which is not matched to its equilibrium radius. Near equilibrium this formula, coupled with an envelope equation, yields the damped sausage oscillations observed in simulation and experiments. For a beam which is injected cold (no transverse velocity spread), the formula coincides with the analytically calculated initial growth of emittance. The basic theory is developed here and used to compute the linear damping rate for several current profiles. The resultant non-linear increase in equilibrium quantities is also calculated in lowest order of the degree of mismatch

The IGBT as an element of switch discharge with a linear mode use in capacitor discharge power converters

CERN Document Server

Cravero, J M

1998-01-01

This paper presents an unusual use of IGBT (Insulated Gate Bipolar Transistor) modules in capacitor discharge power supplies to achieve different current pulse shapes. The new power converters are described with an emphasis on the use of the IGBT as a discharge switch or in a linear mode. The difficulties involved in implementing IGBTs in these modes are analysed. IGBT voltage and gate commands are reviewed for these different modes and the control system that is necessary to regulate the magnet current is described. Finally, the future is envisaged with the new trends in this direction.

Neutron yield in experiments with Z-pinches in frozen deuterium filaments

International Nuclear Information System (INIS)

Meierovich, B.E.; Sukhorukov, S.T.

1991-01-01

Experiments on the properties of the neutron yield and stability of dense Z-pinches in frozen deuterium filaments two years ago have still not received a proper explanation. A discharge in a dielectric deuterium filament differs qualitatively in its behavior from one in a metal conductor. The authors assert attempts to interpret the experiment have not taken this fact properly into account. The enhanced stability and substantial neutron yield do not follow from the classical picture of a Bennett equilibrium in the current channel. The most important experimental characteristic of a discharge in frozen deuterium is the dependence of the neutron yield on the current strength at a given stage. The spread in the experimental points is quite large so one naturally prefers t describe the experimental data by means of a physically simple model and not go to a full-scale simulation of all the processes. When the deuterium is fully ionized the electron drift velocity is smaller than the thermal velocity, enabling calculation of the neutron yield by means of a self-similar model of the Z-pinch compression which treats electron degeneracy. To find the neutron yield it suffices to consider only the first half-period of the self-similar oscillations including the state of maximum compression. The subsequent evolution of the current channel, which is associated with radial expansion, does not contribute significantly to the neutron yield

A short-pulse mode for the SPHINX LTD Z-pinch driver

Science.gov (United States)

D'Almeida, Thierry; Lassalle, Francis; Zucchini, Frederic; Loyen, Arnaud; Morell, Alain; Chuvatin, Alexander

2015-11-01

The SPHINX machine is a 6MA, 1 μs, LTD Z-pinch driver at CEA Gramat (France) and primarily used for studying radiation effects. Different power amplification concepts were examined in order to reduce the current rise time without modifying the generator discharge scheme, including the Dynamic Load Current Multiplier (DLCM) proposed by Chuvatin. A DLCM device, capable of shaping the current pulse without reducing the rise time, was developed at CEA. This device proved valuable for isentropic compression experiments in cylindrical geometry. Recently, we achieved a short pulse operation mode by inserting a vacuum closing switch between the DLCM and the load. The current rise time was reduced to ~300 ns. We explored the use of a reduced-height wire array for the Dynamic Flux Extruder in order to improve the wire array compression rate and increase the efficiency of the current transfer to the load. These developments are presented. Potential benefits of these developments for future Z pinch experiments are discussed.

Physics of reversed-field pinch profile sustainment

International Nuclear Information System (INIS)

Moses, R.W.

1984-01-01

A description of the Reversed-Field Pinch (RFP) is given, emphasizing the necessity of a magnetohydrodynamic (MHD) or kinetic process to sustain field reversal. Three sustainment mechanisms are reviewed: the MHD dynamo, the tangled discharge model, and nonlocal resistivity. A slab model of steady (ohmic) states is described. A relationship between ohmic state wave numbers and the minimum amplitude of nonsymmetric field components is given. If ohmic states are the sole source of the sustainment process, their wave lengths are probably much longer than the minor diameter of the plasma. Otherwise field asymmetries would exceed those observed in experiments. It is noted that internal field data are still limited, restricting the generality of our comments

Experimental study on dynamic stabilization of the MHD instability in pinch plasmas surrounded by a conducting shell

International Nuclear Information System (INIS)

Yamamoto, Shunji; Ishii, Shozo; Kawamoto, Shigeshi; Hayashi, Izumi

1981-01-01

Experimental study on the dynamic stabilization of MHD instability with a pinch plasma generator was done, and the results were compared with the theoretical works. The previous results of theoretical analysis showed that a conducting shell worked effectively for the dynamic stabilization of MHD instability. The present experiment was carried out with a linear plasma generator which consisted of a discharge tube, a coil and a conducting shell. The macroscopic behavior of plasma was observed with an image converter camera, and the phenomena due to the instability was measured by a magnetic probe. A sine-cosine coil was employed for the observation of the growth of instability. The following results were obtained. When the frequency of RF current for dynamic stabilization was larger than the growth rate of instability, the experimental results were in agreement with the theoretical ones. The effect of a conducting shell was clearly seen. For the helical instability of short wave length, the dynamic stabilization was easily obtained even without a conducting shell. The self-reversal phenomena due to the helical instability of short wave length was suppressed by the RF current along the axis of a discharge tube. (Kato, T.)

Pinch-off Scaling Law of Soap Bubbles

Science.gov (United States)

Davidson, John; Ryu, Sangjin

2014-11-01

Three common interfacial phenomena that occur daily are liquid drops in gas, gas bubbles in liquid and thin-film bubbles. One aspect that has been studied for these phenomena is the formation or pinch-off of the drop/bubble from the liquid/gas threads. In contrast to the formation of liquid drops in gas and gas bubbles in liquid, thin-film bubble pinch-off has not been well documented. Having thin-film interfaces may alter the pinch-off process due to the limiting factor of the film thickness. We observed the pinch-off of one common thin-film bubble, soap bubbles, in order to characterize its pinch-off behavior. We achieved this by constructing an experimental model replicating the process of a human producing soap bubbles. Using high-speed videography and image processing, we determined that the minimal neck radius scaled with the time left till pinch-off, and that the scaling law exponent was 2/3, similar to that of liquid drops in gas.

Linear theory of drift-tearing and interchange modes in a screw pinch

International Nuclear Information System (INIS)

Copenhaver, C.

1978-04-01

A drift dispersion relation, as applied to a resistive incompressible plasma in a screw pinch, is derived. This dispersion relation incorporates both drift-tearing and drift-interchange modes and is valid throughout the collisional regime by including kinetic theory factors. The dispersion relation reduces to the drift-tearing dispersion relation in the zero pressure gradient limit, and to the classical resistive dispersion relation in the zero drift limit. The electron temperature gradient instability is still present. Now, however, the introduction of the interchange-drift instability increases the growth rate further above the tearing-drift case. (orig.) [de

Radiative cooling of a cilindrical Z-pinch in the stage of plasma shett motion

International Nuclear Information System (INIS)

Gerusov, A.V.; Imshennik, V.S.

1982-01-01

Dinamics of a cylindrically symmetric Z-pinch in deiterium-neon mixture on the motion stage with volume radiation losses of energy of neon ions is considered. A two-temperature MHD model of Z-pinch is numerically calculated with various percentage of gases in mixture. It is found that radiation losses are essential in the dynamics of the discharqe. They decrease distribution of magnetic field and curreqt density. The temoerature of anode surface heated by absorbtion of radiation from the plasma sheath which forms in the discharge is obtained. The value of anode surface temperature prior to the arrival of the shock front is insufficient for operating of previously proposed mechanism of X-ray plasma focus regime. Another mechanism leading to X-ray regime being due to radiative cooiang as aiso suggested

Impurity behaviour in the EXTRAP-T1 pinch experiment studied by VUV spectroscopy

International Nuclear Information System (INIS)

Brzozowski, J.H.; Kaellne, E.; Zastrow, K.D. Royal Inst. of Tech., Stockholm

1989-11-01

Vacuum ultraviolet observations from a low-q, high-beta pinch plasma (Extrap-T1) are presented and related to other plasma parameters. Qualitative analysis of the line emission from low ionization stages of carbon and oxygen, which dominate this spectrum, gives information on the ionization stages reach a steady state during the equilibrium phase of the discharge, and that line radiation does not dominate the power balance. The energy balance of the plasma discharge is analysed from the vacuum ultraviolet line and continuum spectroscopy data. Furthermore it is found, that the time behaviour of the plasma resistance can be understood using the results from the spectroscopic observations. (authors)

High energy density Z-pinch plasmas using flow stabilization

Energy Technology Data Exchange (ETDEWEB)

Shumlak, U., E-mail: shumlak@uw.edu; Golingo, R. P., E-mail: shumlak@uw.edu; Nelson, B. A., E-mail: shumlak@uw.edu; Bowers, C. A., E-mail: shumlak@uw.edu; Doty, S. A., E-mail: shumlak@uw.edu; Forbes, E. G., E-mail: shumlak@uw.edu; Hughes, M. C., E-mail: shumlak@uw.edu; Kim, B., E-mail: shumlak@uw.edu; Knecht, S. D., E-mail: shumlak@uw.edu; Lambert, K. K., E-mail: shumlak@uw.edu; Lowrie, W., E-mail: shumlak@uw.edu; Ross, M. P., E-mail: shumlak@uw.edu; Weed, J. R., E-mail: shumlak@uw.edu [Aerospace and Energetics Research Program, University of Washington, Seattle, Washington, 98195-2250 (United States)

2014-12-15

The ZaP Flow Z-Pinch research project[1] at the University of Washington investigates the effect of sheared flows on MHD instabilities. Axially flowing Z-pinch plasmas are produced that are 100 cm long with a 1 cm radius. The plasma remains quiescent for many radial Alfvén times and axial flow times. The quiescent periods are characterized by low magnetic mode activity measured at several locations along the plasma column and by stationary visible plasma emission. Plasma evolution is modeled with high-resolution simulation codes – Mach2, WARPX, NIMROD, and HiFi. Plasma flow profiles are experimentally measured with a multi-chord ion Doppler spectrometer. A sheared flow profile is observed to be coincident with the quiescent period, and is consistent with classical plasma viscosity. Equilibrium is determined by diagnostic measurements: interferometry for density; spectroscopy for ion temperature, plasma flow, and density[2]; Thomson scattering for electron temperature; Zeeman splitting for internal magnetic field measurements[3]; and fast framing photography for global structure. Wall stabilization has been investigated computationally and experimentally by removing 70% of the surrounding conducting wall to demonstrate no change in stability behavior.[4] Experimental evidence suggests that the plasma lifetime is only limited by plasma supply and current waveform. The flow Z-pinch concept provides an approach to achieve high energy density plasmas,[5] which are large, easy to diagnose, and persist for extended durations. A new experiment, ZaP-HD, has been built to investigate this approach by separating the flow Z-pinch formation from the radial compression using a triaxial-electrode configuration. This innovation allows more detailed investigations of the sheared flow stabilizing effect, and it allows compression to much higher densities than previously achieved on ZaP by reducing the linear density and increasing the pinch current. Experimental results and

The physics of fast Z pinches

International Nuclear Information System (INIS)

Ryutov, D.D.; Derzon, M.S.; Matzen, M.K.

1998-07-01

The spectacular progress made during the last few years in reaching high energy densities in fast implosions of annular current sheaths (fast Z pinches) opens new possibilities for a broad spectrum of experiments, from x-ray generation to controlled thermonuclear fusion and astrophysics. Presently Z pinches are the most intense laboratory X ray sources (1.8 MJ in 5 ns from a volume 2 mm in diameter and 2 cm tall). Powers in excess of 200 TW have been obtained. This warrants summarizes the present knowledge of physics that governs the behavior of radiating current-carrying plasma in fast Z-pinches. This survey covers essentially all aspects of the physics of fast Z pinches: initiation, instabilities of the early stage, magnetic Rayleigh-Taylor instability in the implosion phase, formation of a transient quasi-equilibrium near the stagnation point, and rebound. Considerable attention is paid to the analysis of hydrodynamic instabilities governing the implosion symmetry. Possible ways of mitigating these instabilities are discussed. Non-magnetohydrodynamic effects (anomalous resistivity, generation of particle beams, etc.) are summarized. Various applications of fast Z pinches are briefly described. Scaling laws governing development of more powerful Z pinches are presented. The survey contains 52 figures and nearly 300 references

The Physics of Fast Z Pinches

Energy Technology Data Exchange (ETDEWEB)

RYUTOV,D.D.; DERZON,MARK S.; MATZEN,M. KEITH

1999-10-25

The spectacular progress made during the last few years in reaching high energy densities in fast implosions of annular current sheaths (fast Z pinches) opens new possibilities for a broad spectrum of experiments, from x-ray generation to controlled thermonuclear fusion and astrophysics. Presently Z pinches are the most intense laboratory X ray sources (1.8 MJ in 5 ns from a volume 2 mm in diameter and 2 cm tall). Powers in excess of 200 TW have been obtained. This warrants summarizing the present knowledge of physics that governs the behavior of radiating current-carrying plasma in fast Z pinches. This survey covers essentially all aspects of the physics of fast Z pinches: initiation, instabilities of the early stage, magnetic Rayleigh-Taylor instability in the implosion phase, formation of a transient quasi-equilibrium near the stagnation point, and rebound. Considerable attention is paid to the analysis of hydrodynamic instabilities governing the implosion symmetry. Possible ways of mitigating these instabilities are discussed. Non-magnetohydrodynamic effects (anomalous resistivity, generation of particle beams, etc.) are summarized. Various applications of fast Z pinches are briefly described. Scaling laws governing development of more powerful Z pinches are presented. The survey contains 36 figures and more than 300 references.

Progress on z-pinch inertial fusion energy

International Nuclear Information System (INIS)

Olson, C.; Rochau, G.; Matzen, M.K.

2005-01-01

The goal of z-pinch inertial fusion energy (IFE) is to extend the single-shot z-pinch inertial confinement fusion (ICF) results on Z to a repetitive-shot z-pinch power plant concept for the economical production of electricity. Z produces up to 1.8 MJ of x-rays at powers as high as 230 TW. Recent target experiments on Z have demonstrated capsule implosion convergence ratios of 14-21 with a double-pinch driven target, and DD neutron yields up to 8x10exp10 with a dynamic hohlraum target. For z-pinch IFE, a power plant concept is discussed that uses high-yield IFE targets (3 GJ) with a low rep-rate per chamber (0.1 Hz). The concept includes a repetitive driver at 0.1 Hz, a Recyclable Transmission Line (RTL) to connect the driver to the target, high-yield targets, and a thick-liquid wall chamber. Recent funding by a U.S. Congressional initiative for $4M for FY04 is supporting research on RTLs, repetitive pulsed power drivers, shock mitigation, full RTL cycle planned experiments, high-yield IFE targets, and z-pinch power plant technologies. Recent results of research in all of these areas are discussed, and a Road Map for Z-Pinch IFE is presented. (author)

History of the Z-pinch

International Nuclear Information System (INIS)

Lovberg, R.H.

1988-01-01

The plasma Z-Pinch occupies a unique position in the history of controlled fusion research as the first confinement and heating scheme to be tried experimentally. In contrast to the sophistication of programs being conducted today, in which extensive theoretical and experimental forces are in close collaboration, early pinch experiments were designed on quite elementary theoretical grounds. Indeed, these systems and the results from them provided the focus for much of the rapid development of theoretical plasma physics and magnetohydrodynamics during the 1950's. In comparison to present programs, these early experiments had the considerable advantage of small size and minimal managerial encumbrance. After nearly three decades of abandonment because of difficulties with MHD instabilities, the Z-pinch is arising once again in a new incarnation characterized by microscopic size and time scales, and very high density. Uniquely in the history of the pinch, the new experimental surprises seem encouraging, rather than discouraging, to the goal of thermonuclear fusion

Daily Suspended Sediment Discharge Prediction Using Multiple Linear Regression and Artificial Neural Network

Science.gov (United States)

Uca; Toriman, Ekhwan; Jaafar, Othman; Maru, Rosmini; Arfan, Amal; Saleh Ahmar, Ansari

2018-01-01

Prediction of suspended sediment discharge in a catchments area is very important because it can be used to evaluation the erosion hazard, management of its water resources, water quality, hydrology project management (dams, reservoirs, and irrigation) and to determine the extent of the damage that occurred in the catchments. Multiple Linear Regression analysis and artificial neural network can be used to predict the amount of daily suspended sediment discharge. Regression analysis using the least square method, whereas artificial neural networks using Radial Basis Function (RBF) and feedforward multilayer perceptron with three learning algorithms namely Levenberg-Marquardt (LM), Scaled Conjugate Descent (SCD) and Broyden-Fletcher-Goldfarb-Shanno Quasi-Newton (BFGS). The number neuron of hidden layer is three to sixteen, while in output layer only one neuron because only one output target. The mean absolute error (MAE), root mean square error (RMSE), coefficient of determination (R2 ) and coefficient of efficiency (CE) of the multiple linear regression (MLRg) value Model 2 (6 input variable independent) has the lowest the value of MAE and RMSE (0.0000002 and 13.6039) and highest R2 and CE (0.9971 and 0.9971). When compared between LM, SCG and RBF, the BFGS model structure 3-7-1 is the better and more accurate to prediction suspended sediment discharge in Jenderam catchment. The performance value in testing process, MAE and RMSE (13.5769 and 17.9011) is smallest, meanwhile R2 and CE (0.9999 and 0.9998) is the highest if it compared with the another BFGS Quasi-Newton model (6-3-1, 9-10-1 and 12-12-1). Based on the performance statistics value, MLRg, LM, SCG, BFGS and RBF suitable and accurately for prediction by modeling the non-linear complex behavior of suspended sediment responses to rainfall, water depth and discharge. The comparison between artificial neural network (ANN) and MLRg, the MLRg Model 2 accurately for to prediction suspended sediment discharge (kg

Z-Pinch Fusion for Energy Applications

Energy Technology Data Exchange (ETDEWEB)

SPIELMAN,RICK B.

2000-01-01

Z pinches, the oldest fusion concept, have recently been revisited in light of significant advances in the fields of plasma physics and pulsed power engineering. The possibility exists for z-pinch fusion to play a role in commercial energy applications. We report on work to develop z-pinch fusion concepts, the result of an extensive literature search, and the output for a congressionally-mandated workshop on fusion energy held in Snowmass, Co July 11-23,1999.

Z-Pinch Fusion for Energy Applications

International Nuclear Information System (INIS)

SPIELMAN, RICK B.

2000-01-01

Z pinches, the oldest fusion concept, have recently been revisited in light of significant advances in the fields of plasma physics and pulsed power engineering. The possibility exists for z-pinch fusion to play a role in commercial energy applications. We report on work to develop z-pinch fusion concepts, the result of an extensive literature search, and the output for a congressionally-mandated workshop on fusion energy held in Snowmass, Co July 11-23,1999

Sounding experiments of high pressure gas discharge

International Nuclear Information System (INIS)

Biele, Joachim K.

1998-01-01

A high pressure discharge experiment (200 MPa, 5·10 21 molecules/cm 3 , 3000 K) has been set up to study electrically induced shock waves. The apparatus consists of the combustion chamber (4.2 cm 3 ) to produce high pressure gas by burning solid propellant grains to fill the electrical pump chamber (2.5 cm 3 ) containing an insulated coaxial electrode. Electrical pump energy up to 7.8 kJ at 10 kV, which is roughly three times of the gas energy in the pump chamber, was delivered by a capacitor bank. From the current-voltage relationship the discharge develops at rapidly decreasing voltage. Pressure at the combustion chamber indicating significant underpressure as well as overpressure peaks is followed by an increase of static pressure level. These data are not yet completely understood. However, Lorentz forces are believed to generate pinching with subsequent pinch heating, resulting in fast pressure variations to be propagated as rarefaction and shock waves, respectively. Utilizing pure axisymmetric electrode initiation rather than often used exploding wire technology in the pump chamber, repeatable experiments were achieved

Compact toroid formation using barrier fields and controlled reconnection in the TRX-1 field reversed theta pinch

International Nuclear Information System (INIS)

Hoffman, A.L.; Armstrong, W.T.

1982-01-01

TRX-1 is a new 20 cm diameter, 1-m long field reversed theta pinch with a magnetic field swing of 10 kG in 3 μsec. It employs z discharge preionization and octopole barrier fields to maximize flux trapping on first half cycle operation. Cusp coils are used at the theta pinch ends to delay reconnection and fast mirror coils are used to trigger reconnection at a time designed to maximize axial heating efficiency and toroid lifetime. These controls are designed to study toroid formation methods which are claimed to be especially efficient by Russian experimenters. Studies have been conducted on flux trapping efficiency, triggered reconnection, and equilibrium and lifetime

Neutron Spectrum Measured by Activation Diagnostics in Deuterium Gas-Puff Experiments on the 3 MA GIT-12 Z-Pinch

Czech Academy of Sciences Publication Activity Database

Cikhardt, J.; Klír, D.; Řezáč, K.; Shishlov, A. V.; Cherdizov, R. K.; Cikhardtová, B.; Dudkin, G. N.; Fursov, F. I.; Kokshenev, V. A.; Kravařík, J.; Kubeš, P.; Kurmaev, N. E.; Labetsky, A. Yu.; Padalko, V. N.; Ratakhin, N. A.; Šíla, O.; Turek, Karel; Varlachev, V. A.

2017-01-01

Roč. 45, č. 12 (2017), s. 3209-3217 ISSN 0093-3813 Institutional support: RVO:61389005 Keywords : neutron detectors * neutron spectroscopy * plasma pinch Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 1.052, year: 2016

High-density fusion and the Z-pinch

International Nuclear Information System (INIS)

Hartman, C.W.; Eddleman, J.L.; Munger, R.H.

1975-01-01

The formation of a Z-pinch in dense gas is investigated using numerical modeling in one and two dimensions. Hot, dense Z-pinches are calculated with n approximately 2 x 10 21 cm 3 and T = 10 keV. Relaxation by sausage instability of an unstable pinch profile to a marginally stable one is calculated along with end losses in 2 dimensions to show that, if plasma is confined for N = 50 to 200 sound transits across the radius a, pinches with length L = Na are of interest for fusion power. A conceptual, ''no-wall'' fusion reactor is discussed. (author)

Fusion reaction yield in focused discharges with variable energy and plasma fine structure

International Nuclear Information System (INIS)

Bortolotti, A.; Brzosko, J.S.; Chiara, P. De; Kilic, H.; Mezzetti, F.; Nardi, V.; Powell, C.; Wang, J.

1992-01-01

The same linear correlation between the distribution parameters (ΔT and Max ΔV) of the radial current density J between electrodes and the fusion reaction yield per pulse, Y, in the plasma focus (PF) pinch was quantitatively determined from different PF machines. Contact prints of current-sheath fragments (CSF) ejected from the pinch are obtained from 2.5-MeV-D + ions. CSF's show the same submillimetric fine structure of the pinch. (author) 3 refs., 2 tabs

Pinch Strengths in Healthy Iranian Children and Young Adult Population

Directory of Open Access Journals (Sweden)

Iman Dianat

2015-03-01

Full Text Available Background: Data on the physical strength capabilities are essential for design-ing safe and usable products and are useful in a wide range of clinical settings especially during treatment of disease affecting the function of the hand. The purpose of this study was to determine peak lateral pinch strength, key pinch strength, tip-to-tip pinch strength and three-jaw pinch strength exertions in a healthy Iranian children and young adult population.Methods: The study was conducted among 511 participants (242 males and 269 females aged 7-30 years. Measurements were carried out with both dominant and non-dominant hands in standard sitting posture using a B&L pinch gauge. Two repetitions of each strength measurement were recorded for each condition and the average value of the two trials was used in the subsequent analysis.Results: The results showed significant differences in the pinch strength data in terms of the age, gender and hand dominance. The lateral pinch strength, key pinch strength, tip-to-tip pinch strength and three-jaw pinch strength exertions by females were 68.4%, 68.8%, 78.8% and 81.8% of those exerted by males, respectively. Strength exertions with the non-dominant hand were 6.4%, 5.2%, 6.6% and 5.1% lower than strength exertions of the dominant hand for the lat-eral pinch strength, key pinch strength, tip-to-tip pinch strength and three-jaw pinch strength exertions, respectively.Conclusion: These findings can be used to fill the gaps in strength data for Iranian population.

Hybrid simulations of current-carrying instabilities in Z-pinch plasmas with sheared axial flow

International Nuclear Information System (INIS)

Sotnikov, Vladimir I.; Makhin, Volodymyr; Bauer, Bruno S.; Hellinger, Petr; Travnicek, Pavel; Fiala, Vladimir; Leboeuf, Jean-Noel

2002-01-01

The development of instabilities in z-pinch plasmas has been studied with three-dimensional (3D) hybrid simulations. Plasma equilibria without and with sheared axial flow have been considered. Results from the linear phase of the hybrid simulations compare well with linear Hall magnetohydrodynamics (MHD) calculations for sausage modes. The hybrid simulations show that sheared axial flow has a stabilizing effect on the development of both sausage and kink modes

The ZaP Flow Z-Pinch Project

International Nuclear Information System (INIS)

Shumlak, U.; Nelson, B. A.

2005-01-01

The results from the ZaP experiment are consistent with the theoretical predictions of sheared flow stabilization. Z pinches with a sheared flow are generated in the ZaP experiment using a coaxial accelerator coupled to an assembly region. The current sheet in the accelerator initially acts as a snowplow. As the Z pinch forms, plasma formation in the accelerator transits to a deflagration process. The plasma exits the accelerator and maintains the flow in the Z pinch. During the quiescent period in the magnetic mode activity at z=0 cm, a stable Z pinch is seen on the axis of the assembly region. The evolution of the axial velocity profile shows a large velocity shear is measured at the edge of the Z pinch during the quiescent period. The velocity shear is above the theoretical threshold. As the velocity shear decreases towards 0.1kV A , the predicted stability threshold, the quiescent period ends. The present understanding of the ZaP experiment shows that it may be possible for the Z pinch to operate in a steady state if the deflagration process can be maintained by constantly supplying neutral gas or plasma to the accelerator

Amount of impurity and its behavior in the STP-2 screw pinch tokamak

International Nuclear Information System (INIS)

Yamaguchi, S.

1981-05-01

Temporal and spatial evolution of oxygen spectral line intensities have been measured in the STP-2 screw pinch tokamak. The electron density and temperature as measured by Thomson scattering are of the order of 10 14 cm -3 and 10 eV, respectively. On the basis of these measurements, quasi-steady-state rate equations have been solved to give the OII and OIII ion densities. It is found that the density of oxygen impurity is about several percent of the electron density, and the impurity moves with the bulk plasma. It is confirmed that the impurity originates from the wall of the discharge tube during the initial phase of the discharge. (author)

Investigation on the pinch point position in heat exchangers

Science.gov (United States)

Pan, Lisheng; Shi, Weixiu

2016-06-01

The pinch point is important for analyzing heat transfer in thermodynamic cycles. With the aim to reveal the importance of determining the accurate pinch point, the research on the pinch point position is carried out by theoretical method. The results show that the pinch point position depends on the parameters of the heat transfer fluids and the major fluid properties. In most cases, the pinch point locates at the bubble point for the evaporator and the dew point for the condenser. However, the pinch point shifts to the supercooled liquid state in the near critical conditions for the evaporator. Similarly, it shifts to the superheated vapor state with the condensing temperature approaching the critical temperature for the condenser. It even can shift to the working fluid entrance of the evaporator or the supercritical heater when the heat source fluid temperature is very high compared with the absorbing heat temperature. A wrong position for the pinch point may generate serious mistake. In brief, the pinch point should be founded by the iterative method in all conditions rather than taking for granted.

Self-pinched lithium beam transport experiments on SABRE

International Nuclear Information System (INIS)

Hanson, D.L.; Olson, C.L.; Poukey, J.W.; Shokir, I.; Cuneo, M.E.; Menge, P.R.; Johnston, R.R.; Welch, D.R.

1996-01-01

Self-pinched transport of ion beams has many advantages for ion-driven ICF applications involving high yield and energy production. The authors are currently preparing for a self-pinched lithium beam transport experiment on the SABRE accelerator. There are three transport elements that must eventually be demonstrated: (1) efficient lithium beam generation and ballistic transport to a focus at the self-pinched transport channel entrance; (2) self-pinched transport in the channel, requiring optimized injection conditions and gas breakdown; and (3) self-pinched transport of the equilibrated beam from the channel into free space, with associated aiming and stability considerations. In the present experiment, a hollow annular lithium beam from an applied-B extraction ion diode will be focused to small radius (r ≤ 2 cm) in a 60 cm long ballistic focus section containing argon gas at a pressure of a few Torr. The self-pinched transport channel will contain a low pressure background gas of 10--40 mTorr argon to allow sufficient net current to confine the beam for long distance transport. IPROP simulations are in progress to optimize the design of the ballistic and self-pinched transport sections. Progress on preparation of this lithium self-pinched transport experiment, including a discussion of transport system design, important gas breakdown issues, and diagnostics, will be presented

2D radiation-magnetohydrodynamic simulations of SATURN imploding Z-pinches

International Nuclear Information System (INIS)

Hammer, J.H.; Eddleman, J.L.; Springer, P.T.

1995-01-01

Z-pinch implosions driven by the SATURN device at Sandia National Laboratory are modeled with a 2D radiation magnetohydrodynamic (MHD) code, showing strong growth of magneto-Rayleigh Taylor (MRT) instability. Modeling of the linear and nonlinear development of MRT modes predicts growth of bubble-spike structures that increase the time span of stagnation and the resulting x-ray pulse width. Radiation is important in the pinch dynamics keeping the sheath relatively cool during the run-in and releasing most of the stagnation energy. The calculations give x-ray pulse widths and magnitudes in reasonable agreement with experiments, but predict a radiating region that is too dense and radially localized at stagnation. We also consider peaked initial density profiles with constant imploding sheath velocity that should reduce MRT instability and improve performance. 2D krypton simulations show an output x-ray power > 80 TW for the peaked profile

Physical features of the wire-array Z-pinch plasmas imploding process

International Nuclear Information System (INIS)

Gao Chunming; Feng Kaiming

2001-01-01

In the process of research on controlled fusion reactors, scientists found that the Z-pinch plasma can produce very strong X-rays, comparing with other X-ray sources. In researching the process of imploding, the snowplow model and Haines model are introduced and proved. About amassing X-rays, several ways of discharging X-rays are carefully analyzed and the relative theories are proved. In doing simulations, the one dimension model is used in writing codes, the match relationships are calculated and the process of imploding is also simulated. Some useful and reasonable results are obtained

Physics of the dense Z-pinch in theory and in experiment with application to fusion reactor

Energy Technology Data Exchange (ETDEWEB)

Haines, M.G. (Imperial Coll. of Science and Technology, London (UK). Blackett Lab.)

1982-01-01

A new generation of Z-pinches employing high voltage, high current pulsed lines as power sources produce dense hot plasmas with enhanced stability properties. Three methods of Z-pinch formation are currently in use: (1) cylindrical collapse and compression of a pre-ionised gas; (2) laser initiation and Joule heating of a gas embedded pinch, and (3) hollow gas puff and subsequent collapse to the axis. The first two experimental conditions are relevant for fusion. A calculation of energy balance for satisfying Lawson conditions with axial and radial energy losses and radiation loss shows that a current of approximately 10/sup 6/ A and a line density of 6 x 10/sup 18/ m/sup -1/ are required. This leads to two coincidences of physical quantities that are very favourable for controlled fusion. The first is that at this line density and under pressure balance the ratio of the ion Larmor radius to pinch is of order 1 so that a marked stabilisation of the configuration is expected. The second coincidence is that the current is only just below the Pease-Braginskii limit; this will permit the possibility or radiative collapse to attain the high density (approximately 4 x 10/sup 27/ m/sup -3/) and small radius (approximately 20 ..mu..m) required for a compact (0.1 m long) discharge.

Scaling of sustained ZT-40 M reversed field pinches

International Nuclear Information System (INIS)

Graham, J.; Haberstich, A.; Baker, D.A.; Buchenauer, C.J.; Caramana, E.J.; DiMarco, J.N.; Erickson, R.M.; Ingraham, J.C.; Jacobson, A.R.; Little, E.M.; Massey, R.S.; Phillips, J.A.; Schoenberg, K.F.; Schofield, A.E.; Thomas, K.S.; Watt, R.G.; Weber, P.G.

1993-12-01

Experiments aimed at evaluating the scaling properties of the ZT-40M Reversed-Field Pinch (RFP) facility were conducted in 1983 at Los Alamos. Sustained discharges were produced at nominal toroidal currents ranging from 60 to 240 kA. The standard fill pressure was kept close to the lower limit of the usable pressure range, and the scaling data were acquired at a fixed time in the discharges while the plasma was in a quasi-steady state. Scalings of the diameter-averaged electron density, electron temperature on axis, product of these two parameters, and of various definitions of the electrical resistivity are presented. Trends of the toroidal voltage, energy containment time, and poloidal beta are shown. The impurity contents, particle containment time, and total radiation losses are described, and results obtained with and without poloidal limiters are compared. In addition, the performance of the facility at higher than standard density and at a constant ratio of the toroidal current over the electron line density is examined

Measurements for the radiation spectra of fast Z-pinches produced at compression of multi-wire arrays on the 'Angara-5-1' facility

International Nuclear Information System (INIS)

Bolkhovitinov, E.A.; Rupasov, A.A.; Shikanov, A.S.; Fedulov, M.V.; Grabovsky, E.V.; Gritsuk, A.N.; Oleinik, G.M.; Volkov, G.S.

2010-01-01

Complete text of publication follows. The measurements results on the radiation spectra of fast z-pinches produced at compression of cylindrical multi-wire tungsten and aluminum arrays in the experiments on a high-current 'Angara-5-1' facility are presented. Cylindrical multi-wire arrays has linear mass 200-400 μg/cm and the initial diameter 12-20 mm. The pinch current was about 3 MA with pulse duration of 140 ns and peak power 3 TW. The radiation spectra are measured within the range of 50-900 eV quanta by a spectrometer with transmission diffraction grating, where the radiation is recorded on the UF-4 X-ray film. An electromagnetic curtain shutter was used to protect the transmission grating from fast microparticles produced by the erosion of high-voltage electrodes. The radiation spectrum of 1-3 keV quanta was recorded by a convex crystal wide-range spectrometer. Total yield of the radiation was measured by a thermocouple calorimeter. The main part of the tungsten plasma radiative energy proves to correspond to the quasi-continuous spectrum within the range of 80-300 eV quanta. Measurements of the tungsten plasma radiation spectrum with spatial resolution by a pinch radius have shown that the effective transversal size (diameter) of the pinch as not higher than 1 mm. In the case of aluminum plasma an intensive linear radiation of the [H]- and [He]-like ions have been recorded along with a continuous and linear radiation of the [Li]- and [Be]-like ions with the range of 100-300 eV quanta. Spectral measurements of the aluminum plasma radiation with spatial resolution by the pinch radius have shown that the effective transversal size (diameter) of the pinch is around the value of 1.5 mm. Within the framework of the stationary collisional-radiative model, in respect of the [H]- and [He]-like ion spectral lines relative intensities, the parameters of the aluminum plasma pinch, namely, the electron temperature T e ∼ 550 eV and electron density n e ∼ 3 x 10 20 cm

Characteristics of x-ray radiation from a gas-puff z-pinch plasma

International Nuclear Information System (INIS)

Akiyama, N.; Takasugi, K.

2002-01-01

Characteristics of x-ray radiation from Ar gas-puff z-pinch plasma have been investigated by changing delay time of discharge from gas puffing. Intense cloud structure of x-ray image was observed at small delay time region, but the total x-ray signal was not so intense. The x-ray signal increased with increasing the delay time, and hot spots of x-ray image also became intense. Electron temperature was evaluated from x-ray spectroscopic data, and no significant difference in temperature was observed. (author)

The static pinch

Energy Technology Data Exchange (ETDEWEB)

Longmire, Conrad L [University of California, Los Alamos Scientific Laboratory, Los Alamos, NM (United States)

1958-07-01

In a pinch, the outward diffusion of plasma due to collisions can be balanced by the inward drift resulting from ExB, where E is the applied electric field and B the magnetic field. From the equation expressing the balance of these two effects, together with the pressure balance equation, one obtains the perpendicular conductivity, which is about one-half of the classical parallel conductivity. This result has been applied to the problem of a static pinch under the assumptions: 1) there is an applied longitudinal (B{sub z}) magnetic field; 2) the plasma is isothermal; 3) the solution depends only on the radial coordinate.

Ion clusters, REB, and current sheath characteristics in focused discharges

International Nuclear Information System (INIS)

Bortolotti, A.; Brzosko, J.; DeChiara, P.; Kilic, H.; Mezzetti, F.; Nardi, V.; Powell, C.; Zeng, D.

1990-01-01

Small fluctuations in the current sheath characteristics (peak current density, FWHM of leading sheath, control parameters of sheath internal structure) are linked to wide fluctuations of ion and ion cluster emission from the pinch. Magnetic probe data are used for correlating variations of current sheath parameters with particle emission intensity, Z/M composition, particle energy spectrum. The emission of ion and ion clusters at 90 degrees from the axis of a plasma focus discharge is monitored simultaneously with the 0 degrees emission. The particle energy spectrum is analyzed with a Thomson (parabola) spectrometer (time resolution ∼ 1 nanosec). The cross-sectional structure of the REB at 180 degrees along the discharge axis is monitored via the deposition of collective-field accelerated ions on a target in the REB direction. Etched tracks of ion and ion clusters are in all cases recorded on CR-39 plates. Sharp peaks of the D + -ion spectrum at 90 degrees are found for E > 200 keV/unit charge in all focused discharges. These peaks are due to ion crossing of the azimuthal magnetic field of the pinch region, in a predominant ion cluster structure

Progress in symmetric ICF capsule implosions and wire-array z-pinch source physics for double z-pinch driven hohlraums

International Nuclear Information System (INIS)

Bliss, David Emery; Vesey, Roger Alan; Rambo, Patrick K.; Lebedev, Sergey V.; Hanson, David L.; Nash, Thomas J.; Yu, Edmund P.; Matzen, Maurice Keith; Afeyan, Bedros B.; Smith, Ian Craig; Stygar, William A.; Porter, John Larry Jr.; Cuneo, Michael Edward; Bennett, Guy R.; Campbell, Robert B.; Sinars, Daniel Brian; Chittenden, Jeremy Paul; Waisman, Eduardo Mario; Mehlhorn, Thomas Alan

2005-01-01

Over the last several years, rapid progress has been made evaluating the double-z-pinch indirect-drive, inertial confinement fusion (ICF) high-yield target concept (Hammer et al 1999 Phys. Plasmas 6 2129). We have demonstrated efficient coupling of radiation from two wire-array-driven primary hohlraums to a secondary hohlraum that is large enough to drive a high yield ICF capsule. The secondary hohlraum is irradiated from two sides by z-pinches to produce low odd-mode radiation asymmetry. This double-pinch source is driven from a single electrical power feed (Cuneo et al 2002 Phys. Rev. Lett. 88 215004) on the 20 MA Z accelerator. The double z-pinch has imploded ICF capsules with even-mode radiation symmetry of 3.1 ± 1.4% and to high capsule radial convergence ratios of 14-21 (Bennett et al 2002 Phys. Rev. Lett. 89 245002; Bennett et al 2003 Phys. Plasmas 10 3717; Vesey et al 2003 Phys. Plasmas 10 1854). Advances in wire-array physics at 20 MA are improving our understanding of z-pinch power scaling with increasing drive current. Techniques for shaping the z-pinch radiation pulse necessary for low adiabat capsule compression have also been demonstrated.

Study of flow and loss processes at the ends of a linear theta pinch. Progress report, June 1, 1977--May 31, 1978

International Nuclear Information System (INIS)

York, T.M.; Klevans, E.H.

1978-02-01

Experimental and analytical studies of end loss from a theta pinch have been carried out. Detailed diagnostic studies of a 25 cm long theta pinch operating with reversed trapped fields have been completed; spectroscopic studies, magnetic probe, pressure probe, double diamagnetic loop, luminosity studies and Thomson scattering studies of the plasma have been carried out over the 8 μsec duration of the transient loss. Two new diagnostic techniques have been developed based on the available Thomson scattering laser source. A study of plasma loss from a 10.5 long theta pinch with an axial Twyman-Green interferometer has been completed and reported. The basic studies needed for subsequent experimental work on heat conduction loss being diagnosed by Thomson scattering data in the end region, with and without mirror coil, has been completed as a part of the mirror field studies

Sausage mode of a high density Z-pinch

International Nuclear Information System (INIS)

Pereira, N.; Rostoker, N.

1983-01-01

In Z-pinch experiments at Maxwell Laboratories, Inc., growth rates have been measured by observing optical emission along the pinch axis. Growth rates estimated by means of the usual model of a pinch involving an incompressible fluid and a surface current are too large by a factor of 2-4. X-ray pinhole photographs generally have the appearance of a series of beads that would be expected from instability of the sausage mode. In some cases, particularly the implosion of large diameter wire arrays with BLACKJACK 5, the beads disappear and only the kink instability is apparent. Generalizing the pinch model to include compressibility does not significantly alter the predictions. A further generalization to include distributed current has therefore been considered. It seems likely that the current can penetrate significantly during the lifetime of the pinch. We consider a model of the pinch that is initially an infinite cylinder. For the sausage mode, stability is determined by a simple second order differential equation together with the boundary condition that follows from the wave number and the frequency of the instability

Nonlinear stage of a Z-pinch instability

International Nuclear Information System (INIS)

Garanin, S.F.; Chernyshev, Y.D.

