WorldWideScience

Sample records for lignite fbc ash

  1. Cast-concrete products made with FBC ash and wet-collected coal-ash

    Energy Technology Data Exchange (ETDEWEB)

    Naik, T.R.; Kraus, R.N.; Chun, Y.M.; Botha, F.D. [University of Wisconsin, Milwaukee, WI (United States)

    2005-12-01

    Cast-concrete hollow blocks, solid blocks, and paving stones were produced at a manufacturing plant by replacing up to 45% (by mass) of portland cement with fluidized bed combustion (FBC) coal ash and up to 9% of natural aggregates with wet-collected, low-lime, coarse coal-ash (WA). Cast-concrete product specimens of all three types exceeded the compressive strength requirements of ASTM from early ages, with the exception of one paving-stone mixture, which fell short of the requirement by less than 10%. The cast-concrete products made by replacing up to 40% of cement with FBC ash were equivalent in strength (89-113% of control) to the products without ash. The abrasion resistance of paving stones was equivalent for up to 34% FBC ash content. Partial replacement of aggregates with WA decreased strength of the products. The resistance of hollow blocks and paving stones to freezing and thawing decreased appreciably with increasing ash contents. The cast-concrete products could be used indoors in regions where freezing and thawing is a concern, and outdoors in a moderate climate.

  2. Market Assessment and Demonstration of Lignite FBC Ash Flowable Fill Applications

    International Nuclear Information System (INIS)

    Alan E. Bland

    2003-01-01

    Montana-Dakota Utilities (MDU) and Western Research Institute (WRI) have been developing flowable fill materials formulated using ash from the Montana-Dakota Utilities R. M. Heskett Station in Mandan, North Dakota. MDU and WRI have partnered with the U.S. Department of Energy (DOE) and the North Dakota Industrial Commission (NDIC) to further the development of these materials for lignite-fired fluidized-bed combustion (FBC) facilities. The MDU controlled density fill (CDF) appears to be a viable engineering material and environmentally safe. WRI is pursuing the commercialization of the technology under the trademark Ready-Fill(trademark). The project objectives were to: (1) assess the market in the Bismarck-Mandan area; (2) evaluate the geotechnical properties and environmental compatibility; and (3) construct and monitor demonstrations of the various grades of flowable fill products in full-scale demonstrations. The scope of initial phase of work entailed the following: Task I--Assess Market for MDU Flowable Fill Products; Task II--Assess Geotechnical and Environmental Properties of MDU Flowable Fill Products; and Task III--Demonstrate and Monitor MDU Flowable Fill Products in Field-Scale Demonstrations. The results of these testing and demonstration activities proved the following: (1) The market assessment indicated that a market exists in the Bismarck-Mandan area for structural construction applications, such as sub-bases for residential and commercial businesses, and excavatable fill applications, such as gas line and utility trench filling. (2) The cost of the MDU flowable fill product must be lower than the current $35-$45/cubic yard price if it is to become a common construction material. Formulations using MDU ash and lower-cost sand alternatives offer that opportunity. An estimated market of 10,000 cubic yards of MDU flowable fill products could be realized if prices could be made competitive. (3) The geotechnical properties of the MDU ash-based flowable

  3. Market Assessment and Demonstration of Lignite FBC Ash Flowable Fill Applications

    Energy Technology Data Exchange (ETDEWEB)

    Alan E. Bland

    2003-09-30

    Montana-Dakota Utilities (MDU) and Western Research Institute (WRI) have been developing flowable fill materials formulated using ash from the Montana-Dakota Utilities R. M. Heskett Station in Mandan, North Dakota. MDU and WRI have partnered with the U.S. Department of Energy (DOE) and the North Dakota Industrial Commission (NDIC) to further the development of these materials for lignite-fired fluidized-bed combustion (FBC) facilities. The MDU controlled density fill (CDF) appears to be a viable engineering material and environmentally safe. WRI is pursuing the commercialization of the technology under the trademark Ready-Fill{trademark}. The project objectives were to: (1) assess the market in the Bismarck-Mandan area; (2) evaluate the geotechnical properties and environmental compatibility; and (3) construct and monitor demonstrations of the various grades of flowable fill products in full-scale demonstrations. The scope of initial phase of work entailed the following: Task I--Assess Market for MDU Flowable Fill Products; Task II--Assess Geotechnical and Environmental Properties of MDU Flowable Fill Products; and Task III--Demonstrate and Monitor MDU Flowable Fill Products in Field-Scale Demonstrations. The results of these testing and demonstration activities proved the following: (1) The market assessment indicated that a market exists in the Bismarck-Mandan area for structural construction applications, such as sub-bases for residential and commercial businesses, and excavatable fill applications, such as gas line and utility trench filling. (2) The cost of the MDU flowable fill product must be lower than the current $35-$45/cubic yard price if it is to become a common construction material. Formulations using MDU ash and lower-cost sand alternatives offer that opportunity. An estimated market of 10,000 cubic yards of MDU flowable fill products could be realized if prices could be made competitive. (3) The geotechnical properties of the MDU ash-based flowable

  4. Characterization of North American lignite fly ashes. II. XRD Mineralogy

    International Nuclear Information System (INIS)

    McCarthy, G.J.; Johansen, D.M.; Thedchanamoorthy, A.; Steinwand, S.J.; Swanson, K.D.

    1988-01-01

    X-ray powder diffraction has been used to determine the crystalline phase mineralogy in samples of fly ash from each of the lignite mining areas of North America. The characteristic phases of North Dakota lignite fly ashes were periclase, lime, merwinite and the sulfate phases anhydrite, thenardite and a sodalite-structure phase. Mullite was absent in these low-Al/sub 2/O/sub 3/ ashes. Montana lignite ash mineralogy had characteristics of ND lignite and MT subbituminous coal fly ashes; mullite and C/sub 3/A were present and the alkali sulfates were absent. Texas and Louisiana lignite fly ashes had the characteristic mineralogy of bituminous coal fly ash: quartz, mullite, ferrite-spinel (magnetite) and minor hematite. Even though their analytical CaO contents were 7-14%, all but one lacked crystalline CaO-containing phases. Lignite fly ashes from Saskatchewan were generally the least crystalline of those studied and had a mineralogy consisting of quartz, mullite, ferrite spinel and periclase. Quantitative XRD data were obtained. The position of the diffuse scattering maximum in the x-ray diffractograms was indicative of the glass composition of the lignite fly ash

  5. Ash content of lignites - radiometric analysis

    International Nuclear Information System (INIS)

    Leonhardt, J.; Thuemmel, H.W.

    1986-01-01

    The quality of lignites is governed by the ash content varying in dependence upon the geologic conditions. Setup and function of the radiometric devices being used for ash content analysis in the GDR are briefly described

  6. Ameliorative properties of lignite fly ash in reclaiming saline and alkali soils

    Energy Technology Data Exchange (ETDEWEB)

    Mahalingam, P K

    1973-08-01

    Statistical analysis of the yield of rice grain and straw reveals that there is a significant increase in the yield of grain and straw due to the application of lignite fly ash over controls and application of lignite fly ash either at 5 tons or 10 tons per acre was on par with gypsum application at 5 tons/acre. Maximum yield was recorded in treatment with 5 tons of daincha plus 5 tons of lignite fly ash per acre. This is due to the combined effect of green manure and lignite fly ash. 4 references, 3 tables.

  7. NOx PREDICTION FOR FBC BOILERS USING EMPIRICAL MODELS

    Directory of Open Access Journals (Sweden)

    Jiří Štefanica

    2014-02-01

    Full Text Available Reliable prediction of NOx emissions can provide useful information for boiler design and fuel selection. Recently used kinetic prediction models for FBC boilers are overly complex and require large computing capacity. Even so, there are many uncertainties in the case of FBC boilers. An empirical modeling approach for NOx prediction has been used exclusively for PCC boilers. No reference is available for modifying this method for FBC conditions. This paper presents possible advantages of empirical modeling based prediction of NOx emissions for FBC boilers, together with a discussion of its limitations. Empirical models are reviewed, and are applied to operation data from FBC boilers used for combusting Czech lignite coal or coal-biomass mixtures. Modifications to the model are proposed in accordance with theoretical knowledge and prediction accuracy.

  8. Radioactivity of Yatagan lignites and their ash

    International Nuclear Information System (INIS)

    Cicek, F.; Mustafaev, I.; Aliyev, C.

    2004-01-01

    Full text: One of harmful factor of Environmental impact of coal combustion is radiation pollution of Environment. The natural radioisotopes - uranium, thorium and potassium and products of their radioactive destruction contains of radionuclides. These radionuclides in composition of fly ash are thrown to atmosphere from coal combustion furnaces. The concentration of radioisotopes in composition of coals changes in the wide ranges: from 3 up to 520 Becquerel per kilogram (Bq/kg) for Uranium-238 and from 3 up to 320 Bq/kg for thorium-232. The radioactive pollution degree of environment depends on radioisotopes content of initial fuels. In this connection at the estimation of outlook and exploitation of coal mines it is necessary to determine of radioisotopes concentration in coals. That is why investigation of radioisotopes concentration of Turkish lignites has great importance. In this work the radionuclide content of Yatagan lignites and their ash, taken from Gekova thermal Electro station have been studied. The total radiation background generated by these samples was investigated by using of dosimeters 8P-5, CRP-88H, PYB-OIP. Radionuclides content of samples was determined in the Institute of Geology Azerbaijan national Academy of Sciences by using of highly sensitivity gamma-spectrometer CAPU-2, designed by Special Constructor Buro G eophysika . The plant allows to determine the radioisotopes content of solid and liquid samples with highly reliability. It has been established that in sample of lignite uranium content (on the radium equivalent) is 68 Bq/kg, potassium-149 Bq/kg and thorium is absent. The total radioactivity of lignite sample is 79,7 Bq/kg. In the ash sample uranium content is 266 Bq/kg, potassium-188 Bq/kg, and total activity reach to 300 Bq/kg. The possibility of application of purification erection for radionuclides from smoke gases of coal combustion is discussed

  9. Determination of ash-forming elements in lignite coal

    International Nuclear Information System (INIS)

    Wischnewski, C.; Werner, G.; Vogt, J.; Just, G.

    1990-01-01

    The most important methods are discussed suitable for the determination of ash-forming elements in coal. In this connection questions of the concentrations of elements in lignites, of the sample preparation, and of the selection of methods for the determination of ash-forming elements are addressed. Advantages and disadvantages of different analysis techniques are shown using concrete examples. (author)

  10. Steam gasification of Bulmer coal in the presence of lignite ash

    Energy Technology Data Exchange (ETDEWEB)

    Palmer, A.; Furimsky, E.

    1986-01-01

    Steam gasification of blends prepared from Balmer coal and the ash from combustion of Onakawana lignite was performed in a fixed bed reactor. The blends were prepared by co-slurrying followed by drying. In the presence of 20 wt% ash the gasification rate doubled at 830 and 930 C. Direct blending of coal and lignite resulted in an overall increase in carbon conversion at 830 C but had no effect at 930 C. 5 refs.

  11. Radiation doses of inhaled ash from the lignite power plants

    International Nuclear Information System (INIS)

    Boshevski, Tome; Pop-Jordanov, Jordan; Chaushevski, Anton

    1997-01-01

    The coal-fired thermal power plants in Macedonia use lignite obtained by surface mining. The lignite contains traces of thorium-232, uranium-238 and uranium-235, which are long-lived natural radioactive isotopes. After lignite combustion, the concentration of these isotopes in the ash is increased. Due to the long life of fossil materials, the decay products are basically grouped in three radioactive chains that are in a semi-steady state, resulting in equal activity of all isotopes from the chain. Among the members of each chain there are α and β emitters followed by γ quanta emitters. The energies of the α and β particles are important for determining the effective dose. The γ quanta provide information about the chain activity and isotope types. Gamma-spectroscopy studies of the ash samples from the power plants in the City of Bitola in Macedonia have confirmed the presence of several radioactive decay products from the uranium and thorium radioactive chains. Using measurements of the radioactivity of the ash in the Bitola region, the total dose from ash inhalation for the population in the Bitola region was calculated and presented in this paper. Also, analysis of the procedure for determining the maximum allowable dose from radioactive contamination of the environment, is described in this paper. (Original)

  12. Innovative approach to ash radioactivitiy and health impacts of lignite power plants

    Energy Technology Data Exchange (ETDEWEB)

    Bosevski, T.; Pop-Jordanova, N. [Macedonian Academy of Sciences and Arts, Skopje (Macedonia)

    1998-12-31

    In Macedonia nearly 90% of the present electricity production utilizes domestic low-calorie lignite, and this is likely to continue for the next few decades. Local and global environmental impacts of fossil fuel utilization are considered. Some innovative extensions to standard methodologies of environmental risk assessment and management are considered. They involve ash radioactivity and psychosomatic health impacts from lignite power plants. Two extensions are proposed: one comprising complete radioactive chains when determining committed effective dose from lignite ash; the other by including the psychosomatic diseases, such as peptic ulcer and arterial hypertension, due to chronic stress induced by power plants during normal operation. 7 refs., 2 figs., 3 tabs.

  13. Synergetic use of lignite fly ash and metallurgical converter slag in geopolymer concrete

    Directory of Open Access Journals (Sweden)

    Gábor Mucsi

    2014-08-01

    Full Text Available The application and utilization of the industrial wastes and by-products in the construction industry is a key issue from an environmental and economic point of view. The increased use of lignite has substantially increased the available quantities of lignite fired power plant fly ash, which can be mainly classified as class C fly ash. The utilization of such raw material however has some difficulties. In the present paper lignite fired power station fly ash and metallurgical converter slag were used for the production of geopolymer concrete. The fly ash was used as a geopolymer based binder material, and a converter slag as aggregate, thus created a geopolymer concrete which contains mainly industrial wastes. As preliminary test experimental series were carried out using andesite as aggregate. The optimal aggregate/binder ratio was determined. The effect of the amount of alkaline activator solution in the binder, the aggregate type on the geopolymer concretes’ compressive strength and density was investigated. Furthermore, the physical properties - freeze-thaw resistance and particle size distribution - of the applied aggregates were measured as well. As a result of the experiments it was found that physical properties of the andesite and converter slag aggregate was close. Therefore andesite can be replaced by converter slag in the concrete mixture. Additionally, geopolymer concrete with nearly 20 MPa compressive strength was produced from class C fly ash and converter slag.

  14. Catalytic effect of lignite ash on steam gasification of oil sand coke

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E.; Palmer, A.

    1986-06-16

    Steam gasification of Suncor and Syncrude cokes was carried out in the presence of ash obtained after burning Onakawana lignite. Catalytic effects of the ash were evident at 930 C whereas at 830 C little effect was observed. These observations were attributed to the combined actions of Ca- and Fe-containing species in the ash, in which the former neutralized the sulfur in the cokes to prevent poisoning of Fe oxides. 5 tabs., 5 figs., 15 refs.

  15. State and performance of on-stream ash content determination in lignite and black coal using 2-energy transmission technique

    International Nuclear Information System (INIS)

    Thuemmel, H.W.; Koerner, G.; Leonhardt, J.

    1986-01-01

    The total r.m.s. ash error of the 2-energy transmission on-stream ash gauges KRAS-2 (CIIRR, GDR) and SIROASH (Australia) are 4 weight percentage for raw lignite and 0.5 weight percentage for black coal, respectively. A detailed error analysis shows that this difference is due to the high water content and to strong variations in the ash composition of raw lignite. Both gauges show essentially the same radiometric performance. (author)

  16. Environmental assessment of remedial action at the inactive uraniferous lignite ashing sites at Belfield and Bowman, North Dakota

    International Nuclear Information System (INIS)

    1993-09-01

    The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 authorized the US Department of Energy (DOE) to perform remedial actions at Belfield and Bowman inactive lignite ashing sites in southwestern North Dakota to reduce the potential public health impacts from the residual radioactivity remaining at the sites. The US Environmental Protection Agency (EPA) promulgated standards (40 CFR 192) that contain measures to control the residual radioactive materials and other contaminated materials, and proposed standards to protect the groundwater from further degradation. Remedial action at the Belfield and Bowman sites must be performed in accordance with these standards and with the concurrence of the US Nuclear Regulatory Commission (NRC) and the state of North Dakota. The Belfield and Bowman designated sites were used by Union Carbide and Kerr-McGee, respectively, to process uraniferous lignite in the 1960s. Uranium-rich ash from rotary kiln processing of the lignite was loaded into rail cars and transported to uranium mills in Rifle, Colorado, and Ambrosia Lake, New Mexico, respectively. As a result of the ashing process, there is a total of 158,400 cubic yards (yd 3 ) [121,100 cubic meters (m 3 )] of radioactive ash-contaminated soils at the two sites. Windblown ash-contaminated soil covers an additional 21 acres (8.5 ha) around the site, which includes grazing land, wetlands, and a wooded habitat

  17. Mineralogy and microstructure of sintered lignite coal fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Marina Ilic; Christopher Cheeseman; Christopher Sollars; Jonathan Knight [Faculty of Technology and Metallurgy, Belgrade (Yugoslavia)

    2003-02-01

    Lignite coal fly ash from the 'Nikola Tesla' power plant in Yugoslavia has been characterised, milled, compacted and sintered to form monolithic ceramic materials. The effect of firing at temperatures between 1130 and 1190{sup o}C on the density, water accessible porosity, mineralogy and microstructure of sintered samples is reported. This class C fly ash has an initial average particle size of 82 {mu}m and contains siliceous glass together with the crystalline phases quartz, anorthite, gehlenite, hematite and mullite. Milling the ash to an average particle size of 5.6 m, compacting and firing at 1170{sup o}C for 1 h produces materials with densities similar to clay-based ceramics that exhibit low water absorption. Sintering reduces the amount of glass, quartz, gehlenite and anhydrite, but increases formation of anorthite, mullite, hematite and cristobalite. SEM confirms the formation of a dense ceramic at 1170{sup o}C and indicates that pyroplastic effects cause pore formation and bloating at 1190{sup o}C. 23 refs., 6 figs., 2 tabs.

  18. H-binding of size- and polarity-fractionated soil and lignite humic acids after removal of metal and ash components

    Science.gov (United States)

    Drosos, Marios; Leenheer, Jerry A.; Avgeropoulos, Apostolos; Deligiannakis, Yiannis

    2014-01-01

    A fractionation technique, combining dialysis removal of metal and ash components with hydrofluoric acid and pH 10 citrate buffer followed by chromatography of dialysis permeate on XAD-8 resin at decreasing pH values, has been applied to lignite humic acid (lignite-HA) and soil humic acid (soil-HA). H-binding data and non ideal competitive adsorption-Donnan model parameters were obtained for the HA fractions by theoretical analysis of H-binding data which reveal a significant increase of the carboxyl and the phenolic charge for the lignite-HA fractions vs. the parental lignite humic acid (LParentalHA). The fractionated lignite-HA material consisted mainly of permeate fractions, some of which were fulvic acid-like. The fractionated soil-HA material consisted mainly of large macromolecular structures that did not permeate the dialysis membrane during deashing. Chargeable groups had comparable concentrations in soil-HA fractions and parental soil humic acid (SParentalHA), indicating minimal interference of ash components with carboxyl and phenolic (and/or enolic) groups. Fractionation of HA, combined with theoretical analysis of H-binding, can distinguish the supramolecular vs. macromolecular nature of fractions within the same parental HA.

  19. Environmental considerations on the FBC combustion of dry sewage sludge

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, M. Helena; Abelha, Pedro; Gulyurtlu, Ibrahim; Cabrita, Isabel [INETI/DEECA, Lisboa (Portugal)

    2001-07-01

    This paper presents results of on-going research on the incineration of pre-dried granular sewage sludges using a FBC system. Co-combustion is compared with mono-combustion of sludges leads to minor emissions and higher retention of Cd, Pb, Cu, and Zn in the bottom ashes, when compared to co-combustion with coal. The leachability of the sludge is reduced through combustion, as none of the metals, Cd, Cr, Ca Ni, Ph, Zn, Co and Mn were leached from the bottom ashes. These findings may contribute to an improvement in the incineration of sewage sludges and to the development of applications for the ashes in civil engineering activities.

  20. Validation of a FBC model for co-firing of hazelnut shell with lignite against experimental data

    Energy Technology Data Exchange (ETDEWEB)

    Kulah, Gorkem [Middle East Technical University, Department of Chemical Engineering, 06531 Ankara (Turkey)

    2010-07-15

    Performance of a comprehensive system model extended for modelling of co-firing of lignite and biomass was assessed by applying it to METU 0.3 MW{sub t} Atmospheric Bubbling Fluidized Bed Combustor co-firing lignite with hazelnut shell and validating its predictions against on-line temperature and concentration measurements of O{sub 2}, CO{sub 2}, CO, SO{sub 2} and NO along the same test rig fired with lignite only, lignite with limestone addition and lignite with biomass and limestone addition. The system model accounts for hydrodynamics; volatiles release and combustion, char combustion, particle size distribution for lignite and biomass; entrainment; elutriation; sulfur retention and NO formation and reduction, and is based on conservation equations for energy and chemical species. Special attention was paid to different devolatilization characteristics of lignite and biomass. A volatiles release model based on a particle movement model and a devolatilization kinetic model were incorporated into the system model separately for both fuels. Kinetic parameters for devolatilization were determined via thermogravimetric analysis. Predicted and measured temperatures and concentrations of gaseous species along the combustor were found to be in good agreement. Introduction of biomass to lignite was found to decrease SO{sub 2} emissions but did not affect NO emissions significantly. The system model proposed in this study proves to be a useful tool in qualitatively and quantitatively simulating the processes taking place in a bubbling fluidized bed combustor burning lignite with biomass. (author)

  1. Using cement, lignite fly ash and baghouse filter waste for solidification of chromium electroplating treatment sludge

    Directory of Open Access Journals (Sweden)

    Wantawin, C.

    2004-02-01

    Full Text Available The objective of the study is to use baghouse filter waste as a binder mixed with cement and lignite fly ash to solidify sludge from chromium electroplating wastewater treatment. To save cost of solidification, reducing cement in binder and increasing sludge in the cube were focused on. Minimum percent cement in binder of 20 for solidification of chromium sludge was found when controlling lignite fly ash to baghouse filter waste at the ratio of 30:70, sludge to binder ratio of 0.5, water to mixer ratio of 0.3 and curing time of 7 days. Increase of sludge to binder ratio from 0.5 to 0.75 and 1 resulted in increase in the minimum percent cement in binder up to 30 percent in both ratios. With the minimum percent cement in binder, the calculated cement to sludge ratios for samples with sludge to binder ratios of 0.5, 0.75 and 1 were 0.4, 0.4 and 0.3 respectively. Leaching chromium and compressive strength of the samples with these ratios could achieve the solidified waste standard by the Ministry of Industry. For solidification of chromium sludge at sludge to binder ratio of 1, the lowest cost binder ratio of cement to lignite fly ash and baghouse filter waste in this study was 30:21:49. The cost of binder in this ratio was 718 baht per ton dry sludge.

  2. Fluidized bed combustion bottom ash: A better and alternative geo-material resource for construction.

    Science.gov (United States)

    Mandal, A K; Paramkusam, Bala Ramudu; Sinha, O P

    2018-04-01

    Though the majority of research on fly ash has proved its worth as a construction material, the utility of bottom ash is yet questionable due to its generation during the pulverized combustion process. The bottom ash produced during the fluidized bed combustion (FBC) process is attracting more attention due to the novelty of coal combustion technology. But, to establish its suitability as construction material, it is necessary to characterize it thoroughly with respect to the geotechnical as well as mineralogical points of view. For fulfilling these objectives, the present study mainly aims at characterizing the FBC bottom ash and its comparison with pulverized coal combustion (PCC) bottom ash, collected from the same origin of coal. Suitability of FBC bottom ash as a dike filter material in contrast to PCC bottom ash in replacing traditional filter material such as sand was also studied. The suitability criteria for utilization of both bottom ash and river sand as filter material on pond ash as a base material were evaluated, and both river sand and FBC bottom ash were found to be satisfactory. The study shows that FBC bottom ash is a better geo-material than PCC bottom ash, and it could be highly recommended as an alternative suitable filter material for constructing ash dikes in place of conventional sand.

  3. Natural radioisotopes in lignite of the Ptolemais region (Greece) and in their ashes

    International Nuclear Information System (INIS)

    Simopoulos, S.E.; Angelopoulos, M.G.

    1987-01-01

    Samples of lignite, fly ash and bottom ash of a power plant, located in the Ptolemais region, were examined by gamma spectroscopy and their concentrations in Ra-226, Ra-228 and K-40 have been determined. These samples were prepared from samples taken daily for a period of one month. The brown coal samples are taken from the front of the brown coal field supplying one of the units. They show a flutuation of the concentrations of the same radionuclides in the brown coal seams and in the intermediate layers. Further samples taken from 3 small private mines of the Ptolemais region were also examined. (author)

  4. Minimum emissions from biomass FBC. Improved energy generation based on biomass FBC with minimum emission. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hallgren, A. [TPS Termiska Processer AB, Nykoeping (Sweden)

    2002-02-01

    The primary aim of the project is to improve the performance of biomass fired FBC (fluidised bed combustion) through a concurrent detailed experimental and modelling approach. The expected results shall establish in experimental investigations, the thermochemical performance of a selection of fuels separately and in combination with suitable bed materials, stipulate recommendations, based on labscale via test rig and pilot scale to commercial scale investigations, how to repress agglomeration and defluidisation in fluidised bed combustion systems, indicate, based on the experimental findings, how to utilise primary measures to minimise the formation of nitrogen oxide compounds in the FB and provide a logistic assessment, based on case studies, identifying optimum logistic strategies for the selected fuels in commercial heat and power production. The investigation programme comprises straw, meat and bone meal (MBM) and forest residues as biofuels, quartz sand, bone ash, magnesium oxide and mullite as bed materials, sodium and ammonia carbonate as NO{sub x} reduction additives, and dolomite, kaolinite and coal ash for suppression of bed defluidisation. All materials have undergone a very detailed characterisation programme generating basic data on their chemical and structural composition as well as their sintering propensities. Combustion residues such as bottom and fly ashes have run through the same characterisation programme. The knowledge obtained by the characterisation programme supports the experimental combustion campaigns which are performed at 20, 90 and 350 kW FBC reactors. The information produced is validated in a 3 MW and 25 MW commercial FBC reactor. NO{sub x} formation and destruction mechanisms and rates have been included in a 3-D CFD software code used for NO{sub x} formation modelling. Parameter assessments confirmed the theoretical achievement of a 20-30 % reduction of NO{sub x} formation through implementation of the alkali injection concept as

  5. Effect of CaCO_3 addition on ash sintering behaviour during K_2CO_3 catalysed steam gasification of a Chinese lignite

    International Nuclear Information System (INIS)

    Zhang, Jiguang; Li, Jianbo; Mao, Yandong; Bi, Jicheng; Zhu, Mingming; Zhang, Zhezi; Zhang, Li; Zhang, Dongke

    2017-01-01

    Highlights: • K_2CO_3 decreased ash sintering temperature and enhanced ash melting in gasification. • CaCO_3 addition enhanced ash melting and lowered ash sintering temperatures. • CaCO_3 reacted with SiO_2 to form fluxing phases and amorphous materials. • CaCO_3 addition inhibited the potassium aluminium silicate formation. • CaCO_3 addition preserved the catalytic activity of potassium. - Abstract: The ash sintering behaviour of a Chinese lignite (LLI) with different amounts of CaCO_3 addition during K_2CO_3-catalysed gasification was investigated. 0–10 wt% K_2CO_3 was doped into the lignite for catalytic gasification, and CaCO_3 was added into the K_2CO_3-doped samples, varying in the range of 0–20 wt% relative to the lignite, for understanding its impact on ash sintering and catalytic gasification activity. Ash samples were prepared by completely gasifying the lignite samples with steam in a fixed-bed catalytic gasification system operating at 1073 K and atmospheric pressure. Sintering temperature, mineralogy and morphology of the ash samples thus obtained were determined using a pressure-drop sintering device, XRD and SEM-EDS, respectively. The results showed that the ash sintering temperature decreased as the K_2CO_3 addition increased, indicating that K_2CO_3 as the catalyst for gasification would promote ash sintering. SEM imaging analysis showed that all the ash samples from LLI with K_2CO_3 addition were composed of agglomerated particles with smooth surfaces, indicating the ashes had incurred partial melting. The degree of melting became more apparent as the K_2CO_3 addition ratio increased. These molten phases were identified as K-bearing arcanite and kaliophilite, which contributed to the formation of liquid phases at lower temperatures, resulting in lowered ash sintering temperatures. It was also revealed that the addition of CaCO_3 decreased the sintering temperatures of ash samples, indicating that the ash sintering was further

  6. Use of INAA for investigation of emission of elements in combustion of Polish lignite

    International Nuclear Information System (INIS)

    Janczyszyn, J.; Loska, L.; Pohorecki, W.; Wagner, M.

    2002-01-01

    Instrumental neutron activation analysis (INAA) has been applied for the determination of trace elements content in samples of Polish lignite and its ash. Pairs of results, for lignite and ash, and respective ash contents were used for calculation of the percentage of element remaining in ash after the lignite combustion. (author)

  7. Naturally occurring radioactive materials (NORMs) generated from lignite-fired power plants in Kosovo

    International Nuclear Information System (INIS)

    Hasani, F.; Shala, F.; Xhixha, G.; Xhixha, M.K.; Hodolli, G.; Kadiri, S.; Bylyku, E.; Cfarku, F.

    2014-01-01

    The energy production in Kosovo depends primarily on lignite-fired power plants. During coal combustion, huge amounts of fly ash and bottom ash are generated, which may result in enriched natural radionuclides; therefore, these radionuclides need to be investigated to identify the possible processes that may lead to the radiological exposure of workers and the local population. Lignite samples and NORMs of fly ash and bottom ash generated in lignite-fired power plants in Kosovo are analyzed using a gamma-ray spectrometry method for the activity concentration of natural radionuclides. The average activity concentrations of 40 K, 226 Ra and 232 Th in lignite are found to be 36 ± 8 Bq kg −1 , 9 ± 1 Bq kg −1 and 9 ± 3 Bq kg −1 , respectively. Indications on the occurrence and geochemical behavior of uranium in the lignite matrix are suggested. The activity concentrations of natural radionuclides in fly ash and bottom ash samples are found to be concentrated from 3 to 5 times that of the feeding lignite. The external gamma-ray absorbed dose rate and the activity concentration index are calculated to assess the radiological hazard arising from ash disposal and recycling in the cement industry. - Highlights: • NORMs in lignite combustion residues from CFPPs are studied. • Th/U indicates either low U uptake from host rocks and/or high leaching from peat. • The concentration factor of NORMs in fly and bottom ash samples are 3–5 times. • No 226 Ra enrichment is observed in fly ash while a depletion in bottom ash. • The reuse of fly ash in cement industry poses no significant radiological issue

  8. Naturally occurring radioactive materials (NORMs) generated from lignite-fired power plants in Kosovo.

    Science.gov (United States)

    Hasani, F; Shala, F; Xhixha, G; Xhixha, M K; Hodolli, G; Kadiri, S; Bylyku, E; Cfarku, F

    2014-12-01

    The energy production in Kosovo depends primarily on lignite-fired power plants. During coal combustion, huge amounts of fly ash and bottom ash are generated, which may result in enriched natural radionuclides; therefore, these radionuclides need to be investigated to identify the possible processes that may lead to the radiological exposure of workers and the local population. Lignite samples and NORMs of fly ash and bottom ash generated in lignite-fired power plants in Kosovo are analyzed using a gamma-ray spectrometry method for the activity concentration of natural radionuclides. The average activity concentrations of (40)K, (226)Ra and (232)Th in lignite are found to be 36 ± 8 Bq kg(-1), 9 ± 1 Bq kg(-1) and 9 ± 3 Bq kg(-1), respectively. Indications on the occurrence and geochemical behavior of uranium in the lignite matrix are suggested. The activity concentrations of natural radionuclides in fly ash and bottom ash samples are found to be concentrated from 3 to 5 times that of the feeding lignite. The external gamma-ray absorbed dose rate and the activity concentration index are calculated to assess the radiological hazard arising from ash disposal and recycling in the cement industry. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. Fluidized-bed-combustion ash for the solidification and stabilization of a metal-hydroxide sludge.

    Science.gov (United States)

    Knoll, K L; Behr-Andres, C

    1998-01-01

    Fluidized-bed-combustion (FBC) ash is a by-product from a developing technology for coal-fired power plants that will economically reduce air emissions to meet requirements of the Clean Air Act. FBC ash has physical and chemical properties similar to Portland cement, but only has moderate success as a pozzolan in concrete applications due to low compressive strengths. However, FBC ash has proven effective for use as a binder for the solidification and stabilization (S/S) of metal-bearing sludges. Physical and chemical characterization procedures were used to analyze FBC ash and a metal-bearing sludge obtained from a hazardous waste treatment facility to develop 12 different S/S mix designs. The mix designs consist of four binder designs to evaluate sludge-to-binder ratios of approximately 0, 0.5, and 1. Portland cement is used as a control binder to compare unconfined compressive strengths and Toxicity Characteristic Leaching Procedure (TCLP) analyses from different ratios of the FBC ash streams: fly ash, char, and spent bed material (SBM). Compressive strengths ranging from 84 lbs per square inch (psi) to 298 psi were obtained from various mix designs containing different sludge-to-ash ratios cured for 28 days. All the mix designs passed the TCLP. Recoveries from leaching for each metal were less than 5% for most mix designs. Results of unconfined compressive strengths, TCLP, and percent recovery calculations indicate that the mix design containing approximately a 1:1 ratio of fly ash to char-and-sludge is the best mix design for the S/S of the metal-bearing sludge.

  10. Drying grain using a hydrothermally treated liquid lignite fuel

    Energy Technology Data Exchange (ETDEWEB)

    Bukurov, Z.; Cvijanovic, P.; Bukurov, M. [Univ. of Novi Sad (Yugoslavia); Ljubicic, B.R. [Univ. of North Dakota, Grand Forks, ND (United States)

    1995-12-01

    A shortage of domestic oil and natural gas resources in Yugoslavia, particularly for agricultural and industrial purposes, has motivated the authors to explore the possibility of using liquid lignite as an alternate fuel for drying grain. This paper presents a technical and economic assessment of the possibility of retrofitting grain-drying plants currently fueled by oil or natural gas to liquid lignite fuel. All estimates are based on lignite taken from the Kovin deposit. Proposed technology includes underwater mining techniques, aqueous ash removal, hydrothermal processing, solids concentration, pipeline transport up to 120 km, and liquid lignite direct combustion. For the characterization of Kovin lignite, standard ASTM procedures were used: proximate, ultimate, ash, heating value, and Theological analyses were performed. Results from an extensive economic analysis indicate a delivered cost of US$20/ton for the liquid lignite. For the 70 of the grain-drying plants in the province of Vojvodina, this would mean a total yearly saving of about US $2,500,000. The advantages of this concept are obvious: easy to transport and store, nonflammable, nonexplosive, nontoxic, 30%-40% cheaper than imported oil and gas, domestic fuel is at hand. The authors believe that liquid lignite, rather than an alternative, is becoming more and more an imperative.

  11. Use of lignite fly ash as an additive in alkaline stabilisation and pasteurisation of wastewater sludge

    Energy Technology Data Exchange (ETDEWEB)

    Kocaer, F.O.; Alkan, U.; Baskaya, H.S. [Uludag University, Bursa (Turkey). Faculty of Engineering & Architecture

    2003-10-01

    The possibility of using lignite fly ash in low doses for reducing the pathogen levels in wastewater sludge was investigated. The results showed that using fly ash alone in doses of 40%,80% and 120% (on a dry weight basis), did not produce an alkaline environment for an efficient removal of pathogens. However, using fly ash in conjunction with the minimum amount of quicklime may act as an effective way of fecal coliform removal in both alkaline stabilisation and pasteurisation processes. It was shown that using fly ash in doses of 80% and 120% in alkaline stabilisation and pasteurisation processes prevented the pH decays and regrowth of pathogens during 60 days of storage period. The results of the study confirmed that alkaline pasteurisation process produces a product which is more resistant to pH decays and regrowth of fecal coliforms compared to that of alkaline stabilisation. Consequently, the overall results of this study indicated that the minimum lime and fly ash dosages required to generate a Class B biosolid were 10-15% and 80%, respectively. On the other hand, heating sludge to 50{degree}C prior to the addition of 10-15% quicklime and 80% fly ash followed by further heating to 70{degree}C and then sustaining at this temperature for 30 minutes were sufficient to generate a Class A biosolid.

  12. Baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota

    Energy Technology Data Exchange (ETDEWEB)

    1994-11-01

    This baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota, evaluates the potential impacts to public health or the environment from contaminated ground water at this site. This contamination is a result of the uraniferous lignite ashing process, when coal containing uranium was burned to produce uranium. Potential risk is quantified only for constituents introduced by the processing activities and not for the constituents naturally occurring in background ground water in the site vicinity. Background ground water, separate from any site-related contamination, imposes a percentage of the overall risk from ground water ingestion in the Bowman site vicinity. The US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project is developing plans to address soil and ground water contamination at the site. The UMTRA Surface Project involves the determination of the extent of soil contamination and design of an engineered disposal cell for long-term storage of contaminated materials. The UMTRA Ground Water Project evaluates ground water contamination. Based on results from future site monitoring activities as defined in the site observational work plan and results from this risk assessment, the DOE will propose an approach for managing contaminated ground water at the Bowman site.

  13. Baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota

    International Nuclear Information System (INIS)

    1994-11-01

    This baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota, evaluates the potential impacts to public health or the environment from contaminated ground water at this site. This contamination is a result of the uraniferous lignite ashing process, when coal containing uranium was burned to produce uranium. Potential risk is quantified only for constituents introduced by the processing activities and not for the constituents naturally occurring in background ground water in the site vicinity. Background ground water, separate from any site-related contamination, imposes a percentage of the overall risk from ground water ingestion in the Bowman site vicinity. The US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project is developing plans to address soil and ground water contamination at the site. The UMTRA Surface Project involves the determination of the extent of soil contamination and design of an engineered disposal cell for long-term storage of contaminated materials. The UMTRA Ground Water Project evaluates ground water contamination. Based on results from future site monitoring activities as defined in the site observational work plan and results from this risk assessment, the DOE will propose an approach for managing contaminated ground water at the Bowman site

  14. The effects of leaching and floatation on the ash fusion temperatures of three selected lignites

    Energy Technology Data Exchange (ETDEWEB)

    Feng-hai Li; Jie-jie Huang; Yi-tian Fang; Yang Wang [Chinese Academy of Sciences, Taiyuan (China). Institute of Coal Chemistry

    2011-07-15

    Experiments have been conducted with Huolinhe (HLH), Xiaolongtan (XLT), and Ethiopian (ET) lignites to investigate the effects of washing with water, acid-leaching, and floatation on their ash fusion temperatures (AFTs). The results show that the AFTs of XLT and ET are elevated by washing with water and floatation, but the AFT of HLH is decreased. The AFTs of all three lignites are increased markedly by acid leaching. A decrease in the total basic composition in ash increases its AFT, and vice versa. Changes in the mineral contents of the coals after treatment contribute to the variations in their AFTs. After washing with water, the lower AFT of HLH is brought about by the increases in the amounts of cordierite and anhydrite, whereas the higher AFT of XLT is caused by the decreases in the amounts of anhydrite and calcite. For the floatation treatment, the decrease of AFT for HLH is due to the reduction in the amount of kaolinite, but the elevation of AFT for XLT or ET is caused by the decrease in the amount of pyrite and the reductions in the amounts of gypsum and xanthoxenite, respectively. For the acid-leaching treatment, a decrease in the amount of pyrite and an increase in the amount of kaolinite result in increases in AFTs for HLH and XLT. Increases in the amounts of kaolinite and cristobalite in FET (ET after floatation), WET (ET after washing with water), and AET (ET after acid-leaching) lead to corresponding increases in the AFTs. 27 refs., 10 figs., 3 tabs.

  15. Reuse of Partially Sulphated CFBC Ash as an SO2 Sorbent

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Yinghai; Jia, Lufei; Anthony, E.J. [CanmetENERGY, 1 Haanel Drive, Ottawa, Ontario, K1A1M1 (Canada); Nobili, M.; Telesca, A. [Department of Environmental Engineering and Physics, University of Basilicata, Viale dell' Ateneo, Lucano 10, 85100 Potenza (Italy); Montagnaro, F. [Department of Chemistry, University of Naples ' Federico II' , Monte Sant' Angelo, 80126 Naples (Italy)

    2010-06-15

    Ashes produced from fluidized bed combustors (FBC) burning high-sulphur fuels often contain 20-30 % unreacted CaO because of the limestone added to remove SO2 in situ. This paper presents the results from experiments into reactivating partially sulphated FBC ash (both bed ash and fly ash) with liquid water, steam and sodium carbonate. The water- or steam-hydrated ashes were subsequently re-sulphated in a thermogravimetric analyzer (TGA) with simulated flue gas. The TGA results show that, while liquid water and steam successfully hydrate and reactivate the unreacted CaO in the bed ash, the treated ashes sulphated to widely different extents. Attempts to reactivate fly ash with hydration failed, although fly ash by itself is extremely reactive. A pilot-scale mini-circulating FBC (CFBC) was also used to evaluate the results of reactivation on the bed ash by hydrating with liquid water and admixtures of inorganic salt (Na2CO3) in the form of either powder or solution. When the treated ash was re-injected into the combustor with the fuel, the effect on SO2 removal efficiency was negligible if Na2CO3 was added as powder. Doping with aqueous solution resulted in enhanced SO2 removal; however, the extent was lower than the level achieved if only water hydration was employed. Increasing the amount of water (from 10% to 30%) to reactivate the ash did not improve the sulphur capture capacity in the mini-CFBC. Overall, this study suggests that the most practical way for re-use of the partially sulphated bed ash as a sulphur sorbent is reactivation by water. A proposal for utilization of the fly ash in an economically reasonable way is also discussed.

  16. Organic petrographical, mineralogical and geochemical features of the Achlada and Mavropigi lignite deposits, NW Macedonia, Greece

    Energy Technology Data Exchange (ETDEWEB)

    Koukouzas, Nikolaos [Centre for Research and Technology Hellas, Institute for Solid Fuels Technology and Applications, Mesogeion Ave. 357-359, GR-15231 Halandri, Athens (Greece); Kalaitzidis, Stavros P. [Geological Services, BHP Billiton Mitsubishi Alliance, Central Queensland Office, Peak Downs Mine, Moranbah, QLD 4744 (Australia); Ward, Colin R. [School of Biological, Earth and Environmental Sciences, University of New South Wales, Sydney, NSW 2052 (Australia)

    2010-09-01

    The Achlada and Mavropigi lignite deposits in northern Greece provide the main coal source for the next generation of Greek power plants. A comparative characterization of these two lignite deposits is presented, covering the coal rank and the features of the maceral components, based on detailed coal petrography, and the mineralogical and geochemical features of the coals and their ashes, based on XRF and XRD analyses. The data are used to interpret the palaeoenvironments of the lignite beds, as well as factors that may affect their burnout behavior. Both deposits have a lignite C rank. The Mavropigi lignite is mainly a matrix lignite lithotype, whereas the Achlada deposit consists both of matrix and xylite-rich lithotypes. The Achlada lignite was formed in a fluviatile environment, mainly in the abandoned channels of a meandering river system during flooding periods; hence it is enriched in inorganic matter, with ash values > 30 wt.%. The Mavropigi lignite formed in a reed-marsh environment under limno-telmatic conditions, and displays ash values < 30 wt.%. The inorganic matter of the two deposits is different in composition due to the contrasting environments, and these differences should be taken into account in optimizing their utilization for power production. A preliminary assessment indicates that the Achlada lignite may have more favorable slagging and fouling properties than the Mavropigi lignite, although experimental studies are required for more solid conclusions to be reached. (author)

  17. Characterization of ashes from a 100 kWth pilot-scale circulating fluidized bed with oxy-fuel combustion

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Y.H.; Wang, C.B.; Tan, Y.W.; Jia, L.F.; Anthony, E.J. [Natural Resources Canada, Ottawa, ON (Canada)

    2011-09-15

    Oxy-fuel combustion experiments have been carried out on an oxygen-fired 100 kW(th) mini-circulating fluidized bed combustion (CFBC) facility. Coal and petroleum coke were used as fuel together with different limestones (and fixed Ca:S molar ratios) premixed with the fuel, for in situ SO{sub 2} capture. The bed ash (BA) and fly ash (FA) samples produced from this unit were collected and characterized to obtain physical and chemical properties of the ash samples. The characterization methods used included X-ray fluorescence (XRF), X-ray diffraction (XRD), char carbon and free lime analysis, thermogravimetric analysis (TGA), and surface analysis. The main purpose of this work is to characterize the CFBC ashes from oxy-fuel firing to obtain a better understanding of the combustion process, and to identify any significant differences from the ash generated by a conventional air-fired CFBC. The primary difference in the sulfur capture mechanism between atmospheric air-fired and oxy-fuel FBC, at typical FBC temperatures (similar to 850{sup o}C), is that, in the air-fired case the limestone sorbents calcine, whereas the partial pressure of CO{sub 2} in oxy-fuel FBC is high enough to prevent calcination, and hence the sulfation process should mimic that seen in pressurized FBC (PFBC). Here, the char carbon content in the fly ash was much higher than that in the bed ash, and was also high by comparison with ash obtained from conventional commercial air-firing CFBC units. In addition, measurements of the free lime content in the bed and fly ash showed that the unreacted Ca sorbent was present primarily as CaCO{sub 3}, indicating that sulfur capture in the oxy-fuel combustor occurred via direct sulfation.

  18. Natural radioactivity releases from lignite power plants in Southwestern Anatolia

    International Nuclear Information System (INIS)

    Yaprak, G.; Guer, F.; Cam, F.; Candan, O.

    2006-01-01

    The Mugla basin is one of the most productive lignite basins in Southwestern Anatolia, Turkey. Mining activities started in 1979 and total reserves were estimated during exploration at 767.5 million tonnes. Total mean annual lignite production of the Mugla basin is estimated at about 10 million tonnes per year. Most of the lignite production supplies three thermal power plants (Yatagan 630 MW, Yenikoey 420 MW, Kemerkoey 630 MW) with a total capacity of 1680 MW. It is well known that the lignite contains naturally occurring primordial radionuclides arising from the uranium and thorium series as well as from 4 0K. Lignite burning is, therefore, one of the sources of technologically enhanced exposure to humans from natural radionuclides. The investigation reported here deals with the determination of the 2 26Ra, 2 32Th and 4 0K concentrations in the lignite feeding 3 thermal power plants in Mugla region and in the product ash. Samples of lignite feeding the power plants and fly and bottom ashes produced in the same power plants were collected over a period of 1 year and therefore systematic sampling allowed for the determination of mean representative values for the natural radioactivity content of above materials and also estimation of the radioactivity releases to the environment. Furthermore, grid soil sampling within 10-15 km around the power plants allowed for the mapping of the surface soil activity of natural radionuclides. Dosimetric calculations from terrestrial gamma radiation for the population living around the power plants were performed based on the guidance of UNSCEAR 2000 report

  19. Steam hydration-reactivation of FBC ashes for enhanced in situ desulphurization

    Energy Technology Data Exchange (ETDEWEB)

    Fabio Montagnaro; Marianna Nobili; Antonio Telesca; Gian Lorenz Valenti; Edward J. Anthony; Piero Salatino [Universita degli Studi di Napoli Federico II, Napoli (Italy). Dipartimento di Chimica

    2009-06-15

    Bed and fly ashes originating from industrial-scale fluidized bed combustors (FBCs) were steam hydrated to produce sorbents suitable for further in situ desulphurization. Samples of the hydrated ash were characterized by X-ray diffraction analysis, scanning electron microscopy and porosimetry. Bed ashes were hydrated in a pressure bomb for 30 and 60 min at 200{sup o}C and 250{sup o}C. Fly ash was hydrated in an electrically heated tubular reactor for 10 and 60 min at 200{sup o}C and 300{sup o}C. The results were interpreted by considering the hydration process and the related development of accessible porosity suitable for resulphation. The performance of the reactivated bed ash as sulphur sorbent improved with a decrease of both the hydration temperature and time. For reactivated fly ash, more favourable porosimetric features were observed at longer treatment times and lower hydration temperatures. Finally, it was shown that an ashing treatment (at 850{sup o}C for 20 min) promoted a speeding up of the hydration process and an increase in the accessible porosity. 36 refs., 6 figs., 2 tabs.

  20. Analytical investigation of lignite and its ash samples taken from the Afsin-Elbistan coal basin in Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Kucukonder, Adnan; Paksoy, Emine; Biber, Seyma [Kahramanmaras Suetcue Imam Univ. (Turkey). Dept. of Physics; Durdu, Burhanettin Goeker [Kilis 7 Aralik Univ., Kilis (Turkey). Opticianry Program; Baskaya, H.; Dogru, Mahmut [Bitlis Eren Univ. (Turkey). Dept. of Physics

    2014-04-15

    Lignite, taken from basin in Afsin-Elbistan region, and ash samples were analyzed according to the qualitative, quantitative and radioactivity properties. An elemental analysis was made by using the Energy Dispersive X-Ray Fluorescence (EDXRF) technique. 59.5 keV photons emitted from a {sup 241}Am source and 5.9 keV photons emitted from a {sup 55}Fe radioactive source were used for excitation. The characteristic K X-rays of the elements were counted with a Si(Li) detector. For the same samples gross alpha, gross beta and radionuclide activities were also measured. (orig.)

  1. Catalytic cracking of lignites

    Energy Technology Data Exchange (ETDEWEB)

    Seitz, M.; Nowak, S.; Naegler, T.; Zimmermann, J. [Hochschule Merseburg (Germany); Welscher, J.; Schwieger, W. [Erlangen-Nuernberg Univ. (Germany); Hahn, T. [Halle-Wittenberg Univ., Halle (Germany)

    2013-11-01

    A most important factor for the chemical industry is the availability of cheap raw materials. As the oil price of crude oil is rising alternative feedstocks like coal are coming into focus. This work, the catalytic cracking of lignite is part of the alliance ibi (innovative Braunkohlenintegration) to use lignite as a raw material to produce chemicals. With this new one step process without an input of external hydrogen, mostly propylene, butenes and aromatics and char are formed. The product yield depends on manifold process parameters. The use of acid catalysts (zeolites like MFI) shows the highest amount of the desired products. Hydrogen rich lignites with a molar H/C ratio of > 1 are to be favoured. Due to primary cracking and secondary reactions the ratio between catalyst and lignite, temperature and residence time are the most important parameter to control the product distribution. Experiments at 500 C in a discontinuous rotary kiln reactor show yields up to 32 wt-% of hydrocarbons per lignite (maf - moisture and ash free) and 43 wt-% char, which can be gasified. Particularly, the yields of propylene and butenes as main products can be enhanced four times to about 8 wt-% by the use of catalysts while the tar yield decreases. In order to develop this innovative process catalyst systems fixed on beads were developed for an easy separation and regeneration of the used catalyst from the formed char. (orig.)

  2. Combustion of uraniferous lignites in fluidized bed

    International Nuclear Information System (INIS)

    Morales, G.; Gasos, P.

    1985-01-01

    In this paper a description of the continuous fluid bed combustion pilot plant unit, installed in the Junta de Energia Nuclear facilities, is presented. Besides, this paper deals with some of the studies carried out in the pilot plant aimed at the recovery of uranium from lignites, high in sulfur and ashes, coming from Calaf basin (Barcelona). These studies include the recovery of the heating value of these lignites and the reduction of environmental effect of SO 2 . Based on these studies an application exercise is presented. 9 references, 5 figures, 5 tables

  3. Eocene Yegua Formation (Claiborne group) and Jackson group lignite deposits of Texas

    Science.gov (United States)

    Hook, Robert W.; Warwick, Peter D.; Swanson, Sharon M.; Hackley, Paul C.; Warwick, Peter D.; Karlsen, Alexander K.; Merrill, Matthew D.; Valentine, Brett J.

    2011-01-01

    The lignite deposits within the upper Eocene Yegua Formation (Claiborne Group) and the overlying Jackson Group are among the coal resources that were not quantitatively assessed as part of the U.S. Geological Survey's (USGS) National Coal Resource Assessment (NCRA) program in the Gulf Coastal Plain coal province. In the past, these lignite-bearing stratigraphic units often have been evaluated together because of their geographic and stratigraphic proximity (Fisher, 1963; Kaiser, 1974; Kaiser et al., 1980; Jackson and Garner, 1982; Kaiser, 1996) (Figures 1, 2). The term “Yegua-Jackson trend“ is used informally herein for the lignite-bearing outcrops of these Late Eocene deposits in Texas. Lignite beds in the Yegua-Jackson trend generally are higher both in ash yield and sulfur content than those of the underlying Wilcox Group (Figure 2). Recent studies (Senkayi et al., 1987; Ruppert et al., 1994; Warwick et al., 1996, 1997) have shown that some lignite beds within the Yegua-Jackson trend contain partings of volcanic ash and host elevated levels of trace elements that have been identified as potentially hazardous air pollutants (HAPs) in the United States Clean Air Amendments of 1990. Lignite beds within the Yegua Formation are thin (less than or equal to 6 ft) and laterally discontinuous in comparison with most Wilcox Group deposits (Ayers, 1989a); in contrast, the Jackson Group lignite beds range up to 12 ft in total thickness and are relatively continuous laterally, extending nearly 32 mi along strike.

  4. Effect of mineral oxides on slag formation tendency of Mae Moh lignites

    Directory of Open Access Journals (Sweden)

    Anuwat Luxsanayotin

    2010-08-01

    Full Text Available Slagging is one of major ash deposition problems experienced in the boilers of coal–fired power plants especially theplants that use lignite, like Mae Moh lignites. The occurrence of slag is a complex phenomenon depending on several factorssuch as ash properties, furnace operating conditions, and coal properties. The main objective of this work is to study theeffect of mineral components in Mae Moh lignite on ash fusion temperatures (AFTs, which is commonly used as a keyindicator for slag formation tendency under pulverized combustion conditions. Two Mae Moh lignites from the coal seamsplanned to be used in the future were selected for the study to represent low CaO and high CaO lignite. The two lignites,namely K1 and K3, have 3.6 and 40.4 wt% CaO in ash, respectively. The AFT characterization shows that their initial deformationtemperatures (ITs were almost identical and considered as low for the typical flue gas temperature in the radiationsection of Mae Moh boilers, i.e. 1050-1100°C. These observed similar ITs were rather unexpected, especially for K1 consideringits sufficiently low base to acid (B/A ratios. The X-ray diffraction analyses evidently show the presence of illite, pyriteand anhydrite in K1, which explains the observed lower IT of the sample. Anhydrite, which is known to lower the ITs, is alsothe most abundant mineral in K3. Washing the lignite samples with HCl can significantly reduce CaO, MgO, and SO3 contentin the ash but not Fe2O3 as it is present in the form of pyrite. The addition of Al2O3, SiO2 and Fe2O3 can help increase AFTs ofthe studied samples. The Al2O3 addition gives the strongest effect on increasing AFTs, especially for the sample with lowAl2O3 content. When the CaO is added to the low CaO samples, the fluxing effect will initially occur. However, when the CaOcontent is higher than a critical value (i.e. CaO > 38%, the effect of its high melting point will dominate hence the AFTsincreased. Ternary phase diagrams

  5. The effect of lignite quality variation on the efficiency of on-line ash analyzers

    Energy Technology Data Exchange (ETDEWEB)

    Galetakis, Michael J. [Technical University of Crete, Dept. of Mineral Resources Engineering, University Campus, 73 100 Hania (Greece); Pavloudakis, Francis F. [Public Power Corporation SA, General Division of Mines, Kifisou and Dyrrahiou 89, 104 43 Athens (Greece)

    2009-12-01

    A sustainable coal industry needs to achieve a number of objectives including improvements in utilization of deposits, energy efficiency, and environmental performance during combustion. The ''Clean Coal Concept'' promises to combine the secure and low cost electricity supply offered by hard coal and lignite with adequate environmental precautions. In this context, modern quality control systems, which are greatly based on the on-line analyzers, play an important role in achieving sustainability targets. This paper examines the possibility of using commercial on-line analysis systems for monitoring the mineral matter content of low quality lignite mined from the lignite basin of Megalopolis, Peloponnese, Greece. The effect of the accuracy of the on-line analyzers to process control, when used for the characterization of low rank coals with complex and variable composition, is investigated by carrying out numerous bench- and pilot-scale trials. Pilot-scale trials were based on a dual energy gamma-ray transmission analyzer, which was installed on the conveyor belt that transports lignite from the mine pit to the homogenization stockyard. All measurement data were compared to data gathered during the realisation of similar trials in the lignite mines of Ptolemais Basin, Northern Greece. Results indicated that the accuracy of the on-line measurements was not satisfactory and did not allow lignite quality monitoring in real time. The achieved inferior accuracy of the on-line measurement's accuracy, compared to previous applications at other mining sites, was related to the intense variation of the mineral matter content of lignite and lignite composition, which distorted the calibration of the analyzer. The latter is based on certain assumptions regarding the average mass absorption coefficient of the organic and mineral matter contained in the lignite. Further experimental work is needed to investigate solutions for successful implementation of

  6. Management of Lignite Fly Ash for Improving Soil Fertility and Crop Productivity

    Science.gov (United States)

    Ram, Lal C.; Srivastava, Nishant K.; Jha, Sangeet K.; Sinha, Awadhesh K.; Masto, Reginald E.; Selvi, Vetrivel A.

    2007-09-01

    Lignite fly ash (LFA), being alkaline and endowed with excellent pozzolanic properties, a silt loam texture, and plant nutrients, has the potential to improve soil quality and productivity. Long-term field trials with groundnut, maize, and sun hemp were carried out to study the effect of LFA on growth and yield. Before crop I was sown, LFA was applied at various doses with and without press mud (an organic waste from the sugar industry, used as an amendment and source of nutrients). LFA with and without press mud was also applied before crops III and V were cultivated. Chemical fertilizer, along with gypsum, humic acid, and biofertilizer, was applied in all treatments, including the control. With one-time and repeat applications of LFA (with and without press mud), yield increased significantly (7.0-89.0%) in relation to the control crop. The press mud enhanced the yield (3.0-15.0%) with different LFA applications. The highest yield LFA dose was 200 t/ha for one-time and repeat applications, the maximum yield being with crop III (combination treatment). One-time and repeat application of LFA (alone and in combination with press mud) improved soil quality and the nutrient content of the produce. The highest dose of LFA (200 t/ha) with and without press mud showed the best residual effects (eco-friendly increases in the yield of succeeding crops). Some increase in trace- and heavy-metal contents and in the level of γ-emitters in soil and crop produce, but well within permissible limits, was observed. Thus, LFA can be used on a large scale to boost soil fertility and productivity with no adverse effects on the soil or crops, which may solve the problem of bulk disposal of fly ash in an eco-friendly manner.

  7. Natural desulfurization in coal-fired units using Greek lignite.

    Science.gov (United States)

    Konidaris, Dimitrios N

    2010-10-01

    This paper analyzes the natural desulfurization process taking place in coal-fired units using Greek lignite. The dry scrubbing capability of Greek lignite appears to be extremely high under special conditions, which can make it possible for the units to operate within the legislative limits of sulfur dioxide (SO2) emissions. According to this study on several lignite-fired power stations in northern Greece, it was found that sulfur oxide emissions depend on coal rank, sulfur content, and calorific value. On the other hand, SO2 emission is inversely proportional to the parameter gammaCO2(max), which is equal to the maximum carbon dioxide (CO2) content by volume of dry flue gas under stoichiometric combustion. The desulfurization efficiency is positively correlated to the molar ratio of decomposed calcium carbonate to sulfur and negatively correlated to the free calcium oxide content of fly ash.

  8. Investigation of pre-drying lignite in an existing Greek power plant

    Directory of Open Access Journals (Sweden)

    Agraniotis Michalis

    2012-01-01

    Full Text Available The application of lignite pre-drying technologies in next generation of lignite power plants by utilizing low pressure steam as a drying medium instead of hot recirculated flue gas - combined with thermal utilization of the vaporized coal moisture - is expected to bring efficiency increase of 2-4 percentage points in future lignite power plants compared with today’s state of the art. The pre-drying concept is of particular importance in Greek boilers firing lignite with a high water and ash content. The combustion of Greek predried lignite has been investigated experimentally and via numerical simulations in our previous research. This study focuses on the potential integration of a lignite pre-drying system in an existing Greek power plant with dry lignite co-firing thermal share of up to 30%. The radiative and convective heat fluxes to the boiler and the overall boiler heat balance is calculated for reference and dry lignite co-firing conditions by an in-house calculation code. The overall plant’s thermal cycle is then simulated using commercial thermal cycle calculation software. The net plant efficiency is in this way determined for reference and dry coal co-firing conditions. According to the simulation results the integration of a pre-drying system and the implementation of dry lignite co-firing may bring an efficiency increase of about 1.5 percentage points in existing Greek boilers. It is therefore considered as an important measure towards improving plant efficiency and reducing specific CO2 emissions in existing plants.

  9. Mineralogical investigations into ash deposits of selected brown coals; Mineralogische Untersuchungen an Ascheansaetzen ausgewaehlter Braunkohlen

    Energy Technology Data Exchange (ETDEWEB)

    Szilagyi, J.; Ullrich, B. [Technische Univ. Dresden, Inst. fuer Geotechnik (Germany)

    2003-07-01

    Within the framework of the research project financed by the Arbeitsgemeinschaft industrieller Forschungsvereinigungen (AIF) ''Experimental investigations into the formation of ash deposits from stack gases during the combustion of pulverised lignite'' and supervised by the chair of power station technology (Institute of Energy Technology) of the Dresden Technical University, the mineral composition of ash deposits of six different coals were investigated: two coal blends (different countries worldwide), two lignites from east from the River Elbe (types WM and JAe), one from west of the River Elbe and one Rhenish lignite. (orig.)

  10. Properties and potential of formed cokes derived from two Turkish lignites by carbonization of binderless briquettes

    Energy Technology Data Exchange (ETDEWEB)

    Bayraktur, K.N.; Lawson, G.J.

    1984-09-01

    Two high-sulphur Turkish lignites were briquetted at room temperature under pressures of 113 or 212 MPa and the briquettes were carbonized to 1158-1173 K over special heating cycles. The lowerrank lignite gave a formed coke of superior mechanical strength, lower porosity and higher sulphur content than typical blast furnace cokes. The formed coke produced from the higher-rank lignite briquettes had slightly poorer mechanical strength, lower porosity and much higher ash and sulphur content than conventional cokes. The products were considered attractive for use in non-ferrous metallurgy.

  11. Properties and potential of formed cokes derived from two Turkish lignites by carbonization of binderless briquettes

    Energy Technology Data Exchange (ETDEWEB)

    Bayraktar, K.N.; Lawson, G.J.

    1984-09-01

    Two high-sulphur Turkish lignites were briquetted at room temperature under pressures of 113 or 212 MPa and the briquettes were carbonized to 1158-1173 K over special heating cycles. The lower-rank lignite gave a formed coke of superior mechanical strength, lower porosity and higher sulphur content than typical blast furnace cokes. The formed coke produced from the higher-rank lignite briquettes had slightly poorer mechanical strength, lower porosity and much higher ash yield and sulphur content than conventional cokes. The products were considered attractive for use in non-ferrous metallurgy. 38 references.

  12. Naturally Occurring Radionuclides of Ash Produced by Coal Combustion. The Case of the Kardia Mine in Northern Greece

    Science.gov (United States)

    Fotakis, M.; Tsikritzis, L.; Tzimkas, N.; Kolovos, N.; Tsikritzi, R.

    2008-08-01

    West Macedonia Lignite Center (WMLC), located in Northwest Greece, releases into the atmosphere about 21,400 tons/year of fly ash through the stacks of four coal fired plants. The lignite ash contains naturally occurring radionuclides, which are deposited on the WMLC basin. This work investigates the natural radioactivity of twenty six ash samples, laboratory produced from combustion of lignite, which was sampled perpendicularly to the benches of the Kardia mine. The concentrations of radionuclides 40K, 235U, 238U, 226Ra, 228Ra and 232Th, were measured spectroscopically and found round one order of magnitude as high as those of lignite. Subsequently the Radionuclide Partitioning Coefficients of radionuclides were calculated and it was found that they are higher for 232Th, 228Ra and 40K, because the latter have closer affinity with the inorganic matrix of lignite. During combustion up to one third of the naturally occurring radioisotopes escape from the solid phase into the flue gases. With comparison to relative global data, the investigated ash has been found to have relatively high radioactivity, but the emissions of the WMLC radionuclides contribute only 0.03% to the mean annual absorbed dose.

  13. Naturally Occurring Radionuclides of Ash Produced by Coal Combustion. The Case of the Kardia Mine in Northern Greece

    International Nuclear Information System (INIS)

    Fotakis, M.; Tsikritzis, L.; Tzimkas, N.; Kolovos, N.; Tsikritzi, R.

    2008-01-01

    West Macedonia Lignite Center (WMLC), located in Northwest Greece, releases into the atmosphere about 21,400 tons/year of fly ash through the stacks of four coal fired plants. The lignite ash contains naturally occurring radionuclides, which are deposited on the WMLC basin. This work investigates the natural radioactivity of twenty six ash samples, laboratory produced from combustion of lignite, which was sampled perpendicularly to the benches of the Kardia mine. The concentrations of radionuclides 40 K, 235 U, 238 U, 226 Ra, 228 Ra and 232 Th, were measured spectroscopically and found round one order of magnitude as high as those of lignite. Subsequently the Radionuclide Partitioning Coefficients of radionuclides were calculated and it was found that they are higher for 232 Th, 228 Ra and 40 K, because the latter have closer affinity with the inorganic matrix of lignite. During combustion up to one third of the naturally occurring radioisotopes escape from the solid phase into the flue gases. With comparison to relative global data, the investigated ash has been found to have relatively high radioactivity, but the emissions of the WMLC radionuclides contribute only 0.03% to the mean annual absorbed dose

  14. Distribution and correlation of the natural radionuclides in a coal mine of the West Macedonia Lignite Center (Greece).

    Science.gov (United States)

    Tsikritzis, L I; Fotakis, M; Tzimkas, N; Kolovos, N; Tsikritzi, R

    2008-02-01

    The distribution and correlation of six natural nuclides in the West Macedonia Lignite Center, Northern Greece were studied. Fifty-five samples of lignite, aged from 1.8 to 5 million years, and corresponding steriles, beds of marls, clays and sands alternating with the lignite, were collected perpendicular to the mine benches and measured spectroscopically. The mean concentrations of (238)U and (226)Ra in lignites were found to be higher than that in steriles since these nuclides are associated with the organic material of lignite, whereas (238)U/(226)Ra equilibrium was not observed in either lignites or steriles. Finally, the ratio (226)Ra/(228)Ra in lignites was approximately double of that in steriles, confirming the affinity of the (238)U series with the coal matrix in contrast to the (232)Th series. No correlation was found between radionuclide concentrations and the depth of the sample, nor with the ash content of lignite.

  15. Environmental assessment of no remedial action at the inactive uraniferous lignite ashing sites at Belfield and Bowman, North Dakota

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-01

    The Belfield and Bowman sites were not included on the original congressional list of processing sites to be designated by the Secretary of Energy. Instead, the sites were nominated for designation by the Dakota Resource Council in a letter to the DOE (September 7, 1979). In a letter to the DOE (September 12, 1979), the state of North Dakota said that it did not believe the sites would qualify as processing sites under the Uranium Mill Tailings Radiation Control Act (UMTRCA) because the activities at the sites involved only the ashing of uraniferous lignite coal and the ash was shipped out of state for actual processing. Nevertheless, on October 11, 1979, the state of North Dakota agreed to the designation of the sites because they met the spirit of the law (reduce public exposure to radiation resulting from past uranium operations). Therefore, these sites were designated by the Secretary of Energy for remedial action. Because of the relatively low health impacts determined for these sites, they were ranked as low priority and scheduled to be included in the final group of sites to be remediated.

  16. Environmental assessment of no remedial action at the inactive uraniferous lignite ashing sites at Belfield and Bowman, North Dakota

    International Nuclear Information System (INIS)

    1997-06-01

    The Belfield and Bowman sites were not included on the original congressional list of processing sites to be designated by the Secretary of Energy. Instead, the sites were nominated for designation by the Dakota Resource Council in a letter to the DOE (September 7, 1979). In a letter to the DOE (September 12, 1979), the state of North Dakota said that it did not believe the sites would qualify as processing sites under the Uranium Mill Tailings Radiation Control Act (UMTRCA) because the activities at the sites involved only the ashing of uraniferous lignite coal and the ash was shipped out of state for actual processing. Nevertheless, on October 11, 1979, the state of North Dakota agreed to the designation of the sites because they met the spirit of the law (reduce public exposure to radiation resulting from past uranium operations). Therefore, these sites were designated by the Secretary of Energy for remedial action. Because of the relatively low health impacts determined for these sites, they were ranked as low priority and scheduled to be included in the final group of sites to be remediated

  17. Lignite chemical conversion in an indirect heat rotary kiln gasifier

    Directory of Open Access Journals (Sweden)

    Hatzilyberis Kostas S.

    2006-01-01

    Full Text Available The results on the gasification of Greek lignite using two indirect heat (allothermal pilot rotary kiln gasifiers are reported in the present work. The development of this new reactor-gasifier concept intended for solid fuels chemical conversion exploits data and experience gained from the following two pilot plants. The first unit A (about 100 kg/h raw lignite demonstrated the production of a medium heating value gas (12-13 MJ/Nm3 with quite high DAF (dry ash free coal conversions, in an indirect heat rotary gasifier under mild temperature and pressure conditions. The second unit B is a small pilot size unit (about 10 kg/h raw lignite comprises an electrically heated rotary kiln, is an operation flexible and exhibits effective phase mixing and enhanced heat transfer characteristics. Greek lignite pyrolysis and gasification data were produced from experiments performed with pilot plant B and the results are compared with those of a theoretical model. The model assumes a scheme of three consecutive-partly parallel processes (i. e. drying, pyrolysis, and gasification and predicts DAF lignite conversion and gas composition in relatively good agreement with the pertinent experimental data typical of the rotary kiln gasifier performance. Pilot plant B is currently being employed in lime-enhanced gasification studies aiming at the production of hydrogen enriched synthesis gas. Presented herein are two typical gas compositions obtain from lignite gasification runs in the presence or not of lime. .

