Directory of Open Access Journals (Sweden)
Renato Alexandre Costa de Santana
2007-04-01
Full Text Available A study on optimization of bath parameters for electrodeposition of Fe-W-B alloys from plating baths containing ammonia and citrate is reported. A 2³ full factorial design was successfully employed for experimental design analysis of the results. The corrosion resistance and amorphous character were evaluated. The bath conditions obtained for depositing the alloy with good corrosion resistance were: 0.01 M iron sulfate, 0.10 M sodium tungstate and 0.60 M ammonium citrate. The alloy was deposited at 12% current efficiency. The alloy obtained had Ecorr -0.841 V and Rp 1.463 x 10(4 Ohm cm². The deposit obtained under these conditions had an amorphous character and no microcracks were observed on its surface. Besides this, the bath conditions obtained for depositing the alloy with the highest deposition efficiency were: 0.09 M iron sulfate, 0.30 M sodium tungstate and 0.50 M ammonium citrate. The alloy was deposited at 50% current efficiency, with an average composition of 34 wt% W, 66 wt% Fe and traces of boron. The alloy obtained had Ecorr -0.800 V and Rp 1.895 x 10³ Ohm cm². Electrochemical corrosion tests verified that the Fe-W-B alloy deposited under both conditions had better corrosion resistance than Fe-Mo-B.
Energy Technology Data Exchange (ETDEWEB)
Liu, Yi; Yu, Tao [School of Physics and Nuclear Energy Engineering, Beihang University, Beijing 100191 (China); Zhu, Zhengyong; Zhong, Huicai [Institute of Microelectronics, Chinese Academy of Sciences, Beijing 100029 (China); Khamis, Khamis Masoud [School of Physics and Nuclear Energy Engineering, Beihang University, Beijing 100191 (China); Zhu, Kaigui, E-mail: kgzhu@buaa.edu.cn [School of Physics and Nuclear Energy Engineering, Beihang University, Beijing 100191 (China); Key Laboratory of Micro-Nano Measurement-Manipulation and Physics, Ministry of Education, Beihang University, Beijing 100191 (China)
2016-07-15
The perpendicular magnetic anisotropy (PMA) of a series of top MgO/CoFeB/W stacks were studied. In these stacks, the thickness of CoFeB is limited in a range of 1.1–2.2 nm. It was found that the stack can still maintain PMA in a 1.9 nm thick CoFeB free layer. Besides, we investigated the thermal stability factor ∆ of a spin transfer torque magnetic random access memory (STT-MRAM) by inserting an ultra-thin W film of 0.8 nm between two CoFeB films. The result shows a clear PMA behavior for the samples with CoFeB thickness up to 2.5 nm, and an in-plane magnetic anisotropy (IMA) when the CoFeB is thicker than 2.5 nm. Moreover, the thermal stability factor ∆ of the CoFeB stack with W insertion is about 132 for a 50 nm size STT-MRAM device, which is remarkably improved compared to 112 for a sample without W insertion. Our results represent an alternative way to realize the endurance at high annealing temperature, high-density and high ∆ in STT-MRAM device by ultra-thin W insertion. - Highlights: • The MgO/CoFeB/W multilayer can still maintain PMA in a CoFeB thickness of 1.9 nm. • The sample with 2.5 nm thickness of CoFeB by W insertion can still maintain PMA. • The sample with W insertion can still maintain PMA until the annealing temperature as high as 350 °C. • The thermal stability factor ∆ of sample with W insertion could be increase to about 132 for a 50 nm size STT-MRAM device.
W-band LiGA fabricated klystron
Song, Liqun
2002-01-01
Klystrino-W-band klystron was proposed by scientists at SLAC to satisfy recent applications in advanced accelerators, medical treatment, radars and communications. LiGA (a German acronym for lithographe, galvanoformung, and abformung) is introduced in the fabrication of klystrino for the first time in the history of microwave tube fabrication. The cold test experiments show that LiGA fabrication yields best surface smoothness compared with an alternative way EDM (Electrical Discharge Machining). Resultantly LiGA fabricated klystrino has the smallest wall loss which maximizes the circuit efficiency of the output structure. A multiple-gap coupled cavity is motivated to be employed as the klystrino output cavity for maximizing the efficiency. Klytrino is simulated by 1-D, 2-D and 3-D simulation codes. Particularly a complete klystrino is simulated intensively using 2-D MAGIC Particle-in-Cell (PIC) code either for beam absence or beam presence. Many simulation techniques are developed such as model transformation from 3-D to 2-D, circuit parameter simulation, dispersion characteristic analysis, pre bunched electron beam mode and so on. Klystrino, as a 3-D structure, is modeled by 3-D MAFIA for analyzing the cold circuit properties. 3-D MAGIC is explored to simulate klystrino for the actual structure analysis and actual beam interaction process observation.
Moessbauer studies of the LiAl sub(5-x) Fe sub(x) O8 and LiGa sub(5-x) Fe sub(x) O8 systems
International Nuclear Information System (INIS)
Barthem, V.M.T.S.; Maria Neto, J.; Souza Barros, F. de
1982-01-01
Comparative Moessbauer studies of the LiGa sub(5-x) Fe sub(x) O 8 and LiAl sub(5-x) Fe sub(x) O 8 systems are shown. The characteristics of the Moessbauer spectra, obtained with LiGa 5 O 8 samples with 0,1% of Fe 3+ , differ drastically from that observed with LiAl 5 O 8 with the same three-valent iron concentration. All these differences are related to the more covalent character of the gallium-oxygen binding, when compared with the aluminium-oxygen one. (L.C.) [pt
Thermodynamic Description Of Ternary Fe-B-X Systems. Part 2: Fe-B-Ni
Directory of Open Access Journals (Sweden)
Miettinen J.
2014-06-01
Full Text Available Przedstawiono termodynamiczny opis trójskładnikowego układu Fe-B-Ni w kontekście nowej bazy danych dla układów Fe-B-X (X = Cr, Ni, Mn, Si, Ti, V, C. Parametry termodynamiczne dwuskładnikowych stopów Fe-B. Fe-Ni i B-Ni zostały są zaczerpnięte z wcześniejszych opracowań, przy tym opis B-Ni został nieznacznie zmodyfikowany. Parametry dla układu Fe-B-Ni zostały zoptymalizowane w tej pracy w oparciu o eksperymentalne równowagi fazowe i dane termodynamiczne zaczerpnięte z literatury. Roztwory stałe w układzie Fe-B-Ni opisano przy użyciu modelu roztworu substytucyjnego, a borki traktowane są jako fazy stechiometryczne lub półstechiometryczne typu (A.BpCq opisane przy użyciu modelu dwu podsieci.
Temperature dependence of the interfacial magnetic anisotropy in W/CoFeB/MgO
Directory of Open Access Journals (Sweden)
Kyoung-Min Lee
2017-06-01
Full Text Available The interfacial perpendicular magnetic anisotropy in W/CoFeB (1.2 ∼ 3 nm/MgO thin film structures is strongly dependent on temperature, and is significantly reduced at high temperature. The interfacial magnetic anisotropy is generally proportional to the third power of magnetization, but an additional factor due to thermal expansion is required to explain the temperature dependence of the magnetic anisotropy of ultrathin CoFeB films. The reduction of the magnetic anisotropy is more prominent for the thinner films; as the temperature increases from 300 K to 400 K, the anisotropy is reduced ∼50% for the 1.2-nm-thick CoFeB, whereas the anisotropy is reduced ∼30% for the 1.7-nm-thick CoFeB. Such a substantial reduction of magnetic anisotropy at high temperature is problematic for data retention when incorporating W/CoFeB/MgO thin film structures into magneto-resistive random access memory devices. Alternative magnetic materials and structures are required to maintain large magnetic anisotropy at elevated temperatures.
Crystallization study of amorphous system Fe[sub 84-x]W[sub x]B[sub 16] (x = 3; 5)
Energy Technology Data Exchange (ETDEWEB)
Novakova, A.A.; Sidorova, G.V.; Kiseleva, T.Yu.; Szasz, A. (Dept. of Physics, State Univ., Moscow (Russia) Inst. of Metallurgy, Academy of Science, Moscow (Russia) Eoetvoes Univ., Budapest (Hungary))
1992-10-01
A complex study of the crystallization process of the amorphous system was carried out by Moessbauer spectroscopy, X-ray diffraction and DTA. Alloy samples crystallized at 600deg C contain the following phases: [alpha]-Fe, Fe[sub 3]B and solid solution (Fe, W)[sub 3]B. (orig.).
Phase diagrams from ab-initio calculations: Re-W and Fe-B
Energy Technology Data Exchange (ETDEWEB)
Hammerschmidt, Thomas; Bialon, Arthur; Palumbo, Mauro; Fries, Suzana G.; Drautz, Ralf [ICAMS, Ruhr-Universitaet Bochum (Germany)
2011-07-01
The CALPHAD (CaLculation of Phase Diagrams) method relies on Gibbs energy databases and is of limited predictive power in cases where only limited experimental data is available for constructing the Gibbs energy databases. This is problematic for, e.g., the calculation of the phase transformation kinetics within phase field simulations that not only require the thermodynamic equilibrium data but also information on metastable phases. Such information is difficult to obtain directly from experiment but ab-initio calculations may supplement experimental databases as they comprise metastable phases and arbitrary chemical compositions. We present simulations for two prototypical systems: Re-W and Fe-B. For both systems we calculate the heat of formation for an extensive set of structures using ab-initio calculations and employ the total energies in CALPHAD in order to determine the corresponding phase diagrams. We account for the configurational entropy within the Bragg-Williams approximation and neglect the phenomenological excess-term that is commonly used in CALPHAD as well as the contribution of phonons and electronic excitations to the free energy. According to our calculations the complex intermetallic phases in Re-W are stabilized by the configurational entropy. For Fe-B, we calculate metastable and stable phase diagrams including recently predicted new stable phases.
Study of Moessbauer effect on LiFe5-x Alx O8, LiFe 5-x Gax O8 and LiGa5-x Fex O8 systems
International Nuclear Information System (INIS)
Barthem, V.M.T.S.
1982-01-01
The measures obtained by Moessbauer spectroscopy from LiFe 5-x Ga x O 8 and LiFe 5-x Al x O 8 systems are presented. A comparative study of the influences of dopant diamagnetic ions on magnetic structures of lithium ferrite was performed. The LiGa 5-x Fe x O 8 systems were analysed based on the existing data from LiAl 5-x Fe x O 8 systems, otaining informations about the iron ion behaviour in both matrices. (M.C.K.) [pt
Preparation, thermal stability, and magnetic properties of Fe-Zr-Mo-W-B bulk metallic glass
International Nuclear Information System (INIS)
Liu, D.Y.; Sun, W.S.; Wang, A.M.; Zhang, H.F.; Hu, Z.Q.
2004-01-01
A bulk metallic glass (BMG) cylinder of Fe 60 Co 8 Zr 10 Mo 5 W 2 B 15 with a diameter of 1.5 mm was prepared by copper mould casting of industrial raw materials. The amorphous state and the crystallization behavior were investigated by X-ray diffraction (XRD). The thermal stability parameters, such as glass transition temperature (T g ), crystallization temperature (T x ), supercooled liquid region (ΔT x ) between T g and T x , and reduced glass transition temperature T rg (T g /T m ) were measured by differential scanning calorimetry (DSC) to be 891, 950, 59 K, and 0.62, respectively. The crystallization process took place through a single stage, and involved crystallization of the phases α-Fe, ZrFe 2 , Fe 3 B, MoB 2 , Mo 2 FeB 2 , and an unknown phase, as determined by X-ray analysis of the sample annealed for 1.5 ks at 1023 K, 50 K above the DSC peak temperature of crystallization. Moessbauer spectroscopy was studied for this alloy. The spectra exhibit a broadened and asymmetric doublet-like structure that indicated paramagnetic behavior and a fully amorphous structure. α-Fe was found in the amorphous matrix for a cylinder with a diameter of 2.5 mm. The success of synthesis of the Fe-based bulk metallic glass from industrial materials is important for the future progress in research and practical application of new bulk metallic glasses
On the structural and magnetic properties of amorphous Fe84-xWxB16 alloys in dependence of W content
International Nuclear Information System (INIS)
Novakova, A.A.; Sidorova, G.V.; Katsnelson, A.A.; Szasz, A.; Kojnok, J.
1990-01-01
A series of rapidly solidificated amorphous Fe 84-x W x B 16 (x=0-5) alloys have been studied. A strictly linear decrease of H eff versus concentration of W has been observed by Moessbauer spectroscopy. (orig.)
Energy Technology Data Exchange (ETDEWEB)
Wang, W.-M. [Institute for Metallic Materials, IFW Dresden, P.O. 270016, Dresden D-01171 (Germany); Key Lab of Liquid Structure and Heredity of Materials, Shandong University, Jinan 250061 (China); Gebert, A. [Institute for Metallic Materials, IFW Dresden, P.O. 270016, Dresden D-01171 (Germany)], E-mail: a.gebert@ifw-dresden.de; Roth, S.; Kuehn, U.; Schultz, L. [Institute for Metallic Materials, IFW Dresden, P.O. 270016, Dresden D-01171 (Germany)
2008-07-14
This paper presents investigations on the effect of Si on the glass-forming ability, thermal stability and magnetic properties of the Fe-Co-Zr-Mo-W-B samples (group I: Fe{sub 60}Co{sub 8}Zr{sub 10}Mo{sub 5}W{sub 2}B{sub 15-x}Si{sub x}, 1 {<=} x {<=} 4; group II: Fe{sub 60}Co{sub 8}Zr{sub 10-x}Mo{sub 5}W{sub 2}B{sub 15}Si{sub x}, 0 {<=} x {<=} 4; group III: Fe{sub 60}Co{sub 8}Zr{sub 8}Mo{sub 5}W{sub 2}B{sub 17-x}Si{sub x}, 0 {<=} x {<=} 2) prepared by melt spinning, injection casting, and centrifugal casting methods. It is found that the glass-forming ability (GFA) of the alloys in group I is more deteriorated than that in group II, and that the alloys in group III can be cast into the rods of 1-3 mm diameter without crystalline reflections in their XRD patterns. For the amorphous ribbons and rods, a non-monotonic change of the nearest neighbour distance r{sub 1} with increasing Si content c{sub Si} was detected, which is parallel to that of the glass transition and crystallization temperatures T{sub g} and T{sub x}, but opposite to that of the magnetization at room temperature M{sub RT} and the Curie temperature T{sub c}. This correlation can be interpreted by a structure model presuming that iron atoms appear simultaneously in two types of local structures in the amorphous samples.
Cho, Soonha; Baek, Seung-heon Chris; Lee, Kyeong-Dong; Jo, Younghun; Park, Byong-Guk
2015-01-01
The phenomena based on spin-orbit interaction in heavy metal/ferromagnet/oxide structures have been investigated extensively due to their applicability to the manipulation of the magnetization direction via the in-plane current. This implies the existence of an inverse effect, in which the conductivity in such structures should depend on the magnetization orientation. In this work, we report a systematic study of the magnetoresistance (MR) of W/CoFeB/MgO structures and its correlation with the current-induced torque to the magnetization. We observe that the MR is independent of the angle between the magnetization and current direction but is determined by the relative magnetization orientation with respect to the spin direction accumulated by the spin Hall effect, for which the symmetry is identical to that of so-called the spin Hall magnetoresistance. The MR of ~1% in W/CoFeB/MgO samples is considerably larger than those in other structures of Ta/CoFeB/MgO or Pt/Co/AlOx, which indicates a larger spin Hall angle of W. Moreover, the similar W thickness dependence of the MR and the current-induced magnetization switching efficiency demonstrates that MR in a non-magnet/ferromagnet structure can be utilized to understand other closely correlated spin-orbit coupling effects such as the inverse spin Hall effect or the spin-orbit spin transfer torques. PMID:26423608
Hao, Qiang; Xiao, Gang
2015-03-01
We obtain robust perpendicular magnetic anisotropy in a β -W /Co40Fe40B20/MgO structure without the need of any insertion layer between W and Co40Fe40B20 . This is achieved within a broad range of W thicknesses (3.0-9.0 nm), using a simple fabrication technique. We determine the spin Hall angle (0.40) and spin-diffusion length for the bulk β form of tungsten with a large spin-orbit coupling. As a result of the giant spin Hall effect in β -W and careful magnetic annealing, we significantly reduce the critical current density for the spin-transfer-torque-induced magnetic switching in Co40Fe40B20 . The elemental β -W is a superior candidate for magnetic memory and spin-logic applications.
Crystalline-to-amorphous phase transformation in mechanically alloyed Fe50W50 powders
International Nuclear Information System (INIS)
Sherif El-Eskandarany, M.S.; Sumiyama, K.; Suzuki, K.
1997-01-01
A mechanical alloying process via a ball milling technique has been applied for preparing amorphous Fe 50 W 50 alloy powders. The results have shown that during the first and second stages of milling (0 to 360 ks) W atoms emigrate to Fe lattices to form nanocrystalline b.c.c. Fe-W solid solution, with a grain size of about 7 nm in diameter. After 720 ks of the milling time, this solid solution was transformed to an amorphous Fe-W alloy coexisting with the residual fraction of the unprocessed W powders. During the last stage of milling (720 to 1,440 ks) all of this residual W powder reacts with the amorphous phase to form a homogeneous Fe 50 W 50 amorphous alloy. The crystallization temperature and the enthalpy change of crystallization of amorphous Fe 50 W 50 powders milled for 1,440 ks were measured to be 860 K and -9kJ/mol, respectively. The amorphous Fe 50 W 50 powder produced is almost paramagnetic at room temperature. The powder comprises homogeneous and smooth spheres with an average size of about 0.5 microm in diameter
Directory of Open Access Journals (Sweden)
Rodrigo Freitas Guimarães
2010-12-01
Full Text Available Aços Cr-Mo são usados na indústria do petróleo em aplicações com óleos crus ricos em compostos sulfurosos. Aços comerciais como 2.5Cr1Mo ou 9Cr1Mo têm se mostrado ineficientes em consequência de altos índices de corrosão naftênica. Uma estratégia para resolver este problema é o aumento do teor de molibdênio destes aços. Neste trabalho foi estudado o efeito do aumento do teor de molibdênio na microestrutura de ligas Fe-9Cr-xMo, solubilizadas e soldadas. Foram levantados os diagramas de fases com auxílio de um programa comercial para verificar as possíveis fases a serem formadas e identificar os problemas de soldagem. A microestrutura das ligas solubilizadas foi analisada por microscopia óptica e EBSD, além da medição da dureza. Foram realizadas soldagens autógenas para verificar o efeito do aporte térmico na microestrutura e na dureza das ligas. O aumento do teor de molibdênio resultou no aumento da dureza das ligas. A análise microestrutural das ligas soldadas apresentou uma particularidade para a liga com menor teor de molibdênio, a presença de martensita. Já as ligas com maior teor de molibdênio apresentaram uma microestrutura completamente ferrítica. A formação de martensita pode ser um problema na solda da liga com menor teor de molibdênio, uma vez que a mesma pode causar perdas nas propriedades mecânicas comprometendo sua aplicação.Cr-Mo steels are used in the petroleum industry in applications with crude oils rich in sulfur compounds. 2.5Cr1Mo or 9Cr1Mo do not resist to operating conditions when in contact with crude oils. The increasing of molybdenum content can improve the corrosion resistance of these alloys. This paper studied the effect of increased concentration of molybdenum in the microstructure of Fe-9Cr-xMo alloys, annealed and welded. Phase diagrams were built with the aid of commercial program to check the possible phases to be formed and to identify the problems of welding. Analyses were
Castiblanco-Valencia, Mónica M; Fraga, Tatiana R; Breda, Leandro C D; Vasconcellos, Sílvio A; Figueira, Cláudio P; Picardeau, Mathieu; Wunder, Elsio; Ko, Albert I; Barbosa, Angela S; Isaac, Lourdes
2016-05-01
Leptospiral immunoglobulin-like (Lig) proteins are surface exposed molecules present in pathogenic but not in saprophytic Leptospira species. We have previously shown that Lig proteins interact with the soluble complement regulators Factor H (FH), FH like-1 (FHL-1), FH related-1 (FHR-1) and C4b Binding Protein (C4BP). In this study, we used the saprophyte L. biflexa serovar Patoc as a surrogate host to address the specific role of LigA and LigB proteins in leptospiral complement evasion. L. biflexa expressing LigA or LigB was able to acquire FH and C4BP. Bound complement regulators retained their cofactor activities of FI in the proteolytic cleavage of C3b and C4b. Moreover, heterologous expression of ligA and ligB genes in the saprophyte L. biflexa enhanced bacterial survival in human serum. Complement deposition on lig-transformed L. biflexa was assessed by flow cytometry analysis. With regard to MAC deposition, L. biflexa expressing LigA or LigB presented an intermediate profile: MAC deposition levels were greater than those found in the pathogenic L. interrogans, but lower than those observed for L. biflexa wildtype. In conclusion, Lig proteins contribute to in vitro control of complement activation on the leptospiral surface, promoting an increased bacterial survival in human serum. Copyright © 2016 European Federation of Immunological Societies. All rights reserved.
Thermodynamics of the Mo-Fe-C and W-Fe-C systems
International Nuclear Information System (INIS)
Kleykamp, H.
1978-01-01
A study on the reaction behaviour of the components of the Mo 2 C-Fe and WC-Fe systems is presented. Both systems are stable if the mono-phase carbides are in equilibrium with the Fe-C solid solution within fixed carbon concentrations, the limits of which are calculated in this paper. Gibbs energies of formation at 1273 K of the intermetallic phases, of the binary and of the ternary carbides in the Mo-Fe-C and W-Fe-C systems were determined. The Fe corner in the phase diagrams of both systems and the calculated C boundaries in the two-phase field γ-Fe(Mo,C)-Mo 2 C and the γ-Fe(W,C)-WC, respectively, based on this study, are shown in figures. (GSC) [de
MFM study of NdFeB and NdFeB/Fe/NdFeB thin films
International Nuclear Information System (INIS)
Gouteff, P.C.; Folks, L.; Street, R.
1998-01-01
Domain structures of NdFeB thin films, ranging in thickness between 1500 and 29 nm, have been studied qualitatively by magnetic force microscopy (MFM). Samples were prepared using a range of sputtering conditions resulting in differences in properties such as texture, coercivity and magnetic saturation. MFM images of all the films showed extensive interaction domain structures, similar to those observed in nanocrystalline bulk NdFeB. An exchange-coupled NdFeB/Fe/NdFeB trilayer with layer thicknesses 18 nm/15 nm/18 nm, respectively, was also examined using MFM. (orig.)
Note: Erosion of W-Ni-Fe and W-Cu alloy electrodes in repetitive spark gaps.
Wu, Jiawei; Han, Ruoyu; Ding, Weidong; Qiu, Aici; Tang, Junping
2018-02-01
A pair of W-Ni-Fe and W-Cu electrodes were tested under 100 kA level pulsed currents for 10 000 shots, respectively. Surface roughness and morphology characteristics of the two pairs of electrodes were obtained and compared. Experimental results indicated cracks divided the W-Cu electrode surface to polygons while the W-Ni-Fe electrode surface remained as a whole with pits and protrusions. Accordingly, the surface roughness of W-Ni-Fe electrodes increased to ∼3 μm while that of W-Cu electrodes reached ∼7 μm at the end of the test. The results reveal that the W-Ni-Fe alloy has a better erosion resistance and potential to be further applied in spark gaps.
Energy Technology Data Exchange (ETDEWEB)
Khalifa, Hesham E.; Cheney, Justin L. [University of California, San Diego Materials Science and Engineering Program, 9500 Gilman Drive, La Jolla, CA 92093-0411 (United States); Vecchio, Kenneth S. [University of California, San Diego Department of NanoEngineering, 9500 Gilman Drive, La Jolla, CA 92093-0411 (United States)], E-mail: kvecchio@ucsd.edu
2008-08-25
Amorphous Fe{sub 67-x}C{sub 10}B{sub 9}Mo{sub 7+x}Cr{sub 4}W{sub 3} (x = 1-7 at.%) plates with 640 {mu}m thickness were prepared by copper mold casting. The thermal properties and microstructural development during heat treatments were investigated by a combination of differential scanning calorimetry (DSC), differential thermal analysis, and X-ray diffractometry (XRD). The glass forming ability (GFA) and activation energy for crystallization have a distinct dependence on Mo content. Fe{sub 62}C{sub 10}B{sub 9}Mo{sub 12}Cr{sub 4}W{sub 3} is the best glass former in this study, demonstrating a supercooled liquid region, {delta}T{sub x} = 51 K, and an activation energy for crystallization, Q = 453 kJ/mol. The GFA of alloys in this system was governed by elastic strain optimization resulting directly from the variation in Mo content. Heat treatments were performed to demonstrate resistance to crystallization under typical processing conditions. Alloys in this system exhibited a three-phase evolution during crystallization. A second set of heat treatments was performed to identify each phase. Hardness data was collected at each of the heat treatment conditions, and a bulk metallic glasses (BMG)-derived composite containing a Mo-rich phase exhibited Vickers Hardness in excess of 2000. The fully amorphous alloys had an average hardness approaching 1500.
Figueira, Cláudio Pereira; Croda, Julio; Choy, Henry A; Haake, David A; Reis, Mitermayer G; Ko, Albert I; Picardeau, Mathieu
2011-06-09
In comparison to other bacterial pathogens, our knowledge of the molecular basis of the pathogenesis of leptospirosis is extremely limited. An improved understanding of leptospiral pathogenetic mechanisms requires reliable tools for functional genetic analysis. Leptospiral immunoglobulin-like (Lig) proteins are surface proteins found in pathogenic Leptospira, but not in saprophytes. Here, we describe a system for heterologous expression of the Leptospira interrogans genes ligA and ligB in the saprophyte Leptospira biflexa serovar Patoc. The genes encoding LigA and LigB under the control of a constitutive spirochaetal promoter were inserted into the L. biflexa replicative plasmid. We were able to demonstrate expression and surface localization of LigA and LigB in L. biflexa. We found that the expression of the lig genes significantly enhanced the ability of transformed L. biflexa to adhere in vitro to extracellular matrix components and cultured cells, suggesting the involvement of Lig proteins in cell adhesion. This work reports a complete description of the system we have developed for heterologous expression of pathogen-specific proteins in the saprophytic L. biflexa. We show that expression of LigA and LigB proteins from the pathogen confers a virulence-associated phenotype on L. biflexa, namely adhesion to eukaryotic cells and fibronectin in vitro. This study indicates that L. biflexa can serve as a surrogate host to characterize the role of key virulence factors of the causative agent of leptospirosis.
Directory of Open Access Journals (Sweden)
Xin Liu
2017-04-01
Full Text Available The effects of tungsten addition on the microstructure and corrosion resistance of Fe-3.5B alloys in a liquid zinc bath at 520 °C were investigated by means of scanning electron microscopy, X-ray diffraction and electron probe micro-analysis. The microstructure evolution in different alloys is analyzed and discussed using an extrapolated Fe-B-W ternary phase diagram. Experimental results show that there are three kinds of borides, the reticular (Fe, W2B, the rod-like (Fe, W3B and flower-like FeWB. The addition of tungsten can refine the microstructure and improve the stability of the reticular borides. Besides, it is beneficial to the formation of the metastable (Fe, W3B phase. The resultant Fe-3.5B-11W (wt % alloy possesses excellent corrosion resistance to liquid zinc. When tungsten content exceeds 11 wt %, the formed flower-like FeWB phase destroys the integrity of the reticular borides and results in the deterioration of the corrosion resistance. Also, the corrosion failure resulting from the spalling of borides due to the initiation of micro-cracks in the grain boundary of borides is discussed in this paper.
Pappas, Christopher J; Picardeau, Mathieu
2015-11-01
Leptospirosis is a zoonotic disease that affects ∼1 million people annually, with a mortality rate of >10%. Currently, there is an absence of effective genetic manipulation tools for targeted mutagenesis in pathogenic leptospires. Transcription activator-like effectors (TALEs) are a recently described group of repressors that modify transcriptional activity in prokaryotic and eukaryotic cells by directly binding to a targeted sequence within the host genome. To determine the applicability of TALEs within Leptospira spp., two TALE constructs were designed. First, a constitutively expressed TALE gene specific for the lacO-like region upstream of bgaL was trans inserted in the saprophyte Leptospira biflexa (the TALEβgal strain). Reverse transcriptase PCR (RT-PCR) analysis and enzymatic assays demonstrated that BgaL was not expressed in the TALEβgal strain. Second, to study the role of LigA and LigB in pathogenesis, a constitutively expressed TALE gene with specificity for the homologous promoter regions of ligA and ligB was cis inserted into the pathogen Leptospira interrogans (TALElig). LigA and LigB expression was studied by using three independent clones: TALElig1, TALElig2, and TALElig3. Immunoblot analysis of osmotically induced TALElig clones demonstrated 2- to 9-fold reductions in the expression levels of LigA and LigB, with the highest reductions being noted for TALElig1 and TALElig2, which were avirulent in vivo and nonrecoverable from animal tissues. This study reconfirms galactosidase activity in the saprophyte and suggests a role for LigA and LigB in pathogenesis. Collectively, this study demonstrates that TALEs are effective at reducing the expression of targeted genes within saprophytic and pathogenic strains of Leptospira spp., providing an additional genetic manipulation tool for this genus. Copyright © 2015, American Society for Microbiology. All Rights Reserved.
International Nuclear Information System (INIS)
Pudji Irasari; Novrita Idayanti
2009-01-01
Designing and manufacturing of low speed permanent magnet generator (PMG) for small scale electric power plant have been conducted. In this paper, the characteristics of generator using permanent magnet of barium ferrite (BaFe 12 O 19 ) and neodymium iron boron (NdFeB) were compared. Surface mounted type is selected as the rotor structure as all flux faces to stator winding and take a role in energy conversion. The experiment result demonstrates that at nominal speed, generator with BaFe 12 O 19 magnet can only generate power of 8.87 W while generator with NdFeB magnet can generate power of 1,988.93 W. (author)
Crystallization study of amorphous system Fe84-xWxB16 (x = 3;5)
International Nuclear Information System (INIS)
Novakova, A.A.; Sidorova, G.V.; Kiseleva, T.Yu.; Szasz, A.
1992-01-01
A complex study of the crystallization process of the amorphous system was carried out by Moessbauer spectroscopy, X-ray diffraction and DTA. Alloy samples crystallized at 600deg C contain the following phases: α-Fe, Fe 3 B and solid solution (Fe, W) 3 B. (orig.)
Adhesive and Cohesive Strength in FeB/Fe2B Systems
Meneses-Amador, A.; Blancas-Pérez, D.; Corpus-Mejía, R.; Rodríguez-Castro, G. A.; Martínez-Trinidad, J.; Jiménez-Tinoco, L. F.
2018-05-01
In this work, FeB/Fe2B systems were evaluated by the scratch test. The powder-pack boriding process was performed on the surface of AISI M2 steel. The mechanical parameters, such as yield stress and Young's modulus of the boride layer, were obtained by the instrumented indentation technique. Residual stresses produced on the boride layer were estimated by using the x-ray diffraction (XRD) technique. The scratch test was performed in order to evaluate the cohesive/adhesive strength of the FeB/Fe2B coating. In addition, a numerical evaluation of the scratch test on boride layers was performed by the finite element method. Maximum principal stresses were related to the failure mechanisms observed by the experimental scratch test. Shear stresses at the interfaces of the FeB/Fe2B/substrate system were also evaluated. Finally, the results obtained provide essential information about the effect of the layer thickness, the residual stresses, and the resilience modulus on the cohesive/adhesive strength in FeB/Fe2B systems.
Özel, Cihan; Gürgenç, Turan
2018-01-01
In this study, AISI 1020 steel surface was coated in different heat inputs with (wt.-%) 50FeCrC-20FeW-30FeB powder mixture by using plasma transferred arc (PTA) welding method. The microstructure of the coated samples were investigated by using optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and energy dispersive X-ray (EDS). The hardness was measured with micro hardness test device. The dry sliding wear and friction coefficient properties were determined using a block-on-disk type wear test device. Wear tests were performed at 19.62 N, 39.24 N, 58.86 N load and the sliding distance of 900 m. The results were shown that different microstructures formed due to the heat input change. The highest average micro hardness value was measured at 1217 HV on sample coated with low heat input. It was determined that the wear resistance decreased with increasing heat input.
Corrosion behaviour of electrodeposited nanocrystalline Ni-W and Ni-Fe-W alloys
International Nuclear Information System (INIS)
Sriraman, K.R.; Ganesh Sundara Raman, S.; Seshadri, S.K.
2007-01-01
The present work deals with evaluation of corrosion behaviour of electrodeposited nanocrystalline Ni-W and Ni-Fe-W alloys. Corrosion behaviour of the coatings deposited on steel substrates was studied using polarization and electrochemical impedance spectroscopy techniques in 3.5% NaCl solution while their passivation behaviour was studied in 1N sulphuric acid solution. The corrosion resistance of Ni-W alloys increased with tungsten content up to 7.54 at.% and then decreased. In case of Ni-Fe-W alloys it increased with tungsten content up to 9.20 at.% and then decreased. The ternary alloy coatings exhibited poor corrosion resistance compared to binary alloy coatings due to preferential dissolution of iron from the matrix. Regardless of composition all the alloys exhibited passivation behaviour over a wide range of potentials due to the formation of tungsten rich film on the surface
UV-LIGA: From Development to Commercialization
Directory of Open Access Journals (Sweden)
Grégoire Genolet
2014-07-01
Full Text Available A major breakthrough in UV-LIGA (Lithographie, Galvanoformung and Abformung started with the use of epoxy-based EPON® SU-8 photoresist in the mid-1990s. Using this photoresist has enabled the fabrication of tall and high aspect ratio structures without the use of a very expensive synchrotron source needed to expose the photoresist layer in X-ray LIGA. SU-8 photoresist appeared to be well-suited for LIGA templates, but also as a permanent material. Based on UV-LIGA and SU-8, Mimotec SA has developed processes to manufacture mold inserts and metallic components for various market fields. From one to three-level parts, from Ni to other materials, from simple to complicated parts with integrated functionalities, UV-LIGA has established itself as a manufacturing technology of importance for prototyping, as well as for mass-fabrication. This paper reviews some of the developments that led to commercial success in this field.
Directory of Open Access Journals (Sweden)
Manterola, J.
1968-09-01
Full Text Available A structure, as a whole, consists of an organised set of material parts, whose structural significance depends both on their topological nature and on the external forces acting on them. This duality, that is typical of a structure, is related on the one hand to the structural forms that man can construct, and on the other to progressive adaptation of the structural topology to the external forces acting on it. The integrated study of the constructive process and of the theory of structures does not exhaust the problem of structures. The characteristics of the materials are still to be considered. The effect of these three factors on the cost depends on the dynamic evolution of these factors themselves: their importance being greater or smaller according to the evolutionary stage that is considered and the purpose of the structure. Furthermore, the structural significance of an object is influenced by the changes in the surrounding structural elements. Thus, a form, whose development might be determined strictly by structural motives at a given period, at another stage may no longer depend on structural factors. Hence structure is only a relative concept.En la estructura resistente, tomada como un todo, subyace una organización de elementos materiales, cuyo valor de posición viene condicionado tanto por las condiciones mecánicas de trabajo resistente que se establece entre ellas como por la posibilidad de manejar y colocar en su sitio el peso y volumen que determinan. Esta partición, contenido mismo de lo estructural, nos remite, por un lado, a las condiciones variables en que se concretan las posibilidades energéticas de la humanidad, y por otro, sitúa la estructura enfrentada a las acciones exteriores en una serie de etapas intermedias que para ser resistidas va a ser construida, lo que le proporciona la operatividad que reside en todo proceso de crecimiento. La integración del proceso constructivo y la teoría de lo resistente no agota
UV-LIGA technique for ECF micropumps using back UV exposure and self-alignment
Han, D.; Xia, Y.; Yokota, S.; Kim, J. W.
2017-12-01
This paper proposes and develops a novel UV-LIGA technique using back UV exposure and self-alignment to realize high aspect ratio micromachining (HARM) in high power density electro-conjugate fluid (ECF) micropumps. ECF is a functional fluid designed to be able to generate strong and active jet flow (ECF jetting) between anode and cathode in ECF when high DC voltage is applied. We have developed high power density ECF micropumps consisting of triangular prism and slit electrode pairs (TPSEs) fabricated by HARM. The traditional UV-LIGA technique for HARM is mainly divided into two approaches: (a) single thick layer and (b) multiple thin layers. Both methods have limitations—deformed molds in the former and misalignment between layers in the latter. Using the finite element method software COMSOL Multiphysics, we demonstrate that the deformed micro-molds critically impair the performance of ECF micropumps. In addition, we experimentally prove that the misalignment would easily trigger electric discharge in the ECF micropumps. To overcome these limitations, we conceive a new concept utilizing the seed electrode layer for electroforming as the UV shield and pattern photoresist (KMPR) by back UV exposure. The seed electrode layer should be composed of a non-transparent conductor (Au/Ti) for patterning and a transparent conductor (ITO) for wiring. Instead of ITO, we propose the concept of transparency-like electrodes comprised of thin metal line patterns. To verify this concept, KMPR layers with thicknesses of 70, 220, and 500 µm are experimentally investigated. In the case of 500 µm KMPR thickness, the concept of transparency-like electrode was partially proved. As a result, TPSEs with a height of 440 µm were successfully fabricated. Characteristic experiments demonstrated that ECF micropumps (367 mW cm-3) fabricated by back UV achieved almost the same output power density as ECF micropumps (391 mW cm-3) fabricated by front UV. This paper proves that the proposed
UV-LIGA technique for ECF micropumps using back UV exposure and self-alignment
International Nuclear Information System (INIS)
Han, D; Xia, Y; Yokota, S; Kim, J W
2017-01-01
This paper proposes and develops a novel UV-LIGA technique using back UV exposure and self-alignment to realize high aspect ratio micromachining (HARM) in high power density electro-conjugate fluid (ECF) micropumps. ECF is a functional fluid designed to be able to generate strong and active jet flow (ECF jetting) between anode and cathode in ECF when high DC voltage is applied. We have developed high power density ECF micropumps consisting of triangular prism and slit electrode pairs (TPSEs) fabricated by HARM. The traditional UV-LIGA technique for HARM is mainly divided into two approaches: (a) single thick layer and (b) multiple thin layers. Both methods have limitations—deformed molds in the former and misalignment between layers in the latter. Using the finite element method software COMSOL Multiphysics, we demonstrate that the deformed micro-molds critically impair the performance of ECF micropumps. In addition, we experimentally prove that the misalignment would easily trigger electric discharge in the ECF micropumps. To overcome these limitations, we conceive a new concept utilizing the seed electrode layer for electroforming as the UV shield and pattern photoresist (KMPR) by back UV exposure. The seed electrode layer should be composed of a non-transparent conductor (Au/Ti) for patterning and a transparent conductor (ITO) for wiring. Instead of ITO, we propose the concept of transparency-like electrodes comprised of thin metal line patterns. To verify this concept, KMPR layers with thicknesses of 70, 220, and 500 µ m are experimentally investigated. In the case of 500 µ m KMPR thickness, the concept of transparency-like electrode was partially proved. As a result, TPSEs with a height of 440 µ m were successfully fabricated. Characteristic experiments demonstrated that ECF micropumps (367 mW cm −3 ) fabricated by back UV achieved almost the same output power density as ECF micropumps (391 mW cm −3 ) fabricated by front UV. This paper proves that the
Structural and magnetic properties of NdFeB and NdFeB/Fe films with Mo addition
Energy Technology Data Exchange (ETDEWEB)
Urse, M; Grigoras, M; Lupu, N; Chiriac, H, E-mail: urse@phys-iasi.ro [National Institute of R and D for Technical Physics, 47 Mangeron Blvd., 700050 Iasi (Romania)
2011-07-06
The influence of the Mo addition on the microstructure and magnetic properties of Nd-Fe-B and Nd-Fe-B/Fe films was studied. The coercivity is a key parameter in the control of technical performances of Nd-Fe-B films. A small amount of about 1 at.% Mo can enhance the coercivity of Nd-Fe-B film by controlling the growth of soft and hard magnetic grains. A coercivity of 22.1 kOe, a remanence ratio, M{sub r}/M{sub s}, of 0.83 and a maximum energy product of 8 MGOe were obtained for Ta/[NdFeBMo(1at.%)(540nm)/Ta films annealed at 650{sup 0}C for 20 minutes due to Mo precipitates formed at the Nd{sub 2}Fe{sub 14}B phase boundaries which prevent the nucleation and expansion of the magnetic domains. Simultaneous use of Mo as addition and the stratification of Nd-Fe-B-Mo films using Fe as spacer layer are important tools for the improvement of the hard magnetic properties of Nd-Fe-B films. The Ta/[NdFeBMo(1at.%)(180nm)/Fe(1nm)]x3/Ta multilayer film annealed at 620{sup 0}C exhibits an increase in the coercivity from 12.1 kOe to 22.8 kOe, in the remanence ratio from 0.77 to 0.80, and in the maximum energy product from 4.5 to 7.1 MGOe in comparison with Ta/Nd-Fe-B/Ta film. As compared to Ta/Nd-Fe-B/Ta film, the Ta/[NdFeBMo(1at.%)(180nm)/Fe(1nm)]x3/Ta film presents a decrease in the crystallization temperature of about 30{sup 0}C.
Mechanical properties of Fe-Ni-Cr-Si-B bulk glassy alloy
International Nuclear Information System (INIS)
Lee, Kee Ahn; Kim, Yong Chan; Kim, Jung Han; Lee, Chong Soo; Namkung, Jung; Kim, Moon Chul
2007-01-01
The mechanical properties and crystallization behavior of new Fe-Ni-Cr-Si-B-based bulk glassy alloys were investigated. The suitability of the continuous roll casting method for the production of bulk metallic glass (BMG) sheets in such alloy systems was also examined. BMG samples (Fe-Ni-Cr-Si-B, Fe-Ni-Zr-Cr-Si-B, Fe-Ni-Zr-Cr-W-Si-B) in amorphous strip, cylindrical, and sheet forms were prepared through melt spinning, copper mold casting, and twin roll strip casting, respectively. Fe-Ni-Cr-Si-B alloy exhibited compressive strength of up to 2.93 GPa and plastic strain of about 1.51%. On the other hand, the Fe-Ni-Zr-Cr-Si-B, composite-type bulk sample with diameter of 2.0 mm showed remarkable compressive plastic strain of about 4.03%. The addition of zirconium was found to enhance the homogeneous precipitation of nanocrystalline less than 7 nm and to develop a hybrid-composite microstructure with increasing sample thickness. Twin roll strip casting was successfully applied to the fabrication of sheets in Fe-Ni-Cr-Si-B-based BMGs. The combined characteristics of high mechanical properties and ease of microstructure control proved to be promising in terms of the future progress of structural bulk amorphous alloys
Mechanical properties of Fe-Ni-Cr-Si-B bulk glassy alloy
Energy Technology Data Exchange (ETDEWEB)
Lee, Kee Ahn [School of Advanced Materials Engineering, Andong National University, Andong 760-749 (Korea, Republic of)]. E-mail: keeahn@andong.ac.kr; Kim, Yong Chan [New Metals Research Team, RIST, Pohang 790-330 (Korea, Republic of); Kim, Jung Han [Center for Advanced Aerospace materials, POSTECH, Pohang 790-784 (Korea, Republic of); Lee, Chong Soo [Center for Advanced Aerospace materials, POSTECH, Pohang 790-784 (Korea, Republic of); Namkung, Jung [New Metals Research Team, RIST, Pohang 790-330 (Korea, Republic of); Kim, Moon Chul [New Metals Research Team, RIST, Pohang 790-330 (Korea, Republic of)
2007-03-25
The mechanical properties and crystallization behavior of new Fe-Ni-Cr-Si-B-based bulk glassy alloys were investigated. The suitability of the continuous roll casting method for the production of bulk metallic glass (BMG) sheets in such alloy systems was also examined. BMG samples (Fe-Ni-Cr-Si-B, Fe-Ni-Zr-Cr-Si-B, Fe-Ni-Zr-Cr-W-Si-B) in amorphous strip, cylindrical, and sheet forms were prepared through melt spinning, copper mold casting, and twin roll strip casting, respectively. Fe-Ni-Cr-Si-B alloy exhibited compressive strength of up to 2.93 GPa and plastic strain of about 1.51%. On the other hand, the Fe-Ni-Zr-Cr-Si-B, composite-type bulk sample with diameter of 2.0 mm showed remarkable compressive plastic strain of about 4.03%. The addition of zirconium was found to enhance the homogeneous precipitation of nanocrystalline less than 7 nm and to develop a hybrid-composite microstructure with increasing sample thickness. Twin roll strip casting was successfully applied to the fabrication of sheets in Fe-Ni-Cr-Si-B-based BMGs. The combined characteristics of high mechanical properties and ease of microstructure control proved to be promising in terms of the future progress of structural bulk amorphous alloys.
Pulsed laser-deposited nanocrystalline GdB{sub 6} thin films on W and Re as field emitters
Energy Technology Data Exchange (ETDEWEB)
Suryawanshi, Sachin R.; More, Mahendra A. [Savitribai Phule Pune University, Department of Physics, Centre for Advanced Studies in Materials Science and Condensed Matter Physics, Pune (India); Singh, Anil K.; Sinha, Sucharita [Bhabha Atomic Research Centre, Laser and Plasma Technology Division, Trombay, Mumbai (India); Phase, Deodatta M. [UGC-DAE Consortium for Scientific Research Indore Centre, Indore (India); Late, Dattatray J. [CSIR-National Chemical Laboratory, Physical and Materials Chemistry Division, Pune (India)
2016-10-15
Gadolinium hexaboride (GdB{sub 6}) nanocrystalline thin films were grown on tungsten (W), rhenium (Re) tips and foil substrates using optimized pulsed laser deposition (PLD) technique. The X-ray diffraction analysis reveals formation of pure, crystalline cubic phase of GdB{sub 6} on W and Re substrates, under the prevailing PLD conditions. The field emission (FE) studies of GdB{sub 6}/W and GdB{sub 6}/Re emitters were performed in a planar diode configuration at the base pressure ∝10{sup -8} mbar. The GdB{sub 6}/W and GdB{sub 6}/Re tip emitters deliver high emission current densities of ∝1.4 and 0.811 mA/cm{sup 2} at an applied field of ∝6.0 and 7.0 V/μm, respectively. The Fowler-Nordheim (F-N) plots were found to be nearly linear showing metallic nature of the emitters. The noticeably high values of field enhancement factor (β) estimated using the slopes of the F-N plots indicate that the PLD GdB{sub 6} coating on W and Re substrates comprises of high-aspect-ratio nanostructures. Interestingly, the GdB{sub 6}/W and GdB{sub 6}/Re planar emitters exhibit excellent current stability at the preset values over a long-term operation, as compared to the tip emitters. Furthermore, the values of workfunction of the GdB{sub 6}/W and GdB6/Re emitters, experimentally measured using ultraviolet photoelectron spectroscopy, are found to be same, ∝1.6 ± 0.1 eV. Despite possessing same workfunction value, the FE characteristics of the GdB{sub 6}/W emitter are markedly different from that of GdB{sub 6}/Re emitter, which can be attributed to the growth of GdB{sub 6} films on W and Re substrates. (orig.)
Grazing incidence Fe-line telescopes using W/B4C multilayers
DEFF Research Database (Denmark)
Joensen, K. D.; Gorenstein, P.; Christensen, Finn Erland
1995-01-01
The loss of throughput observed at higher energies for traditional grazing-incidence X-ray telescopes coated with high-Z elements can be partly countered by employing multilayers on the outermost reflectors. Using 8-keV reflectivity data from a periodic W/B4C multilayer, the expected performance...
LOS ALMIDONES RESISTENTES Y LA SALUD
Directory of Open Access Journals (Sweden)
Carmen Carla Quiroga Ledezma
2009-01-01
Para una mejor comprensión de los almidones resistentes y su efecto en la salud se hizo una revisión bibliográfica de los trabajos publicados: estructura del almidón, tipos de modificaciones a la estructura del almidón, digestión del almidón, tipos de almidones, consecuencias fisiológicas del almidón resistente y tendencias futuras.
Directory of Open Access Journals (Sweden)
Rosa Navarrete
2000-01-01
Full Text Available Genotipos de frijol (Phaseolus vulgaris L. resistentes a Xanthomonas campestris pv. phaseoli de México. Durante 1995 se evaluó la reacción de genotipos de frijol de diversos origenes a Xcp, bajo condiciones de invernadero en el Campo Experimental del Valle de México, del INIFAP. Se realizaron tres experimentos con a120, b44 y csiete genotipos de frijol. Las plantas se inocularon por corte con navajas en la etapa V3, a y b con una mezcla de nueve cepas de Xcp y el c, con cada una de siete cepas con diferente grado de patogenicidad. La severidad se evaluó 20 días después de la inoculación, por comparación con una escala visual de nueve grados. Los datos se analizaron bajo un diseño completamente al azar. En a, los genotipos que mostraron reacción de resistencia a Xcp fueron: A 36, A 475, G 5686, G 11867, Harowood, SEA 14, XAN 266, MCD 4012 y REN 27. En b los genotipos resistentes fueron: Sequía Durango, Taylor y XAN 30. En los experimentos anteriores la severidad de la enfermedad mostró una distribución normal, con el máximo número de genotipos en el grado de severidad cinco en a y seis en b. Los resultados obtenidos indican que el uso de mezclas de cepas de bacterias con diferente patogenicidad es eficiente para identificar genotipos de frijol resistentes a Xcp. Los genotipos resistentes identificados en el último experimento, mostraron respuesta diferencial e interacciones genotipo por cepa. REN 27 y SEA 14 mostraron resistencia a las cepas utilizadas
Energy Technology Data Exchange (ETDEWEB)
Nowacki, J. [Wydzial Inzynierii Materialowej, Politechnika Szczecinska, Szczecin (Poland); Klimek, L. [Instytut Inzynierii Materialowej i Technik Bezwiorowych, Politechnika Lodzka, Lodz (Poland)
1998-12-31
The process of multiphase sintering of iron in the vacuum has been analysed. As a result of the process iron-iron boride cermets have been produced. Fe-Fe{sub 2}B cermets were obtained as a result of sintering of the Fe and B pure elements in the vacuum. Attemps at sintering in the solid phase and with the participation of the liquid phase, the Fe-Fe{sub 2}B eutectic, have been made. Metallographic qualitative and quantitative studies, X-ray structural qualitative and qauantitative analysis allowed to determine the structure of Fe{sub 2}B cermets, as well as a description of the kinetics of quantitative changes in phase proportions in the course of sintering. It has been found that their structure varies widely depending on sintering parameters and the composition of the sinters. Measurements of the Fe-Fe{sub 2}B cermets hardness and measurements on wear during dry friction by the pin-on-disc method have shown distinct advantages of the cermets as a modern constructional materials. The hardness of Fe-Fe{sub 2}B cermets, depending on their chemical composition and sintering parameters, ranges widely from 150 to 1500 HV, and their resistance to wear is comparable to that of diffusively boronized steels. FeFe{sub 2}B cermets are a composite material in which iron boride, Fe{sub 2}B, with a hardness of about 1800 HV plays the role of the reinforcement,while iron-iron boride, Fe-Fe{sub 2}B, with a hardness of about 500 HV plays the role of matrix. The eutectic in the spaces between iron boride grains is composed of boron solid solution plates in iron with a hardness of arround 250 HV, and iron boride, Fe{sub 2}B, plates with a hardness of approximaly 1800 HV. The combination of such different materials, a hard reinforcement and a relatively plastic matrix produces favourable properties of the cermet thus produced high hardness (1500 HV) constant over whole cross section of the material, resistance of abrasive wear and acceptable ductility. The properties mentioned above
International Nuclear Information System (INIS)
Jiang Yonggang; Fujita, Takayuki; Uehara, Minoru; Iga, Yuki; Hashimoto, Taichi; Hao, Xiuchun; Higuchi, Kohei; Maenaka, Kazusuke
2011-01-01
The silicon molding technique is described for patterning of NdFeB/Ta multilayered magnetic films and NdFeB magnetic powder at the micron scale. Silicon trenches are seamlessly filled by 12-μm-thick NdFeB/Ta multilayered magnetic films with a magnetic retentivity of 1.3 T. The topography image and magnetic field distribution image are measured using an atomic force microscope and a magnetic force microscope, respectively. Using a silicon molding technique complemented by a lift-off process, NdFeB magnetic powder is utilized to fabricate magnetic microstructures. Silicon trenches as narrow as 20 μm are filled by a mixture of magnetic powder and wax powder. The B-H hysteresis loop of the patterned magnetic powder is characterized using a vibrating sample magnetometer, which shows a magnetic retentivity of approximately 0.37 T. - Highlights: → We demonstrate the fabrication of micro-magnets using silicon molding processes. → NdFeB/Ta films are well filled in silicon trenches with a thickness of 12 μm. → The 12-μm-thick NdFeB/Ta magnetic film shows a retentivity of 1.3 T. → Magnetic structures as narrow as 20 μm are fabricated using NdFeB magnetic powder. → VSM measurement shows a retentivity of 0.37 T for patterned NdFeB magnetic powder.
Energy Technology Data Exchange (ETDEWEB)
Jiang Yonggang, E-mail: yonggangj@gmail.com [School of Mechanical Engineering and Automation, Beihang University, Xueyuan Road No. 37, Haidian District, Beijing 100191 (China); Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Fujita, Takayuki [Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Graduate School of Engineering, University of Hyogo, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Uehara, Minoru [NEOMAX Co. Ltd., 2-15-17, Egawa, Shimamoto-Cho, Mishima-gun, Osaka 618-0013 (Japan); Iga, Yuki [Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Hashimoto, Taichi [Graduate School of Engineering, University of Hyogo, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Hao, Xiuchun; Higuchi, Kohei [Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Maenaka, Kazusuke [Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Graduate School of Engineering, University of Hyogo, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan)
2011-11-15
The silicon molding technique is described for patterning of NdFeB/Ta multilayered magnetic films and NdFeB magnetic powder at the micron scale. Silicon trenches are seamlessly filled by 12-{mu}m-thick NdFeB/Ta multilayered magnetic films with a magnetic retentivity of 1.3 T. The topography image and magnetic field distribution image are measured using an atomic force microscope and a magnetic force microscope, respectively. Using a silicon molding technique complemented by a lift-off process, NdFeB magnetic powder is utilized to fabricate magnetic microstructures. Silicon trenches as narrow as 20 {mu}m are filled by a mixture of magnetic powder and wax powder. The B-H hysteresis loop of the patterned magnetic powder is characterized using a vibrating sample magnetometer, which shows a magnetic retentivity of approximately 0.37 T. - Highlights: > We demonstrate the fabrication of micro-magnets using silicon molding processes. > NdFeB/Ta films are well filled in silicon trenches with a thickness of 12 {mu}m. > The 12-{mu}m-thick NdFeB/Ta magnetic film shows a retentivity of 1.3 T. > Magnetic structures as narrow as 20 {mu}m are fabricated using NdFeB magnetic powder. > VSM measurement shows a retentivity of 0.37 T for patterned NdFeB magnetic powder.
OCORRÊNCIA E CARACTERIZAÇÃO DO AMIDO RESISTENTE EM AMIDOS DE MILHO E DE BANANA
Directory of Open Access Journals (Sweden)
Teixeira Maria A.V.
1998-01-01
Full Text Available No presente trabalho foi estudada a ocorrência de Amido Resistente (AR em amidos de milho e de banana (naturalmente resistente e investigado o efeito das variáveis: umidade de condicionamento, tempo e temperatura de armazenamento dos géis, na formação do AR em amido normal de milho; além das características físico-químicas e a estrutura fina do AR de milho e de banana. Foi observado que o teor de AR em amidos de milho e banana (2,5% e 49,61%, respectivamente parece não estar relacionada com a composição química do grânulo. O amido de banana apresentou grânulos com certo poliformismo, padrão de raio-x tipo B, além de uma fração linear de DP 34 resistente à b-amilólise. A estrutura cristalina que mantém o grânulo do amido de banana coeso, por si só, não explicou o alto teor de AR encontrado. O amido de milho normal apresentou formas poliédricas e padrão difração em raio-x tipo A. Não foi observada a fração com DP 34 resistente à b-amilólise, apesar da sua maior coesividade quando comparado ao amido de banana. O tratamento hidrotérmico aplicado no amido normal de milho quase triplicou o teor de AR (7,15% devido à formação de estruturas cristalinas coesas. O AR de milho (7,15% de AR, constituído por fragmentos porosos, apresentou padrão de difração tipo C. A não significância do tempo de armazenamento dos géis na produção do AR e a fração linear com DP 34 resistente à b-amilólise presente nos cromatogramas, sugerem a participação da amilose na formação desta estrutura resistente.
Chemical synthesis of magnetic Fe-B and Fe-Co-B particles and chains
International Nuclear Information System (INIS)
Fulmer, P.; Kim, J.; Manthiram, A.; Sanchez, J.M.
1999-04-01
With an objective to develop magnetic materials with high saturation magnetization for the Magnetically Assisted Chemical Separation (MACS) process the chemical synthesis of Fe-B and Fe-Co-B alloys by reducing iron and cobalt chloride solutions with potassium borohydride has been investigated systematically. The influence of the concentration of the reactants, applied magnetic field, reaction atmosphere, and method of mixing the reactants on the microstructure, particle size, composition and magnetic properties has been studied. Both M-B (M = Fe and Co) particles and elongated chains composed of nanometer size M-B particles have been obtained depending on the reaction conditions. The Fe-B samples exhibit saturation magnetization of M S of 120--190 emu/g, remanent magnetization M r of 10--22 emu/g, and coercive field H c of 400--900 Oe. A high M S value of 190 emu/g, which is close to the theoretical value of 218 emu/g for pure Fe, has been achieved particularly for samples with well-defined chain structures. Increasing the Co content in the Fe-Co-B alloys increases the boron content and thereby decreases the crystallinity and M S values although marginal increase in H c (1,250 Oe) and M r (36 emu/g) values could be made in some Fe-Co-B compositions. The chain structure with high M S may be attractive for other magnetic separation processes as well
International Nuclear Information System (INIS)
Tsunekawa, Koji; Choi, Young-Suk; Nagamine, Yoshinori; Djayaprawira, David D.; Takeuchi, Takashi; Kitamoto, Yoshitaka
2006-01-01
We report, for the first time, the correlation between tunneling magnetoresistance (TMR) and the microstructure of polycrystalline CoFeB/MgO/CoFeB magnetic tunnel junctions with various Co/Fe ratios in the (CoFe) 81 B 19 reference and free layers. It is found that the Co/Fe ratio in the (CoFe) 81 B 19 reference layer strongly affects the (001) out-of-plane texture of the MgO tunnel barrier, resulting in the variation in TMR ratio. Further microstructure characterization of the magnetic tunnel junction with a higher TMR ratio and a stronger (001) out-of-plane texture in the MgO tunnel barrier reveals a grain-to-grain lattice match between the crystallized bcc CoFeB reference layer and MgO with a 45deg rotational epitaxial relationship, that is, CoFeB(001)[110]//MgO(001)[100]. (author)
High saturation magnetization FeB(C) nanocapsules
International Nuclear Information System (INIS)
Ma, S.; Si, P.Z.; Zhang, Y.; Wu, B.; Li, Y.B.; Liu, J.J.; Feng, W.J.; Ma, X.L.; Zhang, Z.D.
2007-01-01
FeB(C) nanocapsules were prepared by arc-discharging Fe 80 B 20 alloy in Ar and CH 4 . X-ray diffraction and transmission electron microscopy analyses showed that the FeB(C) nanocapsules had a core-shell structure with α-Fe and Fe 3 B as cores and graphite as shells. The formation mechanism of the FeB(C) nanocapsules is discussed. The graphite shells display a strong anti-acid effect. The saturation magnetization at room temperature of the FeB(C) nanocapsules is much higher than that of Fe(B) nanocapsules. The blocking temperature of FeB(C) nanocapsules is above 300 K
Electronic Structures Localized at the Boron Atom in Amorphous Fe-B and Fe-B-P Alloys
Yasuda, Hidehiro; Nakayama, Hiroshi; Fujita, Hiroshi
1989-11-01
The electronic structures localized at the B in amorphous Fe-B and Fe-B-P alloys and their crystallized alloys were studied by Auger valence electron spectroscopy and the states of solute B are discussed based on the change in the degree of covalent bonding and the charge transfer between the Fe and B atoms. In amorphous phases, the charge transfers from Fe to B above 15at%B where B atoms occupy the substitutionallike situations, and from B to Fe below 15at%B where B atoms occupy the interstitiallike situations. Magnetic properties depend on such states of solute B. In crystalline phases, covalent bonding becomes dominant because the electron excitation occurs to the B2p state. Consequently, amorphous phases are more metallic in character than crystalline phases and amorphous structures are stabilized by a mixture of more than two different bonding states.
Pr2Fe14B/α-Fe nanocomposites for thermal applications
International Nuclear Information System (INIS)
Silva, Suelanny Carvalho da
2012-01-01
In this work, Pr x Fe 94 - x B 6 (x = 6, 8, 10 and 12) nanostructured powders were prepared by a combination of hydrogenation, disproportionation, desorption and recombination (HDDR) process with high energy milling applied to the mixture of an as-cast alloy (Pr 14 Fe 80 B 6 ) and α-Fe. The produced nanoparticles showed magnetic properties comparable to those reported in hyperthermia studies. The optimal time to obtain the magnetic nanoparticles is 5 hours (at 900 rpm). It was verified that longer milling times cause an increase in carbon percentage on the particles. The carbon is derived from oleic acid added as a surfactant in the milling step. The nanocomposites exhibit coercive force ranging from 80 Oe (6.5 kAm -1 ) to 170 Oe (13.5 kAm -1 ) and magnetic moments in the range of 81 129 Am2kg -1 . From the X-ray diffraction analyses, only two phases were found in all samples: α-Fe and the magnetic phase Pr 2 Fe 14 B. Individual nanoparticles with diameter of about 20 nm were verified. The samples studied presented heating when exposed to an alternating magnetic field (f = 222 kHz e H max ∼3.7 kAm -1 ) comparable to reported in literature. Temperature variations (ΔT) of the powders were: 51 K for Pr 6 Fe 88 B 6 , 41 K for Pr 8 Fe 86 B 6 , 38 K for Pr 10 Fe 8 4 B 6 and T = 34 K for Pr 12 Fe 82 B 6 . The specific absorption rates (SARs) of the powders were 201 Wkg -1 for Pr 6 Fe 88 B 6 composition, 158 Wkg -1 on the composition Pr 8 Fe 86 B 6 , and 114 Wkg -1 for Pr 10 Fe 84 B 6 and Pr 12 Fe 82 B 6 compositions. (author)
Single crystal magnetic, dielectric and thermal studies of the relaxor ferroelectric Pb(Fe2/3W1/3)O3
International Nuclear Information System (INIS)
Ye, Z.G.; Sato, M.; Kita, E.; Bursill, L.A.; Schmid, H.
1998-01-01
The magnetic, dielectric and thermal properties of the complex perovskite Pb(Fe 2/3 W 1/3 )O 3 [PFW] have been studied on single crystals by means of a SQUID magnetometer, dielectric measurements and thermal analysis. Anomalies in the temperature dependence of the magnetization have revealed magnetic phase transitions at T N1 =350 K and T N2 =20 K. These two steps of antiferromagnetic ordering are attributed to the microstructural feature of the complex perovskite, characterized by ordered and disordered arrangements on the B-site, giving rise to a strong superexchange interaction of - Fe 3 + - O - Fe 3+ - type with a higher ordering temperature, and to a weak superexchange interaction of the B-site ordered elpasolite type - Fe 3+ + - O - W - O - Fe 3+ - with a lower Neel temperature. The low temperature antiferromagnetic phase exhibits a weak ferromagnetism. The dielectric properties of PFW show a relaxor ferroelectric behaviour with a dispersive maximum of permittivity at Tm (170 -190 K). The magnetic phase transition at T N2 =20 K results in anomalies both of the real part of permittivity and the dissipation factor, suggesting a magneto-electric coupling via magneto-structural interactions
Thick CoFeB with perpendicular magnetic anisotropy in CoFeB-MgO based magnetic tunnel junction
Directory of Open Access Journals (Sweden)
V. B. Naik
2012-12-01
Full Text Available We have investigated the effect of an ultra-thin Ta insertion in the CoFeB (CoFeB/Ta/CoFeB free layer (FL on magnetic and tunneling magnetoresistance (TMR properties of a CoFeB-MgO system with perpendicular magnetic anisotropy (PMA. It is found that the critical thickness (tc to sustain PMA is doubled (tc = 2.6 nm in Ta-inserted CoFeB FL as compared to single CoFeB layer (tc = 1.3 nm. While the effective magnetic anisotropy is found to increase with Ta insertion, the saturation magnetization showed a slight reduction. As the CoFeB thickness increasing, the thermal stability of Ta inserted structure is significantly increased by a factor of 2.5 for total CoFeB thickness less than 2 nm. We have observed a reasonable value of TMR for a much thicker CoFeB FL (thickness = 2-2.6 nm with Ta insertion, and without significant increment in resistance-area product. Our results reveal that an ultra-thin Ta insertion in CoFeB might pay the way towards developing the high-density memory devices with enhanced thermal stability.
Magnetic and electron spin resonance studies of W doped CoFe2O4 polycrystalline materials
Singamaneni, S. R.; Martinez, L. M.; Swadipta, R.; Ramana, C. V.
2018-05-01
We report the magnetic and electron spin resonance (ESR) properties of W doped CoFe2O4 polycrystalline materials, prepared by standard solid-state reaction method. W was doped (0-15%) in CFO lattice on Fe site. Isothermal magnetization measurements reveal that the coercive field (Hc) (1300-2200 Oe) and saturation magnetization MS (35-82 emu/g) vary strongly as a function of W doping at all the temperatures (4-300 K) measured. We believe that a strong decrease in magnetic anisotropy in CFO after doping with W could cause a decrease in Hc. Up on doping CFO with W in place of Fe, the process transforms part of Fe3+ into Fe2+ due to the creation of more oxygen vacancies. This hinders the super-exchange interaction between Fe3+ and Fe2+, which causes a decrease in MS. Zero-field cooled (ZFC) and field cooled (FC, 1000 Oe) magnetization responses measured at 4 K on 1% W doped CFO show no indication of exchange bias, inferring that there are no other microscopic secondary magnetic phases (no segregation). This observation is corroborated by ESR (9.398 GHz) measurements collected as a function of temperature (10-150 K) and W doping (0-15%). We find that ESR spectra did not change after doping with W above 0.5%. However, ESR spectra collected from 0.5% W doped CFO sample showed a strong temperature dependence. We observed several ESR signals from 0.5% W doped CFO sample that could be due to phase separation.
Magnetic and electron spin resonance studies of W doped CoFe2O4 polycrystalline materials
Directory of Open Access Journals (Sweden)
S. R. Singamaneni
2018-05-01
Full Text Available We report the magnetic and electron spin resonance (ESR properties of W doped CoFe2O4 polycrystalline materials, prepared by standard solid-state reaction method. W was doped (0-15% in CFO lattice on Fe site. Isothermal magnetization measurements reveal that the coercive field (Hc (1300-2200 Oe and saturation magnetization MS (35-82 emu/g vary strongly as a function of W doping at all the temperatures (4-300 K measured. We believe that a strong decrease in magnetic anisotropy in CFO after doping with W could cause a decrease in Hc. Up on doping CFO with W in place of Fe, the process transforms part of Fe3+ into Fe2+ due to the creation of more oxygen vacancies. This hinders the super-exchange interaction between Fe3+ and Fe2+, which causes a decrease in MS. Zero-field cooled (ZFC and field cooled (FC, 1000 Oe magnetization responses measured at 4 K on 1% W doped CFO show no indication of exchange bias, inferring that there are no other microscopic secondary magnetic phases (no segregation. This observation is corroborated by ESR (9.398 GHz measurements collected as a function of temperature (10-150 K and W doping (0-15%. We find that ESR spectra did not change after doping with W above 0.5%. However, ESR spectra collected from 0.5% W doped CFO sample showed a strong temperature dependence. We observed several ESR signals from 0.5% W doped CFO sample that could be due to phase separation.
International Nuclear Information System (INIS)
Fujitsuna, N.; Igarashi, M.; Abe, F.
2000-01-01
The effect of Si on the precipitation behavior of M 23 C 6 and Fe 2 W Laves phase during creep and on the creep deformation behavior was studied on 8.5Cr-2W-VNb steels at 650 C for up to 10000 h. During creep and aging, Fe 2 W Laves phase precipitated and then the amount and the mean particle size of Fe 2 W precipitates became larger with increasing Si concentration, while the amount and the mean size of M 23 C 6 was scarcely changed by the addition of Si. It was cleared that Si-addition influence more strongly on the precipitation of Fe 2 W than M 23 C 6 . The creep rupture strength of the steels increased with increasing Si concentration at high stresses and short rupture times less than 2000 h, while it had a maximum at 0.3% Si and then decreased with increasing Si concentration at low stresses and long rupture times longer than 2000 h. The decrease of creep rate in the acceleration creep region was more significant by Si-addition, and the minimum creep rate was decreased by Si-addition at all stress conditions. The change in creep deformation behavior by Si-addition resulted mainly from the change in precipitation behavior of Fe 2 W, such that the decrease of creep rate in transient creep region is more significant by acceleration of Fe 2 W precipitating on the lath boundary to suppress the recovery of the lath structure and that the extreme increase of creep rate after reaching a minimum creep rate and the decrease of duration of acceleration creep region occurred with coarsening of Fe 2 W. (orig.)
Magnetoresistance in amorphous NdFeB/FeB compositionally modulated multilayers
International Nuclear Information System (INIS)
Peral, G.; Briones, F.; Vicent, J.L.
1991-01-01
Resistance measurements have been done in amorphous Nd 12 Fe 80 B 8 sputtered films and in amorphous sputtered Nd 26 Fe 68 B 6 /Fe 92 B 8 multilayers between 6 and 150 K with applied magnetic field parallel (LMR) and perpendicular (TMR) up to 7 T. The samples were grown by dc triode sputtering, with nominal unequal (2:1) layer thicknesses. The layered character of the samples have been tested by x-ray diffraction. Longitudinal magnetoresistance (LMR) is positive and transverse magnetoresistance (TMR) is negative. The magnetoresistance values are higher than in amorphous ferromagnets, and multilayering of these alloys produces much larger magnetoresistance values than either alloy alone and there is a strong dependence on the multilayer wavelength. The MR shows a weak temperature dependence in the temperature interval that was investigated
Stress impedance effect of FeCoSiB/Cu/FeCoSiB sandwich layers on flexible substrate
International Nuclear Information System (INIS)
Peng, B.; Zhang, W.L.; Liu, J.D.; Zhang, W.X.
2011-01-01
FeCoSiB/Cu/FeCoSiB sandwich layers were deposited on flexible substrate to develop flexible stress/strain sensors. The influence of stress on the impedance of the multilayers is reported. The results show that the variation of the impedance increases with the increase in deflection of the free end of the cantilever. A relative change in impedance of 6.4% is obtained in the FeCoSiB(1.5 μm)/Cu(0.25 μm)/FeCoSiB(1.5 μm) sandwich layers at 1 MHz with deflection of 2 mm. The stress impedance effects are sensitive to the frequency of the current and the thickness of both FeCoSiB and Cu layers. The stress impedance effect increases with the increase in the thickness of FeCoSiB or Cu layers. The stress impedance effect increases slightly with the increase in frequency and decreases with the further increase in frequency, which can be understood by the stress and frequency-dependent permeability of magnetic films. - Research highlights: → We deposited FeCoSiB/Cu/FeCoSiB multilayer on flexible substrate. → We studied the stress impedance effect of FeCoSiB/Cu/FeCoSiB multilayer. → Stress impedance effect increases with thickness of both FeCoSiB and Cu layer.→ Stress impedance effect is dependent on current frequency. → Results are understood using stress and frequency-dependent permeability.
Phase diagrams of the Fe-rich part of the Fe-W system under high pressure
International Nuclear Information System (INIS)
Yamane, T.; Kang, Y.S.; Minamino, Y.; Araki, H.; Hiraki, A.; Miyamoto, Y.
1995-01-01
Phase diagrams of the Fe-rich part of the Fe-W system under high pressure (1.2 and 2.2 GPa) were established by a reaction-diffusion method and calculated with thermodynamic and volumetric data. When high pressure is applied, the γ region extends and the α region contracts. As a result of increasing pressure, eutectoid and peritectoid reactions appear. (orig.)
Microstructure and properties of multiphase sintered cermets Fe-Fe2B
International Nuclear Information System (INIS)
Nowacki, J.; Klimek, L.
1998-01-01
The process of multiphase sintering of iron in the vacuum has been analysed. As a result of the process iron-iron boride cermets have been produced. Fe-Fe 2 B cermets were obtained as a result of sintering of the Fe and B pure elements in the vacuum. Attemps at sintering in the solid phase and with the participation of the liquid phase, the Fe-Fe 2 B eutectic, have been made. Metallographic qualitative and quantitative studies, X-ray structural qualitative and qauantitative analysis allowed to determine the structure of Fe 2 B cermets, as well as a description of the kinetics of quantitative changes in phase proportions in the course of sintering. It has been found that their structure varies widely depending on sintering parameters and the composition of the sinters. Measurements of the Fe-Fe 2 B cermets hardness and measurements on wear during dry friction by the pin-on-disc method have shown distinct advantages of the cermets as a modern constructional materials. The hardness of Fe-Fe 2 B cermets, depending on their chemical composition and sintering parameters, ranges widely from 150 to 1500 HV, and their resistance to wear is comparable to that of diffusively boronized steels. FeFe 2 B cermets are a composite material in which iron boride, Fe 2 B, with a hardness of about 1800 HV plays the role of the reinforcement,while iron-iron boride, Fe-Fe 2 B, with a hardness of about 500 HV plays the role of matrix. The eutectic in the spaces between iron boride grains is composed of boron solid solution plates in iron with a hardness of arround 250 HV, and iron boride, Fe 2 B, plates with a hardness of approximaly 1800 HV. The combination of such different materials, a hard reinforcement and a relatively plastic matrix produces favourable properties of the cermet thus produced high hardness (1500 HV) constant over whole cross section of the material, resistance of abrasive wear and acceptable ductility. The properties mentioned above, resulting from the cermet
Micro-structuring of thick NdFeB films using high-power plasma etching for magnetic MEMS application
International Nuclear Information System (INIS)
Jiang, Yonggang; Fujita, Takayuki; Higuchi, Kohei; Maenaka, Kazusuke; Masaoka, Shingo; Uehara, Minoru
2011-01-01
This paper describes the micro-patterning of thick NdFeB magnetic films using a high-power plasma etching method. The effects of RF bias power and gas composition on the selectivity and etching rate are experimentally studied. A maximum etching rate of 60 nm min −1 is achieved with an inductively coupled plasma power of 500 W and a RF bias power of 200 W. A maximum selectivity of 0.26 between hard baked AZP4903 photoresist and NdFeB magnetic films is achieved when volumetric Cl 2 concentration is 2.5%. NdFeB micro-magnets as thick as 4.2 µm are achieved by using AZP4903 photoresist. Magnetic film as thick as 10 µm can be patterned by using SU-8 photoresist with a thickness of 100 µm as the mask. The magnetic property of patterned microstructures is characterized using a vibrating sample magnetometer and the magnetic field distribution is measured using a Hall effect sensor IC. The characterization results indicate that the patterned magnetic microstructures have a high magnetic remanance of 1.0 T, which is comparable to that of the non-patterned NdFeB films.
Microstructural properties of electrochemically prepared Ni-Fe-W powders
Energy Technology Data Exchange (ETDEWEB)
Ribic-Zelenovic, L. [Faculty of Agronomy, University of Kragujevac, Cacak (Serbia); Cirovic, N. [Joint Laboratory for Advanced Materials of SASA, Technical Faculty Cacak, University of Kragujevac, Cacak (Serbia); Spasojevic, M. [Faculty of Agronomy, University of Kragujevac, Cacak (Serbia); Mitrovic, N., E-mail: nmitrov@tfc.kg.ac.rs [Joint Laboratory for Advanced Materials of SASA, Technical Faculty Cacak, University of Kragujevac, Cacak (Serbia); Maricic, A. [Joint Laboratory for Advanced Materials of SASA, Technical Faculty Cacak, University of Kragujevac, Cacak (Serbia); Pavlovic, V. [Faculty of Agriculture, University of Belgrade, Belgrade (Serbia)
2012-07-16
A nanostructured Ni-Fe-W powder was obtained by electrodeposition from ammonium citrate electrolyte within the current density range of 500-1000 mA cm{sup -2} at the electrolyte temperature of 50 Degree-Sign C-70 Degree-Sign C. XRD analysis shows that the powder contains an amorphous matrix having embedded nanocrystals of the FCC solid solution of iron and tungsten in nickel, with an average crystal grain size of 3.4 nm, a high internal microstrain value and a high density of chaotically distributed dislocations. EDS analysis exhibits that the chemical composition of the Ni-24%Fe-11%W powder does not depend upon current density and electrolyte temperature due to the diffusion control of the process of codeposition of nickel, iron and tungsten. SEM micrographs show that the electrodeposition results in the formation of two particle shapes: large cauliflower-like particles and small dendrite particles. The cauliflower-like particles contain deep cavities at hydrogen evolution sites. Cavity density increases with increasing deposition current density. Smaller powder particles are formed at higher temperatures and at higher current densities. During the first heating, relative magnetic permeability decreases reaching the Curie temperature at about 350 Degree-Sign C and after cooling exhibits a 12% increase due to the performed relaxation process. Following the second heating to 500 Degree-Sign C, the magnetic permeability of the powder is about 5% lower than that of the as-prepared powder due to crystallization of the amorphous phase of the powder and the crystal grain growth in FCC phase. - Highlights: Black-Right-Pointing-Pointer Electrodeposition Ni-Fe-W powder from ammonium citrate electrolyte (500-1000 mA cm{sup -2}). Black-Right-Pointing-Pointer Powder contains amorphous matrix and embedded nanocrystals 3.4 nm. Black-Right-Pointing-Pointer Chemical composition Ni-24%Fe-11%W do not depend upon current density and electrolyte temperature. Black
Energy Technology Data Exchange (ETDEWEB)
Yang, SeungMo; Lee, JaBin; An, GwangGuk [Novel Functional Materials and Devices Lab, The Research Institute for Natural Science, Department of Physics, Hanyang University, Seoul 133-791 (Korea, Republic of); Kim, JaeHong [Division of Nano-Scale Semiconductor Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Chung, WooSeong [Nano Quantum Electronics Lab, Department of Electronics and Computer Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Hong, JinPyo, E-mail: jphong@hanyang.ac.kr [Novel Functional Materials and Devices Lab, The Research Institute for Natural Science, Department of Physics, Hanyang University, Seoul 133-791 (Korea, Republic of); Division of Nano-Scale Semiconductor Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of)
2015-07-31
We describe Ta underlayer thickness influence on thermal stability of perpendicular magnetic anisotropy in Ta/CoFeB/MgO/W stacks. It is believed that thermal stability based on Ta underlay is associated with thermally-activated Ta atom diffusion during annealing. The difference in Ta thickness-dependent diffusion behaviors was confirmed with X-ray photoelectron spectroscopy analysis. Along with a feasible Ta thickness model, our observations suggest that an appropriate seed layer choice is needed for high temperature annealing stability, a critical issue in the memory industry. - Highlights: • We observed changes in the diffusion behavior with regard to Ta seed layer thickness. • It was observed that a thinner Ta seed layer induced more annealing-stable features. • However, ultra-thin (0.75 nm) Ta shows unstable characteristics about the annealing process. • It was possibly due to a rugged interface of the Ta layer by the island growth process.
