The effect of various pozzolanic additives on the concrete strength index

Science.gov (United States)

Vitola, L.; Sahmenko, G.; Erdmane, D.; Bumanis, G.; Bajare, D.

2017-10-01

The concrete industry is searching continuously for new effective mineral additives to improve the concrete properties. Replacing cement with the pozzolanic additives in most cases has resulted not only in positive impact on the environment but also has improved strength and durability of the concrete. Effective pozzolanic additives can be obtained from natural resources such as volcanic ashes, kaolin and other sediments as well as from different production industries that create various by-products with high pozzolanic reactivity. Current research deals with effectiveness evaluation of various mineral additives/wastes, such as coal combustion bottom ash, barley bottom ash, waste glass and metakaolin containing waste as well as calcined illite clays as supplementary cementitious materials, to be used in concrete production as partial cement replacement. Most of the examined materials are used as waste stream materials with potential reactive effect on the concrete. Milling time and fineness of the tested supplementary material has been evaluated and effectiveness was detected. Results indicate that fineness of the tested materials has crucial effect on the concrete compressive strength index. Not in all cases the prolonged milling time can increase fineness and reactivity of the supplementary materials; however the optimal milling time and fineness of the pozolanic additives increased the strength index of concrete up to 1.16 comparing to reference, even in cases when cement was substituted by 20 w%.

SHEAR STRENGTH IN THE GLUE LINE OF Eucalyptus sp. AND Pinus sp.WOOD

Directory of Open Access Journals (Sweden)

Juliana Jerásio Bianche

Full Text Available ABSTRACT To evaluate the adhesive efficiency on the union of glued joints in a particular temperature and humidity conditions for a specified time the adhesive must be submitted to specific load tests, such as shear in the glue line. The objective of this study was to evaluate the shear strength in the glue line of Eucalyptus sp and Pinus sp.woods. Five adhesives (castor oil, sodium silicate, modified silicate, , PVA and resorcinol-formaldehyde, three weights (150 g/m2, 200 g/m2, and 250 g/m2 and two species (Eucalyptus sp. and Pinus sp. of wood were used. Twelve specimens were obtained from each repetition per treatment, corresponding to 108 specimens that were conditioned at a temperature of 23 ± 1°C and relative humidity of 50 ± 2%. The interaction between the weight and type of adhesive was significant for the shear strength in the glue line of eucalyptus wood. However, no interaction between the weight and the adhesive was found for pinus, only the isolated from the adhesive effect. Chemical bonds originated in the polymerization of resorcinol-formaldehyde adhesives and castor bi-component conferred upon these adhesives the greatest resistance in the glue line. Castor and resorcinol-formaldehyde adhesives showed the highest shear strength values in the line of glue and wood failure. Castor adhesive presented satisfactory performance for bonding of eucalyptus and pine woods.

Weighted oscillator strengths and lifetimes for the S VII spectrum

International Nuclear Information System (INIS)

Borges, F.O.; Cavalcanti, G.H.; Trigueiros, A.G.; Jupen, C.

2004-01-01

The weighted oscillator strengths (gf) and the lifetimes presented in this work were carried out in a multiconfiguration Hartree-Fock relativistic approach. In this calculation, the electrostatic parameters were optimized by a least-squares procedure, in order to improve the adjustment to experimental energy levels. This method produces gf-values that are in better agreement with intensity observations and lifetime values that are closer to the experimental ones. In this work, we presented all the experimentally known electric dipole S VII spectral lines

Assessment of clay stiffness and strength parameters using index properties

Directory of Open Access Journals (Sweden)

Sayed M. Ahmed

2018-06-01

Full Text Available A new approach is developed to determine the shear wave velocity in saturated soft to firm clays using measurements of the liquid limit, plastic limit, and natural water content with depth. The shear wave velocity is assessed using the site-specific variation of the natural water content with the effective mean stress. Subsequently, an iterative process is envisaged to obtain the clay stiffness and strength parameters. The at-rest earth pressure coefficient, as well as bearing capacity factor and rigidity index related to the cone penetration test, is also acquired from the analyses. Comparisons are presented between the measured clay parameters and the results of corresponding analyses in five different case studies. It is demonstrated that the presented approach can provide acceptable estimates of saturated clay stiffness and strength parameters. One of the main privileges of the presented methodology is the site-specific procedure developed based on the relationships between clay strength and stiffness parameters, rather than adopting direct correlations. Despite of the utilized iterative processes, the presented approach can be easily implemented using a simple spreadsheet, benefiting both geotechnical researchers and practitioners. Keywords: Soft to firm clays, Atterberg limits, Shear wave velocity, Small-strain shear modulus, Constrained modulus, Undrained shear strength, Effective friction angle, Cone penetration test

Energy levels, oscillator strengths, line strengths, and transition probabilities in Si-like ions of La XLIII, Er LIV, Tm LV, and Yb LVI

Energy Technology Data Exchange (ETDEWEB)

Chen, Zhan-Bin, E-mail: chenzb008@qq.com [College of Science, National University of Defense Technology, Changsha, Hunan 410073 (China); Ma, Kun [School of Information Engineering, Huangshan University, Huangshan 245041 (China); Wang, Hong-Jian [Chongqing Key Laboratory for Design and Control of Manufacturing Equipment, Chongqing Technology and Business University, Chongqing 40067 (China); Wang, Kai, E-mail: wangkai@hbu.edu.cn [Hebei Key Lab of Optic-electronic Information and Materials, The College of Physics Science and Technology, Hebei University, Baoding 071002 (China); Liu, Xiao-Bin [Department of Physics, Tianshui Normal University, Tianshui 741001 (China); Zeng, Jiao-Long [College of Science, National University of Defense Technology, Changsha, Hunan 410073 (China)

2017-01-15

Detailed calculations using the multi-configuration Dirac–Fock (MCDF) method are carried out for the lowest 64 fine-structure levels of the 3s{sup 2}3p{sup 2}, 3s{sup 2}3p3d, 3s3p{sup 3}, 3s3p{sup 2}3d, 3s{sup 2}3d{sup 2}, and 3p{sup 4} configurations in Si-like ions of La XLIII, Er LIV, Tm LV, and Yb LVI. Energies, oscillator strengths, wavelengths, line strengths, and radiative electric dipole transition rates are given for all ions. A parallel calculation using the many-body perturbation theory (MBPT) method is also carried out to assess the present energy levels accuracy. Comparisons are performed between these two sets of energy levels, as well as with other available results, showing that they are in good agreement with each other within 0.5%. These high accuracy results can be used to the modeling and the interpretation of astrophysical objects and fusion plasmas. - Highlights: • Energy levels and E1 transition rates of Si-like ions are presented. • Breit interaction and Quantum Electrodynamics effects are discussed. • Present results should be useful in the astrophysical application and plasma modeling.

Advanced technologies for manufacturing high strength sour grade UOE line pipe

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Kenji; Omura, Tomohiko; Takahashi, Nobuaki; Minato, Izuru; Yamamoto, Akio [Sumitomo Metal Industries, Ltd., Kashima, (Japan)

2010-07-01

A new kind of high strength pipeline has been manufactured for sour service in offshore pipelines. This paper first presents a review of developments in manufacturing technology to improve sour resistance. This was particularly the case with Grade UOE line pipe. The improvement was achieved by optimizing the continuous casting process, monitoring the shape of inclusions (such as MnS, CaS, Al2O3, CaO-Al2O3) and decreasing coarse precipitates (Nb(C,N), TiN). The study then used the HIC evaluation method to determine hydrogen induced cracking (HIC) resistance of the material and HAZ test for sulfide stress cracking (SSC) resistance. The evaluation of the NACE TM0284 solution A showed that these pipelines are able to resist severe sour conditions because of good HIC and SSC resistance. Optimizing others components like alloying elements and the ACC process would improve sour resistance in future applications.

Effective line strengths of trans-nitrous acid near 1275 cm−1 and cis-nitrous acid at 1660 cm−1

International Nuclear Information System (INIS)

Lee, B.H.; Wood, E.C.; Wormhoudt, J.; Shorter, J.H.; Herndon, S.C.; Zahniser, M.S.; Munger, J.W.

2012-01-01

We determined the effective line strengths of the trans conformer of nitrous acid (HONO) near 1275 cm −1 (R-branch of ν 3 mode, N---O---H bend) and of the cis conformer at 1660 cm −1 (R-branch of ν 2 mode, N=O stretch), both at a spectral resolution of 0.001 cm −1 by tunable infrared laser differential absorption spectroscopy (TILDAS) utilizing continuous-wave quantum cascade (cw-QC) lasers. Absorbance of one conformer was measured while simultaneously quantifying the mixing ratio of total HONO by catalytic conversion to nitric oxide (NO) followed by calibrated absorption spectroscopy. Line strengths obtained here are consistent with previously reported band strengths for the trans conformer but are lower by a factor of approximately 2.4 for the cis conformer. -- Highlights: ► Effective line strengths for the cis-HONO at 1660 cm −1 was quantified. ► Effective line strengths for the trans conformer near 1275 cm −1 was also quantified. ► Results for trans-HONO are in agreement with previously published band strength. ► Previous cis band strength is high by factor of 2.4 due to spectral interference.

The McLean-Watson line strength formula and its implementation

International Nuclear Information System (INIS)

Hey, J D

2009-01-01

We consider the application of the line strength formula recently derived by Watson (2006 J. Phys. B: At. Mol. Opt. Phys. 39 L291) to transitions between states of high principal quantum number in hydrogenic atoms and ions (Rydberg-Rydberg transitions). Apparent difficulties in the implementation of this formula are overcome by the use of recurrence relations derived by the ladder operator technique of Infeld and Hull (1951 Rev. Mod. Phys. 23 21), and set out in an earlier paper by the present author (2006 J. Phys. B: At. Mol. Opt. Phys. 39 2641). The use of the McLean-Watson formula for such cases is illustrated by the determination of the radiative lifetimes for levels with n ∼ 1000 and comparison of present results with approximate formulae. Interest in this work on the radial matrix elements for large n and n' is related both to measurements of radio recombination lines from tenuous space plasmas, e.g. Stepkin et al (2007 Mon. Not. R. Astron. Soc. 374 852) and to the calculation of Stark broadening for such spectra, e.g. Gigosos et al (2007 Astron. Astrophys. 466 1189), Stambulchik et al (2007 Phys. Rev. E 75 016401) and Stambulchik and Maron (2008 J. Phys. B: At. Mol. Opt. Phys. 41 095703). In addition, we discuss the question of inaccuracy caused by the omission of fine structure in such calculations, and the numerical stability of the recurrence relations used to implement the line strength formulae.

Gastrocnemius recession leads to medial shift of gait line, impairment of muscle strength and improved dorsal extension in forefoot overload syndrome

DEFF Research Database (Denmark)

Schmal, Hagen; Walther, Markus; Hirschmüller, Anja

2018-01-01

. A strength power analysis of plantar flexors and a pedobarography was performed. Clinical outcome was measured by Foot Function Index (FFI). RESULTS: Plantarflexors are impaired about 40% six weeks and around 10% 24 weeks following GR compared to the contralateral side. Patients experienced a pain relief...... and an improvement of ankle dorsiflexion from 2° to 15°. An increased contact time of the heel (15%) and a shift of metatarsal plantar pressure from lateral to medial could be demonstrated. CONCLUSIONS: This study suggests that GR leads to pain reduction by an increase in heel contact time and a shift of gait line...

Weighted f-values, A-values, and line strengths for the E1 transitions among 3d6, 3d54s, and 3d54p levels of Fe III

International Nuclear Information System (INIS)

Deb, Narayan C.; Hibbert, Alan

2009-01-01

Weighted oscillator strengths, weighted radiative rates, and line strengths for all the E1 transitions between 285 fine-structure levels belonging to the 3d 6 , 3d 5 4s, and 3d 5 4p configurations of Fe III are presented, in ascending order of wavelength. Calculations have been undertaken using the general configuration interaction (CI) code CIV3. The large configuration set is constructed by allowing single and double replacements from any of 3d 6 , 3d 5 4s, 3d 5 4p, and 3d 5 4d configurations to nl orbitals with n≤5,l≤3 as well as 6p. Additional selective promotions from 3s and 3p subshells are also included in the CI expansions to incorporate the important correlation effects in the n=3 shell. Results of some strong transitions between levels of 3d 6 , 3d 5 4s, and 3d 5 4p configurations are also presented and compared with other available calculations. It is found that large disagreements occur in many transitions among the existing calculations

CORRELATION BETWEEN BODY MASS INDEX AND HANDGRIP STRENGTH AND HANDGRIP ENDURANCE AMONG YOUNG HEALTHY ADULTS

Directory of Open Access Journals (Sweden)

Anupi

2015-07-01

Full Text Available BACKGROUND: Physical inactivity has become a serious problem all over the world. Handgrip Strength (a form of isometric static contraction test, is an important test to evaluate the physical fitness and nutritional status of an individua l. A number of factors like a ge, gender, body size, effort, skeletal muscle bulk and contractility may affect the handgrip strength (HGS and handgrip endurance (HGE. AIM: This study was conducted to establish the possible correlation (if any between body mass index and handgrip str ength and endurance among young healthy adults. MATERIALS AND METHODS: A population based cross - sectional study comprising of 200 students (both male and female, age group - 18 - 22 yrs was carried out in the Department of Physiology, Jorhat Medical College. Anthropometric parameters like height and weight were taken to evaluate the BMI and handgrip strength and handgrip endurance were taken by using handgrip dynamometer. According to WHO classification of BMI, subjects were categorized into three groups as un derweight BMI ≤18.5 kg/m 2 , normal weight BMI 18.5 - 24.9 kg/m 2 and overweight BMI≥ 24.9 kg/m 2 . Gender wise difference was analyzed by unpaired t test. Statistical analysis for correlation was done by using Karl Pearson’s Correlation Coefficient denoted by(r. RESULT: Males had higher handgrip strength and handgrip endurance than females. Statistic ally significant correlation was found between BMI and handgrip strength & endurance in underweight & overweight subjects. Gender differences in correlation were observed in correlation between BMI & HGS and HGE. CONCLUSION: The observed influence of BMI a nd gender differences in correlation between BMI and HGS and HGE indicate that besides BMI several other factors like effort, strength, muscular contractility etc . affect muscular strength & endurance in young males and females.

The Gait Deviation Index Is Associated with Hip Muscle Strength and Patient-Reported Outcome in Patients with Severe Hip Osteoarthritis

DEFF Research Database (Denmark)

Rosenlund, Signe; Holsgaard-Larsen, Anders; Overgaard, Søren

2016-01-01

) and with severe primary hip osteoarthritis underwent 3-dimensional gait analysis. Mean Gait Deviation Index, pain after walking and maximal isometric hip muscle strength (flexor, extensor, and abductor) were recorded. All patients completed the 'Physical Function Short-form of the Hip disability...... was to investigate associations between Gait Deviation Index as a measure of gait 'quality' and hip muscle strength and between Gait Deviation Index and patient-reported outcomes in patients with primary hip osteoarthritis. METHOD: Forty-seven patients (34 males), aged 61.1 ± 6.7 years, with BMI 27.3 ± 3.4 (kg/m2...... and Osteoarthritis Outcome Score (HOOS-Physical Function) and the Hip disability and Osteoarthritis Outcome Score subscales for pain (HOOS-Pain) and quality-of-life (HOOS-QOL). RESULTS: Mean Gait Deviation Index was positively associated with hip abduction strength (pstrength (p = 0...

Evaluation of Relationships between Drilling Rate Index and Physical and Strength Properties of Selected Rock Units of Pakistan

International Nuclear Information System (INIS)

Shafique, U.; Abu Bakar, M. Z.

2015-01-01

Fifteen selected rock types collected from different formations of Pakistan were subjected to Drilling Rate Index (DRI) tests and various physical and strength properties tests including, porosity (n), density, primary wave velocity (V/sub p/), uniaxial compressive strength (sigma/sub c/), Brazilian tensile strength (sigma/sub t/) and Schmidt hammer rebound number (R/sub n/),. Prior knowledge of the drill ability of rocks and their physico-mechanical properties plays a decisive role in planning and design of rock drilling and excavation processes. DRI tests developed by NTNU/SINTEF are in use by the industry since 1960s and have proved very successful in estimation of the boreability of rocks, but no such work has been reported for Pakistani rocks to date. Reasonable correlations were found between the DRI and the properties of the tested rocks. The trends shown in this paper are of interest for the machine manufacturers and operators working on various projects involving the use of drilling machines and other mechanical excavators. (author)

In vitro analysis of shear bond strength and adhesive remnant index of different metal brackets

Directory of Open Access Journals (Sweden)

Fernanda de Souza Henkin

Full Text Available ABSTRACT Introduction: There is a great variety of orthodontic brackets in the Brazilian market, and constantly evaluating them is critical for professionals to know their properties, so as to be able to choose which product best suits their clinical practice. Objectives: To evaluate the bond strength and the adhesive remnant index (ARI of different brands of metal brackets. Material and Methods: A total of 105 bovine incisors were used, and brackets of different brands were bonded to teeth. Seven different bracket brands were tested (MorelliTM, American OrthodonticsTM, TP OrthodonticsTM, Abzil-3MTM, OrthometricTM, TecnidentTM and UNIDENTM. Twenty-four hours after bonding, shear bond strength test was performed; and after debonding, the ARI was determined by using an optical microscope at a 10-fold increase. Results: Mean shear bond strength values ranged from 3.845 ± 3.997 (MorelliTM to 9.871 ± 5.106 MPa (TecnidentTM. The majority of the ARI index scores was 0 and 1. Conclusion: Among the evaluated brackets, the one with the lowest mean shear bond strength values was MorelliTM. General evaluation of groups indicated that a greater number of bond failure occurred at the enamel/adhesive interface.

In vitro analysis of shear bond strength and adhesive remnant index of different metal brackets

Science.gov (United States)

Henkin, Fernanda de Souza; de Macêdo, Érika de Oliveira Dias; Santos, Karoline da Silva; Schwarzbach, Marília; Samuel, Susana Maria Werner; Mundstock, Karina Santos

2016-01-01

ABSTRACT Introduction: There is a great variety of orthodontic brackets in the Brazilian market, and constantly evaluating them is critical for professionals to know their properties, so as to be able to choose which product best suits their clinical practice. Objectives: To evaluate the bond strength and the adhesive remnant index (ARI) of different brands of metal brackets. Material and Methods: A total of 105 bovine incisors were used, and brackets of different brands were bonded to teeth. Seven different bracket brands were tested (MorelliTM, American OrthodonticsTM, TP OrthodonticsTM, Abzil-3MTM, OrthometricTM, TecnidentTM and UNIDENTM). Twenty-four hours after bonding, shear bond strength test was performed; and after debonding, the ARI was determined by using an optical microscope at a 10-fold increase. Results: Mean shear bond strength values ranged from 3.845 ± 3.997 (MorelliTM) to 9.871 ± 5.106 MPa (TecnidentTM). The majority of the ARI index scores was 0 and 1. Conclusion: Among the evaluated brackets, the one with the lowest mean shear bond strength values was MorelliTM. General evaluation of groups indicated that a greater number of bond failure occurred at the enamel/adhesive interface. PMID:28125142

Factors influencing the selected body parameters and hippometric indexes in donkey’s population

Directory of Open Access Journals (Sweden)

Martina Kosťuková

2012-01-01

Full Text Available The main focus of our work was to collect basic body measurements of donkey population in Czech republic and determine the factors that influence these body measurements and hipometric indexes. The following measurements were recorded: height at withers, chest circumference and metacarpus interference. Based on the collected data, we were able to calculate the hipometric indexes: index of boniness, skeleton strength index, body mass index and coup height index. From a total of 331 individuals of donkey species living in Czech republic we managed to collect 50 samples. These were subjected to a general linear model (GLM and multiplex comparison statistical analysis. We managed to prove a statistically significant difference between donkeys born in Czech republic and the ones born abroad for all the measurements. Specifically the metacarpus circumference the gender dependency was also proved, having its impact on the hipometric indexes as well; the boniness index and skeleton strength index were also proved to be gender – dependent.

Absorption-line strengths of 18 late-type spiral galaxies observed with SAURON

NARCIS (Netherlands)

Ganda, Katia; Peletier, Reynier F.; McDermid, Richard M.; Falcon-Barroso, Jesus; de Zeeuw, P. T.; Bacon, Roland; Cappellari, Michele; Davies, Roger L.; Emsellem, Eric; Krajnovic, Davor; Kuntschner, Harald; Sarzi, Marc; van de Ven, Glenn

2007-01-01

We present absorption line strength maps for a sample of 18 Sb-Sd galaxies observed using the integral-field spectrograph SAURON operating at the William Herschel Telescope on La Palma, as part of a project devoted to the investigation of the kinematics and stellar populations of late-type spirals,

Oscillator strengths for neutral technetium

International Nuclear Information System (INIS)

Garstang, R.H.

1981-01-01

Oscillator strengths have been calculated for most of the spectral lines of TcI which are of interest in the study of stars of spectral type S. Oscillator strengths have been computed for the corresponding transitions in MnI as a partial check of the technetium calculations

Contingency management of power system with Interline Power Flow Controller using Real Power Performance Index and Line Stability Index

Directory of Open Access Journals (Sweden)

Akanksha Mishra

2016-03-01

Full Text Available As a result of privatization of the electrical industry the power transmission lines have to transfer power at their maximum transmission limits because of the competitive scenario of the electrical market. Hence, secured operation of power system has become one of the most important issues of modern era. In this paper, a probability of severity based placement strategy for Interline Power Flow Controller (IPFC has been proposed based on Composite Severity Index (CSI. The composite severity index provides an exact measure of stress in the line in terms of mega watt overloading and voltage instability. IPFC is placed on the line which has the highest probability of severity during the occurrence of different outages. The IPFC has been tuned for a multi-objective function using Differential Evolution (DE and the results have been compared with genetic Algorithm (GA. To verify the proposed method, it has been tested and implemented on IEEE 14 and 57 bus systems.

CALCULATION METHOD OF ELECTRIC POWER LINES MAGNETIC FIELD STRENGTH BASED ON CYLINDRICAL SPATIAL HARMONICS

Directory of Open Access Journals (Sweden)

A.V. Erisov

2016-05-01

Full Text Available Purpose. Simplification of accounting ratio to determine the magnetic field strength of electric power lines, and assessment of their environmental safety. Methodology. Description of the transmission lines of the magnetic field by using techniques of spatial harmonic analysis in the cylindrical coordinate system is carried out. Results. For engineering calculations of electric power lines magnetic field with sufficient accuracy describes their first spatial harmonic magnetic field. Originality. Substantial simplification of the definition of the impact of the construction of transmission line poles on the value of its magnetic field and the bands of land alienation sizes. Practical value. The environmentally friendly projection electric power lines on the level of the magnetic field.

The SAURON project - VI. Line strength maps of 48 elliptical and lenticular galaxies

NARCIS (Netherlands)

Kuntschner, Harald; Emsellem, Eric; Bacon, R.; Bureau, M.; Cappellari, Michele; Davies, Roger L.; de Zeeuw, P. T.; Falcon-Barroso, Jesus; Krajnovic, Davor; McDermid, Richard M.; Peletier, Reynier F.; Sarzi, Marc

2006-01-01

We present absorption line strength maps of 48 representative elliptical and lenticular galaxies obtained as part of a survey of nearby galaxies using our custom-built integral-field spectrograph, SAURON, operating on the William Herschel Telescope. Using high-quality spectra, spatially binned to a

The strengths perspective in client’s social case management

OpenAIRE

Valpētere, Laima

2010-01-01

The subject diploma paper is „The strengths perspective in client’s social case management.” The aim of the diploma paper is to research the strengths perspective in client’s social case management. Diploma paper consists of five chapters. In the first chapter the case management was theoretically researched. In the second chapter was done description of the strengths perspective in the social work. In the third chapter by describing principles and strategies of strengths perspective, cli...

Interrelationships of serum testosterone and free testosterone index with FFM and strength in aging men.

Science.gov (United States)

Roy, Tracey Ann; Blackman, Marc R; Harman, S Mitchell; Tobin, Jordan D; Schrager, Matthew; Metter, E Jeffery

2002-08-01

Muscle mass and strength losses during aging may be associated with declining levels of serum testosterone (T) in men. Few studies have shown a direct relationship between T and muscle mass and strength. Subjects were 262 men, aged 24-90 yr, from the Baltimore Longitudinal Study of Aging, who had T and sex hormone-binding globulin sex hormone-binding globulin (SHBG) measurements, from which the free T index (FTI) was calculated (T/SHBG) from serum samples collected longitudinally since 1963, total body fat mass and arm and leg fat-free mass (FFM) by dual-energy X-ray absorptiometry and arm and leg strength by dynanomometry. Mixed-effects models estimated T and FTI at the time of mass and strength measurements. Age, total body fat, arm and leg FFM, T, and FTI were significantly associated with concentric and eccentric strength. FTI, not T, was modestly, but directly, related to arm and leg strength after fat, arm and leg FFM, height, and age were accounted for and indirectly through body mass. FTI is a better predictor of arm and leg strength than T in aging men.

Atomic spectroscopy sympsoium, Gaithersburg, Maryland, September 23--26, 1975. [Program, abstracts, and author index

Energy Technology Data Exchange (ETDEWEB)

1975-01-01

Abstracts of one hundred papers given at the conference are presented along with the conference program and an author index. Session topics include: highly ionized atoms; laser spectroscopy and hyperfine structure; complex spectra; laser spectroscopy, radiation theory; theory of highly ionized atoms and analysis of plasmas; plasma spectroscopy, line strengths; spectral analysis, instrumentation, reference wavelengths; beam foil spectroscopy, line strengths, energy levels; absorption spectroscopy, autoionization, and related theory; and spectral analysis, instrumentation, and VUV physics. (GHT)

Construction of Lines of Constant Density and Constant Refractive Index for Ternary Liquid Mixtures.

Science.gov (United States)

Tasic, Aleksandar Z.; Djordjevic, Bojan D.

1983-01-01

Demonstrates construction of density constant and refractive index constant lines in triangular coordinate system on basis of systematic experimental determinations of density and refractive index for both homogeneous (single-phase) ternary liquid mixtures (of known composition) and the corresponding binary compositions. Background information,…

A study of the oscillator strengths and line strenghts of Agl and AuI Using the Coulomb approximation

Directory of Open Access Journals (Sweden)

M. Soltanolkotabi

1998-04-01

Full Text Available   Single-valence electron atoms are an important class of atoms. Their oscillator strengths are their important properties. Knowing the oscillator strengths one can easity calculate the transition probabilities of the spectral lines and hence the lifetimes of energy levels of most atoms. The oscillator strengths of the spectral lines of most atoms are not knoen with sufficient accuracy due to the experimental difficulties. The results of most measurements are subject to large inaccuracies due to uncertainties in vapor pressure data. A quick and simple theoretical method for calculation of atomic oscillator strength seems to be the Coulomb approximation of Bates and Damagaard. This method reveals some interesting properties that are generally confirmed by experimental results. In this paper, we have studied oscillator strengths and line strengths of the different allowed transitions in AgI and AuI using the Coulomb approximation. The log (λfg curves(λ, f and g are the wavelength of transition, oscillator strength and statistical weight of upper level, respectively versus the reciprocal of the principal quantum number of upper level, 1/n, show a linear behavior only for large values of the principal quantum number of lower level. The effect of change of total angular momentum,Δ J, in the curvature and slope of the plotted curves has been also investigated. The deviation of the curves from straight lines, which indicates failure of the Coulomb approximation is due to the exchange forces. In addition, the n3fg curves   (n , the effective total quantum number of upper level have been plotted versus n for different allowed transitions in AgL and AuI. It has been found that f is proportional to 1/n and this proportionality is linear for large values of n . For some transitions, however, there is a significant deviation from the linear dependence for large values of n , which can be attributed to the signature of total angular momentum quantum

The SAURON project : XVIII. The integrated UV-line-strength relations of early-type galaxies

NARCIS (Netherlands)

Bureau, Martin; Jeong, Hyunjin; Yi, Sukyoung K.; Schawinski, Kevin; Houghton, Ryan C. W.; Davies, Roger L.; Bacon, Roland; Cappellari, Michele; de Zeeuw, P. Tim; Emsellem, Eric; Falcon-Barroso, Jesus; Krajnovic, Davor; Kuntschner, Harald; McDermid, Richard M.; Peletier, Reynier F.; Sarzi, Marc; Sohn, Young-Jong; Thomas, Daniel; van den Bosch, Remco C. E.; van de Ven, Glenn

Using far-ultraviolet (FUV) and near-ultraviolet (NUV) photometry from guest investigator programmes on the Galaxy Evolution Explorer (GALEX) satellite, optical photometry from the MDM Observatory and optical integral-field spectroscopy from SAURON, we explore the UV-line-strength relations of the

Spectra of Wolf-Rayet stars. I. Optical line strengths and the hydrogen-to-helium ratios in WN type stars

International Nuclear Information System (INIS)

Conti, P.S.; Leep, E.M.; Perry, D.N.

1983-01-01

We begin a series of systematic studies of spectra of Wolf-Rayet stars by examining the optical line strengths of WN stars in the Galaxy and the Large Magellanic Cloud to see what similarities and differences exist among them. Tables of equivalent widths extracted from spectra are presented and some conclusions are drawn. We have found that there is a wide dispersion, up to a factor of 10 or more, in line strengths for all ions even among stars of the same subtype, with WN 7 stars weaker overall than surrounding types. Type-to-type trends are consistent with changing ionization balance in the stellar wind. Nitrogen line ratios indicate that the WN subtypes represent an ionization sequence, but one with considerable overlap: the classification scheme is not single valued; other physical parameters must play a role. The line strength dispersion does not appear to be primarily due to ionization, or luminosity. The Balmer-Pickering decrement has been used to estimate the H/He ratio for most of the WN stars with available spectra; semiquantitative results are presented. Significant differences in H/He are observed (10 stars may have H/He>2). At a given subclass, the strongest line stars have no detectable H. The abundance of H probably relates to structural differences in the winds that, in part, give rise to a dispersion in observed line strengths. Finally, we have estimated the C/N ratio from the C IV lambda5805/N IV lambda4057 line ratio. In most cases our observations suggest that the C/N ratio is consistent with ''evolved'' models for WN stars. A few stars show strong C IV implying much larger values for C/N, but hydrogen was not detected in them. These stars may be in transition from the WN to WC classes

COLLISION STRENGTHS AND EFFECTIVE COLLISION STRENGTHS FOR TRANSITIONS WITHIN THE GROUND-STATE CONFIGURATION OF S III

Energy Technology Data Exchange (ETDEWEB)

Hudson, C. E.; Ramsbottom, C. A.; Scott, M. P., E-mail: c.hudson@qub.ac.uk, E-mail: c.ramsbottom@qub.ac.uk, E-mail: p.scott@qub.ac.uk [Department of Applied Maths and Theoretical Physics, The Queen' s University of Belfast, Belfast BT7 1NN (United Kingdom)

2012-05-01

We have carried out a 29-state R-matrix calculation in order to calculate collision strengths and effective collision strengths for the electron impact excitation of S III. The recently developed parallel RMATRX II suite of codes have been used, which perform the calculation in intermediate coupling. Collision strengths have been generated over an electron energy range of 0-12 Ryd, and effective collision strength data have been calculated from these at electron temperatures in the range 1000-100,000 K. Results are here presented for the fine-structure transitions between the ground-state configurations of 3s {sup 2}3p {sup 23} P{sub 0,1,2}, {sup 1}D{sub 2}, and {sup 1} S{sub 0}, and the values given resolve a discrepancy between two previous R-matrix calculations.

Coulomb field strength measurement by electro-optic spectral decoding system at the CALIFES beam line

CERN Document Server

Pan, R; Lefevre, T; Gillepsie, WA; CERN. Geneva. ATS Department

2016-01-01

Electro-optic (EO) techniques are increasingly used for longitudinal bunch profile measurements. A bunch profile monitor, based on electro-optic spectral decoding(EOSD), has been developed and demonstrated on the CALIFES beam line at CERN. The EO response is analysed using a frequency domain description, and two methods for extraction of absolute Coulomb field strengths from the electron bunch are demonstrated. Measurements at field strengths up to 1.3 MV/m agree with the expectation based on independent charge measurements.

Linear scleroderma following Blaschko′s lines

Directory of Open Access Journals (Sweden)

Mukhopadhyay Amiya

2005-01-01

Full Text Available Blaschko′s lines form a pattern, which many diseases are found to follow, but linear scleroderma following Blaschko′s lines is a controversial entity rarely reported in the literature. A 24-year-old man presented with multiple linear, atrophic, hyperpigmented lesions punctuated by areas of depigmentations on the left half of the trunk distributed on the anterior, lateral and posterior aspects. The lesions were distributed in a typical S-shaped line. Antinuclear antibody and antihistone antibody tests were negative. Histopathological examination of the skin from the affected area showed features suggestive of scleroderma. Here, we present a case of linear scleroderma following Blaschko′s lines in a male patient - an entity reported only three times so far.

A surface acoustic wave electric field strength meter for environmental studies of HV transmission lines

International Nuclear Information System (INIS)

Grandolfo, M.; Ranghiasci, C.; Verona, E.

1988-01-01

In recent years, there has been a significant increase in concern over the health and safety aspects of high voltage transmission lines (HVTL). The majority of research has focused on effects directly or indirectly involved with the central nervous system, including physiological, ultrastructural, and biochemical alterations, changes in blood composition, behaviour, reproduction, and development. Several recent epidemiological reports have presented preliminary data suggesting an increase in the incidence of cancer among children and adults exposed to magnetic fields through living close to various types of electrical power lines or devices. With the increase in environmental concerns there has been a concomitant consideration of biological effects and health implications related to presently existing HVTL and those planned in the future. It was concluded that the electric and magnetic field strengths and the electrical discharges are the most important electrophysical factors. Thus, it has been deemed necessary to develop measuring means to determine the field strengths in areas surrounding electric installations, in particular at ground level. In the present paper an electric field meter, based on the use of a surface acoustic wave (SAW) delay line, is presented and the experimental results obtained are discussed

Line strength variations in gamma-ray burst GB870303: Possible evidence of neutron star rotation

International Nuclear Information System (INIS)

Graziani, C.; Fenimore, E.E.; Murakami, T.; Yoshida, A.; Lamb, D.Q.; Wang, J.C.L.; Loredo, T.J.

1991-01-01

An exhaustive search of the Ginga data on γ-ray burst GB870303 reveals two separate time intervals during which statistically significant line features are evident. One (previously unreported) interval shows a single prominent line feature at ∼20 keV; a second, corresponding to the interval reported by Murakami et al., shows two line features at ∼20 and 40 keV. From model fits to the data, we find that both sets of lines are well-described by cyclotron resonant scattering in a magnetic field B∼1.8x10 12 G, and that the differences in the line strengths between the two intervals are significant. The variations are qualitatively similar to those produced by a change in the viewing angle θ relative the magnetic field. We conjecture that the change in θ is due to rotation of the neutron star, and derive limits 45 sec approx-lt P approx-lt 180 sec on the rotation period P

Effect of surface treatments on the bond strength of soft denture lining materials to an acrylic resin denture base.

Science.gov (United States)

Gundogdu, Mustafa; Yesil Duymus, Zeynep; Alkurt, Murat

2014-10-01

Adhesive failure between acrylic resin and resilient liner material is commonly encountered in clinical practice. The purpose of this study was to evaluate the effect of different surface treatments on the bond strength of 2 different resilient lining materials to an acrylic resin denture base. Ninety-six dumbbell-shaped specimens were fabricated from heat-polymerized acrylic resin, and 3 mm of the material was cut from the thin midsection. The specimens were divided into 6 groups according to their surface treatments: no surface treatment (control group), 36% phosphoric acid etching (acid group), erbium:yttrium-aluminum-garnet (Er:YAG) laser (laser group), airborne-particle abrasion with 50-μm Al2O3 particles (abrasion group), an acid+laser group, and an abrasion+laser group. The specimens in each group were divided into 2 subgroups according to the resilient lining material used: heat-polymerized silicone based resilient liner (Molloplast B) and autopolymerized silicone-based resilient liner (Ufi Gel P). After all of the specimens had been polymerized, they were stored in distilled water at 37°C for 1 week. A tensile bond strength test was then performed. Data were analyzed with a 2-way ANOVA, and the Sidak multiple comparison test was used to identify significant differences (α=.05). The effects of the surface treatments and resilient lining materials on the surface of the denture base resin were examined with scanning electron microscopy. The tensile bond strength was significantly different between Molloplast B and Ufi Gel P (P<.001). The specimens of the acid group had the highest tensile bond strength, whereas those of the abrasion group had the lowest tensile bond strength. The scanning electron microscopy observations showed that the application of surface treatments modified the surface of the denture base resin. Molloplast B exhibited significantly higher bond strength than Ufi Gel P. Altering the surface of the acrylic resin denture base with 36

SU-E-T-270: Quality Control of Source Strength and Indexer Length in HDR Brachytherapy Using Sun Nuclear Mapcheck2

International Nuclear Information System (INIS)

Morales, J

2014-01-01

Purpose: The goal of this work was to evaluate Sun Nuclear MapCheck2 capability for quantitative determination of both HDR source strength and position. Predictive power of Mapcheck2 dose matrix, originated by a microSelectron-v2 source from 22mm distance, was investigated. Methods: A Mick MultiDoc phantom with the 1400mm indexer length mark aligned over MapCheck2 central detector plus two additional 5cm plastic slabs were used as a composite phantom. Dose readings were transformed by applying published source anisotropy corrections and experimentally established radial dose and relative sensitivity factors. Angular dependence was not considered. Only readings from diodes located 2cm around the central detector were evaluated. The reproducibility of a fit between transformed dose readings and the ratio of virtual source strength and the square of source-detector distance was investigated. Four parameters were considered in the model: virtual source strength, lateral, longitudinal and vertical source positions. Final source strength calibration factor was calculated from the ratio of reference measurements and results from the fit. Results: Original lateral and longitudinal source position estimations had systematic errors of 0.39mm and 0.75mm. After subtracting these errors, both source positions were predicted with a standard deviation of 0.15mm. Results for vertical positions were reproducible with a standard deviation of 0.05mm. The difference between calculated and reference source strengths from 34 independent measurement setups had a standard deviation of 0.3%. The coefficient of determination for the linear regression between known indexer lengths and results from the fit in the range 1400mm ± 5mm was 0.985. Conclusions: ource strength can be estimated with MapCheck2 at appropriate accuracy levels for quality control. Verification of indexer length with present implementation is more accurate than visual alternatives. Results can be improved by designing a

Exploring the Hjif-Index, an Analogue to the H-Like Index for Journal Impact Factors

Directory of Open Access Journals (Sweden)

William Cabos

2018-04-01

Full Text Available We used the Journal Impact Factor (JIF to develop the hjif-index, calculated in a similar way to h-like indices. To this end, we mapped the JIFs of one JCR group to natural numbers, and evaluated the degree of correspondence between the interval from zero to the highest JIF in the group and a set of natural numbers. Next, we plotted the straight line y = x to obtain the group’s hjif-index as the JIF corresponding to the journal immediately above the straight line. We call the set of journals above the straight line the hjif-core. We calculated hjif-indices corresponding to the 2-year JIF (hjif2-index and 5-year JIF (hjif5-index windows for all 176 JCR groups listed in the 2014 Science edition. We also studied derived indicators such as the distribution of journals in JCR groups according to their hjif-indices, the distribution of journals and JIFs in the hjif-core, and other variables and indicators. We found that the hjif2- and hjif5-index behaved in a similar way, and that in general their distribution showed a peak followed by a relatively long tail. The hjif-index can be used as a tool to rank journals in a manner that better reflects the variable number of journals within a given JCR group and in each group’s hjif-core as an alternative to the more arbitrary JCR-based percentile ranking.

ECONOMETRIC’S MODEL: THE DEPENDENCE OF PFTS INDEX FROM ECONOMICS RANKS

OpenAIRE

K. Cherkashyna

2013-01-01

Dynamics of stock index is an indicator of market efficiency. We use the strong form of market efficiency, where prices reflect all available information, – both public and private. National index PFTS and main world indexes such as Dow Jones industrial, Standard & Poor’s 500, Nasdaq composite, Japan’s Nikkei index, Hong Kong’s Hang Seng index are very volatility. Last week all of the major U.S. stock indexes were in the red. Data dependence index PFTS from many exogenous and internal factors...

The SAURON project - XI. Stellar populations from absorption-line strength maps of 24 early-type spirals

NARCIS (Netherlands)

Peletier, Reynier F.; Falcon-Barroso, Jesus; Bacon, Roland; Cappellari, Michele; Davies, Roger L.; de Zeeuw, P. T.; Emsellem, Eric; Ganda, Katia; Krajnovic, Davor; Kuntschner, Harald; McDermid, Richard M.; Sarzi, Marc; van de Ven, Glenn

2007-01-01

We present absorption-line strength maps of a sample of 24 representative early-type spiral galaxies, mostly of type Sa, obtained as part of the SAURON (Spectrographic Areal Unit for Research on Optical Nebulae) survey of nearby galaxies using our custom-built integral-field spectrograph. Using

Hollow-cathode lamps as optical frequency standards: the influence of optical imaging on the line-strength ratios

Science.gov (United States)

Huke, Philipp; Tal-Or, Lev; Sarmiento, Luis Fernando; Reiners, Ansgar

2016-07-01

Hollow cathode discharge lamps (HCLs) have been successfully used in recent years as calibration sources of optical astronomical spectrographs. The numerous narrow metal lines have stable wavelengths, which makes them well suited for m/s calibration accuracy of high-resolution spectrographs, while the buffer-gas lines are less stable and less useful. Accordingly, an important property is the metal-to-gas line-strength ratio (Rmetal/gas). Processes inside the lamp cause the light to be emitted from different regions between the cathode and the anode leaing to the emission of different beams with different values of Rmetal/gas. We used commercially- available HCLs to measure and characterize these beams with respect to their spatial distribution, their angle of propagation relative to the optical axis, and their values of Rmetal/gas. We conclude that a good imaging of an HCL into a fiber-fed spectrograph would consist of an aperture close to its front window in order to filter out the parts of the beam with low Rmetal/gas, and of a lens to collimate the important central beam. We show that Rmetal/gas can be further improved with only minor adjustments of the imaging parameters, and that the imaging scheme that yields the highest Rmetal/gas does not necessarily provide the highest flux.

Correlations among visual analogue scale, neck disability index, shoulder joint range of motion, and muscle strength in young women with forward head posture.

Science.gov (United States)

Shin, Young Jun; Kim, Won Hyo; Kim, Seong Gil

2017-08-01

This study investigated the correlation between the neck disability index (NDI) and visual analogue scale (VAS), which are indicators of neck pain, shoulder joint range of motion (ROM), and muscle strength in women with a slight forward head posture. This study was carried out on 42 female college students attending Uiduk University in Gyeongju, Korea. The neck pain and disability index for each subject was measured using VAS and NDI, respectively. Two physiotherapists measured the shoulder joint ROM and muscle strengths of the subjects using a goniometer and a dynamometer, respectively. External rotation, internal rotation, and abduction of the shoulder joint were measured for each subject. A significant negative correlation between neck pain and shoulder joint ROM in external rotation and the muscle strength of the shoulder joint in abduction was found in the subjects. In addition, a significant positive correlation was observed between ROM in external rotation and muscle strength in abduction. This study showed a significant negative correlation between neck pain and ROM in external rotation as well as between neck pain and the muscle strength in abduction.

Using the reactive strength index modified to evaluate plyometric performance.

Science.gov (United States)

Ebben, William P; Petushek, Erich J

2010-08-01

The ability to develop force quickly is a requisite ability in most sports. The reactive strength index (RSI) has been developed as a measure of explosive strength and is derived by evaluating jump height divided by ground contact time during the depth jump (DJ). At present, the RSI is typically used to evaluate DJ performance, because it is the only plyometric exercise with an identifiable ground contact time. The purpose of this study was to introduce a modification of the RSI (RSImod) that can be used to evaluate the explosive power of any vertical plyometric exercise. This study will also assess the reliability of the RSImod, evaluate the RSImod of a variety of plyometric exercises, and examine gender differences. Twenty-six men and 23 women served as subjects. Subjects performed 3 repetitions for each of 5 plyometric exercises including the countermovement jump (CMJ), tuck jump, single-leg jump, squat jump, and dumbbell CMJ. Data were analyzed using a 2-way analysis of variance to evaluate differences in RSImod between the plyometric exercise and the interaction between plyometric exercise RSImod and gender. The analysis of RSImod revealed significant main effects for plyometric exercise type (p plyometric exercise type and gender (p > 0.05). Results of pairwise comparisons indicate that the RSImod is statistically different between all plyometric exercises studied. Intraclass correlation coefficients indicate that RSImod is highly reliable for all of the exercises studied. The RSImod offers a highly reliable method of assessing the explosiveness developed during a variety of plyometric exercises.

On the discovery of K I 7699 Å line strength variation during the 1982-1984 eclipse of ε Aurigae

Science.gov (United States)

Parthasarathy, M.

2017-02-01

The discovery of K I 7699 Å line strength variations during the 1982-1984 eclipse of ε Aurigae is described. The equivalent widths and radial velocities of the K I 7699 Å line derived from spectra obtained during 1981 November-1983 July with the 2.1 m Otto Struve reflector telescope of the McDonald observatory are presented.

Theoretical Atomic Physics code development IV: LINES, A code for computing atomic line spectra

International Nuclear Information System (INIS)

Abdallah, J. Jr.; Clark, R.E.H.

1988-12-01

A new computer program, LINES, has been developed for simulating atomic line emission and absorption spectra using the accurate fine structure energy levels and transition strengths calculated by the (CATS) Cowan Atomic Structure code. Population distributions for the ion stages are obtained in LINES by using the Local Thermodynamic Equilibrium (LTE) model. LINES is also useful for displaying the pertinent atomic data generated by CATS. This report describes the use of LINES. Both CATS and LINES are part of the Theoretical Atomic PhysicS (TAPS) code development effort at Los Alamos. 11 refs., 9 figs., 1 tab

A two-dimensional uniplanar transmission-line metamaterial with a negative index of refraction

International Nuclear Information System (INIS)

Elek, Francis; Eleftheriades, George V

2005-01-01

A uniplanar transmission-line (TL) network has been loaded with lumped elements (chip or printed), enabling one to achieve a two-dimensional (2D) uniplanar negative-refractive-index (NRI) metamaterial. The metamaterial consists of a 2D array of unit cells, composed of TL sections connected in series and loaded in a specified manner. The unit cell dimensions can be designed to be much smaller than the operating wavelength, enabling one to identify the structure as an effective medium, with a negative index of refraction. This NRI metamaterial supports transverse electric (TE) waves, as opposed to related previous work on NRI-TL media that supported transverse magnetic (TM) waves. The dispersion characteristics are calculated using a simple, fast 2D loaded TL model with periodic (Bloch) boundary conditions. Subsequently the dispersion relation is simplified in the homogeneous limit, thus allowing one to identify effective permittivities and permeabilities, which are shown to be simultaneously negative. Simulations demonstrating the negative refraction of a plane wave on an interface between such a NRI uniplanar metamaterial and a commensurate positive-refractive-index (PRI) metamaterial verify the validity of the proposed concept and theory. A fully printed unit cell is presented at microwave frequencies (∼10 GHz) along with a prescription for synthesizing an isotropic 3D transmission line NRI metamaterial based on this unit cell

Effect of pilates method on inspiratory and expiratory muscle strength in the elderly

Directory of Open Access Journals (Sweden)

Beatriz Mendes Tozim

2018-03-01

Full Text Available With aging, the respiratory muscle strength decreases and the pilates method is a technique that uses respiration as one of its principles. The present study has the aim of analyzing the influence of the pilates method on respiratory muscle strength in older women. For the evaluation of respiratory muscle strength (inspiratory and expiratory, manovacuometer was used. Thirty-one older women were divided into two groups: 14 participated in the pilates group and 17 in the control group. Participants of the pilates group performed 16 sessions of pilates method with an hour of training, twice week for eight weeks. The control group participated in four educational lectures for eight weeks. For statistical analysis, Shapiro-Wilk, ANOVA for repeated measures (p <0.05 and Cohen’s D index were performed. The results showed significant difference and the mean effect for the Cohen’s D index expiratory muscle strength of the pilates group when comparing before (69.71 ± 25.48 and after (85.23 ± 22.21 training (p<0.05 with an increase of 23%. The results of inspiratory muscle strength were not significant but presented an average effect for the Cohen’s D index for the pilates group before (69.71 ± 35.46 and after (88.00 ± 34.87 training, with an increase of 27%. The control group did not present significant differences for the variables evaluated. It could be concluded that the pilates method is effective in improving expiratory muscle strength and provides positive effects on the increase in inspiratory muscle strength.

Fracture line index of fibular stalk and the ankle joint bone in the classification of the ankle joint trauma

International Nuclear Information System (INIS)

Wu Jun; Zhang Qiang

2003-01-01

Objective: To evaluate the fracture line index of fibular stalk and the ankle joint bone in the classification of the ankle joint trauma. Methods: Measure fracture line index of fibular stalk and the ankle joint in 217 adult cases of fracture and dislocation of ankle joint. And the cases were classified by the results of the measurement. Results: Measurement was unavailable in 9 cases of tearing fracture. In 31 cases, the lesions could not be particularly classified. And in the rest 176 cases the trauma were precisely classified. The over all successful rate was 81.6%. Conclusion: Fracture line index of fibular stalk and the ankle joint bone are valuable in classification of the trauma of the angle joint. While the specificity of this method is low in differentiating the adducting and abducting fracture of the medial angle, in which a combined investigation is recommended

Effect of Body Mass Index on Postural Balance and Muscle Strength in Children Aged 8-10 years

Directory of Open Access Journals (Sweden)

Lucky Prasetiowati

2017-04-01

Full Text Available Background:Childhood overweight and obesity, which are considered as global epidemic, can be assessed using Body Mass Index (BMI. BMI difference can lead to anatomic changes due to an increased body load. This increase might also affect motor performance, including changes in postural balance and muscle strength. Aims and Objectives: to explain the influence of BMI on postural balance and lower limb muscle strength and to assess the correlation between those two variables in children aged 8-10 years. Material and methods:The sample consisted of 63 children aged 8-10 years, which were divided in 3 groups: BMI-normal, BMI-overweight, and BMI-obese. The postural balance was assessed using single leg balance test on MatScan and the Center Of Pressure (COP area was recorded. Isometric muscle strength of hip extensor and knee extensor were measured using a hand-held dynamometer. Results: Obese children had significantly largerCOP area than overweight (p = 0.004 and normal weight children (p = 0.000.There were no significant differences in hip extensor muscle strength between obese children with overweight and normal weight children (p=0.527. The absolute knee extensor muscle strength in obese group was significantly higher than the overweight and normal group (p = 0.003. However the relative muscle strength of lower limb for obese children was significantly lower than for normal weight. There was no significant correlation between absolute hip extensor and knee extensor muscles strength with COP area. Conclusion: Obese children have decreased postural balance and increased absolute knee extensormuscle strength significantly when compared to overweight and normal children. There is no significant correlation between postural balance and muscle strength.