1987-01-01

The nonlinear evolution of the sausage instability is analyzed for a Z-pinch with a fully developed skin effect in the current. Two-dimensional numerical calculations carried out on the sausage instability show that its occurrence leads to a stage describable by a self-similar solution when the length of the neck is fixed and the plasma compression is isentropic. At a perturbation wavelength small in comparison with the pinch radius, this stage is preceded by a stage which reduces to a nonlinear Rayleigh--Taylor instability. The dynamics of the motion of magnetic field ''bubbles'' and of plasma ''jets'' is analyzed in this case. The plasma jets emerging from the pinch do not block the pinch from the current source

Development of pulsed high current drivers for fast Z-pinch

International Nuclear Information System (INIS)

Sun Fengju; Qiu Aici; Zeng Zhengzhong; Zeng Jiangtao; Kuai Bin; Yang Hailiang

2006-01-01

It is required that the peak current of high power pulsed drive for fast Z-pinch reaches 60 MA to realize inertial confine fusion (ICF) and high yield (HY). With the conventional technological methods similar to the Z or Saturn apparatus, increasing driver current further is impractical and difficult according to the cost, structure complexity and reliability of the driver, so it is necessary to develop novel fast pulsed high current driver. The present art-of-state and trends of fast Z-pinch driver are summarized, and the typical conceptual designs and technological methods on ICF/HY PRS (plasma radiation source) and destroying-level super X-ray simulators in USA and Russia are outlined, such as HCEI's UGXX1 driver and new Saturn driver based on fast linear transformer driver (FLTD) and novel driver based on fast Marx generator (FMG) with current of 15 MA. The crucial technological problems and requirements to investigate in the future are presented. (authors)

Plasma focus - dense Z pinch and their applications

International Nuclear Information System (INIS)

Ishii, Shozo

1986-02-01

''Workshop on the possibility of Z-pinch as a intense pulse light source'' in 1983 and ''Research meeting on plasma focus and Z-pinch'' in 1984 were held at Institute of Plasma Physics, Nagoya University under a collaborating research program. Research activities reported at the meetings on plasma focus, dense Z-pinch, and related phenomena are summerized. (author)

TeV e+e- linear colliders

International Nuclear Information System (INIS)

Le Duff, J.

1987-12-01

The basic philosophy and performance and technical constraints of linear e + e - colliders at TeV energies are summarized. Collider luminosity, pinch effects due to beam interaction, beam-beam bremsstrahlung, and typical parameters for an e + e - linear collider are discussed. Accelerating structures, HF power sources, electron guns, positron production, and storage rings are considered [fr

1/4-pinched contact sphere theorem

DEFF Research Database (Denmark)

Ge, Jian; Huang, Yang

2016-01-01

Given a closed contact 3-manifold with a compatible Riemannian metric, we show that if the sectional curvature is 1/4-pinched, then the contact structure is universally tight. This result improves the Contact Sphere Theorem in [EKM12], where a 4/9-pinching constant was imposed. Some tightness...

Evaluation of accuracy of linear regression models in predicting urban stormwater discharge characteristics.

Science.gov (United States)

Madarang, Krish J; Kang, Joo-Hyon

2014-06-01

Stormwater runoff has been identified as a source of pollution for the environment, especially for receiving waters. In order to quantify and manage the impacts of stormwater runoff on the environment, predictive models and mathematical models have been developed. Predictive tools such as regression models have been widely used to predict stormwater discharge characteristics. Storm event characteristics, such as antecedent dry days (ADD), have been related to response variables, such as pollutant loads and concentrations. However it has been a controversial issue among many studies to consider ADD as an important variable in predicting stormwater discharge characteristics. In this study, we examined the accuracy of general linear regression models in predicting discharge characteristics of roadway runoff. A total of 17 storm events were monitored in two highway segments, located in Gwangju, Korea. Data from the monitoring were used to calibrate United States Environmental Protection Agency's Storm Water Management Model (SWMM). The calibrated SWMM was simulated for 55 storm events, and the results of total suspended solid (TSS) discharge loads and event mean concentrations (EMC) were extracted. From these data, linear regression models were developed. R(2) and p-values of the regression of ADD for both TSS loads and EMCs were investigated. Results showed that pollutant loads were better predicted than pollutant EMC in the multiple regression models. Regression may not provide the true effect of site-specific characteristics, due to uncertainty in the data. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Architecture of petawatt-class z-pinch accelerators

International Nuclear Information System (INIS)

Stygar, William A.; Mazarakis, Michael Gerrassimos; Cuneo, Michael Edward; Leeper, Ramon Joe; Ives, H.C.; Headley, D.I.; Wagoner, Tim C.; Porter, John Larry Jr.

2006-01-01

We have developed an accelerator architecture that can serve as the basis of the design of petawatt-class z-pinch drivers. The architecture has been applied to the design of two z-pinch accelerators, each of which can be contained within a 104-m-diameter cylindrical tank. One accelerator is driven by slow (∼1 (micro)s) Marx generators, which are a mature technology but which necessitate significant pulse compression to achieve the short pulses ( 4 capacitors, store 98 MJ, and erect to 5 MV; (ii) 600 water-dielectric triplate intermediate-store transmission lines, which also serve as pulse-forming lines; (iii) 600 5-MV laser-triggered gas switches; (iv) three monolithic radial-transmission-line impedance transformers, with triplate geometries and exponential impedance profiles; (v) a 6-level 5.5-m-diameter 15-MV vacuum insulator stack; (vi) six magnetically insulated vacuum transmission lines (MITLs); and (vii) a triple-post-hole vacuum convolute that adds the output currents of the six MITLs, and delivers the combined current to a z-pinch load. The accelerator delivers an effective peak current of 52 MA to a 10-mm-length z pinch that implodes in 95 ns, and 57 MA to a pinch that implodes in 120 ns. The LTD-driven accelerator includes monolithic radial transformers and a MITL system similar to those described above, but does not include intermediate-store transmission lines, multimegavolt gas switches, or a laser trigger system. Instead, this accelerator is driven by 210 LTD modules that include a total of 1 x 10 6 capacitors and 5 x 10 5 200-kV electrically triggered gas switches. The LTD accelerator stores 182 MJ and produces a peak electrical power of 1000 TW. The accelerator delivers an effective peak current of 68 MA to a pinch that implodes in 95 ns, and 75 MA to a pinch that implodes in 120 ns. Conceptually straightforward upgrades to these designs would deliver even higher pinch currents and faster implosions

Engineering feasibility evaluation of a peristaltic pinch

International Nuclear Information System (INIS)

Boicourt, G.P.

1977-04-01

A recent proposal for reducing the end loss of a linear theta pinch is to produce moving magnetic mirrors at the coil ends. The concept entails the sequential pulsing of an axially arranged series of two-turn coaxial coils. The electrical design of such a system presents some unique problems. Ideally, the individual pulse circuits should be completely independent. This would facilitate the design by eliminating interactive effects. In practice, the circuits must be interconnected through isolating inductors to enable the production of a uniform biasing magnetic field. Moreover, the coils must be located physically close together. This produces strong magnetic coupling between the pulse circuits, which can seriously affect the shape and speed of the inward-moving magnetic-mirror field. Possible systems were modeled for the NET-2 circuit analysis code. The models took account of the inductive coupling between the individual circuits in the model. The results show that an increasing magnetic mirror can be produced provided the radius of the theta pinch is not too great compared to the intercoil spacing. The peristaltic field can be maintained for several cycles in the inner coils. The voltage hold-off requirements on the pulse circuit switches are found to be severe, but not impossible to meet

Magnetohydrodynamic effects of current profile control in reversed field pinches

International Nuclear Information System (INIS)

Sovinec, C.R.; Prager, S.C.

1999-01-01

Linear and non-linear MHD computations are used to investigate reversed field pinch configurations with magnetic fluctuations reduced through current profile control. Simulations with reduced ohmic drive and moderate auxiliary current drive, represented generically with an electron force term, applied locally in radius near the plasma edge show magnetic fluctuation energies that are orders of magnitude smaller than those in simulations without profile control. The core of the improved configurations has reduced magnetic shear and closed flux surfaces in some cases, and reversal is sustained through the auxiliary current drive. Modes resonant near the edge may become unstable with auxiliary drive, but their saturation levels can be controlled. The space of auxiliary drive parameters is explored, and the ill effects of deviating far from optimal conditions is demonstrated in non-linear simulations. (author)

Ion heating and MHD dynamo fluctuations in the reversed field pinch

International Nuclear Information System (INIS)

Scime, E.; Hokin, S.; Watts, C.; Mattor, N.

1992-01-01

Ion temperature measurements, time resolved to 10 μs, have been made in the Madison Symmetric Torus reversed-field pinch with a five channel charge exchange analyzer. The ion temperature, T i ∼ 200 eV for I = 350 kA, increases by as much as 100% during discrete dynamo bursts in MST discharges. Magnetic field fluctuations in the range 0.5--5 MHz were also measured. Structure in the fluctuation frequency spectrum at the ion cyclotron frequency appears as the bursts terminate, suggesting that the mechanism of ion heating involves the dissipation of dynamo fluctuations at ion gyro-orbit scales

Characteristics of a large reversed field pinch machine, TPE-RX

International Nuclear Information System (INIS)

Yagi, Y.; Shimada, T.; Hirano, Y.; Sekine, S.; Sakakita, H.; Koguchi, H.; Kiyama, S.; Maejima, Y.; Hirota, I.; Hayase, K.; Sato, Y.; Sugisaki, K.; Oyabu, I.; Hasegawa, M.; Yamane, M.; Sato, F.; Kuno, K.; Minato, T.; Kiryu, A.; Takagi, S.; Sako, K.; Kudough, F.; Urata, K.; Orita, J.; Kaguchi, H.; Sago, H.; Ue, K.

1998-01-01

Construction of a new, large reversed field pinch (RFP) machine called TPE-RX was complete at the end of 1997 as a successor of the previous TPE-1RM20 machine at the Electrotechnical Laboratory (ETL). RFP configuration has been successfully obtained in March 1998. The optimization of the operating condition and discharge cleaning of the wall are presently undergoing with the first physics experiments. This paper is the first report of TPE-RX especially on the goals, overall machine characteristics and the present status. Other papers accompanying with this one will present specific topics on the magnetic coil system and the vacuum vessel system. (author)

Characteristics of a large reversed field pinch machine, TPE-RX

Energy Technology Data Exchange (ETDEWEB)

Yagi, Y.; Shimada, T.; Hirano, Y.; Sekine, S.; Sakakita, H.; Koguchi, H.; Kiyama, S.; Maejima, Y.; Hirota, I.; Hayase, K.; Sato, Y.; Sugisaki, K. [Electrotechnical Lab., Tsukuba-shi, Ibaraki (Japan); Oyabu, I.; Hasegawa, M.; Yamane, M.; Sato, F.; Kuno, K.; Minato, T.; Kiryu, A.; Takagi, S.; Sako, K. [Mitsubishi Electric Corp. (Japan); Kudough, F.; Urata, K.; Orita, J.; Kaguchi, H.; Sago, H.; Ue, K. [Mitsubishi Heavy Industries Ltd. (Japan)

1998-07-01

Construction of a new, large reversed field pinch (RFP) machine called TPE-RX was complete at the end of 1997 as a successor of the previous TPE-1RM20 machine at the Electrotechnical Laboratory (ETL). RFP configuration has been successfully obtained in March 1998. The optimization of the operating condition and discharge cleaning of the wall are presently undergoing with the first physics experiments. This paper is the first report of TPE-RX especially on the goals, overall machine characteristics and the present status. Other papers accompanying with this one will present specific topics on the magnetic coil system and the vacuum vessel system. (author)

Time resolved EUV spectra from Zpinching capillary discharge plasma

Science.gov (United States)

Jancarek, Alexandr; Nevrkla, Michal; Nawaz, Fahad

2015-09-01

We developed symmetrically charged driver to obtain high voltage, high current Z-pinching capillary discharge. Plasma is created by up to 70 kA, 29 ns risetime current pulse passing through a 5 mm inner diameter, 224 mm long capillary filled with gas to initial pressure in the range of 1 kPa. Due to the low inductance design of the driver, the pinch is observable directly from the measured current curve. Time-integrated and time-resolved spectra of discharge plasma radiation are recorded together with the capillary current and analyzed. The most encouraging spectra were captured in the wavelength range 8.3 ÷ 14 nm. This spectral region contains nitrogen Balmer series lines including potentially lasing NVII 2 - 3 transition. Spectral lines are identified in the NIST database using the FLY kinetic code. The line of 13.38 nm wavelength, transition NVII 2 - 3, was observed in gated, and also in time-integrated spectra for currents >60 kA. This work has been supported by the Ministry of Education, Youth and Sports of the Czech Republic grants LG13029.

On the stability limits of the Pinch-conductor current ratio in Extrap

International Nuclear Information System (INIS)

Lehnert, B.

1987-12-01

A first attempt is made to take the special stability features of the Extrap confinement scheme into account, thereby including kinetic large Larmor radius (LLR) effects. This approach predicts Extrap to be unstable outside a domain defined by a lower and an upper ratio a - /a x is related to the ratio J p /J v between the pinch current J p and the conductor current J v . Stability within the predicted domain seems to agree with so far performed linear and toroidal experiments, and can explain the observed increase in J p /J v and in the plasma temperature, in terms of an increased ratio a - /a x . According to present analysis, an optimum value of the conductor current J v should further exist with respect to pinch equilibrium and stability, as given by the condition a - approx = a x . (author)

Experimental study on gas-puff Z-pinch load characteristics on yang accelerator

International Nuclear Information System (INIS)

Ren Xiaodong; Huang Xianbin; Yang Libing; Dan Jiakun; Duan Shuchao; Zhang Zhaohui; Zhou Shaotong

2010-01-01

A supersonic single-shell gas-puff load has been developed for Z-pinch experiments on 'Yang' accelerator. Using a fast responding pressure probe to measure the supersonic gas flow, impact pressure at different position and plenum pressure were acquired, which were combined with gas dynamics formulas to determine gas pressures and densities. The radial density profile displays that positions of gas shell varies with axial position, and the gas densities on axis increases as the distance from nozzle increases. Integral radial densities indicates that the linear mass density peaks at nozzle exit and decreases as increasing the distance from nozzle. Using single-shell supersonic gas-puff load, Z-pinch implosion experiments were performed on 'Yang' accelerator. Primary analysis of implosion process was presented, and computational trajectories of imploding plasma shell using snowplow model are in agreement with the experimental results. (authors)

Neutron energy distribution function reconstructed from time-of-flight signals in deuterium gas-puff Z-pinch

Czech Academy of Sciences Publication Activity Database

Klír, D.; Kravárik, J.; Kubeš, J.; Rezac, K.; Ananev, S.S.; Bakshaev, Y. L.; Blinov, P. I.; Chernenko, A. S.; Kazakov, E.D.; Korolev, V. D.; Ustroev, G. I.; Juha, Libor; Krása, Josef; Velyhan, Andriy

2009-01-01

Roč. 37, č. 3 (2009), s. 425-432 ISSN 0093-3813 R&D Projects: GA MŠk(CZ) LC528; GA MŠk LA08024 Grant - others:IAEA(XE) RC 14817 Institutional research plan: CEZ:AV0Z10100523 Keywords : deuterium * fusion reaction * gas puff * Monte Carlo reconstruction * neutron energy spectra * neutron s * Z-pinch Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 1.043, year: 2009

Energy Conversion in Imploding Z-Pinch Plasma

International Nuclear Information System (INIS)

Fisher, V.I.; Gregorian, L.; Davara, G.; Kroupp, E.; Bernshtam, V.A.; Ralchenko, Yu. V.; Starobinets, A.; Maron, Y.

2002-01-01

Due to important applications, Z-pinches became a subject of extensive studies. In these studies, main attention is directed towards improvement in efficiency of electric energy conversion into high-power radiation burst. At present, knowledge available on physics of Z-pinch operation, plasma motion, atomic kinetics, and energy conversion is mainly knowledge of numerical simulation results. We believe further progress require (i) experimental determination of spatial distribution and time history of thermodynamic parameters and magnetic field, as well as (ii) utilization of this data for experiment-based calculation of r,t-distribution of driving forces, mass and energy fluxes, and local energy deposition rates due to each of contributing mechanisms, what provides an insight into a process of conversion of stored electric energy into radiation burst. Moreover, experimentally determined r, t-distribution of parameters may serve for verification of computer programs developed for simulation of Z-pinch operation and optimization of radiation output. Within this research program we performed detailed spectroscopic study of plasmas imploding in modest-size (25 kV, 5 kJ, 1.2 μs quaterperiod) gas-puff Z-pinch. This facility has reasonably high repetition rate and provides good reproducibility of results. Consistent with plasma ionization degree in the implosion period, measurements are performed in UV-visible spectral range. Observation of spectral lines emitted at various azimuthal angles f showed no dependence on f. Dependence on axial coordinate z is found to be weak in near-anode half of the anode-cathode gap. Based on these observations and restricting the measurements to near-anode half of the gap, an evolution of parameters is studied in time and radial coordinate r only. In present talk we report on determination of radial component of plasma hydrodynamic velocity u r (r,t), magnetic field B ζ (r,t), electron density n e (r,t), density of ions in various

Radiation hydrodynamics of z-pinch plasmas

International Nuclear Information System (INIS)

Davis, J.

1993-01-01

Over the years there has been a sustained interest in and fascination with Z-pinch plasmas. Whether the interest is in radiation source development, fusion plasmas, or basic research there exits an extensive bibliography of literature promulgating and perpetuating a variety of claims regarding the performance of Z-pinch plasmas. In this paper an attempt will be made to present a coherent picture of the documented and commonly held views for a class of Z-pinch plasmas concerned primarily with soft x-ray radiation source development. Many of the issues and findings are common to Z-pinch plasmas in general but the attention here will be focused on gas puffs and multiple wire arrays. The role and importance of radiation on the dynamics and the interplay between the radiation and the dynamics will also be presented and discussed. A number of comparisons with experimental results will be made with 0-, 1-, and 2-D numerical simulations for several pulsed power drivers ranging in current from several mega-amps to 10's of mega-amps for a variety of risetimes and load materials

Reversed field pinch operation with intelligent shell feedback control in EXTRAP T2R

Science.gov (United States)

Brunsell, P. R.; Kuldkepp, M.; Menmuir, S.; Cecconello, M.; Hedqvist, A.; Yadikin, D.; Drake, J. R.; Rachlew, E.

2006-11-01

Discharges in the thin shell reversed field pinch (RFP) device EXTRAP T2R without active feedback control are characterized by growth of non-resonant m = 1 unstable resistive wall modes (RWMs) in agreement with linear MHD theory. Resonant m = 1 tearing modes (TMs) exhibit initially fast rotation and the associated perturbed radial fields at the shell are small, but eventually TMs wall-lock and give rise to a growing radial field. The increase in the radial field at the wall due to growing RWMs and wall-locked TMs is correlated with an increase in the toroidal loop voltage, which leads to discharge termination after 3-4 wall times. An active magnetic feedback control system has been installed in EXTRAP T2R. A two-dimensional array of 128 active saddle coils (pair-connected into 64 independent m = 1 coils) is used with intelligent shell feedback control to suppress the m = 1 radial field at the shell. With feedback control, active stabilization of the full toroidal spectrum of 16 unstable m = 1 non-resonant RWMs is achieved, and TM wall locking is avoided. A three-fold extension of the pulse length, up to the power supply limit, is observed. Intelligent shell feedback control is able to maintain the plasma equilibrium for 10 wall times, with plasma confinement parameters sustained at values comparable to those obtained in thick shell devices of similar size.

Reversed field pinch operation with intelligent shell feedback control in EXTRAP T2R

International Nuclear Information System (INIS)

Brunsell, P.R.; Kuldkepp, M.; Menmuir, S.; Cecconello, M.; Hedqvist, A.; Yadikin, D.; Drake, J.R.; Rachlew, E.

2006-01-01

Discharges in the thin shell reversed field pinch (RFP) device EXTRAP T2R without active feedback control are characterized by growth of non-resonant m = 1 unstable resistive wall modes (RWMs) in agreement with linear MHD theory. Resonant m = 1 tearing modes (TMs) exhibit initially fast rotation and the associated perturbed radial fields at the shell are small, but eventually TMs wall-lock and give rise to a growing radial field. The increase in the radial field at the wall due to growing RWMs and wall-locked TMs is correlated with an increase in the toroidal loop voltage, which leads to discharge termination after 3-4 wall times. An active magnetic feedback control system has been installed in EXTRAP T2R. A two-dimensional array of 128 active saddle coils (pair-connected into 64 independent m = 1 coils) is used with intelligent shell feedback control to suppress the m = 1 radial field at the shell. With feedback control, active stabilization of the full toroidal spectrum of 16 unstable m = 1 non-resonant RWMs is achieved, and TM wall locking is avoided. A three-fold extension of the pulse length, up to the power supply limit, is observed. Intelligent shell feedback control is able to maintain the plasma equilibrium for 10 wall times, with plasma confinement parameters sustained at values comparable to those obtained in thick shell devices of similar size

Hybrid Z-Θ Pinches with fused capacitor banks

International Nuclear Information System (INIS)

Grandey, R.; Gersten, M.; Loter, N.; Rauch, J.; Rostoker, N.; Thompson, W.; Ware, K.

1987-01-01

The Hybrid Z-Θ Pinch circuit equations in the thin shell model were reexamined to see what advantages can be obtained by using a fused, high-energy (>--1MJ) bank driver. The DNA ACE facility at MLI utilizes a 36 μF capacitor band which can be charged to 120 kV to provide 250 kJ of stored energy. This configuration appears to be very appropriate to test the performance of a hybrid-stabilized fused-bank driven pinch. The circuit analyses suggest that the energy transfer efficiency from the bank to a pinched plasma can be increased from less than 1%, for a nonfused bank, to about 10% for a fused configuration. In the applicable region of parameter space, the Hybrid Pinch does not increase the efficiency of energy transfer into the plasma over that obtainable from a Z-pinch. The additional stability may allow larger initial radii to be used with concomitant improved coupling into radiation above 1 keV

ExB flow shear and enhanced confinement in the Madison Symmetric Torus reversed-field pinch

International Nuclear Information System (INIS)

Chapman, B.E.; Almagri, A.F.; Anderson, J.K.; Chiang, C.; Craig, D.; Fiksel, G.; Lanier, N.E.; Prager, S.C.; Sarff, J.S.; Stoneking, M.R.; Terry, P.W.

1998-01-01

Strong ExB flow shear occurs in the edge of three types of enhanced confinement discharge in the Madison Symmetric Torus [Dexter et al., Fusion Technol. 19, 131 (1991)] reversed-field pinch. Measurements in standard (low confinement) discharges indicate that global magnetic fluctuations drive particle and energy transport in the plasma core, while electrostatic fluctuations drive particle transport in the plasma edge. This paper explores possible contributions of ExB flow shear to the reduction of both the magnetic and electrostatic fluctuations and, thus, the improved confinement. In one case, shear in the ExB flow occurs when the edge plasma is biased. Biased discharges exhibit changes in the edge electrostatic fluctuations and improved particle confinement. In two other cases, the flow shear emerges (1) when auxiliary current is driven in the edge and (2) spontaneously, following sawtooth crashes. Both edge electrostatic and global magnetic fluctuations are reduced in these discharges, and both particle and energy confinement improve. copyright 1998 American Institute of Physics

Transverse equilibria in linear collider beam-beam collisions

International Nuclear Information System (INIS)

Rosenzweig, J.B.; Chen, Pisin

1991-01-01

It has been observed in simulations of the beam-beam interaction in linear colliders that a near equilibrium pinched state of the colliding beams develops when the disruption parameter is large (D much-gt 1). In this state the beam transverse density distributions are peaked at center, with long tails. The authors present here an analytical model of the equilibrium approached by the beams, that of a generalized Bennett pinch which develops through collisionless damping due to the strong nonlinearity of the beam-beam interaction. In order to calculate the equilibrium pinched beam size, an estimation of the rms emittance growth is made which takes into account the partial adiabaticity of the collision. This pinched beam size is used to derive the luminosity enhancement factors whose scaling is in agreement with the simulation results for both D and thermal factor A = σ z /β * large, and explains the previously noted cubic relationship between round and flat beam enhancement factors

Self-Consolidation Mechanism of Nanostructured Ti5Si3 Compact Induced by Electrical Discharge

Directory of Open Access Journals (Sweden)

W. H. Lee

2015-01-01

Full Text Available Electrical discharge using a capacitance of 450 μF at 7.0 and 8.0 kJ input energies was applied to mechanical alloyed Ti5Si3 powder without applying any external pressure. A solid bulk of nanostructured Ti5Si3 with no compositional deviation was obtained in times as short as 159 μsec by the discharge. During an electrical discharge, the heat generated is the required parameter possibly to melt the Ti5Si3 particles and the pinch force can pressurize the melted powder without allowing the formation of pores. Followed rapid cooling preserved the nanostructure of consolidated Ti5Si3 compact. Three stepped processes during an electrical discharge for the formation of nanostructured Ti5Si3 compact are proposed: (a a physical breakdown of the surface oxide of Ti5Si3 powder particles, (b melting and condensation of Ti5Si3 powder by the heat and pinch pressure, respectively, and (c rapid cooling for the preservation of nanostructure. Complete conversion yielding a single phase Ti5Si3 is primarily dominated by the solid-liquid mechanism.

Plasma-column instabilities in a reversed-field pinch without a shell

Energy Technology Data Exchange (ETDEWEB)

Schmid, P.G.

1988-01-01

Plasma column instabilities in a Reversed Field Pinch (RFP) without a shell were investigated in the Colorado Reversatron RFP. The Reversatron RFP (aspect ration R/a = 50 cm/8cm) is a toroidal plasma containment device consisting of a vacuum chamber, a thick conducting shell, modular shells, magnetic field producing coils and diagnostics to characterize the plasma. RFP discharges were set up in the Reversatron in three different experimental configurations: with a thick conducting shell, with a modular shell and with no shell. In two of the configurations, a shell enclosed the plasma column to provide some plasma stability. A vertical magnetic field provided equilibrium in experiments without a shell. Data from discharges without a shell indicated that the plasma duration was greatly reduced and the plasma resistance increased compared to the discharges with a thick shell. Plasma position probes indicated large plasma centriod displacements corresponding to a n = 1 and a n = 3 kink coincident with the peak of the plasma current and the start of a discharge termination phase. The modular shell lengthened the discharge duration and lowered the plasma resistance to values intermediate between the plasma with a thick shell and the plasma with no shell. The modular shell suppressed the large plasma column displacements observed in the RFP plasma without a shell.

Plasma-column instabilities in a reversed-field pinch without a shell

International Nuclear Information System (INIS)

Schmid, P.G.

1988-01-01

Plasma column instabilities in a Reversed Field Pinch (RFP) without a shell were investigated in the Colorado Reversatron RFP. The Reversatron RFP (aspect ration R/a = 50 cm/8cm) is a toroidal plasma containment device consisting of a vacuum chamber, a thick conducting shell, modular shells, magnetic field producing coils and diagnostics to characterize the plasma. RFP discharges were set up in the Reversatron in three different experimental configurations: with a thick conducting shell, with a modular shell and with no shell. In two of the configurations, a shell enclosed the plasma column to provide some plasma stability. A vertical magnetic field provided equilibrium in experiments without a shell. Data from discharges without a shell indicated that the plasma duration was greatly reduced and the plasma resistance increased compared to the discharges with a thick shell. Plasma position probes indicated large plasma centriod displacements corresponding to a n = 1 and a n = 3 kink coincident with the peak of the plasma current and the start of a discharge termination phase. The modular shell lengthened the discharge duration and lowered the plasma resistance to values intermediate between the plasma with a thick shell and the plasma with no shell. The modular shell suppressed the large plasma column displacements observed in the RFP plasma without a shell

Preliminary results from the flow-through z-pinch experiments: ZaP

International Nuclear Information System (INIS)

Shumlak, U.; Nelson, B.A.; Goilingo, R.P.; Tang, D.; Crawford, E.; Hartog, D.J.D.; Holly, D.J.

1999-01-01

The stabilizing effect of an axial flow on the m = 1 kink instability in z-pinches has been studied numerically by reducing the linearized ideal MHD equations to a one-dimensional eigenvalue equation for the radial displacement. A diffuse z-pinch equilibrium is chosen that is made marginally stable to the m = 0 sausage mode by tailoring the pressure profile. The principal result reveals that a sheared axial flow does stabilize the kink mode when the shear exceeds a threshold value which is inversely proportional to the wavelength of the mode. This threshold value can be satisfied with a peak flow which is less than the Alfven speed for certain wavelengths. Additionally, the m = 0 sausage mode is driven from marginal stability into the stable regime which suggests that the equilibrium pressure profile control can be relaxed. The flow stabilization agrees with experimental observations. The details of the theoretical development will be presented

Energy balance in a Z pinch with suppressed Rayleigh-Taylor instability

Science.gov (United States)

Baksht, R. B.; Oreshkin, V. I.; Rousskikh, A. G.; Zhigalin, A. S.

2018-03-01

At present Z-pinch has evolved into a powerful plasma source of soft x-ray. This paper considers the energy balance in a radiating metallic gas-puff Z pinch. In this type of Z pinch, a power-law density distribution is realized, promoting suppression of Rayleigh-Taylor (RT) instabilities that occur in the pinch plasma during compression. The energy coupled into the pinch plasma, is determined as the difference between the total energy delivered to the load from the generator and the magnetic energy of the load inductance. A calibrated voltage divider and a Rogowski coil were used to determine the coupled energy and the load inductance. Time-gated optical imaging of the pinch plasma showed its stable compression up to the stagnation phase. The pinch implosion was simulated using a 1D two-temperature radiative magnetohydrodynamic code. Comparison of the experimental and simulation results has shown that the simulation adequately describes the pinch dynamics for conditions in which RT instability is suppressed. It has been found that the proportion of the Ohmic heating in the energy balance of a Z pinch with suppressed RT instability is determined by Spitzer resistance and makes no more than ten percent.

On the instability increments of a stationary pinch

International Nuclear Information System (INIS)

Bud'ko, A.B.

1989-01-01

The stability of stationary pinch to helical modes is numerically studied. It is shown that in the case of a rather fast plasma pressure decrease to the pinch boundary, for example, for an isothermal diffusion pinch with Gauss density distribution instabilities with m=0 modes are the most quickly growing. Instability increments are calculated. A simple analytical expression of a maximum increment of growth of sausage instability for automodel Gauss profiles is obtained

Effect of wire shape on wire array discharge

International Nuclear Information System (INIS)

Shimomura, N.; Tanaka, Y.; Yushita, Y.; Nagata, M.; Teramoto, Y.; Katsuki, S.; Akiyama, H.

2001-01-01

Although considerable investigations have been reported on z-pinches to achieve nuclear fusion, little attention has been given from the point of view of how a wire array consisting of many parallel wires explodes. Instability existing in the wire array discharge has been shown. In this paper, the effect of wire shape in the wire array on unstable behavior of the wire array discharge is represented by numerical analysis. The claws on the wire formed in installation of wire may cause uniform current distribution on wire array. The effect of error of wire diameter in production is computed by Monte Carlo Method. (author)

Effect of wire shape on wire array discharge

Energy Technology Data Exchange (ETDEWEB)

Shimomura, N.; Tanaka, Y.; Yushita, Y.; Nagata, M. [University of Tokushima, Department of Electrical and Electronic Engineering, Tokushima (Japan); Teramoto, Y.; Katsuki, S.; Akiyama, H. [Kumamoto University, Department of Electrical and Computer Engineering, Kumamoto (Japan)

2001-09-01

Although considerable investigations have been reported on z-pinches to achieve nuclear fusion, little attention has been given from the point of view of how a wire array consisting of many parallel wires explodes. Instability existing in the wire array discharge has been shown. In this paper, the effect of wire shape in the wire array on unstable behavior of the wire array discharge is represented by numerical analysis. The claws on the wire formed in installation of wire may cause uniform current distribution on wire array. The effect of error of wire diameter in production is computed by Monte Carlo Method. (author)

On the Heating of Ions in Noncylindrical Z-Pinches

Science.gov (United States)

Svirsky, E. B.

2018-01-01

The method proposed here for analyzing processes in a hot plasma of noncylindrical Z-pinches is based on separation of the group of high-energy ions into a special fraction. Such ions constitute an insignificant fraction ( 10%) of the total volume of the Z-pinch plasma, but these ions contribute the most to the formation of conditions in which the pinch becomes a source of nuclear fusion products and X-ray radiation. The method allows a quite correct approach to obtaining quantitative estimates of the plasma parameters, the nuclear fusion energy yield, and the features of neutron fluxes in experiments with Z-pinches.

Self-organisation and intermittent coherent oscillations in the EXTRAP T2 reversed field pinch

International Nuclear Information System (INIS)

Cecconello, M.; Malmberg, J.A.; Sallander, E.; Drake, J.R.

2002-01-01

Many reversed-field pinch (RFP) experiments exhibit a coherent oscillatory behaviour that is characteristic of discrete dynamo events and is associated with intermittent current profile self-organisation phenomena. However, in the vast majority of the discharges in the resistive shell RFP experiment EXTRAP T2, the dynamo activity does not show global, coherent oscillatory behaviour. The internally resonant tearing modes are phase-aligned and wall-locked resulting in a large localised magnetic perturbation. Equilibrium and plasma parameters have a level of high frequency fluctuations but the average values are quasi-steady. For some discharges, however, the equilibrium parameters exhibit the oscillatory behaviour characteristic of the discrete dynamo events. For these discharges, the trend observed in the tearing mode spectra, associated with the onset of the discrete relaxation event behaviour, is a relative higher amplitude of m = 0 mode activity and relative lower amplitude of the m = 1 mode activity compared with their average values. Global plasma parameters and model profile calculations for sample discharges representing the two types of relaxation dynamics are presented

Self-Organisation and Intermittent Coherent Oscillations in the EXTRAP T2 Reversed Field Pinch

Science.gov (United States)

Cecconello, M.; Malmberg, J.-A.; Sallander, E.; Drake, J. R.

Many reversed-field pinch (RFP) experiments exhibit a coherent oscillatory behaviour that is characteristic of discrete dynamo events and is associated with intermittent current profile self-organisation phenomena. However, in the vast majority of the discharges in the resistive shell RFP experiment EXTRAP T2, the dynamo activity does not show global, coherent oscillatory behaviour. The internally resonant tearing modes are phase-aligned and wall-locked resulting in a large localised magnetic perturbation. Equilibrium and plasma parameters have a level of high frequency fluctuations but the average values are quasi-steady. For some discharges, however, the equilibrium parameters exhibit the oscillatory behaviour characteristic of the discrete dynamo events. For these discharges, the trend observed in the tearing mode spectra, associated with the onset of the discrete relaxation event behaviour, is a relative higher amplitude of m = 0 mode activity and relative lower amplitude of the m = 1 mode activity compared with their average values. Global plasma parameters and model profile calculations for sample discharges representing the two types of relaxation dynamics are presented.

Pinches and micropinches in the SPEED 2 plasma focus

Energy Technology Data Exchange (ETDEWEB)

Roewekamp, P; Decker, G; Kies, W; Lucas, B; Schmitz, F; Ziethen, G [Heinrich-Heine-Univ., Duesseldorf (Germany). Institut fuer Experimentalphysik; Simanovskij, D M; Bobashev, S V [Russian Academy of Sciences, St. Petersburg (Russian Federation). A.F. Ioffe Physico-Technical Inst.

1997-12-31

The discharges in the SPEED 2 Plasma Focus as well as other pinch plasmas generated in a plasma focus configuration exhibit two different modes. The micropinch mode is experimentally investigated in detail and well theoretically modelled. Therefore its characteristics e.g. temperature, density, life time and energy output are well known. Nevertheless the micropinches appear very erratic in space and time and their optimization and application is rather difficult. In contrast to this the column mode is not equally well understood yet. Its remarkable features are the unexpectedly high stability (also if the critical current for radiative collapse is exceeded) and its reproducibility, which are important for applications in soft x-ray microscopy or lithography. (J.U.). 6 figs., 9 refs.

The effect of sheared axial flow on nonlinear Z-pinch dynamics

International Nuclear Information System (INIS)

Kassapakis, N.

2000-01-01

A two dimensional Eulerian fluid code has been used to study three problems related to Z-pinch and laser produced plasmas. a) The nonlinear evolution of a localised m=0 MHD mode neck is studied in order to extract some scaling laws for the size and form of the artificial neck. We examine whether the ubiquitous m=0 instability could be beneficially used to assist in the formation of a transient localised dense plasma. The results obtained were in satisfactory agreement with experiments and other theoretical work where available. b) The development of the m=0 instability on a Z-pinch although beneficial in the previous case, is detrimental from a stability point of view and thus to the utilisation of the device as a fusion reactor by itself. This is because the timescales of the instability development are faster than the confinement time needed for fusion to occur. Sheared axial flow is a proposed mechanism for the non-linear saturation of this particular instability. Indeed the linear growth rate also can be substantially reduced. It is hoped that it can inhibit the growth of the instabilities or at least delay their development sufficiently for fusion to take place. The numerical study of the effect of sheared axial flow on the nonlinear dynamics of the Z-pinch carried out, demonstrates that sheared flow with velocity u z z >4 Alfven speed other modes, of the Kelvin-Helmholtz type, are excited which take over from the fastest growing mode in the static case. c) The expansion of the ablated plasma in laser-solid interactions is an important phenomenon for a plethora of reasons one of which is ICF. The simulations were in direct agreement with previous experimental work regarding the bulk properties of the ablation surface. They also provided justification for some assumptions made during the analysis of the observations and helped to confirm the calibration of the diagnostics timewise. The most striking feature of the experiments, namely the density dip on the

Parametric dependences of momentum pinch and Prandtl number in JET

DEFF Research Database (Denmark)

Tala, T.; Salmi, A.; Angioni, C.

2011-01-01

Several parametric scans have been performed to study momentum transport on JET. A neutral beam injection modulation technique has been applied to separate the diffusive and convective momentum transport terms. The magnitude of the inward momentum pinch depends strongly on the inverse density...... gradient length, with an experimental scaling for the pinch number being -Rvpinch/χφ = 1.2R/Ln +1.4. There is no dependence of the pinch number on collisionality, whereas the pinch seems to depend weakly on q-profile, the pinch number decreasing with increasing q. The Prandtl number was not found to depend...... either on R/Ln, collisionality or on q. The gyro-kinetic simulations show qualitatively similar dependence of the pinch number on R/Ln, but the dependence is weaker in the simulations. Gyro-kinetic simulations do not find any clear parametric dependence in the Prandtl number, in agreement...

Proposal for the ZT-40 reversed-field Z-pinch experiment

International Nuclear Information System (INIS)

Baker, D.A.; Machalek, M.D.

1977-08-01

A next-generation, toroidal, reversed-field Z-pinch experiment to be constructed at LASL is proposed. On the basis of encouraging ZT-I and ZT-S experimental results, a larger device with a 40-cm bore and a 114-cm major radius is proposed, to extend the confinement time by about an order of magnitude. The new experiment will explore the physics of programming reversed-field pinches in a size range unexplored by previous reversed-field pinch experiments. Model reversed-field pinch reactor calculations show that, if stability is assumed, small fusion reactors are possible if the pinch current density is high. A basic aim will be to delineate the plasma and current density ranges in which stable reversed-field pinches can be produced. Improved vacuum techniques will be used to overcome the radiation losses that probably kept electron temperatures low in the earlier, smaller experiments

Dose-current discharge correlation analysis in a Mather type Plasma Focus device for medical applications

Science.gov (United States)

Sumini, M.; Mostacci, D.; Tartari, A.; Mazza, A.; Cucchi, G.; Isolan, L.; Buontempo, F.; Zironi, I.; Castellani, G.

2017-11-01

In a Plasma Focus device the plasma collapses into the pinch where it reaches thermonuclear conditions for a few tens of nanoseconds, becoming a multi-radiation source. The nature of the radiation generated depends on the gas filling the chamber and the device working parameters. The self-collimated electron beam generated in the backward direction with respect to the plasma motion is one of the main radiation sources of interest also for medical applications. The electron beam may be guided against a high Z material target to produce an X-ray beam. This technique offers an ultra-high dose rate source of X-rays, able to deliver during the pinch a massive dose (up to 1 Gy per discharge for the PFMA-3 test device), as measured with EBT3 GafchromicⒸfilm tissue equivalent dosimeters. Given the stochastic behavior of the discharge process, a reliable on-line estimate of the dose-delivered is a very challenging task, in some way preventing a systematic application as a potentially interesting therapy device. This work presents an approach to linking the dose registered by the EBT3 GafchromicⒸfilms with the information contained in the signal recorded during the current discharge process. Processing the signal with the Wigner-Ville distribution, a spectrogram was obtained, displaying the information on intensity at various frequency scales, identifying the band of frequencies representative of the pinch events and define some patterns correlated with the dose.

Linear MHD equilibria

International Nuclear Information System (INIS)

Scheffel, J.

1984-03-01

The linear Grad-Shafranov equation for a toroidal, axisymmetric plasma is solved analytically. Exact solutions are given in terms of confluent hyper-geometric functions. As an alternative, simple and accurate WKBJ solutions are presented. With parabolic pressure profiles, both hollow and peaked toroidal current density profiles are obtained. As an example the equilibrium of a z-pinch with a square-shaped cross section is derived.(author)

Kinetic simulation of neutron production in a deuterium z-pinch

International Nuclear Information System (INIS)

Mostrom, C.; Stygar, William A.; Thoma, Carsten; Welch, Dale Robert; Clark, R.E.; Leeper, Ramon Joe; Rose, David V.

2010-01-01

We have found computationally that, at sufficiently high currents, half of the neutrons produced by a deuterium z pinch are thermonuclear in origin. Early experiments below 1-MA current found that essentially all of the neutrons produced by a deuterium pinch are not thermonuclear, but are initiated by an instability that creates beam-target neutrons. Many subsequent authors have supported this result while others have claimed that pinch neutrons are thermonuclear. To resolve this issue, we have conducted fully kinetic, collisional, and electromagnetic simulations of the complete time evolution of a deuterium pinch. We find that at 1-MA pinch currents, most of the neutrons are, indeed, beam-target in origin. At much higher current, half of the neutrons are thermonuclear and half are beam-target driven by instabilities that produce a power law fall off in the ion energy distribution function at large energy. The implications for fusion energy production with such pinches are discussed.

Current redistribution and generation of kinetic energy in the stagnated Z pinch.

Science.gov (United States)

Ivanov, V V; Anderson, A A; Papp, D; Astanovitskiy, A L; Talbot, B R; Chittenden, J P; Niasse, N

2013-07-01

The structure of magnetic fields was investigated in stagnated wire-array Z pinches using a Faraday rotation diagnostic at the wavelength of 266 nm. The distribution of current in the pinch and trailing material was reconstructed. A significant part of current can switch from the main pinch to the trailing plasma preheated by x-ray radiation of the pinch. Secondary implosions of trailing plasma generate kinetic energy and provide enhanced heating and radiation of plasma at stagnation. Hot spots in wire-array Z pinches also provide enhanced radiation of the Z pinch. A collapse of a single hot spot radiates 1%-3% of x-ray energy of the Z pinch with a total contribution of hot spots of 10%-30%.