Solution structure of leptospiral LigA4 Big domain
Energy Technology Data Exchange (ETDEWEB)
Mei, Song; Zhang, Jiahai [Hefei National Laboratory for Physical Sciences at Microscale, School of Life Sciences, University of Science and Technology of China, Hefei, Anhui 230026 (China); Zhang, Xuecheng [School of Life Sciences, Anhui University, Hefei, Anhui 230039 (China); Tu, Xiaoming, E-mail: xmtu@ustc.edu.cn [Hefei National Laboratory for Physical Sciences at Microscale, School of Life Sciences, University of Science and Technology of China, Hefei, Anhui 230026 (China)
2015-11-13
Pathogenic Leptospiraspecies express immunoglobulin-like proteins which serve as adhesins to bind to the extracellular matrices of host cells. Leptospiral immunoglobulin-like protein A (LigA), a surface exposed protein containing tandem repeats of bacterial immunoglobulin-like (Big) domains, has been proved to be involved in the interaction of pathogenic Leptospira with mammalian host. In this study, the solution structure of the fourth Big domain of LigA (LigA4 Big domain) from Leptospira interrogans was solved by nuclear magnetic resonance (NMR). The structure of LigA4 Big domain displays a similar bacterial immunoglobulin-like fold compared with other Big domains, implying some common structural aspects of Big domain family. On the other hand, it displays some structural characteristics significantly different from classic Ig-like domain. Furthermore, Stains-all assay and NMR chemical shift perturbation revealed the Ca{sup 2+} binding property of LigA4 Big domain. - Highlights: • Determining the solution structure of a bacterial immunoglobulin-like domain from a surface protein of Leptospira. • The solution structure shows some structural characteristics significantly different from the classic Ig-like domains. • A potential Ca{sup 2+}-binding site was identified by strains-all and NMR chemical shift perturbation.
Solution structure of leptospiral LigA4 Big domain
International Nuclear Information System (INIS)
Mei, Song; Zhang, Jiahai; Zhang, Xuecheng; Tu, Xiaoming
2015-01-01
Pathogenic Leptospiraspecies express immunoglobulin-like proteins which serve as adhesins to bind to the extracellular matrices of host cells. Leptospiral immunoglobulin-like protein A (LigA), a surface exposed protein containing tandem repeats of bacterial immunoglobulin-like (Big) domains, has been proved to be involved in the interaction of pathogenic Leptospira with mammalian host. In this study, the solution structure of the fourth Big domain of LigA (LigA4 Big domain) from Leptospira interrogans was solved by nuclear magnetic resonance (NMR). The structure of LigA4 Big domain displays a similar bacterial immunoglobulin-like fold compared with other Big domains, implying some common structural aspects of Big domain family. On the other hand, it displays some structural characteristics significantly different from classic Ig-like domain. Furthermore, Stains-all assay and NMR chemical shift perturbation revealed the Ca"2"+ binding property of LigA4 Big domain. - Highlights: • Determining the solution structure of a bacterial immunoglobulin-like domain from a surface protein of Leptospira. • The solution structure shows some structural characteristics significantly different from the classic Ig-like domains. • A potential Ca"2"+-binding site was identified by strains-all and NMR chemical shift perturbation.
Interface interaction in the B4C/(Fe-B-C) system
International Nuclear Information System (INIS)
Aizenshtein, M.; Mizrahi, I.; Froumin, N.; Hayun, S.; Dariel, M.P.; Frage, N.
2008-01-01
The wetting behavior in the B 4 C/(Fe-C-B) system was investigated in order to clarify the role of Fe additions on the sinterability of B 4 C. Iron and its alloys with C and B react with the boron carbide substrate and form a reaction zone consisting of a fine mixture of FeB and graphite. The apparent contact angles are relatively low for the alloys with a moderate concentration of the boron and carbon and allow liquid phase sintering to occur in the B 4 C-Fe mixtures. A dilatometric study of the sintering kinetics confirms that liquid phase sintering actually takes place and leads to improved mass transfer. A thermodynamic analysis of the ternary Fe-B-C system allows accounting for the experimental observations
Study of the Fe-Ti/W system for joining applications in high-temperature fusion reactor components
Energy Technology Data Exchange (ETDEWEB)
Prado, J. de, E-mail: javier.deprado@urjc.es [Rey Juan Carlos University, Calle Tulipán s/n 28933 Móstoles, Madrid (Spain); Sánchez, M. [Rey Juan Carlos University, Calle Tulipán s/n 28933 Móstoles, Madrid (Spain); Alvaredo, P.; Gordo, E. [Carlos III de Madrid University, Avenida de la Universidad 30, 28911 Leganés, Madrid (Spain); Ureña, A. [Rey Juan Carlos University, Calle Tulipán s/n 28933 Móstoles, Madrid (Spain)
2016-10-15
Highlights: • Simulations show good correlation versus experimental results for Fe-Ti/W system. • The joint is predicted to be stable at the service conditions of the component. • The predictions could help to analyze different scenarios during its service life. - Abstract: The interaction of the Fe-Ti/W system in a brazed divertor component of the future fusion power plant has been studied. The reactivity between the substrates and the filler is an important factor to obtain a high quality joint. Thermodynamic and diffusion simulation software can be valuable tools for studying these effects, particularly in scenarios that are difficult to experimentally analyze. Two different strategies have been performed: 1) simulation processes using the Thermo-Calc and DICTRA software to calculate the phase diagram and simulate the diffusion process, respectively, and 2) experimental tests in a furnace to join W-W substrates using a filler with an 86Fe-Ti composition to analyze the operational brazeability and compare it with the simulation results. The simulation processes predicted two of the three phases that formed at the experimental joint (α-Fe and TiC). The interaction at the W-filler interface predicted by DICTRA correlates with the experimental results, where Fe, Ti and C diffused into the W substrate and moved the interface by 25 μm. Simulations also show the stability of the interface over the lifetime of the component. The combined use of Thermo-Calc and DICTRA software enabled the accurate prediction of different scenarios in the system of Fe-Ti-C/W.
Study of the Fe-Ti/W system for joining applications in high-temperature fusion reactor components
International Nuclear Information System (INIS)
Prado, J. de; Sánchez, M.; Alvaredo, P.; Gordo, E.; Ureña, A.
2016-01-01
Highlights: • Simulations show good correlation versus experimental results for Fe-Ti/W system. • The joint is predicted to be stable at the service conditions of the component. • The predictions could help to analyze different scenarios during its service life. - Abstract: The interaction of the Fe-Ti/W system in a brazed divertor component of the future fusion power plant has been studied. The reactivity between the substrates and the filler is an important factor to obtain a high quality joint. Thermodynamic and diffusion simulation software can be valuable tools for studying these effects, particularly in scenarios that are difficult to experimentally analyze. Two different strategies have been performed: 1) simulation processes using the Thermo-Calc and DICTRA software to calculate the phase diagram and simulate the diffusion process, respectively, and 2) experimental tests in a furnace to join W-W substrates using a filler with an 86Fe-Ti composition to analyze the operational brazeability and compare it with the simulation results. The simulation processes predicted two of the three phases that formed at the experimental joint (α-Fe and TiC). The interaction at the W-filler interface predicted by DICTRA correlates with the experimental results, where Fe, Ti and C diffused into the W substrate and moved the interface by 25 μm. Simulations also show the stability of the interface over the lifetime of the component. The combined use of Thermo-Calc and DICTRA software enabled the accurate prediction of different scenarios in the system of Fe-Ti-C/W.
Shape of growing crystals of primary phases in autectic alloys of Fe - Fe2B and Ni - Ni3B systems
International Nuclear Information System (INIS)
Tavadze, F.N.; Garibashvili, V.I.; Nakaidze, Sh.G.
1983-01-01
Shapes of Fe 2 B and Ni 3 B crystal growth in eutectic Fe-B and Ni-B system alloys are considered. Iron hemiboride primary crystals take the form of a plane-face phase boundary and inherit a tetragonal prismatic lattice. After the crystal attains the critical size the dendritic branching occurs resulting in formation of a typical sceleton dendrite. Comparison of data obtained with entropy of melting for Fe 2 B and Ni 3 B borides shows that FeB crystals during the growth should take the spherical form. It is stated that the shape of growing crystals in Fe-Fe 2 B and Ni-Ni 2 B eutectic colonies is determined by the shape of borides
Liga NiCrSiBC: Microestrutura e Dureza de Revestimentos Processados a Arco e a Laser
Directory of Open Access Journals (Sweden)
Leandro J. da Silva
2015-03-01
Full Text Available A técnica de processamento é determinante sobre características de um revestimento. Isso porque o aporte térmico, que depende da técnica e dos parâmetros, tem influência sobre a diluição e a taxa de solidificação. Em ligas com baixa complexidade metalúrgica, o impacto do processamento com técnicas de deposição que impõem maior taxa de resfriamento podem se traduzir em refino da microestrutura. Espera-se que quanto mais refinada a microestrutura maior a resistência mecânica do revestimento. Entretanto, na deposição de ligas de maior complexidade metalúrgica isso nem sempre ocorre, porque a elevada taxa de resfriamento pode suprimir formação/precipitação de fases responsáveis pela resistência. Neste estudo, a influência do processamento sobre microestrutura e dureza de revestimentos da liga Colmonoy-6® foi avaliada. A liga foi processada por plasma com arco transferido (PTA e laser de diodo de alta potência (HPDL sobre chapas de AISI 304 com dois níveis de diluição. Em ambos os casos, revestimentos de boa qualidade e livres defeitos foram obtidos. O aumento do teor de Fe (diluição e as diferentes taxas de resfriamento decorrem do processamento com diferentes parâmetros e técnicas. Em consequência, ocorrem mudanças significativas na microestrutura e na dureza dos revestimentos que estão associadas à distribuição, morfologia e composição química dos carbonetos e, principalmente, dos boretos.
Directory of Open Access Journals (Sweden)
C. Lago Peñas
2010-09-01
Full Text Available
RESUMEN
Los objetivos de este trabajo son dos. En primer lugar estudiar los efectos que tiene disputar un partido de la Liga de Campeones sobre el resultado alcanzado por los equipos en la Liga Española en esa misma semana. En segundo lugar, verificar si la probabilidad de ganar frente a perder en la Liga Española es mayor o no para los equipos con experiencia en la Liga de Campeones frente a aquellos otros conjuntos que disputan por primera vez esta competición. La muestra consiste en 184 partidos de la Liga Española de Fútbol jugados por los equipos que se encontraban simultáneamente disputando la primera fase de la Liga de Campeones en las temporadas 2003-2004, 2004-2005 y 2005-2006. Los datos utilizados en la investigación han sido tomados de la página oficial de la Liga de Campeones, de la Liga Española y suministrados por GECA SPORT.
De acuerdo con los resultados de la estimación de un modelo logit multinomial, disputar un partido de la Liga de Campeones durante la semana de competición no reduce la probabilidad de los equipos de ganar frente a perder en el partido de la Liga Nacional. Incluso tiene un efecto positivo para los equipos debutantes en la competición europea: cuando juegan durante la semana tienen más probabilidades de ganar en la Liga Nacional (p<0,01.
Palabras clave: resultado, fútbol, Liga de Campeones. logit multinomial, Liga Española
ABSTRACT
This paper has two goals. First, studying the impact of playing in the Champions League on the results in the Spanish League. Second, analyzing whether being a beginner team in the
A physical interpretation of the jet-like X-ray emission from supernova remnant W49B
International Nuclear Information System (INIS)
Miceli, M.; Miceli, M.; Decourchelle, A.; Ballet, J.; Miceli, M.; Bocchino, F.; Hughes, J.; Hwang, U.; Hwang, U.; Petre, R.
2008-01-01
In the framework of the study of supernova remnants and their complex interaction with the interstellar medium and the circumstellar material, we focus on the galactic supernova remnant W49B. Its morphology exhibits an X-ray bright elongated nebula, terminated on its eastern end by a sharp perpendicular structure aligned with the radio shell. The X-ray spectrum of W49B is characterized by strong K emission lines from Si, S, Ar, Ca, and Fe. There is a variation of the temperature in the remnant with the highest temperature found in the eastern side and the lowest one in the western side. The analysis of the recent observations of W49B indicates that the remnant may be the result of an asymmetric bipolar explosion where the ejecta are collimated along a jet-like structure and the eastern jet is hotter and more Fe-rich than the western one. Another possible scenario associates the X-ray emission with a spherical explosion where parts of the ejecta are interacting with a dense belt of ambient material. To overcome this ambiguity we present new results of the analysis of an XMM-Newton observation and we perform estimates of the mass and energy of the remnant. We conclude that the scenario of an anisotropic jet-like explosion explains quite naturally our observation results, but the association of W49B with a hyper-nova and a gamma-ray burst, although still possible, is not directly supported by any evidence. (authors)
Effects of Fe fine powders doping on hot deformed NdFeB magnets
International Nuclear Information System (INIS)
Lin, Min; Wang, Huijie; Zheng, Jingwu; Yan, Aru
2015-01-01
The composite NdFeB magnets with blending melt-spun flakes and Fe fine powders were prepared by the hot-pressed and hot-deformed route. Characterizations of the hot-deformed NdFeB magnets affected by the doped Fe powders were tested. The doped Fe powders decrease the hot-deformed pressure when the strain is between 15 and 50%. XRD patterns show that the doped Fe powders have little influence on the c-axis alignment of hot-deformed NdFeB magnets in the press direction. The B r and the (BH) max get improved when the doped Fe powders are less than 3 wt%. The doped Fe of hot-deformed NdFeB magnets exists in the elongated state and the spherical state surrounded by the Nd-rich phase. With the Fe fraction increasing, the potential of magnet moves to the positive direction and the diameter of the Nyquist arc becomes larger, which indicate that the corrosion resistance improved effectively. The bending strength was enhanced by the elongated α-Fe phase embedded in the matrix 2:14:1 phase. - Highlights: • The doped Fe powders have little influence on the c-axis alignment of magnets. • The elongated Fe powders are more than the spherical Fe powders in the magnets. • The corrosion resistance is improved effectively with the increasing Fe fraction. • The bending strength is enhanced by the elongated α-Fe phase embedded in the matrix
Effects of Fe fine powders doping on hot deformed NdFeB magnets
Energy Technology Data Exchange (ETDEWEB)
Lin, Min, E-mail: linm@nimte.ac.cn [Ningbo Institute of Material Technology & Engineering Chinese Academy of Science, Ningbo 315201 (China); Wang, Huijie [Ningbo Jinji Strong Magnetic Material Company, Ningbo 315041 (China); Zheng, Jingwu [Zhejiang University of Technology, Hangzhou 310014 (China); Yan, Aru [Ningbo Institute of Material Technology & Engineering Chinese Academy of Science, Ningbo 315201 (China)
2015-04-01
The composite NdFeB magnets with blending melt-spun flakes and Fe fine powders were prepared by the hot-pressed and hot-deformed route. Characterizations of the hot-deformed NdFeB magnets affected by the doped Fe powders were tested. The doped Fe powders decrease the hot-deformed pressure when the strain is between 15 and 50%. XRD patterns show that the doped Fe powders have little influence on the c-axis alignment of hot-deformed NdFeB magnets in the press direction. The B{sub r} and the (BH){sub max} get improved when the doped Fe powders are less than 3 wt%. The doped Fe of hot-deformed NdFeB magnets exists in the elongated state and the spherical state surrounded by the Nd-rich phase. With the Fe fraction increasing, the potential of magnet moves to the positive direction and the diameter of the Nyquist arc becomes larger, which indicate that the corrosion resistance improved effectively. The bending strength was enhanced by the elongated α-Fe phase embedded in the matrix 2:14:1 phase. - Highlights: • The doped Fe powders have little influence on the c-axis alignment of magnets. • The elongated Fe powders are more than the spherical Fe powders in the magnets. • The corrosion resistance is improved effectively with the increasing Fe fraction. • The bending strength is enhanced by the elongated α-Fe phase embedded in the matrix.
Matsunaga, James; Medeiros, Marco A; Sanchez, Yolanda; Werneid, Kristian F; Ko, Albert I
2007-10-01
The life cycle of the pathogen Leptospira interrogans involves stages outside and inside the host. Entry of L. interrogans from moist environments into the host is likely to be accompanied by the induction of genes encoding virulence determinants and the concomitant repression of genes encoding products required for survival outside of the host. The expression of the adhesin LigA, the haemolysin Sph2 (Lk73.5) and the outer-membrane lipoprotein LipL36 of pathogenic Leptospira species have been reported to be regulated by mammalian host signals. A previous study demonstrated that raising the osmolarity of the leptospiral growth medium to physiological levels encountered in the host by addition of various salts enhanced the levels of cell-associated LigA and LigB and extracellular LigA. In this study, we systematically examined the effects of osmotic upshift with ionic and non-ionic solutes on expression of the known mammalian host-regulated leptospiral genes. The levels of cell-associated LigA, LigB and Sph2 increased at physiological osmolarity, whereas LipL36 levels decreased, corresponding to changes in specific transcript levels. These changes in expression occurred irrespective of whether sodium chloride or sucrose was used as the solute. The increase of cellular LigA, LigB and Sph2 protein levels occurred within hours of adding sodium chloride. Extracellular Sph2 levels increased when either sodium chloride or sucrose was added to achieve physiological osmolarity. In contrast, enhanced levels of extracellular LigA were observed only with an increase in ionic strength. These results indicate that the mechanisms for release of LigA and Sph2 differ during host infection. Thus, osmolarity not only affects leptospiral gene expression by affecting transcript levels of putative virulence determinants but also affects the release of such proteins into the surroundings.
A safety-based comparison of pure LigaSure use and LigaSure-tie technique in total thyroidectomy.
Pergel, A; Yucel, A Fikret; Aydin, I; Sahin, D A; Aras, S; Kulacoglu, H
2014-01-01
Sutureless total thyroidectomy by using vessel sealing devices has been shown to be safe in some recent clinical studies. However, some surgeons are still concerned about the use of these energy devices in the vicinity of there current laryngeal nerve and parathyroid glands. The objective of this study was to investigate the effects of the use of pure LigaSure on postoperative complications and to discuss the pertinent literature. A total of 456 patients having undergone a total thyroidectomy operation between June 2009 and March 2011 were included in the study. Data were prospectively collected and retrospectively evaluated. Patients were separated into 2 groups. Group L comprised of 182 patients where onlyLigaSure was used, and group LT consisted of 274 patients where ligation was used in the vicinity of the recurrent laryngeal nerve and parathyroid glands, and LigaSure was used in all other parts of the surgery. Patient's blood calcium values were checked preoperatively and at postoperative 24, 48, and 72 hours. Groups were assessed in terms of demographic properties, thyroid pathology, duration of operation, and postoperative complications. Groups were similar in respect of demographic properties, operation duration, thyroid gland pathology. No mortality rate was recorded. Laboratory hypocalcemia rate was higher in group L (P 0.003), but no significant difference was identified between groups in terms of symptomatic hypocalcemia.No permanent hypocalcemia or recurrent laryngeal nerve injury developed in any of the patients in the two groups. Pure LigaSure for total thyroidectomy may increase laboratory hypocalcemia rate, but not symptomatic hypocalcemia. Hemorrhage related complications were similar and low in the two groups. Ligations in the places close to delicate anatomic structures did not cause longer operative times and may be a safer option in total thyroidectomy. Celsius.
Effect of Fe-Mn addition on microstructure and magnetic properties of NdFeB magnetic powders
Kurniawan, C.; Purba, A. S.; Setiadi, E. A.; Simbolon, S.; Warman, A.; Sebayang, P.
2018-03-01
In this paper, the effect of Fe-Mn alloy addition on microstructures and magnetic properties of NdFeB magnetic powders was investigated. Varied Fe-Mn compositions of 1, 5, and 10 wt% were mixed with commercial NdFeB type MQA powders for 15 minutes using shaker mill. The characterizations were performed by powder density, PSA, XRD, SEM, and VSM. The Fe-Mn addition increased the powder density of NdFeB/Fe-Mn powders. On the other side, particle size distribution slightly decreased as the Fe-Mn composition increases. Magnetic properties of NdFeB/Fe-Mn powders changed with the increasing of Fe-Mn content. SEM analysis showed the particle size of NdFeB/Fe-Mn powder was smaller as the Fe-Mn composition increases. It showed that NdFeB/Fe-Mn particles have different size and shape for NdFeB and Fe-Mn particles separately. The optimum magnetic properties of NdFeB/Fe-Mn powder was achieved on the 5 wt% Fe-Mn composition with remanence M r = 49.45 emu/g, coercivity H c = 2.201 kOe, and energy product, BH max = 2.15 MGOe.
Balance Competitivo en las Ligas Europeas de Baloncesto y la NBA
Directory of Open Access Journals (Sweden)
Jorge García - Unanue
2014-01-01
Full Text Available Las ligas deportivas dependen del equilibrio competitivo entre los equipos para ser atractivas para los espectadores, de ahí la aparición del balance competitivo. Por ello, las distintas ligas deportivas han adquirido diferentes formatos que determinarán su competitividad. El objetivo de este artículo es comparar el balance competitivo de la NBA y las principales ligas europeas, teniendo en cuenta la NBA en su conjunto y cada una de sus conferencias de forma independiente. Las variables utilizadas para medir el balance competitivo han sido el índice Hirschman-Herfindal y las ratios C5 y C8. Los resultados muestran un mejor balance competitivo de la NBA en conjunto respecto a las ligas europeas, sin embargo estas diferencias desaparecen al analizar las conferencias de forma independiente. Se concluye que al tener en cuenta cada una de las conferencias de forma independiente, con una estructura más similar a las ligas europeas, se presenta un balance competitivo parecido bajo los indicadores utilizados. Sin embargo, la NBA incluye limitaciones en la competición que siguen favoreciendo la posibilidad de que sea más atractiva para el espectador.
Tao, B. S.
2014-09-08
Magnetic properties of Co40Fe40B20(CoFeB) thin films sandwiched between Ta and MgAl2O4layers have been systematically studied. For as-grown state, Ta/CoFeB/MgAl2O4structures exhibit good perpendicular magnetic anisotropy (PMA) with interface anisotropy Ki=1.22erg/cm2, which further increases to 1.30erg/cm2after annealing, while MgAl2O4/CoFeB/Ta multilayer shows in-plane magnetic anisotropy and must be annealed in order to achieve PMA. For bottom CoFeB layer, the thickness window for PMA is from 0.6 to 1.0nm, while that for top CoFeB layer is between 0.8 and 1.4nm. Perpendicular magnetic tunnel junctions (p-MTJs) with a core structure of CoFeB/MgAl2O4/CoFeB have also been fabricated and tunneling magnetoresistance ratio of about 36% at room temperature and 63% at low temperature have been obtained. The intrinsic excitations in the p-MTJs have been identified by inelastic electron-tunneling spectroscopy.
Tao, B. S.; Li, D. L.; Yuan, Z. H.; Liu, H. F.; Ali, S. S.; Feng, J. F.; Wei, H. X.; Han, X. F.; Liu, Y.; Zhao, Y. G.; Zhang, Q.; Guo, Zaibing; Zhang, Xixiang
2014-01-01
Magnetic properties of Co40Fe40B20(CoFeB) thin films sandwiched between Ta and MgAl2O4layers have been systematically studied. For as-grown state, Ta/CoFeB/MgAl2O4structures exhibit good perpendicular magnetic anisotropy (PMA) with interface anisotropy Ki=1.22erg/cm2, which further increases to 1.30erg/cm2after annealing, while MgAl2O4/CoFeB/Ta multilayer shows in-plane magnetic anisotropy and must be annealed in order to achieve PMA. For bottom CoFeB layer, the thickness window for PMA is from 0.6 to 1.0nm, while that for top CoFeB layer is between 0.8 and 1.4nm. Perpendicular magnetic tunnel junctions (p-MTJs) with a core structure of CoFeB/MgAl2O4/CoFeB have also been fabricated and tunneling magnetoresistance ratio of about 36% at room temperature and 63% at low temperature have been obtained. The intrinsic excitations in the p-MTJs have been identified by inelastic electron-tunneling spectroscopy.
Crystallization of amorphous pseudobinary alloys of the type (Fe1-x Nix)80 B20
International Nuclear Information System (INIS)
Vasconcellos, M.A.Z.; Baibich, M.N.
1984-01-01
It was studied the crystallization of amorphous metallic ribbons of Fe 1-x Ni x 80 B 2 0 using the method of isochronous heating at variable slopes. The crystallization temperatures were determined from the transition observed in the electrical resistivity. (M.W.O.) [pt
Interface interaction in the B{sub 4}C/(Fe-B-C) system
Energy Technology Data Exchange (ETDEWEB)
Aizenshtein, M. [Department of Material Engineering, Ben-Gurion University, P.O. Box 653, Beer-Sheva 84105 (Israel); NRC-Negev, P.O. Box 9001, Beer-Sheva 84190 (Israel); Mizrahi, I.; Froumin, N.; Hayun, S.; Dariel, M.P. [Department of Material Engineering, Ben-Gurion University, P.O. Box 653, Beer-Sheva 84105 (Israel); Frage, N. [Department of Material Engineering, Ben-Gurion University, P.O. Box 653, Beer-Sheva 84105 (Israel)], E-mail: nfrage@bgu.ac.il
2008-11-15
The wetting behavior in the B{sub 4}C/(Fe-C-B) system was investigated in order to clarify the role of Fe additions on the sinterability of B{sub 4}C. Iron and its alloys with C and B react with the boron carbide substrate and form a reaction zone consisting of a fine mixture of FeB and graphite. The apparent contact angles are relatively low for the alloys with a moderate concentration of the boron and carbon and allow liquid phase sintering to occur in the B{sub 4}C-Fe mixtures. A dilatometric study of the sintering kinetics confirms that liquid phase sintering actually takes place and leads to improved mass transfer. A thermodynamic analysis of the ternary Fe-B-C system allows accounting for the experimental observations.
Transient field for W ions traversing Fe hosts and for Os ions traversing Fe and Ni hosts
International Nuclear Information System (INIS)
Stuchbery, A.E.; Bolotin, H.H.; Doran, C.E.
1987-02-01
Transient field strengths were measured for 184 W and 186 W ions traversing thin, magnetized Fe foils with velocities in the range 1.8 ≤ v/v>=o ≤ 5.7 (v>=o Bohr velocity) and for 188 Os, 190 Os, 192 Os ions traversing polarized Ni hosts with average velocities =o> ∼ 4. The present measured transient field strengths, together with previously measured results for W, Os ions, are compared with transient-field strength parametrizations, and discussed in terms of microscopic models of the transient field
LiGA Research and Service at CAMD
International Nuclear Information System (INIS)
Goettert, Jost; Datta, Proyag; Desta, Yohannes; Jin, Yoonyoung; Ling Zhonggeng; Singh, Varshni
2006-01-01
Since 1995 CAMD has been offering exposure services, so called print shop for a variety of users interested in making precision High-Aspect-Ratio Microstructures (HARMST) for various application. Services have been expanded beyond only the print shop service in recent years and now include x-ray mask fabrication, substrate preparation for PMMA and SU- 8 resists, electroplating, finishing and molding. Metallic and polymeric parts are now routinely fabricated for precision engineering, micro-fluidic and micro-optic applications. This paper presents a brief overview of the actual status of LiGA services provided at CAMD including ongoing research efforts and examples of LiGA components for different applications
Temperature compensation of NdFeB permanent magnets
International Nuclear Information System (INIS)
Kim, S.H.; Doose, C.
1997-01-01
Permanent magnet blocks of NdFeB have a relatively high maximum energy product. Because of its relatively low Curie temperature, however, NdFeB has a large temperature coefficient for its residual induction. The temperature coefficients of the relative magnetic fields (ΔB/B)/ΔT in the air gap of NdFeB dipole magnets were reduced from -1.1 x 10 -3 /c to less than 2 x 10 -5 /degree C under operating temperatures of ± 6 C. This was achieved passively by using 1.25-mm-thick strips of 30%-Ni-Fe alloy as flux shunts for the NdFeB blocks. The magnets with soft-steel poles and flux-return yokes were assembled and measured in a temperature-controlled environment
Mechanochemical synthesis of nanocrystalline Fe and Fe–B magnetic alloys
International Nuclear Information System (INIS)
Mohammadi, Majid; Ghasemi, Ali; Tavoosi, Majid
2016-01-01
Mechanochemical synthesis and magnetic characterization of nanocrystalline Fe and Fe–B magnetic alloys was the goal of this study. In this regard, different Fe_2O_3–B_2O_3 powder mixtures with sufficient amount of CaH_2 were milled in a planetary ball mill in order to produce nanocrystalline Fe, Fe_9_5B_5 and Fe_8_5B_1_5 alloys. The produced samples were characterized using X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). The results showed that, nanocrystalline Fe, Fe_9_5B_5 and Fe_8_5B_1_5 alloys can be successfully synthesized by the reduction reaction of Fe_2O_3 and B_2O_3 with CaH_2 during mechanical alloying. The structure of produced Fe_9_5B_5 and Fe_8_5B_1_5 alloys was a combination of Fe and Fe_2B phases with average crystallite sizes of about 15 and 10 nm, respectively. The produced nanocrystalline alloys exhibited soft magnetic properties with the coercivity and saturation of magnetization in the range of 170–240 Oe and 9–28 emu/g, respectively. Increasing the boron content has a destructive effect on soft magnetic properties of Fe–B alloys. - Highlights: • We study the mechanochemical synthesis of nanocrystalline boron, Fe and Fe–B alloys. • We study the reduction reaction of B_2O_3–CaH_2 during milling. • We study the reduction reaction of Fe_2O_3–CaH_2 during milling. • We study the reduction reaction of Fe_2O_3–B_2O_3–CaH_2 during milling. • We study the effect of B on magnetic properties of nanocrystalline Fe–B alloys.
Directory of Open Access Journals (Sweden)
José Evando Aguiar Beserra Júnior
2007-10-01
Full Text Available Foram avaliadas 20 linhagens de melancia, provenientes do cruzamento da cultivar comercial suscetível Crimson Sweet e da introdução PI 595201 resistente ao Watermelon mosaic virus (WMV e Papaya ringspot virus (PRSV-W. As linhagens, e os parentais foram inoculados com o WMV ou com o PRSV-W em casa-de-vegetação distintas. Aos 35 e 49 dias após a primeira inoculação (DAI, as plantas foram avaliadas por meio de uma escala de notas, em que 1 (ausência de sintomas a 5 (intenso mosaico e deformações foliares. Pelos resultados infere-se que, aos 35 DAI, as linhagens 1, 2 e 20 apresentaram resistência tanto para o WMV como para o PRSV-W, com médias de 1,95, 1,80 e 2,25 para o WMV, e de 2,50, 2,30 e 2,50 para o PRSV-W, respectivamente. As linhagens 5, 7 e 13 foram resistentes somente ao WMV e as plantas das linhagens 3, 10 e 18 para o PRSV-W. A reação das linhagens permaneceu em geral pouco alterada aos 49 DAI. A existência de linhagens resistentes somente ao WMV e somente ao PRSV-W, ao lado de linhagens resistentes a ambos os vírus, é indicativo de que as resistências ao WMV e ao PRSV-W não são controladas pelos mesmos genes.Twenty advanced watermelon breeding lines, derived from the cross between cv. Crimson Sweet (susceptible and PI 595201 (resistant to WMV and PRSV-W, were screened for resistance to both potyviruses. The twenty lines, among with Crimson Sweet and PI 595201, were inoculated with either WMV or PRSV-W, in two different greenhouse trials. Plants were evaluated for symptoms 35 and 49 days after the first inoculation (DAI, using a scale from 1 (no symptoms to 5 (severe mosaic and foliar distortion. Evaluations at 35 DAI indicated that lines 1, 2 and 20 had good levels of resistance to both WMV and PRSV-W, with ratings of 1,95, 1,80 and 2,25 for WMV, and of 2,50, 2,30 and 2,50 for PRSV-W, respectively. Lines 5, 7 and 13 were resistant to WMV only, whereas lines 3, 10 and 18 were resistant to PRSV-W only. The reaction of
Mechanochemical synthesis of nanocrystalline Fe and Fe–B magnetic alloys
Energy Technology Data Exchange (ETDEWEB)
Mohammadi, Majid; Ghasemi, Ali, E-mail: ali13912001@yahoo.com; Tavoosi, Majid
2016-12-01
Mechanochemical synthesis and magnetic characterization of nanocrystalline Fe and Fe–B magnetic alloys was the goal of this study. In this regard, different Fe{sub 2}O{sub 3}–B{sub 2}O{sub 3} powder mixtures with sufficient amount of CaH{sub 2} were milled in a planetary ball mill in order to produce nanocrystalline Fe, Fe{sub 95}B{sub 5} and Fe{sub 85}B{sub 15} alloys. The produced samples were characterized using X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). The results showed that, nanocrystalline Fe, Fe{sub 95}B{sub 5} and Fe{sub 85}B{sub 15} alloys can be successfully synthesized by the reduction reaction of Fe{sub 2}O{sub 3} and B{sub 2}O{sub 3} with CaH{sub 2} during mechanical alloying. The structure of produced Fe{sub 95}B{sub 5} and Fe{sub 85}B{sub 15} alloys was a combination of Fe and Fe{sub 2}B phases with average crystallite sizes of about 15 and 10 nm, respectively. The produced nanocrystalline alloys exhibited soft magnetic properties with the coercivity and saturation of magnetization in the range of 170–240 Oe and 9–28 emu/g, respectively. Increasing the boron content has a destructive effect on soft magnetic properties of Fe–B alloys. - Highlights: • We study the mechanochemical synthesis of nanocrystalline boron, Fe and Fe–B alloys. • We study the reduction reaction of B{sub 2}O{sub 3}–CaH{sub 2} during milling. • We study the reduction reaction of Fe{sub 2}O{sub 3}–CaH{sub 2} during milling. • We study the reduction reaction of Fe{sub 2}O{sub 3}–B{sub 2}O{sub 3}–CaH{sub 2} during milling. • We study the effect of B on magnetic properties of nanocrystalline Fe–B alloys.
Tuning high frequency magnetic properties and damping of FeGa, FeGaN and FeGaB thin films
Directory of Open Access Journals (Sweden)
Derang Cao
2017-11-01
Full Text Available A series of FeGa, FeGaN and FeGaB films with varied oblique angles were deposited by sputtering method on silicon substrates, respectively. The microstructure, soft magnetism, microwave properties, and damping factor for the films were investigated. The FeGa films showed a poor high frequency magnetic property due to the large stress itself. The grain size of FeGa films was reduced by the additional N element, while the structure of FeGa films was changed from the polycrystalline to amorphous phase by the involved B element. As a result, N content can effectively improve the magnetic softness of FeGa film, but their high frequency magnetic properties were still poor both when the N2/Ar flow rate ratio is 2% and 5% during the deposition. The additional B content significantly led to the excellent magnetic softness and the self-biased ferromagnetic resonance frequency of 1.83 GHz for FeGaB film. The dampings of FeGa films were adjusted by the additional N and B contents from 0.218 to 0.139 and 0.023, respectively. The combination of these properties for FeGa films are helpful for the development of magnetostrictive microwave devices.
Creep rupture properties of laves phase strengthened Fe--Ta--Cr--W and Fe--Ta--Cr--W--Mo alloys
International Nuclear Information System (INIS)
Singh, S.
1975-12-01
A small addition of tungsten (0.5 at. percent) was shown to have an effect similar to that of molybdenum on the phase transformation characteristics of alloy Ta7Cr (with a nominal composition of 1 at. percent Ta, 7 at. percent Cr, balance Fe). The existence of time-temperature dependent transformation behavior in alloy Ta7Cr0.5W was confirmed. The effect of spheroidization time and temperature on creep strength was determined. In addition, effect of mechanical processing prior to aging, on creep strength was also determined. It was also shown that by suitable modifications of composition, the grain boundary film can be broken during the aging treatment without the use of spheroidization treatment. Microhardness, tensile and creep properties have been determined. Optical metallography and scanning electron microscopy have been used to follow the microstructural changes and mode of fracture. The creep rupture strength of alloy Ta7CrW alloy was found to be superior to many of the best commercially available ferritic alloys at 1200 0 F. (21 fig., 8 tables)
Kannan, R.; Devaki, P.; Premkumar, P. S.; Selvambikai, M.
2018-04-01
Electrodeposition of nanocrystalline NiFe and NiFeW thin films were carried out from ammonium citrate bath at a constant current density and controlled pH of 8 by varying the bath temperature from 40 °C to 70 °C. The surface morphology and chemical composition of the electrodeposited NiFe and NiFeW soft magnetic thin films were studied by using SEM and EDAX. The SEM micrographs of the films coated at higher electrodeposited bath temperature have no micro cracks and also the films have more uniform surface morphology. The existence of crystalline nature of the coated films were analysed by XRD. The presence of predominant peaks in x-ray diffraction pattern (compared with JCPDS data) reveal that the average crystalline size was in the order of few tens of nano meters. The magnetic properties such as coercivity, saturation magnetization and magnetic flux density have been calculated from vibrating sample magnetometer analysis. The VSM result shows that the NiFeW thin film synthesised at 70 °C exhibit the lower coercivity with higher saturation magnetization. The hardness and adhesion of the electroplated films have been investigated. Reasons for variation in magnetic properties and structural characteristics are also discussed. The electroplated NiFe and NiFeW thin films can be used for Micro Electro Mechanical System (MEMS) applications due to their excellent soft magnetic behaviour.
SOJA IAC/IAS-5: CULTIVAR RESISTENTE AO CANCRO DA HASTE
Directory of Open Access Journals (Sweden)
MASCARENHAS HIPÓLITO ASSUNÇÃO ANTONIO
1998-01-01
Full Text Available Há aproximadamente oito anos, o cancro da haste (Phomopsis phaseoli f. sp. meridionalis/Diaporthe phaseolorum f. sp. meridionalis da soja tem sido o principal fator limitante da produtividade em áreas de manifestação da doença. O seu controle mediante cultivares resistentes é o método mais econômico. Num ensaio em casa de vegetação, visando avaliar o efeito de doses de potássio no controle do cancro da haste, no cultivar IAS-5, moderadamente resistente, verificou-se haver plantas altamente resistentes, comprovadas em três gerações, todas inoculadas com o fungo causador da doença. A importância da obtenção do IAS-5 e de sua multiplicação deve-se a ser o mais cultivado no Estado de São Paulo e apresentar resistência ao cancro da haste.
Properties of ternary NiFeW alloy coating by jet electrodeposition
Indian Academy of Sciences (India)
In this paper, ternary NiFeW alloy coatings were prepared by jet electrodeposition, and the effects of lord salt concentration, jet speed, current density and temperature on the properties of the coatings, including the composition, microhardness, surface morphology, structure and corrosion resistance, were investigated.
Ocorrência de fungos filamentosos termo-resistentes em polpa de tomate envasada assepticamente
Directory of Open Access Journals (Sweden)
BAGLIONI Flávio
1999-01-01
Full Text Available Este trabalho teve como objetivo principal determinar a ocorrência de fungos filamentosos termo-resistentes durante o processamento asséptico de polpa de tomate (8° BRIX. Durante o período de safra de tomate foram feitas amostragens em 9 lotes (3 no início, 3 no pico e 3 em fim de safra e no período de entresafra em 5 lotes. Foi feita a enumeração de fungos termo-resistentes nas amostras coletadas durante as diferentes etapas do processo asséptico de cada lote. Foram obtidas contagens médias relativamente baixas, variando entre <1 e 8UFC/100mL de amostra. As maiores contagens foram obtidas na matéria prima e na água de pré lavagem e transporte. Cinqüenta linhagens de fungos termo-resistentes detectadas no procedimento de enumeração foram isoladas, codificadas e estocadas. Os esporos de cada isolado com 1 mês de cultivo foram submetidos a diferentes choques térmicos para selecionar a linhagem de fungo mais termo-resistente. O isolado de fungo mais termo-resistente (sobrevivência ao choque à 100° C/25 minutos foi identificado como Neosartorya fischeri.
Directory of Open Access Journals (Sweden)
Chun-Chieh Yeh
2015-01-01
Full Text Available Safety of either LigaSure or rubber band in closing inflamed appendiceal stump in acute appendicitis has been less investigated. In this study, cecal ligation followed by resecting inflamed cecum was performed to mimic appendectomy in a rat model of acute appendicitis. Rats were sacrificed immediately (Group A and 7 days (Group B after cecal resection, respectively. The cecal stumps were closed by silk ligature (S, 5 mm LigaSure (L, or rubber band (R. Seven days after cecal resection, the LigaSure (BL and silk subgroups (BS had significantly less intra-abdominal adhesion and better laparotomy wound healing than rubber band subgroup (BR. The initial bursting pressure at cecal stump was comparable among the three methods; along with tissue healing process, both BL and BS provided a higher bursting pressure than BR 7 days after appendectomy. BL subgroup had more abundant hydroxyproline deposition than BS and BR subgroup. Furthermore, serum TNF-α in BR group kept persistently increasing along with time after cecal resection. Thus, the finding that LigaSure but not rubber band is safe in sealing off the inflamed cecal stump in rat model of acute appendicitis suggests the possibility of applying LigaSure for appendectomy via single port procedure or natural orifice transluminal endoscopic surgery (NOTES.
Mechanically alloyed PrFeB nanocrystalline magnets
International Nuclear Information System (INIS)
Kaszuwara, W.; Leonowicz, M.
1998-01-01
Mechanically alloyed PrFeB nanocrystalline magnets were prepared by extensive ball milling of Pr, Fe and Fe 80 B 20 powders, followed by diffusion annealing. After milling, the material consisted of nanocrystalline α-Fe crystallites embedded in amorphous Pr-rich matrix. Thermomagnetic and calorimetric investigations of the transformations which occurred during annealing showed that the amorphous phase crystallised at 240 C, leading to the formation of crystalline Pr having lattice constants 10% greater than those shown in the ASTM data. This fact indicated that mechanical alloying and low temperature annealing led to the formation of a solid solution of either Fe or B in Pr, which does not exist in the equilibrium state. The Pr 2 Fe 14 B phase was subsequently formed within a temperature range of 420-620 C. The magnetic properties of magnets depend on the phase structure and grain size. Milling time appears to be a decisive processing parameter for the tailoring of the magnetic properties. Depending on the phase structure, the coercivities varied from 100 to 1200 kA/m and, respectively, the remanences from 0.98 T to 0.6 T. The highest maximum energy product was 80 kJ/m 3 . (orig.)
Magnetic properties of ball-milled TbFe2 and TbFe2B
Indian Academy of Sciences (India)
Unknown
1. Introduction. The RFe2 (R = rare earth) Laves phase compounds are known to possess large cubic anisotropy (Clark et al 1972) and highest Curie temperature (TC) of all RT2 compounds. (T = transition metal). RFe2 ... TbFe2 and TbFe2B were prepared by arc melting the high pure elements (Tb and B, 99⋅9% purity; Fe, ...
MAGNETIC VISCOSITY IN NdFeB MAGNETS
Martinez , J.; Missell , F.
1988-01-01
The relaxation of the magnetization is calculated for isotropic and anisotropic magnets. For NdFeB magnets, the dependence of Sv on texture, above room temperature, is roughly consistent with the model, while the NdDyFeB magnets show no dependence upon texture.
Supernova remnant W49B and its environment
Energy Technology Data Exchange (ETDEWEB)
Zhu, H.; Tian, W. W.; Zuo, P., E-mail: zhuhui@bao.ac.cn, E-mail: tww@bao.ac.cn [Key Laboratory of Optical Astronomy, National Astronomical Observatories, Chinese Academy of Sciences, Beijing 100012 (China)
2014-10-01
We study gamma-ray supernova remnant (SNR) W49B and its environment using recent radio and infrared data. Spitzer Infrared Spectrograph low resolution data of W49B shows shocked excitation lines of H{sub 2} (0,0) S(0)-S(7) from the SNR-molecular cloud interaction. The H{sub 2} gas is composed of two components with temperatures of ∼260 K and ∼1060 K, respectively. Various spectral lines from atomic and ionic particles are detected toward W49B. We suggest that the ionic phase has an electron density of ∼500 cm{sup –3} and a temperature of ∼10{sup 4} K by the spectral line diagnoses. The mid- and far-infrared data from MSX, Spitzer, and Herschel reveal a 151 ± 20 K hot dust component with a mass of 7.5 ± 6.6 × 10{sup –4} M {sub ☉} and a 45 ± 4 K warm dust component with a mass of 6.4 ± 3.2 M {sub ☉}. The hot dust is likely from materials swept up by the shock of W49B. The warm dust may possibly originate from the evaporation of clouds interacting with W49B. We build the H I absorption spectra of W49B and four nearby H II regions (W49A, G42.90+0.58, G42.43-0.26, and G43.19-0.53) and study the relation between W49B and the surrounding molecular clouds by employing the 2.12 μm infrared and CO data. We therefore obtain a kinematic distance of ∼10 kpc for W49B and suggest that the remnant is likely associated with the CO cloud at about 40 km s{sup –1}.
Plasma sprayed Nd-Fe-B permanent magnets
International Nuclear Information System (INIS)
Willson, M.; Bauser, S.; Liu, S.; Huang, M.
2003-01-01
This study demonstrated that the plasma spray deposition method is an alternative process for producing Nd-Fe-B magnets in addition to the two existing principal processes: the powder metallurgy process for producing sintered Nd-Fe-B magnets and the melt spinning process for bonded Nd-Fe-B magnets. Plasma spray is a potentially better process for producing magnetic parts with complicated shape, large area, thin thickness, small dimension, or unusual geometry. High intrinsic coercivity greater than 15 kOe was readily obtained for Nd 16 Dy 1 Fe 76 B 7 even in the as-deposited condition when the substrate was preheated. The plasma spray process contains only three steps: melting, crushing, and plasma spray, which is much simpler than the powder metallurgy and melt spinning processes. Without preheating the substrate, the coercivity was usually very low (∼0.1 kOe) in the as-deposited condition and it increased to 10 to >15 kOe after anneal. Evidence of magnetocrystalline anisotropy was observed in plasma sprayed Nd 15 Dy 1 Fe 77 B 7 magnets when the substrate was not preheated. It is believed that a crystal texture was developed during the plasma spray as a result of the existence of a temperature gradient in the solidifying melt
New developments in NdFeB-based permanent magnets
International Nuclear Information System (INIS)
Liu, Z.W.
2011-01-01
NdFeB based alloys have been used as permanent magnets for almost thirty years. The recent researches aim at optimizing the composition, microstructure and properties, reducing cost, and developing new processes. The demand for sintered magnet is increasing. Efforts are directed towards improving properties by controlling grain boundary diffusion, minimizing the rare earth (RE) content and also improving production yield. As for bonded magnets, to enhance remanence and energy product, nanocrystalline powders are employed. High thermal stability has been realized by mixing NdFeB with hard ferrite powders. For nanocrystalline and nano composite NdFeB based alloys, both compositional modification and microstructural optimization have been carried out. New approaches have also been proposed to prepare NdFeB magnets with idea structure. Surfactant assisted ball milling is a good top-down method to obtain nano sized hard magnetic particles and anisotropic nano flakes. Synthesis of NdFeB nanoparticles and NdFeB/Fe (Co) nano composite powders by bottom-up techniques, such as chemical reduction process and co-precipitation, has been successful very recently. To assemble nanocrystalline NdFeB powders or nanoparticles into bulk magnets, various novel consolidation processes including spark plasma sintering and high velocity press have been employed. Hot deformation can be selected as the process to achieve anisotropy in nanocrystalline magnets. (author)
Substrate matters: Magnetic tuning of the Fe monolayer
Energy Technology Data Exchange (ETDEWEB)
Ramanathan, A.A.; Khalifeh, J.M.
2017-03-15
The effect of substrate on the magnetism of the Fe monolayer (ML) is investigated using the total energy DFT calculations with the local spin density approximation (LSDA). The results show an in plane ferromagnetic coupling (FM) and a magnetic moment of 1.78 µ{sub B} for the relaxed Fe ML in the presence of the vanadium substrate. In comparison, the surface Fe(001) magnetic moment ranges between 2.97–3.01 µ{sub B}. This difference in the Fe surface moment of more than 1 µ{sub B} in the presence or absence of Vanadium allows tuning of the Fe magnetic moment and has great potential as a magnetic switch and in spintronic devices. The surface magnetic quenching of Fe with V is much more pronounced than with other transition metal substrates like Molybdenum or Tungsten. We have a reduction of 40.5% of the Fe (001) surface moment which is more than double the reduction obtained with the Fe/Mo(001) or the Fe/W(001) systems. The magnetic quenching is due to the strong hybridization between the Fe and V d bands. This is supported by the observed charge density redistribution and large inward relaxation of 18.37% for the Fe surface upon structural relaxation. The Fe ML is antiferromagnetically (AF) coupled with the V interfacial layer, which has an appreciable induced magnetic moment of 0.48 µ{sub B}. - Highlights: • We report the magnetic quenching of a Fe ML on V(001) substrate. • Almost double as compared to Mo and W substrates. • The Fe surface ML on V(001) shows FM ordering as opposed to AF ordering for Fe ML on Mo(001) and W(001) substrates.
Computer-aided topological analysis of Nd-Fe-B ternary system
International Nuclear Information System (INIS)
Liu, G.; Xu, P.; Zhang, W.
1993-01-01
A three-dimensional partially matrixed topological model of the Nd-Fe-B ternary phase diagram has been established based on experimental results assessed comprehensively with the aid of a computer-aided design and graphic and graphics software, AutoCAD (R10), and application programs developed in this work. Vertical sections at 5.88 at.% B, Nd:B = 1:1, Fe-Nd/sub 2/Fe/sub 14/B-Nd, Nd/sub 2/Fe/sub 17/-Nd/sub 2/Fe/sub 7/B/sub 6/ have been cut out from the model and the corresponding phase relationships have been analyzed. Among them, those on the Nd-rich protons of both the sections at 5.88 at.% B and Nd:B = 2:1 and those on the Nd/sub 2/Fe/sub 14/B-Nd section are given for the first time. (author)
Corroded microstructure of HDDR-NdFeB magnetic powders
International Nuclear Information System (INIS)
Zhu, L.Y.; Itakura, M.; Tomokiyo, Y.; Kuwano, N.; Machida, K.
2004-01-01
The microstructure of corroded HDDR-NdFeB magnetic powders in bonded magnet has been investigated by transmission electron microscopy. Following an exposure time of 300 h at 398 K in air, the HDDR-NdFeB magnetic powders are found covered with an altered layer about 300 nm thick on the surface. The layer is composed of α-Fe grains 5-10 nm in diameter and h-Nd 2 O 3 grains smaller than 5 nm. Under the altered layer, corrosion has proceeded along the Nd 2 (Fe,Co) 14 B grain boundaries to leave a wetting layer composed of a dense mixture of α-Fe and h-Nd 2 O 3 phase. The appearance of α-Fe grains in both of the altered layer wetting layer leads to the high magnetic flux loss of the corroded HDDR-NdFeB bonded magnet
Estudo de ligas de ouro por XRF e SEM-EDS
Coxito, Afonso Maria Teixeira
2016-01-01
Serve o presente estudo para testar uma metodologia para análise de ligas metálicas, em particular ligas de ouro, utilizando as técnicas de fluorescência de raios-X e microscopia electrónica de varrimento. No contexto do presente estudo, foi identificada a composição das folhas de ouro utilizadas em obras de arte. As técnicas laboratoriais utilizadas foram: Microscopia óptica; Espectroscopia de fluorescência de raios-X com dispersão de energia (EDXRF); Microscopi...
Systematic measurements of transient fields for W, Os and Pt ions traversing Fe
International Nuclear Information System (INIS)
Stuchbery, A.E.; Heseltine, T.H.; Anderssen, S.S.; Bolotin, H.H.; Byrne, A.P.; Fabricius, B.; Kibedi, T.
1994-01-01
Transient magnetic fields were measured for W, Os and Pt ions traversing iron hosts with average velocities in the range from approximately 1.6 v 0 to 4.8 v 0 (v 0 = c/137, Bohr velocity). Transient fields for W and Os in Fe are consistent with behaviour found for lighter rare-earth ions and are about 20% stronger than those for Pt in Fe over the majority of the velocity range examined. A measurement was made to confirm that possible heavy-ion beam induced attenuations of the transient field are negligible for low-velocity Pt ions excited by Ni beams. Results are discussed in terms of both empirical and model-based parameterizations of the transient field strength. (orig.)
Ion-beam mixing and tribology of Fe/B multilayers
International Nuclear Information System (INIS)
Hu, R.; Rehn, L.E.; Baldo, P.M.; Fenske, G.R.
1990-01-01
This paper reports the interdiffusion of Fe and B trilayer specimens during 1-MeV Kr + bombardment studied using Rutherford backscattering and electron microscopy. The square of the interdiffusion distance during mixing at 300 degrees C was found to depend linearly on the irradiation dose. Arrhenius behavior with an apparent activation enthalpy of 0.7 eV was observed for the mixing between 200 and 500 degrees C. Electron microscopy of ion-beam mixed multilayer specimens revealed that two crystalline compounds, Fe 2 B and Fe 3 B, formed during bombardment at 450 degrees C, while two different amorphous Fe/B phases formed at 300 degrees C. Substantially improved adhesion and reduced friction were observed for Fe/B multilayers ion-beam mixed onto M50 steel substrates at 450 degrees C
International Nuclear Information System (INIS)
Constantinescu, C.; Patroi, E.; Codescu, M.; Dinescu, M.
2013-01-01
Highlights: ► NdFeB thin films grown by PLD, in vacuum and in nitrogen, are presented. ► Nitrogen inclusion in thin film structures is related to improved coercitivity. ► Magnetical, optical and morphological properties of the thin films are discussed. - Abstract: NdFeB is a very attractive material for applications in electrical engineering and in electronics, for high-tech devices where high coercive field and high remanence are needed. In this paper we demonstrate that the deposition of nitrogen doped NdFeB thin films by pulsed laser deposition, in the presence of a nitrogen radiofrequency plasma beam, exhibit improved magnetic properties and surface morphology, when compared to vacuum deposited NdFeB layers. A Nd:YAG pulsed laser (3ω and 4ω) was focused on a NdFeB target, in vacuum, or in the presence of a nitrogen plasma beam. Substrate temperature (RT-850 °C), nitrogen gas pressure, and radiofrequency power (75–150 W), were particularly varied. The thin films were investigated by means of X-ray diffraction, atomic force microscopy, scanning electron microscopy, spectroscopic-ellipsometry, and vibrating sample magnetometry.
Energy Technology Data Exchange (ETDEWEB)
Constantinescu, C., E-mail: catalin.constantinescu@inflpr.ro [National Institute for Laser, Plasma and Radiation Physics, 409 Atomistilor bd., Magurele, RO-077125, Bucharest (Romania); Patroi, E.; Codescu, M. [National Institute for Research and Development in Electrical Engineering - Advanced Research, 313 Spl. Unirii, Sector 3, RO-030138, Bucharest (Romania); Dinescu, M. [National Institute for Laser, Plasma and Radiation Physics, 409 Atomistilor bd., Magurele, RO-077125, Bucharest (Romania)
2013-03-01
Highlights: Black-Right-Pointing-Pointer NdFeB thin films grown by PLD, in vacuum and in nitrogen, are presented. Black-Right-Pointing-Pointer Nitrogen inclusion in thin film structures is related to improved coercitivity. Black-Right-Pointing-Pointer Magnetical, optical and morphological properties of the thin films are discussed. - Abstract: NdFeB is a very attractive material for applications in electrical engineering and in electronics, for high-tech devices where high coercive field and high remanence are needed. In this paper we demonstrate that the deposition of nitrogen doped NdFeB thin films by pulsed laser deposition, in the presence of a nitrogen radiofrequency plasma beam, exhibit improved magnetic properties and surface morphology, when compared to vacuum deposited NdFeB layers. A Nd:YAG pulsed laser (3{omega} and 4{omega}) was focused on a NdFeB target, in vacuum, or in the presence of a nitrogen plasma beam. Substrate temperature (RT-850 Degree-Sign C), nitrogen gas pressure, and radiofrequency power (75-150 W), were particularly varied. The thin films were investigated by means of X-ray diffraction, atomic force microscopy, scanning electron microscopy, spectroscopic-ellipsometry, and vibrating sample magnetometry.
Eindrapportage onderzoek naar ontwikkeling Verticillium resistente Acer
Hiemstra, J.A.; Sluis, van der B.J.
2013-01-01
Dit project is de laatste fase in het onderzoek naar de ontwikkeling van Verticillium-resistente Acer platanoides (Noorse esdoorn) onderstammen wat in 1993 van start ging op het toenmalige CPRO-DLO (nu PRI) met grootschalige selectie-experimenten. PPO-Bomen heeft vanaf 1999 onderzoek gedaan naar
Energy Technology Data Exchange (ETDEWEB)
Kelly, James J. (Sandia National Laboratories, Livermore, CA); Goods, Steven Howard (Sandia National Laboratories, Livermore, CA)
2005-06-01
The report presented below is to appear in ''Electrochemistry at the Nanoscale'', Patrik Schmuki, Ed. Springer-Verlag, (ca. 2005). The history of the LIGA process, used for fabricating dimensional precise structures for microsystem applications, is briefly reviewed, as are the basic elements of the technology. The principal focus however, is on the unique aspects of the electrochemistry of LIGA through-mask metal deposition and the generation of the fine and uniform microstructures necessary to ensure proper functionality of LIGA components. We draw from both previously published work by external researchers in the field as well as from published and unpublished studies from within Sandia.
Microstructure and wear properties of laser cladding Ti-Al-Fe-B coatings on AA2024 aluminum alloy
International Nuclear Information System (INIS)
Xu Jiang; Liu Wenjin; Kan Yide; Zhong Minlin
2006-01-01
In order to improve wear resistance of aluminum alloy, the in situ synthesized TiB 2 and Ti 3 B 4 peritectic composite particulate reinforced metal matrix composite formed on the 2024 aluminum alloy by laser cladding with a powder mixture of Fe coated Boron, Ti and Al was successfully achieved using 3 kW CW CO 2 laser. The laser cladding coating present excellent bonding with aluminum alloy substrate. The chemical composition, microstructure and phase structure of the composite clad coating were analyzed by energy dispersive X-ray spectroscopy (EDX), SEM and XRD. The typical microstructure of composite coating is composed of TiB 2 , Ti 3 B 4 , Al 3 Ti, Al 3 Fe and α-Al. The surface hardness of cladding coating is increased with the amount of added Fe coated B and Ti powder which determines the amount of TiB 2 and Ti 3 B 4 peritectic composite particulate, and obviously higher than that of substrate. The wear tests were carried out using a FALEX-6 type pin-on-disc machine. The test results show that the composite coatings with the in situ synthesized TiB 2 and Ti 3 B 4 peritectic improve wear resistance when compared with the as-received Al substrate
General tests for t→W+b couplings at hadron colliders
International Nuclear Information System (INIS)
Nelson, C.A.; Kress, B.T.; Lopes, M.; McCauley, T.P.
1997-01-01
The modularity property of the helicity formalism is used to provide amplitude expressions and stage-two spin-correlation functions which can easily be used in direct experimental searches for electroweak symmetries and dynamics in the decay processes t→W + b and bar t→W - bar b. The formalism is used to describe the decay sequences t→W + b→(l + ν)b and t→W + b→(j bar d j u )b. Helicity amplitudes for t→W + b are obtained for the most general J bar bt current. Thereby, the most general Lorentz-invariant decay density matrix for t→W + b→(l + ν)b or for t→W + b→(j bar d j u )b is expressed in terms of eight helicity parameters and, equivalently, in terms of the structures of the J bar bt current. The parameters are physically defined in terms of partial-width intensities for polarized final states in t→W + b decay. The full angular distribution for the reactions q bar q and gg→t bar t→(W + b)(W - bar b)→ hor-ellipsis can be used to measure these parameters. Since this adds on spin-correlation information from the next stage of decays in the decay sequence, such an energy-angular distribution is called a stage-two spin-correlation function. copyright 1997 The American Physical Society
Structural investigation of Fe(Cu)ZrB amorphous alloy
International Nuclear Information System (INIS)
Duhaj, P.; Janickovic, D.
1996-01-01
The crystallization process in Fe 86 (Cu 1 )Zr 7 B 6 and Fe 87 Zr 7 B 6 is investigated using the methods of transmission electron microscopy, electron and X-ray diffraction and resistometry. Two crystallization reactions take place during thermal annealing of amorphous Fe 86 (Cu 1 )Zr 7 B 6 and Fe 87 Zr 7 B 6 alloys. In both alloys the first crystallization begins with the formation of nanocrystalline α-Fe at temperature to approximately 800 K. The second crystallization starts above 1000 K; the nanocrystalline phase dissolves and together with the remaining amorphous matrix form rough grains of α-Fe and dispersed Fe 23 Zr 6 phases. From Moessbauer spectroscopy it seems that there exist two neighbourhoods of Fe atoms in the amorphous structure. One of them is characterized by low Zr content and is responsible for the high-field component of the hyperfine field distribution p(H). The second one is rich in Zr and B and is responsible for the low-field component of p(H). This is in accord with the observation of two crystallization steps separated by a large interval of temperatures due to the existence of two chemically different regions or clusters. (orig.)
Environmental degradation of NdFeB magnets
Energy Technology Data Exchange (ETDEWEB)
Yan Gaolin [Wuhan University, School of Physics and Technology, Wuhan 430072 (China)], E-mail: gaolinyan@whu.edu.cn; McGuiness, P.J. [Jozef Stefan Institute (Slovenia); Farr, J.P.G.; Harris, I.R. [School of Metallurgy and Materials, University of Birmingham, Elms Road, Edgbaston, Birmingham B15 2TT (United Kingdom)
2009-06-10
A mechanism for pitting of NdFeB magnet because of differential-aeration beneath a water droplet is proposed and observations of the localised corrosions are presented. NdFeB magnets exhibit general corrosion along the grain boundaries when etched in Viella's reagent. However, localised corrosion of these magnets results in a crater-like feature when corrosion is produced in an environmental chamber, e.g. when Nd{sub 16}Fe{sub 76}B{sub 8} magnets are corroded in the environmental chamber at 85 deg. C, relative humidity (RH): 80%. This is attributed to the condensation of water droplets on the surface of samples and the concentration gradient of oxygen dissolved in the droplets then influencing the corrosion process. It is thought that during the process of pitting, the high concentration of H{sup +} in the center of the pit accelerates the pit development; meanwhile, the cathodic Nd{sub 2}Fe{sub 14}B matrix phase absorbs the nascent hydrogen atoms. It is believed that pits start at the Nd-rich phase and then propagate along the grain boundaries.
Certain structural properties of the phase-binder of the alloys in W-Ni-Fe system
International Nuclear Information System (INIS)
Minakova, R.V.; Storchak, N.A.; Verkhovodov, P.A.; Bazhenova, L.G.; Poltoratskaya, V.L.
1980-01-01
The paper is concerned with effect of cooling conditions and subsequent heat treatment on grain size, lattice parameter and distribution of composing elements in the phase-binder of the W-Ni-Fe-alloy. The X-ray diffraction analysis was used to determine that the phase-binder structure depends on the heat treatment after liquid-phase sintering and consists of coarse grains with a diameter 3-8 mm for the annealed W-Ni-Fe-alloy decreasing to 40-100 μm at slow cooling. The determined change in solubility and of grain interface enrichment with tungsten in the phase-binder
Investigating Early and Late Complications in Conventional and LigaSure Hemorroidectomy
Directory of Open Access Journals (Sweden)
M Zare
2014-06-01
Full Text Available Introduction: The traditional Milligan-Morgan and the Ferguson operations are still the most used for patients with symptomatic haemorrhoids of III and IV degrees. Nowadays LigaSure is used as a new technique to decrease the complications resulting from conventional hemorroidectomy. In this study, patients were investigated on the basis of the following main outcomes: mean operative time, postoperative pain (score and duration, bleeding loss in operation, early (within the first month after surgery and late (after the first month complications in conventional as well as LigaSure hemorroidectomy. Methods: it is an analytical study conducted on 101 patients aged 19–80 years old of both males and females with III and IV-degree hemorrhoids who had been gone to Shahid Sadoughi hospital between 2011 and 2012. Forty-three patients were treated by conventional diathermy and fifty -eight by LigaSure. Patients received analgesic administration for about 24 hours after operations and, after hospital discharge. In fact, analgesia was administered until 5 days (three times a day. All patients were required to record pain from the first postoperative day until the 28th postoperative day on a self-administered NAS scale (0–10. Results: Patients completed a questionnaire face to face one week, one month, six, and twelve months after the operation. The mean operative time, bleeding loss in operation and return to work were significantly shorter in LS group, whereas there were no difference in hospital stay period, anal stenosis, healing time of wound and retention of urinary. A statistically significant difference in pain score was observed three and four days after the operation. Finally, patients with LigaSure haemorrhoidectomy recovered from pain earlier than those with conventional diathermy. Conclusions: although LigaSure proposes additional costs, it is an effective instrument in order to treat hemorrhoids of III and IV degrees.
Magnetization reversal in textured NdFeB-Fe composites observed by domain imaging
Energy Technology Data Exchange (ETDEWEB)
Thielsch, Juliane, E-mail: j.thielsch@ifw-dresden.d [IFW Dresden, Institute for Metallic Materials, P.O. Box 27 01 16, D-01171 Dresden (Germany); Hinz, Dietrich; Schultz, Ludwig; Gutfleisch, Oliver [IFW Dresden, Institute for Metallic Materials, P.O. Box 27 01 16, D-01171 Dresden (Germany)
2010-10-15
Textured composite samples consisting of Nd{sub 13.6}Fe{sub 73.6}Ga{sub 0.6}Co{sub 6.6}B{sub 5.6} (MQU-F{sup TM}) and micron-sized Fe particles with weight ratios from 100:0 to 70:30 have been prepared by hot deformation. Microstructure studies revealed a layered structure of both phases with the layer normal parallel to the pressing direction. Magnetic measurements showed single-phase hysteresis curves for all samples when measured along the pressing direction, which is also the easy axis of magnetization. Coercivity decreased drastically from 1.32 T for pure NdFeB samples to 0.154 T for a sample with 30 wt% Fe. Magneto-optical Kerr microscopy with a digitally enhanced imaging technique has been used to examine the evolution of magnetic domains in the hard and soft phase during demagnetizing a sample consisting of 70 wt% NdFeB and 30 wt% Fe. It is shown that demagnetization takes place via domain rearrangements within the soft phase, which lead to and support the nucleation of reversed interaction domains at phase boundaries. Also nucleation of interaction domains within the hard magnetic phase could be revealed.
Magnetization reversal in textured NdFeB-Fe composites observed by domain imaging
International Nuclear Information System (INIS)
Thielsch, Juliane; Hinz, Dietrich; Schultz, Ludwig; Gutfleisch, Oliver
2010-01-01
Textured composite samples consisting of Nd 13.6 Fe 73.6 Ga 0.6 Co 6.6 B 5.6 (MQU-F TM ) and micron-sized Fe particles with weight ratios from 100:0 to 70:30 have been prepared by hot deformation. Microstructure studies revealed a layered structure of both phases with the layer normal parallel to the pressing direction. Magnetic measurements showed single-phase hysteresis curves for all samples when measured along the pressing direction, which is also the easy axis of magnetization. Coercivity decreased drastically from 1.32 T for pure NdFeB samples to 0.154 T for a sample with 30 wt% Fe. Magneto-optical Kerr microscopy with a digitally enhanced imaging technique has been used to examine the evolution of magnetic domains in the hard and soft phase during demagnetizing a sample consisting of 70 wt% NdFeB and 30 wt% Fe. It is shown that demagnetization takes place via domain rearrangements within the soft phase, which lead to and support the nucleation of reversed interaction domains at phase boundaries. Also nucleation of interaction domains within the hard magnetic phase could be revealed.
Energy Technology Data Exchange (ETDEWEB)
Xia, Junbo [Key Laboratory of Functional Materials and Devices under Special Environments, CAS, Xinjiang Key Laboratory of Electronic Information Materials and Devices, Xinjiang Technical Institute of Physics and Chemistry, CAS, Urumqi 830011 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Zhao, Qing, E-mail: zhaoq@ms.xjb.ac.cn [Key Laboratory of Functional Materials and Devices under Special Environments, CAS, Xinjiang Key Laboratory of Electronic Information Materials and Devices, Xinjiang Technical Institute of Physics and Chemistry, CAS, Urumqi 830011 (China); Gao, Bo [Key Laboratory of Functional Materials and Devices under Special Environments, CAS, Xinjiang Key Laboratory of Electronic Information Materials and Devices, Xinjiang Technical Institute of Physics and Chemistry, CAS, Urumqi 830011 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Chang, Aimin, E-mail: changam@ms.xjb.ac.cn [Key Laboratory of Functional Materials and Devices under Special Environments, CAS, Xinjiang Key Laboratory of Electronic Information Materials and Devices, Xinjiang Technical Institute of Physics and Chemistry, CAS, Urumqi 830011 (China); Zhang, Bo; Ma, Renjun [Key Laboratory of Functional Materials and Devices under Special Environments, CAS, Xinjiang Key Laboratory of Electronic Information Materials and Devices, Xinjiang Technical Institute of Physics and Chemistry, CAS, Urumqi 830011 (China); University of Chinese Academy of Sciences, Beijing 100049 (China)
2014-04-05
Highlights: • The NTC thermister nano-powders Mn{sub 1.05−y}Co{sub 1.95−x−z−w}Ni{sub x}Mg{sub y}Al{sub z}Fe{sub w}O{sub 4} were prepared by microemulsion method. • The metal ions were subsided after twice sediment reaction. • The specimens show good electrical properties by doping some nontransition metals. -- Abstract: The NTC thermistor nano-powders of Mn{sub 1.05−y}Co{sub 1.95−x−z−w}Ni{sub x}Mg{sub y}Al{sub z}Fe{sub w}O{sub 4} were prepared by microemulsion method. Scanning electron microscope (SEM) image showed that the particles were well distributed. The mean particle-size was 72 nm. The structure of the precursor was investigated with Fourier infrared spectrometer (FI). The compositions of the powder and the as-sintered ceramic were evaluated by Energy Disperse Spectroscopy (EDS). X-ray diffraction (XRD) result indicated that the sintered samples were in the spinel structure. The room temperature resistivity ρ{sub 25}, material constant B{sub 25/85} and activation energies of the NTC thermistor are in the range of 1173–19,059 Ω cm, 3169–3771 k, 0.2672–0.3136 eV. The room temperature resistivity and B{sub 25/85} constant were found to increase with Al{sub 2}O{sub 3} content. The Mn{sub 0.9}Co{sub 1.2}Ni{sub 0.21}Mg{sub 0.15}Al{sub 0.09}Fe{sub 0.45}(A2) and Mn{sub 0.9}Co{sub 1.2}Ni{sub 0.27}Mg{sub 0.15}Al{sub 0.03}Fe{sub 0.45}(A3) specimens both showed a 200 °C resistance drift (ΔR/R) within 10% after aging at 910 °C for 600 h.
Structural investigation of Fe(Cu)ZrB amorphous alloy
Energy Technology Data Exchange (ETDEWEB)
Duhaj, P. [Slovenska Akademia Vied, Bratislava (Slovakia). Fyzikalny Ustav; Matko, I. [Slovenska Akademia Vied, Bratislava (Slovakia). Fyzikalny Ustav; Svec, P. [Slovenska Akademia Vied, Bratislava (Slovakia). Fyzikalny Ustav; Sitek, J. [Department of Nuclear Physics and Technology, Slovak Technical University, 81219 Bratislava (Slovakia); Janickovic, D. [Slovenska Akademia Vied, Bratislava (Slovakia). Fyzikalny Ustav
1996-07-01
The crystallization process in Fe{sub 86}(Cu{sub 1})Zr{sub 7}B{sub 6} and Fe{sub 87}Zr{sub 7}B{sub 6} is investigated using the methods of transmission electron microscopy, electron and X-ray diffraction and resistometry. Two crystallization reactions take place during thermal annealing of amorphous Fe{sub 86}(Cu{sub 1})Zr{sub 7}B{sub 6} and Fe{sub 87}Zr{sub 7}B{sub 6} alloys. In both alloys the first crystallization begins with the formation of nanocrystalline {alpha}-Fe at temperature to approximately 800 K. The second crystallization starts above 1000 K; the nanocrystalline phase dissolves and together with the remaining amorphous matrix form rough grains of {alpha}-Fe and dispersed Fe{sub 23}Zr{sub 6} phases. From Moessbauer spectroscopy it seems that there exist two neighbourhoods of Fe atoms in the amorphous structure. One of them is characterized by low Zr content and is responsible for the high-field component of the hyperfine field distribution p(H). The second one is rich in Zr and B and is responsible for the low-field component of p(H). This is in accord with the observation of two crystallization steps separated by a large interval of temperatures due to the existence of two chemically different regions or clusters. (orig.)
Institute of Scientific and Technical Information of China (English)
无
2006-01-01
@@ NdFeB is a permanent magnetic material with excellent performances. It is widely used in electronics and communications. Around 30% of rare earth elements (among which 90% is Nd, others are Tb and Dy) and 2-3% of Co element are contained in the material. NdFeB plays an important role in the development of our society and our economy.
Texturing for bulk α-Fe/Nd2Fe14B nanocomposites with enhanced magnetic properties
International Nuclear Information System (INIS)
Lou, L.; Hou, F.C.; Wang, Y.N.; Cheng, Y.; Li, H.L.; Li, W.; Guo, D.F.; Li, X.H.; Zhang, X.Y.
2014-01-01
In the present study, the texturing of bulk α-Fe/Nd 2 Fe 14 B nanocomposites produced from Nd-lean amorphous Nd x Fe 92.5−x Cu 1.5 B 6 (x=9 to 11.5 at%) via a hot deformation under a uniaxial stress of ∼350 MPa at 973 K has been studied. An enhanced (00l) texture of the hard phase is observed with increasing Nd content, which results in an increase in the magnetic anisotropy of the nanocomposite magnets. As a result, both the coercivity and the remanence of the magnets increase simultaneously with increasing Nd content from x=9–11.5 at%, yielding a significant enhancement of the maximum energy product from (BH) max =13.2 to 17.5 MGOe in the direction parallel to stress axis. - Highlights: • Textured bulk α-Fe/Nd 2 Fe 14 B nanocomposites have been produced from Nd-lean alloys. • Nd content has an effect on the texturing of α-Fe/Nd 2 Fe 14 B nanocomposite magnets. • An enhanced (00l) texture of hard phase is observed with increasing Nd content. • Both the coercivity and remanence increase simultaneously with Nd content
Energy Technology Data Exchange (ETDEWEB)
Hannemann, U.
2004-07-01
In this thesis with pulsed laser deposition Nd-Fe-B layers were deposited. The Nd-Fe-B layers were deposited both on chromium and on tantalum buffers. The layers, which were deposed on tantalum buffers, showed a strong dependence of the nicrostructure and the magnetic properties on the deposition temperature. On layers which were deposited at deposition temperatures around 630 C on the tantalum buffer, the epitactical growth of Nd{sub 2}Fe{sub 14}B could be observed. Summarizingly these layers can be described as micrometer-large and parallely oriented single crystals.
Structural and Moessbauer Effect Studies of 0.5Bi0.95Dy0.05FeO3-0.5Pb(Fe2/3W1/3)O3 Multiferroic
International Nuclear Information System (INIS)
Stoch, A.; Zachariasz, P.; Stoch, P.; Kulawik, J.; Maurin, J.
2011-01-01
A polycrystalline ceramic of 0.5Bi 0.95 Dy 0.05 FeO 3 -0.5Pb(Fe 2/3 W 1/3 )O 3 was synthesized from a solid-state reaction method. At room temperature material exhibits both magnetic and electric dipolar properties simultaneously. Detailed X-ray diffraction analysis and Moessbauer effect studies have been done to determine the crystallographic structure and magnetic properties of 0.5Bi 0.95 Dy 0.05 FeO 3 -0.5Pb(Fe 2/3 W 1/3 )O 3 . T N temperature was estimated at around 600 K. (authors)
Liu, Yue-Lin; Yu, Yang; Dai, Zhen-Hong
2015-01-01
Using first-principles calculations, we investigate the stabilities of He and Hen-vacancy (HenV) clusters in α-Fe and W. Vacancy formation energies are 2.08 eV in α-Fe and 3.11 eV in W, respectively. Single He in both α-Fe and W prefers to occupy the tetrahedral interstitial site. We recalculated the He solution energy considering the effect of zero-point energy (ZPE). The ZPEs of He in α-Fe and W at the tetrahedral (octahedral) interstitial site are 0.072 eV (0.031 eV) and 0.078 eV (0.034 eV), respectively. The trapping energies of single He at vacancy in α-Fe and W are -2.39 eV and -4.55 eV, respectively. By sequentially adding He into vacancy, a monovacancy trap up to 10 He atoms distributing in the vacancy vicinity. Based on the above results combined with statistical model, we evaluate the concentrations of all relevant HenV clusters as a function of He chemical potential. The critical HenV concentration is found to be ∼10-40 (atomic) at the critical temperature T = 600 K in α-Fe and T = 1600 K in W, respectively. Beyond the critical HenV concentrations, considerable HenV aggregate to form HenVm clusters. By further growing of HenVm, the HenVm clusters grow bigger resulting in the larger He bubble formation.
Energy Technology Data Exchange (ETDEWEB)
Benabderrahmane, C., E-mail: chamseddine.benabderrahmane@synchrotron-soleil.fr [Synchrotron SOLEIL, St Aubin (France); Berteaud, P.; Valleau, M.; Kitegi, C.; Tavakoli, K.; Bechu, N.; Mary, A.; Filhol, J.M.; Couprie, M.E. [Synchrotron SOLEIL, St Aubin (France)
2012-03-21
Cryogenic permanent magnet undulators take benefit from improved magnetic properties of RE{sub 2}Fe{sub 14}B (Rare Earth based magnets) at cryogenic temperatures for achieving short period high magnetic field. In particular, using Praseodymium instead of Neodymium generally employed for insertion devices avoids limitation due to Spin Reorientation Transition phenomenon. Magnetic properties of magnet samples (Nd{sub 2}Fe{sub 14}B and Pr{sub 2}Fe{sub 14}B) versus temperature have been investigated and applied to a 20 mm period Nd{sub 2}Fe{sub 14}B (BH50) and to a 18 mm period Pr{sub 2}Fe{sub 14}B (CR53) systems. Four period undulators have been built, characterised and compared to the models.
Microstructure and wear properties of laser cladding Ti-Al-Fe-B coatings on AA2024 aluminum alloy
Energy Technology Data Exchange (ETDEWEB)
Xu Jiang [Laser Processing Research Center, Mechanical Engineering Department, Tsinghua University, Beijing 10084 (China)]. E-mail: xujiang73@sina.com.cn; Liu Wenjin [Laser Processing Research Center, Mechanical Engineering Department, Tsinghua University, Beijing 10084 (China); Kan Yide [Laser Processing Research Center, Mechanical Engineering Department, Tsinghua University, Beijing 10084 (China); Zhong Minlin [Laser Processing Research Center, Mechanical Engineering Department, Tsinghua University, Beijing 10084 (China)
2006-07-01
In order to improve wear resistance of aluminum alloy, the in situ synthesized TiB{sub 2} and Ti{sub 3}B{sub 4} peritectic composite particulate reinforced metal matrix composite formed on the 2024 aluminum alloy by laser cladding with a powder mixture of Fe coated Boron, Ti and Al was successfully achieved using 3 kW CW CO{sub 2} laser. The laser cladding coating present excellent bonding with aluminum alloy substrate. The chemical composition, microstructure and phase structure of the composite clad coating were analyzed by energy dispersive X-ray spectroscopy (EDX), SEM and XRD. The typical microstructure of composite coating is composed of TiB{sub 2}, Ti{sub 3}B{sub 4}, Al{sub 3}Ti, Al{sub 3}Fe and {alpha}-Al. The surface hardness of cladding coating is increased with the amount of added Fe coated B and Ti powder which determines the amount of TiB{sub 2} and Ti{sub 3}B{sub 4} peritectic composite particulate, and obviously higher than that of substrate. The wear tests were carried out using a FALEX-6 type pin-on-disc machine. The test results show that the composite coatings with the in situ synthesized TiB{sub 2} and Ti{sub 3}B{sub 4} peritectic improve wear resistance when compared with the as-received Al substrate.