Characteristics of structural loess strength and preliminary framework for joint strength formula

OpenAIRE

Rong-jian Li; Jun-ding Liu; Rui Yan; Wen Zheng; Sheng-jun Shao

2014-01-01

The strength of structural loess consists of the shear strength and tensile strength. In this study, the stress path, the failure envelope of principal stress (Kf line), and the strength failure envelope of structurally intact loess and remolded loess were analyzed through three kinds of tests: the tensile strength test, the uniaxial compressive strength test, and the conventional triaxial shear strength test. Then, in order to describe the tensile strength and shear strength of structural lo...

Polarized Line Formation in Arbitrary Strength Magnetic Fields Angle-averaged and Angle-dependent Partial Frequency Redistribution

Energy Technology Data Exchange (ETDEWEB)

Sampoorna, M.; Nagendra, K. N. [Indian Institute of Astrophysics, Koramangala, Bengaluru 560 034 (India); Stenflo, J. O., E-mail: sampoorna@iiap.res.in, E-mail: knn@iiap.res.in, E-mail: stenflo@astro.phys.ethz.ch [Institute of Astronomy, ETH Zurich, CH-8093 Zurich (Switzerland)

2017-08-01

Magnetic fields in the solar atmosphere leave their fingerprints in the polarized spectrum of the Sun via the Hanle and Zeeman effects. While the Hanle and Zeeman effects dominate, respectively, in the weak and strong field regimes, both these effects jointly operate in the intermediate field strength regime. Therefore, it is necessary to solve the polarized line transfer equation, including the combined influence of Hanle and Zeeman effects. Furthermore, it is required to take into account the effects of partial frequency redistribution (PRD) in scattering when dealing with strong chromospheric lines with broad damping wings. In this paper, we present a numerical method to solve the problem of polarized PRD line formation in magnetic fields of arbitrary strength and orientation. This numerical method is based on the concept of operator perturbation. For our studies, we consider a two-level atom model without hyperfine structure and lower-level polarization. We compare the PRD idealization of angle-averaged Hanle–Zeeman redistribution matrices with the full treatment of angle-dependent PRD, to indicate when the idealized treatment is inadequate and what kind of polarization effects are specific to angle-dependent PRD. Because the angle-dependent treatment is presently computationally prohibitive when applied to realistic model atmospheres, we present the computed emergent Stokes profiles for a range of magnetic fields, with the assumption of an isothermal one-dimensional medium.

Strength-ductility relationships in intermediate purity hot-pressed beryllium

International Nuclear Information System (INIS)

Stonehouse, A.J.; Bielawski, C.A.; Paine, R.M.

1977-01-01

The strength of vacuum hot-pressed, intermediate purity beryllium may be substantially increased without sacrifice of the strain capacity of the present grade (S-65) through decrease in the average grain size. Tensile strength of 517 MPa, 0.2% offset yield strength of 414 MPa with minimum 3% tensile elongation in all test directions could be commercially achieved. The tangent modulus of such material is quite attractive and suffers only about 10% degradation from room temperature to 260 0 C. The tangent modulus is dramatically enhanced by the presence of a yield point. The ductility of the materials studied did not appear to be affected by the BeO content across the range of 0.5 to 2.0% using nominal -44 to -15 μm powder particle sizes. All fine-grained pressings exhibited yield points in the as-pressed condition. Either full-density or sub-density hot-pressed billets given a hot isostatic pressing treatment without the use of cans showed only slight yield points after the HIP treatment with essentially the same strength and ductility factors as in the pressed condition. A plot of grain size vs yield strength in the as-pressed condition projects to an intercept with the fracture strength line at about 3 μm grain size. A similar plot after the HIP treatment shows a yield strength line parallel to the fracture strength line with no projected intercept predicting a completely brittle material. (author)

Relationships Between Countermovement Jump Ground Reaction Forces and Jump Height, Reactive Strength Index, and Jump Time.

Science.gov (United States)

Barker, Leland A; Harry, John R; Mercer, John A

2018-01-01

Barker, LA, Harry, JR, and Mercer, JA. Relationships between countermovement jump ground reaction forces and jump height, reactive strength index, and jump time. J Strength Cond Res 32(1): 248-254, 2018-The purpose of this study was to determine the relationship between ground reaction force (GRF) variables to jump height, jump time, and the reactive strength index (RSI). Twenty-six, Division-I, male, soccer players performed 3 maximum effort countermovement jumps (CMJs) on a dual-force platform system that measured 3-dimensional kinetic data. The trial producing peak jump height was used for analysis. Vertical GRF (Fz) variables were divided into unloading, eccentric, amortization, and concentric phases and correlated with jump height, RSI (RSI = jump height/jump time), and jump time (from start to takeoff). Significant correlations were observed between jump height and RSI, concentric kinetic energy, peak power, concentric work, and concentric displacement. Significant correlations were observed between RSI and jump time, peak power, unload Fz, eccentric work, eccentric rate of force development (RFD), amortization Fz, amortization time, second Fz peak, average concentric Fz, and concentric displacement. Significant correlations were observed between jump time and unload Fz, eccentric work, eccentric RFD, amortization Fz, amortization time, average concentric Fz, and concentric work. In conclusion, jump height correlated with variables derived from the concentric phase only (work, power, and displacement), whereas Fz variables from the unloading, eccentric, amortization, and concentric phases correlated highly with RSI and jump time. These observations demonstrate the importance of countermovement Fz characteristics for time-sensitive CMJ performance measures. Researchers and practitioners should include RSI and jump time with jump height to improve their assessment of jump performance.

WEAK LINE QUASARS AT HIGH REDSHIFT: EXTREMELY HIGH ACCRETION RATES OR ANEMIC BROAD-LINE REGIONS?

International Nuclear Information System (INIS)

Shemmer, Ohad; Trakhtenbrot, Benny; Netzer, Hagai; Anderson, Scott F.; Brandt, W. N.; Schneider, Donald P.; Diamond-Stanic, Aleksandar M.; Fan Xiaohui; Lira, Paulina; Plotkin, Richard M.; Richards, Gordon T.; Strauss, Michael A.

2010-01-01

We present Gemini-North K-band spectra of two representative members of the class of high-redshift quasars with exceptionally weak rest-frame ultraviolet emission lines (WLQs), SDSS J114153.34+021924.3 at z = 3.55 and SDSS J123743.08+630144.9 at z = 3.49. In both sources, we detect an unusually weak broad Hβ line and place tight upper limits on the strengths of their [O III] lines. Virial, Hβ-based black hole mass determinations indicate normalized accretion rates of L/L Edd =0.4 for these sources, which is well within the range observed for typical quasars with similar luminosities and redshifts. We also present high-quality XMM-Newton imaging spectroscopy of SDSS J114153.34+021924.3 and find a hard-X-ray photon index of Γ = 1.91 +0.24 -0.22 , which supports the virial L/L Edd determination in this source. Our results suggest that the weakness of the broad emission lines in WLQs is not a consequence of an extreme continuum-emission source but instead due to abnormal broad emission line region properties.

Effect of drop jump technique on the reactive strength index.

Science.gov (United States)

Struzik, Artur; Juras, Grzegorz; Pietraszewski, Bogdan; Rokita, Andrzej

2016-09-01

The basic drill of plyometric training aimed at improving lower limb power and jump height is a drop jump. This exercise can be performed using different techniques, which substantially affects jump variables. Therefore, the aim of this study was to compare the values of the reactive strength index (RSI) for countermovement drop jumps (CDJs) and bounce drop jumps (BDJs). The study was carried out in a group of 8 male youth basketball players. The tests were conducted using the AMTI BP600900 force plate to measure ground reaction forces and the Noraxon MyoMotion system to record kinematic data. Each player performed two CDJs and two BDJs from the height of 15, 30, 45 and 60 cm. The RSI was calculated as a ratio of jump height and contact time. Moreover, the RSI was determined for the amortization and take-off phases separately. Significant differences (p jumps from 30, 45 and 60 cm. Differences in RSI values for jumps from 15 cm were not significant. Furthermore, CDJ height values were significantly higher (p jump technique that is commonly performed by basketball players.

Collision strengths for dipole-allowed transitions in S II

International Nuclear Information System (INIS)

Ho, Y.K.; Henry, R.J.W.

1990-01-01

Calculations of collision strengths for electron-impact excitations of S II from the ground state 3p3 4S0 to excited states 3p4 4P, 3d 4F, 3d 4D, 4s 4P, and 3d 4P were carried out using the R-matrix code described by Berrington et al. (1978) and the NIEM code described by Henry et al. (1981). Results are presented for the thermally averaged collision strengths for the five-state and six-state calculations. Convergence behaviors were examined by comparison with the six-state calculations and the previously obtained two-state calculations. Uncertainties for these transitions were estimated to be within 20 percent, except for the 4S0 - 3p4 4P transition in which a 40 percent uncertainty was estimated. 22 refs

Optimization Of Bleaching Parameters By Whiteness Index And Bursting Strength Of Knitted Cotton Fabric

Directory of Open Access Journals (Sweden)

Abu Naser Md. Ahsanul Haque

2015-04-01

Full Text Available Abstract The study comprises the effect of different bleaching parameters on scoured single jersey cotton fabrics. Three different concentrations 1.8 gL 2.0 gL and 2.2 gL taken from 5 stock solution of hydrogen peroxide were considered for the experiment. In each concentration bleaching was performed in four individual temperatures 78C 88C 98C and 108C. In each of the temperatures bleaching were continued for four individual time period 20 30 40 and 50 minutes. The weight of sample fabric was 12.5 grams and 110 liquor ratio was maintained in each operation. The bleached samples were tested in a reflectance spectrophotometer datacolor 650 and also their bursting strengths were found from an Autoburst instrument following ISO 13038-1 method. The results show that bursting strength and whiteness index have an inverse relation between themselves. For the nominated concentrations of peroxide 88C to 98C temperature with 30 to 40 minutes time duration is suggested as the optimum bleaching parameter for knitted cotton fabric.

Refractive index effects on the oscillator strength and radiative decay rate of 2,3-diazabicyclo[2.2.2]oct-2-ene.

Science.gov (United States)

Mohanty, Jyotirmayee; Nau, Werner M

2004-01-01

The photophysical properties of 2,3-diazabicyclo[2.2.2]oct-2-ene (DBO) were determined in 15 solvents, two supramolecular hosts (cucurbit[7]uril and beta-cyclodextrin) as well as in the gas phase. The oscillator strength and radiative decay rate of DBO as a function of refractive index i.e. polarizability have been analyzed. The oscillator strength increases by a factor of 10 upon going from the gas phase to the most polarizable carbon disulfide, while the corresponding radiative decay rates increase by a factor of 40. There is a good empirical correlation between the oscillator strength of the weakly allowed n,pi* transition of DBO and the reciprocal bulk polarizability, which can be employed to assess the polarizability of unknown microheterogeneous environments. A satisfactory correlation between the radiative decay rate and the square of the refractive index is also found, as previously documented for chromophores with allowed transitions. However, the correlation improves significantly when the oscillator strength is included in the correlation, which demonstrates the importance of this factor in the Strickler-Berg equation for chromophores with forbidden or weakly allowed transitions, for which the oscillator strength may be strongly solvent dependent. The radiative decay rate of DBO in two supramolecular assemblies has been determined, confirming the very low polarizability inside the cucurbituril cavity, in between perfluorohexane and the gas phase. The fluorescence quantum yield of DBO in the gas phase has been remeasured (5.1 +/- 0.5%) and was found to fall one full order of magnitude below a previously reported value.

Atomic data and spectral line intensities for Ne III

CERN Document Server

Bhatia, A K; Landi, E

2003-01-01

Electron impact collision strengths, energy levels, oscillator strengths and spontaneous radiative decay rates are calculated for Ne III. The configurations used are 2s sup 2 2p sup 4 , 2s2p sup 5 , 2s sup 2 2p sup 3 3s, and 2s sup 2 2p sup 3 3d giving rise to 57 fine-structure levels in intermediate coupling. Collision strengths are calculated at five incident energies, 5, 15, 25, 35, and 45 Ry. Excitation rate coefficients are calculated by assuming a Maxwellian electron velocity distribution at an electron temperature of logT sub e (K)=5.0, corresponding to maximum abundance of Ne III. Using the excitation rate coefficients and the radiative transition rates, statistical equilibrium equations for level populations are solved at electron densities covering the range of 10 sup 8 -10 sup 1 sup 4 cm sup - sup 3. Relative spectral line intensities are calculated. Proton excitation rates between the lowest three levels have been included in the statistical equilibrium equations. The predicted Ne III line intensi...

ECONOMETRIC’S MODEL: THE DEPENDENCE OF PFTS INDEX FROM ECONOMICS RANKS

Directory of Open Access Journals (Sweden)

K. Cherkashyna

2013-11-01

Full Text Available Dynamics of stock index is an indicator of market efficiency. We use the strong form of market efficiency, where prices reflect all available information, – both public and private. National index PFTS and main world indexes such as Dow Jones industrial, Standard & Poor’s 500, Nasdaq composite, Japan’s Nikkei index, Hong Kong’s Hang Seng index are very volatility. Last week all of the major U.S. stock indexes were in the red. Data dependence index PFTS from many exogenous and internal factors is analyzed in the article. The main exogenous factors are Dow Jones industrial, Nasdaq composite, growth rate of world GDP, price of gold, price of oil. The main internal factors are the exchange rate, the international investment position of Ukraine, the external debt of Ukraine. Index PFTS is malleable from the international investment position, the exchange rate and the price of gold. It is very difficult to forecast the dynamic of stock index. There is an approximation error. It is 6,82%. It is less than 10% and it is allowable. The econometric model makes it possible to predict the dynamics of the PFTS on the next years. But we must have in mind asymmetry of information and moral hazard.

New composite index based on midlatency auditory evoked potential and electroencephalographic parameters to optimize correlation with propofol effect site concentration - Comparison with bispectral index and solitary used fast extracting auditory evoked potential index

NARCIS (Netherlands)

Vereecke, HEM; Vasquez, PM; Jensen, EW; Thas, O; Vandenbroecke, R; Mortier, EP; Struys, MMRF

Background: This study investigates the accuracy of a composite index, the A-Line (R) auditory evoked potentials index version 1.6 (AAI(1.6); Danmeter A/S, Odense, Denmark), as a measure of cerebral anesthetic drug effect in a model for predicting a calculated effect site concentration of propofol

46 CFR 45.107 - Strength of hull.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Strength of hull. 45.107 Section 45.107 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.107 Strength of hull. The general structural strength of the hull must be sufficient for the...

Collision strengths for the excitation of lithium- and boron-like ions by electron impact

International Nuclear Information System (INIS)

Goett, S.J.

1983-01-01

The theory of collision strengths of highly charged ions is presented in terms of the R-matrix formalism by utilizing time-dependent perturbation theory. This theory is then applied to the general case of an ion with three valence electrons. The theory is general enough to admit the possiblity of three equivalent electrons. The effects of configuration interaction and intermediate coupling are incorporated through the mixing coefficients calculated by diagonalizing the perturbation matrix. This matrix is formed by taking into account the electron-electron electrostatic interaction as well as all first order relativistic corrections. The dipole radiative line strengths are also calculated using these mix coefficients. The line strengths are needed for the Coulomb-Bethe approximation which estimates the contributions to the collision strengths from large values of the impact electron's orbital angular momentum. All the above quantities are calculated in both the LS and jj coupling schemes. This dual calculation provides useful information about the mixing of the states present, as well as serving as a valuable check on the development of the theory and the coding of the computer programs. An application is made to the calculation of transition energies, line strengths and collision strengths of transitions from all lower states with a configuration of 1s 2 2I to all upper states with a configuraiton of 1s2I/sub a/'2I/sub b/'

Multi-band Microwave Antennas and Devices based on Generalized Negative-Refractive-Index Transmission Lines

Science.gov (United States)

Ryan, Colan Graeme Matthew

Focused on the quad-band generalized negative-refractive-index transmission line (G-NRI-TL), this thesis presents a variety of novel printed G-NRI-TL multi-band microwave device and antenna prototypes. A dual-band coupled-line coupler, an all-pass G-NRI-TL bridged-T circuit, a dual-band metamaterial leaky-wave antenna, and a multi-band G-NRI-TL resonant antenna are all new developments resulting from this research. In addition, to continue the theme of multi-band components, negative-refractive-index transmission lines are used to create a dual-band circularly polarized transparent patch antenna and a two-element wideband decoupled meander antenna system. High coupling over two independently-specified frequency bands is the hallmark of the G-NRI-TL coupler: it is 0.35lambda0 long but achieves approximately -3 dB coupling over both bands with a maximum insertion loss of 1 dB. This represents greater design flexibility than conventional coupled-line couplers and less loss than subsequent G-NRI-TL couplers. The single-ended bridged-T G-NRI-TL offers a metamaterial unit cell with an all-pass magnitude response up to 8 GHz, while still preserving the quad-band phase response of the original circuit. It is shown how the all-pass response leads to wider bandwidths and improved matching in quad-band inverters, power dividers, and hybrid couplers. The dual-band metamaterial leaky-wave antenna presented here was the first to be reported in the literature, and it allows broadside radiation at both 2 GHz and 6 GHz without experiencing the broadside stopband common to conventional periodic antennas. Likewise, the G-NRI-TL resonant antenna is the first reported instance of such a device, achieving quad-band operation between 2.5 GHz and 5.6 GHz, with a minimum radiation efficiency of 80%. Negative-refractive-index transmission line loading is applied to two devices: an NRI-TL meander antenna achieves a measured 52% impedance bandwidth, while a square patch antenna incorporates

Collective properties of drip-line nuclei

Energy Technology Data Exchange (ETDEWEB)

Hamamoto, I. [Univ. of Lund (Sweden); Sagawa, H. [Univ. of Aizu, Fukushima (Japan)

1996-12-31

Performing the spherical Hartree-Fock (HF) calculations with Skyrme interactions and, then, using RPA solved in the coordinate space with the Green`s function method, the authors have studied the effect of the unique shell structure as well as the very low particle threshold on collective modes in drip line nuclei. In this method a proper strength function in the continuum is obtained, though the spreading width of collective modes is not included. They have examined also one-particle resonant states in the obtained HF potential. Unperturbed particle-hole (p-h) response functions are carefully studied, which contain all basic information on the exotic behaviour of the RPA strength function in drip line nuclei.

Assessing Reactive Strength Measures in Jumping and Hopping Using the Optojump™ System

Directory of Open Access Journals (Sweden)

Healy Robin

2016-12-01

Full Text Available The aim of this study was to assess the concurrent validity of the Optojump™ system (Microgate, Bolzano, Italy versus a force platform in the estimation of temporal and reactive strength measures. In two separate investigations, twenty physically active males performed double-leg and single-leg drop jumps from a box height of 0.3 m and a 10 s vertical bilateral hopping test. Contact time, flight time and total time (the sum of contact and flight time were concurrently assessed during single and double-leg drop jumps and during hopping. Jump height, the reactive strength index and the reactive strength ratio were also calculated from contact time and flight time. Despite intraclass correlation coefficients (ICCs for all variables being close to 1 (ICC > 0.975, a significant overestimation was found in contact time (0.005 ± 0.002 s and underestimations in flight time (0.005 ± 0.003 s, the reactive strength index (0.04 ± 0.02 m·s-1 and the reactive strength ratio (0.07 ± 0.04. Overestimations in contact time and underestimations in flight time were attributed to the physical design of the Optojump™ system as the transmitter and receiver units were positioned 0.003 m above the floor level. The Optojump™ demonstrated excellent overall temporal validity with no differences found between systems for total time. Coaches are advised to be consistent with the instrumentation used to assess athletes, however, in the case of comparison between reactive strength values collected with the Optojump™ and values collected with a force platform, regression equations are provided.

Effects of two soft drinks on shear bond strength and adhesive remnant index of orthodontic metal brackets.

Science.gov (United States)

Sajadi, Soodabeh Sadat; Eslami Amirabadi, Gholamreza; Sajadi, Sepideh

2014-07-01

Bond failure of brackets during orthodontic treatment is a common problem; which results in treatment interference, increased treatment time and prolonged clinical time for rebonding of failed brackets. The purpose of this study was to evaluate the effects of Coca-Cola and a non-alcoholic beer on the shear bond strength and adhesive remnant index (ARI) of orthodontic metal brackets in vitro. Eighty intact human premolars were divided into two experimental groups of Coca-Cola and non-alcoholic beer (Istak), and a control group of artificial saliva. Over a period of thirty days, the test groups were immersed in the respective soft drinks for 5 minutes, twice a day. For the remainder of the time, they were kept in artificial saliva at 37°C. The control group was stored in artificial saliva during the experiment. All samples were subjected to shearing forces using Universal Testing Machine. ARI was determined with a stereomicroscope at ×12 magnification. The data of shear bond strength were statistically analyzed by one-way ANOVA and Tukey's Post-Hoc test and the data of ARI scores were analyzed by Kruskal-Wallis test. No significant difference was observed in ARIs of the three groups (P≤ 0.552). The shear bond strength of Coke group was significantly lower than that of the two other groups (P≤ 0.035); but there was no significant difference between the shear bond strength of Istak and the control group (P≤ 0.999). Coca-Cola decreased the shear bond strength of orthodontic brackets.

Comparison of residual strength-grounding damage index diagrams for tankers produced by the ALPS/HULL ISFEM and design formula method

Directory of Open Access Journals (Sweden)

Do Kyun Kim

2013-03-01

Full Text Available This study compares the Residual ultimate longitudinal strength – grounding Damage index (R-D diagrams produced by two analysis methods: the ALPS/HULL Intelligent Supersize Finite Element Method (ISFEM and the design formula (modified Paik and Mansour method – used to assess the safety of damaged ships. The comparison includes four types of double-hull oil tankers: Panamax, Aframax, Suezmax and VLCC. The R-D diagrams were calculated for a series of 50 grounding scenarios. The diagrams were efficiently sampled using the Latin Hypercube Sampling (LHS technique and comprehensively analysed based on ship size. Finally, the two methods were compared by statistically analysing the differences between their grounding damage indices and ultimate longitudinal strength predictions. The findings provide a useful example of how to apply the ultimate longitudinal strength analysis method to grounded ships.

Systematic review on strength training in Parkinson’s disease: an unsolved question

Directory of Open Access Journals (Sweden)

Ramazzina I

2017-03-01

Full Text Available Ileana Ramazzina,1 Benedetta Bernazzoli,2 Cosimo Costantino1 1Department of Biomedical, Biotechnological and Translational Sciences, 2Department of Clinical and Experimental Medicine, Graduate School of Rehabilitation and Physical Medicine, University of Parma, Parma, Italy Abstract: The purpose of this study was to investigate the effectiveness of strength training, performed against a different resistance from body weight, in improving motor and nonmotor symptoms in patients with Parkinson’s disease (PD. The following electronic databases were searched: PubMed, Physiotherapy Evidence Database, Cochrane Central Register of Controlled Trials, Scopus, and Web of Science. The review was conducted and reported in accordance with the PRISMA statement. Thirteen high-quality randomized controlled trials were included. Strength training performed against external resistance is well tolerated and appears to be a suitable physical activity to improve both physical parameters and quality of life parameters of PD subjects. However, although the study intervention included strength training, only a few selected studies assessed the improvement of muscle strength. Despite the encouraging results, it is difficult to establish a correlation between strength training and the improvements made. Our review highlights the lack of common intent in terms of study design and the presence of different primary and secondary outcomes. Accordingly, further studies are needed to support the beneficial effects of different types of strength training in PD subjects and to underline the superiority of strength training in PD patients with respect to other training. Keywords: Parkinson’s disease, strength training, muscle strength

Estimation of Physiological Cost Index as an Energy Expenditure Index using MacGregor’s Equation

Directory of Open Access Journals (Sweden)

Binaya SJB Rana

2015-09-01

Full Text Available Introduction: Physical activity and energy expenditure can be quantified by measuring heart rate, oxygen uptake and respiratory quotient. The Physiological Cost Index (PCI proposed by MacGregor is a simple and straightforward method to estimate the energy expenditure index. Here, we aim to estimate the energy expenditure among young Asian population using MacGregor’s equation. Methods: A total of 50 young randomly selected healthy females performed 50m, 100m and 150m walking test at their self-selected preferred speed. The physiological cost index values for 100 m walk at speeds slower and faster than the preferred speed were also obtained. The physiological cost index during exercise was calculated using MacGregor’s equation considering heart rate and speed of walking over the varying distances. Results: The PCI values on three different distances are consistent during self selected preferred speed. The PCI estimation on second and third tests for all three distances walked consistently reproducible. However for each distance walked, the first test the PCI was significantly higher than the second and third test values. The PCI values increased significantly when subjects walked either slower (p = 0.02 or faster (p = 0.001 than their normal preferred speed. Conclusion: The physiological cost index values were similar for varying distances walks. The PCI was the least at the preferred speed of walking and increased when the subjects either walked slower or faster than the preferred speed. The first estimation was higher than subsequent estimations. Keywords: energy expenditure index; exercise; physiological cost index. | PubMed

PREDICTION OF GEOMAGNETIC STORM STRENGTH FROM INNER HELIOSPHERIC IN SITU OBSERVATIONS

Energy Technology Data Exchange (ETDEWEB)

Kubicka, M.; Möstl, C.; Amerstorfer, T.; Boakes, P. D.; Törmänen, O. [Space Research Institute, Austrian Academy of Sciences, 8042 Graz (Austria); Feng, L. [Purple Mountain Observatory, Chinese Academy of Sciences, West Beijing Road 2 Nanjing, 210008 (China); Eastwood, J. P., E-mail: christian.moestl@oeaw.ac.at [Space and Atmospheric Physics, The Blackett Laboratory, Imperial College London, London SW7 2AZ (United Kingdom)

2016-12-20

Prediction of the effects of coronal mass ejections (CMEs) on Earth strongly depends on knowledge of the interplanetary magnetic field southward component, B{sub z}. Predicting the strength and duration of B{sub z} inside a CME with sufficient accuracy is currently impossible, forming the so-called B{sub z} problem. Here, we provide a proof-of-concept of a new method for predicting the CME arrival time, speed, B{sub z}, and resulting disturbance storm time ( Dst ) index on Earth based only on magnetic field data, measured in situ in the inner heliosphere (<1 au). On 2012 June 12–16, three approximately Earthward-directed and interacting CMEs were observed by the Solar Terrestrial Relations Observatory imagers and Venus Express (VEX) in situ at 0.72 au, 6° away from the Sun–Earth line. The CME kinematics are calculated using the drag-based and WSA–Enlil models, constrained by the arrival time at VEX , resulting in the CME arrival time and speed on Earth. The CME magnetic field strength is scaled with a power law from VEX to Wind . Our investigation shows promising results for the Dst forecast (predicted: −96 and −114 nT (from 2 Dst models); observed: −71 nT), for the arrival speed (predicted: 531 ± 23 km s{sup −1}; observed: 488 ± 30 km s{sup −1}), and for the timing (6 ± 1 hr after the actual arrival time). The prediction lead time is 21 hr. The method may be applied to vector magnetic field data from a spacecraft at an artificial Lagrange point between the Sun and Earth or to data taken by any spacecraft temporarily crossing the Sun–Earth line.

Research on cylindrical indexing cam’s unilateral machining

Directory of Open Access Journals (Sweden)

Junhua Chen

2015-08-01

Full Text Available The cylindrical cam ridge of the indexer is a spatial curved surface, which is difficult to design and machine. The cylindrical cam has some defects after machining because conventional machining methods have inaccuracies. This article aims at proposing a precise way to machine an indexing cam, using basic motion analysis and analytic geometry approach. Analytical methodology is first applied in the cam’s motion analysis, to obtain an error-free cam follower’s trajectory formula, and then separate the continuous trajectory curve by thousandth resolution, to create a three-dimensional discrete trajectory curve. Planar formulae and spherical formulae can be built on the loci. Based on the machine principle, the cutting cutter’s position and orientation will be taken into account. This article calculates the formula set as presented previously and obtains the ultimate cutter path coordinate value. The new error-free cutter path trajectory is called the unilateral machining trajectory. The earned results will compile into numerical control processing schedule. This processing methodology gives a convenient and precision way to manufacture a cylindrical indexing cam. Experimental results are also well supported.

Isolation, Characterization, and Establishment of Spontaneously Immortalized Cell Line HRPE-2S With Stem Cell Properties.

Science.gov (United States)

Shams Najafabadi, Hoda; Soheili, Zahra-Soheila; Samiei, Shahram; Ahmadieh, Hamid; Ranaei Pirmardan, Ehsan; Masoumi, Maryam

2017-10-01

The retinal pigment epithelium is a monolayer of highly specialized pigmented cells located between the neural retina and the Bruch's membrane of the choroid. RPE cells play a crucial role in the maintenance and function of the underlying photoreceptors. This study introduces a spontaneously arising human retinal pigment epithelial cell line, HRPE-2S, which was isolated from primary RPE cell culture of 2 days old male donor. We characterized morphology and functional properties of the new cell line. The immortalized cell line was maintained in culture for more than 70 passages and 240 divisions. The average doubling time of the cells was approximately 22 h and got freezed at 26th passage. The cell line expressed RPE-specific markers RPE65 and cell junction protein ZO1 as an epithelial cell marker. It also expressed CHX10, PAX6, Nestin, SOX2 as stem and retinal progenitor cell markers. Ki67 as a marker of cell proliferation was expressed in all HRPE-2S cells. It represented typical epithelial cobblestone morphology and did not phenotypically change through several passages. Stem cell-like aggregations (neurospheres) were observed in SEM microscopy. The cells represented high mitotic index. They could be viable under hypoxic conditions and serum deprivation. According to functional studies, the cell line exhibited stem cell-like behaviors with particular emphasis on its self-renewal capacity. LDH isoenzymes expression pattern confirmed the same cellular source for both of the HRPE-2S cells and primary RPE cells. Characteristics of HRPE-2S cells promise it as an in vitro model for RPE stem cell-based researches. J. Cell. Physiol. 232: 2626-2640, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Development of high-strength heavy-wall sour-service seamless line pipe for deep water by applying inline heat treatment

Energy Technology Data Exchange (ETDEWEB)

Arai, Y.; Kondo, K.; Hamada, M.; Hisamune, N.; Murao, N.; Murase, T.; Osako, H. [Sumitomo Metal Industries Ltd., Tokyo (Japan)

2004-07-01

This paper provided details of a new high-strength heavy-wall sour service seamless line pipe developed for use in deep water applications. Pig iron was processed in a blast furnace and refined. Molten steel was degassed to reduce impurities and poured into a continuous caster with a round mold. Billets were then heated in a walking-beam furnace and then pierced to form a hollow shell. The shell was then rolled to a specific thickness in a compact mandrel mill and rolled to a specified outer diameter by an extracting sizer. A heating furnace was used to improve the uniformity of the pipes. The heated pipes were then moved to a cooling zone, then rotated quickly while a high-pressured jet flow was injected inside the pipe at the same time as a slit laminar flow was applied to the outside of the pipe. Higher strength was achieved by using the high performance quenching device. It was noted that while pipes manufactured using the inline heat treatment process were able to achieve higher strengths, toughness was reduced. Metallurgical tests were conducted to improve the toughness value of the seamless pipe. Both the microstructure and the fracture surface of test specimens were examined using scanning electron microscopy. Results of the tests showed that lowering sulphur (S) and titanium (Ti) content improved the toughness properties of the pipes. It was concluded that control of microalloys is important to secure improved toughness for pipes manufactured using inline heat treatments. 5 tabs., 12 figs.

Dependence of transmittance and group index on the coupling strength between constituents of a metamaterial

International Nuclear Information System (INIS)

Thuy Vu, Tran Thanh; Lee, Young Pak; Nguyen, Thanh Tung; Rhee, Joo Yull; Vu, Dinh Lam

2011-01-01

Recent studies on the coupling effects between constituent elements of metamaterials have opened up a new gateway to many fascinating electromagnetic properties and functionalities that cannot be explained by the uncoupled point of view. In this work, we numerically investigated, in a THz regime, the coupling between a cut wire and a split-ring resonator, which gives rise to an interesting phenomenon—the so-called electromagnetically induced transparency-like effect. The trade-off between the maximum transmittance of the transmission window and the group index, which depends on the coupling strength between constituent elements, was systematically studied. Furthermore, by characterizing this trade-off by the transmittance-delay product (figure of merit), a criterion for slow-light applications was provided

Volatility Degree Forecasting of Stock Market by Stochastic Time Strength Neural Network

Directory of Open Access Journals (Sweden)

Haiyan Mo

2013-01-01

Full Text Available In view of the applications of artificial neural networks in economic and financial forecasting, a stochastic time strength function is introduced in the backpropagation neural network model to predict the fluctuations of stock price changes. In this model, stochastic time strength function gives a weight for each historical datum and makes the model have the effect of random movement, and then we investigate and forecast the behavior of volatility degrees of returns for the Chinese stock market indexes and some global market indexes. The empirical research is performed in testing the prediction effect of SSE, SZSE, HSI, DJIA, IXIC, and S&P 500 with different selected volatility degrees in the established model.

Lightweight Potential of Welded High-strength Steel Joints from S700 Under Constant and Variable Amplitude Loading by High-frequency Mechanical Impact (HFMI) Treatment

OpenAIRE

Yıldırım, Halid Can; Marquis, Gary; Sonsino, Cetin Morris

2015-01-01

Investigations with longitudinal stiffeners of the steel grade S700 under fully-reversed, constant amplitude loading and under variable amplitude loading with a straight-line spectrum show impressive fatigue strength improvement by high-frequency mechanical impact (HFMI) treatment. However, the degree of improvement was for variable amplitude loading lower when compared to constant amplitude loading due to local plasticity which occurs during larger load levels and consequently reduces the be...

Etnografia on e off-line: cibercafés em Trinidad

Directory of Open Access Journals (Sweden)

Daniel Miller

2004-06-01

Full Text Available O presente artigo questiona pressupostos sobre a distinção, comum na pesquisa de Internet, entre on-line e off-line. Várias pesquisas presumiram a "virtualidade", bem como uma forte divisão entre o on-line e o off-line como sendo um dado e um ponto de partida metodológico e analítico em pesquisa. Argumentamos que quando se aborda o uso de fato da Internet a partir de uma abordagem etnográfica, uma tal distinção se revela como um feito social altamente contingente: alguns atores empregam grandes habilidades para estabelecer uma distinção clara entre on-line e off-line em suas práticas de Internet; em outros, tal distinção não tem sentido, ou não é desejável, e tais distinções não são de fato estabelecidas. Utilizamos uma comparação entre cibercafés em Trinidad para demonstrar essa variabilidade e a ampla gama de diferentes relações on-line/off-line que são realmente observadas. Nós relacionamos esse material com a questão mais geral de se estabelecer "contextos" na pesquisa etnográfica.This article interrogates assumptions about the on-line/off-line distinction in internet research. Much research has presumed "virtuality" and a strong division between the on-line and the off-line as a methodological and analytical given and starting point for research. We argue that when actual internet use is approached from an ethnographic perspective, this distinction turns out to be a highly contingent social accomplishment: some actors deploy great skill to establish a sharp on-line/off-line distinction in their internet practices; for others, it is meaningless or undesirable and the distinctions is not established in reality. A comparison of cybercafes in Trinidad is used to demonstrate this variability and the wide range of different on-line/off-line relationships that are in fact observed. We relate this material to the overall issue of establishing "contexts" in ethnographic research.

Importance of tie strengths in the prisoner's dilemma game on social networks

Energy Technology Data Exchange (ETDEWEB)

Xu, Bo, E-mail: xubosuper@163.com [Department of Information Systems, School of Economics and Management, Beihang University (China); Liu, Lu; You, Weijia [Department of Information Systems, School of Economics and Management, Beihang University (China)

2011-06-13

Though numerous researches have shown that tie strengths play a key role in the formation of collective behavior in social networks, little work has been done to explore their impact on the outcome of evolutionary games. In this Letter, we studied the effect of tie strength in the dynamics of evolutionary prisoner's dilemma games by using online social network datasets. The results show that the fraction of cooperators has a non-trivial dependence on tie strength. Weak ties, just like previous researches on epidemics and information diffusion have shown, play a key role by the maintenance of cooperators in evolutionary prisoner's dilemma games. -- Highlights: → Tie strength is used to measure heterogeneous influences of different pairs of nodes. → Weak ties play a role in maintaining cooperation in prisoner's dilemma games. → Micro-dynamics of nodes are illustrated to explain the conclusion.

Assessing the strength of cardiac and sympathetic baroreflex controls via transfer entropy during orthostatic challenge

Science.gov (United States)

Porta, Alberto; Marchi, Andrea; Bari, Vlasta; De Maria, Beatrice; Esler, Murray; Lambert, Elisabeth; Baumert, Mathias

2017-05-01

The study assesses the strength of the causal relation along baroreflex (BR) in humans during an incremental postural challenge soliciting the BR. Both cardiac BR (cBR) and sympathetic BR (sBR) were characterized via BR sequence approaches from spontaneous fluctuations of heart period (HP), systolic arterial pressure (SAP), diastolic arterial pressure (DAP) and muscle sympathetic nerve activity (MSNA). A model-based transfer entropy method was applied to quantify the strength of the coupling from SAP to HP and from DAP to MSNA. The confounding influences of respiration were accounted for. Twelve young healthy subjects (20-36 years, nine females) were sequentially tilted at 0°, 20°, 30° and 40°. We found that (i) the strength of the causal relation along the cBR increases with tilt table inclination, while that along the sBR is unrelated to it; (ii) the strength of the causal coupling is unrelated to the gain of the relation; (iii) transfer entropy indexes are significantly and positively associated with simplified causality indexes derived from BR sequence analysis. The study proves that causality indexes are complementary to traditional characterization of the BR and suggests that simple markers derived from BR sequence analysis might be fruitfully exploited to estimate causality along the BR. This article is part of the themed issue `Mathematical methods in medicine: neuroscience, cardiology and pathology'.

Transcriptomic analysis of fiber strength in upland cotton chromosome introgression lines carrying different Gossypium barbadense chromosomal segments.

Directory of Open Access Journals (Sweden)

Lei Fang

Full Text Available Fiber strength is the key trait that determines fiber quality in cotton, and it is closely related to secondary cell wall synthesis. To understand the mechanism underlying fiber strength, we compared fiber transcriptomes from different G. barbadense chromosome introgression lines (CSILs that had higher fiber strengths than their recipient, G. hirsutum acc. TM-1. A total of 18,288 differentially expressed genes (DEGs were detected between CSIL-35431 and CSIL-31010, two CSILs with stronger fiber and TM-1 during secondary cell wall synthesis. Functional classification and enrichment analysis revealed that these DEGs were enriched for secondary cell wall biogenesis, glucuronoxylan biosynthesis, cellulose biosynthesis, sugar-mediated signaling pathways, and fatty acid biosynthesis. Pathway analysis showed that these DEGs participated in starch and sucrose metabolism (328 genes, glycolysis/gluconeogenesis (122 genes, phenylpropanoid biosynthesis (101 genes, and oxidative phosphorylation (87 genes, etc. Moreover, the expression of MYB- and NAC-type transcription factor genes were also dramatically different between the CSILs and TM-1. Being different to those of CSIL-31134, CSIL-35431 and CSIL-31010, there were many genes for fatty acid degradation and biosynthesis, and also for carbohydrate metabolism that were down-regulated in CSIL-35368. Metabolic pathway analysis in the CSILs showed that different pathways were changed, and some changes at the same developmental stage in some pathways. Our results extended our understanding that carbonhydrate metabolic pathway and secondary cell wall biosynthesis can affect the fiber strength and suggested more genes and/or pathways be related to complex fiber strength formation process.

Development of Ferrium S53 High-Strength, Corrosion-Resistant Steel

Science.gov (United States)

2009-01-01

or any other high-strength steel. No special tools or grinding wheels are required. The only significant differences with S53 are  Machining... runout point and ** point) Fit for 4330 in Air (w/o runout points) Fit for S53 in Salt Fit for 300M in Salt Fit for 4330 in Salt MIL HNBK 5 for 300M in

Strength and cardiometabolic risk in young adults: The mediator role of aerobic fitness and waist circumference.

Science.gov (United States)

Díez-Fernández, A; Martínez-Vizcaíno, V; Torres-Costoso, A; Cañete García-Prieto, J; Franquelo-Morales, P; Sánchez-López, M

2018-02-22

The aim of this study was to analyze the mediation role of cardiorespiratory fitness and waist circumference in the association between muscular strength and cardiometabolic risk. A cross-sectional study involved first-year college students (n = 370) from a Spanish public university was performed. We measured weight, height, waist circumference, blood pressure, biochemical variables, maximum handgrip strength assessment, and cardiorespiratory fitness. We calculated handgrip dynamometry/weight and a previously validated cardiometabolic risk index. Analysis of covariance models was conducted to test differences in cardiometabolic risk values across muscular strength, cardiorespiratory fitness, and waist circumference categories, controlling for confounders. Hayes' PROCESS macro was used for the multiple mediation analysis. The relationship between muscular strength and cardiometabolic risk did not remain significant (c' = 1.76 [1.4]; P > .05) in a multiple serial bootstrapped mediation model including cardiorespiratory fitness and waist circumference as mediators when controlling for age and sex. According to the indirect effect, the significant paths in the model mediating this relationship between muscular strength and cardiometabolic risk index were as follows: muscular strength → waist circumference → cardiometabolic risk index (-4.899; 95% CI: -6.690; -3.450) and muscular strength → cardiorespiratory fitness → waist circumference → cardiometabolic risk index (-0.720; 95% CI: -1.316; -0.360). Both cardiorespiratory fitness and waist circumference mediate the association between muscular strength and cardiometabolic risk in young adults. Thus, our results place cardiorespiratory fitness and waist circumference as the main targets of physical activity programmes aimed at preventing cardiometabolic diseases. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Grip Strength Survey Based on Hand Tool Usage

Directory of Open Access Journals (Sweden)

Erman ÇAKIT

2016-12-01

Full Text Available Hand grip strength is broadly used for performing tasks involving equipment in production and processing activities. Most professionals in this field rely on grip strength to perform their tasks. There were three main aims of this study: i determining various hand grip strength measurements for the group of hand tool users, ii investigating the effects of height, weight, age, hand dominance, body mass index, previous Cumulative Trauma Disorder (CTD diagnosis, and hand tool usage experience on hand grip strength, and iii comparing the obtained results with existing data for other populations. The study groups comprised 71 healthy male facility workers. The values of subjects’ ages was observed between 26 and 74 years. The data were statistically analyzed to assess the normality of data and the percentile values of grip strength. The results of this study demonstrate that there were no significance differences noted between dominant and non-dominant hands. However, there were highly significant differences between the CTD group and the other group. Hand grip strength for the dominant hand was positively correlated to height, weight, and body mass index, and negatively correlated to age and tool usage experience. Hand dominance, height, weight, body mass index, age and tool usage experience should be considered when establishing normal values for grip strength.

Effect of drop jump technique on the reactive strength index

Directory of Open Access Journals (Sweden)

Struzik Artur

2016-09-01

Full Text Available The basic drill of plyometric training aimed at improving lower limb power and jump height is a drop jump. This exercise can be performed using different techniques, which substantially affects jump variables. Therefore, the aim of this study was to compare the values of the reactive strength index (RSI for countermovement drop jumps (CDJs and bounce drop jumps (BDJs. The study was carried out in a group of 8 male youth basketball players. The tests were conducted using the AMTI BP600900 force plate to measure ground reaction forces and the Noraxon MyoMotion system to record kinematic data. Each player performed two CDJs and two BDJs from the height of 15, 30, 45 and 60 cm. The RSI was calculated as a ratio of jump height and contact time. Moreover, the RSI was determined for the amortization and take-off phases separately. Significant differences (p < 0.05 between RSI values for CDJs and BDJs were recorded for jumps from 30, 45 and 60 cm. Differences in RSI values for jumps from 15 cm were not significant. Furthermore, CDJ height values were significantly higher (p < 0.05 than the values recorded for BDJs. Times of contact, amortization and take-off during BDJs were significantly shorter (p < 0.05 than the respective values obtained for CDJs. Therefore, the use of the RSI to monitor plyometric training should be based on the drop jump technique that is commonly performed by basketball players.

Neutron source strength determination for on-line reactivity measurements

Energy Technology Data Exchange (ETDEWEB)

Hoogenboom, J.E.; Sluijs, A.R. van der

1988-01-01

A method is described to determine the effective neutron source strength in a nuclear reactor, which must be known when calculating the time-varying reactivity from inverse reactor kinetics for a reactor at low power. When for an initially subcritical reactor the reactivity is changed and kept constant after the change, the effective source strength can be determined from a linear regression of reactor power to a function proportional to the emission rate of delayed neutrons, which can be calculated from the reactor power history. In view of the relatively strong noise present in the reactor power signal at low power, a grouping method for the regression is preferred over the least-squares method. Experiments with a reactor simulator with known source strength showed good agreement. Application to actual reactor signals gave consistent and satisfactory results.

Laboratory oscillator strengths of Sc i in the near-infrared region for astrophysical applications

Science.gov (United States)

Pehlivan, A.; Nilsson, H.; Hartman, H.

2015-10-01

Context. Atomic data is crucial for astrophysical investigations. To understand the formation and evolution of stars, we need to analyse their observed spectra. Analysing a spectrum of a star requires information about the properties of atomic lines, such as wavelengths and oscillator strengths. However, atomic data of some elements are scarce, particularly in the infrared region, and this paper is part of an effort to improve the situation on near-IR atomic data. Aims: This paper investigates the spectrum of neutral scandium, Sc I, from laboratory measurements and improves the atomic data of Sc I lines in the infrared region covering lines in R, I, J, and K bands. Especially, we focus on measuring oscillator strengths for Sc I lines connecting the levels with 4p and 4s configurations. Methods: We combined experimental branching fractions with radiative lifetimes from the literature to derive oscillator strengths (f-values). Intensity-calibrated spectra with high spectral resolution were recorded with Fourier transform spectrometer from a hollow cathode discharge lamp. The spectra were used to derive accurate oscillator strengths and wavelengths for Sc I lines, with emphasis on the infrared region. Results: This project provides the first set of experimental Sc I lines in the near-infrared region for accurate spectral analysis of astronomical objects. We derived 63 log(gf) values for the lines between 5300 Å and 24 300 Å. The uncertainties in the f-values vary from 5% to 20%. The small uncertainties in our values allow for an increased accuracy in astrophysical abundance determinations.

Enriching the ECSI model using brand strength in the retail setting

Directory of Open Access Journals (Sweden)

Paraskevi Sarantidou

2017-10-01

Full Text Available Purpose - The purpose of this paper is to investigate the role of the retailer’s brand strength as a potential predictor of loyalty. It also examines the role of customer satisfaction (CS to the retailer’s loyalty as well as its impact on the retailer’s brand strength. Design/methodology/approach - The study was conducted in the grocery context and in a market under recession using the European Customer Satisfaction Index (ECSI model. Data were collected through a telephone survey from 2,000 participants responsible for the household grocery shopping with a quota of 250 respondents from each of the leading grocery retailers in Greece. A formative measurement model was developed and the collected data were analyzed using partial least square path modeling. Findings - The findings revealed that the strength of the retailer’s brand and CS influence retail loyalty and that brand strength mediate the strength of CS to loyalty. Results also suggested that the expectations and the perceptions toward the retailer’s product offering are the most important drivers of CS and loyalty. Thus, the study has proved the importance of the functional store attributes to CS and loyalty in the grocery store setting. Originality/value - Research examining the suitability of the ECSI model in the grocery setting and in a market under economic crisis is scarce. This paper addresses these shortcomings by examining a customer loyalty model which incorporates the brand strength construct and investigates the role of brand strength as a potential predictor of loyalty as well as the role of CS in the brand strength and loyalty.

Aumann and Serrano’s economic index of risk for sums of gambles

Directory of Open Access Journals (Sweden)

Minqiang Li

2014-12-01

Full Text Available We study Aumann and Serrano’s (2008 risk index for sums of gambles that are not dependent. If the dependent parts are similarly ordered, then the risk index of the sum is always larger than the minimum of the risk indices of the two gambles. For negative dependence, the risk index of the sum is always smaller than the maximum. The above results agree with our intuitions of risk diversification well. These result points out another attractive property of Aumann and Serrano’s risk index. These properties are potentially useful for risk assessment purposes of financial securities.

Probing the Physics of Narrow-line Regions in Active Galaxies. IV. Full Data Release of the Siding Spring Southern Seyfert Spectroscopic Snapshot Survey (S7)

Energy Technology Data Exchange (ETDEWEB)

Thomas, Adam D.; Dopita, Michael A.; Davies, Rebecca; Hampton, Elise; Kewley, Lisa; Banfield, Julie; Groves, Brent; Sutherland, Ralph [RSAA, Australian National University, Cotter Road, Weston Creek, ACT 2611 (Australia); Shastri, Prajval; Sairam, Lalitha [Indian Institute of Astrophysics, Sarjapur Road, Bengaluru 560034 (India); James, Bethan L. [Space Telescope Science Institute, 3700 San Martin Drive, Baltimore, MD 21218 (United States); Jin, Chichuan [Max-Planck-Institut für Extraterrestrische Physik, Garching (Germany); Juneau, Stéphanie [CEA-Saclay, DSM/IRFU/SAp, F-91191 Gif-sur-Yvette (France); Kharb, Preeti [National Centre for Radio Astrophysics—Tata Institute of Fundamental Research, Pune University Campus, Post Bag 3, Ganeshkhind Pune 411007 (India); Scharwächter, Julia [Gemini Observatory, Northern Operations Center, 670 N. A’ohoku Place, Hilo, Hawaii 96720 (United States); Shalima, P. [Regional Institute of Education, Manasagangotri, Mysore 570006 (India); Sundar, M. N. [Jain University, 3rd Block Jayanagar, Bengaluru 560011 (India); Zaw, Ingyin, E-mail: adam.thomas@anu.edu.au [New York University (Abu Dhabi), 70 Washington Sq. S, New York, NY 10012 (United States)

2017-09-01

We present the second and final data release of the Siding Spring Southern Seyfert Spectroscopic Snapshot Survey (S7). Data are presented for 63 new galaxies not included in the first data release, and we provide 2D emission-line fitting products for the full S7 sample of 131 galaxies. The S7 uses the WiFeS instrument on the ANU 2.3 m telescope to obtain spectra with a spectral resolution of R  = 7000 in the red (540–700 nm) and R  = 3000 in the blue (350–570 nm), over an integral field of 25 × 38 arcsec{sup 2} with 1 × 1 arcsec{sup 2} spatial pixels. The S7 contains both the largest sample of active galaxies and the highest spectral resolution of any comparable integral field survey to date. The emission-line fitting products include line fluxes, velocities, and velocity dispersions across the WiFeS field of view, and an artificial neural network has been used to determine the optimal number of Gaussian kinematic components for emission-lines in each spaxel. Broad Balmer lines are subtracted from the spectra of nuclear spatial pixels in Seyfert 1 galaxies before fitting the narrow lines. We bin nuclear spectra and measure reddening-corrected nuclear fluxes of strong narrow lines for each galaxy. The nuclear spectra are classified on optical diagnostic diagrams, where the strength of the coronal line [Fe vii] λ 6087 is shown to be correlated with [O iii]/H β . Maps revealing gas excitation and kinematics are included for the entire sample, and we provide notes on the newly observed objects.