Rectangular waveform linear transformer driver module design

International Nuclear Information System (INIS)

Zhao Yue; Xie Weiping; Zhou Liangji; Chen Lin

2014-01-01

Linear Transformer Driver is a novel pulsed power technology, its main merits include a parallel LC discharge array and Inductive Voltage Adder. The parallel LC discharge array lowers the whole circuit equivalent inductance and the Inductive Voltage Adder unites the modules in series in order to create a high electric field grads, meanwhile, restricts the high voltage in a small space. The lower inductance in favor of LTD output a fast waveform and IVA confine high voltage in secondary cavity. In recently, some LTD-based pulsed power system has been development yet. The usual LTD architecture provides damped sine shaped output pulses that may not be suitable in flash radiography, high power microwave production, z-pinch drivers, and certain other applications. A more suitable driver output pulse would have a flat or inclined top (slightly rising or falling). In this paper, we present the design of an LTD cavity that generates this type of the output pulse by including within its circular array some number of the harmonic bricks in addition to the standard bricks according to Fourier progression theory. The parallel LC discharge array circuit formula is introduced by Kirchhoff Law, and the sum of harmonic is proofed as an analytic result, meanwhile, rationality of design is proved by simulation. Varying gas spark discharge dynamic resistance with harmonic order and switches jitter are analyzed. The results are as following: The more harmonic order is an approach to the ideal rectangular waveform, but lead to more system complexity. The capacity decreases as harmonic order increase, and gas spark discharge dynamic resistance rises with the capacity. The rising time protracts and flat is decay or even vanishes and the shot to shot reproducibility is degenerate as the switches jitter is high. (authors)

Development of Rayleigh-Taylor and bulk convection instabilities in the dynamics of plasma liners and pinches

International Nuclear Information System (INIS)

Bud'ko, A.B.; Velikovich, A.L.; Liberman, M.A.; Felber, F.S.

1989-01-01

A solution is derived for the problem of the initial, linear stage of the growth of small perturbations in the course of the cylindrically symmetric compression and expansion of a plasma liner and a Z-pinch with a sharp boundary. In these systems, Rayleigh-Taylor instabilities localized near the plasma boundaries are the most dangerous. Bulk convective instabilities develop in addition to these Rayleigh-Taylor instabilities. The various instability modes, including local and global Rayleigh-Taylor modes, which grown in an accelerated plasma with distributed profiles of hydrodynamic variables, are classified. The spectra of the instability growth rates are calculated for plasma liners and Z-pinches. The shape of these spectra reveals an explanation of the stratification and filamentation of the plasma observed experimentally in pinches and liners. The imposition of a longitudinal magnetic field gives rise to a stability window in the space of the flow parameters. In this window, the Rayleigh-Taylor modes are suppressed completely by magnetic shear, while the bulk convective modes are suppressed to a significant extent

Self-similar oscillations of the Extrap pinch

International Nuclear Information System (INIS)

Tendler, M.

1987-11-01

The method of the dynamic stabilization is invoked to explain the enhanced stability of a Z-pinch in EXTRAP configuration. The oscillatory motion is assumed to be forced on EXTRAP due to self-similar oscillations of a Z-pinch. Using a scaling for the net energy loss with plasma density and temperature typical for divertor configurations, a new analytic, self-similar solution of the fluid equations is presented. Strongly unharmonic oscillations of the plasma parameters in the pinch arise. These results are used in a discussion on the stability of EXTRAP, considered as a system with a time dependent internal magnetic field. The effect of the dynamic stabilization is considered by taking estimates. (author)

Theory of Rapid Formation of Pedestal and Pedestal width due to Anomalous Particle Pinch in the Edge of H-mode Discharges

Energy Technology Data Exchange (ETDEWEB)

Kaw, P.K., E-mail: kaw@ipr.res.in [Institute for Plasma Research, Bhat (India); Singh, R. [Institute for Plasma Research, Bhat (India); ITER Organization, Saint Paul-lez-Durance [France; Nordman, H. [Chamlers Institute of Technology, Goteborg (Sweden); Garbet, X.; Bourdelle, C. [CEA, Saint Paul-lez-Durance (France); Campbell, D.; Loarte, A.; Bora, D. [ITER Organization, Saint Paul-lez-Durance (France)

2012-09-15

Full text: A theory based on a turbulent particle pinch is proposed to explain the rapid formation of sharp density gradients in tokamak edge plasmas, in particular the pedestal region. The inward radial particle flux in the pedestal results from the interaction between small scale electron temperature gradient driven (ETG) turbulence and self-consistently formed 'electron geodesic acoustic modes' (el-GAMs). To address this phenomenon, the el-GAM modulational instability driven by the ETG turbulence background is studied. The ETG level of fluctuations and particle pinch are estimated through the back reaction of eGAMs on ETG turbulence. It is found that the particle pinch is quite sensitive to magnetic shear, safety factor, ratio of electron to ion temperatures and atomic mass number. In the absence of particle source in the pedestal, the density gradient length scale, of the order of the pedestal width, is estimated. It is shown that it is proportional to the major radius, up to some dependence on the poloidal beta. Moreover it does not depend on the normalized gyro-radius. This scaling agrees with DIII-D and JET similarity experiments. This dependence is favorable when extrapolated to the pedestal width in ITER in spite of its low normalized gyro radius. It is also shown that the density scale length becomes sharper by increasing the magnetic shear. A new H-mode pedestal pressure scaling is derived assuming that the pressure gradient is limited by the ballooning instability. (author)

Growth of Rayleigh-Taylor and bulk convective instabilities in dynamics of plasma liners and pinches

International Nuclear Information System (INIS)

Bud'ko, A.B.; Velikovich, A.L.; Liberman, M.A.; Felber, F.S.

1989-01-01

Perturbation growth is studied for the initial, linear stage of an instability development in the course of a cylindrically-symmetric compression and expansion of plasma liners and Z-pinches with a sharp boundary. The hydrodynamic instabilities are Rayleigh-Taylor and bulk convective ones, the former being the most dengerous. Classification of the instability modes developing in accelerated plasmas, inclusing the local and global Rayleigh-Taylor modes, is given. The spectra of the instability growth rates are calculated for plasma liners and Z-pinches. The properties of the spectra appear to explain the filamentation and stratification of plasmas observed in the experiments with liners and Z-pinches. An axial magnetic field is shown to create a window of stability in the space of the flow parameters, where th Rayleigh-Taylor modes are fully suppressed by the magnetic shear, and the bulk convective ones - to a considerable extent. The axial magnetic field required to stabilize the implosion of a liner is estimated as B z0 =(10-30 kG)I(MA)/R 0 (cm), where I is the average current, R 0 - the initial radius of the liner

Statistical dynamics of transient processes in a gas discharge plasma

International Nuclear Information System (INIS)

Smirnov, G.I.; Telegin, G.G.

1991-01-01

The properties of a gas discharge plasma to a great extent depend on random processes whose study has recently become particularly important. The present work is concerned with analyzing the statistical phenomena that occur during the prebreakdown stage in a gas discharge. Unlike other studies of breakdown in the discharge gap, in which secondary electron effects and photon processes at the electrodes must be considered, here the authors treat the case of an electrodeless rf discharge or a laser photoresonant plasma. The analysis is based on the balance between the rates of electron generation and recombination in the plasma. The fluctuation kinetics for ionization of atoms in the hot plasma may also play an important role when the electron temperature changes abruptly, as occurs during adiabatic pinching of the plasma or during electron cyclotron heating

Modelling of a Nitrogen X-ray Laser pumped by Capillary Discharge

Czech Academy of Sciences Publication Activity Database

Vrba, Pavel; Vrbová, M.; Bobrova, N. A.; Sasorov, P. V.

2005-01-01

Roč. 3, č. 4 (2005), s. 564-580 ISSN 1644-3608 R&D Projects: GA MŠk(CZ) 1P04LA235 Institutional research plan: CEZ:AV0Z20430508 Keywords : MHD simulations * Z-pinch * Ion kinetics * Recombination Pumping * X-Ray laser Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 0.524, year: 2005

Construction of a high beta plasma source

International Nuclear Information System (INIS)

Naraghi, M.; Torabi-Fard, A.

1976-02-01

A high beta plasma source has been designed and constructed. This source will serve as a means of developing and exercising different diagnostic techniques as required for ALVAND I, linear theta pinch experiment. Also, it will serve to acquaint the technicians with some of the techniques and safety rules of high voltage and capacitor discharge experiments. The operating parameters of the theta pinch and Z-pinch preionization is presented and the program of diagnostic measurements on the high beta plasma source is discussed

Magnetohydrodynamic simulation of solid-deuterium-initiated Z-pinch experiments

International Nuclear Information System (INIS)

Sheehey, P.T.

1994-02-01

Solid-deuterium-initiated Z-pinch experiments are numerically simulated using a two-dimensional resistive magnetohydrodynamic model, which includes many important experimental details, such as ''cold-start'' initial conditions, thermal conduction, radiative energy loss, actual discharge current vs. time, and grids of sufficient size and resolution to allow realistic development of the plasma. The alternating-direction-implicit numerical technique used meets the substantial demands presented by such a computational task. Simulations of fiber-initiated experiments show that when the fiber becomes fully ionized rapidly developing m=0 instabilities, which originated in the coronal plasma generated from the ablating fiber, drive intense non-uniform heating and rapid expansion of the plasma column. The possibility that inclusion of additional physical effects would improve stability is explored. Finite-Larmor-radius-ordered Hall and diamagnetic pressure terms in the magnetic field evolution equation, corresponding energy equation terms, and separate ion and electron energy equations are included; these do not change the basic results. Model diagnostics, such as shadowgrams and interferograms, generated from simulation results, are in good agreement with experiment. Two alternative experimental approaches are explored: high-current magnetic implosion of hollow cylindrical deuterium shells, and ''plasma-on-wire'' (POW) implosion of low-density plasma onto a central deuterium fiber. By minimizing instability problems, these techniques may allow attainment of higher temperatures and densities than possible with bare fiber-initiated Z-pinches. Conditions for significant D-D or D-T fusion neutron production may be realizable with these implosion-based approaches

Performance improvement of centrifugal compressor stage with pinched geometry or vaned diffuser

Energy Technology Data Exchange (ETDEWEB)

Jaatinen, A.

2009-07-01

Centrifugal compressors are widely used for example in refrigeration processes, the oil and gas industry, superchargers, and waste water treatment. In this work, five different vaneless diffusers and six different vaned diffusers are investigated numerically. The vaneless diffusers vary only by their diffuser width, so that four of the geometries have pinch implemented to them. Pinch means a decrease in the diffuser width. Four of the vaned diffusers have the same vane turning angle and a different number of vanes, and two have different vane turning angles. The flow solver used to solve the flow fields is Finfo, which is a Navier-Stokes solver. All the cases are modeled Chien's k-epsilon turbulence model. All five vaneless diffusers and three vaned diffusers are investigated also experimentally. For each construction, the compressor operating map is measured according to relevant standards. In addition to this, the flow fields before and after the diffuser are measured with static and total pressure, flow angle and total temperature measurements k-omega SST turbulence model. The simulation results indicate that it is possible to improve the efficiency with the pinch, and according to the numerical results, the two best geometries are the ones with most pinch at the shroud. These geometries have approximately 4 percentage points higher effciency than the unpinched vaneless diffusers. The hub pinch does not seem to have any major benefits. In general, the pinches make the flow fields before and after the diffuser more uniform. The pinch also seems to improve the impeller effciency. This is down to two reasons. The major reason is that the pinch decreases the size of slow flow and possible backflow region located near the shroud after the impeller. Secondly, the pinches decrease the flow velocity in the tip clearance, leading to a smaller tip leakage flow and therefore slightly better impeller efficiency. Also some of the vaned diffusers improve the efficiency

Acoustic bubble enhanced pinched flow fractionation for microparticle separation

International Nuclear Information System (INIS)

Zhou, Ran; Wang, Cheng

2015-01-01

Pinched flow fractionation is a simple method for separating micron-sized particles by size, but has certain intrinsic limitations, e.g. requirement of a pinched segment similar to particle size and limited separation distance. In this paper, we developed an acoustic bubble enhanced pinched flow fractionation (PFF) method for microparticle separation. The proposed technique utilized microbubble streaming flows to overcome the limitations of conventional PFF. Our device has demonstrated separation of different sized microparticles (diameters 10 and 2 μm) with a larger pinched segment (60 μm) and at different buffer/particle solution flow rate ratios (5–25). The separation distances between particles are larger (as much as twice as large) than those achieved with conventional PFF. In addition, the separation position and distance can be adjusted by changing the driving voltage. The robust performance is due to the unique features of the flow field inside the pinched segment. We investigated several factors, including flow rate ratio, total flow rate and driving voltage, that affect the separation performance. (paper)

Deuterium z-pinch as a powerful source of multi-MeV ions and neutrons for advanced applications

Czech Academy of Sciences Publication Activity Database

Klir, D.; Shishlov, A. V.; Kokshenev, V. A.; Kubes, P.; Labetsky, A. Yu.; Rezac, K.; Cherdizov, R. K.; Cikhardt, J.; Cikhardtová, B.; Dudkin, G. N.; Fursov, F. I.; Garapatsky, A. A.; Kovalchuk, B. M.; Krása, Josef; Kravarik, J.; Kurmaev, N. E.; Orčíková, Hana; Padalko, V. N.; Ratakhin, N. A.; Sila, O.; Turek, Karel; Varlachev, V. A.; Velyhan, Andriy; Wagner, Richard

2016-01-01

Roč. 23, č. 3 (2016), 1-10, č. článku 032702. ISSN 1070-664X R&D Projects: GA ČR GA16-07036S; GA MŠk(CZ) LD14089; GA MŠk(CZ) LG13029 Grant - others:GA MŠk(CZ) LH13283 Institutional support: RVO:68378271 ; RVO:61389005 Keywords : neutrons * Z-pinch * ion sources * isotopes * protons Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.115, year: 2016

Development of a Z-pinch-driven ICF hohlraum concept on Z

International Nuclear Information System (INIS)

Cuneo, M.E.; Porter, J.L. Jr.; Vesey, R.A.

1999-01-01

Recent development of high power z-pinches (> 150 MW) on the Z driver has permitted the study of high-temperature, radiation-driven hohlraums. Three complementary, Z-pinch source-hohlraum-ICF capsule configurations are being developed to harness the x-ray output of these Z-pinch's. These are the dynamic-hohlraum, static-wall hohlraum, and Z-pinch-driven hohlraum concepts. Each has different potential strengths and concerns. In this paper, the authors report on the first experiments with the Z-pinch-driven hohlraum (ZPDH) concept. A high-yield ICF capsule design for this concept appears feasible, when driven by z-pinches from a 60 MA-class driver. Initial experiments characterize the behavior of the spoke array on Z-pinch performance and x-ray transmission, and the uniformity of radiation flux incident on a foam capsule in the secondary, for a single-sided drive. Measurements of x-ray wall re-emission power and spectrum, radiation temperatures, spoke-plasma location, and drive uniformity will be presented and compared with 0-D energetics, 2-D Lasnex rad-hydro, and 3-D radiosity calculations of energy transport and drive uniformity

Development of a Z-pinch-driven ICF hohlraum concept on Z

Energy Technology Data Exchange (ETDEWEB)

Cuneo, M E; Porter, Jr, J L; Vesey, R A [and others

1999-07-01

Recent development of high power z-pinches (> 150 MW) on the Z driver has permitted the study of high-temperature, radiation-driven hohlraums. Three complementary, Z-pinch source-hohlraum-ICF capsule configurations are being developed to harness the x-ray output of these Z-pinch's. These are the dynamic-hohlraum, static-wall hohlraum, and Z-pinch-driven hohlraum concepts. Each has different potential strengths and concerns. In this paper, the authors report on the first experiments with the Z-pinch-driven hohlraum (ZPDH) concept. A high-yield ICF capsule design for this concept appears feasible, when driven by z-pinches from a 60 MA-class driver. Initial experiments characterize the behavior of the spoke array on Z-pinch performance and x-ray transmission, and the uniformity of radiation flux incident on a foam capsule in the secondary, for a single-sided drive. Measurements of x-ray wall re-emission power and spectrum, radiation temperatures, spoke-plasma location, and drive uniformity will be presented and compared with 0-D energetics, 2-D Lasnex rad-hydro, and 3-D radiosity calculations of energy transport and drive uniformity.

A solvable self-similar model of the sausage instability in a resistive Z pinch

International Nuclear Information System (INIS)

Lampe, M.

1991-01-01

A solvable model is developed for the linearized sausage mode within the context of resistive magnetohydrodynamics. The model is based on the assumption that the fluid motion of the plasma is self-similar, as well as several assumptions pertinent to the limit of wavelength long compared to the pinch radius. The perturbations to the magnetic field are not assumed to be self-similar, but rather are calculated. Effects arising from time dependences of the z-independent perturbed state, e.g., current rising as t α , Ohmic heating, and time variation of the pinch radius, are included in the analysis. The formalism appears to provide a good representation of ''global'' modes that involve coherent sausage distortion of the entire cross section of the pinch, but excludes modes that are localized radially, and higher radial eigenmodes. For this and other reasons, it is expected that the model underestimates the maximum instability growth rates, but is reasonable for global sausage modes. The net effect of resistivity and time variation of the unperturbed state is to decrease the growth rate if α approx-lt 1, but never by more than a factor of about 2. The effect is to increase the growth rate if α approx-gt 1

Impact of PINCH expression on survival in colorectal cancer patients

International Nuclear Information System (INIS)

Lööf, Jasmine; Rosell, Johan; Bratthäll, Charlotte; Doré, Siv; Starkhammar, Hans; Zhang, Hong; Sun, Xiao-Feng

2011-01-01

The adaptor protein PINCH is overexpressed in the stroma of several types of cancer, and is an independent prognostic marker in colorectal cancer. In this study we further investigate the relationship of PINCH and survival regarding the response to chemotherapy in colorectal cancer. Paraffin-embedded tissue sections from 251 primary adenocarcinomas, 149 samples of adjacent normal mucosa, 57 samples of distant normal mucosa and 75 lymph node metastases were used for immunohistochemical staining. Stromal staining for PINCH increased from normal mucosa to primary tumour to metastasis. Strong staining in adjacent normal mucosa was related to worse survival independently of sex, age, tumour location, differentiation and stage (p = 0.044, HR, 1.60, 95% CI, 1.01-2.52). PINCH staining at the invasive margin tended to be related to survival (p = 0.051). In poorly differentiated tumours PINCH staining at the invasive margin was related to survival independently of sex, age and stage (p = 0.013, HR, 1.90, 95% CI, 1.14-3.16), while in better differentiated tumours it was not. In patients with weak staining, adjuvant chemotherapy was related to survival (p = 0.010, 0.013 and 0.013 in entire tumour area, invasive margin and inner tumour area, respectively), but not in patients with strong staining. However, in the multivariate analysis no such relationship was seen. PINCH staining in normal adjacent mucosa was related to survival. Further, PINCH staining at the tumour invasive margin was related to survival in poorly differentiated tumours but not in better differentiated tumours, indicating that the impact of PINCH on prognosis was dependent on differentiation status

Influence of pinches on magnetic reconnection in turbulent space plasmas

Science.gov (United States)

Olshevsky, Vyacheslav; Lapenta, Giovanni; Markidis, Stefano; Divin, Andrey

A generally accepted scenario of magnetic reconnection in space plasmas is the breakage of magnetic field lines in X-points. In laboratory, reconnection is widely studied in pinches, current channels embedded into twisted magnetic fields. No model of magnetic reconnection in space plasmas considers both null-points and pinches as peers. We have performed a particle-in-cell simulation of magnetic reconnection in a three-dimensional configuration where null-points are present nitially, and Z-pinches are formed during the simulation. The X-points are relatively stable, and no substantial energy dissipation is associated with them. On contrary, turbulent magnetic reconnection in the pinches causes the magnetic energy to decay at a rate of approximately 1.5 percent per ion gyro period. Current channels and twisted magnetic fields are ubiquitous in turbulent space plasmas, so pinches can be responsible for the observed high magnetic reconnection rates.

Experimental studies of the argon-puff Z-pinch implosion process

International Nuclear Information System (INIS)

Huang Xianbin; Yang Libing; Gu Yuanchao; Deng Jianjun; Zhou Rongguo; Zou Jie; Zhou Shaotong; Zhang Siqun; Chen Guanghua; Chang Lihua; Li Fengping; Ouyang Kai; Li Jun; Yang Liang; Wang Xiong; Zhang Zhaohui

2006-01-01

A preliminary experiment for studying the argon-puff Z-pinch implosion process has been performed on the Yang accelerator. The ten-frame nanosecond temporal and spatial gated camera, visible high-speed scanning camera, differential laser interferometer, X-ray time integration pinhole camera and X-ray power system have been used to investigated the evolution of the argon-puff Z-pinch. Some typical results of argon-puff Z-pinch during implosion and pinch phase, including the 'zipper' effect, necking phenomenon, sausage instability, temperature changes and the effect of load current rise time, are given and analyzed as examples, and some relevant conclusions are drawn. (authors)

X-Pinch And Its Applications In X-ray Radiograph

International Nuclear Information System (INIS)

Zou Xiaobing; Wang Xinxin; Liu Rui; Zhao Tong; Zeng Naigong; Zhao Yongchao; Du Yanqiang

2009-01-01

An X-pinch device and the related diagnostics of x-ray emission from X-pinch were briefly described. The time-resolved x-ray measurements with photoconducting diodes show that the x-ray pulse usually consists of two subnanosecond peaks with a time interval of about 0.5 ns. Being consistent with these two peaks of the x-ray pulse, two point x-ray sources of size ranging from 100 μm to 5 μm and depending on cut-off x-ray photon energy were usually observed on the pinhole pictures. The x-pinch was used as x-ray source for backlighting of the electrical explosion of single wire and the evolution of X-pinch, and for phase-contrast imaging of soft biological objects such as a small shrimp and a mosquito.

Development of sausage-type instability in a Z-pinch plasma column

International Nuclear Information System (INIS)

Vikhrev, V.V.; Ivanov, V.V.; Rozanova, G.A.

1993-01-01

The development of sausage-type instabilities in an initially homogeneous Z-pinch plasma column has been investigated by means of numerical modelling. It is shown that in the presence of short-wave perturbations of a Z-pinch boundary and a rarefied plasma surrounding the pinch, cavities filled with a rarefied plasma and with a magnetic field are formed in the plasma column. As a result of this cavity growth, small columns of dense plasma form on the axis in the Z-pinch which have a temperature substantially higher than the average plasma temperature in the plasma column. When deuterium is present in the pinch, these dense high temperature bunches can become a source of intensive neutron radiation. (author). 24 refs, 7 figs

ANALYSIS OF POWER GRIP AND PINCH GRIP AMONG HEALTH CARE PROFESSIONALS

Directory of Open Access Journals (Sweden)

Zakariya M P

2016-02-01

Full Text Available Background: Grip and pinch strength are commonly employed indices of strength used in hand evaluations. Pinch grip and power grip strengths are used as indices of strength in hand therapy assessments. For all professions grip strength is an important criterion to be successful in their profession. Such phenomena may be explained by differences in nature of work, working environment, and objects workers handle. Method: 200 healthy subjects, satisfying the selection criteria were included and assessed with standardized procedure for power grip and pinch grip (lateral pinch, pad-pad, and tip-tip strength. They were divided in four groups, 50 group each according to profession i.e. medical surgeons, dentist, physiotherapists and nurses. Results: The mean power grip strength shows highly significant difference between medical vs. dental (p>0.01 and medical vs. physiotherapy group (p> 0.05 .The mean lateral pinch strength shows there is highly significant difference (p< 0.001 between dental vs. nursing profession and dental vs. physiotherapy group. No significant difference among other groups. The mean pad-pad pinch strength shows there is significant difference between dental vs. nursing (p< 0.05 and dental vs physiotherapy group (p< 0.05. The mean Tip-Tip pinch strength shows there is significant difference between dental vs nursing profession(p< 0.05 and dental vs. physiotherapy(p< 0.05. No significant different among other groups. Conclusion: Surgeons have highest power grip strength followed by Nursing, Physiotherapy and Dental professionals. Dentists have the maximum pinch strength in all three positions, followed by Surgeons, Nurses and Physiotherapists. Surgeons have maximum pinch strength next to Dentists.

Spatially resolved single crystal x-ray spectropolarimetry of wire array z-pinch plasmas.

Science.gov (United States)

Wallace, M S; Haque, S; Neill, P; Pereira, N R; Presura, R

2018-01-01

A recently developed single-crystal x-ray spectropolarimeter has been used to record paired sets of polarization-dependent and axially resolved x-ray spectra emitted by wire array z-pinches. In this measurement, two internal planes inside a suitable crystal diffract the x-rays into two perpendicular directions that are normal to each other, thereby separating incident x-rays into their linearly polarized components. This paper gives considerations for fielding the instrument on extended sources. Results from extended sources are difficult to interpret because generally the incident x-rays are not separated properly by the crystal. This difficulty is mitigated by using a series of collimating slits to select incident x-rays that propagate in a plane of symmetry between the polarization-splitting planes. The resulting instrument and some of the spatially resolved polarized x-ray spectra recorded for a 1-MA aluminum wire array z-pinch at the Nevada Terawatt Facility at the University of Nevada, Reno will be presented.

3-dimensional simulation of dynamo effect of reversed field pinch

International Nuclear Information System (INIS)

Koide, Shinji.

1990-09-01

A non-linear numerical simulation of the dynamo effect of a reversed field pinch (RFP) with finite beta is presented. It is shown that the m=-1, n=(9,10,11,....,19) modes cause the dynamo effect and sustain the field reversed configuration. The role of the m=0 modes on the dynamo effect is carefully examined. Our simulation shows that the magnetic field fluctuation level scales as S -0.2 or S -0.3 in the range of 10 3 5 , while Nebel, Caramana and Schnack obtained the fluctuation level is independent of S for a pressureless RFP plasma. (author)

Effect of transcranial magnetic stimulation on force of finger pinch

Science.gov (United States)

Odagaki, Masato; Fukuda, Hiroshi; Hiwaki, Osamu

2009-04-01

Transcranial magnetic stimulation (TMS) is used to explore many aspects of brain function, and to treat neurological disorders. Cortical motor neuronal activation by TMS over the primary motor cortex (M1) produces efferent signals that pass through the corticospinal tracts. Motor-evoked potentials (MEPs) are observed in muscles innervated by the stimulated motor cortex. TMS can cause a silent period (SP) following MEP in voluntary electromyography (EMG). The present study examined the effects of TMS eliciting MEP and SP on the force of pinching using two fingers. Subjects pinched a wooden block with the thumb and index finger. TMS was applied to M1 during the pinch task. EMG of first dorsal interosseous muscles and pinch forces were measured. Force output increased after the TMS, and then oscillated. The results indicated that the motor control system to keep isotonic forces of the muscles participated in the finger pinch was disrupted by the TMS.

Scaling of X pinches from 1 MA to 6 MA

International Nuclear Information System (INIS)

Bland, Simon Nicholas; McBride, Ryan D.; Wenger, David Franklin; Sinars, Daniel Brian; Chittenden, Jeremy Paul; Pikuz, Sergei A.; Harding, Eric; Jennings, Christopher A.; Ampleford, David J.; Yu, Edmund P.; Cuneo, Michael Edward; Shelkovenko, Tatiana A.; Hansen, Stephanie B.

2010-01-01

This final report for Project 117863 summarizes progress made toward understanding how X-pinch load designs scale to high currents. The X-pinch load geometry was conceived in 1982 as a method to study the formation and properties of bright x-ray spots in z-pinch plasmas. X-pinch plasmas driven by 0.2 MA currents were found to have source sizes of 1 micron, temperatures >1 keV, lifetimes of 10-100 ps, and densities >0.1 times solid density. These conditions are believed to result from the direct magnetic compression of matter. Physical models that capture the behavior of 0.2 MA X pinches predict more extreme parameters at currents >1 MA. This project developed load designs for up to 6 MA on the SATURN facility and attempted to measure the resulting plasma parameters. Source sizes of 5-8 microns were observed in some cases along with evidence for high temperatures (several keV) and short time durations (<500 ps).

Experimental study of the neck formation in an X pinch

International Nuclear Information System (INIS)

Artyomov, A P; Chaikovsky, S A; Fedunin, A V; Labetskaya, N A; Rousskikh, A G; Zhigalin, A S; Oreshkin, V I

2014-01-01

X-pinch experiments have been performed on a compact 250 kA, 180 ns pulsed power generator specially designed for this purpose at the Institute of High Current Electronics (Tomsk, Russia). The X pinches were composed of two molybdenum wires of diameter 25 μm making an angle of 36° with the z-axis. The X-pinch dynamics was recorded with a 3 ns exposure time using an HSFC Pro four-frame camera. Axial plasma jets propagating toward both the anode and the cathode were observed. The jets became noticeable within 10 ns after the onset of current flow, which approximately corresponded to the time at which the electrical explosion of the X-pinch wires occurred. The velocity of the anode-directed jet reached 10 7 cm/s, which was about 1.5 times the velocity of the cathode-directed jet. These high jet velocities are inconsistent with the plasma temperature resulting from the wire explosion. Hence, these jets seem to develop due to implosion of the light plasma layer stripped by magnetic forces from the wire surface, and the increase in their velocities is perhaps due to cumulative effects taking place at the X-pinch axis. The X-pinch neck formed as a rule above the initial wire cross point (closer to the anode). In this region, the plasma diameter gradually increased with time and then drastically decreased 10-15 ns prior to the x-ray pulse. Immediately before the x-ray pulse, in the (250-300 μm long) plasma neck, a lower scale constriction developed, forming a h ot spot . It has been confirmed that the anode-directed plasma jet could take some part of the X-pinch wire current because of the evident jet pinching in the anode region. This process seems to determine the neck length

WATER PINCH TECHNOLOGY APPLICATION TO MINIMIZE SULPHUROUS WASTEWATER IN AN OIL REFINERY

Directory of Open Access Journals (Sweden)

Gabriel Orlando Lobelles Sardiñas

2017-01-01

Full Text Available In oil refining industries there is a high water consumption, which influences the high production costs and impacts the environment due to the discharge of their wastes. It is known that there are no technological conditions for the reuse of industrial water at the oil refineries, based on hydroskimming processes. The objective of this study is to implement the process integration methodology, Water Pinch, to a sour water stripper unit, as a unitary process of an oil refinery, to minimize the amount of sulphurous waste water and reduce contamination of the bay that receives these wastes. The technology is applied to evaluate the volume of sulphurous wastewater generated in the Cienfuegos oil refinery. This technology allows identifying opportunities for recovery and reuse of water, based on concentration ranges of contaminants. To achieve this purpose, a sour water stripper tower was assessed with the help of Water Pinch software, which provided an optimized distribution network, as a proposed technological improvement. This facilitated to recover and reuse 667 757, 28 m3 of water per year, and 1 035 023, 78 CUC were saved, at the same time the amount of polluting effluents decreased in approximately 2 % of non-reusable treated water.

Investigation of layered Z-pinches on ANGARA-5-1

Energy Technology Data Exchange (ETDEWEB)

Branitskij, A V; Grabovskij, E V; Zakharov, S V; Zurin, M V; Nedoseev, S L; Olejnik, G M; Smirnov, V P; Frolov, I N [Troitsk Inst. of Innovative and Fusion Research (Russian Federation)

1997-12-31

Experimental results of layered Z-pinch investigations on Angara-5-1 are presented. The level of current was 3-4 MA through a load with a 70-90 ns rise time. The initial-to-final radius ratio increased from 10-15 for a conventional single pinch, up to 30-50 for the double layered design. A power flux of about 8-12 TW/cm{sup 2} was achieved with front rise time about 3 ns. The final pinch diameter was down to 0.5-1 mm. (author). 4 figs., 1 ref.

A Reactor Development Scenario for the FuZE Sheared-Flow Stabilized Z-pinch

Science.gov (United States)

McLean, Harry S.; Higginson, D. P.; Schmidt, A.; Tummel, K. K.; Shumlak, U.; Nelson, B. A.; Claveau, E. L.; Forbes, E. G.; Golingo, R. P.; Stepanov, A. D.; Weber, T. R.; Zhang, Y.

2017-10-01

We present a conceptual design, scaling calculations, and development path for a pulsed fusion reactor based on a flow-stabilized Z-pinch. Experiments performed on the ZaP and ZaP-HD devices have largely demonstrated the basic physics of sheared-flow stabilization at pinch currents up to 100 kA. Initial experiments on the FuZE device, a high-power upgrade of ZaP, have achieved 20 usec of stability at pinch current 100-200 kA and pinch diameter few mm for a pinch length of 50 cm. Scaling calculations based on a quasi-steady-state power balance show that extending stable duration to 100 usec at a pinch current of 1.5 MA and pinch length of 50 cm, results in a reactor plant Q 5. Future performance milestones are proposed for pinch currents of: 300 kA, where Te and Ti are calculated to exceed 1-2 keV; 700 kA, where DT fusion power would be expected to exceed pinch input power; and 1 MA, where fusion energy per pulse exceeds input energy per pulse. This work funded by USDOE ARPA-E and performed under the auspices of Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-734770.

Resistive wall instabilities and tearing mode dynamics in the EXTRAP T2R thin shell reversed-field pinch

Science.gov (United States)

Malmberg, J.-A.; Brunsell, P. R.

2002-01-01

Observations of resistive wall instabilities and tearing mode dynamics in the EXTRAP T2R thin shell (τw=6 ms) reversed field pinch are described. A nonresonant mode (m=1,n=-10) with the same handedness as the internal field grows nearly exponentially with an average growth time of about 2.6 ms (less than 1/2 of the shell time) consistent with linear stability theory. The externally nonresonant unstable modes (m=1,n>0), predicted by linear stability theory, are observed to have only low amplitudes (in the normal low-Θ operation mode of the device). The radial field of the dominant internally resonant tearing modes (m=1,n=-15 to n=-12) remain low due to spontaneous fast mode rotation, corresponding to angular phase velocities up to 280 krad/s. Phase aligned mode structures are observed to rotate toroidally with an average angular velocity of 40 krad/s, in the opposite direction of the plasma current. Toward the end of the discharge, the radial field of the internally resonant modes grows as the modes slow down and become wall-locked, in agreement with nonlinear computations. Fast rotation of the internally resonant modes has been observed only recently and is attributed to a change of the front-end system (vacuum vessel, shell, and TF coil) of the device.

X-ray sources by Z-pinch for inertial confinement fusion

International Nuclear Information System (INIS)

Akiyama, Hidenori; Katsuki, Sunao; Lisitsyn, Igor

1999-01-01

Inertial confinement nuclear fusion driven by X-ray from Z-pinch plasmas has been developed. Recently, extremely high X-ray power (290 TW) and energy (1.8 MJ) were produced in fast Z-pinch implosions on the Z accelerator (Sandia National Laboratories). Wire arrays are used to produce the initial plasma. The X-ray from Z-pinch plasmas produced by pulsed power has great potential as a driver of inertial confinement nuclear fusion. (author)

Engineering prototypes for theta-pinch devices

International Nuclear Information System (INIS)

Hansborough, L.D.; Hammer, C.F.; Hanks, K.W.; McDonald, T.E.; Nunnally, W.C.

1975-01-01

Past, present, and future engineering prototypes for theta-pinch plasma-physics devices at Los Alamos Scientific Laboratory are discussed. Engineering prototypes are designed to test and evaluate all components under system conditions expected on actual plasma-physics experimental devices. The importance of engineering prototype development increases as the size and complexity of the plasma-physics device increases. Past experiences with the Scyllac prototype and the Staged Theta-Pinch prototype are discussed and evaluated. The design of the proposed Staged Scyllac prototype and the Large Staged Scyllac implosion prototype assembly are discussed

Self-Consolidation Mechanism Of Porous Ti-6Al-4V Implant Prototypes Produced By Electro-Discharge-Sintering Of Spherical Ti-6Al-4V Powders

Directory of Open Access Journals (Sweden)

Lee W.H.

2015-06-01

Full Text Available Electro-Discharge-Sintering (EDS was employed to fabricate Ti-6Al-4V porous implant prototypes from atomized powders (100 – 150 μm, that were subjected to discharges of 0.75 to 2.0 kJ/0.7g-powder from 150, 300, and 450 μF capacitors. Both fully porous and porous-surfaced Ti-6Al-4V compacts with various solid core sizes were self-consolidated in less than 86 – 155 μsec. It is known that EDS can simultaneously produce the pinch pressure to squeeze and deform powder particles and the heat to weld them together. The formation of a solid core in these prototypes depends on the amounts of both the pinch pressure and heat generated during a discharge. The size of the solid core and the thickness of the porous layer can be successfully controlled by manipulating the discharge conditions such as input energy and capacitance.

SLAC linear collider conceptual design report

Energy Technology Data Exchange (ETDEWEB)

1980-06-01

The linear collider system is described in detail, including the transport system, the collider lattice, final focusing system, positron production, beam damping and compression, high current electron source, instrumentation and control, and the beam luminosity. The experimental facilities and the experimental uses are discussed along with the construction schedule and estimated costs. Appendices include a discussion of space charge effects in the linear accelerator, emittance growth in the collider, the final focus system, beam-beam instabilities and pinch effects, and detector backgrounds. (GHT)

SLAC linear collider conceptual design report

International Nuclear Information System (INIS)

1980-06-01

The linear collider system is described in detail, including the transport system, the collider lattice, final focusing system, positron production, beam damping and compression, high current electron source, instrumentation and control, and the beam luminosity. The experimental facilities and the experimental uses are discussed along with the construction schedule and estimated costs. Appendices include a discussion of space charge effects in the linear accelerator, emittance growth in the collider, the final focus system, beam-beam instabilities and pinch effects, and detector backgrounds

Study of flow and loss processes at the ends of a linear theta pinch. Progress report, June 1, 1979-September 30, 1980

International Nuclear Information System (INIS)

York, T.M.; Klevans, E.H.

1980-05-01

Experimental and analytical studies of particle and energy loss at the ends of a linear theta pinch have been carried out. A study of transients occurring in the formation of reversed trapped fields within the coil, and of transients in the end region of a 25 cm long device was completed. A 1-D code has proven to be highly accurate in describing loss events and defining transport mechanisms in different experiments and is described here. A study of loss along field lines in a 50 cm long device has generated new information on loss velocity, axial and radial temperature gradients, and has established an initial effort in understanding thermal loss to the walls. Rotation and parallel trapped fields have been added to the existing 0-D code. A new technique crowbar switch and magnetic field prediction code have been developed. Direct measurment of electron velocity with Thomson scattering was accomplished experimentally. A Nd-glass laser system, frequency doubled, is being developed for low density diagnostics. Theoretical results that accurately predict confinement in FRX devices are described

The ZaP Flow Z-Pinch Project - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Shumlak, Uri [Univ. of Washington, Seattle, WA (United States); Nelson, Brian A. [Univ. of Washington, Seattle, WA (United States)

2013-12-31

The ZaP Flow Z-Pinch Project is a project to extend the performance of the flow Z-pinch experiment at the University of Washington to investigate and isolate the relevant physics of the stabilizing effect of plasma flow. Experimental plasmas have exhibited an enhanced stability under certain operating parameters which generate a flow state (axial flows in Z-pinches and VH mode in tokamaks). Flow has also been suggested as the stabilizing mechanism in astrophysical jets.

Computational modeling of z-pinch-driven hohlraum experiments on Z

International Nuclear Information System (INIS)

Vesey, R.A.; Porter, J.L. Jr.; Cuneo, M.E.

1999-01-01

The high-yield inertial confinement fusion concept based on a double-ended z-pinch driven hohlraum tolerates the degree of spatial inhomogeneity present in z-pinch plasma radiation sources by utilizing a relatively large hohlraum wall surface to provide spatial smoothing of the radiation delivered to the fusion capsule. The z-pinch radiation sources are separated from the capsule by radial spoke arrays. Key physics issues for this concept are the behavior of the spoke array (effect on the z-pinch performance, x-ray transmission) and the uniformity of the radiation flux incident on the surface of the capsule. Experiments are underway on the Z accelerator at Sandia National laboratories to gain understanding of these issues in a single-sided drive geometry. These experiments seek to measure the radiation coupling among the z-pinch, source hohlraum, and secondary hohlraum, as well as the uniformity of the radiation flux striking a foam witness ball diagnostic positioned in the secondary hohlraum. This paper will present the results of computational modeling of various aspects of these experiments

A note on the relationship between the emittance, the beta function and the energy in a linear collider

International Nuclear Information System (INIS)

Rees, J.

1986-11-01

Scaling laws for linear colliders are considered for the case of laterally round Gaussian beams and for the case that mutual pinching of the beams can be ignored. Based on these assumptions, the relationship is found between the interaction area, beta function, beam emittance, and energy for a linear collider in order to show the need for substantial improvements in the feasible values of accelerator parameters to reach a center of mass energy of 0.7 TeV. Pinch is then taken into account

The pinch of cold ions from recycling in the tokamak edge pedestal

International Nuclear Information System (INIS)

Wan Weigang; Parker, Scott E.; Chen Yang; Park, Gun-Young; Chang, Choong-Seock; Stotler, Daren

2011-01-01

We apply the ''natural fueling mechanism'' [W. Wan, S. E. Parker, Y. Chen, and F. W. Perkins, Phys. Plasmas 17, 040701 (2010)] to the edge pedestal. The natural fueling mechanism is where cold ions naturally pinch radially inward for a heat-flux dominated plasma. It is shown from neoclassical-neutral transport coupled simulations that the recycling neutrals and the associated source ions are colder than the main ions in the edge pedestal. These recycling source ions will pinch radially inward due to microturbulence. Gyrokinetic turbulence simulations indicate that near the top of the pedestal, the pinch velocity of the recycling source ions is much higher than the main ion outgoing flow velocity. The turbulent pinch of the recycling source ions may play a role in the edge pedestal transport and dynamics. The cold ion temperature significantly enhances the pinch velocity of the recycling source ions near to the pedestal top. Neoclassical calculations show a cold ion pinch in the pedestal as well.

Experimental Study of Current Discharge Behavior and Hard X-ray Anisotropy by APF Plasma Focus Device

Science.gov (United States)

Habibi, M.; Amrollahi, R.; Attaran, M.