Fagotipagem de cepas de Staphylococcus aureus resistentes a antibióticos, isoladas de leite
Directory of Open Access Journals (Sweden)
Wanderley Pereira de Araújo
1998-01-01
Full Text Available A partir de amostras de leite cru foram isoladas 201 cepas de S. aureus, as quais foram submetidas a provas de resistência a antibióticos pelo método dos discos impregnados com os seguintes antibacterianos: amicacina, ampicilina, cefalotina, cefoxitina, cloranfenicol, clindamicina, oxacilina, penicilina, tetraciclina, tobramicina e vancomicina. Com exceção de 88 (43,8%, 90 (44,8%, 24 (11,9% e 40 (19,9% cepas resistentes à penicilina, ampicilina, cloranfenicol e tetraciclina, respectivamente, a maioria das 201 cepas (95% ou mais foi sensível aos antibióticos utilizados. As cepas resistentes a estes quatro antibióticos foram fagotipadas, empregando-se os Conjuntos Básicos Internacionais de bacteriófagos para cepas de origem humana e bovina, verificando-se que houve predomínio de cepas sensíveis a fagos dos grupos III e III/NC do conjunto básico humano e a fagos dos grupos III, IV e da associação III/IV do conjunto bovino.
Directory of Open Access Journals (Sweden)
CECILIA PEÑACOBA PUENTE
2005-01-01
Full Text Available La medicina paliativa se dedica al cuidado de los pacientes con enfermedades en fase terminal. En España, existen varias unidades de cuidados paliativos, sin embargo, no en todas se lleva a cabo una intervención multidisciplinaria lo cual es esencial para conseguir que una persona muera en una situación de bienestar y con la mejor calidad posible. El objetivo de este estudio es analizar las estrategias de afrontamiento existentes en los enfermos ingresados en unidades de cuidados paliativos en fase de aceptación y su relación con la personalidad resistente. Para ello, se administró un instrumento corto en forma de entrevista. Los resultados encontrados muestran que este tipo de pacientes utilizan estrategias de afrontamiento positivas como acción para resolver problemas, búsqueda de recompensas alternativas y reevaluación positiva. Por otro lado, un aspecto de la personalidad resistente encontrada en estos pacientes es el reto lo cual indica que estos pacientes viven esta experiencia como una oportunidad de desarrollo personal.
Tecidos moles (não resistentes: como se fossilizam?
Directory of Open Access Journals (Sweden)
Silvia Regina Gobbo
2015-06-01
Full Text Available A preservação de tecidos moles (não resistentes desperta atenção pela qualidade dos fósseis preservados, e pela raridade. Este trabalho faz ampla revisão do assunto, desfaz alguns dos mitos correntes sobre fossilização destes materiais, como anaerobiose e soterramento rápido, bem como assinala a relevância do papel da replicagem de estruturas morfológicas por colônias microbianas. No âmbito dos fatores que influenciam a preservação de tecidos não resistentes estão pH, processos de decomposição, soterramento rápido e mineralização rápida por meio de carbonatos ou fosfatos. É possível citar exemplos de fácies sedimentares nas quais há preservação de tecidos não resistentes, como os folhelhos pirobetuminosos, calcários litográficos, folhelhos e diatomitos. Destaca-se o papel das colônias microbianas, tanto na forma de microesferas, como aquelas não-esferulíticas. Os três mitos principais que se procurou desfazer no artigo são: (1 a presença de oxigênio; (2 o soterramento rápido e (3 as colônias microbianas.
Joule heating of Fe-B metallic glasses
Energy Technology Data Exchange (ETDEWEB)
Miglierini, M.; Sitek, J.; Lipka, J. (Dept. of Nuclear Physics and Technology, Slovak Technical Univ., Bratislava, Slovak Republic (Czechoslovakia))
1993-04-01
Amorphous Fe[sub 80]B[sub 20] and Fe[sub 83]B[sub 17] ribbons were heated in air and in vacuum, respectively, by a dc electric current passing through the specimen. During the Joule heating, [sup 57]Fe transmission Moessbauer spectra were recorded. Ribbons of the same geometrical dimensions, cut from a natural iron foil, were treated in the same way as a reference. The influence of the current-induced magnetic field in addition to the Joule heating is supposed to cause fluctuations in a short-range order observed. Changes in the hyperfine magnetic fields are compared with those obtained by a conventional heating in a vacuum furnace. (orig.).
Joule heating of Fe-B metallic glasses
International Nuclear Information System (INIS)
Miglierini, M.; Sitek, J.; Lipka, J.
1993-01-01
Amorphous Fe 80 B 20 and Fe 83 B 17 ribbons were heated in air and in vacuum, respectively, by a dc electric current passing through the specimen. During the Joule heating, 57 Fe transmission Moessbauer spectra were recorded. Ribbons of the same geometrical dimensions, cut from a natural iron foil, were treated in the same way as a reference. The influence of the current-induced magnetic field in addition to the Joule heating is supposed to cause fluctuations in a short-range order observed. Changes in the hyperfine magnetic fields are compared with those obtained by a conventional heating in a vacuum furnace. (orig.)
Stress impedance effects in flexible amorphous FeCoSiB magnetoelastic films
International Nuclear Information System (INIS)
Zhang Wanli; Peng Bin; Su Ding; Tang Rujun; Jiang Hongchuan
2008-01-01
Amorphous FeCoSiB films were deposited on the flexible polyimide substrates (Kapton type (VN)) by DC magnetron sputtering. Stress impedance (SI) effects of the flexible amorphous FeCoSiB magnetoelastic films were investigated in details. The results show that a large stress impedance effect can be observed in the flexible amorphous FeCoSiB magnetoelastic films. And the results also show a bias magnetic field plays an important role in the stress impedance of FeCoSiB films. Applied a bias magnetic field during depositing can induce obvious in-plane anisotropy in the FeCoSiB films, and a larger SI effect can be obtained with a stronger anisotropy in FeCoSiB films. Argon pressure has a significant effect on the SI effect of the FeCoSiB films. The SI of the FeCoSiB films reaches a maximum of 7.6% at argon pressure of 1.5 Pa, which can be explained by the change of residual stress in FeCoSiB films
Developments with melt spun RE-Fe-B powder for bonded magnets
International Nuclear Information System (INIS)
Brown, D.N.; Chen, Z.; Guschl, P.; Campbell, P.
2006-01-01
Rapidly quenched isotropic rare earth iron boride (RE-Fe-B) powders have found many applications throughout the electronics, automotive and white goods industries. The magnetic performance, thermal stability, corrosion resistance and processability of a powder are important factors when selecting a RE-Fe-B powder for a particular application. For electronic devices that operate at ambient temperatures, high remanence (B r ) tends to be a priority and RE 2 Fe 14 B/α-Fe nanocomposite powder magnets are favoured. Alternatively, automotive applications tend to require greater thermal stability and corrosion resistance, which are satisfied by single-phase RE 2 Fe 14 B powder magnets with higher intrinsic coercivity (H ci ). This article reviews the performance of commercially available rapidly solidified RE-Fe-B powders and recent developments made to address the demands of applications
International Nuclear Information System (INIS)
Liu, Yue-Lin; Yu, Yang; Dai, Zhen-Hong
2015-01-01
Using first-principles calculations, we investigate the stabilities of He and He n -vacancy (He n V) clusters in α-Fe and W. Vacancy formation energies are 2.08 eV in α-Fe and 3.11 eV in W, respectively. Single He in both α-Fe and W prefers to occupy the tetrahedral interstitial site. We recalculated the He solution energy considering the effect of zero-point energy (ZPE). The ZPEs of He in α-Fe and W at the tetrahedral (octahedral) interstitial site are 0.072 eV (0.031 eV) and 0.078 eV (0.034 eV), respectively. The trapping energies of single He at vacancy in α-Fe and W are −2.39 eV and −4.55 eV, respectively. By sequentially adding He into vacancy, a monovacancy trap up to 10 He atoms distributing in the vacancy vicinity. Based on the above results combined with statistical model, we evaluate the concentrations of all relevant He n V clusters as a function of He chemical potential. The critical He n V concentration is found to be ∼10 −40 (atomic) at the critical temperature T = 600 K in α-Fe and T = 1600 K in W, respectively. Beyond the critical He n V concentrations, considerable He n V aggregate to form He n V m clusters. By further growing of He n V m , the He n V m clusters grow bigger resulting in the larger He bubble formation
Asymmetric angular dependence of spin-transfer torques in CoFe/Mg-B-O/CoFe magnetic tunnel junctions
Energy Technology Data Exchange (ETDEWEB)
Tang, Ling, E-mail: lingtang@zjut.edu.cn; Xu, Zhi-Jun, E-mail: xzj@zjut.edu.cn; Zuo, Xian-Jun; Yang, Ze-Jin, E-mail: zejinyang@zjut.edu.cn [Department of Applied Physics, College of Science, Zhejiang University of Technology, Hangzhou 310023 (China); Gao, Qing-He [College of Science, Northeastern University, Shenyang 110004, China, Information Engineering College, Liaoning University of Traditional Chinese Medicine, Shenyang 110847 (China); Linghu, Rong-Feng, E-mail: linghu@gznu.edu.cn [School of Physics and Electronics Sciences, Guizhou Education University, Guiyang 550018 (China); Guo, Yun-Dong, E-mail: g308yd@126.com [College of Engineering and Technology, Neijiang Normal University, Neijiang 641112 (China)
2016-04-28
Using a first-principles noncollinear wave-function-matching method, we studied the spin-transfer torques (STTs) in CoFe/Mg-B-O/CoFe(001) magnetic tunnel junctions (MTJs), where three different types of B-doped MgO in the spacer are considered, including B atoms replacing Mg atoms (Mg{sub 3}BO{sub 4}), B atoms replacing O atoms (Mg{sub 4}BO{sub 3}), and B atoms occupying interstitial positions (Mg{sub 4}BO{sub 4}) in MgO. A strong asymmetric angular dependence of STT can be obtained both in ballistic CoFe/Mg{sub 3}BO{sub 4} and CoFe/Mg{sub 4}BO{sub 4} based MTJs, whereas a nearly symmetric STT curve is observed in the junctions based on CoFe/Mg{sub 4}BO{sub 3}. Furthermore, the asymmetry of the angular dependence of STT can be suppressed significantly by the disorder of B distribution. Such skewness of STTs in the CoFe/Mg-B-O/CoFe MTJs could be attributed to the interfacial resonance states induced by the B diffusion into MgO spacer.
International Nuclear Information System (INIS)
Hirosawa, S.; Kanekiyo, H.; Ping, D.H.; Hono, K.
1998-01-01
Thick permanent magnet flakes of Fe 3 B/Nd 2 Fe 14 B nanocomposites have been produced directly from molten alloys by means of the low surface-velocity melt spinning technique. The thickness of the flakes varies from 70 to 300 μm depending on the surface velocity (V s ) of a quenching copper roll. Melt-spun flakes of Nd 4 Fe 77.5 B 18.5 alloy exhibit the intrinsic coercivity of 276 kA/m at V s of 5 m/s. X-ray diffraction and transmission electron microscopy results have revealed that this material is composed of nanocrystalline Fe 3 B and Nd 2 Fe 14 B grains ranging from 10 to 50 nm in diameter. The melt-spun alloy produced at V s = 3 m/s contains large grains of Nd 2 Fe 14 B, small grains of Fe 3 B, and large dendritic α-Fe of a few μm in length. In contrast, at V s = 7 m/s, a large portion of the quenched alloy is amorphous. These melt-spun alloys do not possess a hard magnetic property. We have also found that small additions of additives affect the optimum range of V s that give rise to hard magnetic properties in the as-melt-spun condition. Cr has a large effect in shifting the optimum V s values down to a 2-3 m/s range. Simultaneous addition of Co and Ga is effective in extending the optimum values of V s . A platelet permanent magnet with a thickness of 240 μm and magnetic properties of (BH) max = 131 kJ/m 3 , H cJ = 400 kA/m, and B r = 1.15 T has been produced from a Nd 3.5 Dy 1 Fe 73 Co 3 Ga 1 B 18.5 alloy. (orig.)
Hydrocyclone Separation of Hydrogen Decrepitated NdFeB
Directory of Open Access Journals (Sweden)
Muhammad Awais
2017-11-01
Full Text Available Hydrogen decrepitation (HD is an effective and environmentally friendly technique for recycling of neodymium-iron-boron (NdFeB magnets. During the HD process, the NdFeB breaks down into a matrix phase (Nd2Fe14BHx and RE-rich grain boundary phase. The grain boundary phase in the HD powder is <2 μm in size. Recycled NdFeB material has a higher oxygen content compared to the primary source material. This additional oxygen mainly occurs at the Rare Earth (RE rich grain boundary phase (GBP, because rare earth elements oxidise rapidly when exposed to air. This higher oxygen level in the material results in a drop in density, coercivity, and remanence of sintered NdFeB magnets. The particle size of the GBP is too small to separate by sieving or conventional screening technology. In this work, an attempt has been made to separate the GBP from the matrix phase using a hydrocyclone, and to optimise the separation process. HD powder, obtained from hard disk drive (HDD scrap NdFeB sintered magnets, was used as a starting material and passed through a hydrocyclone a total number of six times. The X-ray fluorescence (XRF analysis and sieve analysis of overflows showed the matrix phase had been directed to the underflow while the GBP was directed to the overflow. The optimum separation was achieved with three passes. Underflow and overflow samples were further analysed using an optical microscope and MagScan and matrix phase particles were found to be magnetic.
Liu, B; Zheng, Y F
2011-03-01
Pure iron was determined to be a valid candidate material for biodegradable metallic stents in recent animal tests; however, a much faster degradation rate in physiological environments was desired. C, Mn, Si, P, S, B, Cr, Ni, Pb, Mo, Al, Ti, Cu, Co, V and W are common alloying elements in industrial steels, with Cr, Ni, Mo, Cu, Ti, V and Si being acknowledged as beneficial in enhancing the corrosion resistance of iron. The purpose of the present work (using Fe-X binary alloy models) is to explore the effect of the remaining alloying elements (Mn, Co, Al, W, B, C and S) and one detrimental impurity element Sn on the biodegradability and biocompatibility of pure iron by scanning electron microscopy, X-ray diffraction, metallographic observation, tensile testing, microhardness testing, electrochemical testing, static (for 6 months) and dynamic (for 1 month with various dissolved oxygen concentrations) immersion testing, cytotoxicity testing, hemolysis and platelet adhesion testing. The results showed that the addition of all alloying elements except for Sn improved the mechanical properties of iron after rolling. Localized corrosion of Fe-X binary alloys was observed in both static and dynamic immersion tests. Except for the Fe-Mn alloy, which showed a significant decrease in corrosion rate, the other Fe-X binary alloy corrosion rates were close to that of pure iron. It was found that compared with pure iron all Fe-X binary alloys decreased the viability of the L929 cell line, none of experimental alloying elements significantly reduced the viability of vascular smooth muscle cells and all the elements except for Mn increased the viability of the ECV304 cell line. The hemolysis percentage of all Fe-X binary alloy models were less than 5%, and no sign of thrombogenicity was observed. In vitro corrosion and the biological behavior of these Fe-X binary alloys are discussed and a corresponding mechanism of corrosion of Fe-X binary alloys in Hank's solution proposed. As a
International Nuclear Information System (INIS)
Elzo, M.; Jal, E.; Bunau, O.; Grenier, S.; Joly, Y.; Ramos, A.Y.; Tolentino, H.C.N.; Tonnerre, J.M.; Jaouen, N.
2012-01-01
A formalism for the reflectivity of electromagnetic waves by magnetic materials is presented with an application. It is applied to retrieve the magnetic moment density along the depth of magnetic materials with arbitrary magnetic moment direction using matricial algebra, including roughness between layers. The reflectivity is derived following a classical description with Maxwell equations and a permittivity built from the quantum scattering amplitude. Approximations on the relative power of the Thomson scattering and the magnetic terms are trackable in order to evaluate the validity of the formalism case-by-case, from the optical light regime up to soft and hard X-rays. Eigenwaves are used throughout the whole formalism. In order to illustrate the methodology, we present an application to a W/Fe/W trilayer performed at the Fe L-edge, in the soft X-ray regime. - Highlights: → Magnetism at interfaces and in thin films is increasingly studied. → X-ray resonant magnetic reflectivity yields the in depth magnetization profile in thin films. → We present a formalism and methodology to study the data. → We illustrate the technique with an example.
Ce-didymium-Fe-B sintered permanent magnets
International Nuclear Information System (INIS)
Homma, M.; Okada, M.; Sugimoto, S.
1985-01-01
Present works report the development of the low cost R-Fe-B permanent magnets. The best magnetic properties obtained in this studies are Br=13.5 kG, iHc=10.2 kOe and (BH)max=40 MGOe with an Fe-33.5wt%(5Ce-Didymium)-1wt% B alloy. Topics considered in this paper include cerium alloys, boron alloys, fabrication, capitalized cost, iron alloys, permanent magnets, and magnetic properties
Point defects in B.C.C. Fe-Al, Fe-Co, and Fe-Co-V ordered alloys
International Nuclear Information System (INIS)
Riviere, J.P.; Dinhut, J.F.
1982-01-01
Radiation damage produced at 20 K by 2.5 MeV electrons is studied in three B 2 type Fe-40 at % Al, Fe-Co, Fe-Co-V ordered alloys. The resistivity damage in Fe-40 at % Al ordered single crystals is found less effective in the directions. The results suggest that replacement collision chains are difficult to propagate along the direction. Frenkel pair creation superimposed with disordering can account for the resistivity damage in the initially ordered Fe-Co alloy. Informations concerning replacement collision sequences in direction are derived. During the recovery of all the alloys, three main stages are observed and an ordering enhancement occurs. (author)
International Nuclear Information System (INIS)
Karen, P.; Kjekshus, A.; Huang, Q.; Karen, V.L.; Lynn, J.W.; Rosov, N.; Natali Sora, I.; Santoro, A.
2003-01-01
YBa 2 Fe 3 O 8+w has been investigated by neutron powder diffraction as function of temperature and oxygen nonstoichiometry close to the limits of the homogeneity range, -0.24 0) in the structural layers of Y, or by creating oxygen vacancies (w 2 Cu 3 O 6+w' upon oxidation. The effects of nonstoichiometry on these related crystal structures are discussed in terms of bond-valence sums. The cooperative magnetic structure for all compositions is based on a larger cell related to the nuclear cell by the transformation matrix (11-bar0/110/002), having orthorhombic symmetry when the nuclear structure is tetragonal and monoclinic symmetry when the nuclear structure is orthorhombic. The iron moments are coupled antiferromagnetically in all three directions, the Neel temperature is almost constant as a function of w (T N ∼660 K), and so is also the low-temperature saturation moment μ AF ∼4.0μ B
Directory of Open Access Journals (Sweden)
Yimo eLiu
2015-10-01
Full Text Available The tandem gene clusters orfR-ombB-omaB-omcB and orfS-ombC-omaC-omcC of the metal-reducing bacterium Geobacter sulfurreducens PCA are responsible for trans-outer membrane electron transfer during extracellular reduction of Fe(III-citrate and ferrihydrite [a poorly crystalline Fe(III oxide]. Each gene cluster encodes a putative transcriptional factor (OrfR/OrfS, a porin-like outer-membrane protein (OmbB/OmbC, a periplasmic c-type cytochrome (c-Cyt, OmaB/OmaC and an outer-membrane c-Cyt (OmcB/OmcC. The individual roles of OmbB, OmaB and OmcB in extracellular reduction of Fe(III, however, have remained either uninvestigated or controversial. Here, we showed that replacements of ombB, omaB, omcB and ombB-omaB with an antibiotic gene in the presence of ombC-omaC-omcC had no impact on reduction of Fe(III-citrate by G. sulfurreducens PCA. Disruption of ombB, omaB, omcB and ombB-omaB in the absence of ombC-omaC-omcC, however, severely impaired the bacterial ability to reduce Fe(III-citrate as well as ferrihydrite. These results unequivocally demonstrate an overlapping role of ombB-omaB-omcB and ombC-omaC-omcC in extracellular Fe(III reduction by G. sulfurreducens PCA. Involvement of both ombB-omaB-omcB and ombC-omaC-omcC in extracellular Fe(III reduction reflects the importance of these trans-outer membrane protein complexes in the physiology of this bacterium. Moreover, the kinetics of Fe(III-citrate and ferrihydrite reduction by these mutants in the absence of ombC-omaC-omcC were nearly identical, which suggests that absence of any protein subunit eliminates function of OmaB/OmbB/OmcB protein complex. Finally, orfS was found to have a negative impact on the extracellular reduction of Fe(III-citrate and ferrihydrite in G. sulfurreducens PCA probably by serving as a transcriptional repressor.
Microstructure and magnetic properties of Nd-Fe-B-(Re, Ti alloys
Directory of Open Access Journals (Sweden)
Hasiak Mariusz
2015-03-01
Full Text Available The microstructure and magnetic properties of nanocomposite hard magnetic Nd-Fe-B-(Re, Ti materials with different Nd and Fe contents are studied. The role of Re and Ti addition in phase composition and volume fraction of the Nd-Fe-B phase is determined. All samples are annealed at the same temperature of 993 K for 10 min. Mössbauer spectroscopy shows that the addition of 4 at.% of Re to the Nd8Fe78B14 alloy leads to creation of an ineligible amount of the magnetically hard Nd2Fe14B phase. Moreover, the microstructure and magnetic characteristics recorded in a wide range of temperatures for the Nd8Fe79−xB13Mx (x = 4; M = Re or Ti alloys are also analyzed.
Dirac State in the FeB2 Monolayer with Graphene-Like Boron Sheet.
Zhang, Haijun; Li, Yafei; Hou, Jianhou; Du, Aijun; Chen, Zhongfang
2016-10-12
By introducing the commonly utilized Fe atoms into a two-dimensional (2D) honeycomb boron network, we theoretically designed a new Dirac material of FeB 2 monolayer with a Fermi velocity in the same order of graphene. The electron transfer from Fe atoms to B networks not only effectively stabilizes the FeB 2 networks but also leads to the strong interaction between the Fe and B atoms. The Dirac state in FeB 2 system primarily arises from the Fe d orbitals and hybridized orbital from Fe-d and B-p states. The newly predicted FeB 2 monolayer has excellent dynamic and thermal stabilities and is also the global minimum of 2D FeB 2 system, implying its experimental feasibility. Our results are beneficial to further uncovering the mechanism of the Dirac cones and providing a feasible strategy for Dirac materials design.
Energy Technology Data Exchange (ETDEWEB)
Huynh, Xuan-Khoa [Hanoi Uneversity of Science and Technology, Hanoi (Viet Nam); Bae, Sun-Woo; Kim, Ji Soon [University of Ulsan, Ulsan (Korea, Republic of)
2017-01-15
Fe-TiB{sub 2} powder was synthesized in-situ by the planetary ball milling and subsequent heat-treatment of an iron boride (FeB) and titanium hydride (TiH{sub 2}) powder mixture. Mechanical activation of the (FeB+TiH{sub 2}) powder mixtures was observed after a milling time of 3 hours at 700 rpm of rotation speed, but activation was not the same after 1 hour milling time. The particle size of the (FeB+ TiH{sub 2}) powder mixture was reduced to the nanometer scale, and each constituent was homogeneously distributed. A sharp exothermic peak was observed at a lower temperature (749 ℃) on the DSC curves for the (FeB+TiH{sub 2}) powder mixture milled for 3 hours, compared to the one milled for 1 hour (774 ℃). These peaks were confirmed to have resulted from the formation reaction of the TiB{sub 2} phase, from Ti and B elements in the FeB. The Fe-TiB{sub 2} composite powder fabricated in situ exhibited only two phases of Fe and TiB{sub 2} with homogeneous distribution. The size of the TiB{sub 2} particulates in the Fe matrix was less than 5 nm.
Miniature Inchworm Actuators Fabricated by Use of LIGA
Yang, Eui-Hyeok
2003-01-01
Miniature inchworm actuators that would have relatively simple designs have been proposed for applications in which there are requirements for displacements of the order of microns or tens of microns and for the ability to hold their positions when electric power is not applied. The proposed actuators would be members of the class of microelectromechanical systems (MEMS), but would be designed and fabricated following an approach that is somewhat unusual for MEMS. Like other MEMS actuators, the proposed inchworm actuators could utilize thermoplastic, bimetallic, shape-memory-alloy, or piezoelectric actuation principles. The figure depicts a piezoelectric inchworm actuator according to the proposal. As in other inchworm actuators, linear motion of an extensible member would be achieved by lengthening and shortening the extensible member in synchronism with alternately clamping and releasing one and then the other end of the member. In this case, the moving member would be the middle one; the member would be piezoelectric and would be shortened by applying a voltage to it. The two outer members would also be piezoelectric; the release of the clamps on the upper or lower end would be achieved by applying a voltage to the electrodes on the upper or lower ends, respectively, of these members. Usually, MEMS actuators cannot be fabricated directly on the side walls of silicon wafers, yet the geometry of this actuator necessitates such fabrication. The solution, according to the proposal, would be to use the microfabrication technique known by the German acronym LIGA - "lithographie, galvanoformung, abformung," which means lithography, electroforming, molding. LIGA involves x-ray lithography of a polymer film followed by selective removal of material to form a three-dimensional pattern from which a mold is made. Among the advantages of LIGA for this purpose are that it is applicable to a broad range of materials, can be used to implement a variety of designs, including
Thin films of NdFeB deposited by PLD technique
International Nuclear Information System (INIS)
Constantinescu, C.; Scarisoreanu, N.; Moldovan, A.; Dinescu, M.; Petrescu, L.; Epureanu, G.
2007-01-01
Neodymium-iron-boron (NdFeB) is a material with important magnetic properties, mostly used in permanent magnet fabrication. Thin layers of NdFeB are needed for miniaturization in electrical engineering, electronics and for high-tech devices. In this paper we applied pulsed lased deposition (PLD) in vacuum for obtaining thin films of NdFeB from stoichiometric targets. The influence of different buffer layers and of the laser parameters (wavelength and fluence) on the NdFeB structures, composition and magnetic properties have been investigated. The obtained structures were characterized by atomic force microscopy (AFM) and optical microscopy. Vibrating sample magnetometry (VSM) has been performed for specific magnetic characterization
Thin films of NdFeB deposited by PLD technique
Energy Technology Data Exchange (ETDEWEB)
Constantinescu, C. [National Institute for Laser, Plasma and Radiation Physics, P.O. Box MG 16, RO-077125 Magurele, Bucharest (Romania); Scarisoreanu, N. [National Institute for Laser, Plasma and Radiation Physics, P.O. Box MG 16, RO-077125 Magurele, Bucharest (Romania); Moldovan, A. [National Institute for Laser, Plasma and Radiation Physics, P.O. Box MG 16, RO-077125 Magurele, Bucharest (Romania); Dinescu, M. [National Institute for Laser, Plasma and Radiation Physics, P.O. Box MG 16, RO-077125 Magurele, Bucharest (Romania)]. E-mail: dinescum@ifin.nipne.ro; Petrescu, L. [Department of Electrical Engineering, ' Politehnica' University of Bucharest, 313 Spl. Independentei, 060042 Bucharest (Romania); Epureanu, G. [Department of Electrical Engineering, ' Politehnica' University of Bucharest, 313 Spl. Independentei, 060042 Bucharest (Romania)
2007-07-31
Neodymium-iron-boron (NdFeB) is a material with important magnetic properties, mostly used in permanent magnet fabrication. Thin layers of NdFeB are needed for miniaturization in electrical engineering, electronics and for high-tech devices. In this paper we applied pulsed lased deposition (PLD) in vacuum for obtaining thin films of NdFeB from stoichiometric targets. The influence of different buffer layers and of the laser parameters (wavelength and fluence) on the NdFeB structures, composition and magnetic properties have been investigated. The obtained structures were characterized by atomic force microscopy (AFM) and optical microscopy. Vibrating sample magnetometry (VSM) has been performed for specific magnetic characterization.
DEFF Research Database (Denmark)
Dideriksen, Knud; Baker, Joel A.; Stipp, Susan Louise Svane
2008-01-01
be controlled by isotope fractionation between the free and complexed iron.We have determined the equilibrium Fe isotope fractionation induced by organic ligand activity in experiments with solutions having co-existing inorganic Fe(III) species and siderophore complexes, Fedesferrioxamine B (at pH 2). The two......-type fractionation during precipitation, this experiment yielded an isotope fractionation factor of a56Fesolution-solid=1.00027. Calculations based on these results indicate that isotopic re-equilibration is unlikely to significantly affect our determined equilibrium Fe isotope fractionation between inorganically...... and organically complexed Fe. To determine the equilibrium Fe isotope fractionation between inorganically and organically bound Fe(III), experiments with variable proportions of inorganic Fe were carried out at 25 °C. Irrespective of the proportion of inorganic Fe, equilibrium fractionation factors were within...
International Nuclear Information System (INIS)
Wang Shiliang; He Yuehui; Zou Jou; Wang Yong; Huang Han
2009-01-01
Numbers of W whiskers were obtained by reducing Ni, Ni-Fe, and Ni-Co doped tungsten oxide in a mixed atmosphere of humid H 2 and N 2 . The phases and morphologies of the reduction products were characterized by XRD and SEM. Intensive TEM and EDS analyses showed that the obtained whiskers were W single crystals which typical have alloyed particles (Ni-W, Fe-Ni, or Co-Ni-W) at the growth tips. The formed W whiskers were presumed to be induced by the alloyed particles. Our experimental results revealed that, during the reduction process of tungsten oxide, the pre-reduced Ni, Fe-Ni, or Co-Ni particles not only served as nucleation aids for the initial growth of W phase from W oxide but also played the roles of catalysts during the reductive decomposition of gaseous WO 2 (OH) 2 .
Characterization of nanocomposite NdFeB permanent magnetic materials
International Nuclear Information System (INIS)
Mat Husin Salleh; Hussain, P.; Mohammad, M.; Abd Aziz Mohamed
2005-01-01
The following topics were discussed: Introduction to NdFeB magnet, grain size measurement using XRD (X-ray diffraction), FESEM , TEM (Transmission Electron Microscopy) and SANS (Small-angle Neutron Scattering). The objective of the project are to analyze the structure of nano-crystallite formed in the melt spun ribbons after annealing by XRD, FESEM,TEM and SANS, to study the magnetic properties of nano-composite NdFeB melt spun ribbons and their bonded magnet and possible usage in small motor to replace the conventional NdFeB bonded magnet
International Nuclear Information System (INIS)
Shiojiri, M.; Sekimoto, S.; Maeda, T.; Ikeda, Y.; Iwauchi, K.
1984-01-01
The crystal structure of metal pseudobrookite, Fe 2 TiO 5 , is determined from high-resolution electron microscopy images observed and their computer simulated images, with the aid of electron diffraction and X-ray powder diffraction. The new structure has a monoclinic unit, containing eight molecules, with a = 2.223, b = 0.373, c = 0.980 nm, and β = 116.2 0 . The Fe, Ti, and O atoms occupy the positions (4c), +-(u, 0, w; 1/2 + u, 1/2, w), of C 2 3 (C2). The most probable parameters u and w, of Fe(1 to 4), Ti(1, 2), and O(1 to 10) are given. (author)
Strength anomaly in B2 FeAl single crystals
Energy Technology Data Exchange (ETDEWEB)
Yoshimi, K.; Hanada, S.; Yoo, M.H. [Oak Ridge National Lab., TN (United States); Matsumoto, N. [Tohoku Univ. (Japan). Graduate School
1994-12-31
Strength and deformation microstructure of B2 Fe-39 and 48%Al single crystals (composition given in atomic percent), which were fully annealed to remove frozen-in vacancies, have been investigated at temperatures between room temperature and 1073K. The hardness of as-homogenized Fe-48Al is higher than that of as-homogenized Fe-39Al while after additional annealing at 698K the hardness of Fe-48Al becomes lower than that of Fe-39Al. Fe-39Al single crystals slowly cooled after homogenizing at a high temperature were deformed in compression as a function of temperature and crystal orientation. A peak of yield strength appears around 0.5T{sub m} (T{sub m} = melting temperature). The orientation dependence of the critical resolved shear stress does not obey Schmid`s law even at room temperature and is quite different from that of b.c.c. metals and B2 intermetallics at low temperatures. At the peak temperature slip transition from <111>-type to <001>-type is found to occur macroscopically and microscopically, while it is observed in TEM that some of the [111] dislocations decompose into [101] and [010] on the (1096I) plane below the peak temperature. The physical sources for the positive temperature dependence of yield stress of B2 FeAl are discussed based on the obtained results.
Magnetization switching diagram of a perpendicular synthetic ferrimagnet CoFeB/Ta/CoFeB bilayer
Energy Technology Data Exchange (ETDEWEB)
Koplak, O. [Immanuel Kant Baltic Federal University, 236041 Kaliningrad (Russian Federation); Institute of Problems of Chemical Physics, 142432 Chernogolovka, Moscow (Russian Federation); Talantsev, A. [Institute of Problems of Chemical Physics, 142432 Chernogolovka, Moscow (Russian Federation); Lu, Y.; Hamadeh, A.; Pirro, P.; Hauet, T. [Institut Jean Lamour, UMR 7198 CNRS, Université de Lorraine (France); Morgunov, R., E-mail: morgunov2005@yandex.ru [Institute of Problems of Chemical Physics, 142432 Chernogolovka, Moscow (Russian Federation); Tambov State Technical University, 392000 Tambov (Russian Federation); Mangin, S. [Institut Jean Lamour, UMR 7198 CNRS, Université de Lorraine (France)
2017-07-01
Highlights: • Anisotropy, Zeeman and exchange energy determine sequence of magnetic transitions. • Three temperature ranges manifest different shapes of the hysteresis loop. • The critical transition fields are temperature dependent. - Abstract: Magnetic configurations in synthetic ferrimagnet CoFeB/Ta/CoFeB bilayer with strong perpendicular anisotropy have been systematically studied. Magnetization versus field hysteresis loop has been measured for different temperature ranging from 5 to 300 K. The applied field – temperature (H-T) magnetization switching diagram has been constructed by extracting the different switching fields as a function of temperature. This switching diagram can be well explained by considering the competition between energy barrier of layer’s magnetization reversal, interlayer exchange coupling, and Zeeman energy.
Magnetization switching diagram of a perpendicular synthetic ferrimagnet CoFeB/Ta/CoFeB bilayer
International Nuclear Information System (INIS)
Koplak, O.; Talantsev, A.; Lu, Y.; Hamadeh, A.; Pirro, P.; Hauet, T.; Morgunov, R.; Mangin, S.
2017-01-01
Highlights: • Anisotropy, Zeeman and exchange energy determine sequence of magnetic transitions. • Three temperature ranges manifest different shapes of the hysteresis loop. • The critical transition fields are temperature dependent. - Abstract: Magnetic configurations in synthetic ferrimagnet CoFeB/Ta/CoFeB bilayer with strong perpendicular anisotropy have been systematically studied. Magnetization versus field hysteresis loop has been measured for different temperature ranging from 5 to 300 K. The applied field – temperature (H-T) magnetization switching diagram has been constructed by extracting the different switching fields as a function of temperature. This switching diagram can be well explained by considering the competition between energy barrier of layer’s magnetization reversal, interlayer exchange coupling, and Zeeman energy.
He, Wei; Zhu, Tao; Zhang, Xiang-Qun; Yang, Hai-Tao; Cheng, Zhao-Hua
2013-10-07
The laser-induced ultrafast demagnetization of CoFeB/MgO/CoFeB magnetic tunneling junction is exploited by time-resolved magneto-optical Kerr effect (TRMOKE) for both the parallel state (P state) and the antiparallel state (AP state) of the magnetizations between two magnetic layers. It was observed that the demagnetization time is shorter and the magnitude of demagnetization is larger in the AP state than those in the P state. These behaviors are attributed to the ultrafast spin transfer between two CoFeB layers via the tunneling of hot electrons through the MgO barrier. Our observation indicates that ultrafast demagnetization can be engineered by the hot electrons tunneling current. It opens the door to manipulate the ultrafast spin current in magnetic tunneling junctions.
Directory of Open Access Journals (Sweden)
Carlos Alberto Mendoza Ticona
2003-10-01
Full Text Available Objetivo: Determinar las susceptibilidad a diversos antibacterianos de tres categorías de S. aureus según su sensibilidad a la meticilina. Materiales y Métodos: Se aislaron 76 cepas de S. aureus que colonizaban pacientes y personal de salud de tres servicios del Hospital Honorio Delgado de Arequipa, de los cuales 36 fueron sensibles a meticilina (MSSA, 15 con susceptibilidad "borderline" (BORSA y 25 fueron resistentes a la meticilina (MRSA. Se les sometió a antibiograma a 14 antibacterianos. Resultados: El único antibiótico al cual todas los aislamientos fueron sensibles fue vancomicina. Los MRSA fueron resistentes a todos los b-lactámicos excepto imipenem que obtuvo 64% de susceptibilidad. Los BORSA mantuvieron un 80% de sensibilidad a cefalotina y un 100% al imipenem. Los antibióticos cefalotina, imipenem, ciprofloxacina, cotrimoxazol, rifampicina, eritromicina, tetraciclina, cloranfenicol, lincomicina y gentamicina tuvieron sensibilidades variables (p<0.01 entre las tres categorías; una mayor proporción de MSSA fue sensible a estos antibióticos, luego los BORSA y finalmente los MRSA. Las cepas multi-resistentes fueron mucho más frecuentes en los MRSA que en los otros dos grupos (p <0.01. Conclusión: Existe en nuestro medio cepas de S. aureus con resistencia "borderline" a meticilina. Hay diferencias entre la sensibilidad a diversos antimicrobianos entre los tres grupos de S. aureus. Esta diferenciación podría beneficiar una terapia antimicrobiana más racional. Se debe aplicar en todo aislamiento de S. aureus las recomendaciones internacionales para la detección de meticilino resistencia.
Arquitectura sismo-resistente: respuesta morfológica
Directory of Open Access Journals (Sweden)
Giulani, Hugo
1994-12-01
Full Text Available In the previous reports (1 and (2 we raised the question of the necessity to develop an Earthquake-Resistant Architecture which would make the integral solution of the seismic problem in buildings possible. We established the grounds, objectives, basic principles and methodology for defining the guidelines to be followed in making the architectural design and structural earthquake-resistant design compatible. The present report brings the proposal of an architectural response from the morphological point of view, allowing us to reach an adequate final form which consists of eliminating all the incompatibilities produced by the seismic demands and determining factors, in other words, we search for an architectural design which, owing to its very morphology, is able to satisfy the said conditions; an "Adequate Final Form" which in itself avoids the bothersome guidelines for making the structural and architectural designs compatible, transforming them into morphological responses to each seismic determining factor.
En informes anteriores (1 y (2 planteamos la necesidad de desarrollar una Arquitectura Sismo-resistente, que posibilite la solución integral del problema sísmico de los edificios. Se establecieron los fundamentos, objetivos, principios básicos y metodología para deducir las pautas de compatibilización del diseño arquitectónico con el diseño estructural sismo-resistente. En el presente informe se propone una respuesta arquitectónica desde la morfología, que permite llegar a una forma final ajustada, en el sentido de eliminar toda incompatibilidad respecto de las exigencias o condicionantes sísmicos. Es decir, un proyecto arquitectónico que por su propia morfología satisfaga dichos condicionantes. Una "Forma Final Ajustada" que evita, por sí misma, las engorrosas pautas de compatibilización del diseño estructural con el diseño arquitectónico, transformándolas en respuestas morfológicas a cada condicionante sísmico.
Niedokrwistość chorób przewlekłych w przebiegu reumatoidalnego zapalenia stawów
Directory of Open Access Journals (Sweden)
Justyna Fryc
2010-12-01
Full Text Available Niedokrwistość chorób przewlekłych stanowi jedno z najczęstszychzaburzeń hematologicznych obserwowanych u pacjentówz reumatoidalnym zapaleniem stawów. Stwierdza się ją takżew wielu innych procesach chorobowych, takich jak: nowotwory,choroby zakaźne i zapalne, niewydolność serca czy cukrzyca. Patogenezatego schorzenia nie jest jednak jeszcze w pełni poznana.W procesie rozwoju choroby rolę odgrywają mediatory stanuzapalnego, takie jak czynnik martwicy nowotworów α, interleukiny(IL-1, IL-6 i IL-10. Hepcydyna jest jednym z kluczowych białekw patogenezie niedokrwistości chorób przewlekłych, ponieważhamuje absorpcję żelaza oraz jego uwalnianie z makrofagów.W artykule przedstawiono patogenezę niedokrwistości choróbprzewlekłych u pacjentów z reumatoidalnym zapaleniem stawów.Celem pracy jest także podsumowanie wyników ostatnio prowadzonychbadań dotyczących roli hamowania IL-6 u pacjentówz niedokrwistością chorób przewlekłych w przebiegu reumatoidalnegozapalenia stawów. Wykazano, że blokowanie receptora dlaIL-6 z użyciem tocilizumabu prowadzi do zwiększenia stężeniahemoglobiny w porównaniu z grupą otrzymującą placebo.
Zhang, Zongyang; Liu, Xiansong; Feng, Shuangjiu; Rehman, Khalid Mehmood Ur
2018-03-01
In this study, the melt spinning method was used to develop Fe80.5Si7.5B6Nb5Cu amorphous ribbons in the first step. Then, the Fe80.5Si7.5B6Nb5Cu amorphous-nanocrystalline core with a compact microstructure was obtained by multiple processes. The main properties of the magnetic powder core, such as micromorphology, thermal behavior, permeability, power loss and quality factor, have been analyzed. The obtained results show that an Fe80.5Si7.5B6Nb5Cu amorphous-nanocrystalline duplex core has high permeability (54.8-57), is relatively stable at different frequencies and magnetic fields, and the maximum power loss is only 313 W/kg; furthermore, it has a good quality factor.
Energy Technology Data Exchange (ETDEWEB)
Ryo, Hyok-Su [School of Material Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Faculty of Physics, Kim Il Sung University, Pyongyang 999093, Democratic People’s Republic of Korea (Korea, Republic of); Hu, Lian-Xi [School of Material Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Kim, Jin-Guk [School of Material Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Faculty of Physics, Kim Il Sung University, Pyongyang 999093, Democratic People’s Republic of Korea (Korea, Republic of); Yang, Yu-Lin [School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001 (China)
2017-03-15
In this study, magnetic properties of exchange coupled nanocomposite multilayer thin films constructed alternately with magnetic hard Nd{sub 2}Fe{sub 14}B layers and soft α-Fe layers have been studied by micromagnetic finite element method (FEM). According to the results, effects of the thicknesses of layers and the magneto-crystalline anisotropy on the magnetic properties of the Nd{sub 2}Fe{sub 14}B/α-Fe multilayer systems have been estimated. On the other hand, the results have been analyzed by means of efficiency of interphase exchange coupling, which can be estimated by volume ratios of exchange coupled areas between magnetically hard Nd{sub 2}Fe{sub 14}B and soft α-Fe phase layers. The results show that the magnetic properties of exchange coupled Nd{sub 2}Fe{sub 14}B/α-Fe multilayer systems can be enhanced by efficient interphase exchange coupling between magnetically hard Nd{sub 2}Fe{sub 14}B layers and soft α-Fe layers. - Highlights: • Phase layer thicknesses dependence of magnetic properties of Nd{sub 2}Fe{sub 14}B/α-Fe multilayers. • Analyzation of the effectiveness of exchange coupling between the Nd{sub 2}Fe{sub 14}B and α-Fe layers. • Dependence of the magnetic properties on direction of external field of exchange coupled Nd{sub 2}Fe{sub 14}B/α-Fe multilayers. • Dependence of the magnetic properties on magneto-crystalline anisotropy of exchange coupled Nd{sub 2}Fe{sub 14}B/α-Fe multilayers.
Silva, Everton F; Medeiros, Marco A; McBride, Alan J A; Matsunaga, Jim; Esteves, Gabriela S; Ramos, João G R; Santos, Cleiton S; Croda, Júlio; Homma, Akira; Dellagostin, Odir A; Haake, David A; Reis, Mitermayer G; Ko, Albert I
2007-08-14
Subunit vaccines are a potential intervention strategy against leptospirosis, which is a major public health problem in developing countries and a veterinary disease in livestock and companion animals worldwide. Leptospiral immunoglobulin-like (Lig) proteins are a family of surface-exposed determinants that have Ig-like repeat domains found in virulence factors such as intimin and invasin. We expressed fragments of the repeat domain regions of LigA and LigB from Leptospira interrogans serovar Copenhageni. Immunization of Golden Syrian hamsters with Lig fragments in Freund's adjuvant induced robust antibody responses against recombinant protein and native protein, as detected by ELISA and immunoblot, respectively. A single fragment, LigANI, which corresponds to the six carboxy-terminal Ig-like repeat domains of the LigA molecule, conferred immunoprotection against mortality (67-100%, P<0.05) in hamsters which received a lethal inoculum of L. interrogans serovar Copenhageni. However, immunization with this fragment did not confer sterilizing immunity. These findings indicate that the carboxy-terminal portion of LigA is an immunoprotective domain and may serve as a vaccine candidate for human and veterinary leptospirosis.
Novel hydrogen decrepitation behaviors of (La, Ce)-Fe-B strips
Jin, Jiaying; Bai, Guohua; Zhang, Yujing; Peng, Baixing; Liu, Yongsheng; Ma, Tianyu; Yan, Mi
2018-05-01
La and Ce substitution for Nd in the 2:14:1-type sintered magnet is of commercial interest to reduce the material cost and to balance the utilization of rare earth (RE) sources. As hydrogen decrepitation (HD) is widely utilized to prepare the magnetic powders during magnets fabrication, incorporating La and Ce into the Nd-Fe-B permanent magnets, however, may exert complex influences on the decrepitation behavior. In the present work, through a comparative study of the HD behaviors between the (La, Ce)-Fe-B strips and the conventional Nd-Fe-B ones, we find that similar to the Nd-Fe-B system, increasing hydrogen pressures from 2.5 to 5.5 MPa do not break the 2:14:1 tetragonal structure of (La, Ce)-Fe-B strips. The enhanced hydrogen absorption behaviors are observed with increasing pressure, which are still inferior to that of the Nd-Fe-B strips. This should be ascribed to the higher oxygen affinity of La and Ce than that of Nd, leading to the decreased amount of active RE-rich phase and limited hydrogen diffusion channel. As a result, the hydrogen absorption of 2:14:1 matrix phase is significantly suppressed, dramatically weakening the exothermic effect. This finding suggests that La and Ce with stable 2:14:1 tetragonal structure upon HD process are promising alternatives for Nd, despite that more precise oxygen control is necessary for the microstructure modification and magnetic performance enhancement of (La, Ce)-Fe-B sintered magnets.
Harvinaisten maametallien talteenotto NdFeB -magneeteista
Kangas, Sanna
2017-01-01
Tutkielman kirjallisessa osassa käsitellään yleisesti harvinaisia maametalleja, niiden ominaisuuksia, valmistusta, käyttökohteita ja kierrätystä lopputuotteista. Harvinaisten maametallien käyttökohteista keskitytään neodyymi-rauta-boori -magneetteihin (NdFeB -magneetit) ja niiden kierrätykseen. Tutkielmassa käydään läpi erilaiset harvinaisten maametallien hydrometallurgiset ja pyrometallurgiset talteenottomenetelmät. Tutkimusprojektissa pyrittiin kehittämään NdFeB -magneettien kierrätysme...
Recent development in bonded NdFeB magnets
International Nuclear Information System (INIS)
Ma, B.M.; Herchenroeder, J.W.; Smith, B.; Suda, M.; Brown, D.N.; Chen, Z.
2002-01-01
The magnetic properties of isotropic NdFeB powders used for bonded magnets are compared. The characteristics of two newly developed powders, namely MQP-13-9 and MQP-S-9-8 were compared with respect to existing powders. The advantages of spherical powders for injection molding were highlighted. Development targets for the 180 deg. C application and NdFeB nanocomposites were also discussed
Forward W + c, b-jet and Top Measurements with LHCb
INSPIRE-00258006
2015-01-01
Inclusive c and b-jet tagging algorithms have been developed to utilize the excellent secondary vertex reconstruction and resolution capabilities of the LHCb detector. The validation and performance of these tagging algorithms are reported using the full run 1 LHCb dataset at 7 and 8 TeV. Jet-tagging has been applied to muon+jet final states to measure both the W+c,b-jet charge asymmetries and the ratios of W+c,b-jet to W+jet and W+jet to Z+jet production. The forward top production cross-section is also measured using the muon+b-jet final. All results are found to be consistent with standard model predictions.
Cluster-based bulk metallic glass formation in Fe-Si-B-Nb alloy systems
Energy Technology Data Exchange (ETDEWEB)
Zhu, C L; Wang, Q; Li, F W; Li, Y H; Wang, Y M; Dong, C [State Key Laboratory of Materials Modification, Dalian University of Technology (DUT), Dalian 116024 (China); Zhang, W; Inoue, A, E-mail: dong@dlut.edu.c [Institute for Materials Research (IMR), Tohoku University, Katahira 2-1-1, Aoba-Ku, Sendai 980-8577 (Japan)
2009-01-01
Bulk metallic glass formations have been explored in Fe-B-Si-Nb alloy system using the so-called atomic cluster line approach in combination with minor alloying guideline. The atomic cluster line refers to a straight line linking binary cluster to the third element in a ternary system. The basic ternary compositions in Fe-B-Si system are determined by the inetersection points of two cluster lines, namely Fe-B cluster to Si and Fe-Si cluster to B, and then further alloyed with 3-5 at. % Nb for enhancing glass forming abilities. BMG rods with a diameter of 3 mm are formed under the case of minor Nb alloying the basic intersecting compositions of Fe{sub 8}B{sub 3}-Si with Fe{sub 12}Si-B and Fe{sub 8}B{sub 2}-Si with Fe{sub 9}Si-B. The BMGs also exhibit high Vickers hardness (H{sub v}) of 1130-1164 and high Young's modulous (E) of 170-180 GPa
International Nuclear Information System (INIS)
Guo, Jinxue; Jiang, Bin; Zhang, Xiao; Zhou, Xiaoyu; Hou, Wanguo
2013-01-01
Fe 2.25 W 0.75 O 4 /reduced graphene oxide (RGO) composites were prepared for application of novel bifunctional photocatalyst via simple one-pot hydrothermal method, employing graphene oxide (GO), Na 2 WO 4 , FeSO 4 and sodium dodecyl benzene sulfonate (SDBS) as the precursors. Transmission electron microscope (TEM) results indicate that the well-dispersed Fe 2.25 W 0.75 O 4 nanoparticles were deposited on the surface of RGO sheets homogeneously. Magnetic characterization reveals that Fe 2.25 W 0.75 O 4 and Fe 2.25 W 0.75 O 4 /RGO show ferromagnetic behaviors. So this novel bifunctional photocatalyst could achieve magnetic separation and collection with the aid of external magnet. The composites exhibit enhanced photocatalytic performance on degradation of methyl orange (MO) compared with pure Fe 2.25 W 0.75 O 4 under low-power ultraviolet light irradiation due to the introduction of RGO. Moreover, this hybrid catalyst possesses long-term excellent photocatalytic performance due to its good thermal stability. This bifunctional photocatalyst, which combines magnetic property and excellent photocatalytic activity, would be a perfect candidate in applications of catalytic elimination of environmental pollutants and other areas. - Graphical abstract: Magnetically recyclable Fe 2.25 W 0.75 O 4 /reduced graphene oxide nanocomposites with enhanced photocatalytic property Display Omitted - Highlights: ●Fe 2.25 W 0.75 O 4 growth, deposition and GO reduction occurred simultaneously. ●Composite possessed ferromagnetic and enhanced photocatalytic properties. ●Composite is utilized as a magnetically separable and high-efficient photocatalyst. ●Photocatalyst showed good photocatalytic and thermal stability during cyclic use
Thermal aging of melt-spun NdFeB magnetic powder in hydrogen
International Nuclear Information System (INIS)
Pinkerton, Frederick E.; Balogh, Michael P.; Ellison, Nicole; Foto, Aldo; Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P.
2016-01-01
High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity H ci of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H 2 gas. Expansion of the NdFeB crystal lattice in both ATF and H 2 identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets. - Highlights: • Injection molded NdFeB magnets age rapidly in automatic transmission fluid (ATF). • Coercivity loss is not due to direct chemical reaction between ATF and the powder. • Chemical reaction with the binder does not play a major role in aging. • Hydrogen dissociates from ATF and diffuses into Nd 2 Fe 14 B, reducing coercivity.
Thermal aging of melt-spun NdFeB magnetic powder in hydrogen
Energy Technology Data Exchange (ETDEWEB)
Pinkerton, Frederick E., E-mail: frederick.e.pinkerton@gm.com [Chemical and Materials Systems Laboratory, General Motors Research and Development Center, Warren, MI 48092 (United States); Balogh, Michael P.; Ellison, Nicole [Chemical and Materials Systems Laboratory, General Motors Research and Development Center, Warren, MI 48092 (United States); Foto, Aldo [Element Materials Technology Wixom, Inc (United States); Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P. [Powertrain Materials/Fluids/AMPPD Engineering and Labs, GFL VE/PT Materials Engineering, General Motors LLC, Pontiac, MI 48340 (United States)
2016-11-01
High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity H{sub ci} of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H{sub 2} gas. Expansion of the NdFeB crystal lattice in both ATF and H{sub 2} identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets. - Highlights: • Injection molded NdFeB magnets age rapidly in automatic transmission fluid (ATF). • Coercivity loss is not due to direct chemical reaction between ATF and the powder. • Chemical reaction with the binder does not play a major role in aging. • Hydrogen dissociates from ATF and diffuses into Nd{sub 2}Fe{sub 14}B, reducing coercivity.
Thermal aging of melt-spun NdFeB magnetic powder in hydrogen
Pinkerton, Frederick E.; Balogh, Michael P.; Ellison, Nicole; Foto, Aldo; Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P.
2016-11-01
High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity Hci of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H2 gas. Expansion of the NdFeB crystal lattice in both ATF and H2 identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets.
Corrosion of NdFeB permanent magnet materials
International Nuclear Information System (INIS)
Warren, G.W.; Gao, G.; Li, Q.
1991-01-01
NdFeB is an important class of new magnetic materials, however corrosion resistance is a serious concern and literature on the electrochemical behavior of NdFeB is scarce. This paper reports the results of an electrochemical investigation of the corrosion behavior of sintered NdFeB magnets obtained from three manufacturers. Linear polarization (cyclic voltammetry) experiments were conducted in aqueous solutions ranging in pH from 0.7 to 13.5. A limited degree of passivation was observed in all solutions which is believed to be due to the formation of a complex Fe-Nd oxide and/or hydroxide film. The presence of a small amount of chloride ion, 10 to 100 ppm, shows only a slight effect, but higher concentrations (1000 ppm) cause a total breakdown in passivity and a dramatic increase in anodic current. The cathodic potential sweep shows an abrupt and unusual oxidation process, giving rise to an oxidation peak not commonly seen. This peak may result from dissolution of the film or preferential attack of intergranular phases
Staphylococcus aureus Meticilina Resistente (MRSA e Infecções Nosocomiais
Directory of Open Access Journals (Sweden)
CRISTINA PAIVA SOUSA
2009-12-01
Full Text Available Um número crescente de cepas de Staphylococcus aureus meticilina resistente (MRSA apresentam resistência a múltiplos agentes antimicrobianos e são implicadas como causas de infecções hospitalares. S. aureus podem ser isolados de ambiente hospitalar e profissionais da saúde, revelando o risco de transmissão desses microrganismos pelo contato direto ou indireto com pacientes hospitalizados. Objetivou-se nesta revisão correlacionar este microrganismo com infecções hospitalares e avaliar as possíveis fontes de infecção, bem como enfatizar a importância do investimento em ações de educação em saúde que culminem em minimização de infecções hospitalares. Palavras-chave: Staphylococcus aureus meticilina resistente. Infecções nosocomiais.
Energy Technology Data Exchange (ETDEWEB)
Takeuchi, A., E-mail: takeuchi@imr.tohoku.ac.jp; Zhang, Y.; Takenaka, K.; Makino, A. [Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan)
2015-05-07
Fe-based Fe{sub 85}B{sub 15}, Fe{sub 84}B{sub 15}Cu{sub 1}, Fe{sub 82}Si{sub 2}B{sub 15}Cu{sub 1}, Fe{sub 85}Si{sub 2}B{sub 12}Cu{sub 1}, and Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} (NANOMET{sup ®}) alloys were experimental and computational analyzed to clarify the features of NANOMET that exhibits high saturation magnetic flux density (B{sub s}) nearly 1.9 T and low core loss than conventional nanocrystalline soft magnetic alloys. The X-ray diffraction analysis for ribbon specimens produced experimentally by melt spinning from melts revealed that the samples were almost formed into an amorphous single phase. Then, the as-quenched samples were analyzed with differential scanning calorimeter (DSC) experimentally for exothermic enthalpies of the primary and secondary crystallizations (ΔH{sub x1} and ΔH{sub x2}) and their crystallization temperatures (T{sub x1} and T{sub x2}), respectively. The ratio ΔH{sub x1}/ΔH{sub x2} measured by DSC experimentally tended to be extremely high for the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy, and this tendency was reproduced by the analysis with commercial software, Thermo-Calc, with database for Fe-based alloys, TCFE7 for Gibbs free energy (G) assessments. The calculations exhibit that a volume fraction (V{sub f}) of α-Fe tends to increase from 0.56 for the Fe{sub 85}B{sub 15} to 0.75 for the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy. The computational analysis of the alloys for G of α-Fe and amorphous phases (G{sub α-Fe} and G{sub amor}) shows that a relationship G{sub α-Fe} ∼ G{sub amor} holds for the Fe{sub 85}Si{sub 2}B{sub 12}Cu{sub 1}, whereas G{sub α-Fe} < G{sub amor} for the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy at T{sub x1} and that an extremely high V{sub f} = 0.75 was achieved for the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy by including 2.8 at. % Si and 4.5 at. % P into α-Fe. These computational results indicate that the Fe{sub 85}Si{sub 2}B
Directory of Open Access Journals (Sweden)
Manju Soman
2018-04-01
Full Text Available Aim: This study aims at cloning, sequencing, and phylogenetic analysis of a partial CDS of ligA gene in pET-32a - Escherichia coli DH5α system, with the objective of identifying the conserved nature of the ligA gene in the genus Leptospira. Materials and Methods: A partial CDS (nucleotide 1873 to nucleotide 3363 of the ligA gene was amplified from genomic DNA of Leptospira interrogans serovar Canicola by polymerase chain reaction (PCR. The PCR-amplified DNA was cloned into pET-32a vector and transformed into competent E. coli DH5α bacterial cells. The partial ligA gene insert was sequenced and the nucleotide sequences obtained were aligned with the published ligA gene sequences of other Leptospira serovars, using nucleotide BLAST, NCBI. Phylogenetic analysis of the gene sequence was done by maximum likelihood method using Mega 6.06 software. Results: The PCR could amplify the 1491 nucleotide sequence spanning from nucleotide 1873 to nucleotide 3363 of the ligA gene and the partial ligA gene could be successfully cloned in E. coli DH5α cells. The nucleotide sequence when analyzed for homology with the reported gene sequences of other Leptospira serovars was found to have 100% homology to the 1910 bp to 3320 bp sequence of ligA gene of L. interrogans strain Kito serogroup Canicola. The predicted protein consisted of 470 aminoacids. Phylogenetic analysis revealed that the ligA gene was conserved in L. interrogans species. Conclusion: The partial ligA gene could be successfully cloned and sequenced from E. coli DH5α cells. The sequence showed 100% homology to the published ligA gene sequences. The phylogenetic analysis revealed the conserved nature of the ligA gene. Further studies on the expression and immunogenicity of the partial LigA protein need to be carried out to determine its competence as a subunit vaccine candidate.
Aaij, Roel; Adinolfi, Marco; Ajaltouni, Ziad; Akar, Simon; Albrecht, Johannes; Alessio, Federico; Alexander, Michael; Ali, Suvayu; Alkhazov, Georgy; Alvarez Cartelle, Paula; Alves Jr, Antonio Augusto; Amato, Sandra; Amerio, Silvia; Amhis, Yasmine; An, Liupan; Anderlini, Lucio; Andreassi, Guido; Andreotti, Mirco; Andrews, Jason; Appleby, Robert; Archilli, Flavio; d'Argent, Philippe; Arnau Romeu, Joan; Artamonov, Alexander; Artuso, Marina; Aslanides, Elie; Auriemma, Giulio; Baalouch, Marouen; Babuschkin, Igor; Bachmann, Sebastian; Back, John; Badalov, Alexey; Baesso, Clarissa; Baker, Sophie; Baldini, Wander; Barlow, Roger; Barschel, Colin; Barsuk, Sergey; Barter, William; Baszczyk, Mateusz; Batozskaya, Varvara; Batsukh, Baasansuren; Battista, Vincenzo; Bay, Aurelio; Beaucourt, Leo; Beddow, John; Bedeschi, Franco; Bediaga, Ignacio; Bel, Lennaert; Bellee, Violaine; Belloli, Nicoletta; Belous, Konstantin; Belyaev, Ivan; Ben-Haim, Eli; Bencivenni, Giovanni; Benson, Sean; Benton, Jack; Berezhnoy, Alexander; Bernet, Roland; Bertolin, Alessandro; Betti, Federico; Bettler, Marc-Olivier; van Beuzekom, Martinus; Bezshyiko, Iaroslava; Bifani, Simone; Billoir, Pierre; Bird, Thomas; Birnkraut, Alex; Bitadze, Alexander; Bizzeti, Andrea; Blake, Thomas; Blanc, Frederic; Blouw, Johan; Blusk, Steven; Bocci, Valerio; Boettcher, Thomas; Bondar, Alexander; Bondar, Nikolay; Bonivento, Walter; Bordyuzhin, Igor; Borgheresi, Alessio; Borghi, Silvia; Borisyak, Maxim; Borsato, Martino; Bossu, Francesco; Boubdir, Meriem; Bowcock, Themistocles; Bowen, Espen Eie; Bozzi, Concezio; Braun, Svende; Britsch, Markward; Britton, Thomas; Brodzicka, Jolanta; Buchanan, Emma; Burr, Christopher; Bursche, Albert; Buytaert, Jan; Cadeddu, Sandro; Calabrese, Roberto; Calvi, Marta; Calvo Gomez, Miriam; Camboni, Alessandro; Campana, Pierluigi; Campora Perez, Daniel; Campora Perez, Daniel Hugo; Capriotti, Lorenzo; Carbone, Angelo; Carboni, Giovanni; Cardinale, Roberta; Cardini, Alessandro; Carniti, Paolo; Carson, Laurence; Carvalho Akiba, Kazuyoshi; Casse, Gianluigi; Cassina, Lorenzo; Castillo Garcia, Lucia; Cattaneo, Marco; Cauet, Christophe; Cavallero, Giovanni; Cenci, Riccardo; Charles, Matthew; Charpentier, Philippe; Chatzikonstantinidis, Georgios; Chefdeville, Maximilien; Chen, Shanzhen; Cheung, Shu-Faye; Chobanova, Veronika; Chrzaszcz, Marcin; Cid Vidal, Xabier; Ciezarek, Gregory; Clarke, Peter; Clemencic, Marco; Cliff, Harry; Closier, Joel; Coco, Victor; Cogan, Julien; Cogneras, Eric; Cogoni, Violetta; Cojocariu, Lucian; Collazuol, Gianmaria; Collins, Paula; Comerma-Montells, Albert; Contu, Andrea; Cook, Andrew; Coombs, George; Coquereau, Samuel; Corti, Gloria; Corvo, Marco; Costa Sobral, Cayo Mar; Couturier, Benjamin; Cowan, Greig; Craik, Daniel Charles; Crocombe, Andrew; Cruz Torres, Melissa Maria; Cunliffe, Samuel; Currie, Robert; D'Ambrosio, Carmelo; Da Cunha Marinho, Franciole; Dall'Occo, Elena; Dalseno, Jeremy; David, Pieter; Davis, Adam; De Aguiar Francisco, Oscar; De Bruyn, Kristof; De Capua, Stefano; De Cian, Michel; De Miranda, Jussara; De Paula, Leandro; De Serio, Marilisa; De Simone, Patrizia; Dean, Cameron Thomas; Decamp, Daniel; Deckenhoff, Mirko; Del Buono, Luigi; Demmer, Moritz; Dendek, Adam; Derkach, Denis; Deschamps, Olivier; Dettori, Francesco; Dey, Biplab; Di Canto, Angelo; Dijkstra, Hans; Dordei, Francesca; Dorigo, Mirco; Dosil Suárez, Alvaro; Dovbnya, Anatoliy; Dreimanis, Karlis; Dufour, Laurent; Dujany, Giulio; Dungs, Kevin; Durante, Paolo; Dzhelyadin, Rustem; Dziurda, Agnieszka; Dzyuba, Alexey; Déléage, Nicolas; Easo, Sajan; Ebert, Marcus; Egede, Ulrik; Egorychev, Victor; Eidelman, Semen; Eisenhardt, Stephan; Eitschberger, Ulrich; Ekelhof, Robert; Eklund, Lars; Elsasser, Christian; Ely, Scott; Esen, Sevda; Evans, Hannah Mary; Evans, Timothy; Falabella, Antonio; Farley, Nathanael; Farry, Stephen; Fay, Robert; Fazzini, Davide; Ferguson, Dianne; Fernandez Prieto, Antonio; Ferrari, Fabio; Ferreira Rodrigues, Fernando; Ferro-Luzzi, Massimiliano; Filippov, Sergey; Fini, Rosa Anna; Fiore, Marco; Fiorini, Massimiliano; Firlej, Miroslaw; Fitzpatrick, Conor; Fiutowski, Tomasz; Fleuret, Frederic; Fohl, Klaus; Fontana, Marianna; Fontanelli, Flavio; Forshaw, Dean Charles; Forty, Roger; Franco Lima, Vinicius; Frank, Markus; Frei, Christoph; Fu, Jinlin; Furfaro, Emiliano; Färber, Christian; Gallas Torreira, Abraham; Galli, Domenico; Gallorini, Stefano; Gambetta, Silvia; Gandelman, Miriam; Gandini, Paolo; Gao, Yuanning; Garcia Martin, Luis Miguel; García Pardiñas, Julián; Garra Tico, Jordi; Garrido, Lluis; Garsed, Philip John; Gascon, David; Gaspar, Clara; Gavardi, Laura; Gazzoni, Giulio; Gerick, David; Gersabeck, Evelina; Gersabeck, Marco; Gershon, Timothy; Ghez, Philippe; Gianì, Sebastiana; Gibson, Valerie; Girard, Olivier Göran; Giubega, Lavinia-Helena; Gizdov, Konstantin; Gligorov, V.V.; Golubkov, Dmitry; Golutvin, Andrey; Gomes, Alvaro; Gorelov, Igor Vladimirovich; Gotti, Claudio; Grabalosa Gándara, Marc; Graciani Diaz, Ricardo; Granado Cardoso, Luis Alberto; Graugés, Eugeni; Graverini, Elena; Graziani, Giacomo; Grecu, Alexandru; Griffith, Peter; Grillo, Lucia; Gruberg Cazon, Barak Raimond; Grünberg, Oliver; Gushchin, Evgeny; Guz, Yury; Gys, Thierry; Göbel, Carla; Hadavizadeh, Thomas; Hadjivasiliou, Christos; Haefeli, Guido; Haen, Christophe; Haines, Susan; Hall, Samuel; Hamilton, Brian; Han, Xiaoxue; Hansmann-Menzemer, Stephanie; Harnew, Neville; Harnew, Samuel; Harrison, Jonathan; Hatch, Mark; He, Jibo; Head, Timothy; Heister, Arno; Hennessy, Karol; Henrard, Pierre; Henry, Louis; Hernando Morata, Jose Angel; van Herwijnen, Eric; Heß, Miriam; Hicheur, Adlène; Hill, Donal; Hombach, Christoph; Hopchev, P H; Hulsbergen, Wouter; Humair, Thibaud; Hushchyn, Mikhail; Hussain, Nazim; Hutchcroft, David; Idzik, Marek; Ilten, Philip; Jacobsson, Richard; Jaeger, Andreas; Jalocha, Pawel; Jans, Eddy; Jawahery, Abolhassan; Jiang, Feng; John, Malcolm; Johnson, Daniel; Jones, Christopher; Joram, Christian; Jost, Beat; Jurik, Nathan; Kandybei, Sergii; Kanso, Walaa; Karacson, Matthias; Kariuki, James Mwangi; Karodia, Sarah; Kecke, Matthieu; Kelsey, Matthew; Kenyon, Ian; Kenzie, Matthew; Ketel, Tjeerd; Khairullin, Egor; Khanji, Basem; Khurewathanakul, Chitsanu; Kirn, Thomas; Klaver, Suzanne; Klimaszewski, Konrad; Koliiev, Serhii; Kolpin, Michael; Komarov, Ilya; Koopman, Rose; Koppenburg, Patrick; Kosmyntseva, Alena; Kozachuk, Anastasiia; Kozeiha, Mohamad; Kravchuk, Leonid; Kreplin, Katharina; Kreps, Michal; Krokovny, Pavel; Kruse, Florian; Krzemien, Wojciech; Kucewicz, Wojciech; Kucharczyk, Marcin; Kudryavtsev, Vasily; Kuonen, Axel Kevin; Kurek, Krzysztof; Kvaratskheliya, Tengiz; Lacarrere, Daniel; Lafferty, George; Lai, Adriano; Lambert, Dean; Lanfranchi, Gaia; Langenbruch, Christoph; Latham, Thomas; Lazzeroni, Cristina; Le Gac, Renaud; van Leerdam, Jeroen; Lees, Jean-Pierre; Leflat, Alexander; Lefrançois, Jacques; Lefèvre, Regis; Lemaitre, Florian; Lemos Cid, Edgar; Leroy, Olivier; Lesiak, Tadeusz; Leverington, Blake; Li, Yiming; Likhomanenko, Tatiana; Lindner, Rolf; Linn, Christian; Lionetto, Federica; Liu, Bo; Liu, Xuesong; Loh, David; Longstaff, Iain; Lopes, Jose; Lucchesi, Donatella; Lucio Martinez, Miriam; Luo, Haofei; Lupato, Anna; Luppi, Eleonora; Lupton, Oliver; Lusiani, Alberto; Lyu, Xiao-Rui; Machefert, Frederic; Maciuc, Florin; Maev, Oleg; Maguire, Kevin; Malde, Sneha; Malinin, Alexander; Maltsev, Timofei; Manca, Giulia; Mancinelli, Giampiero; Manning, Peter Michael; Maratas, Jan; Marchand, Jean François; Marconi, Umberto; Marin Benito, Carla; Marino, Pietro; Marks, Jörg; Martellotti, Giuseppe; Martin, Morgan; Martinelli, Maurizio; Martinez Santos, Diego; Martinez Vidal, Fernando; Martins Tostes, Danielle; Massacrier, Laure Marie; Massafferri, André; Matev, Rosen; Mathad, Abhijit; Mathe, Zoltan; Matteuzzi, Clara; Mauri, Andrea; Maurin, Brice; Mazurov, Alexander; McCann, Michael; McCarthy, James; McNab, Andrew; McNulty, Ronan; Meadows, Brian; Meier, Frank; Meissner, Marco; Melnychuk, Dmytro; Merk, Marcel; Merli, Andrea; Michielin, Emanuele; Milanes, Diego Alejandro; Minard, Marie-Noelle; Mitzel, Dominik Stefan; Mogini, Andrea; Molina Rodriguez, Josue; Monroy, Ignacio Alberto; Monteil, Stephane; Morandin, Mauro; Morawski, Piotr; Mordà, Alessandro; Morello, Michael Joseph; Moron, Jakub; Morris, Adam Benjamin; Mountain, Raymond; Muheim, Franz; Mulder, Mick; Mussini, Manuel; Müller, Dominik; Müller, Janine; Müller, Katharina; Müller, Vanessa; Naik, Paras; Nakada, Tatsuya; Nandakumar, Raja; Nandi, Anita; Nasteva, Irina; Needham, Matthew; Neri, Nicola; Neubert, Sebastian; Neufeld, Niko; Neuner, Max; Nguyen, Anh Duc; Nguyen, Thi Dung; Nguyen-Mau, Chung; Nieswand, Simon; Niet, Ramon; Nikitin, Nikolay; Nikodem, Thomas; Novoselov, Alexey; O'Hanlon, Daniel Patrick; Oblakowska-Mucha, Agnieszka; Obraztsov, Vladimir; Ogilvy, Stephen; Oldeman, Rudolf; Onderwater, Gerco; Otalora Goicochea, Juan Martin; Otto, Adam; Owen, Patrick; Oyanguren, Maria Aranzazu; Pais, Preema Rennee; Palano, Antimo; Palombo, Fernando; Palutan, Matteo; Panman, Jacob; Papanestis, Antonios; Pappagallo, Marco; Pappalardo, Luciano; Parker, William; Parkes, Christopher; Passaleva, Giovanni; Pastore, Alessandra; Patel, Girish; Patel, Mitesh; Patrignani, Claudia; Pearce, Alex; Pellegrino, Antonio; Penso, Gianni; Pepe Altarelli, Monica; Perazzini, Stefano; Perret, Pascal; Pescatore, Luca; Petridis, Konstantinos; Petrolini, Alessandro; Petrov, Aleksandr; Petruzzo, Marco; Picatoste Olloqui, Eduardo; Pietrzyk, Boleslaw; Pikies, Malgorzata; Pinci, Davide; Pistone, Alessandro; Piucci, Alessio; Playfer, Stephen; Plo Casasus, Maximo; Poikela, Tuomas; Polci, Francesco; Poluektov, Anton; Polyakov, Ivan; Polycarpo, Erica; Pomery, Gabriela Johanna; Popov, Alexander; Popov, Dmitry; Popovici, Bogdan; Poslavskii, Stanislav; Potterat, Cédric; Price, Eugenia; Price, Joseph David; Prisciandaro, Jessica; Pritchard, Adrian; Prouve, Claire; Pugatch, Valery; Puig Navarro, Albert; Punzi, Giovanni; Qian, Wenbin; Quagliani, Renato; Rachwal, Bartolomiej; Rademacker, Jonas; Rama, Matteo; Ramos Pernas, Miguel; Rangel, Murilo; Raniuk, Iurii; Raven, Gerhard; Redi, Federico; Reichert, Stefanie; dos Reis, Alberto; Remon Alepuz, Clara; Renaudin, Victor; Ricciardi, Stefania; Richards, Sophie; Rihl, Mariana; Rinnert, Kurt; Rives Molina, Vicente; Robbe, Patrick; Rodrigues, Ana Barbara; Rodrigues, Eduardo; Rodriguez Lopez, Jairo Alexis; Rodriguez Perez, Pablo; Rogozhnikov, Alexey; Roiser, Stefan; Rollings, Alexandra Paige; Romanovskiy, Vladimir; Romero Vidal, Antonio; Ronayne, John William; Rotondo, Marcello; Rudolph, Matthew Scott; Ruf, Thomas; Ruiz Valls, Pablo; Saborido Silva, Juan Jose; Sadykhov, Elnur; Sagidova, Naylya; Saitta, Biagio; Salustino Guimaraes, Valdir; Sanchez Mayordomo, Carlos; Sanmartin Sedes, Brais; Santacesaria, Roberta; Santamarina Rios, Cibran; Santimaria, Marco; Santovetti, Emanuele; Sarti, Alessio; Satriano, Celestina; Satta, Alessia; Saunders, Daniel Martin; Savrina, Darya; Schael, Stefan; Schellenberg, Margarete; Schiller, Manuel; Schindler, Heinrich; Schlupp, Maximilian; Schmelling, Michael; Schmelzer, Timon; Schmidt, Burkhard; Schneider, Olivier; Schopper, Andreas; Schubert, Konstantin; Schubiger, Maxime; Schune, Marie Helene; Schwemmer, Rainer; Sciascia, Barbara; Sciubba, Adalberto; Semennikov, Alexander; Sergi, Antonino; Serra, Nicola; Serrano, Justine; Sestini, Lorenzo; Seyfert, Paul; Shapkin, Mikhail; Shapoval, Illya; Shcheglov, Yury; Shears, Tara; Shekhtman, Lev; Shevchenko, Vladimir; Shires, Alexander; Siddi, Benedetto Gianluca; Silva Coutinho, Rafael; Silva de Oliveira, Luiz Gustavo; Simi, Gabriele; Simone, Saverio; Sirendi, Marek; Skidmore, Nicola; Skwarnicki, Tomasz; Smith, Eluned; Smith, Iwan Thomas; Smith, Jackson; Smith, Mark; Snoek, Hella; Sokoloff, Michael; Soler, Paul; Souza De Paula, Bruno; Spaan, Bernhard; Spradlin, Patrick; Sridharan, Srikanth; Stagni, Federico; Stahl, Marian; Stahl, Sascha; Stefko, Pavol; Stefkova, Slavorima; Steinkamp, Olaf; Stemmle, Simon; Stenyakin, Oleg; Stevenson, Scott; Stoica, Sabin; Stone, Sheldon; Storaci, Barbara; Stracka, Simone; Straticiuc, Mihai; Straumann, Ulrich; Sun, Liang; Sutcliffe, William; Swientek, Krzysztof; Syropoulos, Vasileios; Szczekowski, Marek; Szumlak, Tomasz; T'Jampens, Stephane; Tayduganov, Andrey; Tekampe, Tobias; Tellarini, Giulia; Teubert, Frederic; Thomas, Eric; van Tilburg, Jeroen; Tilley, Matthew James; Tisserand, Vincent; Tobin, Mark; Tolk, Siim; Tomassetti, Luca; Tonelli, Diego; Topp-Joergensen, Stig; Toriello, Francis; Tournefier, Edwige; Tourneur, Stephane; Trabelsi, Karim; Traill, Murdo; Tran, Minh Tâm; Tresch, Marco; Trisovic, Ana; Tsaregorodtsev, Andrei; Tsopelas, Panagiotis; Tully, Alison; Tuning, Niels; Ukleja, Artur; Ustyuzhanin, Andrey; Uwer, Ulrich; Vacca, Claudia; Vagnoni, Vincenzo; Valassi, Andrea; Valat, Sebastien; Valenti, Giovanni; Vallier, Alexis; Vazquez Gomez, Ricardo; Vazquez Regueiro, Pablo; Vecchi, Stefania; van Veghel, Maarten; Velthuis, Jaap; Veltri, Michele; Veneziano, Giovanni; Venkateswaran, Aravindhan; Vernet, Maxime; Vesterinen, Mika; Viaud, Benoit; Vieira, Daniel; Vieites Diaz, Maria; Vilasis-Cardona, Xavier; Volkov, Vladimir; Vollhardt, Achim; Voneki, Balazs; Vorobyev, Alexey; Vorobyev, Vitaly; Voß, Christian; de Vries, Jacco; Vázquez Sierra, Carlos; Waldi, Roland; Wallace, Charlotte; Wallace, Ronan; Walsh, John; Wang, Jianchun; Ward, David; Wark, Heather Mckenzie; Watson, Nigel; Websdale, David; Weiden, Andreas; Whitehead, Mark; Wicht, Jean; Wilkinson, Guy; Wilkinson, Michael; Williams, Mark Richard James; Williams, Matthew; Williams, Mike; Williams, Timothy; Wilson, Fergus; Wimberley, Jack; Wishahi, Julian; Wislicki, Wojciech; Witek, Mariusz; Wormser, Guy; Wotton, Stephen; Wraight, Kenneth; Wright, Simon; Wyllie, Kenneth; Xie, Yuehong; Xing, Zhou; Xu, Zhirui; Yang, Zhenwei; Yin, Hang; Yu, Jiesheng; Yuan, Xuhao; Yushchenko, Oleg; Zarebski, Kristian Alexander; Zavertyaev, Mikhail; Zhang, Liming; Zhang, Yanxi; Zhang, Yu; Zhelezov, Alexey; Zheng, Yangheng; Zhokhov, Anatoly; Zhu, Xianglei; Zhukov, Valery; Zucchelli, Stefano
2017-04-10
The production of $t\\overline{t}$, $W+b\\overline{b}$ and $W+c\\overline{c}$ is studied in the forward region of proton-proton collisions collected at a centre-of-mass energy of 8 TeV by the LHCb experiment, corresponding to an integrated luminosity of 1.98 $\\pm$ 0.02 $\\mbox{fb}^{-1}$. The $W$ bosons are reconstructed in the decays $W\\rightarrow\\ell\
Directory of Open Access Journals (Sweden)
A. Corso
2009-03-01
Full Text Available During the period 1993-2001, a total of 1,499 pneumococci isolates were recovered through the Argentinean surveillance of Streptococcus pneumoniae causing invasive disease in children under 6 years of age, 3.5% of which were erythromycin resistant. Among the 50 erythromycin-resistant strains available, 58% (n=29 harbored mefA/E genes (15 mefA, 30%; and 14 mefE, 28%, 34% (n=17 ermB, and 6% (n=3 both mefA/E plus ermB genes, while one isolate was negative for all the acquired genes studied. The England14-9 (42%, Poland6B-20 (20% and Spain9v-3 (16% clones were responsible for the emergence of pneumococcal macrolide resistance in pediatric population from Argentina.En el marco del programa de vigilancia regional SIREVA, se analizaron 1499 aislamientos de Streptococcus pneumoniae causantes de enfermedad invasiva en menores de 6 años, recuperados entre 1993 y 2001. Se detectó un 3,5% de resistencia a eritromicina. De los 50 aislamientos resistentes a eritromicina que pudieron ser estudiados, el 58% (n=29 tenían los genes mefA/E (15 mefA, 30% y 14 mefE, 28%, el 34% (n=17 el gen ermB y el 6% (n=3 la combinación de genes mefA/E y ermB. Sólo un aislamiento fue negativo para todos los genes analizados. Los clones internacionales England14-9, Poland6B-20 y Spain9v-3 representaron el 78% del total de aislamientos resistentes (42, 20 y 16%, respectivamente y se consideraron los responsables de la emergencia de la resistencia a macrólidos entre los neumococos que afectan a la población pediátrica de Argentina.