An Experimental Evaluation of the Weathering Effects on Mine Shaft Lining Materials

Directory of Open Access Journals (Sweden)

W. Yang

2017-01-01

Full Text Available Many shaft collapses are related to the deterioration and failure of the masonry shaft lining materials. In modern mine shaft, concrete is widely used to provide support. To analyse shafts stability, the properties of the lining need to be well defined. The behaviour of masonry and concrete can be considerably affected by long-term exposure to harsh mine water. This paper presents a study which focuses on the weathering effects of mine water on lining materials (brick, mortar, and concrete. To reproduce the weathering process, samples were placed into solutions of potable water, artificial mine water, and a more aggressive mine-water solution for just less than one year. Four phases of laboratory tests were conducted throughout the time period to assess the degradation of mechanical properties of the lining materials. Particular attention is given to the degradation of material strength and stiffness. Results indicate that the harsh acidic mine water has pronounced detrimental effects on the strength and stiffness of mortar. The weathering process is shown to have the most significant effect on the stiffness of concrete and mortar. It is also shown that the use of mass loss as an index for evaluation of mechanical properties may not be appropriate.

The calculation of oscillator strengths for the 5s21S0→5s5p1,3P1 transitions in Cd-like ions

International Nuclear Information System (INIS)

Li Guangyuan

1998-01-01

The screened hydrogenic model is employed to calculate the oscillator strength of the 5s 2 1 S 0 -5s5p 1 P 1 resonance transition in Cd-like ions (Z = 48 -74). The expression for the oscillator strength of the 5s 2 1 S 0 -5s5p 3 P1 is given, with the introduction of the correctional coefficient K and the mixing angle in jj-coupling. The results are compared with that of other authors, and some discussions are also given

Carrageenan as a dry strength additive for papermaking.

Directory of Open Access Journals (Sweden)

Zhenhua Liu

Full Text Available Carrageenans are commercially important sulfated gums found in various species of red seaweeds (Rhodophyta, wherein they serve a structural function similar to that of pectins in land plants. In this study, carrageenan was used independently or in combination with cationic polyacrylamide (CPAM and/or Al2(SO43 to explore its application as a dry strength additive in papermaking. Strength index determination, ash content detection, FTIR characterization and SEM observation were performed on prepared handsheets. The results showed that with 0.6% Al2(SO43 and 0.2% carrageenan as additives, the tensile index increased by 13.53% and precipitated calcium carbonate (PCC retention increased by 57.06%. With 0.6% Al2(SO43, 0.2% carrageenan and 0.03% CPAM as additives, PCC retention increased by 121% while the tensile index did not fall compared to handsheets without additives, indicating that carrageenan could enhance the strength of handsheets and be used as an anionic dry strength agent.

Soft computing methods for estimating the uniaxial compressive strength of intact rock from index tests

Czech Academy of Sciences Publication Activity Database

Mishra, A. Deepak; Srigyan, M.; Basu, A.; Rokade, P. J.

2015-01-01

Roč. 80, December 2015 (2015), s. 418-424 ISSN 1365-1609 Institutional support: RVO:68145535 Keywords : uniaxial compressive strength * rock indices * fuzzy inference system * artificial neural network * adaptive neuro-fuzzy inference system Subject RIV: DH - Mining, incl. Coal Mining Impact factor: 2.010, year: 2015 http://ac.els-cdn.com/S1365160915300708/1-s2.0-S1365160915300708-main.pdf?_tid=318a7cec-8929-11e5-a3b8-00000aacb35f&acdnat=1447324752_2a9d947b573773f88da353a16f850eac

Roles of pinning strength and density in vortex melting

International Nuclear Information System (INIS)

Obaidat, I M; Khawaja, U Al; Benkraouda, M

2008-01-01

We have investigated the role of pinning strength and density on the equilibrium vortex-lattice to vortex-liquid phase transition under several applied magnetic fields. This study was conducted using a series of molecular dynamic simulations on several samples with different strengths and densities of pinning sites which are arranged in periodic square arrays. We have found a single solid-liquid vortex transition when the vortex filling factor n>1. We have found that, for fixed pinning densities and strengths, the melting temperature, T m , decreases almost linearly with increasing magnetic field. Our results provide direct numerical evidence for the significant role of both the strength and density of pinning centers on the position of the melting line. We have found that the vortex-lattice to vortex-liquid melting line shifts up as the pinning strength or the pinning density was increased. The effect on the melting line was found to be more pronounced at small values of strength and density of pinning sites

Reliability estimate of unconfined compressive strength of black cotton soil stabilized with cement and quarry dust

Directory of Open Access Journals (Sweden)

Dayo Oluwatoyin AKANBI

2017-06-01

Full Text Available Reliability estimates of unconfined compressive strength values from laboratory results for specimens compacted at British Standard Light (BSLfor compacted quarry dust treated black cotton soil using cement for road sub – base material was developed by incorporating data obtained from Unconfined compressive strength (UCS test gotten from the laboratory test to produce a predictive model. Data obtained were incorporated into a FORTRAN-based first-order reliability program to obtain reliability index values. Variable factors such as water content relative to optimum (WRO, hydraulic modulus (HM, quarry dust (QD, cement (C, Tri-Calcium silicate (C3S, Di-calcium silicate (C2S, Tri-Calcium Aluminate (C3A, and maximum dry density (MDD produced acceptable safety index value of1.0and they were achieved at coefficient of variation (COV ranges of 10-100%. Observed trends indicate that WRO, C3S, C2S and MDD are greatly influenced by the COV and therefore must be strictly controlled in QD/C treated black cotton soil for use as sub-base material in road pavements. Stochastically, British Standard light (BSL can be used to model the 7 days unconfined compressive strength of compacted quarry dust/cement treated black cotton soil as a sub-base material for road pavement at all coefficient of variation (COV range 10 – 100% because the safety index obtained are higher than the acceptable 1.0 value.

Relationship Between Selected Strength and Power Assessments to Peak and Average Velocity of the Drive Block in Offensive Line Play.

Science.gov (United States)

Jacobson, Bert H; Conchola, Eric C; Smith, Doug B; Akehi, Kazuma; Glass, Rob G

2016-08-01

Jacobson, BH, Conchola, EC, Smith, DB, Akehi, K, and Glass, RG. Relationship between selected strength and power assessments to peak and average velocity of the drive block in offensive line play. J Strength Cond Res 30(8): 2202-2205, 2016-Typical strength training for football includes the squat and power clean (PC) and routinely measured variables include 1 repetition maximum (1RM) squat and 1RM PC along with the vertical jump (VJ) for power. However, little research exists regarding the association between the strength exercises and velocity of an actual on-the-field performance. The purpose of this study was to investigate the relationship of peak velocity (PV) and average velocity (AV) of the offensive line drive block to 1RM squat, 1RM PC, the VJ, body mass (BM), and body composition. One repetition maximum assessments for the squat and PC were recorded along with VJ height, BM, and percent body fat. These data were correlated with PV and AV while performing the drive block. Peal velocity and AV were assessed using a Tendo Power and Speed Analyzer as the linemen fired, from a 3-point stance into a stationary blocking dummy. Pearson product analysis yielded significant (p ≤ 0.05) correlations between PV and AV and the VJ, the squat, and the PC. A significant inverse association was found for both PV and AV and body fat. These data help to confirm that the typical exercises recommended for American football linemen is positively associated with both PV and AV needed for the drive block effectiveness. It is recommended that these exercises remain the focus of a weight room protocol and that ancillary exercises be built around these exercises. Additionally, efforts to reduce body fat are recommended.

In vitro analysis of shear bond strength and adhesive remnant index comparing light curing and self-curing composites

Directory of Open Access Journals (Sweden)

Murilo Gaby Neves

2013-06-01

Full Text Available OBJECTIVE: To evaluate, in vitro, the shear bond strength of self-curing (ConciseTM - 3M and Alpha Plast - DFL and light-curing composites (TransbondTM XT - 3M and Natural Ortho - DFL used in orthodontics bonding, associated to Morelli metal brackets, with further analysis of adhesive remnant index (ARI and enamel condition in scanning electron microscopy (SEM. METHODS: Forty human premolars, just extracted and stored in physiologic solution 0.9 % were used. Randomly, these samples were divided in four groups: G1 group, the brackets were bonded with ConciseTM - 3M composite; in G2 group, Alpha Plast - DFL composite was used; in G3 group, TransbondTM XT - 3M was used; in G4 group, Natural Ortho - DFL composite was used. These groups were submitted to shear strength tests in universal testing machine, at 0.5 mm per minute speed. RESULTS: Statistical difference between G3 and G4 groups was recorded, as G4 showing higher strength resistance than G3. In the other hand, there were no statistical differences between G1, G2 and G3 and G1, G2 and G4 groups. ARI analysis showed that there was no statistical difference between the groups, and low scores were recorded among then. The scanning electron microscopy (SEM analysis revealed the debonding spots and the enamel surface integrity. CONCLUSIONS: Shear bond strength was satisfactory and similar between the composites, however Natural Ortho - DFL revealed best comparing to TransbondTM XT - 3M.

Optimal welding technology of high strength steel S690QL

Directory of Open Access Journals (Sweden)

Dusan Arsic

2015-02-01

Full Text Available In this paper is presented the detailed procedure for defining the optimal technology for welding the structures made of the high strength steel S690QL. That steel belongs into a group of steels with exceptional mechanical properties. The most prominent properties are the high tensile strength and impact toughness, at room and at elevated temperatures, as well. However, this steel has a negative characteristic - proneness to appearance of cold cracks.  That impedes welding and makes as an imperative to study different aspects of this steel's properties as well as those of eventual filler metal. Selection and defining of the optimal welding technology of this high strength steel is done for the purpose of preserving the favorable mechanical properties once the welded joint is realized; properties of the welded metal and the melting zone, as well as in the heat affected zone, which is the most critical zone of the welded joint.

The SLUGGS survey: globular cluster stellar population trends from weak absorption lines in stacked spectra

Science.gov (United States)

Usher, Christopher; Forbes, Duncan A.; Brodie, Jean P.; Romanowsky, Aaron J.; Strader, Jay; Conroy, Charlie; Foster, Caroline; Pastorello, Nicola; Pota, Vincenzo; Arnold, Jacob A.

2015-01-01

As part of the SAGES Legacy Unifying Globulars and GalaxieS (SLUGGS) survey, we stack 1137 Keck DEIMOS (Deep Imaging Multi-Object Spectrograph) spectra of globular clusters from 10 galaxies to study their stellar populations in detail. The stacked spectra have median signal-to-noise ratios of ˜90 Å-1. Besides the calcium triplet, we study weaker sodium, magnesium, titanium and iron lines as well as the Hα and higher order Paschen hydrogen lines. In general, the stacked spectra are consistent with old ages and a Milky Way-like initial mass function. However, we see different metal line index strengths at fixed colour and magnitude, and differences in the calcium triplet-colour relation from galaxy to galaxy. We interpret this as strong evidence for variations in the globular cluster colour-metallicity relation between galaxies. Two possible explanations for the colour-metallicity relation variations are that the average ages of globular clusters vary from galaxy to galaxy or that the average abundances of light elements (i.e. He, C, N and O) differ between galaxies. Stacking spectra by magnitude, we see that the colours become redder and metal line indices stronger with brighter magnitudes. These trends are consistent with the previously reported `blue tilts' being mass-metallicity relations.

APPLIED MECHANICS REVIEWS, WADEX WORD AND AUTHOR INDEX, VOLUME XVI, 1963,

Science.gov (United States)

Author inDEX ) an IBM 1401 prepared mechanical index, extension of KWIC. WADEX usable for browsing and searching. This second WADEX is based on 8,000 titles of APPLIED MECHANICS REVIEWS (AMR), Vol. 16, 1963, an international critical review magazine. In WADEX, titles printed fully with author names, and as many lines used as necessary (60 characters per line). WADEX entry: word in title (except forbidden word) or author’s name. Alphabetically sequenced entries printed out of context. Words are single words or hypenated word pairs or ’Tagged Words’ (TW).

Índice baseado em RFLPs para seleção de linhagens visando sintéticos de milho RFLP marker index for selection of inbred lines aimed at synthetic maize populations

Directory of Open Access Journals (Sweden)

Glauce Cristina Ricardo Rumin

2001-06-01

Full Text Available Marcadores moleculares têm sido sugeridos como ferramentas úteis em programas de melhoramento de plantas. Assim, este trabalho teve como objetivo propor um índice de seleção de linhagens visando a geração de populações sintéticas de milho, baseado em marcadores moleculares e dados de campo. Para tanto foram utilizados valores fenotípicos e genotípicos, oriundos de experimentos convencionais de campo e através da genotipagem das plantas-mãe das linhagens por marcadores RFLP, respectivamente. O índice foi examinado quanto à sua capacidade de originar sintéticos com alta freqüência de alelos favoráveis, em comparação com os obtidos baseando-se na seleção convencional. Utilizaram-se inicialmente 157 locos marcadores com distância média de 15,30 cM entre eles. Sessenta e oito linhagens S2, provenientes da geração F2 do cruzamento entre duas linhagens homozigóticas foram cruzadas em topcross e avaliadas em quatro locais de Iowa, EUA, em 1996. Dos 157 locos foram selecionados 18 que explicaram 74,70% da variância genética entre progênies, na média dos locais. O índice proposto leva em conta o comportamento próprio (per se das linhagens e a complementaridade genotípica entre elas, o que não é conseguido utilizando-se apenas dados dos topcrosses. O uso do índice proposto permite obter homólogo de tabela dialélica tendo-se apenas dados de médias de topcrosses. O índice levou à seleção de sintéticos com propriedades superiores às esperadas pela seleção baseada apenas nas médias das progênies topcross. Essa conclusão, no entanto, só é válida para os QTL's abrangidos pelas marcas. A metodologia proposta permite monitoramento muito adequado e útil das propriedades genéticas dos sintéticos a serem obtidos.Molecular markers have been suggested as useful tools in breeding programmes. The purpose of this work was to propose and apply an index for inbred line selection to be used for generating synthetic

Starlight excitation of permitted lines in gaseous nebulae

International Nuclear Information System (INIS)

Grandi, S.A.

1975-01-01

The weak heavy element permitted lines observed in the spectra of gaseous nebula have, with only a few exceptions, been thought to be excited only by recombination. The accuracy of this assumption for individual lines in nebula spectra is investigated in detail via model nebula calculations. First, approximations and techniques of calculation are considered for the three possible excitation mechanisms: recombination, resonance fluorescence by the starlight continuum, and resonance fluorescence by other nebular emission lines. Next, the permitted lines of O I as observed in gaseous nebulae are discussed. Thirdly, it is shown that varying combinations of recombination, resonance fluorescence by starlight, and resonance fluorescence by other nebula lines can successfully account for the observed strengths in the Orion Nebula of lines of the following ions: C II, N I, N II, N III, O II, Ne II, Si II, Si III, and S III. A similar analysis is performed for the lines in the spectra of the planetary nebulae NGC7662 and NGC7027, and, with some exceptions, satisfactory agreement between the observed and predicted line strengths is found. Finally, observations of the far red spectra of the Orion Nebula, the planetary nebulae NGC3242, NGC6210, NGC2392, IC3568, IC4997, NGC7027, and MGC7662, and the reflection nebulae IC431 and NGC2068 are reported

Dielectric strength test to protection elements for live lines works

Directory of Open Access Journals (Sweden)

Carlos Eduardo Pinto-Salamanca

2017-06-01

Full Text Available This paper presents the design and assembly of a system of tests of sustained voltage to elements and equipment used in live line maneuvers through tests on gloves and dielectric rods, as these are the first points of contact to ensure safe operations. It means an advance for the creation of a laboratory certified in this type of tests at Universidad Pedagógica y Tecnológica de Colombia (UPTC Faculty of Duitama, considering that currently there are not laboratories that provide this service in Boyacá and Casanare. Dielectric strength tests were performed on personal protection elements and equipment under the parameters of ASTM D120, ASTM F496, ISO 60903, ASTM-F711 and IEEE 978, developing an assembly for testing gloves and dielectric rods with voltage levels up to 15 kV. The results validate the proposed system to outlook of circuit design and implementation, where tests were performed to establish dielectric capacities, in operating under open circuit conditions, with resistive load or short circuit. The compliance with the regulations established under the test sequences of safety parameters for the system and the follow-up to the tests was verified through the use of a management system for the generation of concepts of approval or rejection of the tested elements.

Utility of the RENAL index -Radius; Exophytic/endophytic; Nearness to sinus; Anterior/posterior; Location relative to polar lines- in the management of renal masses.

Science.gov (United States)

Konstantinidis, C; Trilla, E; Lorente, D; Morote, J

2016-12-01

The growing incidence of renal masses and the wide range of available treatments require predictive tools that support the decision making process. The RENAL index -Radius; Exophytic/endophytic; Nearness to sinus; Anterior/posterior; Location relative to polar lines- helps standardise the anatomy of a renal mass by differentiating 3 groups of complexity. Since the introduction of the index, there have been a growing number of studies, some of which have been conflicting, that have evaluated the clinical utility of its implementation. To analyse the scientific evidence on the relationship between the RENAL index and the main strategies for managing renal masses. A search was conducted in the Medline database, which found 576 references on the RENAL index. In keeping with the PRISM Declaration, we selected 100 abstracts and ultimately reviewed 96 articles. The RENAL index has a high degree of interobserver correlation and has been validated as a predictive nomogram of histological results. In active surveillance, the index has been related to the tumour growth rate and probability of nephrectomy. In ablative therapy, the index has been associated with therapeutic efficacy, complications and tumour recurrence. In partial nephrectomy, the index has been related to the rate of complications, conversion to radical surgery, ischaemia time, function preservation and tumour recurrence, a finding also observed in radical nephrectomy. The RENAL index is an objective, reproducible and useful system as a predictive tool of highly relevant clinical parameters such as the rate of complications, ischaemia time, renal function and oncological results in the various currently accepted treatments for the management of renal masses. Copyright © 2016 AEU. Publicado por Elsevier España, S.L.U. All rights reserved.

Properties of Narrow line Seyfert 1 galaxies

Science.gov (United States)

Rakshit, Suvendu; Stalin, Chelliah Subramonian; Chand, Hum; Zhang, Xue-Guang

2018-04-01

Narrow line Seyfert 1 (NLSy1) galaxies constitute a class of active galactic nuclei characterized by the full width at half maximum (FWHM) of the Hα broad emission line 10 pixel-1. A strong correlation between the Hα and Hα emission lines is found both in the FWHM and flux. The nuclear continuum luminosity is found to be strongly correlated with the luminosity of Hα, Hα and [O III] emission lines. The black hole mass in NLSy1 galaxies is lower compared to their broad line counterparts. Compared to BLSy1 galaxies, NLSy1 galaxies have a stronger FeII emission and a higher Eddington ratio that place them in the extreme upper right corner of the R4570 - λEdd diagram. The distribution of the radio-loudness parameter (R) in NLSy1 galaxies drops rapidly at R>10 compared to the BLSy1 galaxies that have powerful radio jets. The soft X-ray photon index in NLSy1 galaxies is on average higher (2.9 ± 0.9) than BLSy1 galaxies (2.4 ± 0.8). It is anti-correlated with the Hα width but correlated with the FeII strength. NLSy1 galaxies on average have a lower amplitude of optical variability compared to their broad lines counterparts. These results suggest Eddington ratio as the main parameter that drives optical variability in these sources.

Two-line hybrid rice male sterile line 'NHR111S' with a marker of green-revertible albino leaves

International Nuclear Information System (INIS)

Wu Wei; Liu Xin; Shu Xiaoli; Shu Qingyao; Xia Yingwu; Wu Dianxing

2006-01-01

NHR111S is a new two-line male sterile line with a marker of green-revertible albino leave that was bred from in vitro mutagens is of the thermo/photoperiod-sensitive male sterile line 'Guangzhan63S' by 60 Co γ-rays. It has the same desired agronomic traits, fertility characteristics and combining ability as characteristics of the parent. It is convenient to develop leaf color marker-aided elimination strategy in the multiplication and production of hybrid rice seeds. (authors)

Hand Grip Strength in Low, Medium, and High Body Mass Index Males and Females

Directory of Open Access Journals (Sweden)

Liao

2016-01-01

Full Text Available Background Hand grip strength (HGS is a predictor of upper extremity function and changes in muscle strength, physical movement and ability to undertake activities of daily living. Body mass index (BMI is a critical indicator of physical health; however, the relationship between HGS and BMI has not yet been thoroughly examined. Objectives The current study aims to compare HGS in low, medium, and high BMI males and females in both hands, and also investigates the correlation between HGS and anthropometric characteristics among the three BMI groups. Patients and Methods The study included 200 participants who were divided into three groups based on their BMI (60 low, 58 medium, and 82 high. HGS was assessed using a hand-held Jamar dynamometer. BMI was assessed by an electric body-weight height analysis machine. Data was analyzed using descriptive and inferential statistics at P 0.05. Weight and height strongly correlated with HGS for hands (correlation (r ranged from 0.000 - 0.775. Regression analysis showed that when using sex and BMI as independent variables for predicting the dependent variable HGS, the coefficient of the determinant R2 was 0.753 (P < 0.001. Conclusions The current study revealed that a significant difference existed in HGS among the low, medium, and high BMI groups. A positive correlation existed between HGS and weight and height, while sex was the most significant factor affecting HGS. These findings can serve as a reference to assess HGS prediction, whereby the sex effect should be considered.

Generalized oscillator strengths for 5s, 5s', and 5p excitations of krypton

International Nuclear Information System (INIS)

Li Wenbin; Zhu Linfan; Yuan Zhensheng; Sun Jianmin; Cheng Huadong; Xu Kezun; Zhong Zhiping; Liu Xiaojing

2003-01-01

The absolute generalized oscillator strengths (GOSs) for 5s, 5s ' , 5p [5/2] 3,2 , 5p [3/2] 1,2 , and 5p [1/2] 0 transitions of krypton have been determined in a large K 2 region at a high electron-impact energy of 2500 eV. The positions of the minima and maxima of these GOSs have been determined. The present results show that the angular resolution and pressure effect have great influence on the position and the amplitude of the minimum for the GOS of 5s+5s ' transitions. When these effects are considered, the measured minimum position for the GOS of 5s+5s ' transitions is in excellent agreement with the calculation of Chen and Msezane [J. Phys. B 33, 5397 (2000)

The added value of measuring thumb and finger strength when comparing strength measurements in hypoplastic thumb patients.

Science.gov (United States)

Molenaar, H M Ties; Selles, Ruud W; de Kraker, Marjolein; Stam, Henk J; Hovius, Steven E R

2013-10-01

When interventions to the hand are aimed at improving function of specific fingers or the thumb, the RIHM (Rotterdam Intrinsic Hand Myometer) is a validated tool and offers more detailed information to assess strength of the involved joints besides grip and pinch measurements. In this study, strength was measured in 65 thumbs in 40 patients diagnosed with thumb hypoplasia. These 65 thumbs were classified according to Blauth. Longitudinal radial deficiencies were also classified. The strength measurements comprised of grip, tip, tripod and key pinch. Furthermore palmar abduction and opposition of the thumb as well as abduction of the index and little finger were measured with the RIHM. For all longitudinal radial deficiency patients, grip and pinch strength as well as palmar abduction and thumb opposition were significantly lower than reference values (P<0.001). However, strength in the index finger abduction and the little finger abduction was maintained or decreased to a lesser extent according to the degree of longitudinal radial deficiency. All strength values decreased with increasing Blauth-type. Blauth-type II hands (n=15) with flexor digitorum superficialis 4 opposition transfer including stabilization of the metacarpophalangeal joint showed a trend toward a higher opposition strength without reaching statistical significance (P=0.094),however compared to non-operated Blauth-type II hands (n=6) they showed a lower grip strength (P=0.019). The RIHM is comparable in accuracy to other strength dynamometers. Using the RIHM, we were able to illustrate strength patterns on finger-specific level, showing added value when evaluating outcome in patients with hand related problems. © 2013.

Precision measurement of relative oscillator strengths

International Nuclear Information System (INIS)

Blackwell, D.E.; Ibbetson, P.A.; Petford, A.D.; Shallis, M.J.

1979-01-01

The accuracy of the Oxford method of comparing oscillator strengths has been improved by a factor of 10 to 0.5 per cent (0.002 dex) for low excitation lines. The improvements made to the apparatus are briefly described and its new performance discussed. A test for LTE in the furnace is also described. Relative oscillator strengths for 60 lines of Fe I with excitation potentials between 0.00 and 0.12 eV are given. Those with lambda > 320 nm have an accuracy of 0.5 per cent, and those with lambda < 320 nm have an accuracy of 1.0 per cent. Absolute values with an accuracy of 2.5 per cent for all lines are given. (author)

Application of Dexter’s soil physical quality index: an Irish case study

Directory of Open Access Journals (Sweden)

Fenton O.

2017-08-01

Full Text Available Historically, due to a lack of measured soil physical data, the quality of Irish soils was relatively unknown. Herein, we investigate the physical quality of the national representative profiles of Co. Waterford. To do this, the soil physical quality (SPQ S-Index, as described by Dexter (2004a,b,c using the S-theory (which seeks the inflection point of a soil water retention curve [SWRC], is used. This can be determined using simple (S-Indirect or complex (S-Direct soil physical data streams. Both are achievable using existing data for the County Waterford profiles, but until now, the suitability of this S-Index for Irish soils has never been tested. Indirect-S provides a generic characterisation of SPQ for a particular soil horizon, using simplified and modelled information (e.g. texture and SWRC derived from pedo-transfer functions, whereas Direct-S provides more complex site-specific information (e.g. texture and SWRC measured in the laboratory, which relates to properties measured for that exact soil horizon. Results showed a significant correlation between S-Indirect (Si and S-Direct (Sd. Therefore, the S-Index can be used in Irish soils and presents opportunities for the use of Si at the national scale. Outlier horizons contained >6% organic carbon (OC and bulk density (Bd values <1 g/cm3 and were not suitable for Si estimation. In addition, the S-Index did not perform well on excessively drained soils. Overall correlations of Si. with Bd and of Si. with OC% for the dataset were detected. Future work should extend this approach to the national scale dataset in the Irish Soil Information System.

Cerebral state index during propofol anesthesia : A Comparison with the Bispectral Index and the A-Line ARX Index

NARCIS (Netherlands)

Jensen, EW; Litvan, H; Revuelta, M; Rodriguez, BE; Caminal, P; Martinez, P; Vereecke, H; Struys, Michel MRF

Background: The objective of this study was to prospectively test the Cerebral State Index designed for measuring the depth of anesthesia. The Cerebral State Index is calculated using a fuzzy logic combination of four subparameters of the electroencephalographic signal. The performance of the

(p,γ) resonance strengths in the s-d shell

International Nuclear Information System (INIS)

Paine, B.M.; Sargood, D.G.

1979-01-01

The strengths of selected resonances in the energy range 0.5-2.0 MeV in the (p,γ) reactions on 26 Mg, 30 Si, 34 S, 37 C1, 39 K and 40 Ca have been found relative to the 632 and 992 keV resonances in 27 A1(p,γ) 28 Si by relative yield measurements. Absolute measurements were conducted on the selected resonances in 27 A1(p,γ) 28 Si and 30 Si(p,γ) 31 p by semi-thick target and thin target techniques with the target thickness, needed for the latter technique, found by Rutherford backscattering of protons. Absolute strengths for all of the resonances treated, together with one from each of 23 Na, 31 p and 35 C1, reported in a previous paper, were deduced by normalizing to the absolute measurements on the 27 A1(p,γ) 28 Si resonances

Performance Analysis of Indonesia’s Mining Sector Price Index

Directory of Open Access Journals (Sweden)

Hastra Reza Satyatama

2017-07-01

Full Text Available Subprime mortage’s crisis in United States 2008 giving effect to the global capital markets especially the stock price index of the mining sector Indonesia. This research analyzes the effect of BI Rate, exchange rate, world gold price, crude oil price, and Dow Jones Industrial Average on the stock price index of the mining sector. This research employs time series monthly data of 2009-2016 with Error Correction Model-Engle Granger (ECM-EG as the method. The analysis showed that the BI rate, exchange rate and world gold price, has a negative and significant effect. World oil prices affect positively but not significant meanwhile the Dow Jones Industrial Average has a positive and significant impact on the stock price index of the mining sector. For investors in the mining sector, should pay attention to the exchange rate of the rupiah and Dow Jones Index significantly in the mining sector of the stock price index.DOI: 10.15408/sjie.v6i2.5395 

Adding the s-Process Element Cerium to the APOGEE Survey: Identification and Characterization of Ce II Lines in the H-band Spectral Window

Science.gov (United States)

Cunha, Katia; Smith, Verne V.; Hasselquist, Sten; Souto, Diogo; Shetrone, Matthew D.; Allende Prieto, Carlos; Bizyaev, Dmitry; Frinchaboy, Peter; García-Hernández, D. Anibal; Holtzman, Jon; Johnson, Jennifer A.; Jőnsson, Henrik; Majewski, Steven R.; Mészáros, Szabolcs; Nidever, David; Pinsonneault, Mark; Schiavon, Ricardo P.; Sobeck, Jennifer; Skrutskie, Michael F.; Zamora, Olga; Zasowski, Gail; Fernández-Trincado, J. G.

2017-08-01

Nine Ce II lines have been identified and characterized within the spectral window observed by the Apache Point Observatory Galactic Evolution Experiment (APOGEE) survey (between λ1.51 and 1.69 μm). At solar metallicities, cerium is an element that is produced predominantly as a result of the slow capture of neutrons (the s-process) during asymptotic giant branch stellar evolution. The Ce II lines were identified using a combination of a high-resolution (R=λ /δ λ ={{100,000}}) Fourier Transform Spectrometer (FTS) spectrum of α Boo and an APOGEE spectrum (R = 22,400) of a metal-poor, but s-process enriched, red giant (2M16011638-1201525). Laboratory oscillator strengths are not available for these lines. Astrophysical gf-values were derived using α Boo as a standard star, with the absolute cerium abundance in α Boo set by using optical Ce II lines that have precise published laboratory gf-values. The near-infrared Ce II lines identified here are also analyzed, as consistency checks, in a small number of bright red giants using archival FTS spectra, as well as a small sample of APOGEE red giants, including two members of the open cluster NGC 6819, two field stars, and seven metal-poor N- and Al-rich stars. The conclusion is that this set of Ce II lines can be detected and analyzed in a large fraction of the APOGEE red giant sample and will be useful for probing chemical evolution of the s-process products in various populations of the Milky Way.

Temperature and orientation dependence of the short-term strength characteristics, Young's modulus, and linear expansion coefficient of ZhS6F alloy single crystals

Energy Technology Data Exchange (ETDEWEB)

Svetlov, I L; Sukhanov, N N; Krivko, A I; Roshchina, I N; Khatsinskaia, I M

1987-01-01

Experimental data are presented on the temperature dependence of the short- term strength characteristics, Young's modulus, and linear expansion coefficients of single crystals of a nickel alloy, ZhS6F, with crystallographic orientations along the 001, 111, 011, and 112 lines. It is found that the mechanical properties and Young's modulus of the alloy crystals exibit anisotropy in the temperature range 20-900 C. The linear thermal expansion coefficient is isotropic up to 900 C and equal to that of the equiaxed alloy. 10 references.

Relvakogujad sõjaajalooklubist Front Line vahistati / Kadri Ratt

Index Scriptorium Estoniae

Ratt, Kadri

2009-01-01

Kaitsepolitsei võttis vahi alla 9 meest, keda kahtlustatakse suures koguses lõhkeainete, lõhkekehade ja tulirelvade ebaseaduslikus käitlemises. 6 meest neist kuuluvad sõjaajalooklubisse Front Line

The Kirchhoff Index of Some Combinatorial Networks

Directory of Open Access Journals (Sweden)

Jia-Bao Liu

2015-01-01

Full Text Available The Kirchhoff index Kf(G is the sum of the effective resistance distances between all pairs of vertices in G. The hypercube Qn and the folded hypercube FQn are well known networks due to their perfect properties. The graph G∗, constructed from G, is the line graph of the subdivision graph S(G. In this paper, explicit formulae expressing the Kirchhoff index of (Qn∗ and (FQn∗ are found by deducing the characteristic polynomial of the Laplacian matrix of G∗ in terms of that of G.

Diagnostic ability of Barrett's index to detect dysthyroid optic neuropathy using multidetector computed tomography

Energy Technology Data Exchange (ETDEWEB)

Monteiro, Mario L.R.; Goncalves, Allan C.P.; Silva, Carla T.M.; Moura, Janete P.; Ribeiro, Carolina S.; Gebrim, Eloisa M.M.S. [Universidade de Sao Paulo (USP), SP (Brazil). Hospital das Clinicas. Division of Ophthalmology; Universidade de Sao Paulo (USP), SP (Brazil). Hospital das Clinicas. Dept. of Endocrinology; Universidade de Sao Paulo (USP), SP (Brazil). Hospital das Clinicas. Division of Radiology]. E-mail: mlrmonteiro@terra.com.br

2008-07-01

Objectives: The objective of this study was to evaluate the ability of a muscular index (Barrett's Index), calculated with multidetector computed tomography, to detect dysthyroid optic neuropathy in patients with Graves' orbitopathy. Methods: Thirty-six patients with Graves' orbitopathy were prospectively studied and submitted to neuro-ophthalmic evaluation and multidetector computed tomography scans of the orbits. Orbits were divided into two groups: those with and without dysthyroid optic neuropathy. Barrett's index was calculated as the percentage of the orbit occupied by muscles. Sensitivity and specificity were determined for several index values. Results: Sixty-four orbits (19 with and 45 without dysthyroid optic neuropathy) met the inclusion criteria for the study. The mean Barrett's index values ({+-}SD) were 64.47% {+-} 6.06% and 49.44% {+-} 10.94% in the groups with and without dysthyroid optic neuropathy, respectively (p<0.001). Barrett's index sensitivity ranged from 32% to 100%, and Barrett's index specificity ranged from 24% to 100%. The best combination of sensitivity and specificity was 79%/72% for BI=60% (odds ratio: 9.2). Conclusions: Barrett's Index is a useful indicator of dysthyroid optic neuropathy and may contribute to early diagnosis and treatment. Patients with a Barrett's index >60% should be carefully examined and followed for the development of dysthyroid optic neuropathy. (author)

The validity and reliability of the my jump 2 app for measuring the reactive strength index and drop jump performance.

Science.gov (United States)

Haynes, Tom; Bishop, Chris; Antrobus, Mark; Brazier, Jon

2018-03-27

This is the first study to independently assess the concurrent validity and reliability of the My Jump 2 app for measuring drop jump performance. It is also the first to evaluate the app's ability to measure the reactive strength index (RSI). Fourteen male sport science students (age: 29.5 ± 9.9 years) performed three drop jumps from 20 cm and 40 cm (totalling 84 jumps), assessed via a force platform and the My Jump 2 app. Reported metrics included reactive strength index, jump height, ground contact time, and mean power. Measurements from both devices were compared using the intraclass correlation coefficient (ICC), Pearson product moment correlation coefficient (r), Cronbach's alpha (α), coefficient of variation (CV) and BlandAltman plots. Near perfect agreement was seen between devices at 20 cm for RSI (ICC = 0.95) and contact time (ICC = 0.99) and at 40 cm for RSI (ICC = 0.98), jump height (ICC = 0.96) and contact time (ICC = 0.92); with very strong agreement seen at 20 cm for jump height (ICC = 0.80). In comparison with the force plate the app showed good validity for RSI (20 cm: r = 0.94; 40 cm; r = 0.97), jump height (20 cm: r = 0.80; 40 cm; r = 0.96) and contact time (20 cm = 0.96; 40 cm; r = 0.98). The results of the present study show that the My Jump 2 app is a valid and reliable tool for assessing drop jump performance.

Ultrasonic Waves and Strength Reduction Indexes for the Assessment of the Advancement of Deterioration Processes in Travertines from Pamukkale and Hierapolis (Turkey

Directory of Open Access Journals (Sweden)

Bobrowska Alicja

2015-09-01

Full Text Available In constructions, the usefulness of modern technical diagnostics of stone as a raw material requires predicting the effects of long-term environmental impact of its qualities and geomechanical properties. The paper presents geomechanical research enabling presentation of the factors for strength loss of the stone and forecasting the rate of development of destructive phenomena on the stone structure on a long-time basis. As research material Turkish travertines were selected from the Denizli-Kaklık Basin (Pamukkale and Hierapolis quarries, which have been commonly used for centuries in global architecture. The rock material was subjected to testing of the impact of various environmental factors, as well as European standards recommended by the author of the research program. Their resistance to the crystallization of salts from aqueous solutions and the effects of SO2, as well as the effect of frost and high temperatures are presented. The studies allowed establishing the following quantitative indicators: the ultrasonic waves index (IVp and the strength reduction index (IRc. Reflections on the assessment of deterioration effects indicate that the most active factors decreasing travertine resistance in the aging process include frost and sulphur dioxide (SO2. Their negative influence is particularly intense when the stone material is already strongly weathered.

The geomechanical strength of carbonate rock in Kinta valley, Ipoh, Perak Malaysia

Science.gov (United States)

Mazlan, Nur Amanina; Lai, Goh Thian; Razib, Ainul Mardhiyah Mohd; Rafek, Abdul Ghani; Serasa, Ailie Sofyiana; Simon, Norbert; Surip, Noraini; Ern, Lee Khai; Mohamed, Tuan Rusli

2018-04-01

The stability of both cut rocks and underground openings were influenced by the geomechanical strength of rock materials, while the strength characteristics are influenced by both material characteristics and the condition of weathering. This paper present a systematic approach to quantify the rock material strength characteristics for material failure and material & discontinuities failure by using uniaxial compressive strength, point load strength index and Brazilian tensile strength for carbonate rocks. Statistical analysis of the results at 95 percent confidence level showed that the mean value of compressive strength, point load strength index and Brazilian tensile strength for with material failure and material & discontinuities failure were 76.8 ± 4.5 and 41.2 ± 4.1 MPa with standard deviation of 15.2 and 6.5 MPa, respectively. The point load strength index for material failure and material & discontinuities failure were 3.1 ± 0.2 MPa and 1.8 ± 0.3 MPa with standard deviation of 0.9 and 0.6 MPa, respectively. The Brazilian tensile strength with material failure and material & discontinuities failure were 7.1 ± 0.3 MPa and 4.1 ± 0.3 MPa with standard deviation of 1.4 and 0.6 MPa, respectively. The results of this research revealed that the geomechanical strengths of rock material of carbonate rocks for material & discontinuities failure deteriorates approximately ½ from material failure.

Tools for Building on Youth Strengths

Science.gov (United States)

Cox, Kathy

2008-01-01

While rhetoric about strength-based approaches abounds, this perspective has not penetrated the front lines of practice. Many programs serving troubled youngsters are still mired in a deficit and deviance orientation. This article provides practical strategies for assessing the strengths of children and developing interventions to tap their assets…

Cyclotron Lines: From Magnetic Field Strength Estimators to ...

Indian Academy of Sciences (India)

Chandreyee Maitra

2017-09-12

Sep 12, 2017 ... context can provide, to build a complete picture for the physics of accretion and ... cesses which occur near the NS surface, where the ... CRSF) which is the focal point of discussion in this arti- .... first direct measurement of the magnetic field strength of .... The above model requires a gradient in the magnetic.

Development of the index to evaluate the level of educational success performed in line with curriculum policy

OpenAIRE

浜崎, 央; 片庭, 美咲; 柴田, 幸一; 住吉, 廣行

2014-01-01

We aim to propose an index to evaluate the level of educational success performed in line with curriculum policy．We will point out that there exist two conditions for checking the improvement of the educational performance by teachers at universities. Enhancing various teaching skills by "student evaluation" and/or "classroom observation" can be regarded as a "necessary condition" but not "sufficient condition". Therefore, we propose the "sufficient condition" to obtain satisfactory education...

Starck Ta PTW strength model recommendation for use with SESAME 93524 EoS

Energy Technology Data Exchange (ETDEWEB)

Sjue, Sky K. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Prime, Michael Bruce [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-02-27

The purpose of this document is to provide a calibration of the Preston-Tonks- Wallace (PTW) strength model for use with the new SESAME equation of state (EoS) 93524. The calibration data included in this t spans temperatures from 198 K to 673 K and strain rates from 0.001/s to 3200/s.

Research progress of on-line automatic monitoring of chemical oxygen demand (COD) of water

Science.gov (United States)

Cai, Youfa; Fu, Xing; Gao, Xiaolu; Li, Lianyin

2018-02-01

With the increasingly stricter control of pollutant emission in China, the on-line automatic monitoring of water quality is particularly urgent. The chemical oxygen demand (COD) is a comprehensive index to measure the contamination caused by organic matters, and thus it is taken as one important index of energy-saving and emission reduction in China’s “Twelve-Five” program. So far, the COD on-line automatic monitoring instrument has played an important role in the field of sewage monitoring. This paper reviews the existing methods to achieve on-line automatic monitoring of COD, and on the basis, points out the future trend of the COD on-line automatic monitoring instruments.

The strength compass

DEFF Research Database (Denmark)

Ledertoug, Mette Marie

of agreement/disagreement. Also the child/teacher is asked whether the actual strength is important and if he or she has the possibilities to apply the strength in the school. In a PhDproject ‘Strengths-based Learning - Children’s Character Strengths as Means to their Learning Potential’ 750 Danish children......Individual paper presentation: The ‘Strength Compass’. The results of a PhDresearch project among schoolchildren (age 6-16) identifying VIAstrengths concerning age, gender, mother-tongue-langue and possible child psychiatric diagnosis. Strengths-based interventions in schools have a theoretical...... Psychological Publishing Company. ‘The Strength Compass’ is a computer/Ipad based qualitative tool to identify the strengths of a child by a self-survey or a teacher’s survey. It is designed as a visual analogue scale with a statement of the strength in which the child/teacher may declare the degree...

Relation between body mass index percentile and muscle strength ...

African Journals Online (AJOL)

Noha Abdel Kader Abdel Kader Hasan

2016-02-01

Feb 1, 2016 ... Abstract Background: Muscle strength and endurance in children are very important to develop physical .... the Faculty of Physical Therapy, Cairo university, was used to ..... [9] Noelle G. Quantification of muscle fatigue in cerebral palsy and ... Bouckaert J. Physical fitness and physical activity in obese and.

Physiological Evaluation of Alkali-Salt Tolerance of Thirty Switchgrass (Panicum virgatum Lines.

Directory of Open Access Journals (Sweden)

Guofu Hu

Full Text Available Soil salt-alkalization is a major limiting factor for crop production in many regions. Switchgrass (Panicum virgatum L. is a warm-season C4 perennial rhizomatous bunchgrass and a target lignocellulosic biofuel species. The objective of this study was to evaluate relative alkali-salt tolerance among 30 switchgrass lines. Tillers of each switchgrass line were transplanted into pots filled with fine sand. Two months after transplanting, plants at E5 developmental stage were grown in either half strength Hoagland's nutrient solution with 0 mM Na+ (control or half strength Hoagland's nutrient solution with 150 mM Na+ and pH of 9.5 (alkali-salt stress treatment for 20 d. Alkali-salt stress damaged cell membranes [higher electrolyte leakage (EL], reduced leaf relative water content (RWC, net photosynthetic rate (Pn, stomatal conductance (gs, and transpiration rate (Tr. An alkali-salt stress tolerance trait index (ASTTI for each parameter was calculated based on the ratio of the value under alkali-salt stress and the value under non-stress conditions for each parameter of each line. Relative alkali-salt tolerance was determined based on principal components analysis and cluster analysis of the physiological parameters and their ASTTI values. Significant differences in alkali-salt stress tolerance were found among the 30 lines. Lowland lines TEM-SEC, Alamo, TEM-SLC and Kanlow were classified as alkali-salt tolerant. In contrast, three lowland lines (AM-314/MS-155, BN-13645-64 and two upland lines (Caddo and Blackwell-1 were classified as alkali-salt sensitive. The results suggest wide variations exist in alkali-salt stress tolerance among the 30 switchgrass lines. The approach of using a combination of principal components and cluster analysis of the physiological parameters and related ASTTI is feasible for evaluating alkali-salt tolerance in switchgrass.

Physiological Evaluation of Alkali-Salt Tolerance of Thirty Switchgrass (Panicum virgatum) Lines.

Science.gov (United States)

Hu, Guofu; Liu, Yiming; Zhang, Xunzhong; Yao, Fengjiao; Huang, Yan; Ervin, Erik H; Zhao, Bingyu

2015-01-01

Soil salt-alkalization is a major limiting factor for crop production in many regions. Switchgrass (Panicum virgatum L.) is a warm-season C4 perennial rhizomatous bunchgrass and a target lignocellulosic biofuel species. The objective of this study was to evaluate relative alkali-salt tolerance among 30 switchgrass lines. Tillers of each switchgrass line were transplanted into pots filled with fine sand. Two months after transplanting, plants at E5 developmental stage were grown in either half strength Hoagland's nutrient solution with 0 mM Na+ (control) or half strength Hoagland's nutrient solution with 150 mM Na+ and pH of 9.5 (alkali-salt stress treatment) for 20 d. Alkali-salt stress damaged cell membranes [higher electrolyte leakage (EL)], reduced leaf relative water content (RWC), net photosynthetic rate (Pn), stomatal conductance (gs), and transpiration rate (Tr). An alkali-salt stress tolerance trait index (ASTTI) for each parameter was calculated based on the ratio of the value under alkali-salt stress and the value under non-stress conditions for each parameter of each line. Relative alkali-salt tolerance was determined based on principal components analysis and cluster analysis of the physiological parameters and their ASTTI values. Significant differences in alkali-salt stress tolerance were found among the 30 lines. Lowland lines TEM-SEC, Alamo, TEM-SLC and Kanlow were classified as alkali-salt tolerant. In contrast, three lowland lines (AM-314/MS-155, BN-13645-64) and two upland lines (Caddo and Blackwell-1) were classified as alkali-salt sensitive. The results suggest wide variations exist in alkali-salt stress tolerance among the 30 switchgrass lines. The approach of using a combination of principal components and cluster analysis of the physiological parameters and related ASTTI is feasible for evaluating alkali-salt tolerance in switchgrass.

A CLOUDINESS INDEX FOR TRANSITING EXOPLANETS BASED ON THE SODIUM AND POTASSIUM LINES: TENTATIVE EVIDENCE FOR HOTTER ATMOSPHERES BEING LESS CLOUDY AT VISIBLE WAVELENGTHS

Energy Technology Data Exchange (ETDEWEB)

Heng, Kevin, E-mail: kevin.heng@csh.unibe.ch [University of Bern, Center for Space and Habitability, Sidlerstrasse 5, CH-3012, Bern (Switzerland)

2016-07-20

We present a dimensionless index that quantifies the degree of cloudiness of the atmosphere of a transiting exoplanet. Our cloudiness index is based on measuring the transit radii associated with the line center and wing of the sodium or potassium line. In deriving this index, we revisited the algebraic formulae for inferring the isothermal pressure scale height from transit measurements. We demonstrate that the formulae of Lecavelier et al. and Benneke and Seager are identical: the former is inferring the temperature while assuming a value for the mean molecular mass and the latter is inferring the mean molecular mass while assuming a value for the temperature. More importantly, these formulae cannot be used to distinguish between cloudy and cloud-free atmospheres. We derive values of our cloudiness index for a small sample of seven hot Saturns/Jupiters taken from Sing et al. We show that WASP-17b, WASP-31b, and HAT-P-1b are nearly cloud-free at visible wavelengths. We find the tentative trend that more irradiated atmospheres tend to have fewer clouds consisting of sub-micron-sized particles. We also derive absolute sodium and/or potassium abundances ∼10{sup 2} cm{sup −3} for WASP-17b, WASP-31b, and HAT-P-1b (and upper limits for the other objects). Higher-resolution measurements of both the sodium and potassium lines, for a larger sample of exoplanetary atmospheres, are needed to confirm or refute this trend.

Lifetime measurements and oscillator strengths in singly ionized scandium and the solar abundance of scandium

Science.gov (United States)

Pehlivan Rhodin, A.; Belmonte, M. T.; Engström, L.; Lundberg, H.; Nilsson, H.; Hartman, H.; Pickering, J. C.; Clear, C.; Quinet, P.; Fivet, V.; Palmeri, P.

2017-12-01

The lifetimes of 17 even-parity levels (3d5s, 3d4d, 3d6s and 4p2) in the region 57 743-77 837 cm-1 of singly ionized scandium (Sc II) were measured by two-step time-resolved laser induced fluorescence spectroscopy. Oscillator strengths of 57 lines from these highly excited upper levels were derived using a hollow cathode discharge lamp and a Fourier transform spectrometer. In addition, Hartree-Fock calculations where both the main relativistic and core-polarization effects were taken into account were carried out for both low- and high-excitation levels. There is a good agreement for most of the lines between our calculated branching fractions and the measurements of Lawler & Dakin in the region 9000-45 000 cm-1 for low excitation levels and with our measurements for high excitation levels in the region 23 500-63 100 cm-1. This, in turn, allowed us to combine the calculated branching fractions with the available experimental lifetimes to determine semi-empirical oscillator strengths for a set of 380 E1 transitions in Sc II. These oscillator strengths include the weak lines that were used previously to derive the solar abundance of scandium. The solar abundance of scandium is now estimated to logε⊙ = 3.04 ± 0.13 using these semi-empirical oscillator strengths to shift the values determined by Scott et al. The new estimated abundance value is in agreement with the meteoritic value (logεmet = 3.05 ± 0.02) of Lodders, Palme & Gail.

A Novel Line Coding Pair for Fully Passive Long Reach {WDM-PON}s

DEFF Research Database (Denmark)

Presi, Marco; Proietti, Roberto; Prince, Kamau

2008-01-01

A novel line coding pair allows to use unsaturated flective-SOAs as upstream remodulator in long-reach WDM-PONs. Full-duplex and symmetric 80 km reach is demonstrated without in-line amplification at 1.25 Gb/s......A novel line coding pair allows to use unsaturated flective-SOAs as upstream remodulator in long-reach WDM-PONs. Full-duplex and symmetric 80 km reach is demonstrated without in-line amplification at 1.25 Gb/s...