2009-03-01

Amirkabir (APF) is a new Mather-type plasma focus device (16 kV, 36 μf, and 115 nH). In this work we present some experimental results as variation of discharge current signal respect to applied voltage at the optimum pressure, focusing time of plasma versus gas pressure, and variations of current discharge with different insulator sleeve dimensions. As we prospected optimum pressure tending to increase as we tried to higher voltage levels. The time taken by the current sheath to lift-off the insulator surface and therefore quality of pinched plasma depends on the length of the insulator sleeve. The results show that the insulator diameter can influence on pinch quality. Behavior of hard X-ray (HXR) signals with the pressure and also anisotropy of HXR investigated by the use of two scintillation detectors. The distribution of HXR intensity shows a large anisotropy with a maximum intensity between 22.5° and 45° and also between -22.5° and -67.5°.

Particle orbits and non-ideal MHD stability of Z-pinches

International Nuclear Information System (INIS)

Faghihi, M.

1987-01-01

Particle orbits in a linear EXTRAP vacuum magnetic field configuration are computed. The results indicate that, with an applied electric field along the axis, the particles starting near the magnetic stagnation line would gain substantial energy in the 'free fall', and are the most efficient ones to participate in the ionization process. The acquired energy depends on the electric field strength; the required value of the field is determined. The influence of the pressure anisotropy on the small wavelength internal kink (m=1) mode instability in a Z-pinch, using a generalization of Freidbergs perpendicular MHD model, is investigated. It is found that the stability criterion can not be fulfilled without violation of the fire hose stability condition. This investigation is also performed using the double-adiabatic theory. A finite Larmor radius treatment of the small wavelength kink instabilities for a Z-pinch geometry is presented. It is shown that, when the gyroviscosity is included in the perpendicular MHD model, exponentially growing Alfven waves are predicted even in a homogeneous static equilibrium with isotropic plasma pressure. The Hall effect in the incompressible Hall fluid model is considered. It is found that the Hall parameter reduces the growth rates of the kink modes, but it does not yield complete stabilization (author)

Particle orbits and non-ideal MHD stability of Z-pinches

Energy Technology Data Exchange (ETDEWEB)

Faghihi, M.

1987-01-01

Particle orbits in a linear EXTRAP vacuum magnetic field configuration are computed. The results indicate that, with an applied electric field along the axis, the particles starting near the magnetic stagnation line would gain substantial energy in the 'free fall', and are the most efficient ones to participate in the ionization process. The acquired energy depends on the electric field strength; the required value of the field is determined. The influence of the pressure anisotropy on the small wavelength internal kink (m=1) mode instability in a Z-pinch, using a generalization of Freidbergs perpendicular MHD model, is investigated. It is found that the stability criterion can not be fulfilled without violation of the fire hose stability condition. This investigation is also performed using the double-adiabatic theory. A finite Larmor radius treatment of the small wavelength kink instabilities for a Z-pinch geometry is presented. It is shown that, when the gyroviscosity is included in the perpendicular MHD model, exponentially growing Alfven waves are predicted even in a homogeneous static equilibrium with isotropic plasma pressure. The Hall effect in the incompressible Hall fluid model is considered. It is found that the Hall parameter reduces the growth rates of the kink modes, but it does not yield complete stabilization

Diffusion-driven steady states of the Z-pinch

International Nuclear Information System (INIS)

Lehnert, B.

1988-01-01

Steady states of a Z-pinch where no electric field is imposed along the pinch axis by external means are investigated. In this case, diffusion-driven states become possible when imposed volume sources of particles and heat drive a radial diffusion velocity that, in its turn, generates the electric plasma current. The particle sources can be from pellet injection or a neutral gas blanket, and the heat sources provided by thermonuclear reactions or auxiliary heating. The present analysis and associated kinetic considerations indicate that steady diffusion-driven operation should become possible for certain classes of plasma profiles, without running into singularity problems at the pinch axis. Such operation leads to higher axial currents in a Z-pinch without an axial magnetic field than in a tokamaklike case under similar plasma conditions. The technical difficulty in realizing a volume distribution of particle sinks introduces certain constraints on the plasma and current profiles. This fact has to be taken into account in a stability analysis. Neoclassical or anomalous diffusion will increase the diffusion velocity of the plasma but is not expected to affect the main physical features of the present results

Dynamic stability of self-similar solutions for a plasma pinch

International Nuclear Information System (INIS)

Ma, Sifeng.

1988-01-01

Linear Magnetohydrodynamic (MHD) stability theory is applied to a class of self-similar solutions which describe implosion, expansion and oscillation of an infinitely conducting plasma column. The equations of perturbation are derived in the Lagrangian coordinate system. Numerical procedures via the finite-element method are formulated, and general aspects of dynamic stability are discussed, The dynamic stability of the column when it is oscillatory is studied in detail using the Floquet theory, and the characteristic exponent is calculated numerically. A-pinch configuration is examined. It is found that self-similar oscillations in general destabilize the continua in the MHD spectrum, and parametric instability results

Filamentation and networking of electric currents in dense Z-pinch plasmas

International Nuclear Information System (INIS)

Kukushkin, A.B.; Rantsev-Kartinov, V.A.

2001-01-01

The results of high-resolution processing using the multilevel dynamical contrasting method of earlier experiments on linear Z-pinches are presented which illustrate formation of a dynamical percolating network woven by long-living filaments of electric current. A qualitative approach is outlined which treats long-living filaments as a classical plasma formation governed by the long-range quantum bonds provided, at the microscopical level, by nanotubes of elements of optimal valence. The self-similarity of structuring in laboratory and cosmic plasmas is shown, and examples are found of nanotube-like and/or fullerene-like structures of cosmic length scales. (author)

Filamentation and networking of electric currents in dense Z-pinch plasmas

International Nuclear Information System (INIS)

Kukushkin, A.B.; Rantsev-Kartinov, V.A.

1999-01-01

The results of high-resolution processing using the multilevel dynamical contrasting method of earlier experiments on linear Z-pinches are presented which illustrate formation of a dynamical percolating network woven by long-living filaments of electric current. A qualitative approach is outlined which treats long-living filaments as a classical plasma formation governed by the long-range quantum bonds provided, at the micro-scopical level, by nanotubes of elements of optimal valence. The self-similarity of structuring in laboratory and cosmic plasmas is shown, and examples are found of nanotube-like and/or fullerene-like structures of cosmic length scales. (author)

The belt-screw-pinch reactor and other high-beta systems

International Nuclear Information System (INIS)

Bustraan, M.; Klippel, H.Th.; Veringa, H.J.; Verschuur, K.A.

1981-01-01

In a screw-pinch reactor the expenditure for plasma implosion and compression can be reduced and the reacting volume and burn time can be enlarged. This is possible by pinch ignition of only a few percent of the fuel. Fusion energy then ignites injected fuel pellets and expands the plasma. The magnitude of the pulsed magnetic fields is such as to make the application of superconducting coils feasible. An economical reactor model is described. A comparison is made with tokamak and reversed field pinch reactor designs. (author)

Developments of sausages in a z-pinch with short-wave perturbation of a boundary

International Nuclear Information System (INIS)

Vikhrev, V.V.; Ivanov, V.V.; Rozanova, G.A.

1989-01-01

A numeric simulation of sausage evolution in z-pinch during short-wave excitation of the boundary of plasma column pinch is carried out. The simulation has shown that due to nonlinear development of sausages in a pinch plasma colomn the cavities filled with a magnetic field in a rarefied pinch plasma are formed. Simultaneously compact column of tense plasma whose temperature is much higher than the average temperature of pinch plasma column are formed on the pinch axis. In the region of inlet in the cavity plasma is radially directed due to ponderomotoric force 1/2 x jB up to velocities greatly increasing the thermal velocity of ions in a plasma column

Mechanism of neutron generation in Z-pinches

International Nuclear Information System (INIS)

Vikhrev, V.V.

1986-01-01

The review of experimental and theoretical investigations in a mechanism of neutron generation in Z-pinches is presented. Special attention is paid to the thermonuclear mechanism of neutron generation occuring due to the formation of high-temperature plasma regions in Z-pinch sausage-type instabilities. This mechanism is shown to be predominant in charges with the neutron yield more than 10 9 per a charge. Experimental data, which are considered to be contradicting to thermonuclear nature of neutron radiation, are explained

Seeded perturbations in wire array Z-Pinches

International Nuclear Information System (INIS)

Robinson, Allen Conrad; Fedin, Dmitry; Kantsyrev, Victor Leonidovich; Wunsch, Scott Edward; Oliver, Bryan Velten; Lebedev, Sergey V.; Coverdale, Christine Anne; Ouart, Nicholas D.; LePell, Paul David; Safronova, Alla S.; Shrestha, I.; McKenney, John Lee; Ampleford, David J.; Rapley, J.; Bott, S.C.; Palmer, J.B.A.; Sotnikov, Vladimir Isaakovich; Bland, Simon Nicholas; Ivanov, Vladimir V.; Chittenden, Jeremy Paul; Jones, B.; Garasi, Christopher Joseph; Hall, Gareth Neville; Yilmaz, M. Faith; Mehlhorn, Thomas Alan; Deeney, Christopher; Pokala, S.; Nalajala, V.

2005-01-01

Controlled seeding of perturbations is employed to study the evolution of wire array z-pinch implosion instabilities which strongly impact x-ray production when the 3D plasma stagnates on axis. Wires modulated in radius exhibit locally enhanced magnetic field and imploding bubble formation at discontinuities in wire radius due to the perturbed current path. Wires coated with localized spectroscopic dopants are used to track turbulent material flow. Experiments and MHD modeling offer insight into the behavior of z-pinch instabilities.

Z-pinch driven hohlraums design for the 100 nanoseconds current time scale

International Nuclear Information System (INIS)

Hamann, F.

2003-12-01

This work estimates Z-pinch driven hohlraums capabilities to obtain high temperatures (>200 eV). Simple models are proposed to calculate the performances offered by currents of 5 to 100 MA in 100 ns. The one dimensional physics of the Z-pinch at the length scale of its thickness and the hydrodynamics instabilities are studied. Then the enhancement of hohlraums performances with double nested Z-pinches or the use of an axial magnetic field is analysed. Z-pinch direct drive approach for inertial confinement fusion is finally considered. All the presented results are based on theoretical and 2D numerical approach and on the analysis of experimental results which were obtained on the american 'Z' generator. Annexes recall radiation MHD equations and check their validity for Z-pinch implosion. (author)

Experimental study of the 'NOVA' Z-pinch equipment working as vacuum-gap

International Nuclear Information System (INIS)

Acuna, H.; Bernal, L.; Cortazar, D.; Iglesias, G.; Pouzo, J.

1990-01-01

The Z-pinch device 'NOVA' (2 kjoule, 10 kV, 250 kA) is operated as a vacuum gap. The plasma is generated in high vacuum (10 -5 mb) by the material let loose from the copper electrodes. Many strong compressions (micro pinches) are produced in the pinch column over the first quarter of the current period. This is detected by the observable pulses in the dI/dt signal. Hard X-rays generated in coincidence with the micro pinches are detected using a scintillator-photomultiplier system. This work studies the plasma evolution, by taking pictures of the pinch with obturation times of about 15 ns, temporally correlated with the dI/dt signal. Instabilities of types m=0 and m=1 are observed. (Author). 3 refs., 6 figs

The effects of shoulder load and pinch force on electromyographic activity and blood flow in the forearm during a pinch task

DEFF Research Database (Denmark)

Visser, Bart; Kofoed Nielsen, Pernille; de Kraker, Heleen

2006-01-01

loaded with 4.95 kg each) were combined with intermittent pinch forces at 0, 10 and 25% of the maximum voluntary contraction (MVC). Blood flow to the forearm was measured with Doppler ultrasound. Myoelectric activity of the forearm and neck-shoulder muscles was recorded to check for the workload levels....... Across all levels of shoulder load, blood flow increased significantly with increasing pinch force (21% at 10% MVC and by 44% at 25% MVC). Blood flow was significantly affected by shoulder load, with the lowest blood flow at the highest shoulder load. Interactions of pinch force and shoulder load were....... The results of this study indicate that shoulder load might influence blood flow to the forearm....

PBFA Z: A 20-MA z-pinch driver for plasma radiation sources

International Nuclear Information System (INIS)

Spielman, R.B.; Breeze, S.F.; Deeney, C.

1996-01-01

Sandia National Laboratories is completing a major modification to the PBFA-II facility. PBFA Z will be a z-pinch driver capable of delivering up to 20 MA to a z-pinch load. It optimizes the electrical coupling to the implosion energy of z pinches at implosion velocities of ∼ 40 cm/μs. Design constraints resulted in an accelerator with a 0.12-Ω impedance, a 10.25-nH inductance, and a 120-ns pulse width. The design required new water transmission lines, insulator stack, and vacuum power feeds. Current is delivered to the z-pinch load through four, self-magnetically-insulated vacuum transmission lines and a double post-hole convolute. A variety of design codes are used to model the power flow. These predict a peak current of 20 MA to a z-pinch load having a 2-cm length, a 2-cm radius, and a 15--mg mass, coupling 1.5 MJ into kinetic energy. We present 2-D Rad-Hydro calculations showing MJ x-ray outputs from tungsten wire-array z pinches

Dynamical analysis of surface-insulated planar wire array Z-pinches

Science.gov (United States)

Li, Yang; Sheng, Liang; Hei, Dongwei; Li, Xingwen; Zhang, Jinhai; Li, Mo; Qiu, Aici

2018-05-01

The ablation and implosion dynamics of planar wire array Z-pinches with and without surface insulation are compared and discussed in this paper. This paper first presents a phenomenological model named the ablation and cascade snowplow implosion (ACSI) model, which accounts for the ablation and implosion phases of a planar wire array Z-pinch in a single simulation. The comparison between experimental data and simulation results shows that the ACSI model could give a fairly good description about the dynamical characteristics of planar wire array Z-pinches. Surface insulation introduces notable differences in the ablation phase of planar wire array Z-pinches. The ablation phase is divided into two stages: insulation layer ablation and tungsten wire ablation. The two-stage ablation process of insulated wires is simulated in the ACSI model by updating the formulas describing the ablation process.

Magnetostatic Analysis of a Pinch Mode Magnetorheological Valve

Directory of Open Access Journals (Sweden)

Gołdasz Janusz

2017-09-01

Full Text Available The study deals with the pinch mode of magnetorheological (MR fluids’ operation and its application in MR valves. By applying the principle in MR valves a highly non-uniform magnetic field can be generated in flow channels in such a way to solidify the portion of the material that is the nearest to the flow channel’s walls. This is in contrary to well-known MR flow mode valves. The authors investigate a basic pinch mode valve in several fundamental configurations, and then examine their magnetic circuits through magnetostatic finite-element (FE analysis. Flux density contour maps are revealed and basic performance figures calculated and analysed. The FE analysis results yield confidence in that the performance of MR pinch mode devices can be effectively controlled through electromagnetic means.

Direction of Impurity Pinch and Auxiliary Heating in Tokamak Plasmas

International Nuclear Information System (INIS)

Angioni, C.; Peeters, A.G.

2006-01-01

A mechanism of particle pinch for trace impurities in tokamak plasmas, arising from the effect of parallel velocity fluctuations in the presence of a turbulent electrostatic potential, is identified analytically by means of a reduced fluid model and verified numerically with a gyrokinetic code for the first time. The direction of such a pinch reverses as a function of the direction of rotation of the turbulence in agreement with the impurity pinch reversal observed in some experiments when moving from dominant auxiliary ion heating to dominant auxiliary electron heating

Torus C-I field reversed theta-pinch at UNICAMP

International Nuclear Information System (INIS)

Machida, M.; Collares, M.P.; Honda, R.Y.; Sakanaka, P.H.; Scheid, V.H.B.

1984-01-01

The influence of multipole fields (octopole and quadrupole) on supressing the n=2 rotational instability, field reconnection, particle loss effects is studied, and the viability of transforming the theta-pinch from Campinas, Brazil (100Kv, 55Kj) to the field reversed theta-pinch with plasma translation program is analyzed. (E.G.) [pt

Preliminary study of Rayleigh-Taylor instability in wire-array Z-pinch

International Nuclear Information System (INIS)

He Kaihui; Feng Kaiming; Li Qiang; Gao Chunming

2000-01-01

It is important to research into the MHD Rayleigh-Taylor instability developed in Z-pinch implosion. A snowplough model of the single wire Z-pinch is presented. The perturbation amplitude of Rayleigh-Taylor instability in the wire-array Z-pinch is analyzed quantitatively. Sheared axial flow is put forward to mitigate and reduce the Rayleigh-Taylor instability. And other approaches used to mitigate MHD instability in such a super-fast process are explored

A study of reversed field pinch experiments using a new programming mode

International Nuclear Information System (INIS)

Kita, Y.

1979-08-01

A new mode of external-field programming for setting up a reversed-field pinch (RFP) is tested in STP-1. It involves creating an initial plasma with a screw pinch followed by external-field reversal. The program is done carefully so as to satisfy the equilibrium relation with respect to the minor radius throughout the setting-up phase. Increase of the trapped flux in the plasma by a factor of two is consequently attained, as compared with previous usual programming mode. Actually, at a plasma current of 58 kA, a stable operation time of 13 μsec is achieved with a density of 3.5 x 10 15 cm -3 and a temperature of 20 eV. After 13 μsec stable operation time, the plasma is suddenly crashed down by a violent MHD instability. One dimensional stability analysis based on ideal MHD model is applied to the experimental results. It is found that the instability is m = 1 resistive tearing mode under the influence of viscosity. Using the new programming high current operation at 110 kA is done and results in higher plasma temperature and density of 40 eV and 4.5 x 10 15 cm -3 , respectively. The duration of stable discharge, however, is limited to about 10 μsec, in spite of the expected longer confinement time at the higher temperature. (author)

Linking natural microstructures with numerical modeling of pinch-and-swell structures

Science.gov (United States)

Peters, Max; Berger, Alfons; Herwegh, Marco; Regenauer-Lieb, Klaus

2016-04-01

dominated deformation at relatively high extensional strains in the pinches. The numerical simulations indicate that viscosity weakening due to dissipated heat from grain size reduction marks the onset of localization, resulting in continuous necking of the layer. Interestingly, there exist multiple steady states, i.e. a first homogeneous state out of which localization arises, steady states of the stable end-member structure, expressed by homogeneous conditions in both pinches and swells, and in the surrounding matrix, the latter obeying a linear rheology. Based on our microstructural and numerical results, we suggest that the onset of localization represents a fundamental material bifurcation. This implies that the studied structures can be described as ductile instabilities. Finally, we discuss the profound role of the energy theory of localization described here, which allows deriving the paleo-deformation conditions, as well as fundamental material properties in a self-consistent manner. REFERENCES Herwegh, M., Poulet, T., Karrech, A. and Regenauer-Lieb, K. (2014): Journal of Geophysical Research 119, doi:10.1002/2013JB010701 Peters, M., Veveakis, M., Poulet, T., Karrech, A., Herwegh, M. and Regenauer-Lieb, K. (2015): Journal of Structural Geology 78, doi:10.1016/j.jsg.2015.06.005

Metal Wire-array Load for Z-pinch Used as X-ray Source

Institute of Scientific and Technical Information of China (English)

1999-01-01

<正> The inertial confinement fusion （ICF） has evident minatory applications becasuse ICF ignites the fusion fuel with high energy media. As a method of ICF, Z-pinch has obtained evidently increased X-ray power PX-ray and energy EX-ray. The scientists have noticed this promising achievement. The Z-accelerator which is an operating Z-pinch device in Sandia national laboratory （SNL） in USA achieved 290 TW Px-ray in 1997 and the energy and defense departments of USA will finance SNL for a larger Z-pinch device. The early Z-pinch aimed to obtain high tempera

Construction of double discharge pulsed electron beam generator and its applications

International Nuclear Information System (INIS)

Goektas, H.

2001-12-01

Generation of fast pulsed electron beam by superposing DC and pulsed hollow cathode discharge is studied. The electrical characteristics and measurements of the electron beam generator are done dc glow discharge and for the pulsed one. The electron beam current, its density and magnetic field effect, pinch effect, have been studied. The dependence of the electron beam parameters with respect to pressure and magnetic field have been studied. The pulsing effect of the beam is reviewed. By using the generator, micron holes drilling and carbon deposition was done at the laboratory. As a target source for carbon deposition methane gas is used and for Hydrogen-free carbon deposition was graphite

Radiative collapse of a Bennett-relaxed z-pinch

International Nuclear Information System (INIS)

Turner, L.

1989-01-01

The global evolution of a z-pinch has been studied with the assumption of a relaxed state consisting of ions and electrons, each in a rigidly drifting isothermal Maxwellian distribution. This speculative approach has the pragmatic feature of possessing phenomenologically useful global parameters such as drift velocity and temperature that vary in accordance with global physical quantities such as energy and entropy. The plasma gains energy from a time-dependent electric field by means of Poynting's vector. Coulomb collisions between electrons and ions is calculated with a Fokker-Planck treatment analogous to that used by Dreicer to calculate runaways. For a variety of initial conditions and time-independent applied electric fields, the pinch evolution always culminates in a time-independent (attractor) state whose current is the Pease-Braginskii current and whose final radius is proportional to (line density)/sup 3/4//(electric field)/sup 1/2/. Before the final state is attained, the pinch may bounce toward and away from a highly collapsed state. For the case of a Bennett pinch, the classical limit of the resistivity is attained when the line density is much greater than 4πm/sub e//e 2 μ/sub o/; i.e., 3.55 /times/ 10 14 m/sup /minus/1/. 6 refs., 2 figs

Deuterated fibre Z-pinch on the S-300 generator

NARCIS (Netherlands)

Klir, D.; Kravarik, J.; Kubes, P.; Bakshaev, Yu L.; Blinov, P. I.; Chernenko, A. S.; Danko, S. A.; Korolev, V. D.; Ustroev, G. I.; Ivanov, M. I.; Cai, Hongchun

2006-01-01

Dense Z-pinch experiments were carried out on the S-300 generator (3.5 MA, 100 ns, 0.15 Omega) at the Kurchatov Institute in Moscow. The experiments were performed at a peak current of 2 MA with a rise time of about 100 ns. The Z-pinch was formed from a deuterated polyethylene fibre of 100 mu m

Vacuum ultraviolet emission from argon, krypton, and xenon in a radial-viewed theta pinch

International Nuclear Information System (INIS)

Engleman, R. Jr.; Thomson, D.B.; Monaghan, D.A.

1976-03-01

Vacuum ultraviolet line emission from argon, krypton, and xenon (5 percent in deuterium) has been observed from a plasma (approximately 50 eV and N/sub e/ approximately 10 17 /cm 3 ) produced by the Scyllar linear theta-pinch device. More than 50 emission lines in the 30- to 500-A region have been measured for each gas mixture. Some lines have been identified as due to Ar VII through XI, Kr IX and X, and Xe IX, but many lines remain unassigned

PBFA Z: A 60-TW/5-MJ Z-pinch driver

International Nuclear Information System (INIS)

Spielman, R.B.; Deeney, C.; Chandler, G.A.; Douglas, M.R.; Fehl, D.L.; Matzen, M.K.; McDaniel, D.H.; Nash, T.J.; Porter, J.L.; Sanford, T.W.; Seamen, J.F.; Stygar, W.A.; Struve, K.W.; Breeze, S.P.; McGurn, J.S.; Torres, J.A.; Zagar, D.M.; Gilliland, T.L.; Jobe, D.O.; McKenney, J.L.; Mock, R.C.; Vargas, M.; Wagoner, T.; Peterson, D.L.

1997-01-01

PBFA Z, a new 60-TW/5-MJ electrical accelerator located at Sandia National Laboratories, is now the world's most powerful z-pinch driver. PBFA Z stores 11.4 MJ in its 36 Marx generators, couples 5 MJ into a 60-TW/105-ns FWHM pulse to the 120-mΩ water transmission lines, and delivers 3.0 MJ and 50 TW of electrical energy to the z-pinch load. Depending on load parameters, we attain peak load currents of 16-20 MA with a current rise time of ∼105ns with wire-array z-pinch loads. We have extended the x-ray performance of tungsten wire-array z pinches from earlier Saturn experiments. Using a 2-cm-radius, 2-cm-long tungsten wire array with 240, 7.5-μm diameter wires (4.1-mg mass), we achieved an x-ray power of 210 TW and an x-ray energy of 1.9 MJ. Preliminary spectral measurements suggest a mostly optically-thick, Planckian-like radiator below 1000 eV. Data indicate ∼100kJ of x rays radiated above 1000 eV. An intense z-pinch x-ray source with an overall coupling efficiency greater than 15% has been demonstrated. copyright 1997 American Institute of Physics

The stability of a constricted gas discharge

Energy Technology Data Exchange (ETDEWEB)

Tayler, R J [U.K. Atomic Energy Authority, AERE, Harwell (United Kingdom)

1958-07-01

This paper is to be regarded as a progress report on an unfinished problem and an indication is given of aspects of the problem which, it is hoped, will be studied soon. Two theoretical models are considered here. The first approach is extremely naive: plasma dynamics is completely neglected and only the forces exerted by the electromagnetic field are considered. The second approach is to use Maxwell's equations combined with a simple one-fluid hydrodynamics - classical hydromagnetics. The paper is arranged as follows: the magnetostatic or extensible wire model of the discharge is studied; based on the hydromagnetic equations: 1) the gradual loss of stability of the stabilised pinch, due to field diffusion, is discussed and 2) another type of stable discharge configuration is introduced. In the final section there is a discussion of further problems which must be studied.

A high-voltage triggered pseudospark discharge experiment

International Nuclear Information System (INIS)

Ramaswamy, K.; Destler, W.W.; Rodgers, J.

1996-01-01

The design and execution of a pulsed high-voltage (350 endash 400 keV) triggered pseudospark discharge experiment is reported. Experimental studies were carried out to obtain an optimal design for stable and reliable pseudospark operation in a high-voltage regime (approx-gt 350 kV). Experiments were performed to determine the most suitable fill gas for electron-beam formation. The pseudospark discharge is initiated by a trigger mechanism involving a flashover between the trigger electrode and hollow cathode housing. Experimental results characterizing the electron-beam energy using the range-energy method are reported. Source size imaging was carried out using an x-ray pinhole camera and a novel technique using Mylar as a witness plate. It was experimentally determined that strong pinching occurred later in time and was associated with the lower-energy electrons. copyright 1996 American Institute of Physics

Self-pinched transport of intense ion beams

International Nuclear Information System (INIS)

Ottinger, P.F.; Neri, J.M.; Stephanakis, S.J.

1999-01-01

Electron beams with substantial net currents have been routinely propagated in the self-pinched mode for the past two decades. However, as the physics of gas breakdown and beam neutralization is different for ion beams, previous predictions indicated insufficient net current for pinching so that ion beam self-pinched transport (SPT) was assumed impossible. Nevertheless, recent numerical simulations using the IPROP code have suggested that ion SPT is possible. These results have prompted initial experiments to investigate SPT of ion beams. A 100-kA, 1.2-MeV, 3-cm-radius proton beam, generated on the Gamble II pulsed-power accelerator at NRL, has been injected into helium in the 30- to 250-mTorr regime to study this phenomenon. Evidence of self-pinched ion beam transport was observed in the 35- to 80-mTorr SPT pressure window predicted by IPROP. Measured signals from a time- and space-resolved scattered proton diagnostic and a time-integrated Li(Cu) nuclear activation diagnostic, both of which measure protons striking a 10-cm diameter target 50 cm into the transport region, are significantly larger in this pressure window than expected for ballistic transport. These results are consistent with significant self-magnetic fields and self-pinching of the ion beam. On the other hand, time-integrated signals from these same two diagnostics are consistent with ballistic transport at pressures above and below the SPT window. Interferometric electron line-density measurements, acquired during beam injection into the helium gas, show insignificant ionization below 35 mTorr, a rapidly rising ionization fraction with pressure in the SPT window, and a plateau in ionization fraction at about 2% for pressures above 80 mTorr. These and other results are consistent with the physical picture for SPT. IPROP simulations, which closely model the Gamble II experimental conditions, produce results that are in qualitative agreement with the experimental results. The advantages of SPT for

Plasma dynamics in a staged pinch device

International Nuclear Information System (INIS)

Khattak, N.A.D.; Ahmed, Z.; Mirza, A.M.; Murtaza, G.

1998-01-01

Plasma parameters in fiber initiated fast and dense theta-pinch plasma driven by an annular finite-thickness gas-puff Z-pinch are studied. The imploding gas-puff Z-pinch plasma traps an axial magnetic field B/sub z/, compressing it to large values (of the order of several megagauss) in an extremely short time. The rapidly changing magnetic flux of this field induces an azimuthal current on the surface of the coaxially placed fiber, with a rise time an order of magnitude shorter than the applied Z-pinch current. The shorter rise time of the current stabilizes the pinch against sausage mode of MHD instabilities. Our numerical results demonstrate that for a relatively thick gas-puff layer, the compression occurs before the current saturates. At the peak compression the fuel densities of the order of 10/sup 25/ cm/sup -3/ and temperature above 10 keV can be achieved on a time scale of 0.1 nanoseconds, yielding the Lawson Criterion parameters n tau is approximately equal to 10/sup 14/ sec cm/sup -3/ for D-T fuel. The snow-plow effect incorporated in our model exercise a strong influence on the onset and growth rate of sausage and Rayleigh-Taylor (R-T) modes of instabilities. Imposing a rotational velocity on the outer thin gas-puff plasma can control the Rayleigh-Taylor instability. Numerical results indicate that the choice of the spin velocity is critical. Large values of the spin velocity, though provide stabilization against the R-T instability at the final stage of compression, however, it adversely reduce the plasma parameters so essential to achieve controlled fusion. Our analysis, therefore, suggests that a judicious choice of the spin velocity is necessary to obtain the desired temperature and density, especially when we seed D-T fiber plasma with a small fraction of high-Z Kr impurity to initiate the radiative collapse. (author)

Investigations of toroidal wave numbers of the kink instabilities in a toroidal pinch plasma

International Nuclear Information System (INIS)

Hamajima, Takataro; Irisawa, Juichi; Tsukada, Tokuaki; Sugito, Osamu; Maruyama, Hideaki

1979-01-01

The axial toroidal wave numbers of the kink instability of toroidal pinch plasma were measured and investigated with a specially designed coil, and the results were compared with the MHD theory. The schematic figure and the particulars of the experimental apparatus are briefly illustrated in the first part. The method of generating theta-Z pinch plasma, the wave form of the magnetic flux density in Z-direction and the plasma current are also explained. The 360 deg stereoscopic framing photographs were taken with an image converter camera at the intervals of 0.5 μs after the initiation of the main electric discharge in Z-circuit. From these photographs, the growth of the kink instability was observed. The measured magnetic field distribution at t = 2 μs is presented. In the second part, the radial displacement of plasma and toroidal wave number were measured from the above framing photographs. Then the spectra of plasma displacement were analyzed by the Fourier analysis. The measured results of toroidal wave number was analyzed by both the skin current model and the diffuse current model. Many new results obtained from the present study were mainly derived from the observation of the framing photographs, and they are summarized in the final part of this paper. (Aoki, K.)

UV Laser Diagnostics of the 1-MA Z-pinch Plasmas

International Nuclear Information System (INIS)

Altemara, S. D.; Ivanov, V. V.; Astanovitskiy, A. L.; Haboub, A.

2009-01-01

The 532 nm laser diagnostic set at the Zebra generator shows the details of the ablation and stagnation phases in cylindrical, planar, and star-like wire arrays but it cannot show the structure of the stagnated z-pinch and the implosion in small diameter loads, 1-3 mm in diameter. The absorption increment and the refraction angle of the 532 nm laser, when passing through the plasma, are too great to obtain quality images. An ultraviolet probing beam at the wavelength of 266 nm was developed to study small-diameter loads and to investigate the structure of the 1-MA z-pinch. The UV radiation has a much smaller absorption increment and refraction angles in plasmas than the 532 nm light and allows for better imaging of the z-pinch plasmas. Estimates showed that UV probing would be able to probe the high-density z-pinch plasma in experiments on the Zebra generator, and the early results of UV probing on the Zebra generator have shown promise.

Space and time resolved observations of hot spots dynamics in a vacuum spark discharge

International Nuclear Information System (INIS)

Chuaqui, H.; Favre, M.; Saavedra, R.; Wyndham, E.

1996-01-01

Experimental observations of the plasma formations in a vacuum spark discharge are presented. A low power Nd:YAG laser pulse incident onto a titanium cathode initiates the discharge. The evolution of the titanium plasma electron density and temperature is followed both in the visible and the soft X-ray part of the spectrum. The former uses a novel micro holographic interferometric technique permitting a spatial resolution better than 20 μm. The probing beam is a 6 ns frequency doubled Nd:YAG laser. The latter emission is resolved using a number of different methods. The spatial information is derived from a 1 ns multi framing camera X-ray camera which projects the plasma image using four different slit wire pinhole images and six pinhole images, each aperture being filtered differently. The temporal evolution of the emission of each discharge is followed using several silicon PIN diodes. The x-ray spectrum is unfolded from the filter and detector response and interpreted using a collisional radiative package. The hot spots are seen to form in a submillimeter pinch stemming from the incident laser focus which has a life time about 20 ns. The hot spots are much shorter events, reaching substantially higher densities, but involve only part of the line density of the pinch column. (author). 4 figs., 8 refs

Space and time resolved observations of hot spots dynamics in a vacuum spark discharge

Energy Technology Data Exchange (ETDEWEB)

Chuaqui, H; Favre, M; Saavedra, R; Wyndham, E [Universidad Catolica de Chile, Santiago (Chile). Facultad de Fisica; Choi, P; Dumitrescu-Zoita, C [Ecole Polytechnique, Palaiseau (France). Laboratoire de Physique des Milieux Ionises; Soto, L [Comision Chilena de Energia Nuclear, Santiago (Chile)

1997-12-31

Experimental observations of the plasma formations in a vacuum spark discharge are presented. A low power Nd:YAG laser pulse incident onto a titanium cathode initiates the discharge. The evolution of the titanium plasma electron density and temperature is followed both in the visible and the soft X-ray part of the spectrum. The former uses a novel micro holographic interferometric technique permitting a spatial resolution better than 20 {mu}m. The probing beam is a 6 ns frequency doubled Nd:YAG laser. The latter emission is resolved using a number of different methods. The spatial information is derived from a 1 ns multi framing camera X-ray camera which projects the plasma image using four different slit wire pinhole images and six pinhole images, each aperture being filtered differently. The temporal evolution of the emission of each discharge is followed using several silicon PIN diodes. The x-ray spectrum is unfolded from the filter and detector response and interpreted using a collisional radiative package. The hot spots are seen to form in a submillimeter pinch stemming from the incident laser focus which has a life time about 20 ns. The hot spots are much shorter events, reaching substantially higher densities, but involve only part of the line density of the pinch column. (author). 4 figs., 8 refs.

An analytic model of radiative collapse of a Z-pinch

International Nuclear Information System (INIS)

Haines, M.G.

1989-01-01

There is a critical current I PB of about 1 MA (the Pease-Braginskii current) at which Ohmic heating and bremsstrahlung losses balance in a Z-pinch under pressure equilibrium. An analytic zero-dimensional model shows the process of radiative collapse when the prescribed current exceeds the critical current. In particular for a linearly rising current radiative collapse is complete when the current is 3 I PB . However, in practice the voltage limitation imposed by an external circuit prevents such a total collapse, and by including this in the model a maximum density (10 30 -10 32 m -3 )can occur followed by an expansion and damped oscillation about an equilibrium at which the current equals the Pease-Braginskii current. In the absence of alpha-particle pressure the maximum density is limited by the resistance of the narrow column, the large voltage across which (∼10 8 V) is balanced essentially bu a large negative LI; it occurs when the current is I PB [(δ-1)/(δ-2)] 1/2 where δ=7/3+4/3 In(R/a), where a is the pinch radius and R is the radius of the current return. The minimum current following maximum density is shown to be greater than I PB /√2. Degeneracy effects can be included in the model. (author) 5 refs., 1 fig

An analytic model of radiative collapse of a Z-pinch

International Nuclear Information System (INIS)

Haines, M.G.

1989-01-01

There is a critical current I PB of about 1 MA (the Pease-Braginskii current) at which Ohmic heating and Bremsstrahlung losses balance in a Z-pinch under pressure equilibrium. An analytic zero-dimensional model shows the process of radiative collapse when the prescribed current exceeds the critical current. In particular for a linearly rising current radiative collapse is complete when the current is √3 I PB . However in practice the voltage limitation imposed by an external circuit prevents such a total collapse, and by including this in the model a maximum density (∼ 10 30 -10 32 m -3 ) can occur followed by an expansion and damped oscillation about an equilibrium at which the current equals the Pease-Braginskii current. In the absence of alpha-particle pressure the maximum density is limited by the resistance of the narrow column, the large voltage across which (∼ 10 8 V) is balanced essentially by a large negative LI radical; it occurs when the current is I PB [(δ-1)/(δ-2)] 1/2 where δ = 7/3+4/3 1n (R w /a), where a is the pinch radius and R w is the radius of the current return. The minimum current following maximum density is shown to be greater than I PB /√2. Degeneracy effects can be included in the model. (author)

X-Pinch soft x-ray source for microlithography

International Nuclear Information System (INIS)

Glidden, S.C.; Hammer, D.A.; Kalantar, D.H.; Qi, N.

1993-01-01

The x-pinch soft x-ray source is described for application in submicron resolution lithography. Experiments have been performed to characterize the radiation emitted from magnesium wire x-pinch plasmas using an 80 ns, ≤500 kA pulse. Yields of 14.2 J averaged over three independent calibrated diagnostics at 445 kA have been measured in magnesium K-shell radiation (predominantly 8.4 angstrom to 9.4 angstrom or 1.5 keV to 1.3 keV) from a submillimeter source, with as little as 5-10% of the yield below the 6.74 angstrom silicon absorption edge. A new ≤700 kA, 100 ns pulser being used for x-pinch physics experiments is described. The design of a 40 pulse per second pulsed power system and wire loading mechanism for exposing a resist in 1 second at a distance 40 cm is presented

Putting the pinch on reactors

International Nuclear Information System (INIS)

Glavic, P.; Kravanja, Z.; Homsak, M.

1990-01-01

Pinch technology has proven to be a powerful tool for designing new processes and retrofitting old ones. But, until recently, it was thought to pertain only to heat exchanger networks, separators and power devices (such as heat engines and heat pumps). Regarded as process background, reactors have been left out of heat integrations. Their structure, however, can be changed and, within limits, their parameters modified to better exploit energy. In a pinch-designed plant, heat is transferred between the hot and cold process streams so efficiently that the plant's utility requirements (heat sources and sinks) are minimal. The design procedure is discussed. It involves two steps: finding a nearly optimal process structure by means of an analysis of process-temperature-vs.- enthalpy diagrams, and then optimizing the structure by means of grid diagrams or a computerized procedure

Growth of linear Ni-filled carbon nanotubes by local arc discharge in liquid ethanol

Energy Technology Data Exchange (ETDEWEB)

Sagara, Takuya [Department of Electric Engineering, Graduated School of Science and Technology, Nihon University, 1-8-14 Surugadai Kanda, Chiyoda, Tokyo 101-8308 (Japan); Kurumi, Satoshi [Department of Electric Engineering, College of Science and Technology, Nihon University, 1-8-14 Surugadai Kanda, Chiyoda, Tokyo 101-8308 (Japan); Suzuki, Kaoru, E-mail: kaoru@ele.cst.nihon-u.ac.jp [Department of Electric Engineering, College of Science and Technology, Nihon University, 1-8-14 Surugadai Kanda, Chiyoda, Tokyo 101-8308 (Japan)

2014-02-15

The cylindrical geometry of carbon nanotubes (CNTs) allows them to be filled with metal catalysts; the resulting metal-filled CNTs possess different properties depending on the filler metal. Here we report the synthesis of Ni-filled CNTs in which Ni is situated linearly and homogeneously by local arc discharge in liquid ethanol. The structural characteristics of synthesized Ni-filled CNTs were determined by transmission electron microscopy (TEM), and the relationship between pyrolysis conditions and the length and diameter of Ni-filled CNTs was examined. The encapsulated Ni was identified by a TEM-equipped energy-dispersive X-ray spectroscope and found to have a single-crystal fcc structure by nano-beam diffraction. The features of linear Ni-filled CNT are expected to be applicable to probes for magnetic force microscopy.

Stage theta pinch experiments

International Nuclear Information System (INIS)

Linford, R.K.; Downing, J.N.; Gribble, R.F.; Jacobson, A.R.; Platts, D.A.; Thomas, K.S.

1975-01-01

The Staged Theta Pinch program is designed to study the technological and physics problems associated with producing fat plasmas and separating the implosion heating from the adiabatic compression. Several methods of implosion heating are discussed. Circuit diagrams and theoretical magnetic field behavior are described for the STP and resonant heating experiments. (MOW)

Filamentation instability of a self-pinched hollow electron beam

International Nuclear Information System (INIS)

Uhm, H.S.; Hughes, T.P.

1986-01-01

Filamentation stability properties of a self-pinched hollow electron beam propagating through a collisional plasma channel are investigated within the framework of linearized Vlasov--Maxwell equations, assuming that the beam is thin and that the equilibrium and perturbed space-charge fields are neutralized by background plasma. It is further assumed that the perturbations are well tuned with kβ/sub b/c+lω/sub b/ and satisfy la 0 , where l and k are the azimuthal and axial wavenumbers, β/sub b/c and ω/sub b/ are the axial velocity and the rotational frequency of the beam, and 2a and R 0 are the thickness and mean radius of the beam. From the stability analysis, two distinctive unstable mechanisms are identified: the return-current driven instability and the resistively driven instability. It is also found that high-l-mode perturbations are easily stabilized by a spread in the canonical angular momentum. Making use of a linearized particle-in-cell code, numerical simulations are performed. The agreement between the analytical results and those of simulations is excellent

Electron-Cloud Pinch Dynamics in Presence of Lattice Magnet Fields

CERN Document Server

Franchetti, G

2011-01-01

The pinch of the electron cloud due to a passing proton bunch was extensively studied in a field free region and in a dipolar magnetic field. For the latter study, a strong field approximation helped to formulate the equations of motion and to understand the complex electron pinch dynamics, which exhibited some similarities with the field-free situation. Here we extend the analysis to the case of electron pinch in quadrupoles and in sextupoles. We discuss the limits of validity for the strong field approximation and we evaluate the relative magnitude of the peak tune shift along the bunch expected for the different fields.