Higher-order radiative corrections for b b ¯→H-W+
Kidonakis, Nikolaos
2018-02-01
I present higher-order radiative corrections from collinear and soft-gluon emission for the associated production of a charged Higgs boson with a W boson. The calculation uses expressions from resummation at next-to-leading-logarithm accuracy. From the resummed cross section I derive analytical formulas at approximate next-to-next-to-leading order and next-to-next-to-next-to-leading order. Total cross sections are presented for the process b b ¯→H-W+ at various LHC energies. The transverse momentum and rapidity distributions of the charged Higgs boson are also calculated.
International Nuclear Information System (INIS)
Matsuura, Yutaka; Hoshijima, Jun; Ishii, Rintaro
2013-01-01
It was found that the coercive force of NdFeB sintered magnets decreases as the Nd 2 Fe 14 B grain alignment improves. Because of this phenomenon, studies looked at the relation between this alignment and the coercive force decrease ratio. In experiments, it was expected that the coercive force of perfectly aligned magnet reached 0.7 of coercive force in istotropically aligned magnet. When it is postulated that the coercive force is determined by the Stoner–Wohlfarth model, coercive force increases as the alignment improves and it becomes difficult to explain our experimental data. On the other hand, when the coercive force is determined by magnetic domain wall motion, the coercive force decreases as the alignment improves and the coercive force of the perfectly aligned magnet reaches 1/√(2) of the isotropically aligned magnet. This tendency and value was very close to our data. It strongly suggests that the coercive force of NdFeB sintered magnets is determined by the domain wall motion. - Highlights: ► Coercive force of NdFeB sintered magnets decreases as grains alignment improves. ► Coercive force decrease ratio reaches −30% at the perfect aligned magnet. ►These experimental results are different from the Stoner–Wohlfarth model. ► The magnetic domain wall motion could explain this coercive force decrease ratio
Superconducting state in (W, Ta)5SiB2
Fukuma, M.; Kawashima, K.; Akimitsu, J.
We characterize the superconducting state in a boro-silicide (W, Ta)5SiB2, with Tc of 6.5 K by means of magnetization, electrical resistivity, and specific heat measurements. As x increased, the transition temperature Tc abruptly enhances from 5.8 to 6.5 K. The magnetization versus magnetic field (M-H) curve indicated that (W, Ta)5SiB2 was a conventional type-II superconductor. The estimated lower critical field Hc1(0) and upper critical field Hc2(T) are about 121 Oe and 14.7 kOe, respectively. The penetration depth λ(0) and coherence length ξ(0) are calculated to be approximately 369 and 14.9 nm, respectively, using Ginzburg-Landau (GL) equations. Specific heat data shows the superconductivity in W4.5Ta0.5SiB2 belongs to a week-coupling BCS superconductor. Finally, we discuss the increasing of Tc in of (W, Ta)5SiB2 system.
Coercivity and nanostructure of melt-spun Ti-Fe-Co-B-based alloys
Directory of Open Access Journals (Sweden)
W. Y. Zhang
2016-05-01
Full Text Available Nanocrystalline Ti-Fe-Co-B-based alloys, prepared by melt spinning and subsequent annealing, have been characterized structurally and magnetically. X-ray diffraction and thermomagnetic measurements show that the ribbons consist of tetragonal Ti3(Fe,Co5B2, FeCo-rich bcc, and NiAl-rich L21 phases; Ti3(Fe,Co5B2, is a new substitutional alloy series whose end members Ti3Co5B2 and Ti3Fe5B2 have never been investigated magnetically and may not even exist, respectively. Two compositions are considered, namely Ti11+xFe37.5-0.5xCo37.5−0.5xB14 (x = 0, 4 and alnico-like Ti11Fe26Co26Ni10Al11Cu2B14, the latter also containing an L21-type alloy. The volume fraction of the Ti3(Fe,Co5B2 phase increases with x, which leads to a coercivity increase from 221 Oe for x = 0 to 452 Oe for x = 4. Since the grains are nearly equiaxed, there is little or no shape anisotropy, and the coercivity is largely due to the magnetocrystalline anisotropy of the tetragonal Ti3(Fe,Co5B2 phase. The alloy containing Ni, Al, and Cu exhibits a magnetization of 10.6 kG and a remanence ratio of 0.59. Our results indicate that magnetocrystalline anisotropy can be introduced in alnico-like magnets, adding to shape anisotropy that may be induced by field annealing.
Metamagnetic behaviour of La1-xGdxFe12B6 compounds
International Nuclear Information System (INIS)
Li, Q.A.; Groot, C.H. de; Boer, F.R. de; Buschow, K.H.J.
1997-01-01
The magnetic properties of compounds of the type La 1-x Gd x Fe 12 B 6 have been studied in high magnetic fields at 4.2 K. LaFe 12 B 6 is a compound with Fe moments close to magnetic instability and values not larger than about 0.5 μ B . Substitution of Gd for part of the La and application of high magnetic fields enhance the Fe moments to values in excess of 2 μ B . The high-moment state in LaFe 12 B 6 is reached via a metamagnetic transition. This first-order transition is associated with an extremely large hysteresis of nearly 7 T at 4.2 K. (orig.)
Crystallization of amorphous Fe78Si9B13 alloy
International Nuclear Information System (INIS)
Jakubczyk, E; Krajczyk, A; Jakubczyk, M
2007-01-01
The crystallization process of Fe 78 Si 9 B 13 metallic glass was investigated by DSC, X-ray diffraction, electrical resistivity, Hall effect and TEM methods. The investigations proved two-stages crystallization. By means of non-isothermal DSC experiments the activation energy and the Avrami exponent were determined for both stages. The created phases: α-Fe(Si) and (Fe,Si) 2 B were identified on the basis of X-ray and TEM investigations. However, TEM observations showed also a little amount of the FeB 49 phase as well as some rest of the amorphous phase. The electrical and Hall resistivities decrease abruptly after the creation of the phases out of the amorphous matrix
Nakano, M.; Kondo, H.; Yamashita, A.; Yanai, T.; Itakura, M.; Fukunaga, H.
2018-05-01
PLD (Pulsed Laser Deposition) method with high laser energy density (LED) above 10 J/cm2 followed by a flash annealing enabled us to obtain isotropic nano-composite thick-film magnets with (BH)max ≧ 80 kJ/m3 on polycrystalline Ta substrates. We also have demonstrated that a dispersed structure composed of α-Fe together with Nd2Fe14B phases with the average grain diameter of approximately 20 nm could be formed on the Ta substrates. In this study, we tried to enhance the (BH)max value by controlling the microstructure due to the usage of different metal based substrates with each high melting point such as Ti, Nb, and W. Although it was difficult to vary the microstructure and to improve the magnetic properties of the films deposited on the substrates, we confirmed that isotropic thick-film magnets with (BH)max ≧ 80 kJ/m3 based on the nano-dispersed α-Fe and Nd2Fe14B phases could be obtained on various metal substrates with totally different polycrystalline structure. On the other hand, the use of a glass substrate lead to the deterioration of magnetic properties of a film prepared using the same preparation process.
Structural Investigation of Rapidly Quenched FeCoPtB Alloys
International Nuclear Information System (INIS)
Grabias, A.; Kopcewicz, M.; Latuch, J.; Oleszak, D.
2011-01-01
Two sets of Fe 52-x Co x Pt 28 B 20 (x = 0-26 at.%) and Fe 60-x Co x Pt 25 B 15 (x = 0-40 at.%) alloys were prepared in the form of ribbons by the rapid quenching technique. Structure of the samples was characterized by Moessbauer spectroscopy and X-ray diffraction. In the as-quenched alloys the amorphous phase coexisted with the fcc-(Fe,Co)Pt disordered solid solution. Differential scanning calorimetry measurements performed in the range 50-720 ± C revealed one or two exothermal peaks. The magnetically hard ordered L1 0 (Fe,Co)Pt and magnetically soft (Fe,Co) 2 B nanocrystalline phases were formed due to thermal treatment of the alloys. The influence of Co content on the structure of the as-quenched and heated alloys was studied. (authors)
The temperature dependence of magnetic anisotropy of Nd-Fe-B thin films
Sato, Takuya; Hashimoto, Ryuji; Tanaka, Yoshitomo; Suzuki, Kenichi; Enokido, Yasushi; Choi, Kyung-Ku; Suzuki, Takao
2018-05-01
The magnetic properties of Nd-Fe-B thin films with the three different compositions (#1: Nd12.6Fe81.5B5.9, #2: Nd14.6Fe78.1B7.4 and #3: Nd22.6Fe66.2B11.2) are discussed. With increasing Nd content, the c-axis orientation along the film normal is enhanced. It is found that sample #2 possesses the saturation magnetization Ms very close to that for Nd2Fe14B over a temperature range from 100 to about 300K. The magnetic anisotropy constant Ku2 for sample #2 is the highest among those samples, but smaller by about 20%, as compared to that for Nd2Fe14B. It is of interest to note that the temperature TR at which Ku1 changes its sign is lower by about 30K as compared to that previously reported for Nd2Fe14B. The reason for this discrepancy is not clear, but could be due to the presence of the minority phases of Nd-rich compounds and also a possible contribution of the magneto-elastic effect to the net magnetic anisotropy.
Chen, Shaohai; Zhou, Jing; Lin, Weinan; Yu, Jihang; Guo, Rui; Poh, Francis; Shum, Danny; Chen, Jingsheng
2018-02-01
The thermal tolerance and perpendicular magnetic anisotropy (PMA) of ferromagnetic alloy Co40Fe40C20 in the structure MgO/CoFeC/Pt (or Ta) were investigated and compared with the commonly used CoFeB alloy. It is found that the PMA of CoFeC with {{K}i,CoFeC}=2.21 erg c{{m}-2} , which is 59% higher than that of CoFeB, can be obtained after proper post-annealing treatment. Furthermore, CoFeC alloy provides better thermal tolerance to temperature of 400 °C than CoFeB. The studies on ferromagnetic resonance show that the intrinsic damping constant α in of Co40Fe40C20 alloy is 0.0047, which is similar to the reported value of 0.004 for Co40Fe40B20 alloy. The comprehensive comparisons indicate that CoFeC alloy is a promising candidate for the application of the integration of spin torque transfer magnetic random access memory with complementary metal-oxide semiconductor processes.
Magnetic viscosity and texture in NdFeB magnets
International Nuclear Information System (INIS)
Martinez, J.C.; Missell, F.P.
1988-01-01
The dependence of the magnetic viscosity on texture can be used to study a model recently proposed by Givord and co-workers to describe the angular dependence of the coercive field in NdFeB magnets. We have measured the magnetic viscosity parameter S/sub v/ for samples of Magnequench (MQ) II and III as a function of magnetic field H and temperature T above room temperature. Near room temperature, S/sub v/ for MQ II is smaller than for MQ III, while for temperatures above ∼70 0 C, the opposite behavior is observed. This temperature dependence is discussed and compared with that observed in sintered NdFeB and NdDyFeB magnets
International Nuclear Information System (INIS)
Matsuura, Masashi; Tezuka, Nobuki; Sugimoto, Satoshi; Goto, Ryota
2011-01-01
This study provides the influence of microstructural change of the interface between Nd 2 Fe 14 B and Nd-O phases on coercivity of Nd-Fe-B thin films during annealing at low temperature (∼350 deg. C). All films were prepared by using ultra high vacuum (UHV) magnetron sputtering, and the Nd-Fe-B layer was oxidized under Ar gas atmosphere (O 2 content; ∼2 Vol.ppm). Then, the films were annealed at 250-350 deg. C under UHV condition. After oxidation, the coercivity of Nd-Fe-B film decreased to around 40% of the coercivity of as-deposited Nd-Fe-B film. The Nd-rich phase changed from α-Nd to amorphous Nd(-O), and the interface of Nd 2 Fe 14 B/Nd(-O) became rough. In the Nd-Fe-B films oxidized and subsequent annealed at 350 deg. C, the coercivity decreased to around 20%. In the films, poly crystalline hcp Nd 2 O 3 phase crystallized in Nd-rich phase, and there were some steps at the surface of Nd 2 Fe 14 B phase contacting with hcp Nd 2 O 3 phase. Regardless of crystal orientation of Nd 2 Fe 14 B, the microstructural changes of the interface described above were observed.
Magnetization switching of NiFeSiB free layers for magnetic tunnel junctions
International Nuclear Information System (INIS)
Chun, B.S.; Ko, S.P.; Oh, B.S.; Hwang, J.Y.; Rhee, J.R.; Kim, T.W.; Saito, S.; Yoshimura, S.; Tsunoda, M.; Takahashi, M.; Kim, Y.K.
2006-01-01
Ferromagnetic amorphous Ni 16 Fe 62 Si 8 B 14 layer have been studied as free layers for magnetic tunnel junctions (MTJs) to enhance cell switching performance. Traditional MTJ free layer materials such as NiFe and CoFe were also prepared for switching comparison purposes. Both NiFeSiB and NiFe resulted in an order of magnitude smaller switching fields compared to the CoFe. The switching field was further reduced for the synthetic antiferromagnetic NiFeSiB free layered structure
Processing and physical metallurgy of NdFeB and other R.E. magnets
International Nuclear Information System (INIS)
Ormerod, J.
1985-01-01
The background to the developmetn of NdFeB-based permanent magnets is described. The processing of NdFeB permanent magnets is outlined and compared with the production of SmCo-based permanent magnets. Some metallographic observations of sintered NdFeB magnets are presented. Finally, the improvement and future development of NdFeB and related permanent magnet materials are discussed
The role of Mg interface layer in MgO magnetic tunnel junctions with CoFe and CoFeB electrodes
Directory of Open Access Journals (Sweden)
Hyunsoo Yang
2012-03-01
Full Text Available The tunneling spin polarization (TSP is directly measured from reactively sputter deposited crystalline MgO tunnel barriers with various CoFe(B compositions using superconducting tunneling spectroscopy. We find that the Mg interface layer thickness dependence of TSP values for CoFeB/Mg/MgO junctions is substantially different from those for CoFe/Mg/MgO especially in the pre-annealed samples due to the formation of boron oxide at the CoFeB/MgO interface. Annealing depletes boron at the interface thus requiring a finite Mg interface layer to prevent CoFeOx formation at the CoFeB/MgO interface so that the TSP values can be optimized by controlling Mg thickness.
High-performance nanocrystalline NdFeB magnets by CAPA process
Energy Technology Data Exchange (ETDEWEB)
Kim, H.T. [Tesla Co., Ltd., 340-1 Songsan-Ri, Yanggam-Myeon, Hwasung City, Gyeonggi-Do, 445-396 (Korea, Republic of)]. E-mail: htkim@gotesla.com; Kim, Y.B. [Korea Research Institute Standards and Sciences, 305-600, Daejeon (Korea, Republic of); Jeon, J.W. [Chonbuk National University, 756-356, Jeonju (Korea, Republic of); Jang, I.H. [Tesla Co., Ltd., 340-1 Songsan-Ri, Yanggam-Myeon, Hwasung City, Gyeonggi-Do, 445-396 (Korea, Republic of); Kapustin, G.A. [RRC Kurchatov Institute, Moscow, 123182 (Russian Federation); Kim, H.S. [Chonbuk National University, 756-356, Jeonju (Korea, Republic of)
2006-09-15
The anisotropic NdFeB magnets were prepared from the melt-spun isotropic powders by CAPA process. The precursor isotropic magnet shows the uniform magnetic properties according to the overall position in the magnet. In the case of the anisotropic magnet, the outer position shows higher remanence and energy product compared to the center position. The magnetic properties of the anisotropic magnet obtained from Nd{sub 14}Fe{sub 80}B{sub 6} powders are B{sub r}=15kG, {sub i}H{sub c}=4.1kOe and BH{sub max}=36MGOe. In the case of addition of Zn to Nd{sub 14}Fe{sub 80}B{sub 6} powders, the energy product increased because of the improved coercivity. The magnetic properties of the Zn-added magnet are B{sub r}=14.5kG, {sub i}H{sub c}=9.7kOe and BH{sub max}=52MGOe. The Zn addition is effective to depress Nd{sub 2}Fe{sub 14}B grain growth of the interparticle regions during plastic deformation.
Crystallographic orientation analysis in HDDR process of anisotropic Nd-Fe-B magnet powders
Energy Technology Data Exchange (ETDEWEB)
Takizawa, Rina, E-mail: 3ES15002M@s.kyushu-u.ac.jp [Department of Applied Science for Electronics and Materials, Interdisciplinary Graduate School of Science and Engineering, Kyushu University, 6-1 Kasugakoen, Kasuga 816-8580 (Japan); Itakura, Masaru [Department of Applied Science for Electronics and Materials, Faculty of Engineering Sciences, Kyushu University, 6-1 Kasugakoen, Kasuga, Fukuoka 816-8580 (Japan); Katayama, Nobuhiro; Morimoto, Koichiro [R& D Division, Toda Kogyo Corp., 1-4 Meijishinkai, Otake, Hiroshima 739-0652 (Japan)
2017-07-01
Highlights: • Over 70% of the Nd{sub 2}Fe{sub 14}B grains after the HDDR process are aligned within 30°. • The c-axis alignment of Nd{sub 2}Fe{sub 14}B slightly deteriorates by the Nd-rich phase formation. • α-Fe grains possess a uniaxial and 〈1 1 3〉 oriented texture in the decomposed stage. • α-Fe is most likely to induce the texture development of recombined Nd{sub 2}Fe{sub 14}B. - Abstract: Microstructural changes and crystallographic orientation information in the hydrogenation-decomposition-desorption-recombination (HDDR) process of Nd-Fe-B alloy were investigated using electron backscatter diffraction (EBSD) and precession electron diffraction (PED) in order to understand the mechanism of anisotropy inducement in the HDDR process. Recombined Nd{sub 2}Fe{sub 14}B grains were found to nucleate at the interfaces between NdH{sub 2} and α-Fe grains and to have a [0 0 1]-oriented texture from the beginning of the recombination reaction. The Fe grains form with alignment of one of the 〈1 1 3〉 directions at decomposed stage. This suggests that α-Fe most likely induces texture development of recombined Nd{sub 2}Fe{sub 14}B.
Energy Technology Data Exchange (ETDEWEB)
Liu, Yue-Lin, E-mail: liuyuelin@ss.buaa.edu.cn; Yu, Yang; Dai, Zhen-Hong
2015-01-15
Using first-principles calculations, we investigate the stabilities of He and He{sub n}-vacancy (He{sub n}V) clusters in α-Fe and W. Vacancy formation energies are 2.08 eV in α-Fe and 3.11 eV in W, respectively. Single He in both α-Fe and W prefers to occupy the tetrahedral interstitial site. We recalculated the He solution energy considering the effect of zero-point energy (ZPE). The ZPEs of He in α-Fe and W at the tetrahedral (octahedral) interstitial site are 0.072 eV (0.031 eV) and 0.078 eV (0.034 eV), respectively. The trapping energies of single He at vacancy in α-Fe and W are −2.39 eV and −4.55 eV, respectively. By sequentially adding He into vacancy, a monovacancy trap up to 10 He atoms distributing in the vacancy vicinity. Based on the above results combined with statistical model, we evaluate the concentrations of all relevant He{sub n}V clusters as a function of He chemical potential. The critical He{sub n}V concentration is found to be ∼10{sup −40} (atomic) at the critical temperature T = 600 K in α-Fe and T = 1600 K in W, respectively. Beyond the critical He{sub n}V concentrations, considerable He{sub n}V aggregate to form He{sub n}V{sub m} clusters. By further growing of He{sub n}V{sub m}, the He{sub n}V{sub m} clusters grow bigger resulting in the larger He bubble formation.
The analysis of adhesion failure between Ni-coating and sintered NdFeB substrate
Energy Technology Data Exchange (ETDEWEB)
Hengxiu, Y; Yong, D; Zhenlun, S, E-mail: yanghengxiu@nimte.ac.cn [Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, 315201 (China)
2011-01-01
Ni-coating was widely used to protect the sintered NdFeB magnet from corrosion by Watt electro-deposition solution. However, the protection failure always occurs due to poor adhesion strength between Ni-coating and NdFeB substrate. In present work, the adhesion strength of the Ni-coating on NdFeB substrate was measured by vertical tensile method to strip Ni-coating from NdFeB substrate. The results revealed that the adhesion failure was occurred in the side of the NdFeB substrate due to a weak zone sometimes shown cracks located inside of NdFeB substrate, rather than in the interface between Ni-coating and NdFeB substrate. Comparing with cross section morphology of NdFeB magnet after pretreatment, it is concluded that the crack could be formed during the electro-deposition process. The effect of the pH value of bath on adhesion strength indicated that the crack could be induced due to electrochemical hydrogenation of NdFeB substrate during electro-deposition.
Périgo, E A; Silva, S C; de Sousa, E M B; Freitas, A A; Cohen, R; Nagamine, L C C M; Takiishi, H; Landgraf, F J G
2012-05-04
Nanoparticles were prepared from a NdFeB-based alloy using the hydrogen decrepitation process together with high-energy ball milling and tested as heating agent for magnetic hyperthermia. In the milling time range evaluated (up to 10 h), the magnetic moment per mass at H = 1.59 MA m(-1) is superior than 70 A m(2) kg(-1); however, the intrinsic coercivity might be inferior than 20 kA m(-1). The material presents both ferromagnetic and superparamagnetic particles constituted by a mixture of phases due to the incomplete disproportionation reaction of Nd(2)Fe(14)BH(x) during milling. Solutions prepared with deionized water and magnetic particles exposed to an AC magnetic field (H(max) ~ 3.7 kA m(-1) and f = 228 kHz) exhibited 26 K ≤ ΔT(max) ≤ 44 K with a maximum estimated specific absorption rate (SAR) of 225 W kg(-1). For the pure magnetic material milled for the longest period of time (10 h), the SAR was estimated as ~2500 W kg(-1). In vitro tests indicated that the powders have acceptable cytotoxicity over a wide range of concentration (0.1-100 µg ml(-1)) due to the coating applied during milling.
Steam reforming of bio-oil from coconut shell pyrolysis over Fe/olivine catalyst
International Nuclear Information System (INIS)
Quan, Cui; Xu, Shaoping; Zhou, Congcong
2017-01-01
Highlights: • Steam reforming of the actual bio-oil was investigated with Fe/olivine catalyst. • Most of phenols in bio-oil were converted into gas products. • A carbon conversion of 97.2% was obtained under optimized conditions. - Abstract: Catalytic steam reforming of coconut shell pyrolysis bio-oil over Fe/olivine catalyst was conducted in a fixed-bed quartz reactor. The effects of calcination temperature, iron loading, reaction temperature, steam to carbon ratio (S/C), bio-oil weight hourly space velocity (W b HSV) on gas composition and carbon conversion were investigated. The results indicate that Fe/olivine has good activity for steam reforming of bio-oil, the couple Fe 2+/3+ /Fe 2+ may be sufficiently efficient for C–C, C–O and C–H breaking. After steam reforming, most of the phenolics in pyrolysis oil are converted into light molecular compounds such as H 2 , CO, CO 2 , and CH 4 . The H 2 concentration and carbon conversion were enhanced by increasing reaction temperature from 750 to 800 °C and the S/C from 1.5 to 2, but decreased with increasing calcination temperature. In the W b HSV range of 0.5–0.6, the hydrogen concentration decreased obviously, whereas it decreased slightly by further increasing W b HSV. The highest hydrogen concentration of 47.6 vol% was obtained among the catalysts tested, and the best carbon conversion was 97.2% over 10% Fe/olivine catalyst under the reforming conditions of temperature = 800 °C, W b HSV = 0.5, S/C = 2.
Erosion resistance of FeAl-TiB2 and FeAl-WC at room and elevated temperatures
International Nuclear Information System (INIS)
Alman, D.E.; Tylczak, J.H.; Hawk, J.A.
2000-01-01
The resistance of FeAl-40%TiB 2 and FeAl-80%WC cermets to solid particle erosion at 25, 180, 500 and 700 C was evaluated and compared to the behavior of WC-6%Co (Co-90%WC) cemented carbides. Even though the WC-Co contained a higher volume fraction of the hard phase, the erosion rates of the FeAl-cermets were similar in magnitude to the erosion rates of the WC-Co. However, the erosion rates of the FeAl-cermets either were constant (FeAl-TiB 2 ) or decreased (FeAl-WC) with increasing test temperature; whereas, the erosion rates of the WC-Co cemented carbides increased with increasing test temperature. This indicated that once the microstructures of the FeAl-cermets are optimized for wear resistance, these materials might make promising candidates for high-temperature wear applications
Corrosion behaviour of Nd-Fe-B magnets containing Co and Cr
International Nuclear Information System (INIS)
Pawlowska, G.; Bala, H.; Szymura, S.
1993-01-01
The effect of partial substitution of iron by Co and Cr on corrosion behaviour of Nd 16 Fe 76 B 8 permanent magnets has been investigated. Small additions of Cr (1 to 4%at) are enough to ensure maximal corrosion inhibition. Greater amount of Cr into Nd-Fe-B alloy (>8%at), against expectations, practically do not affect the corrosion behaviour and additionally, considerably worsen its magnetic properties. Corrosion tests have shown a distinct effect of cobalt addition on the inhibition of both acid corrosion and the abnormal dissolution process of the Nd-Fe-Co-B magnets. Cobalt additions inhibit the atmosphere corrosion of Nd-Fe-B permanent magnets, especially a salt-spray environment. (author). 6 refs, 4 figs, 1 tab
Moessbauer study of isothermally annealed amorphous Fe-Nb-Cu-Si-B alloys
International Nuclear Information System (INIS)
Sitek, J.; Toth, I.; Miglierini, M.
1993-01-01
Amorphous ribbons of Fe 73.5 Nb 3 Cu 1 Si 13.5 B 9 have been annealed above the crystallization temperature. Annealed samples consisted of crystalline and amorphous phases in a wide temperature range. Two samples of different thicknesses of 33 μm and 27 μm were isothermally annealed at a temperature of 545 C from 0.5 to 5 h in a vacuum furnace. The amount of crystalline phase increases rapidly in the ticker sample. The crystalline part of the Moessbauer spectrum consists of four sharp sextets which can be assigned to a DO 3 -structure FeSi alloy. After 700 C annealing the amorphous phase was not observed and the crystalline phase consisted of the DO 3 -structure FeSi alloy, paramagnetic FeNbB and presumably Fe 23 B 6 and Fe 3 SiB 2 . (orig.)
Jakobsson, Lars Klemet; Tranell, Gabriella; Jung, In-Ho
2017-02-01
NdFeB magnet scrap is an alternative source of neodymium that could have a significantly lower impact on the environment than current mining and extraction processes. Neodymium can be readily oxidized in the presence of oxygen, which makes it easy to recover neodymium in oxide form. Thermochemical data and phase diagrams for neodymium oxide containing systems is, however, very limited. Thermodynamic modeling of the B2O3-FeO-Fe2O3-Nd2O3 system was hence performed to obtain accurate phase diagrams and thermochemical properties of the system. Key phase diagram experiments were also carried out for the FeO-Nd2O3 system in saturation with iron to improve the accuracy of the present modeling. The modified quasichemical model was used to describe the Gibbs energy of the liquid oxide phase. The Gibbs energy functions of the liquid phase and the solids were optimized to reproduce all available and reliable phase diagram data, and thermochemical properties of the system. Finally the optimized database was applied to calculate conditions for selective oxidation of neodymium from NdFeB magnet waste.
Directory of Open Access Journals (Sweden)
Zbigniew Joskowski
2012-01-01
Full Text Available Artykuł prezentuje zasób norbertańskiej silvae rerum przechowywanej obecnie w dziale zbiorów specjalnych Biblioteki Prowincjalnej Franciszkanów w Gnieźnie (BPFG. Sylwa stanowi swoistą bibliotekę: zbiór odpisów mów, oracji dotyczących bieżącego życia politycznego XVIII wieku, dzieł poetyckich, życzeń, powinszowań okazjonalnych, a także twórczości własnej nieznanego zakonnika norbertańskiego – twórcy i właściciela sylwy.
Study of interlayer coupling between FePt and FeCoB thin films through MgO spacer layer
Singh, Sadhana; Kumar, Dileep; Gupta, Mukul; Reddy, V. Raghvendra
2017-05-01
Interlayer exchange coupling between hard-FePt and soft-FeCoB magnetic layers has been studied with increasing thickness of insulator MgO spacer layer in FePt/MgO/FeCoB sandwiched structure. A series of the samples were prepared in identical condition using ion beam sputtering method and characterized for their magnetic and structural properties using magneto-optical Kerr effect (MOKE) and X-ray reflectivity measurements. The nature of coupling between FePt and FeCoB was found to be ferromagnetic which decreases exponentially with increasing thickness of MgO layer. At very low thickness of MgO layer, both layers were found strongly coupled thus exhibiting coherent magnetization reversal. At higher thickness, both layers were found decoupled and magnetization reversal occurred at different switching fields. Strong coupling at very low thickness is attributed to pin holes in MgO layer which lead to direct coupling whereas on increasing thickness, coupling may arise due to magneto-static interactions.
Saturation of VCMA in out-of-plane magnetized CoFeB/MgO/CoFeB magnetic tunnel junctions
Williamson, M.; de Rozieres, M.; Almasi, H.; Chao, X.; Wang, W.; Wang, J.-P.; Tsoi, M.
2018-05-01
Voltage controlled magnetic anisotropy (VCMA) currently attracts considerable attention as a novel method to control and manipulate magnetic moments in high-speed and low-power spintronic applications based on magnetic tunnel junctions (MTJs). In our experiments, we use ferromagnetic resonance (FMR) to study and quantify VCMA in out-of-plane magnetized CoFeB/MgO/CoFeB MTJ pillars. FMR is excited by applying a microwave current and detected via a small rectified voltage which develops across MTJ at resonance. The VCMA effective field can be extracted from the measured resonance field and was found to vary as a function of electrical bias applied to MTJ. At low applied biases, we observe a linear shift of the VCMA field as a function of the applied voltage which is consistent with the VCMA picture based on the bias-induced electron migration across the MgO/CoFeB interface. At higher biases, both positive and negative, we observe a deviation from the linear behavior which may indicate a saturation of the VCMA effect. These results are important for the design of MTJ-based applications.
Nanocomposite Nd-Y-Fe-B-Mo bulk magnets prepared by injection casting technique
Energy Technology Data Exchange (ETDEWEB)
Tao, Shan [Magnetism Key Laboratory of Zhejiang Province, China Jiliang University, Hangzhou 310018 (China); Ahmad, Zubair [State Key Laboratory of Silicon Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zhang, Pengyue [Magnetism Key Laboratory of Zhejiang Province, China Jiliang University, Hangzhou 310018 (China); Yan, Mi, E-mail: mse_yanmi@zju.edu.cn [State Key Laboratory of Silicon Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zheng, Xiaomei [Magnetism Key Laboratory of Zhejiang Province, China Jiliang University, Hangzhou 310018 (China)
2017-09-01
Highlights: • Nanocomposite Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} sheet magnets were synthesized by injection casting. • High coercivity of 1289 kA/m was obtained for the directly casted magnet. • Magnetic properties arise from magnetically exchange coupled soft and hard phases. - Abstract: The phase composition, magnetic and microstructural properties of Nd{sub 2}Fe{sub 14}B/(α-Fe, Fe{sub 3}B) nanocomposite magnets produced by injection casting technique have been studied. Magnetic hysteresis loop of the Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} permanent magnet demonstrates the coercivity as high as 1289 kA/m. Electron microscopy elucidates a microstructure composed of magnetically soft α-Fe, Fe{sub 3}B and hard Nd{sub 2}Fe{sub 14}B/Y{sub 2}Fe{sub 14}B nanograins (20–50 nm) separated by ultra-thin grain boundary layer. The Henkel plot curve of the Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} magnet yields the existence of exchange coupling interactions between soft and hard phases. Macroscopically large size sheet magnet is obtained due to high glass forming ability of the Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} alloy derived from large atomic radius mismatch and negative enthalpy of alloy constituent elements. The high coercivity of the magnet is attributed to the magnetically hard phase increment, nucleation of reverse domains and the presence of thin grain boundary phase. Good magnetic properties such as remanence of 0.51 T, coercivity of 1289 kA/m and maximum energy product of 46.2 kJ/m{sup 3} are obtained in directly casted Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} sheet magnets.
Energy Technology Data Exchange (ETDEWEB)
Kaga, H. [Hokkaido Industrial Technology Center, Sapporo (Japan); Carrillo-Heian, E.M.; Munir, Z.A. [University of California, CA, (United States)
2000-08-15
The reactive sintered compacts of Ti-W-Cr-B mixed powders were manufactured by a pulse electric current technique. Identification and characterization of the resulting boride phase were done using EPMA, XRD and other methods. The density of the sintered compacts rose rapidly with sintering temperature up to 1,773 K, at which temperature the relative density was 94%. Above this temperature, the density rose only slightly with increasing sintering temperature. The borides of Ti and W were synthesized from mixed metal powders by this method. The type of boride formed and its composition depended on sintering temperature. Compacts sintered at lower temperatures consisted of WB{sub 2} and TiB{sub 2} phases, but at the highest sintering temperature, 2,173K, the main phase was (Ti, W, Cr)B{sub 2} solid solution, in which W and Cr were dissolved in TiB{sub 2}. There was also a very small amount of {beta}-(W, Ti, Cr)B phase. By annealing compact sintered at high temperature, the (Ti, W, Cr)B{sub 2} solid solution phase decomposed and the amount decreased. (author)
An investigation of fatigue in LIGA Ni MEMS thin films
International Nuclear Information System (INIS)
Allameh, S.M.; Lou, J.; Kavishe, F.; Buchheit, T.; Soboyejo, W.O.
2004-01-01
This paper presents results of an experimental study of fatigue in LIGA Ni micro-electro-mechanical systems (MEMS)/thin films produced by electroplating from a sulfamate bath at a current density of 50 mA/cm 2 . Following a brief description of microstructure and micro-tensile properties, the results of stress-life (S-N) experiments are presented for specimens with thicknesses of 70 and 270 μm. Specimens with the thicker cross-sections (270 μm thick) are shown to have comparable fatigue resistance to annealed bulk Ni in the as-plated condition. The thinner specimens (70 μm thick) have comparable fatigue resistance to hardened Ni, and better fatigue resistance than the thicker samples. The underlying fatigue fracture modes are elucidated via scanning electron microscopy. The implications of the results are then discussed for the failure analysis of LIGA Ni MEMS structures
New technique using LigaSure for endoscopic mucomyotomy of Zenker's diverticulum
DEFF Research Database (Denmark)
Nielsen, Hans Ulrik Kjaerem; Trolle, Waldemar; Rubek, Niclas
2014-01-01
OBJECTIVES/HYPOTHESIS: The purpose of this study is to present a new approach for treatment of Zenker's diverticulum using the LigaSure (Covidien, Mansfield, MA) technique. STUDY DESIGN: A consecutive study with follow-up of 15 patients with Zenker's diverticulum endoscopically treated using...... patients were followed up 5 to 14 months after discharge. RESULTS: The median age of patients was 76 years. The diverticula measured between 2 and 7 cm. The median time of surgery was 33 minutes. All patients but one resumed oral intake within 24 hours. One patient experienced prolonged coughing...... condition. As a new operative instrument, the LigaSure technique constitutes in our opinion a valid and easy alternative for treatment of Zenker's diverticulum compared to other endoscopic techniques....
Zhao, Chong-Jun; Lu, Xiang-An; Zhao, Zhi-Duo; Li, Ming-Hua; Zhang, Peng; Wang, Bao-Yi; Cao, Xing-Zhong; Zhang, Jing-Yan; Yu, Guang-Hua
2013-09-01
As one of the most powerful tools for investigation of defects of materials, positron annihilation spectroscopy was employed to explore the thermal effects on the film microstructure evolution in CoFeB/MgO/CoFeB heterostructures. It is found that high annealing temperature can drive vacancy defects agglomeration and ordering acceleration in the MgO barrier. Meanwhile, another important type of defects, vacancy clusters, which are formed via the agglomeration of vacancy defects in the MgO barrier after annealing, still exists inside the MgO barrier. All these behaviors in the MgO barrier could potentially impact the overall performance in MgO based magnetic tunnel junctions.
Electrodeposition and Properties of Copper Layer on NdFeB Device
Directory of Open Access Journals (Sweden)
LI Yue
2017-06-01
Full Text Available To decrease the impact of the regular Ni/Cu/Ni coating on the magnetic performance of sintered NdFeB device, alkaline system of HEDP complexing agent was applied to directly electro-deposit copper layer on NdFeB matrix, then nickel layer was electrodeposited on the copper layer and Cu/Ni coating was finally obtained to replace the regular Ni/Cu/Ni coating. The influence of concentration of HEDP complexing agent on deposition course was tested by electrochemical testing; morphology of copper layer was characterized by SEM, XRD and TEM; the binding force of copper layer and the thermal reduction of magnetic of NdFeB caused by electrodeposited coating were respectively explored through the thermal cycle test and thermal demagnetization test. The results show that the concentration of HEDP has great impact on the deposition overpotential of copper. In the initial electrodepositing stage, copper particles precipitate at the grain boundaries of NdFeB magnets with a preferred (111 orientation. The copper layer is compact and has enough binding force with the NdFeB matrix to meet the requirements in SJ 1282-1977. Furthermore, the thermal demagnetization loss rate of the sintered NdFeB with the protection of Cu/Ni coating is significantly less than that with the protection of Ni/Cu/Ni coating.
Longitudinal recording on FePt and FePtX (X = B, Ni) intermetallic compounds
Li, Ning
1999-11-01
Near field recording on high coercivity FePt intermetallic compound media using a high Bsat write element was investigated. Untextured FePt media were prepared by magnetron sputtering on ZrO2 disks at a substrate temperature of 450°C, with post annealing at 450°C for 8 hrs. Both multilayer and cosputtered precursors produced the ordered tetragonal L10 phase with high coercivity between 5kOe and 12kOe. To improve readback noise decrease magnetic domain size, FePtB media were subsequently prepared by cosputtering. Over-write, roll-off, signal to noise ratio and non-linear transition shift (NLTS) ere measured by both metal in gap (MIG) and merged MR heads. FePtB media showed similar NLTS to commercial CoCrPtTa longitudinal media, but 5dB lower signal to noise ratio. By operating recording transducers in near contact, reasonable values of (>30dB) could be obtained. VSM Rotational Transverse Magnetization has been used for measuring the anisotropy field of magnetic thin films. Magnetization reversal during rotation of a 2D isotropic an applied field is discussed. The relationship between the transverse magnetization My and the applied field H was numerically solved. An excellent approximation for the transverse magnetization is found to be: My/Ms=A(1- H/Hk) 2.5, where A = 1.1434, and Hk is the anisotropy field. For curve fitting to experimental data, both A and Hk were used as fitting parameters. Comparison between a constructed torque hysteresis method and this VSM RTM method have been made theoretically and experimentally. Both results showed that VSM RTM will give better extrapolation of the anisotropy field. The torque measurement will slightly overestimate the anisotropy field. The anisotropy fields of FePt and FePtX (X = B, Ni) films were characterized using this VSM RTM technique with comparison to a CoCrTaPt disk. Anisotropy energy was derived. Hc/Hk was used as an indicator for coherent rotation of a single domain. Interactions between magnetic domains were
Formation and crystallization kinetics of Nd-Fe-B-based bulk amorphous alloy
Energy Technology Data Exchange (ETDEWEB)
Wu, Qiong; Ge, Hongliang; Zhang, Pengyue; Li, Dongyun; Wang, Zisheng [China Jiliang University, Magnetism Key Laboratory of Zhejiang Province, Hangzhou (China)
2014-06-15
In order to improve the glass-forming ability (GFA) of Nd-Fe-B ternary alloys to obtain fully amorphous bulk Nd-Fe-B-based alloy, the effects of Mo and Y doping on GFA of the alloys were investigated. It was found that the substitution of Mo for Fe and Y for Nd enhanced the GFA of the Nd-Y-Fe-Mo-B alloys. It was also revealed that the GFA of the samples was optimized by 4 at.% Mo doping and increased with theYcontent. The fully amorphous structures were all formed in the Nd{sub 6-x}Y{sub x}Fe{sub 68}Mo{sub 4}B{sub 22} (x =1-5) alloy rods with 1.5 mm-diameter. After subsequent crystallization, the devitrified Nd{sub 3}Y{sub 3}Fe{sub 68}Mo{sub 4}B{sub 22} alloy rod exhibited a uniform distribution of grains with a coercivity of 364.1 kA/m. The crystallization behavior of Nd{sub 3}Y{sub 3}Fe{sub 68}Mo{sub 4}B{sub 22} BMG was investigated in isothermal situation. The Avrami exponent n determined by JAM plot is lower than 2.5, implying that the crystallization is mainly governed by a growth of particles with decreasing nucleation rate. (orig.)
Study of Nd-Fe-B alloys with nonstoichiometric Nd content in optimal magnetic state
Directory of Open Access Journals (Sweden)
Ćosović V.
2009-01-01
Full Text Available Characterization of two rapid-quenched Nd-Fe-B alloys with nonstoichiometric Nd content in the optimized magnetic state was carried out using the X-ray diffractometry (XRD, 57Fe Mössbauer spectroscopic phase analysis (MS, electron microscopy (TEM, high resolution TEM (HREM and Superconducting Quantum Interference Device (SQUID magnetometer. The experimental results demonstrate the fundamental difference in the structure and magnetic properties of the two investigated alloys in the optimized magnetic state. The Nd-Fe-B alloy with the reduced Nd content (Nd4.5Fe77B18.5 was found to have the nanocomposite structure of Fe3B/Nd2Fe14B and partly α-Fe/Nd2Fe14B, with mean grain size below 30 nm. On the other side, the overstoichiometric Nd14Fe79B7 alloy has almost a monophase structure with the dominant content of the hard magnetic phase Nd2Fe14B (up to 95 wt. % and a mean crystallite size about 60 nm, as determined by XRD and TEM analysis. The results of magnetic measurements on SQUID magnetometer also suggest the nanocomposite structure of the Nd-low alloy and nanocrystalline decoupled structure of the Nd-rich alloy after the optimal heat treatment.
Microstructure and Magnetic Properties of NdFeB Films through Nd Surface Diffusion Process
Directory of Open Access Journals (Sweden)
Wenfeng Liu
2017-01-01
Full Text Available Ta/Nd/NdFeB/Nd/Ta films were deposited by magnetron sputtering on Si (100 substrates and subsequently annealed for 30 min at 923 K in vacuum. It was found that the microstructure and magnetic properties of Ta/Nd/NdFeB/Nd/Ta films strongly depend on the NdFeB layer thickness. With NdFeB layer thickness increasing, both the grain size and the strain firstly reduce and then increase. When NdFeB layer thickness is 750 nm, the strain reaches the minimum value. Meanwhile, both the in-plane and perpendicular coercivities firstly drastically increase and then slowly decrease with NdFeB layer thickness increasing. The highest in-plane and perpendicular coercivities can be obtained at NdFeB layer thickness of 750 nm, which are 21.2 kOe and 19.5 kOe, respectively. In addition, the high remanence ratio (remanent magnetization/saturation magnetization of 0.87 can also be achieved in Ta/Nd/NdFeB (750 nm/Nd/Ta film.
Microstructure, Texture, and Mechanical Behavior of As-cast Ni-Fe-W Matrix Alloy
Rao, A. Sambasiva; Manda, Premkumar; Mohan, M. K.; Nandy, T. K.; Singh, A. K.
2018-04-01
This article describes the tensile properties, flow, and work-hardening behavior of an experimental alloy 53Ni-29Fe-18W in as-cast condition. The microstructure of the alloy 53Ni-29Fe-18W displays single phase (fcc) in as-cast condition along with typical dendritic features. The bulk texture of the as-cast alloy reveals the triclinic sample symmetry and characteristic nature of coarse-grained materials. The alloy exhibits maximum strength ( σ YS and σ UTS) values along the transverse direction. The elongation values are maximum and minimum along the transverse and longitudinal directions, respectively. Tensile fracture surfaces of both the longitudinal and transverse samples display complete ductile fracture features. Two types of slip lines, namely, planar and intersecting, are observed in deformed specimens and the density of slip lines increases with increasing the amount of deformation. The alloy displays moderate in-plane anisotropy ( A IP) and reasonably low anisotropic index ( δ) values, respectively. The instantaneous or work-hardening rate curves portray three typical stages (I through III) along both the longitudinal and transverse directions. The alloy exhibits dislocation-controlled strain hardening during tensile testing, and slip is the predominant deformation mechanism.
Adjustable ferromagnetic resonance frequency in CoO/CoFeB system
Energy Technology Data Exchange (ETDEWEB)
Bonneau-Brault, A. [CEA Le Ripault, BP16, 37260 Monts (France); GREMAN, CNRS UMR 7347, University of Tours, 37200 Tours (France); Dubourg, S. [CEA Le Ripault, BP16, 37260 Monts (France); Thiaville, A. [LPS, CNRS UMR 8502, University of Paris-Sud, 91405 Orsay Cedex (France); Rioual, S. [LMB EA4522, University of Brest, 6 av. Le Gorgeu, 29238 Brest Cedex 3 (France); Valente, D. [GREMAN, CNRS UMR 7347, University of Tours, 37200 Tours (France)
2015-01-21
Static and dynamic properties of (CoO/CoFeB){sub n} multilayers have been investigated. An anisotropy field enhancement was evidenced when the CoO layer was deposited under the CoFeB layer. Tuning the relative CoFeB and CoO layers thicknesses, high ferromagnetic resonance frequencies up to 4 GHz were achieved. The coupling effect between the CoO and CoFeB layers was induced by a dipolar coupling due to the anisotropic roughness topology of the CoO layer. This anisotropic roughness was induced by the deposition geometry and evidenced by atomic force microscopy. The strength of the dipolar interfacial coupling was calculated thanks to Schlömann's model. Multilayer stacks were fabricated and the magnetic properties observed for the trilayers could be maintained.
Adjustable ferromagnetic resonance frequency in CoO/CoFeB system
International Nuclear Information System (INIS)
Bonneau-Brault, A.; Dubourg, S.; Thiaville, A.; Rioual, S.; Valente, D.
2015-01-01
Static and dynamic properties of (CoO/CoFeB) n multilayers have been investigated. An anisotropy field enhancement was evidenced when the CoO layer was deposited under the CoFeB layer. Tuning the relative CoFeB and CoO layers thicknesses, high ferromagnetic resonance frequencies up to 4 GHz were achieved. The coupling effect between the CoO and CoFeB layers was induced by a dipolar coupling due to the anisotropic roughness topology of the CoO layer. This anisotropic roughness was induced by the deposition geometry and evidenced by atomic force microscopy. The strength of the dipolar interfacial coupling was calculated thanks to Schlömann's model. Multilayer stacks were fabricated and the magnetic properties observed for the trilayers could be maintained
Wei, Xiang; Chen, Zhiguo; Zhong, Jue; Wang, Li; Wang, Yipeng; Shu, Zhongliang
2018-06-01
The structural, mechanical, electronic and magnetic properties of Fe8-xCrxB4 (x = 0, 0.25, 0.5, 1, 2, 3, 4, 5, 6, 7 and 8) have been investigated by first-principles calculation. It was found that the calculated structural parameters are well consistent with available experimental data. Moreover, all studied compounds are thermodynamically stable phases. On the whole, the moduli of the compounds firstly increase and then decrease with the increase of Cr concentration, whereas the variation of hardness exhibits more fluctuations. All Cr-doped Fe2B have better ductility than Fe2B except Fe2Cr6B4 and Fe5Cr3B4. Interestingly, Fe4Cr4B4 is of not only the slightly larger hardness, but also much better ductility than Fe2B. As the Cr concentration is lower than 20 wt%, the hardness of Cr-doped Fe2B slightly decreases with increasing Cr, whereas the sharply increased hardness of (Fe, Cr)2B in Fe-B alloys or boriding layer should be attributed to the multiple alloying effects resulting from Cr and the other alloying elements. The electronic structures revealed that the Fe-B and/or Cr-B bonds are mainly responsible for their mechanical properties, and the M-N (M = Fe or Cr, N = Fe or Cr) bonds in 〈2 2 0〉 and 〈1 1 3〉 orientations show covalent character. Additionally, the magnetic moments (Ms) of the compounds do not monotonically decrease with increasing Cr.
Structure and Properties of Nd-Fe-B Alloy Subjected to HDDR Process
Directory of Open Access Journals (Sweden)
Szymański M.
2016-03-01
Full Text Available In this paper the Hydrogenation, Disproportionation, Desorption and Recombination (HDDR route was tested, for the Nd-Fe-B master alloy, as a prospective procedure for recycling of sintered scrap neodymium magnets. The HDDR method is based on the hydrogen induced reversal phase transformation of Nd-Fe-B alloy: Nd2Fe14B + (2±x H2 = 2NdH2±x + Fe2B + 12Fe. Microstructural observations (SEM, phase constitution studies (XRD and measurement of magnetic properties (VSM were done to investigate the HDDR transformation progress. It was observed that disproportionation reaction starts at the grain boundaries, where the Nd-rich phase is located. Average grain size was reduced and coercive material was produced as a result of the HDDR process. Obtained results are similar to literature data.
The Pulse Thermal Processing of NdFeB-Based Nanocomposite Magnets
Energy Technology Data Exchange (ETDEWEB)
Jin, Z. Q. [University of Texas; Wang, Z. L. [Georgia Institute of Technology; Liu, J. P. [University of Texas; Kadolkar, Puja [ORNL; Ott, Ronald D [ORNL
2006-01-01
Pulse-thermal processing (PTP) based on high-density plasma arc lamp technology has been utilized to crystallize melt-spun NdFeB-based amorphous ribbons to form magnetic nanocomposites consisting of Nd{sub 2}Fe{sub 14}B and {alpha}-Fe phases. After applying suitable pulses, the NdFeB-based ribbons were developed with hard magnetic properties. The highest coercivity can be obtained for ribbons with a thickness of 40 {micro}m after PTP treatments consisting of a 400 A pulse for 0.25 s for ten times. The correlation between PTP parameters and magnetic properties indicates that PTP is an effective approach to control the structure and properties of nanostructured magnetic materials.
Interfacial mixing in double-barrier magnetic tunnel junctions with amorphous NiFeSiB layers
International Nuclear Information System (INIS)
Chun, B.S.; Ko, S.P.; Hwang, J.Y.; Rhee, J.R.; Kim, T.W.; Kim, Y.K.
2007-01-01
Double-barrier magnetic tunnel junctions (DMTJs) comprising Ta 45/Ru 9.5/IrMn 10/CoFe 7/AlO x /free layer (CoFe 4/NiFeSiB 2/CoFe 4, CoFe 10, or NiFeSiB 10)/AlO x /CoFe 7/IrMn 10/Ru 60 (nm) have been examined with an emphasis given on understanding the interfacial mixing effects. The DMTJ, consisted of NiFeSiB, shows low switching field and low bias voltage dependence because the amorphous NiFeSiB has lower M S (=800 emu/cm 3 ) and offers smoother interfaces than polycrystalline CoFe. An interesting feature observed in the CoFe/NiFeSiB/CoFe sandwich free layered DMTJ is the presence of a wavy MR transfer curve at high-resistance region. Because the polycrystalline CoFe usually grows into a columnar structure, diamagnetic CoSi, paramagnetic FeSi, and/or diamagnetic CoB might have been formed during the sputter-deposition process. By employing electron energy loss spectrometry (EELS) and Auger electron spectroscopy (AES), we were able to confirm that Si and B atoms were arranged evenly in the top and bottom portions of AlO x /CoFe interfaces. This means that the interfacial mixing resulted in a distorted magnetization reversal process
High coercivity in Fe-Nb-B-Dy bulk nanocrystalline magnets
Energy Technology Data Exchange (ETDEWEB)
Ziolkowski, Grzegorz; Chrobak, Artur; Klimontko, Joanna [Institute of Physics, University of Silesia, Uniwersytecka 4, 40-007, Katowice (Poland); Chrobak, Dariusz; Rak, Jan [Institute of Materials Science, University of Silesia, 75 Pulku Piechoty 1, 41-500, Chorzow (Poland); Zivotsky, Ondrej; Hendrych, Ales [Department of Physics, VSB-TU Ostrava, Ostrava (Czech Republic)
2016-11-15
The paper refers to structural and magnetic properties of the (Fe{sub 80}Nb{sub 6}B{sub 14}){sub 1-x}Dy{sub x} (x = 0.08, 0.10, 0.12, 0.16) bulk nanocrystalline alloys prepared by making use of the vacuum suction casting technique. The samples are in a form of rods with different diameters d = 1.5, 1, and 0.5 mm. The phase structure was investigated by XRD technique and reveals an occurrence of magnetically hard Dy{sub 2}Fe{sub 14}B as well as other relatively soft Dy-Fe, Fe-B, and Fe phases dependently on the Dy content. The alloys show hard magnetic properties with high coercive field up to 5.5 T (for x = 0.12 and d = 0.5 mm). The observed magnetic hardening effect with the increase of cooling rate (decrease of sample diameter d) can be attributed to a formation of ultra-hard magnetic objects as well as increasing role of low dimensional microstructure. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)
Effect of cerium on the corrosion behaviour of sintered (Nd,Ce)FeB magnet
Yang, Lijing; Bi, Mengxue; Jiang, Jianjun; Ding, Xuefeng; Zhu, Minggang; Li, Wei; Lv, Zhongshan; Song, Zhenlun
2017-06-01
For the balanced consumption of rare-earth elements, cerium (Ce) was partially used for NdFeB magnets instead of Nd. The corrosion behaviour of the (Nd,Ce)FeB magnet with different Ce contents in 3.5% NaCl solution was investigated by SEM, XRD, EDS and electrochemical tests. After immersion, the weight loss was calculated and the magnetic properties of the samples were measured. Results showed that Ce affected the corrosion of the (Nd,Ce)FeB magnet. Compared with the NdFeB magnet without Ce but of the same grade as the magnetic energy product, (Nd,Ce)FeB magnet showed better corrosion resistance. With increased Ce content, the corrosion resistances and magnetic properties of (Nd,Ce)FeB magnets were investigated.
Moessbauer study of isothermally annealed amorphous Fe-Nb-Cu-Si-B alloys
Energy Technology Data Exchange (ETDEWEB)
Sitek, J. (Dept. of Nuclear Physics and Technology, Slovak Technical Univ., Bratislava (Slovakia)); Toth, I. (Dept. of Nuclear Physics and Technology, Slovak Technical Univ., Bratislava (Slovakia)); Miglierini, M. (Dept. of Nuclear Physics and Technology, Slovak Technical Univ., Bratislava (Slovakia))
1993-11-01
Amorphous ribbons of Fe[sub 73.5]Nb[sub 3]Cu[sub 1]Si[sub 13.5]B[sub 9] have been annealed above the crystallization temperature. Annealed samples consisted of crystalline and amorphous phases in a wide temperature range. Two samples of different thicknesses of 33 [mu]m and 27 [mu]m were isothermally annealed at a temperature of 545 C from 0.5 to 5 h in a vacuum furnace. The amount of crystalline phase increases rapidly in the ticker sample. The crystalline part of the Moessbauer spectrum consists of four sharp sextets which can be assigned to a DO[sub 3]-structure FeSi alloy. After 700 C annealing the amorphous phase was not observed and the crystalline phase consisted of the DO[sub 3]-structure FeSi alloy, paramagnetic FeNbB and presumably Fe[sub 23]B[sub 6] and Fe[sub 3]SiB[sub 2]. (orig.)
Core level photoelectron spectroscopy of LiGaS2 and Ga-S bonding in complex sulfides
International Nuclear Information System (INIS)
Atuchin, V.V.; Isaenko, L.I.; Kesler, V.G.; Lobanov, S.I.
2010-01-01
The electronic parameters of the lithium thiogallate LiGaS 2 have been evaluated by X-ray photoelectron spectroscopy (XPS). Spectral features of all constituent element core levels and Auger lines have been considered. The Ga-S bonding effects in Ga-bearing sulfide crystals have been discussed using binding energy difference Δ 2p (S-Ga) = BE(S 2p) - BE(Ga 3d) as a representative parameter to quantify the valence electron shift from gallium to sulfur atoms. The value Δ 2p (S-Ga) = 141.9 eV found for LiGaS 2 is very close to that evaluated for AgGaS 2 . This relation is an indicator of closely coincident ionicity of Ga-S bonds in LiGaS 2 and AgGaS 2 .
Zhu, Hui; Shuman, Stewart
2005-04-01
NAD+-dependent DNA ligase (LigA) is essential for bacterial growth and a potential target for antimicrobial drug discovery. Here we queried the role of 14 conserved amino acids of Escherichia coli LigA by alanine scanning and thereby identified five new residues within the nucleotidyltransferase domain as being essential for LigA function in vitro and in vivo. Structure activity relationships were determined by conservative mutagenesis for the Glu-173, Arg-200, Arg-208, and Arg-277 side chains, as well as four other essential side chains that had been identified previously (Lys-115, Asp-117, Asp-285, and Lys-314). In addition, we identified Lys-290 as important for LigA activity. Reference to the structure of Enterococcus faecalis LigA allowed us to discriminate three classes of essential/important side chains that: (i) contact NAD+ directly (Lys-115, Glu-173, Lys-290, and Lys-314); (ii) comprise the interface between the NMN-binding domain (domain Ia) and the nucleotidyltransferase domain or comprise part of a nick-binding site on the surface of the nucleotidyltransferase domain (Arg-200 and Arg-208); or (iii) stabilize the active site fold of the nucleotidyltransferase domain (Arg-277). Analysis of mutational effects on the isolated ligase adenylylation and phosphodiester formation reactions revealed different functions for essential side chains at different steps of the DNA ligase pathway, consistent with the proposal that the active site is serially remodeled as the reaction proceeds.
Magnetic scanning gate microscopy of CoFeB lateral spin valve
Directory of Open Access Journals (Sweden)
Héctor Corte-León
2017-05-01
Full Text Available Devices comprised of CoFeB nanostructures with perpendicular magnetic anisotropy and non-magnetic Ta channel were operated in thermal lateral spin valve (LSV mode and studied by magnetotransport measurements and magnetic scanning gate microscopy (SGM. Due to the short spin diffusion length of Ta, the spin diffusion signal was suppressed, allowing the study of the contribution from the anomalous Nernst (ANE and anomalous Hall effects (AHE. The magnetotransport measurements identified the switching fields of the CoFeB nanostructures and demonstrated a combination of AHE and ANE when the devices were operated in thermally-driven spin-injection mode. Modified scanning probe microscopy probes were fabricated by placing a NdFeB magnetic bead (MB on the apex of a commercial Si probe. The dipole magnetic field distribution around the MB was characterized by using differential phase contrast technique and direct measurement of the switching field induced by the bead in the CoFeB nanodevices. Using SGM we demonstrate the influence of localized magnetic field on the CoFeB nanostructures near the non-magnetic channel. This approach provides a promising route towards the study of thermal and spin diffusion effects using local magnetic fields.
Magnetic scanning gate microscopy of CoFeB lateral spin valve
Corte-León, Héctor; Scarioni, Alexander Fernandez; Mansell, Rhodri; Krzysteczko, Patryk; Cox, David; McGrouther, Damien; McVitie, Stephen; Cowburn, Russell; Schumacher, Hans W.; Antonov, Vladimir; Kazakova, Olga
2017-05-01
Devices comprised of CoFeB nanostructures with perpendicular magnetic anisotropy and non-magnetic Ta channel were operated in thermal lateral spin valve (LSV) mode and studied by magnetotransport measurements and magnetic scanning gate microscopy (SGM). Due to the short spin diffusion length of Ta, the spin diffusion signal was suppressed, allowing the study of the contribution from the anomalous Nernst (ANE) and anomalous Hall effects (AHE). The magnetotransport measurements identified the switching fields of the CoFeB nanostructures and demonstrated a combination of AHE and ANE when the devices were operated in thermally-driven spin-injection mode. Modified scanning probe microscopy probes were fabricated by placing a NdFeB magnetic bead (MB) on the apex of a commercial Si probe. The dipole magnetic field distribution around the MB was characterized by using differential phase contrast technique and direct measurement of the switching field induced by the bead in the CoFeB nanodevices. Using SGM we demonstrate the influence of localized magnetic field on the CoFeB nanostructures near the non-magnetic channel. This approach provides a promising route towards the study of thermal and spin diffusion effects using local magnetic fields.
Energy Technology Data Exchange (ETDEWEB)
Matsuura, Yutaka, E-mail: Yutaka_Matsuura@hitachi-metals.co.jp [Hitachi Metals Ltd., NEOMAX Division, 2-15-17 Egawa, Shimamoto-cho, Mishima-gun, Osaka 618-0013 (Japan); Hoshijima, Jun; Ishii, Rintaro [Hitachi Metals Ltd., NEOMAX Division, 2-15-17 Egawa, Shimamoto-cho, Mishima-gun, Osaka 618-0013 (Japan)
2013-06-15
It was found that the coercive force of NdFeB sintered magnets decreases as the Nd{sub 2}Fe{sub 14}B grain alignment improves. Because of this phenomenon, studies looked at the relation between this alignment and the coercive force decrease ratio. In experiments, it was expected that the coercive force of perfectly aligned magnet reached 0.7 of coercive force in istotropically aligned magnet. When it is postulated that the coercive force is determined by the Stoner–Wohlfarth model, coercive force increases as the alignment improves and it becomes difficult to explain our experimental data. On the other hand, when the coercive force is determined by magnetic domain wall motion, the coercive force decreases as the alignment improves and the coercive force of the perfectly aligned magnet reaches 1/√(2) of the isotropically aligned magnet. This tendency and value was very close to our data. It strongly suggests that the coercive force of NdFeB sintered magnets is determined by the domain wall motion. - Highlights: ► Coercive force of NdFeB sintered magnets decreases as grains alignment improves. ► Coercive force decrease ratio reaches −30% at the perfect aligned magnet. ►These experimental results are different from the Stoner–Wohlfarth model. ► The magnetic domain wall motion could explain this coercive force decrease ratio.
Mean field analysis of exchange coupling in amorphous DyFe2-B alloy ribbons
International Nuclear Information System (INIS)
Lee, J.M.; Jung, J.K.; Lim, S.H.
2001-01-01
Experimental magnetization-temperature curves for melt-spun ribbons of amorphous alloys (Dy 0.33 Fe 0.67 ) 1-x B x with x=0, 0.05, 0.1 and 0.15 (in atomic fraction) are fitted with theoretical equations based on the mean field theory in order to investigate exchange couplings between constituent elements as a function of the B content. The sign of the exchange coupling between Dy and Fe is negative, indicating that the magnetization direction of Dy is antiparallel to that of Fe. The sign of the other two couplings are positive. The exchange coupling between Fe ions are greatest, while that between Dy ions is negligible. The exchange couplings between Fe ions, and between Dy and Fe increase with increasing B content, the increase of the latter being much greater than the former. Resulting, the exchange coupling between Dy and Fe becomes about one half of that between Fe ions at the highest B content. The increase of the exchange coupling between Fe ions may be explained by the increase of the Fe-Fe separation with the increase of the B content. The total magnetization is dominated by the Dy sublattice magnetization. As the B content increases, the magnetization decreases over the whole temperature range, and the Curie temperature also decreases
Evolution of Fe environments in mechanically alloyed Fe–Nb–(B) compositions
Energy Technology Data Exchange (ETDEWEB)
Blázquez, J.S., E-mail: jsebas@us.es; Ipus, J.J.; Conde, C.F.; Conde, A.
2014-12-05
Highlights: • Nb is rapidly incorporated to the nanocrystalline FeNb(B) matrix. • B inclusions remains even after long milling times. • B is helpful to enhance the comminuting of crystallites. - Abstract: Nanocrystalline alloys of nominal composition Fe{sub 85}Nb{sub 5}B{sub 10} were produced by mechanical alloying from a mixture of elemental powders. Two commercial boron structures were used: amorphous and crystalline. In addition, a third composition Fe{sub 94.4}Nb{sub 5.6} was prepared for comparison. X-ray diffraction and Mössbauer spectroscopy were used to describe the evolution of the microstructure and Fe environments as a function of the milling time. Whereas Nb is rapidly incorporated into the nanocrystalline matrix, boron inclusions remain even after long milling times. The presence of boron is found to enhance the comminuting of crystallites.
Energy Technology Data Exchange (ETDEWEB)
Batista, S.O.S.; Morales, M.A.; Santos, W.C. dos; Iglesias, C.A. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, 59078-900 Natal, RN (Brazil); Baggio-Saitovitch, E. [Centro Brasileiro de Pesquisas Físicas, Rua Dr. Xavier Sigaud 150, Urca, 22290-180 Rio de Janeiro, RJ (Brazil); Carriço, A.S. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, 59078-900 Natal, RN (Brazil); Bohn, F., E-mail: felipebohn@gmail.com [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, 59078-900 Natal, RN (Brazil); Medeiros, S.N. de [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, 59078-900 Natal, RN (Brazil)
2015-10-01
We report a study of the structural and magnetic properties, as well as of the heat release, of an iron/wüstite composite, prepared from iron powder and water by high energy mechanical milling. We identify that the produced sample consists of α-Fe nanoparticles embedded in a wüstite matrix and has high stability in time. Moreover, we observe that it presents noticeable features, as exchange bias effect at low temperatures and, when an alternating magnetic field is applied, its temperature reaches ∼46 °C in ∼600 s. Thus, the results and the possibility of tuning the magnetic properties of α-Fe nanoparticles embedded in a wüstite matrix, through interface interactions, place this system as a very attractive candidate for biomedical applications such as magnetic hyperthermia agent for cancer therapy. - Highlights: • We investigate the structural and magnetic properties, as well as the heat release, of an iron/wüstite composite. • The samples are produced using high energy mechanical milling. • Fe nanoparticles embedded in a wüstite matrix have high stability in time. • When an alternating magnetic field is applied, the sample temperature increases up to ∼46°C. • The composite is an interesting candidate for biomedical applications, such as magnetic hyperthermia agent for cancer therapy.
Energy Technology Data Exchange (ETDEWEB)
Carneiro, J.F.; Sabioni, A.C.S. [Universidade Federal de Ouro Preto (LDM/DF/UFOP), MG (Brazil). Dept. de Fisica. Lab. de Difusao em Materiais; Trindade, V.B. [Universidade Federal de Ouro Preto (DEMM/UFOP), MG (Brazil). Dept. de Engenharia Metalurgica e de Materiais; Ji, V. [Laboratoire d' Etude des Materiaux Hors-Equilibre (LEMHE), Orsay (France)
2010-07-01
The high temperature oxidation behavior of Fe-1.5%Cr, Fe-5.0%Cr, Fe-10%Cr and Fe- 15%Cr model alloys were investigated from 700 to 850 deg C, in air atmosphere. The oxidation treatments were performed in a thermobalance with a sensitivity of 1{mu}g. The oxide films grown by oxidation of the alloys were characterized by scanning electronic microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The oxide films are Fe-Cr spinels with variable composition depending on the alloy composition. For all conditions studied, the oxidation kinetics of these alloys follow a parabolic law. The comparison of the oxidation rates of the four alloys, at 700 deg C, shows that the parabolic oxidation constants decrease from 1.96x10{sup -9}g{sup 2}.cm{sup -4}.s{sup -1}, for the alloy Fe-1.5% Cr, to 1.18 x 10-14g{sup 2}.cm{sup -4}.s{sup -1} for the alloy Fe-15% Cr. Comparative analysis of the oxidation behavior of the Fe-10%Cr and Fe-15%Cr alloys, between 700 and 850 deg C, shows that the oxidation rates of these alloys are comparable to 800 deg C, above this temperature the Fe-10%Cr alloy shows lower resistance to oxidation. (author)
Energy Technology Data Exchange (ETDEWEB)
Li Jun [School of Materials Science and Engineering, Sichuan University, Chengdu 610065 (China); Liu Ying, E-mail: Liuying5536@163.com [School of Materials Science and Engineering, Sichuan University, Chengdu 610065 (China) and Key Laboratory of Advanced Special Material and Technology, Ministry of Education, Chengdu 610065 (China); Ma Yilong [School of Materials Science and Engineering, Sichuan University, Chengdu 610065 (China)
2012-07-15
Bulk anisotropic NdFeB/{alpha}-Fe nano-composites were obtained directly from alloys of Nd{sub 11}Dy{sub 0.5}Fe{sub 82.4-x}Nb{sub x}B{sub 6.1} (x=0,0.5,1.0,1.5). High resolution transmission electron microscopy images showed the existence of Nb-rich amorphous grain boundary phase in the alloys with Nb doped. Field emission scanning electron microscope morphologies and X-ray diffraction patterns revealed the grain size and grain alignment of hot pressed and hot deformed nanocomposites. It was found that Nb could refine the grain size and grain texture in hot worked ribbons. Vibrating sample magnetometer results showed that the magnetic properties of the anisotropic nanocomposites were improved with increased Nb doping. The remanence, coercivity and maximum energy product of the bulk anisotropic Nd{sub 11}Dy{sub 0.5}Fe{sub 80.4}Nb{sub 2}B{sub 6.1} nanocomposites were 1.04 T, 563 kA/m and 146 kJ/m{sup 3}, respectively. - Highlights: Black-Right-Pointing-Pointer Nb has great influence on the microstructure and magnetic properties of (NdDy){sub 11.5}Fe{sub 82.4-x}Nb{sub x}B{sub 6.1} (x=0-2.0) nanocomposites. Black-Right-Pointing-Pointer Most of Nb atoms gather in the grain boundary to form Nb-rich amorphous intergranular phase, not NbFeB boride. Black-Right-Pointing-Pointer Furthermore, grain alignment can be prompt by the Nb-rich solid intergranular phase during deform. Black-Right-Pointing-Pointer Remanence, coercivity and (BH){sub m} of deformed (NdDy){sub 11.5}Fe{sub 80.4}Nb{sub 2}B{sub 6.1} nanocomposite is 1.04T, 563 kA/m and 146 kJ/m{sup 3} respectively. Black-Right-Pointing-Pointer This study provides an alternative method for prepare anisotropic nanocomposite direct from Nd-lean alloys with low cost.
Development of FeCoB/Graphene Oxide based microwave absorbing materials for X-Band region
International Nuclear Information System (INIS)
Das, Sukanta; Chandra Nayak, Ganesh; Sahu, S.K.; Oraon, Ramesh
2015-01-01
This work explored the microwave absorption capability of Graphene Oxide and Graphene Oxide coated with FeCoB for stealth technology. Epoxy based microwave absorbing materials were prepared with 30% loading of Graphene Oxide, FeCoB alloy and Graphene Oxide coated with FeCoB. Graphene Oxide and FeCoB were synthesized by Hummer's and Co-precipitation methods, respectively. The filler particles were characterized by FESEM, XRD and Vibrating Sample Magnetometer techniques. Permittivity, permeability and reflection loss values of the composite absorbers were measured with vector network analyzer which showed a reflection loss value of −7.86 dB, at 10.72 GHz, for single layered Graphene Oxide/Epoxy based microwave absorbers which can be correlated to the absorption of about 83.97% of the incident microwave energy. Reflection loss value of FeCoB/Epoxy based microwave absorber showed −13.30 dB at 11.67 GHz, which corresponded to maximum absorption of 93.8%. However, reflection loss values of Graphene Oxide coated with FeCoB/Epoxy based single-layer absorber increased to −22.24 dB at 12.4 GHz which corresponds to an absorption of 99% of the incident microwave energy. - Highlights: • FeCoB coated Graphene Oxide (GO) was synthesized by co-precipitation method. • GO, FeCoB and GO@FeCoB based microwave absorbers were developed with Epoxy matrix. • GO and FeCoB/Epoxy absorbers showed −7.86 & −13.30 dB reflection loss, respectively. • Maximum Reflection loss of −22.24 dB was achieved with GO@FeCoB/Epoxy absorber
Microstructure and Magnetic Properties of NdFeB Films through Nd Surface Diffusion Process
Liu, Wenfeng; Zhang, Mingang; Zhang, Kewei; Chai, Yuesheng
2017-01-01
Ta/Nd/NdFeB/Nd/Ta films were deposited by magnetron sputtering on Si (100) substrates and subsequently annealed for 30 min at 923 K in vacuum. It was found that the microstructure and magnetic properties of Ta/Nd/NdFeB/Nd/Ta films strongly depend on the NdFeB layer thickness. With NdFeB layer thickness increasing, both the grain size and the strain firstly reduce and then increase. When NdFeB layer thickness is 750 nm, the strain reaches the minimum value. Meanwhile, both the in-plane and per...
Wang, Li Kai; Zhu, Hui; Shuman, Stewart
2009-03-27
NAD(+)-dependent DNA ligases (LigA) are ubiquitous in bacteria, where they are essential for growth and present attractive targets for antimicrobial drug discovery. LigA has a distinctive modular structure in which a nucleotidyltransferase catalytic domain is flanked by an upstream NMN-binding module and by downstream OB-fold, zinc finger, helix-hairpin-helix, and BRCT domains. Here we conducted a structure-function analysis of the nucleotidyltransferase domain of Escherichia coli LigA, guided by the crystal structure of the LigA-DNA-adenylate intermediate. We tested the effects of 29 alanine and conservative mutations at 15 amino acids on ligase activity in vitro and in vivo. We thereby identified essential functional groups that coordinate the reactive phosphates (Arg(136)), contact the AMP adenine (Lys(290)), engage the phosphodiester backbone flanking the nick (Arg(218), Arg(308), Arg(97) plus Arg(101)), or stabilize the active domain fold (Arg(171)). Finer analysis of the mutational effects revealed step-specific functions for Arg(136), which is essential for the reaction of LigA with NAD(+) to form the covalent ligase-AMP intermediate (step 1) and for the transfer of AMP to the nick 5'-PO(4) to form the DNA-adenylate intermediate (step 2) but is dispensable for phosphodiester formation at a preadenylylated nick (step 3).
Characteristics of magnetic tunnel junctions comprising ferromagnetic amorphous NiFeSiB layers
International Nuclear Information System (INIS)
Chun, B.S.; Kim, Y.K.; Hwang, J.Y.; Yim, H.I.; Rhee, J.R.; Kim, T.W.
2007-01-01
Magnetic tunnel junctions (MTJs), which consisted of amorphous ferromagnetic Ni 16 Fe 62 Si 8 B 14 free layers, were investigated. NiFeSiB has a lower saturation magnetization (M s : 800 emu/cm 3 ) than Co 90 Fe 10 and a higher anisotropy constant (K u : 2700 erg/cm 3 ) than Ni 80 Fe 20 . By increasing the free layer thickness, the tunnel magnetoresistance (TMR) ratio of up to 41% was achieved and it exhibited a much lower switching field (H sw ) than the conventionally used CoFe free layer MTJ. Furthermore, by inserting a thin CoFe layer (1 nm) at the tunnel barrier/NiFeSiB interface, the TMR ratio and switching squareness were enhanced
Magnetic viscosity and coercivity mechanisms in sintered and melt spun NdFeB
International Nuclear Information System (INIS)
Street, R.; Bingham, D.; Day, R.K.; Dunlop, J.B.
1988-01-01
Magnetic viscosity parameters kT/q(=Sv) of sintered and melt spun NdFeB vary with internal field. During initial magnetization of thermally demagnetized specimens signifiant viscosity occurs with melt spun NdFeB but is negligible with sintered NdFeB. Differences in mechanisms of magnetization account for this behaviour
Energy Technology Data Exchange (ETDEWEB)
Gabriel, A.H.G.; Ananias, M.Jr. da S.; Lucena, F.A.; Santos, L.S. dos; Bolfarini, C.; Botta, W.J.; Kiminami, C.S.; Afonso, C.R.M., E-mail: guimaraes.andreh@gmail.com [Universidade Federal de Sao Carlos (UFSCar), Sao Carlos, SP (Brazil)
2014-07-01
Iron-based amorphous alloys show outstanding characteristics such as high hardness and wear resistance, with microstructure partially amorphous, making them favorable to spray forming process (SF), which has cooling rates between 10{sup 3}-10{sup 5} K/s. Thus, this work aims to use the SF in one of the alloy cast iron present in this project, being chosen the alloy with a better set of results, through the performed characterizations. The alloys studied in this project were: (Fe{sub 65}Cr{sub 17}Mo{sub 2}C{sub 14}Si{sub 1}Cu{sub 1}){sub 100-x}B{sub x} (x = 5, 8 and 12% at) and (Fe{sub 65}Cr{sub 17}Mo{sub 2}C{sub 14}Si{sub 1}Cu{sub 1}){sub 88}Nb{sub 4}B{sub 8} (at.%), being all processed through Discovery® Plasma and 'melt- spinning' and characterized using: TEM, SEM, DSC, XRD and microhardness test. The cast iron alloy selected were (Fe{sub 65}Cr{sub 17}Mo{sub 2}C{sub 14}Si{sub 1}Cu{sub 1}){sub 88}Nb{sub 4}B+8, getting by the spray forming process, deposit and overspray powder. With them, were realized almost the same characterizations, except for the TEM. The results showed 1044±102 (HV1) in Vickers microhardness and nanocrystalline overspray powder from 20-45 μm to > 180 μm. (author)
Crystallization behavior and magnetic properties in High Fe content FeBCSiCu alloy system
Energy Technology Data Exchange (ETDEWEB)
Fan, X.D., E-mail: fanxd@seu.edu.cn; Shen, B.L., E-mail: blshen@seu.edu.cn
2015-07-01
High Fe content FeBCSiCu nanocrystalline alloys are prepared by annealing melt-spun amorphous ribbons with aim at increasing saturation magnetic flux density. Microstructures identified by XRD and TEM reveal that Cu addition inhibits the surface crystallization of Fe{sub 86}B{sub 7}C{sub 7} alloy and improve its glass-forming ability. Activation energy of crystallization calculated by Kissinger's equation indicates that both Cu and Si addition promotes the precipitation of α-Fe phase and improves the thermal stability. VSM and DC B–H loop tracer measurements show that the Fe{sub 85.5}B{sub 7}C{sub 6}Si{sub 1}Cu{sub 0.5} nanocrystalline alloy exhibits high saturation magnetic flux density of 1.8 T and low coercivity of 10 A/m, respectively. AC properties measured by AC B–H analyzer show this alloy exhibits low core loss of 0.35 W/kg at 1 T at 50 Hz. Low material cost and convenient productivity make the Fe{sub 85.5}B{sub 7}C{sub 6}Si{sub 1}Cu{sub 0.5} nanocrystalline alloy an economical application in industry. - Highlights: • Cu addition inhibits the surface crystallization and improves the GFA. • The competitive formation of Fe{sub 3}C and α-Fe phase impedes the devitrification. • Fe{sub 85.5}B{sub 7}C{sub 6}Si{sub 1}Cu{sub 0.5} nanocrystalline alloy exhibits excellent magnetic properties. • The alloy system has an economical advantage and convenient productivity.