Effects of substorms on the stormtime ring current index Dst

Directory of Open Access Journals (Sweden)

G. Rostoker

Full Text Available There has been some discussion in recent times regarding whether or not substorm expansive phase activity plays any role of importance in the formation of the stormtime ring current. I explore this question using the Kp index as a proxy for substorm expansive phase activity and the Dst index as a proxy for symmetric ring current strength. I find that increases in Dst are mildly related to the strength of substorm expansive phase activity during the development of the storm main phase. More surprisingly, I find that the strength of Dst during the storm recovery phase is positively correlated with the strength of substorm expansive phase activity. This result has an important bearing on the question of how much the Dst index reflects activity other than that of the stormtime symmetric ring current strength for which it is supposed to be a proxy.Key words: Ionosphere (electric fields and currents - Magnetospheric physics (current systems; storms and substorms

Effects of substorms on the stormtime ring current index Dst

Directory of Open Access Journals (Sweden)

G. Rostoker

2000-11-01

Full Text Available There has been some discussion in recent times regarding whether or not substorm expansive phase activity plays any role of importance in the formation of the stormtime ring current. I explore this question using the Kp index as a proxy for substorm expansive phase activity and the Dst index as a proxy for symmetric ring current strength. I find that increases in Dst are mildly related to the strength of substorm expansive phase activity during the development of the storm main phase. More surprisingly, I find that the strength of Dst during the storm recovery phase is positively correlated with the strength of substorm expansive phase activity. This result has an important bearing on the question of how much the Dst index reflects activity other than that of the stormtime symmetric ring current strength for which it is supposed to be a proxy.Key words: Ionosphere (electric fields and currents - Magnetospheric physics (current systems; storms and substorms

Constructing Poverty Lines in Croatia Using Kakwani’s Model

Directory of Open Access Journals (Sweden)

Marinko Škare

2017-06-01

Full Text Available This paper presents a new model for defining the poverty line as a possible candidate for the construction of a new official poverty line in Croatia. The model, based on Kakwani’s (2010 approach (nutrition-based anchor, uses consumer theory as the basis for defining food and non-food poverty lines. In Croatia, various alternative poverty indicators have been developed to define the official poverty line. To ensure international comparability and consistency, the poverty threshold expressed in local currency by applying the exchange rate of currencies’ purchasing power (PPP is expressed in international dollars. It is important to ensure implementation of redistributive policies, maximization of market efficiency, and increased social justice. All this policy goals and instruments heavily depend on efficient and precise poverty measurement methods.

On the calculation of line strengths, oscillator strengths and lifetimes for very large principal quantum numbers in hydrogenic atoms and ions by the McLean–Watson formula

International Nuclear Information System (INIS)

Hey, J D

2014-01-01

As a sequel to an earlier study (Hey 2009 J. Phys. B: At. Mol. Opt. Phys. 42 125701), we consider further the application of the line strength formula derived by Watson (2006 J. Phys. B: At. Mol. Opt. Phys. 39 L291) to transitions arising from states of very high principal quantum number in hydrogenic atoms and ions (Rydberg–Rydberg transitions, n > 1000). It is shown how apparent difficulties associated with the use of recurrence relations, derived (Hey 2006 J. Phys. B: At. Mol. Opt. Phys. 39 2641) by the ladder operator technique of Infeld and Hull (1951 Rev. Mod. Phys. 23 21), may be eliminated by a very simple numerical device, whereby this method may readily be applied up to n ≈ 10 000. Beyond this range, programming of the method may entail greater care and complexity. The use of the numerically efficient McLean–Watson formula for such cases is again illustrated by the determination of radiative lifetimes and comparison of present results with those from an asymptotic formula. The question of the influence on the results of the omission or inclusion of fine structure is considered by comparison with calculations based on the standard Condon–Shortley line strength formula. Interest in this work on the radial matrix elements for large n and n′ is related to measurements of radio recombination lines from tenuous space plasmas, e.g. Stepkin et al (2007 Mon. Not. R. Astron. Soc. 374 852), Bell et al (2011 Astrophys. Space Sci. 333 377), to the calculation of electron impact broadening parameters for such spectra (Watson 2006 J. Phys. B: At. Mol. Opt. Phys. 39 1889) and comparison with other theoretical methods (Peach 2014 Adv. Space Res. in press), to the modelling of physical processes in H II regions (Roshi et al 2012 Astrophys. J. 749 49), and the evaluation bound–bound transitions from states of high n during primordial cosmological recombination (Grin and Hirata 2010 Phys. Rev. D 81 083005, Ali-Haïmoud and Hirata 2010 Phys. Rev. D 82 063521

Normalized knee-extension strength or leg-press power after fast-track total knee arthroplasty

DEFF Research Database (Denmark)

Aalund, Peter K; Larsen, Kristian; Hansen, Torben Bæk

2013-01-01

OBJECTIVE: (s): To investigate which of the two muscle-impairment measures for the operated leg, normalized knee extension strength or leg press power, is more closely associated to performance-based and self-reported measures of function shortly following total knee arthroplasty (TKA). DESIGN...... and dynamic leg presses to determine their body-mass normalized knee extension strength and leg press power, respectively. The 10-m fast speed walking and 30-s chair stand tests were used to determine performance-based function, while the Western Ontario McMaster University Osteoarthritis Index (WOMAC......) and Oxford Knee scores were used to determine self-reported function. RESULTS: Normalized leg press power was more closely associated to both performance-based (r=.82, P...

Muscular strength and endurance and cardio-metabolic health in disadvantaged Hispanic children from the U.S.

Directory of Open Access Journals (Sweden)

Ryan D. Burns

2017-03-01

Full Text Available The predictive relationship between muscular strength and endurance and cardio-metabolic health, independent from aerobic fitness, is not clear in disadvantaged Hispanic children. The purpose of this study was to examine the predictive relationship between muscular strength and endurance and clustered cardio-metabolic risk, controlling for aerobic fitness, in Hispanic children from low-income schools. Participants were 320 Hispanic children (Mean age = 10.1 ± 1.1 years; 164 girls, 156 boys recruited during the 2014–2015 and 2015–2016 academic years from five low-income schools from the state of Utah in the U.S. Muscular strength and endurance was assessed using the push-up and curl-up tests and estimated VO2 Peak was calculated from the Progressive Aerobic Cardiovascular Endurance Run. A clustered metabolic syndrome composite score (MetS was calculated from cardio-metabolic health measurements consisting of HDL cholesterol, triglycerides, waist circumference, blood glucose, and mean arterial pressure (MAP. Multi-level general linear mixed effects models were used to examine the predictive relationship between muscular strength and endurance and MetS, controlling for the effect of aerobic fitness and the clustering of children within classrooms and schools. Children who were in the middle and upper tertiles for muscular strength and endurance associated with a lower (more favorable MetS score (middle tertile: β = −2.59, 95% C.I. [−4.23, −0.95], p < 0.05; upper tertile: β = −1.57, 95% C.I. [−3.20, −0.16], p < 0.05. The results suggest that higher levels of muscular strength and endurance relate to lower cardio-metabolic risk, independent of aerobic fitness, in Hispanic children from low-income schools.

In-line photonic microcells based on the elliptical microfibers for refractive index sensors applications

Science.gov (United States)

Jin, Wa; Liu, Xuejing; Jin, Wei

2017-10-01

We report the fabrication of in-line photonic microcells (PMCs) by encapsulating tapered elliptical microfibers (MFs) inside glass tubes. The encapsulation does not change the optical property of the MF but protects the elliptical MF from external disturbance and contamination and makes the micro-laboratory robust. Such micro-laboratory can be easily integrated into standard fiber-optic circuits with low loss, making the elliptical MF-based devices more practical for real-world applications. Evanescent field sensing is realized by fabricating micro-channel on the PMC for ingress/egress of sample liquids/gas. Based on the encapsulated elliptical MF PMCs, we demonstrated RI sensitivity of 2024 nm per refractive index unit (nm/RIU) in gaseous environment and 21231 nm/RIU in water.

The case for indexed price caps for U.S. electric utilities

International Nuclear Information System (INIS)

Lowry, M.N.

1991-01-01

Indexed price caps are a promising alternative to traditional, cost-of-service utility rate regulation. In just a decade, they have sprung from the drawing boards of economists to use by major utilities in a number of industries. Several authors have discussed the merits of indexed price caps for U.S. electric utilities. Despite their efforts, many parties to electric utility policy making are unfamiliar with the subject. This is unsurprising given the policy controversies that already embroil the industry. It is also unfortunate, since indexed price caps may help solve some of the problems that prompt these controversies. Indexed price caps can improve electric utility rate regulation in two ways. Utilities would have strong incentives to improve performance without the micromanagement that increasingly characterizes state-level regulation. Utilities could also be granted more extensive marketing freedoms, since indexes can protect customers from cross-subsidization. Two areas of concern about indexed price cap plans have emerged in recent discussions that the author has held with officials of electric utilities, intervenor groups, and regulatory agencies. Officials are often unclear on plan details, and therefore may not appreciate the degree of flexibility that is possible in plan design. Confusion over the available options in price cap adjustment indexes and the logic behind them is especially widespread. Officials also desire a clearer expression of how indexed price caps can coexist with current regulatory initiatives. This article details the major attributes of index plans, provides a brief history of indexing, discusses index design options in depth, and concludes with a vision of how indexed price caps can be made operational in today's electric utility industry

Unbounding the mental number line – New evidence on children’s spatial representation of numbers

Directory of Open Access Journals (Sweden)

Tanja eLink

2014-01-01

Full Text Available Number line estimation (i.e., indicating the position of a given number on a physical line is a standard assessment of children’s spatial representation of number magnitude. Importantly, there is an ongoing debate on the question in how far the bounded task version with start and endpoint given (e.g., 0 and 100 might induce specific estimation strategies and thus may not allow for unbiased inferences on the underlying representation. Recently, a new unbounded version of the task was suggested with only the start point and a unit fixed (e.g., the distance from 0 to 1. In adults this task provided a less biased index of the spatial representation of number magnitude. Yet, so far there are no children data available for the unbounded number line estimation task. Therefore, we conducted a cross-sectional study on primary school children performing both, the bounded and the unbounded version of the task. We observed clear evidence for systematic strategic influences (i.e., the consideration of reference points in the bounded number line estimation task for children older than grade two whereas there were no such indications for the unbounded version for any one of the age groups. In summary, the current data corroborate the unbounded number line estimation task to be a valuable tool for assessing children's spatial representation of number magnitude in a systematic and unbiased manner. Yet, similar results for the bounded and the unbounded version of the task for first- and second-graders may indicate that both versions of the task might assess the same underlying representation for relatively younger children - at least in number ranges familiar to the children assessed. This is of particular importance for inferences about the nature and development of children's magnitude representation.

Assessment of respiratory muscle strength in children according to the classification of body mass index

Directory of Open Access Journals (Sweden)

George Jung da Rosa

2014-06-01

Full Text Available OBJECTIVE: To assess and compare the respiratory muscle strength among eutrophic, overweight and obese school children, as well as to identify anthropometric and respiratory variables related to the results.METHODS: Cross-sectional survey with healthy schoolchildren aged 7-9 years old, divided into three groups: Normal weight, Overweight and Obese. The International Study of Asthma and Allergies in Childhood (ISAAC questionnaire was applied. The body mass index (BMI was evaluated, as well as the forced expiratory volume in one second (FEV1 with a portable digital device. The maximal inspiratory and expiratory pressures (MIP and MEP were measured by a digital manometer. Comparisons between the groups were made by Kruskal-Wallis test. Spearman's correlation coefficient was used to analyze the correlations among the variables.RESULTS: MIP of eutrophic school children was higher than MIP found in overweight (p=0.043 and obese (p=0.013 children. MIP was correlated with BMI percentile and weight classification (r=-0.214 and r=-0.256 and MEP was correlated with height (r=0.328. Both pressures showed strong correlation with each other in all analyses (r≥0.773, and less correlation with FEV1 (MIP - r=0.362 and MEP - r=0.494. FEV1 correlated with MEP in all groups (r: 0.429 - 0.569 and with MIP in Obese Group (r=0.565. Age was correlated with FEV1 (r=0.578, MIP (r=0.281 and MEP (r=0.328.CONCLUSIONS: Overweight and obese children showed lower MIP values, compared to eutrophic ones. The findings point to the influence of anthropometric variables on respiratory muscle strength in children.

Pain severity is associated with muscle strength and peak oxygen uptake in adults with fibromyalgia

Directory of Open Access Journals (Sweden)

Hooten WM

2014-05-01

Full Text Available W Michael Hooten,1,2 Jolene M Smith,3 Jason S Eldrige,1 David A Olsen,3 W David Mauck,1 Susan M Moeschler11Department of Anesthesiology, 2Department of Psychiatry and Psychology, Mayo Clinic College of Medicine, 3Mayo School of Graduate Medical Education, Rochester, MN, USABackground: The associations between pain, lower extremity strength, and aerobic conditioning have not been widely investigated in adults with fibromyalgia (FM. The principle objective of this study was to investigate the relationship between pain severity and knee strength in patients seeking treatment for FM. A secondary objective was to investigate the relationship between pain scores and aerobic conditioning.Methods: Three measures of knee strength (isokinetic extensor, isokinetic flexor, isometric extensor were quantified in the dominant leg of 69 adults with FM using a dynamometer at speeds of 60 degrees per second (60°/s and 180°/s. Peak oxygen uptake (VO2 was assessed using a cycle ergometer, and pain was assessed using the pain severity subscale of the Multidimensional Pain Inventory.Results: In univariable linear regression analyses using pain severity as the dependent variable, lesser values of isokinetic knee extensor strength at 60°/s (P=0.041 and 180°/s (P=0.010, isokinetic knee flexor strength at 60°/s (P=0.028 and 180°/s (P=0.003, and peak VO2 uptake (P=0.031 were predictive of greater pain severity scores. In multiple variable linear regression models adjusted for age, sex, body mass index, and opioid use, the following associations retained statistical significance; isokinetic knee extensor strength at 60°/s (P=0.020 and 180°/s (P=0.003, isokinetic knee flexor strength at 60°/s (P=0.015 and 180°/s (P=0.001, and peak VO2 uptake (P=0.014. However, no significant associations were found between pain severity and isometric knee extensor strength.Conclusion: The main findings from this study were that lesser values of isokinetic knee strength and peak VO

Joint laxity and the relationship between muscle strength and functional ability in patients with osteoarthritis of the knee.

Science.gov (United States)

van der Esch, M; Steultjens, M; Knol, D L; Dinant, H; Dekker, J

2006-12-15

To establish the impact of knee joint laxity on the relationship between muscle strength and functional ability in osteoarthritis (OA) of the knee. A cross-sectional study of 86 patients with OA of the knee was conducted. Tests were performed to determine varus-valgus laxity, muscle strength, and functional ability. Laxity was assessed using a device that measures the angular deviation of the knee in the frontal plane. Muscle strength was measured using a computer-driven isokinetic dynamometer. Functional ability was assessed by observation (100-meter walking test) and self report (Western Ontario and McMaster Universities Osteoarthritis Index [WOMAC]). Regression analyses were performed to assess the impact of joint laxity on the relationship between muscle strength and functional ability. In regression analyses, the interaction between muscle strength and joint laxity contributed to the variance in both walking time (P = 0.002) and WOMAC score (P = 0.080). The slope of the regression lines indicated that the relationship between muscle strength and functional ability (walking time, WOMAC) was stronger in patients with high knee joint laxity. Patients with knee OA and high knee joint laxity show a stronger relationship between muscle strength and functional ability than patients with OA and low knee joint laxity. Patients with OA, high knee joint laxity, and low muscle strength are most at risk of being disabled.

DETECTION OF REST-FRAME OPTICAL LINES FROM X-SHOOTER SPECTROSCOPY OF WEAK EMISSION-LINE QUASARS

International Nuclear Information System (INIS)

Plotkin, Richard M.; Gallo, Elena; Shemmer, Ohad; Trakhtenbrot, Benny; Anderson, Scott F.; Brandt, W. N.; Luo, Bin; Schneider, Donald P.; Fan, Xiaohui; Lira, Paulina; Richards, Gordon T.; Strauss, Michael A.; Wu, Jianfeng

2015-01-01

Over the past 15 yr, examples of exotic radio-quiet quasars with intrinsically weak or absent broad emission line regions (BELRs) have emerged from large-scale spectroscopic sky surveys. Here, we present spectroscopy of seven such weak emission line quasars (WLQs) at moderate redshifts (z = 1.4–1.7) using the X-shooter spectrograph, which provides simultaneous optical and near-infrared spectroscopy covering the rest-frame ultraviolet (UV) through optical. These new observations effectively double the number of WLQs with spectroscopy in the optical rest-frame, and they allow us to compare the strengths of (weak) high-ionization emission lines (e.g., C iv) to low-ionization lines (e.g., Mg ii, Hβ, Hα) in individual objects. We detect broad Hβ and Hα emission in all objects, and these lines are generally toward the weaker end of the distribution expected for typical quasars (e.g., Hβ has rest-frame equivalent widths ranging from 15–40 Å). However, these low-ionization lines are not exceptionally weak, as is the case for high-ionization lines in WLQs. The X-shooter spectra also display relatively strong optical Fe ii emission, Hβ FWHM ≲ 4000 km s −1 , and significant C iv blueshifts (≈1000–5500 km s −1 ) relative to the systemic redshift; two spectra also show elevated UV Fe ii emission, and an outflowing component to their (weak) Mg ii emission lines. These properties suggest that WLQs are exotic versions of “wind-dominated” quasars. Their BELRs either have unusual high-ionization components, or their BELRs are in an atypical photoionization state because of an unusually soft continuum

Atomic data and spectral line intensities for Fe XVII

International Nuclear Information System (INIS)

Bhatia, A.K.; Doschek, G.A.

2003-01-01

Electron impact collision strengths and spontaneous radiative decay rates are calculated for Fe XVII. The data pertain to the 73 levels of the configurations, 2s 2 2p 6 , 2s 2 2p 5 3s, 2s 2 2p 5 3p 2s 2 2p 5 3d, 2s2p 6 3s, 2s2p 6 3p, 2s2p 6 3d, 2s 2 2p 5 4s, 2s 2 2p 5 4p, 2s 2 2p 5 4d, 2s2p 6 4s, 2s2p 6 4p, and 2s2p 6 4d. Collision strengths are calculated at 11 incident electron energies: 58.5, 65.0, 70.0, 76.0, 85.0, 127.5, 170.0, 212.5, 255.0, 340.0, and 425.0 Ry. This work is an improvement over our earlier work on Fe XVII in two respects: (1) configurations involving 4s, 4p, and 4d electrons have been added and (2) a broader range of incident electron energies is used in the computation of collision strengths and excitation rate coefficients. Relative spectral line intensities are calculated for astrophysically important transitions. These are obtained by computing the excitation rate coefficients (cm 3 s -1 ), i.e., the collision strengths integrated over a Maxwellian electron distribution, and then solving the equations of detailed balance for the populations of the 73 energy levels, assuming a collisional excitation model and an electron temperature of 4 x 10 6 K. This temperature is typical for Fe XVII when formed in equilibrium by collisional ionization and recombination. Using the excitation rate coefficients and the radiative decay rates, level populations are computed for five electron densities and are given in this paper

Bone Mechanical Strength Estimation from Micro X-ray CT Image

National Research Council Canada - National Science Library

Matani, A

2001-01-01

... (Bone Mineral Density), an index to evaluate the mechanical strength of the bone, does not always reflect the strength, On the other hand, micro X-ray CT has revealed the inner structure of bone, Under such circumstances...

Investigation of Bond Strength in Centrifugal Lining of Babbitt on Cast Iron

Science.gov (United States)

Diouf, Papa; Jones, Alan

2010-03-01

The quality of the bond between Babbitt metal and a cast iron substrate was evaluated for centrifugal casting and static casting using the Chalmers bond strength method and scanning electron microscopy (SEM). The effect of three different centrifugal casting parameters, the speed of revolution, the pouring rate, and the cooling rate, was investigated. The bond strength and the microstructure at the bond interface were predominantly affected by the cooling rate, with a fast cooling rate resulting in better properties. The speed of revolution and the pouring rate only had a small effect on the bond strength, with faster revolution and faster pouring rate resulting in slightly better bonds.

Correlation between Bieniawski’s RMR index and Barton’s Q index in fine-grained sedimentary rock formations

Directory of Open Access Journals (Sweden)

J. D. Fernández-Gutiérrez

2017-09-01

Full Text Available From the XX century, various rock mass classification systems have been proposed. Among them, the Bieniawski’s RMR system and Barton’s Q system have emerged as the most used rock mass classification worldwide. Correlations between both indices have been proposed, usually with a wide scattering of the data used in deriving the equations. However, it has been observed that correlations established for a specific geological unit fit better. The aim of this paper is to propose a correlation between RMR and Q indices for fine-grained sedimentary rock formations, normally found in the area of Bilbao (Spain, by means of the collected data during the excavation of the tunnel Etxebarri-Casco Viejo of the line 3 of the Metropolitan Railway of Bilbao. Obtained equation shows a high correlation coefficient and a unique relationship between the two classification systems has been proposed, not depending on the choice of the independent variable.

Measurements of (p,γ) resonance strengths in the s-d shell

NARCIS (Netherlands)

Engelbertink, G.A.P.; Endt, P.M.

1966-01-01

Resonace strengths of selected resonances in the Ep=0.3−2.1 MeV region in the (p, γ) reactions on 23Na, 24–24Mg, 27Al, 28–30Si, 31P, 32, 34S, 35, 37Cl, 39, 41K and 40Ca are compared through relative yield measurements, using targets of many different chemical compounds, each containing at least two

Estimation of the strength of Nubian sandstone formation from point load test index and other simple parameters

Directory of Open Access Journals (Sweden)

Zein Abdul Karim M.

2018-01-01

Full Text Available This study investigates the correlation of the uniaxial compressive strength (UCS and the point load test (PLT index Is(50, bulk density, water absorption and the RQD properties of the Sudanese Nubian sandstone formation. The UCS being is the rock property needed in engineering practice but its determination is tedious, time consuming and expensive. Alternatively, the UCS may be indirectly evaluated through establishing relationships with rock parameters which are easier, cheaper and more convenient to determine in the laboratory or in the field. An extensive laboratory testing was executed to determine the above rock properties for many NSF samples taken from Khartoum State and other areas. Statistical analysis was performed on the test data and a reliable linear regression equation has been developed with a UCS to PLT Is(50 conversion factor of 10.18 and may be applied to estimate the strength of the Sudanese sandstone formation. The developed correlation is in good agreement with few of the many methods published for similar rock types which indicates that large errors may result in from applying an inappropriate UCS prediction method. Thus, it is important to establish separate correlations or validate published correlations to check their suitability for a specific rock types and local geologies. Useful correlation relationships of reasonable accuracy were also established for rough estimation of the UCS from the bulk density, water absorption and the RQD properties of the Nubian sandstone formation.

Identification of the 1s2s2p 4P5/2-->1s22s 2S1/2 magnetic quadrupole inner-shell satellite line in the Ar16+ K-shell x-ray spectrum

Science.gov (United States)

Beiersdorfer, P.; Bitter, M.; Hey, D.; Reed, K. J.

2002-09-01

We have identified the dipole-forbidden 1s2s2p 4P5/2-->1s22s 2S1/2 transition in lithiumlike Ar15+ in high-resolution K-shell x-ray emission spectra recorded at the Livermore EBIT-II electron-beam ion trap and the Princeton National Spherical Tokamak Experiment. Unlike other Ar15+ satellite lines, which can be excited by dielectronic recombination, the line is exclusively excited by electron-impact excitation. Its predicted radiative rate is comparable to that of the well-known 1s2p 3P1-->1s2 1S0 magnetic quadrupole transition in heliumlike Ar16+. As a result, it can also only be observed in low-density plasma. We present calculations of the electron-impact excitation cross sections of the innershell excited Ar15+ satellite lines, including the magnetic sublevels needed for calculating the linear line polarization. We compare these calculations to the relative magnitudes of the observed 1s2s2p-->1s22s transitions and find good agreement, confirming the identification of the lithiumlike 1s2s2p 4P5/2-->1s22s 2S1/2 magnetic quadrupole line.

Direct relationship between breakdown strength and tracking index of composites

DEFF Research Database (Denmark)

Madsen, Søren Find; Henriksen, Mogens; Holbøll, Joachim

2006-01-01

. The breakdown field strength of specimens cut from similar samples is determined by a new method capable of estimating the stressed volume. The results from the two tests are finally compared and incorporated in a single analytical formula. All test specimens are supplied by Danish manufacturers of wind turbine...

TRAC-PF1/MOD 1 independent assessment: Semiscale MOD-2A feedwater-line break (S-SF-3) and steam-line break (S-SF-5) tests

International Nuclear Information System (INIS)

Dobranich, D.

1985-11-01

The TRAC-PF1/MOD1 independent assessment project at Sandia is part of an overall effort funded by the NRC to determine the ability of various systems codes to predict the detailed thermal/hydraulic response of LWRs during accident and off-normal conditions. As part of this effort, calculations for Semiscale Mod-2A test S-SF-3, a feedwater-line break test, and S-SF-5, a steam-line break test, were performed with TRAC-PF1/MOD1. Most aspects of both the S-SF-3 and S-SF-5 steady-state calculations were found to be in good agreement with data. However, the need for a better steam separator model was identified from the S-SF-3 calculation. Overall, the qualitative behavior of both transients was calculated reasonably well; however, there were some discrepancies in the prediction of the quantitative behavior. The results for the S-SF-3 transient calculation indicate that the primary-to-secondary heat transfer degradation began too early. This was possibly due to overprediction of entrainment in the steam generator boiler, leading to an incorrect calculation of the secondary-side fluid distribution during the steady state. However, there was insufficient data to verify this. Results for the S-SF-5 transient calculation indicate that the primary-side fluid temperature response to a steam-line break was in reasonable agreement with data but the pressure response did not coincide with the data. Uncertainties in the data are sufficient to prevent us from determining the exact cause of this discrepancy, but there is indirect evidence that the calculated rate of phase change in the pressurizer was incorrect. 16 refs., 73 figs., 13 tabs

Forecasting the compressive strength of soil-concretedepending on ...

African Journals Online (AJOL)

One of the most important physical and mechanical properties of soil-concrete is the compressive strength. To this end we carried out a study of soil-concrete strength depending on its curing conditions and percentage of cement. For our study we used loam soil with the plasticity index of Ip = 12.3, Portland cement of type I, ...

Strength and tempo of directional selection in the wild

OpenAIRE

Hoekstra, H. E.; Hoekstra, J. M.; Berrigan, D.; Vignieri, S. N.; Hoang, A.; Hill, C. E.; Beerli, P.; Kingsolver, J. G.

2001-01-01

Directional selection is a major force driving adaptation and evolutionary change. However, the distribution, strength, and tempo of phenotypic selection acting on quantitative traits in natural populations remain unclear across different study systems. We reviewed the literature (1984–1997) that reported the strength of directional selection as indexed by standardized linear selection gradients (β). We asked how strong are viability and sexual selection, and whether strength of selection is ...

FBQS J1644+2619: multiwavelength properties and its place in the class of γ-ray emitting Narrow Line Seyfert 1s

Science.gov (United States)

Larsson, J.; D'Ammando, F.; Falocco, S.; Giroletti, M.; Orienti, M.; Piconcelli, E.; Righini, S.

2018-05-01

A small fraction of Narrow Line Seyfert 1s (NLSy1s) are observed to be γ-ray emitters. Understanding the properties of these sources is of interest since the majority of NLSy1s are very different from typical blazars. Here, we present a multifrequency analysis of FBQS J1644+2619, one of the most recently discovered γ-ray emitting NLSy1s. We analyse an ˜80 ks XMM-Newton observation obtained in 2017, as well as quasi-simultaneous multiwavelength observations covering the radio-γ-ray range. The spectral energy distribution of the source is similar to the other γ-ray NLSy1s, confirming its blazar-like nature. The X-ray spectrum is characterized by a hard photon index (Γ = 1.66) above 2 keV and a soft excess at lower energies. The hard photon index provides clear evidence that inverse Compton emission from the jet dominates the spectrum, while the soft excess can be explained by a contribution from the underlying Seyfert emission. This contribution can be fitted by reflection of emission from the base of the jet, as well as by Comptonization in a warm, optically thick corona. We discuss our results in the context of the other γ-ray NLSy1s and note that the majority of them have similar X-ray spectra, with properties intermediate between blazars and radio-quiet NLSy1s.

The Strength Compass

DEFF Research Database (Denmark)

Ledertoug, Mette Marie

In the Ph.D-project ͚Strengths-based Learning - Children͛s character strengths as a means to their learning potential͛ 750 Danish children have assessed ͚The Strength Compass͛ in order to identify their strengths and to create awareness of strengths. This was followed by a strengths......-based intervention program in order to explore the strengths. Finally different methods to apply the strength in everyday life at school were applied. The paper presentation will show the results for strengths display for children aged 6-16 in different categories: Different age groups: Are the same strengths...... present in both small children and youths? Gender: Do the results show differences between the two genders? Danish as a mother- tongue language: Do the results show any differences in the strengths display when considering different language and cultural backgrounds? Children with Special Needs: Do...

Redox Buffer Strength

Science.gov (United States)

de Levie, Robert

1999-04-01

The proper functioning of enzymes in bodily fluids requires that the pH be maintained within rather narrow limits. The first line of defense against large pH fluctuations in such fluids is the passive control provided by the presence of pH buffers. The ability of pH buffers to stabilize the pH is indicated by the buffer value b introduced in 1922 by van Slyke. It is equally important for many enzymes that the redox potential is kept within a narrow range. In that case, stability of the potential is most readily achieved with a redox buffer. In this communication we define the redox buffer strength by analogy with acid-base buffer strength.

Bone strength and athletic ability in hominids: Ardipithecus ramidus to Homo sapiens

Science.gov (United States)

Lee, S. A.

2013-03-01

The ability of the femur to resist bending stresses is determined by its midlength cross-sectional geometry, its length and the elastic properties of the mineral part of the bone. The animal's athletic ability, determined by a ``bone strength index,'' is limited by this femoral bending strength in relation to the loads on the femur. This analysis is applied to the fossil record for Homo sapiens, Homo neanderthalensis, Homo erectus, Homo habilis, Australopithecus afarensis and Ardipithecus ramidus. Evidence that the femoral bone strength index of modern Homo sapiens has weakened over the last 50,000 years is found.

Efficacy of S-1 plus nedaplatin compared to standard second-line chemotherapy in EGFR-negative lung adenocarcinoma after failure of first-line chemotherapy.

Science.gov (United States)

Tang, Yu; Wang, Wei; Teng, Xiu-Zhi; Shi, Lin

2014-09-01

For patients with advanced non-small cell lung adenocarcinoma that fail to respond to first-line chemotherapy and that do not involve epidermal growth factor receptor (EGFR) mutations, previous empirical analysis showed that a single second-line chemotherapy agent may be inadequate for the control of further tumor development. This study examines the combination of S-1 drugs and nedaplatin that has no cross-resistance to first-line treatments; 179 cases of IIIb-IV stage non-small-cell lung adenocarcinoma that failed to respond to first-line chemotherapy were included, and these subjects did not have mutated EGFRs. In the present study, S-1 plus nedaplatin chemotherapy was better than standard second-line chemotherapy options in the treatment of advanced lung adenocarcinoma that did not involve EGFR mutations and that failed to respond to first-line chemotherapy. Additionally, the combination of S-1 and nedaplatin seemed to be well tolerated, making this chemotherapy technique a potentially strong candidate for the treatment of advanced non-small-cell lung adenocarcinoma.

Effective selection criteria for screening drought tolerant recombinant inbred lines of sunflower

Directory of Open Access Journals (Sweden)

Abdi Nishtman

2013-01-01

Full Text Available In this study, seventy two sunflower recombinant inbred lines were tested for their yielding ability under both water-stressed and well-watered states. The inbred lines were evaluated in a rectangular 8´9 lattice design with two replications in both well-watered and water-stressed conditions, separately. Eight drought tolerance indices including stability tolerance index (STI, mean productivity (MP, geometric mean productivity (GMP, harmonic mean (HM, stress susceptibility index (SSI, tolerance index (TOL, yield index (YI and yield stability index (YSI were calculated based on grain yield for every genotype. Results showed the highest values of mean productivity (MP index, geometric mean productivity (GMP, yield index (YI, harmonic mean (HM and stress tolerance index (STI indices for ‘C134a’ inbred line and least values of stress susceptibility index (SSI and tolerance (TOL for C61 inbred line. According to correlation of indices with yield performance under both drought stress and non-stress states and principle component analysis, indices including HM, MP, GMP and STI could properly distinguish drought tolerant sunflower inbred lines with high yield performance under both states. Cluster analysis of inbred lines using Ys, Yp and eight indices, categorized them into four groups including 19, 6, 26 and 19 inbred lines.

Asymmetric multi-fractality in the U.S. stock indices using index-based model of A-MFDFA

International Nuclear Information System (INIS)

Lee, Minhyuk; Song, Jae Wook; Park, Ji Hwan; Chang, Woojin

2017-01-01

Highlights: • ‘Index-based A-MFDFA’ model is proposed to assess the asymmetric multi-fractality. • The asymmetric multi-fractality in the U.S. stock indices are investigated using ‘Index-based’ and ‘Return-based’ A-MFDFA. • The asymmetric feature is more significantly identified by ‘Index-based’ model than ‘return-based’ model. • Source of multi-fractality and time-varying features are analyzed. - Abstract: We detect the asymmetric multi-fractality in the U.S. stock indices based on the asymmetric multi-fractal detrended fluctuation analysis (A-MFDFA). Instead using the conventional return-based approach, we propose the index-based model of A-MFDFA where the trend based on the evolution of stock index rather than stock price return plays a role for evaluating the asymmetric scaling behaviors. The results show that the multi-fractal behaviors of the U.S. stock indices are asymmetric and the index-based model detects the asymmetric multi-fractality better than return-based model. We also discuss the source of multi-fractality and its asymmetry and observe that the multi-fractal asymmetry in the U.S. stock indices has a time-varying feature where the degree of multi-fractality and asymmetry increase during the financial crisis.

Stellar Laboratories: New GeV and Ge VI Oscillator Strengths and their Validation in the Hot White Dwarf RE0503-289

Science.gov (United States)

Rauch, T.; Werner, K.; Biemont, E.; Quinet, P.; Kruk, J. W.

2013-01-01

State-of-the-art spectral analysis of hot stars by means of non-LTE model-atmosphere techniques has arrived at a high level of sophistication. The analysis of high-resolution and high-S/N spectra, however, is strongly restricted by the lack of reliable atomic data for highly ionized species from intermediate-mass metals to trans-iron elements. Especially data for the latter has only been sparsely calculated. Many of their lines are identified in spectra of extremely hot, hydrogen-deficient post-AGB stars. A reliable determination of their abundances establishes crucial constraints for AGB nucleosynthesis simulations and, thus, for stellar evolutionary theory. Aims. In a previous analysis of the UV spectrum of RE 0503-289, spectral lines of highly ionized Ga, Ge, As, Se, Kr, Mo, Sn, Te, I, and Xe were identified. Individual abundance determinations are hampered by the lack of reliable oscillator strengths. Most of these identified lines stem from Ge V. In addition, we identified Ge VI lines for the first time. We calculated Ge V and Ge VI oscillator strengths in order to reproduce the observed spectrum. Methods. We newly calculated Ge V and Ge VI oscillator strengths to consider their radiative and collisional bound-bound transitions in detail in our non-LTE stellar-atmosphere models for the analysis of the Ge IV-VI spectrum exhibited in high-resolution and high-S/N FUV (FUSE) and UV (ORFEUS/BEFS, IUE) observations of RE 0503-289. Results. In the UV spectrum of RE 0503-289, we identify four Ge IV, 37 Ge V, and seven Ge VI lines. Most of these lines are identified for the first time in any star. We can reproduce almost all Ge IV, GeV, and Ge VI lines in the observed spectrum of RE 0503-289 (T(sub eff) = 70 kK, log g = 7.5) at log Ge = -3.8 +/- 0.3 (mass fraction, about 650 times solar). The Ge IV/V/VI ionization equilibrium, that is a very sensitive T(sub eff) indicator, is reproduced well. Conclusions. Reliable measurements and calculations of atomic data are a

The Cardy limit of the topologically twisted index and black strings in AdS{sub 5}

Energy Technology Data Exchange (ETDEWEB)

Hosseini, Seyed Morteza; Nedelin, Anton; Zaffaroni, Alberto [Dipartimento di Fisica, Università di Milano-Bicocca,I-20126 Milano (Italy); INFN, Sezione di Milano-Bicocca,I-20126 Milano (Italy)

2017-04-04

We evaluate the topologically twisted index of a general four-dimensional N=1 gauge theory in the “high-temperature' limit. The index is the partition function for N=1 theories on S{sup 2}×T{sup 2}, with a partial topological twist along S{sup 2}, in the presence of background magnetic fluxes and fugacities for the global symmetries. We show that the logarithm of the index is proportional to the conformal anomaly coefficient of the two-dimensional N=(0,2) SCFTs obtained from the compactification on S{sup 2}. We also present a universal formula for extracting the index from the four-dimensional conformal anomaly coefficient and its derivatives. We give examples based on theories whose holographic duals are black strings in type IIB backgrounds AdS{sub 5}×SE{sub 5}, where SE{sub 5} are five-dimensional Sasaki-Einstein spaces.

Influence of Welding Time on Tensile-Shear Strength of Linear Friction Welded Birch (Betula pendula L. Wood

Directory of Open Access Journals (Sweden)

Jussi Ruponen

2015-04-01

Full Text Available The purpose of this work was to determine the optimal welding time for linear friction welding of birch (Betula pendula L. wood while keeping the other parameters constant and at similar levels compared to other species in a similar density range. Specimens with dimensions of 20 × 5 × 150 mm3 were welded together, and the influence of welding time (2.5, 3.0, 3.5, and 4.0 s on the mechanical properties of the specimens was determined. The studies included a tensile-shear strength test as well as visual estimation of wood failure percentage (WFP. Additionally, X-ray microtomographic imaging was used to investigate and characterise the bond line properties as a non-destructive testing method. The highest mean tensile-shear strength, 7.9 MPa, was reached with a welding time of 3.5 s. Generally, all four result groups showed high, yet decreasing proportional standard deviations as the welding time increased. X-ray microtomographic images and analysis express the heterogeneity of the weld line clearly as well. According to the averaged group-wise results, WFP and tensile-shear strength correlated positively with an R2 of 0.93. An extrapolation of WFP to 65% totals a tensile-shear strength of 10.6 MPa, corresponding to four common adhesive bonds determined for beech.

Predicting Soil Strength in Terms of Cone Index and California Bearing Ratio for Trafficability

Science.gov (United States)

2016-03-01

in Equation 4 (Anderson 1983). One can see the variation to Equation 1 (McDaniel and Smith 1971). Collins and Molthan suggested the lower and upper...and the amount of drainage, as defined by a wetness index term ( Collins 1971; Molthan 1967). ERDC/GSL TN-16-1 March 2016 4 2 123 0 008 0 693 4...since its development in the 1940s. It was devised by Jim Porter ( 1 9 5 0 ) of the California Division of Highways. Porter developed curves showing the

Give Me Strength.

Institute of Scientific and Technical Information of China (English)

维拉

1996-01-01

Mort had an absolutely terrible day at the office.Everythingthat could go wrong did go wrong.As he walked home he could beheard muttering strange words to himself:“Oh,give me strength,give me strength.”Mort isn’t asking for the kind of strength thatbuilds strong muscles:he’s asking for the courage or ability to

Determinants of Police Strength in Large U.S. Cities during the 1990s: A Fixed-Effects Panel Analysis

Science.gov (United States)

McCarty, William P.; Ren, Ling; Zhao, Jihong

2012-01-01

The 1990s represented a unique decade in which to analyze the determinants of police strength in the United States. This decade was a time in which crime initially increased, then substantially decreased. Furthermore, this decade also was characterized by increases in the minority population throughout large American cities. Finally, the 1990s…

Relation between body mass index percentile and muscle strength and endurance

Directory of Open Access Journals (Sweden)

Noha Abdel Kader Abdel Kader Hasan

2016-10-01

Conclusion: The study shows that the BMI of children had a positive correlation with the muscle strength of quadriceps, triceps, and abdominal muscles while a negative correlation with the endurance time of these muscles.

Strengths only or strengths and relative weaknesses? A preliminary study.

Science.gov (United States)

Rust, Teri; Diessner, Rhett; Reade, Lindsay

2009-10-01

Does working on developing character strengths and relative character weaknesses cause lower life satisfaction than working on developing character strengths only? The present study provides a preliminary answer. After 76 college students completed the Values in Action Inventory of Strengths (C. Peterson & M. E. P. Seligman, 2004), the authors randomly assigned them to work on 2 character strengths or on 1 character strength and 1 relative weakness. Combined, these groups showed significant gains on the Satisfaction With Life Scale (E. Diener, R. A. Emmons, R. J. Larsen, & S. Griffin, 1985), compared with a 32-student no-treatment group. However, there was no significant difference in gain scores between the 2-strengths group and the 1-character-strength-and-1-relative-character-weakness group. The authors discuss how focusing on relative character weaknesses (along with strengths) does not diminish-and may assist in increasing-life satisfaction.

Calculating the Candy Price Index: A Classroom Inflation Experiment.

Science.gov (United States)

Hazlett, Denise; Hill, Cynthia D.

2003-01-01

Outlines how students develop a price index based on candy-purchasing decisions made by class members. Explains that students used the index to practice calculating inflation rates and to consider the strengths and weaknesses of the consumer price index (CPI). States that the exercise has been used in introductory and intermediate macroeconomics…

Evaluating Variability and Uncertainty of Geological Strength Index at a Specific Site

Science.gov (United States)

Wang, Yu; Aladejare, Adeyemi Emman

2016-09-01

Geological Strength Index (GSI) is an important parameter for estimating rock mass properties. GSI can be estimated from quantitative GSI chart, as an alternative to the direct observational method which requires vast geological experience of rock. GSI chart was developed from past observations and engineering experience, with either empiricism or some theoretical simplifications. The GSI chart thereby contains model uncertainty which arises from its development. The presence of such model uncertainty affects the GSI estimated from GSI chart at a specific site; it is, therefore, imperative to quantify and incorporate the model uncertainty during GSI estimation from the GSI chart. A major challenge for quantifying the GSI chart model uncertainty is a lack of the original datasets that have been used to develop the GSI chart, since the GSI chart was developed from past experience without referring to specific datasets. This paper intends to tackle this problem by developing a Bayesian approach for quantifying the model uncertainty in GSI chart when using it to estimate GSI at a specific site. The model uncertainty in the GSI chart and the inherent spatial variability in GSI are modeled explicitly in the Bayesian approach. The Bayesian approach generates equivalent samples of GSI from the integrated knowledge of GSI chart, prior knowledge and observation data available from site investigation. Equations are derived for the Bayesian approach, and the proposed approach is illustrated using data from a drill and blast tunnel project. The proposed approach effectively tackles the problem of how to quantify the model uncertainty that arises from using GSI chart for characterization of site-specific GSI in a transparent manner.

CubeIndexer: Indexer for regions of interest in data cubes

Science.gov (United States)

Chilean Virtual Observatory; Araya, Mauricio; Candia, Gabriel; Gregorio, Rodrigo; Mendoza, Marcelo; Solar, Mauricio

2015-12-01

CubeIndexer indexes regions of interest (ROIs) in data cubes reducing the necessary storage space. The software can process data cubes containing megabytes of data in fractions of a second without human supervision, thus allowing it to be incorporated into a production line for displaying objects in a virtual observatory. The software forms part of the Chilean Virtual Observatory (ChiVO) and provides the capability of content-based searches on data cubes to the astronomical community.

Weldability prediction of high strength steel S960QL after weld thermal cycle simulation

Directory of Open Access Journals (Sweden)

M. Dunđer

2014-10-01

Full Text Available This paper presents weld thermal cycle simulation of high strength steel S960QL, and describes influence of cooling time t8/5 on hardness and impact toughness of weld thermal cycle simulated specimens. Furthermore, it presents analysis of characteristic fractions done by electron scanning microscope which can contribute to determination of welding parameters for S960QL steel.

First-principles studies of Te line-ordered alloys in a MoS2 monolayer

Science.gov (United States)

Andriambelaza, N. F.; Mapasha, R. E.; Chetty, N.

2018-04-01

The thermodynamic stability, structural and electronic properties of Te line-ordered alloys are investigated using density functional theory (DFT) methods. Thirty four possible Te line-ordered alloy configurations are found in a 5×5 supercell of a MoS2 monolayer. The calculated formation energies show that the Te line-ordered alloy configurations are thermodynamically stable at 0 K and agree very well with the random alloys. The lowest energy configurations at each concentration correspond to the configuration where the Te atom rows are far apart from each other (avoiding clustering) within the supercell. The variation of the lattice constant at different concentrations obey Vegard's law. The Te line-ordered alloys fine tune the band gap of a MoS2 monolayer although deviating from linearity behavior. Our results suggest that the Te line-ordered alloys can be an effective way to modulate the band gap of a MoS2 monolayer for nanoelectronic, optoelectronic and nanophotonic applications.

Correlation between maximum isometric strength variables and specific performance of Brazilian military judokas

Directory of Open Access Journals (Sweden)

Michel Moraes Gonçalves

2017-06-01

Full Text Available It was our objective to correlate specific performance in the Special Judo Fitness Test (SJFT and the maximum isometric handgrip (HGSMax, scapular traction (STSMax and lumbar traction (LTSMax strength tests in military judo athletes. Twenty-two military athletes from the judo team of the Brazilian Navy Almirante Alexandrino Instruction Centre, with average age of 26.14 ± 3.31 years old, and average body mass of 83.23 ± 14.14 kg participated in the study. Electronic dynamometry tests for HGSMax, STSMax and LTSMax were conducted. Then, after approximately 1 hour-interval, the SJFT protocol was applied. All variables were adjusted to the body mass of the athletes. Pearson correlation coefficient for statistical analysis was used. The results showed moderate negative correlation between the SJFT index and STSMax (r= -0.550, p= 0.008, strong negative correlations between the SJFT index and HGSMax (r= -0.706, p< 0.001, SJFT index and LTSMax (r= -0.721; p= 0.001, besides the correlation between the sum of the three maximum isometric strength tests and the SJFT index (r= -0.786, p< 0.001. This study concludes that negative correlations occur between the SJFT index and maximum isometric handgrip, shoulder and lumbar traction strength and the sum of the three maximum isometric strength tests in military judokas.

Differential strengths of selection on S-RNases from Physalis and Solanum (Solanaceae

Directory of Open Access Journals (Sweden)

Kohn Joshua R

2011-08-01

Full Text Available Abstract Background The S-RNases of the Solanaceae are highly polymorphic self-incompatibility (S- alleles subject to strong balancing selection. Relatively recent diversification of S-alleles has occurred in the genus Physalis following a historical restriction of S-allele diversity. In contrast, the genus Solanum did not undergo a restriction of S-locus diversity and its S-alleles are generally much older. Because recovery from reduced S-locus diversity should involve increased selection, we employ a statistical framework to ask whether S-locus selection intensities are higher in Physalis than Solanum. Because different S-RNase lineages diversify in Physalis and Solanum, we also ask whether different sites are under selection in different lineages. Results Maximum-likelihood and Bayesian coalescent methods found higher intensities of selection and more sites under significant positive selection in the 48 Physalis S-RNase alleles than the 49 from Solanum. Highest posterior densities of dN/dS (ω estimates show that the strength of selection is greater for Physalis at 36 codons. A nested maximum likelihood method was more conservative, but still found 16 sites with greater selection in Physalis. Neither method found any codons under significantly greater selection in Solanum. A random effects likelihood method that examines data from both taxa jointly confirmed higher selection intensities in Physalis, but did not find different proportions of sites under selection in the two datasets. The greatest differences in strengths of selection were found in the most variable regions of the S-RNases, as expected if these regions encode self-recognition specificities. Clade-specific likelihood models indicated some codons were under greater selection in background Solanum lineages than in specific lineages of Physalis implying that selection on sites may differ among lineages. Conclusions Likelihood and Bayesian methods provide a statistical approach to

Nonlinearity of the refractive index due to an excitonic molecule resonance state in CdS

International Nuclear Information System (INIS)

Baumert, R.; Broser, I.; Buschick, K.

1986-01-01

The authors report the observation of an intensity-dependent refractive-index nonlinearity in CdS due to a resonance state where an excitonic molecule is created by induced absorption of light. The refractive index n as a function of the incident laser photon energy E is measured directly by light refraction in thin crystal prisms. A renormalized dielectric function describes the measured n(E) spectra well. This strong refractive-index nonlinearity is well suited to produce an optical bistability and to further strengthen the evidence of CdS to be an important material for laser-induced dynamic gratings

Strengths-based Learning

DEFF Research Database (Denmark)

Ledertoug, Mette Marie

-being. The Ph.D.-project in Strength-based learning took place in a Danish school with 750 pupils age 6-16 and a similar school was functioning as a control group. The presentation will focus on both the aware-explore-apply processes and the practical implications for the schools involved, and on measurable......Strength-based learning - Children͛s Character Strengths as Means to their Learning Potential͛ is a Ph.D.-project aiming to create a strength-based mindset in school settings and at the same time introducing strength-based interventions as specific tools to improve both learning and well...

TIGER/Line Shapefile, 2015, nation, U.S., Rails National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Coastline National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Rails National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Coastline National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., Coastline National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

IUE observations of interstellar Si IV and C IV lines observed in the spectra of Wolf-Rayet stars

International Nuclear Information System (INIS)

Smith, L.J.; Willis, A.J.; Wilson, R.

1980-01-01

Recent IUE observations of Wolf-Rayet stars show narrow absorption lines in the highly ionized species of Si IV and C IV. The strengths of these 'interstellar' Si IV and C IV lines observed in the spectra of 10 WR stars and two other early-type stars are compared. Of the WR sample, six stars exhibit very strong Si IV and C IV lines (Wsub(lambda) approximately 0.3 to 0.5 A) whilst the other four stars show much weaker lines (Wsub(lambda) approximately 0.1 A). There is no correlation between the strengths of these lines with either stellar distance or colour excess. The weaker absorptions may arise in the individual stellar H II regions, the observed strengths being consistent with those expected for stars with Tsub(eff) = 30 000 K. Five of the other stars which exhibit very strong absorptions lie in the line of sight to active interstellar regions (Cygnus and Carina nebulae) and it is considered probable that, in addition to their H II region components, the bulk of the strong Si IV and C IV absorptions originate in hot gas associated with these active regions. In the case of the WN5 star HD 50896 violet-displaced components are observed in the interstellar lines of low ionization species. These are thought to be produced in the ring nebula S308 surrounding HD 50896. (author)

Design of the Yang magnetically-insulated transmission line

International Nuclear Information System (INIS)

Gu Yuanchao; Song Shenyi

2002-01-01

The authors have designed a new magnetically insulated transmission line (MITL) for the Yang accelerator. The differences between the existing line and the designing one are given. The electric strength of some special regions on the lines and the inductance of the lines have been calculated. The authors have checked the states of magnetic insulation on the designing line

Static and Dynamic Handgrip Strength Endurance: Test-Retest Reproducibility.