Experiments on the ZT-S reversed-field pinch, August--December 1978

International Nuclear Information System (INIS)

Jacobson, A.R.

1979-06-01

During the latter half of 1978 the ZT-S reversed-field pinch was used to explore the utility of pitch-programming techniques in setting up stable diffuse pinch profiles. Several experimental observations relating to this goal are presented

Ion heating and MHD dynamo fluctuations in the reversed field pinch

International Nuclear Information System (INIS)

Scime, E.E.

1992-05-01

Ion temperature measurements, time resolved to 10 μs, have been made in the Madison Symmetric Torus (MST) reversed field pinch (RFP) with a five channel charge exchange analyzer. The characteristic anomalously high ion temperature of RFP discharges has been observed in the MST. The evolution of the ion and electron temperature, as well as density and charge exchange power loss, were measured for a series of reproducible discharges. The ion heating expected from collisional processes with the electrons is calculated and shown too small to explain the measured ion temperatures. The charge exchange determined ion temperature is also compared to measurements of the thermally broadened CV 227.1 nm line. The ion temperature, T i ∼ 250 eV for I = 360 kA, increases by more than 100% during discrete dynamo bursts in MST discharges. Magnetic field fluctuations in the range 0.5 endash 5 MHz were also measured during the dynamo bursts. Structure in the fluctuation frequency spectrum at the ion cyclotron frequency appears as the bursts terminate, suggesting that the mechanism of ion heating involves the dissipation of dynamo fluctuations at ion cyclotron frequencies. Theoretical models for ion heating are reviewed and discussed in light of the experimental results. Similar electron heating mechanisms may be responsible for the discrepancy between measured and expected loop voltages in the RFP. The electrons, as well as the ions, may be heated by turbulent mechanisms, and a RFP energy budget including such phenomena is described

Developing models for simulation of pinched-beam dynamics in heavy ion fusion. Revision 1

International Nuclear Information System (INIS)

Boyd, J.K.; Mark, J.W.K.; Sharp, W.M.; Yu, S.S.

1984-01-01

For heavy-ion fusion energy applications, Mark and Yu have derived hydrodynamic models for numerical simulation of energetic pinched-beams including self-pinches and external-current pinches. These pinched-beams are applicable to beam propagation in fusion chambers and to the US High Temperature Experiment. The closure of the Mark-Yu model is obtained with adiabatic assumptions mathematically analogous to those of Chew, Goldberger, and Low for MHD. Features of this hydrodynamic beam model are compared with a kinetic treatment

Producing High-Performance, Stable, Sheared-Flow Z-Pinches in the FuZE project

Science.gov (United States)

Golingo, R. P.; Shumlak, U.,; Nelson, B. A.; Claveau, E. L.; Forbes, E. G.; Stepanov, A. D.; Weber, T. R.; Zhang, Y.; McLean, H. S.; Tummel, K. K.; Higginson, D. P.; Schmidt, A. E.; University of Washington (UW) Collaboration; Lawrence Livermore National Laboratory (LLNL) Collaboration

2017-10-01

The Fusion Z-Pinch Experiment (FuZE) has made significant strides towards generating high-performance, stable Z-pinch plasmas with goals of ne = 1018 cm-3 and T =1 keV. The Z-pinch plasmas are stabilized with a sheared axial flow that is driven by a coaxial accelerator. The new FuZE device has been constructed and reproduces the major scientific achievements the ZaP project at the University of Washington; ne = 1016 cm-3,T = 100 eV, r20 μs. These parameters are measured with an array of magnetic field probes, spectroscopy, and fast framing cameras. The plasma parameters are achieved using a small fraction of the maximum energy storage and gas injection capability of the FuZE device. Higher density, ne = 5×1017 cm-3, and temperature, T = 500 eV, Z-pinch plasmas are formed by increasing the pinch current. At the higher voltages and currents, the ionization rates in the accelerator increase. By modifying the neutral gas profile in the accelerator, the plasma flow from the accelerator is maintained, driving the flow shear. Formation and sustainment of the sheared-flow Z-pinch plasma will be discussed. Experimental data demonstrating high performance plasmas in a stable Z-pinches will be shown. This work is supported by an award from US ARPA-E.

Wiebel instability of microwave gas discharge in strong linear and circular pulsed fields

International Nuclear Information System (INIS)

Shokri, B.; Ghorbanalilu, M.

2004-01-01

Being much weaker than the atomic fields, the gas breakdown produced by high-power pulsed microwave fields is investigated in the nonrelativistic case. The distribution function of the electrons produced by the interaction with intense linearly and circularly polarized microwave fields is obtained and it is shown that it is in a nonequilibrium state and anisotropic. The discharge mechanism for the gas atoms is governed by electron-impact avalanche ionization. By analyzing the instability of the system and by finding its growth rate, it is shown that the instability which is governed by the anisotropic property of the distribution function is Wiebel instability

Self-stabilized pinch (SSP) concept

International Nuclear Information System (INIS)

Sugisaki, Kiwamu; Hirano, Keiichi.

1985-01-01

Self-Stabilized pinch (SSP) consept is revealed. SSP providcs many attractive features for application to a fusion reactor. Design studies for high temperature plasma production are carried out. Use of adiabatic compression leads to a remarkable reduction of required power source. (author)

Quasi-steady accelerator operation on the ZAP flow Z-pinch

Energy Technology Data Exchange (ETDEWEB)

Hughes, M. C., E-mail: mchugs@uw.edu; Shumlak, U., E-mail: mchugs@uw.edu; Golingo, R. P., E-mail: mchugs@uw.edu; Nelson, B. A., E-mail: mchugs@uw.edu; Ross, M. P., E-mail: mchugs@uw.edu [Aerospace and Energetics Research Program, University of Washington, Seattle, WA 98195 (United States)

2014-12-15

The ZaP Flow Z-Pinch Experiment utilizes sheared flows to stabilize an otherwise unstable equilibrium. The sheared flows are maintained by streaming high velocity plasma parallel to the pinch. Previous operations of the machine show depletion of the accelerator’s neutral gas supply late in the pulse leading to pinch instability. The current distribution in the accelerator exhibits characteristic modes during this operation, which is corroborated by interferometric signals. The decrease in density precipitates a loss of plasma quiescence in the pinch, which occurs on a timescale related to the flow velocity from the plasma source. To abate the depletion, the geometry of the accelerator is altered to increase the neutral gas supply. The design creates a standing deflagration front in the accelerator that persists for the pulse duration. The new operating mode is characterized by the same diagnostics as the previous mode. The lessons learned in the accelerator operations have been applied to the design of a new experiment, ZaP-HD. This work was supported by grants from the Department of Energy and the National Nuclear Security Administration.

Model of enhanced energy deposition in a Z-pinch plasma

International Nuclear Information System (INIS)

Velikovich, A. L.; Davis, J.; Thornhill, J. W.; Giuliani, J. L. Jr.; Rudakov, L. I.; Deeney, C.

2000-01-01

In numerous experiments, magnetic energy coupled to strongly radiating Z-pinch plasmas exceeds the thermalized kinetic energy, sometimes by a factor of 2-3. An analytical model describing this additional energy deposition based on the concept of macroscopic magnetohydrodynamic (MHD) turbulent pinch heating proposed by Rudakov and Sudan [Phys. Reports 283, 253 (1997)] is presented. The pinch plasma is modeled as a foam-like medium saturated with toroidal ''magnetic bubbles'' produced by the development of surface m=0 Rayleigh-Taylor and MHD instabilities. As the bubbles converge to the pinch axis, their magnetic energy is converted to thermal energy of the plasma through pdV work. Explicit formulas for the average dissipation rate of this process and the corresponding contribution to the resistance of the load, which compare favorably to the experimental data and simulation results, are presented. The possibility of using this enhanced (relative to Ohmic heating) dissipation mechanism to power novel plasma radiation sources and produce high K-shell yields using long current rise time machines is discussed. (c) 2000 American Institute of Physics

Steady state theta pinch concept for slow formation of FRC

International Nuclear Information System (INIS)

Hirano, K.

1987-05-01

A steady state high beta plasma flow through a channel along the magnetic field increasing downstream can be regarded as a ''steady state theta pinch'', because if we see the plasma riding on the flow we should observe very similar process taking place in a theta pinch. Anticipating to produce an FRC without using very high voltage technics such as the ones required in a conventional theta pinch, we have studied after the analogy a ''steady state reversed field theta pinch'' which is brought about by steady head-on collision of counter plasma streams along the channel as ejected from two identical co-axial plasma sources mounted at the both ends of the apparatus. The ideal Poisson and shock adiabatic flow models are employed for the analysis of the steady colliding process. It is demonstrated that an FRC involving large numbers of particles is produced only by the weak shock mode which is achieved in case energetic plasma flow is decelerated almost to be stagnated through Poisson adiabatic process before the streams are collided. (author)

0-d energetics scaling models for Z-pinch-driven hohlraums

International Nuclear Information System (INIS)

CUNEO, MICHAEL E.; VESEY, ROGER A.; HAMMER, J.H.; PORTER, JOHN L.

2000-01-01

Wire array Z-pinches on the Z accelerator provide the most intense laboratory source of soft x-rays in the world. The unique combination of a highly-Planckian radiation source with high x-ray production efficiency (15% wall plug), large x-ray powers and energies ( >150 TW, ge1 MJ in 7 ns), large characteristic hohlraum volumes (0.5 to >10 cm 3 ), and long pulse-lengths (5 to 20 ns) may make Z-pinches a good match to the requirements for driving high-yield scale ICF capsules with adequate radiation symmetry and margin. The Z-pinch driven hohlraum approach of Hammer and Porter [Phys.Plasmas, 6, 2129(1999)] may provide a conservative and robust solution to the requirements for high yield, and is currently being studied on the Z accelerator. This paper describes a multiple region, 0-d hohlraum energetic model for Z-pinch driven hohlraums in four configurations. The authors observe consistency between the models and the measured x-ray powers and hohlraum wall temperatures to within ±20% in flux, for the four configurations

PBFA Z: A 20-MA Z-pinch driver for plasma radiation sources

International Nuclear Information System (INIS)

Spielman, R.B.; Breeze, S.F.; Deeney, C.

1996-01-01

Sandia National Laboratories is completing a major modification to the PBFA-II facility. PBFA Z will be capable of delivering up to 20 MA to a z-pinch load. It optimizes the electrical coupling to the implosion energy of z pinches at implosion velocities of ∼ 40 cm/μs. Design constraints resulted in an accelerator with a 0.12-Ω impedance, a 10.25-nH inductance, and a 120-ns pulse width. The design required new water transmission lines, insulator stack, and vacuum power feeds. Current is delivered to the z-pinch load through four self-magnetically-insulated vacuum transmission lines and a double post-hole convolute. A variety of design codes are used to model the power flow. These predict a peak current of 20 MA to a z-pinch load having a 2-cm length, a 2-cm radius, and a 15-mg mass, coupling 1.5 MJ into kinetic energy. Calculations are presented showing MJ x-ray outputs from tungsten wire-array z pinches. (author). 4 figs., 14 refs

PBFA Z: A 20-MA Z-pinch driver for plasma radiation sources

Energy Technology Data Exchange (ETDEWEB)

Spielman, R B; Breeze, S F; Deeney, C [Sandia Labs., Albuquerque, NM (United States); and others

1997-12-31

Sandia National Laboratories is completing a major modification to the PBFA-II facility. PBFA Z will be capable of delivering up to 20 MA to a z-pinch load. It optimizes the electrical coupling to the implosion energy of z pinches at implosion velocities of {approx} 40 cm/{mu}s. Design constraints resulted in an accelerator with a 0.12-{Omega} impedance, a 10.25-nH inductance, and a 120-ns pulse width. The design required new water transmission lines, insulator stack, and vacuum power feeds. Current is delivered to the z-pinch load through four self-magnetically-insulated vacuum transmission lines and a double post-hole convolute. A variety of design codes are used to model the power flow. These predict a peak current of 20 MA to a z-pinch load having a 2-cm length, a 2-cm radius, and a 15-mg mass, coupling 1.5 MJ into kinetic energy. Calculations are presented showing MJ x-ray outputs from tungsten wire-array z pinches. (author). 4 figs., 14 refs.

''Turbulent Equipartition'' Theory of Toroidal Momentum Pinch

International Nuclear Information System (INIS)

Hahm, T.S.; Diamond, P.H.; Gurcan, O.D.; Rewaldt, G.

2008-01-01

The mode-independent part of magnetic curvature driven turbulent convective (TuroCo) pinch of the angular momentum density (Hahm et al., Phys. Plasmas 14,072302 (2007)) which was originally derived from the gyrokinetic equation, can be interpreted in terms of the turbulent equipartition (TEP) theory. It is shown that the previous results can be obtained from the local conservation of 'magnetically weighted angular momentum density', nm i U # parallel# R/B 2 , and its homogenization due to turbulent flows. It is also demonstrated that the magnetic curvature modification of the parallel acceleration in the nonlinear gyrokinetic equation in the laboratory frame, which was shown to be responsible for the TEP part of the TurCo pinch of angular momentum density in the previous work, is closely related to the Coriolis drift coupling to the perturbed electric field. In addition, the origin of the diffusive flux in the rotating frame is highlighted. Finally, it is illustrated that there should be a difference in scalings between the momentum pinch originated from inherently toroidal effects and that coming from other mechanisms which exist in a simpler geometry.

Conservation of fusion reaction optimum yield in focused discharges with variable voltage and energy but constant geometry

International Nuclear Information System (INIS)

Bilbao, L.; Bortolotti, A.; Brzosko, J.; DeChiara, P.; Kilic, H.; Mezzetti, F.; Nardi, V.; Powell, C.; Wang, J.

1992-01-01

The D-D fusion reaction yield per pulse, Y n , of focused discharges is monitored by changing the capacitor bank voltage Vo by a factor 2 without any change of construction parameters and of the filling gas pressure of two plasma focus machines PF1 (C1 congruent 50 microfarad, L1 congruent 20 nanohenry) and PF2 (C2 = 1.2Cl, L2 = 2L1). The interval Δ = 1 ± (ΔW)/W of the capacitor bank energy values W on which the scaling Y n ∼ W 2 applies is greater for PF2, where the corresponding variation ΔI2 of the peak electrode current I2 is smaller (in agreement with Lw/C2 > L1/C1) than for PF1. Suitable figure of merit (in terms of ΔI, ΔW, L, C, etc.) are used for determining the relative importance of (i), the induced variations of the pinch fine structure and of (ii), the variations of the insulator surface at the PF breech, with bearing on the initial stage of the current sheath formation. Schlieren and magnetic probe data monitor the current sheath structure and propagation speed. The D + ion emission from the pinch is monitored in the energy interval 50 keV to 25 MeV for clarifying the links between the pinch fine structure and the set of leading macroscopic parameters of the PF discharges

The belt pinch - a high-β tokamak with non-circular cross-section

International Nuclear Information System (INIS)

Gruber, O.; Peiry, J.M.; Wilhelm, R.

1975-10-01

The stability behaviour of non-circular plasma cross-sections is discussed on the basis of present known theory. Then the technical arrangement and the preionization of the Belt Pinch is described. The following section deals with the establishment of the non-circular equilibrium and summarizes the essential plasma paramters and the used diagnostic methods. The stability properties of the Belt Pinch, lead to a critical q-value. Finnaly, supporting experiments for the future Belt Pinch programm are presented. (orig./GG) [de

Simplified scaling model for the THETA-pinch

Science.gov (United States)

Ewing, K. J.; Thomson, D. B.

1982-02-01

A simple ID scaing model for the fast Theta pinch was developed and written as a code that would be flexible, inexpensive in computer time, and readily available for use with the Los Alamos explosive-driven high magnetic field program. The simplified model uses three successive separate stages: (1) a snowplow-like radial implosion, (2) an idealized resistive annihilation of reverse bias field, and (3) an adiabatic compression stage of a Beta = 1 plasma for which ideal pressure balance is assumed to hold. The code uses one adjustable fitting constant whose value was first determined by comparison with results from the Los Alamos Scylla III, Scyllacita, and Scylla IA Theta pinches.

Numerical investigations of Z-pinch plasma instabilities

International Nuclear Information System (INIS)

Duan Yaoyong; Guo Yonghui; Wang Wensheng; Qiu Aici

2004-01-01

A two-dimensional, radiation magneto-hydrodynamics model is applied to the simulation of Z-pinch plasma sausage instability. Different implosion mechanisms in the cases of the existence and the non-existence of instability are analyzed, and the effects of various initial density perturbation levels on the x-ray power and energy are investigated. Numerical results show that x-ray energy output is not susceptive to sausage instabilities in a certain extent but x-ray power versus time is evidently dependent on the instabilities. In addition, this paper also studies the effects of numerical treatment of extreme low density in Z-pinch simulations on numerical results

A tentative opinion of modeling plasma formation in metallic wire Z pinch

International Nuclear Information System (INIS)

Ding Ning

2002-01-01

Numerous experiments in both single wire and in wire arrays have attracted much attention. For the wire array Z-pinch implosions the plasma formation in the metallic wire Z pinches is a key question. By means of analyzing a number of single-wire and multi-wire experiments, two models to describe the behavior of a wire array Z-pinch in initial phase are suggested. In this phase each wire carries a rising current and behaves independently in a way similar to that found in single wire Z-pinch experiments in which a comparable current in one wire is employed. Based on one- or/and two-dimensional magnetohydrodynamics (MHD) theory, one model is used to simulate the electrical explosion stage of the metallic wire, another is used to simulate the wire-plasma formation stage

Study of the internal structure, instabilities, and magnetic fields in the dense Z-pinch

International Nuclear Information System (INIS)

Ivanov, Vladimir V.

2016-01-01

Z-pinches are sources of hot dense plasma which generates powerful x-ray bursts and can been applied to various areas of high-energy-density physics (HEDP). The 26-MA Z machine is at the forefront of many of these applications, but important aspects of HEDP have been studied on generators at the 1 MA current level. Recent development of laser diagnostics and upgrade of the Leopard laser at Nevada Terawatt Facility (NTF) give new opportunities for the dense Z-pinch study. The goal of this project is the investigation of the internal structure of the stagnated Z pinch including sub-mm and micron-scale instabilities, plasma dynamics, magnetic fields, and hot spots formation and initiation. New plasma diagnostics will be developed for this project. A 3D structure and instabilities of the pinch will be compared with 3D MHD and spectroscopic modeling and theoretical analysis. The structure and dynamics of stagnated Z pinches has been studied with x-ray self-radiation diagnostics which derive a temperature map of the pinch with a spatial resolution of 70-150 µm. The regular laser diagnostics at 532 nm does not penetrate in the dense pinch due to strong absorption and refraction in trailing plasma. Recent experiments at NTF showed that shadowgraphy at the UV wavelength of 266 nm unfolds a fine structure of the stagnated Z-pinch with unprecedented detail. We propose to develop laser UV diagnostics for Z pinches with a spatial resolution 20 MG, suggested in micropinches, Cotton-Mouton and cutoff diagnostics will be applied. A picosecond optical Kerr shutter will be tested to increase a sensitivity of UV methods for application at multi-MA Z pinches. The proposal is based on the experimental capability of NTF. The Zebra generator produces 1-1.7 MA Z-pinches with electron plasma density of 10"2"0-10"2"1cm"-"3, electron temperature of 0.5-1 keV, and magnetic fields >10 MG. The Leopard laser was upgraded to energy of 90-J at 0.8 ns. This regime will be used for laser initiation

The Z-pinch as plasma lens for the focusing of heavy ion beams

International Nuclear Information System (INIS)

Elfers, M.

1992-04-01

In the present thesis the influence of a Z-pinch plasma on the shape of heavy-ion beams and the for the understanding of this interaction most important plasma parameters were studied. For this the Z-pinch at the heavy-ion accelerator UNILAC was operated. The magnet field gradients of up to (25 ± 3) T/m occuring in the Z-pinch lead to the plasma-lens effect - the focusing of a charged-particle beam traversing axially the Z-pinch. In this thesis for the first time the focusing of a heavy-ion beam by the azimutal magnetic field of a Z-pinch is described. Different beams with an original diameter of 10 mm were focused. The smallest measured beam diameter amounts to 1 mm half-width. The beam energy amounts to 11.4 MeV/u, which leads at gold as projectile matter to a beam energy of 2.25 GeV. (orig./HSI) [de

Study of the internal structure, instabilities, and magnetic fields in the dense Z-pinch

Energy Technology Data Exchange (ETDEWEB)

Ivanov, Vladimir V. [Univ. of Nevada, Reno, NV (United States)

2016-08-17

Z-pinches are sources of hot dense plasma which generates powerful x-ray bursts and can been applied to various areas of high-energy-density physics (HEDP). The 26-MA Z machine is at the forefront of many of these applications, but important aspects of HEDP have been studied on generators at the 1 MA current level. Recent development of laser diagnostics and upgrade of the Leopard laser at Nevada Terawatt Facility (NTF) give new opportunities for the dense Z-pinch study. The goal of this project is the investigation of the internal structure of the stagnated Z pinch including sub-mm and micron-scale instabilities, plasma dynamics, magnetic fields, and hot spots formation and initiation. New plasma diagnostics will be developed for this project. A 3D structure and instabilities of the pinch will be compared with 3D MHD and spectroscopic modeling and theoretical analysis. The structure and dynamics of stagnated Z pinches has been studied with x-ray self-radiation diagnostics which derive a temperature map of the pinch with a spatial resolution of 70-150 µm. The regular laser diagnostics at 532 nm does not penetrate in the dense pinch due to strong absorption and refraction in trailing plasma. Recent experiments at NTF showed that shadowgraphy at the UV wavelength of 266 nm unfolds a fine structure of the stagnated Z-pinch with unprecedented detail. We propose to develop laser UV diagnostics for Z pinches with a spatial resolution <5 μm to study the small-scale plasma structures, implement two-frame shadowgraphy/interferometry, and develop methods for investigation of strong magnetic fields. New diagnostics will help to understand better basic physical processes in Z pinches. A 3D internal structure of the pinch and characteristic instabilities will be studied in wire arrays with different configurations and compared with 3D MHD simulations and analytical models. Mechanisms of “enhanced heating” of Z-pinch plasma will be studied. Fast dynamics of stagnated

Evolution of the MHD sheet pinch

International Nuclear Information System (INIS)

Matthaeus, W.H.; Montgomery, D.

1979-01-01

A magnetohydrodynamic (MHD) problem of recurrent interest for both astrophysical and laboratory plasmas is the evolution of the unstable sheet pinch, a current sheet across which a dc magnetic field reverses sign. The evolution of such a sheet pinch is followed with a spectral-method, incompressible, two-dimensional, MHD turbulence code. Spectral diagnostics are employed, as are contour plots of vector potential (magnetic field lines), electric current density, and velocity stream function (velocity streamlines). The nonlinear effect which seems most important is seen to be current filamentation: the concentration of the current density onto sets of small measure near a mgnetic X point. A great deal of turbulence is apparent in the current distribution, which, for high Reynolds numbers, requires large spatial grids (greater than or equal to (64) 2 ). 11 figures, 1 table

Discharge plasmas as EUV Sources for Future Micro Lithography

Science.gov (United States)

Kruecken, Thomas

2007-08-01

Future extreme ultraviolet (EUV) lithography will require very high radiation intensities in a narrow wavelength range around 13.5 nm, which is most efficiently emitted as line radiation by highly ionized heavy particles. Currently the most intense EUV sources are based on xenon or tin gas discharges. After having investigated the limits of a hollow cathode triggered xenon pinch discharge Philips Extreme UV favors a laser triggered tin vacuum spark discharge. Plasma and radiation properties of these highly transient discharges will be compared. Besides simple MHD-models the ADAS software package has been used to generate important atomic and spectral data of the relevant ion stages. To compute excitation and radiation properties, collisional radiative equilibria of individual ion stages are computed. For many lines opacity effects cannot be neglected. In the xenon discharges the optical depths allow for a treatment based on escape factors. Due to the rapid change of plasma parameters the abundancies of the different ionization stages must be computed dynamically. This requires effective ionization and recombination rates, which can also be supplied by ADAS. Due to very steep gradients (up to a couple orders of magnitude per mm) the plasma of tin vacuum spark discharges is very complicated. Therefore we shall describe here only some technological aspects of our tin EUV lamp: The electrode system consists of two rotating which are pulled through baths of molten tin such that a tin film remains on their surfaces. With a laser pulse some tin is ablated from one of the wheels and travels rapidly through vacuum towards the other rotating wheel. When the tin plasma reaches the other electrodes it ignites and the high current phase starts, i.e. the capacitor bank is unloaded, the plasma is pinched and EUV is radiated. Besides the good spectral properties of tin this concept has some other advantages: Erosion of electrodes is no severe problem as the tin film is

Nonlinear development of the sausage instability in dense Z-pinches

International Nuclear Information System (INIS)

Colombant, D.; Mosher, D.

1989-01-01

In this paper, a 2d envelope model is described for the nonlinear development of the sausage instability in dense Z-pinches. Numerical solutions for various cases of interest are provided which lay the foundation for a quantitative model of nonthermal neutron emission in dense Z-pinches by determining the induced electric fields associated with the development of the instability

Numerical studies of neon gas-puff Z-pinch dynamic processes

International Nuclear Information System (INIS)

Ning Cheng; Yang Zhenhua; Ding Ning

2003-01-01

Dynamic processes of neon gas-puff Z-pinch are studied numerically in this paper. A high temperature plasma with a high density can be generated in the process. Based on some physical analysis and assumption, a set of equations of one-dimensional Lagrangian radiation magneto-hydrodynamic (MHD) and its code are developed to solve the problem. Spatio-temporal distributions of plasma parameters in the processes are obtained, and their dynamic variations show that the major results are self-consistent. The duration for the plasma pinched to centre, as well as the width and the total energy of the x-ray pulse caused by the Z-pinch are in reasonable agreement with experimental results of GAMBLE-II. A zipping effect is also clearly shown in the simulation

Reversed-field-pinch and ultra-low-q discharges in REPUTE-2

International Nuclear Information System (INIS)

Inoue, N.; Yoshida, Z.; Kamada, Y.; Saito, M.; Miyamoto, K.

1987-01-01

Ultra-low q (ULQ) and very-low q (VLQ) discharge experiments have been done using the REPUTE-1 RFP. It was found that in these q regime, the plasma density and beta are fairly high, and the confinement property is less sensitive to the error field compared to the RFP. However, since the temperature of the REPUTE-1 discharge is limited in low value because of the small plasma current due to the small toroidal field, its magnetic Reynolds number is too small to simulate the reactor plasma behavior. The radiation barrier has not been overcome yet, and consequently the energy confinement time is very short. In order to improve these aspects of the REPUTE-1 experiment, the REPUTE-2 is designed to produce higher toroidal field of 2T. The toroidal field increases slowly to the final value as in the case of the ramp-up mode of the RFP operation. The first stage of the REPUTE-2 project will be devoted to study the confinement physics of RFP, ULQ, and VLQ. In the second stage, innovation of these configurations, such as resistive shell RFP, neutral beam current drive, and higher current density, is planned. 8 refs., 1 fig., 2 tabs

Multi-scale characterization of an upcurrent turbiditic pinch-out

Science.gov (United States)

Daghdevirenian, L. J. P.; Migeon, S.; Rubino, J. L., Sr.; Raisson, F.

2017-12-01

Continental margins with a steep topographic profile between their continental shelf and the basin exhibit a sudden slope break at the base of their continental slope. This slope break favors strong erosion or a by-pass and a fast accumulation of sediments on the base of the continental slope due to the hydraulic jump phenomena. Such a process is responsible for the construction of thick accumulations of limited extension and generally disconnected from the feeding tributaries. These accumulations usually onlap against the continental slope but their modality of pinch out is still questioned and it is the subject of this work. The Tabernas basin is located in South East of Spain, in the continuity of the Sorbas basin. Recent field works allowed identifying a "sedimentary" onlap associated with a small-scale sandy turbidite system that we discovered near the so-called El Buho area. The superb quality of the outcrops revealed, the presence of three successive onlap structures consisting in each case of a direct contact between fluvial conglomerates / marines conglomerates / marine marls / turbidite sands. Reconstruction of paleo-current direction gives a flow direction around N00, from north to south, suggesting the outcrops are cutting the pinch out of the sandy system in a longitudinal direction. A longitudinal and vertical transition of facies can be thus observed from marines' conglomerates to turbidite sands, respectively over distances of 500 m and 70 m. The complete evolution of facies along the pinch out consists of thick conglomerates in the proximal part to sandy turbidite channels then lobes in the distal part. The three successive onlap structures are located inside the channelize part of the system, just above a slope break structure. The basal units of the pinch out consist of an alternation of conglomerates and sandy bed, while the overlying units exhibits more sandy dominated beds. In order to reconstruct the architecture of the pinch out and to

Nonlinear tearing modes in the reversed field pinch

International Nuclear Information System (INIS)

Miller, G.

1989-01-01

Finite-amplitude islands, which are the saturated states of tearing modes in the reversed field pinch, are calculated. These states are bifurcated noncylindrical equilibrium states. With σ(r) (σequivalentj x B/B 2 ) nonuniform across the plasma, as is consistent with experiment, a variety of m = 1 and m = 0 bifurcated equilibria are possible, instead of just the m = 1 helix calculated for uniform σ(r) by Taylor [in Pulsed High Beta Plasmas, edited by D. Evans (Pergamon, Oxford, 1976), p. 59]. Assuming the magnetic field lines in the reversed field pinch are weakly stochastic, the growth time of an unstable tearing mode is on the inertial time scale, as in the Taylor model, in constrast to growth on the resistive time scale predicted from nonlinear tearing mode theory when magnetic surfaces exist. The dependence of the saturated island width on radius of a conducting shell is investigated. Islands in the reversed field pinch often have magnetic wells in the island interior, which may result in improved confinement in the island regions

Space and time resolved observations of plasma dynamics in a compressional gas embedded Z-pinch

International Nuclear Information System (INIS)

Soto, L.; Chuaqui, H.; Favre, M.; Saavedra, R.; Wyndham, E.; Aliaga-Rossel, R.; Mitchell, I.

1996-01-01

Recent experiments in a gas embedded compressional Z-pinch are presented. The experiments have been carried out in H 2 at 1/3 atm, using a pulse power generator capable of delivering a dl/dt > 10 12 A/s. The pinch is initiated by a focused laser pulse, which is coaxial with a cylindrical DC microdischarge. This configuration results in double column pinch at early times, which at current rise evolves into a gas embedded compressional Z-pinch. Diagnostics used are Rogowski coil, single frame holographic interferometry, and holographic shadowgraphy, visible streak camera images from which current, density, line density, pinch radius and plasma motion are obtained. The pinch is characterized by a maximum on axis density which is much higher than the expected value from the filling pressure, with a Bennett temperature of 40 eV at 130 kA. The results shown confirm the high degree of compression achievable with the composite preionization scheme. (author). 4 figs., 5 refs

Numerical simulation of a Z-pinch compressed by imploding liner

International Nuclear Information System (INIS)

Bilbao, L.; Linhart, J.G.; Verri, G.; Bernal, L.

2001-01-01

The spark created in a neck of a dense Z-pinch can ignite a fusion detonation in the adjacent D-T plasma channel. Using an appropriate transition between the ignited D-T plasma and an inertially confined cylinder of highly compressed advanced fuel plasma it is possible to amplify the spark energy to a level adequate for the ignition of a detonation wave in the advanced fuel. An m=0 instability of a Z-pinch carrying a current of the order of 10 MA, with a rise time inferior to 10 ns can generate a spark capable of igniting a fusion detonation in the adjacent D-T plasma channel. Such μZ-pinch may be produced by a fast implosion of a cylindrical liner, while a conical channel properly chosen can amplify the spark energy. In order to derive some general rules for the parameters of the spark, the transition, the cylinder of advanced fuel and the liner different numerical models were used. We present here a review of these results and an outline of a possible experimental arrangement for obtaining such a Z-pinch compression

Plasma performance and scaling laws in the RFX-mod reversed-field pinch experiment

International Nuclear Information System (INIS)

Innocente, P.; Alfier, A.; Canton, A.; Pasqualotto, R.

2009-01-01

The large range of plasma currents (I p = 0.2-1.6 MA) and feedback-controlled magnetic boundary conditions of the RFX-mod experiment make it well suited to performing scaling studies. The assessment of such scaling, in particular those on temperature and energy confinement, is crucial both for improving the operating reversed-field pinch (RFP) devices and for validating the RFP configuration as a candidate for the future fusion reactors. For such a purpose scaling laws for magnetic fluctuations, temperature and energy confinement have been evaluated in stationary operation. RFX-mod scaling laws have been compared with those obtained from other RFP devices and numerical simulations. The role of the magnetic boundary has been analysed, comparing discharges performed with different active control schemes of the edge radial magnetic field.

Pinch grafting for chronic venous leg ulcers in general practice

OpenAIRE

Steele, Keith

1985-01-01

Twenty-five patients with chronic venous leg ulcers were treated in general practice by pinch grafting. Fifteen of the ulcers (60%) were completely healed one year after grafting. Prior to grafting 19 patients (76%) complained of daily pain in the ulcer. These patients experienced complete relief from pain after grafting. Pinch grafting is a simple, safe and effective therapy when applied in a domiciliary environment.

Numerical simulation on the screw pinch by 2-D MHD pinch code 'topics' including impurities and neutrals effects

International Nuclear Information System (INIS)

Nagata, A.; Ashida, H.; Okamoto, M.; Hirano, K.

1981-03-01

Two dimentional fluid simulation code ''TOPICS'' is developed for the STP-2, the shock heated screw pinch at Nagoya. It involves the effects of impurity ions and neutral atoms. In order to estimate the radiation losses, the impurity continuity equations with ionizations and recombinations are solved simultaneously with the plasma fluid equations. The results are compared with the coronal equilibrium model. It is found that the coronal equilibrium model underestimates the radiation losses from shock heated pinch plasmas in its initial dynamic phase. The present calculations including impurities and neutrals show the importance of the radiation losses from the plasma of the STP-2. Introducing the anomalous resistivity caused by the ion acoustic instability, the observed magnetic field penetration is explained fairly well. (author)

Pinching evidences in a miniature plasma focus with fast pseudospark switch

International Nuclear Information System (INIS)

Hassan, S M; Zhang, T; Patran, A; Rawat, R S; Springham, S V; Tan, T L; Wong, D; Wang, W; Lee, S; Gribkov, V A; Mohanty, S R; Lee, P

2006-01-01

We report the observations of pinching in a miniature plasma focus (PF) (58-160 J) operated in repetitive mode using fast pseudospark switch (PSS). The size of the device, which includes the capacitor bank, PSS and the focus chamber, is of the order of 22 cm x 22 cm x 38 cm. Several diagnostic tools, the gated imager, streak camera, current and voltage probe, are employed simultaneously to confirm the occurrence of pinching in this fast miniature PF device. The device is optimized for operation in neon and hydrogen as the working gas. The best focus formation was obtained at pressures between 0.5 to 8.0 mbar for neon and between 7.0 to 15.0 mbar for hydrogen. When the system was operated at 100 J with hydrogen as the filling gas, the typical dip in the current derivative signal and the typical peak in the voltage signal associated with pinch compression, are observed to be most intense indicating efficient pinching in the miniature PF device

Studies of implosion processes of nested tungsten wire-array Z-pinch

International Nuclear Information System (INIS)

Ning Cheng; Ding Ning; Liu Quan; Yang Zhenhua

2006-01-01

Nested wire-array is a kind of promising structured-load because it can improve the quality of Z-pinch plasma and enhance the radiation power of X-ray source. Based on the zero-dimensional model, the assumption of wire-array collision, and the criterion of optimized load (maximal load kinetic energy), optimization of the typical nested wire-array as a load of Z machine at Sandia Laboratory was carried out. It was shown that the load has been basically optimized. The Z-pinch process of the typical load was numerically studied by means of one-dimensional three-temperature radiation magneto-hydrodynamics (RMHD) code. The obtained results reproduce the dynamic process of the Z-pinch and show the implosion trajectory of nested wire-array and the transfer process of drive current between the inner and outer array. The experimental and computational X-ray pulse was compared, and it was suggested that the assumption of wire-array collision was reasonable in nested wire-array Z-pinch at least for the current level of Z machine. (authors)

Experimental studies of Z-pinches of mixed wire array with aluminum and tungsten

International Nuclear Information System (INIS)

Ning Cheng; Li Zhenghong; Hua Xinsheng; Xu Rongkun; Peng Xianjue; Xu Zeping; Yang Jianlun; Guo Cun; Jiang Shilun; Feng Shuping; Yang Libing; Yan Chengli; Song Fengjun; Smirnov, V.P.; Kalinin, Yu.G.; Kingsep, A.S.; Chernenko, A.S.; Grabovsky, E.V.

2004-01-01

In the form of joint experiment between China and Russia, the experimental studies of Z-pinches of mixed wire array of aluminum (A1) and tungsten (W) were carried out on S-300 generator, which was located on Kurchatov Institute of Russia. The experimental results were compared with those of single A1 array and single W array, respectively. There are obvious difference between mixed one and single one in their photon spectral distributions. The intensity of K-series emission lines from the mixed wire array Z-pinch is lower than that from single A1 array. The radiated lines with wavelengths less than 1.6 nm were not found in single W array Z-pinches. In the Z-pinch processes, the area radiating x-rays in mixed wire array is smaller than that of single A1 array, but is slightly lower than that from single W array. The FWHM of x-ray pulse with a maximal power 0.3-0.5 TW and total energy 10-20 kJ is about 25 ns, which radiated from Z-pinches with a radial convergence of 4-5 on S-300 generator. The shadow photograph of the mixed wire-array Z-pinch plasma by laser probe shows that the core-corona configuration was formed and the corona was moving toward the center axis during the wire-array plasma formation, that the interface of the plasma is not clear, and that there are a number structures inside. They also suggests that there was an obvious development of Magneto Rayleigh-Taylor instability in the Z-pinch process as well

Current, temperature and confinement time scaling in toroidal reversed-field pinch experiments ZT-I and ZT-S

International Nuclear Information System (INIS)

Baker, D.A.; Burkhardt, L.C.; Di Marco, J.N.; Haberstich, A.; Hagenson, R.L.; Howell, R.B.; Karr, H.J.; Schofield, A.E.

1977-01-01

The scaling properties of a toroidal reversed-field Z pinch have been investigated over a limited range by comparing two experiments having conducting walls and discharge-tube minor diameters which differ by a factor of approximately 1.5. Both the confinement time of the plasma column and the electron temperature were found to increase about a factor of two with the increased minor diameter. Both the poloidal field diffusion and the decay of the toroidal reversed field were significantly reduced with the larger tube diameter. These results support the hypothesis that the loss of stability later in the discharge is caused by diffusion-induced deterioration of initially favourable plasma-field profiles to MHD unstable ones. This conclusion has been verified by stability analysis of the magnetic field profiles. Fusion reactor calculations show that small reactors are conceptually possible assuming good containment can be achieved for current densities approximately >20MAm -2 . (author)

Implosion heating studies in the Scylla 1B, implosion heating, and staged theta-pinch experiments

International Nuclear Information System (INIS)

Gribble, R.F.; Hammel, J.E.; Henins, I.; Jahoda, F.C.; Kristal, R.; Linford, R.K.; Marshall, J.; McKenna, K.F.; Sherwood, A.R.; Thomas, K.S.

1975-01-01

Three experiments designed to study various aspects of implosion heating in the plasma density range (10 14 -10 16 cm -3 ) used in present theta pinches are described. Initial plasma studies show that, provided a sufficiently high pre-ionization level (>10 14 cm -3 ) is achieved, plasma behaviour is qualitatively the same over a range of two in initial magnetic field rise and a range of four in initial gas fill. The implosion phase is characterized by rapid changes in magnetic-field diffusion rates, the plasma resistivity decreasing rapidly with time. During the implosion some of the plasma density observed is moving ahead of the magnetic piston. Magnetic-field gradients occur in the region outside the area of measurable plasma density implying the presence of hot, low-density plasma in this region. In experiments where the external magnetic field decreases before the maximum compression of the plasma column, secondary breakdown occurs at the discharge tube wall which slows the rate at which magnetic flux diffuses out of the discharge tube. (author)

The design and implementation of a windowing interface pinch force measurement system

Science.gov (United States)

Ho, Tze-Yee; Chen, Yuanu-Joan; Chung, Chin-Teng; Hsiao, Ming-Heng

2010-02-01

This paper presents a novel windowing interface pinch force measurement system that is basically based on an USB (Universal Series Bus) microcontroller which mainly processes the sensing data from the force sensing resistance sensors mounted on five digits. It possesses several friendly functions, such as the value and curve trace of the applied force by a hand injured patient displayed in real time on a monitoring screen, consequently, not only the physician can easily evaluate the effect of hand injury rehabilitation, but also the patients get more progressive during the hand physical therapy by interacting with the screen of pinch force measurement. In order to facilitate the pinch force measurement system and make it friendly, the detail hardware design and software programming flowchart are described in this paper. Through a series of carefully and detailed experimental tests, first of all, the relationship between the applying force and the FSR sensors are measured and verified. Later, the different type of pinch force measurements are verified by the oscilloscope and compared with the corresponding values and waveform traces in the window interface display panel to obtain the consistency. Finally, a windowing interface pinch force measurement system based on the USB microcontroller is implemented and demonstrated. The experimental results show the verification and feasibility of the designed system.

Magnetic field compression using pinch-plasma

International Nuclear Information System (INIS)

Koyama, K.; Tanimoto, M.; Matsumoto, Y.; Veno, I.