  18. Petrography and geochemistry of selected lignite beds in the Gibbons Creek mine (Manning Formation, Jackson Group, Paleocene) of east-central Texas

    Science.gov (United States)

    Warwick, Peter D.; Crowley, Sharon S.; Ruppert, Leslie F.; Pontolillo, James

    1997-01-01

    This study examined the petrographic and geochemical characteristics of two lignite beds (3500 and 4500 beds, Manning Formation, Jackson Group, Eocene) that are mined at the Gibbons Creek mine in east-central Texas. The purpose of the study was to identify the relations among sample ash yield, coal petrography, and trace-element concentrations in lignite and adjoining rock layers of the Gibbons Creek mine. Particular interest was given to the distribution of 12 environmentally sensitive trace elements (As, Be, Cd, Cr, Co, Hg, Mn, Ni, Pb, Sb, Se, and U) that have been identified as potentially hazardous air pollutants (HAPs) in the United States Clean Air Act Amendments of 1990. Eleven lignite, floor, and rock parting samples were collected from incremental channel samples of the 3500 and 4500 beds that were exposed in a highwall of pit A3 at the Gibbons Creek mine. Short proximate and ultimate and forms of sulfur analyses were performed on all lignite samples, and lignite and rock samples were analyzed for 60 major, minor and trace elements. Representative splits of all lignite samples were ground and cast into pellets, and polished for petrographic analyses in blue-light fluorescence and reflected white light to determine liptinite, inertinite, and huminite maceral group percentages. The following observations summarize our results and conclusions about the geochemistry, petrography, and sedimentology of the 3500 and 4500 beds of the Gibbons Creek lignite deposit: (1) Weighted average dry (db) ash yield for the two beds is 29.7%, average total sulfur content is 2.6%, and average calorific value is 7832 Btu (18.22 MJ/kg). Ash yields are greatest in the lower bench (59.33% db) of the 3500 bed and in the upper bench of the 4500 bed (74.61% db). (2) For lignite samples (on a whole-coal basis), the distributions of two of the HAPs (Pb and Sb) are positively related to ash yield, probably indicating an inorganic affinity for these elements. By using cluster analysis we

  19. Valorization of lignite combustion residues and ferroalumina in the production of aggregates.

    Science.gov (United States)

    Anagnostopoulos, I M; Stivanakis, V E; Angelopoulos, G N; Papamantellos, D C

    2010-02-15

    The present research study investigates the synergy of industrial solid by-products from lignite combustion (fly ash and bottom ash) and aluminum production (ferroalumina) in the production of lightweight aggregates (LWA). The process consists of two stages, pelletization and sintering. Bottom ash (BA) is used as the principal raw material in mixtures while ferroalumina (FAL) is added in lower percentages (5-30 wt%). BA carbon content is used as the fuel of sintering process in high temperatures, around 1250 degrees C, and gas generation is responsible for porous structure formation. Physical properties such as porosity, water absorption and bulk density, of sintering products are measured. Increase of FAL percentage in sintering mixtures results in decrease of porosity from 61% to 35% and of water absorption from 61% to 21% and in increase of bulk density from 1.02 g/cm(3) to 1.80 g/cm(3) of the produced aggregates. Aggregates produced by FAL addition up to 20 wt% are characterized as LWA. Aggregates formed are used in the production of concrete specimens. Compressive strength of concrete increases by increasing FAL addition in aggregates from 5 wt% to 15 wt% (highest strength value), while decrease by increasing FAL addition from 20 wt% to 30 wt%. FAL addition in lignite ashes sintering mixtures (up to 15 wt%) is considered as an important parameter for enhancing aggregates strength.

  20. Fly ash quality and utilization

    Energy Technology Data Exchange (ETDEWEB)

    Barta, L.E.; Lachner, L.; Wenzel, G.B. [Inst. for Energy, Budapest (Hungary); Beer, M.J. [Massachusetts Inst. of Technology, Cambridge, MA (United States)

    1995-12-01

    The quality of fly ash is of considerable importance to fly ash utilizers. The fly ash puzzolanic activity is one of the most important properties that determines the role of fly ash as a binding agent in the cementing process. The puzzolanic activity, however is a function of fly ash particle size and chemical composition. These parameters are closely related to the process of fly ash formation in pulverized coal fired furnaces. In turn, it is essential to understand the transformation of mineral matter during coal combustion. Due to the particle-to-particle variation of coal properties and the random coalescence of mineral particles, the properties of fly ash particles e.g. size, SiO{sub 2} content, viscosity can change considerably from particle to particle. These variations can be described by the use of the probability theory. Since the mean values of these randomly changing parameters are not sufficient to describe the behavior of individual fly ash particles during the formation of concrete, therefore it is necessary to investigate the distribution of these variables. Examples of these variations were examined by the Computer Controlled Scanning Electron Microscopy (CCSEM) for particle size and chemical composition for Texas lignite and Eagel Butte mineral matter and fly ash. The effect of combustion on the variations of these properties for both the fly ash and mineral matter were studied by using a laminar flow reactor. It is shown in our paper, that there are significant variations (about 40-50% around the mean values) of the above-listed properties for both coal samples. By comparing the particle size and chemical composition distributions of the mineral matter and fly ash, it was possible to conclude that for the Texas lignite mineral matter, the combustion did not effect significantly the distribution of these properties, however, for the Eagel Butte coal the combustion had a major impact on these mineral matter parameters.

  1. Acid leaching of coal: to produce clean fuels from Turkish lignite

    Energy Technology Data Exchange (ETDEWEB)

    Seferinoglu, Meryem [Mineral Research and Exploration Directorate (Turkey)], email: meryem_seferinoglu66@yahoo.com; Duzenli, Derya [Ankara Central Laboratory (Turkey)

    2011-07-01

    With the increasing concerns about the environment, energy producers and governments are looking at developing clean energy sources. However, Turkey has limited clean energy resources and is using low grade coal which has high sulphur content as an alternative energy source. The aim of this paper is to study the possibility of generating clean fuel from Edirne Lignite and to get a better understanding of chemical mechanisms involved in coal leaching with hydrofluoric acid (HF) solutions. Leaching was conducted on Edirne Lignite with HF solution at ambient temperature and the effects of parameters such as reaction time and concentration of acid solutions on the process were evaluated. The optimum conditions were found and it was shown that ash levels can be reduced from 28.9% to 10.5% and the calorific value increased by 500kcal/kg with the HF leaching method. This study demonstrated that the production of clean fuel from high sulphur lignite is possible.

  2. Reclamation of a uraniferous lignite mine, North Dakota: summary paper

    International Nuclear Information System (INIS)

    Houghton, R.L.; Hall, R.L.; Unseth, J.D.; Wald, J.D.; Burgess, J.L.; Patrick, D.P.; Anderson, G.S.; Hill, S.R.

    1987-01-01

    Uraniferous lignite deposits were mined from 1955 to 1967 by surface mining techniques. Overburden was stripped, and the lignite was burned to concentrate the uranium in its ash. Uranium salts in the overburden gave exposure levels of as much as 500 microroentgens/hour; water in mine pits had U concentrations from 12 to 19,000 micrograms/liter. Reclamation involved replacing the spoils into the source pit, the most contaminated spoils being placed above the water table, capping the pit with clay then topsoil containing lesser concentrations of radioactive elements, and finally planting with prairie grass. Resulting concentrations of radionuclides are given. The land is expected to remain as prairie for wildlife use, but it is safe enough for domestic animals as well. 3 figures

  3. Evaluation of ash deposits during experimental investigation of co-firing of Bosnian coal with wooden biomass

    Energy Technology Data Exchange (ETDEWEB)

    Smajevic, Izet; Kazagic, Anes [JP Elektroprivreda BiH d.d., Sarajevo (Bosnia and Herzegovina); Sarajevo Univ. (Bosnia and Herzegovina). Faculty of Mechanical Engineering

    2008-07-01

    The paper is addressed to the development and use different criteria for evaluation of ash deposits collected during experimental co-firing of Bosnian coals with wooden biomass. Spruce saw dust was used for the co-firing tests with the Kakanj brown coal and with a lignite blend consisted of the Dubrave lignite and the Sikulje lignite. The coal/biomass mixtures at 93:7 %w and at 80:20 %w were tested. Experimental lab-scale facility PF entrained flow reactor is used for the co-firing tests. The reactor allows examination of fouling/slagging behaviors and emissions at various and infinitely variable process temperature which can be set at will in the range from ambient to 1560 C. Ash deposits are collected on two non-cooled ceramic probes and one water-cooled metal surface. Six different criteria are developed and used to evaluate behavior of the ash deposits on the probes: ash deposit shape, state and structure, which are analyzed visually - photographically and optically by a microscope, rate of adhesion and ash deposit strength, analyzed by physic acting to the ash deposits, and finally deposition rate, determined as a mass of the deposit divided by the collecting area and the time of collecting. Furthermore, chemical composition analysis and AFT of the ash deposits were also done to provide additional information on the deposits. (orig.)

  4. Fusibility and sintering characteristics of ash

    Energy Technology Data Exchange (ETDEWEB)

    Ots, A. A., E-mail: aots@sti.ttu.ee [Tallinn University of Technology (Estonia)

    2012-03-15

    The temperature characteristics of ash fusibility are studied for a wide range of bituminous and brown coals, lignites, and shales with ratios R{sub B/A} of their alkaline and acid components between 0.03 and 4. Acritical value of R{sub B/A} is found at which the fusion temperatures are minimal. The sintering properties of the ashes are determined by measuring the force required to fracture a cylindrical sample. It is found that the strength of the samples increases sharply at certain temperatures. The alkali metal content of the ashes has a strong effect on their sintering characteristics.

  5. JV Task - 129 Advanced Conversion Test - Bulgarian Lignite

    Energy Technology Data Exchange (ETDEWEB)

    Michael Swanson; Everett Sondreal; Daniel Laudal; Douglas Hajicek; Ann Henderson; Brandon Pavlish

    2009-03-27

    The objectives of this Energy & Environmental Research Center (EERC) project were to evaluate Bulgarian lignite performance under both fluid-bed combustion and gasification conditions and provide a recommendation as to which technology would be the most technically feasible for the particular feedstock and also identify any potential operating issues (such as bed agglomeration, etc.) that may limit the applicability of a potential coal conversion technology. Gasification tests were run at the EERC in the 100-400-kg/hr transport reactor development unit (TRDU) on a 50-tonne sample of lignite supplied by the Bulgarian Lignite Power Project. The quality of the test sample was inferior to any coal previously tested in this unit, containing 50% ash at 26.7% moisture and having a higher heating value of 5043 kJ/kg after partial drying in preparation for testing. The tentative conclusion reached on the basis of tests in the TRDU is that oxygen-blown gasification of this high-ash Bulgarian lignite sample using the Kellogg, Brown, and Root (KBR) transport gasifier technology would not provide a syngas suitable for directly firing a gas turbine. After correcting for test conditions specific to the pilot-scale TRDU, including an unavoidably high heat loss and nitrogen dilution by transport air, the best-case heating value for oxygen-blown operation was estimated to be 3316 kJ/m{sup 3} for a commercial KRB transport gasifier. This heating value is about 80% of the minimum required for firing a gas turbine. Removing 50% of the carbon dioxide from the syngas would increase the heating value to 4583 kJ/m{sup 3}, i.e., to about 110% of the minimum requirement, and 95% removal would provide a heating value of 7080 kJ/m{sup 3}. Supplemental firing of natural gas would also allow the integrated gasification combined cycle (IGCC) technology to be utilized without having to remove CO{sub 2}. If removal of all nitrogen from the input gas streams such as the coal transport air were

  6. The content of chromium and copper in plants and soil fertilized with sewage sludge with addition of various amounts of CaO and lignite ash

    Directory of Open Access Journals (Sweden)

    Wysokiński Andrzej

    2016-09-01

    Full Text Available The influence of fertilization with fresh sewage sludge with the addition of calcium oxide and lignite ash in the proportions dry mass 6:1, 4:1, 3:1 and 2:1 on the content of chromium and copper in plants and soil and uptake of these elements was investigated in pot experiment. Sewage sludge were taken from Siedlce (sludge after methane fermentation and Łuków (sludge stabilized in oxygenic conditions, eastern Poland. The chromium content in the biomass of the test plants (maize, sunflower and oat was higher following the application of mixtures of sewage sludge with ash than of the mixtures with CaO. The copper content in plants most often did not significantly depend on the type of additives to the sludge. Various amounts of additives to the sewage sludge did not have a significant effect on the contents of either of the studied trace elements in plants. The contents of chromium and copper in soil after 3 years of cultivation of plants were higher than before the experiment, but these amounts were not significantly differentiated depending on the type and the amount of the used additive (i.e. CaO vs. ash to sewage sludge.

  7. COFIRING BIOMASS WITH LIGNITE COAL

    Energy Technology Data Exchange (ETDEWEB)

    Darren D. Schmidt

    2002-01-01

    The University of North Dakota Energy & Environmental Research Center, in support of the U.S. Department of Energy's (DOE) biomass cofiring program, completed a Phase 1 feasibility study investigating aspects of cofiring lignite coal with biomass relative to utility-scale systems, specifically focusing on a small stoker system located at the North Dakota State Penitentiary (NDSP) in Bismarck, North Dakota. A complete biomass resource assessment was completed, the stoker was redesigned to accept biomass, fuel characterization and fireside modeling tests were performed, and an engineering economic analysis was completed. In general, municipal wood residue was found to be the most viable fuel choice, and the modeling showed that fireside problems would be minimal. Experimental ash deposits from firing 50% biomass were found to be weaker and more friable compared to baseline lignite coal. Experimental sulfur and NO{sub x} emissions were reduced by up to 46%. The direct costs savings to NDSP, from cogeneration and fuel saving, results in a 15- to 20-year payback on a $1,680,000 investment, while the total benefits to the greater community would include reduced landfill burden, alleviation of fees for disposal by local businesses, and additional jobs created both for the stoker system as well as from the savings spread throughout the community.

  8. Stoichiometric calculations of combustion of Lakhra lignite

    International Nuclear Information System (INIS)

    Ali, I.; Ali, M.M.

    2002-01-01

    Lakhra coal field is largest productive coal field of Pakistan. About 1.5 millions tonne of this coal is, annually, mined and transported daily to various parts of the country in 500 trucks each of 10 tonnes of coal. The major consumers of this coal are brick kilns located in Sindh and Punjab. It is available at Rs. 500/- per tonne at mine head. A number of attempts were made for the production of power (electricity) by foreign companies. Feasibility studies were undertaken but no one set up power plant. It may be due to inferior quality of coal as it is lignitic in nature with high ash and sulfur contents. This coal is also, very sensitive to spontaneous combustion. Spontaneous combustion is the auto-ignition of coal at ambient conditions. Hence there are storage problems. In spite of these drawbacks, a 3(50) Mega Watt (3 units of each 50 mega watt power generation capacity) power plant, based on atmospheric fluidized bed combustion of coal technology (AFBC), was setup in early nineties. The performance of this plant remained poor. The main reasons might be poor quality of coal and limestone. Limestone is used with high sulfur Lakhra lignite, in fluidized bed combustor, to arrest sulfur of the coal, fixing sulfur as calcium sulfate to minimize hazardous emissions of sulfur dioxide (SO/sub 2/). Spontaneous combustion of Lakhra lignite is responsible for each fire of coal and conveyor belt etc. (author)

  9. Neutralisation potential of fly ash. Sanitation of the Burghammer lake; Neutralisationspotential von Flugaschen. Restseesanierung Burghammer

    Energy Technology Data Exchange (ETDEWEB)

    Schipek, M.; Merkel, B.; Wolkersdorfer, C. [Technische Univ. Bergakademie Freiberg (Germany). Lehrstuhl fuer Hydrogeologie; Graupner, B.; Werner, F. [Dresdner Grundwasserforschungszentrum e.V., Dresden (Germany)

    2006-07-01

    The aim of this project is to reduce the emission of carbon dioxide into the atmosphere by underwater storage, accompanied by improving the water quality in areas seriously affected by lignite mining. Carbon dioxide (CO{sub 2}) is precipitated sustainably as calcite (CaCO{sub 3}) in the sediments of the open cast lignite lakes. The project CDEAL (Carbon dioxide elimination by using acid mine lakes and calcium oxide suspensions) is designed to show that by-products (CaO from fly ashes) as well as greenhouse gases (CO{sub 2}) can be used to improve the water quality of open cast lakes and thus contributing to an environmental protection of areas affected by lignite mining operations. The lake Burghammer (Lusatia) is an ideal investigation case as it received fly ashes from the power plant ''Schwarze Pumpe'' from 1973 to 1997. The current state of the investigations is presented and shows to what degree this method can be used to remediate open cast lignite lakes. (orig.)

  10. Lignite microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Bulankina, M.A.; Lysak, L.V.; Zvyagintsev, D.G. [Moscow MV Lomonosov State University, Moscow (Russian Federation). Faculty of Soil Science

    2007-03-15

    The first demonstration that samples of lignite at a depth of 10 m are considerably enriched in bacteria is reported. According to direct microscopy, the abundance of bacteria was about 10{sup 7} cells/g. About 70% of cells had intact cell membranes and small size, which points to their anabiotic state. The fungal mycelium length was no more than 1 m. Lignite inoculation onto solid glucose-yeast-peptone medium allowed us to isolate bacteria of the genera Bacillus, Rhodococcus, Arthrobacter, Micrococcus, Spirillum, and Cytophaga. Representatives of the genera Penicillium and Trichoderma were identified on Czapek medium. Moistening of lignite powder increased the microbial respiration rate and microbial and fungal abundance but did not increase their generic diversity. This finding suggests that the studied microorganisms are autochthonous to lignite.

  11. Ash partitioning during the oxy-fuel combustion of lignite and its dependence on the recirculation of flue gas impurities (H{sub 2}O, HCl and SO{sub 2})

    Energy Technology Data Exchange (ETDEWEB)

    Facun Jiao; Juan Chen; Lian Zhang; Yajuan Wei; Yoshihiko Ninomiya; Sankar Bhattacharya; Hong Yao [Monash University, Clayton, Vic. (Australia). Department of Chemical Engineering

    2011-06-15

    Oxy-fuel combustion of a brown coal (i.e. lignite) has been carried out at 1000{sup o}C to experimentally examine the vaporisation of organically bound metals and the agglomeration of ash particles as a function of the concentration of gaseous impurities including H{sub 2}O, HCl and SO{sub 2} in about 27% O{sub 2} balanced with CO{sub 2}. The properties of bulk ash and individual metals were investigated intensively. Particularly, attention was paid to Na which is notorious for fouling and to organically bound Al which has been less studied. The results indicate that, the organically bound metals, although possessing a very low content in the raw coal, are vital for the agglomeration of ash particles, which are also highly sensitive to the loading of gas impurities in flue gas. HCl recirculation is the most crucial factor promoting the vaporisation of metals via chlorination. Apart from alkali metals, the organically bound Al and Ti were also vaporised noticeably. Recirculation of SO{sub 2} promoted the sulfation of Na to condense into liquid droplet which increased fine ash yield. Co-existence of bulk HCl and SO{sub 2} played a synergetic role in the sulfation of Na via an initial chlorination of the char-bound Na. In contrast, co-existence of steam with HCl and SO{sub 2} favored the formation of Na alumino-silicates, which are favorable for ash agglomeration. 34 refs., 15 figs., 3 tabs.

  12. COFIRING BIOMASS WITH LIGNITE COAL; FINAL

    International Nuclear Information System (INIS)

    Darren D. Schmidt

    2002-01-01

    The University of North Dakota Energy and Environmental Research Center, in support of the U.S. Department of Energy's (DOE) biomass cofiring program, completed a Phase 1 feasibility study investigating aspects of cofiring lignite coal with biomass relative to utility-scale systems, specifically focusing on a small stoker system located at the North Dakota State Penitentiary (NDSP) in Bismarck, North Dakota. A complete biomass resource assessment was completed, the stoker was redesigned to accept biomass, fuel characterization and fireside modeling tests were performed, and an engineering economic analysis was completed. In general, municipal wood residue was found to be the most viable fuel choice, and the modeling showed that fireside problems would be minimal. Experimental ash deposits from firing 50% biomass were found to be weaker and more friable compared to baseline lignite coal. Experimental sulfur and NO(sub x) emissions were reduced by up to 46%. The direct costs savings to NDSP, from cogeneration and fuel saving, results in a 15- to 20-year payback on a$1,680,000 investment, while the total benefits to the greater community would include reduced landfill burden, alleviation of fees for disposal by local businesses, and additional jobs created both for the stoker system as well as from the savings spread throughout the community

  13. A lignite-geothermal hybrid power and hydrogen production plant for green cities and sustainable buildings

    Energy Technology Data Exchange (ETDEWEB)

    Kilkis, B. [Baskent University, Ankara (Turkey). Dept. of Mechanical Engineering

    2011-02-15

    Turkey is rich in both geothermal energy and lignite reserves, which in many cases, are co-located. This condition makes it feasible to utilize both lignite and geothermal energy in a hybrid form for combined power heat, and cold generation, which may lead to optimally energy and exergy efficient, environmentally benign, and economically sound applications. This paper presents a novel concept of hybrid lignite-geothermal plant for a district energy system and hydrogen production facility in Aydin with special emphasis on high performance, green buildings and green districts. In this concept, lignite is first introduced to a partially fluidized-bed gasifier and then to a fluidized-bed gas cleaning unit, which produces synthetic gas and finally hydrogen. The by-products, namely char and ash are used in a fluidized-bed combustor to produce power. Waste heat from all these steps are utilized in a district heating system along with heat received from geothermal production wells after power is generated there. H{sub 2}S gas obtained from the separator system is coupled with hydrogen production process at the lignite plant. Absorption cooling systems and thermal storage tanks complement the hybrid system for the tri-generation district energy system. On the demand side, the new, green OSTIM OSB administration building in Ankara is exemplified for greener, low-exergy buildings that will compound the environmental benefits.

  14. Research on the thermal decomposition of Mongolian Baganuur lignite and Naryn sukhait bituminous coal

    Directory of Open Access Journals (Sweden)

    A. Ariunaa

    2016-03-01

    Full Text Available The technical characteristics, elemental composition of the organic and mineral matters, ash melting behaviors and carbonization and gasification reactivities of coals from Baganuur and Naryn sukhait deposits were investigated. The results of proximate and ultimate analysis confirmed that the coal from Baganuur deposit can be graded as a low rank lignite B2 mark coal and Naryn sukhait coal is a bituminous G mark one. The carbonization and gasification experiments were performed using TGA apparatus and fixed bed quartz reactor. The data obtained with two experimental reactors showed that Baganuur lignite had lower thermal stability and much higher CO2 gasification reactivity at 950°C as compared to those for Naryn sukhait bituminous coal.Mongolian Journal of Chemistry 16 (42, 2015, 22-29

  15. Lignite Fuel Enhancement

    Energy Technology Data Exchange (ETDEWEB)

    Charles Bullinger; Nenad Sarunac

    2010-03-31

    Pulverized coal power plants which fire lignites and other low-rank high-moisture coals generally operate with reduced efficiencies and increased stack emissions due to the impacts of high fuel moisture on stack heat loss and pulverizer and fan power. A process that uses plant waste heat sources to evaporate a portion of the fuel moisture from the lignite feedstock in a moving bed fluidized bed dryer (FBD) was developed in the U.S. by a team led by Great River Energy (GRE). The demonstration was conducted with Department of Energy (DOE) funding under DOE Award Number DE-FC26-04NT41763. The objectives of GRE's Lignite Fuel Enhancement project were to demonstrate reduction in lignite moisture content by using heat rejected from the power plant, apply technology at full scale at Coal Creek Station (CCS), and commercialize it. The Coal Creek Project has involved several stages, beginning with lignite drying tests in a laboratory-scale FBD at the Energy Research Center (ERC) and development of theoretical models for predicting dryer performance. Using results from these early stage research efforts, GRE built a 2 ton/hour pilot-scale dryer, and a 75 ton/hour prototype drying system at Coal Creek Station. Operated over a range of drying conditions, the results from the pilot-scale and prototype-scale dryers confirmed the performance of the basic dryer design concept and provided the knowledge base needed to scale the process up to commercial size. Phase 2 of the GRE's Lignite Fuel Enhancement project included design, construction and integration of a full-scale commercial coal drying system (four FBDs per unit) with Coal Creek Units 1 and 2 heat sources and coal handling system. Two series of controlled tests were conducted at Coal Creek Unit 1 with wet and dried lignite to determine effect of dried lignite on unit performance and emissions. Wet lignite was fired during the first, wet baseline, test series conducted in September 2009. The second test series was

  16. Atmospheric Fluidized Bed Combustion testing of North Dakota lignite

    Energy Technology Data Exchange (ETDEWEB)

    Goblirsch, G; Vander Molen, R H; Wilson, K; Hajicek, D

    1980-05-01

    The sulfur retention by the inherent alkali, and added limestone sorbent, perform about the same and are reasonably predictable within a range of about +-10% retention by application of alkali to sulfur ratio. Temperature has a substantial effect on the retention of sulfur by the inherent alkali or limestone. The temperature effect is not yet fully understood but it appears to be different for different coals and operational conditions. The emission of SO/sub 2/ from the fluid bed burning the Beulah lignite sample used for these tests can be controlled to meet or better the current emission standards. The injection of limestone to an alkali-to-sulfur molar ratio of 1.5 to 1, should lower the SO/sub 2/ emissions below the current requirement of 0.6 lb SO/sub 2//10/sup 6/ Btu to 0.4 lb SO/sub 2//10/sup 6/ Btu, a safe 33% below the standard. Agglomeration of bed material, and consequent loss of fluidization quality can be a problem when burning high sodium lignite in a silica bed. There appears, however, to be several ways of controlling the problem including the injection of calcium compounds, and careful control of operating conditions. The heat transfer coefficients measured in the CPC and GFETC tests are comparable to data obtained by other researchers, and agree reasonably well with empirical conditions. The NO/sub x/ emissions measured in all of the tests on Beulah lignite are below the current New Source Performance Standard of 0.5 lb NO/sub 2//10/sup 6/ Btu input. Combustion efficiencies for the Beulah lignite are generally quite high when ash recycle is being used. Efficiencies in the range of 98% to 99%+ have been measured in all tests using this fuel.

  17. Co-pyrolysis of lignite and sugar beet pulp

    International Nuclear Information System (INIS)

    Yilgin, M.; Deveci Duranay, N.; Pehlivan, D.

    2010-01-01

    Today, worldwide studies have been undertaken on the biomass usage and co-conversion of biomass and coal to seek out alternative fuels for supplying energy in an environmental friendly way. The objective of this work is to study co-pyrolysis of lignite and sugar beet pulp in 50/50 (wt./wt.) ratio of blend pellets, to elucidate their thermal behaviour under pyrolysis conditions and to assess major decomposition products in terms of their yields. A special chamber, which has enabled very fast heating rates, was used in the pyrolysis experiments carried at 600 deg. C. The results were interpreted in the light of liquid, solid and gaseous yields, resulting from thermal decomposition, and kinetics of thermogravimetric analysis. Proximate volatile matter and ash contents of the blends were different compared to those found by using individual values. Sugar beet pulp decomposed faster within a relatively narrow temperature range than lignite and underwent a significant shrinkage during pyrolysis. It was found that the chars left behind after the flash pyrolysis of these pellets at 600 deg. C have substantial amounts of volatile matter that would evolve upon further heating.

  18. FBC: a flat binary code scheme for fast Manhattan hash retrieval

    Science.gov (United States)

    Kong, Yan; Wu, Fuzhang; Gao, Lifa; Wu, Yanjun

    2018-04-01

    Hash coding is a widely used technique in approximate nearest neighbor (ANN) search, especially in document search and multimedia (such as image and video) retrieval. Based on the difference of distance measurement, hash methods are generally classified into two categories: Hamming hashing and Manhattan hashing. Benefitting from better neighborhood structure preservation, Manhattan hashing methods outperform earlier methods in search effectiveness. However, due to using decimal arithmetic operations instead of bit operations, Manhattan hashing becomes a more time-consuming process, which significantly decreases the whole search efficiency. To solve this problem, we present an intuitive hash scheme which uses Flat Binary Code (FBC) to encode the data points. As a result, the decimal arithmetic used in previous Manhattan hashing can be replaced by more efficient XOR operator. The final experiments show that with a reasonable memory space growth, our FBC speeds up more than 80% averagely without any search accuracy loss when comparing to the state-of-art Manhattan hashing methods.

  19. Sedimentary cycles and volcanic ash beds in the Lower Pliocene lacustrine succession of Ptolemais (NW Greece): discrepancy between 40 Ar/39 Ar and astronomical ages

    NARCIS (Netherlands)

    Steenbrink, J.; Vugt, N. van; Hilgen, F.J.; Wijbrans, J.R.; Meulenkamp, J.E.

    1999-01-01

    A high-resolution cyclostratigraphy for the rhythmically bedded lignite-marl sequences of the Lower Pliocene Ptole-mais Formation is combined with 40 Ar= 39 Ar dating results of intercalated volcanic ash beds. Detailed field reconnaissance in three open-pit lignite mines reveals three end-member

  20. Technology and use of lignite. Proceedings of the tenth biennial lignite symposium

    Energy Technology Data Exchange (ETDEWEB)

    Kube, W. R.; Gronhovd, G. H. [comps.

    1979-01-01

    The symposium on the technology and use of lignite was sponsored by the US Department of Energy and the University of North Dakota, and held at Grand Forks, North Dakota, May 30-31, 1979. Twenty-one papers from the proceedings of this tenth biennial lignite symposium have been entered into EDB and ERA and three also into EAPA. The papers discuss lignite deposits in the USA, mining plans, gasification and in-situ gasification, and combustion in fossil-fuel power plants. (LTN)

  1. The North Dakota lignite partnership

    International Nuclear Information System (INIS)

    Porter, C.R.

    1998-01-01

    The State of North Dakota and the Lignite Energy Council have formed a government/industry partnership to promote the use of North Dakota lignite. The partnership provides funding and management for the Lignite Research, Development and Marketing Program. The program funds activities which preserve and enhance jobs and lignite production; ensure economic growth, stability and opportunity; and maintain a stable and competitive tax base. Funding is provided for activities in three areas: marketing feasibility studies, small research projects, and demonstration projects. Funding is derived from the state coal severance tax. Approximately $3,000,000 annually is appropriated from coal severance revenues for program activities. North Dakota is the ninth largest coal producing state, with lignite as the only rank of coal found in the state. Energy is the second largest economic sector in North Dakota, and it currently comprises over 12% of the state's total economic base. This paper reviews the North Dakota lignite industry and describes studies and projects which have received funding from the program

  2. Ash chemistry and sintering, verification of the mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Hupa, M.; Skrifvars, B.J. [Aabo Akademi, Turku (Finland)

    1996-12-01

    In this project four sintering mechanisms have been studied, i.e., partial melting with a viscous liquid, partial melting with a non-viscous liquid, chemical reaction sintering and solid state sintering. The work has aimed at improving the understanding of ash sintering mechanisms and quantifying their role in combustion and gasification. The work has been oriented in particular on the understanding of biomass ash behavior. The work has not directly focused on any specific technical application. However, results can also be applied on other fuels such as brown coal, petroleum coke, black liquor and different types of wastes (PDF, RDF, MSW). In one part of study the melting behavior was calculated for ten biomass ashes and compared with lab measurements of sintering tendencies. The comparison showed that the T{sub 15} temperatures, i.e. those temperatures at which the ashes contained 15 % molten phase, correlated fairly well with the temperature at which the sintering measurements detected sintering. This suggests that partial melting can be predicted fairly accurate for some ashes already with the today existing thermodynamic calculation routines. In some cases, however the melting calculations did not correlate with the detected sintering temperatures. In a second part detailed measurements on ash behavior was conducted both in a semi full scale CFB and a lab scale FBC. Ashes and deposits were collected and analyzed in several different ways. These analyses show that the ash chemistry shifts radically when the fuel is shifted. Fuels with silicate based ashes behaved totally different than those with an oxide or salt based ash. The chemistry was also affected by fuel blending. The ultimate goal has been to be able to predict the ash thermal behavior during biomass thermal conversion, using the fuel and ash elemental analyses and a few operational key parameters as the only input data. This goal has not yet today been achieved. (author)

  3. Mercury Control for Plants Firing Texas Lignite and Equipped with ESP-wet FGD

    Energy Technology Data Exchange (ETDEWEB)

    Katherine Dombrowski

    2009-12-31

    This report presents the results of a multi-year test program conducted as part of Cooperative Agreement DE-FC26-06NT42779, 'Mercury Control for Plants Firing Texas Lignite and Equipped with ESP-wet FGD.' The objective of this program was to determine the level of mercury removal achievable using sorbent injection for a plant firing Texas lignite fuel and equipped with an ESP and wet FGD. The project was primarily funded by the U.S. DOE National Energy Technology Laboratory. EPRI, NRG Texas, Luminant (formerly TXU), and AEP were project co-funders. URS Group was the prime contractor, and Apogee Scientific and ADA-ES were subcontractors. The host site for this program was NRG Texas Limestone Electric Generating Station (LMS) Units 1 and 2, located in Jewett, Texas. The plant fires a blend of Texas lignite and Powder River Basin (PRB) coal. Full-scale tests were conducted to evaluate the mercury removal performance of powdered sorbents injected into the flue gas upstream of the ESP (traditional configuration), upstream of the air preheater, and/or between electric fields within the ESP (Toxecon{trademark} II configuration). Phases I through III of the test program, conducted on Unit 1 in 2006-2007, consisted of three short-term parametric test phases followed by a 60-day continuous operation test. Selected mercury sorbents were injected to treat one quarter of the flue gas (e.g., approximately 225 MW equivalence) produced by Limestone Unit 1. Six sorbents and three injection configurations were evaluated and results were used to select the best combination of sorbent (Norit Americas DARCO Hg-LH at 2 lb/Macf) and injection location (upstream of the ESP) for a two-month performance evaluation. A mercury removal rate of 50-70% was targeted for the long-term test. During this continuous-injection test, mercury removal performance and variability were evaluated as the plant operated under normal conditions. Additional evaluations were made to determine any

  4. Catalytic effect of mineral matter of high ash Onakawana lignite on steam gasification

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E.

    1986-04-01

    Reactivities of untreated and acid washed Onakawana lignite during steam gasification were compared in a thermobalance reactor. The acid treatment resulted in removal of Ca, Mg, Ba and Sr from mineral matter. This was accompanied by a marked decrease in the rates of H/sub 2/, CO and CO/sub 2/ formation. The decrease of gasification rate was attributed to the decrease in concentration of gasification sites during the acid treatment.

  5. Chemical mass balance source apportionment of TSP in a lignite-burning area of Western Macedonia, Greece

    Science.gov (United States)

    Samara, Constantini

    Total suspended particle mass concentrations (TSP) were determined in the Kozani-Ptolemais-Florina basin (western Macedonia, Greece), an area with intensive lignite burning for power generation. The study was conducted over a 1-year period (November 2000-November 2001) at 10 receptor sites located at variable distances from the power plants. Ambient TSP samples were analyzed for 27 major, minor and trace elements. Particulate emissions were also collected from a variety of sources including fly ash, lignite dust, automobile traffic, domestic heating, and open-air burning of agricultural biomass and refuse, and analyzed for the same chemical components. Ambient and source chemical profiles were used for source identification and apportionment of TSP by employing a chemical mass balance (CMB) receptor model. Diesel burning in vehicular traffic and in the power plants for generator start up was found to be the major contributor to ambient TSP levels at all 10 sites. Other sources with significant contributions were domestic coal burning, vegetative burning (wood combustion and agricultural burns) and refuse open-air burning. Fly ash escaping the electrostatic precipitators of the power plants was a minor contributor to ambient TSP.

  6. Advanced power assessment for Czech lignite. Task 3.6, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Sondreal, E.A.; Mann, M.D.; Weber, G.W.; Young, B.C.

    1995-12-01

    The US has invested heavily in research, development, and demonstration of efficient and environmentally acceptable technologies for the use of coal. The US has the opportunity to use its leadership position to market a range of advanced coal-based technologies internationally. For example, coal mining output in the Czech Republic has been decreasing. This decrease in demand can be attributed mainly to the changing structure of the Czech economy and to environmental constraints. The continued production of energy from indigenous brown coals is a major concern for the Czech Republic. The strong desire to continue to use this resource is a challenge. The Energy and Environmental Research Center undertook two major efforts recently. One effort involved an assessment of opportunities for commercialization of US coal technologies in the Czech Republic. This report is the result of that effort. The technology assessment focused on the utilization of Czech brown coals. These coals are high in ash and sulfur, and the information presented in this report focuses on the utilization of these brown coals in an economically and environmentally friendly manner. Sections 3--5 present options for utilizing the as-mined coal, while Sections 6 and 7 present options for upgrading and generating alternative uses for the lignite. Contents include Czech Republic national energy perspectives; powering; emissions control; advanced power generation systems; assessment of lignite-upgrading technologies; and alternative markets for lignite.

  7. Environmental assessment of remedial action at the inactive uraniferous lignite processing sites at Belfield and Bowman, North Dakota

    International Nuclear Information System (INIS)

    Beranich, S.; Berger, N.; Bierley, D.; Bond, T.M.; Burt, C.; Caldwell, J.A.; Dery, V.A.; Dutcher, A.; Glover, W.A.; Heydenburg, R.J.; Larson, N.B.; Lindsey, G.; Longley, J.M.; Millard, J.B.; Miller, M.; Peel, R.C.; Persson-Reeves, C.H.; Titus, F.B.; Wagner, L.

    1989-09-01

    The Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA), to clean up the Belfield and Bowman, North Dakota, uraniferous lignite processing sites to reduce the potential health impacts associated with the residual radioactive materials remaining at these sites. Remedial action at these sites must be performed in accordance with the US Environmental Protection Agency's (EPA) standards promulgated for the remedial action and with the concurrence of the US Nuclear Regulatory Commission (NRC) and the state of North Dakota. The inactive Belfield uraniferous lignite processing site is one mile southeast of Belfield, North Dakota. The inactive Bowman uraniferous lignite processing site at the former town of Griffin, is seven miles northwest of Bowman, North Dakota and 65 road miles south of Belfield. Lignite ash from the processing operations has contaminated the soils over the entire 10.7-acre designated Belfield site and the entire 12.1-acre designated Bowman site. Dispersion of the ash has contaminated an additional 20.6 acres surrounding the Belfield processing site and an additional 59.2 acres surrounding the Bowman processing site. The proposed remedial action is to relocate the contaminated materials at the Belfield processing site to the Bowman processing/disposal site for codisposal with the Bowman contaminated soils. The environmental impacts assessed in this EA were evaluated for the proposed remedial action and the no action alternative and demonstrate that the proposed action would not significantly affect the quality of the human environment and would be performed in compliance with applicable environmental laws. The no action alternative would not be consistent with the intent of Public Law 95-604 and would not comply with the EPA standards. 48 refs., 10 figs., 7 tabs

  8. Lignite in North Dakota

    International Nuclear Information System (INIS)

    Porter, C.R.

    1995-01-01

    The State of North Dakota and the lignite industry are working together in a partnership called the Lignite Research, Development and Marketing Program. The program provides funds and supports activities which: preserve and enhance jobs and lignite production; ensure economic growth, stability and opportunity; and maintain a stable and competitive tax base. Since 1987, 70 grants totaling $24 million have been awarded. Each program dollar has resulted in nearly five of matching dollars. These program investments have yielded returns for the state and industry, including an additional $20 million annually from by-products at the Great Plains Synfuels Plant; about $1 million annually from improved reclamation practices; and combustion options, which preserve 2,000 megawatts of existing generation capacity. Research activities have identified future opportunities, including: the SynCoal demonstration plant, requiring 800,000 tons per year of new production; new chemical feedstock by-products from Great Plains worth an additional $26 million annually; revised reclamation practices that could substantially reduce cost; and potential new markets for upgraded lignite of about 12 million tons annually. This program helps ensure a healthy future for the North Dakota lignite industry, which currently represents 10% of the state's total economic base. Such a program is important because it will encourage the development of new and better uses of North Dakota's most abundant resource--lignite coal

  9. Lignite; Braunkohle

    Energy Technology Data Exchange (ETDEWEB)

    Kaltenbach, Erwin; Maassen, Uwe [Debriv e.V., Berlin und Koeln (Germany)

    2015-07-01

    The domestic lignite is the most important and in the foreseeable future, the only domestic energy resource that is available in large quantities and economically. It makes an essential contribution to secure and competitive energy supply and has a high regional as macroeconomic importance. The required guarantied capacity for the development of renewable energy, the lignite provides under competition conditions. The flexibility of the lignite power plants is in addition to security of supply and competitiveness, a strategic added value for a reliable power supply. [German] Die heimische Braunkohle ist die wichtigste und in ueberschaubarer Zukunft auch die einzige heimische Energieressource, die in grossen Mengen und wirtschaftlich zur Verfuegung steht. Sie leistet einen unverzichtbaren Beitrag zur sicheren und wettbewerbsfaehigen Energieversorgung und hat eine hohe regional- wie gesamtwirtschaftliche Bedeutung. Die fuer den Ausbau der erneuerbaren Energien notwendige gesicherte Leistung stellt die Braunkohle unter Wettbewerbsbedingungen zur Verfuegung. Die Flexibilitaet des Braunkohlenkraftwerksparks ist neben Versorgungssicherheit und Wettbewerbsfaehigkeit ein strategischer Zusatznutzen fuer eine sichere Stromversorgung.

  10. Externalities from lignite mining-related dust emissions

    International Nuclear Information System (INIS)

    Papagiannis, A.; Roussos, D.; Menegaki, M.; Damigos, D.

    2014-01-01

    During the last three decades, several studies have been conducted in order to assess the external costs of electricity production from fossil fuels, especially coal and lignite. Nevertheless, these studies usually ignore the impacts generated by the upstream mining works. This paper contributes to existing literature and attempts to fill this gap by exploring the externalities of lignite mining owing to the emission of suspended particulate matter. To this end, a ‘bottom-up’ approach is implemented, using as case study the largest operational lignite surface mine at the Lignite Center of Western Macedonia (Greece). The results indicate that annual air pollution externalities of lignite mining are of the order of 3€/ton of lignite, which corresponds to around 5.0 €/MW h. The estimated costs are significantly lower, i.e. up to 80%, when dust deposition is considered in air dispersion models. In any case, these findings should be seen as a starting point for discussion owing to the lack of specific emission rates for Greek lignite mines. - Highlights: • Externalities from lignite mining-related dust emissions are 3 €/t of lignite. • Externalities of mining correspond to around 5.0 €/MW h. • Externalities are significantly lower, up to 80%, if dust deposition is considered. • There is lack of specific dust emission rates for lignite mining. • There are high discrepancies in existing dust emission rates for lignite mining

  11. Neyveli lignite - a status overview

    Energy Technology Data Exchange (ETDEWEB)

    Tandon, G L

    1984-11-14

    The lignite mines of the Neyveli Lignite Corporation in Tamil Nadu in India are described: characteristics of the deposit; choice of mining method (surface mining); groundwater control; storm water control; overburden removal; mining equipment (bucket wheel excavators, belt conveyors and spreaders); generation of electric power; production of fertilizer; production of lignite briquettes and tar products. A second mine and thermal power plant are planned.

  12. Model-Based Water Wall Fault Detection and Diagnosis of FBC Boiler Using Strong Tracking Filter

    Directory of Open Access Journals (Sweden)

    Li Sun

    2014-01-01

    Full Text Available Fluidized bed combustion (FBC boilers have received increasing attention in recent decades. The erosion issue on the water wall is one of the most common and serious faults for FBC boilers. Unlike direct measurement of tube thickness used by ultrasonic methods, the wastage of water wall is reconsidered equally as the variation of the overall heat transfer coefficient in the furnace. In this paper, a model-based approach is presented to estimate internal states and heat transfer coefficient dually from the noisy measurable outputs. The estimated parameter is compared with the normal value. Then the modified Bayesian algorithm is adopted for fault detection and diagnosis (FDD. The simulation results demonstrate that the approach is feasible and effective.

  13. Speciation of Zinc in ash investigated by X-ray absorption spectroscopy; Zinks foerekomstformer i aska studerade med en roentgenabsorptionsspektrometrisk metod

    Energy Technology Data Exchange (ETDEWEB)

    Steenari, Britt-Marie; Noren, Katarina

    2008-06-15

    neighbour, but also about the next scattering shell of atoms surrounding the central zinc atom. The EXAFS data and modelling results showed that the most common zinc species in wood fuel ashes from FBC boilers are silicate, aluminate and to a lesser extent hydroxide. It cannot be ruled out that zinc can be bound as ZnO but this form is not dominant. This is the case for both bottom ashes and fly ashes. In one of the FBC boilers (BFB-bio), elementary sulphur is added in order to abate corrosion problems. Both bottom ash and fly ash from that combustor showed indications of the presence of ZnS or ZnCl{sub 2}. It is difficult to distinguish between Zn-S and Zn-Cl distances be EXAFS, but since zinc chloride is not likely to be stable in a combustor bed the conclusion was drawn that some zinc had been bound as sulphide in the bottom ash. The filter ash, however, might contain both sulphide and chloride in small amounts. Kaolin was used as an anti-sintering additive during a test period in the wood fuelled CFB included in this work. The general results from this test period has been published elsewhere but it is interesting for this investigation to note that the kaolin absorbed potassium that otherwise should have formed gaseous KCl and thus, left some more HCl in the flue gas free to react with other metal species in the burning fuel. In addition, it was noted that the kaolin was concentrated in the fly ash as was potassium and zinc. The EXAFS data for this fly ash showed the presence of ZnCl{sub 2} and/or ZnS. Due to the increased presence of HCl in the flue gas zinc chloride is most likely compound. However, it was only present in a small amount and the main part of the Zn was found as silicate. In the fly ash from normal operation of the boiler no zinc chloride was found. Wood ash that had been moistened and aged was shown to contain zinc in silicate, hydroxide and/or aluminate forms. In one sample of an ash the had been aged outdoors for only 0.5 years indication of minor

  14. THE COMBUSTION CHARACTERISTICS OF LIGNITE BLENDS

    Institute of Scientific and Technical Information of China (English)

    Cheng Jun; Zhou Junhu; Cao Xinyu; Cen Kefa

    2000-01-01

    The combustion characteristics of lignite blends were studied with a thermogravimetric analyzer (t.g.a.), at constant heating rate.The characteristic temperatures were determined from the burning profiles.It was found that the characteristic times of combustion reaction moved forward, the ignition temperature dropped and the burnout efficiency slightly changed when blending lignites.The characteristic parameters of blends could not be predicted as a linear function of the average values of the individual lignites.when blending with less reactive coal, the ignition and burnout characteristics of lignite turned worse.

  15. Fundamental study of low-NOx combustion fly ash utilization

    International Nuclear Information System (INIS)

    Suuberg, Eric M.; Hurt, Robert H.

    1998-01-01

    This study is principally concerned with characterizing the organic part of coal combustion fly ashes. High carbon fly ashes are becoming more common as by-products of low-NOx combustion technology, and there is need to learn more about this fraction of the fly ash. The project team consists of two universities, Brown and Princeton, and an electrical utility, New England Power. A sample suite of over fifty fly ashes has been gathered from utilities across the United States, and includes ashes from a coals ranging in rank from bituminous to lignite. The characterizations of these ashes include standard tests (LOI, Foam Index), as well as more detailed characterizations of their surface areas, porosity, extractability and adsorption behavior. The ultimate goal is, by better characterizing the material, to enable broadening the range of applications for coal fly ash re-use beyond the current main market as a pozzolanic agent for concretes. The potential for high carbon-content fly ashes to substitute for activated carbons is receiving particular attention. The work performed to date has already revealed how very different the surfaces of different ashes produced by the same utility can be, with respect to polarity of the residual carbon. This can help explain the large variations in acceptability of these ashes as concrete additives

  16. Organic petrology, mineralogy and depositional environment of the Kipra lignite seam, Maritza-West basin, Bulgaria

    Energy Technology Data Exchange (ETDEWEB)

    Kostova, Irena [Department of Geology and Palaeontology, Sofia University ' ' St. Kliment Ohridski' ' , 1000, Sofia (Bulgaria); Zdravkov, Alexander [Department of Economic Geology, University of Mining and Geology ' ' St. Ivan Rilski' ' , 1700, Sofia (Bulgaria)

    2007-08-01

    The aim of the present study is to provide additional information about the properties and depositional environment of the Kipra lignite seam, which was deposited during the regressive stage of development of the Maritza-West basin. Petrographical and mineralogical data, along with ash yields and sulphur contents of 24 samples from a seam profile, have been used to study the vertical variation of the depositional settings during peat accumulation and subsequent coalification. The Kipra lignite is characterized by high ash yields and sulphur contents. It formed in a rheotrophic, low-lying mire with alkaline pH value. Vegetation with low preservation potential dominated within the palaeomire. During peat formation, frequent changes of the water level controlled the depositional environment. During the deposition of units 1 and 2, high water energy caused the transportation of high amounts of inorganic material into the mire, resulting in the formation of weakly gelified mineral-rich lignite. The organic matter from units 3 and 4 is characterized by enhanced gelification, which probably reflects the decreasing energy of the system. Good positive correlation between sulphur contents and the GI values was established in units 4, indicating that the gelification of the tissues was probably mainly controlled by the bacterial activity. In contrast, the gelification of the samples from unit 3 of the Kipra seam was probably governed by the redox conditions. The organic matter deposited under relatively wet conditions, in which the thermal and oxidative destruction of the tissues, was limited. A variety of major, minor and accessory minerals are present in Maritza-West lignite. The mineral composition is dominated mainly by pyrite, gypsum and calcite, and to a lesser extent limonite, quartz, kaolinite, montmorillonite, illite, chlorite and plagioclase. Jarosite, hematite, halloysite, mica, K-feldspar, aragonite, siderite, and dolomite were also determined in very low

  17. Influence of the co-firing on the leaching of trace pollutants from coal fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Maria Izquierdo; Natalia Moreno; Oriol Font; Xavier Querol; Esther Alvarez; Diano Antenucci; Henk Nugteren; Yolanda Luna; Constantino Fernandez-Pereira [Institute of Earth Sciences ' Jaume Almera' (CSIC), Barcelona (Spain)

    2008-08-15

    The (co)-firing of low-cost alternative fuels is expected to increase in the forthcoming years in the EU because of the economic and environmental benefits provided by this technology. This study deals with the impact of the different coal/waste fuel ratio of the feed blend on the mineralogy, the chemical composition and especially on the leaching properties of fly ash. Different blends of coal, petroleum coke, sewage sludge, wood pellets, coal tailings and other minor biomass fuels were tested in PCC (pulverised coal combustion) and FBC (fluidized bed combustion) power plants. The co-firing of the studied blends did not drastically modify the mineralogy, bulk composition or the overall leaching of the fly ash obtained. This suggests that the co-firing process using the alternative fuels studied does not entail significant limitations in the re-use or management strategies of fly ash. 34 refs., 4 figs., 3 tabs.

  18. Lignite utilisation for binding of radionuclides and uranium determination by adsorptive stripping chronopotentiometry

    International Nuclear Information System (INIS)

    Zavodska, L.

    2010-01-01

    This work in its first part deals with non-energetic use of young brown coal - lignite. The goal of the work was to perform a complex physical and chemical characterisation of the Slovak lignite (deposit Cary) which could contribute to rts use in binding of radionuclides in the environment. The characteristics of Slovak lignite were compared to leonardite (Gascoyne, USA) and Czech lignite (the area of Mikulcice). In the samples the residual humidity was determined. as well. as the content of ashes. representation of selected inorganic (As, Ba, Cd, Co, Cr, Cu, Ni, Pb and Zn) as well as organo-elements (C, H, N, 0, S) and crystalline forms of inorganic phase in lignite. The specific surface (BET isotherm) of lignite was determined, representation of total and free humic acids and their cation exchange capacity. The samples underwent al.so gamma-spectrometric analysis ( 40 K, 226 Ra, 228 Ac, 137 Cs and 60 Co). Using the radio-indicator method ( 85 Sr and 137 Cs) the kinetics of sorption of Cs + and Sr + ions in Slovak lignite was studied. The efficiency of sorption for both cations on lignite was evaluated on the basis of constructed sorption isotherms. The sorption of Cs + ions on Slovak lignite is more suitable for the Freundlich type of isotherm, in case of Sr + ions the sorption is better described by Langmuir isotherm. The results of sorption experiments on lignite in comparison with clinoptilolite and montmorillonite K-10 showed a more efficient sorption for Sr Ions. despite the more coarse-grained fraction of this matrix. This finding supports the possibility of lignite application for binding of a quite mobile radiostrontium, which may be applied for construction of radioactive waste repositories or for remediation of contaminated soils. The second part of the work deals with the development and validation of new fast and reliable electrochemical method of uranium determination in natural waters. It is based on physical adsorption of created complex of uranium

  19. Investigation of the possibility of binding fly ash particles by elemental sulphur

    Directory of Open Access Journals (Sweden)

    Vidojković V.

    2006-01-01

    Full Text Available Thermal power plants in Serbia use lignite for electrical power production The secondary product of coal combustion is fly ash in the amount of 17%. Fly ash causes the pollution of air, water and soil, and also cause many human, especially lung diseases. Secondary sulphur is a product of crude oil refining. The aim of this study was to investigate the use of sulphur as a bonding material in ultra fine particle agglomeration (smaller than 63 μm in fly ash. The agglomeration should make the ash particles larger and heavy enough to fall without flying fractions. The experiments showed that during the homogenization of the ashes and sulphur from 150 to 170 °C in a reactor with intensive mixing, an amount of 15% sulphur was sufficient to bond particles and cause agglomeration without visible flying fractions.

  20. Lignite boost for North. [Northern Ireland

    Energy Technology Data Exchange (ETDEWEB)

    Clerkin, H.

    1986-01-01

    Reserves of lignite, estimated at around 500 million tonnes, have been discovered on the shores of Lough Neagh, Northern Ireland. The Government has granted a mining licence and planning permission to Burnett and Hallamshire Holdings to start work on the deposit. It is proposed to mine the lignite using opencast methods. Much of this deposit will be consumed in a purpose-built mine mouth power station with further reserves being dried in the approved processing plant to produce a range of industrial and domestic fuels. Carbonising the lignite may eliminate pollution. However, large scale investment will be required before Ireland's economy can switch to lignite.

  1. Lignite mining in India - technology highlights

    Energy Technology Data Exchange (ETDEWEB)

    Tandon, G L

    1984-01-01

    Figures for lignite production and its role in the Indian energy scene are presented. Lignite mining at Neyveli is described in detail, including: advance preparation of the overburden strata; modifications to bucket wheel excavators; tackling the sticky surface clays; ground water management; storm water control; tackling higher overburden-to-lignite ratios; materials handling; communications within the mine; the development of indigenous mining equipment; and ecology and environmental control.

  2. Microbial activities in forest soils exposed to chronic depositions from a lignite power plant

    Energy Technology Data Exchange (ETDEWEB)

    Klose, S.; Wernecke, K.D.; Makeschin, F. [Technical University of Dresden, Tharandt (Germany)

    2004-12-01

    Atmospheric emissions of fly ash and SO{sub 2} from lignite-fired power plants strongly affect large forest areas in Germany. The impact of different deposition loads on the microbial biomass and enzyme activities was studied at three forest sites (Picea abies (L.) Karst.) along an emission gradient of 3, 6, and 15 km downwind of a coal-fired power plant, representing high, moderate and low emission rates. An additional site at a distance of 3 km from the power plant was chosen to study the influence of forest type on microbial parameters in coniferous forest soils under fly ash and SO{sub 2} emissions. Soil microbial biomass C and N, CO{sub 2} evolved and activities of L-asparaginase, L-glutaminase, beta-glucosidase, acid phosphatase and arylsulfatase (expressed on dry soil and organic C basis) were determined in the forest floor (L, Of and Oh horizon) and mineral top soil (0-10 cm). It is concluded that chronic fly ash depositions decrease litter decomposition by influencing specific microbial and enzymatic processes in forest soils.

  3. Macedonian lignite - upgrading and evaluation

    International Nuclear Information System (INIS)

    Musich, Mark A.; Young, Brian C.

    1997-01-01

    Macedonian lignites have a high moisture content, low heating value, and are friable, generating fines and dust. Macedonia has an urgent need to use indigenous solid fuel resources for domestic and industrial heating as well as metallurgical applications. The goal of this project was to evaluate the potential for beneficiating Macedonian lignite and producing high-quality briquettes for metallurgical use as well as domestic/industrial heating. Laboratory studies have shown that treating the Macedonian lignite fines by two physical processes-cleaning and carbonization-followed by pelletizing. can generate acceptable lump fuels for heating applications. Carbonizing the float-sink-cleaned lignite to reduce the volatile matter content and pelletizing the resultant char with starch produced strong pellets, which could be used as a home-heating fuel, the char having a heat content of 13,400 Btu/lb (31.2 MJ/Kg). However, additional work is required at the pilot scale to determine optimum briquetting conditions and production costs. (Author)

  4. Utilization of lignite power generation residues for the production of lightweight aggregates.

    Science.gov (United States)

    Anagnostopoulos, Iason M; Stivanakis, Victor E

    2009-04-15

    A novel process is proposed for the utilization of lignite combustion solid residues in the production of inflammable lightweight aggregates (LWA). The process consists of two stages, pelletization and sintering, and carbon contained in BA was used as the process fuel. The main residues bottom ash (BA) and fly ash (FA) from Megalopolis power plant were characterized, mixed in different proportions and treated through pelletization and sintering process. Sintering benefits from combustion of BA carbon content and the product is a hardened porous cake. The energy required for achievement of high temperatures, in the range of 1250 degrees C, was offered by carbon combustion and CO(2) evolution is responsible for porous structure formation. Selected physical properties of sintered material relevant to use as lightweight aggregates were determined, including bulk density, porosity and water absorption. Bulk density varies from 0.83 to 0.91 g/cm(3), porosity varies from 60% to 64% and water absorption varies from 66% to 80%. LWA formed is used for the production of lightweight aggregate concrete (LWAC). Thermal conductivity coefficient varies from 0.25 to 0.37 W/mK (lower than maximum limit 0.43 W/mK) and compressive strength varies from 19 to 23 MPa (higher than minimum limit 17 MPa). The results indicate that sintering of lignite combustion residues is an efficient method of utilization of carbon containing BA and production of LWA for structural and insulating purposes. Carbon content of BA is a key factor in LWA production. Finally, this research work comprises the first proposed application for utilization of BA in Greece.

  5. Baseline risk assessment of ground water contamination at the inactive uriniferous lignite ashing site near Belfield, North Dakota

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-08-01

    This Baseline Risk Assessment of Ground Water Contamination at the Inactive Uraniferous Lignite Ashing Site Near Belfield, North Dakota, evaluates potential impacts to public health or the environment resulting from ground water contamination at the site where coal containing uranium was burned to produce uranium. The US Department of Energy`s Uranium Mill Tailings Remedial Action (UMTRA) Project is evaluating plans to remedy soil and ground water contamination at the site. Phase I of the UMTRA Project consists of determining the extent of soil contamination. Phase II of the UMTRA Project consists of evaluating ground water contamination. Under Phase II, results of this risk assessment will help determine what remedial actions may be necessary for contaminated ground water at the site. This risk assessment evaluates the potential risks to human health and the environment resulting from exposure to contaminated ground water as it relates to historic processing activities at the site. Potential risk is quantified for constituents introduced from the processing activities, and not for those constituents naturally occurring in water quality in the site vicinity. Background ground water quality has the potential to cause adverse health effects from exposure through drinking. Any risks associated with contaminants attributable to site activities are incremental to these risks from background ground water quality. This incremental risk from site-related contaminants is quantified in this risk assessment. The baseline risk from background water quality is incorporated only into the assessment of potential chemical interactions and the definition of the overall site condition.

  6. Baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Belfield, North Dakota

    International Nuclear Information System (INIS)

    1994-08-01

    This Baseline Risk Assessment of Ground Water Contamination at the Inactive Uraniferous Lignite Ashing Site Near Belfield, North Dakota, evaluates potential impacts to public health or the environment resulting from ground water contamination at the site where coal containing uranium was burned to produce uranium. The US Department of Energy's Uranium Mill Tailings Remedial Action (UMTRA) Project is evaluating plans to remedy soil and ground water contamination at the site. Phase I of the UMTRA Project consists of determining the extent of soil contamination. Phase II of the UMTRA Project consists of evaluating ground water contamination. Under Phase II, results of this risk assessment will help determine what remedial actions may be necessary for contaminated ground water at the site. This risk assessment evaluates the potential risks to human health and the environment resulting from exposure to contaminated ground water as it relates to historic processing activities at the site. Potential risk is quantified for constituents introduced from the processing activities, and not for those constituents naturally occurring in water quality in the site vicinity. Background ground water quality has the potential to cause adverse health effects from exposure through drinking. Any risks associated with contaminants attributable to site activities are incremental to these risks from background ground water quality. This incremental risk from site-related contaminants is quantified in this risk assessment. The baseline risk from background water quality is incorporated only into the assessment of potential chemical interactions and the definition of the overall site condition

  7. Future of lignite resources: a life cycle analysis.

    Science.gov (United States)

    Wang, Qingsong; Liu, Wei; Yuan, Xueliang; Zheng, Xiaoning; Zuo, Jian

    2016-12-01

    Lignite is a low-quality energy source which accounts for 13 % of China's coal reserves. It is imperative to improve the quality of lignite for large-scale utilization. To further explore and analyze the influence of various key processes on the environment and economic costs, a lignite drying and compression technology is evaluated using an integrated approach of life cycle assessment and life cycle costs. Results showed that lignite mining, direct air emissions, and electricity consumption have most significant impacts on the environment. An integrated evaluation of life cycle assessment and life cycle costs showed that the most significant contributor to the environmental impacts and economic costs was the lignite mining process. The impact of transportation and wastewater treatment process on the environment and economic costs was small enough to be ignored. Critical factors were identified for reducing the environmental and economic impacts of lignite drying and compression technology. These findings provide useful inputs for both industrial practice and policy making for exploitation, processing, and utilization of lignite resources.

  8. Preparation and combustion of Yugoslavian lignite-water fuel, Task 7.35. Topical report, July 1991--December 1993

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, C.M.; DeWall, R.A.; Ljubicic, B.R.; Musich, M.A.; Richter, J.J.

    1994-03-01

    Yugoslavia`s interest in lignite-water fuel (LWF) stems from its involvement in an unusual power project at Kovin in northern Serbia. In the early 1980s, Electric Power of Serbia (EPS) proposed constructing a 600-MW power plant that would be fueled by lignite found in deposits along and under the Danube River. Trial underwater mining at Kovin proved that the dredging operation is feasible. The dredging method produces a coal slurry containing 85% to 90% water. Plans included draining the water from the coal, drying it, and then burning it in the pulverized coal plant. In looking for alternative ways to utilize the ``wet coal`` in a more efficient and economical way, a consortium of Yugoslavian companies agreed to assess the conversion of dredged lignite into a LWF using hot-water-drying (HWD) technology. HWD is a high-temperature, nonevaporative drying technique carried out under high pressure in water that permanently alters the structure of low-rank coals. Changes effected by the drying process include irreversible removal of moisture, micropore sealing by tar, and enhancement of heating value by removal of oxygen, thus, enhancement of the slurry ability of the coal with water. Physical cleaning results indicated a 51 wt % reduction in ash content with a 76 wt % yield for the lignite. In addition, physical cleaning produced a cleaned slurry that had a higher attainable solids loading than a raw uncleaned coal slurry. Combustion studies were then performed on the raw and physically cleaned samples with the resulting indicating that both samples were very reactive, making them excellent candidates for HWD. Bench-scale results showed that HWD increased energy densities of the two raw lignite samples by approximately 63% and 81%. An order-of-magnitude cost estimate was conducted to evaluate the HWD and pipeline transport of Kovin LWF to domestic and export European markets. Results are described.

  9. Factors of Reclamation Success at the Lignite Strip-Mined Land in Northern Greece

    Directory of Open Access Journals (Sweden)

    Thomas Panagopoulos

    2013-06-01

    Full Text Available The adverse ecological conditions at the lignite mines of Ptolemaida make the landscape reclamation difficult. The naturally established vegetation and soil properties were studied prior to reclamation. Various forest species were planted to assess the afforestation potential. The natural vegetation was heterogeneous but can be used for the analysis of the site. The soil of the spoil heaps was heterogeneous with unfavourable physicochemical properties. Surface soil temperature was still 24º C higher in bare soil than in soil covered with vegetation. The most successful species of the afforestation trial were Robinia pseudoacacia and Cedrus atlantica. Covering of fly ash spoils with topsoil presented poor results, while sewage sludge gave a favorable amelioration response in areas with high fly ash content. Topsoil from older stands was the suggested method to establish Robinia pseudoacacia. Reclamation success was dependent on appropriate planning; thus, the new landscape had to be designed in harmony with the surrounding landscape before the start of the mining activity.

  10. Assessing the effects of FBC ash treatments of metal-contaminated soils using life history traits and metal bioaccumulation analysis of the earthworm Eisenia andrei

    Energy Technology Data Exchange (ETDEWEB)

    Grumiaux, F.; Demuynck, S.; Schikorski, D.; Lemiere, S.; Lepretre, A. [Universite Lille Nord de France, Villeneuve Dascq (France)

    2010-03-15

    Earthworms (Eisenia andrei) were exposed, in controlled conditions, to metal-contaminated soils previously treated in situ with two types of fluidized bed combustion ashes. Effects on this species were determined by life history traits analysis. Metal immobilizing efficiency of ashes was indicated by metal bioaccumulation. Ashes-treated soils reduced worm mortality compared to the untreated soil. However, these ashes reduced both cocoon hatching success and hatchlings numbers compared to the untreated soil. In addition, sulfo-calcical ashes reduced or delayed worm maturity and lowered cocoon production compared to silico-alumineous ones. Metal immobilizing efficiency of ashes was demonstrated for Zn, Cu and to a lesser extent Pb. Only silico-alumineous ashes reduced Cd bioaccumulation, although Cd was still bioconcentrated. Thus, although ash additions to metal-contaminated soils may help in immobilizing metals, their use might result, depending on the chemical nature of ashes, to severe detrimental effects on earthworm reproduction with possible long term consequences to populations.

  11. The future path of lignite production in the Balkan countries

    International Nuclear Information System (INIS)

    Boussios, E.; Koikouzas, N.K.

    1997-01-01

    The future development of the European Union and Balkan lignite industry is examined in this paper. Lignite in some countries represents for the last decade by far the most important fuel for electricity generation. The economically recoverable lignite reserves of the Balkans (21.36 x 10 9 t) and Greece (4.0 x 10 9 t) are sufficient to meet their energy demand for the next decades (50-100 years). The Balkan countries intended to increase their lignite production, in the near future, as result of the increase of their primary energy demand and their efforts to meet their energy requirements by using domestic resources. Greece also plans to increase lignite production. On the contrary, the remaining of the European Union countries intend to decrease their lignite production. Nevertheless, the countries of Balkan region which are presently in a transition period to the market economy, have to deal with a decrease of people employed in the lignite mining industry. However, Balkan region seems to be the most promising area for the future development of the lignite industry in the enlarged EU, after making the following alterations in the lignite sector: Rehabilitation of the lignite open-pit mines, closure of the most underground mines, privatization of the most prosperous mines, modification of the existing technology, introduction of the 'clean' coal technology, etc. New opportunities for the development and modernization of the lignite industry in Balkan countries arise, after their possible entrance into the European Union, considering also that lignite is one of their most important indigenous energy source. For the necessary modernization of the lignite industry, development of collaborations for the capital and know-how transferring is required. (Author)

  12. Effect of Lignite Fly Ash on the Growth and Reproduction of Earthworm Eisenia fetida

    Directory of Open Access Journals (Sweden)

    S. Sarojini

    2009-01-01

    Full Text Available Fly ash is an amorphous ferroalumino silicate, an important solid waste around thermal power plants. It creates problems leading to environmental degradation due to improper utilization or disposal. However, fly ash is a useful ameliorant that may improve the physical, chemical and biological properties of soils and is a source of readily available plant macro and micronutrients when it is used with biosolids. Supply of nutrients from fly ash with biosolids may enhance their agricultural use. The growth and reproduction of Eisenia fetida was studied during vermicomposting of fly ash with cowdung and pressmud in four different proportions (T1,T2,T3 & T4 and one control i.e., cow dung and pressmud alone. The growth, cocoon and hatchlings production were observed at the interval of 15 days over a period of 60 days. The maximum worm growth and reproduction was observed in bedding material alone. Next to that the T1 was observed as the best mixture for vermiculture.

  13. Sustainable Mining Land Use for Lignite Based Energy Projects

    Science.gov (United States)

    Dudek, Michal; Krysa, Zbigniew

    2017-12-01

    This research aims to discuss complex lignite based energy projects economic viability and its impact on sustainable land use with respect to project risk and uncertainty, economics, optimisation (e.g. Lerchs and Grossmann) and importance of lignite as fuel that may be expressed in situ as deposit of energy. Sensitivity analysis and simulation consist of estimated variable land acquisition costs, geostatistics, 3D deposit block modelling, electricity price considered as project product price, power station efficiency and power station lignite processing unit cost, CO2 allowance costs, mining unit cost and also lignite availability treated as lignite reserves kriging estimation error. Investigated parameters have nonlinear influence on results so that economically viable amount of lignite in optimal pit varies having also nonlinear impact on land area required for mining operation.

  14. Characterisation of lignite as an industrial adsorbent

    Energy Technology Data Exchange (ETDEWEB)

    Ying Qi; Andrew F.A. Hoadley; Alan L. Chaffee; Gil Garnier [Monash University, Clayton, Vic. (Australia). Department of Chemical Engineering

    2011-04-15

    An alternative use of the abundant and inexpensive lignite (also known as brown coal) as an industrial adsorbent has been characterised. The adsorptive properties of two Victorian lignite without any pre-treatment were investigated using the cationic methylene blue dye as a model compound in aqueous solutions. Two commercial activated carbon products were also studied for comparison. The adsorption equilibrium of the four adsorbents was better described by the Langmuir isotherm model than the Freundlich model. The adsorption capacities of the two untreated lignite adsorbents, Loy Yang and Yallourn, calculated using Langmuir isotherms were 286 and 370 mg/g, respectively, higher than a coconut shell-based activated carbon (167 mg/g), but lower than a coal-based activated carbon (435 mg/g). Surface area results suggested that larger micropores and mesopores were important for achieving good methylene blue adsorption by the activated carbons. However, FTIR and cation exchange capacity analyses revealed that, for the lignite, chemical interactions between lignite surface functional groups and methylene blue molecules occurred, thereby augmenting its adsorption capacity. 63 refs., 3 figs., 7 tabs.

  15. Lignite As Contributory Factor to Regional Development of Greece

    OpenAIRE

    Ilias Kordas

    2006-01-01

    Lignite (brown coal) is Greece's most important energy mineral raw material. Lignite exploitation has made a highly significant contribution to the development of energy sector of Greece on past 50 years, and will, according to estimations, continue to supply energy for another 40 years. Greece is very rich in Lignite resources. The two main basins - from where Lignite is extracted by opencast mining - are a) in Western Macedonia (northen Greece) where is generated the 70% of the whole electr...