Nanocrystallization in amorphous Fe40Ni40(Si+B)19Mo1-2 ribbons
International Nuclear Information System (INIS)
Saiseng, S.; Winotai, P.; Nilpairuch, S.; Limsuwan, P.; Tang, I.M.
2004-01-01
Cut Fe 40 Ni 40 (Si+B) 19 Mo 1-2 ribbons were annealed for 2 h at various temperatures between 350 deg. C and 600 deg. C. XRD and Mossbauer effect spectroscopy (ME) measurements were then performed on all of the ribbons. The magnetic properties of several ribbons were measured using a vibrating sample magnetometer (VSM). A differential thermal analysis scan (over the range 20-800 deg. C) of the as-cast ribbon showed two phase transitions; the first at 454 deg. C and the second at 525 deg. C. Both the XRD and ME spectra of the as cast, the 350 deg. C and 400 deg. C annealed ribbons showed that they were amorphous. The ME spectra of the 450 deg. C, 475 deg. C and 500 deg. C annealed ribbons showed that these ribbons contained α-Fe, α-Fe(Si) and t-Fe 2 B nanocrystallites. For the ribbons annealed above 550 deg. C, crystallites of t-Fe 2 B, t-Fe 3 B, t-Fe 5 SiB 2 and FCC-FeNi appeared, with the α-Fe and α-Fe(Si) crystallites disappearing. The sextets of all of the Fe compounds appeared in the ME spectra of the 525 deg. C annealed ribbon. The VSM measurements supported the picture of a two-stage phase transitions; amorphous phase→a nanocrystalline phase (Fe-containing nanocrystallites in an amorphous matrix) at 454 deg. C and then a second transition, the nanocrystalline phase→a disordered alloy containing Fe-B and Fe-Ni crystallites at 525 deg. C
Observation of Pseudopartial Grain Boundary Wetting in the NdFeB-Based Alloy
Straumal, B. B.; Mazilkin, A. A.; Protasova, S. G.; Schütz, G.; Straumal, A. B.; Baretzky, B.
2016-08-01
The NdFeB-based alloys were invented in 1980s and remain the best-known hard magnetic alloys. In order to reach the optimum magnetic properties, the grains of hard magnetic Nd2Fe14B phase have to be isolated from one another by the (possibly thin) layers of a non-ferromagnetic Nd-rich phase. In this work, we observe that the few-nanometer-thin layers of the Nd-rich phase appear between Nd2Fe14B grains due to the pseudopartial grain boundary (GB) wetting. Namely, some Nd2Fe14B/Nd2Fe14B GBs are not completely wetted by the Nd-rich melt and have the high contact angle with the liquid phase and, nevertheless, contain the 2-4-nm-thin uniform Nd-rich layer.
International Nuclear Information System (INIS)
Chaboy, J.; Marcelli, A.; Garcia, L.M.; Bartolome, J.; Kuz'min, M.D.; Maruyama, H.; Kobayashi, K.; Kawata, H.; Iwazumi, T.
1995-01-01
We present the first experimental observation of spin reorientation phase transitions (SRT) with the X-Ray circular magnetic dichroism (XCMD) technique. Both the first-order SRT in Er 2 Fe 14 B and the second-order one in Nd 2 Fe 14 B have been clearly detected, demonstrating the feasibility of this technique for studying SRTs. ((orig.))
Iacovacci, V; Lucarini, G; Innocenti, C; Comisso, N; Dario, P; Ricotti, L; Menciassi, A
2015-12-01
This work reports the fabrication, magnetic characterization and controlled navigation of film-shaped microrobots consisting of a polydimethylsiloxane-NdFeB powder composite material. The fabrication process relies on spin-coating deposition, powder orientation and permanent magnetization. Films with different powder concentrations (10 %, 30 %, 50 % and 70 % w/w) were fabricated and characterized in terms of magnetic properties and magnetic navigation performances (by exploiting an electromagnet-based platform). Standardized data are provided, thus enabling the exploitation of these composite materials in a wide range of applications, from MEMS/microrobot development to biomedical systems. Finally, the possibility to microfabricate free-standing polymeric structures and the biocompatibility of the proposed composite materials is demonstrated.
NdFeB magnets with zero temperature coefficient of induction
International Nuclear Information System (INIS)
Ma, B.M.; Narasimhan, K.S.V.L.; Hurt, J.C.
1986-01-01
Temperature compensation for the induction of NdFeB type magnets has been investigated. A computer assisted alloy selection method was adopted to identify composition of zero temperature coefficient of induction over -50 to 200 0 C. Selected alloys were processed into magnet by the conventional powder metallurgy method. The experimental temperature coefficient on the sintered magnet correlated with the prediction satisfactory. Holmium is an essential ingredient required for temperature compensation of NdFeB magnets. A magnet, (Nd/sub 0.23/Ho/sub 0.64/Dy/sub 0.13/)/sub 15/Fe/sub 79/B/sub 6/ with B/sub r/ of 7,700 Gauss, H/sub c/ of 7,700 Oe, H/sub ci/ of 20,600 Oe, Bh/sub max/ of 14.8 MGOe and temperature coefficient of -0.029% per 0 C over -50 to +150 was obtained
Coercivity enhancement in Ce-Fe-B based magnets by core-shell grain structuring
Directory of Open Access Journals (Sweden)
M. Ito
2016-05-01
Full Text Available Ce-based R2Fe14B (R= rare-earth nano-structured permanent magnets consisting of (Ce,Nd2Fe14B core-shell grains separated by a non-magnetic grain boundary phase, in which the relative amount of Nd to Ce is higher in the shell of the magnetic grain than in its core, were fabricated by Nd-Cu infiltration into (Ce,Nd2Fe14B hot-deformed magnets. The coercivity values of infiltrated core-shell structured magnets are superior to those of as-hot-deformed magnets with the same overall Nd content. This is attributed to the higher value of magnetocrystalline anisotropy of the shell phase in the core-shell structured infiltrated magnets compared to the homogeneous R2Fe14B grains of the as-hot-deformed magnets, and to magnetic isolation of R2Fe14B grains by the infiltrated grain boundary phase. First order reversal curve (FORC diagrams suggest that the higher anisotropy shell suppresses initial magnetization reversal at the edges and corners of the R2Fe14B grains.
Effect of borohydride addition rate on chemically prepared amorphous Fe-B particles
International Nuclear Information System (INIS)
Koch, C.B.; Morup, S.; Linderoth, S.
1991-01-01
Amorphous Fe-B alloys can be prepared by reacting aqueous solutions of Fe salts and NaBH 4 . In this paper the effect of the addition rate of the NaBH 4 solution to the FeSO 4 solution on the precipitate is investigated. The chemical composition of the amorphous alloys formed varies between Fe 79 B 21 and Fe 68 B 32 . The hyperfine parameters of the alloys, derived from Mossbauer spectra, show a decrease from 29 to 25 T of the magnetic hyperfine field and an increase from 0.19 to 0.28 mms -1 of the isomer shift with increasing NaBH 4 addition rate. The results suggest that alloys with different structures but identical composition may be produced by chemical reduction
Intrinsic evolution of novel (Nd, MM)2Fe14B-system magnetic flakes
Yu, Xiaoqiang; Zhu, Minggang; Liu, Weiqiang; Li, Yanfeng; Zhang, Jiuxing; Yue, Ming; Li, Wei
2018-01-01
The Nd-substituted (Nd x MM1- x )-Fe-B strip-casting flakes were prepared by induction melting in the vacuum furnace and then subsequently by strip-casting technology. The microstructure and magnetic properties of (Nd x MM1- x )-Fe-B alloys are related to the Nd substitution. 2:14:1 main phases and minor impure phases coexist in the MM-Fe-B flake. For example, La2O3 and CeFe2 impure phases are obviously detected in the x = 0 specimen. As an increase of the Ce concentration is inversely accompanied with the decrease of the Nd content ( x) in (Nd x MM1- x )2Fe14B main phases (0 ≤ x ≤ 1), XRD analysis shows that the overall diffraction peaks of the main phases shift to right domestically because of smaller radius Ce4+. The melting point, spin reorientation phase transition temperature, Curie temperature, magneto-crystalline anisotropy field (at 300 K), and the magnetization ( M 9T) for MM-Fe-B/(Nd0.4MM0.6)-Fe-B/(Nd0.7MM0.3)-Fe-B/Nd-Fe-B strip-casting alloys are 1376.15/1414.15/1439.15/1458.15 K, 74/113/124/135 K, 493.2/538.4/559.7/582.3 K, 48/55.2/64.4/70.1 kOe and 136.5/143.7/151.5/153.7 emu/g, respectively. Due to the varied composition of hard magnetic main phases, M 9T increases gradually with the increase of Nd content ( x). SEM observation and EDX results demonstrate that more Nd and Pr elements aggregate into the 2:14:1 ferromagnetic phase, while less La and Ce elements are prone to the RE-rich region compared with the nominal ratio. As a result, the growth of M 9T becomes extraordinary under maximum external field 9 T, indicating that the (Nd0.7MM0.3)-Fe-B flake may display relatively good magnetic properties and those with higher Nd content have evident effect on magnetization, compositions, and microstructures of hard magnetic main phases. Therefore, practical application of (Nd x MM1- x )-Fe-B-sintered magnets will be very prospective.
Magnetic properties and thermal stability of MnBi/NdFeB hybrid bonded magnets
International Nuclear Information System (INIS)
Cao, S.; Yue, M.; Yang, Y. X.; Zhang, D. T.; Liu, W. Q.; Zhang, J. X.; Guo, Z. H.; Li, W.
2011-01-01
Magnetic properties and thermal stability were investigated for the MnBi/NdFeB (MnBi = 0, 20, 40, 60, 80, and 100 wt.%) bonded hybrid magnets prepared by spark plasma sintering (SPS) technique. Effect of MnBi content on the magnetic properties of the hybrid magnets was studied. With increasing MnBi content, the coercivity of the MnBi/NdFeB hybrid magnets increases rapidly, while the remanence and maximum energy product drops simultaneously. Thermal stability measurement on MnBi magnet, NdFeB magnet, and the hybrid magnet with 20 wt.% MnBi indicates that both the NdFeB magnet and the MnBi/NdFeB hybrid magnet have a negative temperature coefficient of coercivity, while the MnBi magnet has a positive one. The (BH) max of the MnBi/NdFeB magnet (MnBi = 20 wt.%) is 5.71 MGOe at 423 K, which is much higher than 3.67 MGOe of the NdFeB magnet, indicating a remarkable improvement of thermal stability.
Wear resistance of TiB/sub 2/-Fe cermets
International Nuclear Information System (INIS)
Champagne, B.; Dallaire, S.
1985-01-01
A material which consists of TiB/sub 2/ dispersed in an iron matrix was synthesized by the exothermic reaction of ferrotitanium and boron. The as-reacted products were hot isostatically pressed to produce TiB/sub 2/-Fe cermets. The influence of HIP variables on the density and total fractional porosity of specimens is presented. Density above 95% is obtained by HIPping at temperatures below 1300 0 C. Increasing the temperature and the time of HIPping enhance the mechanical properties and wear resistance of TiB/sub 2/-Fe cermets by reducing their residual porosity. Relations obtained by regression analysis showed that the porosity strongly affects the properties of parts. Regression analysis point out that the wear loss of a 5% porosity TiB/sub 2/-Fe cermet is 270% higher than a dense HIPped cermet. Low stress and high stress abrasion resistance tests utilizing various abrasive media were carried out on dense HIPped cermets and results were compared with those obtained from WC-Co cermets and 1020 steel
Long-term results using LigaSure™ 5 mm instrument for treatment of Zenker's diverticulum
DEFF Research Database (Denmark)
Andersen, Michelle Fog; Trolle, Waldemar; Anthonsen, Kristian
2017-01-01
The purpose of the present study was to evaluate the long-term results and patient's satisfaction of a new approach using the LigaSure™ 5 mm instrument for treatment of Zenker's diverticulum (ZD) and to compare with other long-term results using traditional treatment modalities. Between December ...... to traditional endoscopic techniques and is now the standard treatment method for ZD in our departments.......The purpose of the present study was to evaluate the long-term results and patient's satisfaction of a new approach using the LigaSure™ 5 mm instrument for treatment of Zenker's diverticulum (ZD) and to compare with other long-term results using traditional treatment modalities. Between December......%) reported no symptoms at all. Our results suggest that endoscopic management of ZD with the LigaSure™ 5 mm instrument is a minimally invasive, fast and safe method with solid long-term outcome with relief of symptoms and patient satisfaction. This new operative instrument was not found inferior...
Magnetic properties of ND Rich Melt-Spun ND-FE-B alloy
Directory of Open Access Journals (Sweden)
Grujić Aleksandar
2005-01-01
Full Text Available As a part of these experimental investigations of melt-spun Nd-Fe-B alloy with Nd rich content in relation to Nd2Fe14B prepared by rapid quenching process for optimally selected cooling rate and heat treatment, the influence of the chosen chemical composition on magnetic properties was observed. The results of X-ray diffraction, Mössbauer spectroscopy phase analysis and magnetic measurement of investigated melt-spun Nd14.5Fe78.5B7 alloy are presented to bring some new information concerning the relation between their structure and magnetic properties.
A route for recycling Nd from Nd-Fe-B magnets using Cu melts
Energy Technology Data Exchange (ETDEWEB)
Moore, Martina; Gebert, Annett, E-mail: a.gebert@ifw-dresden.de; Stoica, Mihai; Uhlemann, Margitta; Löser, Wolfgang
2015-10-25
Phase evolutions in Nd-Fe-B magnet/Cu systems have been explored with regard to Nd recycling. It was demonstrated that large scale phase separation into a ferromagnetic Fe(B)-rich ingot core with α-Fe main phase and a non-magnetic (Cu,Nd)-rich ingot rim takes place upon arc melting with Cu fractions ≥ 21.5 wt.-%. The re-solidification of the Nd{sub 2}Fe{sub 14}B magnet main phase is suppressed. The rim consists of the Cu{sub 2}Nd main phase and CuNd/Cu{sub 4}Nd minority phases in which Al traces from the magnetic material are gathered. Induction melting of such Nd-Fe-B/Cu mixtures can support the separation of these phase regions with very sharp boundaries. Main features of liquid phase separation and microstructure evolution have been interpreted on the basis of Nd-Fe-Cu phase diagram data. The key advantage with respect to Nd recycling from Nd-Fe-B permanent magnet scrap is the substantial accumulation of Nd in the (Cu,Nd)-rich region of the phase separated solidified specimen, which can be easily detached from the Fe-rich part by mechanical-magnetic treatments. Such portions contained up to ∼44 wt.-% Nd (25 at.-%) in first lab-scale experiments. Nd recovery from the (Cu,Nd)-rich fractions is possible by exploiting the large chemical property differences between the reactive rare earths elements and Cu. - Highlights: • phase evolution analysis in Nd-Fe-B magnet/Cu systems with regard to Nd recycling. • Cu ≥ 21 wt.-%, large scale phase separation- Fe(B)-rich ingot core, (Cu,Nd)-rich rim. • high Nd content (∼44 wt.-%) of (Cu,Nd)-rich region, mechanical-magnetic treatments.
Development of FeNiMoB thin film materials for microfabricated magnetoelastic sensors
Liang, Cai; Gooneratne, Chinthaka; Cha, Dong Kyu; Chen, Long; Gianchandani, Yogesh; Kosel, Jü rgen
2012-01-01
MetglasTM 2826MB foils of 25–30 μm thickness with the composition of Fe40Ni38Mo4B18 have been used for magnetoelastic sensors in various applications over many years. This work is directed at the investigation of ∼3 μm thick iron-nickel-molybdenum-boron (FeNiMoB) thin films that are intended for integrated microsystems. The films are deposited on Si substrate by co-sputtering of iron-nickel (FeNi), molybdenum(Mo), and boron (B) targets. The results show that dopants of Mo and B can significantly change the microstructure and magnetic properties of FeNi materials. When FeNi is doped with only Mo its crystal structure changes from polycrystalline to amorphous with the increase of dopant concentration; the transition point is found at about 10 at. % of Mo content. A significant change in anisotropic magneticproperties of FeNi is also observed as the Modopant level increases. The coercivity of FeNi filmsdoped with Mo decreases to a value less than one third of the value without dopant.Doping the FeNi with B together with Mo considerably decreases the value of coercivity and the out-of-plane magnetic anisotropyproperties, and it also greatly changes the microstructure of the material. In addition, doping B to FeNiMo remarkably reduces the remanence of the material. The filmmaterial that is fabricated using an optimized process is magnetically as soft as amorphous MetglasTM 2826MB with a coercivity of less than 40 Am−1. The findings of this study provide us a better understanding of the effects of the compositions and microstructure of FeNiMoB thin filmmaterials on their magnetic properties.
Development of FeNiMoB thin film materials for microfabricated magnetoelastic sensors
Liang, Cai
2012-12-07
MetglasTM 2826MB foils of 25–30 μm thickness with the composition of Fe40Ni38Mo4B18 have been used for magnetoelastic sensors in various applications over many years. This work is directed at the investigation of ∼3 μm thick iron-nickel-molybdenum-boron (FeNiMoB) thin films that are intended for integrated microsystems. The films are deposited on Si substrate by co-sputtering of iron-nickel (FeNi), molybdenum(Mo), and boron (B) targets. The results show that dopants of Mo and B can significantly change the microstructure and magnetic properties of FeNi materials. When FeNi is doped with only Mo its crystal structure changes from polycrystalline to amorphous with the increase of dopant concentration; the transition point is found at about 10 at. % of Mo content. A significant change in anisotropic magneticproperties of FeNi is also observed as the Modopant level increases. The coercivity of FeNi filmsdoped with Mo decreases to a value less than one third of the value without dopant.Doping the FeNi with B together with Mo considerably decreases the value of coercivity and the out-of-plane magnetic anisotropyproperties, and it also greatly changes the microstructure of the material. In addition, doping B to FeNiMo remarkably reduces the remanence of the material. The filmmaterial that is fabricated using an optimized process is magnetically as soft as amorphous MetglasTM 2826MB with a coercivity of less than 40 Am−1. The findings of this study provide us a better understanding of the effects of the compositions and microstructure of FeNiMoB thin filmmaterials on their magnetic properties.
Directory of Open Access Journals (Sweden)
Cibele Andrucioli de Mattos Pimenta
1998-10-01
Full Text Available Os objetivos deste estudo foram descrever um programa extracurricular de educação em dor, organizado na forma de Liga, e identificar a opinião dos alunos sobre esse modelo de ensino. O Estatuto e o Regimento Interno da Liga de Dor foram as fontes e dados para a descrição da sua organização e funcionamento. Todos os alunos que frequentaram a Liga de Dor nos anos de 1995 e 1996 foram solicitados a responder um questionário sobre suas experiências na Liga. A Liga de Dor foi organizada sob o patrocínio do Centro Acadêmico Osvaldo Cruz, da Faculdade de Medicina da USP, e Centro Acadêmico XXXI de Outubro, da Escola de Enfermagem da USP, em 1995. É composta por alunos dessas duas faculdades e profissionais enfermeiros e médicos, de várias especialidades. Todas as atividades são voluntárias, desenvolvidas em período extracurricular e os estudantes dirigem a Liga. Os objetivos da Liga são: melhorar a qualidade do ensino sobre dor nas escolas médica e de enfermagem, desenvolver pesquisas relativas à epidemiologia, clínica e controle da dor e promover modelo de assistência multidisciplinar e multiprofissional. A maioria dos alunos expressou ter alcançado seus objetivos, total ou parcialmente; ter aumentado seu conhecimento sobre as síndromes álgicas e sobre o manejo do doente com dor; sentir-se gratificado com sua atividade; que o tema dor deveria ser incluído no currículo de modo mais específico e que recomendaria a outros colegas a participação na Liga de Dor. As opiniões dos estudantes mostraram que a Liga de Dor pode ser um modelo útil para a introdução do ensino da dor nos cursos de graduação e enfermagem e de medicina.Although anatomical and physiological base of pain are subject of the basic sciences in health undergraduate curriculum, it is not usually to have pain, concepts and therapy into undergraduate programs. Describing the League Against Pain objectives and organization and the students' opinions about
Crystallization of the amorphous Fe80Zr12B8 alloy under controlled heating
International Nuclear Information System (INIS)
Huang, H.; Shao, G.; Tsakiropoulos, P.
2008-01-01
The devitrification process of amorphous Fe 80 Zr 12 B 8 alloy ribbons were studied under controlled thermal conditions. The major crystallization event during continuous heating with differential scanning calorimetory (DSC) is dictated by diffusion controlled growth and the associated atom mobility of the slow diffusing species Zr. The existence of prior nano-crystals formed by pre-annealing below the crystallization temperature had little effect on the major crystallization temperature. The crystallization sequence during heating was: amorphous → amorphous + α-Fe + Fe 3 Zr(B) → amorphous + α-Fe + Fe 3 Zr(B) + Fe 2 Zr. Different from previous findings in alloys of lower Zr and B contents, the peak for the crystallization of the α-Fe phase alone is missing in the DSC traces of this alloy
Magnetic properties of nanocrystallized Fe-Pt-B melt-spun ribbons
International Nuclear Information System (INIS)
Yamamoto, Tokujiro; Omori, Akihiro; Kimura, Hisamichi; Inoue, Akihisa
2007-01-01
L1 0 FePt nanoparticles have been prepared by etching grain boundaries of heat-treated melt-spun Fe-19Pt-25B (at.%) alloy ribbons. It is revealed that an L1 0 FePt nanocrystalline phase is directly formed from the Fe-Pt-B amorphous ribbons by long-time heat treatment at low temperatures in the vicinity of 723 K. With increasing heat treatment time, dimensions of the nanocrystallized FePt grains increase, accompanied by a change from soft ferromagnetic to hard ferromagnetic. The ribbon crystallized at 723 K for 1.8 ks consists of only an FePt L1 0 phase and its coercivity is as low as 0.381 kA/m. However, it increases to 372 kA/m with increasing grain size of precipitated L1 0 phase to about 30 nm by heat treatment for 86.4 ks, while the saturation magnetic flux density remains constant at about 0.4 T. Etching boundaries in heat-treated ribbons has been performed to obtain ferromagnetic L1 0 FePt nanoparticles and several particles were observed by means of transmission electron microscopy
Directory of Open Access Journals (Sweden)
Eduardo André Alberti
2015-06-01
Full Text Available ResumoA manufatura aditiva é um processo utilizado para a construção e reparos de peças que possuem geometria complexa ou que necessitem de gradiente de propriedades. Nessa técnica múltiplas camadas são depositadas para a construção da geometria do componente. O sucesso desse procedimento depende de fatores como a técnica de deposição, parâmetros, liga a ser depositada e condições da deposição, como temperatura e atmosfera protetora. Neste estudo, o potencial da técnica de Plasma por arco transferido para manufatura aditiva foi avaliado produzindo “paredes finas”, construídas a partir da sobreposição de cordões. Foram utilizadas duas ligas a base de níquel, uma endurecida por precipitação e outra endurecida por solução sólida. Durante os trabalhos, foram selecionados os parâmetros de processamentos, incluindo a avaliação do efeito do pré-aquecimento a 300°C. Resultados mostraram que a composição química da liga influencia a geometria da parede construída assim como a utilização de pré-aquecimento. Estruturas de solidificação exibindo dendritas refinadas com crescimento epitaxial entre camadas são identificadas. Entretanto, as características da liga determinam o perfil de dureza ao longo da seção transversal, sendo a liga endurecida por precipitação influenciada pelos ciclos térmicos de deposição e a liga endurecida por solução sólida pela diluição com o substrato. Em qualquer dos casos é recomendado a aplicação de tratamento térmico pós-soldagem para uniformização das propriedades.
Energy Technology Data Exchange (ETDEWEB)
Janasi, S.R.; Rodrigues, D.; Landgraf, F.J.G. [Instituto de Pesquisas Tecnologicas (IPT), Sao Paulo, SP (Brazil). Lab. de Metalurgia e Materiais Ceramicos; Silva, B.F.A. da; Takiishi, H [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Campos, M.F. de [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil)
2010-07-01
The production of NdFeB powders by the HDDR process from metallic alloys has been widely investigated. Different HD and DR conditions have been used to induce anisotropy and to improve the intrinsic coercivity of the obtained powders. The purpose of this study is to apply the HDDR process in the reprocessing of NdFeB sintered magnet scraps. There were investigated different processing conditions as temperature and time of desorption and recombination (DR). The results of X ray diffraction show the formation of the magnetic phase Nd{sub 2}Fe{sub 14}B in all the investigated conditions. Magnetic measurements by vibrating sample magnetometer indicate that powders with intrinsic coercivity up to 790 kA/m were obtained. (author)
Directory of Open Access Journals (Sweden)
Vinícius Toledo Saccon
2010-12-01
Full Text Available Este trabalho visou analisar a caracterização microestrutural e o comportamento mecânico das ligas de alumínio AA2139 T3 e T8 quando são soldadas pelo processo Soldagem por Fricção Rotativa com Mistura, o qual é realizado na fase sólida. A análise microestrutural foi realizada utilizando microscopia óptica e eletrônica de varredura, e o comportamento mecânico foi avaliado através de medidas de microdureza e ensaio de tração convencional complementado pelo sistema ARAMIS. As ligas foram soldadas nos mesmos parâmetros de soldagem e com a mesma ferramenta, a fim de avaliar a qualidade da junta soldada para as duas condições de tratamento térmico, T3 e T8. Os resultados obtidos mostraram soldas resistentes para ambos os tratamentos térmicos, porém com melhores propriedades mecânicas para a liga AA2139 T3.This work aimed to study the microstructural characterization and mechanical behavior of AA2139 T3 and T8 aluminum alloys joined by FSW - Friction Stir Welding. The microstructural analysis has been done using optical microscope and scanning electron microscopy, and the mechanical analysis were evaluate through microhardness testing and conventional tensile test using the ARAMIS system . Each alloy were welded using the same welding parameters and the same tool in order to evaluate the joint quality for both heat treatment used for this work, T3 and T8. The result showed sounds joints for both heat treatments, although with better mechanical properties for the alloy AA2139 T3.
Energy Technology Data Exchange (ETDEWEB)
Jeon, Min Ku; Lee, Ki Rak; Kang, Kweon Ho; Park, Geun Il [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Jeon, Hyung Joon [Kyoto University, Kyoto (Japan); McGinn, Paul J. [University of Notre Dame, Indiana (United States)
2015-02-15
Quaternary Pt{sub 2}Ru{sub 1}Fe{sub 1}M{sub 1}/C (M=Ni, Mo, or W) catalysts were investigated for the methanol electro-oxidation reaction (MOR). Electrocatalytic activities of the quaternary catalysts for CO electro-oxidation were studied via CO stripping experiments, and the Pt{sub 2}Ru{sub 1}Fe{sub 1}Ni{sub 1}/C and Pt{sub 2}Ru{sub 1}Fe{sub 1}W{sub 1}/C catalysts exhibited lowered on-set potential compared to that of a commercial PtRu/C catalyst. MOR activities of the quaternary catalysts were determined by linear sweep voltammetry (LSV) experiments, and the Pt{sub 2}Ru{sub 1}Fe{sub 1}W{sub 1}/C catalyst outperformed the commercial PtRu/C catalyst by 170 and 150% for the mass and specific activities, respectively. X-ray photoelectron spectroscopy (XPS) was employed to analyze surface oxidation states of constituent atoms, and it was identified that the structure of the synthesized catalysts are close to a nano-composite of Pt and constituent metal hydroxides and oxides. In addition, the XPS results suggested that the bi-functional mechanism accounts for the improved performance of the Pt{sub 2}Ru{sub 1}Fe{sub 1}Ni{sub 1}/C and Pt{sub 2}Ru{sub 1} Fe{sub 1}W{sub 1}/C catalysts.
Energy Technology Data Exchange (ETDEWEB)
Graca Guilherme, Eneida da; Paschoal, Jose O.A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)
1992-12-31
In this work the manufacturing of Nd{sub 15}, Fe{sub 77}, B{sub 8} alloy powder for high-performance permanent magnets by reduction-diffusion process was investigated. The effect of variables such as the excess amount of neodymium oxide, the removal of calcium oxide by selective leaching and milling of alloy was examined. (author). 8 refs., 8 figs., 5 tab.s.
Efeitos corrosivos encontrados em materiais magnéticos empregados em ortodontia
Itabaiana Sobrinho, Sisenando
2006-01-01
O emprego de ligas magnéticas permitiu a criação de novas opções em terapias odontológicas, especialmente na Ortodontia, onde a sua utilização já é bastante difundida. A inovação no emprego dos magnetos veio com a introdução de novas ligas magnéticas à base dos elementos terras raras pertencentes à família dos lantanídeos, como as ligas de samário-cobalto (SmCo5) e neodímio-ferro-boro (Nd2Fe14B). Magnetos fabricados com as ligas acima são 20 vezes mais fortes que os magnetos de alumínio-níque...
Probiotyki i prebiotyki w profilaktyce i leczeniu chorób u dzieci
Directory of Open Access Journals (Sweden)
Leokadia Bąk-Romaniszyn
2010-11-01
Full Text Available Probiotyki to mikroorganizmy, które wywierają korzystne działanie na organizm gospodarza po spożyciu przez niego odpowiedniej dawki określonego szczepu. Najczęściej jako probiotyki stosowane są bakterie kwasu mlekowego Lactobacillus i Bifidobacterium oraz wybrane szczepy Streptococcus, Bacillus, a także drożdże Saccharomyces boulardii. Probiotyki wpływają korzystnie na skład środowiska ekologicznego przewodu pokarmowego, wykazując antagonizm w stosunku do drobnoustrojów chorobotwórczych kolonizujących błonę śluzową przewodu pokarmowego. Obecność w jelicie bakterii fermentacyjnych, głównie pałeczek kwasu mlekowego, a zwłaszcza typów adhezyjnych, chroni przed dyslokacją bakteryjną i enterotoksemią, normalizuje zaburzenia motoryki jelit i zmniejsza objawy nietolerancji laktozy. Prebiotyki to substancje naturalnie zawarte w żywności (bądź do niej dodawane, które selektywnie pobudzają wzrost i/lub aktywność wybranych szczepów bakterii probiotycznych obecnych w przewodzie pokarmowym. Probiotyki i prebiotyki, jak również ich połączenie – synbiotyki, występują w pożywieniu, mieszankach mlecznych, preparatach farmakologicznych, dodatkach do żywności, suplementach dietetycznych i w sposób naturalny poprawiają stan naszego zdrowia oraz mają coraz większe znaczenie w nowoczesnej medycynie. W pracy omówiono udział probiotyków i prebiotyków w kształtowaniu się biocenozy przewodu pokarmowego oraz w profilaktyce i leczeniu wybranych chorób u dzieci, jak: biegunki bakteryjne i wirusowe, dysbioza poantybiotykowa, martwica jelit noworodków, kolka jelitowa, nieswoiste zapalenia jelit, zaburzenia czynnościowe przewodu pokarmowego.
Extrinsic Curie temperature and spin reorientation changes in Nd2Fe14B/α-Fe nanocomposites
International Nuclear Information System (INIS)
Lewis, L.H.; Panchanathan, V.
1998-05-01
The Curie temperatures and spin reorientation temperatures of a series of four melt-spun nanocomposite materials comprised of Nd 2 Fe 1 4B and varying amounts of α-Fe were measured using independent techniques. The phase constitution and grain size was assessed with synchrotron x-ray diffraction; the Curie temperatures were measured by differential thermal analysis (DTA) and dc SQUID magnetometry in the temperature range 375 K ≤ T ≤ 800 K, whereas the spin reorientation transition temperature was determined from ac susceptibility measurements taken in the range 10 K ≤ T ≤ 300 K. The Curie temperature increases with increasing excess iron content, resulting in a 18 degree enhancement over the Curie temperature of pure Nd 2 Fe 14 B for 27 wt% excess α-Fe. The spin reorientation temperatures are depressed from the single-crystal value by an average of 10 degrees. Both anomalous effects are attributed to intergranular exchange coupling present in the alloys, although the effects of uncompensated stress between the constituent phases cannot be ruled out The experimental results suggest that while the Curie temperature of the Nd 2 Fe 14 B phase may be extrinsically enhanced significantly beyond the bulk value, possibly extending the range of applications of this compound, the anisotropy may be simultaneously lowered, impeding the attainment of high coercivities in these alloys
Metal Injection Molding (MIM) of NdFeB Magnets
Hartwig T.; Lopes L.; Wendhausen P.; Ünal N.
2014-01-01
Due to the increased and unstable prices for Rare Earth elements there are activities to develop alternative hard magnetic materials. Reducing the amount of material necessary to produce complex sintered NdFeB magnets can also help to reduce some of the supply problem. Metal Injection Molding (MIM) is able to produce near net shape parts and can reduce the amount of finishing to achieve final geometry. Although MIM of NdFeB has been patented and published fairly soon after the development of ...
Magnetization Reversal Mechanism for CoFeB Ferromagnetic Nanotube Arrays
International Nuclear Information System (INIS)
Hai-Rui, Liu; Qing-Feng, Lu; Shamaila, S.; Jun-Yang, Chen; Sharif, R.; Xiu-Feng, Han
2009-01-01
CoFeB nanotube arrays are fabricated in anodic aluminum oxide (AAO) membranes and track etched polycarbonate (PCTE) membranes by using an electrochemical method, and their magnetic properties are investigated by vibrating sample magnetometry. The coercivity H c and remanent squareness S Q of these CoFeB nanotube arrays are derived from hysteresis loops as a function of angle between the field and tube axis. The H c (θ) curves for CoFeB nanotube arrays in AAO and PCTE membranes show M-type variation, while they change shape from M to mountain-type as the tube length increases. However, the overall easy axis perpendicular to tube axis does not change with tube length. The different angular dependences are attributed to different magnetization reversal mechanisms. (condensed matter: electronicstructure, electrical, magnetic, and opticalproperties)
Effect of cerium on the corrosion behaviour of sintered (Nd,Ce)FeB magnet
Energy Technology Data Exchange (ETDEWEB)
Yang, Lijing [CAS Key Laboratory of Magnetic Materials and Devices, Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Bi, Mengxue [CAS Key Laboratory of Magnetic Materials and Devices, Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Nano Science and Technology Institute, University of Science and Technology of China, Hefei 230026 (China); Jiang, Jianjun; Ding, Xuefeng [CAS Key Laboratory of Magnetic Materials and Devices, Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Zhu, Minggang; Li, Wei [Functional Materials Research Institute, Central Iron & Steel Research Institute, Beijing 100081 (China); Lv, Zhongshan [Ningbo Shuo Teng new material Co., Ltd., Cixi 315301 (China); Song, Zhenlun, E-mail: songzhenlun@nimte.ac.cn [CAS Key Laboratory of Magnetic Materials and Devices, Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)
2017-06-15
Highlights: • A little Ce could promote the magnets for a better corrosion resistance. • With increased Ce contents, the corrosion resistances of magnets decrease. • As the corrosion developed, the magnetic properties decreased. - Abstract: For the balanced consumption of rare-earth elements, cerium (Ce) was partially used for NdFeB magnets instead of Nd. The corrosion behaviour of the (Nd,Ce)FeB magnet with different Ce contents in 3.5% NaCl solution was investigated by SEM, XRD, EDS and electrochemical tests. After immersion, the weight loss was calculated and the magnetic properties of the samples were measured. Results showed that Ce affected the corrosion of the (Nd,Ce)FeB magnet. Compared with the NdFeB magnet without Ce but of the same grade as the magnetic energy product, (Nd,Ce)FeB magnet showed better corrosion resistance. With increased Ce content, the corrosion resistances and magnetic properties of (Nd,Ce)FeB magnets were investigated.
Amorphous Fe-B alloys in B-Fe-Ag multilayers studied by magnetization and Mössbauer measurements
DEFF Research Database (Denmark)
Kiss, L. F.; Balogh, J.; Bujdoso, L.
2011-01-01
Bulk and local magnetic properties were studied in [1 nm B + 1 nm 57Fe + x nm Ag]5, x = 1, 2, 4, 5 and 10, multilayer samples. Although Ag does not mix with either of the other two elements the magnetic properties of the multilayers are strongly influenced by the Ag thickness below x = 5, whereas...
Fe3Nb3N precipitates of the Fe3W3C type in Nb stabilized ferritic stainless steel
International Nuclear Information System (INIS)
Malfliet, A.; Van den Broek, W.; Chassagne, F.; Mithieux, J.-D.; Blanpain, B.; Wollants, P.
2011-01-01
Highlights: → The precipitation in Nb stabilized ferritic stainless steel at 950 deg. C is investigated. → We characterized the Fe 3 Nb 3 X precipitates with SAED, EELS, WDS and AES. → We found that Fe 3 Nb 3 X precipitates are stabilized by N and not by C or O. → This insight is new and important for future development of this type of steel grade. - Abstract: A Nb stabilized ferritic stainless steel with 0.45 wt.%Nb, 82 ppm C and 170 ppm N is investigated to reveal the nature of the precipitates present at 950 deg. C. In particular, Fe 3 Nb 3 X precipitates of the Fe 3 W 3 C type are analyzed with WDS and EELS to determine the light elements X stabilizing this phase in the steel. According to WDS on large precipitates after 500 h at 950 deg. C, the Fe 3 Nb 3 X phase contains 10.4 at.% N, 1.2 at.% O and 1.0 at.% C. Auger Electron Spectroscopy on the same precipitates confirms the presence of N. In addition, it is revealed that the C and O peaks observed with WDS result from surface contamination as they disappear after Ar sputtering. The presence of a N peak in the EELS spectra of small Fe 3 Nb 3 X precipitates which have formed after 6 min at 950 deg. C indicate that N stabilizes this phase already from the initial precipitation stage. With this analysis it is demonstrated that N is an effective stabilizer of Fe 3 Nb 3 X precipitates in ferritic stainless steels. The formation of this phase should therefore be considered when predicting the precipitation behavior of Nb in industrial Nb stabilized ferritic stainless steels containing residual N.
AlN/Al dual protective coatings on NdFeB by DC magnetron sputtering
Energy Technology Data Exchange (ETDEWEB)
Li Jinlong; Mao Shoudong; Sun Kefei [Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Li Xiaomin [Shanghai Institute of Ceramics Chinese Academy of Sciences, Shanghai 200050 (China); Song Zhenlun [Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)], E-mail: songzhenlun@nimte.ac.cn
2009-11-15
AlN/Al dual protective coatings were prepared on NdFeB by DC magnetron sputtering in a home-made industrial apparatus. Comparing with Al coating, AlN/Al coatings have a denser structure of an outmost AlN amorphous layer following an inner Al columnar crystal layer. The coatings and NdFeB substrate combine well, and moreover, there is occurrence of metallurgy bonding in the interface layer. Both Al and AlN/Al coatings have a good protective ability to NdFeB. Especially, the corrosion resistance of AlN/Al coated NdFeB is improved largely. AlN/Al and Al protective coatings not only do not deteriorate the magnetic properties of NdFeB, but contribute to their slight increase.
AlN/Al dual protective coatings on NdFeB by DC magnetron sputtering
International Nuclear Information System (INIS)
Li Jinlong; Mao Shoudong; Sun Kefei; Li Xiaomin; Song Zhenlun
2009-01-01
AlN/Al dual protective coatings were prepared on NdFeB by DC magnetron sputtering in a home-made industrial apparatus. Comparing with Al coating, AlN/Al coatings have a denser structure of an outmost AlN amorphous layer following an inner Al columnar crystal layer. The coatings and NdFeB substrate combine well, and moreover, there is occurrence of metallurgy bonding in the interface layer. Both Al and AlN/Al coatings have a good protective ability to NdFeB. Especially, the corrosion resistance of AlN/Al coated NdFeB is improved largely. AlN/Al and Al protective coatings not only do not deteriorate the magnetic properties of NdFeB, but contribute to their slight increase.
Mössbauer and Kerr microscopy investigation of crystallization in FeCoB ribbons
Energy Technology Data Exchange (ETDEWEB)
Reddy, V. Raghavendra, E-mail: varimalla@yahoo.com, E-mail: vrreddy@csr.res.in; Hussain, Zaineb; Babu, Hari [UGC DAE Consortium for Scientific Research, University Campus, Kandhwa Road, Indore-452001 India (India); Shrivastava, Namrata [School of Physics, DAVV, Khandwa Road, Indore – 452001 India (India); Gupta, Ajay [Amity Centre for Spintronic Materials, Amity University, Noida 201303.India (India)
2016-05-23
The present work reports the crystallization study of amorphous FeCoB ribbons using x-ray diffraction, {sup 57}Fe Mössbauer spectroscopy in transmission mode and magneto-optical Kerr (MOKE) microscopy. Annealing at 673 K is found to result in crystallization. From the Mossbauer measurements it is observed that the Fe magnetic moments are in the plane of sample for as-cast ribbon; α-FeCo, (Fe{sub 0.5}Co{sub 0.5}){sub 2}B and Fe{sub 2}B phases are formed after crystallization. MOKE microscopy revealed that wide 180° domain walls & narrow fingerprint domains are observed before crystallization and fine domains are observed after crystallization. The results are explained in terms of the presence of internal stresses and their annealing with thermal heat treatment.
Nd-Fe-B/Sm-M/Nd-M (M = Fe, Co, Ti, Cu, Zr) hybrid magnets with improved thermal stability
Grigoras, M.; Lostun, M.; Urse, M.; Borza, F.; Chiriac, H.; Lupu, N.
2018-02-01
Hybrid magnets of Nd12Fe82B6(2:14:1-phase)/Nd9.4Fe59Co25.3Ti6.3(3:29-phase) and Nd12Fe82B6/Sm11.1Co65.8Fe8.9Cu10.7Zr3.5(2:17-phase) with different weight ratio have been prepared by spark plasma sintering pressing technique from ball-milled powders obtained from melt-spun ribbons. Influence of the ratio between the two phases on the magnetic properties and thermal stability of the hybrid magnets was studied. It has been found that the ratio has a remarkable influence, especially on the thermal stability of the bulk magnets. However, the magnetic properties of such type of hybrid magnets result not only from the type and ratio of components but also from the interaction between them. It was found that in NdFeB/3:29 hybrid magnets with 15% content of 3:29-phase, the temperature coefficients of remanence (α) and of coercivity (β) are improved from -0.095 to -0.082 (%/°C) and from -0.57 to -0.47 (%/°C), respectively, as compared to the Nd2Fe14B single-phase counterpart. While for the NdFeB/2:17 hybrid magnets the content of 2:17-phase is not significantly influencing the temperature coefficient of induction (α), the temperature coefficient of °C (β) increases up to -0.41 (%/°C) for 10% content of 2:17-phase. The increase in the reversible temperature coefficients of hybrid magnets indicate a remarkable improvement of their thermal stability.
Hida, Rachid; Falub, Claudiu V.; Perraudeau, Sandrine; Morin, Christine; Favier, Sylvie; Mazel, Yann; Saghi, Zineb; Michel, Jean-Philippe
2018-05-01
Thin films based on layers of Fe52Co28B20 (at%), Fe65Co35 (at%), and Ni80Fe20 (at%) were deposited by sputtering on 8″ bare Si and Si/200 nm-thermal-SiO2 wafers by simultaneous use of two or more cathodes. Due to the continuous rotation of the substrate cage, such that the substrates faced different targets alternately, the multilayers consisted of stacks of alternating, nanometer-thick regular layers. The composition of the films was determined by Rutherford Backscattering Spectrometry (RBS) and Nuclear Reactive Analysis (NRA), whereas Plasma Profiling Time of Flight Mass Spectrometry (PP-TOFMS) analysis gave depth profile information about the chemical elements. The structural and magnetic properties of the films were investigated by X-ray Diffraction and by TEM analysis, B-H loop tracer and high frequency single coil technique permeametry, respectively. The linear dependence of the coercivity of these thin films versus the grain size can be explained by the random anisotropy model. These novel, composite soft magnetic multilayers, with tunable in-plane anisotropy, allow operation at tunable frequencies, as shown by broadband (between 100 MHz and 10 GHz) RF measurements that exhibit a classical Landau-Lifschitz-Gilbert (LLG) behavior and, combine the magnetic properties of the individual materials in an advantageous way. This article presents a method to produce nanostructured soft magnetic multilayers, the properties of which can easily be tuned by choosing the ratio of the individual nanolayers. In this way it's possible to combine soft magnetic materials with complementary properties, e.g. high saturation magnetization, low coercivity, high specific resistivity and low magnetostriction
Effect of {gamma}-ray irradiation on the magnetic properties of NdFeB and Fe-Cr-Co permanent magnets
Energy Technology Data Exchange (ETDEWEB)
Gao, R.S. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Zhen, L. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)]. E-mail: zhenl@hit.edu.cn; Li, G.A. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Xu, C.Y. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Shao, W.Z. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)
2006-07-15
The effect of {gamma}-ray irradiation on the magnetic properties of NdFeB and Fe-Cr-Co permanent magnets has been investigated. The magnetic flux loss of two kinds of magnets before and after irradiation was measured. Results show that the effect of {gamma}-ray irradiation on the magnetic properties of sintered NdFeB is not so obvious as that on Fe-Cr-Co magnet. Irradiation-induced damage from {gamma}-ray for the Fe-Cr-Co magnets was characterized for the first time. The decline of permanent magnetic properties of Fe-Cr-Co magnet induced by {gamma}-ray irradiation is reversible except for the maximum energy product (BH){sub max}. The difference of coercivity mechanism between these two kinds of permanent magnets is responsible for the different dependence of magnetic properties loss induced by {gamma}-ray irradiation.
Evaluations of the 58Fe(n,γ)59Fe, and 54Fe(n,p)54Mn reactions for the ENDF/B-V dosimetry file
International Nuclear Information System (INIS)
Schenter, R.E.; Schmittroth, F.; Mann, F.M.
1979-10-01
A generalized least-squares adjustment procedure was used to evaluate two important dosimetry reactions for the ENDF/B-V files. Calculations for the cross section adjustments were made with the computer code FERRET, where input data included both integral and differential experimental data results. For the 54 Fe reaction, important ratio measurements were renormalized to ENDF/B-V evaluations of 235 U(n,f), 238 U(n,f), and 56 Fe(n,p). A priori curves which are required for the calculations were obtained using Hauser-Feshbach calculations from the codes NCAP ( 58 Fe) and HAUSER-5 ( 54 Fe). Covariance matrices were also calculated and are included in the evaluations. 8 figures, 1 table
Thermal stability of carbon-encapsulated Fe-Nd-B nanoparticles
International Nuclear Information System (INIS)
Bystrzejewski, M.; Cudzilo, S.; Huczko, A.; Lange, H.
2006-01-01
Thermal stability of various magnetic nanomaterials is very essential, due to their prospective future applications. In this paper, thermal behaviour of the carbon-encapsulated Fe-Nd-B nanoparticles is studied. These nanostructures were produced by direct current arcing of carbon anodes filled with Nd 2 Fe 14 B material. The thermogravimetry and differential thermal analysis curves were recorded in an oxygen atmosphere. The thermal processes were monitored by X-ray diffraction to follow the changes in the phase composition. The investigated samples have been thermally stable up to 600 K
Enrichment of W2B5 from WO3 and B2O3 by Double SHS Method
Directory of Open Access Journals (Sweden)
Bora DERIN
2018-02-01
Full Text Available A second self-propagating high-temperature synthesis (SHS was carried out to enrich the W2B5 content in the SHS product containing a mixture of various tungsten boride compounds. In the experiment, the process called Double-SHS (D-SHS was conducted in two steps. In the first SHS reaction, an initial molar composition ratio of WO3:B2O3:Mg mixture was selected as 1:3:8. The product was then hot-leached with hydrochloric acid to eliminate MgO and Mg3B2O6 phases. The leached product, consisting of 72.6 wt.% W2B5, 16.1 wt.% WB, 8.4 wt.% W2B, and 2.9 wt.% W, was again reacted with the Mg and B2O3 mixture by second SHS. After another acid leaching step, W2B5 content in the D-SHS product was found to be 98.2 wt.%. The study showed that D-SHS is an effective method for boron enrichment in the tungsten compounds.DOI: http://dx.doi.org/10.5755/j01.ms.24.1.17834
Directory of Open Access Journals (Sweden)
Analía Percíncula
2012-01-01
Full Text Available La última dictadura militar arrasó con los procesos organizativos de todo el país, a la vez que introdujo las bases del modelo de acumulación neoliberal. En el nordeste argentino esto implicó, entre otras cosas, la represión y desarticulación de las Ligas Agrarias Chaqueñas y de las Ligas Agrarias Correntinas, organizaciones que en ambos casos representaron las reivindicaciones de los sectores rurales subalternos. Paralelamente, se produjo el desmantelamiento de las producciones de algodón en el Chaco y de tabaco criollo en Corrientes, las cuales estaban en manos de productores directos, quienes se habían organizado en sus respectivas Ligas Agrarias.En este trabajo proponemos un acercamiento, en clave comparativa, a las transformaciones de la estructura agropecuaria que caracterizó a ambas provincias hasta la década del 70 y los actores colectivos conformados a partir de dicha red de relaciones socioeconómicas y políticas, es decir, las Ligas Agrarias Chaqueñas y Correntinas.
Soft magnetism, magnetostriction, and microwave properties of FeGaB thin films
International Nuclear Information System (INIS)
Lou, J.; Insignares, R. E.; Cai, Z.; Ziemer, K. S.; Liu, M.; Sun, N. X.
2007-01-01
A series of (Fe 100-y Ga y ) 1-x B x (x=0-21 and y=9-17) films were deposited; their microstructure, soft magnetism, magnetostrictive behavior, and microwave properties were investigated. The addition of B changes the FeGaB films from polycrystalline to amorphous phase and leads to excellent magnetic softness with coercivity s , self-biased ferromagnetic resonance (FMR) frequency of 1.85 GHz, narrow FMR linewidth (X band) of 16-20 Oe, and a high saturation magnetostriction constant of 70 ppm. The combination of these properties makes the FeGaB films potential candidates for tunable magnetoelectric microwave devices and other rf/microwave magnetic device applications
Magnetic and microstructural properties of thin NdFeB based films and nanostructures
Energy Technology Data Exchange (ETDEWEB)
Bommer, Lars; Goll, Dagmar [Max-Planck-Institut fuer Metallforschung, Stuttgart (Germany)
2010-07-01
The magnetic and microstructural properties of NdFeB and NdFeB/Fe thin films and nanostructures are presented. Samples with Cr buffer and protection layer (minimum thickness: d=50 nm) have been produced by ion beam sputtering at elevated temperatures (T{sub s}=700 C) using Al{sub 2}O{sub 3} and MgO(001) single crystal substrates. Films deposited on Al{sub 2}O{sub 3} substrates show c-axis growth in out-of-plane direction down to thicknesses of the NdFeB film of d=10 nm with coercivities up to {mu}{sub 0}H{sub c}=1 T. The texture of films deposited on MgO(001) substrates is less pronounced and films below d=20 nm show no hard magnetic behavior. For comparison, films were deposited at room temperature on Al{sub 2}O{sub 3} and MgO(001) followed by post-annealing in Ar atmosphere (T{sub pa}=525-650 C) leading to coercivities as high as {mu}{sub 0}H{sub c}=1.2 T but with isotropic behavior. By TEM images the grain structure of the NdFeB samples is studied. Bilayers of NdFeB (d=50 nm) and Fe (d=0-20 nm) show fully exchange coupled behavior. From the temperature dependence of the coercivity the microstructural parameters of all samples have been determined. Furthermore NdFeB periodical patterns were produced by means of electron beam lithography with dot sizes of 1000 nm and 500 nm, respectively.
Solid-solution stability and preferential site-occupancy in (R-R')2Fe14B compounds
Colin, C. V.; Ito, M.; Yano, M.; Dempsey, N. M.; Suard, E.; Givord, D.
2016-06-01
The rare-earth (R) uniaxial anisotropy of R2Fe14B compounds with magnetic R atoms (e.g., Nd or Pr) is at the origin of the exceptional hard magnetic properties achieved in magnets based on these compounds. The uniaxial anisotropy found in Ce2Fe14B is attributed mainly to the magnetism of Fe. Ce is the most abundant R element and there has been much recent effort to fabricate magnets in which Ce is partially substituted for Nd. In the present neutron study of (R1-xCex)2Fe14B (R = La or Nd), Ce is found to enter the R2Fe14B phase over the entire composition range. The crystallographic parameters decrease with increasing Ce content and the Ce atoms preferentially occupy the smaller 4f sites. It is concluded that Ce in these (RR')2Fe14B compounds essentially maintains the intermediate valence character found in Ce2Fe14B. It is proposed that, in this intermediate valence state, Ce weakly contributes to uniaxial anisotropy, thus making a link with the fact that significant coercivity is preserved in Ce-substituted NdFeB magnets.
Solid-solution stability and preferential site-occupancy in (R-R′)2Fe14B compounds
International Nuclear Information System (INIS)
Colin, C. V.; Dempsey, N. M.; Ito, M.; Yano, M.; Suard, E.; Givord, D.
2016-01-01
The rare-earth (R) uniaxial anisotropy of R 2 Fe 14 B compounds with magnetic R atoms (e.g., Nd or Pr) is at the origin of the exceptional hard magnetic properties achieved in magnets based on these compounds. The uniaxial anisotropy found in Ce 2 Fe 14 B is attributed mainly to the magnetism of Fe. Ce is the most abundant R element and there has been much recent effort to fabricate magnets in which Ce is partially substituted for Nd. In the present neutron study of (R 1−x Ce x ) 2 Fe 14 B (R = La or Nd), Ce is found to enter the R 2 Fe 14 B phase over the entire composition range. The crystallographic parameters decrease with increasing Ce content and the Ce atoms preferentially occupy the smaller 4f sites. It is concluded that Ce in these (RR′) 2 Fe 14 B compounds essentially maintains the intermediate valence character found in Ce 2 Fe 14 B. It is proposed that, in this intermediate valence state, Ce weakly contributes to uniaxial anisotropy, thus making a link with the fact that significant coercivity is preserved in Ce-substituted NdFeB magnets.
International Nuclear Information System (INIS)
Karen, P.
2003-01-01
Evolutions of the mixed-valence (MV) and charge-ordered (CO) phases of GdBaFe 2 O 5+w-bar are investigated as a function of w-bar(-0.02 V indicate that the coexistence is largely owing to X(w), resulting in different parts of the sample having slightly different T V . Below w-bar=0.04, a premonitory charge-ordering transition is registered by DSC, having no detectable structural effect. Below w-bar∼0.02, a 3D long-range order of charges of the TbBaFe 2 O 5 -type appears. For a w-bar=-0.001 composition, 21 weak superstructure Bragg reflections is visually identified. Intensity resolution for several of them depends heavily on fine modeling of the main-peak footings affected by two types of oxygen disorder: X(w) and a residual tetragonal disorder. Both are successfully simulated by a multiple-phase Rietveld refinement. Thermodynamic parameters of the two transitions at the ideal composition with w-bar=0 are evaluated from composition dependences
Tang, Jin; Liu, Xiansong; Mehmood Ur Rehman, Khalid; Li, Dan; Li, Mingling; Yang, Yujie
2018-04-01
We report a successful preparation of Ba1-xLaxFe22+Fe163+O27 (x = 0.00-0.10) W-type hexagonal ferrites by standard ceramic method in a reduced oxygen atmosphere. In this work, the effect of the substitution La3+ rare-earth ions for Ba2+ ions on the structural and magnetic properties of the prepared samples have been studied. The phase identification of magnetic powders was performed by X-ray diffraction. The results of XRD show that the single phase was observed in the W-type ferrites with different La content. The SEM micrographs showed that the ferrites have formed the hexagonal structure. The magnetic properties of the samples were metric by a vibrating sample magnetometer. The coercivity (Hc) of the particles decreases with the increase of La content(x), while the saturation magnetization (Ms) of the particles first increases with x from 0 to 0.05, and then begins to decrease when x continues to increase. The monotonic dependence of the magnetic anisotropy field Ha and coercivity Hc on the La3+ doping amount is found to be mainly dominated by the competition between Ms and Keff.
Investigation Procedure of Magnetic Performances of NdFeB Permanent Magnets
DEFF Research Database (Denmark)
Calin, Marius-Daniel; Helerea, Elena; Ritchie, Ewen
2011-01-01
The permanent magnet applications based on carbon steel magnets, hard ferrites and AlNiCo magnets classes are renewed with new classes of advanced magnetic materials based on rare earth elements, the Sm-Co and NdFeB types. Performance increase of the hard magnetic materials and their use in speci......The permanent magnet applications based on carbon steel magnets, hard ferrites and AlNiCo magnets classes are renewed with new classes of advanced magnetic materials based on rare earth elements, the Sm-Co and NdFeB types. Performance increase of the hard magnetic materials and their use...... in specific applications impose also great advances in the field of magnetic measurement. New researches need to be validated in order to investigate the NdFeB permanent magnets performances, including their stability under different thermal operational regimes. In this paper a specific investigation...... procedure of magnetic performances of NdFeB permanent magnets in correlation with the range of operating temperature is proposed based on modern hysteresisgraph method and impulse magnetization technique....
Impulse Magnetization of Nd-Fe-B Sintered Magnets for Sensors
Directory of Open Access Journals (Sweden)
Marek Przybylski
2016-04-01
Full Text Available Magnetization of large Nd-Fe-B sintered permanent magnets is still challenging. This type of permanent magnet is electrically conductive, so impulse magnetization causes a flow of eddy currents which prevent magnetization of the whole volume of the magnet. The paper deals with the impulse magnetization of sintered Nd-Fe-B permanent magnets and shows a method for the determination of suitable parameters for the supply system. The necessary magnetic field strength for magnetization of the magnet to saturation was determined. The optimal magnetizing fixture supply voltage for magnetization to saturation was determined from simulations in PSpice software, finite element analyses in Maxwell 15 and measurements. Measurements of magnetic induction on the surface of the Nd-Fe-B magnet are also presented to ensure that a magnet with 70 mm diameter and 20 mm in height is fully saturated.
Production of NdFeB powders by HDDR from sintered magnets
International Nuclear Information System (INIS)
Janasi, S.R.; Rodrigues, D.; Landgraf, F.J.G.; Campos, M.F. de
2010-01-01
The production of NdFeB powders by the HDDR process from metallic alloys has been widely investigated. Different HD and DR conditions have been used to induce anisotropy and to improve the intrinsic coercivity of the obtained powders. The purpose of this study is to apply the HDDR process in the reprocessing of NdFeB sintered magnet scraps. There were investigated different processing conditions as temperature and time of desorption and recombination (DR). The results of X ray diffraction show the formation of the magnetic phase Nd 2 Fe 14 B in all the investigated conditions. Magnetic measurements by vibrating sample magnetometer indicate that powders with intrinsic coercivity up to 790 kA/m were obtained. (author)
Directory of Open Access Journals (Sweden)
Grzegorz Józef Nowicki
2017-03-01
Full Text Available Cel pracy. Określenie stanu wiedzy na temat czynników ryzyka i profilaktyki wybranych chorób cywilizacyjnych i określenie związku z poziomem deklarowanych zachowań zdrowotnych wśród pracowników medycznych i niemedycznych. Materiał i metody. Badania przeprowadzono wśród 598 dorosłych osób pracujących, wykonujących zawody medyczne (grupa M i pozamedyczne (grupa P. Metodą badawczą był sondaż diagnostyczny przy użyciu Testu wiedzy na temat czynników ryzyka i profilaktyki chorób cywilizacyjnych (własnego autorstwa oraz Inwentarza Zachowań Zdrowotnych (IZZ. Wyniki. Analizując materiał badawczy na temat stanu wiedzy o czynnikach ryzyka i profilaktyce chorób cywilizacyjnych uzyskany od osób z grupy M, stwierdzono że: niski poziom wiedzy charakteryzował 1,97% (n=6 badanych, przeciętny 29,18% (n=89 a wysoki aż 68,85% (n=210. Natomiast w grupa P niski poziomem wiedzy charakteryzował 16,04% (n=47 respondentów, 55,29% (n=162 przeciętny, a 28,67% (n=84 – wysoki. Stwierdzono, że wśród badanych z grupy P wraz ze wzrostem poziomu wiedzy na temat czynników ryzyka i profilaktyki chorób cywilizacyjnych rośnie ocena ogólnego wskaźnika zachowań zdrowotnych oraz jego czterech kategorii (p<0,05. Wnioski. Stan wiedzy na temat czynników ryzyka i profilaktyki chorób cywilizacyjnych stanowi ważny czynnik determinujący poziom zachowań zdrowotnych głównie wśród osób wykonujących zawody pozamedyczne.
On the angular dependence of the coercivity of NdFeB hard magnets
International Nuclear Information System (INIS)
Jahn, L.; Christoph, V.; Pastuschenko, J.S.
1989-01-01
In order to test the model assumptions on hard magnetic properties of sintered NdFeB magnets, a comparison of the measured and calculated values of the magnetization and remanence coercivities H C and H R , respectively, as a function of the angle between texture axis and external field θ in Nd 16 Fe 76 B 8 and (Nd 0.9 Tb 0.1 ) 16 Fe 76 B 8 is given and explained qualitatively
Directory of Open Access Journals (Sweden)
Jorge León
2011-06-01
Full Text Available Objetivos. Determinar el potencial antimicrobiano de actinomicetos marinos frente a cepas S. aureus meticilino-resistentes (MRSA y E. faecalis vancomicina-resistentes (VRE. Materiales y métodos. En dos medios de cultivo se sembraron 29 cepas de actinomicetos aislados de sedimento marino. Se evaluó la capacidad inhibitoria mediante pruebas de antagonismo in vitro para MRSA y VRE. Se procesó los extractos orgánicos de tres actinomicetos seleccionados para determinar la Concentración Mínima Inhibitoria (CMI del compuesto activo. Resultados. La mayoría de los actinomicetos aislados correspondieron a un grupo homogéneo de blanco-grisáceos (62% con buen nivel de crecimiento en agar marino. Los porcentajes inhibitorios fueron superiores a 85% para ambos patógenos con halos de inhibición mayores a 69 y 78 mm de diámetro para MRSA y VRE respectivamente. Los extractos diclorometánicos de tres de los actinomicetos aislados (I-400A, B1-T61, M10-77 mostraron gran potencial inhibitorio de ambos patógenos, siendo M10-77 la cepa de actinomiceto de mayor actividad antibiótica frente a S. aureus ATCC 43300 resistente a meticilina y E. faecalis ATCC 51299 resistente a vancomicina con una Concentración Mínima Inhibitoria (CMI de 7,9 y 31,7 μg/ mL respectivamente. El análisis filogenético de la cepa M10- 77 presenta un 99% de similaridad con la especie marina Streptomyces erythrogriseus. Conclusiones. El sedimento marino de la costa central del Perú es fuente promisorio de cepas de actinomicetos con gran capacidad de producir compuestos bioactivos capaces de inhibir patógenos tipificados como multidrogo-resistentes tales como S. aureus meticilino resistentes y E. faecalis vancomicina resistentes.Objectives. To determine the antimicrobial potential of marine actinomycetes against drug-resistant pathogens represented by strains of methicillin-resistant Staphylococcus aureus (MRSA and vancomycin-resistant Enterococcus faecalis (VRE. Materials and
Metal Injection Molding (MIM of NdFeB Magnets
Directory of Open Access Journals (Sweden)
Hartwig T.
2014-07-01
Full Text Available Due to the increased and unstable prices for Rare Earth elements there are activities to develop alternative hard magnetic materials. Reducing the amount of material necessary to produce complex sintered NdFeB magnets can also help to reduce some of the supply problem. Metal Injection Molding (MIM is able to produce near net shape parts and can reduce the amount of finishing to achieve final geometry. Although MIM of NdFeB has been patented and published fairly soon after the development of the NdFeB magnets there has never been an industrial production. This could be due to the fact that MIM was very young at that time and hardly developed. Thus, the feasibility of the process needs to be revaluated. This paper presents results of our work on determining the process parameters influencing the magnetic properties of the sintered magnets as well as the shrinkage during processing. The role of binder and powder loading on the alignment of the particles as well as on the carbon and oxygen contamination was examined.
Effect of γ-(Fe,Ni) crystal-size stabilization in Fe-Ni-B amorphous ribbon
Gorshenkov, M. V.; Glezer, A. M.; Korchuganova, O. A.; Aleev, A. A.; Shurygina, N. A.
2017-02-01
The effect of stabilizing crystal size in a melt-quenched amorphous Fe50Ni33B17 ribbon is described upon crystallization in a temperature range of 360-400°C. The shape, size, volume fraction, and volume density have been investigated by transmission electron microscopy and X-ray diffraction methods. The formation of an amorphous layer of the Fe50Ni29B21 compound was found by means of atomic-probe tomography at the boundary of the crystallite-amorphous phase. The stabilization of crystal sizes during annealing is due to the formation of a barrier amorphous layer that has a crystallization temperature that exceeds the crystallization temperature of the matrix amorphous alloy.
2010-07-26
... DEPARTMENT OF LABOR Employment and Training Administration TA-W-73,381, MT Rail Link, Inc., Missoula, MT; TA-W-73,381A, Billings, MT; TA-W-73,381B, Laurel, MT; TA-W-73,381C, Livingston, MT; TA-W-73... Helena, Montana. The amended notice applicable to TA-W-73,381 is hereby issued as follows: All workers of...
Roles of Co element in Fe-based bulk metallic glasses utilizing industrial FeB alloy as raw material
Directory of Open Access Journals (Sweden)
Shouyuan Wang
2017-08-01
Full Text Available A series of Fe-based bulk metallic glasses were fabricated by a conventional copper mold casting method using a kind of Fe-B industrial raw alloy. It is found that Fe-B-Y-Nb bulk metallic glass with 3 at% of Co addition possesses the best glass forming ability, thermal stability, hardness, magnetic property and anti-corrosion property. The hardness test result indicates a synchronically trend with glass-forming ability parameters. The excellent glass-forming ability and a combination of good mechanical and functional properties suggest that the alloys in this work might be good candidates for commercial use.
FeNbB bulk metallic glass with high boron content
Energy Technology Data Exchange (ETDEWEB)
Stoica, M.; Das, Jayanta; Eckert, Juergen [IFW Dresden, Institute for Complex Materials, P.O. Box 270016, D-01171 Dresden (Germany); Hajlaoui, Khalil; Yavari, Alain Reza [LTPCM-CNRS, I.N.P. Grenoble, 1130 Rue de la Piscine, BP 75, F-38402 University Campus (France)
2007-07-01
Fe-based alloys able to form magnetic bulk metallic glasses (BMGs) are of the type transition metal - metalloid and often contain 5 or more elements. Usually, the metalloid content is around 20 atomic %. Very recently, the Fe{sub 66}Nb{sub 4}B{sub 30} alloy was found to be able to form BMG by copper mold casting technique, despite its high metalloid content. Several composition with boron contents around 30 at. % or even higher were calculated since 1993 as possible compositions of the remaining amorphous matrix after the first stage of nanocrystallization of Finemet-type Fe{sub 77}Si{sub 14}B{sub 9} glassy ribbons with 0.5 to 1 atomic % Cu and a few percent Nb addition. Melt-spun ribbons of all calculated compositions were found to be glassy. The composition of the ternary Fe-based BMG investigated in the present study resulted as an optimization of all possibilities. The alloy is ferromagnetic with glass transition temperature T{sub g}=845 K, crystallisation temperature T{sub x}=876 K, liquidus temperature T{sub liq}=1451 K and mechanical strength of 4 GPa. The coercivity of as-cast samples is very low, around 1.5 A/m. The present contribution aims at discussing the thermal stability, mechanical and magnetic properties of the Fe{sub 66}Nb{sub 4}B{sub 30} BMG.
Park, Shin Ae; Lee, Hee Jung; Cho, Yea Jin; Choi, Sora; Oh, Moonhyun
2014-05-05
A precise fabrication of nanobamboo structures made from hybrid coordination polymers of the type {Fex In1-x }-MIL-88B is demonstrated. The compositions of the hybrid coordination polymer nanobamboos of {Fex In1-x }-MIL-88B (x=0.06, 0.19, or 0.75) are regulated by altering the amount of metal ions used in the reactions. Interestingly, the formation of a virtual In-MIL-88B (precise structure, {Fe0.06 In0.94 }-MIL-88B), which cannot be created in a typical reaction, is induced by the assistance of a Fe-MIL-88B structure. The a and c cell parameters of {Fe0.06 In0.94 }-MIL-88B are calculated at 10.95 and 19.86 Å, respectively. These values of {Fe0.06 In0.94 }-MIL-88B are larger than those of pure Fe-MIL-88B owing to the large ionic size of In(3+) within the framework. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Net Shape 3D Printed NdFeB Permanent Magnet
Jacimovic, J.; Binda, F.; Herrmann, L. G.; Greuter, F.; Genta, J.; Calvo, M.; Tomse, T.; Simon, R. A.
2016-01-01
For two decades, NdFeB based magnets have been a critical component in a range of electrical devices engaged in energy production and conversion. The magnet shape and the internal microstructure of the selected NdFeB grade govern their efficiency and size. However, stricter requirements on device efficiency call for better performing magnets preferably with novel functionality not achievable today. Here we use 3D metal printing by Selective Laser Melting to fabricate dense net shape permanent...
Directory of Open Access Journals (Sweden)
Graciana Maria de Moraes
2013-01-01
Full Text Available OBJETIVO: Identificar os fatores preditores de infecção ou colonização por micro-organismos resistentes. MÉTODOS: Foi realizado estudo quantitativo de coorte prospectivo. Foram realizadas a análise descritiva, para conhecimento da população do estudo, e a análise discriminante, para identificação dos fatores preditores. RESULTADOS: Foram incluídos 85 pacientes com infecções por micro-organismos resistentes: Pseudomonas aeruginosas resistente aos carbapenêmicos (24,7%, Acinetobacter resistente aos carbapenêmicos (21,2%, Staphylococcus aureus resistente à meticilina (25,9%, Enterococcus spp. resistente à vancomicina (17,6% e Klebsiella pneumoniae resistente aos carbapenêmicos (10,6%. A análise discriminante identificou transferências de outros hospitais e internação na Unidade de Terapia Intensiva como fatores preditores para ocorrência de infecção pelos grupos S. aureus resistente à meticilina, Acinetobacter resistente aos carbapenêmicos e K. pneumoniae resistente aos carbapenêmicos. Nenhuma das variáveis estudadas foi discriminante para Enterococcus spp. resistente à vancomicina e P. aeruginosas resistente aos carbapenêmico. CONCLUSÃO: Os fatores preditores encontrados foram: internação na UTI e a transferências de outros hospitais.OBJECTIVE: Identifying predictors of infection or colonization with resistant microorganisms. METHODS: A quantitative study of prospective cohort was carried out. A descriptive analysis was performed in order to know the population of the study and a discriminant analysis was performed to identify the predictors. RESULTS: In this study were included 85 patients with infections caused by resistant microorganisms: carbapenem-resistant Pseudomonas aeruginosas (24.7%; carbapenem-resistant Acinetobacter (21.2%; methicillin-resistant Staphylococcus aureus (25.9%, vancomycin-resistant Enterococcus spp (17.6% and carbapenem-resistant Klebsiella pneumonia (10.6%. The discriminant analysis
Energy Technology Data Exchange (ETDEWEB)
McGuire, Michael A., E-mail: McGuireMA@ornl.gov; Parker, David S. [Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States)
2015-10-28
Crystallographic and magnetic properties of Fe{sub 5}PB{sub 2}, Fe{sub 4}CoPB{sub 2}, Fe{sub 4}MnPB{sub 2}, Fe{sub 5}SiB{sub 2}, Fe{sub 4}CoSiB{sub 2}, and Fe{sub 4}MnSiB{sub 2} are reported. All adopt the tetragonal Cr{sub 5}B{sub 3} structure-type and are ferromagnetic at room temperature with easy axis of magnetization along the c-axis. The spin reorientation in Fe{sub 5}SiB{sub 2} is observed as an anomaly in the magnetization near 170 K and is suppressed by substitution of Co or Mn for Fe. The silicides are found to generally have larger magnetic moments than the phosphides, but the data suggest smaller magnetic anisotropy in the silicides. Cobalt substitution reduces the Curie temperatures by more than 100 K and ordered magnetic moments by 16%–20%, while manganese substitution has a much smaller effect. This suggests Mn moments align ferromagnetically with the Fe and that Co does not have an ordered moment in these structures. Anisotropic thermal expansion is observed in Fe{sub 5}PB{sub 2} and Fe{sub 5}SiB{sub 2}, with negative thermal expansion seen along the c-axis of Fe{sub 5}SiB{sub 2}. First principles calculations of the magnetic properties of Fe{sub 5}SiB{sub 2} and Fe{sub 4}MnSiB{sub 2} are reported. The results, including the magnetic moment and anisotropy, are in good agreement with experiment.
Nitrided FeB amorphous thin films for magneto mechanical systems
International Nuclear Information System (INIS)
Fernandez-Martinez, I.; Martin-Gonzalez, M.S.; Gonzalez-Arrabal, R.; Alvarez-Sanchez, R.; Briones, F.; Costa-Kraemer, J.L.
2008-01-01
The structural, magnetic and magnetoelastic properties of Fe-B-N amorphous films, sputtered from a Fe 80 B 20 target, in a mixture of argon and nitrogen gas, are studied for different nitrogen partial pressures. Nitrogen incorporates into the film preserving the amorphous structure, and modifying magnetic properties. The amount of nitrogen that incorporates into the amorphous structure is found to scale linearly with the nitrogen partial pressure during film growth. The structure, magnetization, field evolution, magnetic anisotropy and magnetostrictive behaviour are determined for films with different nitrogen content. An ∼20% increase of both the saturation magnetization and the magnetostriction constant values is found for moderate (∼8%) nitrogen content when compared to those for pure Fe 80 B 20 amorphous films. These improved properties, together with the still low coercivity of the amorphous films offer great potential for their use in magnetostrictive micro and nano magneto mechanical actuator devices
Hot-working behavior of cast Pr-Fe-B magnets
International Nuclear Information System (INIS)
Shimoda, T.; Akioka, K.; Kobayashi, O.; Yamagami, T.; Ohki, T.; Miyagawa, M.; Yuri, T.
1989-01-01
The hot-working behavior of cast Pr-Fe-B magnets is investigated. The hot-working is done both at a low strain rate (hot-pressing) and a high strain rate (hot-rolling). Magnetic alignment induced by the hot-working is found to be closely related to the macrostructure of the cast ingots and the direction of principal stress. The appropriate structure is a columnar structure. The c-axis of the Pr2Fe14B phase is lying in the plane perpendicular to the growth direction of the dendrites. The principal stress during working should be given perpendicular to the growth direction
Reactive diffusion in amorphous Fe-B and Co-Zr multilayer films
International Nuclear Information System (INIS)
Stobiecki, F.
1989-01-01
The diffusion in Fe 1-x B x /Fe 1-y B y and Co 1-x Zr x /Co 1-y Zr y amorphous bi- and multilayers was investigated. The dependence of the diffusion coefficient on concentration was observed. This effect is explained taking into account the concentration dependence of mixing enthalpy correlated with chemical short range order in the amorphous state
Microstructural Influence on Dynamic Properties of Age Hardenable FeMnAl Alloys
2011-04-01
strain amplitude on a wrought Fe-28Mn-9Al-0.86C-0.7W-0.43Mo-0.49Nb alloy and on a martensitic stainless steel of composition Fe-12Cr-1.25Ni-0.2V-1.8W...the martensite and loss of strength was used to explain the lower cyclic life of the stainless steel at elevated temperatures. Within the Fe-Mn-Al-C...through F in Table 2), 1010 carbon steel and 304 stainless steel as functions of exposure time in 1 atm flowing oxygen at 700°C (a) and 500°C (b).56
Study of high-coercivity sintered NdFeB magnets
International Nuclear Information System (INIS)
Bai, G.; Gao, R.W.; Sun, Y.; Han, G.B.; Wang, B.
2007-01-01
Magnetic powders for sintered NdFeB magnets have been prepared by using an advanced processing method including strip casting, hydrogen decrepitation, jet milling and rubber isotropic press. The effects of Dy, Ga and Co addition on the microstructure and magnetic properties of sintered magnets have been investigated. By adopting a suitable component ratio and adjusting proper technological parameters, we have prepared high-coercivity sintered NdFeB magnets with hard magnetic properties of j H c =25.6 kOe, B r =13.2 kG and (BH) max =39.9 MGOe. The temperature coefficient of coercivity of the magnets (between 20 and 150 deg. C) is -0.53% deg. C. The magnetic properties at high temperature satisfy the needs of permanent magnet motors
NdFeB thick films prepared by tape casting
International Nuclear Information System (INIS)
Pawlowski, B.; Schwarzer, S.; Rahmig, A.; Toepfer, J.
2003-01-01
NdFeB films of thickness between 100 and 800 μm were prepared by tape casting of a slurry containing 84-95 wt% of commercial NdFeB powder (MQP-B, -Q and -S). After curing the flexible green tapes at 120 deg. C non-porous magnetic films are obtained. The remanence of the films is in the range of 350-450 mT and the coercivity is between 300 and 800 kA/m depending on the type of MQP powder used. The magnetic properties of the films are discussed in relation to film composition and type of magnetic material. For MEMS applications the thick films are magnetized with a multi-pole stripe pattern with 1 mm pole pitch. The induction at the surface of the films was measured with a Hall probe and compared to theoretical calculations. The results indicate that the films are completely magnetized regardless of the film thickness. Tape-casted NdFeB thick films are promising candidates for applications in micro-systems or actuators. Miniaturization of the magnet components is one of the key issues in the development of electromagnetic micro-systems, thus creating a need for replacement of small sintered magnets by magnetic thick film components. Other applications include encoders
Characterization of corrosion products from Nd-Fe-B magnets used in dental prostheses
Energy Technology Data Exchange (ETDEWEB)
Saiki, Mitiko; Rogero, Sizue O.; Costa, Isolda; Dantas, Elisabeth; Oliveira, Mara C.L. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)
2002-07-01
A special group of magnets composed mainly by Nd-Fe-B has been widely used in dental applications as retentive devices for overdentures, due to their strong force and compactness. Dental materials should present high corrosion resistance and be innocuous to human tissues, however, Nd-Fe-B magnets are highly susceptible to corrosion. This work presents results obtained in the elemental analysis of Nd-Fe-B magnets and their corrosion products. The corrosion products were analyzed in the extracts of culture medium where the magnets had been immersed for 10 days at 37 deg C. Elements B, Co, Fe, La, Nd, Dy, Pr, Sm, Ho, Yb and Lu were found in the magnet and the analysis of extract indicated that Co, Fe and Nd are released from the magnet to the extract. Toxicity was also investigated in this extract using the neutral red uptake cytotoxicity assay. Acknowledgements: To FAPESP and CNPq for financial support. (author)
Characterization of corrosion products from Nd-Fe-B magnets used in dental prostheses
International Nuclear Information System (INIS)
Saiki, Mitiko; Rogero, Sizue O.; Costa, Isolda; Dantas, Elisabeth; Oliveira, Mara C.L.