1987-01-01

In a previous report, the method for ultra-high magnetic field compression by using the pinchplasma was discussed. It is summarized as follows. The experiment is performed with the Mather-type plasma focus device tau/sub 1/4/ = 2 μs, I=880 kA at V=20 kV). An initial DC magnetic field is fed by an electromagnet embedded in the inner electrode. The axial component of the magnetic field diverges from the maximum field of 1 kG on the surface of the inner electrode. The density profile deduced from a Mach-Zehnder interferogram with a 2-ns N/sub 2/-laser shows a density dip lasting for 30 ns along the axes. Using the measured density of 8 x 10/sup 18/ cm/sup -3/, the temperature of 1.5 keV and the pressure balance relation, the magnitude of the trapped magnetic field is estimated to be 1.0 MG. The magnitude of the compressed magnetic field is also measured by Faraday rotation in a single-mode quartz fiber and a magnetic pickup soil. A protective polyethylene tube (3-mm o.d.) is used along the central axis through the inner electrode and the discharge chamber. The peak value of the compressed field range from 150 to 190 kG. No signal of the magnetic field appears up to the instance of the maximum pinch

Recyclable transmission line (RTL) and linear transformer driver (LTD) development for Z-pinch inertial fusion energy (Z-IFE) and high yield

International Nuclear Information System (INIS)

Sharpe, Robin Arthur; Kingsep, Alexander S.; Smith, David Lewis; Olson, Craig Lee; Ottinger, Paul F.; Schumer, Joseph Wade; Welch, Dale Robert; Kim, Alexander; Kulcinski, Gerald L.; Kammer, Daniel C.; Rose, David Vincent; Nedoseev, Sergei L.; Pointon, Timothy David; Smirnov, Valentin P.; Turgeon, Matthew C.; Kalinin, Yuri G.; Bruner, Nichelle

2007-01-01

Z-Pinch Inertial Fusion Energy (Z-IFE) complements and extends the single-shot z-pinch fusion program on Z to a repetitive, high-yield, power plant scenario that can be used for the production of electricity, transmutation of nuclear waste, and hydrogen production, all with no CO 2 production and no long-lived radioactive nuclear waste. The Z-IFE concept uses a Linear Transformer Driver (LTD) accelerator, and a Recyclable Transmission Line (RTL) to connect the LTD driver to a high-yield fusion target inside a thick-liquid-wall power plant chamber. Results of RTL and LTD research are reported here, that include: (1) The key physics issues for RTLs involve the power flow at the high linear current densities that occur near the target (up to 5 MA/cm). These issues include surface heating, melting, ablation, plasma formation, electron flow, magnetic insulation, conductivity changes, magnetic field diffusion changes, possible ion flow, and RTL mass motion. These issues are studied theoretically, computationally (with the ALEGRA and LSP codes), and will work at 5 MA/cm or higher, with anode-cathode gaps as small as 2 mm. (2) An RTL misalignment sensitivity study has been performed using a 3D circuit model. Results show very small load current variations for significant RTL misalignments. (3) The key structural issues for RTLs involve optimizing the RTL strength (varying shape, ribs, etc.) while minimizing the RTL mass. Optimization studies show RTL mass reductions by factors of three or more. (4) Fabrication and pressure testing of Z-PoP (Proof-of-Principle) size RTLs are successfully reported here. (5) Modeling of the effect of initial RTL imperfections on the buckling pressure has been performed. Results show that the curved RTL offers a much greater buckling pressure as well as less sensitivity to imperfections than three other RTL designs. (6) Repetitive operation of a 0.5 MA, 100 kV, 100 ns, LTD cavity with gas purging between shots and automated operation is

Recyclable transmission line (RTL) and linear transformer driver (LTD) development for Z-pinch inertial fusion energy (Z-IFE) and high yield.

Energy Technology Data Exchange (ETDEWEB)

Sharpe, Robin Arthur; Kingsep, Alexander S. (Kurchatov Institute, Moscow, Russia); Smith, David Lewis; Olson, Craig Lee; Ottinger, Paul F. (Naval Research Laboratory, Washington, DC); Schumer, Joseph Wade (Naval Research Laboratory, Washington, DC); Welch, Dale Robert (Voss Scientific, Albuquerque, NM); Kim, Alexander (High Currents Institute, Tomsk, Russia); Kulcinski, Gerald L. (University of Wisconsin, Madison, WI); Kammer, Daniel C. (University of Wisconsin, Madison, WI); Rose, David Vincent (Voss Scientific, Albuquerque, NM); Nedoseev, Sergei L. (Kurchatov Institute, Moscow, Russia); Pointon, Timothy David; Smirnov, Valentin P. (Kurchatov Institute, Moscow, Russia); Turgeon, Matthew C.; Kalinin, Yuri G. (Kurchatov Institute, Moscow, Russia); Bruner, Nichelle " Nicki" (Voss Scientific, Albuquerque, NM); Barkey, Mark E. (University of Alabama, Tuscaloosa, AL); Guthrie, Michael (University of Wisconsin, Madison, WI); Thoma, Carsten (Voss Scientific, Albuquerque, NM); Genoni, Tom C. (Voss Scientific, Albuquerque, NM); Langston, William L.; Fowler, William E.; Mazarakis, Michael Gerrassimos

2007-01-01

Z-Pinch Inertial Fusion Energy (Z-IFE) complements and extends the single-shot z-pinch fusion program on Z to a repetitive, high-yield, power plant scenario that can be used for the production of electricity, transmutation of nuclear waste, and hydrogen production, all with no CO{sub 2} production and no long-lived radioactive nuclear waste. The Z-IFE concept uses a Linear Transformer Driver (LTD) accelerator, and a Recyclable Transmission Line (RTL) to connect the LTD driver to a high-yield fusion target inside a thick-liquid-wall power plant chamber. Results of RTL and LTD research are reported here, that include: (1) The key physics issues for RTLs involve the power flow at the high linear current densities that occur near the target (up to 5 MA/cm). These issues include surface heating, melting, ablation, plasma formation, electron flow, magnetic insulation, conductivity changes, magnetic field diffusion changes, possible ion flow, and RTL mass motion. These issues are studied theoretically, computationally (with the ALEGRA and LSP codes), and will work at 5 MA/cm or higher, with anode-cathode gaps as small as 2 mm. (2) An RTL misalignment sensitivity study has been performed using a 3D circuit model. Results show very small load current variations for significant RTL misalignments. (3) The key structural issues for RTLs involve optimizing the RTL strength (varying shape, ribs, etc.) while minimizing the RTL mass. Optimization studies show RTL mass reductions by factors of three or more. (4) Fabrication and pressure testing of Z-PoP (Proof-of-Principle) size RTLs are successfully reported here. (5) Modeling of the effect of initial RTL imperfections on the buckling pressure has been performed. Results show that the curved RTL offers a much greater buckling pressure as well as less sensitivity to imperfections than three other RTL designs. (6) Repetitive operation of a 0.5 MA, 100 kV, 100 ns, LTD cavity with gas purging between shots and automated operation is

Self-Organization Observed in Numerical Simulations of a Hard-Core Diffuse Z Pinch

International Nuclear Information System (INIS)

Makhin, V; Siemon, R E; Bauer, B S; Esaulov, A; Lindemuth, I R; Ryutov, D D; Sheehey, P T; Sotnikov, V I

2005-04-01

The evolution of an unstable plasma profile into a stable profile, which we term self-organization, appears to be a robust process. Although it was not termed self organization, the same effect has been noted in past simulations with the same code. The result has been made easier to discern by the introduction of z-averaged profiles. A recent report of PIC simulations in the hard-core z-pinch configuration also shows self-organization. Figures 3 and 4 in Reference 21 show how pressure profiles in a low-β PIC simulation relax from unstable to stable. The non-linear evolution of the interchange motion has been studied under controlled initial conditions that result in exponential growth of a mode with a prescribed axial wavelength. An interesting feature of such growth is an abrupt transition from coherent to incoherent motion, after which the z-averaged pressure, current, and temperature profiles become quasi stationary. According to our understanding of MAGO experiments, the observed plasma behavior is consistent with the expectation of self-organization, but the diagnostics are not sufficiently detailed thus far to make a definite conclusion. The results of this simulations reported in this paper add motivation to planned experiments on an inverse pinch at UNR

Studies of a poloidal divertor reversed field pinch

International Nuclear Information System (INIS)

Sarff, J.S.; Almagri, A.F.; Assadi, S.; Den Hartog, D.J.; Dexter, R.N.; Prager, S.C.; Sprott, J.C.

1988-07-01

An attempt has been made to form a reversed field pinch (RFP) in a poloidal divertor configuration which position the plasma far from a conducting wall. In this configuration, the plasma is localized within a magnetic separatrix formed by the combination of toroidal currents in the plasma and four internal aluminum rings. Plasmas were formed with plasma current /approximately/135 kA, toroidal field reversal lasting /approximately/1 msec, line-averaged density /approximately/1--2 /times/ 10 13 cm/sup /minus/3/ and central electron temperature /approximately/55 eV, but a large asymmetry in the magnetic field (δB/B /approximately/40%) onset at about the time the toroidal field reversed at the wall. Symmetric, poloidal divertor RFP equilibria were not formed. This behavior might be expected based on linear MHD stability analysis of a cylindrical plasma bounded by a large vacuum region and distant conducting wall. The symmetric equilibrium before the asymmetry develops and the asymmetry itself are described. 15 refs., 3 figs

Seeded perturbations in wire array z-pinches

International Nuclear Information System (INIS)

Robinson, Allen Conrad; Kantsyrev, Victor Leonidovich; Wunsch, Scott Edward; Oliver, Bryan Velten; Lebedev, Sergey V.; Safronova, Alla S.; Maxwell, J.; McKenney, John Lee; Ampleford, David J.; Rapley, J.; Bott, S.C.; Palmer, J.B.A.; Bland, Simon Nicholas; Jones, Brent Manley; Chittenden, Jeremy Paul; Garasi, Christopher Joseph; Hall, Gareth Neville; Mehlhorn, Thomas Alan; Deeney, Christopher

2004-01-01

The impact of 3D structure on wire array z-pinch dynamics is a topic of current interest, and has been studied by the controlled seeding of wire perturbations. First, Al wires were etched at Sandia, creating 20% radial perturbations with variable axial wavelength. Observations of magnetic bubble formation in the etched regions during experiments on the MAGPIE accelerator are discussed and compared to 3D MHD modeling. Second, thin NaF coatings of 1 mm axial extent were deposited on Al wires and fielded on the Zebra accelerator. Little or no axial transport of the NaF spectroscopic dopant was observed in spatially resolved K-shell spectra, which places constraints on particle diffusivity in dense z-pinch plasmas. Finally, technology development for seeding perturbations is discussed

Magnetic islands at the field reversal surface in reversed field pinches

International Nuclear Information System (INIS)

Pinsker, R.I.; Reiman, A.H.

1985-09-01

In the reversed field pinch (RFP), magnetic field perturbations having zero poloidal mode number and any toroidal mode number are resonant at the field reversal surface. Such perturbations are a particular threat to the RFP because of their weak radial dependence at low toroidal mode number, and because the toroidal field ripple is essentially of this type. The widths of the resulting islands are calculated in this paper. The self-consistent plasma response is included through the assumption that the plasma relaxes to a Taylor force-free state. The connection with linear tearing mode theory is established for those limits where arbitrarily large islands result from infinitesimal perturbations. Toroidal effects are considered, and application of the theory to RFP experiments is discussed

Anomalous diffusion, clustering, and pinch of impurities in plasma edge turbulence

DEFF Research Database (Denmark)

Priego, M.; Garcia, O.E.; Naulin, V.

2005-01-01

The turbulent transport of impurity particles in plasma edge turbulence is investigated. The impurities are modeled as a passive fluid advected by the electric and polarization drifts, while the ambient plasma turbulence is modeled using the two-dimensional Hasegawa-Wakatani paradigm for resistive...... drift-wave turbulence. The features of the turbulent transport of impurities are investigated by numerical simulations using a novel code that applies semi-Lagrangian pseudospectral schemes. The diffusive character of the turbulent transport of ideal impurities is demonstrated by relative...... orientation determined by the charge of the impurity particles. Second, a radial pinch scaling linearly with the mass-charge ratio of the impurities is discovered. Theoretical explanation for these observations is obtained by analysis of the model equations. (C) 2005 American Institute of Physics....

Soft X-Ray Measurements of Z-Pinch-Driven Vacuum Hohlraums

International Nuclear Information System (INIS)

Baker, K.L.; Porter, J.L.; Ruggles, L.E.; Chandler, G.A.; Deeney, Chris; Varas, M.; Moats, Ann; Struve, Ken; Torres, J.; McGurn, J.; Simpson, W.W.; Fehl, D.L.; Chrien, R.E.; Matuska, W.; Idzorek, G.C.

1999-01-01

This article reports the experimental characterization of a z-pinch driven-vacuum hohlraum. The authors have measured soft x-ray fluxes of 5 x 10 12 W/cm 2 radiating from the walls of hohlraums which are 2.4--2.5 cm in diameter by 1 cm tall. The x-ray source used to drive these hohlraums was a z-pinch consisting of a 300 wire tungsten array driven by a 2 MA, 100 ns current pulse. In this hohlraum geometry, the z-pinch x-ray source can produce energies in excess of 800 kJ and powers in excess of 100 TW to drive these hohlraums. The x-rays released in these hohlraums represent greater than a factor of 25 in energy and more than a factor of three in x-ray power over previous laboratory-driven hohlraums

Study of the noncylindrical Z-pinch during discharges in neon using electro-optical transducer of the AGAT type

International Nuclear Information System (INIS)

Lebedev, V.B.; Orlov, M.M.; Saulevich, S.V.; Terent'ev, A.R.; Khrabrov, V.A.

1986-01-01

Results of investigation into running away current-plasma sheath (CPS) of noncylindrical Z-pinch are given. Experimental chamber was filled with neon up to 3 torr pressure. Store of energy was equal to 20 kJ. CPS radiation spectrum scanning was recorded in the phase of its convergence to the system axis by means of an electron-optical converter of the AGAT type. Electron temperature in the inflection region on CPS constituted 3 eV. Possibilities of magnetic field diffusion through neon CPS and appearance of CPS running away mode are shown. CPS plasma spectra indicated that radiation can be recorded only from a CPS head near-anode part and its external peripheral regions moving from the axis and emitting considerably less quantity of radiation

Plasma confinement of Nagoya high-beta toroidal-pinch experiments

International Nuclear Information System (INIS)

Hirano, K.; Kitagawa, S.; Wakatani, M.; Kita, Y.; Yamada, S.; Yamaguchi, S.; Sato, K.; Aizawa, T.; Osanai, Y.; Noda, N.

1977-01-01

Two different types of high-β toroidal pinch experiments, STP [1] and CCT [2,3], have been done to study the confinement of the plasma produced by a theta-pinch. The STP is an axisymmetric toroidal pinch of high-β tokamak type, while the CCT consists of multiply connected periodic toroidal traps. Internal current-carrying copper rings are essential to the CCT. Since both apparatuses use the same fast capacitor bank system, they produce rather similar plasma temperatures and densities. The observed laser scattering temperature and density is about 50 eV and 4x10 15 cm -3 , respectively, when the filling pressure is 5 mtorr. In the STP experiment, strong correlations are found between the βsub(p) value and the amplitude of m=2 mode. It has a minimum around the value of βsub(p) of 0.8. The disruptive instability is observed to expand the pinched plasma column without lowering the plasma temperature. Just before the disruption begins, the q value around the magnetic axis becomes far less than 1 and an increase of the amplitude of m=2 mode is seen. The CCT also shows rapid plasma expansion just before the magnetic field reaches its maximum. Then the trap is filled up with the plasma by this irreversible expansion and stable plasma confinement is achieved. The energy confinement time of the CCT is found to be about 35 μs. (author)

Pinch analysis for bioethanol production process from lignocellulosic biomass

International Nuclear Information System (INIS)

Fujimoto, S.; Yanagida, T.; Nakaiwa, M.; Tatsumi, H.; Minowa, T.

2011-01-01

Bioethanol produced from carbon neutral and renewable biomass resources is an attractive process for the mitigation of greenhouse gases from vehicle exhaust. This study investigated energy utilization during bioethanol production from lignocellulose while avoiding competition with food production from corn and considering the potential mitigation of greenhouse gases. Process design and simulations were performed for bioethanol production using concentrated sulfuric acid. Mass and heat balances were obtained by process simulations, and the heat recovery ratio was determined by pinch analysis. An energy saving of 38% was achieved. However, energy supply and demand were not effectively utilized in the temperature range from 95 to 100 o C. Therefore, a heat pump was used to improve the temperature range of efficient energy supply and demand. Results showed that the energy required for the process could be supplied by heat released during the process. Additionally, the power required was supplied by surplus power generated during the process. Thus, pinch analysis was used to improve the energy efficiency of the process. - Highlights: → Effective energy utilization of bioethanol production was studied by using pinch analysis. → It was found that energy was not effectively utilized in the temperature range from 95 to 100 o C. → Use of a heat pump was considered to improve the ineffective utilization. → Then, remarkable energy savings could be achieved by it. → Pinch analysis effectively improved the energy efficiency of the bioethanol production.

Two-dimensional integrated Z-pinch ICF design simulations

International Nuclear Information System (INIS)

Lash, J.S.

1999-01-01

The dynamic hohlraum ICF concept for a Z-pinch driver utilizes the imploding wire array collision with a target to produce a radiation history suitable for driving an embedded inertial confinement fusion (ICF) capsule. This target may consist of various shaped layers of low-density foams or solid-density materials. The use of detailed radiation magneto-hydrodynamic (RMHD) modeling is required for understanding and designing these complex systems. Critical to producing credible simulations and designs is inclusion of the Rayleigh-Taylor unstable wire-array dynamics; the bubble and spike structure of the collapsing sheath may yield regions of low-opacity enhancing radiation loss as well as introduce non-uniformities in the capsule's radiation drive. Recent improvements in LASNEX have allowed significant progress to be made in the modeling of unstable z-pinch implosions. Combining this with the proven ICF capsule design capabilities of LASNEX, the authors now have the modeling tools to produce credible, fully-integrated ICF dynamic hohlraum simulations. They present detailed two-dimensional RMHD simulations of recent ICF dynamic hohlraum experiments on the Sandia Z-machine as well as design simulations for the next-generation Z-pinch facility and future high-yield facility

Two-dimensional integrated Z-pinch ICF design simulations

Energy Technology Data Exchange (ETDEWEB)

Lash, J.S.

1999-07-01

The dynamic hohlraum ICF concept for a Z-pinch driver utilizes the imploding wire array collision with a target to produce a radiation history suitable for driving an embedded inertial confinement fusion (ICF) capsule. This target may consist of various shaped layers of low-density foams or solid-density materials. The use of detailed radiation magneto-hydrodynamic (RMHD) modeling is required for understanding and designing these complex systems. Critical to producing credible simulations and designs is inclusion of the Rayleigh-Taylor unstable wire-array dynamics; the bubble and spike structure of the collapsing sheath may yield regions of low-opacity enhancing radiation loss as well as introduce non-uniformities in the capsule's radiation drive. Recent improvements in LASNEX have allowed significant progress to be made in the modeling of unstable z-pinch implosions. Combining this with the proven ICF capsule design capabilities of LASNEX, the authors now have the modeling tools to produce credible, fully-integrated ICF dynamic hohlraum simulations. They present detailed two-dimensional RMHD simulations of recent ICF dynamic hohlraum experiments on the Sandia Z-machine as well as design simulations for the next-generation Z-pinch facility and future high-yield facility.

Development and characterization of a Z-pinch-driven hohlraum high-yield inertial confinement fusion target concept

International Nuclear Information System (INIS)

Cuneo, Michael E.; Vesey, Roger A.; Porter, John L. Jr.; Chandler, Gordon A.; Fehl, David L.; Gilliland, Terrance L.; Hanson, David L.; McGurn, John S.; Reynolds, Paul G.; Ruggles, Laurence E.; Seamen, Hans; Spielman, Rick B.; Struve, Ken W.; Stygar, William A.; Simpson, Walter W.; Torres, Jose A.; Wenger, David F.; Hammer, James H.; Rambo, Peter W.; Peterson, Darrell L.

2001-01-01

Initial experiments to study the Z-pinch-driven hohlraum high-yield inertial confinement fusion (ICF) concept of Hammer, Tabak, and Porter [Hammer et al., Phys. Plasmas 6, 2129 (1999)] are described. The relationship between measured pinch power, hohlraum temperature, and secondary hohlraum coupling ('hohlraum energetics') is well understood from zero-dimensional semianalytic, and two-dimensional view factor and radiation magnetohydrodynamics models. These experiments have shown the highest x-ray powers coupled to any Z-pinch-driven secondary hohlraum (26±5 TW), indicating the concept could scale to fusion yields of >200 MJ. A novel, single-sided power feed, double-pinch driven secondary that meets the pinch simultaneity requirements for polar radiation symmetry has also been developed. This source will permit investigation of the pinch power balance and hohlraum geometry requirements for ICF relevant secondary radiation symmetry, leading to a capsule implosion capability on the Z accelerator [Spielman et al., Phys. Plasmas 5, 2105 (1998)

The belt-shaped screw-pinch reactor

International Nuclear Information System (INIS)

Bustraan, M.; Klippel, H.Th.; Veringa, H.J.; Verschuur, K.A.; Lievense, K.

1981-12-01

The belt-shaped screw pinch is a pulsed toroidal plasma with an elongated cross-section. Force-free currents in an outer plasma envelope of low density allow beta to rise to high values in the order of 50%. This is a potential possibility to develop an economically attractive reactor. The physical requirements of its realization are described: formation, heating and ignition of a very small amount of the fuel to be burnt in one pulse by the fields generated by normal or superconducting coils. Then follows injection of the greater part of the fuel by D-T pellets and consequent plasma heating and expansion by nuclear reactions without undue disturbing of the plasma current configuration. Technical requirements include an insulating first wall and fast rising magnetic fields produced by superconducting coils. This reactor system is compared with the tokamak and the reversed-field pinch system

MHD turbulence models for the reversed field pinch

International Nuclear Information System (INIS)

Gimblett, C.G.; Watkins, M.L.

1976-01-01

A kinematic model which describes the effect of isotropic, non-mirror symmetric turbulence on a mean magnetic field is used to examine the temporal behaviour of magnetic field in high beta pinch experiments. Solutions to the model can indicate the formation of a steady-state, force-free configuration that corresponds to the state of lowest magnetic energy and the reversal of the toroidal magnetic field at the plasma boundary in accordance with experimental observations on toroidal pinches such as ZETA and HBTX. This model neglects both the dynamic interaction between fluid and field and the associated anisotropy. These effects are examined in a further model. (author)

Pinched hysteresis behavior in a PID-controlled resistor

Directory of Open Access Journals (Sweden)

M.A. Carrasco-Aguilar

2018-06-01

Full Text Available A current-controlled grounded resistor that exhibits a frequency-dependent pinched hysteresis loop is described. A mathematical model describing this behavior is derived and validated numerically, which has the form of a Proportional Integral-Derivative (PID controller. The proposed topology is build by using AD844 commercially available active device configured as second-generation current conveyor and experimental tests are compared with numerical simulations, showing a good agreement among them. Moreover, the proposed PID-controlled resistor can be reconfigured in order to be used in future applications such as programmable analog circuits. Keyword: Pinched hysteresis, Current conveyors, Nonlinear resistor, Proportional-Integral-Derivative Controller

Review of effects of dielectric coatings on electrical exploding wires and Z pinches

Science.gov (United States)

Wu, Jian; Li, Xingwen; Li, Mo; Li, Yang; Qiu, Aici

2017-10-01

As the most powerful x-ray source in the laboratories, the wire array Z pinches have been of great relevance to inertial confinement fusions, laboratory astrophysics, and other high-energy density applications. In order to produce x-ray with greater power and higher efficiency, the dynamics of wire array has been investigated extensively, and various methods have been proposed to improve the implosion quality of the wire array. This review focuses on the experimental and theoretical investigations regarding the effects of the dielectric coatings on electrical exploding wires and Z pinches. Since the early 2000, the electrical wire explosion related to the first stage of the wire array Z pinches has been studied extensively, and the results indicated that the dielectric coatings can significantly increase the joule energy deposition into a wire in the initial stage, and even the corona free explosion of tungsten wires can be achieved. Recently, there is an increasing interest in the dynamics of insulated wire array Z pinches. By applying dielectric coatings, the ablation process is suppressed, the x-ray start time is delayed, and the possibility of multi-peak radiation is decreased. This review is organized by the evolution dynamics of wire array Z pinches, and a broad introduction to relevant scientific concepts and various other applications are presented. According to the current research status, the challenges, opportunities and further developments of Z pinch loads using dielectric coatings are proposed to further promote the researches and their applications.

Review of effects of dielectric coatings on electrical exploding wires and Z pinches

International Nuclear Information System (INIS)

Wu, Jian; Li, Mo; Li, Yang; Li, Xingwen; Qiu, Aici

2017-01-01

As the most powerful x-ray source in the laboratories, the wire array Z pinches have been of great relevance to inertial confinement fusions, laboratory astrophysics, and other high-energy density applications. In order to produce x-ray with greater power and higher efficiency, the dynamics of wire array has been investigated extensively, and various methods have been proposed to improve the implosion quality of the wire array. This review focuses on the experimental and theoretical investigations regarding the effects of the dielectric coatings on electrical exploding wires and Z pinches. Since the early 2000, the electrical wire explosion related to the first stage of the wire array Z pinches has been studied extensively, and the results indicated that the dielectric coatings can significantly increase the joule energy deposition into a wire in the initial stage, and even the corona free explosion of tungsten wires can be achieved. Recently, there is an increasing interest in the dynamics of insulated wire array Z pinches. By applying dielectric coatings, the ablation process is suppressed, the x-ray start time is delayed, and the possibility of multi-peak radiation is decreased. This review is organized by the evolution dynamics of wire array Z pinches, and a broad introduction to relevant scientific concepts and various other applications are presented. According to the current research status, the challenges, opportunities and further developments of Z pinch loads using dielectric coatings are proposed to further promote the researches and their applications. (topical review)

Computer modeling of a small neon gas-puff pinch

International Nuclear Information System (INIS)

Ullschmied, J.

1996-01-01

The macroscopic dynamics of a cylindrical gas-puff pinch and conditions of radiation plasma collapse are studied by using a one-dimensional ('mechanical') computer model. Besides the Joule plasma heating, compressional heating, magnetic field freezing in a plasma and recombination losses, also the real temperature- and density-dependences of radiation plasma loss are taken into account. The results of calculations are compared with experimental data taken from a small neon-puff z-pinch experiment operated at the Institute of Plasma Physics in Prague. (author). 7 figs., 11 refs

Experimental study of CF4 conical theta pinch plasma expanding into vacuum

International Nuclear Information System (INIS)

Pedrow, P.D.; Nasiruddin, A.M.

1989-01-01

Langmuir probe, photodiode, and optical multichannel analyzer (OMA) measurements have been made on a pulsed CF 4 conical theta pinch plasma. A cloud of CF 4 gas was puffed into a conical theta pinch coil, converted to plasma, and propelled into the vacuum region ahead of the expanding gas cloud. At a position 67 cm away from the conical theta pinch coil, the plasma arrived in separate packets that were about 20 μs in duration. The average drift velocity of these packets corresponded to an energy of about 3 eV. The OMA measurements showed that the second packet contained neutral atomic fluorine as well as charged particles

Comparative study of millennials' (age 20-34 years) grip and lateral pinch with the norms.

Science.gov (United States)

Fain, Elizabeth; Weatherford, Cara

Cross-sectional research design. Clinical practice continues to use normative data for grip and pinch measurements that were established in 1985. There is no updated norms despite different hand usage patterns in today's society. Measuring and comparing grip and pinch strengths with normative data is a valid method to determine hand function. This research was implemented to compare the grip and pinch measurements obtained from healthy millennials to the established norms and to describe hand usage patterns for millennials. Grip and lateral pinch measurements were obtained from a sample of 237 healthy millennials (ages 20-34 years). Strength scores were statistically lower that older normative data in all millennial grip strengths, with the exception of the women in the age group of 30-34 years. Specifically, this statistically significant trend was observed in all male grip strengths, as well as in women in the age group of 20-24 years (bilateral grip) and 25-29 years (right grip). However, the lateral pinch data reflected was similar to the older norms with variances of 0.5-1 kg. Current data reflect statistically significant differences from the norms for all male grip measurements, as well as for women in the age group of 20-24 years (bilateral grip) and 25-29 years (right grip). No statistical significance was observed in the independent-sample t tests for the lateral pinch in men of all age groups. Statistical significance was noted for lateral pinch for female age groups for the left hand (20-24 years) and for bilateral lateral pinches (30-34 years). IV. Copyright © 2016 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

A simplified MHD model of capillary Z-Pinch compared with experiments

Energy Technology Data Exchange (ETDEWEB)

Shapolov, A.A.; Kiss, M.; Kukhlevsky, S.V. [Institute of Physics, University of Pecs (Hungary)

2016-11-15

The most accurate models of the capillary Z-pinches used for excitation of soft X-ray lasers and photolithography XUV sources currently are based on the magnetohydrodynamics theory (MHD). The output of MHD-based models greatly depends on details in the mathematical description, such as initial and boundary conditions, approximations of plasma parameters, etc. Small experimental groups who develop soft X-ray/XUV sources often use the simplest Z-pinch models for analysis of their experimental results, despite of these models are inconsistent with the MHD equations. In the present study, keeping only the essential terms in the MHD equations, we obtained a simplified MHD model of cylindrically symmetric capillary Z-pinch. The model gives accurate results compared to experiments with argon plasmas, and provides simple analysis of temporal evolution of main plasma parameters. The results clarify the influence of viscosity, heat flux and approximations of plasma conductivity on the dynamics of capillary Z-pinch plasmas. The model can be useful for researchers, especially experimentalists, who develop the soft X-ray/XUV sources. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Pinch-off syndrome: transection of implantable central venous access device

OpenAIRE

Sugimoto, Takuya; Nagata, Hiroshi; Hayashi, Ken; Kano, Nobuyasu

2012-01-01

As the population of people with cancer increases so does the number of patients who take chemotherapy. Majority of them are administered parentally continuously. Implantable central venous catheter device is a good choice for those patients; however, severe complication would occur concerning the devices. Pinch-off syndrome is one of the most severe complications. The authors report a severe case of pinch-off syndrome. The patient with the implantable central venous device could not take che...

Theory of wire number scaling in wire-array Z pinches

International Nuclear Information System (INIS)

Desjarlais, M.P.; Marder, B.M.

1999-01-01

Pulsed-power-driven Z pinches, produced by imploding cylindrical arrays of many wires, have generated very high x-ray radiation powers (>200 TW) and energies (2 MJ). Experiments have revealed a steady improvement in Z-pinch performance with increasing wire number at fixed total mass and array radius. The dominant mechanism acting to limit the performance of these devices is believed to be the Rayleigh-Taylor instability which broadens the radially imploding plasma sheath and consequently reduces the peak radiation power. A model is presented which describes an amplification over the two-dimensional Rayleigh-Taylor growth rate brought about by kink-like forces on the individual wires. This amplification factor goes to zero as the number of wires approaches infinity. This model gives results which are in good agreement with the experimental data and provides a scaling for wire-array Z pinches. copyright 1999 American Institute of Physics

3D modeling of instabilities in multi-wire Z pinches

International Nuclear Information System (INIS)

Haill, T.A.; Desjarlais, M.P.; Marder, B.M.; Robinson, A.C.

1998-01-01

Recent success in generating large x-ray energies and powers from large wire-number Z pinch arrays has revived a strong interest in MHD and magneto-Rayleigh-Taylor (RT) instabilities. Two-dimensional r-z simulations of Z pinches typically start calculations with a preformed plasma sheath and seed RT instabilities with a random density perturbation. The magnitude of the random density perturbation is tuned so that the calculated x-ray radiation pulse matches the amplitude and pulse-width of experimentally measured data. While these calculations have been extremely useful in understanding the effect of RT instabilities on experiments, they do not capture all of the three-dimension structure seen in experimental images and are not truly predictive in nature. To remedy this shortcoming Sandia is developing a 3D nature of Z pinch dynamics, namely the merger of arrays of wires into a plasma sheath

Dynamics of low density coronal plasma in low current x-pinches

International Nuclear Information System (INIS)

Haas, D; Bott, S C; Vikhrev, V; Eshaq, Y; Ueda, U; Zhang, T; Baranova, E; Krasheninnikov, S I; Beg, F N

2007-01-01

Experiments were performed on an x-pinch using a pulsed power current generator capable of producing an 80 kA current with a rise time of 50 ns. Molybdenum wires with and without gold coating were employed to study the effect of high z coating on the low-density ( 18 cm -3 ) coronal plasma dynamics. A comparison of images from XUV frames and optical probing shows that the low density coronal plasma from the wires initially converges at the mid-plane immediately above and below the cross-point. A central jet is formed which moves with a velocity of 6 x 10 4 ms -1 towards both electrodes forming a z-pinch column before the current maximum. A marked change in the low density coronal plasma dynamics was observed when molybdenum wires coated with ∼ 0.09 μm of gold were used. The processes forming the jet structure were delayed relative to bare Mo x-pinches, and the time-resolved x-ray emission also showed differences. An m = 0 instability was observed in the coronal plasma along the x-pinch legs, which were consistent with x-ray PIN diode signals in which x-ray pulses were observed before x-ray spot formation. These early time x-ray pulses were not observed with pure molybdenum x-pinches. These observations indicate that a thin layer of gold coating significantly changes the coronal plasma behaviour. Two dimensional MHD simulations were performed and qualitatively agree with experimental observations of low density coronal plasma

Measurements of hot spots and electron beams in Z-pinch devices

International Nuclear Information System (INIS)

Deeney, C.

1988-04-01

Hot spots and Electron Beams have been observed in different types of Z-pinches. There is, however, no conclusive evidence on how either are formed although there has been much theoretical interest in both these phenomena. In this thesis, nanosecond time resolved and time correlated, X-ray and optical diagnostics, are performed on two different types of Z-pinch: a 4 kJ, 30 kV Gas Puff Z-pinch and a 28 kJ, 60 kV Plasma Focus. The aim being to study hot spots and electron beams, as well as characterise the plasma, two different Z-pinch devices. Computer codes are developed to analyse the energy and time resolved data obtained in this work. These codes model both, X-ray emission from a plasma and X-ray emission due to electron beam bombardment of a metal surface. The hot spot and electron beam parameters are measured, from the time correlated X-ray data using these computer codes. The electron beams and the hot spots are also correlated to the plasma behaviour and to each other. The results from both devices are compared with each other and with the theoretical work on hot spot and electron beam formation. A previously unreported 3-5 keV electron temperature plasma is identified, in the gas puff Z-pinch plasma, prior to the formation of the hot spots. it is shown, therefore, that the hot spots are more dense but not hotter than the surrounding plasma. Two distinct periods of electron beam generation are identified in both devices. (author)

On the dynamics of cylindrical z-pinch

International Nuclear Information System (INIS)

Solov'ev, L.S.

1984-01-01

The stationary configurations of cylindrical plasma flow in the framework of two-liquid relativistic electromagnetic gas dynamics (REMG)) and nonlinear radial oscillations of the plasma cylinder with longitudinal current in the framework of classical monoliquid MGD are considered. It is shown that at sufficiently high conductivity Z-pinch is stable relative to one-dimensional radial perturbations and its motion represents respectively nonlinear radial oscillations. In case of a rather low conductivity or low particle concentration there is in cross section a stability also in relation to the development of sausage type instability. The performed investigations of cylindrical equilibrium and radial oscillations give a qualitative representation on plasma behaviour in Z-pinch at the initial stage of it compression and expansion as well as on motion in an average plane of the developing sausage type instability

Review of the current status of linear hybrid reactor concepts

International Nuclear Information System (INIS)

Schultz, K.R.

1977-07-01

A review was made of the current status of linear fusion-fission hybrid reactor design studies in the USA. The linear hybrid reactor concepts reviewed include the linear theta-pinch hybrid reactor being studied at Los Alamos Scientific Laboratory, the electron beam-heated solenoid hybrid reactor under development at Physics International Co., the laser-heated solenoid hybrid reactor being investigated at Mathematical Sciences Northwest, Inc., and the linear fusion waste burning reactor being studied at General Atomic Company. The discussion addresses confinement and heating mechanisms for each concept, as well as the hybrid blanket designs. The current state of the four reactor designs is summarized and the performance of the various concepts compared

Comparative Studies of Traditional (Non-Energy Integration and Energy Integration of Catalytic Reforming Unit using Pinch Analysis

Directory of Open Access Journals (Sweden)

M. Alta

2012-12-01

Full Text Available Energy Integration of Catalytic Reforming Unit (CRU of Kaduna Refinery and petrochemicals Company Kaduna Nigeria was carried out using Pinch Technology. The pinch analysis was carried out using Maple. Optimum minimum approach temperature of 20 °C was used to determine the energy target. The pinch point temperature was found to be 278 °C. The utilities targets for the minimum approach temperature were found to be 72711839.47 kJ/hr and 87105834.43 kJ/hr for hot and cold utilities respectively. Pinch analysis as an energy integration technique was found to save more energy and utilities cost than the traditional energy technique. Key words: Pinch point, CRU, Energy Target, Maple

Design and experimental research on a self-magnetic pinch diode under MV

Science.gov (United States)

Pengfei, ZHANG; Yang, HU; Jiang, SUN; Yan, SONG; Jianfeng, SUN; Zhiming, YAO; Peitian, CONG; Mengtong, QIU; Aici, QIU

2018-01-01

A self-magnetic pinch diode (SMPD) integrating an anode foil-reinforced electron beam pinch focus and a small high-dose x-ray spot output was designed and optimized. An x-ray focal spot measuring system was developed in accordance with the principle of pinhole imaging. The designed SMPD and the corresponding measuring system were tested under ∼MV, with 1.75 × 2 mm2 oval x-ray spots (AWE defined) and forward directed dose 1.6 rad at 1 m. Results confirmed that the anode foil can significantly strengthen the electron beam pinch focus, and the focal spot measuring system can collect clear focal spot images. This finding indicated that the principle and method are feasible.

Design and experimental research on a self-magnetic pinch diode under MV

Institute of Scientific and Technical Information of China (English)

Pengfei ZHANG; Yang HU; Jiang SUN; Yan SONG; Jianfeng SUN; Zhiming YAO; Peitian CONG; Mengtong QIU; Aici QIU

2018-01-01

A self-magnetic pinch diode (SMPD) integrating an anode foil-reinforced electron beam pinch focus and a small high-dose x-ray spot output was designed and optimized.An x-ray focal spot measuring system was developed in accordance with the principle of pinhole imaging.The designed SMPD and the corresponding measuring system were tested under ～MV,with 1.75 × 2 mm2 oval x-ray spots (AWE defined) and forward directed dose 1.6 rad at 1 m.Results confirmed that the anode foil can significantly strengthen the electron beam pinch focus,and the focal spot measuring system can collect clear focal spot images.This finding indicated that the principle and method are feasible.

Diagnostics for Z-pinch implosion experiments on PTS

Energy Technology Data Exchange (ETDEWEB)

Ren, X. D., E-mail: amosrxd@163.com; Huang, X. B., E-mail: amosrxd@163.com; Zhou, S. T., E-mail: amosrxd@163.com; Zhang, S. Q., E-mail: amosrxd@163.com; Dan, J. K., E-mail: amosrxd@163.com; Li, J., E-mail: amosrxd@163.com; Cai, H. C., E-mail: amosrxd@163.com; Wang, K. L., E-mail: amosrxd@163.com; Ouyang, K., E-mail: amosrxd@163.com; Xu, Q., E-mail: amosrxd@163.com; Duan, S. C., E-mail: amosrxd@163.com; Chen, G. H., E-mail: amosrxd@163.com; Wang, M., E-mail: amosrxd@163.com; Feng, S. P., E-mail: amosrxd@163.com; Yang, L. B., E-mail: amosrxd@163.com; Xie, W. P., E-mail: amosrxd@163.com; Deng, J. J., E-mail: amosrxd@163.com [Key Lab of Pulsed Power, Institute of Fluid Physics, CAEP, P.O. Box 919-108, Mianyang, Sichuan 621999 (China)

2014-12-15

The preliminary experiments of wire array implosion were performed on PTS, a 10 MA z-pinch driver with a 70 ns rise time. A set of diagnostics have been developed and fielded on PTS to study pinch physics and implosion dynamics of wire array. Radiated power measurement for soft x-rays was performed by multichannel filtered x-ray diode array, and flat spectral responses x-ray diode detector. Total x-ray yield was measured by a calibrated, unfiltered nickel bolometer which was also used to obtain pinch power. Multiple time-gated pinhole cameras were used to produce spatial-resolved images of x-ray self-emission from plasmas. Two time-integrated pinhole cameras were used respectively with 20-μm Be filter and with multilayer mirrors to record images produced by >1-keV and 277±5 eV self-emission. An optical streak camera was used to produce radial implosion trajectories, and an x-ray streak camera paired with a horizontal slit was used to record a continuous time-history of emission with one-dimensional spatial resolution. A frequency-doubled Nd:YAG laser (532 nm) was used to produce four frame laser shadowgraph images with 6 ns time interval. We will briefly describe each of these diagnostics and present some typical results from them.

Discharge breakdown in the EXTRAP configuration

International Nuclear Information System (INIS)

Drake, J.R.

1982-02-01

The breakdown of a discharge in a linear EXTRAP configuration has been studied experimentally. In this configuration the breakdown occurs along the zero B-field line, which is the axis of the linear octupole magnetic field, between the anode and cathode which constitute the ends of the linear device. Breakdown could be described by a modified Townsend criterion which included additional electron losses due to the presence of the B-field transverse to the discharge. (author)

Exact self-similar solutions for the magnetized Noh Z pinch problem

International Nuclear Information System (INIS)

Velikovich, A. L.; Giuliani, J. L.; Thornhill, J. W.; Zalesak, S. T.; Gardiner, T. A.

2012-01-01

A self-similar solution is derived for a radially imploding cylindrical plasma with an embedded, azimuthal magnetic field. The plasma stagnates through a strong, outward propagating shock wave of constant velocity. This analysis is an extension of the classic Noh gasdynamics problem to its ideal magnetohydrodynamics (MHD) counterpart. The present exact solution is especially suitable as a test for MHD codes designed to simulate linear Z pinches. To demonstrate the application of the new solution to code verification, simulation results from the cylindrical R-Z version of Mach2 and the 3D Cartesian code Athena are compared against the analytic solution. Alternative routines from the default ones in Athena lead to significant improvement of the results, thereby demonstrating the utility of the self-similar solution for verification.

Stabilization of long wavelength sausage and kink modes of a Z-pinch by nonlinear radial oscillations

International Nuclear Information System (INIS)

Bud'ko, A.B.; Karlson, E.T.; Liberman, M.A.