  16. Influence of Specific Surface of Lignite Fluidal Ashes on Rheological Properties of Sealing Slurries / Wpływ Powierzchni Właściwej Popiołów Fluidalnych z Węgla Brunatnego na Właściwości Reologiczne Zaczynów Uszczelniających

    Science.gov (United States)

    Stryczek, Stanisław; Wiśniowski, Rafał; Gonet, Andrzej; Złotkowski, Albert

    2012-11-01

    New generation fly ashes come from the combustion of coal in fluid-bed furnaces with simultaneous sulphur-removal from gases at ca. 850°C. Accordingly, all produced ashes basically differ in their physicochemical properties from the traditional silica ones. The aim of the laboratory analyses was determining the influence of specific surface and granular composition of fluidal ash on rheological properties of slurries used for sealing up the ground and rock mass media with hole injection methods, geoengineering works and cementing casing pipes in deep boreholes. Fluidal ash from the combustion of lignite contain active Puzzolan appearing in the form of dehydrated clayey minerals and active components activating the process of hydration ashes, i.e. CaO, anhydrite II and CaCO3. The ashes have a weak point, i.e. their high water diment, which the desired rheological properties related with the range of their propagation in the rock mass cannot not be acquired for injection works in the traditional sealing slurries technology. Increasing the water-to-mixture ratio should eliminate this feature of fluidal ashes. Laboratory analyses were performed for slurries based on metallurgical cement CEM III/A 32,5 having water-to-mixture ratios: 0.5; 0.6 ; 0.7 and 0.8; the fluidal ash concentration in the slurries was 30 wt.% (with respect to the mass of dry cement). Basing on the obtained results there were determined optimum recipes of sealing slurries in view of their rheological parameters which could be applied both in drilling technologies (cementing casing pipes, closing of boreholes, plugging) and in geoengineering works related with sealing up and reinforcing ground and rock mass media.

  17. Mercury capture by selected Bulgarian fly ashes: Influence of coal rank and fly ash carbon pore structure on capture efficiency

    Science.gov (United States)

    Kostova, I.J.; Hower, J.C.; Mastalerz, Maria; Vassilev, S.V.

    2011-01-01

    Mercury capture by fly ash C was investigated at five lignite- and subbituminous-coal-burning Bulgarian power plants (Republika, Bobov Dol, Maritza East 2, Maritza East 3, and Sliven). Although the C content of the ashes is low, never exceeding 1.6%, the Hg capture on a unit C basis demonstrates that the low-rank-coal-derived fly ash carbons are more efficient in capturing Hg than fly ash carbons from bituminous-fired power plants. While some low-C and low-Hg fly ashes do not reveal any trends of Hg versus C, the 2nd and, in particular, the 3rd electrostatic precipitator (ESP) rows at the Republika power plant do have sufficient fly ash C range and experience flue gas sufficiently cool to capture measurable amounts of Hg. The Republika 3rd ESP row exhibits an increase in Hg with increasing C, as observed in other power plants, for example, in Kentucky power plants burning Appalachian-sourced bituminous coals. Mercury/C decreases with an increase in fly ash C, suggesting that some of the C is isolated from the flue gas stream and does not contribute to Hg capture. Mercury capture increases with an increase in Brunauer-Emmett-Teller (BET) surface area and micropore surface area. The differences in Hg capture between the Bulgarian plants burning low-rank coal and high volatile bituminous-fed Kentucky power plants suggests that the variations in C forms resulting from the combustion of the different ranks also influence the efficiency of Hg capture. ?? 2010 Elsevier Ltd.

  18. Mercury capture by selected Bulgarian fly ashes: Influence of coal rank and fly ash carbon pore structure on capture efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Kostova, I.J.; Hower, J.C.; Mastalerz, M.; Vassilev, S.V. [University of Kentucky, Lexington, KY (United States). Center of Applied Energy Research

    2011-01-15

    Mercury capture by fly ash C was investigated at five lignite- and subbituminous-coal-burning Bulgarian power plants (Republika, Bobov Dol, Maritza East 2, Maritza East 3, and Sliven). Although the C content of the ashes is low, never exceeding 1.6%, the Hg capture on a unit C basis demonstrates that the low-rank-coal-derived fly ash carbons are more efficient in capturing Hg than fly ash carbons from bituminous-fired power plants. While some low-C and low-Hg fly ashes do not reveal any trends of Hg versus C, the 2nd and, in particular, the 3rd electrostatic precipitator (ESP) rows at the Republika power plant do have sufficient fly ash C range and experience flue gas sufficiently cool to capture measurable amounts of Hg. The Republika 3rd ESP row exhibits an increase in Hg with increasing C, as observed in other power plants, for example, in Kentucky power plants burning Appalachian-sourced bituminous coals. Mercury/C decreases with an increase in fly ash C, suggesting that some of the C is isolated from the flue gas stream and does not contribute to Hg capture. Mercury capture increases with an increase in Brunauer-Emmett-Teller (BET) surface area and micropore surface area. The differences in Hg capture between the Bulgarian plants burning low-rank coal and high volatile bituminous-fed Kentucky power plants suggests that the variations in C forms resulting from the combustion of the different ranks also influence the efficiency of Hg capture.

  19. Degradation/solubilization of Chinese lignite by Penicillium sp. P6

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, H.L.; Yang, J.S.; Wang, F.Q.; Chen, W.X. [China Agricultural University, Beijing (China). Key Laboratory of Agro-Microbial Resource and Application, Ministry of Agrio, College of Biological Science

    2006-01-15

    Penicillium sp. P6, isolated from coal mine soil at the Qiantong colliery Liaoning Province, Northeast China, can degrade Chinese lignite in 36 h on a plate colony and in 48 h using a 4-day cultured cell-free filtrate. Results of elemental analysis and IR spectrometry indicated that solubilized products exhibited some alterations in comparison to the original lignite. The amount of fulvic acid extracted from the biodegraded lignite was high, and the molecular distribution of the humic acids from biodegraded lignite changed distinctively in comparison to which extracted from the control lignite, possibly due to the depolymerization associated with fungal biodegradation.

  20. Recovery of uranium from lignites

    International Nuclear Information System (INIS)

    Hurst, F.J.

    1980-01-01

    Uranium in raw lignite is associated with the organic matter and is readily soluble in acid (and carbonate) solutions. However, beneficiation techniques were not successful for concentrating the uranium or removing part of the reagent-consuming materials. Once the lignite was heated, the uranium became much less soluble in both acid and carbonate solutions, and complete removal of carbon was required to convert it back to a soluble form. Proper burning improves acid-leaching efficiency; that is, it reduces the reagent consumption and concentrates the uranium, thereby reducing plant size for comparable uranium throughput, and it eliminates organic fouling of leach liquors. Restrictions are necessary during burning to prevent the uranium from becoming refractory. The most encouraging results were obtained by flash-burning lignite at 1200 to 1300 0 C and utilizing the released SO 2 to supplement the acid requirement. The major acid consumers were aluminum and iron

  1. Production of low ash coal by thermal extraction with N-methyl-2-pyrrolidinone

    Energy Technology Data Exchange (ETDEWEB)

    Do Kim, S.; Woo, K.J.; Jeong, S.K.; Rhim, Y.J.; Lee, S.H. [Korean Institute for Energy Research, Taejon (Republic of Korea). Clean Coal Technological Research Center

    2008-07-15

    Present study was conducted for the purpose of producing low ash coal from LRC (low rank coals) such as lignite and sub-bituminous coal through thermal extraction using polar solvent. Extraction from bituminous coal was also investigated for comparison. NMP as a polar solvent was used. The ratio of coal to solvent was adjusted as 1:10. Experimental conditions were established which include the extraction temperature of 200-430{sup o}C, initial applied pressure of 1-20 bar and extraction time of 0.5-2 hr were used. Extraction yield and ash content of extracted and residual coal were measured. The extraction yield increased with the increase of extraction temperature, and the ash content of extracted coal decreased below 0.4% at 400{sup o}C from the raw coal samples that have the ash contents of 4-6%. According to the analysis of experiments results, fixed carbon and calorific value increased, and H/C and O/C decreased.

  2. Biodegradation of photo-oxidized lignite and characterization of the products

    Science.gov (United States)

    Li, Jiantao; Liu, Xiangrong; Yue, Zilin; Zhang, Yaowen

    2018-01-01

    Biodegradation of photo-oxidized Inner Mongolia lignite by pseudomonas aeruginosa was studied and the degradation percentage reached 56.27%, while the corresponding degradation percentage of the strain degrading raw Inner Mongolia lignite is only 23.16%. The degradation products were characterized. Proximate and ultimate analyses show that the higher oxygen content increased by photo-oxidation pretreatment maybe promoted the degradation process. Ultraviolet spectroscopy (UV) analysis of the liquid product reveals that it contains unsaturated structures and aromatic rings are the main structure units. Gas chromatography-mass spectrometry (GC-MS) analysis indicates that the main components of the ethyl acetate extracts are low molecular weight organic compounds, such as ketones, acids, hydrocarbons, esters and alcohols. Infrared spectroscopy (IR) analysis of raw lignite, photo-oxidized lignite and residual lignite demonstrates that the absorption peaks of functional groups in residual lignite disappeared or weakened obviously. Scanning electron microscopy (SEM) analysis manifests that small holes appear in photo-oxidized lignite surface, which may be promote the degradation process and this is only from the physical morphology aspects, so it can be inferred from the tests and analyses results that the more important reason of the high degradation percentage is mostly that the photo-oxidation pretreatment changes the chemical structures of lignite.

  3. Speciation of selected trace and major elements in lignite Used in "Nikola Tesla A" power plant (Obrenovac, Serbia

    Directory of Open Access Journals (Sweden)

    ALEKSANDAR POPOVIC

    2005-12-01

    Full Text Available Four samples of milled lignite used in the “Nikola Tesla A” power plant, located in Obrenovac near Belgrade, were subjected to a five-step sequential extraction, comprising of the following phases: distilled water, 1 M ammonium acetate, 0.2 M ammonium oxalate / 0.2 M oxalic acid, acidic solution of H2O2 and a 6 M solution of HCl. The concentrations of the different elements obtained in the extractions were statistically analysed. The majority of the examined elements were found to be most probably associated with inorganic fractions of lignite, only aluminum, silicon, chromium and arsenic have a larger extractable organic/sulfide fraction than an extractable inorganic fraction. Alumosilicates of magnesium (carriers of arsenic, zinc, lead, copper and chromium, silicates of potassium (scavengers of lead and nickel, mixed aluminates of iron and magnesium (carriers of arsenic, zinc, copper and chromium and compounds of iron that do not contain aluminum and magnesium (scavengers of manganese were dissolved in the fifth phase of the sequential extraction. Copper is a substrate of alumosilicates of potassium and magnesium, while zinc and chromium are substrates of compounds of iron leached in the third phase of the sequential extraction. Interphase correlation revealed that the adsorbed and ion-exchangeable fractions of most of the examined elements do not exhibit preferential binding to the components of the inorganic matrix of lignite ash.

  4. Effect of biomass on burnouts of Turkish lignites during co-firing

    Energy Technology Data Exchange (ETDEWEB)

    Haykiri-Acma, H.; Yaman, S. [Istanbul Technical Univ., Chemical and Metallurgical Engineering Faculty, Chemical Engineering Dept., 34469 Maslak, Istanbul (Turkey)

    2009-09-15

    Co-firing of some low quality Turkish lignites with woody shells of sunflower seed was investigated via non-isothermal thermogravimetric analysis method. For this purpose, Yozgat-Sorgun, Erzurum-Askale, Tuncbilek, Gediz, and Afsin-Elbistan lignites were selected, and burnouts of these lignites were compared with those of their blends. Biomass was blended as much as 10 and 20 wt.% of the lignites, and heating was performed up to 900 C at a heating rate of 40 C/min under dry air flow of 40 mL/min. This study revealed that the same biomass species may have different influences on the burnout yields of the lignites. Burnouts of Erzurum-Askale lignite increased at any temperature with the increasing ratio of biomass in the blend, whereas burnout yields of other lignites decreased to some extent. Nevertheless, the blends of Turkish lignites with sunflower seed shell did not behave in very different way, and it can be concluded that they are compatible in terms of burnouts for co-combustion in a combustion system. Although the presence of biomass in the lignite blends caused to some decreases in the final burnouts, the carbon dioxide neutral nature of biomass should be taken into account, and co-combustion is preferable for waste-to-energy-management. (author)

  5. Effect of biomass on burnouts of Turkish lignites during co-firing

    International Nuclear Information System (INIS)

    Haykiri-Acma, H.; Yaman, S.

    2009-01-01

    Co-firing of some low quality Turkish lignites with woody shells of sunflower seed was investigated via non-isothermal thermogravimetric analysis method. For this purpose, Yozgat-Sorgun, Erzurum-Askale, Tuncbilek, Gediz, and Afsin-Elbistan lignites were selected, and burnouts of these lignites were compared with those of their blends. Biomass was blended as much as 10 and 20 wt.% of the lignites, and heating was performed up to 900 deg. C at a heating rate of 40 deg. C/min under dry air flow of 40 mL/min. This study revealed that the same biomass species may have different influences on the burnout yields of the lignites. Burnouts of Erzurum-Askale lignite increased at any temperature with the increasing ratio of biomass in the blend, whereas burnout yields of other lignites decreased to some extent. Nevertheless, the blends of Turkish lignites with sunflower seed shell did not behave in very different way, and it can be concluded that they are compatible in terms of burnouts for co-combustion in a combustion system. Although the presence of biomass in the lignite blends caused to some decreases in the final burnouts, the carbon dioxide neutral nature of biomass should be taken into account, and co-combustion is preferable for waste-to-energy-management.

  6. Bio-solubilization of Chinese lignite II: extra-cellular protein analysis

    Energy Technology Data Exchange (ETDEWEB)

    Tao, Xiu-xiang; Pan, Lan-ying; Shi, Kai-yi; Chen-hui; Yin, Su-dong; Luo, Zhen-fu [China University of Mining & Technology, Xuzhou (China). School of Chemical Engineering and Technology

    2009-05-15

    A white rot fungus strain, Trichoderma sp. AH, was isolated from rotten wood in Fushun and used to study the mechanism of lignite bio-solubilization. The results showed that nitric acid pretreated Fushun lignite was solubilized by T. sp. AH and that extracellular proteins from T. sp. AH were correlated with the lignite bio-solubilization results. In the presence of Fushun lignite the extracellular protein concentration from T. sp. AH was 4.5 g/L while the concentration was 3 g/L in the absence of Fushun lignite. Sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) of the extracelular proteins detected at least four new protein bands after the T. sp. AH had solubilized the lignite. Enzyme color reactions showed that extracelular proteins from T. sp. AH mainly consisted of phenol-oxidases, but that lignin decomposition enzymes such as laccase, peroxidase and manganese peroxidases were not present. 9 refs., 8 figs.

  7. Solubilization of Australian lignites by fungi and other microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Catcheside, D.E.A.; Mallett, K.J. (Flinders University, Bedford Park, SA (Australia). School of Biological Sciences)

    Lignites (brown coals) from the Latrobe Valley in Victoria are solubilized by {ital Coriolus versicolor}, {ital Phanerochaete chrysosporium}, and five other species known to be active on Leonardite and various acid-treated North America lignites. Run-of-mine coal from Morwell and Loy Yang is refractory but is soluble after pretreatment with acid. A weathered deposit at Loy Yang, like Leonardite, is susceptible to biosolubilization without pretreatment. The white rot fungi {ital Ganoderma applanatum}, {ital Perenniporia tephropora} ({ital Fomes lividus}), {ital Pleurotus ostreatus}, {ital Pycnoporus cinnabarinus}, {ital Rigidoporus ulmarius}, and {ital Xylaria hypoxylon} were found to be capable of solubilizing lignite. In contrast, brown rot fungi were weakly active or inactive under the same test conditions. Lignite-degrading fungi, actinomycetes, and other bacteria, including some active on untreated run-of-mine coal, were isolated from natural lignite exposures and mining sites. 15 refs., 5 tabs.

  8. Bioprocessing of lignite coals using reductive microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, D.L.

    1992-03-29

    In order to convert lignite coals into liquid fuels, gases or chemical feedstock, the macromolecular structure of the coal must be broken down into low molecular weight fractions prior to further modification. Our research focused on this aspect of coal bioprocessing. We isolated, characterized and studied the lignite coal-depolymerizing organisms Streptomyces viridosporus T7A, Pseudomonas sp. DLC-62, unidentified bacterial strain DLC-BB2 and Gram-positive Bacillus megaterium strain DLC-21. In this research we showed that these bacteria are able to solubilize and depolymerize lignite coals using a combination of biological mechanisms including the excretion of coal solublizing basic chemical metabolites and extracellular coal depolymerizing enzymes.

  9. A comparison of improved power plant technologies on lignite with (PFBC) and (IGCC) cycles

    International Nuclear Information System (INIS)

    Cherepnalkovski, Ilija

    1997-01-01

    Technologies and process diagrams descriptions for PFBC (Pressurised Fluidized Bed Combustion) and IGCC (Integrated Gasification Combined Cycle) are presented as for improved cycles with modern clean coal technologies, the most popular currently. A special attention is paid to the possibilities for Macedonian lignites use on the power plants with PFBC and IGCC cycles. The comparison of the above mention technologies has been done particularly on the desulfurization, NO x reduction, ash elimination and its use in the building and construction industries. A comparison between the power plants with PFBC and IGCC cycles is made by the following criteria: cycle efficiency, desulfurization and nitrogen oxides reduction, power plant complexity and their cost, as well as plant reliability. (Author)

  10. Cleaning of flue gases from lignite-fired power plants by electron beam technology

    International Nuclear Information System (INIS)

    Ruskov, T.

    1998-01-01

    An essential part of the electricity production in Bulgaria depends on the combustion of lignite with high humidity and high sulphur content. As a result of burning, toxic gases as sulphur dioxide (SO 2 ) and nitrous oxides (NO x ) are emitted in the atmosphere. Both S0 2 and NO x in flue gases could be removed simultaneously by the Electron Beam (EB) process. Beforehand cleaned from fly ash, the flue gas is cooled by injection of water and ammonia is added. By irradiation with high energy electrons, S0 2 and NO x are converted into aerosols of ammonium sulphate and ammonium nitrate. The byproduct is collected by an electrostatic precipitator and is used for the production of fertilisers

  11. Biosolubilization of raw and gamma irradiated lignite by trichoderma asperellum

    International Nuclear Information System (INIS)

    Sugoro, I.; Astuti, D.I.; Aditiawati, P.; Sasongko, D.

    2012-01-01

    Biosolubilization is a promising technology for converting solid coal to liquid oil by addition of microorganism. Aim of this research is to compare between gamma irradiated lignite (10 kGy) with raw lignite in biosolubilization by selected fungi Trichoderma asperellum. Treatments were A (MSS + gamma irradiated lignite 5% + T. asperellum) and B (MSS + raw lignite 5% + T. asperellum) with sub-merged culture. There were two parameters observed i.e. biosolubilization product based on absorbance value at λ 250nm and λ 450nm and metal analysis by neutron activation analysis (NAA). The highest biosolubilization will be analyzed by FTIR and GCMS. The results showed that biosolubilization of raw lignite (B) was higher than sterilized lignite (A) based on absorbance value at λ 250nm and λ 450nm . The metal of lignite was decreased after incubation. FTIR analysis showed that both of treatment had similar spectra on biosolubilization products. GCMS analysis showed that both of treatment had different number of hydrocarbon, i.e. C 6 - C 35 (A) and C 10 - C 35 (B) and dominated by aromatic acids, aliphatic and phenylethers. Both of treatment product had the potency as oil substituted but its recommended to deoxygenate for higher quality. (author)

  12. The clean coal technologies for lignitic coal power generation in Pakistan

    International Nuclear Information System (INIS)

    Mir, S.; Raza, Z.; Aziz-ur-Rehman, A.

    1995-01-01

    Pakistan contains huge reserves of lignitic coals. These are high sulphur, high ash coals. In spite of this unfortunate situation, the heavy demand for energy production, requires the development utilization of these indigenous coal reserves to enhance energy production. The central of the environmental pollution caused by the combustion of these coals has been a major hindrance in their utilization. Recently a substantial reduction in coal combustion emissions have been achieved through the development of clean coal technologies. Pakistan through the transfer and adaptation of the advanced clean coal technologies can utilize incurring the high sulphur coals for energy production without incurring the environmental effects that the developed countries have experienced in the past. The author discusses the recently developed clean coal utilization technologies, their applications economies and feasibility of utilization with specific reference to Pakistan''s coal. (author)

  13. Concentrations and source apportionment of PM10 and associated elemental and ionic species in a lignite-burning power generation area of southern Greece.

    Science.gov (United States)

    Argyropoulos, G; Grigoratos, Th; Voutsinas, M; Samara, C

    2013-10-01

    Ambient concentrations of PM10 and associated elemental and ionic species were measured over the cold and the warm months of 2010 at an urban and two rural sites located in the lignite-fired power generation area of Megalopolis in Peloponnese, southern Greece. The PM10 concentrations at the urban site (44.2 ± 33.6 μg m(-3)) were significantly higher than those at the rural sites (23.7 ± 20.4 and 22.7 ± 26.9 μg m(-3)). Source apportionment of PM10 and associated components was accomplished by an advanced computational procedure, the robotic chemical mass balance model (RCMB), using chemical profiles for a variety of local fugitive dust sources (power plant fly ash, flue gas desulfurization wet ash, feeding lignite, infertile material from the opencast mines, paved and unpaved road dusts, soil), which were resuspended and sampled through a PM10 inlet onto filters and then chemically analyzed, as well as of other common sources such as vehicular traffic, residential oil combustion, biomass burning, uncontrolled waste burning, marine aerosol, and secondary aerosol formation. Geological dusts (road/soil dust) were found to be major PM10 contributors in both the cold and warm periods of the year, with average annual contribution of 32.6 % at the urban site vs. 22.0 and 29.0 % at the rural sites. Secondary aerosol also appeared to be a significant source, contributing 22.1 % at the urban site in comparison to 30.6 and 28.7 % at the rural sites. At all sites, the contribution of biomass burning was most significant in winter (28.2 % at the urban site vs. 14.6 and 24.6 % at the rural sites), whereas vehicular exhaust contribution appeared to be important mostly in the summer (21.9 % at the urban site vs. 11.5 and 10.5 % at the rural sites). The highest contribution of fly ash (33.2 %) was found at the rural site located to the north of the power plants during wintertime, when winds are favorable. In the warm period, the highest contribution of fly ash was found at the

  14. Oxidative desulfurization of Cayirhan lignites by permanganate solution

    Energy Technology Data Exchange (ETDEWEB)

    Guru, M.; Tuzun, F.N.; Murathan, A.S.; Asan, A.; Kiyak, T. [Gazi University, Ankara (Turkey). Dept. for Chemical Engineering

    2008-07-01

    Unless important developments record new and renewable energy sources, the role of fossil fuels as an energy resource goes on. It is possible to detect sulfur, heavy metals, and tracer elements such as arsenic and selenium by decreasing calorific value of coals. Sulfur oxides, which are the main pollutants in atmosphere, are irritative to humans and plants, and erosion occurs on buildings. Although there are high lignite reservoirs, high sulfur content limits the efficient use of them. In this research, it is aimed to convert combustible sulfur in coal to non-combustible sulfur form in the ash by oxidizing it with permanganate solution. During this research, the effect of two different parameters of potassium permanganate concentration, processing time, and mean particle size were investigated at constant room temperature and shaking rate. The conversion of combustible sulfur to non-combustible sulfur form was achieved optimally with 0.14 M potassium permanganate solution, 0.1 mm mean particle size at 16 h of treatment time, and the combustible sulfur amount was decreased by 46.37% compared to undoped conditions.

  15. Lignite mining and electricity generation in Poland: The current state and future prospects

    International Nuclear Information System (INIS)

    Widera, Marek; Kasztelewicz, Zbigniew; Ptak, Miranda

    2016-01-01

    This opinion paper presents the current state and future scenarios of Polish lignite mining. For many years, over 1/3 of domestic electricity, that is about 53–55 TWh, has been generated by lignite-fired power plants. Currently, with 63–66 million tons of extraction, Poland is the fourth lignite producer worldwide and the second in the European Union. There are three possible scenarios for the development of lignite mining in Poland by 2050. Unfortunately, despite the huge lignite resources, amounting to more than 23.5 billion tons, and great potential of the mining industry, the future of Polish lignite mining does not look optimistic from the economic point of view. This is associated with social and environmental problems, including the European Union's climate and energy policy. However, this may change in the event of a global economic crisis and unstable geopolitical conditions. Therefore, a new energy doctrine for Poland at least by 2050 is urgently needed. - Highlights: •Poland is one of the leaders in lignite production in the European Union. •Energy policy in Poland assumes a key role of lignite in energy mix. •Almost one-third of Polish electricity is currently generated from lignite. •For Polish lignite mining exist pessimistic, realistic and optimistic scenarios. •Extraction of lignite in Poland will gradually decrease in the coming decades.

  16. Speciation of selected trace and major elements in lignite used in 'Nikola Tesla A' power plant (Obrenovac, Serbia)

    Energy Technology Data Exchange (ETDEWEB)

    Aleksandar Popovic; Dragana Djordjevic [University of Belgrade, Belgrade (Serbia and Montenegro). Department of Chemistry

    2005-07-01

    Four samples of milled lignite used in the 'Nikola Tesla A' power plant, located in Obrenovac near Belgrade, were subjected to a five-step sequential extraction, comprising of the following phases: distilled water, 1 M ammonium acetate, 0.2 M ammonium oxalate/0.2 M oxalic acid, acidic solution of H{sub 2}O{sub 2} and a 6 M solution of HCl. The concentrations of the different elements obtained in the extractions were statistically analysed. The majority of the examined elements were found to be most probably associated with inorganic fractions of lignite, only aluminum, silicon, chromium and arsenic have a larger extractable organic/sulfide fraction than an extractable inorganic fraction. Alumosilicates of magnesium (carriers of arsenic, zinc, lead, copper and chromium), silicates of potassium (scavengers of lead and nickel), mixed aluminates of iron and magnesium (carriers of arsenic, zinc, copper and chromium) and compounds of iron that do not contain aluminum and magnesium (scavengers of manganese) were dissolved in the fifth phase of the sequential extraction. Copper is a substrate of alumosilicates of potassium and magnesium, while zinc and chromium are substrates of compounds of iron leached in the third phase of the sequential extraction. Interphase correlation revealed that the adsorbed and ion-exchangeable fractions of most of the examined elements do not exhibit preferential binding to the components of the inorganic matrix of lignite ash.

  17. Overview of Neyveli lignite complex

    Energy Technology Data Exchange (ETDEWEB)

    1984-09-01

    The growth and development of the Neyveli lignite complex in Tamil Nadu, India are discussed. A second lignite mine is being developed together with a second thermal power station and erection of transmission lines between Neyveli-Salem and Neyveli-Red Hills is under way. The contribution of power to Tamil Nadu has grown into an extremely valuable asset; exports have risen by 71% in the four years leading up to 1984 and company turn-over has increased 164% over the same period. Performance during 1983-84 is analysed in terms of production figures, productivity and capacity utilisation.

  18. Experience in the radiometric on-line determination of the ash content of raw lignite at the Hagenwerder power station

    International Nuclear Information System (INIS)

    Koerner, G.; Leonhardt, J.; Thuemmel, H.W.; Fritzsche, D.

    1986-01-01

    For power station feed control an ash monitoring system has been working for one year. It comprises a by-pass sampling system including the scatter-transmission ash gauge KRAS-1 (total error 3.8 weight percentage ash on dry basis) which is used for calibrating the non-contact on-stream computer-controlled ash gauge KRAS-2 based on the 2-energy transmission method (total error 4.5 weight percentage ash on dry basis). The economic benefit is estimated to 1.4 million Mark per year. (author)

  19. The behaviour of ashes and heavy metals during the co-combustion of sewage sludges in a fluidised bed

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, M.H.; Abelha, P.; Lapa, N.; Oliveira, J.S.; Cabrita, I.; Gulyurtlu, I. [INETI, Lisbon (Portugal)

    2003-07-01

    Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC with the aim of characterizating the ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials.

  20. The behaviour of ashes and heavy metals during the co-combustion of sewage sludges in a fluidised bed.

    Science.gov (United States)

    Helena Lopes, M; Abelha, P; Lapa, N; Oliveira, J S; Cabrita, I; Gulyurtlu, I

    2003-01-01

    Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC aiming at the characterization of ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges, suggesting that there could be opportunities for their further use. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials.

  1. The behaviour of ashes and heavy metals during the co-combustion of sewage sludges in a fluidised bed

    International Nuclear Information System (INIS)

    Helena Lopes, M.; Abelha, P.; Lapa, N.; Oliveira, J.S.; Cabrita, I.; Gulyurtlu, I.

    2003-01-01

    Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC aiming at the characterization of ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges, suggesting that there could be opportunities for their further use. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials

  2. Sustainable lignite mining and utilization. Developments in the Rhenish lignite-mining area; Nachhaltige Braunkohlegewinnung und -nutzung. Entwicklung im Rheinischen Revier

    Energy Technology Data Exchange (ETDEWEB)

    Gaertner, Dieter [RWE Power AG, Bergheim (Germany). Sparte Tagebaue

    2012-09-15

    Lignite is an essential module in the Rhenish mining area's economic power. Mini ng in a densely populated region like the Rhineland calls for keeping an eye equ ally on people, the environment and industry now and in the future. By considering all concerns and ensuring transparency in our approach to people, we have succeeded in obtaining public acceptance also for large-scale projects in an environment that is not always easy in Germany. RWE Power plans to use lignite in powe r generation and in upgrading operations for many decades to come, so that the company is systematically implementing the power-plant renewal programme with is planning for BoAplus as highly efficient next-generation lignite-based power plants. Research on CO{sub 2} utilization, flexibilization, energy storage and alternative uses of lignite are as much features of RWE Power's future-proof alignment in the Rhenish mining area as are further innovations in the opencast mines. Core aspects here include further automation in the deployment of main mine equipment, closely dovetailed with innovations in other operating units. Parallel restructuring of the operating units and the Lignite Approvals area are underpinning these measures. Innovations and their translation into technical progress will ensure the success of a measured energy turnaround both in Germany and throughout Europe. However, this requires dependable political conditions, so that an engineering spirit can go on being transformed into entrepreneurial action. (orig.)

  3. Sustainable lignite mining and utilization. Developments in the Rhenish lignite-mining area; Nachhaltige Braunkohlegewinnung und -nutzung. Entwicklung im Rheinischen Revier

    Energy Technology Data Exchange (ETDEWEB)

    Gaertner, Dieter [RWE Power AG, Bergheim (Germany). Opencast Mines Div.

    2012-03-15

    Lignite is an essential module in the Rhenish mining area's economic power. Mining in a densely populated region like the Rhineland calls for keeping an eye equally on people, the environment and industry now and in the future. By considering all concerns and ensuring transparency in our approach to people, we have succeeded in obtaining public acceptance also for large-scale projects in an environment that is not always easy in Germany. RWE Power plans to use lignite in power generation and in upgrading operations for many decades to come, so that the company is systematically implementing the power-plant renewal programme with is planning for BoAplus as highly efficient next-generation lignite-based power plants. Research on CO{sub 2} utilization, flexibilization, energy storage and alternative uses of lignite are as much features of RWE Power's future-proof alignment in the Rhenish mining area as are further innovations in the opencast mines. Core aspects here include further automation in the deployment of main mine equipment, closely dovetailed with innovations in other operating units. Parallel restructuring of the operating units and the Lignite Approvals area are underpinning these measures. Innovations and their translation into technical progress will ensure the success of a measured energy turnaround both in Germany and throughout Europe. However, this requires dependable political conditions, so that an engineering spirit can go on being transformed into entrepreneurial action. (orig.)

  4. Microstructure and properties of lignite tar and pitch. Part II

    Energy Technology Data Exchange (ETDEWEB)

    Walther, H

    1954-01-01

    Photomicrographs reveal the presence of crystalline wax which affects the working properties in lignite tars and pitch. The crystals are large needles after slow cooling and small after rapid cooling. The crystals are paraffinic in character. All samples were nonhomogeneous. Thus the properties of lignite tar and pitch are varied by the source of the lignite and history of the specimen, neither softening point nor dropping point seems to satisfactorily characterize these tars. The samples exhibit thixotropic behavior characteristic of a structural viscosity and show hysteresis loops on varying the working rate. The variations have hindered use of lignite tars and pitches except where solubility in a solvent such as coal tar oil can be used to advantage.

  5. Lignite mining in India - thirty years of rich experience

    Energy Technology Data Exchange (ETDEWEB)

    Tandon, G L

    1984-11-01

    Exploration of the huge deposits of lignite at Neyveli in Tamil Nadu commenced in 1961 by the opencast method by deploying continuously operating machinery such as bucket-wheel excavators, spreaders and high-speed belt conveyor systems. Adoption of this mining technology to suit the peculiar site conditions at Neyveli has led to many modifications in the equipment and has enriched the experience of the Neyveli Lignite Corporation. This has also made it possible for NLC to formulate schemes for exploration and exploitation of lignite deposits occurring elsewhere in the country.

  6. Lignite mining in India - thirty years of rich experience

    Energy Technology Data Exchange (ETDEWEB)

    Tandon, G L

    1984-11-01

    Exploitation of the huge deposits of lignite at Neyveli in Tamil Nadu commenced in 1961 by opencast method by deploying continuously operating machinery such as bucket-wheel excavators, headers and high speed belt conveyor systems. Adoption of this mining technology to suit the peculiar site conditions at Neyveli has led to many modifications in the equipment and has enriched the experience of the Neyveli Lignite Corporation. This has also made it possible for NLC to formulate schemes for exploration and exploitation of lignite deposits occurring elsewhere in the country.

  7. Lignite industry in Greece within a world context: Mining, energy supply and environment

    International Nuclear Information System (INIS)

    Kavouridis, Konstantinos

    2008-01-01

    Today coal covers 38% of global production and roughly 30% of the EU-25 power output. In 2005 domestic lignite with a share of 60.5% in power generation and accounting about 30% of primary energy consumption is currently the most important indigenous fuel of Greece. Greece, mining 70 Mt annually, is the second lignite producer in the EU and fourth in the world. Approximately 97% of the lignite used to supply the existing lignite-fired power plants of Greece is mined by Public Power Corporation S.A. (PPC). Lignite as the base load fuel gives a competitive strength in PPC's and Greece's fuel mix. Due to lignite consumer prices in Greece are significantly below those in other comparable markets in EU-15. Extraction of lignite has a very long tradition. Significant achievements and large experience which has been gained during many years of mining operations place Greek lignite-mining industry in the leading position in Europe. The paper presents current state of Greek lignite industry, including operating mines, volume of production and other important production indicators as well as improvements in labor productivity and good results in industrial safety. The future of coal and specifically of Greek lignite will be crucially determined by environmentally compatible, i.e. low-CO 2 generation of electricity. Investment in modernization and renewal of the power plant fleet are the key to securing electricity supply and progress in preventing climate change

  8. Low-temperature carbonization plant for lignite

    Energy Technology Data Exchange (ETDEWEB)

    Shiotsuki, Y

    1949-01-01

    The design and operational data of a low-temperature carbonization plant for Japanese lignite are described. The retort had a vertical cylinder with a capacity of about 10 tons per day. By continuous operation, in which a part of the gas produced was circulated and burned in the lignite zone, about 40 percent semicoke and 3 to 4 percent tar were obtained. From the tar the following products were separated: Low-temperature carbonization cresol, 18.3; motor fuel, 1.00; solvent, 9.97; cresol for medical uses, 11.85; and creosote oil, 32 percent.

  9. The structure and pyrolysis product distribution of lignite from different sedimentary environment

    International Nuclear Information System (INIS)

    Liu, Peng; Zhang, Dexiang; Wang, Lanlan; Zhou, Yang; Pan, Tieying; Lu, Xilan

    2016-01-01

    Highlights: • Carbon structure of three lignites was measured by solid "1"3C NMR. • Effect of carbon structure on pyrolysis product distribution was studied. • Tar yield is influenced by aliphatic carbon and oxygen functional group. • C1–C4 content of pyrolysis gas is related to CH_2/CH_3 ratio. - Abstract: Low-temperature pyrolysis is an economically efficient method for lignite to obtain coal tar and improve its combustion calorific value. The research on the distribution of pyrolysis product (especially coal tar yield) plays an important role in energy application and economic development in the now and future. Pyrolysis test was carried out in a tube reactor at 873 K for 15 min. The structure of the lignite was measured by solid "1"3C nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR). The thermal analysis was analyzed by thermo-gravimetric (TG) analyzer. The results show that the pyrolysis product distribution is related to the breakage of branch structures of aromatic ring in lignites from different sedimentary environment. The gas yield and composition are related to the decomposition of carbonyl group and the breakage of aliphatic carbon. The tar yield derived from lignite pyrolysis follows the order: Xianfeng lignite (XF, 13.67 wt.%) > Xiaolongtan lignite (XLT, 7.97 wt.%) > Inner Mongolia lignite (IM, 6.30 wt.%), which is mainly influenced by the aliphatic carbon contents, the CH_2/CH_3 ratio and the oxygen functional groups in lignite. The pyrolysis water yield depends on the decomposition of oxygen functional groups. IM has the highest content of oxygen-linked carbon so that the pyrolysis water yield derived from IM is the highest (9.20 wt.%), and is far more than that from the other two lignites.

  10. Role of Neyveli lignite in the energy map of India

    Energy Technology Data Exchange (ETDEWEB)

    Srinivasaraghavan, S

    1984-08-01

    For more than two decades, about 35% of the energy demand of Tamil Nadu, a region of southern India, has been provided by Neyveli Lignite Corporation (NLC). NLC was founded as a company by the Indian government in 1956 and it comprises a lignite mine, a thermal power station, a briquetting and carbonisation plant; a fertilizer plant, a process steam plant, and a clay washing plant. The extent of the Neyveli lignite field, the production capacity of the three mines, and the linkage and utilisation of lignite are all considered. Future perspective plans beyond the seventh five year plan are reviewed. The use of coke and fertilizer by the chemical industries is outlined, and ecology and environmental control are discussed.

  11. Combustion behaviour and deposition characteristics of Cynara Cardunculus/Greek lignite co-firing under various thermal shares in a thermal pilot-scale facility

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, Aaron; Maier, Joerg; Scheffknecht, Guenter [Stuttgart Univ. (Germany). Inst. of Combustion and Power Plant Technology; Pawlak-Kruczek, Halina [Wroclaw Univ. of Technology (Poland). Inst. of Heat Engineering and Fluid Mechanics; Karampinis, Emmanouil; Grammelis, Panagiotis; Kakaras, Emmanuel [Centre for Research and Technology Hellas, Ptolemais (Greece). Chemical Process and Energy Resources Inst.; National Technical Univ. of Athens (Greece). Lab. of Steam Boilers and Thermal Plants

    2013-06-01

    The combustion of herbaceous biomass in industrial boilers, either as co-firing fuel or in dedicated combustion units, possess significant operating challenges due to increased risks for corrosion and slagging/fouling. The present work aims at investigating the combustion behaviour of Cynara Cardunculus (cardoon) in a range of thermal shares (0 to 100 %) with a Greek lignite. Combustion tests were performed in a 0.5 MW thermal input pulverised fuel pilot-scale test facility. Deposits were characterised in terms of morphological and ash fusion behaviour, and slagging/fouling tendencies were determined. (orig.)

  12. Synthesis of inorganic polymers using fly ash and primary lead slag.

    Science.gov (United States)

    Onisei, S; Pontikes, Y; Van Gerven, T; Angelopoulos, G N; Velea, T; Predica, V; Moldovan, P

    2012-02-29

    The present work reports on the synthesis and properties of inorganic polymers ("geopolymers") made of 100% fly ash from lignite's combustion, 100% primary lead slag and mixtures of the two. In the inorganic polymers with both fly ash and lead slag the main crystalline phases detected are wüstite, magnetite, sodium zinc silicate, quartz, anorthite, and gehlenite; litharge partially dissolves. FTIR analysis in these samples revealed that the main peaks and bands of end members also exist, along with a new amorphous reaction product. In terms of microstructure, both fly ash and lead slag dissolve and contribute in the binding phase whereas the larger particles act as aggregates. For an increasing lead slag in the composition, the binding phase is changing in chemistry and reaches PbO values higher than 50 wt.% for the 100% lead slag inorganic polymer. Regarding the properties of fly ash and lead slag inorganic polymers, compressive strength is higher than 35 MPa in all cases and water absorption diminishes as the lead slag content increases. A comparison of leaching results before and after polymerisation reveals that pH is an important factor as Pb is immobilised in the binding phase, unlike Zn and As. Copyright © 2011 Elsevier B.V. All rights reserved.

  13. Advanced control - technologies for suppressing harmful emission in lignitic coal-fired power generation

    International Nuclear Information System (INIS)

    Mir, S.; Hai, S.M.A.

    2000-01-01

    The production of sufficient amount of indigenous energy is a prerequisite for the prosperity of a nation. Pakistan's energy demand far exceeds its indigenous supplies. A cursory look at the energy situation in Pakistan reveals that there is an urgent need for the development of its energy resources. In this regard, coal can play a key role if its problems of high-sulfur and high ash can be rectified through the adoption adaptation of advanced technologies, like (I) clean coal technologies, and (II) control technologies. A review on clean coal technologies for utilization of lignitic coals has already been published and the present article describes the effect of harmful emissions from the combustion of high sulfur coals, like the ones found in Pakistan and their control through advanced control technologies, to make a significant contribution in the total energy economics of Pakistan. (author)

  14. Coal fly ash based carbons for SO2 removal from flue gases.

    Science.gov (United States)

    Rubio, B; Izquierdo, M T

    2010-07-01

    Two different coal fly ashes coming from the burning of two coals of different rank have been used as a precursor for the preparation of steam activated carbons. The performance of these activated carbons in the SO(2) removal was evaluated at flue gas conditions (100 degrees C, 1000 ppmv SO(2), 5% O(2), 6% H(2)O). Different techniques were used to determine the physical and chemical characteristics of the samples in order to explain the differences found in their behaviour. A superior SO(2) removal capacity was shown by the activated carbon obtained using the fly ash coming from a sub-bituminous-lignite blend. Experimental results indicated that the presence of higher amount of certain metallic oxides (Ca, Fe) in the carbon-rich fraction of this fly ash probably has promoted a deeper gasification in the activation with steam. A more suitable surface chemistry and textural properties have been obtained in this case which explains the higher efficiency shown by this sample in the SO(2) removal. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

  15. Main characteristics of the radioactive enrichment in ashes produced in coal-fired power stations

    International Nuclear Information System (INIS)

    Baeza, Antonio; Corbacho, Jose A.; Cancio, David; Robles, Beatriz; Mora, Juan C.

    2008-01-01

    Under contract with the Spain's 'Nuclear Safety Council', a study is being conducted of the nation's largest nominal output coal-fired power stations. Its purpose is to assess the radiological impact on workers and local populations due to this source of NORM activity. One of the aspects of particular interest is the study of the radioactive enrichment in the combustion wastes relative to the different coals used as fuel (usually local bituminous coal or lignite, or imported coal). These wastes consist of fly ash (mostly fine particles collected in electrostatic precipitators), and bottom ash (larger in size, and collected wet or dry in hoppers below the boilers). In general terms, the enrichment factors measured were between 2 and 18 for the radionuclides 40 K, 226 Ra, 232 Th, and 210 Po. The magnitude of this enrichment factor depended mainly on the ash content of each coal, and hence on the type of coal used as fuel and the specific operation cycle in the different power stations. For the radionuclides 40 K, 226 Ra, and 232 Th, the enrichment was relatively similar in value in the fly and bottom ashes produced by the different types of coal used in the power stations studied. For 210 Po, however, as was expected, the enrichment was much greater in the fly ash than in the bottom ash for each coal analyzed. (author)

  16. Transformation of heavy metals in lignite during supercritical water gasification

    International Nuclear Information System (INIS)

    Chen, Guifang; Yang, Xinfei; Chen, Shouyan; Dong, Yong; Cui, Lin; Zhang, Yong; Wang, Peng; Zhao, Xiqiang; Ma, Chunyuan

    2017-01-01

    Highlights: • The transformations of heavy metals during lignite SCWG were investigated. • The risks of heavy metals in lignite and residues after SCWG were evaluated. • The effects of experimental conditions on corrosion during SCWG were studied. - Abstract: Transformation characteristics of heavy metals during lignite supercritical water gasification (SCWG) were studied. A sequential extraction procedure (modified Tessier method) was used to selectively extract different fractions of Pb, Cd, Cr, Mn, Cu, Ni, and Zn. Heavy metals transformed into more stable fractions after SCWG. For Pb, Cd, Mn, Cu, and Zn, SCWG reduced the bioavailability and the risks posed by heavy metals in lignite. Under the experimental conditions, the conversion rates for Pb and Cd were 16.0%–25.2% and 16.3%–23.4%, respectively, whereas those for Mn, Cu, and Zn were much lower. Solid products enriched with Pb, Cd, Mn, Cu, and Zn were obtained after SCWG; the contents of these metals varied slightly in the liquid products under different experimental conditions. Excess Cr and Ni that did not originate from lignite were found in the residues, owing to reactor corrosion during lignite SCWG. Higher temperatures alleviated corrosion, whereas higher pressures and equivalence ratios (ER) had the opposite effect. None of the heavy metals were detected in the gas phase under the experimental conditions used in the present study. The correlation between the distributions of heavy metals and the experimental conditions were also studied. The transformation pathways of Pb, Cd, Mn, Cu, and Zn during SCWG were deduced according to the experimental results.

  17. Perspectives of the German lignite industry 2014; Perspektiven der deutschen Braunkohlenindustrie 2014

    Energy Technology Data Exchange (ETDEWEB)

    Hartung, Matthias; Milojcic, George [DEBRIV, Koeln (Germany)

    2014-11-01

    The decision to phase out nuclear energy and gradually realign the electricity system towards more renewables in the future required some extensive changes to electricity generation transmission. One of the issues to be considered is what role lignite can play in the transformation of the electricity system and what application is offered to Germany and its regions. However, lignite has some stable factors and their development is fairly predictable. Domestic lignite is one such example. Beyond its familiar attributes, 'secure, competitive and economically important for the regions', 'flexibility' is a key word that indicates a new dimension for the German lignite industry.

  18. Foreseen development of mining of lignite; Przewidywany rozwoj gornictwa wegla brunatnego

    Energy Technology Data Exchange (ETDEWEB)

    Kozlowski, Z. [Wroclaw University of Technology, Wroclaw (Poland). Dept. of Geo-engineering, Mining and Geology

    2004-07-01

    The future of activity in Poland's lignite sector will be determined by the demand for this fuel, which will in turn result from mining possibilities and economic competitiveness of the fuel in relation to other sources of electrical energy. The paper discusses all these factors and presents a framework programme for the development of Poland's lignite sector until 2040 (in detail) and further ahead to 2075, called the 'Agreement of manufacturers of lignite'. 4 refs., 5 tabs.

  19. JV Task 98 - Controlling Mercury Emissions for Utilities Firing Lignites from North America

    Energy Technology Data Exchange (ETDEWEB)

    Steven Benson

    2007-06-15

    This project compiled and summarized the findings and conclusions of research, development, and demonstration projects on controlling mercury from lignite coals. A significant amount of work has been conducted since 1994 on mercury in lignite, mercury measurement in flue gases, sorbent, sorbent enhancement additives, oxidation agent development, and full-scale demonstration of mercury control technologies. This report is focused on providing the lignite industry with an understanding of mercury issues associated with the combustion of lignite, as well as providing vital information on the methods to control mercury emissions in coal-fired power plants.

  20. Characteristics of Mae Moh lignite: Hardgrove grindability index and approximate work index

    Directory of Open Access Journals (Sweden)

    Wutthiphong Tara

    2012-02-01

    Full Text Available The purpose of this research was to preliminarily study the Mae Moh lignite grindability tests emphasizing onHardgrove grindability and approximate work index determination respectively. Firstly, the lignite samples were collected,prepared and analyzed for calorific value, total sulfur content, and proximate analysis. After that the Hardgrove grindabilitytest using ball-race test mill was performed. Knowing the Hardgrove indices, the Bond work indices of some samples wereestimated using the Aplan’s formula. The approximate work indices were determined by running a batch dry-grinding testusing a laboratory ball mill. Finally, the work indices obtained from both methods were compared. It was found that allsamples could be ranked as lignite B, using the heating value as criteria, if the content of mineral matter is neglected. Similarly,all samples can be classified as lignite with the Hargrove grindability indices ranging from about 40 to 50. However, there isa significant difference in the work indices derived from Hardgrove and simplified Bond grindability tests. This may be due todifference in variability of lignite properties and the test procedures. To obtain more accurate values of the lignite workindex, the time-consuming Bond procedure should be performed with a number of corrections for different milling conditions.With Hardgrove grindability indices and the work indices calculated from Aplan’s formula, capacity of the roller-racepulverizer and grindability of the Mae Moh lignite should be investigated in detail further.

  1. Nonisothermal Thermogravimetric Analysis of Thai Lignite with High CaO Content

    Science.gov (United States)

    Pintana, Pakamon

    2013-01-01

    Thermal behaviors and combustion kinetics of Thai lignite with different SO3-free CaO contents were investigated. Nonisothermal thermogravimetric method was carried out under oxygen environment at heating rates of 10, 30, and 50°C min−1 from ambient up to 1300°C. Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS) methods were adopted to estimate the apparent activation energy (E) for the thermal decomposition of these coals. Different thermal degradation behaviors were observed in lignites with low (14%) and high (42%) CaO content. Activation energy of the lignite combustion was found to vary with the conversion fraction. In comparison with the KAS method, higher E values were obtained by the FWO method for all conversions considered. High CaO lignite was observed to have higher activation energy than the low CaO coal. PMID:24250259

  2. Effect of Heterogeneity in Coal Ash Chemical Composition on the Onset of Conditions Favorable for Agglomeration in Fluid Beds

    Directory of Open Access Journals (Sweden)

    Aditi B. Khadilkar

    2015-11-01

    Full Text Available Ash agglomeration issues that arise due to the sticking of slag-wetted, colliding particles have been creating operational difficulties and monetary losses for the fluidized bed combustion (FBC industry. Difficulties have been experienced in the detection of slag-liquid at the low operating temperatures in fluidized bed combustors (FBCs and predicting the agglomeration behavior of fuel. This study aims to study the effect of heterogeneity in ash composition on the detection of slag-liquid in FBCs. It quantifies the slag-liquid amounts at the particle-level, under oxidizing environments, by dividing the bulk fuel into density classes. FactSage™ thermodynamic simulations of each of the particle classes, along with experimental validation of the trends with thermo-mechanical analysis (TMA and high temperature X-ray diffraction (HT-XRD were performed. The results obtained can be used to estimate the stickiness of particles in the development of ash agglomeration models based on particle collisions. The study of these particle classes shows that particle classes with specific minerals can form low temperature eutectics and lead to onset of slag-liquid formation at temperatures below those predicted by bulk analysis alone. Comparison of the differences in slag-liquid formation tendencies under reducing and oxidizing environments is also presented.

  3. Expansion of Neyveli lignite mines

    Energy Technology Data Exchange (ETDEWEB)

    Kasturi, T S

    1982-06-01

    This paper describes activities at Neyveli lignite mines in the Tamil Nadu region of India. The equipment used, in mining and materials handling is described. Problems encountered in the conveyor transport system are described, and the solutions finally adopted are presented.

  4. Leaching of polycyclic aromatic hydrocarbons from power plant lignite ash--influence of parameters important for environmental pollution.

    Science.gov (United States)

    Pergal, Miodrag M; Relić, Dubravka; Tešić, Zivoslav Lj; Popović, Aleksandar R

    2014-03-01

    Nikola Tesla B power plant (TENT B), located at the Sava River, in Obrenovac, 50 km west from the Serbian's capital, Belgrade, is the second largest coal-fired power plant in the country, consisting of two blocks, each of 620 MW capacity. In order to investigate the threat polycyclic aromatic hydrocarbons (PAHs) from deposited coal ash, obtained by coal combustion in this power plant, can represent for the surrounding environment, samples of coal ash were submitted to extraction with river water used for transport of coal ash to the dump, as well as with water of different ionic strength and acidity. It was found that, out of 16 EPA priority PAHs, only naphthalene, acenaphthylene, fluorene, phenantrene, fluoranthene, and pyrene were found in measurable concentrations in the different extracts. Their combined concentration was around 0.1 μg/L, so they do not, in terms of leached concentrations, represent serious danger for the surrounding environment. In all cases of established (and leached) PAH compounds, changes of ionic strength, acidity, or the presence of organic compounds in river water may to some extent influence the leached concentrations. However, under the examined conditions, similar to those present in the environment, leached concentrations were not more than 50 % greater than the concentrations leached by distilled water. Therefore, water desorption is likely the most important mechanism responsible for leaching of PAH compounds from filter coal ash.

  5. Environmental remediation with products of fluidized bed combustion

    International Nuclear Information System (INIS)

    Kim, A.G.

    1999-01-01

    Commercialization of fluidized bed combustion (FBC) technology could be enhanced by increased utilization of FBC products (ash). In the US, coal combustion products (CCP) are not hazardous under RCRA and are regulated as residual waste by the states. The composition of CCP from fluidized beds is primarily determined by the inorganic constituents in coal, the sorbent reaction products and the unreacted sorbent. The combustion system and the inclusion of other fuels may also affect the chemical composition, physical properties and leaching behavior. The alkalinity of the FBC material, residual lime and pozzolanic properties are desirable characteristics for use in soil stabilization and mine reclamation. At reclaimed surface coal mines, placement of CCP is intended to reduce the amount of acid mine drainage (AMD) produced at such sites. Neutralization, inhibition of acid forming bacteria, encapsulation of the pyrite or water diversion are believed to be the mechanisms facilitated by the alkaline material. Comparison of water quality, before and after injection of a grout composed of FBC ash and water indicated small increases in pH and decreases in acidity at discharge points. The concentrations of calcium and magnesium in water samples generally increased compared to background levels. The average concentration of trace elements (arsenic, cobalt, copper, nickel and zinc) was slightly elevated in the injection areas, but in down dip and discharge water samples were comparable to background levels. Over a four year period, the average acidity in the injected area decreased by approximately 30%, a value similar to another site where a mixture of class F fly ash and cement was injected. Although coal mine remediation is a beneficial environmental use of FBC products, its effectiveness may be related to the amount of FBCB used and the method of emplacement

  6. Environmental remediation with products of fluidized bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    Kim, A.G.

    1999-07-01

    Commercialization of fluidized bed combustion (FBC) technology could be enhanced by increased utilization of FBC products (ash). In the US, coal combustion products (CCP) are not hazardous under RCRA and are regulated as residual waste by the states. The composition of CCP from fluidized beds is primarily determined by the inorganic constituents in coal, the sorbent reaction products and the unreacted sorbent. The combustion system and the inclusion of other fuels may also affect the chemical composition, physical properties and leaching behavior. The alkalinity of the FBC material, residual lime and pozzolanic properties are desirable characteristics for use in soil stabilization and mine reclamation. At reclaimed surface coal mines, placement of CCP is intended to reduce the amount of acid mine drainage (AMD) produced at such sites. Neutralization, inhibition of acid forming bacteria, encapsulation of the pyrite or water diversion are believed to be the mechanisms facilitated by the alkaline material. Comparison of water quality, before and after injection of a grout composed of FBC ash and water indicated small increases in pH and decreases in acidity at discharge points. The concentrations of calcium and magnesium in water samples generally increased compared to background levels. The average concentration of trace elements (arsenic, cobalt, copper, nickel and zinc) was slightly elevated in the injection areas, but in down dip and discharge water samples were comparable to background levels. Over a four year period, the average acidity in the injected area decreased by approximately 30%, a value similar to another site where a mixture of class F fly ash and cement was injected. Although coal mine remediation is a beneficial environmental use of FBC products, its effectiveness may be related to the amount of FBCB used and the method of emplacement.

  7. Effects of lignite application on ammonia and nitrous oxide emissions from cattle pens

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Jianlei, E-mail: su@unimelb.edu.au [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia); Bai, Mei [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia); Shen, Jianlin [Institute of Subtropical Agriculture, Chinese Academy of Sciences, Changsha 410125 (China); Griffith, David W.T. [Department of Chemistry, University of Wollongong, NSW 2522 (Australia); Denmead, Owen T. [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia); Hill, Julian [Ternes Agricultural Consulting Pty Ltd, Upwey, VIC 3158 (Australia); Lam, Shu Kee; Mosier, Arvin R. [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia); Chen, Deli, E-mail: delichen@unimelb.edu.au [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia)

    2016-09-15

    Beef cattle feedlots are a major source of ammonia (NH{sub 3}) emissions from livestock industries. We investigated the effects of lignite surface applications on NH{sub 3} and nitrous oxide (N{sub 2}O) emissions from beef cattle feedlot pens. Two rates of lignite, 3 and 6 kg m{sup −2}, were tested in the treatment pen. No lignite was applied in the control pen. Twenty-four Black Angus steers were fed identical commercial rations in each pen. We measured NH{sub 3} and N{sub 2}O concentrations continuously from 4th Sep to 13th Nov 2014 using Quantum Cascade Laser (QCL) NH{sub 3} analysers and a closed-path Fourier Transform Infrared Spectroscopy analyser (CP-FTIR) in conjunction with the integrated horizontal flux method to calculate NH{sub 3} and N{sub 2}O fluxes. During the feeding period, 16 and 26% of the excreted nitrogen (N) (240 g N head{sup −1} day{sup −1}) was lost via NH{sub 3} volatilization from the control pen, while lignite application decreased NH{sub 3} volatilization to 12 and 18% of the excreted N, for Phase 1 and Phase 2, respectively. Compared to the control pen, lignite application decreased NH{sub 3} emissions by approximately 30%. Nitrous oxide emissions from the cattle pens were small, 0.10 and 0.14 g N{sub 2}O-N head{sup −1} day{sup −1} (< 0.1% of excreted N) for the control pen, for Phase 1 and Phase 2, respectively. Lignite application increased direct N{sub 2}O emissions by 40 and 57%, to 0.14 and 0.22 g N{sub 2}O-N head{sup −1} day{sup −1}, for Phase 1 and Phase 2, respectively. The increase in N{sub 2}O emissions resulting from lignite application was counteracted by the lower indirect N{sub 2}O emission due to decreased NH{sub 3} volatilization. Using 1% as a default emission factor of deposited NH{sub 3} for indirect N{sub 2}O emissions, the application of lignite decreased total N{sub 2}O emissions. - Graphical abstract: Lignite application substantially decreased NH{sub 3} emissions from cattle feedlots and increased

  8. Petrological, geochemical and isotopic characteristics of lignite and calcified lignite from mining area Pesje, Velenje Basin, Slovenia

    Science.gov (United States)

    Vrabec, Mirijam; Markič, Miloš; Vrabec, Marko; Jaćimović, Radojko; Kanduč, Tjaša

    2014-05-01

    Lignite (organic rich) and calcified lignite (inorganic rich) samples from excavation field -50c mining area Pesje, Velenje Basin, Slovenia were investigated. During geological and structural mapping lignite and calcified lignite samples were systematically taken for determination of their petrological, geochemical and isotopic characteristics. Lignite is composed of fine detritical gelified matrix. At least five different types of calcified lignite were recognized forming laminations, calcifications after wood, petrified wood and complete replacements of lignite with carbonate. All measured parameters so far indicate geochemical processes during sedimentation of the Velenej Basin. After macroscopic description samples were split to organic and inorganic component (Ward, 1984) and powdered in an agate mortar for geochemical and isotopic analyses. Major and trace elements (As, B, Ba, Cd, Co, Cr, Cu, Hg, Mn, Mo, Sb, Se, Th, U, Zn) in these samples were determined by instrumental neutron activation analysis (INAA) using k-0 standardization method (Jaćimović et al, 2002). The isotopic composition of carbon and nitrogen was determined using a Europa 20-20 continuous flow IRMS ANCA-SL preparation module. A 1 mg amount of a sample was weighed in a tin capsule for carbon and 10 mg for nitrogen analysis. Samples for carbon analyses were pretreated with 1 M HCl to remove carbonates. Carbonate samples from carbonate-rich strata and calcified xylite were first roasted at 450 deg C (Krantz et al., 1987). Three miligrams of carbonate sample was transformed into CO2 by reaction with anhydrous H3PO4 at 55 deg C under vacuum (McCrea, 1950) and measured with GV 2003 isotope ratio mass spectrometer. Measured isotopic composition of oxygen as VPDB values was recalculated to the VSMOW reference standard to enable the comparison with data from other coal basins. SEM/EDXS of carbonate rich sediments was performed with JEOL JSM 5800 electron microanalyzer scanning electron microscope

  9. THERMODYNAMIC ANALYSIS OF CARBON SEQUESTRATION METHODS IN LIGNITE POWER PLANTS

    International Nuclear Information System (INIS)

    Koroneos J. Christopher; Sakiltzis Christos; Rovas C. Dimitrios

    2008-01-01

    The green house effect is a very pressing issue of our times due to the big impact it will have in the future of life in our planet. The temperature increase of the earth which is the major impact of the greenhouse effect may change forever the climate and the way of life in many countries. It may lead to the reduction of agricultural production and at the end to famine, in several nations. The minimization of CO2 emissions and the introduction of new energy sources is the only solution to the catastrophe that is coming if inaction prevails. The objective of this work is to analyze the methods of the CO2 removal from the flue gases of power plants that use solid fuels. It is especially fit to the Greek conditions where the main fuel used is lignite. Three methods have been examined and compared thermodynamically. These are: (a) Removal of CO2 from the flue gas stream by absorption, (b) The combustion of lignite with pure oxygen and (c) The gasification of lignite. The lignite used in the analysis is the Greek lignite, produced at the Western Macedonia mines. The power plant, before carbon sequestration, has an efficiency of 39%, producing 330MW of electric power. After sequestration, the CO2 is compressed to pressures between 80-110 atm, before its final disposal. In the first method, the sequestration of CO2 is done utilizing a catalyst. The operation requires electricity and high thermal load which is received from low pressure steam extracted from the turbines. Additionally, electricity is required for the compression of the CO2 to 100 bars. This leads to a lower efficiency of the power plant by by 13%. In the second method, the lignite combustion is done with pure O2 produced at an air separation unit. The flue gasses are made up of CO2 and water vapor. This method requires electricity for carbon dioxide compression and the Air Separation unit, thus, the power plant efficiency is lowered by 26%. In the lignite gasification method, the products are a mixture of

  10. Photosynthetic pigment concentrations, gas exchange and vegetative growth for selected monocots and dicots treated with two contrasting coal fly ashes

    Energy Technology Data Exchange (ETDEWEB)

    Yunusa, I.A.M.; Burchett, M.D.; Manoharan, V.; DeSilva, D.L.; Eamus, D.; Skilbeck, C.G. [University of Technology Sydney, Sydney, NSW (Australia). Dept. of Environmental Science

    2009-07-15

    There is uncertainty as to the rates of coal fly ash needed for optimum physiological processes and growth. In the current study we tested the hyothesis that photosynthetic pigments concentrations and CO{sub 2} assimilation (A) are more sensitive than dry weights in plants grown on media amended with coal fly ash. We applied the Terrestrial Plant Growth Test (Guideline 208) protocols of the Organization for Economic Cooperation and Development (OECD) to monocots (barley (Hordeum vulgare) and ryegrass (Secale cereale)) and dicots (canola (Brasica napus), radish (Raphanus sativus), field peas (Pisum sativum), and lucerne (Medicago sativa)) on media amended with fly ashes derived from semi-bituminous (gray ash) or lignite (red ash) coals at rates of 0, 2.5, 5.0, 10, or 20 Mg ha(-1). The red ash had higher elemental concentrations and salinity than the gray ash. Fly ash addition had no significant effect on germination by any of the six species. At moderate rates ({<=}10 Mg ha{sup -1}) both ashes increased (P < 0.05) growth rates and concentrations of chlorophylls a and b, but reduced carotenoid concentrations. Addition of either ash increased A in radish and transpiration in barley. Growth rates and final dry weights were reduced for all of the six test species when addition rates exceeded 10 Mg ha{sup -1} for gray ash and 5 Mg ha{sup -1} for red ash. We concluded that plant dry weights, rather than pigment concentrations and/or instantaneous rates of photosynthesis, are more consistent for assessing subsequent growth in plants supplied with fly ash.

  11. Germany's lignite industry in 2011; Die deutsche Braunkohlenindustrie im Jahr 2011

    Energy Technology Data Exchange (ETDEWEB)

    Maassen, Uwe [Bundesverband Braunkohle, Koeln (Germany); Statistik der Kohlenwirtschaft e.V., Koeln (Germany); Schiffer, Hans-Wilhelm [RWE Aktiengesellschaft, Essen (Germany)

    2012-05-15

    From 2010 to 2011, Germany's domestic lignite output edged up 4.2% from 169.4 mill. t to 176.5 mill. t. This output is equivalent to a net calorific value of 54.4 mill. tce; of the total output, 157.4 mill. t, or some 90% was used in utility power plants for public supply. That was 3.6% more than in the previous year; 15.5 mill. t was input in the factories of the lignite-mining industry to make solid products, while 2.6 mill. t was used to generate electricity in mine-mouth power plants. Other sales of raw lignite and changes in stocks accounted for 1.0 mill. t. Lignite made a 24.9% contribution toward Germany's total power generation in 2011. In 2011, lignite had an 11.7% share in primary-energy consumption, giving it slot four in Germany's energy-consumption balance after mineral oil (34.0%), natural gas (20.4%) and hard coal (12.6%). Renewable resources cover 10.9, while nuclear energy accounts for 8.8% and other energy sources for 1.6%. With output of 54.4 mill. tce, lignite held a share of 38,5% in Germany's primary-energy production of some 141.3 mill. tce. The contributions made by the other energy carriers to primary-energy production in 2011 were as follows: 12.3 mill. tce hard coal, 13.1 mill. tce gas, 3.9 mill tce mineral oil, 49.5 mill. tce renewables, and 8.1 mill. tce other energy sources. Of the total electricity that Germany produced in 2011, 24,9% was accounted for by lignite. This means that lignite led the ranking of the most important input energies for electricity generation in 2011, followed by renewables with 19.9% hard coal with 18.6%, nuclear energy with 17.6% and gas with 13.7%. Other energy sources made a 5.3% contribution to total gross power generation. The most important ratios for the contributions made by the various lignite-mining areas to Germany's energy supply was shown. CO{sub 2} emissions from lignite rose 3.7% from 168.7 mill. t in 2010 to 175 mill. t in 2011. In the entire period from 1990 to 2011, a

  12. Germany's lignite industry in 2012; Die deutsche Braunkohlenindustrie im Jahr 2012

    Energy Technology Data Exchange (ETDEWEB)

    Maassen, Uwe [Bundesverband Braunkohle, Statistik der Kohlenwirtschaft e.V., Koeln (Germany); Schiffer, Hans-Wilhelm [RWE Aktiengesellschaft, Essen (Germany). CEA-W Allgemeine Wirtschaftspolitik/Wissenschaft

    2013-05-15

    From 2011 to 2012, Germany's domestic lignite output edged up to 5.1% from 176.5 mill. t to 185.4 mill. t. This figure is equivalent to a net calorific value of 57.2 mill. tce. Of the total output, 166.3 mill. t, or some 90%, was used in utility power plants for the public supply, i.e. 5.7% more than in the previous year. In addition, 15.1 mill. t was input in the factories of the lignite-mining industry to make solid products, while 3.0 mill. t was used to generate electricity in mine-mouth power plants. Other sales of raw lignite and changes in stocks accounted for 1.0 mill. t. Lignite made a 25.7% contribution toward Germany's total power generation in 2012. In 2012, lignite had a 12.1% share in primary-energy consumption balance after mineral oil (33.1%), natural gas (21.6%) and hard coal (12.2%). Renewable resources cover 11.6%, while nuclear energy accounts for 8.0% and other energy sources for 1.4%. With output of 57.2 mill. tce, lignite held a share of 38.4% in Germany's primary-energy production of some 149 mill. tce in 2012. The contributions made by other energy carriers to primary-energy production in 2012 were as follows: 11.1 mill. tce hard coal, 13.3 mill. tce gas, 3.8 mill. tce mineral oil, 54.0 mill. tce renewables, and 9.5 mill. tce other energy sources. Of the total electricity amount that Germany produced in 2012, 25.7% was accounted for by lignite. This means that lignite led the ranking of the most important input energies for electricity generation in 2012, followed by renewables with 22.1%, hard coal with 19.1%, nuclear energy with 16.1% and gas with 11.3%. Other energy sources made a 5.7% contribution to total gross power generation. The most important ratios for the contributions made by the various lignite-mining areas to Germany's energy supply are shown. CO{sub 2} emissions from lignite rose 5.1% from 173.9 mill. t in 2011 to 182.8 mill. t in 2012. In the total period from 1990 to 2012, a decline of 159.4 mill. t, or

  13. Sulphation of oil shale ash under atmospheric and pressurized combustion conditions

    International Nuclear Information System (INIS)

    Kuelaots, I.; Yrjas, P.; Hupa, M.; Ots, A.

    1995-01-01

    One of the main problems in conventional combustion boilers firing pulverized oil shale is the corrosion and fouling of heating surfaces, which is caused by sulphur compounds. Another major problem, from the environmental point of view, are the high SO 2 emissions. Consequently, the amount of sulphur in flue gases must be reduced. One alternative to lower the SO 2 , concentration is the use of new technologies, such as pressurized fluidized bed combustion (PFBC). In FBC processes, the sulphur components are usually removed by the addition of limestone (CaCO 3 ) or dolomite (CaCO 3 x MgCO 3 ) into the bed. The calcium in these absorbents react with SO 2 , producing solid CaSO 4 . However, when burning oil shale, there would be no need to add limestone or dolomite into the bed, due to the initially high limestone content in the fuel (molar ratio Ca/S =10). The capture of sulphur by oil shale ashes has been studied using a pressurized thermogravimetric apparatus (PTGA). The chosen experimental conditions were typical for atmospheric and pressurized fluidized bed combustion. Four different materials were tested - one cyclone ash from an Estonian oil shale boiler, two size fractions of Estonian oil shale and, one fraction of Israeli oil shale. The cyclone ash was found to be the poorest sulphur absorbent. In general, the results from the sulphur capture experiments under both atmospheric and pressurized fluidized bed conditions showed that the oil shale can capture not only its own sulphur but also significant amounts of additional sulphur from another fuel if the fuels are mixed together. (author)

  14. Powerful boost for Indian lignite

    Energy Technology Data Exchange (ETDEWEB)

    1985-06-01

    The Neyveli Lignite Corporation (NLC) of India has begun the first phase of an expansion program that will open a second mine and boost lignite production in Tamil Nadu to nearly five times its present level within the next 15 years. Mining conditions at Neyveli are particularly difficult. The harsh abrasive overburden strata present severe and strenuous conditions; sticky and marshy surface clays, the presence of groundwater aquifers, the cyclonic and monsoonal climate and high stripping ratios are other problems. The overburden is drilled and blasted; in areas of sticky topsoil, non-stick liners for the buckets etc. are used. Adequate safeguards and infrastructure are being developed to deal with differing strata conditions. The conveyor transport system features slow, wider belt conveyors, changeover from fixed type roller to freely hanging garland type, interlinking of benches and specially designed drive heads. The groundwater aquifers are continuously depressurized by grid pumping from a series of pumps; boreholes have been sunk to 120 m.