Science.gov (United States)

Gerodimos, Vassilis; Karatrantou, Konstantina; Psychou, Dimitra; Vasilopoulou, Theodora; Zafeiridis, Andreas

2017-03-01

This study investigated the reliability of static and dynamic handgrip strength endurance using different protocols and indicators for the assessment of strength endurance. Forty young, healthy men and women (age, 18-22 years) performed 2 handgrip strength endurance protocols: a static protocol (sustained submaximal contraction at 50% of maximal voluntary contraction) and a dynamic one (8, 10, and 12 maximal repetitions). The participants executed each protocol twice to assess the test-retest reproducibility. Total work and total time were used as indicators of strength endurance in the static protocol; the strength recorded at each maximal repetition, the percentage change, and fatigue index were used as indicators of strength endurance in the dynamic protocol. The static protocol showed high reliability irrespective of sex and hand for total time and work. The 12-repetition dynamic protocol exhibited moderate-high reliability for repeated maximal repetitions and percentage change; the 8- and 10-repetition protocols demonstrated lower reliability irrespective of sex and hand. The fatigue index was not a reliable indicator for the assessment of dynamic handgrip endurance. Static handgrip endurance can be measured reliably using the total time and total work as indicators of strength endurance. For the evaluation of dynamic handgrip endurance, the 12-repetition protocol is recommended, using the repeated maximal repetitions and percentage change as indicators of strength endurance. Practitioners should consider the static (50% maximal voluntary contraction) and dynamic (12 repeated maximal repetitions) protocols as reliable for the assessment of handgrip strength endurance. The evaluation of static endurance in conjunction with dynamic endurance would provide more complete information about hand function. Copyright © 2017 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Microstructure, Composition, and Impact Toughness Across the Fusion Line of High-Strength Bainitic Steel Weldments

Science.gov (United States)

Lan, Liangyun; Kong, Xiangwei; Chang, Zhiyuan; Qiu, Chunlin; Zhao, Dewen

2017-09-01

This paper analyzed the evolution of microstructure, composition, and impact toughness across the fusion line of high-strength bainitic steel weldments with different heat inputs. The main purpose was to develop a convenient method to evaluate the HAZ toughness quickly. The compositions of HAZ were insensitive to higher contents of alloy elements ( e.g., Ni, Mo) in the weld metal because their diffusion distance is very short into the HAZ. The weld metal contained predominantly acicular ferrite at any a heat input, whereas the main microstructures in the HAZ changed from lath martensite/bainite to upper bainite with the increasing heat input. The evolution of HAZ toughness in relation to microstructural changes can be revealed clearly combined with the impact load curve and fracture morphology, although the results of impact tests do not show an obvious change with heat input because the position of Charpy V notch contains the weld metal, HAZ as well as a part of base metal. As a result, based on the bead-on-plate welding tests, the welding parameter affecting the HAZ toughness can be evaluated rapidly.

A Case Study of Line-of-Balance based Schedule Planning and Control System

OpenAIRE

Seppänen, Olli; Aalto, Erno

2005-01-01

Line-of-Balance is a graphical technique which can be used to plan and manage work flow. It is suit-able for construction projects because of their large degree of repetition. Despite its strengths Line-of-Balance has not gained widespread use in construction industry internationally. However, it has been used as the principal scheduling tool in Finland since 1980s. As a result of two decades of research and use in industry, a comprehensive schedule planning and control system has been develo...

The dance’s influence on muscle strength of lower limbs on the elderly

Directory of Open Access Journals (Sweden)

Joseane Rodrigues da Silva

2011-09-01

Full Text Available The aim of this study was to evaluate the influence of dance in the lower limb muscle strength on the elderly. This research has a qualitative-quantitative aproach. The sample was composed by ten elderly of both sexes, who practiced ballroom dancing classes during twelve weeks. The evaluation was performed before and after the classes and it was composed by a questionnaire with personal data and medical history, “test stand and sit in 30 seconds” and a semi-structured interview with a guiding question regarding the perception of muscular strength of the elderly. The quantitative analysis was performed using the Student’s t-test with a significance level of p<0,05%. The qualitative analysis was made according directions proposed by Minayo (1994. The evaluation of muscle strength measured by the test of sitting and standing up, showed that four participants had a decreased and six had an increase in the number of movements executed, but not existed a significant statistical difference between the values before and after intervention (p=0,1934. However, the speech of the participants showed an improvement on the perception in relation muscle strength, mobility, joviality and self-esteem. It suggests that the effect of the dance, performed in the frequency used in this study, has an effect on the well-being and psychosocial sphere of the elderly. Playful activities in physical therapy performed by groups, bringing benefits, however, it should not be an isolated activity, it should be associated with a specific training to improve muscle strength related to the needs of each elderly.

The mechanical properties and microstructures of vanadium bearing high strength dual phase steels processed with continuous galvanizing line simulations

Science.gov (United States)

Gong, Yu

For galvanized or galvannealed steels to be commercially successful, they must exhibit several attributes: (i) easy and inexpensive processing in the hot mill, cold mill and on the coating line, (ii) high strength with good formability and spot weldability, and (iii) good corrosion resistance. At the beginning of this thesis, compositions with a common base but containing various additions of V or Nb with or without high N were designed and subjected to Gleeble simulations of different galvanizing(GI), galvannealing(GA) and supercooling processing. The results revealed the phase balance was strongly influenced by the different microalloying additions, while the strengths of each phase were somewhat less affected. Our research revealed that the amount of austenite formed during intercritical annealing can be strongly influenced by the annealing temperature and the pre-annealing conditions of the hot band (coiling temperature) and cold band (% cold reduction). In the late part of this thesis, the base composition was a low carbon steel which would exhibit good spot weldability. To this steel were added two levels of Cr and Mo for strengthening the ferrite and increasing the hardenability of intercritically formed austenite. Also, these steels were produced with and without the addition of vanadium in an effort to further increase the strength. Since earlier studies revealed a relationship between the nature of the starting cold rolled microstructure and the response to CGL processing, the variables of hot band coiling temperature and level of cold reduction prior to annealing were also studied. Finally, in an effort to increase strength and ductility of both the final sheet (general formability) and the sheared edges of cold punched holes (local formability), a new thermal path was developed that replaced the conventional GI ferrite-martensite microstructure with a new ferrite-martensite-tempered martensite and retained austenite microstructure. The new

Vietnam’s Evolving Poverty Index Map : Patterns and Implications for Policy

NARCIS (Netherlands)

Lanjouw, Peter; Marra, Marleen; Nguyen, Cuong

2017-01-01

This paper uses small area estimation techniques to estimate the poverty indexes of Vietnam’s provinces and districts in 2009. We find that poverty rates have become more spatially concentrated over time, which is consistent with widely observed growth processes linked to agglomeration. We

A comparison of theoretical and solar-flare intensity ratios for the Fe XIX X-ray lines

International Nuclear Information System (INIS)

Bhatia, A.K.; Mason, H.E.; Fawcett, B.C.; Phillips, K.J.H.

1989-04-01

Atomic data consisting of energy levels, g f-values and wavelengths are presented for the Fe XIX 2s 2 2p 4 -2s 2 2p 3 3s, 2s 2 2p 3 3d arrays that give rise to lines in solar flare and active-region X-ray spectra. Collision strengths and theoretical intensity ratios are given for the 2s 2 2p 4 -2s 2 2p 3 3d lines, which occur in the 13.2-14.3 A range. Solar spectra in this range include a large number of other intense lines, notably those due to He-like Ne (Ne IX). Although the Ne IX lines are potentially the most useful indicators of electron density in solar X-ray spectra, blending with the Fe XIX lines has been a major problem for previous analyses. Comparison of observed spectra with those calculated from the Fe XIX atomic data presented here and Ne IX lines from other work indicates that there is generally good agreement. We use the calculated Fe XIX and Ne IX line spectra and several observed spectra during a flare previously analysed to estimate electron density from Ne IX line ratios, thus for the first time properly taking into account blends with Fe XIX lines. (author)

Beam line to S155

CERN Multimedia

1977-01-01

The experiment S155 was designed by the Orsay (CSNM-CNRS) Collaboration to observe the properties of exotic light nuclei. It was installed in the PS neutrino tunnel. The photo shows a mass spectrometer (in the background) on line with the PS proton beam which arrives (bottom, right) from the fast extraction FE74. Roger Fergeau stands on the left. The alkaline isotopes produced in the carbon-uranium target heated at 2000°C were swiftly extracted, mass separated, and brought to a detector behind the shielding. Sodium 34 (11 protons and 23 neutrons) was observed and its half-life of only 5 ms was measured. The excited levels 2+ of Magnesium 30 and Magnesium 32 (Sodium descendants) were localised, and the magic number 20 was found to vanish. Thus, the discovery made earlier for Sodium 30 and Sodium 32, with the same apparatus, was confirmed. (See also photo 7706511.)

Design of Chebychev’s Low Pass Filters Using Nonuniform Transmission Lines

Directory of Open Access Journals (Sweden)

Said Attamimi

2016-03-01

Full Text Available Transmission lines are utilized in many applications to convey energy as well as information. Nonuniform transmission lines (NTLs are obtained through variation of the characteristic quantities along the axial direction. Such NTLs can be used to design network elements, like matching circuits, delay equalizers, filters, VLSI interconnections, etc. In this work, NTLs were analyzed with a numerical method based on the implementation of method of moment. In order to approximate the voltage and current distribution along the transmission line, a sum of basis functions with unknown amplitudes was introduced. As basis function, a constant function was used. In this work, we observed several cases such as lossless and lossy uniform transmission lines with matching and arbitrary load. These cases verified the algorithm developed in this work. The second example consists of nonuniform transmission lines in the form of abruptly changing transmission lines. This structure was used to design a Chebychev’s low pass filter. The calculated reflection and transmission factors of the filters showed some coincidences with the measurements.

Application of reliability based design concepts to transmission line structure foundations. Part 2

International Nuclear Information System (INIS)

DiGioia, A.M. Jr.; Rojas-Gonzalez, L.F.

1991-01-01

The application of reliability based design (RBD) methods to transmission line structure foundations has developed somewhat more slowly than that for the other structural components in line systems. In a previous paper, a procedure was proposed for the design of transmission line structures foundations using a probability based load and resistance factor design (LRFD) format. This procedure involved the determination of a foundation strength factor, φ F , which was used as a multiplier of the calculated nominal design strength to estimate the five percent exclusion limit strength required in the calculated nominal design strength to estimate the five percent exclusion limit strength required in the LRFD equation. Statistical analyses of results from full-scale load tests were used to obtain φ F values applicable to various nominal design strength equations and for drilled shafts subjected to uplift loads. These results clearly illustrated the significant economic benefits of conducting more detailed subsurface investigations for the design of transmission line structure foundations. A design example was also presented. In this paper the proposed procedure is extended to laterally load drilled shafts

A sampling study on rock properties affecting drilling rate index (DRI)

Science.gov (United States)

Yenice, Hayati; Özdoğan, Mehmet V.; Özfırat, M. Kemal

2018-05-01

Drilling rate index (DRI) developed in Norway is a very useful index in determining the drillability of rocks and even in performance prediction of hard rock TBMs and it requires special laboratory test equipment. Drillability is one of the most important subjects in rock excavation. However, determining drillability index from physical and mechanical properties of rocks is very important for practicing engineers such as underground excavation, drilling operations in open pit mining, underground mining and natural stone production. That is why many researchers have studied concerned with drillability to find the correlations between drilling rate index (DRI) and penetration rate, influence of geological properties on drillability prediction in tunneling, correlations between rock properties and drillability. In this study, the relationships between drilling rate index (DRI) and some physico-mechanical properties (Density, Shore hardness, uniaxial compressive strength (UCS, σc), Indirect tensile strength (ITS, σt)) of three different rock groups including magmatic, sedimentary and metamorphic were evaluated using both simple and multiple regression analysis. This study reveals the effects of rock properties on DRI according to different types of rocks. In simple regression, quite high correlations were found between DRI and uniaxial compressive strength (UCS) and also between DRI and indirect tensile strength (ITS) values. Multiple regression analyses revealed even higher correlations when compared to simple regression. Especially, UCS, ITS, Shore hardness (SH) and the interactions between them were found to be very effective on DRI values.

Event Index - a LHCb Event Search System

CERN Document Server

INSPIRE-00392208; Kazeev, Nikita; Redkin, Artem

2015-12-23

LHC experiments generate up to $10^{12}$ events per year. This paper describes Event Index - an event search system. Event Index's primary function is quickly selecting subsets of events from a combination of conditions, such as the estimated decay channel or stripping lines output. Event Index is essentially Apache Lucene optimized for read-only indexes distributed over independent shards on independent nodes.

ANTHROPOMETRIC, GAIT AND STRENGTH CHARACTERISTICS OF KENYAN DISTANCE RUNNERS

Directory of Open Access Journals (Sweden)

Pui W. Kong

2008-12-01

Full Text Available This study intended to take a biomechanical approach to understand the success of Kenyan distance runners. Anthropometric, gait and lower extremity strength characteristics of six elite Kenyan distance runners were analyzed. Stride frequency, relative stride length and ground contact time were measured at five running speeds (3.5 - 5.4 m/s using a motion capture system. Isometric knee extension and flexion torques were measured at six angles and hamstrings and quadriceps (H:Q ratios at three angular velocities were determined using an isokinetic dynamometer. These runners were characterized by a low body mass index (20.1 ± 1.8 kg·m- 2, low percentage body fat (5.1 ± 1.6% and small calf circumference (34.5 ± 2.3 cm. At all running speeds, the ground contact time was shorter (p < 0.05 during right (170 - 212 ms compared to left (177 - 220 ms foot contacts. No bilateral difference was observed in other gait or strength variables. Their maximal isometric strength was lower than other runners (knee extension: 1.4 - 2.6 Nm·kg-1, knee flexion: 1.0 - 1.4 Nm·kg-1 but their H:Q ratios were higher than athletes in other sports (1.03 ± 0.51 at 60o/s, 1.44 ± 0.46 at 120o/s, 1.59 ± 0.66 at 180o/s. The slim limbs of Kenyan distance runners may positively contribute to performance by having a low moment of inertia and thus requiring less muscular effort in leg swing. The short ground contact time observed may be related to good running economy since there is less time for the braking force to decelerate forward motion of the body. These runners displayed minor gait asymmetry, though the difference may be too small to be practically significant. Further investigations are needed to confirm whether the bilateral symmetry in strength and high H:Q ratios are related to genetics, training or the lack of injuries in these runners

Effect of deep stripping massage alone or with eccentric resistance on hamstring length and strength.

Science.gov (United States)

Forman, Jeffrey; Geertsen, Lisbeth; Rogers, Michael E

2014-01-01

Many studies have evaluated the effects of different interventions on hamstring length. However, little research has been conducted on the effects of deep stripping massage strokes (DSMS) alone, or combined with eccentric resistance, on hamstring length and strength. To determine: 1) if DSMS have an effect on hamstring length and strength and 2) if the effects on hamstring length and strength are any different when DSMS are combined with eccentric exercise. 89 Community College students and community members between the ages of 18 and 62 volunteered for the study. Of these, 64 demonstrated tight hamstrings on either one or both sides as defined by supine, passive terminal knee extension of ≤75° and participated in the study. Strength was assessed by pressing the posterior calcaneus into a strain gauge for approximately 5 s while seated with the knee flexed to 90°. On their tighter side, participants were administered longitudinal DSMS during 15, 10-s bouts of eccentric resistance with an elastic resistance band. On their other hamstring, participants were administered 15, 10-s longitudinal DSMS while lying passive. All massage strokes were performed at a depth of 7 out of 10 on a verbal pressure scale index. Afterwards, the hamstring flexibility and strength tests were repeated. Both DSMS with eccentric resistance (10.7%) and DSMS alone (6.3%) resulted in improved (p alone. Strength was not significantly affected by either treatment. These results suggest that DSMS increases hamstring length in less than 3 min but has no affect on strength. Furthermore, combining DSMS with eccentric resistance produces more hamstring flexibility gains than DSMS alone and does not affect strength. Copyright © 2013 Elsevier Ltd. All rights reserved.

Accuracy of Body Mass Index Versus Lean Mass Index for Prediction of Sarcopenia in Older Women.

Science.gov (United States)

Benton, M J; Silva-Smith, A L

2018-01-01

We compared accuracy of body mass index (BMI) versus lean mass index (LMI) to predict sarcopenia in 58 community-dwelling women (74.1±0.9 years). Lean mass was measured with multi-frequency bioelectrical impedance analysis, and strength was measured with Arm Curl test, Chair Stand test, and handgrip dynamometry. Sarcopenia was defined as low LMI. When categorized by BMI, normal women had less absolute lean mass (37.6±1.0 vs. 42.6±0.9 kg; Plean mass (14.1±0.2 vs. 16.1±0.2 kg/m2; Plean mass (44.0±0.7 vs. 35.7±0.7 kg; Plean mass (16.2±0.2 vs. 13.8±0.2 kg/m2; Plean mass and strength. For clinical assessment, calculation of LMI rather than BMI is appropriate.

Adult bone strength of children from single-parent families: the Midlife in the United States Study.

Science.gov (United States)

Crandall, C J; Karlamangla, A S; Merkin, S S; Binkley, N; Carr, D; Greendale, G A; Seeman, T E

2015-03-01

Bone health may be negatively impacted by childhood socio-environmental circumstances. We examined the independent associations of single-parent childhood and parental death or divorce in childhood with adult bone strength indices. Longer exposure to a single-parent household in childhood was associated with lower bone strength in adulthood. Because peak bone mass is acquired during childhood, bone health may be negatively impacted by childhood socio-environmental disadvantage. The goal of this study was to determine whether being raised in a single-parent household is associated with lower bone strength in adulthood. Using dual-energy X-ray absorptiometry data from 708 participants (mean age 57 years) in the Midlife in the United States Biomarker Project, we examined the independent associations of composite indices of femoral neck bone strength relative to load (in three failure modes: compression, bending, and impact) in adulthood with the experience of single-parent childhood and parental death or divorce in childhood. After adjustment for gender, race, menopause transition stage, age, and body mass index, each additional year of single-parent childhood was associated with 0.02 to 0.03 SD lower indices of adult femoral neck strength. In those with 9-16 years of single-parent childhood, the compression strength index was 0.41 SD lower, bending strength index was 0.31 SD lower, and impact strength index was 0.25 SD lower (all p values divorce during childhood was not by itself independently associated with adult bone strength indices. The magnitudes of these associations were unaltered by additional adjustment for lifestyle factors and socioeconomic status in childhood and adulthood. Independent of parental death or divorce, growing up in a single-parent household is associated with lower femoral neck bone strength in adulthood, and this association is not entirely explained by childhood or adult socioeconomic conditions or lifestyle choices.

Meniscal Tear Film Fluid Dynamics Near Marx’s Line

KAUST Repository

Zubkov, V. S.

2013-07-03

Extensive studies have explored the dynamics of the ocular surface fluid, though theoretical investigations are typically limited to the use of the lubrication approximation, which is not guaranteed to be uniformly valid a-priori throughout the tear meniscus. However, resolving tear film behaviour within the meniscus and especially its apices is required to characterise the flow dynamics where the tear film is especially thin, and thus most susceptible to evaporatively induced hyperosmolarity and subsequent epithelial damage. Hence, we have explored the accuracy of the standard lubrication approximation for the tear film by explicit comparisons with the 2D Navier-Stokes model, considering both stationary and moving eyelids. Our results demonstrate that the lubrication model is qualitatively accurate except in the vicinity of the eyelids. In particular, and in contrast to lubrication theory, the solution of the full Navier-Stokes equations predict a distinct absence of fluid flow, and thus convective mixing in the region adjacent to the tear film contact line. These observations not only support emergent hypotheses concerning the formation of Marx\\'s line, a region of epithelial cell staining adjacent to the contact line on the eyelid, but also enhance our understanding of the pathophysiological consequences of the flow profile near the tear film contact line. © 2013 Society for Mathematical Biology.

Biomechanical rupture risk assessment of abdominal aortic aneurysms based on a novel probabilistic rupture risk index.

Science.gov (United States)

Polzer, Stanislav; Gasser, T Christian

2015-12-06

A rupture risk assessment is critical to the clinical treatment of abdominal aortic aneurysm (AAA) patients. The biomechanical AAA rupture risk assessment quantitatively integrates many known AAA rupture risk factors but the variability of risk predictions due to model input uncertainties remains a challenging limitation. This study derives a probabilistic rupture risk index (PRRI). Specifically, the uncertainties in AAA wall thickness and wall strength were considered, and wall stress was predicted with a state-of-the-art deterministic biomechanical model. The discriminative power of PRRI was tested in a diameter-matched cohort of ruptured (n = 7) and intact (n = 7) AAAs and compared to alternative risk assessment methods. Computed PRRI at 1.5 mean arterial pressure was significantly (p = 0.041) higher in ruptured AAAs (20.21(s.d. 14.15%)) than in intact AAAs (3.71(s.d. 5.77)%). PRRI showed a high sensitivity and specificity (discriminative power of 0.837) to discriminate between ruptured and intact AAA cases. The underlying statistical representation of stochastic data of wall thickness, wall strength and peak wall stress had only negligible effects on PRRI computations. Uncertainties in AAA wall stress predictions, the wide range of reported wall strength and the stochastic nature of failure motivate a probabilistic rupture risk assessment. Advanced AAA biomechanical modelling paired with a probabilistic rupture index definition as known from engineering risk assessment seems to be superior to a purely deterministic approach. © 2015 The Author(s).

Normative data for hand grip strength and key pinch strength, stratified by age and gender for a multiethnic Asian population.

Science.gov (United States)

Lam, Ngee Wei; Goh, Hui Ting; Kamaruzzaman, Shahrul Bahyah; Chin, Ai-Vyrn; Poi, Philip Jun Hua; Tan, Maw Pin

2016-10-01

Hand strength is a good indicator of physical fitness and frailty among the elderly. However, there are no published hand strength references for Malaysians aged > 65 years. This study aimed to establish normative data for hand grip strength (HGS) and key pinch strength (KPS) for Malaysians aged ≥ 60 years, and explore the relationship between hand strength and physical ability. Healthy participants aged ≥ 60 years with no neurological conditions were recruited from rural and urban locations in Malaysia. HGS and KPS were measured using hand grip and key pinch dynamometers. Basic demographic data, anthropometric measures, modified Barthel Index scores and results of the Functional Reach Test (FRT), Timed Up and Go (TUG) test and Jebsen-Taylor Hand Function Test (JTHFT) were recorded. 362 subjects aged 60-93 years were recruited. The men were significantly stronger than the women in both HGS and KPS (p Malaysia. Future studies are required to determine the modifiable factors for poor hand strength. Copyright: © Singapore Medical Association

Electronic and magnetic properties of MoS2 nanoribbons with sulfur line vacancy defects

International Nuclear Information System (INIS)

Han, Yang; Zhou, Jian; Dong, Jinming

2015-01-01

Highlights: • We performed DFT calculations on Sulfur line defects embedded MoS 2 . • The defects induced bond strains are larger in the zigzag (ZZ) edge ones. • The ZZ ones are metals, having two degenerate ground states FM and AFM. • The armchair ones are nonmagnetic semiconductors. • The defects can induce some defect states in the electronic structures. - Abstract: Motivated by the recent experimental result that single sulfur vacancies in monolayer MoS 2 are mobile under the electron beam and easily agglomerate into the sulfur line vacancy defects [Physical Review B 88, 035301(2013)] , the structural, electronic and magnetic properties of one dimensional zigzag (ZZ) and armchair (AC) edge MoS 2 nanoribbons with single or double staggered sulfur line vacancy defects (hereafter, abbreviated as SV or DV, respectively), parallel to their edges, have been investigated systematically by density functional theory calculations. It is very interesting to find that the bond strains induced by the sulfur line vacancy defect can cause a much larger out-of plane distortions in the ZZ edge MoS 2 nanoribbon than in the AC edge counterpart. Besides, the defective ZZ edge MoS 2 nanoribbons with SV or DV are both metals, having their two respective degenerate ground states with the same energy, among which one is ferromagnetic (FM “ + +”) and the other is antiferromagnetic (AFM “ + −”). But the AC edge MoS 2 nanoribbons with SV or DV are both nonmagnetic semiconductors, having very different gap values. Finally, the sulfur line vacancy defects would induce some defect states in the electronic structures of the defective MoS 2 nanoribbons. All these important results could provide a new route of tuning the electronic properties of MoS 2 nanoribbons and its derivatives for their promising applications in nanoelectronics and optoelectronics

Oscillator strengths and branching fractions of 4d75p-4d75s Rh II transitions

Science.gov (United States)

Bouazza, Safa

2017-01-01

This work reports semi-empirical determination of oscillator strengths, transition probabilities and branching fractions for Rh II 4d75p-4d75s transitions in a wide wavelength range. The angular coefficients of the transition matrix, beforehand obtained in pure SL coupling with help of Racah algebra are transformed into intermediate coupling using eigenvector amplitudes of these two configuration levels determined for this purpose; The transition integral was treated as free parameter in the least squares fit to experimental oscillator strength (gf) values found in literature. The extracted value: 5s|r1|4d75p> =2.7426 ± 0.0007 is slightly smaller than that computed by means of ab-initio method. Subsequently to oscillator strength evaluations, transition probabilities and branching fractions were deduced and compared to those obtained experimentally or through another approach like pseudo-relativistic Hartree-Fock model including core-polarization effects.

Designing and Evaluating Patient Education Pamphlets based on Readability Indexes and Comparison with Literacy Levels of Society

Directory of Open Access Journals (Sweden)

Mahdieh Arian

2016-07-01

Full Text Available Background: Hundreds of patient education materials i.e. pamphlets are annually published in healthcare systems following their design, correction, and revision. Aim: to design and evaluate patient education pamphlets based on readability indexes and their comparison with literacy level in society. Method: The average literacy level among 500 patients admitted to two training hospitals in Bojnurd (northeastern Iran was determined in 2014-2015. Afterwards, all patient education pamphlets in both hospitals (n=69 were collected and their readability level was determined. After that, all the pamphlets were re-designed according to the given standards and in line with literacy level in society. The SPSS software (Version 20 was also used to analyze the data. Results: The average level of literacy among 500 patients in both hospitals in the present study was 6.72±4.34 which was placed in grades six and seven in terms of the guide to readability indexes. In line with McLaughlin’s SMOG Readability Formula, the bulk of pamphlets (91.3% were at college level before corrections and revisions based on the given standards, but 23.2% were at a level lower than grade seven following corrections and revisions. Implications for Practice: Evaluation of patient education pamphlets plays an important role in promoting self-care among patients. Due to the novelty of the present study in Iran, the results of this study can contribute to patient education researchers in order to identify the strengths and weaknesses of patient education materials i.e. pamphlets based on scientific indices as well as their revisions and re-developments.

Optical Variability of Narrow-line and Broad-line Seyfert 1 Galaxies

Science.gov (United States)

Rakshit, Suvendu; Stalin, C. S.

2017-06-01

We studied the optical variability (OV) of a large sample of narrow-line Seyfert 1 (NLSy1) and broad-line Seyfert 1 (BLSy1) galaxies with z anti-correlated with Fe II strength but correlated with the width of the Hβ line. The well-known anti-correlation of variability-luminosity and the variability-Eddington ratio is present in our data. Among the radio-loud sample, variability amplitude is found to be correlated with radio-loudness and radio-power, suggesting that jets also play an important role in the OV in radio-loud objects, in addition to the Eddington ratio, which is the main driving factor of OV in radio-quiet sources.

NLTE masking and the Kiev Fe I oscillator strengths

International Nuclear Information System (INIS)

Rutten, R.J.

1983-01-01

This contribution serves to advertise the empirical solar-spectrum determinations of the oscillator strengths of 860 Fe I lines by Gurtovenko and Kostik (1981), by showing that these Kiev data contain just the lines needed in cool-star abundance analyses, and by explaining why they are so good. (Auth.)

PLASMA DIAGNOSTIC POTENTIAL OF 2p4f IN N{sup +}—ACCURATE WAVELENGTHS AND OSCILLATOR STRENGTHS

Energy Technology Data Exchange (ETDEWEB)

Shen, Xiaozhi [School of Physics Science and Nuclear Energy Engineering, Beihang University, Beijing 100191 (China); Li, Jiguang; Wang, Jianguo [Data Center for High Energy Density Physics, Institute of Applied Physics and Computational Mathematics, P.O. Box 8009, Beijing 100088 (China); Jönsson, Per, E-mail: Li_Jiguang@iapcm.ac.cn [Materials Science and Applied Mathematics, Malmö University, SE-20506 Malmö (Sweden)

2015-03-10

Radiative emission lines from nitrogen and its ions are often observed in nebula spectra, where the N{sup 2+} abundance can be inferred from lines of the 2p4f configuration. In addition, intensity ratios between lines of the 2p3p-2p3s and 2p4f-2p3d transition arrays can serve as temperature diagnostics. To aid abundance determinations and plasma diagnostics, wavelengths and oscillator strengths were calculated with high precision for electric dipole (E1) transitions from levels in the 2p4f configuration of N{sup +}. Electron correlation and relativistic effects, including the Breit interaction, were systematically taken into account within the framework of the multiconfiguration Dirac-Hartree-Fock method. Except for the 2p4f-2p4d transitions with quite large wavelengths and the two-electron-one-photon 2p4f-2s2p {sup 3} transitions, the uncertainties of the present calculations were controlled to within 3% and 5% for wavelengths and oscillator strengths, respectively. We also compared our results with other theoretical and experimental values when available. Discrepancies were found between our calculations and previous calculations due to the neglect of relativistic effects in the latter.

The Effects of Forest Area Changes on Extreme Temperature Indexes between the 1900s and 2010s in Heilongjiang Province, China

Directory of Open Access Journals (Sweden)

Lijuan Zhang

2017-12-01

Full Text Available Land use and land cover changes (LUCC are thought to be amongst the most important impacts exerted by humans on climate. However, relatively little research has been carried out so far on the effects of LUCC on extreme climate change other than on regional temperatures and precipitation. In this paper, we apply a regional weather research and forecasting (WRF climate model using LUCC data from Heilongjiang Province, that was collected between the 1900s and 2010s, to explore how changes in forest cover influence extreme temperature indexes. Our selection of extreme high, low, and daily temperature indexes for analysis in this study enables the calculation of a five-year numerical integration trail with changing forest space. Results indicate that the total forested area of Heilongjiang Province decreased by 28% between the 1900s and 2010s. This decrease is most marked in the western, southwestern, and northeastern parts of the province. Our results also reveal a remarkable correlation between change in forested area and extreme high and low temperature indexes. Further analysis enabled us to determine that the key factor explaining increases in extreme high temperature indexes (i.e., calculated using the number of warm days, warm nights, as well as tropical nights, and summer days is decreasing forest area; data also showed that this factor caused a decrease in extreme low temperature indexes (i.e., calculated using the number of cold days and cold nights, as well as frost days, and ice days and an increase in the maximum value of daily minimum temperature. Spatial data demonstrated that there is a significant correlation between forest-to-farmland conversion and extreme temperature indexes throughout most of our study period. Spatial data demonstrated that there is a significant correlation between forest-to-farmland conversion and extreme temperature indexes throughout most of our study period. Positive correlations are also present between

Florida creativity index scores, conservatism, and openness in 268 U.S. regions.

Science.gov (United States)

McCann, Stewart J H

2011-02-01

This study assessed whether Florida's Creativity Index (2002) scores for 268 U.S. regions were related to levels of conservatism and openness in the states in which the regions were situated. State conservatism was measured as the percentage voting for Bush in 2000. State openness z scores were taken from a survey of 619,397 residents (Rentfrow, Gosling, & Potter, 2008). Creativity scores correlated negatively with conservatism (r = -.22) and positively with openness (r = .23). Regression showed that the two predictors accounted jointly (7%) and separately for significant variance in the Creativity Index. The findings contribute evidence for the construct validity of Florida's composite Creativity Index and some, albeit moderate to weak, support of the Rentfrow, et al. conclusion that state-aggregated openness reflects the unconventionality, tolerance, and creativity of a state.

Evaluation of the Fourier Frequency Spectrum Peaks of Milk Electrical Conductivity Signals as Indexes to Monitor the Dairy Goats’ Health Status by On-Line Sensors

Science.gov (United States)

Zaninelli, Mauro; Agazzi, Alessandro; Costa, Annamaria; Tangorra, Francesco Maria; Rossi, Luciana; Savoini, Giovanni

2015-01-01

The aim of this study is a further characterization of the electrical conductivity (EC) signal of goat milk, acquired on-line by EC sensors, to identify new indexes representative of the EC variations that can be observed during milking, when considering not healthy (NH) glands. Two foremilk gland samples from 42 Saanen goats, were collected for three consecutive weeks and for three different lactation stages (LS: 0–60 Days In Milking (DIM); 61–120 DIM; 121–180 DIM), for a total amount of 1512 samples. Bacteriological analyses and somatic cells counts (SCC) were used to define the health status of the glands. With negative bacteriological analyses and SCC 1,000,000 cells/mL, glands were classified as NH. For each milk EC signal, acquired on-line and for each gland considered, the Fourier frequency spectrum of the signal was calculated and three representative frequency peaks were identified. To evaluate data acquired a MIXED procedure was used considering the HS, LS and LS × HS as explanatory variables in the statistical model.Results showed that the studied frequency peaks had a significant relationship with the gland’s health status. Results also explained how the milk EC signals’ pattern change in case of NH glands. In fact, it is characterized by slower fluctuations (due to the lower frequencies of the peaks) and by an irregular trend (due to the higher amplitudes of all the main frequency peaks). Therefore, these frequency peaks could be used as new indexes to improve the performances of algorithms based on multivariate models which evaluate the health status of dairy goats through the use of gland milk EC sensors. PMID:26307993

The strength study of the rotating device driver indexing spatial mechanism

Science.gov (United States)

Zakharenkov, N. V.; Kvasov, I. N.

2018-04-01

The indexing spatial mechanisms are widely used in automatic machines. The mechanisms maximum load-bearing capacity measurement is possible based on both the physical and numerical models tests results. The paper deals with the driven disk indexing spatial cam mechanism numerical model at the constant angular cam velocity. The presented mechanism kinematics and geometry parameters and finite element model are analyzed in the SolidWorks design environment. The calculation initial data and missing parameters having been found from the structure analysis were identified. The structure and kinematics analysis revealed the mechanism failures possible reasons. The numerical calculations results showing the structure performance at the contact and bending stresses are represented.

Photoionization-driven Absorption-line Variability in Balmer Absorption Line Quasar LBQS 1206+1052

Energy Technology Data Exchange (ETDEWEB)

Sun, Luming; Zhou, Hongyan; Ji, Tuo; Jiang, Peng; Liu, Bo; Pan, Xiang; Shi, Xiheng; Zhang, Shaohua [Polar Research Institute of China, 451 Jinqiao Road, Shanghai (China); Liu, Wenjuan; Wang, Jianguo [Yunnan Observatories, Chinese Academy of Sciences, Kunming, Yunnan (China); Wang, Tinggui; Yang, Chenwei [Department of Astronomy, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui (China); Miller, Lauren P., E-mail: lmsun@mail.ustc.edu.cn [Lehigh University, 27 Memorial Drive West, Bethlehem, PA 18015 (United States)

2017-04-01

In this paper we present an analysis of absorption-line variability in mini-BAL quasar LBQS 1206+1052. The Sloan Digital Sky Survey spectrum demonstrates that the absorption troughs can be divided into two components of blueshift velocities of ∼700 and ∼1400 km s{sup −1} relative to the quasar rest frame. The former component shows rare Balmer absorption, which is an indicator of high-density absorbing gas; thus, the quasar is worth follow-up spectroscopic observations. Our follow-up optical and near-infrared spectra using MMT, YFOSC, TSpec, and DBSP reveal that the strengths of the absorption lines vary for both components, while the velocities do not change. We reproduce all of the spectral data by assuming that only the ionization state of the absorbing gas is variable and that all other physical properties are invariable. The variation of ionization is consistent with the variation of optical continuum from the V -band light curve. Additionally, we cannot interpret the data by assuming that the variability is due to a movement of the absorbing gas. Therefore, our analysis strongly indicates that the absorption-line variability in LBQS 1206+1052 is photoionization driven. As shown from photoionization simulations, the absorbing gas with blueshift velocity of ∼700 km s{sup −1} has a density in the range of 10{sup 9} to 10{sup 10} cm{sup −3} and a distance of ∼1 pc, and the gas with blueshift velocity of ∼1400 km s{sup −1} has a density of 10{sup 3} cm{sup −3} and a distance of ∼1 kpc.

An integration of competing accounts on children’s number line estimation

Directory of Open Access Journals (Sweden)

Tanja eDackermann

2015-07-01

Full Text Available Children’s estimation patterns in bounded number line estimation reveal marked developmental changes. Three different theoretical accounts were proposed to explain these changes: a log-to-linear shift account, a proportion-judgment account and a two-linear account considering familiarity with numbers or the understanding of the place-value structure of the Arabic number system. However, only the first two accounts are considered prominently in the ongoing scientific debate. Therefore, we first present a reanalysis of number line estimation data of Austrian first-graders contrasting all three accounts. Results indicate that the two-linear account is a reliable alternative to the log-to-linear shift as well as the proportion-judgment account. However, we do not claim the two-liner account to provide an exhaustive explanation for the observed developmental changes. We rather introduce the idea that aspects of all three accounts may complement - instead of exclude - each other. Jointly considering conceptual (i.e., familiarity, place-value and procedural (i.e., proportion-judgments aspects will allow for a more comprehensive understanding of children’s development in number line estimation.

Evaluation of Hose in Hose Transfer Line Service Life for Hanford's Interim Stabilization Program

Energy Technology Data Exchange (ETDEWEB)

TORRES, T.D.

2000-08-24

RPP-6153, Engineering Task Plan for Hose-in-Hose Transfer System for the Interim Stabilization Program, defines the programmatic goals, functional requirements, and technical criteria for the development and subsequent installation of transfer line equipment to support Hanford's Interim Stabilization Program. RPP-6028, Specification for Hose in Hose Transfer Lines for Hanford's Interim Stabilization Program, has been issued to define the specific requirements for the design, manufacture, and verification of transfer line assemblies for specific waste transfer applications. Included in RPP-6028 are tables defining the chemical constituents of concern to which transfer lines will be exposed. Current Interim Stabilization Program planning forecasts that the at-grade transfer lines will be required to convey pumpable waste for as much as three years after commissioning. Prudent engineering dictates that the equipment placed in service have a working life in excess of this forecasted time period, with some margin to allow for future adjustments to the planned schedule. This document evaluates the effective service life of the Hose-in-Hose Transfer Lines, based on information submitted by the manufacturer and published literature. The effective service life of transfer line assemblies is a function of several factors. Foremost among these are process fluid characteristics, ambient environmental conditions, and the manufacturer's stated shelf life. This evaluation examines the manufacturer's certification of shelf life, the manufacturer's certifications of chemical compatibility with waste, and published literature on the effects of exposure to ionizing radiation on the mechanical properties of elastomeric materials to evaluate transfer line service life.

Tensile strength and durability characteristics of high-performance fiber reinforced concrete

International Nuclear Information System (INIS)

Ramadoss, P.; Nagamani, K.

2008-01-01

This paper presents investigations towards developing a better understanding of the contribution of steel fibers to the tensile strength of high-performance fiber reinforced concrete (HPFRC). For 32 series of mixes, flexural and splitting tensile strengths were determined at 28 days. The variables investigated were fiber volume fraction (0%, 0.5%, 1% and 1.5% with an aspect of 80), silica fume replacement level (SF/CM=0.05 and 0.10) and matrix composition (w/cm ratios ranging from 0.25 t 0.40). The influence of fiber content in terms of fiber reinforcing index on the flexural and splitting tensile strengths of HPFRC is presented. Comparative studies were performed on the tensile behavior of SFRC measured by two different loading tests: flexural test and splitting test. Based on the test results, using the least square method, empirical expressions were developed to predict 28-day tensile strength of HPFRC in terms of fiber reinforcing index. Durability tests were carried out to examine the performance of the SFRC. Relationship between flexural and splitting tensile strengths has been developed using regression analysis. The experimental values of previous researchers were compared with the values predicted by the empirical equations and the absolute variation obtained was within 6% and 5% for flexural and splitting tensile strengths respectively. (author)

CI+MBPT calculations of Ar I energies, g factors, and transition line strengths

Science.gov (United States)

Savukov, I. M.

2018-03-01

Excited states of noble gas atoms present certain challenges to atomic theory for several reasons: first, relativistic effects are important and LS coupling is not optimal; second, energy intervals can be quite small, leading to strong mixing of states; third, many-body perturbation theory for hole states does not converge well. Previously, some attempts were made to solve this problem, using for example the all-order coupled-cluster approach and particle-hole configuration-interaction many-body perturbation theory (CI-MBPT) with modified denominators. However, while these approaches were promising, the accuracy was still limited. In this paper, we calculate Ar I energies, g factors, and transition amplitudes using ab initio CI-MBPT with eight valence electrons to avoid the problem of slow convergence of MBPT due to strong interaction between 3p and 3s states. We also included in CI many dominant states obtained by double excitations of the ground state configuration. Thus perturbation corrections were needed only for 1s, 2s, 2p core electrons non-included in valence-valence CI, which are quite small. We found that energy, g factors, and electric dipole matrix elements are in reasonable agreement with experiments. It is noteworthy that the theory agreed well with accurately measured g factors. Experimental oscillator strengths have large uncertainty, so in some cases we made a comparison with average values.

Maternal Employment, Work Schedules, and Children’s Body Mass Index

Science.gov (United States)

Morrissey, Taryn W.; Dunifon, Rachel E.; Kalil, Ariel

2011-01-01

Previous work has shown that mothers’ employment is associated with increases in children’s body mass index (BMI), a measure of weight-for-height. Nonstandard work (working evenings/nights, weekends, or an irregular shift) may also be associated with children’s BMI. In this paper we examine the association between maternal work and children’s BMI, and also consider the influence of mothers’ nonstandard work schedules. Using data from school-age children in the NICHD’s Study of Early Child Care and Youth Development (N = 990), we found that an increase in the total time a mother is employed is associated with an increase in her child’s BMI; additionally, we find that the association between maternal employment and children’s weight is much stronger at 6th grade relative to younger ages. There was no evidence that maternal or home characteristics or children’s time use mediated these associations, nor was there any evidence that nonstandard work was associated with children’s BMI. Implications for policy and future research are discussed. PMID:21291429

Yield and strength properties of the Ti-6-22-22S alloy over a wide strain rate and temperature range

International Nuclear Information System (INIS)

Krueger, L.; Kanel, G.I.; Razorenov, S.V.; Bezrouchko, G.S.; Meyer, L.

2002-01-01

A mechanical behavior of the Ti-6-22-22S alloy was studied under uniaxial strain conditions at shock-wave loading and under uniaxial compressive stress conditions over a strain rate range of 10-4 s-1 to 103 s-1. The test temperature was varied from -175 deg. C to 620 deg. C. The strain-rate and the temperature dependencies of the yield stress obtained from the uniaxial stress tests and from the shock-wave experiments are in a good agreement and demonstrate a significant decrease in the yield strength as the temperature increases. This indicates the thermal activation mechanism of plastic deformation of the alloy is maintained at strain rates up to 106 s-1. Variation of sample thickness from 2.24 to 10 mm results in relatively small variations in the dynamic yield strength and the spall strength over the whole temperature range

Time series analysis of S&P 500 index: A horizontal visibility graph approach

Science.gov (United States)

Vamvakaris, Michail D.; Pantelous, Athanasios A.; Zuev, Konstantin M.

2018-05-01

The behavior of stock prices has been thoroughly studied throughout the last century, and contradictory results have been reported in the corresponding literature. In this paper, a network theoretical approach is provided to investigate how crises affected the behavior of US stock prices. We analyze high frequency data from S&P500 via the Horizontal Visibility Graph method, and find that all major crises that took place worldwide in the last twenty years, affected significantly the behavior of the price-index. Nevertheless, we observe that each of those crises impacted the index in a different way and magnitude. Interestingly, our results suggest that the predictability of the price-index series increases during the periods of crises.

TIGER/Line Shapefile, 2016, nation, U.S., Military Installation National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Primary Roads National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Primary Roads National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., Primary Roads National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Current Metropolitan Division National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Current NECTA Division National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Current Metropolitan Division National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., Current NECTA Division National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., Military Installation National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Current NECTA Division National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Military Installation National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

Using the Properties of Broad Absorption Line Quasars to Illuminate Quasar Structure

Science.gov (United States)

Yong, Suk Yee; King, Anthea L.; Webster, Rachel L.; Bate, Nicholas F.; O'Dowd, Matthew J.; Labrie, Kathleen

2018-06-01

A key to understanding quasar unification paradigms is the emission properties of broad absorption line quasars (BALQs). The fact that only a small fraction of quasar spectra exhibit deep absorption troughs blueward of the broad permitted emission lines provides a crucial clue to the structure of quasar emitting regions. To learn whether it is possible to discriminate between the BALQ and non-BALQ populations given the observed spectral properties of a quasar, we employ two approaches: one based on statistical methods and the other supervised machine learning classification, applied to quasar samples from the Sloan Digital Sky Survey. The features explored include continuum and emission line properties, in particular the absolute magnitude, redshift, spectral index, line width, asymmetry, strength, and relative velocity offsets of high-ionisation C IV λ1549 and low-ionisation Mg II λ2798 lines. We consider a complete population of quasars, and assume that the statistical distributions of properties represent all angles where the quasar is viewed without obscuration. The distributions of the BALQ and non-BALQ sample properties show few significant differences. None of the observed continuum and emission line features are capable of differentiating between the two samples. Most published narrow disk-wind models are inconsistent with these observations, and an alternative disk-wind model is proposed. The key feature of the proposed model is a disk-wind filling a wide opening angle with multiple radial streams of dense clumps.

Evaluation of 99 S/sub 1/ lines of maize for inbreeding depression

International Nuclear Information System (INIS)

Ahmad, M.; Khan, S.; Ahmad, F.; Shah, N.H.; Akhtar, N.

2010-01-01

The research was conducted to evaluate the performance of S1 lines for inbreeding depression regarding different parameters, using maize variety Azam. The maize variety was self-pollinated for one generation in spring season and in the next sowing season 99 S1 lines obtained from selfing was sown with a parental line. Days to silking, pollen-shedding, plant height , ear-height, ear-length, ear-diameter, number of ears/row, kernel rows/ear and 100 kernel weight showed inbreeding depression with varying degrees while yield kg/ha showed severe inbreeding depression with an average of 362.08 kg/ha. Average value of inbreeding depression for days to silking and pollen-shedding was calculated as 2.02 and 2.21 days, respectively. Average values of inbreeding depression for plant height and ear-height were recorded as 21.50 cm and 4.87 cm, respectively. While, for earlength, ear-diameter, number of ears/row, kernel rows/ear and 100 grain weight, the average value of inbreeding depression was recorded as 1.80 cm, 0.2 cm, 2.5, 2.11 and 3.89 g, respectively. Grain yield was positively and significantly correlated with plant height, ear height and yield components. Maturity traits were positively and significantly linked with each other. It is concluded that by subjecting the maize to self-pollination nearly all the lines were affected; however, some lines were affected severely and others tolerated inbreeding to some extent. The lines showing tolerance against inbreeding depression was selected for further maize breeding. (author)

Improving Blast Resistance of a Thermo-Sensitive Genic Male Sterile Rice Line GD-8S by Molecular Marker-Assisted Selection

Directory of Open Access Journals (Sweden)

Wu-ge LIU

2008-09-01

Full Text Available The broad-spectrum blast resistance gene Pi-1, from donor line BL122, was introduced into a thermo-sensitive genic male sterile rice line GD-8S, which possessed good grain quality but high susceptibility to rice blast, by using backcross breeding and molecular marker-assisted selection. Five elite improved male sterile lines, RGD8S-1, RGD8S-2, RGD8S-3, RGD8S-4 and RGD8S-5, were selected based on the results of molecular marker analysis, spikelet sterility, recovery rate of genetic background and agronomic traits. Thirty-three representative blast isolates collected from Guangdong Province, China were used to inoculate the improved lines and the original line GD-8S artificially. The resistance frequencies of the improved lines ranged from 76.47% to 100%, much higher than that of the original line GD-8S (9.09%. On the agronomic characters, there were no significant differences between the improved lines and GD-8S except for flag leaf length and panicle number per plant. The improved lines could be used for breeding hybrid rice with high blast resistance.

The eccentric, concentric strength relationship of the hamstring muscles in chronic low back pain.

Science.gov (United States)

Marshall, Paul W M; Mannion, Jamie; Murphy, Bernadette A

2010-02-01

The objective of this study was to measure hamstring muscle eccentric and concentric strength in individuals with and without low back pain (LBP). Two composite scores for the relative balance of eccentric to concentric strength at the different movement velocities were calculated (the DEC and SEC), to determine whether or not self perceived pain, disability, or fear avoidance measures were associated with hamstring strength characteristics. Cross-sectional repeated measures design. University laboratory. Fifteen individuals with chronic LBP and 15 matched controls. Isokinetic eccentric and concentric strength at 30 degrees s(-1) and 120 degrees s(-1)(.) Composite scores (DEC and SEC) based on peak torque were calculated to evaluate the relationship between the different muscle actions across the test velocities. Self report measures included the Oswestry disability index, general health and well being, fear avoidance, and pain. Eccentric/concentric strength ratio at 30 degrees s(-1) was higher for the LBP group (F(1,58)=4.81, p=0.032). The SEC was also higher for the LBP (F(1,58)=5.97, p=0.018). Fear avoidance beliefs and mental well-being were significantly associated with the SEC only in the LBP group (adjusted r(2)=0.26, (F(2,27)=5.8, p=.008). For the control group both the DEC and SEC were associated with self report measures. Matched differences between groups' for the SEC were best explained by fear avoidance beliefs about work (adjusted r(2)=0.12, F(1,28)=5.1, p=0.03). Reduced concentric relative to eccentric strength is best identified by the SEC. The SEC was significantly associated with impaired self report measures of fear avoidance and mental well being in individuals with LBP. Differences between groups for the SEC were best explained by fear avoidance beliefs about work.