2002-01-01
A special group of magnets composed mainly by Nd-Fe-B has been widely used in dental applications as retentive devices for overdentures, due to their strong force and compactness. Dental materials should present high corrosion resistance and be innocuous to human tissues, however, Nd-Fe-B magnets are highly susceptible to corrosion. This work presents results obtained in the elemental analysis of Nd-Fe-B magnets and their corrosion products. The corrosion products were analyzed in the extracts of culture medium where the magnets had been immersed for 10 days at 37 deg C. Elements B, Co, Fe, La, Nd, Dy, Pr, Sm, Ho, Yb and Lu were found in the magnet and the analysis of extract indicated that Co, Fe and Nd are released from the magnet to the extract. Toxicity was also investigated in this extract using the neutral red uptake cytotoxicity assay. Acknowledgements: To FAPESP and CNPq for financial support. (author)
Domain structures and magnetization reversal in Co/Pd and CoFeB/Pd multilayers
Energy Technology Data Exchange (ETDEWEB)
Sbiaa, R., E-mail: rachid@squ.edu.om [Department of Physics, Sultan Qaboos University, P.O. Box 36, PC 123 (Oman); Ranjbar, M. [Physics Department, University of Gothenburg, 412 96 Gothenburg (Sweden); Åkerman, J. [Physics Department, University of Gothenburg, 412 96 Gothenburg (Sweden); Materials Physics, School of ICT, Royal Institute of Technology (KTH), 164 40 Kista (Sweden)
2015-05-07
Domain structures and magnetization reversal of (Co/Pd) and (CoFeB/Pd) multilayers with 7 and 14 repeats were investigated. The Co-based multilayers show much larger coercivities, a better squareness, and a sharper magnetization switching than CoFeB-based multilayers. From magnetic force microscopy observations, both structures show strong reduction in domains size as the number of repeats increases but the magnetic domains for Co-based multilayers are more than one order of magnitude larger than for CoFeB-based multilayers. By imaging domains at different times, breaks in the (CoFeB/Pd) multilayer stripes were observed within only few hours, while no change could be seen for (Co/Pd) multilayers. Although CoFeB single layers are suitable for magnetoresistive devices due to their large spin polarization and low damping constants, their lamination with Pd suffers mainly from thermal instability.
Enhancement of exchange coupling interaction of NdFeB/MnBi hybrid magnets
Nguyen, Truong Xuan; Nguyen, Khanh Van; Nguyen, Vuong Van
2018-03-01
MnBi ribbons were fabricated by melt - spinning with subsequent annealing. The MnBi ribbons were ground and mixed with NdFeB commercial Magnequench powders (MQA). The hybrid powder mixtures were subjected thrice to the annealing and ball-milling route. The hybrid magnets (100 - x)NdFeB/xMnBi, x=0, 30, 40, 50 and 100 wt% were in-mold aligned in an 18 kOe magnetic field and warm compacted at 290 °C by 2000 psi uniaxial pressure for 10 min. An enhancement of the exchange coupling of NdFeB/MnBi hybrid magnets was obtained by optimizing the magnets' microstructures via annealing and ball-milling processes. The magnetic properties of prepared NdFeB/MnBi hybrid magnets were studied and discussed in details.
Energy Technology Data Exchange (ETDEWEB)
Lakshmanan, Saravanan; Rao, Subha Krishna [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India); Muthuvel, Manivel Raja [Defence Metallurgical Research Laboratory (DMRL), Hyderabad 500058 (India); Chandrasekaran, Gopalakrishnan [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India); Therese, Helen Annal, E-mail: helen.a@ktr.srmuniv.ac.in [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India)
2017-08-01
Highlights: • Ta/CoFeB(50 nm)/Ta thin films were deposited at various substrate temperatures (T{sub s}). • CoFeB films deposited at T{sub s} such as RT, 450 °C, 475 °C and 500 °C exhibited perpendicular coercivity. • CoFeB deposited at 475 °C displayed a higher coercivity of 315 Oe and a low M{sub s} of 169 emu/cc. • The enhanced crystallization of CoFeB at the Ta/CoFeB interface results in higher H{sub c} (⟂). - Abstract: Magnetization of Ta/CoFeB/Ta trilayer films with thick layer of CoFeB deposited under different substrate temperatures (T{sub s}) via ultra-high vacuum DC sputtering technique has been measured with the applied magnetic field parallel and perpendicular to the plane of the film respectively to study the perpendicular coercive forces of the film. The samples were further analyzed for its structural, topological, morphological, and electrical transport properties. The core chemical states for the elements present in the CoFeB thin film were analyzed by XPS studies. Magnetization studies reveal the existence of perpendicular coercive forces in CoFeB films deposited only at certain temperatures such as RT, 450 °C, 475 °C and 500 °C. CoFeB film deposited at 475 °C exhibited a maximum coercivity of 315 Oe and a very low saturation magnetization (M{sub s}) of 169 emu/cc in perpendicular direction. This pronounced effect in perpendicular coercive forces observed for CoFeB475 could be attributed to the effect of temperature in enhancing the crystallization of the film at the Ta/CoFeB interfaces. However at temperatures higher than 475 °C the destruction of the Ta/CoFeB interface due to intermixing of Ta and CoFeB results in the disappearance of magnetic anisotropy.
Trapped magnetic field in a (NdFeB)–(MgB2) pair-type bulk magnet
International Nuclear Information System (INIS)
Aldica, Gheorghe; Burdusel, Mihail; Badica, Petre
2014-01-01
Highlights: • Dense MgB 2 discs were obtained by ex-situ Spark Plasma Sintering. • A NdFeB–MgB 2 pair-type bulk magnet was tested for different working conditions. • The polarity of the NdFeB permanent magnet influences macro flux jumps of MgB 2 . • Trapped field of the pair was 2.45 T (20 K) and 3.3 T (12 K). - Abstract: Superconducting bulk discs, S, of 20 mm in diameter and 3.5 or 3.3 mm thickness of MgB 2 (pristine or added with cubic BN, respectively) with density above 97% were prepared by Spark Plasma Sintering. Discs were combined in a pair-type sandwich-like arrangement with a permanent NdFeB axially magnetised magnet, PM (∼0.5 T). Measurement of the trapped field, B tr , with temperature, time, and the reduction rate of the applied magnetic field was performed using a Hall sensor positioned at the centre between the superconductor and the permanent magnet. It is shown that the permanent magnet with certain polarity favors higher trapped field of the superconductor owing to suppression of flux jumps specific for high density MgB 2 samples. The B tr of the PM–S pair was 2.45 T (20 K) and 3.3 T (12 K)
Preparation and magnetic properties of anisotropic bulk MnBi/NdFeB hybrid magnets
International Nuclear Information System (INIS)
Ma, Y.L.; Liu, X.B.; Nguyen, V.V.; Poudyal, N.; Yue, M.; Liu, J.P.
2016-01-01
Anisotropic hybrid bulk magnets of MnBi/NdFeB with different composition ratio have been prepared with starting MnBi and Nd 2 Fe 14 B powders as well as epoxy resin as a binder in case it is needed to form bulk samples. It has been found that the ratio between the two phases in content has a remarkable influence on the magnetic properties, the thermal stability and the density of the bulk magnets. With increasing MnBi content the binder addition can be reduced. When the MnBi content is larger than 30 wt%, no binder is needed. On the other hand, the coercivity and saturation magnetization were increased significantly with increasing NdFeB content. When the NdFeB content was increased from 0% to 50%, the maximum energy product was enhanced from 4.7 to 10.0 MGOe, respectively. The energy product then decreased gradually with the NdFeB content due to the reduced density of the hybrid magnet. The thermal stability measurements showed that the temperature coefficient of coercivity grew with the MnBi content and became positive with MnBi=80 wt%. - Highlights: • Anisotropic bulk hybrid MnBi/NdFeB magnets were prepared. • MnBi content affected the density and coercivity temperature coefficient positively. • An energy product (BH) max of 10 MGOe was obtained at NdFeB content of 50 wt%.
Preparation and magnetic properties of anisotropic bulk MnBi/NdFeB hybrid magnets
Energy Technology Data Exchange (ETDEWEB)
Ma, Y.L. [Department of Physics, University of Texas at Arlington, Arlington, TX 76019 (United States); College of Metallurgical and Materials Engineering, Chongqing University of Science and Technology, Chongqing 401331 (China); Liu, X.B.; Nguyen, V.V.; Poudyal, N. [Department of Physics, University of Texas at Arlington, Arlington, TX 76019 (United States); Yue, M. [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Liu, J.P., E-mail: pliu@uta.edu [Department of Physics, University of Texas at Arlington, Arlington, TX 76019 (United States)
2016-08-01
Anisotropic hybrid bulk magnets of MnBi/NdFeB with different composition ratio have been prepared with starting MnBi and Nd{sub 2}Fe{sub 14}B powders as well as epoxy resin as a binder in case it is needed to form bulk samples. It has been found that the ratio between the two phases in content has a remarkable influence on the magnetic properties, the thermal stability and the density of the bulk magnets. With increasing MnBi content the binder addition can be reduced. When the MnBi content is larger than 30 wt%, no binder is needed. On the other hand, the coercivity and saturation magnetization were increased significantly with increasing NdFeB content. When the NdFeB content was increased from 0% to 50%, the maximum energy product was enhanced from 4.7 to 10.0 MGOe, respectively. The energy product then decreased gradually with the NdFeB content due to the reduced density of the hybrid magnet. The thermal stability measurements showed that the temperature coefficient of coercivity grew with the MnBi content and became positive with MnBi=80 wt%. - Highlights: • Anisotropic bulk hybrid MnBi/NdFeB magnets were prepared. • MnBi content affected the density and coercivity temperature coefficient positively. • An energy product (BH){sub max} of 10 MGOe was obtained at NdFeB content of 50 wt%.
Enter B and W: two new meningococcal vaccine programmes launched.
Ladhani, Shamez N; Ramsay, Mary; Borrow, Ray; Riordan, Andrew; Watson, John M; Pollard, Andrew J
2016-01-01
In 2015, the UK became the first country in the world to have a comprehensive routine meningococcal vaccine programme targeting all of the main capsular groups of N. meningitidis. 1 An infant vaccine programme against meningococcal capsular group B Neisseria meningitidis (MenB) was launched from 1st September with an aim to reduce endemic MenB disease in early childhood. On 1st August 2015, an adolescent programme against groups A, C, W and Y meningococci (MenACWY) was rolled out to halt a growing outbreak of capsular group W disease (MenW) caused by a hypervirulent clone of N. meningitidis, in addition to maintaining control against MenC disease provided by the current adolescent programme. 2. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/
Corrosion behaviour of Nd-Fe-B permanent magnets
International Nuclear Information System (INIS)
Mummert, K.; El-Aziz, A.M.; Barkleit, G.; Schultz, L.; Rodewald, W.
2000-01-01
The corrosion behaviour of Nd-Fe-B permanent magnetic alloys as well as of single phases of these alloys have been investigated in sulphuric acid at room temperature and humid air at 150 C using mass loss and electrochemical techniques. Scanning electron microscopy and scanning probe microscopy were used to study the surface topography. The electrostatic surface potential was examined by scanning probe microscopy using tapping mode. A correlation between the electrostatic surface potential and the corrosion rate of these alloys was found. The higher the value of the electrostatic surface potential of the intergranular phases the higher is the corrosion sensitivity. The strength of the corrosion attack on the phases of sintered permanent magnetic alloys is as follows: Ferromagnetic phase < B-rich phase < Nd-rich phase. The differences in the chemical composition as well as in the preparation of these magnetic alloys have distinct influence on the corrosion resistance of the magnetic Nd-Fe-B alloys. (orig.)
Directory of Open Access Journals (Sweden)
Jesse B. Therien
2017-07-01
Full Text Available The first generation of biochemical studies of complex, iron-sulfur-cluster-containing [FeFe]-hydrogenases and Mo-nitrogenase were carried out on enzymes purified from Clostridium pasteurianum (strain W5. Previous studies suggested that two distinct [FeFe]-hydrogenases are expressed differentially under nitrogen-fixing and non-nitrogen-fixing conditions. As a result, the first characterized [FeFe]-hydrogenase (CpI is presumed to have a primary role in central metabolism, recycling reduced electron carriers that accumulate during fermentation via proton reduction. A role for capturing reducing equivalents released as hydrogen during nitrogen fixation has been proposed for the second hydrogenase, CpII. Biochemical characterization of CpI and CpII indicated CpI has extremely high hydrogen production activity in comparison to CpII, while CpII has elevated hydrogen oxidation activity in comparison to CpI when assayed under the same conditions. This suggests that these enzymes have evolved a catalytic bias to support their respective physiological functions. Using the published genome of C. pasteurianum (strain W5 hydrogenase sequences were identified, including the already known [NiFe]-hydrogenase, CpI, and CpII sequences, and a third hydrogenase, CpIII was identified in the genome as well. Quantitative real-time PCR experiments were performed in order to analyze transcript abundance of the hydrogenases under diazotrophic and non-diazotrophic growth conditions. There is a markedly reduced level of CpI gene expression together with concomitant increases in CpII gene expression under nitrogen-fixing conditions. Structure-based analyses of the CpI and CpII sequences reveal variations in their catalytic sites that may contribute to their alternative physiological roles. This work demonstrates that the physiological roles of CpI and CpII are to evolve and to consume hydrogen, respectively, in concurrence with their catalytic activities in vitro, with Cp
Therien, Jesse B.; Artz, Jacob H.; Poudel, Saroj; Hamilton, Trinity L.; Liu, Zhenfeng; Noone, Seth M.; Adams, Michael W. W.; King, Paul W.; Bryant, Donald A.; Boyd, Eric S.; Peters, John W.
2017-01-01
The first generation of biochemical studies of complex, iron-sulfur-cluster-containing [FeFe]-hydrogenases and Mo-nitrogenase were carried out on enzymes purified from Clostridium pasteurianum (strain W5). Previous studies suggested that two distinct [FeFe]-hydrogenases are expressed differentially under nitrogen-fixing and non-nitrogen-fixing conditions. As a result, the first characterized [FeFe]-hydrogenase (CpI) is presumed to have a primary role in central metabolism, recycling reduced electron carriers that accumulate during fermentation via proton reduction. A role for capturing reducing equivalents released as hydrogen during nitrogen fixation has been proposed for the second hydrogenase, CpII. Biochemical characterization of CpI and CpII indicated CpI has extremely high hydrogen production activity in comparison to CpII, while CpII has elevated hydrogen oxidation activity in comparison to CpI when assayed under the same conditions. This suggests that these enzymes have evolved a catalytic bias to support their respective physiological functions. Using the published genome of C. pasteurianum (strain W5) hydrogenase sequences were identified, including the already known [NiFe]-hydrogenase, CpI, and CpII sequences, and a third hydrogenase, CpIII was identified in the genome as well. Quantitative real-time PCR experiments were performed in order to analyze transcript abundance of the hydrogenases under diazotrophic and non-diazotrophic growth conditions. There is a markedly reduced level of CpI gene expression together with concomitant increases in CpII gene expression under nitrogen-fixing conditions. Structure-based analyses of the CpI and CpII sequences reveal variations in their catalytic sites that may contribute to their alternative physiological roles. This work demonstrates that the physiological roles of CpI and CpII are to evolve and to consume hydrogen, respectively, in concurrence with their catalytic activities in vitro, with CpII capturing excess
Enhancement in (BHmax of PLD-made isotropic Nd-Fe-B thick film magnets deposited on Si substrates
Directory of Open Access Journals (Sweden)
M. Nakano
2017-05-01
Full Text Available Increase in Nd contents of a PLD-made isotropic Nd-Fe-B thick-film magnet enabled us to enhance the thickness of the film magnet deposited on a Si substrate because the linear expansion coefficient of Nd is an intermediate value between Nd2Fe14B and Si. The large amount of Nd, however, degraded the residual magnetic polarization and (BHmax. In the study, we reduced the Nd contents of each Nd-Fe-B film by inserting a Nd or a Nd-rich Nd-Fe-B buffer layer between a Nd-Fe-B film and a Si substrate in order to suppress the mechanical destruction together with the improvement in magnetic properties. It was found that the mechanical property of a Nd-Fe-B film comprising the Nd-Fe-B buffer layer in the thickness range from 10 to 60 μm was superior than that of a sample with the Nd buffer layer. Resultantly, an average (BHmax value of Nd-Fe-B films with each Nd-Fe-B buffer layer deposited on Si substrates could be enhanced by approximately 15 kJ/m3 compared to that of non-buffer-layered films.
Phase analysis of Fe-B-V system
Czech Academy of Sciences Publication Activity Database
Homolová, V.; Výrostková, A.; Čiripová, L.; Kroupa, Aleš
2013-01-01
Roč. 51, č. 2 (2013), s. 135-139 ISSN 0023-432X R&D Projects: GA ČR(CZ) GAP108/10/1908 Institutional support: RVO:68081723 Keywords : CALPHAD method * Fe-B-V system * phase diagram Subject RIV: BJ - Thermodynamics Impact factor: 0.546, year: 2013
Miniature Scroll Pumps Fabricated by LIGA
Wiberg, Dean; Shcheglov, Kirill; White, Victor; Bae, Sam
2009-01-01
Miniature scroll pumps have been proposed as roughing pumps (low - vacuum pumps) for miniature scientific instruments (e.g., portable mass spectrometers and gas analyzers) that depend on vacuum. The larger scroll pumps used as roughing pumps in some older vacuum systems are fabricated by conventional machining. Typically, such an older scroll pump includes (1) an electric motor with an eccentric shaft to generate orbital motion of a scroll and (2) conventional bearings to restrict the orbital motion to a circle. The proposed miniature scroll pumps would differ from the prior, larger ones in both design and fabrication. A miniature scroll pump would include two scrolls: one mounted on a stationary baseplate and one on a flexure stage (see figure). An electromagnetic actuator in the form of two pairs of voice coils in a push-pull configuration would make the flexure stage move in the desired circular orbit. The capacitance between the scrolls would be monitored to provide position (gap) feedback to a control system that would adjust the drive signals applied to the voice coils to maintain the circular orbit as needed for precise sealing of the scrolls. To minimize power consumption and maximize precision of control, the flexure stage would be driven at the frequency of its mechanical resonance. The miniaturization of these pumps would entail both operational and manufacturing tolerances of pump components. In addition, the vibrations of conventional motors and ball bearings exceed these tight tolerances by an order of magnitude. Therefore, the proposed pumps would be fabricated by the microfabrication method known by the German acronym LIGA ( lithographie, galvanoformung, abformung, which means lithography, electroforming, molding) because LIGA has been shown to be capable of providing the required tolerances at large aspect ratios.
Measurements on very small single crystals of NdFeB using a vibrating reed magnetometer
International Nuclear Information System (INIS)
Richter, H.J.; Hempel, K.A.; Verhoef, R.
1988-01-01
Nd 2 Fe 14 B single crystals with magnetic moments ranging from 1.6 x 10 -8 Acm 2 to 9.5 x 10 -7 Acm 2 are measured using the ultra high sensitivity vibrating reed magnetometer. The hysteresis loops are compared to those of BaFe 12 O 19 single crystals. It turns out that the magnetization reversal of the Nd 2 Fe 14 B samples is similar to that of BaFe 12 O 19 single crystals if the ferrite samples are considerably bigger in size. This does not hold for bigger Nd 2 Fe 14 B particles where stronger domain wall pinning is observed. For very small grains of Nd 2 Fe 14 B there is still evidence of domain wall processes while for BaFe 12 O 19 grains of the same size true single domain behaviour can be observed
Methods of characterization of multiphase Nd-Fe-B melt-spun alloys
Directory of Open Access Journals (Sweden)
Grujić A.
2007-01-01
Full Text Available Nanocomposite permanent magnetic materials based on Nd-Fe-B alloys with a low Nd content are a new type of permanent magnetic material. The microstructure of these nanocomposite permanent magnets is composed of a mixture of magnetically soft and hard phases providing the so called exchange coupling effect. Beside the optimization process parameters, methods of characterization have a very important role in the design of an optimal magnetic matrix of multiphase melt-spun Nd-Fe-B alloys. Different methods and techniques of characterization were used for observation and study of the microstructure evolution during crystallization. A summary results of measurements using different methods of characterization are presented to enable a better insight into relations between the microstructure and magnetic properties of the investigated melt-spun Nd-Fe-B alloys. .
Fabrication of miniaturized electrostatic deflectors using LIGA
International Nuclear Information System (INIS)
Jackson, K.H.; Khan-Malek, C.; Muray, L.P.
1997-01-01
Miniaturized electron beam columns (open-quotes microcolumnsclose quotes) have been demonstrated to be suitable candidates for scanning electron microscopy (SEM), e-beam lithography and other high resolution, low voltage applications. In the present technology, microcolumns consist of open-quotes selectively scaledclose quotes micro-sized lenses and apertures, fabricated from silicon membranes with e-beam lithography, reactive ion beam etching and other semiconductor thin-film techniques. These miniaturized electron-optical elements provide significant advantages over conventional optics in performance and ease of fabrication. Since lens aberrations scale roughly with size, it is possible to fabricate simple microcolumns with extremely high brightness sources and electrostatic objective lenses, with resolution and beam current comparable to conventional e-beam columns. Moreover since microcolumns typically operate at low voltages (1 KeV), the proximity effects encountered in e-beam lithography become negligible. For high throughput applications, batch fabrication methods may be used to build large parallel arrays of microcolumns. To date, the best reported performance with a 1 keV cold field emission cathode, is 30 nm resolution at a working distance of 2mm in a 3.5mm column. Fabrication of the microcolumn deflector and stigmator, however, have remained beyond the capabilities of conventional machining operations and semiconductor processing technology. This work examines the LIGA process as a superior alternative to fabrication of the deflectors, especially in terms of degree of miniaturization, dimensional control, placement accuracy, run-out, facet smoothness and choice of suitable materials. LIGA is a combination of deep X-ray lithography, electroplating, and injection molding processes which allow the fabrication of microstructures
A LigA three-domain region protects hamsters from lethal infection by Leptospira interrogans.
Directory of Open Access Journals (Sweden)
Mariana L Coutinho
2011-12-01
Full Text Available The leptospiral LigA protein consists of 13 bacterial immunoglobulin-like (Big domains and is the only purified recombinant subunit vaccine that has been demonstrated to protect against lethal challenge by a clinical isolate of Leptospira interrogans in the hamster model of leptospirosis. We determined the minimum number and location of LigA domains required for immunoprotection. Immunization with domains 11 and 12 was found to be required but insufficient for protection. Inclusion of a third domain, either 10 or 13, was required for 100% survival after intraperitoneal challenge with Leptospira interrogans serovar Copenhageni strain Fiocruz L1-130. As in previous studies, survivors had renal colonization; here, we quantitated the leptospiral burden by qPCR to be 1.2×10(3 to 8×10(5 copies of leptospiral DNA per microgram of kidney DNA. Although renal histopathology in survivors revealed tubulointerstitial changes indicating an inflammatory response to the infection, blood chemistry analysis indicated that renal function was normal. These studies define the Big domains of LigA that account for its vaccine efficacy and highlight the need for additional strategies to achieve sterilizing immunity to protect the mammalian host from leptospiral infection and its consequences.
Magnetic and transport properties of La0.3Ca0.7Mn0.9T0.1O3 (T = Cr, Fe, and W)
International Nuclear Information System (INIS)
Sudyoadsuk, T.; Suryanarayanan, R.; Winotai, P.
2005-01-01
We have carried out structural, magnetic and magneto transport measurements of the electron-doped manganite La 0.3 Ca 0.7 MnO 3 substituted with 10% of Cr, Fe and W on the Mn site. The substitution by Cr, Fe and W suppresses the charge order transition present at 260 K in the parent compound. All the samples show a semiconducting behavior. Whereas the parent compound does not show any magneto resistance (MR) even in a field of 14 T, a maximum MR of 6% in 5 T at 25 K is observed for the Cr substituted sample that is attributed to a spin-cluster glass like states induced by Cr. The Fe and W substituted samples showed a MR of 1.5 and 3%, respectively which may be attributed to a smaller number of FM domains/spin-clusters and to an increase in anti-ferromagnetic interaction
Study of high-coercivity sintered NdFeB magnets
Energy Technology Data Exchange (ETDEWEB)
Bai, G. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China); Department of Mathematics and Physics, Xi' an Institute of Technology, Xi' an, 710032 (China); Gao, R.W. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China)]. E-mail: gaorwbox@sdu.edu.cn; Sun, Y. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China); Han, G.B. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China); Wang, B. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China); Baotou Rare Earth Research Institute, Batou 014030 (China)
2007-01-15
Magnetic powders for sintered NdFeB magnets have been prepared by using an advanced processing method including strip casting, hydrogen decrepitation, jet milling and rubber isotropic press. The effects of Dy, Ga and Co addition on the microstructure and magnetic properties of sintered magnets have been investigated. By adopting a suitable component ratio and adjusting proper technological parameters, we have prepared high-coercivity sintered NdFeB magnets with hard magnetic properties of {sub j} H {sub c}=25.6 kOe, B {sub r}=13.2 kG and (BH){sub max}=39.9 MGOe. The temperature coefficient of coercivity of the magnets (between 20 and 150 deg. C) is -0.53% deg. C. The magnetic properties at high temperature satisfy the needs of permanent magnet motors.
Lavrentyev, A. A.; Gabrelian, B. V.; Vu, Tuan V.; Isaenko, L. I.; Yelisseyev, A. P.; Khyzhun, O. Y.
2018-06-01
Measurements of X-ray photoelectron core-level and valence-band spectra for pristine and irradiated with Ar+ ions surfaces of LiGa0.5In0.5Se2 single crystal, novel nonlinear optical mid-IR selenide grown by a modified vertical Bridgman-Stockbarger technique, are reported. Electronic structure of LiGa0.5In0.5Se2 is elucidated from theoretical and experimental points of view. Notably, total and partial densities of states (DOSs) of the LiGa0.5In0.5Se2 compound are calculated based on density functional theory (DFT) using the augmented plane wave + local orbitals (APW + lo) method. In accordance with the DFT calculations, the principal contributors to the valence band are the Se 4p states, making the main input at the top and in the upper part of the band, while its bottom is dominated by contributions of the valence s states associated with Ga and In atoms. The theoretical total DOS curve peculiarities are found to be in excellent agreement with the shape of the X-ray photoelectron valence-band spectrum of the LiGa0.5In0.5Se2 single crystal. The bottom of the conduction band of LiGa0.5In0.5Se2 is formed mainly by contributions of the unoccupied Ga 4s and In 5s states in almost equal proportion, with somewhat smaller contributions of the unoccupied Se 4p states as well. Our calculations indicate that the LiGa0.5In0.5Se2 compound is a direct gap semiconductor. The principal optical constants of LiGa0.5In0.5Se2 are calculated in the present work.
Intermediate phases in the hydrogen disproportionated state of NdFeB-type powders
International Nuclear Information System (INIS)
Yi, G.; Chapman, J. N.; Brown, D. N.; Harris, I. R.
2001-01-01
Transmission electron microscopy studies have been carried out on partially disproportionated NdFeB-type alloys. A new intermediate magnetic (NIM) phase has been identified. Moreover, the lamella structure which subsequently develops from the tetragonal NIM phase comprises a tetragonal NdFe-containing (IL) phase and α-Fe. The experimental data show strong evidence of a well-defined crystallographic relation between both the NIM and lamella phases and between the IL phase and α-Fe. These observations give insight into how crystallographic texture, and hence anisotropy, can be developed in NdFeB-type powders processed by the hydrogenation, disproportionation, desorption, and recombination route. copyright 2001 American Institute of Physics
Direct Iron Coating onto Nd-Fe-B Powder by Thermal Decomposition of Iron Pentacarbonyl
International Nuclear Information System (INIS)
Yamamuro, S; Okano, M; Tanaka, T; Sumiyama, K; Nozawa, N; Nishiuchi, T; Hirosawa, S; Ohkubo, T
2011-01-01
Iron-coated Nd-Fe-B composite powder was prepared by thermal decomposition of iron pentacarbonyl in an inert organic solvent in the presence of alkylamine. Though this method is based on a modified solution-phase process to synthesize highly size-controlled iron nanoparticles, it is in turn featured by a suppressed formation of iron nanoparticles to achieve an efficient iron coating solely onto the surfaces of rare-earth magnet powder. The Nd-Fe-B magnetic powder was successfully coated by iron shells whose thicknesses were of the order of submicrometer to micrometer, being tuneable by the amount of initially loaded iron pentacarbonyl in a reaction flask. The amount of the coated iron reached to more than 10 wt.% of the initial Nd-Fe-B magnetic powder, which is practically sufficient to fabricate Nd-Fe-B/α-Fe nanocomposite permanent magnets.
Coercivity enhancement in Nd-Fe-B sintered permanent magnet by Dy nanoparticles doping
Energy Technology Data Exchange (ETDEWEB)
Liu, W.Q., E-mail: liuweiqiang77@hotmail.co [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Sun, H. [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Yi, X.F. [Anhui Earth-panda Advance Magnetic Material Co., Ltd., Anhui 231500 (China); Liu, X.C.; Zhang, D.T. [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Yue, M., E-mail: yueming@bjut.edu.c [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Zhang, J.X. [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China)
2010-07-02
Nd-Fe-B permanent magnets with a small amount of Dysprosium (Dy) nanoparticles doping were prepared by conventional sintered method, and the microstructure and magnetic properties of the magnets were studied. Investigation shows that the coercivity rises gradually, while the remanence decreases simultaneously with increased Dy doping amount. As a result, the magnet with 1.5 wt.% Dy exhibits optimal magnetic properties. Further investigation presumed that Dy is enriched as (Nd, Dy){sub 2}Fe{sub 14}B phase in the surface region of the Nd{sub 2}Fe{sub 14}B matrix grains indicated by the enhancement of the magneto-crystalline anisotropy field of the Nd{sub 2}Fe{sub 14}B phase. As a result, the magnet doped with a small amount of Dy nanoparticles possesses remarkably enhanced coercivity without sacrificing its magnetization noticeably.
Spacer layer effect and microstructure on multi-layer [NdFeB/Nb]n films
International Nuclear Information System (INIS)
Tsai, J.-L.; Yao, Y.-D.; Chin, T.-S.; Kronmueller, H.
2002-01-01
Spacer layer effect on multi-layer [NdFeB/Nb] n films has been investigated from the variation of magnetic properties and microstructure of the films. From a HRTEM cross-section view observation, the average grain size of [NdFeB/Nb] n multi-layers was controlled by both annealing temperature and thickness of NdFeB layer. Selected area diffraction pattern indicated that the structure of Nb spacer layer was amorphous. The grain size and coercivity of [NdFeB x /Nb] n films change from 50 nm and 16.7 kOe to 167 nm and 9 kOe for films with x=40 nm, n=10 and x=200 nm, n=2, respectively
Coercivity of Nd-Fe-B hot-deformed magnets produced by the spark plasma sintering method
Directory of Open Access Journals (Sweden)
Tetsuji Saito
2017-05-01
Full Text Available The effects of Nd-Cu alloy powder addition on the microstructures and magnetic properties of Nd-Fe-B hot-deformed magnets produced by the spark plasma sintering (SPS method were investigated. The addition of a small amount of Nd-Cu alloy powder, up to 2%, significantly increased the coercivity of the Nd-Fe-B hot-deformed magnets without deteriorating the crystallographic alignment of the Nd2Fe14B phase. The Nd-Fe-B hot-deformed magnet with 2% Nd-Cu alloy powder had the same remanence value as the Nd-Fe-B hot-deformed magnet without Nd-Cu alloy powder addition, but the magnet with 2% Nd-Cu alloy powder exhibited higher coercivity and a higher maximum energy product than the magnet without Nd-Cu alloy powder addition.
Energy Technology Data Exchange (ETDEWEB)
Treadwell, LaRico J.; Watkins-Curry, Pilanda [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Department of Chemistry, University of Texas at Dallas, Richardson, TX 75080 (United States); McAlpin, Jacob D. [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Prestigiacomo, Joseph; Stadler, Shane [Department of Physics and Astronomy, Louisiana State University, Baton Rouge, LA 70803 (United States); Chan, Julia Y., E-mail: Julia.Chan@utdallas.edu [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Department of Chemistry, University of Texas at Dallas, Richardson, TX 75080 (United States)
2014-02-15
The synthesis and characterization of Mn- and Fe-substituted Ln{sub 6}W{sub 4}Al{sub 43} (Ln=Gd, Yb) and Yb{sub 6}Ti{sub 4}Al{sub 43} are reported. The compounds adopt the Ho{sub 6}Mo{sub 4}Al{sub 43} structure type with lattice parameters of a∼11 Å and c∼17.8 Å with structural site preferences for Mn and Fe. The magnetization of Yb{sub 6}W{sub 4}Al{sub 43} is sensitive to Mn and Fe doping, which is evident by an increase in the field dependent magnetization. Gd{sub 6}W{sub 4}Al{sub 43}, Gd{sub 6}W{sub 4}Al{sub 42.31(11)}Mn{sub 0.69(11)}, and Gd{sub 6}W{sub 4}Al{sub 41.69(12)}Fe{sub 1.30(12)} order antiferromagnetically in the ab- and c-directions at 15, 14, and 13 K, respectively, with positive Weiss constants, suggesting the presence of ferromagnetic exchange interactions. Anisotropic magnetization data of Gd{sub 6}W{sub 4}Al{sub 43−y}T{sub y} (T=Mn, Fe) analogs are discussed. - Graphical abstract: The magnetic susceptibility of Ln{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} (Ln = Gd, Yb; T= Mn, Fe). Display Omitted - Highlights: • Single crystals of Ln{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} were grown with Al-flux. • Anisotropic magnetic behavior were determined on single crystals. • Gd{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} (T=Mn, Fe) analogs order antiferromagnetically.
Energy Technology Data Exchange (ETDEWEB)
Liang, Liping; Ma, Tianyu, E-mail: maty@zju.edu.cn; Zhang, Pei; Jin, Jiaying; Yan, Mi, E-mail: mse_yanmi@zju.edu.cn
2014-04-15
To improve coercivity without sacrificing other magnetic performance of NdFeB sintered magnets, a low melting point Dy{sub 32.5}Fe{sub 62}Cu{sub 5.5} alloy was introduced as an intergranular additive. Magnetic properties and microstructure of the magnets with different Dy{sub 32.5}Fe{sub 62}Cu{sub 5.5} contents were studied. At the optimum addition of 3 wt%, coercivity H{sub cj} was enhanced from 12.7 to 15.2 kOe, the maximum magnetic energy product (BH){sub max} was simultaneously increased from 46.6 to 47.8 MG Oe, accompanied by a slight reduction in remanence B{sub r}. Further investigation on microstructure and grain boundary composition indicated that the enhanced H{sub cj} and (BH){sub max} could be attributed to the refined and uniform 2:14:1 phase grains, continuous grain boundaries and a (Nd,Dy){sub 2}Fe{sub 14}B hardening shell surrounding the 2:14:1 phase grains. - Highlights: • Low melting-point Dy{sub 32.5}Fe{sub 62}Cu{sub 5.5} alloy was introduced to NdFeB magnets. • The doped magnet exhibits enhanced coercivity and maximum energy product. • (Nd,Dy){sub 2}Fe{sub 14}B shell was expected to form in the surface of Nd{sub 2}Fe{sub 14}B grains. • The continuous grain boundary layer formed between neighboring Nd{sub 2}Fe{sub 14}B grains.
Microstructure of Fe-Cr-C hardfacing alloys with additions of Nb, Ti and, B
International Nuclear Information System (INIS)
Berns, H.; Fischer, A.
1987-01-01
The abrasive wear of machine parts and tools used in the mining, earth moving, and transporting of mineral materials can be lowered by filler wire welding of hardfacing alloys. In this paper, the microstructures of Fe-Cr-C and Fe-Cr-C-Nb/Ti hardfacing alloys and deposits and those of newly developed Fe-Cr-C-B and Fe-Ti-Cr-C-B ones are described. They show up to 85 vol.% of primarily solidified coarse hard phases; i.e., Carbides of MC-, M/sub 7/C/sub 3/-, M/sub 3/C-type and Borides of MB/sub 2/-, M/sub 3/B/sub 2/-, M/sub 2/B-, M/sub 3/B-, M/sub 23/B/sub 6/-type, which are embedded in a hard eutectic. This itself consists of eutectic hard phases and a martensitic or austenitic metal matrix. The newly developed Fe-Cr-C-B alloys reach hardness values of up to 1200 HV and are harder than all purchased ones. The primary solidification of the MB/sub 2/-type phase of titanium requires such high amounts of titanium and boron that these alloys are not practical for manufacture as commercial filler wires
Directory of Open Access Journals (Sweden)
Huynh X.-K.
2017-06-01
Full Text Available The in situ formation of TiB2 particulates via an interface reaction between Ti and FeB powders was studied. The effects of mechanical activation by high-energy milling on the decomposition of TiH2 and the interface reactions between Ti and FeB powders to form TiB2 were investigated. Powder mixtures were fabricated using planetary ball-milling under various milling conditions. The specific ball-milling energy was calculated from the measured electrical power consumption during milling process. High specific milling energy (152.6 kJ/g resulted in a size reduction and homogeneous dispersion of constituent powders. This resulted in a decrease in the decomposition temperature of TiH2 and an increase in the formation reaction of TiB2 particulates in the Fe matrix, resulting in a homogeneous microstructure of nanoscale TiB2 evenly distributed within the Fe matrix. In contrast, the powder mixture milled with low specific milling energy (36.5 kJ/g showed an inhomogeneous microstructure composed of relatively large Fe-Fe2B particles surrounded by a thin layer of Fe-TiB2 within a finely dispersed Fe-TiB2 matrix region.
Directory of Open Access Journals (Sweden)
Carolina Rodrigues Costa
2011-12-01
estudo, os efeitos de agentes antifúngicos como o fluconazol e o itraconazol sobre a formação de hifas e caracterização genotípica de isolados de C. albicans suscetíveis ou resistentes foram investigados. MÉTODOS: A produção de hifas de cinco isolados de C. albicans, sob a ação de antifúngicos foi investigada pelo cultivo da levedura em meios de crescimento e de indução de hifas. A caracterização genotípica foi realizada para 13 isolados de C. albicans pelo método de RAPD-PCR. RESULTADOS: A análise do dimorfismo mostrou que a formação de hifas foi maior nos isolados resistentes do que nos suscetíveis aos antifúngicos. O método de RAPD-PCR identificou a formação de dois diferentes grupos. No grupo A, foram agrupados quatro isolados resistentes e dois suscetíveis e no grupo B um resistente e seis suscetíveis. CONCLUSÕES: Considerando que a formação hifal foi maior em isolados resistentes na presença de azólicos, concluimos que a produção hifal está muito relacionada a suscetibilidade a estes fámacos. Estes antifúngicos podem alterar a morfologia de C. albicans em dependência da sua suscetibilidade. No método de RAPD-PCR, o encontro da maioria dos isolados resistentes classificados como pertencentes ao grupo A e suscetíveis ao grupo B demonstrou que este método apresentou um padrão semelhante entre os dois grupos, sugerindo que por este método pode ser detectado uma estreita correlação entre genótipos e amostras resistentes ao fluconazol.
Exploring high-pressure FeB{sub 2}: Structural and electronic properties predictions
Energy Technology Data Exchange (ETDEWEB)
Harran, Ismail [School of Physical Science and Technology, Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, Southwest Jiaotong University, Chengdu, 610031 (China); Al Fashir University (Sudan); Wang, Hongyan [School of Physical Science and Technology, Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, Southwest Jiaotong University, Chengdu, 610031 (China); Chen, Yuanzheng, E-mail: cyz@calypso.org.cn [School of Physical Science and Technology, Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, Southwest Jiaotong University, Chengdu, 610031 (China); Jia, Mingzhen [School of Physical Science and Technology, Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, Southwest Jiaotong University, Chengdu, 610031 (China); Wu, Nannan [School of Mathematics, Physics and Biological Engineering, Inner Mongolia University of Science & Technology, Baotou, 014010 (China)
2016-09-05
The high pressure (HP) structural phase of FeB{sub 2} compound is investigated by using first-principles crystal structure prediction based on the CALYPSO technique. A thermodynamically stable phase of FeB{sub 2} with space group Imma is predicted at pressure above 225 GPa, which is characterized by a layered orthorhombic structure containing puckered graphite-like boron layers. Its electronic and mechanical properties are identified and analyzed. The feature of band structures favors the occurrence of superconductivity, whereas, the calculated Pugh's ratio reveals that the HP Imma structure exhibits ductile mechanical property. - Highlights: • The high pressure structural phase of FeB{sub 2} compound is firstly investigated by the CALYPSO technique. • A thermodynamically stable Imma phase of FeB{sub 2} is predicted at pressure above 225 GPa. • The Imma structure is characterized by a 2D boron network containing puckered graphite-like boron layers. • The band feature of Imma structure favors the occurrence of superconductivity. • The calculated Pugh's ratio suggests that the Imma structure exhibits ductile mechanical property.
Microstructure Formation in Strip-Cast RE-Fe-B Alloys for Magnets
Yamamoto, Kazuhiko; Matsuura, Masashi; Sugimoto, Satoshi
2017-07-01
During the manufacturing of sintered NdFeB magnets, it is well known that the microstructure of the starting alloy has a strong influence on the processing and the magnetic properties of the product. In this study, we clarify the microstructure formation in strip-cast rare earth (R)-Fe-B alloys used to produce magnets. The microstructure of the alloy surface in contact with the cooling roll and its cross-section were observed using laser microscopy, field emission electron microprobe analysis, and transmission electron microscopy. The orientations of crystal grains were determined by X-ray diffraction and electron backscatter diffraction analyses. Petal-shaped structures were found to cover the alloy surface in contact with the cooling roll, each consisting of a central nucleation region and radially grown Nd2Fe14B dendritic structures. The nucleation region, consisting of a "disc" and "predendrites", occurs in the super-cooled region of the contact area between the cooling roll and melt. In the disc region, spherical Nd2Fe14B particles in the thickness direction increase in volume. These discs and predendrites observed in the super-cooled area negatively influence the magnetic orientation and sinterability in the produced magnets. Therefore, it is important to avoid excessive super-cooling to obtain optimum magnetic properties.
International Nuclear Information System (INIS)
Davalos, J.; Marco, J.F.; Gracia, M.; Gancedo, J.R.; Greneche, J.M.
1990-01-01
ICEMS, XPS, XRD, and AES have been used to study the corrosion layers formed on two metallic glasses, Fe 80 B 20 and Fe 40 Ni 40 (MoB) 20 (2605 and 2826 MB, Allied Company), exposed to an SO 2 -polluted humid atmosphere. The iron-containing corrosion products are the same found for pure iron in the same environment, but different relative concentrations were clearly evidenced by ICEMS results. Elemental sulphur, Ni(OH) 2 , and B(OH) 3 , the latter enriched at the surface, were found by XPS, XRD and AES. (orig.)
International Nuclear Information System (INIS)
Sidorov, V.A.; Khvostantsev, L.G.
1994-01-01
The relative volume change and the initial ac-susceptibility have been measured for Fe 65 Ni 35 and Er 2 Fe 14 B under hydrostatic pressure up to 8.5 GPa at room temperature. The bulk modulus of Fe 65 Ni 35 begins to rise and the susceptibility begins to drop at 3.5-4 GPa, indicating the continuous disappearance of ferromagnetism at high pressure. The transition from ferromagnetic to paramagnetic state in Er 2 Fe 14 B at 5.7 GPa is more abrupt and the giant (order of magnitude) softening of the bulk modulus is observed before this transition. The spin reorientation (SR) transition in Er 2 Fe 14 B shifts under pressure to lower temperatures (dT SR /dP = -19 K/GPa). (orig.)
Wet-chemical synthesis of nanoscale iron boride, XAFS analysis and crystallisation to α-FeB.
Rades, Steffi; Kornowski, Andreas; Weller, Horst; Albert, Barbara
2011-06-20
The reaction of lithium tetrahydridoborate and iron bromide in high boiling ether as reaction medium produces an ultrafine, pyrophoric and magnetic precipitate. X-ray and electron diffraction proved the product to be amorphous. According to X-ray absorption fine structure spectroscopy (XAFS) the precipitate has FeB structure up to nearly two coordination spheres around an iron absorber atom. Transmission electron microscopy (TEM) confirms the ultrafine powder to be nanoscale. Subsequent annealing at 450 °C causes the atoms to arrange in a more distinct FeB structure, and further thermal treatment to 1050 °C extends the local structure to the α-modification of FeB. Between 1050 °C and 1500 °C α-FeB is transformed into β-FeB. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
International Nuclear Information System (INIS)
Suprapedi; Sardjono, P.; Muljadi
2016-01-01
The magnet permanent has been made by using NdFeB (NQP-B) powder with purity 99.90% and polymer rubber with purity 90%. This research was done to determine the effect of the polymer (rubber) composition as binder in the manufacture of bonded magnet NdFeB on physical properties, microstructure and magnetic properties. Bonded magnets are magnet material made from a mixture of magnetic powder as a filler and the polymer as a matrix material or as binder to bind the magnetic particles. The NdFeB (NQP-B) powder fractions of bonded magnets NdFeB investigated were as follows: a) 97 wt.% of NdFeB (NQP-B) and 3 wt.% of rubber,b) 95wt.% of NdFeB (NQP-B) and 5 wt.% of rubber, c) 93 wt.% of NdFeB (NQP-B) and 7 wt.% of rubber, d) 91 wt.% of NdFeB (NQP-B) and 9 wt.% of rubber. Both raw materials were mixed by using mixer until homogen with total weight about 16 g for each sample, then added 0.3 ml of catalyst and mixed again and put in dies mould and compacted at pressure 30 MPa, then dried for 2 hours at room temperature. The dried samples was characterized such as: bulk density measurement and magnetic properties by using BH-curve permeagraph. The bulk density values of the sample bonded NdFeB magnets using the binder 3% wt. and 5% wt. rubber are respectively 4,70 g/cm 3 and 4.88 g/cm 3 . The result from BH- curve shows that the highest value of remanence (Br = 5.12 kGauss) is at sample with 3% wt. of rubber, but sample with 5% wt. of rubber has lowest value of remanance (Br = 4.40 kGauss). Based on the observation of the SEM photograph shown that the rubber material has been successfully covered the whole surface of the grain and fill some of the voids that are in the grain boundary. (paper)
Suprapedi; Sardjono, P.; Muljadi
2016-11-01
The magnet permanent has been made by using NdFeB (NQP-B) powder with purity 99.90% and polymer rubber with purity 90%. This research was done to determine the effect of the polymer (rubber) composition as binder in the manufacture of bonded magnet NdFeB on physical properties, microstructure and magnetic properties. Bonded magnets are magnet material made from a mixture of magnetic powder as a filler and the polymer as a matrix material or as binder to bind the magnetic particles. The NdFeB (NQP-B) powder fractions of bonded magnets NdFeB investigated were as follows: a) 97 wt.% of NdFeB (NQP-B) and 3 wt.% of rubber,b) 95wt.% of NdFeB (NQP-B) and 5 wt.% of rubber, c) 93 wt.% of NdFeB (NQP-B) and 7 wt.% of rubber, d) 91 wt.% of NdFeB (NQP-B) and 9 wt.% of rubber. Both raw materials were mixed by using mixer until homogen with total weight about 16 g for each sample, then added 0.3 ml of catalyst and mixed again and put in dies mould and compacted at pressure 30 MPa, then dried for 2 hours at room temperature. The dried samples was characterized such as: bulk density measurement and magnetic properties by using BH-curve permeagraph. The bulk density values of the sample bonded NdFeB magnets using the binder 3% wt. and 5% wt. rubber are respectively 4,70 g/cm3 and 4.88 g/cm3. The result from BH- curve shows that the highest value of remanence (Br = 5.12 kGauss) is at sample with 3% wt. of rubber, but sample with 5% wt. of rubber has lowest value of remanance (Br = 4.40 kGauss). Based on the observation of the SEM photograph shown that the rubber material has been successfully covered the whole surface of the grain and fill some of the voids that are in the grain boundary.
International Nuclear Information System (INIS)
Habib, K.; Abdullah, A.
1995-01-01
An electrochemical study on Fe-Co-B-Si amorphous electrodes has been conducted. The study was focused on determining the electrochemical impedance spectroscopy (EIS) of four different alloys of Fe-Co-B-Si in various HCl acid solutions. The A.C. impedance and the capacitance of Fe-Co-B-Si, Co-Fe-Ni-B-Si, Co-Fe-Mn-B-Si, and Co-Fe-Ni-Mo-B-Si alloys were obtained in 25, 50, 75 and 100% of HCl acid at room temperature. Electrochemical parameters, i.e., impedance, were found to vary depending on additions of the Ni, Mn, Ni-Mo to Fe-Co-B-Si alloy, the acid concentration, and the nanoscopic surface roughness of the electrodes. Consequently, a correlation between the obtained data is established
Low pressure plasma spray deposition of W-Ni-Fe alloy
International Nuclear Information System (INIS)
Mutasim, Z.Z.; Smith, R.W.
1991-01-01
The production of net shape refractory metal structural preforms are increasing in importance in chemical processing, defense and aerospace applications. Conventional methods become limited for refractory metal processing due to the high melting temperatures and fabrication difficulties. Plasma spray forming, a high temperature process, has been shown to be capable of refractory metal powder consolidation in net shape products. The research reported here has evaluated this method for the deposition of heavy tungsten alloys. Plasma Melted Rapidly Solidified (PMRS) W 8%Ni-2%Fe refractory metal powders were spray formed using vacuum plasma spray (VPS) process and produced 99% dense, fine grain and homogeneous microstructures. In this paper plasma operating parameters (plasma arc gas type and flowrate plasma gun nozzle size and spray distance) were studied and their effects on deposit's density and microstructure are reported
El uso de las redes sociales y el engagement de los clubes de la Liga Endesa ACB
Herrera-Torres, L.; Pérez-Tur, F.; García-Fernández, J.; Fernández-Gavira, J.
2017-01-01
Las redes sociales se han convertido en una plataforma idónea para dar a conocer y aumentar la visibilidad de una marca o empresa y también, para interactuar y analizar las acciones de los fans y seguidores de estas. Debido a ello, el presente estudio pretende averiguar las diferentes redes sociales que emplean los clubes de baloncesto de la Liga Endesa ACB, examinar el Engagement de Facebook y Twitter y, analizar si existe una correlación entre la posición en el ranking al final de la liga, ...
Li, Yuqing; Yue, Ming; Zhao, Guoping; Zhang, Hongguo
2018-01-01
The effects of soft phase with different particle sizes and distributions on the Nd2Fe14B/α-Fe nanocomposite magnets have been studied by the micro-magnetism simulation. The calculated results show that smaller and/or scattered distribution of soft phase can benefit to the coercivity (H ci) of the nanocomposite magnets. The magnetization moment evolution during magnetic reversal is systematically analyzed. On the other hand, magnetic properties of anisotropic Nd-Fe-B/α-Fe nanocomposite magnets prepared by hot pressing and hot deformation methods also provide evidences for the calculated results.
Oxygen Non-Stoichiometry and Electrical Conductivity of LA0.2Sr0.8Fe0.8B0.2O3-d, B = Fe, Ti, Ta
Lohne, O.F.; Phung, T.N.; Grande, T.; Bouwmeester, Henricus J.M.; Hendriksen, P.V.; Sogaard, M.; Wiik, K.
2014-01-01
The oxygen non-stoichiometry was determined by coulometric titration for the perovskite oxides La0.2Sr0.8FeO3−δ and La0.2Sr0.8Fe0.8B0.2O3−δ (B = Ti4+ and Ta5+) in the temperature range 600 ◦C ≤ T ≤ 900 ◦C and the oxygen partial pressure range: 1 · 10−15 ≤ pO2 ≤ 0.209 atm. The non-stoichiometry (δ)
Optical spectroscopic study of multiferroic BiFeO3 and LuFe2O4
Xu, Xiaoshan
2010-03-01
Iron-based multiferroics such as BiFeO3 and LuFe2O4 exhibit the highest magnetic and ferroelectric ordering temperatures among known multiferroics. LuFe2O4 is a frustrated system with several phase transitions that result in electronically driven multiferroicity. To understand how this peculiar multiferroic mechanism correlates with magnetism, we studied electronic excitations by optical spectroscopy and other complementary techniques. We show that the charge order, which determines the dielectric properties, is due to the ``order by fluctuation'' mechanism, evidenced by the onset of charge fluctuation well below the charge ordering transition. We also find a low temperature monoclinic distortion driven by both temperature and magnetic field, indicating strong coupling between structure, magnetism and charge order. BiFeO3 is the only known single phase multiferroics with room temperature magnetism and ferroelectricity. To investigate the spin-charge coupling, we measured the optical properties of BiFeO3. We find that the absorption onset occurs due to on-site Fe^3+ excitations at 1.41 and 1.90 eV. Temperature and magnetic-field-induced spectral changes reveal complex interactions between on-site crystal-field and magnetic excitations in the form of magnon sidebands. The sensitivity of the magnon sidebands allows us to map out the magnetic-field temperature phase diagram which demonstrates optical evidence for spin spiral quenching above 20 T and suggests a spin domain reorientation near 10 T. Work done in collaboration with T.V. Brinzari, R.C. Rai, M. Angst, R.P. Hermann, A.D. Christianson, J.-W. Kim, Z. Islam, B.C. Sales, D. Mandrus, S. Lee, Y.H. Chu, L. W. Martin, A. Kumar, R. Ramesh, S.W. Cheong, S. McGill, and J.L. Musfeldt.
International Nuclear Information System (INIS)
Xiaoya, Liu; Yuping, Li; Lianxi, Hu
2013-01-01
The process of mechanically activated disproportionation and desorption-recombination in-situ sintering was proposed to synthesize highly densified nanocrystalline NdFeB magnet, and its validity was demonstrated by experimental investigation with the use of a Nd 16 Fe 76 B 8 (atomic ratio) alloy. Firstly, the as-cast alloy was disproportionated by mechanical milling in hydrogen, with the starting micron-sized Nd 2 Fe 14 B phase decomposed into an intimate mixture of nano-structured NdH 2.7 , Fe 2 B and α-Fe phases. The as-disproportionated alloy powders were compacted by cold pressing and then subjected to desorption-recombination in-situ sintering. The microstructure of both the as-disproportionated and the subsequently sintered samples was characterized by X-ray diffraction and electron transmission microscopy, respectively. The magnetic properties of the sintered samples were measured by using vibrating sample magnetometer. The results showed that, by vacuum sintering, not only was the powder compact consolidated, but also the as-disproportionated microstucture transformed into nanocrystalline Nd 2 Fe 14 B phase via the well-known desorption-recombination reaction, thus giving rise to nanocrystalline NdFeB magnet. In the present study, the optimal sintering parameters were found to be 780 °C×30 min. In this case, the coercivity, the remanence, and maximum energy product of the magnet sample achieved 0.8 T, 635.3 kA/m, and 106.3 kJ/m 3 , respectively. - Highlights: ► Nano-structured disproportionated NdFeB alloy powders by mechanical milling in hydrogen. ► Highly densified green magnet compact by cold pressing of as-disproportionated NdFeB alloy powders. ► Nanocrystalline NdFeB magnets by desorption-recombination in-situ sintering under vacuum. ► Magnetic properties significantly improved by relative density enhancement and nanocrystallization of Nd 2 Fe 14 B phase. ► The effects of sintering parameters on magnetic properties and the underlying
Comparison of properties of Nd-Fe-B and Sm-Co permanent magnets
International Nuclear Information System (INIS)
Ervens, W.
1985-01-01
In this paper permanent magnet materials on the basis of RECo and NdFeB are compared in terms of manufacturing processes, magnetic values at ambient and elevated temperatures, maximum operating temperatures and magnetization behaviour. At the present stage of development NdFeB-magnets are superior to the high coercivity RECo-magnets in their B/sub r/ - and (BH)/sub ma//sup -/ values at room temperature but are inferior to them at temperatures higher than 120 0 C
Nd-Fe-B sintered magnets fabrication by using atomized powders
International Nuclear Information System (INIS)
Goto, R; Sugimoto, S; Matsuura, M; Tezuka, N; Une, Y; Sagawa, M
2011-01-01
Nd-Fe-B sintered magnets are required to achieve high coercivity for improvement of their thermal stability. Dy is added to increase coercivity, however, this element decrease magnetization and energy products. Therefore, Dy-lean Nd-Fe-B sintered magnets with high coercivity are strongly demanded. To increase coercivity, it is necessary that microstructure of sintered magnets is consisted of both fine main phase particles and homogeneously distributed Nd-rich phases around the main phase. To meet those requirements, Nd-Fe-B atomized powders were applied to the fabrication process of sintered magnets. Comparing with the case of using strip casting (SC) alloys, jet-milled powders from atomized powders show homogeneous distribution of Nd-rich phase. After optimized thermal treatment, coercivities of sintered magnets from atomized powders and SC alloys reach 1050 kA·m-1 and 1220 kA·m-1, respectively. This difference in coercivity was due to initial oxygen concentration of starting materials. Consequently, Nd-rich phases became oxides with high melting points, and did not melt and spread during sintering and annealing.
Lakshmanan, Saravanan; Rao, Subha Krishna; Muthuvel, Manivel Raja; Chandrasekaran, Gopalakrishnan; Therese, Helen Annal
2017-08-01
Magnetization of Ta/CoFeB/Ta trilayer films with thick layer of CoFeB deposited under different substrate temperatures (Ts) via ultra-high vacuum DC sputtering technique has been measured with the applied magnetic field parallel and perpendicular to the plane of the film respectively to study the perpendicular coercive forces of the film. The samples were further analyzed for its structural, topological, morphological, and electrical transport properties. The core chemical states for the elements present in the CoFeB thin film were analyzed by XPS studies. Magnetization studies reveal the existence of perpendicular coercive forces in CoFeB films deposited only at certain temperatures such as RT, 450 °C, 475 °C and 500 °C. CoFeB film deposited at 475 °C exhibited a maximum coercivity of 315 Oe and a very low saturation magnetization (Ms) of 169 emu/cc in perpendicular direction. This pronounced effect in perpendicular coercive forces observed for CoFeB475 could be attributed to the effect of temperature in enhancing the crystallization of the film at the Ta/CoFeB interfaces. However at temperatures higher than 475 °C the destruction of the Ta/CoFeB interface due to intermixing of Ta and CoFeB results in the disappearance of magnetic anisotropy.
The corrosion behaviour and structure of amorphous and thermally treated Fe-B-Si alloys
International Nuclear Information System (INIS)
Raicheff, R.; Zaprianova, V.; Petrova, E.
2003-01-01
The corrosion behaviour of magnetic amorphous alloys Fe 78 B 13 Si 9 , Fe 81 B 13 Si 4 C 2 and Fe 67 Co 18 Bi 4 S 1 obtained by rapid quenching from the melts are investigated in a model corrosive environment of 1N H 2 SO 4 . The structure of the alloys, is, characterized by DTA, SEM, TEM, X-ray and electron diffraction techniques. The dissolution kinetics of the,alloys is studied using gravimetric and electrochemical polarization measurements. It is established that the corrosion rate of the amorphous Fe 67 Co 18 Bt 4 S 1 alloy is up to 50 times lower than that of Fe 78 Bi 3 Si 9 alloy and the addition of cobalt leads to a considerable reduction of the rates of both partial corrosion reactions, while the addition of carbon results only in a moderate decrease (2-3 times) of the corrosion rate. It is also shown that the crystallization of the amorphous Fe 78 B 13 Si 9 alloy (at 700 o C for 3 h) leads to formation of multiphase structure consisting of crystalline phases α-Fe and Fe 3 (B,Si). After crystallization an increase of the rate of both hydrogen evolution and anodic dissolution reactions is observed which results in a considerable (an order of magnitude) increase of the corrosion rate of the alloy. (Original)
Thermoelectric power measurements in liquid quenched amorphous alloys for FeZr and (FeCo)B
International Nuclear Information System (INIS)
Raza, S.M.; Naqvi, S.M.M.R.; Rizvi, S.; Hussain, A.; Rahman, F.
1999-01-01
Thermoelectric power (TEP) measurements have been carried out on six samples of LQA alloys from two different series, namely FeZr and Fe(Co)B, at relatively low temperatures. Thermoelectric power shows an overall Gaussian trend. The scattering centers are the major contributors to the residual TEP. Ziman theoretical model was used to estimate TEP. It was found that Ziman theory fails to account for quantitative TEP measurements at relatively low temperatures (77K< T<300K). (author)
Directory of Open Access Journals (Sweden)
José Roberto Franco Reis
2000-06-01
Full Text Available Este artigo propõe-se a discutir as propostas de intervenção na problemática infantil apresentadas pela Liga Brasileira de Higiene Mental (LBHM, instituição criada no começo da década de 1920 que reunia a elite da psiquiatria brasileira, mas também alguns médicos e intelectuais em geral. Fundada num momento de afirmação, no campo psiquiátrico, da perspectiva preventiva, a LBHM vai incorporar ao seu arsenal teórico os temas básicos da higiene mental e da eugenia, tendo em vista o seu objetivo maior de colaborar no "saneamento racial" brasileiro. Assim, é a partir desse objetivo e vendo na criança um "pré-cidadão", "peça fundamental do homem do futuro", que os psiquiatras da liga incluem a questão infantil nos seus projetos, passando a considerar imperiosa a necessidade de cuidados desde a mais tenra idade.Created in the early 1920s, at a moment when the country’s psychiatric field was embracing the preventive outlook, the Liga Brasileira de Higiene Mental included within its members the elite of Brazilian psychiatry, along with a number of physicians and intellectuals. The article discusses the institution’s proposals for intervention among children. The league ended up incorporating into its theoretical arsenal the basic themes of mental hygiene and eugenics as part of its general goal of collaborating in Brazil’s process of "racial sanitation". With this objective in mind, and viewing the child as a "pre-citizen" who is a "fundamental part within the man of the future", league members included the children’s issue in their projects and saw an imperative need for mental health care from early ages on.
Trapped magnetic field in a (NdFeB)–(MgB{sub 2}) pair-type bulk magnet
Energy Technology Data Exchange (ETDEWEB)
Aldica, Gheorghe [National Institute of Materials Physics, Atomistilor 105bis, 077125 Magurele, Ilfov (Romania); Burdusel, Mihail [National Institute of Materials Physics, Atomistilor 105bis, 077125 Magurele, Ilfov (Romania); Faculty of Materials Science and Engineering, ‘‘Politehnica’’ University of Bucharest, Splaiul Independentei 316, 060042 Bucharest (Romania); Badica, Petre, E-mail: badica2003@yahoo.com [National Institute of Materials Physics, Atomistilor 105bis, 077125 Magurele, Ilfov (Romania)
2014-10-15
Highlights: • Dense MgB{sub 2} discs were obtained by ex-situ Spark Plasma Sintering. • A NdFeB–MgB{sub 2} pair-type bulk magnet was tested for different working conditions. • The polarity of the NdFeB permanent magnet influences macro flux jumps of MgB{sub 2}. • Trapped field of the pair was 2.45 T (20 K) and 3.3 T (12 K). - Abstract: Superconducting bulk discs, S, of 20 mm in diameter and 3.5 or 3.3 mm thickness of MgB{sub 2} (pristine or added with cubic BN, respectively) with density above 97% were prepared by Spark Plasma Sintering. Discs were combined in a pair-type sandwich-like arrangement with a permanent NdFeB axially magnetised magnet, PM (∼0.5 T). Measurement of the trapped field, B{sub tr}, with temperature, time, and the reduction rate of the applied magnetic field was performed using a Hall sensor positioned at the centre between the superconductor and the permanent magnet. It is shown that the permanent magnet with certain polarity favors higher trapped field of the superconductor owing to suppression of flux jumps specific for high density MgB{sub 2} samples. The B{sub tr} of the PM–S pair was 2.45 T (20 K) and 3.3 T (12 K)
Improved magnetic properties and fracture strength of NdFeB by dehydrogenation
Energy Technology Data Exchange (ETDEWEB)
Yan, M. [State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027 (China)]. E-mail: mse_yanmi@dial.zju.edu.cn; Yu, L.Q. [State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Wu, J.M. [State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Cui, X.G. [State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027 (China)
2006-11-15
Effects of the dehydrogenation of the hydrogen decrepitated (HD) powders on the magnetic properties and the fracture strength of sintered NdFeB magnets were studied. It was found that the lattice parameters and the crystal phase of NdFeB changed significantly with the various hydrogen contents of the resultant HD powders due to the different degrees of dehydrogenation. The magnetic properties and fracture strength increased with decreasing hydrogen content, reaching the maximum increases of 200% for both intrinsic coercivity and bending strength, which can be ascribed to the improved microstructure of the sintered NdFeB magnets. The hydrogen remaining in the HD powders diffused out and affected drastically the grain and grain boundaries by the hydrogen out-take channel during the subsequent sintering process.
Improved magnetic properties and fracture strength of NdFeB by dehydrogenation
International Nuclear Information System (INIS)
Yan, M.; Yu, L.Q.; Wu, J.M.; Cui, X.G.
2006-01-01
Effects of the dehydrogenation of the hydrogen decrepitated (HD) powders on the magnetic properties and the fracture strength of sintered NdFeB magnets were studied. It was found that the lattice parameters and the crystal phase of NdFeB changed significantly with the various hydrogen contents of the resultant HD powders due to the different degrees of dehydrogenation. The magnetic properties and fracture strength increased with decreasing hydrogen content, reaching the maximum increases of 200% for both intrinsic coercivity and bending strength, which can be ascribed to the improved microstructure of the sintered NdFeB magnets. The hydrogen remaining in the HD powders diffused out and affected drastically the grain and grain boundaries by the hydrogen out-take channel during the subsequent sintering process
Analysis of physical and magnetic properties of composite NdFeB bind with polyvinyl alcohol
Ramlan; Sardjono, P.; Muljadi; Setiabudidaya, D.; Gulo, F.
2018-03-01
The composite magnet NdFeB has been made using magnetic powder MQP-B and polyvinyl alcohol (PVA) as the binder. The mixing compositions of raw materials used are: 95 wt% NdFeB - 5 wt% PVA, 92.5 wt% NdFeB - 7.5 wt% PVA, 90 wt.% NdFeB - 10 wt% PVA, and 87.5 wt% NdFeB - 12.5 wt% PVA. Both raw materials are weighed according to the composition, and then mixed until homogeneous. Furthermore, pellet forming was made using dry pressing at 50 kgf/cm2 pressures and continued with drying at 100 °C and 10 mmbar for 4 hours. The characterization includes bulk density, hardness, compressive strength measurements, and magnetic properties testing. The characterization results show that the optimal composition of binder PVA is achieved at 5–7.5 wt% NdFeB composite magnet with following properties: bulk density = 5.21–5.25 g/cm3, hardness = 302.17 - 304.32 Hv, compressive strength = 25.17–3.17 kgf/cm2, magnetic flux = 1150-1170 Gauss, remanence = 70.90–74.97 emu/g or 4.7–5.0 kGauss, coercivity = 8.68–8.76 kOe, and energy product = 2.89–3.04 MgOe.
Optical properties of LiGaS2: an ab initio study and spectroscopic ellipsometry measurement
International Nuclear Information System (INIS)
Atuchin, V V; Lin, Z S; Isaenko, L I; Lobanov, S I; Kesler, V G; Kruchinin, V N
2009-01-01
Electronic and optical properties of lithium thiogallate crystal, LiGaS 2 , have been investigated by both experimental and theoretical methods. The plane-wave pseudopotential method based on DFT theory has been used for band structure calculations. The electronic parameters of Ga 3d orbitals have been corrected by the DFT+U methods to be consistent with those measured with x-ray photoemission spectroscopy. Evolution of optical constants of LiGaS 2 over a wide spectral range was determined by developed first-principles theory and dispersion curves were compared with optical parameters defined by spectroscopic ellipsometry in the photon energy range 1.2-5.0 eV. Good agreement has been achieved between theoretical and experimental results.
Designing a Virtual laboratory for Simulating to Production of Nanocomposite NdFeB Magnets
Directory of Open Access Journals (Sweden)
Musa Faruk Çakir
2014-02-01
Full Text Available The talent figure for a permanent magnet is the multiplication of the maximum energy (BHmax. Less volume magnet is required for the production of magnet flux density if the BHmax value is higher. Mathematical functions are obtained from the data related to resiudal flux density, magnetic coercitivy, permanent magnet flux product capability, Curie temperature and density which were obtained as a result of the studies on different NdFeB alloys in the laboratory. Besides this, mathematical functions of NdFeB hard magnet’s resiudal flux density are obtained by adding elements. In this study, a virtual laboratory for producing nanocompositedNdFeB magnet has been designed. The virtual laboratory software has been used to simulate NdFeB hard magnets for industrial utilities.
Silva, Éverton F.; Medeiros, Marco A.; McBride, Alan J. A.; Matsunaga, Jim; Esteves, Gabriela S.; Ramos, João G. R.; Santos, Cleiton S.; Croda, Júlio; Homma, Akira; Dellagostin, Odir A.; Haake, David A.; Reis, Mitermayer G.; Ko, Albert I.
2007-01-01
Subunit vaccines are a potential intervention strategy against leptospirosis, which is a major public health problem in developing countries and a veterinary disease in livestock and companion animals worldwide. Leptospiral immunoglobulin-like (Lig) proteins are a family of surface-exposed determinants that have Ig-like repeat domains found in virulence factors such as intimin and invasin. We expressed fragments of the repeat domain regions of LigA and LigB from Leptospira interrogans serovar...
LigaSure small jaws versus cold knife dissection in superficial parotidectomy
DEFF Research Database (Denmark)
Hahn, Christoffer Holst; Sørensen, Christian Hjort
2013-01-01
parotidectomy, and 19 patients had cold knife parotidectomy. Operative time, blood loss, facial palsy and other complications were assessed. The use of LigaSure was associated with a significant reduction in mean operative time (128 min vs. 155, p = 0.04) and intraoperative blood loss (40 mL vs. 115 mL, p ...
Highly textured Nd-Fe-B films grown on amorphous substrates
International Nuclear Information System (INIS)
Hannemann, Ullrich; Melcher, Steffen; Faehler, Sebastian
2004-01-01
Thin films with an almost perfect alignment of Nd 2 Fe 14 B grains with the c-axis (easy magnetisation direction) perpendicular to the film plane were achieved on amorphous SiN substrates using pulsed laser deposition. The texture arises due to epitaxial growth on a Ta(1 1 0) buffer deposited prior to the Nd-Fe-B film. Out-of-plane coercivity of 1.3 T and remanence to saturation magnetisation ratio around 0.95 are obtained for Nd-rich films. An analysis of the coercivity mechanism shows that the switching mechanism is nucleation dominated, independent of the Nd content
Highly textured Nd-Fe-B films grown on amorphous substrates
Energy Technology Data Exchange (ETDEWEB)
Hannemann, Ullrich E-mail: u.hannemann@ifw-dresden.de; Melcher, Steffen; Faehler, Sebastian
2004-05-01
Thin films with an almost perfect alignment of Nd{sub 2}Fe{sub 14}B grains with the c-axis (easy magnetisation direction) perpendicular to the film plane were achieved on amorphous SiN substrates using pulsed laser deposition. The texture arises due to epitaxial growth on a Ta(1 1 0) buffer deposited prior to the Nd-Fe-B film. Out-of-plane coercivity of 1.3 T and remanence to saturation magnetisation ratio around 0.95 are obtained for Nd-rich films. An analysis of the coercivity mechanism shows that the switching mechanism is nucleation dominated, independent of the Nd content.
Oxygen Non-Stoichiometry and Electrical Conductivity of La0.2Sr0.8Fe0.8B0.2O3 − δ, B = Fe, Ti, Ta
DEFF Research Database (Denmark)
Lohne, Ørjan Fossmark; Phung, Tan Nhut; Grande, Tor
2014-01-01
The oxygen non-stoichiometry was determined by coulometric titration for the perovskite oxides La0.2Sr0.8FeO3 − δ and La0.2Sr0.8Fe0.8B0.2O3 − δ (B = Ti4+ and Ta5+) in the temperature range 600 °C ⩽ T ⩽ 900 °C and the oxygen partial pressure range: 1⋅10-15≤po2≤0.209 atm. The non-stoichiometry (δ...... for the substituted materials. The electrical conductivity was measured at T = 900 °C in the oxygen partial pressure range: 1⋅10-17≤po2≤0.209 atm. The electrical conductivity and charge carrier mobility decrease upon 20% substitution of Fe roughly by a factor of 2, but do not show a significant dependence......) is observed to decrease with B-site substitution of Fe. The data can be well fitted with simple defect chemistry models. At low oxygen non-stoichiometry all compositions show a deviation from a localized electrons defect model. The standard and partial molar thermodynamic quantities were obtained...
Structural, magnetic and optical properties of Y bFe2O4 films deposited by spin coating
Directory of Open Access Journals (Sweden)
Tatsuo Fujii
2016-08-01
Full Text Available Rare-earth iron oxides (RFe2O4 have attracting attention as new electronic device materials because of their numerous functionalities, such as electronic ferroelectricity, ferrimagnetism, and high infrared absorption. In this paper, nearly monophasic Y bFe2O4 films were prepared on α-Al2O3(001 substrates by the spin coating method using an aqueous-based Y bFe2O4 solution. The solution was composed of a stoichiometric ratio of Y b(CH3COO3 and Fe(NO33 with excess chelating agents. After heat treatment above 800 °C, well-crystallized and highly (001-oriented Y bFe2O4 started to epitaxially form on the substrate under controlled oxygen partial pressure with H2/CO2 gas mixtures. X-ray pole figure analysis confirmed the following epitaxial relationship: Y bFe2O4[100](001//α-Al2O3[100](001. Moreover formation of an Fe3O4 interracial layer between Y bFe2O4 and α-Al2O3 was detected by high-resolution transmission electron microscopy. Presence of the Fe3O4 interracial layer seemed to release the lattice misfit with the substrate. The Fe2+/Fe3+ ratio in the obtained Y bFe2O4 films was nearly stoichiometric and the indirect bandgap assigned to Fe2+ → Fe3+ charge transfer excitation was found to be ∼0.4 eV by optical spectroscopy. A clear magnetic transition from the paramagnetic state to the ferrimagnetic state occurred at ∼230 K.
Energy Technology Data Exchange (ETDEWEB)
Li, Xu-Jing; Jiang, Shao-Long; Zhang, Jing-Yan; Liu, Qian-Qian; Liu, Yi-Wei; Zhao, Jian-Cheng [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Wu, Zheng-Long [Analytical and Testing Center, Beijing Normal University, Beijing 100875 (China); Feng, Chun, E-mail: fengchun@ustb.edu.cn [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Li, Ming-Hua [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Yu, Guang-Hua, E-mail: ghyu@mater.ustb.edu.cn [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China)
2016-03-01
Graphical abstract: To reveal the underlying mechanism of Mg influence on the enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers, the X-ray photoelectron spectroscopy analysis have been performed. It is found that a certain amount of Mg interlayer at the CoFeB/MgO interface could prevent the Ta oxidation to some extent due to the oxygen deficit MgO{sub x} (x < 1), and consequently lower the diffusion motivation of Ta from the bottom layer to the CoFeB/MgO interfaces to some extent during the annealing process. The prevention of Ta diffusion realizes the effective hybridization of Fe and O at the CoFeB/MgO interface and maintains interfacial magnetic anisotropy (K{sub CoFeB/MgO}). As a result, the perpendicular magnetic anisotropy at high annealing temperatures was maintained. - Highlights: • High annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers was realized. • X-ray photoelectron spectroscopy analysis has been performed to explore the reasons. • The prevention of Ta diffusion was realized by introducing Mg at the CoFeB/MgO interface. - Abstracts: To reveal the underlying mechanism of Mg influence on the enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers, the X-ray photoelectron spectroscopy analysis has been performed. It is found that a certain amount of Mg interlayer at the CoFeB/MgO interface could prevent the Ta oxidation, and consequently lower the diffusion motivation of Ta from the bottom layer to the CoFeB/MgO interfaces to some extent in the annealing process. The prevention of Ta diffusion realizes the effective hybridization of Fe and O at the CoFeB/MgO interface and maintains interfacial magnetic anisotropy (KCoFeB/MgO). As a result, the perpendicular magnetic anisotropy at high annealing temperatures is maintained.
International Nuclear Information System (INIS)
Li Shandong; Wang Dawei; Fang Jianglin; Duh, J.-G.; Wang Yinying; Wu Yizhi; Huang Junheng; Zheng Hongjun
2008-01-01
NdFeB films with Nd compositions varied from 13.34 to 24.30 at% were deposited by DC gradient sputtering using targets Nd 12.5 Fe 71.5 B 16 and Nd. The hard magnetic properties, grain growth direction and magnetic domain structures were dramatically influenced by Nd composition. The samples with intermediate Nd concentrations exhibited optimal magnetic properties and microstructures, such as large squareness ratio over 0.9, large energy product up to 174 kJ/m 3 , and vertical domain structure. However, the samples with higher and lower Nd compositions showed almost isotropic loops. (0 0 l) as main X-ray diffraction peaks in the optimal Nd composition region indicated most of Nd 2 Fe 14 B grains with c-axis perpendicular to the film plane, while NdFeB grains in other region are almost random growth. The good magnetic properties can be attributed to the vertical growth of Nd 2 Fe 14 B grains
Energy Technology Data Exchange (ETDEWEB)
Li Shandong [Department of Physics, Fujian Normal University, Fuzhou 350007 (China)], E-mail: dylsd007@yahoo.com.cn; Wang Dawei [Department of Physics, Fujian Normal University, Fuzhou 350007 (China); Fang Jianglin [Center for Materials Analysis, Nanjing University, Nanjing 210093 (China); Duh, J.-G. [Department of Materials Science and Engineering, National TsingHua Universtiy, Hsinchu, Taiwan (China); Wang Yinying; Wu Yizhi; Huang Junheng; Zheng Hongjun [Department of Physics, Fujian Normal University, Fuzhou 350007 (China)
2008-08-15
NdFeB films with Nd compositions varied from 13.34 to 24.30 at% were deposited by DC gradient sputtering using targets Nd{sub 12.5}Fe{sub 71.5}B{sub 16} and Nd. The hard magnetic properties, grain growth direction and magnetic domain structures were dramatically influenced by Nd composition. The samples with intermediate Nd concentrations exhibited optimal magnetic properties and microstructures, such as large squareness ratio over 0.9, large energy product up to 174 kJ/m{sup 3}, and vertical domain structure. However, the samples with higher and lower Nd compositions showed almost isotropic loops. (0 0 l) as main X-ray diffraction peaks in the optimal Nd composition region indicated most of Nd{sub 2}Fe{sub 14}B grains with c-axis perpendicular to the film plane, while NdFeB grains in other region are almost random growth. The good magnetic properties can be attributed to the vertical growth of Nd{sub 2}Fe{sub 14}B grains.