  15. Sulfomethylated lignite salt as a sacrifical agent in oil recovery processes

    Energy Technology Data Exchange (ETDEWEB)

    Kudchadker, M.V.; Weiss, W.J.

    1978-02-07

    A process is described for recovering petroleum from oil reservoirs by secondary recovery methods. The process involves injecting via an injection well into the reservoir an aqueous solution of sulfomethylated lignite salt as a sacrificial agent to inhibit the deposition of surfactant and polymer on the reservoir matrix. The process is conducted by first injecting the lignite salt into the formation through the injection well and following it with either a polymer or a surfactant solution, which also may contain the lignite salt. The polymer or surfactant would then be followed by a drive fluid, such as water, to push the chemicals and oil to the production well. (18 claims)

  16. Thermal dewatering of lignite: Phase III - final report

    Energy Technology Data Exchange (ETDEWEB)

    Champagne, P J; Szladow, A J; Kybett, B D

    1981-01-01

    Phase III of this project extended the investigation of thermal dewatering on several lignite and peat samples at the temperature range up to 400 degrees C and investigated variables such as retention time, increased rates of heating and cooling, extent of trace element removal, effect of particle size and effect of dewatering under heavy and light oils. Lignites from three areas of Canada (Estevan and Coronach, Saskatchewan, and Onakawana, Ontario) and one peat sample (Garrick, Saskatchewan) were thermally dewatered. The equilibrium moisture values obtained for the dewatered products were as low as, or lower than those obtained in Phases I and II of this project (350 degrees C). However, the measured moisture contents of the thermally dewatered Saskatchewan lignites were somewhat higher than those measured in Phases I and II. The equilibrium moisture values and the moisture contents decreased with increasing temperature. An optimum balance between extent of dewatering and resulting steam pressures is obtained for a dewatering temperature between 300 and 350 degrees C. At these temperatures, residence times in the order of 15 minutes are required. (35 refs.)

  17. The lignite industry and regional development. Interactions exemplified by the Rhenish mining area

    International Nuclear Information System (INIS)

    Kulik, Lars; Voigt, Jens

    2013-01-01

    Even in times of globalised markets, the German lignite industry retains its local and regional roots. Viewed against this background, the relationship between lignite industry and regional actors, and the interactions between the two play a major role in the perspectives for this branch of Germany's energy sector. Today, the links between the lignite industry and regional bodies are those of a partnership at eye-level. This type of relationship between the industry and regional actors has led to new forms and methods of cooperation at various levels. This is particularly evident in the efforts to re-shape the regional structure, develop the structure of townships and strengthen the economic structure with lignite playing an important role and new partners which are gaining in importance. (orig.)

  18. Cheap carbon sorbents produced from lignite by catalytic pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, B.N.; Schchipko, M.L. [Inst. of Chemistry of Natural Organic Materials, Akademgorodok, Krasnoyarsk (Russian Federation)

    1995-12-01

    Some data are presented describing the new technology of carbon sorbent production from powdered lignite in the installation with fluidized bed of catalyst. It was shown the different types of char products with extended pore structure and high sorption ability can be produced from cheap and accessible lignite of Kansk-Achinsk coal pit in pilot installation with fluidized bed of Al-Cu-Cr oxide catalyst or catalytically active slag materials. In comparison with the conventional technologies of pyrolysis the catalytic pyrolysis allows to increase by 3-5 times the process productivity and to decrease significantly the formation of harmful compounds. The latter is accomplished by complete oxidation of gaseous pyrolysis products in the presence of catalysts and by avoiding the formation of pyrolysis tars - the source of cancerogenic compounds. The technology of cheap powdered sorbent production from lignites makes possible to obtain from lignite during the time of pyrolysis only a few seconds char products with porosity up to 0.6 cm{sup 3} /g, and specific surface area more than 400 m{sup 3} /g. Some methods of powdered chars molding into carbon materials with the different shape were proved for producing of firmness sorbents. Cheap carbon sorbents obtained by thermocatalytic pyrolysis can be successfully used in purification of different industrial pollutants as one-time sorbent or as adsorbents of long-term application with periodic regeneration.

  19. Technical viability of nitric leaching in the desulphurisation of lignite from the Teruel region. La lixiviacion nitrica como posibilidad tecnica en la desulfuracion de los lignitos de Teruel

    Energy Technology Data Exchange (ETDEWEB)

    Alvarez, R.; Clemente, C.; Gomez-Limon, D. (Esc. Tec. Sup. Ing. Min., Madrid (Spain))

    1989-11-01

    Studies of selective flocculation and sedimentation of Teruel lignite which is high in both pyritic and organic sulphur enabled the sulphur content to be reduced to just 4.25%. Tests have subsequently been carried out with nitric leaching and the sulphur content has been reduced to below the levels of organic sulphur in addition to reducing the ash content by 4 to 9%. The cost of the reagents was similar or lower than in other processes and practically all the coal was recovered. 11 refs., 1 fig., 4 tabs.

  20. Changes of chemical properties of humic acids from crude and fungal transformed lignite

    Energy Technology Data Exchange (ETDEWEB)

    LianHua Dong; Quan Yuan; HongLi Yuan [China Agricultural University, Beijing (China). College of Biological Science

    2006-12-15

    The development of biological processes for fossil energy utilization has received increasing attention in recent years. There are abundance of lignite resources in China and the lignite, a low-grade coal, can be transformed by a Penicillium sp. After fungal transformation, the contents of humic acid and water-soluble humic material increased from 38.6% to 55.1%, and from less than 4.0% to 28.2%, respectively. The differences in chemical properties of crude lignite humic acid (aHA), fungal transformed lignite humic acid (bHA) and water-soluble humic material from fungal transformed lignite (WS) were studied. Elemental analysis and size exclusion chromatography showed that the N content of bHA increased by 47.36% compared with aHA, and the molecular mass of bHA was smaller than aHA. And the WS with the smallest molecular mass contained most content of N. The {sup 13}C NMR and FT-IR spectra of aHA and bHA showed that aHA contained more aromatic structure than bHA. 44 refs., 3 figs., 2 tabs.

  1. Experimental studies on pulp and paper mill sludge ash behavior in fluidized bed combustors

    Energy Technology Data Exchange (ETDEWEB)

    Latva-Somppi, J. [VTT Chemical Technology, Espoo (Finland). Process Technology

    1998-11-01

    Ash formation during the fluidized bed combustion (FBC) of pulp and paper mill sludges has been experimentally studied on an industrial and bench scale. The methods included aerosol measurements, chemical and crystalline composition analyses, thermogravimetry and electron microscopy. Fly ash mass and number size distributions and elemental enrichment in submicron particles and bottom ash were measured. Fly ash, bottom ash and ash deposits were characterized and their formation mechanisms are discussed. During combustion the fine paper-making additives in sludge, clay minerals and calcite, sintered fanning porous agglomerates. The fly ash mass mean size was 7.5 - 15 lam and the supermicron particles included 93.6 - 97.3 % of the fly ash. Condensation of the volatilized inorganic species formed spherical submicron particles in the fly ash. Their mass concentration was almost negligible when co-firing paper mill sludges and wood. This suggests that the fraction of the volatilized inorganic species in the paper mill sludges was low. Results from pulp mill sludge and bark co-firing were different. A clear mass mode below 0.3 pm, presenting 2.2 - 5.0 weight-% of the fly ash was detected. The condensed species included K, Na, S and Cl. Their mass fraction was higher in the pulp mill sludge than in the paper mill sludge. Evidently this resulted in increased volatilization and formation of condensed particles. The following trace elements were enriched in the submicron ash during pulp mill sludge and wood co-firing: As, Cd, Rb and Pb. The main part of the volatile species was, however, captured in the bulk ash. Presumably, this was due to the high surface area concentration in the bulk ash. Sludge moisture was observed to reduce the inorganic species volatilization. Probably steam vaporization from the wet sludge through the burning layer decreased combustion temperatures on char surface and less char was produced. Hence, the volatilization of ash forming species was

  2. Energy and water conservation at lignite-fired power plants using drying and water recovery technologies

    International Nuclear Information System (INIS)

    Liu, Ming; Qin, Yuanzhi; Yan, Hui; Han, Xiaoqu; Chong, Daotong

    2015-01-01

    Highlights: • Pre-drying and water recovery technologies were used to conserve energy and water. • The energy and water conservation potential were analyzed with reference cases. • The air-cooling unit produces water when the water content of lignite is high enough. • Influences of main parameters on energy and water conservation were analyzed. - Abstract: Lignite is considered as a competitive energy raw material with high security of supply viewed from a global angle. However, lignite-fired power plants have many shortcomings, including high investment, low energy efficiency and high water use. To address these issues, the drying and water recovery technologies are integrated within lignite-fired power plants. Both air-cooling and wet-cooling units with three kinds of lignite as feeding fuel were analyzed quantitatively. Results showed that energy conservation and water conservation are obtained simultaneously. The power plant firing high moisture lignite becomes more environmental friendly with higher power generation efficiency and a lower water makeup rate than the one firing low moisture lignite. And further calculation revealed that the air-cooling unit needs no makeup water and even produces some water as it generates power, when the water carrying coefficient is higher than 40 g/MJ.

  3. The German lignite industry. Historical development, resources, technology, economic structures and environmental impact. Study

    International Nuclear Information System (INIS)

    2017-05-01

    Lignite has a key role to play in the transformation of the energy system due to its specific structural features in terms of industry, company history, policy, economics, the environment and regional structures. Understanding these structural features of the German lignite industry is an important requirement for classifying the significance of the lignite industry up to now and for the redesigning of this industrial sector. From these environmental, economic and regulatory structural characteristics, which are interwoven in a variety of ways, the incentives arise for the mining and power plant operators to react to energy price signals or energy policy steering. The aim of this research study is to define these structural features, to compile comprehensively the basic data and information that is not always transparently available, to understand the interactions, to enable the navigation of issues that are partly very complex, and to classify into the long-term developments that are especially important for political and social processes. In 2016 approx. 12 percent of German primary energy consumption was met using lignite. At the same time, lignite has the highest carbon dioxide (CO2) emissions of the fossil fuels; it currently accounts for approx. 19 percent of Germany's total greenhouse gas emissions as well as approx. 46 percent of the total CO2 emissions of the electricity sector. As a result of the mining of lignite and its conversion into electricity, substantial adverse impacts beyond the entry of greenhouse gases into the Earth's atmosphere arise for other environmental media. These impacts include half of Germany's mercury emissions, approx. a third of its sulfur dioxide emissions and approx. a tenth of its nitrogen oxide emissions. Lignite mining in open-cast mines takes up a substantial amount of landscape and soil and requires huge interventions in the water balance. Relatively high costs arise for the recultivation and rehabilitation of the open

  4. Appraisal of Hydrologic Information Needed in Anticipation of Lignite Mining in Lauderdale County, Tennessee

    Science.gov (United States)

    Parks, William Scott

    1981-01-01

    Lignite in western Tennessee occurs as lenses or beds at various stratigraphic horizons in the Coastal Plain sediments of Late Cretaceous and Tertiary age. The occurrence of this lignite has been known for many decades, but not until the energy crisis was it considered an important energy resource. In recent years, several energy companies have conducted extensive exploration programs in western Tennessee, and tremendous reserves of lignite have been found. From available information, Lauderdale County was selected as one of the counties where strip-mining of lignite will most likely occur. Lignite in this county occurs in the Jackson and Cockfield Formations, undivided, of Tertiary age. The hydrology of the county is known only from regional studies and the collection of some site-specific data. Therefore, in anticipation of the future mining of lignite, a plan is needed for obtaining hydrologic and geologic information to adequately define the hydrologic system before mining begins and to monitor the effects of strip-mining once it is begun. For this planning effort, available hydrologic, geologic, land use, and associated data were located and compiled; a summary description of the surface and shallow subsurface hydrologic system was prepared: the need for additional baseline hydrologic information was outlined; and plans to monitor the effects of strip-mining were proposed. This planning approach, although limited to a county area, has transferability to other Coastal Plain areas under consideration for strip-mining of lignite.

  5. The thar lignite project in the Sindh province, Pakistan

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, L. [RWE Power International, RE GmbH, Mining Dept., Koeln (Germany); Dittrich, W. [RWE Power International, RE GmbH, Mechanical and Electrical Dept., Koeln (Germany)

    2005-05-01

    A prospective area of the known lignite deposit located in the Thar region was investigated with regard to the future development of an opencast mine. For this purpose, a bankable feasibility study was prepared that evaluates all relevant facts and additional exploration activities. The study includes among others: Geological report; Opencast mine planning; Equipment and infrastructure planning; Assessment of staff requirements; Conceptual design of the power station; Anticipation of environmental aspects; Bankable costing for lignite mining and power generation. In conclusion, the development of an opencast mine and the construction of a 1000 MW power station are feasible in technical and economic terms. For the mine, the shovel/truck method was proposed since it offers cost advantages. For the power station, a closed cooling circuit and pre-drying of the lignite was recommended due to water shortage in the Thar desert. The resulting prices for power generation are usual market costs in Pakistan. (orig.)

  6. Chemical characterization and receptor modeling of PM10 in the surroundings of the opencast lignite mines of Western Macedonia, Greece.

    Science.gov (United States)

    Samara, Constantini; Argyropoulos, George; Grigoratos, Theodoros; Kouras, Αthanasios; Manoli, Εvangelia; Andreadou, Symela; Pavloudakis, Fragkiskos; Sahanidis, Chariton

    2018-05-01

    The Western Macedonian Lignite Center (WMLC) in northwestern Greece is the major lignite center in the Balkans feeding four major power plants of total power exceeding 4 GW. Concentrations of PM 10 (i.e., particulate matters with diameters ≤10 μm) are the main concern in the region, and the high levels observed are often attributed to the activities related to power generation. In this study, the contribution of fugitive dust emissions from the opencast lignite mines to the ambient levels of PM 10 in the surroundings was estimated by performing chemical mass balance (CMB) receptor modeling. For this purpose, PM 10 samples were concurrently collected at four receptor sites located in the periphery of the mine area during the cold and the warm periods of the year (November-December 2011 and August-September 2012), and analyzed for a total of 26 macro- and trace elements and ionic species (sulfate, nitrate, chloride). The robotic chemical mass balance (RCMB) model was employed for source identification/apportionment of PM 10 at each receptor site using as inputs the ambient concentrations and the chemical profiles of various sources including the major mine operations, the fly ash escaping the electrostatic filters of the power plants, and other primary and secondary sources. Mean measured PM 10 concentrations at the different sites ranged from 38 to 72 μg m -3 . The estimated total contribution of mines ranged between 9 and 22% in the cold period increasing to 36-42% in the dry warm period. Other significant sources were vehicular traffic, biomass burning, and secondary sulfate and nitrate aerosol. These results imply that more efficient measures to prevent and suppress fugitive dust emissions from the mines are needed.

  7. French pollution and German lignite

    International Nuclear Information System (INIS)

    Foos, Jacques

    2015-01-01

    After having recalled that the German energy transition is based on a complete shutting down of nuclear power stations to replace them by renewable energy sources on the one hand, and by coal (lignite, i.e. the dirtiest coal) and gas on the other hand to compensate the intermittency of the former ones, this article notices that pollution peaks occurred in France when an eastern of north-eastern wind was blowing, and not in case of western wind. The author then wanders whether this pollution comes from Germany, and more particularly from the releases of lignite-fuelled power stations. Then, the author comments the high level of pollution associated with coal extraction and exploitation in Germany, causing thousands of deaths and resulting in lung diseases or cancers, myocardial infractions. The author then makes a parallel between, on the one hand, the ignorance of this German pollution and, on the other hand, evacuation measures around Fukushima for a radioactivity which the author considers as less dangerous in terms of life expectancy

  8. The development of the Ptolemais lignite deposit, present situation and future perspective of the electrical energy market (Greece)

    International Nuclear Information System (INIS)

    Kavourides, Kostas

    1997-01-01

    PPC is by far the major producer of solid fuels in Greece. Currently the known exploitable reserves of solid fuels, are 4,0 billions tones of lignite and 4 billion cubic meters of peat. Mining of Lignite in Greece started in 1951 at the Aliveri underground mine and was continued at the open cast mines at Ptolemais (1955) and Megalopolis (1919). For more than 45 years. PPC has successfully exploited the Greece Lignite deposit for the production of electricity in order to satisfy the demand in Greece. Today PPC produces 60 million tons of lignite and handles approximately 275 million cubic meters of masses (overburden, lignite and interculated) per year. Lignite is the main energy resource in Greece and its combustion provides 75-80% of the electrical energy consumed in Greece.The Lignite Center of Ptolemais - Amyndeon (LCP-A) operated by the Greece PPC is located in northern Greece, about 110 km west of the city of Thessaloniki. The lignite deposits under exploitation cover an area. of 120 km 2 including 4000 Mt of proven geological reserves and 2700 Mt of exploitable lignite under current economic and technological criteria. Today LCP-A manages six active mines which in 1997 have a rate of handling 245 mil cubic meter of material and producing approx. 48 mil for of lignite. The continuous mining method which employs BWES, conveyors and strackers is the principal mining method used in all the lignite mines at the Ptolemais-Amyndeon Lignite Center. The implementation of selective mining procedures as well as discontinuous and /or combined mining methods differentiates the mining technology at the LCP-A from the respective technology applied in Germany lignite mines. The quality properties suggest that the lignite deposits in Greece are among the world's worst quality deposits exploited for energy production, where approximately 2 kg of lignite are consumed per I kWh of generated power. The main advantages of PPC'S coal orientated development program are the following

  9. Desulfurization of organic sulfur from lignite by an electron transfer process

    Energy Technology Data Exchange (ETDEWEB)

    Demirbas, A. [Selcuk University, Konya (Turkey). Dept. for Chemical Engineering

    2006-10-15

    This study is an attempt to desulfurize organic sulfur from lignite samples with ferrocyanide ion as the electron transferring agent. Effect of temperature, particle size and concentration of ferrocyanide ion on desulfurization from the lignite samples has been investigated. The desulfurization process has been found to be continuous and gradually increases with increase of temperature from 298 to 368 K. The particle size has no significant impact on sulfur removal from the lignite samples. Particle size has no profound impact on the amount of sulfur removal. The desulfurization reaction has been found to be dependent on the concentration of potassium ferrocyanide. Gradual increase in the concentration of potassium ferrocyanide raised the magnitude of desulfurization, but at a higher concentration, the variation is not significant.

  10. Lignite pre-treatment and its effect on bio-stimulative properties of respective lignite humic acids

    Energy Technology Data Exchange (ETDEWEB)

    Vlckova, Z.; Grasset, L.; Antosova, B.; Pekar, M.; Kucerik, J. [Brno University of Technology, Brno (Czech Republic). Faculty of Chemistry

    2009-09-15

    Humic acids originating from South-Moravian lignite were subjected to a comparative study with the aim to assess the alteration of their physico-chemical properties after various lignite pre-treatments. Physical modification was achieved with two organic acids, such as acetic acid and citric acid and chemical modification by nitric acid and hydrogene peroxide in various concentrations. Elemental analysis, solid-state NMR, GC-MS analysis of polyols and size exclusion chromatography were carried out for chemical-physical characterization of obtained humic acids. Their biological effect, in form of potassium and ammonium humates, was tested on maize (Zea mays) seedlings. In these tests, potassium humates achieved far better overall results than ammonium humates. Results were inter-correlated in order to appraise the influence of humic acids physical and chemical properties on biological activity. Surprisingly, fractions with the lowest molecular size (0-35 kDa) showed no correlation with bioactivity results (Pearson coefficient from 0.05 to -0.4). On the contrary, middle-sized fractions (35-175 kDa) showed highly significant positive correlation (Pearson coefficient up to 0.92) and the highest molecular-size-fractions (275-350 kDa) showed negative correlation (Pearson coefficient up to -0.75). These findings were identical for both potassium and ammonium humates. No connection was found between bioactivity of humates and polyols content which was remarkably high; it reached 150 mg per g of humic acids in the most extreme case of 5% hydrogene peroxide pre-treatment. In the final analysis, the preparation mode bore pivotal responsibility for the control of humic acids biological effect and showed the best results for potassium humates obtained from lignite pre-treated by acetic acid and by 2% hydrogen peroxide.

  11. Sustainable development of lignite production on open cast mines in Serbia

    Energy Technology Data Exchange (ETDEWEB)

    Darko Danicic; Slobodan Mitrovic; Vladimir Pavlovic; Sava Kovacev [Kolubara Metal, Vreoci (Serbia)

    2009-09-15

    Currently operated coalmines in Serbia (Kolubara and Kostolac) have production around 36 million tons of lignite, and over 108 million m{sup 3} of overburden. Consequently, sustainability of lignite production requires cost reduction and environmental protection, as well as capacity increase. In order to rationalise, and increase efficiency of Serbian lignite mines, it is necessary to focus the activities on major issues shown within the triangle of energy policy objectives (security of supply, competitive prices and environmental protection). Production process optimisation singled out several special programs. Equipment revitalization and modernization is necessary taking into account that majority of the currently operated machinery has a life up to 25 years. Production process automation would enable high level of technical operation in the field of open cast mines management. Lack of coal quality uniformity is the permanent problem resulting by great amounts of coal reserves to be used uneconomically. Planning and training at all levels and finally cooperative software for business procedures and work order management. The measures suggested are a key precondition for maintaining competitive position of lignite production on international level. 7 refs., 5 figs., 1 tab.

  12. Role of Neyveli Lignite in the energy map of India

    Energy Technology Data Exchange (ETDEWEB)

    Srinivasaraghavan, S

    1984-08-01

    The Neyveli Lignite Corporation (NLC), a government undertaking, has played an important role in power generation in the southern region of India by contributing about 35% of the energy consumed in Tamil Nadu for over two decades. Performance at the Neyveli Thermal Power Station demonstrates that it is more advantageous to make additions to thermal generating capacity at Neyvili using lignite. Exploration and development of the mines can support this expansion and make the southern region a nucleus for industrial development. 2 tables.

  13. The Evaluation Of Waste Plastic Burned With Lignite And Biomass

    OpenAIRE

    DURANAY, Neslihan; YILGIN, Melek

    2016-01-01

    In this work, the combustion behavior of pellets prepared from binary and triple blends of waste plastic, biomass and lignite was investigated in an experimental fixed bed combustion system. Market bags as plastic waste and the furniture factory waste powder as a source of biomass and Bingöl Karlıova coal as a lignite were used. The effect of process temperature and the plastic mixing ratio on the combustion behavior of pellets was studied. Combustion data obtained from varied bed temperature...

  14. Expansion of the Neyveli lignite mine, India

    Energy Technology Data Exchange (ETDEWEB)

    Kasturi, T S [Neyveli Lignite Corp. Ltd., Tamil Nadu (India); Streck, W [Gold (O.) G.m.b.H. und Co. K.G., Koeln (Germany, F.R.)

    1979-08-01

    After giving a picture of the difficult winning conditions at the Neyveli open-cast lignite mine, the author states the reasons for the expansions of the open-cast mine and describes the necessary measures and machinery.

  15. Production of rubbly culm coke from lignite

    Energy Technology Data Exchange (ETDEWEB)

    Koenigs, H B [Rheinische Braunkohlenwerke A.G., Koeln (Germany, F.R.). Hauptabteilung Kohleverarbeitung; Kurtz, R [Rheinische Braunkohlenwerke A.G., Frechen (Germany, F.R.). Abt. Verkokung und Chemie

    1977-08-01

    The article deals with the coke supply of the iron and steel industry, the design, function, and special features of the open-hearth, and describes the coking properties and applications of the culm coke produced from lignite.

  16. Sedimentologic and palynologic significance of finding tertiary lignites in an ancient rift zone lake (Chingla, Ethiopia). Vol. 2

    Energy Technology Data Exchange (ETDEWEB)

    Kedamawit, Y.; Bonnefille, R.; Faure, H.; Taieb, M.

    1984-01-01

    Oligocene-Pleistocene deposits at Chingla apparently lie atop Miocene basalts. The upper cross-section shows numerous lignite interlayers. This paper discusses mineral composition of lignites and enclosing rock. Palynologic analysis of the lignite cross-sections determined 23 layers.

  17. Biotechnological lignite conversion - a large-scale concept

    Energy Technology Data Exchange (ETDEWEB)

    Reich-Walber, M.; Meyrahn, H.; Felgener, G.W. [Rheinbraun AG, Koeln (Germany). Fuel Technology and Lab. Dept.

    1997-12-31

    Concerning the research on biotechnological lignite upgrading, Rheinbraun`s overall objective is the large-scale production of liquid and gaseous products for the energy and chemical/refinery sectors. The presentation outlines Rheinbraun`s technical concept for electricity production on the basis of biotechnologically solubilized lignite. A first rough cost estimate based on the assumptions described in the paper in detail and compared with the latest power plant generation shows the general cost efficiency of this technology despite the additional costs in respect of coal solubilization. The main reasons are low-cost process techniques for coal conversion on the one hand and cost reductions mainly in power plant technology (more efficient combustion processes and simplified gas clean-up) but also in coal transport (easy fuel handling) on the other hand. Moreover, it is hoped that an extended range of products will make it possible to widen the fields of lignite application. The presentation also points out that there is still a huge gap between this scenario and reality by limited microbiological knowledge. To close this gap Rheinbraun started a research project supported by the North-Rhine Westphalian government in 1995. Several leading biotechnological companies and institutes in Germany and the United States are involved in the project. The latest results of the current project will be presented in the paper. This includes fundamental research activities in the field of microbial coal conversion as well as investigations into bioreactor design and product treatment (dewatering, deashing and desulphurization). (orig.)

  18. Trigeneration integrated with absorption enhanced reforming of lignite and biomass

    Energy Technology Data Exchange (ETDEWEB)

    Yaodong Wang; Ye Huang; Anthony P. Roskilly [Newcastle University, Newcastle Upon Tyne (United Kingdom). Sir Joseph Swan Institute for Energy Research

    2009-10-15

    A technical investigation of an innovative trigeneration integrated with absorption enhanced reforming (AER) of lignite and biomass is carried out using the ECLIPSE process simulator. The system includes an internal combustion engine, an AER gasifier, a waste heat recovery and storage unit and an absorption refrigerator. The whole system is operated in the following sequence: The AER gasifier is used to generate hydrogen using lignite and biomass; the hydrogen generated is used to run the engine which drives a generator to produce electricity. Additionally, the heat recovery unit collects waste heat from the engine and is used to supply hot water and space heating. Furthermore, the waste heat is used to operate the absorption refrigerator. The electricity, heat and cooling can be used to meet the energy requirements for the households in a village, a resident building or a commercial building, or a supermarket. Within the study, the effects of lignite mixed with three different types of biomass (straw, willow and switch grass) on the system performance are investigated and the results are compared. The results show that it is feasible to use an AER system to reform the low quality fuels lignite and biomass to generate a cleaner fuel - hydrogen to replace fossil fuels (diesel or natural gas) and to fuel an engine based trigeneration system; the system works with high efficiencies and with a potential of carbon capture from the sorbent-regeneration process that would benefit the environment. 25 refs., 2 figs., 3 tabs.

  19. Effect of some pre-treatments on the adsorption of methylene blue by Balkaya lignite

    International Nuclear Information System (INIS)

    Karaca, S.; Guerses, A.; Bayrak, R.

    2004-01-01

    In this study, the effects of some pre-treatments, such as HCl treatment, demineralization and pyrolysis, under a CO 2 atmosphere at different temperatures on the adsorption of methylene blue by Balkaya lignite were investigated. The adsorption capacities of the samples were determined before and after these pre-treatments. In addition, the removals of pyritic and organic sulfur and ash contents for the same coal samples were also defined. It was found that the adsorption capacities of the samples decreased after these pre-treatments. The decrease in adsorption capacity with pyrolysis can be attributed to the changes in surface morphology and/or pore size distribution of the coal samples. On the other hand, the observed decrease in adsorption capacity with removal of carbonates and silicates shows that these minerals have an important effect on methylene blue adsorption, and the adsorption considerably occurs through electrostatic interactions. In addition, the obtained results showed that the organic sulfur presence in the coal matrix have a positive effect on the methylene blue adsorption

  20. Enhancing Carbon Reactivity in Mercury Control in Lignite-Fired Systems

    Energy Technology Data Exchange (ETDEWEB)

    Chad Wocken; Michael Holmes; John Pavlish; Jeffrey Thompson; Katie Brandt; Brandon Pavlish; Dennis Laudal; Kevin Galbreath; Michelle Olderbak

    2008-06-30

    This project was awarded through the U.S. Department of Energy (DOE) National Energy Technology Laboratory Program Solicitation DE-PS26-03NT41718-01. The Energy & Environmental Research Center (EERC) led a consortium-based effort to resolve mercury (Hg) control issues facing the lignite industry. The EERC team-the Electric Power Research Institute (EPRI); the URS Corporation; the Babcock & Wilcox Company; ADA-ES; Apogee; Basin Electric Power Cooperative; Otter Tail Power Company; Great River Energy; Texas Utilities; Montana-Dakota Utilities Co.; Minnkota Power Cooperative, Inc.; BNI Coal Ltd.; Dakota Westmoreland Corporation; the North American Coal Corporation; SaskPower; and the North Dakota Industrial Commission-demonstrated technologies that substantially enhanced the effectiveness of carbon sorbents to remove Hg from western fuel combustion gases and achieve a high level ({ge} 55% Hg removal) of cost-effective control. The results of this effort are applicable to virtually all utilities burning lignite and subbituminous coals in the United States and Canada. The enhancement processes were previously proven in pilot-scale and limited full-scale tests. Additional optimization testing continues on these enhancements. These four units included three lignite-fired units: Leland Olds Station Unit 1 (LOS1) and Stanton Station Unit 10 (SS10) near Stanton and Antelope Valley Station Unit 1 (AVS1) near Beulah and a subbituminous Powder River Basin (PRB)-fired unit: Stanton Station Unit 1 (SS1). This project was one of three conducted by the consortium under the DOE mercury program to systematically test Hg control technologies available for utilities burning lignite. The overall objective of the three projects was to field-test and verify options that may be applied cost-effectively by the lignite industry to reduce Hg emissions. The EERC, URS, and other team members tested sorbent injection technologies for plants equipped with electrostatic precipitators (ESPs) and

  1. Petrographic Composition of Lignite from the Lake Somerville Spillway (East-central Texas)

    Science.gov (United States)

    Pawelec, Sandra; Bielowicz, Barbara

    2017-12-01

    In the presented paper, the macroscopic and microscopic composition of lignite from Lake Somerville Spillway has been examined. The study area is the upper part of the Manning Formation, located north-west of Somerville in the central-eastern part of Texas. There are three exposures: NE, SW and MC (Main Central) with visible parts of late-Eocene lignite seams belonging to the Jackson Group. The Manning section is divided into four marine dominated parasequences (P1 through P4). Lignite samples outlining the P1 parasequence from the MC and NE outcrops and the argillate sample from the lower part of the P2 parasequence, NE outcrop. Macroscopic characterization was carried out based on lithological classifications of humic coal. On this basis, it has been shown that the main lithotype occurring in the deposit is detritic (matrix) coal with a high share of mineral matter. The maceral composition of coal was determined according to the ICCP guidelines. The macerals from liptinite group were determined under fluorescent light. The maceral group content analysis was performed with use of 500-600 equally spaced points on the surface of the polished sections. It has been found that the examined coal is dominated by macerals from the huminite group, with a share ranging from 20.8 to 65.3% volume, including atrinite (9.8-22.8% volume, 17.5% volume on average). In the examined coal, macerals from the inertinite group (10.1 to 44.8%), especially semifusinite (max. 13.9%), fusinite (max. 9.3%) and funginite (max. 6.3 %) are of particularly large share. In the liptinite group, particular attention was paid to the content of alginite (max. 4.5%) and bituminite (max. 1.3 %), which indicate the paralic sedimentation environment of the examined coal. Additionally, the variability of macerals and maceral groups within the exposures and levels of the P1 parasequence was examined. The last step was to compare lignite from Lake Somerville Spillway with other lignites belonging to the

  2. Decomposition and reduction of N2O over Limestone under FBC Conditions

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Jensen, Anker; Vaaben, Rikke

    1997-01-01

    The addition of limestone for sulfur retention in FBC has in many cases been observed to influence the emission of N2O. The catalytic activity of N2O over calcined Stevns Chalk for decomposition of N2O in a laboratory fixed bed quartz reactor was measured. It was found that calcined Stevns Chalk...... is a very active catalyst for N2O decomposition in an inert atmosphere, and the presence of 3 vol% CO increased the rate of N2O destruction by a factor of 5 due to the catalytic reduction of N2O by CO. The activity decreased with increasing CO2 concentration, and uncalcined or recarbonated limestone had...... negligible activity. Sulfation of the calcined limestone under oxidizing conditions lowered the activity, however sulfidation under reducing conditions showed that CaS is an active catalyst for the reduction of N2O by CO. Without CO present a gas solid reaction between N2O and CaS takes place and SO2...

  3. Wettability modification of Wender lignite by adsorption of dodecyl poly ethoxylated surfactants with different degree of ethoxylation: A molecular dynamics simulation study.

    Science.gov (United States)

    Zhang, Lei; Li, Bao; Xia, Yangchao; Liu, Shengyu

    2017-09-01

    Lignite is an important and useful fossil fuel in the world and the strong hydrophilicity of it limits its applications. Surfactant adsorption on lignite is an effective way to make it hydrophobic. In this work, aiming to examine the effect of the degree of ethoxylation on the adsorption behavior of dodecyl poly ethoxylated surfactants on lignite and the wettability modification of modified lignite by surfactant adsorption, different combined systems formed by surfactants, water and a model surface of Wender lignite have been studied using molecular dynamics simulation. The adsorption configurations vary with the degree of ethoxylation. At the same adsorption amounts, increasing the degree of ethoxylation can make the adsorption layer more compactness and bring stronger adsorption strength. The results of binding energy and its components show that the adsorption of alkyl polyoxyethylene ethers surfactant on lignite is physically adsorbed rather than electrostatically or chemisorbed. Meanwhile, van der Waals interaction plays a dominant role in the adsorption. The addition of surfactant could reduce the possibility of the interaction between water and lignite. Compared to the original lignite, the interaction between them is weakened after surfactant adsorption in water/surfactant/lignite system, thus strengthening the hydrophobicity of lignite. Similar to the adsorption strength, hydrophobicity of modified lignite increases with the increase of the degree of ethoxylation. The lignite surface properties are changed due to surfactant adsorption by analyzing the compositions of interaction energy and the change of hydrogen bonds. Copyright © 2017 Elsevier Inc. All rights reserved.

  4. Characteristics of Mae Moh lignite: Hardgrove grindability index and approximate work index

    OpenAIRE

    Wutthiphong Tara; Chairoj Rattanakawin

    2012-01-01

    The purpose of this research was to preliminarily study the Mae Moh lignite grindability tests emphasizing onHardgrove grindability and approximate work index determination respectively. Firstly, the lignite samples were collected,prepared and analyzed for calorific value, total sulfur content, and proximate analysis. After that the Hardgrove grindabilitytest using ball-race test mill was performed. Knowing the Hardgrove indices, the Bond work indices of some samples wereestimated using the A...

  5. Influence of chemical structure on carbon isotope composition of lignite

    Science.gov (United States)

    Erdenetsogt, Bat-Orshikh; Lee, Insung; Ko, Yoon-Joo; Mungunchimeg, Batsaikhan

    2017-04-01

    During the last two decades, a number of studies on carbon isotopes in terrestrial organic matter (OM) have been carried out and used to determine changes in paleoatmospheric δ13C value as well as assisting in paleoclimate analysis. Coal is abundant terrestrial OM. However, application of its δ13C value is very limited, because the understanding of changes in isotopic composition during coalification is relatively insufficient. The purpose of this study was to examine the influence of the chemical structure on the carbon isotope composition of lignite. Generally, lignite has more complex chemical structures than other higher rank coal because of the existence of various types of oxygen-containing functional groups that are eliminated at higher rank level. A total of sixteen Lower Cretaceous lignite samples from Baganuur mine (Mongolia) were studied by ultimate, stable carbon isotope and solid-state 13C CP/MAS NMR analyses. The carbon contents of the samples increase with increase in depth, whereas oxygen content decreases continuously. This is undoubtedly due to normal coalification process and also consistent with solid state NMR results. The δ13C values of the samples range from -23.54‰ to -21.34‰ and are enriched in 13C towards the lowermost samples. Based on the deconvolution of the NMR spectra, the ratios between carbons bonded to oxygen (60-90 ppm and 135-220 ppm) over carbons bonded to carbon and hydrogen (0-50 ppm and 90-135 ppm) were calculated for the samples. These correlate well with δ13C values (R2 0.88). The results indicate that the δ13C values of lignite are controlled by two mechanisms: (i) depletion in 13C as a result of loss of isotopically heavy oxygen-bounded carbons and (ii) enrichment in 13C caused by a loss of isotopically light methane from aliphatic and aromatic carbons. At the rank of lignite, coal is enriched in 13C because the amount of isotopically heavy CO2 and CO, released from coal as a result of changes in the chemical

  6. Data summary of municipal solid waste management alternatives. Volume 5, Appendix C, Fluidized-bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    None

    1992-10-01

    This appendix provides information on fluidized-bed combustion (FBC) technology as it has been applied to municipal waste combustion (MWC). A review of the literature was conducted to determine: (1) to what extent FBC technology has been applied to MWC, in terms of number and size of units was well as technology configuration; (2) the operating history of facilities employing FBC technology; and (3) the cost of these facilities as compared to conventional MSW installations. Where available in the literature, data on operating and performance characteristics are presented. Tabular comparisons of facility operating/cost data and emissions data have been complied and are presented. The literature review shows that FBC technology shows considerable promise in terms of providing improvements over conventional technology in areas such as NOx and acid gas control, and ash leachability. In addition, the most likely configuration to be applied to the first large scale FBC dedicated to municipal solid waste (MSW) will employ circulating bed (CFB) technology. Projected capital costs for the Robbins, Illinois 1600 ton per day CFB-based waste-to-energy facility are competitive with conventional systems, in the range of $125,000 per ton per day of MSW receiving capacity.

  7. Solid substrate fermentation of lignite by the coal-solubilizing mould, Trichoderma atroviride, in a new type of bioreactor

    Energy Technology Data Exchange (ETDEWEB)

    Holker, U.; Hofer, M. [University of Bonn, Bonn (Germany)

    2002-07-01

    Trichoderma atroviride CBS 349 is able to solubilize lignite. The mould was cultured under non-sterile conditions in a new type of bioreactor for solid substrate fermentation. German lignite (lithotype A, Bergheim) was used as complex solid substrate. Over 40 days 140 g of 1.5 kg lignite held in a 25 1-bioreactor was solubilized by the fungus.

  8. A comparative study of nitrogen conversion during pyrolysis of coconut fiber, its corresponding biochar and their blends with lignite.

    Science.gov (United States)

    Liu, Zhengang; Balasubramanian, Rajasekhar

    2014-01-01

    In the present study, the conversion of fuel-N to HCN and NH3 was investigated during rapid pyrolysis of raw biomass (coconut fiber), its corresponding biochar and their blends with lignite within a temperature range of 600-900°C. The results showed that the raw biomass and the biochar showed totally different nitrogen partitioning between NH3 and HCN. HCN was the dominant nitrogen pollutant from pyrolysis of raw biomass, while for the biochar pyrolysis the yield of NH3 was slightly higher than that of HCN. Synergistic interactions occurred within both raw biomass/lignite and biochar/lignite blends, especially for the biochar/lignite blend, and resulted in reduced yields of HCN and NH3, decreased the total nitrogen percentage retained in the char and promoted harmless N2 formation. These findings suggest that biochar/lignite co-firing for energy production may have the enhanced benefit of reduced emissions of nitrogen pollutants than raw biomass/lignite. Copyright © 2013 Elsevier Ltd. All rights reserved.

  9. Fates and roles of alkali and alkaline earth metal species during the pyrolysis and gasification of a Victorian lignite

    Energy Technology Data Exchange (ETDEWEB)

    Mody, D.; Wu, H.; Li, C. [Monash University, Vic. (Australia). CRC for Clean Power from Lignite, Dept. of Chemical Engineering

    2000-07-01

    The transformation of alkali and alkaline earth metal (AAEM) species in a Victorian lignite during the pyrolysis and subsequent gasification in CO{sub 2} was studied in a novel quartz fluidised-bed reactor. Lignite samples prepared by physically adding NaCl and ion-exchanging Na{sup +} and Ca{sup ++} into the lignite were used to investigate the effects of chemical forms and valency of the AAEM species in the substrate lignite on their transformation during pyrolysis and gasification. Carboxyl-bound Na was found to be less volatile than Na present as NaCl, but more volatile than carboxyl-bound Ca during pyrolysis at temperatures between 400 and 900{sup o}C. However, the carboxyl-bound Na was volatilised to a much greater extent than the carboxyl-bound Ca in the same lignite during pyrolysis. It was seen that the loading of NaCl into the lignite did not significantly affect the char reactivity in the fluidised-bed reactor at 900{sup o}C.

  10. A study relating to the conceptual design and cost estimates of the Saskatchewan Power Corporation lignite beneficiation process

    Energy Technology Data Exchange (ETDEWEB)

    Granatstein, D L; Champagne, P J; Szladow, A J

    1982-06-01

    The purpose is to provide technology for upgrading lignite to a cleaner fuel that is capable of improving utility plant operation and is more acceptable to the non-utility sector. Beneficiated lignite can provide a middle alternative between low-grade and high-grade fuels. The results for phase IV include a conceptual design for a lignite beneficiation plant and a marketing study for the product. The beneficiated lignite is cheaper to transport, easier to handle, cleaner, allows better plant operation with higher availability, reduced slagging and fouling, reduced sulphur, and lower operating and maintenance costs. 8 refs., 6 figs., 7 tabs.

  11. Natural radioactivity of coal and fly ash at the Nikola Tesla B TPP

    Directory of Open Access Journals (Sweden)

    Kisić Dragica M.

    2013-01-01

    Full Text Available Serbian thermal power plants (TPPs produce siliceous fly ash from lignite in the quantity of approximately 6 million tons per year. The potential market for the use of fly ash is operational, but for the time being, only used by cement producers. Fly ash radioactivity could be one of the major points of concern when larger use of fly ash is planned, particularly in the Serbian construction industry. Radioactivity measurements have been conducted regularly for decades. This paper presents the results of a ten-year fly ash radioactivity measurements at the Nikola Tesla B TPP located in Obrenovac. In addition, the paper compares the natural radionuclides coal content data combusted by the Nikola Tesla B TPP boilers coming from the Kolubara Basin and ash created during coal combustion. Fly ash created in the Nikola Tesla TPPs boilers is characterised by the increased concentration of the natural radionuclides content compared to coal. This is the so-called technologically enhanced natural radioactivity (Technologically Enhanced Occurring Radioactive Material - TENORM of industrial waste, whereas the average specific activities: 232Th in coal amount to 25.2 Bq/kg, and in fly ash and coal 84.2 Bq/kg and 238U 38.3 Bq/kg, respectively. Following the obtained natural radionuclides content results it may be concluded that the Nikola Tesla B TPP ash may be disposed into the environment. Ash may be used also in the construction industry (civil engineering. In building construction applications, ash share as the additive to other building materials depends from its physical and chemical characteristics, as well as from the radionuclides activity: 266Ra, 232Th and 40K. Unlike the thermal power plants regularly (once a year testing the specific natural radionuclides activity in the combusted coal and boiler fly ash, Electric Power Industry of Serbia has not performed large-scale investigations of the natural radionuclides content in coal within the Kolubara

  12. Power generation from lignite coal in Bulgaria - problems and solutions

    International Nuclear Information System (INIS)

    Batov, S.; Gadjanov, P.; Panchev, T.

    1997-01-01

    The bulk of lignite coal produced in Bulgaria is used as fuel for the thermal power plants (TPP) built in Maritsa East coal field. A small part of it goes to production of briquettes and to fuel the auxiliary power plants of industrial enterprises. The total installed capacity of the power plants in the region of Maritsa East is 2490 MW, and the electric power generated by them is about 30% of the total power generated in the country. It should be noted that these power plants were subjected to a number of rehabilitations aiming to improve their technical and economic parameters. Irrespective of that, however, solution has still to be sought to a number of problems related to utilisation of the low-grade lignite coal for power generation. On the whole, they can be divided in the following groups: Those related to lignite coal mining can be referred to the first group. Lignite coal is mined in comparatively complicated mining and geological conditions characterized mainly by earth creep and deformation. The second group of problems is related to coal quality control. It is a fact of major significance that the quality indices of coal keep changing all the time in uneven steps without any definite laws to govern it. That creates hard problems in the process of coal transportation, crushing and combustion. The next group of problems concerns operation and upgrading of the power generation equipment. That applies especially to the existing boilers which bum low-grade fuel in order to improve their operation in terms of higher thermal efficiency, controllability, reliability, improved environmental indices, etc. An increasingly high importance is attached to environmental impact problems incident to lignite coal utilisation. Abatement of sulphur oxide emissions and dust pollution is a problem solution of which cannot wait. The possibilities for partial solution of the environmental problems through increasing the thermal efficiency of facilities at the thermal Power

  13. Treatment of lignite tars, etc

    Energy Technology Data Exchange (ETDEWEB)

    1936-08-07

    A process is described for treating tars such as lignite tar, shale tar, or peat tar, and similar tars, characterized by the fact that the tar is rectified to about 240/sup 0/C and the residue brought to a temperature above 50/sup 0/C after diluting with a product of the type of gasoline or ligroin at about 30/sup 0/C and treated with selective solvents preferably low-boiling phenols and eventually with water.

  14. NOx and SO2 emission factors for Serbian lignite Kolubara

    Directory of Open Access Journals (Sweden)

    Jovanović Vladimir V.

    2012-01-01

    Full Text Available Emission factors are widely accepted tool for estimation of various pollutants emissions in USA and EU. Validity of emission factors is strongly related to experimental data on which they are based. This paper is a result of an effort to establish reliable NOx and SO2 emission factors for Serbian coals. The results of NOx and SO2 emissions estimations based on USA and EU emission factors from thermal power plants Nikola Tesla Obrenovac A and B utilizing the Serbian lignite Kolubara are compared with experimental data obtained during almost one decade (2000-2008 of emissions measurements. Experimental data are provided from regular annual emissions measurement along with operational parameters of the boiler and coal (lignite Kolubara ultimate and proximate analysis. Significant deviations of estimated from experimental data were observed for NOx, while the results for SO2 were satisfactory. Afterwards, the estimated and experimental data were plotted and linear regression between them established. Single parameter optimization was performed targeting the ideal slope of the regression line. Results of this optimization provided original NOx and SO2 emission factors for Kolubara lignite.

  15. The catalytic cracking mechanism of lignite pyrolysis char on tar

    International Nuclear Information System (INIS)

    Lei, Z.; Huibin, H.; Xiangling, S.; Zhenhua, M.; Lei, Z.

    2017-01-01

    The influence of different pyrolysis conditions for tar catalytic cracking will be analyzed according to the lignite pyrolysis char as catalyst on pyrolytic tar in this paper. The pyrolysis char what is the by-product of the cracking of coal has an abundant of pore structure and it has good catalytic activity. On this basis, making the modified catalyst when the pyrolysis char is activation and loads Fe by impregnation method. The cracking mechanism of lignite pyrolytic tar is explored by applying gas chromatograph to analyze splitting products of tar. The experimental results showed that: (1) The effect of tar cracking as the pyrolysis temperature, the heating rate, the volatilization of pyrolysis char and particle size increasing is better and better. The effect of the catalytic and cracking of lignite pyrolysis char in tar is best when the heating rate, the pyrolysis temperature, the volatiles of pyrolysis char, particle size is in specific conditions.(2) The activation of pyrolysis char can improve the catalytic effect of pyrolysis char on the tar cracking. But it reduces the effect of the tar cracking when the pyrolysis char is activation loading Fe. (author)

  16. JV Task 90 - Activated Carbon Production from North Dakota Lignite

    Energy Technology Data Exchange (ETDEWEB)

    Steven Benson; Charlene Crocker; Rokan Zaman; Mark Musich; Edwin Olson

    2008-03-31

    The Energy & Environmental Research Center (EERC) has pursued a research program for producing activated carbon from North Dakota lignite that can be competitive with commercial-grade activated carbon. As part of this effort, small-scale production of activated carbon was produced from Fort Union lignite. A conceptual design of a commercial activated carbon production plant was drawn, and a market assessment was performed to determine likely revenue streams for the produced carbon. Activated carbon was produced from lignite coal in both laboratory-scale fixed-bed reactors and in a small pilot-scale rotary kiln. The EERC was successfully able to upgrade the laboratory-scale activated carbon production system to a pilot-scale rotary kiln system. The activated carbon produced from North Dakota lignite was superior to commercial grade DARCO{reg_sign} FGD and Rheinbraun's HOK activated coke product with respect to iodine number. The iodine number of North Dakota lignite-derived activated carbon was between 600 and 800 mg I{sub 2}/g, whereas the iodine number of DARCO FGD was between 500 and 600 mg I{sub 2}/g, and the iodine number of Rheinbraun's HOK activated coke product was around 275 mg I{sub 2}/g. The EERC performed both bench-scale and pilot-scale mercury capture tests using the activated carbon made under various optimization process conditions. For comparison, the mercury capture capability of commercial DARCO FGD was also tested. The lab-scale apparatus is a thin fixed-bed mercury-screening system, which has been used by the EERC for many mercury capture screen tests. The pilot-scale systems included two combustion units, both equipped with an electrostatic precipitator (ESP). Activated carbons were also tested in a slipstream baghouse at a Texas power plant. The results indicated that the activated carbon produced from North Dakota lignite coal is capable of removing mercury from flue gas. The tests showed that activated carbon with the greatest

  17. Pyrolysis kinetics of phenols from lignite semicoking tar

    Energy Technology Data Exchange (ETDEWEB)

    Platonov, V.V.; Polovetskaya, O.S.; Proskuryakov, V.A.; Shavyrina, O.A. [Leo Tolstoy Tula State Pedag University, Tula (Russian Federation)

    2002-11-01

    The features of pyrolysis of phenols from lignite semicoking tar were studied. The activation energy and order of the reactions of accumulation of methane, hydrogen, carbon monoxide and dioxide, naphthalene and its methyl homologs, phenols, and isomeric cresols and dimethylphenols were determined.

  18. Environmental evaluation of sewage sludge co-combustion in a pilot FBC

    Energy Technology Data Exchange (ETDEWEB)

    M. Helena Lopes; P. Abelha; I. Cabrita; J.F.Santos Oliveira; I. Gulyurtlu [INETI/DEECA, Lisbon (Portugal)

    2003-07-01

    This paper presents a comparison of combustion of coal alone with that of a mixture of coal with sewage sludge with respect to flue gas emissions, the behaviour of heavy metals and potential environmental consequences of disposal of ashes produced. Co-combustion with sludge did not result in greater NOx, SO{sub 2}, HCl and CO emissions and the use of air staging and the addition of limestone proved to be effective to reduce NOx and SO{sub 2}. The mixing of sludge gave rise to an increase in amounts of heavy metals released, especially for Cd, Pb and Hg. However, as they were associated with particles greater than 1 {micro}m, the application of efficient flue gas treatment devices could decrease their emissions to the atmosphere. Metals were essentially retained in ashes captured in the bed and in the cyclones and most of the Hg was adsorbed in fly ashes that contained unburned carbon. The leachability of metals and organic matter present in the sludge decreased with combustion. The evaluation of the acid neutralization capacity (ANC) showed that ashes became more resistant to acidification than the parent sludge. Globally, this study concludes that the implication of the combustion of sludge is that it can reduce the negative impact on the environment compared with the traditional direct use of sludge in soils. 22 refs., 4 figs., 5 tabs.

  19. Environmental Assessment for Lignite Fuel Enhancement Project, Coal Creek Station, Great River Energy, Underwood, North Dakota

    Energy Technology Data Exchange (ETDEWEB)

    N/A

    2004-01-16

    The US Department of Energy (DOE) has prepared this EA to assess the environmental impacts of the commercial application of lignite fuel enhancement. The proposed demonstration project would be implemented at Great River Energy's Coal Creek Station near Underwood, North Dakota. The proposed project would demonstrate a technology to increase the heating value of lignite and other high-moisture coals by reducing the moisture in the fuels. Waste heat that would normally be sent to the cooling towers would be used to drive off a percentage of the moisture contained within the lignite. Application of this technology would be expected to boost power-generating efficiencies, provide economic cost savings for lignite and sub-bituminous power plants, and reduce air emissions. The proposed project would be constructed on a previously disturbed site within the Coal Creek Station and no negative impacts would occur in any environmental resource area.

  20. The origin and distribution of HAPs elements in relation to maceral composition of the A1 lignite bed (Paleocene, Calvert Bluff Formation, Wilcox Group), Calvert mine area, east-central Texas

    Science.gov (United States)

    Crowley, Sharon S.; Warwick, Peter D.; Ruppert, Leslie F.; Pontolillo, James

    1997-01-01

    The origin and distribution of twelve potentially Hazardous Air Pollutants (HAPs; As, Be, Cd, Cr, Co, Hg, Mn, Ni, Pb, Sb, Se, and U) identified in the 1990 Clean Air Act Amendments were examined in relation to the maceral composition of the A1 bed (Paleocene, Calvert Bluff Formation, Wilcox Group) of the Calvert mine in east-central Texas. The 3.2 m-thick A1 bed was divided into nine incremental channel samples (7 lignite samples and 2 shaley coal samples) on the basis of megascopic characteristics. Results indicate that As, Cd, Cr, Ni, Pb, Sb, and U are strongly correlated with ash yield and are enriched in the shaley coal samples. We infer that these elements are associated with inorganic constituents in the coal bed and may be derived from a penecontemporaneous stream channel located several kilometers southeast of the mining block. Of the HAPs elements studied, Mn and Hg are the most poorly correlated to ash yield. We infer an organic association for Mn; Hg may be associated with pyrite. The rest of the trace elements (Be, Co, and Se) are weakly correlated with ash yield. Further analytical work is necessary to determine the mode of occurrence for these elements. Overall, concentrations of the HAPs elements are generally similar to or less than those reported in previous studies of lignites of the Wilcox Group, east-central region, Texas. Petrographic analysis indicates the following ranges in composition for the seven lignite samples: liptinites (5–8%), huminites (88–95%), and inertinites (trace amounts to 7%). Samples from the middle portion of the A1 bed contain abundant crypto-eugelinite compared to the rest of the samples; this relationship suggests that the degradation of plant material was an important process during the development of the peat mire. With the exception of Hg and Mn, relatively low levels of the HAPs elements studied are found in the samples containing abundant crypto-eugelinite. We infer that the peat-forming environment for this

  1. Combustion characteristics and air pollutant formation during oxy-fuel co-combustion of microalgae and lignite.

    Science.gov (United States)

    Gao, Yuan; Tahmasebi, Arash; Dou, Jinxiao; Yu, Jianglong

    2016-05-01

    Oxy-fuel combustion of solid fuels is seen as one of the key technologies for carbon capture to reduce greenhouse gas emissions. The combustion characteristics of lignite coal, Chlorella vulgaris microalgae, and their blends under O2/N2 and O2/CO2 conditions were studied using a Thermogravimetric Analyzer-Mass Spectroscopy (TG-MS). During co-combustion of blends, three distinct peaks were observed and were attributed to C. vulgaris volatiles combustion, combustion of lignite, and combustion of microalgae char. Activation energy during combustion was calculated using iso-conventional method. Increasing the microalgae content in the blend resulted in an increase in activation energy for the blends combustion. The emissions of S- and N-species during blend fuel combustion were also investigated. The addition of microalgae to lignite during air combustion resulted in lower CO2, CO, and NO2 yields but enhanced NO, COS, and SO2 formation. During oxy-fuel co-combustion, the addition of microalgae to lignite enhanced the formation of gaseous species. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Fractal morphology in lignite coal: a small angle x-ray scattering investigation

    International Nuclear Information System (INIS)

    Chitra, R.; Sen, D.; Mazumder, S.; Chandrasekaran, K.S.

    1999-01-01

    Small angle x-ray scattering technique has been used to study the pore morphology in lignite coal from Neyveli lignite mine (Tamilnadu, India). The sample were collected from three different locations of the same mine. SAXS profiles from all the three samples show almost identical functionality, irrespective of the locations from where the samples were collected. SAXS experiment using two different wavelengths also exhibit same functionality indicating the absence of multiple scattering. The analysis indicates the surface fractal nature of the pore morphology. The surface fractal dimension is calculated to be 2.58. (author)

  3. Reactivity of chars prepared from the pyrolysis of a Victorian lignite under a wide range of conditions

    Energy Technology Data Exchange (ETDEWEB)

    Wu, H.; Mody, D.; Li, C.; Hayashi, J.; Chiba, T. [Monash University, Vic. (Australia). CRC for Clean Power from Lignite, Dept. of Chemical Engineering

    2000-07-01

    A Loy Yang lignite sample was pyrolysed under a wide range of experimental conditions using a wire-mesh reactor, a fluidised-bed reactor, a drop-tube reformer and a thermogravimetric analyser (TGA). The reactivity of these char samples in CO{sub 2} and air was measured in the TGA as well as in the fluidised-bed reactor. A sample prepared by the physical impregnation of NaCl into the lignite was also used in order to investigate the effect of NaCl in the lignite on the reactivity of the resulting char. Our experimental results indicate that, due to the volatilisation of a substantial fraction of Na in the lignite substrate during pyrolysis, the true catalytic activity of the Na in the lignite substrate should be evaluated by measuring the sodium content in the char after pyrolysis. The char reactivity measured in situ in the fluidised-bed reactor was compared with that of the same char measured separately in the TGA after re-heating the char sample to the same temperature as that in the fluidised-bed. It was found that the re-heating of the char in the TGA reduced the char reactivity.

  4. Report on the survey of abandoned uraniferous lignite mines in southwestern North Dakota

    International Nuclear Information System (INIS)

    Lyon, R.J.; Prochaska, D.; Burgess, J.L.; Patrick, D.

    1986-03-01

    A radiation survey was conducted in October 1983 as part of the proposed reclamation plan of abandoned uraniferous lignite mines in southwestern North Dakota. The survey was made to determine the extent of contamination caused by mining operations in the 1960's. Radiation measurements were made and soil samples were taken at approximately 300 locations around six mine sites comprising eleven lignite mine pits. Toxic element analysis was also done on 50 of the soil samples

  5. LARGE-SCALE MECURY CONTROL TECHNOLOGY TESTING FOR LIGNITE-FIRED UTILITIES-OXIDATION SYSTEMS FOR WET FGD

    Energy Technology Data Exchange (ETDEWEB)

    Michael J. Holmes; Steven A. Benson; Jeffrey S. Thompson

    2004-03-01

    The Energy & Environmental Research Center (EERC) is conducting a consortium-based effort directed toward resolving the mercury (Hg) control issues facing the lignite industry. Specifically, the EERC team--the EERC, EPRI, URS, ADA-ES, Babcock & Wilcox, the North Dakota Industrial Commission, SaskPower, and the Mercury Task Force, which includes Basin Electric Power Cooperative, Otter Tail Power Company, Great River Energy, Texas Utilities (TXU), Montana-Dakota Utilities Co., Minnkota Power Cooperative, BNI Coal Ltd., Dakota Westmoreland Corporation, and the North American Coal Company--has undertaken a project to significantly and cost-effectively oxidize elemental mercury in lignite combustion gases, followed by capture in a wet scrubber. This approach will be applicable to virtually every lignite utility in the United States and Canada and potentially impact subbituminous utilities. The oxidation process is proven at the pilot-scale and in short-term full-scale tests. Additional optimization is continuing on oxidation technologies, and this project focuses on longer-term full-scale testing. The lignite industry has been proactive in advancing the understanding of and identifying control options for Hg in lignite combustion flue gases. Approximately 1 year ago, the EERC and EPRI began a series of Hg-related discussions with the Mercury Task Force as well as utilities firing Texas and Saskatchewan lignites. This project is one of three being undertaken by the consortium to perform large-scale Hg control technology testing to address the specific needs and challenges to be met in controlling Hg from lignite-fired power plants. This project involves Hg oxidation upstream of a system equipped with an electrostatic precipitator (ESP) followed by wet flue gas desulfurization (FGD). The team involved in conducting the technical aspects of the project includes the EERC, Babcock & Wilcox, URS, and ADA-ES. The host sites include Minnkota Power Cooperative Milton R. Young

  6. Spring Barley Yield Parameters after Lignite, Sodium Humate and Nitrogen Utilization

    Directory of Open Access Journals (Sweden)

    Kováčik Peter

    2016-10-01

    Full Text Available The existence of a small number of publications dealing with the impact of solid sodium humate and lignite on the quantity and quality of grown crops was the reason for establishing the field experiment. The objective of this experiment was to detect the impact of solid lignite and solid sodium humate on the quantity and quality of spring barley yield. These substances were applied into the soil either independently or along with nitrogen fertiliser. The next objective was to determine the impact of foliar application of sodium humate water solution applied either independently or along with nitrogen fertiliser on the quality and quantity of spring barley yield. The achieved results showed that the autumn application of solid lignite and the presowing application of solid sodium humate into the soil tended to decrease the yield of both grain and straw of spring barley, crude protein content in grain, proportion of the first-class grains and volume weight of grain, whereas the impact of humate was more negative. Lignite and sodium humate in the solid form should be used along with nitrogen fertiliser. The application of sodium humate in liquid form during the growth season of barley tended to increase the yield of both grain and straw. The joint application of nitrogen and liquid sodium humate during the growth season of barley increased the grain yield of barley significantly. A lower dose of nitrogen, applied during the growth season of barley (growth season BBCH 23, increased the grain yield of barley considerably more than a higher N dose, applied into the soil before barley sowing.

  7. Production of heavy greases from lignite

    Energy Technology Data Exchange (ETDEWEB)

    1921-03-18

    A process is described for the extraction of heavy greases and wagon greases and their equivalents, by separation from bitumins, resins, and waxes contained in lignite, peat, bituminous shale, fossil wax, paraffin, etc., characterized by the fact that for the extraction are used solvents of high boiling point, such as mineral oils, grease oils, tar oils, and other equivalents, which are not eliminated and at the same time constitute a part of the product obtained.

  8. Combined distiller waste utilisation and combustion gases desulphurisation method. The case study of soda-ash industry

    Energy Technology Data Exchange (ETDEWEB)

    Kasikowski, Tomasz; Buczkowski, Roman; Cichosz, Marcin; Lemanowska, Eliza [Faculty of Chemistry, Nicolas Copernicus University, ul. Gagarina 7, 87-100 Torun (Poland)

    2007-09-15

    In this paper, a concept of technology that can be helpful for lowering the negative influence of the synthetic (based on the Solvay process) soda ash plant on the natural environment is presented. We describe the desulphurisation of combustion gases from the factory's power plant, which is based on their absorption in the overflow of distiller waste. The excess of lime milk, which is added in the process of ammonia regeneration from filter liquor, results in a strong alkalinity of distiller waste. The high pH of distiller waste favours absorption of acidic combustion gases. The laboratory-scale tests showed about 80% efficiency of the desulphurisation process. The suspension samples we obtained consist mainly of CaCO{sub 3}. We suggest using the obtained solid phase as an adsorbent-insert in Fluidised Bed Combustion technology (FBC). Based on raw material prices, production costs, and average sell prices of the product, economic analysis of innovation was executed. Profits from employing the method presented come mainly from reduction of environmental fees. The sensitivity analysis of cost showed that the application of the desulphurisation process causes cost reduction in soda-ash production accounting for EUR 150 thousand per year (excluding depreciation) in Poland, and EUR 11,700 thousand per year (excluding depreciation) in Sweden. It has been found that the latter value is similar to the positive environmental impact of this innovation expressed in monetary units (EUR 10,350 thousand per year, excluding depreciation). (author)

  9. The atlas of major Appalachian gas plays. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-02-01

    This project will evaluate the technical, economic and environmental feasibility of filling abandoned underground mine voids with alkaline, advanced coal combustion wastes. Both pneumatic and hydraulic injection methods will be investigated. Success will be measured in terms of technical feasibility of the approach (i.e. % void filling), cost, environmental benefits (acid mine drainage and subsidence control) and environmental impacts (noxious ion release). Phase 1 is concerned with the development of the grout and a series of predictive models. Phase 1 will also redesign a pneumatic ejector, that was developed to stow limestone, to efficiently stow FBC ash. Phase 2 is a small scale field test at Anker Energy`s Fairfax mine. An inactive panel will be used to evaluate flow, strength, and pressure requirements for hydraulic (grout) injection. The Phase 2 pneumatic injection activities will take place at an Anker Energy mine in Preston County, West Virginia. Air flow requirements, pressure requirements, stowing rate (tons per hour), and stowing efficiency (distance blown) will be determined. Phase 3 is to take 26 months and will be a full scale test at Anker`s eleven acre Long Ridge mine site. The mine will be filled using both pneumatic and hydraulic injection methods. It is expected that the FBC ash will replace what is now an acid mine pool with an alkaline solid so that the ground water will tend to flow around rather than through the previously mined areas. The project will demonstrate whether FBC ash can be successfully disposed of in underground mines.

  10. Coating and melt induced agglomeration in a poultry litter fired fluidized bed combustor

    International Nuclear Information System (INIS)

    Billen, Pieter; Creemers, Benji; Costa, José; Van Caneghem, Jo; Vandecasteele, Carlo

    2014-01-01

    The combustion of poultry litter, which is rich in phosphorus, in a fluidized bed combustor (FBC) is associated with agglomeration problems, which can lead to bed defluidization and consequent shutdown of the installation. Whereas earlier research indicated coating induced agglomeration as the dominant mechanism for bed material agglomeration, it is shown experimentally in this paper that both coating and melt induced agglomeration occur. Coating induced agglomeration mainly takes place at the walls of the FBC, in the freeboard above the fluidized bed, where at the prevailing temperature the bed particles are partially molten and hence agglomerate. In the ash, P 2 O 5 forms together with CaO thermodynamically stable Ca 3 (PO 4 ) 2 , thus reducing the amount of calcium silicates in the ash. This results in K/Ca silicate mixtures with lower melting points. On the other hand, in-bed agglomeration is caused by thermodynamically unstable, low melting HPO 4 2− and H 2 PO 4 − salts present in the fuel. In the hot FBC these salts may melt, may cause bed particles to stick together and may subsequently react with Ca salts from the bed ash, forming a solid bridge of the stable Ca 3 (PO 4 ) 2 between multiple particles. - Highlights: • Coating induced agglomeration not due to K phosphates, but due to K silicates. • Melt induced agglomeration due to H 2 PO 4 − and HPO 4 2− salts in the fuel. • Wall agglomeration corresponds to coating induced mechanism. • In-bed agglomeration corresponds to melt induced mechanism

  11. Rapid restoration after lignite mining in Hungary

    Energy Technology Data Exchange (ETDEWEB)

    1988-06-01

    The 30th anniversary of the commencement of large scale lignite production by opencast mining in Hungary was celebrated in 1987. A process of rapid technical and biological reclamation without the use of humus has now been developed. The costs involved are only 5-10% of those of conventional methods and reclamation cycle is four years compared to ten years for conventional methods.

  12. Bioprocessing of lignite coals using reductive microorganisms. Final technical report, September 30, 1988--March 29, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, D.L.

    1992-03-29

    In order to convert lignite coals into liquid fuels, gases or chemical feedstock, the macromolecular structure of the coal must be broken down into low molecular weight fractions prior to further modification. Our research focused on this aspect of coal bioprocessing. We isolated, characterized and studied the lignite coal-depolymerizing organisms Streptomyces viridosporus T7A, Pseudomonas sp. DLC-62, unidentified bacterial strain DLC-BB2 and Gram-positive Bacillus megaterium strain DLC-21. In this research we showed that these bacteria are able to solubilize and depolymerize lignite coals using a combination of biological mechanisms including the excretion of coal solublizing basic chemical metabolites and extracellular coal depolymerizing enzymes.

  13. Combustion behavior of different kinds of torrefied biomass and their blends with lignite.

    Science.gov (United States)

    Toptas, Asli; Yildirim, Yeliz; Duman, Gozde; Yanik, Jale

    2015-02-01

    In this study, the combustion behavior of different kinds of torrefied biomass (lignocellulosic and animal wastes) and their blends with lignite was investigated via non-isothermal thermogravimetric method under air atmosphere. For comparison, combustion characteristics of raw biomasses were also determined. Torrefaction process improved the reactivity of char combustion step of biomasses. Characteristic combustion parameters for blends showed non-additivity behavior. It was found that the mixture of torrefied biomasses and lignite at a ratio of 1:1 had a lower ignition and burnout temperature than the coal-only sample. Although no interactions were observed between the lignite and torrefied biomass at initial step of combustion, a certain degree of interaction between the components occurred at char combustion step. Kinetic parameters of combustion were calculated by using the Coats Redfern model. Overall, this study showed that poultry litters can be used as a substitute fuel in coal/biomass co-firing systems by blending with lignocellulosic biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Differential-thermal analysis of irradiated lignite

    International Nuclear Information System (INIS)

    Chichek, F.; Eyubova, N.

    2006-01-01

    Full text: In this theme our purpose is to explain thermo-differential analysis of lignites irradiated. During experiment Caraman Ermenek (washed), Caraman Ermenek (crude), Nevshehir (crude), Slopi (crude), Trakya Harman (washed) lignite coals were used. Five of five kinds of coal samples with 3mm and 1gr of each sample were obtained. Then they were filled into the Tubes after having dried total 25 samples with 1 gr at 1000 degrees temperature for one hour. Air in the tubes was pumped out and closed. Coal samples in vacuum medium were irradiated by gamma rays of Co60 at 5.5 kGy, 19.2 kGy, 65.7 kGy, 169.6 kGy, 411.2 kGy doses to the normal conditions. Then differential thermal analysis was carried out both in original and the samples irradiated. Argon gas was used to make inert medium in the camera. T=200-8500 degrees temperature was selected. At the experiment done from 1000-1300 degrees temperatures too great endothermic reaction pick was begun to form by being observed thermal changings. At 3000-4200 degrees temperature exothermic reaction picks and at 7000 degrees parallel exothermic reaction picks were observed. Initial endothermic and exothermic reaction picks in five lignite samples were observed like a sharp curve. At the end coal irradiated samples were compared with original coal samples. At the result of experiment it was revealed that in comparison with original coal samples coal samples irradiated form exothermic and endothermic curves at very reaction pick and temperature intervals of these pick were large. Besides loss of weight was observed to begin at low temperatures in samples irradiated and especially momentary weight loss at some heats in the rang of known temperatures was observed in the coal Slopi contain in bitumen. Because of heat the weigh loss in the non irradiated samples forms parabolic curve and because of heat the weight loss in the samples irradiated forms stepped curves. It has shown that the coal irradiated can be easily departed by

  15. Influence of geological variations on lignite drying kinetics in superheated steam atmosphere for Belchatow deposit located in the central Poland

    Directory of Open Access Journals (Sweden)

    Sciazko Anna

    2016-01-01

    Full Text Available Lignite-fired coal power plants suffer from a significant heat loss due to the high moisture content in this energy carrier. Water removal from fuel is an indispensable treatment for improving the combustion process, which will foster the efficient utilization of lignite. Superheated steam fluidized bed drying is expected for this purpose in a power generation sector. Understanding drying kinetics of lignite will greatly reinforce design process of a dryer. Physical features as well as the drying behaviour may be divergent among the lignite originated from different depths and positions in a certain mine. To reveal and clarify the influence of the geological features, the drying characteristics of several grades of lignite from the Belchatow mine in Poland were investigated. The attempts to clarify the influence of the divergent properties of the investigated samples on the drying kinetics in superheated steam were presented in this paper.