Modern high strength QT, TM and duplex-stainless steels

Energy Technology Data Exchange (ETDEWEB)

Bocquet, P. [Industeel (France); Luxenburger, G. [Aktiengesellschaft der Dillinger Huettenwerke, Dillingen/Saar (Germany); Porter, D. [Rautaruukki (Finland); Ericsson, C. [Avesta Polarit (Sweden)

2003-07-01

Pressure vessels are commonly manufactured with normalised steel grades with a yield strength up to 355 MPa or with austenitic stainless steels when corrosion as to be considered. From three decades, modern steels with higher mechanical properties - up to yield strength of 960 Mpa - are available and largely used for other applications where weight saving is of major importance as per off-shore, bridges, cranes, shipbuilding, line pipes.. The paper presents these modern steel's families - TMCP (Thermo Mechanically Controlled Process), QT (Quenched and Tempered) and Duplex (austeno-ferritic) stainless - in comparison with the normalised and austenitic steel grades. The following aspects are presented: the main mechanical properties (tensile and Charpy) as per the requirements of the standards for pressure equipment; some examples of use of these modern steels in the industry are given; the limitations of the forming conditions are considered; the weldability aspects and welds properties are developed; the interest of the PWHT (Post Weld Heat Treatment) is discussed. (orig.)

K-line photometry

International Nuclear Information System (INIS)

Henry, R.C.

1979-01-01

A brief review is given of more than a decade of work involving measurement of the strength of the K line of calcium in A-type stars. The effects of interstellar reddening are reexamined, and an improved estimate for the range in calcium abundance among field stars is obtained. (Auth.)

Reliability and relationships among handgrip strength, leg extensor strength and power, and balance in older men.

Science.gov (United States)

Jenkins, Nathaniel D M; Buckner, Samuel L; Bergstrom, Haley C; Cochrane, Kristen C; Goldsmith, Jacob A; Housh, Terry J; Johnson, Glen O; Schmidt, Richard J; Cramer, Joel T

2014-10-01

To quantify the reliability of isometric leg extension torque (LEMVC), rate of torque development (LERTD), isometric handgrip force (HGMVC) and RFD (HGRFD), isokinetic leg extension torque and power at 1.05rad·s(-1) and 3.14rad·s(-1); and explore relationships among strength, power, and balance in older men. Sixteen older men completed 3 isometric handgrips, 3 isometric leg extensions, and 3 isokinetic leg extensions at 1.05rad·s(-1) and 3.14rad·s(-1) during two visits. Intraclass correlation coefficients (ICCs), ICC confidence intervals (95% CI), coefficients of variation (CVs), and Pearson correlation coefficients were calculated. LERTD demonstrated no reliability. The CVs for LERTD and HGRFD were ≤23.26%. HGMVC wasn't related to leg extension torque or power, or balance (r=0.14-0.47; p>0.05). However, moderate to strong relationships were found among isokinetic leg extension torque at 1.05rad·s(-1) and 3.14rad·s(-1), leg extension mean power at 1.05rad·s(-1), and functional reach (r=0.51-0.95; p≤0.05). LERTD and HGRFD weren't reliable and shouldn't be used as outcome variables in older men. Handgrip strength may not be an appropriate surrogate for lower body strength, power, or balance. Instead, perhaps handgrip strength should only be used to describe upper body strength or functionality, which may compliment isokinetic assessments of lower body strength, which were reliable and related to balance. Copyright © 2014 Elsevier Inc. All rights reserved.

Optimum concrete compression strength using bio-enzyme

OpenAIRE

Bagio Tony Hartono; Basoeki Makno; Tistogondo Julistyana; Pradana Sofyan Ali

2017-01-01

To make concrete with high compressive strength and has a certain concrete specifications other than the main concrete materials are also needed concrete mix quality control and other added material is also in line with the current technology of concrete mix that produces concrete with specific characteristics. Addition of bio enzyme on five concrete mixture that will be compared with normal concrete in order to know the optimum level bio-enzyme in concrete to increase the strength of the con...

Aerobic fitness, muscular strength and obesity in relation to risk of heart failure.

Science.gov (United States)

Crump, Casey; Sundquist, Jan; Winkleby, Marilyn A; Sundquist, Kristina

2017-11-01

Low physical fitness and obesity have been associated with higher risk of developing heart failure (HF), but their interactive effects are unknown. Elucidation of interactions among these common modifiable factors may help facilitate more effective primary prevention. We conducted a national cohort study to examine the interactive effects of aerobic fitness, muscular strength and body mass index (BMI) among 1 330 610 military conscripts in Sweden during 1969-1997 (97%-98% of all 18-year-old men) on risk of HF identified from inpatient and outpatient diagnoses through 2012 (maximum age 62 years). There were 11 711 men diagnosed with HF in 37.8 million person-years of follow-up. Low aerobic fitness, low muscular strength and obesity were independently associated with higher risk of HF, after adjusting for each other, socioeconomic factors, other chronic diseases and family history of HF. The combination of low aerobic fitness and low muscular strength (lowest vs highest tertiles) was associated with a 1.7-fold risk of HF (95% CI 1.6 to 1.9; pfitness, low muscular strength and obesity at the age of 18 years were independently associated with higher risk of HF in adulthood, with interactive effects between aerobic fitness and muscular strength. These findings suggest that early-life interventions may help reduce the long-term risk of HF and should include both aerobic fitness and muscular strength, even among persons with normal BMI. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Comparison of shear bond strengths of conventional orthodontic composite and nano-ceramic restorative composite: An in vitro study

Directory of Open Access Journals (Sweden)

Namit Nagar

2013-01-01

Full Text Available Objectives: To compare the shear bond strength of a nano-ceramic restorative composite Ceram-X MonoTM♦, a restorative resin with the traditional orthodontic composite Transbond XTTM† and to evaluate the site of bond failure using Adhesive Remnant Index. Materials and Methods: Sixty extracted human premolars were divided into two groups of 30 each. Stainless steel brackets were bonded using Transbond XTTM† (Group I and Ceram-X MonoTM♦ (Group II according to manufacturer′s protocol. Shear bond strength was measured on Universal testing machine at crosshead speed of 1 mm/minute. Adhesive Remnant Index scores were assigned to debonded brackets of each group. Data was analyzed using unpaired ′t′ test and Chi square test. Results: The mean shear bond strength of Group I (Transbond XTTM† was 12.89 MPa ± 2.19 and that of Group II (Ceram-X MonoTM was 7.29 MPa ± 1.76. Unpaired ′t′ test revealed statistically significant differences amongst the shear bond strength of the samples measured. Chi-square test revealed statistically insignificant differences amongst the ARI scores of the samples measured. Conclusions: Ceram-X MonoTM♦ had a lesser mean shear bond strength when compared to Transbond XTTM† which was statistically significant difference. However, the mean shear bond of Ceram X Mono was within the clinically acceptable range for bonding. Ceram-X MonoTM† and Transbond XTTM† showed cohesive fracture of adhesive in 72.6% and 66.6% of the specimens, respectively.

An empirical model of L-band scintillation S4 index constructed by using FORMOSAT-3/COSMIC data

Science.gov (United States)

Chen, Shih-Ping; Bilitza, Dieter; Liu, Jann-Yenq; Caton, Ronald; Chang, Loren C.; Yeh, Wen-Hao

2017-09-01

Modern society relies heavily on the Global Navigation Satellite System (GNSS) technology for applications such as satellite communication, navigation, and positioning on the ground and/or aviation in the troposphere/stratosphere. However, ionospheric scintillations can severely impact GNSS systems and their related applications. In this study, a global empirical ionospheric scintillation model is constructed with S4-index data obtained by the FORMOSAT-3/COSMIC (F3/C) satellites during 2007-2014 (hereafter referred to as the F3CGS4 model). This model describes the S4-index as a function of local time, day of year, dip-latitude, and solar activity using the index PF10.7. The model reproduces the F3/C S4-index observations well, and yields good agreement with ground-based reception of satellite signals. This confirms that the constructed model can be used to forecast global L-band scintillations on the ground and in the near surface atmosphere.

Treatment of Petroleum Sludge By Using Solidification/Stabilization (S/S) Method : Effect of Hydration Days to Heavy Metals Leaching and Strength

Science.gov (United States)

Murshid, N.; Kamil, N. A. F. M.; Kadir, A. A.

2018-04-01

Petroleum sludge is one of the major solid wastes generated in the petroleum industry. Generally, there are numbers of heavy metals in petroleum sludge and one treatment that is gaining prominence to treat a variety of mixed organic and inorganic waste is solidification/stabilization (S/S) method. The treatment protects human health and the environment by immobilizing contaminants within the treated material and prevents migration of the contaminants. In this study, solidification/stabilization (S/S) method has been used to treat the petroleum sludge. The comparison of hydration days, namely, 7th and 28th days in these cement-based waste materials were studied by using Synthetic Precipitate Leaching Procedure (SPLP). The results were compared to the United States Environmental Protection Agency (USEPA) standards. The results for leaching test concluded that less percentage OPC gave maximum concentration of heavy metals leaching due to deficient in Calcium Oxide (CaO), which is can caused weak solidification in the mixture. Physical and mechanical properties conducted such as compressive strength and density test. From the results, it shows addition up to of 30percentage PS give results which comply with minimum landfill dispose limit. The results shows correlation between strength and density are strong regression coefficient of 82.7%. In conclusion, S/S method can be alternative disposal method for PS in the same time complies with standard for minimum landfill disposal limit. The results for leaching test concluded the less OPC percentage gave maximum concentration of heavy metals leaching.

Ras p21 and other Gn proteins are detected in mammalian cell lines by [gamma-35S]GTP gamma S binding

International Nuclear Information System (INIS)

Comerford, J.G.; Gibson, J.R.; Dawson, A.P.; Gibson, I.

1989-01-01

The presence of guanine nucleotide binding proteins in mouse and human cell lines was investigated using [gamma- 35 S]GTP gamma S and [gamma-32P]GTP. Cell lysate polypeptides were separated by sodium dodecyl sulphate polyacrylamide gel electrophoresis and transferred to nitrocellulose. Incubation of the nitrocellulose blots with [gamma- 35 S]GTP gamma S identified 9 distinct GTP-binding polypeptides in all lysates. One of these is the ras oncogene product, p21, as demonstrated by subsequent immunochemical staining of the nitrocellulose blots. We have shown that this procedure provides a sensitive method for detection of p21 in culture cell lines

[Strength, flexibility, balance, resistance and flexibility assessment according to body mass index in active older women].

Science.gov (United States)

Vaquero-Cristóbal, Raquel; Martínez González-Moro, Ignacio; Alacid Cárceles, Fernando; Ros Simón, Esperanza

2013-01-01

Overweight and obesity are increasing at an alarming rate among older people. This is mainly because this population is predominantly sedentary. The aim of this study was to classify, according to the body mass index (BMI), a group of older active women and to evaluate the different basic physical abilities as a function of this. The BMI and fitness were evaluated in 60 elderly active women (mean age: 66.14 ± 6.59 years) using the 2-minute step test, arm curl test, chair stand test, back scratch test, chair-sit and reach-test, flamenco test, and 8-foot up-and-go test. It was found that 52.23% of the women studied had a normal BMI and 47.76% were slightly overweight. There were no cases of obesity or underweight. Women with normal BMI had better values in all tests than overweight women. Significant differences were found in the flamenco test (P<.05), and 8-foot up-and-go test (P<.01). Older women who usually do physical activity had a normal or slightly overweight BMI. It was also found that women with lower BMI have better resistance, flexibility, balance and strength. Copyright © 2012 SEGG. Published by Elsevier Espana. All rights reserved.

Electronic and magnetic properties of MoS{sub 2} nanoribbons with sulfur line vacancy defects

Energy Technology Data Exchange (ETDEWEB)

Han, Yang [Group of Computational Condensed Matter Physics, National Laboratory of Solid State Microstructures and Department of Physics, Nanjing University, Nanjing 210093 (China); Zhou, Jian [National Laboratory of Solid State Microstructures and Department of Materials Science and Engineering, Nanjing University, Nanjing 210093 (China); Dong, Jinming, E-mail: jdong@nju.edu.cn [Group of Computational Condensed Matter Physics, National Laboratory of Solid State Microstructures and Department of Physics, Nanjing University, Nanjing 210093 (China)

2015-08-15

Highlights: • We performed DFT calculations on Sulfur line defects embedded MoS{sub 2}. • The defects induced bond strains are larger in the zigzag (ZZ) edge ones. • The ZZ ones are metals, having two degenerate ground states FM and AFM. • The armchair ones are nonmagnetic semiconductors. • The defects can induce some defect states in the electronic structures. - Abstract: Motivated by the recent experimental result that single sulfur vacancies in monolayer MoS{sub 2} are mobile under the electron beam and easily agglomerate into the sulfur line vacancy defects [Physical Review B 88, 035301(2013)] , the structural, electronic and magnetic properties of one dimensional zigzag (ZZ) and armchair (AC) edge MoS{sub 2} nanoribbons with single or double staggered sulfur line vacancy defects (hereafter, abbreviated as SV or DV, respectively), parallel to their edges, have been investigated systematically by density functional theory calculations. It is very interesting to find that the bond strains induced by the sulfur line vacancy defect can cause a much larger out-of plane distortions in the ZZ edge MoS{sub 2} nanoribbon than in the AC edge counterpart. Besides, the defective ZZ edge MoS{sub 2} nanoribbons with SV or DV are both metals, having their two respective degenerate ground states with the same energy, among which one is ferromagnetic (FM “ + +”) and the other is antiferromagnetic (AFM “ + −”). But the AC edge MoS{sub 2} nanoribbons with SV or DV are both nonmagnetic semiconductors, having very different gap values. Finally, the sulfur line vacancy defects would induce some defect states in the electronic structures of the defective MoS{sub 2} nanoribbons. All these important results could provide a new route of tuning the electronic properties of MoS{sub 2} nanoribbons and its derivatives for their promising applications in nanoelectronics and optoelectronics.

Evaluation of the Fourier Frequency Spectrum Peaks of Milk Electrical Conductivity Signals as Indexes to Monitor the Dairy Goats’ Health Status by On-Line Sensors

Directory of Open Access Journals (Sweden)

Mauro Zaninelli

2015-08-01

Full Text Available The aim of this study is a further characterization of the electrical conductivity (EC signal of goat milk, acquired on-line by EC sensors, to identify new indexes representative of the EC variations that can be observed during milking, when considering not healthy (NH glands. Two foremilk gland samples from 42 Saanen goats, were collected for three consecutive weeks and for three different lactation stages (LS: 0–60 Days In Milking (DIM; 61–120 DIM; 121–180 DIM, for a total amount of 1512 samples. Bacteriological analyses and somatic cells counts (SCC were used to define the health status of the glands. With negative bacteriological analyses and SCC < 1,000,000 cells/mL, glands were classified as healthy. When bacteriological analyses were positive or showed a SCC > 1,000,000 cells/mL, glands were classified as NH. For each milk EC signal, acquired on-line and for each gland considered, the Fourier frequency spectrum of the signal was calculated and three representative frequency peaks were identified. To evaluate data acquired a MIXED procedure was used considering the HS, LS and LS × HS as explanatory variables in the statistical model.Results showed that the studied frequency peaks had a significant relationship with the gland’s health status. Results also explained how the milk EC signals’ pattern change in case of NH glands. In fact, it is characterized by slower fluctuations (due to the lower frequencies of the peaks and by an irregular trend (due to the higher amplitudes of all the main frequency peaks. Therefore, these frequency peaks could be used as new indexes to improve the performances of algorithms based on multivariate models which evaluate the health status of dairy goats through the use of gland milk EC sensors.

A global coupling index of multivariate neural series with application to the evaluation of mild cognitive impairment.

Science.gov (United States)

Wen, Dong; Xue, Qing; Lu, Chengbiao; Guan, Xinyong; Wang, Yuping; Li, Xiaoli

2014-08-01

Recently, the synchronization between neural signals has been widely used as a key indicator of brain function. To understand comprehensively the effect of synchronization on the brain function, accurate computation of the synchronization strength among multivariate neural series from the whole brain is necessary. In this study, we proposed a method named global coupling index (GCI) to estimate the synchronization strength of multiple neural signals. First of all, performance of the GCI method was evaluated by analyzing simulated EEG signals from a multi-channel neural mass model, including the effects of the frequency band, the coupling coefficient, and the signal noise ratio. Then, the GCI method was applied to analyze the EEG signals from 12 mild cognitive impairment (MCI) subjects and 12 normal controls (NC). The results showed that GCI method had two major advantages over the global synchronization index (GSI) or S-estimator. Firstly, simulation data showed that the GCI method provided both a more robust result on the frequency band and a better performance on the coupling coefficients. Secondly, the actual EEG data demonstrated that GCI method was more sensitive in differentiating the MCI from control subjects, in terms of the global synchronization strength of neural series of specific alpha, beta1 and beta2 frequency bands. Hence, it is suggested that GCI is a better method over GSI and S-estimator to estimate the synchronization strength of multivariate neural series for predicting the MCI from the whole brain EEG recordings. Copyright © 2014. Published by Elsevier Ltd.

The degradation of lining of rotary furnaces in the production of zinc oxide

Czech Academy of Sciences Publication Activity Database

Luptáková, Natália; Pešlová, F.; Anisimov, E.

2014-01-01

Roč. 21, č. 3 (2014), s. 116-121 ISSN 1335-0803 Institutional support: RVO:68081723 Keywords : zinc oxide * the production of zinc oxide * zinc slag * refractories * the degradation of rotary furnace linings Subject RIV: JG - Metallurgy http://ojs.mateng.sk/index.php/Mateng/article/view/133/194

Generating material strength standards of aluminum alloys for research reactors. Pt. 1. Yield strength values Sy and tensile strength values Su

International Nuclear Information System (INIS)

Tsuji, H.; Miya, K.

1995-01-01

Aluminum alloys are frequently used as structural materials for research reactors. The material strength standards, however, such as the yield strength values (S y ), the tensile strength values (S u ) and the design fatigue curve -which are needed to use aluminum alloys as structural materials in ''design by analysis'' - for those materials have not been determined yet. Hence, a series of material tests was performed and the results were statistically analyzed with the aim of generating these material strength standards. This paper, the first in a series on material strength standards of aluminum alloys, describes the aspects of the tensile properties of the standards. The draft standards were compared with MITI no. 501 as well as with the ASME codes, and the trend of the available data also was examined. It was revealed that the draft proposal could be adopted as the material strength standards, and that the values of the draft standards at and above 150 C for A6061-T6 and A6063-T6 could be applied only to the reactor operating conditions III and IV. Also the draft standards have already been adopted in the Science and Technology Agency regulatory guide (standards for structural design of nuclear research plants). (orig.)

Ultraviolet photometry from the orbiting astronomical observatory. XVI - The stellar Lyman-alpha absorption line

Science.gov (United States)

Savage, B. D.; Panek, R. J.

1974-01-01

The stellar Lyman-alpha line at 1216 A was observed in 29 lightly reddened stars of spectral type B2.5 to B9 by a far-UV spectrophotometer on OAO-2. The equivalent widths obtained range from 15 A at type B2.5 to 65 A at type B8; in the late-B stars, the L-alpha line removes 2 to 3% of the total stellar flux. In this sampling, the strength of the L-alpha line correlates well with measures of the Balmer discontinuity and Balmer line strengths; luminosity classification does not seem to affect the line strength. The observed line widths also agree with the predictions of Mihala's grid of non-LTE model atmospheres. In some cases, the L-alpha line influences the interstellar column densities reported in the interstellar OAO-2 L-alpha survey. Hence, these data toward lightly reddened B2 and B1.5 stars should be regarded as upper limits only.

Smoking impact on grip strength and fatigue resistance: implications for exercise and hand therapy practice.

Science.gov (United States)

Al-Obaidi, Saud; Al-Sayegh, Nowall; Nadar, Mohammed

2014-07-01

Grip strength assessment reflects on overall health of the musculoskeletal system and is a predictor of functional prognosis and mortality. The purpose of this study was: examine whether grip-strength and fatigue resistance are impaired in smokers, determine if smoking-related impairments (fatigue-index) can be predicted by demographic data, duration of smoking, packets smoked-per-day, and physical activity. Maximum isometric grip strength (MIGS) of male smokers (n = 111) and nonsmokers (n = 66) was measured before/after induced fatigue using Jamar dynamometer at 5-handle positions. Fatigue index was calculated based on percentage change in MIGS initially and after induced fatigue. Number of repetitions to squeeze the soft rubber ball to induce fatigue was significantly lower in smokers compared with nonsmokers (t = 10.6, P smoking status on MIGS scores was significantly different between smokers and nonsmokers after induced fatigue (β = -3.98, standard error = 0.59, P Smoking status was the strongest significant independent predictor of the fatigue-index. Smokers demonstrated reduced grip strength and fast fatigability in comparison with nonsmokers.

Electron-impact excitation of Fe II: Effective collision strengths for optically allowed fine-structure transitions

International Nuclear Information System (INIS)

Ramsbottom, C.A.

2009-01-01

In this paper, we present collision strengths and Maxwellian averaged effective collision strengths for the electron-impact excitation of Fe II. We consider specifically the optically allowed lines for transitions from the 3d 6 4s and 3d 7 even parity configuration states to the 3d 6 4p odd parity configuration levels. The parallel suite of Breit-Pauli codes are utilized to compute the collision cross-sections where relativistic effects are included explicitly in both the target and the scattering approximation. A total of 100 LS or 262-jj levels formed from the basis configurations 3d 6 4s, 3d 7 and 3d 6 4p were included in the wavefunction representation of the target, including all doublet, quartet and sextet terms. The Maxwellian averaged effective collision strengths are computed across a wide range of electron temperatures from 100 to 100,000 K, temperatures of importance in astrophysical and plasma applications. A detailed comparison is made with previous works and significant differences were found to occur for some of the transitions considered. We conclude that in order to obtain converged collision strengths and effective collision strengths for these allowed transitions it is necessary to include contributions from partial waves up to L = 50 explicitly in the calculation, and in addition, account for contributions from even higher partial waves through a 'top up' procedure.

Circuit QED with hybrid metamaterial transmission lines

Energy Technology Data Exchange (ETDEWEB)

Ruloff, Stefan; Taketani, Bruno; Wilhelm, Frank [Theoretical Physics, Universitaet des Saarlandes, Saarbruecken (Germany)

2016-07-01

We're working on the theory of metamaterials providing some interesting results. The negative refraction index causes an opposite orientation of the wave vector k and the Poynting vector S of the travelling waves. Hence the metamaterial has a falling dispersion relation ∂ω(k)/∂k < 0 implying that low frequencies correspond to short wavelengths. Metamaterials are simulated by left-handed transmission lines consisting of discrete arrays of series capacitors and parallel inductors to ground. Unusual physics arises when right-and left-handed transmission lines are coupled forming a hybrid metamaterial transmission line. E.g. if a qubit is placed in front of a hybrid metamaterial transmission line terminated in an open circuit, the spontaneous emission rate is weakened or unaffected depending on the transition frequency of the qubit. Some other research interests are the general analysis of metamaterial cavities and the mode structure of hybrid metamaterial cavities for QND readout of multi-qubit operators. Especially the precise answer to the question about the definition of the mode volume of a metamaterial cavity is one of our primary goals.

Caries prevalence and DMF-T index of Papuan’s students with Betel chewing habit

Directory of Open Access Journals (Sweden)

Yohanes Tebai

2009-03-01

Full Text Available The purpose of the research is to find the extent of caries prevalence and DMF-T index in Papuan’s students with betel chewing habit in Cilaki Dormitory Bandung, 2007. Betel chewing habit is a chewing action of Areca nut (Areca Catechu Linn, Betel leaves (Piper Betel Folia, Betel fruit (Piper Betle Linn, lime talk (Calcium Hydroxide, and after chew to spent out of the mouth. The research is a descriptive research using the survey technique. Research samples are determined by purposive sampling, and a number of 80 samples are collected, consisting of Papuan’s student with betel chewing habit in Bandung between 18-to-30 years of age. Research results indicated that caries prevalence is 98.75% with a DMF-T index of 5.46. The conclusion of the reseach is that the caries prevalence and the DMF-T in Papuan’s student with betel chewing habit in Cilaki Papuan’s Student Dormitory Bandung, 2007, is in the high category.

Strength development of high-strength ductile concrete incorporating Metakaolin and PVA fibers.

Science.gov (United States)

Nuruddin, Muhammad Fadhil; Khan, Sadaqat Ullah; Shafiq, Nasir; Ayub, Tehmina

2014-01-01

The mechanical properties of high-strength ductile concrete (HSDC) have been investigated using Metakaolin (MK) as the cement replacing material and PVA fibers. Total twenty-seven (27) mixes of concrete have been examined with varying content of MK and PVA fibers. It has been found that the coarser type PVA fibers provide strengths competitive to control or higher than control. Concrete with coarser type PVA fibers has also refined microstructure, but the microstructure has been undergone with the increase in aspect ratio of fibers. The microstructure of concrete with MK has also more refined and packing of material is much better with MK. PVA fibers not only give higher stiffness but also showed the deflection hardening response. Toughness Index of HSDC reflects the improvement in flexural toughness over the plain concrete and the maximum toughness indices have been observed with 10% MK and 2% volume fraction of PVA fibers.

Effect of loading rate on hen´s eggshell mechanics

Czech Academy of Sciences Publication Activity Database

Trnka, Jan; Buchar, J.; Severa, L.; Nedomová, Š.; Stoklasová, Pavla

2012-01-01

Roč. 1, č. 4 (2012), s. 1-5 ISSN 1927-0887 Institutional research plan: CEZ:AV0Z20760514 Keywords : eggshell * strength * elasticity * numerical simulation Subject RIV: GM - Food Processing http://www.ccsenet.org/journal/index.php/jfr/article/view/19064

INFLUENCE OF STRENGTH TRAINING PROGRAM ON ISOMETRIC MUSCLE STRENGTH IN YOUNG ATHLETES

Directory of Open Access Journals (Sweden)

Dragan Radovanovic

2007-10-01

Full Text Available Strength training, or resistance training, is a form of physical conditioning used to increase the ability to resist force. Since muscular strength is required for success in many sports, it is logical to assume that stronger and more powerful young athletes will achieve better results. The aim of the study was to examine the effects of strength training on young athletes. An eight-week strength training program for developing muscle strength was performed in this study. Training protocol was designed specifically for young adolescent’s athletes. The program consisted of exercises for lower and upper body, abdominal and lower back muscles. The programs did not involve the maximal (1-3 repetitions maximum and other very hard intensity exercises that may had negative effect on young athletes. The results showed that strength training program had positive effects on maximal isometric muscle force (Fmax and motor skill. The increase presents the combined influence of strength training and growth.

Social Vulnerability Index (SoVI) for the U.S. Coastal States based on the 2010 Census Tracts

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Social Vulnerability Index (SoVI) 2006-10 measures the social vulnerability of U.S. counties to environmental hazards. The index is a comparative metric that...

The computation of dynamic fractional difference parameter for S&P500 index

Science.gov (United States)

Pei, Tan Pei; Cheong, Chin Wen; Galagedera, Don U. A.

2015-10-01

This study evaluates the time-varying long memory behaviors of the S&P500 volatility index using dynamic fractional difference parameters. Time-varying fractional difference parameter shows the dynamic of long memory in volatility series for the pre and post subprime mortgage crisis triggered by U.S. The results find an increasing trend in the S&P500 long memory volatility for the pre-crisis period. However, the onset of Lehman Brothers event reduces the predictability of volatility series following by a slight fluctuation of the factional differencing parameters. After that, the U.S. financial market becomes more informationally efficient and follows a non-stationary random process.

The recommendation of line-balancing improvement on MCM product line 1 using genetics algorithm and moodie young at XYZ Company, Co.

Science.gov (United States)

Sriwana, I. K.; Marie, I. A.; Mangala, D.

2017-12-01

Kencana Gemilang, Co. is one electronics industry engaging in the manufacture sector. This company manufactures and assembles household electronic products, such as rice cooker, fan, iron, blender, etc. The company deals with an issue of underachievement of an established production target on MCM products line 1. This study aimed to calculate line efficiencies, delay times, and initial line smoothness indexes. The research was carried out by means of depicting a precedence diagram and gathering time data of each work element followed by examination and calculation of standard time as well as line balancing using methods of Moodie Young and Generics Algorithm. Based on results of calculation, better line balancing than the existing initial conditions, i.e. improvement in the line efficiency by 18.39%, deterioration in balanced delay by 28.39%, and deterioration of a smoothness index by 23.85% was obtained.

BAYESZ, S-Wave, P-Wave Resonance Level Spacing and Strength Functions

International Nuclear Information System (INIS)

Moore, M.S.

1982-01-01

A - Description of problem or function: BAYESZ calculates average s- and p-wave level spacings, strength functions, and average radiation widths of a mixed sequence of s- and p-wave resonances whose parameters are supplied as input. The code is based on two physical assumptions: 1) The neutron reduced width distribution for each open channel is a chi-squared distribution with one degree of freedom, i.e. Porter-Thomas. 2) The spacing distribution follows the Gaussian Orthogonal Ensemble. This property is used, however, only to fix the s- to p-wave level density ratio as proportional to (2J+1) with a spin cut-off correction. B - Method of solution: The method used is an extension of that described by Moore et al. in reference (1), and is based on the method of moments of a truncated Porter-Thomas distribution. C - Restrictions on the complexity of the problem: Parameters for a maximum of 500 individual resonances can be specified. This restriction can be relaxed by increasing array dimensions

The Consequences of Indexing the Minimum Wage to Average Wages in the U.S. Economy.

Science.gov (United States)

Macpherson, David A.; Even, William E.

The consequences of indexing the minimum wage to average wages in the U.S. economy were analyzed. The study data were drawn from the 1974-1978 May Current Population Survey (CPS) and the 180 monthly CPS Outgoing Rotation Group files for 1979-1993 (approximate annual sample sizes of 40,000 and 180,000, respectively). The effects of indexing on the…

Index-based reactive power compensation scheme for voltage regulation

Science.gov (United States)

Dike, Damian Obioma

2008-10-01

Increasing demand for electrical power arising from deregulation and the restrictions posed to the construction of new transmission lines by environment, socioeconomic, and political issues had led to higher grid loading. Consequently, voltage instability has become a major concern, and reactive power support is vital to enhance transmission grid performance. Improved reactive power support to distressed grid is possible through the application of relatively unfamiliar emerging technologies of "Flexible AC Transmission Systems (FACTS)" devices and "Distributed Energy Resources (DERS)." In addition to these infrastructure issues, a lack of situational awareness by system operators can cause major power outages as evidenced by the August 14, 2003 widespread North American blackout. This and many other recent major outages have highlighted the inadequacies of existing power system indexes. In this work, a novel "Index-based reactive compensation scheme" appropriate for both on-line and off-line computation of grid status has been developed. A new voltage stability index (Ls-index) suitable for long transmission lines was developed, simulated, and compared to the existing two-machine modeled L-index. This showed the effect of long distance power wheeling amongst regional transmission organizations. The dissertation further provided models for index modulated voltage source converters (VSC) and index-based load flow analysis of both FACTS and microgrid interconnected power systems using the Newton-Raphson's load flow model incorporated with multi-FACTS devices. The developed package has been made user-friendly through the embodiment of interactive graphical user interface and implemented on the IEEE 14, 30, and 300 bus systems. The results showed reactive compensation has system wide-effect, provided readily accessible system status indicators, ensured seamless DERs interconnection through new islanding modes and enhanced VSC utilization. These outcomes may contribute

A Survey of Metal Lines at High Redshift. II. SDSS Absorption Line Studies—O VI Line Density, Space Density, and Gas Metallicity at z abs ~ 3.0

Science.gov (United States)

Frank, S.; Mathur, S.; Pieri, M.; York, D. G.

2010-09-01

We have analyzed a large data set of O VI absorber candidates found in the spectra of 3702 Sloan Digital Sky Survey (SDSS) quasars, focusing on a subsample of 387 active galactic nuclei sight lines with an average S/N >=5.0, allowing for the detection of absorbers above a rest-frame equivalent width limit of W r >= 0.19 Å for the O VI 1032 Å component. Accounting for random interlopers mimicking an O VI doublet, we derive for the first time a secure lower limit for the redshift number density ΔN/Δz for redshifts z abs >= 2.8. With extensive Monte Carlo simulations, we quantify the losses of absorbers due to blending with the ubiquitous Lyα forest lines and estimate the success rate of retrieving each individual candidate as a function of its redshift, the emission redshift of the quasar, the strength of the absorber, and the measured signal-to-noise ratio (S/N) of the spectrum by modeling typical Lyman forest spectra. These correction factors allow us to derive the "incompleteness and S/N-corrected" redshift number densities of O VI absorbers: ΔN O VI,c /Δzc (2.8 secure lower limit for the contribution of O VI to the closure mass density at the redshifts probed here: ΩO VI (2.8 = 1.9 × 10-8 h -1. We show that the strong lines we probe account for over 65% of the mass in the O VI absorbers; the weak absorbers, while dominant in line number density, do not contribute significantly to the mass density. Making a conservative assumption about the ionization fraction, {O VI}/{O}, and adopting the Anders & Grevesse solar abundance values, we derive the mean metallicity of the gas probed in our search: ζ(2.8 = 3.6 × 10-4 h, in good agreement with other studies. These results demonstrate that large spectroscopic data sets such as SDSS can play an important role in QSO absorption line studies, in spite of the relatively low resolution.

A SURVEY OF METAL LINES AT HIGH REDSHIFT. II. SDSS ABSORPTION LINE STUDIES-O VI LINE DENSITY, SPACE DENSITY, AND GAS METALLICITY AT zabs ∼ 3.0

International Nuclear Information System (INIS)

Frank, S.; Mathur, S.; Pieri, M.; York, D. G.

2010-01-01

We have analyzed a large data set of O VI absorber candidates found in the spectra of 3702 Sloan Digital Sky Survey (SDSS) quasars, focusing on a subsample of 387 active galactic nuclei sight lines with an average S/N ≥5.0, allowing for the detection of absorbers above a rest-frame equivalent width limit of W r ≥ 0.19 A for the O VI 1032 A component. Accounting for random interlopers mimicking an O VI doublet, we derive for the first time a secure lower limit for the redshift number density ΔN/Δz for redshifts z abs ≥ 2.8. With extensive Monte Carlo simulations, we quantify the losses of absorbers due to blending with the ubiquitous Lyα forest lines and estimate the success rate of retrieving each individual candidate as a function of its redshift, the emission redshift of the quasar, the strength of the absorber, and the measured signal-to-noise ratio (S/N) of the spectrum by modeling typical Lyman forest spectra. These correction factors allow us to derive the 'incompleteness and S/N-corrected' redshift number densities of O VI absorbers: ΔN O V I,c /Δz c (2.8 O V I,c /Δz c (3.2 O V I,c /Δz c (3.6 O V I (2.8 -8 h -1 . We show that the strong lines we probe account for over 65% of the mass in the O VI absorbers; the weak absorbers, while dominant in line number density, do not contribute significantly to the mass density. Making a conservative assumption about the ionization fraction, O VI /O, and adopting the Anders and Grevesse solar abundance values, we derive the mean metallicity of the gas probed in our search: ζ(2.8 -4 h, in good agreement with other studies. These results demonstrate that large spectroscopic data sets such as SDSS can play an important role in QSO absorption line studies, in spite of the relatively low resolution.

Line lessons: Enbridge's Northern Line provides valuable information

Energy Technology Data Exchange (ETDEWEB)

Ross, E.

2000-02-01

Experiences gained from the 14-year old Norman Wells crude oil pipeline in the Northwest Territories may provide operators with valuable insights in natural gas pipeline developments in northern Canada. The Norman Wells line is the first and only long-distance pipeline in North America buried in permafrost and has proven to be a veritable laboratory on pipeline behaviour in extremely cold climates which also happen to be discontinuous at the same time. The line was built by Enbridge with a 'limit state' design, i e. it was built to move within the permafrost within certain limits, the amount of movement depending upon the area in which the line was built. This technology, which is still cutting edge, allows the pipeline to react to the freeze-thaw cycle without being affected by the heaving and resettling. The knowledge gained from the Norman Wells Line has come in very useful in the more recent AltaGas Services project transporting natural gas from a nearby well into the the town of Inuvik. Enbridge also contributed to the development of various pipeline inspection tools such as the 'Geopig' which travels within the pipeline and can pinpoint the location of problems practically within a matter of inches, and the 'Rolligon' an amphibious vehicle with five-foot diameter rubber tires that displaces only two pounds per square inch, leaving barely a track as it travels along the right-of-way during times other than winter.

Extended analysis of the high resolution FTIR spectrum of 32S16O2 in the region of the ν2 band: Line positions, strengths, and pressure broadening widths

Science.gov (United States)

Ulenikov, O. N.; Bekhtereva, E. S.; Gromova, O. V.; Quack, M.; Mellau, G. Ch.; Sydow, C.; Bauerecker, S.

2018-05-01

The high resolution infrared spectra of sulfur dioxide (32S16O2) were recorded with a Bruker IFS 125HR Fourier transform infrared spectrometer (Zürich prototype ZP2001) in combination with a Ge:Cu detector and analyzed in the ν2 fundamental band region (400-650 cm-1 , ν0 ˜ = 517.8725691(77) cm-1). More than 4200 transitions were assigned in the experimental spectra to the ν2 band (the maximum values of the quantum numbers are Jmax. = 96 and Kamax. = 25). The subsequent weighted fit of experimentally assigned transitions was made with the Watson Hamiltonian. The 148 highly accurate MW transitions known from the literature have been also taken into account in the fit, resulting in a set of 33 parameters which reproduces the initial 1295 infrared ro-vibrational energy values from more than 4200 experimental line positions with a root mean square deviation drms = 1.5 ×10-4 cm-1. An analysis of 992 experimental ro-vibrational line intensities of the ν2 band was made, and a set of four effective dipole moment parameters was obtained which reproduces the initial experimental line intensities with a relative drms = 5.7 % . The half-widths of 146 ro-vibrational lines (Jmax. = 53 and Kamax. = 20) were analyzed from the multi-spectrum fit, and self-pressure broadening coefficients were determined.

A macrophage activation switch (MAcS)-index for assessment of monocyte/macrophage activation

DEFF Research Database (Denmark)

Maniecki, Maciej Bogdan; Lauridsen, Mette; Knudsen, Troels Bygum

2008-01-01

, simplified by the M1-M2 dichotomy of classically activated (M1), pro-inflammatory cells and alternatively activated (M2), anti-inflammatory cells. Macrophages, however, display a large degree of flexibility and are able to switch between activation states (1). The hemoglobin scavenger receptor CD163...... is expressed exclusively on monocytes and macrophages, and its expression is strongly induced by anti-inflammatory stimuli like IL10 and glucocorticoid, making CD163 an ideal M2 macrophage marker (2). Furthermore a soluble variant of CD163 (sCD163) is shed from the cell surface to plasma by protease mediated.......058-5139) (panti-inflammatory state.   CONCLUSION: We present a CD163-derived macrophage activation switch (MAcS)-index, which seems able to differentiate between (predominantly) pro-inflammatory and anti-inflammatory macrophage activation. The index needs...

Physical activity, but not sedentary time, influences bone strength in late adolescence.

Science.gov (United States)

Tan, Vina Ps; Macdonald, Heather M; Gabel, Leigh; McKay, Heather A

2018-03-20

Physical activity is essential for optimal bone strength accrual, but we know little about interactions between physical activity, sedentary time, and bone outcomes in older adolescents. Physical activity (by accelerometer and self-report) positively predicted bone strength and the distal and midshaft tibia in 15-year-old boys and girls. Lean body mass mediated the relationship between physical activity and bone strength in adolescents. To examine the influence of physical activity (PA) and sedentary time on bone strength, structure, and density in older adolescents. We used peripheral quantitative computed tomography to estimate bone strength at the distal tibia (8% site; bone strength index, BSI) and tibial midshaft (50% site; polar strength strain index, SSI p ) in adolescent boys (n = 86; 15.3 ± 0.4 years) and girls (n = 106; 15.3 ± 0.4 years). Using accelerometers (GT1M, Actigraph), we measured moderate-to-vigorous PA (MVPA Accel ), vigorous PA (VPA Accel ), and sedentary time in addition to self-reported MVPA (MVPA PAQ-A ) and impact PA (ImpactPA PAQ-A ). We examined relations between PA and sedentary time and bone outcomes, adjusting for ethnicity, maturity, tibial length, and total body lean mass. At the distal tibia, MVPA Accel and VPA Accel positively predicted BSI (explained 6-7% of the variance, p accounting for lean mass. Sedentary time did not independently predict bone strength at either site. Greater tibial bone strength in active adolescents is mediated, in part, by lean mass. Despite spending most of their day in sedentary pursuits, adolescents' bone strength was not negatively influenced by sedentary time.

Walking performance and muscle strength in the later stage poststroke: a nonlinear relationship.

Science.gov (United States)

Carvalho, Cristiane; Sunnerhagen, Katharina S; Willén, Carin

2013-05-01

To evaluate the relation between muscle strength in the lower extremities and walking performance (speed and distance) in subjects in the later stage poststroke and to compare this with normative data. A cross-sectional observational study. University hospital department. Subjects poststroke (n=41; 31 men, 10 women) with a mean age of 59±5.8 years and a time from stroke onset of 52±36 months were evaluated. An urban sample (n=144) of 40- to 79-year-olds (69 men, 75 women) formed the healthy reference group. Not applicable. Muscle strength in the lower extremities was measured with an isokinetic dynamometer and combined into a strength index. Values for the 30-meter walk test for self-selected and maximum speed and the 6-minute walk test were measured. A nonlinear regression model was used. The average strength index was 730±309 in the subjects after stroke compared with 1112±362 in the healthy group. A nonlinear relation between walking performance and muscle strength was evident. The model explained 37% of the variance in self-selected speed in the stroke group and 20% in the healthy group, and 63% and 38%, respectively, in the maximum walking speed. For the 6-minute walk test, the model explained 44% of the variance in the stroke group. Subjects in the later stage poststroke were weaker than the healthy reference group, and their weakness was associated with walking performance. At the same strength index, subjects walked at lower speeds and shorter distances after stroke, indicating that there are multiple impairments that affect walking ability. Treatments focused on increasing muscle strength thus continue to hold promise. Copyright © 2013 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Analytic EoS and PTW strength model recommendation for Starck Ta

Energy Technology Data Exchange (ETDEWEB)

Sjue, Sky K. [Los Alamos National Laboratory; Prime, Michael Bruce [Los Alamos National Laboratory

2016-09-01

The purpose of this document is to provide an analytic EoS and PTW strength model for Starck Ta that can be consistently used between different platforms and simulations at three labs. This should provide a consistent basis for comparison of the results of calculations, but not the best implementation for matching a wide variety of experimental data. Another version using SESAME tables should follow, which will provide a better physical representation over a broader range of conditions. The data sets available at the time only include one Hopkinson bar at a strain rate of 1800/s; a broader range of high-rate calibration data would be preferred. The resulting fit gives the PTW parameter p = 0. To avoid numerical issues, p = 0:001 has been used in FLAG. The PTW parameters that apply above the maximum strain rate in the data use the values from the original publication.

Multi-material topology design of laminates with strength criteria

DEFF Research Database (Denmark)

Lund, Erik

2012-01-01

The objective of this paper is to present a novel approach for multi-material topology optimization of laminated composite structures where strength constraints are taken into account together with other global structural performance measures. The topology design problem considered contains very...... many design variables, and when strength criteria are included in the problem, a very large number of criteria functions must be considered in the optimization problem to be solved. Thus, block aggregation methods are introduced, such that global strength measures are obtained. These formulations...... are illustrated for multi-material laminated design problems where the maximum failure index is minimized while compliance and mass constraints are taken into account....

Porous silica from rice husk ash for tundish lining

International Nuclear Information System (INIS)

Ahmed, Y.M.Z; Ewais, E.M.

2007-01-01

Type of materials as well as its compressive strength and degree of porosity are the determinal parameters for deciding the suitability of its usage as lining for tundish in continuous casting of steel. Silica is one of the materials suitable for such application. High porosity degree with high compressive strength of its compacts is special demands for increasing its efficiency. The suitability of producing porous silica compacts from the combustion of rice husk ash (RHA) appropriate for this application is the objective of the present work. Experimental design technique was used to evaluate the effect of different parameters (i.e. firing temperature, time and compaction pressure) controlling both porosity degree and compressive strength of rice husk ash compacts. The results revealed that while the porosity degree of the compacts decreased with increasing the entire studied parameters, its compressive strength exhibits another trend especially at lower soaking time. At lower soaking time, increasing firing temperature leads to a slight decrease in the compressive strength and then increased thereafter. Porous silica compacts having 30% porosity and > 25 kg/cm/sup 2/ compressive strength suitable for tundish lining could obtain from the combustion of rice husk ash compacts. (author)

Starlight excitation of permitted lines in the Orion Nebula

International Nuclear Information System (INIS)

Grandi, S.A.

1975-01-01

From an idealized model of the Orion Nebula and from an analysis of line ratios it is shown that direct starlight excitation of the permitted O I line dominates over recombination and Lyman line fluorescence. The line strengths predicted by this mechanism agree reasonably well with those observed in the Orion Nebula. The application of direct starlight excitation to other ions is also discussed

Design of block copolymer membranes using segregation strength trend lines

KAUST Repository

Sutisna, Burhannudin; Polymeropoulos, Georgios; Musteata, Valentina-Elena; Peinemann, Klaus-Viktor; Avgeropoulos, Apostolos; Smilgies, Detlef-M.; Hadjichristidis, Nikolaos; Nunes, Suzana Pereira

2016-01-01

composition, polymer molecular weights, casting solution concentration, and evaporation time. We propose here an effective method for designing new block copolymer membranes. The method consists of predetermining a trend line for the preparation of isoporous

Two Dimensional Symmetric Correlation Functions of the S Operator and Two Dimensional Fourier Transforms: Considering the Line Coupling for P and R Lines of Linear Molecules

Science.gov (United States)

Ma, Q.; Boulet, C.; Tipping, R. H.

2014-01-01

The refinement of the Robert-Bonamy (RB) formalism by considering the line coupling for isotropic Raman Q lines of linear molecules developed in our previous study [Q. Ma, C. Boulet, and R. H. Tipping, J. Chem. Phys. 139, 034305 (2013)] has been extended to infrared P and R lines. In these calculations, the main task is to derive diagonal and off-diagonal matrix elements of the Liouville operator iS1 - S2 introduced in the formalism. When one considers the line coupling for isotropic Raman Q lines where their initial and final rotational quantum numbers are identical, the derivations of off-diagonal elements do not require extra correlation functions of the ^S operator and their Fourier transforms except for those used in deriving diagonal elements. In contrast, the derivations for infrared P and R lines become more difficult because they require a lot of new correlation functions and their Fourier transforms. By introducing two dimensional correlation functions labeled by two tensor ranks and making variable changes to become even functions, the derivations only require the latters' two dimensional Fourier transforms evaluated at two modulation frequencies characterizing the averaged energy gap and the frequency detuning between the two coupled transitions. With the coordinate representation, it is easy to accurately derive these two dimensional correlation functions. Meanwhile, by using the sampling theory one is able to effectively evaluate their two dimensional Fourier transforms. Thus, the obstacles in considering the line coupling for P and R lines have been overcome. Numerical calculations have been carried out for the half-widths of both the isotropic Raman Q lines and the infrared P and R lines of C2H2 broadened by N2. In comparison with values derived from the RB formalism, new calculated values are significantly reduced and become closer to measurements.

Sociodemographic Characteristics, Behavioral Problems, Parental Concerns and Children’s Strengths Reported by Parents

Directory of Open Access Journals (Sweden)

Deisy Ribas Emerich

Full Text Available Abstract: Parental report is essential to understand adaptive difficulties in childhood. The aim of the study was to identify concerns of parents and qualities of children reported by parents, as well as the association of these variables with sociodemographic factors and child behavior problems. Parents of 353 schoolchildren from three public schools and one private school took part in the study. Assessment of behavior problems and parental reports about concerns and children’s strengths were obtained from the Child Behavior Checklist - CBCL. We submitted parents’ answers to the open-ended questions in the CBCL to a lexical analysis with the IRAMUTEQ software. Results concerning ‘strengths’ were related to affective and social interaction, while ‘concerns’ were related to academic performance and prevention of behavior problems. We concluded that parent concerns are targets of preventive interventions in childhood, while child strengths reported by parents are skills that need to be developed, as they help in adaptive functioning.

TIGER/Line Shapefile, 2017, nation, U.S., 115th Congressional District National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Current Tribal Block Group National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., Current Metropolitan Division National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., 115th Congressional District National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Current State and Equivalent National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Current Tribal Census Tract National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Current Tribal Census Tract National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Current State and Equivalent National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., Current Tribal Block Group National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., 114th Congressional District National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Current Tribal Block Group National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

Strength Development of High-Strength Ductile Concrete Incorporating Metakaolin and PVA Fibers

Directory of Open Access Journals (Sweden)

Muhammad Fadhil Nuruddin

2014-01-01

Full Text Available The mechanical properties of high-strength ductile concrete (HSDC have been investigated using Metakaolin (MK as the cement replacing material and PVA fibers. Total twenty-seven (27 mixes of concrete have been examined with varying content of MK and PVA fibers. It has been found that the coarser type PVA fibers provide strengths competitive to control or higher than control. Concrete with coarser type PVA fibers has also refined microstructure, but the microstructure has been undergone with the increase in aspect ratio of fibers. The microstructure of concrete with MK has also more refined and packing of material is much better with MK. PVA fibers not only give higher stiffness but also showed the deflection hardening response. Toughness Index of HSDC reflects the improvement in flexural toughness over the plain concrete and the maximum toughness indices have been observed with 10% MK and 2% volume fraction of PVA fibers.

Oscillator strength and quantum-confined Stark effect of excitons in a thin PbS quantum disk

Science.gov (United States)

Oukerroum, A.; El-Yadri, M.; El Aouami, A.; Feddi, E.; Dujardin, F.; Duque, C. A.; Sadoqi, M.; Long, G.

2018-01-01

In this paper, we report a study of the effect of a lateral electric field on a quantum-confined exciton in a thin PbS quantum disk. Our approach was performed in the framework of the effective mass theory and adiabatic approximation. The ground state energy and the stark shift were determined by using a variational method with an adequate trial wavefunction, by investigating a 2D oscillator strength under simultaneous consideration of the geometrical confinement and the electric field strength. Our results showed a strong dependence of the exciton binding and the Stark shift on the disk dimensions in both axial and longitudinal directions. On the other hand, our results also showed that the Stark shift’s dependence on the electric field is not purely quadratic but the linear contribution is also important and cannot be neglected, especially when the confinement gets weaker.

Constancy of spectral-line bisectors

International Nuclear Information System (INIS)

Gray, D.F.