Local profile dependence of coercivity in (MM0.3Nd0.7)-Fe-B sintered magnets
Yu, Xiaoqiang; Zhu, Minggang; Liu, Weiqiang; Li, Wei; Sun, Yachao; Shi, Xiaoning; Yue, Ming
2018-03-01
Two magnets with the same nominal composition of (MM0.3Nd0.7)-Fe-B (Marked as A) and [(La0.27Ce0.53Pr0.03Nd0.17)0.3Nd0.7]-Fe-B (Marked as B) were prepared using traditional powder metallurgical process, respectively. In order to point out the difference between two magnets, the magnetic properties, microstructure and magnetic domain of both magnets were investigated. Both magnets have the same elements, but different raw materials of misch-metal (MM) and La/Ce/Pr/Nd pure metal, which induces different magnetic properties. The magnet A with Br of 13.1 kGs, Hcj of 7.6 kOe, (BH)max of 37.8 MGOe and magnet B with Br of 13.4 kGs, Hcj of 5.8 kOe, (BH)max of 34.5 MGOe are obtained. Although both magnets have the similar Br, magnet A has higher coercivity than that of magnet B. According to refined results of characteristic X-ray diffraction peaks, there is a hard magnetic main phase with higher magnetic anisotropy field (HA) in magnet A and opposite case happens on magnet B. SEM images demonstrate that magnet A has more continuous RE-rich phase and smaller grain size compared to that of magnet B, which contributes to enhancing the coercivity. In addition, two main phases of [Nd0.82(La, Ce)0.18]-Fe-B and [Nd0.75(La, Ce)0.25]-Fe-B were detected by the EDX calculation, and the two main phases in both magnets were observed by magnetic domains again. Compared to magnet B, 2:14:1 main phases in magnet A contain more [Nd0.82(La, Ce)0.18]-Fe-B main phases and less [Nd0.75(La, Ce)0.25]-Fe-B main phases, which also leads to higher coercivity due to the different HA among Nd2Fe14B, La2Fe14B and Ce2Fe14B phases. Therefore, it is concluded that MM substitution could exhibit better magnetic properties than (La0.27Ce0.53Pr0.03Nd0.17)-metal substitution. Furthermore, applications of MM are beneficial to fabricate (MM, Nd)-Fe-B permanent magnets with lower cost.
Directory of Open Access Journals (Sweden)
Udovsky A.
2016-01-01
Full Text Available A concept of partial magnetic moments (PMM of the iron atoms located in the first ч four coordination spheres (1÷4 CS for bcc lattice have been introduced based on analysis of results obtained by quantum-mechanical calculations (QMC for volume dependence of the average magnetic moment ferromagnetic (FM Fe. The values of these moments have been calculated for pure bcc Fe and bcc - Fe-Cr alloys. This concept has been used to formulate a three sub-lattice model for binary FM alloys of the Fe-M systems (M is an alloying paramagnetic element. Physical reason for sign change dependence of the short-range order and mixing enthalpy obtained by QMCs for Fe-(Cr, V bcc phases has been found. Using this model it has been predicted that static displacements of Fe - atoms in alloy matrix increase with increasing the of CS number and result in reducing of the area of coherent dissipation (ACD size with growth of the dimension factor (DF in the Fe-(Cr, V, Mo, W systems in agreement with the X-ray experiments. It has been shown theoretically that anisotropy of spin- density in bcc lattice Fe and DF in binary Fe - (Cr, V, Mo, W systems is main factor for origins of segregations on small angle boundaries of ACD and sub-grains boundaries To prevent the coagulation of both ACD and sub-grains, and to increase the strength of alloys, it is advisable to add oxide dispersion particles into ferrite steel taking into account their chemical compatibility and coherent interfacing with the crystalline lattice of a ferrite matrix. Application of phase diagrams for binary and ternary the Fe-(Y, Zr-O systems to verify chemical compatibility of oxide dispersion particles with ferrite matrix have been discussed
Hard magnetic properties and coercivity mechanism of melt-spun Misch Metal-Fe-B alloy
Energy Technology Data Exchange (ETDEWEB)
Quan, Ningtao; Luo, Yang, E-mail: eluoyang@foxmail.com; Yan, Wenlong; Yuan, Chao; Yu, Dunbo; Sun, Liang; Lu, Shuo; Li, Hongwei; Zhang, Hongbin
2017-09-01
Highlights: • Melt-spun MM{sub 13}Fe{sub 81}B{sub 6} alloy shows that the distributions of the La, Ce, Pr, Nd, Fe and B elements is uniformly distributed, and the grain size is in the range of 30–40 nm, it can be seen that Pr-rich and La-rich phases concentrated on grain boundaries, which resulted in the coercivity augment with the increase of MMFe{sub 2} content, and the grain size is around 40–50 nm in MM{sub 16}Fe{sub 78}B{sub 6}. • There is a significant formation of MMFe{sub 2} with abundant Pr and La, and a small amount of Ce and Nd enriched at the interfacial region in MM{sub 16}Fe{sub 78}B{sub 6}, thus an inhomogeneous region was formed. It is considered that the inhomogeneous region is effective in increasing the coercivity. • The optimum-quenched MM{sub 13}Fe{sub 81}B{sub 6} alloy have been shown to exhibit a coercive force of 6.9 kOe and an energy product of 8.5 MGOe, which is superior to anisotropic ferrite magnets of 4.5 MGOe. - Abstract: Magnetic and structural properties of Misch Metal (MM)-Fe-B alloys, were examined in the melt-spun ribbons. Melt-spun MM-Fe-B samples were prepared at the surface velocities of 18–30 m/s. Crystalline structure and their room-temperature magnetization characteristics were analyzed, and the optimum surface velocity of 20 m/s and nominal composition of MM{sub 13}Fe{sub 81}B{sub 6} were obtained. Microstructural analyses indicate that the grain size is approximately 30–50 nm in the alloys with the optimum characteristics. In the MM{sub 16}Fe{sub 78}B{sub 6} alloys, Pr-rich and La-rich phases concentrated on grain boundaries, which resulted in the coercivity augment with the increase of MMFe{sub 2} content. Dependence of coercivity on applied magnetic field suggested that the mechanism of coercivity in moderate MM-content samples was inhomogeneous domain wall pinning type. The melt-spun ribbons in the optimum condition exhibit a coercive force of 6.9 kOe and an energy product of 8.5 MGOe, which can be used as
Wang, Cuiling; Zhang, Shouheng; Qiao, Shizhu; Du, Honglei; Liu, Xiaomin; Sun, Ruicong; Chu, Xian-Ming; Miao, Guo-Xing; Dai, Youyong; Kang, Shishou; Yan, Shishen; Li, Shandong
2018-05-01
Dual-mode ferromagnetic resonance is observed in FeCoB/Ru/FeCoB trilayer synthetic antiferromagnets with uniaxial in-plane magnetic anisotropy. The optical mode is present in the (0-108 Oe) magnetic field range, where the top and bottom layer magnetizations are aligned in opposite directions. The strong acoustic mode appears, when the magnetic field exceeds the 300 Oe value, which corresponds to the flop transition in the trilayer. Magnetic field and angular dependences of resonant frequencies are studied for both optical (low-field) and acoustic (high field) modes. The low-field mode is found to be anisotropic but insensitive to the magnetic field value. In contrast, the high field mode is quasi-isotropic, but its resonant frequency is tunable by the value of the magnetic field. The coexistence of two modes of ferromagnetic resonance as well as switching between them with the increase in the magnetic field originates from the difference in the sign of interlayer coupling energy at the parallel and antiparallel configurations of the synthetic antiferromagnet. The dual-mode resonance in the studied trilayer structures provides greater flexibility in the design and functionalization of micro-inductors in monolithic microwave integrated circuits.
Energy Technology Data Exchange (ETDEWEB)
Kayama, Koichiro; Hashimoto, Yasuhiko; Suzuki, Kenji; Matsuo, Hideki (Himeji Inst. of Tech., Hyogo (Japan) Fukushin Electric Co., Ltd., Hyogo (Japan))
1989-12-25
NiW {sub 2} B {sub 2} (M phase), existing in trinary Ni-W-B system, was measured in standard Gibbs free energy (GF) of formation in the temperature range from 1273K to 1423K by an electromotive force method (EMF) with use of solid oxide electrolyte. First, oxide phase in equilibrium with three-phase M-W-Ni solid solution region was confirmed to be B {sub 2} O {sub 3}. Binary Ni-W system solid solution in equilibrium with M phase and W phase is constant in composition with Ni-16.4mo1%W in the above temperature range. WO {sub 2} and WO {sub 2.72} were actually measured in GF. As Ni-W solid solution is in equilibrium with WO {sub 2} and WO {sub 2.72}, binary Ni-W system was measured in activity by the EMF, and Ni-16.4mo1%W solid solution was calculated in GF of mixing by use of the above measured GF of WO {sub 2} and WO {sub 2.72}. Finally with use of sample in M-W-Ni solid solution region, M phase was calculated in GF by the EMF. The result of those calculations were expressed with experimental formulas. 19 refs., 10 figs., 3 tabs.
Metallic glasses of the type Fe80B17X3
International Nuclear Information System (INIS)
Riedel, M.; Gnaser, H.; Ruedenauer, F.G.
1981-08-01
Absolute and relative practical sensitivities for Osub2sup+ - bombardement of 14 elements, present as a 3% admixture in a Fe80B17X3 metallic glass matrix, were determined by SIMS. The variation of sensitivity data between elements is similar to that found for pure element samples. The 3% admixture causes a small but statistically significant matrix effect on the matrix elements Fe and B. Comparison with yield data of the same minor impurity elements in other matrices (stainless steel, silicon) shows, that sensitivities in different matrices are within 30% for most elements, indicating the possibility of transferring relative sensitivity factor data determined on metallic glasses to other Fe-based alloys and thereby obtaining a semi- quantitative analysis. (author)
Multi-phase EBSD mapping and local texture analysis in NdFeB sintered magnets
Energy Technology Data Exchange (ETDEWEB)
Woodcock, T.G., E-mail: t.woodcock@ifw-dresden.de [IFW Dresden, Institute for Metallic Materials, PO Box 270116, 01171 Dresden (Germany); Gutfleisch, O. [IFW Dresden, Institute for Metallic Materials, PO Box 270116, 01171 Dresden (Germany)
2011-02-15
A combination of electron backscatter diffraction and energy-dispersive X-ray spectroscopy has been used to identify the crystal structure and composition of all the phases present in commercially available NdFeB sintered magnets and to map their spatial distribution. The Nd{sub 2}Fe{sub 14}B and NdO grains were shown to have low defect densities. The fcc Nd-rich and Nd{sub 2}O{sub 3} grains had intra-grain misorientation angles of up to 14{sup o}, which was shown to be due to defects. Large numbers ({approx}100) of data points for each phase were used to study texture in the NdO, Nd{sub 2}O{sub 3} and Nd{sub 2}Fe{sub 14}B phases. The Nd{sub 2}Fe{sub 14}B grains exhibited a <0 0 1> fibre texture. The Nd oxide phases showed no strong texture, which implied that no strongly preferred orientation relationships between those phases and Nd{sub 2}Fe{sub 14}B exist. The result was shown to be valid for optimally annealed samples exhibiting high coercivity and as-sintered samples exhibiting low coercivity.
Preparation and magnetic properties of anisotropic bulk MnBi/NdFeB hybrid magnets
Ma, Y. L.; Liu, X. B.; Nguyen, V. V.; Poudyal, N.; Yue, M.; Liu, J. P.
2016-08-01
Anisotropic hybrid bulk magnets of MnBi/NdFeB with different composition ratio have been prepared with starting MnBi and Nd2Fe14B powders as well as epoxy resin as a binder in case it is needed to form bulk samples. It has been found that the ratio between the two phases in content has a remarkable influence on the magnetic properties, the thermal stability and the density of the bulk magnets. With increasing MnBi content the binder addition can be reduced. When the MnBi content is larger than 30 wt%, no binder is needed. On the other hand, the coercivity and saturation magnetization were increased significantly with increasing NdFeB content. When the NdFeB content was increased from 0% to 50%, the maximum energy product was enhanced from 4.7 to 10.0 MGOe, respectively. The energy product then decreased gradually with the NdFeB content due to the reduced density of the hybrid magnet. The thermal stability measurements showed that the temperature coefficient of coercivity grew with the MnBi content and became positive with MnBi=80 wt%.
Structural Transformation in Fe73.5Nb3Cu1Si15.5B7 Amorphous Alloy Induced by Laser Heating
Nykyruy, Yu. S.; Mudry, S. I.; Kulyk, Yu. O.; Zhovneruk, S. V.
2018-03-01
The effect of continuous laser irradiation (λ = 1.06 μm) with laser power of 45 W on the structure of Fe73.5Nb3Cu1Si15.5B7 amorphous alloy has been studied using X-ray diffraction and SEM methods. The sample of the ribbon has been placed at a distance from the focal plane of the lens, so a laser beam has been defocused and the diameter of laser spot on the ribbon surface has been about 10 mm. An exposure time τ varied within interval 0.25-0.70 s. Under such conditions structural transformation processes, which depend on the exposure time, have occurred in an irradiated zone. Crystallization process has started at τ = 0.35 s with the formation of α-Fe(Si) nanocrystalline phase, while complete crystallization has occurred at τ = 0.55 s with formation of two nanocrystalline phases: α-Fe(Si) and a hexagonal H-phase.
Energy Technology Data Exchange (ETDEWEB)
Pirro, P., E-mail: ppirro@physik.uni-kl.de [Institut Jean Lamour, Université de Lorraine, UMR 7198 CNRS, 54506 Vandoeuvre-lés-Nancy (France); Hamadeh, A.; Lavanant-Jambert, M. [Institut Jean Lamour, Université de Lorraine, UMR 7198 CNRS, 54506 Vandoeuvre-lés-Nancy (France); Meyer, T. [Fachbereich Physik and Landesforschungszentrum OPTIMAS, Technische Universität Kaiserslautern, 67663 Kaiserslautern (Germany); Tao, B.; Rosario, E.; Lu, Y.; Hehn, M.; Mangin, S.; Petit Watelot, S. [Institut Jean Lamour, Université de Lorraine, UMR 7198 CNRS, 54506 Vandoeuvre-lés-Nancy (France)
2017-06-15
Highlights: • MgO/CoFeB/Ta/CoFeB/MgO multilayers as synthetic ferrimagnets. • Comprehensive characterization by measurement of static and dynamic properties. • Different pinning for domain walls with different alignment of the individual layers. - Abstract: A study of the multilayer system MgO/CoFeB(1.1 nm)/Ta(t)/CoFeB(0.8 nm)/MgO is presented, where the two CoFeB layers are separated by a Ta interlayer of varying thickness t. The magnetization properties deduced from complementary techniques such as superconducting quantum interference magnetometry, ferromagnetic resonance frequency measurements and Brillouin light scattering spectroscopy can be tuned by changing the Ta thickness between t = 0.25 nm, 0.5 nm and 0.75 nm. For t = 0.5 nm, a ferromagnetic coupling is observed, whereas for t = 0.75 nm, the antiferromagnetic coupling needed to construct a synthetic ferrimagnet is realized. In the latter case, the shape of magnetic domain walls between two ferrimagnetic alignments or between a ferro- and a ferrimagnetic alignment is very different. This behavior can be interpreted as a result of the change in dipolar as well as interlayer exchange energy and domain wall pinning, which is an important conclusion for the realization of data storage devices based on synthetic ferri- and antiferromagnets.
International Nuclear Information System (INIS)
Il'inskij, A.G.; Brovko, A.P.; Zelinskaya, G.M.; Kosenko, N.S.; Khristenko, T.M.; Kobzenko, G.F.; Shkola, A.A.
1988-01-01
The structure of amorphous and amorphous-crystaliline Fe 40 Ni 40 B 20 and Co 70 Fe 5 Si-1 5 B 10 alloys, exposed to hydridation at different temperatures, is studied by X-ray diffraction technique. The presence of crystalline constituent in amorphous bands was determined on DRON-3 device and by method of small-angle scattering. The experimental data obtained verify, that hydridation does not only prevent the formation of crystalline phases at annealing, but leads, as well, to disappearance of band crystalline constituent in case of its presence
Preparation and properties of [(NdFeB)x/(Nb)z]n multi-layer films
International Nuclear Information System (INIS)
Tsai, J.-L.; Chin, T.-S.; Yao, Y.-D.; Melsheimer, A.; Fisher, S.; Drogen, T.; Kelsch, M.; Kronmueller, H.
2003-01-01
Multi-layer [(NdFeB) x /(Nb) z ] n films with 200 nm≥x≥10 nm, 10 nm≥z≥0, 40≥n≥2, prepared by ion beam sputtering and subsequent annealing, show significantly enhanced coercivity due to the reduced grain size that enhances the anisotropy of individual grains. After annealing at 630 deg. C, some Nd 2 Fe 14 B grains were enriched with Nb and isolated as the thickness of the Nb spacer layer increases. For multi-layer (NdFeB x /Nb z ) n films with 100 nm ≥x≥25 nm, 5 nm≥z≥2 nm, their coercivity and remanence ratio are better than that of a single NdFeB film. Up to 17.8 kOe room temperature coercivity has been obtained for a sample with x=25 nm, z=5 nm and n=16
Magnetic properties of (misch metal, Nd-Fe-B melt-spun magnets
Directory of Open Access Journals (Sweden)
R. Li
2017-05-01
Full Text Available The effect of replacing Nd with misch metal (MM on magnetic properties and thermal stability has been investigated on melt-spun (Nd1-xMMx13.5Fe79.5B7 ribbons by varying x from 0 to 1. All of the alloys studied crystallize in the tetragonal 2:14:1 structure with single hard magnetic phase. Curie temperature (Tc, coercivity (Hcj, remanence magnetization (Br and maximum energy product ((BHmax all decrease with MM content. The melt-spun MM13.5Fe79.5B ribbons with high ratio of La and Ce exhibit high magnetic properties of Hcj = 8.2 kOe and (BHmax= 10.3 MGOe at room temperature. MM substitution also significantly strengthens the temperature stability of coercivity. The coercivities of the samples with x = 0.2 and even 0.4 exhibit large values close to that of Nd13.5Fe79.5B7 ribbons above 400 K.
Energy Technology Data Exchange (ETDEWEB)
Xiaoya, Liu; Yuping, Li [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Lianxi, Hu, E-mail: hulx@hit.edu.cn [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)
2013-03-15
The process of mechanically activated disproportionation and desorption-recombination in-situ sintering was proposed to synthesize highly densified nanocrystalline NdFeB magnet, and its validity was demonstrated by experimental investigation with the use of a Nd{sub 16}Fe{sub 76}B{sub 8} (atomic ratio) alloy. Firstly, the as-cast alloy was disproportionated by mechanical milling in hydrogen, with the starting micron-sized Nd{sub 2}Fe{sub 14}B phase decomposed into an intimate mixture of nano-structured NdH{sub 2.7}, Fe{sub 2}B and {alpha}-Fe phases. The as-disproportionated alloy powders were compacted by cold pressing and then subjected to desorption-recombination in-situ sintering. The microstructure of both the as-disproportionated and the subsequently sintered samples was characterized by X-ray diffraction and electron transmission microscopy, respectively. The magnetic properties of the sintered samples were measured by using vibrating sample magnetometer. The results showed that, by vacuum sintering, not only was the powder compact consolidated, but also the as-disproportionated microstucture transformed into nanocrystalline Nd{sub 2}Fe{sub 14}B phase via the well-known desorption-recombination reaction, thus giving rise to nanocrystalline NdFeB magnet. In the present study, the optimal sintering parameters were found to be 780 Degree-Sign C Multiplication-Sign 30 min. In this case, the coercivity, the remanence, and maximum energy product of the magnet sample achieved 0.8 T, 635.3 kA/m, and 106.3 kJ/m{sup 3}, respectively. - Highlights: Black-Right-Pointing-Pointer Nano-structured disproportionated NdFeB alloy powders by mechanical milling in hydrogen. Black-Right-Pointing-Pointer Highly densified green magnet compact by cold pressing of as-disproportionated NdFeB alloy powders. Black-Right-Pointing-Pointer Nanocrystalline NdFeB magnets by desorption-recombination in-situ sintering under vacuum. Black-Right-Pointing-Pointer Magnetic properties significantly
Obras de fábrica resistentes. Consideraciones generales de cálculo
Directory of Open Access Journals (Sweden)
Jenaro Garrido, José María
1986-10-01
Full Text Available This work studies de resisting capacity of the non reinforced masonry works to normal requirements from the knowledge of the nominal value to compressive resistance of its elements, or from the results from compression tests carried out on masses or on masonry samples. The obtained expressions for homogeneous sections are also valid for sections that, because of their cavities, they can be considered heterogeneous, allowing a determination of its resistant behaviour by means of the introduction of the conceipt of resistant homogeneous equivalent section. Finaly it includes a study on deforming and buckling of the masonry works to which diverse expressions gathered already in the Model Code CEB-FIP and in the Instruction in force EH'82 for Concrete Works are applied.El presente artículo recoge un estudio de la capacidad resistente de las obras de fábrica no armadas ante las solicitaciones normales, a partir del conocimiento del valor nominal de la resistencia a compresión de los elementos componentes o de los resultados de ensayos a compresión realizados sobre macizos o probetas de obra de fábrica. Las expresiones obtenidas para secciones homogéneas se extienden a secciones que por comprender cavidades hayan de considerarse heterogéneas, haciendo posible una determinación de su comportamiento resistente mediante la introducción del concepto de sección resistente homogénea equivalente. Finalmente se incluye un estudio sobre la deformabilidad y pandeo de las obras de fábrica a los que se aplican diversas expresiones ya recogidas en el Código Modelo CEB-FIP y en la vigente Instrucción EH-82 para obras de hormigón.
40 keV Shaped electron beam lithography for LIGA intermediate mask fabrication
Luttge, R.; Adam, D.; Burkhardt, F.; Hoke, F.; Schacke, H.; Schmidt, M.; Wolf, H.; Schmidt, A.
1999-01-01
High precision LIGA masks require a soft X-ray pattern transfer from intermediate masks by means of electron beam lithography. Such a process has been realized using an upgraded Leica ZBA 23 machine with an acceleration voltage of 40 kV. Three process variations of the developer system, so called GG
B ampersand W PWR advanced control system algorithm development
International Nuclear Information System (INIS)
Winks, R.W.; Wilson, T.L.; Amick, M.
1992-01-01
This paper discusses algorithm development of an Advanced Control System for the B ampersand W Pressurized Water Reactor (PWR) nuclear power plant. The paper summarizes the history of the project, describes the operation of the algorithm, and presents transient results from a simulation of the plant and control system. The history discusses the steps in the development process and the roles played by the utility owners, B ampersand W Nuclear Service Company (BWNS), Oak Ridge National Laboratory (ORNL), and the Foxboro Company. The algorithm description is a brief overview of the features of the control system. The transient results show that operation of the algorithm in a normal power maneuvering mode and in a moderately large upset following a feedwater pump trip
International Nuclear Information System (INIS)
Li, Xu-Jing; Jiang, Shao-Long; Zhang, Jing-Yan; Liu, Qian-Qian; Liu, Yi-Wei; Zhao, Jian-Cheng; Wu, Zheng-Long; Feng, Chun; Li, Ming-Hua; Yu, Guang-Hua
2016-01-01
Graphical abstract: To reveal the underlying mechanism of Mg influence on the enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers, the X-ray photoelectron spectroscopy analysis have been performed. It is found that a certain amount of Mg interlayer at the CoFeB/MgO interface could prevent the Ta oxidation to some extent due to the oxygen deficit MgO_x (x < 1), and consequently lower the diffusion motivation of Ta from the bottom layer to the CoFeB/MgO interfaces to some extent during the annealing process. The prevention of Ta diffusion realizes the effective hybridization of Fe and O at the CoFeB/MgO interface and maintains interfacial magnetic anisotropy (K_C_o_F_e_B_/_M_g_O). As a result, the perpendicular magnetic anisotropy at high annealing temperatures was maintained. - Highlights: • High annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers was realized. • X-ray photoelectron spectroscopy analysis has been performed to explore the reasons. • The prevention of Ta diffusion was realized by introducing Mg at the CoFeB/MgO interface. - Abstracts: To reveal the underlying mechanism of Mg influence on the enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers, the X-ray photoelectron spectroscopy analysis has been performed. It is found that a certain amount of Mg interlayer at the CoFeB/MgO interface could prevent the Ta oxidation, and consequently lower the diffusion motivation of Ta from the bottom layer to the CoFeB/MgO interfaces to some extent in the annealing process. The prevention of Ta diffusion realizes the effective hybridization of Fe and O at the CoFeB/MgO interface and maintains interfacial magnetic anisotropy (KCoFeB/MgO). As a result, the perpendicular magnetic anisotropy at high annealing temperatures is maintained
Crystallization of the amorphous Fe{sub 80}Zr{sub 12}B{sub 8} alloy under controlled heating
Energy Technology Data Exchange (ETDEWEB)
Huang, H. [School of Engineering (H6), University of Surrey, Guildford, Surrey GU2 7XH (United Kingdom); Shao, G. [Centre for Materials Research and Innovation, University of Bolton, Bolton BL3 5AB (United Kingdom)], E-mail: G.Shao@bolton.ac.uk; Tsakiropoulos, P. [Department of Engineering Materials, Sir Robert Hadfirld Building, University of Sheffield, Mappin Street, Sheffield S1 3JD (United Kingdom)
2008-07-14
The devitrification process of amorphous Fe{sub 80}Zr{sub 12}B{sub 8} alloy ribbons were studied under controlled thermal conditions. The major crystallization event during continuous heating with differential scanning calorimetory (DSC) is dictated by diffusion controlled growth and the associated atom mobility of the slow diffusing species Zr. The existence of prior nano-crystals formed by pre-annealing below the crystallization temperature had little effect on the major crystallization temperature. The crystallization sequence during heating was: amorphous {yields} amorphous + {alpha}-Fe + Fe{sub 3}Zr(B) {yields} amorphous + {alpha}-Fe + Fe{sub 3}Zr(B) + Fe{sub 2}Zr. Different from previous findings in alloys of lower Zr and B contents, the peak for the crystallization of the {alpha}-Fe phase alone is missing in the DSC traces of this alloy.
Energy Technology Data Exchange (ETDEWEB)
Li, Zhu-bai, E-mail: lzbgj@163.com [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); State Key Laboratory for Magnetism, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Wang, Li-chen [Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Material Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Material Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Geng, Xiao-peng [Inner Mongolia Baotou Steel Rare Earth Magnetic Materials Co.Ltd, Baotou 014030 (China); Hu, Feng-xia; Sun, Ji-rong; Shen, Bao-gen [State Key Laboratory for Magnetism, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)
2017-03-15
Magnetic materials of MM-Fe-B (MM=mischmetal) ribbons were prepared using melt spinning method by varying the content of MM. The ribbons contain minor phases besides the main phase of Re{sub 2}Fe{sub 14}B. X-ray techniques show that the diffraction peak intensities of the minor phase Fe{sub 3}B vary with the content of constituent elements, indicating that the amount of minor phase could be tunable. The squareness of hysteresis loop is the best in MM{sub 13}Fe{sub 80.5}B{sub 6.5} ribbons, which should mainly ascribe to the less amount of minor phase. Henkel plots verify the more uniform magnetization reversals in MM{sub 13}Fe{sub 80.5}B{sub 6.5} ribbons, and the energy product achieves to the maximum of 12.74 MGOe with the coercivity of 6.50 kOe. With the increase of MM content the coercivity increases monotonically, and reaches to 9.13 kOe in MM{sub 15}Fe{sub 77.5}B{sub 7.5} ribbons, which should be related with the nature of the defects in the main phase. These investigations show that optimizing the content of constituent elements and phase constitution could improve magnetic properties in the resource-saving magnets of MM-Fe-B ribbons. - Highlights: • MM-Fe-B (MM=mischmetal) ribbons contains the minor phases besides the main phase of Re{sub 2}Fe{sub 14}B. • The amount of minor phases varies with the content of constituent elements. • The energy product of 12.74 MGOe is obtained in MM{sub 13}Fe{sub 80.5}B{sub 6.5} ribbons by optimizing the phase constitution.
Solid-solution stability and preferential site-occupancy in (R-R′){sub 2}Fe{sub 14}B compounds
Energy Technology Data Exchange (ETDEWEB)
Colin, C. V.; Dempsey, N. M. [CNRS, Inst NEEL, F-38000 Grenoble (France); Univ. Grenoble Alpes, Inst NEEL, F-38000 Grenoble (France); Ito, M. [CNRS, Inst NEEL, F-38000 Grenoble (France); Univ. Grenoble Alpes, Inst NEEL, F-38000 Grenoble (France); Advanced Material Engineering Div., Toyota Motor Corporation, Susono 410-1193 (Japan); Yano, M. [Advanced Material Engineering Div., Toyota Motor Corporation, Susono 410-1193 (Japan); Suard, E. [Institut Laue-Langevin, CS 20156-38042 Grenoble cedex 9 (France); Givord, D. [CNRS, Inst NEEL, F-38000 Grenoble (France); Univ. Grenoble Alpes, Inst NEEL, F-38000 Grenoble (France); Instituto de Fisica, Universidade Federal do Rio de Janeiro, 21941-972 Rio de Janeiro (Brazil)
2016-06-13
The rare-earth (R) uniaxial anisotropy of R{sub 2}Fe{sub 14}B compounds with magnetic R atoms (e.g., Nd or Pr) is at the origin of the exceptional hard magnetic properties achieved in magnets based on these compounds. The uniaxial anisotropy found in Ce{sub 2}Fe{sub 14}B is attributed mainly to the magnetism of Fe. Ce is the most abundant R element and there has been much recent effort to fabricate magnets in which Ce is partially substituted for Nd. In the present neutron study of (R{sub 1−x}Ce{sub x}){sub 2}Fe{sub 14}B (R = La or Nd), Ce is found to enter the R{sub 2}Fe{sub 14}B phase over the entire composition range. The crystallographic parameters decrease with increasing Ce content and the Ce atoms preferentially occupy the smaller 4f sites. It is concluded that Ce in these (RR′){sub 2}Fe{sub 14}B compounds essentially maintains the intermediate valence character found in Ce{sub 2}Fe{sub 14}B. It is proposed that, in this intermediate valence state, Ce weakly contributes to uniaxial anisotropy, thus making a link with the fact that significant coercivity is preserved in Ce-substituted NdFeB magnets.
Site-specific magnetic anisotropies in R2Fe14B systems
Yoshioka, T.; Tsuchiura, H.
2018-04-01
The local magnetic anisotropy of R ions in R2Fe14B (R = Dy, Ho) systems is studied based on a microscopic effective spin model constructed from the information obtained by using first-principles calculations. By taking into account up to 6-th order crystal electric field parameters, the model satisfactory describes the observed magnetization curves and the temperature dependence of anisotropy constants. We found that at low temperatures, the noncollinear structure appears in the Ho2Fe14B system reflecting the local magnetic anisotropy.
Energy Technology Data Exchange (ETDEWEB)
Grabias, A., E-mail: agnieszka.grabias@itme.edu.pl [Institute of Electronic Materials Technology, Wólczyńska 133, 01-919 Warsaw (Poland); Kopcewicz, M. [Institute of Electronic Materials Technology, Wólczyńska 133, 01-919 Warsaw (Poland); Latuch, J.; Oleszak, D. [Faculty of Materials Science and Engineering, Warsaw University of Technology, Wołoska 141, 02-507 Warsaw (Poland); Pękała, M. [Department of Chemistry, University of Warsaw, Al. Żwirki i Wigury 101, 02-089 Warsaw (Poland); Kowalczyk, M. [Faculty of Materials Science and Engineering, Warsaw University of Technology, Wołoska 141, 02-507 Warsaw (Poland)
2017-07-15
Highlights: • Nanocomposite alloys were formed by annealing of the rapidly quenched alloys. • Magnetically hard L1{sub 0} (Fe,Co)Pt and soft (Fe,Co){sub 2}B or (Fe,Co)B were formed. • Mössbauer spectra revealed Co substitution for Fe in L1{sub 0} FePt, FeB and Fe{sub 2}B phases. • Annealed alloys exhibit hard magnetic properties which depend on phase compositions. • Co addition was found to decrease the magnetization and the energy product. - Abstract: The influence of Co content on the structural and hard magnetic properties of two sets of nanocrystalline Fe{sub 52−x}Co{sub x}Pt{sub 28}B{sub 20} (x = 0–26) and Fe{sub 60−y}Co{sub y}Pt{sub 25}B{sub 15} (y = 0–40) alloys was studied. The alloys were prepared as ribbons by the rapid quenching technique. The nanocomposite structure in the alloys was obtained by annealing at 840–880 K for 30 min. Structural characterization of the samples was performed using the Mössbauer spectroscopy and X-ray diffraction. Magnetic properties of the samples were studied by the measurements of the hysteresis loops and of the magnetization at increasing temperatures. An amorphous phase prevailed in the as-quenched Fe{sub 52−x}Co{sub x}Pt{sub 28}B{sub 20} alloys while a disordered solid solution of fcc-(Fe,Co)Pt was a dominating phase in the Fe{sub 60−y}Co{sub y}Pt{sub 25}B{sub 15} ribbons. Differential scanning calorimetry measurements revealed one or two exothermic peaks at temperatures up to 993 K, depending on the composition of the alloys. Thermal treatment of the samples led to the formation of the magnetically hard ordered L1{sub 0} tetragonal (Fe,Co)Pt nanocrystallites and magnetically softer phases of (Fe,Co)B (for Fe{sub 52−x}Co{sub x}Pt{sub 28}B{sub 20}) or (Fe,Co){sub 2}B (for Fe{sub 60−y}Co{sub y}Pt{sub 25}B{sub 15}). Detailed Mössbauer spectroscopy studies revealed that cobalt substituted for iron in both the L1{sub 0} phase and in iron borides. The nanocomposite Fe{sub 60−y}Co{sub y
Crystallization of Fe83B17 amorphous alloy by electric pulses produced by a capacitor discharge
International Nuclear Information System (INIS)
Georgarakis, Konstantinos; Dudina, Dina V.; Mali, Vyacheslav I.; Anisimov, Alexander G.; Bulina, Natalia V.; Moreira Jorge, Alberto Jr.; Yavari, Alain R.
2015-01-01
Heating of conductive materials by electric current is used in many technological processes. Application of electric pulses to metallic glasses induces their fast crystallization, which is an interesting and complex phenomenon. In this work, crystallization of the Fe 83 B 17 amorphous alloy induced by pulses of electric current produced has been studied using X-ray diffraction and transmission electron microscopy. Ribbons of the alloy were directly subjected to single pulses of electric current 250 μs long formed by a capacitor discharge. As the value of ∫I 2 dt was increased from 0.33 to 2.00 A 2 s, different crystallization stages could be observed. The crystallization began through the formation of the nuclei of α-Fe. At high values of ∫I 2 dt, α-Fe and tetragonal and orthorhombic Fe 3 B and Fe 23 B 6 were detected in the crystallized ribbons with crystallites of about 50 nm. Thermal annealing of the ribbons at 600 C for 2 min resulted in the formation of α-Fe and tetragonal Fe 3 B. It was concluded that pulses of electric current produced by a capacitor discharge induced transformation of the Fe 83 B 17 amorphous phase into metastable crystalline products. (orig.)
Prediction of particle orientation in simple upsetting process of NdFeB magnets
Energy Technology Data Exchange (ETDEWEB)
Chang, Chao-Cheng; Hsiao, Po-Jen [Department of Mold and Die Engineering, National Kaohsiung University of Applied Sciences, 415 Chien-Kung Road, Sanmin District, Kaohsiung 80778, Taiwan (China); You, Jr-Shiang; Chen, Yen-Ju; Chang, Can-Xun [Metal Forming Technology Section, Metal Processing R and D Department, Metal Industries Research and Development Centre, 1001 Kaonan Highway, Kaohsiung 81160, Taiwan (China)
2013-12-16
The magnetic properties of NdFeB magnets are strongly affected by crystallographic texture which is highly associated with particle orientation. This study proposed a method for predicting the particle orientation in the simple upsetting process of NdFeB magnets. The method is based on finite element simulation with flow net analysis. The magnets in a cylindrical form were compressed by two flat dies in a chamber filled with argon at 750°C. Three forming speeds were taken into account in order to obtain flow stress curves used in simulations. The micrographs of the cross sections of the deformed magnets show that the particle deformation significantly increases with the compression. The phenomenon was also predicted by the proposed method. Both simulated and experimental results show that the inhomogeneity of the texture of the NdFeB magnets can be increased by the simple upsetting process. The predicted particle orientations were in a good agreement with those examined in the deformed magnets. The proposed method for predicting particle orientations can also be used in other forming processes of NdFeB magnets.
Prediction of particle orientation in simple upsetting process of NdFeB magnets
International Nuclear Information System (INIS)
Chang, Chao-Cheng; Hsiao, Po-Jen; You, Jr-Shiang; Chen, Yen-Ju; Chang, Can-Xun
2013-01-01
The magnetic properties of NdFeB magnets are strongly affected by crystallographic texture which is highly associated with particle orientation. This study proposed a method for predicting the particle orientation in the simple upsetting process of NdFeB magnets. The method is based on finite element simulation with flow net analysis. The magnets in a cylindrical form were compressed by two flat dies in a chamber filled with argon at 750°C. Three forming speeds were taken into account in order to obtain flow stress curves used in simulations. The micrographs of the cross sections of the deformed magnets show that the particle deformation significantly increases with the compression. The phenomenon was also predicted by the proposed method. Both simulated and experimental results show that the inhomogeneity of the texture of the NdFeB magnets can be increased by the simple upsetting process. The predicted particle orientations were in a good agreement with those examined in the deformed magnets. The proposed method for predicting particle orientations can also be used in other forming processes of NdFeB magnets
Investigation on demagnetization of Nd2Fe14B permanent magnets induced by irradiation
Li, Zhefu; Jia, Yanyan; Liu, Renduo; Xu, Yuhai; Wang, Guanghong; Xia, Xiaobin
2017-12-01
Nd2Fe14B is an important component of insertion devices, which are used in synchrotron radiation sources, and could be demagnetized by irradiation. In the present study, the Monte Carlo code FLUKA was used to analyze the irradiation field of Nd2Fe14B, and it was confirmed that the main demagnetization particle was neutron. Nd2Fe14B permanent magnet samples were irradiated by Ar ions at different doses to simulate neutron irradiation damage. The hysteresis loops were measured using a vibrating sample magnetometer, and the microstructure evolutions were characterized by transmission electron microscopy. Moreover, the relationship between them was discussed. The results indicate that the decrease in saturated magnetization is caused by the changes in microstructure. The evolution of single crystals into an amorphous structure is the reason for the demagnetization phenomenon of Nd2Fe14B permanent magnets when considering its microscopic structure.
Oliveira, Danniel Ferreira de
2009-01-01
Ligas Cu-Al-Ni e Cu-Al-Be forma elaboradas sob atmosfera ambiente e caracterizadas por microscopia, difração de R-X e Calorimetria Diferencial de varredura. Foram realizados nestas ligas ensaios de tração, recuperação de forma e superelasticidade. As propriedades termomecânicas destas ligas realizadas em diferentes temperaturas permitiu concluir que as ligas Cu-Al-Ni podem ser utilizadas como atuadores mecânicos para temperaturas acima de 90°C e que estas ligas não devem ser empregadas em tem...
Mumtaz, Fiza; Jaffari, G. Hassnain; Hassan, Qadeer ul; Shah, S. Ismat
2018-06-01
We present detailed comparative study of effect of isovalent i.e. Eu+3 substitution at A-site and tetra (Ti+4, Zr+4), penta (V+5) and hexavalent (W+6) substitutions at B-site in BiFeO3. Eu+3 substitution led to phase transformation and exhibited mixed phases i.e. rhombohedral and orthorhombic, while tetravalent substituents (Ti+4 and Zr+4) led to stabilization of cubic phase. In higher valent (i.e. V+5 and W+6) cases solubility limit was significantly reduced where orthorhombic phase was observed as in the case of parent compound. Phase transformation as a consequence of increase in microstrain and chemical pressure induced by the substituent has been discussed. Solubility limit of different B-site dopants i.e. Zr, W and V was extracted to 5%, 2% and 2%, respectively. Extra phases in various cases were Bi2Fe4O9, Bi25FeO40, Bi14W2O27, and Bi23V4O44.5 and their fractional amount have been quantified. Ti was substituted up to 15% and has been observed to be completely soluble in the parent compound. Solubility limits depends on ionic radii mismatch and valance difference of Fe+3 and dopant, in which valance difference plays more dominant role. Solubility limit and phase transformation has been explained in terms of change in bond strength and tolerance factor induced by incorporation of dopant which depend on its size and valence state. Detail optical, dielectric, ferroelectric, magnetic and transport properties of Eu and Ti co-doped samples and selected low concentration B-site doped compositions (i.e. 2%) have presented and discussed. Two d-d transitions and three charge transfer transitions were observed within UV-VIS range. Both change in cell volume for the same phase and transformation in crystal structure affects the band gap. Increase in room temperature dielectric constant and saturation polarization was also found to increase in case of Eu-Ti co-doped samples with increasing concentration of Ti. Substitution of Eu at A-site and Ti at B-site led to
Binder Jetting: A Novel NdFeB Bonded Magnet Fabrication Process
Paranthaman, M. Parans; Shafer, Christopher S.; Elliott, Amy M.; Siddel, Derek H.; McGuire, Michael A.; Springfield, Robert M.; Martin, Josh; Fredette, Robert; Ormerod, John
2016-07-01
The goal of this research is to fabricate near-net-shape isotropic (Nd)2Fe14B-based (NdFeB) bonded magnets using a three dimensional printing process to compete with conventional injection molding techniques used for bonded magnets. Additive manufacturing minimizes the waste of critical materials and allows for the creation of complex shapes and sizes. The binder jetting process works similarly to an inkjet printer. A print-head passes over a bed of NdFeB powder and deposits a polymer binding agent to bind the layer of particles together. The bound powder is then coated with another layer of powder, building the desired shape in successive layers of bonded powder. Upon completion, the green part and surrounding powders are placed in an oven at temperatures between 100°C and 150°C for 4-6 h to cure the binder. After curing, the excess powder can be brushed away to reveal the completed "green" part. Green magnet parts were then infiltrated with a clear urethane resin to achieve the measured density of the magnet of 3.47 g/cm3 close to 46% relative to the NdFeB single crystal density of 7.6 g/cm3. Magnetic measurements indicate that there is no degradation in the magnetic properties. This study provides a new pathway for preparing near-net-shape bonded magnets for various magnetic applications.
Influence of an external magnetic field on damage by self-ion irradiation in Fe90Cr10 alloy
Directory of Open Access Journals (Sweden)
Fernando José Sánchez
2016-12-01
Full Text Available The effect of an external magnetic field (B=0.5 T on Fe90Cr10 specimens during Fe ion irradiation, has been investigated by means of Conversion Electron Mössbauer Spectroscopy (CEMS. The analysis has revealed significant differences in the average hyperfine magnetic field (=0.3 T between non-irradiated and irradiated samples as well as between irradiations made with B (w/ B and without B (w/o B. It is considered that these variations can be due to changes in the local environment around the probe nuclei (57Fe; where vacancies and Cr distribution play a role. The results indicate that the Cr distribution in the neighbourhood of the iron atoms could be changed by the application of an external field. This would imply that an external magnetic field may be an important parameter to take into account in predictive models for Cr behaviour in Fe–Cr alloys, and especially in fusion conditions where intense magnetic fields are required for plasma confinement.
Directory of Open Access Journals (Sweden)
Jarosław Pasek
2012-04-01
Full Text Available Wstęp: Rwa kulszowa, ischialgia (łac. ischias to zespół objawów związanych z uciskiem na przebiegu nerwów rdzeniowych L4, L5 lub S1 tworzących nerw kulszowy. Wiedza na temat leczenia zmienia się radykalnie i coraz częściej w leczeniu stosuje się wybrane metody fizykoterapeutyczne. W ostatnich latach ukazuje się coraz więcej publikacji dotyczących praktycznego wykorzystania w medycynie pól magnetycznych niskiej częstotliwości. Duża różnorodność wskazań oraz zastosowań w praktyce przynosi szerokie spektrum możliwości leczniczych. Materiał i metoda: Badaniami objęto grupę 47 pacjentów z rozpoznaniem rwy kulszowej spowodowanej zmianami zwyrodnieniowymi krążka międzykręgowego. Pacjentów podzielono na 3 grupy badawcze i poddano odpowiednio zabiegom magnetoterapii, magnetostymulacji i magnetoledoterapii w celu porównania przeprowadzonej terapii. Dokonano subiektywnej oceny odczuwanych dolegliwości bólowych w skali VAS. Dodatkowo posłużono się ankietą, w której oceniono częstość zażywania leków przeciwbólowych. Do oceny jakości życia wykorzystano skalę EuroQol. U każdego pacjenta podczas badania fizykalnego wykonano test Lasègue’a. Wyniki: Wykazano statystyczne zmniejszenie nasilenia odczuwanych dolegliwości bólowych w skali VAS badanych pacjentów (p<0,01, znaczną redukcję zażywanych leków przeciwbólowych oraz poprawę jako- ści życia ocenianej w skali EuroQol (p<0,01 po zastosowaniu zabiegów pola magnetycznego niskiej częstotliwości. Wnioski: Terapia polem magnetycznym bez względu na zastosowaną metodę zmniejsza odczuwane dolegliwości bólowe, co wpływa na poprawę jakości życia leczonych chorych. Zastosowana terapia przyczynia się również do ograniczenia przyjmowania leków przeciwbólowych. W badaniu nie stwierdzono znaczącej przewagi którejś z analizowanych metod w odniesieniu do otrzymanych wyników leczenia.
Crystal structure and magnetism of Fe2(OH)[B2O4(OH)
DEFF Research Database (Denmark)
Kurayoshi, Yotaro; Hara, Shigeo; Sato, Hirohiko
2014-01-01
The structure and magnetism of Fe2(OH)[B2O4(OH)] are reported. Powder x-ray diffraction reveals a characteristic structure containing two crystallographically independent zigzag-ladder chains of magnetic Fe2+ ions. Magnetization measurements reveal a phase transition at 85 K, below which a weak...... spontaneous magnetization (approximate to 0.15 μB/Fe) appears. Below 85 K, magnetization increases with decreasing temperature down to 70 K, below which it decreases and approaches a constant value at low temperature. The Mossbauer spectrum at room temperature is composed of two paramagnetic doublets...... corresponding to the two crystallographic Fe2+ sites. Below 85 K, each doublet undergoes further splitting because of the magnetic hyperfine fields. The temperature dependence of the hyperfine field is qualitatively different for the two distinguishable Fe2+ sites. This is responsible for the anomalous...
A study of coFeB magnetic yoke based on planar electromagnet
Qin, L.; Li, Q.; Yuan, Yong J.
2017-07-01
This paper studies the fabrication of a novel planar electromagnet consisting of a planar copper coil and a magnetic yoke. CoFeB was used as the magnetic yoke material instead of the traditional permanent magnets. The planar electromagnet was fabricated and optimized to maximize the electromagnetic force, especially with varying CoFeB thickness. The micro-planar electromagnet was fabricated successfully by the traditional micro-electro-mechanical-system (MEMS) techniques and XRD, VSM were used to characterize the performance of the electromagnet. The planar electromagnet exhibits superior perpendicular magnetic anisotropy (PMA) and 0.006 emu of MS was achieved following 2 min deposition of CoFeB thin film. By integrating with other micro apparatuses, it is anticipated that the planar electromagnet will have potential applications in areas such as biosensors, biological medicine, drug delivery, chemical analysis and environmental monitoring.
First-order-reversal-curve analysis of exchange-coupled SmCo/NdFeB nanocomposite alloys
International Nuclear Information System (INIS)
Pan, Mingxiang; Zhang, Pengyue; Ge, Hongliang; Yu, Nengjun; Wu, Qiong
2014-01-01
Exchange-coupled SmCo 5 /Nd 2 Fe 14 B nanocomposite magnets have been fabricated by ball milling of the micrometer sized SmCo 5 and Nd 2 Fe 14 B powders. The influence of Nd 2 Fe 14 B content on the microstructure and magnetic properties of these hybrid alloys was investigated. The alloys that show strong intergrain exchange-coupling behavior with (BH) max =2.95 MGOe was obtained when the two hard phases are well coupled. A first-order-reversal-curve (FORC) analysis was performed for both SmCo 5 single-phase magnet and SmCo 5 /Nd 2 Fe 14 B hybrid magnet; the FORC diagrams results show two major peaks for the hybrid magnets. In both cases, the magnetization reversal behaviors for these alloys were discussed in detail and are consistent with the results of δM plots. - Highlights: • Exchange-coupled SmCo 5 /Nd 2 Fe 14 B nanocomposite magnets were studied. • Magnetization reversal behaviors of the hybrid magnet were discussed. • The FORCs analysis is taken to identify the optimal conditions for hybrid magnet
Development of NdFeB magnet through hydrogen decrepitation
International Nuclear Information System (INIS)
Akhtar, S.; Farooque, M.; Haider, A.; Ahmad, Z.
2009-01-01
Neodymium based magnets are the powerful permanent magnet of today. This paper will discuss iron based rare earth magnets. NdFeB sintered magnet material has been developed. The magnets are produced by powder metallurgy route involving hydrogen decrepitation technique for making fine powder. After melting and casting, the NdFeB alloy is subject to hydrogen atmosphere. Hydrogen slowly absorbs into the solid alloy and makes it brittle, which upon milling becomes fine powder. Hydrogen is then removed by placing the powder at temperature around 800 deg. C under vacuum. Then the powders are pressed under isostatic conditions and sintered at temperature range of 1020-1050 deg. C. Post sintering is done at 800 deg. C and 580 deg. C followed by quenching. Energy product in the range of 8 MGOe is achieved. (author)
Flux pinning and inhomogeneity in magnetic nanoparticle doped MgB2/Fe wires
Novosel, Nikolina; Pajić, Damir; Mustapić, Mislav; Babić, Emil; Shcherbakov, Andrey; Horvat, Joseph; Skoko, Željko; Zadro, Krešo
2010-06-01
The effects of magnetic nanoparticle doping on superconductivity of MgB2/Fe wires have been investigated. Fe2B and SiO2-coated Fe2B particles with average diameters 80 and 150 nm, respectively, were used as dopands. MgB2 wires with different nanoparticle contents (0, 3, 7.5, 12 wt.%) were sintered at temperature 750°C. The magnetoresistivity and critical current density Jc of wires were measured in the temperature range 2-40 K in magnetic field B doped wires decreases quite rapidly with doping level (~ 0.5 K per wt.%). This results in the reduction of the irreversibility fields Birr(T) and critical current densities Jc(B,T) in doped samples (both at low (5 K) and high temperatures (20 K)). Common scaling of Jc(B,T) curves for doped and undoped wires indicates that the main mechanism of flux pinning is the same in both types of samples. Rather curved Kramer's plots for Jc of doped wires imply considerable inhomogeneity.
NdFeB alloy as a magnetic electrode material for lithium-ion batteries
International Nuclear Information System (INIS)
Zhang, J.; Shui, J.L.; Zhang, S.L.; Wei, X.; Xiang, Y.J.; Xie, S.; Zhu, C.F.; Chen, C.H.
2005-01-01
The search for a reliable indicator of state of charge and even the remaining energy of a lithium-ion cell is of great importance for various applications. This study was an exploratory effort to use magnetic susceptibility as the indicator. In this work, for the first time the change of ac susceptibility of cells was in situ monitored during charge-discharge process. A strong permanent magnetic material, NdFeB alloy, was investigated as an anode material for rechargeable lithium batteries. Both original and partially oxidized NdFeB powders were made into electrodes. Structural characterization was performed on the NdFeB electrodes by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis. An alloy (core)-oxide (shell) structure was found for those partially oxidized samples. The electrochemical cycling of cells made of the NdFeB electrodes against lithium was measured. The first lithium intercalation capacity of a treated NdFeB can be up to about 831 mAh/g, while a rather reversible capacity of up to 352 mAh/g can be obtained. With a specially designed cell, we were able to monitor in situ the change of relative ac susceptibility during charge and/or discharge steps. A clearly monotonous relationship is found between the ac susceptibility of a cell and its depth-of-discharge (DOD). A mechanism based on skin effect and eddy current change is proposed to explain this susceptibility versus DOD relationship
NdFeB alloy as a magnetic electrode material for lithium-ion batteries
Energy Technology Data Exchange (ETDEWEB)
Zhang, J. [Department of Materials Science and Engineering, University of Science and Technology of China, Anhui Hefei 230026 (China); Shui, J.L. [Department of Materials Science and Engineering, University of Science and Technology of China, Anhui Hefei 230026 (China); Zhang, S.L. [Department of Materials Science and Engineering, University of Science and Technology of China, Anhui Hefei 230026 (China); Wei, X. [Department of Materials Science and Engineering, University of Science and Technology of China, Anhui Hefei 230026 (China); Xiang, Y.J. [Department of Materials Science and Engineering, University of Science and Technology of China, Anhui Hefei 230026 (China); Xie, S. [Department of Materials Science and Engineering, University of Science and Technology of China, Anhui Hefei 230026 (China); Zhu, C.F. [Department of Materials Science and Engineering, University of Science and Technology of China, Anhui Hefei 230026 (China); Chen, C.H. [Department of Materials Science and Engineering, University of Science and Technology of China, Anhui Hefei 230026 (China)]. E-mail: cchchen@ustc.edu.cn
2005-04-05
The search for a reliable indicator of state of charge and even the remaining energy of a lithium-ion cell is of great importance for various applications. This study was an exploratory effort to use magnetic susceptibility as the indicator. In this work, for the first time the change of ac susceptibility of cells was in situ monitored during charge-discharge process. A strong permanent magnetic material, NdFeB alloy, was investigated as an anode material for rechargeable lithium batteries. Both original and partially oxidized NdFeB powders were made into electrodes. Structural characterization was performed on the NdFeB electrodes by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis. An alloy (core)-oxide (shell) structure was found for those partially oxidized samples. The electrochemical cycling of cells made of the NdFeB electrodes against lithium was measured. The first lithium intercalation capacity of a treated NdFeB can be up to about 831 mAh/g, while a rather reversible capacity of up to 352 mAh/g can be obtained. With a specially designed cell, we were able to monitor in situ the change of relative ac susceptibility during charge and/or discharge steps. A clearly monotonous relationship is found between the ac susceptibility of a cell and its depth-of-discharge (DOD). A mechanism based on skin effect and eddy current change is proposed to explain this susceptibility versus DOD relationship.
[The cytotoxicity of N48 NdFeB magnets coated with titanium-nitride].
Cao, Xiao-Ming; Hou, Zhi-Ming; Chu, Ming
2008-04-01
To evaluate the effect of N48 NdFeB magnets coated with titanium-nitride on the growth and apoptosis of L929 mouse fibroblast cells, and to determine the material biocompatibility. The NdFeB magnets coated with titanium-nitride, bare NdFeB magnets and ordinary brackets were put into RPMI-1640 to prepare fusions. L929 mouse fibroblast cells were cultivated in the negative control liquid, positive control liquid, 100%, 50% and 25% sample fusions, respectively. The cell proliferation vitality was detected by MTT assay and the relative growth rate was calculated.Cell scatter diagrams of the negative control liquid, 100% titanium-nitride coated magnets fusion and bare magnets fusion were detected by flow cytometry Annexin V/PI double staining method. The ratios of normal cells, early apoptosis, advanced apoptosis and necrosis cells were calculated. The results were analyzed for paired t test using SPSS11.5 software package. The toxic levels of N48 NdFeB coated with titanium-nitride were ranked as 0-1. The toxic levels of bare magnets were ranked as 2. The cell scatter diagrams showed that there was no significant difference in living cell, early apoptosis and necrosis between magnets coated with titanium-nitride and control group. But there was significant difference between the bare magnets group and control group. The N48 NdFeB magnets coated with titanium-nitride have good biocompatibility.
Effect of annealing on the magnetic properties and microstructure of NdFeB/Tb multilayered films
Energy Technology Data Exchange (ETDEWEB)
Li, D S; Suzuki, S; Liu, W F; Horikawa, T; Machida, K [Center for Advanced Science and Innovation, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565-0871 (Japan)], E-mail: machida@casi.osaka-u.ac.jp
2009-02-01
The magnetic properties of NdFeB/Tb multilayered films annealed at 773-1273K were investigated by evaluating the effect of Tb spacer layer and comparing them with those of NdFeB single layered films. The as-deposited NdFeB/Tb film with a amorphous structure was crystallized at the higher annealing temperature than 923K and Nd-rich phases were formed at 1073 K, meanwhile the coercivity increased substantially. By observations of the microstructure, Tb element was found to diffuse into the Nd-rich phases to form a Tb-enriched phase around the Nd{sub 2}Fe{sub 14}B primary phase particles in the multilayered films.
Effect of annealing on the magnetic properties and microstructure of NdFeB/Tb multilayered films
International Nuclear Information System (INIS)
Li, D S; Suzuki, S; Liu, W F; Horikawa, T; Machida, K
2009-01-01
The magnetic properties of NdFeB/Tb multilayered films annealed at 773-1273K were investigated by evaluating the effect of Tb spacer layer and comparing them with those of NdFeB single layered films. The as-deposited NdFeB/Tb film with a amorphous structure was crystallized at the higher annealing temperature than 923K and Nd-rich phases were formed at 1073 K, meanwhile the coercivity increased substantially. By observations of the microstructure, Tb element was found to diffuse into the Nd-rich phases to form a Tb-enriched phase around the Nd 2 Fe 14 B primary phase particles in the multilayered films.
Kruger, Larisa C.; O'Malley, Heather A.; Hull, Jacob M.; Kleeman, Amanda; Patino, Gustavo A.
2016-01-01
Voltage-gated sodium channel (VGSC) β subunits signal through multiple pathways on multiple time scales. In addition to modulating sodium and potassium currents, β subunits play nonconducting roles as cell adhesion molecules, which allow them to function in cell–cell communication, neuronal migration, neurite outgrowth, neuronal pathfinding, and axonal fasciculation. Mutations in SCN1B, encoding VGSC β1 and β1B, are associated with epilepsy. Autosomal-dominant SCN1B-C121W, the first epilepsy-associated VGSC mutation identified, results in genetic epilepsy with febrile seizures plus (GEFS+). This mutation has been shown to disrupt both the sodium-current-modulatory and cell-adhesive functions of β1 subunits expressed in heterologous systems. The goal of this study was to compare mice heterozygous for Scn1b-C121W (Scn1b+/W) with mice heterozygous for the Scn1b-null allele (Scn1b+/−) to determine whether the C121W mutation results in loss-of-function in vivo. We found that Scn1b+/W mice were more susceptible than Scn1b+/− and Scn1b+/+ mice to hyperthermia-induced convulsions, a model of pediatric febrile seizures. β1-C121W subunits are expressed at the neuronal cell surface in vivo. However, despite this, β1-C121W polypeptides are incompletely glycosylated and do not associate with VGSC α subunits in the brain. β1-C121W subcellular localization is restricted to neuronal cell bodies and is not detected at axon initial segments in the cortex or cerebellum or at optic nerve nodes of Ranvier of Scn1bW/W mice. These data, together with our previous results showing that β1-C121W cannot participate in trans-homophilic cell adhesion, lead to the hypothesis that SCN1B-C121W confers a deleterious gain-of-function in human GEFS+ patients. SIGNIFICANCE STATEMENT The mechanisms underlying genetic epilepsy syndromes are poorly understood. Closing this gap in knowledge is essential to the development of new medicines to treat epilepsy. We have used mouse models to
Improved room-temperature-selectivity between Nd and Fe in Nd recovery from Nd-Fe-B magnet
Energy Technology Data Exchange (ETDEWEB)
Kataoka, Y.; Kitagawa, J., E-mail: j-kitagawa@fit.ac.jp [Department of Electrical Engineering, Faculty of Engineering, Fukuoka Institute of Technology, 3-30-1 Wajiro-higashi, Higashi-ku, Fukuoka 811-0295 (Japan); Ono, T.; Tsubota, M. [Physonit Inc., 6-10 Minami-Horikawa, Kaita Aki, Hiroshima 736-0044 (Japan)
2015-11-15
The sustainable society requires the recycling of rare metals. Rare earth Nd is one of rare metals, accompanying huge consumption especially in Nd-Fe-B magnets. Although the wet process using acid is in practical use in the in-plant recycle of sludge, higher selectivity between Nd and Fe at room temperature is desired. We have proposed a pretreatment of corrosion before the dissolution into HCl and the oxalic acid precipitation. The corrosion produces γ-FeOOH and a Nd hydroxide, which have high selectivity for HCl solution at room temperature. Nd can be recovered as Mn{sub 2}O{sub 3}-type Nd{sub 2}O{sub 3}. The estimated recovery-ratio of Nd reaches to 97%.
Improved room-temperature-selectivity between Nd and Fe in Nd recovery from Nd-Fe-B magnet
Directory of Open Access Journals (Sweden)
Y. Kataoka
2015-11-01
Full Text Available The sustainable society requires the recycling of rare metals. Rare earth Nd is one of rare metals, accompanying huge consumption especially in Nd-Fe-B magnets. Although the wet process using acid is in practical use in the in-plant recycle of sludge, higher selectivity between Nd and Fe at room temperature is desired. We have proposed a pretreatment of corrosion before the dissolution into HCl and the oxalic acid precipitation. The corrosion produces γ-FeOOH and a Nd hydroxide, which have high selectivity for HCl solution at room temperature. Nd can be recovered as Mn2O3-type Nd2O3. The estimated recovery-ratio of Nd reaches to 97%.
Directory of Open Access Journals (Sweden)
Marcia Flores da Silva
2007-08-01
Full Text Available The objective of this work was to validate microsatellite markers associated with resistance to soybean cyst nematode (Heterodera glycines Ichinohe races 3 and 14, in soybean (Glycine max L. genotypes, for use in marker-assisted selection (MAS programs. Microsatellites of soybean linkage groups A2, D2 and G were tested in two populations, and their selection efficiencies were determined. The populations were 65 F2:3 families from Msoy8001 (resistant x Conquista (susceptible cross, and 66 F2:3 families of S5995 (resistant x Renascença (susceptible cross, evaluated for resistance to races 3 and 14, respectively. Families with female index up to 30% were considered moderately resistant. Markers of A2 and G linkage groups were associated with resistance to race 3. Markers Satt309 and GMENOD2B explained the greatest proportion of phenotypic variance in the different groups. The combinations Satt309+GMENOD2B and Satt309+Satt187 presented 100% selection efficiency. Resistance to race 14 was associated with markers of G linkage group, and selection efficiency in the Satt309+Satt356 combination was 100%. The selection differential obtained by phenotypic and marker assisted selection showed that both can result in similar gains.O objetivo deste trabalho foi validar marcadores microssatélites associados à resistência às raças 3 e 14 do nematóide-de-cisto (Heterodera glycines Ichinohe da soja (Glycine max L., para serem utilizados em programas de seleção assistida por marcadores moleculares (SAM. Microssatélites dos grupos de ligação A2, D2 e G da soja foram testados em duas populações, e suas eficiências de seleção foram determinadas. As populações foram 65 famílias F2:3, do cruzamento Msoy8001 (resistente x Conquista (suscetível, e 66 famílias F2:3, do cruzamento S5995 (resistente x Renascença (suscetível, avaliadas para a resistência às raças 3 e 14, respectivamente. Famílias com índice de fêmeas de até 30% foram
Electron microscopy investigations of rapidly solidified Fe-Zr-B-Cu alloys
International Nuclear Information System (INIS)
Majumdar, B.; Arvindha Babu, D.; Akhtar, D.
2010-01-01
Rapidly solidified Fe-based nanocrystalline soft magnetic materials possess a unique combination of properties i,e high permeability, saturation and Curie temperature and very low coercivity which are otherwise not attainable in conventional soft magnetic materials. The alloys are processed by producing amorphous phase through melt spinning route followed by a partial devitrification for incorporation of nanocrystalline phase in the amorphous matrix. In this paper, detailed electron microscopic investigations of melt spun Fe-Zr-B-Cu alloys are presented. Melt spun ribbons of Fe 99-x-y Zr x BCu 1 alloys with x+y = 11 and x+y = 13 were prepared under different wheel speed conditions and then vacuum annealed for 1 h at different temperatures. The microstructure changes from completely amorphous to a cellular/dendritic bcc solid solution coexisting with the amorphous phase at intercellular/dendritic regions when Zr/B ratio or the process parameters are varied. Annealing leads to the precipitation of nanocrystalline bcc-Fe phase from both amorphous phase and already existing bcc solid solution. (author)
Cold compaction behavior of nano-structured Nd-Fe-B alloy powders prepared by different processes
Energy Technology Data Exchange (ETDEWEB)
Liu, Xiaoya [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Hu, Lianxi, E-mail: hulx@hit.edu.cn [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Wang, Erde [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)
2013-02-25
Graphical abstract: Relative density enhancement and nanocrystallization of Nd{sub 2}Fe{sub 14}B phase are two major effective means to improve magnetic properties. Since the matrix Nd{sub 2}Fe{sub 14}B phase in the starting Nd-Fe-B alloy can be disproportionated into a nano-structured mixture of NdH{sub 2.7}, Fe{sub 2}B, and {alpha}-Fe phases during mechanical milling in hydrogen. It is thus important to study the densification behavior of nanocrystalline powders to evaluate and predict the cold compactibility of powders. By comparison with the as milled as well as melt-spun Nd{sub 16}Fe{sub 76}B{sub 8} alloy powders, we find that the as-disproportionated Nd{sub 16}Fe{sub 76}B{sub 8} alloy powder exhibits the best cold compactibility. As evident from the illustration presented below, compaction parameters (representing the powder compactibility) have been determined by fitting density-pressure data with double logarithm compaction equation. Densification mechanisms involved during cold compaction process are clarified in our work by referring to microstructure observation of samples prepared by various methods. As a result, highly densified green magnet compact can be obtained by cold pressing of as-disproportionated NdFeB alloy powders. Highlights: Black-Right-Pointing-Pointer Nano-structured disproportionated Nd-Fe-B alloy powders by mechanical milling in hydrogen. Black-Right-Pointing-Pointer Highly densified green magnet compact by cold pressing of as-disproportionated Nd-Fe-B alloy powders. Black-Right-Pointing-Pointer Density-pressure data fitted well by an empirical powder compaction model. Black-Right-Pointing-Pointer As-disproportionated powder showed better compactibility than as milled and melt-spun counterparts. Black-Right-Pointing-Pointer The effects of physical properties on powder compactibility and densification mechanisms are clarified. - Abstract: The compaction behavior of nano-structured Nd{sub 16}Fe{sub 76}B{sub 8} (atomic ratio) alloy
Wear behavior of the surface alloyed AISI 1020 steel with Fe-Nb-B by TIG welding technique
Kilinc, B.; Durmaz, M.; Abakay, E.; Sen, U.; Sen, S.
2015-03-01
Weld overlay coatings also known as hardfacing is a method which involves melting of the alloys and solidification for applied coatings. Recently hardfacing by welding has become a commonly used technique for improvement of material performance in extreme (high temperature, impact/abrasion, erosion, etc.) conditions.In the present study, the coatings were produced from a mixture of ferrous niobium, ferrous boron and iron powders in the ranges of -45µm particle size with different ratio. Fe12Nb5B3 and Fe2NbBalloys were coated on the AISI 1020 steel surface by TIG welding. The phases formed in the coated layer are Fe2B, NbB2, NbFeB and Fe0,2 Nb0,8 phases. The hardness of the presence phases are changing between 1689±85 HV0.01, and 181±7 HV0.1. Microstructural examinations were realized by optical and scanning electron microscopy. The wear and friction behaviors of Fe12Nb5B3 and Fe2NbB realized on the AISI 1020 steel were investigated by the technique of TIG welding by using ball-on-disk arrangement against alumina ball.
Shen, Yupeng; Huang, Zhifu; Jian, Yongxin; Yang, Ming; Li, Kemin
2018-03-01
Mo2FeB2 based cermets with and without PVA have been investigated by x-ray diffractometry (XRD), x-ray photoelectron spectroscope (XPS) and scanning electron microscopy (SEM). The density and transverse rupture strength (TRS) of green compact, relative density, hardness (HRA), fracture toughness (KIC) and TRS of Mo2FeB2 based cermets were also measured. The results indicate that, compared with the Mo2FeB2 based cermets without PVA, the density of green compact with PVA can be improved slightly at the same pressure. However, the much higher TRS is obtained for the green compact without PVA. Meanwhile, Mo2FeB2 particles exhibit the finer and less congruity feature for Mo2FeB2 based cermets without PVA. In addition, the higher relative density, hardness, fracture toughness and TRS can be acquired for the cermets without PVA. Obviously, considering the mechanical properties and preparation period of Mo2FeB2 based cermets, no adding PVA is the optimized process of powder molding in the manufacture of Mo2FeB2 based cermets.
The Role of Annealing Temperature on Structural and Magnetic Properties of NdFeB Thin Films
Directory of Open Access Journals (Sweden)
A. Khanjani
2016-06-01
Full Text Available In the present research NdFeB thin films coupled with buffer and capping layer of W were formed on Si/SiO2 substrate by means of RF magnetron sputtering. The system was annealed at vaccum at different temperatures of 450, 500, 550,. 600 and 650 °C Phase analysis was carried out by XRD and it was found that NdFeB was formed without the formation of any kind of secondary phase. The cross sectional and grain size of the thin films were measured by scanning electron microscopy. Morphological studies were performed by atomic force microscopy. Magnetic properties of thin films including coercivity, saturation of magnetization and hysteresis area were evcaluated by vibrating sample magnetometer. It was found that by annealing at 400 °C the amorphous layer was formed.The highest intensity of peaks was formed at 550 °C and with an increase in temperature the intensity was declined. The grain size was increased by temperature and had an impact on the coercivity. With an increase of temperature up to 600 °C, perpendicular coercivity was increased and then by further increase of temperatute, coercivity was reduced. Based on the obtained data the temperature of 600 °C was selected as the optimum annealing temperature for reaching enhanced structural and magnetic feature.
Magnetic and structural properties of the Nd2(Fe100-xNbx)14B system prepared by arc melting
International Nuclear Information System (INIS)
Oyola Lozano, D.; Zamora, L. E.; Perez Alcazar, G. A.; Rojas, Y. A.; Bustos, H.; Greneche, J. M.
2006-01-01
In this work the magnetic and structural properties are investigated by Moessbauer spectrometry, Vibrating Sample Magnetometry and X-ray diffraction of Nd 2 (Fe 100-x Nb x ) 14 B powdered alloys with x = 0, 2 and 4 prepared by arc melting. The Moessbauer spectra of the samples were fitted with several contributions from: Nd 2 Fe 14 B, α-Fe and a paramagnetic phase associated with Nd 1.1 Fe 4 B 4 for x = 0 and additionally from NbFeB and Nd 2 Fe 17 for x = 2 and x = 4. The relative fractions of α-Fe and Nd 2 Fe 14 B are smaller for x = 4 than for x = 0, indicating that the amount of these two phases is reduced with increasing Nb content, while the relative fraction of Nd 2 Fe 17 increases. The α-Fe grain size slightly decreases while that of the Nd 2 Fe 14 B phase is increasing, when the Nb content increases. The hysteresis loops indicate that these samples behave as hard ferromagnets, with a coercive field which decreases when the Nb content increases, but with rather low remanent magnetization.
Raebiger, James W.; Crawford, Charles A.; Zhou, Jian; Holm, R. H.
1997-03-12
The title clusters, several examples of which have been reported earlier, have been prepared by two different methods and subjected to structural and reactivity studies. The compounds (Et(4)N)(3)[(OC)(3)MFe(3)S(4)(Smes)(3)].MeCN (M = Mo/W) are isomorphous and crystallize in monoclinic space group P2(1)/n with a = 13.412(1)/13.297(1) Å, b = 19.0380(1)/18.9376(3) Å, c = 26.4210(1)/26.2949(1) Å, beta = 97.87(1)/97.549(1) degrees, and Z = 4. The clusters contain long M-S (2.62/2.59 Å) and M-Fe (3.22/3.19 Å) bonds, consistent with the reported structure of [(OC)(3)MoFe(3)S(4)(SEt)(3)](3-) (3). Reaction of [(OC)(3)MoFe(3)S(4)(LS(3))](3-) (7) with CO in the presence of NaPF(6) affords cuboidal [Fe(3)S(4)(LS(3))](3-) (9), also prepared in this laboratory by another route as a synthetic analogue of protein-bound [Fe(3)S(4)](0) clusters. The clusters [Fe(3)S(4)(SR)(3)](3-) (R = mes, Et), of limited stability, were generated by the same reaction. Treatment of 9 with [M(CO)(3)(MeCN)(3)] affords 7 and its M = W analogue. The clusters [(OC)(3)MFe(3)S(4)(SR)(3)](3-) form a four-member electron transfer series in which the 3- cluster can be once reduced (4-) and twice oxidized (2-, 1-) to afford clusters of the indicated charges. The correct assignment of redox couple to potential in the redox series of six clusters is presented, correcting an earlier misassignment of the redox series of 3. Carbonyl stretching frequencies are shown to be sensitive to cluster oxidation state, showing that the M sites and Fe(3)S(4) fragments are electronically coupled despite the long bond distances. (LS(3) = 1,3,5-tris((4,6-dimethyl-3-mercaptophenyl)thio)-2,4,6-tris(p-tolylthio)benzenate(3-); mes = mesityl.)
Powder alignment system for anisotropic bonded NdFeB Halbach cylinders \\ud
Zhu, Z.Q.; Xia, Z.P.; Atallah, K.; Jewell, G.W.; Howe, D.
2000-01-01
A Halbach cylinder, fabricated from pre-magnetized sintered NdFeB magnet segments, is proposed for the powder aligning system during the compression or injection moulding of anisotropic bonded Halbach oriented NdFeB ring magnets. The influence of leading design parameters of the powder aligning system, viz. the number of magnet segments per pole, their axial length and radial thickness, and their clearance from the mould, is investigated by finite element analysis, and validated experimentally
Exchange-coupled nanoscale SmCo/NdFeB hybrid magnets
Energy Technology Data Exchange (ETDEWEB)
Wang, Dapeng; Poudyal, Narayan; Rong, Chuanbing; Zhang, Ying; Kramer, Matthew J.; Liu, J. Ping
2012-05-11
Nanoscalehybridmagnets containing SmCo5 and Nd2Fe14B hard magnetic phases have been produced via a novel “in-one-pot” processing route. The grain size of the processed bulk composite materials is controlled below 20 nm. The refinement of the nanoscale morphology leads to effective inter-phase exchange coupling that results in single-phase like magnetic properties. Energy product of 14 MGOe was obtained in the isotropic nanocomposite magnets at room temperature. At elevated temperatures, the hybridmagnets have greatly improved thermal stability compared to the Nd2Fe14B single-phase counterpart and have substantially increased magnetization and energy products compared to the single-phase SmCo5 counterpart.
Directory of Open Access Journals (Sweden)
Tiburce A. Aboki
2013-04-01
Full Text Available Iron-boron based bulk metallic glasses (BMG development has been initiated using Fe40Ni38Mo4B18 as precursor. Addition of zirconium up to 10 atomic % along with the reduction of Ni proportion improves the glass forming ability (GFA, which is optimum when Ni is suppressed in the alloy. However melting instability occurred during the materials fabrication resulting in the formation of residual crystalline phases closely related to the amorphous phase. Microstructure study shows an evolution from amorphous structure to peculiar acicular structure, particularly for Fe50Ni16Mo6B18Zr10, suggesting the amorphous structure as interconnected atomic sheets like “atomic mille feuilles” whose growth affects the alloys’ GFA.
Temperature rise of the mask-resist assembly during LIGA exposure
International Nuclear Information System (INIS)
Ting, Aili
2004-01-01
Deep X-ray lithography on PMMA resist is used in the LIGA process. The resist is exposed to synchrotron X-rays through a patterned mask and then is developed in a liquid developer to make high aspect ratio microstructures. The limitations in dimensional accuracies of the LIGA generated microstructure originate from many sources, including synchrotron and X-ray physics, thermal and mechanical properties of mask and resist, and from the kinetics of the developer. This work addresses the thermal analysis and temperature rise of the mask-resist assembly during exposure in air at the Advanced Light Source (ALS) synchrotron. The concern is that dimensional errors generated at the mask and the resist due to thermal expansion will lower the accuracy of the lithography. We have developed a three-dimensional finite-element model of the mask and resist assembly that includes a mask with absorber, a resist with substrate, three metal holders, and a water-cooling block. We employed the LIGA exposure-development software LEX-D to calculate volumetric heat sources generated in the assembly by X-ray absorption and the commercial software ABAQUS to calculate heat transfer including thermal conduction inside the assembly, natural and forced convection, and thermal radiation. at assembly outer and/or inner surfaces. The calculations of assembly maximum temperature. have been compared with temperature measurements conducted at ALS. In some of these experiments, additional cooling of the assembly was produced by forced nitrogen flow ('nitrogen jets') directed at the mask surface. The temperature rise in the silicon mask and the mask holder comes directly from the X-ray absorption, but nitrogen jets carry away a significant portion of heat energy from the mask surface, while natural convection carries away negligibly small amounts energy from the holder. The temperature rise in PMMA resist is mainly from heat conducted from the silicon substrate backward to the resist and from the inner
Avaliação de Revestimentos de Liga de Níquel 625 Depositados pelo Processo Eletroescória
Sandes, Soraia Simões; Alvarães, Camila Pereira; Mendes, Matheus Campolina; Araújo, Leonardo Sales; Souza, Luis Felipe Guimarães de; Jorge, Jorge Carlos Ferreira
2017-01-01
Resumo A aplicação de revestimentos de ligas de níquel é comumente realizada na indústria de petróleo e gás para aumento da vida de equipamentos em ambientes agressivos, dado que este procedimento melhora a resistência à corrosão, sem um aumento significativo do custo de produção quando comparado com equipamentos maciços fabricados com outras ligas. Normalmente, as juntas são soldadas pelos processos de eletrodos revestidos, MIG/MAG ou TIG. Neste aspecto, o processo eletroescória realiza depo...
Energy Technology Data Exchange (ETDEWEB)
Rocha, M.O.A; Vidilli, A.L.; Afonso, C.R.M., E-mail: andre.vidilli@gmail.com [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil)
2014-07-01
The Ti-6Al-4V, widely used in biomaterials, exhibits elastic modulus (E) of approximately 110GPa, which is significantly higher than the one of human bone (E = 10 to 30 GPa). In this project, a process of rapid solidification was utilized in 4 different alloys of Ti-Mo-Fe-Sn, in order to produce ultrafine nanocrystalline eutectic alloys, which present high strength (1800-2500 MPa), low elastic modulus (50-110 GPa) and good corrosion resistance. The alloys Ti{sub 62}Fe{sub 30}Mo{sub 8}, Ti{sub 56}Fe{sub 30}Mo{sub 8}Sn{sub 6}, Ti{sub 63}Fe{sub 23}Mo{sub 8}Sn{sub 6}, Ti{sub 60}Fe{sub 23}Mo{sub 8}Sn{sub 9} show Vickers microhardness de, respectively, 745 (1mm), 733 (1mm), 609 (1mm) e 651(1mm) HV. The characterization was performed using scanning electron microscopy (SEM) and X- ray diffraction (XRD). The results indicated the presence of a β-Ti (bcc) matrix and the intermetallic TiFe and Ti{sub 3}Sn phases, and the microstructure were formed by dendrites, and eutectic constituents, which were present in the compositions Ti{sub 62}Fe{sub 30}Mo{sub 8}, Ti{sub 56}Fe{sub 30}Mo{sub 8}Sn{sub 6}, Ti{sub 63}Fe{sub 23}Mo{sub 8}Sn{sub 6}, Ti{sub 60}Fe{sub 23}Mo{sub 8}Sn{sub 9}. (author)
Exchange-coupled nanoscale SmCo/NdFeB hybrid magnets
Energy Technology Data Exchange (ETDEWEB)
Wang Dapeng; Poudyal, Narayan; Rong, Chuanbing [Department of Physics, University of Texas at Arlington, Arlington, TX 76019 (United States); Zhang Ying [Department of Physics, University of Texas at Arlington, Arlington, TX 76019 (United States); Materials Science and Engineering, Ames Laboratory, USDOE, Iowa State University, Ames, IA 50011 (United States); Kramer, M.J. [Materials Science and Engineering, Ames Laboratory, USDOE, Iowa State University, Ames, IA 50011 (United States); Liu, J. Ping, E-mail: pliu@uta.edu [Department of Physics, University of Texas at Arlington, Arlington, TX 76019 (United States)
2012-09-15
Nanoscale hybrid magnets containing SmCo{sub 5} and Nd{sub 2}Fe{sub 14}B hard magnetic phases have been produced via a novel 'in-one-pot' processing route. The grain size of the processed bulk composite materials is controlled below 20 nm. The refinement of the nanoscale morphology leads to effective inter-phase exchange coupling that results in single-phase like magnetic properties. Energy product of 14 MGOe was obtained in the isotropic nanocomposite magnets at room temperature. At elevated temperatures, the hybrid magnets have greatly improved thermal stability compared to the Nd{sub 2}Fe{sub 14}B single-phase counterpart and have substantially increased magnetization and energy products compared to the single-phase SmCo{sub 5} counterpart. - Highlights: Black-Right-Pointing-Pointer We realize interphase exchange coupling in nanoscale SmCo{sub 5}/Nd{sub 2}Fe{sub 14}B magnets. Black-Right-Pointing-Pointer We observe homogenously distributed two-phase grains with size smaller than 20 nm. Black-Right-Pointing-Pointer We observe a common Curie temperature in the hybrid magnet. Black-Right-Pointing-Pointer High-temperature magnetic properties of the hybrid magnets greatly improved. Black-Right-Pointing-Pointer Plastic deformation of composite materials leads to self-nanoscaling of grains.