  16. The reduction of sulfate ions in Musashino woody lignite and in acetone-furfural resin

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, T.

    1986-01-01

    By adding a barium chloride solution to sulfur-containing woody lignite kept in water for two years, it has been confirmed that large quantities of sulfate ions are adsorbed by the lignite. Furthermore, spectroscopic measurements have confirmed the reduction of sulfate ions in an acetone-furfural resin prepared with residual sulfuric acid. These experimental results suggest the possibility of reducing sulfate ions in coal in the absence of sulfate bacteria. 2 refs.

  17. Stabilization of ash from combustion of MSW in a fluidised bed boiler

    Energy Technology Data Exchange (ETDEWEB)

    Steenari, Britt-Marie; Wilewska, Magda [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Environmental Inorganic Chemistry

    2004-06-01

    Due to restrictions against the land filling of combustible waste and directives from authorities that favour energy recovery from the waste, combustion of household waste is becoming more common. Even though combustion of MSW reduces the volume of waste to be handled by approximately 90%, it produces ash residues containing most of the metals present in the original fuel and a number of other species carried through the boiler or formed during combustion. The residues can be divided into three categories: 1. Stable, inert ash that can be utilised in, for example, construction applications 2. Ash that is stable enough to be land filled as nonhazardous waste 3. Ash that contains large amounts of soluble components and potentially toxic metal species. The regulations considering leaching of ash components set limits for the release of soluble salts and toxic metals. Some fly ashes show low leachability for metals but gives a salt release that is too close to the limit for total dissolved solids. Since fly ash from FBC boilers represent the largest volume of ash from these boilers there is a need for a simple and cheap treatment method that reduces the amount of soluble salts, i.e. NaCl, KCl etc, in the ash. After stabilisation, the ash is supposed to go into a more stable category. The aim of this project has been to investigate the applicability of a method to wash such an ash with water. The work included laboratory studies of the ash properties, the water washing process, filtration properties of the ash slurry and also tests of the method in pilot scale at a full scale boiler. This work has been concentrated towards the investigation of cyclone ash from a bubbling fluidised bed boiler in Lidkoeping fired with 100% household waste. Elemental composition of ash samples before and after washing/filtration was determined by AAS or ICP after a suitable dissolution of the sample. The mineralogy of ash samples was analysed using X-ray powder diffractometry. This method

  18. PILOT-AND FULL-SCALE DEMONSTRATION OF ADVANCED MERCURY CONTROL TECHNOLOGIES FOR LIGNITE-FIRED POWER PLANTS

    Energy Technology Data Exchange (ETDEWEB)

    Steven A. Benson; Charlene R. Crocker; Kevin C. Galbreath; Jay R. Gunderson; Michael J. Holmes; Jason D. Laumb; Jill M. Mackenzie; Michelle R. Olderbak; John H. Pavlish; Li Yan; Ye Zhuang

    2005-02-01

    The overall objective of the project was to develop advanced innovative mercury control technologies to reduce mercury emissions by 50%-90% in flue gases typically found in North Dakota lignite-fired power plants at costs from one-half to three-quarters of current estimated costs. Power plants firing North Dakota lignite produce flue gases that contain >85% elemental mercury, which is difficult to collect. The specific objectives were focused on determining the feasibility of the following technologies: Hg oxidation for increased Hg capture in dry scrubbers, incorporation of additives and technologies that enhance Hg sorbent effectiveness in electrostatic precipitators (ESPs) and baghouses, the use of amended silicates in lignite-derived flue gases for Hg capture, and the use of Hg adsorbents within a baghouse. The approach to developing Hg control technologies for North Dakota lignites involved examining the feasibility of the following technologies: Hg capture upstream of an ESP using sorbent enhancement, Hg oxidation and control using dry scrubbers, enhanced oxidation at a full-scale power plant using tire-derived fuel and oxidizing catalysts, and testing of Hg control technologies in the Advanced Hybrid{trademark} filter.

  19. Experiments and stochastic simulations of lignite coal during pyrolysis and gasification

    International Nuclear Information System (INIS)

    Ahmed, I.I.; Gupta, A.K.

    2013-01-01

    Highlights: ► Lignite pyrolysis and gasification has been conducted in a semi batch reactor. ► The objective is to understand mechanism of syngas evolution during pyrolysis. ► Stochastic simulations of lignite pyrolysis were conducted using Gillespie algorithm. ► First order, single step mechanism failed to fit cumulative yield of hydrogen. ► Evolution of hydrogen via pyrolysis of gaseous hydrocarbon following bridges scission. -- Abstract: Lignite pyrolysis and gasification has been conducted in a semi batch reactor at reactor temperatures of 800–950 °C in 50 °C intervals. CO 2 has been used as the gasifying agent for gasification experiments. The objective of this investigation is to understand the mechanism of syngas evolution during pyrolysis and to unravel the effect of CO 2 on pyrolysis mechanism. Stochastic simulations of lignite pyrolysis have been conducted using Gillespie algorithm. Two reaction mechanisms have been used in the simulations; first order, single step mechanism and the FLASHCHAIN mechanism. The first order single step mechanism was successful in fitting cumulative yield of CO 2 , CO, CH 4 and other hydrocarbons (C n H m ). The first order, single step failed to fit the cumulative yield of hydrogen, which suggests a more complex mechanism for hydrogen evolution. Evolution of CO 2 , CO, CH 4 , C n H m and H 2 flow rates has been monitored. The only effect of CO 2 on pyrolysis mechanism is promotion of reverse water gas shift reaction for the experiments described here. Methane evolution extended for slightly longer time than other hydrocarbons and hydrogen evolution extended for a slightly longer time than methane. This indicated the evolution of hydrogen via further pyrolysis of aliphatic hydrocarbon. It is also suggested that this step occurs in series after aliphatic hydrocarbons evolution by bridges scission.

  20. Distribution of vesicular-arbuscular mycorrhizal fungi in coal, lignite and calcite mine spoils of India

    Energy Technology Data Exchange (ETDEWEB)

    Ganesan, V.; Ragupathy, S.; Parthipan, B.; Rani, D.B.R.; Mahadevan, A.

    1991-12-31

    Vesicular-arbuscular mycorhizzal (VAM) status was assessed for coal, lignite and calcite mine spoils. The three study sites were: The Kothagudem coal field in the south central region where waste materials are piled 1 to 2 m high on the soil surface. Samples were collected from plants growing on the waste. Neyveli, on the southeastern coast, is a lignite coal mine where the spoil is piled 70 to 100 m high on the soil surface. Samples were collected from recently revegetated mine spoil and from 25 year old revegetated sites. The calcite mine at Thazhaiyuthu in the south where the spoil is piled up 2 to 3 m on the soil surface. Samples were collected from 4 to 7 year old reclaimed sites. The wastes generally supported different plant species. The level of VAM infection of plants was markedly different in each mine spoil, with the maximum infection in the coal and calcite spoils, and the least in the lignite spoil. There was more infection in the 25 year old lignite spoil than in the newly revegetated spoil. There were different VAM species in each spoil, and no one species was present in all of the samples. The authors conclude that one of the factors leading to the differences between spoils is the amount of topsoil contained in the spoil (least in the lignite spoils which are very deep). The other is age of the spoils. Unfortunately the authors concluded that the best approach is to enrich the spoils with VAM rather than salvaging and replacing topsoil

  1. Petrology, palynology and organic geochemistry of Eocene lignite of Matanomadh, Kutch Basin, western India: Implications to depositional environment and hydrocarbon source potential

    Energy Technology Data Exchange (ETDEWEB)

    Dutta, Suryendu; Mathews, Runcie P.; Saraswati, Pratul K.; Banerjee, Santanu [Department of Earth Sciences, Indian Institute of Technology Bombay (India); Singh, Bhagwan D.; Tripathi, Suryakant M.; Singh, Alpana [Birbal Sahni Institute of Palaeobotany, Lucknow (India); Mann, Ulrich [Forschungszentrum Juelich (Germany). Institut fuer chemie und Dynamik der Geosphaere

    2011-01-01

    Petrological, palynological and organic-geochemical investigations were undertaken to determine the source vegetation, depositional conditions and hydrocarbon source potential of Eocene Matanomadh lignites from Kutch Basin, western India. The maceral study reveals that studied lignites are rich in huminite (av. 63%) with sub-ordinate amount of liptinite (av. 19%) and low inertinite (av. 3%), along with low to moderately high associated mineral matters (av. 15%). The overall petrographic composition points to a lagoonal condition for the formation of these lignites. The mean huminite reflectance values (R{sub r}: 0.28-0.34%, av. 0.31%) as well as low Rock-Eval T{sub max} (av. 417 C) values for the seams, suggest brown coal or lignitic stage/rank for the studied lignites. The palynological assemblages, dominated by tropical angiospermic pollen, suggest prevalence of warm humid tropical climate during the deposition of these lignites. The total organic carbon (TOC) content of lignites ranges between 26 and 58 wt.%, whereas the TOC content of the associated carbonaceous shales is around 4 wt.%. The Hydrogen Index (HI) ranging from 23 to 452 mg HC/g TOC indicates that the lignite sequence has the potential to produce mixed oil and gaseous hydrocarbons on maturation. The major pyrolysis products of lignites, derived from Curie point pyrolysis-GC-MS, are straight chain aliphatics, phenols and cadalene-based C{sub 15} bicyclic sesquiterpenoids. The exclusive occurrence of C{sub 15} bicyclic sesquiterpenoids suggests that these compounds are derived from dammar resin of angiosperm plants, belonging to family Dipterocarpaceae. (author)

  2. Perspectives of the non-energetic use of lignite in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Keller, D.; Sailer, B. [RWE Power AG, Essen (Germany)

    2013-11-01

    RWE Power AG as integral part of RWE Generation SE has been active in the development and commercialization of coal gasification routes for many years. RWE Generation SE is one of Europe's leading electricity producers and combines the expertise of the power plant specialists Essent (NL), RWE npower (UK) and RWE Power (D). A globally increasing freight traffic and accompanying fuel demand is anticipated in the future. This higher demand will probably result in an increase in crude oil price in the course of the next years. There will also be a disproportionately high increase in fuel prices additionally to the increase in the crude oil price due to an increasing treatment effort within refineries. Therefore the substitution of crude oil becomes more and more attractive in view of economical perspectives and security of supply. Crude oil is not only to be substituted as feedstock for fuels but also for the chemical industry. Coal has been and will be the most important feedstock for this. Especially its gasification enables various routes. In Germany there is also an interesting perspective for Coal-to-Liquids and Coal-to-Gas or CtL/CtG as the non-energetic use of coal is abbreviated. Lignite is available regardless of any market impacts and currently faces a change in its use for power generation due to the increasing use of renewable energies. Hence lignite is an attractive feedstock for CtL/CtG in Germany. The construction of a commercial size CtL/CtG plant means a billion Euro investment. So a reliable economic evaluation is inevitable. Today all CtL/CtG routes miss commercial competitiveness to the conventional production by some ten percents. In case the current upward price trend of crude oil continues CtL/CtG might become viable in the near future. The production of synthetic fuels appears most attractive in view of a substantial market potential. The further commercialization of gasification routes in Germany requires R and D activities especially

  3. Comparative study of German and Greek lignite mine reclamation

    International Nuclear Information System (INIS)

    Dietrich, N.L.

    1994-01-01

    The reclamation planning of three European lignite mining districts are compared: amount and extent of planning, integration with mining operations, and results. The districts are: Rheinbraun (Cologne), Leipzig-Borna (''East'' Germany), and Megalopolis (Greece). Lignite mines were visited and mining and reclamation personnel interviewed. The Rheinbraun mines have the most thorough reclamation operations. The integrated mine and reclamation operations are world class in size, scope, and detail of reclamation. A comprehensive landscape and reclamation plan is required in the mine permitting process. The Leipzig-Borna district is the second largest of the districts, studied little pre-mining planning of the post-mining landscape or land uses was evident. Reclamation is not closely integrated with the mining and typically occurs many years after the mining. Reduced lignite production since German reunification has left vast areas of disturbed land with little mining; and no funding for the reclamation of the large areas of mined land reclamation. The Greek Megalopolis mines have mine operations plan, but with no integrated reclamation planning. The initial spoil pile was reclaimed according to the original German mining plan. No pits have been reclaimed, and spoil areas are revegetated sporadically. The Rheinbraun mining operations Cologne which include a post mining landscape/land use plan have integrated and timely reclamation operations. The other two mining operations, which do not have a comprehensive and detailed reclamation and landscape/land use plans, do not integrate reclamation operations with the mining operations. The results are large areas of mined land unreclaimed for many years

  4. Potentials and limitations of spatial and demographic development in Kosovo-Metohija lignite basin

    Directory of Open Access Journals (Sweden)

    Spasić Nenad

    2009-01-01

    Full Text Available The initial research carried out for the purpose of elaborating the Spatial Plan for Kosovo-Metohija Lignite Basin indicated the need to address numerous conflicts and opposing interests in the area concerned. This required the Plan to focus on harmonizing the economic, social and spatial aspects of developing a mining-energy-industrial system (hereinafter MEIS and its surroundings, devising the new ways for the protection of local population interests and use of novel approaches in dealing with the environmental consequences of lignite exploitation and processing. The area wherein Kosovo-Metohija lignite deposits are found is replete with diverse conflicting interests, including insufficient and uneven development, extremely large overall and especially agrarian population density (among the highest in Europe, unemployment and a sizable portion of the grey economy, low level and quality of services of public interest, ethnic conflicts and polarization, etc. The environmental effects of MEIS activities in a situation of this kind were revealed by the early stages of research in all segments of economic, social and spatial development, along with a high degree of environmental degradation. The main conflict in the Plan area is the one between mining and agriculture, i.e. open pit lignite mining and high-fertility soil covering lignite deposits. The conflict is additionally aggravated by the remarkable density of agricultural population on this territory and high selling prices of the land. Therefore, a substantial part of the Plan’s propositions was related to the conditions of settlement and infrastructure relocation, population resettlement and measures to relieve the tensions and prevent the outbreak of potential conflicts in implementing the Plan. The Spatial Plan is conceived as a complex and comprehensive document defining the framework, basic principles, starting points and measures tackling the numerous development conflicts, spatial

  5. Mineralogy and geochemistry of density-separated Greek lignite fractions

    NARCIS (Netherlands)

    Iordanidis, A.; Doesburg, van J.D.J.

    2006-01-01

    In this study, lignite samples were collected from the Ptolemais region, northern Greece, homogenized, crushed to less than I nun, and separated in three density fractions using heavy media. The mineralogical investigation of the density fractions showed a predominance of pyrite in the light

  6. Fluidized bed and pulverized coal combustion residues for secondary pavements

    International Nuclear Information System (INIS)

    Ghafoori, N.; Diawara, H.; Wang, L.

    2009-01-01

    The United States produced nearly 125 million tons of coal combustion products in 2006. These by-products include fly ash, flue gas desulphurization materials, bottom ash, boiler slag, and other power plant by-products. The expense associated with waste disposal, lack of disposal sites, and significant environmental damage linked with the disposal of coal combustion residues have encouraged innovative utilization strategies such as the fluidized bed combustion (FBC) unit. This paper presented the results of a laboratory investigation that examined the properties of composites developed with different proportions of pre-conditioned FBC spent bed, pulverized coal combustion fly ash, natural fine aggregate, and Portland cement. The purpose of the study was to examine the extent to which the by-product composites could replace currently used materials in secondary roads. The paper presented the research objectives and experimental programs, including matrix constituent and proportions; mixture proportions; and mixing, curing, sampling, and testing. The discussion of results centered around compressive strength and expansion by internal sulfate attack. It was concluded that with proper proportioning, by-products of pulverized and fluidized bed combustion promote binding of sand particles and provide adequate strength under various curing and moisture conditions 4 refs., 6 tabs.

  7. Enhancement of mercury capture by the simultaneous addition of hydrogen bromide (HBr) and fly ashes in a slipstream facility.

    Science.gov (United States)

    Cao, Yan; Wang, Quan-Hai; Li, Jun; Cheng, Jen-Chieh; Chan, Chia-Chun; Cohron, Marten; Pan, Wei-Ping

    2009-04-15

    Low halogen content in tested Powder River Basin (PRB) coals and low loss of ignition content (LOI) in PRB-derived fly ash were likely responsible for higher elemental mercury content (averaging about 75%) in the flue gas and also lower mercury capture efficiency by electrostatic precipitator (ESP) and wet-FGD. To develop a cost-effective approach to mercury capture in a full-scale coal-fired utility boiler burning PRB coal, experiments were conducted adding hydrogen bromide (HBr) or simultaneously adding HBr and selected fly ashes in a slipstream reactor (0.152 x 0.152 m) under real flue gas conditions. The residence time of the flue gas inside the reactorwas about 1.4 s. The average temperature of the slipstream reactor was controlled at about 155 degrees C. Tests were organized into two phases. In Phase 1, only HBr was added to the slipstream reactor, and in Phase 2, HBr and selected fly ash were added simultaneously. HBr injection was effective (>90%) for mercury oxidation at a low temperature (155 degrees C) with an HBr addition concentration of about 4 ppm in the flue gas. Additionally, injected HBr enhanced mercury capture by PRB fly ash in the low-temperature range. The mercury capture efficiency, attesting conditions of the slipstream reactor, reached about 50% at an HBr injection concentration of 4 ppm in the flue gas. Compared to only the addition of HBr, simultaneously adding bituminous-derived fly ash in a minimum amount (30 lb/MMacf), together with HBr injection at 4 ppm, could increase mercury capture efficiency by 30%. Injection of lignite-derived fly ash at 30 lb/MMacf could achieve even higher mercury removal efficiency (an additional 35% mercury capture efficiency compared to HBr addition alone).

  8. An overview of underground coal gasification and its applicability for Turkish lignite

    Energy Technology Data Exchange (ETDEWEB)

    Pekpak, E.; Yoncaci, S.; Kilic, M.G. [Middle East Technical Univ., Ankara (Turkey). Dept. of Mining Engineering

    2010-07-01

    Coal is expected to maintain its significance as an energy source for a longer time period than oil and natural gas. Environmental concerns have led to the development of clean coal technologies, such as coal gasification. Coal gasification can be used at either at surface or in underground coal gasification (UCG). UCG has several advantages over surface gasification and conventional mining such as rank low calorific value coals. Coal gasification also has the potential to contribute to the energy supply of a country. Most Turkish coals are lignite and UCG may enable diversification of energy sources of Turkey and may help decrease external dependency on energy. This paper presented a study that matched a UCG technique to the most appropriate (Afsin Elbistan) lignite reserve in Turkey. Two UCG techniques were presented, including the linked vertical well method, and the directional drilling-controlled retractable injection point (CRIP) method. The properties of coal seams and coal properties were also outlined. It was concluded that Cobanbey is the most preferable sector in the Elbistan Lignite Reserve for a pilot study, and that the linked vertical well method could be considered as a candidate method. 17 refs., 6 tabs., 1 fig.

  9. A modern thermal power station operating on high-moisture lignite

    Energy Technology Data Exchange (ETDEWEB)

    V.R. Kotler; D.V. Sosin [All-Russia Thermal Engineering Institute (VTI), Moscow (Russian Federation)

    2009-07-01

    The boilers developed by the power machinery construction company Alstom for two power-generating units, the Maritsa East-II and Maritsa East-II, operating on high-moisture lignite from the Maritsa East field in Bulgaria are described.

  10. Solubilization of low-rank coal by Trichoderma atroviride: Evidence for the involvement of hydrolytic and oxidative enzymes by using C-14-labelled lignite

    Energy Technology Data Exchange (ETDEWEB)

    Holker, U.; Schmiers, H.; Grosse, S.; Winkelhofer, M.; Polsakiewicz, M.; Ludwig, S.; Dohse, J.; Hofer, M. [University of Bonn, Bonn (Germany). Inst. of Botany

    2002-04-01

    The deuteromycete Trichoderma atroviride is able to solubilize lignite in dependence on a given carbon source for growth. When cultivated on media containing glutamate, this mold excreted a set of different enzymes with hydrolytic activity. Addition of lignite to the growth media induced the synthesis of extracellular lignite-specific esterase activity but no evidence has been provided for its direct involvement in the process of lignite solubilization. Hence, the basic capability of T. atroviride enzymes to degrade a variety of ester and ether bonds at the surface or within the bulky lignite structure was tested using coal following its direct labelling with C-14-alkyl iodide. The participation of hydrolytic and oxidative enzymes in lignite degradation was assessed by measuring the release of C-14 radioactivity from selectively alkylated carboxylic and phenolic OH groups. T. atroviride cleaved both carboxylic esters using esterases and the phenolic ether bonds by using oxidative enzymes, most likely laccases.

  11. Production of metallurgical cokes from some Turkish lignites using sulphite liquor binders

    Energy Technology Data Exchange (ETDEWEB)

    Yanik, J.; Saglam, M.; Yuksel, M. (Ege University, Izmir (Turkey). Dept. of Chemistry)

    1990-04-01

    Soma and Tuncbilek lignites were briquetted at 80{degree}C under 0-100 MPa, using varying amounts of sulphite liquor binders. The briquettes were then carbonized at 950{degree}C, and the resulting formed cokes were examined. The effects of the type and concentration of binders, and of the briquetting pressure, on the strength and porosity of the formcokes were investigated. As a result of these experiments, optimal briquetting conditions were established. It was also stated that formcokes made from both Turkish lignite samples under optimal briquetting conditions could be used for metallurgical purposes, particularly in non-ferrous metallurgy. 17 refs., 1 fig., 4 tabs.

  12. Thermogravimetric investigation of the co-combustion between the pyrolysis oil distillation residue and lignite.

    Science.gov (United States)

    Li, Hao; Xia, Shuqian; Ma, Peisheng

    2016-10-01

    Co-combustion of lignite with distillation residue derived from rice straw pyrolysis oil was investigated by non-isothermal thermogravimetric analysis (TGA). The addition of distillation residue improved the reactivity and combustion efficiency of lignite, such as increasing the weight loss rate at peak temperature and decreasing the burnout temperature and the total burnout. With increasing distillation residue content in the blended fuels, the synergistic interactions between distillation residue and lignite firstly increased and then decreased during co-combustion stage. Results of XRF, FTIR, (13)C NMR and SEM analysis indicated that chemical structure, mineral components and morphology of samples have great influence on the synergistic interactions. The combustion mechanisms and kinetic parameters were calculated by the Coats Redfern model, suggesting that the lowest apparent activation energy (120.19kJ/mol) for the blended fuels was obtained by blending 60wt.% distillation residue during main co-combustion stage. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Exploring the impact of reduced hydro capacity and lignite resources on the Macedonian power sector development

    Directory of Open Access Journals (Sweden)

    Taseska-Gjorgievskaa Verica

    2014-01-01

    Full Text Available The reference development pathway of the Macedonian energy sector highlights the important role that lignite and hydro power play in the power sector, each accounting for 40% of total capacity in 2021. In 2030, this dominance continues, although hydro has a higher share due to the retirement of some of the existing lignite plants. Three sensitivity runs of the MARKAL-Macedonia energy system model have been undertaken to explore the importance of these technologies to the system, considering that their resource may be reduced with time: (1 Reducing the availability of lignite from domestic mines by 50% in 2030 (with limited capacity of imports, (2 Removing three large hydro options, which account for 310 MW in the business-as-usual case, and (3 Both of the above restrictions. The reduction in lignite availability is estimated to lead to additional overall system costs of 0.7%, compared to hydro restrictions at only 0.1%. With both restrictions applied, the additional costs rise to over 1%, amounting to 348 M€ over the 25 year planning horizon. In particular, costs are driven up by an increasing reliance on electricity imports. In all cases, the total electricity generation decreases, but import increases, which leads to a drop in capacity requirements. In both, the lignite and the hydro restricted cases, it is primarily gas-fired generation and imports that “fill the gap”. This highlights the importance of an increasingly diversified and efficient supply, which should be promoted through initiatives on renewables, energy efficiency, and lower carbon emissions.

  14. Production scheduling of a lignite mine under quality and reserves uncertainty

    International Nuclear Information System (INIS)

    Galetakis, Michael; Roumpos, Christos; Alevizos, George; Vamvuka, Despina

    2011-01-01

    The effect of uncertainty sources to the stochastic optimization of the combined project of a new surface lignite mine exploitation and power plant operation for electricity generation is investigated. Major sources of uncertainty that were considered are the reserves and the quality of the lignite. Since probability distribution functions for these uncertainties were estimated during the detailed exploration phase of the deposit, the overall goal is then to determine the optimal capacity of the power plant and consequently the optimal production rate of the mine over the time. The optimization objective that was selected is the maximization of the net present value of the project. Emphasis is placed on the sensitivity analysis for the investigation of the effect of quality and reserves uncertainty on project optimization, on the mathematical formulation of risk attitude strategy and on increasing the efficiency of the optimization process by creating a limited set of feasible solutions applying empirical rules. The developed methodology was applied for the determination of the optimal annual production rate of a new surface lignite mine in the area of Ptolemais–Amynteon in Northern Greece. - Highlights: ► Quality and reserves uncertainty affects considerably the production scheduling. ► Stochastic optimization is greatly accelerated by incorporating Taylor's rule. ► Decisions can be made considering different risk level attitudes.

  15. Major gaseous and PAH emissions from a fluidized-bed combustor firing rice husk with high combustion efficiency

    International Nuclear Information System (INIS)

    Janvijitsakul, Kasama; Kuprianov, Vladimir I.

    2008-01-01

    This experimental work investigated major gaseous (CO and NO x ) and PAH emissions from a 400 kW th fluidized-bed combustor with a cone-shaped bed (referred to as 'conical FBC') firing rice husk with high, over 99%, combustion efficiency. Experimental tests were carried out at the fuel feed rate of 80 kg/h for different values of excess air (EA). As revealed by the experimental results, EA had substantial effects on the axial CO and NO x concentration profiles and corresponding emissions from the combustor. The concentration (mg/kg-ash) and specific emission (μg/kW h) of twelve polycyclic aromatic hydrocarbons (PAHs), acenaphthylene, fluorene, phenanthrene, fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a,h]anthracene and indeno[1,2,3-cd]pyrene, were quantified in this work for different size fractions of ash emitted from the conical FBC firing rice husk at EA = 20.9%. The total PAHs emission was found to be predominant for the coarsest ash particles, due to the effects of a highly developed internal surface in a particle volume. The highest emission was shown by acenaphthylene, 4.1 μg/kW h, when the total yield of PAHs via fly ash was about 10 μg/kW h. (author)

  16. Determination of optimal environmental policy for reclamation of land unearthed in lignite mines - Strategy and tactics

    Science.gov (United States)

    Batzias, Dimitris F.; Pollalis, Yannis A.

    2012-12-01

    In this paper, optimal environmental policy for reclamation of land unearthed in lignite mines is defined as a strategic target. The tactics concerning the achievement of this target, includes estimation of optimal time lag between each lignite site (which is a segment of the whole lignite field) complete exploitation and its reclamation. Subsidizing of reclamation has been determined as a function of this time lag and relevant implementation is presented for parameter values valid for the Greek economy. We proved that the methodology we have developed gives reasonable quantitative results within the norms imposed by legislation. Moreover, the interconnection between strategy and tactics becomes evident, since the former causes the latter by deduction and the latter revises the former by induction in the time course of land reclamation.

  17. Carbonate and lignite cycles in the Ptolemais Basin: Orbital control and suborbital variability (Late Neogene, northern Greece)

    Science.gov (United States)

    Weber, M. E.; Tougiannidis, N.; Ricken, W.; Rolf, C.; Kleineder, M.; Bertram, N.; Antoniadis, P.

    2009-04-01

    We recently commenced a project to investigate deep drillings as well as outcrops in the Ptolemais Basin, northern Greece, for paleoenvironmental and paleoclimate change. Specific attention is paid to mining sites Achlada, Vevi, Vegora, Amynteon, North Field, South Field, and Lava. The sediment archive comprises Upper Miocene to Quaternary continental lake deposits (up to 800 m thick) with an extended Lower Pliocene section. The Upper Miocene sections are composed of diatomaceous mud and gray marls. Pliocene lake sediments commence with the Kyrio member (lignite/grey marl), followed by the Theodoxus member (beige marl/lignite), and the Notio member (marl with intercalated sand /lignite). The limnic deposits show striking rhythmic bedding of (mostly) carbonates and lignites, reflecting orbital-induced humidity and temperature changes in this small NW-SE elongated continental basin. First, we retrieved chronometric information by determining magnetic polarity changes on three sites as independent stratigraphic ground-truth in combination with palynological evidence and published data. Then we conducted a number of high-resolution (1 - 6 cm increment), non-destructive measurements to obtain paleoclimate proxies: photospectrometry (colors L, a, b), magnetic susceptibility, and natural gamma. Accordingly, we achieved a multi-proxy insight into paleoclimate and paleoenvironmental evolution at unprecedented temporal resolution (up to a few decades!) over long time series and at a number of key sites. Using the newly-developed ESALab software, we conducted spectral and evolutionary spectral analysis to evaluate the cyclo-stratigraphic development. As for orbital variability, spectral power is concentrated on precession, hemi-precession, and eccentricity, with only minor impact of orbital tilt. We used this information to increase the temporal resolution of our age models by tuning as many precession (insolation) maxima as possible to carbonate minima (lignite maxima

  18. Securing the future of the Lusatian lignite mining; Zukunftssicherung im Lausitzer Revier

    Energy Technology Data Exchange (ETDEWEB)

    Klocek, Gert [Vattenfall Europe Mining AG, Cottbus (Germany). Bergbauplanung; Ketzmer, Wolfgang [Vattenfall Europe Mining AG, Cottbus (Germany). Grunddaten und Bergtechnik

    2014-11-01

    In the course of securing the future of the Lusatian lignite mining, the company has initiated several measures and activities. Thus with large-scale projects such as relocating the operating and surface facilities of the Welzow-Sued opencast mine uninterrupted long-term mining advance is ensured. The company's lignite-fired power plants with their project ''FlexGen'', to further increased flexibility, enhances their position to master of the challenges of ''Energiewende''. The political and societal framework for this complex development is in line with the climate and energy programmes or strategies of the Free State of Saxony and the federal state of Brandenburg.

  19. EOSLT Consortium Biomass Co-firing. WP 4. Biomass co-firing in oxy-fuel combustion. Part 1. Lab- Scale Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Fryda, L.E. [ECN Biomass, Coal and Environmental Research, Petten (Netherlands)

    2011-07-15

    In the frame of WP4 of the EOS LT Co-firing program, the ash formation and deposition of selected coal/biomass blends under oxyfuel and air conditions were studied experimentally in the ECN lab scale coal combustor (LCS). The fuels used were Russian coal, South African coal and Greek Lignite, either combusted separately or in blends with cocoa and olive residue. The first trial period included tests with the Russian and South African coals and their blends with cocoa, the second trial period included Lignite with olive residue tests and a final period firing only Lignite and Russian coal, mainly to check and verify the observed results. During the testing, also enriched air combustion was applied, in order to establish conclusions whether a systematic trend on ash formation and deposition exists, ranging from conventional air, to enriched air (improving post combustion applications) until oxyfuel conditions. A horizontal deposition probe equipped with thermocouples and heat transfer sensors for on line data acquisition, and a cascade impactor (staged filter) to obtain size distributed ash samples including the submicron range at the reactor exit were used. The deposition ratio and the deposition propensity measured for the various experimental conditions were higher in all oxyfuel cases. No significant variations in the ash formation mechanisms and the ash composition were established. Finally the data obtained from the tests performed under air and oxy-fuel conditions were utilised for chemical equilibrium calculations in order to facilitate the interpretation of the measured data; the results indicate that temperature dependence and fuels/blends ash composition are the major factors affecting gaseous compound and ash composition rather than the combustion environment, which seems to affect neither the ash and fine ash (submicron) formation, nor the ash composition. The ash deposition mechanisms were studied in more detail in Part II of this report.

  20. Dry re-forming of methane to synthesis gas over lignite semicokes catalyst at high pressure

    Directory of Open Access Journals (Sweden)

    Fengbo Guo

    2016-11-01

    Full Text Available Dry re-forming of methane has been carried out in a high temperature–pressure reactor at different pressures, using Hongce lignite semicokes catalyst. The results show that CH4 and CO2 conversions are decreased as the reaction pressure increased, but both of them kept basically stable when the reaction pressure is between 0.3 and 1 MPa. The comparison shows that the effects of the temperature and the flow of reactant gas on dry re-forming of methane are consistent with between high pressure and atmospheric pressure. The ratio of CO/H2 decreased as the ratio of CH4/CO2 increased, yet the value of CO/H2 is always more than 1 at different pressures. Hongce lignite semicokes catalyst is characterized by FTIR, XRD, SEM and BET, and the analysis results reveled that the physical specific adsorption peak of CO2 at 2350 cm−1 is strengthened significantly at different pressures, the micropore area and volume of Hongce lignite semicokes reduced form 40.2 m2  g−1 and 0.019 cm3  g−1 to 34.9 m2  g−1 and 0.017 cm3  g−1, respectively. Hongce lignite semicokes catalyst exhibited better activity and stability within 0.3–1 MPa range.

  1. Activated-Lignite-Based Super Large Granular Slow-Release Fertilizers Improve Apple Tree Growth: Synthesis, Characterizations, and Laboratory and Field Evaluations.

    Science.gov (United States)

    Tang, Yafu; Wang, Xinying; Yang, Yuechao; Gao, Bin; Wan, Yongshan; Li, Yuncong C; Cheng, Dongdong

    2017-07-26

    In this work, lignite, a low-grade coal, was modified using the solid-phase activation method with the aid of a Pd/CeO 2 nanoparticle catalyst to improve its pore structure and nutrient absorption. Results indicate that the adsorption ability of the activated lignite to NO 3 - , NH 4 + , H 2 PO 4 - , and K + was significantly higher than that of raw lignite. The activated lignite was successfully combined with the polymeric slow-release fertilizer, which exhibits typical slow-release behavior, to prepare the super large granular activated lignite slow-release fertilizer (SAF). In addition to the slow-release ability, the SAF showed excellent water-retention capabilities. Soil column leaching experiments further confirmed the slow-release characteristics of the SAF with fertilizer nutrient loss greatly reduced in comparison to traditional and slow-release fertilizers. Furthermore, field tests of the SAF in an orchard showed that the novel SAF was better than other tested fertilizers in improve the growth of young apple trees. Findings from this study suggest that the newly developed SAF has great potential to be used in apple cultivation and production systems in the future.

  2. Genetic relationship of organic bases of the quinoline and isoquinoline series from lignite semicoking tars with the initial biological material

    Energy Technology Data Exchange (ETDEWEB)

    Platonov, V.V.; Proskuryakov, V.A.; Podshibyakin, S.I.; Domogatskii, V.V.; Shvykin, A.Y.; Shavyrina, O.A.; Chilachava, K.B. [Leo Tolstoy State Pedagog University, Tula (Russian Federation)

    2002-07-01

    The genetic relationship of quinoline and isoquinoline compounds present in semicoking tars of Kimovsk lignites (near-Moscow fields) with the initial vegetable material is discussed. Transformation pathways of the native compounds in the course of lignite formation are suggested.

  3. Synthetic fuel production using Texas lignite and a very high temperature reactor for process heat

    International Nuclear Information System (INIS)

    Ross, M.A.; Klein, D.E.

    1982-01-01

    Two approaches for synthetic fuel production from coal are studied using Texas lignite as the feedstock. First, the gasification and liquefaction of coal are accomplished using Lurgi gasifiers and Fischer-Tropsch synthesis. A 50 000 barrel/day facility, consuming 13.7 million tonne/yr (15.1 million ton/yr) of lignite, is considered. Second, a nuclear-assisted coal conversion approach is studied using a very high temperature gas-cooled reactor with a modified Lurgi gasifier and Fischer-Tropsch synthesis. The nuclear-assisted approach resulted in a 35% reduction in coal consumption. In addition, process steam consumption was reduced by one-half and the oxygen plants were eliminated in the nuclear assisted process. Both approaches resulted in a synthetic oil price higher than the March 1980 imported price of $29.65 per barrel: $36.15 for the lignite-only process and $35.16 for the nuclear-assisted process. No tax advantage was assumed for either process and the utility financing method was used for both economic calculations

  4. Differential-thermal analysis of irradiated lignite

    International Nuclear Information System (INIS)

    Chichek, F; Eyubova, N.

    2006-01-01

    Full text: In this theme our purpose is to explain thermo-differential analysis of lignite's irradiated. During experiment Caraman Ermenek (washed), Caraman Ermenek (crude), Nevshehir (crude), Slopi (crude), Trakya Harman (washed) lignite coals were used. Five of five kinds of coal samples with 3mm and 1 gr of each sample were obtained. Then they were filled into the Tubes after having dried total 25 samples with 1 gr at 1000C temperature for one hour. Air in the tubes was pumped out and closed. Coal samples in vacuum medium were irradiated by gamma rays of Co-60 at 5.5 kGy, 19.2 kGy, 65.7 kGy, 169.6 kGy, 411.2 kGy, doses to the normal conditions. At the end coal irradiated samples were compared with original coal samples. At the result of experiment it was revealed that in comparison with original coal samples coal samples irradiated from exothermic and endothermic curves at very reaction pick and temperature intervals of these pick were large. Besides loss of weight was observed to begin at low temperatures in samples irradiated and especially momentary weight loss at some heats in the rang of known temperatures was observed in the coal Slopi contain in bitumen. Because of heat the weight loss in the non irradiated samples forms parabolic curve and because of heat the weight loss in the samples irradiated forms stepped curves. It was shown that the coal irradiated can be easily departed by heat because of the chemical structure in comparison the original one.

  5. JV TASK 45-MERCURY CONTROL TECHNOLOGIES FOR ELECTRIC UTILITIES BURNING LIGNITE COAL, PHASE I BENCH-AND PILOT-SCALE TESTING

    Energy Technology Data Exchange (ETDEWEB)

    John H. Pavlish; Michael J. Holmes; Steven A. Benson; Charlene R. Crocker; Edwin S. Olson; Kevin C. Galbreath; Ye Zhuang; Brandon M. Pavlish

    2003-10-01

    The Energy & Environmental Research Center has completed the first phase of a 3-year, two-phase consortium project to develop and demonstrate mercury control technologies for utilities that burn lignite coal. The overall project goal is to maintain the viability of lignite-based energy production by providing utilities with low-cost options for meeting future mercury regulations. Phase I objectives are to develop a better understanding of mercury interactions with flue gas constituents, test a range of sorbent-based technologies targeted at removing elemental mercury (Hg{sup o}) from flue gases, and demonstrate the effectiveness of the most promising technologies at the pilot scale. The Phase II objectives are to demonstrate and quantify sorbent technology effectiveness, performance, and cost at a sponsor-owned and operated power plant. Phase I results are presented in this report along with a brief overview of the Phase II plans. Bench-scale testing provided information on mercury interactions with flue gas constituents and relative performances of the various sorbents. Activated carbons were prepared from relatively high-sodium lignites by carbonization at 400 C (752 F), followed by steam activation at 750 C (1382 F) and 800 C (1472 F). Luscar char was also steam-activated at these conditions. These lignite-based activated carbons, along with commercially available DARCO FGD and an oxidized calcium silicate, were tested in a thin-film, fixed-bed, bench-scale reactor using a simulated lignitic flue gas consisting of 10 {micro}g/Nm{sup 3} Hg{sup 0}, 6% O{sub 2}, 12% CO{sub 2}, 15% H{sub 2}O, 580 ppm SO{sub 2}, 120 ppm NO, 6 ppm NO{sub 2}, and 1 ppm HCl in N{sub 2}. All of the lignite-based activated (750 C, 1382 F) carbons required a 30-45-minute conditioning period in the simulated lignite flue gas before they exhibited good mercury sorption capacities. The unactivated Luscar char and oxidized calcium silicate were ineffective in capturing mercury. Lignite

  6. Local community opinions regarding the socio-environmental aspects of lignite surface mining: Experiences from central Poland

    International Nuclear Information System (INIS)

    Badera, Jarosław; Kocoń, Paweł

    2014-01-01

    Surface lignite mining covers large areas and usually generates social conflicts which pose one of several energy security threats to certain states. Therefore, defining the social conditions determines the success of a mining project. Two communes were chosen for a public opinion study: Kleszczów, where the Bełchatów mine is located, and Złoczew, where a lignite deposit will soon be developed. The analysis shows, as opposed to other areas in Poland that have been projected for development, that both local communities are characterised by a high level of acceptance for lignite mining. In both cases, awareness about the profits was stronger than anxiety about the investment's negative effects. However, most inhabitants could not assess the mining company's diligence concerning its responsibility for mining damages as well as the diligence of external experts assessing the environmental impacts of excavation. Most respondents also could not assess if the legal regulations of public participation in the decision process were sufficient, but the negative opinions outweighed the positive ones. From the perspective of the energy policy, dialogue-type social communication is needed for every case of a new energy-mining project. Research on local public opinion should be the first step to opening up a social debate. - Highlights: • Lignite mining can generate social conflicts, which may threaten energy security. • Examined communes are characterised by a high level of acceptance for lignite mining. • Inhabitants cannot assess if the legal regulations of mining activity are sufficient. • From the perspective of the energy policy, broader social communication is needed. • Research on the public opinion should be the first step to open up a social debate

  7. Biomass ash-bed material interactions leading to agglomeration in FBC

    DEFF Research Database (Denmark)

    Visser, H.J.M.; van Lith, Simone Cornelia; Kiel, J.H.A.

    2008-01-01

    -scale installations is "coating-induced" agglomeration. During reactor operation, a coating is formed on the surface of bed material grains and at certain critical conditions (e.g., coating thickness or temperature) sintering of the coatings initiates the agglomeration. In an experimental approach, this work...

  8. Lusatian lignite. Decisions for the future; Lausitzer Braunkohle. Entscheidungen fuer die Zukunft

    Energy Technology Data Exchange (ETDEWEB)

    Daehnert, Detlev [Vattenfall Europe Mining AG, Cottbus (Germany); Vattenfall Europe Generation AG und Co. KG, Cottbus (Germany); Ketzmer, Wolfgang [Vattenfall Europe Generation AG und Co. KG, Cottbus (Germany)

    2008-07-15

    During the past months a number of important decisions regarding the future of the Lusatian lignite mining areas have been made or launched. In the focus is the concept of the long-term opencast mine and power plant development. Essential part of the concept is the strategy for meeting future challenges of climate change policy. CCS is the key for it. It is expected, that the CCS technology will be commercially available after 2020. Another important aspect is among others the use of the priority areas of the Welzow-Sued and Nochten opencast mined. The corresponding long-term lignite mining planning procedures were opened in autumn 2007. The plans of the company contain clear and reliable statements regarding the long-term opencast mine development until 2050. However, all decisions the company makes are focussing on putting people and their needs first. Solutions for mining related questions and requirements are jointly developed with the people of the region. Communities in direct neighbourhood to opencast mines are safely protected against immissions by structural and organisational measures. The principles of socially responsible resettlements set the framework of constructive and trustful co-acting of the people concerned and the company very early. The future post-mining landscape offers alternative utilization forms providing employment for many people. Economic development of the region is an important aspect of the company's activities. Under the headline ''Energy region Lusatia'', representatives of Vattenfall, different educational institutions, authorities and the politics have joined forces to formulate a strategic target for the future development of Lusatia. Sustainable development of lignite-based power generation to meet future climate change policy, development of energy industrial know-how and the use of other fuels are important issues. The results are visible. Lignite takes a solid place in the German Energy mix - it

  9. Sorption of heavy metals on lignite impregnated with chitosan

    Czech Academy of Sciences Publication Activity Database

    Havelcová, Martina; Mizera, Jiří; Machovič, V.; Borecká, Lenka; Přibyl, Oldřich; Krausová, Ivana

    2013-01-01

    Roč. 10, č. 1 (2013), s. 105-110 ISSN 1214-9705 R&D Projects: GA ČR(CZ) GBP108/12/G108 Institutional support: RVO:67985891 ; RVO:61389005 Keywords : lignite * chitosan * heavy metals * sorption Subject RIV: DJ - Water Pollution ; Quality Impact factor: 0.667, year: 2013 http://www.irsm.cas.cz/index_en.php?page=acta_detail_doi&id=19

  10. Radon measurements concerning engineering-geological problems in lignite mining

    Energy Technology Data Exchange (ETDEWEB)

    Heinicke, J

    1986-07-01

    Radon measurements have been carried out by the aid of solid-state track detectors at the highwall of a lignite mine in order to forecast the eventual course of a landslide. The measured radon distributions and their changes as a function of time indicated that the slope was geodynamically active, but it was not possible to forecast the rate of sliding.

  11. Briquetting of Tuncbilek lignite fines by using ammonium nitrohumate as a binder

    Energy Technology Data Exchange (ETDEWEB)

    Yildirim, M.; Ozbayoglu, G. [Cukurova University, Adana (Turkey). Mining Engineering Dept.

    2004-03-01

    Results of experiments on the briquetting of Tuncbilek lignite fines using ammonium nitrohumate (anh), a low calorific value, young lignite-derived humic acid salt solution, are reported. The particulate material was blended with ammonium nitrohumate serving as the binder. In the briquetting tests, the effects of moisture content, pressure, binder content, nitrogen content and heat treatment were investigated. Durable briquettes, in terms of mechanical strength and water resistance, were produced with a 7% binder content at 10.5% moisture, following pressing at 1280 kg/cm{sup 2} and drying at 165{sup o}C for 1 h. The briqueues produced with ammonium nitrohumate had better combustion properties than run-of-mine samples; the contribution of the binder to smoke and sulphur emissions was very low and fine dust particles were negligible.

  12. Protecting black ash from the emerald ash borer

    Science.gov (United States)

    Les Benedict

    2010-01-01

    Black ash (Fraxinus nigra) is an important resource for Tribes in the Northeast and Great Lakes regions of the North American continent. Ash in North America is being threatened with widespread destruction as a result of the introduction of emerald ash borer beetle (Agrilus planipennis) in 2002. Measures are being taken to slow the spread of emerald ash borer beetle....

  13. REMOVAL OF TRICHLOROACETIC ACID FROM THE AQUEOUS SOLUTIONS USING NATURAL AND ACTIVATED LIGNITE COALS

    Directory of Open Access Journals (Sweden)

    Hüseyin GÜLENSOY

    1998-02-01

    Full Text Available In these studies, a typical lignite coal found near Istanbul (Yeniköy and its activated products were used to adsorb TCA from aqueous solutions. Particle sizes of coal samples and the concentrations of TCA solutions were chosen as parameters against the fixed amount of adsorbent. The maximum efficiency has been obtained for the coal having (-120 + 150 mesh size fraction activated by heating. As a result, it was shown that these kinds of lignite coals could be used as a good adsorbent. In addition, it was also proved that both the removal and recovery of TCA from some waste waters would easily be possible.

  14. Characterization of dust samples from a coal strip mine using a resuspension chamber

    Directory of Open Access Journals (Sweden)

    Martin Civiš

    2017-06-01

    Full Text Available A metallic cylindrical resuspension chamber (V = 0.437 m3, S = 0.35 m2, S/V = 8.38 was constructed to disperse samples of soil and various kinds of dust. The chamber allows on-line determination of number/mass size distribution of aerosol particles formed by dispersion and subsequent sampling of size-segregated particles on filter media. The samples tested were lignite, power plant flue ash and overburden soil from the Nastup coal strip mine in Northern Bohemia. About 20 mg of the individual samples were pneumatically dispersed by 0.5 liter of pressurized air inside the chamber under defined temperature and humidity conditions. Then the dynamics of aerosol size distributions was recorded using an aerodynamic particle sizer with a frequency of 5 seconds. The lignite and flue ash contributed most to the mass of atmospheric aerosol particles smaller than 10/2.5 micrometer – PM10/ PM2.5. The re-suspended mass of the samples varied between 0.001% for overburden soil and 0.32% for mine road soil. The aerosolized lignite and flue ash samples, sampled by a Harvard Impactor and a Personal Cascade Impactor Sampler, revealed that the ash contained higher amounts of fine particles than the lignite and subsequent chemical analyses, carried out using SEM-EDX, reveals that the PM2.5 fraction formed by dispersion of the ash samples had the highest content of sulphur, and PM10 was dominated by Si. PM10 was closest to mullite, while the PM2.5 fraction contained sulphides, pyrites, pyrrhotites and polytypes of sulphide. The PM1 fraction was dominated by quartz glass. The fractions of sizes 2.5–1 μm and 0.5–0.25 μm were dominated by Si and S, respectively.

  15. Engineering Behavior and Characteristics of Wood Ash and Sugarcane Bagasse Ash

    Directory of Open Access Journals (Sweden)

    Francisco Grau

    2015-10-01

    Full Text Available Biomasses are organic materials that are derived from any living or recently-living structure. Plenty of biomasses are produced nationwide. Biomasses are mostly combusted and usually discarded or disposed of without treatment as biomass ashes, which include wood and sugarcane bagasse ashes. Thus, recycling or treatment of biomass ashes leads to utilizing the natural materials as an economical and environmental alternative. This study is intended to provide an environmental solution for uncontrolled disposal of biomass ashes by way of recycling the biomass ash and replacing the soils in geotechnical engineering projects. Therefore, in this study, characteristic tests of wood and sugarcane bagasse ashes that are considered the most common biomass ashes are conducted. The test of chemical compositions of biomass ashes is conducted using energy dispersive X-ray spectroscopy (EDS, and Scanning Electron Microscope (SEM, and heavy metal analysis is also conducted. Engineering behaviors including hydraulic conductivity, constrained modulus and shear modulus are examined. Also, coal fly ash Class C is used in this study for comparison with biomass ashes, and Ottawa 20/30 sands containing biomass ashes are examined to identify the soil replacement effect of biomass ashes. The results show that the particle sizes of biomass ashes are halfway between coal fly ash Class C and Ottawa 20/30 sand, and biomass ashes consist of a heterogeneous mixture of different particle sizes and shapes. Also, all heavy metal concentrations were found to be below the US Environmental Protection Agency (EPA maximum limit. Hydraulic conductivity values of Ottawa 20/30 sand decrease significantly when replacing them with only 1%–2% of biomass ashes. While both the constrained modulus and shear modulus of biomass ashes are lower than Ottawa 20/30 sand, those of mixtures containing up to 10% biomass ashes are little affected by replacing the soils with biomass ashes.

  16. Possibilities of utilizing the Hungarian reserves of lignite in thermal power stations

    Energy Technology Data Exchange (ETDEWEB)

    Faur, G

    1978-01-01

    The Upper Pannonian lignite reserves subjected to study are suited to opencast mining with respect to their depth and thickness. All of them are characterized by occurrence in multiple beds, the thickness of which however is different per area. The dirt between the strata consists mostly of sand, to a lesser degree of clay or of materials between the former. Continuously operating dredges can be used for working, the types depending on the thickness of the overburden and the technology to be applied. Deep wells with submerged pumps may be employed for drainage. High-capacity mining districts can be operated at the areas subjected to study, new districts must however be opened up to increase the productive capacity beyond a certain limit. Establishment of a significant power station capacity is made possible by the explored lignite reserves. (In Hungarian)

  17. Volatiles and char combustion rates of demineralised lignite and wood blends

    International Nuclear Information System (INIS)

    Yilgin, Melek; Pehlivan, Dursun

    2009-01-01

    Today, much interest is given to the utilisation of materials of plant origin as substitutions of fossil fuels in meeting energy needs to reduce the level of atmospheric pollutant emissions and global warming threat, and emphasis has been placed on the co-combustion of coal and biomass. In this study, volatiles and char combustion behaviour of the fuel pellets composed from demineralised lignite and poplar wood sawdust, were investigated in a cylindrical wire mesh basket placed in a preheated tube furnace. The results have shown that ignition times of the pellets decreased with the burning temperature and shortened further due to demineralisation of lignite. Volatiles combustion rates of the samples did not correlate well with combustion times. However, they can be correlated with their respective proximate volatile matter contents. Char burnout times decreased with increasing combustion rates and correlated well with the respective proximate fixed carbon contents of the samples. Deviations were more considerable in the case of rate data. (author)

  18. The hydrogasification of lignite and sub-bituminous coals

    Science.gov (United States)

    Bhatt, B.; Fallon, P. T.; Steinberg, M.

    1981-02-01

    A North Dakota lignite and a New Mexico sub-bituminous coal have been hydrogenated at up to 900°C and 2500 psi hydrogen pressure. Yields of gaseous hydrocarbons and aromatic liquids have been studied as a function of temperature, pressure, residence time, feed rates and H2/coal ratio. Coal feed rates in excess of 10 lb/hr have been achieved in the 1 in. I. D.×8 ft reactor and methane concentration as high as 55% have been observed. A four-step reaction model was developed for the production and decomposition of the hydrocarbon products. A single object function formulated from the weighted errors for the four dependent process, variables, CH4, C2H6, BTX, and oil yields, was minimized using a program containing three independent iterative techniques. The results of the nonlinear regression analysis for lignite show that a first-order chemical reaction model with respect to C conversion satisfactorily describes the dilute phase hydrogenation. The activation energy for the initial products formation was estimated to be 42,700 cal/gmole and the power of hydrogen partial pressure was found to be +0.14. The overall correlation coefficient was 0.83. The mechanism, the rate expressions, and the design curves developed can be used for scale-up and reactor design.

  19. Reprint of: Production scheduling of a lignite mine under quality and reserves uncertainty

    International Nuclear Information System (INIS)

    Galetakis, Michael; Roumpos, Christos; Alevizos, George; Vamvuka, Despina

    2012-01-01

    The effect of uncertainty sources to the stochastic optimization of the combined project of a new surface lignite mine exploitation and power plant operation for electricity generation is investigated. Major sources of uncertainty that were considered are the reserves and the quality of the lignite. Since probability distribution functions for these uncertainties were estimated during the detailed exploration phase of the deposit, the overall goal is then to determine the optimal capacity of the power plant and consequently the optimal production rate of the mine over the time. The optimization objective that was selected is the maximization of the net present value of the project. Emphasis is placed on the sensitivity analysis for the investigation of the effect of quality and reserves uncertainty on project optimization, on the mathematical formulation of risk attitude strategy and on increasing the efficiency of the optimization process by creating a limited set of feasible solutions applying empirical rules. The developed methodology was applied for the determination of the optimal annual production rate of a new surface lignite mine in the area of Ptolemais–Amynteon in Northern Greece. - Highlights: ► Quality and reserves uncertainty affects considerably the production scheduling. ► Stochastic optimization is greatly accelerated by incorporating Taylor's rule. ► Decisions can be made considering different risk level attitudes.

  20. Co-gasification of a lignite/waste-tyre in a moving bed

    Czech Academy of Sciences Publication Activity Database

    Straka, Pavel; Bučko, Z.

    2009-01-01

    Roč. 90, č. 10 (2009), s. 1202-1206 ISSN 0378-3820 R&D Projects: GA ČR(CZ) GA105/07/1407 Institutional research plan: CEZ:AV0Z30460519 Keywords : co-gasification * waste-tyre * lignite Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.321, year: 2009

  1. Ash Utilisation 2012. Ashes in a Sustainable Society. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-11-01

    Conference themes: Risk assessment, Fly ash- Road construction, Recycling and Greenhouse gases, Storage of ashes, Fertilizer, Metal Mining, Support and Barriers, Construction Material, Civil Engineering, and MSWI bottom ash.

  2. Synfuels from low-rank coals at the Great Plains Gasification Plant

    International Nuclear Information System (INIS)

    Pollock, D.

    1992-01-01

    This presentation focuses on the use of low rank coals to form synfuels. A worldwide abundance of low rank coals exists. Large deposits in the United States are located in Texas and North Dakota. Low rank coal deposits are also found in Europe, India and Australia. Because of the high moisture content of lignite ranging from 30% to 60% or higher, it is usually utilized in mine mouth applications. Lignite is generally very reactive and contains varying amounts of ash and sulfur. Typical uses for lignite are listed. A commercial application using lignite as feedstock to a synfuels plant, Dakota Gasification Company's Great Plains Gasification Plant, is discussed

  3. Large-Scale Mercury Control Technology Testing for Lignite-Fired Utilities - Oxidation Systems for Wet FGD

    Energy Technology Data Exchange (ETDEWEB)

    Steven A. Benson; Michael J. Holmes; Donald P. McCollor; Jill M. Mackenzie; Charlene R. Crocker; Lingbu Kong; Kevin C. Galbreath

    2007-03-31

    Mercury (Hg) control technologies were evaluated at Minnkota Power Cooperative's Milton R. Young (MRY) Station Unit 2, a 450-MW lignite-fired cyclone unit near Center, North Dakota, and TXU Energy's Monticello Steam Electric Station (MoSES) Unit 3, a 793-MW lignite--Powder River Basin (PRB) subbituminous coal-fired unit near Mt. Pleasant, Texas. A cold-side electrostatic precipitator (ESP) and wet flue gas desulfurization (FGD) scrubber are used at MRY and MoSES for controlling particulate and sulfur dioxide (SO{sub 2}) emissions, respectively. Several approaches for significantly and cost-effectively oxidizing elemental mercury (Hg{sup 0}) in lignite combustion flue gases, followed by capture in an ESP and/or FGD scrubber were evaluated. The project team involved in performing the technical aspects of the project included Babcock & Wilcox, the Energy & Environmental Research Center (EERC), the Electric Power Research Institute, and URS Corporation. Calcium bromide (CaBr{sub 2}), calcium chloride (CaCl{sub 2}), magnesium chloride (MgCl{sub 2}), and a proprietary sorbent enhancement additive (SEA), hereafter referred to as SEA2, were added to the lignite feeds to enhance Hg capture in the ESP and/or wet FGD. In addition, powdered activated carbon (PAC) was injected upstream of the ESP at MRY Unit 2. The work involved establishing Hg concentrations and removal rates across existing ESP and FGD units, determining costs associated with a given Hg removal efficiency, quantifying the balance-of-plant impacts of the control technologies, and facilitating technology commercialization. The primary project goal was to achieve ESP-FGD Hg removal efficiencies of {ge}55% at MRY and MoSES for about a month.

  4. Mangrove associated lignite beds of Malvan, Konkan: Evidence for higher sea-level during the Late Tertiary (Neogene) along the west coast of India

    Energy Technology Data Exchange (ETDEWEB)

    Kumaran, K.P.N.; Shindikar, M.; Limaye, R.B. [Agharkar Research Inst., Pune (India)

    2004-01-25

    Fossil pneumatophores (breathing roots) of Avicennia are recovered and reported from the lignite beds exposed in Kolamb well-section near Malvan, Konkan area of western Maharashtra. The accrued palynoflora is dominated by mangroves (Avicennia, Aegialitis, Excoecaria, Rhizophora and Sonneratia). The spores of mangrove fern (Acrostichum aureum) an estuarine fungus Cirrenalia indicate that these lignites are autochthonous and deposited in a near-shore environment. Presence of foraminiferal linings (= microforaminifera), dinoflagellate cysts, a few calcareous nannofossils and scolecodonts is an irrefutable proof of marine and brackish water influence during the deposition of lignites under intertidal/tidal swampy condition (mangrove influenced) with fair input from freshwater swamps and hinterland. Freshwater-related forms, viz. Ceratopteris thalictroides, Nymphaeaceae, Ctenolophonaceae and hinterland taxa (Cullenia/Durio) of Bombacaceae along with abundance of microthyriaceous fungi in the palynoflora imply a warm humid tropical climate with high precipitation during the depositional period. The presence of Ctenolophon englerianus (= Ctenolophonidites costatus) in Kolamb lignites suggests the Late Neogene (Late Miocene-Early Pliocene) age. The occurrence of pneumatophores and associated lignite deposits about 37 m above the present mean sea-level, and much inland, clearly indicates the higher sea-level strand during Late Neogene along the west coast of India.

  5. Water extraction from high moisture lignite by means of efficient integration of waste heat and water recovery technologies with flue gas pre-drying system

    International Nuclear Information System (INIS)

    Han, Xiaoqu; Yan, Junjie; Karellas, Sotirios; Liu, Ming; Kakaras, Emmanuel; Xiao, Feng

    2017-01-01

    Highlights: • Energy-saving potential of FPLPS in different cold-ends and lignite types is evaluated. • Water-saving of FPLPS is realized through recovery of water extracted from lignite. • Integrations of low pressure economizer and spray tower with FPLPS are proposed. • Thermodynamic and economic performances of different schemes are investigated. - Abstract: The flue gas pre-dried lignite-fired power system (FPLPS) integrates the fan mill flue gas dryer with an open pulverizing system and yields an increase of the boiler efficiency. Particularly, the dryer exhaust gas contains a large amount of vapor removed from high moisture lignite, which exhibits great potential for waste heat and water recovery. Two available options are considered to realize the extraction of water from lignite: the low pressure economizer (LPE) for water-cooled units and the spray tower (SPT) integrated with heat pump for air-cooled units. This paper aims at evaluating the energy saving and water recovery potentials of the FPLPS integrated with both schemes. Results showed that the plant efficiency improvement of the FPLPS at base case varied from 1.14% to 1.47% depending on the moisture content of raw lignite. The water recovery ratio and plant efficiency improvement in the optimal LPE scheme were 39.4% and 0.20%, respectively. In contrast, 83.3% of water recover ratio and 110.6 MW_t_h heat supply were achieved in the SPT system. Both schemes were economically feasible with discounted payback periods of around 3 years. Moreover, parametric analysis was conducted to examine the economic viability of both schemes with different lignite types and market factors.

  6. Combustion of mixed fuels (lignite and sewage sludge) in a pilot model of a circulated fluidized bed - a contribution to the waste disposal and to a combustion with low emissions. Final report; Verbrennung von Mischbrennstoffen (Braunkohle und Klaerschlamm) in einer zirkulierenden Wirbelschichtfeuerung - ein Beitrag zur Abfallentsorgung und zu einer schadstoffarmen Verbrennung. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, W.; Brunne, T.; Girndt, H.; Richter, B.; Kaplonek, M.

    1997-04-01

    Mixed fuels based on dried lignite and sewage sludge were burned in a pilot model with circulated fluidized bed technology. The part of sewage sludge has been varied in the fuel, the different reaction and emission conditions were investigated. In the report were laid emphasis on the primary influence of the waste gas components (CO, NO{sub x}, N{sub 2}O). The author started first searchs to the ash composition and to where about of the heavy metals. In the report are recommendation for the industriel effective combustion with low emissions with sewage sludge/lignite mixded fuel. (orig.) [Deutsch] In einer Pilotanlage mit zirkulierender Wirbelschichtfeuerung wurden unterschiedliche Brennstoffgemsiche aus Trockenbraunkohle und Klaerschlamm verbrannt. Die Anteile am Klaerschlamm wurden variiert und die sich aendernden Reaktions- und Emissionsverhaeltnisse aufgenommen. Schwerpunkt dieser Arbeit war die primaere Beeinflussung der Gasschadstoffe (CO, NO{sub x}, N{sub 2}O). Erste Untersuchungen zur Aschenzusammensetzung und zum Verbleib der Schwermetalle wurden vorgenommen. Empfehlungen fuer die grosstechnische, effektive, schadstoffarme Verbrennung von Klaerschlamm/Braunkohle-Gemischen wurden erarbeitet. (orig.)

  7. A realistic EU vision of a lignite-based energy system in transition: Case study of Serbia

    Directory of Open Access Journals (Sweden)

    Batas-Bjelić Ilija

    2015-01-01

    Full Text Available Several Contracting Parties to the Treaty establishing the Energy Community of the South East Europe, currently in energy transition, have electricity production dominantly based on lignite which contrasts their new reality. Planning approach to designing a new feasible energy policy is presented in this paper. This novel approach in using EnergyPLAN tool stems from analysis of market operation of lignite thermal power plants on hourly basis, and quantification of the feasibility of the energy policy and its alignment with EU vision, and is presented in few scenarios. It was found out that the Serbian energy system is highly sensitive to the electricity market and CO2 tax increase, because the marginal costs for lignite generation will increase to more than 50€/MWh. Shifting in the merit order will be observed even at lower CO2 tax levels, because of the intensity of the emission of the electricity sector (calculated to be higher than 700gCO2/kWhel, according to current energy policy. Based on the increased use of renewable energy sources and more efficient energy conversion technologies, socio-economic and energy policy feasibility would be increased, while long-term marginal costs would be improved by 2€/MWh and emission intensity by 258 gCO2/kWhel, compared to the current energy policy. These contributions, shown in the Serbian case, are of general importance for other lignite dominated Contracting Parties to Treaty establishing the Energy Community. [Projekat Ministartsva nauke Republike Srbije, br. 42009

  8. Palynostratigraphy, palynofacies and depositional environment of a lignite-bearing succession at Surkha Mine, Cambay Basin, north-western India

    Directory of Open Access Journals (Sweden)

    Monga Priyanka

    2015-12-01

    Full Text Available The paper reports palynology and palynofacies studies of lignite-bearing sediments exposed in an opencast mine succession at Surkha, Bhavnagar District, in the coastal region of Gujarat, India. The study examined the relationships between the palynoflora, sedimentary organic matter and environment at the time of deposition of lignite and associated sediments. Based on dinoflagellate cyst biostratigraphy, the sedimentary succession is dated as early Eocene (Ypresian. Palynofacies studies helped reveal the palaeoenvironmental fluctuations. The dominance of angiosperm pollen grains, freshwater algae, microthyraceous fungi and a large share of land debris in the lower part of the succession suggests a freshwater swamp environment of deposition for the basal lignite facies. Two cenozones - Matanomadiasulcites maximus and Lakiapollis ovatus - were identified in the lower lignite facies, determined from the dominance of these pollen grains in the palynological assemblages. The presence of angiosperm pollen grains and pteridophyte spores in the carbonaceous shale horizon above the lignite facies indicates a change in the depositional regime from freshwater swamp to lagoonal. This was identified as the Arecipites wodehousei cenozone due to its numerical abundance in the assemblage. Dinoflagellate cyst abundance and diversity, and microforaminiferal test linings along with well-sorted terrestrial debris in the mudstone in the upper part of the succession suggest a more open marine estuarine type of depositional environment. The Homotryblium complex along with Cordospheridium fibrospinosum, Kenleyia sp., and Thalassiphora pelagica dinoflagellate cysts are the main representatives of this zone, determined as the Homotryblium tenuispinosum cenozone. The changing depositional settings (freshwater swamp-lagoonal-estuarine along the vertical succession indicate a marine transgression in this region. Results from palynological studies of early Palaeogene

  9. Australian opencast-lignite mine Yallourn; Der australische Braunkohlentagebau Yallourn

    Energy Technology Data Exchange (ETDEWEB)

    Koscierski, Marcin; Goerlich, Michael [RWTH Aachen (Germany). Inst. fuer Bergbaukunde I

    2009-01-15

    This article is about the open pit lignite mine Yallourn, located 150 km southeast of Melbourne (Figure 1). It focuses on the history, the geology and the environment. Furthermore, it describes the new mining method using large carry dozers. The open pit and the power plant are owned by TruEnergy (part of the CLP Group) and the mining activities are carried out in an Alliance with Roche Thiess Linfox (RTL). (orig.)

  10. A simplified mathematical model for scattered transmission of X-rays in raw brown coal

    International Nuclear Information System (INIS)

    Braune, M.

    1983-01-01

    A simplified mathematical model is presented which renders it possible to calculate the ash content of lignite from scattered transmission of X radiation taking into account two grain classes, the bulk density, and the fill height. The fine grain is assigned to sand and the coarse one to lignite. The model provides a correlation between the fine grain content and the counting rate

  11. Laboratory experiments and analytical investigations on the transfer of organic substances from lignite into ground water and residue lakes during flooding of opencast lignite mines. Final report; Laborexperimente und analytische Untersuchungen ueber den Eintrag braunkohlebuertiger organischer Stoffe in Grundwaesser und Restseegewaesser bei der Flutung von Braunkohletagebauen. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Herzschuh, R.; Frauendorf, H.; Herrmann, D.; Pietzsch, K.

    2000-05-01

    Lignite samples of diffrent lithotypes and composition from opencast mines of Lusatia and the region near Leipzig were submitted to weathering processes in laboratory scale experiments and the transfer of organic matter from lignite into the hydrosphere has been observed. By means of high-performance liquid chromatography/electrospray mass spectrometry used in combination with data from gas chromatography/mass spectrometry numerous lignite-derived aromatic and heteroaromatic (poly-)carboxylic acids as well as aliphatic dicarboxylic acids could be characterized in the aqueous extracts. Investigations on water samples from lignite mining residue lakes cofirm these results. Furthermore, formation of chlororganic compounds like polychlorinated dibenzo-p-dioxine and furans (PCDD/F) and polychlorinated biphenyls (PCB), benzenes (PCBz) and phenols (PCPh) has been investigated on different lignite samples under natural weathering conditions and thermal treatment. (orig.) [German] Braunkohlen verschiedener Lithotypen und Zusammensetzung aus Tagebauen der Lausitz und der Region um Leipzig wurden in Laborexperimenten Verwitterungsprozessen unterzogen und der Uebergang organischer Materie aus der Braunkohle in die Hydrosphaere beobachtet. Mit Hilfe der HPLC-Elektrospray-MS-Untersuchungen in Kombination mit Daten aus GC-MS-Messungen konnten zahlreiche aus der Braunkohle stammende aromatische und heteroaromatische (Poly-)Carbonsaeuren sowie aliphatische Dicarbonsaeuren in den waessrigen Extrakten charakterisiert werden. Untersuchungen an Wasserproben aus bereits gefluteten Tagebaurestseen bestaetigen diese Ergebnisse. Weiterhin wurde die Bildung chlororganischer Verbindungen, wie polychlorierter Dibenzo-p-dioxine und -furane (PCDD/F) sowie polychlorierter Biphenyle (PCB), Benzole (PCBz) und Phenole (PCPh) an unterschiedlichen Braunkohleproben unter natuerlichen Bedingungen und nach thermsicher Behandlung untersucht. (orig.)

  12. Physico-chemistry of adsorption of copper, nickel and cobalt on lignite from ammoniacal solutions

    International Nuclear Information System (INIS)

    Khattak, M.I.

    2004-01-01

    The present paper deals with a process developed for lignite adsorption that can be used to prevent the hard scale formation during distillation of NH/sub 3/ and CO/sub 2/, recover Cu, Ni and Cr from dilute solutions, Cu and NH/sub 3/ from waste effluent containing SO/sub 4/ radicals, separate Cu (NH/sub 3/)/sub 4//sup +2/ and AsO/sub 4//sup -3/ from ammonial solutions and recover Cu, Ni and Co from ore pulps. In additions to the study of the adsorptions of M, NH/sub 3/ and CO/sub 2/ on lignite with caustic soda) was also investigated. Changes of the functional groups of humic acid its salt, before and after the adsorption, were examined by infrared adsorption analysis. (author)

  13. Radioactivity of combustion residues from coal-fired power stations

    International Nuclear Information System (INIS)

    Vom Berg, W.; Puch, K.H.