1983-01-01

Bisectors of spectral line profiles in cool stars indicate the strength of convection in the photospheres of these objects. The present investigation is concerned with the feasibility of studying time variations in line bisectors, the reality of apparent line-to-line differences within the same stellar spectrum, and bisector differences between stars of identical spectral types. The differences considered pertain to the shape of the bisector. The material used in the investigation was acquired at the McDonald Observatory using a 1728 diode Reticon array at the coudefocus of the 2.1-m telescope. Observed bisector errors are discussed. It is established that different lines in the same star show significantly different bisectors. The observed error bands are shown by the shaded regions. The slope and curvature are unique for each case

Static design of steel-concrete lining for traffic tunnels

Science.gov (United States)

Vojtasik, Karel; Mohyla, Marek; Hrubesova, Eva

2017-09-01

Article summarizes the results of research focused on the structural design of traffic tunnel linings that have been achieved in the framework of a research project TE01020168 that supports The Technology Agency of Czech Republic. This research aim is to find and develop a process for design structure parameters of tunnel linings. These are now mostly build up by a shotcrete technology. The shotcrete is commonly endorsed either with steel girders or steel fibres. Since the installation a lining structure is loaded while strength and deformational parameters of shotcrete start to rise till the setting time elapses. That’s reason why conventional approaches of reinforced concrete are not suitable. As well as there are other circumstances to step in shown in this article. Problem is solved by 3D analysis using numerical model that takes into account all the significant features of a tunnel lining construction process inclusive the interaction between lining structure with rock massive. Analysis output is a view into development of stress-strain state in respective construction parts of tunnel lining the whole structure around, including impact on stability of rock massive. The proposed method comprises all features involved in tunnel fabrication including geotechnics and construction technologies.

222-S radioactive liquid waste line replacement and 219-S secondary containment upgrade, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1995-01-01

The U.S. Department of Energy (DOE) is proposing to: (1) replace the 222-S Laboratory (222-S) radioactive liquid waste drain lines to the 219-S Waste Handling Facility (219-S); (2) upgrade 219-S by replacing or upgrading the waste storage tanks and providing secondary containment and seismic restraints to the concrete cells which house the tanks; and (3) replace the transfer lines from 219-S to the 241-SY Tank Farm. This environmental assessment (EA) has been prepared in compliance with the National Environmental Policy Act (NEPA) of 1969, as amended, the Council on Environmental Quality Regulations for Implementing the Procedural Provisions of NEPA (40 Code of Federal Regulations [CFR] 1500-1508), and the DOE Implementing Procedures for NEPA (10 CFR 1021). 222-S is used to perform analytical services on radioactive samples in support of the Tank Waste Remediation System and Hanford Site environmental restoration programs. Activities conducted at 222-S include decontamination of analytical processing and support equipment and disposal of nonarchived radioactive samples. These activities generate low-level liquid mixed waste. The liquid mixed waste is drained through pipelines in the 222-S service tunnels and underground concrete encasements, to two of three tanks in 219-S, where it is accumulated. 219-S is a treatment, storage, and/or disposal (TSD) unit, and is therefore required to meet Washington Administrative Code (WAC) 173-303, Dangerous Waste Regulations, and the associated requirements for secondary containment and leak detection. The service tunnels are periodically inspected by workers and decontaminated as necessary to maintain as low as reasonably achievable (ALARA) radiation levels. Although no contamination is reaching the environment from the service tunnels, the risk of worker exposure is present and could increase. 222-S is expected to remain in use for at least the next 30 years to serve the Hanford Site environmental cleanup mission

Bone geometry, strength, and muscle size in runners with a history of stress fracture.

Science.gov (United States)

Popp, Kristin L; Hughes, Julie M; Smock, Amanda J; Novotny, Susan A; Stovitz, Steven D; Koehler, Scott M; Petit, Moira A

2009-12-01

Our primary aim was to explore differences in estimates of tibial bone strength, in female runners with and without a history of stress fractures. Our secondary aim was to explore differences in bone geometry, volumetric density, and muscle size that may explain bone strength outcomes. A total of 39 competitive distance runners aged 18-35 yr, with (SFX, n = 19) or without (NSFX, n = 20) a history of stress fracture were recruited for this cross-sectional study. Peripheral quantitative computed tomography (XCT 3000; Orthometrix, White Plains, NY) was used to assess volumetric bone mineral density (vBMD, mg x mm(-3)), bone area (ToA, mm(2)), and estimated compressive bone strength (bone strength index (BSI) = ToA x total volumetric density (ToD(2))) at the distal tibia (4%). Total (ToA, mm(2)) and cortical (CoA, mm(2)) bone area, cortical vBMD, and estimated bending strength (strength-strain index (SSIp), mm(3)) were measured at the 15%, 25%, 33%, 45%, 50%, and 66% sites. Muscle cross-sectional area (MCSA) was measured at the 50% and 66% sites. Participants in the SFX group had significantly smaller (7%-8%) CoA at the 45%, 50%, and 66% sites (P stress fracture. However, the lower strength was appropriate for the smaller muscle size, suggesting that interventions to reduce stress fracture risk might be aimed at improving muscle size and strength.

Protein-containing nutrient supplementation following strength training enhances the effect on muscle mass, strength, and bone formation in postmenopausal women

DEFF Research Database (Denmark)

Holm, Lars; Olesen, Jens L; Matsumoto, Keitaro

2008-01-01

.0 +/- 1.4%); nutrient group: 0.953 +/- 0.051 to 0.978 +/- 0.043 g/mm(3) (3.8 +/- 3.4%)] when adjusted for age, body mass index, and BMD at inclusion. Bone formation displayed an interaction (P increased osteocalcin at 24 wk in the nutrient group. In conclusion, we report...... that nutrient supplementation results in superior improvements in muscle mass, muscle strength, femoral neck BMD, and bone formation during 24 wk of strength training. The observed differences following such a short intervention emphasize the significance of postexercise nutrient supply on musculoskeletal......We evaluated the response of various muscle and bone adaptation parameters with 24 wk of strength training in healthy, early postmenopausal women when a nutrient supplement (protein, carbohydrate, calcium, and vitamin D) or a placebo supplement (a minimum of energy) was ingested immediately...

UV and X-ray spectral lines of Be-like Fe ion for plasma diagnostics

International Nuclear Information System (INIS)

Murakami, Izumi; Kato, Takako; Dubau, J.

1996-04-01

We have calculated X-ray and UV spectra of the Be-like Fe (FeXXIII) ion using collisional-radiative model including all fine-structure transitions among the 2s 2 , 2s2p, 2p 2 , 2snl, and 2pnl levels where n = 3 and 4, adopting data for the collision strengths by Zhang and Sampson (1992) and by Sampson, Goett, and Clark (1984). Some line intensity ratios can be used for the temperature diagnostic. We show 5 ratios in UV region and 9 ratios in X-ray region as functions of electron temperature and density at 0.3keV e e = 1-10 25 cm -3 . The effect of cascade in these line ratios is discussed. (author)

Associations between personality traits, physical activity level, and muscle strength

Science.gov (United States)

Tolea, Magdalena I.; Terracciano, Antonio; Simonsick, Eleanor M.; Metter, E. Jeffrey; Costa, Paul T.; Ferrucci, Luigi

2013-01-01

Associations among personality as measured by the Five Factor Model, physical activity, and muscle strength were assessed using data from the Baltimore Longitudinal Study of Aging (N = 1220, age: mean = 58, SD = 16). General linear modeling with adjustment for age, sex, race, and body mass index, and bootstrapping for mediation were used. We found neuroticism and most of its facets to negatively correlate with strength. The extraversion domain and its facets of warmth, activity, and positive-emotions were positively correlated with strength, independent of covariates. Mediation analysis results suggest that these associations are partly explained by physical activity level. Findings extend the evidence of an association between personality and physical function to its strength component and indicate health behavior as an important pathway. PMID:23966753

An acoustic Maxwell’s fish-eye lens based on gradient-index metamaterials

International Nuclear Information System (INIS)

Yuan Bao-guo; Tian Ye; Cheng Ying; Liu Xiao-jun

2016-01-01

We have proposed a two-dimensional acoustic Maxwell’s fish-eye lens by using the gradient-index metamaterials with space-coiling units. By adjusting the structural parameters of the units, the refractive index can be gradually varied, which is key role to design the acoustic fish-eye lens. As predicted by ray trajectories on a virtual sphere, the proposed lens has the capability to focus the acoustic wave irradiated from a point source at the surface of the lens on the diametrically opposite side of the lens. The broadband and low loss performance is further demonstrated for the lens. The proposed acoustic fish-eye lens is expected to have the potential applications in directional acoustic coupler or coherent ultrasonic imaging. (paper)

IndexCat

Data.gov (United States)

U.S. Department of Health & Human Services — IndexCat provides access to the digitized version of the printed Index-Catalogue of the Library of the Surgeon General's Office; eTK for medieval Latin texts; and...

Evaluation on correction factor for in-line X-ray phase contrast computed tomography

Energy Technology Data Exchange (ETDEWEB)

Jin, Mingli; Huang, Zhifeng; Zhang, Li; Zhang, Ran [Tsinghua Univ., Beijing (China). Dept. of Engineering Physics; Ministry of Education, Beijing (China). Key Laboratory of Particle and Radiation Imaging; Yin, Hongxia; Liu, Yunfu; Wang, Zhenchang [Capital Medical Univ., Beijing (China). Medical Imaging Center; Xiao, Tiqiao [Chinese Academy of Sciences, Shanghai (China). Shanghai Inst. of Applied Physics

2011-07-01

X-ray in-line phase contrast computed tomography (CT) is an effective nondestructive tool, providing 3D distribution of the refractive index of weakly absorbing low-Z object with high resolution and image contrast, especially with high-brilliance third-generation synchrotron radiation sources. Modified Bronnikov's algorithm (MBA), one of the in-line phase contrast CT reconstruction algorithms, can reconstruct the refractive index distribution of a pure phase object with a single computed tomographic data set. The key idea of the MBA is to use a correction factor in the filter function to stabilize the behavior at low frequencies. In this paper, we evaluate the influences of the correction factor to the final reconstruction results of the absorption-phase-mixed objects with analytical simulation and actual experiments. The limitations of the MBA are discussed finally. (orig.)

Infrared Dual-Line Hanle Diagnostic of the Coronal Vector Magnetic Field

Energy Technology Data Exchange (ETDEWEB)

Dima, Gabriel I.; Kuhn, Jeffrey R. [Institute for Astronomy, University of Hawaii, Pukalani, HI (United States); Berdyugina, Svetlana V., E-mail: gdima@hawaii.edu [Institute for Astronomy, University of Hawaii, Pukalani, HI (United States); Kiepenheuer Institut fuer Sonnenphysik, Freiburg (Germany); Predictive Science Inc., San Diego, CA (United States)

2016-04-20

Measuring the coronal vector magnetic field is still a major challenge in solar physics. This is due to the intrinsic weakness of the field (e.g., ~4G at a height of 0.1R⊙ above an active region) and the large thermal broadening of coronal emission lines. We propose using concurrent linear polarization measurements of near-infrared forbidden and permitted lines together with Hanle effect models to calculate the coronal vector magnetic field. In the unsaturated Hanle regime both the direction and strength of the magnetic field affect the linear polarization, while in the saturated regime the polarization is insensitive to the strength of the field. The relatively long radiative lifetimes of coronal forbidden atomic transitions implies that the emission lines are formed in the saturated Hanle regime and the linear polarization is insensitive to the strength of the field. By combining measurements of both forbidden and permitted lines, the direction and strength of the field can be obtained. For example, the SiX 1.4301 μm line shows strong linear polarization and has been observed in emission over a large field-of-view (out to elongations of 0.5 R⊙). Here we describe an algorithm that combines linear polarization measurements of the SiX 1.4301 μm forbidden line with linear polarization observations of the HeI 1.0830 μm permitted coronal line to obtain the vector magnetic field. To illustrate the concept we assume that the emitting gas for both atomic transitions is located in the plane of the sky. The further development of this method and associated tools will be a critical step toward interpreting the high spectral, spatial and temporal infrared spectro-polarimetric measurements that will be possible when the Daniel K. Inouye Solar Telescope (DKIST) is completed in 2019.

Deterioration of mechanical properties of high strength structural steel S460N under transient state fire condition

International Nuclear Information System (INIS)

Qiang, Xuhong; Bijlaard, Frans S.K.; Kolstein, Henk

2012-01-01

Highlights: ► Mechanical properties of S460N under transient state fire condition are obtained. ► Elevated-temperature mechanical properties of steels are dependent on steel grades. ► No design standard is applicable to HSS S460N under transient state fire condition. ► Specific statements on various HSS in fire should be proposed in design standards. ► Research results offer accurate material property for structural design engineers. -- Abstract: 911 World Trade Centre Tragedy put fire safety of constructional steel structures into question. Since then, more and more research attention has been paid to the elevated-temperature mechanical properties of structural steels, which is a critical basis of evaluating the fire performance of steel structures. In the literature the available mechanical properties of structural steels under fire conditions were mainly obtained from steady state test method, as steady state test method is easier to perform than transient state test method and offers stress–strain curves directly. However, the transient state fire condition is considered to be more realistic to represent the real condition when constructions are exposed to fire. In order to reveal the deterioration of mechanical properties of the commonly used high strength structural steel S460N under transient state fire condition, tensile tests were conducted under various constant stress levels up to 800 MPa. The reduction factors of elastic modulus, yield and ultimate strengths of S460N under transient state fire condition were obtained and compared with current leading design standards and available literature. The application of such accurate elevated-temperature mechanical properties reduction factors of S460N can ensure a safe fire-resistance design and evaluation of steel structures with high strength steel S460N under transient state fire condition. This experimental study also supports other relative research on fire performance of steel structures with

Leg strength or velocity of movement: which is more influential on the balance of mobility limited elders?

Science.gov (United States)

Mayson, Douglas J; Kiely, Dan K; LaRose, Sharon I; Bean, Jonathan F

2008-12-01

To determine which component of leg power (maximal limb strength or limb velocity) is more influential on balance performance in mobility limited elders. In this cross-sectional analysis we evaluated 138 community-dwelling older adults with mobility limitation. Balance was measured using the Unipedal Stance Test, the Berg Balance Test (BERG), the Dynamic Gait Index, and the performance-oriented mobility assessment. We measured one repetition maximum strength and power at 40% one repetition maximum strength, from which velocity was calculated. The associations between maximal estimated leg strength and velocity with balance performance were examined using separate multivariate logistic regression models. Strength was found to be associated [odds ratio of 1.06 (95% confidence interval, 1.01-1.11)] with performance on the Unipedal Stance Test, whereas velocity showed no statistically significant association. In contrast, velocity was consistently associated with performance on all composite measures of balance (BERG 14.23 [1.84-109.72], performance-oriented mobility assessment 33.92 [3.69-312.03], and Dynamic Gait Index 35.80 [4.77-268.71]). Strength was only associated with the BERG 1.08 (1.01-1.14). Higher leg press velocity is associated with better performance on the BERG, performance-oriented mobility assessment, and Dynamic Gait Index, whereas greater leg strength is associated with better performance on the Unipedal Stance Test and the BERG. These findings are likely related to the intrinsic qualities of each test and emphasize the relevance of limb velocity.

Strength training and body composition in middle-age women.

Science.gov (United States)

Burrup, Rachelle; Tucker, Larry A; LE Cheminant, James D; Bailey, Bruce W

2018-01-01

Strength training is a sound method to improve body composition. However, the effect of age, diet, menopause, and physical activity on the relationship between strength training and body composition in women remains unknown. The purpose of this study was to examine the intricacies of the relationship between strength training and body composition in 257 middle-age women and to quantify the effect of these factors on the association. The study was cross-sectional. Five variables were used to index strength training participation. Body composition was assessed by dual-energy X-ray absorptiometry. Diet was assessed by 7-day weighed food records, and physical activity was measured objectively using accelerometers. There were 109 strength trainers in the sample. For each day per week of strength training, body fat was 1.3 percentage points lower (F=14.8, Pdevote to strength training, the lower their body fat and the higher their fat-free mass tend to be. A significant portion of the differences in body composition seems to result from lifters participating in more physical activity than non-lifters. Menopause status also contributes significantly to the relationship.

Ulnar digits contribution to grip strength in patients with thumb carpometacarpal osteoarthritis is less than in normal controls.

Science.gov (United States)

Villafañe, Jorge H; Valdes, Kristin; Angulo-Diaz-Parreño, Santiago; Pillastrini, Paolo; Negrini, Stefano

2015-06-01

Grip testing is commonly used as an objective measure of strength in the hand and upper extremity and is frequently used clinically as a proxy measure of function. Increasing knowledge of hand biomechanics, muscle strength, and prehension patterns can provide us with a better understanding of the functional capabilities of the hand. The objectives of this study were to determine the contribution of ulnar digits to overall grip strength in individuals with thumb carpometacarpal (CMC) osteoarthritis (OA). Thirty-seven subjects participated in the study. This group consisted of 19 patients with CMC OA (aged 60-88 years) and 18 healthy subjects (60-88 years). Three hand configurations were used by the subjects during grip testing: use of the entire hand (index, middle, ring, and little fingers) (IMRL); use of the index, middle, and ring fingers (IMR); and use of only the index and middle fingers (IM). Grip strength findings for the two groups found that compared to their healthy counterparts, CMC OA patients had, on average, a strength deficiency of 45.6, 35.5, and 28.8 % in IMRL, IMR, and IM, respectively. The small finger contribution to grip is 14.3 % and the ring and small finger contribute 34 % in subjects with CMC OA. Grip strength decreases as the number of digits contributing decreased in both groups. The ulnar digits contribution to grip strength is greater than one third of total grip strength in subjects with CMC OA. Individuals with CMC OA demonstrate significantly decreased grip strength when compared to their healthy counterparts.

Assessing systematic risk in the S&P500 index between 2000 and 2011: A Bayesian nonparametric approach

OpenAIRE

Rodríguez, Abel; Wang, Ziwei; Kottas, Athanasios

2017-01-01

We develop a Bayesian nonparametric model to assess the effect of systematic risks on multiple financial markets, and apply it to understand the behavior of the S&P500 sector indexes between January 1, 2000 and December 31, 2011. More than prediction, our main goal is to understand the evolution of systematic and idiosyncratic risks in the U.S. economy over this particular time period, leading to novel sector-specific risk indexes. To accomplish this goal, we model the appearance of extreme l...

Energy Levels and Spectral Lines of Li Atoms in White Dwarf Strength Magnetic Fields

Science.gov (United States)

Zhao, L. B.

2018-04-01

A theoretical approach based on B-splines has been developed to calculate atomic structures and discrete spectra of Li atoms in a strong magnetic field typical of magnetic white dwarf stars. Energy levels are presented for 20 electronic states with the symmetries 20+, 20‑, 2(‑1)+, 2(‑1)‑, and 2(‑2)+. The magnetic field strengths involved range from 0 to 2350 MG. The wavelengths and oscillator strengths for the electric dipole transitions relevant to these magnetized atomic states are reported. The current results are compared to the limited theoretical data in the literature. A good agreement has been found for the lower energy levels, but a significant discrepancy is clearly visible for the higher energy levels. The existing discrepancies of the wavelengths and oscillator strengths are also discussed. Our investigation shows that the spectrum data of magnetized Li atoms previously published are obviously far from meeting requirements of analyzing discrete atomic spectra of magnetic white dwarfs with lithium atmospheres.

Identification of S VIII through S XIV emission lines between 17.5 and 50 nm in a magnetically confined plasma

Science.gov (United States)

McCarthy, K. J.; Tamura, N.; Combs, S. K.; García, R.; Hernández Sánchez, J.; Navarro, M.; Panadero, N.; Pastor, I.; Soleto, A.; the TJ-II Team

2018-03-01

43 spectral emission lines from F-like to Li-like sulphur ions have been identified in the wavelength range from 17.5 to 50 nm in spectra obtained following tracer injection into plasmas created in a magnetically confined plasma device, the stellarator TJ-II. Plasmas created and maintained in this heliac device with electron cyclotron resonance heating achieve central electron temperatures and densities up to 1.5 keV and 8 × 1018 m-3, respectively. Tracer injections were performed with ≤6 × 1016 atoms of sulphur contained within ˜300 μm diameter polystyrene capsules, termed tracer encapsulated solid pellets, using a gas propulsion system to achieve velocities between 250 and 450 m s-1. Once ablation of the exterior polystyrene shell by plasma particles is completed, the sulphur is deposited in the plasma core where it is ionized up to S+13 and transported about the plasma. In order to aid line identification, which is made using a number of atomic line emission databases, spectra are collected before and after injection using a 1 m focal length normal incidence spectrometer equipped with a CCD camera. This work is motivated by the need to clearly identify sulphur emission lines in the vacuum ultraviolet range of magnetically confined plasmas, as sulphur x-ray emission lines are regularly observed in both tokamak and stellarator plasmas.

Improving Strength-Ductility Balance of High Strength Dual-Phase Steels by Addition of Vanadium

Science.gov (United States)

Gong, Yu; Hua, M.; Uusitalo, J.; DeArdo, A. J.

For galvanized or galvannealed steels to be commercially successful, they must exhibit several attributes: (i) easy and inexpensive processing in the hot mill, cold mill and on the coating line, (ii) high strength with good formability and spot weldability, and (iii) good corrosion resistance, especially after cold forming. For good corrosion resistance, the coating must have sufficient coverage, be of uniform thickness, and most importantly, the coating must survive the cold stamping or forming operation. The purpose of this paper is to present research aiming at improving the steel substrate, such that high strength can be obtained while maintaining good global formability (tensile ductility), local formability (sheared-edge ductility), and good spot weldability. It is well-known that the strength of DP steels is controlled by several factors, including the amount of martensite found in the final microstructure. Recent research has revealed that the amount of austenite formed during intercritical annealing can be strongly influenced by the annealing temperature and the pre-annealing conditions of the hot band (coiling temperature) and cold band (% cold reduction). Current experiments have explored the combination of pre-annealing conditions and four annealing practices to help define the best practice to optimize the strength-formability balance in these higher strength DP steels. The steels used in these experiments contained (i) low carbon content for good spot weldability, (ii) the hardenability additions Mo and Cr for strength, and (iii) V for grain refinement, precipitation hardening and temper resistance. When processed correctly, these steels exhibited UTS levels up to 1000MPa, total elongation to 25%, reduction in area to 45%, and Hole Expansion Ratios to 50%. The results of this program will be presented and discussed.

Aerobic-Strength Exercise Improves Metabolism and Clinical State in Parkinson’s Disease Patients

Directory of Open Access Journals (Sweden)

Patrik Krumpolec

2017-12-01

Full Text Available Regular exercise ameliorates motor symptoms in Parkinson’s disease (PD. Here, we aimed to provide evidence that exercise brings additional benefits to the whole-body metabolism and skeletal muscle molecular and functional characteristics, which might help to explain exercise-induced improvements in the clinical state. 3-months supervised endurance/strength training was performed in early/mid-stage PD patients and age/gender-matched individuals (n = 11/11. The effects of exercise on resting energy expenditure (REE, glucose metabolism, adiposity, and muscle energy metabolism (31P-MRS were evaluated and compared to non-exercising PD patients. Two muscle biopsies were taken to determine intervention-induced changes in fiber type, mitochondrial content, and expression of genes related to muscle energy metabolism, as well as proliferative and regenerative capacity. Exercise improved the clinical disability score (MDS-UPDRS, bradykinesia, balance, walking speed, REE, and glucose metabolism and increased muscle expression of energy sensors (AMPK. However, the exercise-induced increase in muscle mass/strength, mitochondrial content, type II fiber size, and postexercise phosphocreatine (PCr recovery (31P-MRS were found only in controls. Nevertheless, MDS-UPDRS was associated with muscle AMPK and mechano-growth factor (MGF expression. Improvements in fasting glycemia were positively associated with muscle function and the expression of Sirt1 and Cox7a1, and the parameters of fitness/strength were positively associated with the expression of MyHC2, MyHC7, and MGF. Moreover, reduced bradykinesia was associated with better muscle metabolism (maximal oxidative capacity and postexercise PCr recovery; 31P-MRS. Exercise training improved the clinical state in early/mid-stage Parkinson’s disease patients, including motor functions and whole-body metabolism. Although the adaptive response to exercise in PD was different from that of controls, exercise

Using Simpson’s diversity index to examine multidimensional models of diversity in health professions education

Science.gov (United States)

McLaughlin, Gerald W.; McLaughlin, Josetta S.; White, Carla Y.

2016-01-01

Objectives This study explored new models of diversity for health professions education that incorporate multiple attributes and examined differences in diversity based on urbanicity, geographic region, and institutional structure. Methods Simpson’s Diversity Index was used to develop race, gender, and interprofessional diversity indices for health professions schools in the United States (N = 318). Sullivan’s extension was used to develop a composite diversity index that incorporated multiple individual attributes for each school. Pearson’s r was used to investigate correlations between continuous variables. ANOVA and independent t-tests were used to compare groups based on urbanicity, geographic region, and Basic Carnegie Classification. Results Mean (SD) for race, gender, and interprofessional  diversity indices were 0.36(0.17), 0.45(0.07), and 0.22(0.27) respectively. All correlations between the three indices were weak. The composite diversity index for this sample was 0.34(0.13). Significant differences in diversity were found between institutions based on urbanicity, Basic Carnegie Classification, and geographic region. Conclusions Multidimensional models provide support for expanding measures of diversity to include multiple characteristics and attributes. The approach demonstrated in this study enables institutions to complement and extend traditional measures of diversity as a means of providing evidence for decision-making and progress towards institutional initiatives. PMID:26724917

Shear bond strength of one-step self-etch adhesives to enamel: effect of acid pretreatment.

Science.gov (United States)

Poggio, Claudio; Scribante, Andrea; Della Zoppa, Federica; Colombo, Marco; Beltrami, Riccardo; Chiesa, Marco

2014-02-01

The purposes of this study were to evaluate the effect of surface pretreatment with phosphoric acid on the enamel bond strength of four-one-step self-etch adhesives with different pH values. One hundred bovine permanent mandibular incisors were used. The materials used in this study included four-one-step self-etch adhesives with different pH values: Adper(™) Easy Bond Self-Etch Adhesive (ph = 0,8-1), Futurabond NR (ph = 1,4), G-aenial Bond (ph = 1,5), Clearfil(3) S Bond (ph = 2,7). One two-step self-etch adhesive (Clearfil SE Bond/ph = 0,8-1) was used as control. The teeth were assigned into two subgroups according to bonding procedure. In the first subgroup (n = 50), no pretreatment agent was applied. In the second subgroup (n = 50), etching was performed using 37% phosphoric acid for 30 s. After adhesive systems application, a nanohybrid composite resin was inserted into the enamel surface. The specimens were placed in a universal testing machine (Model 3343, Instron Corp., Canton, Mass., USA). After the testing procedure, the fractured surfaces were examined with an optical microscope at a magnification of 10× to determine failure modes. The adhesive remnant index (ARI) was used to assess the amount of adhesive left on the enamel surface. Descriptive statistics of the shear bond strength and frequency distribution of ARI scores were calculated. Enamel pretreatment with phosphoric acid significantly increased bond strength values of all the adhesives tested. No significant differences in bond strength were detected among the four different one-step self-etch adhesives with different pH. Two-step self-etch adhesive showed the highest bond strength. © 2013 John Wiley & Sons A/S.

Allegheny County Map Index Grid

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Map Index Sheets from Block and Lot Grid of Property Assessment and based on aerial photography, showing 1983 datum with solid line and NAD 27 with 5 second grid...

Photospheric network from study of manganese lines

Energy Technology Data Exchange (ETDEWEB)

Elste, G; Teske, R G [Michigan Univ., Ann Arbor (USA). Dept. of Astronomy

1978-10-01

Area scans with the multi-channel magnetograph at the Kitt Peak McMath Telescope provided simultaneous measures of equivalent widths in two Mn lines, continuum intensity and longitudinal magnetic field component. Observations were carried out with apertures of 2.5 X 3.5 seconds arc and 1 X 1 seconds arc. For the network elements, which were identified using the magnetic field as tracer, the authors developed relationships between Isub(continuum), Wsub(lambda), Vsub(Doppler) and longitudinal field strength. With a minimum of assumptions it is possible to write from these observed relations an expression connecting true temperature perturbation in the line forming layers of the network to true longitudinal field strength. The results provide some constraints upon possible network models.

Derivation of electron density and temperature from (S II) and (O II) line intensity ratios

Energy Technology Data Exchange (ETDEWEB)

Canto, J; Meaburn, J; Theokas, A C [Manchester Univ. (UK). Dept of Astronomy; Elliott, K H [Anglo-Australian Observatory, Epping (Australia)

1980-12-01

Line intensity ratios for (S II) and (O II) due to collisional de-excitation are briefly discussed. Comparison is made between various reaction rate parameters presented by separate investigators. Included are observations of ratios obtained from the Orion nebula which experimentally confirm the reaction rates of Pradhan as best representing the observed distribution of these ratios. (O II) and (S II) contour plots are also presented, which allow effective electron temperatures and densities to be estimated from pairs of line ratios.

Protein-containing nutrient supplementation following strength training enhances the effect on muscle mass, strength, and bone formation in postmenopausal women

DEFF Research Database (Denmark)

Holm, Lars; Olesen, J.L.; Matsumoto, K.

2008-01-01

.4%); nutrient group: 0.953 ± 0.051 to 0.978 ± 0.043 g/mm3 (3.8 ± 3.4%)] when adjusted for age, body mass index, and BMD at inclusion. Bone formation displayed an interaction (P increased osteocalcin at 24 wk in the nutrient group. In conclusion, we report that nutrient supplementation...... results in superior improvements in muscle mass, muscle strength, femoral neck BMD, and bone formation during 24 wk of strength training. The observed differences following such a short intervention emphasize the significance of postexercise nutrient supply on musculoskeletal maintenance.......We evaluated the response of various muscle and bone adaptation parameters with 24 wk of strength training in healthy, early postmenopausal women when a nutrient supplement (protein, carbohydrate, calcium, and vitamin D) or a placebo supplement (a minimum of energy) was ingested immediately...

Implications of the stagnation line model for energy input through the dayside magnetopause

International Nuclear Information System (INIS)

Pudovkin, M.I.; Semenov, V.S.; Heyn, M.F.; Biernat, H.K.

1986-01-01

Based on the formation of a stagnation line at the magnetopause the electromagnetic energy transport from the solar wind into the dayside magnetosphere is analyzed. The resulting energy flux is analyzed. The resulting energy flux is proportional to v/sub infinity/B/sub infinity/sin 2 (theta/sub infinity/-phi/sub infinity/), where v/sub infinity/ and B/sub infinity/ are the solar wind speed and magnetic field and theta/sub infinity/-phi/sub s/infinity is the angle between the IMF and the stagnation line projected into the interplanetary space. A stagnation line parallel to the separator gives approximately the sin 4 (theta/sub infinity//2) energy flux dependence of Akasofu's epsilon-index

Tensile strength and fatigue strength of 6061 aluminum alloy friction welded joints

Energy Technology Data Exchange (ETDEWEB)

Ochi, H.; Tsujino, R. [Osaka Inst. of Tech., Asahi-ku Osaka (Japan); Sawai, T. [Osaka Sangyo Univ., Daito (Japan); Yamamoto, Y. [Setsunan Univ., Neyagawa (Japan); Ogawa, K. [Osaka Prefecture Univ., Sakai (Japan); Suga, Y. [Keio Univ., Kohoku-ku, Yokohama (Japan)

2002-07-01

Friction welding of 6061 aluminum alloy was carried out in order to examine the relationship between deformation heat input in the upset stage and joint performance. The joint performance was evaluated by tensile testing and fatigue testing. Stabilized tensile strength was obtained when the deformation heat input in the upset stage exceeded 200 J/s. Weld condition at the weld interface and the width of softened area affected fatigue strength more than tensile strength. That is, when the weld condition at the weld interface is good and the softened area is wide, fatigue strength increases. On the other hand, when the weld condition at the weld interface is good and the softened area is narrow, and when the weld condition at the weld interface is somewhat poor in spite of the wide softened area, fatigue strength decreases. The fatigue limit obtained by the fatigue testing revealed that, when the deformation heat input in the upset stage exceeded a certain value, sound joints could be produced. (orig.)

Determination of core level line widths in XPS of GeS and GeSe

International Nuclear Information System (INIS)

Viljoen, P.E.

1981-01-01

Measured X-ray photoelectron spectra are broadened owing to several factors. They can be regarded as the sums of the instrument response functions and the finite source widths. By measuring the response function and deconvoluting the measured peak, the form of the measured peak, the instrument function and the deconvoluted line were determined. The former two seem to have a Gauss and the latter a Lorentz form. The X-ray source is known to have a Lorentz form. A simple method, using the shapes of all these lines, is proposed to determine the line width. Applied to GeS and GeSe lines it gives values that agree quite well with other determinations. Strictly speaking, the method is only applicable to our or other similar spectrometers, but it can be generally applied if the line shapes are known or can be determined [af

Rolling estimations of long range dependence volatility for high frequency S&P500 index

Science.gov (United States)

Cheong, Chin Wen; Pei, Tan Pei

2015-10-01

This study evaluates the time-varying long range dependence behaviors of the S&P500 volatility index using the modified rescaled adjusted range (R/S) statistic. For better computational result, a high frequency rolling bipower variation realized volatility estimates are used to avoid possible abrupt jump. The empirical analysis findings allow us to understand better the informationally market efficiency before and after the subprime mortgage crisis.

Adhesion strength of a living cell to various substrates measured using a cup-attached atomic force microscopy chip

Science.gov (United States)

Kim, Hyonchol; Ishibashi, Kenta; Matsuo, Kosuke; Kira, Atsushi; Onomura, Yui; Okada, Tomoko; Nakamura, Chikashi

2018-03-01

Cell adhesion strengths to various substrates were quantitatively measured using atomic force microscopy (AFM). A cup-shaped metal hemisphere was attached to the apex of the AFM cantilever, the “cup-chip” approached a cell (FP10SC2) to pick it up, the captured cell approached any one of six different substrates [gold (Au), nickel (Ni), bovine serum albumin (BSA), an amino group (NH2), poly(tetrafluoroethylene) (PTFE), and structured PTFE (sPTFE)], and the cell adhesion strength at the initial contact period was evaluated by detaching the cell from the substrate. The results obtained showed that the force needed to detach the cell from the NH2 substrate was more than 3-fold larger than that of metal substrates (Au and Ni), more than 15-fold larger than that of biochemically treated substrates (BSA), and more than 20-fold larger than that of hydrophobic substrates (PTFE and sPTFE). Using differences in adhesion strengths, a cell on a sPTFE substrate was picked up using a BSA-coated cup-chip, placed on a NH2 substrate, repeating this cell manipulation five times, and line patterning of cells was achieved. These results indicate that measurements of cell adhesion strength are fundamental to fabricate desired cell networks and the cup-chip is a useful tool for achieving easy cell manipulation.

‘Domestic utility and useful lines: Jean-Charles Krafft’s and Thomas Hope’s outlines’

Directory of Open Access Journals (Sweden)

Alexis H. Cohen

2013-12-01

Full Text Available Through a study of design publications by the architect and draughtsman, Jean-Charles Krafft (1764-1833, and aristocrat and designer Thomas Hope (1769-1831, this paper examines how Neoclassicism’s material products – its architecture and objects of interior design – participated in an intellectual history of utility c. 1800. This paper gives special attention to the outline drawing, arguing that its graphic idiom is an integral feature of Krafft and Hope’s work, linking the value they ascribe to useful buildings and objects to ideas about how the lines of their illustrations were to participate both in design processes and in the promotion of neoclassical aesthetics.

A Novel Index for Online Voltage Stability Assessment Based on Correlation Characteristic of Voltage Profiles

Directory of Open Access Journals (Sweden)

M. R. Aghamohammadi

2011-06-01

Full Text Available Abstract: Voltage instability is a major threat for security of power systems. Preserving voltage security margin at a certain limit is a vital requirement for today’s power systems. Assessment of voltage security margin is a challenging task demanding sophisticated indices. In this paper, for the purpose of on line voltage security assessment a new index based on the correlation characteristic of network voltage profile is proposed. Voltage profile comprising all bus voltages contains the effect of network structure, load-generation patterns and reactive power compensation on the system behaviour and voltage security margin. Therefore, the proposed index is capable to clearly reveal the effect of system characteristics and events on the voltage security margin. The most attractive feature for this index is its fast and easy calculation from synchronously measured voltage profile without any need to system modelling and simulation and without any dependency on network size. At any instant of system operation by merely measuring network voltage profile and no further simulation calculation this index could be evaluated with respect to a specific reference profile. The results show that the behaviour of this index with respect to the change in system security is independent of the selected reference profile. The simplicity and easy calculation make this index very suitable for on line application. The proposed approach has been demonstrated on IEEE 39 bus test system with promising results showing its effectiveness and applicability.

Body image, nutritional status, abdominal strength, and cardiorespiratory fitness in children and adolescents practicing sports.

Science.gov (United States)

Schubert, Alexandre; Januário, Renata Selvatici B; Casonatto, Juliano; Sonoo, Christi Noriko

2013-01-01

To verify the association between nutritional status, physical fitness, and body image in children and adolescents. This cross-sectional study included 401 students (236 boys and 165 girls) aged between 8 and 16 years that were regularly enrolled in sports in the local clubs. The nutritional status was evaluated by the body mass index. Students were assessed for satisfaction with body image, abdominal strength resistance, and cardiorespiratory fitness. The variables were assessed on the same day following a standardized order. In order to verify relationships between variables, the chi-square test was used. Afterwards, the binary logistic regression was applied to identify the magnitude of the associations, considering p<0.05 as significant. Association was found between body image and body mass index (p=0.001), abdominal strength resistance (p=0.005) and cardiorespiratory fitness (p=0.001). The Odds Ratio for presenting the body image insatisfaction for those who have not achieved the expected values for the health criteria in abdominal strength resistance and cardiorespiratory fitness were 2.14 and 2.42 times respectively, and for those with overweight and obesity, 2.87 times. Insatisfaction with body image is associated with body mass index and also with physical fitness, abdominal strength resistance, and cardiorespiratory fitness variables.

Controller Design of Complex System Based on Nonlinear Strength

Directory of Open Access Journals (Sweden)

Rongjun Mu

2015-01-01

Full Text Available This paper presents a new idea of controller design for complex systems. The nonlinearity index method was first developed for error propagation of nonlinear system. The nonlinearity indices access the boundary between the strong and the weak nonlinearities of the system model. The algorithm of nonlinearity index according to engineering application is first proposed in this paper. Applying this method on nonlinear systems is an effective way to measure the nonlinear strength of dynamics model over the full flight envelope. The nonlinearity indices access the boundary between the strong and the weak nonlinearities of system model. According to the different nonlinear strength of dynamical model, the control system is designed. The simulation time of dynamical complex system is selected by the maximum value of dynamic nonlinearity indices. Take a missile as example; dynamical system and control characteristic of missile are simulated. The simulation results show that the method is correct and appropriate.

Coffee Index as Quick and Simple Indicator of Purchasing Power Parity

Directory of Open Access Journals (Sweden)

Jakub Fischer

2018-03-01

Full Text Available Purchasing Power Parity is the corner stone of all international comparisons. Various approaches to Purchasing Power Parity, such as the Big Mac Index, KFC Index, iPad Index, Tall Latte Index or Ikea Index were popularized to the broader audience besides the OECD Purchasing Power Parity indices. The aim of this paper is to develop a new ready-to-use quick and simple index based on the prices of Nespresso coffee’s capsules and show the main challenges of such indices as well as of the PPP concept. For the purpose of our research the data on the Nespresso capsules prices were collected. Taking into account also the popularity (demand side of the capsules types, the Espresso line was chosen as the basis for which all further calculations are made. The Nespresso Index provides us with clear evidence that the Law of One Price cannot work in recent world because of three key features. Firstly, differences in taxes make the perfect parity impossible. Secondly, the price discrimination prevents the rational subjects from arbitrage. Finally, the changes in the exchange rate make such indices highly volatile. Despite these weaknesses, the Nespresso Index could be used as the useful supplement of the OECD PPP as it is low cost, easy and fast to compute and digestible for the lay public.

Fracture strength of aluminium alloys under rapid loading conditions

International Nuclear Information System (INIS)

Joshi, K.D.; Rav, Amit S.; Sur, Amit; Kaushik, T.C.; Gupta, Satish C.

2016-04-01

Spall fracture strength and dynamic yield strength of aluminium alloys have been measured at high strain rates generated in plate impact experiments carried out at different impact velocities ranging from 174 m/s to 560 m/s using single stage gas gun facility. In each experiment, the free surface velocity history of the sample plate of aluminium alloy has been derived from time resolved Doppler shift measured employing indigenously developed velocity interferometer system for any reflector (VISAR). The free surface velocity history so determined has been used to evaluate the spall fracture strength and dynamic yield strength of the target material. The two kinds of alloys of aluminium namely Al2014-T4 and Al2024-T4 have been investigated in these experiments. In Al2014-T4 target plates, the spall strength determined from free surface velocity history recorded for impact velocities of 179 m/s, 307 m/s, 398 m/s and 495m/s is 0.90 GPa, 0.96 GPa, 1.0 GPa and 1.1 GPa, respectively. The average strain rates just ahead of spall pulse have been found to vary from ∼ 1.1×10 4 /s to 2.4×10 4 /s. The dynamic yield strength derived from the measured Hugoniot elastic limit ranges from 0.36 GPa to 0.40 GPa. The spall strength for Al2024-T4 samples has been determined to be 1.11 GPa, 1.18 GPa and 1.42 GPa, at impact velocities of 174 m/s, 377 m/s and 560 m/s, respectively. The corresponding average strain rates range from 1.9×104/s to 2.5×104/s. The dynamic yield strength of Al2024-T4 at these impact velocities has been found to vary from 0.37 GPa to 0.43 GPa. The measured spall strengths in all these experiments are higher than the quasi-static value of 0.511 GPa for Al2014-T4 and 0.470 GPa for Al2024. Similarly, the dynamic yield strengths are also larger than the quasi-static value of 0.355 GPa for Al2014-T4 and 0.360 GPa for Al2024-T4. These experimental studies suggest that at high strain rates, both the alloys of aluminium offer higher resistance against the tensile

Nutritional status is the major factor affecting grip strength of African HIV patients before and during antiretroviral treatment.

Science.gov (United States)

Filteau, S; PrayGod, G; Woodd, S L; Friis, H; Heimburger, D C; Koethe, J R; Kelly, P; Kasonka, L; Rehman, A M

2017-10-01

Low grip strength is a marker of frailty and a risk factor for mortality among HIV patients and other populations. We investigated factors associated with grip strength in malnourished HIV patients at referral to ART, and at 12 weeks and 2-3 years after starting ART. The study involved HIV-infected Zambian and Tanzanian participants recruited to the NUSTART trial when malnourished (body mass index <18.5 kg/m 2 ) and requiring ART. The relationship of grip strength to nutritional, infectious and demographic factors was assessed by multivariable linear regression at referral for ART (n = 1742) and after 12 weeks (n = 778) and 2-3 years of ART (n = 273). In analyses controlled only for sex, age and height, most nutrition and infection-related variables were associated with grip strength. However, in multivariable analyses, consistent associations were seen for fat-free mass index, mid-upper arm circumference, haemoglobin and systolic blood pressure, and a variable association with fat mass index in men. C-reactive protein and CD4 count had limited independent effects on grip strength, while receiving tuberculosis treatment was associated with weaker grip strength. In this population of originally malnourished HIV patients, poor grip strength was more strongly and independently associated with nutritional than with infection and inflammation variables. Programmes to improve health and survival of HIV patients should incorporate nutritional assessment and management and could use grip strength as a functional indicator of improving nutrition. © 2017 John Wiley & Sons Ltd.

Applicability of geomechanical classifications for estimation of strength properties in Brazilian rock masses.

Science.gov (United States)

Santos, Tatiana B; Lana, Milene S; Santos, Allan E M; Silveira, Larissa R C

2017-01-01

Many authors have been proposed several correlation equations between geomechanical classifications and strength parameters. However, these correlation equations have been based in rock masses with different characteristics when compared to Brazilian rock masses. This paper aims to study the applicability of the geomechanical classifications to obtain strength parameters of three Brazilian rock masses. Four classification systems have been used; the Rock Mass Rating (RMR), the Rock Mass Quality (Q), the Geological Strength Index (GSI) and the Rock Mass Index (RMi). A strong rock mass and two soft rock masses with different degrees of weathering located in the cities of Ouro Preto and Mariana, Brazil; were selected for the study. Correlation equations were used to estimate the strength properties of these rock masses. However, such correlations do not always provide compatible results with the rock mass behavior. For the calibration of the strength values obtained through the use of classification systems, ​​stability analyses of failures in these rock masses have been done. After calibration of these parameters, the applicability of the various correlation equations found in the literature have been discussed. According to the results presented in this paper, some of these equations are not suitable for the studied rock masses.

An in vitro Evaluation of Shear Bond Strength of Adhesive Precoated Brackets

Directory of Open Access Journals (Sweden)

A S Sibi

2014-01-01

Full Text Available Newer materials have been introduced in the field of orthodontics to improve clinical efficacy as well as to simplify the technique. In an effort to reduce the time and steps to bond orthodontic attachments, adhesive precoated (APC brackets were introduced. In this study, an attempt is made to evaluate the shear bond strength (SBS and debonding behavior of APC brackets compared with uncoated ceramic brackets. A total of 60 human premolar teeth were divided into two groups of 30 each, bonded with APC ceramic brackets and uncoated ceramic brackets. Group I bonded with APC brackets as prescribed by the manufacturers and group II was bonded with conventional bonding using Turbobond. After bonding, sthe samples were kept in distilled water at 37°C for 24 hours and a universal testing mechine was used to apply an occlusal shear force at a speed of 0.5 mm/min. The shear bond strength of the groups was compared using Student t-test and the debonding behavior were compared using Mann-Whitney′s U test. Mean shear bond strength and standard deviation of the groups were group I - 9.09 ± 2.5 MPa and group II - 12.95 ± 2.81 MPa. There were significant differences in bond strength observed between the two groups. The debonding behavior showed an adhesive remnant index score of 0.90 ± 0.08 for group I and 1.10 ± 0.04 for group II, which indicates there is significant difference between each other. When considering the values required for optimum bond strength, APC brackets in this study showed adequate bond strength and could be used for routine clinical use.

Climate Prediction Center (CPC) Madden-Julian Oscillation (MJO) Index

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Climate Prediction Center (CPC) Madden Julian Oscillation index (MJO) is a dataset that allows evaluation of the strength and phase of the MJO during the dataset...

TIGER/Line Shapefile, 2015, nation, U.S., Current County and Equivalent National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, 2010 nation, U.S., 2010 Census Urban Area National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Current Combined Statistical Area (CSA) National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Current Combined Statistical Area (CSA) National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., Current State and Equivalent National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Topological Faces-Military Installation Relationship File

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, nation, U.S., Current Tribal Census Tract National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Current County and Equivalent National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, 2010 nation, U.S., 2010 Census Urban Area National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2015, 2010 nation, U.S., 2010 Census Urban Area National

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2016, nation, U.S., Topological Faces-Military Installation Relationship File

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

TIGER/Line Shapefile, 2017, nation, U.S., Current County and Equivalent National Shapefile

Data.gov (United States)

US Census Bureau, Department of Commerce — The TIGER/Line shapefiles and related database files (.dbf) are an extract of selected geographic and cartographic information from the U.S. Census Bureau's Master...

Leg Strength or Velocity of Movement Which Is More Influential on the Balance of Mobility Limited Elders?

Science.gov (United States)

Mayson, Douglas J.; Kiely, Dan K.; LaRose, Sharon I.; Bean, Jonathan F.

2009-01-01

Objective To determine which component of leg power (maximal limb strength or limb velocity) is more influential on balance performance in mobility limited elders. Design In this cross-sectional analysis we evaluated 138 community-dwelling older adults with mobility limitation. Balance was measured using the Unipedal Stance Test, the Berg Balance Test (BERG), the Dynamic Gait Index, and the performance-oriented mobility assessment. We measured one repetition maximum strength and power at 40% one repetition maximum strength, from which velocity was calculated. The associations between maximal estimated leg strength and velocity with balance performance were examined using separate multivariate logistic regression models. Results Strength was found to be associated [odds ratio of 1.06 (95% confidence interval, 1.01–1.11)] with performance on the Unipedal Stance Test, whereas velocity showed no statistically significant association. In contrast, velocity was consistently associated with performance on all composite measures of balance [BERG 14.23 (1.84–109.72), performance-oriented mobility assessment 33.92 (3.69–312.03), and Dynamic Gait Index 35.80 (4.77–268.71))]. Strength was only associated with the BERG 1.08 (1.01–1.14). Conclusions Higher leg press velocity is associated with better performance on the BERG, performance-oriented mobility assessment, and Dynamic Gait Index, whereas greater leg strength is associated with better performance on the Unipedal Stance Test and the BERG. These findings are likely related to the intrinsic qualities of each test and emphasize the relevance of limb velocity. PMID:19033758

Soft radiative strength in warm nuclei

International Nuclear Information System (INIS)

Becker, J A; Bernstein, L A; Garrett, P E; Nelson, R O; Schiller, A; Voinov, A; Agvaanluvsan, U; Algin, E; Belgya, T; Chankova, R; Guttormsen, M; Mitchell, G E; Rekstad, J; Siem, S

2004-01-01

Unresolved transitions in the nuclear γ-ray cascade produced in the decay of excited nuclei are best described by statistical concepts: a continuous radiative strength function (RSF) and level density yield mean values of transition matrix elements. Data on the soft (E γ < 3-4 MeV) RSF for transitions between warm states (i.e. states several MeV above the yrast line) have, however, remained elusive

Relationship between depression with FEV1 percent predicted and BODE index in chronic obstructive pulmonary disease

Science.gov (United States)

Gunawan, H.; Hanum, H.; Abidin, A.; Hanida, W.

2018-03-01

WHO reported more than 3 million people die from COPD in 2012 and are expected to rank third after cardiovascular and cancer diseases in the future. Recent studies reported the prevalence of depression in COPD patients was higher than in control group. So, it’s important for clinicians to understand the relationship of depression symptoms with clinical aspects of COPD. For determining the association of depression symptoms with lung function and BODE index in patients with stable COPD, a cross-sectional study was in 98 stable COPD outpatients from January to June 2017. Data were analyzed using Independent t-test, Mann-Whitney test, and Spearman’s rank correlation. COPD patients with depression had higher mMRC scores, and lower FEV1 percent predicted, and then 6-Minutes Walk Test compared to those without depression. There was a moderate strength of correlation (r=-0.43) between depression symptoms and FEV1 percent predicted, and strong correlation (r=0.614) between depression symptoms and BODE index. It indicates that BODE index is more accurate to describe symptoms of depression in COPD patients.

Relation of geomagnetic activity index variations with parameters of interplanetary scintillations

International Nuclear Information System (INIS)

Vlasov, V.I.; Shishov, V.I.; Shishova, T.D.