Influence of Al-W-B Recycled Composite Material on the Properties of High Performance Concrete
Directory of Open Access Journals (Sweden)
Baronins Janis
2015-12-01
Full Text Available The aim of this study is to obtain high performance boron containing material with sufficient carrying capacity with increased porosity and lower density at the same time. The influence of the different concentrations of Al-W-B powder on the properties of the fresh and hardened HPC was investigated. In the concrete mix design, the allite containing White Portland cement CEM I 52,5 R, granite stone, sand, microsilica, on polycarboxylates based super plasticizer and Al-W-B powder were used. As a source of boron composite material (CM, previously grinded powder containing boron-tungsten fiber and aluminium matrix (CM Al-W-B was used. Grinding was used for processing of CM Al-W-B powder.
Pressure-induced preferential growth of nanocrystals in amorphous Nd9Fe85B6
International Nuclear Information System (INIS)
Wu Wei; Li Wei; Sun Hongyu; Li Hui; Zhang Xiangyi; Li Xiaohong; Liu Baoting
2008-01-01
Control over the growth and crystallographic orientation of nanocrystals in amorphous alloys is of particular importance for the development of advanced nanocrystalline materials. In the present study, Nd 2 Fe 14 B nanocrystals with a strong crystallographic texture along the [410] direction have been produced in Nd-lean amorphous Nd 9 Fe 85 B 6 under a high pressure of 6 GPa at 923 K. This is attributed to the high pressure inducing the preferential growth of Nd 2 Fe 14 B nanocrystals in the alloy. The present study demonstrates the potential application of high-pressure technology in controlling nanocrystalline orientation in amorphous alloys
Hard magnetic property and δM(H) plot for sintered NdFeB magnet
International Nuclear Information System (INIS)
Gao, R.W.; Zhang, D.H.; Li, W.; Li, X.M.; Zhang, J.C.
2000-01-01
The hard magnetic properties and the interactions between the grains for sintered Nd 16 Fe 73 Co 5 B 6 magnets are investigated by using δM(H) plot technique. The results show that the δM(H) plot of NdFeB sintered magnet can explain the effects of the microstructure (size, shape and orientation of the grains) and the intergrain interactions on the hard magnetic properties of the magnet. However, the value of δM(H) is positive when the applied field is not strong enough, which means that the common δM(H) plot theory is not completely consistent with the sintered NdFeB magnet
Directory of Open Access Journals (Sweden)
Adriana Paula Tirone
2005-06-01
Full Text Available OBJETIVO: Estudar os marcadores moleculares para os genes da cadeia pesada da beta-miosina cardíaca e da proteína-C de ligação à miosina em familiares de portadores de cardiomiopatia hipertrófica. MÉTODOS: Foram estudadas 12 famílias que realizaram anamnese, exame físico, eletrocardiograma, ecocardiograma e coleta de sangue para o estudo genético através da reação em cadeia da polimerasse. RESULTADOS: Dos 227 familiares 25% eram acometidos, sendo 51% do sexo masculino com idade média de 35±19 (2 a 95 anos. A análise genética mostrou ligação com o gene da b-miosina cardíaca em uma família e, em outra, ligação com o gene da proteína C de ligação à miosina. Em cinco famílias foram excluídas ligações com os dois genes; em duas, a ligação com o gene da proteína C de ligação à miosina, porém para o gene da b-miosina os resultados foram inconclusivos; em duas famílias os resultados foram inconclusivos para os dois genes e em uma foi excluída ligação para o gene da b-miosina mas ficou inconclusivo para o gene da proteína C de ligação à miosina. CONCLUSÃO: Em nosso meio, talvez predominem outros genes que não aqueles descritos na literatura, ou que existam outras diferenças genéticas relacionadas com a origem de nossa população e/ou fatores ambientais.OBJECTIVE: To study the molecular markers for the genes of the heavy chain of cardiac beta-myosin and the myosin binding protein C in relatives of carriers of hypertrophic cardiomyopathy. METHODS: Twelve families who had anamnesis, physical exam, electrocardiogram, echocardiogram and blood collection for the genetic study through the chain reaction of polymerase. RESULTS: From the 227 relatives, 25% were ill-taken, with 51% men, with an average age of 35±19 (2 to 95 years old. The genetic analysis showed a connection with the gene of the cardiac b-myosin in a family and, in another, a connection with the gene of the myosin-binding protein C. In five
An, Xiaoxin; Jin, Kunpeng; Abbas, Nadeem; Fang, Qiuli; Wang, Fang; Du, Juan; Xia, Weixing; Yan, Aru; Liu, J. Ping; Zhang, Jian
2017-11-01
Hard magnetic NdFeB submicro/nanoflakes were successfully prepared by surfactant-assisted ball milling at low temperature (SABMLT) by specially using 2-methyl pentane and trioctylamine (TOA) as solvent and surfactant, respectively. Influences of the amount of TOA and milling temperature on the crystal structure, morphology and magnetic performances of the as-prepared NdFeB powders were investigated systematically. There is significant difference on morphology between the NdFeB powders milled at room and low temperature. The NdFeB powders with flaky morphology could be obtained even with a small amount of TOA by SABMLT, which could not be achieved by surfactant-assisted ball milling at room temperature (SABMRT). The better crystallinity, better grain alignment, higher coercivity, larger saturation magnetization and remanence ratio were achieved in the samples prepared by SABMLT. Furthermore, the final NdFeB powders prepared by SABMLT possessed a lower amount of residual TOA than those prepared by SABMRT. It was demonstrated that SABMLT is a promising way to fabricate rare-earth-transition metal nanoflakes with high anisotropy for permanent magnetic materials. The effective method of preparing NdFeB flakes by lowering temperature will be also useful to fabricate flakes of other functional materials.
First-order-reversal-curve analysis of exchange-coupled SmCo/NdFeB nanocomposite alloys
Energy Technology Data Exchange (ETDEWEB)
Pan, Mingxiang; Zhang, Pengyue, E-mail: Zhang_pengyue@cjlu.edu.cn; Ge, Hongliang; Yu, Nengjun; Wu, Qiong
2014-06-01
Exchange-coupled SmCo{sub 5}/Nd{sub 2}Fe{sub 14}B nanocomposite magnets have been fabricated by ball milling of the micrometer sized SmCo{sub 5} and Nd{sub 2}Fe{sub 14}B powders. The influence of Nd{sub 2}Fe{sub 14}B content on the microstructure and magnetic properties of these hybrid alloys was investigated. The alloys that show strong intergrain exchange-coupling behavior with (BH){sub max}=2.95 MGOe was obtained when the two hard phases are well coupled. A first-order-reversal-curve (FORC) analysis was performed for both SmCo{sub 5} single-phase magnet and SmCo{sub 5}/Nd{sub 2}Fe{sub 14}B hybrid magnet; the FORC diagrams results show two major peaks for the hybrid magnets. In both cases, the magnetization reversal behaviors for these alloys were discussed in detail and are consistent with the results of δM plots. - Highlights: • Exchange-coupled SmCo{sub 5}/Nd{sub 2}Fe{sub 14}B nanocomposite magnets were studied. • Magnetization reversal behaviors of the hybrid magnet were discussed. • The FORCs analysis is taken to identify the optimal conditions for hybrid magnet.
Magnetic regimes in amorphous Ni--Fe--P--B alloys
International Nuclear Information System (INIS)
Durand, J.
1976-10-01
A complete substitution of iron for nickel was obtained by splat-cooling in amorphous alloys of composition (Ni/sub 100-y/Fe/sub y/) 79 P 13 B 8 . Results of high-field magnetization (up to 70 kOe), ac and dc low-field susceptibility, Curie temperature, and resistivity measurements over a temperature range of 1.7 to 300 0 K are reported. The Ni 79 P 13 B 8 alloy is not ferromagnetic, but the magnetization behavior as a function of field and temperature is typically that of alloys in the critical concentration range for ferromagnetism. The Fe 79 P 13 B 8 alloy is ferromagnetic with a Curie temperature T/sub c/ of 616 0 K. For y = 1 at. percent, the Fe atoms are magnetic. The variation of the moment per Fe atom as a function of y is discussed. When y is increased, the Ni atoms are likely to be polarized progressively and the moment per Ni atom would be roughly constant for y equal to or greater than 30 at. percent. Various magnetic behaviors were defined as a function of the Fe content. The value of T/sub c/ reaches a maximum for y similarly ordered 90 at. percent and extrapolates to zero for y similarly ordered 7 at. percent. Alloys within the range 1 equal to or less than y equal to or less than 10 at. percent did not exhibit well-defined Curie transition, but sharp maxima in low-field susceptibility measurements were observed at T/sub M/. The value of T/sub M/ is proportional to y for 1 equal to or less than y equal to or less than 4 at. percent, as in classical spin-glass regimes. For 4 less than y equal to or less than 10 at. percent, the variation of T/sub M/ as a function of y implies a more complicated type of magnetic ordering (micromagnetism or superparamagnetism). Homogeneous ferromagnetic ordering emerges only for y greater than 10 at. percent. Results of resistivity measurements are discussed in relation to the magnetic properties of different regimes in the magnetic phase diagram. 6 figures, 2 tables
NMR and Moessbauer studies of the amorphous system Fe79P/sub 21-x/B/sub x/
International Nuclear Information System (INIS)
Amamou, A.; Durand, J.
1977-05-01
Combined NMR, spin-echo and Moessbauer experiments have been performed to obtain hyperfine field distributions of the transition metal and metalloid elements in splat-cooled amorphous Fe 79 P 21 /sub -x/B/sub x/ alloys. These distributions are related to the local environments of the elements. The NMR signals are observed in the low frequency range 20-60 MHz and all the nuclei, i.e. Fe, P and B, may contribute to the spectral distribution. The resolution of the spectra into that due to Fe and (P + B) nuclei was made possible by using samples prepared with an Fe 56 isotope. The Fe distribution thus obtaned shows general agreement with the Moessbauer field distribution. From a careful analysis of the NMR data, the hyperfine field at the B nuclei in these amorphous alloys is found to range from 24 to 26 KG increasing with B content. An upper limit of 8 KG for the half-width is attributed to this distribution. The Moessbauer spectra of the Fe 57 nuclei resemble those for the crystalline Fe 75 P 25 /sub -x/B/sub x/ alloys. A fit of the spectra shows a field distribution which suggests the presence of structure. Such a structure may correspond to various Fe sites, also seen in the crystalline alloys. The distributions generally lie between about 160 and 330 KG, with a maximum at about 260 KG. These spectra do not show the presence of Fe nuclei with essentially zero hyperfine field as was obtained for amorphous Fe-Pd-P by Sharon et al. and for amorphous Fe-P by Logan et al. With increasing B content the center of gravity of the Fe distribution shifts to higher values. From a systematic study of the NMR lines and other considerations it is concluded that the P field distribution is broad and its hyperfine field is between 20 and 35 KG for the higher P concentration alloys
DEFF Research Database (Denmark)
Du, Yuqing; Pan, Genhua; Moate, Roy
2010-01-01
Bottom pinned exchange bias systems of IrMn/CoFe and IrMn/CoFeB on CoFe seed layers were studied. Enhanced exchange anisotropy has been observed for IrMn/CoFeB samples annealed at 350 °C. The ferromagnetic and antiferromagnetic layers of both samples are polycrystalline and textured {110} for the...
VTVH-MCD study of the Delta nifB Delta nifZ MoFe protein from Azotobacter vinelandii.
Cotton, Marcia S; Rupnik, Kresimir; Broach, Robyn B; Hu, Yilin; Fay, Aaron W; Ribbe, Markus W; Hales, Brian J
2009-04-08
NifZ is a member of a series of proteins associated with the maturation of the nitrogenase MoFe protein. An MCD spectroscopic study was undertaken on the Delta nifB Delta nifZ MoFe protein generated in the absence of both NifZ and NifB (deletion of NifB generates an apo-MoFe protein lacking the FeMo cofactor). Results presented here show that, in the absence of NifZ, only one of the two P-clusters of the MoFe protein is matured to the ultimate [8Fe-7S] structure. The other P-cluster site in the protein contains a [4Fe-4S] cluster pair, representing a P-cluster precursor that is electronically identical to the analogous clusters observed in the Delta nifH MoFe protein. These results suggest that the MoFe protein is synthesized in a stepwise fashion where NifZ is specifically required for the formation of the second P-cluster.
Directory of Open Access Journals (Sweden)
Marcelo del Castillo
2004-04-01
Full Text Available Las endocarditis causadas por hongos, (Candida en particular, requieren tratamiento médico-quirúrgico, siendo la anfotericina B la droga de elección. Caspofungina es una equinocandina con gran actividad sobre Candida y Aspergillus. Se presenta un paciente con una endocarditis por Candida tropicalis resistente a fluconazol tratado con caspofungina bajo un esquema de salvataje, luego de haber presentado efectos adversos por anfotericina B. El paciente tuvo respuesta microbiológica.Fungal endocarditis, in particular due to Candida species, requires medical and surgical treatment and amphotericin B is the drug of choice. Caspofungin is an echinocandin very effective against Candida and Aspergillus. We present a patient with Candida tropicalis endocarditis, fluconazol resistant, treated with caspofungin, on a compassional basis as a result of adverse effects with amphotericin B. The patient had a microbiological response.
International Nuclear Information System (INIS)
Abdollahi-Alibeik, Mohammad; Rezaeipoor-Anari, Ali
2016-01-01
Boron modified MCM-41 with magnetite core (Fe_3O_4@B-MCM-41) as a new magnetically recoverable heterogeneous catalyst was prepared and characterized by SEM, TEM, BET, XRD, VSM and FT-IR techniques. The catalytic activity of Fe_3O_4@B-MCM-41 was investigated in the four-component reaction of aldehyde, dimedone, active methylene compounds and ammonium acetate for the synthesis of polyhydroquinolines. According to optimization and characterization results the catalyst with Si:B:Fe_3O_4 mole composition of 40:4:1 has the best activity. The catalyst could be recovered easily by external magnet and has excellent reusability many times without significant decrease of activity. - Highlights: • Core–shell Fe_3O_4@MCM-41 nanoparticles modified by boron (Fe_3O_4@B-MCM-41). • Fe_3O_4@B-MCM-41 as reusable catalyst for the synthesis of polyhydroquinolines. • Characterization of Fe_3O_4@B-MCM-41 using SEM, TEM, BET, XRD and FT-IR techniques.
Energy Technology Data Exchange (ETDEWEB)
San-noo, Toshimasa; Toriyama, Tamotsu; Wakabayashi, Hidehiko; Iijima, Hiroshi [Musashi Inst. of Tech., Tokyo (Japan); Hayashi, Nobuyuki; Sakamoto, Isao
1997-03-01
Since amorphous alloys are generally highly resistant to irradiation and their critical radiation dose is an order of magnitude higher for Fe-B amorphous alloy than Mo-methods, these alloys are expected to become applicable as for fusion reactor materials. The authors investigated {alpha}-Fe crystallization in an amorphous alloy, Fe{sub 80}B{sub 20} using internal conversion electron Moessbauer spectroscopy. The amount of {alpha}-Fe component was found to increase by raising the He-irradiation dose. The target part was modified to enable He ion radiation at a lower temperature (below 400 K) by cooling with Peltier element. Fe{sub 80}B{sub 20} amorphous alloy was cooled to keep the temperature at 300 K and exposed to 40 keV He ion at 1-3 x 10{sup 8} ions/cm{sup 2}. The amount of {alpha}-Fe crystal in each sample was determined. The crystal formation was not observed for He ion radiation below 2 x 10{sup 18} ions/cm{sup 2}, but that at 3 x 10{sup 8} ions/ cm{sup 2} produced a new phase ({delta} +0.40 mm/sec, {Delta} = 0.89 mm/sec). The decrease in the radiation temperature from 430 to 300 K resulted to extremely repress the production of {alpha}-Fe crystal, suggesting that the crystallization induced by He-radiation cascade is highly depending on the radiation temperature. (M.N.)
Kim, K. M.; Kang, M. S.; Kwon, H. W.; Lee, J. G.; Yu, J. H.
2018-05-01
Feasibility of the electrophoresis deposition (EPD) technique for homogeneous and adhesive deposition of DyF3 particles on the Nd-Fe-B-type particles was studied, and coercivity enhancement in the diffusion-treated Nd-Fe-B-type particles deposited with DyF3 by EPD was investigated. HDDR-treated Nd12.5Fe80.6B6.4Ga0.3Nb0.2 particles were deposited with DyF3 particles by EPD. More homogeneous and adhesive deposition of DyF3 particles on the surface of Nd-Fe-B particles was made by the EPD with respect to conventional dip-coating, and this led to more active and homogeneous diffusion of Dy. More profound coercivity enhancement was achieved in the diffusion-treated Nd-Fe-B-type particles deposited with DyF3 by EPD compared to dip-coated particles.
Al-Khafaji, M. A.; Rainforth, W. M.; Gibbs, M. R. J.; Davies, H. A.; Bishop, J. E. L.
1998-09-01
Magnetic force microscopy (MFM) has been employed to image the magnetic structure in nanocrystalline melt spun ribbon samples of NdFeB alloys of three markedly different and contrasting compositions: Low-Nd (Nd 9.5Fe 84.5B 6) containing Nd 2Fe 14B and α-Fe phases, stoichiometric (Nd 11.8Fe 82.3B 5.9), and high-Nd (Nd 18Fe 76B 6) containing Nd 2Fe 14B and Nd-rich phases. It was found that the magnetic domain length scale is significantly larger than the mean Nd 2Fe 14B grain size (˜35 nm) in each case, although small changes in force gradient occurred down to ˜20 nm. However, both the domain length scale and the tip-sample interaction `strength' were found to decrease with increasing Nd-content. An interpretation of these results in terms of the microstructure is given.
Wear behavior of the surface alloyed AISI 1020 steel with Fe-Nb-B by TIG welding technique
Energy Technology Data Exchange (ETDEWEB)
Kilinc, B., E-mail: bkilinc@sakarya.edu.tr; Durmaz, M.; Abakay, E. [Department of Metallurgical and Materials Engineering, Institute of Arts and Sciences, SakaryaUniversity, Esentepe Campus, 54187Sakarya (Turkey); Sen, U.; Sen, S. [Department of Metallurgical and Materials Engineering, Engineering Faculty, Sakarya University, Esentepe Campus, 54187 Sakarya (Turkey)
2015-03-30
Weld overlay coatings also known as hardfacing is a method which involves melting of the alloys and solidification for applied coatings. Recently hardfacing by welding has become a commonly used technique for improvement of material performance in extreme (high temperature, impact/abrasion, erosion, etc.) conditions.In the present study, the coatings were produced from a mixture of ferrous niobium, ferrous boron and iron powders in the ranges of -45µm particle size with different ratio. Fe{sub 12}Nb{sub 5}B{sub 3} and Fe{sub 2}NbBalloys were coated on the AISI 1020 steel surface by TIG welding. The phases formed in the coated layer are Fe{sub 2}B, NbB{sub 2}, NbFeB and Fe0,2 Nb{sub 0,8} phases. The hardness of the presence phases are changing between 1689±85 HV{sub 0.01}, and 181±7 HV{sub 0.1}. Microstructural examinations were realized by optical and scanning electron microscopy. The wear and friction behaviors of Fe{sub 12}Nb{sub 5}B{sub 3} and Fe2NbB realized on the AISI 1020 steel were investigated by the technique of TIG welding by using ball-on-disk arrangement against alumina ball.
1000 kW ICRH amplifiers for MFTF-B
International Nuclear Information System (INIS)
Boksberger, U.
1986-01-01
For the startup of the MFTF-B ICRH heating will be applied. Two commercial amplifiers derived from standard broadcast transmitters provide 1000 kW RF power each into a matching system for any VSWR as high as 1.5. Emphasis is put on the specific environment of magnetic fields and seismic loads as well as to the particular RF power control requirements and remote operation. Also addressed is the amplifier's performance into a typical load. The load variations due to the MFTF-B plasma coupling were calculated by TRW
Vieira, Ana Rita Ribeiro
2013-01-01
Dissertação para obtenção do Grau de Mestre em Engenharia Civil - Ramo de Estruturas e Geotecnia Nesta dissertação avalia-se a capacidade resistente última de estacas em compressão usando análises em tensão/deformação. A capacidade resistente última das estacas é avaliada através do programa computacional de elementos finitos Plaxis 2D v. 8 e é comparada com a capacidade resistente última prevista por métodos de extrapolação da curva carga vs. assetamento de ensaios de carga que não ...
Directory of Open Access Journals (Sweden)
Emilce de los A Méndez
2012-12-01
Full Text Available Community-acquired methicillin-resistant Staphylococcus aureus (CA-MRSA is increasingly recognized as an important pathogen causing skin and soft tissue infections as well as necrotizing pneumonia. We describe a case of familial transmission of CA-MRSA between a 6-month-old boy and his mother in Santa Fe City, Argentina. Both isolates showed an identical antimicrobial susceptibility profile, carried type IV SCCmec and harboured the pvl and the lnu(A genes. Isolates showed indistinguishable SmaI-PFGE patterns confirming their genetic relationship. These results corroborate the intrafamilial transmission of CA-MRSA and might associate this strain with the repetitive events of furunculosis within the family.Staphylococcus aureus resistente a la meticilina adquirido en la comunidad (SARM-AC es reconocido como un patógeno importante que causa infecciones de piel y partes blandas y neumonía necrotizante. Describimos un caso de transmisión familiar de SARM-AC entre un nino de 6 meses de edad y su madre en la ciudad de Santa Fe, Argentina. Ambos aislamientos mostraron idéntico perfil de sensibilidad a los antimicrobianos, tenían el SCCmec tipo IV, y contenían los genes pvl y lnu(A. Los aislamientos presentaron patrones de SmaI-PFGE indistinguibles entre sí, lo cual confirmó su relación genética. Estos resultados corroboran la transmisión intrafamiliar de SARM-AC; asimismo, este aislamiento podría asociarse con los eventos repetitivos de furunculosis en la familia.
Importance of tests for the complete Lorentz structure of the t→W+b vertex at hadron colliders
International Nuclear Information System (INIS)
Nelson, C.A.; Kress, B.T.; Lopes, M.; McCauley, T.P.
1998-01-01
In a separate paper, the most general Lorentz-invariant decay-density matrix for t→W + b→(l + ν)b, or for t→W + b→(j bar d j u )b, is expressed in terms of eight helicity parameters. The parameters can be used to test for a variety of sources of new physics in t→W + b decay. By stage-two spin-correlation techniques, percent level statistical uncertainties are typical for W-polarimetry measurements of these helicity parameters at the Fermilab Tevatron, and several mill level uncertainties are typical for W-polarimetry measurements at the CERN LHC. Λ b polarimetry could be used to measure the relative phase of the b L and b R amplitudes. copyright 1998 The American Physical Society
Energy Technology Data Exchange (ETDEWEB)
Ivanov, S.A. [Center of Materials Science, Karpov' Institute of Physical Chemistry, Vorontsovo Pole 10, Moscow, 105064 (Russian Federation); Department of Engineering Sciences, Uppsala University, Box 534, 751 21, Uppsala (Sweden); Bush, A.A. [Moscow State University of Information Technologies, RadioEngineering and Electronics, pr.Vernadskogo 78, Moscow, 119454 (Russian Federation); Ritter, C. [Institute Laue-Langevin, BP 156, F-38042, Grenoble (France); Behtin, M.A. [Moscow State University of Information Technologies, RadioEngineering and Electronics, pr.Vernadskogo 78, Moscow, 119454 (Russian Federation); Cherepanov, V.M. [National Research Centre Kurchatov Institute, pl. Kurchatova 1, Moscow, 123182 (Russian Federation); Autieri, C.; Kvashnin, Y.O.; Di Marco, I.; Sanyal, B.; Eriksson, O. [Department of Physics and Astronomy, Uppsala University, Box 516, 751 20, Uppsala (Sweden); Kumar, P. Anil; Nordblad, P. [Department of Engineering Sciences, Uppsala University, Box 534, 751 21, Uppsala (Sweden); Mathieu, R., E-mail: roland.mathieu@angstrom.uu.se [Department of Engineering Sciences, Uppsala University, Box 534, 751 21, Uppsala (Sweden)
2017-02-01
The perovskite system Pb(Fe{sub 1-x}Mn{sub x}){sub 2/3}W{sub 1/3}O{sub 3} (0 ≤ x ≤ 1, PFMWO) has been prepared by conventional solid-state reaction under different sintering conditions. Structures and phase composition as well as thermal, magnetic and dielectric properties of the compounds have been systematically investigated experimentally and by first-principles density functional calculations. A clean perovskite phase is established at room temperature for compositions 0 ≤ x ≤ 0.4. Rietveld refinements of X-ray and neutron powder diffraction patterns demonstrate that the compounds crystallize in space group Pm-3m (0 ≤ x ≤ 0.4). The degree of ordering of the Fe and W/Mn cations was found to depend on the concentration of Mn. First-principles calculations suggest that the structural properties of PFMWO are strongly influenced by the Jahn-Teller effect. The PFMWO compounds behave as relaxor ferroelectrics at weak Mn-doping with a dielectric constant that rapidly decreases with increasing Mn content. A low temperature antiferromagnetic G-type order with propagation vector k = (1/2,1/2,1/2) is derived from neutron powder diffraction data for the samples with x ≤ 0.4. However with increasing doping concentration, the magnetic order is perturbed. First-principles calculations show that the dominant exchange coupling is antiferromagnetic and occurs between nearest neighbor Fe atoms. When the system is doped with Mn, a relatively weak ferromagnetic (FM) interaction between Fe and Mn atoms emerges. However, due to the presence of this FM interaction, the correlation length of the magnetic order is greatly shortened already at rather low doping levels. - Highlights: • The perovskite system Pb(Fe{sub 1−x}Mn{sub x}){sub 2/3}W{sub 1/3}O{sub 3} (0 ≤ x ≤ 1, PFMWO) has been synthesized. • The structural, magnetic, and dielectric properties of PFMWO have been investigated. • The degree of ordering of the Fe and W/Mn cations was found to depend on x.
Energy Technology Data Exchange (ETDEWEB)
Rodrigues, Daniel; Beneduce Neto, Flavio; Landgraf, Fernando Jose Gomes; Neiva, Augusto Camara; Romero, Sergio; Missell, Frank Patrick
1993-12-31
Results are presented on magnetic properties of Nd-Fe-B sauntered magnets produced from 1 kg of alloy caste in vacuum induction furnace. The fabrication viability of these magnets, with properties similar to the commercial magnets, and the influence of particle size in the energy product, through the effect on the H{sub k} field, is confirmed 12 refs., 7 figs., 1 tab.
Laser cladding of in situ TiB2/Fe composite coating on steel
International Nuclear Information System (INIS)
Du Baoshuai; Zou Zengda; Wang Xinhong; Qu Shiyao
2008-01-01
To enhance the wear resistance of mechanical components, laser cladding has been applied to deposit in situ TiB 2 /Fe composite coating on steel using ferrotitanium and ferroboron as the coating precursor. The phase constituents and microstructure of the composite coating were investigated using X-ray diffraction (XRD), scanning electron micrograph (SEM) and electron probe microanalysis (EPMA). Microhardness tester and block-on-ring wear tester were employed to measure the microhardness and dry-sliding wear resistance of the composite coating. Results show that defect-free composite coating with metallurgical joint to the steel substrate can be obtained. Phases presented in the coating consist of TiB 2 and α-Fe. TiB 2 particles which are formed in situ via nucleation-growth mechanism are distributed uniformly in the α-Fe matrix with blocky morphology. The microhardness and wear properties of the composite coating improved significantly in comparison to the as-received steel substrate due to the presence of the hard reinforcement TiB 2
Hayakawa, Y.; Makino, A.; Inoue, A.; Masumoto, T.
1996-01-01
In Fe-M-(B and/or O)(M=group IV A, V A elements) alloy films, nanocrystalline bcc phase are formed by annealing the amorphous single phase for Fe-M-B films, whereas the bcc nanocrystals are already formed in an as-deposited state for Fe-M-O or Fe-M-B-O) films. Among Fe-M-B films with various M elements, Fe-(Zr, Hf, Nb, Ta)-B alloy films exhibit high saturation magnetization (Is) above 1.4 T and high relative permeability (|μ|) above 1000 at 1MHz. The highest |μ| of 3460 at 1MHz is obtained fo...
Transport properties and exponential n-values of Fe/MgB2 tapes with various MgB2 particle sizes
International Nuclear Information System (INIS)
Lezza, P.; Abaecherli, V.; Clayton, N.; Senatore, C.; Uglietti, D.; Suo, H.L.; Fluekiger, R.
2004-01-01
Fe/MgB 2 tapes have been prepared starting with pre-reacted binary MgB 2 powders. As shown by resistive and inductive measurements, the reduction of particle size to a few microns by ball milling has little influence on B c2 , while the superconducting properties of the individual MgB 2 grains are essentially unchanged. Reducing the particle size causes an enhancement of B irr from 14 to 16 T, while J c has considerably increased at high fields, its slope J c (B) being reduced. At 4.2 K, values of 5.3 x 10 4 and 1.2 x 10 3 A/cm 2 were measured at 3.5 and 10 T, respectively, suggesting a dominant role of the conditions at the grain interfaces. A systematic variation of these conditions at the interfaces is undertaken in order to determine the limit of transport properties for Fe/MgB 2 tapes. The addition of 5% Mg to MgB 2 powder was found to affect neither J c nor B c2 . For the tapes with the highest J c values, very high exponential n factors were measured: n=148, 89 and 17 at 3.5, 5 and 10 T, respectively and measurements of critical current versus applied strain have been performed. The mechanism leading to high transport critical current densities of filamentary Fe/MgB 2 tapes based on MgB 2 particles is discussed
Effects of buffer layer temperature on the magnetic properties of NdFeB thin film magnets
International Nuclear Information System (INIS)
Kim, Y.B.; Cho, S.H.; Kim, H.T.; Ryu, K.S.; Lee, S.H.; Lee, K.H.; Kapustin, G.A.
2004-01-01
Effects of the buffer layer temperature (T b ) on the magnetic properties and microstructure of [Mo/NdFeB/Mo]-type thin films have been investigated. The Mo-buffer layer with low T b is composed of fine grains while that with high T b has coarse grains. The subsequent NdFeB layer also grows with fine or coarse grains following the buffer layer structure. The NdFeB layer grown on a low T b buffer shows high coercivity and strong perpendicular anisotropy. The best magnetic properties of i H c =1.01 MA/m (12.7 kOe), B r =1.31 T (13.1 kG) and BH max =329 kJ/m 3 (41.4 MGOe) were obtained from the film with T b =400 deg. C
Surface characterization of amorphous and crystallized Fe 80B 20
Huntley, D. R.; Overbury, S. H.; Zehner, D. M.; Budai, J. D.; Brower, W. E.
1986-11-01
Recent studies of catalysis by amorphous metals have prompted an interest in their surface properties. We have utilized Auger electron spectroscopy, X-ray photoelectron spectroscopy and low energy alkali ion scattering to study the surface composition, electronic properties and topography of amorphous and crystallized Fe 80B 20 ribbons. The majorresults are that the surface stoichiometry is approximately that of the bulk, unaltered by segregation. Bulk crystallization results in the diffusion of impurities to the surface, but does not change the Fe/B ratio. A small shift in the B1s core level binding energy was observed on crystalline, annealed surfaces relative to amorphous or sputtered surfaces, but no shifts were observed in the iron core level energies. A weak feature due to the B2p levels was observed in the valence band spectra from sputtered surfaces. The surfaces exhibit atomic scale roughness which is not altered by bulk crystallization. Finally, there were no observable differences in the structure, composition or electronic properties between the two sides of the ribbons.
International Nuclear Information System (INIS)
Yim, H.I.; Lee, S.Y.; Hwang, J.Y.; Rhee, J.R.; Chun, B.S.; Wang, K.L.; Kim, Y.K.; Kim, T.W.; Lee, S.S.; Hwang, D.G.
2008-01-01
Double-barrier magnetic tunnel junctions (DMTJs) with and without an amorphous ferromagnetic material such as CoFeSiB 10, CoFe 5/CoFeSiB 5, and CoFe 10 (nm) were prepared and compared to investigate the bias voltage dependence of the tunneling magnetoresistance (TMR) ratio. Typical DMTJ structures were Ta 45/Ru 9.5/IrMn 10/CoFe 7/AlO x /free layer 10/AlO x /CoFe 7/IrMn 10/Ru 60 (in nanometers). The interlayer coupling field and the normalized TMR ratios at the applied voltages of +0.4 and -0.4 V of the amorphous CoFeSiB free-layer DMTJ offer lower and higher values than that of the polycrystalline CoFe free-layer DMTJ, respectively. An amorphous ferromagnetic CoFeSiB layer improves the interface roughness of the free layer/tunnel barrier and, as a result, the interlayer coupling field and bias voltage dependence of the TMR ratio are suppressed at a given voltage. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)
Abreu, F.; Sabariz, A.; Quadro, A.; Bueno, A.
2012-01-01
Atualmente, as ligas de alumínio da série 6xxx vêm ocupando um espaço importante na produção global das ligas de alumínio. A utilização em larga escala dessa classe de ligas é consequência da melhoria de suas propriedades mecânicas quando submetidas a tratamentos térmicos. No entanto, a realização de tratamentos térmicos de solubilização e a precipitação de fases metaestáveis durante o envelhecimento podem prejudicar consideravelmente a resistência à corrosão dessa classe de ligas. O presente...
Directory of Open Access Journals (Sweden)
K. M. Kim
2018-05-01
Full Text Available Feasibility of the electrophoresis deposition (EPD technique for homogeneous and adhesive deposition of DyF3 particles on the Nd-Fe-B-type particles was studied, and coercivity enhancement in the diffusion-treated Nd-Fe-B-type particles deposited with DyF3 by EPD was investigated. HDDR-treated Nd12.5Fe80.6B6.4Ga0.3Nb0.2 particles were deposited with DyF3 particles by EPD. More homogeneous and adhesive deposition of DyF3 particles on the surface of Nd-Fe-B particles was made by the EPD with respect to conventional dip-coating, and this led to more active and homogeneous diffusion of Dy. More profound coercivity enhancement was achieved in the diffusion-treated Nd-Fe-B-type particles deposited with DyF3 by EPD compared to dip-coated particles.
Segregation of H, C and B to Σ = 5 (0 1 3) α-Fe grain boundary: A theoretical study
International Nuclear Information System (INIS)
Gesari, S.; Irigoyen, B.; Juan, A.
2006-01-01
The ASED-MO theory is used to study the effects of H and the H-C and H-B pairs in the electronic structure of a Fe grain boundary (GB). The results obtained for H in a GB model are consistent with its behavior as a chemical embrittler. The total energies calculated for FeH, FeC and FeB clusters indicate that all interstitials segregate to the GB. C has the lowest energy, followed by B, and could compete with other impurities for the site location on the GB. The results obtained for FeCH and FeBH are consistent with the observed behavior of C and B as cohesion enhancers. A strong repulsive interaction between C and H and B and H atoms is developed if they occupy the nearest interstitial site on the GB. When C or B are present, the total energies are similar to that obtained for the FeH cluster. This indicates that H is displaced from the capped trigonal prism (CTP). Also, we do not detect any C-H or B-H interaction. Density of states (DOS) and crystal orbital overlap population (COOP) curves are used to shed more light on the interstitial-Fe GB interaction. The existence of strong metal-metalloid bonds is shown, which are primarily due to Fe 3d, 4s and C (or B) 2s, 2p interactions
Directory of Open Access Journals (Sweden)
Y.-Z. Ma
2008-01-01
Full Text Available (W,Ni,Fe composite oxide powder synthesized by spray drying was reduced at 700∘C for 90 minutes in H2 atmosphere. The effect of rare earth Y on H2 reduction of (W,Ni,Fe composite oxide powder was studied. Phase composition, crystalline size, and particle morphology of the reduced powder have been measured by X-ray diffraction and scanning electron microscope (SEM. Fsss particle size and special surface area of the reduced powder were also measured and analyzed. The result showed that new phase Y(Ni0.75W0.25O3 appeared in the reduced powder and particle morphology was nearly spherical or polyhedron by Y additions. The higher the rare earth element content was, the bigger the influencing on particle morphology was. When the rare earth Y content was under 0.8%, with the increase of the rare earth element content, dBET, Fsss, and crystal sizes of the reduced powder decreased greatly.
Energy Technology Data Exchange (ETDEWEB)
Zhang, Pengjie [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Earth-Panda Advance Magnetic Material Co. Ltd., Hefei (China); Anhui Province Key Laboratory of Rare Earth Permanent Magnet Materials, Hefei (China); State Key Laboratory of Rare Earth Permanent Magnet Materials (Earth-Panda Advance Magnetic Material Co., Ltd.), Hefei (China); Xu, Guangqing, E-mail: gqxu1979@hfut.edu.cn [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Liu, Jiaqin [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Yi, Xiaofei [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Earth-Panda Advance Magnetic Material Co. Ltd., Hefei (China); Anhui Province Key Laboratory of Rare Earth Permanent Magnet Materials, Hefei (China); State Key Laboratory of Rare Earth Permanent Magnet Materials (Earth-Panda Advance Magnetic Material Co., Ltd.), Hefei (China); Wu, Yucheng, E-mail: ycwu@hfut.edu.cn [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Chen, JingWu [Earth-Panda Advance Magnetic Material Co. Ltd., Hefei (China); Anhui Province Key Laboratory of Rare Earth Permanent Magnet Materials, Hefei (China); State Key Laboratory of Rare Earth Permanent Magnet Materials (Earth-Panda Advance Magnetic Material Co., Ltd.), Hefei (China)
2016-02-15
Graphical abstract: Zn coated NdFeB specimens pretreated with different technologies possess different adhesive strengths and anticorrosion properties. And the combined technology of sandblasting and pickling (5 s) achieves the best comprehensive performance. - Highlights: • Zn coated NdFeB specimens are achieved with different pretreating technologies. • Combined technology possesses the highest adhesive strength. • Combined technology possesses excellent anticorrosion property. - Abstract: Zinc coated NdFeB specimens were prepared with different pretreating technologies, such as polishing, pickling (50 s), sandblasting and combined technology of sandblasting and pickling (5 s). Morphologies of the NdFeB substrates pretreated with different technologies were observed with a scanning electron microscope equipped with an energy dispersive spectrometer and an atomic force microscope. The tensile test was performed to measure the adhesive strength between Zn coating and NdFeB substrate. The self-corrosion behavior of the NdFeB specimen was characterized by potentiodynamic polarization curve. The anticorrosion properties of Zn coated NdFeB specimens were characterized by neutral salt spray tests. The pretreating technologies possess obvious impact on the adhesive strength and anticorrosion property of Zn coated NdFeB specimens. Combined pretreating technology of sandblasting and pickling (5 s) achieves the highest adhesive strength (25.56 MPa) and excellent anticorrosion property (average corrosion current density of 21 μA/cm{sup 2}) in the four pretreating technologies. The impacting mechanisms of the pretreating technology on the adhesive strength and anticorrosion properties are deeply discussed.
International Nuclear Information System (INIS)
Zhang, Pengjie; Xu, Guangqing; Liu, Jiaqin; Yi, Xiaofei; Wu, Yucheng; Chen, JingWu
2016-01-01
Graphical abstract: Zn coated NdFeB specimens pretreated with different technologies possess different adhesive strengths and anticorrosion properties. And the combined technology of sandblasting and pickling (5 s) achieves the best comprehensive performance. - Highlights: • Zn coated NdFeB specimens are achieved with different pretreating technologies. • Combined technology possesses the highest adhesive strength. • Combined technology possesses excellent anticorrosion property. - Abstract: Zinc coated NdFeB specimens were prepared with different pretreating technologies, such as polishing, pickling (50 s), sandblasting and combined technology of sandblasting and pickling (5 s). Morphologies of the NdFeB substrates pretreated with different technologies were observed with a scanning electron microscope equipped with an energy dispersive spectrometer and an atomic force microscope. The tensile test was performed to measure the adhesive strength between Zn coating and NdFeB substrate. The self-corrosion behavior of the NdFeB specimen was characterized by potentiodynamic polarization curve. The anticorrosion properties of Zn coated NdFeB specimens were characterized by neutral salt spray tests. The pretreating technologies possess obvious impact on the adhesive strength and anticorrosion property of Zn coated NdFeB specimens. Combined pretreating technology of sandblasting and pickling (5 s) achieves the highest adhesive strength (25.56 MPa) and excellent anticorrosion property (average corrosion current density of 21 μA/cm 2 ) in the four pretreating technologies. The impacting mechanisms of the pretreating technology on the adhesive strength and anticorrosion properties are deeply discussed.
NNLO QCD corrections to associated W H production and H →b b ¯ decay
Caola, Fabrizio; Luisoni, Gionata; Melnikov, Kirill; Röntsch, Raoul
2018-04-01
We present a computation of the next-to-next-to-leading-order (NNLO) QCD corrections to the production of a Higgs boson in association with a W boson at the LHC and the subsequent decay of the Higgs boson into a b b ¯ pair, treating the b quarks as massless. We consider various kinematic distributions and find significant corrections to observables that resolve the Higgs decay products. We also find that a cut on the transverse momentum of the W boson, important for experimental analyses, may have a significant impact on kinematic distributions and radiative corrections. We show that some of these effects can be adequately described by simulating QCD radiation in Higgs boson decays to b quarks using parton showers. We also describe contributions to Higgs decay to a b b ¯ pair that first appear at NNLO and that were not considered in previous fully differential computations. The calculation of NNLO QCD corrections to production and decay sub-processes is carried out within the nested soft-collinear subtraction scheme presented by some of us earlier this year. We demonstrate that this subtraction scheme performs very well, allowing a computation of the coefficient of the second-order QCD corrections at the level of a few per mill.
Rao, G. V. S. Jayapala; Prasad, T. N. V. K. V.; Shameer, Syed; Rao, M. Purnachandra
2018-04-01
Neodymium iron boron (NdFeB) permanent magnets have high energy product with suitable magnetic and physical properties for an array of applications including power generation and motors. However, synthetic routes of NdFeB permanent magnets involve critical procedures with high energy and needs scientific skills. Herein, we report on soapnut extract mediated synthesis of nanoscale cobalt substituted NdFeB (Co-NdFeB) permanent magnetic powders (Nd: 15%, Fe: 77.5%, B: 7.5% and Co with molar ratios: 0.5, 1, 1.5 and 2). A 10 ml of 10% soapnut extract was added to 90 ml of respective chemical composition and heated to 60 °C for 30 min and aged for 24 h. The dried powder was sintered at 500 °C for 1 h. The characterization of the prepared nanoscale Co-NdFeB magnetic powders was done using the techniques such as Dynamic Light Scattering (DLS for size and zeta potential measurements), X-ray diffraction (XRD) for structural determination, Scanning electron microscopy (SEM) with energy dispersion spectroscopy (EDS) for surface morphological and elemental analysis, Fourier transform infrared spectroscopy (FT-IR) for the identification of functional groups associated and hysteresis loop studies to quantify the magnetization. The results revealed that particles were in irregular and tubular shaped and highly stable (Zeta potential: -44.4 mV) with measured size <100 nm. XRD micrographs revealed a tetragonal crystal structure and FTIR showed predominant N-H and O-H stretching indicates the involvement of these functional groups in the reduction and stabilization process of Co-NdFeB magnetic powders. Hysteresis studies signify the effect of an increase in Co concentration.
International Nuclear Information System (INIS)
He, Shu-li; Zhang, Hong-wei; Rong, Chuan-bing; Chen, Juan; Sun, Ji-rong; Shen, Bao-gen
2012-01-01
Demagnetization curves for nanocomposite Pr 2 Fe 14 B/α-Fe permanent magnets with different hard grain alignment are calculated by a micromagnetic finite-element method. The results show that both remanence and coercivity increase with improving hard grains alignment. The demagnetization curves show a single-phase demagnetization behavior for the samples with grain size d of 10 nm and two-phase behavior for the samples with d of 20 and 30 nm. H ex (reflecting the magnetic hardening of α-Fe) and H irr (expressing the irreversible reversal of hard phase) are both enhanced with improving the hard grain alignment. The magnetic reversal in orientated nanocomposite permanent magnets is mainly controlled by inhomogeneous pinning of the nucleated type. - Highlights: ► The magnetic properties of nanocomposite Pr 2 Fe 14 B/α-Fe permanent magnets with different hard grains alignment are investigated by micromagnetic finite-element method. ► The calculated results show that both remanence and coercivity increase with improving hard grains alignment. ► Highly ordered orientation of hard phase is the critical factor to improve the properties of nanocomposites.
Li, Jianqiang; Lu, Caijiang; Xu, Changbao; Zhong, Ming
2015-09-01
This paper develops a simple miniature magnetoelectric (ME) laminate FeCuNbSiB/PZT-stack made up of magnetostrictive Fe73.5Cu1Nb3Si13.5B9 (FeCuNbSiB) foils and piezoelectric Pb(Zr, Ti)O3 (PZT) multilayer stack vibrator. Resonant ME interactions of FeCuNbSiB/PZT-stack with different layers of FeCuNbSiB foil (L) are investigated in detail. The experimental results show that the ME voltage coefficient reaches maximum value of 141.5 (V/cm Oe) for FeCuNbSiB/PZT-stack with L = 6. The AC-magnetic sensitivities can reach 524.29 mV/Oe and 1.8 mV/Oe under resonance 91.6 kHz and off-resonance 1 kHz, respectively. The FeCuNbSiB/PZT-stack can distinguish small dc-magnetic field of ˜9 nT. The results indicate that the proposed ME composites are very promising for the cheap room-temperature magnetic field sensing technology.
The microstructure and magnetic properties of melt-spun Fe 76Nd 16B 8 magnetic materials
Hadjipanayis, G. C.; Dickenson, R. C.; Lawless, K. R.
1986-02-01
The origin of magnetic hardening has been examined in melt-spun Fe 76Nd 16B 8 samples heat-treated at around 700°C. Microstructure studies show the same phases as in sintered magnets consisting of Fe 14Nd 2B, Fe 4NdB 4 and two high-Nd content phases. These phases exist in both equiaxed and faceted crystallites of submicron size. Lorentz microscopy shows domain walls which end at grain boundaries indicating that they are pinned there.
Westendorf effect in the magnet alloy Nd-Dy-Fe-Co-B
International Nuclear Information System (INIS)
Piskorskij, V.P.; Valeev, R.A.; Sychev, I.V.
2006-01-01
Sintered magnets of the composition as follows, at. %: (Nd 0.6 Dy 0.4 ) 15 (Fe 1-x Co x ) rest Al 1 B 8 , are under study. It is revealed that the course of coercive force dependence on the temperature of heat treatment varies with a cobalt content increase (within a range of 0.19 - 0.26). The dependence of coercive force on heat treatment temperature for the alloys studied has a pronounced minimum at 700 deg C which is known as a Westendorf effect. This effect is taken to be due to the presence of R(Fe, Co) 4 B phase where R is the sum of REM [ru
Coatings synthesised by the pulsed laser ablation of a B{sub 4}C/W{sub 2}B{sub 5} ceramic composite
Energy Technology Data Exchange (ETDEWEB)
Tadadjeu Sokeng, I., E-mail: ifriky@tlabs.ac.za [Department of Electrical, Electronics and Computer Engineering, French South African Institute of Technology/Cape Peninsula University of Technology, Bellville campus, PO Box 1906, Bellville, 7530 (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, 7129, PO Box 722, Somerset West, Western Cape Province (South Africa); UNESCO-UNISA Africa Chair in Nanosciences/Nanotechnology, College of Graduate Studies, University of South Africa (UNISA), Muckleneuk Ridge, PO Box 392, Pretoria (South Africa); Ngom, B.D. [Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, 7129, PO Box 722, Somerset West, Western Cape Province (South Africa); UNESCO-UNISA Africa Chair in Nanosciences/Nanotechnology, College of Graduate Studies, University of South Africa (UNISA), Muckleneuk Ridge, PO Box 392, Pretoria (South Africa); Laboratoire de Photonique et de Nanofrabrication, Groupes de physique du Solide et Sciences des Matriaux (GPSSM), Facult des sciences et Techniques Universit Cheikh Anta Diop de Dakar (UCAD), B.P. 25114 Dakar, Fann Dakar (Senegal); Msimanga, M. [iThemba LABS Gauten, Private Bag 11, WITS 2050 Johannesburg (South Africa); Nuru, Z.Y.; Kotsedi, L.; Maaza, M. [Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, 7129, PO Box 722, Somerset West, Western Cape Province (South Africa); UNESCO-UNISA Africa Chair in Nanosciences/Nanotechnology, College of Graduate Studies, University of South Africa (UNISA), Muckleneuk Ridge, PO Box 392, Pretoria (South Africa); Van Zyl, R.R. [Department of Electrical, Electronics and Computer Engineering, French South African Institute of Technology/Cape Peninsula University of Technology, Bellville campus, PO Box 1906, Bellville, 7530 (South Africa)
2015-10-30
A pellet of B{sub 4}C/W{sub 2}B{sub 5} ceramic composite was characterised and subjected to pulsed laser ablation for the deposition of coatings on corning glass substrates. We reports an attempt to produce coatings from B{sub 4}C/W{sub 2}B{sub 5} by pulsed laser deposition (PLD). The thermal, electric and mechanical properties of B{sub 4}C/W{sub 2}B{sub 5} suggest that coatings synthesised from this composite can be used for space applications. The samples were characterised using X-ray Diffraction, Atomic Force Microscopy and Heavy Ion Elastic Recoil Detection Analysis. The characterisation of the samples deposited on soda lime corning glass showed that the laser energy used in this PLD was enough to obtain non amorphous coatings formed by some alteration of the tungsten carbide crystal lattice at room temperature, and that there was no stoichiometry transfer as would be expected from PLD. The coating also showed space applicable features worth investigating. - Highlights: • B{sub 4}C/W{sub 2}B{sub 5} ceramic composite was ablated for deposition on corning glass subtrates. • Non-amorphous coating was obtained at room temperature. • There was no stoichiometry transfer as would be expected from Pulsed Laser Deposition.
Rola otyłości w patogenezie chorób alergicznych
Directory of Open Access Journals (Sweden)
Anna Grad
2009-09-01
Full Text Available W ostatnich latach wzrosła zachorowalność na astmę i inne choroby alergiczne. Jednocześnie obserwuje się zwiększenie liczby pacjentów z nadmierną masą ciała i podwyższoną wartością wskaźnika wagowo-wzrostowego (BMI. Wydaje się, że mimo odmiennego patomechanizmu astmy i otyłości istnieje wspólne ogniwo patogenetyczne rozwoju tych chorób. Bierze się pod uwagę rolę czynników środowiskowych, dietetycznych, genetycznych i infekcyjnych. Wyniki większości badań epidemiologicznych potwierdzają związek nadwagi i otyłości z ryzykiem wystąpienia astmy zarówno u osób dorosłych, jak i u dzieci. Podkreśla się rolę wysokiej urodzeniowej masy ciała i większych przyrostów masy ciała w pierwszym roku życia. Natomiast występowanie alergicznego nieżytu nosa i alergicznego zapalenia spojówek koreluje ujemnie z masą ciała. Nie obserwowano związku otyłości z częstością występowania atopowego zapalenia skóry. Tkanka tłuszczowa jako narząd endokrynny produkuje dużo różnych cytokin, hormonów, czynników wzrostu. Jest źródłem czynników prozapalnych, między innymi IL-6, TNF-a, TGF-b, leptyny, rezystyny. Leptyna jest produkowana przez adipocyty, jej stężenie koreluje z masą tkanki tłuszczowej, może ona intensyfikować zapalenie oraz odgrywać ważną rolę w rozwoju płuc. Podwyższone stężenie leptyny w surowicy jest uważane za czynnik prognostyczny rozwoju astmy. Adiponektyna ma właściwości przeciwzapalne, jej stężenie maleje w otyłości i koreluje ujemnie ze wskaź- nikiem BMI. W rozwoju astmy u osób otyłych biorą również udział rezystyna, eotaksyna, białko aP2 oraz żeńskie hormony płciowe. Rola czynników genetycznych nie jest do końca poznana. Dotychczas wyodrębniono 4 regiony chromosomalne związane ze zwiększoną podatnością na zachorowanie na astmę i otyłość. Efekt ochronny mają czynniki dietetyczne, takie jak antyoksydanty i mikroelementy. Otyłość pogarsza
Rola otyłości w patogenezie chorób alergicznych
Directory of Open Access Journals (Sweden)
Anna Grad
2008-10-01
Full Text Available W ostatnich latach wzrosła zachorowalność na astmę i inne choroby alergiczne. Jednocześnie obserwuje się zwiększenie liczby pacjentów z nadmierną masą ciała i podwyższoną wartością wskaźnika wagowo-wzrostowego (BMI. Wydaje się, że mimo odmiennego patomechanizmu astmy i otyłości istnieje wspólne ogniwo patogenetyczne rozwoju tych chorób. Bierze się pod uwagę rolę czynników środowiskowych, dietetycznych, genetycznych i infekcyjnych. Wyniki większości badań epidemiologicznych potwierdzają związek nadwagi i otyłości z ryzykiem wystąpienia astmy zarówno u osób dorosłych, jak i u dzieci. Podkreśla się rolę wysokiej urodzeniowej masy ciała i większych przyrostów masy ciała w pierwszym roku życia. Natomiast występowanie alergicznego nieżytu nosa i alergicznego zapalenia spojówek koreluje ujemnie z masą ciała. Nie obserwowano związku otyłości z częstością występowania atopowego zapalenia skóry. Tkanka tłuszczowa jako narząd endokrynny produkuje dużo różnych cytokin, hormonów, czynników wzrostu. Jest źródłem czynników prozapalnych, między innymi IL-6, TNF-a, TGF-b, leptyny, rezystyny. Leptyna jest produkowana przez adipocyty, jej stężenie koreluje z masą tkanki tłuszczowej, może ona intensyfikować zapalenie oraz odgrywać ważną rolę w rozwoju płuc. Podwyższone stężenie leptyny w surowicy jest uważane za czynnik prognostyczny rozwoju astmy. Adiponektyna ma właściwości przeciwzapalne, jej stężenie maleje w otyłości i koreluje ujemnie ze wskaź- nikiem BMI. W rozwoju astmy u osób otyłych biorą również udział rezystyna, eotaksyna, białko aP2 oraz żeń- skie hormony płciowe. Rola czynników genetycznych nie jest do końca poznana. Dotychczas wyodrębniono 4 regiony chromosomalne związane ze zwiększoną podatnością na zachorowanie na astmę i otyłość. Efekt ochronny mają czynniki dietetyczne, takie jak antyoksydanty i mikroelementy. Otyłość pogarsza
International Nuclear Information System (INIS)
Maziasz, P.J.; Klueh, R.L.
1988-01-01
Special austenitic steels are being designed in which alloying elements like Mo, Nb, and Ni are replaced with Mn, W, V, Ti, and/or Ta to reduce the long-term radioactivity induced by fusion reactor irradiation. However, the new steels still need to have properties otherwise similar to commercial steels like type 316. Precipitation strongly affects strength and radiation-resistance in austenitic steels during irradiation at 400--600/degree/C, and precipitation is also usually quite sensitive to alloy composition. The initial stage of development was to define a base Fe-Cr-Mn-C composition that formed stable austenite after annealing and cold-working, and resisted recovery or excessive formation of coarse carbide and intermetallic phases during elevated temperature annealing. These studies produced a Fe-12Cr-20Mn-0.25C base alloy. The next stage was to add the minor alloying elements W, Ti, V, P, and B for more strength and radiation-resistance. One of the goals was to produce fine MC precipitation behavior similar to the Ti-modified Fe-Cr-Ni prime candidate alloy (PCA). Additions of Ti+V+P+B produced fine MC precipitation along network dislocations and recovery/recrystallization resistance in 20% cold worked material aged at 800/degree/C for 166h, whereas W, Ti, W+Ti, or Ti+P+B additions did not. Addition of W+Ti+V+P+B also produced fine MC, but caused some σ phase formation and more recrystallization as well. 29 refs., 14 figs., 9 tabs
The changes in the electronic structure of B2 FeAl alloy with a Fe antisite and absorbed hydrogen
International Nuclear Information System (INIS)
Gonzalez, E.A.; Jasen, P.V.; Luna, R.; Bechthold, P.; Juan, A.; Brizuela, G.
2009-01-01
The electronic structure and bonding in a B2 FeAl alloy with and without hydrogen interaction with a Fe antisite were computed using a density functional theoretical method. The hydrogen absorption turns out to be a favorable process. The hydrogen was found close to an octahedral site where one of its Al capped is replaced by a Fe antisite. The Fe-H distance is of 1.45 A same as the Al-H distance. The density of states (DOS) curves show several peaks below the d metal band which is made up mostly of hydrogen based states (>50% H 1s ) while the metal contribution in this region includes mainly s and p orbitals. An electron transfer of nearby 0.21e - comes from the metal to the H. The overlap population values reveal metal-metal bond breaking, the intermetallic bond being the most affected. The H bond mainly with the Al atom and the reported Fe-H overlap population is much lower than that corresponding to FePd alloys and BCC Fe. The changes in the overlap population show the Fe-Al bond is weakened nearly 41.5% after H absorption, while the Fe-Fe bond is only weakened 34.5%. H also develops a stronger bond with the Al atoms. The main bond is developed with Al being twice stronger than Fe-H.
Corrosion resistance of sintered NdFeB coated with SiC/Al bilayer thin films by magnetron sputtering
International Nuclear Information System (INIS)
Huang, Yiqin; Li, Heqin; Zuo, Min; Tao, Lei; Wang, Wei; Zhang, Jing; Tang, Qiong; Bai, Peiwen
2016-01-01
The poor corrosion resistance of sintered NdFeB imposes a great challenge in industrial applications. In this work, the SiC/Al bilayer thin films with the thickness of 510 nm were deposited on sintered NdFeB by magnetron sputtering to improve the corrosion resistance. A 100 nm Al buffer film was used to reduce the internal stress between SiC and NdFeB and improve the surface roughness of the SiC thin film. The morphologies and structures of SiC/Al bilayer thin films and SiC monolayer film were investigated with FESEM, AFM and X-ray diffraction. The corrosion behaviors of sintered NdFeB coated with SiC monolayer film and SiC/Al bilayer thin films were analyzed by polarization curves. The magnetic properties were measured with an ultra-high coercivity permanent magnet pulse tester. The results show that the surface of SiC/Al bilayer thin films is more compact and uniform than that of SiC monolayer film. The corrosion current densities of SiC/Al bilayer films coated on NdFeB in acid, alkali and salt solutions are much lower than that of SiC monolayer film. The SiC/Al bilayer thin films have little influence to the magnetic properties of NdFeB. - Highlights: • The same thick Al, SiC and SiC/Al films are deposited on NdFeB by magnetron sputtering. • 510 nm SiC/Al bilayer films can improve the corrosion resistance of the NdFeB evidently. • Al buffer layer improves effectively the surface roughness of the SiC thin film. • SiC/Al bilayer films do not deteriorate the magnetic properties of NdFeB.
Corrosion resistance of sintered NdFeB coated with SiC/Al bilayer thin films by magnetron sputtering
Energy Technology Data Exchange (ETDEWEB)
Huang, Yiqin [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Li, Heqin, E-mail: lhqjs@hfut.edu.cn [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Zuo, Min; Tao, Lei; Wang, Wei [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Zhang, Jing; Tang, Qiong [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); School of Electronic Science and Applied Physics, Hefei University of Technology, Hefei 230009 (China); Bai, Peiwen [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China)
2016-07-01
The poor corrosion resistance of sintered NdFeB imposes a great challenge in industrial applications. In this work, the SiC/Al bilayer thin films with the thickness of 510 nm were deposited on sintered NdFeB by magnetron sputtering to improve the corrosion resistance. A 100 nm Al buffer film was used to reduce the internal stress between SiC and NdFeB and improve the surface roughness of the SiC thin film. The morphologies and structures of SiC/Al bilayer thin films and SiC monolayer film were investigated with FESEM, AFM and X-ray diffraction. The corrosion behaviors of sintered NdFeB coated with SiC monolayer film and SiC/Al bilayer thin films were analyzed by polarization curves. The magnetic properties were measured with an ultra-high coercivity permanent magnet pulse tester. The results show that the surface of SiC/Al bilayer thin films is more compact and uniform than that of SiC monolayer film. The corrosion current densities of SiC/Al bilayer films coated on NdFeB in acid, alkali and salt solutions are much lower than that of SiC monolayer film. The SiC/Al bilayer thin films have little influence to the magnetic properties of NdFeB. - Highlights: • The same thick Al, SiC and SiC/Al films are deposited on NdFeB by magnetron sputtering. • 510 nm SiC/Al bilayer films can improve the corrosion resistance of the NdFeB evidently. • Al buffer layer improves effectively the surface roughness of the SiC thin film. • SiC/Al bilayer films do not deteriorate the magnetic properties of NdFeB.
B and W NPGD quality assurance program for nuclear equipment. Revision 1
International Nuclear Information System (INIS)
1975-03-01
B and W's Quality Assurance Program (QAP) is described. The program is implemented through the Nuclear Power Generation Division (NPGD) and includes design, procurement, and manufacturing activities of NPGD and all its suppliers furnishing items in the B and W scope of supply including other Divisions/ Subsidiaries of B and W. These activities are controlled by including applicable quality assurance requirements, as described, in NPGD procurement documents imposed on its suppliers. Each supplier must then establish and/or maintain a documented QA Program to meet the requirements imposed by the procurement documents. Implementation of the suppliers' NPGD-approved QA Program is verified by NPGD through Audit and QC Surveillance activities. The position and relationships of the NPGD within the Company's corporate structure are described. An overview of the QAP describing its implementation, its operation, the controls imposed on all suppliers (both corporate and vendor) and site consulting activities is presented. (U.S.)
Structural, magnetic and optical properties of Y bFe{sub 2}O{sub 4} films deposited by spin coating
Energy Technology Data Exchange (ETDEWEB)
Fujii, Tatsuo, E-mail: tfujii@cc.okayama-u.ac.jp; Okamura, Naoya; Hashimoto, Hideki; Nakanishi, Makoto [Department of Applied Chemistry, Okayama University, 3-1-1 Tsushima-naka, Kita-ku, Okayama 700-8530 (Japan); Kano, Jun [Department of Applied Chemistry, Okayama University, 3-1-1 Tsushima-naka, Kita-ku, Okayama 700-8530 (Japan); Japan Science and Technology Agency, PRESTO, Kawaguchi, Saitama 332-0012 (Japan); Ikeda, Naoshi [Department of Physics, Okayama University, 3-1-1 Tsushima-naka, Kita-ku, Okayama 700-8530 (Japan)
2016-08-15
Rare-earth iron oxides (RFe{sub 2}O{sub 4}) have attracting attention as new electronic device materials because of their numerous functionalities, such as electronic ferroelectricity, ferrimagnetism, and high infrared absorption. In this paper, nearly monophasic Y bFe{sub 2}O{sub 4} films were prepared on α-Al{sub 2}O{sub 3}(001) substrates by the spin coating method using an aqueous-based Y bFe{sub 2}O{sub 4} solution. The solution was composed of a stoichiometric ratio of Y b(CH{sub 3}COO){sub 3} and Fe(NO{sub 3}){sub 3} with excess chelating agents. After heat treatment above 800 °C, well-crystallized and highly (001)-oriented Y bFe{sub 2}O{sub 4} started to epitaxially form on the substrate under controlled oxygen partial pressure with H{sub 2}/CO{sub 2} gas mixtures. X-ray pole figure analysis confirmed the following epitaxial relationship: Y bFe{sub 2}O{sub 4}[100](001)//α-Al{sub 2}O{sub 3}[100](001). Moreover formation of an Fe{sub 3}O{sub 4} interracial layer between Y bFe{sub 2}O{sub 4} and α-Al{sub 2}O{sub 3} was detected by high-resolution transmission electron microscopy. Presence of the Fe{sub 3}O{sub 4} interracial layer seemed to release the lattice misfit with the substrate. The Fe{sup 2+}/Fe{sup 3+} ratio in the obtained Y bFe{sub 2}O{sub 4} films was nearly stoichiometric and the indirect bandgap assigned to Fe{sup 2+} → Fe{sup 3+} charge transfer excitation was found to be ∼0.4 eV by optical spectroscopy. A clear magnetic transition from the paramagnetic state to the ferrimagnetic state occurred at ∼230 K.
Moessbauer Investigation of Spin Arrangements in Er2-xCexFe14B
International Nuclear Information System (INIS)
Bogacz, B.F.; Pedziwiatr, A.T.
2008-01-01
It was theoretically postulated earlier that in compounds Er 2-x Ce x Fe 14 B it may be possible to observe not only axial and planar spin arrangements but also a conical one. In order to experimentally verify this hypothesis, 57 Fe Moessbauer spectroscopy analysis was used to study the polycrystalline compounds Er 2-x Ce x Fe 14 B in the postulated composition region (x = 1.0, 1.1, 1.2, 1.3) in the wide range of temperatures. The obtained experimental data do not clearly support the suggestion of conical arrangement occurrence in the postulated compositions. They indicate that such phenomenon may be shifted towards higher Ce content. (authors)
Multi-jump magnetic switching in ion-beam sputtered amorphous Co20Fe60B20 thin films
International Nuclear Information System (INIS)
Raju, M.; Chaudhary, Sujeet; Pandya, D. K.
2013-01-01
Unconventional multi-jump magnetization reversal and significant in-plane uniaxial magnetic anisotropy (UMA) in the ion-beam sputtered amorphous Co 20 Fe 60 B 20 (5–75 nm) thin films grown on Si/amorphous SiO 2 are reported. While such multi-jump behavior is observed in CoFeB(10 nm) film when the magnetic field is applied at 10°–20° away from the easy-axis, the same is observed in CoFeB(12.5 nm) film when the magnetic field is 45°–55° away from easy-axis. Unlike the previous reports of multi-jump switching in epitaxial films, their observance in the present case of amorphous CoFeB is remarkable. This multi-jump switching is found to disappear when the films are crystallized by annealing at 420 °C. The deposition geometry and the energy of the sputtered species appear to intrinsically induce a kind of bond orientation anisotropy in the films, which leads to the UMA in the as-grown amorphous CoFeB films. Exploitation of such multi-jump switching in amorphous CoFeB thin films could be of technological significance because of their applications in spintronic devices
A Transdermal Drug Delivery System Based on LIGA Technology and Soft Lithography
Matteucci, Marco; Perennes, Frederic; Marmiroli, Benedetta; Di Fabrizio, Enzo
2007-01-01
This report presents a transdermal drug delivery system based on LIGA fabricated microparts. It is a portable device combining a magnetically actuated micro gear pump with a microneedle array. The fluidic behaviour of the system is analyzed in order to predict its performance according to the dimension of the microparts and then compared to experimental data. The manufacturing process of both micropump and microneedle array are described.
Improvement of the microstructure and magnetic properties of sintered NdFeB permant magnets
International Nuclear Information System (INIS)
Vial, F.; Rozendaal, E.; Sagawa, M.
1998-01-01
A correlation between sintered NdFeB process, microstructure of the products at each step of the process and magnetic properties has been established. To increase (BH) max of sintered NdFeB magnets, the total rare-earth content in the alloy has to be decreased and to keep coercivity as high as possible, the unavoidable oxygen pick-up has to be substantially reduced. The composition improvements tend to create a high sensitivity to form abnormal grain growth which can potentially occur during the sintering operation. Special attention has been given to characterising, understanding the mechanisms and solving this defect which could affect the magnetic properties. In addition, the composition and each step of the process have been optimised to improve magnetic properties, thermal stability and corrosion resistance of the NdFeB permanent magnets. These collaborative studies have resulted in a significant improvement of both remanence and coercivity of the sintered NdFeB permanent magnets, covering a wide coercivity range from 800 to 2500 kA/m (10 to 35 kOe) with respective associated energy products of 400 to 270 kJ/m3 (52 to 35 MGOe). (orig.)
Effects of proton irradiation on electronic structure of NdFeB permanent magnets
Energy Technology Data Exchange (ETDEWEB)
Yang, L. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Zhen, L. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)], E-mail: lzhen@hit.edu.cn; Xu, C.Y.; Sun, X.Y.; Shao, W.Z. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)
2009-09-15
Effects of proton irradiation on electronic structure and atomic local structure of N35EH-type NdFeB permanent magnet were investigated by soft X-ray absorption spectrometry and Moessbauer spectrometry. The local coordination environment of Fe atoms changes after proton irradiation, and the average hyperfine field H{sub in} of the magnets decreases from 288.4 to 286.9 kOe. The effects of irradiation on Fe atoms local environment at different lattice sites are different. The near edge structure of Fe L{sub 3} edge is changed, indicating the density of unoccupied state of Fe 3d electrons increases after proton irradiation.
Fabrication of a solenoid-type inductor with Fe-based soft magnetic core
International Nuclear Information System (INIS)
Lei Chong; Zhou Yong; Gao Xiaoyu; Ding Wen; Cao Ying; Choi, Hyung; Won, Jonghwa
2007-01-01
A solenoid-type inductor was fabricated by MEMS (Microelectromechanical systems) technique. The fabrication process uses UV-LIGA, dry etching, fine polishing, and electroplating technique to achieve high performance of the solenoid-type inductor. Fe-based soft magnetic thin film was sputtered as the magnetic core, and polyimide was used as the insulation materials. The inductor was in size of 4x4 mm with coil width of 20 μm and space of 35 μm. The inductance is 1.61 μH at a frequency of 5 MHz with the maximum quality factor of 1.42
Soft and hard natures of Nd2Fe14B permanent magnet explored by first-order-reversal-curves
International Nuclear Information System (INIS)
Chen, Po-An; Yang, Chao-Yao; Chang, Shu-Jui; Lee, Min-Han; Tang, Nai-Kuang; Yen, Sheng-Chan; Tseng, Yuan-Chieh
2014-01-01
Two commercial Nd 2 Fe 14 B samples, MQP-B and sintered-NdFeB were investigated using synchrotron-based x-ray diffraction and first-order-reversal-curves (FORCs). Despite differing in magnetic and structural properties, the two samples were found to comprise two major ferromagnetic components in FORCs. For the sintered-NdFeB case, the soft component may originate from the intrinsically soft Nd-f site which was coupled with its local Fe atomic environment that differs in magnetic anisotropy from the Nd-g site (intrinsically hard). It may directly originate from the Nd-rich phase or microstructural imperfection, while the former possibility (Nd-f site) appears greater than the latter. While for the MQP-B, the minor second phase resulting from high structural disorder was likely in charge of the presence of the soft component. Sophisticated FORCs analyses revealed the natures of the soft and hard components, soft–hard coupling and switching reversibility of the two cases, irrespective of the origins of their two components. This provides insights to the origin of magnetic stability and reversal dynamics of Nd 2 Fe 14 B that have not been fully understood by conventional magnetic analyses. The coexistence of the two components led to an incoherent reversal undermining the magnetic stability of Nd 2 Fe 14 B. This is a fundamental problem as to why the performance extremity can only be improved finitely through extrinsic tuning. From FORCs simulation we understand that the soft–hard coupling was moderate in a real Nd 2 Fe 14 B compound. A stronger soft–hard coupling is necessary to conquer the anisotropic competition to enable a coherent reversal that will promote the magnetic hardness. - Highlights: • We investigated two commercially available Nd 2 Fe 14 B compounds with FORCs. • The two compounds were found to comprise soft and hard natures. • The coupling between the soft and hard phases is moderate in a real Nd 2 Fe 14 B
Application of bonded NdFeB magnet for C-Band circulator component
Kristiantoro, T.; Idayanti, N.; Sudrajat, N.; Septiani, A.; Dedi
2016-11-01
In this paper bonded NdFeB permanent magnets of the crashed-ribbon type were made as an alternative for circulator magnet to improve their magnetic performance. The fabrication process is also easier than the sintered NdFeB because there had no shrinkage of product (such as sintered barium ferrite magnet), with the others advantages as follows; large freeness of product shapes, high precision of dimension and good corrosion resistance. The dimension of the samples was measured to calculate its bulk densities and the magnetic properties were characterized by Permagraph to obtain values such as; Remanence induction (Br) in kG, Coercivity value (Hcj) in kOe, the Maximum energy product (BH max) in MGOe. Whereas the surface magnetic field strength (B) was observed by the Gauss-meter. The bonded NdFeB permanent magnets revealed 6.39 kG of Br, 6.974 kOe of Hcj and 7.13 MGOe of BHmax. The circulator performance was measured using Vector Network Analyzer (VNA). The optimum values of the circulator measurement at a frequency of 5 GHz show a VSWR value of 1.062 and insertion loss of -0.463 dB. The bonded magnet could be used as component of permanent magnets on the circulator that working on C-Band at a frequency range of 4 GHz - 8 GHz.
Directory of Open Access Journals (Sweden)
Elba Guerrero
2013-03-01
Full Text Available The relation of ethambutol resistance to embB mutations remains unclear, and there are no reports on ethambutol resistance from the Caribbean. We examined the sequence of embB in 57 distinct Multi-Drug Resistant (MDR and non-MDR strains of Mycobacterium tuberculosis, mostly from Cuba and the Dominican Republic. embB306 codon mutations were found exclusively in MDR-TB, but in both ethambutol sensitive and resistant strains. Valine substitutions predominated in ethambutol resistant strains, while isoleucine replacements were more common in sensitive strains. Three ethambutol resistant MDR strains without embB306 substitutions had replacements in embB406 or embB497, but these were also found in ethambutol sensitive MDR strains. The results confirm previous findings that amino acid substitutions in EmbB306, EmbB406 and EmbB497 are found only in MDR-TB strains but in both phenotypically resistant and sensitive strains. One ethambutol resistant non-MDR strain did not have any embB mutation suggesting that other undefined mutations can also confer ethambutol resistance.La relación entre resistencia a etambutol y mutaciones en embB no se ha establecido claramente y no existen comunicaciones sobre la resistencia a etambutol en cepas provenientes de países Caribeños. Se evaluó la secuencia del gen embB en 57 cepas de Mycobacterium tuberculosis multi-drogo resistentes (MDR y no-MDR, la mayoría aislada en Cuba y República Dominicana. Se encontraron mutaciones en el codón embB306 exclusivamente en cepas MDR, tanto en cepas sensibles como resistentes a etambutol. Tres cepas MDR resistentes a etambutol, sin sustituciones en embB306, tenían mutaciones en los codones embB406 o embB497, pero estos cambios se encontraron también en cepas sensibles. Los resultados confirman otros estudios, mostrando que sustituciones aminoacídicas en EmbB306, EmbB406 y EmbB497 se encuentran exclusivamente en cepas MDR, tanto resistentes como sensibles a etambutol
Magnetic properties of melt-spun Nd-rich NdFeB alloys with Dy and Ga substitutions
International Nuclear Information System (INIS)
Harland, C.L.; Davies, H.A.
1998-01-01
The results of a systematic investigation of the effects of Dy and Ga additions on the magnetic properties of a Nd-rich NdFeB alloy are presented and discussed. Particular attention is given to the effect of increasing Dy substitutions on the coercivity of the Nd 18 Fe 76 B 6 alloy. Substitution of 30% of the Nd by Dy resulted in a coercivity increase from 1590 to 3290 kA m -1 . However, contrary to previous suggestions, substitution of 1% of the Fe by Ga was found to have only a small influence on the magnetic properties of all the alloys in the compositional series (Nd 100-x Dy x ) 18 Fe 76 B 6 (x=0-30). (orig.)
Directory of Open Access Journals (Sweden)
ROLLO João Manuel Domingos de Almeida
1999-01-01
Full Text Available Uma das aplicações tecnológicas em que é necessário haver compatibilidade entre um material cerâmico e um material metálico é a confecção de restaurações odontológicas do tipo metalocerâmica. Neste caso, uma porcelana é fundida sobre um substrato metálico para obtenção da prótese de um dente. O requisito fundamental para o sucesso da união metalocerâmica é a adequação dos coeficientes de expansão térmica de cada um dos materiais, de forma a se obter um estado de tensão de compressão adequado na camada cerâmica. Este trabalho propôs-se a levantar as curvas de expansão térmica de ligas Ni-Cr e porcelanas odontológicas, através da técnica de dilatometria e verificar a possível compatibilidade térmica dos pares metal/cerâmica. Simulando a entrada de um novo produto no mercado, desenvolveu-se uma liga Ni-Cr experimental denominada SR, que foi comparada a uma liga comercial de Ni-Cr bastante utilizada em restaurações metalocerâmicas. A partir da análise das curvas de expansão térmica, foi possível verificar a compatibilidade dos pares metal/cerâmica quanto à dilatação térmica, segundo os conceitos preconizados por YAMAMOTO7 (1985. Sob este aspecto, a liga experimental apresentou valores que a incluem como mais uma opção na família de ligas Ni-Cr para utilização em restaurações metalocerâmicas. Os resultados obtidos indicam que o equipamento e a metodologia utilizados são adequados para análise comparativa da compatibilidade térmica entre ligas metálicas Ni-Cr e porcelanas odontológicas.
In-situ magnetization of NdFeB magnets for permanent magnet machines
International Nuclear Information System (INIS)
Chang, L.; Eastham, T.R.; Dawson, G.E.
1991-01-01
In-situ magnetizers are needed to facilitate the assembly of permanent magnet machines and to remagnetize the magnets after weakening due to a fault condition. The air-core magnetizer in association with the silicon steel lamination structure of the rotor has advantages over its iron-core counterpart. This novel method has been used to magnetize the NdFeB magnets in a 30-hp permanent magnet synchronous motor. The magnetizing capability for different magnetizer geometries was investigated for the magnetization of NdFeB material. The design, testing, and operation of this magnetizer are reported in this paper
W.E.B. DuBois's Challenge to Scientific Racism.
Taylor, Carol M.
1981-01-01
Proposes that a direct and authoritative challenge to the scientific racism of the late eighteenth and early twentieth centuries was urgently needed, and was one of the leading rhetorical contributions of W.E.B. DuBois. Specifically examines three issues: social Darwinism, the eugenics movement, and psychologists' measurement of intelligence.…