    1996-01-01

    Each year in Germany, about 18 mill. t of combustion residues are produced from the combustion of bituminous coal and lignite. They are utilized to a great extent in the construction industry and in mining. During the combustion of coal, the radio-nuclides remain predominantly in the ash. The radionuclide concentration in lignite ash is within the range of that in natural soil. The combustion residues of bituminous coal contain radio-nuclides of a similar order of magnitude as also can occur in natural rock. The utilization of combustion residues in construction materials makes a negligible contribution to radiation exposure through retention in buildings. (orig.) [de

  14. Biomass ash utilization

    Energy Technology Data Exchange (ETDEWEB)

    Bristol, D.R.; Noel, D.J.; O`Brien, B. [HYDRA-CO Operations, Inc., Syracuse, NY (United States); Parker, B. [US Energy Corp., Fort Fairfield, ME (United States)

    1993-12-31

    This paper demonstrates that with careful analysis of ash from multiple biomass and waste wood fired power plants that most of the ash can serve a useful purpose. Some applications require higher levels of consistency than others. Examples of ash spreading for agricultural purposes as a lime supplement for soil enhancement in Maine and North Carolina, as well as a roadbase material in Maine are discussed. Use of ash as a horticultural additive is explored, as well as in composting as a filtering media and as cover material for landfills. The ash utilization is evaluated in a framework of environmental responsibility, regulations, handling and cost. Depending on the chemical and physical properties of the biomass derived fly ash and bottom ash, it can be used in one or more applications. Developing a program that utilizes ash produced in biomass facilities is environmentally and socially sound and can be financially attractive.

  15. Development of novel ash hybrids to introgress resistance to emerald ash borer into north American ash species

    Science.gov (United States)

    Jennifer L. Koch; David W. Carey; Mary E. Mason

    2008-01-01

    Currently, there is no evidence that any of the native North American ash species have any resistance to the emerald ash borer (EAB). This means that the entire ash resource of the eastern United States and Canada is at risk of loss due to EAB. In contrast, outbreaks of EAB in Asian ash species are rare and appear to be isolated responses to stress (Bauer et al. 2005,...

  16. Lignite and tin ores exploration in southern part of Thailand by using nuclear track-etch detectors

    International Nuclear Information System (INIS)

    Chittrakarn, T.; Boonnummar, R.; Pongsuwan, T.; Nuannin, P.; Kaew-On, C.

    1993-01-01

    Both lignite and tin mines in Southern of Thailand are associated with uranium ore. In lignite exploration, Bangpudum Lignite Mine at Krabi Province was chosen for this studied because we know the exact location and deposition of coal seam by using other geophysical technique and also confirm by borehole. The size 1x2 cm 2 of cellulose nitrate CN-85 films were used, each film was stuck at the inner bottom of a softdrink cup. Each cup was put up side down at the bottom of a borehole about 75 cm depth from the earth surface and laid about 10 m apart. All the cups were put in the hole along the line in order to cover about 280 metre in the cross sectional direction long of the known coal seam. After one month, all the film detectors were collected and etched with 6.25N NaOH at 60 o C about 25 minutes long in order to enlarge the latent alpha registration tracks. These alpha particles were emitted from radon gas (Rn-222) which was generated from uranium associated with lignite ore. The registration track density per area of each CN-85 film was studied by optical microscope at 400x magnifications. We found that the track densities of the films have high correlation with the depth of the known coal seam while high and low track densities will correspond to the shallow and deep coal seam respectively. Also, track density was significantly higher than background. A similar manner of experiment was designed for tin ore exploration at Ronpibul district, Nakorn Si Thammarat province. The result is in progress and will present at the conference. (Author)

  17. Effect of co-combustion on the burnout of lignite/biomass blends: a Turkish case study.

    Science.gov (United States)

    Haykiri-Acma, H; Yaman, S

    2008-11-01

    Co-combustion of Turkish Elbistan lignite and woody shells of hazelnut was performed in a TGA up to 1173 K with a heating rate of 20 K/min. SEM images of each fuel revealed the differences in their physical appearances. Hazelnut shell was blended with lignite in the range of 2-20 wt% to observe the co-combustion properties. Maximum burning rates (Rmax), temperatures of the maximum burning rates (T(R-max)), and the final burnout values of the parent samples and the blends were compared. The results were interpreted considering lignite properties and the major biomass ingredients such as cellulosics, hemicellulosics, and lignin. Deviations between the theoretical and experimental burnout values were evaluated at various temperatures. Burnout characteristics of the blends up to 10 wt% were concluded to have a synergistic effect so the addition of hazelnut shell up to 8 wt% provided higher burnouts than the expected theoretical ones, whereas addition of as much as 10 wt% led to a decrease in the burnout. However, the additive effects were more favorable for the blend having a biomass content of 20 wt%. Apparent activation energy, Rmax, and T(R-max), were found to follow the additive behavior for the blend samples.

  18. Effect of co-combustion on the burnout of lignite/biomass blends: A Turkish case study

    Energy Technology Data Exchange (ETDEWEB)

    Haykirl-Acma, H.; Yaman, S. [Istanbul Technical University, Istanbul (Turkey)

    2008-11-15

    Co-combustion of Turkish Elbistan lignite and woody shells of hazelnut was performed in a TGA tip to 1173 K with a heating rate of 20 K/min. SEM images of each fuel revealed the differences in their physical appearances. Hazelnut shell was blended with lignite in the range of 2-20 wt% to observe the co-combustion properties. Maximum burning rates (R{sub max}), temperatures of the maximum burning rates (TR{sub max}), and the final burnout values of the parent samples and the blends were compared. The results were interpreted considering lignite properties and the major biomass ingredients such as cellulosics, hemicellulosics, and lignin. Deviations between the theoretical and experimental burnout values were evaluated at various temperatures. Burnout characteristics of the blends up to 10 wt% were concluded to have a synergistic effect so the addition of hazelnut shell up to 8 wt% provided higher burnouts than the expected theoretical ones, whereas addition of as much as 10 wt% led to a decrease in the burnout. However, the additive effects were more favorable for the blend having a biomass content of 20 wt%. Apparent activation energy, R{sub max} and TR{sub max}, were found to follow the additive behavior for the blend samples.

  19. NEW DATA ON THE LOWER PLEISTOCENE (GELASIAN LIGNITE BEDS OF CASTEL SAN PIETRO (RIETI, CENTRAL ITALY

    Directory of Open Access Journals (Sweden)

    LUCA PANDOLFI

    2017-04-01

    Full Text Available A multiproxy study of the lignite-bearing lacustrine sequence cropping out at Castel San Pietro (CSP (Rieti, central Italy provides new insights on the paleoenvironmental evolution of an extensional basin, located on the Tyrrhenian side of the Apennine range. The CSP fossiliferous levels reflect deposition in a stable lacustrine environment. Mammal remains collected from this locality during the past centuries include Stephanorhinus etruscus, Anancus arvernensis and the beaver Castor fiber. The co-existence of the Etruscan rhinoceros and the mastodont suggests a middle Villafranchian age (Montopoli or Coste San Giacomo Faunal Unit for the lignite beds of CSP. New paleoflora findings are in agreement with an attribution to the Piacenzian or Gelasian age for these deposits whilst the presence of the ostracod Qinghaicypris cf. Q. riojensis suggests a time interval from Zanclean to Gelasian (between ~4.5 and ~1.8 Ma. Accordingly, the lignite beds of CSP most likely were deposited during the Gelasian (from ca. 2.5 to 1.8 Ma; from Montopoli to Coste San Giacomo FUs or possibly to Olivola FU in forested area and warm and humid conditions.

  20. The German lignite industry. Historical development, resources, technology, economic structures and environmental impact. Study; Die deutsche Braunkohlenwirtschaft. Historische Entwicklungen, Ressourcen, Technik, wirtschaftliche Strukturen und Umweltauswirkungen. Studie

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2017-05-15

    Lignite has a key role to play in the transformation of the energy system due to its specific structural features in terms of industry, company history, policy, economics, the environment and regional structures. Understanding these structural features of the German lignite industry is an important requirement for classifying the significance of the lignite industry up to now and for the redesigning of this industrial sector. From these environmental, economic and regulatory structural characteristics, which are interwoven in a variety of ways, the incentives arise for the mining and power plant operators to react to energy price signals or energy policy steering. The aim of this research study is to define these structural features, to compile comprehensively the basic data and information that is not always transparently available, to understand the interactions, to enable the navigation of issues that are partly very complex, and to classify into the long-term developments that are especially important for political and social processes. In 2016 approx. 12 percent of German primary energy consumption was met using lignite. At the same time, lignite has the highest carbon dioxide (CO2) emissions of the fossil fuels; it currently accounts for approx. 19 percent of Germany's total greenhouse gas emissions as well as approx. 46 percent of the total CO2 emissions of the electricity sector. As a result of the mining of lignite and its conversion into electricity, substantial adverse impacts beyond the entry of greenhouse gases into the Earth's atmosphere arise for other environmental media. These impacts include half of Germany's mercury emissions, approx. a third of its sulfur dioxide emissions and approx. a tenth of its nitrogen oxide emissions. Lignite mining in open-cast mines takes up a substantial amount of landscape and soil and requires huge interventions in the water balance. Relatively high costs arise for the recultivation and rehabilitation

  1. Silica from Ash

    Indian Academy of Sciences (India)

    management, polymer composites and chemical process design. Figure 1 Difference in color of the ash ... The selection of ash is important as the quality of ash determines the total amount as well as quality of silica recoverable Ash which has undergone maximum extent of combustion is highly desirable as it contains ...

  2. The Mineral Character and Geomechanical Properties of the Transitional Rocks from the Mesozoic-Neogene Contact Zone in the Bełchatów Lignite Deposit

    OpenAIRE

    Agnieszka Pękala

    2014-01-01

    Purpose: Beginning more than 30 years ago, opencast lignite mining in the "Bełchatów" area is an important source of accompanying minerals. Lignite mining in the "Bełchatów" mine yields, on average, more than 35 million tonnes per annum and requires removing more than 110 million cubic meters of overburden. Therefore the mine outside of the main mineral exploitation of lignite, leads to a large-scale economy of accompanying minerals. Part of the minerals are present in the overburden and are ...

  3. Comparative palynology of clastics and lignites from the Manning Formation, Jackson Group, Upper Eocene, Grimes County, TX

    Energy Technology Data Exchange (ETDEWEB)

    Gennett, J.A. [Texas A& M Univ., College Station, TX (United States)

    1996-09-01

    The 3500 lignite seam at the Gibbons Creek Mine in Grimes County, TX was sampled for pollen and spores at 10 cm intervals. The majority of samples are dominated (to 60%) by Momipites from the Juglandaceae (walnut family), as is typical of Jackson Group sediments. Other palynomorph taxa vary systematically, with a peak of pollen of the freshwater tree Nyssa (blackgum) and associated Rboipites angustus (to 17%) occurring at the base. Higher in the seam, increase (to 55%) of Cupuliferoipollenites (a chestnut-like grain) and Cyrillaceae-pollenites? ventosus (to 7%) percentages may indicate a higher salinity environment. A Chrysophyllum (satin leaf) peak (to 25%) near the top of the seam suggests relatively shallow fresh-water conditions. Core samples from an interval above the lignites represent a transgressive-regressive cycle in inner shelf clastics. These samples were taken at 40 cm or greater intervals and reveal the regional pollen flora. Although minor changes occur, palynomorph spectra are for the most part homogenous. The dominant grain is again Momipites coryloides, but in general percentages are lower (to 35%). Cupuliferoipollenites (to 17%), Chrysophyllum (to 5%), and Rhoipites angustus (to 3%) are not less important, but do not peak as they do in the lignite spectra. Palm leaf megafossils; in one sample suggest a clastic wetland; in this sample palm pollen (mostly Arecipites, representing the modern saw palmetto) reaches 73%. Another sample contains high (26%) percentages of the fern spore Lygodiumsporites adriennis. High percentages of these two taxa do not occur in the lignite samples.

  4. False deformation temperatures for ash fusibility associated with the conditions for ash preparation

    Energy Technology Data Exchange (ETDEWEB)

    Wall, T.F.; Gupta, S.K.; Gupta, R.P.; Sanders, R.H.; Creelman, R.A.; Bryant, G.W. [University of Newcastle, Callaghan, NSW (Australia). Cooperative Research Centre for Black Coal Utilization, Dept. of Chemical Engineering

    1999-07-01

    A study was made to investigate the fusibility behaviour of coal ashes of high ash fusion temperatures. Coals and ashes formed in the boiler were sampled in several Australian power stations, with laboratory ashes being prepared from the coals. The laboratory ashes gave lower values for the deformation temperature (DT) than the combustion ashes when the ash had low levels of basic oxide components. Thermo-mechanical analysis, quantitative X-ray diffraction and scanning electron microscopy were used to establish the mechanisms responsible for the difference. Laboratory ash is finer than combustion ash and it includes unreacted minerals (such as quartz, kaolinite and illite) and anhydrite (CaSO{sub 4}). Fusion events which appear to be characteristic of reacting illite, at temperatures from 900 to 1200{degree}C, were observed for the laboratory ashes, these being associated with the formation of melt phase and substantial shrinkage. The combustion ashes did not contain this mineral and their fusion events were observed at temperatures exceeding 1300{degree}C. The low DTs of coal ashes with low levels of basic oxides are therefore a characteristic of laboratory ash rather than that found in practical combustion systems. These low temperatures are not expected to be associated with slagging in pulverised coal fired systems. 10 refs., 3 figs., 2 tabs.

  5. Biowaste utilization in the process of co-gasification with bituminous coal and lignite

    International Nuclear Information System (INIS)

    Howaniec, Natalia; Smoliński, Adam

    2017-01-01

    Biowaste utilization in co-gasification with bituminous coal and lignite gives the benefits of stable supplies of a primary energy source – coal and utilization of a zero-emission, waste material (i.e. agriculture waste, sewage sludge, etc.) with higher process efficiency and lower negative environmental impact than biomass or coal gasification, respectively. The main focus of the study presented is co-gasification of bituminous coal or lignite with biowaste to hydrogen-rich gas. The experiments were performed in the laboratory scale fixed-bed reactor installation at 700 and 900 °C. The Hierarchical Clustering Analysis complemented with a color map of studied data were applied in the selection of the optimal operating parameters for biowaste utilization in the co-gasification process based on the experimental data of gasification/co-gasification process as well as physical and chemical properties of fuels tested. The experimental results showed that the carbon conversion rate in co-gasification increased with increasing biomass content in a fuel. The total gas volume and hydrogen volume in co-gasification were higher than the values expected based on the results of the gasification process of the fuels analyzed. - Highlights: • Biowaste co-gasification with bituminous coal/lignite to hydrogen-rich gas. • Steam co-gasification in laboratory scale fixed-bed reactor at 700 and 900 °C. • Hierarchical Clustering Analysis complemented with color map of experimental data. • Carbon conversion increase with increasing biomass content. • The highest total gas and hydrogen volume in co-gasification of C-B20 blend at 900C.

  6. Cementing Efficiency of Low Calcium Fly Ash in Fly Ash Concretes

    OpenAIRE

    T. D. Gunneswara Rao; Mudimby Andal

    2014-01-01

    Research on the utilization of fly ash will no longer refer the fly ash as a waste material of thermal power plants. Use of fly ash in concrete making, makes the concrete economical as well as durable. The fly ash is being added to the concrete in three ways namely, as partial replacement to cement, as partial replacement to fine aggregates and as admixture. Addition of fly ash to the concrete in any one of the form mentioned above, makes the concrete more workable and durable than the conven...

  7. Emerald ash borer biocontrol in ash saplings: the potential for early stage recovery of North American ash

    Science.gov (United States)

    In many parts of North America, ash stands have been reduced by the emerald ash borer (Agrilus planipennis) invasion to a few surviving mature trees and young basal sprouts, saplings, and seedlings. Without a seed bank, ash tree recovery will require survival and maturation of these younger cohorts...

  8. Radioactivity of wood ash

    International Nuclear Information System (INIS)

    Rantavaara, A.; Moring, M.

    2000-01-01

    STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg -1 , in decreasing order: 137 Cs, 40 K, 90 Sr, 210 Pb, 226 Ra, 232 Th, 134 Cs, 235 U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and 210 Pb was hardly detectable. The NH 4 Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

  9. Estimation of spatial variability of lignite mine dumping ground soil properties using CPTu results

    Directory of Open Access Journals (Sweden)

    Bagińska Irena

    2016-03-01

    Full Text Available The paper deals with application of CPTu test results for the probabilistic modeling of dumping grounds. The statistical measures use results from 42 CPT test points located in the lignite mine dumping ground from the region of Central Europe. Both the tip resistance qc as well as local friction fs are tested. Based on the mean values and standard deviations of measured quantities the specific zones in the dumping site profile are distinguished. For three main zones standard deviations of linearly de-trended functions, distributions of normalized de-trended values for qc and fs are examined. Also the vertical scales of fluctuation for both measured quantities are estimated. The obtained result shows that lignite mine dumping site can be successfully described with the Random Field Theory. Additional use of fs values introduces supplementary statistical information.

  10. Perspectives on the German lignite industry in 2012. Stability through diversity; Perspektiven der deutschen Braunkohlenindustrie 2012. Stabilitaet durch Vielfalt

    Energy Technology Data Exchange (ETDEWEB)

    Lambertz, Johannes F. [RWE Power AG, Koeln (Germany); Milojcic, George [Bundesverband Braunkohle (DEBRIV), Koeln (Germany)

    2012-07-15

    The formula - stability through diversity - stands for a promising approach to energy policy. Germany will be phasing out nuclear energy by 2022 and giving a big push to renewables as a substitute. That changes the electricity mix. In this setting, lignite becomes more valuable as base load energy. Any look at the history of technology shows that, in the competition to find good solutions, experience proves that diversity is generated, and that means stability. In the energy sector, no one solution will determine the future, but many different technologies will co-exist in a pattern that is increasingly networked and integrated. The background here is a combination of nature circumstances, the wishes of consumers and, of course, the technical potential and availability of raw materials. There is no sign that coal, which is so abundantly available and competitive worldwide, will be excluded from the energy mix any time soon. The figures prove the contrary. The dynamism of world coal consumption speaks an unequivocal language. Germany, with its lignite, has a valuable natural resource which will be available for a long time to come. Germany's energy-policy aim should be to make use of the strengths of domestic lignite, strengths like security of supply and affordability, while working on minimising CO{sub 2} emissions, in particular through increases in efficiency and, in the long run, through CCS. Indispensable for this are the underlying production conditions. At the start, I had a word of thanks for our many partners for their good cooperation. We go on relying on your support. Specifically, we hope that the lignite industry, like other sectors will go on being appreciated for the benefits that it brings, and that no additional burdens are envisaged that might impair its competitiveness. It is our task in the lignite industry to further develop the potential of lignite with our wealth of ideas and fact-driven work. The good of today thus make a better

  11. Exergy Analysis of Operating Lignite Fired Thermal Power Plant

    Directory of Open Access Journals (Sweden)

    K. Murugesan

    2009-01-01

    Full Text Available The energy assessment must be made through the energy quantity as well as the quality. But the usual energy analysisevaluates the energy generally on its quantity only. However, the exergy analysis assesses the energy on quantity as well asthe quality. The aim of the exergy analysis is to identify the magnitudes and the locations of real energy losses, in order toimprove the existing systems, processes or components. The present paper deals with an exergy analysis performed on anoperating 50MWe unit of lignite fired steam power plant at Thermal Power Station-I, Neyveli Lignite Corporation Limited,Neyveli, Tamil Nadu, India. The exergy losses occurred in the various subsystems of the plant and their components havebeen calculated using the mass, energy and exergy balance equations. The distribution of the exergy losses in several plantcomponents during the real time plant running conditions has been assessed to locate the process irreversibility. The Firstlaw efficiency (energy efficiency and the Second law efficiency (exergy efficiency of the plant have also been calculated.The comparison between the energy losses and the exergy losses of the individual components of the plant shows that themaximum energy losses of 39% occur in the condenser, whereas the maximum exergy losses of 42.73% occur in the combustor.The real losses of energy which has a scope for the improvement are given as maximum exergy losses that occurredin the combustor.

  12. Production of fuels out of lignite and lignocelluloses; Herstellung von Brennstoffen aus Braunkohle und Lignozellulose

    Energy Technology Data Exchange (ETDEWEB)

    Naundorf, W.; Schroeder, H.W.; Trommer, D. [TU Bergakademie Freiberg (Germany)

    2001-12-01

    The acceptance towards solid fuels will increase again if its ease of use is improved, the production costs remain low for extended periods of time, and high thermal efficiencies as well as low pollutant emissions are achieved. These demands can only be met by optimal fuel processing and the use of modern fuel engineering which applies, if possible, continuous and controlled fuel and air feed technology. Two fuels are introduced which are produced out of lignite and lignocelluloses by compaction or by balling granulation. Considering the improvement of combustion properties, remarkable synergy effects occur due to this raw material combination. Lignocelluloses act as an ignition auxillary. Lignite functions as a binding agent, increases the fuels' fire resistance, and guarantees a long, sustained combustion with an excellent combustion rate. (orig.)

  13. Condition-Based Conveyor Belt Replacement Strategy in Lignite Mines with Random Belt Deterioration

    Science.gov (United States)

    Blazej, Ryszard; Jurdziak, Leszek

    2017-12-01

    In Polish lignite surface mines, condition-based belt replacement strategies are applied in order to assure profitable refurbishment of worn out belts performed by external firms specializing in belt maintenance. In two of three lignite mines, staff asses belt condition subjectively during visual inspections. Only one mine applies specialized diagnostic device (HRDS) allowing objective magnetic evaluation of belt core condition in order to choose the most profitable moment for the dismantling of worn out belt segments from conveyors and sending them to the maintenance firm which provides their refurbishment. This article describes the advantages of a new diagnostic device called DiagBelt. It was developed at the Faculty of Geoengineering, Mining and Geology, Wroclaw University of Science and Technology. Economic gains from its application are calculated for the lignite mine and for the belt maintenance firm, taking into account random life (durability) of new and reconditioned belts (after the 1st and the 2nd refurbishment). Recursive calculations for following years allow the estimation of the length and costs of replaced, reconditioned and purchased belts on an annual basis, while the use of the Monte Carlo method allows the estimation of their variability caused by random deterioration of belts. Savings are obtained due to better selection of moments (times) for the replacement of belt segments and die to the possibility to qualify worn out belts for refurbishment without the need to remove their covers. In effect, increased belt durability and lowered share of waste belts (which were not qualified for reconditioning) create savings which can quickly cover expenditures on new diagnostic tools and regular belt inspections in the mine.

  14. Fly ash carbon passivation

    Science.gov (United States)

    La Count, Robert B; Baltrus, John P; Kern, Douglas G

    2013-05-14

    A thermal method to passivate the carbon and/or other components in fly ash significantly decreases adsorption. The passivated carbon remains in the fly ash. Heating the fly ash to about 500 and 800 degrees C. under inert gas conditions sharply decreases the amount of surfactant adsorbed by the fly ash recovered after thermal treatment despite the fact that the carbon content remains in the fly ash. Using oxygen and inert gas mixtures, the present invention shows that a thermal treatment to about 500 degrees C. also sharply decreases the surfactant adsorption of the recovered fly ash even though most of the carbon remains intact. Also, thermal treatment to about 800 degrees C. under these same oxidative conditions shows a sharp decrease in surfactant adsorption of the recovered fly ash due to the fact that the carbon has been removed. This experiment simulates the various "carbon burnout" methods and is not a claim in this method. The present invention provides a thermal method of deactivating high carbon fly ash toward adsorption of AEAs while retaining the fly ash carbon. The fly ash can be used, for example, as a partial Portland cement replacement in air-entrained concrete, in conductive and other concretes, and for other applications.

  15. Ashes to ashes: Large Fraxinus germplasm collections and their fates

    Science.gov (United States)

    Kim C. Steiner; Paul. Lupo

    2010-01-01

    As the emerald ash borer (EAB) threatens the survival of our ash species, measures should be taken to preserve their genetic variability in the event that we discover a way to restore populations destroyed by the beetle. As it happens, large germplasm collections exist for our most important and widely distributed eastern species of the genus, white ash (...

  16. Mapping of coal quality using stochastic simulation and isometric logratio transformation with an application to a Texas lignite

    Science.gov (United States)

    Olea, Ricardo A.; Luppens, James A.

    2015-01-01

    Coal is a chemically complex commodity that often contains most of the natural elements in the periodic table. Coal constituents are conventionally grouped into four components (proximate analysis): fixed carbon, ash, inherent moisture, and volatile matter. These four parts, customarily measured as weight losses and expressed as percentages, share all properties and statistical challenges of compositional data. Consequently, adequate modeling should be done in terms of a logratio transformation, a requirement that is commonly overlooked by modelers. The transformation of choice is the isometric logratio transformation because of its geometrical and statistical advantages. The modeling is done through a series of realizations prepared by applying sequential simulation for the purpose of displaying the parts in maps incorporating uncertainty. The approach makes realistic assumptions and the results honor the data and basic considerations, such as percentages between 0 and 100, all four parts adding to 100% at any location in the study area, and a style of spatial fluctuation in the realizations equal to that of the data. The realizations are used to prepare different results, including probability distributions across a deposit, E-type maps displaying average properties, and probability maps summarizing joint fluctuations of several parts. Application of these maps to a lignite bed clearly delineates the deposit boundary, reveals a channel cutting across, and shows that the most favorable coal quality is to the north and deteriorates toward the southeast.

  17. Fusion characterization of biomass ash

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Teng [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Sino-Danish Center for Education and Research, Beijing, 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Fan, Chuigang; Hao, Lifang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Li, Songgeng, E-mail: sgli@ipe.ac.cn [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Song, Wenli [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Lin, Weigang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Department of Chemical and Biochemical Engineering, Technical University of Denmark, 2800 Kgs. Lyngby (Denmark)

    2016-08-20

    Highlights: • A novel method is proposed to analyze fusion characteristics of biomass ash. • T{sub m} can represent the severe melting temperature of biomass ash. • Compared with AFT, TMA is the better choice to analyze the fusion characteristics of biomass ash. - Abstract: The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, T{sub m}, is proposed to represent the severe melting temperature of biomass ash. The fusion characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates.

  18. Trace elements in coal ash

    Science.gov (United States)

    Deonarine, Amrika; Kolker, Allan; Doughten, Michael W.

    2015-01-01

    Coal ash is a residual waste product primarily produced by coal combustion for electric power generation. Coal ash includes fly ash, bottom ash, and flue-gas desulfurization products (at powerplants equipped with flue-gas desulfurization systems). Fly ash, the most common form of coal ash, is used in a range of products, especially construction materials. A new Environmental Protection Agency ruling upholds designation of coal ash as a non-hazardous waste under Subtitle D of the Resource Conservation and Recovery Act, allowing for the continued beneficial use of coal ash and also designating procedures and requirements for its storage.

  19. Mercury release from fly ashes and hydrated fly ash cement pastes

    Science.gov (United States)

    Du, Wen; Zhang, Chao-yang; Kong, Xiang-ming; Zhuo, Yu-qun; Zhu, Zhen-wu

    2018-04-01

    The large-scale usage of fly ash in cement and concrete introduces mercury (Hg) into concrete structures and a risk of secondary emission of Hg from the structures during long-term service was evaluated. Three fly ashes were collected from coal-fired power plants and three blend cements were prepared by mixing Ordinary Portland cement (OPC) with the same amount of fly ash. The releasing behaviors of Hg0 from the fly ash and the powdered hydrated cement pastes (HCP) were measured by a self-developed Hg measurement system, where an air-blowing part and Hg collection part were involved. The Hg release of fly ashes at room temperature varied from 25.84 to 39.69 ng/g fly ash during 90-days period of air-blowing experiment. In contrast, the Hg release of the HCPs were in a range of 8.51-18.48 ng/g HCP. It is found that the Hg release ratios of HCPs were almost the same as those of the pure fly ashes, suggesting that the hydration products of the HCP have little immobilization effect on Hg0. Increasing temperature and moisture content markedly promote the Hg release.

  20. Refining of raw materials, lignite present economic problems

    Energy Technology Data Exchange (ETDEWEB)

    Schirmer, G.

    1985-06-01

    East Germany seeks an economic intensification program that involves refining raw materials to a higher level. Lignite briquetting prior to liquefaction and gasification illustrates both the theoretical and practical aspects of that goal and also introduces questions of secure supplies. The author describes the special labor processes, use of technology, recycling of waste materials, and other new problems that the approach entails as the refined raw materials become new materials or energy sources. Economics based on the value of the refined product and the cost of the materials determine the degree of refinement. The concept also involves the relationship of producer and user as profits increase.

  1. Fly ash aggregates. Vliegaskunstgrind

    Energy Technology Data Exchange (ETDEWEB)

    1983-03-01

    A study has been carried out into artificial aggregates made from fly ash, 'fly ash aggregates'. Attention has been drawn to the production of fly ash aggregates in the Netherlands as a way to obviate the need of disposal of fly ash. Typical process steps for the manufacturing of fly ash aggregates are the agglomeration and the bonding of fly ash particles. Agglomeration techniques are subdivided into agitation and compaction, bonding methods into sintering, hydrothermal and 'cold' bonding. In sintering no bonding agent is used. The fly ash particles are more or less welded together. Sintering in general is performed at a temperature higher than 900 deg C. In hydrothermal processes lime reacts with fly ash to a crystalline hydrate at temperatures between 100 and 250 deg C at saturated steam pressure. As a lime source not only lime as such, but also portland cement can be used. Cold bonding processes rely on reaction of fly ash with lime or cement at temperatures between 0 and 100 deg C. The pozzolanic properties of fly ash are used. Where cement is applied, this bonding agent itself contributes also to the strength development of the artificial aggregate. Besides the use of lime and cement, several processes are known which make use of lime containing wastes such as spray dry absorption desulfurization residues or fluid bed coal combustion residues. (In Dutch)

  2. Hydration of fly ash cement and microstructure of fly ash cement pastes

    Energy Technology Data Exchange (ETDEWEB)

    Shiyuan, H.

    1981-01-01

    The strength development and hydration of fly ash cement and the influence of addition of gypsum on those were studied at normal and elevated temperatures. It was found that an addition of a proper amount of gypsum to fly ash cement could accelerate the pozzolanic reaction between CH and fly ash, and as a result, increase the strength of fly ash cement pastes after 28 days.

  3. The Effect of Applied Organic Fertilizers on the Bioavailability of Heavy Metals in Lolium Perenne, Cultivated on Fly Ash Deposits

    Directory of Open Access Journals (Sweden)

    Smaranda Mâşu

    2011-10-01

    Full Text Available The study aims to monitor the capacity of certain organic fertilizers (volcanic tuff and municipal sludge, applied as such and mixed with volcanic rocks with a high content in clinoptilolite, to determine the covering with vegetation of fly ash deposits resulted from the combustion of lignite in thermal plants. Both biosolids (20 t/ha and volcanic rock with high clinoptilolite content (5 t/ha determined the installation of a vegetative layer and diminished the soil metal bioavailability to the Lolium prerenne plant biomass. When using the organic-zeolite mixture, a synergistic effect is recorded of the two components of the treatment agent and an increase of the biomass with 448%. Moreover, the resulted biomass shows the highest reductions of metal bioaccumulations, of 38-46% for Zn and Fe, of 62% for Cu and between 82-89% for Cr, Ni and Pb.

  4. Glass-ceramic from mixtures of bottom ash and fly ash.

    Science.gov (United States)

    Vu, Dinh Hieu; Wang, Kuen-Sheng; Chen, Jung-Hsing; Nam, Bui Xuan; Bac, Bui Hoang

    2012-12-01

    Along with the gradually increasing yield of the residues, appropriate management and treatment of the residues have become an urgent environmental protection problem. This work investigated the preparation of a glass-ceramic from a mixture of bottom ash and fly ash by petrurgic method. The nucleation and crystallization kinetics of the new glass-ceramic can be obtained by melting the mixture of 80% bottom ash and 20% fly ash at 950 °C, which was then cooled in the furnace for 1h. Major minerals forming in the glass-ceramics mainly are gehlenite (Ca(2)Al(2)SiO(7)) & akermanite (Ca(2)MgSiO(7)) and wollastonite (CaSiO(3)). In addition, regarding chemical/mechanical properties, the chemical resistance showing durability, and the leaching concentration of heavy metals confirmed the possibility of engineering and construction applications of the most superior glass-ceramic product. Finally, petrurgic method of a mixture of bottom ash and fly ash at 950 °C represents a simple, inexpensive, and energy saving method compared with the conventional heat treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. Process for treating bituminous coal, lignite, peat, and shale, and products obtained

    Energy Technology Data Exchange (ETDEWEB)

    Schabelitz, E J

    1951-06-27

    A process is described comprising leaching bituminous coal, lignite, peat, or shale by immersing said material in ethylene dichloride for a period of time sufficient to remove the ethylene dichloride-soluble constituents, separating the treated material from the ethylene dichloride solution and recovering from the solution the soluble constituents of the material dissolved in the solution. Soluble constituents include oils and waxes.

  6. Development of a new methodology for mitigating acid mine drainage (AMD) at reclaimed surface mines

    International Nuclear Information System (INIS)

    Ackman, T.E.; Kim, A.G.

    1993-01-01

    A 1.2 hectare (ha) experimental site located on a 14.5 ha reclaimed surface mine in Greene County, PA was injected with a 141 cubic meters (m 3 ) of fly ash and fluidized bed combustion (FBC) ash grout that included acid mine drainage (AMD) sludge. An evaluation of this AMD abatement approach by the Bureau of Mines found that the average net acidity and concentrations of several metal ions at the discharge seep and monitoring wells decreased after grouting. Changes in metal concentrations were assumed to be related to alkaline addition and/or encapsulation. Initial results indicate that this technique is potentially an effective AMD abatement method

  7. Fusion characterization of biomass ash

    DEFF Research Database (Denmark)

    Ma, Teng; Fan, Chuigang; Hao, Lifang

    2016-01-01

    The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two...... stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, Tm, is proposed to represent the severe melting temperature of biomass ash. The fusion...... characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates....

  8. Arsenic, chromium and mercury removal using mussel shell ash or a sludge/ashes waste mixture.

    Science.gov (United States)

    Seco-Reigosa, Natalia; Peña-Rodríguez, Susana; Nóvoa-Muñoz, Juan Carlos; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J; Alvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

    2013-04-01

    Different batches of valued mussel shell and waste mussel shell ash are characterised. Shell ash has pH > 12 and high electrical conductivities (between 16.01 and 27.27 dS m(-1)), while calcined shell shows pH values up to 10.7 and electrical conductivities between 1.19 and 3.55 dS m(-1). X-ray fluorescence, nitric acid digestion and water extractions show higher concentrations in shell ash for most parameters. Calcite is the dominant crystalline compound in this ash (95.6%), followed by aragonite. Adsorption/desorption trials were performed for mussel shell ash and for a waste mixture including shell ash, sewage sludge and wood ash, showing the following percentage adsorptions: Hg(II) >94%, As(V) >96% and Cr(VI) between 11 and 30% for shell ash; Hg(II) >98%, As(V) >88% and Cr(VI) between 30 and 88% for the waste mixture. Hg and As desorption was ash and the waste mixture, while Cr desorption was between 92 and 45% for shell ash, and between 19 and 0% for the mixture. In view of that, mussel shell ash and the mixture including shell ash, sewage sludge and wood ash could be useful for Hg(II) and As(V) removal.

  9. Employment benefits of electricity generation. A comparative assessment of lignite and natural gas power plants in Greece

    International Nuclear Information System (INIS)

    Tourkolias, C.; Damigos, D.; Diakoulaki, D.; Mirasgedis, S.

    2009-01-01

    This paper aims at developing an integrated approach for estimating the employment benefits associated with power-generation technologies. The proposed approach exploits the input-output methodology for estimating the direct, indirect and induced employment effects associated with the energy project in question, as well as two different valuation techniques, namely the 'opportunity cost of labour' approach and the 'public expenditures' approach, for expressing these effects in monetary terms. This framework has been implemented to estimate the employment benefits resulting from the development of a lignite-fired and a natural gas-fired power plant in Greece, taking into account all the stages of the corresponding fuel cycles that are undertaken domestically. The results of the analysis clearly show that lignite-fired electricity generation results in significant employment benefits amounting to 2.9-3.5 EUR/MWh in the basic scenario. On the other hand, the employment benefits associated with the examined natural gas unit were estimated at 0.4-0.6 EUR/MWh in the basic scenario. It is also worth mentioning that the significant environmental externalities of the lignite-fired electricity in Greece that have been presented in a number of studies can only be partially compensated by the estimated employment benefits. (author)

  10. Exploring the molecular and biochemical basis of ash resistance to emerald ash borer

    Science.gov (United States)

    Justin G.A. Whitehill; Daniel A. Herms; Pierluigi. Bonello

    2010-01-01

    Larvae of the emerald ash borer (EAB) (Agrilus planipennis) feed on phloem of ash (Fraxinus spp.) trees. It is hypothesized that the resistance of Asian species of ash (e.g., Manchurian ash, F. mandshurica) to EAB is due to endogenous defenses present in phloem tissues in the form of defensive proteins and/or...

  11. Properties and Leachability of Self-Compacting Concrete Incorporated with Fly Ash and Bottom Ash

    Science.gov (United States)

    Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Jamaluddin, Norwati; Bakri Abdullah, Mohd Mustafa Al

    2016-06-01

    The process of combustion in coal-fired power plant generates ashes, namely fly ash and bottom ash. Besides, coal ash produced from coal combustion contains heavy metals within their compositions. These metals are toxic to the environment as well as to human health. Fortunately, treatment methods are available for these ashes, and the use of fly ash and bottom ash in the concrete mix is one of the few. Therefore, an experimental program was carried out to study the properties and determine the leachability of selfcompacting concrete incorporated with fly ash and bottom ash. For experimental study, self-compacting concrete was produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a replacement for sand with the ratios of 10%, 20%, and 30% respectively. The fresh properties tests conducted were slump flow, t500, sieve segregation and J-ring. Meanwhile for the hardened properties, density, compressive strength and water absorption test were performed. The samples were then crushed to be extracted using Toxicity Characteristic Leaching Procedure and heavy metals content within the samples were identified accordingly using Atomic Absorption Spectrometry. The results demonstrated that both fresh and hardened properties were qualified to categorize as self-compacting concrete. Improvements in compressive strength were observed, and densities for all the samples were identified as a normal weight concrete with ranges between 2000 kg/m3 to 2600 kg/m3. Other than that, it was found that incorporation up to 30% of the ashes was safe as the leached heavy metals concentration did not exceed the regulatory levels, except for arsenic. In conclusion, this study will serve as a reference which suggests that fly ash and bottom ash are widely applicable in concrete technology, and its incorporation in self-compacting concrete constitutes a potential means of adding value to appropriate mix and design.

  12. Effect of ash components on the ignition and burnout of high ash coals

    Energy Technology Data Exchange (ETDEWEB)

    Feng, B.; Yan, R.; Zheng, C.G. [Huazhong University of Science and Technology, Wuhan (China). National Laboratory of Coal Combustion

    1998-11-01

    The effect of the ash components on the ignition and burnout of four Chinese high ash coals were studied by thermogravimetric analysis. To investigate the influence of the ash components, comparative experiments were carried out with original, deashed and impregnated coals. Eleven types of ash components, such as SiO{sub 2}, CaCO{sub 3}, MgO, Na{sub 2}CO{sub 3}, K{sub 2}CO{sub 3}, Al{sub 2}O{sub 3}, TiO{sub 2}, Fe{sub 2}O{sub 3}, FeS{sub 2}, NH{sub 4}Fe(SO{sub 4}){sub 2}{center_dot}12H{sub 2}O and FeSO{sub 4},(NH{sub 4}){center_dot}6H{sub 2}O were used in the present study. It was found that most of the ash components have negative effects. The strong influence of some ash components suggests that the combustion characteristics of high ash coal may be determined by the ash composition. 5 refs., 2 figs., 2 tabs.

  13. Combustion of producer gas from gasification of south Sumatera lignite coal using CFD simulation

    Directory of Open Access Journals (Sweden)

    Vidian Fajri

    2017-01-01

    Full Text Available The production of gasses from lignite coal gasification is one of alternative fuel for the boiler or gas turbine. The prediction of temperature distribution inside the burner is important for the application and optimization of the producer gas. This research aims to provide the information about the influence of excess air on the temperature distribution and combustion product in the non-premixed burner. The process was carried out using producer gas from lignite coal gasification of BA 59 was produced by the updraft gasifier which is located on Energy Conversion Laboratory Mechanical Engineering Department Universitas Sriwijaya. The excess air used in the combustion process were respectively 10%, 30% and 50%. CFD Simulations was performed in this work using two-dimensional model of the burner. The result of the simulation showed an increase of excess air, a reduction in the gas burner temperature and the composition of gas (carbon dioxide, nitric oxide and water vapor.

  14. Shedding of ash deposits

    DEFF Research Database (Denmark)

    Zbogar, Ana; Frandsen, Flemming; Jensen, Peter Arendt

    2009-01-01

    Ash deposits formed during fuel thermal conversion and located on furnace walls and on convective pass tubes, may seriously inhibit the transfer of heat to the working fluid and hence reduce the overall process efficiency. Combustion of biomass causes formation of large quantities of troublesome...... ash deposits which contain significant concentrations of alkali, and earth-alkali metals. The specific composition of biomass deposits give different characteristics as compared to coal ash deposits, i.e. different physical significance of the deposition mechanisms, lower melting temperatures, etc....... Low melting temperatures make straw ashes especially troublesome, since their stickiness is higher at lower temperatures, compared to coal ashes. Increased stickiness will eventually lead to a higher collection efficiency of incoming ash particles, meaning that the deposit may grow even faster...

  15. Pengaruh Kombinasi Fly Ash dan Bottom Ash sebagai Bahan Substitusi pada Campuran Beton terhadap Sifat Mekanis

    OpenAIRE

    Yahya, Tengku Tantoni; Kurniawandy, Alex; Djauhari, Zulfikar

    2017-01-01

    Fly ash and bottom ash were waste that generated from the power plant burning coal process. Fly ash and bottom ash has the potential to be developed as a basic ingredient in concrete composites. This research aimed to obtain the properties of fresh concrete and hard concrete of the combined effect of fly ash and bottom ash as a substitute ingredient in composite concrete. This research has examined the influence of a combination of waste fly ash and bottom ash to the compressive strength of a...

  16. Melting and Sintering of Ashes

    DEFF Research Database (Denmark)

    Hansen, Lone Aslaug

    1997-01-01

    -1300°C, and a trend of higher fusion temperatures with increasing contents of Al-silicates and quartz was found.c) Fly ashes, bottom ashes and deposits from coal/straw co-firing were all found to consist mainly of metal-alumina and alumina-silicates. These ashes all melt in the temperature range 1000......The thesis contains an experimental study of the fusion and sintering of ashes collected during straw and coal/straw co-firing.A laboratory technique for quantitative determination of ash fusion has been developed based on Simultaneous Thermal Analysis (STA). By means of this method the fraction......, the biggest deviations being found for salt rich (i.e. straw derived) ashes.A simple model assuming proportionality between fly ash fusion and deposit formation was found to be capable of ranking deposition rates for the different straw derived fly ashes, whereas for the fly ashes from coal/straw co-firing...

  17. Investigation on Leaching Behaviour of Fly Ash and Bottom Ash Replacement in Self-Compacting Concrete

    Science.gov (United States)

    Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Bakri Abdullah, Mohd Mustafa Al

    2016-06-01

    Fly ash and bottom ash are some of the waste generated by coal-fired power plants, which contains large quantities of toxic and heavy metals. In recent years, many researchers have been interested in studying on the properties of self-compacting concrete incorporated with fly ash and bottom ash but there was very limited research from the combination of fly ash and bottom ash towards the environmental needs. Therefore, this research was focused on investigating the leachability of heavy metals of SCC incorporated with fly ash and bottom ash by using Toxicity Characteristic Leaching Procedure, Synthetic Precipitation Leaching Procedure and Static Leaching Test. The samples obtained from the coal-fired power plant located at Peninsula, Malaysia. In this study, the potential heavy metals leached out from SCC that is produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a substitute for sand with the ratios from 10% to 30% respectively were designated and cast. There are eight heavy metals of concern such as As, Cr, Pb, Zn, Cu, Ni, Mn and Fe. The results indicated that most of the heavy metals leached below the permissible limits from the United States Environmental Protection Agency and World Health Organization limit for drinking water. As a conclusion, the minimum leaching of the heavy metals from the incorporation of fly ash and bottom ash in self-compacting concrete was found in 20% of fly ash and 20% of bottom ash replacement. The results also indicate that this incorporation could minimize the potential of environmental problems.

  18. Treatment of products from petroleum, shale, coal, lignite, etc

    Energy Technology Data Exchange (ETDEWEB)

    Jevanoff, V

    1952-06-20

    An improved process is described for treating with sodium plumbite all the products derived from crude petroleum, bituminous shale, coal, lignite, peat, etc., such as gasoline, solvents, lamp oil, gas oil, fuels, etc; the process being essentially characterized by the fact that it consists first in washing the product to be refined with a soda wash; submitting it to a treatment with sodium plumbite, without addition of sulfur, then to eliminate the sulfur plumbite compounds resulting in the treated product, using either redistillation to eliminate products remaining in the residue or filtration over an absorbing material such as active carbon, decolorizing earths.

  19. EFFECT OF MICROWAVE DRYING ON THE GRINDABILITY OF LIGNITE COAL

    OpenAIRE

    Güngören, Can; Özkan, Şafak Gökhan; Hacıfazlıoğlu, Hasan

    2016-01-01

    In this study, the representative lignite coal samples supplied from Kastamonu-Tosya region were dried in a conventional drying oven and a microwave oven, and then they were ground by a laboratory rod mill. The particle size analyses of the ground samples at various grinding times (10, 20, 30, and 60 minutes) were carried out, and the results were compared. As a result, the d80 particle sizes of the samples, dried in the conventional drying oven, were determined as 350, 183, 180, and 100 µm a...

  20. Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

    Directory of Open Access Journals (Sweden)

    Antoni

    2017-01-01

    Full Text Available Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment including water absorption, sieve analysis, and fineness modulus. Highvolume fly ash (HVFA mortar specimens were made and the compressive strength and flowability test using bottom ash after treatment are compared with that of the sand specimen. Low water to cementitious ratio was used to ensure higher strength from the cementitious paste and superplasticizer demand was determined for each treatment. The result showed that bottom ash can be used as fine aggregate replacement material. Sieve separation of the bottom ash could produce 75% of the compressive strength compared with the control sand specimen, whereas pounded bottom ash could have up to 96% of the compressive strength of the control specimen. A 28-day compressive strength of 45 MPa was achievable with 100% replacement of fine aggregate with bottom ash.

  1. Elemental characterization of lignite from Afsin-Elbistan in Turkey by k(0)-NAA

    Czech Academy of Sciences Publication Activity Database

    Kubešová, Marie; Orucoglu, E.; Haciyakupoglu, S.; Erenturk, S.; Krausová, Ivana; Kučera, Jan

    2016-01-01

    Roč. 308, č. 3 (2016), s. 1055-1062 ISSN 0236-5731 R&D Projects: GA ČR(CZ) GBP108/12/G108; GA MŠk(CZ) LM2011019 Institutional support: RVO:61389005 Keywords : Lignite * Afsin * Elbistan * neutron activation analysis * k(0) standardization Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 1.282, year: 2016

  2. Numerical analysis of single and multiple particles of Belchatow lignite dried in superheated steam

    Science.gov (United States)

    Zakrzewski, Marcin; Sciazko, Anna; Komatsu, Yosuke; Akiyama, Taro; Hashimoto, Akira; Kaneko, Shozo; Kimijima, Shinji; Szmyd, Janusz S.; Kobayashi, Yoshinori

    2018-03-01

    Low production costs have contributed to the important role of lignite in the energy mixes of numerous countries worldwide. High moisture content, though, diminishes the applicability of lignite in power generation. Superheated steam drying is a prospective method of raising the calorific value of this fuel. This study describes the numerical model of superheated steam drying of lignite from the Belchatow mine in Poland in two aspects: single and multi-particle. The experimental investigation preceded the numerical analysis and provided the necessary data for the preparation and verification of the model. Spheres of 2.5 to 30 mm in diameter were exposed to the drying medium at the temperature range of 110 to 170 °C. The drying kinetics were described in the form of moisture content, drying rate and temperature profile curves against time. Basic coal properties, such as density or specific heat, as well as the mechanisms of heat and mass transfer in the particular stages of the process laid the foundations for the model construction. The model illustrated the drying behavior of a single particle in the entire range of steam temperature as well as the sample diameter. Furthermore, the numerical analyses of coal batches containing particles of various sizes were conducted to reflect the operating conditions of the dryer. They were followed by deliberation on the calorific value improvement achieved by drying, in terms of coal ingredients, power plant efficiency and dryer input composition. The initial period of drying was found crucial for upgrading the quality of coal. The accuracy of the model is capable of further improvement regarding the process parameters.

  3. Paleoenvironmental implications from biomarker and stable isotope investigations on the Pliocene Velenje lignite seam (Slovenia)

    Energy Technology Data Exchange (ETDEWEB)

    Bechtel, A.; Sachsenhofer, R.F.; Markic, M.; Gratzer, R.; Lucke, A.; Puttmann, W. [Montan University of Leoben, Leoben (Austria)

    2003-07-01

    A Pliocene lignite seam up to 160 m thick occurs in the Velenje basin (Slovenia). The seam originated in a topogenous mire and evolved within a non-marine, transgressive setting. Differences in soluble organic matter yield and hydrocarbon content of borehole samples from the lignite are related to differences in the composition of free lipids of microbial origin and/or hydrocarbons derived from the biogeochemical degradation of plant tissue. Variations of the redox conditions within the mire are reflected by pristane/phytane ratios. The abundance of terpenoid biomarkers indicates the predominance of gymnosperms over angiosperms, which is consistent with palynomorphic spectra dominated by pollen of the Sequoia-Taxodium-Metasequoia plant community rather than by angiosperms. Evidence is also provided that the content of land plant derived biomarkers and the preservation of plant tissue is controlled by the input of resin-rich, decay-resistant conifers.

  4. PFBC development for lignite-fired CC power plants

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, F.; Meier, H.J.; Smuda, J.V.; Stuhlmueller, F. [VEAG Vereinigte Energiewerke AG (Germany)

    1994-12-31

    A power station design based on pressurised combustion in a circulating fluid-bed is used to illustrate the principle, layout and potential of a lignite-fired combined power station. The fundamental reasons for concentrating on the circulating pressurised fluid-bed consist in its improved emission values, the possibility of separating heat source and heat sink, and better operating performance (part-load). This design has been developed as part of a feasibility study supported by the Federal Ministry for Research and Tehcnology. The paper describes the design of the power plant components. Combustion trials carried out at the pilot plant in Friedrichsfield are reported and the cost-effectiveness of the innovatory design discussed. 10 figs.

  5. A comparative study of geopolymers synthesized from OXY-combustion and chemical looping combustion bottom ashes

    CSIR Research Space (South Africa)

    Nkuna, CN

    2017-04-01

    Full Text Available silicate (Na2SiO2) and sodium hydroxide solutions (5M, 10M and 15M) and the pastes were cured at 60°C for 10days. The properties of the geopolymers were characterized using: TGA, FTIR and SEM-EDX techniques. TGA analysis showed that FBC geopolymer with 5M...

  6. Ash fusion temperatures and the transformations of coal ash particles to slag

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.K.; Wall, T.F.; Creelman, R.A.; Gupta, R.P. [University of Newcastle, Newcastle, NSW (Australia). CRC for Black Coal Utilisation

    1998-07-01

    A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degree}C. The temperature corresponding to the rapid rate of shrinkage correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined using a scanning electron microscope (SEM) to identify the associated chemical and physical changes. The progressive changes in the range of chemical composition (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenisation, viscosity and ash fusion mechanisms. Alternate ash fusion temperatures based on different levels of shrinkage have also been suggested to characterise the ash deposition tendency of the coals. 13 refs., 9 figs.

  7. Interspecific proteomic comparisons reveal ash phloem genes potentially involved in constitutive resistance to the emerald ash borer.

    Science.gov (United States)

    Whitehill, Justin G A; Popova-Butler, Alexandra; Green-Church, Kari B; Koch, Jennifer L; Herms, Daniel A; Bonello, Pierluigi

    2011-01-01

    The emerald ash borer (Agrilus planipennis) is an invasive wood-boring beetle that has killed millions of ash trees since its accidental introduction to North America. All North American ash species (Fraxinus spp.) that emerald ash borer has encountered so far are susceptible, while an Asian species, Manchurian ash (F. mandshurica), which shares an evolutionary history with emerald ash borer, is resistant. Phylogenetic evidence places North American black ash (F. nigra) and Manchurian ash in the same clade and section, yet black ash is highly susceptible to the emerald ash borer. This contrast provides an opportunity to compare the genetic traits of the two species and identify those with a potential role in defense/resistance. We used Difference Gel Electrophoresis (DIGE) to compare the phloem proteomes of resistant Manchurian to susceptible black, green, and white ash. Differentially expressed proteins associated with the resistant Manchurian ash when compared to the susceptible ash species were identified using nano-LC-MS/MS and putative identities assigned. Proteomic differences were strongly associated with the phylogenetic relationships among the four species. Proteins identified in Manchurian ash potentially associated with its resistance to emerald ash borer include a PR-10 protein, an aspartic protease, a phenylcoumaran benzylic ether reductase (PCBER), and a thylakoid-bound ascorbate peroxidase. Discovery of resistance-related proteins in Asian species will inform approaches in which resistance genes can be introgressed into North American ash species. The generation of resistant North American ash genotypes can be used in forest ecosystem restoration and urban plantings following the wake of the emerald ash borer invasion.

  8. Evaluation of naturally occurring pigments of the North Bohemian lignite mining area; Bewertung von mineralischen Pigmentvorkommen des nordboehmischen Braunkohlenbeckens

    Energy Technology Data Exchange (ETDEWEB)

    Buntenbach, Stephan [TriMin Consulting - Mineral Processing, Ammerthal (Germany); Botula, Jiri [VSB-Technical Univ. of Ostrava (Czech Republic). Mineral Processing Dept.; Leonhardt, Hana

    2010-11-15

    The research project ''Mineral Processing Methods for the Preparation of Naturally Occurring Pigments from Overburden of the Lignite Mines and from Shallow Clay Deposits of the North Bohemian Lignite Basin'', funded by the Deutsche Bundesstiftung Umwelt DBU, was conducted as a collaboration between the AKW Apparate+Verfahren GmbH, Hirschau with the Technical University of Ostrava. Geological, mineralogical and mineral processing studies for the development of a suitable beneficiation method were carried out to investigate the possibilities of the industrial usage of beneficiated pigments of these deposits. It should be demonstrated, that the significant reserves of mineral pigments in the shallow deposits and also in the overburden of the lignite mines can be utilized ecologically and economically. Based on the results of geological prospecting work already carried out, the deposit Horenec was selected as the most important pigment deposits for the production of bolus and ochre earth. The newly carried out geological, mineralogical and chemical studies formed the basis for the following mineral processing test work and the test work for the usage of beneficiated products as colouring paint for plastic, fabric and other materials. (orig.)

  9. Emission performance and combustion efficiency of a conical fluidized-bed combustor firing various biomass fuels

    International Nuclear Information System (INIS)

    Permchart, W.; Kouprianov, V.I.

    2004-01-01

    This paper summarizes the results of an experimental study on combustion of three distinct biomass fuels (sawdust, rice husk and pre-dried sugar cane bagasse) in a single fluidized-bed combustor (FBC) with a conical bed using silica sand as the inert bed material. Temperature, CO, NO and O 2 concentrations along the combustor height as well as in flue (stack) gas were measured in the experimental tests. The effects of fuel properties and operating conditions (load and excess air) on these variables were investigated. Both CO and NO axial profiles were found to have a maximum whose location divides conventionally the combustor volume into formation (lower) and reduction (upper) regions for these pollutants. Based on CO emission and unburned carbon content in fly ash, the combustion efficiency of the conical FBC was quantified for the selected biomass fuels fired under different operating conditions. (Author)

  10. COFIRING BIOMASS WITH LIGNITE COAL; F

    International Nuclear Information System (INIS)

    Darren D. Schmidt

    2001-01-01

    As of September 28, 2001, all the major project tasks have been completed. A presentation was given to the North Dakota State Penitentiary (NDSP) and the North Dakota Division of Community Services (DCS). In general, the feasibility study has resulted in the following conclusions: (1) Municipal wood resources are sufficient to support cofiring at the NDSP. (2) Steps have been taken to address all potential fuel-handling issues with the feed system design, and the design is cost-effective. (3) Fireside issues of cofiring municipal wood with coal are not of significant concern. In general, the addition of wood will improve the baseline performance of lignite coal. (4) The energy production strategy must include cogeneration using steam turbines. (5) Environmental permitting issues are small and do not affect economics. (6) The base-case economic scenario provides for a 15-year payback of a 20-year municipal bond and does not include the broader community benefits that can be realized

  11. Aspects of combustion behaviour of coals from some New Zealand lignite-coal regions determined by thermogravimetry

    Energy Technology Data Exchange (ETDEWEB)

    Benfell, K.E.; Beamish, B.B.; Rodgers, K.A. [University of Newcastle, Callaghan, NSW (Australia). Dept. of Geology

    1997-08-25

    The papers describes how thermogravimetric analysis of five Late Cretaceous and Cenozoic New Zealand lignites demonstrate that their combustion behaviour is distinct from that of subbituminous coals and may be characterised by peak temperature of 377-416{degree}C, maximum rate of combustion of 25-31 wt% min{sup -1}, and temperature of char burnout 421-497{degree}C. These parameters reflect variation in thermal behaviour associated with both the organic and inorganic constituents of the coal. The information obtained is additional to that provided by proximate analysis; the latter is insufficient to predict the combustion behaviour of the coals relative to one another. A post-combustion thermal event is seen among the lignites as in other low-rank coals combusting below 600{degree}C, which appears to be related to the organic sulphur content of the coal.

  12. Study relating to the conceptual design and cost estimates of the Saskatchewan Power Corporation lignite beneficiation process, Phase IV: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Granatstein, D L; Champagne, P J; Szladow, A J

    1982-01-01

    The lignite beneficiation process produces a clean, environmentally acceptable and economical source of energy which offers many benefits to Saskatchewan, the public utilities and private industry. This document provides: A detailed assessment of the overall feasibility of the proposed process and its suitablity for successful commercialization; an economic evaluation including a sensitivity analysis of the major process uncertainties and alternate case analyses; an analysis of the market for beneficiated lignite; an analysis of the credits applicable to such a beneficiated product; and an outline of recommendation for process improvements and future process research and development.

  13. Coal pyrolysis under synthesis gas, hydrogen and nitrogen

    Energy Technology Data Exchange (ETDEWEB)

    Ariunaa, A.; Li Bao-Qing; Li Wen; Purevsuren, B. (and others) [Chinese Academy of Sciences, Taiyuan (China)

    2007-02-15

    Chinese Xundian, Mongolian Shiveeovoo lignites and Khoot oil shale are pyrolyzed under synthesis gas (SG) at temperature range from 400 to 800{sup o}C for lignite and from 300 to 600{sup o}C for oil shale with heating rate of 10{sup o}C/min in a fixed bed reactor. The results were compared with those obtained by pyrolysis under hydrogen and nitrogen. The results showed that unlike pyrolysis at high pressure, there are only slight different in the yields of char and tar among pyrolyses under various gases at room pressure for lignite, while higher liquid yield with lower yields of char and gas was obtained in pyrolysis of oil shale under SG and H{sub 2} than under N{sub 2}. It is found that the pyrite S can be easily removed to partially convert to organic S under various gaseous atmosphere and the total sulfur removal for oil shale is much less than lignite, which might be related to its high ash content. The higher total sulfur removal and less organic S content in the presence of SG in comparison with those under N{sub 2} and even under H{sub 2} in pyrolysis of Xundian lignite might result from the action of CO in SG. However, CO does not show its function in pyrolysis of Khoot oil shale, which might also be related to the high ash content. The results reported show the possibility of using synthesis gas instead of pure hydrogen as the reactive gas for coal hydropyrolysis. 11 refs., 4 figs., 6 tabs.

  14. Environmental impact assessment of coal fired thermal power stations

    International Nuclear Information System (INIS)

    Nambi, K.S.V.; Sadasivan, S.; Negi, B.S.; Meenakshy, V.

    1992-01-01

    Coal fly ash samples collected from various thermal power plants and one lignite ash sample were analysed for various elements such as As, Ca, Ce, Co, Cr, Cu, Eu, Fe, Hf, K, La, Lu, Mn, Na, Ni, Pb, Rb, Se, Si, Sb, Sc, Sm, Sr, Ti, V, Yb and Zn using energy dispersive X-ray fluorescence and instrumental neutron activation analysis methods. The two-step maximum leachability test was also performed on all fly ash samples. 13 refs, 9 tabs

  15. The need for verification of the Polish lignite deposits owing to development and nature conservation protection on land at the surface

    Directory of Open Access Journals (Sweden)

    Naworyta Wojciech

    2016-12-01

    Full Text Available Poland is a country rich in lignite. The area where the lignite occurs occupies approx. 22% of the total surface area of the country. Geological resources of Polish lignite deposits are estimated at 23.5 billion Mg, but in the majority (69% the accuracy of their identification is poor. Nevertheless the amount of coal in Polish deposits allows - at least in theory - for mining and energy production at the current level for hundreds of years to come. It is an important raw material for the energy security of the country both currently and in the future. Because the vast majority of Polish and foreign mines use an open pit method for lignite extraction the actual amount of mineral available for the extraction depends not only on the properties of the deposit but to a large extent on the method of development of the surface land above the deposit, as well as on the sensitivity of the environment in the vicinity of any future mines. After careful analysis it can be stated that only a few of the lignite deposits may be subject to cost-effective mining operations. These deposits should be subjected to special protection as a future resource base which will ensure the energy security of the country. Some examples of domestic deposits have been presented where due to the conflict resulting from the development of the area should be deleted from the Balance Sheet of Mineral Deposits because their exploitation is irrational and uneconomic. Keeping such deposits in the Balance Sheet, and the use of large numbers in the context of their resource base leads to an unwarranted sense of wealth which consequently does not encourage the protection of these deposits which may actually be subject to rational exploitation in the near future. In summary there is a need to find a compromise in order to adequately protect all natural resources including mineral deposits.

  16. Survey for tolerance to emerald ash borer within North American ash species

    Science.gov (United States)

    Jennifer L. Koch; Mary E. Mason; David W. Carey; Kathleen Knight; Therese Poland; Daniel A. Herms

    2010-01-01

    Since the discovery of the emerald ash borer (EAB) near Detroit, MI, in 2002, more than 40 million ash trees have been killed and another 7.5 billion are at risk in the United States. When the EAB outbreak was initially discovered, our native ash species appeared to have no resistance to the pest.

  17. Scientific investigations accompanying recultivation of abandoned lignite mines in East Germany. Research projects 1994 through 2000; Wissenschaftliche Begleitung der ostdeutschen Braunkohlesanierung. Forschungsprojekte 1994 bis 2000

    Energy Technology Data Exchange (ETDEWEB)

    Gockel, G.; Hildmann, E.; Schlenstedt, J.; Schreiber, M. (comps.)

    2001-07-01

    From 1990 the reduction of lignite mining on the territory of the German Democratic Republic (GDR) led to the closure of plants for the production and processing of lignite. This entailed a dramatic demand of redevelopment and transformation of former mining and industrial areas of lignite industry and the creation of the industrial branch of remediation of post-lignite-mining areas, for which suitable structures of management and financing had to be found. The target of these endeavours is the creation of multifunctional to follow former surface mining areas. Ecological and security criteria play an eminent part in this process. Stabilising slopes, recultivation, rehabilitation of a balanced water regime and the elimination of dangers emanating from groundwater and soil contamination by earlier industrial use have particular priority. Recultivation requires scientific preparation and surveillance. Deficits are discussed that have led to the invitation of tenders for a promotion initiative and resulted in the implementation of a number of research projects. This publication deals with the presentation of the tasks and research approaches as well as the description and evaluation of results with the view of their applicability. (orig.)

  18. Hydrogen-rich gas as a product of two-stage co-gasification of lignite/waste mixtures

    Czech Academy of Sciences Publication Activity Database

    Straka, Pavel; Bičáková, Olga

    2014-01-01

    Roč. 39, č. 21 (2014), s. 10987-10995 ISSN 0360-3199 Institutional support: RVO:67985891 Keywords : co-gasification * waste plastics * lignite * hydrogen-rich gas Subject RIV: DM - Solid Waste and Recycling Impact factor: 3.313, year: 2014 http://authors.elsevier.com/sd/article/S0360319914014025

  19. Can ash clog soil pores?

    Science.gov (United States)

    Stoof, Cathelijne; Stoof, Cathelijne; Gevaert, Anouk; Gevaert, Anouk; Baver, Christine; Baver, Christine; Hassanpour, Bahareh; Hassanpour, Bahareh; Morales, Veronica; Morales, Veronica; Zhang, Wei; Zhang, Wei; Martin, Deborah; Martin, Deborah; Steenhuis, Tammo; Steenhuis, Tammo

    2015-04-01

    Wildfire can greatly increase a landscape's vulnerability to flooding and erosion events, and ash is thought to play a large role in controlling runoff and erosion processes after wildfire. Although ash can store rainfall and thereby reduce runoff and erosion for a limited period after wildfires, it has also been hypothesized to clog soil pores and reduce infiltration. Several researchers have attributed the commonly observed increase in runoff and erosion after fire to the potential pore-clogging effect of ash. Evidence is however incomplete, as to date, research has solely focused on identifying the presence of ash in the soil, with the actual flow processes associated with the infiltration and pore-clogging of ash remaining a major unknown. In several laboratory experiments, we tested the hypothesis that ash causes pore clogging to the point that infiltration is hampered and ponding occurs. We first visualized and quantified pore-scale infiltration of water and ash in sand of a range of textures and at various infiltration rates, using a digital bright field microscope capturing both photo and video. While these visualization experiments confirm field and lab observation of ash washing into soil pores, we did not observe any clogging of pores, and have not been able to create conditions for which this does occur. Additional electrochemical analysis and measurement of saturated hydraulic conductivity indicate that pore clogging by ash is not plausible. Electrochemical analysis showed that ash and sand are both negatively charged, showing that attachment of ash to sand and any resulting clogging is unlikely. Ash also had quite high saturated conductivity, and systems where ash was mixed in or lying on top of sand had similarly high hydraulic conductivity. Based on these various experiments, we cannot confirm the hypothesis that pore clogging by ash contributes to the frequently observed increase in post-fire runoff, at least for the medium to coarse sands

  20. Re-evaluation of the age of the Brandon Lignite (Vermont, USA) based on plant megafossils. [USA - Vermont

    Energy Technology Data Exchange (ETDEWEB)

    Tiffney, B.H. (University of California at Santa Barbara, Santa Barbara, CA (United States). Dept. of Geological Sciences)

    1994-07-01

    The Brandon Lignite of west-central Vermont contains the northernmost megafossil flora of Cenozoic angiosperms, and one of the most diverse Cenozoic pollen floras in northeastern North America. While the floristic composition clearly indicates deposition of the Brandon sediments in the warmer parts of the Cenozoic, previous attempts at a more precise stratigraphic placement have been inconclusive, ranging from Cretaceous to Miocene. Re-evaluation of existing and new fruit, seed and wood data from the Brandon flora in the context of other floras in the Northern Hemisphere leads to the conservative conclusion that the deposit could range from earliest Oligocene to Early Miocene. Several lines of potentially weak evidence favor an Early Miocene age, in agreement with recent biostratigraphic data from the associated pollen flora. It is concluded that the Brandon Lignite is Early Miocene.

  1. Quantitative spectrographic determination of traces of germanium in lignite

    International Nuclear Information System (INIS)

    Martin, M.; Roca, M.

    1972-01-01

    A burning technique in a d.c. arc at 10 amp has been employed. The standards have been prepared from a natural lignite with a low germanium content. In order to enhance sensitivity, AgCl, K 2 SO 4 , CuF 2 , Sb 2 S 3 and Bi 2 S 3 have been tested as sweeping materials. Using 2% CuF 2 a detection limit of 1 ppm germanium is attainable. Bi, Cu, Sb and Sn have been studied as internal standards: the former leads to the, highest precision (1 6%. Results show good agreement with those obtained by the addition method. (Author) 6 refs

  2. Structural degradation of Thar lignite using MW1 fungal isolate: optimization studies

    Science.gov (United States)

    Haider, Rizwan; Ghauri, Muhammad A.; Jones, Elizabeth J.; Orem, William H.; SanFilipo, John R.

    2015-01-01

    Biological degradation of low-rank coals, particularly degradation mediated by fungi, can play an important role in helping us to utilize neglected lignite resources for both fuel and non-fuel applications. Fungal degradation of low-rank coals has already been investigated for the extraction of soil-conditioning agents and the substrates, which could be subjected to subsequent processing for the generation of alternative fuel options, like methane. However, to achieve an efficient degradation process, the fungal isolates must originate from an appropriate coal environment and the degradation process must be optimized. With this in mind, a representative sample from the Thar coalfield (the largest lignite resource of Pakistan) was treated with a fungal strain, MW1, which was previously isolated from a drilled core coal sample. The treatment caused the liberation of organic fractions from the structural matrix of coal. Fungal degradation was optimized, and it showed significant release of organics, with 0.1% glucose concentration and 1% coal loading ratio after an incubation time of 7 days. Analytical investigations revealed the release of complex organic moieties, pertaining to polyaromatic hydrocarbons, and it also helped in predicting structural units present within structure of coal. Such isolates, with enhanced degradation capabilities, can definitely help in exploiting the chemical-feedstock-status of coal.

  3. Adsorption of an anionic dispersant on lignite

    Energy Technology Data Exchange (ETDEWEB)

    Yavuz, R.; Kucukbayrak, S. [Istanbul Technical University, Istanbul (Turkey). Dept. of Chemical Engineering, Chemical & Metallurgical Engineering Faculty

    2001-12-01

    Since coal is not a homogeneous substance but a mixture of carbonaceous materials and mineral matter, it has a variety of surface properties. Therefore, it is not easy to control the properties of coal suspensions by simply adjusting variables, such as pH and/or electrolyte. A chemical agent needs to be added to control the properties of the coal suspensions. The adsorption behavior of an anionic dispersant in the presence of a wetting agent using some Turkish lignite samples was investigated. The effects of dispersant concentration, temperature and pH on the dispersant adsorption were studied systematically, and the experimental results are presented. Pellupur B69 as a dispersant, commercial mixture of formaldehyde condensate sodium salt of naphthalene sulphonic acid, and Texapon N{sub 2}5 as a wetting agent, a sodium lauryl ether sulfate, have been used.