1992-01-01

A number of experiments with fiber-initiated dense Z-pinches, with compressional and gas-embedded Z-pinches, with imploding gas-puff Z-pinches and the straight Extrap configuration performed in the last decade demonstrated sufficiently improved stability of Z-pinch configurations. The striking stability with respect to the sausage modes can be explained, in principle, by ideal MHD theory as well as by finite plasma conductivity effects. The global kink mode can not be stabilized by the appropriate choice of the unperturbed profiles neither within the scope of the ideal MHD nor taking into account finite ion Larmor radius and viscous damping effects. In this report we shall demonstrate that stabilization of the global kink modes can be explained by the assumption that pinch is not in a stationary but in a dynamic equilibrium. (author) 12 refs., 2 figs

Murakami density limit in tokamaks and reversed-field pinches

International Nuclear Information System (INIS)

Perkins, F.W.; Hulse, R.A.

1984-03-01

A theoretical upper limit for the density in an ohmically heated tokamak discharge follows from the requirement that the ohmic heating power deposited in the central current-carrying channel exceed the impurity radiative cooling in this critical region. A compact summary of our results gives this limit n/sub M/ for the central density as n/sub M/ = [Z/sub e//(Z/sub e/-1]/sup 1/2/n/sub eo/ (B/sub T//1T)(1m/R) where n/sub eo/ depends strongly on the impurity species and is remarkably independent of the central electron temperature T/sub e/(0). For T/sub e/(0) approx. 1 keV, we have n/sub eo/ = 1.5 x 10 14 cm -3 for beryllium, n/sub eo/ = 5 x 10 13 cm -3 for oxygen, n/sub eo/ = 1.0 x 10 13 cm -3 for iron, and n/sub eo/ = 0.5 x 10 13 cm -3 for tungsten. The results agree quantitatively with Murakami's original observations. A similar density limit, known as the I/N limit, exists for reversed-field pinch devices and this limit has also been evaluated for a variety of impurity species

Progress in Z-pinch research driven by the mega-ampere device SPEED2

International Nuclear Information System (INIS)

Pavez, Cristian; Soto, Leopoldo; Moreno, Jose; Sylvester, Gustavo; Tarifeno, Ariel

2008-01-01

Several pinch configurations have being studied at the Chilean Nuclear Energy Commission using the SPEED2 generator: plasma focus, gas embedded z-pinch and wire arrays. SPEED2 is a generator based on Marx technology (4.1 μF equivalent Marx generator capacity, 300 kV, 4 MA in short circuit, 187 kJ, 400 ns rise time, dI/dt∼10 13 A/s). Currently the device is being operated at 70kJ stored energy producing a peak current of 2.4 MA in short circuit. In this work results related to studies in gas embedded z-pinch in deuterium and studies in wire arrays are presented.

Progress in Z-pinch research driven by the mega-ampere device SPEED2

International Nuclear Information System (INIS)

Pavez, Cristian; Soto, Leopoldo; Moreno, Jose; Tarifeno, Ariel; Sylvester, Gustavo

2008-01-01

Several pinch configurations have being studied at the Chilean Nuclear Energy Commission using the SPEED2 generator: plasma focus, gas embedded z-pinch and wire arrays. SPEED2 is a generator based on Marx technology (4.1 μF equivalent Marx generator capacity, 300 kV, 4 MA in short circuit, 187 kJ, 400 ns rise time, dI/dt∼10 13 A/s). Currently the device is being operated at 70kJ stored energy producing a peak current of 2.4 MA in short circuit. In this work results related to studies in gas embedded z-pinch in deuterium and studies in wire arrays are presented

Study of X-ray emission in aluminium z-pinches

International Nuclear Information System (INIS)

Rosch, R.

1999-01-01

Previous experiments, at 0.1. TX level, have shown that stability and x-ray emission of fast Z-pinches, could be strongly increased by imploding an aluminium vapor jet onto a very thin coaxial wire. We present here first results of an aluminium Z-pinch, using a similar liner, but at mega-ampere level. The pinch is driven by AMBIORIX high-power facility, a 2 TW, 0.5 Ω, 2 MA, 50 ns pulse-line generator. We study the effect of an aluminium wire and its diameter (20-50 μm) on the implosion dynamics, on x-ray yield on MHD stability of the column at stagnation. Analysis of A1 jet on A1 wire shots demonstrates that x-ray yield due to emission processes in the H- and He- like ionization stages (i.e. the K-shell) is significantly enhanced, relative to that of A1 jet only ones. The wire also leads to better symmetry of the implosion, and to better reproducibility of shots. X-ray signals exhibit two similar pulses, 10 ns in width, 15 ns spaced. To discern spectral origin of both pulses, experiments are realized with stainless steel wire (25 μm in diameter). Results show that liner and wire radial simultaneously and contribute to both pulses. Analysis of a typical A1 jet on A1 wire shot, using detailed collisional-radiative equilibrium (CRE) model is also given in this thesis. View o the pinch at stagnation as a cola-dense core surrounded by a hot-low density corona reproduces all features of the X-ray data. (author)

Performance of soft x-ray laser pumped by capillary discharge

International Nuclear Information System (INIS)

Sakai, Yusuke; Kakuya, Yuji; Xiao, Yifan

2005-01-01

We report the output characteristics of capillary discharge single-pass 46.9 nm Ne-like Ar soft-X-ray laser generated by a capillary z-pinch discharge. The coherence properties of the laser have shown to be improved with the increase of the length of laser amplifier from 20 up to 35 cm. The high degree of the spatial coherence of the laser beam produced by 35 cm long capillary is demonstrated by the results obtained in a classical Young's double-slit experiments. We found that the coherence length of the laser is 50 μm. For the 20 cm-long capillary, the diameter of a laser beam is in a range from 3.2 to 4.0 mm, which is corresponding to a range of divergence from 2.2 to 2.8 mrad. Finally, we introduce two spikes on X-ray diode (XRD) signal observed in a single shot. (author)

A heuristic model of the wire array z-pinch

International Nuclear Information System (INIS)

Haines, M.G.

1998-01-01

Recent experimental results at the Sandia National Laboratory have shown that the X-ray power increases as the number of wires n employed is increased, with a sharper increase in power when the wire gap is below a critical value. This paper proposes a model that can not only explain these phenomena, but also shows how the initial perturbations that lead to the Rayleigh-Taylor instability scale as n -1/2 . The model predicts the shell thickness at merger of the expanding separate wires which will mainly determine the final pinch radius. The largest amplitude Rayleigh-Taylor mode at the pinch time is also found, in reasonable agreement with experiment

Explosive instabilities of reaction-diffusion equations including pinch effects

International Nuclear Information System (INIS)

Wilhelmsson, H.

1992-01-01

Particular solutions of reaction-diffusion equations for temperature are obtained for explosively unstable situations. As a result of the interplay between inertial, diffusion, pinch and source processes certain 'bell-shaped' distributions may grow explosively in time with preserved shape of the spatial distribution. The effect of the pinch, which requires a density inhomogeneity, is found to diminish the effect of diffusion, or inversely to support the inertial and source processes in creating the explosion. The results may be described in terms of elliptic integrals or. more simply, by means of expansions in the spatial coordinate. An application is the temperature evolution of a burning fusion plasma. (au) (18 refs.)

Study of X-ray emission in aluminium z-pinches; Etude de l'emission X dans les plasmas d'aluminium de type Z-pinch

Energy Technology Data Exchange (ETDEWEB)

Rosch, R [CEA/DAM-Ile de France, Dept. de Conception et Realisation des Experimentations (DCRE), 91 - Bruyeres-le-Chatel (France); [Paris-11 Univ., 91 - Orsay (France)

1999-07-01

Previous experiments, at 0.1. TX level, have shown that stability and x-ray emission of fast Z-pinches, could be strongly increased by imploding an aluminium vapor jet onto a very thin coaxial wire. We present here first results of an aluminium Z-pinch, using a similar liner, but at mega-ampere level. The pinch is driven by AMBIORIX high-power facility, a 2 TW,0.5 {omega}, 2 MA, 50 ns pulse-line generator. We study the effect of an aluminium wire and its diameter (20-50 {mu}m) on the implosion dynamics, on x-ray yield on MHD stability of the column at stagnation. Analysis of A1 jet on A1 wire shots demonstrates that x-ray yield due to emission processes in the H- and He- like ionization stages (i.e. the K-shell) is significantly enhanced, relative to that of A1 jet only ones. The wire also leads to better symmetry of the implosion, and to better reproducibility of shots. X-ray signals exhibit two similar pulses, 10 ns in width, 15 ns spaced. To discern spectral origin of both pulses, experiments are realized with stainless steel wire (25 {mu}m in diameter). Results show that liner and wire radial simultaneously and contribute to both pulses. Analysis of a typical A1 jet on A1 wire shot, using detailed collisional-radiative equilibrium (CRE) model is also given in this thesis. View o the pinch at stagnation as a cola-dense core surrounded by a hot-low density corona reproduces all features of the X-ray data. (author)

DT ignition in a Z pinch compressed by an imploding liner

International Nuclear Information System (INIS)

Bilbao, L.; Bernal, L.; Linhart, J.G.; Verri, G.

2001-01-01

It has been shown that an m=0 instability of a Z pinch carrying a current of the order of 10 MA with a rise time of less than 10 ns can generate a spark capable of igniting a fusion detonation in the adjacent DT plasma channel. A possible method for generating such currents, necessary for the implosion of an initial large radius, low temperature Z pinch, can be a radial implosion of a cylindrical fast liner. The problem has been addressed in previous publications without considering the role played by an initially impressed m=0 perturbation, a mechanism indispensable for the generation of a spark. The liner-Z pinch dynamics can be solved at several levels of physical model completeness. The first corresponds to a zero dimensional model in which the liner has a given mass per unit length and a zero thickness, the plasma is compressed adiabatically and is isotropic, and there are no energy losses or Joule heating. The second level is one dimensional. The Z pinch plasma is described by the full set of MHD, two-fluid equations. The liner is treated first as thin and incompressible, and subsequently it is assumed that it has a finite thickness and is composed of a heavy ion plasma, having an artificial but realistic equation of state. Both plasma and liner are considered uniform in the Z direction and only DT reactions are considered. It is shown that, given sufficient energy and speed of the liner, the Z pinch can reach a volume ignition. The third level is two dimensional. Plasma and liner are treated as in the second level but either the Z pinch or the liner is perturbed by an m=0 non-uniformity. Provided the liner energy is high enough and the initial m=0 perturbation is correctly chosen, the final neck plasma can act as a spark for DT ignition. It is also shown that the liner energy required for generating a spark and the subsequent detonation propagation are considerably less than in the case of volume ignition. (author)

Linear analysis of sheared flow stabilization of global magnetohydrodynamic instabilities based on the Hall fluid model

International Nuclear Information System (INIS)

Sotnikov, V.I.; Paraschiv, I.; Makhin, V.; Bauer, B.S.; Leboeuf, J.N.; Dawson, J.M.

2002-01-01

A systematic study of the linear stage of sheared flow stabilization of Z-pinch plasmas based on the Hall fluid model with equilibrium that contains sheared flow and an axial magnetic field is presented. In the study we begin with the derivation of a general set of equations that permits the evaluation of the combined effect of sheared flow and axial magnetic field on the development of the azimuthal mode number m=0 sausage and m=1 kink magnetohydrodynamic (MHD) instabilities, with the Hall term included in the model. The incorporation of sheared flow, axial magnetic field, and the Hall term allows the Z-pinch system to be taken away from the region in parameter space where ideal MHD is applicable to a regime where nonideal effects tend to govern stability. The problem is then treated numerically by following the linear development in time of an initial perturbation. The numerical results for linear growth rates as a function of axial sheared flow, an axial magnetic field, and the Hall term are reported

Properties of the edge plasma in the rebuilt Extrap-T2R reversed field pinch experiment

International Nuclear Information System (INIS)

Vianello, N; Spolaore, M; Serianni, G; Bergsaker, H; Antoni, V; Drake, J R

2002-01-01

The edge region of the rebuilt Extrap-T2R reversed field pinch experiment has been investigated using Langmuir probes. Radial profiles of main plasma parameters are obtained and compared with those of the previous device Extrap-T2. The spontaneous setting up of a double shear layer of ExB toroidal velocity is confirmed. The particle flux induced by electrostatic fluctuations is calculated and the resulting effective diffusion coefficient is consistent with the Bohm estimate. A close relationship between electrostatic fluctuations at the edge and non-linear coupling of MHD modes in the core is found

Properties of the edge plasma in the rebuilt Extrap-T2R reversed field pinch experiment

Science.gov (United States)

Vianello, N.; Spolaore, M.; Serianni, G.; Bergsåker, H.; Antoni, V.; Drake, J. R.

2002-12-01

The edge region of the rebuilt Extrap-T2R reversed field pinch experiment has been investigated using Langmuir probes. Radial profiles of main plasma parameters are obtained and compared with those of the previous device Extrap-T2. The spontaneous setting up of a double shear layer of E×B toroidal velocity is confirmed. The particle flux induced by electrostatic fluctuations is calculated and the resulting effective diffusion coefficient is consistent with the Bohm estimate. A close relationship between electrostatic fluctuations at the edge and non-linear coupling of MHD modes in the core is found.

Observation of helical structure in a low energy plasma focus pinch

International Nuclear Information System (INIS)

Rout, R.K.; Shyam, A.

1989-01-01

Helical structure and hot spots were observed in a Mather-type plasma focus operated at 3 KJ of bank energy. The experiments were carried out with the help of a fast optical framing camera and two X-ray pin-hole cameras with different filters. It was observed that initially a conical pinch (with base diameter of 6 mm and length of 14 mm) with temperature of ≅ 10 2 eV was formed. This pinch disintegrated after ≅ 50 ns by a single lobe sausage instability into a central high temperature (≅ 10 3 eV) filament of 1 mm diameter and 8 mm length containing a high emissivity helical structure. This helix is probably responsible for generation of axial magnetic field and relaxation of the focus pinch. Hot spots of high X-ray intensity and temperature (≅ 10 3 eV) were also observed much beyond the filament region. (author)

X pinch a point x-ray source

International Nuclear Information System (INIS)

Garg, A.B.; Rout, R.K.; Shyam, A.; Srinivasan, M.

1993-01-01

X ray emission from an X pinch, a point x-ray source has been studied using a pin-hole camera by a 30 kV, 7.2 μ F capacitor bank. The wires of different material like W, Mo, Cu, S.S.(stainless steel) and Ti were used. Molybdenum pinch gives the most intense x-rays and stainless steel gives the minimum intensity x-rays for same bank energy (∼ 3.2 kJ). Point x-ray source of size (≤ 0.5 mm) was observed using pin hole camera. The size of the source is limited by the size of the pin hole camera. The peak current in the load is approximately 150 kA. The point x-ray source could be useful in many fields like micro lithography, medicine and to study the basic physics of high Z plasmas. (author). 4 refs., 3 figs

Target design for high fusion yield with the double Z-pinch-driven hohlraum

International Nuclear Information System (INIS)

Vesey, R. A.; Herrmann, M. C.; Lemke, R. W.; Desjarlais, M. P.; Cuneo, M. E.; Stygar, W. A.; Bennett, G. R.; Campbell, R. B.; Christenson, P. J.; Mehlhorn, T. A.; Porter, J. L.; Slutz, S. A.

2007-01-01

A key demonstration on the path to inertial fusion energy is the achievement of high fusion yield (hundreds of MJ) and high target gain. Toward this goal, an indirect-drive high-yield inertial confinement fusion (ICF) target involving two Z-pinch x-ray sources heating a central secondary hohlraum is described by Hammer et al. [Phys. Plasmas 6, 2129 (1999)]. In subsequent research at Sandia National Laboratories, theoretical/computational models have been developed and an extensive series of validation experiments have been performed to study hohlraum energetics, capsule coupling, and capsule implosion symmetry for this system. These models have been used to design a high-yield Z-pinch-driven ICF target that incorporates the latest experience in capsule design, hohlraum symmetry control, and x-ray production by Z pinches. An x-ray energy output of 9 MJ per pinch, suitably pulse-shaped, is sufficient for this concept to drive 0.3-0.5 GJ capsules. For the first time, integrated two-dimensional (2D) hohlraum/capsule radiation-hydrodynamics simulations have demonstrated adequate hohlraum coupling, time-dependent radiation symmetry control, and the successful implosion, ignition, and burn of a high-yield capsule in the double Z-pinch hohlraum. An important new feature of this target design is mode-selective symmetry control: the use of burn-through shields offset from the capsule that selectively tune certain low-order asymmetry modes (P 2 ,P 4 ) without significantly perturbing higher-order modes and without a significant energy penalty. This paper will describe the capsule and hohlraum design that have produced 0.4-0.5 GJ yields in 2D simulations, provide a preliminary estimate of the Z-pinch load and accelerator requirements necessary to drive the system, and suggest future directions for target design work

Enhanced rotation velocities and electric fields, sub-neoclassical energy transport and density pinch from revisited neoclassical theory

International Nuclear Information System (INIS)

Rogister, A.

1998-01-01

We show that the large negative radial electric fields which are measured in front of the separatrix in H-mode discharges are easily explainable on the basis of the rigorous 'revisited' neoclassical theory, including finite Larmor radii and inertia effects that was published earlier (Rogister A 1994 Phys. Plasmas 1 619); the same theory naturally leads to sub-neoclassical energy transport and novel particle pinch terms. The calculation has so far been developed only in the high collisionality regime: step sizes comparable to gradient-scale sizes are therefore not required to explain observed properties! Based on the analysis, we conclude that the radial electric field profile develops a well in front of the separatrix when the plasma is unable to sustain ambipolar flows otherwise. (author)

The stability of Z-pinches with equilibrium flows

International Nuclear Information System (INIS)

Howell, D.F.

1999-01-01

According to Ideal Magnetohydrodynamic (MHD) theory the Z-pinch is an inherently unstable magnetic configuration. However it is possible that there exist regimes of operation whereby the predicted instabilities may be reduced or even eliminated. We must look to effects normally ignored in the Ideal MHD model in order to predict such regimes. In this thesis various non-ideal effects will be studied, namely the inclusion of equilibrium flow and finite Larmor radius effects. Astrophysical jets, for example those seen to be emitted from active galactic nuclei, are seen to persist for a greater time than suggested by Ideal MHD before the onset of instabilities. It is postulated that one of the contributing factors to this enhanced stability is the presence of a sheared axial flow. In this thesis we study the stability properties of the Z-pinch where flow is present in the equilibrium. It is found that a sheared axial flow generally has a stabilising effect, the degree of which is determined by the equilibrium and flow profiles, but that absolute stability cannot be achieved due to the onset of the Kelvin-Helmholtz instability. The effect of adding rotation has also been studied. It is found that adding rotation changes the equilibrium density profiles from the static case, and that it always has a destabilising effect. Another postulated method of stabilising the Z-pinch is by increasing the ratio of the ion Larmor radius to the pinch radius, and it is seen to have a stabilising effect for some equilibria in the collisionless regime. In this thesis we study the effects of increasing the Larmor radius in the collisional regime using the Hall fluid model. It is found that for free boundary modes the stability properties are unchanged for experimentally realistic values of the Larmor radius, but for fixed boundary modes a small stabilising effect is noted for some equilibria. (author)

Stabilization of sausage and kink instability modes of a plasma pinch by radial oscillations

International Nuclear Information System (INIS)

Bud'ko, A.B.; Kravchenko, Y.P.; Liberman, M.A.

1995-01-01

The growth of the global sausage (m=0) and kink (m=1) perturbations of a Z-pinch subject to radial oscillations is considered. It is demonstrated that the oscillations result in significant reduction of the growth rate of both kink and sausage instability modes with wavelengths long compared to the pinch radius. The analysis of stability is carried out in two ways. The first method is based on the averaging magnetohydrodynamic equations over the period of radial oscillations. The second one consists in the analysis of the growth of Fourier-components of perturbations. Numerical simulation demonstrates that even moderate radial oscillations cause reduction of the growth rate of long-wavelength sausage instabilities and complete stabilization of long kinks. This can be understood as a result of the effective gravitational field produced in the pinch by the oscillations. The effect in question can explain the anomalous stability of pinches with respect to the kink perturbations observed in experiments. copyright 1995 American Institute of Physics

Study of energy transfer in table-top X-pinch driven by a water line

International Nuclear Information System (INIS)

Beg, F N; Zhang, T; Fedin, D; Beagen, B; Chua, E; Lee, J Y; Rawat, R S; Lee, P

2007-01-01

The current passing through X-pinches and the energy transferring from the pulse forming line to the load are modelled using a simple LCR circuit. A comparison of the electrical properties of two table-top X-pinch devices is made. It was found that up to 25% of the stored energy is transferred from the water transmission line to the load in the University of California,San Diego (UCSD) table-top X-pinch before x-ray emission starts. The highest energy transmitted (75%) is found after the current peak. In comparison, only 3% of the energy is transferred to the load in the National Institute of Education (NIE) X-pinch device just after the maximum current peak. The highest energy (25%) transmitted to the plasma occurs long after the current peak. The plasma in both devices is visually and qualitatively similar. However, the UCSD device emits intense x-rays with no x-rays observed in the NIE device. This observation is consistent with the electrical circuit analysis

Novel phenomena in one-dimensional non-linear transport in long quantum wires

International Nuclear Information System (INIS)

Morimoto, T; Hemmi, M; Naito, R; Tsubaki, K; Park, J-S; Aoki, N; Bird, J P; Ochiai, Y

2006-01-01

We have investigated the non-linear transport properties of split-gate quantum wires of various channel lengths. In this report, we present results on a resonant enhancement of the non-linear conductance that is observed near pinch-off under a finite source-drain bias voltage. The resonant phenomenon exhibits a strong dependence on temperature and in-plane magnetic field. We discuss the possible relationship of this phenomenon to the spin-polarized manybody state that has recently been suggested to occur in quasi-one dimensional systems

MAIZE: a 1 MA LTD-Driven Z-Pinch at The University of Michigan

International Nuclear Information System (INIS)

Gilgenbach, R. M.; Gomez, M. R.; Zier, J. C.; Tang, W. W.; French, D. M.; Lau, Y. Y.; Mazarakis, M. G.; Cuneo, M. E.; Johnston, M. D.; Oliver, B. V.; Mehlhorn, T. A.; Kim, A. A.; Sinebryukhov, V. A.

2009-01-01

Researchers at The University of Michigan have constructed and tested a 1-MA Linear Transformer Driver (LTD), the first of its type to reach the USA. The Michigan Accelerator for Inductive Z-pinch Experiments, (MAIZE), is based on the LTD developed at the Institute of High Current Electronics in collaboration with Sandia National Labs and UM. This LTD utilizes 80 capacitors and 40 spark gap switches, arranged in 40 ''bricks,'' to deliver a 1 MA, 100 kV pulse with 100 ns risetime into a matched resistive load. Preliminary resistive-load test results are presented for the LTD facility.Planned experimental research programs at UM include: a) Studies of Magneto-Raleigh-Taylor instability of planar foils, and b) Vacuum convolute studies including cathode and anode plasma.

A spin-liquid with pinch-line singularities on the pyrochlore lattice.

Science.gov (United States)

Benton, Owen; Jaubert, L D C; Yan, Han; Shannon, Nic

2016-05-26

The mathematics of gauge theories lies behind many of the most profound advances in physics in the past 200 years, from Maxwell's theory of electromagnetism to Einstein's theory of general relativity. More recently it has become clear that gauge theories also emerge in condensed matter, a prime example being the spin-ice materials which host an emergent electromagnetic gauge field. In spin-ice, the underlying gauge structure is revealed by the presence of pinch-point singularities in neutron-scattering measurements. Here we report the discovery of a spin-liquid where the low-temperature physics is naturally described by the fluctuations of a tensor field with a continuous gauge freedom. This gauge structure underpins an unusual form of spin correlations, giving rise to pinch-line singularities: line-like analogues of the pinch points observed in spin-ice. Remarkably, these features may already have been observed in the pyrochlore material Tb2Ti2O7.

Reversed-field pinch configuration with minimum energy and finite beta

International Nuclear Information System (INIS)

Zhang Peng

1989-01-01

The reversed-field pinch (RFP) configuration has been studied for the case of finite beta. Suydam's condition and the sufficient criterion have been used to examine this configuration. Results of numerical calculations show that the critical value of the pinch parameter Θ for the appearance of the reverse toroidal field increases as the β-value increases. The critical value of Θ for the helical state increases with β as well. Suydam's and Robinson's stability regions increase and shift towards higher values of Θ with increasing β. Theoretical results for finite β coincide with recent RFP experimental results

The effect of magnetic field configuration on particle pinch velocity in compact helical system (CHS)

International Nuclear Information System (INIS)

Iguchi, H.; Ida, K.; Yamada, H.

1994-01-01

Radial particle transport has been experimentally studied in the low-aspect-ratio heliotron/torsatron device CHS. A non-diffusive outward particle flow (inverse pinch) is observed in the magnetic configuration with the magnetic axis shifted outward, while an inward pinch, like in tokamaks, is observed with the magnetic axis shifted inward. This change in the direction of anomalous particle flow is not due to the reversal of temperature gradient nor the radial electric field. The observation suggests that the particle pinch velocity is sensitive to the magnetic field structure. (author)

Formation of toroidal pre-heat plasma without residual magnetic field for high-beta pinch experiments

International Nuclear Information System (INIS)

Ikeda, Nagayasu; Tamaru, Ken; Nagata, Akiyoshi.

1979-01-01

Formation of toroidal pre-heat plasma was studied. The pre-heat plasma without residual magnetic field was made by chopping the current for pre-heat, A small toroidal-pinch system was used for the experiment. The magnetic field was measured with a magnetic probe. One turn loop was used for the measurement of the toroidal one-turn electric field. A pair of Rogoski coil was used for the measurement of plasma current. The dependence of residual magnetic field on chopping time was measured. By fast chopping of the primary current in the pre-heating circuit, the poloidal magnetic field was reduced to several percent within 5 microsecond. After chopping, no instability was observed in the principal discharge plasma produced within several microsecond. As the conclusion, it can be said that the control of residual field can be made by current chopping. (Kato, T.)

Los Alamos Compact Toroid, fast liner, and High-Density Z-Pinch programs

International Nuclear Information System (INIS)

Linford, R.K.; Hammel, J.E.; Sherwood, H.R.

1982-01-01

The compact Toroid and High Density Z-Pinch are two of the plasma configurations presently being studied at Los Alamos. This paper summarizes these two programs along with the recently terminated Fast Liner Program. Included in this discussion is an analysis of compact Toroid formation techniques showing the tearing and reconnection of the fields that separate the spheromak from the radial fields of the coaxial source, and the final equilibrium state of the elongated FRC in the theta-pinch coil. In addition the typical dimensions of the geometry of the Fast Liner experiments are delineated Z-pinch and electrode assembly is displayed as is a graphic of the temporal behavior of the current required for radial equilibrium. Spheromak is examined in terms of formation, gross stability, and equilibrium and field reversed configuration is discussed in terms of gross stability, equilibrium, and confinement scaling

Interferometric characterization of density dynamics of an ultradense Z-pinch plasma

International Nuclear Information System (INIS)

Ackenhusen, J.G.; Bach, D.R.

1979-01-01

We have measured the spatially and temporally resolved density in a Z-pinch plasma by holographic interferometry. The high electron density (4 x 10 19 e/cm 3 ), short density scale length (100 μm), and low temperature (about 20 eV) make the plasma source suitable for simulation of laser-pellet interaction experiments at 10.6-μm laser wavelengths. A cinema of density evolution, indicating plasma pinching and subsequent relaxation, provides an experimental view of plasma dynamics which is then compared to simple theoretical models

A study of Z-pinch in capillary filled by boron vapours

Czech Academy of Sciences Publication Activity Database

Vrba, Pavel; Vrbová, M.; Bobrova, N. A.; Sasorov, P. V.

2009-01-01

Roč. 51, č. 2 (2009), s. 481-486 ISSN 1434-6079. [Symposium on Plasma Physics and Technology/23rd./. Praha, 16.06.2008-19.06.2008] R&D Projects: GA ČR GA102/07/0275; GA MŠk LA08024 Institutional research plan: CEZ:AV0Z20430508 Keywords : Z-pinches * plasma focus and other pinch devices * Plasma devices for generation of coherent radiation * Magnetohydrodynamics and fluid equation Subject RIV: BH - Optics, Masers, Lasers www.edpsciences.org/epjd nebo www.epj.org

Quantification of hand function by power grip and pinch strength force measurements in ulnar nerve lesion simulated by ulnar nerve block.

Science.gov (United States)

Wachter, Nikolaus Johannes; Mentzel, Martin; Krischak, Gert D; Gülke, Joachim

2017-06-24

In the assessment of hand and upper limb function, grip strength is of the major importance. The measurement by dynamometers has been established. In this study, the effect of a simulated ulnar nerve lesion on different grip force measurements was evaluated. In 25 healthy volunteers, grip force measurement was done by the JAMAR dynamometer (Fabrication Enterprises Inc, Irvington, NY) for power grip and by a pinch strength dynamometer for tip pinch strength, tripod grip, and key pinch strength. A within-subject research design was used in this prospective study. Each subject served as the control by preinjection measurements of grip and pinch strength. Subsequent measurements after ulnar nerve block were used to examine within-subject change. In power grip, there was a significant reduction of maximum grip force of 26.9% with ulnar nerve block compared with grip force without block (P force could be confirmed. However, the assessment of other dimensions of hand strength as tip pinch, tripod pinch and key pinch had more relevance in demonstrating hand strength changes resulting from an distal ulnar nerve lesion. The measurement of tip pinch, tripod grip and key pinch can improve the follow-up in hand rehabilitation. II. Copyright © 2017 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

Scintillator power meter applied on Z-pinch plasma soft X-ray yield measurement

International Nuclear Information System (INIS)

Zhang Siqun; Huang Xianbin; Li Jing; Dan Jiakun; Li Jun; Yang Libing; Cui Mingqi; Zhao Yidong

2010-01-01

This paper presents the configuration and measuring parameters of scintillator power meter applied in Z-pinch plasma soft X-ray yield measurement on Yang accelerator. It also introduces the calibration experiment on BSRF, and analyzes the defect of the power meter from calibration results, the possible errors and feasible method for correcting the errors. The measuring results are revised according to spectrum acquired from Dante spectrometer. The revised discrepancy of two instruments is decreased from over 30% to subter-15%. Finally, the result of yield measurement of the puff Z-pinch X-ray radiation is reported as well, i.e., hundreds of Joule, multigigawatt levels of soft X ray radiation were produced by puff Z-pinch on Yang accelerator. (authors)

PINCH1 regulates cell-matrix and cell-cell adhesions, cell polarity and cell survival during the peri-implantation stage

DEFF Research Database (Denmark)

Li, Shaohua; Bordoy, Randi; Stanchi, Fabio

2005-01-01

PINCH1 is composed of 5 LIM domains, binds integrin-linked kinase (ILK) and locates to integrin-mediated adhesion sites. In order to investigate PINCH1 function we generated mice and embryonic stem (ES) cell-derived embryoid bodies (EBs) lacking the PINCH1 gene. Similar to mice lacking beta1...... integrin or Ilk, loss of PINCH1 arrested development at the peri-implantation stage. In contrast to beta1 integrin or Ilk mutants, however, disruption of the PINCH1 gene produced implantation chambers with visible cell clumps even at embryonic day 9.5. In order to define the phenotype leading to the peri...... not observed in beta1 integrin- or ILK-deficient mice or EBs, included abnormal cell-cell adhesion of endoderm and epiblast as well as the presence of apoptotic cells in the endodermal cell layer. Although ILK and PINCH1 were shown to be involved in the phosphorylation of serine-473 of PKB/Akt, immunostaining...

The TITAN reversed-field-pinch fusion reactor study

International Nuclear Information System (INIS)

1990-01-01

This paper on titan plasma engineering contains papers on the following topics: reversed-field pinch as a fusion reactor; parametric systems studies; magnetics; burning-plasma simulations; plasma transient operations; current drive; and physics issues for compact RFP reactors

Nonlinear dynamics of tearing modes in the reversed field pinch

International Nuclear Information System (INIS)

Holmes, J.A.; Carreras, B.A.; Diamond, P.H.; Lynch, V.E.

1988-01-01

The results of investigations of nonlinear tearing-mode dynamics in reversed field pinch plasmas are described. The linear instabilities have poloidal mode number m = 1 and toroidal mode numbers 10approx. < napprox. <20, and the resonant surfaces are therefore in the plasma core. The nonlinear dynamics result in dual cascade processes. The first process is a rapid m = 1 spectral broadening toward high n, with a simultaneous spreading of magnetic turbulence radially outward toward the field-reversal surface. Global m = 0 perturbations, which are driven to large amplitudes by the m = 1 instabilities, in turn trigger the m = 1 spectral broadening by back coupling to the higher n. The second process is a cascade toward large m and is mediated by m = 2 modes. The m = 2 perturbations have the structure of localized, driven current sheets and nonlinearly stabilize the m = 1 modes by transferring m = 1 energy to small-scale dissipation. The calculated spectrum has many of the qualitative features observed in experiments

Stable and Unstable Behaviour of Preheated Plasma in Linear and Cusped Theta Pinches; Comportement de Plasmas Prechauffes Stables et Instables Soumis a des Strictions Azimutales Lineaires et Cuspidees; Ustojchivoe i neustojchivoe povedenie predvaritel'no nagretoj plazmy v teta-pinch razryadakh s linejnoj i antiprobkovoj geometriej; Comportamiento de Plasmas Precalentados, Estables e Inestables, Sometidos a Constricciones Azimutales de Geometria Lineal y Cuspidal

Energy Technology Data Exchange (ETDEWEB)

Belitz, R. J.; Bogen, P.; Dippel, K. H.; Jordan, H. L.; Kugler, E.; Miyahara, A.; Noll, P.; Schlueter, J.; Witulski, H. [Association EURATOM-Kernforschungsanlage, Juelich (Germany)

1966-04-15

Experiments on the behaviour of the magnetic compression of preheated hydrogen plasmas in theta pinches of linear and spindle-cusped geometries have been made with the following devices: 1) 5kJ linear theta pinch, coil diameter 4.5 cm, length 15 cm, B{sub max} = 50 kGT{sub Vulgar-Fraction-One-Half} = 1.5 {mu}sec; 2) 600-kJ linear theta pinch, coil diameter 10.5 cm, length 128 cm, B{sub max} = 100 kG, T{sub Vulgar-Fraction-One-Half} = 17 {mu}sec; 3) 10-kJ spindle' cusped theta with B{sub max} = 45 kG at point and line cusps, radius 5.2 cm, length 8.5 cm. They all have provisions for preionization by. a capacitively-coupled low-power RF transmitter, magnetic bias field of variable strength and polarity, preheating by pulsed oscillating electrodeless ring discharge, and compression of the plasma by a fast capacitor bank. Observations have been made by using smear and framing camera photography, optical interferometry with Mach-Zehnder and differential interferometers, spectroscopy in the visible and the soft X-ray regions, and magnetic probes. These methods give information on plasma structure, on density profiles, on the distribution of electron and ion-Doppler temperatures and their development in time. Both stable and unstable plasmas were observed in linear devices. By variation of pressure, bias field, preionization, preheating, and impurity concentration, and by disturbing the symmetry of the discharge tube, information on stable and unstable parameter regions could be obtained. Deviations from the symmetry of 1 the plasma column can occur because of: (1) drifts connected with spatial inhomogeneities of the confining magnetic field; (2) axial motions and contractions in plasmas with trapped antiparallel fields, and rarefaction waves due to end losses; (3) rotations, and deformation oscillations of the cross-section of the plasma; and (4) star-shaped instabilities and eruptions. While drifts and axial motions are directly connected with magnetic field

Dense X-pinch plasmas for x-ray microlithography

International Nuclear Information System (INIS)

Kalantar, D.H.; Hammer, D.A.; Qi, N.; Mittal, K.C.

1990-01-01

The authors report experimental results from a study of the radiation emission from aluminum and magnesium x-pinch experiments. The single cross x-pinch, driven by the 0.5 TW, 40ns pulse width Lion accelerator, consists of 2-8 fine wires stretched between the output electrodes of Lion so as to touch at a single point. The wires were twisted up to 360 degrees at the crossing point. The number and size of Al and Mg wires were varied in order to optimize the K-shell line radiation. Diagnostics used for the experiments included pinhole photography, streak imaging, filtered photoconducting diodes and x-ray crystal spectroscopy. The source size and distribution are determined through x-ray pinhole photographs. The radiation energy spectrum is determined by x-ray spectroscopy and attenuation through filters. Energy intensities were obtained from the filtered photoconducting diodes

Eigenvalue pinching on spinc manifolds

Science.gov (United States)

Roos, Saskia

2017-02-01

We derive various pinching results for small Dirac eigenvalues using the classification of spinc and spin manifolds admitting nontrivial Killing spinors. For this, we introduce a notion of convergence for spinc manifolds which involves a general study on convergence of Riemannian manifolds with a principal S1-bundle. We also analyze the relation between the regularity of the Riemannian metric and the regularity of the curvature of the associated principal S1-bundle on spinc manifolds with Killing spinors.

Computer simulation of plasma behavior in open-ended linear theta machines. Scientific report 81-5

International Nuclear Information System (INIS)

Stover, E.K.

1981-04-01

Zero-dimensional and one-dimensional fluid plasma computer models have been developed to study the behavior of linear theta pinch plasmas. Computer simulation results generated from these codes are compared with data obtained from two theta pinch experiments so that significant machine plasma behavior can be identified. The experiments examined are a collisional experiment, T/sub i/ approx. 50 eV, n/sub e/ approx. 10 17 cm -3 , where the plasma mean-free-path was significantly less than the plasma column length, and a hot ion species experiment, T/sub i/ approx. 3 keV, n/sub e/ approx. 10 16 cm -3 , where the ion mean-free-path was on the order of the plasma column length

Classical transport in a non-circular z-pinch

International Nuclear Information System (INIS)

Eriksson, G.

1987-05-01

A method is devised, in which particle and heat fluxes are found by solving the heat balance equation self-consistently for specified profiles. The procedure is applied to an equilibrium which corresponds to a non-circular z-pinch. (author)

A novel graphical technique for Pinch Analysis applications: Energy Targets and grassroots design

International Nuclear Information System (INIS)

Gadalla, Mamdouh A.

2015-01-01

Graphical abstract: A new HEN graphical design. - Highlights: • A new graphical technique for heat exchanger networks design. • Pinch Analysis principles and design rules are better interpreted. • Graphical guidelines for optimum heat integration. • New temperature-based graphs provide user-interactive features. - Abstract: Pinch Analysis is for decades a leading tool to energy integration for retrofit and design. This paper presents a new graphical technique, based on Pinch Analysis, for the grassroots design of heat exchanger networks. In the new graph, the temperatures of hot streams are plotted versus those of the cold streams. The temperature–temperature based graph is constructed to include temperatures of hot and cold streams as straight lines, horizontal lines for hot streams, and vertical lines for cold streams. The graph is applied to determine the pinch temperatures and Energy Targets. It is then used to synthesise graphically a complete exchanger network, achieving the Energy Targets. Within the new graph, exchangers are represented by inclined straight lines, whose slopes are proportional to the ratio of heat capacities and flows. Pinch Analysis principles for design are easily interpreted using this new graphical technique to design a complete exchanger network. Network designs achieved by the new technique can guarantee maximum heat recovery. The new technique can also be employed to simulate basic designs of heat exchanger networks. The strengths of the new tool are that it is simply applied using computers, requires no commercial software, and can be used for academic purposes/engineering education

Processes governing pinch formation in diodes

International Nuclear Information System (INIS)

Blaugrund, A.E.; Cooperstein, G.; Goldstein, S.A.

1975-01-01

The process of pinch formation in large aspect ratio diodes has been studied by means of streak photography and time-resolved x-ray detectors. A tight pinch is formed at the anode center by a collapsing thin hollow electron beam. The collapse velocity depends, among other things, on the type of material in the top 1 μm layer of the anode. In a tentative model it is assumed that an anode plasma is at least partially created from gases released from the surface layer of the anode by the heating action of the beam. These gases are ionized by primary, backscattered, and secondary electrons. Ions emitted from this plasma modify the electron trajectories in the diode leading to a radial collapse of the hollow electron beam. The observed monotonic dependence of the collapse velocity on the atomic number of the anode material can be explained by the smooth dependence on Z of both the specific heat and the electron backscatter coefficient. In the case of high-Z anodes the ion expansion time appears to be the factor limiting the collapse velocity. Detailed experimental data are presented

Characterization of diagnostic hole-closure in Z-pinch driven hohlraums

International Nuclear Information System (INIS)

Baker, K. L.; Porter, J. L.; Ruggles, L. E.; Chandler, G. A.; Deeney, Chris; Vargas, M.; Moats, Ann; Struve, Ken; Torres, J.; McGurn, J. S.

2000-01-01

In this article we investigate the partial closure of diagnostic holes in Z-pinch driven hohlraums. These hohlraums differ from current laser-driven hohlraums in a number of ways such as their larger size, greater x-ray drive energy, and lower temperature. Although the diameter of the diagnostic holes on these Z-pinch driven hohlraums can be much greater than their laser-driven counterparts, 4 mm in diameter or larger, radiation impinges on the wall material surrounding the hole for the duration of the Z pinch, nearly 100 ns. This incident radiation causes plasma to ablate from the hohlraum walls surrounding the diagnostic hole and partially obscure this diagnostic hole. This partial obscuration reduces the effective area over which diagnostics view the hohlraum's radiation. This reduction in area can lead to an underestimation of the wall temperature when nonimaging diagnostics such as x-ray diodes and bolometers are used to determine power and later to infer a wall temperature. In this article we describe the techniques used to characterize the hole-closure in these hohlraums and present the experimental measurements of this process. (c) 2000 American Institute of Physics

Characterization of diagnostic hole-closure in Z-pinch driven hohlraums

Energy Technology Data Exchange (ETDEWEB)

Baker, K. L. [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); Porter, J. L. [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); Ruggles, L. E. [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); Chandler, G. A. [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); Deeney, Chris [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); Vargas, M. [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); Moats, Ann [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); Struve, Ken [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); Torres, J. [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States); McGurn, J. S. [Sandia National Laboratory, Albuquerque, New Mexico 87185 (United States)] (and others)

2000-02-01

In this article we investigate the partial closure of diagnostic holes in Z-pinch driven hohlraums. These hohlraums differ from current laser-driven hohlraums in a number of ways such as their larger size, greater x-ray drive energy, and lower temperature. Although the diameter of the diagnostic holes on these Z-pinch driven hohlraums can be much greater than their laser-driven counterparts, 4 mm in diameter or larger, radiation impinges on the wall material surrounding the hole for the duration of the Z pinch, nearly 100 ns. This incident radiation causes plasma to ablate from the hohlraum walls surrounding the diagnostic hole and partially obscure this diagnostic hole. This partial obscuration reduces the effective area over which diagnostics view the hohlraum's radiation. This reduction in area can lead to an underestimation of the wall temperature when nonimaging diagnostics such as x-ray diodes and bolometers are used to determine power and later to infer a wall temperature. In this article we describe the techniques used to characterize the hole-closure in these hohlraums and present the experimental measurements of this process. (c) 2000 American Institute of Physics.