1985-01-01

A correlation between the Asub(p)-index of geomagnetic activity, index of interplanetary scintillations and solar wind velocity, has been considered depending on the spatial position of the interplanetary plasma (IPP) regions under study. It is shown, that the scintillation index can be used to forecast the geomagnetic activity, whereas the solar wind velocity can not be used for the purpose. Heliolongitudinal dependence of geoeffectiveness of IPP sreading perturbations agrees well with their structure in the heliolongitudinal cross section (and, on the whole, with the angular structure and direction of IPP perturbation spread). To use interplanetary scintillations in forecasting the geomagnetic activity (on the level of correlation not below 0.5), the angular distance of the investigated IPP regions relative to the Sun-Earth line on the average should not exceed 30-40 deg. The time of delay between the moments of observation of variations in the scintillation index the time of passage of the corresponding heliocentric distances at an average rate of the interplanetary perturbation spread approximately 500 km/s

Dual task multimodal physical training in Alzheimer’s disease: effect on cognitive functions and muscle strength

Directory of Open Access Journals (Sweden)

Bruno Naves Ferreira

2017-12-01

Full Text Available The aim of this study was to evaluate the effects of dual task multimodal physical training (MPT on the cognitive functions and muscle strength in older adults with Alzheimer’s disease. Participants were 19 subjects with AD in the mild and moderate stages, divided into training group (TG and control group (CG. The TG performed dual task MPT for 12 weeks. Subjects were evaluated at the pre- and post-intervention moments. The Mini Mental State Examination (MMSE, Clock Drawing Test (CDT and Frontal Assessment Battery (FAB were used to assess cognition. For muscle strength, the Chair Lift and Sit Test (CLST and Manual Grasp Force (MGF were used. The Wilcoxon test was used to analyze pre and post intragroup moments. The TG showed a significant improvement in FAB and CLST (p≤0.05 and a tendency to improve the MMSE score (p≤0.08. The CG showed significant improvement in CLST (p≤0.05. Dual task MPT improves the frontal cognitive functions and lower limb muscle strength of older adults with AD.

An ionospheric index suitable for estimating the degree of ionospheric perturbations

Science.gov (United States)

Wilken, Volker; Kriegel, Martin; Jakowski, Norbert; Berdermann, Jens

2018-03-01

Space weather can strongly affect trans-ionospheric radio signals depending on the used frequency. In order to assess the strength of a space weather event from its origin at the sun towards its impact on the ionosphere a number of physical quantities need to be derived from scientific measurements. These are for example the Wolf number sunspot index, the solar flux density F10.7, measurements of the interplanetary magnetic field, the proton density, the solar wind speed, the dynamical pressure, the geomagnetic indices Auroral Electrojet, Kp, Ap and Dst as well as the Total Electron Content (TEC), the Rate of TEC, the scintillation indices S4 and σ(ϕ) and the Along-Arc TEC Rate index index. All these quantities provide in combination with an additional classification an orientation in a physical complex environment. Hence, they are used for brief communication of a simplified but appropriate space situation awareness. However, space weather driven ionospheric phenomena can affect many customers in the communication and navigation domain, which are still served inadequately by the existing indices. We present a new robust index, that is able to properly characterize temporal and spatial ionospheric variations of small to medium scales. The proposed ionospheric disturbance index can overcome several drawbacks of other ionospheric measures and might be suitable as potential driver for an ionospheric space weather scale.

EJSCREEN Indexes 2015 Public

Data.gov (United States)

U.S. Environmental Protection Agency — There is an EJ Index for each environmental indicator. There are eight EJ Indexes in EJSCREEN reflecting the 8 environmental indicators. The EJ Index names are:...

EJSCREEN Indexes 2016 Public

Data.gov (United States)

U.S. Environmental Protection Agency — There is an EJ Index for each environmental indicator. There are eleven EJ Indexes in EJSCREEN reflecting the 11 environmental indicators. The EJ Index names are:...

Hamstrings strength imbalance in professional football (soccer) players in Australia.

Science.gov (United States)

Ardern, Clare L; Pizzari, Tania; Wollin, Martin R; Webster, Kate E

2015-04-01

The aim of this study was to describe the isokinetic thigh muscle strength profile of professional male football players in Australia. Concentric (60° and 240°·s(-1)) and eccentric (30° and 120°·s(-1)) hamstrings and quadriceps isokinetic strength was measured with a HUMAC NORM dynamometer. The primary variables were bilateral concentric and eccentric hamstring and quadriceps peak torque ratios, concentric hamstring-quadriceps peak torque ratios, and mixed ratios (eccentric hamstring 30°·s(-1) ÷ concentric quadriceps 240°·s(-1)). Hamstring strength imbalance was defined as deficits in any 2 of: bilateral concentric hamstring peak torque ratio imbalance. Athletes with strength imbalance had significantly reduced concentric and eccentric bilateral hamstring peak torque ratios at all angular velocities tested; and reduced eccentric quadriceps peak torque (30°·s(-1)) in their stance leg, compared with those without strength imbalance. Approximately, 1 in 4 players had preseason hamstring strength imbalance; and all strength deficits were observed in the stance leg. Concentric and eccentric hamstrings strength imbalance may impact in-season football performance and could have implications for the future risk of injury.

Elevated temperature mechanical properties of line pipe steels

Science.gov (United States)

Jacobs, Taylor Roth

The effects of test temperature on the tensile properties of four line pipe steels were evaluated. The four materials include a ferrite-pearlite line pipe steel with a yield strength specification of 359 MPa (52 ksi) and three 485 MPa (70 ksi) yield strength acicular ferrite line pipe steels. Deformation behavior, ductility, strength, strain hardening rate, strain rate sensitivity, and fracture behavior were characterized at room temperature and in the temperature range of 200--350 °C, the potential operating range for steels used in oil production by the steam assisted gravity drainage process. Elevated temperature tensile testing was conducted on commercially produced as-received plates at engineering strain rates of 1.67 x 10 -4, 8.33 x 10-4, and 1.67 x 10-3 s-1. The acicular ferrite (X70) line pipe steels were also tested at elevated temperatures after aging at 200, 275, and 350 °C for 100 h under a tensile load of 419 MPa. The presence of serrated yielding depended on temperature and strain rate, and the upper bound of the temperature range where serrated yielding was observed was independent of microstructure between the ferrite-pearlite (X52) steel and the X70 steels. Serrated yielding was observed at intermediate temperatures and continuous plastic deformation was observed at room temperature and high temperatures. All steels exhibited a minimum in ductility as a function of temperature at testing conditions where serrated yielding was observed. At the higher temperatures (>275 °C) the X52 steel exhibited an increase in ductility with an increase in temperature and the X70 steels exhibited a maximum in ductility as a function of temperature. All steels exhibited a maximum in flow strength and average strain hardening rate as a function of temperature. The X52 steel exhibited maxima in flow strength and average strain hardening rate at lower temperatures than observed for the X70 steels. For all steels, the temperature where the maximum in both flow

Satisfaction with life and character strengths of nonreligious and religious people: it’s practicing one’s religion that makes the difference

Directory of Open Access Journals (Sweden)

Anne eBerthold

2014-08-01

Full Text Available According to systematic reviews, religious beliefs and practices are related to higher life satisfaction, happiness, and positive affect (Koenig & Larson, 2001. The present research extends previous findings by comparing satisfaction with life and character strengths of nonreligious people, religious people, who practice their religion and people that have a religious affiliation but do not practice their religion. We assessed life satisfaction (SWLS, character strengths (VIA-IS and the orientations to happiness (OTH in a sample of N=20538 participants. People with a religious affiliation that also practice their religion were found to be more satisfied with their life and scored higher on life of meaning than those who do not practice their religion and than nonreligious people. Also religious people who practice their religion differed significantly from those who do not practice their religion and nonreligious people regarding several character strengths; they scored higher on kindness, love, gratitude, hope, forgiveness, and on spirituality. There were no substantial differences between people who had no religious affiliation and those with a religious affiliation that do not practice their religion (all ηp2s < .009. Altogether, the present findings suggest that people profit from a religious affiliation if they also actively practice their religion.

Geotechnical properties of surface sediments in the INDEX area

Digital Repository Service at National Institute of Oceanography (India)

Khadge, N.H.

As a part of the environmental impact assessment studies, geotechnical properties of sediments were determined in the Central Indian Basin. The undrained shear strength and index properties of the siliceous sediments were determined on 20 box cores...

EJSCREEN Supplementary Indexes 2015 Public

Data.gov (United States)

U.S. Environmental Protection Agency — There are 40 supplementary EJSCREEN indexes that are divided into 5 categories: EJ Index with supplementary demographic index, Supplementary EJ Index 1 with...

Beta strength distributions in neutron-deficient Kr and Sr isotopes using a total absorption spectrometer

CERN Document Server

Maréchal, F

2003-01-01

Far from the line of stability, beta -decay studies are often a primary source of information on nuclear structure. The measured beta -strength distribution for a given decay can be used to verify the accuracy of our theoretical description of the parent nucleus ground state and the states populated in the daughter nucleus. Total absorption spectrometers based on large NaI crystals are well suited tools to determine the beta -strength distribution over the whole Q /sub EC/ decay window. The newly built spectrometer TAgS, dedicated to such studies, is presented and its performances and possibilities are discussed in the light of experiments performed at the ISOLDE /CERN mass separator. The resulting information on ground state deformations for the /sup 74/Kr and /sup 76/Sr isotopes are discussed. (22 refs).

Using the Maturity Method in Predicting the Compressive Strength of Vinyl Ester Polymer Concrete at an Early Age

Directory of Open Access Journals (Sweden)

Nan Ji Jin

2017-01-01

Full Text Available The compressive strength of vinyl ester polymer concrete is predicted using the maturity method. The compressive strength rapidly increased until the curing age of 24 hrs and thereafter slowly increased until the curing age of 72 hrs. As the MMA content increased, the compressive strength decreased. Furthermore, as the curing temperature decreased, compressive strength decreased. For vinyl ester polymer concrete, datum temperature, ranging from −22.5 to −24.6°C, decreased as the MMA content increased. The maturity index equation for cement concrete cannot be applied to polymer concrete and the maturity of vinyl ester polymer concrete can only be estimated through control of the time interval Δt. Thus, this study introduced a suitable scaled-down factor (n for the determination of polymer concrete’s maturity, and a factor of 0.3 was the most suitable. Also, the DR-HILL compressive strength prediction model was determined as applicable to vinyl ester polymer concrete among the dose-response models. For the parameters of the prediction model, applying the parameters by combining all data obtained from the three different amounts of MMA content was deemed acceptable. The study results could be useful for the quality control of vinyl ester polymer concrete and nondestructive prediction of early age strength.

Heart rate variability reflects self-regulatory strength, effort, and fatigue.

Science.gov (United States)

Segerstrom, Suzanne C; Nes, Lise Solberg

2007-03-01

Experimental research reliably demonstrates that self-regulatory deficits are a consequence of prior self-regulatory effort. However, in naturalistic settings, although people know that they are sometimes vulnerable to saying, eating, or doing the wrong thing, they cannot accurately gauge their capacity to self-regulate at any given time. Because self-regulation and autonomic regulation colocalize in the brain, an autonomic measure, heart rate variability (HRV), could provide an index of self-regulatory strength and activity. During an experimental manipulation of self-regulation (eating carrots or cookies), HRV was elevated during high self-regulatory effort (eat carrots, resist cookies) compared with low self-regulatory effort (eat cookies, resist carrots). The experimental manipulation and higher HRV at baseline independently predicted persistence at a subsequent anagram task. HRV appears to index self-regulatory strength and effort, making it possible to study these phenomena in the field as well as the lab.

Comparison of Off-Line IR Bump and Action-Angle Kick Minimization

CERN Document Server

Luo, Yun; Ptitsyn, Vadim; Trbojevic, Dejan; Wei, Jie

2005-01-01

The interaction region bump (IR bump) nonlinear correction method has been used for the sextupole and octupole field error on-line corrections in the Relativistic Heavy Ion Collider (RHIC). Some differences were found for the sextupole and octupole corrector strengths between the on-line IR bump correction and the predictions from the action-angle kick minimization. In this report we compare the corrector strengths from these two methods based on the RHIC Blue ring lattice with the IR nonlinear modeling. The comparison confirms the differences between resulting corrector strengths. And the reason for the differences is found and discussed. It is followed by a further discussion of the operational IR bump applications to the octupole, and skew sextupole and skew quadrupole field error corrections.

Elsevier’s CiteScore index values for Acta Dermatovenerologica Alpina, Pannonica et Adriatica: a 2016 update

Science.gov (United States)

Šterbenc, Anja; Oštrbenk, Anja

2017-09-01

Elsevier’s recently launched citation metric CiteScore enables comprehensive, transparent, and current evaluation of a journal’s performance. For an editorial office, insight into a journal’s impact over time is of great value when making important decisions regarding the journal’s future. A 2016 update of CiteScore index values for Acta Dermatovenerologica Alpina, Pannonica et Adri- atica (Acta Dermatovenerol APA) showed a slight decrease in the CiteScore index value from 1.18 in 2015 to 0.96 in 2016. Acta Dermatovenerol APA can still be considered the principal journal in the field of dermatology and sexually transmitted infections in our region, with almost half of the articles published between 2013 and 2015 cited at least once in 2016. Acta Dermatovenerol APA performed well in both categories listed because it ranked 67th out of 121 journals in the category Dermatology (44th percentile) and 175th out of 250 journals in the category Infectious Diseases (30th percentile).

[Electrical acupoint stimulation increases athletes' rapid strength].

Science.gov (United States)

Yang, Hua-yuan; Liu, Tang-yi; Kuai, Le; Gao, Ming

2006-05-01

To search for a stimulation method for increasing athletes' performance. One hundred and fifty athletes were randomly divided into a trial group and a control group, 75 athletes in each group. Acupoints were stimulated with audio frequency pulse modulated wave and multi-blind method were used to investigate effects of the electric stimulation of acupoints on 30-meter running, standing long jumping and Cybex isokinetic testing index. The acupoint electric stimulation method could significantly increase athlete's performance (P < 0.05), and the biomechanical indexes, maximal peak moment of force (P < 0.05), force moment accelerating energy (P < 0.05) and average power (P < 0.05). Electrical acupoint stimulation can enhance athlete's rapid strength.

Shear strength of non-shear reinforced concrete elements

DEFF Research Database (Denmark)

Hoang, Cao linh

1997-01-01

is based upon the hypothesis that cracks can be transformed into yield lines, which have lower sliding resistance than yield lines formed in uncracked concrete.Proposals have been made on how the derived standard solutions may be applied to more complicated cases, such as continuous beams, beams......The report deals with the shear strength of statically indeterminate reinforced concrete beams without shear reinforcement. Solutions for a number of beams with different load and support conditions have been derived by means of the crack sliding model developed by Jin- Ping Zhang.This model...

A Reliable and Valid Survey to Predict a Patient’s Gagging Intensity

Directory of Open Access Journals (Sweden)

Casey M. Hearing

2014-07-01

Full Text Available Objectives: The aim of this study was to devise a reliable and valid survey to predict the intensity of someone’s gag reflex. Material and Methods: A 10-question Predictive Gagging Survey was created, refined, and tested on 59 undergraduate participants. The questions focused on risk factors and experiences that would indicate the presence and strength of someone’s gag reflex. Reliability was assessed by administering the survey to a group of 17 participants twice, with 3 weeks separating the two administrations. Finally, the survey was given to 25 dental patients. In these cases, patients completed an informed consent form, filled out the survey, and then had a maxillary impression taken while their gagging response was quantified from 1 to 5 on the Fiske and Dickinson Gagging Intensity Index. Results: There was a moderate positive correlation between the Predictive Gagging Survey and Fiske and Dickinson’s Gagging Severity Index, r = +0.64, demonstrating the survey’s validity. Furthermore, the test-retest reliability was r = +0.96, demonstrating the survey’s reliability. Conclusions: The Predictive Gagging Survey is a 10-question survey about gag-related experiences and behaviours. We established that it is a reliable and valid method to assess the strength of someone’s gag reflex.

Reineke’s stand density index: a quantitative and non-unitless measure of stand density

Science.gov (United States)

Curtis L. VanderSchaaf

2013-01-01

When used as a measure of relative density, Reineke’s stand density index (SDI) can be made unitless by relating the current SDI to a standard density but when used as a quantitative measure of stand density SDI is not unitless. Reineke’s SDI relates the current stand density to an equivalent number of trees per unit area in a stand with a quadratic mean diameter (Dq)...

Wilson lines for AdS5 black strings

International Nuclear Information System (INIS)

Hristov, Kiril; Katmadas, Stefanos

2015-01-01

We describe a simple method of extending AdS 5 black string solutions of 5d gauged supergravity in a supersymmetric way by addition of Wilson lines along a circular direction in space. When this direction is chosen along the string, and due to the specific form of 5d supergravity that features Chern-Simons terms, the existence of magnetic charges automatically generates conserved electric charges in a 5d analogue of the Witten effect. Therefore we find a rather generic, model-independent way of adding electric charges to already existing solutions with no backreaction from the geometry or breaking of any symmetry. We use this method to explicitly write down more general versions of the Benini-Bobev black strings (http://dx.doi.org/10.1103/PhysRevLett.110.061601, http://dx.doi.org/10.1007/JHEP06(2013)005) and comment on the implications for the dual field theory and the similarities with generalizations of the Cacciatori-Klemm black holes (http://dx.doi.org/10.1007/JHEP01(2010)085) in AdS 4 .

[Correlations Between Joint Proprioception, Muscle Strength, and Functional Ability in Patients with Knee Osteoarthritis].

Science.gov (United States)

Chen, Yoa; Yu, Yong; He, Cheng-qi

2015-11-01

To establish correlations between joint proprioception, muscle flexion and extension peak torque, and functional ability in patients with knee osteoarthritis (OA). Fifty-six patients with symptomatic knee OA were recruited in this study. Both proprioceptive acuity and muscle strength were measured using the isomed-2000 isokinetic dynamometer. Proprioceptive acuity was evaluated by establishing the joint motion detection threshold (JMDT). Muscle strength was evaluated by Max torque (Nm) and Max torque/weight (Nm/ kg). Functional ability was assessed by the Western Ontario and McMaster Universities Osteoarthritis Index physical function (WOMAC-PF) questionnaire. Correlational analyses were performed between proprioception, muscle strength, and functional ability. A multiple stepwise regression model was established, with WOMAC-PF as dependent variable and patient age, body mass index (BMI), visual analogue scale (VAS)-score, mean grade for Kellgren-Lawrance of both knees, mean strength for quadriceps and hamstring muscles of both knees, and mean JMDT of both knees as independent variables. Poor proprioception (high JMDT) was negatively correlated with muscle strength (Pcoefficient (B) = 0.385, P<0.50 and high VAS-scale score (B=0.347, P<0.05) were significant predictors of WOMAC-PF score. Patients with poor proprioception is associated with poor muscle strength and limitation in functional ability. Patients with symptomatic OA of knees commonly endure with moderate to considerable dysfunction, which is associated with poor proprioception (high JMDT) and high VAS-scale score.

Human Use Index

Data.gov (United States)

U.S. Environmental Protection Agency — Human land uses may have major impacts on ecosystems, affecting biodiversity, habitat, air and water quality. The human use index (also known as U-index) is the...

Optics calculations and beam line design for the JANNuS facility in Orsay

International Nuclear Information System (INIS)

Chauvin, N.; Henry, S.; Flocard, H.; Fortuna, F.; Kaitasov, O.; Pariset, P.; Pellegrino, S.; Ruault, M.O.; Serruys, Y.; Trocelier, P.

2007-01-01

JANNuS (Joint Accelerators for Nano-Science and Nuclear Simulation) will be a unique user facility in Europe dedicated to material modification by ion beam implantation and irradiation. The main originality of the project is that it will be possible to perform implantation and irradiation with simultaneous multiple ions beams and in situ characterization by transmission electron microscopy (TEM) observation or ion beam analysis. This facility will be composed of two experimental platforms located in two sites: the CEA-SRMP in Saclay and the CNRS-CSNSM in Orsay. This paper will focus on the design of two new transport beam lines for the Orsay site. One of the most challenging parts of the JANNuS project (Orsay site) is to design two new beam lines in order to inject, into a 200 kV TEM, two different ion beams (low and medium energy) coming from two existing pieces of equipment: a 2 MV Tandem accelerator and a 190 kV ion implanter. For these new beam lines, first order beam calculations have been done using transfer matrix formalism. A genetic algorithm has been written and adapted to perform the optimization of the beam line parameters. Then, using the SIMION code, field maps of the electrostatic elements (quadrupoles, spherical sectors) have been calculated and ion trajectories have been simulated. We studied specifically the optical aberrations induced by the electrostatic spherical deflectors. Finally, the results of the first order calculations and the field map simulations show a good agreement

Walkability Index

Data.gov (United States)

U.S. Environmental Protection Agency — The Walkability Index dataset characterizes every Census 2010 block group in the U.S. based on its relative walkability. Walkability depends upon characteristics of...

Model Complexity and Out-of-Sample Performance: Evidence from S&P 500 Index Returns

NARCIS (Netherlands)

Kaeck, Andreas; Rodrigues, Paulo; Seeger, Norman J.

We apply a range of out-of-sample specification tests to more than forty competing stochastic volatility models to address how model complexity affects out-of-sample performance. Using daily S&P 500 index returns, model confidence set estimations provide strong evidence that the most important model

The F309S mutation increases factor VIII secretion in human cell line

Directory of Open Access Journals (Sweden)

Daianne Maciely Carvalho Fantacini

2016-06-01

Full Text Available ABSTRACT OBJECTIVES: The capacity of a human cell line to secrete recombinant factor VIII with a F309S point mutation was investigated, as was the effect of the addition of chemical chaperones (betaine and sodium-4-phenylbutyrate on the secretion of factor VIII. METHODS: This work used a vector with a F309S mutation in the A1 domain to investigate FVIII production in the HEK 293 human cell line. Factor VIII activity was measured by chromogenic assay. Furthermore, the effects of chemical drugs on the culture were evaluated. RESULTS: The addition of the F309S mutation to a previously described FVIII variant increased FVIII secretion by 4.5 fold. Moreover, the addition of betaine or sodium-4-phenylbutyrate increased the secretion rate of FVIIIΔB proteins in HEK 293 cells, but the same effect was not seen for FVIIIΔB-F309S indicating that all the recombinant protein produced had been efficiently secreted. CONCLUSION: Bioengineering factor VIII expressed in human cells may lead to an efficient production of recombinant factor VIII and contribute toward low-cost coagulation factor replacement therapy for hemophilia A. FVIII-F309S produced in human cells can be effective in vivo.

Prestressed Concrete-Lined Pressure Tunnels : Towards Improved Safety and Economical Design

NARCIS (Netherlands)

Simanjuntak, Y.

2015-01-01

Pressure tunnels for hydropower plants are relatively expensive constructions, particularly when steel linings are used. Concrete linings can be economically attractive; however, their applicability is limited by the low tensile strength of concrete. Techniques to improve the bearing capacity of

AISI/DOE Advanced Process Control Program Vol. 4 of 6: ON-LINE, NON-DESTRUCTIVE MECHANICAL PROPERTY MEASUREMENT USING LASER-ULTRASOUND

Energy Technology Data Exchange (ETDEWEB)

Andre' Moreau; Martin Lord; Daniel Levesqure; Marc Dubois; Jean Bussiere; Jean-Pierre Monchalin; Christian Padioleau; Guy Lamouche; Teodor Veres; Martin Viens; Harold Hebert; Pierre Basseras; Cheng-Kuei Jen

2001-03-31

The goal of this project was to demonstrate the feasibility to measure the mechanical properties, such as yield strength, tensile strength, elongation, strain hardening exponent and plastic strain ratio parameters, of low carbon steel sheets on the production line using laser ultrasound. The ultrasound generated by the developed apparatus travels mostly back and forth in the thickness of the steel sheet. By measuring the time delay between two echoes, and the relative amplitude of these two echoes, one can measure ultrasound velocity and attenuation. These are governed by the microstructure: grain size, crystallographic texture, dislocations, etc. Thus, by recording the time behavior of the ultrasonic signal, one can extract microstructural information. These microstructural information together with the modified Hall-Petch equation allow measurement of the mechanical properties. Through laboratory investigations with a laboratory laser ultrasound system, followed by the installation of a prototype system at LTV Steel Company's No.1 Inspection Line in Cleveland, all target mechanical properties of ultra low carbon (ULC), low carbon (LC) and high strength low alloy (HSLA) steel sample lots were measured meeting or nearly meeting all the target accuracies. Thus, the project realized its goal to demonstrate that the mechanical properties of low carbon steel sheets can be measured on-line using laser ultrasound

Burst strength of tubing and casing based on twin shear unified strength theory.

Science.gov (United States)

Lin, Yuanhua; Deng, Kuanhai; Sun, Yongxing; Zeng, Dezhi; Liu, Wanying; Kong, Xiangwei; Singh, Ambrish

2014-01-01

The internal pressure strength of tubing and casing often cannot satisfy the design requirements in high pressure, high temperature and high H2S gas wells. Also, the practical safety coefficient of some wells is lower than the design standard according to the current API 5C3 standard, which brings some perplexity to the design. The ISO 10400: 2007 provides the model which can calculate the burst strength of tubing and casing better than API 5C3 standard, but the calculation accuracy is not desirable because about 50 percent predictive values are remarkably higher than real burst values. So, for the sake of improving strength design of tubing and casing, this paper deduces the plastic limit pressure of tubing and casing under internal pressure by applying the twin shear unified strength theory. According to the research of the influence rule of yield-to-tensile strength ratio and mechanical properties on the burst strength of tubing and casing, the more precise calculation model of tubing-casing's burst strength has been established with material hardening and intermediate principal stress. Numerical and experimental comparisons show that the new burst strength model is much closer to the real burst values than that of other models. The research results provide an important reference to optimize the tubing and casing design of deep and ultra-deep wells.

Evaluation of oscillator strength in colloidal CdSe/CdS dots-in-rods

Energy Technology Data Exchange (ETDEWEB)

Pisanello, Ferruccio [Universite Pierre et Marie Curie, Laboratoire Kastler Brossel, CNRS UMR8552, Ecole Normale Superieure, 4 place Jussieu, 75005 Paris (France); National Nanotechnology Laboratory of CNR/INFM, Scuola superiore ISUFI, Universita del Salento, 16 Via Arnesano, 73100 Lecce (Italy); Lemenager, Godefroy; Spinicelli, Piernicola; Amo, Alberto; Giacobino, Elisabeth; Bramati, Alberto [Universite Pierre et Marie Curie, Laboratoire Kastler Brossel, CNRS UMR8552, Ecole Normale Superieure, 4 place Jussieu, 75005 Paris (France); Martiradonna, Luigi [Istituto Italiano di Tecnologia (IIT), Center for Bio-Molecular Nanotechnolgy, Via Barsanti 1, Arnesano, 73010 Lecce (Italy); Fiore, Angela [National Nanotechnology Laboratory of CNR/INFM, Scuola superiore ISUFI, Universita del Salento, 16 Via Arnesano, 73100 Lecce (Italy); Cingolani, Roberto; De Vittorio, Massimo [National Nanotechnology Laboratory of CNR/INFM, Scuola superiore ISUFI, Universita del Salento, 16 Via Arnesano, 73100 Lecce (Italy); Istituto Italiano di Tecnologia (IIT), Center for Bio-Molecular Nanotechnolgy, Via Barsanti 1, Arnesano, 73010 Lecce (Italy)

2010-11-15

The oscillator strength in CdSe/CdS colloidal dot-in-rods is evaluated and assessed to be of {proportional_to}1.5. On the basis of this finding, the possibility to reach the strong coupling regime with photonic crystals nanocavities is discussed. In spite that carefully choosing the cavity parameters the strong coupling regime could be analytically achieved at room temperature, theoretical considerations show that the typical Rabi doublet cannot be resolved. The work draws also a viable strategy toward the observation of the strong coupling at cryogenic temperatures. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Co-relationship between california bearing ratio and index properties of jamshoro soil

International Nuclear Information System (INIS)

Iqbal, F.; Kumar, A.; Murtaza, A.

2018-01-01

Subgrade is a most important part of a pavement structure, which should have a reasonable stiffness modulus and shear strength. CBR (California Bearing Ratio) test is performed to evaluate stiffness modulus and shear strength of subgrade soils. However, CBR test is laborious and time consuming, particularly when soil is highly plastic like Jamshoro soil. In order to overcome this limitation, it may be appropriate to correlate CBR value of soil with its index properties like grain size analysis, Atterberg limits, and compaction characteristics such as MDD (Maximum Dry Density) and OMC (Optimum Moisture Content). This paper expresses the correlations between CBR value of Jamshoro soil and its index properties. SLRA (Single Linear Regression Analysis) and MLRA(Multiple Linear Regression) based Models were utilized. It is seen that MLRA gave better correlations up to R2 of about 0.984. It is observed that the Soaked CBR value can be predicted with confidence from LL (Liquid Limit), PI (Plasticity Index) and percent finer while the un-soaked CBR value can be obtained from LL, plasticity index and MDD. (author)

ANALISIS GERAK ROBOT LINE TRACER DENGAN PROGRAM ARTIFICIAL INTELLEGENCE MENGGUNAKAN MICROCONTROLLER AT89S51

OpenAIRE

I Wayan Widhiada

2012-01-01

The research discussed about the work system of The Line Tracer Robot movement analysis, with using the AI program and assembler programming language. The tools that used are microcontroller type AT89S51, Meitan ASM 2005 Standard Edition version 1.00 as development tools and Meitan 2005 as the hardware tools modul. From the result of research, it can be known that The Line Tracer Robot with AI program is able to show differences, among the white as a based colour and black as a line colour. T...

The effect of welding line heat-affected-zone on the formability of tube hydroforming process

Science.gov (United States)

ChiuHuang, Cheng-Kai; Hsu, Cheng-En; Lee, Ping-Kun

2016-08-01

Tube hydroforming has been used as a lightweight design approach to reduce CO2 emission for the automotive industry. For the high strength steel tube, the strength and quality of the welding line is very important for a successful tube hydroforming process. This paper aims to investigate the effect of the welding line's strength and the width of the heat-affected zone on the tube thinning during the hydroforming process. The simulation results show that both factors play an important role on the thickness distribution during the tube expansion.

The effect of welding line heat-affected-zone on the formability of tube hydroforming process

International Nuclear Information System (INIS)

ChiuHuang, Cheng-Kai; Hsu, Cheng-En; Lee, Ping-Kun

2016-01-01

Tube hydroforming has been used as a lightweight design approach to reduce CO_2 emission for the automotive industry. For the high strength steel tube, the strength and quality of the welding line is very important for a successful tube hydroforming process. This paper aims to investigate the effect of the welding line's strength and the width of the heat-affected zone on the tube thinning during the hydroforming process. The simulation results show that both factors play an important role on the thickness distribution during the tube expansion. (paper)

Absolute photoabsorption cross-sections (oscillator strengths) for hydrogen chloride, hydrogen bromide and hydrogen iodide

International Nuclear Information System (INIS)

Brion, C.E.; Dyck, M.; Cooper, G.

2004-01-01

Full text: Absolute photoabsorption cross-sections (oscillator strengths) for the free molecules HCl, HBr and HI have been measured in the valence and selected in- ner shell regions. The experimental technique used for these studies is dipole (e,e) spectroscopy [1-3] which is not affected by line saturation effects (i.e. bandwidth interactions) which can complicate direct photoabsorption methods using the Beer- Lambert law. The dipole (e,e) method is also not subject to the effects of higher order radiation. In the dipole (e,e) method relative intensities obtained in fast (3 keV) for- ward scattered electron energy loss spectra are converted to relative dipole oscillator strengths (i.e. photoabsorption spectra) using the known Bethe-Born factors for the instrument as a function of photon energy (i.e. energy loss). The target pressure is constant at 10 - 5 torr, but it is not necessary to know the absolute target density. The absolute oscillator strength scale for HCl is determined from Bethe-Born converted, wide range dipole (e,e) spectra using the Thomas-Reiche-Kuhn (TRK) sum rule. For HBr and HI the absolute oscillator strength scales have been established using the S(-2) Sum Rule and literature values of the static dipole polarizability

Detection of rock strength at Branisko massif

Directory of Open Access Journals (Sweden)

Lazarová Edita

2000-09-01

Full Text Available When monitoring and optimizing the driving proces of the exploratory gallery by a computer system, conditions for verification of the interaction between desintegrating head of driving machine and rock massif were created. One of the output values of this mathematical model is the model strength at a simple pressure ótlH, which is defined as a pressure at the discus and the massif contact during the desintigration (a near limit of massif strength. By geological and geological engineering exploration, the section of length 2340 m was divided into fourty-two geological sections and five quasi-homogeneous massif enviroments. In the article, results of scleroscopic strength óCI , the strength in a simple pressure determined from the point load test and the strength at simple pressure ótlH are confronted . The main advance of the electronic geomechanical monitoring is the density of gained information. The two-seconds sample period of input and output data during the driving process makes it possible to describe driving circumstances in an almost continual way for each millimeter of the built tunnel. Then the information about changes of disintegrated rock properties, have the same density (frequency. By comparing a quantity of data gained by examining the index of point strength, scleroscopic strength and the model strength in a simple pressure from the monitoring process of driving process it is obvious that during the driving of exploratory gallery of motorway tunnel Branisko, a proportion of data number from the three “type examinations” of strength was reached and it was approximately 1:7:5000. Approximately in the same proportion, there were determined values for the 42 geologic sections (I. – XLII., which were defined in detail by the geologic, engineering geologic, hydrogeologic and geotechnic research.. The presented quantity values of presented rock mass strength for each geologic section are presented by their arithmetic average

The Westerlund-Olander sample of S stars in the southern Milky Way

International Nuclear Information System (INIS)

Evans, T.L.; Catchpole, R.M.

1989-01-01

Infrared (JHKL) photometry and spectroscopy (5200-7700 A, 6 A resolution) is given for 72 stars classed as type S by Westerlund and Olander. There are 38 S stars, 26 M stars, of which most are supergiants, and eight stars without prominent absorption bands. The S stars are predominantly of the nearly pure S type (S index ∼ 6) and represent a substantial addition to the known sample of such stars. Several probable Mira variables and three stars with strong Li I 6707 A are included. A wide range in LaO strength for stars of similar temperature and ZrO strength may result from differing ratios of heavy to light s-process elements. A possible dependence of Na D strength on luminosity is found. The galactic distribution of the S stars is not significantly different from that of carbon stars in the same field, excluding the suggestion that these S stars are of much higher mass than carbon stars. The infrared colours, taken in conjunction with IRAS data, reveal heavy interstellar reddening as well as circumstellar shells around many stars of all three groups. One of the bandless stars, WO48, has a particularly extensive shell. (author)

The Associations between Pain Sensitivity and Knee Muscle Strength in Healthy Volunteers

DEFF Research Database (Denmark)

Henriksen, Marius; Klokker, Louise; Bartholdy, Cecilie

2013-01-01

lateralis, deltoid, and infrapatellar fat pad. Quadriceps and hamstring muscle strength was assessed isometrically at 60-degree knee flexion using a dynamometer. Associations between pain sensitivity and muscle strength were investigated using multiple regressions including age, gender, and body mass index...... as covariates. Results. Knee extension strength was associated with computer-controlled PPT on the vastus lateralis muscle. Computer-controlled PPTs were significantly correlated between sites (r > 0.72) and with cuff PPT (r > 0.4). Saline induced pain intensity and duration were correlated between sites (r > 0......Objectives. To investigate associations between muscle strength and pain sensitivity among healthy volunteers and associations between different pain sensitivity measures. Methods. Twenty-eight healthy volunteers (21 females) participated. Pressure pain thresholds (PPTs) were obtained from 1...

At-home resistance tubing strength training increases shoulder strength in the trained and untrained limb.

Science.gov (United States)

Magnus, C R A; Boychuk, K; Kim, S Y; Farthing, J P

2014-06-01

The purpose was to determine if an at-home resistance tubing strength training program on one shoulder (that is commonly used in rehabilitation settings) would produce increases in strength in the trained and untrained shoulders via cross-education. Twenty-three participants were randomized to TRAIN (strength-trained one shoulder; n = 13) or CONTROL (no intervention; n = 10). Strength training was completed at home using resistance tubing and consisted of maximal shoulder external rotation, internal rotation, scaption, retraction, and flexion 3 days/week for 4 weeks. Strength was measured via handheld dynamometry and muscle size measured via ultrasound. For external rotation strength, the trained (10.9 ± 10.9%) and untrained (12.7 ± 9.6%) arm of TRAIN was significantly different than CONTROL (1.6 ± 13.2%; -2.7 ± 12.3%; pooled across arm; P tubing training program on one limb can produce increases in strength in both limbs, and has implications for rehabilitation after unilateral shoulder injuries. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Infliximab treatment reduces tensile strength in intestinal anastomosis

DEFF Research Database (Denmark)

Jensen, Jonas Sanberg; Petersen, Nacie Bello; Biagini, Matteo

2015-01-01

:1) to receive either repeated IFX treatment or placebo. On day 15, three separate end-to-end anastomoses were performed on the jejunum. On postoperative day 5, tensile strength and bursting pressure for the anastomoses were tested and histologic changes examined. RESULTS: We found a significantly reduced...... as number of sutures in the tested anastomosis (coefficient = 0.51; P = 0.024). The general histologic score was significantly higher in the placebo group (5.00 +/- 1.26 versus 3.31 +/- 1.65, P = 0.03). CONCLUSIONS: Repeated high-dose IFX treatment reduces tensile strength significantly in rabbits...... effect on the healing process in intestinal anastomosis. The objective of this study was to examine the effect of repeated IFX treatment on anastomotic strength and degree of inflammation in the anastomotic line in the small intestine of rabbits. METHODS: Thirty-two rabbits were randomized (2...

150 Mb/s wifi transmission over 50m large core diameter step index POF

NARCIS (Netherlands)

Shi, Y.; Nieto Munoz, M.; Okonkwo, C.M.; Boom, van den H.P.A.; Tangdiongga, E.; Koonen, A.M.J.

2011-01-01

We demonstrate successful transmission of WiFi signals over 50m step-index plastic optical fibre with 1mm core diameter employing an eye-safe resonant cavity light emitting diode and an avalanche photodetector. The EVM performance of 4.1% at signal data rate of 150Mb/s is achieved.

Measures of Functional Performance and Their Association With Hip and Thigh Strength

Science.gov (United States)

Kollock, Roger; Van Lunen, Bonnie L.; Ringleb, Stacie I.; Oñate, James A.

2015-01-01

Context: Insufficient hip and thigh strength may increase an athlete's susceptibility to injury. However, screening for strength deficits using isometric and isokinetic instrumentation may not be practical in all clinical scenarios. Objective: To determine if functional performance tests are valid indicators of hip and thigh strength. Design: Descriptive laboratory study. Setting: Research laboratory. Patients or Other Participants: Sixty-two recreationally athletic men (n = 30, age = 21.07 years, height = 173.84 cm, mass = 81.47 kg) and women (n = 32, age = 21.03 years, height = 168.77 cm, mass = 68.22 kg) participants were recruited. Intervention(s): During session 1, we measured isometric peak force and rate of force development for 8 lower extremity muscle groups, followed by an isometric endurance test. During session 2, participants performed functional performance tests. Main Outcome Measure(s): Peak force, rate of force development, fatigue index, hop distance (or height), work (joules), and number of hops performed during the 30-second lateral-hop test were assessed. The r values were squared to calculate r 2. We used Pearson correlations to evaluate the associations between functional performance and strength. Results: In men, the strongest relationship was observed between triple-hop work and hip-adductor peak force (r2 = 50, P ≤ .001). Triple-hop work also was related to hip-adductor (r2 = 38, P ≤ .01) and hip-flexor (r2 = 37, P ≤ .01) rate of force development. For women, the strongest relationships were between single-legged vertical-jump work and knee-flexor peak force (r2 = 0.44, P ≤ .01) and single-legged vertical-jump height and knee-flexor peak force (r2 = 0.42, P ≤ .01). Single-legged vertical-jump height also was related to knee-flexor rate of force development (r2 = 0.49, P ≤ .001). The 30-second lateral-hop test did not account for a significant portion of the variance in strength endurance. Conclusions: Hop tests alone did not

Condromalácia de patela: comparação entre os achados em aparelhos de RM de alto e baixo campo magnético Chondromalacia patellae: comparison of high-field strength versus low-field strength magnetic resonance imaging findings

Directory of Open Access Journals (Sweden)

Maxime Figueiredo de Oliveira Freire

2006-06-01

Full Text Available OBJETIVO: Comparar os aparelhos de ressonância magnética de baixo campo e de alto campo para estudo da cartilagem articular da patela. MATERIAIS E MÉTODOS: Foi realizado estudo usando as seqüências GRE 2D, GRE 3D, FSE T2 e STIR (baixo campo e TSE T2 SPIR. Cada seqüência foi analisada separadamente para o estudo da cartilagem, sem o conhecimento dos dados do paciente e do resultado das outras seqüências, sendo atribuído grau de lesão de 0 a 3 e descrita a sua localização. Os resultados de concordância e discordância foram analisados pelos testes de Kappa e McNemar. RESULTADOS: Na faceta medial houve baixas concordâncias e as discordâncias mostraram significativa superestimação. Na faceta lateral houve boas concordâncias e as discordâncias não foram significativas. No ápice houve boas concordâncias e as discordâncias mostraram significativa subestimação. CONCLUSÃO: A seqüência STIR teve a melhor concordância com a seqüência TSE T2 SPIR. Lesões de alto grau são mais bem caracterizadas pelas seqüências do aparelho de baixo campo. Áreas de aumento de sinal dificultam o estudo da cartilagem da faceta medial da patela no aparelho de baixo campo.OBJECTIVE: To compare the performance of low-field-strength and high-field-strength magnetic resonance imaging equipments for evaluation of the patella articular cartilage. MATERIALS AND METHODS: The study was developed using GRE 2D, GRE 3D, FSE T2, STIR sequences (low-field and TSE T2 SPIR sequence. Each sequence has been separately analyzed for evaluation of the cartilage without knowledge of other sequences results or any patients data; the lesion was assigned a grade from 0 to 3 and had its location defined. Agreement and disagreement results were analyzed by Kappa and McNemar tests. RESULTS: Medial facet has presented low agreement index and disagreements showed to be significantly overestimated. Lateral facet has presented a reasonable agreement index and disagreement

Line-breaking algorithm enhancement in inverse typesetting paradigma

Directory of Open Access Journals (Sweden)

Jan Přichystal

2007-01-01

Full Text Available High quality text preparing using computer desktop publishing systems usually uses line-breaking algorithm which cannot make provision for line heights and typeset paragraph accurately when composition width, page break, line index or other object appears. This article deals with enhancing of line-breaking algorithm based on optimum-fit algorithm. This algorithm is enhanced with calculation of immediate typesetting width and thus solves problem of forced change. Line-breaking algorithm enhancement causes expansion potentialities of high-quality typesetting in cases that have not been yet covered with present typesetting systems.

Midlife Healthy-Diet Index and Late-Life Dementia and Alzheimer’s Disease

Directory of Open Access Journals (Sweden)

Marjo H. Eskelinen

2011-04-01

Full Text Available Aim: To study long-term effects of dietary patterns on dementia and Alzheimer’s disease (AD. Methods: Of 525 subjects randomly selected from population-based cohorts surveyed at midlife, a total of 385 (73% subjects were re-examined 14 years later in the CAIDE study. A healthy-diet index (range 0–17 was constructed including both healthy and unhealthy dietary components. Results: Persons with a healthy diet (healthy-diet index >8 points had a decreased risk of dementia (OR 0.12, 95% CI 0.02–0.85 and AD (OR 0.08, 95% CI 0.01–0.89 compared with persons with an unhealthy diet (0–8 points, adjusting for several possible confounders. Conclusions: Healthy diet at midlife is associated with a decreased risk of dementia/AD in late life. These findings highlight the importance of dietary patterns and may make more effective measures for dementia/AD prevention or postponement possible.

Development of K-Basin High-Strength Homogeneous Sludge Simulants and Correlations Between Unconfined Compressive Strength and Shear Strength

Energy Technology Data Exchange (ETDEWEB)

Onishi, Yasuo; Baer, Ellen BK; Chun, Jaehun; Yokuda, Satoru T.; Schmidt, Andrew J.; Sande, Susan; Buchmiller, William C.

2011-02-20

potential for erosion, it is important to compare the measured shear strength to penetrometer measurements and to develop a correlation (or correlations) between UCS measured by a pocket penetrometer and direct shear strength measurements for various homogeneous and heterogeneous simulants. This study developed 11 homogeneous simulants, whose shear strengths vary from 4 to 170 kPa. With these simulants, we developed correlations between UCS measured by a Geotest E-280 pocket penetrometer and shear strength values measured by a Geonor H-60 hand-held vane tester and a more sophisticated bench-top unit, the Haake M5 rheometer. This was achieved with side-by-side measurements of the shear strength and UCS of the homogeneous simulants. The homogeneous simulants developed under this study consist of kaolin clay, plaster of Paris, and amorphous alumina CP-5 with water. The simulants also include modeling clay. The shear strength of most of these simulants is sensitive to various factors, including the simulant size, the intensity of mixing, and the curing time, even with given concentrations of simulant components. Table S.1 summarizes these 11 simulants and their shear strengths.

Relationship between Wiberg's lateral center edge angle, Lequesne's acetabular index, and medial acetabular bone stock

Energy Technology Data Exchange (ETDEWEB)

Werner, Clement M.L. [Balgrist University Hospital Zurich, Department of Orthopaedics, Zurich (Switzerland); University of Maryland Medical Systems, R. Adams Cowley Shock Trauma Center, Baltimore, MD (United States); Copeland, Carol E.; Stromberg, Jeff; Turen, Clifford H. [University of Maryland Medical Systems, R. Adams Cowley Shock Trauma Center, Baltimore, MD (United States); Ruckstuhl, Thomas; Bouaicha, Samy [Balgrist University Hospital Zurich, Department of Orthopaedics, Zurich (Switzerland)

2011-11-15

Knowledge of acetabular anatomy is crucial for cup positioning in total hip replacement. Medial wall thickness of the acetabulum is known to correlate with the degree of developmental dysplasia of the hip (DDH). No data exist about the relationship of routinely used radiographic parameters such as Wiberg's lateral center edge angle (LCE-angle) or Lequesne's acetabular index (AI) with thickness of the medial acetabular wall in the general population. The aim of our study was to clarify the relationship between LCE, AI, and thickness of the medial acetabular wall. Measurements on plain radiographs (LCE and AI) and axial CT scans (quadrilateral plate acetabular distance QPAD) of 1,201 individuals (2,402 hips) were obtained using a PACS imaging program and statistical analyses were performed. The mean thickness of the medial acetabulum bone stock (QPAD) was 1.08 mm (95% CI: 1.05-1.10) with a range of 0.1 to 8.8 mm. For pathological values of either the LCE (<20 ) or the AI (>12 ) the medial acetabular wall showed to be thicker than in radiological normal hips. The overall correlation between coxometric indices and medial acetabular was weak for LCE (r =-0.21. 95% CI [-0.25, -0.17]) and moderate for AI (r = 0.37, [0.33, 0.41]). We did not find a linear relationship between Wiberg's lateral center edge angle, Lequesne's acetabular index and medial acetabular bone stock in radiological normal hips but medial acetabular wall thickness increases with dysplastic indices. (orig.)

APPLICATION OF ALLOMETRY FOR DETERMINATION OF STRENGTH PROFILE IN YOUNG FEMALE ATHLETES FROM DIFFERENT SPORTS

Directory of Open Access Journals (Sweden)

J. Gajewski

2011-11-01

Full Text Available The goal of the study was to determine a strength profile in young female athletes practising different sports and to use allometry to evaluate muscular strength with respect to body mass. The study included 42 women who practised taekwondo (n = 10, weightlifting (n = 10, canoeing (n = 14 and speed skating (n = 8. Measurements of maximal muscle torques under static conditions in 10 groups of flexors and extensors of the elbow, shoulder, hip, knee and trunk were carried out. The MANCOVA procedure was employed to compare means between the groups. A logarithm of body mass was adopted as a covariate. Relationships between body mass and muscle torques in each muscle group were determined using a procedure of linear regression. The analysis of residuals was employed for the evaluation of maximal muscle torques. Mean values of logarithms of maximal muscle torques were significantly different for the representatives of individual sports and they depended on the logarithm of body mass. It was proposed to use a mean of residuals normalized for individual muscle groups as a synthetic strength index (mean of the strength profile. The women practising canoeing were characterized by the highest strength index. Its lowest values were obtained by weightlifting and taekwondo athletes. Differences in strength profiles in the tested athletes were attributed to the specific nature of their sports. It is suggested to use an allometric relationship scaled by body mass for strength assessment.

Evaluation of Changes in Index Properties of Lateritic Soil Stabilized with Fly Ash

Directory of Open Access Journals (Sweden)

Agapitus AMADI

2010-12-01

Full Text Available For soils to be suitable in civil engineering projects, they must meet existing local requirements for index properties in addition to certain strength criteria. Typically, specifications limit these properties to some threshold values which in most cases are project specific. Some lateritic soils in their natural state need some treatment/modification to meet these specification requirements. The objective of this study was to evaluate changes in the index properties (i.e., particle size distribution, Atterberg limits and compaction characteristics of a residually derived lateritic soil following fly ash application. Lateritic soil – fly ash mixtures with up to 20% fly ash by dry weight of soil were tested and specimens for compaction characteristics were prepared at different compaction states (optimum, dry and wet of optimum moisture content and compacted using British Standard Light (BSL compactive effort. While soil – fly ash mixtures containing up to 15% fly ash classify as CL according to USCS classification system and plotted above A-line in the plasticity chart, it was observed that changes in the gradation characteristics of soil sample treated with 20% fly ash resulted in the alteration of its classification to ML as well as the crossing of the A- line to the silty region. The liquid limit (LL varied from 42.2 to 29.53% representing 70% reduction while the plasticity index (PI of specimen treated with 20% fly ash was 16% lower than that of natural soil. The optimum moisture content (OMC ranged from 17.36% for the natural soil to 18.34% for soil mixtures containing 20% fly ash which yielded dry unit weight of 17.2kN/m3 for the natural soil and 16.1kN/m3 for samples treated with 20% fly ash. From the study, useful data were obtained showing substantial and desirable changes in the properties of lateritic soil as a civil engineering material on application of fly ash.

An image overall complexity evaluation method based on LSD line detection

Science.gov (United States)

Li, Jianan; Duan, Jin; Yang, Xu; Xiao, Bo

2017-04-01

In the artificial world, whether it is the city's traffic roads or engineering buildings contain a lot of linear features. Therefore, the research on the image complexity of linear information has become an important research direction in digital image processing field. This paper, by detecting the straight line information in the image and using the straight line as the parameter index, establishing the quantitative and accurate mathematics relationship. In this paper, we use LSD line detection algorithm which has good straight-line detection effect to detect the straight line, and divide the detected line by the expert consultation strategy. Then we use the neural network to carry on the weight training and get the weight coefficient of the index. The image complexity is calculated by the complexity calculation model. The experimental results show that the proposed method is effective. The number of straight lines in the image, the degree of dispersion, uniformity and so on will affect the complexity of the image.