  4. Spatiotemporal mapping of ground water pollution in a Greek lignite basin, using geostatistics

    Energy Technology Data Exchange (ETDEWEB)

    Modis, K. [National Technical Univ. of Athens, Athens (Greece)

    2010-07-01

    An issue of significant interest in the mining industry in Greece is the occurrence of chemical pollutants in ground water. Ammonium, nitrites and nitrates concentrations have been monitored through an extensive sampling network in the Ptolemais lignite opencast mining area in Greece. Due to intensive mining efforts in the area, the surface topology is continuously altered, affecting the life span of the water boreholes and resulting in messy spatiotemporal distribution of data. This paper discussed the spatiotemporal mapping of ground water pollution in the Ptolemais lignite basin, using geostatistics. More specifically, the spatiotemporal distribution of ground water contamination was examined by the application of the bayesian maximum entropy theory which allows merging spatial and temporal estimations in a single model. The paper provided a description of the site and discussed the materials and methods, including samples and statistics; variography; and spatiotemporal mapping. It was concluded that in the case of the Ptolemais mining area, results revealed an underlying average yearly variation pattern of pollutant concentrations. Inspection of the produced spatiotemporal maps demonstrated a continuous increase in the risk of ammonium contamination, while risk for the other two pollutants appeared in hot spots. 18 refs., 1 tab., 7 figs.

  5. Spatiotemporal mapping of ground water pollution in a Greek lignite basin, using geostatistics

    International Nuclear Information System (INIS)

    Modis, K.

    2010-01-01

    An issue of significant interest in the mining industry in Greece is the occurrence of chemical pollutants in ground water. Ammonium, nitrites and nitrates concentrations have been monitored through an extensive sampling network in the Ptolemais lignite opencast mining area in Greece. Due to intensive mining efforts in the area, the surface topology is continuously altered, affecting the life span of the water boreholes and resulting in messy spatiotemporal distribution of data. This paper discussed the spatiotemporal mapping of ground water pollution in the Ptolemais lignite basin, using geostatistics. More specifically, the spatiotemporal distribution of ground water contamination was examined by the application of the bayesian maximum entropy theory which allows merging spatial and temporal estimations in a single model. The paper provided a description of the site and discussed the materials and methods, including samples and statistics; variography; and spatiotemporal mapping. It was concluded that in the case of the Ptolemais mining area, results revealed an underlying average yearly variation pattern of pollutant concentrations. Inspection of the produced spatiotemporal maps demonstrated a continuous increase in the risk of ammonium contamination, while risk for the other two pollutants appeared in hot spots. 18 refs., 1 tab., 7 figs.

  6. Ash study for biogas purification

    International Nuclear Information System (INIS)

    Juarez V, R. I.

    2016-01-01

    This work evaluates the ashes generated from the wood and coal combustion process of the thermoelectric plant in Petacalco, Guerrero (Mexico) in order to determine its viability as a filter in the biogas purification process. The ash is constituted by particles of morphology and different chemical properties, so it required a characterization of the same by different analytical techniques: as was scanning electron microscopy and X-ray diffraction, in order to observe the microstructure and determine the elemental chemical composition of the particles. Prior to the analysis, a set of sieves was selected to classify as a function of particle size. Four different types of ashes were evaluated: one generated by the wood combustion (wood ash) and three more of the Petacalco thermoelectric generated by the coal combustion (wet fly ash, dry fly ash and dry bottom ash). (Author)

  7. Lunar ash flows - Isothermal approximation.

    Science.gov (United States)

    Pai, S. I.; Hsieh, T.; O'Keefe, J. A.

    1972-01-01

    Suggestion of the ash flow mechanism as one of the major processes required to account for some features of lunar soil. First the observational background and the gardening hypothesis are reviewed, and the shortcomings of the gardening hypothesis are shown. Then a general description of the lunar ash flow is given, and a simple mathematical model of the isothermal lunar ash flow is worked out with numerical examples to show the differences between the lunar and the terrestrial ash flow. The important parameters of the ash flow process are isolated and analyzed. It appears that the lunar surface layer in the maria is not a residual mantle rock (regolith) but a series of ash flows due, at least in part, to great meteorite impacts. The possibility of a volcanic contribution is not excluded. Some further analytic research on lunar ash flows is recommended.

  8. Regular Recycling of Wood Ash to Prevent Waste Production (RecAsh). Technical Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Lars E-mail: lars.t.andersson@skogsstyreslen.se

    2007-03-15

    At present, the extraction of harvest residues is predicted to increase in Sweden and Finland. As an effect of the intensified harvesting, the export of nutrients and acid buffering substances from the growth site is also increased. Wood ash could be used to compensate forest soils for such losses. Most wood fuel ash is today often deposited in landfills. If the wood ash is recycled, wood energy is produced without any significant waste production. Ash recycling would therefore contribute to decreasing the production of waste, and to maintaining the chemical quality of forest waters and biological productivity of forest soils in the long term. The project has developed, analysed and demonstrated two regular ash-recycling systems. It has also distributed knowledge gathered about motives for ash recycling as well as technical and administrative solutions through a range of media (handbooks, workshops, field demonstrations, reports, web page and information videos). Hopefully, the project will contribute to decreasing waste problems related to bio-energy production in the EU at large. The project has been organised as a separate structure at the beneficiary and divided in four geographically defined subprojects, one in Finland and three in Sweden (Central Sweden, Northern Sweden, and South-western Sweden). The work in each subproject has been lead by a subproject leader. Each subproject has organised a regional reference group. A project steering committee has been established consisting of senior officials from all concerned partners. The project had nine main tasks with the following main expected deliverables and output: 1. Development of two complete full-scale ash-recycling systems; 2. Production of handbooks of the ash recycling system; 3. Ash classification study to support national actions for recommendations; 4. Organise regional demonstrations of various technical options for ash treatment and spreading; 5. Organise national seminars and demonstrations of

  9. Electrodialytic removal of heavy metals from different fly ashes. Influence of heavy metal speciation in the ashes

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; Ottosen, Lisbeth M.; Villumsen, Arne

    2003-01-01

    Electrodialytic Remediation has recently been suggested as a potential method for removal of heavy metals from fly ashes. In this work electrodialytic remediation of three different fly ashes, i.e. two municipal solid waste incinerator (MSWI) fly ashes and one wood combustion fly ash was studied...... in lab scale, and the results were discussed in relation to the expected heavy metal speciation in the ashes. In initial leaching experiments the pH-dependent desorption characteristics of the heavy metals Cd, Pb, Zn and Cu were analogous in the two MSWI ashes, and thus it was expected......-moval efficiencies were observed, especially for Pb and Zn. Cd, the sole heavy metal of environmental concern in the wood ash, was found more tightly bonded in this ash than in the two MSWI ashes. It was suggested that complex Cd-silicates are likely phases in the wood ash whereas more soluble, condensed phases...

  10. Biochar and lignite affect H+-ATPase and H+-PPase activities in root tonoplast and nutrient contents of mung bean under salt stress.

    Science.gov (United States)

    Torabian, Shahram; Farhangi-Abriz, Salar; Rathjen, Judith

    2018-05-31

    This research was conducted to evaluate effects of biochar (50 and 100 g kg -1 soil) and lignite (50 and 100 g kg -1 soil) treatments on H + -ATPase and H + -PPase activity of root tonoplast, nutrient content, and performance of mung bean under salt stress. High saline conditions increased H + -ATPase and H + -PPase activities in root tonoplast, sodium (Na) content, reactive oxygen species (H 2 O 2 and O 2 - ) generation, relative electrolyte leakage (REL) and 2,2-Diphenyl-1-picrylhydrazyl (DPPH) activity in root and leaf, but decreased relative water content (RWC), chlorophyll content index, leaf area, potassium (K), calcium (Ca), magnesium (Mg), zinc (Zn) and iron (Fe) content of plant tissues, root and shoot dry weight of mung bean. Lignite and biochar treatments decreased the H + -ATPase and H + -PPase activities of root tonoplast under salt stress. Moreover, these treatments increased the cation exchange capacity of soil and nutrient values in plant tissues. Biochar and lignite diminished the generation of reactive oxygen species and DPPH activity in root and leaf cells, and these superior effects improved chlorophyll content index, leaf area and growth of mung bean under both conditions. In general, the results of this study demonstrated that biochar and lignite decreased the entry of Na ion into the cells, enriched plant cells with nutrients, and consequently improved mung bean performance under salt toxicity. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

  11. Evaluation of radioactive emissions of lignite-fired power plants in Turkey using the Analytic Hierarchy Process

    International Nuclear Information System (INIS)

    Bueke, Tayfun

    2013-01-01

    Radioactive emissions of 13 lignite-fired power plants in Turkey are of great concern to the public and to scientists alike. The purpose of this study is to evaluate these power plants, according to their radioactive emissions by using the Analytic Hierarchy Process. Control criteria are in particular 226 Ra, 232 Th, 40 K and 238 U emissions from the power plants. These control criteria are weighted according to the objective assessment. The calculations are repeated for three different objective assessments of control criteria namely the mortality risk coefficients for inhalation, ingestion, external exposure of 226 Ra, 232 Th, 40 K and 238 U. It has been calculated that the Can lignite-fired power plant is ranking first while the Soma-B plant is ranking last according to the radioactive emissions of the power plants when the average of three different objective control criteria are used in the calculations. (orig.)

  12. Some examples of the cavity filling along transportation routes above abandoned room and pillar lignite Mines in Tokai Region

    International Nuclear Information System (INIS)

    Sakamoto, A.; Yamada, N.; Sugiura, K.; Kawamoto, T.

    2005-01-01

    The authors describe the applications of the integrated cavity filling technique to abandoned lignite mines in Tokai region. These abandoned lignite mines were in operation until 1960's and the routes of Tokai By-Pass Expressway and the linear motor car railway line for Aichi Exposition pass over these abandoned mines. Since the size of abandoned mines were much larger than the route of the expressway and the elevated monorail, limited areas relevant to their stability had to be only filled. This article describe the details of cavity filling operations in these two projects, which may be some valuable examples for assessing the methods how to deal problems associated with mine closures in long term. (authors)

  13. Evaluation of lignite tar

    Energy Technology Data Exchange (ETDEWEB)

    Gossedin, A

    1946-01-01

    Tar from the low-temperature (450/sup 0/) carbonization of lignite from Bouches-du-Rhone was hydrogenated in the presence of a catalyst based on MoS/sub 2/ with a 3:1 H:N mixture. Processing (at 470/sup 0/ and 400 atmospheres) for maximum production of gasoline yielded 86 wt % of a product of boiling 55 to 186/sup 0/ and motor octane number 75. An alternative is to hydrogenate with a view to producing solvents and lubricants. For this purpose the tar was separated by distillation (at 20 millimeters, cutting at 220/sup 0/) into two fractions of equal volume. On hydrogenation (at 300/sup 0/ and 400 atmospheres) the light part yields a gasoline H/sub 2/O-soluble cut, a highly aromatic solvent fraction, a heavier cut (280/sup 0/ to 320/sup 0/) suitable as a plasticizer, and a phenol fraction. The heavier part of the tar is hydrogenated (at 380/sup 0/ and 400 atmospheres) to give spindle oil and lubricating oil of medium eta (11.2 centistokes at 98.2/sup 0/), moderate eta index (64), good pour point (-7/sup 0/), and good oxidizing characteristics. The overall yield of products from the two portions is 86.9% (gasoline and solvent 32, light phenols 9.7, spindle oil 14.2, medium lubricating oil 25.7, wax, 5.3%).

  14. First international ash marketing and technology conference

    Energy Technology Data Exchange (ETDEWEB)

    1978-01-01

    A total of 42 papers were presented in sessions with the following headings: production and disposal of ash - an international review; environmental, health, safety, and legal aspects of ash handling; marketing of ash; development of new uses for ash; cementitious use of ash; ash in manufactured products; and geotechnical uses of ash.

  15. The application of Airborne Laser Scaning for identifying old lignite workings - case study: the mine "Borussia" near Ośno Lubuskie (Western Poland)

    Science.gov (United States)

    Gontaszewska-Piekarz, Agnieszka; Mrówczyńska, Maria

    2018-04-01

    The paper presents the possibilities of using data obtained by airborne laser scanning for identifying areas where lignite used to be mined. The technology of airborne laser scanning presented in the paper as and its results have a vast potential in terms of identifying local terrain deformations. The paper also presents the history of lignite mining in the region of Ośno Lubuskie (the north-west of Ziemia Lubuska - western Poland). It describes underground mining in complicated geological conditions (glaciotectonic deformations). The paper is supplemented with historical maps showing the locations of the mines

  16. The Mineral Character and Geomechanical Properties of the Transitional Rocks from the Mesozoic-Neogene Contact Zone in the Bełchatów Lignite Deposit

    Directory of Open Access Journals (Sweden)

    Agnieszka Pękala

    2014-01-01

    Originality/value: Against the background of a number of published papers on the rocks accompanying lignite seams there is a lack of the "Bełchatów" mineralogical-petrographic studies of the transitional sediments in the Mesozoic-Neogene contact zone in the "Bełchatów" lignite deposit taking into account the aspect of raw materials. This paper has been produced to fill the void in this area.

  17. Diagnostic measurements on the great machines conditions of lignite surface mines

    Energy Technology Data Exchange (ETDEWEB)

    Helebrant, F.; Jurman, J.; Fries, J. [Technical University of Ostrava, Ostrava-Poruba (Czech Republic)

    2005-07-01

    An analysis of the diagnosis of loading and service dependability of a rail-mounted excavator used in surface lignite mining is described. Wheel power vibrations in electric motor bearings and electric motor input bearings to the gearbox were measured in situ, in horizontal, vertical, and axial directions. The data were analyzed using a mathematical relationship. The results are presented in a loading diagram that shows the deterioration and the acceptable lower bound of machine conditions over time. Work is continuing. 5 refs., 1 fig.

  18. Determining ash content in flotation wastes by means of the MPOF optical ash meter. [Poland

    Energy Technology Data Exchange (ETDEWEB)

    Sikora, T; Sliwa, J

    1982-03-01

    The paper evaluates an experimental unit of the MPOF optical ash meter, developed by the EMAG Research and Production Center for Electrical Engineering and Mining Automation. The MPOF, which is being tested at the coal preparation plant of the 30 lecia PRL mine, is the first system for continuous determination of ash content in flotation tailings developed in Poland. A block scheme of the system is given. It consists of a measuring head and electronic system which processes data supplied by the measuring head and calculates ash content. System operation is based on the principle of determining ash content in a mixture of coal and mineral wastes by measuring mixture reflectivity. Determining ash content in the mixture is possible as reflectivity coefficients for coal and ash are constant. Performance of the MPOF optical ash meter is evaluated; the results are shown in a table and a scheme. Measurement accuracy is satisfactory.

  19. Effects of vesicular-arbuscular mycorrhizae on survival and growth of perennial grasses in lignite overburden in Texas

    Energy Technology Data Exchange (ETDEWEB)

    Call, C.A.; Davies, F.T.

    1988-12-01

    Seedlings of sideoats grama (Bouteloua curtipendula), Indiangrass (Sorghastrum nutans), and kleingrass (Panicum coloratum) were inoculated with vesicular-arbuscular mycorrhizal (VAM) fungi (Glomus fasciculatum and Gigaspora margarita) in a containerized system and transplanted into lignite overburden in the Post Oak Savannah region of Texas, U.S.A. After three growing seasons without cultural inputs, plants inoculated with VAM fungi had greater survival percentages, basal diameters, and above-ground biomass than noninoculated plants. Inoculated plants had higher levels of nitrogen and phosphorus in above-ground biomass than noninoculated plants. Root colonization percentages of inoculated plants remained fairly stable while noninoculated plants showed low levels of colonization over the 3-year study period. Vesicular-arbuscular mycorrhizae enhanced the survival and growth of the 3 grass species by making effective use of limited resources in the lignite overburden. 31 refs., 3 tabs.

  20. Ash Properties of Alternative Biomass

    DEFF Research Database (Denmark)

    Capablo, Joaquin; Jensen, Peter Arendt; Pedersen, Kim Hougaard

    2009-01-01

    analysis into three main groups depending upon their ash content of silica, alkali metal, and calcium and magnesium. To further detail the biomass classification, the relative molar ratio of Cl, S, and P to alkali were included. The study has led to knowledge on biomass fuel ash composition influence...... on ash transformation, ash deposit flux, and deposit chlorine content when biomass fuels are applied for suspension combustion....

  1. Radiation exposure potential from coal-fired power plants in Romania

    International Nuclear Information System (INIS)

    Botezatu, E.; Grecea, C.; Botezatu, G.; Capitanu, O.; Peic, T.; Sandor, G.

    1996-01-01

    In the investigated power plants they burn brown coal, lignite and/or mixture of different kinds of coal: brown coal, lignite, pit coal, pitch coal, bituminous coal. The activity concentrations measured in the coal samples varied over two orders of magnitude. The natural radionuclide concentrations in fly ash are significantly higher than the corresponding Concentrations in the coal. The normalized discharged activities for the investigated power plants are much higher than those estimated in the UNSCEAR 1988 Report for typical old and modern plants. Firstly, accounting for this is the low ash retention efficiency of the particulate control devices of power stations, especially for the older ones, and secondly, the high ash content of the coal: 26-60%. The low quality of coal leads to the higher coal consumption; thus the combustion of up to 20.109 Kg of coal is required to produce 1 Gwa of electrical energy. As a result, the activities of radon-222 and of radon-220 released per Gwa have been assessed at 25 to 770 GBq. (author)

  2. Biotic and abiotic factors affect green ash volatile production and emerald ash borer adult feeding preference.

    Science.gov (United States)

    Chen, Yigen; Poland, Therese M

    2009-12-01

    The emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is an exotic woodborer first detected in 2002 in Michigan and Ontario and is threatening the ash resource in North America. We examined the effects of light exposure and girdling on green ash (Fraxinus pennsylvanica Marsh) volatile production, and effects of light exposure, girdling, and leaf age on emerald ash borer adult feeding preferences and phototaxis. Green ash seedlings grown under higher light exposure had lower amounts of three individual volatile compounds, (Z)-3-hexenol, (E)-beta-ocimene, and (Z,E)-alpha-farnesene, as well as the total amount of six detected volatile compounds. Girdling did not affect the levels of these volatiles. Emerald ash borer females preferred mature leaves, leaves from girdled trees, and leaves grown in the sun over young leaves, leaves from nongirdled trees, and leaves grown in the shade, respectively. These emerald ash borer preferences were most likely because of physical, nutritional, or biochemical changes in leaves in response to the different treatments. Emerald ash borer females and males showed positive phototaxis in laboratory arenas, a response consistent with emerald ash borer preference for host trees growing in sunlight.

  3. 10 Risk to Ash from Emerald Ash Borer: Can Biological Control Prevent the Loss of Ash Stands

    Science.gov (United States)

    Ash trees were once relatively free of serious, major diseases and insect pests in North America until the arrival of EAB, which was first detected in North America in Michigan in 2002. As of February 2014, EAB had been detected in 22 U.S. states and two Canadian provinces, killing millions of ash ...

  4. Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

    OpenAIRE

    Antoni; Sulistio Aldi Vincent; Wahjudi Samuel; Hardjito Djwantoro; Hardjito Djwantoro

    2017-01-01

    Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment includi...

  5. Evaluation of radioactive emissions of lignite-fired power plants in Turkey using the Analytic Hierarchy Process

    Energy Technology Data Exchange (ETDEWEB)

    Bueke, Tayfun [Mugla Sitki Kocman Univ., Mugla (Turkey). Dept. of Energy Systems Engineering

    2013-11-15

    Radioactive emissions of 13 lignite-fired power plants in Turkey are of great concern to the public and to scientists alike. The purpose of this study is to evaluate these power plants, according to their radioactive emissions by using the Analytic Hierarchy Process. Control criteria are in particular {sup 226}Ra, {sup 232}Th, {sup 40}K and {sup 238}U emissions from the power plants. These control criteria are weighted according to the objective assessment. The calculations are repeated for three different objective assessments of control criteria namely the mortality risk coefficients for inhalation, ingestion, external exposure of {sup 226}Ra, {sup 232}Th, {sup 40}K and {sup 238}U. It has been calculated that the Can lignite-fired power plant is ranking first while the Soma-B plant is ranking last according to the radioactive emissions of the power plants when the average of three different objective control criteria are used in the calculations. (orig.)

  6. Characterization of metals released from coal fly ash during dredging at the Kingston ash recovery project.

    Science.gov (United States)

    Bednar, A J; Averett, D E; Seiter, J M; Lafferty, B; Jones, W T; Hayes, C A; Chappell, M A; Clarke, J U; Steevens, J A

    2013-09-01

    A storage-pond dike failure occurred on December 22, 2008 at the Tennessee Valley Authority Kingston Fossil Plant resulting in the release of over 4million cubic meters (5million cubic yards) of fly ash. Approximately half of the released ash was deposited in the main channel of the Emory River, Tennessee, USA. Remediation efforts of the Emory River focused on hydraulic dredging, as well as mechanical excavation in targeted areas. However, agitation of the submerged fly ash during hydraulic dredging introduces river water into the fly ash material, which could promote dissolution and desorption of metals from the solid fly ash material. Furthermore, aeration of the dredge slurry could alter the redox state of metals in the fly ash material and thereby change their sorption, mobility, and toxicity properties. The research presented here focuses on the concentrations and speciation of metals during the fly ash recovery from the Emory River. Our results indicate that arsenite [As(III)] released from the fly ash material during dredging was slowly oxidized to arsenate [As(V)] in the slurry recovery system with subsequent removal through precipitation or sorption reactions with suspended fly ash material. Concentrations of other dissolved metals, including iron and manganese, also generally decreased in the ash recovery system prior to water discharge back to the river. Published by Elsevier Ltd.

  7. Prospects for ash pond reclamation

    Energy Technology Data Exchange (ETDEWEB)

    Shyyam, A.K.; Shukla, K.S.; Agrawal, D. (National Thermal Power Corporation Ltd., New Delhi (India))

    1993-01-01

    A typical modern coal fired station in India burns 0.7 t/MWh of coal and consequently generates ash at 0.245 t/MWh. The physical nature of ash, low available concentrations of certain plant nutrients and the presence of phytotoxic trace elements render fly ash marginally adequate for plant growth. As fly ash itself was thought to be an inappropriate growth medium for plants, regulators decided that a soil cover is mandatory. There is ample data to suggest that the attributes of fly ash detrimental to plant growth can be ameliorated, allowing the establishment of vegetation directly on fly ash surfaces. The natural revegetation of fly ash disposal sites has been reported in the world. The natural vegetation pioneered by Cynodon at different stages of ecological succession and comprising of species such as [ital Calotropis gigantea], [ital Lippia nodiflora], [ital Ipomea, cornea], [ital Xanthium parviflorum] has been noted at one of the NTPC projects, in Badarpur Thermal Power Station. Since natural reclamation is a time-consuming process, experimental trials of growing some species over the temporary ash lagoon directly (without soil cover) were carried out at Ramagundam Super Thermal Power Project (RSTPP) of NTPC, in South India to achieve faster results than the natural process. 6 refs., 8 figs.

  8. Degradation of Thermal Barrier Coatings from Deposits and Its Mitigation

    Energy Technology Data Exchange (ETDEWEB)

    Nitin Padture

    2011-12-31

    Ceramic thermal barrier coatings (TBCs) used in gas-turbine engines afford higher operating temperatures, resulting in enhanced efficiencies and performance. However, in the case of syngas-fired engines, fly ash particulate impurities that may be present in syngas can melt on the hotter TBC surfaces and form glassy deposits. These deposits can penetrate the TBCs leading to their failure. In experiments using lignite fly ash to simulate these conditions we show that conventional TBCs of composition 93wt% ZrO{sub 2} + 7wt% Y{sub 2}O{sub 3} (7YSZ) fabricated using the air plasma spray (APS) process are completely destroyed by the molten fly ash. The molten fly ash is found to penetrate the full thickness of the TBC. The mechanisms by which this occurs appear to be similar to those observed in degradation of 7YSZ TBCs by molten calcium-magnesium-aluminosilicate (CMAS) sand and by molten volcanic ash in aircraft engines. In contrast, APS TBCs of Gd{sub 2Zr{sub 2}O{sub 7} composition are highly resistant to attack by molten lignite fly ash under identical conditions, where the molten ash penetrates ~25% of TBC thickness. This damage mitigation appears to be due to the formation of an impervious, stable crystalline layer at the fly ash/Gd{sub 2}Zr{sub 2}O{sub 7} TBC interface arresting the penetrating moltenfly- ash front. Additionally, these TBCs were tested using a rig with thermal gradient and simultaneous accumulation of ash. Modeling using an established mechanics model has been performed to illustrate the modes of delamination, as well as further opportunities to optimize coating microstructure. Transfer of the technology was developed in this program to all interested parties.

  9. Radioisotope conveyor ash meter

    International Nuclear Information System (INIS)

    Savelov, V.D.

    1994-01-01

    Radioisotope conveyor ash meter realizes persistent measuring of ashiness of coal and products of its enrichment on the belt conveyor without contact. The principle of ash meter acting is based on functional dependence of the gamma radiation flows backscattering intensity of radioisotope sources from the ash volume content in the controlled fuel. Facility consists from the ashiness transducer and the processing and control device

  10. Bioleaching of trace metals from coal ash using local isolate from coal ash ponds

    Directory of Open Access Journals (Sweden)

    Pangayao Denvert

    2018-01-01

    Full Text Available Bioleaching of chromium, copper, manganese and zinc from coal ash were investigated using isolates from coal ash ponds particularly Psuedomonas spp. Six (6 different coal ash ponds were examined however, after initial screening Psuedomonas spp. were only present in three (3 coal ash ponds. Among the three coal ash ponds, results showed that eight (8 putative Pseudomonas spp. isolates were present that were identified using the Polymerase Chain Reaction (PCR. Using the eight putative Pseudomonas spp. for bioleaching at optimum conditions and 15 days, the pH value ranges from 8.26 to 8.84 which was basic in nature. Moreover, the maximum metal leached were 8.04% Cr, 12.05% Cu, 4.34% Mn and 10.63% Zn.

  11. Lignite and hard coal: Energy suppliers for world needs until the year 2100 - An outlook

    International Nuclear Information System (INIS)

    Thielemann, Thomas; Schmidt, Sandro; Peter Gerling, J.

    2007-01-01

    For three years, international hard coal prices have been at rather expensive levels. Some argue that these higher prices might indicate the threat of a physical scarcity of fossil fuels - similar to the situation with oil and gas. This is not true. The supply situations with lignite and hard coal appear to be largely not critical. Adjusted to the rise in global coal consumption, which is expected until 2100, nature by and large can meet the world's coal demand. This is shown for lignite in this article and it is illustrated for hard coal here, differentiated in space and time for a world divided into eight regions and viewed for the years 2005, 2020, 2030, 2050, and 2100. The only area of potential concern is Asia (especially China). But today's and coming eager efforts in China to convert coal resources into reserves will most likely deliver the coal needed for the Chinese market. Up to the year 2100, and from a geoscientific point of view, there will be no bottleneck in coal supplies on this planet. (author)

  12. Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash

    Directory of Open Access Journals (Sweden)

    Martin Ernesto Kalaw

    2016-07-01

    Full Text Available Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC, which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1 their technical properties are comparable if not better; (2 they can be produced from industrial wastes; and (3 within reasonable constraints, their production requires less energy and emits significantly less CO2. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA and coal bottom ash (CBA, and rice hull ash (RHA. The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF for elemental and X-ray diffraction (XRD for mineralogical composition. The raw materials’ thermal stability and loss on ignition (LOI were determined using thermogravimetric analysis (TGA and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR

  13. Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash.

    Science.gov (United States)

    Kalaw, Martin Ernesto; Culaba, Alvin; Hinode, Hirofumi; Kurniawan, Winarto; Gallardo, Susan; Promentilla, Michael Angelo

    2016-07-15

    Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC), which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1) their technical properties are comparable if not better; (2) they can be produced from industrial wastes; and (3) within reasonable constraints, their production requires less energy and emits significantly less CO₂. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC) use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA) and coal bottom ash (CBA), and rice hull ash (RHA). The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF) for elemental and X-ray diffraction (XRD) for mineralogical composition. The raw materials' thermal stability and loss on ignition (LOI) were determined using thermogravimetric analysis (TGA) and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP) analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR), scanning

  14. Low temperature coal depolymerization-liquefaction: conversion of a North Dakota lignite to a light hydrocarbon oil

    Energy Technology Data Exchange (ETDEWEB)

    Shabtai, J.; Yuan Zhang (University of Utah, Salt Lake City, UT (USA). Dept. of Fuels Engineering)

    1989-10-01

    A new low temperature method of coal liquefaction is described which includes intercalation of the coal with FeCl{sub 3}, depolymerization under supercritical conditions, and hydroprocessing of the depolymerized product. Results indicate a high yield conversion of lignites to light hydrocarbon oils. 6 refs., 4 figs., 1 tab.

  15. Co-processing of lignite-plastic mixtures into liquid distillate fractions in the presence of iron catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, B.N.; Sharypov, V.I.; Beregovtsova, N.G.; Baryshnikov, S.V.; Doroginskaya, A.N. [Russian Academy of Sciences, Krasnoyarsk (Russian Federation). Inst. of Chemistry of Natural Organic Materials Sibirian Branch

    1997-12-31

    Some features of co-processing of Kansk-Achinsk lignite with plastics into hydrocarbon mixtures in the presence of activated iron-containing minerals (hematite, magnetite, pyrrhotite) were investigated under various operating parameters. The following catalytic processes were studied: pyrolysis in an inert atmosphere, hydropyrolysis and water-steam cracking. (orig.)

  16. Use of lignite in the production of sponge iron and processing of waste oxides in rotary kilns

    Energy Technology Data Exchange (ETDEWEB)

    Eichberger, H; Schnabel, W; Serbent, H

    1978-11-01

    Based on a study of the situation of fossil energy reserves, processes are described in which non-coking coals, in particular lignite, are used for reduction in the rotary kiln, i.e. for sponge iron production and for zinc volatilization from waste oxides).

  17. Land movement monitoring at the Mavropigi lignite mine using spaceborne D-InSAR

    Science.gov (United States)

    Papadaki, Eirini; Tripolitsiotis, Achilleas; Steiakakis, Chrysanthos; Agioutantis, Zacharias; Mertikas, Stelios; Partsinevelos, Panagiotis; Schilizzi, Pavlos

    2013-08-01

    This paper examines the capability of remote sensing radar interferometry to monitor land movements, as it varies with time, in areas close to open pit lignite mines. The study area is the "Mavropigi" lignite mine in Ptolemais, Northern Greece; whose continuous operation is of vital importance to the electric power supply of Greece. The mine is presently 100-120m deep while horizontal and vertical movements have been measured in the vicinity of the pit. Within the mine, ground geodetic monitoring has revealed an average rate of movement amounting to 10-20mm/day at the southeast slopes. In this work, differential interferometry (DInSAR), using 19 Synthetic Aperture Radar (SAR) images of ALOS satellite, has been applied to monitor progression of land movement caused my mining within the greater area of "Mavropigi" region. The results of this work show that DInSAR can be used effectively to capture ground movement information, well before signs of movements can be observed visually in the form of imminent fissures and tension cracks. The advantage of remote sensing interferometry is that it can be applied even in inaccessible areas where monitoring with ground equipment is either impossible or of high-cost (large areas).

  18. Effects of the addition of oil shale ash and coal ash on physic-chemical properties of CPJ45 cement

    Directory of Open Access Journals (Sweden)

    Nabih K.

    2014-04-01

    Full Text Available We focused our research on recycling industrial wastes, fly ash (F.A, bottom ash (B.A and oil shale ash (S.A in cement production. The study concerns physico-chemical characterization of these products and the influence of their addition on the mechanical proprieties of the CPJ45 cement. XRF allowed us to rank the three additives used according to their contents on major oxides. Coal ashes belong to the class F, and thus possess poozzolanic properties and oil shale ash belongs to the class C and possesses hydraulic and poozolanic properties. The crystalline phases constituting each ash were analysed by XRD. We observe in bottom ash the presence of quartz and mullite. The same crystals are found in fly ash with hematite and magnetite. Oil shale ash is composed of quartz, anhydrite, gehlenite, wollastonite and periclase. The microstructures of fly ash and bottom ash were studied using SEM. The bottom ash was composed respectively of fine particles that are generally irregularly shaped, their dimensions are between 5 and 28μm and of big particles(300 μm. The EDX analysis coupled with an electronic microscope provided some information about the major elements that constitute our samples. The dehydrations of anhydrous and three days hydrated cement were examined by DSC. For hydrated cements we noticed endothermic peaks related to the dehydration of CSH, CH and decomposition of carbonates. The study of the mechanical properties of CPJ45 cement by adding different proportions of fly ash, bottom ash and oil shale ash helped clarifying the percentage of ash that leaded to improve the 28 days mechanical strength. The results show that the cements studied have their maximum mechanical resistance with the addition at 7% of fly ash or 10% of oil shale ash.

  19. Fly ash dynamics in soil-water systems

    International Nuclear Information System (INIS)

    Sharma, S.; Fulekar, M.H.; Jayalakshmi, C.P.

    1989-01-01

    Studies regarding the effluents and coal ashes (or fly ash) resulting from coal burning are numerous, but their disposal and interactions with the soil and water systems and their detailed environmental impact assessment with concrete status reports on a global scale are scanty. Fly ash dynamics in soil and water systems are reviewed. After detailing the physical composition of fly ash, physicochemical changes in soil properties due to fly ash amendment are summarized. Areas covered include texture and bulk density, moisture retention, change in chemical equilibria, and effects of fly ash on soil microorganisms. Plant growth in amended soils is discussed, as well as plant uptake and accumulation of trace elements. In order to analyze the effect of fly ash on the physicochemical properties of water, several factors must be considered, including surface morphology of fly ash, pH of the ash sluice water, pH adjustments, leachability and solubility, and suspended ash and settling. The dynamics of fly ash in water systems is important due to pollution of groundwater resources from toxic components such as trace metals. Other factors summarized are bioaccumulation and biomagnification, human health effects of contaminants, and the impact of radionuclides in fly ash. Future research needs should focus on reduction of the environmental impact of fly ash and increasing utilization of fly ash as a soil amendment. 110 refs., 2 figs., 10 tabs

  20. Ash cloud aviation advisories

    Energy Technology Data Exchange (ETDEWEB)

    Sullivan, T.J.; Ellis, J.S. [Lawrence Livermore National Lab., CA (United States); Schalk, W.W.; Nasstrom, J.S. [EG and G, Inc., Pleasanton, CA (United States)

    1992-06-25

    During the recent (12--22 June 1991) Mount Pinatubo volcano eruptions, the US Air Force Global Weather Central (AFGWC) requested assistance of the US Department of Energy`s Atmospheric Release Advisory Capability (ARAC) in creating volcanic ash cloud aviation advisories for the region of the Philippine Islands. Through application of its three-dimensional material transport and diffusion models using AFGWC meteorological analysis and forecast wind fields ARAC developed extensive analysis and 12-hourly forecast ash cloud position advisories extending to 48 hours for a period of five days. The advisories consisted of ``relative`` ash cloud concentrations in ten layers (surface-5,000 feet, 5,000--10,000 feet and every 10,000 feet to 90,000 feet). The ash was represented as a log-normal size distribution of 10--200 {mu}m diameter solid particles. Size-dependent ``ashfall`` was simulated over time as the eruption clouds dispersed. Except for an internal experimental attempt to model one of the Mount Redoubt, Alaska, eruptions (12/89), ARAC had no prior experience in modeling volcanic eruption ash hazards. For the cataclysmic eruption of 15--16 June, the complex three-dimensional atmospheric structure of the region produced dramatically divergent ash cloud patterns. The large eruptions (> 7--10 km) produced ash plume clouds with strong westward transport over the South China Sea, Southeast Asia, India and beyond. The low-level eruptions (< 7 km) and quasi-steady-state venting produced a plume which generally dispersed to the north and east throughout the support period. Modeling the sequence of eruptions presented a unique challenge. Although the initial approach proved viable, further refinement is necessary and possible. A distinct need exists to quantify eruptions consistently such that ``relative`` ash concentrations relate to specific aviation hazard categories.

  1. Identifying glass compositions in fly ash

    Directory of Open Access Journals (Sweden)

    Katherine eAughenbaugh

    2016-01-01

    Full Text Available In this study, four Class F fly ashes were studied with a scanning electron microscope; the glassy phases were identified and their compositions quantified using point compositional analysis with k-means clustering and multispectral image analysis. The results showed that while the bulk oxide contents of the fly ashes were different, the four fly ashes had somewhat similar glassy phase compositions. Aluminosilicate glasses (AS, calcium aluminosilicate glasses (CAS, a mixed glass, and, in one case, a high iron glass were identified in the fly ashes. Quartz and iron crystalline phases were identified in each fly ash as well. The compositions of the three main glasses identified, AS, CAS, and mixed glass, were relatively similar in each ash. The amounts of each glass were varied by fly ash, with the highest calcium fly ash containing the most of calcium-containing glass. Some of the glasses were identified as intermixed in individual particles, particularly the calcium-containing glasses. Finally, the smallest particles in the fly ashes, with the most surface area available to react in alkaline solution, such as when mixed with portland cement or in alkali-activated fly ash, were not different in composition than the large particles, with each of the glasses represented. The method used in the study may be applied to a fly ash of interest for use as a cementing material in order to understand its potential for reactivity.

  2. The Role of Biocontrol of Emerald Ash Borer in Protecting Ash Regeneration after Invasion

    Science.gov (United States)

    Emerald ash borer (EAB) is an invasive Asian beetle that is destroying ash in forests over much of eastern North America because of the high susceptibility of our native ash and a lack of effective natural enemies. To increase mortality of EAB larvae and eggs, the USDA (FS, ARS and APHIS) is carryin...

  3. Study of a large rapid ashing apparatus and a rapid dry ashing method for biological samples and its application

    International Nuclear Information System (INIS)

    Jin Meisun; Wang Benli; Liu Wencang

    1988-04-01

    A large rapid-dry-ashing apparatus and a rapid ashing method for biological samples are described. The apparatus consists of specially made ashing furnace, gas supply system and temperature-programming control cabinet. The following adventages have been showed by ashing experiment with the above apparatus: (1) high speed of ashing and saving of electric energy; (2) The apparatus can ash a large amount of samples at a time; (3) The ashed sample is pure white (or spotless), loose and easily soluble with few content of residual char; (4) The fresh sample can also be ashed directly. The apparatus is suitable for ashing a large amount of the environmental samples containing low level radioactivity trace elements and the medical, food and agricultural research samples

  4. Selective coal mining of intercalated lignite deposits

    Energy Technology Data Exchange (ETDEWEB)

    Zunic, R [Kolubara-Projekt, Lazarevac (Yugoslavia)

    1991-01-01

    Describes selective coal mining in the Tamnava-Istocno Polje coal surface coal mine (Yugoslavia), designed for an annual coal production of 11.4 Mt. Until 1991, this mine exploited one thick lignite seam, without spoil intercalations, using a bucket wheel excavator-conveyor-spreader system both for coal mining and removal of overburden. In the future, several spoil intercalations of up to 1.0 m and thicker will appear with a total volume of 22 million m{sup 3}. These intercalations have to be selectively excavated in order to guarantee the calorific value of coal for the Nikola Tesla power plant. Computer calculations were carried out to determine the decrease in excavator coal production due to selective mining of spoil strata. Calculations found that the annual surface mine capacity will be lower by at most 9%, depending on thickness of spoil intercalations. The useful operation time of excavators will be reduced by 98 hours per year. The planned annual coal production will nevertheless be fulfilled. 3 refs.

  5. Volcanic ash impacts on critical infrastructure

    Science.gov (United States)

    Wilson, Thomas M.; Stewart, Carol; Sword-Daniels, Victoria; Leonard, Graham S.; Johnston, David M.; Cole, Jim W.; Wardman, Johnny; Wilson, Grant; Barnard, Scott T.

    2012-01-01

    Volcanic eruptions can produce a wide range of hazards. Although phenomena such as pyroclastic flows and surges, sector collapses, lahars and ballistic blocks are the most destructive and dangerous, volcanic ash is by far the most widely distributed eruption product. Although ash falls rarely endanger human life directly, threats to public health and disruption to critical infrastructure services, aviation and primary production can lead to significant societal impacts. Even relatively small eruptions can cause widespread disruption, damage and economic loss. Volcanic eruptions are, in general, infrequent and somewhat exotic occurrences, and consequently in many parts of the world, the management of critical infrastructure during volcanic crises can be improved with greater knowledge of the likely impacts. This article presents an overview of volcanic ash impacts on critical infrastructure, other than aviation and fuel supply, illustrated by findings from impact assessment reconnaissance trips carried out to a wide range of locations worldwide by our international research group and local collaborators. ‘Critical infrastructure’ includes those assets, frequently taken for granted, which are essential for the functioning of a society and economy. Electricity networks are very vulnerable to disruption from volcanic ash falls. This is particularly the case when fine ash is erupted because it has a greater tendency to adhere to line and substation insulators, where it can cause flashover (unintended electrical discharge) which can in turn cause widespread and disruptive outages. Weather conditions are a major determinant of flashover risk. Dry ash is not conductive, and heavy rain will wash ash from insulators, but light rain/mist will mobilise readily-soluble salts on the surface of the ash grains and lower the ash layer’s resistivity. Wet ash is also heavier than dry ash, increasing the risk of line breakage or tower/pole collapse. Particular issues for water

  6. Transcriptomic signatures of ash (Fraxinus spp. phloem.

    Directory of Open Access Journals (Sweden)

    Xiaodong Bai

    2011-01-01

    Full Text Available Ash (Fraxinus spp. is a dominant tree species throughout urban and forested landscapes of North America (NA. The rapid invasion of NA by emerald ash borer (Agrilus planipennis, a wood-boring beetle endemic to Eastern Asia, has resulted in the death of millions of ash trees and threatens billions more. Larvae feed primarily on phloem tissue, which girdles and kills the tree. While NA ash species including black (F. nigra, green (F. pennsylvannica and white (F. americana are highly susceptible, the Asian species Manchurian ash (F. mandshurica is resistant to A. planipennis perhaps due to their co-evolutionary history. Little is known about the molecular genetics of ash. Hence, we undertook a functional genomics approach to identify the repertoire of genes expressed in ash phloem.Using 454 pyrosequencing we obtained 58,673 high quality ash sequences from pooled phloem samples of green, white, black, blue and Manchurian ash. Intriguingly, 45% of the deduced proteins were not significantly similar to any sequences in the GenBank non-redundant database. KEGG analysis of the ash sequences revealed a high occurrence of defense related genes. Expression analysis of early regulators potentially involved in plant defense (i.e. transcription factors, calcium dependent protein kinases and a lipoxygenase 3 revealed higher mRNA levels in resistant ash compared to susceptible ash species. Lastly, we predicted a total of 1,272 single nucleotide polymorphisms and 980 microsatellite loci, among which seven microsatellite loci showed polymorphism between different ash species.The current transcriptomic data provide an invaluable resource for understanding the genetic make-up of ash phloem, the target tissue of A. planipennis. These data along with future functional studies could lead to the identification/characterization of defense genes involved in resistance of ash to A. planipennis, and in future ash breeding programs for marker development.

  7. Spectral analysis of white ash response to emerald ash borer infestations

    Science.gov (United States)

    Calandra, Laura

    The emerald ash borer (EAB) (Agrilus planipennis Fairmaire) is an invasive insect that has killed over 50 million ash trees in the US. The goal of this research was to establish a method to identify ash trees infested with EAB using remote sensing techniques at the leaf-level and tree crown level. First, a field-based study at the leaf-level used the range of spectral bands from the WorldView-2 sensor to determine if there was a significant difference between EAB-infested white ash (Fraxinus americana) and healthy leaves. Binary logistic regression models were developed using individual and combinations of wavelengths; the most successful model included 545 and 950 nm bands. The second half of this research employed imagery to identify healthy and EAB-infested trees, comparing pixel- and object-based methods by applying an unsupervised classification approach and a tree crown delineation algorithm, respectively. The pixel-based models attained the highest overall accuracies.

  8. Thermal treatment of ashes[Fly Ash from Municipal Waste Incineration]; Termisk rening av askor

    Energy Technology Data Exchange (ETDEWEB)

    Wikman, Karin; Berg, Magnus; Bjurstroem, Henrik [AaF-Energi och Miljoe AB, Stockholm (Sweden); Nordin, Anders [Umeaa Univ. (Sweden). Dept. of Applied Physics and Electronics

    2003-04-01

    In this project descriptions of different processes for thermal treatment of ashes have been compiled. A technical and economic evaluation of the processes has been done to identify possibilities and problems. The focus in the project lays on treatment of fly ash from municipal waste incineration but the processes can also be used to treat other ashes. When the ash is heated in the thermal treatment reactor, with or without additives, the material is sintered or vitrified and at the same time volatile substances (Zn, Pb, Cd, Hg etc.) are separated. In general the separation is more effective in processes with reducing conditions compared to oxidizing conditions. Oxidizing processes have both worse separation capacity and require more energy. The oxidizing processes are mainly used to stabilize the ash through vitrification and they are in some cases developed for management of municipal sewage sludge and bottom ash. However, these processes are often not as complex as for example an electric arc melting furnace with reducing conditions. The research today aim to develop more effective electrical melting systems with reducing conditions such as plasma melting furnaces, electric resistance melting furnaces and low frequency induction furnaces. A central question in the evaluation of different thermal treatment processes for ash is how the residues from the treatment can be used. It is not certain that the vitrified material is stable enough to get a high economic value, but it can probably be used as construction material. How the remaining metals in the ash are bound is very important in a long-time perspective. Further studies with leaching tests are necessary to clarify this issue. The heavy metal concentrate from the processes contains impurities, such as chlorine, which makes it unprofitable to obtain the metals. Instead the heavy metal concentrate has to be land filled. However, the amount of material for land filling will be much smaller if only the heavy

  9. Application of Coal Ash to Postmine Land for Prevention of Soil Erosion in Coal Mine in Indonesia: Utilization of Fly Ash and Bottom Ash

    Directory of Open Access Journals (Sweden)

    Shinji Matsumoto

    2016-01-01

    Full Text Available The increase in the number of coal-fired power plants with the increase in coal production and its consumption has caused the problem of the treatment of a large amount of coal ash in Indonesia. In the past studies, coal ash was applied to postmine land with the aim of improving soil conditions for plant growth; however, heavy rain in the tropical climate may cause soil erosion with the change in soil conditions. This study presents the effects of application of coal ash to postmine land on soil erosion by performing the artificial rainfall test as well as physical testing. The results indicate that the risk of soil erosion can be reduced significantly by applying the coal ash which consists of more than 85% of sand to topsoil in the postmine land at the mixing ratio of over 30%. Additionally, they reveal that not only fine fractions but also microporous structures in coal ash enhance water retention capacity by retaining water in the structure, leading to the prevention of soil erosion. Thus, the risk of soil erosion can be reduced by applying coal ash to topsoil in consideration of soil composition and microporous structure of coal ash.

  10. Possibilities of utilizing power plant fly ashes

    Directory of Open Access Journals (Sweden)

    Mezencevová Andrea

    2003-09-01

    Full Text Available The burning of fossil fuels in industrial power stations plays a significant role in the production of thermal and electrical energy. Modern thermal power plants are producing large amounts of solid waste, mainly fly ashes. The disposal of power plant waste is a large environmental problem at the present time. In this paper, possibilities of utilization of power plant fly ashes in industry, especially in civil engineering, are presented. The fly ash is a heterogeneous material with various physical, chemical and mineralogical properties, depending on the mineralogical composition of burned coal and on the used combustion technology. The utilization of fly ashes is determined of their properties. The fineness, specific surface area, particle shape, density, hardness, freeze-thaw resistance, etc. are decisive. The building trade is a branch of industry, which employs fly ash in large quantities for several decades.The best utilization of fluid fly ashes is mainly in the production of cement and concrete, due to the excellent pozzolanic and cementitious properties of this waste. In the concrete processing, the fly ash is utilized as a replacement of the fine aggregate (fine filler or a partial replacement for cement (active admixture. In addition to economic and ecological benefits, the use of fly ash in concrete improves its workability and durability, increases compressive and flexural strength, reduces segregation, bleeding, shrinkage, heat evolution and permeability and enhances sulfate resistance of concrete.The aim of current research is to search for new technologies for the fly ash utilization. The very interesting are biotechnological methods to recovery useful components of fly ashes and unconventional methods of modification of fly ash properties such as hydrothermal zeolitization and mechanochemical modification of its properties. Mechanochemistry deals with physico - chemical transformations and chemical reactions of solids induced by

  11. The Environmental Impacts of Power Plants in Kosovo and Sustainable Development

    OpenAIRE

    , I. Ramadani; , F. Isufi; , S. Bulliqi; , G. Gashi; , A. Ejupi; , V. Bytyqi

    2011-01-01

    Coal represents a strategic importance for energy production and economic development of Kosovo; however, environmental effects are evident during its use. Currently, coal is the main source for electricity production in Kosovo. The uses of lignite from open mines and ash dumps have created a new landscape (degraded) in considerable area. During the processes of energy production from emission of gases, ash, toxic metals, there is seriously threatened a considerable part of territory where li...

  12. Minerals in the Ash and Slag from Oxygen-Enriched Underground Coal Gasification

    Directory of Open Access Journals (Sweden)

    Shuqin Liu

    2016-03-01

    Full Text Available Underground coal gasification (UCG is a promising option for the recovery of low-rank and inaccessible coal resources. Detailed mineralogical information is essential to understand underground reaction conditions far from the surface and optimize the operation parameters during the UCG process. It is also significant in identifying the environmental effects of UCG residue. In this paper, with regard to the underground gasification of lignite, UCG slag was prepared through simulation tests of oxygen-enriched gasification under different atmospheric conditions, and the minerals were identified by X-Ray diffraction (XRD and a scanning electron microscope coupled to an energy-dispersive spectrometer (SEM-EDS. Thermodynamic calculations performed using FactSage 6.4 were used to help to understand the transformation of minerals. The results indicate that an increased oxygen concentration is beneficial to the reformation of mineral crystal after ash fusion and the resulting crystal structures of minerals also tend to be more orderly. The dominant minerals in 60%-O2 and 80%-O2 UCG slag include anorthite, pyroxene, and gehlenite, while amorphous substances almost disappear. In addition, with increasing oxygen content, mullite might react with the calcium oxide existed in the slag to generate anorthite, which could then serve as a calcium source for the formation of gehlenite. In 80%-O2 UCG slag, the iron-bearing mineral is transformed from sekaninaite to pyroxene.

  13. Measurement of natural activity in peat ashes

    International Nuclear Information System (INIS)

    Suomela, J.

    1985-01-01

    High proportions of radioactive materials in peat ashes may involve radiation hazards during handling and deposition of these waste materials. Measurements have been performed to determine the content of radioactive materials in ashes from peat burning. The activities in fly ash and ''solid'' ash in seven peat-fired power plants in Sweden are presented. The methods of analysing and measuring peat ashes for activity from different radionuclides are described. The activity levels in ash samples are given

  14. Classification of pulverized coal ash

    International Nuclear Information System (INIS)

    Van der Sloot, H.A.; Van der Hoek, E.E.; De Groot, G.J.; Comans, R.N.J.

    1992-09-01

    The leachability of fifty different pulverized coal ashes from utilities in the Netherlands, Federal Republic of Germany and Belgium has been studied. Five different ashes were analyzed according to the complete standard leaching test and the results were published earlier. The examination of a wide variety of ashes under a wide range of pH and Liquid to Solid ratio (LS) conditions creates the possibility of identifying systematic trends in fly ash leaching behaviour and to identify the mechanisms controlling release. 16 figs., 2 tabs., 3 app., 25 refs

  15. Radioactivity of wood ash; Puun tuhkan radioaktiivisuus

    Energy Technology Data Exchange (ETDEWEB)

    Rantavaara, A.; Moring, M

    2000-01-01

    STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg{sup -1}, in decreasing order: {sup 137}Cs, {sup 40}K, {sup 90}Sr, {sup 210}Pb,{sup 226}Ra, {sup 232}Th, {sup 134}Cs, {sup 235}U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and {sup 210}Pb was hardly detectable. The NH{sub 4}Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

  16. An improved ashing procedure for biologic sample

    Energy Technology Data Exchange (ETDEWEB)

    Zongmei, Wu [Zhejiang Province Enviromental Radiation Monitoring Centre (China)

    1992-07-01

    The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches.

  17. An improved ashing procedure for biologic sample

    International Nuclear Information System (INIS)

    Wu Zongmei

    1992-01-01

    The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches

  18. Treatment of fly ash for use in concrete

    Science.gov (United States)

    Boxley, Chett [Park City, UT

    2012-05-15

    A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

  19. Engineering properties of fly ash concrete

    International Nuclear Information System (INIS)

    Hilmi Mahmud

    1999-01-01

    This paper presents some of the engineering properties of Malaysian fly ash concrete. Workability, compressive, flexural, tensile splitting, drying shrinkage, elastic modulus and non destructive tests were performed on fly ash and control OPC concrete specimens. Data show that concrete containing 25% fly ash replacement of cement exhibit superior or similar engineering properties to that normal concrete without fly ash. These encouraging results demonstrated the technical merits of incorporating fly ash in concrete and should pave the way for wide scale use of this versatile material in the Malaysian construction industry. (author)

  20. Treatment of fly ash for use in concrete

    Science.gov (United States)

    Boxley, Chett; Akash, Akash; Zhao, Qiang

    2013-01-08

    A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with an activator solution sufficient to initiate a geopolymerization reaction and for a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 35% of the foam index of the untreated fly ash, and in some cases less than 10% of the foam index of the untreated fly ash. The activator solution may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

  1. Gasification of high ash, high ash fusion temperature bituminous coals

    Science.gov (United States)

    Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

    2015-11-13

    This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

  2. Late Neogene leaf assemblage from Bełchatów Lignite Mine (central Poland

    Directory of Open Access Journals (Sweden)

    Worobiec Grzegorz

    2014-12-01

    Full Text Available Leaf macroremains collected in the Bełchatów Lignite Mine (central Poland were investigated. The fossil assemblage consists of leaves of Acer, Betula, Carpinus, Dicotylophyllum, Fagus, ?Magnolia, “Parrotia”, Pinus, Quercus, and Zelkova. Mesophytic (zonal elements dominate, with admixture of riparian (azonal leaf taxa. The floristic composition points to late Neogene (late Miocene to late Pliocene age and suggests favourable temperate climate with mild winters.

  3. Determining the ash content of coal flotation tailings using an MPOF optical ash meter

    Energy Technology Data Exchange (ETDEWEB)

    Sikora, T; Sliwa, J

    1982-01-01

    The block layout, a description of the design and principles of operation of an automatic optical, continuous action MPOF type ash meter are presented. The difference in the optical properties of coal and rock is used in the ash meter. The identification of the ash content is conducted on the basis of the spectral characteristics of reflection of a finely dispersed aqueous coal and rock suspension.

  4. Analysis of the effects of biomass on the co-pyrolysis of coal using TGA method

    International Nuclear Information System (INIS)

    Yaman, S.; Haykiri-Acma, H.

    2009-01-01

    Turkey is a developing country with a population of 7.15 million and its economy is the 16th biggest in the world and 7th biggest in Europe (after Germany, United Kingdom, France, Italy, Spain, and Russia) with a Gross Domestic Product (GDP) of about 700 billion dollar. Low quality lignitic coals are the most significant primary energy resources of Turkey. Consequently, production of lignite in 2007 is 72 million tons, representing about 7.5% of lignite consumption of the world. However, undesirable characteristics of these lignites such as low calorific value, high ash, and high sulfur are some of serious drawbacks in the usage of them in conventional burning systems, regarding problematic deposit formations and polluting emissions. Therefore, alternative processes for these lignites such as pyrolysis and gasification to produce fuel gases and chemical are preferable. In this study, co-pyrolysis characteristics of Afsin-Elbistan lignite with biomass species such as hazelnut shells, sunflower seed shells, and hybrid poplar were investigated by Non-isothermal Thermogravimetry (TGA) technique. Structural differences in the physical and chemical properties of the samples were studied applying some methods such as X-Ray Diffractometry and Scanning Electron Microscopy. This study showed that addition of such biomass materials into lignite and then co-pyrolysis of these mixtures led to conversion levels that are seriously higher than the conversion level of the lignite alone under the same pyrolytic conditions. It is concluded that there are evident differences between the thermal reactivities of the lignite and the biomass materials, and the increase in the thermal reactivity when biomass was introduced may be explained by synergistic interactions between the constituents of lignite and biomass. (author)

  5. Electrodialytic removal of heavy metals from fly ashes

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul

    2002-01-01

    The aim of the Ph.D. work was to develop the electrodialytic remediation method for removal of heavy metals from fly ashes. The work was focused on two types of fly ashes: fly ashes from wood combustion and fly ashes from municipal solid waste incineration.......The aim of the Ph.D. work was to develop the electrodialytic remediation method for removal of heavy metals from fly ashes. The work was focused on two types of fly ashes: fly ashes from wood combustion and fly ashes from municipal solid waste incineration....

  6. Device for determining element contents of lignite mass flows by activation analysis

    International Nuclear Information System (INIS)

    Goeldner, R.; Maul, E.; Rose, W.; Wagner, D.

    1987-01-01

    A simple device is presented, apt for continuous operation, to determine the element contents of bulk goods of flowable materials with a suitable granularity, in particular of lignite mass flows to assess the coal quality. Several kilograms of samples can be reproducibly dosed and homogeneously activated by a device consisting of a shielding container with activation chamber and radiation source, a measuring unit with detectors, and a source container, and characterized by a blade wheel in the activation chamber which causes the dosing and homogeneous activation of the sample

  7. Utilization options for fly ash, bottom ash, and slag in Eastern Europe

    Energy Technology Data Exchange (ETDEWEB)

    Manz, O.E.

    1995-12-01

    Since 1967, at least six ash utilization symposiums have been held in the United States, with papers presented by several European authors on the utilization of coal by-products in Eastern Europe. There is currently over 80,000 megawatts of installed coal-fired capacity available in that region. Unfortunately, of the 117,778,000 tonnes of fly ash, bottom ash, and slag produced in Eastern Europe in 1989, only 13% was utilized. This paper outlines the research and levels and kinds of coal by-product utilization taking place in Eastern Europe since the late 1960s.

  8. Ash fusion temperatures and the transformations of coal ash particles to slag

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.; Wall, T.F.; Creelman, R.A.; Gupta, R. [Univ. of Newcastle, Callaghan (Australia)

    1996-12-31

    A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degrees}C. The temperatures corresponding to the rapid rate of shrinkage are shown to correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined with an SEM to identify the associated chemical and physical changes. The progressive changes in the range of chemical analysis (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenization, viscosity and ash fusion mechanisms.

  9. Ash fusion temperatures and the transformations of coal ash particles to slag

    Energy Technology Data Exchange (ETDEWEB)

    Wall, T.F.; Creelman, R.A.; Gupta, R.; Gupta, S. [Univ. of Newcastle (Australia)

    1996-10-01

    A mechanistic study is detailed in which coal ash is heated with the shrinkage and electrical resistance measured continuously up to a temperature of 1600{degrees}C. The temperatures corresponding to rapid rates of shrinkage are shown to correspond to the formation of eutectics identified on phase diagrams. Samples where therefore heated to these temperatures, cooled rapidly and examined with an SEM to identify the associated chemical and physical changes. The progressive changes in the range of chemical analysis (from SEM), the extent of undissolved ash particles and porosity are then quantified and related to the shrinkage events and standard ash fusion temperatures.

  10. Lignite air-steam gasification in the fluidized bed of iron-containing slag catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, B.N.; Shchipko, M.L.; Golovin, Yu. [Inst. of Chemistry of Natural Organic Materials, Academgorodok, Krasnoyarsk (Russian Federation)

    1995-12-01

    The influence of fluidized bed of iron-containing slag particles on air-steam gasification of powdered Kansk-Achinsk lignite in entrained flow was studied in pilot installation with productivity about 60 kg per hour. Slag of Martin process and boiler slag were used as catalytic active materials until their complete mechanical attrition. Two following methods of catalytic gasification of lignite were compared: the partial gasification in stationary fluidized bed of slag particles with degree of fuel conversion 40-70% and complete gasification in circulating bed of slag particles. In the first case only the most reactive part of fuel is gasified with the simultaneously formation of porous carbon residue with good sorption ability. It was found the catalytic fluidized bed improves heat transfer from combustion to reduction zone of gas-generator and increases the rate of fuel conversion at the temperature range 900-1000{degrees}C. At these temperatures the degree of conversion is depended considerably on the duration time of fuel particles in the catalytic fluidized bed. The influence of catalytic fluidized bed height and velocity of reaction mixture on the temperature profiles in the gas-generator was studied. The optimal relationship was found between the fluidized bed height and velocity of flow which makes possible to produce the gas with higher calorific value at maximum degree of fuel conversion.

  11. Environmental policy instruments towards lignite-fired power plants in Turkey

    International Nuclear Information System (INIS)

    2006-01-01

    A proposition is made that Turkey considers a pilot emission trading system for SO 2 , Nox and/or PM emissions from its coal and lignite fired power plant in the efforts to comply with the EU Integrated Pollution Prevention Control (IPPC), the Large Combustion Plant (LCP) and the National Emissions Ceiling (NEC) Directives. Model calculations indicate that this could yield substantial cost savings compared to a traditional command and control approach. However, requirements in the IPPC Directive would be a major obstacle against emissions trading. The Turkish emission permitting system needs a major overhaul, including improving monitoring and enforcement practices to comply with the directives and to be able to implement and operate an emission trading system

  12. Environmental policy instruments towards lignite-fired power plants in Turkey

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    A proposition is made that Turkey considers a pilot emission trading system for SO{sub 2}, Nox and/or PM emissions from its coal and lignite fired power plant in the efforts to comply with the EU Integrated Pollution Prevention Control (IPPC), the Large Combustion Plant (LCP) and the National Emissions Ceiling (NEC) Directives. Model calculations indicate that this could yield substantial cost savings compared to a traditional command and control approach. However, requirements in the IPPC Directive would be a major obstacle against emissions trading. The Turkish emission permitting system needs a major overhaul, including improving monitoring and enforcement practices to comply with the directives and to be able to implement and operate an emission trading system.

  13. Ecotoxicological relations on a large pig fattening farm located in a lignite mining area and near a solid fuel power plant

    Energy Technology Data Exchange (ETDEWEB)

    Raszyk, J.; Docekalova, H.; Rubes, J.; Gajduskova, V.; Masek, J.; Rodak, L.; Bartos, J. (Veterinary Research Institute, Brno (Czechoslovakia))

    1992-01-01

    Major contaminants identified in 1983-1984 on a pig fattening farm located in a lignite mining area and near a solid fuel power plant, were mercury, cadmium, lead, chromium and aflatoxin B1. Feed samples were collected to assess the contamination load at feed uptake. Permissible concentrations of mercury, chromium, cadmium, aflatoxin B1, lead and atrazin in the feed were exceeded in 56, 50, 31, 19, 6 and 6% samples, respectively. Permissible concentrations of mercury, cadmium and lead in porcine muscles were exceeded in 65, 51, 24% samples, respectively. Pigs fattened in the contaminated environment (i.e. fed contaminated feed mixtures, inspiring contaminated dust and absorbing percutaneously contaminants from dust deposits on the body surface) showed: (1) impairment of the genetic apparatus; (2) a certain degree of immunosuppression; (3) higher feed consumption per 1 kg weight gain and lower average daily weight gain; (4) increased incidence of health disorders. The authors were not allowed to analyse ash and solid emissions from the power plant. Therefore the share of the emissions in the overall environmental contamination on the fattening farm could not be quantified. The personnel, working in the contaminated environment for a prolonged period, are endangered most of all by stable dust, being exposed to its mechanical, chemical, allergic and infectious effects. Consumption of meat and organs from pigs fattened in a contaminated environment is associated with the risk of an increased uptake of various contaminants.

  14. Hazards Associated With Recent Popocatepetl Ash Emissions

    Science.gov (United States)

    Nieto, A.; Martin, A.; Espinasa-Pereña, R.; Ferres, D.

    2013-05-01

    Popocatepetl has been producing ash from small eruptions since 1994. Until 2012 about 650 small ash emissions have been recorded at the monitoring system of Popocatépetl Volcano. Ash consists mainly of glassy lithic clasts from the recent crater domes, plagioclase and pyroxene crystals, and in major eruptions, olivine and/or hornblende. Dome forming eruptions produced a fine white ash which covers the coarser ash. This fine ash consists of plagioclase, glass and cristobalite particles mostly under15 microns. During the recent crisis at Popocatépetl, April and May2012 ash fell on villages to the east and west of the volcano, reaching Mexico City (more than 20 million people) and Puebla (2 million people). In 14 cases the plumes had heights over 2 km, the largest on May 2 and 11 (3 and 4 km in height, respectively). Heavier ash fall occurred on April 13, 14, 20, and 23 and May 2, 3, 5, 11, 14, 23, 24 and 25. A database for ash fall was constructed from April 13 with field observations, reports emitted by the Centro Nacional de Comunicaciones (CENACOM), ash fall advisories received at CENAPRED and alerts from the Servicios a la Navegación en el Espacio Aéreo Mexicano (SENEAM). This aim of this database is to calculate areas affected by the ash and estimate the ash fall volume emitted by Popocatépetl in each of these events. Heavy ash fall from the May 8 to May 11 combined with reduced visibility due to fog forced to closure of the Puebla airport during various periods of time, for up to 13 hours. Domestic and international flights were cancelled. Ash eruptions have caused respiratory conditions in the state of Puebla, to the east of the volcano, since 1994 (Rojas et al, 2001), but because of the changing wind conditions in the summer mainly, some of these ash plumes go westward to towns in the State of Mexico and even Mexico City. Preliminary analyses of these eruptions indicate that some ash emissions produced increased respiratory noninfectious problems

  15. Bucket wheel excavator performances at Neyveli lignite mine

    Energy Technology Data Exchange (ETDEWEB)

    Kumaraswamy, S; Mozumdar, B K

    1987-03-01

    Bucket-wheel excavators have been in use at the Neyveli Lignite Mine in the State of Tamil Nadu, India, since the early nineteen-sixties. The mining environment has been particularly harsh for BWE application. The adverse influencing factors are the hardness of the over-burden formation, high abrasivity of rock and artesian ground water conditions. In this paper, the performances of the BWEs at Neyveli have been statistically analysed to determine the effects of physico-mechanical properties of overburden, blasting and rainfall on machine productivity, availability, wear-and-tear of bucket teeth, power consumption, production efficiency and cost of mining. An empirical relationship between the production efficiency, defined as the ratio of actual production rate to the theoretical one, and the bench height and width, height of slices, specific cutting resistance of the overburden material and its clay content, consumption of explosives, and conveyor length has been established.

  16. Analysis list: ash2 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ash2 Larvae + dm3 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2.1.tsv ...http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2.5.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2....10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/colo/ash2.Larvae.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/colo/Larvae.gml ...

  17. Attraction of the emerald ash borer to ash trees stressed by girdling, herbicide treatment, or wounding

    Science.gov (United States)

    Deborah McCullough; Therese Poland; David. Cappaert

    2009-01-01

    New infestations of emerald ash borer, Agrilus planipennis Fairmaire, an invasive pest native to Asia, are difficult to detect until densities build and symptoms appear on affected ash (Fraxinus spp). We compared the attraction of A. planipennis to ash trees stressed by girdling (bark and phloem removed...

  18. Ash in fire affected ecosystems

    Science.gov (United States)

    Pereira, Paulo; Jordan, Antonio; Cerda, Artemi; Martin, Deborah

    2015-04-01

    Ash in fire affected ecosystems Ash lefts an important footprint in the ecosystems and has a key role in the immediate period after the fire (Bodi et al., 2014; Pereira et al., 2015). It is an important source of nutrients for plant recover (Pereira et al., 2014a), protects soil from erosion and controls soil hydrological process as runoff, infiltration and water repellency (Cerda and Doerr, 2008; Bodi et al., 2012, Pereira et al., 2014b). Despite the recognition of ash impact and contribution to ecosystems recuperation, it is assumed that we still have little knowledge about the implications of ash in fire affected areas. Regarding this situation we wanted to improve our knowledge in this field and understand the state of the research about fire ash around world. The special issue about "The role of ash in fire affected ecosystems" currently in publication in CATENA born from the necessity of joint efforts, identify research gaps, and discuss future cooperation in this interdisciplinary field. This is the first special issue about fire ash in the international literature. In total it will be published 10 papers focused in different aspects of the impacts of ash in fire affected ecosystems from several parts of the world: • Fire reconstruction using charcoal particles (Burjachs and Espositio, in press) • Ash slurries impact on rheological properties of Runoff (Burns and Gabet, in press) • Methods to analyse ash conductivity and sorbtivity in the laboratory and in the field (Balfour et al., in press) • Termogravimetric and hydrological properties of ash (Dlapa et al. in press) • Effects of ash cover in water infiltration (Leon et al., in press) • Impact of ash in volcanic soils (Dorta Almenar et al., in press; Escuday et al., in press) • Ash PAH and Chemical extracts (Silva et al., in press) • Microbiology (Barreiro et al., in press; Lombao et al., in press) We believe that this special issue will contribute importantly to the better understanding of

  19. Research of lignite oxidation kinetic parameters modified by CuSO4 and NaNO3 initiation additives

    Directory of Open Access Journals (Sweden)

    Larionov Kirill

    2017-01-01

    Full Text Available An experimental study and subsequent analytical assessment of activation energy change in lignite oxidation process with addition of NaNO3 and CuSO4 mineral salts were conducted. The results showed that injection of catalytic additives leads to reduction of coal activation energy and reaction initial temperature.

  20. REMOVAL OF Cr(VI FROM AQUEOUS SOLUTION BY ACTIVATED COAL FROM LIGNITE COAL

    Directory of Open Access Journals (Sweden)

    Mehmet MAHRAMANLIOĞLU

    2001-03-01

    Full Text Available Activated coal produced from Ağaçlı Lignite coal was used to remove Cr(VI from aqueous solutions. The adsorption of Cr(VI was studied as a function of initial concentration, time, pH, adsorbent concentration and temperature. The adsorption data were found to fit to Langmuir and Freundlich isotherms. Lagergren equation was used to calculate the adsorption rate. The amount of Cr(VI adsorbed was increased with decreasing pH and decreased with increasing temperature.