Compression dynamics of quasi-spherical wire arrays with different linear mass profiles

International Nuclear Information System (INIS)

Mitrofanov, K. N.; Aleksandrov, V. V.; Gritsuk, A. N.; Grabovski, E. V.; Frolov, I. N.; Laukhin, Ya. N.; Oleinik, G. M.; Ol’khovskaya, O. G.

2016-01-01

Results of experimental studies of the implosion of quasi-spherical wire (or metalized fiber) arrays are presented. The goal of the experiments was to achieve synchronous three-dimensional compression of the plasma produced in different regions of a quasi-spherical array into its geometrical center. To search for optimal synchronization conditions, quasi-spherical arrays with different initial profiles of the linear mass were used. The following dependences of the linear mass on the poloidal angle were used: m_l(θ) ∝ sin"–"1θ and m_l(θ) ∝ sin"–"2θ. The compression dynamics of such arrays was compared with that of quasi-spherical arrays without linear mass profiling, m_l(θ) = const. To verify the experimental data, the spatiotemporal dynamics of plasma compression in quasi-spherical arrays was studied using various diagnostics. The experiments on three-dimensional implosion of quasi-spherical arrays made it possible to study how the frozen-in magnetic field of the discharge current penetrates into the array. By measuring the magnetic field in the plasma of a quasi-spherical array, information is obtained on the processes of plasma production and formation of plasma flows from the wire/fiber regions with and without an additionally deposited mass. It is found that penetration of the magnetic flux depends on the initial linear mass profile m_l(θ) of the quasi-spherical array. From space-resolved spectral measurements and frame imaging of plasma X-ray emission, information is obtained on the dimensions and shape of the X-ray source formed during the implosion of a quasi-spherical array. The intensity of this source is estimated and compared with that of the Z-pinch formed during the implosion of a cylindrical array.

Generation of an intense ion beam by a pinched relativistic electron beam

International Nuclear Information System (INIS)

Gilad, P.; Zinamon, Z.

1976-01-01

The pinched electron beam of a pulsed electron accelerator is used to generate an intense beam of ions. A foil anode and vacuum drift tube are used. The space charge field of the pinched beam in the tube accelerates ions from the foil anode. Ion currents of 10 kA at a density of 5kA/cm 2 with pulse length of 50 ns are obtained using a 5 kJ, 450 kV, 3 Ω diode. (author)

Application of 2-D Simulations to Z-Pinch Experiment Design and Analysis

International Nuclear Information System (INIS)

Peterson, D.L.; Bowers, R.L.; Matuska, W.; Chandler, G.A.; Deeney, C.; Derzon, M.S.; Matzen, M.K.; Mock, R.C.; Nash, T.J.; Sanford, T.W.L.; Spielman, R.B.; Struve, K.W.

1998-01-01

The successful 2-D simulations of z-pinch experiments (reproducing such features as the measured experimental current drive, radiation pulse shape, peak power and total radiated energy) can lead to a better understanding of the underlying physics in z-pinch implosions and to the opportunity to use such simulations in the analysis of experimental data and in the design of new experiments. Such use has been made with LANL simulations of experiments on the Sandia Saturn and Z accelerators. Applications have included ''vacuum'' and ''dynamic'' hohlraum experiments; variations in mass, radius and length; and ''nested'' array configurations. Notable examples include the explanation of the power/length results in reduced length pinches and the prediction of the current best power and pulsewidth nested array experiment. Examples of circumstances where the simulation results do not match the experiments will be given along with a discussion of opportunities for improved simulation results

Compressibility Effects in the Dynamics of the Reversed-Field Pinch

International Nuclear Information System (INIS)

Onofri, M.; Malara, F.; Veltri, P.

2008-01-01

We study the reversed-field pinch through the numerical solution of the compressible magnetohydrodynamic equations. Two cases are investigated: In the first case the pressure is derived from an adiabatic condition, and in the second case the pressure equation includes heating terms due to resistivity and viscosity. In the adiabatic case a single helicity state is observed, and the reversed-field pinch configuration is formed for short time intervals and is finally lost. In the nonadiabatic case the system reaches a multiple helicity state, and the reversal parameter remains negative for a longer time. The results show the importance of compressibility in determining the large scale dynamics of the system

Production of ion beam by conical pinched electron beam diode

International Nuclear Information System (INIS)

Matsukawa, Y.; Nakagawa, Y.

1982-01-01

Some properties of the ion beam produced by pinched electron beam diode having conical shape electrodes and organic insulator anode was studied. Ion energy is about 200keV and the peak diode current is about 30 kA. At 11cm from the diode apex, not the geometrical focus point, concentrated ion beam was obtained. Its density is more than 500A/cm 2 . The mean ion current density within the radius of 1.6cm around the axis from conical diode is two or three times that from an usual pinched electron beam diode with flat parallel electrodes of same dimension and impedance under the same conditions. (author)

Pinch-off syndrome: transection of implantable central venous access device.

Science.gov (United States)

Sugimoto, Takuya; Nagata, Hiroshi; Hayashi, Ken; Kano, Nobuyasu

2012-11-30

As the population of people with cancer increases so does the number of patients who take chemotherapy. Majority of them are administered parentally continuously. Implantable central venous catheter device is a good choice for those patients; however, severe complication would occur concerning the devices. Pinch-off syndrome is one of the most severe complications. The authors report a severe case of pinch-off syndrome. The patient with the implantable central venous device could not take chemotherapy because the device occluded. Further examination revealed the transection of the catheter. The transected fragment of the catheter in the heart was successfully removed by using a loop snare placed through the right femoral vein.

Development of global magnetohydrodynamic instabilities in Z-pinch plasmas in the presence of nonideal effects

International Nuclear Information System (INIS)

Sotnikov, V.I.; Bauer, B.S.; Leboeuf, J.N.; Hellinger, P.; Travnicek, P.; Fiala, V.

2004-01-01

The development of global magnetohydrodynamic (MHD) instabilities in Z-pinch plasmas has been studied with a three-dimensional hybrid simulation model. Plasma equilibria without and with axial sheared flow, and with different values of the parameter ε H , which appears as a coefficient before the Hall term in dimensionless nonideal MHD equations, have been considered. Increasing the parameter ε H leads to larger simulation growth rates for both m=0 sausage and m=1 kink modes. The hybrid simulations do however show that axial sheared flow severely curtails the linear and nonlinear development of both sausage and kink instabilities. In these respects, the hybrid simulations are in qualitative agreement with linear Hall MHD results. Moreover, in the nonlinear stage, long wavelength modes dominate the excited wave spectrum when the parameter ε H is small. For the larger value of the parameter ε H , small-scale structures do however develop nonlinearly in the excited wave spectrum at late times

Compact-Toroid fusion reactor based on the field-reversed theta pinch

International Nuclear Information System (INIS)

Hagenson, R.L.; Krakowski, R.A.

1981-03-01

Early scoping studies based on approximate, analytic models have been extended on the basis of a dynamic plasma model and an overall systems approach to examine a Compact Toroid (CTOR) reactor embodiment that uses a Field-Reversed Theta Pinch as a plasma source. The field-reversed plasmoid would be formed and compressionally heated to ignition prior to injection into and translation through a linear burn chamber, thereby removing the high-technology plasmoid source from the hostile reactor environment. Stabilization of the field-reversed plasmoid would be provided by a passive conducting shell located outside the high-temperature blanket but within the low-field superconducting magnets and associated radiation shielding. On the basis of this batch-burn but thermally steady-state approach, a reactor concept emerges with a length below approx. 40 m that generates 300 to 400 MWe of net electrical power with a recirculating power fraction less than 0.15

D-D fusion experiments using fast z pinches

International Nuclear Information System (INIS)

Spielman, R.B.; Baldwin, G.T.; Cooper, G.

1994-01-01

The development of high current (I > 10 MA) drivers provides us with a new tool for the study of neutron-producing plasmas in the thermal regime. The imploded deuterium mass (or collisionality) increases as I 2 and the ability of the driver to heat the plasma to relevant fusion temperatures improves as the power of the driver increases. Additionally, fast ( 2 fiber arrays were imploded in a fast z-pinch configuration on Sandia's Saturn facility generating up to 3 x 10 12 D-D neutrons. These experiments were designed to explore the physics of neutron-generating plasmas in a z-pinch geometry. Specifically, we intended to produce neutrons from a nearly thermal plasma where the electrons and ions have a nearly Maxwellian distribution. This is to be clearly differentiated from the more usual D-D beam-target neutrons generated in many dense plasma focus (DPF) devices

D-D fusion experiments using fast Z pinches

International Nuclear Information System (INIS)

Spielman, R.B.; Baldwin, G.T.; Cooper, G.

1998-03-01

The development of high current (I > 10 MA) drivers provides the authors with a new tool for the study of neutron-producing plasmas in the thermal regime. The imploded deuterium mass (or collisionality) increases as I 2 and the ability of the driver to heat the plasma to relevant fusion temperatures improves as the power of the driver increases. Additionally, fast ( 2 fiber arrays were imploded in a fast z-pinch configuration on Sandia's Saturn facility generating up to 3 x 10 12 D-D neutrons. These experiments were designed to explore the physics of neutron-generating plasmas in a z-pinch geometry. Specifically, the authors intended to produce neutrons from a nearly thermal plasma where the electrons and ions have a nearly Maxwellian distribution. This is to be clearly differentiated from the more usual D-D beam-target neutrons generated in many dense plasma focus (DPF) devices

Mechanism of soft x-ray continuum radiation from low-energy pinch discharges of hydrogen and ultra-low field ignition of solid fuels

Science.gov (United States)

Mills, R.; Lotoski, J.; Lu, Y.

2017-09-01

EUV continuum radiation (10-30 nm) arising only from very low energy pulsed pinch gas discharges comprising some hydrogen was first observed at BlackLight Power, Inc. and reproduced at the Harvard Center for Astrophysics (CfA). The source was determined to be due to the transition of H to the lower-energy hydrogen or hydrino state H(1/4) whose emission matches that observed wherein alternative sources were eliminated. The identity of the catalyst that accepts 3 · 27.2 eV from the H to cause the H to H(1/4) transition was determined to HOH versus 3H. The mechanism was elucidated using different oxide-coated electrodes that were selective in forming HOH versus plasma forming metal atoms as well as from the intensity profile that was a mismatch for the multi-body reaction required during 3H catalysis. The HOH catalyst was further shown to give EUV radiation of the same nature by igniting a solid fuel comprising a source of H and HOH catalyst by passing a low voltage, high current through the fuel to produce explosive plasma. No chemical reaction can release such high-energy light. No high field existed to form highly ionized ions that could give radiation in this EUV region that persisted even without power input. This plasma source serves as strong evidence for the existence of the transition of H to hydrino H(1/4) by HOH as the catalyst and a corresponding new power source wherein initial extraordinarily brilliant light-emitting prototypes are already producing photovoltaic generated electrical power. The hydrino product of a catalyst reaction of atomic hydrogen was analyzed by multiple spectroscopic techniques. Moreover, the mH catalyst was identified to be active in astronomical sources such as the Sun, stars and interstellar medium wherein the characteristics of hydrino match those of the dark matter of the Universe.

Grip and Pinch Strength Norms for Michigan Workers

Directory of Open Access Journals (Sweden)

Joel M. Phillips M.S., OTRL

2013-06-01

Full Text Available The purpose of this study was to create a norm reference of current grip and pinch strength norms for working-age Michigan adults. This normative study included a convenience sample of 179 volunteers who were employees at car plants in South East Michigan or hospital sites in West Michigan. Participants’ ages ranged from between 20 and 62 years of age with a mean age of 49.15 years. There were 78 females (44% and 101 males (56%. Subjects were classified by gender and in the age categories of ages 20 to 49 years and ages 50-62 years. Grip and pinch strength norms were collected following the American Society of Hand Therapy protocol. The norms from these working adults were calculated with descriptive statistics for males and females in two age classifications: ages 20 to 49 and ages 50 to 62 years. Standard Errors (SE are better than the 1985 norms for both males and females ages 20 to 49 years. SEs are higher than the ages 20 to 49 years’ norms for the ages 50 to 62 years age categories in both males and females. These norms offer a point of comparison for clinicians to use for clients in Michigan who are ages 20 to 62 years and who have a goal to improve their grip strength. Clients’ grip and pinch strength could be compared to their age level or gender norms using the comparison for one standard deviation above, below, or at the means.

Method and apparatus for producing average magnetic well in a reversed field pinch

International Nuclear Information System (INIS)

Ohkawa, T.

1983-01-01

A magnetic well reversed field plasma pinch method and apparatus produces hot magnetically confined pinch plasma in a toroidal chamber having a major toroidal axis and a minor toroidal axis and a small aspect ratio, e.g. < 6. A pinch current channel within the plasma and at least one hyperbolic magnetic axis outside substantially all of the plasma form a region of average magnetic well in a region surrounding the plasma current channel. The apparatus is operated so that reversal of the safety factor q and of the toroidal magnetic field takes place within the plasma. The well-producing plasma cross section shape is produced by a conductive shell surrounding the shaped envelope and by coils. A shell is of copper or aluminium with non-conductive breaks, and is bonded to a thin aluminium envelope by silicone rubber. (author)

Pinching Solutions of Slender Cylindrical Jets

Science.gov (United States)

1993-06-01

NASA Langley Research Center, Hampton, VA 23681.2This research was supported in part by Fondo Nacional de Desarrollo Cientifico y Tecnologico (FONDE...concentrate on inviscid irrotational flows of liquid jets. A review article has been written by Bogy [2]. Of relevance is also the work of Chandrasekhar...equations become elliptic and allow the possibility of admissible pinching solutions described in this article . It is interesting to find that for jets

Predicting tile drainage discharge

DEFF Research Database (Denmark)

Iversen, Bo Vangsø; Kjærgaard, Charlotte; Petersen, Rasmus Jes

used in the analysis. For the dynamic modelling, a simple linear reservoir model was used where different outlets in the model represented tile drain as well as groundwater discharge outputs. This modelling was based on daily measured tile drain discharge values. The statistical predictive model...... was based on a polynomial regression predicting yearly tile drain discharge values using site specific parameters such as soil type, catchment topography, etc. as predictors. Values of calibrated model parameters from the dynamic modelling were compared to the same site specific parameter as used...

A conceptual fusion reactor based on the high-plasma-density Z-pinch

International Nuclear Information System (INIS)

Hartman, C.W.; Carlson, G.; Hoffman, M.; Werner, R.

1977-01-01

Conceptual DT and DD fusion reactors are discussed based on magnetic confinement with the high-plasma-density Z-pinch. The reactor concepts have no ''first wall'', the fusion neutrons and plasma energy being absorbed directly into a surrounding lithium vortex blanket. Efficient systems with low re-circulated power are projected, based on a flow-through pinch cycle for which overall Q values can approach 10. The conceptual reactors are characterized by simplicity, small minimum size (100MW(e)) and by the potential for minimal radioactivity hazards. (author)

A new graphical method for Pinch Analysis applications: Heat exchanger network retrofit and energy integration

International Nuclear Information System (INIS)

Gadalla, Mamdouh A.

2015-01-01

Energy integration is a key solution in chemical process and crude refining industries to minimise external fuel consumption and to face the impact of growing energy crises. Typical energy integration projects can reach a reduction of heating fuels and cold utilities by up to 40% compared with original designs or existing installations. Pinch Analysis is a leading tool and regarded as an efficient method to increase energy efficiency and minimise fuel flow consumptions. It is valid for both natures of design, grassroots and retrofit situations. It can practically be applied to synthesise a HEN (heat exchanger network) or modify an existing preheat train for minimum energy consumption. Heat recovery systems or HENs are networks for exchanging heat between hot and cold process sources. All heat transferred from hot process sources into cold process sinks represent the scope for energy integration. On the other hand, energies required beyond this integrated amount are to be satisfied by external utilities. Graphical representations of Pinch Analysis, such as Composite and Grand Composite Curves are very useful for grassroots designs. Nevertheless, in retrofit situation the analysis is not adequate and besides it is graphically tedious to represent existing exchangers on such graphs. This research proposes a new graphical method for the analysis of heat recovery systems, applicable to HEN retrofit. The new graphical method is based on plotting temperatures of process hot streams versus temperatures of process cold streams. A new graph is constructed for representing existing HENs. For a given network, each existing exchanger is represented by a straight line, whose slope is proportional to the ratio of heat capacities and flows. Further, the length of each exchanger line is related to the heat flow transferred across this exchanger. This new graphical representation can easily identify exchangers across the pinch, Network Pinch, pinching matches and improper placement

Computer simulation of plasma behavior in open-ended linear theta machines. Scientific report 81-5

Energy Technology Data Exchange (ETDEWEB)

Stover, E. K.

1981-04-01

Zero-dimensional and one-dimensional fluid plasma computer models have been developed to study the behavior of linear theta pinch plasmas. Computer simulation results generated from these codes are compared with data obtained from two theta pinch experiments so that significant machine plasma behavior can be identified. The experiments examined are a collisional experiment, T/sub i/ approx. 50 eV, n/sub e/ approx. 10/sup 17/ cm/sup -3/, where the plasma mean-free-path was significantly less than the plasma column length, and a hot ion species experiment, T/sub i/ approx. 3 keV, n/sub e/ approx. 10/sup 16/ cm/sup -3/, where the ion mean-free-path was on the order of the plasma column length.

Moderately reverberant learning ultrasonic pinch panel.

Science.gov (United States)

Nikolovski, Jean-Pierre

2013-10-01

Tactile sensing is widely used in human-computer interfaces. However, mechanical integration of touch technologies is often perceived as difficult by engineers because it often limits the freedom of style or form factor requested by designers. Recent work in active ultrasonic touch technologies has made it possible to transform thin glass plates, metallic sheets, or plastic shells into interactive surfaces. The method is based on a learning process of touch-induced, amplitude-disturbed diffraction patterns. This paper proposes, first, an evolution in the design with multiple dipole transducers that improves touch sensitivity or maximum panel size by a factor of ten, and improves robustness and usability in moderately reverberant panels, and second, defines a set of acoustic variables in the signal processing for the evaluation of sensitivity and radiating features. For proof of concept purposes, the design and process are applied to 3.2- and 6-mm-thick glass plates with variable damping conditions. Transducers are bonded to only one short side of the rectangular substrates. Measurements show that the highly sensitive free lateral sides are perfectly adapted for pinch-touch and pinch-slide interactions. The advantage of relative versus absolute touch disturbance measurement is discussed, together with tolerance to abutting contaminants.

Particle pinch with fully noninductive lower hybrid current drive in Tore Supra.

Science.gov (United States)

Hoang, G T; Bourdelle, C; Pégourié, B; Schunke, B; Artaud, J F; Bucalossi, J; Clairet, F; Fenzi-Bonizec, C; Garbet, X; Gil, C; Guirlet, R; Imbeaux, F; Lasalle, J; Loarer, T; Lowry, C; Travère, J M; Tsitrone, E

2003-04-18

Recently, plasmas exceeding 4 min have been obtained with lower hybrid current drive (LHCD) in Tore Supra. These LHCD plasmas extend for over 80 times the resistive current diffusion time with zero loop voltage. Under such unique conditions the neoclassical particle pinch driven by the toroidal electric field vanishes. Nevertheless, the density profile remains peaked for more than 4 min. For the first time, the existence of an inward particle pinch in steady-state plasma without toroidal electric field, much larger than the value predicted by the collisional neoclassical theory, is experimentally demonstrated.

Pinch technology in theory and its application to a biomass integrated gasification and humid air turbine process

Energy Technology Data Exchange (ETDEWEB)

Garcia, B.L.

1998-03-01

The Pinch Technology has become a powerful tool for the optimization of the design of heat exchanger networks during the last 20 years. In this work, the different aspects of the methodology have been studied both in a theoretical way and in a practical approach. The first part of the work is a systematic analysis of the pinch technology: what it is, how it works, what are its advantages and disadvantages. There is also a brief discussion about the pinch method and other methods which handle energy recovery problems. Once the philosophy of the pinch technology has been theoretically studied, the second part of the work is its application to two different processes. The first process analyzed is a relatively simple but realistically practical problem based on a two distillation columns system. The knowledge gained during the calculations of this process is used in the second and more complex one. This second process is an integrated biomass gasification and humid air turbine (IGHAT) which has been already optimized by a heat balance program. The application of the pinch technology to this process shows the huge potential for improvements that this technology can provide in order to save energy. All the calculations are handled by the pinch technology software program `SuperTarget`. This program is evaluated along the work. In spite of some shortcomings that have been noticed, the usefulness of the program can be claimed 26 refs, 28 figs, 7 tabs

Research on pinches driven by Speed-2 generator: Hard X-ray and neutron emission in plasma focus configuration

Energy Technology Data Exchange (ETDEWEB)

Soto, L.; Moreno, J.; Silva, P.; Sylvester, G.; Zambra, M.; Pavez, C. [Comision Chilena de Energia Nuclear, Santiago (Chile); Pavez, C. [Universidad de Concepcion (Chile); Raspa, V. [Buenos Aires Univ., PLADEMA, CONICET and INFIP (Argentina); Castillo, F. [Insitituto de Ciencias Nucleares, UNAM (Mexico); Kies, W. [Heinrich-Heine-Univ., Dusseldorf (Germany)

2004-07-01

Speed-2 is a generator based on Marx technology and was designed in the University of Dusseldorf. Speed-2 consists on 40 +/- Marx modules connected in parallel (4.1 {mu}F equivalent Marx generator capacity, 300 kV, 4 MA in short circuit, 187 kJ, 400 ns rise time, dI/dt {approx} 10{sup 13} A/s). Currently Speed-2 is operating at CCHEN (Chilean nuclear energy commission), being the most powerful and energetic device for dense transient plasma in the Southern Hemisphere. Most of the previous works developed in Speed-2 at Dusseldorf were done in a plasma focus configuration for soft X-ray emission and the neutron emission from Speed-2 was not completely studied. The research program at CCHEN considers experiments in different pinch configurations (plasma focus, gas puffed plasma focus, gas embedded Z-pinch, wire arrays) at current of hundred of kilo- to mega-amperes, using the Speed-2 generator. The Chilean operation has begun implementing and developing diagnostics in a conventional plasma focus configuration operating in deuterium in order to characterize the neutron emission and the hard X-ray production. Silver activation counters, plastics CR39 and scintillator-photomultiplier detectors are used to characterize the neutron emission. Images of metallic plates with different thickness are obtained on commercial radiographic film, Agfa Curix ST-G2, in order to characterize an effective energy of the hard X-ray outside of the discharge. (authors)

On finite larmor radius stabilization of Z-pinches

International Nuclear Information System (INIS)

Hellsten, T.

1982-12-01

Finite Larmor radius stabilization of Z-pinches is discussed. Stability criteria can be derived for a class of equilibria having constant mass and current density. The internal modes can be stabilized provided the line density not exceed a critical value of the order of 10 18 ions/m. (Author)

Tungsten Z-Pinch Long Implosions on the Saturn Generator

International Nuclear Information System (INIS)

DOUGLAS, MELISSA R.; DEENEY, Christopher; SPIELMAN, RICK B.; COVERDALE, CHRISTINE A.; RODERICK, N.F.; HAINES, M.G.

1999-01-01

Recent success on the Saturn and Z accelerators at Sandia National Laboratories have demonstrated the ability to scale z-pinch parameters to increasingly larger current pulsed power facilities. Next generation machines will require even larger currents (>20 MA), placing further demands on pulsed power technology. To this end, experiments have been carried out on Saturn operating in a long pulse mode, investigating the potential of lower voltages and longer implosion times while still maintaining pinch fidelity. High wire number, 25 mm diameter tungsten arrays were imploded with implosion times ranging from 130 to 240 ns. The results were comparable to those observed in the Saturn short pulse mode, with risetimes on the order of 4.5 to 6.5 ns. Experimental data will be presented, along with two dimensional radiation magnetohydrodynamic simulations used to explain and reproduce the experiment

Compact-Toroid Fusion Reactor (CTOR) based on the Field-Reversed Theta Pinch

International Nuclear Information System (INIS)

Hagenson, R.L.; Krakowski, R.A.

1981-01-01

Scoping studies of a translating Compact Torus Reactor (CTOR) have been made on the basis of a dynamic plasma model and an overall systems approach. This CTOR embodiment uses a Field-Reversed Theta Pinch as a plasma source. The field-reversed plasmoid would be formed and compressionally heated to ignition prior to injection into and translation through a linear burn chamber, thereby removing the high-technology plamoid source from the hostile reactor environment. Stabilization of the field-reversed plasmoid would be provided by a passive conducting shell located outside the high-temperature blanket but within the low-field superconducting magnets and associated radition shielding. On the basis of this batch-burn but thermally steady-state approach, a reactor concept emerges with a length below approx. 40 m that generates 300 to 400 MWe of net electrical power with a recirculating power fraction less than 0.15

Modeling x-ray data for the Saturn z-pinch machine

International Nuclear Information System (INIS)

Matuska, W.; Peterson, D.; Deeney, C.; Derzon, M.

1997-01-01

A wealth of XRD and time dependent x-ray imaging data exist for the Saturn z-pinch machine, where the load is either a tungsten wire array or a tungsten wire array which implodes onto a SiO 2 foam. Also, these pinches have been modeled with a 2-D RMHD Eulerian computer code. In this paper the authors start with the 2-D Eulerian results to calculate time and spatially dependent spectra using both LTE and NLTE models. Then using response functions, these spectra are converted to XRD currents and camera images, which are quantitatively compared with the data. Through these comparisons, areas of good and lesser quality agreement are determined, and areas are identified where the 2-D Eulerian code should be improved

X-Pinch Plasma Generation Testing for Neutron Source Development and Nuclear Fusion

Directory of Open Access Journals (Sweden)

Hossam A.Gabbar

2018-04-01

Full Text Available Nuclear fusion is a sought-out technology in which two light elements are fused together to create a heavier element and releases energy. Two primary nuclear fusion technologies are being researched today: magnetic and inertial confinement. However, a new type of nuclear fusion technology is currently being research: multi-pinch plasma beams. At the University of Ontario Institute of Technology, there is research on multi-pinch plasma beam technology as an alternative to nuclear fusion. The objective is to intersect two plasma arcs at the center of the chamber. This is a precursor of nuclear fusion using multi-pinch. The innovation portion of the students’ work is the miniaturization of this concept using high energy electrical DC pulses. The experiment achieved the temperature of 2300 K at the intersection. In comparison to the simulation data, the temperature from the simulation is 7000 K at the intersection. Additionally, energy harvesting devices, both photovoltaics and a thermoelectric generator, were placed in the chamber to observe the viable energy extraction.

Wire-number effects on high-power annular z-pinches and some characteristics at high wire number

Energy Technology Data Exchange (ETDEWEB)

SANFORD,THOMAS W. L.

2000-05-23

Characteristics of annular wire-array z-pinches as a function of wire number and at high wire number are reviewed. The data, taken primarily using aluminum wires on Saturn are comprehensive. The experiments have provided important insights into the features of wire-array dynamics critical for high x-ray power generation, and have initiated a renaissance in z-pinches when high numbers of wires are used. In this regime, for example, radiation environments characteristic of those encountered during the early pulses required for indirect-drive ICF ignition on the NIF have been produced in hohlraums driven by x-rays from a z-pinch, and are commented on here.

Wire-number effects on high-power annular z-pinches and some characteristics at high wire number

International Nuclear Information System (INIS)

SANFORD, THOMAS W. L.

2000-01-01

Characteristics of annular wire-array z-pinches as a function of wire number and at high wire number are reviewed. The data, taken primarily using aluminum wires on Saturn are comprehensive. The experiments have provided important insights into the features of wire-array dynamics critical for high x-ray power generation, and have initiated a renaissance in z-pinches when high numbers of wires are used. In this regime, for example, radiation environments characteristic of those encountered during the early pulses required for indirect-drive ICF ignition on the NIF have been produced in hohlraums driven by x-rays from a z-pinch, and are commented on here

More efficient mushroom canning through pinch and exergy analysis

NARCIS (Netherlands)

Paudel, Ekaraj; Sman, van der Ruud G.M.; Westerik, Nieke; Awasthi, Ashutosh; Dewi, Belinda P.C.; Boom, Remko M.

2017-01-01

Conventional production of canned mushrooms involves multiple processing steps as vacuum hydration, blanching, sterilization, etc. that are intensive in energy and water usage. We analyzed the current mushroom processing technique plus three alternative scenarios via pinch and exergy analysis.

Electrical insulators for the theta-pinch fusion reactor

International Nuclear Information System (INIS)

Clinard, F.W. Jr.

1976-01-01

The five major applications for electrical insulators in the Reference Theta Pinch Reactor are as follows: (1) first-wall insulator, (2) blanket intersegment insulator, (3) graphite encapsulating insulator, (4) implosion coil insulator, and (5) compression coil insulator. Insulator design proposals and some preliminary test results are given for each application

Nonlinear dynamics of tearing modes in the reversed field pinch

International Nuclear Information System (INIS)

Holmes, J.A.; Carreras, B.A.; Diamond, P.H.; Lynch, V.E.

1987-05-01

The results of investigations of nonlinear tearing-mode dynamics in reversed field pinch plasmas are described. The linear instabilities have poloidal mode number m = 1 and toroidal mode numbers 10 ≤ n ≤ 20, and the resonant surfaces are therefore in the plasma core. The nonlinear dynamics result in dual cascade processes. The first process is a rapid m = 1 spectral broadening toward high n, with a simultaneous spreading of magnetic turbulence radially outward toward the field-reversal surface. Global m = 0 perturbations, which are driven to large amplitudes by the m = 1 instabilities, in turn trigger the m = 1 spectral broadening by back-coupling to the higher n. The second process is a cascade toward large m and is mediated by m = 2 modes. The m = 2 perturbations have the structure of localized, driven current sheets and nonlinearly stabilize the m = 1 modes by transferring m = 1 energy to small-scale dissipation. The calculated spectrum has many of the qualitative features observed in experiments. 13 refs., 21 figs., 1 tab

On the zero-bias anomaly and Kondo physics in quantum point contacts near pinch-off.

Science.gov (United States)

Xiang, S; Xiao, S; Fuji, K; Shibuya, K; Endo, T; Yumoto, N; Morimoto, T; Aoki, N; Bird, J P; Ochiai, Y

2014-03-26

We investigate the linear and non-linear conductance of quantum point contacts (QPCs), in the region near pinch-off where Kondo physics has previously been connected to the appearance of the 0.7 feature. In studies of seven different QPCs, fabricated in the same high-mobility GaAs/AlGaAs heterojunction, the linear conductance is widely found to show the presence of the 0.7 feature. The differential conductance, on the other hand, does not generally exhibit the zero-bias anomaly (ZBA) that has been proposed to indicate the Kondo effect. Indeed, even in the small subset of QPCs found to exhibit such an anomaly, the linear conductance does not always follow the universal temperature-dependent scaling behavior expected for the Kondo effect. Taken collectively, our observations demonstrate that, unlike the 0.7 feature, the ZBA is not a generic feature of low-temperature QPC conduction. We furthermore conclude that the mere observation of the ZBA alone is insufficient evidence for concluding that Kondo physics is active. While we do not rule out the possibility that the Kondo effect may occur in QPCs, our results appear to indicate that its observation requires a very strict set of conditions to be satisfied. This should be contrasted with the case of the 0.7 feature, which has been apparent since the earliest experimental investigations of QPC transport.

Electrostatic turbulence in the Z pinch corona

International Nuclear Information System (INIS)

Terry, R.E.

1994-01-01

The microstability of electrostatic waves in the periphery of a Z pinch is formulated and resolved for a new class of Vlasov meta-equilibria admitting self-similar solutions in the electron gyrokinetic limit. These equilibria are subject to strong radial motions, and a mild deviation from charge neutrality arises to maintain ion acceleration close to that of the magnetized electrons. A unique class of profiles in density, axial current, temperature, and drift speed defines these equilibria. They are characterized by (i) the interior pinch current, (ii) the interior number density, (iii) the parallel and perpendicular temperatures, (iv) the exterior axial electric field value at the initial time, and (v) the radial ion acceleration relative to that of the electrons. Unstable ion sound waves arise in this medium by coupling radial and axial free energy to azimuthal longitudinal oscillations. The waves grow only for a limited range of radial or axial Exb/B drift speeds and electron temperatures. The growth rate, which can be as large as 0.115ω pi , is found to scale proportional to plasma frequency over the density range from 10 12 to 10 18 ions cm -3

Parameter scaling toward high-energy density in a quasi-steady flow Z-pinch

Science.gov (United States)

Hughes, M. C.; Shumlak, U.; Nelson, B. A.; Golingo, R. P.; Claveau, E. L.; Doty, S. A.; Forbes, E. G.; Kim, B.; Ross, M. P.

2016-10-01

Sheared axial flows are utilized by the ZaP Flow Z-Pinch Experiment to stabilize MHD instabilities. The pinches formed are 50 cm long with radii ranging from 0.3 to 1.0 cm. The plasma is generated in a coaxial acceleration region, similar to a Marshall gun, which provides a steady supply of plasma for approximately 100 us. The power to the plasma is partially decoupled between the acceleration and pinch assembly regions through the use of separate power supplies. Adiabatic scaling of the Bennett relation gives targets for future devices to reach high-energy density conditions or fusion reactors. The applicability of an adiabatic assumption is explored and work is done experimentally to clarify the plasma compression process, which may be more generally polytropic. The device is capable of a much larger parameter space than previous machine iterations, allowing flexibility in the initial conditions of the compression process to preserve stability. This work is supported by DoE FES and NNSA.

ZAPP: Z-pinch atomic physics program

International Nuclear Information System (INIS)

Reed, K.

1983-01-01

High-density and high-temperature plasmas have been produced in a z-pinch with a hollow gas puff. A number of interesting atomic-physics phenomena occur in these plasmas and some of these phenomena provide important diagnostic information for characterizing the plasmas. We have been interested in collisions of high-energy electrons with highly stripped ions in these plasmas. Such collisions may produce a population inversion which could result in stimulated emission in the x-ray regime

Turbulent transport in reversed field pinches

International Nuclear Information System (INIS)

Christiansen, J.P.; Roberts, K.V.

1976-01-01

MHD stability of the Reversed Field Pinch (RFP) relies on reversal of the toroidal field component in the outer plasma region. Interest in this configuration comes from its potential economic advantages as a thermonuclear reactor, since compared to a Tokamak the RFP supports a higher value of β, the ratio between plasma and total magnetic pressure. Results of computations on the time-evolution of the RFP using a 1D MHD model are reported. (orig./GG) [de

Use of Z pinch radiation sources for high pressure shock wave studies

International Nuclear Information System (INIS)

Asay, J.R.; Konrad, C.H.; Hall, C.A.; Trott, W.M.; Chandler, G.A.; Holland, K.G.; Fleming, K.J.; Trucano, T.G.

1998-01-01

Recent developments in pulsed power technology demonstrate use of intense radiation sources (Z pinches) for driving planar shock waves in samples with spatial dimensions larger than possible with other radiation sources. Initial indications are that the use of Z pinch sources can be used to produce planar shock waves in samples with diameters of a few millimeters and thicknesses approaching one half millimeter. These dimensions allow increased accuracy of both shock velocity and particle velocity measurements. The Z pinch radiation source uses imploding metal plasma induced by self-magnetic fields applied to wire arrays to produce high temperature x-ray environments in vacuum hohlraum enclosures. Previous experiments have demonstrated that planar shock waves can be produced with this approach. A photograph of a wire array located inside the vacuum hohlraum is shown here. Typically, a few hundred individual wires are used to produce the Z pinch source. For the shock wave experiments being designed, arrays of 120 to 240 tungsten wires with a diameter of 40 mm and with individual diameters of about 10 microm are used. Preliminary experiments have been performed on the Z pulsed radiation source to demonstrate the ability to obtain VISAR measurements in the Z accelerator environment. Analysis of these results indicate that another effect, not initially anticipated, is an apparent change in refractive index that occurs in the various optical components used in the system. This effect results in an apparent shift in the frequency of reflected laser light, and causes an error in the measured particle velocity. Experiments are in progress to understand and minimize this effect

Reversed field pinch diagnostics

International Nuclear Information System (INIS)

Weber, P.G.

1986-01-01

The Reversed Field Pinch (RFP) is a toroidal, axisymmetric magnetic confinement configuration characterized by a magnetic field configuration in which the toroidal magnetic field is of similar strength to the poloidal field, and is reversed at the edge compared to the center. The RFP routinely operates at high beta, and is a strong candidate for a compact fusion device. Relevant attributes of the configuration will be presented, together with an overview of present and planned experiments and their diagnostics. RFP diagnostics are in many ways similar to those of other magnetic confinement devices (such as tokamaks); these lectures will point out pertinent differences, and will present some diagnostics which provide special insights into unique attributes of the RFP

Self-similar oscillations of a Z pinch

International Nuclear Information System (INIS)

Felber, F.S.

1982-01-01

A new analytic, self-similar solution of the equations of ideal magnetohydrodynamics describes cylindrically symmetric plasmas conducting constant current. The solution indicates that an adiabatic Z pinch oscillates radially with a period typically of the order of a few acoustic transit times. A stability analysis, which shows the growth rate of the sausage instability to be a saturating function of wavenumber, suggests that the oscillations are observable

Computational investigation of single mode vs multimode Rayleigh endash Taylor seeding in Z-pinch implosions

International Nuclear Information System (INIS)

Douglas, M.R.; Deeney, C.; Roderick, N.F.

1998-01-01

A series of two-dimensional magnetohydrodynamic calculations have been carried out to investigate single and multimode growth and mode coupling for magnetically-driven Rayleigh endash Taylor instabilities in Z pinches. Wavelengths ranging from 5.0 mm down to 1.25 mm were considered. Such wavelengths are comparable to those observed at stagnation using a random density open-quotes seedingclose quotes method. The calculations show that wavelengths resolved by less than 10 cells exhibit an artificial decrease in initial Fourier spectrum amplitudes and a reduction in the corresponding amplitude growth. Single mode evolution exhibits linear exponential growth and the development of higher harmonics as the mode transitions into the nonlinear phase. The mode growth continues to exponentiate but at a slower rate than determined by linear hydrodynamic theory. In the two and three mode case, there is clear evidence of mode coupling and inverse cascade. In addition, distinct modal patterns are observed late in the implosion, resulting from finite shell thickness and magnetic field effects. copyright 1998 American Institute of Physics. thinsp

Radiation symmetry control for inertial confinement fusion capsule implosions in double Z-pinch hohlraums on Z

International Nuclear Information System (INIS)

Vesey, Roger A.; Cuneo, Michael E.; Porter, John L. Jr.; Adams, Richard G.; Aragon, Rafael A.; Rambo, Patrick K.; Ruggles, Laurence E.; Simpson, Walter W.; Smith, Ian C.; Bennett, Guy R.

2003-01-01

The double Z-pinch hohlraum high-yield concept [Hammer et al., Phys. Plasmas 6, 2129 (1999)] utilizes two 63-MA Z pinches to heat separate primary hohlraums at either end of a secondary hohlraum containing the cryogenic fusion capsule. Recent experiments on the Z accelerator [Spielman et al., Phys. Plasmas 5, 2105 (1998)] at Sandia National Laboratories have developed an advanced single-sided power feed, double Z-pinch load to study radiation symmetry and pinch power balance using implosion capsules [Cuneo et al., Phys. Rev. Lett. 88, 215004 (2002)]. Point-projection x-ray imaging with the Z-Beamlet Laser mapped the trajectory and distortion of 2-mm diameter plastic ablator capsules. Using the backlit capsule distortion as a symmetry diagnostic, the ability to predictably tune symmetry at the 2 Legendre mode asymmetry coefficient over a range of ±6% (±2% considering points nearest the optimum) was achieved by varying the length of the cylindrical secondary hohlraum containing the capsule, in agreement with viewfactor and radiation-hydrodynamics simulations

Nonlinear full two-fluid study of m=0 sausage instabilities in an axisymmetric Z pinch

International Nuclear Information System (INIS)

Loverich, J.; Shumlak, U.

2006-01-01

A nonlinear full five-moment two-fluid model is used to study axisymmetric instabilities in a Z pinch. When the electron velocity due to the current J is greater than the ion acoustic speed, high wave-number sausage instabilities develop that initiate shock waves in the ion fluid. This condition corresponds to a pinch radius on the order of a few ion Larmor radii

Current-driven instabilities of the kinetic shear Alfven wave: Application to reversed field pinches and spheromaks

International Nuclear Information System (INIS)

Meyerhofer, D.D.; Perkins, F.W.

1984-01-01

The kinetic Alfven wave is studied in a cylindrical force-free plasma with self-consistent magnetic fields. This equilibrium represents a reversed field pinch or a spheromak. The stability of the wave is found to depend on the ratio of the electron drift velocity to the Alfven velocity. This ratio varies inversely with the square root of the plasma line density. The critical line density using the Spitzer--Harm electron distribution function is found for reversed field pinches with deuterium plasmas to be approximately 2 x 10 18 and is 5 x 10 17 m -1 in spheromaks with hydrogen plasmas. The critical line density is in reasonable agreement with experimental data for reversed field pinches

Current driven instabilities of the kinetic shear Alfven wave: application to reversed field pinches and spheromaks

International Nuclear Information System (INIS)

Meyerhofer, D.D.; Perkins, F.W.

1984-04-01

The kinetic Alfven wave is studied in a cylindrical force-free plasma with self-consistent magnetic fields. This equilibrium represents a reversed field pinch or a spheromak. The stability of the wave is found to depend on the ratio of the electron drift velocity to the Alfven velocity. This ratio varies inversely with the square root of the plasma line density. The critical line density using the Spitzer-Harm electron distribution function is found for reversed field pinches with deuterium plasmas to be approximately 2 x 10 18 m -1 and is 5 x 10 17 m -1 in spheromaks with hydrogen plasmas. The critical line density is in reasonable agreement with experimental data for reversed field pinches