  1. Modernisation of a lignite-fired steam generator. Reduction of NO{sub x} emission

    Energy Technology Data Exchange (ETDEWEB)

    Kriegeskotte, Ralf; Thierbach, Hans-Ulrich; Zimmermann, Bernhard [Steinmueller Engineering GmbH, Gummersbach (Germany); Di Ferdinando, Quinto [ContourGlobal Maritsa East 3 AD, Sofia (Bulgaria)

    2013-11-01

    ContourGlobal Maritsa East 3 is a lignite-fired power plant with an electrical total output of 4 x 227 MW. The four steam generators of Russian design have a steam capacity up to 730 t/h each and were commissioned between 1978 and 1981. According to EU requirements, the NO{sub x} emissions have to be reduced reliably by 2015. The consortium Steinmueller Engineering GmbH Gummersbach and Siemens EOOD, Sofia, successfully redesigned the furnace of boiler 4. (orig.)

  2. Formation and utilization of fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Vargyai, J

    1974-01-01

    General problems of slag and fly ash formation and utilization are discussed. The ever-increasing energy demand, and the comeback of coal as an energy carrier in power plants call for efficient solutions to the problem of slag and fly ash. Slag and fly ash are used for concrete in which they partly replace cement. Other possible uses are the amelioration of acid soils, fireclay manufacture, road construction, and tiles. It is possible to recover metals, such as vanadium, iron, aluminum, and radioactive materials from certain types of fly ash and slag. The utilization of fly ash is essential also with respect to the abatement of entrainment from dumps.

  3. The influence of using volcanic ash and lime ash as filler on compressive strength in self compacting concrete

    Science.gov (United States)

    Karolina, Rahmi; Panatap Simanjuntak, Murydrischy

    2018-03-01

    Self Compacting Concrete (SCC) is a technology which is developing today in which concrete solidifies by itself without using vibrator. Casting conventional concrete which has a lot of reinforcement bars sometimes finds difficulty in achieving optimal solidity. The method used to solve this problem is by using SCC technology. SCC was made by using filler, volcanic ash, and lime ash as the filling materials so that the concrete became more solid and hollow space could be filled up. The variation of using these two materials was 10%, 15%, 20%, and 25% of the cementitious mass and using 1% of superplasticizer from cementitious material. The supporting testing was done by using the test when the concrete was still fluid and when it was solid. Malleable concrete was tested by using EFNARC 2002 standard in slump flow test, v-funnel test, l-shaped box test, and j-ring test to obtain filling ability and passing ability. In this malleable lime concrete test, there was the decrease, compared with normal SCC concrete without adding volcanic ash and lime ash. Testing was also done in solid concrete in compressive strength, tensile strength, and concrete absorption. The result of the testing showed that the optimum tensile strength in Variation 1, without volcanic ash and lime ash – with 1% of superplasticizer was 39.556 MPa, the optimum tensile strength in Variation 1, without volcanic ash and lime ash- with 1% of super-plasticizer was 3.563 MPa, while the value of optimum absorption which occurred in Variation 5 (25% of volcanic ash + 25% of lime ash + 50% of cement + 1% of superplasticizer) was 1.313%. This was caused by the addition of volcanic ash and lime ash which had high water absorption.

  4. Evaluation of the Chemical and Mechanical Properties of Hardening High-Calcium Fly Ash Blended Concrete.

    Science.gov (United States)

    Fan, Wei-Jie; Wang, Xiao-Yong; Park, Ki-Bong

    2015-09-07

    High-calcium fly ash (FH) is the combustion residue from electric power plants burning lignite or sub-bituminous coal. As a mineral admixture, FH can be used to produce high-strength concrete and high-performance concrete. The development of chemical and mechanical properties is a crucial factor for appropriately using FH in the concrete industry. To achieve sustainable development in the concrete industry, this paper presents a theoretical model to systematically evaluate the property developments of FH blended concrete. The proposed model analyzes the cement hydration, the reaction of free CaO in FH, and the reaction of phases in FH other than free CaO. The mutual interactions among cement hydration, the reaction of free CaO in FH, and the reaction of other phases in FH are also considered through the calcium hydroxide contents and the capillary water contents. Using the hydration degree of cement, the reaction degree of free CaO in FH, and the reaction degree of other phases in FH, the proposed model evaluates the calcium hydroxide contents, the reaction degree of FH, chemically bound water, porosity, and the compressive strength of hardening concrete with different water to binder ratios and FH replacement ratios. The evaluated results are compared to experimental results, and good consistencies are found.

  5. Wildfire Ash: Chemical Composition, Ash-Soil Interactions and Environmental Impacts

    Science.gov (United States)

    Brook, Anna; Hamzi, Seham; Wittenberg, Lea

    2015-04-01

    Of the five classical factors of soil formation, climate, parent material, topography, time, organisms, and recently recognized human activity, it is the latter factor which discretely includes fire and post-burn impact. However, it is considered that soil undergoing fire just experience a temporary removal of the top organic horizon, thus slightly modified and often labeled as 'temporarily disturbed' soil or soil 'under restoration/rehabilitation'. In fact the suggested seventh factor, post-burned produced ash, can act both dependently and independently of the other soil forming factors (Levin et al., 2013; Certini 2013). They are interdependent in cases where ash influences occur on time scales similar to 'natural' soil formation (Keesstra et ai., 2014) such as changes in vegetation. On the other hand, in post-fire areas a strong dependency is expected between soil-water retention mechanism, climate and topography. Wild-land fires exert many changes on the physical, chemical, mineralogical, biological, and morphological properties of soil that, in turn, affect the soil's hydrology and nutrient flux, modifying its ability to support vegetation and resist erosion. The ash produced by forest fires is a complex mixture composed of organic and inorganic particles characterized by vary physical-chemical and morphological properties. The importance of this study is straightforwardly related to the frequency and large-scales wildfires in Mediterranean region. In fact, wildfires are major environmental and land management concern in the world, where the number and severity of wildfires has increased during the past decades (Bodi, 2013). Certini (2013) assumed that cumulatively all of the vegetated land is burned in about 31 years annually affecting 330-430 Mha (over 3% of the Earth's surface) and wide range of land cover types worldwide including forests, peatlands, shrublands and grasslands. Whereas, the fire is identified as an important factor in soil formation, the

  6. Associative properties of 137Cs in biofuel ashes

    International Nuclear Information System (INIS)

    Ravila, A.; Holm, E.

    1999-01-01

    The present study aims to reveal how radiocesium is associated to the ash particles derived from biofuel combustion. A sequential extraction procedure was carried out for the characterisation of radiocesium speciation in ash generated by different fuels and burner types. The ash types considered were fly ash and bottom ash collected from Swedish district heating plants using bark wood or peat as fuel. A fraction of the radiocesium in biofuel ash can easily become solubilised and mobilised by water and also, a significant fraction of the radionuclides can be bound to the ash particles in cation-exchangeable forms. Therefore, at using the ash derived from biofuels to recycle mineral nutrients for forestry or short rotation coppicing, radiocesium solubilised and leached from the ash by rains has a potential to rather quickly enter the rooting zone of forest vegetation or energy crops. On the other hand, radiocesium strongly bound to the ash will migrate slowly into the soil column with the successive accumulation of litter and in the process act to maintain the external dose rate at an elevated level for a long time. The results of the sequential extraction procedure and activity determination of the different extracted fractions implies that the bioavailable fraction of radiocesium in ash from bark, wood or peat is in the range between 20-85% of the total ash contents. Peat ash collected from a powder burner strongly retained a large fraction (70-90%) of its radiocesium content while the peat ash from a continuos fluidized bed type burner retained nearly 100% of the radiocesium in the bottom ash and only about 15% in the fly ash

  7. Indirect effects of emerald ash borer-induced ash mortality and canopy gap formation on epigaeic beetles.

    Science.gov (United States)

    Gandhi, Kamal J K; Smith, Annemarie; Hartzler, Diane M; Herms, Daniel A

    2014-06-01

    Exotic herbivorous insects have drastically and irreversibly altered forest structure and composition of North American forests. For example, emerald ash borer (Agrilus planipennis Fairmaire) from Asia has caused wide-scale mortality of ash trees (Fraxinus spp.) in eastern United States and Canada. We studied the effects of forest changes resulting from emerald ash borer invasion on epigaeic or ground beetles (Coleoptera: Carabidae) along a gradient of ash dieback and gap sizes in southeastern Michigan. Ground beetles were sampled in hydric, mesic, and xeric habitats in which black (Fraxinus nigra Marshall), green (Fraxinus pennsylvanica Marshall), and white (Fraxinus americana L.) ash were the most common species, respectively. During 2006-2007, we trapped 2,545 adult ground beetles comprising 52 species. There was a negative correlation between percent ash tree mortality in 2006 and catches of all beetles. Catches of Agonum melanarium Dejean (in 2006) and Pterostichus mutus (Say) (in 2006-2007) were negatively correlated with tree mortality and gap size, respectively. However, catches of Pterostichus corvinus Dejean were positively correlated with gap size in 2006. As ash mortality and average gap size increased from 2006 to 2007, catches of all beetles as well as P. mutus and Pterostichus stygicus (Say) increased (1.3-3.9 times), while species diversity decreased, especially in mesic and xeric stands. Cluster analysis revealed that beetle assemblages in hydric and mesic stand diverged (25 and 40%, respectively) in their composition from 2006 to 2007, and that hydric stands had the most unique beetle assemblages. Overall, epigaeic beetle assemblages were altered in ash stands impacted by emerald ash borer; however, these impacts may dissipate as canopy gaps close.

  8. An ecosystem approach to evaluate restoration measures in the lignite mining district of Lusatia/Germany

    Science.gov (United States)

    Schaaf, Wolfgang

    2015-04-01

    Lignite mining in Lusatia has a history of over 100 years. Open-cast mining directly affected an area of 1000 km2. Since 20 years we established an ecosystem oriented approach to evaluate the development and site characteristics of post-mining areas mainly restored for agricultural and silvicultural land use. Water and element budgets of afforested sites were studied under different geochemical settings in a chronosequence approach (Schaaf 2001), as well as the effect of soil amendments like sewage sludge or compost in restoration (Schaaf & Hüttl 2006). Since 10 years we also study the development of natural site regeneration in the constructed catchment Chicken Creek at the watershed scale (Schaaf et al. 2011, 2013). One of the striking characteristics of post-mining sites is a very large small-scale soil heterogeneity that has to be taken into account with respect to soil forming processes and element cycling. Results from these studies in combination with smaller-scale process studies enable to evaluate the long-term effect of restoration measures and adapted land use options. In addition, it is crucial to compare these results with data from undisturbed, i.e. non-mined sites. Schaaf, W., 2001: What can element budgets of false-time series tell us about ecosystem development on post-lignite mining sites? Ecological Engineering 17, 241-252. Schaaf, W. and Hüttl, R. F., 2006: Direct and indirect effects of soil pollution by lignite mining. Water, Air and Soil Pollution - Focus 6, 253-264. Schaaf, W., Bens, O., Fischer, A., Gerke, H.H., Gerwin, W., Grünewald, U., Holländer, H.M., Kögel-Knabner, I., Mutz, M., Schloter, M., Schulin, R., Veste, M., Winter, S. & Hüttl, R.F., 2011: Patterns and processes of initial terrestrial-ecosystem development. Journal of Plant Nutrition and Soil Science, 174, 229-239. Schaaf, W., Elmer, M., Fischer, A., Gerwin, W., Nenov, R., Pretsch, H. and Zaplate, M.K., 2013: Feedbacks between vegetation, surface structures and hydrology

  9. Review of ecosystem level impacts of emerald ash borer on black ash wetlands: What does the future hold?

    Science.gov (United States)

    Randall K. Kolka; Anthony W. D' Amato; Joseph W. Wagenbrenner; Robert A. Slesak; Thomas G. Pypker; Melissa B. Youngquist; Alexis R. Grinde; Brian J. Palik

    2018-01-01

    The emerald ash borer (EAB) is rapidly spreading throughout eastern North America and devastating ecosystems where ash is a component tree. This rapid and sustained loss of ash trees has already resulted in ecological impacts on both terrestrial and aquatic ecosystems and is projected to be even more severe as EAB invades black ash-dominated wetlands of the western...

  10. Variation in the Volatile Profiles of Black and Manchurian Ash in Relation to Emerald Ash Borer Oviposition Preferences.

    Science.gov (United States)

    Rigsby, Chad M; McCartney, Nathaniel B; Herms, Daniel A; Tumlinson, James H; Cipollini, Don

    2017-08-01

    Emerald ash borer (EAB; Agrilus planipennis) is a devastating pest of ash (Fraxinus spp.) in its invaded range in North America. Its coevolved Asian hosts are more resistant and less preferred for oviposition than susceptible North American species. We compared EAB oviposition preferences and bark and canopy volatile organic compound (VOC) emissions of resistant Manchurian ash and susceptible black ash, and examined relationships between VOC profiles and oviposition. In the field, black ash was highly preferred for oviposition while no eggs were laid on Manchurian ash, and we found clear differences in the VOC profiles of Manchurian and black ash. We detected 78 compounds emitted from these species, including 16 compounds that elicited EAB antennal activity in prior studies. Four compounds were unique to black and 11 to Manchurian ash. Emission rates of 14 canopy and 19 bark volatiles varied among the two species, including four previously reported as antennally active. Specifically, 7-epi-sesquithujene (bark) emissions were greater from black ash, while β-caryophyllene (canopy), linalool (bark), and α-cubebene (bark) were emitted at higher rates by Manchurian ash. No relationships were found between the emission rate of any single compound or group of compounds (e.g. monoterpenes) suggesting that preference may be based on complex profile combinations. This is the first study to directly compare VOCs of black and Manchurian ash as well as the first to examine bark- and canopy-specific VOCs. The unique bark and canopy VOC profiles of these two species implicates potentially important variation in VOCs between a closely related resistant and susceptible species that provides a foundation for future studies of host preferences of EAB.

  11. Coolside waste management demonstration OCDO grant agreement No. CDO/D-902-9. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Wu, M.; Winschel, R.A. [CONSOL Inc., Library, PA (United States). Research & Development

    1997-10-01

    The objectives of this project were to evaluate the potential utilization in road construction of wastes produced from the Coolside, LIMB (limestone injection multi-stage burner) and FBC (fluidized-bed combustion) processes, and to specify criteria for landfill disposal of waste from the Coolside process. These three processes are considered to be clean coal technologies. The Coolside process involves injecting an aqueous slurry of hydrated lime into the ductwork downstream of the air preheater in a coal-fired boiler. The hydrated lime captures sulfur dioxide from the flue gas producing anhydrous calcium sulfite and calcium sulfate, which are collected along with the unused hydrated lime and fly ash. The LIMB process involves injection of lime or hydrated lime directly into the furnace to capture sulfur dioxide. The waste consists principally of anhydrous calcium sulfate, lime, and fly ash. Both processes were demonstrated successfully at the Edgewater Station of Ohio Edison in Lorrain, OH, from 1989 to 1992. Circulating fluidized-bed combustion (FBC) is a commercial technology which combines steam generation with SO{sub 2} control by burning coal in a circulating bed of limestone. The waste, chemically similar to LIMB waste, is produced by bleed-off of the bed material and by collection of the flue dust. All three processes produce a dry solid waste, which must either be used or disposed of and managed to ensure environmental compliance and economic feasibility. The project was completed in June 1996.

  12. Optimizing Use of Girdled Ash Trees for Management of Low-Density Emerald Ash Borer (Coleoptera: Buprestidae) Populations.

    Science.gov (United States)

    Siegert, Nathan W; McCullough, Deborah G; Poland, Therese M; Heyd, Robert L

    2017-06-01

    Effective survey methods to detect and monitor recently established, low-density infestations of emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), remain a high priority because they provide land managers and property owners with time to implement tactics to slow emerald ash borer population growth and the progression of ash mortality. We evaluated options for using girdled ash (Fraxinus spp.) trees for emerald ash borer detection and management in a low-density infestation in a forested area with abundant green ash (F. pennsylvanica). Across replicated 4-ha plots, we compared detection efficiency of 4 versus 16 evenly distributed girdled ash trees and between clusters of 3 versus 12 girdled trees. We also examined within-tree larval distribution in 208 girdled and nongirdled trees and assessed adult emerald ash borer emergence from detection trees felled 11 mo after girdling and left on site. Overall, current-year larvae were present in 85-97% of girdled trees and 57-72% of nongirdled trees, and larval density was 2-5 times greater on girdled than nongirdled trees. Low-density emerald ash borer infestations were readily detected with four girdled trees per 4-ha, and 3-tree clusters were as effective as 12-tree clusters. Larval densities were greatest 0.5 ± 0.4 m below the base of the canopy in girdled trees and 1.3 ± 0.7 m above the canopy base in nongirdled trees. Relatively few adult emerald ash borer emerged from trees felled 11 mo after girdling and left on site through the following summer, suggesting removal or destruction of girdled ash trees may be unnecessary. This could potentially reduce survey costs, particularly in forested areas with poor accessibility. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by US Government employees and is in the public domain in the US.

  13. Organic geochemistry of the Lower Miocene Oberdorf lignite (Styrian Basin, Austria): its relation to petrography, palynology and the palaeoenvironment

    Energy Technology Data Exchange (ETDEWEB)

    Bechtel, A.; Sachsenhofer, R.F.; Kolcon, I.; Gratzer, R. [Institut fuer Geowissenschaften, Prospektion und Angewandte Sedimentologie, Montanuniversitaet Leoben, Peter-Tunner-Str. 5, A-8700 Leoben (Austria); Otto, A.; Puettmann, W. [Institut fuer Mineralogie-Umweltanalytik, J.W. Goethe-Universitaet, Georg-Voigt-Str. 14, D-60054 a.M. Frankfurt (Germany)

    2002-06-01

    In the Oberdorf trough at the northwestern margin of the Styrian Basin (Austria), an up to 36-m thick Lower Miocene (Ottnangian) lignite seam occurs within the fluvial Koeflach-Voitsberg Formation. Previous results indicate that the lignite originated in a topogenous mire within a wet-forest swamp palaeoenvironment. Differences in soluble organic matter (SOM) yield of borehole samples from the lignite seam are related to free lipids present in plant waxes or resins and the presence of thermally labile polymers indicated by the contents of liptinite macerals (i.e., resinite, suberinite, and liptodetrinite). The n-alkane distribution patterns are dominated by high-molecular weight lipids with marked odd over even predominance, originating from plant waxes. A contribution of algae to the even numbered short-chain lipids, observed in considerable amounts in the footwall sediments is proposed. Terpenoid biomarkers characteristic for conifers and angiosperms were detected, consistent with palynomorphic spectra which are dominated by forest swamp pollen (Taxodiaceae-Cupressaceae) and pollen from plants living in a mixed mesophytic forest. Excellent relationships between higher plant biomarker composition and palynologic data indicate that the organic geochemical results reflect the varying inputs of coniferales vs. angiosperms. The data further imply that cuparene may be used for taxonomical differentiation of coniferales families. Organic geochemical data provide evidence that the content of land plant-derived biomarkers is controlled by the input of resin-rich conifers. Concentrations of hopanoids, dominated by hop-17(21)-ene, generally increase towards the top of the lignite, a section characterised by high extents of aromatisation of triterpenoid biomarkers. The results suggest that the aromatisation of angiosperm-derived biomarkers may be governed by the activity of anaerobic rather than by aerobic bacteria. However, changes in the depositional environment and

  14. Reclamation of a lignite combustion waste disposal site with alders (Alnus sp.): assessment of tree growth and nutrient status within 10 years of the experiment.

    Science.gov (United States)

    Pietrzykowski, Marcin; Woś, Bartłomiej; Pająk, Marek; Wanic, Tomasz; Krzaklewski, Wojciech; Chodak, Marcin

    2018-06-01

    Combustion wastes are characterised by extremely low N contents. Therefore, introduction of nitrogen-fixing species at the first stage of their biological reclamation is required. This paper presents an assessment of the growth parameters of alders (Alnus sp.) 10 years after their introduction to a disposal site of lignite combustion waste in Central Poland. Black (Alnus glutinosa) and grey alders (Alnus incana) were planted directly in the combustion waste. The soil amendment included three variants: control with pure combustion waste, admixture of lignite culm and addition of acid sand. Both alder species displayed good growth parameters comparable to those of alders in natural habitats. However, black alder had better growth parameters, such as stand density index (SDI), diameter at breast height (DBH) and height (H) than grey alder. The lignite amendment exerted a positive effect on tree growth, reflected in a higher SDI and H, whereas the acid sand amendment did not affect any of the growth parameters of the studied alder species. Despite the good growth parameters, the measured N:P and N:K ratios in the alder leaves largely differed from the optimal values indicating insufficient P and K supply at the combustion waste disposal site. This may pose a threat to further development of the introduced tree plantings. The introduction of alders along with the lignite addition into the planting holes seems to be a successful method of combustion waste revegetation.

  15. Volcanic ash dosage calculator: A proof-of-concept tool to support aviation stakeholders during ash events

    Science.gov (United States)

    Dacre, H.; Prata, A.; Shine, K. P.; Irvine, E.

    2017-12-01

    The volcanic ash clouds produced by Icelandic volcano Eyjafjallajökull in April/May 2010 resulted in `no fly zones' which paralysed European aircraft activity and cost the airline industry an estimated £1.1 billion. In response to the crisis, the Civil Aviation Authority (CAA), in collaboration with Rolls Royce, produced the `safe-to-fly' chart. As ash concentrations are the primary output of dispersion model forecasts, the chart was designed to illustrate how engine damage progresses as a function of ash concentration. Concentration thresholds were subsequently derived based on previous ash encounters. Research scientists and aircraft manufactures have since recognised the importance of volcanic ash dosages; the accumulated concentration over time. Dosages are an improvement to concentrations as they can be used to identify pernicious situations where ash concentrations are acceptably low but the exposure time is long enough to cause damage to aircraft engines. Here we present a proof-of-concept volcanic ash dosage calculator; an innovative, web-based research tool, developed in close collaboration with operators and regulators, which utilises interactive data visualisation to communicate the uncertainty inherent in dispersion model simulations and subsequent dosage calculations. To calculate dosages, we use NAME (Numerical Atmospheric-dispersion Modelling Environment) to simulate several Icelandic eruption scenarios, which result in tephra dispersal across the North Atlantic, UK and Europe. Ash encounters are simulated based on flight-optimal routes derived from aircraft routing software. Key outputs of the calculator include: the along-flight dosage, exposure time and peak concentration. The design of the tool allows users to explore the key areas of uncertainty in the dosage calculation and to visualise how this changes as the planned flight path is varied. We expect that this research will result in better informed decisions from key stakeholders during

  16. Proceedings of symposium on ash in North America

    Science.gov (United States)

    Charles H. Michler; Matthew D., eds. Ginzel

    2010-01-01

    Includes 5 papers and 30 abstracts covering topics related to the biology and ecology of the ash species, ash utilization and management, emerald ash borer, and other threats to ash, and genetics and conservation of ash species. A paper titled "Population-level variation of Fraxinus americana L. is influenced by climate...

  17. Factors affecting the survival of ash (Fraxinus spp.) trees infested by emerald ash borer (Agrilus planipennis)

    Science.gov (United States)

    Kathleen S. Knight; John P. Brown; Robert P. Long

    2013-01-01

    Emerald ash borer (Agrilus planipennis) (EAB), an Asian woodboring beetle accidentally introduced in North America, has killed millions of ash (Fraxinus spp.) trees and is spreading rapidly. This study examined the effects of tree- and site-level factors on the mortality of ash trees in stands infested by EAB in OH, USA. Our data...

  18. Use of unwounded ash trees for the detection of emerald ash borer adults: EAB landing behavior

    Science.gov (United States)

    Jordan M. Marshall; Melissa J. Porter; Andrew J. Storer

    2011-01-01

    Incorporation of multiple trapping techniques and sites within a survey program is essential to adequately identify the range of emerald ash borer (EAB) (Agrilus planipennis Fairmaire) infestation. Within natural forests, EAB lands on stick band traps wrapped around girdled ash trees at a rate similar to that on unwounded ash trees. The objective of...

  19. Effects of water availability on emerald ash borer larval performance and phloem phenolics of Manchurian and black ash.

    Science.gov (United States)

    Chakraborty, Sourav; Whitehill, Justin G A; Hill, Amy L; Opiyo, Stephen O; Cipollini, Don; Herms, Daniel A; Bonello, Pierluigi

    2014-04-01

    The invasive emerald ash borer (EAB) beetle is a significant threat to the survival of North American ash. In previous work, we identified putative biochemical and molecular markers of constitutive EAB resistance in Manchurian ash, an Asian species co-evolved with EAB. Here, we employed high-throughput high-performance liquid chromatography with photodiode array detection and mass spectrometry (HPLC-PDA-MS) to characterize the induced response of soluble phloem phenolics to EAB attack in resistant Manchurian and susceptible black ash under conditions of either normal or low water availability, and the effects of water availability on larval performance. Total larval mass per tree was lower in Manchurian than in black ash. Low water increased larval numbers and mean larval mass overall, but more so in Manchurian ash. Low water did not affect levels of phenolics in either host species, but six phenolics decreased in response to EAB. In both ashes, pinoresinol A was induced by EAB, especially in Manchurian ash. Pinoresinol A and pinoresinol B were negatively correlated with each other in both species. The higher accumulation of pinoresinol A in Manchurian ash after attack may help explain the resistance of this species to EAB, but none of the responses measured here could explain increased larval performance in trees subjected to low water availability. © 2013 John Wiley & Sons Ltd.

  20. Review of Ecosystem Level Impacts of Emerald Ash Borer on Black Ash Wetlands: What Does the Future Hold?

    Directory of Open Access Journals (Sweden)

    Randall K. Kolka

    2018-04-01

    Full Text Available The emerald ash borer (EAB is rapidly spreading throughout eastern North America and devastating ecosystems where ash is a component tree. This rapid and sustained loss of ash trees has already resulted in ecological impacts on both terrestrial and aquatic ecosystems and is projected to be even more severe as EAB invades black ash-dominated wetlands of the western Great Lakes region. Using two companion studies that are simulating short- and long-term EAB infestations and what is known from the literature, we synthesize our current limited understanding and predict anticipated future impacts of EAB on black ash wetlands. A key response to the die-back of mature black ash will be higher water tables and the potential for flooding and resulting changes to both the vegetation and animal communities. Although seedling planting studies have shown some possible replacement species, little is known about how the removal of black ash from the canopy will affect non-ash species growth and regeneration. Because black ash litter is relatively high in nitrogen, it is expected that there will be important changes in nutrient and carbon cycling and subsequent rates of productivity and decomposition. Changes in hydrology and nutrient and carbon cycling will have cascading effects on the biological community which have been scarcely studied. Research to address these important gaps is currently underway and should lead to alternatives to mitigate the effects of EAB on black ash wetland forests and develop management options pre- and post-EAB invasion.

  1. Tanacetum vulgare as a bioindicator of trace-metal contamination: a study of a naturally colonized open-pit lignite mine.

    Science.gov (United States)

    Jasion, Mateusz; Samecka-Cymerman, Aleksandra; Kolon, Krzysztof; Kempers, Alexander J

    2013-10-01

    We investigated the possibility of use of Tanacetum vulgare (tansy) as an ecological indicator of metal concentration in a naturally colonized open-pit lignite mine in Bełchatów (Poland). Tanacetum vulgare is the only species growing abundantly and spontaneously in the lignite mine waste dumps. Metal concentrations in roots, stems, leaves, flowers, and soil were measured in dump sites differing in type and time of reclamation and therefore differing in pollution levels. Tanacetum vulgare appeared to be an accumulator of chromium and iron in roots, whereas highest concentrations of manganese and zinc were found in leaves. A high bioaccumulation factor for cadmium (Cd) was observed in dumps and control sites, indicating that even small amounts of Cd in the environment may result in significant uptake by the plant. The lowest concentrations of metals were found in plants from sites situated on dumps reclaimed with argillaceous limestone.

  2. Effect of various experimental parameters on the swelling and supercritical extraction properties of lignite

    Energy Technology Data Exchange (ETDEWEB)

    Hacimehmetoglu, S.; Sinag, A.; Tekes, A.T.; Misirlioglu, Z.; Canel, M. [Ankara University, Ankara (Turkey). Faculty of Science

    2007-07-01

    The original lignite sample, the samples swollen in dimethylsulfoxide (DMSO), dimethylformamide (DMF), pyridine, tetrahydrofuran (THF), acetone, ethylenediamine (EDA), N-methyl-2-pyrrolidone (NMP), tetrabutylammonium hydroxide (TBAH), the samples impregnated by ZnCl{sub 2} as catalyst and the samples both swollen in the solvents and impregnated by ZnCl{sub 2} were subjected to the supercritical toluene extraction and the effects of temperature, pressure, pre-swelling procedure, hydrogen donor solvent (tetralin), and catalyst on the extract yields were investigated.

  3. Softening behaviour of brown coal ashes. Influence of ash components and gas atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Hegermann, R; Huettinger, K J [Karlsruhe Univ. (T.H.) (Germany, F.R.). Inst. fuer Chemische Technik

    1990-03-01

    The softening behaviour of brown coal ashes during gasification is important for three reasons: (1) Formation of large agglomerates, (2) inactivation of catalytically active ash components, (3) encapsulation of parts of the coal. The softening behaviour of the ashes was studied with a high temperature dilatometer at ambient pressure in various atmospheres (air, CO{sub 2}, Ar/H{sub 2}O, Ar, H{sub 2}/H{sub 2}O, H{sub 2}) using a push-rod with a conical tip. The heating rate was 5 Kmin{sup -1}, the final temperature 1000deg C, the residence time 1 h. (orig.).

  4. Drycon dry ash conveyor: dry bottom ash handling system with reduced operating costs and improved plant efficiency

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The Drycon dry bottom ash extraction system is designed to remove bottom ash beneath the furnace, cooling it without any need of water. Fresh air in countercurrent flow to the ash is used for the ash cooling. Data presented show how savings of time and costs can be achieved with this system and how a boiler efficiency can be increased using this technology. Considerable advantages in the reliability of operation with new improvements of the design are described. 7 figs.

  5. Characterization of ash pond ashes from 3rd thermal power plant by SEM/EDX and XRD methods

    OpenAIRE

    A Minjigmaa; Ts Zolzaya; E Bayanjargal; B Davaabal; J Temuujin

    2014-01-01

      Coal combustion by products from ash pond of 3rdthermal power plant of Ulaanbaatar city have been collected in 2010 and 2013 years. The ash samples have been characterized by XRD, XRF and SEM-EDX methods in order to evaluate their chemical and mineralogical composition changes with disposed times. The mineralogical composition of ash varies with time though the chemical composition of the ashes were close each other. Possibly, inefficient operating condition of the TPS shows influence on th...

  6. JV Task 106 - Feasibility of CO2 Capture Technologies for Existing North Dakota Lignite-Fired Pulverized Coal Boilers

    Energy Technology Data Exchange (ETDEWEB)

    Michael L. Jones; Brandon M. Pavlish; Melanie D. Jensen

    2007-05-01

    The goal of this project is to provide a technical review and evaluation of various carbon dioxide (CO{sub 2}) capture technologies, with a focus on the applicability to lignite-fired facilities within North Dakota. The motivation for the project came from the Lignite Energy Council's (LEC's) need to identify the feasibility of CO{sub 2} capture technologies for existing North Dakota lignite-fired, pulverized coal (pc) power plants. A literature review was completed to determine the commercially available technologies as well as to identify emerging CO{sub 2} capture technologies that are currently in the research or demonstration phase. The literature review revealed few commercially available technologies for a coal-fired power plant. CO{sub 2} separation and capture using amine scrubbing have been performed for several years in industry and could be applied to an existing pc-fired power plant. Other promising technologies do exist, but many are still in the research and demonstration phases. Oxyfuel combustion, a technology that has been used in industry for several years to increase boiler efficiency, is in the process of being tailored for CO{sub 2} separation and capture. These two technologies were chosen for evaluation for CO{sub 2} separation and capture from coal-fired power plants. Although oxyfuel combustion is still in the pilot-scale demonstration phase, it was chosen to be evaluated at LEC's request because it is one of the most promising emerging technologies. As part of the evaluation of the two chosen technologies, a conceptual design, a mass and energy balance, and an economic evaluation were completed.

  7. Project ash cultch: A report on optimal oyster cultch based on a prepared fly ash substratum

    International Nuclear Information System (INIS)

    Price, K.S.; Hansen, K.M.; Schlekat, C.E.

    1991-01-01

    Based on a three year study involving setting, growth, mortality, oyster condition, and metals accumulation, the evidence is extensive and convincing that stabilized coal ash is an acceptable oyster growing cultch (substratum). Oyster larvae are attracted to set on coal ash cultch at commercial fishery densities, tend to grow as well as on natural substrata (oyster shell), and are moderately more exposed to predators on the puck shaped ash materials as produced for this study. Oysters grown for one to two years on coal ash do not accumulate heavy metals and generally are in good health as measured by several biological condition indexes

  8. Effects of Wood Ash on Soil Fungi

    DEFF Research Database (Denmark)

    Cruz Paredes, Carla

    ), copper (Cu) and nickel (Ni), is a major environmental concern. This work is part of the project ASHBACK (www.ashback.dk) which addresses the potentials and possible problems in re-distributing wood ash to the forest. The aim of this thesis was to determine the effects of biomass ash application...... in a Norway spruce forest where different amounts of wood ash were spread on the soil to study the effects on ectomycorrhizal (ECM) fungi, bioaccumulation of metals in sporocarps, and microbial communities. Laboratory microcosm experiments were run in parallel to the field studies, to compare the effects...... of wood ash with factorial additions of lime and Cd to disentangle the pH and Cd effects of wood ash amendments using community trait distributions. Barley yield, P content, and Cd content were not affected by biomass ashes. Some arbuscular mycorrhizal (AM) fungal species were reduced when biomass ashes...

  9. Life cycle adaption of biofuel ashes. Evaluation of new techniques for pelletizing of biofuel ashes, especially regarding operational properties and environmental effects in the forest after ash recycling. Stage 1

    International Nuclear Information System (INIS)

    Loevgren, Linnea; Lundmark, Jan-Erik; Jansson, Charlotta

    2000-11-01

    The aim of the project 'Adaptation of Wood Ashes to Recycling' is to evaluate a new technique - roll pelleting - for making wood ash suitable for reuse as a fertiliser for woodland. The project is being carried out at the forest product companies AssiDomaen and Stora Enso. The main financier is the Swedish National Energy Administration. Other financiers are AssiDomaen, Stora Enso, The Thermal Engineering Research Institute and The Forestry Research Institute of Sweden. The project has involved the construction of a full-scale roll pelleter in a mobile container and its trial operation at two Swedish pulp and paper mills. The leaching properties of the ash products were studied with a laboratory method. In addition, the effects of ash fertilisation with these products are being studied in a four-year field trial. Effects on soil pH, nutrient supply, soil water chemistry and ground vegetation are being evaluated by The Forestry Research Institute of Sweden and will be reported separately in the year 2003. In a laboratory prestudy, the leaching properties of pellets from twelve different ash products made in a laboratory prototype machine were evaluated. The ash products were made from residues from the AssiDomaen Froevi mill and the Stora Enso Fors mill. Fly ash from Froevi was used alone and mixed with green liquor sludge and lime sludge respectively. Fly ash from Fors was also used alone and mixed with coating colour. The laboratory method used for the evaluation of leaching properties is the method developed by IVL The Swedish Environmental Research Institute Ltd. The results show that the progress of the leaching of roll pelleted ash is significantly slower than for the corresponding crushed product and a reference lime product. The speed of leaching, measured as acid neutralisation capacity, ANC, was significantly lower for the roll pelleted ash compared to self-hardened and crushed ash products. Because of the high content of calcium, lime has on the whole, a

  10. Adsorption study of mercury on lignite in the presence of different anions

    Directory of Open Access Journals (Sweden)

    Irma Robles

    2016-05-01

    Full Text Available This study compares the effect of different anions such as chloride, nitrate, and sulphate on the mercury adsorption onto lignite, which was a model material for the humus-containing organics in soil, and can be considered as a natural sorbent in the remediation of contaminated sites. Since the complex formation can significantly influence the mercury sorption, besides chloride, the effects of other complex-forming agents such as ethylenediaminetetraacetic acid, and thiocyanate were also tested. Various batch type and dynamic experiments were performed and four sorption models (Langmuir, Freundlich, Temkin and Dubinin-Radushkevich were used to evaluate the sorption data.

  11. Ash fusion temperatures and their association with the transformations of coal ash particles to slag

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.K.; Wall, T.F.; Gupta, R.P. [Cooperative Research Centre for Black Coal Utilisation, Newcastle, NSW (Australia); Creelman, R.A. [Creelman (R.A.) and Associates, Sydney, NSW (Australia)

    1997-04-01

    Ash deposition on furnace walls in PF (pulverized fuel) furnaces is called slagging when it occurs in the high temperature areas of furnaces directly exposed to flame radiation and fouling in other regions such as tubes in the convection section of the boiler. There are well documented shortcomings of certain approaches relating to their uncertainties as predictive tools for plant performance such as poor repeatability and re-producibility of ash fusion measurements. The nature of physical and chemical changes occurring during melting of coal ash has been investigated in the current study to provide an alternative procedure to the ash fusion test. Shrinkage measurements are frequently used in metallurgy and ceramic science to study the physical properties of materials at high temperatures. The output of this experiment provides three to four `peaks` (maximum rate of shrinkage with temperature) of different intensity and at different temperatures which are related to melting characteristics of the sample. It was concluded that shrinkage extents exceeding 50 percent indicated that the effect of the ash particle size is of secondary importance compared to ash chemistry in determining shrinkage levels, with fine particles giving rapid shrinkage events 10 degrees C lower in temperature. (author). 7 figs., refs.

  12. Publication sites productive uses of combustion ash

    Science.gov (United States)

    Publication Sites Productive Uses of Combustion Ash For more information contact: e:mail: Public waste combustion ash in landfills. The new technology brief describes recent studies where ash was used

  13. Effects of chemical composition of fly ash on efficiency of metal separation in ash-melting of municipal solid waste

    Energy Technology Data Exchange (ETDEWEB)

    Okada, Takashi, E-mail: t-okada@u-fukui.ac.jp [Laboratory of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Tomikawa, Hiroki [Laboratory of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan)

    2013-03-15

    Highlights: ► Separation of Pb and Zn from Fe and Cu in ash-melting of municipal solid waste. ► Molar ratio of Cl to Na and K in fly ash affected the metal-separation efficiency. ► The low molar ratio and a non-oxidative atmosphere were better for the separation. - Abstract: In the process of metal separation by ash-melting, Fe and Cu in the incineration residue remain in the melting furnace as molten metal, whereas Pb and Zn in the residue are volatilized. This study investigated the effects of the chemical composition of incineration fly ash on the metal-separation efficiency of the ash-melting process. Incineration fly ash with different chemical compositions was melted with bottom ash in a lab-scale reactor, and the efficiency with which Pb and Zn were volatilized preventing the volatilization of Fe and Cu was evaluated. In addition, the behavior of these metals was simulated by thermodynamic equilibrium calculations. Depending on the exhaust gas treatment system used in the incinerator, the relationships among Na, K, and Cl concentrations in the incineration fly ash differed, which affected the efficiency of the metal separation. The amounts of Fe and Cu volatilized decreased by the decrease in the molar ratio of Cl to Na and K in the ash, promoting metal separation. The thermodynamic simulation predicted that the chlorination volatilization of Fe and Cu was prevented by the decrease in the molar ratio, as mentioned before. By melting incineration fly ash with the low molar ratio in a non-oxidative atmosphere, most of the Pb and Zn in the ash were volatilized leaving behind Fe and Cu.

  14. The effect of environmental pollution on the respiratory system of lignite miners: a diachronic study.

    Science.gov (United States)

    Sichletidis, L; Tsiotsios, I; Chloros, D; Daskalopoulou, E; Ziomas, I; Michailidis, K; Kottakis, I; Konstantinidis, T H; Palladas, P

    2004-01-01

    It is not known whether working in surface lignite mines can cause x-ray lesions or disorders of respiratory function. The aim of the study was to investigate the diachronic impact of environmental pollution on the respiratory system of lignite miners at mines in Eordea, Greece. Cases of 199 workers (Group A) residing permanently in the Eordea valley and 151 (Group B) living outside the Eordea valley were studied during Phase I and then re-examined after three years (Phase II). These cases were compared to those of 71 office workers living in Eordea valley (Group C) and to 96 living in Grevena, a region without pollution (Group D). The study included the completion of the MRC questionnaire for the detection of respiratory diseases, pulmonary function tests, measurement of diffusion capacity, otorhinolaryngologic examination, rhinomanonetry as well as chest and paranasal cavity X-rays. Chronic bronchitis was reported by 26.8%, 24.8%, 17.9% and 10.6% respectively of the subjects of groups A, B, C and D according to the answers of the questionnaire (pmines under conditions of excessive pollution by airborne contaminants have a high prevalence of atrophic rhinitis and, in addition to other standard examinations, should undergo rhinomanometry testing and X-ray imaging of the paranasal cavities.

  15. Gas generation in incinerator ash; Gasbildning i aska

    Energy Technology Data Exchange (ETDEWEB)

    Arm, Maria; Lindeberg, Johanna; Rodin, Aasa; Oehrstroem, Anna; Backman, Rainer; Oehman, Marcus; Bostroem, Dan

    2006-02-15

    In recent years, explosions have occurred in certain phases of ash handling in Sweden. Investigations have revealed that hydrogen may have been present in all cases. The hydrogen is believed to be generated by chemical reactions of aluminium and other metals within the ash in the presence of water. The purpose with this study is to increase the knowledge of gas generation of incinerator ash. Thereby, guides for appropriate ash management can be introduced and the risk for further explosions prevented. The study has comprised analyses of the ash properties, such as chemical and physical composition and the pH, of ash from 14 incineration plants (mostly waste incineration plants). Different fractions of ash materials representing different parts of the process in each plant have been analysed. Furthermore, the fuel and the technical differences between the plants have been analysed. A tool for measuring the gas generation in the laboratory has been developed and the gas generation of the different ash materials at natural and increased pH was measured. Gas analyses and thermodynamic calculations have also been performed. The results showed that: bottom ash from fluidised bed boilers generated small amounts of gas at increased pH, much smaller amounts than the idle pass, cyclone and filter ash did, bottom ash from grate fired boilers generated more gas at increased pH than their cyclone ash and filter ash, with exception of the Linkoeping plant, all bio waste incineration plants generated ash with low gas generation potential, all fly ash materials with a gas generation potential of more than 10 l/kg originated from municipal waste incineration plants, filter ash that had been stored in oxygen rich environment generated significant less gas than fresh filter ash of the same origin, hardly any other gases were generated apart from hydrogen (very small amounts of acetone, furane, benzene and most likely methane were detected in some of the ash materials), there were no

  16. Utilization of Hospital Waste Ash in Concrete

    Directory of Open Access Journals (Sweden)

    Shazim Ali Memon

    2013-01-01

    Full Text Available Hospital waste management is a huge problem in Pakistan. The annual production of medical waste produced from health care facilities, in Pakistan, is around 250,000 tons. This research paper is intended to evaluate the feasibility of using of hospital waste ash obtained from Pakistan Institute of Medical Sciences, Rawalpindi, Pakistan, as partial replacement of cement. The main variable in this research is the amount of hospital waste ash (2, 4, 6 and 8% by weight of cement while the amount of cementitious material, water to cementitious material ratio, fine and coarse aggregate content were kept constant. Test results substantiate that hospital waste ash can be used in concrete. XRD (X-Ray Diffraction of hospital waste ash showed that it is rich in calcite while scanning electron micrographs indicated that the particles of hospital waste ash have highly irregular shape. The slump value, density of fresh concrete and water absorption decreased with the increase in the quantity of hospital waste ash in the mix. At 3 days of testing, the compressive strength of mixes with hospital waste ash was higher than the control mix while at 7 and 28 days the CM (Control Mix showed higher strength than the hospital waste ash mixes except the mix containing 2% hospital waste ash by weight of cement.

  17. Utilization of hospital waste ash in concrete

    International Nuclear Information System (INIS)

    Memon, S.; Sheikh, M.

    2013-01-01

    Hospital waste management is a huge problem in Pakistan. The annual production of medical waste produced from health care facilities, in Pakistan, is around 250,000 tons. This research paper is intended to evaluate the feasibility of using of hospital waste ash obtained from Pakistan Institute of Medical Sciences, Rawalpindi, Pakistan, as partial replacement of cement. The main variable in this research is the amount of hospital waste ash (2, 4, 6 and 8% by weight of cement) while the amount of cementitious material, water to cementitious material ratio, fine and coarse aggregate content were kept constant. Test results substantiate that hospital waste ash can be used in concrete. XRD (X-Ray Diffraction) of hospital waste ash showed that it is rich in calcite while scanning electron micrographs indicated that the particles of hospital waste ash have highly irregular shape. The slump value, density of fresh concrete and water absorption decreased with the increase in the quantity of hospital waste ash in the mix. At 3 days of testing, the compressive strength of mixes with hospital waste ash was higher than the control mix while at 7 and 28 days the CM (Control Mix) showed higher strength than the hospital waste ash mixes except the mix containing 2% hospital waste ash by weight of cement. (author)

  18. The UZPI ash content monitoring device

    Energy Technology Data Exchange (ETDEWEB)

    Novikov, E.P.; Bezverkhii, E.A.; Mozhaev, L.G.

    1987-07-01

    This paper describes the results of industrial trials (in coal preparation plants) to establish the accuracy of the UZPI device which determines coal ash content using X-ray detection. It is designed to monitor ash content in the 4-40% range in coal with a grain size of 0-100 mm and a coal layer thickness of 50-150 mm (depending on the ash content and grain size). The ash frequently contains oxides, and although variations in magnesium, aluminium, silicon and sulfur oxides have virtually no effect on accuracy of the UZPI, changes in the levels of calcium oxides and particularly iron oxides have a considerable influence on measurement accuracy (caused by changes in their gamma ray scattering cross section values and atomic numbers). The overall sensitivity to ash content in coal varies from 1.6 to 2.4% abs./% while that to iron oxides in ash is 0.4% abs./%. Concludes that this device is suitable for use in coal preparation plants on thin layers of coal, but its efficiency is affected by external influences, e.g. fluctuations in conveyor loading.

  19. Advanced power assessment for Czech lignite task 3.6. Topical report

    Energy Technology Data Exchange (ETDEWEB)

    Sondreal, E.A.; Mann, M.D.; Weber, G.W.; Young, B.C.

    1995-12-01

    Major reforms in the Czech energy sector have been initiated to reverse 40 years of central planning, subsidized energy pricing, unchecked pollution from coal-fired plants, concerns over nuclear safety and fuel cycle management, and dependence on the former U.S.S.R. for oil, gas, and nuclear fuel processing. Prices for electricity, heat, and natural gas paid by industry are close to western levels, but subsidized prices for households are as much as 40% lower and below economic cost. State control of major energy enterprises is being reduced by moving toward government-regulated, investor-owned companies to raise needed capital, but with a strategic stake retained by the state. Foreign firms will participate in privatization, but they are not expected to acquire a controlling interest in Czech energy companies. Economic conditions in the Czech Republic are now improving after the disruptions caused by restructuring since 1989 and separation of the former Czech and Slovak Federal Republics in January 1993. The downturn in the economy after 1989 was concentrated in energy-intensive heavy industry, and recovery is paced by consumer trade, services, light industry and construction. Energy use in relation to gross domestic product (GDP) has declined, but it is still significantly higher than in OECD (Organization for Economic Cooperation and Development) countries. The GDP increased by 2% in 1994 after dropping 22% between 1989 and 1993. A positive balance of payments has been achieved, with foreign investment offsetting a small trade deficit. The government`s external debt is only 4% of GDP. This report studies the application of lignite resources within the newly formulated energy policies of the republic, in light of a move toward privatization and stronger air pollution regulations. Lignite has represented the major energy source for the country.

  20. Quality characteristics of Greek fly ashes and potential uses

    Energy Technology Data Exchange (ETDEWEB)

    Skodras, G.; Grammelis, P.; Kakaras, E. [Institute for Solid Fuels Technology and Applications, Ptolemais (Greece); Karangelos, D.; Anagnostakis, M.; Hinis, E. [Nuclear Engineering Section, Mechanical Engineering Department, National Technical University of Athens, Athens (Greece)

    2007-01-15

    The main characteristics of fly ash from Greek coal-fired boilers are presented in this paper in relation to its exploitation potential. Both fuel and fly ash samples were collected and analyzed according to the ASTM Standards. Apart from the typical analyses (proximate, ultimate, ash analysis and calorific value), an ICP-AES spectrometer was used for the analysis of heavy metals in the ash. Experimental measurements in order to determine the radioactivity content of raw fuel and the fly ash were carried out as well. A representative fly ash sample from Ptolemais power plant was evaluated and tested as filler in Self-Compacting Concrete (SCC). Ashes from the Greek brown coal are classified in type C, most of the fly ash being produced in Ptolemais of Northern Greece, while the rest in Megalopolis. Ptolemais fly ash is rich in calcium compounds, while Megalopolis fly ash contains more pyrite. Increased heavy metal concentrations are observed in the fly ash samples of Greek coal. Greek fly ash appears to have not only pozzolanic but also hydraulic behaviour. Furthermore, Greek fly ash, depending on its origin, may have relatively high natural radioactivity content, reaching in the case of Megalopolis fly ash 1 kBq kg{sup -1} of {sup 226}Ra. The laboratory results showed that fly ashes can be a competitive substitute to conventional limestone filler material in SCC. Fly ash is mostly used in Greece in cement industry replacing cement clinker and aiming to the production of special types of Portland cements. However, a more aggressive utilisation strategy should be developed, since low quantities of the total produced fly ash are currently further utilised. (author)

  1. Breeding strategies for the development of emerald ash borer - resistant North American ash

    Science.gov (United States)

    Jennifer L. Koch; David W. Carey; Kathleen S. Knight; Therese Poland; Daniel A. Herms; Mary E. Mason

    2012-01-01

    The emerald ash borer (Agrilus plannipennis; EAB) is a phloem-feeding beetle that is endemic to Asia. It was discovered in North America in 2002, found almost simultaneously near Detroit, Michigan and Windsor, Ontario, Canada. Adult beetles feed on ash (Fraxinus spp.) foliage, but larval feeding on phloem, cambium, and...

  2. Outlook for ash in your forest: results of emerald ash borer research and implications for management

    Science.gov (United States)

    Kathleen S. Knight

    2014-01-01

    Since its accidental introduction near Detroit, Michigan, in the mid-1990s, emerald ash borer (EAB) has rapidly spread through much of the U.S. and adjacent Canada, leaving millions of dead ash trees in Midwestern states (4,11). Unfortunately, EAB attacks trees as small as an inch in stem diameter and it attacks all five ash species native to the region - white, green...

  3. Analysis list: ash-2 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ash-2 Adult,Embryo + ce10 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/target/as...h-2.1.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/target/ash-2.5.tsv http://dbarchive.biosciencedbc....jp/kyushu-u/ce10/target/ash-2.10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/colo/ash-2.Adult.tsv,http://dbarchive.bioscience...dbc.jp/kyushu-u/ce10/colo/ash-2.Embryo.tsv http://dbarchive.bioscience...dbc.jp/kyushu-u/ce10/colo/Adult.gml,http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/colo/Embryo.gml ...

  4. Composites Based on Fly Ash and Clay

    International Nuclear Information System (INIS)

    Fidancevska, E.; Jovanov, V.; Angusheva, B.; Srebrenkoska, V.

    2014-01-01

    Fly ash is a waste generated from the coal combustion during the production of electricity in the thermal power plants. It presents industrial by-product containing Technologically Enhanced Natural Occurring Radioactive Materials (TENORM) with the great potential for valorisation. Fly ash is successfully utilized in cement and concrete industry, also in ceramics industry as component for manufacturing bricks and tiles, and recently there are many investigations for production of glass-ceramics from fly ash. Although the utilization of fly ash in construction and civil engineering is dominant, the development of new alternative application for its further exploitation into new products is needed. This work presents the possibility for fly ash utilization for fabricating dense composites based on clay and fly ash with the potential to be used in construction industry

  5. Physiological responses of emerald ash borer larvae to feeding on different ash species reveal putative resistance mechanisms and insect counter-adaptations.

    Science.gov (United States)

    Rigsby, C M; Showalter, D N; Herms, D A; Koch, J L; Bonello, P; Cipollini, D

    2015-07-01

    Emerald ash borer, Agrilus planipennis Fairmaire, an Asian wood-boring beetle, has devastated ash (Fraxinus spp.) trees in North American forests and landscapes since its discovery there in 2002. In this study, we collected living larvae from EAB-resistant Manchurian ash (Fraxinus mandschurica), and susceptible white (Fraxinus americana) and green (Fraxinus pennsylvanica) ash hosts, and quantified the activity and production of selected detoxification, digestive, and antioxidant enzymes. We hypothesized that differences in larval physiology could be used to infer resistance mechanisms of ash. We found no differences in cytochrome P450, glutathione-S-transferase, carboxylesterase, sulfotransferase, and tryptic BApNAase activities between larvae feeding on different hosts. Despite this, Manchurian ash-fed larvae produced a single isozyme of low electrophoretic mobility that was not produced in white or green ash-fed larvae. Additionally, larvae feeding on white and green ash produced two serine protease isozymes of high electrophoretic mobility that were not observed in Manchurian ash-fed larvae. We also found lower activity of β-glucosidase and higher activities of monoamine oxidase, ortho-quinone reductase, catalase, superoxide dismutase, and glutathione reductase in Manchurian ash-fed larvae compared to larvae that had fed on susceptible ash. A single isozyme was detected for both catalase and superoxide dismutase in all larval groups. The activities of the quinone-protective and antioxidant enzymes are consistent with the resistance phenotype of the host species, with the highest activities measured in larvae feeding on resistant Manchurian ash. We conclude that larvae feeding on Manchurian ash could be under quinone and oxidative stress, suggesting these may be potential mechanisms of resistance of Manchurian ash to EAB larvae, and that quinone-protective and antioxidant enzymes are important counter-adaptations of larvae for dealing with these resistance

  6. Ash Stabilization Campaign Blend Plan

    International Nuclear Information System (INIS)

    Winstead, M.L.

    1995-01-01

    This Stabilization Blend Plan documents the material to be processed and the processing order for the FY95 Ash Stabilization Campaign. The primary mission of this process is to reduce the inventory of unstable plutonium bearing ash. The source of the ash is from Rocky Flats and the 232-Z incinerator at the Plutonium Finishing Plant (PFP). The ash is currently being stored in Room 235B and Vault 174 in building 234-5Z. The sludge is to be thermally stabilized in a glovebox in room 230A of the 234-5Z building and material handling for the process will be done in room 230B of the same building. The campaign is scheduled for approximately 12--16 weeks. A total of roughly 4 kg of Pu will be processed

  7. Adhesion Strength of Biomass Ash Deposits

    DEFF Research Database (Denmark)

    Laxminarayan, Yashasvi; Jensen, Peter Arendt; Wu, Hao

    2016-01-01

    . Therefore, timely removal of ash deposits is essential for optimal boiler operation. In order to improve the qualitative and quantitative understanding of deposit shedding in boilers, this study investigates the shear adhesion strength of biomass ash deposits on superheater tubes. Artificial biomass ash...... deposits were prepared on superheater tubes and sintered in an oven at temperatures up to 1000 °C. Subsequently, the deposits were sheared off by an electrically controlled arm, and the corresponding adhesion strength was measured. The results reveal the effect of temperature, ash/deposit composition......, sintering duration, and steel type on the adhesion strength....

  8. Failure to phytosanitize ash firewood infested with emerald ash borer in a small dry kiln using ISPM-15 standards.

    Science.gov (United States)

    Goebel, P Charles; Bumgardner, Matthew S; Herms, Daniel A; Sabula, Andrew

    2010-06-01

    Although current USDA-APHIS standards suggest that a core temperature of 71.1 degrees C (160 degrees F) for 75 min is needed to adequately sanitize emerald ash borer, Agrilus planipennis Fairmaire-infested firewood, it is unclear whether more moderate (and economical) treatment regimes will adequately eradicate emerald ash borer larvae and prepupae from ash firewood. We constructed a small dry kiln in an effort to emulate the type of technology a small- to medium-sized firewood producer might use to examine whether treatments with lower temperature and time regimes successfully eliminate emerald ash borer from both spilt and roundwood firewood. Using white ash (Fraxinus americana L.) firewood collected from a stand with a heavy infestation of emerald ash borer in Delaware, OH, we treated the firewood using the following temperature and time regime: 46 degrees C (114.8 degrees F) for 30 min, 46 degrees C (114.8 degrees F) for 60 min, 56 degrees C (132.8 degrees F) for 30 min, and 56 degrees C (132.8 degrees F) for 60 min. Temperatures were recorded for the outer 2.54-cm (1-in.) of firewood. After treatment, all firewood was placed under mesh netting and emerald ash borer were allowed to develop and emerge under natural conditions. No treatments seemed to be successful at eliminating emerald ash borer larvae and perpupae as all treatments (including two nontreated controls) experienced some emerald ash borer emergence. However, the 56 degrees C (132.8 degrees F) treatments did result in considerably less emerald ash borer emergence than the 46 degrees C (114.8 degrees F) treatments. Further investigation is needed to determine whether longer exposure to the higher temperature (56 degrees C) will successfully sanitize emerald ash borer-infested firewood.

  9. Concentration of heavy metals and trace elements in soils, waters and vegetables and assessment of health risk in the vicinity of a lignite-fired power plant

    Energy Technology Data Exchange (ETDEWEB)

    Noli, Fotini, E-mail: noli@chem.auth.gr; Tsamos, Panagiotis, E-mail: pktsamos@chem.auth.gr

    2016-09-01

    The pollution of agricultural soils, waters and products in the regions of lignite mines and fired power plants is of great importance. The concentration of As, Βa, Co, Cr, Sr, Sc, Th, U, Zn in soils and waters in the vicinity of a lignite-fired power plant in Northern Greece was determined using Instrumental Neutron Activation Analysis. The determination frequency was every three months during a period of one year in order to evaluate the seasonal impact of the pollution to the environment. Measurements were performed in three locations around the lignite mine as well as in one reference location at a certain distance from the mine. The results, which exhibited a slight seasonal variation, were compared, where possible, with literature values from other countries. The obtained data in most of the cases did not exceed the normal levels and indicated that the investigated area was only slightly contaminated. The concentration of heavy and trace metals was also measured in three common garden crops (tomato, cucumber and parsley) grown in this area. The calculated transfer factors (TF) from soil to vegetables and health risk quotients (HQ) do not denote a health risk. - Highlights: • Seasonal variation of heavy metals concentrations in soils and waters in a lignite mining area. • The elevated concentrations detected by NAA indicating minor contamination of the studied area. • Determination of minor and trace elements in vegetables. • The transfer factors and health risk quotients indicating a possible slight contamination in the area.

  10. Concentration of heavy metals and trace elements in soils, waters and vegetables and assessment of health risk in the vicinity of a lignite-fired power plant

    International Nuclear Information System (INIS)

    Noli, Fotini; Tsamos, Panagiotis

    2016-01-01

    The pollution of agricultural soils, waters and products in the regions of lignite mines and fired power plants is of great importance. The concentration of As, Βa, Co, Cr, Sr, Sc, Th, U, Zn in soils and waters in the vicinity of a lignite-fired power plant in Northern Greece was determined using Instrumental Neutron Activation Analysis. The determination frequency was every three months during a period of one year in order to evaluate the seasonal impact of the pollution to the environment. Measurements were performed in three locations around the lignite mine as well as in one reference location at a certain distance from the mine. The results, which exhibited a slight seasonal variation, were compared, where possible, with literature values from other countries. The obtained data in most of the cases did not exceed the normal levels and indicated that the investigated area was only slightly contaminated. The concentration of heavy and trace metals was also measured in three common garden crops (tomato, cucumber and parsley) grown in this area. The calculated transfer factors (TF) from soil to vegetables and health risk quotients (HQ) do not denote a health risk. - Highlights: • Seasonal variation of heavy metals concentrations in soils and waters in a lignite mining area. • The elevated concentrations detected by NAA indicating minor contamination of the studied area. • Determination of minor and trace elements in vegetables. • The transfer factors and health risk quotients indicating a possible slight contamination in the area.

  11. Methods to Improve Survival and Growth of Planted Alternative Species Seedlings in Black Ash Ecosystems Threatened by Emerald Ash Borer

    Science.gov (United States)

    Nicholas Bolton; Joseph Shannon; Joshua Davis; Matthew Grinsven; Nam Noh; Shon Schooler; Randall Kolka; Thomas Pypker; Joseph Wagenbrenner

    2018-01-01

    Emerald ash borer (EAB) continues to spread across North America, infesting native ash trees and changing the forested landscape. Black ash wetland forests are severely affected by EAB. As black ash wetland forests provide integral ecosystem services, alternative approaches to maintain forest cover on the landscape are needed. We implemented simulated EAB infestations...

  12. Fluidized bed combustion with the use of Greek solid fuels

    Directory of Open Access Journals (Sweden)

    Kakaras Emmanuel

    2003-01-01

    Full Text Available The paper is an overview of the results obtained up to date from the combustion and co-combustion activities with Greek brown coal in different installations, both in semi-industrial and laboratory scale. Combustion tests with Greek lignite were realized in three different Circulating Fluidized Bed Combustion (CFBC facilities. Low rank lignite was burned in a pilot scale facility of approx. 100kW thermal capacity, located in Athens (NTUA and a semi-industrial scale of 1.2 MW thermal capacity, located at RWE's power station Niederaussem in Germany. Co-combustion tests with Greek xylitic lignite and waste wood were carried out in the 1 MWth CFBC installation of AE&E, in Austria. Lab-scale co-combustion tests of Greek pre-dried lignite with biomass were accomplished in a bubbling fluidized bed in order to investigate ash melting problems. The obtained results of all aforementioned activities showed that fluidized bed is the appropriate combustion technology to efficiently exploit the low quality Greek brown coal either alone or in conjunction with biomass species.

  13. Wildland fire ash: future research directions

    Science.gov (United States)

    Bodí, Merche B.; Martins, Deborah A.; Cerdà, Artemi; Balfour, Victoria N.; Santin, Cristina; Doerr, Stefan H.; Pereira, Paulo; Mataix-Solera, Jorge

    2014-05-01

    Ash is a key component of the forest fires affected land (Cerdà, 1998; Bodí et al., 2011; Pereira et al., 2013a). Ash controls the hydrological processes and determines the water repellency (Dlapa et al., 2012) and the infiltration rates (Cerdà and Doerr, 2008;). Moreover, ash is the key factor on runoff initiation and then on the soil erosion. Little is known about the impact of ash in different ecosystems, but during the last decade a substantial increase in the papers that show the role of ash in the Earth and Soil System were published (Bodí et al., 2012; Pereira et al., 2013b).. Ash is being found as the key component of the post-fire pedological, geomorphological and hydrological response after forest fires (Fernández et al., 2012; Martín et al., 2012; Bodí et al., 2013; Guénon et al., 2013; Pereira et al., 2013c). A recent State-of-the-Art review about wildland fire ash (Bodí et al., 2014) compiles the knowledge regarding the production, composition and eco-hydro-geomorphic effects of wildland fire ash. In the present paper we indicate the knowledge gaps detected and suggest topics that need more research effort concerning: i) data collection and analysis techniques: a) To develop standardized sampling techniques that allow cross comparison among sites and avoid inclusion of the underlying soil unless the burned surface soil forms part of the ash layer, b) To develop standardized methods to define and characterize ash, including its color, physical properties such as particle size distribution or density, proportion of pyrogenic C, chemical and biological reactivity and persistence in the environment, c) To validate, calibrate and test measurements collected through remote sensing with on-the-ground measurements. ii) ash production, deposition redistribution and fate: d) To untangle the significance of the effects of maximum temperature reached during combustion versus the duration of heating, e) To understand the production of ash by measuring its

  14. Characterization of ashes from biofuels

    Energy Technology Data Exchange (ETDEWEB)

    Frandsen, F.J.; Hansen, L.A. [Technical Univ. of Denmark. Dept. of Chemical Engineering (Denmark); Soerensen, H.S. [Geological Survey of Denmark and Greenland (Denmark); Hjuler, K. [dk-TEKNIK. Energy and Environment (Denmark)

    1998-02-01

    One motivation for initiating the present project was that the international standard method of estimating the deposit propensity of solid fuels, of which a number of variants exist (e.g. ISO, ASTM, SD, DIN), has shown to be unsuitable for biomass ashes. This goal was addressed by the development of two new methods for the detection of ash fusibility behaviour based on Simultaneous Thermal Analysis (STA) and High Temperature Light Microscopy (HTLM), respectively. The methods were developed specifically for ashes from biofuels, but are suitable for coal ashes as well. They have been tested using simple salt mixtures, geological standards and samples from straw CHP and coal-straw PF combustion plants. All samples were run in a nitrogen atmosphere at a heating rate of 10 deg. C/min. In comparison with the standard method, the new methods are objective and have superior repeatability and sensitivity. Furthermore, the two methods enable the melting behavior to be characterized by a continuous measurement of melt fraction versus temperature. Due to this two-dimensional resolution of the results, the STA and HTLM methods provide more information than the standard method. The study of bottom ash and fly ash as well as deposit samples from straw test firings at the Haslev and Slagelse Combined Heat and Power plants resulted in a better understanding of mineral behaviour during straw grate firing. In these tests a number of straws were fired which had been carefully selected for having different qualities with respect to sort and potassium and chlorine contents. By studying bottom ashes from Slagelse it was found that the melting behaviour correlated with the deposition rate on a probe situated at the outlet part of the combustion zone. (EG)

  15. Crowdsourcing genomic analyses of ash and ash dieback – power to the people

    Directory of Open Access Journals (Sweden)

    MacLean Dan

    2013-02-01

    Full Text Available Abstract Ash dieback is a devastating fungal disease of ash trees that has swept across Europe and recently reached the UK. This emergent pathogen has received little study in the past and its effect threatens to overwhelm the ash population. In response to this we have produced some initial genomics datasets and taken the unusual step of releasing them to the scientific community for analysis without first performing our own. In this manner we hope to ‘crowdsource’ analyses and bring the expertise of the community to bear on this problem as quickly as possible. Our data has been released through our website at oadb.tsl.ac.uk and a public GitHub repository.

  16. Optimization of a lignite-fired open pulverizing system boiler process based on variations in the drying agent composition

    International Nuclear Information System (INIS)

    Ma, Youfu; Zhang, Hua; Yuan, Yichao; Wang, Zhiyun

    2015-01-01

    This paper evaluates three lignite-fired OPSB (open pulverizing system boiler) processes, named OPSB-A, OPSB-B and OPSB-C, corresponding to three options of drying agents used for the pulverizing systems. OPSB-B is similar to our previous work [18] on drying agent composition. Performances of the three OPSBs were calculated and compared with a 600 MW lignite-fired boiler as the reference. The results showed that the coal savings of OPSB-A and OPSB-C were 5.41% and 4.06% in comparison with the reference boiler, whereas for OPSB-B, the savings was 2.57%. Accordingly, emissions of each OPSB could be reduced in proportion to the coal savings. Among the three OPSBs, OPSB-C showed the best performance of water recovery from mill-exhausts because it had the highest mill-exhaust water dew point of 73.2 °C, whereas the exhaust dew points of OPSB-A and OPSB-B were 63.9 °C and 70.9 °C, respectively. Both OPSB-C and OPSB-B are beneficial for achieving a high mill-exhaust humidity ratio, which facilitates water recovery from the mill-exhaust, and a low oxygen content in mill-exhaust, which improves the operating safety of the pulverizing systems, whereas OPSB-A is relatively inferior in these respects. The OPSB-C process is recommended for engineering applications because of its favorable overall performances. - Highlights: • Three lignite-fired OPSB processes are analyzed based on a conventional 600 MW boiler. • OPSB-A, OPSB-B and OPSB-C show coal savings of 5.41%, 2.57 and 4.06%, respectively. • All OPSBs have a great advantage of water recovery from the flue gas, especially OPSB-C. • OPSB-C process is recommended in view of its favorable overall performances

  17. Leaching of saltstones containing fly ash

    International Nuclear Information System (INIS)

    Barnes, M.W.; Roy, D.M.; Langton, C.A.

    1985-01-01

    Two types of fly ash were incorporated in saltstones designed for potential encapsulation of Savannah River Plant low level defense waste. These fly ashes have some cementitious properties while at the same time their presence in substitution for cement slows early hydration. Class C fly ash has a high calcium content and is considered cementitious; Class F fly ash has a low calcium content and is not classified as cementitious. Leach tests were performed and physical properties were measured for saltstones containing each class, to see the differences in the effect of the fly ashes. The four waste ions nitrate, nitrite, sodium and sulfate were shown to leach by diffusion. Effective diffusivities were determined for these ions. Data for nitrate, the most important species from the environmental point of view, are shown in Table A. Saltstones made with Class C fly ash have substantially lower leach rates than those made with Class F fly ash. The leach rates, and therefore the square roots of the effective diffusivities, have been found to be proportional to the pore surface area per unit volume (or the ratio of pore volume to pore radius), to the fraction of waste containing solution, and to the inverse of the fraction of calcium in the saltstone. Rates and diffusivities are not proportional to the water to cement ratio, because this number depends on whether the fly ash is counted as cementitious, as in Class C cement, or not cementitious, as in Class F cement. In fact the relatively small amount of calcium in Class F cement contributes to the cementitious properties overall, though not so much as Class C cement. 4 refs., 2 figs., 6 tabs

  18. Characterisation of wood combustion ashes

    DEFF Research Database (Denmark)

    Maresca, Alberto

    The combustion of wood chips and wood pellets for the production of renewable energy in Denmark increased from 5.7 PJ to 16 PJ during the period 2000-2015, and further increases are expected to occur within the coming years. In 2012, about 22,300 tonnes of wood ashes were generated in Denmark....... Currently, these ashes are mainly landfilled, despite Danish legislation allowing their application onto forest and agricultural soils for fertilising and/or liming purposes. During this PhD work, 16 wood ash samples generated at ten different Danish combustion plants were collected and characterised...... for their composition and leaching properties. Despite the relatively large variations in the contents of nutrients and trace metals, the overall levels were comparable to typical ranges reported in the literature for other wood combustion ashes, as well as with regards to leaching. In general, the composition...

  19. Analysis list: Ash2l [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Ash2l Blood + mm9 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/target/Ash2l.1.tsv... http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/target/Ash2l.5.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/target/Ash2...l.10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/colo/Ash2l.Blood.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/colo/Blood.gml ...

  20. Properties of Fly Ash Blocks Made from Adobe Mould

    Science.gov (United States)

    Chokhani, Alankrit; Divakar, B. S.; Jawalgi, Archana S.; Renukadevi, M. V.; Jagadish, K. S.

    2018-06-01

    Fly ash being one of the industrial waste products poses a serious disposal problem. This paper presents an experimental study of utilization of fly ash to produce blocks with varying proportions and mix combinations. Composition of fly ash blocks mainly consist of fly ash and sand, with cementitious product as either cement, lime or both, such as fly ash-sand-cement, fly ash-sand-lime and fly ash-sand-cement-lime are used. Four different proportions for each of the mix combinations are experimented. Compressive strength, water absorption, Initial rate of absorption, and dry density of fly ash blocks are studied. The influence of partial and complete replacement of cement by lime is examined.